WorldWideScience

Sample records for sand mountain parish

  1. Louisiana ESI: PARISH (Parish Management Area Polygons)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains boundaries for parishes in coastal Louisiana. Vector polygons in this data set represent parish management areas. Location-specific type and...

  2. Giving Claiborne Parish the business

    International Nuclear Information System (INIS)

    Holman, B.

    1994-01-01

    Residents of Claiborne Parish, Louisiana, learned four years ago of plans to build a commercial uranium enrichment plant in their community. This article provides a brief history of the situation at U.S. utilities, specifically Louisiana Energy, which led to the selection of Claiborne Parish as a site of a new commercial plant. The effects of the changing market caused by the end of the Cold War which have made licensing of the plant unlikely are described. The political controversy surrounding the plant and public opinion of Claiborne Parish residents are presented. The possible impact of commercial enrichment plants on the U.S. fuel supply is evaluated

  3. Vertical accretion sand proxies of gaged floods along the upper Little Tennessee River, Blue Ridge Mountains, USA

    Science.gov (United States)

    Leigh, David S.

    2018-02-01

    Understanding environmental hazards presented by river flooding has been enhanced by paleoflood analysis, which uses sedimentary records to document floods beyond historical records. Bottomland overbank deposits (e.g., natural levees, floodbasins, meander scars, low terraces) have the potential as continuous paleoflood archives of flood frequency and magnitude, but they have been under-utilized because of uncertainty about their ability to derive flood magnitude estimates. The purpose of this paper is to provide a case study that illuminates tremendous potential of bottomland overbank sediments as reliable proxies of both flood frequency and magnitude. Methods involve correlation of particle-size measurements of the coarse tail of overbank deposits (> 0.25 mm sand) from three separate sites with historical flood discharge records for the upper Little Tennessee River in the Blue Ridge Mountains of the southeastern United States. Results show that essentially all floods larger than a 20% probability event can be detected by the coarse tail of particle-size distributions, especially if the temporal resolution of sampling is annual or sub-annual. Coarser temporal resolution (1.0 to 2.5 year sample intervals) provides an adequate record of large floods, but is unable to discriminate individual floods separated by only one to three years. Measurements of > 0.25 mm sand that are normalized against a smoothed trend line through the down-column data produce highly significant correlations (R2 values of 0.50 to 0.60 with p-values of 0.004 to Time-series data of particle-size should be detrended to minimize variation from dynamic aspects of fluvial sedimentation that are not related to flood magnitude; and 5) Multiple sites should be chosen to allow for replication of findings.

  4. Mountains

    Science.gov (United States)

    Regina M. Rochefort; Laurie L. Kurth; Tara W. Carolin; Robert R. Mierendorf; Kimberly Frappier; David L. Steenson

    2006-01-01

    This chapter concentrates on subalpine parklands and alpine meadows of southern British Columbia, Washington, Oregon, and western Montana. These areas lie on the flanks of several mountain ranges including the Olympics, the Cascades of Oregon and Washington, and the Coast Mountains in British Columbia.

  5. Zoning, 2004, East Baton Rouge Parish, Louisiana

    Data.gov (United States)

    Louisiana Geographic Information Center — This is a graphical polygon dataset depicting the zoning boundaries of the East Baton Rouge Parish of the State of Louisiana. Zoning can be defined as the range of...

  6. Hydrography, 2004, East Baton Rouge Parish, Louisiana

    Data.gov (United States)

    Louisiana Geographic Information Center — The Hydrography layer is an area geometry depicting the various water features that include the rivers, streams, creeks, lakes, etc of East Baton Rouge Parish.

  7. Sand Dredging Operations in Lafourche Parish, Near Leeville, Louisiana.

    Science.gov (United States)

    1982-04-01

    hunting was permitted during 1979. However, there are no permits to kill alligators issued for areas below the 10 parts per thousand isohaline line...Northern House Wern Thryothorus ludovicianus Carolina Wren IMimus polyglottos Northern Mockingbird Dumetella carolinensis Cray Catbird Toxostoma rufum

  8. Charismatic Practice and Catholic Parish Life

    DEFF Research Database (Denmark)

    Thorsen, Jakob Egeris

    In Charismatic Practice and Catholic Parish Life - the Incipient Pentecostalization of the Church in Guatemala and Latin America, Jakob Egeris Thorsen offers a detailed ethnographic and theological analysis of the impact of the Catholic Charismatic Renewal on the Catholic Church in the region....... Based on fieldwork, this interdisciplinary study examines how Charismatic practice and spirituality permeate both local parish life and the pastoral plans of the Catholic Church in Guatemala and Latin America. The Charismatic Renewal is the largest lay movement in Latin America and has a profound...

  9. Louisiana Parish Boundaries, Geographic NAD83, LDOTD (2007) [Parishes_LDOTD_2007

    Data.gov (United States)

    Louisiana Geographic Information Center — Louisiana Parish Boundaries approved by Resolution of the GIS Council on January 19, 2000. This is a region dataset depicting the polygon boundaries of the 64...

  10. Insight into the Fulnek Church and Parish Medieval Building Chronology

    Directory of Open Access Journals (Sweden)

    Augustinková Lucie

    2017-06-01

    Full Text Available The church of the Holy Trinity and parish in Fulnek was for nearly four centuries an Augustinian canonry and collegiate church (1293-1389. The medieval church and parish building chronology, however, have not been thus far established. From research between 2015 and 2016 we have been able to identify medieval portions of the buildings, clarify the site medieval construction phases and date the parish buildings (formerly the canonry from dendrochronological analysis of embedded wooden scaffolding.

  11. Faith community/parish nursing: what's in a name?

    Science.gov (United States)

    Patterson, Deborah L; Slutz, Mary

    2011-01-01

    In the Christian faith tradition, using "Parish Nurse" to describe the form of nursing based in a Christian congregation is both historic and descriptive of the type of nursing specialty practice and ministry that reaches within the Church and out into the wider community. Reflecting on the work of Granger Westberg, the Scope and Standards of Practice for this specialty, and examining the etiology of the word "parish," the authors argue that retaining the language "Parish Nurse"promotes a broader understanding of the purpose of this specialty practice, not only as inreach or outreach on behalf of a church or health system, but as a focused and integrated "parish" ministry.

  12. Spiritual care in Christian parish nursing.

    Science.gov (United States)

    van Dover, Leslie; Pfeiffer, Jane Bacon

    2007-01-01

    This paper reports the development of a substantive theory to explain the process parish nurses use to provide spiritual care to parishioners in Christian churches in a context where patients and nurses share a common set of values. Despite a surge of interest in spirituality and spiritual care in nursing, consensus is lacking on how care should be conceptualized and provided. Grounded theory method was used to explore and describe the processes 10 American parish nurses experienced and used as they gave spiritual care. Data were collected between 1998 and 2001. Participants were interviewed and audiotapes transcribed verbatim. Constant comparative methods were used to analyse more than 50 separate incidents reported by the nurses. From its initial emergence as the core category, 'Bringing God Near' became a Basic Social Process theory of giving spiritual care for these parish nurses. This Basic Social Process became a theory through writing theoretical memos that described how the 'main concern' of the nurses to give spiritual care was resolved. Phases within the process include: trusting God, forming relationships with the patient/family, opening to God, activating/nurturing faith and recognizing spiritual renewal or growth. The essence is bringing God near to people as they face health challenges. Findings from the study and spiritual care literature are integrated in the discussion. The parish nurses' spiritual challenge is to respond to what God is directing the nurse to be and do to strengthen people spiritually. This spiritual care can help restore the patient's sense of well-being, and encourage growth in faith. Those interested in providing and teaching spiritual care in the church context will find this theory useful as a conceptual guide.

  13. The Roman Catholic parish in Poland as the local community

    Directory of Open Access Journals (Sweden)

    Mariański Janusz

    2014-01-01

    Full Text Available In the Roman Catholic Church a parish is the smallest legal unit and it is the milieu for religious, social, and cultural activities for a group of people joined together in a geographical area. The purpose of this article is a sociological study examining the Catholic parish in Poland as a local community. Today a parish along with its community is exposed to social change and to myriad forces characteristic of the postmodern culture. In Poland two opposite forces characterize the life of a parish community: on the one side, secularization and individualization, and on the other side, socialization and evangelization. The subjective dimension of a local community, which is related to identification of people with a local parish, along with social bonds with the parish as a local community, are discussed in the first two sections of the article. In subsequent sections some issues related to common activities, membership in movements, religious communities, and Catholic associations within the parish will be presented. While the agency of people in the parish community is theoretically acknowledged, it is still not fully implemented. The discussion is based on the data obtained from major public opinion institutes in Poland.

  14. Fontainebleau Sand

    DEFF Research Database (Denmark)

    Leth, Caspar Thrane

    2006-01-01

    The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand.......The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand....

  15. THE PARISH AS AN OPEN SOCIETY

    Directory of Open Access Journals (Sweden)

    Constantin NECULA

    2015-04-01

    Full Text Available In all the thrill of the modern definitions of the social function of everyday life, we often forget about the basic human organizations that created the social cohesion which survived over the history during difficult times. A sort of memory aneurysm prevents us from rediscovering those communicational structures that created the real human community, which generated it free of any ideologies and fanaticisms, which raised it in the modern social network. The parish, humble social community based on the confession of the same faith and the stretching of a given geography, was mocked, eluded and informally deformed. It remains, though, one of the greatest miracles of the sociology of social organization, one of the communicational categories preserved, it seems, despite the evolution of virtual communication. It is enough to cross, for instance, the great highways of modern Europe, as well as the British area to see that the names of cities, thousands of them, are related to the Christian culture of the place. A certain saint or boards which attest the Christian past of the place, marking points of the spiritual amperage of the area, are lumps in an informal network that proves that the parish remains one of the sociological categories of communication that remains deeply implemented in the mentality of the modern man. Even if it lacks the same spiritual or cultural connotation, it remains the model of the open society, placed in the interval of the new models, destructured from the very moment of their hermeneutical assertion.

  16. 78 FR 46677 - Environmental Impact Statement; Calcasieu Parish, LA

    Science.gov (United States)

    2013-08-01

    ... DEPARTMENT OF TRANSPORTATION Federal Highway Administration Environmental Impact Statement...: The Federal Highway Administration is issuing this notice to advise the public that an Environmental Impact Statement (EIS) will be prepared for a proposed transportation project in Calcasieu Parish...

  17. Metro Council Districts, 2004, East Baton Rouge Parish, Louisiana

    Data.gov (United States)

    Louisiana Geographic Information Center — This is a graphical polygon dataset depicting the polygon boundaries of the twelve (12) Metropolitan Council Districts within the Parish of East Baton Rouge. The...

  18. Orientation of English Medieval Parish Churches

    Science.gov (United States)

    Hoare, Peter G.

    Our understanding of the alignment of English medieval parish churches, after more than three centuries of research, is far from complete. The arrangement of relatively few structures has been explained beyond reasonable doubt, and tests of the overwhelmingly popular festival orientation theory are often insufficiently rigorous to provide convincing answers. Much work remains to be done, including verifying and analyzing some of the existing raw data, determining whether the present church was dedicated at the time of construction, examining wills for evidence of early dedications, measuring the effect of eastern horizons on sunrise azimuths, and consulting excavation reports to assess whether earlier buildings may have influenced the arrangement of those churches that replaced them.

  19. Gulf-Wide Information System, Environmental Sensitivity Index Parishes, Geographic NAD83, LDWF (2001) [esi_parish_LDWF_2001

    Data.gov (United States)

    Louisiana Geographic Information Center — This data set contains boundaries for parishes in coastal Louisiana. Feature-specific contact, type, and source information are stored in relational data tables...

  20. Leadership networks in Catholic parishes: implications for implementation research in health.

    Science.gov (United States)

    Negrón, Rosalyn; Leyva, Bryan; Allen, Jennifer; Ospino, Hosffman; Tom, Laura; Rustan, Sarah

    2014-12-01

    Through two case studies of Catholic parishes in Massachusetts, this study explores the implications of leader-centered versus distributed leadership in Catholic parishes for the implementation of evidence-based health interventions. The two parishes involved in the study differ from each other in several ways. In the first, parishioners are less engaged in leadership activities at the decision-making level in the parish. A small group of lay volunteers work with the parish priest and other ordained leaders on parish activities. In the second parish, a large and active lay volunteer leadership have forged an organizational structure that allows more independence from the pastor's direct oversight. In this parish, lay volunteer leaders are the prime drivers of organizational programs and events. In 2012-2013, three types of networks were assessed at each parish: discussion, collaboration, and outside-of-parish ties. The contrasts between each parish include differences in density of collaboration, in frequency of discussion, and network centrality of the respective parish priests. We further identified key actors in the network structures at each parish. We discuss the implications of these findings for understanding organizational capacity in the context of health program implementation. Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. Parish nursing: a unique resource for community and district nurses.

    Science.gov (United States)

    Wordsworth, Helen; Moore, Ros; Woodhouse, Daphne

    2016-02-01

    This paper examines the effect of parish nursing as a faith community initiative to support the work of district and community nurses and improve health outcomes. It discusses the reasons why faith communities might embark upon health initiatives, and describes the practice of parish nursing and its history and development in the UK. With reference to both quantitative and qualitative outcomes, the relevance of the practice in the UK health scene is assessed. The paper suggests that connecting with the third sector through parish nursing could enhance the work of community and district nurses; this would present additional sources of holistic care and health promotion and can be offered in an optional but complementary manner to the care provided through the NHS.

  2. Connecting congregations: technology resources influence parish nurse practice.

    Science.gov (United States)

    Zerull, Lisa M; Near, Kelly K; Ragon, Bart; Farrell, Sarah P

    2009-01-01

    This descriptive pilot study evaluated the influence of health resource information education and the use of Web-based communication technology on the professional practice of the parish nurse in the congregational setting. Five parish nurse participants from varied denominations in rural and nonrural Virginia received a laptop computer, printer, video projector, and webcam along with high-speed Internet access in each congregational setting. The nurses attended two group education sessions that incorporated computer applications and training in accessing and using quality health information resources and communication applications such as a group "chat" software and webcam to communicate with others through high-speed Internet access. Qualitative analysis from semistructured interviews of nurses confirmed that participants found the project to be beneficial in terms of awareness, education, and applicability of technology use in parish nurse practice. Quantitative data from preproject and postproject surveys found significant differences in nurses' abilities and confidence with technology use and application. Findings showed that the knowledge and experience gained from this study enhanced parish nurse practice and confidence in using technology for communication, health education, and counseling.

  3. Sand consolidation

    Energy Technology Data Exchange (ETDEWEB)

    Spain, H H

    1965-01-21

    In a sand consolidation method in which there is injected a mixture of resin-forming liquids comprising an aryl-hydroxy low molecular weight compound, a water- soluble aldehyde, and a catalyst, an improvement is claimed which comprises diluting the resin-forming liquids with a diluent and with water so that the yield of the resin is sufficient to consolidate the sand particles with the minimum desirable pressure. The diluent may be mutually soluble in water and in the resin-forming liquids, and does not affect the setting time of the polymer. The aldehyde and the aryl-hydroxy compound may be in ratio of 5:1, and the diluent, methyl alcohol, is present in a ratio of 2:1 with reference to the water.

  4. Study of Black Sand Particles from Sand Dunes in Badr, Saudi Arabia Using Electron Microscopy

    Directory of Open Access Journals (Sweden)

    Haider Abbas Khwaja

    2015-08-01

    Full Text Available Particulate air pollution is a health concern. This study determines the microscopic make-up of different varieties of sand particles collected at a sand dune site in Badr, Saudi Arabia in 2012. Three categories of sand were studied: black sand, white sand, and volcanic sand. The study used multiple high resolution electron microscopies to study the morphologies, emission source types, size, and elemental composition of the particles, and to evaluate the presence of surface “coatings or contaminants” deposited or transported by the black sand particles. White sand was comprised of natural coarse particles linked to wind-blown releases from crustal surfaces, weathering of igneous/metamorphic rock sources, and volcanic activities. Black sand particles exhibited different morphologies and microstructures (surface roughness compared with the white sand and volcanic sand. Morphological Scanning Electron Microscopy (SEM and Laser Scanning Microscopy (LSM analyses revealed that the black sand contained fine and ultrafine particles (50 to 500 nm ranges and was strongly magnetic, indicating the mineral magnetite or elemental iron. Aqueous extracts of black sands were acidic (pH = 5.0. Fe, C, O, Ti, Si, V, and S dominated the composition of black sand. Results suggest that carbon and other contaminant fine particles were produced by fossil-fuel combustion and industrial emissions in heavily industrialized areas of Haifa and Yanbu, and transported as cloud condensation nuclei to Douf Mountain. The suite of techniques used in this study has yielded an in-depth characterization of sand particles. Such information will be needed in future environmental, toxicological, epidemiological, and source apportionment studies.

  5. Mineral sands

    International Nuclear Information System (INIS)

    Anon.

    1990-01-01

    This paper presents an outlook of the Australian mineral sand industry and covers the major operators. It is shown that conscious of an environmentally minded public, the Australian miners have led the way in the rehabilitation of mined areas. Moreover the advanced ceramic industry is generating exciting new perspectives for zircon producers and there is a noticeable growth in the electronic market for rare earths, but in long term the success may depend as much on environmental management and communication skills as on mining and processing skills

  6. 78 FR 62648 - Cat Island National Wildlife Refuge; West Feliciana Parish, Louisiana

    Science.gov (United States)

    2013-10-22

    ...-FF04R02000] Cat Island National Wildlife Refuge; West Feliciana Parish, Louisiana AGENCY: Fish and Wildlife... comprehensive conservation plan (CCP) and associated National Environmental Policy Act (NEPA) documents for Cat... our process for developing a CCP for Cat Island NWR, West Feliciana Parish, Louisiana. This notice...

  7. 78 FR 70318 - Cat Island National Wildlife Refuge; West Feliciana Parish, Louisiana; Notice of Intent To...

    Science.gov (United States)

    2013-11-25

    ...-FF04R02000] Cat Island National Wildlife Refuge; West Feliciana Parish, Louisiana; Notice of Intent To... comprehensive conservation plan (CCP) and associated National Environmental Policy Act (NEPA) documents for Cat... NEPA documents for Cat Island National Wildlife Refuge NWR, West Feliciana Parish, Louisiana, in a...

  8. Nursing body and soul in the parish: Lutheran deaconess motherhouses in Germany and the United States.

    Science.gov (United States)

    Kreutzer, Susanne

    2010-01-01

    In Lutheran Germany, parish nursing traditionally constituted the deaconesses' principal work. As "Christian mothers of the parish" they were charged with a wide spectrum of tasks, including nursing, social service, and pastoral care. At the center of the Christian understanding of nursing was the idea of nursing body and soul as a unity. This article analyzes the conception and transformation of Protestant parish nursing in the nineteenth and twentieth centuries in Germany and the United States, which developed very differently. In West Germany, parish nursing proved surprisingly resistant to modernization even in the face of upheavals of the 1960s, and in some places this traditional model survived as late as the 1980s and 1990s. In the United States, by contrast, an understanding of nursing rooted in the division of labor between care for body and care for soul had come to prevail by the 1920s and '30s, pushing out the German model of the parish deaconess altogether.

  9. Some factors affecting marital isonymy in three Outer Hebridean parishes.

    Science.gov (United States)

    Clegg, F J

    2001-01-01

    Log linear analysis was used to investigate the relationships between spouse isonymy and parental isonymy, time, endogamy/exogamy and groom's occupation in a total of 6266 first marriages of parish-born spouses in the civil parishes of Harris, Barra and Stornoway, between 1855 and 1990. Stornoway was divided into rural and urban (Burgh) components. Spouse isonymy comprised between 6% and 12% of all marriages, parental isonymy was generally slightly more frequent, due probably to the occurrence of occasional families in which both sets of parents were isonymous. Between 38% and 51% of marriages were endogamous. In the multi-way contingency tables, good fits between observed and expected cell numbers were obtained by a simple model, comprising the main effect of spouse isonymy and the first-order interactions between spouse isonymy and the independent variables. Inspection of the coefficients showed that in all four populations spouse isonymy was positively related to parental isonymy (doubtfully so in the case of Barra). The other independent variables showed less clear-cut relationships--endogamy/exogamy in Barra, and groom's occupation in Stornoway Rural; time period showed no significant relationships. It is concluded that the occurrence of this 'two-generational marital isonymy' might have an effect on the breeding structure of the population.

  10. 75 FR 29686 - Proposed Establishment of the Pine Mountain-Mayacmas Viticultural Area

    Science.gov (United States)

    2010-05-27

    ... states that local growers report that Pine Mountain vineyards are naturally free of mildew, a vineyard... often stall over Pine Mountain and the Mayacmas range, dropping more rain than in other areas. Pine..., these mountain soils include large amounts of sand and gravel. Pine Mountain soils are generally less...

  11. Was it possible to reform the Orthodox parish in 1890-s? The diocesan hierarchs on the transformation of the parish council of trustees (prihodskie popechitel’stva

    Directory of Open Access Journals (Sweden)

    Beglov Aleksandr

    2014-12-01

    Full Text Available In the article for the fi rst time in historiography the reviews of the diocesan bishops of the prospects of the reform of the parish council of trustees (prihodskie popechitel’stva at Orthodox churches are analysed in details. These reviews were submitted on request of the Ober-Procurator in the 1890s and they are analysed in the context of a more general transformation of the Orthodox parish, planned by K.P. Pobedonostsev. The reviews of the diocesan authorities about the possibilities of reforming the parish council of trustees were in fact revealing their attitude on the possibility of the parish reform in general. The author comes to the conclusion that the main idea of the reviews was to give the council of trustees more «church» character. The hierarchs saw two ways of realising this task. One of them could be called the administrative way, another one — the more natural one. The majority of hierarchy was in favor of the fi rst approach. They wanted to include the council of trustees in the existing system of diocesan administration, but subordinating them to the administrative control of the deans and the Consistory. Another group of hierarchs, which constituted the tenth part of all, who had submitted the reports, saw it necessary to transform the council of trustees into the voluntary parish brotherhoods, thereby choosing the religious active backbone of the parish. It is clear from the reports that they considered the experience of the Western Slavonic brotherhoods and the orthodox charity organisations which existed in America. However, neither of these projects was capable of solving the most important problem of parish life, that is the effi ciency of the parish economy, which was largely dependent on decisions of the peasant community. Bishops considered it possible to seek the help of the civil authorities in collecting the money from the parishioners. And only few were ready to give the parish organization the rights to be

  12. Bayou Corne sinkhole : control measurements of State Highway 70 in Assumption Parish, Louisiana, tech summary.

    Science.gov (United States)

    2014-01-01

    The sinkhole located in Assumption Parish, Louisiana, threatens the stability of Highway 70, a state maintained route. In order to : mitigate the potential damaging e ects of the sinkhole on this infrastructure, the Louisiana Department of Transpo...

  13. Bayou Corne sinkhole : control measurements of State Highway 70 in Assumption Parish, Louisiana.

    Science.gov (United States)

    2014-01-01

    This project measured and assessed the surface stability of the portion of LA Highway 70 that is : potentially vulnerable to the Assumption Parish sinkhole. Using Global Positioning Systems (GPS) : enhanced by a real-time network (RTN) of continuousl...

  14. Bayou Corne Sinkhole: Control Measurements of State Highway 70 in Assumption Parish, Louisiana : Research Project Capsule

    Science.gov (United States)

    2012-09-01

    The sinkhole located in northern Assumption Parish, Louisiana, threatens : the stability of Highway 70, a state-maintained route. In order to monitor : and mitigate potential damage eff ects on this infrastructure, the Louisiana : Department of Trans...

  15. Investigation and evaluation of geopressured-geothermal wells. Fairfax Foster Sutter No. 2 well, St. Mary Parish, Louisiana. Volume I. Completion and testing. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Willits, M.H.; McCoy, R.L.; Dobson, R.J.; Hartsock, J.H.

    1979-12-01

    The Fairfax Foster Sutter No. 2 well, located in the East Franklin area of St. Mary Parish, Louisiana, is the first successful test of a geopressured-geothermal aquifer under the Well-of-Opportunity program. The section tested was the MA-6 sand of lower Miocene age which has produced large quantities of gas from the adjacent but structurally separated Garden City field. In the subject well the observed temperature was 270{sup 0}F (132{sup 0}C) and the measured gradient was 0.77 psi/ft. The gross sand thickness was 270 feet, the net sand thickness 190 feet, and the tested interval 58 net feet. The temperatures and pressures encountered approached the limits of the surface-recording bottomhole pressure gauge and particularly the single-conductor cables on which the gauges were run. The objectives of the tests were all accomplished, and data were obtained which will contribute to the overall assessment of the geopressured-geothermal resource of the Upper Gulf of Mexico basin. In general, the gas solubility (22.8 scf/bbl) was as expected for the temperature, pressure, and salinity of the brine. The produced water was more saline than expected (160,000 mg/l). The high concentrations of dissolved solids, coupled with the evolution of CO{sub 2} from these waters during production, created a scaling problem in the tubular goods and surface equipment that will have to be addressed in future tests.

  16. Eastern Scheldt Sand, Baskarp Sand No. 15

    DEFF Research Database (Denmark)

    Andersen, A. T; Madsen, E. B.; Schaarup-Jensen, A. L.

    The present data report contains data from 13 drained triaxial tests, performed on two different sand types in the Soil Mechanics Laboratory at Aalborg University in March, 1997. Two tests have been performed on Baskarp Sand No. 15, which has already ken extensively tested in the Soil Mechanics...... Laboratory. The remaining 11 triaxial tests have ben performed on Eastern Scheldt Sand, which is a material not yet investigated at the Soil Mechanics Laboratory. In the first pari of this data report, the characteristics of the two sand types in question will be presented. Next, a description...... will described. In this connection, the procedure for preparation of the soil specimens will be presented, and the actual performance of the tests will be briefly outlined. Finally, the procedure for processing of the measurements from the laboratory in order to obtain usable data will be described. The final...

  17. Livingston Parish Landfill Methane Recovery Project (Feasibility Study)

    Energy Technology Data Exchange (ETDEWEB)

    White, Steven

    2012-11-15

    The Woodside Landfill is owned by Livingston Parish, Louisiana and is operated under contract by Waste Management of Louisiana LLC. This public owner/private operator partnership is commonplace in the solid waste industry today. The landfill has been in operation since approximately 1988 and has a permitted capacity of approximately 41 million cubic yards. Based on an assumed in-place waste density of 0.94 ton per cubic yard, the landfill could have an expected design capacity of 39.3 million tons. The landfill does have an active landfill gas collection and control system (LFGCCS) in place because it meets the minimum thresholds for the New Source Performance Standards (NSPS). The initial LFGCS was installed prior to 2006 and subsequent phases were installed in 2007 and 2010. The Parish received a grant from the United States Department of Energy in 2009 to evaluate the potential for landfill gas recovery and utilization at the Woodside Landfill. This includes a technical and economic feasibility study of a project to install a landfill gas to energy (LFGTE) plant and to compare alternative technologies. The LFGTE plant can take the form of on-site electrical generation, a direct use/medium Btu option, or a high-Btu upgrade technology. The technical evaluation in Section 2 of this report concludes that landfill gas from the Woodside landfill is suitable for recovery and utilization. The financial evaluations in sections 3, 4, and 5 of this report provide financial estimates of the returns for various utilization technologies. The report concludes that the most economically viable project is the Electricity Generation option, subject to the Parish’s ability and willingness to allocate adequate cash for initial capital and/or to obtain debt financing. However, even this option does not present a solid return: by our estimates, there is a 19 year simple payback on the electricity generation option. All of the energy recovery options discussed in this report

  18. 76 FR 66629 - Establishment of the Pine Mountain-Cloverdale Peak Viticultural Area

    Science.gov (United States)

    2011-10-27

    ... explains. The petition states that local growers report that Pine Mountain vineyards are naturally free of.... Southern storms often stall over Pine Mountain and the Mayacmas range, dropping more rain than in other..., and very well to excessively well-drained. Also, these mountain soils include large amounts of sand...

  19. Influence green sand system by core sand additions

    Directory of Open Access Journals (Sweden)

    N. Špirutová

    2012-01-01

    Full Text Available Today, about two thirds of iron alloys casting (especially for graphitizing alloys of iron are produced into green sand systems with usually organically bonded cores. Separation of core sands from the green sand mixture is very difficult, after pouring. The core sand concentration increase due to circulation of green sand mixture in a closed circulation system. Furthermore in some foundries, core sands have been adding to green sand systems as a replacement for new sands. The goal of this contribution is: “How the green sand systems are influenced by core sands?”This effect is considered by determination of selected technological properties and degree of green sand system re-bonding. From the studies, which have been published yet, there is not consistent opinion on influence of core sand dilution on green sand system properties. In order to simulation of the effect of core sands on the technological properties of green sands, there were applied the most common used technologies of cores production, which are based on bonding with phenolic resin. Core sand concentration added to green sand system, was up to 50 %. Influence of core sand dilution on basic properties of green sand systems was determined by evaluation of basic industrial properties: moisture, green compression strength and splitting strength, wet tensile strength, mixture stability against staling and physical-chemistry properties (pH, conductivity, and loss of ignition. Ratio of active betonite by Methylene blue test was also determined.

  20. Singing Sand Dunes

    Indian Academy of Sciences (India)

    ble low-frequency (s. 75–105 Hz), that can some- times be heard up to 10 km away. Scientific in- vestigations suggest that the sustained low fre- quency sound of sand dunes that resembles a pure note from a musical instrument, is due to the synchronized motion of well-sorted dry sand grains when they spontaneously ...

  1. Using community-based participatory research in parish nursing: a win-win situation!

    Science.gov (United States)

    Maitlen, Lynn A; Bockstahler, Amie M; Belcher, Anne E

    2012-01-01

    Parish nurses contribute to community health through the expertise and programming they provide to and through faith communities. Application of community-based participatory research (CBPR) principles helps develop, implement, and evaluate effective community interventions. University graduate students partnered with a Hospital Parish Nurse Program (HPNP) in an urban community to provide assessment data in a CBPR project that led the HPNP to focus resources and interventions on high obesity rates. The HPNP utilized data to write grant proposals to expand community services to impact obesity.

  2. New generation expandable sand screens

    OpenAIRE

    Syltøy, Christer

    2014-01-01

    Master's thesis in Petroleum engineering This thesis aims to give a general insight into sand control and various sorts of sand control measures and applications of sand control tools. Special focus will be given to expandable sand screens – a technology which came about in the late 1990’s through the use of flexible, expandable tubulars as base pipe in sand screens. More specifically Darcy’s Hydraulic Endurance Screens, a compliant sand screen system using hydraulic activation, and the fu...

  3. Mountaineering Tourism

    Directory of Open Access Journals (Sweden)

    Patrick Maher

    2016-08-01

    Full Text Available Reviewed: Mountaineering Tourism Edited by Ghazali Musa, James Higham, and Anna Thompson-Carr. Abingdon, United Kingdom: Routledge, 2015. xxvi + 358 pp. Hardcover. US$ 145.00. ISBN 978-1-138-78237-2.

  4. 77 FR 57492 - Drawbridge Operation Regulation; Grosse Tete Bayou, Iberville Parish, LA

    Science.gov (United States)

    2012-09-18

    ... modified from a moveable to a fixed bridge, without publishing an NPRM. The change removes the section of... the Union Pacific railroad swing bridge over Grosse Tete Bayou, mile 14.7, Iberville Parish, Louisiana. This bridge has been modified from a swing bridge to a fixed bridge and the current special operating...

  5. Leadership Development Experiences of Exemplary Roman Catholic Parish Priests: An Exploratory Study

    Science.gov (United States)

    Ong, Rosemarie A.

    2013-01-01

    This qualitative, phenomenological study addressed the research question: How do exemplary Roman Catholic parish priests perceive and describe their leadership development experience? The study explored experiences considered important in developing leadership, including how they occurred, the meaning provided, the definition of exemplary…

  6. Sand and Gravel Deposits

    Data.gov (United States)

    Vermont Center for Geographic Information — This dataset is a statewide polygon coverage of sand, gravel, and stone resources. This database includes the best data available from the VT Agency of Natural...

  7. Sand and Gravel Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes sand and gravel operations in the United States. These data were obtained from information reported voluntarily to the USGS by the aggregate...

  8. Retorting of bituminous sands

    Energy Technology Data Exchange (ETDEWEB)

    Chaney, P E; Ince, R W; Mason, C M

    1872-09-26

    This method of recovering oil from mined tar sands involves forming compacted tar sands pieces by special conditioning treatment that provides low internal permeability. The compacted pieces are then retorted in fixed bed form. The conditioning treatment can involve rolling of preformed pellets, compaction in a mold or pressure extrusion. Substantial collapsing of the bed during retorting is avoided. (9 claims) (Abstract only - original article not available from T.U.)

  9. MECHANICAL REGENERATION OF SAND WASTE

    Directory of Open Access Journals (Sweden)

    D. I. Gnir

    2005-01-01

    Full Text Available The experimental activation of the sand regenerator of the firm SINTO is carried out at ОАО “MZOO". It is shown that sand grains are cleared from films of binding agents, that allows to use the treated sand for preparation of agglutinant and core sands.

  10. Phase I Marine and Terrestrial Cultural Resources Survey of 13 Project Items Located on Marsh Island, Iberia Parish, Louisiana

    National Research Council Canada - National Science Library

    Barr, William

    1999-01-01

    This report presents the results of Phase I cultural resources survey and archeological inventory of two marine and 11 terrestrial project items on and near Marsh Island in Iberia Parish, Louisiana...

  11. Oil sands tax expenditures

    International Nuclear Information System (INIS)

    Ketchum, K; Lavigne, R.; Plummer, R.

    2001-01-01

    The oil sands are a strategic Canadian resource for which federal and provincial governments provide financial incentives to develop and exploit. This report describes the Oil Sands Tax Expenditure Model (OSTEM) developed to estimate the size of the federal income tax expenditure attributed to the oil sands industry. Tax expenditures are tax concessions which are used as alternatives to direct government spending for achieving government policy objectives. The OSTEM was developed within the business Income Tax Division of Canada's Department of Finance. Data inputs for the model were obtained from oil sands developers and Natural Resources Canada. OSTEM calculates annual revenues, royalties and federal taxes at project levels using project-level projections of capital investment, operating expenses and production. OSTEM calculates tax expenditures by comparing taxes paid under different tax regimes. The model also estimates the foregone revenue as a percentage of capital investment. Total tax expenditures associated with investment in the oil sands are projected to total $820 million for the period from 1986 to 2030, representing 4.6 per cent of the total investment. 10 refs., 2 tabs., 7 figs

  12. Bituminous sands : tax issues

    International Nuclear Information System (INIS)

    Patel, B.

    2004-01-01

    This paper examined some of the tax issues associated with the production of bitumen or synthetic crude oil from oil sands. The oil sands deposits in Alberta are gaining more attention as the supplies of conventional oil in Canada decline. The oil sands reserves located in the Athabasca, Cold Lake and Peace River areas contain about 2.5 trillion barrels of highly viscous hydrocarbons called bitumen, of which nearly 315 billion barrels are recoverable with current technology. The extraction method varies for each geographic area, and even within zones and reservoirs. The two most common extraction methods are surface mining and in-situ extraction such as cyclic steam stimulation (CSS); low pressure steam flood; pressure cycle steam drive; steam assisted gravity drainage (SAGD); hot water flooding; and, fire flood. This paper also discussed the following general tax issues: bituminous sands definition; bituminous sands leases and Canadian development expense versus Canadian oil and gas property expense (COGPE); Canadian exploration expense (CEE) for surface mining versus in-situ methods; additional capital cost allowance; and, scientific research and experimental development (SR and ED). 15 refs

  13. Description of Pintomyia (Pifanomyia falcaorum sp. n. (Diptera: Psychodidae: Phlebotominae, a Fossil Sand Fly from Dominican Amber

    Directory of Open Access Journals (Sweden)

    Reginaldo Peçanha Brazil

    2002-06-01

    Full Text Available A new species of sand fly, Pintomyia (Pifanomyia falcaorum is described from an amber originated from the northern mountain range of Dominican Republic. The male sand fly specimen is well preserved and most features used in Phlebotominae taxonomy are seen with remarkable clarity.

  14. Review of Historic Parishes of England and Wales: An Electronic Map of Boundaries before 1850 with a Gazetteer and Metadata.

    OpenAIRE

    Thomas Pickles

    2002-01-01

    According to the authors, Historic Parishes of England and Wales aims to provide one possible solution to 'a major lacuna militating against the effective exploitation of many post-medieval to mid-Victorian historical sources collected by local administrative areas.' That is 'the lack of information on the boundaries of those administrative areas: the so-called "historic" or "ancient" parishes of England and Wales.' There is no doubt that this is indeed a problem, and that such informatio...

  15. Sand Dunes with Frost

    Science.gov (United States)

    2004-01-01

    9 May 2004 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a suite of frost-covered sand dunes in the north polar region of Mars in early spring, 2004. The dunes indicate wind transport of sand from left to right (west to east). These landforms are located near 78.1oN, 220.8oW. This picture is illuminated by sunlight from the lower left and covers an area about 3 km (1.9 mi) across.

  16. Sand (CSW4)

    CSIR Research Space (South Africa)

    Estuarine and Coastal Research Unit

    1982-12-01

    Full Text Available This report is one of a series on Cape Estuaries being published under the general title "The Estuaries of the Cape, Part 2". The report provides information on sand estuary: historical background, abiotic and biotic characteristics. It is pointed...

  17. Inland drift sand landscapes

    NARCIS (Netherlands)

    Fanta, J.; Siepel, H.

    2010-01-01

    Man has had a complex relationship with inland drift sands through the ages. For some centuries these landscapes were seen as a threat to society, especially agriculture and housing. At present we conserve these landscapes as important Natura 2000 priority habitats. In this book you may find these

  18. Cultural Resources Survey of Three Iberville Parish Levee Enlargement and Revetment Construction Items

    Science.gov (United States)

    1993-09-22

    elm (Ulmus), and pecan (Carya illlnoensis) may occur at higher elevations. Poison ivy (Rhus radicans), Virginia and trumpet creeper (Parthenocissus sp... pecans were produced In the parish. Cotton, grown during the early 1900s, had all but disappeared by 1940. Soybeans, initially planted with corn to...Holland and England are known as de Equivalents in Italy , Iberia, and Mexico are called muioica. Tin glazed earthenware has a soft porous paste

  19. Fusion of arkosic sand by intrusive andesite

    Science.gov (United States)

    Bailey, Roy A.

    1954-01-01

    An andesite dike in the Valles Mountains of northern New Mexico has intruded and partly fused arkosic sediments for a distance of 50 feet from its contacts. The dike is semi-circular in form, has a maximum width of about 100 feet, and is about 500 feet long. Small associated arcuate dikes are arranged in spiral fashion around the main dike, suggesting that they were intruded along shear fractures similar to those described by Burbank (1941). The fused rocks surrounding the andesite dike are of three general types: 1) partly fused arkosic sand, 2) fused clay, and 3) hybrid rocks. The fused arkosic sand consists of relict detrital grains of quartz, orthoclose, and plagioclase, imbedded in colorless glass containing microlites of tridymite, cordierite, and magnetite. The relict quartz grains are corroded and embayed by glass; the orthoclase is sanidinized and partly fused; and the plagioclase is inverted to the high temperature form and is partly fused. The fused clay, which was originally a mixture of montmorillonite and hydromica, consists primarily of cordierite but also contains needle-like crystals of sillimanite (?) or mullite (?). The hybrid rocks originated in part by intermixing of fused arkosic sediments and andesitic liquid and in part by diffusion of mafic constituents through the fused sediments. They are rich in cordierite and magnetite and also contain hypersthene, augite, and plagioclase. The composition of pigeonite in the andesite indicates that the temperature of the andesite at the time of intrusion probably did not exceed 1200?C. Samples of arkosic sand were fused in the presence of water in a Morey bomb at 1050?C. Stability relations of certain minerals in the fused sand suggest that fusion may have taken place at a lower temperature, however, and the fluxing action of volatiles from the andesite are thought to have made this possible.

  20. On Pluvial Compaction of Sand

    DEFF Research Database (Denmark)

    Jacobsen, Moust

    At the Institute of Civil Engineering in Aalborg model tests on dry sand specimens have been carried out during the last five years. To reduce deviations in test results, the sand laying technique has been carefully studied, and the sand mass spreader constructed. Preliminary results have been...

  1. Environmental Impacts of Sand Exploitation. Analysis of Sand Market

    Directory of Open Access Journals (Sweden)

    Marius Dan Gavriletea

    2017-06-01

    Full Text Available Sand is an indispensable natural resource for any society. Despite society’s increasing dependence on sand, there are major challenges that this industry needs to deal with: limited sand resources, illegal mining, and environmental impact of sand mining. The purpose of this paper is twofold: to present an overview of the sand market, highlighting the main trends and actors for production, export and import, and to review the main environmental impacts associated with sand exploitation process. Based on these findings, we recommend different measures to be followed to reduce negative impacts. Sand mining should be done in a way that limits environmental damage during exploitation and restores the land after mining operations are completed.

  2. Research for the development of the crushed sand (II)

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chul Whan; Kang, Sun Duck; Min, Jeong Sik; Synn, Joong Ho; Park, Chan [Korea Institute of Geology Mining and Materials, Taejon (Korea)

    1998-12-01

    The sand obtained from river is not sufficient in amount for the demand of construction industry. The production of sand from sea and mountain is rapidly increasing for the substitution of the river sand. The industry of the crushed sand has recently been bricked for the above. Crushing, classification and dewatering are the main processes in the crushed sand production. This report concentrates the improvement of classification technology and the quality of ready mixed concrete. Air separator with testing size for the classification in the process of dry system was developed by the Yeung Nam university. This plant has the excellent efficiency for the collection of fine powder, but needs the improvement for separating function. The collection efficiency of the testing size air separator is reached to 99% in the condition of high revolution and low feeding speed. The classification efficiency is checked about 50% maximum in the condition of 200 rpm and dry sample. Energy saving test was carried out in the production process of the dry system with the rock samples of 14-17% of water content. The classification efficiency for dewatering sample passed the heating process was analysed 91.5%. But that for high water content sample skipped the heating process was analysed more or less 77%. Even though the heating process causes the classification efficiency being high, the energy consumption can also cause the price of the crushed sand high. Water content of sample as the effective element for the optimization of classification efficiency and energy saving should be studied next year. The quality of crushed sand in the mixing design. The test was carried out with the various content in mixing, the strength of ready mixed concrete has the maximum for the mould with 50-60% content of crushed sand. This strength is higher by 5-30% than 30% content and by 20-32% than 0% content, which means that the industry has the possibility of progress. (author). 10 refs., 31 tabs., 49

  3. Oil sands supply outlook

    International Nuclear Information System (INIS)

    Dunbar, R.

    2004-01-01

    In March 2004, The Canadian Energy Research Institute released a report on the expected future supply from Alberta's oil sands. The report indicates that the future for the already well-established oil sands industry is promising, particularly given the outlook for oil prices. The challenges facing the industry include higher industry supply costs and the need for innovative commercial and technological solutions to address the risks of irregularities and changes in crude oil prices. In 2003, the industry produced 874 thousand barrels per day of synthetic crude oil and unprocessed crude bitumen. This represents 35 per cent of Canada's total oil production. Current production capacity has increased to 1.0 million barrels per day (mbpd) due to new projects. This number may increase to 3.5 mbpd by 2017. Some new projects may be deferred due to the higher raw bitumen and synthetic crude oil supply costs. This presentation provided supply costs for a range of oil sands recovery technologies and production projections under various business scenarios. tabs., figs

  4. Liquefaction resistance of calcareous sands

    International Nuclear Information System (INIS)

    Sandoval Vallejo, Eimar

    2012-01-01

    Calcareous sands are unique in terms of their origin, mineralogy, shape, fragility and intra particle porosity. This article presents results from an experimental program carried out to study the liquefaction resistance of a calcareous sand retrieved from Cabo Rojo at Puerto Rico. The experimental program included mineralogical characterization, index properties, and undrained cyclic triaxial tests on isotropically consolidated reconstituted samples. Due to the large variation in the calcareous sand properties, results are compared with previous researches carried out on other calcareous sands around the world. Results showed a wide range in the liquefaction resistance of the studied calcareous sands. Cabo Rojo sand experienced greater liquefaction resistance than most of the calcareous sands used for comparison. Important differences in the excess pore pressure generation characteristics were also found.

  5. Booming Sand Dunes

    Science.gov (United States)

    Vriend, Nathalie

    "Booming" sand dunes are able to produce low-frequency sound that resembles a pure note from a music instrument. The sound has a dominant audible frequency (70-105 Hz) and several higher harmonics and may be heard from far distances away. A natural or induced avalanche from a slip face of the booming dune triggers the emission that may last for several minutes. There are various references in travel literature to the phenomenon, but to date no scientific explanation covered all field observations. This thesis introduces a new physical model that describes the phenomenon of booming dunes. The waveguide model explains the selection of the booming frequency and the amplification of the sound in terms of constructive interference in a confined geometry. The frequency of the booming is a direct function of the dimensions and velocities in the waveguide. The higher harmonics are related to the higher modes of propagation in the waveguide. The experimental validation includes quantitative field research at the booming dunes of the Mojave Desert and Death Valley National Park. Microphone and geophone recordings of the acoustic and seismic emission show a variation of booming frequency in space and time. The analysis of the sensor data quantifies wave propagation characteristics such as speed, dispersion, and nonlinear effects and allows the distinction between the source mechanism of the booming and the booming itself. The migration of sand dunes results from a complicated interplay between dune building, wind regime, and precipitation. The morphological and morphodynamical characteristics of two field locations are analyzed with various geophysical techniques. Ground-penetrating radar images the subsurface structure of the dunes and reveal a natural, internal layering that is directly related to the history of dune migration. The seismic velocity increases abruptly with depth and gradually increases with downhill position due to compaction. Sand sampling shows local

  6. Variation by Age in Parish Involvement Scores of Catholic Church Attenders in Australia, New Zealand and the United States: Age Effect or Generational Effect?

    Science.gov (United States)

    Dixon, Robert

    2006-01-01

    This article examines levels of involvement of weekly church attenders in Catholic parishes in Australia, New Zealand and the United States through an analysis of data from the International Congregational Life Survey. Factor analysis was used to identify four questionnaire items related to parish involvement which were then combined to produce a…

  7. Oil sands development update

    International Nuclear Information System (INIS)

    1999-01-01

    A detailed review and update of oil sands development in Alberta are provided covering every aspect of the production and economic aspects of the industry. It is pointed out that at present oil sands account for 28 per cent of Canadian crude oil production, expected to reach 50 per cent by 2005. Based on recent announcements, a total of 26 billion dollars worth of projects are in progress or planned; 20 billion dollars worth of this development is in the Athabasca area, the remainder in Cold Lake and other areas. The current update envisages up to 1,800,000 barrels per day by 2008, creating 47,000 new jobs and total government revenues through direct and indirect taxes of 118 billion dollars. Provinces other than Alberta also benefit from these development, since 60 per cent of all employment and income created by oil sands production is in other parts of Canada. Up to 60 per cent of the expansion is for goods and services and of this, 50 to 55 per cent will be purchased from Canadian sources. The remaining 40 per cent of the new investment is for engineering and construction of which 95 per cent is Canadian content. Aboriginal workforce by common consent of existing operators matches regional representation (about 13 per cent), and new developers are expected to match these standards. Planned or ongoing development in environmental protection through improved technologies and optimization, energy efficiency and improved tailings management, and active support of flexibility mechanisms such as emission credits trading, joint implementation and carbon sinks are very high on the industry's agenda. The importance of offsets are discussed extensively along with key considerations for international negotiations, as well as further research of other options such as sequestration, environmentally benign disposal of waste, and enhanced voluntary action

  8. St. Bernard Parish : la crise d’un territoire suburbain St. Bernard Parish, the crisis of a suburban territory

    Directory of Open Access Journals (Sweden)

    Jean-Marc Zaninetti

    2009-04-01

    Full Text Available Situé à l’est de La Nouvelle-Orléans, St. Bernard Parish est l’un des territoires les plus vulnérables au risque d’ondes de tempêtes de toute la région métropolitaine. Après avoir été ravagée par le cyclone Katrina en 2005, St. Bernard peine à se redresser et montre le plus faible niveau de reprise de toute la région du Golfe du Mexique frappée par Katrina. De plus, la reconstruction est freinée par des polémiques virulentes qui nous rappellent les pires années des tensions raciales des années 1960. Cet article s’intéresse aux relations supposées entre les fragmentations urbaines et la faculté d’adaptation aux risques naturels. L’étude du cas de St. Bernard illustre la force d’inertie des territoires et comment de vieilles querelles ville-banlieue affaiblissent la résilience urbaine.Located east of New Orleans, St. Bernard Parish is one of the most vulnerable parts of the greater New Orleans metropolitan area to storm surges. After having been devastated by Hurricane Katrina in 2005, St. Bernard still struggles to recover from the storm, and displays the lowest recovery level of the entire Katrina-hit Gulf Coast area so far. Moreover, reconstruction is hampered by loud polemics that remind us of the worst years of racial polarization during the 1960’s. This paper explores the possible linkage between urban fragmentations and adaptive capacity to natural hazard. The St. Bernard case-study illustrates the strength of path dependency, and how long-entrenched suburb-central city mistrust hampers urban resilience.

  9. Compressive behavior of fine sand.

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Bradley E. (Air Force Research Laboratory, Eglin, FL); Kabir, Md. E. (Purdue University, West Lafayette, IN); Song, Bo; Chen, Wayne (Purdue University, West Lafayette, IN)

    2010-04-01

    The compressive mechanical response of fine sand is experimentally investigated. The strain rate, initial density, stress state, and moisture level are systematically varied. A Kolsky bar was modified to obtain uniaxial and triaxial compressive response at high strain rates. A controlled loading pulse allows the specimen to acquire stress equilibrium and constant strain-rates. The results show that the compressive response of the fine sand is not sensitive to strain rate under the loading conditions in this study, but significantly dependent on the moisture content, initial density and lateral confinement. Partially saturated sand is more compliant than dry sand. Similar trends were reported in the quasi-static regime for experiments conducted at comparable specimen conditions. The sand becomes stiffer as initial density and/or confinement pressure increases. The sand particle size become smaller after hydrostatic pressure and further smaller after dynamic axial loading.

  10. The Orthodox parish in the Russian Empire as an object of fi scal policy of the secular and ecclesiastical authorities in the late XIX — early XX centuries

    Directory of Open Access Journals (Sweden)

    А. BEGLOV

    2014-04-01

    Full Text Available In the article the system of taxation of Orthodox parishes of the Russian Empire in the late XIX — early XX centuries is reconstructed on the new archival materials and the numerous contributions that the parishes carried out from its own funds in favor of the diocesan institutions and charitable organizations are described. Attempt are made to estimate the number of different charges, which existed in this period (the author now includes over 80 items and their size and severity for the parish budget. In this regard, it is concluded that such deductions in some cases accounted for more than half of the income of the parish churches. The author describes the reasons for turning the formally voluntary fees in favor of charitable institutions in virtually compulsory. It investigates the failed attempts of the Supreme Church leadership to reform the system of parish charges in the early XXth century, in particular, the work of the two synodal committees (active in 1905 under the chairmanship of Archbishop Nikon (Sofi yskiy and in 1909, under the chairmanship of Archbishop Anthony (Khrapovitsky. The author comes to the conclusion that these charges were not the only cause of poverty of many parishes (especially rural parishes in Central Russia, but they weakened the parish as a religious community, for the charges were a pretext for permanent discontent among the parishioners about the parish clergy and diocesan authorities. Not the last role here was played by the fact that the diocesan institutions, which were funded by the parish funds were of an estate character.

  11. Religion y politics. Manuel Sabino Crespo, a Parish Priest from Southern Mexico

    Directory of Open Access Journals (Sweden)

    Ana Carolina Ibarra

    2006-07-01

    Full Text Available Through the figure of Manuel Sabino Crespo, who collaborated with the government Morelos set up in Oaxaca and later joined the insurgent cause; this paper seeks to understand the life of a parish  priest in Southern Mexico and the scope of his intellectual training. Thanks to information obtained  from local and private ecclesiastical libraries, and especially from the reports of Crespo's participation found in the proceedings of the cathedral chapter, we can know the sources and arguments with which the rebels defended their ideas regarding ecclesiastical matters.

  12. Rheological Characterization of Green Sand Flow

    DEFF Research Database (Denmark)

    Jabbaribehnam, Mirmasoud; Spangenberg, Jon; Hovad, Emil

    2016-01-01

    The main aim of this paper is to characterize experimentally the flow behaviour of the green sand that is used for casting of sand moulds. After the sand casting process is performed, the sand moulds are used for metal castings. The rheological properties of the green sand is important to quantif...

  13. Sand, jams and jets

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, H. [James Franck Institute and Department of Physics, University of Chicago (United States)]. E-mail: h-jaeger@uchicago.edu

    2005-12-01

    Granular media are offering new insights into problems in condensed-matter physics and materials science, as Heinrich Jaeger explains. The remarkable properties of granular materials are so familiar that most of us do not even notice them. It is clear, for example, that we cannot walk on water unless the temperature has dropped below freezing. However, we take it for granted that sand will support our weight as if it were a solid, even though it can also be poured like a liquid under the same ambient conditions. From breakfast cereal, sugar and flour to construction materials, mining products and pharmaceuticals, granular media are present everywhere in our daily lives. (U.K.)

  14. Riddle of the sands

    Energy Technology Data Exchange (ETDEWEB)

    Rolheiser, P

    1998-09-01

    A geological model of the Alberta landscape during the period stretching from about 110 million to 100 million years ago during the Cretaceous period when dinosaurs roamed the earth, was sketched. Today, the region contains the Cold Lake oil sands deposit. Imperial Oil began large-scale production at Cold Lake in 1985. The formations within the area are the source of almost half of Imperial Oil`s daily crude oil production and account for one in every 20 barrels of oil produced daily in Canada. The bitumen is produced using cyclic steam stimulation where steam is injected at high pressure into the underground reservoir, fracturing the sandstone and heating the bitumen it holds to thin it so that it can then flow through well bores to the surface. Conventional geological theory suggested that the Cold Lake reservoir was the remains of a prehistoric river delta. In 1994, Imperial Oil established a Cold Lake sequence stratigraphy project to verify this theory. This highly complex project involves volumes of geophysical well-log data from the 2,500 wells at Cold Lake, core samples cut from more than 600 of these wells and microscopic fossilized remains of 100-million-year-old flora extracted from the core samples, and seismic information. The interpreted data helps to create a three-dimensional model of the reservoir`s structure and help define its boundaries. Results have shown that the Cold Lake deposit was created from at least 13 intersecting river beds. Each of the rivers flowed for a few hundred thousand years and deposited sands of varying quality in different layers and patterns. The oil came about 40 million years later after the plant and animal materials containing hydrogen and carbon were broken down by heat and pressure to form oil. 1 fig.

  15. The Alberta oil sands story

    Energy Technology Data Exchange (ETDEWEB)

    1974-01-01

    This report serves as a detailed introduction to the Alberta oil sands and their development. It includes a description of the oil sands deposits, an outline of crude bitumen recovery and upgrading processes, the role of Alberta Energy Company in oil sands development, environmental aspects, manpower requirements for oil sands development, research needs, and further oil sands projects. Presently proven recoverable reserves in the oil sands amount to 26.5 billion bbl of synthetic crude. Production from the Syncrude plant (125,000 bbl/d capacity) is expected to begin in 1977, followed by a Shell Canada operation around 1980. The provincial government will participate in the oil sand industry through its joint venture participation in Syncrude and its 50% share in Alberta Energy Company; the latter company participates in related aspects of the Syncrude project, such as pipelines. The result of Alberta's participation in the industry will mean that, directly or indirectly, the province will realize 60% of the total profits. The job creation potential of oil sands projects is estimated to be extensive, with a direct and indirect work force supported by oil sands activities possibly reaching 180,000 persons by the year 2000. Research needs have been identified, particularly in the area of in-situ thermal recovery technology, and the creation of the Alberta Oil Sands Technology and Research Authority has been authorized in order to meet these needs. Although current reserves are sufficient to support 20-30 synthetic crude plants, a number of factors will limit expansion of the industry. 8 figs., 5 tabs.

  16. 78 FR 30901 - Record of Decision and Wetland/Floodplain Statement of Findings for the W.A. Parish Post...

    Science.gov (United States)

    2013-05-23

    ... pathway. Any areas being temporarily used by whooping cranes during its migration at the time of... evaluated the impacts associated with construction and operation of the proposed Parish PCCS Project, as..., environmental, and financial data from the design, construction, and integrated operation of the CO 2 capture...

  17. A Cultural Resources Survey of Arlington Revetment and LSU Berm Levee Improvement Item, East Baton Rouge Parish Louisiana

    Science.gov (United States)

    1993-07-01

    Light gm Slas 14 14 Lis Smm pmlew aumk Simm Milk glass 1 Modern brown glass I Olive glass _ Tin cm key 11 Shotg cartridge 1 Slate 1 Mortar 1 1 Piece of...Parish, Louisiana. Anthropological Report No. 1. Archaeological Survey and Antiquities Commission, Department of Culture, Recreation and Tourism , Baton

  18. 77 FR 58533 - Notice of Availability of the Draft Environmental Impact Statement for the W.A. Parish Post...

    Science.gov (United States)

    2012-09-21

    ... project would demonstrate the commercial feasibility of a retrofit, commercial-scale CO 2 capture and... up to 250- megawatt equivalent (MWe) flue gas slipstream of the combustion exhaust gases from the... gas exhaust from Unit 8 of NRG's existing W.A. Parish Plant in Thompsons, Texas. The project would be...

  19. Ethnobotany of Indigenous Saraguros: Medicinal Plants Used by Community Healers “Hampiyachakkuna” in the San Lucas Parish, Southern Ecuador

    Directory of Open Access Journals (Sweden)

    José M. Andrade

    2017-01-01

    Full Text Available This paper reports the results of an ethnobotanical survey on the use of medicinal plants by community healers “Hampiyachakkuna” in the San Lucas Parish, province of Loja, Ecuador. A particular ethnic group, the indigenous Saraguros, inhabits this region. This study reports 183 plant species used in 75 different curative therapies by the Saraguro healers.

  20. Ethnobotany of Indigenous Saraguros: Medicinal Plants Used by Community Healers "Hampiyachakkuna" in the San Lucas Parish, Southern Ecuador.

    Science.gov (United States)

    Andrade, José M; Lucero Mosquera, Hernán; Armijos, Chabaco

    2017-01-01

    This paper reports the results of an ethnobotanical survey on the use of medicinal plants by community healers "Hampiyachakkuna" in the San Lucas Parish, province of Loja, Ecuador. A particular ethnic group, the indigenous Saraguros, inhabits this region. This study reports 183 plant species used in 75 different curative therapies by the Saraguro healers.

  1. Ethnobotany of Indigenous Saraguros: Medicinal Plants Used by Community Healers “Hampiyachakkuna” in the San Lucas Parish, Southern Ecuador

    Science.gov (United States)

    Lucero Mosquera, Hernán; Armijos, Chabaco

    2017-01-01

    This paper reports the results of an ethnobotanical survey on the use of medicinal plants by community healers “Hampiyachakkuna” in the San Lucas Parish, province of Loja, Ecuador. A particular ethnic group, the indigenous Saraguros, inhabits this region. This study reports 183 plant species used in 75 different curative therapies by the Saraguro healers. PMID:28744470

  2. Rocky Mountain Spotted Fever

    Science.gov (United States)

    ... with facebook share with twitter share with linkedin Rocky Mountain Spotted Fever Credit: CDC A male cayenne tick, Amblyomma cajennense, ... and New Mexico. Why Is the Study of Rocky Mountain Spotted Fever a Priority for NIAID? Tickborne diseases are becoming ...

  3. Rocky Mountain spotted fever

    Science.gov (United States)

    ... spotted fever on the foot Rocky Mountain spotted fever, petechial rash Antibodies Deer and dog tick References McElligott SC, Kihiczak GG, Schwartz RA. Rocky Mountain spotted fever and other rickettsial infections. In: Lebwohl MG, Heymann ...

  4. Direct Chlorination of Zircon Sand

    International Nuclear Information System (INIS)

    Dwiretnani Sudjoko; Budi Sulistyo; Pristi Hartati; Sunardjo

    2002-01-01

    It was investigated the direct chlorination of zircon sand in a unit chlorination equipment. The process was in semi batch. The product gas was scrubbed in aqueous NaOH. It was search the influence of time, ratio of reactant and size of particle sand to the concentration of Zr and Si in the product. From these research it was found that as the times, ratio of reactant increased, the concentration of Zr increased, but the concentration of Si decreased, while as grain size of zircon sand decreased the concentration of Zr decreased, but the concentration of Si increased. (author)

  5. Oil sands and the environment

    Energy Technology Data Exchange (ETDEWEB)

    Seeley, R. [Shell Canada Ltd., Calgary, AB (Canada). Calgary Research Centre

    2004-07-01

    Oil sands are a significant resource for Alberta and Canada with continuing growth opportunity. There is a need to ensure sustainable development of the oil sands resources from a social, economic and environmental perspective. The industry has succeeded in terms of proven reserves, technology advancements, reduced operating costs, reliability and market accessibility. Some of the major challenges facing the industry include high capital cost, infrastructure, social services and keeping pace with growth. This presentation outlined the proactive measures that the oil sands industry has taken to manage environmental issues such as sulphur dioxide and nitrogen oxide emissions, greenhouse gases, water management and land reclamation. tabs., figs.

  6. Alberta oil sands royalty regime

    International Nuclear Information System (INIS)

    Asgarpour, S.

    2004-01-01

    The long term objective of the Oil Sands Business Unit of Alberta Energy is to pave the way for Alberta's bitumen production to reach 3 million barrels per day by 2020. This presentation described the national government's role in resource development. It was emphasized that since the Crown is the owner of the oil sands resource, it would benefit by providing strategic leadership and by generating a larger royalty base. The oil sands fiscal regime was described with reference to generic royalty, risk sharing, investment, and project economics. Business rule principles were also outlined along with criteria for project expansions. Both upstream and downstream challenges and opportunities were listed. 4 figs

  7. Saltation of non-spherical sand particles.

    Directory of Open Access Journals (Sweden)

    Zhengshi Wang

    Full Text Available Saltation is an important geological process and the primary source of atmospheric mineral dust aerosols. Unfortunately, no studies to date have been able to precisely reproduce the saltation process because of the simplified theoretical models used. For example, sand particles in most of the existing wind sand movement models are considered to be spherical, the effects of the sand shape on the structure of the wind sand flow are rarely studied, and the effect of mid-air collision is usually neglected. In fact, sand grains are rarely round in natural environments. In this paper, we first analyzed the drag coefficients, drag forces, and starting friction wind speeds of sand grains with different shapes in the saltation process, then established a sand saltation model that considers the coupling effect between wind and the sand grains, the effect of the mid-air collision of sand grains, and the effect of the sand grain shape. Based on this model, the saltation process and sand transport rate of non-spherical sand particles were simulated. The results show that the sand shape has a significant impact on the saltation process; for the same wind speed, the sand transport rates varied for different shapes of sand grains by as much as several-fold. Therefore, sand shape is one of the important factors affecting wind-sand movement.

  8. Reclaimability of the spent sand mixture – sand with bentonite – sand with furfuryl resin

    Directory of Open Access Journals (Sweden)

    J. Dańko

    2011-04-01

    Full Text Available Introduction of new binding materials and new technologies of their hardening in casting moulds and cores production requires theapplication of reclamation methods adequate to their properties as well as special devices realizing tasks. The spent sands circulationsystem containing the same kind of moulding and core sands is optimal from the point of view of the expected reclamation results.However, in the face of a significant variability of applied technologies and related to them various reclamation methods, the need - of theobtained reclamation products assessment on the grounds of systematic criteria and uniform bases – arises, with a tendency of indicatingwhich criteria are the most important for the given sand system. The reclaimability results of the mixture of the spent moulding sand withGeko S bentonite and the spent core sand with the Kaltharz 404U resin hardened by acidic hardener 100 T3, are presented in the paper.Investigations were performed with regard to the estimation of an influence of core sands additions (10 –25% on the reclaimed materialquality. Dusts and clay content in the reclaim, its chemical reaction (pH and ignition loss were estimated. The verification of the reclaiminstrumental assessment was performed on the basis of the technological properties estimation of moulding sand with bentonite, where the reclaimed material was used as a matrix.

  9. Namibia : triaxial test on sand

    DEFF Research Database (Denmark)

    Steenfelt, Jørgen S.; Jacobsen, Kim P.

    In connection with a harbour project the friction angle of a fine sand is required. On Friday 13 March 1998 the Danish Geotechnical Institute (DGI) delivered app. 2.5 kg sand for testing at the Geotechnical Engineering Laboratory, Aalborg University. The present Data Report summarises the results...... of two CID, isotropically consolidated, drained triaxial tests carried out according to the instructions in DG1 letter dated 13 March 1998....

  10. Environmental Assessment for decommissioning the Strategic Petroleum Reserve Weeks Island Facility, Iberia Parish, Louisiana

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    The Strategic Petroleum Reserve (SPR) Weeks Island site is one of five underground salt dome crude oils storage facilities operated by the Department of Energy (DOE). It is located in Iberia Parish, Louisiana. The purpose of the proposed action is to decommission the Weeks Island crude oil storage after the oil inventory has been transferred to other SPR facilities. Water intrusion into the salt dome storage chambers and the development of two sinkholes located near the aboveground facilities has created uncertain geophysical conditions. This Environmental Assessment describes the proposed decommissioning operation, its alternatives, and potential environmental impacts. Based on this analyses, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) and has issued the Finding of No Significant Impact (FONSI).

  11. Environmental Assessment for decommissioning the Strategic Petroleum Reserve Weeks Island Facility, Iberia Parish, Louisiana

    International Nuclear Information System (INIS)

    1995-12-01

    The Strategic Petroleum Reserve (SPR) Weeks Island site is one of five underground salt dome crude oils storage facilities operated by the Department of Energy (DOE). It is located in Iberia Parish, Louisiana. The purpose of the proposed action is to decommission the Weeks Island crude oil storage after the oil inventory has been transferred to other SPR facilities. Water intrusion into the salt dome storage chambers and the development of two sinkholes located near the aboveground facilities has created uncertain geophysical conditions. This Environmental Assessment describes the proposed decommissioning operation, its alternatives, and potential environmental impacts. Based on this analyses, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) and has issued the Finding of No Significant Impact (FONSI)

  12. Technology unlocks tar sands energy

    Energy Technology Data Exchange (ETDEWEB)

    Law, C

    1967-09-25

    Tar sand processing technology has been developed primarily in the categories of extraction techniques and in-situ processing. In October, a $235 million venture into tar sand processing will be inspected by visitors from many points on the globe. A synthetic crude of premium quality will be flowing through a 16-in. pipeline from the Tar Island plant site of Great Canadian Oil Sands to Edmonton. This processing plant uses an extractive mining technique. The tar sand pay zone in this area averages approximately 150 ft in thickness with a 50-ft overburden. It has been estimated that the tar sands cannot be exploited when the formation thickness is less than 100 ft and overburden exceeds the same amount. This indicates that extraction techniques can only be used to recover approximately 15% of the tar sand deposits. An in-situ recovery technique developed by Shell of Canada is discussed in detail. In essence it is selective hydraulic fracturing, followed by the injection of emulsifying chemicals and steam.

  13. Sandscape - engaging people in Met Office science through sand sculpture

    Science.gov (United States)

    Liggins, Felicity; Dowell, Ellen; Wardley, Jamie; Jamieson, Claire

    2017-04-01

    In 2015, the Met Office's award-winning outreach programme, designed to inspire the next generation of scientists and engineers, delivered one of its most ambitious and creative activities to date. It explored how scientists and artists can come together to create an engaging experience for young people and families. This activity was called Sandscape. Sandscape is an interactive sand sculpture workshop exploring how weather and climate affect our health. Budding sand sculptors are shown how to fashion elaborate structures from sand and water - creating a landscape with bridges, skyscrapers, forests and factories. As they work, participants are encouraged by the scientists delivering the activity to reflect on what makes a healthy city, considering how the natural and built environments influence air quality and circulation and how this impacts our health. Topics discussed include urban heat islands, air pollution and dispersion modelling, pollen forecasting and predicting the wind-borne spread of animal diseases. Each hour long workshop culminates in a dramatic demonstration that uses dry ice to represent clean air circulating from mountains, along rivers and into cities. Here we present an overview of Sandscape, identify the strengths and challenges of such a collaborative, innovative and playful approach to public engagement and share the results of our evaluation. Sandscape was originally supported by the Met Office and the Wellcome Trust, and produced by Einstein's Garden in collaboration with the Met Office, scientists from the University of Exeter and sand sculptors from Sand in Your Eye. It was first presented in Einstein's Garden at Green Man festival 2015, an independent music and arts festival held annually in Wales, and has since been invited to run at the 2015 Bournemouth Arts By the Sea Festival and Teignmouth's TRAIL Sculpture Festival in the summer of 2016.

  14. Oil sands tailings management project

    Energy Technology Data Exchange (ETDEWEB)

    Godwalt, C. [Alberta WaterSMART, Calgary, AB (Canada); Kotecha, P. [Suncor Energy Inc, Calgary, AB (Canada); Aumann, C. [Alberta Innovates - Technology Futures, Alberta Governement, AB (Canada)

    2010-11-15

    The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

  15. Oil sands tailings management project

    International Nuclear Information System (INIS)

    Godwalt, C.; Kotecha, P.; Aumann, C.

    2010-11-01

    The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

  16. Review of Historic Parishes of England and Wales: An Electronic Map of Boundaries before 1850 with a Gazetteer and Metadata.

    Directory of Open Access Journals (Sweden)

    Thomas Pickles

    2002-11-01

    Full Text Available According to the authors, Historic Parishes of England and Wales aims to provide one possible solution to 'a major lacuna militating against the effective exploitation of many post-medieval to mid-Victorian historical sources collected by local administrative areas.' That is 'the lack of information on the boundaries of those administrative areas: the so-called "historic" or "ancient" parishes of England and Wales.' There is no doubt that this is indeed a problem, and that such information will find a wide potential audience. As they admirably illustrate in the accompanying book, parish boundaries have been some of the most enduring and stable organising units, certainly formed by the thirteenth century and largely unchanged until the nineteenth. However, a series of Victorian parliamentary acts sought to rationalise the parochial pattern, and no national sources exist that record the status quo preceding these changes. Kain and Oliver point to an impressive number of historians of locally compiled sources who would benefit from reliable information on these pre-Victorian boundaries, and their list is by no means exhaustive. The core of the package is a database of 'metadata', intended for use with either Acrobat Reader or Microsoft Excel, which records the character of each administrative unit mapped, and the origins of the evidence for its boundaries. Three CDs contain this database in addition to maps of the 'historic' parish boundaries of England that can be read using Acrobat Reader, with the necessary reader software supplied. A further six CDs contain those same maps saved as three separate interactive layers, to be viewed using Adobe Illustrator but this software is not included.

  17. Archeological Testing at Two Sites Near White Castle, Iberville Parish, Louisiana: 16 IV 147 and 16 IV 149

    Science.gov (United States)

    1988-07-26

    styraciflua), green ash (Fraxinus pennsylvania), nutall oak (Quercus nutalli), water oak (Quercus arkansana), elm (Ulmus), and pecan (Carya illinoensis) may...Cotton production lessened, while rice, corn, fruit and pecans increased (Iberville Parish Planning Board 1945). Livestock breeding increased during the...glazed ware manufactured in France. Similar wares from Holland and England are known as delft. Equivalents in Italy , Iberia, and Mexico are called

  18. Cultural Resources Investigations of the East and West Bayou Sale Tie-In Levee, St. Mary Parish, Louisiana.

    Science.gov (United States)

    1998-10-01

    Mendez , and Tara Bond 1994 Archaeological Data Recovery at Ashland-Belle Helene Plantation (16AN26), Ascension Parish, Louisiana, Volume III... Caro - lina. Miller, Daniel 1987 Material Culture and Mass Consumption. Basil Blackwell, Oxford, UK. Miller, Daniel and Christopher Tilley 1984...Jones, R. Mendez , H. Franks, and T. Bond. Volume 1, pp. II- I - 1 1-40. Submitted to the Louisiana Division of Archaeology, Baton Rouge. Weinstein

  19. 76 FR 28311 - Drawbridge Operation Regulations; Bayou Liberty, Mile 2.0, St. Tammany Parish, Slidell, LA

    Science.gov (United States)

    2011-05-17

    ...,'' and then click on the balloon shape in the ``Actions'' column. If you submit your comments by mail or... St. Tammany Parish. The vertical clearance is 7.59 feet (2.31m) above the 2% flowline, elevation 2.5 feet (0.76m) NAVD 1988. Presently, under 33 CFR 117.469, the draw of the S433 Bridge, mile 2.0, at...

  20. Sands at Gusev Crater, Mars

    Science.gov (United States)

    Cabrol, Nathalie A.; Herkenhoff, Kenneth E.; Knoll, Andrew H.; Farmer, Jack D.; Arvidson, Raymond E.; Grin, E.A.; Li, Ron; Fenton, Lori; Cohen, B.; Bell, J.F.; Yingst, R. Aileen

    2014-01-01

    Processes, environments, and the energy associated with the transport and deposition of sand at Gusev Crater are characterized at the microscopic scale through the comparison of statistical moments for particle size and shape distributions. Bivariate and factor analyses define distinct textural groups at 51 sites along the traverse completed by the Spirit rover as it crossed the plains and went into the Columbia Hills. Fine-to-medium sand is ubiquitous in ripples and wind drifts. Most distributions show excess fine material, consistent with a predominance of wind erosion over the last 3.8 billion years. Negative skewness at West Valley is explained by the removal of fine sand during active erosion, or alternatively, by excess accumulation of coarse sand from a local source. The coarse to very coarse sand particles of ripple armors in the basaltic plains have a unique combination of size and shape. Their distribution display significant changes in their statistical moments within the ~400 m that separate the Columbia Memorial Station from Bonneville Crater. Results are consistent with aeolian and/or impact deposition, while the elongated and rounded shape of the grains forming the ripples, as well as their direction of origin, could point to Ma'adim Vallis as a possible source. For smaller particles on the traverse, our findings confirm that aeolian processes have dominated over impact and other processes to produce sands with the observed size and shape patterns across a spectrum of geologic (e.g., ripples and plains soils) and aerographic settings (e.g., wind shadows).

  1. Mountain Plover [ds109

    Data.gov (United States)

    California Natural Resource Agency — Point locations representing observations of mountain plover (Charadrius montanus) feeding and roosting flocks (and occasional individuals) documented during an...

  2. Banks and Financial Services, The featured data collection is the USGS-LAGIC Coastal Parishes Structures Project. This ongoing project was started in 2009 with the intent to map critical infrastructure in the Coastal Zone. The initial four parishes included Lafourche, Plaquemine, St. , Published in 2011, 1:12000 (1in=1000ft) scale, LSU Louisiana Geographic Information Center (LAGIC).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Banks and Financial Services dataset current as of 2011. The featured data collection is the USGS-LAGIC Coastal Parishes Structures Project. This ongoing project was...

  3. Banks and Financial Services, The featured data collection is the USGS-LAGIC Coastal Parishes Structures Project. This ongoing project was started in 2009 with the intent to map critical infrastructure in the Coastal Zone. The initial four parishes included Lafourche, Plaquemine, St. , Published in 2011, 1:24000 (1in=2000ft) scale, LSU Louisiana Geographic Information Center (LAGIC).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Banks and Financial Services dataset current as of 2011. The featured data collection is the USGS-LAGIC Coastal Parishes Structures Project. This ongoing project was...

  4. Hospitals, The featured data collection is the USGS-LAGIC Coastal Parishes Structures Project. This ongoing project was started in 2009 with the intent to map critical infrastructure in the Coastal Zone. The initial four parishes included Lafourche, Plaquemine, St. , Published in 2011, 1:12000 (1in=1000ft) scale, LSU Louisiana Geographic Information Center (LAGIC).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Hospitals dataset current as of 2011. The featured data collection is the USGS-LAGIC Coastal Parishes Structures Project. This ongoing project was started in 2009...

  5. Hospitals, The featured data collection is the USGS-LAGIC Coastal Parishes Structures Project. This ongoing project was started in 2009 with the intent to map critical infrastructure in the Coastal Zone. The initial four parishes included Lafourche, Plaquemine, St., Published in 2011, 1:12000 (1in=1000ft) scale, LSU Louisiana Geographic Information Center (LAGIC).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Hospitals dataset current as of 2011. The featured data collection is the USGS-LAGIC Coastal Parishes Structures Project. This ongoing project was started in 2009...

  6. Modelling offshore sand wave evolution

    NARCIS (Netherlands)

    Nemeth, Attila; Hulscher, Suzanne J.M.H.; van Damme, Rudolf M.J.

    2007-01-01

    We present a two-dimensional vertical (2DV) flow and morphological numerical model describing the behaviour of offshore sand waves. The model contains the 2DV shallow water equations, with a free water surface and a general bed load formula. The water movement is coupled to the sediment transport

  7. Rheology of oil sands slurries

    Energy Technology Data Exchange (ETDEWEB)

    Chow, R.; Zhou, J. [Alberta Research Council, Edmonton, AB (Canada). Mineral Oil Sands Unit; Wallace, D. [Dean Wallace Consulting Inc., Beaumont, AB (Canada)

    2006-07-01

    This study focused on integrating rheology and colloid science to improve recovery of bitumen in surface mined oil sands. Factors that influence recovery, such as conditions of particle interaction, solids concentration and shear rate, were reviewed. In an effort to understand the rheological behaviour of clay-in-water suspensions, an elaborate procedure was developed to separate an inter-bedded clay layer from a site at Albian Sands Energy Inc. The variables were water chemistry, solids concentration, and shear rate. The research study was conducted at the Alberta Research Council with the support of the CONRAD Extraction Group. A controlled stress rheometer was used to provide the quantitative evaluations of the clay slurry properties. The research results indicate that the viscoelastic properties of the slurry are highly influenced by the shear history of the slurry, solids content, calcium concentration, and sample aging. Shear thinning behaviour was observed in all slurry samples, but the slurry viscosity increased with test time for a given shear rate. In order to classify the slurries, a method was developed to distinguish the gel strength. The slurries were then classified into 3 distinct patterns, including no gel, weak gel and strong gel. The evolution of the experimental protocols were described along with the current stability maps that correlate the domains of the gel strength according to the solids concentration, calcium ion content, and shear rate. It was concluded that the rheological properties of oil sands slurries influence bitumen recovery in commercial surface-mined oil sands operations. tabs., figs.

  8. Geology on a Sand Budget

    Science.gov (United States)

    Kane, Jacqueline

    2004-01-01

    Earth science teachers know how frustrating it can be to spend hundreds of dollars on three-dimensional (3-D) models of Earth's geologic features, to use the models for only a few class periods. To avoid emptying an already limited science budget, the author states that teachers can use a simple alternative to the expensive 3-D models--sand. She…

  9. 3D Survey and instability’s analysis of Romena parish

    Directory of Open Access Journals (Sweden)

    Stefano Bertocci

    2015-01-01

    Full Text Available The Romanesque parish church San Pietro a Romena is located in the municipal district of Pratovecchio, in the Casentino valley. It was built, due to a inscription chiselled on a capital, in 1152 d.C. probably wanted byMatilde di Canossa, who has promoted the construction of a lot of churches in this area. We don’t have many informations about the first church, probably destroyed by an earthquake, event that frequently has hit the valley. We based our research on what the DM 01/2008 requests, so our analysis was made following some steps of knowledge: firstly an accurated research in the archive of the Fiesole diocese, to suppose how the buildinghas evolved during the ages, then a 3D laser scanner survey. Thanks to the accurate point cluod we could draw our sections of the church, integrating the material analysis, the orthophotos and the degradation analysis. In parallel has been developed the stratigraphic analysisof the building, which is useful to understand how it has been costructed and how it has grown, so that a coherent restoration project can be efficiently designed.

  10. Batch and column studies of adsorption of Li, Ni and Br by a reference sand for contaminant transport experiments

    International Nuclear Information System (INIS)

    Seigel, M.D.; Ward, D.B.; Bryan, C.R.

    1995-09-01

    A processed quartz sand (Wedron 510), mined from the St. Peter sandstone, has been characterized by a variety of chemical and physical methods for use as a reference porous media in transport model validation experiments. Wedron 510 sand was used in an intermediate-scale experiment involving migration of Ni, Li and Br through a 6-m high x 3-m diameter caisson. Ni and Li adsorption/desorption, and Li/Ni site-competition experiments yielded information on the importance of the trace mineral phases to adsorption of Li and Ni by the sand. The presence of an iron hydroxide coating similar to goethite on the sand grains is suggested by visual observation and leaching experiments. Kaolinite was identified by SEM and XRD as a significant trace mineral phase in the sand and occurs as small particles coating the sand grains. Quartz, the predominant constituent of the sand by weight, does not appear to contribute significantly to the adsorption properties of the sand. Qualitatively, the adsorption properties of the sand can be adequately modeled as a two-mineral system (goethite and kaolinite). The studies described in this report should provide a basis for understanding transport of Ni, Li and Br through porous media similar to the reference sand. Techniques were developed for obtaining parameter values for surface complexation and kinetic adsorption models for the sand and its mineral components. These constants can be used directly in coupled hydrogeochemical transport codes. The techniques should be useful for characterization of other natural materials and elements in high-level nuclear waste in support of coupled hydrogeochemical transport calculations for Yucca Mountain

  11. Tidal dynamics in the sand motor lagoon

    NARCIS (Netherlands)

    De Vries, S.; Radermacher, M.; De Schipper, M.A.; Stive, M.J.F.

    2015-01-01

    The Sand Motor is a mega-nourishment characterized by a very large sand volume of around 20 million m3 placed along the Dutch coast. The Sand Motor is a pilot project to evaluate the performance of an alternative nourishment strategy with respect to different functions of the coastal system. Within

  12. Advances in global mountain geomorphology

    Science.gov (United States)

    Slaymaker, Olav; Embleton-Hamann, Christine

    2018-05-01

    Three themes in global mountain geomorphology have been defined and reinforced over the past decade: (a) new ways of measuring, sensing, and analyzing mountain morphology; (b) a new emphasis on disconnectivity in mountain geomorphology; and (c) the emergence of concerns about the increasing influence of anthropogenic disturbance of the mountain geomorphic environment, especially in intertropical mountains where population densities are higher than in any other mountain region. Anthropogenically induced hydroclimate change increases geomorphic hazards and risks but also provides new opportunities for mountain landscape enhancement. Each theme is considered with respect to the distinctiveness of mountain geomorphology and in relation to important advances in research over the past decade. The traditional reliance on the high energy condition to define mountain geomorphology seems less important than the presence of unique mountain landforms and landscapes and the distinctive ways in which human activity and anthropogenically induced hydroclimate change are transforming mountain landscapes.

  13. Phase I Marine Archeological Remote Sensing Survey of the Proposed Mississippi River Sand Borrow Sites for the Louisiana Coastal Area Barrier Shoreline Restoration Project, Plaquemines Parish, Louisiana

    Science.gov (United States)

    2008-09-01

    Map 6) is comprised of sixteen magnetic anomalies, designated Ml08, Ml46, Ml69, Ml86, M205, M250 , M263, M265, M280, M284, M289, M300, M305, M318...high amplitudes that range from 133.6 to 4211.1 nT, except Ml69, Ml86. M205, M250 , M263, and M265 that have amplitudes ranging from 24.1 to 56.8 nT...3845173.32 20 M248 B 32 01:10.1 167.8 -M 320372.02 3846568.45 N/A M249 B 32 01:46.2 84.5 D 319642.84 3848381.28 22 M250 B 33 01:11.2 34.9 D 318099.83

  14. METHOD OF PROCESSING MONAZITE SAND

    Science.gov (United States)

    Welt, M.A.; Smutz, M.

    1958-08-26

    A process is described for recovering thorium, uranium, and rare earth values from monazite sand. The monazite sand is first digested with sulfuric acid and the resulting "monazite sulfate" solution is adjusted to a pH of between 0.4 and 3.0, and oxalate anions are added causing precipitation of the thorium and the rare earths as the oxalates. The oxalate precipitate is separated from the uranium containing supernatant solution, and is dried and calcined to the oxides. The thorium and rare earth oxides are then dissolved in nitric acid and the solution is contacted with tribntyl phosphate whereby an organic extract phase containing the cerium and thorium values is obtained, together with an aqueous raffinate containing the other rare earth values. The organic phase is then separated from the aqueous raffinate and the cerium and thorium are back extracted with an aqueous medium.

  15. Yucca Mountain digital database

    International Nuclear Information System (INIS)

    Daudt, C.R.; Hinze, W.J.

    1992-01-01

    This paper discusses the Yucca Mountain Digital Database (DDB) which is a digital, PC-based geographical database of geoscience-related characteristics of the proposed high-level waste (HLW) repository site of Yucca Mountain, Nevada. It was created to provide the US Nuclear Regulatory Commission's (NRC) Advisory Committee on Nuclear Waste (ACNW) and its staff with a visual perspective of geological, geophysical, and hydrological features at the Yucca Mountain site as discussed in the Department of Energy's (DOE) pre-licensing reports

  16. Sea sand for reactive barriers

    International Nuclear Information System (INIS)

    Garcia R, G.; Ordonez R, E.; Ordonez R, En.

    2002-01-01

    Some phosphates have the property to suck in radioactive metals in solution, what it is taken in advance to make reactive barriers which are placed in the nuclear waste repositories. In an effort for contributing to the study of this type of materials, it has been obtained the zirconium silicate (ZrSiO 4 ) and the alpha zirconium hydrogen phosphate (Zr(HPO 4 ) 2H 2 O) starting from sea sand in an easy and economic way. (Author)

  17. Episodic Late Holocene dune movements on the sand-sheet area, Great Sand Dunes National Park and Preserve, San Luis Valley, Colorado, USA

    Science.gov (United States)

    Forman, S. L.; Spaeth, M.; Marín, L.; Pierson, J.; Gómez, J.; Bunch, F.; Valdez, A.

    2006-07-01

    The Great Sand Dunes National Park and Preserve (GSDNPP) in the San Luis Valley, Colorado, contains a variety of eolian landforms that reflect Holocene drought variability. The most spectacular is a dune mass banked against the Sangre de Cristo Mountains, which is fronted by an extensive sand sheet with stabilized parabolic dunes. Stratigraphic exposures of parabolic dunes and associated luminescence dating of quartz grains by single-aliquot regeneration (SAR) protocols indicate eolian deposition of unknown magnitude occurred ca. 1290-940, 715 ± 80, 320 ± 30, and 200-120 yr ago and in the 20th century. There are 11 drought intervals inferred from the tree-ring record in the past 1300 yr at GSDNPP potentially associated with dune movement, though only five eolian depositional events are currently recognized in the stratigraphic record. There is evidence for eolian transport associated with dune movement in the 13th century, which may coincide with the "Great Drought", a 26-yr-long dry interval identified in the tree ring record, and associated with migration of Anasazi people from the Four Corners areas to wetter areas in southern New Mexico. This nascent chronology indicates that the transport of eolian sand across San Luis Valley was episodic in the late Holocene with appreciable dune migration in the 8th, 10-13th, and 19th centuries, which ultimately nourished the dune mass against the Sangre de Cristo Mountains.

  18. Utilizing NASA EOS to Assist in Determining Suitable Planting Locations for Bottomland Hardwood Trees in St. Bernard Parish, Louisiana

    Science.gov (United States)

    Reahard, R. R.; Arguelles, M.; Ewing, M.; Kelly, C.; Strong, E.

    2012-12-01

    St. Bernard Parish, located in southeast Louisiana, is rapidly losing coastal forests and wetlands due to a variety of natural and anthropogenic disturbances (e.g. subsidence, saltwater intrusion, low sedimentation, nutrient deficiency, herbivory, canal dredging, levee construction, spread of invasive species, etc.). After Hurricane Katrina severely impacted the area in 2005, multiple Non-Governmental Organizations (NGOs) have focused not only on rebuilding destroyed dwellings, but on rebuilding the ecosystems that once protected the citizens of St. Bernard Parish. Volunteer groups, NGOs, and government entities often work separately and independently of each other and use different sets of information to choose the best planting sites for restoring coastal forests. Using NASA Earth Observing Systems (EOS), Natural Resource Conservation Service (NRCS) soil surveys, and ancillary road and canal data in conjunction with ground truthing, the team created maps of optimal planting sites for several species of bottomland hardwood trees to aid in unifying these organizations, who share a common goal, under one plan. The methodology for this project created a comprehensive Geographic Information System (GIS) to help identify suitable planting sites in St. Bernard Parish. This included supplementing existing elevation data using Digital Elevation Models derived from LIDAR data, and determining existing land cover in the study area from classified Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) imagery. Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data from a single low-altitude swath was used to assess the health of vegetation over an area near the Mississippi River Gulf Outlet Canal (MRGO) and Bayou La Loutre. Historic extent of coastal forests was also mapped using aerial photos collected between 1952 and 1956. The final products demonstrated yet another application of NASA EOS in the rebuilding and monitoring of coastal ecosystems in

  19. Education and Yucca Mountain

    International Nuclear Information System (INIS)

    Lamont, M.A.

    1995-01-01

    This paper outlines a middle school social studies curriculum taught in Nevada. The curriculum was designed to educate students about issues related to the Yucca Mountain project. The paper focuses on the activities used in the curriculum

  20. Recreational mountain biking injuries.

    Science.gov (United States)

    Aitken, S A; Biant, L C; Court-Brown, Charles M

    2011-04-01

    Mountain biking is increasing in popularity worldwide. The injury patterns associated with elite level and competitive mountain biking are known. This study analysed the incidence, spectrum and risk factors for injuries sustained during recreational mountain biking. The injury rate was 1.54 injuries per 1000 biker exposures. Men were more commonly injured than women, with those aged 30-39 years at highest risk. The commonest types of injury were wounding, skeletal fracture and musculoskeletal soft tissue injury. Joint dislocations occurred more commonly in older mountain bikers. The limbs were more commonly injured than the axial skeleton. The highest hospital admission rates were observed with head, neck and torso injuries. Protective body armour, clip-in pedals and the use of a full-suspension bicycle may confer a protective effect.

  1. Landforms of High Mountains

    Directory of Open Access Journals (Sweden)

    Derek A. McDougall

    2016-05-01

    Full Text Available Reviewed: Landforms of High Mountains. By Alexander Stahr and Ewald Langenscheidt. Heidelberg, Germany: Springer, 2015. viii + 158 pp. US$ 129.99. Also available as an e-book. ISBN 978-3-642-53714-1.

  2. Acute mountain sickness

    Science.gov (United States)

    ... GO About MedlinePlus Site Map FAQs Customer Support Health Topics Drugs & Supplements Videos & Tools Español You Are Here: Home → Medical Encyclopedia → Acute mountain sickness URL of this page: //medlineplus.gov/ency/article/ ...

  3. YUCCA MOUNTAIN SITE DESCRIPTION

    International Nuclear Information System (INIS)

    Simmons, A.M.

    2004-01-01

    The ''Yucca Mountain Site Description'' summarizes, in a single document, the current state of knowledge and understanding of the natural system at Yucca Mountain. It describes the geology; geochemistry; past, present, and projected future climate; regional hydrologic system; and flow and transport within the unsaturated and saturated zones at the site. In addition, it discusses factors affecting radionuclide transport, the effect of thermal loading on the natural system, and tectonic hazards. The ''Yucca Mountain Site Description'' is broad in nature. It summarizes investigations carried out as part of the Yucca Mountain Project since 1988, but it also includes work done at the site in earlier years, as well as studies performed by others. The document has been prepared under the Office of Civilian Radioactive Waste Management quality assurance program for the Yucca Mountain Project. Yucca Mountain is located in Nye County in southern Nevada. The site lies in the north-central part of the Basin and Range physiographic province, within the northernmost subprovince commonly referred to as the Great Basin. The basin and range physiography reflects the extensional tectonic regime that has affected the region during the middle and late Cenozoic Era. Yucca Mountain was initially selected for characterization, in part, because of its thick unsaturated zone, its arid to semiarid climate, and the existence of a rock type that would support excavation of stable openings. In 1987, the United States Congress directed that Yucca Mountain be the only site characterized to evaluate its suitability for development of a geologic repository for high-level radioactive waste and spent nuclear fuel

  4. YUCCA MOUNTAIN SITE DESCRIPTION

    Energy Technology Data Exchange (ETDEWEB)

    A.M. Simmons

    2004-04-16

    The ''Yucca Mountain Site Description'' summarizes, in a single document, the current state of knowledge and understanding of the natural system at Yucca Mountain. It describes the geology; geochemistry; past, present, and projected future climate; regional hydrologic system; and flow and transport within the unsaturated and saturated zones at the site. In addition, it discusses factors affecting radionuclide transport, the effect of thermal loading on the natural system, and tectonic hazards. The ''Yucca Mountain Site Description'' is broad in nature. It summarizes investigations carried out as part of the Yucca Mountain Project since 1988, but it also includes work done at the site in earlier years, as well as studies performed by others. The document has been prepared under the Office of Civilian Radioactive Waste Management quality assurance program for the Yucca Mountain Project. Yucca Mountain is located in Nye County in southern Nevada. The site lies in the north-central part of the Basin and Range physiographic province, within the northernmost subprovince commonly referred to as the Great Basin. The basin and range physiography reflects the extensional tectonic regime that has affected the region during the middle and late Cenozoic Era. Yucca Mountain was initially selected for characterization, in part, because of its thick unsaturated zone, its arid to semiarid climate, and the existence of a rock type that would support excavation of stable openings. In 1987, the United States Congress directed that Yucca Mountain be the only site characterized to evaluate its suitability for development of a geologic repository for high-level radioactive waste and spent nuclear fuel.

  5. Vulnerability of Oyster Resource Users to Ecological Change: Case Study from Terrebonne Parish, Louisiana

    Science.gov (United States)

    Humphries, A.; La Peyre, M.; Hall, S.; Dowty Beech, R.

    2016-02-01

    Knowledge of vulnerability provides the foundation for developing actions that minimize impacts on people while maximizing the sustainability of ecosystem goods and services including fisheries. As a result, it is becoming increasingly important to determine if resource-dependent people are vulnerable to ecological change as anthropogenic and climate-induced stressors affect resources in different ways. In coastal Louisiana, the current era of rapid marsh loss and abrupt environmental variation (e.g., sediment diversions) has the potential to undermine oyster-associated livelihoods for those most vulnerable. To evaluate vulnerability, we examined dimensions of social sensitivity and adaptive capacity using semi-structured interviews with three stakeholder groups in the oyster fishery of Terrebonne Parish, Louisiana. Results indicate that oyster owners/operators are highly dependent, and thus sensitive, to changes in the ecological conditions of the fishery due to high levels of occupational identity; however they are likely adaptable, reflected in their willingness to learn about new practices and evolve over time. In contrast, oyster fishers that do not own any portion of the business in which they operate are bad at coping with change and frequently hold negative or fatalistic views on financial planning. Overall, oyster resource users most vulnerable to ecological change will be those with high levels of stewardship, open-minded values, and a balanced perception of environment, as well as low to moderate levels of personal and financial buffers and trust. These results suggest that resource users with higher sensitivity to change are not necessarily most vulnerable because sensitivity may be offset by adaptive capacity. In other words, while sensitivity may determine the potential impact of a climate- or human-induced ecological change to the oyster fishery, adaptive capacity can be a major influence on what impacts actually eventuate.

  6. Studies in Phlebotomine Sand Flies.

    Science.gov (United States)

    1982-06-30

    Reporte de dos casos de [a ology of a sand fly, P/mlebolomu’,s diabolicuw Hall. in forma anergica difusa. Der matol. Rev. Mex. southwestern -Texas...Contribuiin al estudio de los Phmle- CDC, Veterinary Public Health Notes. USDHEW. bwmwnn de Costa Rica (Diptera, Psychodidae). Tesis. CDC. October. pp. 6- 7...janeiron R. j. 195 pp. the Unrited States (D1)pre ra: Psscfirdidae). j. Ortiz, 1. 1965a. Contribuci~in a! estudio tie los flebor- Partrsirtrl. 30:274-275

  7. Prairie Canal Well No. 1, Calcasieu Parish, Louisiana. Volume 1. Completion and testing. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    The Prairie Canal Company, Inc. Well No. 1, approximately 8 miles south of the city of Lake Charles, Louisiana, was tested through the annulus between 5-1/2 inch casing and 2-3/8 inch tubing. The interval tested was from 14,782 to 14,820 feet. The geological section was the Hackberry Sand, a member of the Oligocene Frio formation. Produced water was injected into a disposal well which was perforated in several Miocene Sands from 3070 to 4600 feet. Original plans were to test a section of the Hackberry sand from 14,976 to 15,024 feet. This primary zone, however, produced a large amount of sand, shale, gravel, and rocks during early flow periods and was abandoned in favor of the secondary zone. Four pressure drawdown flow tests and three pressure buildup tests were conducted during a 12-day period. A total of 36,505 barrels of water was produced. The highest sustained flow rate was approximately 7100 BWPD. The gas-to-water ratio, measured during testing, ranged from 41 to 50 SCF/BBL. There is disagreement as to the saturation value of the reservoir brine, which may be between 43.3 and 49.7 SCF/BBL. The methane content of the flare line gas averaged 88.4 mole percent. The CO/sub 2/ content averaged 8.4 mole percent. Measured values of H/sub 2/S in the gas were between 12 and 24 ppM.

  8. Prairie Canal Well No. 1, Calcasieu Parish, Louisiana. Volume II. Well test data. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    The following are included in appendices: field test data, field non-edited data, raw data, tentative method of testing for hydrogen sulfide in natural gas using length of stain tubes, combined sample log, report on reservoir fluids study, well test analysis, analysis of solids samples from primary zone, chemical analysis procedures, scale and corrosion evaluation, laboratory report on scale deposits, and sand detector strip charts. (MHR)

  9. Galveston Island, Texas, Sand Management Strategies

    Science.gov (United States)

    2016-07-01

    billion m3 of beach quality sand . However, Texas projects to date have not utilized these sources because of transportation costs. The lack of nearby...estimate that the San Luis Pass flood shoal contains approximately 11.8 million yd3 of beach quality sand . However, it is expected that if permits...a source of beach- quality sand . 2. Sand could be intercepted before it reaches the present dry beach. ERDC/CHL TR-16-13 55 3. The volume of

  10. Crushed rock sand – An economical and ecological alternative to natural sand to optimize concrete mix

    Directory of Open Access Journals (Sweden)

    Sanjay Mundra

    2016-09-01

    Full Text Available The study investigates the use of crushed rock sand as viable alternative to Natural River sand that is being conventionally used as fine aggregate in cement concrete. Various mix designs were developed for different grades of concrete based on IS, ACI and British codes using Natural River sand and crushed rock sand. In each case, the cube compressive strength test, and beam flexure tests were conducted. The results of the study show that, the strength properties of concrete using crushed rock sand are nearly similar to the conventional concrete. The study has shown that crushed stone sand can be used as economic and readily available alternative to river sand and can therefore help to arrest the detrimental effects on the environment caused due to excessive mining of river sand.

  11. Mountain Biking Injuries.

    Science.gov (United States)

    Ansari, Majid; Nourian, Ruhollah; Khodaee, Morteza

    With the increasing popularity of mountain biking, also known as off-road cycling, and the riders pushing the sport into extremes, there has been a corresponding increase in injury. Almost two thirds of acute injuries involve the upper extremities, and a similar proportion of overuse injuries affect the lower extremities. Mountain biking appears to be a high-risk sport for severe spine injuries. New trends of injury patterns are observed with popularity of mountain bike trail parks and freeride cycling. Using protective gear, improving technical proficiency, and physical fitness may somewhat decrease the risk of injuries. Simple modifications in bicycle-rider interface areas and with the bicycle (bike fit) also may decrease some overuse injuries. Bike fit provides the clinician with postural correction during the sport. In this review, we also discuss the importance of race-day management strategies and monitoring the injury trends.

  12. Sand dune tracking from satellite laser altimetry

    Science.gov (United States)

    Dabboor, Mohammed

    Substantial problems arise from sand movement in arid and semi-arid countries. Sand poses a threat to infrastructure, agricultural and urban areas. These issues are caused by the encroachment of sand on roads and railway tracks, farmland, towns and villages, and airports, to name a few. Sand movement highly depends on geomorphology including vegetation cover, shape and height of the terrain, and grain size of the sand. However, wind direction and speed are the most important factors that affect efficient sand movement. The direction of the movement depends on the main direction of the wind, but it has been shown that a minimum wind speed is required, e.g. wind gusts, to initiate sand transport. This fact prevents a simple calculation of sand transport from conventional wind data as wind records rarely contain sub-minute intervals masking out any wind gusts. An alternative of predicting sand transport is the direct observation of sand advance by in situ measurements or via satellite. Until recently, satellite imagery was the only means to compare dune shape and position for predicting dune migration over several years. In 2003, the NASA laser altimetry mission ICESat became operational and monitors elevations over all surface types including sand dunes with an accuracy of about 10-20 cm. In this study, ICESat observations from repeat tracks (tracks overlapping eachother within 50 m) are used to derive sand dune advance and direction. The method employs a correlation of the elevation profiles over several dunes and was sucessfully validated with synthetic data. The accuracy of this method is 5 meters of dune advance. One of the most active areas exhibiting sand and dune movement is the area of the Arabian Peninsula. Approximately one-third of the Arabian Peninsula is covered by sand dunes. Different wind regimes (Shamal, Kaus) cause sand dune movement in the selected study area in the eastern part of the Arabian Peninsula between 20-25 degrees North and 45-55 degrees

  13. Submarine sand ridges and sand waves in the eastern part of the China Sea

    Science.gov (United States)

    Wu, Ziyin; Li, Shoujun; Shang, Jihong; Zhou, Jieqiong; Zhao, Dineng; Liang, Yuyang

    2016-04-01

    Integrated with multi-beam and single-beam echo sounding data, as well as historical bathymetric data, submarine bathymetric maps of the eastern part of the China Sea, including the Bohai Sea, Huanghai Sea, and East China Sea, are constructed to systematically study submarine sand ridges and sand waves in the eastern part of the China Sea, combined with high-resolution seismic, sub-bottom profile and borehole data. Submarine sand ridges are extraordinarily developed in the eastern part of the China Sea, and 7 sand ridge areas can be divided from north to south, that is, the Laotieshan Channel sand ridge area in the Bohai Sea, the Korea Bay sand ridge area in the southern Huanghai Sea, the sand ridge area in the eastern Huanghai islands and the Huanghai Troughs, the Jianggang sand ridge area in the western Huanghai Sea, the sand ridge area in the East China Sea shelf, and the sand ridge and sand wave area in the Taiwan Strait and Taiwan Banks. The distribution area of the sand ridges and sand waves covers more than 450,000 km2, wherein ~10,000 km2 in the Bohai Bay, ~200,000 km2 in the Huanghai Sea, ~200,000 km2 in the East China Sea shelf, and ~40,000 km2 in the Taiwan Strait and Taiwan Banks, respectively. The great mass of sand ridges are distributed within water depth of 5-160 m, with a total length of over 160 km and a main width of 5-10 km. The inner structure of the sand ridges presents features of high-angle inclined beddings, with main lithology of sands, sand-mud alternations partly visible, and a small number of mud cores. Dating results indicate that the sand ridges in the eastern part of the China Sea are mainly developed in the Holocene. Sea-level variation dominates the sand ridge evolution in the eastern part of the China Sea since the LGM, and the sand ridges developed in the area of < 60m water depth are appeared in bad activity, meanwhile sand ridges with good activity are still developed in large scale.

  14. Mineral resources of the Swasey Mountain and Howell Peak Wilderness Study Areas, Millard County, Utah

    Energy Technology Data Exchange (ETDEWEB)

    Lindsey, D.A.; Zimbelman, D.R.; Campbell, D.L.; Duval, J.S.; Cook, K.L.; Podwysocki, M.H.; Brickey, D.W.; Yambrick, R.A.; Tuftin, S.E.

    1989-01-01

    The Swasey Mountain and the Howell Peak Wilderness Study Areas are underlain by an east-dipping sequence of carbonate rocks, shale, and quartzite of Cambrian age. The Sand Pass mineralized area, immediately northwest of the Swasey Mountain Wilderness Study Area, contains numerous occurrences of jasperoid, small igneous intrusions of Tertiary age, and geochemical anomalies; the mineralized area has been explored for gold. Although no identified resources of metals are known in or near the wilderness study areas, the distribution of geologic structures and stream-sediment geochemical anomalies indicates there is a moderate potential for undiscovered resources of lead, zinc, copper, molybdenum, silver, and gold. An area of moderate potential for undiscovered resources of these metals extends south and east into the Swasey Mountain Wilderness Study Area from the Sand Pass mineralized area. A second area of moderate potential for undiscovered resources of these metals extends from the southern part of the Swasey Mountain Wilderness Study Area across the western part of the Howell Peak Wilderness Study Area. Both study areas contain inferred subeconomic resources of quartzite, high-purity limestone, and sand and gravel. Both areas have moderate resource potential for high-purity limestone and dolomite. Fossils, especially trilobites, of interest to collectors are present in both areas. The potential for undiscovered resources is moderate for oil and gas and is low for geothermal energy within the study areas. There is no potential for undiscovered resources of coal.

  15. Fuel options for oil sands

    International Nuclear Information System (INIS)

    Wise, T.

    2005-01-01

    This presentation examined fuel options in relation to oil sands production. Options include steam and hydrogen (H 2 ) for upgrading; natural gas by pipeline; bitumen; petroleum coke; and coal. Various cost drivers were also considered for each of the fuel options. It was noted that natural gas has high energy value but the capital cost is low, and that coke's energy value is very low but the capital cost is high. A chart forecasting energy prices was presented. The disposition of Western Canada's northern gas situation was presented. Issues concerning rail transportation for coal were considered. Environmental concerns were also examined. A chart of typical gas requirements for 75,000 B/D oil sands projects was presented. Issues concerning steam generation with gas and mining cogeneration with gas fuel and steam turbines were discussed, as well as cogeneration and H 2 with gas fuels and steam turbines. Various technology and fuel utility options were examined, along with details of equipment and processes. Boiler technologies were reviewed by type as well as fuel and steam quality and pressure. Charts of cogeneration with gas turbine and circulation fluid bed boilers were presented. Gasification processes were reviewed and a supply cost basis was examined. Cost drivers were ranked according to energy, operating considerations and capital investment. Results indicated that fuel costs were significant for gas and coal. Capital costs and capital recovery charge was most significant with coal and gasification technology. Without capital recovery, cash costs favour the use of bitumen and coke. Gasification would need lower capital and lower capital recovery to compete with direct burning. It was concluded that direct burning of bitumen can compete with natural gas. With price volatility anticipated, dual fuel capability for bitumen and gas has merit. Petroleum coke can be produced or retrieved from stockpiles. Utility supply costs of direct burning of coke is

  16. Study of Morphologic Change in Poyang Lake Basin Caused by Sand Dredging Using Multi-temporal Landsat Images and DEMs

    Science.gov (United States)

    Qi, S.; Zhang, X.; Wang, D.; Zhu, J.; Fang, C.

    2014-11-01

    Sand dredging has been practiced in rivers, lakes, harbours and coastal areas in recent years in China mostly because of demand from construction industry as building material. Sand dredging has disturbed aquatic ecosystems by affecting hydrological processes, increasing content of suspended sediments and reducing water clarity. Poyang Lake, connecting with Yangtze River in the lower reaches of the Yangtze River, is the largest fresh water lake in China. Sand dredging in Poyang Lake has been intensified since 2001 because such practice was banned in Yangtze River and profitable. In this study, the morphologic change caused by sand dredging in Poyang Lake basin was analysed by overlaying two DEMs acquired in 1952 and 2010 respectively. Since the reflectance of middle infrared band for sand dredging vessel is much higher than that of water surface, sand dredging vessels were showed as isolated grey points and can be counted in the middle infrared band in 12 Landsat images acquired in flooding season during 2000~2010. Another two Landsat images (with low water level before 2000 and after 2010) were used to evaluate the morphologic change by comparing inundation extent and shoreline shape. The following results was obtained: (1) vessels for sand dredging are mainly distributed in the north of Poyang Lake before 2007, but the dredging area was enlarged to the central region and even to Gan River; (2) sand dredging area reached to about 260.4 km2 and is mainly distributed in the north of Songmen Mountain and has been enlarged to central of Poyang Lake from the distribution of sand vessels since 2007. Sand dredged from Poyang Lake was about 1.99 × 109 m3 or 2448 Mt assuming sediment bulk density of 1.23 t m-3. It means that the magnitude of sand mining during 2001-2010 is almost ten times of sand depositions in Poyang Lake during 1955-2010; (3) Sand dredging in Poyang Lake has alternated the lake capacity and discharge section area, some of the watercourse in the

  17. Understanding Colombian Amazonian white sand forests

    NARCIS (Netherlands)

    Peñuela-Mora, M.C.

    2014-01-01

    Although progress has been made in studies on white sand forests in the Amazon, there is still a considerable gap in our knowledge of the unique species composition of white sand forests and their structure and dynamics, especially in Western Amazon. This thesis aims to fill this gap by addressing

  18. Characterization of sand lenses embedded in tills

    DEFF Research Database (Denmark)

    Kessler, Timo Christian; Klint, K.E.S.; Nilsson, B.

    2012-01-01

    Tills dominate large parts of the superficial sediments on the Northern hemisphere. These glacial diamictons are extremely heterogeneous and riddled with fractures and lenses of sand or gravel. The frequency and geometry of sand lenses within tills are strongly linked to glaciodynamic processes...

  19. Japan's involvement in oil sands development

    International Nuclear Information System (INIS)

    Sugiura, T.

    1994-01-01

    According to Japanese national policy, exploration and development by Japanese companies in overseas countries are promoted in order to ensure stable oil supplies. Japan Canada Oil Sands Limited (JACOS), part of the JAPEX group, was established during the 1978 world oil crisis to explore and develop Canadian oil sand resources in accordance with Japan's national policy. The JAPEX group, including JACOS, has invested $123 million in oil sands projects in Alberta. JAPEX's first involvement in oil sands was in the Primrose Project operated by Norcen in the Cold Lake area. Five years of cyclic steam stimulation pilot tests did not produce sufficiently good results to justify further operation. The second involvement was the PCEJ Project, a joint effort by four companies that are participating in a bitumen recovery test project in the Athabasca Deposit. JACOS holds 2,452 km 2 of oil sands leases in Alberta. Tests conducted since 1978 in the PCEJ Project include multiwell steam injection pilot tests, some of which showed promise. JACOS is also participating in steam assisted gravity drainage projects and in federal/provincial research programs. Obstacles identified in developing Alberta oil sands are the lack of a bitumen pipeline to Edmonton and the insufficient length of oil sands leases (currently 10 years), given the difficulties of oil sand development. 10 figs

  20. Seasonal fluctuations of phlebotomines sand fly populations ...

    African Journals Online (AJOL)

    An entomological survey of phlebotomine sand flies was conducted in the Moulay Yacoub province, central Morocco. An anthropic niche (Ouled Aid) and a wild niche (Zliligh) were selected. Sand flies were collected twice a month between April 2011 and March 2012, using sticky traps and CDC light traps. 3675 specimens ...

  1. On shelterbelt design for combating sand invasion.

    NARCIS (Netherlands)

    Mohammed, A.E.; Stigter, C.J.; Adam, H.S.

    1996-01-01

    After a review of the scarce literature on using trees against sand encroachment, a quantitative experiment with a wide shelterbelt to combat sand invasion is reported on. Experimental work was carried out at the northwestern border of the Gezira Scheme (Sudan), an area of severe land degradation

  2. Design of dry sand soil stratified sampler

    Science.gov (United States)

    Li, Erkang; Chen, Wei; Feng, Xiao; Liao, Hongbo; Liang, Xiaodong

    2018-04-01

    This paper presents a design of a stratified sampler for dry sand soil, which can be used for stratified sampling of loose sand under certain conditions. Our group designed the mechanical structure of a portable, single - person, dry sandy soil stratified sampler. We have set up a mathematical model for the sampler. It lays the foundation for further development of design research.

  3. Pattern formation - Instabilities in sand ripples

    DEFF Research Database (Denmark)

    Hansen, J. L.; v. Hecke, M.; Haaning, A.

    2001-01-01

    Sand ripples are seen below shallow wavy water and are formed whenever water oscillates over a bed of sand. Here we analyse the instabilities that can upset this perfect patterning when the ripples are subjected to large changes in driving amplitude or frequency, causing them to deform both...

  4. Flowability in crushed sand mortar

    Directory of Open Access Journals (Sweden)

    Cabrera, O. A.

    2010-12-01

    Full Text Available The present experimental study explored the relationship between mortar flowability and the voids content in crushed sand to determine the effect of grain shape and surface texture as well as dust content on the behaviour of fresh mortar. The findings revealed a close correlation between voids content and the volume of paste needed for mortar to begin to flow as a continuous material, mortar flowability and the water content needed to attain a given flowability. The comparison of the empirical findings to the results obtained with the Larrard (1, 2 model provided further information on the effect of sand grain morphology on fresh mortars.

    En el presente trabajo se plantea un estudio experimental de la fluidez de morteros basado en el contenido de vacíos de arenas machacadas, para comprender la influencia de la forma y textura superficial de los granos de arena y del contenido de polvo de las mismas sobre el estado fresco de morteros. Los resultados muestran la estrecha relación entre el contenido de vacíos entre granos y los volúmenes de pasta necesarios para iniciar el escurrimiento como un material continuo, la fluidez de los morteros, el contenido de agua para alcanzar una determinada fluidez, etc. El comportamiento evaluado se compara con resultados obtenidos aplicando el modelo de F. de Larrard (1, 2, permitiendo de este modo obtener mayor información de la influencia de la morfología de los granos de la arena sobre el estado fresco de los morteros.

  5. Sand transportation and reverse patterns over leeward face of sand dune

    Science.gov (United States)

    Jiang, Hong; Dun, Hongchao; Tong, Ding; Huang, Ning

    2017-04-01

    Sand saltation has complex interactions with turbulent flow and dune form. Most models of wind-blown sand consider ideal circumstances such as steady wind velocity and a flat surface, and the bulk of data on wind flow and sand transport over an individual dune has focused mostly on the influence of dune shape or inter-dune space on the wind flow, neglecting the effect of morphology on sand saltation, particularly airflow and sand transportation over the leeward slope. Wind flow structures over the leeward slope of sand dunes have a fundamental influence on the organization of sand dunes. In order to understand sand dune dynamics, lee face airflow and sediment transportation should be paid more attention. Previous field observations could not measure turbulent flow structure well because of the limited observation points and the influence of experiment structure on wind field. In addition, the reverse sand particles over leeward face could not be collected by sand trap in field. Numerous field observations could not measure turbulent flow structure because of the limited observation points and the influence of experimental structures on the wind field. In addition, the reverse transport of sand particles over leeward face could not be collected by sand traps in field. Therefore, this paper aims to investigate the turbulent flow structure and sand transport pattern over the leeward slope. A numerical model of sand saltation over slope terrain is constructed, which also considers the coupling effects between air flow and sand particles. The large eddy simulation method is used to model turbulent flow. Sand transport is simulated by tracking the trajectory of each sand particle. The results show that terrain significantly alters the turbulent air flow structure and wind-blown sand movement, especially over the leeward slope. Here, mass flux increases initially and then decreases with height in the reversed flow region in the direction of wind flow, and the mass flux

  6. Developing new markets for oil sands products

    International Nuclear Information System (INIS)

    Crandall, G.

    2004-01-01

    This paper presents a review by Purvin and Gertz of western Canadian crude oil supply. This energy consulting firm provides advise to the energy sector. It suggests that oil sands production will surpass declining conventional production. Oil sands supply includes bitumen, synthetic crude oil (SCO), and diluent. It is forecasted that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. The potential of Alberta's oil sands was discussed along with a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. The author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. 15 figs

  7. Numerical simulation of aeolian sand ripples

    International Nuclear Information System (INIS)

    Kang Liqiang; Guo Liejin

    2004-01-01

    With a new horizontal saltation displacement vector, a model is implemented to simulate the initiation and evolution of aeolian sand ripples. In the model, saltation distance considers the effects of surface height and slope. A linear stability analysis is also carried out for formation of sand ripples. The results show that, the model can be able to successfully reproduce sand ripples which can increase in scale by merging of small ripples. The linear stability analysis indicates that sand ripples appear when the relaxation rate parameter is below a threshold value and wind strength parameter is larger than a critical value. The results also verified that the formation of sand ripples is a self-organization process

  8. Mountain-Plains Curriculum.

    Science.gov (United States)

    Mountain-Plains Education and Economic Development Program, Inc., Glasgow AFB, MT.

    The document lists the Mountain-Plains curriculum by job title (where applicable), including support courses. The curriculum areas covered are mathematics skills, communication skills, office education, lodging services, food services, marketing and distribution, welding support, automotive, small engines, career guidance, World of Work, health…

  9. Injuries in mountain biking.

    Science.gov (United States)

    Gaulrapp, H; Weber, A; Rosemeyer, B

    2001-01-01

    Despite still growing attraction mountain biking as a matter of sports traumatology still lacks relevant data based on large cross-sectional surveys. To obtain an overview of risk factors, types, and main body sites of injuries occurring in mountain biking we assessed the results of a questionnaire answered by 3873 athletes. A total of 8133 single lesions were reported by 3474 athletes, 36% of whom regularly participated in competitions. The incidence of injuries in mountain biking is comparable to that in other outdoor sports, the majority of injuries being minor. Mountain biking athletes were found to have an overall injury risk rate of 0.6% per year and 1 injury per 1000 h of biking. The main risk factors included slippery road surface, cyclist's poor judgement of the situation, and excessive speed, representing personal factors that could be altered by preventive measures. Of all injuries 14% were due to collision with some part of the bike, especially the pedals and the handlebar. While 75% of the injuries were minor, such as skin wounds and simple contusions, 10% were so severe that hospitalization was required. A breakdown of the injuries according to body site and frequency of occurrence is presented.

  10. Rocky Mountain Riparian Digest

    Science.gov (United States)

    Deborah M. Finch

    2008-01-01

    The Rocky Mountain Riparian Digest presents the many facets of riparian research at the station. Included are articles about protecting the riparian habitat, the social and economic values of riparian environments, watershed restoration, remote sensing tools, and getting kids interested in the science.

  11. Rocky Mountain High.

    Science.gov (United States)

    Hill, David

    2001-01-01

    Describes Colorado's Eagle Rock School, which offers troubled teens a fresh start by transporting them to a tuition- free campus high in the mountains. The program encourages spiritual development as well as academic growth. The atmosphere is warm, loving, structured, and nonthreatening. The article profiles several students' experiences at the…

  12. Mountains: top down.

    Science.gov (United States)

    Woodwell, George M

    2004-11-01

    Mountainous regions offer not only essential habitat and resources, including water, to the earth's more than 6 billion inhabitants, but also insights into how the global human habitat works, how it is being changed at the moment as global climates are disrupted, and how the disruption may lead to global biotic and economic impoverishment. At least 600 million of the earth's more than 6 billion humans dwell in mountainous regions. Such regions feed water into all the major rivers of the world whose valleys support most of the rest of us. At least half of the valley dwellers receive part or all of their water from montane sources, many from the melt water of glaciers, others from the annual snow melt. Glaciers are retreating globally as the earth warms as a result of human-caused changes in the composition of the atmosphere. Many are disappearing, a change that threatens municipal water supplies virtually globally. The warming is greatest in the higher latitudes where the largest glaciers such as those of Greenland and the Antarctic Continent have become vulnerable. The melting of ice in the northern hemisphere raises serious concerns about the continued flow of the Gulf Stream and the possibility of massive climatic changes in Scandinavia and northern Europe. Mountains are also biotic islands in the sea life, rich in endemism at the ecotype level. The systematic warming of the earth changes the environment out from under these genetically specialized strains (ecotypes) which are then maladapted and vulnerable to diseases of all types. The process is systematic impoverishment in the pattern conspicuous on mountain slopes with increasing exposure to climatic extremes. It is seen now in the increased mortality and morbidity of plants as climatic changes accumulate. The seriousness of the global climatic disruption is especially clear in any consideration of mountains. It can and must be addressed constructively despite the adamancy of the current US administration.

  13. County and Parish Boundaries, MFRDC has city limit boundaries for all municipalities in Dooly, Crisp, Macon, Taylor, Schley, Marion and Webster counties., Published in 2008, 1:63360 (1in=1mile) scale, Middle Flint Regional Development Commission.

    Data.gov (United States)

    NSGIC Regional | GIS Inventory — County and Parish Boundaries dataset current as of 2008. MFRDC has city limit boundaries for all municipalities in Dooly, Crisp, Macon, Taylor, Schley, Marion and...

  14. County and Parish Boundaries, This was created and maintained by Johnson County Records and Tax Administration and is updated when changes occur to county boundaries, Published in 2007, Johnson County Government.

    Data.gov (United States)

    NSGIC Local Govt | GIS Inventory — County and Parish Boundaries dataset current as of 2007. This was created and maintained by Johnson County Records and Tax Administration and is updated when changes...

  15. Characterization and recovery proposal of polymer mortar coating plates of the parish of San Pablo in Seville

    Directory of Open Access Journals (Sweden)

    V. Flores-Alés

    2017-06-01

    Full Text Available This paper deals with the study of the facade elements of the parish of San Pablo in Seville (1961. They are made with polymer mortar. A characterization of the coating plates was carried out and possible solutions for recovering the altered material were analyzed in order to facilitate a future intervention. The resins used as a binder were identified as aliphatic polyester. The resin study was carried out to assure the compatibility of restoration products. Materials characterization provides information about the structural capacity of the plates and the properties achieved. The plates’ colorimetric control is an inexcusable necessity, since any action on the surface of the pieces leads to a color change. All the analyses and testing carried out have led to the creation of an appropriate treatment system for recovery of the plates that provides sufficient information to the intervention project managers to justify decision-making.

  16. Regional transport of a chemically distinctive dust: Gypsum from White Sands, New Mexico (USA)

    Science.gov (United States)

    White, Warren H.; Hyslop, Nicole P.; Trzepla, Krystyna; Yatkin, Sinan; Rarig, Randy S.; Gill, Thomas E.; Jin, Lixin

    2015-03-01

    The White Sands complex, a National Monument and adjoining Missile Range in southern New Mexico, occupies the dry bed of an ice-age lake where an active gypsum dunefield abuts erodible playa sediments. Aerosols entrained from White Sands are sometimes visible on satellite images as distinct, light-colored plumes crossing the Sacramento Mountains to the east and northeast. The IMPROVE network (Interagency Monitoring of PROtected Visual Environments) operates long-term aerosol samplers at two sites east of the Sacramento range. In recent years a spring pulse of sulfate aerosol has appeared at these sites, eclipsing the regional summer peak resulting from atmospheric reactions of sulfur dioxide emissions. A significant fraction of this spring sulfate is contributed by gypsum and other salts from White Sands, with much of the sulfur in coarse particles and concentrations of calcium and strontium above regional levels. The increase in these gypsiferous species coincides with a drought following a period of above-average precipitation. White Sands and the IMPROVE samplers together provide a natural laboratory: a climatically sensitive dust source that is both well characterized and chemically distinct from its surroundings, with a signature that remains identifiable at long-term observatories 100-200 km downwind.

  17. W.A. Parish Post Combustion CO2 Capture and Sequestration Project Final Public Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Armpriester, Anthony [Petra Nova Parish Holdings, Washington, DC (United States)

    2017-02-17

    The Petra Nova Project is a commercial scale post-combustion carbon dioxide capture project that is being developed by a joint venture between NRG Energy (NRG) and JX Nippon Oil and Gas Exploration (JX). The project is designed to separate and capture carbon dioxide from an existing coal-fired unit's flue gas slipstream at NRG's W.A. Parish Generation Station located southwest of Houston, Texas. The captured carbon dioxide will be transported by pipeline and injected into the West Ranch oil field to boost oil production. The project, which is partially funded by financial assistance from the U.S. Department of Energy will use Mitsubishi Heavy Industries of America, Inc.'s Kansai Mitsubishi Carbon Dioxide Recovery (KM-CDR(R)) advanced amine-based carbon dioxide absorption technology to treat and capture at least 90% of the carbon dioxide from a 240 megawatt equivalent flue gas slipstream off of Unit 8 at W.A. Parish. The project will capture approximately 5,000 tons of carbon dioxide per day or 1.5 million tons per year that Unit 8 would otherwise emit, representing the largest commercial scale deployment of post-combustion carbon dioxide capture at a coal power plant to date. The joint venture issued full notice to proceed in July 2014 and when complete, the project is expected to be the world's largest post-combustion carbon dioxide capture facility on an existing coal plant. The detailed engineering is sufficiently complete to prepare and issue the Final Public Design Report.

  18. Critical State of Sand Matrix Soils

    Science.gov (United States)

    Marto, Aminaton; Tan, Choy Soon; Makhtar, Ahmad Mahir; Kung Leong, Tiong

    2014-01-01

    The Critical State Soil Mechanic (CSSM) is a globally recognised framework while the critical states for sand and clay are both well established. Nevertheless, the development of the critical state of sand matrix soils is lacking. This paper discusses the development of critical state lines and corresponding critical state parameters for the investigated material, sand matrix soils using sand-kaolin mixtures. The output of this paper can be used as an interpretation framework for the research on liquefaction susceptibility of sand matrix soils in the future. The strain controlled triaxial test apparatus was used to provide the monotonic loading onto the reconstituted soil specimens. All tested soils were subjected to isotropic consolidation and sheared under undrained condition until critical state was ascertain. Based on the results of 32 test specimens, the critical state lines for eight different sand matrix soils were developed together with the corresponding values of critical state parameters, M, λ, and Γ. The range of the value of M, λ, and Γ is 0.803–0.998, 0.144–0.248, and 1.727–2.279, respectively. These values are comparable to the critical state parameters of river sand and kaolin clay. However, the relationship between fines percentages and these critical state parameters is too scattered to be correlated. PMID:24757417

  19. Invasive plants on disturbed Korean sand dunes

    Science.gov (United States)

    Kim, Kee Dae

    2005-01-01

    The sand dunes in coastal regions of South Korea are important ecosystems because of their small size, the rare species found in this habitat, and the beautiful landscapes they create. This study investigated the current vegetative status of sand dunes on three representative coasts of the Korean peninsula, and on the coasts of Cheju Island, and assessed the conditions caused by invasive plants. The relationships between the degree of invasion and 14 environmental variables were studied. Plots of sand dunes along line transects perpendicular to the coastal lines were established to estimate vegetative species coverage. TWINSPAN (Two-Way Indicator Species Analysis), CCA (Canonical Correspondence Analysis), and DCCA (Detrended Canonical Correspondence Analysis) were performed to classify communities on sand dunes and assess species composition variation. Carex kobomugi, Elymus mollis, and Vitex rotundifolia were found to be the dominant species plotted on the east, the west, and the peripheral coasts of Cheju Island, respectively. Vegetation on the south coast was totally extinct. The 19 communities, including representative C. kobomugi, C. kobomugi- Ixeris repens, C. kobomugi- Oenothera biennis, E. mollis, Lolium multiflorum- Calystegia soldanella, and V. rotundifolia- C. kobomugi, were all classified according to TWINSPAN. Oenothera biennis and L. multiflorum were exotics observed within these native communities. CCA showed that invasive native and exotic species distribution was segregated significantly, according to disturbance level, exotic species number, gravel, sand and silt contents, as well as vegetation size. It further revealed that human disturbance can strongly favor the settlement of invasive and exotic species. Restoration options to reduce exotic plants in the South Korean sand dune areas were found to be the introduction of native plant species from one sand dune into other sand dune areas, prohibition of building and the introduction of exotic

  20. A Viennese Project in Valpovo (Croatia. Parish Church of the Immaculate Conception of the Blessed Virgin Mary in Valpovo and Baroque Churches with Two-Bay Naves

    Directory of Open Access Journals (Sweden)

    Horvat-Levaj, Katarina

    2013-10-01

    Full Text Available The Parish Church of the Immaculate Conception of the Virgin Mary in Valpovo (1733–1736, exceptional both in its spatial organization and the design of its exterior, was constructed in specific circumstances in the aftermath of the liberation of Slavonia from the Ottoman occupation. The old lands of Valpovo, with the medieval fort of Morović, were, in accordance with the Habsburg politics, given as a feud to Baron Hilleprand by Charles VI. The baron initiated the construction of a monumental parish church on his estate by commissioning its design in Vienna, as evidenced by the rich archival material on Hilleprand's property housed at the State Archive in Osijek. In keeping with the provenance of its design, the church was built as a monumental structure consisting of a two-bay nave covered with domical vaults and flanked by a narrower semicircular groin-vaulted sanctuary and a facade belfry. The type represented by the church in Valpovo – single-aisled structure with two bays – was a sort of innovation by Johann Lucas von Hildebrandt, inspired by the famous church of San Fedele in Milan (1569 and often used by Hildebrandt in his own church projects built under the patronage of high Austrian nobility, such as the parish church in Seelowitz in Moravia (1722–27 with an integrated facade belfry, or the parish churches in Aspersdorf (1730, Stranzendorf (1733 and Großstelzendorf (1735–37. This architectural type was adopted and further developed by Hildebrandt's contemporaries, especially his immediate follower Franz Anton Pilgram, a Viennese architect whose design for the parish church in Münchendorf (1740 shows great similarity with the Valpovo church, both in its proportions and in the treatment of details. All this is hardly surprising if one keeps in mind the Viennese origin and the courtly status of the commissioner and donor of the parish church in Valpovo. It took more than two decades for the spatial features of this church to

  1. Watching Faults Grow in Sand

    Science.gov (United States)

    Cooke, M. L.

    2015-12-01

    Accretionary sandbox experiments provide a rich environment for investigating the processes of fault development. These experiments engage students because 1) they enable direct observation of fault growth, which is impossible in the crust (type 1 physical model), 2) they are not only representational but can also be manipulated (type 2 physical model), 3) they can be used to test hypotheses (type 3 physical model) and 4) they resemble experiments performed by structural geology researchers around the world. The structural geology courses at UMass Amherst utilize a series of accretionary sandboxes experiments where students first watch a video of an experiment and then perform a group experiment. The experiments motivate discussions of what conditions they would change and what outcomes they would expect from these changes; hypothesis development. These discussions inevitably lead to calculations of the scaling relationships between model and crustal fault growth and provide insight into the crustal processes represented within the dry sand. Sketching of the experiments has been shown to be a very effective assessment method as the students reveal which features they are analyzing. Another approach used at UMass is to set up a forensic experiment. The experiment is set up with spatially varying basal friction before the meeting and students must figure out what the basal conditions are through the experiment. This experiment leads to discussions of equilibrium and force balance within the accretionary wedge. Displacement fields can be captured throughout the experiment using inexpensive digital image correlation techniques to foster quantitative analysis of the experiments.

  2. Sudan challenges the sand dragon.

    Science.gov (United States)

    Tinker, J

    1978-01-01

    Formerly productive areas have become wasteland as the desert advances in the Sudan. To understand how desertification is undermining the very survival of the Sahel, one ecosystem is reviewed in detail here: the gum arabic zone of Kordofan. After cotton, gum arabic is Sudan's largest export, worth from $14-26 million in recent years. In this zone the ecologically balanced cycle of gum gardens, fire, grain crops, and fallow is now breaking down; the 1968-1973 drought having in many areas delivered the final blow. Because of a growing population, the cultivation period is extended, and the soil becomes impoverished. Overgrazing in the fallow period, and the lopping of gum trees for firewood is producing a low return on the gum trees. Without this gum to harvest for cash, farmers must repeatedly replant their subsistence crops until the land becomes useless sand. The Sudanese have recognized the problem earlier than most, and a number of imaginative and practicable pilot projects are already in use: 1) waterpoint management; 2) construction of firebreaks; 3) land threatened by shifting dunes has been enclosed by stockproof fence and afforested with local trees; and 4) shelter belts have been planted around town perimeters where old gum tree stumps have started to sprout and the grass is reseeding itself. Out of these pilot projects, and with the advice of the U.N. Environment Program, the U.N. Development Program, and FAO, the Sudanese have developed a modest $26 million desert encroachment control and rehabilitation program (DECARP).

  3. Sand to Root Transfer of PAHs and PCBs by Carrots Grown on Sand with Pure Substances and Biosolids Amended Sand

    OpenAIRE

    Sablayrolles, Caroline; Montréjaud-Vignoles, Mireille; Silvestre, Jérôme; Patria, Lucie

    2006-01-01

    A study on behaviour of trace organic compounds (Polycyclic Aromatic Hydrocarbons, PAH, and Polychlorinated Biphenyls, PCB) in a sand-plant system has been carried out, with the reclamation of wastewater treatment plant biosolids for agriculture in mind. Carrot plants (Daucus carota) were grown on soilless culture (sand), to provide optimal transfer conditions, in plant containers inside a temperature regulated greenhouse. There were two types of experiment. The trace organic compounds have i...

  4. DOE's Yucca Mountain studies

    International Nuclear Information System (INIS)

    1992-12-01

    This booklet is about the disposal of high-level nuclear waste in the United States. It is for readers who have a general rather than a technical background. It discusses why scientists and engineers thinkhigh-level nuclear waste may be disposed of safely underground. It also describes why Yucca Mountain, Nevada, is being studied as a potential repository site and provides basic information about those studies

  5. Yucca Mountain Milestone

    International Nuclear Information System (INIS)

    Hunt, Rod

    1997-01-01

    The Department of Energy project to determine if the Yucca Mountain site in Nevada is suitable for geologic disposal of high-level nuclear waste reached a major milestone in late April when a 25-foot-diameter tunnel boring machine ''holed through'' completing a five-mile-long, horseshoe-shaped excavation through the mountain. When the cutting-head of the giant machine broke through to daylight at the tunnel's south portal, it ended a 2 1/2-year excavation through the mountain that was completed ahead of schedule and with an outstanding safety record. Video of the event was transmitted live by satellite to Washington, DC, where it was watched by Secretary of Energy Frederico Pena and other high-level DOE officials, signifying the importance of the project's mission to find a repository for high-level nuclear waste and spent nuclear fuel produced by nuclear power plants. This critical undertaking is being performed by DOE's Office of Civilian Radioactive Waste Management (OCRWM). The tunnel is the major feature of the Exploratory Studies Facility (ESF), which serves as an underground laboratory for engineers and scientists to help determine if Yucca Mountain is suitable to serve as a repository for the safe disposal of high-level nuclear waste. Morrison Knudsen's Environmental/Government Group is providing design and construction-management services on the project. The MK team is performing final design for the ESF and viability assessment design for the underground waste repository that will be built only if the site is found suitable for such a mission. In fact, if at anytime during the ESF phase, the site is found unsuitable, the studies will be stopped and the site restored to its natural state

  6. ACUTE MOUNTAIN SICKNESS

    Directory of Open Access Journals (Sweden)

    Jakub Krzeszowiak

    2012-03-01

    Full Text Available This paper presents the most likely pathophysiological causes of the development of acute mountain sickness (AMS, also known as altitude sickness, its pulmonary form i.e. high altitude pulmonary edema (HAPE, and high altitude cerebral edema (HACE. These diseases constitute extraordinary environmental hazards because they are directly connected with low atmospheric pressure, and thus low partial oxygen pressure. The above adverse atmospheric conditions start to affect humans already at an altitude of 2,500 meters above the sea level and, coupled with extreme physical exertion, can quickly lead to respiratory alkalosis, which is not present under any other conditions in the lowlands. Mountaineering above 4,500 m a.s.l. leads to hypoxia of internal organs and, primarily, reduced renal perfusion with all its consequences. The above adverse changes, combined with inadequate acclimatization, can lead to a situation of imminent danger to life and health. This paper describes in detail the consequences of acute mountain sickness, which can ultimately lead to the development of AMS and one of severe forms of HACE and/or HAPE.

  7. experimental studies of sand production from unconsolidated

    African Journals Online (AJOL)

    ES Obe

    aDepartment of Chemical Engineering, University of Lagos, Lagos, Nigeria. bDepartment of Petroleum ... as risk of well failure, erosion of pipelines and surface facilities, sand separa- ... ment, theoretical and numerical analysis have lead to the ...

  8. A study of global sand seas

    Science.gov (United States)

    McKee, Edwin D.

    1979-01-01

    The birth of the idea that led to this publication on "Global Sand Seas" dates back to the late 1920's. At that time I was engaged in a study of the Coconino Sandstone of Arizona's Grand Canyon. Considerable controversy existed then as to whether this sandstone was a subaqueous deposit or was composed of wind-formed dunes. It became apparent that definitive literature was sparse or lacking on types of dunes, global distribution of these types, the mechanics of their development, the precise nature of their internal structure of cross-stratificiation, and the relation of wind systems to these sand forms. Especially lacking were data on criteria that could confidently be used in the recognition of ancient dunes. The common denominator in this publication is eolian sand bodies. Although the book is concerned primarily with desert sand seas, the subject matter is not restricted to deserts; it includes many references to deposits of coastal sand and to sand bodies in humid climates. Nor does the book deal exclusively with dunes, which, according to most definitions, involve mounds or hills. Many references are made to sand sheets, sand stringers, and other types of sand deposits that have no prominent topographic expression. All sand bodies accumulated by the action of wind are discussed. Chapters A-J of this publication are primarily topical. Chapters cover the grain texture, the color, and the structure of modern dunes and other eolian sands. Special treatment is given to the relation of wind data to dune interpretation, the evolution of form in current-deposited sand bodies as determined from experimental studies, and the discriminant analysis technique for differentiating between coastal and inland desert sands. This topical part of the publication also includes an analysis of criteria used in ancient deposits to interpret their eolian genesis and a consideration of economic application of the principles described, including a discussion of potentials and problems

  9. Bioaugmentation of flow-through sand filters

    DEFF Research Database (Denmark)

    Samuelsen, Elin Djurhuus

    for degradation performances in flow-through sand columns, with the aim of identifying a suitable inoculant strain for future environmental applications. Another aim was to identify a suitable genetic marker to monitor phenoxy acid degradation in strain Sphingobium sp. PM2. We were not able to link motility...... and biofilm formation to the strains´ ability to adhere to sand. Nevertheless, a correlation was found between cell surface hydrophobicity and adhesion and overall degradation performances in flow-through sand columns. We identified S phingobium sp. PM2 as a promising inoculant strain, displaying efficient...... MCPA degradation for prolonged periods in flow-through sand columns. In an expression study of catabolic genes with putative roles in phenoxy acid degradation, we observed a marked upregulation of catabolic genes cadA and tfdC upon exposure to MCPA, 2,4-D, dichlorprop and mecoprop in strain PM2, which...

  10. Geotechnical properties of crude oil contaminated sand

    International Nuclear Information System (INIS)

    Puri, V.K.; Das, B.M.; Cook, E.E.; Shin, E.C.

    1994-01-01

    Contamination of soil due to an oil spill influences its subsequent engineering behavior. An investigation was conducted to study the effect of crude oil contamination on compaction characteristics, shear strength, one-dimensional compression, and coefficient of permeability. Water permeability was also determined by using commercial grade motor oils as contaminants. The test results indicate that the compaction characteristics are influenced by oil contamination. The angle of internal friction of sand (based on total stress condition) decreases due to presence of oil within the pore spaces in sand. One dimensional compression characteristics of sand are significantly influenced by oil contamination resulting in a decrease in the value of constrained modulus with increase in the degree of oil contamination compared to the case of dry sand. Water permeability was observed to be a function of the initial viscosity and the degree of saturation due to the contaminating oil

  11. Displacement pile installation effects in sand

    NARCIS (Netherlands)

    Beijer-Lundberg, A.

    2015-01-01

    Installation effects govern the post-installation behaviour of displacement piles in sand. These effects are currently not completely understood. Suitable experimental techniques to model these installation effects include field, laboratory and experimental models. In the current thesis a

  12. Monitoring the vadose zone in fractured tuff, Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Montazer, P.; Weeks, E.P.; Thamir, F.; Yard, S.N.; Hofrichter, P.B.

    1985-01-01

    Unsaturated tuff beneath Yucca Mountain, Nevada, is being evaluated by the US Department of Energy as a host rock for a potential repository for high-level radioactive waste. As part of the Nevada Nuclear Waste Storage Investigations Project of the US Department of Energy, the US Geological Survey has been conducting hydrologic, geologic, and geophysical investigations at Yucca Mountain and the surrounding region to provide data evaluation of the potential suitability of the site. Hydrologic investigations of the unsaturated zone at this site were started in 1982. A 17.5-inch- (44.5-centimeter-) diameter borehole (USW UZ-1) was drilled by the reverse-air vacuum-drilling technique to a depth of 1269 feet (387 meters). This borehole was instrumented at 33 depth levels. At 15 of the levels, 3 well screens were embedded in coarse-sand columns. The sand columns were isolated from each other by thin layers of bentonite, columns of silica flour, and isolation plugs consisting of expansive cement. Thermocouple psychrometers and pressure transducers were installed within the screens and connected to the data-acquisition system at the land surface through thermocouple and logging cables. Two of the screens at each level were equipped with access tubes to allow collection of pore-gas samples. In addition to these instruments, 18 heat-dissipation probes were installed within the columns of silica flour, some of which also had thermocouple psychrometers. 20 refs., 13 figs., 2 tabs

  13. Supercritical solvent extraction of oil sand bitumen

    Science.gov (United States)

    Imanbayev, Ye. I.; Ongarbayev, Ye. K.; Tileuberdi, Ye.; Mansurov, Z. A.; Golovko, A. K.; Rudyk, S.

    2017-08-01

    The supercritical solvent extraction of bitumen from oil sand studied with organic solvents. The experiments were performed in autoclave reactor at temperature above 255 °C and pressure 29 atm with stirring for 6 h. The reaction resulted in the formation of coke products with mineral part of oil sands. The remaining products separated into SARA fractions. The properties of the obtained products were studied. The supercritical solvent extraction significantly upgraded extracted natural bitumen.

  14. Mineral resources of the Muggins Mountains Wilderness Study Area, Yuma County, Arizona

    International Nuclear Information System (INIS)

    Smith, D.B.; Tosdal, R.M.; Pitkin, J.A.; Kleinkopf, M.D.; Wood, R.H.

    1989-01-01

    The Muggins Mountains Wilderness Study Area covers approximately 8,855 acres immediately south of the Yuma Proving Ground. This study area contains sand and gravel, and it has a moderate potential for gold in placer deposits. One small drainage basin along the southeast boundary of this study area has a moderate potential for uranium. This study area has a low potential for geothermal energy and for oil and gas resources

  15. Effect of manufactured sand on the durability characteristics of concrete

    Directory of Open Access Journals (Sweden)

    S. S. SARAVANAN

    2016-12-01

    Full Text Available Concrete is the most sought after material due to increase in construction activities and infrastructural developments. Availability of natural sand is decreasing thereby increase in the cost of construction. In the present work undertaken, an attempt has been made to give an alternative to natural sand. Optimization of replacement of natural sand with manufactured sand in concrete, durability studies such as water absorption, rapid chloride permeability test, sorptivity, acid resistance, alkaline resistance, impact resistance and abrasion resistance of M40 and M50 grades of concrete have been studied with manufactured sand as fine aggregate and compared the results with the conventional sand concrete. The results shows that there is an increase in the durability properties up to 70 % level of replacements of sand with manufactured sand as fine aggregate and for 100 % use of manufactured sand also gives the better durability than the conventional sand concrete.

  16. Studies on various characteristics of concrete structures using crushed sand

    International Nuclear Information System (INIS)

    Mimatsu, Makoto; Sugita, Hideaki; Yonemura, Masataka.

    1985-01-01

    With the recent advances of construction industry, the demands for concrete, hence for aggregate, are rising. The sand as such is in extreme shortage due to the exhaustion of river sand. Under the situation, the recent trends are for the use of crushed sand, i.e. the artificial sand obtained by crushing rocks, which have advantages of stabilized quality and adequate supplies. In building of nuclear power plants requiring large amounts of concrete, the usage of crushed sand is now unavoidable. The following are described : the situation of aggregate in Kyushu. production method of crushed sand and the quality standards, rocks used for crushed stone and sand and the properties, quality survey on crushed sand and the basic tests, characteristic tests of crushed-stone and -sand mixed concrete, the application of crushed sand in structures of the Sendai Nuclear Power Station. (Mori, K.)

  17. Provenance and recycling of Arabian desert sand

    Science.gov (United States)

    Garzanti, Eduardo; Vermeesch, Pieter; Andò, Sergio; Vezzoli, Giovanni; Valagussa, Manuel; Allen, Kate; Kadi, Khalid A.; Al-Juboury, Ali I. A.

    2013-05-01

    This study seeks to determine the ultimate origin of aeolian sand in Arabian deserts by high-resolution petrographic and heavy-mineral techniques combined with zircon U-Pb geochronology. Point-counting is used here as the sole method by which unbiased volume percentages of heavy minerals can be obtained. A comprehensive analysis of river and wadi sands from the Red Sea to the Bitlis-Zagros orogen allowed us to characterize all potential sediment sources, and thus to quantitatively constrain provenance of Arabian dune fields. Two main types of aeolian sand can be distinguished. Quartzose sands with very poor heavy-mineral suites including zircon occupy most of the region comprising the Great Nafud and Rub' al-Khali Sand Seas, and are largely recycled from thick Lower Palaeozoic quartzarenites with very minor first-cycle contributions from Precambrian basement, Mesozoic carbonate rocks, or Neogene basalts. Instead, carbonaticlastic sands with richer lithic and heavy-mineral populations characterize coastal dunes bordering the Arabian Gulf from the Jafurah Sand Sea of Saudi Arabia to the United Arab Emirates. The similarity with detritus carried by the axial Tigris-Euphrates system and by transverse rivers draining carbonate rocks of the Zagros indicates that Arabian coastal dunes largely consist of far-travelled sand, deposited on the exposed floor of the Gulf during Pleistocene lowstands and blown inland by dominant Shamal northerly winds. A dataset of detrital zircon U-Pb ages measured on twelve dune samples and two Lower Palaeozoic sandstones yielded fourteen identical age spectra. The age distributions all show a major Neoproterozoic peak corresponding to the Pan-African magmatic and tectonic events by which the Arabian Shield was assembled, with minor late Palaeoproterozoic and Neoarchean peaks. A similar U-Pb signature characterizes also Jafurah dune sands, suggesting that zircons are dominantly derived from interior Arabia, possibly deflated from the Wadi al

  18. Creating and destroying mountain belts in a sandbox (Invited)

    Science.gov (United States)

    Hernandez, M.

    2009-12-01

    M. Hernandez-1, L. Cruz-1, G. Hilley-1, J. Malinski-1, W.A. Take-2 1-Department of Geological and Environmental Sciences, Stanford University, Stanford, CA 2-Department of Civil Engineering, Queen's University, Kingston, Canada This study uses a new experimental approach to model the kinematic response of the Aconcagua fold-and-thrust belt to erosion using a deforming sand wedge that is eroded according to a fluvial bedrock incision rule. Our objective is to thoroughly examine the impact that erosion may have had on the kinematics of this fold-and-thrust belt and test the applicability of our approach. Our experimental apparatus allows for a variety of boundary conditions to be applied to the wedge, including constant displacement rate, time-varying displacement rate, constant loading, and time-varying loading. This setting also includes three digital cameras that are connected to the apparatus to monitor the top and one side of the experimental sandbox. In this new experimental approach, as we deform the sand wedge, or mountain belt, we select specific time intervals to calculate, using a Matlab code, the topographic slope derived from our erosion rule. We then use a linear laser to project the calculated topographic slope into the sand wedge and remove any excess of sand with a vacuum cleaner. We then let the wedge continue to deform and repeat the above process. After the end of each experiment, we use Particle Image Velocimetry (PIV) techniques to analyze the movement of the sand particles throughout the experiment. The use of PIV requires the images from all three cameras to be corrected due to lens distortion. We use available software, such as Photoshop, to correct and crop the images. The results of our constant-displacement rate experiments indicate, based on geometric comparisons against natural topographic measurements, that our erosional rule could be satisfactorily applied to sandbox simulations. Each of the main deformational stages identified in the

  19. "Christ is the Mountain"

    Directory of Open Access Journals (Sweden)

    Carl Hallencreutz

    1979-01-01

    Full Text Available In this paper the author focuses on the religious function of symbols in the encounter and interaction of Christianity and other religions. Some observations on the religious function of the symbol of the Holy Mountain in different African contexts are presented. These contexts are a traditional Kikuyu religion, b a Christian hymn from Northern Tanzania, and c the New Year's Fiest of the independent Nazaretha Church among Zulu in South Africa. The examples of how the symbol of the holy mountain is used in different religious contexts in Africa are, of course, too limited to provide a basis for far-reaching generalizations on how symbols function religiously in the encounter of Christianity and other religions. However, this kind of analysis can be applied also when studying other encounters of religions inside and outside Africa. The symbol functions both as a carrier of a new religious message and as an indigenous means to appropriate this message locally and give it adequate form in different milieus. The symbols, which most likely have the religious functions are those which are of a general nature; light, way, living water, and which some are tempted to speak of as archetypes. Yet the comparison between the Chagga-hymn to the holy mountain and Shembe's interpretation of the blessing of the New Year's Fiest on Inhlangakozi indicates, that in the encounter of Christianity and other religions it is not only the symbols as such which produce the local appropriation of the new religious message and give it adequate localized form. Not even in the encounter of Christianity and other religions the symbols function religiously without human beings as actors in the historical process.

  20. Human impacts to mountain streams

    Science.gov (United States)

    Wohl, Ellen

    2006-09-01

    Mountain streams are here defined as channel networks within mountainous regions of the world. This definition encompasses tremendous diversity of physical and biological conditions, as well as history of land use. Human effects on mountain streams may result from activities undertaken within the stream channel that directly alter channel geometry, the dynamics of water and sediment movement, contaminants in the stream, or aquatic and riparian communities. Examples include channelization, construction of grade-control structures or check dams, removal of beavers, and placer mining. Human effects can also result from activities within the watershed that indirectly affect streams by altering the movement of water, sediment, and contaminants into the channel. Deforestation, cropping, grazing, land drainage, and urbanization are among the land uses that indirectly alter stream processes. An overview of the relative intensity of human impacts to mountain streams is provided by a table summarizing human effects on each of the major mountainous regions with respect to five categories: flow regulation, biotic integrity, water pollution, channel alteration, and land use. This table indicates that very few mountains have streams not at least moderately affected by land use. The least affected mountainous regions are those at very high or very low latitudes, although our scientific ignorance of conditions in low-latitude mountains in particular means that streams in these mountains might be more altered than is widely recognized. Four case studies from northern Sweden (arctic region), Colorado Front Range (semiarid temperate region), Swiss Alps (humid temperate region), and Papua New Guinea (humid tropics) are also used to explore in detail the history and effects on rivers of human activities in mountainous regions. The overview and case studies indicate that mountain streams must be managed with particular attention to upstream/downstream connections, hillslope

  1. Nuclear energy in the oils sands

    International Nuclear Information System (INIS)

    Arsenault, J.E.

    2014-01-01

    The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

  2. Nuclear energy in the oils sands

    Energy Technology Data Exchange (ETDEWEB)

    Arsenault, J.E.

    2014-09-15

    The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

  3. Comparison between predicted and observed sand waves and sand banks in the North Sea

    NARCIS (Netherlands)

    Hulscher, Suzanne J.M.H.; van den Brink, G.M.

    2001-01-01

    For the first time a prediction model of regular morphological patterns on the seabed was tested against observations of sand wave and sand bank occurrence in the entire North Sea. The model, which originates from first physical principles, predicts this occurrence via two dimensionless parameters

  4. MORPHOMETRIC CHARACTERIZATION OF THE SAND FRACTION IN A SAND GRAIN IMAGE CAPTURE SYSTEM1

    Directory of Open Access Journals (Sweden)

    Lucimar Arruda Viana

    Full Text Available ABSTRACT Morphology studies assume significant importance in analysis of phenomena of granular systems packaging, in particular with a view to the use of the technique of soil stabilization named particle size correction in forest roads. In this context, this study aimed to develop and operationalize a Sand Grain Image Capture System and, hereby, determine the morphological indices of the sand fractions of two sandy soils called João Pinheiro (JP and Cachoeira da Prata (CP. Soil samples, air-dried, were sieved (2.0 mm nominal mesh size for removal of gravels. The materials that passed through the sieve were subjected to dispersion, washing in 0.053 mm nominal mesh size sieve, removal of organic matter and iron oxides to obtain the clean sand fractions. Subsequently, each soil sample was sieved for separation into twelve classes, between the diameters of 0.149 mm and 1.190 mm, using a Rotap shaker. Next, tests were carried out to characterize the morphometric attributes of the twelve classes of sand fractions of the soils studied. For validation of the performance of the Sand Grain Image Capture System, the results were compared to those obtained using a standard procedure for image analysis. The analysis of the results led to the following conclusions: (i the sand fraction of the JP soil presented higher values for the morphometric indices roundness, elongation and compactness compared to sand fraction of the CP soil; and (ii the Sand Grain Image Capture System worked properly, with practicality.

  5. Protected areas in mountains

    Directory of Open Access Journals (Sweden)

    Hamilton, L. S.

    2006-12-01

    Full Text Available

    The importance of a global Protected Areas Network in sustaining appropriate mountain development is presented in this paper. Present status of the world’s “official” Protected Areas in the UN List, and the proportion that are in mountain areas, and including international designations (World Heritage and Biosphere Reserves. Current and future challenges in the management of these special areas are also commented.



    El autor destaca la importancia de una Red Mundial de Espacios Protegidos para el desarrollo sostenible de las montañas. Comenta luego el estatus actual de las Áreas Protegidas “oficiales” del Mundo en la Lista de las Naciones Unidas y qué proporción de ellas forma parte de las montañas, sin olvidar las figuras internacionales de protección como Patrimonio de la Humanidad y Reservas de Biosfera. Para terminar, se discuten los problemas de gestión actuales y futuros de estas áreas tan especiales

  6. SP mountain data analysis

    Science.gov (United States)

    Rawson, R. F.; Hamilton, R. E.; Liskow, C. L.; Dias, A. R.; Jackson, P. L.

    1981-01-01

    An analysis of synthetic aperture radar data of SP Mountain was undertaken to demonstrate the use of digital image processing techniques to aid in geologic interpretation of SAR data. These data were collected with the ERIM X- and L-band airborne SAR using like- and cross-polarizations. The resulting signal films were used to produce computer compatible tapes, from which four-channel imagery was generated. Slant range-to-ground range and range-azimuth-scale corrections were made in order to facilitate image registration; intensity corrections were also made. Manual interpretation of the imagery showed that L-band represented the geology of the area better than X-band. Several differences between the various images were also noted. Further digital analysis of the corrected data was done for enhancement purposes. This analysis included application of an MSS differencing routine and development of a routine for removal of relief displacement. It was found that accurate registration of the SAR channels is critical to the effectiveness of the differencing routine. Use of the relief displacement algorithm on the SP Mountain data demonstrated the feasibility of the technique.

  7. Heavy mineral concentration from oil sand tailings

    Energy Technology Data Exchange (ETDEWEB)

    Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

    2008-07-01

    This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

  8. A Improved Seabed Surface Sand Sampling Device

    Science.gov (United States)

    Luo, X.

    2017-12-01

    In marine geology research it is necessary to obtain a suf fcient quantity of seabed surface samples, while also en- suring that the samples are in their original state. Currently,there are a number of seabed surface sampling devices available, but we fnd it is very diffcult to obtain sand samples using these devices, particularly when dealing with fne sand. Machine-controlled seabed surface sampling devices are also available, but generally unable to dive into deeper regions of water. To obtain larger quantities of seabed surface sand samples in their original states, many researchers have tried to improve upon sampling devices,but these efforts have generally produced ambiguous results, in our opinion.To resolve this issue, we have designed an improved andhighly effective seabed surface sand sampling device that incorporates the strengths of a variety of sampling devices. It is capable of diving into deepwater to obtain fne sand samples and is also suited for use in streams, rivers, lakes and seas with varying levels of depth (up to 100 m). This device can be used for geological mapping, underwater prospecting, geological engineering and ecological, environmental studies in both marine and terrestrial waters.

  9. Sand filter clogging by septic tank effluent.

    Science.gov (United States)

    Spychała, M; Błazejewski, R

    2003-01-01

    The aim of this study was to characterise conditions and factors affecting fine sand clogging by septic tank effluent on the basis of physical modelling. The physical model consisted of 12 sand columns dosed with sewage from one household (5 persons), preliminary treated in a septic tank. Hydraulic loadings of the sand filters were equal to 82 mm/d. The mean discharge from sand columns, measured as the effluent volume collected during 10 minutes, decreased significantly over the experiment period from 34 cm3/min in August 2000 to 20 cm3/min in August 2001 at the same temperature of about 20 degrees C. First the columns clogged almost completely after 480 days in December 2001, however six columns had remained unclogged till the end of the experiment (March 2002). The temperature had a significant impact on hydraulic conductivity. A vertical distribution of accumulated mass and biomass was investigated in partly clogged sand. Microscopic survey of the clogging layer showed a presence of live micro-organisms, residuals of dead micro-organisms, particularly pieces of small animal armour and many fibres. These particles accelerated the accumulation of solids in the upper clogging layer. The study indicated that temperature impact on the filter hydraulic conductivity was more significant for biological activity, than for sewage viscosity.

  10. The behavior of gaseous iodine in sand

    International Nuclear Information System (INIS)

    Takahashi, Kanji

    1974-01-01

    Radioactive iodine gas was passed through 10 different sands collected at rivers and hills. The relation between the amount of the loaded gas and the amount of adsorbed gas was determined at room temperature, 50 -- 60 0 C, and 90 -- 100 0 C under humidity of 2 sand. This amount was about 1 -- 3 times as much as that of monomolecular membrane adsorption, 0.2 -- 0.3 μg/cm 2 . The decrease of adsorption amount that accompanies the increase of humidity is attributable to the decrease of effective surface area of sand due to the presence of water. The transport of iodine in sand was studied by passing gaseous iodine through a glass tubing packed with sand. The distribution in the flow direction of iodine indicated that the ease of desorption depends upon the situation of adsorption. Easily desorbed case was named Henry type adsorption. Hardly desorbed case was named absorption type. Discussion is made on experimental results. (Fukutomi, T.)

  11. Mitigating in situ oil sands carbon costs

    Energy Technology Data Exchange (ETDEWEB)

    Theriault, D.J.; Peterson, J. [Laricina Energy Ltd., Calgary, AB (Canada); Heinrichs, H. [Canadian Chemical Technology Inc., Calgary, AB (Canada)

    2008-10-15

    Carbon capture and sequestration is a complex problem with a variety of dimensions that need to be considered. The political, social, and regulatory pressures are forcing carbon costs on the oil sands industry in an effort to reduce the carbon footprint of oil sands operations. This paper reviewed the political, social, and regulatory pressures and obligations for the in-situ oil sands industry. It presented the views and insights of Laricina Energy on the carbon challenge. It also described the initiatives that Laricina Energy is taking to manage these imperatives and outlined the challenges the industry is facing. The purpose of the paper was to encourage dialogue and collaboration by the oil sands industry. The paper also described the dimensions of the carbon problem and how the industry can contribute to a solution. Last, the paper reviewed the parameters of carbon dioxide or greenhouse gas containment and storage issues. It was concluded that the regulatory and policy requirements need to be clarified so that industry understands the new business landscape as well as the requirements that influence the economics of in-situ oil sands development. 7 refs., 7 figs.

  12. YUCCA MOUNTAIN PROJECT - A BRIEFING -

    International Nuclear Information System (INIS)

    2003-01-01

    This report has the following articles: Nuclear waste--a long-term national problem; Spent nuclear fuel; High-level radioactive waste; Radioactivity and the environment; Current storage methods; Disposal options; U.S. policy on nuclear waste; The focus on Yucca Mountain; The purpose and scope of the Yucca Mountain Project; The approach for permanently disposing of waste; The scientific studies at Yucca Mountain; The proposed design for a repository at Yucca Mountain; Natural and engineered barriers would work together to isolate waste; Meticulous science and technology to protect people and the environment; Licensing a repository; Transporting waste to a permanent repository; The Environmental Impact Statement for a repository; Current status of the Yucca Mountain Project; and Further information available on the Internet

  13. Interpretive geophysical fault map across the central block of Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Ponce, D.A.

    1996-01-01

    Geophysical data collected along 29 traverses across the central block of Yucca Mountain in southwest Nevada reveal anomalies associated with known fault sand indicate a number of possible concealed faults beneath the eastern flank of Yucca Mountain. Geophysical interpretations indicate that Midway Valley is characterized by several known and previously unknown faults, that the existence of the Yucca Wash fault is equivocal, and that the central part of the eastern flank of Yucca Mountain is characterized by numerous low-amplitude anomalies that probably reflect numerous small-scale faults. Gravity and magnetic data also reveal several large-amplitude anomalies that reflect larger-scale faulting along the margins of the central block

  14. European mountain biodiversity

    Directory of Open Access Journals (Sweden)

    Nagy, Jennifer

    1998-12-01

    Full Text Available This paper, originally prepared as a discussion document for the ESF Exploratory Workshop «Trends in European Mountain Biodiversity - Research Planning Workshop», provides an overview of current mountain biodiversity research in Europe. It discusses (a biogeographical trends, (b the general properties of biodiversity, (c environmental factors and the regulation of biodiversity with respect to ecosystem function, (d the results of research on mountain freshwater ecosystems, and (e climate change and air pollution dominated environmental interactions.- The section on biogeographical trends highlights the importance of altitude and latitude on biodiversity. The implications of the existence of different scales over the different levels of biodiversity and across organism groups are emphasised as an inherent complex property of biodiversity. The discussion on ecosystem function and the regulation of biodiversity covers the role of environmental factors, productivity, perturbation, species migration and dispersal, and species interactions in the maintenance of biodiversity. Regional and long-term temporal patterns are also discussed. A section on the relatively overlooked topic of mountain freshwater ecosystems is presented before the final topic on the implications of recent climate change and air pollution for mountain biodiversity.

    [fr] Ce document a été préparé à l'origine comme une base de discussion pour «ESF Exploratory Workshop» intitulé «Trends in European Mountain Biodiversity - Research Planning Workshop»; il apporte une vue d'ensemble sur les recherches actuelles portant sur la biodiversité des montagnes en Europe. On y discute les (a traits biogéographiques, (b les caractéristiques générales- de la biodiversité, (c les facteurs environnementaux et la régulation de la biodiversité par rapport à la fonction des écosystèmes, (d les résultats des études sur les écosystèmes aquatiques des montagnes et (e les

  15. Sand transport, erosion and granular electrification

    DEFF Research Database (Denmark)

    Merrison, J.P.

    2012-01-01

    is expanding our current understanding and outline the areas of advancement needed in the future. Presentation is made of current models for wind driven detachment/entrainment and the transport rates of sand and dust, including the effects of contact induced grain electrification. This ubiquitous phenomenon...... can affect grain transport through the generation of intense electric fields and processes of electrostatic assembly. Importantly the transport of sand is characterized by saltation, which is known to be an active process for erosion and therefore a source for dust and sand formation. Using novel...... erosion simulation techniques the link between grain transport rates and erosion rates has been quantified. Furthermore this can be linked to production rates for dust and has been associated with chemical and mineral alteration through a process of mechanical activation of fractured surfaces. This work...

  16. Thermoluminescent dosimetric properties of Descalvado sand

    International Nuclear Information System (INIS)

    Teixeira, M.I.; Caldas, L.V.E.

    2006-01-01

    Sand samples proceeding from Descalvado, Sao Paulo, were studied with regard to their dosimetric properties using the thermoluminescence technique (TL) for high doses. These sand samples present steady physical and chemical characteristics to the end items, and they are used in the glass industry and for casting. The TL curves of the samples were obtained after an irradiation at the Gamma-Cell system ( 60 Co), of IPEN. The glow curves present two peaks at 80 C and 220 C approximately. Calibration curves were obtained for doses between 50 Gy and 5 kGy. The results indicate that the sand samples can be used for high-doses dosimetry in several areas of applications of ionizing radiation. (Author)

  17. Development tendencies of moulding and core sands

    Directory of Open Access Journals (Sweden)

    Stanislaw M. Dobosz1

    2011-11-01

    Full Text Available Further development of the technology for making moulding and core sands will be strictly limited by tough requirements due to protection of the natural environment. These tendencies are becoming more and more tense, so that we will reach a point when even processes, that from technological point of view fulfill high requirements of the foundry industry, must be replaced by more ecologically-friendly solutions. Hence, technologies using synthetic resins as binding materials will be limited. This paper presents some predictable development tendencies of moulding and core sands. The increasing role of inorganic substances will be noticed, including silicate binders with significantly improved properties, such as improved knock-out property or higher reclamation strength. Other interesting solutions might also be moulding sands bonded by geo-polymers and phosphate binders or salts and also binders based on degradable biopolymers. These tendencies and the usefulness of these binders are put forward in this paper.

  18. Thermoluminescent dosimetric properties of Descalvado sand

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, M.I.; Caldas, L.V.E

    2006-07-01

    Sand samples proceeding from Descalvado, Sao Paulo, were studied with regard to their dosimetric properties using the thermoluminescence technique (TL) for high doses. These sand samples present steady physical and chemical characteristics to the end items, and they are used in the glass industry and for casting. The TL curves of the samples were obtained after an irradiation at the Gamma-Cell system ({sup 60} Co), of IPEN. The glow curves present two peaks at 80 C and 220 C approximately. Calibration curves were obtained for doses between 50 Gy and 5 kGy. The results indicate that the sand samples can be used for high-doses dosimetry in several areas of applications of ionizing radiation. (Author)

  19. Erosion of an ancient mountain range, the Great Smoky Mountains, North Carolina and Tennessee

    Science.gov (United States)

    Matmon, A.; Bierman, P.R.; Larsen, J.; Southworth, S.; Pavich, M.; Finkel, R.; Caffee, M.

    2003-01-01

    Analysis of 10Be and 26Al in bedrock (n=10), colluvium (n=5 including grain size splits), and alluvial sediments (n=59 including grain size splits), coupled with field observations and GIS analysis, suggest that erosion rates in the Great Smoky Mountains are controlled by subsurface bedrock erosion and diffusive slope processes. The results indicate rapid alluvial transport, minimal alluvial storage, and suggest that most of the cosmogenic nuclide inventory in sediments is accumulated while they are eroding from bedrock and traveling down hill slopes. Spatially homogeneous erosion rates of 25 - 30 mm Ky-1 are calculated throughout the Great Smoky Mountains using measured concentrations of cosmogenic 10Be and 26Al in quartz separated from alluvial sediment. 10Be and 26Al concentrations in sediments collected from headwater tributaries that have no upstream samples (n=18) are consistent with an average erosion rate of 28 ?? 8 mm Ky-1, similar to that of the outlet rivers (n=16, 24 ?? 6 mm Ky-1), which carry most of the sediment out of the mountain range. Grain-size-specific analysis of 6 alluvial sediment samples shows higher nuclide concentrations in smaller grain sizes than in larger ones. The difference in concentrations arises from the large elevation distribution of the source of the smaller grains compared with the narrow and relatively low source elevation of the large grains. Large sandstone clasts disaggregate into sand-size grains rapidly during weathering and downslope transport; thus, only clasts from the lower parts of slopes reach the streams. 26Al/10Be ratios do not suggest significant burial periods for our samples. However, alluvial samples have lower 26Al/10Be ratios than bedrock and colluvial samples, a trend consistent with a longer integrated cosmic ray exposure history that includes periods of burial during down-slope transport. The results confirm some of the basic ideas embedded in Davis' geographic cycle model, such as the reduction of relief

  20. Level II Cultural Resource investigation for the Texoma Distribution Enhancements project, Cameron and Calcasieu Parishes, Louisiana: Final report

    Energy Technology Data Exchange (ETDEWEB)

    LeeDecker, C. H.; Holland, C. C.

    1987-10-01

    A Level II Cultural Resource Survey was completed for the Texoma Distribution Enhancements project, located in Cameron and Calcasieu Parishes, Louisiana. The 13-mile pipeline extends from Strategic Petroleum Reserve No. 3 to a terminus near Vincent Landing. Located in Louisiana's southwest coastal zone, the pipeline will traverse extensive marsh lands as well as upland prairie terrace areas. Present land use within the project area consists primarily of undeveloped marsh land and cattle range. The study methods included background research, intensive pedestrian survey with systematic shovel testing, a boat survey, and laboratory analysis of recovered artifact collections. One historic site, 16CU205, was identified during the field survey, and it was tested for National Register eligibility. The site is assignable to the Industrialization and Modernization (1890-1940) Cultural Unit. Archaeological testing indicates that it is a rural residence or farmstead, with a house and one outbuilding within the proposed right-of-way. The site lacks significant historical association and sufficient archaeological integrity to merit inclusion on the National Register of Historic Places. Four standing structures were also identified during the field survey. The structures are agricultural outbuildings, less than 40 years in age, that possess no architectural distinction or historical association. They have been documented photographically and by scaled plan drawings, but do not merit additional study prior to their destruction. 24 refs., 15 figs., 3 tabs.

  1. Sources for the study of the historic organ of the parish of Santa Ines in Zacatelco (Tlaxcala, Mexico

    Directory of Open Access Journals (Sweden)

    Gustavo Mauleón Rodríguez

    2018-01-01

    Full Text Available In this collaboration, we present the results of an investigation into and documentation of a Mexican organ that from several viewpoints can be considered one of the most important in the country. Constructed during the first half of the 19th century for a parish church in the Puebla-Tlaxcala diocese, this relatively large organ is the work of Seferino Agustin Castro an early member of one of the most notable families of organ builders, the Castros, who were based in Puebla de los Ángeles but whose work –much of which survives– also extended significantly into Tlaxcala. Seferino’s life spanned the transition from the Viceroyalty of New Spain to independent Mexico and the organs, while clear products of a long tradition of mechanical-action organs of Spanish/Iberian design, simultaneously reflect new historic, musical, and technological circumstances. Moreover, they display characteristics that can be considered to be uniquely Pueblan and thus mark an important moment in the development of organs in that region.

  2. SOCIAL ACTIVITIES OF PARISH CLERGY IN CIRCUMSTANCES OF GOVERNMENTALIZING OF ORTHODOX CHURCH IN RUSSIAN EMPIRE OF 19 TH CENTURY

    Directory of Open Access Journals (Sweden)

    Светлана Геннадиевна Зубанова

    2014-12-01

    Full Text Available The article deals with the experience of the Russian empire of the 19 th century in creating the conditions for social activities of the Russian Orthodox Church. The author describes such types of the Russian Orthodox Church activities aimed at helping those in need as helping the poor, coordinating the work of poor-houses, collecting donations, supporting parochial schools, poor houses, orphanages, hospitals, construction and reconstruction of churches. The author analyzes the role of the parochial patronages in the charity and social service activities, as well as in the moral and spiritual education of the population. The work of the well-known members of the clergy which forms a part of the Russian Orthodox Church and Russian history in general is given as an example of the above mentioned activities. The article extensively covers the responsibilities of parish priests, the difficulties which they come across, and highlights the reasons for the negative attitude towards the clergy in the late 19 th - early 20 th centuries. The author summarizes the historical lessons of the social activity of the Russian Orthodox Church. The article provides grounds for the opinion that the social activities of the Church should not interfere with its main religious functions, and the partnership of the state and the Russian Orthodox Church in the social projects should contribute to the improvement of people’s life and their moral and spiritual growth.

  3. A Threshold Continuum for Aeolian Sand Transport

    Science.gov (United States)

    Swann, C.; Ewing, R. C.; Sherman, D. J.

    2015-12-01

    The threshold of motion for aeolian sand transport marks the initial entrainment of sand particles by the force of the wind. This is typically defined and modeled as a singular wind speed for a given grain size and is based on field and laboratory experimental data. However, the definition of threshold varies significantly between these empirical models, largely because the definition is based on visual-observations of initial grain movement. For example, in his seminal experiments, Bagnold defined threshold of motion when he observed that 100% of the bed was in motion. Others have used 50% and lesser values. Differences in threshold models, in turn, result is large errors in predicting the fluxes associated with sand and dust transport. Here we use a wind tunnel and novel sediment trap to capture the fractions of sand in creep, reptation and saltation at Earth and Mars pressures and show that the threshold of motion for aeolian sand transport is best defined as a continuum in which grains progress through stages defined by the proportion of grains in creep and saltation. We propose the use of scale dependent thresholds modeled by distinct probability distribution functions that differentiate the threshold based on micro to macro scale applications. For example, a geologic timescale application corresponds to a threshold when 100% of the bed in motion whereas a sub-second application corresponds to a threshold when a single particle is set in motion. We provide quantitative measurements (number and mode of particle movement) corresponding to visual observations, percent of bed in motion and degrees of transport intermittency for Earth and Mars. Understanding transport as a continuum provides a basis for revaluating sand transport thresholds on Earth, Mars and Titan.

  4. Gasification of oil sand coke: review

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E. [IMAF Group, Ottawa, ON (Canada)

    1998-08-01

    The production of synthetic crude from the tar sands in Western Canada has been steadily increasing. Most of the delayed coke produced by Suncor is combusted on site, whereas all fluid coke produced by Syncrude is stockpiled.The database on the chemical and physical properties of the oil sand coke, including the composition and fusion properties of the mineral matter, has been established. The reactivity of the coke was determined by oxygen chemisorption, fixed bed and fluid bed bench scale gasification and pilot plant gasification. The reactivity of the oil sand coke for gasification is rather low and comparable to high rank coals, such as anthracite. Slurrability tests revealed that a solid concentration in water, approaching 70 wt%, can be achieved. Gasification is the front runner among clean technologies for the conversion of carbonaceous solids to useful products. Several commercial gasifiers are available to cover the wide range of severity. Because of the low reactivity of oil sands coke, high severity conditions are required to achieve high gasification conversion. Such conditions can be attained in entrained bed gasifiers. Gasifiers employing both dry and slurry feeding systems are suitable. A high efficiency, low SO{sub x} and NO{sub x} emissions, as well as a low solid waste production are among the key advantages of the gasification technology compared with thecompeting technologies. Commercial gasification of oil sands coke is delayed because of the availability of natural gas on the site of the upgrading plants. Potential for the transportation of the oil sand coke to USA for electricity generation using the integrated gasification combined-cycle (IGCC) technology was evaluated. 27 refs., 17 figs., 9 tabs.

  5. On the Size Distribution of Sand

    DEFF Research Database (Denmark)

    Sørensen, Michael

    2016-01-01

    A model is presented of the development of the size distribution of sand while it is transported from a source to a deposit. The model provides a possible explanation of the log-hyperbolic shape that is frequently found in unimodal grain size distributions in natural sand deposits, as pointed out......-distribution, by taking into account that individual grains do not have the same travel time from the source to the deposit. The travel time is assumed to be random so that the wear on the individual grains vary randomly. The model provides an interpretation of the parameters of the NIG-distribution, and relates the mean...

  6. Creating fluid injectivity in tar sands formations

    Science.gov (United States)

    Stegemeier, George Leo; Beer, Gary Lee; Zhang, Etuan

    2010-06-08

    Methods for treating a tar sands formation are described herein. Methods for treating a tar sands may include heating a portion of a hydrocarbon layer in the formation from one or more heaters located in the portion. The heat may be controlled to increase the permeability of at least part of the portion to create an injection zone in the portion with an average permeability sufficient to allow injection of a fluid through the injection zone. A drive fluid and/or an oxidizing fluid may be provided into the injection zone. At least some hydrocarbons are produced from the portion.

  7. Log-inject-log in sand consolidation

    International Nuclear Information System (INIS)

    Murphy, R.P.; Spurlock, J.W.

    1977-01-01

    A method is described for gathering information for the determination of the adequacy of placement of sand consolidating plastic for sand control in oil and gas wells. The method uses a high neutron cross-section tracer which becomes part of the plastic and uses pulsed neutron logging before and after injection of the plastic. Preferably, the method uses lithium, boron, indium, and/or cadmium tracers. Boron oxide is especially useful and can be dissolved in alcohol and mixed with the plastic ingredients

  8. Oil sand synfuel production using nuclear energy

    International Nuclear Information System (INIS)

    Barnert, H.

    1984-10-01

    The importance of oil sand as a primary energy carrier is illustrated. The oil sand mining project 'synfuel' in Fort McMurray, Alberta, Canada, is described. On the basis of a layout of an In-situ-process different possibilities of introducing nuclear energy to the process are described. This leads to an increase of the product yield, leading finally to a doubling of the energy output compared to the reference layout. The introduction of nuclear energy contributes to the reduction of emissions, in particular to the emission of carbon dioxide in the conversion process. (orig.)

  9. Permeability Tests on Silkeborg Sand No. 0000

    DEFF Research Database (Denmark)

    Lund, Willy; Jakobsen, Kim Parsberg

    on the characteristics of the soil matrix, the permeability is determined for different void ratios. All tests are performed on reconstituted specimens of Silkeborg Sand No. 0000. The permeability is determined by use of a falling head apparatus. The apparatus, test procedures and the analysis method are described......The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends...

  10. Permeability Tests on Eastern Scheldt Sand

    DEFF Research Database (Denmark)

    Jakobsen, Kim Parsberg

    on the characteristics of the soil matrix, the permeability is determined for different void ratios. All tests are performed on reconstituted specimens of Eastern Scheldt Sand. The permeability is determined by use of a falling head apparatus. Finally the test results are briefly summarised and a relationship between......The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends...

  11. Sand control systems used in completing wells

    Directory of Open Access Journals (Sweden)

    Gabriel Wittenberger

    2005-12-01

    Full Text Available Expandable Tubular Technology is transforming the face of well completion and construction. This technology provides: a substantially higher hydrocarbon production rates from the reservoir, a reduced well drilling and construction costs, new possibilities for previously unreachable or uneconomic reservoirs, and step a change towards the single diameter well. ESS (Expandable Sand Screen has an unrivalled performance worldwide for delivering a reliable sand control in a wide range of applications. Well costs typically cut by over 20 %, and the productivity increases up to 70 %.

  12. Geology at Yucca Mountain

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    Both advocates and critics disagree on the significance and interpretation of critical geological features which bear on the safety and suitability of Yucca Mountain as a site for the construction of a high-level radioactive waste repository. Critics believe that there is sufficient geological evidence to rule the site unsuitable for further investigation. Some advocates claim that there is insufficient data and that investigations are incomplete, while others claim that the site is free of major obstacles. We have expanded our efforts to include both the critical evaluations of existing geological and geochemical data and the collection of field data and samples for the purpose of preparing scientific papers for submittal to journals. Summaries of the critical reviews are presented in this paper

  13. The Yucca Mountain tours

    International Nuclear Information System (INIS)

    Shepard, N.F.; Champagne, D.L.

    1992-01-01

    In 1978, Mderthaner et al. observed that opposition to nuclear facilities was lowest near the facility. This suggested that opposition decreased as familiarity with the facility increased, with distance from the facility as an inverse measure of familiarity. In this paper, the authors analyze data from the literature supporting this hypothesis and examine a poll of 1200 public visitors to the candidate repository site at Yucca Mountain, Nevada, in March through June 1991. The tour poll and independent pools show that most Nevadans support the present scientific investigation of the site while opposing the repository. Among the visitors, support for the investigation increased from 66 to 90 percent, which we attribute to increased familiarity

  14. Experimental perforation of tubing with a hydraulic sand jet

    Energy Technology Data Exchange (ETDEWEB)

    Semenov, Yu V

    1970-01-01

    A series of field tests has shown that perforation with a hydraulic sand jet improves the quality of well completion. The sand jet does not crack the cement sheath or the casing, and the perforations are larger and deeper than perforations formed by explosive charges. Fluid circulation during sand jet perforation can safely be stopped for at least 10 min. Water containing a surfactant can be used as a sand carrier. Sand jet perforation allows successful completion of wells cased by 2 tubing strings. Sand jet perforation can be used to clean the borehole well and to remove foreign objects from the well.

  15. MouldingSandDB – a modern database storing moulding sands properties research results

    Directory of Open Access Journals (Sweden)

    J. Jakubski

    2011-01-01

    Full Text Available The complexity of foundry processes requires the use of modern, advanced IT tools for optimization, storage and analysis of t echnicaldata. Properties of moulding and core sands that are collected in research laboratories, manufacturers, and finally in the foundries, are not in use later on. It seems important to create a database that will allow to use the results stored, along with the possibility of searching according to set criteria, adjusted to casting practice. This paper presents part of the database named „MouldingSandDB”, which allows to collect and search data for synthetic moulding sands.

  16. Efficacy of Different Sampling Methods of Sand Flies (Diptera: Psychodidae in Endemic Focus of Cutaneous Leishmaniasis in Kashan District, Isfahan Province, Iran.

    Directory of Open Access Journals (Sweden)

    Marzieh Hesam-Mohammadi

    2014-12-01

    Full Text Available The aim of the study was to evaluate and compare the efficiency and practicality of seven trapping methods for adult phlebotominae sand flies. The results of this investigation provide information to determine the species composition and nocturnal activity pattern of different sand fly species.The study was carried out in both plain region (about 5km far from northeast and mountainous region (about 40km far from southwest of Kashan City. Seven traps were selected as sampling methods and sand flies were collected during 5 interval times starting July to September 2011 and from 8:00PM to 6:00AM in outdoors habitats. The traps include: sticky traps (4 papers for 2 hours, Disney trap, Malaise, CDC and CO2 light traps, Shannon traps (black and white nets and animal-baited trap.A total of 1445 sand flies belonging to 15 species of Phlebotomus spp. and five of Sergentomyia spp. were collected. Females and males comprised 44.91% and 55.09% of catches, respectively. Of the collected specimens, Se. sintoni was found to be the most prevalent (37.86% species, while Ph. papatasi, accounted for 31.76% of the sand flies.Disney trap and sticky traps exhibited the most productivity than other traps. In addition, in terms of the efficiency of sampling method, these two trapping methods appeared to be the most productive for both estimating the number of sand flies and the species composition in the study area.

  17. Undrained Cyclic Behaviour of Dense Frederikshavn Sand

    DEFF Research Database (Denmark)

    Nielsen, Søren Kjær; Ibsen, Lars Bo; Sørensen, Kris Wessel

    2013-01-01

    A modified contour diagram is created for the Frederikshavn Sand in the undrained case for a relative density of ID = 80 %. It can be used to estimate the number of cycles to failure for a given combination of pore pressure, average and cyclic load ratio. The diagram is based on a series of undra...

  18. Radiation safety in Australia's mineral sands industry

    International Nuclear Information System (INIS)

    Hughes, W.

    1989-06-01

    This brochure is part of a training package aiming to explain in simple terms what radiation is, how it affects people's lives and how, in the specific case of the mineral sand industry, the risk of ill-effects from low-level radioactivity could be effectively guarded against by simple and easily followed safety precautions. ills

  19. Geomechanical properties of lime stabilized clayey sands

    International Nuclear Information System (INIS)

    Arabani, M.; Karami, M. Veis

    2007-01-01

    Clayey sands that have low plasticity, low compressibility and high strength under loads, are suitable as a base material for any engineering construction projects as well as for roads and building construction. Decrease of plasticity and compressibility as well as increase in strength of these materials can be obtained by many different methods. Of these methods, lime stabilization is a common, applicable, and easy to use approach that can improve geomechanical and geotechnical properties of clayey sand fills. In this study some important geomechanical properties and geotechnical properties of clayey sands including compressive strength, CBR and elastic plastic behavior are investigated. A range of gradations representative of those gradations found in situ in the north of Iran were selected for testing and samples were artificially rebuilt in the laboratory. The mixes were then stabilized with hydrated lime and cured. Different mechanical tests were performed on mature materials. The stress-strain behavior of lime-stabilized mixes was plotted and a parabolic function was used to estimate the trend of stress-strain behavior. The data show that there is a correlation among the results of uniaxial load test, tensile strength, and CBR of the tested specimens. Also, results of the unconfined compression test and the indirect tensile strength test show that an increase in clay content up to a certain percent, in the clay-sand fills, tends to increase the strength of the materials in compression as well as in tension. (author)

  20. Market opportunities and challenges for oil sands

    International Nuclear Information System (INIS)

    Wise, T.H.

    2004-01-01

    The use of Alberta bitumen as a clean fuel depends on upgrading, transportation, and refining processes. Forecasts show that oil sands production, which includes synthetic crude oil (SCO), will surpass declining conventional production from the Western Canada Sedimentary Basin. The challenges facing the oils sands processing industry include: crude oil prices which affect the producer's market; market expansion options; diluent availability/cost; supply cost competitiveness; and, regional processing. The common market issues include light/heavy crude prices, oil sands crude qualities, prices of oil sands crudes, pipeline infrastructure, and competitive supplies. The issues facing the refiners are: refining margins, security of crude supply, refined product quality, and competitive product supply. It was noted that Alberta must retain or increase its share of the Midwest market. The market expansion options were reviewed for both downstream (refining) and upstream (upgrading) operations. New pipeline capacity is needed to reach more distant markets such as Southern Midwest, Washington, and California. The market is nearly saturated for Canada's heavy oil supply. More upgrading will be required as bitumen production increases. Market growth is still possible for Canada's SCO but according to forecasts, the market could also become saturated. To increase demand and allow supplies to grow, SCO prices may fall below light crude prices. It was noted that a balance must be achieved in order for producers to increase production and for refiner/upgraders to expand their conversion capacity. 13 figs

  1. Growing markets to sustain oil sands development

    International Nuclear Information System (INIS)

    Wise, T.H.

    2003-01-01

    The utilization of Alberta bitumen for the clean fuels market depends on upgrading, transportation, and refining processes. Forecasts show that oil sands production, which includes synthetic crude oil (SCO), will surpass declining conventional production in Western Canada. Several issues pose a challenge to the oil sands processing industry. The producers' market is affected by crude oil prices, market expansion options, diluent availability/cost, supply cost competitiveness, and regional processing. The common market issues include light/heavy crude prices, oil sands crude qualities, prices of oil sands crudes, pipeline infrastructure, and competitive supplies. The issues facing the refiners are: refining margins, security of crude supply, refined product quality, and competitive product supply. A brief review of markets for Canadian crude oil, including synthetic crude, was provided. The share of the Midwest market by Alberta must be retained and increased. The market expansion options were reviewed for both downstream (refining) and upstream (upgrading) operations. To reach more distant markets such as Southern Midwest, Washington, and California, new pipeline capacity would be required. The market is nearly saturated for Canada's heavy oil supply. More upgrading will be required as bitumen production increases. Market growth is still possible for Canada's SCO but according to forecasts, the market could also become saturated. To increase demand and allow supplies to grow, SCO prices may fall below light crude prices. It was noted that a balance must be achieved in order for producers to increase production and for refiner/upgraders to expand their conversion capacity. tabs., figs

  2. Microbial Characterization of Qatari Barchan Sand Dunes.

    Directory of Open Access Journals (Sweden)

    Sara Abdul Majid

    Full Text Available This study represents the first characterization of sand microbiota in migrating barchan sand dunes. Bacterial communities were studied through direct counts and cultivation, as well as 16S rRNA gene and metagenomic sequence analysis to gain an understanding of microbial abundance, diversity, and potential metabolic capabilities. Direct on-grain cell counts gave an average of 5.3 ± 0.4 x 105 cells g-1 of sand. Cultured isolates (N = 64 selected for 16S rRNA gene sequencing belonged to the phyla Actinobacteria (58%, Firmicutes (27% and Proteobacteria (15%. Deep-sequencing of 16S rRNA gene amplicons from 18 dunes demonstrated a high relative abundance of Proteobacteria, particularly enteric bacteria, and a dune-specific-pattern of bacterial community composition that correlated with dune size. Shotgun metagenome sequences of two representative dunes were analyzed and found to have similar relative bacterial abundance, though the relative abundances of eukaryotic, viral and enterobacterial sequences were greater in sand from the dune closer to a camel-pen. Functional analysis revealed patterns similar to those observed in desert soils; however, the increased relative abundance of genes encoding sporulation and dormancy are consistent with the dune microbiome being well-adapted to the exceptionally hyper-arid Qatari desert.

  3. Afyon-Sandıklı

    Indian Academy of Sciences (India)

    δ18O and δD isotope ratios of the Sandıklı waters plot along the continental meteoric water line ... and district heating. Several studies on geology, hydrogeology along ..... precipitation; In: Handbook of Environmental Isotope. Geochemistry ...

  4. Dark grains of sand: a geological storytelling

    Science.gov (United States)

    Gallo Maresca, Magda

    2017-04-01

    In the secondary Italian school the Earth science learning begins at first year, in synergy with other natural science subjects such as Astronomy, Chemistry and Biology. Italian teachers have to focus on the landscape geomorphological aspects and often Earth processes are difficult to display since they are related to certain phenomena happened during the past and often far from the involved country. In order to better understand the environment surrounding us, very simple and poor materials, like sands, allow the teachers to create attractive lab experiences. According to the IBSE (Inquiry Based Science Education) approach, a learning unit has been implemented starting from a walking along the light carbonate beaches of the Adriatic sea: a smart look to the sands ("engage step"), stroke the students fantasy pushing them to explore some strange black grains on the sands. Dirty sands? Or rock landscape, soil degradation and Ofanto river and coastal processes (erosion, transportation and deposition)? This was the teaching challenge. Due to the youngest age, a third level, guided inquiry, was adopted so the teacher is the "guide of inquiry" encouraging the students using the research question ("Why is the sand dark?", "Do all sands look the same?", "Where does it come from?") and driving the students around their investigation plans ("How can I measure grain size?"). A procedure to answer the above questions and validate the results and explanations has been implemented to allow the students to be proactive in their study. During the learning activities will be the students to ask for field trip to elaborate their new knowledge, verify and visualize the speculated processes. The teaching skills allow to address several geosciences domains such as mineralogy, petrology, regional geology and geodynamics as well as other scientific disciplines such as mathematics (more specifically statistics), forensic science and even life sciences (the presence of bioclasts might

  5. The provenance of Taklamakan desert sand

    Science.gov (United States)

    Rittner, Martin; Vermeesch, Pieter; Carter, Andrew; Bird, Anna; Stevens, Thomas; Garzanti, Eduardo; Andò, Sergio; Vezzoli, Giovanni; Dutt, Ripul; Xu, Zhiwei; Lu, Huayu

    2016-03-01

    Sand migration in the vast Taklamakan desert within the Tarim Basin (Xinjiang Uyghur Autonomous region, PR China) is governed by two competing transport agents: wind and water, which work in diametrically opposed directions. Net aeolian transport is from northeast to south, while fluvial transport occurs from the south to the north and then west to east at the northern rim, due to a gradual northward slope of the underlying topography. We here present the first comprehensive provenance study of Taklamakan desert sand with the aim to characterise the interplay of these two transport mechanisms and their roles in the formation of the sand sea, and to consider the potential of the Tarim Basin as a contributing source to the Chinese Loess Plateau (CLP). Our dataset comprises 39 aeolian and fluvial samples, which were characterised by detrital-zircon U-Pb geochronology, heavy-mineral, and bulk-petrography analyses. Although the inter-sample differences of all three datasets are subtle, a multivariate statistical analysis using multidimensional scaling (MDS) clearly shows that Tarim desert sand is most similar in composition to rivers draining the Kunlun Shan (south) and the Pamirs (west), and is distinctly different from sediment sources in the Tian Shan (north). A small set of samples from the Junggar Basin (north of the Tian Shan) yields different detrital compositions and age spectra than anywhere in the Tarim Basin, indicating that aeolian sediment exchange between the two basins is minimal. Although river transport dominates delivery of sand into the Tarim Basin, wind remobilises and reworks the sediment in the central sand sea. Characteristic signatures of main rivers can be traced from entrance into the basin to the terminus of the Tarim River, and those crossing the desert from the south to north can seasonally bypass sediment through the sand sea. Smaller ephemeral rivers from the Kunlun Shan end in the desert and discharge their sediment there. Both river run

  6. High temperature thermal energy storage in moving sand

    Science.gov (United States)

    Turner, R. H.; Awaya, H. I.

    1978-01-01

    Several high-temperature (to 500 C) heat-storage systems using sand as the storage medium are described. The advantages of sand as a storage medium include low cost for sand, widespread availability, non-toxicity, non-degradation characteristics, easy containment, and safety. The systems considered include: stationary sand with closely spaced tubes throughout the volume, the use of a fluidized bed, use of conveyor belt transporter, and the use of a blower rapid transport system. For a stationary sand bed, very close spacing of heat transfer tubes throughout the volume is required, manifesting as high power related system cost. The suggestion of moving sand past or around pipes is intended to reduce the power related costs at the penalty of added system complexity. Preliminary system cost estimates are offered. These rough calculations indicate that mobile sand heat storage systems cost less than the stationary sand approach.

  7. Characteristics of SCC with Fly Ash and Manufactured Sand

    Science.gov (United States)

    Praveen Kumar, K.; Radhakrishna

    2016-09-01

    Self compacting concrete (SCC) of M40 grade was designed. The binder in SCC consists of OPC and fly ash in the ratio of 65:35. River sand was replaced by manufactured sand (M-sand) at replacement levels of 20,40,60,80 and 100%. An attempt was made to evaluate the workability and strength characteristics of self compacting concrete with river sand and manufactured sand as fine aggregates. For each replacement level, constant workability was maintained by varying the dosage of superplasticizer. T50 flow time, V Funnel time, V-funnel T5 time as well as compressive, split tensile and flexural strength of SCC were found at each replacement level of M-sand. They were compared to SCC with river sand. Results indicate favourable use of M-sand in preparation of Self Compacting Concrete.

  8. A mountain of millipedes IV

    DEFF Research Database (Denmark)

    Enghoff, Henrik

    2016-01-01

    Two species of the genus Prionopetalum Attems, 1909, are recorded from the Udzungwa Mountains: P. asperginis sp. nov. and P. kraepelini (Attems, 1896). Prionopetalum stuhlmanni Attems, 1914, is synonymized under P. kraepelini. Odontopyge fasciata Attems, 1896, is transferred from Prionopetalum...

  9. The Table Mountain Field Site

    Data.gov (United States)

    Federal Laboratory Consortium — The Table Mountain Field Site, located north of Boulder, Colorado, is designated as an area where the magnitude of strong, external signals is restricted (by State...

  10. Geography and Weather: Mountain Meterology.

    Science.gov (United States)

    Mogil, H. Michael; Collins, H. Thomas

    1990-01-01

    Provided are 26 ideas to help children explore the effects of mountains on the weather. Weather conditions in Nepal and Colorado are considered separately. Nine additional sources of information are listed. (CW)

  11. Extinction of Harrington's mountain goat

    International Nuclear Information System (INIS)

    Mead, J.I.; Martin, P.S.; Euler, R.C.; Long, A.; Jull, A.J.T.; Toolin, L.J.; Donahue, D.J.; Linick, T.W.

    1986-01-01

    Keratinous horn sheaths of the extinct Harrington's mountain goat, Oreamnos harringtoni, were recovered at or near the surface of dry caves of the Grand Canyon, Arizona. Twenty-three separate specimens from two caves were dated nondestructively by the tandem accelerator mass spectrometer (TAMS). Both the TAMS and the conventional dates indicate that Harrington's mountain goat occupied the Grand Canyon for at least 19,000 years prior to becoming extinct by 11,160 +/- 125 radiocarbon years before present. The youngest average radiocarbon dates on Shasta ground sloths, Nothrotheriops shastensis, from the region are not significantly younger than those on extinct mountain goats. Rather than sequential extinction with Harrington's mountain goat disappearing from the Grand Canyon before the ground sloths, as one might predict in view of evidence of climatic warming at the time, the losses were concurrent. Both extinctions coincide with the regional arrival of Clovis hunters

  12. The Dilemma of Mountain Roads

    Science.gov (United States)

    Mountain roads and trails are proliferating throughout developing Southeast Asia with severe but largely unrecognized long-term consequences related to effects of landslides and surface erosion on communities and downstream resources.

  13. Field test on sand compaction pile method with copper slag sand; Dosuisai slag wo mochiita SCP koho no shiken seko

    Energy Technology Data Exchange (ETDEWEB)

    Minami, K.; Matsui, H.; Naruse, E.; Kitazume, M. [Port and Harbour Research Inst., Kanagawa (Japan)

    1997-09-20

    This paper describes the sand compaction pile (SCP) method using copper slag sand. The SCP method is a method by which sand compaction piles are constructed in the ground, and improvement can be obtained in a short period. This method has been widely used even in the port areas for enhancing the bearing power of soft clay ground and the lateral resistance of sheet pile. A great deal of sand is required as a material. The sand requires high permeability, proper size distribution with less fine particle fraction content, easy compaction property with enough strength, and easy discharging property from the casing of construction machines as required properties. Recently, it becomes hard to secure proper sand materials. The copper slag sand is obtained from refining process of copper as a by-product which is quenched in water flow and crushed in water. The copper slag sand has higher particle density than that of sand, excellent permeability, and similar size distribution to that of sand. From compaction drainage triaxial compression test and permeability test, it was found that the mechanical properties of copper slag sand did not change by the crushing of grains with keeping excellent permeability. Through the test construction, applicability of the copper slag sand to the SCP method could be confirmed as an alternate material of sand. 17 refs., 9 figs., 4 tabs.

  14. Yucca Mountain Project public interactions

    International Nuclear Information System (INIS)

    Reilly, B.E.

    1990-01-01

    The US Department of Energy (DOE) is committed to keeping the citizens of Nevada informed about activities that relate to the high-level nuclear waste repository program. This paper presents an overview of the Yucca Mountain Project's public interaction philosophy, objectives, activities and experiences during the two years since Congress directed the DOE to conduct site characterization activities only for the Yucca Mountain site

  15. Southeast Florida Sediment Assessment and Needs Determination (SAND) Study

    Science.gov (United States)

    2014-09-01

    sand with some shell beds, sandstone , and limestone *Miami Limestone 0 to 80 ft Oolitic limestone, quartz sand, and sandstone Anastasia 0 to 100 ft...Sand, shell beds, marl, calcareous sandstone (coquina/calcarenite) Fort Thompson 0 to 80 ft Silty limestone, silty sand, clayey marl, shell marl...highly- to moderately- weathered quartzose sandstone , and highly-weathered (saprolitic) to moderately-weathered hard limestone. North-south and

  16. Biodegradable materials as binders for IVth generation moulding sands

    OpenAIRE

    K. Major-Gabry

    2015-01-01

    This paper focuses on the possibility of using the biodegradable materials as binders (or parts of binders?compositions) for foundry moulding and core sands. Results showed that there is a great possibility of using available biodegradable materials as foundry moulding sand binders. Using biodegradable materials as partial content of new binders, or additives to moulding sands may not only decrease the toxicity and increase reclamation ability of tested moulding sands, but also accelerate the...

  17. SPECIFIC RESISTANCE AND SPECIFIC INTENSITY OF BELT SANDING OF WOOD

    Directory of Open Access Journals (Sweden)

    Boleslaw Porankiewicz

    2010-06-01

    Full Text Available This paper examines and discusses the specific belt sanding resistance K (N·cm-2 and specific belt sanding intensity SI (g·cm-2·min-1, for wood of Pinus sylvestris L., Picea abies L., Quercus robra L., Acer pseudoplatanus L., Alnus glutinosa Gaertn., and Populus Nigra L., by different sanding pressure pS, different sanding grit NG number, and different wood grain angles Phi(v.

  18. Quality stabilisation of synthetic sand containing bentonite in process lines

    OpenAIRE

    A. Fedoryszyn

    2010-01-01

    Stabilisation of sand quality requires the monitoring and control of sand moisture contents and its other parameters at each stage of sandprocessing, i.e. during the preparation of return sand mix and rebonding processes. Stabilisation of sand quality necessitates the use of reliable control equipment and evaluation procedures. This study outlines the scope and results of research work aimed to improve the control equipment to enhance the performance of turbine mixers. The paper reviews the m...

  19. Utilizing NASA Earth Observing System (EOS) Data to Determine Ideal Planting Locations for Wetland Tree Species in St. Bernard Parish, Louisiana

    Science.gov (United States)

    Reahard, Ross; Arguelles, Maria; Strong, Emma; Ewing, Michael; Kelly, Chelsey

    2012-01-01

    St. Bernard Parish, in southeast Louisiana, is rapidly losing coastal forests and wetlands due to a combination of natural and anthropogenic disturbances (e.g. subsidence, saltwater intrusion, low sedimentation, nutrient deficiency, herbivory, canal dredging, levee construction, spread of invasive species, etc.). After Hurricane Katrina severely impacted the area in 2005, multiple Non-Governmental Organizations (NGOs) have worked not only on rebuilding destroyed dwellings, but on rebuilding the ecosystems that once protected the citizens of St. Bernard Parish. Volunteer groups, NGOs, and government entities often work separately and independently of each other and use different sets of information to choose the best planting sites for coastal forests. Using NASA EOS, NRCS soil surveys, and ancillary road and canal data in conjunction with ground truthing, the team created maps of optimal planting sites for several species of wetland trees to aid in unifying these organizations, who share a common goal, under one plan. The methodology for this project created a comprehensive Geographic Information System (GIS) to help identify suitable planting sites in St. Bernard Parish. This included supplementing existing elevation data using LIDAR data and classifying existing land cover in the study area from ASTER multispectral satellite data. Low altitude AVIRIS hyperspectral imagery was used to assess the health of vegetation over an area near the intersection of the Mississippi River Gulf Outlet Canal (MRGO) and Bayou la Loutre. Historic extent of coastal forests was mapped using aerial photos from USGS collected between 1952 and 1956. The final products demonstrated the utility of combining NASA EOS with other geospatial data in assessing, monitoring, and restoring of coastal ecosystems in Louisiana. This methodology also provides a useful template for other ecological forecasting and coastal restoration applications.

  20. Evaluate of head loss, sediment value and copper removal in sand media (rapid sand filter

    Directory of Open Access Journals (Sweden)

    Daneshi Navab

    2014-06-01

    Full Text Available Along with the technology development and increasing consumption of water resources, we are experiencing low qualities in the mentioned resources. Copper brings about serious environment al pollution, threatening human health and ecosystem. This metal found variously in water resources and industrial activities. Therefore, it needs to treat the water resources from these excessive amounts. Different methods have used for this reason but the most used method during recent years has been the absorption by economic absorbers such as sand. Rapid sand filters usually used in water and wastewater treatment plants for water clarification. In this research, a single layer gravity rapid sand filter has used to reduce different concentrations of copper. sediment value and head loss arising in filter media is simulated by using combination of Carman-Kozeny, Rose and Gregory models in different discharges of rapid sand filter. Results have shown that with increasing in discharge and decreasing in input copper concentration, arriving time to given head loss, is increasing. In addition, results demonstrated that with increasing in copper concentration in influent, removal efficiency is decreasing somewhat. Results of this research can applied in an appropriate design of rapid sand filter to copper removal, a prediction of rapid sand filter ability to copper removal and an estimation of arising head loss during filter work thus evaluating of time interval backwash. DOI: http://dx.doi.org/10.3126/ije.v3i2.10641 International Journal of the Environment Vol.3(2 2014: 276-286

  1. Dewatering Behaviour of Fine Oil Sands Tailings : An Experimental Study

    NARCIS (Netherlands)

    Yao, Y.

    2016-01-01

    Oil sands tailings are a warm aqueous suspension of sand, silt, clay, residual bitumen and naphtha. The tailings are hydraulically transported and stored in tailing ponds where they segregate, with the sand settling from suspension forming beaches and the remaining tailings flowing to the middle of

  2. Design and Fabrication of a Foundry Sand Mixer Using Locally ...

    African Journals Online (AJOL)

    Most small foundry shops mix their sand manually which is not efficient since homogenous mix cannot be guaranteed and even when foundry mixer are available most of them are imported costing the nation huge foriegn exchange. A foundry sand mixer capable of mixing foundry sand has been designed and fabricated ...

  3. Seasonal changing sand waves and the effect of surface waves

    NARCIS (Netherlands)

    Sterlini, Fenneke; van Dijk, Thaiënne A.G.P.; IJzer, Steven; Hulscher, Suzanne; Schüttrumpf, Holger; Tomasicchio, Guiseppe Roberto

    2012-01-01

    Sand waves are wavelike subaqueous sediment structures that exist in large areas in shelf seas. Due to their characteristics sand waves can severely affect human offshore activities, such as navigation. This makes it important to understand the physical processes that shape and change sand waves. In

  4. Short Communications Sand moisture as a factor determining depth ...

    African Journals Online (AJOL)

    1993-11-05

    Nov 5, 1993 ... The depths to which the animals burrow are, at least partly. determined by the moisture gradient in the sand. They are, however, incapable of burrowing into totally dry sand. Animals alter their position in the sand in response to changes in moisture content so as to ensure exposure to suitable conditions.

  5. Assessing environmental impacts of inland sand mining in parts of ...

    African Journals Online (AJOL)

    Sand is a valuable resource for construction and other purposes, however sand mining often result in serious environmental problems such as land degradation, loss of agricultural lands and biodiversity, as well increased poverty among people. This study assessed the environmental impacts of inland sand mining in six ...

  6. Acetylcholinesterase mutations and organophosphate resistance in sand flies and mosquitoes

    Science.gov (United States)

    Leishmaniasis is an insect-borne disease caused by several protozoan species in the genus Leishmania, which are vectored by sand fly species in the genera Phlebotomus or Lutzomyia, depending on the sand fly species geographic range. Sand fly bites and leishmaniasis significantly impacted U.S. milita...

  7. Ecological restoration and recovery in the wind-blown sand hazard areas of northern China: relationship between soil water and carrying capacity for vegetation in the Tengger Desert.

    Science.gov (United States)

    Li, XingRong; Zhang, ZhiShan; Tan, HuiJuan; Gao, YanHong; Liu, LiChao; Wang, XingPing

    2014-05-01

    The main prevention and control area for wind-blown sand hazards in northern China is about 320000 km(2) in size and includes sandlands to the east of the Helan Mountain and sandy deserts and desert-steppe transitional regions to the west of the Helan Mountain. Vegetation recovery and restoration is an important and effective approach for constraining wind-blown sand hazards in these areas. After more than 50 years of long-term ecological studies in the Shapotou region of the Tengger Desert, we found that revegetation changed the hydrological processes of the original sand dune system through the utilization and space-time redistribution of soil water. The spatiotemporal dynamics of soil water was significantly related to the dynamics of the replanted vegetation for a given regional precipitation condition. The long-term changes in hydrological processes in desert areas also drive replanted vegetation succession. The soil water carrying capacity of vegetation and the model for sand fixation by revegetation in aeolian desert areas where precipitation levels are less than 200 mm are also discussed.

  8. Sand Needs and Resources Offshore New York

    Science.gov (United States)

    Lashley, J. M.; Flood, R. D.; White, M.; Bokuniewicz, H.; Hinrichs, C.; Wilson, R. E.

    2016-02-01

    "Superstorm" Sandy (October, 2012) accentuated the persistent problem of coastal erosion on New York's ocean coast. The New York state Department of State in cooperation with the Bureau of Ocean Energy Management has initiated further identification and assessment of marine sand reserves required to improve the resiliency of coastal communities and the maintenance of coastal habitats. The historical demand for beach nourishment has been about 1.5 million cubic meters per year, but sea level rise and the occurrence of extreme conditions may increase the demand to over 5 million cubic meters annually. Forty-four historical and proposed borrow sites have been delineated. This inner shelf is both sand rich and data rich. Geophysical and geological data has been compiled and reassessed to support identification, characterization, and delineation of sand resources for potential use in future coastal restoration, beach nourishment, and/or wetland restoration efforts. The South Shore of Long Island is composed in part by the Fire Island National Seashore. Holocene sand ridges extending at an oblique angle to the cross shore in the seaward direction. Borrow pits among the sand ridges, excavated were apparent in the most recent surveys and it appears that natural replenishment of offshore borrow areas has been occurring although the rates need to be determined in order to assess their sustainability. Not only is the area one of intense societal attention, but the use of this resource for coastal resilience must fit into a diverse framework marine spatial planning including not only traditional components, like commercial fishing, but also new factors like the siting of offshore wind-farms. To extend this assessment will include a recent survey, sponsored by the Bureau of Ocean Energy Management and the New York Department of State, providing approximately 700 km of geophysical survey lines located between 3 and 9 nautical miles offshore, and 46 geotechnical samples

  9. The Rheology of Acoustically Fluidized Sand

    Science.gov (United States)

    Conrad, J. W.; Melosh, J.

    2013-12-01

    The collapse of large craters and the formation of central peaks and peak rings is well modeled by numerical computer codes that incorporate the acoustic fluidization mechanism to temporarily allow the fluid-like flow of rock debris immediately after crater excavation. Furthermore, long runout landslides require a similar mechanism to explain their almost frictionless movement, which is probably also a consequence of their granular composition coupled with internal vibrations. Many different investigators have now confirmed the ability of vibrations to fluidize granular materials. Yet it still remains to fully describe the rheology of vibrated sand as a function of stress, frequency and amplitude of the vibrations in the sand itself. We constructed a rotational viscometer to quantitatively investigate the relation between the stress and strain rate in a horizontal bed of strongly vibrated sand. In addition to the macroscopic stain rate, the amplitude and frequency of the vibrations produced by a pair of pneumatic vibrators were also measured with the aid of miniaturized piezoelectric accelerometers (B&K 4393) whose output was recorded on a digital storage oscilloscope. The initial gathering of the experimental data was difficult due to granular memory, but by having the sand compacted vibrationally for 8 minutes before each run the scatter of data was reduced and we were able to obtain consistent results. Nevertheless, our major source of uncertainty was variations in strain rate from run to run. We find that vibrated sand flows like a highly non-Newtonian fluid, in which the shear strain rate is proportional to stress to a power much greater than one, where the precise power depends on the amplitude and frequency of the applied vibrations. Rapid flow occurs at stresses less than half of the static yield stress (that is, the yield stress when no vibration is applied) when strong vibrations are present. For a Newtonian fluid, such as water, the relation between

  10. The origins of mountain geoecology

    Directory of Open Access Journals (Sweden)

    Ives, Jack D.

    2012-05-01

    Full Text Available Mountain geoecology, as a sub-discipline of Geography, stems from the life and work of Carl Troll who, in turn, was inspired by the philosophy and mountain travels of Alexander von Humboldt. As founding chair of the IGU Commission on High-Altitude Geoecology (1968, Troll laid the foundations for inter-disciplinary and international mountain research. The paper traces the evolution of the Commission and its close links with the UNESCO Man and Biosphere Programme (1972- and the United Nations University’s mountain Project (1978-. This facilitated the formation of a major force for inclusion of a mountain chapter in AGENDA 21 during the 1992 Rio de Janeiro Herat Summit (UNCED and the related designation by the United Nations of 2002 as the International Year of Mountains. In this way, mountain geoecology not only contributed to worldwide mountain research but also entered the political arena in the struggle for sustainable mountain development and the well-being of mountain people.La geoecología de montaña, como sub-disciplina de la Geografía, entronca con la vida y trabajo de Carl Troll, quien, a su vez, fue inspirado por la filosofía y viajes de Alexander von Humboldt. Como presidente fundador de la comisión de la UGI sobre High Altitude Geoecology (1968, Troll colocó las bases para la investigación interdisciplinar e internacional de las montañas. Este trabajo presenta la evolución de la Comisión y sus estrechas relaciones con el Programa Hombre y Biosfera de UNESCO (1972- y con el Proyecto de montaña de la Universidad de Naciones Unidas (1978-. Esto facilitó la inclusión de un capítulo sobre la montaña en AGENDA 21 durante la Cumbre de la Tierra de Río de Janeiro (UNCED, y la consiguiente designación de 2002 como el Año Internacional de las Montañas por parte de Naciones Unidas. En este sentido, la geoecología de montaña no sólo contribuyó a la investigación de las montañas del mundo sino que también empujó a la pol

  11. A preliminary comparison of mineral deposits in faults near Yucca Mountain, Nevada, with possible analogs

    International Nuclear Information System (INIS)

    Vaniman, D.T.; Bish, D.L.; Chipera, S.

    1988-05-01

    Several faults near Yucca Mountain, Nevada, contain abundant calcite and opal-CT, with lesser amounts of opal-A and sepiolite or smectite. These secondary minerals are being studied to determine the directions, amounts, and timing of transport involved in their formation. Such information is important for evaluating the future performances of a potential high-level nuclear waste repository beneath Yucca Mountain. This report is a preliminary assessment of how those minerals were formed. Possible analog deposits from known hydrothermal veins, warm springs, cold springs or seeps, soils, and aeolian sands were studied by petrographic and x-ray diffraction methods for comparison with the minerals deposited in the faults; there are major mineralogic differences in all of these environments except in the aeolian sands and in some cold seeps. Preliminary conclusions are that the deposits in the faults and in the sand ramps are closely related, and that the process of deposition did not require upward transport from depth. 35 refs., 25 figs

  12. The physics of wind-blown sand and dust.

    Science.gov (United States)

    Kok, Jasper F; Parteli, Eric J R; Michaels, Timothy I; Karam, Diana Bou

    2012-10-01

    The transport of sand and dust by wind is a potent erosional force, creates sand dunes and ripples, and loads the atmosphere with suspended dust aerosols. This paper presents an extensive review of the physics of wind-blown sand and dust on Earth and Mars. Specifically, we review the physics of aeolian saltation, the formation and development of sand dunes and ripples, the physics of dust aerosol emission, the weather phenomena that trigger dust storms, and the lifting of dust by dust devils and other small-scale vortices. We also discuss the physics of wind-blown sand and dune formation on Venus and Titan.

  13. Longshore sediment transport at Golden Sands (Bulgaria

    Directory of Open Access Journals (Sweden)

    Hristo Nikolov

    2006-09-01

    Full Text Available The paper presents the results of studies on the qualitative and quantitative features of the littoral drift at Golden Sands (Bulgaria, carried out jointly by Polish and Bulgarian researchers. The mathematical modelling of physical coastal processes took wave transformation (wave diffraction and refraction; the effects of shoaling and wave breaking and longshore sediment transport into account. The computations were carried out for the mean statistical annual wave climate, determined on the basis of IO BAS wave data, simulated using the WAM method from long-term Black Sea wind data. The results of sediment transport computations clearly show that its direction off the Golden Sands shore is from north to south.

  14. Oil sands tailings preliminary ecological risk assessment

    International Nuclear Information System (INIS)

    1994-01-01

    Chemical data collected from various oil sands soil-tailings mixtures were used to determine the ecological risk that such tailings would pose to terrestrial wildlife at the surface of a reclaimed site. A methodology that could be used to evaluate the risks posed by various reclamation options (for dry land only) was proposed. Risks associated with other reclamation options, such as wet landscapes or deeper in-pit disposal, were not evaluated. Ten constituents (eight organic and two inorganic) were found to pose a threat to terrestrial biota. The relative contribution of different exposure pathways (water and food ingestion, incidental soil ingestion, inhalation) were studied by probabilistic models. Some physical and chemical reclamation alternatives which involve incorporating oil sands tailings in the landscape to produce a surface that could sustain a productive ecosystem, were described. 53 refs., 15 tabs., 3 figs

  15. Tailings dewatering in the oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Longo, S.; Labelle, M. [Golder Paste Technology, Sudbury, ON (Canada); Wislesky, I. [Golder Associates Ltd., Calgary, AB (Canada)

    2010-07-01

    Alberta's Directive 074 was established to reduce fluid tailings produced during oil sands extraction processes. This PowerPoint presentation examined some of the dewatering strategies available for oil sands operators and provided recommendations for implementing a dewatering plan. Sites must be evaluated in order to determine their chemistry, mineralogy, and the total quantity of material to be handled. The availability of potential additives must also be considered. Process technologies must be selected in relation to the operator's depositional strategy. Each site will require its own unique dewatering and depositional strategy. Dewatering technologies include thickening; in-line flocculation; centrifuge; co-mingling; and various new technologies such as electro-osmosis. Laboratory testing programs include index tests, primary stream thickening, and mini-pilot plant testing. The performance of various testing formats was evaluated. Thickening and depositional techniques were reviewed. tabs., figs.

  16. Radiation protection in the sand pit

    International Nuclear Information System (INIS)

    Hewson, Greg

    1997-01-01

    Radiation protection in the Western Australian minerals sands industry has attracted considerable controversy over the last 20 years: firstly, in relation to environmental and public health issues associated with the indiscriminate disposal of radioactive tailings as landfill in the mid to late 1970s and, secondly, in relation to occupational health issues associated with excessive radiation exposures to some workers at some plants in the mid to late 1980s. The industry also attracts attention through its proximity to coastal regions and population centres and consequent land use conflicts. Owing to intense political and societal scrutiny, and the emotional responses evoked by radiation, the industry's survival depends on a continuing high level of environmental and safety performance. This article summarises the successes and failures of the mineral sands industry in managing radiation protection and highlights some future issues and challenges for the industry. (Author)

  17. Oil sands market and transportation solutions

    International Nuclear Information System (INIS)

    Sandahl, R.

    2004-01-01

    This presentation outlined the immense potential of the western Canadian oil sands reserves. Recoverable reserves have been estimated at 180 billion barrels, with production forecasts estimated at 5 million barrels per day by 2030. Resource development is occurring at a time when the world's largest oil importer is increasing supplies through concern for security of supply. The second and third largest oil importers in the world are experiencing economic and energy demand growth. These factors underscore the motivation for rapid growth of the Western Canadian Oil Sands reserves. One of the challenges that must be addressed is to ensure that incremental markets for the increased production are accessed. Another challenge is to ensure adequate infrastructure in terms of pipeline capacity to ensure deliverability of the product. tabs., figs

  18. Pullout capacity of batter pile in sand.

    Science.gov (United States)

    Nazir, Ashraf; Nasr, Ahmed

    2013-03-01

    Many offshore structures are subjected to overturning moments due to wind load, wave pressure, and ship impacts. Also most of retaining walls are subjected to horizontal forces and bending moments, these forces are due to earth pressure. For foundations in such structures, usually a combination of vertical and batter piles is used. Little information is available in the literature about estimating the capacity of piles under uplift. In cases where these supporting piles are not vertical, the behavior under axial pullout is not well established. In order to delineate the significant variables affecting the ultimate uplift shaft resistance of batter pile in dry sand, a testing program comprising 62 pullout tests was conducted. The tests are conducted on model steel pile installed in loose, medium, and dense sand to an embedded depth ratio, L/d, vary from 7.5 to 30 and with various batter angles of 0°, 10°, 20°, and 30°. Results indicate that the pullout capacity of a batter pile constructed in dense and/or medium density sand increases with the increase of batter angle attains maximum value and then decreases, the maximum value of Pα occurs at batter angle approximately equal to 20°, and it is about 21-31% more than the vertical pile capacity, while the pullout capacity for batter pile that constructed in loose sand decreases with the increase of pile inclination. The results also indicated that the circular pile is more resistant to pullout forces than the square and rectangular pile shape. The rough model piles tested is experienced 18-75% increase in capacity compared with the smooth model piles. The suggested relations for the pullout capacity of batter pile regarding the vertical pile capacity are well predicted.

  19. Solvent extraction of Southern US tar sands

    Energy Technology Data Exchange (ETDEWEB)

    Penney, W.R.

    1990-01-01

    The Department of Chemical Engineering at the University of Arkansas, in association with Diversified Petroleum Recovery, Inc. (DPR) of Little Rock, Arkansas, has been developing a solvent extraction process for the recovery of bitumen from tar sands for the past five years. The unique feature of the process is that the bitumen is recovered from the solvent by contacting with a co-solvent, which causes the bitumen to precipitate. The overall purpose of this project is to study both the technical and economic feasibility of applying this technology for recovery of bitumen from tar sands by (1) investigating the socioeconmic factors which affect (a) plant siting and (b) the market value of recovered bitumen; (2) operating a process demonstration unit at the rate of 1 lb/hr recovered bitumen while producing clean sand and recyclable solvents; and (3) determine the economic conditions which will make a bitumen recovery project economical. DPR has analyzed the historical trends of domestic production, consumption, discoveries and reserves of crude oil. They have started an investigation of the volatility in the price of crude oil and of gasoline prices and of the differential between gasoline and crude oil. DPR continues to analyze the geographical movement and demand for asphalt products. Utah does not appear economically attractive as a site for a bitumen from tar sands asphalt plant. Oklahoma sites are now being studied. This report also contains the quarterly progress report from a University of Nevada study to determine bitumen composition, oxygen uptake rates, and viscosities of Alabama and Utah bitumens. Both reports have been indexed separately for inclusion on the data base.

  20. Comparison of SAND-II and FERRET

    International Nuclear Information System (INIS)

    Wootan, D.W.; Schmittroth, F.

    1981-01-01

    A comparison was made of the advantages and disadvantages of two codes, SAND-II and FERRET, for determining the neutron flux spectrum and uncertainty from experimental dosimeter measurements as anticipated in the FFTF Reactor Characterization Program. This comparison involved an examination of the methodology and the operational performance of each code. The merits of each code were identified with respect to theoretical basis, directness of method, solution uniqueness, subjective influences, and sensitivity to various input parameters

  1. Drained Triaxial Tests on Eastern Scheldt Sand

    DEFF Research Database (Denmark)

    Praastrup, U.; Jakobsen, Kim Parsberg

    In the process of understanding and developing models for geomaterials, the stress-strain behaviour is commonly studied by performing triaxial tests. In the present study static triaxial tests have been performed to gain knowledge of the stress-strain behaviour of frictional materials during...... monotonic loading. The tests reported herein are all drained tests, starting from different initial states of stress and following various stress paths. AIl the tests are performed on reconstituted medium dense specimens of Eastern Scheldt Sand....

  2. Pullout capacity of batter pile in sand

    Directory of Open Access Journals (Sweden)

    Ashraf Nazir

    2013-03-01

    Full Text Available Many offshore structures are subjected to overturning moments due to wind load, wave pressure, and ship impacts. Also most of retaining walls are subjected to horizontal forces and bending moments, these forces are due to earth pressure. For foundations in such structures, usually a combination of vertical and batter piles is used. Little information is available in the literature about estimating the capacity of piles under uplift. In cases where these supporting piles are not vertical, the behavior under axial pullout is not well established. In order to delineate the significant variables affecting the ultimate uplift shaft resistance of batter pile in dry sand, a testing program comprising 62 pullout tests was conducted. The tests are conducted on model steel pile installed in loose, medium, and dense sand to an embedded depth ratio, L/d, vary from 7.5 to 30 and with various batter angles of 0°, 10°, 20°, and 30°. Results indicate that the pullout capacity of a batter pile constructed in dense and/or medium density sand increases with the increase of batter angle attains maximum value and then decreases, the maximum value of Pα occurs at batter angle approximately equal to 20°, and it is about 21–31% more than the vertical pile capacity, while the pullout capacity for batter pile that constructed in loose sand decreases with the increase of pile inclination. The results also indicated that the circular pile is more resistant to pullout forces than the square and rectangular pile shape. The rough model piles tested is experienced 18–75% increase in capacity compared with the smooth model piles. The suggested relations for the pullout capacity of batter pile regarding the vertical pile capacity are well predicted.

  3. Transport processes in intertidal sand flats

    Science.gov (United States)

    Wu, Christy

    2010-05-01

    Methane rich sulfate depleted seeps are observed along the low water line of the intertidal sand flat Janssand in the Wadden Sea. It is unclear where in the flat the methane is formed, and how it is transported to the edge of the sand flat where the sulfidic water seeps out. Methane and sulfate distributions in pore water were determined along transects from low water line toward the central area of the sand flat. The resulting profiles showed a zone of methane-rich and sulfate-depleted pore water below 2 m sediment depth. Methane production and sulfate reduction are monitored over time for surface sediments collected from the upper flat and seeping area. Both activities were at 22 C twice as high as at 15 C. The rates in sediments from the central area were higher than in sediments from the methane seeps. Methanogenesis occurred in the presence of sulfate, and was not significantly accelerated when sulfate was depleted. The observations show a rapid anaerobic degradation of organic matter in the Janssand. The methane rich pore water is obviously transported with a unidirectional flow from the central area of the intertidal sand flat toward the low water line. This pore water flow is driven by the pressure head caused by elevation of the pore water relative to the sea surface at low tide (Billerbeck et al. 2006a). The high methane concentration at the low water line accumulates due to a continuous outflow of pore water at the seepage site that prevents penetration of electron acceptors such as oxygen and sulfate to reoxidize the reduced products of anaerobic degradation (de Beer et al. 2006). It is, however, not clear why no methane accumulates or sulfate is depleted in the upper 2 m of the flats.

  4. Guide to preparing SAND reports. Revised

    Energy Technology Data Exchange (ETDEWEB)

    Locke, T.K. [ed.

    1996-04-01

    This guide contains basic information needed to produce a SAND report. Its guidelines reflect DOE regulation and Sandia policy. The guide includes basic writing instructions in an annotated sample report; guidance for organization, format, and layout of reports produced by line organizations; and information about conference papers, journal articles, and brochures. The appendixes contain sections on Sandia`s preferred usage, equations, references, copyrights and permissions, and publishing terms.

  5. Analysis of wind-blown sand movement over transverse dunes.

    Science.gov (United States)

    Jiang, Hong; Huang, Ning; Zhu, Yuanjian

    2014-12-01

    Wind-blown sand movement often occurs in a very complicated desert environment where sand dunes and ripples are the basic forms. However, most current studies on the theoretic and numerical models of wind-blown sand movement only consider ideal conditions such as steady wind velocity, flat sand surface, etc. In fact, the windward slope gradient plays a great role in the lift-off and sand particle saltation. In this paper, we propose a numerical model for the coupling effect between wind flow and saltating sand particles to simulate wind-blown sand movement over the slope surface and use the SIMPLE algorithm to calculate wind flow and simulate sands transport by tracking sand particle trajectories. We furthermore compare the result of numerical simulation with wind tunnel experiments. These results prove that sand particles have obvious effect on wind flow, especially that over the leeward slope. This study is a preliminary study on windblown sand movement in a complex terrain, and is of significance in the control of dust storms and land desertification.

  6. Naphtha evaporation from oil sands tailings ponds

    Energy Technology Data Exchange (ETDEWEB)

    Kasperski, K.; Munoz, V.; Mikula, R. [Natural Resources Canada, Devon, AB (Canada). CANMET Western Research Centre

    2010-07-01

    The environmental impacts of volatile organic compounds (VOCs) from oil sands tailings ponds must be considered when evaluating new oil sands mining and extraction operations. Studies have suggested that only 40 percent of the solvent sent to tailings ponds is available to the environment, while the rest is irreversibly trapped. The recovery of hydrocarbons from oil sands froth process water is low. This PowerPoint presentation discussed a method of distinguishing between water and hydrocarbons at low temperatures. Samples were heated to 246 degrees C at 15 degrees C and held for 10 minutes. Heating was then resumed at 750 degrees C and held for 10 minutes in a pyrolysis phase, then cooled and reheated with an oxygen addition. The method demonstrated that the diluent distribution between the solids and water phases is misinterpreted as diluent that will evaporate, and diluent that will not evaporate. The study concluded by suggesting that the definition of recoverable and unrecoverable hydrocarbon should be re-termed as easily recoverable, and difficult to recover. tabs., figs.

  7. Insight conference reports : Western Canada oil sands

    International Nuclear Information System (INIS)

    2005-01-01

    This conference presented issues of concern to the Canadian oil sands industry. Focal points included supply and the potential for market growth as well as opportunities and challenges faced by the industry in the current market. Various projects were discussed, including the Northern Lights and Fort Hill projects. Reserves and resource booking procedures were examined, as well as issues concerning the streamlining of regulatory barriers and various approaches to the Kyoto Protocol and greenhouse gas (GHG) emissions. Oil sands portfolios were reviewed as well as issues concerning the recovery of titanium and zircon, the economics of Steam Assisted Gravity Drainage (SAGD) options and innovations in technology and sub-surface risk assessment for in-situ projects. Transportation initiatives were examined as well as pipeline issues and storage infrastructure development. Issues concerning financing as well as the economic environment of the oil sands industry were also discussed. The conference featured 20 presentations, of which 5 have been catalogued separately for inclusion in this database. tabs, figs

  8. Recycled sand in lime-based mortars.

    Science.gov (United States)

    Stefanidou, M; Anastasiou, E; Georgiadis Filikas, K

    2014-12-01

    The increasing awareness of the society about safe guarding heritage buildings and at the same time protecting the environment promotes strategies of combining principles of restoration with environmentally friendly materials and techniques. Along these lines, an experimental program was carried out in order to investigate the possibility of producing repair, lime-based mortars used in historic buildings incorporating secondary materials. The alternative material tested was recycled fine aggregates originating from mixed construction and demolition waste. Extensive tests on the raw materials have been performed and mortar mixtures were produced using different binding systems with natural, standard and recycled sand in order to compare their mechanical, physical and microstructure properties. The study reveals the improved behavior of lime mortars, even at early ages, due to the reaction of lime with the Al and Si constituents of the fine recycled sand. The role of the recycled sand was more beneficial in lime mortars rather than the lime-pozzolan or lime-pozzolan-cement mortars as a decrease in their performance was recorded in the latter cases due to the mortars' structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. Numerical simulation of sand jet in water

    Energy Technology Data Exchange (ETDEWEB)

    Azimi, A.H.; Zhu, D.; Rajaratnam, N. [Alberta Univ., Edmonton, AB (Canada). Dept. of Civil and Environmental Engineering

    2008-07-01

    A numerical simulation of sand jet in water was presented. The study involved a two-phase flow using two-phase turbulent jets. A literature review was also presented, including an experiment on particle laden air jet using laser doppler velocimetry (LDV); experiments on the effect of particle size and concentration on solid-gas jets; an experimental study of solid-liquid jets using particle image velocimetry (PIV) technique where mean velocity and fluctuations were measured; and an experimental study on solid-liquid jets using the laser doppler anemometry (LDA) technique measuring both water axial and radial velocities. Other literature review results included a photographic study of sand jets in water; a comparison of many two-phase turbulent flow; and direct numerical simulation and large-eddy simulation to study the effect of particle in gas jet flow. The mathematical model and experimental setup were also included in the presentation along with simulation results for sand jets, concentration, and kinetic energy. The presentation concluded with some proposed future studies including numerical simulation of slurry jets in water and numerical simulation of slurry jets in MFT. tabs., figs.

  10. Mobil Oil Canada : Kearl Oil Sands Mine

    International Nuclear Information System (INIS)

    1997-01-01

    The upgrader design at Mobil's Kearl Oil Sands Mine were described. Included were feed characteristics, upgrader products, process schemes and their overall economics and upgrader technologies in use, including coking, deasphalting, hydrocracking, hydrotreating and visbreaking. Advantages and disadvantages of the upgrader technologies were highlighted. As far as the product is concerned, much of it is destined to U.S. refineries that are equipped to process the material. The Kearl Oil Sands Mine upgrading facility will likely use a combination of coker/hydrotreating, which is a well proven process for high value products that has been used in all five of Mobil's refineries in the U.S., and visbreaker/deasphalting, which has shown promise in bench-scale testing, but at present still has some potential commercial difficulties. Foremost among these are the high softening product of asphalt from visbroken products, questionable commercial feasibility of the low yield of pitch, and problems in the disposal of asphalt. Severe visbreaking also yields unstable products. Details of Mobil Canada's oil sands project were also summarized 2 tabs., 9 figs

  11. Experimental investigation of sanding propensity for the Andrew completion

    Energy Technology Data Exchange (ETDEWEB)

    Venkitaraman, A.; Li, H. [Schlumberger Perforating and Testing Center (United Kingdom); Leonard, A. J.; Bowden, P. R. [BP Exploration (United Kingdom)

    1998-12-31

    A series of laboratory experiments were performed on three reservoir core samples selected from two plot wells to confirm the likelihood of sand production during the completion phase of the planned Andrew horizontal wells, and to perform risk analysis of formation failure at the time of underbalance perforation, and expected producing conditions. CT scans revealed no perforation failure, and the core samples did not show any propensity to produce sand during single-phase oil flow. Transient sand production was observed when water cut was introduced, but sand production declined as the percentage of water cut was increased. There was no evidence of sand production in the core samples during depletion testing either, and the wells were subsequently completed with perforated cemented liners without sand control. No sand problems have been encountered in two years of production, with some wells in water cut and declined reservoir pressure of 200 psi. 8 refs., 3 tabs., 5 figs.

  12. Use of sand wave habitats by silver hake

    Science.gov (United States)

    Auster, P.J.; Lindholm, J.; Schaub, S.; Funnell, G.; Kaufman, L.S.; Valentine, P.C.

    2003-01-01

    Silver hake Merluccius bilinearis are common members of fish communities in sand wave habitats on Georges Bank and on Stellwagen Bank in the Gulf of Maine. Observations of fish size v. sand wave period showed that silver hake are not randomly distributed within sand wave landscapes. Regression analyses showed a significant positive relationship between sand wave period and fish length. Correlation coefficients, however, were low, suggesting other interactions with sand wave morphology, the range of current velocities, and available prey may also influence their distribution. Direct contact with sand wave habitats varied over diel periods, with more fish resting on the seafloor during daytime than at night. Social foraging, in the form of polarized groups of fish swimming in linear formations during crepuscular and daytime periods, was also observed. Sand wave habitats may provide shelter from current flows and mediate fish-prey interactions. ?? 2003 The Fisheries Society of the British Isles.

  13. bentonite-sand mixture as new backfill/buffer material

    International Nuclear Information System (INIS)

    Cui Suli; Liu Jisheng; Zhang Huyuan; Liang Jian

    2008-01-01

    The mixture of bentonite and quartz sand is suggested as a new backfill/buffer material for geological disposal of HLW. To improve the further design of underground laboratory and in-situ industrial construction test, the optimization of sand addition to bentonite is focused at present research stage. Based on summarizing the research results abroad, laboratory tests were conducted on the mixture of GMZ001 bentonite and quartz sand, such as compaction test and swelling tests etc. Test data shows that GMZ bentonite-sand mixture exhibits a favorite compaction with a 30% sand addition, a highest swelling pressure with a 20% sand addition, and a decreasing plasticity with increases in sand addition and pore liquid concentration. (authors)

  14. Parish school inspection as a means of implementation of the policy on Paraná’s provincial education (1853-1889

    Directory of Open Access Journals (Sweden)

    Maria Elisabeth Blanck Miguel

    2015-07-01

    Full Text Available This paper addresses the primary public inspection, particularly that exercised by parish inspectors, considered as one of the forms of manifestation of the policy on education. A research about reports and official letters concerning the primary public education in Paraná in the provincial period (1853-1889 shows ordinary school issues and, especially, the relationship between teachers and the authorities responsible for the administration and control of the work in schools. This paper aims to deep the knowledge on parish inspection and literary council, as components of the inspection that used to be present in the relations between teachers and inspectors. The methodology includes documental research, analysis of sources and crossing of information from reports and official letters with the provincial legislation of Paraná. We can conclude that, in spite of a relative legal organization when it comes to the distribution of administrative functions and control over public instruction, the latter remained quite precarious at the end of the provincial period, since only with the advance of social relations of production of material life the school would become necessary.

  15. Sand wave fields beneath the Loop Current, Gulf of Mexico: Reworking of fan sands

    Science.gov (United States)

    Kenyon, Neil H.; Akhmetzhanov, A.M.; Twichell, D.C.

    2002-01-01

    Extensive fields of large barchan-like sand waves and longitudinal sand ribbons have been mapped by deep-towed SeaMARC IA sidescan sonar on part of the middle and lower Mississippi Fan that lies in about 3200 m of water. The area is beneath the strongly flowing Loop Current. The bedforms have not been adequately sampled but probably consist of winnowed siliciclastic-foraminiferal sands. The size (about 200 m from wingtip to wingtip) and shape of the large barchans is consistent with a previously observed peak current speed of 30 cm/s, measured 25 m above the seabed. The types of small-scale bedforms and the scoured surfaces of chemical crusts, seen on nearby bottom photographs, indicate that near-bed currents in excess of 30 cm/s may sometimes occur. At the time of the survey the sand transport direction was to the northwest, in the opposite direction to the Loop Current but consistent with there being a deep boundary current along the foot of the Florida Escarpment. Some reworking of the underlying sandy turbidites and debris flow deposits is apparent on the sidescan sonar records. Reworking by deep-sea currents, resulting in erosion and in deposits characterised by coarsening upwards structures and cross-bedding, is a process that has been proposed for sand found in cores in shallower parts of the Gulf of Mexico. This process is more widespread than hitherto supposed. 

  16. Rhodamine-WT dye losses in a mountain stream environment

    Science.gov (United States)

    Bencala, Kenneth E.; Rathburn, Ronald E.; Jackman, Alan P.; Kennedy, Vance C.; Zellweger, Gary W.; Avanzino, Ronald J.

    1983-01-01

    A significant fraction of rhodamine WT dye was lost during a short term multitracer injection experiment in a mountain stream environment. The conservative anion chloride and the sorbing cation lithium were concurrently injected. In-stream rhodamine WT concentrations were as low as 45 percent of that expected, based on chloride data. Concentration data were available from shallow‘wells’dug near the stream course and from a seep of suspected return flow. Both rhodamine WT dye and lithium were nonconservative with respect to the conservative chloride, with rhodamine WT dye closely following the behavior of the sorbing lithium.Nonsorption and sorption mechanisms for rhodamine WT loss in a mountain stream were evaluated in laboratory experiments. Experiments evaluating nonsorption losses indicated minimal losses by such mechanisms. Laboratory experiments using sand and gravel size streambed sediments show an appreciable capacity for rhodamine WT sorption.The detection of tracers in the shallow wells and seep indicates interaction between the stream and the flow in the surrounding subsurface, intergravel water, system. The injected tracers had ample opportunity for intimate contact with materials shown in the laboratory experiments to be potentially sorptive. It is suggested that in the study stream system, interaction with streambed gravel was a significant mechanism for the attenuation of rhodamine WT dye (relative to chloride).

  17. Substantial soil organic carbon retention along floodplains of mountain streams

    Science.gov (United States)

    Sutfin, Nicholas A.; Wohl, Ellen

    2017-07-01

    Small, snowmelt-dominated mountain streams have the potential to store substantial organic carbon in floodplain sediment because of high inputs of particulate organic matter, relatively lower temperatures compared with lowland regions, and potential for increased moisture conditions. This work (i) quantifies mean soil organic carbon (OC) content along 24 study reaches in the Colorado Rocky Mountains using 660 soil samples, (ii) identifies potential controls of OC content based on soil properties and spatial position with respect to the channel, and (iii) and examines soil properties and OC across various floodplain geomorphic features in the study area. Stepwise multiple linear regression (adjusted r2 = 0.48, p sample depth, percent sand, distance from the channel, and relative elevation from the channel are significant predictors of OC content in the study area. Principle component analysis indicates limited separation between geomorphic floodplain features based on predictors of OC content. A lack of significant differences among floodplain features suggests that the systematic random sampling employed in this study can capture the variability of OC across floodplains in the study area. Mean floodplain OC (6.3 ± 0.3%) is more variable but on average greater than values in uplands (1.5 ± 0.08% to 2.2 ± 0.14%) of the Colorado Front Range and higher than published values from floodplains in other regions, particularly those of larger rivers.

  18. Mountain biking injuries: a review.

    Science.gov (United States)

    Carmont, Michael R

    2008-01-01

    Mountain biking is a fast, exciting adventure sport with increasing numbers of participants and competitions. A search of PubMed, Medline, CINAHL, DH data, and Embase databases was performed using the following keywords: mountain, biking and injuries. This revealed 2 review articles, 17 case controlled studies, 4 case series and 5 case reports. This review summarises the published literature on mountain biking injuries, discusses injury frequency and common injury mechanisms. Riders are quick to adopt safety measures. Helmet usage is now increasingly common and handlebar adaptations have been discontinued. Although the sport has a reputation for speed and risk with research and awareness, injury prevention measures are being adopted making the sport as safe as possible.

  19. The Olympic Mountains Experiment (OLYMPEX)

    Energy Technology Data Exchange (ETDEWEB)

    Houze, Robert A. [University of Washington, Seattle, Washington; Pacific Northwest National Laboratory, Richland, Washington; McMurdie, Lynn A. [University of Washington, Seattle, Washington; Petersen, Walter A. [NASA Marshall Space Flight Center, Huntsville, Alabama; Schwaller, Mathew R. [NASA Goddard Space Flight Center, Greenbelt, Maryland; Baccus, William [Olympic National Park, Port Angeles, Washington; Lundquist, Jessica D. [University of Washington, Seattle, Washington; Mass, Clifford F. [University of Washington, Seattle, Washington; Nijssen, Bart [University of Washington, Seattle, Washington; Rutledge, Steven A. [Colorado State University, Fort Collins, Colorado; Hudak, David R. [Environment and Climate Change Canada, King City, Ontario, Canada; Tanelli, Simone [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California; Mace, Gerald G. [University of Utah, Salt Lake City, Utah; Poellot, Michael R. [University of North Dakota, Grand Forks, North Dakota; Lettenmaier, Dennis P. [University of California, Los Angeles, Los Angeles, California; Zagrodnik, Joseph P. [University of Washington, Seattle, Washington; Rowe, Angela K. [University of Washington, Seattle, Washington; DeHart, Jennifer C. [University of Washington, Seattle, Washington; Madaus, Luke E. [National Center for Atmospheric Research, Boulder, Colorado; Barnes, Hannah C. [Pacific Northwest National Laboratory, Richland, Washington

    2017-10-01

    the Olympic Mountains Experiment (OLYMPEX) took place during the 2015-2016 fall-winter season in the vicinity of the mountainous Olympic Peninsula of Washington State. The goals of OLYMPEX were to provide physical and hydrologic ground validation for the U.S./Japan Global Precipitation Measurement (GPM) satellite mission and, more specifically, to study how precipitation in Pacific frontal systems is modified by passage over coastal mountains. Four transportable scanning dual-polarization Doppler radars of various wavelengths were installed. Surface stations were placed at various altitudes to measure precipitation rates, particle size distributions, and fall velocities. Autonomous recording cameras monitored and recorded snow accumulation. Four research aircraft supplied by NASA investigated precipitation processes and snow cover, and supplemental rawinsondes and dropsondes were deployed during precipitation events. Numerous Pacific frontal systems were sampled, including several reaching "atmospheric river" status, warm and cold frontal systems, and postfrontal convection

  20. Revegetation and management of tailings sand slopes from tar sand extraction: 1978 results

    Energy Technology Data Exchange (ETDEWEB)

    Rowell, M J

    1979-01-01

    The results are reported of research into the revegetation of two areas on a steeply sloping dike composed of tailings sand from tar sand extraction at the Great Canadian Oil Sand Limited plant at Fort McMurray, Alberta. One area was seeded with three pasture grasses and two legumes in 1971 after the slope surface had been mixed with peat to a depth of 15 cm. A second area had been amended with peat or peat and overburden and differing rates of fertilizer added. A mix containing nine grasses, four legumes, and oats, as a companion crop, was seeded in July 1976. The objectives of the research were to study methods for the establishment of a stable vegetative cover that would prevent erosion of the slope and, in time, might become a self maintaining unit. Tillage of soil amendments to a depth of 15 cm and 30 cm were compared in promoting deeper rooting and stabilizing of the slope.

  1. Yucca Mountain project prototype testing

    International Nuclear Information System (INIS)

    Hughes, W.T.; Girdley, W.A.

    1990-01-01

    The U.S. DOE is responsible for characterizing the Yucca Mountain site in Nevada to determine its suitability for development as a geologic repository to isolate high-level nuclear waste for at least 10,000 years. This unprecedented task relies in part on measurements made with relatively new methods or applications, such as dry coring and overcoring for studies to be conducted from the land surface and in an underground facility. The Yucca Mountain Project has, since 1988, implemented a program of equipment development and methods development for a broad spectrum of hydrologic, geologic, rock mechanics, and thermomechanical tests planned for use in an Exploratory Shaft during site characterization at the Yucca Mountain site. A second major program was fielded beginning in April 1989 to develop and test methods and equipment for surface drilling to obtain core samples from depth using only air as a circulating medium. The third major area of prototype testing has been during the ongoing development of the Instrumentation/ Data Acquisition System (IDAS), designed to collect and monitor data from down-hole instrumentation in the unsaturated zone, and store and transmit the data to a central archiving computer. Future prototype work is planned for several programs including the application of vertical seismic profiling methods and flume design to characterizing the geology at Yucca Mountain. The major objectives of this prototype testing are to assure that planned Site Characterization testing can be carried out effectively at Yucca Mountain, both in the Exploratory Shaft Facility (ESF), and from the surface, and to avoid potential major failures or delays that could result from the need to re-design testing concepts or equipment. This paper will describe the scope of the Yucca Mountain Project prototype testing programs and summarize results to date. 3 figs

  2. Phase I Cultural Resources Survey and Archeological Inventory of a Proposed 1.12 ha (2.87 ac) Borrow Pit and an Associated Access Road, Ascension Parish, Louisiana

    Science.gov (United States)

    2004-10-01

    few cally grown sugar cane into molasses (Fossier sugar plantations are formed in the parish of 1957:47). Solis, and later Mendez , who pur...Recreation and Tourism, Office of Cultural Development, Division of Ar- chaeology, Baton Rouge, Louisiana. Speaker, John Stuart, Joanna Chase, Carol

  3. W.A. Parish Post-Combustion CO{sub 2} Capture and Sequestration Project Phase 1 Definition

    Energy Technology Data Exchange (ETDEWEB)

    Armpriester, Anthony; Smith, Roger; Scheriffius, Jeff; Smyth, Rebecca; Istre, Michael

    2014-02-01

    For a secure and sustainable energy future, the United States (U.S.) must reduce its dependence on imported oil and reduce its emissions of carbon dioxide (CO{sub 2}) and other greenhouse gases (GHGs). To meet these strategic challenges, the U.S. wiU have to create fundamentally new technologies with performance levels far beyond what is now possible. Developing advanced post-combustion clean coal technologies for capturing CO{sub 2} from existing coal-fired power plants can play a major role in the country's transition to a sustainable energy future, especially when coupled with CO{sub 2}-enhanced oil recovery (CO{sub 2}-EOR). Pursuant to these goals, NRG Energy, Inc. (NRG) submitted an application and entered into a cost-shared collaboration with the U.S. Department of Energy (DOE) under Round 3 of the Clean Coal Power Initiative (CCPI) to advance low-emission coal technologies. The objective of the NRG W A Parish Post-Combustion CO{sub 2} Capture and Sequestration Demonstration Project is to establish the technical feasibility and economic viability of post-combustion CO{sub 2} capture using flue gas from an existing pulverized coal-fired boiler integrated with geologic sequestration via an enhanced oil recovery (EOR) process. To achieve these objectives, the project will be executed in three phases. Each phase represents a distinct aspect of the project execution. The project phases are: • Phase I. Project Definition/Front-End Engineering Design (FEED) • Phase ll. Detailed Engineering, Procurement & Construction • Phase III. Demonstration and Monitoring The purpose of Phase I is to develop the project in sufficient detail to facilitate the decision-making process in progressing to the next stage of project delivery. Phase n. This report provides a complete summary of the FEED study effort, including pertinent project background information, the scope of facilities covered, decisions, challenges, and considerations made regarding configuration and

  4. Mountain Warfare: The Need for Specialist Training

    National Research Council Canada - National Science Library

    Malik, Muhammad

    2003-01-01

    This study focuses on the need for specialist training for mountain warfare. It analyzes the special characteristics of mountain and high altitude terrain which affect conduct of military operations...

  5. Properties of dune sand concrete containing coffee waste

    Directory of Open Access Journals (Sweden)

    Mohamed Guendouz

    2018-01-01

    Full Text Available In the last years, an increase of coffee beverages consumption has been observed all over the world; and its consumption increases the waste coffee grounds which will become an environmental problems. Recycling of this waste to produce new materials like sand concrete appears as one of the best solutions for reduces the problem of pollution. This work aims to study the possibility of recycling waste coffee grounds (Spent Coffee Grounds (SCG as a fine aggregate by replacing the sand in the manufacturing of dune sand concrete. For this; sand concrete mixes were prepared with substitution of sand with the spent coffee grounds waste at different percentage (0%, 5%, 10%, 15% and 20% by volume of the sand in order to study the influence of this wastes on physical (Workability, bulk density and porosity, mechanical (compressive and flexural strength and Thermal (Thermal conductivity and thermal diffusivity properties of dune sand concrete. The results showed that the use of spent coffee grounds waste as partial replacement of natural sand contributes to reduce workability, bulk density and mechanical strength of sand concrete mixes with an increase on its porosity. However, the thermal characteristics are improved and especially for a level of 15% and 20% of substitution. So, it is possible to obtain an insulating material which can be used in the various types of structural components. This study ensures that reusing of waste coffee grounds in dune sand concrete gives a positive approach to reduce the cost of materials and solve some environmental problems.

  6. Policy Analysis of the Canadian Oil Sands Experience

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2013-09-01

    For those who support U.S. oil sands development, the Canadian oil sands industry is often identified as a model the U.S. might emulate, yielding financial and energy security benefits. For opponents of domestic oil sands development, the Canadian oil sands experience illustrates the risks that opponents of development believe should deter domestic policymakers from incenting U.S. oil sands development. This report does not seek to evaluate the particular underpinnings of either side of this policy argument, but rather attempts to delve into the question of whether the Canadian experience has relevance as a foundational model for U.S. oil sands development. More specifically, this report seeks to assess whether and how the Canadian oil sands experience might be predictive or instructive in the context of fashioning a framework for a U.S. oil sands industry. In evaluating the implications of these underpinnings for a prospective U.S. oil sands industry, this report concentrates on prospective development of the oil sands deposits found in Utah.

  7. Changes in active eolian sand at northern Coachella Valley, California

    Science.gov (United States)

    Katra, Itzhak; Scheidt, Stephen; Lancaster, Nicholas

    2009-04-01

    Climate variability and rapid urbanization have influenced the sand environments in the northern Coachella Valley throughout the late 20th century. This paper addresses changes in the spatial relationships among different sand deposits at northern Coachella Valley between two recent time periods by using satellite data acquired from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER). The approach employed here, involving multispectral thermal infrared (TIR) data and spectral mixture analysis, has shown that the major sand deposits can be spatially modeled at northern Coachella Valley. The "coarse-grained (quartz-rich) sand" deposit is associated with active eolian sand, and the "mixed sandy soil" and "fine-grained (quartz-rich) sand" deposits are associated with inactive eolian sand. The fractional abundance images showed a significant decrease between 2000 and 2006 in the percentage of active sand in the major depositional area for fluvial sediment, the Whitewater River, but also in two downwind areas: the Whitewater and Willow Hole Reserves. The pattern of the active sand appears to be related to variations in annual precipitation (wet and dry years) and river discharge in the northern Coachella Valley. We suggest here that recent human modifications to the major watercourses that supply sand affect the capability of fluvial deposition areas to restore sediments over time and consequently the responses of the sand transport system to climate change, becoming more sensitive to dry years where areas of active sand may shrink, degrade, and/or stabilize faster. The approach utilized in this study can be advantageous for future monitoring of sand in the northern Coachella Valley for management of these and similar environments.

  8. Asian interests in Alberta oil sands

    International Nuclear Information System (INIS)

    Du Plessis, D.; Laureshen, C.

    2004-01-01

    The growing Asian interest in Alberta's oil sands and import opportunities was discussed along with the feasibility of marketing bitumen to Asia. Asia is an obvious new market for Canadian heavy oil and bitumen due to an increasing demand for petroleum products in Japan, Korea, Taiwan and China. This paper examined the following three criteria that will determine the success of any initiative to move Canadian crude oil to Asian-Pacific markets: (1) a sustainable supply from Alberta; a pipeline to transport the crude to a deepwater port on the west coast; and, a guaranteed market at the other end. The basis for Asian interest in Alberta's oil sands is the sustainable secure supply of oil for growing Asian markets; heavy dependence on supplies from the Middle East; the desire to diversify supply sources; and, opportunities to invest in oil sands developments. Examples of Asian (Japan, Korea, Taiwan and China) missions to Alberta were presented along with the challenges of getting products to market with reference to Enbridge's new market access plan, Terasen's staged capacity expansion for heavy crudes and refined products, and sea transport from Prince Rupert. The paper also included graphs depicting world GDP; incremental increase in world primary energy demand by fuel for 2000 to 2020; world oil demand by region; oil demand by region in Asia; oil demand and supply in northeast Asia (Japan, China, Korea) and dependence level on Middle Eastern oil; oil demand and supply in China; China's petroleum production and consumption; refined products market forecast for 2000 to 2020; 2002 crude oil imports to Asia; 2004 refining capacity; product quality comparisons; cost competitive study; and energy policy objectives for China, Japan, Korea and Taiwan. 19 figs

  9. Radiometric Characterization of Sand in Northeast Sinai

    International Nuclear Information System (INIS)

    Ramadan, Kh.A.; Badran, H.M.; Ramadan, Kh.A.; Seddeek, M.K.; Sharshar, T.

    2009-01-01

    Thirty-eight locations covering an area of 350 km 2 in northeast Sinai were investigated by gamma-ray spectroscopy using a 50% HPGe detector. The limits of area are Al-Arish North, El-Hasana South, El-Oga East, and El- Gifgafa West. The range of activity concentrations of 238 U, 234 Th, 226 Ra, 232 Th and 40 K are 0.6-35.2, 3.9-22.6, 4.7-29.6, 4.7-23.9, and 108-295 Bq/kg for sands, respectively. 137 Cs in the region ranged from 0.1-8.0 Bq/kg. No major difference between the studied area and that previously investigated in the costal area in North Sinai. Reliable correlations (R2 = 0.8-0.9) among 238 U, 234 Th, and 226 Ra isotopes was obtained. On the other hand, low correlation (R 2 = 0.6-0.7) was obtained from the analysis of the isotopes of 238 U-seies and 232 Th. No evidence of correlation between the concentrations of radioisotopes and pH contents, TOM, and grain size were found. The soil-plant transfer factor are 226 Ra and 232 Th, 40 K, and 137 Cs, respectively. The wild vegetations collected from the studied area have average concentrations of 1.9, 1.4, 1.3, 254, and 0.3 for 234 Th, 226 Ra, 232 Th, 40 K, and 137 Cs, respectively. The average concentrations of 226 Ra, 232 Th, and 40 K in water samples collected from five wells are 0.02, 0.02, and 1.1 Bq/l, respectively. The average absorbed dose rate for the sand samples were calculated to be 19.4 n Gy h-1. The Raeq activities of the sands are lower than the recommended maximum value of 370 Bq kg-1 criterion limit of Raeq activity for building materials

  10. Western Gas Sands Project status report

    Energy Technology Data Exchange (ETDEWEB)

    Atkinson, C.H.

    1978-11-30

    Progress of government-sponsored projects directed toward increasing gas production from the low-permeability gas sands of the western United States is summarized. A Technology Implementation Plan (TIP) meeting was held at the CER office in Las Vegas, Nevada, October 16--19 to initiate the implementation phase of the Enhanced Gas Recovery (EGR) working group activities. A WGSP Logging Program meeting was conducted on October 24, 1978, at CER offices to define the problems associated with logs in tight gas sands. CER personnel and the project manager attended a two-day course on the fundamentals of core and reservoir analysis in Denver, Colorado, and met with USGS personnel to discuss USGS work on the WGSP. A meeting was held to discuss a contract for coring a Twin Arrow well on the Douglas Creek Arch, Colorado. CER Corporation personnel attended the Geological Society of America Annual Meeting held in Toronto, Canada, October 23--27 and a Gas Stimulation Workshop at Sandia Laboratories in Albuquerque, New Mexico, October 11 and 12 to discuss recent mineback experiments conducted at the Nevada Test Site. Fiscal year 1979 projects initiated by USGS and the Energy Technology Centers and National Laboratories are progressing as scheduled. Mobil Research and Development Corporation fractured zone 8 of the F-31-13G well in Rio Blanco County, Colorado. Colorado Interstate Gas Company poured the concrete pad for the compresser expected to be delivered in December and were laying pipeline between the wells at month end. The Mitchell Energy well, Muse Duke No. 1 was flowing on test at a rate of 2,100 Mcfd and preparations proceeded to fracture the well on November 15 with approximately 1,000,000 gal of fluid and 3,000,000 lb of sand. Terra Tek completed laboratory analyses of cores taken from the Mitchell Energy well.

  11. Radiogenic heavy minerals in Brazilian beach sand

    International Nuclear Information System (INIS)

    Malanca, A.

    1998-01-01

    Sand samples collected on the beaches of the 'radioactive' Brazilian town of Guarapari were first separated by flotation in bromoform and successively divided into various magnetic fractions with a Franz isodynamic separator. concentrations of background radionuclides in samples of monazite, ilmenite, and zircon were determined by a γ-ray spectrometer. Chemical composition of monazite, ilmenite and magnetite were assessed by means of an electron microprobe. Monazite resulted to be relatively rich in ThO 2 whose abundance ranged from 5.3 to 7.7 (wt%). (author)

  12. Limitation of releases and filtration by sand

    International Nuclear Information System (INIS)

    Schektman, N.

    1986-01-01

    In the highly hypothetic case of a severe reactor accident, it may lead to an increase of pressure within the containment and up to a value above the calculated pressure. A procedure is necessary in this case to maintain the integrity of the containment to prevent a release of radioactive products to the environment, while controlling in the best way releases. So, EDF and the CEA have developed a device of decompression-filtration of the containment atmosphere, using a free penetration of the containment and a sand box; the device and its operation constitute the U5 procedure [fr

  13. Sphere impact and penetration into wet sand

    KAUST Repository

    Marston, J. O.

    2012-08-07

    We present experimental results for the penetration of a solid sphere when released onto wet sand. We show, by measuring the final penetration depth, that the cohesion induced by the water can result in either a deeper or shallower penetration for a given release height compared to dry granular material. Thus the presence of water can either lubricate or stiffen the granular material. By assuming the shear rate is proportional to the impact velocity and using the depth-averaged stopping force in calculating the shear stress, we derive effective viscosities for the wet granular materials.

  14. Prolífica George Sand

    Directory of Open Access Journals (Sweden)

    Àngels Santa

    2014-04-01

    Full Text Available A propósito de las obras de George Sand, Œuvres complètes. Sous la direction de Béatrice Didier. 1841-1842.Un hiver à Majorque. Édition critique par Angela Ryan. Horace.Édition critique par Jeanne Brunereau (París, Honoré Champion, 2013, 748 p. ISBN : 9782745319265 y Œuvres complètes. ́Sous la direction de Béatrice Didier. 1849.La petite Fadette. Édition critique par Andrée Mansau (París, Honoré Champion, 2013, 345p. ISBN : 9782745319203

  15. Investigation of Sand-Cement Grouts

    Science.gov (United States)

    1960-09-01

    I -IEN NO Isis Table 1 InvestiiatLon of Sand-Cement Crouts Data on Lhe Physical Properties of the inely Divided Mineral Admixt)res Blaine Specific...Itoi, tuicrlt.nel, Caiftrnia; fl1; aish, Illinois; ;1iaricito, California; Lo’ss, Yisniasi~pi; bentornitoe, Wy~caing. Physical drnta for the raateriais...increase i’: tne a.cunt of .anj th-?t coul be puiped. As the diatomite had a specific ,i’face about 1C tines that of the loe33, it would appear that this

  16. SandBlaster: Reversing the Apple Sandbox

    OpenAIRE

    Deaconescu, Răzvan; Deshotels, Luke; Bucicoiu, Mihai; Enck, William; Davi, Lucas; Sadeghi, Ahmad-Reza

    2016-01-01

    In order to limit the damage of malware on Mac OS X and iOS, Apple uses sandboxing, a kernel-level security layer that provides tight constraints for system calls. Particularly used for Apple iOS, sandboxing prevents apps from executing potentially dangerous actions, by defining rules in a sandbox profile. Investigating Apple's built-in sandbox profiles is difficult as they are compiled and stored in binary format. We present SandBlaster, a software bundle that is able to reverse/decompile Ap...

  17. Heating tar sands formations while controlling pressure

    Science.gov (United States)

    Stegemeier, George Leo [Houston, TX; Beer, Gary Lee [Houston, TX; Zhang, Etuan [Houston, TX

    2010-01-12

    Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. A pressure in the majority of the section may be maintained below a fracture pressure of the formation. The pressure in the majority of the section may be reduced to a selected pressure after the average temperature reaches a temperature that is above 240.degree. C. and is at or below pyrolysis temperatures of hydrocarbons in the section. At least some hydrocarbon fluids may be produced from the formation.

  18. Heating tar sands formations to visbreaking temperatures

    Science.gov (United States)

    Karanikas, John Michael [Houston, TX; Colmenares, Tulio Rafael [Houston, TX; Zhang, Etuan [Houston, TX; Marino, Marian [Houston, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Ryan, Robert Charles [Houston, TX; Beer, Gary Lee [Houston, TX; Dombrowski, Robert James [Houston, TX; Jaiswal, Namit [Houston, TX

    2009-12-22

    Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat may be controlled so that at least a majority of the section reaches an average temperature of between 200.degree. C. and 240.degree. C., which results in visbreaking of at least some hydrocarbons in the section. At least some visbroken hydrocarbon fluids may be produced from the formation.

  19. Sphere impact and penetration into wet sand

    KAUST Repository

    Marston, J. O.; Vakarelski, Ivan Uriev; Thoroddsen, Sigurdur T

    2012-01-01

    We present experimental results for the penetration of a solid sphere when released onto wet sand. We show, by measuring the final penetration depth, that the cohesion induced by the water can result in either a deeper or shallower penetration for a given release height compared to dry granular material. Thus the presence of water can either lubricate or stiffen the granular material. By assuming the shear rate is proportional to the impact velocity and using the depth-averaged stopping force in calculating the shear stress, we derive effective viscosities for the wet granular materials.

  20. A mountain of millipedes I

    DEFF Research Database (Denmark)

    Enghoff, Henrik

    2014-01-01

    Twenty new species of the millipede genus Chaleponcus Attems, 1914, are described from the Udzungwa Mountains: C. netus sp. nov., C. quasimodo sp. nov., C. malleolus sp. nov., C. scopus sp. nov., C. nikolajscharffi sp. nov., C. mwanihanensis sp. nov., C. basiliscus sp. nov., C. krai sp. nov., C...

  1. Soil variability in mountain areas

    OpenAIRE

    Zanini, E.; Freppaz, M.; Stanchi, S.; Bonifacio, E.; Egli, M.

    2015-01-01

    The high spatial variability of soils is a relevant issue at local and global scales, and determines the complexity of soil ecosystem functions and services. This variability derives from strong dependencies of soil ecosystems on parent materials, climate, relief and biosphere, including human impact. Although present in all environments, the interactions of soils with these forming factors are particularly striking in mountain areas.

  2. The Mountaineer-Malaysia Connection.

    Science.gov (United States)

    Young, Jeff

    1997-01-01

    A 26-day summer field course of West Virginia University's (WVU) Recreation and Parks Department took students to Malaysia's mountains and rainforests to observe how Malaysians are managing national parks, problem elephants, and population pressures on parks. The adventure provided powerful learning experiences. Further exchanges between WVU and…

  3. A mountain of millipedes V

    DEFF Research Database (Denmark)

    Enghoff, Henrik

    2016-01-01

    Three new genera of Odontopygidae are described, all based on new species from the Udzungwa mountains, Tanzania, and all monotypic: Casuariverpa gen. nov. (type species: C. scarpa gen. et sp. nov.), Yia gen. nov. (type species: Y. geminispina gen. et sp. nov.), and Utiliverpa gen. nov. (type spec...

  4. Mountain biking injuries: an update.

    Science.gov (United States)

    Kronisch, Robert L; Pfeiffer, Ronald P

    2002-01-01

    This article reviews the available literature regarding injuries in off-road bicyclists. Recent progress in injury research has allowed the description of several patterns of injury in this sport. Mountain biking remains popular, particularly among young males, although sales and participation figures have decreased in the last several years. Competition in downhill racing has increased, while cross-country racing has decreased somewhat in popularity. Recreational riders comprise the largest segment of participants, but little is known about the demographics and injury epidemiology of noncompetitive mountain cyclists. Most mountain bikers participating in surveys reported a history of previous injuries, but prospective studies conducted at mountain bike races have found injury rates of bike racing the risk of injury may be higher for women than men. Minor injuries such as abrasions and contusions occur frequently, but are usually of little consequence. Fractures usually involve the torso or upper extremities, and shoulder injuries are common. Head and face injuries are not always prevented by current helmet designs. Fatal injuries are rare but have been reported. Improvements in safety equipment, rider training and racecourse design are suggested injury prevention measures. The authors encourage continued research in this sport.

  5. Gearing Up for Mountain Biking.

    Science.gov (United States)

    Jahnke, Thomas; Hamson, Mike

    1999-01-01

    Examines the gear system of a mountain bike to discover any redundancy in the many gear settings available to the cyclist. Suggests a best strategy for changing up through the gears on a typical 21-gear system and an adjustment to the available gears that would result in a smoother change. (Author/ASK)

  6. A mountain of millipedes III

    DEFF Research Database (Denmark)

    Enghoff, Henrik

    2016-01-01

    The new genus Geotypodon gen. nov. is described. It includes two species from the Udzungwa Mountains: G. millemanus gen. et sp. nov. (type species) and G. submontanus gen. et sp. nov., one species from nearby Iringa: G. iringensis gen. et sp. nov., and 18 previously described species hitherto...

  7. Rocky Mountain spotted fever, Panama.

    Science.gov (United States)

    Estripeaut, Dora; Aramburú, María Gabriela; Sáez-Llorens, Xavier; Thompson, Herbert A; Dasch, Gregory A; Paddock, Christopher D; Zaki, Sherif; Eremeeva, Marina E

    2007-11-01

    We describe a fatal pediatric case of Rocky Mountain spotted fever in Panama, the first, to our knowledge, since the 1950s. Diagnosis was established by immunohistochemistry, PCR, and isolation of Rickettsia rickettsii from postmortem tissues. Molecular typing demonstrated strong relatedness of the isolate to strains of R. rickettsii from Central and South America.

  8. Rocky Mountain spotted fever, Colombia.

    Science.gov (United States)

    Hidalgo, Marylin; Orejuela, Leonora; Fuya, Patricia; Carrillo, Pilar; Hernandez, Jorge; Parra, Edgar; Keng, Colette; Small, Melissa; Olano, Juan P; Bouyer, Donald; Castaneda, Elizabeth; Walker, David; Valbuena, Gustavo

    2007-07-01

    We investigated 2 fatal cases of Rocky Mountain spotted fever that occurred in 2003 and 2004 near the same locality in Colombia where the disease was first reported in the 1930s. A retrospective serosurvey of febrile patients showed that > 21% of the serum samples had antibodies aaainst spotted fever group rickettsiae.

  9. Assessment of sand quality on concrete performance : examination of acidic and sulfate/sulfide-bearing sands.

    Science.gov (United States)

    2014-12-01

    The purpose of this research is to examine how the presence of sulfide- and sulfate-containing : minerals in acidic aggregates may affect the properties of mortar and concrete. Analyses were : performed to compare two sands from a deposit in the Geor...

  10. Oil sands to the rescue: oil sand microbial communities can degrade recalcitrant alkyl phenyl alkanoic acids

    Energy Technology Data Exchange (ETDEWEB)

    Whitby, Corinne [University of Essex (Canada)], email: cwhitby@essex.ac.uk

    2011-07-01

    Almost half of all global oil reserves are found as biodegraded heavy oils found in vast tar sand deposits located in North and South America and these account for 47% of Canadian oil production. Oil sand extraction generates large amounts of toxic waste water, known as oil sand process waters (OSPW), that are stored in large tailing ponds that contain toxic compounds like naphthenic acids (NAs). The presence of NAs creates problems like toxicity, corrosion, and the formation of calcium napthenate deposits which block pipelines and other infrastructure and need to be removed. This paper presents oil sand microbial communities that can degrade these NAs. The approach is to apply new aliphatic and aromatic NAs as substrates to supplement and identify NA degrading microbes and also to identify the metabolites produced and explain NA degradation pathways and the functional genes involved. The chemistry and the processes involved are explained. From the results, it is suggested that pure cultures of P. putida KT2440 be used against NAs.

  11. The stable stiffness triangle - drained sand during deformation cycles

    DEFF Research Database (Denmark)

    Sabaliauskas, Tomas; Ibsen, Lars Bo

    2017-01-01

    Cyclic, drained sand stiffness was observed using the Danish triaxial appa- ratus. New, deformation dependant soil property (the stable stiffness triangle) was detected. Using the the stable stiffness triangle, secant stiffness of drained sand was plausible to predict (and control) even during ir...... findings can find application in off-shore, seismic and other engi- neering practice, or inspire new branches of research and modelling wherever dynamic, cyclic or transient loaded sand is encountered....

  12. Evaluation of sand reserves in del Plata City

    International Nuclear Information System (INIS)

    Loureiro, J.

    2014-01-01

    The purpose of this study is to evaluate the reserve of sand in the zone of del Plata city and beyond. This area is located in the S E edge of the department of San Jose near the mouth of Santa Lucia river. In this zone was identified the mantle of potentially exploitable sand which are based on their particle size, composition and depth of the limits cape. There are two powerful capes of sand separated by clay and silt

  13. Final report on Thermally Modified Sand demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    1994-09-23

    The use of salt and salt/sand mixtures on icy roadway surfaces has dramatically increased during the past 30 years. Despite extensive documentation on salt related damage to the roadway improvements, vehicles and the environment, road maintenance departments have continued to rely on this practice. Road maintenance departments in northern climate areas have long recognized the safety benefits for public mobility on icy roadways from the use of sand. As an abrasive material, the sand improves the surface traction that results in more drivable and less hazardous road conditions during the winter months. Stockpiles of pure sand stored during the winter months oftentimes freeze into large unworkable, monolithic piles. To maintain a free-flowing condition, it has been found to be necessary to add salt to the sand. The addition of salt in amounts ranging from 5 to 10 percent to that of sand, is usually sufficient to provide relatively free-flowing abrasive material that could be stored in stockpiles and applied to icy road surfaces with conventional sand spreading trucks. Another alternative for winter storage of pure sand to maintain a free-flowing condition is in humidity-controlled, heated buildings. As would be expected, this method has high capital and operating costs. and not cost effective for general highway maintenance use. The invention demonstrated herein is a method of thermally modifying pure sand that will remain in a free-flowing state throughout the winter season without the need for the salt additive. The thermally modified sand provides an abrasive material that when applied to icy roads does not cause environmental and corrosive damage as done by the application of sand with salt. By employing a very simple process of freezing screened sand particles by forced air convection under subfreezing conditions, the invention creates a product that has significant value in terms of economic and environmental benefits.

  14. Relationships between sand and water quality at recreational beaches.

    Science.gov (United States)

    Phillips, Matthew C; Solo-Gabriele, Helena M; Piggot, Alan M; Klaus, James S; Zhang, Yifan

    2011-12-15

    Enterococci are used to assess the risk of negative human health impacts from recreational waters. Studies have shown sustained populations of enterococci within sediments of beaches but comprehensive surveys of multiple tidal zones on beaches in a regional area and their relationship to beach management decisions are limited. We sampled three tidal zones on eight South Florida beaches in Miami-Dade and Broward counties and found that enterococci were ubiquitous within South Florida beach sands although their levels varied greatly both among the beaches and between the supratidal, intertidal and subtidal zones. The supratidal sands consistently had significantly higher (p sand) than the other two zones. Levels of enterococci within the subtidal sand correlated with the average level of enterococci in the water (CFU/100mL) for the season during which samples were collected (r(s) = 0.73). The average sand enterococci content over all the zones on each beach correlated with the average water enterococci levels of the year prior to sand samplings (r(s) = 0.64) as well as the average water enterococci levels for the month after sand samplings (r(s) = 0.54). Results indicate a connection between levels of enterococci in beach water and sands throughout South Florida's beaches and suggest that the sands are one of the predominant reservoirs of enterococci impacting beach water quality. As a result, beaches with lower levels of enterococci in the sand had fewer exceedences relative to beaches with higher levels of sand enterococci. More research should focus on evaluating beach sand quality as a means to predict and regulate marine recreational water quality. Copyright © 2011 Elsevier Ltd. All rights reserved.

  15. Evaluation of Augmented REality Sandtable (ARES) during Sand Table Construction

    Science.gov (United States)

    2018-01-01

    sand table, ARES, resulted in significantly higher- quality ratings overall for the terrain model based on a global rating scale, as well as...dependent measures in this study. Sand Table Construction Score Card: A 5-point Likert scale was used to identify the accuracy and quality of required...reproduced on the sand table. The quality of the map reproduced was evaluated using standard procedures of the map-drawing paradigm, such as that

  16. White Sands, New Mexico as seen from STS-60

    Science.gov (United States)

    1994-01-01

    White Sands National Monument (Park) is easily recognized in the center of this near-vertical color photograph. White Sands is the world's largest gypsum dune field. It represents an alabaster sea that covers nearly 300 square miles. At the southwest corner of the White Sands is dry lake, Lucero. In terms of cultural features the city of Alamogordo and Holloman Air Force Base can be seen with great clarity on this photograph.

  17. Production and global transport of Titan's sand particles

    Science.gov (United States)

    Barnes, Jason W.; Lorenz, Ralph D.; Radebaugh, Jani; Hayes, Alexander G.; Arnold, Karl; Chandler, Clayton

    2015-06-01

    Previous authors have suggested that Titan's individual sand particles form by either sintering or by lithification and erosion. We suggest two new mechanisms for the production of Titan's organic sand particles that would occur within bodies of liquid: flocculation and evaporitic precipitation. Such production mechanisms would suggest discrete sand sources in dry lakebeds. We search for such sources, but find no convincing candidates with the present Cassini Visual and Infrared Mapping Spectrometer coverage. As a result we propose that Titan's equatorial dunes may represent a single, global sand sea with west-to-east transport providing sources and sinks for sand in each interconnected basin. The sand might then be transported around Xanadu by fast-moving Barchan dune chains and/or fluvial transport in transient riverbeds. A river at the Xanadu/Shangri-La border could explain the sharp edge of the sand sea there, much like the Kuiseb River stops the Namib Sand Sea in southwest Africa on Earth. Future missions could use the composition of Titan's sands to constrain the global hydrocarbon cycle.

  18. Trajectories of saltating sand particles behind a porous fence

    Science.gov (United States)

    Zhang, Ning; Lee, Sang Joon; Chen, Ting-Guo

    2015-01-01

    Trajectories of aeolian sand particles behind a porous wind fence embedded in a simulated atmospheric boundary layer were visualized experimentally, to investigate the shelter effect of the fence on sand saltation. Two sand samples, one collected from a beach (d = 250 μm) and the other from a desert (d = 100 μm), were tested in comparison with the previous studies of a 'no-fence' case. A wind fence (ε = 38.5%) was installed on a flat sand bed filled with each sand sample. A high-speed photography technique and the particle tracking velocimetry (PTV) method were employed to reconstruct the trajectories of particles saltating behind the fence. The collision processes of these sand particles were analyzed, momentum and kinetic energy transfer between saltating particles and ground surface were also investigated. In the wake region, probability density distributions of the impact velocities agree well with the pattern of no-fence case, and can be explained by a log-normal law. The horizontal component of impact velocity for the beach sand is decreased by about 54%, and about 76% for the desert sand. Vertical restitution coefficients of bouncing particles are smaller than 1.0 due to the presence of the wind fence. The saltating particles lose a large proportion of their energy during the collision process. These results illustrate that the porous wind fence effectively abates the further evolution of saltating sand particles.

  19. Numerical simulation of flow and compression of green sand

    DEFF Research Database (Denmark)

    Hovad, Emil

    The focus of the industrial PhD project was concentrated on the production of the sand mold (green sand) which gives the cast component its final geometrical shape. In order to ensure a high quality of the cast component, it is important to control the manufacturing process of the mold itself so...... that it is homogeneous and stable. Therefore gaining a basic understanding of how the flow and deposition of green sand should be characterized and modelled was important, so that it could be used for simulation of the manufacturing process of the sand mold. The flowability of the green sand is important when the sand...... flows down through the hopper filling the chamber with sand during the sand shot. The flowability of green sand is mostly governed by the amount of water and bentonite which both decrease it. The flowability and the internal forces thus control how well you can fill a complex mold geom-etry in which...

  20. An investigation of waste foundry sand in asphalt concrete mixtures.

    Science.gov (United States)

    Bakis, Recep; Koyuncu, Hakan; Demirbas, Ayhan

    2006-06-01

    A laboratory study regarding the reuse of waste foundry sand in asphalt concrete production by replacing a certain portion of aggregate with WFS was undertaken. The results showed that replacement of 10% aggregates with waste foundry sand was found to be the most suitable for asphalt concrete mixtures. Furthermore, the chemical and physical properties of waste foundry sand were analysed in the laboratory to determine the potential effect on the environment. The results indicated that the investigated waste foundry sand did not significantly affect the environment around the deposition

  1. Effective Laboratory Method of Chromite Content Estimation in Reclaimed Sands

    Directory of Open Access Journals (Sweden)

    Ignaszak Z.

    2016-09-01

    Full Text Available The paper presents an original method of measuring the actual chromite content in the circulating moulding sand of foundry. This type of material is applied for production of moulds. This is the case of foundry which most frequently perform heavy casting in which for the construction of chemical hardening mould is used, both the quartz sand and chromite sand. After the dry reclamation of used moulding sand, both types of sands are mixed in various ratios resulting that in reclaimed sand silos, the layers of varying content of chromite in mixture are observed. For chromite recuperation from the circulating moulding sand there are applied the appropriate installations equipped with separate elements generating locally strong magnetic field. The knowledge of the current ratio of chromite and quartz sand allows to optimize the settings of installation and control of the separation efficiency. The arduous and time-consuming method of determining the content of chromite using bromoform liquid requires operational powers and precautions during using this toxic liquid. It was developed and tested the new, uncomplicated gravimetric laboratory method using powerful permanent magnets (neodymium. The method is used in the production conditions of casting for current inspection of chromite quantity in used sand in reclamation plant.

  2. Reuse of waste cutting sand at Lawrence Livermore National Laboratory

    International Nuclear Information System (INIS)

    Mathews, S.; Wilson, K.

    1998-01-01

    Lawrence Livermore National Laboratory (LLNL) examined the waste stream from a water jet cutting operation, to evaluate the possible reuse of waste garnet sand. The sand is a cutting agent used to shape a variety of materials, including metals. Nearly 70,000 pounds of waste sand is generated annually by the cutting operation. The Environmental Protection Department evaluated two potential reuses for the spent garnet sand: backfill in utility trenches; and as a concrete constituent. In both applications, garnet waste would replace the sand formerly purchased by LLNL for these purposes. Findings supported the reuse of waste garnet sand in concrete, but disqualified its proposed application as trench backfill. Waste sand stabilized in a concrete matrix appeared to present no metals-leaching hazard; however, unconsolidated sand in trenches could potentially leach metals in concentrations high enough to threaten ground water quality. A technical report submitted to the San Francisco Bay Regional Water Quality Control Board was reviewed and accepted by that body. Reuse of waste garnet cutting sand as a constituent in concrete poured to form walkways and patios at LLNL was approved

  3. Assessment of lake sensitivity to acidic deposition in national parks of the Rocky Mountains

    Science.gov (United States)

    Nanus, L.; Williams, M.W.; Campbell, D.H.; Tonnessen, K.A.; Blett, T.; Clow, D.W.

    2009-01-01

    The sensitivity of high-elevation lakes to acidic deposition was evaluated in five national parks of the Rocky Mountains based on statistical relations between lake acid-neutralizing capacity concentrations and basin characteristics. Acid-neutralizing capacity (ANC) of 151 lakes sampled during synoptic surveys and basin-characteristic information derived from geographic information system (GIS) data sets were used to calibrate the statistical models. The explanatory basin variables that were considered included topographic parameters, bedrock type, and vegetation type. A logistic regression model was developed, and modeling results were cross-validated through lake sampling during fall 2004 at 58 lakes. The model was applied to lake basins greater than 1 ha in area in Glacier National Park (n = 244 lakes), Grand Teton National Park (n = 106 lakes), Great Sand Dunes National Park and Preserve (n = 11 lakes), Rocky Mountain National Park (n = 114 lakes), and Yellowstone National Park (n = 294 lakes). Lakes that had a high probability of having an ANC concentration 3000 m, with 80% of the catchment bedrock having low buffering capacity. The modeling results indicate that the most sensitive lakes are located in Rocky Mountain National Park and Grand Teton National Park. This technique for evaluating the lake sensitivity to acidic deposition is useful for designing long-term monitoring plans and is potentially transferable to other remote mountain areas of the United States and the world.

  4. Mineral legislations applicable to beach sand industry

    International Nuclear Information System (INIS)

    D'Cruz, Eric

    2016-01-01

    India has got a wealth of natural resources in different geological environs and shoreline placers form an important constituent of the natural resources. Large reserves of beach sand minerals, viz. imenite, rutile, leucoxene, zircon, sillimanite, garnet and monazite are the economic minerals in the coastal and inland placer sands. In the federal structure of India, the State Governments are the owners of minerals located within their respective boundaries. The State Governments grant the mineral concessions for all the minerals located within the boundary of the State, under the provisions of the Acts and Rules framed for the purpose. Though the mineral wealth is under the control of the State, the power for framing the rules for the grant of mineral concessions vastly rest with the Central Government. Since mineral concessions are often granted for a longer duration of thirty to fifty years or more, a historical perspective of these rules are imperative in understanding the issues involved with BSM mining industry. Under the Govt. of India Act, 1935, Regulation of Mines and Oilfields and Mineral Development was kept under Federal control, declared by Federal Law. The word 'Federal' was substituted by the word 'Dominion' by the India (Provincial Constitution) Order, 1947. No legislation was, however, enacted in pursuance of above power until after Independence. However, the Govt. on India made the Mining Concession (Central) Rules, 1939 for regulating grants of prospecting license

  5. Integrated oil sands tailings pond water treatment

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Z. [Saskatchewan Research Council, Saskatoon, SK (Canada)

    2010-07-01

    This PowerPoint presentation discussed research currently being conducted to treat oil sands tailings pond water (TPW). The treatment of TPW is challenged by the high level of naphthenic acids (NAs), the slow settling rate of fine particulate materials, and the complex chemistry of the water. The treatment process consisted of bioflocculation, sludge blanket assisted clarification, ozonation, and oil sands coke assisted hybrid biodegradation. The aggregation and adsorption process bound small particles and cells together while also ensuring the passive uptake of pollutants using microbial masses. The mixed liquor then passed through a sludge blanket to ensure enhanced particle capture. An ozonation process was used to increase the biodegradability of the TPW as well as to increase the biodegradability of the residual NAs after ozonation. The process used a hybrid bioreactor that consisted of both suspended and fixed microbial communities. The coke served as a biofilm carrier for the waste. Further studies are being conducted to investigate the efficiency and capability of the process. tabs., figs.

  6. Ilmenite Mineral's Recovery from Beach Sand Tailings

    International Nuclear Information System (INIS)

    Mulaba-Bafubiandi, Antoine F.; Mukendi-Ngalula, David; Waanders, Frans B.

    2002-01-01

    The mineral ilmenite is the major source of rutile for industrial use and is of interest to paint and fertiliser industries. Enormous unutilised tailing dams lie on the eastern coast of the South Africa. Although covered by a simulation of the original indigenous vegetation, these tailings are still ilmenite bearing and of economic value. Tailings emanating from beach sand mineral slimes dams of the Kwazulu-Natal area (South Africa) have been processed. Screening, flotation, spiral concentration and magnetic separation methods were used either separately or successively. The present work sheds light on alternative routes for the extraction of the ilmenite, from these tailings. It moreover points out the usefulness of the Moessbauer spectroscopy in the mineral processing product monitoring. Tailings from the beach sands were used in the present study after the economic industrial minerals zirconia, ilmenite and rutile had been extracted in previous mining operations. About 61% natural ilmenite recovery was observed in the flotation concentrate of a Humphrey Spiral concentrate while a 62% recovery of hematite was found in the flotation tailings. The combination of screening, spiral concentration and magnetic separation, and flotation yielded a product with the highest ilmenite and hematite concentration being 71% and 19%, respectively. A natural ilmenite mineral, containing 87% ilmenite and 13% hematite, could be produced and extracted from the tailings of the flotation process, collected subsequently to the spiral concentration and the initial screening.

  7. Avalanches of Singing Sand in the Laboratory

    Science.gov (United States)

    Dagois-Bohy, Simon; Courrech Du Pont, Sylvain; Douady, Stéphane

    2011-03-01

    The song of dunes is a natural phenomenon that has arisen travellers' curiosity for a long time, from Marco Polo to R.A. Bagnold. Scientific observations in the XXth century have shown that the sound is emitted during a shear flow of these particular grains, the free surface of the flow having coherent vibrations like a loud speaker. The sound emission is also submitted to a threshold effect with many parameters like humidity, flow speed, surface of the grains. The sound has been reproduced in laboratory avalanche experiments close to the natural phenomenon on field, but set in a channel with a hard bottom and a few centimeters of sand flowing, which contradicts explanations of the sound that involve a sand dune under the avalanche flow. Flow rates measurements also show the presence of a plug region in the flow above the sheared band, with the same characteristic length as the coherence zones of the sound. Finally we show experimentally that the Froude number, once modified to take into account the height of this plug band, is the parameter that sets the amplitude of the sound, and produces a threshold that depends on the grain type.

  8. Soil mixing of stratified contaminated sands.

    Science.gov (United States)

    Al-Tabba, A; Ayotamuno, M J; Martin, R J

    2000-02-01

    Validation of soil mixing for the treatment of contaminated ground is needed in a wide range of site conditions to widen the application of the technology and to understand the mechanisms involved. Since very limited work has been carried out in heterogeneous ground conditions, this paper investigates the effectiveness of soil mixing in stratified sands using laboratory-scale augers. This enabled a low cost investigation of factors such as grout type and form, auger design, installation procedure, mixing mode, curing period, thickness of soil layers and natural moisture content on the unconfined compressive strength, leachability and leachate pH of the soil-grout mixes. The results showed that the auger design plays a very important part in the mixing process in heterogeneous sands. The variability of the properties measured in the stratified soils and the measurable variations caused by the various factors considered, highlighted the importance of duplicating appropriate in situ conditions, the usefulness of laboratory-scale modelling of in situ conditions and the importance of modelling soil and contaminant heterogeneities at the treatability study stage.

  9. [Imperial Oil's Cold Lake oil sands operations

    International Nuclear Information System (INIS)

    Dingle, H. B.

    1999-01-01

    Imperial Oil Limited's Cold Lake oil sands resources, production and operations in Alberta are discussed. Cold Lake is the company's largest single asset and its largest source of crude oil production. In 1998, Cold Lake accounted for just under half of Imperial's total liquid production, averaging more than 135,000 barrels of bitumen a day. Despite the very difficult operating conditions experienced by the oil sands industry in 1998, Imperial Oil's Cold Lake operations generated a positive cash flow and earnings. Just as important, the near and long-term potential of Cold Lake property continues to be strong, even with the tough market conditions today and the foreseeable future. Proved reserves at the end of 1997 were 1.3 billions barrels, equal to about 24 years of current production, but even more important is Imperial's resource base in the Athabasca region, which represents 150 years of production at current rates. Although production forecasts for the near future are are revised downward because of production shut-in due to low prices, the company is confident of its long-term prospects mainly because of existing infrastructure, superior reservoir quality, 30 years worth of operating improvements and established bitumen-blend markets. Details of the company's future Cold Lake development plans are discussed. The need to continue technology development, which has been at the core of the industry's growth in the past and will continue to be the key to the future, are emphasized

  10. Enabling technologies for oil sands development

    International Nuclear Information System (INIS)

    Bailey, R.T.

    1998-01-01

    A review of oil sands production and expansion possibilities in Alberta were presented. The enabling technologies for oil sands projects include mining (bucketwheels, draglines, trucks, shovels conveyors, slurry hydrotransport); extraction (conditioning tumblers, pipelines, tanks, hot water, caustic, cold water, frothers); froth cleaning (centrifuges, solvent treatment); tailings (tailings ponds, consolidated tailings); and upgrading (coking, hydrotreating for SCO, hydrocracking and multiple products). The enabling technologies for in situ production include cyclic steam stimulation for vertical wells, steam assisted gravity drainage (SAGD) for dual horizontal wells, and cold production with wormholes. This paper described the recovery potentials of each of these processes. It also discussed the role of government and industry in research and cooperative research involving both the private and public sectors. Examples of each of these were described such as SAGD, the OSLO cold water extraction process, The consolidated tailings (CT) project, the low energy extraction process (slurry production, hydrotransport, pipeline conditioning and warm water extraction), and research in fine tailings, to demonstrate that although objectives may differ, government and industry research objectives are complementary

  11. Oil sands tailings leachability and toxicity evaluation

    International Nuclear Information System (INIS)

    Gulley, J.R.

    1995-01-01

    Fine tailings disposal and reclamation is a major issue facing the oil sands mining and extraction industry. Government regulations dictate that reclamation must return the site to a level of self-sustaining biological capability which approximates the natural condition. A two-phase laboratory program has been completed to investigate the suitability of alternative reclamation materials. For the first phase of the study, chemical and toxicological analyses were carried out on 13 different reclamation and reference materials (solid phase and extractions). Seedling emergence, nematode maturation, algal growth and bacterial luminescence for leachate samples showed a range of sensitivities in response to the tested materials, although phytotoxicity tests were generally the most sensitive. With the exception of one test material, high toxicity ratings were consistent with that expected from the chemical data. The second phase of the study focused on the evaluation of chemical and toxicological conditions in leachate water generated using bench-scale column percolation tests. Leachate water equivalent to 10 pore volume replacements was generated and temporal variations in toxicity and chemistry monitored. Similar to phase 1 findings, phytotoxicity tests were the most sensitive tests to leachate waters. For most materials tested, most toxicity was removed after 2--3 porewater replacements. More persistent toxicity was noted for samples containing bitumen (e.g., fine tails and oil sands). No clear correspondence was noted between chemical concentrations and toxicity in leachate waters

  12. Sulfur biogeochemistry of oil sands composite tailings

    Energy Technology Data Exchange (ETDEWEB)

    Warren, Lesley; Stephenson, Kate [Earth Sciences, McMaster University (Canada)], email: warrenl@mcmaster.ca; Penner, Tara [Syncrude Environmental Research (Canada)

    2011-07-01

    This paper discusses the sulfur biogeochemistry of oil sands composite tailings (CT). The Government of Alberta is accelerating reclamation activities on composite tailings. As a CT pilot reclamation operation, Syncrude is currently constructing the first freshwater fen. Minor unpredicted incidents with H2S gas released from the dewatering process associated with these reclamations have been reported. The objective of this study is to ascertain the connection between microbial activity and H2S generation within CT and to assess the sulfur biogeochemistry of untreated and treated (fen) CT over seasonal and annual timescales. The microbial geochemical interactions taking place are shown using a flow chart. CT is composed of gypsum, sand, clay and organics like naphthenic acids and bitumen. Sulfur and Fe cycling in mining systems and their microbial activities are presented. The chemistry and the processes involved within CT are also given along with the results. It can be said that the diverse Fe and S metabolizing microorganisms confirm the ecology involved in H2S dynamics.

  13. Low enthalpy geothermal for oil sands (LEGO)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    Geothermal energy is generated by the slow decay of radioactive materials within the Earth. Geothermal energy resources include the water from hot springs used for heating; the withdrawal of high temperature steam from deep wells; and the use of stable ground or water temperatures near the Earth's surface to heat or cool buildings or in industrial processes. Heat pumps are used to transfer heat or water from the ground into buildings in winter. This paper discussed low enthalpy geothermal options for oil sands processes in order to reduce the use of natural gas and emissions from greenhouse gases (GHGs). The study was also conducted to aid in the development of a portfolio of renewable energy options for the oil and gas sector. The study estimated the costs and benefits of operating a shallow geothermal borehole cluster for meeting a portion of process heat demands for the Nexen's Albian mine. The costs and benefits of operating thermo-chillers integrated with a shallow geothermal borehole cluster for waste heat mitigation were also evaluated. The study showed that geothermal designs can be used to meet a portion of oil sands process heat and cooling demands. Mining operators may reduce carbon emissions and energy costs for process heat demands by installing closed loop borehole heat exchangers. Geothermal heat storage capacity can also be used to increase the efficiency of thermal chillers. It was concluded that pilot plant studies would contribute to a better understanding of the technology. tabs., figs.

  14. Fire Stations, LAGIC is consulting with local parish GIS departments to create spatially accurate point and polygons data sets including the locations and building footprints of schools, churches, government buildings, law enforcement and emergency response offices, pha, Published in 2011, 1:12000 (1in=1000ft) scale, LSU Louisiana Geographic Information Center (LAGIC).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Fire Stations dataset current as of 2011. LAGIC is consulting with local parish GIS departments to create spatially accurate point and polygons data sets including...

  15. Grocery Stores, LAGIC is consulting with local parish GIS departments to create spatially accurate point and polygons data sets including the locations and building footprints of schools, churches, government buildings, law enforcement and emergency response offices, pha, Published in 2011, 1:12000 (1in=1000ft) scale, LSU Louisiana Geographic Information Center (LAGIC).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Grocery Stores dataset current as of 2011. LAGIC is consulting with local parish GIS departments to create spatially accurate point and polygons data sets including...

  16. Libraries, LAGIC is consulting with local parish GIS departments to create spatially accurate point and polygons data sets including the locations and building footprints of schools, churches, government buildings, law enforcement and emergency response offices, pha, Published in 2011, 1:12000 (1in=1000ft) scale, LSU Louisiana Geographic Information Center (LAGIC).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Libraries dataset current as of 2011. LAGIC is consulting with local parish GIS departments to create spatially accurate point and polygons data sets including the...

  17. Spiders in mountain habitats of the Giant Mountains

    Czech Academy of Sciences Publication Activity Database

    Růžička, Vlastimil; Vaněk, J.; Šmilauer, P.

    2012-01-01

    Roč. 43, č. 4 (2012), s. 341-347 ISSN 1067-4136 Institutional research plan: CEZ:AV0Z50070508 Keywords : Giant Mountains (Krkonoše, Karkonosze) * spider s * anemo-orographic systems Subject RIV: EH - Ecology, Behaviour Impact factor: 0.236, year: 2012 http://www.springerlink.com/content/0k5g721q1155r146/fulltext.pdf

  18. Potensi Pasir Lokal Tanjung Bintang Pada Aluminium Sand Casting Terhadap Porositas Produk Hasil Cor Aluminium

    OpenAIRE

    Hendronursito, Yusup; Prayanda, Yogi

    2016-01-01

    Green sand is one of the most important components in the process of metal casting. The sand in Indonesia region is varied level of subtlety, size of sand, and shape of sand. Green sand used in the process of metal casting is possible can affect the quality of casting product. This aims to determine the potential of Tanjung Bintang sand as green sand and the quality of the product in terms of porosity defects. The research was conducted by varying sand river from Tanjung Bintang and sand from...

  19. Experimental Study on Superfine Sand Concrete Mixed by Double Mixing Technology

    OpenAIRE

    yuqing zhao

    2013-01-01

    Traditional concept thought that medium sand and fine sand can be used to mix concrete, superfine sand can not used to mix concrete. This makes the source of superfine sand limited. With the shortage of medium sand and fine sand, it is imperative to exploit the resource of superfine sand. Superfine sand concrete is mixed by means of Double-doped Technology-ultra-fine fly ash and super plasticizer. Primary factor influencing superfine sand concrete strength is studied by orthogonal test, the o...

  20. SURVEY, NATCHITOCHES PARISH, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Survey data includes spatial datasets and data tables necessary to digitally represent data collected in the survey phase of the study. (Source: FEMA Guidelines and...

  1. BASEMAP, POINTE COUPEE PARISH

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — FEMA Framework Basemap datasets comprise six of the seven FGDC themes of geospatial data that are used by most GIS applications (Note: the seventh framework theme,...

  2. HYDRAULICS, BOSSIER PARISH, LOUISIANA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Recent developments in digital terrain and geospatial database management technology make it possible to protect this investment for existing and future projects to...

  3. TERRAIN, UNION PARISH, LOUSIANA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — Terrain data, as defined in FEMA Guidelines and Specifications, Appendix N: Data Capture Standards, describes the digital topographic data that was used to create...

  4. Properties of Desert Sand and CMAS Glass

    Science.gov (United States)

    Bansal, Narottam P.; Choi, Sung R.

    2014-01-01

    As-received desert sand from a Middle East country has been characterized for its phase composition and thermal stability. X-ray diffraction analysis showed the presence of quartz (SiO2), calcite (CaCO3), gypsum (CaSO4.2H2O), and NaAlSi3O8 phases in as-received desert sand and showed weight loss of approx. 35 percent due to decomposition of CaCO3 and CaSO4.2H2O when heated to 1400 C. A batch of as-received desert sand was melted into calcium magnesium aluminosilicate (CMAS) glass at approx. 1500 C. From inductively coupled plasma-atomic emission spectrometry, chemical composition of the CMAS glass was analyzed to be 27.8CaO-4MgO-5Al2O3-61.6SiO2-0.6Fe2O3-1K2O (mole percent). Various physical, thermal and mechanical properties of the glass have been evaluated. Bulk density of CMAS glass was 2.69 g/cc, Young's modulus 92 GPa, Shear modulus 36 GPa, Poisson's ratio 0.28, dilatometric glass transition temperature (T (sub g)) 706 C, softening point (T (sub d)) 764 C, Vickers microhardness 6.3 +/- 0.4 GPa, indentation fracture toughness 0.75 +/- 0.15 MPa.m (sup 1/2), and coefficient of thermal expansion (CTE) 9.8 x 10 (exp -6)/degC in the temperature range 25 to 700 C. Temperature dependence of viscosity has also been estimated from various reference points of the CMAS glass using the Vogel-Fulcher-Tamman (VFT) equation. The glass remained amorphous after heat treating at 850 C for 10 hr but crystallized into CaSiO3 and Ca-Mg-Al silicate phases at 900 C or higher temperatures. Crystallization kinetics of the CMAS glass has also been investigated by differential thermal analysis (DTA). Activation energies for the crystallization of two different phases in the glass were calculated to be 403 and 483 kJ/mol, respectively.

  5. Microbial activity at Yucca Mountain

    International Nuclear Information System (INIS)

    Horn, J.M.; Meike, A.

    1995-01-01

    The U.S. Department of Energy is engaged in a suitability study for a potential geological repository at Yucca Mountain, Nevada, for the containment and storage of commercially generated spent fuel and defense high-level nuclear waste. There is growing recognition of the role that biotic factors could play in this repository, either directly through microbially induced corrosion (MIC), or indirectly by altering the chemical environment or contributing to the transport of radionuclides. As a first step toward describing and predicting these processes, a workshop was held on April 10-12, 1995, in Lafayette, California. The immediate aims of the workshop were: (1) To identify microbially related processes relevant to the design of a radioactive waste repository under conditions similar to those at Yucca Mountain. (2) To determine parameters that are critical to the evaluation of a disturbed subterranean environment. (3) To define the most effective means of investigating the factors thus identified

  6. Microbial activity at Yucca Mountain

    Energy Technology Data Exchange (ETDEWEB)

    Horn, J.M.; Meike, A.

    1995-09-25

    The U.S. Department of Energy is engaged in a suitability study for a potential geological repository at Yucca Mountain, Nevada, for the containment and storage of commercially generated spent fuel and defense high-level nuclear waste. There is growing recognition of the role that biotic factors could play in this repository, either directly through microbially induced corrosion (MIC), or indirectly by altering the chemical environment or contributing to the transport of radionuclides. As a first step toward describing and predicting these processes, a workshop was held on April 10-12, 1995, in Lafayette, California. The immediate aims of the workshop were: (1) To identify microbially related processes relevant to the design of a radioactive waste repository under conditions similar to those at Yucca Mountain. (2) To determine parameters that are critical to the evaluation of a disturbed subterranean environment. (3) To define the most effective means of investigating the factors thus identified.

  7. Managing Rocky Mountain spotted fever.

    Science.gov (United States)

    Minniear, Timothy D; Buckingham, Steven C

    2009-11-01

    Rocky Mountain spotted fever is caused by the tick-borne bacterium Rickettsia rickettsii. Symptoms range from moderate illness to severe illness, including cardiovascular compromise, coma and death. The disease is prevalent in most of the USA, especially during warmer months. The trademark presentation is fever and rash with a history of tick bite, although tick exposure is unappreciated in over a third of cases. Other signature symptoms include headache and abdominal pain. The antibiotic therapy of choice for R. rickettsii infection is doxycycline. Preventive measures for Rocky Mountain spotted fever and other tick-borne diseases include: wearing long-sleeved, light colored clothing; checking for tick attachment and removing attached ticks promptly; applying topical insect repellent; and treating clothing with permethrin.

  8. The physiology of mountain biking.

    Science.gov (United States)

    Impellizzeri, Franco M; Marcora, Samuele M

    2007-01-01

    Mountain biking is a popular outdoor recreational activity and an Olympic sport. Cross-country circuit races have a winning time of approximately equal 120 minutes and are performed at an average heart rate close to 90% of the maximum, corresponding to 84% of maximum oxygen uptake (VO2max). More than 80% of race time is spent above the lactate threshold. This very high exercise intensity is related to the fast starting phase of the race; the several climbs, forcing off-road cyclists to expend most of their effort going against gravity; greater rolling resistance; and the isometric contractions of arm and leg muscles necessary for bike handling and stabilisation. Because of the high power output (up to 500W) required during steep climbing and at the start of the race, anaerobic energy metabolism is also likely to be a factor of off-road cycling and deserves further investigation. Mountain bikers' physiological characteristics indicate that aerobic power (VO2max >70 mL/kg/min) and the ability to sustain high work rates for prolonged periods of time are prerequisites for competing at a high level in off-road cycling events. The anthropometric characteristics of mountain bikers are similar to climbers and all-terrain road cyclists. Various parameters of aerobic fitness are correlated to cross-country performance, suggesting that these tests are valid for the physiological assessment of competitive mountain bikers, especially when normalised to body mass. Factors other than aerobic power and capacity might influence off-road cycling performance and require further investigation. These include off-road cycling economy, anaerobic power and capacity, technical ability and pre-exercise nutritional strategies.

  9. Stakeholder relations in the oil sands : managing uncertainty

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-05-15

    Alberta's oil sands are now at the crossroads of a series of significant and complex global issues that will require careful negotiation by all stakeholders involved in the oil sands industry. This paper discussed methods of managing uncertainty and risk related to the oil sands industry's agenda for the future. Oil sands developers must continue to secure permission from communities and other key stakeholders in order to develop oil sand projects. Stakeholder relations between oil sands operators, First Nations, and Metis Nation communities must ensure that respect is maintained while environmental impacts are minimized and long-term economic benefits are secured for all parties. Environmental non-governmental organizations (ENGOs) must ensure that oil sands resources are developed responsibly, and that environmental standards are maintained. Seven key shifts in stakeholder relations resulting from the recent economic crisis were identified. These included (1) withdrawal from the multi-stakeholder process, (2) increased focus on government to demonstrate policy leadership, (3) a stronger push from ENGOs to express environmental concerns, (4) global lobby and public relations efforts from ENGOs, (5) companies retreating to local community stakeholders, (6) more active demands from First Nations and Metis Nations groups, and (7) companies challenging ENGO campaigns. The study concluded by suggesting that government leadership is needed to clear policy and regulatory frameworks for Canada's oil sands.

  10. On Foundation Improvement By Sand Replacement | Abam | Global ...

    African Journals Online (AJOL)

    This paper describes a simple foundation improvement method involving the replacement of poor foundation bearing soils with sand and the resultant improvement in bearing capacity and the minimization of settlement at the site of a large storage tank. Minimum thickness of sand replacement for various foundation loads ...

  11. Modeling sheet-flow sand transport under progressive surface waves

    NARCIS (Netherlands)

    Kranenburg, Wouter

    2013-01-01

    In the near-shore zone, energetic sea waves generate sheet-flow sand transport. In present day coastal models, wave-induced sheet-flow sand transport rates are usually predicted with semi-empirical transport formulas, based on extensive research on this phenomenon in oscillatory flow tunnels.

  12. Fine sand in motion: the influence of interstitial air

    NARCIS (Netherlands)

    Homan, T.A.M.

    2013-01-01

    Sand is a granular material, and therefore it consists of individual grains arranged in a packing. The pores in-between the grains are usually filled with a fluid, in this case air. Now, is this interstitial air able to influence the behavior of the sand bed as a whole? When a ball impacts on fine,

  13. Geophysical mapping of the occurrence of shallow oil sands in ...

    African Journals Online (AJOL)

    Oil sands are known to be an alternate source of energy and of great economic value. To map the occurrence of shallow oil sand deposits in Idiopopo, Okitipupa area in Ondo state southwestern Nigeria, vertical electric sounding (VES) in 11 stations along 3 profiles were carried out using the Schlumberger configuration.

  14. Provenance of Coastal dune sands along Red Sea, Egypt

    Indian Academy of Sciences (India)

    26

    accumulation of sands behind vegetation or any other obstacles. ... The study areas Safaga (SF) and Quseir (QS) field dunes (Fig. 1) ..... coastal dune sands were deposited in a passive margin of a synrift .... Sed Petrol 63(6), 1110-1117.

  15. Sea Bed Sand Waves Studied To Help Pipeline Planners

    NARCIS (Netherlands)

    van der Mark, C.F.; de Koning, M.F.; Blom, Astrid; Hulscher, Suzanne J.M.H.; Stolk, A.

    2008-01-01

    The article cites a study that offers information on the variability of sand wave characteristics in the North Sea. The sand waves variability includes a statement that pipelines may start vibrating due to turbulence generated under the free span and navigational channels often need to be dredged

  16. Archaen to Recent aeolian sand systems and their sedimentary record

    DEFF Research Database (Denmark)

    Rodríguez-López, Juan Pedro; Clemmensen, Lars B; Lancaster, Nick

    2014-01-01

    The sedimentary record of aeolian sand systems extends from the Archean to the Quaternary, yet current understanding of aeolian sedimentary processes and product remains limited. Most preserved aeolian successions represent inland sand-sea or dunefield (erg) deposits, whereas coastal systems are ...

  17. Sand transport in urbanized beaches - models and reality

    International Nuclear Information System (INIS)

    Pineiro, G.; Norbis, W.; Panario, D.

    2012-01-01

    The general objective is to quantify the wind transport of sand in the urbanized beaches. The specific objectives include testing and calibration of the wind velocity as well as the classification of the beaches according to the magnitude and the direction of sand transport

  18. Test Setup for Axially Loaded Piles in Sand

    DEFF Research Database (Denmark)

    Thomassen, Kristina

    The test setup for testing axially static and cyclic loaded piles in sand is described in the following. The purpose for the tests is to examine the tensile capacity of axially loaded piles in dense fully saturated sand. The pile dimensions are chosen to resemble full scale dimension of piles used...... in offshore pile foundations today....

  19. Beach Sand Analysis for Indicators of Microbial Contamination

    Science.gov (United States)

    Traditional beach monitoring has focused on water quality, with little attention paid to health risks associated with beach sand. Recent research has reported that fecal indicator bacteria, as well as human pathogens can be found in beach sand and may constitute a risk to human h...

  20. Effect of Crushed Sandstone Sand on the Properties of High ...

    African Journals Online (AJOL)

    This paper presents results of the laboratory investigation on high performance concrete (HPC) using crushed sandstone sand as 20%, 40%, and 60% replacement of river sand together with superplastisizer and silica fume (SF). The fresh concrete properties such as slump, air content and fresh concrete density have been ...

  1. Sediment Source Fingerprinting of the Lake Urmia Sand Dunes.

    Science.gov (United States)

    Ahmady-Birgani, Hesam; Agahi, Edris; Ahmadi, Seyed Javad; Erfanian, Mahdi

    2018-01-09

    Aeolian sand dunes are continuously being discovered in inner dry lands and coastal areas, most of which have been formed over the Last Glacial Maximum. Presently, due to some natural and anthropogenic implications on earth, newly-born sand dunes are quickly emerging. Lake Urmia, the world's second largest permanent hypersaline lake, has started shrinking, vast lands comprising sand dunes over the western shore of the lake have appeared and one question has been playing on the minds of nearby dwellers: where are these sand dunes coming from, What there was not 15 years ago!! In the present study, the determination of the source of the Lake Urmia sand dunes in terms of the quantifying relative contribution of each upstream geomorphological/lithological unit has been performed using geochemical fingerprinting techniques. The findings demonstrate that the alluvial and the fluvial sediments of the western upstream catchment have been transported by water erosion and they accumulated in the lower reaches of the Kahriz River. Wind erosion, as a secondary agent, have carried the aeolian sand-sized sediments to the sand dune area. Hence, the Lake Urmia sand dunes have been originating from simultaneous and joint actions of alluvial, fluvial and aeolian processes.

  2. Effectiveness of SCADA Systems in Control of Green Sands Properties

    Directory of Open Access Journals (Sweden)

    Ignaszak Z.

    2016-03-01

    Full Text Available The paper undertakes an important topic of evaluation of effectiveness of SCADA (Supervisory Control and Data Acquisition systems, used for monitoring and control of selected processing parameters of classic green sands used in foundry. Main focus was put on process studies of properties of so-called 1st generation molding sands in the respect of their preparation process. Possible methods of control of this processing are presented, with consideration of application of fresh raw materials, return sand (regenerate and water. The studies conducted in one of European foundries were aimed at pointing out how much application of new, automated plant of sand processing incorporating the SCADA systems allows stabilizing results of measurement of selected sand parameters after its mixing. The studies concerned two comparative periods of time, before an implementation of the automated devices for green sands processing (ASMS - Automatic Sand Measurement System and MCM – Main Control Module and after the implementation. Results of measurement of selected sand properties after implementation of the ASMS were also evaluated and compared with testing studies conducted periodically in laboratory.

  3. Pathogen removal using saturated sand colums supplemented with hydrochar

    NARCIS (Netherlands)

    Chung, J.W.

    2015-01-01

    This PhD study has evaluated hydrochars derived from biowastes as adsorbents for pathogen removal in water treatment. Pathogen removal experiments were conducted by carrying out breakthrough analysis using a simple sand filtration set-up. Glass columns packed by 10 cm sand bed supplemented with

  4. Providing floating capabilities in latest-generation sand screens

    Energy Technology Data Exchange (ETDEWEB)

    Bowen, E.G.; Coronado, M.P. [Society of Petroleum Engineers, Richardson, TX (United States)]|[Baker Hughes, Houston, TX (United States)

    2008-10-15

    Alternative production methods are needed for the massive reserves located in the bitumen region of Canada's tar sands. The area has over 100 installations of sand screens/slotted liners in both injection and production legs using steam-assisted gravity drainage (SAGD) technology. Multiple wells must be drilled from a single pad because of the sensitive nature of the environment. With significant depths of these wells, a floating sand screen provides assurance that the sand screen will reach the desired depth. Paraffin is generally used to plug the flow access of the screen during installation. This paper discussed a new technology that has been developed to allow for sand screen installations without relying on paraffin wax to withstand differential pressure. The new technology uses a hydro-mechanical valving system incorporated into the screen design to temporarily close off the screen while being run in the hole. The paper described how the technology could provide a reliable, time-saving solution for SAGD installations when floating sand control screens are needed. The paper discussed current technology and its limitations, sand screen installation, screen design for floating applications, and additional applications. It was concluded that this technology solution provides a unique alternative to the methods currently used to install sand screens with SAGD technology in the fast growing Canadian market for bitumen recovery. 2 refs., 5 figs.

  5. Cavity prediction in sand mould production applying the DISAMATIC process

    DEFF Research Database (Denmark)

    Hovad, Emil; Larsen, Per; Spangenberg, Jon

    2017-01-01

    The sand shot in the DISAMATIC process is simulated by the discrete element method (DEM) taking into account the influence and coupling of the airflow with computational fluid dynamics (CFD). The DEM model is calibrated by a ring shear test, a sand pile experiment and a slump test. Subsequently...

  6. Ecosystem-based design rules for marine sand extraction sites

    NARCIS (Netherlands)

    Jong, de Maarten F.; Borsje, Bas W.; Baptist, Martin J.; Wal, van der Jan Tjalling; Lindeboom, Han J.; Hoekstra, Piet

    2016-01-01

    The demand for marine sand in the Netherlands as well as globally is increasing. Over the last decades, only shallow sand extraction of 2m below the seabed was allowed on the Dutch Continental Shelf (DCS). To guarantee sufficient supply and to decrease the surface area of direct impact, the Dutch

  7. Ecosystem-based design rules for marine sand extraction sites

    NARCIS (Netherlands)

    de Jong, Maarten F.; Borsje, Bas W.; Baptist, Martin J.; van der Wal, Jan Tjalling; Lindeboom, Han J.; Hoekstra, Piet

    2016-01-01

    The demand for marine sand in the Netherlands as well as globally is increasing. Over the last decades, only shallow sand extraction of 2m below the seabed was allowed on the Dutch Continental Shelf (DCS). To guarantee sufficient supply and to decrease the surface area of direct impact, the Dutch

  8. Sorption of europium by Haro river sand in aqueous solution

    International Nuclear Information System (INIS)

    Syed Moosa Hasany; Syed Javaid Khurshid

    1997-01-01

    The sorption of Eu(III) on Haro river sand has been investigated. Influences include composition of the sorptive medium, the concentration of sorbent and sorbate, and shaking time. Haro river sand can be exploited for the preconcentration and removal of europium from very dilute solutions, for the decontamination and treatment of radioactive waste water and effluents from nuclear installations. (Author)

  9. Effects of oil sands sediments on fish

    International Nuclear Information System (INIS)

    Parrott, J.; Colavecchia, M.; Hewitt, L.; Sherry, J.; Headley, J.; Turcotte, D.; Liber, K.

    2010-01-01

    This paper described a collaborative project organized by Natural Resources Canada (NRCan) Panel of Energy Research and Development (PERD) with researchers from Environment Canada and the University of Saskatchewan. The 4-year study was conducted to assess the toxicity of oil sands sediments and river waters, and reclamation ponds and sediments on laboratory-raised fish. Three sediments from rivers were evaluated for their potential to cause adverse impacts on fathead minnow eggs and larvae for a period of 18 days. The study monitored hatching, larval survival, development, and growth. Naphthenic acids (NA), polycyclic aromatic hydrocarbons (PAHs) and metals were measured in the sediments to determine if the compounds can be correlated with observed toxicity. The study will also assess walleye eggs exposed to sediments, and in situ fish exposures. Toxicity identification and evaluation (TIE) studies will be conducted to isolate the fractions that may affect fish development and growth.

  10. The state of oil sands wetland reclamation

    Energy Technology Data Exchange (ETDEWEB)

    Foote, L. [Alberta Univ., Edmonton, AB (Canada)

    2010-07-01

    The state of oil sand and wetlands reclamation was the subject of this presentation. Wildlife habitat and response, plant community and production, and microbial biology were examples of research areas surrounding this body of knowledge. Hydrological research and landscape ecology were discussed along with peatlands and marshes such as the Corvette and the Kia. A few examples of what has been learned in the area of wetlands reclamation was presented. Other topics were also discussed, such as timeframes, pragmatic policy approaches, reclamation costs, research needs and some ideas on maturing the field. It was concluded that environmental conditions change with time and area because of time, chemistry, physics, stoichiometry, as well as biotic mediation and facilitation. figs.

  11. Petro-Canada's oil sands supply outlook

    International Nuclear Information System (INIS)

    Sangster, B.

    2004-01-01

    A report by the Canadian Energy Research Institute suggests that by 2017, production from the Athabasca Oil Sands could reach as high as 3.5 million barrels per day (mbpd), or it could be as low as 1.1 mbpd. This uncertainty in production is due to several variables such as capital costs, project size, reservoir quality, pipeline capacity and workforce productivity. Other factors that influence production include marginal economics, markets and prices, investor confidence, stakeholder concerns and the Kyoto Protocol. The production level that will be achieved by 2017 will depend on how industry address these emerging issues. The author discussed these issues in detail with particular reference to the approach that Petro-Canada has taken to address the challenges. Suggestions to reduce the potential impacts of these challenges were also presented. tabs., figs

  12. Bison and the oil sands industry

    International Nuclear Information System (INIS)

    Pauls, R.W.

    1998-01-01

    Syncrude's Mildred Lake oil sands development project is located within the central boreal mixed wood forest in an area supporting traditional land uses, including trapping and harvesting of wildlife and plant materials by Fort McKay First Nation residents, in a community within 10 km of the Syncrude development. Reclamation requirements and standards in Alberta specify that the reclamation process must restore a landscape capability equivalent to, or better than that existing before disturbance. Syncrude is committed to complying with all provincial requirements and guidelines in all aspects of its business, including land reclamation. A five year research program has been established to determine the feasibility of reclaiming a portion of the landscape to support wood bison and bison subspecies once indigenous to this area. The current project may be expanded as a pilot commercial ranching venture to explore its commercial viability as a business venture by the Fort McKay First nations

  13. Direct Production of Silicones From Sand

    Energy Technology Data Exchange (ETDEWEB)

    Larry N. Lewis; F.J. Schattenmann: J.P. Lemmon

    2001-09-30

    Silicon, in the form of silica and silicates, is the second most abundant element in the earth's crust. However the synthesis of silicones (scheme 1) and almost all organosilicon chemistry is only accessible through elemental silicon. Silicon dioxide (sand or quartz) is converted to chemical-grade elemental silicon in an energy intensive reduction process, a result of the exceptional thermodynamic stability of silica. Then, the silicon is reacted with methyl chloride to give a mixture of methylchlorosilanes catalyzed by cooper containing a variety of tract metals such as tin, zinc etc. The so-called direct process was first discovered at GE in 1940. The methylchlorosilanes are distilled to purify and separate the major reaction components, the most important of which is dimethyldichlorosilane. Polymerization of dimethyldichlorosilane by controlled hydrolysis results in the formation of silicone polymers. Worldwide, the silicones industry produces about 1.3 billion pounds of the basic silicon polymer, polydimethylsiloxane.

  14. Mountain Plant Community Sentinels: AWOL

    Science.gov (United States)

    Malanson, G. P.

    2017-12-01

    Mountain plant communities are thought to be sensitive to climate change. Because climatic gradients are steep on mountain slopes, the spatial response of plant communities to climate change should be compressed and easier to detect. These expectations have led to identifying mountain plant communities as sentinels for climate change. This idea has, however, been criticized. Two critiques, for alpine treeline and alpine tundra, are rehearsed and supplemented. The critique of alpine treeline as sentinel is bolstered with new model results on the confounding role of dispersal mechanisms and sensitivity to climatic volatility. In alpine tundra, for which background turnover rates have yet to be established, community composition may reflect environmental gradients only for extremes where effects of climate are most indirect. Both plant communities, while primarily determined by energy at broad scales, may respond to water as a proximate driver at local scales. These plant communities may not be in equilibrium with climate, and differently scaled time lags may mean that ongoing vegetation change may not signal ongoing climate change (or lack thereof). In both cases a double-whammy is created by scale dependence for time lags and for drivers leading to confusion, but these cases present opportunities for insights into basic ecology.

  15. Recycling of petroleum-contaminated sand.

    Science.gov (United States)

    Taha, R; Ba-Omar, M; Pillay, A E; Roos, G; al-Hamdi, A

    2001-08-01

    The environmental impact of using petroleum-contaminated sand (PCS) as a substitute in asphalt paving mixtures was examined. An appreciable component of PCS is oily sludge, which is found as the dregs in oil storage tanks and is also produced as a result of oil spills on clean sand. The current method for the disposal of oily sludge is land farming. However, this method has not been successful as an oil content of reuse of the sludge in asphalt paving mixtures was therefore considered as an alternative. Standard tests and environmental studies were conducted to establish the integrity of the materials containing the recycled sludge. These included physical and chemical characterization of the sludge itself, and an assessment of the mechanical properties of materials containing 0%, 5%, 22% and 50% oily sludge. The blended mixtures were subjected to special tests, such as Marshall testing and the determination of stability and flow properties. The experimental results indicated that mixtures containing up to 22% oily sludge could meet the necessary criteria for a specific asphalt concrete wearing course or bituminous base course. To maximize the assay from the recycled material, the environmental assessment was restricted to the 50% oily sludge mixture. Leachates associated with this particular mixture were assayed for total organic residue and certain hazardous metal contaminants. The results revealed that the organics were negligible, and the concentrations of the metals were not significant. Thus, no adverse environmental impact should be anticipated from the use of the recycled product. Our research showed that the disposal of oily sludge in asphalt paving mixtures could possibly yield considerable savings per tonne of asphalt concrete, and concurrently minimize any direct impact on the environment.

  16. Improvement of composition of core sand and molding sand mixtures for power machine building castings

    International Nuclear Information System (INIS)

    Velikanov, G.F.; Primak, I.N.; Brechko, A.A.

    1982-01-01

    Considered is a problem of development and improvement of mixtures, as well as of antisticking coatings with the given parameters providing production of castings of the necessary quality. Requirements to properties of mixtures and antisticking coatings are formulated proceeding from the conditions of guaranteed production of qualitative steel castings with mass from 0.5 up to 20t and wall thickness from 60 up to 200 mm. Formation of film structure of binding compositions is studied, their marginal contact angle and surface tension are determined. In the result of work carried out on improvement of core sand and molding sand mixtures the labour productivity during the production of core and moldings has been increased in 20-25% in average, the quality has also been improved [ru

  17. Big picture thinking in oil sands tailings disposal

    Energy Technology Data Exchange (ETDEWEB)

    Boswell, J. [Thurber Engineering Ltd., Calgary, AB (Canada)

    2010-07-01

    This PowerPoint presentation discussed methods of disposing oil sands tailings. Oil sands operators are currently challenged by a variety of legislative and environmental factors concerning the creation and disposal of oil sands tailings. The media has focused on the negative ecological impact of oil sands production, and technical issues are reducing the effect of some mitigation processes. Operators must learn to manage the interface between tailings production and removal, the environment, and public opinion. The successful management of oil sand tailings will include procedures designed to improve reclamation processes, understand environmental laws and regulations, and ensure that the cumulative impacts of tailings are mitigated. Geotechnical investigations, engineering designs and various auditing procedures can be used to develop tailings management plans. Environmental screening and impact assessments can be used to develop sustainable solutions. Public participation and environmental mediation is needed to integrate the public, environmental and technical tailings management strategies. Operators must ensure public accountability for all stakeholders. tabs., figs.

  18. Compressive Strength of Compacted Clay-Sand Mixes

    Directory of Open Access Journals (Sweden)

    Faseel Suleman Khan

    2014-01-01

    Full Text Available The use of sand to improve the strength of natural clays provides a viable alternative for civil infrastructure construction involving earthwork. The main objective of this note was to investigate the compressive strength of compacted clay-sand mixes. A natural clay of high plasticity was mixed with 20% and 40% sand (SP and their compaction and strength properties were determined. Results indicated that the investigated materials exhibited a brittle behaviour on the dry side of optimum and a ductile behaviour on the wet side of optimum. For each material, the compressive strength increased with an increase in density following a power law function. Conversely, the compressive strength increased with decreasing water content of the material following a similar function. Finally, the compressive strength decreased with an increase in sand content because of increased material heterogeneity and loss of sand grains from the sides during shearing.

  19. Laboratory Test Setup for Cyclic Axially Loaded Piles in Sand

    DEFF Research Database (Denmark)

    Thomassen, Kristina; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

    2017-01-01

    This paper presents a comprehensive description and the considerations regarding the design of a new laboratory test setup for testing cyclic axially loaded piles in sand. The test setup aims at analysing the effect of axial one-way cyclic loading on pile capacity and accumulated displacements....... Another aim was to test a large diameter pile segment with dimensions resembling full-scale piles to model the interface properties between pile and sand correctly. The pile segment was an open-ended steel pipe pile with a diameter of 0.5 m and a length of 1 m. The sand conditions resembled the dense sand...... determined from the API RP 2GEO standard and from the test results indicated over consolidation of the sand. Two initial one-way cyclic loading tests provided results of effects on pile capacity and accumulated displacements in agreement with other researchers’ test results....

  20. Modelling the behavior of an oil saturated sand

    International Nuclear Information System (INIS)

    Evgin, E.; Altaee, A.; Lord, S.; Konuk, I.

    1990-01-01

    The experiments carried out in an earlier study show the oil contamination affects the strength and deformation characteristics of a crushed quartz sand. In the present study, a mathematical soil model is used to simulate the mechanical behavior of the same sand. The model parameters are determined for both clean and oil contaminated soil. Simulations are made for the stress-strain behavior of the soil in drained and undrained conventional traixial compression tests. In order to illustrate the effect of changes in the soil properties on the behavior of an engineering structure, a finite element analysis is carried out. In this paper comparative results are presented to show the differences in the behavior of a foundation resting on a clean sand, on an oil contaminated sand, and on a sand contaminated locally

  1. Sand impaction of the small intestine in eight dogs.

    Science.gov (United States)

    Moles, A D; McGhite, A; Schaaf, O R; Read, R

    2010-01-01

    To describe signalment, clinical findings, imaging and treatment of intestinal sand impaction in the dog. Medical records of dogs with radiographic evidence of small intestinal sand impaction were reviewed. Sand impaction resulting in small intestinal obstruction was diagnosed in eight dogs. All dogs presented with signs of vomiting. Other clinical signs included anorexia, lethargy and abdominal pain. Radiographs confirmed the presence of radio-opaque material consistent with sand causing distension of the terminal small intestine in all dogs. Four dogs were treated surgically for their impaction and four dogs were managed medically. Seven of the eight dogs survived. Both medical and surgical management of intestinal sand impaction in the dog can be effective and both afford a good prognosis for recovery.

  2. Aeolian sand transport and aeolian deposits on Venus: A review

    Science.gov (United States)

    Kreslavsly, Mikhail A.; Bondarenko, Nataliya V.

    2017-06-01

    We review the current state of knowledge about aeolian sand transport and aeolian bedforms on planet Venus. This knowledge is limited by lack of observational data. Among the four planetary bodies of the Solar System with sufficient atmospheres in contact with solid surfaces, Venus has the densest atmosphere; the conditions there are transitional between those for terrestrial subaerial and subaqueous transport. The dense atmosphere causes low saltation threshold and short characteristic saltation length, and short scale length of the incipient dunes. A few lines of evidence indicate that the typical wind speeds exceed the saltation threshold; therefore, sand transport would be pervasive, if sand capable of saltation is available. Sand production on Venus is probably much slower than on the Earth; the major terrestrial sand sinks are also absent, however, lithification of sand through sintering is expected to be effective under Venus' conditions. Active transport is not detectable with the data available. Aeolian bedforms (transverse dunes) resolved in the currently available radar images occupy a tiny area on the planet; however, indirect observations suggest that small-scale unresolved aeolian bedforms are ubiquitous. Aeolian transport is probably limited by sand lithification causing shortage of saltation-capable material. Large impact events likely cause regional short-term spikes in aeolian transport by supplying a large amount of sand-size particles, as well as disintegration and activation of older indurated sand deposits. The data available are insufficient to understand whether the global aeolian sand transport occurs or not. More robust knowledge about aeolian transport on Venus is essential for future scientific exploration of the planet, in particular, for implementation and interpretation of geochemical studies of surface materials. High-resolution orbital radar imaging with local to regional coverage and desirable interferometric capabilities is the

  3. Sand waves on an epicontinental shelf: Northern Bering Sea

    Science.gov (United States)

    Field, M.E.; Nelson, C.H.; Cacchione, D.A.; Drake, D.E.

    1981-01-01

    Sand waves and current ripples occupy the crests and flanks of a series of large linear sand ridges (20 km ?? 5 km ?? 10 m high) lying in an open-marine setting in the northern Bering Sea. The sand wave area, which lies west of Seward Peninsula and southeast of Bering Strait, is exposed to the strong continuous flow of coastal water northward toward Bering Strait. A hierarchy of three sizes of superimposed bedforms, all facing northward, was observed in successive cruises in 1976 and 1977. Large sand waves (height 2 m; spacing 200 m) have smaller sand waves (height 1 m; spacing 20 m) lying at a small oblique angle on their stoss slopes. The smaller sand waves in turn have linguoid ripples on their stoss slopes. Repeated studies of the sand wave fields were made both years with high-resolution seismic-reflection profiles, side-scan sonographs, underwater photographs, current-meter stations, vibracores, and suspended-sediment samplers. Comparison of seismic and side-scan data collected along profile lines run both years showed changes in sand wave shape that indicate significant bedload transport within the year. Gouge marks made in sediment by keels of floating ice also showed significantly different patterns each year, further documenting modification to the bottom by sediment transport. During calm sea conditions in 1977, underwater video and camera observations showed formation and active migration of linguoid and straight-crested current ripples. Current speeds 1 m above the bottom were between 20 and 30 cm/s. Maximum current velocities and sand wave migration apparently occur when strong southwesterly winds enhance the steady northerly flow of coastal water. Many cross-stratified sand bodies in the geologic record are interpreted as having formed in a tidal- or storm-dominated setting. This study provides an example of formation and migration of large bedforms by the interaction of storms with strong uniform coastal currents in an open-marine setting. ?? 1981.

  4. Oblique second-order sand transport pathways on an intertidal sand flat in a natural tidal inlet system

    DEFF Research Database (Denmark)

    Ernstsen, Verner Brandbyge; Lefebvre, Alice; Kroon, Aart

    2013-01-01

    tide, sand is transported along ESE-oriented pathways across the intertidal flat towards the inner tidal basin. During the late stages of ebb tide, sand is transported in drainage channels (WSWoriented) from the intertidal flat towards the inlet channel. During storm events with winds from SW, wave...

  5. Mountain Weather and Climate, Third Edition

    Science.gov (United States)

    Hastenrath, Stefan

    2009-05-01

    For colleagues with diverse interests in the atmosphere, glaciers, radiation, landforms, water resources, vegetation, human implications, and more, Mountain Weather and Climate can be a valuable source of guidance and literature references. The book is organized into seven chapters: 1, Mountains and their climatological study; 2,Geographical controls of mountain meteorological elements; 3, Circulation systems related to orography; 4, Climatic characteristics of mountains; 5, Regional case studies; 6, Mountain bioclimatology; and 7, Changes in mountain climates. These chapters are supported by l78 diagrams and photographs, 47 tables, and some 2000 literature references. The volume has an appendix of units and energy conversion factors and a subject index, but it lacks an author index.

  6. Inbreeding in Gredos mountain range (Spain): contribution of multiple consanguinity and intervalley variation.

    Science.gov (United States)

    Fuster, V; Jiménez, A M; Colantonio, S E

    2001-04-01

    The present paper examines consanguineous marriages occurring between 1874 and 1975 in three valleys (Tormes, Alberche, and Tiétar) in the Sierra de Gredos mountain range, Avila province, Spain. Information was obtained from parish registers of 42 localities, corresponding to a total of 41,696 weddings. Consanguineous marriages were defined as those up to the third degree of consanguinity (second cousins). From 1874 to 1975 the percentage of related mates was 4.45% and the inbreeding coefficient was 0.0011868 (for 1874 to 1917 corresponding figures up to the fourth degree were 16.44% and 0.00 19085, respectively). In order to ascertain the characteristics and evolution of mating patterns in Gredos, the contribution of each degree of kinship was analyzed as a whole and then for each valley separately. Regarding total consanguineous marriages in Gredos, there is a low frequency of uncle-niece matings (0.21%) and a first-second cousin mating ratio (C22/C33) of 0.23 (up to the third degree of consanguinity). Before 1918 multiple matings (i.e., those involving more than a single relationship) accounted for 19.16% of consanguineous marriages (up to the fourth degree). The observed frequencies of multiple consanguineous marriages was, on average, about twice that expected at random, and the proportion of such marriages to total inbreeding was 34.65%. The temporal change of the Gredos inbreeding pattern was characterized by a recent decrease; the highest inbreeding levels correspond to the period from 1915 to 1944. Finally, intervalley differences (maximum inbreeding coefficient in the Tormes, minimum in the Tiétar) are interpreted considering the geography, population size, and population mobility for each valley

  7. The Geodiversity in Drift Sand Landscapes of The Netherlands

    Science.gov (United States)

    van den Ancker, Hanneke; Jungerius, Pieter Dirk; Riksen, Michel

    2015-04-01

    The authors carried out detailed field studies of more than twelve drift sand landscapes in The Netherlands. The objective of these studies was to restore Natura-2000 values by restoring the wind activity. Active drift sands occur almost exclusively in The Netherlands, Natura 2000 habitat 2330 'Inland dunes with open Corynephorus and Agrostis grasslands', for which reason our country is largely responsible for this European landscape. Active drift sands had almost disappeared for two reasons: first, the stabilization of the drift sands by air pollution, mainly nitrogen, which stimulates the growth of algae and grasses that initiate soil formation, and second, by the growth of forests surrounding the sands, which decreases the wind force. The restoration studies revealed differences in the geodiversity between and within the drift sand areas. Whereas the drift sands on geological and soil maps show as almost homogenous areas, they have in fact highly variable geo-conditions of which examples will be given. These geodiversity aspects concern differences in geomorphological structure, origin, sediments and age of the drift sands. Differences in wind and water erosion, trampling and soil formation add to the geodiversity within the drift sand areas. Especially in the primary stages of succession the differences in geodiversity are relevant for the Natura-2000 values. We discerned three main types of active sands. Firstly, the impressive drift sands with large parabolic dune structures, often consisting of series of interlocking parabolic dunes. They developed from the northeast towards the southwest, against the direction of the dominant wind, and must have taken centuries to develop. Small parts of these systems are still active, other parts show different degrees of soil formation. Their origin is still unclear but probably dates from medieval times (Heidinga, 1985, Jungerius & Riksen, 2008). Second are the drift sand areas with irregular hills from 0.5 to about 2

  8. Influence of sand base preparation on properties of chromite moulding sands with sodium silicate hardened with selected methods

    Directory of Open Access Journals (Sweden)

    Stachowicz M.

    2017-03-01

    Full Text Available The paper presents a research on the relation between thermal preparation of chromite sand base of moulding sands containing sodium silicate, hardened with selected physical and chemical methods, and structure of the created bonding bridges. Test specimens were prepared of chromite sand - fresh or baked at 950°C for 10 or 24 hours - mixed with 0.5 wt.% of the selected non-modified inorganic binder and, after forming, were hardened with CO2 or liquid esters, dried traditionally or heated with microwaves at 2.45 GHz. It was shown on the grounds of SEM observations that the time of baking the base sand and the hardening method significantly affect structure of the bonding bridges and are correlated with mechanical properties of the moulding sands. It was found that hardening chromite-based moulding mixtures with physical methods is much more favourable than hardening with chemical methods, guaranteeing also more than ten times higher mechanical properties.

  9. Mineralogic maturity of modern sand along a high-energy tropical coast: Baixada de Jacarepaguá, Rio de Janeiro, Brazil

    Science.gov (United States)

    Savage, K. M.; de Cesero, P.; Potter, P. E.

    Quarts arenites overlying crystalline basement are fairly common in the geologic record. A modern analog is provided in coastal Brazil where a small tropical lowland is bordered by abrupt, Precambrian granitic and gneissic mountains of the Serra do Mar. Nine different sedimentary environments were sampled, 57 sands were studied petrographically, and 8 complete chemical analyses were made. Here, arkosic river sands pass seaward into well defined, quartz-rich, stranded beach ridges and pure quartz arenites of the modern beach and shelf. Strong inshore wave power combined with tropical weathering seem to be the principal factors for this change. Tropical weathering also converted surface samples of arkosic Pliocene fan deposits into residual quartz arenites. Implications for the paleotectonic and paleoclimatic interpretation of ancient sandstones are also discussed.

  10. Archeological Data Recovery at Site 16SJB29, Near Willow Bend, St. John The Baptist Parish, Louisiana with a Discussion of Regional Archeological Expectations and Priorities Along the Mississippi River

    Science.gov (United States)

    1989-04-01

    later Mendez who purchased the Solis plantation, grew the cane and produced the tafia to distill rum. It was Mendez’s sugar maker, chemist Antoine Morin...Baton Rouge. Goodwin, R. Christopher, Paul C. Armstrong, Eric C. Poplin, David Moore, and Carol J. Poplin 1987 New Orleans Looking Forward to Its Past...Jill-Karen Yakubik, Herschel A. Franks, and Carol J. Poplin 1987 Cultural Resources Surev of the White Castle Revetment Item, lberville Parish, Louisiana

  11. Evaluation of wettability of binders used in moulding sands

    Directory of Open Access Journals (Sweden)

    Hutera B.

    2007-01-01

    Full Text Available Binders used in moulding sand have the differential properties. One of the main parameters influencing on moulding sand properties is wettability of the sand grain by binding material. In the article some problems concerned with wettability evaluation have been presented and the importance of this parameter for quantity description of process occurring in system: binder- sand grain has been mentioned. The procedure of wetting angle measurement and operation of prototype apparatus for wettability investigation of different binders used in moulding sand have been described, as well as the results of wetting angle measurement for different binders at different conditions. The addition of little amount of proper diluent to binder results in the state of equilibrium reached almost immediately. Such addition can also reduce the value of equilibrium contact angle. The uniform distribution of binder on the surface of the sand grains and reducing of the required mixing time can be obtained. It has also a positive effect on the moulding sand strength.

  12. Presence of Campylobacter and Salmonella in sand from bathing beaches.

    Science.gov (United States)

    Bolton, F J; Surman, S B; Martin, K; Wareing, D R; Humphrey, T J

    1999-02-01

    The purpose of this study was to determine the presence of thermophilic Campylobacter spp. and Salmonella spp. in sand from non-EEC standard and EEC standard designated beaches in different locations in the UK and to assess if potentially pathogenic strains were present. Campylobacter spp. were detected in 82/182 (45%) of sand samples and Salmonella spp. in 10/182 (6%). Campylobacter spp. were isolated from 46/92 (50%) of samples from non-EEC standard beaches and 36/90 (40%) from EEC standard beaches. The prevalence of Campylobacter spp. was greater in wet sand from both types of beaches but, surprisingly, more than 30% of samples from dry sand also contained these organisms. The major pathogenic species C. jejuni and C. coli were more prevalent in sand from non-EEC standard beaches. In contrast, C. lari and urease positive thermophilic campylobacters, which are associated with seagulls and other migratory birds, were more prevalent in sand from EEC standard beaches. Campylobacter isolates were further characterized by biotyping and serotyping, which confirmed that strains known to be of types associated with human infections were frequently found in sand on bathing beaches.

  13. Casting Ductile Iron in Layer Moulds Made from Ecological Sands

    Directory of Open Access Journals (Sweden)

    M. Rączka

    2012-09-01

    Full Text Available The article contains the results of tests performed under the target project in Hardtop Foundry Charsznica.The objective of the tests and studies was to develop a technology of making high-quality ductile iron castings, combined witheffective means of environmental protection. The studies presented in this article related to castings weighing from 1 to 300 kg made from ductile iron of grades 400-15 and 500-7, using two-layer moulds, where the facing and core sand was the sand with an alkaline organic binder, while backing sand was the sand with an inorganic geopolymer binder.A simplified method of sand reclamation was applied with possible reuse of the reclaim as an addition to the backing sand. The castiron spheroidising treatment and inoculation were selected taking into account the specific conditions of Hardtop Foundry. A pilot batch of castings was made, testing the gating and feeding systems and using exothermic sleeves on risers. The study confirmed the validity of the adopted concept of making ductile iron castings in layer moulds, while maintaining the content of sand with an organic binder at a level of maximum 15%.

  14. Canada's oil sands : opportunities and challenges to 2015 : an update

    International Nuclear Information System (INIS)

    2006-06-01

    This report updated an energy market assessment compiled and published by the National Energy Board (NEB) in 2004. Major changes resulting from recent developments in the oil sands industry were presented. The report was compiled from a series of informal meetings and discussions with a cross-section of oil sands stakeholders. Influences on recent oil sands development and production growth included market development and pipelines; rising capital and labour costs; operating costs; environmental impact management; high crude oil prices; rising global energy demand; technology innovations; and a more stable investment climate. A comparison of key assumptions between the current analysis and the 2004 report was presented, along with estimates of operating and supply costs for various types of oil sands recovery methods. Potential markets for oil sands production were reviewed. Environmental and socio-economic impacts on the industry included the larger than anticipated water withdrawals from the Athabasca River for mining operations; and uncertainties over land reclamation methods. The industry has also been impacted by a limited supply of skilled workers in Alberta. It was observed that the potential for building cogeneration capacity has decreased since the 2004 report. It was concluded that the oil sands industry will continue to grow rapidly, but the rate of development will depend on the balance that is reached between the opposing forces that affect the oil sands. Natural gas costs, high oil prices, air emissions management issues and water usage will continue to be of concern. 6 tabs., 7 figs

  15. Oil sands economic impacts Canada : CERI report : backgrounder

    International Nuclear Information System (INIS)

    2005-09-01

    Oil sands production now accounts for 1 out of every 2 barrels of supply in Western Canada. It is anticipated that Alberta's oil sands sector will experience significant growth over the next few decades. This paper provided an outline of the challenges and economic impacts resulting from oil sands development in Canada. Alberta's oil sands reserves are estimated at 175 billion barrels that are deemed economically recoverable using current technology. At current production levels, reserves will sustain production of 2.5 million barrels per day for the next 200 years. A study by the Canadian Energy Research Institute (CERI) has forecast $100 billion in investment for the 2000-2020 period. Numerous companies hold leases and are planning new projects. A number of recent advances in oil sands technology are expected to further reduce costs as development matures. A royalty and tax regime that provides long-term fiscal certainty is a key factor that supports current oil sands growth forecasts. The CERI study has indicated that economic spinoffs from oil sands development relate to employment generated outside of Alberta, and that the largest percentage of government revenue accrues to the federal government. However, development may be constrained because the pace of growth in the sector may exceed underlying infrastructure related to roads, housing and municipal services. An adequate workforce of qualified trades and technical and professional people is also crucial. Several pipeline projects have been proposed to deliver oil sands crudes to new markets over the next decade. It was concluded that the billions of dollars invested in oil sands in Alberta will contribute to the economic prosperity of the entire country. 11 figs

  16. Potential building sand deposits in Songkhla province area

    Directory of Open Access Journals (Sweden)

    Kooptarnond, K.

    2002-10-01

    Full Text Available An investigation of potential building sand deposits in Songkhla province area subdivided them into four regions according to their accumulation in various alluvial plains, meanders throughout alluvial deposits and residual soils. Four selected deposits, were Rattaphum-Khuan Niang, U-Taphao river, Na Mom, and Chana-Thepha regions. Information obtained from these deposits revealed a good correlation between the geomorphological features as interpreted from aerial photographs and those identified from vertical electrical resistivity sounding results. Sand samples were analysed for their physical and chemical properties. Petrographic studies were also undertaken to characterize the composition types, texture and shapes. An overview of the sand properties was used them to be within the acceptable limits for building sand. However, relatively high organic impurities and soundness were found in sand from Khuan Niang and Na Mom deposits. The result indicated a potential reconnaissance mineral resource of about 46 square kilometres.A reserve evaluation for natural building sand was carried out by using Geographic Information System (GIS. Maps of the various parameters considered were constructed in digital database format with the aid of Arc/Info and ArcView software. Overlay mapping and buffer zone modules were performed to evaluate inferred resources of building sand. The key parameters of analysis included the distance from transportation, distance from streams, lithology and thickness of sand layers. The remaining inferred sand total was of about 386 million cubic metres or about 1,021 million metric tons was therefore estimated, of which 60 percent lies in the Rattaphum-Khuan Niang region and 40 percent in the other regions.

  17. OS X Mountain Lion bible

    CERN Document Server

    Gruman, Galen

    2012-01-01

    The complete guide to Mac OS X, fully updated for the newest release! The Mac's solid, powerful operating system and the exploding popularity of iOS devices are fueling a strong increase in market share for Apple. Previous editions of this book have sold more than 75,000 copies, and this new edition is fully updated with all the exciting features of OS X Mountain Lion, including Game Center, Messages, and Notifications. Written by industry expert Galen Gruman, it covers all the basics and then delves deep into professional and higher-end topics, making it the one book you need to succeed with

  18. Seaside, mountain and... wind turbines

    International Nuclear Information System (INIS)

    Gossement, A.

    2011-01-01

    Several courts have given a ruling considering that the law 'Montagne' (January 9., 1985) and the law 'Littoral' (January 3., 1986) are opposable to the building license of wind turbines. The law 'Littoral' imposes that any new construction in seaside areas has to be built in continuity of existing villages or hamlets. The law 'Montagne' imposes similar constraints to avoid the construction of isolated buildings in mountain areas but, contrary to the law 'Littoral', it allows some impairment for instance for the construction of certain public equipment. (A.C.)

  19. Yucca Mountain and The Environment

    International Nuclear Information System (INIS)

    NA

    2005-01-01

    The Yucca Mountain Project places a high priority on protecting the environment. To ensure compliance with all state and federal environmental laws and regulations, the Project established an Environmental Management System. Important elements of the Environmental Management System include the following: (1) monitoring air, water, and other natural resources; (2) protecting plant and animal species by minimizing land disturbance; (3) restoring vegetation and wildlife habitat in disturbed areas; (4) protecting cultural resources; (5) minimizing waste, preventing pollution, and promoting environmental awareness; and (6) managing of hazardous and non-hazardous waste. Reducing the impacts of Project activities on the environment will continue for the duration of the Project

  20. SANDIA MOUNTAIN WILDERNESS, NEW MEXICO.

    Science.gov (United States)

    Hedlund, D.C.; Kness, R.F.

    1984-01-01

    Geologic and mineral-resource investigations in the Sandia Mountains in New Mexico indicate that a small part of the area has a probable mineral-resource potential. Most of the mineral occurrences are small barite-fluorite veins that occur along faults on the eastern slope of the range. The barite veins in the Landsend area and in the Tunnel Spring area are classed as having a probable mineral-resource potential. Fluorite veins which occur at the La Luz mine contain silver-bearing galeana and the area near this mine is regarded as having a probable resource potential for silver. No energy resources were identified in this study.

  1. High Temperature Thermal Properties of Bentonite Foundry Sand

    Directory of Open Access Journals (Sweden)

    Krajewski P.K.

    2015-06-01

    Full Text Available The paper presents results of measuring thermal conductivity and heat capacity of bentonite foundry sand in temperature range ambient - 900­­°C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements of the mould temperature field during the solidification of the casting, the temperature relationships of the measured properties were evaluated. It was confirmed that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured casting.

  2. Differences and commonalities impregnation of dry and wet sand

    Directory of Open Access Journals (Sweden)

    Maujuda МUZAFFAROVA

    2014-09-01

    Full Text Available The article is devoted to research new methods of physic-chemical methods of preventing deflation to protect railways and highways from such phenomena as exogenous sand drifts. In particular, first studied the possibility of using binders in sand wet state. Results can significantly extend the scope of the method, and identified with particular impregnation maintaining stability requirements protective cover reduces both the concentration previously recommended binders, and their costs, thereby securing implementation in practice of shifting sands resource-saving technology.

  3. Oil sands: Strategies for future development - An overview

    International Nuclear Information System (INIS)

    Yildirim, E.

    1995-01-01

    The Alberta Chamber of Resources developed a Task Force in 1993 to promote oil sands development, and to identify and publicize the social and economic benefits of oil sands operations. Formation, mission of the National Task Force, impediments and opportunities for development were summarized. Attributes of oil sands, benefits of their development, impediments to development, strategic development and potential growth scenarios were discussed. Cooperation between government and industry was deemed essential. Recommendations included development of a bitumen pipeline network, provision of incentives to encourage development, encouragement of risk and reward sharing between bitumen producers and up graders, and diversification of products and by-products. 7 figs., 12 refs

  4. Used Furan Sand Reclamation in REGMAS Vibratory Unit

    Directory of Open Access Journals (Sweden)

    Dańko J.

    2015-09-01

    Full Text Available The paper, especially dealt with problems of reclamation of used furan sand, carried out in new, vibratory sand reclamation unit REGMAS developed by researches from AGH-University of Science and Technology, Faculty of Foundry Engineering in Cracow (Poland. Functional characteristics of reclamation unit as well as the results of reclamation of used sand with furfuryl resin are discussed in the paper. The quality of reclaim was tested by means of the LOI and pH value, dust content in the reclaim and at least by the the quality of the castings produced in moulds prepared with the use of reclaimed matrix.

  5. Strength Characteristics of Quarry Dust in Replacement of Sand

    Science.gov (United States)

    Shyam Prakash, K.; Hanumantha Rao, Ch, Dr

    2017-08-01

    The replacement of natural fine aggregate by using quarry dust leads to consumption of generated quarry dust, the requirement of land fill area can be reduced and solves the natural sand scarcity problem. The sand availability as a fine aggregate at low cost which needs the reason to search as a alternative material. Even it causes saddle to dump the crusher dust at one place which causes environmental pollution. The chemical analysis, specific gravity, sieve analysis and compressive strength is identified for various percentage and grades of concrete by replacement of sand with quarry dust.

  6. The Canadian oil sands--a sticky future

    Energy Technology Data Exchange (ETDEWEB)

    Cowtan, S A

    1977-01-01

    The oil sands have been known for 200 yr but only over the last decade have they been recognized as a potential major energy source for Canada. The study looks at the present GCOS plant, and briefly discusses Canada's future energy requirements and how she might fill those requirements from conventional and nonconventional sources, such as the Frontier areas, oil sands mining, oil sands in situ, and heavy oil. The economics and the future of these sources and the environment necessary for their development are analyzed.

  7. Controls on the abruptness of gravel-sand transitions

    Science.gov (United States)

    Venditti, J. G.; Church, M. A.; Lamb, M. P.; Domarad, N.; Rennie, C. D.

    2014-12-01

    As gravel-bedded rivers fine downstream, they characteristically exhibit an abrupt transition from gravel- to sand-bed. This is the only abrupt transition in grain-size that occurs in the fluvial system and has attracted considerable attention. A number of competing theories have been proposed to account for the abruptness of the transition, including base-level control, attrition of ~10mm gravel to produce sand, and sediment sorting processes. The prevailing theory for the emergence of abrupt transitions is size selective sorting of bimodal sediment wherein gravel deposits due to downstream declining shear stress, fining the bedload until a sand-bed emerges. We explored this hypothesis by examining grain-size, shear stress, gravel mobility and sand suspension thresholds through the gravel-sand transition (GST) of the Fraser River, British Columbia. The Fraser GST is an arrested gravel wedge with patches of gravel downstream of the wedge forming a diffuse extension. There is an abrupt change in bed slope through the transition that leads to an abrupt change in shear stress. The GST, bed-slope change and backwater caused by the ocean are all coincident spatially, which enhances the sharpness of the GST. Interestingly, the bimodal reach of the river occurs downstream of the GST and exhibits no downstream gradients in shear stress, suspended sediment flux, gravel mobility or sand suspension thresholds. This calls into question the prevailing theory for the emergence of an abrupt GST by size selective sorting. We provide evidence, both empirical and theoretical, that suggests the emergence of an abrupt GST is caused by rapid deposition of sand when fine gravel deposits. We argue that the emergence of gravel-sand transitions is a consequence of gravel-bedded rivers adopting a steeper slope than sand-bedded rivers. The abruptness arises because the bed slope required to convey the gravel load fixes the distal location of a terminal gravel wedge, and once the river has

  8. Protection of the Mountain Ridgelines Utilizing GIS

    Science.gov (United States)

    Lee, S.; Lee, M.

    2013-12-01

    Korean peninsula is characterized by numerous hills and mountains. The longest mountain ridgeline starting from Mt. Baekdusan to Mt. Jirisan is called Baekdudaegan which is similar to the continental divide or topographical watershed. In this study, GIS data, such as remotesensing images, national digital map, and watershed map, are used to analyze Korean mountain ridgelines structure and one Baekdudaegan data and nine Ridgelines are extracted. When extracted Baekdudaegan and other Ridgelines are overlaid on geologic maps, granite and gneiss are main components on the mountain ridgelines. The main mountain ridgelines are considered as the spiritual heritage overlapped in the land in Korea. As the environmental state is relatively better than those of other region in Korea, so many mountain ridgelines are legally protected by national legislation. The mountain ridgelines has hierarchical system; Baekdudaegan, Jeongmaek, Gimaek and Jimaek etc. according to their scale and total lengths of ridgelines. As only part of mountain ridgelines are currently protected by law or managed in environmental impact assessment (EIA) procedure, we think that most part of them should be under protection. Considering the environmental state of the ridgelines, we think that some protective measures should be set up nearby 1 km on both sides of them. If there goes a development plan or project near the main mountain ridgelines, topographical change index (TCI) and topographical scale index (TSI) etc. are to be applied in EIA. This study intends: firstly, to analyze the topological characteristics of the Korean mountain ridgelines using GIS, secondly, to analyze the geological characteristics of nearby mountain ridgelines, and lastly, to find a way to utilize the results on EIA.

  9. Alberta oil sands crudes : upgrading and marketing

    International Nuclear Information System (INIS)

    Ashar, M.

    2008-01-01

    Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs

  10. Pan Am tar sand bid revealed

    Energy Technology Data Exchange (ETDEWEB)

    Gray, E

    1968-12-16

    Muskeg Oil Co., wholly-owned subsidiary of Pan American Canada Oil Co. Ltd., hopes to expand its proposed initial 8,000 bpd in situ Athabasca tar sand production scheme to an ultimate rate of 60,000 bpd. The Muskeg recovery process involves an in situ combustion technique developed by Pan American and applied successfully in experimental work in the Athabasca area. The underground burning process develops heat in the formation, reduces crude bitumen viscosity, and displaces the bitumen to the producing wells. Core analyses have been used to determine bitumen in place, wherever possible. Values for uncored wells were based on logs, through development of an empirical relationship between formation resistivity measured by focused logging devices and bitumen content determined by core analysis. The proposed recovery process is a 10-acre well spacing with 9-spot configuration. The McMurray Formation will be fractured hydraulically and preheated by a combustion process. The bitumen will be recovered by a combustion displacement process utilizing air and water.

  11. Fragmentation modeling of a resin bonded sand

    Science.gov (United States)

    Hilth, William; Ryckelynck, David

    2017-06-01

    Cemented sands exhibit a complex mechanical behavior that can lead to sophisticated models, with numerous parameters without real physical meaning. However, using a rather simple generalized critical state bonded soil model has proven to be a relevant compromise between an easy calibration and good results. The constitutive model formulation considers a non-associated elasto-plastic formulation within the critical state framework. The calibration procedure, using standard laboratory tests, is complemented by the study of an uniaxial compression test observed by tomography. Using finite elements simulations, this test is simulated considering a non-homogeneous 3D media. The tomography of compression sample gives access to 3D displacement fields by using image correlation techniques. Unfortunately these fields have missing experimental data because of the low resolution of correlations for low displacement magnitudes. We propose a recovery method that reconstructs 3D full displacement fields and 2D boundary displacement fields. These fields are mandatory for the calibration of the constitutive parameters by using 3D finite element simulations. The proposed recovery technique is based on a singular value decomposition of available experimental data. This calibration protocol enables an accurate prediction of the fragmentation of the specimen.

  12. Alberta oil sands crudes : upgrading and marketing

    Energy Technology Data Exchange (ETDEWEB)

    Ashar, M. [Suncor Energy, Fort McMurray, AB (Canada)

    2008-05-15

    Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs.

  13. Characterization of oils sands thickened tailings

    Energy Technology Data Exchange (ETDEWEB)

    Scott, J.D.; Jeeravipoolvarn, S.; Donahue, R.; Ozum, B. [Alberta Univ., Edmonton, AB (Canada). Dept. of Civil and Environmental Engineering

    2008-07-01

    This presentation discussed the characterization of oils sands thickened tailings. The problem statement was defined as the fact that many laboratory procedures to characterize fine tailings do not take into account the extraction process, and instead use standardized laboratory tests. The purpose of this presentation was to demonstrate how different extraction processes affect the fine tailings geotechnical properties and water chemistry. Properties that were characterized included particle size analysis from hydrometer-sieve tests; per cent clay from methylene blue tests; per cent clay from mineralogy tests; Atterberg limits; water chemistry; and morphology by scanning electron microscopy. The presentation discussed the origin of fines (silt and clay) in tailings; where fine particles come from; tailings materials; mineralogy of tailings; the hydrometer-sieve test on fine tailings and thickened tailings; and the methylene blue test. It was concluded that the great majority of clay minerals in the tailings come from the clay-shale discontinuous seams and layers. For thickened tailings, the dispersed and non-dispersed hydrometer tests show considerable difference in the amount of clay size material. tabs., figs.

  14. Failures in sand in reduced gravity environments

    Science.gov (United States)

    Marshall, Jason P.; Hurley, Ryan C.; Arthur, Dan; Vlahinic, Ivan; Senatore, Carmine; Iagnemma, Karl; Trease, Brian; Andrade, José E.

    2018-04-01

    The strength of granular materials, specifically sand is important for understanding physical phenomena on other celestial bodies. However, relatively few experiments have been conducted to determine the dependence of strength properties on gravity. In this work, we experimentally investigated relative values of strength (the peak friction angle, the residual friction angle, the angle of repose, and the peak dilatancy angle) in Earth, Martian, Lunar, and near-zero gravity. The various angles were captured in a classical passive Earth pressure experiment conducted on board a reduced gravity flight and analyzed using digital image correlation. The data showed essentially no dependence of the peak friction angle on gravity, a decrease in the residual friction angle between Martian and Lunar gravity, no dependence of the angle of repose on gravity, and an increase in the dilation angle between Martian and Lunar gravity. Additionally, multiple flow surfaces were seen in near-zero gravity. These results highlight the importance of understanding strength and deformation mechanisms of granular materials at different levels of gravity.

  15. Family and family education model in parish press of Great Poland in 2 Polish Republic: „Tygodnik Parafji Zbąszynskiej” example

    Directory of Open Access Journals (Sweden)

    MIROSŁAW PIWOWARCZYK

    2017-10-01

    Full Text Available Local press played a significant role in 2nd Polish Republic both from the perspective if state administration, territorial autonomies, political parties and the expectations of wide social environments and local communities. It fulfilled the need of information on the social, political, educational, cultural and economical life of specific environments. It also worked as a tool in propaganda and political agitation, it familiarized ideologies of political parties and expressed views and idea of local communities. It played an important part in local economy life; it educated and actively took part in popularization of interests in regional issues.Local press was both: amirror of contemporary social relations, political and national divisions and the important agent in initiatives such as cultural events. It registered and pictured life of the town and its area citizens, gave pedagogical impact on the young generation by giving them patterns and forms of positive social actions, popularized specific ideologies, educational concepts, patterns of behavior, it created and influenced the local communities attitudes and actions. Its role was especially visible in Great Poland, where local press helped in creation of socio-cultural life in small towns and education. In the group of magazines that specifically influenced local communities cultural character and had an important educational impact we should (undoubtedly include the parish press. Parish magazines in many cases played a role of the local community press. Beside the information on the church and parish community problems they included a lot of news from the life of the town and its area; they constituted a chronicle of local community events and also propagated precise world-view and coherent with it concepts oft. It was a case in Zbąszyń, were was published. played a sagnificant educational role in its environment. It propagated a homogenus, stright forward perspective (concept of

  16. Appraisal of the tight sands potential of the Sand Wash and Great Divide Basins

    International Nuclear Information System (INIS)

    1993-08-01

    The volume of future tight gas reserve additions is difficult to estimate because of uncertainties in the characterization and extent of the resource and the performance and cost-effectiveness of stimulation and production technologies. Ongoing R ampersand D by industry and government aims to reduce the risks and costs of producing these tight resources, increase the certainty of knowledge of their geologic characteristics and extent, and increase the efficiency of production technologies. Some basins expected to contain large volumes of tight gas are being evaluated as to their potential contribution to domestic gas supplies. This report describes the results of one such appraisal. This analysis addresses the tight portions of the Eastern Greater Green River Basin (Sand Wash and Great Divide Subbasins in Northwestern Colorado and Southwestern Wyoming, respectively), with respect to estimated gas-in-place, technical recovery, and potential reserves. Geological data were compiled from public and proprietary sources. The study estimated gas-in-place in significant (greater than 10 feet net sand thickness) tight sand intervals for six distinct vertical and 21 areal units of analysis. These units of analysis represent tight gas potential outside current areas of development. For each unit of analysis, a ''typical'' well was modeled to represent the costs, recovery and economics of near-term drilling prospects in that unit. Technically recoverable gas was calculated using reservoir properties and assumptions about current formation evaluation and extraction technology performance. Basin-specific capital and operating costs were incorporated along with taxes, royalties and current regulations to estimate the minimum required wellhead gas price required to make the typical well in each of unit of analysis economic

  17. Mountaineers

    OpenAIRE

    Thomson, John, 1837-1921, photographer

    2003-01-01

    89 x 110 mm. Woodburytype. A half-length portrait of a seated man from the village of Prodromos. The portrait appears in Thomson's 'Through Cyprus with the camera, in the autumn of 1878' (vol.2, London: Sampson Low, Marston, Searle, and Rivington, 1879). It is annotated: 'The villagers are a robust race, as may be gathered from the two following photographs, the first of which represents one of the chief people of the place, a man who deserves to be rendered famous for the kind manner in w...

  18. Mountaineers

    OpenAIRE

    Thomson, John, 1837-1921, photographer

    2003-01-01

    84 x 107 mm. Woodburytype. A posed portrait of a man from Prodromos. The portrait appears in Thomson's 'Through Cyprus with the camera, in the autumn of 1878' (vol.2, London: Sampson Low, Marston, Searle, and Rivington, 1879). It is annotated: 'Another Highlander figures in the second plate - a tall, bony man of a most obligingly good-natured disposition. He, however, looked a bold, determined character, whose massive hands and muscular frame would stand him in good stead in carrying out ...

  19. Rocky Mountain Research Station: 2011 Annual Accomplishments

    Science.gov (United States)

    Rick Fletcher

    2011-01-01

    The Rocky Mountain Research Station is one of seven regional units that make up the USDA Forest Service Research and Development organization ­ the most extensive natural resources research organization in the world. We maintain 12 field laboratories throughout a 12-state territory encompassing the Great Basin, Southwest, Rocky Mountains, and parts of the Great Plains...

  20. Rocky Mountain Research Station: 2010 Research Accomplishments

    Science.gov (United States)

    Rick Fletcher

    2010-01-01

    The Rocky Mountain Research Station is one of seven regional units that make up the USDA Forest Service Research and Development organization ­ the most extensive natural resources research organization in the world. We maintain 12 field laboratories throughout a 12-state territory encompassing the Great Basin, Southwest, Rocky Mountains, and parts of the Great Plains...

  1. Impact of Hypoxia on Man on Mountaineering

    Directory of Open Access Journals (Sweden)

    A. N. Kislitsyn

    2006-01-01

    Full Text Available External respiratory function was studied in those engaged in mountaineering. A negative correlation was found between the intensity of exercise and the changes in vital capacity under mountainous conditions. Changes occurring in the levels of glucose and cholesterol were considered in tourists.

  2. Rocky Mountain spotted fever in children.

    Science.gov (United States)

    Woods, Charles R

    2013-04-01

    Rocky Mountain spotted fever is typically undifferentiated from many other infections in the first few days of illness. Treatment should not be delayed pending confirmation of infection when Rocky Mountain spotted fever is suspected. Doxycycline is the drug of choice even for infants and children less than 8 years old. Copyright © 2013 Elsevier Inc. All rights reserved.

  3. Rocky Mountain Spotted Fever: Statistics and Epidemiology

    Science.gov (United States)

    ... Search Form Controls Cancel Submit Search the CDC Rocky Mountain Spotted Fever (RMSF) Note: Javascript is disabled or is not ... message, please visit this page: About CDC.gov . Rocky Mountain Spotted Fever (RMSF) Transmission Signs and Symptoms Diagnosis and Testing ...

  4. 78 FR 29366 - Green Mountain Power Corporation

    Science.gov (United States)

    2013-05-20

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. TS04-277-002] Green Mountain Power Corporation Notice of Filing Take notice that on May 2, 2013, Green Mountain Power Corporation filed additional information in support of its request for continued waiver of Standards of Conduct. Any...

  5. Extremely low long-term erosion rates around the Gamburtsev Mountains in interior East Antarctica

    Science.gov (United States)

    Cox, S. E.; Thomson, S. N.; Reiners, P. W.; Hemming, S. R.; van de Flierdt, T.

    2010-11-01

    The high elevation and rugged relief (>3 km) of the Gamburtsev Subglacial Mountains (GSM) have long been considered enigmatic. Orogenesis normally occurs near plate boundaries, not cratonic interiors, and large-scale tectonic activity last occurred in East Antarctica during the Pan-African (480-600 Ma). We sampled detrital apatite from Eocene sands in Prydz Bay at the terminus of the Lambert Graben, which drained a large pre-glacial basin including the northern Gamburtsev Mountains. Apatite fission-track and (U-Th)/He cooling ages constrain bedrock erosion rates throughout the catchment. We double-dated apatites to resolve individual cooling histories. Erosion was very slow, averaging 0.01-0.02 km/Myr for >250 Myr, supporting the preservation of high elevation in interior East Antarctica since at least the cessation of Permian rifting. Long-term topographic preservation lends credence to postulated high-elevation mountain ice caps in East Antarctica since at least the Cretaceous and to the idea that cold-based glaciation can preserve tectonically inactive topography.

  6. Reef community structure, Sand Island, Oahu HI, (NODC Accession 0000177)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — These reports provide the results of nine years (1990-98) of an annual quantitative monitoring of shallow marine communities inshore of the Sand Island Ocean...

  7. Effect of River Indus Sand on Concrete Tensile Strength

    Directory of Open Access Journals (Sweden)

    M. T. Lakhiar

    2018-04-01

    Full Text Available In the development of Pakistan construction industry, the utilization of River Indus sand in concrete as fine aggregate has expanded tremendously. The aim of this research is to study the effect of Indus River sand on the tensile strength of various grades of concrete when it is utilized as fine aggregate. Concrete Samples of M15, M20 and M25 grade concrete were cured for 7, 14, 21 and 28 days. Based on the results, it is found that concrete became less workable when Indus river sand was utilized. It is recorded that tensile strength of concrete is decreased from 5% up to 20% in comparison with hill sand. The results were derived from various concrete grades.

  8. Removal method of radium in mine water by filter sand

    International Nuclear Information System (INIS)

    Taki, Tomihiro; Naganuma, Masaki

    2003-01-01

    Trace radium is contained in mine water from the old mine road in Ningyo-Toge Environmental Engineering Center, JNC. We observed that filter sand with hydrated manganese oxide adsorbed radium in the mine water safely for long time. The removal method of radium by filter sand cladding with hydrated manganese oxide was studied. The results showed that radium was removed continuously and last for a long time from mine water with sodium hypochlorite solution by passing through the filter sand cladding with hydrated manganese. Only sodium hypochlorite solution was used. When excess of it was added, residue chlorine was used as chlorine disinfection. Filter sand cladding with hydrated manganese on the market can remove radium in the mine water. The removal efficiency of radium is the same as the radium coprecipitation method added with barium chloride. The cost is much lower than the ordinary methods. Amount of waste decreased to about 1/20 of the coprecipitation method. (S.Y.)

  9. Documenting the global impacts of beach sand mining

    Science.gov (United States)

    Young, R.; Griffith, A.

    2009-04-01

    For centuries, beach sand has been mined for use as aggregate in concrete, for heavy minerals, and for construction fill. The global extent and impact of this phenomenon has gone relatively unnoticed by academics, NGOs, and major news sources. Most reports of sand mining activities are found at the very local scale (if the mining is ever documented at all). Yet, sand mining in many localities has resulted in the complete destruction of beach (and related) ecosystems along with severe impacts to coastal protection and tourism. The Program for the Study of Developed Shorelines at Western Carolina University and Beachcare.org have initiated the construction of a global database of beach sand mining activities. The database is being built through a combination of site visits and through the data mining of media resources, peer reviewed papers, and reports from private and governmental entities. Currently, we have documented sand mining in 35 countries on 6 continents representing the removal of millions of cubic meters of sand. Problems extend from Asia where critical infrastructure has been disrupted by sand mining to the Caribbean where policy reform has swiftly followed a highly publicized theft of sand. The Program for the Study of Developed Shorelines recently observed extensive sand mining in Morocco at the regional scale. Tens of kilometers of beach have been stripped of sand and the mining continues southward reducing hope of a thriving tourism-based economy. Problems caused by beach sand mining include: destruction of natural beaches and the ecosystems they protect (e.g. dunes, wetlands), habitat loss for globally important species (e.g. turtles, shorebirds), destruction of nearshore marine ecosystems, increased shoreline erosion rates, reduced protection from storms, tsunamis, and wave events, and economic losses through tourist abandonment and loss of coastal aesthetics. The threats posed by sand mining are made even more critical given the prospect of a

  10. Chromian spinel-rich black sands from eastern shoreline of ...

    Indian Academy of Sciences (India)

    Chromian spinel; detrital sand; ophiolites; Andaman Island; India. J. Earth Syst. .... (olivine: ol) inclusion; (e) peridotitic spinel with extensive fracturing; and (f) heavily altered rim of a peridotitic spinel. ..... The authors acknowledge the financial.

  11. Consolidation of the formation sand by chemical methods

    Directory of Open Access Journals (Sweden)

    Mariana Mihočová

    2006-10-01

    Full Text Available The sand control by consolidation involves the process of injecting chemicals into the naturally unconsolidated formation to provide an in situ grain-to-grain cementation. The sand consolidation chemicals are available for some 30 years. Several types of consolidating material were tried. Presently available systems utilize solidified plastics to provide the cementation. These systems include phenol resin, phenol-formaldehyde, epoxy, furan and phenolic-furfuryl.The sand consolidation with the steam injection is a novel technique. This process provides a highly alkaline liquid phase and temperatures to 300 °C to geochemically create cements by interacting with the dirty sand.While the formation consolidation has widely applied, our experience has proved a high level of success.

  12. Santa Barbara Littoral Cell CRSMP Offshore Sand Sources 2009

    Data.gov (United States)

    California Natural Resource Agency — Offshore sand sources exist at four known locations and potentially other yet to be explored regions within the nearshore coastal shelf. Significant reserves of fine...

  13. Santa Barbara Littoral Cell CRSMP Offshore Sand Sources 2009

    Data.gov (United States)

    California Department of Resources — Offshore sand sources exist at four known locations and potentially other yet to be explored regions within the nearshore coastal shelf. Significant reserves of fine...

  14. The oil sands: A new energy vision for Canada

    International Nuclear Information System (INIS)

    1995-01-01

    Canada's oil sands deposits were considered to offer huge potential for wealth generation and enduring social benefits. This report showed that putting in action the plan developed by the National Task Force on Oil Sands Strategies would help unlock this potential and realize the benefits; the forecast called for a doubling or tripling of oil sands production over the next 25 years. The plan should also predicted an increase in investments in oil sands since the fiscal regime would be stable and the product would be in increasing demand. New capital investment should generate significant environmental, social and economic benefits. The real outcome would be increased national prosperity, since further growth in investment would translate into thousands of skilled jobs across Canada, expansion of government revenues, and improvements to Canada's trade balance. 1 ill

  15. The oil sands: A new energy vision for Canada

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    Canada`s oil sands deposits were considered to offer huge potential for wealth generation and enduring social benefits. This report showed that putting in action the plan developed by the National Task Force on Oil Sands Strategies would help unlock this potential and realize the benefits; the forecast called for a doubling or tripling of oil sands production over the next 25 years. The plan should also predicted an increase in investments in oil sands since the fiscal regime would be stable and the product would be in increasing demand. New capital investment should generate significant environmental, social and economic benefits. The real outcome would be increased national prosperity, since further growth in investment would translate into thousands of skilled jobs across Canada, expansion of government revenues, and improvements to Canada`s trade balance. 1 ill.

  16. Aging effects on oil-contaminated Kuwaiti sand

    International Nuclear Information System (INIS)

    Al-Sanad, H.A.; Ismael, N.F.

    1997-01-01

    Large quantities of oil-contaminated sands resulted from the destruction of oil wells and the formation of oil lakes in Kuwait at the end of the Gulf Wa/r. A laboratory testing program was carried out to determine the geotechnical properties of this material and the effect of aging on their properties. Tests included direct shear, triaxial, and consolidation tests on clean and contaminated sand at the same relative density. The influence of aging was examined by testing uncontaminated sand after aging for one, three, and six months in natural environmental conditions. The results indicated increased strength and stiffness due to aging and a reduction of the oil content due to evaporation of volatile compounds. The factors that influence the depth of oil penetration in compacted sand columns were also examined including the type of oil, relative density, and the amount of fines

  17. Evaluation of an Intergrated / Biocoagulant-sand filter Drum for ...

    African Journals Online (AJOL)

    User

    2015-03-18

    Mar 18, 2015 ... to adopt simple sand filtration for water treatment is exigent. ... Moringa oleifera, a vegetable plant found across Africa have been noted ... leachate samples from waste dumps within the city of Bamenda .... Total solids mg/dm3.

  18. Sand Point, Alaska Tsunami Forecast Grids for MOST Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Sand Point, Alaska Forecast Model Grids provides bathymetric data strictly for tsunami inundation modeling with the Method of Splitting Tsunami (MOST) model....

  19. Augmenting Sand Simulation Environments through Subdivision and Particle Refinement

    Science.gov (United States)

    Clothier, M.; Bailey, M.

    2012-12-01

    Recent advances in computer graphics and parallel processing hardware have provided disciplines with new methods to evaluate and visualize data. These advances have proven useful for earth and planetary scientists as many researchers are using this hardware to process large amounts of data for analysis. As such, this has provided opportunities for collaboration between computer graphics and the earth sciences. Through collaboration with the Oregon Space Grant and IGERT Ecosystem Informatics programs, we are investigating techniques for simulating the behavior of sand. We are also collaborating with the Jet Propulsion Laboratory's (JPL) DARTS Lab to exchange ideas and gain feedback on our research. The DARTS Lab specializes in simulation of planetary vehicles, such as the Mars rovers. Their simulations utilize a virtual "sand box" to test how a planetary vehicle responds to different environments. Our research builds upon this idea to create a sand simulation framework so that planetary environments, such as the harsh, sandy regions on Mars, are more fully realized. More specifically, we are focusing our research on the interaction between a planetary vehicle, such as a rover, and the sand beneath it, providing further insight into its performance. Unfortunately, this can be a computationally complex problem, especially if trying to represent the enormous quantities of sand particles interacting with each other. However, through the use of high-performance computing, we have developed a technique to subdivide areas of actively participating sand regions across a large landscape. Similar to a Level of Detail (LOD) technique, we only subdivide regions of a landscape where sand particles are actively participating with another object. While the sand is within this subdivision window and moves closer to the surface of the interacting object, the sand region subdivides into smaller regions until individual sand particles are left at the surface. As an example, let's say

  20. Selected Hydrologic Data for Sand Cove Wash, Washington County, Utah

    National Research Council Canada - National Science Library

    Norton, Aaron; Susong, David D

    2004-01-01

    .... Hydrologic data collected in this study are described and listed in this report. Six boreholes were drilled in Sand Cove Wash to determine the vertical and spatial distribution of the alluvial deposits and their hydrologic...

  1. Design of Screens for Sand Control of Wells

    Directory of Open Access Journals (Sweden)

    Ján Pinka

    2006-04-01

    Full Text Available Drilling, completion, production, and reservoir engineers, supervisors, foremen, superintendents, service company personnel, technologists and anyone involved with recommending, selecting, designing or on-site performance of well completions or workovers where sand production is, or may become, a serious problem will benefit from this course. Less sand influx can be expected in a horizontal well than in a vertical well. If horizontal holes in weak formation sands can be successfully gravel packed, the result could be significantly higher well productivity than with a liner, screen or pre-packed screen alone. The article covers innovative screens for sand control used in oil and gas industry from the world leaders in total completion. The type of screen (wire wrapped, reinforced, pre-packed, ect. should also be chosen with due consideration to running-in condition (curve radius, compression when the screens are pushed along the drain hole, etc..

  2. DEGRADATION AND MIGRATION OF VINCLOZOLIN IN SAND AND SOIL

    Science.gov (United States)

    The migration of the dicarboximide fungicide vinclozolin and its principal degradation products through porous media was experimentally determined by simulating pesticide applications to a 23-30 mesh Ottawa sand and a North Carolina Piedmont, aquic hapludult soil in laboratory ...

  3. Production of oil from Intermountain West tar sands deposits

    Energy Technology Data Exchange (ETDEWEB)

    Glassett, J.M.; Glassett, J.A.

    1976-03-01

    Six tar sand deposits in the Intermountain West, each containing more than one billion barrels of oil in place, are identified. All of these deposits are in eastern Utah and contain a total of twenty-eight billion barrels of oil. The names of the six deposits arranged in descending order of desirability for large-scale surface-mining oil recovery operations are as follows: Sunnyside, Tar Sand Triangle, Asphalt Ridge, P.R. Spring, Circle Cliffs, and Hill Creek. An overview of each deposit is presented including geology, surface-mining variables, chemical processing variables, environmental aspects, and economics. A comparison of Utah tar sands and Athabasca, Alberta, Canada tar sands is also presented.

  4. Characterizing volumetric deformation behavior of naturally occuring bituminous sand materials

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2009-05-01

    Full Text Available newly proposed hydrostatic compression test procedure. The test procedure applies field loading conditions of off-road construction and mining equipment to closely simulate the volumetric deformation and stiffness behaviour of oil sand materials. Based...

  5. Geochemistry of dark coastal heavy-mineral beaches sand (Annaba ...

    African Journals Online (AJOL)

    Acer

    3 Institute of Earth and Environmental Science, University of Potsdam, ... Some beaches are characterized by a red-brownish sand colour, the Ain Achir and the ... The occurrence of clays has been determined using the methyl-blue method.

  6. Half a Century of Life Don Khutor: the Parish Chronicle of St. Panteleimon• s Church of Khutor Letovskiy, Stanitsa Kremenskaia, Ust`-Medveditskaya District, Troops of the Don Region (1873-1929

    Directory of Open Access Journals (Sweden)

    Ageev Evgenii, priest

    2016-12-01

    Full Text Available The article puts forward into scientific circulation a valuable source on the history of the parish life of the late 19th — early 20th century on the Don — the parish chronicle found in one of the investigations of the repressed clergy. This chronicle is unique high temporal coverage, from 1873 to 1929, it includes the years of revolution, Civil war on the Don and the first post-revolutionary decade. The author gives a brief overview of the history of the chronicle, the characteristics of its six authors — rural priests. The first thirty years were marked by the construction and decoration of the church and the absence of conflict. The early twentieth century was marked by the confl icts of the parishioners with the clergy. In the chronicle it was described the hardships of the lives of ordinary Cossacks, the scourge of Civil war, the famine of the early 1920s. In the postwar years there has been growing discontent of the parishioners by the activities of the Soviet government: tax policy, anti-religious propaganda and oppression of the clergy, beginning with collectivization. Narratives are rural priests, and it refl ects their own perception of the key events of the age. The author in the article examines the attitude of the parishioners to the Church, their perception of current events, participation in parish life. He concludes on a high degree of involvement of Cossacks in the Church life, the importance of the Church in their daily lives. The facts given in the article, suggest the sustainability of the parish farm, the community was able to survive in the turmoil of the Civil war. Forced destruction of parish life in the years of collectivization destroyed the community and has led to the degradation and disappearance of rural settlement. The last author of the chronicle was repressed, he and those arrested with him the clergy and parishioners were accused of preparing an armed uprising. The chronicle shows that this

  7. Marine pollution: Let us not forget beach sand

    OpenAIRE

    Galgani, Francois; Ellerbrake, Katrin; Fries, Elke; Goreux, Chantal

    2011-01-01

    Background: Assessing the chemical or bacterial contamination in marine waters and sediments is a very common approach to evaluate marine pollution and associated risks. However, toxicity and organic pollution of beach sands have not yet been considered, except in adjacent waters. In the present study, the toxicity and the chemical contamination of natural beach sands collected 20 m from the shoreline at two sites located on the Mediterranean Sea (Marseille and La Marana, Corsica) were studie...

  8. Unconfined Groundwater Dispersion Model On Sand Layers In Coral Island

    OpenAIRE

    Sultan

    2016-01-01

    The research objective is to analyze the sand layer to determine the characteristics of the unconfined groundwater aquifer on coral island and found the dispersion model of unconfined groundwater in the sand layer in the coral island. The method used is direct research in the field, laboratory analysis and secondary data. Observations geological conditions, as well as the measurement and interpretation of geoelectrical potential groundwater models based on the value of the conductivity of gro...

  9. Western tight gas sands advanced logging workshop proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Jennings, J B; Carroll, Jr, H B [eds.

    1982-04-01

    An advanced logging research program is one major aspect of the Western Tight Sands Program. Purpose of this workshop is to help BETC define critical logging needs for tight gas sands and to allow free interchange of ideas on all aspects of the current logging research program. Sixteen papers and abstracts are included together with discussions. Separate abstracts have been prepared for the 12 papers. (DLC)

  10. Creating and maintaining a gas cap in tar sands formations

    Science.gov (United States)

    Vinegar, Harold J.; Karanikas, John Michael; Dinkoruk, Deniz Sumnu; Wellington, Scott Lee

    2010-03-16

    Methods for treating a tar sands formation are disclosed herein. Methods for treating a tar sands formation may include providing heat to at least part of a hydrocarbon layer in the formation from one or more heaters located in the formation. Pressure may be allowed to increase in an upper portion of the formation to provide a gas cap in the upper portion. At least some hydrocarbons are produced from a lower portion of the formation.

  11. Noise Exposure and Hearing Loss Among Sand and Gravel Miners

    OpenAIRE

    Landen, Deborah; Wilkins, Steve; Stephenson, Mark; McWilliams, Linda

    2004-01-01

    The objectives of this study were to describe workplace noise exposures, risk factors for hearing loss, and hearing levels among sand and gravel miners, and to determine whether full shift noise exposures resulted in changes in hearing thresholds from baseline values. Sand and gravel miners (n = 317) were interviewed regarding medical history, leisure-time and occupational noise exposure, other occupational exposures, and use of hearing protection. Audiometric tests were performed both before...

  12. MECHANISM OF PARTICLE SUSPENSION OVER A SAND WAVE

    OpenAIRE

    芦田, 和男; 藤田, 正治; 向井, 健

    1986-01-01

    The characteristics of flow vary with space over sand waves. It is important to consider thisnouniformity in the modeling of motions of suspended particles, but few methods for calculationof suspended load have been proposed by consideration of this efects. In this paper mean velocityand turbulent strength of flow are discussed experimentally over a two-dimensinal sand wave andthe motion of suspended particle are formulated using these results and authors' theory on modelof particle motion ov...

  13. Frac Sand Mines Are Preferentially Sited in Unzoned Rural Areas.

    Directory of Open Access Journals (Sweden)

    Christina Locke

    Full Text Available Shifting markets can cause unexpected, stochastic changes in rural landscapes that may take local communities by surprise. Preferential siting of new industrial facilities in poor areas or in areas with few regulatory restrictions can have implications for environmental sustainability, human health, and social justice. This study focuses on frac sand mining-the mining of high-quality silica sand used in hydraulic fracturing processes for gas and oil extraction. Frac sand mining gained prominence in the 2000s in the upper midwestern United States where nonmetallic mining is regulated primarily by local zoning. I asked whether frac sand mines were more commonly sited in rural townships without formal zoning regulations or planning processes than in those that undertook zoning and planning before the frac sand boom. I also asked if mine prevalence was correlated with socioeconomic differences across townships. After creating a probability surface to map areas most suitable for frac sand mine occurrence, I developed neutral landscape models from which to compare actual mine distributions in zoned and unzoned areas at three different spatial extents. Mines were significantly clustered in unzoned jurisdictions at the statewide level and in 7 of the 8 counties with at least three frac sand mines and some unzoned land. Subsequent regression analyses showed mine prevalence to be uncorrelated with land value, tax rate, or per capita income, but correlated with remoteness and zoning. The predicted mine count in unzoned townships was over two times higher than that in zoned townships. However, the county with the most mines by far was under a county zoning ordinance, perhaps indicating industry preferences for locations with clear, homogenous rules over patchwork regulation. Rural communities can use the case of frac sand mining as motivation to discuss and plan for sudden land-use predicaments, rather than wait to grapple with unfamiliar legal processes

  14. Frac Sand Mines Are Preferentially Sited in Unzoned Rural Areas.

    Science.gov (United States)

    Locke, Christina

    2015-01-01

    Shifting markets can cause unexpected, stochastic changes in rural landscapes that may take local communities by surprise. Preferential siting of new industrial facilities in poor areas or in areas with few regulatory restrictions can have implications for environmental sustainability, human health, and social justice. This study focuses on frac sand mining-the mining of high-quality silica sand used in hydraulic fracturing processes for gas and oil extraction. Frac sand mining gained prominence in the 2000s in the upper midwestern United States where nonmetallic mining is regulated primarily by local zoning. I asked whether frac sand mines were more commonly sited in rural townships without formal zoning regulations or planning processes than in those that undertook zoning and planning before the frac sand boom. I also asked if mine prevalence was correlated with socioeconomic differences across townships. After creating a probability surface to map areas most suitable for frac sand mine occurrence, I developed neutral landscape models from which to compare actual mine distributions in zoned and unzoned areas at three different spatial extents. Mines were significantly clustered in unzoned jurisdictions at the statewide level and in 7 of the 8 counties with at least three frac sand mines and some unzoned land. Subsequent regression analyses showed mine prevalence to be uncorrelated with land value, tax rate, or per capita income, but correlated with remoteness and zoning. The predicted mine count in unzoned townships was over two times higher than that in zoned townships. However, the county with the most mines by far was under a county zoning ordinance, perhaps indicating industry preferences for locations with clear, homogenous rules over patchwork regulation. Rural communities can use the case of frac sand mining as motivation to discuss and plan for sudden land-use predicaments, rather than wait to grapple with unfamiliar legal processes during a period of

  15. Sustainable water management in Alberta's oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Byers, Bill; Usher, Robyn; Roach, Andrea [CH2M HILL, Englewood, CO (United States); Lambert, Gord; Kotecha, Prit [Suncor Energy Inc., Calgary (Canada)

    2012-07-01

    The Canadian Association of Petroleum Producers forecast published in 2011 predicts that oil production from oil sands will increase by 50% in the next 3 years and double by 2020. This rate of growth will result in significant pressure on water resources; water use per barrel of oil sands production is comparable to other energy resources - about 2.5 barrels of fresh water per barrel of oil produced are used by mining operations and 0.5 barrels by in-situ operations. Suncor Energy Inc. (Suncor) was the first company to develop the oil sands in northern Alberta and holds one of the largest oil sands positions in Canada. In 2010, Suncor announced plans to increase production to more than 1 million barrels of oil equivalent per day by 2020, which it plans to achieve through oil sands production growth of approximately 10% per year. Because water supply and potential impacts to water quality are critical to its future growth, in 2010-2011 Suncor conducted a risk assessment to identify water-related business risks related to its northern Alberta operations. The assessment identified more than 20 high level business risks in strategic water risk areas including water supply, water reuse, storm water management, groundwater, waste management and river water return. The risk assessment results prompted development of a strategic roadmap to guide water stewardship across Suncor's regional operations. The roadmap describes goals, objectives, and specific activities for each of six key water risk areas, and informs prioritization and selection of prospective water management activities. Suncor is not only exploring water within its own boundaries, but is also collaborating with other oil sands producers to explore ways of integrating its water systems through industry consortia; Suncor is a member of the Oil Sands Leadership Initiative and of the recently formed Canadian Oil Sands Innovation Alliance, among others. (author)

  16. A sightability model for mountain goats

    Science.gov (United States)

    Rice, C.G.; Jenkins, K.J.; Chang, W.-Y.

    2009-01-01

    Unbiased estimates of mountain goat (Oreamnos americanus) populations are key to meeting diverse harvest management and conservation objectives. We developed logistic regression models of factors influencing sightability of mountain goat groups during helicopter surveys throughout the Cascades and Olympic Ranges in western Washington during summers, 20042007. We conducted 205 trials of the ability of aerial survey crews to detect groups of mountain goats whose presence was known based on simultaneous direct observation from the ground (n 84), Global Positioning System (GPS) telemetry (n 115), or both (n 6). Aerial survey crews detected 77 and 79 of all groups known to be present based on ground observers and GPS collars, respectively. The best models indicated that sightability of mountain goat groups was a function of the number of mountain goats in a group, presence of terrain obstruction, and extent of overstory vegetation. Aerial counts of mountain goats within groups did not differ greatly from known group sizes, indicating that under-counting bias within detected groups of mountain goats was small. We applied HorvitzThompson-like sightability adjustments to 1,139 groups of mountain goats observed in the Cascade and Olympic ranges, Washington, USA, from 2004 to 2007. Estimated mean sightability of individual animals was 85 but ranged 0.750.91 in areas with low and high sightability, respectively. Simulations of mountain goat surveys indicated that precision of population estimates adjusted for sightability biases increased with population size and number of replicate surveys, providing general guidance for the design of future surveys. Because survey conditions, group sizes, and habitat occupied by goats vary among surveys, we recommend using sightability correction methods to decrease bias in population estimates from aerial surveys of mountain goats.

  17. Constitutive Soil Properties for Mason Sand and Kennedy Space Center

    Science.gov (United States)

    Thomas, Michael A.; Chitty, Daniel E.

    2011-01-01

    Accurate soil models are required for numerical simulations of land landings for the Orion Crew Exploration Vehicle (CEV). This report provides constitutive material models for two soil conditions at Kennedy Space Center (KSC) and four conditions of Mason Sand. The Mason Sand is the test sand for LaRC s drop tests and swing tests of the Orion. The soil models are based on mechanical and compressive behavior observed during geotechnical laboratory testing of remolded soil samples. The test specimens were reconstituted to measured in situ density and moisture content. Tests included: triaxial compression, hydrostatic compression, and uniaxial strain. A fit to the triaxial test results defines the strength envelope. Hydrostatic and uniaxial tests define the compressibility. The constitutive properties are presented in the format of LSDYNA Material Model 5: Soil and Foam. However, the laboratory test data provided can be used to construct other material models. The soil models are intended to be specific to the soil conditions they were tested at. The two KSC models represent two conditions at KSC: low density dry sand and high density in-situ moisture sand. The Mason Sand model was tested at four conditions which encompass measured conditions at LaRC s drop test site.

  18. Sanding dust from nanoparticle-containing paints: Physical characterisation

    International Nuclear Information System (INIS)

    Koponen, I K; Jensen, K A; Schneider, T

    2009-01-01

    Increasing use of nanoparticles in different industrial applications has raised a new potential health risk to the workers as well as to the consumers. This study investigates the particle size distributions of sanding dust released from paints produced with and without engineered nanoparticles. Dust emissions from sanding painted plates were found to consist of five size modes; three modes under 1 μm and two modes around 1 and 2 μm. We observed that the sander was the only source of particles smaller than 50 nm and they dominated the number concentration spectra. Mass and surface area spectra were dominated by the 1 and 2 μm modes. Addition of nanoparticles caused only minor changes in the geometric mean diameters of the particle modes generated during sanding of two paints doped with 17 nm TiO2 and 95 nm Carbon Black nanoparticles as compared to the size modes generated during sanding a conventional reference paint. However, the number concentrations in the different size modes varied considerably in between the two NP-doped paints and the reference paint. Therefore, from a physical point of view, there may be a difference in the exposure risk during sanding surfaces covered with nanoparticle-based paints as compared to sanding conventional paints.

  19. Sources of atmospheric emissions in the Athabasca oil sands region

    International Nuclear Information System (INIS)

    1996-01-01

    An inventory of emissions for the Athabasca oil sands airshed that can be used as a basis for air quality assessments was presented. This report was prepared for the Suncor Steepbank Mine Environmental Impact Assessment (EIA) and for the Syncrude Aurora Mine EIA. Both Syncrude and Suncor have plans to develop new oil sands leases and to increase their crude oil and bitumen production. Suncor has proposed modifications to reduce SO 2 emissions to the atmosphere and Syncrude will develop additional ambient air quality, sulphur deposition and biomonitoring programs to ensure that environmental quality is not compromised because of atmospheric emissions associated with their operations. Major emission sources are controlled and monitored by regulatory statutes, regulations and guidelines. In this report, the following four types of emission sources were identified and quantified: (1) major industrial sources associated with Suncor's and Syncrude's current oil sands operations, (2) fugitive and area emission sources such as volatilization of hydrocarbons from tanks and tailings ponds, (3) other industrial emission sources in the area, including oil sands and non-oil sands related facilities, and (4) highway and residential emission sources. Emissions associated with mining operations include: SO 2 , NO x , CO, and CO 2 . The overall conclusion was that although there are other smaller sources of emissions that can influence air quality, there is no reason to doubt that Suncor and Syncrude oil sands operations are the major sources of emissions to the atmosphere. 13 refs., 12 tabs., 8 figs

  20. Thermal Conductivity of Polymer Composite poypropilene-Sand

    International Nuclear Information System (INIS)

    Betha; Mashuri; Sudirman; Karo Karo, Aloma

    2001-01-01

    Thermal conductivity composite materials polypropylene (PP)-sand have been investigated. PP composite with sand to increase thermal conductivity from the polymer. The composite in this observation is done by mixing matrix (PP melt flow 2/10)and filler sand)by means tool labo plastomil. The result of thermal conductivity is composite of PP-sand which is obtained increase and followed by the raising of filler particle volume fraction. The analysis of thermal conductivity based on the model Cheng and Vachon, model Lewis and Nielsen where this model has the function to support experiment finding. It is proved that Lewis' and Nielsen's model almost approach experiment result. And then thermal conductivity raising will be analyzed by the model of pararel-series conductive with the two (2)phases system. It is showed that sand in PP MF 2 composite have the big role to increase the thermal conductivity than sand in PP MF 10 composition, but it is not easy to shape conductive medium

  1. Evaluation of multistage filtration to reduce sand filter exhaust activity

    International Nuclear Information System (INIS)

    Zippler, D.B.

    1975-01-01

    Air from the Savannah River Plant Fuel Reprocessing facilities is filtered through deep bed sand filters consisting of 8 1 / 2 feet of gravel and sand. These filters have performed satisfactorily for the past 18 years in maintaining radioactive release levels to a minimum. The apparent filter efficiency has been determined for many years by measurements of the quantity of radioactivity in the air stream before and after the filter. Such tests have indicated efficiencies of 99.9 percent or better. Even with sand filter efficiency approaching a single stage HEPA filter, new emphasis on further reduction in release of plutonium activity to the environment prompted a study to determine what value backup HEPA filtration could provide. To evaluate the specific effect additional HEPA filtration would have on the removal of Pu from the existing sand filter exhaust stream, a test was conducted by passing a sidestream of sand-filtered air through a standard 24 x 24 x 11 1 / 2 in. HEPA filter. Isokinetic air samples were withdrawn upstream and downstream of the HEPA filter and counted for alpha activity. Efficiency calculations indicated that backup HEPA filtration could be expected to provide an additional 99 percent removal of the Pu activity from the present sand-filter exhaust. (U.S.)

  2. Depositional environment, sand provenance, and diagenesis of the Basal Salina Formation (lower Eocene), northwestern Peru

    Science.gov (United States)

    Marsaglia, K. M.; Carozzi, A. V.

    The Basal Salina Formation is a lower Eocene transgressive sequence consisting of interbedded shales, siltstones, and conglomeratic sandstones. This formation occurs in the Talara basin of northwestern Peru and is one of a series of complexly faulted hydrocarbon-producing formations within this extensional forearc basin. These sediments were probably deposited in a fan-delta complex that developed along the ancestral Amotape Mountains during the early Eocene. Most of the sediment was derived from the low-grade metamorphic and plutonic rocks that comprise the Amotape Mountains, and their sedimentary cover. Detrital modes of these sandstones reflect the complex tectonic history of the area, rather than the overall forearc setting. Unlike most forearc sediments, these are highly quartzose, with only minor percentages of volcanic detritus. This sand is variably indurated and cemented by chlorite, quartz, calcite, and kaolinite. Clay-mineral matrix assemblages show gradational changes with depth, from primarily detrital kaolinite to diagenetic chlorite and mixed-layered illite/smectite. Basal Salina sandstones exhibit a paragenetic sequence that may be tied to early meteoric influx or late-stage influx of thermally driven brines associated with hydrocarbon migration. Much of the porosity is secondary, resulting from a first-stage dissolution of silicic constituents (volcanic lithic fragments, feldspar, and fibrous quartz) and a later dissolution of surrounding carbonate cement. Types of pores include skeletal grains, grain molds, elongate pores, and fracture porosity. Measured porosity values range up to 24% and coarser samples tend to be more porous. Permeability is enhanced by fractures and deterred by clay-mineral cements and alteration residues.

  3. Notes on the Phlebotomine Sand Flies from the Peruvian Southeast : I. Description of Lutzomyia (Helcocyrtomyia adamsi n. sp. (Diptera: Psychodidae

    Directory of Open Access Journals (Sweden)

    Fernandez R

    1998-01-01

    Full Text Available A new species of phlebotomine sand fly, Lutzomyia adamsi n. sp., is described and illustrated from specimens collected during August 1994, in Sandia, Department of Puno-Peru. According to the Oficina Nacional de Evaluacion de Recursos Naturales(ONERN 1976, this locality is situated in the life zone known as humid, mountain, low tropical forest (bh-MBT. Many areas in the northern part of Puno, mainly in the Inambari and Tambopata basins, are endemic to leishmaniasis. These areas are the continuation of others, largely known as "leishmaniasic" in the departments of Cusco and Madre de Dios. The morphological characteristics indicated that this species belongs to the genus Lutzomyia, subgenus Helcocyrtomyia Barretto, 1962

  4. Suitability of natural soils for foundations for surface facilities at the prospective Yucca Mountain Nuclear Waste Repository

    International Nuclear Information System (INIS)

    Ho, D.M.; Sayre, R.L.; Wu, C.L.

    1986-11-01

    In this report, the natural soils at the Yucca Mountain site are evaluated for the purpose of assessing the suitability of the soils for the foundations of the surface facilities at the prospective repository. The areas being considered for locating the surface facilities are situated on an alluvial plain at the base of Yucca Mountain. Preliminary parameters for foundation design have been developed on the basis of limited field and laboratory study of soils at four test pit locations conducted during May and June 1984. Preliminary recommendations for construction are also included in this report. The gravel-sand alluvial deposits were found to be in a dense to very dense state, which is suitable for foundations of the surface facilities. The design parameters described in this report have been developed for conceptual design, but need to be verified before final design

  5. Vulnerability of soils towards mining operations in gold-bearing sands in Chile

    Science.gov (United States)

    Jordán, Manuel Miguel; González, Irma; Bech, Jaume; Sanfeliu, Teófilo; Pardo, Francisco

    2015-04-01

    The contamination levels in handicraft mining, despite less production and processing less equipment, have high repercussions upon the environment in many cases. High-grade ore extraction, flotation, gravity concentration, acid leaching cementation and mercury amalgamation are the main metallurgical technologies employed. Gold recovery involving milling and amalgamation appears to the most contamination source of mercury. This research work is only a starting point for carrying out a risk probability mapping of pollutants of the gold bearing sands. In southern Chile, with a mild and rainy climate, high levels of pollutants have been detected in some gold placer deposits. The handicraft gold-bearing sands studied are located in X Region of "Los Lagos" in southern Chile. A great quantity of existing secondary deposits in the X Region is located in the coastal mountain range. The lithological units that are found in this range correspond with metamorphic rocks of a Paleozoic crystalline base that present an auriferous content liberated from the successive erosive processes suffered. Metasedimentary and metavolcanic rocks also make up part of this range, but their auriferous load is much smaller. The methodology used in the characterization of the associated mineralization consists of testing samples with a grain size distribution, statistical parameter analysis and mineralogical analysis using a petrographic microscope, XRD and SEM/EDX. The chemical composition was determined by means of XRF and micro-chemical analysis. The major concentrations of heavy minerals are located in areas of dynamic river energy. In the studied samples, more the 75 % of the heavy minerals were distributed among grain sizes corresponding to thin sand (0.25-0.05 mm) with good grain selection. The main minerals present in the selected analysed samples were gold, zircon, olivine, ilmenite, hornblende, hematite, garnet, choromite, augite, epidote, etc. The main heavy metals found were mercury

  6. The extraction of bitumen from western tar sands. Annual report, July 1990--July 1991

    Energy Technology Data Exchange (ETDEWEB)

    Oblad, A.G.; Bunger, J.W.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

    1992-04-01

    Contents of this report include the following: executive summary; characterization of the native bitumen from the Whiterocks oil sand deposit; influence of carboxylic acid content on bitumen viscosity; water based oil sand separation technology; extraction of bitumen from western oil sands by an energy-efficient thermal method; large- diameter fluidized bed reactor studies; rotary kiln pyrolysis of oil sand; catalytic upgrading of bitumen and bitumen derived liquids; ebullieted bed hydrotreating and hydrocracking; super critical fluid extraction; bitumen upgrading; 232 references; Appendix A--Whiterocks tar sand deposit bibliography; Appendix B--Asphalt Ridge tar sand deposit bibliography; and Appendix C--University of Utah tar sands bibliography.

  7. AHP 21: Review: Moving Mountains

    Directory of Open Access Journals (Sweden)

    William B. Noseworthy

    2012-12-01

    Full Text Available Moving Mountains stands out among recent discussions of the Southeast Asian Highlands, drawing from twelve contributors with extensive field experience living and working in locales closed to nonCommunist academics between 1945 and 1990 (3. The authors' methodologies focus on the anthropological approach of participant observation combined with oral history. Previously, substantial research had been confined to the experience of "hill tribes" in Northern Thailand (11, unless one gained access to the massive collections of French language research under the École Française d'Extrême Orient (EFEO or the Société Asiatique (SA, both in Paris. As such, this volume's contributors are able to ring out the voices of Southeast Asian Massif populations in a way that demonstrates a mindful assembly of research, while carefully narrating a more complex view of the region than that presented by Scott's (2009:22 "zones of refuge." ...

  8. Natural analogs for Yucca Mountain

    International Nuclear Information System (INIS)

    Murphy, W.M.

    1995-01-01

    High-level radioactive waste in the US, spent fuels from commercial reactors and nuclear materials generated by defense activities, will remain potentially hazardous for thousands of years. Demonstrable long-term stability of certain geologic and geochemical systems motivates and sustains the concept that high-level waste can be safely isolated in geologic repositories for requisite periods of time. Each geologic repository is unique in its properties and performance with reguard to isolation of nuclear wastes. Studies of processes analogous to waste-form alteration and radioelement transport in environments analogous to Yucca Mountain are being conducted at two sites, described in this article to illustrate uses of natural analog data: the Nopal I uranium deposit in the Sierra Pena Blanca, Mexico, and the Akrotiri archaeological site on the island of Santorini, Greece

  9. Investigation and Evaluation of Geopressured - Geothermal Wells, Final Report; Alice C. Plantation No. 2 Well, St. Mary Parish, Louisiana; Volume 1; Narrative Report

    Energy Technology Data Exchange (ETDEWEB)

    Lohse, Alan; Willits, M.H.

    1978-12-01

    Gruy Federal, Inc. (Gruy) operates under Contract No. EG-77-C-08-1528 to the Department of Energy, Division of Geothermal Energy, to evaluate potential alternate energy sources occurring within geopressured-geothermal (Geo) aquifers in Miocene, Oligocene, Tuscaloosa, Wilcox, and Frio formations along the Texas and Louisiana Gulf Coast. The project is entitled ''Investigation and Evaluation of Geopressured-Geothermal Wells''. The original period of performance was from September 26, 1977, through September 30, 1978; the contract was later extended through September 30, 1979. The first well on which testing was attempted under this contract was the Alice C. Plantation No. 2 Well, located in St. Mary Parish, Louisiana. Originally drilled by the Sun Oil Company to a total depth of 19,000 feet, this well was abandoned as a dry hole in January 1964. Gruy's reentry attempt ended with plugging and abandonment after a saltwater flow on September 17, 1978. This report is a comprehensive document detailing all events and costs relating to the Alice C. plantation well, from its initial selection as a reentry well through the plugging and abandonment operations.

  10. Pipeline corridors through wetlands - impacts on plant communities: Bayou Grand Cane, De Soto Parish, Louisiana. Topical report, August 1991--July 1993

    Energy Technology Data Exchange (ETDEWEB)

    Shem, L.M.; Zimmerman, R.E.; Hayes, D. [Argonne National Lab., IL (United States); Van Dyke, G.D. [Argonne National Lab., IL (United States)]|[Trinity Christian College, Palos Heights, IL (United States)

    1994-12-01

    The goal of the Gas Research Institute Wetland Corridors Program is to document impacts of existing pipeline on the wetlands they traverse. To accomplish this goal, 12 existing wetland crossings were surveyed. These sites varied in elapsed time since pipeline construction, wetland type, pipeline installation techniques, and night of-way (ROW) management practices. This report presents the results of a survey conducted over the period of August 12-13, 1991, at the Bayou Grand Cane crossing in De Soto Parish, Louisiana, where a pipeline constructed three years prior to the survey crosses the bayou through mature bottomland hardwoods. The sit was not seeded or fertilized after construction activities. At the time of sampling, a dense herb stratum (composed of mostly native species) covered the 20-m-wide ROW, except within drainage channels. As a result of the creation of the ROW, new habitat was created, plant diversity increased, and forest habitat became fragmented. The ROW must be maintained at an early stage of succession to allow access to the pipeline however, impacts to the wetland were minimized by decreasing the width of the ROW to 20 m and recreating the drainage channels across the ROW. The canopy trees on the ROW`s edge shaded part of the ROW, which helped to minimize the effects of the ROW.

  11. Pipeline corridors through wetlands - impacts on plant communities: Bayou Pointe Aux Chenes, Terrebonne Parish, Louisiana. Topical report, August 1991--April 1994

    Energy Technology Data Exchange (ETDEWEB)

    Van Dyke, G.D.; Shem, L.M.; Zimmerman, R.E.

    1994-12-01

    The goal of the Gas Research Institute Wetland Corridors Program is to document impacts of existing pipelines on the wetlands they traverse. To accomplish this goal, 12 existing wetland crossings were surveyed. These sites varied in elapsed time since pipeline construction, wetland type, pipeline installation techniques, and night- of-way management practices. This report presents the results of a survey conducted on August 22, 1991, in an emergent intertidal estuarine wetland in Terrebonne Parish, Louisiana. The site includes three pipelines installed between 1958 and 1969. Vegetation within the site comprises three native tidal marsh grasses: Spartina alterniflora, Spartina patens, and Distichlis spicata. All three species occurred over the pipelines, within the right-of-way and in both natural areas. Vegetative differences attributable to the installation or presence of the pipelines were not obvious over the pipelines or in the habitat east of the pipelines. However, because of the presence of a canal west of the 1969 pipeline, vegetation was less abundant in that area, and D. spicata was absent from all but the most distant plots of the transacts. Data obtained in the study indicate that when rights-of-way through brackish marsh are restored to their original elevations, they are revegetated with native vegetation similar to that in surrounding areas.

  12. Thus the Colliers and their wives...': migration, mate choice and population structure of some County Durham parishes in the mid-19th century

    Energy Technology Data Exchange (ETDEWEB)

    M.T. Smith; L.J. Fletcher-Jones [University of Durham, Durham (United Kingdom). Department of Anthropology

    2003-12-01

    Historical accounts of the mining population in County Durham, UK, offer two persistent representations of demographic behaviour - substantial mobility and occupational endogamy - which would influence the distribution of genes in the population. The aim of this paper is to test these predictions against 19th-century demographic data, comparing miners with other contemporary occupations. Four parishes in County Durham yielded data on 3653 birthplace-residence distances, calculated from locations recorded in the 1851 census enumerators' books, and on occupational endogamy and exogamy for 3784 marriages recorded in the Anglican registers, 1834-76. Endogamy was analysed by log-linear models and odds ratios. Median migration distances were similar in the miners and other occupations, though the proportion of migrants among the miners (99.7%) was higher than agricultural (87.0%) and general labourers (91%). Endogamy in the miners (76%) was higher than in other populations, but further analysis showed that the miners' tendency to marry women from the same occupational background was less than among agricultural labourers or professional men.

  13. The Impact of Saffron on Symptoms of Withdrawal Syndrome in Patients Undergoing Maintenance Treatment for Opioid Addiction in Sabzevar Parish in 2017

    Directory of Open Access Journals (Sweden)

    Mohammad Nemat Shahi

    2017-01-01

    Full Text Available Background and Objective. Drug dependence is one of the serious problems around the world. Saffron is one of those beneficial medicinal plants which is embedded with a similar mechanism to methadone (e.g., inhibition of serotonin reuptake. Thus, it can be helpful in reducing the withdrawal symptoms. The aim of this study was to reduce the daily dose of methadone usage and reduce its side effects using saffron in the form of medicinal supplements. Methodology. This study was categorized as a clinical trial. Accordingly, 44 clients of addiction treatment centers in Sabzevar parish were randomly selected to participate in this study in 2016–2017. While the experimental group was treated with methadone syrup and self-made saffron capsules, the control group received methadone syrup and placebo capsules. Results. The results showed that the use of saffron and methadone alleviated the symptoms of withdrawal syndrome (p<0.001. Conclusion. Having reviewed the research participants, it was indicated that the introduction of saffron alleviated the symptoms of withdrawal syndrome in patients undergoing maintenance treatment for opioid addiction. Thus, it seems rational to make use of saffron in combination with methadone in order to alleviate the symptoms of withdrawal syndrome.

  14. A Primer on Alberta’s Oil sands Royalties

    Directory of Open Access Journals (Sweden)

    Sarah Dobson

    2015-12-01

    Full Text Available Fulfilling its campaign promise, the new NDP government announced a review of Alberta’s royalty framework in June 2015. The province receives royalty revenue from three main sources – natural gas, crude oil, and oil sands. Since the 2009-10 fiscal year the largest contributor to Alberta’s royalty revenues has been the oil sands. If you want a sense of how important oil sands royalties have been for Alberta’s finances, consider this: In the 2014–15 fiscal year, the government collected just over $5 billion from oil sands royalties. These royalties covered over 10 per cent of the province’s operational expenses of $48.6 billion in the same fiscal year. Over the last six fiscal years the oil sands have contributed an average of 10 per cent of revenues to provincial coffers. This makes oil sands royalties the fourth largest contributor behind personal income taxes (23 per cent, federal transfers (13 per cent and corporate income taxes (11 per cent. But how many Albertans really understand how the royalty system works? What do we mean when we say “royalty”? How does the Alberta Government calculate royalties on oil sands producers? If the system is going to change, it’s important that Albertans understand how the current system works. That is what this paper is designed to do. For Albertans to properly judge the impact of new policy, they need a solid understanding of the current policy environment. We all know that oil prices have dropped and oil sands producers are losing profitability. As such, changes to the royalty system could have a deep and profound impact on the sector. Here are some of the issues this primer will study: • Pre-payout projects vs. post-payout projects, in other words, the classification of projects for royalty purposes based on whether the cumulative costs of a project exceed its cumulative revenues • Monthly payment of royalties vs. annual payment • Understanding the unit price of bitumen and how that

  15. Occupational Health in Mountainous Kyrgyzstan.

    Science.gov (United States)

    Dzhusupov, Kenesh O; Colosio, Claudio; Tabibi, Ramin; Sulaimanova, Cholpon T

    2015-01-01

    In the period of transition from a centralized economy to the market economy, occupational health services in Kyrgyzstan have survived through dramatic, detrimental changes. It is common for occupational health regulations to be ignored and for basic occupational health services across many industrial enterprises and farms to be neglected. The aim of this study was to demonstrate the present situation and challenges facing occupational health services in Kyrgyzstan. The transition from centralized to the market economy in Kyrgyzstan has led to increased layoffs of workers and unemployment. These threats are followed by increased workload, and the health and safety of workers becomes of little concern. Private employers ignore occupational health and safety; consequently, there is under-reporting of occupational diseases and accidents. The majority of enterprises, especially those of small or medium size, are unsanitary, and the health status of workers remains largely unknown. The low official rates of occupational diseases are the result of data being deliberately hidden; lack of coverage of working personnel by medical checkups; incompetent management; and the poor quality of staff, facilities, and equipment. Because Kyrgyzstan is a mountainous country, the main environmental and occupational factor of enterprises is hypoxia. Occupational health specialists have greatly contributed to the development of occupational medicine in the mountains through science and practice. The enforcement of existing strong occupational health legislation and increased financing of occupational health services are needed. The maintenance of credible health monitoring and effective health services for workers, re-establishment of medical services and sanitary-hygienic laboratories in industrial enterprises, and support for scientific investigations on occupational risk assessment will increase the role of occupational health services in improving the health of the working population

  16. Simulating Sand Behavior through Terrain Subdivision and Particle Refinement

    Science.gov (United States)

    Clothier, M.

    2013-12-01

    Advances in computer graphics, GPUs, and parallel processing hardware have provided researchers with new methods to visualize scientific data. In fact, these advances have spurred new research opportunities between computer graphics and other disciplines, such as Earth sciences. Through collaboration, Earth and planetary scientists have benefited by using these advances in hardware technology to process large amounts of data for visualization and analysis. At Oregon State University, we are collaborating with the Oregon Space Grant and IGERT Ecosystem Informatics programs to investigate techniques for simulating the behavior of sand. In addition, we have also been collaborating with the Jet Propulsion Laboratory's DARTS Lab to exchange ideas on our research. The DARTS Lab specializes in the simulation of planetary vehicles, such as the Mars rovers. One aspect of their work is testing these vehicles in a virtual "sand box" to test their performance in different environments. Our research builds upon this idea to create a sand simulation framework to allow for more complex and diverse environments. As a basis for our framework, we have focused on planetary environments, such as the harsh, sandy regions on Mars. To evaluate our framework, we have used simulated planetary vehicles, such as a rover, to gain insight into the performance and interaction between the surface sand and the vehicle. Unfortunately, simulating the vast number of individual sand particles and their interaction with each other has been a computationally complex problem in the past. However, through the use of high-performance computing, we have developed a technique to subdivide physically active terrain regions across a large landscape. To achieve this, we only subdivide terrain regions where sand particles are actively participating with another object or force, such as a rover wheel. This is similar to a Level of Detail (LOD) technique, except that the density of subdivisions are determined by

  17. AN EXPERIMENTAL STUDY ON STRENGTH PARAMETRES OF CONCRETE WITH REPLACMENT OF FINE AGGREGATE BY ROBO SAND

    OpenAIRE

    T.Dilip Kumar *1 & G.Kalyan 2

    2018-01-01

    Concrete is the most widely used composite construction material. Fine aggregate plays a very important role for imparting better properties to concrete in its fresh and hardened state. Generally, river sand was used as fine aggregate for construction. Due to the continuous mining of sand from riverbed led to the depletion of river sand and it became a scarce material. Also, samining from river bed caused a lot of environmental issues. As a substitute to river sand, Robo sand has been used. I...

  18. Mineralogy and Genesis of Heavy Minerals in Coastal Dune Sands, South Eastern Qatar

    OpenAIRE

    Nasir, Sobhi J. [صبحي جابر نصر; El-Kassas, Ibrahim A.; Sadiq, A. Ali M.

    1999-01-01

    Large amounts of aeolian sand occur in the southeastern coastal zone of Qatar Peninsula as sand dunes accumulated in a vast sand field locally called " Niqyan Qatar ". The present work, carried out on a sand dune belt of this field near Mesaied Industrial City, revealed the distribution of heavy minerals shows a regional variability induced by provenance and local variability reflecting genetic differences. The studied dune sands are rich in shells of pelecypods, with the light mineral assemb...

  19. Ecogeomorphology of Sand Dunes Shaped by Vegetation

    Science.gov (United States)

    Tsoar, H.

    2014-12-01

    Two dune types associated with vegetation are known: Parabolic and Vegetated Linear Dunes (VLDs), the latters are the dominant dune type in the world deserts. Parabolic dunes are formed in humid, sub-humid and semi-arid environments (rather than arid) where vegetation is nearby. VLDs are known today in semiarid and arid lands where the average yearly rainfall is ≥100 mm, enough to support sparse cover of vegetation. These two dune types are formed by unidirectional winds although they demonstrate a different form and have a distinct dynamics. Conceptual and mathematical models of dunes mobility and stability, based on three control parameters: wind power (DP), average annual precipitation (p), and the human impact parameter (μ) show that where human impact is negligible the effect of wind power (DP) on vegetative cover is substantial. The average yearly rainfall of 60-80 mm is the threshold of annual average rainfall for vegetation growth on dune sand. The model is shown to follow a hysteresis path, which explains the bistability of active and stabilized dunes under the same climatic conditions with respect to wind power. We have discerned formation of parabolic dunes from barchans and transverse dunes in the coastal plain of Israel where a decrease in human activity during the second half of the 20th century caused establishment of vegetation on the crest of the dunes, a process that changed the dynamics of these barchans and transverse dunes and led to a change in the shape of the windward slope from convex to concave. These dunes gradually became parabolic. It seems that VLDs in Australia or the Kalahari have always been vegetated to some degree, though the shrubs were sparser in colder periods when the aeolian erosion was sizeable. Those ancient conditions are characterized by higher wind power and lower rainfall that can reduce, but not completely destroy, the vegetation cover, leading to the formation of lee (shadow) dunes behind each shrub. Formation of

  20. Uranium and Thorium in zircon sands processed in Northeastern Brazil

    International Nuclear Information System (INIS)

    Hazin, Clovis A.; Farias, Emerson E. G. de

    2008-01-01

    Zircon the main mineral of zirconium is a silicate mineral product (ZrSiO 4 ) obtained from beach sand deposits, along with other minerals such as kyanite, ilmenite, and rutile. All zircons contain some radioactive impurities due to the presence of uranium, thorium and their respective decay products in the crystalline structure of zircon, as well as potassium-40. Uranium and thorium substitute Zr 4+ in the mineral through an internal process called isomorphous replacement of zirconium. For this study, samples were collected both from a mineral sand processing plant located in the coastal region of Northeastern brazil and from the beach sands used in the process. The aim of this study was to assess the 238 U, 232 Th and 40 K contents in the beach sands and in the mineral products extracted from the sands in that facility, with special emphasis on zircon. Measurements were performed through gamma spectrometry, by using a high-purity germanium detector (HPGe) coupled to a multichannel analyzer. Activity concentration for 238 U and 232 Th in zircon sands ranged from 5462±143 to 19286±46 Bq kg -1 and from 1016±7 to 7162±38 Bq kg -1 , respectively. For 40 K, on the other hand, activity concentration values ranged from 81±14 to 681±26 Bq Kg -1 . The results of the measurements carried out for raw sand samples showed activity concentrations between 2.7±0.6 and 7.9±0.9 Bq kg -1 and 6.5±0.4 and 9.4±0.6 Bq kg -1 for 238 U and 23T h respectively, and from 48.8±3.1 to 76.1±2.4 Bq kg -1 for 40 K. Activity concentrations of 238 U and 232 Th in kyanite, ilmenite and rutile samples were also determined. (author)

  1. Gravel Mobility in a High Sand Content Riverbed

    Science.gov (United States)

    Haschenburger, J. K.

    2017-12-01

    In sand-gravel channels, sand may modify gravel transport by changing conditions of entrainment and promoting longer displacements or gravel may inhibit sand transport if concentrated into distinct deposits, which restrict sand supply with consequences for migrating bedform size or form. This study reports on gravel mobility in the lower San Antonio River, Texas, where gravel content in the bed material ranges from about 1% to more than 20%. Sediment transport observations were collected at three U.S. Geological Survey gauging stations by deploying a Helley-Smith sampler with a 0.2 mm mesh bag from which transport rates and mobile grain sizes were determined. The flow rates sampled translate into an annual exceedance expectation from 0.2% to 98%. Gravel transport rates are generally two orders of magnitude smaller than the rates of sand transport. However, the finest gravels are transported at rates on the same order of magnitude as the coarsest sands. At all sites, the 2 and 2.8 mm fractions are transported at the lowest flow rate sampled, suggesting mobility for at least 38% to as much as 98% of the year. Fractions as large as 8 mm are mobilized at flow rates that are expected between 25% and 53% of the year. The largest fractions captured in the sampling (16 to 32 mm) require flows closer to bankfull conditions that occur no more than 0.8% of the year. Results document that some gravel sizes can be frequently transported in low gradient riverbeds with high sand content.

  2. Economic impacts of Alberta's oil sands, volume 1

    International Nuclear Information System (INIS)

    Timilsina, G.R.; LeBlanc, N.; Walden, T.

    2005-01-01

    In 2004, the international media recognized Alberta's oil sands as part of the global oil reserves, thereby establishing Canada as second to Saudi Arabia as potential oil producing nations. The economic impacts of Alberta's oil sands industry on economies were assessed at regional, provincial and international levels for the 2000 to 2020 period. A customized input-output model was used to assess economic impacts, which were measured in terms of changes in gross domestic product; employment and labour income; and, government revenues. Cumulative impacts on employment by sector and by jurisdiction were also presented. An investment of $100 billion is expected through 2020, resulting in production of crude bitumen and synthetic crude oil outputs valued at about $531 billion. The impact of the oil sands industry on local employment was also evaluated. It was shown that activities in the oil sands industry will lead to significant economic impact in Alberta, Ontario, Quebec and the rest of Canada. Alberta's local economy would be the main beneficiary of oil sands activities with nearly 3.6 million person years employment created in Alberta during the 2000 to 2020. Another 3 million person years employment would be created in other Canadian provinces and outside Canada during the same time period. A sensitivity analysis on the responsiveness to oil prices and the removal of various constraints incorporated in the main analysis was also presented. The federal government will be the largest recipient of revenues generated to to oil sands activities. The results of the study were compared with that of the National Task Force on Oil Sands Strategies. This first volume revealed the results of the study while the second volume includes the data and detailed results. 48 refs., 57 tabs., 28 figs

  3. Selected parameters of moulding sands for designing quality control systems

    Directory of Open Access Journals (Sweden)

    J. Jakubski

    2010-07-01

    Full Text Available One of the modern methods of production optimisation are artificial neural networks. Neural networks owe their popularity to the fact thatthey are convenient tools, which can be utilised in a wide scope of problems. They are capable of reflecting complex functions. Especiallytheir non-linearity should be emphasised. They are gaining wider and wider application in the foundry industry, among others, to controlmelting processes in cupolas and arc furnaces, designing castings and supply systems, control of moulding sands treatments, prediction ofproperties of cast alloys as well as selecting die casting.An attempt of the application neural networks to the quality control of moulding sands with bentonite is presented in the paper. This isa method of assessing the suitability of moulding sands by finding correlations in between individual parameters, by means of artificialneural network systems. The presented investigations were performed with the application of the Statistica 8.0 program.The investigations were aimed at the selection of the proper kind of a neural network for prediction a sand moistness on the bases ofcertain moulding sand properties such as: permeability, compactibility and friability. These parameters – determined as sand moistness functions - were introduced as initial parameters.Application of the Statistica program allowed for an automatic selection of the most suitable network for the reflection of dependencies and interactions existing among the proposed parameters. The best results were obtained for unidirectional multi-layer perception network (MLP. The neural network sensitivity to individual moulding sand parameters was determined, which allowed to reject not important parameters when constructing the network.

  4. Mountain laurel toxicosis in a dog.

    Science.gov (United States)

    Manhart, Ingrid O; DeClementi, Camille; Guenther, Christine L

    2013-01-01

    To describe a case of mountain laurel (Kalmia latifolia) toxicosis in a dog, including case management and successful outcome. A dog presented for vomiting, hematochezia, bradycardia, weakness, and ataxia, which did not improve with supportive treatment. Mountain laurel ingestion was identified as cause of clinical signs after gastrotomy was performed to remove stomach contents. Supportive treatment was continued and the dog made a full recovery. This report details a case of mountain laurel toxicosis in a dog, including management strategies and outcome, which has not been previously published in the veterinary literature. © Veterinary Emergency and Critical Care Society 2013.

  5. Transport of neptunium through Yucca Mountain tuffs

    International Nuclear Information System (INIS)

    Triay, I.R.; Robinson, B.A.; Mitchell, A.J.; Overly, C.M.; Lopez, R.M.

    1993-01-01

    Neptunium has a high solubility in groundwaters from Yucca Mountain [1]. Uranium in nuclear reactors produces 237 Np which has a half-life of 2.1 4 x 10 6 years. Consequently, the transport of 237 Np through tuffs is of major importance in assessing the performance of a high-level nuclear waste repository at Yucca Mountain. The objective of this work is to determine the amount of Np retardation that is provided by the minerals in Yucca Mountain tuffs as a function of groundwater chemistry

  6. Numerical simulation of wind-sand movement in the reversed flow region of a sand dune with a bridge built downstream.

    Science.gov (United States)

    He, Wei; Huang, Ning; Xu, Bin; Wang, Wenbo

    2018-04-23

    A bridge built inside the reversed flow region of a sand dune will change the characteristics of wind-sand movement in this region. The Reynolds-averaged Navier-Stokes simulation and discrete particle tracing are used to simulate the wind-sand movement around a sand dune with a bridge built inside the reversed region. Three cases with different bridge positions are studied. The results show that 1) compared with the isolated dune case, a tall bridge built at the leeward toe leads to an increase in the deposition rate on the leeward slope and a longer reversed flow region downstream of the sand dune; meanwhile, the high speed of crosswind on the bridge indicates that some measures should be taken to protect trains from strong crosswind; 2) a low bridge at the leeward toe has little effect on the sand deposition and reversed flow region of the dune; however, low sand transport rate and crosswind speed on the bridge show that anti-crosswind/sand measures should be taken according to the actual situation and 3) a low bridge on the leeward slope has little effect on the length of reversed flow region, however, high crosswind speed and sand flux on the bridge reveal the need of anti-crosswind/sand measures on the bridge. Moreover, the bridges in the reversed flow region increase the sand flux near the leeward crest; as a result, the moving patterns of the sand dune are changed.

  7. Engineering report on drilling in the Sand Wash Basin intermediate grade project

    International Nuclear Information System (INIS)

    1980-09-01

    The Sand Wash Basin Intermediate Grade Drilling Project was conducted by Bendix Field Engineering Corporation in support of the US Department of Energy (DOE) National Uranium Resource Evaluation (NURE) program. This project consisted of 19 drill holes ranging in depth from 275 to 1220 feet (83.9 to 372.1 m). A total of 11,569 feet (3528.5 m) was rotary drilled and 130 feet (39.7 m) were cored for a total of 11,699 feet (3568.2 m) for the project. The project objective was to provide comprehensive subsurface geologic data relevant to Intermediate Grade uranium mineralization of the Browns Park Formation in the Sugar Loaf Peak Site A, and the Little Juniper Mountain Site B areas. All boreholes are located on the USGS Juniper Hot Springs and the Lay 7.5-Minute Series (Topographic) Quadrangles. The project began May 2, 1980; drilling was completed June 3, 1980. Site restoration and clean up was initiated immediately upon the completion of the last borehole and was completed June 8, 1980

  8. Distribution of phlebotomine sand fly genotypes (Lutzomyia shannoni, Diptera: Psychodidae) across a highly heterogeneous landscape.

    Science.gov (United States)

    Mukhopadhyay, J; Ghosh, K; Ferro, C; Munstermann, L E

    2001-03-01

    Genetic variability of eight Colombian field populations and two laboratory colonies of a tropical forest sand fly, Lutzomyia shannoni Dyar, was assessed by comparing allozyme frequencies at 20 enzyme loci. Substantial genetic variability was noted in all strains, with mean heterozygosities of 13-21% and alleles per locus of 2.0-2.8. Four loci were monomorphic. Six populations in north and central Colombia showed close genetic similarity (Nei's distances, 0.01-0.09), despite mountainous environment, discontinuous forest habitat, and elevation differences from 125 to 1,220 m. Two samples representing the Orinoco (near Villavicencio) and Amazon (near Leticia) river basins were similar (Nei's distance, 0.08) but diverged substantially from the central six samples (Nei's distances, 0.26-0.40). Although the range of L. shannoni extends from the southeastern United States to northern Argentina, three genetically distinct, geographically discrete, groups were discerned by the current analysis: Orinoco-Amazon river basins, north-central Colombia, and eastern United States.

  9. Gassmann Modeling of Acoustic Properties of Sand-clay Mixtures

    Science.gov (United States)

    Gurevich, B.; Carcione, J. M.

    The feasibility of modeling elastic properties of a fluid-saturated sand-clay mixture rock is analyzed by assuming that the rock is composed of macroscopic regions of sand and clay. The elastic properties of such a composite rock are computed using two alternative schemes.The first scheme, which we call the composite Gassmann (CG) scheme, uses Gassmann equations to compute elastic moduli of the saturated sand and clay from their respective dry moduli. The effective elastic moduli of the fluid-saturated composite rock are then computed by applying one of the mixing laws commonly used to estimate elastic properties of composite materials.In the second scheme which we call the Berryman-Milton scheme, the elastic moduli of the dry composite rock matrix are computed from the moduli of dry sand and clay matrices using the same composite mixing law used in the first scheme. Next, the saturated composite rock moduli are computed using the equations of Brown and Korringa, which, together with the expressions for the coefficients derived by Berryman and Milton, provide an extension of Gassmann equations to rocks with a heterogeneous solid matrix.For both schemes, the moduli of the dry homogeneous sand and clay matrices are assumed to obey the Krief's velocity-porosity relationship. As a mixing law we use the self-consistent coherent potential approximation proposed by Berryman.The calculated dependence of compressional and shear velocities on porosity and clay content for a given set of parameters using the two schemes depends on the distribution of total porosity between the sand and clay regions. If the distribution of total porosity between sand and clay is relatively uniform, the predictions of the two schemes in the porosity range up to 0.3 are very similar to each other. For higher porosities and medium-to-large clay content the elastic moduli predicted by CG scheme are significantly higher than those predicted by the BM scheme.This difference is explained by the fact

  10. Coastal geology and recent origins for Sand Point, Lake Superior

    Science.gov (United States)

    Fisher, Timothy G.; Krantz, David E.; Castaneda, Mario R.; Loope, Walter L.; Jol, Harry M.; Goble, Ronald J.; Higley, Melinda C.; DeWald, Samantha; Hansen, Paul

    2014-01-01

    Sand Point is a small cuspate foreland located along the southeastern shore of Lake Superior within Pictured Rocks National Lakeshore near Munising, Michigan. Park managers’ concerns for the integrity of historic buildings at the northern periphery of the point during the rising lake levels in the mid-1980s greatly elevated the priority of research into the geomorphic history and age of Sand Point. To pursue this priority, we recovered sediment cores from four ponds on Sand Point, assessed subsurface stratigraphy onshore and offshore using geophysical techniques, and interpreted the chronology of events using radiocarbon and luminescence dating. Sand Point formed at the southwest edge of a subaqueous platform whose base is probably constructed of glacial diamicton and outwash. During the post-glacial Nipissing Transgression, the base was mantled with sand derived from erosion of adjacent sandstone cliffs. An aerial photograph time sequence, 1939–present, shows that the periphery of the platform has evolved considerably during historical time, infl uenced by transport of sediment into adjacent South Bay. Shallow seismic refl ections suggest slump blocks along the leading edge of the platform. Light detection and ranging (LiDAR) and shallow seismic refl ections to the northwest of the platform reveal large sand waves within a deep (12 m) channel produced by currents fl owing episodically to the northeast into Lake Superior. Ground-penetrating radar profi les show transport and deposition of sand across the upper surface of the platform. Basal radiocarbon dates from ponds between subaerial beach ridges range in age from 540 to 910 cal yr B.P., suggesting that Sand Point became emergent during the last ~1000 years, upon the separation of Lake Superior from Lakes Huron and Michigan. However, optically stimulated luminescence (OSL) ages from the beach ridges were two to three times as old as the radiocarbon ages, implying that emergence of Sand Point may have begun

  11. Geophysics comes of age in oil sands development

    Energy Technology Data Exchange (ETDEWEB)

    Bauman, P. [WorleyParsons Komex, Calgary, AB (Canada); Birch, R.; Parker, D.; Andrews, B. [Calgary Univ., AB (Canada). Dept. of Geology and Geophysics

    2008-07-01

    This paper discussed geophysical techniques developed for oil sands exploration and production applications in Alberta's oil sands region. Geophysical methods are playing an important role in mine planning, tailings containment, water supply, and land reclamation activities. Geophysics techniques are used to estimate the volume of muskeg that needs to be stripped and stored for future reclamation activities as well as to site muskeg piles and delineate the thickness of clay Clearwater formations overlying Cretaceous oil-bearing sands. 2-D electrical resistivity mapping is used to map river-connected deep bedrock Pleistocene paleovalleys in the region. Geophysical studies are also used to investigate the interiors of dikes and berms as well as to monitor salt migration within tailings piles. Sonic and density logs are used to create synthetic seismograms for mapping the Devonian surface in the region. The new applications included the calculation of bitumen saturation from surface sands and shales; muskeg thickness mapping; and non-intrusive monitoring of leachate plumes. Geophysical techniques included 2-D electrical resistivity imaging; transient electromagnetic (EM) technologies; ground penetrating radar; and high-resolution seismic reflections. Polarization, surface nuclear magnetic resonance and push-probe sensing techniques were also discussed. Techniques were discussed in relation to Alberta's Athabasca oil sands deposits. 4 refs.

  12. Geophysical applications for oil sand mine tailings management

    Energy Technology Data Exchange (ETDEWEB)

    Parker, D.; Bauman, P. [WorleyParsons, Calgary, AB (Canada)

    2009-07-01

    Geophysical techniques are applied throughout a mine's life cycle to facilitate siting, constructing and monitoring of tailings dumps and ponds. This presentation described 3 case studies from the Athabasca region in northeast Alberta that demonstrated some of the concerns associated with oil sand mine tailings, and the information that geophysical surveys can provide. The objectives of these studies were to determine the lateral and depth extents of elevated conductivities of soil and groundwater that have high salt concentration from the tailings sand pore fluid. Due to high chloride concentrations within the tailings material, salt within the root zone may affect vegetation. A terrain conductivity survey was designed to map the lateral extents of salinity impact, while an electrical resistivity tomography (ERT) survey was used to delineate the tailings sand leachate at depth. The proper management of oil sand tailings facilities is vital to the life cycle of a mine. It was concluded that geophysical techniques can be instrumental in managing several engineering and environmental challenges, from Pleistocene channel mapping, to tailings pond settling characteristics, to reclaiming tailings sands. 1 ref., 7 figs.

  13. Seismic stochastic inversion identify river channel sand body

    Science.gov (United States)

    He, Z.

    2015-12-01

    The technology of seismic inversion is regarded as one of the most important part of geophysics. By using the technology of seismic inversion and the theory of stochastic simulation, the concept of seismic stochastic inversion is proposed.Seismic stochastic inversion can play an significant role in the identifying river channel sand body. Accurate sand body description is a crucial parameter to measure oilfield development and oilfield stimulation during the middle and later periods. Besides, rational well spacing density is an essential condition for efficient production. Based on the geological knowledge of a certain oilfield, in line with the use of seismic stochastic inversion, the river channel sand body in the work area is identified. In this paper, firstly, the single river channel body from the composite river channel body is subdivided. Secondly, the distribution of river channel body is ascertained in order to ascertain the direction of rivers. Morever, the superimposed relationship among the sand body is analyzed, especially among the inter-well sand body. The last but not at the least, via the analysis of inversion results of first vacuating the wells and continuous infilling later, it is meeted the most needs well spacing density that can obtain the optimal inversion result. It would serve effective guidance for oilfield stimulation.

  14. Sulphur output from oil sands : dramatically changing Alberta's sulphur balance

    International Nuclear Information System (INIS)

    D'Aquin, G.

    2008-01-01

    This paper discussed sulphur production from Alberta's gas and oil sands industries. While sulfur derived from natural gas production in the province is expected to decline as natural gas reserves diminish, Alberta's oil sands contain high amounts of sulphur. It is not yet known how much sulphur will be produced from the province's oil sands facilities. Alberta had considerable stockpiles of sulphur in the 1970s. By 1980, inventories began to decline. By 1996, output had increased to 7.1 million tonnes. Alberta's sulphur inventory reached 9.7 million tonnes following the collapse of the Soviet Union's government mandated fertilizer industry. In 2006, sulphur supplies in Alberta reached 12 million tonnes. Reduced global output has now lowered sulphur stockpiles. Increases in sulphur prices tend to reduce market demand, and lower prices will not typically change the volume of sulphur produced as a byproduct of oil and gas operations. Bitumen-derived sulphur output is expected to exceed gas-derived sulphur output in the near future. Sulphur from oil sands processing is expected to increase by 5 million tonnes by 2017. Increased sulphur production levels in Alberta will present a significant challenge for all sectors of the hydrocarbon industry. It was concluded that developing a plan for storing, selling or disposing of the sulphur will help to ensure the profitability of oil sands operations

  15. Efficiency of Micro-fine Cement Grouting in Liquefiable Sand

    International Nuclear Information System (INIS)

    Mirjalili, Mojtaba; Mirdamadi, Alireza; Ahmadi, Alireza

    2008-01-01

    In the presence of strong ground motion, liquefaction hazards are likely to occur in saturated cohesion-less soils. The risk of liquefaction and subsequent deformation can be reduced by various ground improvement methods including the cement grouting technique. The grouting method was proposed for non-disruptive mitigation of liquefaction risk at developed sites susceptible to liquefaction. In this research, a large-scale experiment was developed for assessment of micro-fine cement grouting effect on strength behavior and liquefaction potential of loose sand. Loose sand samples treated with micro-fine grout in multidirectional experimental model, were tested under cyclic and monotonic triaxial loading to investigate the influence of micro-fine grout on the deformation properties and pore pressure response. The behavior of pure sand was compared with the behavior of sand grouted with a micro-fine cement grout. The test results were shown that cement grouting with low concentrations significantly decreased the liquefaction potential of loose sand and related ground deformation

  16. The use of stable isotopes to trace oil sands constituents

    International Nuclear Information System (INIS)

    Farwell, A.J.; Nero, V.; Dixon, D.G.

    2002-01-01

    A study was conducted to determine the biological effects of oil sands mining operations on aquatic ecosystems. The study focused on the Athabasca oil sand deposit, the largest of 4 deposits in northern Alberta. In particular, the study examined the cycling of oil sand constituents in Benthic invertebrates collected from test pits at Syncrude Canada Ltd.. The invertebrates were similar in size, but different in the quantity of process-affected water or mature fine tailings containing residual bitumen. Dragonflies and damselflies in particular, showed trends of depletion for the carbon 13 isotope and enrichment in nitrogen 15 isotope in pits where levels of process affected water was high. The depletion of carbon 13 isotope suggests that oil sand constituents assimilate into the benthic food chain. The greatest carbon 13 depletion, which was approximately 27 per cent, was found to be in test pits with high turbidity. This implies that oil sands constituents degrade microbially instead of by photosynthetic production. All benthic invertebrate group demonstrated an incremental enrichment in nitrogen 15 isotope from the control pit to the pit with greatest levels of mature fine tailings

  17. Alberta's oil sands fiscal system : historical context and system performance

    International Nuclear Information System (INIS)

    2007-01-01

    This report described the fiscal system applied to Alberta's oil sands. It is the first technical report forming part of a series designed to provide information and to invite comment as part of the Government of Alberta's public review of the fiscal system applied to the province's oil and gas resources. Specifically, this report assessed the robustness of Alberta's oil sands fiscal system and assessed how the regime balanced the risks and rewards to both investors and Albertans across a range of expected and probable economic outcomes. The report provided an explanation of the history and context of Alberta's royalty regime and included a case-by-case approach. It also provided a discussion of the oil sands fiscal system description. Next, it described the methodology employed for the analysis of the oil sands fiscal system. It also provided the assumptions for 5 scenario cases and presented the fiscal map approach for assessing project economics and fiscal system performance. Last, summary observations were presented. It was found that the oil sands fiscal system is very flexible for adverse economic conditions and much less so for highly profitable conditions. tabs., figs

  18. Effects of sand fences on coastal dune vegetation distribution

    Science.gov (United States)

    Grafals-Soto, Rosana

    2012-04-01

    Sand fences are important human adjustments modifying the morphology of developed shores. The effects of sand fences on sediment transport and deposition in their initial stages have been well studied, but little is known about the effect of deteriorated sand fences that have become partially buried low scale barriers within the dune, potentially benefiting vegetation growth by protecting it from onshore stress. Data on vegetation, topography and fence characteristics were gathered at three dune sites in Ocean City, New Jersey on September 2007 and March 2008 to evaluate the effect of fences within the dune on vegetation distribution. Variables include: distance landward of dune toe, degree of sheltering from onshore stressors, net change in surface elevation (deposition or erosion), vegetation diversity and density, presence of remnant fence, and distance landward of fence. Results for the studied environment reveal that 1) vegetation diversity or density does not increase near remnant fences because most remnants are lower than average vegetation height and can not provide shelter; but 2) vegetation distribution is related to topographic variables, such as degree of sheltering, that are most likely the result of sand accretion caused by fence deployment. Fence deployment that prioritizes the creation of topographically diverse dunes within a restricted space may increase the diversity and density of the vegetation, and the resilience and value of developed dunes. Managers should consider the benefits of using sand fences on appropriately wide beaches to create a protective dune that is also diverse, functional and better able to adapt to change.

  19. The extraction of bitumen from western oil sands

    International Nuclear Information System (INIS)

    Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

    1992-08-01

    The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximately 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report

  20. Improving the geotechnical behavior of sand through cohesive admixtures

    Directory of Open Access Journals (Sweden)

    Mohie eldin Mohamed Afify Elmashad

    2018-04-01

    Full Text Available Irrigation projects in Egypt have been facing tremendous challenges, mostly is the scarcity of irrigation water. The current research presents the effect of different cohesive admixture on the conductivity of siliceous sand in general and its other geotechnical properties. Two different types of conventional swelling clay from (Toshka, 6th of October as well as bentonite were used to construct the irrigation canals and embankment. The results indicated that increase in the plasticity properties of the treated soil also decrease the permeability and infiltration. Moreover, the dry density of 2.08 t/m3 was obtained from sand and 20% 6th of October mixture, also the CBR of 31.20% were obtained from sand and 8% 6th of October mixture. Increasing the bentonite ratio increases the cohesion and decreasing the permeability. The swelling ratios of sand 6th of October Clay mixture is equal to 0.28%, and the fictitious stress at which the swelling ratio is nil, is equal to 16 kPa. Keywords: Sand, Swelling clay, Bentonite, Compaction test, Consolidation test, Triaxial test