Steam versus coking coal and the acid rain program

International Nuclear Information System (INIS)

Lange, Ian

2010-01-01

The Clean Air Act of 1990 initiated a tradable permit program for emissions of sulfur dioxide from coal-fired power plants. One effect of this policy was a large increase in the consumption of low-sulfur bituminous coal by coal-fired power plants. However, low-sulfur bituminous coal is also the ideal coking coal for steel production. The analysis presented here will attempt to determine how the market responded to the increased consumption of low-sulfur bituminous coal by the electricity generation sector. Was there a decrease in the quality and/or quantity of coking coal consumption or did extraction increase? Most evidence suggests that the market for coking coal was unaffected, even as the extraction and consumption of low-sulfur bituminous coal for electricity generation increased substantially.

Coking coal of Checua Lenguazaque area

International Nuclear Information System (INIS)

Arboleda Otalora, Carlos Ariel

1987-06-01

In this report a summary of the main characteristics of the coal of the area of Checua-Samaca is presented. Using the main works carried out on this area, the most important geologic, physical-chemical, technological and petrographic aspects are compiled that are considered essential to carry out a technical evaluation of these coal and all the analyses they take to conclude that in this area, bituminous coal are presented with very good coking properties, on the other hand, it is demonstrated by the use that is given to the coal extracted by the small existent mining. However, keeping in mind the demands of the international market of the coking coal, it becomes necessary to improve the existent geologic information to be able to make reliable stratigraphic correlations

Enrichment of reactive macerals in coal: its characterization and utilization in coke making

Science.gov (United States)

Nag, Debjani; Kopparthi, P.; Dash, P. S.; Saxena, V. K.; Chandra, S.

2018-01-01

Macerals in coal are of different types: reactive and inert. These macerals are differ in their physical and chemical properties. Column flotation method has been used to separate the reactive macerals in a non-coking coal. The enriched coal is then characterized in order to understand the changes in the coking potential by different techniques. It is then used in making of metallurgical coke by proper blending with other coals. Enriched coal enhance the properties of metallurgical coke. This shows a path of utilization of non-coking coal in metallurgical coke making.

Quantification of mineral matter in commercial cokes and their parent coals

Energy Technology Data Exchange (ETDEWEB)

Sakurovs, Richard; French, David; Grigore, Mihaela [CRC for Coal in Sustainable Development, CSIRO Energy Technology, PO Box 330 Newcastle 2300 (Australia)

2007-10-01

The nature of mineral matter in coke is an important factor in determining the behaviour of coke in the blast furnace. However, there have been few quantitative determinations of the types of mineral matter in coke and the feed coal. Here we use a technique of quantitative X-ray diffraction - SIROQUANT trademark - to determine the nature and quantity of mineral matter in eleven cokes and their parent materials, using samples of coals and their cokes utilised commercially in blast furnaces around the world. In some of these coals a considerable proportion of the phosphorus was present as goyazite, an aluminium phosphate. In the cokes, most of the iron was incorporated into amorphous aluminosilicate material; metallic iron accounted for about 15% of the iron present, and a similar amount was present as sulfides. Potassium and sodium were largely present as amorphous aluminosilicate material. Most of the quartz in the coal was unaffected by the coking, but a small fraction was transformed into other minerals. Quartz is not completely inert during coking. The amount of the catalytic forms of iron in the coke - iron, iron oxides and iron sulfides - was not related to the amount of pyrite and siderite in the starting coal, indicating that estimation of catalytic iron requires investigation of the mineral matter in coke directly and cannot be estimated from the minerals in the coal. (author)

The mechanism of coking pressure generation II: Effect of high volatile matter coking coal, semi-anthracite and coke breeze on coking pressure and contraction

Energy Technology Data Exchange (ETDEWEB)

Merrick Mahoney; Seiji Nomura; Koichi Fukuda; Kenji Kato; Anthony Le Bas; David R. Jenkins; Sid McGuire [BHP Billiton Technology, Shortland, NSW (Australia)

2010-07-15

One of the most important aspects of the cokemaking process is to control and limit the coking pressure since excessive coking pressure can lead to operational problems and oven wall damage. Following on from a previous paper on plastic layer permeability we have studied the effect of contraction of semi-coke on coking pressure and the effect of organic additives on contraction. A link between contraction (or simulated contraction) outside the plastic layer and coking pressure was demonstrated. The interaction between this contraction, local bulk density around the plastic layer and the dependence of the permeability of the plastic layer on bulk density was discussed as possible mechanisms for the generation of coking pressure. The effect of blending either a high volatile matter coal or one of two semi-anthracites with low volatile matter, high coking pressure coals on the coking pressure of the binary blends has been explained using this mechanism. 25 refs., 10 figs., 4 tabs.

Effects and mechanistic aspects of absorbing organic compounds by coking coal.

Science.gov (United States)

Ning, Kejia; Wang, Junfeng; Xu, Hongxiang; Sun, Xianfeng; Huang, Gen; Liu, Guowei; Zhou, Lingmei

2017-11-01

Coal is a porous medium and natural absorbent. It can be used for its original purpose after adsorbing organic compounds, its value does not reduce and the pollutants are recycled, and then through systemic circulation of coking wastewater zero emissions can be achieved. Thus, a novel method of industrial organic wastewater treatment using adsorption on coal is introduced. Coking coal was used as an adsorbent in batch adsorption experiments. The quinoline, indole, pyridine and phenol removal efficiencies of coal adsorption were investigated. In addition, several operating parameters which impact removal efficiency such as coking coal consumption, oscillation contact time, initial concentration and pH value were also investigated. The coking coal exhibited properties well-suited for organics' adsorption. The experimental data were fitted to Langmuir and Freundlich isotherms as well as Temkin and Redlich-Peterson (R-P) models. The Freundlich isotherm model provided reasonable models of the adsorption process. Furthermore, the purification mechanism of organic compounds' adsorption on coking coal was analysed.

Binderless briquetting of some selected South African prime coking, blend coking and weathered bituminous coals and the effect of coal properties on binderless briquetting

Energy Technology Data Exchange (ETDEWEB)

Mangena, S.J. [Division of Mining Technology, CSIR, PO Box 395, Pretoria, 0001 (South Africa); du Cann, V.M. [Coal and Mineral Technologies (Pty) Ltd, SABS, PO Box 73656, Lynnwood Ridge, Pretoria, 0040 (South Africa)

2007-07-02

The binderless briquetting of some selected South African prime coking and blend coking coals, as well as the effects of weathering on the binderless briquetting of some inertinite-rich bituminous coals, were investigated in the laboratory. Selected properties of these coals were determined and the coals were briquetted at various moisture contents and pressures. Based on the results obtained in this study, binderless briquetting was found to be most successful in the cases of the fresh, vitrinite-rich coking and blend coking coals and satisfactory in the fresh inertinite-rich Witbank coals. However, the bonding process seemed to be adversely affected by weathering. The negative impact on bonding could be ameliorated to some extent by the presence of a significant kaolinite content when the percentage ash reports in the order of more than 15% (air-dry basis). It should, however, be noted that kaolinite may reduce the water resistance of the briquettes. (author)

Prediction of coking dynamics for wet coal charge

Directory of Open Access Journals (Sweden)

Kardaś Dariusz

2015-09-01

Full Text Available A one-dimensional transient mathematical model describing thermal and flow phenomena during coal coking in an oven chamber was studied in the paper. It also accounts for heat conduction in the ceramic oven wall when assuming a constant temperature at the heating channel side. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. The histories of temperature, gas evolution and internal pressure were presented and analysed. The theoretical predictions of temperature change in the centre plane of the coke oven were compared with industrialscale measurements. Both, the experimental data and obtained numerical results show that moisture content determines the coking process dynamics, lagging the temperature increase above the water steam evaporation temperature and in consequence the total coking time. The phenomenon of internal pressure generation in the context of overlapping effects of simultaneously occurring coal transitions - devolatilisation and coal permeability decrease under plastic stage - was also discussed.

New process of co-coking of waste plastics and blend coal

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Yu, G.; Zhao, P. (and others) [Shougang Technical Research Institute, Beijing (China)

2006-07-01

To recycle and reuse waste plastics, as well as to get a new resource of coking, co-coking process of waste plastics and blend coal has been developed by Nippon Steel. However, the ratio of waste plastics in blend coal should be limited in the range of 1% to maintain the coke strength. This paper suggested a new process of co-coking of waste plastics and blend coal. The new process can add the waste plastics ratio up to 2-4%; when the waste plastics ratio is 2%, the coke strength after reaction with CO{sub 2} (CSR) increased 8%. 8 refs., 2 figs., 3 tabs.

Effects of heat treatments of coal on coke destruction under blast furnace conditions

Energy Technology Data Exchange (ETDEWEB)

Shkoller, M.B.; Dinel' t, V.M.; Korchuganova, G.S.; Petrov, V.B.

1983-09-01

This paper discusses results of investigations on effects of chemical reactions in a blast furnace on coke disintegration and destruction. The investigations were carried out by the VUKhIN Institute branch in Kuznetsk. Effects of silicates and carbonates of sodium, potassium and zinc on mechanical coke properties were investigated under laboratory conditions. Coke samples were placed in a reactor and were treated by vapors of metal compounds. Coke produced from a coal mixture with conventional moisture content and from preheated coal mixture was used. Coal properties are given in a table. Design of laboratory equipment used for tests is shown in 2 schemes. Heat treatments influenced coke porosity and its structural strength. Proportion of large pores accessible to sodium and potassium in coke from preheated coal was 4.5 times lower than in coke from a conventional mixture. Adsorption of sodium and potassium on coke from preheated charge was lower (from 0.22% to 0.24%) than on coke from a conventional mixture (from 2.5% to 2.9%). Adsorption of alkali metals on coke reduced its structural strength and increased coke oxidation rate by carbon dioxide. Use of heat treatments of coal for coking reduced adsorption of alkali metals on coke in a blast furnace, increased coke structural strength and reduced coke oxidation rate by carbon dioxide. (16 refs.) (In Russian)

Achievements and research programs of the Institute for Chemical Coal Processing in the field of conventional coking

Energy Technology Data Exchange (ETDEWEB)

Cieslar, R.; Kaziszyn, I.; Zawistowksi, J.

1986-11-01

This paper describes research programs of the Institute for Chemical Coal Processing in Zabrze on black coal coking and coke use in metallurgy from 1955 to 1990. In 1955-1970 the programs concentrated on coal mixture composition (selective crushing), optimization of coking conditions, mechanical coke treatment. In 1971-1980 research concentrated on coal preparation prior to coking and new coking systems for the Katowice steel plant (heat treatments, design of large coke ovens). The following research programs were implemented in 1981-1985: partial coal charge briquetting, production of foundry coke, coal charge preheating, production of blast furnace coke from black coal from Dobiensko, reducing coke consumption of blast furnaces. In 1986-1990 the Institute will concentrate on the following research programs: coal preparation schemes and coking schemes for coking low-quality weakly caking coals, optimization of coke oven design (e.g. use of packed charge), reducing coke consumption in metallurgy and heating systems, reducing air pollution from coking.

Variation in mineral composition of coal during enrichment and coking

Energy Technology Data Exchange (ETDEWEB)

M.L. Ulanovskii; A.N. Likhenko [Ukrkoks Coke Producers' Association, Dnepropetrovsk (Ukraine)

2009-06-15

The parameters I{sub b} and B{sub b} used in developing an optimal coking-batch composition are determined from data on the chemical composition of the ash in Donetsk Basin and other coal. It is found that, when the ash content is reduced in deeper enrichment of coal with an increased content of fine pyrite, there will be accompanying increase in the Fe{sub 2}O{sub 3} content and decrease in the SiO{sub 2} content of the ash in lighter fractions. This increases I{sub b}. In other words, reducing the ash content of the coal is an unpromising means of increasing CRI and CSR of the coke produced. Three ash-containing elements (silicon, aluminum, and iron) are experimentally proven to transfer from coal to coke. Specific behavior of calcium, magnesium, alkali metals, and sulfur during coking.

Microstructures and microtextures of natural cokes: A case study of heat-affected coking coals from the Jharia coalfield, India

Energy Technology Data Exchange (ETDEWEB)

Singh, Ashok K. [Central Fuel Research Institute, CSIR, Dhanbad-828108 (India); Singh, Mahendra P. [Department of Geology, Banaras Hindu University, Varanasi-221005 (India); Sharma, Mamta; Srivastava, Sunil K.

2007-07-02

In Jharia coalfield, nearly 1250 Mt of coking coal has been devolatilized due to igneous intrusives and {proportional_to} 1900 Mt due to mine fires. This paper is an effort to investigate the effect of carbonization in two intrusive affected coal seams of Ena (seam XIII) and Alkusa (seam XIV) collieries of this coalfield. Through petrographic studies by microscopy, characterization of normal and heat-affected coals was carried out. The microstructures and microtextures produced due to extraneous heat have been related to nature and extent of heat, location of heating source, and quality and quantity of natural coke produced. Based on the results of this study and earlier studies, an effort has been made to study the classification scheme for microtextures of natural cokes generated through in-situ carbonization of the coal seams. It has been observed that in case of such heat effects under overburden pressure, the anisotropy is much more pronounced as compared to laboratory-carbonized cokes. In the mildly carbonized coals (pre-plastic phase, < 300 C) the vitrinite attained higher reflectance than normal vitrinite, liptinite started disappearing, and inertinite remained unaffected. In the moderately affected coals (plastic phase, 300-500 C), mesophase spheres and fused natural cokes were generated from the reactives (vitrinite and liptinite maceral groups), the liptinites disappeared, and structurally, the inertinites remained almost unchanged with slight increase in the reflectance value. In the severely heat-affected coals (post plastic phase, > 500 C) the identified microtextures were mesophase spheres, different shapes and sizes of natural cokes, graphitic sphaeroliths, pyrolytic carbons, inerts with morpho-structural changes and slightly higher reflectance values, and altered and unaltered mineral matters. A gradual change in the heat-affected coals with increasing temperature was observed with respect to location of intrusive body. It has been concluded that

U.S. origin coking coal in the global market : a seismic shift in the global coal market

International Nuclear Information System (INIS)

Thrasher, E.

2010-01-01

This presentation discussed conditions in the global coal market and its impact on producers in the United States (U.S). The significant factors include the strong recovery in Asia, the switch from annual benchmark pricing to quarterly pricing, and the return of U.S. origin coking coal as a long-term supply source for Asia. The global recovery in manufacturing is strong in Asia and weak in more mature economies. A shift in trade patterns has occurred in that 4 of the top 10 destinations for U.S. coking coal exports are now in Asia, up from 1 in 2009, and the tonnage increases to these destinations are at unprecedented levels. Demand for U.S. origin coal will continue to increase as the economies in Western Europe improve and the emerging economies in Eastern Europe and South America grow. Looking at the U.S. coking coal supply, high volume type A coal will be used in the domestic market while high volume type B coal will be used for international demand. Government regulatory agencies create an uncertain environment for investments. Geology and the effects of regulatory actions have decreased productivity. An improvement to the supply chain is that lower cost ocean freight lowers the cost of delivered coal. The prices of coking coal have stabilized at levels that support reasonable returns on investment. The seaborne coking coal market has changed with China's shift to being a significant importer. Mine, rail, and port capacity will constrain the ability of producers in the U.S. to export coking coal to some degree. 2 tabs., 13 figs.

The Bricoke process for producing metallurgical coke in conventional ovens from blends containing a high percentage of non-coking coal

Energy Technology Data Exchange (ETDEWEB)

Vidal, R; Munnix, K; Dellieu, J

1980-06-01

The article discusses the following aspects:- description of the BRICOKE process; trials in pilot plant, showing the influence of the different parameters on the coke quality and delimiting the range of the suitable non-coking coals; industrial scale trials of long term with 33% of non-coking coal briquettes in the charge; influence on the coking process as well as on the blast furnace working and increase of the output of usual coke-oven by the BRICOKE process. (11 refs.)

Geochemical characteristics of oil sands fluid petroleum coke

International Nuclear Information System (INIS)

Nesbitt, Jake A.; Lindsay, Matthew B.J.; Chen, Ning

2017-01-01

The geochemical characteristics of fluid petroleum coke from the Athabasca Oil Sands Region (AOSR) of northern Alberta, Canada were investigated. Continuous core samples were collected to 8 m below surface at several locations (n = 12) from three coke deposits at an active oil sands mine. Bulk elemental analyses revealed the coke composition was dominated by C (84.2 ± 2.3 wt%) and S (6.99 ± 0.26 wt%). Silicon (9210 ± 3000 mg kg"−"1), Al (5980 ± 1200 mg kg"−"1), Fe (4760 ± 1200 mg kg"−"1), and Ti (1380 ± 430 mg kg"−"1) were present in lesser amounts. Vanadium (1280 ± 120 mg kg"−"1) and Ni (230 ± 80 mg kg"−"1) exhibited the highest concentrations among potentially-hazardous minor and trace elements. Sequential extractions revealed potential for release of these metals under field-relevant conditions. Synchrotron powder X-ray diffraction revealed the presence of Si and Ti oxides, organically-complexed V and hydrated Ni sulfate, and provided information about the asphaltenic carbon matrix. X-ray absorption near edge structure (XANES) spectroscopy at the V and Ni K-edges revealed that these metals were largely hosted in porphyrins and similar organic complexes throughout coke grains. Minor differences among measured V and Ni K-edge spectra were largely attributed to slight variations in local coordination of V(IV) and Ni(II) within these organic compounds. However, linear combination fits were improved by including reference spectra for inorganic phases with octahedrally-coordinated V(III) and Ni(II). Sulfur and Fe K-edge XANES confirmed that thiophenic coordination and pyritic-ilmenitic coordination are predominant, respectively. These results provide new information on the geochemical and mineralogical composition of oil sands fluid petroleum coke and improve understanding of potential controls on associated water chemistry. - Highlights: • Oil sands fluid petroleum coke contains wide range of major, minor and

The Release of Trace Elements in the Process of Coal Coking

Directory of Open Access Journals (Sweden)

Jan Konieczyński

2012-01-01

Full Text Available In order to assess the penetration of individual trace elements into the air through their release in the coal coking process, it is necessary to determine the loss of these elements by comparing their contents in the charge coal and in coke obtained. The present research covered four coke oven batteries differing in age, technology, and technical equipment. By using mercury analyzer MA-2 and the method of ICP MS As, Be, Cd, Co, Hg, Mn, Ni, Se, Sr, Tl, V, and Zn were determined in samples of charge coal and yielded coke. Basing on the analyses results, the release coefficients of selected elements were determined. Their values ranged from 0.5 to 94%. High volatility of cadmium, mercury, and thallium was confirmed. The tests have shown that although the results refer to the selected case studies, it may be concluded that the air purity is affected by controlled emission occurring when coke oven batteries are fired by crude coke oven gas. Fugitive emission of the trace elements investigated, occurring due to coke oven leaks and openings, is small and, is not a real threat to the environment except mercury.

Coke production in large coke ovens

Energy Technology Data Exchange (ETDEWEB)

Zhuravskii, A.A.; Sytenko, I.V.; Zhupraner, Z.S.; Vasil' ev, Yu.S.; Karpukhin, E.A.; Pliner, G.E.; Rud' , A.I.; Bulyga, N.I. (NPO Koksokhimiya (USSR))

1990-08-01

Analyzes operation of the No 9 battery with coke ovens with a volume of 41.6 m{sup 3}. Factors that influence coke oven operation and coke quality are analyzed. The following problems are evaluated: composition of coal mixtures (G, Zh, K, OS, GZh coal types), methods for coal mixture preparation (crushing degree, selective crushing), temperature distribution in a coke oven and effects of heating system, coke shrinkage during coking and factors that influence shrinkage, optimizing pressure used for coke pushing, chemical, mechanical and physical properties of coke. Regression equations used for forecasting coke properties are derived: the M10 coke wear index, M25 coke strength index, ash content etc. Recommendations for optimum coking conditions are made. 6 refs.

Non-competitive market behaviour in the international coking coal market

International Nuclear Information System (INIS)

Graham, P.; Thorpe, S.; Hogan, L.

1999-01-01

In this paper, a primal dual programming model of international coking coal trade is constructed to test for non-competitive market behaviour. World trade in 1996 is simulated under perfect competition and various non-competitive market structures. Statistical tests are used to compare simulated trade flows with actual data. Assuming Cournot-Nash behaviour, an all consumer oligopsony market structure is preferred to alternative models. Under an all consumer oligopsony world coking coal prices and trade are lower than under perfect competition. Under an oligopsonistic structure welfare gains from productivity increases in Australian coal mines might largely accrue to coal buyers

Technology for beneficiation of non-coking coals

Energy Technology Data Exchange (ETDEWEB)

Bose, S.K.

1987-04-01

This article outlines the need for efficient non-coking coal beneficiation plants in India to cope with mass production from opencast coal mines. The existing use of magnetite in heavy medium separation processes is expensive and not very efficient in respect to removing shales from opencast lump coals. Instead a new technique is proposed using a ROMJIG washing plant developed in the Federal Republic of Germany. This provides a very efficient, low cost washing system for the coals and allows the continued integration with the coal blending plants. This simplified technology allows for flexible working hours to meet demand and will allow new developments to continue including fuel slurry pipelines, automated testing of coals and new pulverized boiler fuels.

Baking and coking properties of hard coal under high pressure

Energy Technology Data Exchange (ETDEWEB)

Beyer, H.D.

1981-09-01

For a better assessment of the baking and coking properties of hard coal under high pressure as in modern coal beneficiation processes, the determination of the swelling index and the dilatation curve are investigated.

Research of coal flash hydropyrolysis. I. Chemical type analysis of nitrogen in coal and semi-coke

Energy Technology Data Exchange (ETDEWEB)

Zhu, H.; Ni, Y.; Tang, L.; Zheng, Z.; Zhu, Z. [East China University of Science and Technology, Shanghai (China)

2001-04-01

Using XPS analyses the chemical types of nitrogen of ten different types of Chinese coals and their semi-cokes from flash hydropyrolysis (FHP) are studied. The results shows that XPS can effectively determined the chemical types of nitrogen in coal and semi-coke. Peak of XPS located in 398.8 ({plus_minus}0.1) eV and 400.2 ({plus_minus}0.1) eV, which corresponds to pyrrole and pyridine. The nitrogen types are different in coals but mainly are pyrrole and pyridine, and often the pyrrole is more than pyridine. The nitrogen type in coals from FHP is the same as in coal. In FHP, the relative content of pyrrole increases and pyridine reduces. Therefore, it was put forward that flash hydropyrolysis is a new important clean-coal technique and has notable effect of denitrogenation.

Investigating erosion of building materials used in an installation for pneumatic transport of coke breeze and coal

Energy Technology Data Exchange (ETDEWEB)

Bandrowski, J.; Kot-Borkowska, Z.; Misztal, M.; Raczek, J.; Kaczmarzyk, G.

1980-09-01

This article investigates the influence of the following factors on erosion of building material used in pneumatic transport of coal and coke breeze: intensity of coal or coke breeze flow within the range of 47 to 120 kg/h for coke and 99 to 165 kg/h for coal; speed of solid material particles within the range 3.71 to 7.97 m/s for coke, and 3.30 to 7.58 m/s for coal; duration of the experiments 0.5 to 1.5 h for coke and 2.0 to 5.0 for coal; angle of inclination of the sample of building material 30 to 60 degrees for both coal and coke breeze. Three types of construction material used in pneumatic transport were tested: steel, concrete and chamotte bricks. Investigations show that concrete is characterized by the highest erosion, chamotte bricks by medium erosion and steel by the lowest erosion. As a result of mathematical processing of experimental data, empirical models of erosion of the three materials are constructed. (7 refs.)

Upgrading oil sands bitumen with FLUID COKING and FLEXICOKING technologies

Energy Technology Data Exchange (ETDEWEB)

Kamienski, P.; Phillips, G. [ExxonMobil Research and Engineering Co., Fairfax, VA (United States); McKnight, C.; Rumball, B. [Syncrude Canada Ltd., Calgary, AB (Canada)

2009-07-01

This presentation described EMRE's Fluid Coking and Flexicoking technologies that are well suited for upgrading Alberta's heavy crudes and oil sands bitumen into pipelineable crudes or synthetic crudes, which can be further processed into transportation fuels. The Fluid Coking technology uses a fluidized bed reactor that thermally converts the heavy oils into light gases, liquids and coke. The metals and much of the sulphur are concentrated in the coke. Combustion of the coke provides process heat and the remaining coke is sold or stored on site for later recovery. Syncrude Canada currently operates 3 Fluid Coking units in northern Alberta. Flexicoking extends fluid coking by integrating air gasification to produce a carbon monoxide/hydrogen rich fuel gas that helps meet fuel and energy requirements of bitumen recovery and upgrading. The yields of light gas and liquids are similar to those of the Fluid Coking process. The partial combustion of coke provides the process heat for the thermal conversion and gasification steps. The remaining coke is gasified and desulphurized using Flexsorb technology. At present, there are 5 Flexicoking units in operation around the world. Interest in the technology is growing, particularly in locations with large demand for clean fuel or electricity. It is also suitable for steam assisted gravity drainage (SAGD) operations in Alberta. This presentation outlined the operating principles of the Flexicoking integrated gasification system and compared it with more expensive oxygen gasification processes. tabs., figs.

Volatiles production from the coking of coal; Sekitan no netsubunkai ni okeru kihatsubun seisei

Energy Technology Data Exchange (ETDEWEB)

Yamashita, Y.; Saito, H.; Inaba, A. [National Institute for Resources and Environment, Tsukuba (Japan)

1996-10-28

In order to simplify the coke manufacturing process, a coke production mechanism in coal pyrolysis was discussed. Australian bituminous coal which can produce good coke was used for the discussion. At a temperature raising rate of 50{degree}C per minute, coal weight loss increases monotonously. However, in the case of 3{degree}C, the weight loss reaches a peak at a maximum ultimate temperature of about 550{degree}C. The reaction mechanism varies with the temperature raising rates, and in the case of 50{degree}C per minute, volatiles other than CO2 and propane increased. Weight loss of coal at 3{degree}C per minute was caused mainly by methane production at 550{degree}C or lower. When the temperature is raised to 600{degree}C, tar and CO2 increased, and so did the weight loss. Anisotropy was discerned in almost of all coke particles at 450{degree}C, and the anisotropy became remarkable with increase in the maximum ultimate temperature. Coke and volatiles were produced continuously at a temperature raising rate of 50{degree}C per minute, and at 3{degree}C per minute, the production of the coke and volatiles progressed stepwise as the temperature has risen. 7 refs., 6 figs.

Investigations concerning the mechanism of action of brown-coal coke particles in aerobic biological waste water treatment

International Nuclear Information System (INIS)

Rieger, W.

1990-01-01

At the start of this work experience with the use of brown coal coke in the activated sludge process was lacking entirely. It therefore was necessary to carry through preliminary experiments in order to practically test the effect of Grown-coal coke. In two technical-scale experiments and a pilot test, very good results were obtained with the application of brown-coal coke to activated sludge. These, and previously published results, permitted to evolve moodel concepts of the mechanism of action of coal, especially brown coal coke, in activated sludge. According to these concepts the coal particles act as buffers and a temporary adsorbent of oxygen and waste water constituents. This in turn stimulates the colonization of the surface with microorganisms. In order to corroborate these model concepts, the - adsorption and desorption of solved oxygen to coal in a watery medium and - the effect of coal over a longer period of time were investigated. The results in essence confirm the model concepts. (UWa) [de

Producing metallurgic coke

Energy Technology Data Exchange (ETDEWEB)

Abe, T.; Isida, K.; Vada, Y.

1982-11-18

A mixture of power producing coals with coal briquets of varying composition is proposed for coking in horizontal chamber furnaces. The briquets are produced from petroleum coke, coal fines or semicoke, which make up less than 27 percent of the mixture to be briquetted and coals with a standard coking output of volatile substances and coals with high maximal Gizeler fluidity. The ratio of these coals in the mixture is 0.6 to 2.1 or 18 to 32 percent, respectively. Noncaking or poorly caking coals are used as the power producing coals. The hardness of the obtained coke is DJ15-30 = 90.5 to 92.7 percent.

Process for converting coal into liquid fuel and metallurgical coke

Science.gov (United States)

Wolfe, Richard A.; Im, Chang J.; Wright, Robert E.

1994-01-01

A method of recovering coal liquids and producing metallurgical coke utilizes low ash, low sulfur coal as a parent for a coal char formed by pyrolysis with a volatile content of less than 8%. The char is briquetted and heated in an inert gas over a prescribed heat history to yield a high strength briquette with less than 2% volatile content.

Coking coal of Checua Lenguazaque area; Carbones coquizantes del area Checua - Samaca

Energy Technology Data Exchange (ETDEWEB)

Arboleda Otalora, Carlos Ariel

1987-06-01

In this report a summary of the main characteristics of the coal of the area of Checua-Samaca is presented. Using the main works carried out on this area, the most important geologic, physical-chemical, technological and petrographic aspects are compiled that are considered essential to carry out a technical evaluation of these coal and all the analyses they take to conclude that in this area, bituminous coal are presented with very good coking properties, on the other hand, it is demonstrated by the use that is given to the coal extracted by the small existent mining. However, keeping in mind the demands of the international market of the coking coal, it becomes necessary to improve the existent geologic information to be able to make reliable stratigraphic correlations.

Identification of causes of oil sands coke leachate toxicity

International Nuclear Information System (INIS)

Puttaswamy, N.; Liber, K.

2010-01-01

The potential causes of oil sands coke leachate toxicity were investigated. Chronic 7-day toxicity tests were conducted to demonstrate that oil sands coke leachates (CL) are acutely toxic to Ceriodaphnia dubia (C. dubia). CLs were generated in a laboratory to perform toxicity identification evaluation (TIE) tests in order to investigate the causes of the CL toxicity. The coke was subjected to a 15-day batch leaching process at 5.5 and 9.5 pH values. The leachates were then filtered and used for chemical and toxicological characterization. The 7-day estimates for the C. dubia survival were 6.3 for a pH of 5.5 and 28.7 per cent for the 9.5 CLs. The addition of EDTA significantly improved survival and reproduction in a pH of 5.5 CL, but not in a pH of 9.5 CL. The toxicity of the pH 5.5 CL was removed with a cationic resin treatment. The toxicity of the 9.5 pH LC was removed using an anion resin treatment. Toxicity re-appeared when nickel (Ni) and vanadium (V) were added back to the resin-treated CLs. Results of the study suggested that Ni and V were acting as primary toxicants in the pH 5.5 CL, while V was the primary cause of toxicity in the pH 9.5 CL.

Fine coke production from brown coal (Report on ECSC contract 6220-72/1/102)

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

The possibility of producing a dry brown coal suitable for the production of fine coke and the development of a suitable carbonization process were studied. To prepare the coal it should be screened at 1 mm with the oversize going to fine coke production and the undersize going to briquette production. To increase fine coke production it is necessary to screen the raw smalls less than 2 mm and to pelletize, dry and carbonize them with the coarser constituents. The planning and construction of a hearth oven furnace plant was begun and this is now in operation. A fluidized bed can be used to preheat the coal to improve the oven performance. (In German)

Coking coal consumption of POSCO

International Nuclear Information System (INIS)

Yoo, B.C.

1991-01-01

Pohang Iron and Steel Company Limited (POSCO) was established in 1968. Molten iron was first produced in July 1973 after a 3 year construction period. The long awaited start up of Korea's first integrated steel works provided the momentum for the fast growth of our steel industry. In 1973, the first year of operation, POSCO purchased 770,000 tons of coal from the United States and Australia. The import tonnage was more than doubled in 1976 when we completed the second stage of Pohang Works and has continued to increase reaching 13.1 million tons last year. POSCO's coal consumption will increase one more time next year as the fourth stage of Kwangyang works starts to operate a new blast furnace with an annual molten iron production capacity of 2.8 million tons. Even though the new blast furnace will have the same capacity as the other 3 in Kwangyang, the additional coking coal requirement will be much smaller than the tonnages we needed for the other stages of the works. This paper reports that this is due to the increased use of pulverized coal

Fuel options for oil sands

International Nuclear Information System (INIS)

Wise, T.

2005-01-01

This presentation examined fuel options in relation to oil sands production. Options include steam and hydrogen (H 2 ) for upgrading; natural gas by pipeline; bitumen; petroleum coke; and coal. Various cost drivers were also considered for each of the fuel options. It was noted that natural gas has high energy value but the capital cost is low, and that coke's energy value is very low but the capital cost is high. A chart forecasting energy prices was presented. The disposition of Western Canada's northern gas situation was presented. Issues concerning rail transportation for coal were considered. Environmental concerns were also examined. A chart of typical gas requirements for 75,000 B/D oil sands projects was presented. Issues concerning steam generation with gas and mining cogeneration with gas fuel and steam turbines were discussed, as well as cogeneration and H 2 with gas fuels and steam turbines. Various technology and fuel utility options were examined, along with details of equipment and processes. Boiler technologies were reviewed by type as well as fuel and steam quality and pressure. Charts of cogeneration with gas turbine and circulation fluid bed boilers were presented. Gasification processes were reviewed and a supply cost basis was examined. Cost drivers were ranked according to energy, operating considerations and capital investment. Results indicated that fuel costs were significant for gas and coal. Capital costs and capital recovery charge was most significant with coal and gasification technology. Without capital recovery, cash costs favour the use of bitumen and coke. Gasification would need lower capital and lower capital recovery to compete with direct burning. It was concluded that direct burning of bitumen can compete with natural gas. With price volatility anticipated, dual fuel capability for bitumen and gas has merit. Petroleum coke can be produced or retrieved from stockpiles. Utility supply costs of direct burning of coke is

80. special meeting on coke

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

There were 12 papers presented at the special meeting on coke. These have the following headings: relationship between coal properties and optical anisotropic textures of coke; development of optical texture of chemically modified low rank coal; relationship between fluid and swelling properties of Akabira coal; estimation of coal fluidity; present state and future of robotics; on the thermal stress during the carbonisation process of coals; development of estimation model for coke porosity distribution in the coke oven using X-ray CT; carbonization reaction of coke oven; relationship between qualities of coke and width of coke oven; development of carbonization model in coke ovens - estimation of growing clearance between heating wall and charge; development of automatic transparency analyzer for activated sludge process.

Comparison of the associative structure of two different types of rich coals and their coking properties

Energy Technology Data Exchange (ETDEWEB)

Hengfu Shui; Changhui Lin; Meng Zhang; Zhicai Wang; Mingdong Zheng [Anhui University of Technology, Maanshan (China). School of Chemistry and Chemical Engineering

2010-07-15

Solvent extractions of two different types of Chinese rich coals i.e. Aiweiergou coal (AG) and Zaozhuang coal (ZZ) using the mixed solvent of carbon disulfide/N-methyl-2-pyrrolidinone (CS{sub 2}/NMP) with different mixing ratios were carried out and the caking indexes of the extracted residues were measured. It was found that the extracted residues from the two types of coals showed different changing tendencies of the caking indexes with the extraction yield. When the extraction yield attained about 50% for ZZ coal, the extracted residue had no caking property. However for AG coal, when the extraction yield reached the maximum of 63.5%, the corresponding extracted residue still had considerable caking property with the caking index of 25. This difference indicated the different associative structure of the two coals although they are of the same coalification. Hydro-thermal treatment of the two rich coals gave different extract fractionation distributions for the treated coals compared to those of raw coals respectively. The coking property evaluations of the two coals and their hydro-thermally treated ones were carried out in a crucible coking determination. The results showed that the hydro-thermal treatment could greatly improve the micro-strengths of the resulting coke from the two coals, and the improvement was more significant for the more aggregated AG coal. The reactivities of hydro-thermally treated AG coal blends were almost the same as those of raw coal blends. The higher coke reactivities of AG raw coal and its hydro-thermally treated ones than those of ZZ coal might be attributed to its special ash composition. 20 refs.,4 figs., 5 tabs.

A comparison study on the deoxygenation of coal mine methane over coal gangue and coke under microwave heating conditions

International Nuclear Information System (INIS)

Guo, Xuan; Ren, Jun; Xie, Chuanjin; Lin, Jianying; Li, Zhong

2015-01-01

Highlights: • Microwave has great advantages of energy and time saving in CMM deoxygenation. • Microwave pretreatment results in graphitization of carbonaceous materials. • Coal gangue shows benefit in restricting CH 4 decomposition compared to coke. • Under optimal conditions, there is no residual oxygen and CH 4 is less than 2.2%. - Abstract: Microwave heating has great advantages in saving energy and time; in this study, it has been first successfully applied in the deoxidization process of coal mine methane (CMM), where carbon in coal gangue reacts with oxygen in CMM. Compared with traditional heating, microwave pretreatment resulted in rapid heating of coal gangue in CMM deoxygenation, which was attributable to the graphitization of carbonaceous materials. This prominent advantage of microwave heating can contribute to deoxygenation. In addition, deoxygenation effectiveness for both coke and coal gangue under microwave heating was investigated. It was discovered that coke acted as a catalyst to some extent to accelerate methane decomposition. However, this effect could be greatly restricted when coal gangue was used in the deoxygenation process because of its chemical inertness. Under optimal conditions (650 °C and 300 mL/min), there was no residual oxygen in the outlet gas, and methane loss was less than 2.2%

Influence of thermoplastic properties on coking pressure generation: Part 1 - A study of single coals of various rank

Energy Technology Data Exchange (ETDEWEB)

John J. Duffy; Merrick R. Mahoney; Karen M. Steel [University of Nottingham, Nottingham (United Kingdom). Nottingham Fuel and Energy Centre

2010-07-15

In this study a number of high coking pressure coals with different fluidities were evaluated alongside a number of low pressure coals also with differing fluidities. This was to establish rheological parameters within which a coal may be considered potentially dangerous with regards to coking pressure. The results have confirmed and elaborated on previous findings which show that parallel plate displacement ({Delta}L) and axial force profiles can be used to distinguish between high and low pressure coals, with peak values indicating cell rupture and subsequent pore network formation. This is thought to correspond with plastic layer compaction in the coke oven. For low pressure coals pore coalescence occurs quite early in the softening process when viscosity/elasticity are decreasing and consequently a large degree of contraction/collapse is observed. For higher pressure coals the process is delayed since pore development and consequently wall thinning progress at a slower rate. If or when a pore network is established, a lower degree of contraction/collapse is observed because the event occurs closer to resolidification, where viscosity and elasticity are increasing. For the higher fluidity, high coking pressure coals, a greater degree of swelling is observed prior to cell rupture, and this is considered to be the primary reason for the high coking pressure observed with these coals. An additional consequence of these events is that high pressure coals are likely to contain a higher proportion of closed cells both at and during resolidification, reducing permeability in both the semi-coke and high temperature plastic layers, respectively. Using a rheological mapping approach to follow viscoelastic changes during carbonisation it has been possible to identify specific regions associated with dangerous coals. 76 refs., 11 figs., 3 tabs.

41 CFR 101-26.4904-416 - DD Form 416: Purchase Request for Coal, Coke, or Briquettes.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true DD Form 416: Purchase Request for Coal, Coke, or Briquettes. 101-26.4904-416 Section 101-26.4904-416 Public Contracts and... DD Form 416: Purchase Request for Coal, Coke, or Briquettes. Note: The form illustrated in § 101-26...

Mineral matter reactions in cokes

Energy Technology Data Exchange (ETDEWEB)

D. French; R. Sakurovs; M. Grigore [CSIRO Energy Technology (Australia)

2009-07-15

Some cokes appear to be particularly susceptible to weakening in the blast furnace. A mechanism which has been postulated to explain this is silica reduction by coke. Thus this project was initiated to ascertain the behaviour of quartz and silicates in coke with an emphasis on the role of the clay minerals. It is now possible to obtain quantitative mineralogical data and, the case of coal, to also obtain quantitative data on mineral grain size, shape and association through the use of automated electron beam image analysis techniques. This new ability can allow relationships between the amount of minerals in a coke and its reactivity to be established for the first time. Samples of five Australian coking coals were selected based upon quartz and clay mineral contents, mineral grain size and association. Samples were also provided by BlueScope Steel of coal, feed coke, and tuyere coke samples from the bosh, deadman and raceway regions of the blast furnace. The analytical work program conducted was as follows: Preparation of cokes by CSIRO; Petrography of starting coals and cokes; QEMSCAN of coals; LTA and XRD of starting coals and cokes; Coke reactivity tests (NSC and small scale); Petrography, LTA and XRD of reacted cokes; Petrographic and XRD examination of heat treated cokes. This study indicates that the NSC reactivity test does not adequately reflect the behaviour of coke in the lower part of the blast furnace. Further investigation of the behaviour of coke in the lower part of the blast furnace is required.

Effect of volume change of coal during plastic and resolidifying phase on the internal gas pressure in coke ovens; Sekitan nanka saikoka katei ni okeru taiseki henka ga cokes ro no nanka yoyu sonai gas atsu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Nomura, S; Arima, T [Nippon Steel Corp., Tokyo (Japan)

2000-08-01

The coking pressure in coke oven, which is caused by the internal gas pressure in the coal plastic layer, is determined by the gas permeability of the layer. The gas permeability of the plastic layer depends on its density as well as the physical property of the plastic coal itself The plastic layer is between the coke layer and the coal layer and the effect of the volume change of these outer layers, i.e. contraction and compression, on the density and the internal gas pressure of the plastic layer was studied. Sandwich carbonization test, where different coals were charged in the test coke oven, showed that the internal gas pressure in the plastic layer depends not only on the one kind of coal in plastic phase but also on the other kind of coal in resolidifying phase near the oven walls. The relative volume of coke transformed from the unit volume of coal was measured using X-ray CT scanner and it varied greatly across the coke oven width depending on the kinds of coals. The volume change of coal during plastic and resolidifying phase affects the density and the internal gas pressure of the plastic layer The relative volume of semicoke and coke transformed from the unit volume of coal near the oven walls is higher for a high coking pressure coal than that for a low coking pressure coal. This leads to the high density of the plastic layer and the generation of dangerously high internal gas pressure in the oven centre. (author)

Cooperation with COMECON members in coke chemistry

Energy Technology Data Exchange (ETDEWEB)

Medricky. Z

1987-05-01

Discusses activities of the coking industry division of the standing committee for iron metallurgy of the COMECON. The following cooperation fields are analyzed: raw material basis for coking industry, coal charge preparation and methods for reducing proportion of coking coal in a coal charge (heat treatments, formed coke processes, partial briquetting, pelletizing, increasing coking temperature, packing etc.), coking technology, coke quenching, screening, chemical processing of coal gas, environmental protection in the coking industry, environmental effects of coking, pitch coke production, methods for increasing labor productivity. Research programs coordinated by member countries are reviewed. Programs in which Czechoslovakia participates are discussed.

Research and development in production of special coke types

Energy Technology Data Exchange (ETDEWEB)

Nefedov, P.Ya.; Unterberger, O.G.; Strakhov, V.M. (Vostochnyi Nauchno-Issledovatel' skii Uglekhimicheskii Institut (USSR))

1991-03-01

Discusses methods for increasing quality of foundry coke and quality of special coke types used in non-ferrous metallurgy. Types of coal from various coal basins for production of foundry coke, types of petroleum and coal-derived additives improving caking and coking properties of the standard coal mixtures and effects of partial coal charge briquetting are discussed. Three types of partial coal charge briquetting are comparatively evaluated: continuous coking of the briquetted mixtures of weakly caking lean coal types, anthracites and coking coal mixed with thermosoftening binders; continuous coking of identical mixtures briquetted with non-thermosoftening binders; coking coke dust mixed with thermoreactive binders and briquetted at 200-300 C. Coking conditions, the final coking temperature, binder consumption rates, dimensions of coal briquets, ash content, sulfur content and coke mechanical properties (compression strength and wear) are comparatively evaluated.

Scientific principles underlying the production of metallurgy-grade formed coke from weakly baking coals. Nauchnye osnovy proizvodstva formovannogo metallurgicheskogo koksa iz slabospekayushchikhsya uglei

Energy Technology Data Exchange (ETDEWEB)

Speranskaya, G.V.; Tyutyunnikov, Yu.B.; Erkin, L.I.; Nefedov, P.Ya.; Sheptovitskii, M.S.; Toryanik, E.I.

1987-01-01

Coking coal resources of the USSR are nonuniformly distributed among major coal basins (Donetsk 26%, Pechora 7%, Kizelovsk and L'vov-Volyn' 0.5% each, Kuznetsk 48.2%, Karaganda 7%, South Yakutiya 4.4%, others 7.4%). Only one-third of the resources are available in the European area of the USSR where the demand for blast-furnace coke is greater. The use of weakly baking and nonbaking coals for the production of metallurgy-grade formed coke has been found to be the simplest way to avoid transportation of fat components of coking blends and to cut the cost of pig iron production under Soviet circumstances. Commercial production of the formed coke should enable the blast-furnace coke production to be raised by 15 Mio t/a now and by 20-22 Mio t/a in the nearest future without the structure of the Soviet coal production being significantly affected. The book describes technical properties of the gas, weakly baking and long-flame coals (G, SS and D types, respectively) from Donetsk, Kuznetsk, Irkutsk and Karaganda coal basins used as coking blend components, discusses many scientific and technological aspects of the industrial-scale process (i.e. thermal pretreatment of coal with a gaseous heat-carrier, effect of pressure on the plastic layer formation in weakly baking coal blends, coke oven construction), and reviews technical properties of formed coke (shape and size of coke lumps, drum strength, macro- and microstructure, thermal stability, reactivity) used in the blast-furnace process. 122 refs., 118 figs., 87 tabs.

Statistical summary of coal mining, coking, and briquetting plants and review of the solid fuels market in 1976

Energy Technology Data Exchange (ETDEWEB)

Medaets, J

1977-05-01

This paper reviews the activities of the Belgian coal and coke industry noting that some of the figures are still provisional. Figures are given for production and stocks of coal; personnel; productivity; working hours; salaries; and the production of coke and briquettes.

Significance and development of the utilization of brown coal high temperature coke in the economy of the GDR for the period 1964 to 1974

Energy Technology Data Exchange (ETDEWEB)

Klose, E.; Heschel, W.

1979-01-01

Brown coal high temperature coke production in GDR in the years since 1964 is described. In 1969 the second large brown coal high temperature coking plant, Schwarze Pumpe, went into operation, increasing the total brown coal high temperature coke production to 2 million tons annually. Utilization of the coke size classes in mm from 0-3.15, 3.15-20, 20-31.5, 31.5-45 and greater than 45 mm in the metallurgical, chemical, and energy industries as well as for household heating is shown with figures from 1964, 1970 and 1974. The increasing use of coke in households partly as briquet substitution is also shown (in 1970 42% of the coke was used in households). The substitution of black coal coke by brown coal coke in additional fields of industrial production was also further advanced. Coke production at the Schwarze Pumpe plant is scheduled to increase to 1.6 million tons by 1985 by means of the application of improved coking technologies. Investigations for future industrial solutions to the following coking problems are being conducted: processing coke fines (which make up 10 to 12% of the total produced coke) by briquetting with binders into formed coke, firing coke fines in blast furnaces and power plants, mixed briquetting of coke fines with limestone for carbide production and mixed briquetting of coke and ore fines for metallurgical purposes. (8 refs.) (In German)

The effect of calcination conditions on the graphitizability of novel synthetic and coal-derived cokes

Science.gov (United States)

Bennett, Barbara Ellen

The effects of calcination heating rate and ultimate calcination temperature upon calcined coke and subsequent graphitic material microstructures were studied for materials prepared from three different precursors. The pitch precursors used were Mitsubishi AR pitch (a synthetic, 100% mesophase pitch), the NMP-extracted portion of a raw coal, and the NMP-extracted fraction of a coal liquefaction residue obtained from an HTI pilot plant. These materials were all green-coked under identical conditions. Optical microscopy confirmed that the Mitsubishi coke was very anisotropic and the HTI coke was nearly as anisotropic. The coke produced from the direct coal extract was very isotropic. Crystalline development during calcination heating was verified by high-temperature x-ray diffraction. Experiments were performed to ascertain the effects of varying calcination heating rate and ultimate temperature. It was determined that calcined coke crystallite size increased with increasing temperature for all three materials but was found to be independent of heating rate. The graphene interplanar spacing decreased with increasing temperature for the isotropic NMP-extract material but increased with increasing temperature for the anisotropic materials---Mitsubishi and HTI cokes. Graphene interplanar spacing was also found to be independent of heating rate. Calcined coke real densities were, likewise, found to be independent of heating rate. The anisotropic cokes (Mitsubishi and HTI) exhibited increasing real density with increasing calcination temperature. The NMP-extract coke increased in density up to 1050°C and then suffered a dramatic reduction in real density when heated to 1250°C. This is indicative of puffing. Since there was no corresponding disruption in the crystalline structure, the puffing phenomena was determined to be intercrystalline rather than intracrystalline. After the calcined cokes were graphitized (under identical conditions), the microstructures were re

Young employees of the coking industry for technological progress

Energy Technology Data Exchange (ETDEWEB)

Ladyzhinskii, V.M.; Shul' ga, I.V.

1986-11-01

A conference is reported on technology development in the Soviet coking industry held on December 9-10, 1985 at the Khar'kov Scientific-Research Coal-Chemistry Institute. Representatives of leading research institutes and coking plants delivered 25 papers on the following topics: increasing flotation efficiency by means of new flotation reagents, drum feeders for charging cars, new design of coke oven doors, mathematical models of coal transport to coke ovens, some characteristics of packing coal mixtures in coke ovens, heat treatments of coal mixtures at the Khar'kov experimental coking plant, investigating properties of long-flame and gas coal from the Donbaas used for manufacturing formed coke, modernization of the IGI-DMeTI method for determining properties of coal mixtures for formed coke processes, basic problems associated with environmental protection in formed coke processes, specific problems of coal gasification at 900-1050 C and its effects on coking, evaluating properties of formed coke produced from black coal from the Western Donbass for metallurgy, mixing hot briquets with coal slurries during partial briquetting of the coal charge.

Nitrogen conversion during rapid pyrolysis of coal and petroleum coke in a high-frequency furnace

International Nuclear Information System (INIS)

Yuan, Shuai; Zhou, Zhi-jie; Li, Jun; Wang, Fu-chen

2012-01-01

Highlights: ► Use a high-frequency furnace to study N-conversion during rapid pyrolysis of coal. ► Scarcely reported N-conversion during rapid pyrolysis of petroleum coke was studied. ► Both of NH 3 and HCN can be formed directly from coal during rapid pyrolysis. ► NH 3 –N yields are higher than HCN–N yields in most conditions. ► NH 3 –N yields of petroleum coke increase with temperature and no HCN detected. -- Abstract: Rapid pyrolysis of three typical Chinese coals, lignite from Inner Mongolia, bituminous from Shenfu coalfield, and anthracite from Guizhou, as well as a petroleum coke were carried out in a drop-style high-frequency furnace. The reactor was induction coil heated and had a very small high-temperature zone, which could restrain secondary conversions of nitrogen products. The effects of temperature and coal rank on conversions of fuel-N to primary nitrogen products (char-N, HCN–N, NH 3 –N and (tar + N 2 )–N) have been investigated. The results showed that, the increasing temperature reduced the yields of char-N and promoted the conversion of fuel-N to N 2 . Char-N yields increased, while volatile-N yields decreased as the coal rank increased. In most of the conditions, NH 3 –N yields were higher than HCN–N yields during rapid pyrolysis of coal. In the case of petroleum coke, NH 3 –N yields increased gradually with the increasing temperature, but no HCN was detected. We argue that NH 3 –N can be formed directly through the primary pyrolysis without secondary reactions. Although volatile-N yields of lignite were higher than those of bituminous, yields of (HCN + NH 3 )–N in volatile-N of lignite were lower than those of bituminous. While the (HCN + NH 3 )–N yields of anthracite were the lowest of the three coals. Both of the (HCN + NH 3 )–N yields and (HCN + NH 3 )–N proportions in volatile-N of petroleum coke were lower than the three coals.

Partial briquetting of coal charges as a means of utilizing lower-grade coal for coke making

Energy Technology Data Exchange (ETDEWEB)

Pieters, B.J. (Iscor Limited, Newcastle (South Africa))

1991-08-01

The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briquetted charges, and it was decided to install briquetting plants at the Vanderbijlpark and Newcastle Works. Details are given of the latter plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity. 11 figs., 3 tabs.

Coke retorts

Energy Technology Data Exchange (ETDEWEB)

Jones, S; MacDonald, J D

1916-07-15

To charge vertical coke retorts while preventing escape of gases the coal is fed by a revolving drum to an archimedean screw at the base of the retort, the coke being discharged at the top through a water seal. The feed pockets of the drum which revolves between plates, deliver coal from the hopper to the revolving screw. The coke is forced under the hood to the water seal and is removed by rake conveyor, the gases escaping through the pipe to the main.

On-line determination of moisture in coal and coke

International Nuclear Information System (INIS)

Cutmore, N.G.; Sowerby, B.D.

1987-01-01

The CSIRO Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt% in field tests. CSIRO is developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutrons moisture gauges

Integrated process for synthetic natural gas production from coal and coke-oven gas with high energy efficiency and low emission

International Nuclear Information System (INIS)

Man, Yi; Yang, Siyu; Qian, Yu

2016-01-01

Highlights: • A novel coal and coke-oven gas to SNG (CGtSNG) process is proposed. • Energy efficiency of CGtSNG increases 8% compared to coal-to-SNG process. • CGtSNG reduces 60% CO_2 emission and 72% effluent discharge. • CGtSNG proposes an idea of using redundant coke-oven gas for producing SNG production. - Abstract: There was a rapid development of coal to synthetic natural gas (SNG) projects in the last few years in China. The research from our previous work and some other researchers have found coal based SNG production process has the problems of environmental pollution and emission transfer, including CO_2 emission, effluent discharge, and high energy consumption. This paper proposes a novel co-feed process of coal and coke-oven gas to SNG process by using a dry methane reforming unit to reduce CO_2 emissions, more hydrogen elements are introduced to improve resource efficiency. It is shown that the energy efficiency of the co-feed process increases by 4%, CO_2 emission and effluent discharge is reduced by 60% and 72%, whereas the production cost decreases by 16.7%, in comparison to the conventional coal to SNG process. As coke-oven gas is a waste gas in most of the coking plant, this process also allows to optimize the allocation of resources.

Substitutes for metallurgical coke in pyrometallurgical processes

Energy Technology Data Exchange (ETDEWEB)

Koshkarov, V.Ya.

1982-08-01

A briquetting process using sulphurous petroleum coke and a bituminous binder is described. The characteristics of briquettes made of petroleum coke, blends of coal and petroleum coke, and coal and metallurgical coke are compared. The prospect of replacing 25 to 50% of the metallurgical coke used in lime kilns with non-calcined petroleum coke briquettes is described. (4 refs.)

Thermogravimetric analysis in the characterization of colombian coals used in the production of coke

International Nuclear Information System (INIS)

Guerrero, Camilo; Salamanca, Monica E; Diaz, Jose de J

2010-01-01

Five types of coal from the states of Cundinamarca, Boyaca and Norte de Santander (Colombia) were characterized by proximate, ultimate, rheological, petrographic, calorific and thermogravimetric analysis. The parameters used, especially the ones which determine the rheological properties show that the studied coals and its blends could produce good quality coke. It was observed the inverse relationship between the volatile matter content and the mean vitrinite reflectance, relationship which is attributed to the increase of the aromaticity in the molecular structure of the coal as a consequence of the rank increase. The parameters derived from the thermogravimetric analysis, maximum velocity of de-volatilization and the temperature of maximum velocity of de-volatilization and the media reflectance of the vitrinite showed good correlations. Also was observed an interesting correlation between the velocity of de-volatilization and maximum fluidity. This shows that the thermogravimetric analysis can be a useful tool to characterize in a quick way coals used for metallurgical coke production.

Strength and Compaction Analysis of Sand-Bentonite-Coal Ash Mixes

Science.gov (United States)

Sobti, Jaskiran; Singh, Sanjay Kumar

2017-08-01

This paper deals with the strength and compaction characteristics of sand-bentonite-coal ash mixes prepared by varying percentages of sand, bentonite and coal ash to be used in cutoff walls and as a liner or cover material in landfills. The maximum dry density (MDD) and optimum moisture content (OMC) of sand-bentonite mixes and sand-bentonite-coal ash mixes were determined by conducting the standard proctor test. Also, the strength and stiffness characteristics of soil mixes were furnished using unconfined compressive strength test. The results of the study reveal influence of varying percentages of coal ash and bentonite on the compaction characteristics of the sand-bentonite-coal ash mixes. Also, validation of a statistical analysis of the correlations between maximum dry density (MDD), optimum moisture content (OMC) and Specific Gravity (G) was done using the experimental results. The experimental results obtained for sand-bentonite, sand-bentonite-ash and coal ash-bentonite mixes very well satisfied the statistical relations between MDD, OMC and G with a maximum error in the estimate of MDD being within ±1 kN/m3. The coefficient of determination (R2) ranged from 0.95 to 0.967 in case of sand-bentonite-ash mixes. However, for sand-bentonite mixes, the R2 values are low and varied from 0.48 to 0.56.

Scientific research in the area of coking and coking by-products (based on material from the All-Union Coordinating Conference)

Energy Technology Data Exchange (ETDEWEB)

Rydkevich, M.I.; Tselik, M.P.; Belkina, T.V.

1985-06-01

Subjects covered in the all-union coordinating conference on coking and chemical by-products of coking, which took place on 13-15 July 1984, are discussed. One hundred forty eight on-going and new research themes accepted as research projects for 1985-86 were discussed. Areas of research include coals from the eastern deposits and Pechora basin as raw materials for coking; coals from the southern deposits as coking raw materials; technology of coal preparation for coking; technology for producing blast furnace coke and methods of assessing its quality; technology for producing other kinds of coke and carbon graphite materials; methods for extraction processing and producing chemical products from coking.

Combustion reactivity of chars from copyrolysis of coal with coke-oven gas

Energy Technology Data Exchange (ETDEWEB)

Liao Hongqiang; Sun Chenggong; Li Baoqing [Chinese Academy of Sciences, Taiyuan (China). State Key Lab. of Coal Conversion

1997-12-31

The combustion reactivity of char from pyrolysis of Xianfeng lignite with coke-oven gas (COG) is related to the pyrolysis pressure and heating rate. Decreasing pressure and increasing heating rate enhance the char yields and combustion reactivity. The combustion reactivities of char from coal pyrolysis with COG nearly reach to that of char from hydropyrolysis, but lower than those of char from coal pyrolysis under N{sub 2}. (orig.)

Simulation of blast furnace operation during the substitution of coke and pulverized coal with granulated waste plastic

Directory of Open Access Journals (Sweden)

Kovačević Tihomir M.

2014-01-01

Full Text Available The possibility of using the waste plastic as reducing agent in blast furnace for obtaining pig iron is in focus for the past couple year. The simulation of blast furnace process in BFC software has been performed in order to analyze the coke and coals saving, CO2 emission and determining the economic benefits. Three different batches were made for comparative analysis, depending on the batch composition and input of batch components into the blast furnace: case 1 (C1, case 2 (C2 and case 3 (C3. The base case, C1 contains sinter (bulk material which is needed for obtaining 1 tone of pig iron, quartz which provides slag alkalinity and coke as reducing and energy agent. C2 has the same components as C1, but contains pulverized coal instead one part of coke and C3 contains granulated waste plastic instead coke in an approximately the same amount as pulverized coal. The substitution of coke with pulverized coal and waste plastic is 18.6 % and 25.2 %, respectively. The economic, productivity and ecologic aspects have been analyzed. The consumption of each tone of waste plastic in blast furnace saves 360 $, which is 18 times more than its price, bearing in mind that the market price of coke is 380 $/t % and waste plastic 20 $/t. Regarding the specific productivity, it decreases from 2.13 for C1 to 1.87 for C3. From an environmental aspect there are two main benefits: reduction of CO2 emission and impossibility of dioxin formation. The CO2 emission was 20.18, 19.46 and 17.21 for C1, C2 and C3, respectively.

Effect of hydrothermal treatment of coal on the oxidation susceptibility and electrical resistivity of HTT coke

Energy Technology Data Exchange (ETDEWEB)

Sarkar, N.B.; Sarkar, P.; Choudhury, A. [Central Fuel Research Institute, P.O. FRI, Dhanbad-828108, Jharkhand (India)

2005-02-25

The influence of hydrothermal treatment of coal prior to carbonization, on the oxidation susceptibility of resultant coke/char, calcined at 1350, 1800 and 2200 {sup o}C has been investigated. The non-isothermal thermogravimetric analysis technique has been employed, and parameters such as onset, DTG peak temperatures, and cumulative oxidation loss (wt.%) at different temperatures have been utilized to compare proneness to oxidation with respective untreated samples apart from electrical resistivity. Data suggest that all the cokes/chars samples produced from hydrothermally treated coals are less reactive and more electrically conductive (less resistive) than their respective untreated counterparts. But the extent of improvement of oxidation resistance and electrical conductivity appears to be coal-specific. The kinetic parameters obtained by non-linear regression analysis on multi-curve reveal that the n{sup th} order reaction model (where 'n' was found to vary from 0.9 to 1.3) is the best-fitted model. The higher activation energy values observed for hydrothermally treated coke samples are in agreement with the observation of TG analysis data. Overall results indicate the importance of introducing a hydrothermal treatment step for the improvement of oxidation resistance as well as electrical conductivity of the coke samples.

Floatability characteristics: A case study with three typical Indian prime coking coals

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, D.; Singh, A.K.; Banerjee, P.K. [Tata Steel Ltd., Jamshedpur (India). Division for Research & Development

2008-07-01

Three types of prime coking coals (coals A, B, and C) from Jharia coalfield, India, were investigated for the variations in their floatability characteristics. Among the three coals studied, coal A showed the least floatability. However, its floatability improved to some extent at higher dosages of collector and frother. Other two types of coal, i.e., coals B and C, showed almost similar flotation performance, which was much better as compared to coal A. The studies revealed that coal showed the least floatability characteristics, primarily due to the least concentration of vitrinite and liptinite content and a high percentage of inertinite and mineral matters in the coal. Also, the lower type of vitrinite (V7-V9) was present in the coal in greater proportion as compared to the other two coals and the proportion of ultra fines (-0.053mm) in coal A was higher as compared to the other two coals.

Evaluation of risk strategy and market efficiency in the International coal market: A case study of the Japanese coking coal market

International Nuclear Information System (INIS)

Wang, T.

1992-01-01

Market efficiency and buyers' risk strategy in the Japanese coking import market are examined. The Japanese coal market is found to be inefficient. Japanese buyers traditionally have purchased coals from the United States at a high price and, since the second half of the 1980's, have paid the highest average price to Canadian producers. Given the abundant low cost Australian coals, this purchasing pattern does not meet the cost minimization criteria for efficiency. This is explained mainly by the buyers' risk management strategy. To more accurately examine price differentiation, the complexity of coal quality is considered first. A statistical method is used to estimate comparison of supply regions and a detailed investigation on market conduct is based on quality-adjusted prices, which are assumed to represent the prices of homogeneous coals. Although various reasons are used by researchers to explain Japanese buyers power, this study finds vertical integration of the Japanese companies to be the most important factor creating that power. A detailed survey of vertical integration is made. Finally, a monetary value of the risk premium is estimated by using the partial elasticity of substitution. Total payments by Japanese coking coal buyers for risk premiums are estimated. These represent the extra dollars paid by the Japanese to US and Canadian coal producers for purchasing their coals instead of Australian coals

Impact of co-combustion of petroleum coke and coal on fly ash quality: Case study of a Western Kentucky power plant

International Nuclear Information System (INIS)

Hower, James C.; Thomas, Gerald A.; Mardon, Sarah M.; Trimble, Alan S.

2005-01-01

Petroleum coke has been used as a supplement or replacement for coal in pulverized-fuel combustion. At a 444-MW western Kentucky power station, the combustion of nearly 60% petroleum coke with moderate- to high-sulfur Illinois Basin coal produces fly ash with nearly 50% uncombusted petroleum coke and large amounts of V and Ni when compared to fly ash from strictly pulverized coal burns. Partitioning of the V and Ni, known from other studies to be concentrated in petroleum coke, was noted. However, the distribution of V and Ni does not directly correspond to the amount of uncombusted petroleum coke in the fly ash. Vanadium and Ni are preferentially associated with the finer, higher surface area fly ash fractions captured at lower flue gas temperatures. The presence of uncombusted petroleum coke in the fly ash doubles the amount of ash to be disposed, makes the fly ash unmarketable because of the high C content, and would lead to higher than typical (compared to other fly ashes in the region) concentrations of V and Ni in the fly ash even if the petroleum coke C could be beneficiated from the fly ash. Further studies of co-combustion ashes are necessary in order to understand their behavior in disposal

Alternative coke production from unconventional feedstocks

Energy Technology Data Exchange (ETDEWEB)

Smoot, D.; Eatough, C.N.; Heaton, J.S.; Eatough, S.R.; Miller, A.B. [Combustion Resources, Provo, UT (US)

2004-07-01

This presentation reports on US Department of Energy and company sponsored research and development to develop a technology and process for making metallurgical-quality coke from alternate feedstocks, including by-product and waste carbonaceous materials. The basic patent-pending process blends and presses these carbon-containing materials into briquettes of specified size. This product is referred to as CR Clean Coke because pollutant emission levels are carefully controlled to low levels with little or no vagrant emissions during processing. A wide range of feedstock materials has been investigated in over 600 tests for run-of-mine and waste coal fines of various rank with blends of coal tars and pitches, coal and biomass chars, met-coke breeze or petroleum coke. For various coal/pet-coke/tar feedstocks, CR has produced uniform-sized briquettes in commercial-scale briquettes in three nominal sizes: one inch, two inch, and three inch. These products have been successfully qualified according to stringent requirements for conventional met-coke use in a blast furnace. Several formulation have met and frequently exceeded these established met-coke specifications. One specific product containing coal, tar and pet-coke was selected as a base formulation for which preliminary process design and cost estimates have been completed for construction and operation of a demonstration plant capable of producing 120,000 tons per year of CR Clean Coke. Plant design elements and blast furnace test plans are presented. Tailoring of CR Clean Coke products to other prospective end users including foundry, sugar, soda ash, and ferrometals industries presents additional opportunities. The text is accompanied by 30 slides/overheads. 14 refs., 3 figs., 9 tabs.

REDUCING POWER PRODUCTION COSTS BY UTILIZING PETROLEUM COKE

Energy Technology Data Exchange (ETDEWEB)

Kevin C. Galbreath; Donald L. Toman; Christopher J. Zygarlicke

1999-09-01

Petroleum coke, a byproduct of the petroleum-refining process, is an attractive primary or supplemental fuel for power production primarily because of a progressive and predictable increase in the production volumes of petroleum coke (1, 2). Petroleum coke is most commonly blended with coal in proportions suitable to meet sulfur emission compliance. Petroleum coke is generally less reactive than coal; therefore, the cofiring of petroleum coke with coal typically improves ignition, flame stability, and carbon loss relative to the combustion of petroleum coke alone. Although petroleum coke is a desirable fuel for producing relatively inexpensive electrical power, concerns about the effects of petroleum coke blending on combustion and pollution control processes exist in the coal-fired utility industry (3). The Energy & Environmental Research Center (EERC) completed a 2-year technical assessment of petroleum coke as a supplemental fuel. A survey questionnaire was sent to seven electric utility companies that are currently cofiring coal and petroleum coke in an effort to solicit specific suggestions on research needs and fuel selections. An example of the letter and survey questionnaire is presented in Appendix A. Interest was expressed by most utilities in evaluating the effects of petroleum coke blending on grindability, combustion reactivity, fouling, slagging, and fly ash emissions control. Unexpectedly, concern over corrosion was not expressed by the utilities contacted. Although all seven utilities responded to the question, only two utilities, Northern States Power Company (NSP) and Ameren, sent fuels to the EERC for evaluation. Both utilities sent subbituminous coals from the Power River Basin and petroleum shot coke samples. Petroleum shot coke is produced unintentionally during operational upsets in the petroleum refining process. This report evaluates the effects of petroleum shot coke blending on grindability, fuel reactivity, fouling/slagging, and

Rapid production of metallurgical coke by a pressurized hot-briquetting method. Netsukan kaatsu seikei ni yoru cokes no jinsoku seizo no kokoromi

Energy Technology Data Exchange (ETDEWEB)

Miura, K.; Hayashi, J.; Noguchi, N. (Kyoto University, Kyoto (Japan). Research Laboratory of Carbonaceous Resources Conversion Technology); Hashimoto, K. (Kyoto University, Kyoto (Japan). Faculty of Engineering)

1993-09-20

Rapid production of metallurgical coke from non- and slightly coking coals was studied by pressurized hot-briquetting method. Coal specimens were filled into the mold after pulverizing, and heated at a constant temperature rise rate up to caking temperature under loading pressure to obtain caked coal specimens. Such specimens were then carbonized in nitrogen gas at 800[degree]C. As a result, the coke obtained was superior in compressive strength as compared with commercial cokes, however, its CO2 reactivity was very high requiring heating up to 1,000[degree]C to decrease it, while the reactivity was strongly dependent on coal kind. The optimum processing conditions for slightly coking coal were as follows; loading pressure: 10 [times] 10[sup 5] Pa or more, temperature range under loading pressure: 300-450[degree]C, temperature rise rate: 2-100[degree]C/min, and caking temperature: nearly 500[degree]C. No coke could be produced from coking coals because no volatile matter could be removed from it in a short time under pressure. 13 refs., 8 figs., 1 tab.

Genesis of natural cokes: Some Indian examples

Energy Technology Data Exchange (ETDEWEB)

Singh, Ashok K.; Sharma, Mamta [Central Institute of Mining and Fuel Research, Dhanbad, PIN-828108 (India); Singh, Mahendra P. [Banaras Hindu University, Varanasi, PIN-221005 (India)

2008-06-13

In Indian coalfields huge amounts of natural coke have been produced due to magmatic intrusions. Jharia Coalfield in eastern part of India alone contains approximately 2000 Mt of baked coking coal as a consequence of these intrusions in the form of discordant and concordant bodies. This paper is an effort to investigate the effect of carbonization in two intrusion affected coal seams of Ena (seam XIII) and Alkusa (seam XIV) collieries of Jharia Coalfield. Natural coke is derived from coking coal under in-situ conditions due to intense magmatic induced heat and overburden pressure. Natural coke is characterized by the presence of low volatile matter and high ash contents and organic constituents showing isotropy and anisotropy. Through physical, petrographic and chemical properties of natural coke or 'jhama' as determined by various methods it has been established that the reactives in the unaltered coals (vitrinite, liptinite, pseudovitrinite, reactive semifusinite, etc.) are < 25.0 vol.%, moisture < 2.5%, volatile matter < 15.0% and hydrogen < 4.0%. The temperatures attained in the coal seams have been deciphered using some standard models, which indicate that a temperature {proportional_to} 1000 C was attained. This produced huge amount of anisotropic and deposited carbons. An attempt has been made to understand the factors that influence the genesis of natural coke and heat altered maceral products in coals in Indian coalfields. (author)

Coking industry of China (conclusion of visit to People's Republic of China)

Energy Technology Data Exchange (ETDEWEB)

Sklyar, M.G. (NPO Koksokhimiya (USSR))

1990-12-01

Presents a report on the coking industry in China, in particular, research programs on coking. The report was prepared by Soviet specialists who visited China in March 1990 within the framework of an exchange program. The following aspects are discussed: characteristics of iron metallurgy and the coking industry in China, research institutes that specialize in problems of iron metallurgy and coking, main research programs of Chinese research institutes (development of a 12-category classification of black coal from China, coal preparation prior to coking including selective crushing, formed coke processes, quality of the products of bituminous coal coking, coal gasification and hydrogenation), installations used for research programs in China (delayed coking of black coal, hydrogenation of long-flame coal, coal briquetting), characteristics of selected coking plants in China, training for specialists in the coking industry in China.

Fine art of coking

Energy Technology Data Exchange (ETDEWEB)

Dresner, S.

1984-01-01

The art and science of coking are discussed. Coke is the solid carbon made from the heavy, viscous residue left after the more useful products such as gasoline and diesel fuel have been refined out of the crude oil. Fuel grade coke can be a substitute for steam coal in many applications. Low-sulfur fuel coke is used in blast furnaces for steelmaking. The operations of Conoco's refineries for producing coke is described.

Interactions among different fractions in the thermoplastic state of Goonyella coking coal

Energy Technology Data Exchange (ETDEWEB)

Takahiro Yoshida; Toshimasa Takanohashi; Masashi Iino; Haruo Kumagai; Kenji Kato [National Institute of Advanced Industrial Science and Technology, Tsukuba (Japan)

2004-04-01

Goonyella coking-coal was extracted with a 1:1 (v/v) carbon disulfide/N-methyl-2-pyrrolidinone (CS{sub 2}/NMP) mixed solvent and then fractionated into four with pyridine and chloroform. High-temperature {sup 1}H NMR analysis conducted on each fraction and their mixtures in-situ showed that the lightest, the chloroform-soluble fraction (CS), was rich in mobile hydrogen, H{sub m}, the variation of which with temperature corresponded to that of a thermoplastic parameter tan {delta} determined by in-situ viscoelastic measurement. In contrast, chloroform-insoluble and pyridine-soluble (CIPS) and pyridine-insoluble (PIMS) fractions showed scant change in H{sub m} with temperature, although the intermediate hydrogen, H{sub int}, increased upon heating. These results allow the different fractions to be characterized qualitatively on the basis of differences in hydrogen mobility. In mixtures of the continuous fractions, positive interactions occurred that enhanced the value of tan {delta} as well as the overall hydrogen mobility. A single maximum was observed in the tan {delta} response of these mixtures, which indicated that the heavier fractions were solvated through the action of the lighter ones. In a discontinuous mixture of the fractions, molecular interaction was slight compared to continuous mixtures; only the light fraction started to soften at low temperature and, as a result, a bimodal response occurred in tan {delta}. The thermoplastic response of coking coal can be modeled on a self-dissolution basis involving the {approximately}50% of solvent-soluble components that are present in whole coking coals and which possess a continuous fraction distribution from light to heavy. The mobility of the system develops continuously upon heating as a result of the progressive solvating action of the lighter components facilitating dissolution and/or dispersion of the heavier components. 25 refs., 7 figs., 2 tabs.

A brief introduction to the Tavan Tolgoi coking coal deposit

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

The Tavan Tolgoi coal field is located near the settlement Tsogttsetsii in the South Gobi province, 540 km south of Ulaanbaatar and 96 km east of Dalan Zadgad. The nearest railway stations are Choir, Khar-Airag and Sainshand and are located a distance of about 390 to 450 km, to the northeast of the coal field. An unimproved road connects the property with the railway stations at this time. The Tavan Tolgoi coal field covers 220 square km of land. The coal bearing strata contains 16 coal seams from 3 to 30 m thick with a total average thickness of 165 m. As per the geological survey, the proven and probable reserves of the Tavan Tolgoi coal field are estimated at 5 billion tonnes. Of the 5 billion tonnes, 77.5% or 3.9 billion tonnes are expected to be washed and will produce 2.16 billion tonnes (55% wash recovery) of clean coking coal. 1.41 billion tonnes or 36% of the washed coal will be middlings and available for steam coal, and 9% or 0.33 billion tonnes will be washed or gob. The remaining 1.2 billion tonnes can be mined and sold raw as steam coal. Water, electricity supplies and transportation will have to be developed. Research on this has been done. Markets are envisaged to be within Mongolia, and in the Asia Pacific region. Foreign investment will be needed. 5 figs., 6 tabs.

Split and collectorless flotation to medium coking coal fines for multi-product zero waste concept

Energy Technology Data Exchange (ETDEWEB)

Dey, Shobhana; Bhattacharyya, K.K. [Mineral Processing Division, National Metallurgical Laboratory, Jamshedpur-831007 (India)

2007-06-15

The medium coking coal fines of - 0.5 mm from Jharia coal field were taken for this investigation. The release analysis of the composite coal reveals that yield is very low at 10.0% ash, about 25% at 14% ash and 50% at 17% ash level. The low yield is caused by the presence of high ash finer fraction. The size-wise ash analysis of - 0.5 mm coal indicated that - 0.5 + 0.15 mm fraction contains less ash than - 0.15 mm fraction. Thus, the composite feed was split into - 0.5 + 0.15 mm and - 0.15 mm fractions and subjected to flotation separately. The low ash bearing fraction (- 0.5 + 0.15 mm) was subjected to two stages collectorless flotation to achieve the concentrate with 10% ash. The cleaner concentrate (18.9%) with 10% ash was recovered which has an application in metallurgical industries. The concentrate of 30.2% yield with 12.5% ash could be achieved in one stage collectorless flotation which is suitable for use in coke making as sweetener. As the - 0.15 mm fraction contains relatively high ash, collector aided flotation using sodium silicate was performed to get a concentrate of 23.6% yield with about 17% ash. The blending of this product with cleaner tail obtained from - 0.5 + 0.15 mm produces about 35.0% yield with 17% ash and that can be utilized for coke making. The reject from the two fractions can be used for conventional thermal power plant or cement industries using a 23.5% ash after one stage collector aided flotation and the final tailings produced content ash of 61.6% can be used for fluidization combustion bed (FBC). This eventually leads to complete utilization of coal. (author)

Investigating combined influence of petrology and technological parameters on strength of porous coke body

Energy Technology Data Exchange (ETDEWEB)

Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

1983-09-01

The VUKhIN branch in Kuznetsk investigated effects of coal petrology and coking conditions on structural strength of coke in blast furnaces. Structural strength of coke produced from black coal from the Kuzbass as well as structural strength of coke partially gasified by carbon dioxide under conditions similar to those in blast furnaces was investigated. Fourteen samples of coal mixtures from the Kuzbass were used. Regression analysis was applied. Equations for forecasting coke properties on the basis of coal petrology and selected parameters characterizing coking were derived. Analyses showed that coke structural strength was decisively influenced by coefficients which characterized the average reflectivity of vitrinite in a coal mixture and its average density. After partial coke gasification by carbon dioxide effects of coefficients which characterized coal mixture nonhomogeneity (fluctuations of vitrinite reflectivity) and coal mixture density increased. Increasing coal density partially compensated negative effects of fluctuations of vitrinite reflectivity on coke structural strength. (10 refs.) (In Russian)

Mice housed on coal dust-contaminated sand: A model to evaluate the impacts of coal mining on health

Energy Technology Data Exchange (ETDEWEB)

Caballero-Gallardo, Karina, E-mail: kcaballerog@unicartagena.edu.co; Olivero-Verbel, Jesus, E-mail: joliverov@unicartagena.edu.co

2016-03-01

Coal dust is the most important air pollutant in coal mining in regards to producing deleterious health effects. It permeates the surrounding environment threatening public health. The aim of this study was to evaluate the toxic effects associated with exposure to sand contaminated with coal dust particles below 38 μm in diameter, obtained from a mineral sample collected in the largest coal mine in South America, La Loma, Cesar, Colombia. Sterilized sand was spiked with coal dust to obtain concentrations ranging from zero to 4% coal dust. To model natural exposure, mice were housed for eight weeks in boxes containing this mixture as bedding after which, they were euthanized and blood and tissue samples were collected. Real time PCR analysis revealed an increase in Cyp1A1 mRNA for living on sand with coal dust concentrations greater than 2% compared to mice living on sand without coal dust. Unexpectedly, for mice on coal dust-polluted sand, Sod1, Scd1 and Nqo1 hepatic mRNA were downregulated. The Comet assay in peripheral blood cells and the micronucleus test in blood smears, showed a significant potential genotoxic effect only at the highest coal dust concentration. Histopathological analysis revealed vascular congestion and peribronchial inflammation in the lungs. A dose–response relationship for the presence of hepatic steatosis, vacuolization and nuclei enlargements was observed in the exposed animals. The data suggest living on a soil polluted with coal dust induces molecular, cellular and histopathological changes in mice. Accordingly, the proposed model can be used to identify deleterious effects of exposure to coal dust deposited in soils that may pose health risks for surrounding wildlife populations. - Highlights: • Mice were exposed to coal dust-contaminated sand. • mRNA Markers for PAH exposure, lipid metabolism and oxidative stress increased. • ALT activity in plasma increased at the highest exposure to coal dust. • Liver tissues of exposed

Production of conductive coke for cathodic protection

Energy Technology Data Exchange (ETDEWEB)

Mogollon, E.G.; Henao, L.E.; Pacheco, L.A.; Ortiz, J.L.; Diaz, J.J. [Universidad Nacional de Colombia, Bogota (Colombia). Departamento de Quimica

1999-07-01

The reduction of resistivity of coke by means of the cocarbonization of mixtures of coking coals was studied using coal tar as an additive. Optimum temperature and blending conditions for decreased resistivity were investigated. The effect of particle size on the dependency of coal rank was investigated. 2 refs., 4 figs., 2 tabs.

Coking oven for continuous coke production

Energy Technology Data Exchange (ETDEWEB)

Vabrousek, R

1979-07-15

The coking oven has a vertical rectangular chamber with lateral heating walls to which heat exchangers are attached. The roof from the face of the chamber is a hermetic chute, whose vertical walls are connected to the lateral walls of the chamber and which has the feed conveyor with an unloading and evening device; to the upper wall of which a hermetic loading funnel for coal is attached and a lead-off for gas. The bottom of the chamber consists of segmented locks that are taken up by the hermetic chute. The chute's vertical walls are connected to the vertical walls of the chamber and its horizontal wall has a hermetic unloading funnel with a conveyor for coke removal. Height and width of the chamber are similar to standard chambers; their length reaches 100 to 200 m and longer. Length depends on coke preparation time and speed with which the unloading device can transfer coal. For normal operation, the conveyor belt must function properly in conjunction with the unloading device and segmented locks that form the bottom of the chamber.

Coke

Energy Technology Data Exchange (ETDEWEB)

Trumble, M J

1925-07-02

Coke is obtained from coal, lignite, peat, or wood by heating the material in a retort and distilling off the volatiles by the passage of superheated steam or hot vapors, the hot porous residue being treated with a liquid hydrocarbon and the temperature being so maintained the latter is cracked and carbon deposited on the coke. The vapors or light oils are condensed and the incondensable gases are used as fuel.

Raising lump coke formation capacity of semicoking briquets in the Deuben briquetting plant

Energy Technology Data Exchange (ETDEWEB)

Naundorf, W.; Trommer, D.; Schroeder, H.-W.; Dressler, H.

1988-01-01

Describes brown coal briquetting and coking experiments aimed at producing high quality lumpy coke suitable for heating, metallurgy and other industrial processes. The Deuben coking and gas plant produces low temperature carbonization briquets from coal with 13.2% ash content, 54.8% volatiles, 13.5% semicoking tar with the effect that coke produced from these briquets disintegrates completely into fines (0/15 mm grain size). The study centered on effects of briquetting and coking parameters including coal grain size, coal moisture, briquetting pressure, coking temperature, heating rate and application of sulfite liquor as binder. Graphs of briquetting and coking results are provided. The Deuben coal was shown to be suitable for producing lumpy coke (11.5 to over 20 MPa compression strength) from coal under the optimum briquetting parameters of 0/1 mm grain size, 11% coal moisture, briquetting temperature of 70 to 80 C and briquetting pressure over 120 MPa. Use of a binder was found to be advantageous but not necessary. The produced coke showed favorable combustion properties. 6 refs.

Co, Fe and Ni catalysts supported on coke for direct coal liquefaction

International Nuclear Information System (INIS)

Jimenez, Jose A; Villalba, Oscar A; Rodriguez, Luis I; Hernandez, Orlando; Agamez, Yasmin Y; Dias Jose de Jesus

2008-01-01

Transition metal catalysts supported on coke were prepared by impregnation with a solution of complex of metal-thiourea, that is produced from salt precursors of cobalt chloride, Nickel chloride or iron sulfate and ammonium. sulphide formation on the support surface was generated by decomposition of the metal complex. The catalysts obtained were used in direct coal liquefaction of a medium volatile bituminous coal (Yerbabuena N 1) from Cundinamarca using a 250 Ml, Parr reactor at 723 K and a hydrogen-donor solvent. The catalytic results show, for all samples, both a good coal conversion and an enhancement of the yield of oils, this indicates that the proposed preparation method of catalyst is effective and that eventually the H 2 S sulphidation conventional process could be replaced

Neutron and gamma-ray transmission technique for the on-line determination of moisture in coal and coke

International Nuclear Information System (INIS)

Sowerby, B.D.; Millen, M.J.; Rafter, P.T.

1985-01-01

A fast neutron and gamma-ray transmission technique is being developed for the on-line analysis of moisture in coal and coke. The technique utilises 252 Cf and 137 Cs sources and 3 He and NaI(Tl) detectors. Laboratory measurements on single coal samples have shown that moisture can be determined to better than 1 wt% over the range 0 to 16 wt% moisture and 5 to 17cm thickness. Reduced errors were obtained for restricted ranges of moisture and thickness. Preliminary measurements on coke of thickness 30 to 50cm have shown that moisture can be determined to within 0.26 wt% over the range 1 to 16 wt% moisture

Development of the super coke oven for productivity and environment enhancement toward the 21st century (SCOPE 21); Sekitan kodo tenkan cokes seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Nakashima, Y; Nishioka, K; Otsuka, J [The Japan Iron and Steel Federation, Tokyo (Japan)

1996-09-01

Serious shortage is predicted on cokes for blast furnaces in the first half of the 21st century. In order to deal flexibly with the fluid world market in the future, it is necessary to have a technology developed, by which coals from coking coal to non-coking dust coal can be used. The Japan Iron and Steel Federation and the Center for Coal Utilization, Japan are working on research and development of a new process with enhanced environmentality and economy (SCOPE 21) as a coke manufacturing process to respond to the requirements arisen from the above situation. The process is assessed basing on basic technological seeds such as rapid coal heating and high-speed carbonization and reformation of middle to low temperature cokes. The organizations are moving forward an eight-year development program which has started in fiscal 1994. This paper reports the summary of the development, and results of investigations and researches performed during fiscals 1994 and 1995. Rapid heating tests, middle to low temperature coke reformation tests, and tests for plug transportation of high-temperature coal have been performed. It has been verified, for example, that rapid coal heating can improve coke strength. The development work is being promoted toward grain size distribution and upscaling problems. 5 refs., 16 figs., 2 tabs.

The analysis of coal-and coke ashes by atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Coutinho, C.A.; Prates, H.T.; Pereira, C.P.

1977-01-01

In order to provide better conditions for the control of the chemical composition of the load in the USIMINAS blast furnaces, a method of analysis for sodium, potassium, iron, aluminium, calcium, magnesium and maganese in coal-and coke ash by atomic absorption spectrophotometry was developed. The precision of the calibration curves and the reproducibility of the results are given, together with an estimate of the speed compared with conventional methods of chemical analysis [pt

Mice housed on coal dust-contaminated sand: A model to evaluate the impacts of coal mining on health.

Science.gov (United States)

Caballero-Gallardo, Karina; Olivero-Verbel, Jesus

2016-03-01

Coal dust is the most important air pollutant in coal mining in regards to producing deleterious health effects. It permeates the surrounding environment threatening public health. The aim of this study was to evaluate the toxic effects associated with exposure to sand contaminated with coal dust particles below 38 μm in diameter, obtained from a mineral sample collected in the largest coal mine in South America, La Loma, Cesar, Colombia. Sterilized sand was spiked with coal dust to obtain concentrations ranging from zero to 4% coal dust. To model natural exposure, mice were housed for eight weeks in boxes containing this mixture as bedding after which, they were euthanized and blood and tissue samples were collected. Real time PCR analysis revealed an increase in Cyp1A1 mRNA for living on sand with coal dust concentrations greater than 2% compared to mice living on sand without coal dust. Unexpectedly, for mice on coal dust-polluted sand, Sod1, Scd1 and Nqo1 hepatic mRNA were downregulated. The Comet assay in peripheral blood cells and the micronucleus test in blood smears, showed a significant potential genotoxic effect only at the highest coal dust concentration. Histopathological analysis revealed vascular congestion and peribronchial inflammation in the lungs. A dose-response relationship for the presence of hepatic steatosis, vacuolization and nuclei enlargements was observed in the exposed animals. The data suggest living on a soil polluted with coal dust induces molecular, cellular and histopathological changes in mice. Accordingly, the proposed model can be used to identify deleterious effects of exposure to coal dust deposited in soils that may pose health risks for surrounding wildlife populations. Copyright © 2016 Elsevier Inc. All rights reserved.

Study on the technology of decreasing ash and sulfur in coking coal concentrate by deep-cleaning

Energy Technology Data Exchange (ETDEWEB)

Li, A.; Li, P.; Chen, S. [Hefei Design and Research Institute of Coal Industry, Hefei (China)

2007-06-15

Middling fractions of coking coal, a rare resource in China, were analysed for their embedded minerals both in kind and distribution. Observation with a microscope shows that most are clay minerals of very small particle size. The embedded minerals can be liberated from middling by grinding. Clean coal can be obtained from ground middling by the flocculation-flotation process. The yield of clean coal could thus be increased and its ash and sulfur content decreased. 3 refs., 2 figs., 4 tabs.

Study on the effect of heat treatment and gasification on the carbon structure of coal chars and metallurgical cokes using fourier transform Raman spectroscopy

Energy Technology Data Exchange (ETDEWEB)

S. Dong; P. Alvarez; N. Paterson; D.R. Dugwell; R. Kandiyoti [Imperial College London, London (United Kingdom). Department of Chemical Engineering

2009-03-15

Differences in the development of carbon structures between coal chars and metallurgical cokes during high-temperature reactions have been investigated using Raman spectroscopy. These are important to differentiate between different types of carbons in dust recovered from the top gas of the blast furnace. Coal chars have been prepared from a typical injectant coal under different heat-treatment conditions. These chars reflected the effect of peak temperature, residence time at peak temperature, heating rate and pressure on the evolution of their carbon structures. The independent effect of gasification on the development of the carbon structure of a representative coal char has also been studied. A similar investigation has also been carried out to study the effect of heat-treatment temperature (from 1300 to 2000{sup o}C) and gasification on the carbon structure of a typical metallurgical coke. Two Raman spectral parameters, the intensity ratio of the D band to the G band (I{sub D}/I{sub G}) and the intensity ratio of the valley between D and G bands to the G band (I{sub V}/I{sub G}), have been found useful in assessing changes in carbon structure. An increase in I{sub D}/I{sub G} indicates the growth of basic graphene structural units across the temperature range studied. A decrease in I{sub V}/I{sub G} appears to suggest the elimination of amorphous carbonaceous materials and ordering of the overall carbon structure. The Raman spectral differences observed between coal chars and metallurgical cokes are considered to result from the difference in the time-temperature history between the raw injectant coal and the metallurgical coke and may lay the basis for differentiation between metallurgical coke fines and coal char residues present in the dust carried over the top of the blast furnace. 41 refs., 17 figs., 3 tabs.

Use of coal ash in production of concrete containing contaminated sand

International Nuclear Information System (INIS)

Ezeldin, A.S.

1991-01-01

There are between 2 to 3.5 million underground storage tanks located throughout the nation. Most of these tanks, which store oils and gasolines, are leaking making them one of the primary sources of soil contamination. Adding coal ash or cement to contaminated soil has been used to obtain stationary and inert wastecrete. By using this procedure, stabilization (limiting the solubility and mobility of the contaminants) and solidification (producing a solid waste block) of contaminated soils are successfully achieved. This paper investigates another re-use option of coal ash and contaminated soils. An experimental study evaluating the effectiveness of using coal ash with oil contaminated sand in concrete production is presented. A control mix made of clean sand was designed to yield 500 psi of compressive strength. Sand, artificially contaminated with 3% by weight of motor oil, was used as clean sand replacement. Six concrete mixtures were tested in compression and flexure. The six mixtures were obtained by increasing the ratio of contaminated sand to clean sand, namely; 10%, 20% and 40% and by introducing coal ash to the concrete mixture, namely; 20% of the cement weight. The test results indicate that the inclusion of oil contaminated sand in concrete reduces the compressive and flexural strengths. However, this decrease in strength is compensated by introducing coal ash in the mixture. Regaining that strength offers the possibility of using such concrete as a construction material in special structural applications. More research is required to establish better understanding of that composite and suggest feasible applications

Coal prices rise

International Nuclear Information System (INIS)

McLean, A.

2001-01-01

Coking and semi hard coking coal price agreements had been reached, but, strangely enough, the reaching of common ground on semi soft coking coal, ultra low volatile coal and thermal coal seemed some way off. More of this phenomenon later, but suffice to say that, traditionally, the semi soft and thermal coal prices have fallen into place as soon as the hard, or prime, coking coal prices have been determined. The rise and rise of the popularity of the ultra low volatile coals has seen demand for this type of coal grow almost exponentially. Perhaps one of the most interesting facets of the coking coal settlements announced to date is that the deals appear almost to have been preordained. The extraordinary thing is that the preordination has been at the prescience of the sellers. Traditionally, coking coal price fixing has been the prerogative of the Japanese Steel Mills (JSM) cartel (Nippon, NKK, Kawasaki, Kobe and Sumitomo) who presented a united front to a somewhat disorganised force of predominantly Australian and Canadian sellers. However, by the time JFY 2001 had come round, the rules of the game had changed

Evaluation of pitches and cokes from solvent-extracted coal materials

Energy Technology Data Exchange (ETDEWEB)

McHenry, E.R.

1996-12-01

Three initial coal-extracted (C-E) samples were received from the West Virginia University (WVU) Chemical Engineering Department. Two samples had been hydrogenated to obtain pitches that satisfy Theological requirements. One of the hydrogenated (HC-E) samples had been extracted by toluene to remove ash and higher molecular weight aromatic compounds. We were unable to measure the softening point and viscosity of the non-hydro treated solid extract sample, Positive characteristics in the HC-E materials were softening points of 113-119{degrees}C, low sulfur and ash. The oxygen and nitrogen content of the HC-E samples may limit future usage in premium carbon and graphite products. Coking values were similar to petroleum pitches. Laboratory anode testing indicates that in combination with standard coal-tar pitch, the HC-E material can be used as a binder pitch.

Scientific Council on problems on new processes in the coking industry. [Effect on coke consumption of moisture, sulfur and ash; substitution possibility

Energy Technology Data Exchange (ETDEWEB)

Filippov, B.S.

1981-07-01

This paper presents a report on the Coking Section of the Scientific Council held on November 20, 1980 in Moscow. The following problems were discussed: indexes characterizing blast furnace coke (for furnaces with a volume of 5580 M/sup 3/); replacing metallurgical coke with other types of fuels; use of brown coal; liners of coke ovens. Papers delivered during the session are summarized. Reducing moisture content in blast furnace coke permits its consumption to be reduced by 2%. Reducing sulfur content in blast furnace coke by 0.1% permits its consumption to be reduced from 10 to 15 kg for 1 t of pig iron. Increase in ash content of coke by 1% causes coke consumption increase ranging from 1.5 to 2.0%. About 10 Mmt of coke class with grains above 25 mm in USSR is used for purposes other than blast furnaces. Possibilities of substituting coke with lean coal are evaluated (particularly from Kuzbass). A method for briquetting a mixture of black and brown coal is proposed. Briquets are a suitable fuel in metallurgy. A new type of liner, which consists of at least 92% silicon dioxide, is described. Physical and mechanical properties of the liners are discussed.

Process and apparatus to dry and to preheat coal or coal mixtures and the subsequent coking by the use of non- or weakly baking bituminous coals and/or carbon sources. Verfahren und Vorrichtung zur Trocknung bzw. Vorerhitzung von Kohle oder Kohlemischungen und anschliessender Verkokung unter Verwendung nicht oder nur schwachbackender Steinkohlen und/oder Kohlenstofftraegern

Energy Technology Data Exchange (ETDEWEB)

Echterhoff, J.; Frick, H.; Schaper, A.; Mohmeyer, H.

1982-03-25

A process and an apparatus for the drying and the subsequent coking of non- or weakly baking bituminous coals is described. The coal is compressed by stamping. For preventing the oxidation of the coal grain the coal is kept in contact with an inert medium on the entire path to the coke oven. Water vapor from the coal drying is used as the inert medium.

Coke quality requirements in POSCO

Energy Technology Data Exchange (ETDEWEB)

Song, J.; Yi, J.; Wang, H. [POSCO (Republic of Korea). Cokemaking Dept.

2001-07-01

The 26 overheads describes coke quality requirements in POSCO, Republic of Korea. It is concluded that it is necessary to develop new coal and to prompt technical development in order to produce high quality coke. To improve coke quality. Posco had applied DMAIC (define, measurement, analysis, improvement, control) technique which is part of Six-Sigma activity.

Coliquefaction of coal, tar sand bitumen and plastic (interaction among coal, bitumen and plastic); Sekitan/tar sand bitumen/plastic no kyoekika ni okeru kyozon busshitsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, H.; Okuyama, Y.; Matsubara, K. [NKK Corp., Tokyo (Japan); Kamo, T.; Sato, Y. [National Institute for Resources and Environment, Tsukuba (Japan)

1996-10-28

For the improvement of economy, coliquefaction of coal, tar sand bitumen and plastic was performed under low hydrogen pressure, to investigate the influence of interaction among these on the liquefaction characteristics. For comparison, coliquefaction was also performed under the hydrogen pressure same as the NEDOL process. In addition, for clarifying its reaction mechanism, coliquefaction of dibenzyl and plastic was performed as a model experiment, to illustrate the distribution of products and composition of oil, and to discuss the interaction between dibenzyl and various plastics, and between various plastics. Under direct coal liquefaction conditions, coprocessing of Tanito Harum coal, Athabasca tar sand and plastic was carried out under low hydrogen pressure with an autoclave. The observed value of oil yield was higher than the calculated value based on the values from separate liquefaction of coal and plastic, which suggested the interaction between coal and the mixed plastic. The results of coliquefaction of coal, tar sand bitumen and plastic could be explained from the obtained oil yield and its composition by the coliquefaction of dibenzyl and plastic. 2 refs., 3 tabs.

1170-MW(t) HTGR-PS/C plant application study report: tar sands oil recovery application

International Nuclear Information System (INIS)

Rao, R.; McMain, A.T. Jr.

1981-05-01

This report summarizes a study to apply an 1170-MW(t) high-temperature gas-cooled reactor - process steam/cogeneration (HTGR-PS/C) to tar sands oil recovery and upgrading. The raw product recovered from the sands is a heavy, sour bitumen; upgrading, which involves coking and hydrodesulfurization, produces a synthetic crude (refinable by current technology) and petroleum coke. Steam and electric power are required for the recovery and upgrading process. Proposed and commercial plants would purchase electric power from local utilities and obtain from boilers fired with coal and with by-product fuels produced by the upgrading. This study shows that an HTGR-PS/C represents a more economical source of steam and electric power

Preparation of briquettes on the basis of desintegrated phyto-materials and the admixture of fine-grained coal and coke

Directory of Open Access Journals (Sweden)

Jakabský Štefan

2002-03-01

Full Text Available The contribution deals with the preparation of small-diameter briquettes on the basis of desintegrated phyto-materials and the admixture of coal and coke. The phyto-materials are classified as a dry biomass that can be, on the one hand, the wastes from wood-working industry,(sawdust, chips, bark, etc. or dried mass from the plant production and, on the other hand, the mass of quick-growing plants cultivated on special plantations. In present time this renewable energy resource attracts attention by its heating value ranging from 10 to 16 MJ.kg-1 (EkoWATT, 2001, a low ash content of 0.5 – 6.5 % and by a low sulphur content in a water free sample of 0.05 –0.12 %.As a phyto-material the spruce sawdusts having a grain size of –2 mm were used. The admixture of brown coal, hard coal and coke with a grain size of 0.040 mm was added to the sawdust and in such way prepared mixtures were subjected to briquetting with the aim to obtain small-diameter briquettes. The influence of admixtures amount on the density, and the suitable briquetting press have been studied. A saleability of briquettes on the basis of phyto-materials is conditioned by their density that must be higher than 1,000 kg.m-3. Thus, an adding of denser material with a relatively high calorific value would enable to attain the required density as well as to retain and/or to improve the main utility properties, i.e. calorific value and ash content.The adding evinces itself in an enhancement of briquetting press, but also density of obtained briquettes is often much higher that required by the market. It was showed that in the case of clear spruce sawdust the density of 1,059 kg.m-3 under the briquetting press of 250 MPa can be attained. According to other results, an admixture of brown coal is not very favourable because briquetting press exceeds the value of 300 MPa. As to hard coal adding, the presses under 250 MPa were achieved at the content of 25 – 30 %. The density of these

The effect of high and low dissolved oxygen on the toxicity of oil sands coke and its leachate to Chironomus tentans

International Nuclear Information System (INIS)

Squires, A.J.; Liber, K.

2003-01-01

A study was conducted to assess the effect of low dissolved oxygen on the long-term leaching potential of the toxic constituents found in coke. Coke is one of the waste products produced during the oil sand upgrading process used at Syncrude Canada Ltd. and Suncor Energy Inc. Coke is contaminated by metals and organic compounds which can leach into the environment. In this study, coke from both companies was exposed to reconstituted water and high dissolved oxygen for a period of 30 days, during which time the overlying water containing the leachate and the coke pore-water was chemically analyzed. The benthic macroinvertebrate, Chironomus tentans, was exposed to the aged coke and the overlying leachate after the 30 day period. The study did not reveal any major difference in the survival or growth between the dissolved oxygen treatments or any of the leachate treatments. The macroinvertebrate in the aged Syncrude grew significantly while the Suncor coke strongly inhibited both survival and growth of the macroinvertebrate. The study demonstrates that coke has the potential to negatively affect benthic organisms if it is used uncovered in an aquatic reclamation effort

Blast-furnace coke production in high capacity coke oven batteries from the viewpoint of domestic raw material resources

Energy Technology Data Exchange (ETDEWEB)

Krause, W

1977-05-01

The problem is treated in a complex manner taking into account such technological improvements as: oiling, drying, charge preheating, dry quenching of coke as well as mechanical processing of coke which taken together will give blast furnace coke of the highest quality from domestic coals.

Conceptual design of coke-oven gas assisted coal to olefins process for high energy efficiency and low CO2 emission

International Nuclear Information System (INIS)

Man, Yi; Yang, Siyu; Zhang, Jun; Qian, Yu

2014-01-01

Highlights: • A novel coke-oven gas assisted coal to olefins (GaCTO) process is proposed. • GaCTO has higher energy efficiency and emits less CO 2 compared to coal-to-olefins process. • GaCTO proposes an idea of using redundant coke-oven gas for producing value added products. - Abstract: Olefins are one of the most important platform chemicals. Developing coal-to-olefins (CTO) processes is regarded as one of promising alternatives to oil-to-olefins process. However, CTO suffers from high CO 2 emission due to the high carbon contents of coal. In China, there is 7 × 10 10 m 3 coke-oven gas (COG) produced in coke plants annually. However, most of the hydrogen-rich COG is utilized as fuel or discharged directly into the air. Such situation is a waste of precious hydrogen resource and serious economic loss, which causes serious environmental pollution either. This paper proposes a novel co-feed process of COG assist CTO in which CH 4 of COG reacts with CO 2 in a Dry Methane Reforming unit to reduce emissions, while the Steam Methane Reforming unit produces H 2 -rich syngas. H 2 of COG can adjust the H/C ratio of syngas. The analysis shows that the energy efficiency of the co-feed process increases about 10%, while at the same time, life cycle carbon footprint is reduced by around 85% in comparison to the conventional CTO process. The economic sustainability of the co-feed process will be reached when the carbon tax would be higher than 150 CNY/t CO 2

Certification of the contents (mass fraction) of carbon, hydrogen, nitrogen, chlorine, arsenic, cadmium, manganese, mercury, lead, selenium, vanadium and zinc in three coals. Gas coal CRM No. 180; Coking coal CRM No. 181; Steam coal CRM No. 182

Energy Technology Data Exchange (ETDEWEB)

Griepink, B; Colinet, E; Wilkinson, H C

1986-01-01

The report first describes the preparation of three coal reference materials: Gas coal (BCR No. 180), Coking coal (BCR No. 181) and Steam coal (BCR No. 182). It deals further with the homogeneity and stability tests for major, minor and trace components. The contents (mass fractions) of the elements: C, H, N, Cl, As, Cd, Mn, Hg, Pb, Se, V and Zn are certified. The analytical techniques used in the certification are summarised. All the individual results are given and recommendations for analysis are made.

Consumption of fuels and energy in the coking industry and ways of reducing consumption

Energy Technology Data Exchange (ETDEWEB)

Vasil' ev, Yu.S.; Tsel' ik, M.P.; Belkina, T.V. (Khar' kovskii Nauchno-Issledovatel' skii Uglekhimicheski Institut (USSR))

1989-08-01

Coking plants in the USSR consume 4,000 million kWh electric energy, 100 million GJ heat energy and 35,000 million m{sup 3} gaseous fuels per year. Structure of energy consumption is the following: 68% gaseous fuels, 24% steam and 8% electric energy. Processes of coal preparation, crushing, mixing, coking and quenching are analyzed from the point of view of energy consumption. The following methods for reducing energy consumption are discussed: using the FM-25 flotation machines for flotation of coking coal slurries, briquetting the whole coal charge for coking, optimization of air supply rates for combustion of gases used for coke oven heating, use of control systems for coke oven heating considering coal charge density, waste heat utilization from quenching. 4 refs.

Price negotiation of coal to be loaded in 1989

Energy Technology Data Exchange (ETDEWEB)

Senmura, Akira (Institute of Energy Economics, Tokyo (Japan))

1989-06-01

The Institute of Energy Economics summarized the negotiated prices for coals to be loaded in 1989 for coke making coal and non coking coal. In order to suppress the price increase of coke making coal as low as possible, five iron making companies where Nippon Steel and Kawasaki Steel are the center, started to negotiate from US showing lower markup requirement and decided to increase the price from $1.65 to $2. They agreed to increase the price for Australian coal as follows: $3.5 for coke making coal, $5.5 for slightly coking coal, $4.5 for weakly coking coal and further they contracted with $3.5 markup and $3.5 markup for China and USSR coals from December, 1988 to March, 1989. The negotiation for non coking coal started from USSR similarly and agreed with $3 markup for USSR coal, $5.3 markup for South African coal, and $3.5 markup for Australian coal but the negotiation is performing to China coal on Australian basis. The Australian share for non coking coal is higher, that is, 70% and therefore Japanese power generating companies are promoting to import non coking coal from US for the competition. 5 tabs.

Emission and source characterization of monoaromatic hydrocarbons from coke production

Energy Technology Data Exchange (ETDEWEB)

He, Q.S.; Wang, X.M.; Sheng, G.Y.; Fu, J.M. [Chinese Academy of Sciences, Guangzhou (China). State Key Laboratory of Organic Geochemistry

2005-09-15

Monoaromatic hydrocarbons (MAHs) from indigenous and industrial coking processes are studied in Shanxi province. They are sampled on the top of coke ovens and in the chimneys using stainless steel canister and determined by GC/MSD after preconcentration with liquid nitrogen. Benzene, toluene and xylene are the main components among MAHs emitted from coking processes. Benzene and the total MAHs concentrations were as high as 3421.0 microg/m3 and 4 865.9 microg/m3 in the air from indigenous coking, 548.7 microg/m3 and 1 054.8 microg/m3 in the oventop air from industrial coking, and 1 376.4 microg/m3 and 1 819.4 microg/m3 in stack gas from industrial coking, respectively. The MAHs concentrations vary greatly during the indigenous coking process, which in the prophase (from firing to 10 days) is obviously higher than in the anaphase (10 days to quenching the coke). In industrial coking the MAHs in the oventop air are highest when charging the coal and next when transferring the hot coke, but in stack gas they are highest when charging coal and lowest when transferring the coke. Benzene, toluene, ethylbenzene and xylene (BTEX) in industrial coking samples show good linearity, indicating that MAHs in industrial coking might come predominantly from coal pyrolysis; but BTEX distribute dispersedly in indigenous coking samples, indicating that its emission might be affected by many factors. In all samples BTEX ratios especially high B/E ratio, is unique among MAHs sources, and might be helpful to characterize pollution from coking.

[Emission and source characterization of monoaromatic hydrocarbons from coke production].

Science.gov (United States)

He, Qiu-Sheng; Wang, Xin-Ming; Sheng, Guo-Ying; Fu, Jia-Mo

2005-09-01

Monoaromatic hydrocarbons (MAHs) from indigenous and industrial coking processes are studied in Shanxi province. They are sampled on the top of coke ovens and in the chimneys using stainless steel canister and determined by GC/MSD after preconcentration with liquid nitrogen. Benzene, toluene and xylene are the main components among MAHs emitted from coking processes. Benzene and the total MAHs concentrations were as high as 3421.0 microg/m3 and 4 865.9 microg/m3 in the air from indigenous coking, 548.7 microg/m3 and 1 054.8 microg/m3 in the oventop air from industrial coking, and 1 376.4 microg/m3 and 1 819.4 microg/m3 in stack gas from industrial coking, respectively. The MAHs concentrations vary greatly during the indigenous coking process, which in the prophase (from firing to 10 days) is obviously higher than in the anaphase (10 days to quenching the coke). In industrial coking the MAHs in the oventop air are highest when charging the coal and next when transferring the hot coke, but in stack gas they are highest when charging coal and lowest when transferring the coke. Benzene, toluene, ethylbenzene and xylene (BTEX) in industrial coking samples show good linearity, indicating that MAHs in industrial coking might come predominantly from coal pyrolysis; but BTEX distribute dispersedly in indigenous coking samples, indicating that its emission might be affected by many factors. In all samples BTEX ratios especially high B/E ratio, is unique among MAHs sources, and might be helpful to characterize pollution from coking.

Coal marketing manual 1987

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

This manual provides information on the international coal market in tabulated format. Statistics are presented for the Australian coal industry, exports, currency movements, world coal production, coal and coke imports and exports. Detailed information is provided on the Australian coal industry including mine specific summaries. Pricing summaries for thermal and coking coal in 1987, coal quality standards and specifications, trends in coal prices and stocks. Imports and exports for World coal and coke, details of shipping, international ports and iron and steel production. An exporters index of Australian and overseas companies with industry and government contacts is included. 15 figs., 67 tabs.

Precautionary measures in determining volatile matter in natural coke washability fractions

Energy Technology Data Exchange (ETDEWEB)

Ashok K. Singh; N.K. Shukla; S.K. Srivastava; D.D. Haldar; B.N. Roy; Mamta Sharma [Central Institute of Mining and Fuel Research, Dhanbad (India)

2009-01-15

Industrial utilization of heat-altered coal, especially natural coke derived from coking coal, has become a challenge. As such approximately 3,500 million tones (Mt) reserves of baked coals are available in different coalfields of India. In the present investigation, a natural coke sample (03 tone) was collected from a huge dump of seam XIV of Burragarh colliery under leasehold of Bharat Coking Coal Ltd., a subsidiary of Coal India Ltd., situated in Dhanbad district of Jharkhand state. It was observed that the volatile matter in the washability fractions of different size ranges (50 to 0.5 mm) at specific gravity 1.40 to 1.80 showed erratic distribution with respect to ash. To check the abnormality, the subsamples were subjected to microscopic (petrographic) study and chemical analysis including CO{sub 2} determination. The high concentration of CO{sub 2} is related to high concentration of carbonate minerals generated due to igneous intrusions in coal seams. Based on above observations, it was concluded that the volatile matter can be corrected through determined CO{sub 2} content in each fraction. Since efforts are being made to use natural coke in different industries such as steel, power, cement, carbon artifacts, etc., a careful investigation of volatile matter distribution in natural coke washability fractions would be of immense help in planning its bulk use.

Problems of new processes in coking industry discussed at the Scientific Council of the GKNT and the Section of Coking Industry of the Scientific and Technological Council of the Ministry of Iron and Steel Industry of the USSR

Energy Technology Data Exchange (ETDEWEB)

Ermolova, V.P.

1983-03-01

A report is given from the conference on new processes in the Soviet coking industry held in Moscow on 28-29 October 1982. The following papers were delivered: implementing research programs on new coking processes, new trends in coking plant design and construction in the 11th 5 year plan and in the time period until 1990, increasing efficiency of coking industry, research program of the Scientific Council in 1983. The report concentrates on new trends in coking plant design. Considering that the raw material basis of the Eastern regions of the USSR is poor in high quality coking coal the new coking processes and technologies should use weakly coking coal. The following schemes are discussed: heat treatments (especially useful in the case of black coal from the Kuzbass characterized by intensive fluctuations of petrology), selective crushing (schemes developed by the VUKhIN Institute), partial briquetting of coal mixtures (experiments carried out by the UKhIN in the Donbass in 1982). Other problems of coking such as development of new systems of smokeless fuel feeding to coke ovens, dry coke quenching, increasing capacity of coke chambers to 41.6 m/sup 3/, environmental protection in coking industry and production of special coke types from poor quality coal for metallurgy are also described.

Fissure formation in coke. 3: Coke size distribution and statistical analysis

Energy Technology Data Exchange (ETDEWEB)

D.R. Jenkins; D.E. Shaw; M.R. Mahoney [CSIRO, North Ryde, NSW (Australia). Mathematical and Information Sciences

2010-07-15

A model of coke stabilization, based on a fundamental model of fissuring during carbonisation is used to demonstrate the applicability of the fissuring model to actual coke size distributions. The results indicate that the degree of stabilization is important in determining the size distribution. A modified form of the Weibull distribution is shown to provide a better representation of the whole coke size distribution compared to the Rosin-Rammler distribution, which is generally only fitted to the lump coke. A statistical analysis of a large number of experiments in a pilot scale coke oven shows reasonably good prediction of the coke mean size, based on parameters related to blend rank, amount of low rank coal, fluidity and ash. However, the prediction of measures of the spread of the size distribution is more problematic. The fissuring model, the size distribution representation and the statistical analysis together provide a comprehensive capability for understanding and predicting the mean size and distribution of coke lumps produced during carbonisation. 12 refs., 16 figs., 4 tabs.

Comparative study of the performance of conventional and column flotation when treating coking coal fines

Energy Technology Data Exchange (ETDEWEB)

Jena, M.S.; Biswal, S.K.; Das, S.P.; Reddy, P.S.R. [Institute of Minerals and Materials Technology (CSIR), Bhubaneswar - 751 013 (India)

2008-12-15

Investigations were carried out on coking coal fines by conventional cell and column flotation techniques. The effects of different operating parameters were evaluated for both conventional and column flotation. The coal fines were collected from Bhojudih washery, India. These coal fines averaged 24.4% ash, 19.8% volatile matter and 53.8% fixed carbon on a dry basis. A commercial grade sodium silicate, light diesel oil and pine oil were used as depressant, collector and frother respectively. The flotation performance was compared with release analysis. The conventional flotation results indicated that a clean coal with 14.4% ash could be obtained at 78.0% yield with 88.4% combustible recovery. The ash of the clean coal could be further reduced to 10.1% at 72.0% yield with 85.6% combustible recovery by using column flotation. The column flotation results were close to those obtained by release analysis. (author)

Coal statistics 1977

Energy Technology Data Exchange (ETDEWEB)

Statistical Office of the European Communities

1978-01-01

Presents tables of data relating to the coal market in the European Community in 1977. The tables cover hard coal production, supply and trade; briquettes; cokes; lignite, brown coal briquettes and peat; and mines and coke ovens.

Materials for making coke

Energy Technology Data Exchange (ETDEWEB)

Kern, L

1936-08-19

In the preparation of carbonized fuel briquettes, material such as bituminous, lignitic, or anthracitic coal, slack, waste or shale is treated with an electropositive solution such as hydrochloric acid or an acidic chloride to bring ash-forming constituents into colloidal form. The mixture is pressed with a colloid precipitating electro-negative solution such as sodium hydroxide, and moulded, the product being heated in the absence of air and coked. In an example bituminous coal is ground and then masticated with dilute hydrochloric acid. Some dilute manganese chloride is added followed by a solution of sodium hydroxide which precipitates the metals and silica as colloidal gels while the mixture is thoroughly agitated. The plastic mass is briquetted and dried at about 125/sup 0/C and then coked in vertical ovens at 700/sup 0/C. Chlorides recovered with the distillate gases may be utilized as solvent instead of hydrochloric acid. If the coal contains a large amount of sulfur acidified manganese chloride including a large proportion of iron is used as colloid forming material, the oxides of manganese and iron subsequently precipitated forming stable compounds with the non-volatile sulfur on coking or combustion.

Microstructural characteristics of toluene and quinoline-insolubles from coal-tar pitch and their cokes

Energy Technology Data Exchange (ETDEWEB)

Panaitescu, C. [University POLITEHNICA Bucharest, Faculty of Industrial Chemistry, Fuel Laboratory, Polizu St. 1, Sector 1, 011061, Bucharest (Romania); Predeanu, G. [Metallurgical Research Institute, Department of Raw Materials, Mehadia St. 39, Sector 6, 060543 Bucharest (Romania)

2007-08-01

The structural composition of coal-tar pitch used in the preparation of the special binder-pitch, was determined with special emphasis on the optical properties of the {beta}-resins, as typical components necessary to obtain electrodes of best quality through the pyrogenetic processes of baking and graphitization. In addition to raw toluene- and quinoline-insolubles (TI, QI), the corresponding cokes were analysed to evaluate, by structural composition and microtexture, the behaviour of pitch fractions during carbonization. The results suggest the dependence of the texture development on the type of toluene- and quinoline-insolubles and {beta}-resins during processing conditions, which influence the mesophase formation. An original and important result of the carbopetrographical study is represented by the identification and evaluation of {beta}-resins in the coke texture. (author)

Review of a Proposed Quarterly Coal Publication

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This Review of a Proposed Quartery Coal Publication contains findings and recommendations regarding the content of a new summary Energy Information Administration (EIA) coal and coke publication entitled The Quarterly Coal Review (QCR). It is divided into five sections: results of interviews with selected EIA data users; identification of major functions of the coal and coke industries; analysis of coal and coke data collection activities; evaluation of issues conerning data presentation including recommendations for the content of the proposed QCR; and comparison of the proposed QCR with other EIA publications. Major findings and recommendations are as follows: (1) User interviews indicate a definite need for a compehensive publication that would support analyses and examine economic, supply and demand trends in the coal industry; (2) the organization of the publication should reflect the natural order of activities of the coal and coke industries. Based on an analysis of the industries, these functions are: production, stocks, imports, exports, distribution, and consumption; (3) current EIA coal and coke surveys collect sufficient data to provide a summary of the coal and coke industries on a quarterly basis; (4) coal and coke data should be presented separately. Coke data could be presented as an appendix; (5) three geographic aggregations are recommended in the QCR. These are: US total, coal producing districts, and state; (6) coal consumption data should be consolidated into four major consumer categories: electric utilities, coke plants, other industrial, and residential commercial; (7) several EIA publications could be eliminated by the proposed QCR.

Proceedings of the Joint Meeting of The Fuel Society of Japan (1991). 28th Coal Science Conference/91st Coke Meeting; (Sha) nenryo kyokai godo taikai happyo ronbunshu (1991). Dai 28 kai sekitan kagaku kaigi dai 91 kai cokes tokubetsukai

Energy Technology Data Exchange (ETDEWEB)

1991-11-07

Relating to coke, studies are made on the rapid coke production method, oven investigation during carbonization, and operational management/control. As to coal science, studies are mainly on the brown coal two-stage liquefaction (BCL) method, and data on the pilot plant and PSU are reported. Concerning bituminous coal liquefaction, PSU data mostly including the NEDOL process, and characteristics of liquefaction residue and its effective utilization by thermal decomposition are reported. Regarding the liquefaction mechanism, an experimentally extensive study on catalyst, solvent and reaction conditions is made using model materials and coal itself on the bench scale and also in the pilot plant. Engineering subjects on residue, solvent deashing, scale attachment and coprocessing are also reported. Relations of decomposition process to coal chemical structure changes and reaction conditions are investigated. As to coal gasification, studies, which are not many, are conducted on material balance, heat balance, and image characteristics of char for gasification and factors controlling reactivity.

Fast-neutron and gamma-ray transmission technique for the on-line determination of moisture in coal and coke

International Nuclear Information System (INIS)

Sowerby, B.D.; Millen, M.J.; Rafter, P.T.

1988-01-01

A fast neutron and γ-ray transmission technique is being developed for the on-line analysis of moisture. Calculations show that the technique is capable of determining coke moisture to better than 0.2 wt% over a wide range of coke thicknesses. The favoured technique uses a thick Li-glass detector surrounded by a neutron moderator to determine simultaneously the fast neutron and γ-ray intensities. Laboratory measurements on single coke samples showed that moisture can be determined to within 0.2 wt% over the range 3-13 wt% moisture and 300-500 mm thickness. Measurements on a range of coke samples showed that the increase in r.m.s. error due to bound H variations is less than about 0.4 wt% moisture. Applications of the technique, to moisture determination in black and brown coal are also investigated, both by calculation and experiment. Further potential applications of the technique are discussed, including the determination of C in steel. (author)

Utilization coke dust as fuel in the cement industry

International Nuclear Information System (INIS)

Nawaz, S.

2006-01-01

Utilization of coke dust available from coal carbonization plants, as a fuel in the cement industry has been undertaken and discussed in this research paper. The parameters studied include physical and chemical evaluation of the coke dust and its economic feasibility/ suitability as fuel for the cement plants. Detailed studies have been carried out on the above referred parameters. In addition a comparative study has been done to access its suitability in comparison to other fuels especially imported coal. It has been found that the coke dust contained about 66% fixed carbon, 29% ash, 4% volatile matter, 1% moisture and 0.48% sulphur. It gross calorific value was found to be 5292 Kcal/kg. The detailed analysis of coke dust ash was also performed to determine as to how its constituents will compare with the cement constituents. Keeping in view the experimental results/ data generated on the coke dust, it has been concluded that it can be quite a good substitute for imported coal. In doing so a substantial financial saving can be achieved which ranges 40-45%. (author)

Coke breakage behaviour in relation to its structure

Energy Technology Data Exchange (ETDEWEB)

Peirce, T J; Horton, A E; Tucker, J

1980-06-14

The relationship between coke macrostructure and volumetric (coarse) breakage behaviour, and the manner in which both features are affected by the coal charge composition are discussed. Coke pieces which are extensively fissured fail spontaneously after only a few revolutions in the drum; coke pieces which are less fissured require an extended treatment in the drum and finally fail in a manner consistent with that of fatigue crack growth induced by repeated impact. This heterogeneity in breakage behaviour was demonstrated in terms of an abrupt change in gradient of the Weibull distribution function for the coke. Heterogeneity may be removed by fully stabilising the coke or by the use of a more energetic test method. The role of fatigue crack growth in coke breakage was studied by cutting fissures of defined depth in full stabilised coke and assessing the rate of crack growth as a function of fissure depth and fracture toughness. The form of the results was consistent with that given by the Paris-Erdogan law and the rate of crack growth (for a given stress intensity level) was shown to increase with reducing coke toughness. Explanations are suggested to account for the role of blend additives in modifying the fissured properties and fracture toughness of coke made from high-volatile coal.

Giprokoks proposals for improvement in air quality at coke battery 1A of Radlin coke plant

Energy Technology Data Exchange (ETDEWEB)

T.F. Trembach; A.G. Klimenko [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

2009-07-15

Coke battery 1A, which uses rammed batch, has gone into production at Radlin coke plant (Poland), on the basis of Giprokoks designs. Up-to-date dust-trapping methods are used for the first time within the aspiration systems in the coal-preparation shop and in improving dust collection within the production buildings.

Influence of thermal charge preparation on coke comminution under blast-furnace operating conditions

Energy Technology Data Exchange (ETDEWEB)

Shkoller, M.B.; Dinel' t, V.M.; Korchuganova, G.S.; Petrov, V.B.

1983-09-01

Reactions of coke in the blast furnace are determined mainly by the nature of the coke itself which depends on the coal properties, its preparation and the coking conditions. In the blast furnace the coke reacts with alkali and alkaline earth metals in the burden. Preheated coal charges were found to absorb far less sodium and potassium carbonates than a conventional moist charge over an equivalent period, due to the smaller pore volume available.

Making coke

Energy Technology Data Exchange (ETDEWEB)

Wodehouse-Temple, C G

1929-07-12

Semi-coke is produced by mixing low-value absorbent solid carbonaceous material such as coal dust, slack, gas-works coke, lignite, torbanite, raphilite, cannel, or shale with not more than 20% of a carbonaceous binding material such as petroleum distillation residue, tarry residues, pitch bitumen, Trinidad asphalt, Manjak or the substance known under the registered Trade Mark Gilsonite and subjecting the mixture without briquetting to a temperature not exceeding 550/sup 0/C. According to the first Provisional Specification, the mixture may if desired be briquetted before being heated and the second constituent may be present to the extent of 30%.

Results of tuyere coke sampling with regard to application of appropriate coke strength after reaction (CSR for a blast furnace

Directory of Open Access Journals (Sweden)

Shiau J-S.

2017-01-01

Full Text Available Raising pulverized coal injection (PCI will decrease coke rate, but increase the residence time of coke and abrasion in the blast furnace (BF. Thus, insufficient coke strength will generate more coke fines in the lower BF and result in lower permeability and production of hot metal (HM. For understanding the behavior of coke at various HM productivities, a tuyere coke sampler was used to collect the coke samples for measuring the coke strength. Firstly, the difference of sampled coke under the conditions of various HM productivities was explored. Secondly, the BF operating conditions and causes of generating more coke fines was correlated by testing the coke reaction rate after reaction. Finally, according to the above analysis results, the relative regression equations had been obtained for sampling coke properties, BF operation conditions and BF permeability. Furthermore, the coke strength after reaction (CSR quantitative target and its online system at various blast conditions were set to provide some reference for coke and HM production.

Dependence of microhardness of coke on carbon content and final coking temperature

Energy Technology Data Exchange (ETDEWEB)

Kaloc, M.; Dvorak, P.

1995-12-31

At present time is important the coke-quality, tested by various methods again. The new methods of evaluation of coke quality as e.g. CSR, CRI, ACRI etc. demonstrate, that the mechanical stability parameters are in connection of microstructure of coke mass. The purpose of present paper is to investigate the dependence of microhardness on the carbon content and the final carbonisation temperature in the coal-coke series. The samples prepared experimentally in more series from different coal blends from 20{degrees}C to 1100{degrees}C were investigated both mega- and microscopically. The tests of microhardness are based on the use of the Hanemann microhardness tester. Principally this method consists in impressing the diamond pyramid into the surface of the sample. The data on the pressure applied are subtracted on the scale of load. An important factor influencing the results is the choice of the points from which the sample is to be withdrawn. The choice is dependent on the aim to be achieved. For the determination of an average microhardness it is sufficient to take sample from the middle part of the coke block representing the half width of the coking chamber. The choice of the point is also of great importance. In strong and homogeneous walls, sharply bounded, impressions can be found with a distinct diagonal cross. In thin walls the impressions are distinguished by distinct boundaries, the middle part, however, not being distinct as the pyramidal point did not penetrate the wall. Impressions providing accurate values are those distinctly bounded by a distinct diagonal cross. The walls not having been chosen correctly, the errors reveal themselves as the scattering of the points in the diagrams of microhardness.

In the coking section of the Scientific Council of the Main Committee for Science and Technology 'New processes in ferrous metallurgy'

Energy Technology Data Exchange (ETDEWEB)

Bukvareva, O.F.

1989-12-01

Reports on a meeting held in June 1990 in Khar'kov on new technologies of black coal coking and methods for coal gas purification used in the USSR and other countries. The following problems associated with economic analysis of new coking technologies were analyzed: types of coal used in mixtures for coking, mixtures for coking, coal mixture preheating, partial briquetting. The following problems associated with coal gas purification were discussed: primary cooling systems, methods for ammonia separation from coal gas, coal gas desulfurization, separation of hydrogen cyanide, amine methods for desulfurization. Recommendations for research programs on new coking technologies and on coal gas purification are discussed.

Study of the raw material base for a by-product coke plant by the method of thermal degradation of coal in a centrifugal field

Energy Technology Data Exchange (ETDEWEB)

Epimakhov, N.M.; Kardashova, V.F.; Sulimova, E.I.

1982-01-01

Coals from the Donbass and Karaganda basins, being supplied to a Bagley by-product coke plant were studied. A sharp distinction between coals of different degrees of metamorphism in respect to the yield of liquid nonvolatile products was demonstrated. A difference in respect to this index was recognized for individual coals from one and the same technological group from a single basin.

Coal background paper. Coal demand

International Nuclear Information System (INIS)

1997-01-01

Statistical data are presented on coal demands in IEA and OECD member countries and in other countries. Coal coaking and coaking coal consumption data are tabulated, and IEA secretariat's coal demand projections are summarized. Coal supply and production data by countries are given. Finally, coal trade data are presented, broken down for hard coal, steam coal, coking coal (imports and export). (R.P.)

Effects of Two-stage Heat Treatment on Delayed Coke and Study of Their Surface Texture Characteristics

Science.gov (United States)

Im, Ui-Su; Kim, Jiyoung; Lee, Seon Ho; Lee, Byung-Rok; Peck, Dong-Hyun; Jung, Doo-Hwan

2017-12-01

In the present study, surface texture features and chemical properties of two types of cokes, made from coal tar by either 1-stage heat treatment or 2-stage heat treatment, were researched. The relationship between surface texture characteristics and the chemical properties was identified through molecular weight distribution, insolubility of coal tar, weight loss with temperature increase, coking yield, and polarized light microscope analysis. Rapidly cleared anisotropy texture in cokes was observed in accordance with the coking temperature rise. Quinoline insolubility and toluene insolubility of coal tar increased with a corresponding increases in coking temperature. In particular, the cokes produced by the 2-stage heat treatment (2S-C) showed surface structure of needle cokes at a temperature approximately 50°C lower than the 1-stage heat treatment (1S-C). Additionally, the coking yield of 2S-C increased by approximately 14% in comparison with 1S-C.

The world coke market. Problems and outlook

International Nuclear Information System (INIS)

Anon.

1998-01-01

Outlooks to the world coke market are considered with regard to supply and demand as well as the current state of capacities for its production in some countries of Asia, Western and Eastern Europe, USA. In experts opinion increase of coke import from China, increase in service life of currently operating coke furnaces, as well as more extensive use of PCI coal mixture are among the most feasible opportunities for its Western consumers [ru

Combined effects of petrographic and technological parameters on strength of porous coke substance

Energy Technology Data Exchange (ETDEWEB)

Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

1983-01-01

A laboratory study was undertaken to study the combined effects of the basic petrographic characteristics of Kuzbas coal blends and the technological carbonization parameters on the structural strength of the porous coke. Strength tests were carried out on the original coke and the products of partial gasification with carbon dioxide under conditions simulating those inside blast furnaces. Properties of the 14 samples of Kuzbas coals and composition of the four coal blends made from them are listed. It was concluded that the structural strength of coke was most strongly influenced by the average reflectance index and bulk density of the charge. Also, charge compaction can largely offset the adverse influence of petrographic heterogeneity on the strength of the coke. 10 references, 3 tables.

Shaft-retort for treating waste materials, like washery waste, bituminous shale, oil-bearing sands and the like

Energy Technology Data Exchange (ETDEWEB)

Koppers, H

1916-10-29

A shaft-retort for converting waste materials, like washery waste, bituminous shale, oil-bearing sands, brown coal and non-coking mineral coal to oil and tar by supplying heat through the shaft wall formed of an iron-sheet to the material, which is forced through a feeding member perforated for the removal of gases and vapors, and moved downward in a thin layer on the shaft wall; that is characterized by the fact that the iron heating sheet is made rotatable for the purpose of equalizing overheating of itself and the material to be treated.

Quality-oriented production of brown-coal coke with due regard to its application in metallurgy and environmental protection; Qualitaetsgerechte Erzeugung von Braunkohlenkoks unter Beruecksichtigung der Anwendung in Metallurgie und Umweltschutz

Energy Technology Data Exchange (ETDEWEB)

Achtelik, M.; Erken, M.; Juessen, P.; Knapp, A. [Rheinbraun AG, Koeln (Germany)

1998-12-31

In the nineteen seventies the Fortuna Nord refining factory of Rheinbraun AG began to restructure its operations from domestic coal briquetting to the manufacture of industrial products. One of these products, high-temperature brown-coal coke, is produced in two hearth-type furnaces. Coke produced in these plants is mainly used in metallurgy and environmental engineering, in the latter especially for flue gas purification. Rheinbraun has succeeded in introducing a quality management system for brown-coal coke which ensures high quality and security of supply. (orig.) [Deutsch] Im Veredlungsbetrieb Fabrik Fortuna-Nord der Rheinbraun AG begann in den 70er Jahren der Strukturwandel vom Hausbrandbrikett zu Industrieprodukten. Eins dieser Produkte, der Hochtemperatur-Braunkohlenkoks, wird in zwei Herdofenanlagen erzeugt. Die Haupteinsatzbereiche des Herdofenkokses sind die Metallurgie sowie der Umweltschutz und hier insbesondere die Rauchgasreinigung. Um die hohe Produktqualitaet und die Liefersicherheit zu gewaehrleisten, hat Rheinbraun ein Qualitaetsmanagementsystem fuer Braunkohlenkoks erfolgreich eingefuehrt. (orig.)

Future demands for imported coal in Asian countries

International Nuclear Information System (INIS)

Kimura, T.

1991-01-01

This paper reports that one of the main characteristics of international coal trade in the 1980's was a much higher growth rate recorded in steam coal trade than in coking coal trade. Another was that coal import in Asia started to expand rapidly at the start of the 1980's. Increased coal imports by Asian countries is primarily attributed to growing steam coal imports. Steam coal accounted for more than two-thirds of the additional coal imports by Asian countries between 1980 and 1988. Nonetheless, coking coal still forms the largest segment of Pacific coal trade. Only in the early 1990's is steam coal trade expected to exceed coking coal trade in the Pacific

Assessment of thermal efficiency of heat recovery coke making

Science.gov (United States)

Tiwari, H. P.; Saxena, V. K.; Haldar, S. K.; Sriramoju, S. K.

2017-08-01

The heat recovery stamp charge coke making process is quite complicated due to the evolved volatile matter during coking, is partially combusted in oven crown and sole flue in a controlled manner to provide heat for producing metallurgical coke. Therefore, the control and efficient utilization of heat in the oven crown, and sole flue is difficult, which directly affects the operational efficiency. Considering the complexity and importance of thermal efficiency, evolution of different gases, combustion of gasses in oven crown and sole flue, and heating process of coke oven has been studied. A nonlinear regression methodology was used to predict temperature profile of different depth of coal cake during the coking. It was observed that the predicted temperature profile is in good agreement with the actual temperature profile (R2 = 0.98) and is validated with the actual temperature profile of other ovens. A complete study is being done to calculate the material balance, heat balance, and heat losses. This gives an overall understanding of heat flow which affects the heat penetration into the coal cake. The study confirms that 60% heat was utilized during coking.

Scientific Council of the State Committee for Science and Technology on the problem 'New processes in the coking industry', Coke-Chemistry Section of the Scientific-Technical Council of the Ministry of Ferrous Metallurgy of the USSR and of the Central Administration of the Scientific-Technical Branch of Ferrous Metallurgy

Energy Technology Data Exchange (ETDEWEB)

Bukvareva, O.F.

1986-12-01

A report is presented on 3 conferences on the development of the Soviet coking industry held in February and April 1986. Papers delivered at the conferences and selected recommendations for development of equipment for coking, coking systems, optimization of coal mixtures for coking, environmental protection and research programs on coking are reviewed. The following problems were discussed: modernization of coke oven design, selecting the optimum size of coke ovens, prospects for dry coke quenching in the USSR, evaluation of operation of systems for dry coke quenching, utilization of waste heat from coke quenching for heat treatment of coal mixtures for coking, research programs on coking in the 12th five-year plan (1986-1990), partial briquetting of coal mixtures for coking and selecting optimum binders for partial briqetting, formed coke processes, economic analysis of formed coke processes, fire-resistant bricks and elements for coke oven construction, new coking technologies, pollution control in coking plants.

Numerical analysis of macro-crack formation behavior within the lump coke; Cokes sonai kiretsu shinten kiko no kaiseki

Energy Technology Data Exchange (ETDEWEB)

Aoki, H; Sato, H; Miura, T [Tohoku University, Sendai (Japan). Faculty of Engineering

1995-03-15

The thermal stress analysis within lump coke was studied in order to investigate macro-crack formation and deformation behavior which strongly influence heat and mass transfer in a coke oven chamber. The dilatation of plastic layer, heating rate dependence of thermophysical and mechanical properties of coal/coke, creep in the plastic and semi-coke layers, macro-crack propagation and radiative heat transfer within the macro-crack were considered in an analytical model. The macro-crack propagation was determined from the estimated crack tip stress intensity factor, K{sub I}, at the macro-crack tip compared with the plane strain fracture toughness, K{sub IC}, through the unsteady-state calculation. Calculated results on crack formation and deformation behavior of lump coke were in good agreement with experimental observations in a laboratory-scale oven chamber. The analytical model could predict micro-crack formation within the lump coke normal to the heated wall and the coke surface close to the heated wall. 12 refs., 13 figs.

Surface structure and oxidation reactivity of oil sand coke particles

Energy Technology Data Exchange (ETDEWEB)

Fairbridge, C.; Palmer, A.D.; Ng, S.H.; Furimsky, E.

1987-05-01

Fractions of particles of varying mean diameter were isolated from coke obtained from the fluid coking of Athabasca bitumen. Correlations were established between the rate of oxygen sorption and the apparent surface area as measured by carbon dioxide adsorption. The rate of oxygen sorption, r/sub o/, could be related to particle radius, R, by r/sub o/ varying with R/sup D/ T over a range of particle size where D is the fractal dimension of the coke. The existence of such correlations may be related to the iterative processes which form the particles. 14 refs., 5 figs., 2 tabs.

Application of flotational reagents obtained from coke-industry byproducts

Energy Technology Data Exchange (ETDEWEB)

N.I. Nikitin; I.N. Nikitin; N.I. Toporkova [Khar' kov Polytechnic Institute (Ukraine)

2007-06-15

Today, the operational efficiency of coal-preparation shops at coke plants largely depends on the flotation process, since flotation is the basic method of regenerating the slurry water in the water-slurry systems and the basic enrichment process for small-grain coal slurries. At The Coal-Chemistry Institute, attempts have been made to address the growing demand for readily available and relatively inexpensive flotational reagents. In particular, a list of promising coke-industry byproducts for use as flotational reagents has been compiled, and the possibility of reducing their toxicity has been established. In addition, various industrial byproducts and wastes have been investigated in terms of flotational activity.

Coal 1992

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

ACR's Coal 1992, the successor to the ACR Coal Marketing Manual, contains a comprehensive set of data on many aspects of the Australian coal industry for several years leading up to 1992. Tables and text give details of coal production and consumption in New South Wales, Queensland and other states. Statistics of the Australian export industry are complemented by those of South Africa, USA, New Zealand, Canada, Indonesia, China, Colombia, Poland and ex-USSR. Also listed are prices of Australian coking and non-coking coal, Australian coal stocks (and those of other major countries), loading port capacities, freight rates and coal quality requirements (analysis of coals by brand and supplier). A listing of Australian coal exporting companies is provided. A description of the spot Coal Screen Dealing System is given. World hard coal imports are listed by country and coal imports by major Asian countries tabulated. A forecast of demand by coal type and country up to the year 2000 is included.

New processes in iron metallurgy discussed by the Coking Section of the Scientific Council of the Main Committee of Science and Technology of the USSR

Energy Technology Data Exchange (ETDEWEB)

Bukvareva, O.F.

1991-02-01

Discusses problems evaluated in October 1990 by the Section during the meeting devoted to research programs in the twelfth five-year plan, research and development of continuous coking methods, prospects for new coke quenching processes. Selected research programs, coordinated research programs and development programs as well as recommendations for future research programs are evaluated. The following research programs aimed at use of weakly caking and noncaking coals in the coking plants are evaluated: coal preheating and charging preheated mixtures to coke ovens, partial coal charge briquetting and equipment for coal briquetting, development of commercial systems for packing coal charges in coke ovens, production of formed coke for metallurgy, processes for coal gas cleaning (especially ammonia separation), development of systems for utilization of waste heat from dry coke quenching for coal charge preheating. Participation of individual research institutes in the programs is discussed. The most significant projects of individual institutes are discussed. Recommendations for research programs for the period 1991 to 1995 are made.

The influence of calcination on the physical and chemical properties of petroleum and mixed cokes

Energy Technology Data Exchange (ETDEWEB)

Sikora, K; Syrek, H

1980-01-01

Freshly prepared petroleum and coal-petroleum cokes, before utilization for the production of various materials, are subjected to calcining--thermal treatment in a neutral or reducing atmosphere without the admission of air at less than or equal to 1400/sup 0/. During calcining, stabilization of the physical and chemical properties of the cokes takes place. The properties of the obtained coke depend chiefly on the calcining time and temperature. During calcining, volatile substances are removed almost completely from the coke; the coke density is increased, and its structure is put in order; the electrical conductivity is improved; the mechanical strength is increased; and the reactivity of the coke is decreased. Laboratory studies were conducted on calcining mixed coal-petroleum cokes of two grades at 1200, 1250, and 1300/sup 0/ for 2-6 h. In the calcining products the content of volatile substances, the ash content, S content, and density were determined. It was ascertained that calcining of mixed coal-petroleum cokes goes analogously to calcining of pure petroleum cokes. Raising the temperature and increasing the time of calcining has a substantial effect on improvement of coke physical and chemical properties. For high-quality coke, calcining is to be carried out at greater than or equal to 1300/sup 0/ for 4-6 h, for ordinary coke at > 1200/sup 0/ and greater than or equal to 4 h. The results are regarded as starting data for an industrial study of the calcining process.

Combined effects of petrographic and technological parameters on strength of porous coke substance

Energy Technology Data Exchange (ETDEWEB)

Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

1983-09-01

The proportion of coke in modern blast furnaces has been reduced and at the same time ore burdens have increased. The coke itself now derives from a much wider range of coals. Laboratory tests related to the structural strength of cokes were carried out with charges composed of 14 representative coals. Results showed that vitrinite reflectance and bulk density were the critical parameters, followed by petrographic composition. Increasing bulk density of the charge from 0.6 to 0.9 g/cm/sup 3/ produces coke with a structural strength which counteracts the effects of increasing diversity in both petrography and reflectance in any one charge.

The coal deposits of the Alkali Butte, the Big Sand Draw, and the Beaver Creek fields, Fremont County, Wyoming

Science.gov (United States)

Thompson, Raymond M.; White, Vincent L.

1952-01-01

Large coal reserves are present in three areas located between 12 and 20 miles southeast of Riverton, Fremont County, central Wyoming. Coal in two of these areas, the Alkali Butte coal field and the Big Sand Draw coal field, is exposed on the surface and has been developed to some extent by underground mining. The Beaver Creek coal field is known only from drill cuttings and cores from wells drilled for oil and gas in the Beaver Creek oil and gas field.These three coal areas can be reached most readily from Riverton, Wyo. State Route 320 crosses Wind River about 1 mile south of Riverton. A few hundred yards south of the river a graveled road branches off the highway and extends south across the Popo Agie River toward Sand Draw oil and gas field. About 8 miles south of the highway along the Sand Draw road, a dirt road bears east and along this road it is about 12 miles to the Bell coal mine in the Alkali Butte coal field. Three miles southeast of the Alkali Butte turn-off, 3 miles of oiled road extends southwest into the Beaver Creek oil and gas field. About 6 miles southeast of the Beaver Creek turn-off, in the valley of Little Sand Draw Creek, a dirt road extends east 1. mile and then southeast 1 mile to the Downey mine in the Big Sand Draw coal field. Location of these coal fields is shown on figure 1 with their relationship to the Wind River basin and other coal fields, place localities, and wells mentioned in this report. The coal in the Alkali Butte coal field is exposed partly on the Wind River Indian Reservation in Tps. 1 and 2 S., R. 6 E., and partly on public land. Coal in the Beaver Creek and Big Sand Draw coal fields is mainly on public land. The region has a semiarid climate with rainfall averaging less than 10 in. per year. When rain does fall the sandy-bottomed stream channels fill rapidly and are frequently impassable for a few hours. Beaver Creek, Big Sand Draw, Little Sand Draw, and Kirby Draw and their smaller tributaries drain the area and flow

Annual bulletin of coal statistics for Europe. Vol. IX

Energy Technology Data Exchange (ETDEWEB)

1974-01-01

Tables are presented giving the following information: Production, imports, exports, and deliveries of solid fuels with the subdivisions: hard coal, patent fuel, and cokeoven coke; gas coke; brown coal, brown coal briquets, and brown coal coke; and pech coal (hard brown coal produced in the area between the rivers Inn and Lech); Hard coal mines (structure of production, employment and productivity of labor); Brown coal mines (production, employment and productivity of labor); Imports of solid fuels, by country; Exports of solid fuels, by country; and Production of hydroelectric energy and natural gas, and deliveries of petroleum products for inland consumption.

PROSPECTS FOR COKE BREEZE RECOVERY

Directory of Open Access Journals (Sweden)

D. N. Mihnovets

2012-01-01

Full Text Available Researches give grounds to believe in the possibility of receiving briquettes from coke waste mixed with peat dry coal and their use for smelting iron in the cupola or as a household fuel.

Australia's export coal industry: a project of the Coal Australia Promotion Program. 2. ed.

International Nuclear Information System (INIS)

1995-01-01

This booklet presents an overview of the Australian coal industry, emphasises the advantages of using Australian coal and outlines government policies, both Commonwealth and State, which impact on coal mine development, mine ownership and coal exports. It also provides information on the operations and products of each producer supplying coal and coke to export markets and gives contact details for each. The emphasis is on black coal, but information on coal briquettes and coke is also provided. Basic information on the rail networks used for the haulage of export coal and on each of the bulk coal loading terminals is also included.(Author). 3 figs., photos

High coking value pitch

Science.gov (United States)

Miller, Douglas J.; Chang, Ching-Feng; Lewis, Irwin C.; Lewis, Richard T.

2014-06-10

A high coking value pitch prepared from coal tar distillate and has a low softening point and a high carbon value while containing substantially no quinoline insolubles is disclosed. The pitch can be used as an impregnant or binder for producing carbon and graphite articles.

Utilisation of the binders prepared from coal tar pitch and phenolic resins for the production metallurgical quality briquettes from coke breeze and the study of their high temperature carbonization behaviour

Energy Technology Data Exchange (ETDEWEB)

Benk, Ayse [University of Erciyes, Faculty of Art and Science, Department of Chemistry, 38039, Kayseri (Turkey)

2010-09-15

To reduce the cost of the formed coke briquettes which can be used as a substitute fuel to the metallurgical coke for the blast furnace from the coke breeze alternative binders and their blends were used. The high temperature behavior was investigated. The binders tested were: the nitrogen blown, air blown coal tar pitch and the blend of air blown coal tar pitch with the phenolic resins blends. The phenolic resin blends were prepared by mixing equal amount of resole and novalac. From the results, nitrogen blowing resulted in the weakest briquettes. The air blowing procedure should be preferred in place of nitrogen blowing for this purpose. When the air blown coal tar pitch was used alone as a binder, the briquettes must be cured at 200 C for 2 h, then carbonized at a temperature above 670 C. Since it requires higher temperature at carbonization stage, using air blown coal tar pitch alone as a binder was not economical. Therefore, the briquettes were prepared from the blended binder, containing air blown coal tar pitch and phenolic resins blend. The optimum amount of air blown coal tar pitch was found to be 50% w/w in the blended binder. Curing the briquettes at 200 C for 2 h was found to be sufficient for producing strong briquettes with a tensile strength of 50.45 MN/m{sup 2}. When these cured briquettes were carbonized at temperatures 470 C, 670 C and 950 C, their strength were increasing continuously, reaching to 71.85 MN/m{sup 2} at the carbonization temperature of 950 C. These briquettes can be used as a substitute for the metallurgical coke after curing; the process might not require un-economical high temperature carbonization stage. (author)

Coal - 97

International Nuclear Information System (INIS)

Sparre, C.

1997-01-01

The report deals with the use of coal and coke during 1996. Some information about techniques, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from SCB have also been used. The use of steam coal for heating purposes during 1996 was 1,2 mill tons and 50% higher than in 1995. The increase is probably temporary and due to high prices of electricity because of lack of water power. The co-generation plants were the main users of coal. The minor plants have increased their use of forest fuels. Probably the use of steam coal will go down in the immediate years both in the heat generating and the co-generation plants. During the top year 1987 coal was used in 18 hotwater plants and 11 co-generation plants. 1996 these figures are 3 and 12. Taxes and environmental reasons explain this trend. The use of steam coal in the industry has been constant at the level 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1996 was 1,6 mill tons like the year before. 1,2 mill tons coke were produced. The coke consumption in the industry was 1,5 mill tons. 0,3 mill tons of coke were imported. The average price of steam coal imported in Sweden in 1996 was 340 SEK/ton or 2% higher than in 1995. For the world, the average import price was 51,5 USD/ton, nearly the same as the year before. The contract prices for delivery during 1997 are about equal as the end of 1996. All Swedish plants meet their emission limits of dust, SO 2 and NO x given by county administrations or concession boards

Carbon dioxide emission in hydrogen production technology from coke oven gas with life cycle approach

Directory of Open Access Journals (Sweden)

Burmistrz Piotr

2016-01-01

Full Text Available The analysis of Carbon Footprint (CF for technology of hydrogen production from cleaned coke oven gas was performed. On the basis of real data and simulation calculations of the production process of hydrogen from coke gas, emission indicators of carbon dioxide (CF were calculated. These indicators are associated with net production of electricity and thermal energy and direct emission of carbon dioxide throughout a whole product life cycle. Product life cycle includes: coal extraction and its transportation to a coking plant, the process of coking coal, purification and reforming of coke oven gas, carbon capture and storage. The values were related to 1 Mg of coking blend and to 1 Mg of the hydrogen produced. The calculation is based on the configuration of hydrogen production from coke oven gas for coking technology available on a commercial scale that uses a technology of coke dry quenching (CDQ. The calculations were made using ChemCAD v.6.0.2 simulator for a steady state of technological process. The analysis of carbon footprint was conducted in accordance with the Life Cycle Assessment (LCA.

Utilization of formed coke from HBNPC in the Dunkerque blast furnaces

Energy Technology Data Exchange (ETDEWEB)

Le Scour, C; Capelani, R

1978-01-01

Recalls the aspects involved in the manufacture of formed coke together with the coke characteristics. Describes the features of blast-furnaces No. 1 and No. 2 at Dunkerque. The blend used for producing the ovoids is composed of 70 to 80% non-coking coal and the ovoids are carbonized at 900 C. The first stage of the tests was carried out with 25% formed coke and the second stage with 22%. The formed coke was charged separately. The results were as follows: the coke rate was comparable and the permeability identical; there was no change in the behaviour of the furnace chamber and no problems were experienced at the hearth stage. The replacement of 30% of the conventional coke by HBNPC formed coke seemed a practical proposition.

Practical aspects of coking in Cundinamarca y Boyacá

Directory of Open Access Journals (Sweden)

Segundo Manuel Romero-Balaguera

2014-12-01

Full Text Available Taking advantage of the excellent qualities of the studied coals from the coalfields in Cundinamarca and terms of the types of coking ovens, for excellent performance and quality that allows them to be very competitive.The international market is very demanding in terms of the quality of coke and CRI and CSR indexes, that is why coals laboratories were implemented and improved the system of sampling and analysis of laboratories for more agile and modern. Mixtures were made with the test methodology and empirical methods combining swelling index and rank cals were the theree main types: high, medium and low volatile. But with studies and techological change and enviromental control, process is managed, allowing the coke industry to serve as a development center for the promotion of industries in the central area of this country. In the study the whole process is presented beginning with the explotaitation of coking coals, the care that must be taken into account to mainttain good quality, transport and enviromental measures, the process of crushing and grinding to prepare the optimal mix and laboratory tests necessary to maintain quality control, the types of ovens in Boyacá Colombia, yields and advances in the se technologies, and finally, the system shutdown process. All of the above was addressed in order to add value to the product with the fulfillment of the international market standards.

Reuse and activation of petroleum coke to remove metals in water

International Nuclear Information System (INIS)

Cardona, Santiago

2006-01-01

In the investigation I am reused the coke generated in the refinancing of the petroleum. It was proposed to activate al coke with characteristics of a carbon activated commercial and subsequently to use it to remove silver and present mercury in water. The carbon activated produced and the carbon activated commercial, LQ1000, they were characterized with the norms ASTM, indicate of iodine, area superficial al blue of methylene and indicate of blue of methylene and the results were compared. Likewise in the process of adsorption, the process of adsorption itself model with the equations of Freundlich and Langmuir. The activation of the coke I am planned through a design of experiments four factorial. The 16 coals produced were submitted al process of adsorption silver and mercury by duplicate. The study I report al coke activated as better adsorbent than the LQ1000 and with a smaller cost of fabrication but with a smaller one area superficial that the commercial one. The results obtained permit to produce carbon activated from the coke but economic to compete with the commercial coals activate

Coal chemistry and technology. Komur Kimyasi ve Teknolojisi

Energy Technology Data Exchange (ETDEWEB)

Kural, O [ed.

1988-01-01

The 18 chapters cover the following topics: mining in Turkey; formation, petrography and classification of coal; chemical and physical properties of coal; mechanical properties of coal; spontaneous combustion of coal and the methods of prevention; sampling of coal; coal preparation and plants; desulfurization of coal; bituminous coal and its consumption; lignite and its consumption; world coal trade and transportation; other important carbon fuels; briquetting of coal; carbonization and coking formed coke; liquefaction of coal; gasification of coal; underground gasification of coal; and combustion models, fluidized-bed combustion, furnaces. An English-Turkish coal dictionary is included. 641 refs., 244 figs., 108 tabs.

Research and development of SCOPE21 (super coke oven for productivity and environment enhancement towards the 21st century)

Energy Technology Data Exchange (ETDEWEB)

Oshima, H.; Otsuka, J.; Nishioka, K.; Kamijo, T. [Japan Iron and Steel Federation, Tokyo (Japan)

2000-07-01

Coke ovens in Japan have 28 years of service on the average and the supply of coke is foreseen to suffer a shortage at the early years of the 21st century. Furthermore, the existing cokemaking process entails a lot of issues such as an effective use of coal resources, an adverse effect on environment. Thus, the Japan Iron and Steel Federation has launched a 9 year research programme called SCOPE 21 in collaboration with the Center for Coal Utilization, Japan in 1994. The programme pursues the following targets. The use ratio of poor coking coal increases from 20-50% with the improvement of coking property of coal by rapid heating and the increase of bulk density by mixing the briquetted coal. The coking time is reduced by rapid heating to 350 to 400{degree}C at the preheater, coking up to 750-850{degree}C at oven chamber, and reheating up to 1000{degree}C at the upgrading chamber, thus trebling productivity. The environment of coke oven is improved by emission free system and by improving the heating system of coke oven to reduce NOx in oven exhaust gas. After two years of preliminary feasible study the programme has advanced to basic research and to a bench scale test. It is in a stage of the construction of a pilot plant. This report describes the outline of the programme and the results obtained through the basic research and the bench scale plant tests. 2 refs., 17 figs., 5 tabs.

PETROBRAS green petroleum coke used as partial replacement for coal injected mixtures in blast furnaces; Utilizacao do coque verde de petroleo da PETROBRAS em substituicao parcial ao carvao mineral das misturas injetadas em altos fornos

Energy Technology Data Exchange (ETDEWEB)

Silva, Agenor Medrado da; Medrado, Swami Botelho; Noblat, Sebastiao Jorge Xavier [Companhia Siderurgia Nacional. CSN. Gerencia Geral de Processos Siderurgicos. RJ (Brazil)], e-mails: ams@csn.com.br, swami@csn.com.br, s.noblat@csn.com.br; Carvalho Junior, Joao Andrade de [Universidade Estadual Paulista Julio de Mesquita Filho. Faculdade de Engenharia de Guaratingueta. Departamento de Energia, SP (Brazil)], e-mail: joao@feg.unesp.br

2010-04-15

The PETROBRAS produced green petroleum coke (GPC) is a carbon rich fuel, virtually ash-free, with low sulfur content and is a fuel suitable to replace metallurgical coke in blast furnaces. The GPC was tested in a pulverized coal injection simulator built in the Volta Redonda research center. It presented a low burning efficiency due to low volatile material content and high substitution rate by the carbon content. The industrial-scale tests were carried out in blast furnaces with up to 50% PETROBRAS GPC in the coal blends, which has never been done before in the steel industry. The injected coal/CVP mixtures produced no negative side effects in the blast furnace grinding systems, pneumatic conveying or operating process. The mixture burning process inside the blast furnace, showed a decrease in fuel consumption, with a significant reduction in metallurgical coke consumption. The industrial-scale tests of the GPC mixtures did not reach the 70% maximum for lack of the GPC feedstock, it being necessary to continue with standard coal mixtures. (author)

Economic aspects of coal deposits exploration of the Ulug-Khem basin (Tuva

Directory of Open Access Journals (Sweden)

Lebedev V.I.

2017-06-01

Full Text Available in accordance with the article, 11 deposits coal on the territory of Tuva are accounted by State Reserves Register of the Russian Federation, the total profitable reserves are estimated at 1,12 billion tons whereof 936.6 thousand tons are dealt with as coking coals. The vast majority of explored deposits of coals of the republic are concentrated in the Ulugh-Khem basin, the total projected resources of which exceed 20 bill.t. It is substantiated that coking coal of the Ulugh-Khem basin is the most competitive resource of Tyva Republic. Low ash content, excellent caking index, low sulfur and phosphorus in coking coal of ranks GG and GZh indicate their high quality, according to these characteristics GG, GZh coal ranks take precedence over Kuznetsk and Pechora coals. About 70 bill.t of coking coal are annually mined in Russia, but there is a deficit on certain coal ranks. It is primarily related to internal prices increase for coking coal in Russia. According to forecasts of researchers coal deficit will rise up to 15–17 bill.t in the country.

Test work of sand compaction pile method on coal ash soil foundation. Sekitanbai jiban ni okeru sand compaction pile koho no shiken seko

Energy Technology Data Exchange (ETDEWEB)

Goto, K.; Maeda, S.; Shibata, T. (The Kansai Electric Power Co. Inc., Osaka (Japan))

1992-01-25

As an electric power supply source after the 1990 {prime}s, Nos. 5 and 6 units are additionally being constructed by Kansai Electric Power in its Himeji Power Station No.1 which is an exclusively LNG burning power station. The additional construction site of those units is of soil foundation reclaimed with coal ash which was used residual product in the existing No.1 through No.4 units. As a result of soil foundation survey, the coal ash layer and sand layer were known to be of material to be possibly liquidized at the time of earthquake. As measures against the liquidization, application was basically made of a sand compaction pile (SCP) method which is economical and abundant in record. However, that method was so short of record in the coal ash layer that its evaluation was difficult in soil reforming effect. Therefore, its applicability was evaluated by a work test on the site, which resulted in a confirmation that the coal ash as well as the sand can be sufficiently reformed by the SCP method. Started in September, 1991, the additional construction of Nos. 5 and 6 units in Himeji Power Station No.1 uses a 1.5m pitch SCP method to reform the soil foundation. 3 refs., 10 figs., 1 tab.

Arsenic in coal and its mode of occurrence

Energy Technology Data Exchange (ETDEWEB)

Duck, N W; Himus, G W

1951-07-01

Arsenic concentrations were determined in 25 coals and their respective ashes, and in 6 commercial cokes. The form of occurrence of As was established in addition to its behavior during combustion. Coals were combusted at temperatures ranging from 290 to 1050/sup 0/C (approximate temperature attained in a coke oven). Float-sink tests were performed utilizing mixtures of toluene and carbon tetrachloride. Elemental As was determined by a modification of the Gutzeit process. Arsenic occurred as arsenopyrite in the coals, and to some extent as arsenites and arsenates in the ash. Over 50% of the As was retained in the ash, and coke ash contained a higher As concentration than the original coke. A portion of the As was said to be in organic association in the coals.

Japanese coke plant follows US lead

Energy Technology Data Exchange (ETDEWEB)

1980-06-01

Nippon Steel has acquired the first licence for a US Steel/Firma Carl Still process for cleaning coke oven flushing liquor. The process is installed at 3 US Steel preheated coal batteries and is now being used at Nippon Steel's Muroran works. The process is important to the re-use of the water for quenching and is a vital first step in making the liquor harmless to the environment. It is particularly useful in plants using preheated coal where there is likely to be carry over of fine coal particles.

USA coal producer perspective

Energy Technology Data Exchange (ETDEWEB)

Porco, J. [Alpha Natural Resources, Latrobe, PA (US). Alpha Energy Global Marketing

2004-07-01

The focus is on the Central Appalachian coal industry. Alpha Natural Resources was formed in 2002 from Pittston Coal's Virginia and Coastal operations. AMCI's U.S. operations and Mears Enterprises in Pennsylvania were acquired later. The company produces 20-21 million tonnes per year and sells 20 million tonnes of steam coal and 10 million tonnes of exports, including some coal that is brokered. Foundry coke is a major product. Capital investment has resulted in increased productivity. Central Appalachia is expected to continue as a significant coal-producing region for supplying metallurgical coke. Production is expected to stabilize, but not increase; so the mines will have a longer life. 31 slides/overheads are included.

Life-cycle assessment for coal-based methanol production in China

DEFF Research Database (Denmark)

Li, Changhang; Bai, Hongtao; Lu, Yuanye

2018-01-01

using the coal coking technology than by producing methanol using the coal gasification technology, especially in terms of acidification, global warming, and photochemical oxidation. In particular, significantly less environmental harm in terms of climate change and radiation is caused by the coal...... coking technology than by the coal gasification technology. Different sub-processes clearly make different contributions to environmental harm. The results indicated that the methanol production process, heating, and desalination are the main sources of environmental harm for both the coal gasification...... technology and coal coking technology. Importantly, the public engineering process rather than the methanol production process itself was found to determine emissions for the different methanol production methods....

A newer concept of setting up coal refineries in coal utilising industries through environmentally sound clean coal technology of organosuper refining of coals

International Nuclear Information System (INIS)

Sharma, D.K.

1994-01-01

In order to reduce the losses of premium organic matter of coal and its immense potential energy which is present in the form of stronger interatomic and intramolecular bonding energies, a newer and convenient technique of recovering the premium organic matter from low grade coals by organosuper-refining technique which operates under ambient pressure conditions has been developed. The residual coal obtained can be used as environmentally clean fuel or as a feedstock for the industries based on carbonization and gasification. It is suggested that a beginning be made by setting up coal refineries in coal utilizing industries on the basis of the presently developed new technology of organosuper-refining of coals to recover premium grade organic chemical feed stocks from coals before utilizing coal by techniques such as bubble bed or recirculatory fluidized bed or pulverized coal combustion in thermal power stations, carbonization in steel plants or other carbonization units, gasification in fertilizer industries or in integrated coal gasification combined cycle power generation. Thus, coal refineries may produce value added aromatic chemical feed stocks, formed coke or coke manufacturing; and carbon fillers for polymers. (author). 100 refs., 1 fig

Understanding the mechanisms behind coking pressure: Relationship to pore structure

Energy Technology Data Exchange (ETDEWEB)

John J. Duffy; M. Castro Diaz; Colin E. Snape; Karen M. Steel; Merrick R. Mahoney [University of Nottingham, Nottingham (United Kingdom). Nottingham Fuel and Energy Centre, School of Chemical, Environmental and Mining Engineering

2007-09-15

Three low volatile coals A, B and C with oven wall pressures of 100 kPa, 60 kPa and 20 kPa respectively were investigated using high-temperature rheometry, {sup 1}H NMR, thermogravimetric analysis and SEM, with the primary aim to better understand the mechanisms behind the coking pressure phenomenon. Rheometer plate displacement measurements ({Delta}L) have shown differences in the expansion and contraction behaviour of the three coals, which seem to correlate with changes in rheological properties; while SEM images have shown that the expansion process coincides with development of pore structure. It is considered that the point of maximum plate height ({Delta}L{sub max}) prior to contraction may be indicative of a cell opening or pore network forming process, based on analogies with other foam systems. Such a process may be considered important for coking pressure since it provides a potential mechanism for volatile escape, relieving internal gas pressure and inducing charge contraction. For coal C, which has the highest fluidity {delta}L{sub max} occurs quite early in the softening process and consequently a large degree of contraction is observed; while for the lower fluidity coal B, the process is delayed since pore development and consequently wall thinning progress at a slower rate. When {Delta}L{sub max} is attained, a lower degree of contraction is observed because the event occurs closer to resolidification where the increasing viscosity/elasticity can stabilise the expanded pore structure. For coal A which is relatively high fluidity, but also high coking pressure, a greater degree of swelling is observed prior to cell rupture, which may be due to greater fluid elasticity during the expansion process. This excessive expansion is considered to be a potential reason for its high coking pressure. 58 refs., 15 figs., 1 tab.

Possibilities of production of smokeless fuel via carbonization of Czech coals

Energy Technology Data Exchange (ETDEWEB)

Buchtele, J.; Straka, P. [Inst. of Rock Structure and Mechanics, Prague (Czechoslovakia)

1995-12-01

It was consumed 48 -51 % of hard coal (total output 28 - 30 Mt/year) in a long period for the production of coke. It appears to be anomaly in comparison with other coke producers in Europe and in the world, it was predeterminated by {open_quotes}steel conception{close_quotes} of state`s economics. The production of coke reached 10-11 Mt/year in former Czechoslovakia in the period 1970-1990. A considerable quantity 1.2 - 1.7 Mt/year of produced coke was utilized for heating. In comparison, 7-5.4 Mt coke/year was it in Poland for the heating. Al coke production is realized on the basis of Czech hard coals mined in the southern part of Upper Silesian Coal District. The coke production is operated in multi-chamber system with full recovery of chemical products (gas, raw tar, raw benzene, amonium etc.). The future trend of smokeless fuel production in Czech Republic makes for to the non-recovery coke oven, it means to two-product processes (coke + reduction gas, coke + electricity and so on). Jewell--Thompson coke oven (hard coal) and Salem oven (ignites) represent nonrecovery nowadays. The possibility of it`s application in Czech Republic are discussed. Jumbo coking reactor system (European project No. 500 to the Eureka programme) produces primarily metallurgical coke. The strong Clean Air Act suspends the production of smokeless fuel in multi-chamber system also in Czech Republic for the future period 2010-2020.

Fly ashes from coal and petroleum coke combustion: current and innovative potential applications.

Science.gov (United States)

González, Aixa; Navia, Rodrigo; Moreno, Natalia

2009-12-01

Coal fly ashes (CFA) are generated in large amounts worldwide. Current combustion technologies allow the burning of fuels with high sulfur content such as petroleum coke, generating non-CFA, such as petroleum coke fly ash (PCFA), mainly from fluidized bed combustion processes. The disposal of CFA and PCFA fly ashes can have severe impacts in the environment such as a potential groundwater contamination by the leaching of heavy metals and/or particulate matter emissions; making it necessary to treat or reuse them. At present CFA are utilized in several applications fields such as cement and concrete production, agriculture and soil stabilization. However, their reuse is restricted by the quality parameters of the end-product or requirements defined by the production process. Therefore, secondary material markets can use a limited amount of CFA, which implies the necessity of new markets for the unused CFA. Some potential future utilization options reviewed herein are zeolite synthesis and valuable metals extraction. In comparison to CFA, PCFA are characterized by a high Ca content, suggesting a possible use as neutralizers of acid wastewaters from mining operations, opening a new potential application area for PCFA that could solve contamination problems in emergent and mining countries such as Chile. However, this potential application may be limited by PCFA heavy metals leaching, mainly V and Ni, which are present in PCFA in high concentrations.

Negotiation of coal price in 1987

Energy Technology Data Exchange (ETDEWEB)

Chimura, Akira

1987-12-01

Price and amount of coking coal for the fiscal year 1987 was announced. Contracted coals were 5 types with Australia and 4 types with Canada by end Jan, 1987. Average price came down from 47.72 US dollar/t to 43.57, i.e., 4.15 US dollar/t price decline to the previous year. In addition, the number of the branded coal are negotiated with Australia is 23 cases, 5 brands with Canada, 1 with South Australia, 2 with USSR, and 3 with China. General trend of the price is as follows: Coking coal price is influenced by the decrease of the Japanese steel production as well as the world-wide surplus of coal, and all import prices have gone down except semi-caking coal of USA. Price level is very high in USA and Canada, but is low in Australia and others. Recently, strikes are frequent in South Africa and Canada; profit of coal mines is coming down; US dollar rate is sinking; contract quantity is shrinking; these give an estimate that both general coal and coking coal prices will not so easily go down further. (10 tabs)

Influence of coal batch preparation on the quality of metallurgical соkе

Directory of Open Access Journals (Sweden)

Катерина Олегівна Шмельцер

2015-10-01

Full Text Available To study the influence of coal batch properties on coke strength we have considered the quality of the coke produced at the plant in Krivoy Rog from 2008 till 2012. Such factors as the large number of coal suppliers, imprecise selection of the optimal degree of batch crushing result in the decline in coke quality, the batch density and contents of the lean class (<0,5 mm are not optimum; poor blending of the batch after crushing; increased moisture and ash content of the coking batch; and extreme fluctuation in the coal and batch characteristics. It was found that high humidity of coal batch and its large fluctuations has most profound effect on the mechanical properties of coke. Under deteriorating resource base the quality of the coking batch preparation is important, To have batch of proper quality the following key aspects must be taken into account: the batch must be crushed to an optimum degree that will result in leaning components decrease and increased contents of vitrivite in it which improves the sinterability and coking, and hence the quality of coke; the degree of mixing of the coking batch in all indices must be up to 98-99%, for uneven distribution in the coal chamber worsens the quality of coke

Complete physico-chemical treatment for coke plant effluents.

Science.gov (United States)

Ghose, M K

2002-03-01

Naturally found coal is converted to coke which is suitable for metallurgical industries. Large quantities of liquid effluents produced contain a large amount of suspended solids, high COD, BOD, phenols, ammonia and other toxic substances which are causing serious pollution problem in the receiving water to which they are discharged. There are a large number of coke plants in the vicinity of Jharia Coal Field (JCF). Characteristics of the effluents have been evaluated. The present effluent treatment systems were found to be inadequate. Physico-chemical treatment has been considered as a suitable option for the treatment of coke plant effluents. Ammonia removal by synthetic zeolite, activated carbon for the removal of bacteria, viruses, refractory organics, etc. were utilized and the results are discussed. A scheme has been proposed for the complete physico-chemical treatment, which can be suitably adopted for the recycling, reuse and safe disposal of the treated effluent. Various unit process and unit operations involved in the treatment system have been discussed. The process may be useful on industrial scale at various sites.

Polycyclic aromatic hydrocarbon contamination of American lobster, Homarus americanus, in the proximity of a coal-coking plant

Energy Technology Data Exchange (ETDEWEB)

Uthe, J F; Musial, C J

1986-11-01

Polycyclic aromatic hydrocarbons (PAH) are ubiquitous environmental contaminants resulting predominantly from anthropogenic pyrolytic and combustion processes. In addition to the usual methods of aerial and aqueous transport to the coastal marine environment substantial amounts of PAH are added through the use of products such as creosote, coal tar and coal tar pitch as preservative and antifouling agents in the marine environment. Many PAH compounds are known carcinogenic agents and are rapidly taken up by fish and shellfish from water. Therefore as human foodstuffs many of these shellfish species warrant monitoring for PAH. A study of PAH in lobster tissues has been carried out using lobsters captured in Sydney harbour, Nova Scotia, Canada. Two coal-coking ovens on the shore have discharged their liquid effluents into the harbour. Lobsters from this area were sampled in 1982 and 1984. This paper presents the materials and methods used in the sampling, the results and discussion of them. The results confirmed the ability of lobsters to accumulate extremely high amounts of PAH in their tissues. 14 references.

The combustion characteristics of refuse derived fuels using coke/waste tire

Energy Technology Data Exchange (ETDEWEB)

Park, M.H. [Dep. of Mechanical Eng., Samcheok Nat' l Univ., Samcheok (Korea); Shin, D.Y. [Research Center for Advanced Mineral Aggregate Composite Products, Kangwon Nat' l Univ., Chuncheon (Korea)

2005-07-01

Today every nation faces serious problems of energy supply. Reasonable technologies to make use of coal (including coke) can not only help the mining-related economy which is showing a downward trend but also may fit in with the governmental energy policy. In this research, we aim to supply heating systems in factories, homes, and farms with a substitute fuel by developing coke/waste tire compound fuel with high efficiency for rational use of energy and for recycling of industrial products. A coke/waste boiler was used for this experiment, and different kinds of fuel were experimented including coke, waste tire, coke/waste A and coke/waste B. Four kinds of exhaust gas were also sampled by a gas analyzer, including CO, CO{sub 2}, NO and NO{sub 2} at different temperatures. (orig.)

Hygiene of work in main shops of modern coking by-product industry. [USSR

Energy Technology Data Exchange (ETDEWEB)

Kapitul' skii, V B

1984-07-01

The hygiene of working conditions is evaluated and compared for coking by-product industry shops using modern technology and machines with those using obsolete equipment and methods. Most basic factors in contamination of atmosphere of coking, pitch-coking and metal-refining shops are coal and coke dust, carbon monoxide and polycyclic aromatic hydrocarbons, especially carcinogenic benzpyrene. Contamination of air of working zone is determined by details of technology: periodicity or continuity of industrial processes, use of improved equipment for smokeless injection of charge into stoves and of hermetic pipes to remove gas with hydraulically operated caps, position of machines in shops and in coal tar distillation removal of carcinogenic benzpyrene by sulfonation and aeration. In modernized shops of coking by-product industry, illness and loss of work capacity are significantly lower than in plants using obsolete methods and equipment. Measures are presented for hygienic improvement of working conditions; both methods to further increase efficiency of technological processes and methods to protect individual worker on job such as use of respirators, protective clothing, plexiglass shields, shampoos and skin creams. 14 references.

Demand outlook for sulfur and high-sulfur petroleum coke

Energy Technology Data Exchange (ETDEWEB)

Koshkarov, V.Ya.; Danil' yan, P.G.; Feotov, V.E.; Gimaev, R.N.; Koshkarova, M.E.; Sadykova, S.R.; Vodovichenko, N.S.

1980-01-01

The feasibility of using sulfur and high-sulfur petroleum coke fines in pyrometallurgical processes and also in the chemical and coal-tar chemical industry is examined. Results of industrial tests on briquetting fines of petroleum coke with a petroleum binder are presented. The feasibility of using the obtained briquets in shaft furnace smelting of oxidized nickel ores, production of anode stock, and also in the chemical industry are demonstrated.

Coal marketing manual 1986

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

This manual presents information for the use of marketers, consumers, analysts and investors. The information is presented in a series of tables and figures. Statistics are given for: Australian export tonnages and average export values for 1978-1985; international pig iron production 1976 to 1985; and international crude steel production 1979 to 1985. Trends in Australian export tonnages and prices of coal are reviewed. Details of international loading and discharge ports are given, together with a historical summary of shipping freight-rates since 1982. Long term contract prices for thermal and coking coal to Japan are tabulated. A review of coal and standards is given, together with Australian standards for coal and coke. A section on coal quality is included containing information on consumer coal quality preferences and Australian and Overseas coal brands and qualities. Finally an index is given of contact details of Australian and Overseas exporting companies, government departments, and the Australian Coal Association.

Characterization of core-drilled cokes in a working blast furnace

Energy Technology Data Exchange (ETDEWEB)

Shanning Dong; Nigel Paterson; Denis R. Dugwell; Rafael Kandiyoti [Imperial College London, London (United Kingdom). Dept. of Chemical Engineering

2007-07-01

A batch of tuyere-level core-drilled cokes, taken from a blast furnace working with coal injection has been characterized using a battery of analytical techniques. These included size exclusion chromatography (SEC), FT-Raman Spectroscopy (FT-RS) and X-ray Powder Diffraction (XRD). SEC tests on NMP-extracts of cokes taken from zones where temperatures were ca. 1500{sup o}C, showed the presence of heavy soot-like material (ca. 107-108 u apparent mass). By contrast, cokes in higher temperature zones (ca. 2000{sup o}C), only gave small amounts of extractable material with up to ca. 105 u apparent mass. The presence of soot-like material indicated the conversion-unfavoured locations at the tuyere-level. FT-Raman spectra of NMP-extracted cokes varied: the area ratios of D (at 1288-1295cm{sup -1}) to G (at ca. 1596cm{sup -1}) bands decreased as the exposure temperature increased. The random (r) fractions decreased with increasing exposure temperature, whereas, the graphitic (G) fractions increased whilst the defect (D) fraction showed a more complex variation with temperature. The latter is a likely indicator of graphitization of tuyere-level cokes in the blast furnace. The Raman spectral results were validated by XRD analyses of the demineralised and NMP-extracted cokes. Raceway coke possessed the largest crystalline dimensions and closest inter-layer spacing because it had encountered highest temperatures as well as iron catalysis. The combination of SEC and Raman spectrometry on core-drill samples has provided information relevant for maintaining stable operation in a blast-furnace operating with coal injection. 13 refs., 7 figs., 6 tabs.

Residential conference on science in the use of coal

Energy Technology Data Exchange (ETDEWEB)

1958-01-01

The ''Residential Conference on Science in the Use of Coal'' was held in the Chemistry Department of the University of Sheffield on April 15-17, 1958. The proceedings have been published by the Institute of Fuel, 18 Devonshire Street, Portland Place, London, W.1, England. Sessions involved the physics and chemistry of coal, coal preparation and breakage, coal carbonization, coal and coke combustion and gasification and the reactivity of cokes and chars. Forty-three papers have been entered individually into EDB. (LTN)

Coal 95

International Nuclear Information System (INIS)

Sparre, C.

1995-01-01

The report deals with the use of coal and coke in Sweden during 1994. Some information about technology, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from Statistics Sweden have also been used.The use of steam coal for heating purposes has been unchanged during 1994 at a level of 1 Mtons. The production in the cogeneration plants has been constant, but has increased for electricity production. The minor plants have increased their use of forest fuels. The use of steam coal will probably go down in the next years both for heat and cogeneration plants. During the top year 1987 coal was used in 18 hot water and 11 cogeneration plants. 1994 these figures are 3 and 12. Taxes and environmental reasons explain this trend. The use of steam coal in industry has been constant at the level 0.7 Mtons. The import of metallurgical coal in 1993 was 1.6 Mtons, like 1992. Import of 0.3 Mtons of coke gives the total consumption of coke in industry as 1.5 Mtons. the average price of steam coal imported to Sweden was 317 SEK/ton, 3% higher than 1993. All Swedish plants meet their emission limit of dust, SO 2 and NO x as given by county administrations or concession boards. The cogeneration plants all have some SO 2 removal system. The biggest cogeneration plant (Vaesteraas) has recently invested in a SCR NO x cleaning system. Most other plants use low NO x burners or SNR injection systems based on ammonia or urea. 2 figs, 13 tabs

Production of Schwarzmoeller briquets from weakly caking black coal and iron ore

Energy Technology Data Exchange (ETDEWEB)

Naundorf, W.

1986-01-01

Laboratory production is explained of coal and iron ore briquets suitable for metallurgy, using type 33 weakly caking black coal, iron ore concentrates from 3 Soviet mines and sulfite lye as binder. Coal and ore were finely ground to 0.3/0.0 mm grain size, briquetted at high pressure of 150 MPa and at 80 C temperature. The sulfite lye binder content ranged from 4 to 10% in the briquet mixture. Briquets were thermally treated up to 1000 C; the resulting coke lumps (Schwarzmoeller briquets) were analyzed for compression and abrasion strength. Detailed graphs of briquet and coke lump quality parameters are provided. The study shows that high quality metallurgical coke lumps are obtained by briquetting mixtures of black coal and iron ore in a mixture of about 70:30 with 4 to 9% addition of sulfite binder. Compression strength of coke lumps exceeded 35 MPa. The minimum black coal-iron ore mass relation for producing metallurgical coke lumps was 30:70 using 2 types of iron ore concentrates. The influence of adding limestone to the briquetting mixture and of coking conditions resembling the horizontal chamber oven process is also investigated. 5 references.

Effluents of toxic and corrosion-active components at coke-oven gas combustion

International Nuclear Information System (INIS)

Mikhajlov, G.S.; Afanas'ev, Yu.O.; Plotnikov, V.A.; Iskhakov, Kh.A.; Tikhov, S.D.; Gaus, A.I.; Nagibin, P.D.

1996-01-01

Various modes of coke-coal gas combustion are studied and dependence of concentration of nitrogen sulfur oxides and carbon monoxides originating in smoke gases on the air excess delivered to the combustion chamber is determined. The lowest summary releases of hazardous substances are achieved by the excess air coefficients α > 1.2 relative to modes of coke-coal gas combustion with smoke gases recirculation. The quantity of sulfur does not depend on the mode of fuel combustion and is determined by the total sulfur content in the fuel. To prevent the corrosion of low-temperature heat exchange surfaces it is necessary to heat up the feed-water up to the temperature exceeding the temperature of the coal gases dew point by 10-15 deg C. 10 refs

Coking processes

Energy Technology Data Exchange (ETDEWEB)

Rollason, A

1913-09-01

In the production of light hydrocarbon oils from coals, cannels, or shales which are high in oxygen, from 3 to 5% of limestone or other suitable carbonate is added to the coking-charge. The carbonate added is proportionate to the oxygen contained in the coal etc. The charge is slowly heated up to a temperature of about 500/sup 0/C., water is driven off between 85 and 105/sup 0/C., and carbon dioxide is evolved at a low temperature and retards the evolution of combustible gases until a temperature between 130 and 175/sup 0/C., is reached. Upon formation of the endothermic hydrocarbons, the temperature of the charge becomes lowered, a large volume of light oils of the benzol series is produced, and an increased yield of ammonia is obtained, leaving the carbon in graphitic form.

Impact on surface water quality due to coke oven effluents

International Nuclear Information System (INIS)

Ghose, M.K.; Roy, S.

1994-01-01

Large quantities of water are used for the quenching of hot coke and also for washing the gas produced from the coke ovens. Liquid effluents thus generated are highly polluted and are being discharged into the river Damodar without proper treatment. Four coke plants of Bharat Coking Coal Ltd.(BCCL) have been surveyed for characterization and to assess the impact on surface water quality. About 175-200 kilolitres of waste water is being generated per day by each of the coke plants. The concentration of CO, BOD, COD, TSS, phenol and cyanide in each of the coke plants were found to exceed the limits specified by pollution control board. Ammonia, oil and grease and TDS were found to be 19.33 mg/l, 7.81 mg/l, 1027.75 mg/l respectively. Types of samples collected, sampling frequencies, sample preservation and the results obtained have been discussed. (author). 6 refs., 1 tab., 1 fig

Study on trace and rare earth elements in Indonesian oil sands

Energy Technology Data Exchange (ETDEWEB)

Bai, Jing-ru; Wang, Qing; Liu, Hong-peng; Bai, Zhang [Northeast Dianli Univ., Jilin (China). Engineering Research Centre

2013-07-01

Major, trace elements and rare earth and mineral composition of the oil sand samples (ST1, ST2, ST3) and the oil sand retorting residue (semi-coke: SC1, SC2, SC3) from Indonesian were determined by XFS, ICP-MS and XRD methods. The trace elements content in oil sand is pretty much the same thing in Earth's Clarke value. The trace element is abundantly in earth's Clarke, in oil sand yet, for Ti, Mn, Ba, Sr, but these elements are lower enrichment. However, the Cr (EF = 16.8) and Mo (EF = 11.8) are ''enrichment'' in ST1; the Ni (EF =10.5), Se (EF = 17.5), Sr (EF = 28.7), Mo (EF = 106.5), Sc (EF = 12.8) and U (EF = 43.2) are ''enrichment'' in ST2; the Se (EF = 12.6), Sr (EF = 18.4), Mo (EF = 47.5), and U (EF = 27.8) are ''enrichment'' in ST3. Calculations show that trace elements in sime-coke have lower evaporation rate during Fischer Assay. Trace elements in raw oil sand are so stable that trace elements can't move easily to other pyrolysis product but enrich to sime-coke. After retorting, more elements are EF > 10, such as B, V, Ni, As, Se, Sr, Mo, Hg, Cs and U. It is essential to take the pollution produced by trace elements in sime-coke during the sime-coke utilization into consideration. The REEs content had a high correlation with the ash in oil sand. The REE is closely related to terrigenous elastic rocks.

Petroleum Coke in the Urban Environment: A Review of Potential Health Effects

Directory of Open Access Journals (Sweden)

Joseph A. Caruso

2015-05-01

Full Text Available Petroleum coke, or petcoke, is a granular coal-like industrial by-product that is separated during the refinement of heavy crude oil. Recently, the processing of material from Canadian oil sands in U.S. refineries has led to the appearance of large petcoke piles adjacent to urban communities in Detroit and Chicago. The purpose of this literature review is to assess what is known about the effects of petcoke exposure on human health. Toxicological studies in animals indicate that dermal or inhalation petcoke exposure does not lead to a significant risk for cancer development or reproductive and developmental effects. However, pulmonary inflammation was observed in long-term inhalation exposure studies. Epidemiological studies in coke oven workers have shown increased risk for cancer and chronic obstructive pulmonary diseases, but these studies are confounded by multiple industrial exposures, most notably to polycyclic aromatic hydrocarbons that are generated during petcoke production. The main threat to urban populations in the vicinity of petcoke piles is most likely fugitive dust emissions in the form of fine particulate matter. More research is required to determine whether petcoke fine particulate matter causes or exacerbates disease, either alone or in conjunction with other environmental contaminants.

29 CFR 779.357 - May qualify as exempt 13(a)(2) establishments; classification of coal sales.

Science.gov (United States)

2010-07-01

... principal raw material, such as sales of coal for the production of coke, coal gas, coal tar, or electricity... production of coke, coal gas, coal tar, or electricity. This is distinguished from sales of coal for use in...; classification of coal sales. 779.357 Section 779.357 Labor Regulations Relating to Labor (Continued) WAGE AND...

Black coal. [Australia

Energy Technology Data Exchange (ETDEWEB)

Pratt, R

1973-01-01

Statistics are given for the Australian black coal industry for 1970-3 (production, value, employment, wages and salaries, productivity, trade, stocks, consumption, export contracts, exploration, etc.). In less detail, world coal trade is reviewed and coke production is mentioned briefly. (LTN )

Development of coal petrography applied in technical processes at the Bergbau-Forschung/DMT during the last 50 years

International Nuclear Information System (INIS)

Steller, Monika; Arendt, Paul; Kuehl, Helmut

2006-01-01

The paper deals with the activities of the Bergbau-Forschung Coal Petrography Laboratory in Essen (Germany), which, under the influence of Marie-Therese Mackowsky, developed into a stronghold of the industrial application of coal petrology. In 1979, the formerly independent Section for Mineralogy and Petrology was merged with the Chemistry Section. This synergy has widened the research limits and resulted in higher efficiency of projects being carried out within both units. Since 1990, after transforming Bergbau-Forschung into DMT GmbH, a worldwide competition within hard coal and hard coal-based coke markets, together with the switch of the industry towards alternative energy sources, have significantly lowered the importance of the domestic coal mining industry. This in turn resulted in reduction of coal research programs. However, it is stressed that, in spite of transformations of the applied coal petrology experienced during the past 50 years, some achievements are still as applicable as ever. Among them, the method of predicting coke strength using maceral analysis and coal types, published by Mackowsky and Simonis [Mackowsky, M.-Th., Simonis, W., 1969. Die Kennzeichnung von Kokskohlen fur die mathematische Beschreibung der Hochtemperaturverkokung im Horizontalkammerofen bei Schuttbetrieb durch Ergebnisse mikroskopischer Analysen. Gluckauf-Forschungshefte 30, 25-27], is still in use today. The second part of this paper presents some examples of coal petrography applications, which are still important in carbonization processes. Mackowsky discovered that the pyrolytic components were influencing the coke homogeneity in coke ovens and affected coke quality parameters such as CRI and CSR. These highly graphitic layers and lenses prevent gasification of the inner zones of coke lumps, thus lowering the reactivity of metallurgical coke. Moreover, it also seems possible to predict wall load and maximum internal gas pressure as to prevent coke ovens from damage

Development of coal petrography applied in technical processes at the Bergbau-Forschung/DMT during the last 50 years

Energy Technology Data Exchange (ETDEWEB)

Steller, Monika; Arendt, Paul; Kuehl, Helmut [Deutsche Montan Technologie GmbH ? Mining Service Division?Essen (Germany)

2006-06-06

The paper deals with the activities of the Bergbau-Forschung Coal Petrography Laboratory in Essen (Germany), which, under the influence of Marie-Therese Mackowsky, developed into a stronghold of the industrial application of coal petrology. In 1979, the formerly independent Section for Mineralogy and Petrology was merged with the Chemistry Section. This synergy has widened the research limits and resulted in higher efficiency of projects being carried out within both units. Since 1990, after transforming Bergbau-Forschung into DMT GmbH, a worldwide competition within hard coal and hard coal-based coke markets, together with the switch of the industry towards alternative energy sources, have significantly lowered the importance of the domestic coal mining industry. This in turn resulted in reduction of coal research programs. However, it is stressed that, in spite of transformations of the applied coal petrology experienced during the past 50 years, some achievements are still as applicable as ever. Among them, the method of predicting coke strength using maceral analysis and coal types, published by Mackowsky and Simonis [Mackowsky, M.-Th., Simonis, W., 1969. Die Kennzeichnung von Kokskohlen fur die mathematische Beschreibung der Hochtemperaturverkokung im Horizontalkammerofen bei Schuttbetrieb durch Ergebnisse mikroskopischer Analysen. Gluckauf-Forschungshefte 30, 25-27], is still in use today. The second part of this paper presents some examples of coal petrography applications, which are still important in carbonization processes. Mackowsky discovered that the pyrolytic components were influencing the coke homogeneity in coke ovens and affected coke quality parameters such as CRI and CSR. These highly graphitic layers and lenses prevent gasification of the inner zones of coke lumps, thus lowering the reactivity of metallurgical coke. Moreover, it also seems possible to predict wall load and maximum internal gas pressure as to prevent coke ovens from damage

Research of coal flash hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Zhu, Z.; Zhu, H.; Wu, Y.; Tang, L.; Cheng, L.; Xu, Z. [East China University of Science and Technology, Shanghai (China)

2001-02-01

Using x-ray photoelectron spectroscopy (XPS) analyses the organic sufur of seven different Chinese coals and their semi-cokes from flash hydropyrolysis were studied. The results showed that the organic sulfur in coal was alkyal sulfur and thiophene with the peak of XPS located in 163.1-163.5 eV and 164.1-164.5 eV. The relative thiophene content in coal increased with the coal rank. The type of organic sulfur in semi-coke in flash hydropyrolysis was generally thiophene species; its XPS peak also located in 164.1-164.5 eV, and was in accord with its corresponding coal. Total alkyl sulfur and some thiophene sulfur were removed during the flash hydropyrolysis process. The alkyl sulfur had very high activity in hydrogenation reaction. Flash hydropyrolysis was an important new clean-coal technique and had notable desulfurization effect. 13 refs., 2 figs., 4 tabs.

Utilization potentiality of coal as a reductant for the production of sponge iron. [5 refs

Energy Technology Data Exchange (ETDEWEB)

Mishra, H P

1976-10-01

With the ambitious plan of the Government of India to produce about 70 million tonnes of steel per annum towards the end of the century, the requirement of coal would be enormous. This calls for judicious planning and conservation of coal. Modern trend in steel plant practice is to use blast furnaces of capacity 10,000 to 12,000 t/day requiring superior quality coke of low ash content which will become scarce. Concerted efforts should be made to by-pass blast furnace technique by adopting direct reduction for the production of metallized iron ore, that is sponge iron, and using this as feed stock in electric furnaces. Experience has shown that the use of sponge iron as feed stock for electric arc furnaces instead of the scrap available from various fabrication and steel works results in better production of alloy steels. The use of non-coking coal as reductant for production of sponge iron will help conserve coking coal for bigger steel plants. In the solid state reduction process the technological design of the sponge iron plant has to be tailored to the type of feed stock to be used, particularly iron ore and coal. In India, non-coking coal is available at close proximity to the iron ore mines containing high grade iron ore. Planning for sponge iron, utilizing large reserves of non-coking coal as feed stock therefore has considerable potentiality. India has vast reserves of high grade iron ore and comparatively meager amount of coking coal. This calls for planning for sponge iron using non-coking coal as feed stock.

Coal -94

International Nuclear Information System (INIS)

Sparre, C.

1994-05-01

This report deals with use of coal and coke during 1993; information about techniques, environmental questions and markets are also given. Use of steamcoal for heating purposes has been reduced about 3 % during 1993 to 1,0 mill tons. This is the case especially for the heat generating boilers. Production in co-generation plants has been constant and has increased for electricity production. Minor plants have increased their use of forest fuels, LPG and NG. Use of steamcoal will probably go down in the immediate years both in heat generating and co-generating plants. Coal-based electricity has been imported from Denmark during 1993 corresponding to about 400 000 tons of coal, when several of our nuclear plants were stopped. Use of steamcoal in the industry has been constant at 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1993 was 1,6 mill tons like the year before. 1,2 mill tons coke were produced. Coke consumption in industry was 1,4 mill tons. 0,2 mill tons of coke were imported. Average price of steamcoal imported to Sweden in 1993 was 308 SEK/ton or 13 % higher than in 1992; this can be explained by the dollar price level increasing 34% in 1993. For the world, the average import price was 50,0 USD/ton, a decrease of 6 %. The coal market during 1993 was affected by less consumption in Europe, shut downs of European mines and decreasing prices. High freight price raises in Russia has affected the Russian export and the market in northern Europe. The prices have been stabilized recently. All Swedish plants meet emission limits of dust, SO 2 and NO x . Co-generation plants all have some sort of SO 2 -removal system; the wet-dry method is mostly used. A positive effect of the recently introduced NO x -duties is a 40% reduction

Development of direct observation aparatus of coal carbonization process by x-ray computerized tomography method

International Nuclear Information System (INIS)

Sakawa, Mitsuhiro; Shiraishi, Katsuhiko; Sakurai, Yoshihisa; Shimomura, Yasuto

1987-01-01

Coke production by chamber ovens has a long history and efforts are being continued to make the manufacturing process efficient and to preserve the environment. In this production by this method, however, it is hardly possible to obtain direct information during coal carbonization. Since the elements that compose coal and coke are carbon, hydrogen, oxygen, etc. and are similar to those of the human body, authors has developed a coke oven that permits the direct observation of the coal carbonization process using a soft X-ray computerized tomography (CT) apparatus used in medical treatment. The following phenomena can be observed as images by the coke oven for the CT method : 1) Changes in the bulk density of charge coal (including the difference in the water content), 2) Width of the plastic layer and movement of the plastic layer in the coke oven chamber, 3) Expansion and shrinkage of the charge in the coke oven chamber, 4) Initiation and growth of cracks. (author)

Catalytic effect of lignite ash on steam gasification of oil sand coke

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Palmer, A.

1986-06-16

Steam gasification of Suncor and Syncrude cokes was carried out in the presence of ash obtained after burning Onakawana lignite. Catalytic effects of the ash were evident at 930 C whereas at 830 C little effect was observed. These observations were attributed to the combined actions of Ca- and Fe-containing species in the ash, in which the former neutralized the sulfur in the cokes to prevent poisoning of Fe oxides. 5 tabs., 5 figs., 15 refs.

Tales from a distant swamp: Petrological and paleobotanical clues for the origin of the sand coal lithotype (Mississippian, Valley Fields, Virginia)

Science.gov (United States)

Hower, J.C.; O'Keefe, J.M.K.; Eble, C.F.

2008-01-01

Tournasian (Mississippian) Price Formation semianthracites (Rmax = 2.40%) in the Valley Fields of southwestern Virginia contain a lithotype described in an early-20th-century report as a "sand" coal. The Center for Applied Energy Research inherited a collection of coals containing sand coal specimens, making it possible to study the lithotype from the long-closed mines. The sand coal consists of rounded quartz sand and maceral assemblages (secretinite, corpogelinite, and rounded collotelinite) along with banded collotelinite, vitrodetrinite, and inertodetrinite assemblages. The association of rounded macerals and similar-size quartz grains suggests transport. Oxidation rims surrounding the rounded collotelinite provides further evidence for transport. Due to the semianthracite rank, palynology could not be performed. Stratigraphic evidence indicates that the Lepidodendropsis flora would have been the dominant mire vegetation. Pteridosperms in this assemblage could have contributed resin rodlets, subsequently metamorphosed to collogelinite or secretinite. While a resin rodlet origin is an intriguing possibility for the origin of the rounded macerals (at least some of the rounded maceral, the rounded collotelinite clearly has a different origin), we cannot definitively prove this origin. ?? 2008 Elsevier B.V. All rights reserved.

The life cycle greenhouse gas emissions implications of power and hydrogen production for oil sands operations

International Nuclear Information System (INIS)

McKellar, J.M.; Bergerson, J.A.; MacLean, H.L.

2009-01-01

'Full text:' The Alberta Oil Sands represent a major economic opportunity for Canada, but the industry is also a significant source of greenhouse gas (GHG) emissions. One of the sources of these emissions is the use of natural gas for the production of electricity, steam and hydrogen. Due to concerns around resource availability and price volatility, there has been considerable discussion regarding the potential replacement of natural gas with an alternative fuel. While some of the options are non-fossil and could potentially reduce GHG emissions (e.g., nuclear, geothermal, biomass), others have the potential to increase emissions. A comparative life cycle assessment was completed to investigate the relative GHG emissions, energy consumption and financial implications of replacing natural gas with coal, coke, asphaltenes or bitumen for the supply of electricity, steam and hydrogen to oil sands operations. The potential use of carbon capture and storage (CCS) was also investigated as a means of reducing GHG emissions. Preliminary results indicate that, without CCS, the natural gas systems currently in use have lower life cycle GHG emissions than gasification systems using any of the alternative fuels analysed. However, when CCS is implemented in both the coke gasification and natural gas systems, the coke systems have lower GHG emissions and financial costs than the natural gas systems (assuming a 30-year project life and a natural gas price of 6.5 USD/gigajoule). The use of CCS does impose a financial penalty though, indicating that it is unlikely to be implemented without some financial incentive. While this study has limitations and uncertainties, the preliminary results indicate that although the GHG emissions of oil sands development pose a challenge to Canada, there are opportunities available for their abatement. (author)

Possibilities of increasing coal charge density by adding fuel oil

Directory of Open Access Journals (Sweden)

M. Fröhlichová

2010-01-01

Full Text Available The requirement of all coke-making facilities is to achieve the highest possible production of high quality coke from a chamber. It can be achieved by filling the effective capacity of the chamber with the highest possible amount of coal. One of the possibilities of meeting this requirement is to increase the charge density in the coke chamber. In case of a coke battery operating on bulk coal there are many methods to increase the charge density including the use of wetting agents in the charge. This article presents the results of the laboratory experiments aiming at the increase of the charge density using fuel oil as a wetting agent. The experiments were carried out by means of the Pitin’s device using 3 coal charges with various granularity composition and moisture content of 7, 8, 9 and 10 %.

Hard coal; Steinkohle

Energy Technology Data Exchange (ETDEWEB)

Loo, Kai van de; Sitte, Andreas-Peter [Gesamtverband Steinkohle e.V., Herne (Germany)

2013-04-01

The year 2012 benefited from a growth of the consumption of hard coal at the national level as well as at the international level. Worldwide, the hard coal still is the number one energy source for power generation. This leads to an increasing demand for power plant coal. In this year, the conversion of hard coal into electricity also increases in this year. In contrast to this, the demand for coking coal as well as for coke of the steel industry is still declining depending on the market conditions. The enhanced utilization of coal for the domestic power generation is due to the reduction of the nuclear power from a relatively bad year for wind power as well as reduced import prices and low CO{sub 2} prices. Both justify a significant price advantage for coal in comparison to the utilisation of natural gas in power plants. This was mainly due to the price erosion of the inexpensive US coal which partly was replaced by the expansion of shale gas on the domestic market. As a result of this, the inexpensive US coal looked for an outlet for sales in Europe. The domestic hard coal has continued the process of adaptation and phase-out as scheduled. Two further hard coal mines were decommissioned in the year 2012. RAG Aktiengesellschaft (Herne, Federal Republic of Germany) running the hard coal mining in this country begins with the preparations for the activities after the time of mining.

Rational use of coal from the Kansk-Achinsk basin

Energy Technology Data Exchange (ETDEWEB)

Andreeva, I.A.; Antonova, L.I.; Khapaeva, O.K.

1983-02-01

Brown coal from the Kansk-Achinsk basin will be used as fuel in power plants as well as raw material for production of coke and smokeless fuel. Production of semicoke should amount to 9 Mt/year, 4 Mt of which will be smokeless fuel. A method for coking brown coal from the Kansk-Achinsk basin developed by the MGI Institute is described: semicoke mixed with coal tar used as a binder and polymers (from 2 to 4%), playing the role of a modifier, is carbonized at 850 to 900 C. Briquets produced from brown coal semicoke are characterized by a high carbon content up to 94.7%, emission of volatile matter down to 9.0%, ash content of 8.8% and good mechanical properties. A method for production of coke for removal of sulfurous anhydride from coal power plant emission is described: semicoke is granulated using the heavy fraction of coal tar formed during semicoking, granules are carbonized and activated at a temperature of 900 C. Volume of mesopores and micropores in coke amounts to 0.4 cm/sup 3//g and the specific surface is 28 to 600 m/sup 2//g (with a combustion loss of of 20 to 24 %). This sorbent is also used as carrier for catalysts in metallurgy and for collecting and recovering solvents from industrial gases.

Production of fine coke in a hearth-type furnace (Report on ECSC contract 7720-EB/108)

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

A balance was established for the hearth-type coking oven and waste heat boiler system. Tests concerning the operational safety showed that, in the case of breakdowns, the oven and waste heat boiler could be shut down without any danger. The quality of the brown coal fine coke produced, could be improved by optimizing the heights of the layer in the hearth-type, the degasification temperature of the oven, and the operation of the coke cooling system. Higher coking temperature caused a lower grain disintegration and lower abrasion rates. The range of size of coke production was enlarged to lump size by additional feeding of 2-inch briquettes to the coking oven.

Steel story founded on coal

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

Paper reports on an iron and steel plant in New Zealand which uses non-coking subbituminuous coal to produce the sponge iron. The transport of the ironsand and the coal to the site and the operation of the kiln in which the ironsand is reduced by the coal is described.

Physico-chemical treatment of coke plant effluents for control of water pollution in India

Energy Technology Data Exchange (ETDEWEB)

Ghose, M.K. [Indian School of Mines, Dhanbad (India). Center of Mining Environmental

2002-01-01

Coal carbonizing industries in India are important and are growing every year. Large quantities of liquid effluents produced in this industry contain a large amount of suspended solids, high biochemical oxygen demand (BOD), chemical oxygen demand (COD), phenols, ammonia and other toxic substances, which are causing serious surface water pollution in the area. There is a large number of coke plants in the vicinity of Jharia Coal Field (JCF). The working principle of a coke plant and the effluents produced is described. One large coke plant was chosen to evaluate characteristics of the effluent and to suggest a proper treatment method. Present effluent treatment system was found to be inadequate and a large quantity of a very good quality coke breeze is being lost, which is also causing siltation on the riverbed in addition to surface water pollution. Physico-chemical treatment has been considered as a suitable option for the treatment of coke plant effluents. A scheme has been proposed for the treatment, which can be suitably adopted for the recycling, reuse or safe disposal of the treated effluent. Various unit process and unit operations are discussed. The process may be useful on industrial scale for various sites so as to maintain a clean environment.

Characterization of tuyere-level core-drill coke samples from blast furnace operation

Energy Technology Data Exchange (ETDEWEB)

S. Dong; N. Paterson; S.G. Kazarian; D.R. Dugwell; R. Kandiyoti [Imperial College London, London (United Kingdom). Department of Chemical Engineering

2007-12-15

A suite of tuyere-level coke samples have been withdrawn from a working blast furnace during coal injection, using the core-drilling technique. The samples have been characterized by size exclusion chromatography (SEC), Fourier transform Raman spectroscopy (FT-RS), and X-ray powder diffraction (XRD) spectroscopy. The 1-methyl-2-pyrrolidinone (NMP) extracts of the cokes sampled from the 'bosh', the rear of the 'bird's nest', and the 'dead man' zones were found by SEC to contain heavy soot-like materials (ca. 10{sup 7}-10{sup 8} apparent mass units). In contrast, NMP extracts of cokes taken from the raceway and the front of the 'bird's nest' only contained a small amount of material of relatively lower apparent molecular mass (up to ca. 10{sup 5} u). Since the feed coke contained no materials extractable by the present method, the soot-like materials are thought to have formed during the reactions of volatile matter released from the injectant coal, probably via dehydrogenation and repolymerization of the tars. The Raman spectra of the NMP-extracted core-drilled coke samples showed variations reflecting their temperature histories. Area ratios of D-band to G-band decreased as the exposure temperature increased, while intensity ratios of D to G band and those of 2D to G bands increased with temperature. The graphitic (G), defect (D), and random (R) fractions of the carbon structure of the cokes were also derived from the Raman spectra. The R fractions decreased with increasing temperature, whereas G fractions increased, while the D fractions showed a more complex variation with temperature. These data appear to give clues regarding the graphitization mechanism of tuyere-level cokes in the blast furnace. 41 refs., 9 figs., 6 tabs.

Influence of rubber granulate in the coal blend on important process parameters of the coking plant

Energy Technology Data Exchange (ETDEWEB)

A. Winter; K. Pilz; A. Gahleitner; G. Woisetschlaeger; Monika Friedl [Voestalpine Stahl GmbH (Germany)

2004-07-01

The talk is outlined in a series of 14 slides/overheads. It discusses the use of scrapped tires in coking plant and traces the amount of zinc present in every product of the coking plant, blast furnaces and sintering plant - coke, coke breeze, sinter and waste water produced.

Studies on classifying Indian coals. Part II. A new system for grading and pricing

Energy Technology Data Exchange (ETDEWEB)

Tumuluri, S.G.; Shrikhande, S.K.; Rao, S.K.; Haque, R.

1985-07-01

The new system is self-complete through grading to pricing. It grades non-coking coal by moisture and ash contents. Coking coal is graded by GKLT coke type and ash content. Volatile matter content is used as a supporting indexer, where necessary. Through the grade data, a coal is evaluated into a single numeral which depicts the coaly matter content and its nature or effectiveness. This value, called effective coaly matter, is converted to a relative rupee value or price index/price. Pragmatics and versatility of the system are discussed.

Coal world market

International Nuclear Information System (INIS)

Anon.

1996-01-01

A brief analysis of major tendencies in the world market of coal is presented. It is pointed out that recent years, by and large, were favourable for the development of the world coal industry. Prices for coal (both for power-grade and coking one) in 1995 after many years of depressive state increased by nearly 20 % and reached a maximum of the last decade. International coal trading continues to grow and the tendency may persist in the mext two years

Copyrolysis of coal with coke-oven gas. III. Analysis of tar

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Sun, C.; Li, B.; Liu, Z. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion, Institute of Coal Chemistry

1998-02-01

Tars from copyrolysis of Xianfeng lignite with coke-oven gas (COG) at different pressures (0.1-5 MPa) and heating rates (5-25{degree}C/min) to a final temperature of 650{degree}C were analyzed and compared with hydropyrolysis under the same H{sub 2} partial pressure. The results indicated that high contents of BTX, PCX and naphthalene were found in the tar from copyrolysis of Xianfeng lignite with COG. Pressure and heating rate have important effects on tar yields and the contents of BTX, PCX and naphthalene in oil. Increasing pressure and decreasing heating rate enhance the tar yields and result in high yields of BTX and PCX. When compared with hydropyrolysis under the same H{sub 2} partial pressure, the tar yield increases by 1.2 times and the yields of BTX, PCX and naphthalene by about 1.6, 1.3 and 1.6 times, respectively. At the same total pressure (3MPa), the yields of BTX and naphthalene from copyrolysis are equal to those from hydropyrolysis. The results reveal that other components in COG, such as methane, carbon monoxide etc., are of importance for pyrolysis behaviour of coal under COG and improvement of oil qualities. 5 refs., 5 figs., 2 tabs.

The year-book of the Coke Oven Managers' Association 2008

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

The 89th volume of the Year Book outlines activities of the Coke Oven Managers' Association throughout 2008 and reproduces transactions presented to the industry through its various sections. It includes lists of Council and Committee members and representation on committees and past presidents, and a full list of members. Reports of Council 2006-7 and of the annual general meeting 2007 are included. The Presidential address by A. Moore is about his experiences at Redcar Coke Ovens. Carbonisation and briquetting works in the United Kingdom, Koppers carbon materials and chemical works in the UK and Europe, European coking plants, their addresses and managers are listed. Six transactions are abstracted separately on the Coal Abstracts database.

Crack coke in layer heat transfer analysis; Kiretsu no shinten wo tomonau kokusu sonai dennetsu kaiseki

Energy Technology Data Exchange (ETDEWEB)

Aoki, Hideyuki [Tohoku University, Miyagi (Japan)

1999-03-05

The research method heat transfer process by physical change of the coke by heat transfer from furnace wall in the retorting of coal seam filled in coke oven and flow of the gas is very complicated chamber oven style, and it does not become clear. For the purpose of the elucidation of in layer crack generation and progress mechanism, he is (1) The expansion of the softening cohesive layer. (2) Programming rate dependence of the heat. Mechanical property value on coal seam and semi- coke layer in the retorting. (3) The creep property of softening cohesive layer and semi- coke layer. (4) The setting of crack growth condition of stress intensity factor in crack tip and fracture property value of the coke by the comparison. (5) By considering the radiative heat transfer in the crack, coke in layer thermal stress analysis was carried out. The validity of these analytical result it was confirmed by the comparison with the experimental result of crack growth. Deformation behavior in the small dry distillation furnace, and crack growth mechanism in the coke layer became clear, and the prediction of the stress as micro-crack cause of generation of heating surface side coke surface and inside became possible. The numerical analysis method of the above crack growth mechanism greatly contributes to the prediction of dry distillation heating requirement and grain size of coke lump which is an index to the coke quality. Heat on material process which is accompanied by the solidification. Contraction from the softening and material migration phenomenon have been clarified by the creative research method, while this research is directly useful for energy saving of pig ironmaking process of becoming one of the ringleaders of the CO{sub 2} generation. (translated by NEDO)

Defining geographic coal markets using price data and shipments data

International Nuclear Information System (INIS)

Waarell, Linda

2005-01-01

Given the importance of coal in world energy supply an analysis of the relevant geographic market is essential for consumers, producers, as well as for competition policy. The purpose of this paper is to define the relevant economic market for steam and coking coal, and to test the hypothesis of single world markets for these coal products. Methodologically the paper relies on two different tests for defining markets, using both shipments data and price data. The results from both methods point in the same direction. In the case of coking coal the results indicate that the market is essentially global in scope, and also that the market has become more integrated over time. The results for steam coal show that the market is more regional in scope, and there exist no clear tendencies of increased integration over time. One policy implication of the finding that the steam coal market is more regional in scope, and thus that the market boundary is smaller than if the market would have been international, is that a merger and acquisition in this market likely would have been of a more concern for antitrust authorities than the same activity on the coking coal market

Coal princes on the world market

International Nuclear Information System (INIS)

1997-01-01

The prices on fuel and coking coals on the world market are presented. The data on specific combustion heat content of volatile substances, sulfur and ash content of the corresponding types of coals are also given

Coal 95; Kol - 95

Energy Technology Data Exchange (ETDEWEB)

Sparre, C

1996-12-31

The report deals with the use of coal and coke in Sweden during 1994. Some information about technology, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from Statistics Sweden have also been used.The use of steam coal for heating purposes has been unchanged during 1994 at a level of 1 Mtons. The production in the cogeneration plants has been constant, but has increased for electricity production. The minor plants have increased their use of forest fuels. The use of steam coal will probably go down in the next years both for heat and cogeneration plants. During the top year 1987 coal was used in 18 hot water and 11 cogeneration plants. 1994 these figures are 3 and 12. Taxes and environmental reasons explain this trend. The use of steam coal in industry has been constant at the level 0.7 Mtons. The import of metallurgical coal in 1993 was 1.6 Mtons, like 1992. Import of 0.3 Mtons of coke gives the total consumption of coke in industry as 1.5 Mtons. the average price of steam coal imported to Sweden was 317 SEK/ton, 3% higher than 1993. All Swedish plants meet their emission limit of dust, SO{sub 2} and NO{sub x} as given by county administrations or concession boards. The cogeneration plants all have some SO{sub 2} removal system. The biggest cogeneration plant (Vaesteraas) has recently invested in a SCR NO{sub x} cleaning system. Most other plants use low NO{sub x} burners or SNR injection systems based on ammonia or urea. 2 figs, 13 tabs.

Retort for coking peat, brown coal, bituminous shale, etc

Energy Technology Data Exchange (ETDEWEB)

1902-05-14

The retort leads the gases and vapors into the coking chamber, between the inside heater and the outer heating shaft-wall. Over-lapping, double-faced acting rings are arranged, over which the charge in two or more separate vertical layers is transported.

An update on blast furnace granular coal injection

Energy Technology Data Exchange (ETDEWEB)

Hill, D.G. [Bethlehem Steel Corp., Burns Harbor, IN (United States); Strayer, T.J.; Bouman, R.W. [Bethlehem Steel Corp., PA (United States)

1997-12-31

A blast furnace coal injection system has been constructed and is being used on the furnace at the Burns Harbor Division of Bethlehem Steel. The injection system was designed to deliver both granular (coarse) and pulverized (fine) coal. Construction was completed on schedule in early 1995. Coal injection rates on the two Burns Harbor furnaces were increased throughout 1995 and was over 200 lbs/ton on C furnace in September. The injection rate on C furnace reached 270 lbs/ton by mid-1996. A comparison of high volatile and low volatile coals as injectants shows that low volatile coal replaces more coke and results in a better blast furnace operation. The replacement ratio with low volatile coal is 0.96 lbs coke per pound of coal. A major conclusion of the work to date is that granular coal injection performs very well in large blast furnaces. Future testing will include a processed sub-bituminous coal, a high ash coal and a direct comparison of granular versus pulverized coal injection.

Heat input control in coke ovens battery using artificial intelligence

Energy Technology Data Exchange (ETDEWEB)

Kumar, R.; Kannan, C.; Sistla, S.; Kumar, D. [Tata Steel, Jamshedpur (India)

2005-07-01

Controlled heating is very essential for producing coke with certain desired properties. Controlled heating involves controlling the heat input into the battery dynamically depending on the various process parameters like current battery temperature, the set point of battery temperature, moisture in coal, ambient temperature, coal fineness, cake breakage etc. An artificial intelligence (AI) based heat input control has been developed in which currently some of the above mentioned process parameters are considered and used for calculating the pause time which is applied between reversal during the heating process. The AI based model currently considers 3 input variables, temperature deviation history, current deviation of the battery temperature from the target temperature and the actual heat input into the battery. Work is in progress to control the standard deviation of coke end temperature using this model. The new system which has been developed in-house has replaced Hoogovens supplied model. 7 figs.

Study on standard coal preparation plant for coking coal in Jharia Coalfield

Energy Technology Data Exchange (ETDEWEB)

Winiewski, J; Sarkar, G G

1975-10-01

The proposed standardization of coal preparation plant will be based on three standard types of crushing station, a standard jig washery or cyclone washery, and three standard types of slurry water treatment section. Some large installations, and some existing washeries after modification, may incorporate heavy media baths for coarse coal and jigs for slack coal, where coal is easy or moderately easy to wash. Flow sheets are given for the standard types of crushing plant, washery, and slurry water circuit. The storage of raw coal and saleable products is briefly discussed.

The year-book of the Coke Oven Managers' Association 2006

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

The 87th volume of the Year Book outlines activities of the Coke Oven Managers' Association throughout 2006 and reproduces transactions presented to the industry through its various sections. It includes lists of Council and Committee members and representation on committees and past presidents, and a full list of members. Reports of Council 2004-5 and of the annual general meeting 2005 are included. The Presidential address by M. Gore is on the last five years of Monckton Coke and Chemical Company. Carbonisation and briquetting works in the United Kingdom, Koppers carbon materials and chemical works in the UK and Europe, European coking plants, their addresses and managers are listed. Seven transactions are abstracted separately on the Coal Abstracts database.

Reactivity of North Bohemian coals in coprocessing of coal/oil mixtures

Energy Technology Data Exchange (ETDEWEB)

Sebor, G.; Cerny, J.; Maxa, D.; Blazek, J. [Inst. of Chemical Technology, Prague (Czechoslovakia); Sykorova, I. [Inst. of Rock Structure and Mechanics, Prague (Czechoslovakia)

1995-12-01

Autoclave experiments with North Bohemian coal were done in order to evaluate their reactivity in coprocessing with petroleum vacuum residue, Selected coals were comprehensively characterized by using a number of analytical methods. While the coals were of similar geological origin, some of their characteristics differed largely from one coal to another. Despite the differences in physical and chemical structure, the coals provided very similar yields of desired reaction products. The yields of a heavy non- distillable fraction and/or an insoluble solid residue were, under experimental conditions, largely affected by retrogressive reactions (coking). The insoluble solid fractions were examined microscopically under polarized light.

Centrifuge treatment of coal tar

Energy Technology Data Exchange (ETDEWEB)

L.A. Kazak; V.Z. Kaidalov; L.F. Syrova; O.S. Miroshnichenko; A.S. Minakov [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

2009-07-15

New technology is required for the removal of water and heavy fractions from regular coal tar. Centrifuges offer the best option. Purification of coal tar by means of centrifuges at OAO NLMK permits the production of pitch coke or electrode pitch that complies with current standards.

ECONOMIC MODEL AND TOOLS OF THE AIR PROTECTION MANAGEMENT BASED ON THE EXAMPLE OF A COKING PLANT

Directory of Open Access Journals (Sweden)

Danuta Hilse

2014-10-01

Full Text Available Legal-economic models of the air protection management at the Polish industrial plants, which take into account the regulations of the Act on “Environment protection law”, are far from being perfect. It is particularly noticeable in the coking industry where chargeable pollutions are chosen selectively, and unitary rates of emission charges are agreed at random. Tax deductions are not granted either to producers of fuel coke for reduction of pollutants emission in municipal-housing management after replacing coal with fuel coke. The proposed new economic model of the air protection management at coking plants eliminates the existing shortcomings.

Denitrification of coking wastewater with micro-electrolysis.

Science.gov (United States)

Lv, Yanli; Wang, Yanqiu; Shan, Mingjun; Shen, Xue; Su, Ying

2011-06-01

The denitrification for the coking wastewater was conducted by means of original battery principle with Fe-C micro-electrolysis. Fe-C serves as positive and negative electrodes, by which N02(-)-N and TN were reduced to nitrogen, and then the purpose of denitrifieation for coking wastewater was realized. The influences of pH value, carbon particle size, Fe/C ratio (mass ratio), reaction time and coagulation pH value on removal rate of N02(-)-N and TN were investigated. Coking wastewater originated from Jiamusi Coal Chemistry Engineering Company. The optimum conditions of treatment were as follows: the initial pH was 3.0, the dosage of Fe 73.5 g/L, reaction time 70 min, mass ratio of Fe/C ratio 1.0:1.3, coagulation pH 9.0 and sedimentation time 40 min. Under those conditions, nitrogen removal efficiencies of N02(-)-N and TN were beyond 50% and 45%, respectively. Copyright © 2011 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

The Czech base of hard coal, problems, possibilities for utilization

International Nuclear Information System (INIS)

Cermak, T.; Roubicek, V.

1993-01-01

The Czech coal and power engineering base is in a deep restructuring period now. The basic problems represents the changeover from the system of the centrally planned state economy to the market model of the energy resources mining, production and consumption. The Czech economy will have to face to up to now unknown competitive forces on the coal market in Europe where American, Canadian, Australian and South African coals compete. The paper discusses historical aspects of the development of the coal mining industry in the Czechoslavakia, the present coal preparation techniques for coking coals, the coking industry, and the utilization of brown coal. How to utilize the domestic coal base and coal generally is closely connected with the global restructuralization of the Czech economy. The most difficult step of this process is undoubtedly the adaptation of the Czech fuel and energy base to the market economy conditions

Effective pretreatment of coal for briquetting

Energy Technology Data Exchange (ETDEWEB)

Sunami, Y; Nishioka, K; Sugimoto, Y

1980-01-01

The pretreatment of coal for briquetting is considered in an attempt to improve the quality of the briquets produced. Crushing of coal to obtain a size distribution suitable for close packing was found to be effective in improving coking properties while drying of coal was found to be effective in increasing briquet density. (In Japanese)

Role of non-ferrous coal minerals and by-product metallic wastes in coal liquefaction. Technical progress report, September 1, 1980-November 30, 1980

Energy Technology Data Exchange (ETDEWEB)

Garg, D.; Givens, E.N.; Schweighardt, F.K.; Curtis, C.W.; Guin, J.A.; Shridharani, K.; Huang, W.J.

1981-02-01

The effects of minerals and inexpensive ores or by-products (pyrites, red mud, flue dust, speculites, zinc sulfides, calcium oxide, dolomites, mica, molybdenite) in catalysing coal liquefaction or the hydrogenation of process solvents was studied with different cokes and solvents. Improved results were obtained in several cokes and th results are given in terms of oil fields, hydrogen consumption, desulfurization of SRC, etc. The addition of pyrite resulted in increased production of oils and increased conversion of coal; however, the effects varied from coal to coal. Dolomite, mica and molybdenite had insignificant catalytic activity. The reduction of pyrite, Fe/sub 2/O/sub 3/ and Fe/sub 3/O/sub 4/ at process conditions was studied. (LTN)

Computer-aided planning of brown coal seam mining in regard to coal quality

Energy Technology Data Exchange (ETDEWEB)

Ciesielski, R.; Lehmann, A.; Rabe, H.; Richter, S.

1988-09-01

Discusses features of the geologic SORVER software developed at the Freiberg Fuel Institute, GDR. The program processes geologic data from exploratory wells, petrographic characteristics of a coal seam model, technological mining parameters and coal quality requirements of consumers. Brown coal reserves of coking coal, gasification coal, briquetting coal and steam coal are calculated. Vertical seam profiles and maps of seam horizon isolines can be plotted using the program. Coal quality reserves along the surface of mine benches, mining block widths and lengths for excavators, maximum possible production of individual coal qualities by selective mining, and coal quality losses due to mining procedures are determined. The program is regarded as a means of utilizing deposit reserves more efficiently. 5 refs.

High-BTU gas production from tar-bearing hot coke oven gas over iron catalyst

Energy Technology Data Exchange (ETDEWEB)

L.Y. Li; K. Morishita; T. Takarada [Gunma University, Gunma (Japan). Department of Biological and Chemical Engineering

2005-07-01

To utilize the tar-bearing hot coke oven gas (the by-product of coke making process) more effectively, a process was developed by converting the hot coke oven gas into a methane rich high-BTU gas over iron-bearing catalysts. The catalytic behaviour of Indonesian limonite ore was mainly discussed. For a reference, a conventional nickel catalyst (Ni/Al{sub 2}O{sub 3}) was employed. Laboratory scale tests were carried out in a two-stage fixed-bed reactor at ambient pressure. A bituminous coal sample was heated at first stage, the volatiles was carried by feed gas and decomposed at second stage. The limonite promoted hydropyrolysis of coal volatiles similar to Ni/Al{sub 2}O{sub 3} catalyst. High yields of total product gas and methane were obtained at 50 vol.% hydrogen atmosphere with a feed gas of 60 ml min{sup -1} hydrogen and 60 ml min{sup -1} nitrogen. After experiments, hydrocarbons heavier than ethane were not observed. Also that, carbon balance was more than 99.8% in coal char, product gases and carbon deposits. It was considered that coal volatiles converted into light gases and carbon almost completely in catalyst bed. Yields of product gas and methane depended upon catalytic temperature. At 923 K, the maximum yield of product gas was achieved at 74.3% for limonite catalyst on carbon balance with methane 83.2 vol.% of the carbonaceous gas products. Comparing with limonite, Fe/Al{sub 2}O{sub 3} and BOF dust samples showed low activities on coal volatiles catalytic decomposition. 21 refs., 5 figs., 3 tabs.

Bio-coke as an alternative to petroleum coke and metallurgical coke; Bio-cokes als alternatief voor petroleumcokes en metallurgische cokes

Energy Technology Data Exchange (ETDEWEB)

Croezen, H.J.; Van Lieshout, M. [CE Delft, Delft (Netherlands); Sevenster, M.N. [Sevenster Environmental Consultancy, Australian Capital Territory ACT (Australia)

2012-11-15

In the framework of elaborating the Dutch Roadmap Chemistry 2030), CE Delft has conducted an exploratory study for the Association of the Dutch Chemical Industry (VNCI) on the options of replacing (petroleum) coke in the chemical sector by biocokes. Coke is used as a reducing agent and/or raw material in four companies in the Dutch chemical industry (Tronox, ESD-SIC, Thermphos, Aluchemie). Replacing coke at these four companies can potentially yield a direct CO2 reduction of expectedly several hundreds of kilotons per year. For a first exploration of the options of bio-coke, CE Delft first conducted a desk study to get information on the quality and production costs for bio-coke. Subsequently, CE Delft had contact with the four chemical companies and a made a number of company visits. Moreover, the technical, economic and organizational capabilities, constraints and requirements with regard to a possible (partial) switch to biocokes have been explored. Based on the information available so far it can be concluded that biocokes seems to be a technically and economically interesting innovation. For implementation to finally take place, it is necessary to gain better insight in the technical and economic potential [Dutch] In verband met de uitwerking van de Routekaart Chemie 2030 heeft CE Delft voor VNCI een verkenning uitgevoerd naar de mogelijkheden voor vervanging van (petroleum)cokes in de chemische sector door biocokes. Cokes wordt gebruikt als reductiemiddel en/of grondstof bij een viertal bedrijven in de Nederlandse chemie (Tronox, ESD-SIC, Thermphos, Aluchemie). Het vervangen van cokes bij deze vier bedrijven kan in potentie een directe CO2-reductie van naar verwachting enkele honderden kilotonnen/jaar opleveren. Voor een eerste verkenning van de mogelijkheden van bio-cokes heeft CE Delft eerst een bureaustudie uitgevoerd naar informatie over kwaliteit van en productiekosten voor bio-cokes. Vervolgens heeft CE Delft contact gehad met de vier chemische

China's coke industry: Recent policies, technology shift, and implication for energy and the environment

International Nuclear Information System (INIS)

Huo, Hong; Lei, Yu; Zhang, Qiang; Zhao, Lijian; He, Kebin

2012-01-01

China is the largest coke producer in the world, accounting for over 60% of the world coke production, which makes the coke industry in China a significant coal consumer and air pollutant emitter. Recently, China has taken a series of measures to improve energy efficiency and reduce emissions from the coke industry, including eliminating old and low energy-efficiency coking technologies, promoting advanced technologies, and strengthening energy and environmental requirements on coking processes. As a consequence, China's coke industry is experiencing an unprecedented technology shift, which was characterized by the elimination of old, inefficient, and polluting indigenous ovens and small machinery ones within 10 years. This study examines the policies and the prompt technology shift in China's coke industry, as well as the associated energy and environmental effects, and discusses the implications with respect to the development of the coke industry in China towards a more efficient and clean future. As China sets stricter requirements on energy efficiency and the ambient environment, a more significant change focusing on technologies of energy saving and emission reduction is urgently needed at present. Those mature technologies, including coke dry quenching, coke oven gas recycle, fine particle removal, etc., should be enforced in the near future. - Highlights: ► With 60% of world coke output, China's coke making has big energy/pollution issues. ► Actions were taken to improve energy and environmental performance of coke plants. ► China's coke industry is experiencing an unprecedented technology shift. ► Another shift, focusing on technologies of energy and emission saving, is needed. ► More measurement studies on coking emissions are needed given the importance.

The year-book of the Coke Oven Managers' Association 2007

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The 88th volume of the Year Book outlines activities of the Coke Oven Managers' Association throughout 2007 and reproduces transactions presented to the industry through its various sections. It includes lists of Council and committee members and representation on committees and past presidents, and a full list of members. Reports of Council 2005-6 and of the annual general meeting 2005 are included. The Presidential address by R.G.W. Sargent looks at the situation faced by coke oven managers through the decades with some predictions for the future. Carbonisation and briquetting works in the United Kingdom, Koppers carbon materials and chemical works in the UK and Europe, European coking plants, their addresses and managers are listed. Nine transactions are abstracted separately on the Coal Abstracts database.

Influence of thermal charge preparation on coke comminution under blast-furnace operating conditions

Energy Technology Data Exchange (ETDEWEB)

Shkoller, M.B.; Dinel' t, V.M.; Korchuganova, G.S.; Petrov, V.B.

1983-01-01

An investigation is described for the study of structural breakdown of coke by thermochemical action of alkali and alkaline-earth metal vapors under blast furnace operating conditions. Bench-scale test facilities are described in which a pair of coke samples are exposed to the metal vapors then subjected to gasification. Structural strength tests were performed before and after each experiment. Coke samples were obtained in either moist or thermally prepared condition. The value of thermal charge preparation (heat treatment of the coal at 150/sup 0/C in a fluidized bed) was established, since it shifts the pore size distribution to the smaller size, thereby retarding adsorption of the metal vapors. 16 references, 4 figures, 2 tables.

Part of the green plan : suppliers are helping the coal and oil sands industries to address environmental concerns

Energy Technology Data Exchange (ETDEWEB)

Sabourin, M.

2009-09-15

The Canadian coal and oil sands industries operate in one of the most stringent environmental regulatory frameworks found in the world. The purpose of the strict regulations is to ensure that Canadian energy resources are developed safely, responsibly and efficiently. Their primary objectives involve the protection of water supplies and aquatic life. This article discussed how suppliers are helping the coal and oil sands industries address environmental concerns. Several examples were provided. In terms of water protection and management, EBA Engineering Consultants has helped mining companies comply with strict environmental regulations and has assisted them in obtaining the necessary permits and establishing monitoring programs. In terms of containment, the Layfield Group's silt and sediment control products has helped prevent fine soil particles from running off into and clouding local water courses. In terms of land reclamation and remediation, IW Kuhn Environmental Ltd., has provided soil remediation services, including re-vegetation using hydroseeding which involves the sowing of seeds with a hosed jet of water. This article also discussed the many green technology products that have been developed and commercialized by EarthRenew for application in coal and oil sands projects. Their patented waste renew facilities can process and cook manures, biosolids or green wastes into organic fertilizers that could be used in land repair applications. 5 figs.

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2007-03-17

hydrodesulfurization. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Combustion and characterization of the latest fuel oil (the high temperature fraction of RCO from the latest modification) indicates that the fraction is heavier than a No. 6 fuel oil. Combustion efficiency on our research boiler is {approx}63% for the heavy RCO fraction, lower than the combustion performance for previous co-coking fuel oils and No. 6 fuel oil. Emission testing indicates that the coal derived material has more trace metals related to coal than petroleum, as seen in previous runs. An additional coal has been procured and is being processed for the next series of delayed co-coking runs. The co-coking of the runs with the new coal have begun, with the coke yield similar to previous runs, but the gas yield is lower and the liquid yield is higher. Characterization of the products continues. Work continues on characterization of liquids and solids from co-coking of hydrotreated decant oils; liquid yields include more saturated and hydro- aromatics, while the coke quality varies depending on the conditions used. Pitch material is being generated from the heavy fraction of co-coking.

Programmed heating of coke ovens for increased coke size

Energy Technology Data Exchange (ETDEWEB)

Jenkins, D.R.; Mahoney, M.R. [University of Newcastle, Callaghan, NSW (Australia)

2010-11-15

Large, uniform sized coke is desirable for blast furnace use. It has previously been shown that the coke oven flue temperature in the first few hours of coking is a key determinant of coke size. In this paper, the authors present a new programmed heating approach, which is called pulsed heating, aiming to increase coke mean size at a given average flue temperature. The approach takes into account the charging sequence in coke oven batteries and the authors demonstrate how existing operating practice can be modified in batteries with suitable heating systems to achieve the desired heating programme. A mathematical model of fissure formation provides a prediction of the increase in coke mean size using pulsed heating, compared with standard heating. Pilot scale experiments have also been performed to validate the modelling approach. The results of the modelling indicate that the mean coke size can be increased by several millimetres in some cases, although results from the pilot scale show that pulsed heating increases coke size, but by a smaller amount than that predicted by the model. The potential advantages and limitations of pulsed heating are discussed, as well as opportunities for further investigation of the approach.

Coal-92

International Nuclear Information System (INIS)

Hillring, B.; Sparre, C.

1992-11-01

Swedish consumption of coal and coke during 1991 and trends in technology, environment and market aspects of coal use are reported. Steam coal use in the heating sector was unchanged from 1991, 1.2 Mtons. Reduced consumption in smaller district heating units (due to conversion to biofuels and gas) was compensated by increased use for power generation in cogeneration plants. Coal consumption in industry fell 0.10 Mton to 0.84 Mton due to lower production in one industry branch. Import of steam coal was 1.1 Mton (down 0.5 Mton from 1990) since new rules for strategic reserves allowed a reduction of stocks. During the last five years stocks have been reduced by 2 Mtons. Import of metallurgical coal was 1.6 Mton, unchanged from 1990. The report also gives statistics for the coal using plants in Sweden, on coal R and D, and on emission laws for coal firing. (9 tabs., 2 figs.)

Oil from coal: just not worth it, say NCB

Energy Technology Data Exchange (ETDEWEB)

Grainger, L

1970-01-01

The creation of new markets by making oil fuels from coal in Britain is unresolved at this time. The dominant factor in the economics is the price ratio between coal and oil, which in Britain is 3 times less favorable than in the U.S. Current conversion results in a price more than double that of natural oil; however, the National Coal Board (NCB) continues to assess oil-from-coal processes. A sound research background in the new field of coal derivatives from solvent processing is being developed to produce materials of higher specific value than fuels. A continuous pilot plant is being built to prepare coke from filtered coal solution on the scale of a half-a-ton per week. Future prospects of the industry lie in areas where markets for coal will diminish, such as metallurgical coke. The fate of the coal industry will depend more and more on its largest market-electricity generation. In order to compete with nuclear power, the NCB is developing a new system of fluidized combustion.

Emission characteristics and size distribution of polycyclic aromatic hydrocarbons from coke production in China

Science.gov (United States)

Mu, Ling; Peng, Lin; Liu, Xiaofeng; He, Qiusheng; Bai, Huiling; Yan, Yulong; Li, Yinghui

2017-11-01

Coking is regarded as a major source of atmospheric polycyclic aromatic hydrocarbons (PAHs), but few researches have been conducted on the emission characteristics of PAHs from coke production. In this study, emissions of size-segregated particulate matter (PM) and particle-bound PAHs emitted from charging of coal (CC) and pushing of coke (PC) in four typical coke plants were determined. The emission factors on average, sums of CC and PC, were 4.65 mg/kg, 5.96 mg/kg, 19.18 μg/kg and 20.69 μg/kg of coal charged for PM2.1 (≤ 2.1 μm), PM, PAHs in PM2.1 and total-PAHs, respectively. PM and PAHs emission from plants using stamp charging were significantly more than those using top charging. The profile of PAHs in PM with size ≤ 1.4 μm (PM1.4) emitted from CC process were similar with that from PC, however, it revealed obviously different tendency for PAHs in PM with size > 1.4 μm, indicating the different formation mechanism for coarse particles emitted from CC and PC. Size distributions of PM and PAHs indicated that they were primarily connected with PM1.4, and the contributions of PM1.4 to PM and PAHs emitted from the plants using stamp charging were higher than those using top charging. Some improved technology in air-pollution control devices should be considered in coke production in future based on the considerable impacts of PM1.4 and PAHs on human health and ambient air quality.

Industrial use of coal and clean coal technology

Energy Technology Data Exchange (ETDEWEB)

Leibson, I; Plante, J J.M.

1990-06-01

This report builds upon two reports published in 1988, namely {ital The use of Coal in the Industrial, Commercial, Residential and Transportation Sectors} and {ital Innovative Clean Coal Technology Deployment}, and provides more specific recommendations pertaining to coal use in the US industrial sector. The first chapter addresses industrial boilers which are common to many industrial users. The subsequent nine chapters cover the following: coke, iron and steel industries; aluminium and other metals; glass, brick, ceramic, and gypsum industries; cement and lime industries; pulp and paper industry; food and kindred products; durable goods industry; textile industry; refining and chemical industry. In addition, appendices supporting the contents of the study are provided. Each chapter covers the following topics as applicable: energy overview of the industry sector being discussed; basic processes; foreign experience; impediments to coal use; incentives that could make coal a fuel of choice; current and projected use of clean coal technology; identification of coal technology needs; conclusions; recommendations.

Supercritical solvent extraction of oil sand bitumen

Science.gov (United States)

Imanbayev, Ye. I.; Ongarbayev, Ye. K.; Tileuberdi, Ye.; Mansurov, Z. A.; Golovko, A. K.; Rudyk, S.

2017-08-01

The supercritical solvent extraction of bitumen from oil sand studied with organic solvents. The experiments were performed in autoclave reactor at temperature above 255 °C and pressure 29 atm with stirring for 6 h. The reaction resulted in the formation of coke products with mineral part of oil sands. The remaining products separated into SARA fractions. The properties of the obtained products were studied. The supercritical solvent extraction significantly upgraded extracted natural bitumen.

The coke dilemma

Energy Technology Data Exchange (ETDEWEB)

Champagne, P E; Lewis, J A

1989-08-01

Coke-making capacity reductions and the current status of coke oven batteries in the USA are surveyed, as well as prior forecasts of the steel and coke markets. The future position is then analysed and it is concluded that the US coke supply situation should improve up to 1995, but that there could be major domestic coke production deficits in the period 1996-2000; critical decisions will soon have to be made about replacement of coking capacity.

Anomalous capillary flow of coal tar pitches

Energy Technology Data Exchange (ETDEWEB)

Saint Romain, J.L.; Lahaye, J.; Ehrburger, P.; Couderc, P.

1986-06-01

Capillary flow of liquid coal tar pitch into a coke bed was studied. Anomalies in the flow could not be attributed to a plugging effect for mesophase content lower than 20 wt%. The flow behaviour of small pitch droplets can be correlated with the change in physicochemical properties, as measured by the glass transition temperature, on penetration into the coke bed. 4 references.

Coal -98

International Nuclear Information System (INIS)

Sparre, C.

1998-01-01

The following report deals with the use of coal and coke during 1997. Some information about technic, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from SCB have also been used. The use of steam coal for heating purposes during 1997 was 730 000 tons and about 500 000 tons lower than in 1996. The extremely high figures of 1996 were due to twice the production of electricity because of lack of hydro power. The co-generation plants were the main users of coal. The minor plants have increased their use of forest fuels. Probably the use of steam coal will go down in the immediate years both in the heat generating and the co-generating plants. Some foreign analysts, however, estimate a doubled use of coal for energy use after 2020 because of the plans to phase out the nuclear power. During the top year 1987 coal was used in 18 hot water plants and 11 co-generation plants. 1997 these figures are 2 and 8. Taxes and environmental reasons explain this trend. The use of steam coal in the industry has been constant at the level 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1997 was 1.6 mill tons like the year before. 1.2 mill tons coke were produced. The coke consumption in the industry was 1.5 Mill tons. 0.3 mill tons of coke were imported. Several other plants have plans to replace the coal with forest fuels, waste fuels and NG. Even the biggest plant, Vaesteraas, has plans to build a block for bio fuels. Helsingborg has started to use wood pellets. The pellets replace most of the coal for the heat production in the co-generation plant. Norrkoeping Kraft AB has taken a fluid bed boiler for different fuels in operation, leading to more than half the coal consumption compared with previous years. They have also rebuilt one of their travelling grates for bio fuels. Stockholm

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre' Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2006-09-17

from the latest modification) indicates that the fraction is heavier than a No. 6 fuel oil. Combustion efficiency on our research boiler is {approx}63% for the heavy RCO fraction, lower than the combustion performance for previous co-coking fuel oils and No. 6 fuel oil. An additional coal has been procured and is being processed for the next series of delayed co-coking runs. Work continues on characterization of liquids and solids from co-coking of hydrotreated decant oils; liquid yields include more saturated and hydro- aromatics, while the coke quality varies depending on the conditions used. Pitch material is being generated from the heavy fraction of co-coking. Investigation of coal extraction as a method to produce RCO continues; the reactor modifications to filter the products hot and to do multi-stage extraction improve extraction yields from {approx}50 % to {approx}70%. Carbon characterization of co-cokes for use as various carbon artifacts continues.

Quarterly coal report, July--September 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-02-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks. Coke production consumption, distribution, imports, and exports data are also provided. This report presents detailed quarterly data for July through September 1997 and aggregated quarterly historical data for 1991 through the second quarter of 1997. Appendix A displays, from 1991 on, detailed quarterly historical coal imports data. 72 tabs.

US export coal in the 1990s - price, volume and quality

Energy Technology Data Exchange (ETDEWEB)

Bennett, J

1991-08-01

This report examines the following: current US coal exports; the domestic steam coal market and the domestic coking coal market; transport of export coal; reserves, production and productivity; and export markets for US coal. The report concluded that from the mid-1990s, buyers of the leading US coal export brands will face steadily rising prices as a result of fundamental shifts in the US domestic market affecting those regions supplying the bulk of the country's exports. The coals at the forefront of these price rises will be low-sulphur steam coal and high-volatile coking coal. Districts 8 and 7, the region that produces most of these types of coal, will be called upon to expand production by 50 m short tons per year by the end of the decade. However, there will be little scope for further productivity gains and because of this, and the need for significant capital investment, mining costs will rise. Inland freight rates will also rise as barge companies and railroads seek to cover investments. 53 figs., 66 tabs.

North American natural gas outlook : does gas remain a fuel option for oil sands?

International Nuclear Information System (INIS)

George, R.R.

2003-01-01

This paper presents a North America natural gas outlook from Purvin and Gertz, an international energy consulting firm that has 30 years experience in providing strategic, commercial and technical advice to the petroleum industry. In particular, this presentation focuses on natural gas market fundamentals and how they may impact on oil sands development. It includes charts and graphs depicting NYMEX natural gas outlooks to July, 2009 and examines how supply will react to major changes in Canada's supply portfolio. It was noted that oil sands development is a driver for natural gas demand in Alberta. The existing regional gas pipeline infrastructure was presented and the market impact on upgrader options was discussed. The author suggests that if gas prices are too high, there are other fuel options for steam and power generation. These include bitumen, asphalt, coke, coal and nuclear. However, these options have additional costs, uncertainties and environmental issues. A key factor for success would be to have a clear understanding of the benefits and risks between these fuel options. 1 tab., 9 figs

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2006-05-17

This report summarizes the accomplishments toward project goals during the first six months of the third year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. Characterization of the gasoline fuel indicates a dominance of single ring alkylcycloalkanes that have a low octane rating; however, blends containing these compounds do not have a negative effect upon gasoline when blended in refinery gasoline streams. Characterization of the diesel fuel indicates a dominance of 3-ring aromatics that have a low cetane value; however, these compounds do not have a negative effect upon diesel when blended in refinery diesel streams. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Combustion and characterization of fuel oil indicates that the fuel is somewhere in between a No. 4 and a No. 6 fuel oil. Emission testing indicates the fuel burns similarly to these two fuels, but trace metals for the coal-based material are different than petroleum-based fuel oils. Co-coking studies using cleaned coal are highly reproducible in the pilot-scale delayed coker. Evaluation of the coke by Alcoa, Inc. indicated that while the coke produced is of very good quality, the metals content of the carbon is still high in iron and silica. Coke is being evaluated for other possible uses

Ways of intensifying the conventional chamber carbonization of hard coal

Energy Technology Data Exchange (ETDEWEB)

Pelagalli, M.

1986-12-01

The intensification measures are intended to reduce both the investment cost and the operating cost via an increased performance factor. Automation had good results both in coal blending and in process monitoring and control. Coal blending, compression, and partial briquetting extend the range of coking coals.

Emission of Polychlorinated Dibenzo-p-Dioxins (PCDDs and Polychlorinated Dibenzofurans (PCDFs from Underfiring System of Coke Oven Battery

Directory of Open Access Journals (Sweden)

Rafał Bigda

2017-11-01

Full Text Available A coke oven battery is not considered as a significant source of PCDDs/PCDFs emissions; however, due to small amounts of chlorine in coal dioxins, dibenzofurans may be formed. The paper presents the attempts to determine the level of emission of PCDDs/PCDFs from the COB underfiring system and to confront the obtained results with the calculations based on the mass balance of chlorine in the coking process and reactions of both chlorophenols formation and PCDDs and PCDFs formation from mono- and polychlorophenols. There were PCDDs/PCDFs concentrations measured in flue gases from the underfiring system of two COBs at a Polish coking plant. The measurements included both an old and a new battery. The obtained concentrations of PCDDs/PCDFs were lower than reported in the literature (0.5-1.7 ng I-TEQ/tcoke, while the results for old COB were on average 3 times higher than for the new one. It was found that PCDD/F emission from COB underfiring system is insignificant and that PCDDs/PCDFs formation during coal coking should consider the mechanisms of their formation from mono- and polychlorophenols, as well as the influence of process parameters on the synthesis.

Buckets of money for coal

International Nuclear Information System (INIS)

Anon

2001-01-01

The revival of coal prices is providing record profits for Australian coal producers. As the world's largest coal exporter, any move in coal prices has significant ramifications for the Australian economy. The coal boom of the mid-1980s resulted in a massive increase in mine capacity and subsequently excess supply. This resulted in the decade between 1990 and 2000 seeing benchmark prices for coking coal in Japan plummeting to $US 39 a tonne (down from around the $US 52 mark) and a price of $US 28 for a tonne of steaming coal. Asia's financial problems, late in the decade coupled with a rapid fall in Asian steel making, also added to our coal export woes. As a result for most of the 1990s, Australia's coal sector delivered inadequate returns, was seen as over-capitalised and suffered from a profound investor indifference. But the sector is now seeing a definite turnaround in fortunes. Prices for thermal coal are on the rise and the benchmark coking coal prices to Asia have also jumped. Market analysts reported the price for contract deliveries of thermal coal in April this year were $US 34.50 ($AUD 69.35) up by $US 5.75 from the same time last year. The increased production is expected on the back of a continued rise in export demand, further improvement in prices, significant improvements in mine productivity, a weak Australian dollar and the probability of new projects and mine extensions going into operation. The improved returns have also flowed into rising valuations for listed coal miners. Over the last year, coal miners such as MIM and Gympie Gold, have delighted in share price gains of 12 per cent and 55 per cent respectively. These sort of performances are being repeated across the Australian industry

Quarterly coal report, July--September 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. This report presents detailed quarterly data for July through September 1998 and aggregated quarterly historical data for 1992 through the second quarter of 1998. 58 tabs.

Biological CO2 conversion to acetate in subsurface coal-sand formation using a high-pressure reactor system

Directory of Open Access Journals (Sweden)

Yoko eOhtomo

2013-12-01

Full Text Available Geological CO2 sequestration in unmineable subsurface oil/gas fields and coal formations has been proposed as a means of reducing anthropogenic greenhouse gasses in the atmosphere. However, the feasibility of injecting CO2 into subsurface depends upon a variety of geological and economic conditions, and the ecological consequences are largely unpredictable. In this study, we developed a new flow-through-type reactor system to examine potential geophysical, geochemical and microbiological impacts associated with CO2 injection by simulating in situ pressure (0–100 MPa and temperature (0–70°C conditions. Using the reactor system, anaerobic artificial fluid and CO2 (flow rate: 0.002 and 0.00001 mL/min, respectively were continuously supplemented into a column comprised of bituminous coal and sand under a pore pressure of 40 MPa (confined pressure: 41 MPa at 40°C for 56 days. 16S rRNA gene analysis of the bacterial components showed distinct spatial separation of the predominant taxa in the coal and sand over the course of the experiment. Cultivation experiments using sub-sampled fluids revealed that some microbes survived, or were metabolically active, under CO2-rich conditions. However, no methanogens were activated during the experiment, even though hydrogenotrophic and methylotrophic methanogens were obtained from conventional batch-type cultivation at 20°C. During the reactor experiment, the acetate and methanol concentration in the fluids increased while the δ13Cacetate, H2 and CO2 concentrations decreased, indicating the occurrence of homo-acetogenesis. 16S rRNA genes of homo-acetogenic spore-forming bacteria related to the genus Sporomusa were consistently detected from the sandstone after the reactor experiment. Our results suggest that the injection of CO2 into a natural coal-sand formation preferentially stimulates homo-acetogenesis rather than methanogenesis, and that this process is accompanied by biogenic CO2 conversion to

Quarterly coal report, April--June, 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-11-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. This report presents detailed quarterly data for April through June 1998 and aggregated quarterly historical data for 1992 through the first quarter of 1998. Appendix A displays, from 1992 on, detailed quarterly historical coal imports data. 58 tabs.

Quarterly coal report, October--December 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. This report presents detailed quarterly data for October through December 1998 and aggregated quarterly historical data for 1992 through the third quarter of 1998. Appendix A displays, from 1992 on, detailed quarterly historical coal imports data. 58 tabs.

Developing densification technology to facilitate briquetting of coal fines

Energy Technology Data Exchange (ETDEWEB)

Shi, R. [Ministry of Metallurgy (China). Anshan Thermal Energy Research Institute

1997-01-01

This paper introduces the densification technology in coal processing and the research of increasing the caking power of coal and its application. By exploiting the inherent caking property of coal, it is hoped to advance the briquetting technology so that coal fines is converted into high quality coke or briquette. This will produce very good social, economical and environmental benefit. 3 figs., 5 tabs.

Preparation and evaluation of coal extracts as precursors for carbon and graphite products

Energy Technology Data Exchange (ETDEWEB)

Zondlo, J.W.; Stiller, A.W.; Stansberry, P.G. [West Virginia Univ., Morgantown, WV (United States)] [and others

1996-08-01

A coal extraction process coupled with coal hydrotreatment has been shown capable of producing suitable precursors for a variety of commercially important carbon and graphite products. The N-methylpyrolidone (NMP) extracts of hydrotreated coals have been analytically and chemically characterized and shown to have properties acceptable for use as binder and impregnation pitch. Mesophase formation studies have demonstrated their capability for producing both needle and anode grade coke as well as precursors for mesophase pitch fibers. A graphite artifact has been produced using a coal extract as a binder and coke derived from the extract as a filler. Further evaluation of the extract materials is being carried out by industrial members of the Carbon Products Consortium.

Self-cementitious properties of fly ashes from CFBC boilers co-firing coal and high-sulphur petroleum coke

International Nuclear Information System (INIS)

Sheng Guanghong; Li Qin; Zhai Jianping; Li Feihu

2007-01-01

Self-cementitious properties of fly ash from circulating fluidized bed combustion boiler co-firing coal and high-sulphur petroleum coke (CPFA) were investigated. CPFA was self-cementitious which was affected by its fineness and chemical compositions, especially the contents of SO 3 and free lime (f-CaO). Higher contents of SO 3 and f-CaO were beneficial to self-cementitious strength; the self-cementitious strength increases with a decrease of its 45 μm sieve residue. The expansive ratio of CPFA hardened paste was high because of generation of ettringite (AFt), which was influenced by its water to binder ratio (W/A), curing style and grinding of the ash. The paste cured in water had the highest expansive ratio, and grinding of CPFA was beneficial to its volume stability. The hydration products of CPFA detected by X-ray diffraction (XRD) and scanning electron microscopy (SEM) were portlandite, gypsum, AFt and hydrated calcium silicate (C-S-H)

Design and construction of coke battery 1A at Radlin coke plant, Poland

Energy Technology Data Exchange (ETDEWEB)

A.M. Kravchenko; D.P. Yarmoshik; V.B. Kamenyuka; G.E. Kos' kova; N.I. Shkol' naya; V.V. Derevich; A.S. Grankin [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

2009-07-15

In the design and construction of coke battery 1A at Radlin coke plant (Poland), coking of rammed coke with a stationary system was employed for the first time. The coke batteries are grouped in blocks. Safety railings are provided on the coke and machine sides of the maintenance areas.

Forty years of the Weglopochodne Enterprise for Sale of Coal-Derived Products

Energy Technology Data Exchange (ETDEWEB)

Pinkowski, Z.

1986-02-01

Organizational structure of trade in coal-derived products in Poland from 1945 to 1985 is discussed. Fluctuations of organizational structures reflecting phases of centralization and decentralization of the national economy are analyzed. Coordinating role of the Weglopochodne Enterprise in the coking and chemical industries is stressed. Types of products produced by coking plants in Poland, trade and exports are discussed. Effects of organizational structures on development of coking plants are also discussed (increasing wear of coking plants, insufficient investment etc.). 3 references.

Industrial coal survey

Energy Technology Data Exchange (ETDEWEB)

1992-05-25

UK industrial coal sales were down 400,000t to 7.1mt in 1991. This was largely due to fall in cement purchases as the construction industry was badly hit in the recession. Increased competition from petroleum coke also had an effect. A brief roundup is presented of sales to the UK's major coal buyers: Alcan, ICI, Blue Circle, Castle Cement, Rugby Cement, British Steel, UK Paper, Courtaulds, Unilever, AHS Emstar, Tate Lyle, and British Sugar. 1 tab.

The behaviour of Pacific metallurgical coal markets: the impact of Japan's acquisition strategy on market price

Energy Technology Data Exchange (ETDEWEB)

Koerner, R J [Queensland University, St. Lucia, Qld. (Australia). Graduate School of Management, Faculty of Commerce and Economics

1993-03-01

This paper examines whether some elements of Japan's resource acquisition strategies might have caused price and other distortions of market behaviour in the Pacific metallurgical coal trade. The industry chosen for investigation is that of steel manufacture, and the traded resources commodity examined is coking coal, which is the primary energy input for blast furnace iron making. Regression modelling studies to determine historic acquisition value and quality relationships for US, Australian and Canadian coals sold into the Japanese coking coal market are described. Departures from normal demand response behaviour to price competitiveness are also investigated. 3 figs., 3 tabs.

Distillation of tar and tar fractions in the presence of surface-active coke

Energy Technology Data Exchange (ETDEWEB)

Jaeppelt, A; Klaus, J

1943-01-01

The tar obtained by low-temperature carbonization of Upper Silesian gas coke and fractions from this tar were distilled in the presence of different grades of coke dust with varying surface activity; the coke had been activated by steam in the course of its production by low-temperature carbonization. The surface activity of the coke dusts was measured by determining the heat of wetting with C/sub 6/H/sub 6/. Tar and coke dust, both anhydrous, were mixed in a kneading machine in such proportions that the capillaries of the dust were saturated and enough ''externally'' bound tar was present to permit briquetting. The briquets were distilled without cracking and with steam as heating medium. The yield and quality of the distillate depended on the magnitude of the internal surface of the coke dust used; a mixture of a very active coke from brown coal and tar yielded a distillate with Conradson carbon residue of 1.34 percent, asphalt content 6.1 percent and eta/sub 20/ 5.4/sup 0/ E. as compared with C residue of 10.95 percent, asphalt content 33.5 percent and eta/sub 20/ 123.6/sup 0/ E. of the distillate obtained in the absence of surface-active coke. Even higher-boiling fractions can be improved by this treatment, although it is preferable to use oils with an initial boiling point below 300/sup 0/. The ratio of oil to adsorbent is not critical, but better results were obtained with higher percentages of added coke dust. The process in its present form is not suited for the conversion of crude creosote to useful phenols.

Prediction of vertical expansion pressure stresses in coke oven heating walls

Energy Technology Data Exchange (ETDEWEB)

Duerselen, H; Janicka, J

1987-08-01

The paper describes an accurate method developed by Krupp Koppers for calculating stresses in the central areas of coke oven heating walls. The results of this calculation model have provided the following conclusions for the design of coke ovens: 1) a rising pre-stressing of the heating walls caused by the weight of the top deck of the coke oven leads - compared with the stress limits of W. Ahlers - to lower permissible expansion pressures. 2) A given heating wall width has its corresponding maximum feasible oven height. Heating wall width and top deck weight are not interchangeable parameters. 3) The dependence of the permissible expansion pressure on the stretcher brick thickness should not be overlooked. Stretcher brick thicknesses of under 90 mm are not recomended for tall ovens and heavily swelling coal. 4) The capacity of mortar to absorb tensile stresses is ultimately an undesirable property, because the stresses at the points where the mortar is not holding are higher than in a straightforward stretch of brickwork.

PROBLEMS WITH DETERMINATION OF FUGITIVE EMISSION OF POLYCYCLIC AROMATIC HYDROCARBONS FROM COKE OVEN BATTERY

Directory of Open Access Journals (Sweden)

Rafał Bigda

2017-03-01

Full Text Available Coke oven battery is complex and multifaceted facility in terms of air pollutant emissions. As far as stack or quenching tower does not cause major difficulties of emission measurement, the fugitive emission measurement from sources such as battery top elements (charging holes, ascension pipes or oven doors is still complicated and not fully solved problem. This article presents the discussion concerning main problems and errors likely to be made in particular stages of procedure of fugitive emissions characterization from coke oven battery (selection of sampling points, sampling itself, measurement of air velocity over battery top and laboratory analyses. In addition, results of concentrations measurements of selected substances characteristic for the coking process (naphthalene, anthracene, 4 PAHs and TSP originating from fugitive sources of coke oven battery and subjected to reporting under the E-PRTR are presented. The measurements were carried out on coke oven battery top in points selected on the basis of the preceding detailed air convection velocity measurements over battery top. Results of the velocity measurements were compared with results of numerical modelling using CFD software. The presented material is an attempt to cross-sectional presentation of issues related to the quantitative evaluation of fugitive emission from coke oven battery, discussed on the example of PAHs emission as a group of substances characteristic for coking of coal.

Integrated oil sands tailings pond water treatment

Energy Technology Data Exchange (ETDEWEB)

Guo, Z. [Saskatchewan Research Council, Saskatoon, SK (Canada)

2010-07-01

This PowerPoint presentation discussed research currently being conducted to treat oil sands tailings pond water (TPW). The treatment of TPW is challenged by the high level of naphthenic acids (NAs), the slow settling rate of fine particulate materials, and the complex chemistry of the water. The treatment process consisted of bioflocculation, sludge blanket assisted clarification, ozonation, and oil sands coke assisted hybrid biodegradation. The aggregation and adsorption process bound small particles and cells together while also ensuring the passive uptake of pollutants using microbial masses. The mixed liquor then passed through a sludge blanket to ensure enhanced particle capture. An ozonation process was used to increase the biodegradability of the TPW as well as to increase the biodegradability of the residual NAs after ozonation. The process used a hybrid bioreactor that consisted of both suspended and fixed microbial communities. The coke served as a biofilm carrier for the waste. Further studies are being conducted to investigate the efficiency and capability of the process. tabs., figs.

A comparative economic assessment of hydrogen production from coke oven gas, water electrolysis and steam reforming of natural gas

International Nuclear Information System (INIS)

Nguyen, Y.V.; Ngo, Y.A.; Tinkler, M.J.; Cowan, N.

2003-01-01

This paper presents the comparative economics of producing hydrogen for the hydrogen economy by recovering it from waste gases from the steel industry, by water electrolysis and by conventional steam reforming of natural gas. Steel makers produce coke for their blast furnace operation by baking coal at high temperature in a reduced environment in their coke ovens. These ovens produce a coke oven gas from the volatiles in the coal. The gas, containing up to 60% hydrogen, is commonly used for its heating value with some of it being flared. The feasibility of recovering this hydrogen from the gas will be presented. A comparison of this opportunity with that of hydrogen from water electrolysis using low cost off-peak electricity from nuclear energy will be made. The impact of higher daily average electricity rate in Ontario will be discussed. The benefits of these opportunities compared with those from conventional steam reforming of natural gas will be highlighted. (author)

Method of determining coking temperature of coke. [Experimental method of determining final coking temperature using a small sample and calibration graph

Energy Technology Data Exchange (ETDEWEB)

Mel' nichuk, A.Yu.; Bondarenko, A.K.; Fialkov, B.S.; Khegay, L.U.; Khvan, L.A.; Muzyzhuk, V.D.; Zakharov, A.G.; Zelenskiy, V.P.

1985-01-01

The coking temperature of coke should be determined from the magnitude of the ionization current of the medium during heating (3/sup 0//min) of a coke sample (2 g, fraction < 0.2 mm) in an oxidation medium with air supply (1 1/min). The coking temperature is determined from the maximum magnitude of current using a graduated graph constructed during analysis of coke samples obtained with different final coking temperatures. The discrepancy between the established coking temperature and that defined from the proposed method is 8-19/sup 0/, and that defined from electrical resistance of coke is 26-43/sup 0/. In addition to high accuracy, this method reduces the time outlays for making the analysis.

Advances in coal chemistry, 1950--1970. [21 refs

Energy Technology Data Exchange (ETDEWEB)

Brooks, J D

1971-12-01

During the 20 years under review, considerable advances were made at centers of coal research throughout the world in the determination of the chemical structure and reactions of coals. Important contributions came from the CSIRO group in Sydney. Activity was greatest during the first decade of the period under review and declined progressively during the second, as evidence of the extreme complexity of coal structures made it clear that further chemical research would be less rewarding. Some overseas investigations were related mainly to chemical processes for the conversion of coals to liquid and gaseous fuels, and to possible direct chemical utilization; but in Australia, because of the relatively small size of the potential market and the widely dispersed centers of population, such studies were not relevant to the current situation. Much of the Australian research in this field was related to carbonization processes and to the chemical and physical processes involved in the thermal treatment of coals. The high-light was perhaps the investigation, begun in 1960, which showed how coals, pitch, and bitumen resolidify during heating to form coke. Determinations were also made of the chemical composition of tars and pitches produced both industrially and in the laboratory and efforts were made to develop local outlets for these by-products of gas-making and of steelworks coke ovens. The pattern of Australian fuel consumption changed considerably during the 20-year period, and in particuar there was considerable development in the use of petroleum by-products for gas-making. Research on the manufacture of metallurgical coke was established within the steel industry, and in response to these factors basic work by CSIRO in bituminous coal chemistry had virtually ceased by the end of 1966.

Quality of some Nigerian coals as a blending stock in metallurgical ...

African Journals Online (AJOL)

Lafia- Obi/foreign coals blends possess lower ash and better rheological properties compared to Chikila/foreign coal composites which have high ash and poor rheological properties. These together suggest that amongst the two Nigerian coals, Lafia-Obi is superior for blending with the foreign ones in metallurgical coke ...

A study of the performance of a reclamation soil cover placed over an oilsands coke deposit

Energy Technology Data Exchange (ETDEWEB)

Fenske, D.S.; Barbour, S.L. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Civil Engineering; Qualizza, C. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

2006-07-01

Coke is a solid, carbonaceous residue that forms during the cracking of high-boiling point distillates and is one of the by-products of petroleum extraction from oilsands. Coke is known as a possible future energy source and therefore, must be stored within the reclaimed landscape in a form that allows it to be recovered. In addition, it also could be used as a low-density capping material over soft tailings. This paper presented the results of a study that examined the effects of coke in the environment. The study involved construction of two small instrumented watersheds at Syncrude Canada's Mildred Lake Settling Basin. Preliminary field data, highlighting the moisture dynamics within the covers and the underlying coke were discussed. Sand tailings underlie the hydraulically placed coke deposit. Overlying the coke were two different reclamation soil covers constructed of a peat/mineral mix over glacial or glacial lacustrine soils. Placing the finer textured soil cover over coarser grained coke produced a textural or capillary break which enhanced moisture storage for plant use while minimizing deep percolation of infiltrating water. The site has been instrumented with a meteorological station; automated soil stations to monitor suction, water content and temperature through the cover profile; lysimeters to collect net percolation; access tubes for water content monitoring; gas sampling points at depth in the coke; and standpipe piezometers to monitor water chemistry and total head in the coke at depth. 10 refs., 2 tabs., 16 figs.

Dale Coke: Coke Farm

OpenAIRE

Farmer, Ellen

2010-01-01

Dale Coke grew up on an apricot orchard in California’s Santa Clara Valley. In 1976 he bought ten acres of farmland near Watsonville in Santa Cruz County but continued to work repairing fuel injection systems rather than farming at his new home. In 1981, a struggle with cancer inspired him to rethink his life and become an organic farmer. His neighbor, who had grown strawberries using pesticides and chemical fertilizers, asserted that strawberries could not be grown organically. Coke set out ...

Differences in the irradiation effects of IG-110 and IG-430 nuclear graphites : effects of coke difference

International Nuclear Information System (INIS)

Chi, Se Hwan; Kim, Gen Chan; Kim, Eung Seon; Hong, Jin Ki; Chang, Jong Hwa

2005-01-01

In the high temperature gas cooled reactors (HTGRs), graphite acts as a moderator and reflector as well as a major structural component that may provide channels for the fuel and coolant gas, channels for control and shut down, and thermal and neutron shielding. During a reactor operation, many of the physical, chemical and mechanical properties of these graphite components are significantly modified as a function of the temperature, environment, and an irradiation. On the other hand, currently, all the nuclear graphites are being manufactured from two types of cokes, i.e., petroleum and coal-tar pitch coke, and it has been understood that the type of coke plays the most critical role determining the properties of a specific graphite grade. To investigate the effects of coke types on the irradiation response of a graphite, two graphites of different cokes were irradiated by 3 MeV C+ ions and the differences in the response of ion-irradiation were investigated

A novel approach to mitigating sulphur dioxide emissions and producing a mercury sorbent material using oil-sands fluid coke

International Nuclear Information System (INIS)

Morris, E.; Jia, C.Q.; Tong, S.

2008-01-01

Pyrometallurgical smelting operations are a major source of sulphur dioxide (SO 2 ) which is a precursor to acid rain and increased levels of UV-B penetration in boreal lakes. Mercury is also released in copper smelter off-gas, which can bioaccumulate and cause neurological disorders and death in humans. Fluid coke is produced in massive quantities as a by-product of bitumen upgrading at Syncrude Canada's facility in Fort McMurray, Alberta. Oilsands fluid coke can be used to reduce SO 2 and produce elemental sulphur as a co-product. This process was dubbed SOactive. The reaction physically activates the fluid coke to produce a sulphur-impregnated activated carbon (SIAC) which is known as ECOcarbon. Some studies have indicated that SIAC is well suited for the removal of vapour phase mercury, mainly due to the formation of stable mercuric sulphide species. This paper discussed the findings made to date in relation to the SOactive process and the characterization of ECOcarbons. The paper discussed the use of fluid coke for reducing SO 2 emissions while producing elemental sulphur as well as coke-SO 2 -oxygen (O 2 ) and coke-SO 2 -water (H 2 O) systems. The paper also examined the production of SIAC products for use in capturing vapour phase mercury. The paper presented the materials and methodology, including an illustration of the apparatus used in reduction of SO 2 and activation of fluid coke. It was concluded that more work is still needed to analyse the effect of O 2 and SO 2 reduction and SIAC properties under smelter flue gas conditions. 10 refs., 1 tab., 8 figs

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline Clifford; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2008-03-31

designed for natural gas/fuel oil, and determining the boiler performance when firing the five fuels. Two different co-processed fuel oils were tested: one that had been partially hydrotreated, and the other a product of fractionation before hydrotreating. Task 5 focused on examining refining methods that would utilize coal and produce thermally stable jet fuel, included delayed coking and solvent extraction. Delayed coking was done on blends of decant oil and coal, with the goal to produce a premium carbon product and liquid fuels. Coking was done on bench scale and large laboratory scale cokers. Two coals were examined for co-coking, using Pittsburgh seam coal and Marfork coal product. Reactions in the large, laboratory scaled coker were reproducible in yields of products and in quality of products. While the co-coke produced from both coals was of sponge coke quality, minerals left in the coke made it unacceptable for use as anode or graphite grade filler.

Co-pyrolysis of coal with hydrogen-rich gases. 1. Coal pyrolysis under coke-oven gas and synthesis gas

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Li, B.; Zhang, B. [Chinese Academy of Sciences, Taiyuan (China). State Key Lab. of Coal Conversion

1998-06-01

To improve the economics of the hydropyrolysis process, it has been suggested that cheaper hydrogen-rich gases (such as coke oven gas, synthesis gas) could be used instead of pure hydrogen. Pyrolysis of Chinese Xianfeng lignite was carried out with coke oven gas (COG) and synthesis gas (SG) as reactive gases at 0.1-5 MPa and at a final temperature up to 650{degree}C with a heating rate of 5-25{degree}C min{sup -1} in a 10 g fixed-bed reactor. The results indicate that it is possible to use COG and SG instead of pure hydrogen in hydropyrolysis, but that the experimental conditions must be adjusted to optimize the yields of the valuable chemicals. 14 refs., 3 figs., 6 tabs.

A process for briquetting coal with the production of briquets with high resistance to crushing

Energy Technology Data Exchange (ETDEWEB)

Ono, M; Ito, S; Nakagava, K

1983-02-08

Finely ground coal is mixed with a binder with a softening point of greater than or equal to 30 degrees and with heavy coal tar products, the mixture is molded with the formation of briquets in a two roller press. The mixing is conducted in heated steam or waste gases from a horizontal, helical mixer. The coal is subsequently irrigated by the melted binder and heavy coal tar products. The heavy coal tar products are a bottom residue formed by condensation of volatile products in a gas stream from coking which contains particles of coal and coke. Briquets with a point compression strength of 50 plus or minus 4 kilograms per sq. cur. and a bulk tensity of 1.17 grams per cubic centimeter are produced from a mixture which contains 6 percent binder, 80 percent coal and 20 percent heavy coal tar products.

The Indonesian coal industry

International Nuclear Information System (INIS)

Cook, A.; Daulay, B.

2000-01-01

In this comprehensive article the authors describe the origins and progress of the Indonesian coal industry and the role it plays, and will play, in the domestic energy scene and world coal trade. In the '80s, the Indonesian coal industry laid the basis for major expansion such that coal production rose from under a million tonnes in 1983 to 10.6 million tonnes in 1990, 50.9 million tonnes by 1996 and 61.2 million tonnes in 1992. At the same time, exports have increased from 0.4 million tonnes to 44.8 million tonnes. Current export levels are higher than originally expected, due in part to a slow down in the construction of electric power stations and a partial switch to natural gas. This has slowed the rate at which domestic coal demand has built up. The majority of coals currently exported are low rank steam coals, but some of the higher rank and very low ash coals are used for blast furnace injection, and a very small proportion may even be used within coking blends, even though they have poor coking properties. The Indonesian coal industry has developed very rapidly over the last six years to become a significant exporter, especially within the ASEAN context. The resources base appears to be large enough to support further increases in production above those already planned. It is probable that resources and reserves can be increased above the current levels. It is likely that some reserves of high value coals can be found, but it is also probable that the majority of additions to reserves will be lower in rank (and therefore quality) compared with the average of coals currently being mined. Reserves of qualities suitable for export will support that industry for a considerable period of time. However, in the longer term, the emphasis of production will increasingly swing to the domestic market

Activities of the Institute of Chemical Processing of Coal at Zabrze

Energy Technology Data Exchange (ETDEWEB)

Dreszer, K.

1995-12-31

The Institute of Chemical Processing of Coal at Zabrze was established in 1955. The works on carbochemical technologies have been, therefore, carried out at the Institute for 40 years. The targets of the Institute`s activities are research, scientific and developing works regarding a sensible utilization of fuels via their processing into more refined forms, safe environment, highly efficient use of energy carriers and technological products of special quality. The Institute of Chemical Processing of Coal has been dealing with the following: optimized use of home hard coals; improvement of classic coal coking technologies, processing and utilization of volatile coking products; production technologies of low emission rate fuels for communal management; analyses of coal processing technologies; new technologies aimed at increasing the efficiency of coal utilization for energy-generating purposes, especially in industry and studies on the ecological aspects of these processes; production technologies of sorbents and carbon activating agents and technologies of the utilization; rationalization of water and wastes management in the metallurgical and chemical industries in connection with removal of pollution especially dangerous to the environment from wastes; utilization technologies of refined materials (electrode cokes, binders, impregnating agents) for making electrodes, refractories and new generation construction carbon materials; production technologies of high quality bituminous and bituminous and resin coating, anti-corrosive and insulation materials; environmentally friendly utilization technologies for power station, mine and other wastes, and dedusting processes in industrial gas streams.

Hydrogen production by co-gasification of coal and renewables

Energy Technology Data Exchange (ETDEWEB)

Fermoso, J.; Arias, B.; Rubiera, F.; Arenillas, A.; Pis, J.J. [Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo, (Spain)

2006-07-01

In this work, co-gasification of two coals with samples of pet-coke, sewage sludge and biomass was conducted at atmospheric pressure in a fixed bed reactor under steam/oxygen atmosphere, in order to evaluate possible synergistic effects during co-gasification. Experiments carried out at non-isothermal conditions for blends of a low volatile bituminous coal and dried sewage sludge, indicated the absence of interactive effects between the blends. The concentration of H{sub 2} and CO could be predicted from the concentrations of the individual components in the blends and their respective mass fractions. The results obtained under isothermal (1000 C) conditions for blends of a high ash coal with pet-coke, and blends with biomass (chestnut) produced less gas yield than the theoretically calculated. However, for the mixtures of coal and biomass the quality of the syngas, expressed by the amount of the produced H{sub 2}+CO and by the H{sub 2}/CO ratio, was not altered. (authors)

Hydrogen production by co-gasification of coal and renewables

International Nuclear Information System (INIS)

Fermoso, J.; Arias, B.; Rubiera, F.; Arenillas, A.; Pis, J.J.

2006-01-01

In this work, co-gasification of two coals with samples of pet-coke, sewage sludge and biomass was conducted at atmospheric pressure in a fixed bed reactor under steam/oxygen atmosphere, in order to evaluate possible synergistic effects during co-gasification. Experiments carried out at non-isothermal conditions for blends of a low volatile bituminous coal and dried sewage sludge, indicated the absence of interactive effects between the blends. The concentration of H 2 and CO could be predicted from the concentrations of the individual components in the blends and their respective mass fractions. The results obtained under isothermal (1000 C) conditions for blends of a high ash coal with pet-coke, and blends with biomass (chestnut) produced less gas yield than the theoretically calculated. However, for the mixtures of coal and biomass the quality of the syngas, expressed by the amount of the produced H 2 +CO and by the H 2 /CO ratio, was not altered. (authors)

Importance of the textural characteristics of inert additives in the reduction of coal thermoplastic properties

Energy Technology Data Exchange (ETDEWEB)

A.M. Fernandez; C. Barriocanal; M.A. Diez; R. Alvarez [Instituto Nacional del Carbon, Oviedo (Spain)

2010-11-15

Seven carbonaceous materials of different origin were chosen in order to study the influence of their porous structure on the modification of the thermoplastic properties of a bituminous coal. The materials included were: two non-coking coals, a petroleum coke, coke fines, two residues from tyre recycling and a bituminous residue. The materials were heat-treated to 900{sup o}C to prevent any chemical interaction between the volatiles evolved during co-carbonization. The thermoplastic properties of blends that contained 10 wt.% of additive were measured by means of the Gieseler test. Microporosity was measured by CO{sub 2} adsorption at 273 K, whereas meso and macroporosity were determined by means of mercury porosimetry. The results of the porous structure assessment are discussed in relation to the modification of coal plasticity. 32 refs., 5 figs., 5 tabs.

Quarterly coal report, January--March 1998

Energy Technology Data Exchange (ETDEWEB)

Young, P.

1998-08-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. This report presents detailed quarterly data for January through March 1998 and aggregated quarterly historical data for 1992 through the fourth quarter of 1997. Appendix A displays, from 1992 on, detailed quarterly historical coal imports data. To provide a complete picture of coal supply and demand in the United States, historical information has been integrated in this report. 58 tabs.

Quarterly coal report, October--December 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. This report presents detailed quarterly data for October through December 1996 and aggregated quarterly historical data for 1990 through the third quarter of 1996. Appendix A displays, from 1988 on, detailed quarterly historical coal imports data. To provide a complete picture of coal supply and demand in the US, historical information has been integrated in this report. 8 figs., 72 tabs.

CFD modelling and analysis of pulverized coal injection in blast furnace: an overview

Energy Technology Data Exchange (ETDEWEB)

Shen, Yansong; Yu, Aibing [Laboratory for Simulation and Modelling of Particulate Systems, School of Materials Science and Engineering, The University of New South Wales (UNSW), Sydney, NSW 2052 (Australia); Zulli, Paul [BlueScope Steel Research (BSR), P.O. Box 202, Port Kembla, NSW 2505 (Australia)

2011-05-15

In order to understand the complicated phenomena of pulverized coal injection (PCI) process in blast furnace (BF), several mathematical models have been developed by the UNSW and BSR cooperation. These models are featuring from coal combustion in a pilot-scale test rig, to coal combustion in a real BF, and then to coal/coke combustion in a real BF, respectively. This paper reviews these PCI models in aspects of model developments and model applicability. The model development is firstly discussed in terms of model formulation, their new features and geometry/regions considered. The model applicability is then discussed in terms of main findings followed by the model evaluation on their advantages and limitations. It is indicated that the three PCI models are all able to describe PCI operation qualitatively. The model of coal/coke combustion in a real BF is more reliable for simulating in-furnace phenomena of PCI operation qualitatively and quantitatively. Such model gives a more reliable burnout prediction over the raceway surface, which could better represent the amount of unburnt char entering the coke bed. These models are useful for understanding the flow-thermo-chemical behaviours and then optimising the PCI operation in practice. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Washability of Australian coals

Energy Technology Data Exchange (ETDEWEB)

Whitmore, R L

1979-06-01

Australian coals tend to be young in geological age and high in ash by world standards; preparation of the coal before marketing is almost universal. On the basis of float and sink data from 39 locations in the eastern Australian coalfields, the coals are place in four categories representing increasing difficulty in their washability characteristics. These seem to be related neither to the geological age nor the geographical position of the deposit and Hunter Valley coals, for example, span all categories. The influence of crushing on the washability of Australian coals is briefly considered and from limited data it is concluded to be appreciably smaller than for British or North American coals. A strategy for the float and sink analysis of Australian coals is proposed and the influence of washability characteristics on current trends in the selection of separating processes for coking and steaming products is discussed.

Effect of moisture on the accuracy of coke-ash determination by X-ray backscattering

International Nuclear Information System (INIS)

Pandey, H.D.; Prasad, M.S.

1984-01-01

Effect of moisture on the rapid non-destructive estimation of ash content in coal specimens using the X-ray backscattering technique has been studied extensively by various workers. In the present work, an attempt has been made to estimate its influence when the technique is extended to coke-ash determinations. From the study of the variation of backscattered intensity with change in the moisture content of a coke specimen, it is observed that the ash content varies significantly at moisture levels higher than 5%. The variation, however, remains within allowable limits if the moisture level is kept below 5%. This observation is confirmed by the actual measurement of ash percentages in thirteen coke specimens containing three different states of moisture levels viz. (i) in the dry state, (ii) with 5% moisture and (iii) with 10% moisture. (author)

Quarterly coal report, July--September 1993

Energy Technology Data Exchange (ETDEWEB)

1994-02-18

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. The data presented in the QCR are collected and published by the Energy Information Administration (EIA) to fulfill data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275), as amended.

Hot testing of coke

Energy Technology Data Exchange (ETDEWEB)

Balon, I D

1976-07-01

Earlier investigations failed to take full account of the factors affecting coke behavior within the blast furnace. An apparatus was accordingly developed for testing coke, based on a cyclone furnace where the sample could be held in a flow of hot oxidizing gases, simulating conditions in the blast furnace hearth. The results are said to be suitable for comprehensive assessment of the coke, including abrasive strength and its rate of gasification in a flow of carbon dioxide. Coke of size 6-10 mm tested at 1,100/sup 0/C in an atmosphere of oxidizing gases close to those obtaining in the blast furnace hearth, indicated that destruction and total gasification of the coke occurs after 5 minutes for a weak coke and 8 minutes for strong coke, depending on the physico-chemical and physico-mechanical properties of the particular coke. When samples were treated for a fixed period (3 minutes), the amount of coke remaining, and the percentage over 6 mm varied between 22 and 40 and between 4 and 7 percent respectively.

The new coke oven battery heating control system at Rautaruukki Steel

Energy Technology Data Exchange (ETDEWEB)

Palmu, P.; Swanljung, J. [Rautaruukki Steel, Raahe (Finland)

1998-07-01

of the Basic Automation System (BAS) and Coke Production Management System (CPMS). BAS provides real time data for operators to help them run the process stably. CPMS is a supporting system for BAS and operators. With help of CPMS operators define the set points for BAS. The BAS consists of the Digital Process Automation System which controls the coke oven battery heating system and coal to coke conversion and the Programmable Logic System which controls the coke oven machines. The Data transmission between the machines and the host computer is based on a radio link system. Adopting Giprokoks battery design, improving the process mechanically, taking modern automation and expertized heating control system into use have proven to be an economically, technically and environmentally sound solution for Rautaruukki Steel. The structure and basic principles of the new heating control system had been proven functioning very well during eight months period after commissioning and guiding operators uniformly. The dynamic scheduling model had make it easier to operate battery machines in different operation situations.

Effect of oxygen potential on sulphur dioxide activation of oil sands fluid coke and characteristics of activated coke in mercury adsorption

International Nuclear Information System (INIS)

Morris, E.A.; Jia, C.Q.; Tong, S.

2007-01-01

A sulphur-impregnated activated carbon (SIAC) technology was modified for use in copper smelters in order to mitigate mercury and sulphur dioxide (SO 2 ) emissions. Elemental sulphur was captured as a co-product. The study examined the feasibility of reducing levels of SO 2 using fluid coke in the copper smelter flue. SIAC properties were optimized in order to capture vapour phase mercury. Raw fluid coke samples were used to measure SO 2 flow rates. Gas composition was varied to mimic concentrations found during normal operation of copper converters. Gas chromatography was used to analyze reactions products and to prove the hypothesis that mercury capacity is influenced by the oxygen potential of the activation gas due to changes in surface sulphur types developed from reduced sulphur species. Results of the study showed that oxygen levels at 5 per cent did not play a significant role in pore development. It was concluded that increased residence times contributed to reductions in SO 2 and elemental S yields. 13 refs., 1 tab., 7 figs

Conversion of different ash content brown coal in fluidized bed

Energy Technology Data Exchange (ETDEWEB)

Osipov, P.; Chernyavskiy, N.; Ryzhkov, A.; Remenuk, A. [Ural Federal Univ., Ekaterinburg (Russian Federation). Dept. of Thermal Power Plants; Dulienko, S. [National Academy of Science of Ukraine, Kiev (Ukraine). Coal Energy Technology Inst.

2013-07-01

Available equations used to determine combustion specific rate of coal-derived cokes describe the burning of carbon particles well enough but are not accurate in case of ash-containing coke particles combustion. This study is an attempt to account for the influence of both initial ash content and its increase in the course of carbon conversion in specific rate calculations. The results of experimental study of burn-out dynamics of Volchanskiy field (North Urals) brown coal and its coke with different ash content under conditions of fluidized bed combustion at impulse-type non-gradient reactor RSC-1 and dynamic installation Pyrolysis-M are summarized. Diffusion and heterogeneous (kinetic) components of carbon combustion rate are identified separately by using diffusion and kinetics equation with correction for carbon mass fraction in particles. Burning particle overheating values and heterogeneous combustion rate constants at different temperatures are estimated.

Quarterly coal report, April 1996--June 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-01

This report provides information about U.S. coal production, distribution; exports, imports, prices, consumption, and stocks. Data on coke production is also provided. This report presents data for April 1996 thru June 1996.

Biological CO2 conversion to acetate in subsurface coal-sand formation using a high-pressure reactor system

Science.gov (United States)

Ohtomo, Y.; Ijiri, A.; Ikegawa, Y.; Tsutsumi, M.; Imachi, H.; Uramoto, G.; Hoshino, T.; Morono, Y.; Tanikawa, W.; Hirose, T.; Inagaki, F.

2013-12-01

The geological CO2 sequestration into subsurface unmineable oil/gas fields and coal formations has been considered as one of the possible ways to reduce dispersal of anthropogenic greenhouse gasses into the atmosphere. However, feasibility of CO2 injection largely depends on a variety of geological and economical settings, and its ecological consequences have remained largely unpredictable. To address these issues, we developed a new flow-through-type CO2 injection system designated as the 'geobio-reactor system' to examine possible geophysical, geochemical and microbiological impact caused by CO2 injection under in-situ pressure (0-100 MPa) and temperature (0-70°C) conditions. In this study, we investigated Eocene bituminous coal-sandstones in the northwestern Pacific coast, Hokkaido, Japan, using the geobio-reactor system. Anaerobic artificial fluid and CO2 (flow rate: 0.002 and 0.00001 mL/min, respectively) were continuously supplemented into the coal-sand column under the pore pressure of 40 MPa (confined pressure: 41 MPa) at 40°C for 56 days. Molecular analysis of bacterial 16S rRNA genes showed that predominant bacterial components were physically dispersed from coal to sand as the intact form during experiment. Cultivation experiments from sub-sampling fluids indicated that some terrestrial microbes could preserve their survival in subsurface condition. Molecular analysis of archaeal 16S rRNA genes also showed that no methanogens were activated during experiment. We also anaerobically incubated the coal sample using conventional batch-type cultivation technique with a medium for methanogens. After one year of the batch incubation at 20°C, methane could be detected from the cultures except for the acetate-fed culture. The sequence of archaeal 16S rRNA genes via PCR amplification obtained from the H2 plus formate-fed culture was affiliated with a hydrogenotrophic methanogen within the genus Methanobacterium, whereas the methanol plus trimethylamine culture

Modified sequential extraction for biochar and petroleum coke: Metal release potential and its environmental implications.

Science.gov (United States)

von Gunten, Konstantin; Alam, Md Samrat; Hubmann, Magdalena; Ok, Yong Sik; Konhauser, Kurt O; Alessi, Daniel S

2017-07-01

A modified Community Bureau of Reference (CBR) sequential extraction method was tested to assess the composition of untreated pyrogenic carbon (biochar) and oil sands petroleum coke. Wood biochar samples were found to contain lower concentrations of metals, but had higher fractions of easily mobilized alkaline earth and transition metals. Sewage sludge biochar was determined to be less recalcitrant and had higher total metal concentrations, with most of the metals found in the more resilient extraction fractions (oxidizable, residual). Petroleum coke was the most stable material, with a similar metal distribution pattern as the sewage sludge biochar. The applied sequential extraction method represents a suitable technique to recover metals from these materials, and is a valuable tool in understanding the metal retaining and leaching capability of various biochar types and carbonaceous petroleum coke samples. Copyright © 2017 Elsevier Ltd. All rights reserved.

Relation of ash composition to the uses of coal

Energy Technology Data Exchange (ETDEWEB)

Fieldner, A C; Selvig, W A

1926-02-01

The effects of coal ash and ash components on the utilization of coal for coke and gas production, steam generation, water gas production, smithing, and domestic uses were described in a review of literature. Calcite, gypsum, and pyrite which occur in high amounts in coal, increase the ash fusibility of the coal and render it unsuitable for many industrial and domestic uses. As a rule, coal ash of high Si content and low Fe content would not be readily fusible. High amounts of ash in coal also have the effect of reducing the heating value of the coal.

Coal 99; Kol 99

Energy Technology Data Exchange (ETDEWEB)

Sparre, C

2000-07-01

The following report deals with the use of coal and coke during 1998. Some information about techniques, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from Statistics Sweden have also been used. The use of steam coal for heating purposes during 1998 was 680 000 tons and somewhat lower than in 1997. The extremely high figures of 1996 were due to twice the production of electricity because of lack of waterpower. The co-generation plants were the main users of coal. The minor plants have increased their use of forest fuels. Probably the use of steam coal will go down in the immediate years both in the heat generating and the co-generating plants. During the top year 1987 coal was used in 18 hot water plants and 11 co-generation plants. During 1998 these figures are 1 and 8. Taxes and environmental reasons explain this trend. The use of steam coal in the industry has been constant at the level 700 000 tons. This level is supposed to be constant or to vary with business cycles. Steel-works, however, increase their use of steam coal in order to replace the more expensive coke. The import of metallurgical coal in 1998 was 1.6 mill tons like the year before. 1.1 mill tons of coke were produced. The coke consumption in the industry was 1.4 mill tons from which 0.3 mill tons were imported. Several other plants have plans to replace the coal with forest fuels, waste fuels and NG. Even the biggest plant, Vaesteraas, has ordered a block for bio fuels. Helsingborg has started to use wood pellets. The pellets replace most of the coal for the heat production in the co-generation plant. Norrkoeping Kraft AB has put a fluid bed boiler for various fuels into operation, leading to more than half the coal consumption compared with previous years. They have also rebuilt one of their travelling grates for bio fuels. Stockholm Energi, Haesselbyverket, has invested

Conversion of metallurgical coke and coal using a Coal Direct Chemical Looping (CDCL) moving bed reactor

International Nuclear Information System (INIS)

Luo, Siwei; Bayham, Samuel; Zeng, Liang; McGiveron, Omar; Chung, Elena; Majumder, Ankita; Fan, Liang-Shih

2014-01-01

Highlights: • Accumulated more than 300 operation hours were accomplished for the moving bed reducer reactor. • Different reactor operation variables were investigated with optimal conditions identified. • High conversions of sub-bituminous coal and bituminous coal were achieved without flow problems. • Co-current and counter-current contact modes were tested and their applicability was discussed. - Abstract: The CLC process has the potential to be a transformative commercial technology for a carbon-constrained economy. The Ohio State University Coal Direct Chemical Looping (CDCL) process directly converts coal, eliminating the need for a coal gasifier oran air separation unit (ASU). Compared to other solid-fuel CLC processes, the CDCL process is unique in that it consists of a countercurrent moving bed reducer reactor. In the proposed process, coal is injected into the middle of the moving bed, whereby the coal quickly heats up and devolatilizes, splitting the reactor roughly into two sections with no axial mixing. The top section consists of gaseous fuel produced from the coal volatiles, and the bottom section consists of the coal char mixed with the oxygen carrier. A bench-scale moving bed reactor was used to study the coal conversion with CO 2 as the enhancing gas. Initial tests using metallurgical cokefines as feedstock were conducted to test the effects of operational variables in the bottom section of the moving bed reducer, e.g., reactor temperature, oxygen carrier to char ratio, enhancer gas CO 2 flow rate, and oxygen carrier flow rates. Experiments directly using coal as the feedstock were subsequently carried out based on these test results. Powder River Basin (PRB) coal and Illinois #6 coal were tested as representative sub-bituminous and bituminous coals, respectively. Nearly complete coal conversion was achieved using composite iron oxide particles as the oxygen carriers without any flow problems. The operational results demonstrated that a

Closed-cycle process of coke-cooling water in delayed coking unit

International Nuclear Information System (INIS)

Zhou, P.; Bai, Z.S.; Yang, Q.; Ma, J.; Wang, H.L.

2008-01-01

Synthesized processes are commonly used to treat coke-cooling wastewater. These include cold coke-cut water, diluting coke-cooling water, adding chemical deodorization into oily water, high-speed centrifugal separation, de-oiling and deodorization by coke adsorption, and open nature cooling. However, because of water and volatile evaporation loss, it is not suitable to process high-sulphur heavy oil using open treatments. This paper proposed a closed-cycling process in order to solve the wastewater treatment problem. The process is based on the characteristics of coke-cooling water, such as rapid parametric variation, oil-water-coke emulsification and steam-water mixing. The paper discussed the material characteristics and general idea of the study. The process of closed-cycle separation and utilization process of coke-cooling water was presented along with a process flow diagram. Several applications were presented, including a picture of hydrocyclones for pollution separation and a picture of equipments of pollution separation and components regeneration. The results showed good effect had been achieved since the coke-cooling water system was put into production in 2004. The recycling ratios for the components of the coke-cooling water were 100 per cent, and air quality in the operating area reached the requirements of the national operating site circumstance and the health standards. Calibration results of the demonstration unit were presented. It was concluded that since the devices went into operation, the function of production has been normal and stable. The operation was simple, flexible, adjustable and reliable, with significant economic efficiency and environmental benefits. 10 refs., 2 tabs., 3 figs

The use of fractionated fly ash of thermal power plants as binder for production of briquettes of coke breeze and dust

Science.gov (United States)

Temnikova, E. Yu; Bogomolov, A. R.; Lapin, A. A.

2017-11-01

In this paper, we propose to use the slag and ash material of thermal power plants (TPP) operating on pulverized coal fuel. The elemental and chemical composition of fly ash of five Kuzbass thermal power plants differs insignificantly from the composition of the mineral part of coking coal because coke production uses a charge, whose composition defines the main task: obtaining coke with the required parameters for production of iron and steel. These indicators are as follows: CRI reactivity and strength of the coke residue after reaction with CO2 - CSR. The chemical composition of fly ash of thermal power plants and microsilica with bulk density of 0.3-0.6 t/m3 generated at production of ferroalloys was compared. Fly ash and microsilica are the valuable raw material for production of mineral binder in manufacturing coke breeze briquettes (fraction of 2-10 mm) and dust (0-200 μm), generated in large quantities during coking (up to 40wt%). It is shown that this binder is necessary for production of smokeless briquettes with low reactivity, high strength and cost, demanded for production of cupola iron and melting the silicate materials, basaltic rocks in low-shaft furnaces. It is determined that microsilica contains up to 90% of silicon oxide, and fly ash contains up to 60% of silicon oxide and aluminum oxide of up to 20%. On average, the rest of fly ash composition consists of basic oxides. According to calculation by the VUKHIN formula, the basicity index of briquette changes significantly, when fly ash is introduced into briquette raw material component as a binder. The technology of coke briquette production on the basis of the non-magnetic fraction of TPP fly ash in the ratio from 3.5:1 to 4.5:1 (coke breeze : coke dust) with the addition of the binder component to 10% is proposed. The produced briquettes meet the requirements by CRI and require further study on CSR requirements.

Fissure formation in coke. 2: Effect of heating rate, shrinkage and coke strength

Energy Technology Data Exchange (ETDEWEB)

D.R. Jenkins; M.R. Mahoney [CSIRO, North Ryde, NSW (Australia). Mathematical and Information Sciences

2010-07-15

We investigate the effects of the heating rate, coke shrinkage and coke breakage strength upon the fissure pattern developed in a coke oven charge during carbonisation. This is done principally using a mechanistic model of the formation of fissures, which considers them to be an array of equally spaced fissures, whose depth follows a 'period doubling' pattern based upon the time history of the fissures. The model results are compared with pilot scale coke oven experiments. The results show that the effect of heating rate on the fissure pattern is different to the effect of coke shrinkage, while the effect of coke breakage strength on the pattern is less pronounced. The results can be seen in both the shape and size of resulting coke lumps after stabilisation. The approach gives the opportunity to consider means of controlling the carbonisation process in order to tune the size of the coke lumps produced. 7 refs., 18 figs., 4 tabs.

Fundamental studies of coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

1995-01-01

The authors have examined the pyrolysis of Argonne samples of Wyodak and Illinois No. 6 coal in argon, undecane, Tetralin, and water. The effects of the pyrolysis on individual particles of coal were monitored visually in a cell with diamond windows capable of operation to temperature and pressures in excess of 500{degrees}C and 3000 psi. The changes in the particles from ambient to 460{degrees}C were recorded in real time on video tape, and images were then taken from the tape record and analyzed. The study showed that in argon both coals developed tars at 350{degrees}-370{degrees}C. The tars then quickly evaporated, leaving core particles remarkably similar in size and shape to the initial particles. These observations suggest that coal does not melt nor become fully liquid when heated. Nor does the softened coal undergo crosslinking to generate coke. Rather the simple loss of volatiles leaves behind the core residue as coke. Contrary to the common view, there appears to be no link between the bond-breaking processes yielding tar and the interaction of the coal with H-donors leading to liquefaction. Water as a medium was surprising in its effect. Both coals began to shrink at 300{degrees}-350{degrees}C, with the effect appearing to be more of an erosion rather than a uniform loss of substance as seen in Tetralin. The Wyodak continued to shrink to 460{degrees}C to about half its initial size. With the Illinois No. 6 coal, however, the process reversed at around 420{degrees}C, and the particles appeared to grow with the evolution of a tar, continuing to 460{degrees}C. The authors submit that this final observation is evidence for hydrothermal synthesis of hydrocarbons at these conditions.

Indian coal tars. II

Energy Technology Data Exchange (ETDEWEB)

Basu, A N; Bhatnagar, J N; Roy, A K

1954-01-01

Laboratory experiments were carried out on these efforts: (1) rank and specific-gravity fractions on tar yield; (2) addition of water to the coal charge, or steam during carbonization, on yield of tar and tar acids; (3) the presence of a cracking agent (shale) with and without steam addition on the yield of tar and tar acids (the particular shale used without steam reduced the yield, and the restricted use of steam brought the yield to the former noncatalyzed level); and (4) catalytic effect of three different samples of shale, firebrick, quartz, coke, and silica-alumina on the cracking of tar acids (the most active were two of the shales, a freshly-prepared coke, and the Al/sub 2/O/sub 3/-SiO/sub 2/ catalysts that gave conversion up to 98%). The products were mainly carbon, aromatic hydrocarbons of the naphthalene series and gases (CO and H/sub 2/). The yield of the tar becomes less as coal of lower specific gravity is used or when higher temperatures are used for carbonization. The mineral matter associated with Indian coals acts as a decomposition catalyst for tar acids, as shown by experiments on the decomposition of PhOH at temperatures above 800/sup 0/.

Monitoring coal conversion processes by IR-spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Hobert, H.; Kempe, J.; Stephanowitz, H. (Friedrich-Schiller-Universitaet, Jena (German Democratic Republic))

1990-01-01

Explains application of infrared spectroscopy combined with multivariate data analysis by an on-line computer system for assessing coal quality and suitability of brown coal for conversion processes. Coal samples were pelletized under addition of KBr and analyzed using an IRF 180 Fourier transform spectrometer in the spectral range of 400 to 2,000 cm{sup -1}. Components of spectra are presented; the oil yield from coal hydrogenation is calculated by regression analysis. Covariance spectra of carbon, organic hydrogen and sulfur are shown. It is concluded that the field of application for the method includes industrial coal liquefaction, gasification as well as briquetting and coking. 8 refs.

Quarterly coal report July--September 1996, February 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-02-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. This report presents detailed quarterly data for July through September 1996 and aggregated quarterly historical data for 1990 through the second quarter of 1996. Appendix A displays, from 1988 on, detailed quarterly historical coal imports data. 8 figs., 72 tabs.

Quarterly coal report, April--June 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience. Coke production, consumption, distribution, imports, and exports data are also provided. This report presents detailed quarterly data for April through June 1997 and aggregated quarterly historical data for 1991 through the first quarter of 1997. Appendix A displays, from 1991 on, detailed quarterly historical coal imports data. Appendix B gives selected quarterly tables converted to metric tons. To provide a complete picture of coal supply and demand in the US, historical information has been integrated in this report. 8 figs., 73 tabs.

Proximate Analysis of Coal

Science.gov (United States)

Donahue, Craig J.; Rais, Elizabeth A.

2009-01-01

This lab experiment illustrates the use of thermogravimetric analysis (TGA) to perform proximate analysis on a series of coal samples of different rank. Peat and coke are also examined. A total of four exercises are described. These are dry exercises as students interpret previously recorded scans. The weight percent moisture, volatile matter,…

Evaluation of ecological consequences of coal mine closure in Kuzbass coal region

International Nuclear Information System (INIS)

Schastlivcev, E.L.; Barannic, L.P.; Ovdenko, B.I.; Bykov, A.A.

2000-01-01

Kemerovo region (otherwise called Kuzbass) is the most industrially developed and urbanized region of Siberia, Russia. The main industrial branch of Kuzbass is coal output. Open pits and underground mines of Kuzbass produce about 40% of total amount of coal in Russia and more than 70% of coking coal. In the current process of the coal industry's restructuring, the closing of many unprofitable coal enterprises is associated with radical changes in their influence on the environment. The task to provide a probable forecast of ecological consequence of mine closure is both practically significant and complicated. In order to find some scientific approach to solve named problem the authors made in the paper the first attempts to analyze of accessible closed mines data in Kuzbass, to classify coal mines (working and closed) with respect to there negative influence on soil, water and atmosphere and to obtain some numerical estimates of possible bounds of this influence. 7 refs

Coke, char and organic waste behaviour in the blast furnace with high injection rate

Directory of Open Access Journals (Sweden)

Gudenau, H. W.

2003-10-01

Full Text Available Blast furnace operation with low coke rate, high amount of auxiliary hydrocarbons and use of nut coke causes a change in coke quality requirements. In particular, not burned in the raceway residues of injected substances (char and ash can influence the coke behaviour. Therefore combustion efficiency of various organic wastes with and without pulverized coal injection (PCI and coal char has been investigated under the raceway simulation conditions. Mixing of various substances improves their combustion efficiency. Study on coke gasification by carbon dioxide in the presence of char showed that with the increase of char concentration, coke strength reduction becomes smaller. The reactivity of char with CO₂ is higher than that of coke. Therefore char is consumed preferentially. In presence of injected char, total pore volume in coke and its wear resistance were increased. Coke reactivity and microstructure in the presence of various kinds of ash has been studied. Many ash spheres were observed on the surface of coke matrix and its size was dependent on ash properties.

La operación del horno alto con una tasa baja de coque, una cantidad elevada de hidrocarburos auxiliares y el empleo de coque calibrado, origina un cambio en las necesidades de calidad del coque. En particular, pueden influir en el comportamiento del coque los residuos inquemados en el raceway (cavidad enfrente a las toberas del horno de las sustancias que se inyectan (char y cenizas. El char es el residuo de carbón que se origina después que el carbón libera sus sustancias volátiles. Por tanto, se ha investigado la eficiencia de la combustión de varios residuos orgánicos con y sin inyección de carbón pulverizado (ICP y char, bajo las condiciones de simulación del raceway. La mezcla de varias sustancias mejora la eficiencia a la combustión. El estudio de la gasificación del coque por el dióxido de carbono en la

Environmental care in coal combustion

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

Kvaerner Power will supply a CYMIC{reg_sign} circulating fluidized bed (CFB) boiler with a 63 MW electricity capacity to Manitowoc Public Utilities, in Manitowoc, Wisconsin, USA in 2006. This boiler is designed to burn bituminous coal and petroleum coke, with minimised emissions of SO{sub 2} and NOx. Kvaerner Power CFBs are capable of burning either coal or biomass (eg paper pellets) in any combination. Recent deliveries, to Indonesia and China as well as the USA, are listed. 1 tab., 5 photos.

46 CFR 148.04-15 - Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture).

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture). 148.04-15 Section 148.04-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... Requirements for Certain Material § 148.04-15 Petroleum coke, uncalcined; petroleum coke, uncalcined and...

Chemical coal conversion yesterday, today, and tomorrow; Der Chemierohstoff Kohle: gestern, heute und morgen

Energy Technology Data Exchange (ETDEWEB)

Talbiersky, J. [UCP Chemicals AG, Wien (Austria)

2007-01-15

Shortage in mineral oil and gas as well as a high price level have caused a renaissance in coal conversion technologies, at the end of the 70's. Today we have a similar situation. Now coal coversion technologies will be in the focus again but hopefully as a longterm strategy. The most important coal conversion technologies as liquefaction, gasification, coking and calcium carbide synthesis are discussed regarding their use for the production of chemicals. The most important source for aromatic chemicals from coal is till now coal tar with an availability of 22 Mio. t/a. The manufacturing of coal tar is discussed as an example for making aromatic products from a complex feed stock that you get by the fixed bed gasification, coal liquefaction and coking. Also the special marketing strategy that is necessary to be competitive against products from the petroindustry. It can be expected, that coal gasification as a source for synthesis gas will become more and more important. Synthesis gas is the access to aliphatic hydrocarbons by Fischer Tropsch synthesis and to methanol, a chemical with a high synthetic potential. Also the new hydrothermal carbonization of biomass to synthetic coal is mentioned. (orig.)

Changes in thermal plasticity of low grade coals during selective extraction of metals

Directory of Open Access Journals (Sweden)

В. Ю. Бажин

2016-08-01

Full Text Available As the world oil market tends to be highly volatile, the coal becomes a primary source of organic raw materials for chemical and metallurgical industries. Fossil coals can accumulate high amounts of elements and mixtures quite often reaching commercially valuable concentrations. Reserves of scandium and other rare elements in coal deposits in Siberia alone are sufficient to satisfy the expected global demand for several decades. This study is intended to solve complex tasks associated with extraction of metal oxides using the developed enrichment method to ensure the required thermal plasticity determining the quality and properties of metallurgical coke.Laboratory experiments have been conducted for the enrichment of high-ash coals containing the highest concentrations of metals. Thermal plasticity values have been determined with the help of Gieseler plastometer . Using modern technologies and equipment individual deposits can be turned into profitable production of enriched coking coals with concurrent extraction of rare metals. It has been proven that the highest commercial potential lies with the extraction of scandium and some other rare metals in the form of oxides from the coal.

Effect of Extracted Compositions of Liquefaction Residue on the Structure and Properties of the Formed-coke

Directory of Open Access Journals (Sweden)

Song Yong-hui

2016-01-01

Full Text Available The purpose of this paper is to study the effect of extracted compositions of the de-ash liquefaction residue (D-DCLR on pyrolysis products yields, compressive strength and composition of the formed-coke, which was prepared by co-pyrolysis of the low metamorphic pulverized coal and D-DCLR. The scanning electron microscope (SEM and the Fourier Transform Infrared (FT-IR were used to characterize the morphology and functional group of the formed-coke, respectively. The results showed that the extracted compositions of D-DCLR were heavy oil (HS, asphaltene (A, pre-asphaltene (PA and tetrahydrofuran isolusion (THFIS, whose contents were 5.10%, 40.90%, 14.4%, 39.60%, respectively. During the pyrolysis process, HS was the main source of tar, and HS, A as well as PA were conducive to improve gas yields. The THFIS helped to improve the yield of the formed-coke up to 89.5%, corresponding to the compressive strength was only 147.7N/ball for the coke. A and PA were the key factors affecting the compressive strength and surface structure of the formed-coke. The compressive strength of coke could be up to 728.0N/ball with adding D-DCLR, which reduced by 50% after the removal of A and PA. The FT-IR analysis showed that the types of surface functional groups of the formed-coke were remained the same after co-pyrolysis, but the absorption peak intensity of each functional group was changed.

New structural concept for carbonized coals

Energy Technology Data Exchange (ETDEWEB)

Marzec, A. [Polish Academy of Sciences, Gliwice (Poland). Inst. of Coal Chemistry

1997-07-01

The aim of this study was to present a model of structure for solid products of bituminous coal carbonization carried out at end temperatures (ETCs) in the 600-750{degree}C range. The products are of interest since they are used as raw materials for production of activated carbons. Moreover a layer of such products occurring in coke ovens seems to play a crucial role in generation of excessive coking pressure in industrial coking. The experimental data used in modeling were derived from the following: carbonization studies of coals and individual aromatic hydrocarbons, X-ray diffraction, transmission electron microscopy, pyrolysis-field ionization mass spectrometry, and electrical resistivity measurements. The final step of model preparation relied on application of computational chemistry for search of stable conformers and for calculations of molecular orbitals. According to the model, semicokes contain two structural components: (1) oligomers that form nonplanar 3D networks of aromatic clusters (an extended system of conjugated {pi}-orbitals unites clusters of the networks despite the fact they are not coplanar) and (2) planar aggregates that arise from products of dehydrocyclization reaction (the aggregates fill space between oligomeric networks). The two structural components represent optically isotropic and anisotropic phases, respectively. 21 refs., 7 figs.

Pace studying worldwide coke production

International Nuclear Information System (INIS)

Anon.

1993-01-01

Pace Consultants Inc., Houston, has started a multiclient study of world-wide petroleum coke production, examining environmental initiatives and eventually forecasting prices of fuel grade coke. Pace expects coker expansions, increased operating severity, and reduced cycle times to boost coke supply to more than 50 million metric tons/year in 2000, compared with 39.7 million metric tons in 1992. Increased supply and tightened environmental rules in countries consuming large amounts of petroleum coke will be the main factors affecting coke markets. The paper discusses coke quality and the Japanese market

US and world coal trade

Energy Technology Data Exchange (ETDEWEB)

Stevens, B

1988-07-01

This paper reviews the US's coal trade with other countries in the world. Despite being pressed to support domestic coal producers, US utilities are looking towards Colombia for more of their supplies. Whilst the amount of Colombian coal imported into the US is small, it is a combination of this and coal imported from Australia, Canada and China which is causing concern. Studies indicate that the volume of coal imported into the US may rise to 3 Mt/year within three years. Coal exports may suffer if Brazil bans the import of significant quantities of US coking coal in retaliation against American trade sanctions against Brazilian computer import barriers. Also, Romania is expected to impose tariffs on US imports which will have an impact on US coal exported to Romania. US remains the top coal exporter to the European Communities but its lead was cut back due to a big rise of Australian export. A portion of EC market has also been lost to the USSR and Poland. Meanwhile, Japan is resisting buying US's steam coal because it is too expensive.

The shell coal gasification process

Energy Technology Data Exchange (ETDEWEB)

Koenders, L.O.M.; Zuideveld, P.O. [Shell Internationale Petroleum Maatschappij B.V., The Hague (Netherlands)

1995-12-01

Future Integrated Coal Gasification Combined Cycle (ICGCC) power plants will have superior environmental performance and efficiency. The Shell Coal Gasification Process (SCGP) is a clean coal technology, which can convert a wide range of coals into clean syngas for high efficiency electricity generation in an ICGCC plant. SCGP flexibility has been demonstrated for high-rank bituminous coals to low rank lignites and petroleum coke, and the process is well suited for combined cycle power generation, resulting in efficiencies of 42 to 46% (LHV), depending on choice of coal and gas turbine efficiency. In the Netherlands, a 250 MWe coal gasification combined cycle plant based on Shell technology has been built by Demkolec, a development partnership of the Dutch Electricity Generating Board (N.V. Sep). The construction of the unit was completed end 1993 and is now followed by start-up and a 3 year demonstration period, after that the plant will be part of the Dutch electricity generating system.

Basinal analysis of the Ecca and Lowermost Beaufort Beds and associated coal, uranium and heavy mineral beach sand occurrences

International Nuclear Information System (INIS)

Ryan, P.J.; Whitfield, G.G.

1979-01-01

The regional sediment transport directions, major provenance areas and the controlling palaeotectonic and palaeogeographic frameworks of sedimentation have been reconstructed for the Great Karoo Basin during the Permian. Analyses of this magnitude can be useful in regional exploration programmes for coal, uranium and fossil heavy mineral beach sand deposits. The strong palaeogeographic control on coal deposition is demonstrated by the fact that some of the most important deposits accumulated in topographically low lying areas on the pre-Karoo surface. Such areas formed sheltered environments ideal for the growth and accumulation of organic material. Elsewhere relatively slow rates of subsidence of a broad, protected, low lying delta plain controlled the deposition of coal. North of the main Karoo Basin many of the coal deposits are confined to structurally controlled linear basins. Hundreds of sedimentary uranium occurrences of varying grade and size occur within a broad, discontinuous belt in the Lower Beaufort of the southwestern portion of the Karoo Basin. The uranium mineralization occurs in a variety of fluvial deposits usually rich in carbonaceous material. Minute tuffaceous fragments, reflecting contemporaneous vulcanism, form a minor but significant constituent in some of the uraniferous sandstones. The uranium occurrences are confined largely to the Southern and Western Facies of the Lower Beaufort, and occur mainly within the confines of the Karoo Trough. Consolidated heavy mineral beach deposits have been found in the predominantly fluvio-deltaic Middle Ecca Group of the Northern Facies at a number of widely separated locations. These deposits were formed by shore line processes, such as the reworking of delta-front sands, during periods of temporary marine regression

Viscosity change of coal during carbonization; Sekitan tanka hannochu no nendo henka

Energy Technology Data Exchange (ETDEWEB)

Matsuoka, K.; Hayashi, J.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

1996-10-28

In relation to softening, melting and solidification of coal during heating, the effect of heating rate and nitrogen gas pressure on viscosity change, and change with time in the yield of pyridine extract were measured to study the mechanism of viscosity change. In experiment, six kinds of coals were used, and their needle penetration and dilatation were measured using compacted disk coal pellets. The coking and slight coking coal heat-treated under the same condition as the above experiment were used for pyridine extraction. As the experimental result, the apparent viscosity during coal heating was dependent on heating rate, nitrogen pressure and coal kinds. The minimum apparent viscosity decreased with an increase in heating rate and nitrogen pressure, and approached to a constant value. Like apparent viscosity change, the yield of pyridine extract was also dependent on heating rate, and its temperature range nearly agreed with that of apparent viscosity change. It was suggested that the viscosity is dependent on not only the mass fraction of plastic intermediate but also temperature and the relation between plastic intermediate and other components. 3 refs., 5 figs., 1 tab.

Analysis of hard coal quality for narrow size fraction under 20 mm

Science.gov (United States)

Niedoba, Tomasz; Pięta, Paulina

2018-01-01

The paper presents the results of an analysis of hard coal quality diversion in narrow size fraction by using taxonomic methods. Raw material samples were collected in selected mines of Upper Silesian Industrial Region and they were classified according to the Polish classification as types 31, 34.2 and 35. Then, each size fraction was characterized in terms of the following properties: density, ash content, calorific content, volatile content, total sulfur content and analytical moisture. As a result of the analysis it can be stated that the best quality in the entire range of the tested size fractions was the 34.2 coking coal type. At the same time, in terms of price parameters, high quality of raw material characterised the following size fractions: 0-6.3 mm of 31 energetic coal type and 0-3.15 mm of 35 coking coal type. The methods of grouping (Ward's method) and agglomeration (k-means method) have shown that the size fraction below 10 mm was characterized by higher quality in all the analyzed hard coal types. However, the selected taxonomic methods do not make it possible to identify individual size fraction or hard coal types based on chosen parameters.

Comparison of 3 MeV C+ Ion-Irradiation Effects between The Nuclear Graphites made of Pitch and Petroleum Cokes

International Nuclear Information System (INIS)

Se-Hwan, Chi; Gen-Chan, Kim; Jong-Hwa, Chang

2006-01-01

Currently, all the commercially available nuclear graphite grades are being made from two different cokes, i.e., petroleum coke or coal-tar pitch coke, and a coal-tar pitch binder. Of these, since the coke composes most of the graphite volume, i.e., > 70 %, it is understood that a physical, chemical, thermal, and mechanical property as well as an irradiation-induced property change will be strongly dependent on the type of coke. To obtain first-hand information on the effects of the coke type, i.e., petroleum or pitch, on the irradiation sensitivity of graphite, specimens made of IG-110 of petroleum coke and IG-430 of pitch coke were irradiated up to ∼ 19 dpa by 3 MeV C + at room temperature, and the irradiation-induced changes in the hardness, Young's modulus, Raman spectrum, and oxidation properties were characterized. Results of the TEM show that the size and density of the Mrozowski cracks appeared to be far larger and higher in the IG-110 than the IG-430. Results of the hardness test revealed a slightly higher increase in the IG-430 than the IG-110 by around 10 dpa, and the Raman spectrum measurement showed a higher (FWHM) D /(FWHM) G value for IG-430 for 0.02 ∼ 0.25 dpa. Both the hardness and Raman measurement may imply a higher irradiation sensitivity of the IG-430 than the IG-110. Results of the Young's modulus measurements showed a large data scattering, which prevented us from estimating the differences between the grades. Oxidation experiments using a TG-DTA under a flow of dry air/He = 2.5 % (flow rate: 40 CC/min) at 750 and 1000 deg C show that the IG-110 of the petroleum coke exhibits a far higher oxidation rate than the IG-430. The discrepancy between the oxidation rate of the two grades increased with an increase in the oxidation temperature and the dose. Oxidized surface pore area was larger for IG-110. Judging from the results obtained from the present experimental conditions, the irradiation sensitivity appeared to be dependent on the degree

Solar thermochemical production of syngas from petroleum coke: feasibility study for injection of coke slurries

International Nuclear Information System (INIS)

Vidal, A.; Romero, M.; Kritter F; Steinfeld A

2006-01-01

The steam-gasification of pet-coke using concentrated solar radiation is proposed as a viable alternative to solar hydrogen production. Pet-coke is major solid byproduct from the processing of heavy and extra-heavy oils using delay-coking technology. This report summarizes the major accomplishments to develop a cheap and efficient feeding of petroleum coke by coke water slurries without the need of a carrier gas. The samples were Delayed coke of different grain sizes, in particular from 1,8 to 200 mm (as received). In order to analyse the flow properties of the slurries, some tests were conducted to measure the viscosity of the samples. Then, the pet-coke water slurries were injected into the reactor to study the gasification process. In these experiments, some operational parameters were: molar ratio from 2 to 3 (water/coke), temperature up to 1000 C, residence times from 5 to 9 s. In those conditions, the coke is converted primarily to CO, H 2 , CO 2 and small amounts of methane. Concentration of outlet gases of about 30-50 of H 2 ; 15-20 of CO, 10-15 CO 2 , 1-2% CH 4 were obtained with X coke ∼ 65 to 85%. (authors)

Environmental Policy Induced Input Substitution? The Case of Coking and Steam Coal

OpenAIRE

Ian Lange

2007-01-01

The Clean Air Act of 1990 initiated a tradable permit program for emissions of sulfur dioxide from coal-fired power plants. The effect of this enlightened policy on the coal industry was a large increase in consumption of low-sulfur bituminous and subbituminous coals. Low-sulfur bituminous coal is most attractive to coal-fired power plants as they have higher heat content and require less alteration to the boiler to burn as effectively the coal previously in use. However, low-sulfur bituminou...

Basic characteristics of new shape formed coke in burden distribution; Shingata seikei cokes no sonyu bunpu tokusei

Energy Technology Data Exchange (ETDEWEB)

Ichida, M; Yamamoto, T; Komaki, I; Oda, H; Matsunaga, S; Matsuzaki, S; Deno, T; Konno, N [Nippon Steel Corp., Tokyo (Japan)

1996-12-01

Basic characteristics in burden distribution and charging pattern of new shape formed coke developed in order to improve the properties of small size and low void fraction that pillow-type formed coke h s were conducted by 1/3 scale charging model and mathematical model of blast furnace. Basic characteristics, those are, inclination angle, coke-collapse and trajectory of new shape formed coke are almost the same as those of conventional coke. In the case of wall charging of new shape formed coke, until 60% of total charged coke, new shape formed coke is able to be charged without it`s rolling to the center. It is possible to apply RABIT model to new shape formed coke charging without it`s major modification. In the case of new shape formed coke wall charging, the fluctuation in furnace is supposed to be smaller than that in the case of pillow-type formed coke wall charging. Moreover, it`s center charging is supposed to be applied to actual blast furnace. More accurate estimation of in-furnace phenomena by mathematical model considering coke reactivity, is a subject to be worked out in future. 11 refs., 9 figs., 5 tabs.

Japanese steel mills update and expectations to Canadian coal industry

International Nuclear Information System (INIS)

Yamaguchi, I.

2008-01-01

Kobe Steel's (Kobelco) corporate strategy includes expanding from only-one product such as high tensile strength steel sheet, and enlarging overseas production capacity through joint ventures and technical alliances. A new steel making process from low quality iron ore and steaming coal called ITmk3 has been developed by Kobe Steel that does not require any coke, reduces carbon dioxide emissions by 20 per cent, and reduces the cost of transporting slag. This strategy and technology was presented along with the changes surrounding the Japanese steel industry and raw materials market. These changes include the rise of emerging oil-producing countries; world steel production and exports; the rise in prices of resources; and the slowdown of the United States economy. The current situation of Japanese crude steel production, pig-iron production, and coke expansion plans were also presented. The presentation also outlined expectation's of the Canadian coal industry with reference to Canadian coal imports to Japan. tabs., figs

Quarterly coal statistics of OECD countries

Energy Technology Data Exchange (ETDEWEB)

1992-04-27

These quarterly statistics contain data from the fourth quarter 1990 to the fourth quarter 1991. The first set of tables (A1 to A30) show trends in production, trade, stock change and apparent consumption data for OECD countries. Tables B1 to B12 show detailed statistics for some major coal trade flows to and from OECD countries and average value in US dollars. A third set of tables, C1 to C12, show average import values and indices. The trade data have been extracted or derived from national and EEC customs statistics. An introductory section summarizes trends in coal supply and consumption, deliveries to thermal power stations; electricity production and final consumption of coal and tabulates EEC and Japanese steam coal and coking coal imports to major countries.

NMR spectroscopy of coal pyrolysis products

Energy Technology Data Exchange (ETDEWEB)

Polonov, V.M.; Kalabin, G.A.; Kushnarev, D.F.; Shevchenko, G.G.

1985-12-01

The authors consider the scope for using H 1 and C 13 NMR spectroscopy to describe the products from coal pyrolysis and hydrogenization. The accuracy of the structural information provided by the best NMR methods is also considered. The stuctural parameters derived from H 1 and C 13 NMR spectra are presented. Results demonstrate the high accuracy and sensitivity of the structural information provided by H 1 AND C 13 NMR spectra for coal products. There are substantial structural differences between the soluble products from medium-temperature coking of Cheremkhov coal and high-speed pyrolysis of Kan-Acha coal, and also differences in behavior during hydrogenation. These differences are related to the structure of the organic matter in the initial coal and to differences in the pyrolysis mechanisms.

Desulfurization and denitrogenation in copyrolysis of coal with hydrogen-rich gases

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Li, B.; Zhang, B. [Chinese Academy of Sciences, Taiyuan (China). Institute of Coal Chemistry

1999-06-01

Desulfurization and denitrogenation were systematically investigated by analyzing the chars and tars from copyrolysis of Yanzhou high sulfur bituminous coal with coke-oven gas (COG), synthesis gas (SG) and hydrogen. The results indicated that under the conditions of 3MPa, up to 650{degree}C with a heating rate of 10{degree}C/min, the desulfurization of coal pyrolysis with COG, SG and hydrogen were almost equal (about 80%, w%, ad), the order of denitrogenation were: hydrogen (41%) {gt} SG(35%) {gt} COG(30%). The distributions of sulfur in char, oil and gas was very similar under the three reactive gases, i.e., about 205 in char, 105 in tar and 70% (diff.) in gas, respectively. Compared with hydropyrolysis at the same hydrogen partial pressure, the desulfurization of coal pyrolysis with coke oven gas was increased by about 4.5%, while the denitrogenation was decreased by about 3.5%. There is an important desulfurization advantage for hydropyrolysis using COG and SG instead of pure hydrogen. Compared with the copyrolysis of coal with COG, Yanzhou coal pyrolysis under SG can achieve the same level of desufurization but higher denitrogenation. 11 refs., 3 figs., 4 tabs.

Outlook for the Australian coal market

International Nuclear Information System (INIS)

Anon.

1990-01-01

A shortage of bituminous coal is now being witnessed on the world market, which stems from an increase in demand for it. The prices for bituminous coal, which have been increasing since 1988, will continue to rise in 1990. World coal production in 1989/1990 has been estimated by the Australian Bureau of Mineral Resources at 3,370 million tons, which is 50 million tons more than in the preceding year. Australian experts predict a doubling in world demand for coal by 2025. Many Australian coal mining companies, counting on the increased demand in the future, are taking measures to consolidate production and strengthen their financial base in order to accelerate development of new fields or expand production at existing mines. It is expected that the highest rates of growth in demand will be for power coal. Because of increased world production of steel the demand for coking coal will also rise, but the rates of growth will be much lower than for power coal

Coal in the Mediterranean

International Nuclear Information System (INIS)

Sore, J.C.; Coiffard, J.

1992-01-01

Mediterranean countries are not traditionally coal producers. In France, the main mines were located in the North and East, and belonged to the great coal fields of northern Europe. Spain is a modest producer (ten million tonnes), as is Turkey with its three million tonnes. The only way most of these mines can stand up to international competition is by an array of protectionistic measures and subsidies. This state of affairs has marked events of quite another nature, as it relates to energy economics. That is, coal has taken on increasing importance in the energy supplies of all the countries of the Mediterranean zone over the past twenty years. In this article, we set out by describing coke supply for the Mediterranean ensemble, and then go on to analyze the development aspects of coal for electrical production, the future of Mediterranean lignite, and the supply of imported coal. 4 refs., 11 figs., 3 tabs

Change in pore structure of coals by activation with KOH; KOH fukatsushita sekitan no saiko kozo

Energy Technology Data Exchange (ETDEWEB)

Maruyama, K.; Yoshizawa, N.; Ishikawa, E.; Kobayashi, M.; Toda, Y.; Yamada, Y.; Shiraishi, M. [National Institute for Resources and Environment, Tsukuba (Japan)

1996-10-28

Three typical Japanese coals of non-coking coal, coking coal and anthracite were heat-treated with KOH, and change in their pore structure was examined by absorption of N2, X-ray diffraction and TEM observation. In addition, the relation between a coal rank and pore structure was also studied by absorption experiment of N2. In experiment, the mixture of coal and KOH in a nickel holder was heat-treated in N2 gas flow at heating rate of 2{degree}C/min, and held at a fixed temperature for one hour. To clarify the pore structure, N2 absorption isotherms were measured at -196{degree}C under nearly 76cmHg using a commercially available full-automatic absorption measurement equipment. Based on the X-ray diffraction and TEM observation results on activated coals, the relation between the N2 absorption and pore structure was studied. The results are summarized as follows: (1) The yield and absorption ability of coals increase with a coal rank, (2) The specific surface area of coals reaches its peak at 800{degree}C in activation temperature regardless of a coal rank, and (3) The activation behavior of coals is dependent on a coal rank. 5 refs., 7 figs., 1 tab.

A systematic investigation of SO2 removal dynamics by coal-based activated cokes: The synergic enhancement effect of hierarchical pore configuration and gas components

Science.gov (United States)

Sun, Fei; Gao, Jihui; Liu, Xin; Tang, Xiaofan; Wu, Shaohua

2015-12-01

For the aim to break through the long-term roadblock to porous carbon based SO2 removal technology, typical coal-based activated cokes differing in terms of surface area, pore configuration and surface functional properties, were employed to investigate the SO2 removal dynamics. Among the employed activated cokes, the one with a hierarchically porous structure greatly enhanced the SO2 removal dynamics under the simulated flue gas compositions. More detailedly, SO2 separate adsorption property under normal temperature and pressure evidenced that monolayer SO2 molecules anchoring on micropore surface is the main adsorption pattern. The catalytic oxidation of SO2 follows the Eley-Rideal mechanism by which SO2 was firstly oxidized by molecular oxygen into SO3 which could depart partially to release the active sites for further adsorption. For the role of hierarchical pore configuration, it was proposed that micropores serve as gas adsorption and reaction accommodation, meso-/macropores act as byproduct H2SO4 transport and buffing reservoirs, which may in turn gives rise to the recovery of active sites in micropores and guarantees the continuous proceeding of sulfur-containing species transformation in the micropores. The present results suggest that pore configuration or interconnecting pattern, but not mere surface area or pore volume, should be favourably considered for optimizing heterogeneous gas-solid adsorption and reaction.

Engineering solutions to improve environmental characteristics of coke-chemical industry

Energy Technology Data Exchange (ETDEWEB)

Lavrov, K G; Cherkashina, O I; Pushkarev, G P; Pakhomov, V A; Florinskii, N V; Oleinik, K P; Likhogub, E P; Dorfman, G A; Gorelik, Ya L; Vorona, V K

1979-06-01

In future projects consideration will be given to reduction of air and water pollution. Escape of dust from coke-batteries and coal preparation plants will be stopped by using hermetic enclosures with aspirators. Effluent gases and vapours will be curbed by using more efficient scrubbers and flare systems. Effluent waters will be treated at two-stage flotation stations and recycled to 95% as cooling and utility water. Cooling water consumption will be reduced by the use of air coolers. Pollution monitoring will be improved.

Economic statistics for the mining and metallurgical industries - 1978 and 1979

Energy Technology Data Exchange (ETDEWEB)

Medaets, J.

1982-04-01

The statistics are compiled in 5 sections : 1) The mining industries (coal, metallurgy, quarries and associated industries); 2) The manufacture of coke and briquettes; 3) Iron and steel; 4) Hydrology; and 5) The extraction of sand on Belgium's 'continental shelf'.

Low-temperature carbonization of bituminous coal for the production of solid, liquid, and gaseous fuels

Energy Technology Data Exchange (ETDEWEB)

1942-01-01

Properties and uses of low-temperature coke for producing ferrosilicon, CaC/sub 2/ generator gas and water gas, as a fuel for boilers and household use and as a diluent for coking coal, and the properties and uses of low-temperature tar, gasoline, gas, and liquefied gas are described. By using a circulating gas, it is possible to obtain in low-temperature carbonization of bituminous coal a fuel oil for the navy. Aging-test data of such an oil are given. Several plants in Upper Silesia, using the Lurgi circulation process are producing a fuel oil that meets specification.

Coal - 96

International Nuclear Information System (INIS)

Sparre, C.

1996-09-01

The report deals mainly with coal consumption, but also gives some information about technology, environmental aspects and markets. Data have been collected by questionnaires or via telephone. The use of steam coal for heating was 0.8 Mtons (down 20% from 1994). Cogeneration plants were the main users. Taxes and environmental reasons cause a reduction of the coal use that will probably continue the next years. Use of steam coal in industry has been constant at a level of 0.7 Mtons. The import of metallurgical coal rests constant at a level of 1.6 Mtons. 1.2 Mtons of coke was produced, and 0.3 Mtons imported. The PFBC-plant at Vaertan, Stockholm used 0.13 Mtons of coal, while some coal fired power plants have been converted to peat and wood fuels. The average price of steam coal imported to Sweden in 1995 was 333 SEK/ton, 6% higher than in 1994. The contract prices for delivery 1996 are about the same as at the end of 1995. All cogeneration plants have some sort of SO 2 removal system, mostly wet-dry. The largest plant, at Vaesteraas, has recently invested in a SCR system for NO x removal. Most other plants are using low NO x burners or SNCR systems, based on ammonia or urea, which reduce the emissions 50 - 70%. Some statistic about the world coal market is also given in the report

Radiation-thermal processes of conversion in the coals

International Nuclear Information System (INIS)

Mustafaev, I.I.

2002-01-01

effect in the generation of active hydrocarbons radicals from fuel oil, which play active role in the conversion of organic coal mass to the liquid and gas products. Under the optimal condition ( T=450 degrees centigrade, P=0,1 MPa, τ=20-25 minutes, (Rh/L)=3/1), up to 58% of the cleaned Yeni koy lignites converted to liquid and gaseous products. The fraction of liquid products of Co-pyrolysis of coals with oil fraction at optimal condition is determined. It is obvious that because of the destruction effect of the accelerated electron beam up to 19,2% liquid products are light fractions Tb 0 C. In these conditions, more than 55% sulphur content of the lignites is separated in the form of H 2 S and COS. b)Gasification: The radiation-thermal gasification reactions of various types of carbon (graphite, active coal and semi coke) with H 2 0 and CO 2 have been studied. The radiation effects are essential at the temperatures lower 500 degrees centigrade. It is connected to reactions of decomposition of gasified agents (H 2 O, CO 2 ) and intermediate products of their decomposition (OH, CO 2 * and other). Studies have been made of the formation of H 2 and CO at temperatures between 20 and 700 degrees centigrade on reacting graphite, activated carbon and semi coke with steam and carbon dioxide, respectively, in the presence of gamma radiation. The highest rates of H 2 and CO formation were observed on the gasification of semi coke. Investigation has been made of the temperature of semi coke production from lignite and also of the effect of preirradiation dose on the rate of CO formation in the semi coke/CO 2 system. An increase in the semi coke production temperature from 500 to 700 degrees centigrade reduced its reactivity with carbon dioxide by a factor of 1.4. Preirradiation of the semi coke with 200 kJ/kg decrease the reactivity by a factor of 2.8. A discussion is given of the mechanism of the effect of gamma-radiation on the gasification processes of different carbons in

Emission and profile characteristic of volatile organic compounds emitted from coke production, iron smelt, heating station and power plant in Liaoning Province, China.

Science.gov (United States)

Shi, Jianwu; Deng, Hao; Bai, Zhipeng; Kong, Shaofei; Wang, Xiuyan; Hao, Jiming; Han, Xinyu; Ning, Ping

2015-05-15

107 kinds of C₂-C₁₂ volatile organic compound (VOC) mass concentrations and profiles for four types of coal-fired stationary sources in Liaoning Province were studied by a dilution sampling system and GC-MS analysis method, which are of significant importance with regard to VOC emissions in northeast of China. The results showed that there were some differences among these VOC source profiles. The total mass concentrations of analyzed 107 VOC species varied from 10,917 to 19,652 μg m(-3). Halogenated hydrocarbons exhibited higher mass percentages for the VOC source profiles of iron smelt (48.8%) and coke production plant (37.7%). Aromatic hydrocarbons were the most abundant in heating station plant (69.1%). Ketones, alcohols and acetates held 45.0% of total VOCs in thermal power plant. For non-methane hydrocarbons (NMHCs), which are demanded for photochemical assessment in the USA, toluene and n-hexane were the most abundant species in the iron smelt, coke production and thermal power plant, with the mass percentages of 64.8%, 52.7% and 38.6%, respectively. Trimethylbenzene, n-propylbenzene and o,m-ethyltoluene approximately accounted for 70.0% in heating station plant. NMHCs emitted from coke production, iron smelt, heating station and power plant listed above presented different chemical reactivities. The average OH loss rate of NMHCs from heating station, was 4 to 5.6 times higher than that of NMHCs from iron smelt, coke production and power plant, which implies that VOCs emitted from heating station in northeast of China should be controlled firstly to avoid photochemical ozone pollution and protect human health. There are significant variations in the ratios of benzene/toluene and m, p-xylene/ethylbenzene of these coal-fired source profiles. The representativeness of the coal-fired sources studied and the VOC samples collected should be more closely examined. The accuracy of VOC source profiles related to coal-fired processes is highly dependent on

The application of the coal grain analysis method to coal liberation studies

Energy Technology Data Exchange (ETDEWEB)

O' Brien, G.; Firth, B.; Adair, B. [CSIRO Earth Science & Resource Engineering Brisbane, Qld. (Australia)

2011-07-01

Emerging coal markets such as the use of coal for conversion to liquid fuels and its use in fuels cells and as coal water slurries in diesel engines require coal products with different coal quality specifications than those applicable to traditional coal markets of coke making and conventional power generation. As well as quantifying coals in terms of their chemical and physical properties, detailed knowledge of the mineral inclusions within the coal particles is required to identify coals that are suited to economically produce the low-ash value coals required for these markets. After mining and processing, some particles can consist of essentially pure components of a single maceral or mineral phase whilst others are composite particles that are comprised of varying amounts of macerals and minerals. The proportion of particles that are present as pure components or as composites will be a function of the characteristics of the coal and the particle size. In general, it is considered that size reduction will result in liberation and hence increased yield. The amount of liberation that occurs during crushing or grinding a coal is however coal specific. Particle characterization information provided by an optical microscopic-imaging method, Coal Grain Analysis, was used to identify coals that might benefit from additional crushing to improve recovery of clean coal by new density separation techniques and by flotation. As expected, the results of these studies suggest that the degree of liberation that is obtained is coal specific, and, hence, yield improvements are also coal specific. Hence a quantitative method of investigating this issue is required.

Coke properties in relation to charge preparation techniques. [Selective crushing

Energy Technology Data Exchange (ETDEWEB)

Morozov, O S

1979-01-01

Selective crushing is essential to obtain the required coke properties, so that in the coarse fractions there is a considerable reduction in the middlings and dirt normally difficult to crush. These are at the same time enriched with vitrinite so that there is an increase in the coal substance as such, reflected in improved caking capacity in the coarse size range. Various methods of selective crushing are employed, including air entrainment mills, fluidised bed systems. Other advantages claimed for selective crushing are the uniform pore distribution and air permeability and also the diminished breakage stress.

Dependence of coke properties on the method of charge preparation

Energy Technology Data Exchange (ETDEWEB)

Morozov, O S

1979-04-01

Selective crushing is essential to obtain the required coke properties, so that in the coarse fractions there is a considerable reduction in the middlings and dirt normally difficult to crush. These are at the same time enriched with vitrinite so that there is an increase in the coal substance as such, reflected in improved caking capacity in the coarse size range. Various methods of selective crushing are employed, including air entrainment mills, fluidised bed systems. Other advantages claimed for selective crushing are the uniform pore distribution and air permeability and also the diminished breakage stress.

RESEARCH ON CARBON PRODUCTS FROM COAL USING AN EXTRACTIVE PROCESS

Energy Technology Data Exchange (ETDEWEB)

Peter G. Stansberry; Alfred H. Stiller; John W. Zondlo; Chong Chen; Brian Bland; David Fenton

2002-03-31

This report presents the results of a one-year effort directed at the exploration of the use of coal as a feedstock for a variety of industrially-relevant carbon products. The work was basically divided into three focus areas. The first area dealt with the acquisition of laboratory equipment to aid in the analysis and characterization of both the raw coal and the coal-derived feedstocks. Improvements were also made on the coal-extraction pilot plant which will now allow larger quantities of feedstock to be produced. Mass and energy balances were also performed on the pilot plant in an attempt to evaluate the scale-up potential of the process. The second focus area dealt with exploring hydrogenation conditions specifically aimed at testing several less-expensive candidate hydrogen-donor solvents. Through a process of filtration and vacuum distillation, viable pitch products were produced and evaluated. Moreover, a recycle solvent was also isolated so that the overall solvent balance in the system could be maintained. The effect of variables such as gas pressure and gas atmosphere were evaluated. The pitch product was analyzed and showed low ash content, reasonable yield, good coking value and a coke with anisotropic optical texture. A unique plot of coke yield vs. pitch softening point was discovered to be independent of reaction conditions or hydrogen-donor solvent. The third area of research centered on the investigation of alternate extraction solvents and processing conditions for the solvent extraction step. A wide variety of solvents, co-solvents and enhancement additives were tested with varying degrees of success. For the extraction of raw coal, the efficacy of the alternate solvents when compared to the benchmark solvent, N-methyl pyrrolidone, was not good. However when the same coal was partially hydrogenated prior to solvent extraction, all solvents showed excellent results even for extractions performed at room temperature. Standard analyses of the

Coal washery effluent treatment for material recovery and water reuse

Energy Technology Data Exchange (ETDEWEB)

Banerjee, N.N.; Chaudhuri, M.

1980-10-01

Th effluent from coal washeries consisting mainly of coal fines is normally discharged to inland surface waters and causes severe river pollution with substantial loss of good quality coking coal. The study reported in this paper was undertaken to characterize the effluents from several coal washeries and to evaluate the potential of using various coagulants and coagulant aids for clarification of the effluent with a view to recovery of the coal fines and reuse of the clarified effluent. It has been demonstrated that higher recovery of coal fines can be achieved by using coagulants like alum or ferric chloride with or without coagulant aids with an added advantage of reuse of the clarified effluent in the washery.

Nitrogen Chemistry and Coke Transformation of FCC Coked Catalyst during the Regeneration Process

Science.gov (United States)

Shi, Junjun; Guan, Jianyu; Guo, Dawei; Zhang, Jiushun; France, Liam John; Wang, Lefu; Li, Xuehui

2016-06-01

Regeneration of the coked catalyst is an important process of fluid catalytic cracking (FCC) in petroleum refining, however, this process will emit environmentally harmful gases such as nitrogen and carbon oxides. Transformation of N and C containing compounds in industrial FCC coke under thermal decomposition was investigated via TPD and TPO to examine the evolved gaseous species and TGA, NMR and XPS to analyse the residual coke fraction. Two distinct regions of gas evolution are observed during TPD for the first time, and they arise from decomposition of aliphatic carbons and aromatic carbons. Three types of N species, pyrrolic N, pyridinic N and quaternary N are identified in the FCC coke, the former one is unstable and tends to be decomposed into pyridinic and quaternary N. Mechanisms of NO, CO and CO2 evolution during TPD are proposed and lattice oxygen is suggested to be an important oxygen resource. Regeneration process indicates that coke-C tends to preferentially oxidise compared with coke-N. Hence, new technology for promoting nitrogen-containing compounds conversion will benefit the in-situ reduction of NO by CO during FCC regeneration.

Clean coal initiatives in Indiana

Science.gov (United States)

Bowen, B.H.; Irwin, M.W.; Sparrow, F.T.; Mastalerz, Maria; Yu, Z.; Kramer, R.A.

2007-01-01

Purpose - Indiana is listed among the top ten coal states in the USA and annually mines about 35 million short tons (million tons) of coal from the vast reserves of the US Midwest Illinois Coal Basin. The implementation and commercialization of clean coal technologies is important to the economy of the state and has a significant role in the state's energy plan for increasing the use of the state's natural resources. Coal is a substantial Indiana energy resource and also has stable and relatively low costs, compared with the increasing costs of other major fuels. This indigenous energy source enables the promotion of energy independence. The purpose of this paper is to outline the significance of clean coal projects for achieving this objective. Design/methodology/approach - The paper outlines the clean coal initiatives being taken in Indiana and the research carried out at the Indiana Center for Coal Technology Research. Findings - Clean coal power generation and coal for transportation fuels (coal-to-liquids - CTL) are two major topics being investigated in Indiana. Coking coal, data compilation of the bituminous coal qualities within the Indiana coal beds, reducing dependence on coal imports, and provision of an emissions free environment are important topics to state legislators. Originality/value - Lessons learnt from these projects will be of value to other states and countries.

Kress indirect dry cooling system, Bethlehem Steel's Coke Plant demonstration at Sparrows Point, Maryland. Volume 2. Appendices G-N. Final report, February 1990-February 1992

International Nuclear Information System (INIS)

Ossman, A.G.

1993-05-01

The report provides an evaluation of the Kress Indirect Dry Cooling (KIDC) process. The KIDC process is an innovative system for the handling and cooling of coke produced from a slot type by-product coke oven battery. The report is based on the test work and demonstration of the system at Bethlehem Steel Corporation's Sparrows Point facility in 1991. The report covers both environmental and operational impacts of the KIDC process. The report, Volume 2, contains appendices G-N. Volume 1, PB93-191302, contains the technical report as well as appendices A-F. Volume 2 contains appendixes on coke quality data, blast furnace balwax model report, KIDC operating cost and maintenance requirements, Kress box thickness readings, KIDC coke discharge temperature, QA/QC program, door leak data, and coal data

Experimental and numerical investigations of coke descending behavior in a coke dry quenching cooling shaft

International Nuclear Information System (INIS)

Feng Yanhui; Zhang Xinxin; Yu Quan; Shi Zhongyin; Liu Zhicheng; Zhang Hu; Liu Huafei

2008-01-01

A viscous flow model based on the Navier-Stokes equation is developed to describe coke descending behavior in the 1/7-scaled-down experimental setup of an actual 75 t/h cooling shaft. It is found that the internal friction due to cokes viscosity significantly influences the descending behavior of cokes in the lower part of the shaft, while the external wall friction dominates the sluggish flow of the cokes in the shaft. An asymptotic friction coefficient expression is proposed for granular mixtures flowing along the shaft wall modified from normal wall tress, and the concept of bulk solid viscosity is introduced to describe the internal friction between coke particles. The results simulated by the present model are compared with those by the potential flow and the kinematic model without friction. The viscous flow model is quite good to simulate the bulk coke flow as the physically important frictions are engaged

Abundances of polycyclic aromatic hydrocarbons (PAHs) in 14 chinese and american coals and their relation to coal rank and weathering

Science.gov (United States)

Wang, R.; Liu, Gaisheng; Zhang, Jiahua; Chou, C.-L.; Liu, J.

2010-01-01

The abundances of 16 polycyclic aromatic hydrocarbons (PAHs) on the priority list of the United States Environmental Protection Agency (U.S. EPA) have been determined in 14 Chinese and American coals. The ranks of the samples range from lignite, bituminous coal, anthracite, to natural coke. Soxhlet extraction was conducted on each coal for 48 h. The extract was analyzed on a gas chromatograph-mass spectrometer (GC-MS). The results show that the total PAH content ranged from 0.31 to 57.6 ??g/g of coal (on a dry basis). It varied with coal rank and is highest in the maturity range of bituminous coal rank. High-molecular-weight (HMW) PAHs are predominant in low-rank coals, but low-molecular-weight (LMW) PAHs are predominant in high-rank coals. The low-sulfur coals have a higher PAH content than high-sulfur coals. It may be explained by an increasing connection between disulfide bonds and PAHs in high-sulfur coal. In addition, it leads us to conclude that the PAH content of coals may be related to the depositional environment. ?? 2010 American Chemical Society.

Bright outlook for coal

International Nuclear Information System (INIS)

Anon

2001-01-01

After enduring contract price cuts over the past two years of almost 17% for thermal coal and 23% for hard coking coal, the New South Wales coal industry is looking forward to a reversal of fortune for 2001. Increased export demand, improved prices, significant improvements in mine site productivity, a weak Australian dollar and the probability of a number of new projects or extensions progressing to development are likely to result in an increase in NSW saleable production to around 110 million tonnes (Mt) in 2000-01. Sharply weaker coal prices over the past two years, intensified international competition and the Asian economic downturn had a negative impact on profitability, investment, exports and employment in the NSW coal industry. As a result, the industry has undergone substantial restructuring. The restructuring process has led to a consolidation in ownership, reduced production costs and improved operational efficiency. The outcome is an industry well positioned to take advantage of the positive market conditions and one likely to experience levels of profitability not achieved over the past few years

The certification of the contents (mass fractions) of sulphur in six coals

Energy Technology Data Exchange (ETDEWEB)

Griepink, B; Maier, E A; Wilkinson, H C [CEC, Bruxelles (Belgium)

1990-01-01

This report presents the preparation and the certification of the sulphur content of six coal reference materials: low volatile steam coal (CRM 331), high volatile industrial coal (CRM 332), coking steam coal (CRM 333), anthracite (CRM 334), flame coal (CRM 335) and high volatile steam coal (CRM 336), as well as the homogeneity and stability studies. The analytical work leading to certification is also presented. The certified mass fractions for total sulphur in CRMs 331, 332, 333, 334, 335 and 336 respectively are 4.99 mg/g, 9.61 mg/g, 13.44 mg/g, 16.09 mg/g, 50.8 mg/g and 32.90 mg/g.

PRODUCTION OF CARBON PRODUCTS USING A COAL EXTRACTION PROCESS

Energy Technology Data Exchange (ETDEWEB)

Dady Dadyburjor; Philip R. Biedler; Chong Chen; L. Mitchell Clendenin; Manoj Katakdaunde; Elliot B. Kennel; Nathan D. King; Liviu Magean; Peter G. Stansberry; Alfred H. Stiller; John W. Zondlo

2004-08-31

This Department of Energy National Energy Technology Laboratory sponsored project developed carbon products, using mildly hydrogenated solvents to extract the organic portion of coal to create synthetic pitches, cokes, carbon foam and carbon fibers. The focus of this effort was on development of lower cost solvents, milder hydrogenation conditions and improved yield in order to enable practical production of these products. This technology is needed because of the long-term decline in production of domestic feedstocks such as petroleum pitch and coal tar pitch. Currently, carbon products represents a market of roughly 5 million tons domestically, and 19 million tons worldwide. Carbon products are mainly derived from feedstocks such as petroleum pitch and coal tar pitch. The domestic supply of petroleum pitch is declining because of the rising price of liquid fuels, which has caused US refineries to maximize liquid fuel production. As a consequence, the long term trend has a decline in production of petroleum pitch over the past 20 years. The production of coal tar pitch, as in the case of petroleum pitch, has likewise declined significantly over the past two decades. Coal tar pitch is a byproduct of metallurgical grade coke (metcoke) production. In this industry, modern metcoke facilities are recycling coal tar as fuel in order to enhance energy efficiency and minimize environmental emissions. Metcoke production itself is dependent upon the production requirements for domestic steel. Hence, several metcoke ovens have been decommissioned over the past two decades and have not been replaced. As a consequence sources of coal tar are being taken off line and are not being replaced. The long-term trend is a reduction in coal tar pitch production. Thus import of feedstocks, mainly from Eastern Europe and China, is on the rise despite the relatively large transportation cost. To reverse this trend, a new process for producing carbon products is needed. The process must be

Dispersion modeling of polycyclic aromatic hydrocarbons from combustion of biomass and fossil fuels and production of coke in Tianjin, China.

Science.gov (United States)

Tao, Shu; Li, Xinrong; Yang, Yu; Coveney, Raymond M; Lu, Xiaoxia; Chen, Haitao; Shen, Weiran

2006-08-01

A USEPA, procedure, ISCLT3 (Industrial Source Complex Long-Term), was applied to model the spatial distribution of polycyclic aromatic hydrocarbons (PAHs) emitted from various sources including coal, petroleum, natural gas, and biomass into the atmosphere of Tianjin, China. Benzo[a]pyrene equivalent concentrations (BaPeq) were calculated for risk assessment. Model results were provisionally validated for concentrations and profiles based on the observed data at two monitoring stations. The dominant emission sources in the area were domestic coal combustion, coke production, and biomass burning. Mainly because of the difference in the emission heights, the contributions of various sources to the average concentrations at receptors differ from proportions emitted. The shares of domestic coal increased from approximately 43% at the sources to 56% at the receptors, while the contributions of coking industry decreased from approximately 23% at the sources to 7% at the receptors. The spatial distributions of gaseous and particulate PAHs were similar, with higher concentrations occurring within urban districts because of domestic coal combustion. With relatively smaller contributions, the other minor sources had limited influences on the overall spatial distribution. The calculated average BaPeq value in air was 2.54 +/- 2.87 ng/m3 on an annual basis. Although only 2.3% of the area in Tianjin exceeded the national standard of 10 ng/m3, 41% of the entire population lives within this area.

Determination of electrical resistivity of dry coke beds

Energy Technology Data Exchange (ETDEWEB)

Eidem, P.A.; Tangstad, M.; Bakken, J.A. [NTNU, Trondheim (Norway)

2008-02-15

The electrical resistivity of the coke bed is of great importance when producing FeMn, SiMn, and FeCr in a submerged arc furnace. In these processes, a coke bed is situated below and around the electrode tip and consists of metallurgical coke, slag, gas, and metal droplets. Since the basic mechanisms determining the electrical resistivity of a coke bed is not yet fully understood, this investigation is focused on the resistivity of dry coke beds consisting of different carbonaceous materials, i.e., coke beds containing no slag or metal. A method that reliably compares the electrical bulk resistivity of different metallurgical cokes at 1500{sup o} C to 1600{sup o}C is developed. The apparatus is dimensioned for industrial sized materials, and the electrical resistivity of anthracite, charcoal, petroleum coke, and metallurgical coke has been measured. The resistivity at high temperatures of the Magnitogorsk coke, which has the highest resistivity of the metallurgical cokes investigated, is twice the resistivity of the Corus coke, which has the lowest electrical resistivity. Zdzieszowice and SSAB coke sort in between with decreasing resistivities in the respective order. The electrical resistivity of anthracite, charcoal, and petroleum coke is generally higher than the resistivity of the metallurgical cokes, ranging from about two to about eight times the resistivity of the Corus coke at 1450{sup o}C. The general trend is that the bulk resistivity of carbon materials decreases with increasing temperature and increasing particle size.

A brief petrographic review on Nigerian coal resources

International Nuclear Information System (INIS)

Obaje, N. G.; Abaa, S. I.; Najime, T.; Suh, C. E.

2000-01-01

The coal resources of Nigeria are located mainly within the Benue Trough. In the lower Benue, subbituminous coals occur within the Maastrichtian Mamu Formation. High - volatile bituminous coals are found within the Turonian - Santonian Awgu Formation in the middle Benue while the upper Benue contains lignites and sub-bituminous coals in the Maastrichtian Gombe Sandstone Formation. Maceral analyses show that himinite dominates in the petrographic composition of the lower and upper Benue Trough coals with vitrinite reflectance values ranging from 0.30 to 0.63% Rm. In coals from the middle Benue, vitrinite macerals predominate and Rm values range from 0.74 to 1.25%. The present review suggests that the sub-bituminous coals in the lower and upper Benue are optimum for combustion and sub-optimum for liquefaction; while the high-volatile bituminous coals in the middle Benue, apart form being optimum for liquefaction, are the most suitable as raw material for coke making (carbonization) in steel manufacture

Basic investigations to improve the refinement process of coal. Grundlagenuntersuchungen zur Erhoehung des Veredlungsverhaltens von Kohlen

Energy Technology Data Exchange (ETDEWEB)

Krug, H; Naundorf, W; Trommer, D

1985-01-01

In the four articles in this issue, variants of the process for the effective use and improved refinement of brown coal are described. There are reports on the manufacture of special briquettes from briquette coal slack and on the briquetting behaviour of dry brown coal dust and the briquetting and coking behaviour of hard foreign brown coal containing a lot of ash. The four articles are dealt with separately. With 52 figs., 10 tabs.

Cocaine (Coke, Crack) Facts

Science.gov (United States)

... That People Abuse » Cocaine (Coke, Crack) Facts Cocaine (Coke, Crack) Facts Listen Cocaine is a white ... 69 KB) "My life was built around getting cocaine and getting high." ©istock.com/ Marjot Stacey is ...

Coke gasification costs, economics, and commercial applications

International Nuclear Information System (INIS)

Jahnke, F.C.; Falsetti, J.S.; Wilson, R.F.

1996-01-01

The disposition of petroleum coke remains a problem for modern high conversion refineries. Market uncertainty and the price for coke can prevent the implementation of otherwise attractive projects. The commercially proven Texaco Gasification Process remains an excellent option for clean, cost effective coke disposition as demonstrated by the new coke gasification units coming on-line and under design. Previous papers, have discussed the coke market and general economics of coke gasification. This paper updates the current market situation and economics, and provide more details on cost and performance based on recent studies for commercial plants

Thermal analysis evaluation of the reactivity of coal mixtures for injection in the blast furnace

Directory of Open Access Journals (Sweden)

Maria de Lourdes Ilha Gomes

2006-03-01

Full Text Available Pulverized Coal Injection (PCI is an important standard technology replacing coke partially by pulverized coal into the blast furnace that allows a significant reduction of hot metal costs and environmental impact, contributing to a decrease of coke requirements for ironmaking. Coals typically used in this process in Brazil are, at current time, exclusively imported from many countries, although economic important coal-measures occur in the southern part of the country. The Brazilian coals have a low rank, higher contents of inert components, proportioning nocoking properties and an expected high reactivity. Due to these caractheristics, these coals could be used for injection in the blast furnaces in order to decrease the dependency on high cost imported coals. The efficiency in the combustion and the coal reactivity are considered important parameters in the blast furnace, since a larger amount of char (unburned coal causes severe problems to the furnace operation. The aim of the present work is to compare the reactivity of a south Brazilian coal, obtained from Faxinal mine, with two imported coals and the blends of the Brazilian coal with the imported ones. The reactivity of these coals and their blends were evaluated in a thermogravimetric analyzer. In the experiments, various mass ratios of Faxinal coal and the imported coals were used to compose the blends. The gasification reaction with pure CO2 was conducted under isothermal conditions at 1050 °C and atmospheric pressure. The experimental results show the greater reactivity of the Faxinal coal. The additive behavior was confirmed. The blends with a composition of up to 50% Faxinal coal have parameters according to the usual limits used for PCI.

The impact of liquid-liquid-vapour phase behaviour on coke formation from model coke precusors

Energy Technology Data Exchange (ETDEWEB)

Minicucci, D.; Shaw, J.M. [Univ. of Toronto, Dept. of Chemical Engineering and Applied Chemistry, Toronto, ON (Canada)

2000-08-01

Catalysts used in the hydroprocessing of heavy feedstocks deactivate due to coke deposition. Although the mechanism for coke formation is not fully understood, condensation reactions of polynuclear aromatic compounds present in the feeds are a key aspect. The effect of coke deposition on catalyst performance is typically modelled using accelerated aging agents comprising model coke precursors. Mixtures employed in such studies polynuclear aromatic compounds such as anthracene as the coke precursor, and long chain alkanes such as hexadecane as a diluent. We show in this paper that binary and pseudo binary mixtures of polynuclear aromatic compounds and n-alkanes present TYPE II, TYPE IV, or TYPE III phase behaviour according to the van Konynenburg and Scott (1980) phase projection nomenclature, Incubation periods and the apparent autocatalytic effects associated with coke deposition in such systems are explained through a combination of high temperature phase equilibrium experiments and computations with the model systems n-alkane + anthracene + hydrogen, n-alkane + pyrene + hydrogen, and n-alkane + dibenzo[a,k]chrysene + hydrogen. (au)

Quarterly coal report, October--December 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

The Quarterly Coal Report (QCR) provides comprehensive information about US coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. The data presented in the QCR are collected and published by the Energy Information Administration (EIA) to fulfill data collection and dissemination responsibilities. This report presents detailed quarterly data for october through December 1997 and aggregated quarterly historical data for 1991 through the third quarter of 1997. Appendix A displays, from 1991 on, detailed quarterly historical coal imports data, as specified in Section 202 of the energy Policy and Conservation Amendments Act of 1985 (Public Law 99-58). Appendix B gives selected quarterly tables converted to metric tons. To provide a complete picture of coal supply and demand in the US, historical information has been integrated in this report. 8 figs., 73 tabs.

Study on hydropyrolysis of maceral from Shenmu coal

Energy Technology Data Exchange (ETDEWEB)

Sun, Q.; Li, W.; Chen, H.; Li, B. [Chinese Academy of Sciences, Taiyuan (China). State Key Lab of Coal Conversion

2002-02-01

Hydropyrolysis of maceral concentrates from Shenmu coal was systematically investigated using TGA at final temperature of 900{degree}C with heating rate of 20{degree}C/min under pressure of 0.1Mpa to 3Mpa. The effect of pressure on TG/DTG curve, distribution of elements in semi-cokes and removal of sulfur and nitrogen was investigated. The results indicated that the remarkable weight loss was observed in range from 378{degree}C to 718{degree}C, the peak temperature of the maximum reaction rate was 496{degree}C and 522{degree}C for V-C and F-C respectively, and V-C has larger weight loss rate. With increasing pressure the diffusion of hydrogen increased markedly, which led to increase of weight loss. For the element distribution in the semi-coke, the C content increased, H and O content decreased, while the S content changed little. The desulfurization and denitrogenation also increased with increase in pressure. At pressure of 3 MPa, V-C had higher desulfurization than F-C. With increased pyrolysis pressure, the combustion reactivity of semi-coke first decreased and then increased. V-C semi-coke had higher combustion reactivity than F-C semi-coke under the same conditions. 8 refs., 6 figs., 3 tabs.

Behavior of coke in large blast furnaces

Energy Technology Data Exchange (ETDEWEB)

Nakamura, N