WorldWideScience

Sample records for sand motion initiation

  1. INITIATION OF SHELL MOTION ON SAND BEDS: AN EXPERIMENTAL STUDY

    Institute of Scientific and Technical Information of China (English)

    Subhasish DEY; Alok KUMAR

    2002-01-01

    Experimental study on initiation of bivalve shell motion on a horizontal sand bed, under a unidirectional flow of water, is presented. Experiments were carried out in a flume with three types of bivalve shells,namely Coquina Clam, Cross-barred Chione and Ponderous Ark, to test the condition for initiation of motion. The shape parameters of bivalve shells are defined appropriately. Experiments were conducted in a flume with a horizontal bed, and the critical shear stresses were estimated using Vanoni's side-wall correction. The characteristic parameters affecting the initiation of shell motion on a horizontal bed in rough-turbulent regime identified based on the physical reasoning and dimensional analysis are the Shields parameter (nondimensional critical shear stress), nondimensional competent mean velocity,nondimensional sand roughness, nondimensional flow depth and shape parameter. Equations of Shields parameter and nondimensional competent mean velocity for the initial movement of shells on a horizontal sand bed with convex upward and downward conditions are obtained using experimental data.

  2. Incipient Motion of Sand and Oil Agglomerates

    Science.gov (United States)

    Nelson, T. R.; Dalyander, S.; Jenkins, R. L., III; Penko, A.; Long, J.; Frank, D. P.; Braithwaite, E. F., III; Calantoni, J.

    2016-12-01

    Weathered oil mixed with sediment in the surf zone in the northern Gulf of Mexico after the 2010 Deepwater Horizon oil spill, forming large mats of sand and oil. Wave action fragmented the mats into sand and oil agglomerates (SOAs) with diameters of about 1 to 10 cm. These SOAs were transported by waves and currents along the Gulf Coast, and have been observed on beaches for years following the spill. SOAs are composed of 70%-95% sand by mass, with an approximate density of 2107 kg/m³. To measure the incipient motion of SOAs, experiments using artificial SOAs were conducted in the Small-Oscillatory Flow Tunnel at the U.S. Naval Research Laboratory under a range of hydrodynamic forcing. Spherical and ellipsoidal SOAs ranging in size from 0.5 to 10 cm were deployed on a fixed flat bed, a fixed rippled bed, and a movable sand bed. In the case of the movable sand bed, SOAs were placed both proud and partially buried. Motion was tracked with high-definition video and with inertial measurement units embedded in some of the SOAs. Shear stress and horizontal pressure gradients, estimated from velocity measurements made with a Nortek Vectrino Profiler, were compared with observed mobility to assess formulations for incipient motion. For SOAs smaller than 1 cm in diameter, incipient motion of spherical and ellipsoidal SOAs was consistent with predicted critical stress values. The measured shear stress at incipient motion of larger, spherical SOAs was lower than predicted, indicating an increased dependence on the horizontal pressure gradient. In contrast, the measured shear stress required to move ellipsoidal SOAs was higher than predicted, even compared to values modified for larger particles in mixed-grain riverine environments. The laboratory observations will be used to improve the prediction of incipient motion, transport, and seafloor interaction of SOAs.

  3. Planet-wide sand motion on mars

    Science.gov (United States)

    Bridges, N.T.; Bourke, M.C.; Geissler, P.E.; Banks, M.E.; Colon, C.; Diniega, S.; Golombek, M.P.; Hansen, C.J.; Mattson, S.; McEwen, A.S.; Mellon, M.T.; Stantzos, N.; Thomson, B.J.

    2012-01-01

    Prior to Mars Reconnaissance Orbiter data, images of Mars showed no direct evidence for dune and ripple motion. This was consistent with climate models and lander measurements indicating that winds of sufficient intensity to mobilize sand were rare in the low-density atmosphere. We show that many sand ripples and dunes across Mars exhibit movement of as much as a few meters per year, demonstrating that Martian sand migrates under current conditions in diverse areas of the planet. Most motion is probably driven by wind gusts that are not resolved in global circulation models. A past climate with a thicker atmosphere is only required to move large ripples that contain coarse grains. ?? 2012 Geological Society of America.

  4. Simulation of aeolian sand saltation with rotational motion

    Science.gov (United States)

    Huang, Ning; Wang, Cong; Pan, Xiying

    2010-11-01

    In this work, we propose a theoretical model based on the distribution functions of initial liftoff velocity and angular velocity of sand grains to describe a sand saltation process in which both wind field-sand grain coupling and the Magnus force experienced by saltating sand grains have been incorporated. The computation results showed that the Magnus force had significant effects on sand grain saltation. In particular, when the Magnus force was incorporated, the calculated sand transport fluxes and sand transport rate per unit width were closer to the experimental value than when this force was excluded. The sand transport flux is enhanced because the Magnus force owing to particle rotation causes the particles to have higher and longer trajectories, so the particles can get more speed and energy from the wind, which leads to a larger sand transport flux. In addition, it was found that when taking the Magnus force into account, the probability density of the impact velocity and angular velocity of saltating sand grains followed an exponential distribution and a unimodal asymmetric distribution, respectively. Moreover, the sand energy flux increased with the height above the sand surface until the energy flux reached its maximum and then decreased. Furthermore, the energy flux near the ground surface decreased as the grain diameter increased, but beyond a specific height the energy flux increased with the grain diameter. Finally, for the same sand grain diameter, the energy flux increased with the friction velocity.

  5. Fine sand in motion: the influence of interstitial air

    NARCIS (Netherlands)

    Homan, T.A.M.

    2013-01-01

    Sand is a granular material, and therefore it consists of individual grains arranged in a packing. The pores in-between the grains are usually filled with a fluid, in this case air. Now, is this interstitial air able to influence the behavior of the sand bed as a whole? When a ball impacts on fine,

  6. Effect of Initial Principal Stress Direction on the Dynamic Characteristics of Carbonate Sand

    Institute of Scientific and Technical Information of China (English)

    Yu Haizhen; Zhao Wenguang; Wang Ren; Li Jianguo; He Yang

    2005-01-01

    The dynamic characteristics of carbonate sand under wave loads are very important for constructions on the ocean floor. The initial principal stress direction has been known to exert some influence on the dynamic characteristics of sand during cyclic loading. In an effort to investigate this aspect of the problem, several series of cyclic undrained tests were carried out on a saturated and loose sample of carbonate sand using a geotechnical static and dynamic universal triaxial shear apparatus. In this test apparatus, a hollow cylindrical sand specimen is subjected to a simultaneous application of both triaxial and torsional modes of shear stresses, which brings about the continuous rotation of principal stress axes. The test results indicated that the initial principal stress direction has a considerable influence on the dynamic strength of loose carbonate sand and with the increase of initial orientation of principal stress, dynamic strength will be reduced, the cyclic pore pressure increased, but the residual pore pressure reduced.

  7. Vertical ground motion and its effects on liquefaction resistance of fully saturated sand deposits.

    Science.gov (United States)

    Tsaparli, Vasiliki; Kontoe, Stavroula; Taborda, David M G; Potts, David M

    2016-08-01

    Soil liquefaction has been extensively investigated over the years with the aim to understand its fundamental mechanism and successfully remediate it. Despite the multi-directional nature of earthquakes, the vertical seismic component is largely neglected, as it is traditionally considered to be of much lower amplitude than the components in the horizontal plane. The 2010-2011 Canterbury earthquake sequence in New Zealand is a prime example that vertical accelerations can be of significant magnitude, with peak amplitudes well exceeding their horizontal counterparts. As research on this topic is very limited, there is an emerging need for a more thorough investigation of the vertical motion and its effect on soil liquefaction. As such, throughout this study, uni- and bidirectional finite-element analyses are carried out focusing on the influence of the input vertical motion on sand liquefaction. The effects of the frequency content of the input motion, of the depth of the deposit and of the hydraulic regime, using variable permeability, are investigated and exhaustively discussed. The results indicate that the usual assumption of linear elastic response when compressional waves propagate in a fully saturated sand deposit does not always hold true. Most importantly post-liquefaction settlements appear to be increased when the vertical component is included in the analysis.

  8. AN ANALYTICAL SOLUTION FOR CALCULATING THE INITIATION OF SEDIMENT MOTION

    Institute of Scientific and Technical Information of China (English)

    Thomas LUCKNER; Ulrich ZANKE

    2007-01-01

    This paper presents an analytical solution for calculating the initiation of sediment motion and the risk of river bed movement. It thus deals with a fundamental problem in sediment transport, for which no complete analytical solution has yet been found. The analytical solution presented here is based on forces acting on a single grain in state of initiation of sediment motion. The previous procedures for calculating the initiation of sediment motion are complemented by an innovative combination of optical surface measurement technology for determining geometrical parameters and their statistical derivation as well as a novel approach for determining the turbulence effects of velocity fluctuations. This two aspects and the comparison of the solution functions presented here with the well known data and functions of different authors mainly differ the presented solution model for calculating the initiation of sediment motion from previous approaches. The defined values of required geometrical parameters are based on hydraulically laboratory tests with spheres. With this limitations the derivated solution functions permit the calculation of the effective critical transport parameters of a single grain, the calculation of averaged critical parameters for describing the state of initiation of sediment motion on the river bed, the calculation of the probability density of the effective critical velocity as well as the calculation of the risk of river bed movement. The main advantage of the presented model is the closed analytical solution from the equilibrium of forces on a single grain to the solution functions describing the initiation of sediment motion.

  9. Experimental research on the mixed sand ratio and initial dry density of weathered sand improved expansive soil free load swelling rate

    Institute of Scientific and Technical Information of China (English)

    Yang Jun; Yang Zhi; Zhang Guodong; Tang Yunwei; Chen Hongping

    2014-01-01

    In this paper, through the indoor free load swelling rate test, expansive soil in a section of a first- class highway reconstruction project in Yichang City was studied. It emphatically analyzed the interrelations among free load swelling rate, non-load time, the proportion of mixed sand and initial dry density. Experimen- tal studies have shown that: Free load swelling deformation is mainly divided into three stages of rapid expan- sion, slow expansion and final stability; when the initial dry density is constant, free load swelling rate of the weathered sand modified soil will reduce rapidly before they slow down with the increase of sand proportion, and weathered sand modified soil free load swelling rate is not sensitive to the large amount of sand mixed; in the same mixed sand ratio, weathered sand modified soil free load swelling rate increases rapidly with the in- crease of initial dry density, there is a good linear correlation between them. To take appropriate control of the initial dry density during the expansive soil subgrade construction helps to reduce its swelling deformation and ensures the stability of the embankment.

  10. Initial spreading of a mega feeder nourishment : Observations of the Sand Engine pilot project

    NARCIS (Netherlands)

    de Schipper, Matthieu A.; de Vries, Sierd; Ruessink, Gerben|info:eu-repo/dai/nl/169093360; de Zeeuw, Roeland C.; Rutten, Jantien; van Gelder-Maas, Carola; Stive, Marcel J F

    2016-01-01

    Sand nourishments are a widely applied technique to increase beach width for recreation or coastal safety. As the size of these nourishments increases, new questions arise on the adaptation of the coastal system after such large unnatural shapes have been implemented. This paper presents the initial

  11. Measurements of coupled fluid and sediment motion over mobile sand dunes in a laboratory flume

    Institute of Scientific and Technical Information of China (English)

    Daniel G.WREN; Roger A.KUHNLE

    2008-01-01

    The relationship between turbulent fluid motions and sediment particle motions over mobile sand dunes was investigated by using a laser Doppler velocimeter and an acoustic backscatter system in laboratory experiments performed at the USDA-ARS-National Sedimentation Laboratory.Profiles of acoustic backscatter from particles and at-a-point turbulence data were collected while translating both measurement devices downstream at the speed of mobile dune bedforms.The resulting data set was used to examine the frequency (recurrence frequency) at which the fluctuating backscatter and fluid velocity signals exceeded magnitude thresholds based on the standard deviation (σ) of the local velocity and the magnitude the acoustic signal resulting from backscatter from suspended particles.The slope of the downstream and vertical velocity recurrence frequencies generally indicated a gradually increasing recurrence time with increasing elevation.The recurrence frequency for acoustic backscatter data was not strongly variable with elevation.The closest correspondence between the recurrence frequencies of sediment backscatter and vertical velocities at the 1σ magnitude threshold was in a region defined by X/L<0.4 and 3<6 cm.The downstream velocity was most closely related to backscatter in a small region at 0.4<X/L<0.8 and less than 3-4 cm from the bed.

  12. 76 FR 9348 - Sand Drag LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for...

    Science.gov (United States)

    2011-02-17

    ... From the Federal Register Online via the Government Publishing Office ] DEPARTMENT OF ENERGY Federal Energy Regulatory Commission Sand Drag LLC; Supplemental Notice That Initial Market-Based Rate...-referenced proceeding of Sand Drag LLC's application for market-based rate authority, with an...

  13. Primer Output and Initial Projectile Motion for 5.56- and 7.62-mm Ammunition

    Science.gov (United States)

    2015-09-01

    ARL-TR-7479 ● SEP 2015 US Army Research Laboratory Primer Output and Initial Projectile Motion for 5.56- and 7.62-mm Ammunition...Output and Initial Projectile Motion for 5.56- and 7.62-mm Ammunition by John J Ritter and Richard A Beyer Weapons and Materials Research...

  14. Initial insights into the age and origin of the Kubuqi sand sea of northern China

    Science.gov (United States)

    Yang, Xiaoping; Forman, Steven; Hu, Fangen; Zhang, Deguo; Liu, Ziting; Li, Hongwei

    2016-04-01

    The Kubuqi Desert is the only active sand sea in the semiarid regions of northern China and occurs along the southern margin of the Yellow River. Little is known about the age and origin of this large (17,000 km2) sand sea with a present annual precipitation of 200-480 mm. Sand drift potentials indicated net capable winds for aeolian transport are from the northwest, though winds are stronger to north beyond the dune field than within the sand sea. Geomorphic and stratigraphic observations indicate that Holocene aeolian sand often drapes over bedrock and river terraces as a palimpsest landscape. Field investigations identified four stratigraphic sections with multiple aeolian sand units and palaeosols, with age control by optically stimulated luminescence (OSL) dating of quartz grains. Palaeosols are weakly developed, mostly accumulative A horizon with organic carbon content farming from lost cities in the Kubuqi Desert during the Han (206 B.C. - A.D. 220) and the Tang (A.D. 608 - 907) Dynasties. Also, variable discharge of the Yellow River with local diversions for irrigation and throughout the catchment resulted in possibly an increased supply of aeolian particles for dune field expansion in the past 2 ka.

  15. The influence of initial resting posture on range of motion of the lumbar spine.

    Science.gov (United States)

    Coates, J E; McGregor, A H; Beith, I D; Hughes, S P

    2001-08-01

    The aim of this study was to investigate the influence of initial resting posture on range of motion of the lumbar spine in 18 normal subjects. Subjects resting posture and active range of motion was measured using the CA-6000 Spinal Motion Analyser (OSI, USA) in five test positions, namely in flat standing and with a variety of heel raises. Analysis showed that there was no significant correlation between subject's normal resting posture and active range of motion. However, when subjects resting posture was artificially altered with heel raises, significant effects on the active range of motion were demonstrated. Increasing heel height significantly influenced resting posture in the sagittal plane only. As heel height increased, the lumbar lordosis decreased and a significant reduction in the range of lumbar spine flexion (Pspine as an examination tool and suggest that studies using range of motion as an outcome measure should consider initial resting posture. Copyright 2001 Harcourt Publishers Ltd.

  16. The initial establishment of the tectonic block motion model of China from space geodetic data

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Using the velocity fields of 28 GPS sites in China and its contiguous area and International Terrestrial Reference Frame ITRF96, an initial tectonic block motion model of China was established. The model was quite consistent with those obtained from the geologic data. The model could show the sketch of China crustal horizontal motion.

  17. SHEAR STRESS FOR INITIATION OF MOTION OF NON-UNIFORM SEDIMENT MIXTURES

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Experiments on initiation of motion of different fractions of non-uniform sediment mixtures are reported. Four sediment mixes and reference transport method to define the threshold of bed particle movement are used in this analysis. Factors controlling the initiation of motion are analyzed. It is found that relative size of different grains with respect to a median size greatly affects the initiation of movement. The incipient motion of non-uniform sediment is very much dependent on the absolute size for coarser fractions.Considering the factors controlling the initiation of motion the experimental data sets along with the other available data yield a new relationship for the calculation of critical shear stress of non-uniform sediments. A set of equations have found that all the data points fall into a single line for the finer and for coarser fractions.

  18. Initial geochemical characteristics of fluid fine tailings in an oil sands end pit lake

    Energy Technology Data Exchange (ETDEWEB)

    Dompierre, Kathryn A. [Department of Civil and Geological Engineering, University of Saskatchewan, Saskatoon, Saskatchewan, Canada S7N 5A9 (Canada); Lindsay, Matthew B.J., E-mail: matt.lindsay@usask.ca [Department of Geological Sciences, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5E2 (Canada); Cruz-Hernández, Pablo [Department of Geology, University of Huelva, Campus ‘El Carmen’, E-21071 Huelva (Spain); Halferdahl, Geoffrey M. [Environmental Research and Development, Syncrude Canada Limited, Edmonton, Alberta T6N 1H4 (Canada)

    2016-06-15

    Geochemical characteristics of fluid fine tailings (FFT) were examined in Base Mine Lake (BML), which is the first full-scale demonstration oil sands end pit lake (EPL) in northern Alberta, Canada. Approximately 186 Mm{sup 3} of FFT was deposited between 1994 and 2012, before BML was established on December 31, 2012. Bulk FFT samples (n = 588) were collected in July and August 2013 at various depths at 15 sampling sites. Temperature, solid content, electrical conductivity (EC), pH, Eh and alkalinity were measured for all samples. Detailed geochemical analyses were performed on a subset of samples (n = 284). Pore-water pH decreased with depth by approximately 0.5 within the upper 10 m of the FFT. Major pore-water constituents included Na (880 ± 96 mg L{sup −1}) and Cl (560 ± 95 mg L{sup −1}); Ca (19 ± 4.1 mg L{sup −1}), Mg (11 ± 2.0 mg L{sup −1}), K (16 ± 2.3 mg L{sup −1}) and NH{sub 3} (9.9 ± 4.7 mg L{sup −1}) were consistently observed. Iron and Mn concentrations were low within FFT pore water, whereas SO{sub 4} concentrations decreased sharply across the FFT–water interface. Geochemical modeling indicated that FeS{sub (s)} precipitation was favoured under SO{sub 4}-reducing conditions. Pore water was also under-saturated with respect to gypsum [CaSO{sub 4}·2H{sub 2}O], and near saturation with respect to calcite [CaCO{sub 3}], dolomite [CaMg(CO{sub 3}){sub 2}] and siderite [FeCO{sub 3}]. X-ray diffraction (XRD) suggested that carbonate-mineral dissolution largely depleted calcite and dolomite. X-ray absorption near edge structure (XANES) spectroscopy revealed the presence of FeS{sub (s)}, pyrite [FeS{sub 2}], and siderite. Carbonate-mineral dissolution and secondary mineral precipitation have likely contributed to FFT dewatering and settlement. However, the long-term importance of these processes within EPLs remains unknown. These results provide a reference for assessing the long-term geochemical evolution of oil sands EPLs, and offer

  19. Initial geochemical characteristics of fluid fine tailings in an oil sands end pit lake.

    Science.gov (United States)

    Dompierre, Kathryn A; Lindsay, Matthew B J; Cruz-Hernández, Pablo; Halferdahl, Geoffrey M

    2016-06-15

    Geochemical characteristics of fluid fine tailings (FFT) were examined in Base Mine Lake (BML), which is the first full-scale demonstration oil sands end pit lake (EPL) in northern Alberta, Canada. Approximately 186Mm(3) of FFT was deposited between 1994 and 2012, before BML was established on December 31, 2012. Bulk FFT samples (n=588) were collected in July and August 2013 at various depths at 15 sampling sites. Temperature, solid content, electrical conductivity (EC), pH, Eh and alkalinity were measured for all samples. Detailed geochemical analyses were performed on a subset of samples (n=284). Pore-water pH decreased with depth by approximately 0.5 within the upper 10m of the FFT. Major pore-water constituents included Na (880±96mgL(-1)) and Cl (560±95mgL(-1)); Ca (19±4.1mgL(-1)), Mg (11±2.0mgL(-1)), K (16±2.3mgL(-1)) and NH3 (9.9±4.7mgL(-1)) were consistently observed. Iron and Mn concentrations were low within FFT pore water, whereas SO4 concentrations decreased sharply across the FFT-water interface. Geochemical modeling indicated that FeS(s) precipitation was favoured under SO4-reducing conditions. Pore water was also under-saturated with respect to gypsum [CaSO4·2H2O], and near saturation with respect to calcite [CaCO3], dolomite [CaMg(CO3)2] and siderite [FeCO3]. X-ray diffraction (XRD) suggested that carbonate-mineral dissolution largely depleted calcite and dolomite. X-ray absorption near edge structure (XANES) spectroscopy revealed the presence of FeS(s), pyrite [FeS2], and siderite. Carbonate-mineral dissolution and secondary mineral precipitation have likely contributed to FFT dewatering and settlement. However, the long-term importance of these processes within EPLs remains unknown. These results provide a reference for assessing the long-term geochemical evolution of oil sands EPLs, and offer insight into the chemistry of pore water released from FFT to the overlying water cover.

  20. ON THE INFLUENCE OF TURBULENCE ON THE INITIATION OF SEDIMENT MOTION

    Institute of Scientific and Technical Information of China (English)

    U.C.E.ZANKE

    2003-01-01

    For the initiation of sediment motion a theory is developed,which presupposes that the critical shear stress τc responsible for inducing motion in non-turbulent flow is solely defined by the angle of internal friction φ or the angle of repose φ' of single grains. In turbulent flow,fluctuations τ' in the shear stress as well as lift forces produced by these fluctuations also occur. Owing to this,the actual (effective) critical shear stress τ + τ' acting on a grain is larger than the average stress τ on the one hand,and on the other hand,the effective weight of the grains is reduced: they become effectively lighter. On the basis of the presented analytical formulation the initiation of sediment motion may be described solely by the angle of repose of the grains and turbulence parameters.

  1. Sand transportation and reverse patterns over leeward face of sand dune

    Science.gov (United States)

    Jiang, Hong; Dun, Hongchao; Tong, Ding; Huang, Ning

    2017-04-01

    Sand saltation has complex interactions with turbulent flow and dune form. Most models of wind-blown sand consider ideal circumstances such as steady wind velocity and a flat surface, and the bulk of data on wind flow and sand transport over an individual dune has focused mostly on the influence of dune shape or inter-dune space on the wind flow, neglecting the effect of morphology on sand saltation, particularly airflow and sand transportation over the leeward slope. Wind flow structures over the leeward slope of sand dunes have a fundamental influence on the organization of sand dunes. In order to understand sand dune dynamics, lee face airflow and sediment transportation should be paid more attention. Previous field observations could not measure turbulent flow structure well because of the limited observation points and the influence of experiment structure on wind field. In addition, the reverse sand particles over leeward face could not be collected by sand trap in field. Numerous field observations could not measure turbulent flow structure because of the limited observation points and the influence of experimental structures on the wind field. In addition, the reverse transport of sand particles over leeward face could not be collected by sand traps in field. Therefore, this paper aims to investigate the turbulent flow structure and sand transport pattern over the leeward slope. A numerical model of sand saltation over slope terrain is constructed, which also considers the coupling effects between air flow and sand particles. The large eddy simulation method is used to model turbulent flow. Sand transport is simulated by tracking the trajectory of each sand particle. The results show that terrain significantly alters the turbulent air flow structure and wind-blown sand movement, especially over the leeward slope. Here, mass flux increases initially and then decreases with height in the reversed flow region in the direction of wind flow, and the mass flux

  2. Cooling the Collective Motion of Trapped Ions to Initialize a Quantum Register

    Science.gov (United States)

    2016-09-13

    VOLUME 81, NUMBER 7 P H Y S I C A L R E V I E W L E T T E R S 17 AUGUST 1998Cooling the Collective Motion of Trapped Ions to Initialize a Quantum ...modes of motion of two trapped 9Be1 ions. This is a crucial step towards realizing quantum logic gates which can entangle the ions’ internal...suggesting the importance of these modes in future experiments. [S0031-9007(98)06838-0] PACS numbers: 03.67.Lx, 03.65.–w, 32.80.PjIn physics, quantum

  3. Motion

    CERN Document Server

    Graybill, George

    2007-01-01

    Take the mystery out of motion. Our resource gives you everything you need to teach young scientists about motion. Students will learn about linear, accelerating, rotating and oscillating motion, and how these relate to everyday life - and even the solar system. Measuring and graphing motion is easy, and the concepts of speed, velocity and acceleration are clearly explained. Reading passages, comprehension questions, color mini posters and lots of hands-on activities all help teach and reinforce key concepts. Vocabulary and language are simplified in our resource to make them accessible to str

  4. Initial assessment of facial nerve paralysis based on motion analysis using an optical flow method.

    Science.gov (United States)

    Samsudin, Wan Syahirah W; Sundaraj, Kenneth; Ahmad, Amirozi; Salleh, Hasriah

    2016-01-01

    An initial assessment method that can classify as well as categorize the severity of paralysis into one of six levels according to the House-Brackmann (HB) system based on facial landmarks motion using an Optical Flow (OF) algorithm is proposed. The desired landmarks were obtained from the video recordings of 5 normal and 3 Bell's Palsy subjects and tracked using the Kanade-Lucas-Tomasi (KLT) method. A new scoring system based on the motion analysis using area measurement is proposed. This scoring system uses the individual scores from the facial exercises and grades the paralysis based on the HB system. The proposed method has obtained promising results and may play a pivotal role towards improved rehabilitation programs for patients.

  5. Initiation of a Database of CEUS Ground Motions for NGA East

    Science.gov (United States)

    Cramer, C. H.

    2007-12-01

    The Nuclear Regulatory Commission has funded the first stage of development of a database of central and eastern US (CEUS) broadband and accelerograph records, along the lines of the existing Next Generation Attenuation (NGA) database for active tectonic areas. This database will form the foundation of an NGA East project for the development of CEUS ground-motion prediction equations that include the effects of soils. This initial effort covers the development of a database design and the beginning of data collection to populate the database. It also includes some processing for important source parameters (Brune corner frequency and stress drop) and site parameters (kappa, Vs30). Besides collecting appropriate earthquake recordings and information, existing information about site conditions at recording sites will also be gathered, including geology and geotechnical information. The long-range goal of the database development is to complete the database and make it available in 2010. The database design is centered on CEUS ground motion information needs but is built on the Pacific Earthquake Engineering Research Center's (PEER) NGA experience. Documentation from the PEER NGA website was reviewed and relevant fields incorporated into the CEUS database design. CEUS database tables include ones for earthquake, station, component, record, and references. As was done for NGA, a CEUS ground- motion flat file of key information will be extracted from the CEUS database for use in attenuation relation development. A short report on the CEUS database and several initial design-definition files are available at https://umdrive.memphis.edu:443/xythoswfs/webui/_xy-7843974_docstore1. Comments and suggestions on the database design can be sent to the author. More details will be presented in a poster at the meeting.

  6. On using the dynamic snap-through motion of MEMS initially curved microbeams for filtering applications

    KAUST Repository

    Ouakad, Hassen M.

    2014-01-01

    Numerical and experimental investigations of the dynamics of micromachined shallow arches (initially curved microbeams) and the possibility of using their dynamic snap-through motion for filtering purposes are presented. The considered MEMS arches are actuated by a DC electrostatic load along with an AC harmonic load. Their dynamics is examined numerically using a Galerkin-based reduced-order model when excited near both their first and third natural frequencies. Several simulation results are presented demonstrating interesting jumps and dynamic snap-through behavior of the MEMS arches and their attractive features for uses as band-pass filters, such as their sharp roll-off from pass-bands to stop-bands and their flat response. Experimental work is conducted to test arches realized of curved polysilicon microbeams when excited by DC and AC loads. Experimental data of the micromachined curved beams are shown for the softening and hardening behavior near the first and third natural frequencies, respectively, as well as dynamic snap-through motion. © 2013 Elsevier Ltd.

  7. Fontainebleau Sand

    DEFF Research Database (Denmark)

    Leth, Caspar Thrane

    2006-01-01

    The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand.......The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand....

  8. Cenozoic vertical motions in the Moray Firth Basin associated with initiation of the Iceland Plume

    Science.gov (United States)

    Mackay, L. M.; Turner, J.; Jones, S. M.; White, N. J.

    2005-10-01

    It is likely that the Iceland mantle plume generated transient uplift across the North Atlantic region when it initiated in earliest Cenozoic time. However, transient uplift recorded in sedimentary basins fringing the region can be overprinted by the effects of permanent uplift. Identifying and quantifying transient uplift can only be achieved in areas which have a well-constrained stratigraphic record and across which the relative importance of permanent and transient uplift varies (e.g., the Moray Firth Basin, North Sea). By analyzing the subsidence of 50 boreholes from the Moray Firth Basin (MFB), residual vertical motions unrelated to rifting have been isolated. Transient uplift of 180-425 m occurred during Paleocene times. The western MFB has also been affected by permanent Cenozoic uplift, with denudation decreasing from 1.3 ± 0.1 km in the west of the basin to zero denudation east of 1°W. Dynamic support above the Iceland Plume led to transient uplift of the entire MFB in early Paleocene times, peaking in latest Paleocene times. In early Eocene times the effect of the plume waned, and subsidence occurred. Paleocene permanent uplift of the NW British Isles is generally accepted to have been due to magmatic underplating of the crust emplaced during the British Tertiary Igneous Province (61-58.5 Ma). The cause of Neogene uplift events is poorly understood, but it could also be associated with the Iceland Plume.

  9. Compressive behavior of fine sand.

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Bradley E. (Air Force Research Laboratory, Eglin, FL); Kabir, Md. E. (Purdue University, West Lafayette, IN); Song, Bo; Chen, Wayne (Purdue University, West Lafayette, IN)

    2010-04-01

    The compressive mechanical response of fine sand is experimentally investigated. The strain rate, initial density, stress state, and moisture level are systematically varied. A Kolsky bar was modified to obtain uniaxial and triaxial compressive response at high strain rates. A controlled loading pulse allows the specimen to acquire stress equilibrium and constant strain-rates. The results show that the compressive response of the fine sand is not sensitive to strain rate under the loading conditions in this study, but significantly dependent on the moisture content, initial density and lateral confinement. Partially saturated sand is more compliant than dry sand. Similar trends were reported in the quasi-static regime for experiments conducted at comparable specimen conditions. The sand becomes stiffer as initial density and/or confinement pressure increases. The sand particle size become smaller after hydrostatic pressure and further smaller after dynamic axial loading.

  10. Triaxial tests in Fontainebleau sand

    DEFF Research Database (Denmark)

    Latini, Chiara; Zania, Varvara

    2016-01-01

    The purpose of this internal report is to examine the influence of relative density on the strength and deformation characteristics of Fontainebleau sand. Compression triaxial tests were performed on saturated sand samples with different densities and initial confining pressure. Note that the tes......The purpose of this internal report is to examine the influence of relative density on the strength and deformation characteristics of Fontainebleau sand. Compression triaxial tests were performed on saturated sand samples with different densities and initial confining pressure. Note...... that the testing procedure and the data processing were carried out according to the specifications of ETCS-F1.97....

  11. Calculation of correlated initial state in the hierarchical equations of motion method using an imaginary time path integral approach.

    Science.gov (United States)

    Song, Linze; Shi, Qiang

    2015-11-21

    Based on recent findings in the hierarchical equations of motion (HEOM) for correlated initial state [Y. Tanimura, J. Chem. Phys. 141, 044114 (2014)], we propose a new stochastic method to obtain the initial conditions for the real time HEOM propagation, which can be used further to calculate the equilibrium correlation functions and symmetrized correlation functions. The new method is derived through stochastic unraveling of the imaginary time influence functional, where a set of stochastic imaginary time HEOM are obtained. The validity of the new method is demonstrated using numerical examples including the spin-Boson model, and the Holstein model with undamped harmonic oscillator modes.

  12. Parameterization of Finite-Element Cryo-Hydrologic Sand Dune Model to Constrain Debris-Flow-Initiating Subsurface Temperatures and Pore-Water Pressures, Great Kobuk Sand Dunes, Alaska

    Science.gov (United States)

    Dinwiddie, C. L.; Hooper, D. M.

    2015-05-01

    To explain how debris flows form at subfreezing air temperatures, we present meteorology-driven, numerical simulation-derived subsurface temperature and pore-water pressure profiles in the Great Kobuk Sand Dunes of Alaska, for incipient flow events.

  13. Information fusion performance evaluation for motion imagery data using mutual information: initial study

    Science.gov (United States)

    Grieggs, Samuel M.; McLaughlin, Michael J.; Ezekiel, Soundararajan; Blasch, Erik

    2015-06-01

    As technology and internet use grows at an exponential rate, video and imagery data is becoming increasingly important. Various techniques such as Wide Area Motion imagery (WAMI), Full Motion Video (FMV), and Hyperspectral Imaging (HSI) are used to collect motion data and extract relevant information. Detecting and identifying a particular object in imagery data is an important step in understanding visual imagery, such as content-based image retrieval (CBIR). Imagery data is segmented and automatically analyzed and stored in dynamic and robust database. In our system, we seek utilize image fusion methods which require quality metrics. Many Image Fusion (IF) algorithms have been proposed based on different, but only a few metrics, used to evaluate the performance of these algorithms. In this paper, we seek a robust, objective metric to evaluate the performance of IF algorithms which compares the outcome of a given algorithm to ground truth and reports several types of errors. Given the ground truth of a motion imagery data, it will compute detection failure, false alarm, precision and recall metrics, background and foreground regions statistics, as well as split and merge of foreground regions. Using the Structural Similarity Index (SSIM), Mutual Information (MI), and entropy metrics; experimental results demonstrate the effectiveness of the proposed methodology for object detection, activity exploitation, and CBIR.

  14. Motion-Corrected Real-Time Cine Magnetic Resonance Imaging of the Heart: Initial Clinical Experience.

    Science.gov (United States)

    Rahsepar, Amir Ali; Saybasili, Haris; Ghasemiesfe, Ahmadreza; Dolan, Ryan S; Shehata, Monda L; Botelho, Marcos P; Markl, Michael; Spottiswoode, Bruce; Collins, Jeremy D; Carr, James C

    2017-08-29

    Free-breathing real-time (RT) imaging can be used in patients with difficulty in breath-holding; however, RT cine imaging typically experiences poor image quality compared with segmented cine imaging because of low resolution. Here, we validate a novel unsupervised motion-corrected (MOCO) reconstruction technique for free-breathing RT cardiac images, called MOCO-RT. Motion-corrected RT uses elastic image registration to generate a single heartbeat of high-quality data from a free-breathing RT acquisition. Segmented balanced steady-state free precession (bSSFP) cine images and free-breathing RT images (Cartesian, TGRAPPA factor 4) were acquired with the same spatial/temporal resolution in 40 patients using clinical 1.5 T magnetic resonance scanners. The respiratory cycle was estimated using the reconstructed RT images, and nonrigid unsupervised motion correction was applied to eliminate breathing motion. Conventional segmented RT and MOCO-RT single-heartbeat cine images were analyzed to evaluate left ventricular (LV) function and volume measurements. Two radiologists scored images for overall image quality, artifact, noise, and wall motion abnormalities. Intraclass correlation coefficient was used to assess the reliability of MOCO-RT measurement. Intraclass correlation coefficient showed excellent reliability (intraclass correlation coefficient ≥ 0.95) of MOCO-RT with segmented cine in measuring LV function, mass, and volume. Comparison of the qualitative ratings indicated comparable image quality for MOCO-RT (4.80 ± 0.35) with segmented cine (4.45 ± 0.88, P = 0.215) and significantly higher than conventional RT techniques (3.51 ± 0.41, P cine (1.51 ± 0.90, P = 0.088 and 1.23 ± 0.45, P = 0.182) were not different. Wall motion abnormality ratings were comparable among different techniques (P = 0.96). The MOCO-RT technique can be used to process conventional free-breathing RT cine images and provides comparable quantitative assessment of LV function and volume

  15. Moving sand dunes

    CERN Document Server

    Sparavigna, Amelia Carolina

    2011-01-01

    In several desert areas, the slow motion of sand dunes can be a challenge for modern human activities and a threat for the survival of ancient places or archaeological sites. However, several methods exist for surveying the dune fields and estimate their migration rate. Among these methods, the use of satellite images, in particular of those freely available on the World Wide Web, is a convenient resource for the planning of future human settlements and activities.

  16. Zero initial partial derivatives of satellite orbits with respect to force parameters violate the physics of motion of celestial bodies

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Satellite orbits have been routinely used to produce models of the Earth’s gravity field. In connection with such productions, the partial derivatives of a satellite orbit with respect to the force parameters to be determined, namely, the unknown harmonic coefficients of the gravitational model, have been first computed by setting the initial values of partial derivatives to zero. In this note, we first design some simple mathematical examples to show that setting the initial values of partial derivatives to zero is generally erroneous mathematically. We then prove that it is prohibited physically. In other words, set-ting the initial values of partial derivatives to zero violates the physics of motion of celestial bodies.

  17. Zero initial partial derivatives of satellite orbits with respect to force parameters violate the physics of motion of celestial bodies

    Institute of Scientific and Technical Information of China (English)

    XU PeiLiang

    2009-01-01

    Satellite orbits have been routinely used to produce models of the Earth's gravity field. In connection with such productions, the partial derivatives of a satellite orbit with respect to the force parameters to be determined, namely, the unknown harmonic coefficients of the gravitational model, have been first computed by setting the initial values of partial derivatives to zero. In this note, we first design some simple mathematical examples to show that setting the initial values of partial derivatives to zero is generally erroneous mathematically. We then prove that it is prohibited physically. In other words, set-ting the initial values of partial derivatives to zero violates the physics of motion of celestial bodies.

  18. Disturbance of the inclined inserting-type sand fence to wind-sand flow fields and its sand control characteristics

    Science.gov (United States)

    Cheng, Jian-jun; Lei, Jia-qiang; Li, Sheng-yu; Wang, Hai-feng

    2016-06-01

    The inclined inserting-type sand fence is a novel sand retaining wall adopted along the Lanxin High-Speed Railway II in Xinjiang for controlling and blocking sand movement. To verify the effectiveness of the new fence structure for sand prevention, a wind tunnel test was used for flow field test simulation of the sand fence. The results indicate that the inclined inserting-type sand fence was able to deflect the flow of the sand and was able to easily form an upward slant acceleration zone on the leeward side of the sand fence. As shown by the percentage change in sand collection rates on the windward side and the leeward side of the sand fence, the sand flux per unit area at 4 m height in the slant upward direction increased on the leeward side of the inclined inserting-type sand fence. By comparing the flow fields, this site is an acceleration zone, which also reaffirms the correspondence of wind-sand flow fields with the spatial distribution characteristic of the wind-carried sand motion. The field sand collection data indicates that under the effects of the inclined inserting-type sand fence, the sandy air currents passing in front and behind the sand fence not only changed in quality, but the grain composition and particle size also significantly changed, suggesting that the inclined inserting-type sand fence has a sorting and filtering effect on the sandy air currents that passed through. The fence retained coarse particulates on the windward side and fine particulates within the shade of the wind on the leeward side.

  19. A tropical cyclone dynamic initialization technique using high temporal and spatial density atmospheric motion vectors and airborne field campaign data

    Science.gov (United States)

    Hendricks, E. A.; Bell, M. M.; Elsberry, R. L.; Velden, C.

    2016-12-01

    A new tropical cyclone dynamic initialization technique is described and tested. The technique uses the triple-nested Coupled Ocean-Atmosphere Mesoscale Prediction System-Tropical Cyclones (COAMPS-TC) (with horizontal grid spacings of 45-,15-, and 5-km, respectively) in conjunction with the Spline Analysis at Mesoscale Utilizing Radar and Aircraft Instrumentation (SAMURAI). A proof-of-concept demonstration of this technique is given for Hurricane Joaquin from the Office of Naval Research (ONR) Tropical Cyclone Intensity (TCI) field program conducted in 2015. High spatial and temporal resolution atmospheric motion vectors (AMVs), dropwindsondes from the Yankee Environmental Systems High Definition Sounding System (HDSS), and surface wind speed retrievals from the Hurricane Imaging Radiometer (HIRAD) are ingested into SAMURAI to produce increments, which are then used by the COAMPS-TC dynamic initialization scheme to produce consistent dynamic and thermodynamically balanced fields. This high temporal resolution (order of 10-15 minutes) incremental dynamic initialization procedure has advantages over conventional methods in that a bogus vortex is not used, and existing asymmetries (including convective heating and upper and low level wind asymmetries) that exist in the TC are retained. The use of dynamic initialization also ensures improved vortex and environment balance, and consistency with the model physics. A preliminary verification of this new TC initialization scheme will be presented for the initialization and forecast of Hurricane Joaquin (2015).

  20. 3D motion and strain estimation of the heart: initial clinical findings

    Science.gov (United States)

    Barbosa, Daniel; Hristova, Krassimira; Loeckx, Dirk; Rademakers, Frank; Claus, Piet; D'hooge, Jan

    2010-03-01

    The quantitative assessment of regional myocardial function remains an important goal in clinical cardiology. As such, tissue Doppler imaging and speckle tracking based methods have been introduced to estimate local myocardial strain. Recently, volumetric ultrasound has become more readily available, allowing therefore the 3D estimation of motion and myocardial deformation. Our lab has previously presented a method based on spatio-temporal elastic registration of ultrasound volumes to estimate myocardial motion and deformation in 3D, overcoming the spatial limitations of the existing methods. This method was optimized on simulated data sets in previous work and is currently tested in a clinical setting. In this manuscript, 10 healthy volunteers, 10 patient with myocardial infarction and 10 patients with arterial hypertension were included. The cardiac strain values extracted with the proposed method were compared with the ones estimated with 1D tissue Doppler imaging and 2D speckle tracking in all patient groups. Although the absolute values of the 3D strain components assessed by this new methodology were not identical to the reference methods, the relationship between the different patient groups was similar.

  1. An integral test on time dependent local extinction for super-coalescing Brownian motion with Lebesgue initial measure

    CERN Document Server

    He, Hui; Zhou, Xiaowen

    2009-01-01

    This paper concerns the almost sure time dependent local extinction behavior for super-coalescing Brownian motion $X$ with $(1+\\beta)$-stable branching and Lebesgue initial measure on $\\bR$. We first give a representation of $X$ using excursions of a continuous state branching process and Arratia's coalescing Brownian flow. For any nonnegative, nondecreasing and right continuous function $g$, put \\tau:=\\sup \\{t\\geq 0: X_t([-g(t),g(t)])>0 \\}. We prove that $\\bP\\{\\tau=\\infty\\}=0$ or 1 according as the integral $\\int_1^\\infty g(t)t^{-1-1/\\beta} dt$ is finite or infinite.

  2. TURBULENT COHERENT STRUCTURES IN CHANNELS WITH SAND WAVES

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Sand wave bed is one of the typical shape of complicated boundaries in hydraulics and river dynamics, and sand wave motion is the main form of the bed load motion in-rivers, thence the study of turbulent structures over sand waves is of importance both in theory and practice. In this paper turbulent coherent structures over single-and multi-sand waves were studied experimentally, the formulae for the separation length and vortex shedding period of the turbulent flow over single-sand wave were suggested, and the characteristics of turbulent coherent structures over multi-sand waves were also given.

  3. Initial operation of a newly developed multichord motional Stark effect diagnostic in KSTAR

    Science.gov (United States)

    Chung, J.; Ko, J.; Wi, H.; Messmer, M.; Schenkelaars, S.; Scheffer, M.; Jaspers, R. J. E.

    2016-11-01

    A photo-elastic modulator based 25-chord motional Stark effect (MSE) diagnostic has been successfully developed and commissioned in Korea Superconducting Tokamak Advanced Research. The diagnostic measures the radial magnetic pitch angle profile of the Stark splitting of a D-alpha line at 656.1 nm by the electric field associated with the neutral deuterium heating beam. A tangential view of the neutral beam provides a good spatial resolution of 1-3 cm for covering the major radius from 1.74 m to 2.28 m, and the time resolution is achieved at 10 ms. An in-vessel calibration before the vacuum closing as well as an in situ calibration during the tokamak operation was performed by means of specially designed polarized lighting sources. In this work, we present the final design of the installed MSE diagnostic and the first results of the commissioning.

  4. Drag-free Spacecraft Technologies: criticalities in the initialization of geodesic motion

    CERN Document Server

    Zanoni, Carlo

    2016-01-01

    Present and future space missions rely on systems of increasingly demanding performance for being successful. Drag-free technology is one of the technologies that is fundamental for LISA-Pathfinder, an ESA mission whose launch is planned for the end of September 2015. A purely drag-free object is defined by the absence of all external forces other than gravity. This is not a natural condition and thus requires a proper design of a spacecraft, whose core is an object in free-fall, called test mass (TM). The purity of the drag-free orbit depends on the spacecraft capability of protecting the TM from disturbances, which indeed has limitations. According to a NASA study, such a concept provides substantial economies for LEO satellites. At the same time, a drag-free motion is required in many missions of fundamental physics. eLISA is an ESA concept mission aimed at opening a new window to the universe, black holes, and massive binary systems by means of gravitational waves. LISA-Pathfinder is in charge of proving ...

  5. Quantitative Measurement of Cerebral Perfusion with Intravoxel Incoherent Motion in Acute Ischemia Stroke: Initial Clinical Experience

    Institute of Scientific and Technical Information of China (English)

    Li-Bao Hu; Nan Hong; Wen-Zhen Zhu

    2015-01-01

    Background:Intravoxel incoherent motion (IVIM) has the potential to provide both diffusion and perfusion information without an exogenous contrast agent,its application for the brain is promising,however,feasibility studies on this are relatively scarce.The aim of this study is to assess the feasibility of IVIM perfusion in patients with acute ischemic stroke (AIS).Methods:Patients with suspected AIS were examined by magnetic resonance imaging within 24 h of symptom onset.Fifteen patients (mean age was 68.7 ± 8.0 years) who underwent arterial spin labeling (ASL) and diffusion-weighted imaging (DWI) were identified as having AIS with ischemic penumbra were enrolled,where ischemic penumbra referred to the mismatch areas of ASL and DWI.Eleven different b-values were applied in the biexponential model.Regions of interest were selected in ischemic penumbras and contralateral normal brain regions.Fast apparent diffusion coefficients (ADCs) and ASL cerebral blood flow (CBF) were measured.The paired t-test was applied to compare ASL CBF,fast ADC,and slow ADC measurements between ischemic penumbras and contralateral normal brain regions.Linear regression and Pearson's correlation were used to evaluate the correlations among quantitative results.Results:The fast ADCs and ASL CBFs of ischemic penumbras were significantly lower than those of the contralateral normal brain regions (1.93 ± 0.78 μm2/ms vs.3.97 ± 2.49 μm2/ms,P =0.007;13.5 ± 4.5 ml· 100 g-1 ·min-1 vs.29.1 ± 12.7 ml·100 g-1 ·min-1,P < 0.001,respectively).No significant difference was observed in slow ADCs between ischemic penumbras and contralateral normal brain regions (0.203 ± 0.090 μm2/ms vs.0.198 ± 0.100 μm2/ms,P =0.451).Compared with contralateral normal brain regions,both CBFs and fast ADCs decreased in ischemic penumbras while slow ADCs remained the same.A significant correlation was detected between fast ADCs and ASL CBFs (r =0.416,P < 0.05).No statistically significant correlation was

  6. A Simple and High Performing Rate Control Initialization Method for H.264 AVC Coding Based on Motion Vector Map and Spatial Complexity at Low Bitrate

    Directory of Open Access Journals (Sweden)

    Yalin Wu

    2014-01-01

    Full Text Available The temporal complexity of video sequences can be characterized by motion vector map which consists of motion vectors of each macroblock (MB. In order to obtain the optimal initial QP (quantization parameter for the various video sequences which have different spatial and temporal complexities, this paper proposes a simple and high performance initial QP determining method based on motion vector map and temporal complexity to decide an initial QP in given target bit rate. The proposed algorithm produces the reconstructed video sequences with outstanding and stable quality. For any video sequences, the initial QP can be easily determined from matrices by target bit rate and mapped spatial complexity using proposed mapping method. Experimental results show that the proposed algorithm can show more outstanding objective and subjective performance than other conventional determining methods.

  7. Initial generation of sand across climate zones of the Mojave, Sierra Nevada, and Klamath Batholiths in California, U.S.A.

    Science.gov (United States)

    Hessler, Angela M.; Lowe, Donald R.

    2017-03-01

    The generation of modern, plutoniclastic sediment across California varies with climate, resulting in significant mineralogical and geochemical differences between parent rock, weathering profile material, and low-order stream sand. With average precipitation of 15 cm/yr in the arid zones and 120 cm/yr in the temperate zones, feldspar is relatively decreased in stream sand (compared to parent rock) by paleoclimate studies, where a moderate precipitation shift is capable of producing a significant loss of feldspar. The differential response of common minerals to chemical weathering should be considered for studies and modeling related to bedrock erodibility, sediment supply, and landscape evolution.

  8. In-motion initial alignment and positioning with INS/CNS/ODO integrated navigation system for lunar rovers

    Science.gov (United States)

    Lu, Jiazhen; Lei, Chaohua; Yang, Yanqiang; Liu, Ming

    2017-06-01

    Many countries have been paying great attention to space exploration, especially about the Moon and the Mars. Autonomous and high-accuracy navigation systems are needed for probers and rovers to accomplish missions. Inertial navigation system (INS)/celestial navigation system (CNS) based navigation system has been used widely on the lunar rovers. Initialization is a particularly important step for navigation. This paper presents an in-motion alignment and positioning method for lunar rovers by INS/CNS/odometer integrated navigation. The method can estimate not only the position and attitude errors, but also the biases of the accelerometers and gyros using the standard Kalman filter. The differences between the platform star azimuth, elevation angles and the computed star azimuth, elevation angles, and the difference between the velocity measured by odometer and the velocity measured by inertial sensors are taken as measurements. The semi-physical experiments are implemented to demonstrate that the position error can reduce to 10 m and attitude error is within 2″ during 5 min. The experiment results prove that it is an effective and attractive initialization approach for lunar rovers.

  9. Sands styrke

    DEFF Research Database (Denmark)

    Jacobsen, H. Moust; Jørgensen, Mogens B.; Poulsen, H. Serup

    1975-01-01

    På grundlag af triaxialforsøg med D=7 og 20 cm og varierende højde på løse og faste lejringer af Blokhussand kan effekten af varierende højde-breddeforhold og spændingsniveau samt skalaeffekten bestemmes. Ved sammenligning med pladeforsøg med overfladelast op til 8 t/m2 kan den almindelige fremga...... fremgangsmåde ved bæreevneberegninger på sand undersøges....

  10. Atmospheric Motion Vectors from INSAT-3D: Initial quality assessment and its impact on track forecast of cyclonic storm NANAUK

    Science.gov (United States)

    Deb, S. K.; Kishtawal, C. M.; Kumar, Prashant; Kiran Kumar, A. S.; Pal, P. K.; Kaushik, Nitesh; Sangar, Ghansham

    2016-03-01

    The advanced Indian meteorological geostationary satellite INSAT-3D was launched on 26 July 2013 with an improved imager and an infrared sounder and is placed at 82°E over the Indian Ocean region. With the advancement in retrieval techniques of different atmospheric parameters and with improved imager data have enhanced the scope for better understanding of the different tropical atmospheric processes over this region. The retrieval techniques and accuracy of one such parameter, Atmospheric Motion Vectors (AMV) has improved significantly with the availability of improved spatial resolution data along with more options of spectral channels in the INSAT-3D imager. The present work is mainly focused on providing brief descriptions of INSAT-3D data and AMV derivation processes using these data. It also discussed the initial quality assessment of INSAT-3D AMVs for a period of six months starting from 01 February 2014 to 31 July 2014 with other independent observations: i) Meteosat-7 AMVs available over this region, ii) in-situ radiosonde wind measurements, iii) cloud tracked winds from Multi-angle Imaging Spectro-Radiometer (MISR) and iv) numerical model analysis. It is observed from this study that the qualities of newly derived INSAT-3D AMVs are comparable with existing two versions of Meteosat-7 AMVs over this region. To demonstrate its initial application, INSAT-3D AMVs are assimilated in the Weather Research and Forecasting (WRF) model and it is found that the assimilation of newly derived AMVs has helped in reduction of track forecast errors of the recent cyclonic storm NANAUK over the Arabian Sea. Though, the present study is limited to its application to one case study, however, it will provide some guidance to the operational agencies for implementation of this new AMV dataset for future applications in the Numerical Weather Prediction (NWP) over the south Asia region.

  11. Tar sand

    Energy Technology Data Exchange (ETDEWEB)

    McLendon, T.R.; Bartke, T.C.

    1990-01-01

    Research on tar sand is briefly discussed. The research program supported by the US Department of Energy (DOE) includes a variety of surface extraction schemes. The University of Utah has process development units (PDU) employing fluidized bed, hot, water-assisted, and fluidized-bed/heat-pipe, coupled combustor technology. Considerable process variable test data have been gathered on these systems: (1) a rotary kiln unit has been built recently; (2) solvent extraction processing is being examined; and (3) an advanced hydrogenation upgrading scheme (hydropyrolysis) has been developed. The University of Arkansas, in collaboration with Diversified Petroleum, Inc., has been working on a fatty acid, solvent extraction process. Oleic acid is the solvent/surfactant. Solvent is recovered by adjusting processing fluid concentrations to separate without expensive operations. Western Research Institute has a PDU-scale scheme called the Recycle Oil Pyrolysis and Extraction (ROPE) process, which combines solvent (hot recycle bitumen) and pyrolytic extraction. 14 refs., 19 figs.

  12. It's in the sand

    OpenAIRE

    Mitchell, Clive

    2016-01-01

    Sand is sand isn’t it? Sand gets everywhere but rather than a nuisance it is a valuable, high-purity raw material. Clive Mitchell, Industrial Minerals Specialist at the British Geological Survey (BGS), talks us through what sand is, what it can be used for and how to find it. His exploration of sand takes us from the deserts of Arabia to the damp sand pits of Mansfield!

  13. Mars Rover Curiosity Traverses of Sand Ripples

    Science.gov (United States)

    Stein, N.; Arvidson, R. E.; Zhou, F.; Heverly, M.; Maimone, M.; Hartman, F.; Bellutta, P.; Iagnemma, K.; Senatore, C.

    2014-12-01

    Martian sand ripples present a challenge for rover mobility, with drives over ripples often characterized by high wheel sinkage and slippage that can lead to incipient embedding. Since landing in Gale Crater, Curiosity has traversed multiple sand ripples, including the transverse aeolian ridge (TAR) straddling Dingo Gap on sols 533 and 535. On sol 672, Curiosity crossed backward over a series of sand ripples before ending its drive after high motor currents initiated visual odometry (VO) processing, which detected 77% slip, well in excess of the imposed 60% slip limit. At the end of the drive, the right front wheel was deeply embedded at the base of a ripple flank with >20 cm sinkage and the rear wheels were near a ripple crest. As Curiosity continues its approach to Mount Sharp it will have to cross multiple ripples, and thus it is important to understand Curiosity's performance on sol 672 and over similar ripples. To this end the sol 672 drive was simulated in ARTEMIS (Adams-Based Rover Terramechanics Interaction Simulator), a software tool consisting of realistic rover mechanical models, a wheel-terrain interaction module for deformable and non-deformable surfaces, and realistic terrain models. ARTEMIS results, Dumont Dunes tests performed in the Mojave Desert using the Scarecrow test rover, and single wheel tests performed at MIT indicate that the high slip encountered on sol 672 likely occurred due to a combination of rover attack angle, ripple geometry, and soil properties. When ripple wavelength approaches vehicle length, the rover can reach orientations in which the leading wheels carry minimal normal loads and the trailing wheels sink deeply, resulting in high slippage and insufficient thrust to propel the rover over ripples. Even on relatively benign (i.e. low tilt) terrains, local morphology can impose high sinkage, thus impeding rover motion. Work is underway to quantify Curiosity's drive performance over various ripple geometries to retrieve soil

  14. Anthropogenic initiation and acceleration of aeolian dune activity within the northern European Sand Belt and societal feedbacks over the last 2500 yrs

    Science.gov (United States)

    Lungershausen, Uta; Larsen, Annegret; Bork, Hans-Rudolf; Duttmann, Rainer

    2017-04-01

    In North-Western Europe, Pleistocene sand sheets have been re-activated during phases of Holocene deforestation and agricultural land-use. Although there are temporal overlaps between anthropogenic activity and sand sheet re-activation, the root cause and subsequent feedbacks between aeolian activity and societal response remain largely unknown. Here, we seek to establish cause and effect by examining the detailed co-variation in both the timing and magnitude of aeolian and anthropogenic activity through the quantification of Holocene dune sediments in combination with archaeological and pollen records. These records indicate a series of complex phases of aeolian activity followed by landscape stabilization, which we attribute primarily to changing patterns of human impact. We find that a steady increase in dune deposition rates in the Medieval Period corresponds to an increase in settlement activity and deforestation ( 1000-1500 AD). At their peak, Medieval deposition rates were 3.4-times larger than during the late Pleistocene, which was the period experiencing the most favourable natural conditions for aeolian sediment transport in the past 11600 years. Prior to the Medieval Period, relative land-surface stability (depositional hiatus) persisted from the late Pleistocene until the Roman Iron Age Period (0-400 AD), in which deforestation to fuel iron production had a minor impact on aeolian activity, as indicated by the lowest recorded deposition rate (0.12 t/ha/a ± 0.02 t/ha/a). Following the Medieval Period peak in aeolian deposition rates, aeolian activity diminishes rapidly, and coincides with the abandonment of nearby human settlement. This can be interpreted as a direct positive feedback in which Medieval agricultural overexploitation crossed sufficient aeolian activity thresholds to render the landscape practically unworkable for cropping agriculture. Based on our findings and a comprehensive review of Northern European sand belt activity, we interpret a

  15. Industrial sand and gravel

    Science.gov (United States)

    Dolley, T.P.

    2013-01-01

    Domestic production of industrial sand and gravel in 2012 was about 49.5 Mt (55 million st), increasing 13 percent compared with that of 2011. Some important end uses for industrial sand and gravel include abrasives, filtration, foundry, glassmaking, hydraulic fracturing sand (frac sand) and silicon metal applications.

  16. The development and initial evaluation of a realistic simulated SPECT dataset with simultaneous respiratory and cardiac motion for gated myocardial perfusion SPECT.

    Science.gov (United States)

    Lee, Taek-Soo; Tsui, Benjamin M W

    2015-02-21

    We developed a realistic simulation dataset for simultaneous respiratory and cardiac (R&C) gated SPECT/CT using the 4D NURBS-based Cardiac-Torso (NCAT) Phantom and Monte Carlo simulation methods, and evaluated it for a sample application study. The 4D NCAT phantom included realistic respiratory motion and beating heart motion based on respiratory gated CT and cardiac tagged MRI data of normal human subjects. To model the respiratory motion, a set of 24 separate 3D NCAT phantoms excluding the heart was generated over a respiratory cycle. The beating heart motion was modeled separately with 48 frames per cardiac cycle for each of the 24 respiratory phases. The resultant set of 24  ×  48 3D NCAT phantoms provides a realistic model of a normal human subject at different phases of combined R&C motions. An almost noise-free SPECT projection dataset for each of the 1152 3D NCAT phantoms was generated using Monte Carlo simulation techniques and the radioactivity uptake distribution of (99m)Tc sestamibi in different organs. By grouping and summing the separate projection datasets, separate or simultaneous R&C gated acquired data with different gating schemes could be simulated. In the initial evaluation, we combined the projection datasets into ungated, 6 respiratory-gates only, 8 cardiac-gates only, and combined 6 respiratory-gates & 8 cardiac-gates projection datasets. Each dataset was reconstructed using 3D OS-EM without and with attenuation correction using the averaged and respiratory-gated attenuation maps, and the resulting reconstructed images were compared. These results were used to demonstrate the effects of R&C motions and the reduction of image artifact due to R&C motions by gating and attenuation corrections. We concluded that the realistic 4D NCAT phantom and Monte Carlo simulated SPECT projection datasets with R&C motions are powerful tools in the study of the effects of R&C motions, as well as in the development of R&C gating schemes and motion

  17. The development and initial evaluation of a realistic simulated SPECT dataset with simultaneous respiratory and cardiac motion for gated myocardial perfusion SPECT

    Science.gov (United States)

    Lee, Taek-Soo; Tsui, Benjamin M. W.

    2015-02-01

    We developed a realistic simulation dataset for simultaneous respiratory and cardiac (R&C) gated SPECT/CT using the 4D NURBS-based Cardiac-Torso (NCAT) Phantom and Monte Carlo simulation methods, and evaluated it for a sample application study. The 4D NCAT phantom included realistic respiratory motion and beating heart motion based on respiratory gated CT and cardiac tagged MRI data of normal human subjects. To model the respiratory motion, a set of 24 separate 3D NCAT phantoms excluding the heart was generated over a respiratory cycle. The beating heart motion was modeled separately with 48 frames per cardiac cycle for each of the 24 respiratory phases. The resultant set of 24  ×  48 3D NCAT phantoms provides a realistic model of a normal human subject at different phases of combined R&C motions. An almost noise-free SPECT projection dataset for each of the 1152 3D NCAT phantoms was generated using Monte Carlo simulation techniques and the radioactivity uptake distribution of 99mTc sestamibi in different organs. By grouping and summing the separate projection datasets, separate or simultaneous R&C gated acquired data with different gating schemes could be simulated. In the initial evaluation, we combined the projection datasets into ungated, 6 respiratory-gates only, 8 cardiac-gates only, and combined 6 respiratory-gates & 8 cardiac-gates projection datasets. Each dataset was reconstructed using 3D OS-EM without and with attenuation correction using the averaged and respiratory-gated attenuation maps, and the resulting reconstructed images were compared. These results were used to demonstrate the effects of R&C motions and the reduction of image artifact due to R&C motions by gating and attenuation corrections. We concluded that the realistic 4D NCAT phantom and Monte Carlo simulated SPECT projection datasets with R&C motions are powerful tools in the study of the effects of R&C motions, as well as in the development of R&C gating schemes and motion

  18. Estimation of Pulmonary Motion in Healthy Subjects and Patients with Intrathoracic Tumors Using 3D-Dynamic MRI: Initial Results

    Energy Technology Data Exchange (ETDEWEB)

    Plathow, Christian; Schoebinger, Max; Meinzer, Heinz Peter [German Cancer Research Center, Heidelberg (Germany); Herth, Felix; Tuengerthal, Siegfried [Clinic of Thoracic Disease, Heidelberg (Germany); Kauczor, Hans Ulrich [University of Heidelberg, Heidelberg (Germany)

    2009-12-15

    To estimate a new technique for quantifying regional lung motion using 3D-MRI in healthy volunteers and to apply the technique in patients with intra- or extrapulmonary tumors. Intraparenchymal lung motion during a whole breathing cycle was quantified in 30 healthy volunteers using 3D-dynamic MRI (FLASH [fast low angle shot] 3D, TRICKS [time-resolved interpolated contrast kinetics]). Qualitative and quantitative vector color maps and cumulative histograms were performed using an introduced semiautomatic algorithm. An analysis of lung motion was performed and correlated with an established 2D-MRI technique for verification. As a proof of concept, the technique was applied in five patients with non-small cell lung cancer (NSCLC) and 5 patients with malignant pleural mesothelioma (MPM). The correlation between intraparenchymal lung motion of the basal lung parts and the 2D-MRI technique was significant (r = 0.89, p < 0.05). Also, the vector color maps quantitatively illustrated regional lung motion in all healthy volunteers. No differences were observed between both hemithoraces, which was verified by cumulative histograms. The patients with NSCLC showed a local lack of lung motion in the area of the tumor. In the patients with MPM, there was global diminished motion of the tumor bearing hemithorax, which improved significantly after chemotherapy (CHT) (assessed by the 2D- and 3D-techniques) (p < 0.01). Using global spirometry, an improvement could also be shown (vital capacity 2.9 {+-} 0.5 versus 3.4 L {+-} 0.6, FEV1 0.9 {+-} 0.2 versus 1.4 {+-} 0.2 L) after CHT, but this improvement was not significant. A 3D-dynamic MRI is able to quantify intraparenchymal lung motion. Local and global parenchymal pathologies can be precisely located and might be a new tool used to quantify even slight changes in lung motion (e.g. in therapy monitoring, follow-up studies or even benign lung diseases)

  19. Motion of the two-control airplane in rectilinear flight after initial disturbances with introduction of controls following an exponential law

    Science.gov (United States)

    Klemin, Alexander

    1937-01-01

    An airplane in steady rectilinear flight was assumed to experience an initial disturbance in rolling or yawing velocity. The equations of motion were solved to see if it was possible to hasten recovery of a stable airplane or to secure recovery of an unstable airplane by the application of a single lateral control following an exponential law. The sample computations indicate that, for initial disturbances complex in character, it would be difficult to secure correlation with any type of exponential control. The possibility is visualized that the two-control operation may seriously impair the ability to hasten recovery or counteract instability.

  20. A simple probabilistic model of initiation of motion of poorly-sorted granular mixtures subjected to a turbulent flow

    Science.gov (United States)

    Ferreira, Rui M. L.; Ferrer-Boix, Carles; Hassan, Marwan

    2015-04-01

    Initiation of sediment motion is a classic problem of sediment and fluid mechanics that has been studied at wide range of scales. By analysis at channel scale one means the investigation of a reach of a stream, sufficiently large to encompass a large number of sediment grains but sufficiently small not to experience important variations in key hydrodynamic variables. At this scale, and for poorly-sorted hydraulically rough granular beds, existing studies show a wide variation of the value of the critical Shields parameter. Such uncertainty constitutes a problem for engineering studies. To go beyond Shields paradigm for the study of incipient motion at channel scale this problem can be can be cast in probabilistic terms. An empirical probability of entrainment, which will naturally account for size-selective transport, can be calculated at the scale of the bed reach, using a) the probability density functions (PDFs) of the flow velocities {{f}u}(u|{{x}n}) over the bed reach, where u is the flow velocity and xn is the location, b) the PDF of the variability of competent velocities for the entrainment of individual particles, {{f}{{up}}}({{u}p}), where up is the competent velocity, and c) the concept of joint probability of entrainment and grain size. One must first divide the mixture in into several classes M and assign a correspondent frequency p_M. For each class, a conditional PDF of the competent velocity {{f}{{up}}}({{u}p}|M) is obtained, from the PDFs of the parameters that intervene in the model for the entrainment of a single particle: [ {{u}p}/√{g(s-1){{di}}}={{Φ }u}( { {{C}k} },{{{φ}k}},ψ,{{u}p/{di}}{{{ν}(w)}} )) ] where { Ck } is a set of shape parameters that characterize the non-sphericity of the grain, { φk} is a set of angles that describe the orientation of particle axes and its positioning relatively to its neighbours, ψ is the skin friction angle of the particles, {{{u}p}{{d}i}}/{{{ν}(w)}} is a particle Reynolds number, di is the sieving

  1. Eastern Scheldt Sand, Baskarp Sand No. 15

    DEFF Research Database (Denmark)

    Andersen, A. T; Madsen, E. B.; Schaarup-Jensen, A. L.

    The present data report contains data from 13 drained triaxial tests, performed on two different sand types in the Soil Mechanics Laboratory at Aalborg University in March, 1997. Two tests have been performed on Baskarp Sand No. 15, which has already ken extensively tested in the Soil Mechanics...... Laboratory. The remaining 11 triaxial tests have ben performed on Eastern Scheldt Sand, which is a material not yet investigated at the Soil Mechanics Laboratory. In the first pari of this data report, the characteristics of the two sand types in question will be presented. Next, a description...

  2. Fresh groundwater resources in a large sand replenishment

    NARCIS (Netherlands)

    Huizer, Sebastian; Oude Essink, G.H.P.; Bierkens, Marc

    2016-01-01

    The anticipation of sea-level rise and increases in extreme weather conditions has led to the initiation of an innovative coastal management project called the Sand Engine. In this pilot project a large volume of sand (21.5 million m3) – also called sand replenishment or nourishment – was placed on

  3. Mineral processing of heavy mineral sands from Malawi and Malaysia

    OpenAIRE

    Mitchell, C J

    1992-01-01

    Processing of heavy mineral sands involves many techniques including gravity, magnetic and electrostatic separation. As part of a laboratory programme to develop effective mineral processing techniques, two mineral sands from Malawi and Malaysia were processed using the standard techniques, with emphasis placed on the Carpco electrostatic separator. These sands were initially characterised mineralogically by scanning electron microscopy (SEM), electron microprobe analysis (EPMA...

  4. Analysis of sand particles' lift-off and incident velocities in wind-blown sand flux

    Institute of Scientific and Technical Information of China (English)

    Tian-Li Bo; Xiao-Jing Zheng; Shao-Zhen Duan; Yi-Rui Liang

    2013-01-01

    In the research of windblown sand movement,the lift-off and incident velocities of saltating sand particles play a significant role in bridging the spatial and temporal scales from single sand particle's motion to windblown sand flux.In this paper,we achieved wind tunnel measurements of the movement of sand particles near sand bed through improving the wind tunnel experimental scheme of paticle image velocimetry (PIV) and data processing method.And then the influence of observation height on the probability distributions of lift-off and incident velocities of sand particles was analyzed.The results demonstrate that the observation height has no obvious influence on the distribution pattern of the lift-off and incident velocities of sand particles,i.e.,the probability distribution of horizontal and vertical velocities of lift-off and incident sand particles follow a Gaussian distribution and a negative exponential distribution,respectively.However,it influences the center of the Gaussian distribution,the decay constant and the amplitude of the negative exponential distribution.

  5. Discrete particle simulation of mixed sand transport

    Institute of Scientific and Technical Information of China (English)

    Fengjun Xiao; Liejin Guo; Debiao Li; Yueshe Wang

    2012-01-01

    An Eulerian/Lagrangian numerical simulation is performed on mixed sand transport.Volume averaged Navier-Stokes equations are solved to calculate gas motion,and particle motion is calculated using Newton's equation,involving a hard sphere model to describe particle-to-particle and particle-to-wall collisions.The influence of wall characteristics,size distribution of sand particles and boundary layer depth on vertical distribution of sand mass flux and particle mean horizontal velocity is analyzed,suggesting that all these three factors affect sand transport at different levels.In all cases,for small size groups,sand mass flux first increases with height and then decreases while for large size groups,it decreases exponentially with height and for middle size groups the behavior is in-between.The mean horizontal velocity for all size groups well fits experimental data,that is,increasing logarithmically with height in the middle height region.Wall characteristics greatly affects particle to wall collision and makes the flat bed similar to a Gobi surface and the rough bed similar to a sandy surface.Particle size distribution largely affects the sand mass flux and the highest heights they can reach especially for larger particles.

  6. A Hubble Astrometry Initiative: Laying the Foundation for the Next-Generation Proper-Motion Survey of the Local Group

    CERN Document Server

    Kallivayalil, Nitya; Simon, Joshua D; Boylan-Kolchin, Michael; Deason, Alis J; Fritz, Tobias K; Geha, Marla; Sohn, Sangmo Tony; Weisz, Daniel R

    2015-01-01

    High-precision astrometry throughout the Local Group is a unique capability of the Hubble Space Telescope (HST), with potential for transformative science, including constraining the nature of dark matter, probing the epoch of reionization, and understanding key physics of galaxy evolution. While Gaia will provide unparalleled astrometric precision for bright stars in the inner halo of the Milky Way, HST is the only current mission capable of measuring accurate proper motions for systems at greater distances (> 80 kpc), which represents the vast majority of galaxies in the Local Group. The next generation of proper-motion measurements will require long time baselines, spanning many years to decades and possibly multiple telescopes, combining HST with the James Webb Space Telescope (JWST) or the Wide-Field Infrared Survey Telescope (WFIRST). However, the current HST allocation process is not conducive to such multi-cycle/multi-mission science, which will bear fruit primarily over many years. We propose an HST ...

  7. ANALISIS PREDIKSI MOTION SICKNESS INCIDENCE (MSI PADA KAPAL CATAMARAN 1000 GT DALAM TAHAP DESAIN AWAL (INITIAL DESIGN

    Directory of Open Access Journals (Sweden)

    Mardi Santoso

    2015-02-01

    Full Text Available Gerakan kapal terombang – ambing atau naik turun di laut lepas yang diakibatkan oleh ombak yang besar dan terus menerus dapat mengakibatkan gejala sakit berupa kepala pusing, mual bahkan muntah yang seringkali diistilahkan sebagai mabuk laut (sea sickness atau motion sickness.  Pada kapal penumpang(ferrykondisi ini menjadi suatu persyaratan penting yang harus dipertimbangkan dalam proses desain. Dalam penelitian ini dilakukan kajian terhadap hasil perhitungan dan simulasi percepatan vertikal gerakan kapal catamaran 1000GT sehingga bisa dilihat unjuk kerja kapal terhadap kenyamanan penumpang. Kenyamanan pada penumpang dilihat dari indeks jumlah penumpang yang mengalami mabuk laut pada periode tertentu dengan mengacu pada standard ISO-2631/1997. Perhitungan dan simulasi dilakukan pada beberapat titik di kapal untuk melihat percepatan vertikal yang terjadi. Dari hasil simulasi didapatkan pengaruh dari lokasi pengukuran, durasi dan arah ombak terhadap persentase jumlah penumpang yang mengalami gejala mabuk laut atau motion sickness incidence (MSI.

  8. Study of the anti-sand sucker rod pump

    Science.gov (United States)

    Wei, Hangxin; Lv, Bingxin; Xi, Wenkui; Yi, Peng

    2017-06-01

    In order to solve the problem of sand stuck in the sucker rod pump, an anti-sand sucker rod pump is designed. The anti-sand sucker rod pump includes the conventional sucker rod pump and the swirl flow device. The sand particles can be separated from the oil in the swirl flow device, so the plunger of the sucker rod pump cannot be stuck. The motion equation of the sand particles in oil is deduced. The virtual model of the swirl flow device is built in GAMBIT software. And simulation of solid-liquid two phase flow is simulated in software FLUENT. The simulation results show that the swirl flow device can realize the sand particles separation from the oil completely. So the pump can have the effect of anti-sands.

  9. Impact of the initial specification of moisture and vertical motion on precipitation forecasts with a mesoscale model Implications for a satellite mesoscale data base

    Science.gov (United States)

    Mlynczak, Pamela E.; Houghton, David D.; Diak, George R.

    1986-01-01

    Using a numerical mesoscale model, four simulations were performed to determine the effects of suppressing the initial mesoscale information in the moisture and wind fields on the precipitation forecasts. The simulations included a control forecast 12-h simulation that began at 1200 GMT March 1982 and three experiment simulations with modifications to the moisture and vertical motion fields incorporated at 1800 GMT. The forecasts from 1800 GMT were compared to the second half of the control forecast. It was found that, compared to the control forecast, suppression of the moisture and/or wind initial field(s) produces a drier forecast. However, the characteristics of the precipitation forecasts of the experiments were not different enough to conclude that either mesoscale moisture or mesoscale vertical velocity at the initial time are more important for producing a forecast closer to that of the control.

  10. Influence green sand system by core sand additions

    OpenAIRE

    N. Špirutová; J. Beňo; V. Bednářová; J. Kříž; M. Kandrnál

    2012-01-01

    Today, about two thirds of iron alloys casting (especially for graphitizing alloys of iron) are produced into green sand systems with usually organically bonded cores. Separation of core sands from the green sand mixture is very difficult, after pouring. The core sand concentration increase due to circulation of green sand mixture in a closed circulation system. Furthermore in some foundries, core sands have been adding to green sand systems as a replacement for new sands. The goal of this co...

  11. Baskarp Sand No. 15

    DEFF Research Database (Denmark)

    Borup, Marianne; Hedegaard, Jette

    The Soil Mechanics Laboratory has started performing tests with a new sand, Baskarp No 15. Baskarp No 15 is a graded sand from Sweden. The shapes of the largest grains are round, while the small grains have sharp edges. The main part of of Baskarp No 15 is quarts, but it also contains feldspar...... and biotit. Mainly the sand will be used for tests concerning the development og the theory of building up pore pressure in sand, L. B. Ibsen 1993....

  12. Threshold for sand mobility on Mars calibrated from seasonal variations of sand flux

    Science.gov (United States)

    Ayoub, F.; Avouac, J.-P.; Newman, C. E.; Richardson, M. I.; Lucas, A.; Leprince, S.; Bridges, N. T.

    2014-09-01

    Coupling between surface winds and saltation is a fundamental factor governing geological activity and climate on Mars. Saltation of sand is crucial for both erosion of the surface and dust lifting into the atmosphere. Wind tunnel experiments along with measurements from surface meteorology stations and modelling of wind speeds suggest that winds should only rarely move sand on Mars. However, evidence for currently active dune migration has recently accumulated. Crucially, the frequency of sand-moving events and the implied threshold wind stresses for saltation have remained unknown. Here we present detailed measurements of Nili Patera dune field based on High Resolution Imaging Science Experiment images, demonstrating that sand motion occurs daily throughout much of the year and that the resulting sand flux is strongly seasonal. Analysis of the seasonal sand flux variation suggests an effective threshold for sand motion for application to large-scale model wind fields (1-100 km scale) of τs=0.01±0.0015 N m-2.

  13. Lund Sand No 0

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Jakobsen, Finn Rosendal

    During the last 15 years the Geotechnical Engineering Group (GEG) at Aalborg University has performed triaxial tests with a sand called Lund No 0. Lund No 0 is a graded sand from a gravel pit near Horsens in Denmark. For the classification of the sand the following tests have been performed: Sieve...

  14. Amplitude equation and long-range interactions in underwater sand ripples in one dimension

    DEFF Research Database (Denmark)

    Schnipper, Teis; Mertens, Keith; Ellegaard, Clive;

    2008-01-01

    We present an amplitude equation for sand ripples under oscillatory flow in a situation where the sand is moving in a narrow channel and the height profile is practically one dimensional. The equation has the form h(t)=epsilon-(h-(h) over bar) + ((h(x))(2)-1)h(xx)-h(xxxx) + delta((h(x))(2))(xx) w...... finally present surprising experimental results showing that long-range coupling is indeed seen in the initial details of the doubling transition, where in fact two small ripples are initially formed, followed by global symmetry breaking removing one of them....... in particular on the so-called doubling transition, a secondary instability caused by the sudden decrease in the amplitude of the water motion, leading to the appearance of a new ripple in each trough. This transition is well reproduced for sufficiently large delta (asymmetry between trough and crest). We...

  15. Adsorption of dyes on Sahara desert sand.

    Science.gov (United States)

    Varlikli, Canan; Bekiari, Vlasoula; Kus, Mahmut; Boduroglu, Numan; Oner, Ilker; Lianos, Panagiotis; Lyberatos, Gerasimos; Icli, Siddik

    2009-10-15

    Sahara desert sand (SaDeS) was employed as a mineral sorbent for retaining organic dyes from aqueous solutions. Natural sand has demonstrated a strong affinity for organic dyes but significantly lost its adsorption capacity when it was washed with water. Therefore, characterization of both natural and water washed sand was performed by XRD, BET, SEM and FTIR techniques. It was found that water-soluble kyanite, which is detected in natural sand, is the dominant factor affecting adsorbance of cationic dyes. The sand adsorbs over 75% of cationic dyes but less than 21% for anionic ones. Among the dyes studied, Methylene Blue (MB) demonstrated the strongest affinity for Sahara desert sand (Q(e)=11.98 mg/g, for initial dye solution concentration 3.5 x 10(-5)mol/L). The effects of initial dye concentration, the amount of the adsorbent, the temperature and the pH of the solution on adsorption capacity were tested by using Methylene Blue as model dye. Pseudo-first-order, pseudo-second-order and intraparticle diffusion models were applied. It was concluded that adsorption of Methylene Blue on Sahara desert sand followed pseudo-second order kinetics. Gibbs free energy, enthalpy change and entropy change were calculated and found -6411 J/mol, -30360 J/mol and -76.58 J/mol K, respectively. These values indicate that the adsorption is an exothermic process and has a spontaneous nature at low temperatures.

  16. An Approximate Solution to the Equation of Motion for Large-Angle Oscillations of the Simple Pendulum with Initial Velocity

    Science.gov (United States)

    Johannessen, Kim

    2010-01-01

    An analytic approximation of the solution to the differential equation describing the oscillations of a simple pendulum at large angles and with initial velocity is discussed. In the derivation, a sinusoidal approximation has been applied, and an analytic formula for the large-angle period of the simple pendulum is obtained, which also includes…

  17. An Approximate Solution to the Equation of Motion for Large-Angle Oscillations of the Simple Pendulum with Initial Velocity

    Science.gov (United States)

    Johannessen, Kim

    2010-01-01

    An analytic approximation of the solution to the differential equation describing the oscillations of a simple pendulum at large angles and with initial velocity is discussed. In the derivation, a sinusoidal approximation has been applied, and an analytic formula for the large-angle period of the simple pendulum is obtained, which also includes…

  18. Formation mechanism of cracks in saturated sand

    Institute of Scientific and Technical Information of China (English)

    Xiaobing Lu; Zhemin Zheng; Yongren Wu

    2006-01-01

    The formation mechanism of "water film" (or crack) in saturated sand is analyzed theoretically and numerically.The theoretical analysis shows that there will be no stable "water film" in the saturated sand if the strength of the skeleton is zero and no positions are choked.It is shown by numerical simulation that stable water films initiate and grow if the choking state keeps unchanged once the fluid velocities decrease to zero in the liquefied sand column.The developments of "water film" based on the model presented in this paper are compared with experimental results.

  19. Influence green sand system by core sand additions

    Directory of Open Access Journals (Sweden)

    N. Špirutová

    2012-01-01

    Full Text Available Today, about two thirds of iron alloys casting (especially for graphitizing alloys of iron are produced into green sand systems with usually organically bonded cores. Separation of core sands from the green sand mixture is very difficult, after pouring. The core sand concentration increase due to circulation of green sand mixture in a closed circulation system. Furthermore in some foundries, core sands have been adding to green sand systems as a replacement for new sands. The goal of this contribution is: “How the green sand systems are influenced by core sands?”This effect is considered by determination of selected technological properties and degree of green sand system re-bonding. From the studies, which have been published yet, there is not consistent opinion on influence of core sand dilution on green sand system properties. In order to simulation of the effect of core sands on the technological properties of green sands, there were applied the most common used technologies of cores production, which are based on bonding with phenolic resin. Core sand concentration added to green sand system, was up to 50 %. Influence of core sand dilution on basic properties of green sand systems was determined by evaluation of basic industrial properties: moisture, green compression strength and splitting strength, wet tensile strength, mixture stability against staling and physical-chemistry properties (pH, conductivity, and loss of ignition. Ratio of active betonite by Methylene blue test was also determined.

  20. Initial study of biexponential model of intravoxel incoherent motion magnetic resonance imaging in evaluation of the liver fibrosis

    Institute of Scientific and Technical Information of China (English)

    Chen Cuiyun; Wang Bin; Shi Dapeng; Fu Fangfang; Zhang Jiliang; Wen Zejun; Zhu Shaocheng

    2014-01-01

    Background The diagnosis of liver fibrosis is a difficult task at any time using conventional clinical imaging.Intravoxel incoherent motion (IVIM) can be used to investigate both diffusion and perfusion changes in tissues.This study was designed to determine the value of IVIM in the diagnosis and staging of liver fibrosis.Methods IVIM examinations were performed on a GE 3.0T MR scanner in 25 patients with liver fibrosis and 25 healthy volunteers as the control group.Patients with liver fibrosis diagnosis were confirmed by pathology and staged on a scale of F0-4.The standard ADC values and the values of a biexponential model (slow ADC (Dslow),fast ADC (Dfast) and fraction of fast ADC (FF)) were measured in three liver regions per person.The mean standard ADC values,Dslow values,Dfast values and FF values from the study group were compared among the right posterior hepatic lobe,right anterior hepatic lobe and medial segment of the left lobe.Receiver Operating Characteristic (ROC) curves and independent-samples t-tests were used to calculate the mean standard ADC values,Dslow values,Dfast values and FF values from the study group and the control group.Spearman rho correlation analysis was used for the stage of liver fibrosis.The liver fibrosis stages between the groups F0-1 and F2-4,the groups F0-2 and F3-4 were compared.Results Among the liver fibrosis,there was no significant difference in the mean standard ADC values,Dslow values,Dfast values,and FF values obtained from the right posterior hepatic lobe,right anterior hepatic lobe and medial segment of the left lobe.Using ROC analysis,the Area Under the Curve (AUC) values of standard ADC,Dslow,Dfast,FF were all between 0.7 to 0.9.The mean standard ADC values,Dslow values,Dfast values and FF values of the liver in the study group were significantly lower than the values in the control group (P <0.05).As the stage of the fibrosis increased,the values decreased by Spearman rho correlation analysis.The mean values

  1. Sands cykliske styrke

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo

    1992-01-01

    Sands cykliske styrke kan beskrives ved Cyclic Liquefaction, Mobilisering, Stabilization og Instant Stabilization. I artiklen beskrives hvorfor Stabilization og Instant Stabilization ikke observeres, når sands udrænede styrke undersøges i triaxial celler, der anvender prøver med dobbelt prøvehøjde....

  2. Baskarp Sand No. 15

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Bødker, Lars Bødker

    The Soil Mechanics Laboratory has started performing tests with a new sand, Baskarp No 15. Baskarp No 15 is a graded sand from Sweden. The shapes of the largest grains are round, while the small grains have sharp edges. The main part of of Baskarp No 15 is quarts, but it also contains feldspar...

  3. Developing a Sand Management Plan for Galveston Island

    Science.gov (United States)

    2015-10-16

    US Army Corps of Engineers BUILDING STRONG® Developing a Sand Management Plan for Galveston Island Ashley E. Frey, P. E. Research Civil...GenCade Alternatives • Sand Management Alternatives and Plan • Beach Nourishment Project 2 Innovative solutions for a safer, better world...BUILDING STRONG® Problem Statement/Approach Recommend a long-term plan of actions to better manage sands on Galveston Island Initial Tasks

  4. Analytical calculation of the minimum wind speed required to sustain wind-blown sand on Earth and Mars

    CERN Document Server

    Kok, Jasper F

    2010-01-01

    The wind-driven hopping motion of sand grains, known as saltation, forms dunes and ripples and ejects fine dust particles into the atmosphere on both Earth and Mars. While the wind speed at which saltation is initiated, the fluid threshold, has been studied extensively, the wind speed at which it is halted, the impact threshold, has been poorly quantified for Mars conditions. We present an analytical model of the impact threshold, which we show to be in agreement with measurements and recent numerical simulations for Earth conditions. For Mars conditions, we find that the impact threshold is approximately an order of magnitude below the fluid threshold, in agreement with previous studies. Saltation on Mars can thus be sustained at wind speeds an order of magnitude less than required to initiate it, leading to the occurrence of hysteresis. These results confirm earlier simulations with a detailed numerical saltation model, and have important implications for the formation of sand dunes, ripples, and dust storm...

  5. Sand and Gravel Deposits

    Data.gov (United States)

    Vermont Center for Geographic Information — This dataset is a statewide polygon coverage of sand, gravel, and stone resources. This database includes the best data available from the VT Agency of Natural...

  6. Sand and Gravel Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes sand and gravel operations in the United States. These data were obtained from information reported voluntarily to the USGS by the aggregate...

  7. Vestled - Hvide Sande

    DEFF Research Database (Denmark)

    Juel-Christiansen, Carsten; Hesselbjerg, Marianne; Schønherr, Torben

    2009-01-01

    Værket Vestled i Hvide Sande præsenteret i sammenhæng af 1000 nutidige landskabsarkitektoniske arbejder fra hele verden, hvor hvert værk vises på én side......Værket Vestled i Hvide Sande præsenteret i sammenhæng af 1000 nutidige landskabsarkitektoniske arbejder fra hele verden, hvor hvert værk vises på én side...

  8. MECHANICAL REGENERATION OF SAND WASTE

    Directory of Open Access Journals (Sweden)

    D. I. Gnir

    2005-01-01

    Full Text Available The experimental activation of the sand regenerator of the firm SINTO is carried out at ОАО “MZOO". It is shown that sand grains are cleared from films of binding agents, that allows to use the treated sand for preparation of agglutinant and core sands.

  9. Imaging of Acoustic Waves in Sand

    Energy Technology Data Exchange (ETDEWEB)

    Deason, Vance Albert; Telschow, Kenneth Louis; Watson, Scott Marshall

    2003-08-01

    There is considerable interest in detecting objects such as landmines shallowly buried in loose earth or sand. Various techniques involving microwave, acoustic, thermal and magnetic sensors have been used to detect such objects. Acoustic and microwave sensors have shown promise, especially if used together. In most cases, the sensor package is scanned over an area to eventually build up an image or map of anomalies. We are proposing an alternate, acoustic method that directly provides an image of acoustic waves in sand or soil, and their interaction with buried objects. The INEEL Laser Ultrasonic Camera utilizes dynamic holography within photorefractive recording materials. This permits one to image and demodulate acoustic waves on surfaces in real time, without scanning. A video image is produced where intensity is directly and linearly proportional to surface motion. Both specular and diffusely reflecting surfaces can be accomodated and surface motion as small as 0.1 nm can be quantitatively detected. This system was used to directly image acoustic surface waves in sand as well as in solid objects. Waves as frequencies of 16 kHz were generated using modified acoustic speakers. These waves were directed through sand toward partially buried objects. The sand container was not on a vibration isolation table, but sat on the lab floor. Interaction of wavefronts with buried objects showed reflection, diffraction and interference effects that could provide clues to location and characteristics of buried objects. Although results are preliminary, success in this effort suggests that this method could be applied to detection of buried landmines or other near-surface items such as pipes and tanks.

  10. SLOW MOTION Is Required for Within-Plant Auxin Homeostasis and Normal Timing of Lateral Organ Initiation at the Shoot Meristem in Arabidopsis[C][W

    Science.gov (United States)

    Lohmann, Daniel; Stacey, Nicola; Breuninger, Holger; Jikumaru, Yusuke; Müller, Dörte; Sicard, Adrien; Leyser, Ottoline; Yamaguchi, Shinjiro; Lenhard, Michael

    2010-01-01

    The regular arrangement of leaves and flowers around a plant's stem is a fascinating expression of biological pattern formation. Based on current models, the spacing of lateral shoot organs is determined by transient local auxin maxima generated by polar auxin transport, with existing primordia draining auxin from their vicinity to restrict organ formation close by. It is unclear whether this mechanism encodes not only spatial information but also temporal information about the plastochron (i.e., the interval between the formation of successive primordia). Here, we identify the Arabidopsis thaliana F-box protein SLOW MOTION (SLOMO) as being required for a normal plastochron. SLOMO interacts genetically with components of polar auxin transport, and mutant shoot apices contain less free auxin. However, this reduced auxin level at the shoot apex is not due to increased polar auxin transport down the stem, suggesting that it results from reduced synthesis. Independently reducing the free auxin level in plants causes a similar lengthening of the plastochron as seen in slomo mutants, suggesting that the reduced auxin level in slomo mutant shoot apices delays the establishment of the next auxin maximum. SLOMO acts independently of other plastochron regulators, such as ALTERED MERISTEM PROGRAM1 or KLUH/CYP78A5. We propose that SLOMO contributes to auxin homeostasis in the shoot meristem, thus ensuring a normal rate of the formation of auxin maxima and organ initiation. PMID:20139162

  11. Bituminous sands : tax issues

    Energy Technology Data Exchange (ETDEWEB)

    Patel, B. [PricewaterhouseCoopers LLP, Calgary, AB (Canada)

    2004-07-01

    This paper examined some of the tax issues associated with the production of bitumen or synthetic crude oil from oil sands. The oil sands deposits in Alberta are gaining more attention as the supplies of conventional oil in Canada decline. The oil sands reserves located in the Athabasca, Cold Lake and Peace River areas contain about 2.5 trillion barrels of highly viscous hydrocarbons called bitumen, of which nearly 315 billion barrels are recoverable with current technology. The extraction method varies for each geographic area, and even within zones and reservoirs. The two most common extraction methods are surface mining and in-situ extraction such as cyclic steam stimulation (CSS); low pressure steam flood; pressure cycle steam drive; steam assisted gravity drainage (SAGD); hot water flooding; and, fire flood. This paper also discussed the following general tax issues: bituminous sands definition; bituminous sands leases and Canadian development expense versus Canadian oil and gas property expense (COGPE); Canadian exploration expense (CEE) for surface mining versus in-situ methods; additional capital cost allowance; and, scientific research and experimental development (SR and ED). 15 refs.

  12. MRI-based motion correction of thoracic PET: initial comparison of acquisition protocols and correction strategies suitable for simultaneous PET/MRI systems

    Energy Technology Data Exchange (ETDEWEB)

    Dikaios, Nikolaos; Fryer, Tim D. [University of Cambridge, Wolfson Brain Imaging Centre, Department of Clinical Neurosciences, Cambridge (United Kingdom); Izquierdo-Garcia, David; Mani, Venkatesh; Fayad, Zahi A. [Mount Sinai School of Medicine, Imaging Science Laboratories, Translational and Molecular Imaging Institute, Department of Radiology, New York, NY (United States); Graves, Martin J. [University of Cambridge, Department of Radiology, Cambridge (United Kingdom)

    2012-02-15

    Magnetic resonance imaging (MRI) acquired on equipment capable of simultaneous MRI and positron emission tomography (PET) could potentially provide the gold standard method for motion correction of PET. To assess the latter, in this study we compared fast 2D and 3D MRI of the torso and used deformation parameters from real MRI data to correct simulated PET data for respiratory motion. PET sinogram data were simulated using SimSET from a 4D pseudo-PET image series created by segmenting MR images acquired over a respiratory cycle. Motion-corrected PET images were produced using post-reconstruction registration (PRR) and motion-compensated image reconstruction (MCIR). MRI-based motion correction improved PET image quality at the lung-liver and lung-spleen boundaries and in the heart but little improvement was obtained where MRI contrast was low. The root mean square error in SUV units per voxel compared to a motion-free image was reduced from 0.0271 (no motion correction) to 0.0264 (PRR) and 0.0250 (MCIR). Motion correction using MRI can improve thoracic PET images but there are limitations due to the quality of fast MRI. (orig.)

  13. Lund Sand No 0

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Jakobsen, Finn Rosendal

    During the last 15 years the Geotechnical Engineering Group (GEG) at Aalborg University has performed triaxial tests with a sand called Lund No 0. Lund No 0 is a graded sand from a gravel pit near Horsens in Denmark. For the classification of the sand the following tests have been performed: Sieve...... test, Grain density, ds, Maximum, emax, and minimum, emin, void ratio. The strength parameters of Lund No 0 are detennined by some drained and undrained triaxial tests in the Danish Triaxial Cell. The Danish Triaxial Cell prescribes smooth pressure heads and specimens with equal height and diameter....... Four series with Id equal to 0.92, 0.87 0.76 and 0.55 have been performed....

  14. Locomotory transition from water to sand and its effects on undulatory kinematics in sand lances (Ammodytidae).

    Science.gov (United States)

    Gidmark, Nicholas J; Strother, James A; Horton, Jaquan M; Summers, Adam P; Brainerd, Elizabeth L

    2011-02-15

    Sand lances, fishes in the genus Ammodytes, exhibit a peculiar burrowing behavior in which they appear to swim rapidly into the substrate. They use posteriorly propagated undulations of the body to move in both water, a Newtonian fluid, and in sand, a non-Newtonian, granular substrate. In typical aquatic limbless locomotion, undulations of the body push against water, which flows because it is incapable of supporting the static stresses exerted by the animal, thus the undulations move in world space (slipping wave locomotion). In typical terrestrial limbless locomotion, these undulations push against substrate irregularities and move relatively little in world space (non-slipping wave locomotion). We used standard and X-ray video to determine the roles of slipping wave and non-slipping wave locomotion during burrowing in sand lances. We find that sand lances in water use slipping wave locomotion, similar to most aquatic undulators, but switch to non-slipping waves once they burrow. We identify a progression of three stages in the burrowing process: first, aquatic undulations similar to typical anguilliform locomotion (but without head yaw) push the head into the sand; second, more pronounced undulations of the aquatic portion of the body push most of the animal below ground; third, the remaining above-ground portion of the body ceases undulation and the subterranean portion takes over, transitioning to non-slipping wave locomotion. We find no evidence that sand lances use their body motions to fluidize the sand. Instead, as soon as enough of the body is underground, they undergo a kinematic shift and locomote like terrestrial limbless vertebrates.

  15. UK Frac Sand Resources

    OpenAIRE

    Mitchell, C J

    2015-01-01

    Although still just a glimmer in the gas man’s eye, the prospect of shale hydrocarbon (oil and gas) development in the UK has many companies thinking about the industrial minerals it will require. Chief amongst these is silica sand which is used as a ‘proppant’ in the hydraulic fracturing, or ‘fracking’, of shales to help release the gas. The UK has large resources of sand and sandstone, of which only a small proportion have the necessary technical properties that classify them as ‘silica san...

  16. Mitigating in situ oil sands carbon costs

    Energy Technology Data Exchange (ETDEWEB)

    Theriault, D.J.; Peterson, J. [Laricina Energy Ltd., Calgary, AB (Canada); Heinrichs, H. [Canadian Chemical Technology Inc., Calgary, AB (Canada)

    2008-10-15

    Carbon capture and sequestration is a complex problem with a variety of dimensions that need to be considered. The political, social, and regulatory pressures are forcing carbon costs on the oil sands industry in an effort to reduce the carbon footprint of oil sands operations. This paper reviewed the political, social, and regulatory pressures and obligations for the in-situ oil sands industry. It presented the views and insights of Laricina Energy on the carbon challenge. It also described the initiatives that Laricina Energy is taking to manage these imperatives and outlined the challenges the industry is facing. The purpose of the paper was to encourage dialogue and collaboration by the oil sands industry. The paper also described the dimensions of the carbon problem and how the industry can contribute to a solution. Last, the paper reviewed the parameters of carbon dioxide or greenhouse gas containment and storage issues. It was concluded that the regulatory and policy requirements need to be clarified so that industry understands the new business landscape as well as the requirements that influence the economics of in-situ oil sands development. 7 refs., 7 figs.

  17. Building with Sand

    Science.gov (United States)

    Ashbrook, Peggy

    2010-01-01

    Children playing in damp sand invariably try to make a tower or a tunnel. By providing experiences with a variety of materials, alone and together, teachers set up the conditions for children to learn through their senses and ensure that a class approaches a topic with a common set of experiences to build on. Learning about the properties of…

  18. Faraday, Jets, and Sand

    NARCIS (Netherlands)

    Sandtke, M.; van der Meer, Roger M.; Versluis, Andreas Michel; Lohse, Detlef

    2003-01-01

    When a 6-mm layer of fine sand with an average grain size of 40 µm is poured into a cylindrical container and shaken vertically, thin jets are seen to emerge from an airy cloud of grains, almost like protuberances from the corona of the sun. A quasi two-dimensional setup reveals the jet-formation

  19. Building with Sand

    Science.gov (United States)

    Ashbrook, Peggy

    2010-01-01

    Children playing in damp sand invariably try to make a tower or a tunnel. By providing experiences with a variety of materials, alone and together, teachers set up the conditions for children to learn through their senses and ensure that a class approaches a topic with a common set of experiences to build on. Learning about the properties of…

  20. Speleothems and Sand Castles

    Science.gov (United States)

    Hance, Trevor; Befus, Kevin

    2015-01-01

    The idea of building sand castles evokes images of lazy summer days at the beach, listening to waves crash, enjoying salty breezes, and just unplugging for a while to let our inner child explore the wonderful natural toys beneath our feet. The idea of exploring caves might evoke feelings and images of claustrophobia or pioneers and Native…

  1. Virksomhedens sande ansigt

    DEFF Research Database (Denmark)

    Lundholt, Marianne Wolff

    2017-01-01

    Er modhistorier en byrde eller en styrke i forandringsprocesser? Hvad stiller vi op, når adgangen til organisationens sande identitet går gennem medarbejdernes modhistorier? Når vi sammenholder denne erkendelse med vores viden om, at medarbejdere helt naturligt afholder sig fra at videregive disse...

  2. Sand (CSW4)

    CSIR Research Space (South Africa)

    Estuarine and Coastal Research Unit

    1982-12-01

    Full Text Available This report is one of a series on Cape Estuaries being published under the general title "The Estuaries of the Cape, Part 2". The report provides information on sand estuary: historical background, abiotic and biotic characteristics. It is pointed...

  3. Sand supply to beaches

    Science.gov (United States)

    Aagaard, Troels

    2017-04-01

    In most cases, beaches and dunes are built by sand that has been transported onshore from the shoreface. While this has been known for a long time, we are still not able to quantitatively predict onshore sediment transport and sand supply to beaches. Sediment transport processes operating during brief, high-energy stormy conditions - when beaches erode and sand moves offshore - are fairly well known and they can be modelled with a reasonable degree of confidence. However, the slower onshore sand transport leading to beach recovery under low-to-moderate energy conditions - and the reason why beaches and dunes exist in the first place - is not yet well understood. This severely limits our capability to understand and predict coastal behaviour on long time scales, for example in response to changing sea level or wave conditions. This paper will discuss issues and recent developments in sediment transport measurement and prediction on the lower and upper shoreface and into the swash zone. The focus will be on the integration and upscaling of small-scale deterministic process measurements into parametric models that may increase modelling capabilities of coastal behaviour on larger temporal and spatial scales.

  4. Erosion phenomena in sand moulds

    Directory of Open Access Journals (Sweden)

    A. Chojecki

    2008-03-01

    Full Text Available Authors studicd the erosion phcnorncna in sand moulds pured with cast iron. Thc study comprises an evaluation of erosionresistance of thc three sands: grccn sand. sand bondcd with inorganic or organic bindcr. It was concluded that thc most resistant is [heclassic green sand with thc addition of 5 B coal dust. Resistance of the sand with organic binder is generally weak and dcvnds onkind of used raisin. Spccinl nztcntion was paid to the sands with no organic bindcr watcr glass and phospha~c. It was Sound that thcirrcsistance depends on dehydratation conditions. When the mould is stored in law humidity of atmosphcrc the very strong crosion canbe expected. It rcsul ts hrn thc micro fractures in the bridges of binders, joining the grains of the sable. This phcnomcna facilitates thetearing away of fragments of sand [tom the surface

  5. Classifying Motion.

    Science.gov (United States)

    Duzen, Carl; And Others

    1992-01-01

    Presents a series of activities that utilizes a leveling device to classify constant and accelerated motion. Applies this classification system to uniform circular motion and motion produced by gravitational force. (MDH)

  6. On Pluvial Compaction of Sand

    DEFF Research Database (Denmark)

    Jacobsen, Moust

    At the Institute of Civil Engineering in Aalborg model tests on dry sand specimens have been carried out during the last five years. To reduce deviations in test results, the sand laying technique has been carefully studied, and the sand mass spreader constructed. Preliminary results have been...

  7. LIQUEFACTION AND DISPLACEMENT OF SATURATED SAND UNDER VERTICAL VIBRATION LOADING

    Institute of Scientific and Technical Information of China (English)

    LU Xiaobing; TAN Qingming; CHENG C.M.; YU Shanbing; CUI Peng

    2004-01-01

    In order to investigate the influence of the vertical vibration loading on the liquefaction of saturated sand, one dimensional model for the saturated sand with a vertical vibration is presented based on the two phase continuous media theory. The development of the liquefaction and the liquefaction region are analyzed. It is shown that the vertical vibration loading could induce liquefaction.The rate of the liquefaction increases with the increase of the initial limit strain or initial porosity or amplitude and frequency of loading, and increases with the decrease of the permeability or initial modulus. It is shown also that there is a phase lag in the sand column. When the sand permeability distribution is non-uniform, the pore pressure and the strain will rise sharply where the permeability is the smallest, and fracture might be induced. With the development of liquefaction, the strength of the soil foundation becomes smaller and smaller. In the limiting case, landslides or debris flows could occur.

  8. Sedimentation process of saturated sand under impact loading

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Junfeng; MENG; Xiangyue

    2005-01-01

    The initial small inhomogeneity of saturated sand could be amplified during the sedimentation process after liquefaction, and cracks could be observed in the sand column. Layers of fine sand could also be found at the exact place where cracks developed and disappeared. The phenomena and the whole process were experimentally shown by X-rays images. To account for the phenomena, a linearized stability analysis of the sedimentation of saturated sand was conducted; however, it did not produce a satisfactory result. A three-phase flow model describing the transportation of fine sand is presented in this paper. It is shown that such a kind of erosion/deposition model was qualitatively in good agreement with the experimental observation.

  9. Sand hazards on tourist beaches.

    Science.gov (United States)

    Heggie, Travis W

    2013-01-01

    Visiting the beach is a popular tourist activity worldwide. Unfortunately, the beach environment is abundant with hazards and potential danger to the unsuspecting tourist. While the traditional focus of beach safety has been water safety oriented, there is growing concern about the risks posed by the sand environment on beaches. This study reports on the death and near death experience of eight tourists in the collapse of sand holes, sand dunes, and sand tunnels. Each incident occurred suddenly and the complete burial in sand directly contributed to the victims injury or death in each case report.

  10. PROCESSING OF MONAZITE SAND

    Science.gov (United States)

    Calkins, G.D.; Bohlmann, E.G.

    1957-12-01

    A process for the recovery of thorium, uranium, and rare earths from monazite sands is presented. The sands are first digested and dissolved in concentrated NaOH, and the solution is then diluted causing precipitation of uranium, thorium and rare earth hydroxides. The precipitate is collected and dissolved in HCl, and the pH of this solution is adjusted to about 6, precipitating the hydroxides of thorium and uranium but leaving the rare earths in solution. The rare earths are then separated from the solution by precipitation at a still higher pH. The thorium and uranium containing precipitate is redissolved in HNO/sub 3/ and the two elements are separated by extraction into tributyl phosphate and back extraction with a weakly acidic solution to remove the thorium.

  11. Nonlinear dynamical characteristics of bed load motion

    Institute of Scientific and Technical Information of China (English)

    BAI; Yuchuan; XU; Haijue; XU; Dong

    2006-01-01

    Bed forms of various kinds that evolve naturally on the bottom of sandy coasts and rivers are a result of the kinematics of bed load transport. Based on the group motion of particles in the bed load within the bottom layer, a study on the nonlinear dynamics of bed load transport is presented in this paper. It is found that some development stages, such as the initiation, the equilibrium sediment transport, and the transition from a smooth bed to sand dunes, can be accounted for by different states in the nonlinear system of the bed load transport. It is verified by comparison with experimental data reported by Laboratoire Nationae D'Hydraulique, Chatou, France, that the evolution from a smooth bed to sand dunes is determined by mutation in the bed load transport. This paper presents results that may offer theoretical explanations to the experimental observations. It is also an attempt to apply the state-of-the-art nonlinear science to the classical sediment transport mechanics.

  12. Microwaves energy in curing process of water glass molding sands

    Directory of Open Access Journals (Sweden)

    Granat K.

    2007-01-01

    Full Text Available This work presents the results of investigation of microwave heating on hardening process of water glass molding sands. Essential influence of this heating process on basic properties such as: compression, bending and tensile strength as well as permeability and abrasion resistance has been found. It has been proved, that all investigated sorts of sodium water glass with a module between 2.0 and 3.3 can be used as a binder of molding sands in microwave curing process. It has been found during analysis of research results of sands with 2.5 % water glass addition that they are practically the same as in case of identical molding sands dried for 120 minutes at the temperature of 110°C, used for comparative purposes. Application of microwave curing of molding sands with water glass, however, guarantees reduction of hardening time (from 120 to 4 minutes as well as significant reduction of energy consumption. Attempts of two stage hardening of the investigated water glass molding sands have also been carried out, that is after an initial hardening during a classical CO2 process (identical sands have also been tested for comparison after CO2 blowing process and additional microwave heating. It has been found that application of this kind of treatment for curing sands with 2.5 % sodium water glass content and module from 2.0 up to 3.3 results in the improvement of properties in comparison to classical CO2 process.

  13. SAND: Automated VLBI imaging and analyzing pipeline

    Science.gov (United States)

    Zhang, Ming

    2016-05-01

    The Search And Non-Destroy (SAND) is a VLBI data reduction pipeline composed of a set of Python programs based on the AIPS interface provided by ObitTalk. It is designed for the massive data reduction of multi-epoch VLBI monitoring research. It can automatically investigate calibrated visibility data, search all the radio emissions above a given noise floor and do the model fitting either on the CLEANed image or directly on the uv data. It then digests the model-fitting results, intelligently identifies the multi-epoch jet component correspondence, and recognizes the linear or non-linear proper motion patterns. The outputs including CLEANed image catalogue with polarization maps, animation cube, proper motion fitting and core light curves. For uncalibrated data, a user can easily add inline modules to do the calibration and self-calibration in a batch for a specific array.

  14. Booming Sand Dunes

    Science.gov (United States)

    Vriend, Nathalie

    "Booming" sand dunes are able to produce low-frequency sound that resembles a pure note from a music instrument. The sound has a dominant audible frequency (70-105 Hz) and several higher harmonics and may be heard from far distances away. A natural or induced avalanche from a slip face of the booming dune triggers the emission that may last for several minutes. There are various references in travel literature to the phenomenon, but to date no scientific explanation covered all field observations. This thesis introduces a new physical model that describes the phenomenon of booming dunes. The waveguide model explains the selection of the booming frequency and the amplification of the sound in terms of constructive interference in a confined geometry. The frequency of the booming is a direct function of the dimensions and velocities in the waveguide. The higher harmonics are related to the higher modes of propagation in the waveguide. The experimental validation includes quantitative field research at the booming dunes of the Mojave Desert and Death Valley National Park. Microphone and geophone recordings of the acoustic and seismic emission show a variation of booming frequency in space and time. The analysis of the sensor data quantifies wave propagation characteristics such as speed, dispersion, and nonlinear effects and allows the distinction between the source mechanism of the booming and the booming itself. The migration of sand dunes results from a complicated interplay between dune building, wind regime, and precipitation. The morphological and morphodynamical characteristics of two field locations are analyzed with various geophysical techniques. Ground-penetrating radar images the subsurface structure of the dunes and reveal a natural, internal layering that is directly related to the history of dune migration. The seismic velocity increases abruptly with depth and gradually increases with downhill position due to compaction. Sand sampling shows local

  15. The impact of particle shape on the angle of internal friction and the implications for sediment dynamics at a steep, mixed sand-gravel beach

    Science.gov (United States)

    Stark, N.; Hay, A. E.; Cheel, R.; Lake, C. B.

    2014-08-01

    The impact of particle shape on the angle of internal friction, and the resulting impact on beach sediment dynamics, is still poorly understood. In areas characterized by sediments of specific shape, particularly non-rounded particles, this can lead to large departures from the expected sediment dynamics. The steep slope (1 : 10) of the mixed sand-gravel beach at Advocate Harbour is stable in large-scale morphology over decades, despite a high tidal range of 10 m or more, and intense shore-break action during storms. The Advocate sand (d plate-like shape (Corey Shape Index, CSI ≈ 0.2-0.6). High angles of internal friction of this material were determined using direct shear, ranging from φ ≈ 41 to 49°, while the round to angular gravel was characterized as φ = 33°. The addition of 25% of the elliptic plate-like sand-sized material to the gravel led to an immediate increase in friction angle to φ = 38°. Furthermore, re-organization of the particles occurred during shearing, characterized by a short phase of settling and compaction, followed by a pronounced strong dilatory behavior and an accompanying strong increase of resistance to shear and, thus, shear stress. Long-term shearing (24 h) using a ring shear apparatus led to destruction of the particles without re-compaction. Finally, submerged particle mobilization was simulated using a tilted tray submerged in a water-filled tank. Despite a smooth tray surface, particle motion was not initiated until reaching tray tilt angles of 31° and more, being ≥7° steeper than for motion initiation of the gravel mixtures. In conclusion, geotechnical laboratory experiments quantified the important impact of the elliptic, plate-like shape of Advocate Beach sand on the angles of internal friction of both pure sand and sand-gravel mixtures. The resulting effect on initiation of particle motion was confirmed in tilting tray experiments. This makes it a vivid example of how particle shape can contribute to the

  16. Drained Triaxial Tests on Eastern Scheldt Sand

    DEFF Research Database (Denmark)

    Praastrup, U.; Jakobsen, Kim Parsberg

    In the process of understanding and developing models for geomaterials, the stress-strain behaviour is commonly studied by performing triaxial tests. In the present study static triaxial tests have been performed to gain knowledge of the stress-strain behaviour of frictional materials during...... monotonic loading. The tests reported herein are all drained tests, starting from different initial states of stress and following various stress paths. AIl the tests are performed on reconstituted medium dense specimens of Eastern Scheldt Sand....

  17. Sediment mathematical model for sand ridges and sand waves

    Institute of Scientific and Technical Information of China (English)

    LI Daming; WANG Xiao; WANG Xin; LI Yangyang

    2016-01-01

    A new theoretical model is formulated to describe internal movement mechanisms of the sand ridges and sand waves based on the momentum equation of a solid-liquid two-phase flow under a shear flow. Coupling this equation with two-dimensional shallow water equations and wave reflection-diffraction equation of mild slope, a two-dimensional coupling model is established and a validation is carried out by observed hydrogeology, tides, waves and sediment. The numerical results are compared with available observations. Satisfactory agreements are achieved. This coupling model is then applied to the Dongfang 1-1 Gas Field area to quantitatively predict the movement and evolution of submarine sand ridges and sand waves. As a result, it is found that the sand ridges and sand waves movement distance increases year by year, but the development trend is stable.

  18. Effect of Quartz Sand Characteristics on Initial Filtering Efficiency of ICE Air Filter%石英砂特性对内燃机空气滤清器原始过滤效率测试结果的影响

    Institute of Scientific and Technical Information of China (English)

    崔艳; 梁云; 仲昭琳

    2011-01-01

    In this study, the particle size distribution and morphological characteristics of 270 mesh quartz sand A, B and C which are used to evaluate performance of the ICE air filter were studied. And the air filter initial efficiency was tested using these quartz sands as the test dust separately. The results show that initial efficiency of the same filter are 99.30%, 99.55% and 99.70% respectively with quartz sand A, B and C. The correlation between filtering efficiency and engine wear is analyzed, it is concluded that dust penetration rate of air filter is crucial to the overhaul mileage of vehicle.%对用于内燃机空气滤清器性能评价的A、B、C3种270目石英砂的粒径分布和形态特性进行了分析,并分别以其为试验尘对空气滤清器的原始过滤效率进行了测试.结果表明,使用石英砂A、B、C作为试验尘时,同一滤清器的原始过滤效率分别为99.30% 、99.55%与99.70%.分析了空气滤清器过滤效率和发动机磨损的关系,并得出空气滤清器的灰尘透过率对汽车大修里程有着重大影响的结论.

  19. AEROSOL FILTRATION USING QUARTZ SAND FILTER

    Directory of Open Access Journals (Sweden)

    Abbas H. Sulaymon

    2012-01-01

    Full Text Available The cement industry is the major source of cement dust which contains heavy metals like nickel, cobalt, lead, chromium, arsenic and hazardous substances like dioxins and furans. Exposure to these substances can cause health problems to human, animals and vegetation. A continuous pilot scale quartz sand filter was constructed and uses to study the effect of important design parameters (temperature, pre-loaded dust on the collector, diameter of the filter, bed depth, collector size and superficial velocity on its performance for cleaning of cement dust from air. Initial penetration and initial pressure drop (after 180s were measured and compared for different variables used in this study. The dirty bed was cleaned by means of reverse air flow when the pressure drop across the filter rises to 20 cmH2O. A macroscopic model describes the filter clogging was used to predict the effluent histories based on initial collection efficiency (η0exp which was determined from experimental data. A removal efficiency of more than 99% was obtained. The results show that 0.4% of cement dust still adheres on the quartz sand bed after 5 min of cleaning cycle. The presence of 0.4% of pre-load dust on the quartz sand filter enhanced the efficiency and low initial penetration, moderate initial pressure drop was obtained. At given Empty Bed Contact Time (EBCT, with different filter diameters 30 and 15 cm, a sharp decrease in initial penetration from 0.41-0.03 was obtained respectively. A nonlinear relationship between penetration and temperature was found. The initial penetration can be reduced by using smaller filter diameter, small collector size and collector with pre-load dust with 0.4%. The experiment that operates at a filter diameter of 15 cm and temperature of 25°C represent the minimum penetration among all the experiments.

  20. Pulsatory characteristics of wind velocity in sand flow over typical underlying surfaces

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Pulsatory characteristics of wind velocity in sand flow over Gobi and mobile sand surface have been investigated experimentally in the wind tunnel. The primary goal of this paper is to reveal the relation- ship between pulsatory characteristics of instantaneous wind speed in sand flow and the motion state of sand grains. For a given underlying surface, pulsation of wind velocities in sand flow on different heights has a good correlation. As the space distance among different heights increases, fluctuation of instantaneous wind speed presents a decreasing trend and its amplitude is closely related to the mo- tion state of sand grains and their transport. Pulsatory intensity increases with the indicated wind speed, but its relative value does not depend on it, only agrees with height.

  1. Sand dollar sites orogenesis

    Science.gov (United States)

    Amos, Dee

    2013-04-01

    The determinology of the humble sand dollars habitat changing from inception to the drastic evolution of the zone to that of present day. Into the cauldron along the southern Californian 'ring of fire' lithosphere are evidence of geosynclinals areas, metasedimentary rock formations and hydrothermal activity. The explanation begins with 'Theia' and the Moon's formation, battles with cometary impacts, glacial ages, epochs with evolutionary bottlenecks and plate tectonics. Fully illustrated the lecture includes localised diagrams and figures with actual subject photographic examples of plutonic, granitic, jade and peridodite. Finally, the origins of the materials used in the lecture are revealed for prosecution by future students and the enjoyment of interested parties in general.

  2. Sand Storms Trigger Alarm

    Institute of Scientific and Technical Information of China (English)

    LI LI

    2010-01-01

    @@ After an unusually humid winter with at least 10 snowfalls in Beijing, a severe andstorm blown by strong winds bringing with it thousands of tons of desert sand took many residents of the city by surprise.On the morning of March 20, Beijingers woke up to see clouds of yellow dust in the air and a sky that was an ominous orange in color.The loose soil and dust that had traveled htmdreds of miles from deserts in Mongolia and China's northwest blanketed Beijing's streets, covering parked vehicles, bikes, roofs and even plant life,as well as making its way into people's homes.

  3. Fortune Cookie Sand Dunes

    Science.gov (United States)

    2003-01-01

    MGS MOC Release No. MOC2-432, 25 July 2003This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a field of small barchan sand dunes in the north polar region near 71.7oN, 51.3oW. Some of them are shaped like fortune cookies. The message these dunes provide: winds blow through this region from the lower right toward the upper left. The steep slip face slopes of these dunes, which point toward the upper left, indicate the wind direction. The scene is illuminated by sunlight from the upper right. The image is 3 km (1.9 mi) wide.

  4. A family of sand automata

    CERN Document Server

    Faulkner, Nicholas

    2012-01-01

    We study some dynamical properties of a family of two-dimensional cellular automata: those that arise from an underlying one dimensional sand automaton whose local rule is obtained using a latin square. We identify a simple sand automaton G whose local rule is algebraic, and classify this automaton as having equicontinuity points, but not being equicontinuous. We also show it is not surjective. We generalise some of these results to a wider class of sand automata.

  5. Dilatometric Characterization of Foundry Sands

    Directory of Open Access Journals (Sweden)

    M. Břuska

    2012-04-01

    Full Text Available The goal of this contribution is summary of physical – chemistry properties of usually used foundry silica and no – silica sands in Czech foundries. With the help of dilatometry analysis theoretical assumptions of influence of grain shape and size on dilatation value of sands were confirmed. Determined was the possibility of dilatometry analysis employment for preparing special (hybrid sands with lower and/or more linear character of dilatation.

  6. Laboratory studies of dune sand for the use of construction industry in Sri Lanka

    Science.gov (United States)

    de Silva Jayawardena, Upali; Wijesuriya, Roshan; Abayaweera, Gayan; Viduranga, Tharaka

    2015-04-01

    With the increase of the annual sand demand for the construction industry the excessive excavation of river sand is becoming a serious environmental problem in Sri Lanka. Therefore, it is necessary to explore the possibility for an alternative to stop or at least to minimize river sand mining activities. Dune sand is one of the available alternative materials to be considered instead of river sand in the country. Large quantities of sand dunes occur mainly along the NW and SE coastal belt which belong to very low rainfall Dry Zone coasts. The height of dune deposits, vary from 1m to about 30 meters above sea level. The objective of this paper is to indicate some studies and facts on the dune sand deposits of Sri Lanka. Laboratory studies were carried out for visual observations and physical properties at the initial stage and then a number of tests were carried out according to ASTM standards to obtain the compressive strength of concrete cylinders and mortar cubes mixing dune sand and river sand in different percentages keeping a constant water cement ratio. Next the water cement ratio was changed for constant dune sand and river sand proportion. Microscopic analysis shows that the dune sand consist of 95 % of quartz and 5 % of garnet, feldspar, illmenite and other heavy minerals with clay, fine dust, fine shell fragments and organic matters. Grains are sub-rounded to angular and tabular shapes. The grain sizes vary from fine to medium size of sand with silt. The degree of sorting and particle size observed with dune sands are more suited with the requirement of fine aggregates in the construction industry. The test result indicates that dune sand could be effectively used in construction work without sieving and it is ideal for wall plastering due to its'-uniformity. It could also be effectively used in concrete and in mortars mixing with river sand. The best mixing ratio is 75% dune sand and 25% river sand as the fine aggregate of concrete. For mortar the mixing

  7. Fresh groundwater resources in a large sand replenishment

    Science.gov (United States)

    Huizer, Sebastian; Oude Essink, Gualbert H. P.; Bierkens, Marc F. P.

    2016-08-01

    The anticipation of sea-level rise and increases in extreme weather conditions has led to the initiation of an innovative coastal management project called the Sand Engine. In this pilot project a large volume of sand (21.5 million m3) - also called sand replenishment or nourishment - was placed on the Dutch coast. The intention is that the sand is redistributed by wind, current, and tide, reinforcing local coastal defence structures and leading to a unique, dynamic environment. In this study we investigated the potential effect of the long-term morphological evolution of the large sand replenishment and climate change on fresh groundwater resources. The potential effects on the local groundwater system were quantified with a calibrated three-dimensional (3-D) groundwater model, in which both variable-density groundwater flow and salt transport were simulated. Model simulations showed that the long-term morphological evolution of the Sand Engine results in a substantial growth of fresh groundwater resources, in all adopted climate change scenarios. Thus, the application of a local sand replenishment could provide coastal areas the opportunity to combine coastal protection with an increase of the local fresh groundwater availability.

  8. Isotropic Compression Behaviour of Fibre Reinforced Cemented Sand

    Directory of Open Access Journals (Sweden)

    Salahuddin

    2013-07-01

    Full Text Available Fibre-reinforced cemented sands have many applications in improving the response of soils. In this paper, an experimental investigation for the analysis of fiber-reinforced cemented sand in the framework of isotropic compression is presented. The experimental investigations were carried out using a high pressure triaxial apparatus having the capacity of 64 MPa of confining pressure. Tests have been conducted on Portaway sand specimens reinforced with randomly oriented discrete polypropylene fibers with different percentages of fiber and cement contents. Results are presented in the form of e-logp` curves as well as SEM (Scanning Electron Microscopy micrographs. The effects of the addition of fibre in sand and cemented sand for different initial void ratios were investigated. The results demonstrate that the influence of fibre is not significant in both cemented and uncemented sand during the isotropic compression stage. Moreover, from the SEM micrographs it could be seen that there is breakage of sand particles and cement bonds. The fiber threads were seen pinched and found rarely broken in the specimen exhumed after isotropic compression.

  9. Layers, Landslides, and Sand Dunes

    Science.gov (United States)

    2003-01-01

    [figure removed for brevity, see original site] Released 27 October 2003This image shows the northern rim of one of the Valles Marineris canyons. Careful inspection shows many interesting features here. Note that the spurs and gullies in the canyon wall disappear some distance below the top of the canyon wall, indicating the presence of some smooth material here that weathers differently from the underlying rocks. On the floor of the canyon, there are remains from a landslide that came hurtling down the canyon wall between two spurs. Riding over the topography of the canyon floor are many large sand dunes, migrating generally from the lower right to upper left.Image information: VIS instrument. Latitude -14.1, Longitude 306.7 East (53.3 West). 19 meter/pixel resolution.Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time. NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the prime contractor for the Odyssey project, and developed and built the orbiter. Mission operations are conducted jointly from Lockheed Martin and from JPL, a division of the California Institute of Technology in Pasadena.

  10. A sand wave simulation model

    NARCIS (Netherlands)

    Nemeth, A.A.; Hulscher, S.J.M.H.; Damme, van R.M.J.

    2003-01-01

    Sand waves form a prominent regular pattern in the offshore seabeds of sandy shallow seas. A two dimensional vertical (2DV) flow and morphological numerical model describing the behaviour of these sand waves has been developed. The model contains the 2DV shallow water equations, with a free water su

  11. Regeneration of dredged sand waves

    NARCIS (Netherlands)

    Hulscher, Suzanne J.M.H.; Knaapen, Michiel; Scholl, Olaf; Scholl, O.; Trenteseaux., A.; Garlan, T.

    2000-01-01

    Sand waves form a wavy pattern in the offshore sandy seabed. Since their crests reduce the navigability, it is important to know their evolution. A simple model is presented to estimate the recovery of sand wave amplitudes. This model is partially based on the similarity with sea ripples and

  12. Namibia : triaxial test on sand

    DEFF Research Database (Denmark)

    Steenfelt, Jørgen S.; Jacobsen, Kim P.

    In connection with a harbour project the friction angle of a fine sand is required. On Friday 13 March 1998 the Danish Geotechnical Institute (DGI) delivered app. 2.5 kg sand for testing at the Geotechnical Engineering Laboratory, Aalborg University. The present Data Report summarises the results...

  13. Dredging Research Program. Results of Monitoring the Disposal Berm at Sand Island, Alabama. Report 1. Construction and First Year’s Response

    Science.gov (United States)

    1990-12-01

    22M MOBLE AL. 3NASIO Figure 10. Recovery card attached to each SBD conventional 7-g attached weight results in near neutral buoyancy. These SBD’s move...PELICAN POINT MOBLE POINT GULF SHORES 3 MAR 87 -m 20 19MAR87 ? 17 31 MAR87 D , HQ 19z 15APR87 n- __12 cr" 5MAY87 0 15 II AUG 87 12 z 20 OCT 87 6 I DEC... Technology Laboratory, MS. Hallermeier, R. J. 1980 (Aug). "Sand Motion Initiation by Water Waves: Two Asymptotes," Journal of the Waterway. Port, Coastal and

  14. Mechanism of sand slide - cold lahar induced by extreme rainfall

    Science.gov (United States)

    Fukuoka, Hiroshi; Yamada, Masumi; Dok, Atitkagna

    2014-05-01

    reveal the mechanism of rapid motion. In the undrained or partially drained tests under pore water pressure test, monotonic loading of shear stress, and constant shear speed conditions, we found that immediately after failure takes place, a big excess pore pressure was generated and accelerating motions had stated in all cases. The reduced shear resistance thereafter was maintained because of the lasting high pore pressure. Even in the partially-drained test, we found once the pore pressure reached almost same with the normal stress and then gradually decreased due to dissipation. Those tests apparently shows that the high mobility and high acceleration of the motion are expected and this could be the key mechanism of the fluidization of initial shallow slides into sand flows, i.e., cold lahars. In the past ring shear test series on volcanic materials from fluidized landslides at El Picaccho of El Salvador, Mt Aso of Kumamto Prefecture, and Nagari Tandikat near Padang, Indonesia, show very similar trends. In all those cases, we expected serious grain crushing during shear, contributed to the generation of excess pore pressure, because those material are deposited recently (in geological time) and suffered no big overburden pressure which means no consolidation and no serious grain crushing ever before. So those volcanic materials are generally susceptible to crushing and expect high mobility when slides are initiated under fully saturated condition.

  15. Inflation and Cyclotron Motion

    CERN Document Server

    Greensite, Jeff

    2016-01-01

    We consider, in the context of a braneworld cosmology, the motion of the universe coupled to a four-form gauge field, with constant field strength, defined in higher dimensions. It is found, under rather general initial conditions, that in this situation there is a period of exponential inflation combined with cyclotron motion in the inflaton field space. The main effect of the cyclotron motion is that conditions on the flatness of the inflaton potential, which are typically necessary for exponential inflation, can be evaded. There are Landau levels associated with the four-form gauge field, and these correspond to quantum excitations of the inflaton field.

  16. Sand swimming lizard: sandfish

    CERN Document Server

    Maladen, Ryan D; Kamor, Adam; Goldman, Daniel I

    2009-01-01

    We use high-speed x-ray imaging to reveal how a small (~10cm) desert dwelling lizard, the sandfish (Scincus scincus), swims within a granular medium [1]. On the surface, the lizard uses a standard diagonal gait, but once below the surface, the organism no longer uses limbs for propulsion. Instead it propagates a large amplitude single period sinusoidal traveling wave down its body and tail to propel itself at speeds up to ~1.5 body-length/sec. Motivated by these experiments we study a numerical model of the sandfish as it swims within a validated soft sphere Molecular Dynamics granular media simulation. We use this model as a tool to understand dynamics like flow fields and forces generated as the animal swims within the granular media. [1] Maladen, R.D. and Ding, Y. and Li, C. and Goldman, D.I., Undulatory Swimming in Sand: Subsurface Locomotion of the Sandfish Lizard, Science, 325, 314, 2009

  17. 2010 oil sands performance report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    With the depletion of traditional energy resources and the rising demand for energy, oil sands have become an important energy resource for meeting energy needs. Oil sands are a mixture of water, sand, clay and bitumen which is recovered either through open pit mining or in situ drilling techniques. The bitumen is then converted into syncrude or sold to refineries for the production of gasoline, diesel or other products. Shell has oil sands operations in Alberta and the aim of this report is to present its 2010 performance in terms of CO2, water, tailings, land, and reclamation and engagement. This document covers several of Shell's operations in the Muskeg River and Jackpine mines, Scotford upgrader, Peace River, Orion, Seal, Cliffdale and Chipmunk. It provides useful information on Shell's oil sands performance to governments, environmental groups, First Nations, local communities and the public.

  18. The cone penetration test in unsaturated silty sands

    Directory of Open Access Journals (Sweden)

    Yang Hongwei

    2016-01-01

    Full Text Available Very little is known about how to interpret the cone penetration test (CPT when performed in unsaturated soils. The few published studies on the CPT in unsaturated soils have focused on either clean sands or a silt. In this study new results of laboratory-controlled CPTs in an unsaturated silty sand are presented. The silty sand exhibits hydraulic hysteresis and suction hardening. Suction is observed to have a pronounced affect on measured cone penetration resistance. For an isotropic net confining stress of 60 kPa it is observed that higher suctions give rise to cone penetration resistances that are 50% larger than those for lower suctions. A semi-theoretical correlation is presented that links measured cone penetration resistances to initial relative density and mean effective stress. For this silty sand it is shown that failing to account for suction may result in significant overestimations and unsafe predictions of soil properties from measured cone penetration resistances.

  19. Sand harm in taklimakan Desert highway and sand control

    Institute of Scientific and Technical Information of China (English)

    HANZhiwen; WANGTao; SUNQingwei; DONGZhibao; WANGXunming

    2003-01-01

    Reputed as a wonderful achievement of the world’s highway construction history,the Taklimakan Desert highway is nor facing serious sand drift encroachment problems due to its 447-km-long passage of sand sea consisting of crescent dunes,barchan chains,compound transverse dune ridges and complex megadunes.To solve some technical problems in the protection of the highway from sang drift encroachment,desert experts have been conducting the theoretical and applied studies on sand movement laws;causes,severities and time-space differentiation of sand drift damages;and control ways including mechanical,chemical and biological measures.In this paper the authors give an overall summry on the research contents and recent progress in the control of sand drift damages in China and hold that the theoretical researc results and practices in the prevention of sand drift encroachment on the cross-desert highway represnt a breakthrough and has an cpoch-making significance.Since the construction of protective forest along the cross-desert highway requires large amount of ground water,what will be its environmental consequence and whether it can effectively halt sand drift encroachment on the highway forever are the questions to be studied urgently.

  20. Monitoring and characterisation of sand-mud sedimentation processes

    Science.gov (United States)

    Cuthbertson, Alan J. S.; Ibikunle, Olugbenga; McCarter, W. John; Starrs, Gerard

    2016-07-01

    Estuaries and tidal inlets are often characterised by the presence of both cohesive and non-cohesive sediments. Knowledge of the sedimentation behaviour of sand-mud mixtures is therefore crucial to the understanding and prediction of the time-dependent structure (i.e. mixed or segregated), composition and erodibility of sediment bed deposits developing within these environments. In the current study, a series of settling column tests are conducted to investigate the hindered settling and initial bed consolidation phases of a range of sand-clay mixtures to determine the parametric conditions under which bed segregation occurs. A new, non-invasive, electrical resistivity measurement technique is employed to capture both temporal and spatial changes in the density, porosity and composition of the evolving sand-clay bed deposits, complimented by time-lapsed images of the sedimentation process within the column. The results show that the formation of segregated (sand-clay) bed layers with bed deposits is largely controlled by the initial fractional composition (i.e. relative sand and clay concentrations). Specifically, mixtures with low clay contents are shown to form well-defined (sand-clay) layer segregation within the resulting deposits, while higher clay contents result in more transitional segregation patterns or no layer segregation (for very high clay concentrations). The physical mechanisms under which these different segregation types can be generated are illustrated through predictions from an existing polydisperse hindered settling model. This model indicates that the degree of bed segregation, and time scale over which this occurs, correlates well with the difference in predicted hindered settling characteristics and upward displacements associated with the sand and clay fractions, respectively. In this regard, the new experimental dataset provides validation for the polydisperse model (for the first time), with the combined data and model predictions

  1. Fractional motions

    Energy Technology Data Exchange (ETDEWEB)

    Eliazar, Iddo I., E-mail: eliazar@post.tau.ac.il [Holon Institute of Technology, P.O. Box 305, Holon 58102 (Israel); Shlesinger, Michael F., E-mail: mike.shlesinger@navy.mil [Office of Naval Research, Code 30, 875 N. Randolph St., Arlington, VA 22203 (United States)

    2013-06-10

    Brownian motion is the archetypal model for random transport processes in science and engineering. Brownian motion displays neither wild fluctuations (the “Noah effect”), nor long-range correlations (the “Joseph effect”). The quintessential model for processes displaying the Noah effect is Lévy motion, the quintessential model for processes displaying the Joseph effect is fractional Brownian motion, and the prototypical model for processes displaying both the Noah and Joseph effects is fractional Lévy motion. In this paper we review these four random-motion models–henceforth termed “fractional motions” –via a unified physical setting that is based on Langevin’s equation, the Einstein–Smoluchowski paradigm, and stochastic scaling limits. The unified setting explains the universal macroscopic emergence of fractional motions, and predicts–according to microscopic-level details–which of the four fractional motions will emerge on the macroscopic level. The statistical properties of fractional motions are classified and parametrized by two exponents—a “Noah exponent” governing their fluctuations, and a “Joseph exponent” governing their dispersions and correlations. This self-contained review provides a concise and cohesive introduction to fractional motions.

  2. The Rheology of Acoustically Fluidized Sand

    Science.gov (United States)

    Conrad, J. W.; Melosh, J.

    2013-12-01

    The collapse of large craters and the formation of central peaks and peak rings is well modeled by numerical computer codes that incorporate the acoustic fluidization mechanism to temporarily allow the fluid-like flow of rock debris immediately after crater excavation. Furthermore, long runout landslides require a similar mechanism to explain their almost frictionless movement, which is probably also a consequence of their granular composition coupled with internal vibrations. Many different investigators have now confirmed the ability of vibrations to fluidize granular materials. Yet it still remains to fully describe the rheology of vibrated sand as a function of stress, frequency and amplitude of the vibrations in the sand itself. We constructed a rotational viscometer to quantitatively investigate the relation between the stress and strain rate in a horizontal bed of strongly vibrated sand. In addition to the macroscopic stain rate, the amplitude and frequency of the vibrations produced by a pair of pneumatic vibrators were also measured with the aid of miniaturized piezoelectric accelerometers (B&K 4393) whose output was recorded on a digital storage oscilloscope. The initial gathering of the experimental data was difficult due to granular memory, but by having the sand compacted vibrationally for 8 minutes before each run the scatter of data was reduced and we were able to obtain consistent results. Nevertheless, our major source of uncertainty was variations in strain rate from run to run. We find that vibrated sand flows like a highly non-Newtonian fluid, in which the shear strain rate is proportional to stress to a power much greater than one, where the precise power depends on the amplitude and frequency of the applied vibrations. Rapid flow occurs at stresses less than half of the static yield stress (that is, the yield stress when no vibration is applied) when strong vibrations are present. For a Newtonian fluid, such as water, the relation between

  3. DYNAMIC EFFECTIVE SHEAR STRENGTH OF SATURATED SAND

    Institute of Scientific and Technical Information of China (English)

    邵生俊; 谢定义

    2002-01-01

    The dynamic effective shear strength of saturated sand under cyclic loading is discussed in this paper. The discussion includes the transient time dependency behaviors based on the analysis of the results obtained in conventional cyclic triaxial tests and cyclic torsional shear triaxial tests. It has been found that the dynamic effective shear strength is composed of effective frictional resistance and viscous resistance, which are characterized by the strain rate dependent feature of strength magnitude, the coupling of consolidation stress with cyclic stress and the dependency of time needed to make the soil strength suffciently mobilized, and can also be expressed by the extended Mohr-Coulomb's law. The two strength parameters of the dynamic effective internal frictional angle φd and the dynamic viscosity coefficient η are determined. The former is unvaried for different number of cyclic loading, dynamic stress form and consolidation stress ratio. And the later is unvaried for the different dynamic shear strain rate γt developed during the sand liquefaction, but increases with the increase of initial density of sand. The generalization of dynamic effective stress strength criterion in the 3-dimensional effective stress space is studied in detail for the purpose of its practical use.

  4. Sand engine quells the coast's hunger for sand

    NARCIS (Netherlands)

    Van Dijk, T.

    2012-01-01

    An artificial peninsula at Ter Heijde is designed to feed the coast with sediment. Scientists are investigating whether this kind of sand engine could be the Netherlands’ answer to rising sea levels.

  5. Sand engine quells the coast's hunger for sand

    NARCIS (Netherlands)

    Van Dijk, T.

    2012-01-01

    An artificial peninsula at Ter Heijde is designed to feed the coast with sediment. Scientists are investigating whether this kind of sand engine could be the Netherlands’ answer to rising sea levels.

  6. Spectroscopic characterization of a Nigerian standard sand: Igbokoda sand

    CSIR Research Space (South Africa)

    Ojuri, OO

    2017-01-01

    Full Text Available the Middle Ordovician St. Peter Sandstone near Ottawa, Illinois, had been picked by the American Society for Testing and Materials (ASTM) as the reference sand to employ in testing cement and strength of concrete [9]. To the best of our knowledge... and magnetic resonance spectroscopic techniques due to its importance in cement, geotechnical/geo-environmental research in Nigeria. This should halt importation of standard silica sand for mortar and concrete testing...

  7. Athabasca oil sands development : lessening the footprint

    Energy Technology Data Exchange (ETDEWEB)

    Dyer, R. [Alberta Environment, AB (Canada)

    2005-07-01

    This presentation provided an overview of the oil sands development footprint from the perspectives of industry, environmental associations and regulatory agencies. A map of regional oil sands developments was presented along with details of land disturbance to date. Industry strategies for lessening the impact of land disturbance include compact space-efficient mining operations; good planning; and effective, progressive reclamation. A closure and reclamation model was presented, along with key reclamation challenges such as overburden. Issues concerning tailings sands were examined. Details of Syncrude's closure vision were presented, including details of the Mildred Lake site. Details of the Fort McMurray Environmental Association were presented as well as various regional multi-stakeholder initiatives. A background of Syncrude and Suncor operations was presented as well as development projection forecasts. Impacts to the Boreal region were examined. Details of land reclamation by Syncrude were provided, as well as a chart of cumulative disturbances. It was noted that recent applications have indicated numerous reclamation uncertainties, including long-term performance of landforms and the feasibility of developing trafficable tailings landforms. It was suggested that the ecosystem dynamics of the Boreal are poorly understood. Exacerbating factors include the degraded state of soils; viability of end pit lakes; and climate change. It was suggested that operators are proposing to deal with landscape and technology uncertainty using adaptive management strategies. Government responses to the oil sand development footprint include the encouragement of more research into tailings technologies, end pit lake viability and reclamation; and the identification of regional landscape ecological thresholds by the Cumulative Environmental Management Association (CEMA). It was concluded that uncertainty needs to be addressed via a variety of policy and management options

  8. Saltation of Non-Spherical Sand Particles

    Science.gov (United States)

    Wang, Zhengshi; Ren, Shan; Huang, Ning

    2014-01-01

    Saltation is an important geological process and the primary source of atmospheric mineral dust aerosols. Unfortunately, no studies to date have been able to precisely reproduce the saltation process because of the simplified theoretical models used. For example, sand particles in most of the existing wind sand movement models are considered to be spherical, the effects of the sand shape on the structure of the wind sand flow are rarely studied, and the effect of mid-air collision is usually neglected. In fact, sand grains are rarely round in natural environments. In this paper, we first analyzed the drag coefficients, drag forces, and starting friction wind speeds of sand grains with different shapes in the saltation process, then established a sand saltation model that considers the coupling effect between wind and the sand grains, the effect of the mid-air collision of sand grains, and the effect of the sand grain shape. Based on this model, the saltation process and sand transport rate of non-spherical sand particles were simulated. The results show that the sand shape has a significant impact on the saltation process; for the same wind speed, the sand transport rates varied for different shapes of sand grains by as much as several-fold. Therefore, sand shape is one of the important factors affecting wind-sand movement. PMID:25170614

  9. Initial experience of correlating parameters of intravoxel incoherent motion and dynamic contrast-enhanced magnetic resonance imaging at 3.0 T in nasopharyngeal carcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Qian-Jun; Zhang, Shui-Xing; Chen, Wen-Bo; Liang, Long; Zhou, Zheng-Gen; Liu, Zai-Yi; Zeng, Qiong-Xin; Liang, Chang-Hong [Guangdong General Hospital/Guangdong Academy of Medical Sciences, Department of Radiology, Guangzhou, Guangdong Province (China); Qiu, Qian-Hui [Guangdong General Hospital/Guangdong Academy of Medical Sciences, Department of Otolaryngology, Guangzhou, Guangdong Province (China)

    2014-12-15

    To determine the correlation between intravoxel incoherent motion (IVIM) and dynamic contrast-enhanced (DCE) magnetic resonance imaging (MRI) parameters. Thirty-eight newly diagnosed NPC patients were prospectively enrolled. Diffusion-weighted images (DWI) at 13 b-values were acquired using a 3.0-T MRI system. IVIM parameters including the pure molecular diffusion (D), perfusion-related diffusion (D*), perfusion fraction (f), DCE-MRI parameters including maximum slope of increase (MSI), enhancement amplitude (EA) and enhancement ratio (ER) were calculated by two investigators independently. Intra- and interobserver agreement were evaluated using the intraclass correlation coefficient (ICC) and Bland-Altman analysis. Relationships between IVIM and DCE-MRI parameters were evaluated by calculation of Spearman's correlation coefficient. Intra- and interobserver reproducibility were excellent to relatively good (ICC = 0.887-0.997; narrow width of 95 % limits of agreement). The highest correlation was observed between f and EA (r = 0.633, P < 0.001), with a strong correlation between f and MSI (r = 0.598, P = 0.001). No correlation was observed between f and ER (r = -0.162; P = 0.421) or D* and DCE parameters (r = 0.125-0.307; P > 0.119). This study suggests IVIM perfusion imaging using 3.0-T MRI is feasible in NPC, and f correlates significantly with EA and MSI. (orig.)

  10. Experimental study of surface texture and resonance mechanism of booming sand

    Institute of Scientific and Technical Information of China (English)

    QU; JianJun; ZHANG; KeCun; SUN; Bo; JIANG; ShengXiang; DONG; GuangRong; ZU; RuiPing; FANG; HaiYan

    2007-01-01

    The sound-producing mechanism of booming sand has long been a pending problem in the blown sand physics. Based on the earlier researches, the authors collected some silent sand samples from Tengger Desert, Australian Desert, Kuwait Desert, beaches of Hainan Island and Japanese coast as well as the soundless booming sand samples from the Mingsha Mountain in Dunhuang to make washing experiments. In the meantime the chemical corrosion experiment of glass micro-spheres, surface coating experiment and SEM examination were also conducted. The experimental results show that the sound production of booming sand seems to have nothing to do with the presence of SiO2 gel on the surface of sand grains and unrelated to the surface chemical composition of sand grains but is related to the resonance cavities formed by porous (pit-like) physical structure resulting from a number of factors such as wind erosion, water erosion, chemical corrosion and SiO2 gel deposition, etc. Its resonance mechanism is similar to that of Hemholz resonance cavity. Under the action of external forces, numerous spherical and sand grains with smooth surface and porous surface are set in motion and rub with each other to produce extremely weak vibration sound and then become audible sound by human ears through the magnification of surface cavity resonance. However the booming sands may lose their resonance mechanism and become silent sand due to the damping action caused by the invasion of finer particles such as dust and clay into surface holes of sand grains. Therefore, clearing away fine pollutants on the quartz grain surface is an effective way to make silent sand emit audible sound.

  11. Reclaimability of the spent sand mixture – sand with bentonite – sand with furfuryl resin

    Directory of Open Access Journals (Sweden)

    J. Dańko

    2011-04-01

    Full Text Available Introduction of new binding materials and new technologies of their hardening in casting moulds and cores production requires theapplication of reclamation methods adequate to their properties as well as special devices realizing tasks. The spent sands circulationsystem containing the same kind of moulding and core sands is optimal from the point of view of the expected reclamation results.However, in the face of a significant variability of applied technologies and related to them various reclamation methods, the need - of theobtained reclamation products assessment on the grounds of systematic criteria and uniform bases – arises, with a tendency of indicatingwhich criteria are the most important for the given sand system. The reclaimability results of the mixture of the spent moulding sand withGeko S bentonite and the spent core sand with the Kaltharz 404U resin hardened by acidic hardener 100 T3, are presented in the paper.Investigations were performed with regard to the estimation of an influence of core sands additions (10 –25% on the reclaimed materialquality. Dusts and clay content in the reclaim, its chemical reaction (pH and ignition loss were estimated. The verification of the reclaiminstrumental assessment was performed on the basis of the technological properties estimation of moulding sand with bentonite, where the reclaimed material was used as a matrix.

  12. Undrained Triaxial Tests on Eastern Scheldt Sand

    DEFF Research Database (Denmark)

    Jakobsen, Kim Parsberg

    In the process of understanding and developing models for geomaterials, the stress-strain behaviour is commonly studied by performing triaxial tests. In the present study, several types of static triaxial tests have been performed to gain knowledge of the undrained stress-strain behaviour...... of frictional materials during monotonic loading. The tests conducted includes undrained and constant volume tests, starting from different initial states of stress and following various stress paths. All the tests are performed on reconstituted loose to medium dense specimens of Eastern Scheldt Sand....

  13. Sand Fences in the Coastal Zone: Intended and Unintended Effects

    Science.gov (United States)

    Grafals-Soto, Rosana; Nordstrom, Karl

    2009-09-01

    Sand-trapping fences modify the character of the coastal landscape and change its spatial structure, image, and meaning. This paper examines the relationship between these changes and fence usage at the municipal level, where most decisions about fence deployment are made. Use of fences in 29 municipalities on the developed coast of New Jersey is examined over a 6-year period. Interviews with municipal officers indicate that wooden slat sand-trapping fences are used primarily to build dunes to provide protection against wave uprush and flooding, but they are also used to control pedestrian traffic and demarcate territory. These uses result in changes in landforms and habitats. An aerial video inventory of fences taken in 2002 indicates that 82% of the shoreline had fences and 72% had dunes. Single and double straight fence rows are the most commonly used. Fences are often built to accomplish a specific primary purpose, but they can cause many different and often unanticipated changes to the landscape. The effects of a sand fence change through time as the initial structure traps sand, creates a dune that is colonized by vegetation, and becomes integrated into the environment by increasing topographic variability and aesthetic and habitat value. Sand fences can be made more compatible with natural processes by not placing them in locations where sources of wind blown sand are restricted or in unnatural shore perpendicular orientations. Symbolic fences are less expensive, are easy to replace when damaged, are less visually intrusive, and can be used for controlling pedestrian access.

  14. Management recommendations: Sand Lake Complex

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This document is a review of land management practices at the Sand Lake National Wildlife Refuge, by a land use specialist. Recommendations, time frame and...

  15. Sustainable water management in Alberta's oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Byers, Bill; Usher, Robyn; Roach, Andrea [CH2M HILL, Englewood, CO (United States); Lambert, Gord; Kotecha, Prit [Suncor Energy Inc., Calgary (Canada)

    2012-07-01

    The Canadian Association of Petroleum Producers forecast published in 2011 predicts that oil production from oil sands will increase by 50% in the next 3 years and double by 2020. This rate of growth will result in significant pressure on water resources; water use per barrel of oil sands production is comparable to other energy resources - about 2.5 barrels of fresh water per barrel of oil produced are used by mining operations and 0.5 barrels by in-situ operations. Suncor Energy Inc. (Suncor) was the first company to develop the oil sands in northern Alberta and holds one of the largest oil sands positions in Canada. In 2010, Suncor announced plans to increase production to more than 1 million barrels of oil equivalent per day by 2020, which it plans to achieve through oil sands production growth of approximately 10% per year. Because water supply and potential impacts to water quality are critical to its future growth, in 2010-2011 Suncor conducted a risk assessment to identify water-related business risks related to its northern Alberta operations. The assessment identified more than 20 high level business risks in strategic water risk areas including water supply, water reuse, storm water management, groundwater, waste management and river water return. The risk assessment results prompted development of a strategic roadmap to guide water stewardship across Suncor's regional operations. The roadmap describes goals, objectives, and specific activities for each of six key water risk areas, and informs prioritization and selection of prospective water management activities. Suncor is not only exploring water within its own boundaries, but is also collaborating with other oil sands producers to explore ways of integrating its water systems through industry consortia; Suncor is a member of the Oil Sands Leadership Initiative and of the recently formed Canadian Oil Sands Innovation Alliance, among others. (author)

  16. Performance of sand and shredded rubber tire mixture as a natural base isolator for earthquake protection

    Science.gov (United States)

    Bandyopadhyay, Srijit; Sengupta, Aniruddha; Reddy, G. R.

    2015-12-01

    The performance of a well-designed layer of sand, and composites like layer of sand mixed with shredded rubber tire (RSM) as low cost base isolators, is studied in shake table tests in the laboratory. The building foundation is modeled by a 200 mm by 200 mm and 40 mm thick rigid plexi-glass block. The block is placed in the middle of a 1m by 1m tank filled with sand. The selected base isolator is placed between the block and the sand foundation. Accelerometers are placed on top of the footing and foundation sand layer. The displacement of the footing is also measured by LVDT. The whole setup is mounted on a shake table and subjected to sinusoidal motions with varying amplitude and frequency. Sand is found to be effective only at very high amplitude (> 0.65 g) of motions. The performance of a composite consisting of sand and 50% shredded rubber tire placed under the footing is found to be most promising as a low-cost effective base isolator.

  17. The influence of storms on finite amplitude sand wave dynamics: an idealized nonlinear model

    NARCIS (Netherlands)

    Campmans, G.H.P.; Roos, P.C.; de Vriend, H.J.; Hulscher, S.J.M.H.

    2017-01-01

    We investigate the effects of storms on finite amplitude sand wave growth using a new idealized nonlinear morphodynamic model. We find that the growth speed initially linearly increases with sand wave amplitude, after which nonlinear effects cause the growth to decrease. This finally leads to an

  18. Processes of microbial pesticide degradation in rapid sand filters for treatment of drinking water

    DEFF Research Database (Denmark)

    Hedegaard, Mathilde Jørgensen; Albrechtsen, Hans-Jørgen

    concentrations of 0.04-2.4 μg/L. The pesticides were removed from the water in microcosms with filter sand from all three investigated sand filters. Within the experimental periode of six to 13 days, 65-85% of the bentazone, 86-93% of the glyphosate, 97-99% of the p-nitrophenol was removed from the water phase......Aerobic rapid sand filters for treatment of groundwater at waterworks were investigated for the ability to remove pesticides. The potential, kinetics and mechanisms of microbial pesticide removal was investigated in microcosms consisting of filter sand, treated water and pesticides in initial...

  19. Experimental Investigation of Evaporation and Drainage in Wettable and Water-Repellent Sands

    Directory of Open Access Journals (Sweden)

    Dae Hyun Kim

    2015-05-01

    Full Text Available This study presents experimental results on evaporation and drainage in both wettable and water-repellent sands whose surface wettability was artificially modified by silanization. The 2D optical and 3D X-ray computed tomographic imaging was performed during evaporation and the water retention during cyclic drainage and infiltration was measured to assess effects of wettability and initial wetting conditions. The evaporation gradually induces its front at the early stage advance regardless of the wettability and sand types, while its rate becomes higher in water-repellent Ottawa sand than the wettable one. Jumunjin sand which has a smaller particle size and irregular particle shape than Ottawa sand exhibits a similar evaporation rate independent of wettability. Water-repellent sand can facilitate the evaporation when both wettable and water-repellent sands are naturally in contact with each other. The 3D X-ray imaging reveals that the hydraulically connected water films in wettable sands facilitate the propagation of the evaporation front into the soil such that the drying front deeply advances into the soil. For cyclic drainage-infiltration testing, the evolution of water retention is similar in both wettable and water-repellent sands when both are initially wet. However, when conditions are initially dry, water-repellent sands exhibit low residual saturation values. The experimental observations made from this study propose that the surface wettability may not be a sole factor while the degree of water-repellency, type of sands, and initial wetting condition are predominant when assessing evaporation and drainage behaviors.

  20. Western Gas Sands Project status report

    Energy Technology Data Exchange (ETDEWEB)

    Atkinson, C.H.

    1978-11-30

    Progress of government-sponsored projects directed toward increasing gas production from the low-permeability gas sands of the western United States is summarized. A Technology Implementation Plan (TIP) meeting was held at the CER office in Las Vegas, Nevada, October 16--19 to initiate the implementation phase of the Enhanced Gas Recovery (EGR) working group activities. A WGSP Logging Program meeting was conducted on October 24, 1978, at CER offices to define the problems associated with logs in tight gas sands. CER personnel and the project manager attended a two-day course on the fundamentals of core and reservoir analysis in Denver, Colorado, and met with USGS personnel to discuss USGS work on the WGSP. A meeting was held to discuss a contract for coring a Twin Arrow well on the Douglas Creek Arch, Colorado. CER Corporation personnel attended the Geological Society of America Annual Meeting held in Toronto, Canada, October 23--27 and a Gas Stimulation Workshop at Sandia Laboratories in Albuquerque, New Mexico, October 11 and 12 to discuss recent mineback experiments conducted at the Nevada Test Site. Fiscal year 1979 projects initiated by USGS and the Energy Technology Centers and National Laboratories are progressing as scheduled. Mobil Research and Development Corporation fractured zone 8 of the F-31-13G well in Rio Blanco County, Colorado. Colorado Interstate Gas Company poured the concrete pad for the compresser expected to be delivered in December and were laying pipeline between the wells at month end. The Mitchell Energy well, Muse Duke No. 1 was flowing on test at a rate of 2,100 Mcfd and preparations proceeded to fracture the well on November 15 with approximately 1,000,000 gal of fluid and 3,000,000 lb of sand. Terra Tek completed laboratory analyses of cores taken from the Mitchell Energy well.

  1. Documenting the global impacts of beach sand mining

    Science.gov (United States)

    Young, R.; Griffith, A.

    2009-04-01

    For centuries, beach sand has been mined for use as aggregate in concrete, for heavy minerals, and for construction fill. The global extent and impact of this phenomenon has gone relatively unnoticed by academics, NGOs, and major news sources. Most reports of sand mining activities are found at the very local scale (if the mining is ever documented at all). Yet, sand mining in many localities has resulted in the complete destruction of beach (and related) ecosystems along with severe impacts to coastal protection and tourism. The Program for the Study of Developed Shorelines at Western Carolina University and Beachcare.org have initiated the construction of a global database of beach sand mining activities. The database is being built through a combination of site visits and through the data mining of media resources, peer reviewed papers, and reports from private and governmental entities. Currently, we have documented sand mining in 35 countries on 6 continents representing the removal of millions of cubic meters of sand. Problems extend from Asia where critical infrastructure has been disrupted by sand mining to the Caribbean where policy reform has swiftly followed a highly publicized theft of sand. The Program for the Study of Developed Shorelines recently observed extensive sand mining in Morocco at the regional scale. Tens of kilometers of beach have been stripped of sand and the mining continues southward reducing hope of a thriving tourism-based economy. Problems caused by beach sand mining include: destruction of natural beaches and the ecosystems they protect (e.g. dunes, wetlands), habitat loss for globally important species (e.g. turtles, shorebirds), destruction of nearshore marine ecosystems, increased shoreline erosion rates, reduced protection from storms, tsunamis, and wave events, and economic losses through tourist abandonment and loss of coastal aesthetics. The threats posed by sand mining are made even more critical given the prospect of a

  2. On Sand or Rock.

    Science.gov (United States)

    Bentley, Norma E.

    Future teachers of English at the college level should initially be allowed to discuss and consider some of the important facts of this decade: the dwindling resources of our planet, overpopulation, hunger and disease, and the increase in global communication. They should be informed about the small number of job openings at present in the field…

  3. Projectile Motion in Special Relativity.

    Science.gov (United States)

    Naddy, Cory J.; Dudley, Scott C.; Haaland, Ryan K.

    2000-01-01

    Explains the motion that occurs when a particle with an initial velocity to the right is acted upon by a constant downward force. Considers what happens when the speed of the particle approaches the speed of light in particular. (WRM)

  4. Optimal array of sand fences.

    Science.gov (United States)

    Lima, Izael A; Araújo, Ascânio D; Parteli, Eric J R; Andrade, José S; Herrmann, Hans J

    2017-03-24

    Sand fences are widely applied to prevent soil erosion by wind in areas affected by desertification. Sand fences also provide a way to reduce the emission rate of dust particles, which is triggered mainly by the impacts of wind-blown sand grains onto the soil and affects the Earth's climate. Many different types of fence have been designed and their effects on the sediment transport dynamics studied since many years. However, the search for the optimal array of fences has remained largely an empirical task. In order to achieve maximal soil protection using the minimal amount of fence material, a quantitative understanding of the flow profile over the relief encompassing the area to be protected including all employed fences is required. Here we use Computational Fluid Dynamics to calculate the average turbulent airflow through an array of fences as a function of the porosity, spacing and height of the fences. Specifically, we investigate the factors controlling the fraction of soil area over which the basal average wind shear velocity drops below the threshold for sand transport when the fences are applied. We introduce a cost function, given by the amount of material necessary to construct the fences. We find that, for typical sand-moving wind velocities, the optimal fence height (which minimizes this cost function) is around 50 cm, while using fences of height around 1.25 m leads to maximal cost.

  5. Holocene beach buildup and coastal aeolian sand incursions off the Nile littoral cell

    Science.gov (United States)

    Roskin, Joel; Sivan, Dorit; Shtienberg, Gilad; Porat, Naomi; Bookman, Revital

    2017-04-01

    Israel's coastal plain is abundant with sand originating from the Nile littoral cell. The inland windblown loose sand has formed 3-6 km wide lobe-like sand and dune fields currently comprised of foredunes, linear and northeasterly facing transverse and parabolic dunes that are currently stabilized by vegetation. This study reviews the architecture and history of the these dune fields aiming to: (a) Date the timings of beach accretion, and sand and dune incursions. (b) Discriminate between natural and human-induced forcing factors of sand mobilization and stabilization in time and space. (c) Present a model of the dunescape development. (d) Assess scenarios of sand transport in the future charcaterized by intense human impact and climate change. Luminescence ages, radiocarbon dates and relative ages from previously published geological and archaeological reports, historical texts, together with new optically stimulated luminescence (OSL) ages and stratigraphic and sedimentological data are analyzed. The deposition, mobilizations and preservation of the sand bodies, initially induced by the decline in sea level rise at 6-4 ka, were later controlled by historic land-use intensity and modern land-use/negligence practices. At 6 ka, beach sand buildup rapidly started. Where aeolianite ridges bordered the coast, pulses of sand with biogenic carbonate grains unconformably draped the ridges and rapidly consolidated into a distinct sandy calcarenite unit. Further east, sand sheets and low dunes partly pedogenized following their incursion, but did not cement. The water retention capacities of the sand sheets enabled the establishment of a sand-stabilizing vegetation cover that probably became an attractive environment for fuel and grazing. The growing Hellenistic-Roman-Byzantine ( 2.4-1.3 ka) populations probably led to increased consumption and massive destruction of sand stabilizing vegetation, enabling sand erodibility and mobilization during winter storms. The sand

  6. Engineering knowledge requirements for sand and dust on Mars

    Science.gov (United States)

    Kaplan, D. I.

    1991-01-01

    The successful landing of human beings on Mars and the establishment of a permanent outpost there will require an understanding of the Martian environment by the engineers. A key feature of the Martian environment is the nearly ubiquitous presence of sand and dust. The process which the engineering community will undertake to determine the sensitivities of their designs to the current level of knowledge about Mars sand and dust is emphasized. The interaction of the engineering community with the space exploration initiative (SEI) mission planners and management is described.

  7. Western Gas Sands Project: stratigrapy of the Piceance Basin

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, S. (comp.)

    1980-08-01

    The Western Gas Sands Project Core Program was initiated by US DOE to investigate various low permeability, gas bearing sandstones. Research to gain a better geological understanding of these sandstones and improve evaluation and stimulation techniques is being conducted. Tight gas sands are located in several mid-continent and western basins. This report deals with the Piceance Basin in northwestern Colorado. This discussion is an attempt to provide a general overview of the Piceance Basin stratigraphy and to be a useful reference of stratigraphic units and accompanying descriptions.

  8. Sands at Gusev Crater, Mars

    Science.gov (United States)

    Cabrol, Nathalie A.; Herkenhoff, Kenneth E.; Knoll, Andrew H.; Farmer, Jack D.; Arvidson, Raymond E.; Grin, E.A.; Li, Ron; Fenton, Lori; Cohen, B.; Bell, J.F.; Yingst, R. Aileen

    2014-01-01

    Processes, environments, and the energy associated with the transport and deposition of sand at Gusev Crater are characterized at the microscopic scale through the comparison of statistical moments for particle size and shape distributions. Bivariate and factor analyses define distinct textural groups at 51 sites along the traverse completed by the Spirit rover as it crossed the plains and went into the Columbia Hills. Fine-to-medium sand is ubiquitous in ripples and wind drifts. Most distributions show excess fine material, consistent with a predominance of wind erosion over the last 3.8 billion years. Negative skewness at West Valley is explained by the removal of fine sand during active erosion, or alternatively, by excess accumulation of coarse sand from a local source. The coarse to very coarse sand particles of ripple armors in the basaltic plains have a unique combination of size and shape. Their distribution display significant changes in their statistical moments within the ~400 m that separate the Columbia Memorial Station from Bonneville Crater. Results are consistent with aeolian and/or impact deposition, while the elongated and rounded shape of the grains forming the ripples, as well as their direction of origin, could point to Ma'adim Vallis as a possible source. For smaller particles on the traverse, our findings confirm that aeolian processes have dominated over impact and other processes to produce sands with the observed size and shape patterns across a spectrum of geologic (e.g., ripples and plains soils) and aerographic settings (e.g., wind shadows).

  9. Experimental investigation on heat transport in gravel-sand materials

    DEFF Research Database (Denmark)

    Maureschat, Gerald; Heller, Alfred

    1997-01-01

    out in a small size experiment. The experiment consists of a highly insulated box filled with two kinds of sand material crossed by a plastic heat pipe. Heat transfer is measured under dry and water satured conditions in a cross-section.The conclusions are clear. To obtain necessary heat conduction......The project is a basic study on the expected thermal behaviour of gravel storage initiated as a part of a research and demonstration gravel storage for seasonal heat storage.The goal of the investigation is to determine the heat transfer between heat pipes and sand-gravel storage media by carrying...... media no convectional heat transport is found. It would be relevant to extend the investigation to media that enables convectional heat transport. A last conclusion is that such experiments, necessary for proper designing of sand-gravel storage types, are a very cheap form of collecting information...

  10. Enhanced microbubbles assisted cleaning of diesel contaminated sand.

    Science.gov (United States)

    Agarwal, Ashutosh; Liu, Yu

    2017-07-25

    In this article, we investigated the effect of low intensity pulsed ultrasound (US), temperature and salinity on cleaning efficacy of fine bubbles with diameter <50μm for diesel contaminated sands. About 47% and 76% diesel removal was achieved from 10% (w/w) diesel contaminated fine and medium sands respectively, after 30min treatment with 40kHz low intensity intermittent pulsed US together with MBs in contrast to 41% and 68% diesel removal while treatment with MBs alone. The effect of high temperature was found to be prominent during the initial stages of cleaning. In addition, MBs generated in 599mM saline water efficiently removed 85% diesel from fine sand within 30min in contrast to only 41% diesel removal with MBs in fresh water. This study provides evidence for developing highly efficient MBs based chemical free technology for diesel contaminated sediments. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Large-eddy simulation of formation of three-dimensional aeolian sand ripples in a turbulent field

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    With the method of large-eddy simulation,the equation of spherule motion and the method of immersed boundary condition,numerical simulations of three-dimen-sional turbulent aeolian motion and the formation of sand ripples under three-di-mensional turbulent wind and the mutual actions of saltation and creeping motion were carried out. The resulting sand ripples have the form that is flat on the upwind side and steep on the leeward,which is identical to the sand ripples in nature. We also realized the self-restoration process of three-dimensional sand ripples,which shows the correctness of the method of numerical simulation and the models of saltation and creeping. Finally,We analyzed the influence of sand ripples on the three-dimensional turbulent wind field,and found that due to the appearance and development of sand ripples,in the normal direction of ground there exists stronger energy exchange,and moreover,there is close correspondence between the forms of sand ripples and the vorticity close to the ground surface.

  12. Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

    Science.gov (United States)

    Nirmala, D. B.; Raviraj, S.

    2016-06-01

    This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC) containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37) Orthogonal Arrays (OA) with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering "Nominal the better" situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

  13. A comprehensive numerical model of wind-blown sand

    CERN Document Server

    Kok, Jasper F

    2009-01-01

    Wind-blown sand, or "saltation", ejects dust aerosols into the atmosphere, creates sand dunes, and erodes geological features. We present a comprehensive numerical model of steady-state saltation that, in contrast to most previous studies, can simulate saltation over mixed soils. Our model simulates the motion of saltating particles due to gravity, fluid drag, particle spin, fluid shear, and turbulence. Moreover, the model explicitly accounts for the retardation of the wind due to drag from saltating particles. We also developed a physically-based parameterization of the ejection of surface particles by impacting saltating particles which matches experimental results. Our numerical model is the first to reproduce measurements of the wind shear velocity at the impact threshold (i.e., the lowest shear velocity for which saltation is possible) and of the aerodynamic roughness length in saltation. It also correctly predicts a wide range of other saltation processes, including profiles of the wind speed and partic...

  14. DPTM simulation of aeolian sand ripple

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Aeolian sand ripple and its time evolution are simulated by the discrete particle tracing method (DPTM) presented in this paper. The difference between this method and the current methods is that the former can consider the three main factors relevant to the formation of natural aeolian sand ripples,which are the wind-blown sand flux above the sand bed formed by lots of sand particles with different di-ameters,the particle-bed collision and after it the rebound and ejection of sand particles in the sand bed,the saltation of high-speed sand particles and the creep of low-speed sand particles,respectively. The simulated aeolian sand ripple is close to the natural sand ripple not only in basic shape and characteristic,particle size segregation and stratigraphy,but also in formation stages. In addition,three important speeds can be obtained by this method,which are the propagation speed of the saturated aeolian sand ripple and the critical frictional wind speeds of emergence and disappearance of sand ripple.

  15. DPTM simulation of aeolian sand ripple

    Institute of Scientific and Technical Information of China (English)

    ZHENG XiaoJing; BO TianLi; XIE Li

    2008-01-01

    Aeolian sand ripple and its time evolution are simulated by the discrete particle tracing method (DPTM) presented in this paper.The difference between this method and the current methods is that the former can consider the three main factors relevant to the formation of natural aeolian sand ripples, which are the wind-blown sand flux above the sand bed formed by lots of sand particles with different di-ameters, the particle-bed collision and after it the rebound and ejection of sand particles in the sand bed, the saltation of high-speed sand particles and the creep of low-speed sand particles, respectively.The simulated aeolian sand ripple is close to the natural sand ripple not only in basic shape and characteristic, particle size segregation and stratigraphy, but also in formation stages.In addition, three important speeds can be obtained by this method, which are the propagation speed of the saturated aeolian sand ripple and the critical frictional wind speeds of emergence and disappearance of sand ripple.

  16. Dry reusing and wet reclaiming of used sodium silicate sand

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Based on the characteristics of used sodium silicate sand and the different use requirements for recycled sand, "dry reusing and wet reclaiming of used sodium silicate sand" is considered as the most suitable technique for the used sand. When the recycled sand is used as support sand, the used sand is only reused by dry process including breaking, screening, dust-removal, etc., and it is not necessary that the used sand is reclaimed with strongly rubbing and scraping method, but when the recycled sand is used as facing sand (or single sand), the used sand must be reclaimed by wet method for higher removal rate of the residual binders. The characteristics and the properties of the dry reused sand are compared with the wet reclaimed sand after combining the different use requirements of support sand and facing sand (or single sand), and above the most adaptive scheme has also been validated.

  17. Sand and Water Table Play

    Science.gov (United States)

    Wallace, Ann H.; White, Mary J.; Stone, Ryan

    2010-01-01

    The authors observed preschoolers engaged at the sand and water table to determine if math could be found within their play. Wanting to understand how children interact with provided materials and what kinds of math ideas they explore during these interactions, the authors offer practical examples of how such play can promote mathematical…

  18. Sand and Water Table Play

    Science.gov (United States)

    Wallace, Ann H.; White, Mary J.; Stone, Ryan

    2010-01-01

    The authors observed preschoolers engaged at the sand and water table to determine if math could be found within their play. Wanting to understand how children interact with provided materials and what kinds of math ideas they explore during these interactions, the authors offer practical examples of how such play can promote mathematical…

  19. Impact on sand and water

    NARCIS (Netherlands)

    Bergmann, R.P.H.M.

    2007-01-01

    In this thesis we investigate the impact of a body on sand and water. When a body impacts a free surface in the inertial regime the series of events is the following: On impact material is blown away in all directions and an impact cavity forms. Due to the hydrostatic pressure from the sides the cav

  20. Silo model tests with sand

    DEFF Research Database (Denmark)

    Munch-Andersen, Jørgen

    Tests have been carried out in a large silo model with Leighton Buzzard Sand. Normal pressures and shear stresses have been measured during tests carried out with inlet and outlet geometry. The filling method is a very important parameter for the strength of the mass and thereby the pressures...

  1. An Inexpensive Mechanical Model for Projectile Motion

    Science.gov (United States)

    Kagan, David

    2011-01-01

    As experienced physicists, we see the beauty and simplicity of projectile motion. It is merely the superposition of uniform linear motion along the direction of the initial velocity vector and the downward motion due to the constant acceleration of gravity. We see the kinematic equations as just the mathematical machinery to perform the…

  2. experimental studies of sand production from unconsolidated ...

    African Journals Online (AJOL)

    ES Obe

    Production of sand during oil and gas exploration causes severe operational prob- ... duction such as risk of well failure, erosion of pipelines and surface facilities, sand separa- tion and disposal ... ment, theoretical and numerical analysis have.

  3. NUMERICAL SIMULATION OF PARTICLE SEPARATION IN AN OIL-SAND SEPARATOR

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The gathering systems of crude oil are greatly endangered by thefine sand and soil in oil. Up to now, how to separate sand from the viscid oil is still a technical problem for oil production home or abroad. Recently, Institute of Mechanics in Chinese Academy of Sciences hasdeveloped a new type of oil-sand separator, which has been applied successfully in oil field in situ. In this paper, the numerical method of vortex-stream function is used to predict the liquid-solid separating course and the efficiency for this oil-sand separator. Results show that the viscosity and particle diameter have much influence on the particle motion. The calculating separating efficiency is compared with that of experiment and indicates that this method can be used to model the complex two-phase flow in the separator.

  4. UK silica sand resources for fracking

    OpenAIRE

    Mitchell, Clive

    2013-01-01

    UK silica sand resources for fracking Clive Mitchell, Industrial Minerals Specialist, British Geological Survey, Keyworth, Nottingham, NG12 5GG Email: Silica sand is high purity quartz sand that is mainly used for glass production, as foundry sand, in horticulture, leisure and other industrial uses. One specialist use is as a ‘proppant’ to enhance oil and gas recovery. This presentation will focus on this application, particularly for shale gas recovery where it is mo...

  5. Treating tar sands formations with karsted zones

    Energy Technology Data Exchange (ETDEWEB)

    Vinegar, Harold J. (Bellaire, TX); Karanikas, John Michael (Houston, TX)

    2010-03-09

    Methods for treating a tar sands formation are described herein. The tar sands formation may have one or more karsted zones. Methods may include providing heat from one or more heaters to one or more karsted zones of the tar sands formation to mobilize fluids in the formation. At least some of the mobilized fluids may be produced from the formation.

  6. Release of Escherichia coli from Foreshore Sand and Pore Water during Intensified Wave Conditions at a Recreational Beach.

    Science.gov (United States)

    Vogel, Laura J; O'Carroll, Denis M; Edge, Thomas A; Robinson, Clare E

    2016-06-01

    Foreshore beach sands and pore water may act as a reservoir and nonpoint source of fecal indicator bacteria (FIB) to surface waters. This paper presents data collected at a fine sand beach on Lake Huron, Canada over three field events. The data show that foreshore sand erosion as wave height increases results in elevated Escherichia coli concentrations in surface water, as well as depletion of E. coli from the foreshore sand and pore water. E. coli initially attached to foreshore sand rather than initially residing in the pore water was found to be the main contributor to elevated surface water concentrations. Surface water E. coli concentrations were a function of not only wave height (and associated sand erosion) but also the time elapsed since a preceding period of high wave intensity. This finding is important for statistical regression models used to predict beach advisories. While calculations suggest that foreshore sand erosion may be the dominant mechanism for releasing E. coli to surface water during intensified wave conditions at a fine sand beach, comparative characterization of the E. coli distribution at a coarse sand-cobble beach suggests that interstitial pore water flow and discharge may be more important for coarser sand beaches.

  7. Motion of Confined Particles

    CERN Document Server

    Miller, David E

    2016-01-01

    We carry out numerical evaluations of the motion of classical particles in Minkowski Space $\\mathbb{M}^{4}$ which are confined to the inside of a bag. In particular, we analyze the structure of the paths evolving from the breaking of the dilatation symmetry, the conformal symmetry and the combination of both together. The confining forces arise directly from the corresponding nonconserved currents. We demonstrate in our evaluations that these particles under certain initial conditions move toward the interior of the bag.

  8. Global motion estimation with Gabor wavelet transform

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A novel algorithm of global motion estimation is proposed. First, through Gabor wavelet transform (GWT), a kind of energy distribution of image is obtained and checkpoints are selected according to a probability decision approach proposed. Then, the initialized motion vectors are obtained via a hierarchal block-matching based on these checkpoints.Finally, by employing a 3-parameter motion model, precise parameters of global motion are found. From the experiment, the algorithm is reliable and robust.

  9. Sand Waves. Report 1. Sand Wave Shoaling in Navigation Channels

    Science.gov (United States)

    1992-09-01

    heights range from 0.8 m in the Minas Basin, Bay of Fundy (Dalrymple 1984) to 6.0 m in the Bahia Blanca Estuary, Argentina (Aliotta and Perillo 1987...26 PART IV: SITE-SPECIFIC SAND WAVE SHOALING PROBLEMS .. ........ 30 Columbia River Navigation Channel ........ ............... .. 30 Panama ...problem location discussed in this report is at St. Andrew Bay near Panama City, Florida. A relatively short section of the jettied inlet channel requires

  10. Crater formation during raindrop impact on sand

    Science.gov (United States)

    de Jong, Rianne; Zhao, Song-Chuan; van der Meer, Devaraj

    2017-04-01

    After a raindrop impacts on a granular bed, a crater is formed as both drop and target deform. After an initial, transient, phase in which the maximum crater depth is reached, the crater broadens outwards until a final steady shape is attained. By varying the impact velocity of the drop and the packing density of the bed, we find that avalanches of grains are important in the second phase and hence affect the final crater shape. In a previous paper, we introduced an estimate of the impact energy going solely into sand deformation and here we show that both the transient and final crater diameter collapse with this quantity for various packing densities. The aspect ratio of the transient crater is however altered by changes in the packing fraction.

  11. Soil Moisture Eff ects on Sand Saltation and Dust Emission Observed over the Horqin Sandy Land Area in China

    Institute of Scientific and Technical Information of China (English)

    LI Xiaolan; ZHANG Hongsheng

    2014-01-01

    In this study, the eff ects of soil moisture on sand saltation and dust emission over the Horqin Sandy Land area are investigated, based on observations of three dust events in 2010. The minimum friction velocity initiating the motion of surface particles, namely, the threshold friction velocity, is estimated to be 0.34, 0.40, and 0.50 m s−1 under the very dry, dry, and wet soil conditions, respectively. In comparison with the observations during the dust events under the very dry and dry soil conditions, the dust emission fl ux during the wet event is smaller, but the saltation activities of sand particles (d≧50 µm) are stronger. The size distributions of airborne dust particles (0.1≦d≦20 µm) show that concentrations of the fi ner dust particles (0.1≦d≦0.3 µm) have a secondary peak under dry soil conditions, while they are absent under wet soil conditions. This suggests that the surface soil particle size distribution can be changed by soil moisture. Under wet soil conditions, the particles appear to have a larger size, and hence more potential saltating particles are available. This explains the occurrence of stronger saltation processes observed under wet soil conditions.

  12. Hazard impact and genetic development of sand dunes west of Samalut, Egypt

    Directory of Open Access Journals (Sweden)

    El Sayed Ahmed El Gammal

    2010-12-01

    These dunes have their source from Oligocene sand and gravel deposits to the north of the study area and from the substratum. While the sands are shiny and more rounded mat grains in the northern part of these dunes due to fluvial processes, the south sands become more markedly “aeolinized” by including less rounded and striated sand grains. They move and increase in size in the down wind direction. The initiation of linear dunes explanted here west of the Nile Valley where the eastern tails of the lee side of the barchan dunes are longer than the western ones and sometimes these tails are connected with each other forming longitudinal sand dunes. These dunes are in mature stage and the southern dune may be in the last modification stage.

  13. Bearings-only target motion analysis based on decreasing dimension by self-adaption aethod to ascertain initial distance%初距自适应估计的降维纯方位目标运动分析

    Institute of Scientific and Technical Information of China (English)

    马鑫; 舒象兰; 孙荣光; 綦敦浩

    2013-01-01

    Bearings-only target motion analysis(BO-TMA) is to estimate the position and velocity of a target from bearing measurements with corrupted noise obtained by an observation platform.Since the problem of the tardy convergence rate and low calculation precision,a least square BTMA model taking the initial distance as the parameter has been formatted and an adaptive method to ascertain initial distance is proposed,this method translates three-dimensional problem into two-dimensional problem and,consequently boosts convergence rate and low calculation precision.Computer simulation results verify the effectiveness of the method.%纯方位目标运动分析(BO-TMA)是一种从探测器所观测到的加噪方位信息和测量载体的机动信息中估算出目标运动要素的方法.针对传统纯方位目标运动分析收敛速度慢,参数估计精度低的问题,本文通过建立以初距为参量的纯方位最小二乘TMA模型,提出一种自适应确定初始距离并求解速度信息的方法,该方法将三维问题转化为二维问题,从而提高收敛速度与估计精度.仿真结果验证了该方法的有效性.

  14. METHOD OF PROCESSING MONAZITE SAND

    Science.gov (United States)

    Welt, M.A.; Smutz, M.

    1958-08-26

    A process is described for recovering thorium, uranium, and rare earth values from monazite sand. The monazite sand is first digested with sulfuric acid and the resulting "monazite sulfate" solution is adjusted to a pH of between 0.4 and 3.0, and oxalate anions are added causing precipitation of the thorium and the rare earths as the oxalates. The oxalate precipitate is separated from the uranium containing supernatant solution, and is dried and calcined to the oxides. The thorium and rare earth oxides are then dissolved in nitric acid and the solution is contacted with tribntyl phosphate whereby an organic extract phase containing the cerium and thorium values is obtained, together with an aqueous raffinate containing the other rare earth values. The organic phase is then separated from the aqueous raffinate and the cerium and thorium are back extracted with an aqueous medium.

  15. Characterization of sand lenses embedded in tills

    DEFF Research Database (Denmark)

    Kessler, Timo Christian; Klint, K.E.S.; Nilsson, B.

    2012-01-01

    of the various types of sand lenses is discussed, primarily in relation to the depositional and glaciotectonic processes they underwent. Detailed characterization of sand lenses facilitates such interpretations. Finally, the observations are linked to a more general overview of the distribution of sand lenses......Tills dominate large parts of the superficial sediments on the Northern hemisphere. These glacial diamictons are extremely heterogeneous and riddled with fractures and lenses of sand or gravel. The frequency and geometry of sand lenses within tills are strongly linked to glaciodynamic processes...... occurring in various glacial environments. This study specifically focuses on the appearance and spatial distribution of sand lenses in tills. It introduces a methodology on how to measure and characterize sand lenses in the field with regard to size, shape and degree of deformation. A set of geometric...

  16. A compact topology for sand automata

    CERN Document Server

    Dennunzio, Alberto; Masson, Benoît

    2008-01-01

    In this paper, we exhibit a strong relation between the sand automata configuration space and the cellular automata configuration space. This relation induces a compact topology for sand automata, and a new context in which sand automata are homeomorphic to cellular automata acting on a specific subshift. We show that the existing topological results for sand automata, including the Hedlund-like representation theorem, still hold. In this context, we give a characterization of the cellular automata which are sand automata, and study some dynamical behaviors such as equicontinuity. Furthermore, we deal with the nilpotency. We show that the classical definition is not meaningful for sand automata. Then, we introduce a suitable new notion of nilpotency for sand automata. Finally, we prove that this simple dynamical behavior is undecidable.

  17. Rheological Characterization of Green Sand Flow

    DEFF Research Database (Denmark)

    Jabbaribehnam, Mirmasoud; Spangenberg, Jon; Hovad, Emil

    2016-01-01

    The main aim of this paper is to characterize experimentally the flow behaviour of the green sand that is used for casting of sand moulds. After the sand casting process is performed, the sand moulds are used for metal castings. The rheological properties of the green sand is important to quantify...... module for characterizing granular materials. The new module enables viscosity measurements of the green sand as function of the shear rate at different flow rates, i.e. 0, 2, 4, 6, 8, 10, 12 and 15 L/min. The results show generally that the viscosity decreases with both the shear- and flow rate....... In addition, the measurements show that the green sand flow follows a shear-thinning behaviour even after the full fluidization point....

  18. Silo model tests with sand

    DEFF Research Database (Denmark)

    Munch-Andersen, Jørgen

    Tests have been carried out in a large silo model with Leighton Buzzard Sand. Normal pressures and shear stresses have been measured during tests carried out with inlet and outlet geometry. The filling method is a very important parameter for the strength of the mass and thereby the pressures...... as well as the flow pattern during discharge of the silo. During discharge a mixed flow pattern has been identified...

  19. Formation of Craters in Sand

    Directory of Open Access Journals (Sweden)

    Vanissra Boonyaleepun

    2007-06-01

    Full Text Available The diameter of craters formed by spheres of varying mass dropped into sand at low speed was studied. The relationship between the diameter of the crater formed and the kinetic energy of the projectile at impact was found to be of the same general form as that for planetary meteor craters. The relationship is shown to be a power law with exponent 0.17.

  20. Formation of Craters in Sand

    Directory of Open Access Journals (Sweden)

    Vanissra Boonyaleepun

    2007-06-01

    Full Text Available The diameter of craters formed by spheres of varying mass dropped into sand at low speed was studied. The relationship between the diameter of the crater formed and the kinetic energy of the projectile at impact was found to be of the same general form as that for planetary meteor craters. The relationship is shown to be a power law with exponent 0.17

  1. Thermal Properties of oil sand

    Science.gov (United States)

    LEE, Y.; Lee, H.; Kwon, Y.; Kim, J.

    2013-12-01

    Thermal recovery methods such as Cyclic Steam Injection or Steam Assisted Gravity Drainage (SAGD) are the effective methods for producing heavy oil or bitumen. In any thermal recovery methods, thermal properties (e.g., thermal conductivity, thermal diffusivity, and volumetric heat capacity) are closely related to the formation and expansion of steam chamber within a reservoir, which is key factors to control efficiency of thermal recovery. However, thermal properties of heavy oil or bitumen have not been well-studied despite their importance in thermal recovery methods. We measured thermal conductivity, thermal diffusivity, and volumetric heat capacity of 43 oil sand samples from Athabasca, Canada, using a transient thermal property measurement instrument. Thermal conductivity of 43 oil sand samples varies from 0.74 W/mK to 1.57 W/mK with the mean thermal conductivity of 1.09 W/mK. The mean thermal diffusivity is 5.7×10-7 m2/s with the minimum value of 4.2×10-7 m2/s and the maximum value of 8.0×10-7 m2/s. Volumetric heat capacity varies from 1.5×106 J/m3K to 2.11×106 J/m3K with the mean volumetric heat capacity of 1.91×106 J/m3K. In addition, physical and chemical properties (e.g., bitumen content, electric resistivity, porosity, gamma ray and so on) of oil sand samples have been measured by geophysical logging and in the laboratory. We are now proceeding to investigate the relationship between thermal properties and physical/chemical properties of oil sand.

  2. Sand-Mud Sediment Transport induced by tidal currents and wind waves in shallow microtidal basins

    Science.gov (United States)

    Carniello, L.; Defina, A.; D'Alpaos, L.

    2011-12-01

    Field data and mathematical modeling have demonstrated that the morphological evolution of shallow tidal basins is the result of the combined effect of tidal currents and wind waves. Tidal currents, in particular, drive the morphological evolution of shallow tidal systems in proximity of the inlets and within the channel network, whereas in shallow areas tidal current mainly acts enhancing the bottom shear stress due to wind waves and redistributing sediments within the basin. In this study we present a mathematical model for sediment entrainment, transport and deposition due to the combined effect of tidal currents and wind waves. The model is coupled with a hydrodynamic module based on the shallow water equations and with a module for the generation and propagation of wind waves. The sediment transport model describes the sediments by the way of a bi-granular mixtures composed by both cohesive and non-cohesive sediments thus considering the contemporary presence of clay, silt and sand which usually characterizes estuaries and tidal basins. Moreover, the model describes the bed evolution and evaluates the variation of bed sediment composition considering also the transition between cohesive and non-cohesive behavior. Attention is focused on some issues concerning the definition of a reliable initial bed composition and the incipient sediment motion which is treated following a stochastic approach for the bottom shear stress and for the critical shear stress distribution. The model is applied to the Lagoon of Venice (Italy) and the results of different simulations are compared, with good agreement, to a series of turbidity measurements collected inside the lagoon. The application of the model to the present bathymetry of the Venice lagoon allows for a first estimation of the actual net amount of sand and mud flowing through the three inlets and also gives some information on bottom evolution in terms of elevation and composition.

  3. Computer Modeling of Sand Transport on Mars Using a Compart-Mentalized Fluids Algorithm (CFA)

    Science.gov (United States)

    Marshall, J.; Stratton, D.

    1999-01-01

    It has been postulated that aeolian transport on Mars may be significantly different from that on Earth. From laboratory experiments simulating martian grain transport [2], it has been observed that (saltating) grains striking the bed can cause hundreds of secondary reptation trajectories when impact occurs at speeds postulated for Mars. Some of the ballistically induced trajectories "die ouf' and effectively join the ranks on the creep population that is merely nudged along by impact. Many of the induced reptation trajectories, however, are sufficiently high for the grains to become part of the saltation load (it is irrelevant to the boundary layer how a grain attained its initial lift force). When these grains, in turn, strike the surface, they too are capable of inducing more reptating grains. This cascading effect has been discussed in connection with terrestrial aeolian transport in an attempt to dispel the notion that sand motion is divisible only into creep and saltation loads. On Earth, only a few grains are splashed by impact. On Mars, it may be hundreds. We developed a computer model to address this phenomenon because there are some important ramifications: First, this ratio may mean that martian aeolian transport is dominated by reptation flux rather than saltation. On Earth, the flux would be a roughly balanced mixture between reptation/creep and saltation. On Venus, there would be no transport other than by saltation. In other words, an understanding of planetary aeolian processes may not be necessarily understood by extrapolating from the "Earth case", with only gravity and atmospheric density/viscosity being considered as variables. Second, the reptation flux on Mars may be self sustaining, so that little input is required by the wind once transport has been initiated. The number of grains saturating the boundary layer near the bed may mean that average grain speed on Mars might conceivably be less than that on Earth. This would say much for models

  4. Evaluation of Durability Parameters of Concrete with Manufacture Sand and River Sand

    Science.gov (United States)

    Sangoju, Bhaskar; Ramesh, G.; Bharatkumar, B. H.; Ramanjaneyulu, K.

    2017-06-01

    Most of the states in our country have banned sand quarrying from the river beds, causing a scarcity of natural river sand for the construction sector. Manufacture sand (M-sand) is one of the alternate solutions to replace the river sand (R-sand) in concrete. The main aim of the present study is to evaluate the durability parameters of concrete with M-sand when compared to that of concrete with R-sand. Corrosion of reinforcement is one of the main deteriorating mechanisms of reinforced concrete due to the ingress of chloride ions or carbon-di-oxide. For comparative evaluation of durability parameters, accelerated tests such as Rapid Chloride Permeability Test, Rapid Chloride Migration Test and accelerated carbonation test were carried out on specimens of R-sand and M-sand. All tests were carried out after 90 days of casting. Test results reveal that the durability parameters of the concrete with M-sand in chloride induced environment is relatively better than that of concrete with R-sand and hence is recommended to use M-sand as a replacement to R-sand.

  5. Sand deposit-detecting method and its application in model test of sand flow

    Institute of Scientific and Technical Information of China (English)

    黎伟; 房营光; 莫海鸿; 谷任国; 陈俊生

    2013-01-01

    Against the background of the sand-flow foundation treatment engineering of Guangzhou Zhoutouzui variable cross-section immersed tunnel, a kind of sand deposit-detecting method was devised on the basis of full-scale model test of sand-flow method. The real-time data of sand-deposit height and radius were obtained by the self-developed sand-deposit detectors. The test results show that the detecting method is simple and has high precision. In the use of sand-flow method, the sand-carrying capability of fluid is limited, and sand particles are all transported to the sand-deposit periphery through crater, gap and chutes after the sand deposit formed. The diffusion range of the particles outside the sand-deposit does not exceed 2.0 m. Severe sorting of sand particles is not observed because of the unique oblique-layered depositing process. The temporal and spatial distributions of gap and chutes directly affect the sand-deposit expansion, and the expansion trend of the average sand-deposit radius accords with quadratic time-history curve.

  6. Characterization of Time-Dependent Contact Angles for Oleic Acid Mixed Sands with Different Particle Size Fractions

    DEFF Research Database (Denmark)

    Wijewardana, Y. N. S.; Kawamoto, Ken; Komatsu, Toshiko

    2014-01-01

    ) mixed sands representing four different particle size fractions ranging from 0.105 to 0.84 mm. Initial soil-water contact angle (αi), and the time dependence of contact angle were measured by the sessile drop method. Results showed that the αi value for fine and middle sand fractions increased rapidly...

  7. Analysis of the forces acting on the saltating particles in the coupled wind-sand-electricity fields

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Based on the theoretical model describing the saltation of sand particles in the coupled wind-sand- electricity fields, the numerical simulations of the forces acting on saltating particles, such as the aerodynamic drag force, Magnus effect, Saffman force and electrostatic force, are analyzed in com- parison to the gravity force of the particles in the steady windblown sand movement. Furthermore, the laws of the above forces vary with the friction velocity, the diameter of the sand particle, the initial an- gular velocity and the lift-off velocity are discussed.

  8. Analysis of the forces acting on the saltating particles in the coupled wind-sand-electricity fields

    Institute of Scientific and Technical Information of China (English)

    WU JianJun; YAN GuangHu

    2009-01-01

    Based on the theoretical model describing the saltation of sand particles in the coupled wind-sand-electricity fields, the numerical simulations of the forces acting on saltating particles, such as the aerodynamic drag force, Magnus effect, Saffman force and electrostatic force, are analyzed in com-parison to the gravity force of the particles in the steady windblown sand movement. Furthermore, the laws of the above forces vary with the friction velocity, the diameter of the sand particle, the initial an-gular velocity and the lift-off velocity are discussed.

  9. Objective Motion Cueing Criteria Investigation Based on Three Flight Tasks

    Science.gov (United States)

    Zaal, Petrus M. T.; Schroeder, Jeffery A.; Chung, William W.

    2015-01-01

    This paper intends to help establish fidelity criteria to accompany the simulator motion system diagnostic test specified by the International Civil Aviation Organization. Twelve air- line transport pilots flew three tasks in the NASA Vertical Motion Simulator under four different motion conditions. The experiment used three different hexapod motion configurations, each with a different tradeoff between motion filter gain and break frequency, and one large motion configuration that utilized as much of the simulator's motion space as possible. The motion condition significantly affected: 1) pilot motion fidelity ratings, and sink rate and lateral deviation at touchdown for the approach and landing task, 2) pilot motion fidelity ratings, roll deviations, maximum pitch rate, and number of stick shaker activations in the stall task, and 3) heading deviation after an engine failure in the takeoff task. Significant differences in pilot-vehicle performance were used to define initial objective motion cueing criteria boundaries. These initial fidelity boundaries show promise but need refinement.

  10. SAND

    DEFF Research Database (Denmark)

    Thorsen, Grete

    Der er udført et konsolideringsforsøg med bakkesand fra Lunds grusgrav, Lund no. O. forsøget er udført i samme konsolideringsapparat, som er anvendt til måling af deformationsegenskaberne af mange forskellige danske jordarter. Forsøgsresultaterne er søgt tolket som ved forsøg med andre jordarter....

  11. Seismic behavior of tire waste-sand mixtures for transportation infrastructure in cold regions

    Institute of Scientific and Technical Information of China (English)

    Aye Edinliler; Ozgur Yildiz

    2015-01-01

    Tire wastes have many properties that are valuable from a geotechnical engineering perspective, such as low density, high strength, thermal insulation, energy absorption capacity, permeability, durability, compressibility, resilience, and high frictional strength. Thus, tire wastes offer good thermal characteristics in resisting frost penetration and have good drainage characteristics, being as permeable as coarse granular soil for fill materials. The many advantages of tire wastes make the material suitable for transportation infrastructure construction in cold regions. Also, tire wastes with high damping prop-erty make them a preferable admixture with sand for transportation infrastructures in seismic regions. This study aimed to determine the seismic performance of certain tire waste-sand mixtures in cold regions. A 70% sand-30% tire crumb mixture by weight (TC30) with a very high damping property was selected for analysis as an engineering material for transportation infrastructure. Small-scale shake-table tests were conducted on this material as well as on a sand-only sample under two different temperatures, 0 °C and 20 °C, to simulate cold-region and moderate-temperature performance, respectively. The 1999İzmit Earthquake Excitation (EW) (Mw=7.4) was taken as the input motion. Test results showed that the tire waste-sand mixture at 0 °C showed better seismic performance than that at room temperature, suggesting that a tire waste-sand mixture in cold regions may reduce seismic hazards to infrastructure.

  12. Liquefaction of Sand under Low Confining Pressure

    Institute of Scientific and Technical Information of China (English)

    YANG Shaoli; Rolf Sandven; Lars Grande

    2003-01-01

    Undrained behaviour of sand under low cell pressure was studied in static and cyclic triaxial tests. It was found that very loose sand liquefies under static loading with the relative density being a key parameter for the undrained behaviour of sand. In cyclic triaxial tests, pore water pressures built up during the cyclic loading and exceeded the confining cell pressure. This process was accompanied by a large sudden increase in axial deformation. The necessary number of cycles to obtain liquefaction was related to the confining cell pressure, the amplitude of cyclic loading and the relative density of sand.In addition, the patterns of pore water pressure response are different from those of sand samples with different relative densities. The test results are very useful for expounding scour mechanism around coastal structures since they relate to the low stress behaviour of the sand.

  13. Creep Behavior of Frozen Sand.

    Science.gov (United States)

    1981-06-01

    temperature and stress range. There was a 2strong stress dependance to S (r =0.95) for saturated Manchester Fine Sand which does not agree with RPT. The...Curves at High Stress 161 Ratio D/Du = 0.505 for Frozen HF’S at w=10% IV-20 Minimum Strain Rate Dependance on Stress 162 Ratio for Frozen MFS IV-21 Minimum...Strain Rate Dependance on Relative 163 Density for Frozen MFS IV-22 Temperature Stage Test on Frozen Saturated 164 MFS under a Load of D=9.24MPa Fig

  14. Motion Simulator

    Science.gov (United States)

    1993-01-01

    MOOG, Inc. supplies hydraulic actuators for the Space Shuttle. When MOOG learned NASA was interested in electric actuators for possible future use, the company designed them with assistance from Marshall Space Flight Center. They also decided to pursue the system's commercial potential. This led to partnership with InterActive Simulation, Inc. for production of cabin flight simulators for museums, expositions, etc. The resulting products, the Magic Motion Simulator 30 Series, are the first electric powered simulators. Movements are computer-guided, including free fall to heighten the sense of moving through space. A projection system provides visual effects, and the 11 speakers of a digital laser based sound system add to the realism. The electric actuators are easier to install, have lower operating costs, noise, heat and staff requirements. The U.S. Space & Rocket Center and several other organizations have purchased the simulators.

  15. Recent advances in waterglass sand technologies

    Institute of Scientific and Technical Information of China (English)

    ZHU Chun-xi

    2007-01-01

    This paper reports some new understandings and advances in waterglass sand technologies. The multiple chemical modification process can increase the binding strength of the waterglass sand by up to 50%-70%.Therefore, the additions of the modified waterglass can be decreased to 3.0%-4.0% for CO2 process and to 2.0%-2.5% for organic ester hardening process, and greatly improve the collapsibility and reclaimability of the sand. Based on the new understandings and experimental results reported in this paper, several original ideas, such as nano modification, have been proposed to promote advances of waterglass sand technologies,

  16. PROSPECTS FIXATION DRIFT SANDS PHYSICOCHEMICAL METHOD

    Directory of Open Access Journals (Sweden)

    Maujuda MUZAFFAROVA

    2016-09-01

    Full Text Available This article is based on the theoretical foundations of secure mobile sand being considered for reducing the negative impact of one of the manifestations of exogenous plains on such an important natural-technical system as a railroad. It suggests practical measures to build a system of design protection against sand drifts. The article also suggests ways to conserve resources and rational use of machinery and performers as well as the consolidation of mobile sand wet with water soluble waste of local production of waste dextrin. Consolidation is exposed on dry and wet sand.

  17. Innovative developments in sand reclamation technologies

    Directory of Open Access Journals (Sweden)

    R. Dañko

    2011-04-01

    Full Text Available Proper sand management and efficient sand reclamation system are two main factors influencing economical and ecological side of modern foundry plant. It is well known fact that the production of 1 metric ton of casting from ferrous alloys generates circa 1 metric ton of waste [1], which due to containing certain amounts of harmful and dangerous compounds should undergo a reclamation – at least of the main component, which means a silica sand grains. The paper present problems of scientific and development research concerning the innovative reclamation technologies of used foundry sands such as: mechanical-cryogenic reclamation and innovative thermal reclamation.

  18. Motion Model Employment using interacting Motion Model Algorithm

    DEFF Research Database (Denmark)

    Hussain, Dil Muhammad Akbar

    2006-01-01

    The paper presents a simulation study to track a maneuvering target using a selective approach in choosing Interacting Multiple Models (IMM) algorithm to provide a wider coverage to track such targets.  Initially, there are two motion models in the system to track a target.  Probability of each...... model being correct is computed through a likelihood function for each model.  The study presented a simple technique to introduce additional models into the system using deterministic acceleration which basically defines the dynamics of the system.  Therefore, based on this value more motion models can...... be employed to increase the coverage.  Finally, the combined estimate is obtained using posteriori probabilities from different filter models.   The implemented approach provides an adaptive scheme for selecting various number of motion models.  Motion model description is important as it defines the kind...

  19. Production from multiple zones of a tar sands formation

    Energy Technology Data Exchange (ETDEWEB)

    Karanikas, John Michael; Vinegar, Harold J

    2013-02-26

    A method for treating a tar sands formation includes providing heat to at least part of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat is allowed to transfer from the heaters to at least a portion of the formation. Fluids are produced from the formation through at least one production well that is located in at least two zones in the formation. The first zone has an initial permeability of at least 1 darcy. The second zone has an initial of at most 0.1 darcy. The two zones are separated by a substantially impermeable barrier.

  20. Sand Failure Mechanism and Sanding Parameters in Niger Delta Oil Reservoirs

    OpenAIRE

    Sunday Isehunwa,; Andrew Farotade

    2010-01-01

    Sand production is a major issue during oil and gas production from unconsolidated reservoirs. In predicting the onset of sand production, it is important to accurately determine the failure mechanism and the contributing parameters. The aim of this study was to determine sand failure mechanism in the Niger-Delta, identify themajor contributing parameters and evaluate their effects on sanding.Completion and production data from 78 strings completed on 22 reservoirs in a Niger Delta oil Field ...

  1. Robust global motion estimation

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A global motion estimation method based on robust statistics is presented in this paper. By using tracked feature points instead of whole image pixels to estimate parameters the process speeds up. To further speed up the process and avoid numerical instability, an alterative description of the problem is given, and three types of solution to the problem are compared. By using a two step process, the robustness of the estimator is also improved. Automatic initial value selection is an advantage of this method. The proposed approach is illustrated by a set of examples, which shows good results with high speed.

  2. Auditory Motion Elicits a Visual Motion Aftereffect

    Directory of Open Access Journals (Sweden)

    Christopher C. Berger

    2016-12-01

    Full Text Available The visual motion aftereffect is a visual illusion in which exposure to continuous motion in one direction leads to a subsequent illusion of visual motion in the opposite direction. Previous findings have been mixed with regard to whether this visual illusion can be induced cross-modally by auditory stimuli. Based on research on multisensory perception demonstrating the profound influence auditory perception can have on the interpretation and perceived motion of visual stimuli, we hypothesized that exposure to auditory stimuli with strong directional motion cues should induce a visual motion aftereffect. Here, we demonstrate that horizontally moving auditory stimuli induced a significant visual motion aftereffect—an effect that was driven primarily by a change in visual motion perception following exposure to leftward moving auditory stimuli. This finding is consistent with the notion that visual and auditory motion perception rely on at least partially overlapping neural substrates.

  3. Collective motion

    Science.gov (United States)

    Vicsek, Tamás; Zafeiris, Anna

    2012-08-01

    We review the observations and the basic laws describing the essential aspects of collective motion - being one of the most common and spectacular manifestation of coordinated behavior. Our aim is to provide a balanced discussion of the various facets of this highly multidisciplinary field, including experiments, mathematical methods and models for simulations, so that readers with a variety of background could get both the basics and a broader, more detailed picture of the field. The observations we report on include systems consisting of units ranging from macromolecules through metallic rods and robots to groups of animals and people. Some emphasis is put on models that are simple and realistic enough to reproduce the numerous related observations and are useful for developing concepts for a better understanding of the complexity of systems consisting of many simultaneously moving entities. As such, these models allow the establishing of a few fundamental principles of flocking. In particular, it is demonstrated, that in spite of considerable differences, a number of deep analogies exist between equilibrium statistical physics systems and those made of self-propelled (in most cases living) units. In both cases only a few well defined macroscopic/collective states occur and the transitions between these states follow a similar scenario, involving discontinuity and algebraic divergences.

  4. Study of Black Sand Particles from Sand Dunes in Badr, Saudi Arabia Using Electron Microscopy

    Directory of Open Access Journals (Sweden)

    Haider Abbas Khwaja

    2015-08-01

    Full Text Available Particulate air pollution is a health concern. This study determines the microscopic make-up of different varieties of sand particles collected at a sand dune site in Badr, Saudi Arabia in 2012. Three categories of sand were studied: black sand, white sand, and volcanic sand. The study used multiple high resolution electron microscopies to study the morphologies, emission source types, size, and elemental composition of the particles, and to evaluate the presence of surface “coatings or contaminants” deposited or transported by the black sand particles. White sand was comprised of natural coarse particles linked to wind-blown releases from crustal surfaces, weathering of igneous/metamorphic rock sources, and volcanic activities. Black sand particles exhibited different morphologies and microstructures (surface roughness compared with the white sand and volcanic sand. Morphological Scanning Electron Microscopy (SEM and Laser Scanning Microscopy (LSM analyses revealed that the black sand contained fine and ultrafine particles (50 to 500 nm ranges and was strongly magnetic, indicating the mineral magnetite or elemental iron. Aqueous extracts of black sands were acidic (pH = 5.0. Fe, C, O, Ti, Si, V, and S dominated the composition of black sand. Results suggest that carbon and other contaminant fine particles were produced by fossil-fuel combustion and industrial emissions in heavily industrialized areas of Haifa and Yanbu, and transported as cloud condensation nuclei to Douf Mountain. The suite of techniques used in this study has yielded an in-depth characterization of sand particles. Such information will be needed in future environmental, toxicological, epidemiological, and source apportionment studies.

  5. Amplitude equation for under water sand-ripples in one dimension

    DEFF Research Database (Denmark)

    Sand-ripples under oscillatory water flow form periodic patterns with wave lengths primarily controlled by the amplitude d of the water motion. We present an amplitude equation for sand-ripples in one spatial dimension which captures the formation of the ripples as well as secondary bifurcations...... observed when the amplitude $d$ is suddenly varied. The equation has the form h_t=- ε(h-mean(h))+((h_x)^2-1)h_(xx)- h_(xxxx)+ δ((h_x)^2)_(xx) which, due to the first term, is neither completely local (it has long-range coupling through the average height mean(h)) nor has local sand conservation. We argue...

  6. Sand Waves in Environmental Flows: Insights gained by LES

    Science.gov (United States)

    Sotiropoulos, Fotis

    2014-11-01

    In fluvial and coastal environments, sediment transport processes induced by near-bed coherent structures in the turbulent boundary layer developing over a mobile sediment bed result in the formation of dynamically rich sand waves, or bed forms, which grow and migrate continuously. Bed form migration alters streambed roughness and provides the primary mechanism for transporting large amounts of sediment through riverine systems impacting the morphology, streambank stability, and ecology of waterways. I will present recent computational advances, which have enabled coupled, hydro-morphodynamic large-eddy simulation (LES) of turbulent flow in mobile-bed open channels. Numerical simulations: 1) elucidate the role of near-bed sweeps in the turbulent boundary layer as the mechanism for initiating the instability of the initially flat sand bed; 2) show how near-bed processes give rise to aperiodic eruptions of suspended sediment at the free surface; and 3) clarify the mechanism via which sand waves migrate. Furthermore, in agreement with recent experimental observations, the computed spectra of the resolved velocity fluctuations above the bed exhibit a distinct spectral gap whose width increases with distance from the bed. The spectral gap delineates the spectrum of turbulence from that of slowly evolving coherent structures associated with sand wave migration. The talk will also present computational results demonstrating the feasibility of carrying out coupled, hydro-morphodynamic LES of large dunes migrating in meandering streams and rivers with embedded hydraulic structures and discuss future challenges and opportunities. This work was supported by NSF Grants EAR-0120914 and EAR-0738726, and National Cooperative Highway Research Program Grant NCHRP-HR 24-33.

  7. Controlling the motion of multiple objects on a Chladni plate

    OpenAIRE

    2016-01-01

    The origin of the idea of moving objects by acoustic vibration can be traced back to 1787, when Ernst Chladni reported the first detailed studies on the aggregation of sand onto nodal lines of a vibrating plate. Since then and to this date, the prevailing view has been that the particle motion out of nodal lines is random, implying uncontrollability. But how random really is the out-of-nodal-lines motion on a Chladni plate? Here we show that the motion is sufficiently regular to be statistica...

  8. Pattern formation - Instabilities in sand ripples

    DEFF Research Database (Denmark)

    Hansen, J. L.; v. Hecke, M.; Haaning, A.

    2001-01-01

    Sand ripples are seen below shallow wavy water and are formed whenever water oscillates over a bed of sand. Here we analyse the instabilities that can upset this perfect patterning when the ripples are subjected to large changes in driving amplitude or frequency, causing them to deform both...

  9. Pilot Project Sand Groynes Delfland Coast

    NARCIS (Netherlands)

    Hoekstra, R.; Walstra, D.J.R.; Swinkels, C.S.

    2012-01-01

    In October and November 2009 a pilot project has been executed at the Delfland Coast in the Netherlands, constructing three small sandy headlands called Sand Groynes. Sand Groynes are nourished from the shore in seaward direction and anticipated to redistribute in the alongshore due to the impact of

  10. Silica sand resources in the Netherlands

    NARCIS (Netherlands)

    Meulen, M.J. van der; Westerhoff, W.E.; Menkovic, A.; Gruijters, S.H.L.L.; Dubelaar, C.W.; Maljers, D.

    2009-01-01

    Silica sand, (almost) pure quartz sand, is a valuable and scarce mineral resource within the shallow Dutch subsurface. High-grade deposits are exploited in the southeastemmost part of the country, as raw material for the glass, ceramic, chemical and other process industries. Dutch land-use policy re

  11. Pilot Project Sand Groynes Delfland Coast

    NARCIS (Netherlands)

    Hoekstra, R.; Walstra, D.J.R.; Swinkels, C.S.

    2012-01-01

    In October and November 2009 a pilot project has been executed at the Delfland Coast in the Netherlands, constructing three small sandy headlands called Sand Groynes. Sand Groynes are nourished from the shore in seaward direction and anticipated to redistribute in the alongshore due to the impact of

  12. Understanding Colombian Amazonian white sand forests

    NARCIS (Netherlands)

    Peñuela-Mora, M.C.

    2014-01-01

    Although progress has been made in studies on white sand forests in the Amazon, there is still a considerable gap in our knowledge of the unique species composition of white sand forests and their structure and dynamics, especially in Western Amazon. This thesis aims to fill this gap by addressing t

  13. Motion control report

    CERN Document Server

    2013-01-01

    Please note this is a short discount publication. In today's manufacturing environment, Motion Control plays a major role in virtually every project.The Motion Control Report provides a comprehensive overview of the technology of Motion Control:* Design Considerations* Technologies* Methods to Control Motion* Examples of Motion Control in Systems* A Detailed Vendors List

  14. Continuous adsorption of Pb(II) and methylene blue by engineered graphite oxide coated sand in fixed-bed column

    Energy Technology Data Exchange (ETDEWEB)

    Gong, Ji-Lai, E-mail: jilaigong@gmail.com [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Zhang, Yong-Liang; Jiang, Yan [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Zeng, Guang-Ming, E-mail: zgming@hnu.edu.cn [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Cui, Zhi-Hui; Liu, Ke; Deng, Can-Hui; Niu, Qiu-Ya; Deng, Jiu-Hua [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Huan, Shuang-Yan [State Key Laboratory for Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China)

    2015-03-01

    Highlights: • GO-sand was prepared by coating GO on the surface of sand. • Pb(II) and MB were efficiently removed by GO-sand filter in column. • The removal of MB was enhanced with the presence of Pb(II). • GO-sand is low-cost and convenient for its application as packed bed filter. - Abstract: The mixture of several effluents, caused by the improper handling and management of effluents, generated multi-component wastewater containing both metals and dyes, leading to the complicated treatment process. In this study, a continuous adsorption of Pb(II) and methylene blue (MB) has been studied in single and binary solutions by using graphite oxide coated sand (GO-sand) as an adsorbent in a fixed-bed column. GO-sand was analyzed by X-ray photoelectron spectroscopy before and after analyte adsorption. Compared with sand filter, adsorption quantity and capacity for Pb(II) and MB by GO-sand filter were greatly increased. In Pb(II) and MB single solutions, the experimental parameters were investigated in detail including initial concentration, flow rate, bed depth and pH. Exhaustion time decreased with increasing initial concentration and flow rate, and increased with increasing bed depth and pH. In the Pb(II)-MB binary solution, exhaustion time significantly decreased for Pb(II) adsorption, but increased for MB adsorption. The reason was explained that the more favorable adsorption for MB onto the surface of GO-sand than that for Pb(II), which was derived from π–π interaction between MB and GO on sand surface in packed filter. The Yoon–Nelson model was applied at different concentration of Pb(II) and MB to predict the breakthrough curves. The experimental data were well fit with the model indicating that it was suitable for this column design.

  15. Natural and human controls of the Holocene evolution of the beach, aeolian sand and dunes of Caesarea (Israel)

    Science.gov (United States)

    Roskin, J.; Sivan, D.; Shtienberg, G.; Roskin, E.; Porat, N.; Bookman, R.

    2015-12-01

    The study focuses on the Holocene appearance, chronology and drivers of beach sand deposition and inland aeolian sand transport around the Roman-Byzantine ruins of Caesarea, Israel. Beach sand, sand sheets, nebkha, linear and transverse dunes as well as parabolic and transverse interdunes along two transects were sampled in the current study down to their substrate. Sixteen new optically stimulated luminescence ages cluster at ∼5.9-3.3 ka, ∼1.2-1.1 ka (800-900 AD) and ∼190-120 years ago (1825-1895 AD) indicating times of middle and late Holocene sand sheet depositions and historical dune stabilization. The first age cluster indicates that beach sand accumulated when rates of global sea level rise declined around 6-5 ka. Until ∼4 ka sand sheets encroached up to 2.5 km inland. Historical and archaeological evidence points to sand mobilization since the first century AD. Sand sheets dating to 1.2-1.1 ka, coevally found throughout the dunefield represent sand stabilization due to vegetation reestablishment attributed to gradual and fluctuating decline in human activity from the middle Early Islamic period until the 10th century. Historical and chronological evidence of the existence of transverse and coppice dunes from the 19th century suggest that dunes only formed in the last few centuries. The study illustrates the initial role of natural processes, in this case decline in global sea level rise and the primary and later role of fluctuating human activity upon coastal sand mobility. The study distinguishes between sand sheets and dunes and portrays them as sensors of environmental changes.

  16. Infrasonic induced ground motions

    Science.gov (United States)

    Lin, Ting-Li

    On January 28, 2004, the CERI seismic network recorded seismic signals generated by an unknown source. Our conclusion is that the acoustic waves were initiated by an explosive source near the ground surface. The meteorological temperature and effective sound speed profiles suggested existence of an efficient near-surface waveguide that allowed the acoustic disturbance to propagate to large distances. An explosion occurring in an area of forest and farms would have limited the number of eyewitnesses. Resolution of the source might be possible by experiment or by detailed analysis of the ground motion data. A seismo-acoustic array was built to investigate thunder-induced ground motions. Two thunder events with similar N-wave waveforms but different horizontal slownesses are chosen to evaluate the credibility of using thunder as a seismic source. These impulsive acoustic waves excited P and S reverberations in the near surface that depend on both the incident wave horizontal slowness and the velocity structure in the upper 30 meters. Nineteen thunder events were chosen to further investigate the seismo-acoustic coupling. The consistent incident slowness differences between acoustic pressure and ground motions suggest that ground reverberations were first initiated somewhat away from the array. Acoustic and seismic signals were used to generate the time-domain transfer function through the deconvolution technique. Possible non-linear interaction for acoustic propagation into the soil at the surface was observed. The reverse radial initial motions suggest a low Poisson's ratio for the near-surface layer. The acoustic-to-seismic transfer functions show a consistent reverberation series of the Rayleigh wave type, which has a systematic dispersion relation to incident slownesses inferred from the seismic ground velocity. Air-coupled Rayleigh wave dispersion was used to quantitatively constrain the near-surface site structure with constraints afforded by near-surface body

  17. Mecoprop (MCPP) removal in full-scale rapid sand filters at a groundwater-based waterworks

    Energy Technology Data Exchange (ETDEWEB)

    Hedegaard, Mathilde J., E-mail: mjhe@env.dtu.dk; Arvin, Erik; Corfitzen, Charlotte B.; Albrechtsen, Hans-Jørgen

    2014-11-15

    Contamination by the herbicide mecoprop (MCPP) was detected in groundwater abstraction wells at Kerteminde Waterworks in concentrations up to 0.08 μg/L. MCPP was removed to below detection limit in a simple treatment line where anaerobic groundwater was aerated and subsequently filtered by primary and secondary rapid sand filters. Water quality parameters were measured throughout the waterworks, and they behaved as designed for. MCPP was removed in secondary rapid sand filters — removal was the greatest in the sand filters in the filter line with the highest contact time (63 min). In these secondary sand filters, MCPP concentration decreased from 0.037 μg/L to below the detection limit of 0.01 μg/L. MCPP was removed continuously at different filter depths (0.80 m). Additionally, biodegradation, mineralisation and adsorption were investigated in the laboratory in order to elucidate removal mechanisms in the full-scale system. Therefore, microcosms were set up with filter sand, water and {sup 14}C-labelled MCPP at an initial concentration of 0.2 μg/L. After 24 h, 79–86% of the initial concentration of MCPP was removed. Sorption removed 11–15%, while the remaining part was removed by microbial processes, leading to a complete mineralisation of 13–18%. Microbial removal in the filter sand was similar at different depths of the rapid sand filter, while the amount of MCPP which adsorbed to the filter sand after 48 h decreased with depth from 21% of the initial MCPP in the top layer to 7% in the bottom layer. It was concluded that MCPP was removed in secondary rapid sand filters at Kerteminde Waterworks, to which both adsorption and microbial degradation contributed. - Highlights: • A full-scale groundwater based waterworks was able to remove MCPP. • In the secondary rapid sand filters, MCPP decreased from 0.037 μg/L to < 0.010 μg/L. • The filter sand removed MCPP both by sorption and by microbial degradation. • Microbial removal was unchanged while

  18. Choosing an optimum sand control method

    Directory of Open Access Journals (Sweden)

    Ehsan Khamehchi

    2015-06-01

    Full Text Available Formation sand control is always one of the main concerns of production engineers. There are some different methods to prevent sand production. Choosing a method for preventing formation sand production depends on different reservoir parameters and politic and economic conditions. Sometimes, economic and politic conditions are more effective to choose an optimum than reservoir parameters. Often, simultaneous investigation of politic and economic conditions with reservoir parameters has different results with what is expected. So, choosing the best sand control method is the result of thorough study. Global oil price, duration of sand control project and costs of necessary equipment for each method as economic and politic conditions and well productivity index as reservoir parameter are the main parameters studied in this paper.

  19. Caenorhabditis elegans SAND-1 is essential for RAB-7 function in endosomal traffic.

    Science.gov (United States)

    Poteryaev, Dmitry; Fares, Hanna; Bowerman, Bruce; Spang, Anne

    2007-01-24

    The small rab-GTPase RAB-7 acts in endosome and endosome to lysosome traffic. We identified SAND-1 as a protein required for RAB-7 function based on similarities between SAND-1 and RAB-7 RNAi phenotypes. Although the initial uptake of yolk protein in oocytes, or of soluble secreted (ss) GFP in coelomocytes, appeared normal, further transport along the endocytic traffic route was delayed in the absence of SAND-1 function, and yolk proteins failed to reach yolk granules efficiently. Moreover, in coelomocytes, ssGFP and BSA-Texas-Red were endocytosed but not transported to lysosomes. We show that SAND-1 is essential for RAB-7 function at the transition from early to late endosomes, but not for RAB-7 function at lysosomes.

  20. Altitude of the top of the Sparta Sand and Memphis Sand in three areas of Arkansas

    Science.gov (United States)

    Pugh, Aaron L.; Westerfield, Paul W.; Gonthier, Gerard; Poynter, David T.

    1998-01-01

    The Sparta Sand and Memphis Sand form the second most productive aquifer in Arkansas. The Sparta Sand and Memphis Sand range in thick- ness from 0 to 900 feet, consisting of fine- to medium-grained sands interbedded with layers of silt, clay, shale, and minor amounts of lignite. Within the three areas of interest, the top surface of the Sparta Sand and Memphis Sand dips regionally east and southeast towards the axis of the Mississippi Embayment syncline and Desha Basin. Local variations in the top surface may be attributed to a combination of continued development of structural features, differential compaction, localized faulting, and erosion of the surface prior to subsequent inundation and deposition of younger sediments.

  1. Sand Failure Mechanism and Sanding Parameters in Niger Delta Oil Reservoirs

    Directory of Open Access Journals (Sweden)

    Sunday Isehunwa,

    2010-05-01

    Full Text Available Sand production is a major issue during oil and gas production from unconsolidated reservoirs. In predicting the onset of sand production, it is important to accurately determine the failure mechanism and the contributing parameters. The aim of this study was to determine sand failure mechanism in the Niger-Delta, identify themajor contributing parameters and evaluate their effects on sanding.Completion and production data from 78 strings completed on 22 reservoirs in a Niger Delta oil Field were evaluated. Sand failure mechanisms and contributing parameters were identified and compared with published profiles. The results showed that cohesive stress is the predominant sand failure mechanism. Water cut, bean size and gas oil ratio (GOR impact sand production in the Niger Delta.

  2. Routine screening of harmful microorganisms in beach sands: implications to public health

    Science.gov (United States)

    Sabino, Raquel; Rodrigues, R.; Costa, I.; Carneiro, Carlos; Cunha, M.; Duarte, A.; Faria, N.; Ferriera, F.C.; Gargate, M.J.; Julio, C.; Martins, M.L.; Nevers, Meredith; Oleastro, M.; Solo-Gabriele, H.; Verissimo, C.; Viegas, C.; Whitman, Richard L.; Brandao, J.

    2014-01-01

    Beaches worldwide provide recreational opportunities to hundreds of millions of people and serve as important components of coastal economies. Beach water is often monitored for microbiological quality to detect the presence of indicators of human sewage contamination so as to prevent public health outbreaks associated with water contact. However, growing evidence suggests that beach sand can harbor microbes harmful to human health, often in concentrations greater than the beach water. Currently, there are no standards for monitoring, sampling, analyzing, or managing beach sand quality. In addition to indicator microbes, growing evidence has identified pathogenic bacteria, viruses, and fungi in a variety of beach sands worldwide. The public health threat associated with these populations through direct and indirect contact is unknown because so little research has been conducted relating to health outcomes associated with sand quality. In this manuscript, we present the consensus findings of a workshop of experts convened in Lisbon, Portugal to discuss the current state of knowledge on beach sand microbiological quality and to develop suggestions for standardizing the evaluation of sand at coastal beaches. The expert group at the “Microareias 2012” workshop recommends that 1) beach sand should be screened for a variety of pathogens harmful to human health, and sand monitoring should then be initiated alongside regular water monitoring; 2) sampling and analysis protocols should be standardized to allow proper comparisons among beach locations; and 3) further studies are needed to estimate human health risk with exposure to contaminated beach sand. Much of the manuscript is focused on research specific to Portugal, but similar results have been found elsewhere, and the findings have worldwide implications.

  3. Global sand trade is paving the way for a tragedy of the sand commons

    Science.gov (United States)

    Torres, A.; Brandt, J.; Lear, K.; Liu, J.

    2016-12-01

    In the first 40 years of the 21st century, planet Earth is highly likely to experience more urban land expansion than in all of history, an increase in transportation infrastructure by more than a third, and a great variety of land reclamation projects. While scientists are beginning to quantify the deep imprint of human infrastructure on biodiversity at large scales, its off-site impacts and linkages to sand mining and trade have been largely ignored. Sand is the most widely used building material in the world. With an ever-increasing demand for this resource, sand is being extracted at rates that far exceed its replenishment, and is becoming increasingly scarce. This has already led to conflicts around the world and will likely lead to a "tragedy of the sand commons" if sustainable sand mining and trade cannot be achieved. We investigate the environmental and socioeconomic interactions over large distances (telecouplings) of infrastructure development and sand mining and trade across diverse systems through transdisciplinary research and the recently proposed telecoupling framework. Our research is generating a thorough understanding of the telecouplings driven by an increasing demand for sand. In particular, we address three main research questions: 1) Where are the conflicts related to sand mining occurring?; 2) What are the major "sending" and "receiving" systems of sand?; and 3) What are the main components (e.g. causes, effects, agents, etc.) of telecoupled systems involving sand mining and trade? Our results highlight the role of global sand trade as a driver of environmental degradation that threatens the integrity of natural systems and their capacity to deliver key ecosystem services. In addition, infrastructure development and sand mining and trade have important implications for other sustainability challenges such as over-fishing and global warming. This knowledge will help to identify opportunities and tools to better promote a more sustainable use

  4. WIND TUNNEL EXPERIMENT OF SAND VELOCITY IN NATURE AEOLIAN SAND TRANSPORT USING PARTICLE IMAGE VELOCIMETRY%天然混合沙运动速度特征的风洞PIV实验

    Institute of Scientific and Technical Information of China (English)

    佟鼎; 黄宁

    2011-01-01

    Sand velocity in aeolian sand transport is measured using the PIV system(Particle Imaging Velocimetry) in a wind tunnel.The velocity probability distribution of ascending and descending particles,as well the influences of sand ripple on the sand particle motion are analyzed.The results show that velocity distributions of take-off particles and particles during sand movement accord with logarithm normal distribution.The mean incident velocity of sand particles is 1.005-1.4 times higher than take-off ones with different wind speed.It is found that sand ripples play an important role on the sand particles motion,which is a key factor that can not be neglected.%采用PIV(Particle Image Velocimetry)系统测量了天然混合沙风沙两相流中沙粒的速度分布特征,得到了沙粒入射以及起跳的速度分布情况,并且分析了沙波纹对风沙运动的影响。结果表明:沙粒运动过程中的速度分布与沙粒起跳速度的分布可以应用对数正态分布来表明;当有沙波纹存在时,沙粒总体速度分布与平坦沙床面差别很大,是不可忽略的重要因素;平坦沙床面沙粒平均入射速度是起跳平均速度的1.005倍~1.4倍,具体关系可以应用线性函数来拟合。

  5. Mulitple Origins of Sand Dune-Topography Interactions on Titan

    Science.gov (United States)

    Goggin, H.; Ewing, R. C.; Hayes, A.; Cisneros, J.; Epps, J. C.

    2015-12-01

    The interaction between sand dune patterns and topographic obstacles is a primary signal of sand transport direction in the equatorial region of Saturn's moon, Titan. The streamlined, tear drop appearance of the sand-dune patterns as they wrap around obstacles and a dune-free zone on the east side of many obstacles gives the impression that sand transport is from the west to east at equatorial latitudes. However, the physical mechanism behind the dune-obstacle interaction is not well explained, leaving a gap in our understanding of the equatorial sand transport and implied wind directions and magnitudes on Titan. In order to better understand this interaction and evaluate wind and sand transport direction, we use morphometric analysis of optical images on Earth and Cassini SAR images on Titan combined with analog wind tunnel experiments to study dune-topography interactions. Image analysis is performed in a GIS environment to map spatial variations in dune crestline orientations proximal to obstacles. We also use digital elevation models to and analyze the three-dimensional geometry - height, length, width and slope of the dune-topography relationships on Earth. Preliminary results show that dune patterns are deflected similarly around positive, neutral, or negative topography, where positive topography is greater than the surrounding dune height, neutral topography is at dune height and negative topography is lower than dune heights. In the latter case these are typically intra-dune field playas. The obstacle height, width, slope and wind variability appear to play a primary role in determining if a lee-dune, rather than a dune-free lee-zone, develops. In many cases a dune-free playa with evaporite and mud desiccation polygons forms lee-ward of the obstacle. To support and elaborate on the mapping and spatial characterization of dune-topography interactions, a series of experiments using a wind tunnel were conducted. Wind tunnel experiments examine the formation

  6. Critical state of sand matrix soils.

    Science.gov (United States)

    Marto, Aminaton; Tan, Choy Soon; Makhtar, Ahmad Mahir; Kung Leong, Tiong

    2014-01-01

    The Critical State Soil Mechanic (CSSM) is a globally recognised framework while the critical states for sand and clay are both well established. Nevertheless, the development of the critical state of sand matrix soils is lacking. This paper discusses the development of critical state lines and corresponding critical state parameters for the investigated material, sand matrix soils using sand-kaolin mixtures. The output of this paper can be used as an interpretation framework for the research on liquefaction susceptibility of sand matrix soils in the future. The strain controlled triaxial test apparatus was used to provide the monotonic loading onto the reconstituted soil specimens. All tested soils were subjected to isotropic consolidation and sheared under undrained condition until critical state was ascertain. Based on the results of 32 test specimens, the critical state lines for eight different sand matrix soils were developed together with the corresponding values of critical state parameters, M, λ, and Γ. The range of the value of M, λ, and Γ is 0.803-0.998, 0.144-0.248, and 1.727-2.279, respectively. These values are comparable to the critical state parameters of river sand and kaolin clay. However, the relationship between fines percentages and these critical state parameters is too scattered to be correlated.

  7. Sand Flies and Their Control Methods.

    Science.gov (United States)

    Çetin, Hüseyin; Özbel, Yusuf

    2017-06-01

    The main aim of managing arthropod vectors that carry the disease agents is interrupting the infection cycle. Therefore, the management of the disease implies that all precautions related to all elements (i.e., human, arthropod vector, and reservoir) in the infection cycle need to be taken. There are important points that need to be considered while dealing with sand flies (Diptera: Psychodidae: Phlebotominae), which in many regions worldwide, particularly in tropical and subtropical areas, are vectors of diseases such as leishmaniasis and sand fly fever and are the arthropods of the infection cycle. Because the larval control of the sand flies is very difficult and almost impossible, the management is mainly conducted for the adults. The most effective strategy for reducing both sand fly fever and leishmaniasis is managing sand flies, particularly in areas where humans are located. In this review, the morphology, biology, and taxonomy of sand flies; the integrated fighting and management methods such as insecticide-impregnated bed nets and use of curtains, zooprophylaxis, indoor and outdoor residual applications, larvicides, repellents, and insecticide-impregnated dog collars; and data regarding many issues such as insecticide resistance in sand flies have been emphasized on in the review.

  8. Critical State of Sand Matrix Soils

    Directory of Open Access Journals (Sweden)

    Aminaton Marto

    2014-01-01

    Full Text Available The Critical State Soil Mechanic (CSSM is a globally recognised framework while the critical states for sand and clay are both well established. Nevertheless, the development of the critical state of sand matrix soils is lacking. This paper discusses the development of critical state lines and corresponding critical state parameters for the investigated material, sand matrix soils using sand-kaolin mixtures. The output of this paper can be used as an interpretation framework for the research on liquefaction susceptibility of sand matrix soils in the future. The strain controlled triaxial test apparatus was used to provide the monotonic loading onto the reconstituted soil specimens. All tested soils were subjected to isotropic consolidation and sheared under undrained condition until critical state was ascertain. Based on the results of 32 test specimens, the critical state lines for eight different sand matrix soils were developed together with the corresponding values of critical state parameters, M, λ, and Γ. The range of the value of M, λ, and Γ is 0.803–0.998, 0.144–0.248, and 1.727–2.279, respectively. These values are comparable to the critical state parameters of river sand and kaolin clay. However, the relationship between fines percentages and these critical state parameters is too scattered to be correlated.

  9. Invasive plants on disturbed Korean sand dunes

    Science.gov (United States)

    Kim, Kee Dae

    2005-01-01

    The sand dunes in coastal regions of South Korea are important ecosystems because of their small size, the rare species found in this habitat, and the beautiful landscapes they create. This study investigated the current vegetative status of sand dunes on three representative coasts of the Korean peninsula, and on the coasts of Cheju Island, and assessed the conditions caused by invasive plants. The relationships between the degree of invasion and 14 environmental variables were studied. Plots of sand dunes along line transects perpendicular to the coastal lines were established to estimate vegetative species coverage. TWINSPAN (Two-Way Indicator Species Analysis), CCA (Canonical Correspondence Analysis), and DCCA (Detrended Canonical Correspondence Analysis) were performed to classify communities on sand dunes and assess species composition variation. Carex kobomugi, Elymus mollis, and Vitex rotundifolia were found to be the dominant species plotted on the east, the west, and the peripheral coasts of Cheju Island, respectively. Vegetation on the south coast was totally extinct. The 19 communities, including representative C. kobomugi, C. kobomugi- Ixeris repens, C. kobomugi- Oenothera biennis, E. mollis, Lolium multiflorum- Calystegia soldanella, and V. rotundifolia- C. kobomugi, were all classified according to TWINSPAN. Oenothera biennis and L. multiflorum were exotics observed within these native communities. CCA showed that invasive native and exotic species distribution was segregated significantly, according to disturbance level, exotic species number, gravel, sand and silt contents, as well as vegetation size. It further revealed that human disturbance can strongly favor the settlement of invasive and exotic species. Restoration options to reduce exotic plants in the South Korean sand dune areas were found to be the introduction of native plant species from one sand dune into other sand dune areas, prohibition of building and the introduction of exotic

  10. Lund Sand No 0:part 2

    OpenAIRE

    Ibsen, Lars Bo; Jakobsen, Finn Rosendal

    1996-01-01

    During the last 15 years the Geotechnical Engineering Group (GEG) at Aalborg University has performed triaxial tests with a sand called Lund No 0. Lund No 0 is a graded sand from a gravel pit near Horsens in Denmark. For the classification of the sand the following tests have been performed: Sieve test, Grain density, ds, Maximum, emax, and minimum, emin, void ratio. The strength parameters of Lund No 0 are detennined by some drained and undrained triaxial tests in the Danish Triaxial Cell. T...

  11. Lund Sand No 0:part 1

    OpenAIRE

    Ibsen, Lars Bo; Jakobsen, Finn Rosendal

    1996-01-01

    During the last 15 years the Geotechnical Engineering Group (GEG) at Aalborg University has performed triaxial tests with a sand called Lund No 0. Lund No 0 is a graded sand from a gravel pit near Horsens in Denmark. For the classification of the sand the following tests have been performed: Sieve test, Grain density, ds, Maximum, emax, and minimum, emin, void ratio. The strength parameters of Lund No 0 are detennined by some drained and undrained triaxial tests in the Danish Triaxial Cell. T...

  12. Biodegradable materials as foundry moulding sands binders

    Directory of Open Access Journals (Sweden)

    K. Major - Gabryś

    2015-07-01

    Full Text Available The aim of this article is to show the possibility of using biodegradable materials as part of the composition of foundry moulding and core sand binders. Research shows that moulding sands with biodegradable materials selected as binders are not only less toxic but are also better suited to mechanical reclamation than moulding sands with phenol-furfuryl resin. The use of biodegradable materials as additives to typical synthetic resins can result in their decreased toxicity and improved ability to reclamation as well as in accelerated biodegradation of binding material leftovers of mechanical reclamation.

  13. Neutron Star Motion in the Disk Galaxy

    Institute of Scientific and Technical Information of China (English)

    WEI Ying-Chun; A.Taani; PAN Yuan-Yue; WANG Jing; CAI Yan; LIU Gao-Chao; LUO A-Li; ZHANG Hong-Bo; ZHAO Yong-Heng

    2010-01-01

    @@ The neutron star motions are based on the undisturbed finitely thick galactic disk gravitational potential model.Two initial conditions,I.e.the locations and velocities,are considered.The Monte Carlo method is employed to separate rich diversities of the orbits of neutron stars into several sorts.The Poincaré section has the potential to play an important role in the diagnosis of the neutron star motion.It has been observed that the increasing ratio of the motion range vertical to the galactic plane to that parallel to the galactic plane results in the irregularity of neutron star motion.

  14. Watching Faults Grow in Sand

    Science.gov (United States)

    Cooke, M. L.

    2015-12-01

    Accretionary sandbox experiments provide a rich environment for investigating the processes of fault development. These experiments engage students because 1) they enable direct observation of fault growth, which is impossible in the crust (type 1 physical model), 2) they are not only representational but can also be manipulated (type 2 physical model), 3) they can be used to test hypotheses (type 3 physical model) and 4) they resemble experiments performed by structural geology researchers around the world. The structural geology courses at UMass Amherst utilize a series of accretionary sandboxes experiments where students first watch a video of an experiment and then perform a group experiment. The experiments motivate discussions of what conditions they would change and what outcomes they would expect from these changes; hypothesis development. These discussions inevitably lead to calculations of the scaling relationships between model and crustal fault growth and provide insight into the crustal processes represented within the dry sand. Sketching of the experiments has been shown to be a very effective assessment method as the students reveal which features they are analyzing. Another approach used at UMass is to set up a forensic experiment. The experiment is set up with spatially varying basal friction before the meeting and students must figure out what the basal conditions are through the experiment. This experiment leads to discussions of equilibrium and force balance within the accretionary wedge. Displacement fields can be captured throughout the experiment using inexpensive digital image correlation techniques to foster quantitative analysis of the experiments.

  15. Effect of Chromite-Silica Sands Characteristics on Performance of Ladle Filler Sands for Continuous Casting

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Free opening rate is mainly determined by the performance of the ladle filler sand. High free opening rates of ladles are required in steel making to improve steel quality. Chromite ladle filler sands are one of the most widely used ladle filler sand. Several operative variables and materials characteristics affect the performance of the sands. Three sets of chromite ladle filler sands were selected and researches were focused on the sintering hehaviour and per- formance of the sands under operative conditions. The effect of particle size distribution on sintering, microstruc- ture, flowability, and permeability were presented. In all cases, the particle size varies from 0.1 to 1.5 mm corre- sponding to free flowing powders. One of the samples has higher permeability factor in comparison with others due to low particle size distribution. The other sample presents very good free opening due to its very good flowability and permeability factor.

  16. Motion in radiotherapy

    DEFF Research Database (Denmark)

    Korreman, Stine Sofia

    2012-01-01

    This review considers the management of motion in photon radiation therapy. An overview is given of magnitudes and variability of motion of various structures and organs, and how the motion affects images by producing artifacts and blurring. Imaging of motion is described, including 4DCT and 4DPET...

  17. Analysis of effectiveness of used sands reclamation treatment – in various technological devices

    Directory of Open Access Journals (Sweden)

    R. Dańko

    2009-10-01

    Full Text Available The analysis of effectiveness of spent sands reclamation treatment performed in technological devices of various intensity of dry reclamation – during which used binding material is being removed from grain surfaces – is presented in the paper. Variety of reclamation influences was considered via the realization of the so called elementary operations such as: rubbing, grinding and crushing [1-5], which are realised mainly in dry mechanical reclamation devices but also appear in other technological devices for sand preparation.The model rotor reclaimer and two types of mixers used for preparing initial foundry sands with resin U 404 and hardener 100 T3 of the Hüttenes-Albertus Company were applied for tests.The theoretical model for assessing the effectiveness of reclamation treatment developed by the author [3, 4], was experimentally verified [5, 7], with the application of standard testing procedures. The model can be considered a new tool enabling the selection of optimal reclamation times for the given used sand at the assumed intensity of silica sand matrix recovery. Sand mixture of a proper composition fulfilled needed technological properties after total hardening was used as charge material in experiments. The reclamation treatment consisted of mechanical and mechanical-cryogenic reclamation performed within a wide range of times and conditions influencing the treatment intensity.

  18. Source, route and effect of Asian sand dust on environment and the oceans

    Institute of Scientific and Technical Information of China (English)

    Kai Zhang; Fahe Chai; Renjian Zhang; Zhigang Xue

    2010-01-01

    We summarize in this overview achievements in current research frontiers in Asian sand dust with emphasis on the method for sand dust research,the sources of sand dust aerosols,emission of sand dust,mechanism of sand dust weather,chemical transformation during transport,and influences on climatic environment and oceans.Our main results show that most of Asian sand dust comes from Mongolia,the Gobi Desert,arid and semiarid desert areas in northwest China,which is divided into initial sources and enhanced sources.Half of the global production of dust originates from Asian dust source regions.Asian dust weather is so immense that it can cover a 5-7-day journey from the sources to the Korean Peninsula,Japan Islands,and the Pacific Ocean to even impact North America.Asian dust weather plays an active role in the biogeochemical cycles of trace elements in the mid-latitude Northern Hemisphere.

  19. Experimental investigation on ballistic stability of high-speed projectile in sand

    Science.gov (United States)

    Zhang, Wei; Huang, Xianglin; Qi, Yafei; Li, Dacheng; Tao, Jialiang; Huang, Wei

    2017-01-01

    The investigation on ballistic stability of high-speed projectile in granular materials is important to study the EPW (earth-penetrating weapon). Laboratory-scaled sand entry experiments for the trajectory in the sand have been performed at a range of velocities from 30 m/s to 150 m/s. In addition, pressure sensor was embedded in the sand to record the sand stress which reflects the penetration performance of projectile during the impact. The slender projectiles were designed into flat nose shape with three kinds of L/D (length-diameter ratio) to make comparisons on the trajectory when those projectiles were launched at normal and oblique impact angles (0˜25deg) along a view window. A high-speed camera beside window was employed to capture the entire process of projectiles' penetration. Basing on the comparison of different tests, theoretical analysis is carried out on the relationship between ballistic stability and associated conditions. By utilizing DIC technique, the vector field of sand velocity was acquired, and the spreading direction of the impacting energy was observed. It can be concluded that the sand stress is the function of penetrating velocity, L/D and the shot angle. It increases with the growing of penetrating velocity and L/D, decreases with the shot angle. To a certain extent, the biggest initial velocity leads to the highest stress.

  20. Sand Lake WMD vegetation mapping project update

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Final report on the vegetation mapping project at Sand Lake Wetland Management District. This project is being completed by the use of SPRING software and ground...

  1. Bioaugmentation of flow-through sand filters

    DEFF Research Database (Denmark)

    Samuelsen, Elin Djurhuus

    Global applications of pesticides in agricultural production have led to the detection of trace amounts of pesticides in groundwater resources in levels exceeding the EU threshold limit for drinking water of 0.1 µg L-1. Pesticide-polluted groundwater may be remediated by inoculating waterworks sand...... for degradation performances in flow-through sand columns, with the aim of identifying a suitable inoculant strain for future environmental applications. Another aim was to identify a suitable genetic marker to monitor phenoxy acid degradation in strain Sphingobium sp. PM2. We were not able to link motility...... and biofilm formation to the strains´ ability to adhere to sand. Nevertheless, a correlation was found between cell surface hydrophobicity and adhesion and overall degradation performances in flow-through sand columns. We identified S phingobium sp. PM2 as a promising inoculant strain, displaying efficient...

  2. Petrophysical Analysis of Oil Sand in Athabasca

    Science.gov (United States)

    cheong, S.; Lee, H.

    2013-12-01

    Oil sands are the major unconventional energy sources which have great reserves in Alberta, Canada. Recovery techniques such as CSS (Cyclic Steam Stimulation) and SAGD (Steam Assisted Gravity Drainage) enabled to develop deeper bitumen about several hundred meter depth. Before applying CSS and SAGD, reservoir heterogeneity of mud barriers or shale breccias should be clarified to establish injection and production wells successfully. We conducted the integrated petro-physical analysis for oil sands deposits in Athabasca by correlating well logs with seismic data. From 33 well logs and 3D seismic, we have made P-wave impedance by recursive inversion. Target formations of our analysis were the top of Wabiskaw member. Using inverted impedance and multi-attributes, porosity volume was derived at a target depth. Porosity of time slice 375 ms ranged 20 ~ 40 % stretching porous sand body from NE to SW direction. Characteristics of porosity distribution may be useful to design optimum oil sands recovery in Athabasca.

  3. Carbon cycle: New pathways in the sand

    Science.gov (United States)

    Rao, Alexandra

    2017-01-01

    Organic carbon decomposition in anoxic marine sediments was thought to be dominated by bacteria, but experimental data and microbial culture studies now show that microalgae buried in coastal sands may also play an important role in carbon turnover.

  4. CRADE OF SAND AND DUST STORM WEATHER

    Institute of Scientific and Technical Information of China (English)

    Niu Ruoyun; Tian Cuiying; Bi Baogui; Yang Keming; Wang Youheng; Tuo Ya; Ding Haifang; Zhang Tairen

    2011-01-01

    Background Sand and dust storm,as one of the main disastrous weathers that affect northern China,not only affect the people health and normal life,but cause the short-term climatic changes due to the direct and indirect radiation of the earth-atmosphere system through the dust floating in the sky.The sand end dust weather and its potential harm on the national economy,ecological environment,social activities and other aspects have aroused worldwide concern.

  5. Laboratory evaluation of selected tar sand asphalts

    Energy Technology Data Exchange (ETDEWEB)

    Button, J.W.; Epps, J.A.; Gallaway, B.M.

    1980-12-01

    Three tar sand asphalts of similar grades prepared from one syncrude by three different refining methods were characterized by tests commonly used to specify paving asphalts together with certain special tests. Asphalt-aggregate mixtures were prepared using these asphalts and tested in the laboratory to determine strength stiffness stability, tensile properties, temperature effects and water susceptibility. Comparison of the tar sand asphalt properties to conventional petroleum asphalt properties reveal no striking differences.

  6. Response to Oil Sands Products Assessment

    Science.gov (United States)

    2015-09-01

    Tailings ponds are an operating facility common to all types of surface mining. For oil sands, tailings consisting of water , sand, clay, and residual ...oil, are pumped to these basins—or ponds— where settling occurs and water is recycled for reuse in the process. When the ponds are no longer required...of crude oil transported by tank vessel in Washington waters . In a 2013 Bloomburg Business news article , Dan Murtaugh states, “The dock probably

  7. Treating tar sands formations with dolomite

    Energy Technology Data Exchange (ETDEWEB)

    Vinegar, Harold J.; Karanikas, John Michael

    2010-06-08

    Methods for treating a tar sands formation are described herein. The tar sands formation may include dolomite and hydrocarbons. Methods may include providing heat at less than the decomposition temperature of dolomite from one or more heaters to at least a portion of the formation. At least some of the hydrocarbon fluids are mobilized in the formation. At least some of the hydrocarbon fluids may be produced from the formation.

  8. Review of four major environmental effects monitoring programs in the oil sands region

    Energy Technology Data Exchange (ETDEWEB)

    Lott, E.O.; Jones, R.K. [EO Consulting, BC (Canada)

    2010-10-15

    The lack of knowledge on current environmental effects monitoring programs for the mineable oil sands region generates a low public confidence in environment health monitoring and reporting programs for the oil sands operations. In 2010, the Oil Sands Research and Information Network (OSRIN) supervised a study reviewing the major environmental effects monitoring programs that are underway in the Regional Municipality of Wood Buffalo. Four main environmental effects monitoring and reporting organizations existing in the oil sands area were engaged to describe their programs through this study: Alberta Biodiversity Monitoring Institute (ABMI), Cumulative Environmental Management Association (CEMA), Regional Aquatic Monitoring Program (RAMP), Wood Buffalo Environmental Association (WBEA). These different organizations have specific roles in providing information, data and understanding of ecosystem effects. A one page visual summary of environmental effects monitoring in the oil sands area resulted from the information received from these organizations and detailed fact sheets were presented for each one of the programs. The report of this study also presents seven other environmental monitoring initiatives or organizations such as Alberta Environment and Environment Canada environmental effects monitoring program. The main observation that emerged from the review was the lack of detailed understanding shown by the stakeholders regarding the monitoring activities performed in the oil sands area. There is a lack of communication of the different programs that are conducted in the region. The study also pointed out that no efforts were put in cross-linking the various programs to be assured that every concerns related to environmental effects associated with oil sands operations were addressed. A better understanding of environmental effects and an improvement in public confidence in the data and its interpretation would probably be observed with the establishment of a

  9. Application of microwave energy for curing of molding sands containing oil binders

    Directory of Open Access Journals (Sweden)

    M. Stachowicz

    2008-07-01

    Full Text Available This works presents the results of studies concerning possibility of application of microwave heating in the curing process of molding sands containing oil binders. Molding sands prepared with three kinds of binders, that is oils C, DL and Retanol, have been subject to experiments. The sands have been dried with two methods: in a microwave chamber of 750W power and, for comparison, with classical method at the temperature of 200°C for 120 minutes. Tensile and bending strength of the samples have been determined after cooling down. It has been found that microwave drying in the low-power device used for experiments is effective only in case of molding sand prepared with addition of DL binder. The temperature of heated, even up to 32 minutes in a microwave chamber, blocks prepared from the remaining two masses, was insufficient to initiate binding process. The undertaken attempts of binder modification and introduction of additives intensifying microwave heating process allowed for achievement of satisfactory results. It has been found that power of the heating device is the main factor determining efficiency of microwave curing of molding sands containing oil binders. An additional experiment has been conducted on a laboratory workstation allowing for microwave heating of small mass samples with a high output power of magnetron concentrated in a small substrate volume. It has been observed that microwave drying process of molding sands was of dynamic character over a short period of time, not exceeding 120 seconds, thus assuring efficient curing of the sands containing the used oil binders. Therefore, application of devices of properly high microwave output power allows for efficient drying of oil molding sands, while simultaneously assuring the possibility to reduce time and energy consumption necessary for production of foundry cores of proper functional characteristics.

  10. Pragmatics of reclaimed sand quality assessment recovered nowadays from various used sand systems

    Directory of Open Access Journals (Sweden)

    J. Dańko

    2010-04-01

    Full Text Available The assessment of the reclamation degree of used sands is not a simple, clearly defined issue. The great variety of technologies ofmoulding and core sands, based on the organic and inorganic binders does not allow the use of a single, universal index assessing thedegree of reclamation. The article presents the problems of research relating to selection of proper criteria for assessing the degree ofreclamation process of used moulding and core sands deriving from different technologies. The most often applied in practice types ofused sands and the most adequate in practice methods of assessing the degrees of their reclamation were characterized.

  11. Sand Dune Encroachment and Desertification Processes of the Rigboland Sand Sea, Central Iran.

    Science.gov (United States)

    Ahmady-Birgani, Hesam; McQueen, Kenneth G; Moeinaddini, Mazaher; Naseri, Hamidreza

    2017-05-08

    Early studies on sand dune movement and desertification in Iran have not always been convincingly demonstrated because of problems with the field-based measurements. In some areas where various land uses have been engulfed by aeolian sand dunes, desertification is clear, but in other less settled areas, it may not be so obvious. The objective of this study is to demonstrate encroachments of the Rigboland sand sea, central Iran, in its different directions and variable magnitude rates. Determining the rate and direction of the sand sea movements is critical for specifying which lands should be prioritized and quickly protected. The study has trialed a change detection technique which uses a Cross-Tabulation module to compare two available LandsatTM images over the Rigboland sand sea. This indicates that within a ten-year span (from 1988 to 1998) more than 200 ha/yr were added to the Rigboland sand sea, from the alluvial fan landforms in the eastern upstream, outer margins of the Rigboland sand sea. Coupled with GIS techniques, this type of analysis of the remote sensing (RS) images provides an effective tool for the monitoring and prognostication of sand dune movement and sand sea change.

  12. Recent Sand Avalanching on Rabe Crater Dunes

    Science.gov (United States)

    2000-01-01

    Dark streaks on the steep, down-wind slopes of sand dunes in Rabe Crater are seen at several locations in this Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image. These streaks indicate relatively recent (i.e., in the past few years or less) movement of sand down these slopes.Sand dunes move forward by the combined action of wind that drives sand up the shallow slope on the windward side of the dune (in this case, the slopes that face toward the lower right) and the avalanching of this sand down the steeper, lee-side slope. The steep slope is also known as the slip face. The dark streaks indicated by arrows are evidence for sand avalanches that occurred within a few months or years of the time when the picture was taken in March 1999. Other streaks which are seen criss-crossing the dunes may be the result of passing dust devils. This image is illuminated from the upper left and located in Rabe Crater of the Hellespontus-Noachis region near 44.2oS, 325.6oW.

  13. Predicting the occurrence of sand banks in the North Sea

    NARCIS (Netherlands)

    Veen, van der Henriët H.; Hulscher, Suzanne J.M.H.

    2009-01-01

    Sand banks have a wavelength between 1 and 10 km, and they are up to several tens of meters high. Also, sand banks may have an impact on large-scale human activities that take place in the North Sea like sand mining, shipping, offshore wind farms, etc. Therefore, it is important to know where sand b

  14. Development of the Gran Desierto sand sea, northwestern Mexico

    Science.gov (United States)

    Blount, Grady; Lancaster, Nicholas

    1990-08-01

    Three major eolian sand populations can be recognized in the Gran Desierto sand sea of northwestern Mexico by using spectral data from the Landsat thematic mapper in conjunction with textural and mineralogical studies of surface sands. Each sand population has distinct textural, mineralogic, and spectral properties that can be related to sand-dune morphology and position with reference to source areas and transport paths of the sands. The oldest eolian sediment in the sand sea was derived from the early to middle Pleistocene Colorado River that flowed through the area of the western Gran Desierto. Subsequent inputs of eolian sands came from the area of the present Colorado River valley and the coast south of the sand sea. The spatial and temporal pattern of eolian deposition in the region has been controlled by Quaternary tectonic and climatic changes, resulting in the episodic input and deposition of sand.

  15. Effects of advanced oxidation on green sand properties via iron casting into green sand molds.

    Science.gov (United States)

    Wang, Yujue; Cannon, Fred S; Voigt, Robert C; Komarneni, Sridhar; Furness, J C

    2006-05-01

    The effects of advanced oxidation (AO) processing on the properties of green sand were studied via pouring cast iron into green sand molds. Upon cooling, the green sand molds were autopsied at various distances from the metal-sand interface. Autopsy green sand samples collected from a mold that incorporated AO water were characterized and compared to controlled samples collected from a similar autopsied mold made with conventional tap water (TAP). It was found that the AO processing removed a coating of coal pyrolysis products from the clay surface that typically accumulated on the clay surface. As a result, the AO-conditioned green sand retained 10-15% more active clay as measured bythe standard ultrasonic methylene blue titration than did the TAP-conditioned green sand. The AO processing also nearly doubled the generation of activated carbon from the normalized amount of coal composition of the green sand during the casting process. The AO-enhanced activated carbon generation and the AO-incurred clay surface cleaning provided the AO-conditioned green sand with higher normalized pore volume, and thus higher normalized m-xylene adsorption capacity, i.e., relative to before-metal-pouring conditions. Furthermore, mathematical analysis indicated that the AO-conditioned green sand better retained its important properties after pouring than did the TAP-conditioned green sand. Effectively, this meant after metal pouring, the AO-conditioned sample offered about the same net properties as the TAP-conditioned sample, even though the AO-conditioned sample contained less clay and coal before metal pouring. These results conformed to the full-scale foundry empirical finding that when AO is used, foundries need less makeup clay and coal addition through each casting cycle, and they release less air emissions.

  16. Contribution of laser altimetry images to the geomorphology of the Late Holocene inland drift sands of the European Sand Belt

    NARCIS (Netherlands)

    Jungerius, P.D.; Riksen, M.J.P.M.

    2010-01-01

    The paper explores the possibilities of applying the analysis of laser altimetry images to Dutch drift sands. All along the European Sand Belt, which stretches from Great Britain to the Ural Mountains, Late Glacial cover sands, river dunes and other ice-age deposits were reactivated as drift sand du

  17. Contribution of laser altimetry images to the geomorphology of the Late Holocene inland drift sands of the European Sand Belt

    NARCIS (Netherlands)

    Jungerius, P.D.; Riksen, M.J.P.M.

    2010-01-01

    The paper explores the possibilities of applying the analysis of laser altimetry images to Dutch drift sands. All along the European Sand Belt, which stretches from Great Britain to the Ural Mountains, Late Glacial cover sands, river dunes and other ice–age deposits were reactivated as drift sand du

  18. Contribution of laser altimetry images to the geomorphology of the Late Holocene inland drift sands of the European Sand Belt

    NARCIS (Netherlands)

    Jungerius, P.D.; Riksen, M.J.P.M.

    2010-01-01

    The paper explores the possibilities of applying the analysis of laser altimetry images to Dutch drift sands. All along the European Sand Belt, which stretches from Great Britain to the Ural Mountains, Late Glacial cover sands, river dunes and other ice–age deposits were reactivated as drift sand

  19. The Karakum and Kyzylkum sand seas dynamics; mapping and palaeoclimatic interpretations

    Science.gov (United States)

    Maman, Shimrit; Blumberg, Dan G.; Tsoar, Haim; Porat, Naomi

    2015-04-01

    Sand seas are large basins in deserts that are mantled by wind-swept sand and that exhibit varying degrees of vegetation cover. Wilson (1973) was the first to globally map and classify sand seas. Beyond Wilson's maps, however, little research has been published regarding the Karakum and Kyzylkum sand seas of Central Asia. Wilson's maps delineate active ergs from inactive ergs based solely on precipitation. His assumption of annual average rainfall as a factor determining mobility vs. stability of sand seas is too simplistic and does not take into consideration other factors such as biogenic soil crusts and wind power, both of which are known to have major effects on the dynamics of sand dunes. Literature related to mapping and classifying the Central Asian ergs by remote sensing or sand sea classification state (stable/active) is lacking. Moreover, the palaeoclimatic significance of dunes in Central Asia is difficult to assess, as there has been few studies of dune stratigraphy and numerical ages are lacking. Optically stimulated luminescence (OSL) is a firm optical dating method that is used to determine the elapsed time since quartz grains were last exposed to sunlight, thus, their burial. Yet, absolute ages indicating mobilization and stabilization of these sands, are still inadequately known and are here under discussion. The broad concern of this research was to determine the dynamics of the Central Asian sand seas and study the palaeoclimatic changes that brought to their stabilization. As there are no reliable maps or aeolian discussion of these sands, establishment of a digital data base was initially conducted, focusing on identifying and mapping these sand seas. The vast area and inaccessibility make traditional mapping methods virtually impossible. A variety of space-borne imagery both optical and radar, with varying spectral and spatial resolutions was used. These images provided the basis for mapping sand distribution, dune forms, and vegetation cover

  20. Bright sand/dark dust: The identification of active sand surfaces on the Earth and Mars

    Science.gov (United States)

    Blount, H. G., II; Greeley, R.; Christensen, P. R.; Arvidson, R.

    1987-05-01

    Field studies and analysis of LANDSAT Thematic Mapper data in the Gran Desierto, Mexico may shed light on a technique to distinguish active from inactive (relict) sand surfaces. Active sand bodies in the study area are consistently brighter (by an average of 20%) at visual and near infrared wavelengths and darker at thermal infrared wavelengths than compositionally similar inactive sands. The reasons for the albedo difference between active and inactive sands are reviewed and the mixing model of Johnson et al. is examined for tracing the provenance of sands based on albedo and spectral variations. Portions of the wavelengths covered by the Mars Orbiter correspond to the Thematic Mapper data. The identification of active sands on Earth, with a priori knowledge of bulk composition and grain size distribution, may allow the remote mapping of active sand surfaces on Mars. In conjuction with thermal infrared remote sensing for composition, it may also provide a method for the remote determination of grain size distributions within sand/silt mixtures.

  1. Simulating and understanding sand wave variation: A case study of the Golden Gate sand waves

    Science.gov (United States)

    Sterlini, F.; Hulscher, S.J.M.H.; Hanes, D.M.

    2009-01-01

    In this paper we present a detailed comparison between measured features of the Golden Gate sand wave field and the results of a nonlinear sand wave model. Because the Golden Gate sand waves exhibit large variation in their characteristics and in their environmental physics, this area gives us the opportunity to study sand wave variation between locations, within one well-measured, large area. The nonlinear model used in this paper is presently the only tool that provides information on the nonlinear evolution of large-amplitude sand waves. The model is used to increase our understanding of the coupling between the variability in environmental conditions and the sand wave characteristics. Results show that the model is able to describe the variation in the Golden Gate sand waves well when both the local oscillating tidal current and the residual current are taken into account. Current and water depth seem to be the most important factors influencing sand wave characteristics. The simulation results give further confidence in the underlying model hypothesis and assumptions. Copyright 2009 by the American Geophysical Union.

  2. MORPHOMETRIC CHARACTERIZATION OF THE SAND FRACTION IN A SAND GRAIN IMAGE CAPTURE SYSTEM1

    Directory of Open Access Journals (Sweden)

    Lucimar Arruda Viana

    Full Text Available ABSTRACT Morphology studies assume significant importance in analysis of phenomena of granular systems packaging, in particular with a view to the use of the technique of soil stabilization named particle size correction in forest roads. In this context, this study aimed to develop and operationalize a Sand Grain Image Capture System and, hereby, determine the morphological indices of the sand fractions of two sandy soils called João Pinheiro (JP and Cachoeira da Prata (CP. Soil samples, air-dried, were sieved (2.0 mm nominal mesh size for removal of gravels. The materials that passed through the sieve were subjected to dispersion, washing in 0.053 mm nominal mesh size sieve, removal of organic matter and iron oxides to obtain the clean sand fractions. Subsequently, each soil sample was sieved for separation into twelve classes, between the diameters of 0.149 mm and 1.190 mm, using a Rotap shaker. Next, tests were carried out to characterize the morphometric attributes of the twelve classes of sand fractions of the soils studied. For validation of the performance of the Sand Grain Image Capture System, the results were compared to those obtained using a standard procedure for image analysis. The analysis of the results led to the following conclusions: (i the sand fraction of the JP soil presented higher values for the morphometric indices roundness, elongation and compactness compared to sand fraction of the CP soil; and (ii the Sand Grain Image Capture System worked properly, with practicality.

  3. Probability of rebound and eject of sand particles in wind-blown sand movement

    Institute of Scientific and Technical Information of China (English)

    Li Xie; Xiaojing Zheng

    2007-01-01

    When incident particles impact into a sand bed in wind-blown sand movement, rebound of the incident particles and eject of the sand particles by the incident particles affect directly the development of wind sand flux. In order to obtain rebound and eject lift-off probability of the sand particles, we apply the particle-bed stochastic collision model presented in our pervious works to derive analytic solutions of velocities of the incident and impacted particles in the postcollision bed. In order to describe randomness inherent in the real particle-bed collision, we take the incident angle, theimpact position and the direction of resultant action of sand particles in sand bed on the impacted sand particle as random variables, and calculate the rebound and eject velocities,angles and coefficients (ratio of rebound and eject velocity to incident velocity). Numerical results are found in accordance with current experimental results. The rebound and eject lift-off probabilities versus the incident and creeping velocities are predicted.

  4. Pretreatment of turkey fat-containing wastewater in coarse sand and gravel/coarse sand bioreactors.

    Science.gov (United States)

    Gaur, Rashmi Singh; Cai, Ling; Tuovinen, Olli H; Mancl, Karen M

    2010-02-01

    Fat, oil and grease in wastewater can be difficult to treat because of their slow decomposition. Traditional pretreatment facilities to remove fat, oil and grease from wastewater are increasingly costly. The hypothesis in this study was that pretreatment of animal fat-containing wastewater in sand and sand/gravel filters facilitates the conversion of slowly degradable organic matter measured as the difference between chemical oxygen demand (COD) and 5-day biochemical oxygen demand (BOD(5)) for subsequent biological treatment. The pretreatment was evaluated using simulated turkey-processing wastewater and coarse sand and sand/gravel filters at a constant hydraulic loading rate of 132L/m(2)/day. Two types of fixed media reactors were employed: (i) one set with a varying depth of coarse sand, and (ii) the second was similar but with an additional pea gravel cap. The results indicated that the relative removal of COD was slightly improved in the sand bioreactors with a pea gravel cap irrespective of the depth of coarse sand, but partial conversion to BOD(5) was not consistently demonstrated. Pea gravel may act as a sieve to entrap organic matter including fat globules from the wastewater. Multiple dosing at the same daily loading rate slightly improved the treatment efficiency of the sand bioreactors. The ratios of influent-COD/effluent-COD were always greater than 1.0 following a change in the dosing frequency after a rest period, suggesting that organic matter, specifically fat globules in this case, was retained by the column matrix.

  5. On the hindered settling of sand-mud suspensions

    Science.gov (United States)

    Spearman, Jeremy; Manning, Andrew J.

    2017-04-01

    Hindered settling, the process by which the settling of sediment particles becomes impeded due to the proximity of other sediment particles, can be an important process for the coastal modeller, especially in highly muddy environments. It is also a significant process in other disciplines such as chemical engineering, the modelling of debris flow, the study of turbidites, piping of slurries and the understanding of processes occurring within a dredger hopper. This study first examines the hindered settling behaviour of monodisperse suspensions in order to create a framework for polydisperse hindered settling that works for both non-cohesive and cohesive suspensions. The Richardson-Zaki equation is adapted to make it compatible with the changes with viscosity that occur near the point at which suspensions become solid. The modified monodisperse settling equation is then compared to data for hindered settling of cohesive suspensions and shown to be consistent with the transition between hindered settling and the initial permeability phase of consolidation. Based on the monodisperse framework developed initially, this paper proposes a hindered settling model for sand/mud mixtures which is based on a modification of the Masliyah (1979) and Lockett and Bassoon (1979) hindered settling equation. The model is shown to reproduce the hindered settling of a variety of different sediment mixtures whilst reducing the extent of empiricism often associated with the modelling of polydisperse hindered settling of mud/sand mixtures.

  6. Formation of sand ripples under a turbulent liquid flow

    CERN Document Server

    Franklin, Erick de Moraes

    2016-01-01

    Sand ripples are commonly observed in both nature and industry. For example, they are found on riverbeds and in oil pipelines that transport sand. In both natural and industrial cases, ripples increase friction between the bed and fluid and are related to flooding, high pressure drops, and transients. Ripples appear when sediments are entrained as bed load (a mobile granular layer) and are usually considered to be the result of initial bedforms that eventually saturate. Given the small aspect ratio of the initial bedforms, linear analyses can be used to understand the formation of ripples. This paper presents a linear stability analysis of a granular bed under a turbulent flow of a liquid. This analysis takes into consideration all the main mechanisms and parameters involved in the turbulent liquid case, including some important parameters that have not yet been considered together such as the bed compactness and the bed-load threshold shear stress. The results of this analysis are compared with published exp...

  7. K West Basin Sand Filter Backwash Sample Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Fiskum, Sandra K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Smoot, Margaret R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Coffey, Deborah S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pool, Karl N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-03-01

    A sand filter is used to help maintain water clarity at the K West Basin where highly radioactive sludge is stored. Eventually that sand filter will require disposal. The radionuclide content of the solids trapped in the sand filter will affect the selection of the sand filter disposal pathway. The Pacific Northwest National Laboratory (PNNL) was contracted by the K Basin Operations & Plateau Remediation Project (operations contractor CH2M Hill) to analyze the radionuclide content of the solids collected from the backwash of the K West Basin sand filter. The radionuclide composition in the sand filter backwash solids will be used by CH2M Hill to determine if the sand filter media and retained sludge solids will be designated as transuranic waste for disposal purposes or can be processed through less expensive means. On October 19, 2015, K Basin Operations & Plateau Remediation Project staff backwashed the sand filter into the North Load-Out Pit (NLOP) and immediately collected sample slurry from a sampling tube positioned 24 in. above the NLOP floor. The 764 g sand filter backwash slurry sample, KW-105 SFBW-001, was submitted to PNNL for analysis on October 20, 2015. Solids from the slurry sample were consolidated into two samples (i.e., a primary and a duplicate sample) by centrifuging and measured for mass (0.82 g combined – wet centrifuged solids basis) and volume (0.80 mL combined). The solids were a dark brown/orange color, consistent with iron oxide/hydroxide. The solids were dried; the combined dry solids mass was 0.1113 g, corresponding to 0.0146 weight percent (wt%) solids in the original submitted sample slurry. The solids were acid-digested using nitric and hydrochloric acids. Insoluble solids developed upon dilution with 0.5 M HNO3, corresponding to an average 6.5 wt% of the initial dry solids content. The acid digestate and insoluble solids were analyzed separately by gamma spectrometry. Nominally, 7.7% of the 60Co was present

  8. A Laboratory Experiment on the Evolution of a Sand Gravel Reach Under a Lack of Sediment Supply

    Science.gov (United States)

    Orru, C.; Chavarrias, V.; Ferrara, V.; Blom, A.

    2014-12-01

    A flume experiment was conducted to examine the evolution of a sand-gravel reach under a lack of sediment supply. The experimental data are used to validate a numerical sand-gravel model. A bed composed of a bi-modal sediment mixture is installed with a uniform slope and an imposed gradual fining pattern. Initially, the sand fraction gradually increases in streamwise direction until the bed is fully composed of sand. The water discharge and downstream water level were constant, and the sediment feed rate was equal to zero. The experiment was dominated by bed load, partial transport, and a subcritical flow regime was imposed. The flow rate was such that only sand was mobile (partial transport), which led to a coarsening over the upstream reach and a gradual reduction of the sediment transport rate during the experiment. New equipment was used to measure the evolution of the grain size distribution of the bed surface during the experiment over the entire flume using image analysis. In the upstream reach we observed a gradual coarsening over time and the formation of an armour layer, which resulted in a more abrupt transition in grain size of the bed surface. Bed degradation increased in streamwise direction. This is due to the initial streamwise increase in the availability of sand in the bed. The different volume fraction content of sand in the bed allowed for the gravel to sink more in the downstream part of the upstream reach. The sand reach suffered from a larger degradation. Finally, we see one reach dominated by sand, small bedforms, and a small bed slope, and a gravel reach dominated by a larger bed slope.

  9. Capturing phosphates with iron enhanced sand filtration.

    Science.gov (United States)

    Erickson, Andrew J; Gulliver, John S; Weiss, Peter T

    2012-06-01

    Most treatment practices for urban runoff capture pollutants such as phosphorus by either settling or filtration while dissolved phosphorus, typically as phosphates, is untreated. Dissolved phosphorus, however, represents an average 45% of total phosphorus in stormwater runoff and can be more than 95%. In this study, a new stormwater treatment technology to capture phosphate, called the Minnesota Filter, is introduced. The filter comprises iron filings mixed with sand and is tested for phosphate removal from synthetic stormwater. Results indicate that sand mixed with 5% iron filings captures an average of 88% phosphate for at least 200 m of treated depth, which is significantly greater than a sand filter without iron filings. Neither incorporation of iron filings into a sand filter nor capture of phosphates onto iron filings in column experiments had a significant effect on the hydraulic conductivity of the filter at mixtures of 5% or less iron by weight. Field applications with up to 10.7% iron were operated over 1 year without detrimental effects upon hydraulic conductivity. A model is applied and fit to column studies to predict the field performance of iron-enhanced sand filters. The model predictions are verified through the predicted performance of the filters in removing phosphates in field applications. Practical applications of the technology, both existing and proposed, are presented so stormwater managers can begin implementation.

  10. Cleaning oil sands drilling waste in Alberta

    Energy Technology Data Exchange (ETDEWEB)

    Mikic, N.; Nilsen, C.; Markabi, M. [Mi SWACO, Calgary, AB (Canada)

    2008-07-01

    The waste generated from steam assisted gravity drainage (SAGD) wells is brought to the surface and separated by shale shakers. The waste can include drilling fluids and sand contaminated with bitumen. This paper described a new technology developed to treat waste using the addition of hot water and various mixing and separation technologies to reduce the viscosity of the bitumen and separate it from the sand. The bitumen-contaminated drill cuttings were mixed with hot water to form a slurry that was then separated through the G-force created by a hydrocyclone. A secondary separation was then conducted in an elutriation column to remove residual contaminants from the sand. The flow rate of the process was controlled by the fine solids composition of the cuttings, the temperature of the cleaning process, and the performance of the individual components. Laboratory tests conducted to tests the method showed that the sand particles produced using the method were clean enough to be safely disposed in the environment. A pilot study will be conducted to test the sand cleaning technology at a commercial scale. 6 refs., 3 figs.

  11. Dizziness and Motion Sickness

    Science.gov (United States)

    ... ENTCareers Marketplace Find an ENT Doctor Near You Dizziness and Motion Sickness Dizziness and Motion Sickness Patient ... vision or speech, or hearing loss. What is dizziness? Dizziness can be described in many ways, such ...

  12. Characterizing time-dependent contact angles for sands hydrophobized with oleic and stearic acids

    DEFF Research Database (Denmark)

    Subedi, S; Kawamoto, K; Jayarathna, L

    2012-01-01

    -frequency precipitation. A potential solution is to alter soil grain surfaces to become water repellent by mixing or coating the soil cover material with hydrophobic agents (HAs). In this study, hydrophobic CBs comprised of sands mixed with environmentally friendly HAs (oleic acid [OA] and stearic acid [SA]) were studied....... Water repellency (WR) characteristics for hydrophobized sand samples with different HA contents and representing different coating methods (mixing in and solvent aided) were measured. Initial contact angles (αi) for OA-coated samples sharply increased with increasing HA content and reached peak values...

  13. Arsenate removal from water using sand--red mud columns.

    Science.gov (United States)

    Genç-Fuhrman, Hülya; Bregnhøj, Henrik; McConchie, David

    2005-08-01

    This study describes experiments in which sorption filters, filled with chemically modified red mud (Bauxsol) or activated Bauxsol (AB) coated sand, are used to remove As(V) (arsenate) from water. Bauxsol-coated sand (BCS) and AB-coated sand (ABCS) are prepared by mixing Bauxsol or AB with wet sand and drying. Samples of the BCS and ABCS are also used in batch experiments to obtain isotherm data. The observed adsorption data fit the Langmuir model well, with adsorption maxima of 3.32 and 1.64 mgg(-1) at pH values of 4.5 and 7.1, respectively for BCS; and of 2.14 mgg(-1) for ABCS at a pH of 7.1. Test results show that higher arsenate adsorption capacities can be achieved for both BCS and ABCS when using the columns compared to results for batch experiments; the difference is greater for BCS. Additional batch tests, carried out for 21 days using BCS to explain the observed discrepancy, show that the equilibrium time previously used in batch experiments was too short because adsorption continued for at least 21 days and reached 87% after 21 days compared to only 35% obtained after 4h. Fixed bed column tests, used to investigate the effects of flow rate and initial arsenate concentration indicate that the process is sensitive to both parameters, with lower flow rates (longer effective residence times in the columns) and initial arsenate concentrations providing better column performance. An examination of the combined effect of potential competing anions (i.e. silicate, phosphate, sulphate and bicarbonate) on the column performance showed that the presence of these anions in tap water slightly decreases arsenate removal. Each breakthrough curve is compared to the Thomas model, and it is found that the model may be applied to estimate the arsenate sorption capacity in columns filled with BCS and ABCS. The data obtained from both batch and column studies indicate that BCS and ABCS filtration could be effectively used to remove arsenate from water, with the latter being

  14. Dynamic simulation of cable shovel specific energy in oil sands excavation

    Energy Technology Data Exchange (ETDEWEB)

    Awuah-Offei, K. [Missouri-Rolla Univ., Rolla, MO (United States). School of Materials, Energy and Earth Resources; Frimpong, S. [Missouri-Rolla Univ., Rolla, MO (United States). Dept. of Mining Engineering, Mining and Nuclear Engineering; Askari-Nasab, H. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering

    2005-07-01

    Oil sand excavation requires the use cable shovels which constitute one of the major costs in surface mining operations. Random occurrences of shales and limestones within the Athabasca oil sands formation result in varying shovel diggability and stress loading of the boom-crowd-dipper-teeth assembly which reduces digging efficiency. This inefficient use of cable shovels negatively affects the return on capital investment in these otherwise effective machines. In the Athabasca oil sands, varying stress loading has the potential to increase shovel downtime and increase maintenance costs. This paper presented a newly developed cable shovel simulator that uses shovel kinematics and dynamics, dynamic cutting resistance and payload models. It can model the specific energy needed to overcome the resistance to machine motion and material digging. The comprehensive model considers both machine motion and machine-formation interaction forces. It also provides a comprehensive theoretical assessment of shovel performance. The model is useful to mining engineers when examining both the machine operating parameters and material parameters that influence shovel performance. The study showed that bulk density is the most important material property influencing diggability. Operator preferences also influence the specific energy of excavation. 12 refs., 2 tabs., 6 figs.

  15. Sensitivity of growth characteristics of tidal sand ridges and long bed waves to formulations of bed shear stress, sand transport and tidal forcing: A numerical model study

    Science.gov (United States)

    Yuan, Bing; de Swart, Huib E.; Panadès, Carles

    2016-09-01

    Tidal sand ridges and long bed waves are large-scale bedforms that are observed on continental shelves. They differ in their wavelength and in their orientation with respect to the principal direction of tidal currents. Previous studies indicate that tidal sand ridges appear in areas where tidal currents are above 0.5 m s-1, while long bed waves occur in regions where the maximum tidal current velocity is slightly above the critical velocity for sand erosion and the current is elliptical. An idealized nonlinear numerical model was developed to improve the understanding of the initial formation of these bedforms. The model governs the feedbacks between tidally forced depth-averaged currents and the sandy bed on the outer shelf. The effects of different formulations of bed shear stress and sand transport, tidal ellipticity and different tidal constituents on the characteristics of these bedforms (growth rate, wavelength, orientation of the preferred bedforms) during their initial formation were examined systematically. The results show that the formulations for bed shear stress and slope-induced sand transport are not critical for the initial formation of these bedforms. For tidal sand ridges, under rectilinear tidal currents, increasing the critical bed shear stress for sand erosion decreases the growth rate and the wavelength of the preferred bedforms significantly, while the orientation angle slightly decreases. The dependence of the growth rate, wavelength and the orientation of the preferred bedforms on the tidal ellipticity is non-monotonic. A decrease in tidal frequency results in preferred bedforms with larger wavelength and smaller orientation angle, while their growth rate hardly changes. In the case of joint diurnal and semidiurnal tides, or spring-neap tides, the characteristics of the bedforms are determined by the dominant tidal constituent. For long bed waves, the number of anticyclonically/cyclonically oriented bedforms with respect to the principal

  16. Objects in Motion

    Science.gov (United States)

    Damonte, Kathleen

    2004-01-01

    One thing scientists study is how objects move. A famous scientist named Sir Isaac Newton (1642-1727) spent a lot of time observing objects in motion and came up with three laws that describe how things move. This explanation only deals with the first of his three laws of motion. Newton's First Law of Motion says that moving objects will continue…

  17. Permeability Tests on Eastern Scheldt Sand

    DEFF Research Database (Denmark)

    Jakobsen, Kim Parsberg

    The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends on the charact......The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends...... on the characteristics of the soil matrix, the permeability is determined for different void ratios. All tests are performed on reconstituted specimens of Eastern Scheldt Sand. The permeability is determined by use of a falling head apparatus. Finally the test results are briefly summarised and a relationship between...... void ratio and permeability is established....

  18. Sand Dunes Fixation in Baiji District, Iraq

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    This study was carried out at Sand Dunes Stabilization Researches Station in Baiji district (230 ln north of Baghdad, Iraq) to evaluate the effects of local soil conditioners manufactured from oil derivatives and plant residuals on sand dunes fixation as the first step for sand dunes stabilization. The results indicate that the fuel oil has the first place in improving wind erosion parameters in the study area, such as increasing mean weight diameter, dry aggregates percentage, the needed time for complete disaggregation by dry sieving, and decreasing the disaggregation rates. Bitumen emulsion occupies the second place, while the plant residuals occupies the third place and has slight effects on the studied parameters. Effects of conditioners on natural vegetation cover are negative in oil derivatives treatments,while positive in plants residuals treatments.

  19. Thermoluminescent dosimetric properties of Descalvado sand

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, M.I.; Caldas, L.V.E

    2006-07-01

    Sand samples proceeding from Descalvado, Sao Paulo, were studied with regard to their dosimetric properties using the thermoluminescence technique (TL) for high doses. These sand samples present steady physical and chemical characteristics to the end items, and they are used in the glass industry and for casting. The TL curves of the samples were obtained after an irradiation at the Gamma-Cell system ({sup 60} Co), of IPEN. The glow curves present two peaks at 80 C and 220 C approximately. Calibration curves were obtained for doses between 50 Gy and 5 kGy. The results indicate that the sand samples can be used for high-doses dosimetry in several areas of applications of ionizing radiation. (Author)

  20. Development tendencies of moulding and core sands

    Directory of Open Access Journals (Sweden)

    Stanislaw M. Dobosz1

    2011-11-01

    Full Text Available Further development of the technology for making moulding and core sands will be strictly limited by tough requirements due to protection of the natural environment. These tendencies are becoming more and more tense, so that we will reach a point when even processes, that from technological point of view fulfill high requirements of the foundry industry, must be replaced by more ecologically-friendly solutions. Hence, technologies using synthetic resins as binding materials will be limited. This paper presents some predictable development tendencies of moulding and core sands. The increasing role of inorganic substances will be noticed, including silicate binders with significantly improved properties, such as improved knock-out property or higher reclamation strength. Other interesting solutions might also be moulding sands bonded by geo-polymers and phosphate binders or salts and also binders based on degradable biopolymers. These tendencies and the usefulness of these binders are put forward in this paper.

  1. Articulated Human Motion Tracking Using Sequential Immune Genetic Algorithm

    Directory of Open Access Journals (Sweden)

    Yi Li

    2013-01-01

    Full Text Available We formulate human motion tracking as a high-dimensional constrained optimization problem. A novel generative method is proposed for human motion tracking in the framework of evolutionary computation. The main contribution is that we introduce immune genetic algorithm (IGA for pose optimization in latent space of human motion. Firstly, we perform human motion analysis in the learnt latent space of human motion. As the latent space is low dimensional and contents the prior knowledge of human motion, it makes pose analysis more efficient and accurate. Then, in the search strategy, we apply IGA for pose optimization. Compared with genetic algorithm and other evolutionary methods, its main advantage is the ability to use the prior knowledge of human motion. We design an IGA-based method to estimate human pose from static images for initialization of motion tracking. And we propose a sequential IGA (S-IGA algorithm for motion tracking by incorporating the temporal continuity information into the traditional IGA. Experimental results on different videos of different motion types show that our IGA-based pose estimation method can be used for initialization of motion tracking. The S-IGA-based motion tracking method can achieve accurate and stable tracking of 3D human motion.

  2. The growth and photosynthesis of Typha in oil sands process affected material and water

    Energy Technology Data Exchange (ETDEWEB)

    Foote, L. [Alberta Univ., Edmonton, AB (Canada); Hornung, J. [Petro-Canada, Calgary, AB (Canada)

    2007-07-01

    Aquatic plants such as cattail contribute substantially to the energy flow in wetlands. Since Typha (cattail) plants acquire and cycle carbon and nutrients through wetlands, their growth and recycling of captured nutrients are an important part of natural, healthy wetland ecosystems. Cattail are pervasive and satisfy many of the criteria to be used as indicators of wetland integrity. This study investigated if cattail growth and carbon accrual were influenced by oil sands process materials (OSPM) such as consolidated tailings (CT). The purpose was to facilitate land reclamation initiatives by evaluating the impact that constituents of oil sands process material have on aquatic plant growth. The study was conducted at Suncor's experimental trenches. Six lined basins were used, of which 3 were filled with natural water and 3 were filled with trench water. Cattail were planted in different growth medium combinations, including CT over CT; soil over soil; soil over CT; and soil over sterilized sand. All leaf lengths and widths were measured along with the photosynthesis of the leaves and root and plant biomass at planting and after 2-years growth. A larger leaf area was observed under oil sands process influence, which may indicate increased carbon accrual above ground. Leaf area data suggested that CT affected plants are quite productive. The study also indicated that oil sands affected water may reduce plant fitness, and therefore could influence the overall oil sands reclamation timelines. Conversely, cattail grown in soil capped process affected material had a much larger leaf area compared to those grown in soil capped sand, most likely due to the higher levels of ammonia in process affected material.

  3. Intravoxel incoherent motion diffusion-weighted magnetic resonance imaging of focal vertebral bone marrow lesions: initial experience of the differentiation of nodular hyperplastic hematopoietic bone marrow from malignant lesions

    Energy Technology Data Exchange (ETDEWEB)

    Park, Sunghoon; Kwack, Kyu-Sung; Kim, Jae Ho [Ajou University School of Medicine, Division of Musculoskeletal Radiology, Department of Radiology, Suwon, Gyeonggi-do (Korea, Republic of); Ajou University Medical Center, Musculoskeletal Imaging Laboratory, Suwon (Korea, Republic of); Chung, Nam-Su [Ajou University School of Medicine, Department of Orthopaedic Surgery, Suwon (Korea, Republic of); Hwang, Jinwoo [Philips Healthcare, Department of Clinical Science, Seoul (Korea, Republic of); Lee, Hyun Young [Ajou University Medical Center, Regional Clinical Trial Center, Suwon (Korea, Republic of); Yonsei University College of Medicine, Department of Biostatistics, Seoul (Korea, Republic of)

    2017-05-15

    To evaluate the ability of intravoxel incoherent motion (IVIM) diffusion-weighted magnetic resonance imaging (MRI) parameters to differentiate nodular hyperplastic hematopoietic bone marrow (HHBM) from malignant vertebral bone marrow lesions (VBMLs). A total of 33 patients with 58 VBMLs, including 9 nodular HHBM lesions, 39 bone metastases, and 10 myelomas, were retrospectively assessed. All diagnoses were confirmed either pathologically or via image assessment. IVIM diffusion-weighted MRI with 11 b values (from 0 to 800 s/mm{sup 2}) were obtained using a 3.0-T MR imager. The apparent diffusion coefficient (ADC), pure diffusion coefficient (D), perfusion fraction (f), and pseudodiffusion coefficient (D*) were calculated. ADC and IVIM parameters were compared using the Mann-Whitney U test. Receiver operating characteristic (ROC) curve analysis was performed to assess the diagnostic performances of ADC, D, f, and D* in terms of VBML characterization. The diagnostic performance of morphological MR sequences was also assessed for comparison. The ADC and D values of nodular HHBM were significantly lower than those of malignant VBML (both p values < 0.001), whereas the f value was significantly higher (p < 0.001). However, there were no significant differences in D* between the two groups (p = 0.688). On ROC analysis, the area under the curve (AUC) for D was 1.000, which was significantly larger than that for ADC (AUC = 0.902). Intravoxel incoherent motion diffusion-weighted MRI can be used to differentiate between nodular HHBM and malignant VBML. The D value was significantly lower for nodular HHBM, and afforded a better diagnostic performance than the ADC, f, and D* values in terms of such differentiation. (orig.)

  4. Onset of motion at the surface of a porous granular bed by a shearing fluid flow

    Science.gov (United States)

    Hong, Anyu; Tao, Mingjiang; Kudrolli, Arshad

    2014-03-01

    We will discuss an experimental investigation of the onset of particle motion by a fluid flow over an unconsolidated granular bed. This situation arises in a number of natural and industrial processes including wind blowing over sand, sediment transport in rivers, tidal flows interacting with beaches and flows in slurry pipelines and mixing tanks. The Shields criteria given by the ratio of the viscous shear and normal stresses is used to understand the onset of motion. However, reviews reveals considerable scatter while noting broad trends with Reynolds Number. We discuss an idealized model system where fluid flows with a prescribed flow rate through a horizontal rectangular pipe initially fully filled with granular beads. The granular bed height decreases and reaches a constant height when the shear stress at the boundary decreases below a critical value. We compare and contrast the values obtained assuming no-slip boundary conditions with those observed with PIV using florescent tracer particles to measure the actual fluid flow profile near the porous interface. We will also report the observed variation of the Shields criteria with particle Reynolds Number by varying particle size and fluid flow rates.

  5. Undrained Cyclic Behaviour of Dense Frederikshavn Sand

    DEFF Research Database (Denmark)

    Nielsen, Søren Kjær; Ibsen, Lars Bo; Sørensen, Kris Wessel

    2013-01-01

    A modified contour diagram is created for the Frederikshavn Sand in the undrained case for a relative density of ID = 80 %. It can be used to estimate the number of cycles to failure for a given combination of pore pressure, average and cyclic load ratio. The diagram is based on a series of undra......A modified contour diagram is created for the Frederikshavn Sand in the undrained case for a relative density of ID = 80 %. It can be used to estimate the number of cycles to failure for a given combination of pore pressure, average and cyclic load ratio. The diagram is based on a series...

  6. Sand control systems used in completing wells

    Directory of Open Access Journals (Sweden)

    Gabriel Wittenberger

    2005-12-01

    Full Text Available Expandable Tubular Technology is transforming the face of well completion and construction. This technology provides: a substantially higher hydrocarbon production rates from the reservoir, a reduced well drilling and construction costs, new possibilities for previously unreachable or uneconomic reservoirs, and step a change towards the single diameter well. ESS (Expandable Sand Screen has an unrivalled performance worldwide for delivering a reliable sand control in a wide range of applications. Well costs typically cut by over 20 %, and the productivity increases up to 70 %.

  7. On the Size Distribution of Sand

    DEFF Research Database (Denmark)

    Sørensen, Michael

    2016-01-01

    -distribution, by taking into account that individual grains do not have the same travel time from the source to the deposit. The travel time is assumed to be random so that the wear on the individual grains vary randomly. The model provides an interpretation of the parameters of the NIG-distribution, and relates the mean......A model is presented of the development of the size distribution of sand while it is transported from a source to a deposit. The model provides a possible explanation of the log-hyperbolic shape that is frequently found in unimodal grain size distributions in natural sand deposits, as pointed out...

  8. George Sand [Reseña

    OpenAIRE

    Jack, Belinda; Thomas, Florence

    2002-01-01

    Belinda Jack nos cuenta en ese libro la vida de George Sand (de su verdadero nombre Aurora Dupin), esa mujer libertaria del siglo XIX, lo años de su nacimiento, su infancia, su adolescencia y su vida adulta. Una vida tan llena tanto por sus luchas interiores -Sand es una mujer que desde su adolescencia tratará de romper los fatalismos ligados a la condición de mujer del siglo XIX, un siglo profundamente familista y maternalista- como por su inmensa obra literaria que cuenta más de cincuenta n...

  9. Investigation of Sand-Cement Grouts

    Science.gov (United States)

    1960-09-01

    the sianAS. Ho-4, VVers thia 𔃽pacification ,Jlowi -inI r.ver,4 e ofl 3 :*- cen~t to be retain(v,- on1 the NO,. 1E6 sieve. 3y * :.Oviiq- (1),, sc...325 material as does the traprock or silica sand. This j J: i3 -robably the reason for the difference in the quantity of sand founud pmrnable. The three...deficient in material assing th.e ±,e h DOsieve, Ath the addition of percentages of fŕ. ash was test-ilwped. in the other to-ts in this phase, tne

  10. Model test on sand retaining wall reinforced with denti-strip inclusions

    Institute of Scientific and Technical Information of China (English)

    ZHANG MengXi; ZHOU Huai

    2008-01-01

    In conventional reinforced soil structures, the reinforcements are often laid hori-zontally in the soil. In this paper, a new concept of soil reinforced with denti-strip inclusions was proposed and a series of laboratory model tests were carried out on sand retaining wall reinforced with denti-strip inclusions. Besides the horizontal displacements of the facing, the lateral earth pressures acting on vertical elements were measured. A microscopic measurement was performed to investigate the deformation and progressive failure of the sand within model retaining wall. Based on the image analytical technique, the bearing capability and interaction mecha-nism of reinforced sand retaining wall were analyzed. The model of the initial shear failure and potential failure surface were also put forward. From the ex-perimental results, it is shown that denti-strip inclusions can increase the bearing capability of retaining wall significantly and restrict the facing displacements effi-ciently, as compared with conventional horizontal reinforcement.

  11. Air quality over the Alberta oil sands: Satellite observations of NO2 and SO2

    Science.gov (United States)

    McLinden, C. A.; Fioletov, V.

    2011-12-01

    A vast reserve of bitumen - oil mixed with sand, clay, and water generally referred to as oil sands - resides in northern Alberta, Canada. Extraction of bitumen and its upgrade to liquid fuel is very energy intensive and generates significant emissions, including nitrogen and sulphur oxides. Satellite observations of NO2 and SO2 vertical column densities have been used to assess the magnitude and distribution of these pollutants throughout the oil sands. Preliminary results indicate a statistically significant enhancement in both species over an area (~30 x 30 km2) of intensive surface mining. Quantifying the burden of these enhancements and their recent changes over such a small area, comparable to the resolution of the best air quality satellite instruments, represents a significant challenge. The methodology used to meet this challenge will be presented, as will initial results including trends over the past decade, comparisons with other large industrial operations, and an assessment of consistency with emission inventories.

  12. Fabric Behavior of Sand in Post-liquefaction

    Directory of Open Access Journals (Sweden)

    Seyed Amirodin Sadrnejad

    2005-01-01

    Full Text Available An anisotropic plasticity model for post-liquefaction of the undrained behavior of sand is presented. The model incorporates the critical/steady state concept that postulates the existence of a state where sand continuously deforms at a certain constant effective stress depending two main parameters of both initial bulk parameters (void ratio or relative density and the stress level (mean stress. The local instability of saturated sand within post-liquefaction is highly dependent on the residual inherent/induced anisotropy, bedding plane effects and stress/strain path. Most of the models developed using stress/strain invariants are not capable of identifying the parameters depending on orientation such as fabric. This is mainly because stress/strain invariants are quantities similar to scalar quantities and not capable of carrying directional information with them. The constitutive equations of the model are derived within the context of non-linear elastic behavior of the whole medium and plastic sliding of interfaces of predefined multi-planes. The proposed multi-plane based model is capable of predicting the behavior of soils on the basis of plastic sliding mechanisms, elastic behavior of particles and possibilities to see the micro-fabric effects as natural anisotropy as well as induced anisotropy in plasticity. The model is capable of predicting the behavior of soil under different orientation of bedding plane, history of strain progression during the application of any stress/strain paths. The influences of rotation of the direction of principal stress and strain axes and induced anisotropy are included in a rational way without any additional hypotheses. The spatial strength distribution at a location as an approximation of probable mobilized sliding mechanism is proposed as an ellipsoid function built up on bedding plane.

  13. Smoothing Motion Estimates for Radar Motion Compensation.

    Energy Technology Data Exchange (ETDEWEB)

    Doerry, Armin W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-07-01

    Simple motion models for complex motion environments are often not adequate for keeping radar data coherent. Eve n perfect motion samples appli ed to imperfect models may lead to interim calculations e xhibiting errors that lead to degraded processing results. Herein we discuss a specific i ssue involving calculating motion for groups of pulses, with measurements only available at pulse-group boundaries. - 4 - Acknowledgements This report was funded by General A tomics Aeronautical Systems, Inc. (GA-ASI) Mission Systems under Cooperative Re search and Development Agre ement (CRADA) SC08/01749 between Sandia National Laboratories and GA-ASI. General Atomics Aeronautical Systems, Inc. (GA-ASI), an affilia te of privately-held General Atomics, is a leading manufacturer of Remotely Piloted Aircraft (RPA) systems, radars, and electro-optic and rel ated mission systems, includin g the Predator(r)/Gray Eagle(r)-series and Lynx(r) Multi-mode Radar.

  14. Rolling Shutter Motion Deblurring

    KAUST Repository

    Su, Shuochen

    2015-06-07

    Although motion blur and rolling shutter deformations are closely coupled artifacts in images taken with CMOS image sensors, the two phenomena have so far mostly been treated separately, with deblurring algorithms being unable to handle rolling shutter wobble, and rolling shutter algorithms being incapable of dealing with motion blur. We propose an approach that delivers sharp and undis torted output given a single rolling shutter motion blurred image. The key to achieving this is a global modeling of the camera motion trajectory, which enables each scanline of the image to be deblurred with the corresponding motion segment. We show the results of the proposed framework through experiments on synthetic and real data.

  15. Incipient Motion of Sediment Under Currents

    Institute of Scientific and Technical Information of China (English)

    DOU Guoren

    2000-01-01

    Summarized in the paper are the author′s studies on incipient motion of sediment in recent 40years. In addition to the forces of gravity, drag and lift, the cohesive force and the additional static pressure are important for fine particles. The relations between three stages of incipient motion are defined by use of instantaneous velocity. Formulas for initial velocity and critical shear stress are given and overall verified by the author′s and others′ experimental data

  16. A probability density function of liftoff velocities in mixed-size wind sand flux

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    With the discrete element method(DEM) ,employing the diameter distribution of natural sands sampled from the Tengger Desert,a mixed-size sand bed was produced and the particle-bed collision was simulated in the mixed-size wind sand movement. In the simulation,the shear wind velocity,particle diameter,incident velocity and incident angle of the impact sand particle were given the same values as the experimental results. After the particle-bed collision,we collected all the initial velocities of rising sand particles,including the liftoff angular velocities,liftoff linear velocities and their horizontal and vertical components. By the statistical analysis on the velocity sample for each velocity component,its probability density functions were obtained,and they are the functions of the shear wind velocity. The liftoff velocities and their horizontal and vertical components are distributed as an exponential density function,while the angular velocities are distributed as a normal density function.

  17. The mechanisms of electrical heating for the recovery of bitumen from oil sands

    Energy Technology Data Exchange (ETDEWEB)

    McGee, B.C.W. [McMillan-McGee Corp., Edmonton, AB (Canada); Vermeulen, F.E. [Alberta Univ., Edmonton, AB (Canada)

    2004-07-01

    This paper described the Electro-Thermal Dynamic Stripping Process (ET-DSP), a thermal recovery process in which oil sands are electrically heated. This technology has evolved since the 1970s as an alternative to steam assisted gravity drainage (SAGD) and surface mining of Alberta's oil sands. The heat and mass transfer mechanisms associated with electrical heating were examined along with the gravity forces to better understand how the heated bitumen is recovered from the oil sand. Initially, all fluids are immobile. Heat is created in the oil sand as a current flows through the connate water. This results in a pressure and temperature distribution that is characteristic to an electrical heating process. The electrical heating process changes as the temperature of the oil sand increases and as the bitumen is produced. The heat, mass and electromagnetic fields are strongly coupled and are in a transient state throughout the recovery process. This paper presented the main mechanism for electrical heating in terms of equations. A 3-dimensional quasi-harmonic finite element electromagnetic model was coupled to a mass and energy equation and solved in time. A thermal recovery strategy was then presented in terms of electrode spacing, duration of heating, energy supply and ideal operating conditions.

  18. Debris flows on the Great Kobuk Sand Dunes, Alaska: Implications for analogous processes on Mars

    Science.gov (United States)

    Hooper, Donald M.; Dinwiddie, Cynthia L.

    2014-02-01

    We observed niveo-aeolian deposits, denivation features, and small meltwater-induced debris flows that had formed at the Great Kobuk Sand Dunes, northwestern interior Alaska in late March 2010. This high-latitude, cold-climate dune field is being studied as a planetary analog to improve our understanding of factors that may trigger debris flows on the lee slopes of martian aeolian dunes. Debris flows consisted of a sand and liquid water mixture that cascaded down the lee slopes of two barchanoid dunes on days when measured ground surface temperatures were below freezing. We hypothesize that relatively dark sand on snow caused local hot spots where solar radiation could be absorbed by the sand and conducted into the underlying snow, enabling meltwater to form and sand to be mobilized. This investigation provides insights into the interactions between niveo-aeolian deposition, slope aspect and insolation, thawing, and initiation of alluvial processes. These debris flows are morphologically similar to those associated with seasonal gullies or erosion tracks visible on the slopes of mid- to high-latitude dune fields in both martian hemispheres. Localized heating and thawing at scales too small for orbital sensors to identify may yield martian debris flows at current climate conditions.

  19. Structural motion engineering

    CERN Document Server

    Connor, Jerome

    2014-01-01

    This innovative volume provides a systematic treatment of the basic concepts and computational procedures for structural motion design and engineering for civil installations. The authors illustrate the application of motion control to a wide spectrum of buildings through many examples. Topics covered include optimal stiffness distributions for building-type structures, the role of damping in controlling motion, tuned mass dampers, base isolation systems, linear control, and nonlinear control. The book's primary objective is the satisfaction of motion-related design requirements, such as restrictions on displacement and acceleration. The book is ideal for practicing engineers and graduate students. This book also: ·         Broadens practitioners' understanding of structural motion control, the enabling technology for motion-based design ·         Provides readers the tools to satisfy requirements of modern, ultra-high strength materials that lack corresponding stiffness, where the motion re...

  20. MouldingSandDB – a modern database storing moulding sands properties research results

    Directory of Open Access Journals (Sweden)

    J. Jakubski

    2011-01-01

    Full Text Available The complexity of foundry processes requires the use of modern, advanced IT tools for optimization, storage and analysis of t echnicaldata. Properties of moulding and core sands that are collected in research laboratories, manufacturers, and finally in the foundries, are not in use later on. It seems important to create a database that will allow to use the results stored, along with the possibility of searching according to set criteria, adjusted to casting practice. This paper presents part of the database named „MouldingSandDB”, which allows to collect and search data for synthetic moulding sands.

  1. Real-Time Simulation of Aeolian Sand Movement and Sand Ripple Evolution: A Method Based on the Physics of Blown Sand

    Institute of Scientific and Technical Information of China (English)

    Ning Wang; Bao-Gang Hu

    2012-01-01

    Simulation and visualization of aeolian sand movement and sand ripple evolution are a challenging subject.In this paper,we propose a physically based modeling and simulating method that can be used to synthesize sandy terrain in various patterns.Our method is based on the mechanical behavior of individual sand grains,which are widely studied in the physics of blown sand.We accounted significant mechanisms of sand transportation into the sand model,such as saltation,successive saltation and collapsing,while simplified the vegetation model and wind field model to make the simulation feasible and affordable.We implemented the proposed method on the programming graphics processing unit (GPU) to get real-time simulation and rendering.Finally,we proved that our method can reflect many characteristics of sand ripple evolution through several demonstrations.We also gave several synthesized desert scenes made from the simulated height field to display its significance on application.

  2. Thermal diffusivity of peat, sand and their mixtures at different water contents

    Science.gov (United States)

    Gvozdkova, Anna; Arkhangelskaya, Tatiana

    2014-05-01

    Thermal diffusivity of peat, sand and their mixtures at different water contents was studied using the unsteady-state method described in (Parikh et al., 1979). Volume sand content in studied samples was 0 % (pure peat), 5, 10, 15, 20, 30, 40, 50, 55 and 62 % (pure sand). Thermal diffusivity of air-dry samples varied from 0.6×10-7m2s-1 for pure peat to 7.0×10-7m2s-1 for pure sand. Adding 5 and 10 vol. % of sand didn't change the thermal diffusivity of studied mixture as compared with that of the pure air-dry peat. Adding 15 % of sand resulted in significant increase of thermal diffusivity by approximately 1.5 times: from 0.6×10-7m2s-1 to 0.9×10-7m2s-1. It means that small amounts of sand with separate sand particles distributed within the peat don't contribute much to the heat transfer through the studied media. And there is a kind of threshold between the 10 and 15 vol. % of sand, after which the continuous sandy chains are formed within the peat, which can serve as preferential paths of heat transport. Adding 20 and 30 % of sand resulted in further increase of thermal diffusivity to 1.3×10-7m2s-1 and 1.7×10-7m2s-1, which is more than two and three times greater than the initial value for pure peat. Thermal diffusivity vs. moisture content dependencies had different shapes. For sand contents of 0 to 40 vol. % the thermal diffusivity increased with water content in the whole studied range from air-dry samples to the capillary moistened ones. For pure peat the experimental curves were almost linear; the more sand was added the more pronounced became the S-shape of the curves. For sand contents of 50 % and more the curves had a pronounced maximum within the range of water contents between 0.10 and 0.25 m3m-3 and then decreased. The experimental k(θ) curves, where k is soil thermal diffusivity, θ is water content, were parameterized with a 4-parameter approximating function (Arkhangelskaya, 2009, 2014). The suggested approximation has an advantage of clear

  3. The impact of raindrops on sand

    NARCIS (Netherlands)

    de Jong, Rianne

    2017-01-01

    When a raindrop hits a sand bed, it leaves behind a small crater with a mixture of liquid and grains located at the center. This event is frequently observed in nature, but when absent, sprinklers may artificially produce these impacting drops to facilitate irrigation. Also in industry, the interact

  4. Cumulative environmental management and the oil sands

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    In response to concerns regarding the cumulative environmental impacts of oil sands development within the Athabasca oil sands deposit, the government of Alberta established a Regional Sustainable Development Strategy (RSDS) to balance development with environmental protection. The environmental issues identified through the RSDS were addressed by the Cumulative Environmental Management Association (CEMA). CEMA's boundary is the Wood Buffalo region of northeastern Alberta. It identifies existing and future environmental effects in the region and proposes recommendations to regulatory bodies for reducing environmental impacts associated with oil sands development. This presentation outlined some of the 55 stakeholder representatives of CEMA, including Alberta government departments associated with resource development, oil sand developers within the region, and Aboriginal communities and First Nations. These stakeholders provide input on sector priorities and agree on environmental thresholds. Established working groups also address technical and scientific research issues identified in the RSDS such as sustainable ecosystems; surface waters; trace metals and air contaminants; nitrogen oxides and sulphur dioxides; and land reclamation. To date, CEMA has submitted more than 50 reports and has made 4 major environmental recommendations for trace metal management, ecosystem management tools, a framework for acid deposition management, and a landscape design checklist. tabs., figs.

  5. LEARNING ABOUT THE OCEANS FROM SAND

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    As a young geophysicist in the 1980s, Rob Holman attended a conference in San Francisco that included a field trip to a beach. Dr Holman, who grew up inland, stared at the ocean, assessing the strengths of the waves. But when he looked around, everyone else was studying the sand.

  6. Displacement pile installation effects in sand

    NARCIS (Netherlands)

    Beijer-Lundberg, A.

    2015-01-01

    Installation effects govern the post-installation behaviour of displacement piles in sand. These effects are currently not completely understood. Suitable experimental techniques to model these installation effects include field, laboratory and experimental models. In the current thesis a small-scal

  7. Cyclic Triaxial Loading of Cohesionless Silty Sand

    DEFF Research Database (Denmark)

    Sabaliauskas, Tomas; Ibsen, Lars Bo

    2015-01-01

    To engineer efficient structures offshore, we need to extend our knowledge of soil response. Cyclic loading and high water pressure encountered offshore greatly influence cohesionless soil performance. Silty sand from Frederikshavn wind turbine farm was tested using single diameter height samples...

  8. Galveston Island, Texas, Sand Management Strategies

    Science.gov (United States)

    2016-07-01

    68 Figure 28. Jetty segment used for computation of aeolian sand transport. Background photograph 22 May 2012...113 Figure 68 . Total shoreline change after 50 years for 500,000 yd3 placed every 2 years in different locations...The berm at Ft. Myers, FL, was constructed with dredged material from Matanzas Pass. The dredged material contained greater than 10% fines, which

  9. Building Whales in Sand and Mind.

    Science.gov (United States)

    Warner, Carolyn

    1980-01-01

    Describes two-week summer workshops on evolution, adaptation, and behavior of whales, conducted for children by Cold Spring Harbor Whaling Museum (New York), and culminating in creation of life-size sand sculptures of whales. Provides selected list of periodicals, teaching materials, identification guides, records, and societies devoted to whales…

  10. Sand transport, erosion and granular electrification

    DEFF Research Database (Denmark)

    Merrison, J.P.

    2012-01-01

    The transport of granular materials by wind has a major impact on our environment through sand/soil erosion and the generation and transport of atmospheric dust aerosols. Terrestrially the transport of dust involves billions of tons of material every year, influencing the global climate and impac......The transport of granular materials by wind has a major impact on our environment through sand/soil erosion and the generation and transport of atmospheric dust aerosols. Terrestrially the transport of dust involves billions of tons of material every year, influencing the global climate...... can affect grain transport through the generation of intense electric fields and processes of electrostatic assembly. Importantly the transport of sand is characterized by saltation, which is known to be an active process for erosion and therefore a source for dust and sand formation. Using novel...... erosion simulation techniques the link between grain transport rates and erosion rates has been quantified. Furthermore this can be linked to production rates for dust and has been associated with chemical and mineral alteration through a process of mechanical activation of fractured surfaces. This work...

  11. Sand Waves along the Dutch Coast

    NARCIS (Netherlands)

    Verhagen, H.J.

    1989-01-01

    Sand waves, defined as longshore wave-like movements of the shoreline, measured in a horizontal plane, are described along several stretches of the shoreline of The Netherlands. They have a celerity in the order of 50-200 m/yr, a period of 50- 150 years and an amplitude of 30- 500 m. They are found

  12. Building Whales in Sand and Mind.

    Science.gov (United States)

    Warner, Carolyn

    1980-01-01

    Describes two-week summer workshops on evolution, adaptation, and behavior of whales, conducted for children by Cold Spring Harbor Whaling Museum (New York), and culminating in creation of life-size sand sculptures of whales. Provides selected list of periodicals, teaching materials, identification guides, records, and societies devoted to whales…

  13. Sand and Stone%沙与石

    Institute of Scientific and Technical Information of China (English)

    黄川; 孙静

    2006-01-01

    @@ Astory tells that two friends were walking through the desert. During some point of the journey they had an argument, and one friend slapped the other one in the face1. The one who got slapped was hurt, but without saying anything, he wrote in the sand: "TODAY MY BEST FRIEND SLAPPED ME IN THE FACE."

  14. Regional sustainable development strategy for the Athabasca oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Braat, T.; Barrett, R. [Alberta Environment, Edmonton, AB (Canada)

    2003-07-01

    This paper describes the efforts by Alberta Environment to implement a regional sustainable development strategy for the oil sands industry. Alberta Environment gathers the views from industry, government, First Nations and non-governmental organizations on issues regarding cumulative environmental impacts and sustainable industrial development in Alberta's Athabasca oil sands area. This mandate is carried out through a multi-stakeholder partnership initiative called the Cumulative Environmental Management Association (CEMA). CEMA develops environmental management tools, guidelines and objectives to address environmental issues such as acid deposition, trace air pollutants and surface water quality. The NOx/SO{sub 2} Working Group and the Trace Metal and Air Contaminants Working Group of CEMA address air emissions issues. Their recommendations are referred to the appropriate regulatory agency for implementation. The Lakeland Industry and Community Association (LICA) was created in response to expansion of oil and gas production in the Cold Lake area. LICA is a not-for-profit organization that addresses the concerns of residents living near the Lakeland area to ensure that development is conducted in an environmentally responsible manner. The organization is developing regional environmental monitoring programs for soil, air and water. tabs., figs.

  15. Runoff and soil loss characteristics on loess slopes covered with aeolian sand layers of different thicknesses under simulated rainfall

    Science.gov (United States)

    Zhang, F. B.; Bai, Y. J.; Xie, L. Y.; Yang, M. Y.; Li, Z. B.; Wu, X. R.

    2017-06-01

    In the Wind-Water Erosion Crisscross Region of the northern Loess Plateau, parts of loess slopes have been covered by layers of aeolian sand of different thicknesses. Knowledge of soil erosion processes and magnitudes on these slopes is essential to understanding the coupled water-wind erosion processes and to address the resulting downstream coarse sediment problems in the Yellow River. Simulated rainfall (intensity 90 mm h-1) was performed to explore the effects of sand layer thickness on runoff and soil loss from loess slopes covered with different sand layer thicknesses (0, 0.5, 2, 5, 10, 15, 20, and 25 cm). Initial runoff time increased with increasing sand layer thickness, with greater changes occurring for the increases in the thinner (0-5 cm) than for the thicker layers (5-25 cm). Total runoff yield from the sand-covered loess slopes was 18%-55% lower than from the uncovered loess slope and decreased with increasing sand layer thickness. In contrast, total sediment yield was up to 14 times greater from the sand-covered loess slopes than from the uncovered loess slope and rapidly increased with increasing sand layer thickness. During the rainstorm, runoff and soil loss rates exhibited unimodal distributions, and they were related by a positive linear function, both before and after the maximum soil loss rate, that had a high determination coefficient (R2 > 0.8, p qualitative change in runoff and sediment production modes, appeared to be in the range of 5-10 cm. These results indicated that the thickness of the sand layer on the loess slope significantly influenced runoff and sediment production processes and mechanisms. These effects should be considered when assessing and predicting soil losses in this region and from similar slopes elsewhere.

  16. Dark grains of sand: a geological storytelling

    Science.gov (United States)

    Gallo Maresca, Magda

    2017-04-01

    In the secondary Italian school the Earth science learning begins at first year, in synergy with other natural science subjects such as Astronomy, Chemistry and Biology. Italian teachers have to focus on the landscape geomorphological aspects and often Earth processes are difficult to display since they are related to certain phenomena happened during the past and often far from the involved country. In order to better understand the environment surrounding us, very simple and poor materials, like sands, allow the teachers to create attractive lab experiences. According to the IBSE (Inquiry Based Science Education) approach, a learning unit has been implemented starting from a walking along the light carbonate beaches of the Adriatic sea: a smart look to the sands ("engage step"), stroke the students fantasy pushing them to explore some strange black grains on the sands. Dirty sands? Or rock landscape, soil degradation and Ofanto river and coastal processes (erosion, transportation and deposition)? This was the teaching challenge. Due to the youngest age, a third level, guided inquiry, was adopted so the teacher is the "guide of inquiry" encouraging the students using the research question ("Why is the sand dark?", "Do all sands look the same?", "Where does it come from?") and driving the students around their investigation plans ("How can I measure grain size?"). A procedure to answer the above questions and validate the results and explanations has been implemented to allow the students to be proactive in their study. During the learning activities will be the students to ask for field trip to elaborate their new knowledge, verify and visualize the speculated processes. The teaching skills allow to address several geosciences domains such as mineralogy, petrology, regional geology and geodynamics as well as other scientific disciplines such as mathematics (more specifically statistics), forensic science and even life sciences (the presence of bioclasts might

  17. Assessing environmental impacts of inland sand mining in parts of ...

    African Journals Online (AJOL)

    Assessing environmental impacts of inland sand mining in parts of Ogun State, Nigeria. ... Sand is a valuable resource for construction and other purposes, however ... Natural resources particularly, land, water quality and quantity, air quality, ...

  18. Fiber-reinforced sand strength and dilation characteristics

    Directory of Open Access Journals (Sweden)

    Hesham M. Eldesouky

    2016-06-01

    Full Text Available Randomly distributed fiber reinforcement is used to provide an isotropic increase in the sand shear strength. The previous studies were not consistent regarding the fibers effect on the volumetric change behavior of fiber-reinforced sand. In this paper, direct shear tests are conducted on 108 specimens to investigate the effects of the fibers content, relative density, normal stress and moisture content on the shear strength and volumetric change behaviors of fiber-reinforced sand. The study investigates also the possibility of using dry fiber-reinforced sand as an alternative to heavily compacted unreinforced moist sand. The results indicate that the fibers inclusion increases the shear strength and dilation of sand. Moisture suppresses the fibers effect on the peak and post-peak shear strengths, and dilation. Dry loose fiber-reinforced sand achieves the same shear strength of heavily compacted unreinforced moist sand, yet at more than double the horizontal displacement.

  19. Gating Technology for Vertically Parted Green Sand Moulds

    DEFF Research Database (Denmark)

    Larsen, Per

    Gating technology for vertically parted green sand moulds. Literature study of different ways of designing gating systems.......Gating technology for vertically parted green sand moulds. Literature study of different ways of designing gating systems....

  20. Theoretical Exploration of Exponential Heat Source and Thermal Stratification Effects on The Motion of 3-Dimensional Flow of Casson Fluid Over a Low Heat Energy Surface at Initial Unsteady Stage

    Directory of Open Access Journals (Sweden)

    Sandeep N.

    2017-06-01

    Full Text Available Within the last few decades, experts and scientists dealing with the flow of non-Newtonian fluids (most especially Casson fluid have confirmed the existence of such flow on a stretchable surface with low heat energy (i.e. absolute zero of temperature. This article presents the motion of a three-dimensional of such fluid. Influence of uniform space dependent internal heat source on the intermolecular forces holding the molecules of Casson fluid is investigated. It is assumed that the stagnation flow was induced by an external force (pressure gradient together with impulsive. Based on these assumptions, variable thermophysical properties are most suitable; hence modified kinematic viscosity model is presented. The system of governing equations of 3-dimensional unsteady Casson fluid was non-dimensionalized using suitable similarity transformation which unravels the behavior of the flow at full fledge short period. The numerical solution of the corresponding boundary value problem (ODE was obtained using Runge-Kutta fourth order along with shooting technique. The intermolecular forces holding the molecules of Casson fluid flow in both horizontal directions when magnitude of velocity ratio parameters are greater than unity breaks continuously with an increase in Casson parameter and this leads to an increase in velocity profiles in both directions.

  1. Theoretical Exploration of Exponential Heat Source and Thermal Stratification Effects on The Motion of 3-Dimensional Flow of Casson Fluid Over a Low Heat Energy Surface at Initial Unsteady Stage

    Science.gov (United States)

    Sandeep, N.; Animasaun, I. L.

    2017-06-01

    Within the last few decades, experts and scientists dealing with the flow of non-Newtonian fluids (most especially Casson fluid) have confirmed the existence of such flow on a stretchable surface with low heat energy (i.e. absolute zero of temperature). This article presents the motion of a three-dimensional of such fluid. Influence of uniform space dependent internal heat source on the intermolecular forces holding the molecules of Casson fluid is investigated. It is assumed that the stagnation flow was induced by an external force (pressure gradient) together with impulsive. Based on these assumptions, variable thermophysical properties are most suitable; hence modified kinematic viscosity model is presented. The system of governing equations of 3-dimensional unsteady Casson fluid was non-dimensionalized using suitable similarity transformation which unravels the behavior of the flow at full fledge short period. The numerical solution of the corresponding boundary value problem (ODE) was obtained using Runge-Kutta fourth order along with shooting technique. The intermolecular forces holding the molecules of Casson fluid flow in both horizontal directions when magnitude of velocity ratio parameters are greater than unity breaks continuously with an increase in Casson parameter and this leads to an increase in velocity profiles in both directions.

  2. PRELIMINARY STUDY OF FISH CULTURE IN ABANDONED SAND MINING POOL

    Directory of Open Access Journals (Sweden)

    Bambang Gunadi

    2006-12-01

    Full Text Available One of main problems in freshwater aquaculture development in Indonesia, especially in Java, is unavailability of developing zone. It is important to find an underutilized area that meets for industrial scale freshwater aquaculture, i.e. sufficient water supply, wide area, and located in one area or zone. The abandoned mining (sand, tin, etc. pools distributed along the country might be the potential area for freshwater aquaculture business. For example, there are at least 13 water pools with total surface area of 250 ha at 15 km side of Citarum River in Karawang District (West Java Province. This study was conducted to obtain preliminary data about the prospect and potency of fish culture (tilapia, clariid catfish, and ‘patin’ catfish in abandoned sand-mining pools in Karawang District. Mini floating net cages of 1 x 1 x 1.5 m3 size were used for culturing fish, i.e. patin catfish (Pangasianodon hypophthalmus, nile tilapia (Oreochromis niloticus, and clariid catfish (Clarias gariepinus, separately. Patin catfish were stocked at a size of 2 g with a density of 300 fish per cage, tilapia were stocked at a size of 6 g with a density of 400 fish per cage, while  the clariid catfish were stocked at a size of 1.4 g with a density of 980 fish per cage. A floating commercial feed (30%—32% protein, 3%—5% fat was used at a daily rate of 9% biomass weight at the beginning and reduced gradually to 3% at the final culture period. Observed data showed that patin catfish grew from the initial size of 2.08 g to the final size 299.59 g in 5 months, nile tilapia grew from individual initial size of 5.92 g to the final size of 247.12 g in 14 weeks, and clariid catfish grew from initial size of 1.39 g to the final size of 73.10 g in 8 weeks. These three species were technically prospective for aquaculture development in the abandoned sand-mining pools.

  3. Expandable sand screens: from novel concept to proven sand control technique

    Energy Technology Data Exchange (ETDEWEB)

    Metcalfe, Paul; Jones, Colin; Ballard, Tracey; Beare, Steve; Hillis, Dave [Weatherford International Inc., Houston, TX (United States)

    2004-07-01

    Expandable Sand Screens (ESS) have proved a viable alternative to gravel packing for sand control. With over 300 installations worldwide, analysis of their use has confirmed that ESS offers excellent production performance and sand control reliability in Open hole. This paper presents details of a global survey on ESS performance that gives accurate information on production performance, sand exclusion reliability and cost effectiveness in Open hole and cased hole application scenarios. This paper also discusses the role and effect of compliant expansion in observed productivity performance and skin values. The rock mechanical, reservoir characterization and metallurgical requirements of ESS systems are also investigated. Finally, the latest advances of the technology for use within the reservoir are explained. This paper demonstrates how the combination of ESS and Expandable Zonal Isolation devices can offer cased hole functionality (in terms of zonal isolation) in combination with Open hole levels of production performance (from the ESS). (author)

  4. Water management in the oil sands industry

    Energy Technology Data Exchange (ETDEWEB)

    Pauls, R. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

    2004-07-01

    Water management issues at Alberta's 4 oil sand deposits were discussed. The 4 deposits include the Peace River, Athabasca, Wabasca and Cold Lake deposits, with the Athabasca deposit being the largest and the only surface-mineable deposit. Large quantities of water are needed to extract bitumen from oil sands. This paper addressed water volume withdrawal from the Athabasca River, the primary source of water for the surface-mining oil sands industry. It also addressed Muskeg River watershed integrity, quality of water withdrawn from reclaimed landscapes, groundwater contamination, and ecological viability of end-pit lakes. Currently, half of Syncrude's oil sand is transported from mine to extraction plant by conveyor belts. The other half is pipelined as a warm water slurry. By 2005, all transport will be by pipeline. The oil sand is mixed with hot water, steam and surfactants to condition it for extraction. Seventy-nine per cent of the water used by Syncrude is recycled water and the remainder comes from the Athabasca River. Syncrude diverts 2.5 to 3 barrels of water from the Athabasca River for every barrel of oil produced. This paper discussed the in-stream flow needs of the Athabasca River based on protection of aquatic ecosystems. Flow needs are addressed by the Cumulative Effects Management Association (CEMA). The paper states that the proportion of annual flow withdrawn from the Athabasca River is too low to have a significant impact on aquatic systems, but the main concern lies in water use during low flow periods, typically during the winter months. Developers will likely come under pressure to develop off-site reservoirs to store water for use during these low-flow periods. tabs., figs.

  5. Effect of walking on sand on gait kinematics in individuals with multiple sclerosis.

    Science.gov (United States)

    van den Berg, Maayken E L; Barr, Christopher J; McLoughlin, James V; Crotty, Maria

    2017-08-01

    Walking in the real-world involves negotiating challenging or uneven surfaces, including sand. This can be challenging for people with Multiple Sclerosis (PWMS) due to motor deficits affecting the lower extremities. The study objective was to characterise kinematic gait adaptations made by PWMS when walking on sand and describe any immediate post-adaptation effects. 17 PWMS (mean age 51.4 ± 5.5, Disease Steps 2.4 ± 1.0), and 14 age-and gender matched healthy adults (HA) took part in a case-control study. 3D gait analysis was conducted using an eight-camera Vicon motion capture system. Each participant completed walking trials over level ground (baseline), sand (gait adaptation response), and again level ground (post-adaptation). Spatiotemporal data and kinematic data for the hip knee and ankle were recorded. At baseline PWMS showed significantly less total lower limb flexion (p<0.05) compared to HA. PWMS adapted to walking on sand by significantly increasing hip and knee flexion and ankle dorsiflexion (p<0.05) during swing, resulting in an overall 23° greater total lower limb flexion (p<0.05), reaching values within normal range. During the return to level ground walking values of temporal-spatial and kinematic parameters returned towards baseline values. PWMS adapted to walking on sand by increasing lower limb flexion during swing, and returned to their gait pattern to near baseline levels, in a manner similar to but with values not equalling HA. Further work is required to determine whether this mode of walking has potential to act as a gait retraining strategy to increase flexion of the lower limb. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. WMO Sand and Dust Storm Warning Advisory and Assessment System (SDS-WAS): Research Implementation Status

    Science.gov (United States)

    Nickovic, Slobodan; Barrie, Leonard

    2010-05-01

    Strong winds cause lifting of large amounts of sand and dust from bare, dry soils into the atmosphere. For countries in and downwind of arid regions, airborne sand and dust presents serious risks to the environment, property and human health. Impacts on health include respiratory and cardio-vascular problems, eye infections and in some regions, diseases such as meningitis and valley fever. Dust can efficiently carry irritating spores, bacteria, viruses and persistent organic pollutants. It can also efficiently transport nutrients to parts of the world oceans and affect marine biomass production. Other impacts include negative effects on the ground transport, aviation, agriculture and visibility. The Inter-governmental Panel on Climate Change (IPCC) recognizes dust as a major component of the atmospheric aerosol that is an essential climate variable. Dust aerosol has important effects on weather through feedback on atmospheric dynamics, clouds and precipitation formation. Approximately 15 centres around the world provide sand and dust research operational forecasts. Many are operated by national meteorological services of the World Meteorological Organization (WMO). Sand and dust storm models can substantially reduce risk by providing dust concentration predictions for several days in advance. Numerical weather prediction systems that drive these models use complex parameterizations and assimilation of satellite, and surface-based observations to predict winds, clouds, precipitation and dust mobilization, transport, and removal from the atmosphere. Sand and dust forecast products contribute to the mitigation and reduction of risk through research based advances in understanding and forecasting products. Observations of sand and dust are made by many agencies and some of them are being coordinated globally through the WMO Global Atmosphere Watch (GAW) programme. In 2006, WMO and partners initiated the implementation of the Sand and Dust Storm Warning Advisory and

  7. Optical and radiocarbon ages of stacked paleosols and dune sands in the Nebraska Sand Hills, USA

    Science.gov (United States)

    Goble, R. J.; Mason, Joseph A.; Loope, David B.; Swinehart, James B.

    2004-05-01

    Optical ages for eolian sands from the Nebraska Sand Hills indicate periods of extensive eolian activity at ca 115±25, 840±70, 2300±240, and 3560±340 a. Activity was also noted at single sampling locations at ca 6180±370, 8430±510 and 13110±800 a. Many of these ages are similar to those noted by earlier authors. Optical ages from samples collected within paleosols indicate shorter and possibly less extensive periods of eolian activity at approximately 1220±150, 1590±110, and possibly 1950±150 a, during which the paleosol sands accumulated. What was originally interpreted as a single 1.2 m thick paleosol is shown by optical dating to consist of three or more welded soils developed within eolian sands with optical ages of ca 3800±240, 2740±240, 1560±110, and possibly 1930±140 a, each of which match eolian pulses recognized elsewhere. Scatter in some optical ages is attributable to intersection of sand-filled rodent burrows extending in outcrop 1.5 m below the contact between paleosol and overlying topset beds. A 5310±360 a optical age for one probable intersected burrow provides evidence for upward or lateral transport of older sands.

  8. Evaluate of head loss, sediment value and copper removal in sand media (rapid sand filter

    Directory of Open Access Journals (Sweden)

    Daneshi Navab

    2014-06-01

    Full Text Available Along with the technology development and increasing consumption of water resources, we are experiencing low qualities in the mentioned resources. Copper brings about serious environment al pollution, threatening human health and ecosystem. This metal found variously in water resources and industrial activities. Therefore, it needs to treat the water resources from these excessive amounts. Different methods have used for this reason but the most used method during recent years has been the absorption by economic absorbers such as sand. Rapid sand filters usually used in water and wastewater treatment plants for water clarification. In this research, a single layer gravity rapid sand filter has used to reduce different concentrations of copper. sediment value and head loss arising in filter media is simulated by using combination of Carman-Kozeny, Rose and Gregory models in different discharges of rapid sand filter. Results have shown that with increasing in discharge and decreasing in input copper concentration, arriving time to given head loss, is increasing. In addition, results demonstrated that with increasing in copper concentration in influent, removal efficiency is decreasing somewhat. Results of this research can applied in an appropriate design of rapid sand filter to copper removal, a prediction of rapid sand filter ability to copper removal and an estimation of arising head loss during filter work thus evaluating of time interval backwash. DOI: http://dx.doi.org/10.3126/ije.v3i2.10641 International Journal of the Environment Vol.3(2 2014: 276-286

  9. Yield of a Choctawhatchee Sand Pine Plantation at Age 28

    Science.gov (United States)

    Russell M. Burns; R.H. Brendemuehl

    1969-01-01

    A little-known tree, Choctawhatchee sand pine (Pinus clausa [Chapm.] Vasey), seems well adapted to the infertile, droughty soils common to the sandhills of Florida which now produce little value. Published yield data based on plantation-grown Choctawhatchee sand pine are not available. One 28-year-old plantation of this race of sand pine, growing...

  10. 77 FR 75007 - Importation of Sand Pears From China

    Science.gov (United States)

    2012-12-19

    ... Health Inspection Service 7 CFR Part 319 RIN 0579-AD42 Importation of Sand Pears From China AGENCY... and vegetables regulations to allow the importation of sand pears (Pyrus pyrifolia) from China into the United States. As a condition of entry, sand pears from areas in China in which the Oriental...

  11. Design and management of conventional fluidized-sand biofilters

    Science.gov (United States)

    Fluidized sand biofilters (FSBs) are relatively compact, efficient, and cost-competitive biofilters, especially in recirculating systems that require maintaining consistently low levels of ammonia and nitrite. Filter sand is low cost (often $70-200/m3 of sand delivered) and has a high specific surf...

  12. A new approach to the management of cumulative environmental impacts, the Alberta Oil Sands area

    Energy Technology Data Exchange (ETDEWEB)

    Weagle, K.V. [Cumulative Environmental Association, Wood Buffalo, AB (Canada)

    2002-06-01

    Resource development in the oil sand industry of Northeastern Alberta is enjoying a wave of renewed interest fuelled in part by changes made in the tax and royalty structure for oil sands developments in the province, the development of new technology and the price of oil. Announcements were made of investments totalling approximately 51 billion dollars in the oil sand industry over the next ten years in all deposits. The issue of cumulative environmental effects has been amplified accordingly. In June 2000, an association was formed, the Cumulative Environmental Management Association (CEMA), consisting of stakeholders and based on consensus, with a mandate to address 72 issues related to potential cumulative impacts in the expanded development of the Wood Buffalo Region. Five working groups were formed, as well as three standing committees. To mitigate the cumulative effects, the working groups and standing committees are working on management objectives, management systems and research recommendations. The regulatory bodies receive the recommendations, and the implementation process involves the issuance of permits and licenses. Research and monitoring activities play a vital role in the environmental management system and are part of other current environmental initiatives. Some of the initiatives are managed by the Wood Buffalo Environmental Association, Regional Aquatics Monitoring Program, and the Canadian Oil Sands Network for Research and Development. These organizations touch on topics including air quality monitoring, aquatics monitoring and environmental research. 1 fig.

  13. Closing the performance gap : the challenge for cumulative effects management in Alberta's Athabasca oil sands region

    Energy Technology Data Exchange (ETDEWEB)

    Kennett, S.A. [Calgary Univ., AB (Canada). Canadian Inst. of Resources Law

    2007-05-15

    This paper examined cumulative effects management strategies adopted by the Cumulative Environmental Management Association (CEMA) and the Regional Sustainable Development Strategy (RSDS), multi-stakeholder collaborations established after a set of public hearings conducted before Alberta's Energy and Utilities Board (EUB) in 1997. The initiatives were designed to examine challenges related to the management of cumulative effects of large-scale oil sands developments. However, the scale, pace, and intensity of oil sands development has now exceeded initial expectations, and concerns have been expressed over the inability of the initiatives to adequately address cumulative effects management issues. Stakeholders involved in the initiatives have also expressed doubts over the ability of the initiatives to achieve tangible results. This paper provided details of 16 interviews conducted with participants in CEMA as well as a variety of industry members, and government agencies. Respondents indicated that CEMA's performance gap was caused by the complexity of issues related to cumulative effects management, deficiencies in the initiative's organizational processes, and divergence between participants on objectives. Approaches to narrowing CEMA's performance gap must consider the rapid pace of oil sands development and the significant obstacles to cumulative effects management within legal, institutional, and policy structures. It was concluded that intense conflict around oil sands development is likely if CEMA's performance gaps are not addressed. refs.

  14. Measurement of visual motion

    Energy Technology Data Exchange (ETDEWEB)

    Hildreth, E.C.

    1984-01-01

    This book examines the measurement of visual motion and the use of relative movement to locate the boundaries of physical objects in the environment. It investigates the nature of the computations that are necessary to perform this analysis by any vision system, biological or artificial. Contents: Introduction. Background. Computation of the Velocity Field. An Algorithm to Compute the Velocity Field. The Computation of Motion Discontinuities. Perceptual Studies of Motion Measurement. The Psychophysics of Discontinuity Detection. Neurophysiological Studies of Motion. Summary and Conclusions. References. Author and Subject Indexes.

  15. Brain Image Motion Correction

    DEFF Research Database (Denmark)

    Jensen, Rasmus Ramsbøl; Benjaminsen, Claus; Larsen, Rasmus

    2015-01-01

    The application of motion tracking is wide, including: industrial production lines, motion interaction in gaming, computer-aided surgery and motion correction in medical brain imaging. Several devices for motion tracking exist using a variety of different methodologies. In order to use such devices...... offset and tracking noise in medical brain imaging. The data are generated from a phantom mounted on a rotary stage and have been collected using a Siemens High Resolution Research Tomograph for positron emission tomography. During acquisition the phantom was tracked with our latest tracking prototype...

  16. Seismic reflection characteristics of fluvial sand and shale interbedded layers%河流相砂泥岩薄互层地震反射特征研究

    Institute of Scientific and Technical Information of China (English)

    李国发; 熊金良; 周辉; 翟通利

    2008-01-01

    A sedimentary geological model is established in order to study the seismic reflection characteristics of channel sand bodies. Synthetic seismic shot gathers are simulated using the acoustic wave equation and then are prestack time migrated. On the imaged data,the reflection characteristics and instantaneous attributes are analyzed and log-constrained impedance inversion is tested. Because of wave field interference, the experimental results show that seismic events do not definitely correspond to the channel sand bodies and that seismic modes of occurrence do not represent the actual ones. The seismic events formed by wave interference may lead to errors and pitfalls in sand body interpretation. The corresponding relations between instantaneous seismic attributes and sedimentary sands are not well established. Log-constrained impedance inversion improves the resolution of channel sands. However, if the inverted resolution is forced to be too high, artifacts related to the initial model may occur.

  17. Effect of initiative healing on motion function and ADL in patient with hemiplegia after stroke YANG%主动康复与传统康复对脑卒中偏瘫患者运动功能与日常生活活动能力恢复的比较

    Institute of Scientific and Technical Information of China (English)

    杨坚; 秦杰; 乔蕾; 沈俊; 范利; 李洪丽

    2009-01-01

    目的 探讨主动康复训练与传统康复训练对脑卒中偏瘫患者运动功能与日常生活能力恢复的比较.方法 对60例发病2~12周的脑卒中偏瘫患者,随机分组成主动康复训练组(A组)和传统康复训练组(B组),两组的常规内科治疗相同,分别于入组时、治疗4周末,采用简化Fugl-Meyer运动功能量表、功能独立性评定表(Functional Independence Measure,FIM)进行评定,并作临床疗效评定与总结.结果 治疗4周后A组的各项评分明显高于B组(P<0.0001).结论 主动康复训练较传统康复训练能更明显地改善脑卒中偏瘫患者肢体运动功能与日常生活活动能力.%Objective To observer the effect of individual initiative healing on motion function in patient with hemiplegia after stroke.Methods Sixty patients with hemiplegia after stroke for 2 to 12 weeks were recruited in this study and randomly divided into 2 groups:a initiative healing group(group A)and a passive healing group(group B).Both of the two group had the same general medicine therapy.Assess the two group through simplified Fugl-Meyer motion function table and FIM separately at the time of begin and 4 weeks later and evaluated the clinic curative effect.Results Each assessment of the group A was higher than the group B after 4 weeks'healing.There were significant differences between the two groups(P<0.0001).Conclusion Initiative healing is more effectively than passive healing on motion function and ability of daily living in patient with hemiplegia after stroke.

  18. Numerical Simulation Analysis of Response Law of Wind-blown Sand Flow around Wind-break Wall in Gobi Area%风沙流对戈壁地区挡风墙响应规律的数值模拟分析

    Institute of Scientific and Technical Information of China (English)

    李晓军; 蒋富强

    2016-01-01

    Numerical Simulation of the motion characteristics of wind-blown sand flow around the existing wind-break wall along Lanzhou-Urumqi Railway based on FLUENT eulerian two-fluid model is conducted to identify the distribution features of the flow field and accumulated sand at the leeward side of wind-break. The results show that, wind profile change law shows an exponential increasing tendency at the leeward side of wind-break wall, the changes at the height of 0. 5 m to wind-break wall itself are complex and tend to decrease and then increase;the airflow velocity on near-surface at the leeward side of wind-break wall is increased in the reserve direction, reduced to 0 along the direction of the initial velocity, continued to increase to the initial velocity, and the maximum wind speed increase rate remains at about 50%, the higher the wind speed, the more obvious the airflow of weakening effect; when the initial velocity is small, less sand is accumulated on the line, and sand accumulation is concentrated at the corner of the leeward side of wind-break wall; with the increase of wind speed, more sand passes through the windbreak in unit time and even more sand is deposited along the line due to the reduction of flow cross-section and diffusion of air; in strong wind areas, the surface conditions affecting wind direction should be investigated before wind-break wall is located, engineering measures should be taken where sand source is rich to reduce sand flow density and prevent sand invasion.%基于FLUENT欧拉双流体模型,对兰新铁路沿线既有挡风墙周围风沙两相流运动特性进行数值模拟,得到挡风墙背风侧的流场分布特点以及积沙情况。结果表明:挡风墙背风侧风速廓线变化规律呈指数增长趋势,在0.5 m至挡风墙自身高度区间内变化较为复杂,呈先减小后增加的趋势;挡风墙背风侧近地表气流速度反向增大后沿着初始速度的方向减小为0且继续增大至初

  19. Motion compensator for holographic motion picture camera

    Science.gov (United States)

    Kurtz, R. L.

    1973-01-01

    When reference beam strikes target it undergoes Doppler shift dependent upon target velocity. To compensate, object beam is first reflected from rotating cylinder that revolves in direction opposite to target but at same speed. When beam strikes target it is returned to original frequency and is in phase with reference beam. Alternatively this motion compensator may act on reference beam.

  20. Longshore sediment transport at Golden Sands (Bulgaria

    Directory of Open Access Journals (Sweden)

    Hristo Nikolov

    2006-09-01

    Full Text Available The paper presents the results of studies on the qualitative and quantitative features of the littoral drift at Golden Sands (Bulgaria, carried out jointly by Polish and Bulgarian researchers. The mathematical modelling of physical coastal processes took wave transformation (wave diffraction and refraction; the effects of shoaling and wave breaking and longshore sediment transport into account. The computations were carried out for the mean statistical annual wave climate, determined on the basis of IO BAS wave data, simulated using the WAM method from long-term Black Sea wind data. The results of sediment transport computations clearly show that its direction off the Golden Sands shore is from north to south.

  1. Post-liquefaction reconsolidation of sand.

    Science.gov (United States)

    Adamidis, O; Madabhushi, G S P

    2016-02-01

    Loosely packed sand that is saturated with water can liquefy during an earthquake, potentially causing significant damage. Once the shaking is over, the excess pore water pressures that developed during the earthquake gradually dissipate, while the surface of the soil settles, in a process called post-liquefaction reconsolidation. When examining reconsolidation, the soil is typically divided in liquefied and solidified parts, which are modelled separately. The aim of this paper is to show that this fragmentation is not necessary. By assuming that the hydraulic conductivity and the one-dimensional stiffness of liquefied sand have real, positive values, the equation of consolidation can be numerically solved throughout a reconsolidating layer. Predictions made in this manner show good agreement with geotechnical centrifuge experiments. It is shown that the variation of one-dimensional stiffness with effective stress and void ratio is the most crucial parameter in accurately capturing reconsolidation.

  2. Three dimensional fabric evolution of sheared sand

    Energy Technology Data Exchange (ETDEWEB)

    Hasan, Alsidqi; Alshibli, Khalid (UWA)

    2012-10-24

    Granular particles undergo translation and rolling when they are sheared. This paper presents a three-dimensional (3D) experimental assessment of fabric evolution of sheared sand at the particle level. F-75 Ottawa sand specimen was tested under an axisymmetric triaxial loading condition. It measured 9.5 mm in diameter and 20 mm in height. The quantitative evaluation was conducted by analyzing 3D high-resolution x-ray synchrotron micro-tomography images of the specimen at eight axial strain levels. The analyses included visualization of particle translation and rotation, and quantification of fabric orientation as shearing continued. Representative individual particles were successfully tracked and visualized to assess the mode of interaction between them. This paper discusses fabric evolution and compares the evolution of particles within and outside the shear band as shearing continues. Changes in particle orientation distributions are presented using fabric histograms and fabric tensor.

  3. Rational approach to anisotropy of sand

    Science.gov (United States)

    Wu, Wei

    1998-11-01

    The paper presents a constitutive model for the three-dimensional deformation-strength behaviour of inherently anisotropic sand. Based on non-linear tensorial functions, the model is developed without recourse to the concepts in plasticity theory such as yield surface and plastic potential. Benefited from the fact that no decomposition of strain into elastic and plastic parts is assumed, a unified treatment of anisotropic behaviour of deformation and strength is achieved. Anisotropy is characterized by a vector normal to the bedding plane. The extension of the constitutive model is furnished by incorporating the vector under consideration of the principle of objectivity and the condition of material symmetry. Distinct features of the model are its elegant formulation and its simple structure involving few material parameters. Model performance and comparison with experiments show that the model is capable of capturing the salient behaviour of anisotropic sand.

  4. Bioaugmentation of flow-through sand filters

    DEFF Research Database (Denmark)

    Samuelsen, Elin Djurhuus

    Global applications of pesticides in agricultural production have led to the detection of trace amounts of pesticides in groundwater resources in levels exceeding the EU threshold limit for drinking water of 0.1 µg L-1. Pesticide-polluted groundwater may be remediated by inoculating waterworks sand...... filters with specific degrading bacteria. However, degradation efficiency is often hampered by poor adhesion and a lack of sustained catabolic activity of the introduced bacteria. The overall objective of this thesis was to investigate the significance of selected bacterial surface properties...... coincided with efficient mineralisation/degradation, and proposed the tfdC gene as a suitable marker for monitoring phenoxy acid degradation in strain PM2. Furthermore, when testing strain PM2s degradation performance in flow-through sand columns, we found that strain PM2 was able to sustain induced...

  5. Controlling the motion of multiple objects on a Chladni plate

    Science.gov (United States)

    Zhou, Quan; Sariola, Veikko; Latifi, Kourosh; Liimatainen, Ville

    2016-09-01

    The origin of the idea of moving objects by acoustic vibration can be traced back to 1787, when Ernst Chladni reported the first detailed studies on the aggregation of sand onto nodal lines of a vibrating plate. Since then and to this date, the prevailing view has been that the particle motion out of nodal lines is random, implying uncontrollability. But how random really is the out-of-nodal-lines motion on a Chladni plate? Here we show that the motion is sufficiently regular to be statistically modelled, predicted and controlled. By playing carefully selected musical notes, we can control the position of multiple objects simultaneously and independently using a single acoustic actuator. Our method allows independent trajectory following, pattern transformation and sorting of multiple miniature objects in a wide range of materials, including electronic components, water droplets loaded on solid carriers, plant seeds, candy balls and metal parts.

  6. Analysis of Wind-blown Sand Movement over Transverse Dunes

    Science.gov (United States)

    Jiang, Hong; Huang, Ning; Zhu, Yuanjian

    2014-12-01

    Wind-blown sand movement often occurs in a very complicated desert environment where sand dunes and ripples are the basic forms. However, most current studies on the theoretic and numerical models of wind-blown sand movement only consider ideal conditions such as steady wind velocity, flat sand surface, etc. In fact, the windward slope gradient plays a great role in the lift-off and sand particle saltation. In this paper, we propose a numerical model for the coupling effect between wind flow and saltating sand particles to simulate wind-blown sand movement over the slope surface and use the SIMPLE algorithm to calculate wind flow and simulate sands transport by tracking sand particle trajectories. We furthermore compare the result of numerical simulation with wind tunnel experiments. These results prove that sand particles have obvious effect on wind flow, especially that over the leeward slope. This study is a preliminary study on windblown sand movement in a complex terrain, and is of significance in the control of dust storms and land desertification.

  7. Field Measurements of Influence of Sand Transport Rate on Structure of Wind-sand Flow over Coastal Transverse Ridge

    Institute of Scientific and Technical Information of China (English)

    DONG Yuxiang; S L NAMIKAS; P A HESP; MA Jun

    2008-01-01

    The structure of wind-sand flow under different total sand transport rates was measured with field vertical anemometer and sand trap on the crest of typical coastal transverse ridge in Changli Gold Coast of Hebei Province,which is one of the most typical coastal aeolian distribution regions in China and famous for the tall and typical coastal transverse ridges.The measurement results show that,on the conditions of approximate wind velocities and same surface materials and environments,some changes happen to the structure of wind-sand flow with the increase of total sand transport rate on the crest of coastal transverse ridge.First,the sand transport rates of layers at different heights in the wind-sand flow increase,with the maximum increase at the height layer of 4-8cm.Second,the ratios of sand transport rates of layers at different heights to total sand transport rate decrease at the low height layer (0-4cm),but increase at the high height layer (4-60cm).Third,the distribution of the sand transport rate in the wind-sand flow can be expressed by an exponential function at the height layer of 0-40cm,but it changes fi'om power function model to exponential function model in the whole height layer (0-60cm) and changes into polynomial function model at the height layer of 40-60cm with the increase of total sand transport rate.Those changes have a close relationship with the limit of sand grain size of wind flow transporting and composition of sand grain size in the wind-sand flow.

  8. Body Motion and Graphing.

    Science.gov (United States)

    Nemirovsky, Ricardo; Tierney, Cornelia; Wright, Tracy

    1998-01-01

    Analyzed two children's use of a computer-based motion detector to make sense of symbolic expressions (Cartesian graphs). Found three themes: (1) tool perspectives, efforts to understand graphical responses to body motion; (2) fusion, emergent ways of talking and behaving that merge symbols and referents; and (3) graphical spaces, when changing…

  9. Teaching Projectile Motion

    Science.gov (United States)

    Summers, M. K.

    1977-01-01

    Described is a novel approach to the teaching of projectile motion of sixth form level. Students are asked to use an analogue circuit to observe projectile motion and to graph the experimental results. Using knowledge of basic dynamics, students are asked to explain the shape of the curves theoretically. (Author/MA)

  10. 论沙粒两种起动关系与沙粒跃移的双重性%An Review of Relations of Two Starts and Duplicity of Saltation of Sand Particles

    Institute of Scientific and Technical Information of China (English)

    龚福华; 何兴东; 彭小玉; 郑力辉; 韩致文; 段争虎; 赵爱国

    2001-01-01

    The research of relations of two starts of sand particles is the continuation and development for understanding deeply the effects of two starts of sand particles.In this paper, the properties of two starts of sand particles were analyzed, the fluid start was defined as wind erosion start and impact start of saltation as substitution start for the first time. The fluid start was regarded as possessing initiative separability and impact start only possessing random separability. According to these properties, new definitions of two starting effects and successive motion of sand particles were put forward. The saltation of sand particles was regarded as possessing duplicity, saltation matters consumed much energy while impacting the ground surface, two starts of sand particles possessed inseparable relations that rose and declined together. Wind erosion was the results of complementation of superiority and mutual promotion of two starts of sand particles; however, accumulation on ground surface was sometimes the results of restricting each other of two starts because of energy consumption of saltation matters. By expounding and verifying in many ways,the ratio of two starting effects of sand particles was changed preliminarily into 4∶1 and even 3∶1 from traditional 19∶1.%研究沙粒两种起动关系是深入认识沙粒两种起动效能的继续和发展。文章分析了沙粒两种起动的不同性质,首次把流体起动界定为风蚀性起动,把跃移质冲击起动界定为置换性起动。认为流体起动具有主动分异性,而冲击起动只有随机分异性。根据这些特性对沙粒两种起动效能和沙粒连续移动提出了新义。认为沙粒跃移具有双重性,跃移质有其冲击地表的一面,也有其大量耗能的一面。沙粒两种起动具有兴衰与共的不可分割关系。地表风蚀是沙粒两种起动优势互补相互促进的结果;而地表堆积有时是跃移质耗能过多引起两种起

  11. Strength and sintering effects at ejection of explosively driven sand

    Science.gov (United States)

    Resnyansky, A. D.; Weckert, S. A.

    2014-05-01

    A description of the response of sand to extreme loads is very important for the evaluation of the sand ejecta impact effects on various targets. Sand is a complex material to simulate because of its porosity where the inter-phase equilibrium is hard to achieve under transient shock wave loading. A previously developed two-phase model with strength has been implemented in CTH and applied to sand. The shock response of the sand, including the Hugoniot abnormality known from the literature for highly porous silica, is adequately described with the material model. The sand unloading effects appearing as the ejecta are observed in the present work using dynamic flash X-ray of an aluminium target plate loaded by limestone sand ejecta from the detonation of a buried high explosive charge. The CTH modelling results compared with the flash X-ray images have demonstrated good agreement, particularly, in the description of momentum transfer to the target.

  12. A transport-rate model of wind-blown sand

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Sand transport by wind plays an important role in environmental problems.Formulating the sand-transport rate model has been of continuing significance,because the majority of the existing models relate sand-transport rate to the wind-shear velocity.However,the wind-shear velocity readapted to blown sand is difficult to determine from the measured wind profiles when sand movement occurs,especially at high wind velocity.Detailed wind tunnel tests were carried out to reformulate the sand-transport rate model,followed by attempts to relate sand-transport rate to parameters of wind velocity,threshold shear-velocity,and grain size.Finally,we validated the model based on the data from field observations.

  13. Pullout capacity of batter pile in sand.

    Science.gov (United States)

    Nazir, Ashraf; Nasr, Ahmed

    2013-03-01

    Many offshore structures are subjected to overturning moments due to wind load, wave pressure, and ship impacts. Also most of retaining walls are subjected to horizontal forces and bending moments, these forces are due to earth pressure. For foundations in such structures, usually a combination of vertical and batter piles is used. Little information is available in the literature about estimating the capacity of piles under uplift. In cases where these supporting piles are not vertical, the behavior under axial pullout is not well established. In order to delineate the significant variables affecting the ultimate uplift shaft resistance of batter pile in dry sand, a testing program comprising 62 pullout tests was conducted. The tests are conducted on model steel pile installed in loose, medium, and dense sand to an embedded depth ratio, L/d, vary from 7.5 to 30 and with various batter angles of 0°, 10°, 20°, and 30°. Results indicate that the pullout capacity of a batter pile constructed in dense and/or medium density sand increases with the increase of batter angle attains maximum value and then decreases, the maximum value of Pα occurs at batter angle approximately equal to 20°, and it is about 21-31% more than the vertical pile capacity, while the pullout capacity for batter pile that constructed in loose sand decreases with the increase of pile inclination. The results also indicated that the circular pile is more resistant to pullout forces than the square and rectangular pile shape. The rough model piles tested is experienced 18-75% increase in capacity compared with the smooth model piles. The suggested relations for the pullout capacity of batter pile regarding the vertical pile capacity are well predicted.

  14. Kirsten Sand. Arkitekt for sin tid

    Directory of Open Access Journals (Sweden)

    Elisabeth Seip

    2015-12-01

    Full Text Available Towards the end of World War II the retreating Germans burnt down nearly all buildings and other constructions in the counties of Finnmark and the northern parts of Troms in North Norway. The population evacuated but many returned as soon as possible, only to find themselves homeless. At this very demanding point Kirsten Sand decided to travel north, and do whatever she could as an architect to help. The pre-war housing situation was generally difficult. Low building standards and lack of money forced families in the cities to live under bad conditions. Kirsten Sand studied these conditions and took part in the efforts to better the situation. This knowledge provided a good starting point for the work she undertook after the war, in particular her profound understanding of the situation of women, their working conditions and positions in the household and society. Houses designed by Sand and her helpmates are simple but adequate, taking into account these women’s point of view. Ingebjørg Hage has thrown light on the work of Kirsten Sand in Finnmark and Troms in several ways. This article aims at describing Sand’s background as an architect before she left Oslo to travel north. It describes how housing and housing policy since long had been central to architects, especially so within the group she belonged to. In pre-war Oslo she had been engaged in planning and designing hospitals. During a period as inspector for the health authorities she learned a lot about the living conditions of people in general. After establishing her own architect’s office she mostly designed family houses, and during the war she engaged in research that further deepened her knowledge in the field. Thus she was particularly well equipped for the demanding tasks she undertook in the summer of 1945.

  15. Pullout capacity of batter pile in sand

    Directory of Open Access Journals (Sweden)

    Ashraf Nazir

    2013-03-01

    Full Text Available Many offshore structures are subjected to overturning moments due to wind load, wave pressure, and ship impacts. Also most of retaining walls are subjected to horizontal forces and bending moments, these forces are due to earth pressure. For foundations in such structures, usually a combination of vertical and batter piles is used. Little information is available in the literature about estimating the capacity of piles under uplift. In cases where these supporting piles are not vertical, the behavior under axial pullout is not well established. In order to delineate the significant variables affecting the ultimate uplift shaft resistance of batter pile in dry sand, a testing program comprising 62 pullout tests was conducted. The tests are conducted on model steel pile installed in loose, medium, and dense sand to an embedded depth ratio, L/d, vary from 7.5 to 30 and with various batter angles of 0°, 10°, 20°, and 30°. Results indicate that the pullout capacity of a batter pile constructed in dense and/or medium density sand increases with the increase of batter angle attains maximum value and then decreases, the maximum value of Pα occurs at batter angle approximately equal to 20°, and it is about 21–31% more than the vertical pile capacity, while the pullout capacity for batter pile that constructed in loose sand decreases with the increase of pile inclination. The results also indicated that the circular pile is more resistant to pullout forces than the square and rectangular pile shape. The rough model piles tested is experienced 18–75% increase in capacity compared with the smooth model piles. The suggested relations for the pullout capacity of batter pile regarding the vertical pile capacity are well predicted.

  16. Solvent extraction of Southern US tar sands

    Energy Technology Data Exchange (ETDEWEB)

    Penney, W.R.

    1990-01-01

    The Department of Chemical Engineering at the University of Arkansas, in association with Diversified Petroleum Recovery, Inc. (DPR) of Little Rock, Arkansas, has been developing a solvent extraction process for the recovery of bitumen from tar sands for the past five years. The unique feature of the process is that the bitumen is recovered from the solvent by contacting with a co-solvent, which causes the bitumen to precipitate. The overall purpose of this project is to study both the technical and economic feasibility of applying this technology for recovery of bitumen from tar sands by (1) investigating the socioeconmic factors which affect (a) plant siting and (b) the market value of recovered bitumen; (2) operating a process demonstration unit at the rate of 1 lb/hr recovered bitumen while producing clean sand and recyclable solvents; and (3) determine the economic conditions which will make a bitumen recovery project economical. DPR has analyzed the historical trends of domestic production, consumption, discoveries and reserves of crude oil. They have started an investigation of the volatility in the price of crude oil and of gasoline prices and of the differential between gasoline and crude oil. DPR continues to analyze the geographical movement and demand for asphalt products. Utah does not appear economically attractive as a site for a bitumen from tar sands asphalt plant. Oklahoma sites are now being studied. This report also contains the quarterly progress report from a University of Nevada study to determine bitumen composition, oxygen uptake rates, and viscosities of Alabama and Utah bitumens. Both reports have been indexed separately for inclusion on the data base.

  17. Solvent extraction of Southern US tar sands

    Energy Technology Data Exchange (ETDEWEB)

    Penney, W.R.

    1990-01-01

    The Department of Chemical Engineering at the University of Arkansas, in association with Diversified Petroleum Recovery, Inc. (DPR) of Little Rock, Arkansas, has been developing a solvent extraction process for the recovery of bitumen from tar sands for the past five years. The unique feature of the process is that the bitumen is recovered from the solvent by contacting with a co-solvent, which causes the bitumen to precipitate. The overall purpose of this project is to study both the technical and economic feasibility of applying this technology for recovery of bitumen from tar sands by (1) investigating the socioeconmic factors which affect (a) plant siting and (b) the market value of recovered bitumen; (2) operating a process demonstration unit at the rate of 1 lb/hr recovered bitumen while producing clean sand and recyclable solvents; and (3) determine the economic conditions which will make a bitumen recovery project economical. DPR has analyzed the historical trends of domestic production, consumption, discoveries and reserves of crude oil. They have started an investigation of the volatility in the price of crude oil and of gasoline prices and of the differential between gasoline and crude oil. DPR continues to analyze the geographical movement and demand for asphalt products. Utah does not appear economically attractive as a site for a bitumen from tar sands asphalt plant. Oklahoma sites are now being studied. This report also contains the quarterly progress report from a University of Nevada study to determine bitumen composition, oxygen uptake rates, and viscosities of Alabama and Utah bitumens. Both reports have been indexed separately for inclusion on the data base.

  18. Guide to preparing SAND reports. Revised

    Energy Technology Data Exchange (ETDEWEB)

    Locke, T.K. [ed.

    1996-04-01

    This guide contains basic information needed to produce a SAND report. Its guidelines reflect DOE regulation and Sandia policy. The guide includes basic writing instructions in an annotated sample report; guidance for organization, format, and layout of reports produced by line organizations; and information about conference papers, journal articles, and brochures. The appendixes contain sections on Sandia`s preferred usage, equations, references, copyrights and permissions, and publishing terms.

  19. Sorption of Arsenite onto Mackinawite Coated Sand

    Science.gov (United States)

    Gallegos, T. J.; Hayes, K. F.; Abriola, L. M.

    2004-05-01

    Arsenic contamination of groundwater is a widespread problem affecting aquifers in the United States as well as abroad. Recent strengthening of the US EPA MCL for arsenic has prompted the need for technology capable of removing both arsenite and arsenate from solution. Arsenite, the more toxic form of arsenic, is more difficult to remove from anoxic zones in the subsurface. Studies by others have demonstrated the affinity of some types of iron sulfides for arsenite, such as troilite, pyrite, amorphous iron sulfide and mackinawite. However, these studies have not provided a comprehensive investigation of the macroscopic behavior of arsenite in the presence of crystalline mackinawite in a form that can be readily applied to real-world treatment technologies. This study examines the behavior of arsenite in the presence of mackinawite coated sand. PH edge results demonstrate that arsenite sorption onto mackinawite coated sand increases with increasing pH, reaching maximum removal at pH 10. Arsenite removal, albeit slight, occurring below pH 5 is independent of pH indicative of a different removal mechanism. Isotherm studies show that at low concentrations, removal is Langmuirian in nature. Arsenite sorption abruptly converts to linear behavior at high concentrations, possibly attributed to the saturation of the monolayer. Ionic strength effects were assessed by comparing pH edge data developed for three different concentrations of NaCl background electrolyte solution. Increases in ionic strength enhance the removal of arsenite from solution, suggesting possible inner-sphere surface complexation removal mechanisms. Information gathered in this study can be used to further develop surface complexation models to describe and predict reactivity of arsenite in the presence of mackinawite coated sands in anoxic regions. Mackinawite coated sands investigated here may provide a feasible reactive medium for implementation in above-ground sorption reactors or subsurface

  20. PHYSICAL MODELING OF ODOMETRIC COMPRESSION OF SAND

    Directory of Open Access Journals (Sweden)

    Lyashenko P. A.

    2016-10-01

    Full Text Available The odometric compression of sand with constant rate of loading (CRL or constant rate of deformation (CRD and continuous registration of the corresponding reaction allows to identify the effect of stepwise changes of deformation (at the CRL and the power reaction (at the CRD. Physical modeling of compression on the sandy model showed the same effect. The physical model was made of fine sand with marks, mimicking large inclusions. Compression of the soil at the CRD was uneven, stepwise, and the strain rate of the upper boundary of the sandy model changed cyclically. Maximum amplitudes of cycles passed through a maximum. Inside of the sand model, the uneven strain resulted in the mutual displacement of the adjacent parts located at the same depth. The growth of external pressure, the marks showed an increase or decrease in displacement and even move opposite to the direction of movement (settlement the upper boundary of the model ‒ "floating" of marks. Marks, at different depths, got at the same time different movements, including mutually contradictory. The mark settlements sudden growth when the sufficiently large pressure. These increments in settlements remained until the end of loading decreasing with depth. They were a confirmation of the hypothesis about the total destruction of the soil sample at a pressure of "structural strength". The hypothesis of the "floating" reason based on the obvious assumption that the marks are moved together with the surrounding sand. The explanation of the effect of "floating" is supported by the fact that the value of "floating" the more, the greater the depth

  1. Sand Ripple Dynamics on the Inner Shelf

    Science.gov (United States)

    2006-01-01

    Sand Ripple Dynamics on the Inner Shelf Donald N. Slinn Department of Civil and Coastal Engineering, University of Florida Gainesville, FL 32611...Florida,Department of Civil and Coastal Engineering,Gainesville,FL,32611-6590 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY...2002. 452: p. 1-24. Acrivos, A., Shear-Induced Particle Diffusion in Concentrated Suspensions of Noncolloidal Particles. Journal of Rheology , 1995

  2. Drawing a Line in the Sand

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    An Inner Mongolian woman takes on the desert and converts extensive arid regions into arable land by Ni Yanshuo CONVERTING vast tracks of desert into arable land is no easy task, even using the most advanced technology.Yet a woman who hails from north China’s Inner Mongolia Autonomous Region met this challenge head on.Using the helping hands of other determined women,she has made remarkable progress in pushing back the sands of time.

  3. Waste foundry sand: Environmental implication and characterization

    Directory of Open Access Journals (Sweden)

    Gabriela Penkaitis

    2012-12-01

    Full Text Available This paper presents the results of analyses using Scanning Electron Microscopy in field samples of waste foundry sand, as well as the results of granulometric, chemical and groundwater analyses. Field data allowed to characterize waste foundry sand and showed that there are elevated concentrations of metals in the groundwater (iron, manganese, boron and selenium, in addition to other potentially toxic elements (chromium, copper, cobalt, nickel, zinc, aluminum, iron, manganese, which are present in the waste and are considered not hazardous by current standards. Even if these elements are not considered hazardous, their concentrations above the permissible limit compromise the environmental quality of the site, posing risks to the local population, since they work in agriculture and use groundwater. Two different types of waste foundry sands were identified using granulometric analyses. Electron microscopy showed features related to morphological, chemical and mineralogical characteristics of grains that make up the waste. Quartz was the dominant mineral. Waste foundry sand is composed of two types of grains: a rounded grain with almost no incrustations formed during alloy production, and a second type of grain, which is not rounded, has incrustations, and always has several metals derived from alloys and associated with these incrustations. Chemical elements detected in groundwater with concentrations above the limits established by the regulatory bodies were found in wells located in the landfill area. Most of these elements show higher concentrations downstream, some of them with concentrations above the regulatory limit, and others show an increase in concentration upstream, indicating that the landfill may be impacting the local environment.

  4. American Las Vegas Sands Corp. Visiting Beijing

    Institute of Scientific and Technical Information of China (English)

    Li Yinghong; Liu Jinliang

    2006-01-01

    @@ On August 29, Wan Jifei, Chairman of CCPIT, meets the visiting delegation led by Sheldon G. Adelson,Chairman of the Board and principal owner of Las Vegas Sands Corp. in CCPIT. Zhao Zhenge, Vice Director of International Connection Department of CCPIT, Luo Guoxiong from Beijing China Exhibition Investment Company, Xu Jingyi, Assistant Director of American and Oceanian Affairs Division of CCPIT, also attended the meeting.

  5. Ground resistance influences lizard burial in dry and wet sand

    Science.gov (United States)

    Sharpe, Sarah; Kuckuk, Robyn; Goldman, Daniel

    2012-11-01

    Many terrestrial animals move within soil in which water content can vary, and little is known about how water content affects locomotor performance. To investigate the effect of water content on burial, we created controlled dry and wet substrates. We used 0.3 mm glass particles and varied water content W, the mass of water to mass of dry loosely packed sand. Drag force on a submerged 1.6 cm diameter rod increased by a factor of 4 as W increased from 0 to 0.03, after which force increases were small. Drag force in wet media periodically fluctuated with time and corresponded with surface fracturing. We characterized how W affected burial performance and strategy of a generalist burrower, the ocellated skink lizard (Chalcides ocellatus). High speed x-ray imaging was used to measure head, body and limb kinematics in substrates with W= 0 and W= 0.03. In both states during burial the body was maintained in a curved posture and the animal moved using a start-stop motion. During movement, the head oscillated and the forelimb on the convex side of the body was used to push the animal forward. Both speed and angular excursion of the head oscillation decreased in the W= 0.03 state. The differences in locomotion were attributed to the changing resistance force within the media.

  6. Oil sands mining water use and management

    Energy Technology Data Exchange (ETDEWEB)

    Bender, M.; Long, D.; Fitch, M. [Golder Associates Ltd., Calgary, AB (Canada)

    2010-07-01

    There are currently 4 bitumen mining operations operating along the Athabasca River in northern Alberta. This paper presented details of the water licences, historical water use, present water use, and future plans for water management in relation to oil sands mining operations. The study was based on work currently conducted for the Oil Sands Developers Group (OSDG) and Canadian Association of Petroleum Producers (CAPP), as well as on mine site water balance analyses for proposed mines in the region. Typical mine site water balances were discussed, and water use rates for the mining operations were reviewed. The new Athabasca River water management framework may require that mines provide additional water storage or delayed reclamation of mine areas in order to offset water losses during winter low-flow periods. New regulations may also reduce the requirement for make-up water. The study also noted that release criteria are still being developed for on-site water within closed-loop mine operations. The oil sands industry will need to balance various factors related to water use in the future. 5 refs., 3 figs.

  7. Collaborative production management for oil sands operations

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Andrew [Matrikon (Canada)

    2011-07-01

    This paper gives an overview of the collaborative production management of oil sands operations. Some characteristics of oil sands operations include oil treatment, hydro treating, diluent addition, logistics, and environmental impact assessments. Some of the business challenges include regulatory uncertainty, a fluid workforce and a technology still in the process of being developed. Improvement is only possible when process is assessed and measured; hence, production data management is very important. Production data measurements encompass such areas as planning, documentation and transactions. Regulatory data reporting is represented using a flow chart. The concepts of business application architecture and functional reference modeling are also explained. Benchmarking plays a vital role, some aspects of which would be technology, automation and integration. Certain advantages of timely assessment are increased production, equity, and goodwill as well as reduction in costs, risk, and capital requirements. The relevance and importance of collaboration, awareness of web technology and aggregate information are also explained. From the study, it can be concluded that the key to overall improvement in the oil sands industry will be improved production management.

  8. Recycled sand in lime-based mortars.

    Science.gov (United States)

    Stefanidou, M; Anastasiou, E; Georgiadis Filikas, K

    2014-12-01

    The increasing awareness of the society about safe guarding heritage buildings and at the same time protecting the environment promotes strategies of combining principles of restoration with environmentally friendly materials and techniques. Along these lines, an experimental program was carried out in order to investigate the possibility of producing repair, lime-based mortars used in historic buildings incorporating secondary materials. The alternative material tested was recycled fine aggregates originating from mixed construction and demolition waste. Extensive tests on the raw materials have been performed and mortar mixtures were produced using different binding systems with natural, standard and recycled sand in order to compare their mechanical, physical and microstructure properties. The study reveals the improved behavior of lime mortars, even at early ages, due to the reaction of lime with the Al and Si constituents of the fine recycled sand. The role of the recycled sand was more beneficial in lime mortars rather than the lime-pozzolan or lime-pozzolan-cement mortars as a decrease in their performance was recorded in the latter cases due to the mortars' structure.

  9. Permeability Tests on Silkeborg Sand No. 0000

    DEFF Research Database (Denmark)

    Lund, Willy; Jakobsen, Kim Parsberg

    The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends on the charact......The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends...... on the characteristics of the soil matrix, the permeability is determined for different void ratios. All tests are performed on reconstituted specimens of Silkeborg Sand No. 0000. The permeability is determined by use of a falling head apparatus. The apparatus, test procedures and the analysis method are described...... in the succeeding sections. Finally the test results are briefly summarised and a relationship between void ratio l and permeability is established....

  10. The bituminous sands : a Canadian mirage?

    Energy Technology Data Exchange (ETDEWEB)

    Rousse, D.R. [Quebec Univ., Chicoutimi, PQ (Canada). Dept. des Sciences Appliquees; Nasr, G.J. [Lebanese Univ., Roumieh (Lebanon). Faculty of Engineering; Turcotte, S.F. [Quebec Univ., Montreal, PQ (Canada). Centre d' Etudes Internationales et Mondialisation; Salah, N.B. [Ecole Superieure des Sciences et Techniques De Tunis, Tunis (Tunisia). LMMP

    2009-07-01

    This paper examined the controversy about the potential role of a significant increase in Canadian oil sands production in order to bridge the upcoming gap between the world's increasing energy demand and the total recoverable oil supply. The paper presented the actual potential of different scenarios and considered the prediction cost forecasts. A brief overview of environmental impacts and the real return on investments were also provided. Environmental impacts that were considered included land degradation; water contamination; ecosystem damage; and air pollution. Nuclear energy was also presented as a possible solution. The paper demonstrated that even in a very optimistic scenario, Canada's oil sands accelerated production has a negligible effect on the aforementioned gap, has a considerable impact on environment that has yet to be accounted for. Energy ratios that were presented included energy return on energy investment; energy available on energy used; and energy payback. It was concluded that enhanced recovery techniques are clearly needed for future sustainable exploitation of these bituminous sands. 32 refs., 1 fig.

  11. Summertime View of North Polar Sand Dunes

    Science.gov (United States)

    2006-01-01

    10 October 2006 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a suite of dunes in one of the several north polar dune fields. The bright surfaces adjacent to some of the dunes are patches of frost. These dunes spend much of the autumn, winter, and spring seasons covered with carbon dioxide frost. Only in late spring and in summer are the dark windblown sands fully exposed. Over the course of the 9+ years of the MGS mission, the MOC team has sought evidence that sand dunes may be migrating downwind over time. However, no clear examples of the movement of a whole dune have been identified. On Earth, such movement is typically detectable in air photos of the smallest active dunes over periods of a few years. Owing to the fact that the north polar dunes spend much of each martian year under a cover of frost, perhaps these move much more slowly than their frost-free, terrestrial counterparts. The sand may also be somewhat cemented by ice or minerals, likewise preventing vigorous dune migration in the present environment. This view covers an area approximately 3 km (1.9 mi) wide and is illuminated by sunlight from the lower left. The dunes are located near 79.8oN, 127.1oW, and the picture was acquired on 11 September 2006.

  12. The sedimentary structure of linear sand dunes

    Science.gov (United States)

    Bristow; Bailey; Lancaster

    2000-07-06

    Linear sand dunes--dunes that extend parallel to each other rather than in star-like or crescentic forms--are the most abundant type of desert sand dune. But because their development and their internal structure are poorly understood, they are rarely recognized in the rock record. Models of linear dune development have not been able to take into account the sub-surface structure of existing dunes, but have relied instead either on the extrapolation of short-term measurements of winds and sediment transport or on observations of near-surface internal sedimentary structures. From such studies, it has not been clear if linear dunes can migrate laterally. Here we present images produced by ground penetrating radar showing the three-dimensional sedimentary structure of a linear dune in the Namib sand sea, where some of the world's largest linear dunes are situated. These profiles show clear evidence for lateral migration in a linear dune. Moreover, the migration of a sinuous crest-line along the dune produces divergent sets of cross-stratification, which can become stacked as the dune height increases, and large linear dunes can support superimposed dunes that produce stacked sets of trough cross-stratification. These clear structural signatures of linear dunes should facilitate their recognition in geological records.

  13. Motion control systems

    CERN Document Server

    Sabanovic, Asif

    2011-01-01

    "Presents a unified approach to the fundamental issues in motion control, starting from the basics and moving through single degree of freedom and multi-degree of freedom systems In Motion Control Systems, Šabanovic and Ohnishi present a unified approach to very diverse issues covered in motion control systems, offering know-how accumulated through work on very diverse problems into a comprehensive, integrated approach suitable for application in high demanding high-tech products. It covers material from single degree of freedom systems to complex multi-body non-redundant and redundant systems. The discussion of the main subject is based on original research results and will give treatment of the issues in motion control in the framework of the acceleration control method with disturbance rejection technique. This allows consistent unification of different issues in motion control ranging from simple trajectory tracking to topics related to haptics and bilateral control without and with delay in the measure...

  14. Stochastic ground motion simulation

    Science.gov (United States)

    Rezaeian, Sanaz; Xiaodan, Sun; Beer, Michael; Kougioumtzoglou, Ioannis A.; Patelli, Edoardo; Siu-Kui Au, Ivan

    2014-01-01

    Strong earthquake ground motion records are fundamental in engineering applications. Ground motion time series are used in response-history dynamic analysis of structural or geotechnical systems. In such analysis, the validity of predicted responses depends on the validity of the input excitations. Ground motion records are also used to develop ground motion prediction equations(GMPEs) for intensity measures such as spectral accelerations that are used in response-spectrum dynamic analysis. Despite the thousands of available strong ground motion records, there remains a shortage of records for large-magnitude earthquakes at short distances or in specific regions, as well as records that sample specific combinations of source, path, and site characteristics.

  15. Shaly sand formation evaluation in tight gas sands using electrochemical potential measurements

    Science.gov (United States)

    Sharma, M. M.; Jin, M.

    1991-08-01

    Equations are developed that directly relate the shaly conductivity to the electrochemical (membrane) potential (EP). The model is applied to both fully and partially saturated sands. The relationship between the resistivity index and the water saturation is also expressed in terms of a single membrane potential measurement. The Ep measured at different salinities are compared with model prediction using a single membrane potential measurement. Sigma (sub 0) versus Sigma (sub w) curves are then generated using the model equations and compared with measured curves. Experimental results are presented for electrochemical potential measurement made in the lab on 50 tight gs sand samples. It is shown that the measurements can be correlated with CEC although the CEC measured by grinding up the samples was always higher than that estimated from Ep measurements. The Ep measurements are combined with the equations for partial saturation developed in the report to obtain water saturations in a tight gas sand well. Through the example it is shown that it is possible to determine the water saturation in Shaly sands from one membrane potential measurement at a known salinity together with a set of resistivity logs. The results clearly demonstrate the applicability of the method as a practical procedure for Shaly sand information evaluation.

  16. Patch behaviour and predictability properties of modelled finite-amplitude sand ridges on the inner shelf

    Directory of Open Access Journals (Sweden)

    N. C. Vis-Star

    2008-12-01

    Full Text Available The long-term evolution of shoreface-connected sand ridges is investigated with a nonlinear spectral model which governs the dynamics of waves, currents, sediment transport and the bed level on the inner shelf. Wave variables are calculated with a shoaling-refraction model instead of using a parameterisation. The spectral model describes the time evolution of amplitudes of known eigenmodes of the linearised system. Bottom pattern formation occurs if the transverse bottom slope of the inner shelf, β, exceeds a critical value βc. For fixed model parameters the sensitivity of the properties of modelled sand ridges to changes in the number (N−1 of resolved subharmonics (of the initially fastest growing mode is investigated. For any N the model shows the growth and subsequent saturation of the height of the sand ridges. The saturation time scale is several thousands of years, which suggests that observed sand ridges have not reached their saturated stage yet. The migration speed of the ridges and the average longshore spacing between successive crests in the saturated state differ from those in the initial state. Analysis of the potential energy balance of the ridges reveals that bed slope-induced sediment transport is crucial for the saturation process. In the transient stage the shoreface-connected ridges occur in patches. The overall characteristics of the bedforms (saturation time, final maximum height, average longshore spacing, migration speed hardly vary with N. However, individual time series of modal amplitudes and bottom patterns strongly depend on N, thereby implying that the detailed evolution of sand ridges can only be predicted over a limited time interval. Additional experiments show that the critical bed slope βc increases with larger offshore angles of wave incidence, larger offshore wave heights and longer wave periods, and that the corresponding maximum height of the ridges

  17. Male Spine Motion During Coitus

    Science.gov (United States)

    Sidorkewicz, Natalie

    2014-01-01

    Study Design. Repeated measures design. Objective. To describe male spine movement and posture characteristics during coitus and compare these characteristics across 5 common coital positions. Summary of Background Data. Exacerbation of pain during coitus due to coital movements and positions is a prevalent issue reported by low back pain patients. A biomechanical analysis of spine movements and postures during coitus has never been conducted. Methods. Ten healthy males and females engaged in coitus in the following preselected positions and variations: QUADRUPED, MISSIONARY, and SIDELYING. An optoelectronic motion capture system was used to measure 3-dimensional lumbar spine angles that were normalized to upright standing. To determine whether each coital position had distinct spine kinematic profiles, separate univariate general linear models, followed by Tukey's honestly significant difference post hoc analysis were used. The presentation of coital positions was randomized. Results. Both variations of QUADRUPED, mQUAD1 and mQUAD2, were found to have a significantly higher cycle speed than mSIDE (P = 0.043 and P = 0.034, respectively), mMISS1 (P = 0.003 and P = 0.002, respectively), and mMISS2 (P = 0.001 and P spine movement varied depending on the coital position; however, across all positions, the majority of the range of motion used was in flexion. Based on range of motion, the least-to-most recommended positions for a male flexion-intolerant patient are mSIDE, mMISS2, mQUAD2, mMISS1, and mQUAD1. Conclusion. Initial recommendations—which include specific coital positions to avoid, movement strategies, and role of the partner—were developed for male patients whose low back pain is exacerbated by specific motions and postures. Level of Evidence: N/A PMID:25208042

  18. Numerical Analysis of Flow Erosion on Sand Discharge Pipe in Nitrogen Drilling

    Directory of Open Access Journals (Sweden)

    Hongjun Zhu

    2013-01-01

    Full Text Available In nitrogen drilling, entrained sand particles in the gas flow may cause erosive wear on metal surfaces and have a significant effect on the operational life of discharge pipelines, especially for elbows. In this paper, computational fluid dynamics (CFD simulations based code FLUENT is carried out to investigate the flow erosion on a sand discharge pipe in conjunction with an erosion model. The motion of the continuum phase is captured based on solving the three-dimensional Reynolds-averaged Navier-Stokes (RANS equations, while the kinematics and trajectory of the sand particles are evaluated by the discrete phase model (DPM. The flow field has been examined in terms of pressure, velocity, and erosion rate profiles along the flow path in the bend of the simulated discharge pipe. Effects of flow parameters such as inlet velocity, sandy volume fraction, and particle diameter and structure parameters such as pipe diameter and bend curvature are analyzed based on a series of numerical simulations. The results show that small pipe diameter or small bend curvature leads to serious erosion, while slow flow, little sandy volume fraction, and small particle diameter can weaken erosion. The results obtained from the present work provide useful guidance to practical operation and discharge pipe design.

  19. The formation and migration of sand ripples in closed conduits: experiments with turbulent water flows

    CERN Document Server

    Florez, Jorge Eduar Cardona

    2016-01-01

    The transport of solid particles by a fluid flow is frequently found in nature and industry. Some examples are the transport of sand in rivers and hydrocarbon pipelines. When the shear stresses exerted by a fluid flow on a granular bed remain moderate, some grains are set in motion without fluidizing the bed; the moving grains form a layer, known as bed load, that moves while maintaining contact with the fixed part of the bed. Under bed load conditions, the granular bed may become unstable, generating ripples and dunes. Sand ripples are commonly observed in closed conduits and pipes such as in petroleum pipelines, sewer systems, and dredging lines. Although of importance for many scientific domains and industrial applications, the formation of ripples in closed conduits is not well understood, and the problem is still open. This paper presents an experimental study on the formation and migration of sand ripples under a turbulent closed-conduit flow and bed-load conditions. In our experiments, fully-developed ...

  20. Pollutant advective spreading in beach sand exposed to high-energy tides

    Science.gov (United States)

    Itugha, Okuroghoboye D.; Chen, Daoyi; Guo, Yakun

    2016-11-01

    This paper presents field measurements in which dye solute was injected into coastal sand to investigate contaminant advection in intertidal beach sand. The measurements show the pathways of a contaminated plume in the unsaturated zone during both the flood and ebb tides. A prescribed amount of dye tracer solution was directly injected through the topsoil, with average porosity 0.3521 ± 0.01, at predetermined locations of the River Mersey's outer estuarial beach during ebb-tide. The injected dye was monitored, sampled and photographed over several tidal cycles. The distinctive features of the plume (full two dimensional cross-sections), sediments and water-table depth were sampled in-situ, close to the injection point (differing from previous contaminant monitoring tests in aquifers). The advective movement is attributed to tidal impact which is different from contaminant transport in aquifers. The experimental results show that plumes have significantly large spatial variability, diverging upwards and converging downwards, with a conical geometric shape which is different from the usual spherical/elliptical shape reported in literature. The mean vertical motion of the plume reaches three times the top-width within ten tidal cycles, exceeding the narrow bottom-width by a factor of order 2. The observed transport features of the plume within the beach sand have significant relevance to saltwater intrusion, surface water and groundwater quality. The field observations are unique and can serve as a valuable benchmark database for relevant numerical studies.

  1. Scalable motion vector coding

    Science.gov (United States)

    Barbarien, Joeri; Munteanu, Adrian; Verdicchio, Fabio; Andreopoulos, Yiannis; Cornelis, Jan P.; Schelkens, Peter

    2004-11-01

    Modern video coding applications require transmission of video data over variable-bandwidth channels to a variety of terminals with different screen resolutions and available computational power. Scalable video coding is needed to optimally support these applications. Recently proposed wavelet-based video codecs employing spatial domain motion compensated temporal filtering (SDMCTF) provide quality, resolution and frame-rate scalability while delivering compression performance comparable to that of the state-of-the-art non-scalable H.264-codec. These codecs require scalable coding of the motion vectors in order to support a large range of bit-rates with optimal compression efficiency. Scalable motion vector coding algorithms based on the integer wavelet transform followed by embedded coding of the wavelet coefficients were recently proposed. In this paper, a new and fundamentally different scalable motion vector codec (MVC) using median-based motion vector prediction is proposed. Extensive experimental results demonstrate that the proposed MVC systematically outperforms the wavelet-based state-of-the-art solutions. To be able to take advantage of the proposed scalable MVC, a rate allocation mechanism capable of optimally dividing the available rate among texture and motion information is required. Two rate allocation strategies are proposed and compared. The proposed MVC and rate allocation schemes are incorporated into an SDMCTF-based video codec and the benefits of scalable motion vector coding are experimentally demonstrated.

  2. STUDY ON HOT SAND COOLING EQUIPMENT WITH DAMPING SAND CASCADE AND VERTICAL SPOUTED-FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    L.C. Wang; F. Wang; X.H. You

    2005-01-01

    A new kind of hot sand cooling equipment with vertical spouted-fluidized bed is developed in this paper. It is similar to the traditional horizontal vibrating fluidized boiling cooler in principle but different from it in structure. The processing principle of the cooler is analyzed. The influence of main structural and processing parameters on the cooling effect and its mechanism are researched. Other characteristics of the cooler are discussed also. Experiment results show that the cooling efficiency η is equal to or larger than 83%, the temperature of output sand is less than 40℃ with the temperature of input sand is about between 80 and 90℃, and the productivity is 5t/(h·m)

  3. Small Strain Behaviour and Viscous Effects on Sands and Sand-Clay Mixtures

    Science.gov (United States)

    Di Benedetto, H.

    This lecture paper focuses on sands and sand-clay mixtures behaviour in the small strain domain. Non viscous and viscous components are measured, identified and modelled within the framework of a 3 component model. Two precision prototype devices (triaxial and hollow cylinder) both equipped with piezoelectric sensors are used. Non viscous measured behaviour considering small quasi-static cycles and wave properties are compared with simulations obtained from 2 recently formulated anisotropic hypoelastic models (DBGS and DBGSP). Then, viscous experimental part is compared with the proposed model prediction. This model is an asymptotic expression, for the small strain domain, of a viscous evanescent formalism proposed by the author. It takes into account very peculiar behaviour observed on sands. Simulation for loadings with and without rotation of axes and for different rate histories, are quite satisfactory.

  4. Dynamics of sand ridges in coastal seas: the effect of storms, tides and grain sorting

    Science.gov (United States)

    Walgreen, M.

    2003-10-01

    observed phase shift between bed topography and mean grain size for shoreface-connected ridges (finest sand on seaward flanks) is due to the selective transport via suspended load of grains with different sizes. Parameter values are based on the sand ridges along the Atlantic coast of North America. A net stabilising effect on the initial growth and an enhanced migration is predicted. A physical explanation for the model results is given. During fair weather or tidally dominated conditions, when bed load transport of sediment is dominant, the results indicate an increase in initial growth and migration rates of tidal sand ridges for a bimodal sediment mixture. A symmetrical tidal current results in a grain size distribution, with the coarsest sand found at the crest of the ridges. Results are compared with the tidal ridges on the Belgian coastal shelf. The investigation of the long-term evolution of shoreface-connected ridges focuses on storm-dominated micro-tidal shelves. It is shown that, starting from an initial state without bedforms, a pattern of ridges with a finite height develops. The evolution of the spatial patterns in the mean grain size and bottom topography are shown and discussed in terms of physical mechanisms.

  5. A Continuum Description of Vibrated Sand

    CERN Document Server

    Eggers, J; Eggers, Jens; Riecke, Hermann

    1999-01-01

    The motion of a thin layer of granular material on a plate undergoing sinusoidal vibrations is considered. We develop equations of motion for the local thickness and the horizontal velocity of the layer, where the driving comes from the violent impact of the grains on the surface. A linear stability theory reveals a novel mechanism for the excitation of waves. Comparing both the stability diagram and the dispersion relation with experiment, we are able to check the consistency of our model.

  6. Sand box experiments with bioclogging of porous media: hydraulic conductivity reductions.

    Science.gov (United States)

    Seifert, Dorte; Engesgaard, Peter

    2012-08-01

    Tracer experiments during clogging and de-clogging experiments in a 2D sand box were via an image analysis used to establish a data set on the relation between changes in hydraulic conductivity (K) and relative porosity (β). Clogging appears to create a finger-like tracer transport, which could be caused by an initial heterogeneous distribution of biomass in the sand box. De-clogging occurs at a slower rate possibly due to the presence of inert biomass that is not affected by the starvation conditions by sudden removal of the substrate source. The tracer front was observed to get disturbed closer and closer to the substrate source during the experiments suggesting that the zone of clogging moved upstream. Three clogging models, K(β), from the literature were tested for their ability to describe the temporal changes in clogging at the scale of the sand box; the model of Clement et al. (1996) that makes no assumption on biomass distribution, the plug formation model of Thullner et al. (2002a), and the biofilm-plug formation model of Vandevivere (1995). The plug formation and biofilm-plug formation models both match the observed changes between the hydraulic conductivity of the sand box and the relative porosity. Unfortunately our experiments did not reach low relative porosities where the two models predict different behaviors. The model by Clement et al. (1996) underestimates clogging.

  7. Luminescence dating of aeolian sands from archaeological sites in Northern Britain: a preliminary study

    Science.gov (United States)

    Sommerville, A. A.; Sanderson, D. C. W.; Hansom, J. D.; Housley, R. A.

    2001-12-01

    Luminescence dating of aeolian sands from archaeological sites has potential to contribute to regional chronologies for sediment deposition and to provide a greater understanding of climatic influences on early communities. The Northern and Western Isles of Scotland provide important opportunities for sampling archaeologically intercalated sands for these purposes, and to provide constrained samples for method validation. A wide range of modern beaches have been sampled in the Western and Orkney Isles of Scotland to examine regional variations in luminescence sensitivity, residuals and ease of bleaching. These modern sands have negligible residuals for infra-red stimulated luminescence (IRSL), small optically stimulated luminescence (OSL) residuals and significant thermoluminescence residuals. The relationship between these signals and laboratory bleaching results may indicate the initial depositional environment, and hence lead to a means of identifying well-bleached dating samples. Both sensitivities and residuals show regional differences, reflecting local geology. Preliminary ages obtained from aeolian sands associated with archaeological sites at Amble (Northumbria) and Tofts Ness (Sanday, Orkney) using regenerative blue OSL techniques on extracted quartz are broadly consistent with external age controls from the first and third millennium BC.

  8. A new sand adsorbent for the removal and reuse of nickel ions from aqueous solutions.

    Science.gov (United States)

    Tao, Wenhong; Qi, Ling; Duan, Huimin; Liu, Shiquan

    2017-04-01

    Nickel ions (Ni(II)) in aqueous solutions were removed by a sand adsorbent with a surface functionalized porous coating. The sand adsorbent has a very large surface area of 150 m(2)/g. The influence of pH, initial concentration of the solution, temperature, contact time and adsorbent dosage on the removal efficiency of the synthesized sand adsorbent toward Ni(II) in the aqueous solutions were studied. The results indicate that the adsorption of nickel onto the sand adsorbent greatly increases the pH range of 2-4 and slightly increases with temperature from 25 to 40 °C. The maximum removal efficiency and ion retention in per unit mass of the adsorbent were 100% and 5.78 mg/g, respectively, under the specified experimental conditions. The adsorption can be described by the pseudo-second-order kinetic model and the Freundlich adsorption model. The adsorbed nickel (4.24 mg/g) together with the spent adsorbent were successfully employed to prepare a brown glass, suggesting a new way to reutilize the recovered nickel from wastewater and to avoid secondary pollution caused by the used adsorbents.

  9. Pore space analysis of NAPL distribution in sand-clay media

    Science.gov (United States)

    Matmon, D.; Hayden, N.J.

    2003-01-01

    This paper introduces a conceptual model of clays and non-aqueous phase liquids (NAPLs) at the pore scale that has been developed from a mathematical unit cell model, and direct micromodel observation and measurement of clay-containing porous media. The mathematical model uses a unit cell concept with uniform spherical grains for simulating the sand in the sand-clay matrix (???10% clay). Micromodels made with glass slides and including different clay-containing porous media were used to investigate the two clays (kaolinite and montmorillonite) and NAPL distribution within the pore space. The results were used to understand the distribution of NAPL advancing into initially saturated sand and sand-clay media, and provided a detailed analysis of the pore-scale geometry, pore size distribution, NAPL entry pressures, and the effect of clay on this geometry. Interesting NAPL saturation profiles were observed as a result of the complexity of the pore space geometry with the different packing angles and the presence of clays. The unit cell approach has applications for enhancing the mechanistic understanding and conceptualization, both visually and mathematically, of pore-scale processes such as NAPL and clay distribution. ?? 2003 Elsevier Science Ltd. All rights reserved.

  10. Policy Analysis of the Canadian Oil Sands Experience

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2013-09-01

    For those who support U.S. oil sands development, the Canadian oil sands industry is often identified as a model the U.S. might emulate, yielding financial and energy security benefits. For opponents of domestic oil sands development, the Canadian oil sands experience illustrates the risks that opponents of development believe should deter domestic policymakers from incenting U.S. oil sands development. This report does not seek to evaluate the particular underpinnings of either side of this policy argument, but rather attempts to delve into the question of whether the Canadian experience has relevance as a foundational model for U.S. oil sands development. More specifically, this report seeks to assess whether and how the Canadian oil sands experience might be predictive or instructive in the context of fashioning a framework for a U.S. oil sands industry. In evaluating the implications of these underpinnings for a prospective U.S. oil sands industry, this report concentrates on prospective development of the oil sands deposits found in Utah.

  11. Cytotoxicity of yellow sand in lung epithelial cells

    Indian Academy of Sciences (India)

    Y H Kim; K S Kim; N J Kwak; K H Lee; S A Kweon; Y Lim

    2003-02-01

    The present study was carried out to observe the cytotoxicity of yellow sand in comparison with silica and titanium dioxide in a rat alveolar type II cell line (RLE-6TN). Yellow sand (China Loess) was obtained from the loess layer in the Gunsu Province of China. The mean particle diameter of yellow sand was about 0.003 ± 0.001 mm. Major elements of yellow sand were Si(27.7 ± 0.6%), Al(6.01 ± 0.17%), and Ca(5.83 ± 0.23%) in that order. Silica and yellow sand significantly decreased cell viability and increased [Ca2+]i. All three particles increased the generation of H2O2. TiO2 did not change Fenton activity, while silica induced a slight increase of Fenton activity. In contrast, yellow sand induced a significant increase of Fenton activity. Silica, yellow sand and TiO2 induced significant nitrite formations in RLE-6TN cells. Silica showed the highest increase in nitrite formation, while yellow sand induced the least formation of nitrite. Silica and yellow sand increased the release of TNF-. Based on these results, we suggest that yellow sand can induce cytotoxicity in RLE-6TN cells and reactive oxygen species, Fenton activity and reactive nitrogen species might be involved in this toxicity.

  12. Solidification and stabilization of cadmium ions in sand-cement-clay mixture.

    Science.gov (United States)

    Shawabkeh, Reyad A

    2005-10-17

    This study was carried out to test the ability of a mixture of sand, cement and clay for immobilizing cadmium ions from leaching out into water resources. Various samples with different mass ratios for this mixture were tested to determine their efficiency for adsorbing cadmium. The compressive test, cation exchange capacity (CEC), adsorption equilibrium and leaching test were applied to each sample. The sample that showed the highest cation exchange capacity with 53.1 meq/100 g and compressive strength with 11.05 N/mm2 consists of 25% sand, 50% cement and 25% clay. The equilibrium data for Cd2+ removal using this sample showed a multilayer adsorption, which could be fitted using Brunauer-Emmett-Teller adsorption isotherm model with a regression coefficient of 0.999. The maximum cadmium uptake obtained from this model was 82.618 mg/g solid. The mobility of Cd2+ in acidic solution drawn-off after 18 h of initial mixing was 66.06 mg when the solid sample initially contains 6.0 g Cd2+. This value decreased to 14.33 mg when only 1.0 g Cd2+ was initially spiked in the sample. Introducing clay into this sample enhanced its sorption capacity while the presence of sand and cement enhanced its compressive strength.

  13. Microbial pesticide removal in rapid sand filters for drinking water treatment – Potential and kinetics

    DEFF Research Database (Denmark)

    Hedegaard, Mathilde Jørgensen; Albrechtsen, Hans-Jørgen

    2014-01-01

    or metabolites mecoprop (MCPP), bentazone, glyphosate and p-nitrophenol were applied in initial concentrations of 0.03–2.4 μg/L. In all the investigated waterworks the concentration of pesticides in the water decreased – MCPP decreased to 42–85%, bentazone to 15–35%, glyphosate to 7–14% and p-nitrophenol 1......–3% – from the initial concentration over a period of 6–13 days. Mineralisation of three out of four investigated pesticides was observed at Sjælsø waterworks Plant II – up to 43% of the initial glyphosate was mineralised within six days. At Sjælsø waterworks Plant II the removal kinetics of bentazone......Filter sand samples, taken from aerobic rapid sand filters used for treating groundwater at three Danish waterworks, were investigated for their pesticide removal potential and to assess the kinetics of the removal process. Microcosms were set up with filter sand, treated water, and the pesticides...

  14. A shoreline sand wave formation event at Dungeness, UK.

    Science.gov (United States)

    Falqués, A.; Arriaga, J.; Francesca, R.; Eddie, C.

    2016-12-01

    Alongshore rhythmic morphological patterns at different length scales are quite common along sandy beaches. Well known examples are megacusps and crescentic bars/rip channel systems with alongshore wavelengths ˜ 100-1000 m. At larger scales (˜ 1-10 km or more) there are the km-scale shoreline sand waves. During the last two decades there has been much research to unravel the origin of such intriguing patterns and to get insight into their dynamics. The hypothesis that they emerge out of positive feedbacks between hydrodynamics and morphology has been amply confirmed by mathematical modelling. In particular, the potential role of high-angle waves (large incidence angles with respect to shore) in driving km-scale shoreline sand waves has been investigated (Ashton et al., 2001, van den Berg et al., 2012). However, direct tests with nature are very difficult and are inexistent to our knowledge. This is so because these tests would require detailed measurements of the bathymetry and the wave conditions at the moment of their formation from a featureless morphology. Dungeness beach is located at the English shore of the Dover straight facing northeast part of a cuspate foreland. It is a gravel beach (D50=6-10 mm) quite steep until 1 m depth (β≈0.13) and gentle until 3 m depth (β≈0.005) without shore-parallel bars. Bathymetric maps of this beach are available since 2007 and the wave conditions are also known from a wave buoy in 43 m depth. The shorelines from 2007 until 2013 show some subtle and evolving undulations. But remarkably, in 2014 a series of two undulations develop with a wavelength of about 0.5 km. They persist until 2016 and migrate to the N. This is a clear formation event that provides a unique opportunity to compare observations with the outputs of morphodynamic models for the initial formation of such features. Therefore, the objectives are: 1) Characterize the bathymetric evolution and the wave conditions prior/during the formation event, 2) run

  15. HYDRAULIC ELEVATOR INSTALLATION ESTIMATION FOR THE WATER SOURCE WELL SAND-PACK CLEANING UP

    Directory of Open Access Journals (Sweden)

    V. V. Ivashechkin

    2016-01-01

    Full Text Available The article offers design of a hydraulic elevator installation for cleaning up water-source wells of sand packs. It considerers the installation hydraulic circuit according to which the normal pump feeds the high-level tank water into the borehole through two parallel water lines. The water-jet line with washing nozzle for destroying the sand-pack and the supply pipe-line coupled with the operational nozzle of the hydraulic elevator containing the inlet and the supply pipelines for respectively intaking the hydromixture and removing it from the well. The paper adduces equations for fluid motion in the supply and the water-jet pipelines and offers expressions for evaluating the required heads in them. For determining water flow in the supply and the water-jet pipe lines the author proposes to employ graphical approach allowing finding the regime point in Q–H chart by means of building characteristics of the pump and the pipe-lines. For calculating the useful vertical head, supply and dimensions of the hydraulic elevator the article employs the equation of motion quantity with consistency admission of the motion quantity before and after mixing the flows in the hydraulic elevator. The suggested correlations for evaluating the hydraulic elevator efficiency determine the sand pack removal duration as function of its sizes and the ejected fluid flow rate. A hydraulic-elevator installation parameters estimation example illustrates removing a sand pack from a water-source borehole of 41 m deep and 150 mm diameter bored in the village of Uzla of Myadelsk region, of Minsk oblast. The working efficiency of a manufactured and laboratory tested engineering prototype of the hydraulic elevator installation was acknowledged in actual tests at the indicated borehole site. With application of graphical approach, the suggested for the hydraulic elevator installation parameters calculation procedure allows selecting, with given depth and the borehole diameter

  16. Motion of a Vortex Filament in the Half Space

    CERN Document Server

    Aiki, Masashi

    2010-01-01

    A model equation for the motion of a vortex filament immersed in three dimensional, incompressible and inviscid fluid is investigated as a humble attempt to model the motion of a tornado. We solve an initial-boundary value problem in the half space where we impose a boundary condition in which the vortex filament is allowed to move on the boundary.

  17. ToF camera ego-motion estimation

    CSIR Research Space (South Africa)

    Ratshidaho, T

    2012-10-01

    Full Text Available We present three approaches for ego-motion estimation using Time-of-Flight (ToF) camera data. Ego-motion is defined as a process of estimating a camera’s pose (position and orientation) relative to some initial pose using the camera’s image...

  18. A laboratory experiment on the evolution of a sand gravel reach under a lack of sediment supply

    NARCIS (Netherlands)

    Orru, C.; Chavarrias Borras, V.; Ferrara, V.; Stecca, G.; Blom, A.

    2015-01-01

    A flume experiment was conducted to examine the evolution of a sand-gravel reach under a lack of sediment supply. A bed composed of a bimodal sediment mixture was installed with a uniform slope and an gradual fining pattern. At the upstream end of the flume the initial bed consisted of 100% gravel,

  19. Projectile Motion Details.

    Science.gov (United States)

    Schnick, Jeffrey W.

    1994-01-01

    Presents an exercise that attempts to correct for the common discrepancies between theoretical and experimental predictions concerning projectile motion using a spring-loaded projectile ball launcher. Includes common correction factors for student use. (MVL)

  20. Projectile Motion with Mathematica.

    Science.gov (United States)

    de Alwis, Tilak

    2000-01-01

    Describes how to use the computer algebra system (CAS) Mathematica to analyze projectile motion with and without air resistance. These experiments result in several conjectures leading to theorems. (Contains 17 references.) (Author/ASK)

  1. A Projectile Motion Bullseye.

    Science.gov (United States)

    Lamb, William G.

    1985-01-01

    Explains a projectile motion experiment involving a bow and arrow. Procedures to measure "muzzle" velocity, bow elastic potential energy, range, flight time, wind resistance, and masses are considered. (DH)

  2. Mathisson's helical motions demystified

    CERN Document Server

    Costa, L Filipe O; Zilhão, Miguel

    2012-01-01

    The motion of spinning test particles in general relativity is described by Mathisson-Papapetrou-Dixon equations, which are undetermined up to a spin supplementary condition, the latter being today still an open question. The Mathisson-Pirani (MP) condition is known to lead to rather mysterious helical motions which have been deemed unphysical, and for this reason discarded. We show that these assessments are unfounded and originate from a subtle (but crucial) misconception. We discuss the kinematical explanation of the helical motions, and dynamically interpret them through the concept of hidden momentum, which has an electromagnetic analogue. We also show that, contrary to previous claims, the frequency of the helical motions coincides exactly with the zitterbewegung frequency of the Dirac equation for the electron.

  3. Travelers' Health: Motion Sickness

    Science.gov (United States)

    ... Disease Directory Resources Resources for Travelers Adventure Travel Animal Safety Blood Clots Bug Bites Business Travel Cold ... motion sickness. Adding distractions—controlling breathing, listening to music, or using aromatherapy scents such as mint or ...

  4. Toying with Motion.

    Science.gov (United States)

    Galus, Pamela J.

    2002-01-01

    Presents a variety of activities that support the development of an understanding of Newton's laws of motion. Activities use toy cars, mobile roads, and a seat-of-nails. Includes a scoring rubric. (DDR)

  5. Vision and Motion Pictures.

    Science.gov (United States)

    Grambo, Gregory

    1998-01-01

    Presents activities on persistence of vision that involve students in a hands-on approach to the study of early methods of creating motion pictures. Students construct flip books, a Zoetrope, and an early movie machine. (DDR)

  6. Developmental Reorganisation of Visual Motion Pathways

    Directory of Open Access Journals (Sweden)

    John Wattam-Bell

    2012-05-01

    Full Text Available In adults, visual form and motion activate independent networks of extrastriate areas which are roughly aligned with the ventral and dorsal streams, respectively. Using high-density steady-state ERPs, we have previously shown that the scalp topographies of infant form and motion responses are markedly different from those in adults, implying a substantial developmental reorganisation of the underlying cortical pathways. However, it is hard to discern the nature of this reorganisation from the ambiguous polarity and timing information available in steady-state ERPs. We have started to address this problem by measuring transient ERPs to motion onset. In adults, the transient ERP topography initially suggests activation of extrastriate cortex, but rapidly switches to a dominant focus over the occipital pole originating in V1 and/or V2. The infant ERP is similar to the initial phase of adult ERP, but lacks the sudden switch to a V1/V2-dominated topography. The implications of these results for the reorganisation of cortical motion pathways will be discussed, with particular focus on the idea that the adult V1/V2 component is mainly driven by feedback from extrastriate motion areas (eg, V5, and that these feedback signals are not present in the infant brain.

  7. Influence of silicate on the transport of bacteria in quartz sand and iron mineral-coated sand.

    Science.gov (United States)

    Dong, Zhe; Yang, Haiyan; Wu, Dan; Ni, Jinren; Kim, Hyunjung; Tong, Meiping

    2014-11-01

    The influence of silicate on the transport and deposition of bacteria (Escherichia coli) in packed porous media were examined at a constant 20 mM ionic strength with different silicate concentrations (from 0 to 1 mM) at pH 7. Transport experiments were performed in two types of representative porous media, both bare quartz sand and iron mineral-coated quartz sand. In bare quartz sand, the breakthrough plateaus in the presence of silicate in suspensions were lower and the corresponding retained profiles were higher than those without silicate ions, indicating that the presence of silicate in suspensions decreased cell transport in bare quartz sand. Moreover, the decrease of bacteria transport in quartz sand induced by silicate was more pronounced with increasing silicate concentrations from 0 to 1 mM. However, when EPS was removed from cell surfaces, the presence of silicate in cell suspensions (with different concentrations) did not affect the transport behavior of bacteria in quartz sand. The interaction of silicate with EPS on cell surfaces negatively decreased the zeta potentials of bacteria, resulting in the decreased cell transport in bare quartz sand when silicate was copresent in bacteria suspensions. In contrast, the presence of silicate in suspensions increased cell transport in iron mineral-coated sand. Silicate ions competed with bacteria for the adsorption sites on mineral-coated sand, contributing to the increased cell transport in mineral-coated sand with silicate present in cell suspensions.

  8. Coupled transverse motion

    Energy Technology Data Exchange (ETDEWEB)

    Teng, L.C.

    1989-01-01

    The magnetic field in an accelerator or a storage ring is usually so designed that the horizontal (x) and the vertical (y) motions of an ion are uncoupled. However, because of imperfections in construction and alignment, some small coupling is unavoidable. In this lecture, we discuss in a general way what is known about the behaviors of coupled motions in two degrees-of-freedom. 11 refs., 6 figs.

  9. Western Gas Sands Project status report

    Energy Technology Data Exchange (ETDEWEB)

    Atkinson, C.H.

    1978-09-30

    The status of government sponsored projects undertaken to increase gas production from low-permeability gas sands of the western United States during August 1978 is summarized. Background information is given in the September 1977 Status Report, NVO/0655-100. One of the largest massive Hydraulic Fracture (MHF) treatment to date was performed on Gas Producing Enterprises Well No. CIGE 2-29. C.H. Atkinson, Western Gas Sands Project (WGSP) Manager and D.C. Bleakly, CER Corporation were observers. Oriented coring operations on the Mitchell Energy well, Muse-Duke No. 1 were observed by Atkinson and Bleakly near Mexia, Texas. The Fourth Annual Department of Energy Symposium on Enhanced Oil and Gas Recovery and Improved Drilling Methods was held on August 29-31, 1978 in Tulsa, Oklahoma. The USGS continued geological and geophysical studies in the four primary study areas. Low-level oblique photography of Tertiary and Cretaceous rocks exposed in the Rock Springs Uplift area was completed, and core from the J.C. Paine well in Montana was sampled for petrograhic analysis. Bartlesville Energy Technology Center continued work on the improved pressure coring system and anticipates completion of the project by September 30, 1978. Preliminary work began on the Parametric Analysis of MHF Test Data, an Engineering Study of Western Gas Sands, by Intercomp. The National Laboratories, funded by DOE are continuing their work in the area of research and development. The emphasis is on instrumentation systems, rock mechanics, mathematical modeling, and data analysis. The Mitchell Energy well, Muse Duke No. 1, has reached total depth and was logged on August 31, 1978. The DOE well test facility was moved from the RB-MHF 3 well in Colorado to Vernal, Utah for trailer modifications and checkout.

  10. Pressure and Motion of Dry Sand -- Translation of Hagen's Paper from 1852

    CERN Document Server

    Tighe, B P; Sperl, Matthias; Tighe, Brian P.

    2006-01-01

    In a remarkable paper from 1852, Gotthilf Heinrich Ludwig Hagen measured and explained two fundamental aspects of granular matter: The first effect is the saturation of pressure with depth in a static granular system confined by silo walls -- generally known as the Janssen effect. The second part of his paper describes the dynamics observed during the flow out of the container -- today often called the Beverloo law -- and forms the foundation of the hourglass theory. The following is a translation of the original German paper from 1852.

  11. Perpetual Motion Machine

    Directory of Open Access Journals (Sweden)

    D. Tsaousis

    2008-01-01

    Full Text Available Ever since the first century A.D. there have been relative descriptions of known devices as well as manufactures for the creation of perpetual motion machines. Although physics has led, with two thermodynamic laws, to the opinion that a perpetual motion machine is impossible to be manufactured, inventors of every age and educational level appear to claim that they have invented something «entirely new» or they have improved somebody else’s invention, which «will function henceforth perpetually»! However the fact of the failure in manufacturing a perpetual motion machine till now, it does not mean that countless historical elements for these fictional machines become indifferent. The discussion on every version of a perpetual motion machine on the one hand gives the chance to comprehend the inventor’s of each period level of knowledge and his way of thinking, and on the other hand, to locate the points where this «perpetual motion machine» clashes with the laws of nature and that’s why it is impossible to have been manufactured or have functioned. The presentation of a new «perpetual motion machine» has excited our interest to locate its weak points. According to the designer of it the machine functions with the work produced by the buoyant force

  12. TECHNIQUES ABOUT DIRECT OPTIMIZING CONTROL OF GREEN SAND QUALITY*

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Green sand casting is still a main method in the world at present and it is very significant to develop the technology of controlling green sand quality. A new concept, from contents test to contents control, is advanced. In order to realize the new idea, a new method to on-line test active clay and moisture of green sand - double powers energizing alternately (DPEA) method is put forwards. The principle of the new method is to energize standard sand sample with AC and DC powers and to test the electric parameters, and then, to calculate active clay and moisture of green sand by using artificial neural network (ANN). Based on this new method, a direct optimizing system for controlling green sand quality is developed. Techniques about testing and controlling methods, hardware and software are discussed.

  13. Thermo-Insulating Moulding Sand for thin Walled Castings

    Directory of Open Access Journals (Sweden)

    Cholewa M.

    2014-10-01

    Full Text Available In paper the selection of the composition and determination of main properties of novel moulding sand was described. The mail goal was to create moulding sand characterized by high thermal insulating properties in relations with low specific weight. This type of moulding sand will find application in thin walled castings with complex geometry, in particular for cores of the skeleton castings. In this work the results of the compressive strength, permeability and friability was presented. It was noted that aluminosilicate microspheres are suitable as moulding sand matrix. Influence of the polyglicol addition on quality and properties of the moulding sand was described. The use of the aluminosilicate microspheres allowed to obtain the moulding sand characterized by high insulation rate, low specific weight and good mechanical properties.

  14. Optimising the composition of natural moulding sands including thermal aspects

    Directory of Open Access Journals (Sweden)

    Jerzy St. Kowalski

    2011-04-01

    Full Text Available The paper discusses the problem of the choice of the moulding sand mixture composition in terms of the sand behaviour in contact withmolten metal. Studies of high-temperature phenomena make assessment of the sand composition applicability under real operatingconditions possible, thus leading to the elimination of sand-originating casting defects. The research was conducted on selected moulding materials included in the composition of traditional moulding sand mixtures without the addition of carbon. The effect of moulding sand composition and moisture content on the linear dilatation and stress-induced allotropic changes of quartz was examined. The analysis of these phenomena was based on 3D charts and maps generated from data collected during the tests.

  15. Removal of heavy metals through adsorption using sand

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The removal of four heavy metals i.e. Pb, Cr, Cu, and Zn from their aqueous solutions, using ordinary sand as an adsorbent, was studied at 20oC. The amount of metal adsorbed to form monolayer on sand(am), obtained from Langmuir isotherm, exhibited the preference of metals for sand in the order Pb>Cr>Cu>Zn. The heavy metal-sand adsorption phenomena can be illustrated on the basis of the interaction between surface functional group of silicates (sand) and the metal ions. It is deduced that sand can be used as a low cost adsorbent for the removal of heavy metal from wastewater (containing low conc. of metals), especially in the developing countries.

  16. Numerical study on deformation and failure of reinforced sand

    Institute of Scientific and Technical Information of China (English)

    PENG Fang-le; LI Jian-zhong; Tatsuoka Fumio

    2005-01-01

    In order to investigate the deformation and failure of reinforced sand, and the reinforcing mechanism of flexible and rigid reinforcement, a set of plane strain compression tests of dense Toyoura reinforced sand with planar reinforcement of a wide range of stiffness were analysed by a nonlinear finite element method. The analysis was incorporated into an energy-based elasto-plastic constitutive model for sand to develop a stress path-independent work-hardening parameter based on the modified plastic strain energy concept. Numerical results indicate that the global stress-strain relations of sand specimens are reinforced by using relatively flexible and rigid reinforcement, and an unreinforced sand specimen can be reasonably simulated by the current finite element method. It is also found that the reinforcing mechanism and progressive failure with a development of shear bands in reinforced sand can be reasonably examined by the finite element method.

  17. 'Sharks Teeth' -- Sand Dunes in Proctor Crater

    Science.gov (United States)

    2001-01-01

    Sometimes, pictures received from Mars Global Surveyor's Mars Orbiter Camera (MOC) are 'just plain pretty.' This image, taken in early September 2000, shows a group of sand dunes at the edge of a much larger field of dark-toned dunes in Proctor Crater. Located at 47.9oS, 330.4oW, in the 170 km (106 mile) diameter crater named for 19th Century British astronomer Richard A. Proctor (1837-1888), the dunes shown here are created by winds blowing largely from the east/northeast. A plethora of smaller, brighter ripples covers the substrate between the dunes. Sunlight illuminates them from the upper left.

  18. Sphere impact and penetration into wet sand

    Science.gov (United States)

    Marston, J. O.; Vakarelski, I. U.; Thoroddsen, S. T.

    2012-08-01

    We present experimental results for the penetration of a solid sphere when released onto wet sand. We show, by measuring the final penetration depth, that the cohesion induced by the water can result in either a deeper or shallower penetration for a given release height compared to dry granular material. Thus the presence of water can either lubricate or stiffen the granular material. By assuming the shear rate is proportional to the impact velocity and using the depth-averaged stopping force in calculating the shear stress, we derive effective viscosities for the wet granular materials.

  19. Heating tar sands formations to visbreaking temperatures

    Science.gov (United States)

    Karanikas, John Michael; Colmenares, Tulio Rafael; Zhang, Etuan; Marino, Marian; Roes, Augustinus Wilhelmus Maria; Ryan, Robert Charles; Beer, Gary Lee; Dombrowski, Robert James; Jaiswal, Namit

    2009-12-22

    Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat may be controlled so that at least a majority of the section reaches an average temperature of between 200.degree. C. and 240.degree. C., which results in visbreaking of at least some hydrocarbons in the section. At least some visbroken hydrocarbon fluids may be produced from the formation.

  20. Biogenic crust dynamics on sand dunes

    CERN Document Server

    Kinast, Shai; Yizhaq, Hezi; Ashkenazy, Yosef

    2012-01-01

    Sand dunes are often covered by vegetation and biogenic crusts. Despite their significant role in dune stabilization, biogenic crusts have rarely been considered in studies of dune dynamics. Using a simple model, we study the existence and stability ranges of different dune-cover states along gradients of rainfall and wind power. Two ranges of alternative stable states are identified: fixed crusted dunes and fixed vegetated dunes at low wind power, and fixed vegetated dunes and active dunes at high wind power. These results suggest a cross-over between two different forms of desertification.

  1. Geology of the Athabasca oil sands

    Science.gov (United States)

    Mossop, G. D.

    1980-01-01

    In-place bitumen resources in the Alberta oil sands are estimated at 1350 billion barrels. Open-pit mining and hot water extraction methods, which involve the handling of huge tonnages of earth materials, are being employed in the two commercial plants now operating. In situ recovery methods will be required to tap the 90 percent of reserves that are too deeply buried to be surface mined. Development of in situ technologies will be painstaking and expensive, and success will hinge on their compatibility with extremely complex geological conditions in the subsurface.

  2. Sphere impact and penetration into wet sand

    KAUST Repository

    Marston, J. O.

    2012-08-07

    We present experimental results for the penetration of a solid sphere when released onto wet sand. We show, by measuring the final penetration depth, that the cohesion induced by the water can result in either a deeper or shallower penetration for a given release height compared to dry granular material. Thus the presence of water can either lubricate or stiffen the granular material. By assuming the shear rate is proportional to the impact velocity and using the depth-averaged stopping force in calculating the shear stress, we derive effective viscosities for the wet granular materials.

  3. A model of neural mechanisms in monocular transparent motion perception.

    Science.gov (United States)

    Raudies, Florian; Neumann, Heiko

    2010-01-01

    Transparent motion is perceived when multiple motions are presented in the same part of visual space that move in different directions or with different speeds. Several psychophysical as well as physiological experiments have studied the conditions under which motion transparency occurs. Few computational mechanisms have been proposed that allow to segregate multiple motions. We present a novel neural model which investigates the necessary mechanisms underlying initial motion detection, the required representations for velocity coding, and the integration and segregation of motion stimuli to account for the perception of transparent motion. The model extends a previously developed architecture for neural computations along the dorsal pathway, particularly, in cortical areas V1, MT, and MSTd. It emphasizes the role of feedforward cascade processing and feedback from higher to earlier processing stages for selective feature enhancement and tuning. Our results demonstrate that the model reproduces several key psychophysical findings in perceptual motion transparency using random dot stimuli. Moreover, the model is able to process transparent motion as well as opaque surface motion in real-world sequences of 3-d scenes. As a main thesis, we argue that the perception of transparent motion relies on the representation of multiple velocities at one spatial location; however, this feature is necessary but not sufficient to perceive transparency. It is suggested that the activations simultaneously representing multiple activities are subsequently integrated by separate mechanisms leading to the segregation of different overlapping segments.

  4. Preliminary Observations from the 2014 Sand Dunes Experiment

    Science.gov (United States)

    2014-10-01

    2014 Sand Dunes Experiment by Christopher W. Miller, Ching-Sang Chiu, D. Benjamin Reeder, Ying-Jang Yang, Linus Chiu, and Chi-Fang Chen...COVERED (From-To) June 2014 4. TITLE AND SUBTITLE Preliminary Observations from the 2014 Sand Dunes Experiment 5a. CONTRACT NUMBER 5b. GRANT NUMBER...position of the Department of Defense or the U.S. Government 14. ABSTRACT The Sand Dunes 2014 experiment was international US – Taiwan

  5. MC-Parameter Calibration of Baskarp Sand No. 15

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Hanson, Mats; Hjort, T.;

    The soil parameters are dependent on both confining pressure and density index. The density index of Baskarp Sand can be determined by conducting cone penetration tests with the mini-CPT cone used in the Geotechnical Engineering Laboratory at Aalborg University. The unit weight of Baskarp Sand No...... several conventional drained triaxial tests at two different density indices performed on Baskarp Sand No. 15 (Ibsen & Bødker, 1994). The used triaxial tests are listed in Table 1 and Table 2....

  6. A soil emergence trap for collections of phlebotomine sand flies

    Directory of Open Access Journals (Sweden)

    Casanova Cláudio

    2001-01-01

    Full Text Available The identification of breeding sites of sand flies is of great epidemiological interest. A soil emergence trap for investigating potential sand fly breeding sites is described. The trap was tested in two rural areas in the Mogi Guaçu River Valley where the American cutaneous leishmaniasis is an endemic disease. Seventy-three sand fly individuals of three species, Lutzomyia intermedia s. l., L. whitmani and L. pessoai, were collected on the forest floor and peridomicile.

  7. Possibilities of preparation asphalt concrete by oil sands of Kazakhstan

    OpenAIRE

    Erbol Tileuberdi; Yerdos Ongarbayev; F. Behrendt; Schneider, I.; Yerzhan Imanbayev; B. Tuleutayev; Yerlan Doszhanov; Zulkhair Mansurov

    2012-01-01

    In the paper physicochemical properties of oil sands of Munayli-Mola deposits and efficient ways to use them for preparing asphalt concrete were represented. For determination of organic part of oil sands the extraction methods were used in Soxhlet apparatus by variety of solvents. It has been established 16 wt.% content of natural bitumen in oil sands, which compared with results of ash content determination. According to results of experiment, the natural bitumen is heavy oil and its charac...

  8. Microwave processing of oil sands and contribution of clay minerals

    OpenAIRE

    John P. Robinson; Binner, Eleanor; Saeid, Abdul; Al-Harahsheh, Mohammad; Kingman, S. W.

    2014-01-01

    This study establishes the feasibility of microwave heating for extracting oil from Oil Sands in ex-situ processes. Previous studies in this area have shown some potential, but have not characterised the dielectric properties of the Oil Sands used, nor related them to the mineral composition, both of which are vital if successful scale up is to be achieved. In this work the fundamental interactions of microwave energy with Oil Sands are investigated and understood for the first time, and the ...

  9. Seed Mucilage Improves Seedling Emergence of a Sand Desert Shrub

    OpenAIRE

    Xuejun Yang; Baskin, Carol C.; Baskin, Jerry M.; Guangzheng Liu; Zhenying Huang

    2012-01-01

    The success of seedling establishment of desert plants is determined by seedling emergence response to an unpredictable precipitation regime. Sand burial is a crucial and frequent environmental stress that impacts seedling establishment on sand dunes. However, little is known about the ecological role of seed mucilage in seedling emergence in arid sandy environments. We hypothesized that seed mucilage enhances seedling emergence in a low precipitation regime and under conditions of sand buria...

  10. Provenance of coastal dune sands along Red Sea, Egypt

    Indian Academy of Sciences (India)

    Samir M Zaid

    2017-06-01

    Texture, mineralogy, and major and trace element geochemistry of 26 coastal dune sand samples were studied to determine the provenance and tectonic environment of two dune fields close to the beaches of Safaga (SF) and Quseir (QS) at the Egyptian Red Sea coast. Onshore winds generate fine, moderate, moderately-well to well-sorted, coarse-skewed to near-symmetrical dune sands with mesokurtic distributions. Winds pick up and transport grains from nearby beach sands and alluvial deposits into a wide Red Sea coastal plain at the border of the beach. The mineralogical (Qt–Ft–Lt) and geochemical composition of the sands, indicate that SF and QS coastal dune sands are mature and influenced by quartz-rich sands. The average CIA values in SF and QS coastal dune sands are low relative to the range of the PAAS, suggesting an arid climate and a low intensity of chemical weathering. The SF and QS coastal dune sand samples are plotted in the recycled orogen and partly in craton interior fields suggesting recycled older sedimentary and partly metamorphic-plutonic sources. The high content of quartz with shell debris and carbonates in coastal dune sands support the recycled sedimentary beach and alluvial sand sources. The dominance of heavy minerals like amphiboles (hornblende) and biotite in the coastal dune sands also supports the effect of metamorphic-plutonic source rocks. The new tectonic discriminant-function diagrams suggest that the coastal dune sands were deposited in a passive margin of a synrift basin. The results provide a good evidence for the extension in the Red Sea rift system during Oligocene-post Pliocene, which is consistent with the general geology of Egypt.

  11. EXPERIMENTAL STUDY AND NUMERICAL SIMULATION OF FLUORIDE IN SAND

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hong-mei; SU Bao-yu

    2006-01-01

    The transport and transformation of fluoride in sand were studied by using soil tank test under the condition of saturated water in this article. Based on the analysis of the laboratory experiments, the rules of fluorine transportation and transformation were simulated in sand by solving the advection-diffusion equation. Through comparison between computed results and observed data , it is shown that the established model and determined parameters could be used to simulate the fluoride transport in sand.

  12. Oil sands to the rescue: oil sand microbial communities can degrade recalcitrant alkyl phenyl alkanoic acids

    Energy Technology Data Exchange (ETDEWEB)

    Whitby, Corinne [University of Essex (Canada)], email: cwhitby@essex.ac.uk

    2011-07-01

    Almost half of all global oil reserves are found as biodegraded heavy oils found in vast tar sand deposits located in North and South America and these account for 47% of Canadian oil production. Oil sand extraction generates large amounts of toxic waste water, known as oil sand process waters (OSPW), that are stored in large tailing ponds that contain toxic compounds like naphthenic acids (NAs). The presence of NAs creates problems like toxicity, corrosion, and the formation of calcium napthenate deposits which block pipelines and other infrastructure and need to be removed. This paper presents oil sand microbial communities that can degrade these NAs. The approach is to apply new aliphatic and aromatic NAs as substrates to supplement and identify NA degrading microbes and also to identify the metabolites produced and explain NA degradation pathways and the functional genes involved. The chemistry and the processes involved are explained. From the results, it is suggested that pure cultures of P. putida KT2440 be used against NAs.

  13. Modeling the response of shoreface-connected sand ridges to sand extraction on an inner shelf

    NARCIS (Netherlands)

    Nnafie, A.; de Swart, Huib; Calvete, D.; Garnier, R.

    2014-01-01

    Shoreface-connected sand ridges are rhythmic bedforms that occur on many storm-dominated inner shelves. The ridges span several kilometers, are a few meters high, and they evolve on a timescale of centuries. A processbased model is used to gain a fundamental insight into the response of these ridges

  14. Modeling the response of shoreface-connected sand ridges to sand extraction on an inner shelf

    NARCIS (Netherlands)

    Nnafie, A.; de Swart, Huib; Calvete, D.; Garnier, R.

    2014-01-01

    Shoreface-connected sand ridges are rhythmic bedforms that occur on many storm-dominated inner shelves. The ridges span several kilometers, are a few meters high, and they evolve on a timescale of centuries. A processbased model is used to gain a fundamental insight into the response of these ridges

  15. Chemical Stablilisation of Sand : Part VIII Furan Resins as Dune and Coastal Sand Stabiliser

    Directory of Open Access Journals (Sweden)

    Ram Gopal

    1990-04-01

    Full Text Available Studies on furan resin as dune sand stabiliser are presented. Influence of acid catalysts, viz. phenol disulphonic acid, sulphuric acid, hydrochloric acid and phosphoric acid and other catalysts, viz. trichlorotoluene and benzoyl chloride along with promoters, zinc chloride and ferric chloride, on the strength of stabilised furan resin-sand specimens has been discussed. Optimisation studies on resin content, catalysts and promoters and curing conditions have revealed that maximum strength of 260 kg/cm/sup 2/ of the standard specimens made by compaction of coastal sand using furan resins (10 per cent, sulphuric acid (9N, 30 per cent and a curing time of 2 hr at 40 degree Centigrade is higher than the 170 kg/cm/sup 2/ of specimens made of Rajasthan desert sand. Sandy patches stabilised by seepage technique recorded a maximum strength of 125 kg/cm/sup 2/. Physico-chemical characteristics of this system and effect of environment on stabilised specimens have also been studied and field trials conducted successfully. This resin-catalyst system would be extremely useful in humid and saline field (coastal areas for different military applications.

  16. Motion contrast using optical coherence tomography

    Science.gov (United States)

    Fingler, Jeffrey Paul

    Diagnosis of ophthalmic diseases like age-related macular degeneration is very important for treatment of the disease as well as the development of future treatments. Optical coherence tomography (OCT) is an optical interference technique which can measure the three-dimensional structural information of the reflecting layers within a sample. In retinal imaging, OCT is used as the primary diagnostic tool for structural abnormalities such as retinal holes and detachments. The contrast within the images of this technique is based upon reflectivity changes from different regions of the retina. This thesis demonstrates the developments of methods used to produce additional contrast to the structural OCT images based on the tiny fluctuations of motion experienced by the mobile scatterers within a sample. Motion contrast was observed for motions smaller than 50 nm in images of a variety of samples. Initial contrast method demonstrations used Brownian motion differences to separate regions of a mobile Intralipid solution from a static agarose gel, chosen in concentration to minimize reflectivity contrast. Zebrafish embryos in the range of 3-4 days post fertilization were imaged using several motion contrast methods to determine the capabilities of identifying regions of vascular flow. Vasculature identification was demonstrated in zebrafish for blood vessels of all orientations as small as 10 microns in diameter. Mouse retinal imaging utilized the same motion contrast methods to determine the contrast capabilities for motions associated with vasculature within the retina. Improved contrast imaging techniques demonstrated comparable images to fluorescein angiography, the gold standard of retinal vascular imaging. Future studies can improve the demonstrated contrast analysis techniques and apply them towards human retinal motion contrast imaging for ophthalmic diagnostic purposes.

  17. Severe sand aspiration: a case report with complete recovery.

    Science.gov (United States)

    Glinjongol, Chanin; Kiatchaipipat, Surachai; Thepcharoenniran, Somchai

    2004-07-01

    A 5-year-old boy, previously healthy, was admitted to Ratchaburi Hospital after being buried in a sand pile. He presented with dyspnea and tachypnea. Chest radiograph showed opaque particles in both main and segmental bronchi (sand bronchogram). The first attempt of bronchoscopy was unsatisfactory as a considerable amount of sand particles had migrated further into the distal bronchi. A second bronchoscopy was performed with 0.9% saline lavage. Most of the sand particles were successfully removed. Intravenous steroids and antibiotics were administered for treatment. The patient was discharged uneventfully by the end of the first week of hospitalization.

  18. Olivine sand from Kawashiri Beach in Kagoshima, Japan

    OpenAIRE

    MATSUI, Tomoaki; マツイ, トモアキ; 松井, 智彰

    2001-01-01

    The olivine sand from Kawashiri Beach was studied by chemical and X-ray analyses. At least six groups of olivine are mixed in the olivine sand in this region, and they are classified according to the composition of the silicate-melt inclusions in them. The composition of the olivine sand ranges from Fo_70 to Fo_75, and the sum of the Mn_2SiO_4 and Ca_2SiO_4 content is less than 1 (mol %). These crystal chemical data for the olivine sand not only provide basic mineralogical info...

  19. [Influence of perlite sand on the skin in experiment].

    Science.gov (United States)

    Dracheva, E E; Iatsyna, I V; Lapina, N E; Ianin, V A; Antoshina, L I; Zhadan, I Iu; Krasavina, E K

    2012-01-01

    In the present work influence of perlite sand has been studied on a skin of Sprague-Dawley male rat (300-350 g). The biopsy of intact rat skin has been used as control. Contact of the perlite sand with animals' skin causes the reaction of an inflammation amplifying with increase of duration of the influence of substance. Therefore, despite an inert chemical compound, long contact with perlite sand in conditions of production can promote development of skin diseases. From the result of this investigation it is concluded that perlite sand causes irritating action on the skin and it is necessary to apply additional protective means to workers contacting to this substance.

  20. Numerical modeling of wind-blown sand on Mars.

    Science.gov (United States)

    Huang, HaoJie; Bo, TianLi; Zheng, XiaoJing

    2014-09-01

    Recent observation results show that sand ripples and dunes are movable like those on Earth under current Martian climate. And the aeolian process on Mars therefore is re-attracting the eyes of scientific researchers in different fields. In this paper, the spatial and temporal evolution of wind-blown sand on Mars is simulated by the large-eddy simulation method. The simulations are conducted under the conditions of both friction wind speed higher and lower than the "fluid threshold", respectively. The fluid entrainment of the sand particles, the processes among saltation sand particles and sand bed, and the negative feedback of sand movement to flow field are considered. Our results show that the "overshoot" phenomenon also exists in the evolution of wind-blown sand on Mars both temporally and spatially; impact entrainment affects the sand transport rate on Mars when the wind speed is smaller or larger than the fluid threshold; and both the average saltation length and height are one order of magnitudes larger than those on Earth. Eventually, the formulas describing the sand transport rate, average saltation length and height on Mars are given, respectively.

  1. Sand control mechanism analysis of metallic wool screen

    Energy Technology Data Exchange (ETDEWEB)

    Yongquan, H.; Jinzhou, Z.; Zhinjun, W.; Zhaofeng, L. [Southwest Petroleum Institute, China, (China); Lei, Y. [Liaohe petroleum Administration, China, (China)

    1997-08-01

    A filter prepacked with metallic wool was developed and claimed to have been effectively used on thermal and unconsolidated sand oil wells. Structural features of the filter screen and the factors having a bearing on its sand control function, such as particle characteristics, fluid properties, environmental conditions, and the filtering characteristics of metallic wool, were discussed. Some experimental results have been provided to illustrate desirable characteristics and advantages. According to this evidence, sanding velocity is highest at the beginning, stabilizing gradually. Production pressure drop must be appropriately adjusted to achieve best results with well sanding control. 9 refs., 1 tab., 5 figs.

  2. Trajectories of saltating sand particles behind a porous fence

    Science.gov (United States)

    Zhang, Ning; Lee, Sang Joon; Chen, Ting-Guo

    2015-01-01

    Trajectories of aeolian sand particles behind a porous wind fence embedded in a simulated atmospheric boundary layer were visualized experimentally, to investigate the shelter effect of the fence on sand saltation. Two sand samples, one collected from a beach (d = 250 μm) and the other from a desert (d = 100 μm), were tested in comparison with the previous studies of a 'no-fence' case. A wind fence (ε = 38.5%) was installed on a flat sand bed filled with each sand sample. A high-speed photography technique and the particle tracking velocimetry (PTV) method were employed to reconstruct the trajectories of particles saltating behind the fence. The collision processes of these sand particles were analyzed, momentum and kinetic energy transfer between saltating particles and ground surface were also investigated. In the wake region, probability density distributions of the impact velocities agree well with the pattern of no-fence case, and can be explained by a log-normal law. The horizontal component of impact velocity for the beach sand is decreased by about 54%, and about 76% for the desert sand. Vertical restitution coefficients of bouncing particles are smaller than 1.0 due to the presence of the wind fence. The saltating particles lose a large proportion of their energy during the collision process. These results illustrate that the porous wind fence effectively abates the further evolution of saltating sand particles.

  3. Effective Laboratory Method of Chromite Content Estimation in Reclaimed Sands

    Directory of Open Access Journals (Sweden)

    Ignaszak Z.

    2016-09-01

    Full Text Available The paper presents an original method of measuring the actual chromite content in the circulating moulding sand of foundry. This type of material is applied for production of moulds. This is the case of foundry which most frequently perform heavy casting in which for the construction of chemical hardening mould is used, both the quartz sand and chromite sand. After the dry reclamation of used moulding sand, both types of sands are mixed in various ratios resulting that in reclaimed sand silos, the layers of varying content of chromite in mixture are observed. For chromite recuperation from the circulating moulding sand there are applied the appropriate installations equipped with separate elements generating locally strong magnetic field. The knowledge of the current ratio of chromite and quartz sand allows to optimize the settings of installation and control of the separation efficiency. The arduous and time-consuming method of determining the content of chromite using bromoform liquid requires operational powers and precautions during using this toxic liquid. It was developed and tested the new, uncomplicated gravimetric laboratory method using powerful permanent magnets (neodymium. The method is used in the production conditions of casting for current inspection of chromite quantity in used sand in reclamation plant.

  4. Geologic and paleoecologic studies of the Nebraska Sand Hills

    Science.gov (United States)

    Ahlbrandt, Thomas S.; Fryberger, S.G.; Hanley, John H.; Bradbury, J. Platt

    1980-01-01

    PART A: The Nebraska Sand Hills are an inactive, late Quaternary, most probably Holocene, dune field (covering 57,000 km 2 ) that have been eroded along streams and in blowouts, resulting in excellent lateral and vertical exposures of the stratification of dune and interdune sediments. This paper presents new data on the geometry, primary sedimentary structures, modification of sedimentary structures, direction of sand movement, and petrography of these eolian deposits. Eolian deposits of the Sand Hills occur as relatively thin (9-24 m) 'blanket' sands, composed of a complex of dune and discontinuous, diachronous interdune deposits unconformably overlying fluviolacustrine sediments. The internal stratification of large dunes in the Sand Hills (as high as 100 m), is similar to the internal stratification of smaller dunes of the same type in the Sand Hills, differing only in scale. Studies of laminae orientation in the Sand Hills indicate that transverse, barchan, and blowout dunes can be differentiated in rocks of eolian origin using both the mean dip angle of laminae and the mean angular deviation of dip direction. A variety of secondary structures modify or replace primary eolian stratification in the Sand Hills, the more common of which are dissipation structures and bioturbation. Dissipation structures in the Sand Hills may develop when infiltrating water deposits clay adjacent to less permeable layers in the sand, or along the upper margins of frozen layers that form in the sands during winter. Cross-bed measurements from dunes of the Nebraska Sand Hills necessitate a new interpretation of the past sand transport directions. The data from these measurements indicate a general northwest-to-southeast drift of sand, with a more southerly drift in the southeast part of the Sand Hills. A large area of small dunes Sand Hills was interpreted by him on the basis of morphology only. We interpret these as transverse-ridge dunes that were generally moving to the south

  5. Importance of motion in motion-compensated temporal discrete wavelet transforms

    Science.gov (United States)

    Konrad, Janusz; Bozinovic, Nikola

    2005-03-01

    Discrete wavelet transforms (DWTs) applied temporally under motion compensation (MC) have recently become a very powerful tool in video compression, especially when implemented through lifting. A recent theoretical analysis has established conditions for perfect reconstruction in the case of transversal MC-DWT, and also for the equivalence of lifted and transversal implementations of MC-DWT. For Haar MC-DWT these conditions state that motion must be invertible, while for higher-order transforms they state that motion composition must be a well-defined operator. Since many popular motion models do not obey these properties, thus inducing errors (prior to compression), it is important to understand what is the impact of motion non-invertibility or quasi-invertibility on the performance of video compression. In this paper, we present new experimental results of a study aiming at a quantitative evaluation of such impact in case of block-based motion. We propose a new metric to measure the degree with which two motion fields are not inverses of each other. Using this metric we investigate several motion inversion schemes, from simple temporal sample-and-hold, through spatial nearest-neighbor, to advanced spline-based inversion, and we compare compression performance of each method to that of independently-estimated forward and backward motion fields. We observe that compression performance monotonically improves with the reduction of the proposed motion inversion error, up to 1-1.5dB for the advanced spline-based inversion. We also generalize the problem of "unconnected" pixels by extending it to both update and prediction steps, as opposed to the update step only used in conventional methods. Initial tests show favorable results compared to previously reported techniques.

  6. Co-occurrence of methanogenesis and N{sub 2} fixation in oil sands tailings

    Energy Technology Data Exchange (ETDEWEB)

    Collins, C.E. Victoria [Department of Renewable Resources, University of Alberta, Edmonton, AB T6G 2G7 (Canada); Foght, Julia M. [Department of Biological Sciences, University of Alberta, Edmonton, AB T6G 2E9 (Canada); Siddique, Tariq, E-mail: tariq.siddique@ualberta.ca [Department of Renewable Resources, University of Alberta, Edmonton, AB T6G 2G7 (Canada)

    2016-09-15

    Oil sands tailings ponds in northern Alberta, Canada have been producing biogenic gases via microbial metabolism of hydrocarbons for decades. Persistent methanogenic activity in tailings ponds without any known replenishment of nutrients such as fixed nitrogen (N) persuaded us to investigate whether N{sub 2} fixation or polyacrylamide (PAM; used as a tailings flocculant) could serve as N sources. Cultures comprising mature fine tailings (MFT) plus methanogenic medium supplemented with or deficient in fixed N were incubated under an N{sub 2} headspace. Some cultures were further amended with citrate, which is used in oil sands processing, as a relevant carbon source, and/or with PAM. After an initial delay, N-deficient cultures with or without PAM produced methane (CH{sub 4}) at the same rate as N-containing cultures, indicating a mechanism of overcoming apparent N-deficiency. Acetylene reduction and {sup 15}N{sub 2} incorporation in all N-deficient cultures (with or without PAM) suggested active N{sub 2} fixation concurrently with methanogenesis but inability to use PAM as a N source. 16S rRNA gene pyrosequencing revealed little difference between archaeal populations regardless of N content. However, bacterial sequences in N-deficient cultures showed enrichment of Hyphomicrobiaceae and Clostridium members that might contain N{sub 2}-fixing species. The results are important in understanding long-term production of biogenic greenhouse gases in oil sands tailings. - Highlights: • Methanogenesis in oil sands tailings can occur under nitrogen depleted conditions. • {sup 15}N{sub 2} isotopic analysis reveals that indigenous microbes can fix N{sub 2} for microbial metabolism and methanogenesis. • 16S rRNA gene analysis suggests that members of Hyphomicrobiaceae and Clostridium may be involved in N{sub 2} fixation. • This is the first report that describes co-occurrence of methanogenesis and nitrogen fixation in oil sands tailings.

  7. The effect of oil sands tailings pond sediments on embryo-larval walleye (Sander vitreus).

    Science.gov (United States)

    Raine, J C; Turcotte, D; Tumber, V; Peru, K M; Wang, Z; Yang, C; Headley, J V; Parrott, J L

    2017-10-01

    Walleye (Sander vitreus) are a commercially important North American fish species that inhabit the Athabasca River. This river flows through the Athabasca oil sands where natural sources of bitumen erode from the McMurray formation. Little information is available on responses of walleye embryos to oil sands tailings pond sediments in a laboratory setting. The current study describes the design and implementation of a daily-renewal bioassay to assess the potential effects of tailings pond sediments from the Athabasca oil sands area on walleye development. Developing walleye embryos were exposed to increasing concentrations of two tailings pond sediments (collected in the Athabasca oil sands area) until the completion of yolk absorption in control fish. Sediments from the tailings pond represent a mixture of polycyclic aromatic hydrocarbons (PAHs) and alkylated PAHs. During the 31 day exposure, the walleye were examined for mortalities, weight, length and developmental abnormalities to provide an initial evaluation of the effects of the oil sands tailings pond sediments. Walleye embryo survival differed between the tailings pond sediments, and survival decreased with increasing sediment concentration. Alkylated PAH content differed between the two tailings pond sediments and lower embryo survival corresponded to higher total and alkylated PAH content. Tailings pond sediment-exposed walleye exhibited a delay in development, as well as increased percentages of larvae with heart and yolk sac edema, and cranial and spinal malformations. These abnormalities in development are often associated with PAH and alkylated PAH exposure. This study provides an exposure design that can be used to assess sediment toxicity to early developmental stages of a fish species not commonly tested in the lab, and lays the groundwork for future studies with this and other difficult-to-culture species. These results offer information on the potential effects of tailings pond sediments

  8. PROMOTIONS: PROper MOTION Software

    Science.gov (United States)

    Caleb Wherry, John; Sahai, R.

    2009-05-01

    We report on the development of a software tool (PROMOTIONS) to streamline the process of measuring proper motions of material in expanding nebulae. Our tool makes use of IDL's widget programming capabilities to design a unique GUI that is used to compare images of the objects from two epochs. The software allows us to first orient and register the images to a common frame of reference and pixel scale, using field stars in each of the images. We then cross-correlate specific morphological features in order to determine their proper motions, which consist of the proper motion of the nebula as a whole (PM-neb), and expansion motions of the features relative to the center. If the central star is not visible (quite common in bipolar nebulae with dense dusty waists), point-symmetric expansion is assumed and we use the average motion of high-quality symmetric pairs of features on opposite sides of the nebular center to compute PM-neb. This is then subtracted out to determine the individual movements of these and additional features relative to the nebular center. PROMOTIONS should find wide applicability in measuring proper motions in astrophysical objects such as the expanding outflows/jets commonly seen around young and dying stars. We present first results from using PROMOTIONS to successfully measure proper motions in several pre-planetary nebulae (transition objects between the red giant and planetary nebula phases), using images taken 7-10 years apart with the WFPC2 and ACS instruments on board HST. The authors are grateful to NASA's Undergradute Scholars Research Program (USRP) for supporting this research.

  9. Falling sand tests on various coatings

    Energy Technology Data Exchange (ETDEWEB)

    Manetti, M.; Zonfrillo, G.; Pratesi, F. [Florence Univ. (Italy). Dipt. di Meccanica e Tecnologie Industriali; Giovannetti, I. [GE Oil and Gas - Nuovo Pilnone, Florence (Italy)

    2010-07-01

    Abrasive wear is responsible for severe machine parts and in particular of compressor impellers. Methods of increasing service lifetime are based on employment of abrasion resistant materials or more frequently of the creation of hard, wear-resistant surface layers. In this work a bare aluminium alloy and the same alloy with four different coatings have been tested at room temperature, in order to verify their resistance to falling abrasive. Following standard ASTM D968-93, tests have been performed using a precise quantity of sand as abrasive and letting it fall on the sample with a standard apparatus: two different kinds of sand have been used, in order to obtain also information on the influence of composition and Grain size of the abrasive on material resistance. Determinations of hardness, roughness, weight loss, and morphology of the eroded surface have also been carried out. The comparison between the coatings in vestilated has been performed on the basis of the thickness decrease of the samples. (orig.)

  10. Sulfur biogeochemistry of oil sands composite tailings

    Energy Technology Data Exchange (ETDEWEB)

    Warren, Lesley; Stephenson, Kate [Earth Sciences, McMaster University (Canada)], email: warrenl@mcmaster.ca; Penner, Tara [Syncrude Environmental Research (Canada)

    2011-07-01

    This paper discusses the sulfur biogeochemistry of oil sands composite tailings (CT). The Government of Alberta is accelerating reclamation activities on composite tailings. As a CT pilot reclamation operation, Syncrude is currently constructing the first freshwater fen. Minor unpredicted incidents with H2S gas released from the dewatering process associated with these reclamations have been reported. The objective of this study is to ascertain the connection between microbial activity and H2S generation within CT and to assess the sulfur biogeochemistry of untreated and treated (fen) CT over seasonal and annual timescales. The microbial geochemical interactions taking place are shown using a flow chart. CT is composed of gypsum, sand, clay and organics like naphthenic acids and bitumen. Sulfur and Fe cycling in mining systems and their microbial activities are presented. The chemistry and the processes involved within CT are also given along with the results. It can be said that the diverse Fe and S metabolizing microorganisms confirm the ecology involved in H2S dynamics.

  11. TESTING OF TMR SAND MANTIS FINAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Krementz, D; William Daugherty, W

    2007-06-12

    Screening tests of Sand Mantis candidate materials selected for erosion resistance have been completed. The results of this testing identified that over a relatively short period of operation (<1 hour), measurable erosion will occur in each of the candidate zoom tube materials given equal operating exposure. Additionally, this testing has shown that erosion of the rubber discharge hose directly downstream of the vehicle could be expected to limit the service life of the discharge hose. On the basis of these test results, SRNL recommends the following; {lg_bullet} redesign of critical system components (e.g., zoom tube, discharge hose) should be conducted to improve system characteristics relative to erosion and capitalize on the results of this testing, {lg_bullet} continued efforts to deploy the Sand Mantis should include testing to better define and optimize operating parameters, and gain an understanding of system dynamics, {lg_bullet} discontinue wear testing with the selected materials pending redesign of critical system components (1st recommendation) and inclusion of other candidate materials. The final selection of additional candidate materials should be made following design changes, but might include a Stellite alloy or zirconia.

  12. Microstructural characterization of a Canadian oil sand

    CERN Document Server

    Dinh, Hong Doan; Nauroy, Jean-François; Tang, Anh-Minh; Souhail, Youssef; 10.1139/T2012-072

    2013-01-01

    The microstructure of oil sand samples extracted at a depth of 75 m from the estuarine Middle McMurray formation (Alberta, Canada) has been investigated by using high resolution 3D X-Ray microtomography ($\\mu$CT) and Cryo Scanning Electron Microscopy (CryoSEM). $\\mu$CT images evidenced some dense areas composed of highly angular grains surrounded by fluids that are separated by larger pores full of gas. 3D Image analysis provided in dense areas porosity values compatible with in-situ log data and macroscopic laboratory determinations, showing that they are representative of intact states. $\\mu$CT hence provided some information on the morphology of the cracks and disturbance created by gas expansion. The CryoSEM technique, in which the sample is freeze fractured within the SEM chamber prior to observation, provided pictures in which the (frozen) bitumen clearly appears between the sand grains. No evidence of the existence of a thin connate water layer between grains and the bitumen, frequently mentioned in th...

  13. Western Gas Sands Project: status report

    Energy Technology Data Exchange (ETDEWEB)

    1978-05-01

    Progress of the major government sponsored projects undertaken to increase gas production from low permeability gas sands of the western United States during March 1978 is summarized. The Bartlesville Energy Research Center (BERC) and participating National Laboratories, funded by DOE, are continuing their work in the area of research and development. The emphasis is on the development of new tools and instrumentation systems, rock mechanics, mathematical modeling and data analysis. Field Tests and demonstrations active in the Uinta and Piceance Basins include: Gas Producing Enterprises (GPE) Natural Buttes Unit Wells No. 9, 14, 18, 19, 20, 21 and 22, Mobil Research and Development Corporation, Well No. F-31-13G, and Rio Blanco Natural Gas Company, Well No. 498-4-1. Gas Producing Enterprises Natural Buttes Unit Well No. 9 was fractured on March 27, 1978. The treatment consisted of 554,000 pounds of sand and 349,000 gallons of gel. Mitchell Energy Corporation of Houston, Texas was awarded Department of Energy Contract EF-78-C-08-1547 on March 15, 1978. Field work under this contract is scheduled to begin on June 15, 1978, with the drilling of a new well.

  14. Motion Belts: Visualization of Human Motion Data on a Timeline

    Science.gov (United States)

    Yasuda, Hiroshi; Kaihara, Ryota; Saito, Suguru; Nakajima, Masayuki

    Because motion capture system enabled us to capture a number of human motions, the demand for a method to easily browse the captured motion database has been increasing. In this paper, we propose a method to generate simple visual outlines of motion clips, for the purpose of efficient motion data browsing. Our method unfolds a motion clip into a 2D stripe of keyframes along a timeline that is based on semantic keyframe extraction and the best view point selection for each keyframes. With our visualization, timing and order of actions in the motions are clearly visible and the contents of multiple motions are easily comparable. In addition, because our method is applicable for a wide variety of motions, it can generate outlines for a large amount of motions fully automatically.

  15. Adaptation to life in aeolian sand: how the sandfish lizard, Scincus scincus, prevents sand particles from entering its lungs

    OpenAIRE

    Stadler, Anna T.; Vihar, Boštjan; Günther, Mathias; Huemer, Michaela; Riedl, Martin; Shamiyeh, Stephanie; Mayrhofer, Bernhard; Böhme, Wolfgang; Baumgartner, Werner

    2016-01-01

    ABSTRACT The sandfish lizard, Scincus scincus (Squamata: Scincidae), spends nearly its whole life in aeolian sand and only comes to the surface for foraging, defecating and mating. It is not yet understood how the animal can respire without sand particles entering its respiratory organs when buried under thick layers of sand. In this work, we integrated biological studies, computational calculations and physical experiments to understand this phenomenon. We present a 3D model of the upper res...

  16. Comparison of buried sand ridges and regressive sand ridges on the outer shelf of the East China Sea

    Science.gov (United States)

    Wu, Ziyin; Jin, Xianglong; Zhou, Jieqiong; Zhao, Dineng; Shang, Jihong; Li, Shoujun; Cao, Zhenyi; Liang, Yuyang

    2016-07-01

    Based on multi-beam echo soundings and high-resolution single-channel seismic profiles, linear sand ridges in U14 and U2 on the East China Sea (ECS) shelf are identified and compared in detail. Linear sand ridges in U14 are buried sand ridges, which are 90 m below the seafloor. It is presumed that these buried sand ridges belong to the transgressive systems tract (TST) formed 320-200 ka ago and that their top interface is the maximal flooding surface (MFS). Linear sand ridges in U2 are regressive sand ridges. It is presumed that these buried sand ridges belong to the TST of the last glacial maximum (LGM) and that their top interface is the MFS of the LGM. Four sub-stage sand ridges of U2 are discerned from the high-resolution single-channel seismic profile and four strikes of regressive sand ridges are distinguished from the submarine topographic map based on the multi-beam echo soundings. These multi-stage and multi-strike linear sand ridges are the response of, and evidence for, the evolution of submarine topography with respect to sea-level fluctuations since the LGM. Although the difference in the age of formation between U14 and U2 is 200 ka and their sequences are 90 m apart, the general strikes of the sand ridges are similar. This indicates that the basic configuration of tidal waves on the ECS shelf has been stable for the last 200 ka. A basic evolutionary model of the strata of the ECS shelf is proposed, in which sea-level change is the controlling factor. During the sea-level change of about 100 ka, five to six strata are developed and the sand ridges develop in the TST. A similar story of the evolution of paleo-topography on the ECS shelf has been repeated during the last 300 ka.

  17. Comparison of buried sand ridges and regressive sand ridges on the outer shelf of the East China Sea

    Science.gov (United States)

    Wu, Ziyin; Jin, Xianglong; Zhou, Jieqiong; Zhao, Dineng; Shang, Jihong; Li, Shoujun; Cao, Zhenyi; Liang, Yuyang

    2017-06-01

    Based on multi-beam echo soundings and high-resolution single-channel seismic profiles, linear sand ridges in U14 and U2 on the East China Sea (ECS) shelf are identified and compared in detail. Linear sand ridges in U14 are buried sand ridges, which are 90 m below the seafloor. It is presumed that these buried sand ridges belong to the transgressive systems tract (TST) formed 320-200 ka ago and that their top interface is the maximal flooding surface (MFS). Linear sand ridges in U2 are regressive sand ridges. It is presumed that these buried sand ridges belong to the TST of the last glacial maximum (LGM) and that their top interface is the MFS of the LGM. Four sub-stage sand ridges of U2 are discerned from the high-resolution single-channel seismic profile and four strikes of regressive sand ridges are distinguished from the submarine topographic map based on the multi-beam echo soundings. These multi-stage and multi-strike linear sand ridges are the response of, and evidence for, the evolution of submarine topography with respect to sea-level fluctuations since the LGM. Although the difference in the age of formation between U14 and U2 is 200 ka and their sequences are 90 m apart, the general strikes of the sand ridges are similar. This indicates that the basic configuration of tidal waves on the ECS shelf has been stable for the last 200 ka. A basic evolutionary model of the strata of the ECS shelf is proposed, in which sea-level change is the controlling factor. During the sea-level change of about 100 ka, five to six strata are developed and the sand ridges develop in the TST. A similar story of the evolution of paleo-topography on the ECS shelf has been repeated during the last 300 ka.

  18. A model of motion transparency processing with local center-surround interactions and feedback.

    Science.gov (United States)

    Raudies, Florian; Mingolla, Ennio; Neumann, Heiko

    2011-11-01

    Motion transparency occurs when multiple coherent motions are perceived in one spatial location. Imagine, for instance, looking out of the window of a bus on a bright day, where the world outside the window is passing by and movements of passengers inside the bus are reflected in the window. The overlay of both motions at the window leads to motion transparency, which is challenging to process. Noisy and ambiguous motion signals can be reduced using a competition mechanism for all encoded motions in one spatial location. Such a competition, however, leads to the suppression of multiple peak responses that encode different motions, as only the strongest response tends to survive. As a solution, we suggest a local center-surround competition for population-encoded motion directions and speeds. Similar motions are supported, and dissimilar ones are separated, by representing them as multiple activations, which occurs in the case of motion transparency. Psychophysical findings, such as motion attraction and repulsion for motion transparency displays, can be explained by this local competition. Besides this local competition mechanism, we show that feedback signals improve the processing of motion transparency. A discrimination task for transparent versus opaque motion is simulated, where motion transparency is generated by superimposing large field motion patterns of either varying size or varying coherence of motion. The model's perceptual thresholds with and without feedback are calculated. We demonstrate that initially weak peak responses can be enhanced and stabilized through modulatory feedback signals from higher stages of processing.

  19. Complexity scalable motion estimation for H.264/AVC

    Science.gov (United States)

    Kim, Changsung; Xin, Jun; Vetro, Anthony; Kuo, C.-C. Jay

    2006-01-01

    A new complexity-scalable framework for motion estimation is proposed to efficiently reduce the motioncomplexity of encoding process, with focus on long term memory motion-compensated prediction of the H.264 video coding standard in this work. The objective is to provide a complexity scalable scheme for the given motion estimation algorithm such that it reduces the encoding complexity to the desired level with insignificant penalty in rate-distortion performance. In principle, the proposed algorithm adaptively allocates available motion-complexity budget to macroblock based on estimated impact towards overall rate-distortion (RD) performance subject to the given encoding time limit. To estimate macroblock-wise tradeoff between RD coding gain (J) and motion-complexity (C), the correlation of J-C curve between current macroblock and collocated macroblock in previous frame is exploited to predict initial motion-complexity budget of current macroblock. The initial budget is adaptively assigned to each blocksize and block-partition successively and motion-complexity budget is updated at the end of every encoding unit for remaining ones. Based on experiment, proposed J-C slope based allocation is better than uniform motion-complexity allocation scheme in terms of RDC tradeoff. It is demonstrated by experimental results that the proposed algorithm can reduce the H.264 motion estimation complexity to the desired level with little degradation in the rate distortion performance.

  20. Field investigation of surface sand and dust movement over different sandy grasslands in the Otindag Sandy Land, China

    Science.gov (United States)

    Liu, Shulin; Wang, Tao; Chen, Guangting; Guo, Jian; Xue, Xian; Ma, Shaoxiu

    2008-01-01

    The characteristics of sand and dust movement over different sandy grasslands in China’s Otindag Sandy Land were explored based on field observations and laboratory analyses. Threshold wind speeds (the speed required to initiate sand movement) at a height of 2 m above the ground were estimated in the field for different surface types. Threshold wind speed above shifting dunes in the study area is about 4.6 m s-1 at this height. This value was smaller than values observed above other surfaces, resulting in a greater risk of blowing sand above these dunes. Differences in sand transport rates (STR) as a function of the severity of desertification resulted primarily from differences in surface vegetation cover and secondarily from the soil’s grain-size distribution. STR increased exponentially with increasing near-bed wind velocity. Under the same wind conditions, STR increased with increasing severity of desertification: from 0.08 g cm-2 min-1 above semi-fixed dunes to 8 g cm-2 min-1 above semi-shifting dunes and 25 g cm-2 min-1 above shifting dunes. Vegetation’s affect on STR was clearly large. Different components of sand and dust were trapped over different lands: mostly sand grains but little dust were trapped above shifting dunes, but much dust was collected over semi-shifting and semi-fixed dunes. Human disturbance is likely to produce dust even from fixed dunes as a result of trampling by animals and vehicle travel. In addition, spring rainfall decreased the risk of sand and dust movement by accelerating germination of plants and the formation of a soil crust.

  1. Biodegradation rates of 2-methylisoborneol (MIB) and geosmin through sand filters and in bioreactors.

    Science.gov (United States)

    Ho, Lionel; Hoefel, Daniel; Bock, Franziska; Saint, Christopher P; Newcombe, Gayle

    2007-02-01

    Taste and odour (T&O) causing compounds, in particular, 2-methylisoborneol (MIB) and geosmin, are a problem for water authorities as they are recalcitrant to conventional water treatment. In this study, biological sand filtration was shown to be an effective process for the complete removal of MIB and geosmin, with removal shown to be predominantly through biodegradation. In addition, MIB and geosmin were also effectively degraded in batch bioreactor experiments using biofilm sourced from one of the sand filters as the microbial inoculum. The biodegradation of MIB and geosmin was determined to be a pseudo-first-order reaction with rate constants ranging between 0.10 and 0.58 d(-1) in the bioreactor experiments. Rate constants were shown to be dependent upon the initial concentration of the microbial inoculum but not the initial concentration of MIB and geosmin when target concentrations of 200 and 50 ng l(-1) were used. Furthermore, rate constants were shown to increase upon re-exposure of the biofilm to both T&O compounds. Enrichment cultures with subsequent community profile analysis using 16S rRNA-directed PCR-DGGE identified four bacteria most likely involved in the biodegradation of geosmin within the sand filters and bioreactors. These included a Pseudomonas sp., Alphaproteobacterium, Sphingomonas sp. and an Acidobacteriaceae member.

  2. MACHINE MOTION EQUATIONS

    Directory of Open Access Journals (Sweden)

    Florian Ion Tiberiu Petrescu

    2015-09-01

    Full Text Available This paper presents the dynamic, original, machine motion equations. The equation of motion of the machine that generates angular speed of the shaft (which varies with position and rotation speed is deduced by conservation kinetic energy of the machine. An additional variation of angular speed is added by multiplying by the coefficient dynamic D (generated by the forces out of mechanism and or by the forces generated by the elasticity of the system. Kinetic energy conservation shows angular speed variation (from the shaft with inertial masses, while the dynamic coefficient introduces the variation of w with forces acting in the mechanism. Deriving the first equation of motion of the machine one can obtain the second equation of motion dynamic. From the second equation of motion of the machine it determines the angular acceleration of the shaft. It shows the distribution of the forces on the mechanism to the internal combustion heat engines. Dynamic, the velocities can be distributed in the same way as forces. Practically, in the dynamic regimes, the velocities have the same timing as the forces. Calculations should be made for an engine with a single cylinder. Originally exemplification is done for a classic distribution mechanism, and then even the module B distribution mechanism of an Otto engine type.

  3. Distribution of sand dunes and sand shifts along the southern fringe of the Mu Us Desert since the Ming Dynasty

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    This article takes the two segments of the Ming Great Walls, Dabian and Erbian, and their associated barracks and forts as geographical references. Based on a detailed scrutiny of historical records of the Ming and Qing dynasties, and on field surveys, the southern boundaries of the sand dunes and sand shifts of the Mu Us Desert in the Ming and Qing dynasties are carefully reconstructed. A comparison of the southern boundaries of the sand dunes and sand shifts of the Mu Us Desert in Ming and Qing with the modern boundary revealed in remote sensing imagery clearly shows that the southern boundary of dunes and shifts in the Mu us Desert has expanded only in a few areas and on a small scale. In the area to the south of Changle Fort, along the direction of annually prevailing winds, sand drifts have penetrated through the Jialu River valley into the loess region and have formed a sand strip of 32 km long and 3 km wide. To the east of Qingping Fort, sand drifts penetrated toward the eastern loess region through the Luhe River valley and have formed another sand strip of 8 km long and 2 km wide. Generally speaking, though the intensity of human activity has been increasing in this area since the Ming Dynasty, the Mu Us Desert has not significantly expanded toward the southeast or southwest. The sand-loess boundary in the southern fringe of the Mu Us Desert has been almost unchanged since the Ming Dynasty.

  4. Faecal indicator bacteria enumeration in beach sand: A comparison study of extraction methods in medium to coarse sands

    Science.gov (United States)

    Boehm, A.B.; Griffith, J.; McGee, C.; Edge, T.A.; Solo-Gabriele, H. M.; Whitman, R.; Cao, Y.; Getrich, M.; Jay, J.A.; Ferguson, D.; Goodwin, K.D.; Lee, C.M.; Madison, M.; Weisberg, S.B.

    2009-01-01

    Aims: The absence of standardized methods for quantifying faecal indicator bacteria (FIB) in sand hinders comparison of results across studies. The purpose of the study was to compare methods for extraction of faecal bacteria from sands and recommend a standardized extraction technique. Methods and Results: Twenty-two methods of extracting enterococci and Escherichia coli from sand were evaluated, including multiple permutations of hand shaking, mechanical shaking, blending, sonication, number of rinses, settling time, eluant-to-sand ratio, eluant composition, prefiltration and type of decantation. Tests were performed on sands from California, Florida and Lake Michigan. Most extraction parameters did not significantly affect bacterial enumeration. anova revealed significant effects of eluant composition and blending; with both sodium metaphosphate buffer and blending producing reduced counts. Conclusions: The simplest extraction method that produced the highest FIB recoveries consisted of 2 min of hand shaking in phosphate-buffered saline or deionized water, a 30-s settling time, one-rinse step and a 10 : 1 eluant volume to sand weight ratio. This result was consistent across the sand compositions tested in this study but could vary for other sand types. Significance and Impact of the Study: Method standardization will improve the understanding of how sands affect surface water quality. ?? 2009 The Society for Applied Microbiology.

  5. The Particle--Motion Problem.

    Science.gov (United States)

    Demana, Franklin; Waits, Bert K.

    1993-01-01

    Discusses solutions to real-world linear particle-motion problems using graphing calculators to simulate the motion and traditional analytic methods of calculus. Applications include (1) changing circular or curvilinear motion into linear motion and (2) linear particle accelerators in physics. (MDH)

  6. Interstellar Initiative Web Page Design

    Science.gov (United States)

    Mehta, Alkesh

    1999-01-01

    This summer at NASA/MSFC, I have contributed to two projects: Interstellar Initiative Web Page Design and Lenz's Law Relative Motion Demonstration. In the Web Design Project, I worked on an Outline. The Web Design Outline was developed to provide a foundation for a Hierarchy Tree Structure. The Outline would help design a Website information base for future and near-term missions. The Website would give in-depth information on Propulsion Systems and Interstellar Travel. The Lenz's Law Relative Motion Demonstrator is discussed in this volume by Russell Lee.

  7. Measurement of modulation induced by interaction between bubble motion and liquid-phase motion in the decaying turbulence formed by an oscillating-grid

    Institute of Scientific and Technical Information of China (English)

    Yasuyuki Nagami; Takayuki Saito

    2013-01-01

    In multiphase flows,dynamical gas-liquid interactions are essential for in-depth understanding of their multi-scale phenomena and complicated structures.The purpose of the present study is to clearly extract the modulation in bubble motion and liquid motion induced by bubble-liquid interaction and to discuss the relations between bubble motion and liquid-phase motion.For this particular purpose,the decaying turbulence formed in a cylindrical acrylic pipe (diameter 149 mm,height 600 mm) by using an oscillatinggrid was employed.Uniform single bubbles were launched from an in-house bubble launching device into the decaying turbulence.By comparing the bubble motion in the stagnant water with that in the oscillating-grid decaying turbulence,the transition of the 2D bubble motion (i.e.,zigzagging motion)to 3D motion was enhanced in the latter.In addition,the initial conditions of the bubble motion that was not influenced by the ambient turbulence were carefully confirmed.In the area where the bubble motion started to translate from 2D motion into 3D motion,the modulation of ambient liquid-phase motion was obtained by PIV/LIF measurement.By combining these results,we quantitatively discussed the modulation of the bubble motion and ambient liquid-phase motion and considered the dominant factor for the enhancement to be the bubble-liquid interaction.

  8. Recovery of macrobenthic assemblages following experimental sand burial

    Directory of Open Access Journals (Sweden)

    José J. Barrón

    2008-09-01

    Full Text Available This research was supported by a fund provided by the Instituto de Ciencias del Mar y Limnología (UNAM and a fund provided to Celia Olabarria in 2004 and 2005 by the University of Vigo for overseas short stays.AbstractPeriodic inundation by sand is a very common feature of rocky coasts throughout the world. Even so, there have been few direct observations or experiments to investigate the role of sediments on intertidal rocky shores. We designed a field experiment in Mazatlán Bay, Mexico, to test the initial impact and subsequent recovery of intertidal macrobenthic assemblages exposed to sand burial at two sites of varying wave exposure. Both sites supported different natural assemblages. Treatment plots for the addition of sediment and control plots (50 × 50 cm, separated by at least 1.5 m, were randomly placed across the mid-water tidal level. The initial response of the resident macrobenthos and the subsequent recolonization was monitored over a period of 95 days. The main effect of sediment deposition at both sites was mortality and removal of biota due to smothering. The recovery process was rapid and may in part have been the result of the mechanism by which the small, disturbed patches were recolonized. Most of the invertebrates colonized the patches as adults; several seaweeds exhibited vegetative growth as the major mechanism of colonization (e.g., Ulva lactuca Linnaeus, 1753, Amphiroa valonioides Yendo, 1902 and Chaetomorpha antennina (Borgensen Kutzing, 1849. The rate of recovery varied between the sites, however. Recovery of species numbers proceeded quickly at the sheltered site (day 7, but took 95 days at the exposed site. In contrast, biomass reached control levels by day 45 at the sheltered site, but already by day 15 at the exposed site. By day 95, the assemblages recovered to 83.5% and 81% similarity with the controls at the sheltered and exposed sites respectively. Although differences in wave exposure could be very

  9. Microbial degradation of pesticides in rapid sand filters for treatment of drinking water

    DEFF Research Database (Denmark)

    Hedegaard, Mathilde Jørgensen; Albrechtsen, Hans-Jørgen

    2014-01-01

    to remove pesticides from the water phase and pesticides are detected in 24% of the active Danish waterworks wells. This study aimed at investigating the potential of microbial pesticide removal in rapid sand filters for drinking water treatment. Removal of the pesticides MCPP, bentazone, glyphosate...... of pesticides in the water decreased – MCPP decreased to 42-85%, bentazone to 15-35%, glyphosate to 7-14% and p-nitrophenol 1-3% – from the initial concentration over a period of 6-13 days. The largest microbial removal was observed at Sjælsø waterworks Plant II, where the pesticides were partially mineralised......In Denmark drinking water supply is based on groundwater which is treated by aeration followed by filtration in rapid sand filters. Unfortunately pesticide contamination of the groundwater poses a threat to the water supply, since the simple treatment process at the waterworks is not considered...

  10. Muscle Motion Solenoid Actuator

    Science.gov (United States)

    Obata, Shuji

    It is one of our dreams to mechanically recover the lost body for damaged humans. Realistic humanoid robots composed of such machines require muscle motion actuators controlled by all pulling actions. Particularly, antagonistic pairs of bi-articular muscles are very important in animal's motions. A system of actuators is proposed using the electromagnetic force of the solenoids with the abilities of the stroke length over 10 cm and the strength about 20 N, which are needed to move the real human arm. The devised actuators are based on developments of recent modern electro-magnetic materials, where old time materials can not give such possibility. Composite actuators are controlled by a high ability computer and software making genuine motions.

  11. Properties of Desert Sand and CMAS Glass

    Science.gov (United States)

    Bansal, Narottam P.; Choi, Sung R.

    2014-01-01

    As-received desert sand from a Middle East country has been characterized for its phase composition and thermal stability. X-ray diffraction analysis showed the presence of quartz (SiO2), calcite (CaCO3), gypsum (CaSO4.2H2O), and NaAlSi3O8 phases in as-received desert sand and showed weight loss of approx. 35 percent due to decomposition of CaCO3 and CaSO4.2H2O when heated to 1400 C. A batch of as-received desert sand was melted into calcium magnesium aluminosilicate (CMAS) glass at approx. 1500 C. From inductively coupled plasma-atomic emission spectrometry, chemical composition of the CMAS glass was analyzed to be 27.8CaO-4MgO-5Al2O3-61.6SiO2-0.6Fe2O3-1K2O (mole percent). Various physical, thermal and mechanical properties of the glass have been evaluated. Bulk density of CMAS glass was 2.69 g/cc, Young's modulus 92 GPa, Shear modulus 36 GPa, Poisson's ratio 0.28, dilatometric glass transition temperature (T (sub g)) 706 C, softening point (T (sub d)) 764 C, Vickers microhardness 6.3 +/- 0.4 GPa, indentation fracture toughness 0.75 +/- 0.15 MPa.m (sup 1/2), and coefficient of thermal expansion (CTE) 9.8 x 10 (exp -6)/degC in the temperature range 25 to 700 C. Temperature dependence of viscosity has also been estimated from various reference points of the CMAS glass using the Vogel-Fulcher-Tamman (VFT) equation. The glass remained amorphous after heat treating at 850 C for 10 hr but crystallized into CaSiO3 and Ca-Mg-Al silicate phases at 900 C or higher temperatures. Crystallization kinetics of the CMAS glass has also been investigated by differential thermal analysis (DTA). Activation energies for the crystallization of two different phases in the glass were calculated to be 403 and 483 kJ/mol, respectively.

  12. Ship Roll Motion Control

    DEFF Research Database (Denmark)

    Perez, Tristan; Blanke, Mogens

    2010-01-01

    The technical feasibility of roll motion control devices has been amply demonstrated for over 100 years. Performance, however, can still fall short of expectations because of deciencies in control system designs, which have proven to be far from trivial due to fundamental performance limitations....... This tutorial paper presents an account of the development of various ship roll motion control systems and the challenges associated with their design. The paper discusses how to assess performance, the applicability of dierent models, and control methods that have been applied in the past....

  13. Method through motion

    DEFF Research Database (Denmark)

    Steijn, Arthur

    2016-01-01

    Contemporary scenography often consists of video-projected motion graphics. The field is lacking in academic methods and rigour: descriptions and models relevant for the creation as well as in the analysis of existing works. In order to understand the phenomenon of motion graphics in a scenographic...... construction as a support to working systematically practice-led research project. The design model is being developed through design laboratories and workshops with students and professionals who provide feedback that lead to incremental improvements. Working with this model construction-as-method reveals...

  14. Perpetual Motion Machine

    OpenAIRE

    D. Tsaousis

    2008-01-01

    Ever since the first century A.D. there have been relative descriptions of known devices as well as manufactures for the creation of perpetual motion machines. Although physics has led, with two thermodynamic laws, to the opinion that a perpetual motion machine is impossible to be manufactured, inventors of every age and educational level appear to claim that they have invented something «entirely new» or they have improved somebody else’s invention, which «will function henceforth perpetuall...

  15. Leap Motion development essentials

    CERN Document Server

    Spiegelmock, Mischa

    2013-01-01

    This book is a fast-paced guide with practical examples that aims to help you understand and master the Leap Motion SDK.This book is for developers who are either involved in game development or who are looking to utilize Leap Motion technology in order to create brand new user interaction experiences to distinguish their products from the mass market. You should be comfortable with high-level languages and object-oriented development concepts in order to get the most out of this book.

  16. Mineral Resource Assessment of Marine Sand Resources in Cape- and Ridge-Associated Marine Sand Deposits in Three Tracts, New York and New Jersey, United States Atlantic Continental Shelf

    Science.gov (United States)

    Bliss, James D.; Williams, S. Jeffress; Arsenault, Matthew A.

    2009-01-01

    Demand is growing in the United States and worldwide for information about the geology of offshore continental shelf regions, the character of the seafloor, and sediments comprising the seafloor and subbottom. Interest in locating sand bodies or high quality deposits that have potential as sources for beach nourishment and ecosystem restoration is especially great in some regions of the country. The Atlantic coast, particularly New York and New Jersey, has been the focus of these studies for the past 40 years with widely varying results. This study is the first attempt at applying probability statistics to modeling Holocene-age cape-and ridge-associated sand deposits and thus focuses on distinct sand body morphology. This modeling technique may have application for other continental shelf regions that have similar geologic character and late Quaternary sea-level transgression history. An estimated volume of 3.9 billion m3 of marine sand resources is predicted in the cape-and ridge-associated marine sand deposits in three representative regions or tracts on the continental shelf offshore of New York and New Jersey. These estimates are taken from probabilistic distributions of sand resources and are produced using deposit models and Monte Carlo Simulation (MCS) techniques. The estimated sand resources presented here are for only three tracts as described below and for Holocene age sand resources contained in cape-and ridge-associated marine sand deposit types within this area. Other areas may qualify as tracts for this deposit type and other deposit types and geologic ages (for example, paleo-stream channels, blanket and outwash deposits, ebb-tide shoals, and lower sea level-stand deltas), which are present on the New Jersey and New York continental shelf area but are not delineated and modeled in this initial evaluation. Admittedly, only a portion of these probable sand resources will ultimately be available and suitable for production, dependent largely on

  17. Hand in motion reveals mind in motion

    Directory of Open Access Journals (Sweden)

    Jonathan eFreeman

    2011-04-01

    Full Text Available Recently, researchers have measured hand movements en route to choices on a screen to understand the dynamics of a broad range of psychological processes. We review this growing body of research and explain how manual action exposes the real-time unfolding of underlying cognitive processing. We describe how simple hand motions may be used to continuously index participants’ tentative commitments to different choice alternatives during the evolution of a behavioral response. As such, hand-tracking can provide unusually high-fidelity, real-time motor traces of the mind. These motor traces cast novel theoretical and empirical light onto a wide range of phenomena and serve as a potential bridge between far-reaching areas of psychological science—from language, to high-level cognition and learning, to social cognitive processes.

  18. Silica sand for oil and gas production : a technical market overview

    Energy Technology Data Exchange (ETDEWEB)

    Dawson, J.C. [BJ Services Company, Calgary, AB (Canada)

    2006-07-01

    In order to meet the growing demand for oil, petroleum production companies have initiated aggressive globally oriented drilling programs. In Canada and the United States, the average monthly rig count has doubled from 1103 rigs in 1990 to 2213 in 2006, with 53 per cent of the growth taking place in the last 3 years. Extensive damage occurs in the hydrocarbon rich formations during the drilling process of new wells. In order to stimulate and reconnect the well to the reservoir, completion processes such as hydraulic fracturing, are needed. In hydraulic fracturing, a viscous fluid is injected into the well at a rate and pressure sufficient to initiate a crack behind the casing perforations. When the fracture attains adequate width and length, silica sand or other proppants are added to the fluid to fill the created fracture. These may include Ottawa Sand, Brady Sand, bauxite, intermediate strength ceramics or resin coated sands. The use of proppants prevents the fracture from healing and provides a super conductive drainage channel for hydrocarbons. The proppant should provide the highest porosity to maximize permeability of the proppant pack. Hydrocarbon production can therefore be increased at relatively low costs. This paper reviewed the stringent industry specifications that various grades of proppant must meet, as defined by the American Petroleum Institute. The technical aspects of proppant testing were outlined with reference to proppant size, sphericity, acid solubility, turbidity, crush resistance, and testing for ceramic proppants. Despite improved logging and advances in well stimulation treatments, market trends indicate that hydraulic fracturing and proppants will continue to be an important aspect of oil and gas production. 22 refs., 3 tabs., 5 figs.

  19. Compensation Grouting in Sand: Experiments, Field Experiences and Mechanisms

    NARCIS (Netherlands)

    Bezuijen, A.

    2010-01-01

    This thesis reports on experimental research on compensation grouting in sand. It is investigated in model tests, how the shape of the grout bodies made during injection depends on the grout properties, the density of the sand and the way the tubes are installed. The shape of the grout body affects

  20. Test Setup for Axially Loaded Piles in Sand

    DEFF Research Database (Denmark)

    Thomassen, Kristina

    The test setup for testing axially static and cyclic loaded piles in sand is described in the following. The purpose for the tests is to examine the tensile capacity of axially loaded piles in dense fully saturated sand. The pile dimensions are chosen to resemble full scale dimension of piles used...... in offshore pile foundations today....