CFD modelling of sampling locations for early detection of spontaneous combustion in long-wall gob areas.

Science.gov (United States)

Yuan, Liming; Smith, Alex C

In this study, computational fluid dynamics (CFD) modeling was conducted to optimize gas sampling locations for the early detection of spontaneous heating in longwall gob areas. Initial simulations were carried out to predict carbon monoxide (CO) concentrations at various regulators in the gob using a bleeder ventilation system. Measured CO concentration values at these regulators were then used to calibrate the CFD model. The calibrated CFD model was used to simulate CO concentrations at eight sampling locations in the gob using a bleederless ventilation system to determine the optimal sampling locations for early detection of spontaneous combustion.

Fate of synthetic musks in a domestic wastewater treatment plant and in an agricultural field amended with biosolids

International Nuclear Information System (INIS)

Yang, J.-J.; Metcalfe, Chris D.

2006-01-01

Synthetic musks are widely used as fragrance ingredients in personal care products, and they enter domestic wastewater treatment plants (WWTPs) through discharges into municipal sewage systems. Samples of aqueous sewage and biosolids collected from the Peterborough Wastewater Treatment Plant (WWTP), Ontario, Canada were analyzed for 11 synthetic musk compounds using GC/MS. The results showed that 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethyl-cyclopenta[g]-2-benzopyrane (HHCB, 173.1 ± 43.4 ng/L) and 7-acetyl-1,1,3,4,4,6-hexamethyl-tetrahydronaphthalene (AHTN, 41.6 ± 15.8 ng/L) were the dominant fragrances in sewage, but other polycyclic musks and nitro musks were present at lower concentrations. The concentrations of HHCB and AHTN in the aqueous phase of the sewage were highly correlated with both BOD 5 and TOC. The overall removal efficiency of synthetic musks from the aqueous sewage in the WWTP ranged from 43.3% to 56.9%, but removal occurred mainly by partitioning into the biosolids. Based on a mass balance model, the daily input and output of HHCB and AHTN in the Peterborough WWTP were 47 g and 46 g, respectively. In an agricultural field amended with biosolids from the Peterborough WWTP, HHCB and AHTN were detected in soil immediately after application at mean concentrations of 1.0 and 1.3 μg/kg, respectively, but concentrations declined relatively rapidly over the next 6 weeks, post-application

Use of Loran-C navigation system to accurately determine sampling site location in an above ground cooling reservoir

International Nuclear Information System (INIS)

Lockwood, R.E.; Blankinship, D.R.

1994-01-01

Environmental monitoring programs often require accurate determination of sampling site locations in aquatic environments. This is especially true when a open-quotes pictureclose quotes of high resolution is needed for observing a changing variable in a given area and location is assumed to be important to the distribution of that variable. Sample site location can be difficult if few visible land marks are available for reference on a large body of water. The use of navigational systems such as Global Positioning System (GPS) and its predecessor, Loran-C, provide an excellent method for sample site location. McFarland (1992) discusses the practicality of GPS for location determination. This article discusses the use of Loran-C in a sampling scheme implemented at the South Texas Project Electrical Generating Station (STPEGS), Wadsworth, Texas

Concentrations and assessment of exposure to siloxanes and synthetic musks in personal care products from China

International Nuclear Information System (INIS)

Lu Yan; Yuan Tao; Wang Wenhua; Kannan, Kurunthachalam

2011-01-01

We investigated the concentrations and profiles of 15 siloxanes (four cyclic siloxanes, D 4 -D 7 ; 11 linear siloxanes, L 4 -L 14 ), four synthetic musks (two polycyclic musks, HHCB and AHTN; two nitro musks, MX and MK), and HHCB-lactone, in 158 personal care products marketed in China. Siloxanes were detected in 88% of the samples analyzed, at concentrations as high as 52.6 mg g -1 ; Linear siloxanes were the predominant compounds. Among synthetic musks, more than 80% of the samples contained at least one of these compounds, and their total concentrations were as high as 1.02 mg g -1 . HHCB was the predominant musk in all of the samples analyzed, on average, accounting for 52% of the total musk concentrations. Based on the median concentrations of siloxanes and musks and the average daily usage amounts of consumer products, dermal exposure rates in adults were calculated to be 3.69 and 3.38 mg d -1 for siloxanes and musks, respectively. - Highlights: → Siloxanes and synthetic musks are determined in personal care products. → Highest siloxane concentration was 52.6 mg g -1 . → Highest musk concentration was 1.02 mg g -1 . → Daily dermal exposure rates of siloxanes and musks were in mg levels. → Dermal exposure is a major pathway of human exposure to siloxanes and musks. - Dermal application of several personal care products is a major source of human exposure to cyclic and linear siloxanes.

Concentrations and assessment of exposure to siloxanes and synthetic musks in personal care products from China

Energy Technology Data Exchange (ETDEWEB)

Lu Yan [School of Environmental Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Wadsworth Center, New York State Department of Health and Department of Environmental Health Sciences, School of Public Health, State University of New York at Albany, Empire State Plaza, PO Box 509, Albany, NY 12201-0509 (United States); Yuan Tao; Wang Wenhua [School of Environmental Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Kannan, Kurunthachalam, E-mail: kkannan@wadsworth.org [Wadsworth Center, New York State Department of Health and Department of Environmental Health Sciences, School of Public Health, State University of New York at Albany, Empire State Plaza, PO Box 509, Albany, NY 12201-0509 (United States); International Joint Research Center for Persistent Toxic Substances, State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China)

2011-12-15

We investigated the concentrations and profiles of 15 siloxanes (four cyclic siloxanes, D{sub 4}-D{sub 7}; 11 linear siloxanes, L{sub 4}-L{sub 14}), four synthetic musks (two polycyclic musks, HHCB and AHTN; two nitro musks, MX and MK), and HHCB-lactone, in 158 personal care products marketed in China. Siloxanes were detected in 88% of the samples analyzed, at concentrations as high as 52.6 mg g{sup -1}; Linear siloxanes were the predominant compounds. Among synthetic musks, more than 80% of the samples contained at least one of these compounds, and their total concentrations were as high as 1.02 mg g{sup -1}. HHCB was the predominant musk in all of the samples analyzed, on average, accounting for 52% of the total musk concentrations. Based on the median concentrations of siloxanes and musks and the average daily usage amounts of consumer products, dermal exposure rates in adults were calculated to be 3.69 and 3.38 mg d{sup -1} for siloxanes and musks, respectively. - Highlights: > Siloxanes and synthetic musks are determined in personal care products. > Highest siloxane concentration was 52.6 mg g{sup -1}. > Highest musk concentration was 1.02 mg g{sup -1}. > Daily dermal exposure rates of siloxanes and musks were in mg levels. > Dermal exposure is a major pathway of human exposure to siloxanes and musks. - Dermal application of several personal care products is a major source of human exposure to cyclic and linear siloxanes.

Metabolism of the polycyclic musk galaxolide and its interference with endogenous and xenobiotic metabolizing enzymes in the European sea bass (Dicentrarchus labrax)

International Nuclear Information System (INIS)

Fernandes, Denise; Dimastrogiovanni, Giorgio; Blázquez, Mercedes; Porte, Cinta

2013-01-01

This study investigates the metabolism and mode of action of galaxolide (HHCB) in the European sea bass -Dicentrarchus labrax- following a single intraperitoneal injection of 50 mg HHCB/kg body weight. In addition, a group of fish was injected with 50 mg/kg of ketoconazole (KCZ), a fungicide that is known to interfere with different Cyp isoenzymes. HHCB was actively metabolised by sea bass and acted as a weak inhibitor of the synthesis of oxyandrogens in gonads of male fish. Both, HHCB and a hydroxylated metabolite were detected in bile. The fungicide ketoconazole was a strong inhibitor of Cyp11β and Cyp3a-catalyzed activities. The work contributes to the better understanding of the impact of synthetic musks on fish and proposes the determination of HHCB and/or its hydroxylated metabolite in bile as a tool to assess environmental exposure in wild fish. -- Highlights: ► The metabolism and mode of action of galaxolide has been investigated in sea bass. ► A hydroxylated metabolite was for the first time identified in fish bile. ► EROD and BCOD activities were not altered by galaxolide exposure. ► Galaxolide decreased moderately the synthesis of oxyandrogens in testes. -- HHCB is actively metabolised by sea bass and acts as a weak inhibitor of the synthesis of oxyandrogens in gonads of male fish

Synthetic Musk fragrances in Trout from Danish fish farms and human milk

DEFF Research Database (Denmark)

Duedahl-Olesen, Lene; Cederberg, Tommy Licht; Pedersen, K. H.

2005-01-01

Synthetic musk compounds used in detergents and cosmetics include nitro and polycyclic musk compounds. These compounds are discharged after use via domestic wastewater and sewage treatment plants to the aquatic environment. Quantitative detection of nitro musk and polycyclic musk compounds by GC....../HRMS in Danish farmed trout and human milk from primiparous mothers are reported. The polycyclic musk, HHCB, dominated the synthetic musk compounds found in trout samples from 1999 with a median concentration of 5.0 mu g/kg fresh weight (n.d.-52.6 mu g/kg fresh weight) and in trout samples collected in 2003....../kg fresh weight in 1999 and to a median less than the detection limit (0.23 mu g/kg fresh weight) in 2003. HHCB also dominated in Danish human milk samples collected in 1999 with a median concentration of 147 mu g/kg fat (38.0-422 mu g/kg fat). Human dietary intake assessment and body burden calculations...

Inputs and distributions of synthetic musk fragrances in an estuarine and coastal environment; a case study

International Nuclear Information System (INIS)

Sumner, Nicola R.; Guitart, Carlos; Fuentes, Gustavo; Readman, James W.

2010-01-01

Synthetic musks are ubiquitous contaminants in the environment. Compartmental distributions (dissolved, suspended particle associated and sedimentary) of the compounds throughout an axial estuarine transect and in coastal waters are reported. High concentrations of Galaxolide (HHCB) and Tonalide (AHTN) (987-2098 ng/L and 55-159 ng/L, respectively) were encountered in final effluent samples from sewage treatment plants (STPs) discharging into the Tamar and Plym Estuaries (UK), with lower concentrations of Celestolide (ADBI) (4-13 ng/L), Phantolide (AHMI) (6-9 ng/L), musk xylene (MX) (4-7 ng/L) and musk ketone (MK) (18-30 ng/L). Rapid dilution from the outfalls is demonstrated with resulting concentrations of HHCB spanning from 5 to 30 ng/L and those for AHTN from 3 to 15 ng/L. The other musks were generally not detected in the estuarine and coastal waters. The suspended particulate matter (SPM) and sedimentary profiles and compositions (HHCB:AHTN ratios) generally reflect the distribution in the water column with highest concentrations adjacent to sewage outfalls. - Synthetic musks were determined in coastal environmental compartments along an estuarine transect indicating their ubiquitous occurrence in transitional waters.

Inputs and distributions of synthetic musk fragrances in an estuarine and coastal environment; a case study

Energy Technology Data Exchange (ETDEWEB)

Sumner, Nicola R. [School of Earth, Ocean and Environmental Science, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Plymouth Marine Laboratory, Prospect Place, The Hoe, Plymouth PL1 3DH (United Kingdom); Guitart, Carlos, E-mail: guitart.carlos@gmail.co [Plymouth Marine Laboratory, Prospect Place, The Hoe, Plymouth PL1 3DH (United Kingdom); Fuentes, Gustavo [Instituto Universitario de Tecnologia del Mar (IUTEMAR), Fundacion La Salle de Ciencias Naturales, Margarita Island (Venezuela, Bolivarian Republic of); Readman, James W. [Plymouth Marine Laboratory, Prospect Place, The Hoe, Plymouth PL1 3DH (United Kingdom)

2010-01-15

Synthetic musks are ubiquitous contaminants in the environment. Compartmental distributions (dissolved, suspended particle associated and sedimentary) of the compounds throughout an axial estuarine transect and in coastal waters are reported. High concentrations of Galaxolide (HHCB) and Tonalide (AHTN) (987-2098 ng/L and 55-159 ng/L, respectively) were encountered in final effluent samples from sewage treatment plants (STPs) discharging into the Tamar and Plym Estuaries (UK), with lower concentrations of Celestolide (ADBI) (4-13 ng/L), Phantolide (AHMI) (6-9 ng/L), musk xylene (MX) (4-7 ng/L) and musk ketone (MK) (18-30 ng/L). Rapid dilution from the outfalls is demonstrated with resulting concentrations of HHCB spanning from 5 to 30 ng/L and those for AHTN from 3 to 15 ng/L. The other musks were generally not detected in the estuarine and coastal waters. The suspended particulate matter (SPM) and sedimentary profiles and compositions (HHCB:AHTN ratios) generally reflect the distribution in the water column with highest concentrations adjacent to sewage outfalls. - Synthetic musks were determined in coastal environmental compartments along an estuarine transect indicating their ubiquitous occurrence in transitional waters.

Robustness to non-normality of various tests for the one-sample location problem

Directory of Open Access Journals (Sweden)

Michelle K. McDougall

2004-01-01

Full Text Available This paper studies the effect of the normal distribution assumption on the power and size of the sign test, Wilcoxon's signed rank test and the t-test when used in one-sample location problems. Power functions for these tests under various skewness and kurtosis conditions are produced for several sample sizes from simulated data using the g-and-k distribution of MacGillivray and Cannon [5].

Evaluation of the role of location and distance in recruitment in respondent-driven sampling

Directory of Open Access Journals (Sweden)

Hayes Richard J

2011-10-01

Full Text Available Abstract Background Respondent-driven sampling(RDS is an increasingly widely used variant of a link tracing design for recruiting hidden populations. The role of the spatial distribution of the target population has not been robustly examined for RDS. We examine patterns of recruitment by location, and how they may have biased an RDS study findings. Methods Total-population data were available on a range of characteristics on a population of 2402 male household-heads from an open cohort of 25 villages in rural Uganda. The locations of households were known a-priori. An RDS survey was carried out in this population, employing current RDS methods of sampling and statistical inference. Results There was little heterogeneity in the population by location. Data suggested more distant contacts were less likely to be reported, and therefore recruited, but if reported more distant contacts were as likely as closer contacts to be recruited. There was no evidence that closer proximity to a village meeting place was associated with probability of being recruited, however it was associated with a higher probability of recruiting a larger number of recruits. People living closer to an interview site were more likely to be recruited. Conclusions Household location affected the overall probability of recruitment, and the probability of recruitment by a specific recruiter. Patterns of recruitment do not appear to have greatly biased estimates in this study. The observed patterns could result in bias in more geographically heterogeneous populations. Care is required in RDS studies when choosing the network size question and interview site location(s.

An empirical comparison of respondent-driven sampling, time location sampling, and snowball sampling for behavioral surveillance in men who have sex with men, Fortaleza, Brazil.

Science.gov (United States)

Kendall, Carl; Kerr, Ligia R F S; Gondim, Rogerio C; Werneck, Guilherme L; Macena, Raimunda Hermelinda Maia; Pontes, Marta Kerr; Johnston, Lisa G; Sabin, Keith; McFarland, Willi

2008-07-01

Obtaining samples of populations at risk for HIV challenges surveillance, prevention planning, and evaluation. Methods used include snowball sampling, time location sampling (TLS), and respondent-driven sampling (RDS). Few studies have made side-by-side comparisons to assess their relative advantages. We compared snowball, TLS, and RDS surveys of men who have sex with men (MSM) in Forteleza, Brazil, with a focus on the socio-economic status (SES) and risk behaviors of the samples to each other, to known AIDS cases and to the general population. RDS produced a sample with wider inclusion of lower SES than snowball sampling or TLS-a finding of health significance given the majority of AIDS cases reported among MSM in the state were low SES. RDS also achieved the sample size faster and at lower cost. For reasons of inclusion and cost-efficiency, RDS is the sampling methodology of choice for HIV surveillance of MSM in Fortaleza.

Identification of Clusters of Foot Pain Location in a Community Sample.

Science.gov (United States)

Gill, Tiffany K; Menz, Hylton B; Landorf, Karl B; Arnold, John B; Taylor, Anne W; Hill, Catherine L

2017-12-01

To identify foot pain clusters according to pain location in a community-based sample of the general population. This study analyzed data from the North West Adelaide Health Study. Data were obtained between 2004 and 2006, using computer-assisted telephone interviewing, clinical assessment, and self-completed questionnaire. The location of foot pain was assessed using a diagram during the clinical assessment. Hierarchical cluster analysis was undertaken to identify foot pain location clusters, which were then compared in relation to demographics, comorbidities, and podiatry services utilization. There were 558 participants with foot pain (mean age 54.4 years, 57.5% female). Five clusters were identified: 1 with predominantly arch and ball pain (26.8%), 1 with rearfoot pain (20.9%), 1 with heel pain (13.3%), and 2 with predominantly forefoot, toe, and nail pain (28.3% and 10.7%). Each cluster was distinct in age, sex, and comorbidity profile. Of the two clusters with predominantly forefoot, toe, and nail pain, one of them had a higher proportion of men and those classified as obese, had diabetes mellitus, and used podiatry services (30%), while the other was comprised of a higher proportion of women who were overweight and reported less use of podiatry services (17.5%). Five clusters of foot pain according to pain location were identified, all with distinct age, sex, and comorbidity profiles. These findings may assist in the identification of individuals at risk for developing foot pain and in the development of targeted preventive strategies and treatments. © 2017, American College of Rheumatology.

Hydrochemical modelling of water quality in terms of emerging micropollutants in Mpumalanga, Gauteng and North West Provinces

Science.gov (United States)

Wanda, Elijah M. M.; Mamba, Bhekie B.; Msagati, Titus A. M.

2017-08-01

Emerging micropollutants (EMPs) are ubiquitous in aquatic systems and are associated with a wide range of eco-toxicological effects worldwide. There remains a lack of scientific understanding of the major underlying hydrochemical factors behind variations in concentration heterogeneities of EMPs in time and space. This study was therefore conducted to determine major hydrochemical processes controlling water quality and the occurrence of EMPs mainly, carbamazepine (CBZ), tonalide (AHTN), galaxolide (HHCB), caffeine (CAF), technical 4-nonylphenol (NP) and bisphenol A (BPA) in water from Mpumalanga, Gauteng and North West Provinces in South Africa. Grab water samples were collected bi-monthly between June 2014 and April 2016 from 44 water sources using standard sampling procedures. BPA, NP, CAF, HHCB, AHTN, CBZ were extracted, cleaned and enriched using autotrace-SPE at neutral pH and analyzed using GC × GC-TOFMS. Kruskal Wallis-test was used to test for temporal variations in occurrence of the analytes. The Geochemist's Workbench® Release 11 software, Surfer Golden Graphics for surface mapping, PHREEQC software and bivariate ion plots were used determine the major hydrogeochemical processes. The mean concentrations of EMPs varied from 3.48 μg/L for CAF to 421.53 μg/L for HHCB. Although the Kruskal Wallis test revealed no any statistically significant temporal variations in concentrations of the analytes in water samples at 95% confidence level, their occurrence and distribution vary spatially with BPA being the most widely distributed EMP and was present in 62% of the sampled sites. Municipal waste water inputs, agricultural pollution, ion-exchange reactions, carbonate and silicate weathering were the major processes controlling water quality in the study area. This study may assist water resource managers to ably address and manage water pollution resulting from a number of natural and anthropogenic hydrochemical processes in the study area.

Seasonal rationalization of river water quality sampling locations: a comparative study of the modified Sanders and multivariate statistical approaches.

Science.gov (United States)

Varekar, Vikas; Karmakar, Subhankar; Jha, Ramakar

2016-02-01

The design of surface water quality sampling location is a crucial decision-making process for rationalization of monitoring network. The quantity, quality, and types of available dataset (watershed characteristics and water quality data) may affect the selection of appropriate design methodology. The modified Sanders approach and multivariate statistical techniques [particularly factor analysis (FA)/principal component analysis (PCA)] are well-accepted and widely used techniques for design of sampling locations. However, their performance may vary significantly with quantity, quality, and types of available dataset. In this paper, an attempt has been made to evaluate performance of these techniques by accounting the effect of seasonal variation, under a situation of limited water quality data but extensive watershed characteristics information, as continuous and consistent river water quality data is usually difficult to obtain, whereas watershed information may be made available through application of geospatial techniques. A case study of Kali River, Western Uttar Pradesh, India, is selected for the analysis. The monitoring was carried out at 16 sampling locations. The discrete and diffuse pollution loads at different sampling sites were estimated and accounted using modified Sanders approach, whereas the monitored physical and chemical water quality parameters were utilized as inputs for FA/PCA. The designed optimum number of sampling locations for monsoon and non-monsoon seasons by modified Sanders approach are eight and seven while that for FA/PCA are eleven and nine, respectively. Less variation in the number and locations of designed sampling sites were obtained by both techniques, which shows stability of results. A geospatial analysis has also been carried out to check the significance of designed sampling location with respect to river basin characteristics and land use of the study area. Both methods are equally efficient; however, modified Sanders

Results of Macroinvertebrate Sampling Conducted at 33 SRS Stream Locations, July--August 1993

Energy Technology Data Exchange (ETDEWEB)

Specht, W.L.

1994-12-01

In order to assess the health of the macroinvertebrate communities of SRS streams, the macroinvertebrate communities at 30 stream locations on SRS were sampled during the summer of 1993, using Hester-Dendy multiplate samplers. In addition, three off-site locations in the Upper Three Runs drainage were sampled in order to assess the potential for impact from off-site activities. In interpreting the data, it is important to recognize that these data were from a single set of collections. Macroinvertebrate communities often undergo considerable temporal variation, and are also greatly influenced by such factors as water depth, water velocity, and available habitat. These stations were selected with the intent of developing an on-going sampling program at a smaller number of stations, with the selection of the stations to be based largely upon the results of this preliminary sampling program. When stations within a given stream showed similar results, fewer stations would be sampled in the future. Similarly, if a stream appeared to be perturbed, additional stations or chemical analyses might be added so that the source of the perturbation could be identified. In general, unperturbed streams will contain more taxa than perturbed streams, and the distribution of taxa among orders or families will differ. Some groups of macroinvertebrates, such as Ephemeroptera (mayflies), Plecoptera (stoneflies) and Trichoptera (caddisflies), which are collectively called EPT taxa, are considered to be relatively sensitive to most kinds of stream perturbation; therefore a reduced number of EPT taxa generally indicates that the stream has been subject to chemical or physical stressors. In coastal plain streams, EPT taxa are generally less dominant than in streams with rocky substrates, while Chironomidae (midges) are more abundant. (Abstract Truncated)

UV-filters and musk fragrances in seafood commercialized in Europe Union: Occurrence, risk and exposure assessment.

Science.gov (United States)

Cunha, S C; Trabalón, L; Jacobs, S; Castro, M; Fernandez-Tejedor, M; Granby, K; Verbeke, W; Kwadijk, C; Ferrari, F; Robbens, J; Sioen, I; Pocurull, E; Marques, A; Fernandes, J O; Domingo, J L

2018-02-01

In the framework of the FP7 ECsafeSeafood project, 62 seafood samples commercialized in Europe Union from several representative species - mackerel, tuna, salmon, seabream, cod, monkfish, crab, shrimp, octopus, perch and plaice - were analysed for residues of 21 personal care products (PCPs), including 11 UV-filters (UV-Fs) and 10 musk fragrances (musks). PCPs analysis were performed by Quick, Easy, Cheap, Effective Rugged, Safe (QuEChERS), combined with liquid-liquid extraction (LLE) or dispersive solid-phase extraction (dSPE), followed by gas chromatography-tandem mass spectrometry (GC-MS/MS). The results showed the presence in a wide range of samples of nine out of eleven UV-Fs compounds analysed, namely 2-ethylhexyl salicylate (EHS), 2-ethylhexyl,4-methoxycinnamate (EHMC), 4-methylbenzylidenecamphor (4-MBC), benzophenone-1 (BP1), benzophenone-3 (BP3), isoamyl-4-methoxycinnamate (IMC), 2,2'-dihydroxy-4,4'-dimethoxybenzophenone (DHMB), homosalate (HS), and octocrylene (OC), whereas galaxolide (HHCB), galaxolide lactone (HHCB-lactone), and tonalide (AHTN) were the most found musks. The potential risks to human health associated with the exposure to eight of the more prevalent PCPs - EHS, EHMC, 4-MBC, BP1, BP3, IMC, HHCB, and AHTN - through seafood consumption were assessed for consumers from five European countries (Belgium, Ireland, Italy, Portugal and Spain). Results showed that the human exposure to UV-Fs and musks estimated from the concentration values found in seafood and the daily consumption of concerned seafood species, were far below toxicological reference values. Copyright © 2017 Elsevier Inc. All rights reserved.

Water Quality Sampling Locations Along the Shoreline of the Columbia River, Hanford Site, Washington

Energy Technology Data Exchange (ETDEWEB)

Peterson, Robert E.; Patton, Gregory W.

2009-12-14

As environmental monitoring evolved on the Hanford Site, several different conventions were used to name or describe location information for various sampling sites along the Hanford Reach of the Columbia River. These methods range from handwritten descriptions in field notebooks to the use of modern electronic surveying equipment, such as Global Positioning System receivers. These diverse methods resulted in inconsistent archiving of analytical results in various electronic databases and published reports because of multiple names being used for the same site and inaccurate position data. This document provides listings of sampling sites that are associated with groundwater and river water sampling. The report identifies names and locations for sites associated with sampling: (a) near-river groundwater using aquifer sampling tubes; (b) riverbank springs and springs areas; (c) pore water collected from riverbed sediment; and (d) Columbia River water. Included in the listings are historical names used for a particular site and the best available geographic coordinates for the site, as of 2009. In an effort to create more consistency in the descriptive names used for water quality sampling sites, a naming convention is proposed in this document. The convention assumes that a unique identifier is assigned to each site that is monitored and that this identifier serves electronic database management requirements. The descriptive name is assigned for the convenience of the subsequent data user. As the historical database is used more intensively, this document may be revised as a consequence of discovering potential errors and also because of a need to gain consensus on the proposed naming convention for some water quality monitoring sites.

40 CFR 141.703 - Sampling locations.

Science.gov (United States)

2010-07-01

... samples prior to the point of filter backwash water addition. (d) Bank filtration. (1) Systems that... applicable, must collect source water samples in the surface water prior to bank filtration. (2) Systems that use bank filtration as pretreatment to a filtration plant must collect source water samples from the...

Location tests for biomarker studies: a comparison using simulations for the two-sample case.

Science.gov (United States)

Scheinhardt, M O; Ziegler, A

2013-01-01

Gene, protein, or metabolite expression levels are often non-normally distributed, heavy tailed and contain outliers. Standard statistical approaches may fail as location tests in this situation. In three Monte-Carlo simulation studies, we aimed at comparing the type I error levels and empirical power of standard location tests and three adaptive tests [O'Gorman, Can J Stat 1997; 25: 269 -279; Keselman et al., Brit J Math Stat Psychol 2007; 60: 267- 293; Szymczak et al., Stat Med 2013; 32: 524 - 537] for a wide range of distributions. We simulated two-sample scenarios using the g-and-k-distribution family to systematically vary tail length and skewness with identical and varying variability between groups. All tests kept the type I error level when groups did not vary in their variability. The standard non-parametric U-test performed well in all simulated scenarios. It was outperformed by the two non-parametric adaptive methods in case of heavy tails or large skewness. Most tests did not keep the type I error level for skewed data in the case of heterogeneous variances. The standard U-test was a powerful and robust location test for most of the simulated scenarios except for very heavy tailed or heavy skewed data, and it is thus to be recommended except for these cases. The non-parametric adaptive tests were powerful for both normal and non-normal distributions under sample variance homogeneity. But when sample variances differed, they did not keep the type I error level. The parametric adaptive test lacks power for skewed and heavy tailed distributions.

Assessment of the LV-C2 Stack Sampling Probe Location for Compliance with ANSI/HPS N13.1-1999

Energy Technology Data Exchange (ETDEWEB)

Glissmeyer, John A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Antonio, Ernest J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Flaherty, Julia E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-09-01

This document reports on a series of tests conducted to assess the proposed air sampling location for the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste (LAW) C2V (LV-C2) exhaust stack with respect to the applicable criteria regarding the placement of an air sampling probe. Federal regulations require that a sampling probe be located in the exhaust stack according to the criteria established by the American National Standards Institute/Health Physics Society (ANSI/HPS) N13.1-1999, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stack and Ducts of Nuclear Facilities. These criteria address the capability of the sampling probe to extract a sample that represents the effluent stream. The tests were conducted on the LV-C2 scale model system. Based on the scale model tests, the location proposed for the air sampling probe in the scale model stack meets the requirements of the ANSI/HPS N13.1-1999 standard for velocity uniformity, flow angle, gas tracer and particle tracer uniformity. Additional velocity uniformity and flow angle tests on the actual stack will be necessary during cold startup to confirm the validity of the scale model results in representing the actual stack.

Estimation of uranium in drinking water samples collected from different locations across Tarapur, India

International Nuclear Information System (INIS)

Dusane, C.B.; Maity, Sukanta; Sahu, S.K.; Pandit, G.G.

2015-01-01

In this study, drinking water samples were collected from different locations across Tarapur, India for screening uranium contents. Uranium concentrations were determined by differential pulse adsorptive stripping voltammetry (DPASV). Uranium concentration in water samples varied in a wide range from 0.6-7.9 μg L -1 . Results were compared with the international water quality guidelines World Health Organization (WHO, 2011) and were found within the permissible limit. Results were also compared with the safe limit values for drinking water recommended by national organization like Atomic Energy Regulatory Board (AERB). (author)

MUSIC ALGORITHM FOR LOCATING POINT-LIKE SCATTERERS CONTAINED IN A SAMPLE ON FLAT SUBSTRATE

Institute of Scientific and Technical Information of China (English)

Dong Heping; Ma Fuming; Zhang Deyue

2012-01-01

In this paper,we consider a MUSIC algorithm for locating point-like scatterers contained in a sample on flat substrate.Based on an asymptotic expansion of the scattering amplitude proposed by Ammari et al.,the reconstruction problem can be reduced to a calculation of Green function corresponding to the background medium.In addition,we use an explicit formulation of Green function in the MUSIC algorithm to simplify the calculation when the cross-section of sample is a half-disc.Numerical experiments are included to demonstrate the feasibility of this method.

1999 Baseline Sampling and Analysis Sampling Locations, Geographic NAD83, LOSCO (2004) [BSA_1999_sample_locations_LOSCO_2004

Data.gov (United States)

Louisiana Geographic Information Center — The monitor point data set was produced as a part of the Baseline Sampling and Analysis program coordinated by the Louisiana Oil Spill Coordinator's Office. This...

1997 Baseline Sampling and Analysis Sample Locations, Geographic NAD83, LOSCO (2004) [BSA_1997_sample_locations_LOSCO_2004

Data.gov (United States)

Louisiana Geographic Information Center — The monitor point data set was produced as a part of the Baseline Sampling and Analysis (BSA) program coordinated by the Louisiana Oil Spill Coordinator's Office....

1998 Baseline Sampling and Analysis Sampling Locations, Geographic NAD83, LOSCO (2004) [BSA_1998_sample_locations_LOSCO_2004

Data.gov (United States)

Louisiana Geographic Information Center — The monitor point data set was produced as a part of the Baseline Sampling and Analysis program coordinated by the Louisiana Oil Spill Coordinator's Office. This...

Use of space-filling curves to select sample locations in natural resource monitoring studies

Science.gov (United States)

Andrew Lister; Charles T. Scott

2009-01-01

The establishment of several large area monitoring networks over the past few decades has led to increased research into ways to spatially balance sample locations across the landscape. Many of these methods are well documented and have been used in the past with great success. In this paper, we present a method using geographic information systems (GIS) and fractals...

Estrogenic and esterase-inhibiting potency in rainwater in relation to pesticide concentrations, sampling season and location

Energy Technology Data Exchange (ETDEWEB)

Hamers, T.; Brink, P.J. van den; Mos, L.; Linden, S.C. van der; Legler, J.; Koeman, J.H.; Murk, A.J

2003-05-01

Estrogenic potency of rainwater correlated well with organochlorine concentrations, but could not be attributed to specific pesticides. - In a year-round monitoring program (1998), pesticide composition and toxic potency of the mix of pollutants present in rainwater were measured. The goal of the study was to relate atmospheric deposition of toxic potency and pesticide composition to each other and to sampling period and local agricultural activity. Rainwater was collected in 26 consecutive periods of 14 days in a background location (BACK) and in two locations representative for different agricultural practices, i.e. intensive greenhouse horticulture (HORT) and flower bulb culture (BULB). Samples were chemically analyzed for carbamate (CARB), organophosphate (OP) and organochlorine (OC) pesticides and metabolites. Esterase inhibiting potency of rainwater extracts was measured in a specially developed bio-assay with honeybee esterases and was expressed as an equivalent concentration of the model inhibitor dichlorvos. Estrogenic potency of the extracts was measured in the ER-CALUX reporter gene assay and was expressed as an equivalent concentration of estradiol. Multivariate principal component analysis (PCA) techniques proved to be valuable tools to analyze the numerous pesticide concentrations in relation to toxic potency, sampling location, and sampling season. Pesticide composition in rainwater depended much more on sampling season than on sampling location, but differences between SPRING and SUMMER were mainly attributed to local differences in agricultural practice. On average, the esterase inhibiting potency exceeded the maximum permissible concentration set for dichlorvos in The Netherlands, and was significantly higher in HORT than in BACK and BULB. Esterase inhibition correlated significantly with OP and CARB concentrations, as expected given the working mechanism of these insecticides. The estrogenic potency incidentally exceeded NOEC levels reported for

Estrogenic and esterase-inhibiting potency in rainwater in relation to pesticide concentrations, sampling season and location

International Nuclear Information System (INIS)

Hamers, T.; Brink, P.J. van den; Mos, L.; Linden, S.C. van der; Legler, J.; Koeman, J.H.; Murk, A.J.

2003-01-01

Estrogenic potency of rainwater correlated well with organochlorine concentrations, but could not be attributed to specific pesticides. - In a year-round monitoring program (1998), pesticide composition and toxic potency of the mix of pollutants present in rainwater were measured. The goal of the study was to relate atmospheric deposition of toxic potency and pesticide composition to each other and to sampling period and local agricultural activity. Rainwater was collected in 26 consecutive periods of 14 days in a background location (BACK) and in two locations representative for different agricultural practices, i.e. intensive greenhouse horticulture (HORT) and flower bulb culture (BULB). Samples were chemically analyzed for carbamate (CARB), organophosphate (OP) and organochlorine (OC) pesticides and metabolites. Esterase inhibiting potency of rainwater extracts was measured in a specially developed bio-assay with honeybee esterases and was expressed as an equivalent concentration of the model inhibitor dichlorvos. Estrogenic potency of the extracts was measured in the ER-CALUX reporter gene assay and was expressed as an equivalent concentration of estradiol. Multivariate principal component analysis (PCA) techniques proved to be valuable tools to analyze the numerous pesticide concentrations in relation to toxic potency, sampling location, and sampling season. Pesticide composition in rainwater depended much more on sampling season than on sampling location, but differences between SPRING and SUMMER were mainly attributed to local differences in agricultural practice. On average, the esterase inhibiting potency exceeded the maximum permissible concentration set for dichlorvos in The Netherlands, and was significantly higher in HORT than in BACK and BULB. Esterase inhibition correlated significantly with OP and CARB concentrations, as expected given the working mechanism of these insecticides. The estrogenic potency incidentally exceeded NOEC levels reported for

Toxicity assessment of simulated urban runoff containing polycyclic musks and cadmium in Carassius auratus using oxidative stress biomarkers

International Nuclear Information System (INIS)

Chen Fang; Gao Jie; Zhou Qixing

2012-01-01

The objective of this study was to assess potential toxic effects of simulated urban runoff on Carassius auratus using oxidative stress biomarkers. The activity of antioxidant enzymes including superoxide dismutase (SOD), peroxidase (POD) and catalase (CAT), and the content of malondialdehyde (MDA) in the liver of C. auratus were analyzed after a 7-, 14- and 21-day exposure to simulated urban runoff containing galaxolide (HHCB) and cadmium (Cd). The results showed that the activity of antioxidant enzymes and the content of MDA increased significantly exposed to the simulated urban runoff containing HHCB alone or mixture of HHCB and Cd. The activity of the investigated enzymes and the content of MDA then returned to the blank level over a longer period of exposure. The oxidative stress could be obviously caused in the liver of C. auratus under the experimental conditions. This could provide useful information for toxic risk assessment of urban runoff. - Highlights: ► We assessed potential toxicity of urban runoff containing HHCB and Cd. ► Exposure of simulated urban runoff can caused oxidative stress in C. auratus liver. ► SOD and CAT are more sensitive than POD and more suitable for indicating the toxicity of urban runoff. ► The present study using oxidative stress biomarkers could provide useful information for toxic risk assessment of urban runoff. - Simulated urban runoff containing HHCB and Cd could cause oxidative stress on the liver of Carassius auratus, which could provide useful information for toxic risk assessment of urban runoff.

Fixed-location hydroacoustic monitoring designs for estimating fish passage using stratified random and systematic sampling

International Nuclear Information System (INIS)

Skalski, J.R.; Hoffman, A.; Ransom, B.H.; Steig, T.W.

1993-01-01

Five alternate sampling designs are compared using 15 d of 24-h continuous hydroacoustic data to identify the most favorable approach to fixed-location hydroacoustic monitoring of salmonid outmigrants. Four alternative aproaches to systematic sampling are compared among themselves and with stratified random sampling (STRS). Stratifying systematic sampling (STSYS) on a daily basis is found to reduce sampling error in multiday monitoring studies. Although sampling precision was predictable with varying levels of effort in STRS, neither magnitude nor direction of change in precision was predictable when effort was varied in systematic sampling (SYS). Furthermore, modifying systematic sampling to include replicated (e.g., nested) sampling (RSYS) is further shown to provide unbiased point and variance estimates as does STRS. Numerous short sampling intervals (e.g., 12 samples of 1-min duration per hour) must be monitored hourly using RSYS to provide efficient, unbiased point and interval estimates. For equal levels of effort, STRS outperformed all variations of SYS examined. Parametric approaches to confidence interval estimates are found to be superior to nonparametric interval estimates (i.e., bootstrap and jackknife) in estimating total fish passage. 10 refs., 1 fig., 8 tabs

Assessment of the National Research Universal Reactor Proposed New Stack Sampling Probe Location for Compliance with ANSI/HPS N13.1-1999

Energy Technology Data Exchange (ETDEWEB)

Glissmeyer, John A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Antonio, Ernest J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Flaherty, Julia E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-02-29

This document reports on a series of tests conducted to assess the proposed air sampling location for the National Research Universal reactor (NRU) complex exhaust stack, located in Chalk River, Ontario, Canada, with respect to the applicable criteria regarding the placement of an air sampling probe. Due to the age of the equipment in the existing monitoring system, and the increasing difficulty in acquiring replacement parts to maintain this equipment, a more up-to-date system is planned to replace the current effluent monitoring system, and a new monitoring location has been proposed. The new sampling probe should be located within the exhaust stack according to the criteria established by the American National Standards Institute/Health Physics Society (ANSI/HPS) N13.1-1999, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stack and Ducts of Nuclear Facilities. These criteria address the capability of the sampling probe to extract a sample that represents the effluent stream. The internal Pacific Northwest National Laboratory (PNNL) project for this task was 65167, Atomic Energy Canada Ltd. Chalk River Effluent Duct Flow Qualification. The testing described in this document was guided by the Test Plan: Testing of the NRU Stack Air Sampling Position (TP-STMON-032).

Robustness to non-normality of common tests for the many-sample location problem

Directory of Open Access Journals (Sweden)

Azmeri Khan

2003-01-01

Full Text Available This paper studies the effect of deviating from the normal distribution assumption when considering the power of two many-sample location test procedures: ANOVA (parametric and Kruskal-Wallis (non-parametric. Power functions for these tests under various conditions are produced using simulation, where the simulated data are produced using MacGillivray and Cannon's [10] recently suggested g-and-k distribution. This distribution can provide data with selected amounts of skewness and kurtosis by varying two nearly independent parameters.

Location and multi-depot vehicle routing for emergency vehicles using tour coverage and random sampling

Directory of Open Access Journals (Sweden)

Alireza Goli

2015-09-01

Full Text Available Distribution and optimum allocation of emergency resources are the most important tasks, which need to be accomplished during crisis. When a natural disaster such as earthquake, flood, etc. takes place, it is necessary to deliver rescue efforts as quickly as possible. Therefore, it is important to find optimum location and distribution of emergency relief resources. When a natural disaster occurs, it is not possible to reach some damaged areas. In this paper, location and multi-depot vehicle routing for emergency vehicles using tour coverage and random sampling is investigated. In this study, there is no need to visit all the places and some demand points receive their needs from the nearest possible location. The proposed study is implemented for some randomly generated numbers in different sizes. The preliminary results indicate that the proposed method was capable of reaching desirable solutions in reasonable amount of time.

Synthetic Musk Fragrances in a Conventional Drinking Water Treatment Plant with Lime Softening

OpenAIRE

Wombacher, William D.; Hornbuckle, Keri C.

2009-01-01

Synthetic musk fragrances are common personal care product additives and wastewater contaminants that are routinely detected in the environment. This study examines the presence eight synthetic musk fragrances (AHTN, HHCB, ATII, ADBI, AHMI, musk xylene, and musk ketone) in source water and the removal of these compounds as they flow through a Midwestern conventional drinking water plant with lime softening. The compounds were measured in water, waste sludge, and air throughout the plant. HHCB...

[Strategies for biobank networks. Classification of different approaches for locating samples and an outlook on the future within the BBMRI-ERIC].

Science.gov (United States)

Lablans, Martin; Kadioglu, Dennis; Mate, Sebastian; Leb, Ines; Prokosch, Hans-Ulrich; Ückert, Frank

2016-03-01

Medical research projects often require more biological material than can be supplied by a single biobank. For this reason, a multitude of strategies support locating potential research partners with matching material without requiring centralization of sample storage. Classification of different strategies for biobank networks, in particular for locating suitable samples. Description of an IT infrastructure combining these strategies. Existing strategies can be classified according to three criteria: (a) granularity of sample data: coarse bank-level data (catalogue) vs. fine-granular sample-level data, (b) location of sample data: central (central search service) vs. decentral storage (federated search services), and (c) level of automation: automatic (query-based, federated search service) vs. semi-automatic (inquiry-based, decentral search). All mentioned search services require data integration. Metadata help to overcome semantic heterogeneity. The "Common Service IT" in BBMRI-ERIC (Biobanking and BioMolecular Resources Research Infrastructure) unites a catalogue, the decentral search and metadata in an integrated platform. As a result, researchers receive versatile tools to search suitable biomaterial, while biobanks retain a high degree of data sovereignty. Despite their differences, the presented strategies for biobank networks do not rule each other out but can complement and even benefit from each other.

Determinants of Exposure to Fragranced Product Chemical Mixtures in a Sample of Twins

Directory of Open Access Journals (Sweden)

Matthew O. Gribble

2015-01-01

Full Text Available Fragranced product chemical mixtures may be relevant for environmental health, but little is known about exposure. We analyzed results from an olfactory challenge with the synthetic musk fragrance 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethyl-cyclopento-γ-2-benzopyran (HHCB, and a questionnaire about attitudes toward chemical safety and use of fragranced products, in a sample of 140 white and 17 black twin pairs attending a festival in Ohio. Data for each product were analyzed using robust ordered logistic regressions with random intercepts for “twin pair” and “sharing address with twin”, and fixed effects for sex, age, education, and “ever being bothered by fragrances”. Due to the small number of black participants, models were restricted to white participants except when examining racial differences. Overall patterns of association were summarized across product-types through random-effects meta-analysis. Principal components analysis was used to summarize clustering of product use. The dominant axis of variability in fragranced product use was “more vs. less”, followed by a distinction between household cleaning products and personal care products. Overall, males used fragranced products less frequently than females (adjusted proportionate odds ratio 0.55, 95% confidence interval 0.33, 0.93. This disparity was driven by personal care products (0.42, 95% CI: 0.19, 0.96, rather than household cleaning products (0.79, 95% CI: 0.49, 1.25 and was particularly evident for body lotion (0.12, 95% CI: 0.05, 0.27. Overall usage differed by age (0.64, 95% CI: 0.43, 0.95 but only hand soap and shampoo products differed significantly. “Ever being bothered by fragrance” had no overall association (0.92, 95% CI: 0.65, 1.30 but was associated with laundry detergent use (0.46, 95% CI: 0.23, 0.93. Similarly, black vs. white differences on average were not significant (1.34, 95% CI: 0.55, 3.28 but there were apparent differences in use of

Determinants of Exposure to Fragranced Product Chemical Mixtures in a Sample of Twins

Science.gov (United States)

Gribble, Matthew O.; Bandeen-Roche, Karen; Fox, Mary A.

2015-01-01

Fragranced product chemical mixtures may be relevant for environmental health, but little is known about exposure. We analyzed results from an olfactory challenge with the synthetic musk fragrance 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethyl-cyclopento-γ-2-benzopyran (HHCB), and a questionnaire about attitudes toward chemical safety and use of fragranced products, in a sample of 140 white and 17 black twin pairs attending a festival in Ohio. Data for each product were analyzed using robust ordered logistic regressions with random intercepts for “twin pair” and “sharing address with twin”, and fixed effects for sex, age, education, and “ever being bothered by fragrances”. Due to the small number of black participants, models were restricted to white participants except when examining racial differences. Overall patterns of association were summarized across product-types through random-effects meta-analysis. Principal components analysis was used to summarize clustering of product use. The dominant axis of variability in fragranced product use was “more vs. less”, followed by a distinction between household cleaning products and personal care products. Overall, males used fragranced products less frequently than females (adjusted proportionate odds ratio 0.55, 95% confidence interval 0.33, 0.93). This disparity was driven by personal care products (0.42, 95% CI: 0.19, 0.96), rather than household cleaning products (0.79, 95% CI: 0.49, 1.25) and was particularly evident for body lotion (0.12, 95% CI: 0.05, 0.27). Overall usage differed by age (0.64, 95% CI: 0.43, 0.95) but only hand soap and shampoo products differed significantly. “Ever being bothered by fragrance” had no overall association (0.92, 95% CI: 0.65, 1.30) but was associated with laundry detergent use (0.46, 95% CI: 0.23, 0.93). Similarly, black vs. white differences on average were not significant (1.34, 95% CI: 0.55, 3.28) but there were apparent differences in use of shampoo (0

Assessment of the LV-S2 & LV-S3 Stack Sampling Probe Locations for Compliance with ANSI/HPS N13.1-1999

Energy Technology Data Exchange (ETDEWEB)

Glissmeyer, John A.; Antonio, Ernest J.; Flaherty, Julia E.; Amidan, Brett G.

2014-09-30

This document reports on a series of tests conducted to assess the proposed air sampling locations for the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Group 1-2A exhaust stacks with respect to the applicable criteria regarding the placement of an air sampling probe. The LV-C2, LV-S2, and LV-S3 exhaust stacks were tested together as a group (Test Group 1-2A). This report only covers the results of LV-S2 and LV-S3; LV-C2 will be reported on separately. Federal regulations1 require that a sampling probe be located in the exhaust stack according to the criteria established by the American National Standards Institute/Health Physics Society (ANSI/HPS) N13.1-1999, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stack and Ducts of Nuclear Facilities. 2 These criteria address the capability of the sampling probe to extract a sample that represents the effluent stream.

Development of failed fuel detection and location system in sodium-cooled large reactor. Sampling method of failed fuels under the slit

International Nuclear Information System (INIS)

Aizawa, Kousuke; Fujita, Kaoru; Kamide, Hideki; Kasahara, Naoto

2010-01-01

A conceptual design study of Japan Sodium-cooled Fast Reactor (JSFR) is in progress as an issue of the 'Fast Reactor Cycle Technology Development (FaCT)' project in Japan. JSFR adopts a Selector-Valve mechanism for the failed fuel detection and location (FFDL) system. The Selector-Valve FFDL system identifies failed fuel subassemblies by sampling sodium from each fuel subassembly outlet and detecting fission product. One of the JSFR design features is employing an upper internal structure (UIS) with a radial slit, in which an arm of fuel handling machine can move and access the fuel assemblies under the UIS. Thus, JSFR cannot place sampling nozzles right above the fuel subassemblies located under the slit. In this study, the sampling method for indentifying under-slit failed fuel subassemblies has been demonstrated by water experiments. (author)

Assessment of Heavy Metals in Water Samples of Certain Locations Situated Around Tumkur, Karnataka, India

Directory of Open Access Journals (Sweden)

C. Vijaya Bhaskar

2010-01-01

Full Text Available Surface water and groundwater samples of certain locations namely Kallambella, Bugudanahalli, Maidala, Honnudike, Kunigal, Kadaba and Hebbur, situated around Tumkur were assessed in the month of September 2008 for pH, EC and heavy metals Cd, Cu, Fe, Hg, Mn, Zn and Ni. The pH vales of surface waters were in alkaline range of 7.8-8.2 and are well within safe limits for crop production. The pH of ground- water was in the range of 7.6-8.4. The conductivity was in the range of 0.20-0.68 mS/cm and 0.34-2.44 mS/cm for surface and groundwaters respectively. High EC value of Kallambella groundwater accounts for its salinity. All surface waters except Honnudike and Hebbur samples contain low concentrations of these metals and are ideal for irrigation. Though the samples from Honnudike, Kadaba and Hebbur have high iron concentration, only Honnudike and Hebbur samples have exceeded the limit of 5 mg/L required for irrigation. In groundwaters the concentrations of all these heavy metals except copper are also well in permissible limits and suitable for drinking. Cu, Fe, Ni and Zn were detected in all the samples and found in the range of 0.094-0.131, 0.958-12.537, 0.020-0.036 and 0.082-1.139 mg/L respectively in surface waters and these are in the range of 0.132-0.142, 0.125-1.014, 0.028-0.036 and 0.003-0.037 mg/L in ground- waters. The elements cadmium, mercury and manganese are absent in all the samples.

Control charts for location based on different sampling schemes

NARCIS (Netherlands)

Mehmood, R.; Riaz, M.; Does, R.J.M.M.

2013-01-01

Control charts are the most important statistical process control tool for monitoring variations in a process. A number of articles are available in the literature for the X̄ control chart based on simple random sampling, ranked set sampling, median-ranked set sampling (MRSS), extreme-ranked set

Occurrence of Emerging Micropollutants in Water Systems in Gauteng, Mpumalanga, and North West Provinces, South Africa.

Science.gov (United States)

Wanda, Elijah M M; Nyoni, Hlengilizwe; Mamba, Bhekie B; Msagati, Titus A M

2017-01-13

The ubiquitous occurrence of emerging micropollutants (EMPs) in water is an issue of growing environmental-health concern worldwide. However, there remains a paucity of data regarding their levels and occurrence in water. This study determined the occurrence of EMPs namely: carbamazepine (CBZ), galaxolide (HHCB), caffeine (CAF), tonalide (AHTN), 4-nonylphenol (NP), and bisphenol A (BPA) in water from Gauteng, Mpumalanga, and North West provinces, South Africa using comprehensive two-dimensional gas chromatography coupled to high resolution time-of-flight mass spectrometry (GCxGC-HRTOFMS). Kruskal-Wallis test and ANOVA were performed to determine temporal variations in occurrence of the EMPs. Principal component analysis (PCA) and Surfer Golden Graphics software for surface mapping were used to determine spatial variations in levels and occurrence of the EMPs. The mean levels ranged from 11.22 ± 18.8 ng/L for CAF to 158.49 ± 662 ng/L for HHCB. There was no evidence of statistically significant temporal variations in occurrence of EMPs in water. Nevertheless, their levels and occurrence vary spatially and are a function of two principal components (PCs, PC1 and PC2) which controlled 89.99% of the variance. BPA was the most widely distributed EMP, which was present in 62% of the water samples. The detected EMPs pose ecotoxicological risks in water samples, especially those from Mpumalanga province.

Gene Locater

DEFF Research Database (Denmark)

Anwar, Muhammad Zohaib; Sehar, Anoosha; Rehman, Inayat-Ur

2012-01-01

software's for calculating recombination frequency is mostly limited to the range and flexibility of this type of analysis. GENE LOCATER is a fully customizable program for calculating recombination frequency, written in JAVA. Through an easy-to-use interface, GENE LOCATOR allows users a high degree...... of flexibility in calculating genetic linkage and displaying linkage group. Among other features, this software enables user to identify linkage groups with output visualized graphically. The program calculates interference and coefficient of coincidence with elevated accuracy in sample datasets. AVAILABILITY...

ATP, IMP, and glycogen in cod muscle at onset and during development of rigor mortis depend on the sampling location

DEFF Research Database (Denmark)

Cappeln, Gertrud; Jessen, Flemming

2002-01-01

Variation in glycogen, ATP, and IMP contents within individual cod muscles were studied in ice stored fish during the progress of rigor mortis. Rigor index was determined before muscle samples for chemical analyzes were taken at 16 different positions on the fish. During development of rigor......, the contents of glycogen and ATP decreased differently in relation to rigor index depending on sampling location. Although fish were considered to be in strong rigor according to the rigor index method, parts of the muscle were not in rigor as high ATP concentrations were found in dorsal and tall muscle....

Reference Priors for the General Location-Scale Model

NARCIS (Netherlands)

Fernández, C.; Steel, M.F.J.

1997-01-01

The reference prior algorithm (Berger and Bernardo 1992) is applied to multivariate location-scale models with any regular sampling density, where we establish the irrelevance of the usual assumption of Normal sampling if our interest is in either the location or the scale. This result immediately

Evaluation of sampling inhalable PM10 particulate matter (≤ 10 μm) using co-located high volume samplers

International Nuclear Information System (INIS)

Rajoy, R R S; Dias, J W C; Rego, E C P; Netto, A D Pereira

2015-01-01

This paper presents the results of the determination of the concentrations of atmospheric particulate matter ≤ 10 μm (PM10), collected simultaneously by six PM10 high volume samplers from two different manufacturers installed in the same location. Fifteen samples of 24 h were obtained with each equipment at a selected urban area of Rio de Janeiro city. The concentration of PM10 ranged between 10.73 and 54.04 μg m −3 . The samplers were considered comparable to each other, as the adopted methodology presented good repeatability

Water born pollutants sampling using porous suction samples

International Nuclear Information System (INIS)

Baig, M.A.

1997-01-01

The common standard method of sampling water born pollutants in the vadoze zone is core sampling and it is followed by extraction of pore fluid. This method does not allow sampling at the same location next time and again later on. There is an alternative approach for sampling fluids (water born pollutants) from both saturated and unsaturated regions of vadose zone using porous suction samplers. There are three types of porous suction samplers, vacuum-operated, pressure-vacuum lysimeters, high pressure vacuum samples. The suction samples are operated in the range of 0-70 centi bars and usually consist of ceramic and polytetrafluorethylene (PTFE). The operation range of PTFE is higher than ceramic cups. These samplers are well suited for in situ and repeated sampling form the same location. This paper discusses the physical properties and operating condition of such samplers to the utilized under our environmental sampling. (author)

The effects of sampling location and turbulence on discharge estimates in short converging turbine intakes

Energy Technology Data Exchange (ETDEWEB)

Romero-Gomez, P.; Harding, S. F.; Richmond, M. C.

2017-01-01

Standards provide recommendations for best practices when installing current meters to measure fluid flow in closed conduits. A central guideline requires the velocity distribution to be regular and the flow steady. Because of the nature of the short converging intakes typical of low-head hydroturbines, these assumptions may be invalid if current meters are intended to be used to estimate discharge. Usual concerns are (1) the effects of the number of devices, (2) the sampling location and (3) the high turbulence caused by blockage from submersible traveling screens usually deployed for safe downstream fish passage. These three effects were examined in the present study by using 3D simulated flow fields in both steady-state and transient modes. In the process of describing an application at an existing hydroturbine intake at Ice Harbor Dam, the present work outlined the methods involved, which combined computational fluid dynamics, laboratory measurements in physical models of the hydroturbine, and current meter performance evaluations in experimental settings. The main conclusions in this specific application were that a steady-state flow field sufficed to determine the adequate number of meters and their location, and that both the transverse velocity and turbulence intensity had a small impact on estimate errors. However, while it may not be possible to extrapolate these findings to other field conditions and measuring devices, the study laid out a path to conduct similar assessments in other applications.

Locations of Sampling Stations for Water Quality Monitoring in Water Distribution Networks.

Science.gov (United States)

Rathi, Shweta; Gupta, Rajesh

2014-04-01

Water quality is required to be monitored in the water distribution networks (WDNs) at salient locations to assure the safe quality of water supplied to the consumers. Such monitoring stations (MSs) provide warning against any accidental contaminations. Various objectives like demand coverage, time for detection, volume of water contaminated before detection, extent of contamination, expected population affected prior to detection, detection likelihood and others, have been independently or jointly considered in determining optimal number and location of MSs in WDNs. "Demand coverage" defined as the percentage of network demand monitored by a particular monitoring station is a simple measure to locate MSs. Several methods based on formulation of coverage matrix using pre-specified coverage criteria and optimization have been suggested. Coverage criteria is defined as some minimum percentage of total flow received at the monitoring stations that passed through any upstream node included then as covered node of the monitoring station. Number of monitoring stations increases with the increase in the value of coverage criteria. Thus, the design of monitoring station becomes subjective. A simple methodology is proposed herein which priority wise iteratively selects MSs to achieve targeted demand coverage. The proposed methodology provided the same number and location of MSs for illustrative network as an optimization method did. Further, the proposed method is simple and avoids subjectivity that could arise from the consideration of coverage criteria. The application of methodology is also shown on a WDN of Dharampeth zone (Nagpur city WDN in Maharashtra, India) having 285 nodes and 367 pipes.

Seismic Measurement of the Locations of the Base of Convection Zone and Helium Ionization Zone for Stars in the Kepler Seismic LEGACY Sample

Energy Technology Data Exchange (ETDEWEB)

Verma, Kuldeep; Lund, Mikkel N.; Aguirre, Víctor Silva [Stellar Astrophysics Centre, Department of Physics and Astronomy, Aarhus University, Ny Munkegade 120, DK-8000 Aarhus C (Denmark); Raodeo, Keyuri; Mazumdar, Anwesh [Homi Bhabha Centre for Science Education, TIFR, V. N. Purav Marg, Mankhurd, Mumbai 400088 (India); Antia, H. M. [Tata Institute of Fundamental Research, Homi Bhabha Road, Mumbai 400005 (India); Basu, Sarbani, E-mail: kuldeep@phys.au.dk [Astronomy Department, Yale University, P.O. Box 208101, New Haven, CT 065208101 (United States)

2017-03-01

Acoustic glitches are regions inside a star where the sound speed or its derivatives change abruptly. These leave a small characteristic oscillatory signature in the stellar oscillation frequencies. With the precision achieved by Kepler seismic data, it is now possible to extract these small amplitude oscillatory signatures, and infer the locations of the glitches. We perform glitch analysis for all the 66 stars in the Kepler seismic LEGACY sample to derive the locations of the base of the envelope convection zone (CZ) and the helium ionization zone. The signature from helium ionization zone is found to be robust for all stars in the sample, whereas the CZ signature is found to be weak and problematic, particularly for relatively massive stars with large errorbars on the oscillation frequencies. We demonstrate that the helium glitch signature can be used to constrain the properties of the helium ionization layers and the helium abundance.

Balanced sampling

NARCIS (Netherlands)

Brus, D.J.

2015-01-01

In balanced sampling a linear relation between the soil property of interest and one or more covariates with known means is exploited in selecting the sampling locations. Recent developments make this sampling design attractive for statistical soil surveys. This paper introduces balanced sampling

Location in Mobile Networks Using Database Correlation (DCM

Directory of Open Access Journals (Sweden)

Michal Mada

2008-01-01

Full Text Available The article presents one of the methods of location (DCM, which is suitable for using in urban environments, where other methods are less accurate. The principle of this method is in comparison of measured samples of signal with samples stored in database. Next the article deals with methods for processing the data and other possibilities of correction of location.

Location, location, location: Extracting location value from house prices

OpenAIRE

Kolbe, Jens; Schulz, Rainer; Wersing, Martin; Werwatz, Axel

2012-01-01

The price for a single-family house depends both on the characteristics of the building and on its location. We propose a novel semiparametric method to extract location values from house prices. After splitting house prices into building and land components, location values are estimated with adaptive weight smoothing. The adaptive estimator requires neither strong smoothness assumptions nor local symmetry. We apply the method to house transactions from Berlin, Germany. The estimated surface...

Zone-based RSS Reporting for Location Fingerprinting

DEFF Research Database (Denmark)

Kjærgaard, Mikkel Baun; Treu, Georg; Linnhoff–Popien, Claudia

2007-01-01

In typical location fingerprinting systems a tracked terminal reports sampled Received Signal Strength (RSS) values to a location server, which estimates its position based on a database of pre-recorded RSS fingerprints. So far, poll-based and periodic RSS reporting has been proposed. However......, for supporting proactive Location-based Services (LBSs), triggered by pre-defined spatial events, the periodic protocol is inefficient. Hence, this paper introduces zone-based RSS reporting: the location server translates geographical zones defined by the LBS into RSS-based representations, which are dynamically...

100 Area Columbia River sediment sampling

International Nuclear Information System (INIS)

Weiss, S.G.

1993-01-01

Forty-four sediment samples were collected from 28 locations in the Hanford Reach of the Columbia River to assess the presence of metals and man-made radionuclides in the near shore and shoreline settings of the Hanford Site. Three locations were sampled upriver of the Hanford Site plutonium production reactors. Twenty-two locations were sampled near the reactors. Three locations were sampled downstream of the reactors near the Hanford Townsite. Sediment was collected from depths of 0 to 6 in. and between 12 to 24 in. below the surface. Samples containing concentrations of metals exceeding the 95 % upper threshold limit values (DOE-RL 1993b) are considered contaminated. Contamination by arsenic, chromium, copper, lead, and zinc was found. Man-made radionuclides occur in all samples except four collected opposite the Hanford Townsite. Man-made radionuclide concentrations were generally less than 1 pCi/g

100 Area Columbia River sediment sampling

Energy Technology Data Exchange (ETDEWEB)

Weiss, S.G. [Westinghouse Hanford Co., Richland, WA (United States)

1993-09-08

Forty-four sediment samples were collected from 28 locations in the Hanford Reach of the Columbia River to assess the presence of metals and man-made radionuclides in the near shore and shoreline settings of the Hanford Site. Three locations were sampled upriver of the Hanford Site plutonium production reactors. Twenty-two locations were sampled near the reactors. Three locations were sampled downstream of the reactors near the Hanford Townsite. Sediment was collected from depths of 0 to 6 in. and between 12 to 24 in. below the surface. Samples containing concentrations of metals exceeding the 95 % upper threshold limit values (DOE-RL 1993b) are considered contaminated. Contamination by arsenic, chromium, copper, lead, and zinc was found. Man-made radionuclides occur in all samples except four collected opposite the Hanford Townsite. Man-made radionuclide concentrations were generally less than 1 pCi/g.

Determining the spatial variability of personal sampler inlet locations.

Science.gov (United States)

Vinson, Robert; Volkwein, Jon; McWilliams, Linda

2007-09-01

This article examines the spatial variability of dust concentrations within a coal miner's breathing zone and the impact of sampling location at the cap lamp, nose, and lapel. Tests were conducted in the National Institute for Safety and Health Pittsburgh Research Laboratory full-scale, continuous miner gallery using three prototype personal dust monitors (PDM). The dust masses detected by the PDMs were used to calculate the percentage difference of dust mass between the cap lamp and the nose and between the lapel and the nose. The calculated percentage differences of the masses ranged from plus 12% to minus 25%. Breathing zone tests were also conducted in four underground coal mines using the torso of a mannequin to simulate a miner. Coal mine dust was sampled with multi-cyclone sampling cans mounted directly in front of the mannequin near the cap lamp, nose, and lapel. These four coal mine tests found that the spatial variability of dust levels and imprecision of the current personal sampler is a greater influence than the sampler location within the breathing zone. However, a one-sample t-test of this data did find that the overall mean value of the cap lamp/nose ratio was not significantly different than 1 (p-value = 0.21). However, when applied to the overall mean value of the lapel/nose ratio there was a significant difference from 1 (p-value sampling location for coal mine dust samples. But these results suggest that the cap location is slightly more indicative of what is breathed through the nose area.

Lake Beach Monitoring Locations in Iowa

Data.gov (United States)

Iowa State University GIS Support and Research Facility — Monitored state lake beach locations in Iowa. The Watershed Monitoring & Assessment Section of the Iowa DNR takes regular water samples at these listed beaches...

Iowa Geologic Sampling Points

Data.gov (United States)

Iowa State University GIS Support and Research Facility — Point locations of geologic samples/files in the IGS repository. Types of samples include well cuttings, outcrop samples, cores, drillers logs, measured sections,...

Location of colorectal cancer: colonoscopy versus surgery. Yield of colonoscopy in predicting actual location.

Science.gov (United States)

Blum-Guzman, Juan Pablo; Wanderley de Melo, Silvio

2017-07-01

 Recent studies suggest that differences in biological characteristics and risk factors across cancer site within the colon and rectum may translate to differences in survival. It can be challenging at times to determine the precise anatomical location of a lesion with a luminal view during colonoscopy. The aim of this study is to determine if there is a significant difference between the location of colorectal cancers described by gastroenterologists in colonoscopies and the actual anatomical location noted on operative and pathology reports after colon surgery.  A single-center retrospective analysis of colonoscopies of patient with reported colonic masses from January 2005 to April 2014 (n = 380) was carried. Assessed data included demography, operative and pathology reports. Findings were compared: between the location of colorectal cancers described by gastroenterologists in colonoscopies and the actual anatomical location noted on operative reports or pathology samples.  We identified 380 colonic masses, 158 were confirmed adenocarcinomas. Of these 123 underwent surgical resection, 27 had to be excluded since no specific location was reported on their operative or pathology report. An absolute difference between endoscopic and surgical location was found in 32 cases (33 %). Of these, 22 (23 %) differed by 1 colonic segment, 8 (8 %) differed by 2 colonic segments and 2 (2 %) differed by 3 colonic segments.  There is a significant difference between the location of colorectal cancers reported by gastroenterologists during endoscopy and the actual anatomical location noted on operative or pathology reports after colon surgery. Endoscopic tattooing should be used when faced with any luminal lesions of interest.

Locating Longitudinal Respondents After a 50-Year Hiatus

Directory of Open Access Journals (Sweden)

Stone Celeste

2014-06-01

Full Text Available Many longitudinal and follow-up studies face a common challenge: locating study participants. This study examines the extent to which a geographically dispersed subsample of participants can be relocated after 37 to 51 years of noncontact. Relying mostly on commercially available databases and administrative records, the 2011-12 Project Talent Follow-up Pilot Study (PTPS12 located nearly 85 percent of the original sample members, many of whom had not participated in the study since 1960. This study uses data collected in the base year to examine which subpopulations were the hardest to find after this extended hiatus. The results indicate that females were located at significantly lower rates than males. As expected, sample members with lower cognitive abilities were among the hardest-to-reach subpopulations. We next evaluate the extent to which biases introduced during the tracking phase can be minimized by using the multivariate chi-square automatic interaction detection (CHAID technique to calculate tracking loss adjustments. Unlike a 1995 study that found that these adjustments reduced statistical biases among its sample of located females, our results suggest that statistical adjustments were not as effective in PTPS12, where many participants had not been contacted in nearly 50 years and the tracking rates varied so greatly across subgroups.

Location, location, location

NARCIS (Netherlands)

Anderson, S.P.; Goeree, J.K.; Ramer, R.

1997-01-01

We analyze the canonical location-then-price duopoly game with general log- concave consumer densities. A unique pure-strategy equilibrium to the two-stage game exists if the density is not "too asymmetric" and not "too concave." These criteria are satisfied by many commonly used densities.

Effects of steaming on contaminants of emerging concern levels in seafood

DEFF Research Database (Denmark)

Barbosa, Vera; Maulvault, Ana Luísa; Alves, Ricardo N

2018-01-01

in contaminant levels was observed after steaming, though varying according to contaminant and seafood species (e.g. iAs, perfluorobutanoate, dibenzo(ah)anthracene in Mytilus edulis, HHCB-Lactone in Solea sp., 2-Ethylhexyl salicylate in Lophius piscatorius). Furthermore, the increase in some CeCs, like Pb, Me...

Multimodal location estimation of videos and images

CERN Document Server

Friedland, Gerald

2015-01-01

This book presents an overview of the field of multimodal location estimation, i.e. using acoustic, visual, and/or textual cues to estimate the shown location of a video recording. The authors' sample research results in this field in a unified way integrating research work on this topic that focuses on different modalities, viewpoints, and applications. The book describes fundamental methods of acoustic, visual, textual, social graph, and metadata processing as well as multimodal integration methods used for location estimation. In addition, the text covers benchmark metrics and explores the limits of the technology based on a human baseline. ·         Discusses localization of multimedia data; ·         Examines fundamental methods of establishing location metadata for images and videos (other than GPS tagging); ·         Covers Data-Driven as well as Semantic Location Estimation.

Locating industrial VOC sources with aircraft observations

International Nuclear Information System (INIS)

Toscano, P.; Gioli, B.; Dugheri, S.; Salvini, A.; Matese, A.; Bonacchi, A.; Zaldei, A.; Cupelli, V.; Miglietta, F.

2011-01-01

Observation and characterization of environmental pollution, focussing on Volatile Organic Compounds (VOCs), in a high-risk industrial area, are particularly important in order to provide indications on a safe level of exposure, indicate eventual priorities and advise on policy interventions. The aim of this study is to use the Solid Phase Micro Extraction (SPME) method to measure VOCs, directly coupled with atmospheric measurements taken on a small aircraft environmental platform, to evaluate and locate the presence of VOC emission sources in the Marghera industrial area. Lab analysis of collected SPME fibres and subsequent analysis of mass spectrum and chromatograms in Scan Mode allowed the detection of a wide range of VOCs. The combination of this information during the monitoring campaign allowed a model (Gaussian Plume) to be implemented that estimates the localization of emission sources on the ground. - Highlights: → Flight plan aimed at sampling industrial area at various altitudes and locations. → SPME sampling strategy was based on plume detection by means of CO 2 . → Concentrations obtained were lower than the limit values or below the detection limit. → Scan mode highlighted presence of γ-butyrolactone (GBL) compound. → Gaussian dispersion modelling was used to estimate GBL source location and strength. - An integrated strategy based on atmospheric aircraft observations and dispersion modelling was developed, aimed at estimating spatial location and strength of VOC point source emissions in industrial areas.

Occurrence and Distribution of Organic Wastewater Compounds in Rock Creek Park, Washington, D.C., 2007-08

Science.gov (United States)

Phelan, Daniel J.; Miller, Cherie V.

2010-01-01

The U.S. Geological Survey, and the National Park Service Police Aviation Group, conducted a high-resolution, low-altitude aerial thermal infrared survey of the Washington, D.C. section of Rock Creek Basin within the Park boundaries to identify specific locations where warm water was discharging from seeps or pipes to the creek. Twenty-three stream sites in Rock Creek Park were selected based on the thermal infrared images. Sites were sampled during the summers of 2007 and 2008 for the analysis of organic wastewater compounds to verify potential sources of sewage and other anthropogenic wastewater. Two sets of stormwater samples were collected, on June 27-28 and September 6, 2008, at the Rock Creek at Joyce Road water-quality station using an automated sampler that began sampling when a specified stage threshold value was exceeded. Passive-sampler devices that accumulate organic chemicals over the duration of deployment were placed in July 2008 at the five locations that had the greatest number of detections of organic wastewater compounds from the June 2007 base-flow sampling. During the 2007 base-flow synoptic sampling, there were ubiquitous low-level detections of dissolved organic wastewater indicator compounds such as DEET, caffeine, HHCB, and organophosphate flame retardants at more than half of the 23 sites sampled in Rock Creek Park. Concentrations of DEET and caffeine in the tributaries to Rock Creek were variable, but in the main stem of Rock Creek, the concentrations were constant throughout the length of the creek, which likely reflects a distributed source. Organophosphate flame retardants in the main stem of Rock Creek were detected at estimated concentrations of 0.2 micrograms per liter or less, and generally did not increase with distance downstream. Overall, concentrations of most wastewater indicators in whole-water samples in the Park were similar to the concentrations found at the upstream sampling station at the Maryland/District of Columbia

Using Pictures to Assess Pain Location in Children.

Science.gov (United States)

Mesko, Phyllis J; Eliades, Aris Beoglos

2018-06-01

This study uses the Pain Area Locator (PAL) tool, a picture communication aid with body and medical equipment icons, to identify pain location in postoperative pediatric patients and assesses discrepancies between nurses' pain location assessment and pain location identified using the PAL tool. This descriptive study used a quantitative, comparative design, with a convenience sample of pediatric postoperative patients undergoing same-day surgeries at a free-standing, acute care, Magnet designated pediatric hospital. The child's pain location was assessed by asking the child to point to one of the 12 pictures on the PAL tool of where they hurt. All 41 (100%) of the postoperative children in the study demonstrated ability to use the PAL tool. The child identified a pain location in 34 assessments (83%) when the nurse documented no pain location. This investigation expands on previous evidence supporting that children can use the PAL tool to identify the pain location postoperatively. Copyright © 2016 American Society of PeriAnesthesia Nurses. Published by Elsevier Inc. All rights reserved.

Reliability testing of failed fuel location system

International Nuclear Information System (INIS)

Vieru, G.

1996-01-01

This paper presents the experimental reliability tests performed in order to prove the reliability parameters for Failed Fuel Location System (FFLS), equipment used to detect in which channel of a particular heat transport loop a fuel failure is located, and to find in which channel what particular bundle pair is failed. To do so, D20 samples from each reactor channel are sequentially monitored to detect a comparatively high level of delayed neutron activity. 15 refs, 8 figs, 2 tabs

Superfund Site Information - Site Sampling Data

Data.gov (United States)

U.S. Environmental Protection Agency — This asset includes Superfund site-specific sampling information including location of samples, types of samples, and analytical chemistry characteristics of...

Stroke Location Is an Independent Predictor of Cognitive Outcome.

Science.gov (United States)

Munsch, Fanny; Sagnier, Sharmila; Asselineau, Julien; Bigourdan, Antoine; Guttmann, Charles R; Debruxelles, Sabrina; Poli, Mathilde; Renou, Pauline; Perez, Paul; Dousset, Vincent; Sibon, Igor; Tourdias, Thomas

2016-01-01

On top of functional outcome, accurate prediction of cognitive outcome for stroke patients is an unmet need with major implications for clinical management. We investigated whether stroke location may contribute independent prognostic value to multifactorial predictive models of functional and cognitive outcomes. Four hundred twenty-eight consecutive patients with ischemic stroke were prospectively assessed with magnetic resonance imaging at 24 to 72 hours and at 3 months for functional outcome using the modified Rankin Scale and cognitive outcome using the Montreal Cognitive Assessment (MoCA). Statistical maps of functional and cognitive eloquent regions were derived from the first 215 patients (development sample) using voxel-based lesion-symptom mapping. We used multivariate logistic regression models to study the influence of stroke location (number of eloquent voxels from voxel-based lesion-symptom mapping maps), age, initial National Institutes of Health Stroke Scale and stroke volume on modified Rankin Scale and MoCA. The second part of our cohort was used as an independent replication sample. In univariate analyses, stroke location, age, initial National Institutes of Health Stroke Scale, and stroke volume were all predictive of poor modified Rankin Scale and MoCA. In multivariable analyses, stroke location remained the strongest independent predictor of MoCA and significantly improved the prediction compared with using only age, initial National Institutes of Health Stroke Scale, and stroke volume (area under the curve increased from 0.697-0.771; difference=0.073; 95% confidence interval, 0.008-0.155). In contrast, stroke location did not persist as independent predictor of modified Rankin Scale that was mainly driven by initial National Institutes of Health Stroke Scale (area under the curve going from 0.840 to 0.835). Similar results were obtained in the replication sample. Stroke location is an independent predictor of cognitive outcome (MoCA) at 3

Source Location of Noble Gas Plumes

International Nuclear Information System (INIS)

Hoffman, I.; Ungar, K.; Bourgouin, P.; Yee, E.; Wotawa, G.

2015-01-01

In radionuclide monitoring, one of the most significant challenges from a verification or surveillance perspective is the source location problem. Modern monitoring/surveillance systems employ meteorological source reconstruction — for example, the Fukushima accident, CRL emissions analysis and even radon risk mapping. These studies usually take weeks to months to conduct, involving multidisciplinary teams representing meteorology; dispersion modelling; radionuclide sampling and metrology; and, when relevant, proper representation of source characteristics (e.g., reactor engineering expertise). Several different approaches have been tried in an attempt to determine useful techniques to apply to the source location problem and to develop rigorous methods that combine all potentially relevant observations and models to identify a most probable source location and size with uncertainties. The ultimate goal is to understand the utility and limitations of these techniques so they can transition from R&D to operational tools. (author)

Automatic cross-sectioning and monitoring system locates defects in electronic devices

Science.gov (United States)

Jacobs, G.; Slaughter, B.

1971-01-01

System consists of motorized grinding and lapping apparatus, sample holder, and electronic control circuit. Low power microscope examines device to pinpoint location of circuit defect, and monitor displays output signal when defect is located exactly.

Network and adaptive sampling

CERN Document Server

Chaudhuri, Arijit

2014-01-01

Combining the two statistical techniques of network sampling and adaptive sampling, this book illustrates the advantages of using them in tandem to effectively capture sparsely located elements in unknown pockets. It shows how network sampling is a reliable guide in capturing inaccessible entities through linked auxiliaries. The text also explores how adaptive sampling is strengthened in information content through subsidiary sampling with devices to mitigate unmanageable expanding sample sizes. Empirical data illustrates the applicability of both methods.

UMTRA water sampling and analysis plan, Green River, Utah

International Nuclear Information System (INIS)

Papusch, R.

1993-12-01

The purpose of this water sampling and analysis plan (WSAP) is to provide a basis for groundwater and surface water sampling at the Green River Uranium Mill Tailing Remedial Action (UMTRA) Project site. This WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the monitoring locations

Location, Location, Location: Does Place Provide the Opportunity for Differentiation for Universities?

Science.gov (United States)

Winter, Emma; Thompson-Whiteside, Helen

2017-01-01

The fiercely competitive HE market has led HEIs to invest significant resources in building a distinct identity. An HEI's location forms an inherent part of its identity and the uniqueness of location offers an opportunity to differentiate. However there has been limited examination of how location is used by HEIs and little consideration of how…

Aflatoxin contamination of maize from different storage locations in Ghana

International Nuclear Information System (INIS)

Akrobortu, Dick Emmanuel

2008-05-01

The contamination of maize by aflatoxins in Ghana is of major concern because of the health hazards associated with it. This study focused on the role played by variations in climatic factors such as relative humidity and rainfall on aflatoxin contamination of maize in different maize storage locations. The study was carried out on samples collected over a period of 10 years (1990 to 1999) in three Districts (Ejura-Sekyedumase, Afram Plains/North-Kwahu and Nkoranza) well – known for maize production in Ghana. The aim was to study the influence of storage locations on levels of aflatoxin contamination and distribution in maize. The findings indicated that significant difference exists between the aflatoxin contamination levels of samples collected from Ejura-Sekyedumase and Nkoranza (p<0.05). Also there was a significant difference between the aflatoxin contamination levels of samples collected from Ejura-Sekyedumase and North-Kwahu (p<0.05). There was no significant difference between the contamination levels of samples from North- Kwahu and Nkoranza (p>0.05). The total aflatoxin levels in samples from Ejura-Sekyedumase, North-Kwahu and Nkoranza over the period were 120.50 ppb, 153.20 ppb and 134.17 ppb respectively. For the period 1990 to 1999 the aflatoxin distributions in the storage locations showed that Nkoranza had the highest level in 1997 and 1999 while North-Kwahu had the highest in 1990, 1991, 1993 and 1998. Similarly, Nkoranza and North-Kwahu had equal levels of 10.50 ppb in 1995. The three locations had equal levels of 9.50 ppb in 1994. On the whole, Ejura-Sekyedumase had fair distribution levels since it was the only location with its highest level far below the acceptable level of 20 ppb for humans. I hereby recommend that further research must be conducted in other districts in the country in order to create awareness of the health hazards associated with the aflatoxin contamination. (au)

Maintenance of tactile short-term memory for locations is mediated by spatial attention.

Science.gov (United States)

Katus, Tobias; Andersen, Søren K; Müller, Matthias M

2012-01-01

According to the attention-based rehearsal hypothesis, maintenance of spatial information is mediated by covert orienting towards memorized locations. In a somatosensory memory task, participants simultaneously received bilateral pairs of mechanical sample pulses. For each hand, sample stimuli were randomly assigned to one of three locations (fingers). A subsequent visual retro-cue determined whether the left or right hand sample was to be memorized. The retro-cue elicited lateralized activity reflecting the location of the relevant sample stimulus. Sensory processing during the retention period was probed by task-irrelevant pulses randomized to locations at the cued and uncued hand. The somatosensory N140 was enhanced for probes delivered to the cued hand, relative to uncued. Probes presented shortly after the retro-cue showed greatest attentional modulations. This suggests that transient contributions from retrospective selection overlapped with the sustained effect of attention-based rehearsal. In conclusion, focal attention shifts within tactile mnemonic content occurred after retro-cues and guided sensory processing during retention. Copyright © 2011 Elsevier B.V. All rights reserved.

Common Nearly Best Linear Estimates of Location and Scale ...

African Journals Online (AJOL)

Common nearly best linear estimates of location and scale parameters of normal and logistic distributions, which are based on complete samples, are considered. Here, the population from which the samples are drawn is either normal or logistic population or a fusion of both distributions and the estimates are computed ...

Summit crater lake observations, and the location, chemistry, and pH of water samples near Mount Chiginagak volcano, Alaska: 2004-2012

Science.gov (United States)

Schaefer, Janet R.; Scott, William E.; Evans, William C.; Wang, Bronwen; McGimsey, Robert G.

2013-01-01

maximum depth of 45 m (resulting pH ~2.9), and preventing the annual salmon run in the King Salmon River. A simultaneous release of gas and acidic aerosols from the crater caused widespread vegetation damage along the flow path. Since 2005, we have been monitoring the crater lake water that continues to flow into Mother Goose Lake by collecting surface water samples for major cation and anion analysis, measuring surface-water pH of affected drainages, and photo-documenting the condition of the summit crater lake. This report describes water sampling locations, provides a table of chemistry and pH measurements, and documents the condition of the summit crater between 2004 and 2011. In September 2013, the report was updated with results of water-chemistry samples collected in 2011 and 2012, which were added as an addendum.

Determination of the Number of Fixture Locating Points for Sheet Metal By Grey Model

Directory of Open Access Journals (Sweden)

Yang Bo

2017-01-01

Full Text Available In the process of the traditional fixture design for sheet metal part based on the "N-2-1" locating principle, the number of fixture locating points is determined by trial and error or the experience of the designer. To that end, a new design method based on grey theory is proposed to determine the number of sheet metal fixture locating points in this paper. Firstly, the training sample set is generated by Latin hypercube sampling (LHS and finite element analysis (FEA. Secondly, the GM(1, 1 grey model is constructed based on the established training sample set to approximate the mapping relationship between the number of fixture locating points and the concerned sheet metal maximum deformation. Thirdly, the final number of fixture locating points for sheet metal can be inversely calculated under the allowable maximum deformation. Finally, a sheet metal case is conducted and the results indicate that the proposed approach is effective and efficient in determining the number of fixture locating points for sheet metal.

Sample Return Robot

Data.gov (United States)

National Aeronautics and Space Administration — This Challenge requires demonstration of an autonomous robotic system to locate and collect a set of specific sample types from a large planetary analog area and...

Does location congruence matter? : a field study on the effects of location based advertising on perceived adintrusiveness, relevance and value

NARCIS (Netherlands)

Hühn, A.E.; Khan, J.V.; Ketelaar, P.; van t Riet, J.J.; Batalas, N.; König, R.; Rozendaal, E.; Markopoulos, P.

2017-01-01

We investigate the effect of location-congruent mobile messages on perceived intrusiveness, value, and relevance through a field experiment using the Experience Sampling Method (ESM). We developed a mobile application for undergraduate students, featuring campus news and information concerning class

Does location congruence matter? A field study on the effects of location-based advertising on perceived AD intrusiveness, relevance & value

NARCIS (Netherlands)

Hühn, A.E.; Khan, V.J.; Ketelaar, P.E.; Riet, J.P. van 't; Konig, R.P.; Rozendaal, E.; Batalas, N.; Markopoulos, P.

2017-01-01

We investigate the effect of location-congruent mobile messages on perceived intrusiveness, value, and relevance through a field experiment using the Experience Sampling Method (ESM). We developed a mobile application for undergraduate students, featuring campus news and information concerning class

Bioconcentration and acute toxicity of polycyclic musks in two benthic organisms (Chironomus riparius and Lumbriculus variegatus)

NARCIS (Netherlands)

Artola-Garicano, E.; Sinnige, T.L.; Holsteijn, I. van; Vaes, W.H.J.; Hermens, J.L.M.

2003-01-01

In the current study, the bioconcentration behavior and acute toxicity of two polycyclic musks, Tonalide® 7-acetyl-1,1,3,4,4,6,-hexamethyl-1,2,3,4,-tetrahydronaphthalene (AHTN) and Galaxolide® 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexa-methyl-cyclopenta[γ]-2- benzopyran (HHCB), were studied in two

Explaining preferences for home surroundings and locations

DEFF Research Database (Denmark)

Andersen, Hans Skifter

2011-01-01

This article is based on a survey carried out in Denmark that asked a random sample of the population about their preferences for home surroundings and locations. It shows that the characteristics of social surroundings are very important and can be divided into three independent dimensions......: avoiding social nuisances, preferring social homogeneity and living close to one’s social network and place of origin. The study shows that most people have many detailed preferences, whereas some have very few. This confirms an earlier theory that some people are very connected to certain places...... with given characteristics and thus do not have priorities regarding home surroundings and locations. For others, mostly young people and singles, home is just a place to sleep and relax, whereas life is lived elsewhere. For this group, there are only preferences for location and there are few specific...

Long-term effects of OBM cutting discharges at 12 locations on the Dutch continental shelf

International Nuclear Information System (INIS)

Daan, R.; Mulder, M.

1996-01-01

A sampling programme was carried out in 1994 and 1995 covering 12 well sites where OBM cuttings had been discharged 7 to 13 years ago. The locations were selected in areas with different sediment types. In terms of amounts of base oil discharged the discharge loads ranged from 13 to 298 tonnes. The locations included actual production platforms but also abandoned well sites. At each location compendious surveys were carried out, during which 4 stations were sampled at distances between 100 and 2000m from the discharge site. Sediment samples for chemical analysis were collected at all stations and numbers of the OBM-sensitive species Echinocardium cordatum were counted in all samples. Additional macrofauna analyses were performed for 5 locations. The chemical analyses revealed elevated oil concentrations at 5 of the 12 locations, but traces of oil were visually observed in a few samples at another 2 locations. Maximum concentrations, measured over the upper 10 cm layer, were generally in the order of 10-50 mg/kg dry sediment, but at one location a concentration of 200 mg/kg was found, which is comparable to the values found at formerly investigated locations L4-a and P6-b, but considerably lower than at K12-a. This indicates that concentration levels at most locations are generally not as high as found at the locations formerly investigated. Except for one location where oil was found up to 250m from the platform, elevated oil concentrations in surface sediments only occurred at 100m stations. Significant effects on the population densities of E. cordatum were found at 7 of the 12 locations. Further, at 2 locations the abundance pattern of the species was indicative of an effect but there was no statistical significance. Population densities of E. cordaturn appeared to be depressed in the vicinity of two locations where no oil was detected. This indicates that the absence of oil in samples does not necessarily mean that sediment conditions have completely recovered

Location-specific immunodetection of cocaine on banknotes.

Science.gov (United States)

van der Heide, Susan; Cunningham, Andrew; Hardwick, Sheila; Russell, David A

2016-10-17

A novel in-gel bioanalytical immunodetection method has been developed to determine both the presence and the location of cocaine on the surface of banknotes. The cocaine was 'fixed' to the surface of the banknote via a coating of a polyacrylamide gel matrix. Immunostaining of the immobilised cocaine on the banknote surface was performed using an anti-cocaine primary antibody, either pre-labelled with horse radish peroxidase (HRP) or in conjunction with a HRP-labelled secondary antibody. Visualisation of the location of the cocaine was achieved through chemiluminescence imaging of the banknote following application of a chemiluminescent substrate. The novel method was applied to the detection of cocaine on partial and whole banknote samples obtained from general circulation. Newly minted banknotes, with or without spiked cocaine, were used as positive and negative controls, respectively. The results obtained, for the first time, demonstrate the successful location-specific immunostaining of cocaine on banknotes. A preliminary analysis of six UK banknotes, obtained from general circulation, suggests that cocaine can be present at variable locations across the whole of the banknote.

40 CFR 61.34 - Air sampling.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Air sampling. 61.34 Section 61.34... sampling. (a) Stationary sources subject to § 61.32(b) shall locate air sampling sites in accordance with a... concentrations calculated within 30 days after filters are collected. Records of concentrations at all sampling...

Cleaning and Processing RSS measurements for Location Fingerprinting

DEFF Research Database (Denmark)

Kjærgaard, Mikkel Baun

2007-01-01

Handling variations in sampled Received Signal Strength (RSS) is neassary for achieving robust location fingerprinting (LF). Current research has only proposed limited system-specific models for how to handle the cleaning of RSS variations. However, this paper propose a novel model for both...

A Simultaneous Study of Outsourcing and Location Choices

DEFF Research Database (Denmark)

Leiblein, Michael J.; Møller Larsen, Marcus; Pedersen, Torben

This paper simultaneously evaluates factors affecting decisions regarding the organization and location of economic activity. The paper uses data from a comprehensive sample of exchanges involving public and private global semiconductor firms over the 1990 to 2005 time period. The paper accounts...

A Simultaneous Examination of Outsourcing and Location Choices

DEFF Research Database (Denmark)

Leiblein, Michael J.; Larsen, Marcus M.; Pedersen, Torben

2014-01-01

This paper simultaneously evaluates factors affecting decisions regarding the organization and location of economic activity. The paper uses data from a comprehensive sample of exchanges involving public and private global semiconductor firms over the 1990 to 2005 time period. The paper accounts ...

A Location Privacy Aware Friend Locator

DEFF Research Database (Denmark)

Siksnys, Laurynas; Thomsen, Jeppe Rishede; Saltenis, Simonas

2009-01-01

to trade their location privacy for quality of service, limiting the attractiveness of the services. The challenge is to develop a communication-efficient solution such that (i) it detects proximity between a user and the user’s friends, (ii) any other party is not allowed to infer the location of the user...

A patient's view on the location of the temporomandibular joint.

Science.gov (United States)

Koole, Paul; Zonnenberg, Adriaan J J; Mulder, Jan

2018-03-25

Objective A survey was held to establish whether laypeople knew the location of their temporomandibular joint. Methods A sample of 61 participants, visiting their dental office for a routine check-up, was given a three-question survey of whether they knew the location of their temporomandibular joint and could point to this location. Results Thirty-eight participants answered the question affirmatively. Only 13 pointed to the correct location. Of these, six participants received consultation for TMD in the past, three participants were healthcare providers, and four participants actually had knowledge of the exact location. Out of 23 participants who did not know the location, one accidently designated the correct position. Conclusion The location of the temporomandibular joint is not a well-known site for many patients. In the presence of orofacial pain, it seems advisable to let the patient designate and record the site of the pain on a drawing on the patient chart.

Sampling and analysis plan for the consolidated sludge samples from the canisters and floor of the 105-K East basin

International Nuclear Information System (INIS)

BAKER, R.B.

1999-01-01

This Sampling and Analysis Plan (SAP) provides direction for sampling of fuel canister and floor Sludge from the K East Basin to complete the inventory of samples needed for Sludge treatment process testing. Sample volumes and sources consider recent reviews made by the Sludge treatment subproject. The representative samples will be characterized to the extent needed for the material to be used effectively for testing. Sampling equipment used allows drawing of large volume sludge samples and consolidation of sample material from a number of basin locations into one container. Once filled, the containers will be placed in a cask and transported to Hanford laboratories for recovery and evaluation. Included in the present SAP are the logic for sample location selection, laboratory analysis procedures required, and reporting needed to meet the Data Quality Objectives (DQOs) for this initiative

40 CFR 89.507 - Sample selection.

Science.gov (United States)

2010-07-01

... Auditing § 89.507 Sample selection. (a) Engines comprising a test sample will be selected at the location...). However, once the manufacturer ships any test engine, it relinquishes the prerogative to conduct retests...

An antithetic variate to facilitate upper-stem height measurements for critical height sampling with importance sampling

Science.gov (United States)

Thomas B. Lynch; Jeffrey H. Gove

2013-01-01

Critical height sampling (CHS) estimates cubic volume per unit area by multiplying the sum of critical heights measured on trees tallied in a horizontal point sample (HPS) by the HPS basal area factor. One of the barriers to practical application of CHS is the fact that trees near the field location of the point-sampling sample point have critical heights that occur...

Location coding by opponent neural populations in the auditory cortex.

Directory of Open Access Journals (Sweden)

G Christopher Stecker

2005-03-01

Full Text Available Although the auditory cortex plays a necessary role in sound localization, physiological investigations in the cortex reveal inhomogeneous sampling of auditory space that is difficult to reconcile with localization behavior under the assumption of local spatial coding. Most neurons respond maximally to sounds located far to the left or right side, with few neurons tuned to the frontal midline. Paradoxically, psychophysical studies show optimal spatial acuity across the frontal midline. In this paper, we revisit the problem of inhomogeneous spatial sampling in three fields of cat auditory cortex. In each field, we confirm that neural responses tend to be greatest for lateral positions, but show the greatest modulation for near-midline source locations. Moreover, identification of source locations based on cortical responses shows sharp discrimination of left from right but relatively inaccurate discrimination of locations within each half of space. Motivated by these findings, we explore an opponent-process theory in which sound-source locations are represented by differences in the activity of two broadly tuned channels formed by contra- and ipsilaterally preferring neurons. Finally, we demonstrate a simple model, based on spike-count differences across cortical populations, that provides bias-free, level-invariant localization-and thus also a solution to the "binding problem" of associating spatial information with other nonspatial attributes of sounds.

PIXE analysis of thin samples

International Nuclear Information System (INIS)

Kiss, Ildiko; Koltay, Ede; Szabo, Gyula; Laszlo, S.; Meszaros, A.

1985-01-01

Particle-induced X-ray emission (PIXE) multielemental analysis of thin film samples are reported. Calibration methods of K and L X-lines are discussed. Application of PIXE analysis to aerosol monitoring, multielement aerosol analysis is described. Results of PIXE analysis of samples from two locations in Hungary are compared with the results of aerosol samples from Scandinavia and the USA. (D.Gy.)

Sampling and Analysis Plan for the 221-U Facility

International Nuclear Information System (INIS)

Rugg, J.E.

1998-02-01

This sampling and analysis plan (SAP) presents the rationale and strategy for the sampling and analysis activities proposed to be conducted to support the evaluation of alternatives for the final disposition of the 221-U Facility. This SAP will describe general sample locations and the minimum number of samples required. It will also identify the specific contaminants of potential concern (COPCs) and the required analysis. This SAP does not define the exact sample locations and equipment to be used in the field due to the nature of unknowns associated with the 221-U Facility

Locative media

CERN Document Server

Wilken, Rowan

2014-01-01

Not only is locative media one of the fastest growing areas in digital technology, but questions of location and location-awareness are increasingly central to our contemporary engagements with online and mobile media, and indeed media and culture generally. This volume is a comprehensive account of the various location-based technologies, services, applications, and cultures, as media, with an aim to identify, inventory, explore, and critique their cultural, economic, political, social, and policy dimensions internationally. In particular, the collection is organized around the perception that the growth of locative media gives rise to a number of crucial questions concerning the areas of culture, economy, and policy.

Elemental contents in soil samples in Wad Hamid, River Nile State

International Nuclear Information System (INIS)

Mohammed, Khansaa Elawad Elhag

2016-03-01

In the present study a total of 30 samples were collected from Wad Hamid River Nile State. Sampling area of (two feddan) of agricultural soil. The sampling area was divided in two locations (fertile and non fertile soil). The samples were analyzed for their content of 13 elements (K, Ca, Ti, Mn, Fe, Cu, Zn, Pb, Rb, Sr, Y, Zr, and Np). 10 samples from location 1 (non-fertile soil) and 20 samples from location 2 (fertile soil). X-ray fluorescence (X RF) Spectrometer (system used based on 1"0"9"Cd excitation 1"0"9"Cd source which has an average energy of 22.6 kev and able to excite the elements from Z = 13 to 92 using K and L lines) used to identify the elemental concentration in soil samples. The reliability of X RF technique as multi elements detecting method for measuring elements concentration in soil sample , (IAEA-SOIL-7) standard reference material was used. Measured values found in agreement with the certified values. The average elemental concentration of K,Ca, Ti, Fe, Cu, Zn, Pb, Sr, Y, Zr, and Np in location 1 were 878, 29690, 13400, 983, 70380, 10.07, 19.07, 40.92,261.4, 23.59,294.8, 47.82, while the average elemental concentration in location 2 were 9848, 27780, 13076,13076,989, 68135, 9.6, 96.3 19.86, 43.7, 225.5, 22.49, 284.75, 46.15, respectively. comparison between the average elemental concentration in fertile soil and non-fertile was done correlations between element were performed Cluster analyses of element in soil samples were obtained comparison between this study and data from literature were done. The elemental concentration in location 1 (non- fertile soil) are higher than location 2 ( fertile soil) because the plant absorbed fertilizer of soil and transfer most elements in soil to plant. (Author)

40 CFR 90.507 - Sample selection.

Science.gov (United States)

2010-07-01

... Auditing § 90.507 Sample selection. (a) Engines comprising a test sample will be selected at the location... manufacturer ships any test engine, it relinquishes the prerogative to conduct retests as provided in § 90.508...

Hanford Site Environmental Surveillance Master Sampling Schedule for Calendar Year 2011

Energy Technology Data Exchange (ETDEWEB)

Bisping, Lynn E.

2011-01-21

This document contains the calendar year 2011 schedule for the routine collection of samples for the Surface Environmental Surveillance Project and the Drinking Water Monitoring Project. Each section includes sampling locations, sampling frequencies, sample types, and analyses to be performed. In some cases, samples are scheduled on a rotating basis. If a sample will not be collected in 2011, the anticipated year for collection is provided. Maps showing approximate sampling locations are included for media scheduled for collection in 2011.

Household location choices: implications for biodiversity conservation.

Science.gov (United States)

Peterson, M Nils; Chen, Xiaodong; Liu, Jianguo

2008-08-01

Successful conservation efforts require understanding human behaviors that directly affect biodiversity. Choice of household location represents an observable behavior that has direct effects on biodiversity conservation, but no one has examined the sociocultural predictors of this choice relative to its environmental impacts. We conducted a case study of the Teton Valley of Idaho and Wyoming (U.S.A.) that (1) explored relationships between sociodemographic variables, environmental attitudes, and the environmental impact of household location choices, (2) assessed the potential for small household sizes in natural areas to multiply the environmental impacts of household location decisions, and (3) evaluated how length of residency predicted the environmental attitudes of people living in natural areas. We collected sociodemographic data, spatial coordinates, and land-cover information in a survey of 416 households drawn from a random sample of Teton Valley residents (95% compliance rate). Immigrants (respondents not born in the study area) with the lowest education levels and least environmentally oriented attitudes lived in previously established residential areas in disproportionately high numbers, and older and more educated immigrants with the most environmentally oriented attitudes lived in natural areas in disproportionately high numbers. Income was not a significant predictor of household location decisions. Those living in natural areas had more environmental impact per person because of the location and because small households (educated, and potentially growing more environmentally oriented, these patterns are troubling for biodiversity conservation. Our results demonstrate a need for environmentalists to make household location decisions that reflect their environmental attitudes and future research to address how interactions between education level, environmental attitudes, population aging, and household location choices influence biodiversity

Location of Urban Logistic Terminals as Hub Location Problem

Directory of Open Access Journals (Sweden)

Jasmina Pašagić Škrinjar

2012-09-01

Full Text Available In this paper the problems of locating urban logistic terminals are studied as hub location problems that due to a large number of potential nodes in big cities belong to hard non-polynomial problems, the so-called NP-problems. The hub location problems have found wide application in physical planning of transport and telecommunication systems, especially systems of fast delivery, networks of logistic and distribution centres and cargo traffic terminals of the big cities, etc. The paper defines single and multiple allocations and studies the numerical examples. The capacitated single allocation hub location problems have been studied, with the provision of a mathematical model of selecting the location for the hubs on the network. The paper also presents the differences in the possibilities of implementing the exact and heuristic methods to solve the actual location problems of big dimensions i.e. hub problems of the big cities.

Effects of sample size and sampling frequency on studies of brown bear home ranges and habitat use

Science.gov (United States)

Arthur, Steve M.; Schwartz, Charles C.

1999-01-01

We equipped 9 brown bears (Ursus arctos) on the Kenai Peninsula, Alaska, with collars containing both conventional very-high-frequency (VHF) transmitters and global positioning system (GPS) receivers programmed to determine an animal's position at 5.75-hr intervals. We calculated minimum convex polygon (MCP) and fixed and adaptive kernel home ranges for randomly-selected subsets of the GPS data to examine the effects of sample size on accuracy and precision of home range estimates. We also compared results obtained by weekly aerial radiotracking versus more frequent GPS locations to test for biases in conventional radiotracking data. Home ranges based on the MCP were 20-606 km2 (x = 201) for aerial radiotracking data (n = 12-16 locations/bear) and 116-1,505 km2 (x = 522) for the complete GPS data sets (n = 245-466 locations/bear). Fixed kernel home ranges were 34-955 km2 (x = 224) for radiotracking data and 16-130 km2 (x = 60) for the GPS data. Differences between means for radiotracking and GPS data were due primarily to the larger samples provided by the GPS data. Means did not differ between radiotracking data and equivalent-sized subsets of GPS data (P > 0.10). For the MCP, home range area increased and variability decreased asymptotically with number of locations. For the kernel models, both area and variability decreased with increasing sample size. Simulations suggested that the MCP and kernel models required >60 and >80 locations, respectively, for estimates to be both accurate (change in area bears. Our results suggest that the usefulness of conventional radiotracking data may be limited by potential biases and variability due to small samples. Investigators that use home range estimates in statistical tests should consider the effects of variability of those estimates. Use of GPS-equipped collars can facilitate obtaining larger samples of unbiased data and improve accuracy and precision of home range estimates.

Sampling wild species to conserve genetic diversity

Science.gov (United States)

Sampling seed from natural populations of crop wild relatives requires choice of the locations to sample from and the amount of seed to sample. While this may seem like a simple choice, in fact careful planning of a collector’s sampling strategy is needed to ensure that a crop wild collection will ...

Location, location, location: does early cancer in Barrett's esophagus have a preference?

Science.gov (United States)

Enestvedt, Brintha K; Lugo, Ricardo; Guarner-Argente, Carlos; Shah, Pari; Falk, Gary W; Furth, Emma; Ginsberg, Gregory G

2013-09-01

Early cancer (high-grade dysplasia [HGD] and intramucosal carcinoma [ImCa]) associated with Barrett's esophagus (BE) may have a circumferential spatial predilection. To describe the esophageal circumferential location of early cancer in BE. Retrospective study, single tertiary referral center. One hundred nineteen patients were referred for endoscopic eradication therapy for early cancer associated with BE. Endoscopic images and reports and pathology were reviewed. Circumferential location designation of early cancer in BE by using a clock-face orientation. One hundred nineteen of 131 patients referred for endoscopic eradication therapy had a location designation for their advanced histology (91.9%). There were a total of 57 patients (47.9%) with HGD and 62 patients (52.1%) with ImCa. There was a significantly higher rate of early cancer (HGD or ImCa) in the right hemisphere (12 to 6 o'clock location) compared with the left hemisphere (84.9% vs 15.1%, P cancer was found in the 12 to 3 o'clock quadrant (64.7%); 71.9% of HGD and 58.1% of ImCa lesions were located in the 12 to 3 o'clock quadrant. Retrospective design, single center. Early cancer associated with BE is far more commonly found in the right hemisphere of the esophagus (12 to 6 o'clock) with the highest rate in the 12 to 3 o'clock quadrant. These findings support enhanced scrutiny of the right hemisphere of the esophagus during surveillance and endoscopic treatment of patients with BE. Copyright © 2013 American Society for Gastrointestinal Endoscopy. Published by Mosby, Inc. All rights reserved.

Hanford Site Environmental Surveillance Master Sampling Schedule for Calendar Year 2007

Energy Technology Data Exchange (ETDEWEB)

Bisping, Lynn E.

2007-01-31

This document contains the calendar year 2007 schedule for the routine collection of samples for the Surface Environmental Surveillance Project and Drinking Water Monitoring Project. Each section includes sampling locations, sampling frequencies, sample types, and analyses to be performed. In some cases, samples are scheduled on a rotating basis and may not be collected in 2007 in which case the anticipated year for collection is provided. Maps showing approximate sampling locations are included for media scheduled for collection in 2007.

Environmental surveillance master sampling schedule

Energy Technology Data Exchange (ETDEWEB)

Bisping, L E

1992-01-01

Environmental surveillance of the Hanford Site and surrounding areas is conducted by the Pacific Northwest Laboratory (PNL) for the US Department of Energy (DOE). This document contains the planned schedule for routine sample collection for the Surface Environmental Surveillance Project (SESP) and Ground-Water Monitoring Project. Samples for radiological analyses include Air-Particulate Filter, gases and vapor; Water/Columbia River, Onsite Pond, Spring, Irrigation, and Drinking; Foodstuffs/Animal Products including Whole Milk, Poultry and Eggs, and Beef; Foodstuffs/Produce including Leafy Vegetables, Vegetables, and Fruit; Foodstuffs/Farm Products including Wine, Wheat and Alfalfa; Wildlife; Soil; Vegetation; and Sediment. Direct Radiation Measurements include Terrestrial Locations, Columbia River Shoreline Locations, and Onsite Roadway, Railway and Aerial, Radiation Surveys.

Hanford Site Environmental Surveillance Master Sampling Schedule

International Nuclear Information System (INIS)

Bisping, L.E.

1999-01-01

Environmental surveillance of the Hanford Site and surrounding areas is conducted by the Pacific Northwest National Laboratory (PNNL) for the U.S. Department of Energy (DOE). Sampling is conducted to evaluate levels of radioactive and nonradioactive pollutants in the Hanford environs, as required in DOE Order 5400.1, ''General Environmental protection Program,'' and DOE Order 5400.5, ''Radiation Protection of the Public and the Environment.'' The sampling methods are described in the Environmental Monitoring Plan, United States Department of Energy, Richland Operations Office, DOE/RL-91-50, Rev.2, U.S. Department of Energy, Richland, Washington. This document contains the CY1999 schedules for the routine collection of samples for the Surface Environmental Surveillance Project (SESP) and Drinking Water Monitoring Project. Each section includes the sampling location, sample type, and analyses to be performed on the sample. In some cases, samples are scheduled on a rotating basis and may not be collected in 1999 in which case the anticipated year for collection is provided. In addition, a map is included for each media showing approximate sampling locations

Leak Location of Pipeline with Multibranch Based on a Cyber-Physical System

Directory of Open Access Journals (Sweden)

Xianming Lang

2017-09-01

Full Text Available Data cannot be shared and leakage cannot be located simultaneously among multiple pipeline leak detection systems. Based on cyber-physical system (CPS architecture, the method for locating leakage for pipelines with multibranch is proposed. The singular point of pressure signals at the ends of pipeline with multibranch is analyzed by wavelet packet analysis, so that the time feature samples could be established. Then, the Fischer-Burmeister function is introduced into the learning process of the twin support vector machine (TWSVM in order to avoid the matrix inversion calculation, and the samples are input into the improved twin support vector machine (ITWSVM to distinguish the pipeline leak location. The simulation results show that the proposed method is more effective than the back propagation (BP neural networks, the radial basis function (RBF neural networks, and the Lagrange twin support vector machine.

Expectation-Maximization Tensor Factorization for Practical Location Privacy Attacks

Directory of Open Access Journals (Sweden)

Murakami Takao

2017-10-01

Full Text Available Location privacy attacks based on a Markov chain model have been widely studied to de-anonymize or de-obfuscate mobility traces. An adversary can perform various kinds of location privacy attacks using a personalized transition matrix, which is trained for each target user. However, the amount of training data available to the adversary can be very small, since many users do not disclose much location information in their daily lives. In addition, many locations can be missing from the training traces, since many users do not disclose their locations continuously but rather sporadically. In this paper, we show that the Markov chain model can be a threat even in this realistic situation. Specifically, we focus on a training phase (i.e. mobility profile building phase and propose Expectation-Maximization Tensor Factorization (EMTF, which alternates between computing a distribution of missing locations (E-step and computing personalized transition matrices via tensor factorization (M-step. Since the time complexity of EMTF is exponential in the number of missing locations, we propose two approximate learning methods, one of which uses the Viterbi algorithm while the other uses the Forward Filtering Backward Sampling (FFBS algorithm. We apply our learning methods to a de-anonymization attack and a localization attack, and evaluate them using three real datasets. The results show that our learning methods significantly outperform a random guess, even when there is only one training trace composed of 10 locations per user, and each location is missing with probability 80% (i.e. even when users hardly disclose two temporally-continuous locations.

Does the pretreatment tumor sampling location correspond with metabolic activity on 18F-FDG PET/CT in breast cancer patients scheduled for neoadjuvant chemotherapy?

Energy Technology Data Exchange (ETDEWEB)

Koolen, Bas B., E-mail: b.koolen@nki.nl [Department of Nuclear Medicine, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Department of Surgical Oncology, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Elshof, Lotte E. [Department of Nuclear Medicine, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Department of Surgical Oncology, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Loo, Claudette E. [Department of Radiology, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Wesseling, Jelle [Department of Pathology, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Vrancken Peeters, Marie-Jeanne T.F.D. [Department of Surgical Oncology, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Vogel, Wouter V. [Department of Nuclear Medicine, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Rutgers, Emiel J.Th. [Department of Surgical Oncology, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands); Valdés Olmos, Renato A. [Department of Nuclear Medicine, Netherlands Cancer Institute – Antoni van Leeuwenhoek Hospital, Plesmanlaan 121, 1066 CX Amsterdam (Netherlands)

2013-12-01

Purpose: To define the correlation between the core biopsy location and the area with highest metabolic activity on 18F-FDG PET/CT in stage II–III breast cancer patients before neoadjuvant chemotherapy. Also, we would like to select a subgroup of patients in which PET/CT information may optimize tumor sampling. Methods: A PET/CT in prone position was acquired in 199 patients with 203 tumors. The distance and relative difference in standardized uptake value (SUV) between core biopsy localization (indicated by a marker) and area with highest degree of FDG uptake were evaluated. A distance ≥2 cm and a relative difference in SUV ≥25% were considered clinically relevant and a combination of both was defined as non-correspondence. Non-correspondence for different tumor characteristics (TNM stage, lesion morphology on MRI and PET/CT, histology, subtype, grade, and Ki-67) was assessed. Results: Non-correspondence was found in 28 (14%) of 203 tumors. Non-correspondence was significantly associated with T-stage, lesion morphology on MRI and PET/CT, tumor diameter, and histologic type. It was more often seen in tumors with a higher T-stage (p = 0.028), diffuse (non-mass) and multifocal tumors on MRI (p = 0.001), diffuse and multifocal tumors on PET/CT (p < 0.001), tumors >3 cm (p < 0.001), and lobular carcinomas (p < 0.001). No association was found with other features. Conclusion: Non-correspondence between the core biopsy location and area with highest FDG uptake is regularly seen in stage II–III breast cancer patients. PET/CT information and possibly FDG-guided biopsies are most likely to improve pretreatment tumor sampling in tumors >3 cm, lobular carcinomas, and diffuse and multifocal tumors.

Sparse sampling and reconstruction for electron and scanning probe microscope imaging

Science.gov (United States)

Anderson, Hyrum; Helms, Jovana; Wheeler, Jason W.; Larson, Kurt W.; Rohrer, Brandon R.

2015-07-28

Systems and methods for conducting electron or scanning probe microscopy are provided herein. In a general embodiment, the systems and methods for conducting electron or scanning probe microscopy with an undersampled data set include: driving an electron beam or probe to scan across a sample and visit a subset of pixel locations of the sample that are randomly or pseudo-randomly designated; determining actual pixel locations on the sample that are visited by the electron beam or probe; and processing data collected by detectors from the visits of the electron beam or probe at the actual pixel locations and recovering a reconstructed image of the sample.

Reference Device-Assisted Adaptive Location Fingerprinting

Directory of Open Access Journals (Sweden)

Dongjin Wu

2016-06-01

Full Text Available Location fingerprinting suffers in dynamic environments and needs recalibration from time to time to maintain system performance. This paper proposes an adaptive approach for location fingerprinting. Based on real-time received signal strength indicator (RSSI samples measured by a group of reference devices, the approach applies a modified Universal Kriging (UK interpolant to estimate adaptive temporal and environmental radio maps. The modified UK can take the spatial distribution characteristics of RSSI into account. In addition, the issue of device heterogeneity caused by multiple reference devices is further addressed. To compensate the measuring differences of heterogeneous reference devices, differential RSSI metric is employed. Extensive experiments were conducted in an indoor field and the results demonstrate that the proposed approach not only adapts to dynamic environments and the situation of changing APs’ positions, but it is also robust toward measuring differences of heterogeneous reference devices.

What does visual suffix interference tell us about spatial location in working memory?

Science.gov (United States)

Allen, Richard J; Castellà, Judit; Ueno, Taiji; Hitch, Graham J; Baddeley, Alan D

2015-01-01

A visual object can be conceived of as comprising a number of features bound together by their joint spatial location. We investigate the question of whether the spatial location is automatically bound to the features or whether the two are separable, using a previously developed paradigm whereby memory is disrupted by a visual suffix. Participants were shown a sample array of four colored shapes, followed by a postcue indicating the target for recall. On randomly intermixed trials, a to-be-ignored suffix array consisting of two different colored shapes was presented between the sample and the postcue. In a random half of suffix trials, one of the suffix items overlaid the location of the target. If location was automatically encoded, one might expect the colocation of target and suffix to differentially impair performance. We carried out three experiments, cuing for recall by spatial location (Experiment 1), color or shape (Experiment 2), or both randomly intermixed (Experiment 3). All three studies showed clear suffix effects, but the colocation of target and suffix was differentially disruptive only when a spatial cue was used. The results suggest that purely visual shape-color binding can be retained and accessed without requiring information about spatial location, even when task demands encourage the encoding of location, consistent with the idea of an abstract and flexible visual working memory system.

Hanford Site Environmental Surveillance Master Sampling Schedule

International Nuclear Information System (INIS)

Bisping, L.E.

2000-01-01

Environmental surveillance of the Hanford Site and surrounding areas is conducted by the Pacific Northwest National Laboratory (PNNL) for the U.S. Department of Energy (DOE). Sampling is conducted to evaluate levels of radioactive and nonradioactive pollutants in the Hanford environs, as required in DOE Order 5400.1, General Environmental Protection Program: and DOE Order 5400.5, Radiation Protection of the Public and the Environment. The sampling design is described in the Operations Office, Environmental Monitoring Plan, United States Department of Energy, Richland DOE/RL-91-50, Rev.2, U.S. Department of Energy, Richland, Washington. This document contains the CY 2000 schedules for the routine collection of samples for the Surface Environmental Surveillance Project (SESP) and Drinking Water Monitoring Project. Each section includes sampling locations, sample types, and analyses to be performed. In some cases, samples are scheduled on a rotating basis and may not be collected in 2000 in which case the anticipated year for collection is provided. In addition, a map showing approximate sampling locations is included for each media scheduled for collection

Outpatient endometrial aspiration: an alternative to methotrexate for pregnancy of unknown location.

Science.gov (United States)

Insogna, Iris G; Farland, Leslie V; Missmer, Stacey A; Ginsburg, Elizabeth S; Brady, Paula C

2017-08-01

Pregnancies of unknown location with abnormal beta-human chorionic gonadotropin trends are frequently treated as presumed ectopic pregnancies with methotrexate. Preliminary data suggest that outpatient endometrial aspiration may be an effective tool to diagnose pregnancy location, while also sparing women exposure to methotrexate. The purpose of this study was to evaluate the utility of an endometrial sampling protocol for the diagnosis of pregnancies of unknown location after in vitro fertilization. A retrospective cohort study of 14,505 autologous fresh and frozen in vitro fertilization cycles from October 2007 to September 2015 was performed; 110 patients were diagnosed with pregnancy of unknown location, defined as a positive beta-human chorionic gonadotropin without ultrasound evidence of intrauterine or ectopic pregnancy and an abnormal beta-human chorionic gonadotropin trend (location, failed intrauterine pregnancy was diagnosed in 46 patients (42%), and ectopic pregnancy was diagnosed in 64 patients (58%). Clinical variables that included fresh or frozen embryo transfer, day of embryo transfer, serum beta-human chorionic gonadotropin at the time of sampling, endometrial thickness, and presence of an adnexal mass were not significantly different between patients with failed intrauterine pregnancy or ectopic pregnancy. In patients with failed intrauterine pregnancy, 100% demonstrated adequate postsampling beta-human chorionic gonadotropin declines; villi were identified in just 46% (n=21 patients). Patients with failed intrauterine pregnancy had significantly shorter time to resolution (negative serum beta-human chorionic gonadotropin) after sampling compared with patients with ectopic pregnancy (12.6 vs 26.3 days; Plocation are spared methotrexate, with a shorter time to pregnancy resolution than those who receive methotrexate. Copyright © 2017 Elsevier Inc. All rights reserved.

Kalman/Map Filtering-Aided Fast Normalized Cross Correlation-Based Wi-Fi Fingerprinting Location Sensing

Directory of Open Access Journals (Sweden)

Yongliang Sun

2013-11-01

Full Text Available A Kalman/map filtering (KMF-aided fast normalized cross correlation (FNCC-based Wi-Fi fingerprinting location sensing system is proposed in this paper. Compared with conventional neighbor selection algorithms that calculate localization results with received signal strength (RSS mean samples, the proposed FNCC algorithm makes use of all the on-line RSS samples and reference point RSS variations to achieve higher fingerprinting accuracy. The FNCC computes efficiently while maintaining the same accuracy as the basic normalized cross correlation. Additionally, a KMF is also proposed to process fingerprinting localization results. It employs a new map matching algorithm to nonlinearize the linear location prediction process of Kalman filtering (KF that takes advantage of spatial proximities of consecutive localization results. With a calibration model integrated into an indoor map, the map matching algorithm corrects unreasonable prediction locations of the KF according to the building interior structure. Thus, more accurate prediction locations are obtained. Using these locations, the KMF considerably improves fingerprinting algorithm performance. Experimental results demonstrate that the FNCC algorithm with reduced computational complexity outperforms other neighbor selection algorithms and the KMF effectively improves location sensing accuracy by using indoor map information and spatial proximities of consecutive localization results.

Kalman/Map filtering-aided fast normalized cross correlation-based Wi-Fi fingerprinting location sensing.

Science.gov (United States)

Sun, Yongliang; Xu, Yubin; Li, Cheng; Ma, Lin

2013-11-13

A Kalman/map filtering (KMF)-aided fast normalized cross correlation (FNCC)-based Wi-Fi fingerprinting location sensing system is proposed in this paper. Compared with conventional neighbor selection algorithms that calculate localization results with received signal strength (RSS) mean samples, the proposed FNCC algorithm makes use of all the on-line RSS samples and reference point RSS variations to achieve higher fingerprinting accuracy. The FNCC computes efficiently while maintaining the same accuracy as the basic normalized cross correlation. Additionally, a KMF is also proposed to process fingerprinting localization results. It employs a new map matching algorithm to nonlinearize the linear location prediction process of Kalman filtering (KF) that takes advantage of spatial proximities of consecutive localization results. With a calibration model integrated into an indoor map, the map matching algorithm corrects unreasonable prediction locations of the KF according to the building interior structure. Thus, more accurate prediction locations are obtained. Using these locations, the KMF considerably improves fingerprinting algorithm performance. Experimental results demonstrate that the FNCC algorithm with reduced computational complexity outperforms other neighbor selection algorithms and the KMF effectively improves location sensing accuracy by using indoor map information and spatial proximities of consecutive localization results.

Phenolic Profiling and Antioxidant Capacity of Eugenia uniflora L. (Pitanga) Samples Collected in Different Uruguayan Locations.

Science.gov (United States)

Migues, Ignacio; Baenas, Nieves; Gironés-Vilaplana, Amadeo; Cesio, María Verónica; Heinzen, Horacio; Moreno, Diego A

2018-04-24

The use of nutrient-rich foods to enhance the wellness, health and lifestyle habits of consumers is globally encouraged. Native fruits are of great interest as they are grown and consumed locally and take part of the ethnobotanic knowledge of the population. Pitanga is an example of a native fruit from Uruguay, consumed as a jelly or an alcoholic beverage. Pitanga has a red-violet pigmentation, which is a common trait for foods that are a good source of antioxidants. Hence, fruits from different Uruguayan regions were analyzed via miniaturized sample preparation method, HPLC-DAD-ESI/MS n and RP-HPLC-DAD techniques to identify and quantify phenolic compounds, respectively. The antioxidant capacity was evaluated via DPPH and ORAC (Oxygen Radical Absorbance Capacity) assays. A multivariate linear regression was applied to correlate the observed antioxidant capacity with the phenolic content. Furthermore, Principal Components Analysis was performed to highlight characteristics between the various samples studied. The main results indicated differences between northern and southern Uruguayan samples. Delphinidin-3-hexoside was present in southern samples (mean of 293.16 µmol/100 g dry weight (DW)) and absent in the sample collected in the north (sample 3). All the samples contain high levels of cyanidin-3-hexoside, but a noticeable difference was found between the northern sample (150.45 µmol/100 g DW) and the southern sample (1121.98 µmol/100 g DW). The antioxidant capacity (mean ORAC of 56370 µmol Trolox ® /100 g DW) were high in all the samples compared to the Food and Drug Administration (FDA) database of similar berry-fruits. The results of this study highlight the nutraceutical value of a native fruit that has not been exploited until now.

Phenolic Profiling and Antioxidant Capacity of Eugenia uniflora L. (Pitanga Samples Collected in Different Uruguayan Locations

Directory of Open Access Journals (Sweden)

Ignacio Migues

2018-04-01

Full Text Available The use of nutrient-rich foods to enhance the wellness, health and lifestyle habits of consumers is globally encouraged. Native fruits are of great interest as they are grown and consumed locally and take part of the ethnobotanic knowledge of the population. Pitanga is an example of a native fruit from Uruguay, consumed as a jelly or an alcoholic beverage. Pitanga has a red-violet pigmentation, which is a common trait for foods that are a good source of antioxidants. Hence, fruits from different Uruguayan regions were analyzed via miniaturized sample preparation method, HPLC-DAD-ESI/MSn and RP-HPLC-DAD techniques to identify and quantify phenolic compounds, respectively. The antioxidant capacity was evaluated via DPPH and ORAC (Oxygen Radical Absorbance Capacity assays. A multivariate linear regression was applied to correlate the observed antioxidant capacity with the phenolic content. Furthermore, Principal Components Analysis was performed to highlight characteristics between the various samples studied. The main results indicated differences between northern and southern Uruguayan samples. Delphinidin-3-hexoside was present in southern samples (mean of 293.16 µmol/100 g dry weight (DW and absent in the sample collected in the north (sample 3. All the samples contain high levels of cyanidin-3-hexoside, but a noticeable difference was found between the northern sample (150.45 µmol/100 g DW and the southern sample (1121.98 µmol/100 g DW. The antioxidant capacity (mean ORAC of 56370 µmol Trolox®/100 g DW were high in all the samples compared to the Food and Drug Administration (FDA database of similar berry-fruits. The results of this study highlight the nutraceutical value of a native fruit that has not been exploited until now.

Sampling and analysis plan for sludge located in fuel storage canisters of the 105-K West basin

International Nuclear Information System (INIS)

Baker, R.B.

1997-01-01

This Sampling and Analysis Plan (SAP) provides direction for the first sampling of sludge from the K West Basin spent fuel canisters. The specially developed sampling equipment removes representative samples of sludge while maintaining the radioactive sample underwater in the basin pool (equipment is described in WHC-SD-SNF-SDD-004). Included are the basic background logic for sample selection, the overall laboratory analyses required and the laboratory reporting required. These are based on requirements put forth in the data quality objectives (WHC-SD-SNF-DQO-012) established for this sampling and characterization activity

Methodologies to assess PWSCC susceptibility of primary component Alloy 600 locations in pressurized water reactors

International Nuclear Information System (INIS)

Rao, G.V.

1993-01-01

Methodologies to assess susceptibility to Primary Water Stress Corrosion Cracking (PWSCC) of Alloy 600 component locations in the Primary System of Pressurized Water Reactors are presented. The assessment methodologies are presented. The assessment methodologies are based on Relative Susceptibility Index (RSI) and Cumulative Susceptibility Index (CSI) models utilizing key contributing parameters such as service and residual stresses, yield strength, service temperature, material condition and microstructure, and the accumulated service time. To aid in the development of future inspection plans, a method of ranking of the assessed susceptibilities by 'bench marking' with respect to the susceptibility of a reference location of known PWSCC history of a reference location of known PWSCC history is presented. Means of utilizing the susceptibility ranking results in developing a prioritized inspection plan are discussed. A follow-up investigative plan to the initial inspection is proposed, which includes identification of critical sampling locations, sample extraction, sample investigations and testing to ensure that the potentially highest susceptibility locations are free from near term PWSCC and, further, to provide a basis for established schedules for future inspections. Finally, parametric considerations of the contributing factor are presented to help the utility choose suitable option to mitigate the PWSCC issue while minimizing the impact on continued service

An R package for spatial coverage sampling and random sampling from compact geographical strata by k-means

NARCIS (Netherlands)

Walvoort, D.J.J.; Brus, D.J.; Gruijter, de J.J.

2010-01-01

Both for mapping and for estimating spatial means of an environmental variable, the accuracy of the result will usually be increased by dispersing the sample locations so that they cover the study area as uniformly as possible. We developed a new R package for designing spatial coverage samples for

Nature and location of quantum information

International Nuclear Information System (INIS)

Griffiths, Robert B.

2002-01-01

Quantum information is defined by applying the concepts of ordinary (Shannon) information theory to a quantum sample space consisting of a single framework or consistent family. A classical analogy for a spin-half particle and other arguments show that the infinite amount of information needed to specify a precise vector in its Hilbert space is not a measure of the information carried by a quantum entity with a d-dimensional Hilbert space; the latter is, instead, bounded by log 2 d bits (one bit per qubit). The two bits of information transmitted in dense coding are located not in one but in the correlation between two qubits, consistent with this bound. A quantum channel can be thought of as a structure or collection of frameworks, and the physical location of the information in the individual frameworks can be used to identify the location of the channel. Analysis of a quantum circuit used as a model of teleportation shows that the location of the channel depends upon which structure is employed; for ordinary teleportation it is not (contrary to Deutsch and Hayden) present in the two bits resulting from the Bell-basis measurement, but in correlations of these with a distant qubit. In neither teleportation nor dense coding does information travel backwards in time, nor is it transmitted by nonlocal (superluminal) influences. It is (tentatively) proposed that all aspects of quantum information can in principle be understood in terms of the (basically classical) behavior of information in a particular framework, along with the framework dependence of this information

Lost in Location

DEFF Research Database (Denmark)

Hansen, Lone Koefoed

2009-01-01

traversed. While becoming destination aware, the individual loses her location awareness. The article proposes that the reason people get lost when using sat-nav is due to a wrong location-performative paradigm. As an alternative, the article introduces and analyzes two performance-related examples...... that illustrate an alternative location-performative paradigm: Meredith Warner's Lost/Found knitting series and Etter and Schecht's Melodious Walkabout. In both examples, the artist's hand becomes the intermediary between alien and location. Thus, by exploring how wayfinding can be a poetically situated...... performance, the article examines how the growing locative media industry can learn from the location-aware performative strategies employed by artists who create situated and urban performances for the curious participant. The academic frames employed in the analysis draw on psychogeography, site...

Protein (multi-)location prediction: using location inter-dependencies in a probabilistic framework

Science.gov (United States)

2014-01-01

Motivation Knowing the location of a protein within the cell is important for understanding its function, role in biological processes, and potential use as a drug target. Much progress has been made in developing computational methods that predict single locations for proteins. Most such methods are based on the over-simplifying assumption that proteins localize to a single location. However, it has been shown that proteins localize to multiple locations. While a few recent systems attempt to predict multiple locations of proteins, their performance leaves much room for improvement. Moreover, they typically treat locations as independent and do not attempt to utilize possible inter-dependencies among locations. Our hypothesis is that directly incorporating inter-dependencies among locations into both the classifier-learning and the prediction process can improve location prediction performance. Results We present a new method and a preliminary system we have developed that directly incorporates inter-dependencies among locations into the location-prediction process of multiply-localized proteins. Our method is based on a collection of Bayesian network classifiers, where each classifier is used to predict a single location. Learning the structure of each Bayesian network classifier takes into account inter-dependencies among locations, and the prediction process uses estimates involving multiple locations. We evaluate our system on a dataset of single- and multi-localized proteins (the most comprehensive protein multi-localization dataset currently available, derived from the DBMLoc dataset). Our results, obtained by incorporating inter-dependencies, are significantly higher than those obtained by classifiers that do not use inter-dependencies. The performance of our system on multi-localized proteins is comparable to a top performing system (YLoc+), without being restricted only to location-combinations present in the training set. PMID:24646119

Protein (multi-)location prediction: using location inter-dependencies in a probabilistic framework.

Science.gov (United States)

Simha, Ramanuja; Shatkay, Hagit

2014-03-19

Knowing the location of a protein within the cell is important for understanding its function, role in biological processes, and potential use as a drug target. Much progress has been made in developing computational methods that predict single locations for proteins. Most such methods are based on the over-simplifying assumption that proteins localize to a single location. However, it has been shown that proteins localize to multiple locations. While a few recent systems attempt to predict multiple locations of proteins, their performance leaves much room for improvement. Moreover, they typically treat locations as independent and do not attempt to utilize possible inter-dependencies among locations. Our hypothesis is that directly incorporating inter-dependencies among locations into both the classifier-learning and the prediction process can improve location prediction performance. We present a new method and a preliminary system we have developed that directly incorporates inter-dependencies among locations into the location-prediction process of multiply-localized proteins. Our method is based on a collection of Bayesian network classifiers, where each classifier is used to predict a single location. Learning the structure of each Bayesian network classifier takes into account inter-dependencies among locations, and the prediction process uses estimates involving multiple locations. We evaluate our system on a dataset of single- and multi-localized proteins (the most comprehensive protein multi-localization dataset currently available, derived from the DBMLoc dataset). Our results, obtained by incorporating inter-dependencies, are significantly higher than those obtained by classifiers that do not use inter-dependencies. The performance of our system on multi-localized proteins is comparable to a top performing system (YLoc+), without being restricted only to location-combinations present in the training set.

Gender, Location and Rural-Urban Differences in the Goal ...

African Journals Online (AJOL)

The need to identify critical factors necessary to improve the mandate attainment of the National Youth Service Corps (NYSC) Scheme informed this study on gender, location and rural-urban differences in the goal attainment of NYSC in South West Nigeria. Using a multistage sampling procedure, 120 outgoing youth corps ...

Medical specialists' choice of location: the role of geographical attachment in Norway.

Science.gov (United States)

Kristiansen, I S; Førde, O H

1992-01-01

The relation between current place of work (area of the country) and factors that might possibly represent doctors geographical attachments was studied in a sample of 322 Norwegian medical specialists. Location of hospital residency, age and geographical origin of spouse were associated with current location. Geographical attachment seems to influence doctors' locational choices from start of medical school until the end of their residency. The probability that a doctor shall locate in peripheral areas may increase from less than 10% to more than 50% if the doctor has the residency training in the periphery. Hence, favoring entrance to medical schools of students from the underserved areas, and location of graduate and postgraduate medical training in the underserved areas, as far as it is feasible while still maintaining medical standards, is suggested by the study.

Hanford site environmental surveillance master sampling schedule

International Nuclear Information System (INIS)

Bisping, L.E.

1998-01-01

Environmental surveillance of the Hanford Site and surrounding areas is conducted by the Pacific Northwest National Laboratory (PNNL) for the U.S. Department of Energy (DOE). Sampling is conducted to evaluate levels of radioactive and nonradioactive pollutants in the Hanford environs, as required in DOE Order 5400.1 open-quotes General Environmental Protection Program,close quotes and DOE Order 5400.5, open-quotes Radiation Protection of the Public and the Environment.close quotes The sampling methods are described in the Environmental Monitoring Plan, United States Department of Energy, Richland Operations Office, DOE/RL91-50, Rev. 2, U.S. Department of Energy, Richland, Washington. This document contains the 1998 schedules for routine collection of samples for the Surface Environmental Surveillance Project (SESP) and Drinking Water Monitoring Project. Each section of this document describes the planned sampling schedule for a specific media (air, surface water, biota, soil and vegetation, sediment, and external radiation). Each section includes the sample location, sample type, and analyses to be performed on the sample. In some cases, samples are scheduled on a rotating basis and may not be planned for 1998 in which case the anticipated year for collection is provided. In addition, a map is included for each media showing sample locations

Quarter Dates Location(s) Purpose Transportation and Travel ...

International Development Research Centre (IDRC) Digital Library (Canada)

IDRC CRDI

Dates. Location(s). Purpose. Transportation and Travel. Accommodation,. Meals and Other. Hospitality. Total. Expenses. Quarter 1. May 15. Ottawa, ON. Meetings. May 20 to 21. Washington DC. Conference. 11,364.93. 3,274.71. 53.50. 14,693.14. May 5 to June 5. Kenya and England. Meetings. June 18 to 21. Winnipeg, MB.

i-Locate - Indoor/Outdoor location and Asset Management through Open Data

Directory of Open Access Journals (Sweden)

Claudio Eccher

2015-02-01

Full Text Available Studi recenti hanno evidenziato che, in media, trascorriamo circa il 90% del nostro tempo in ambienti chiusi e, spesso, non familiari. L’esigenza di localizzare/guidare persone o ogg etti in spazi sia esterni che interni (senza discontinuità tra esterno ed interno darà origine ad una serie di nuovi servizi di tipo LBS (Location-Based Services che potranno avere anche una notevole rilevanza economica. i-locate (Indoor / outdoor location and Asset Management Through open geodata is a project that aims to develop a set of tools and services based on geo location technologies based on open data for the location and management of objects in indoor and outdoor spaces. The tools are intended both to citizens who use their smartphones to access services, aids to navigation from the front door to internal destinations to buildings (public office, clinic, shop, etc.. Obtaining any information available to support (code , unforeseen changes in the path, suggestions, etc., and professionals for specific activities that require the location of people, equipment, etc. i-locate to an intense use of GIS technologies for navigation and tracking "indoor" (indoor GIS, 3D GIS, to locate people (eg. Alzheimer's patients and their movements in areas not suited (geofencing to identify and track objects / portable equipment for their location, management and maintenance.

i-Locate - Indoor/Outdoor location and Asset Management through Open Data

Directory of Open Access Journals (Sweden)

Claudio Eccher

2015-02-01

Full Text Available Studi recenti hanno evidenziato che, in media, trascorriamo circa il 90% del nostro tempo in ambienti chiusi e, spesso, non familiari. L’esigenza di localizzare/guidare persone o ogg etti in spazi sia esterni che interni (senza discontinuità tra esterno ed interno darà origine ad una serie di nuovi servizi di tipo LBS (Location-Based Services che potranno avere anche una notevole rilevanza economica.i-locate (Indoor / outdoor location and Asset Management Through open geodata is a project that aims to develop a set of tools and services based on geo location technologies based on open data for the location and management of objects in indoor and outdoor spaces. The tools are intended both to citizens who use their smartphones to access services, aids to navigation from the front door to internal destinations to buildings (public office, clinic, shop, etc.. Obtaining any information available to support (code , unforeseen changes in the path, suggestions, etc., and professionals for specific activities that require the location of people, equipment, etc. i-locate to an intense use of GIS technologies for navigation and tracking "indoor" (indoor GIS, 3D GIS, to locate people (eg. Alzheimer's patients and their movements in areas not suited (geofencing to identify and track objects / portable equipment for their location, management and maintenance.

30 CFR 75.336 - Sampling and monitoring requirements.

Science.gov (United States)

2010-07-01

... concentration of other sampling locations in the sealed area and other required information. Before miners... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Sampling and monitoring requirements. 75.336... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.336 Sampling and...

Location Systems An Introduction to the Technology Behind Location Awareness

CERN Document Server

LaMarca, Anthony

2008-01-01

Advances in electronic location technology and the coming of age of mobile computing have opened the door for location-aware applications to permeate all aspects of everyday life. Location is at the core of a large number of high-value applications ranging from the life-and-death context of emergency response to serendipitous social meet-ups. For example, the market for GPS products and services alone is expected to grow to US200 billion by 2015. Unfortunately, there is no single location technology that is good for every situation and exhibits high accuracy, low cost, and universal coverage.

Historical review of long-term soil sampling for environmental surveillance at the Hanford Site and vicinity

Energy Technology Data Exchange (ETDEWEB)

Price, K.R.; Rickard, W.H.

1997-08-01

Soil samples have been collected routinely from the environs of the Hanford Site and analyzed since 1971. Correct interpretation of results depends on samples being collected from the same locations, the locations remaining relatively undisturbed, and collection and analytical procedures remaining the same or being equivalent. Historical files, documents, and annual environmental reports were reviewed to evaluate these factors. It was determined that 20 soil sampling locations, 11 onsite and 9 offsite, were established between 1971 and 1977 and represent long-term sampling locations. Sample collection and analytical procedures have remained essentially the same since 1971. The physical ecological attributes of each long-term soil sampling location were evaluated. During the review of historical records, a few results for 1970, 1971, and 1972 were noted as previously unreported in annual or special reports. These results are included in Appendix A. To complete the record, results previously reported in annual environmental reports are given in Appendix B. Global Positioning System (GPS) reading for 20 long-term soil sampling locations are provided in Appendix C.

Historical review of long-term soil sampling for environmental surveillance at the Hanford Site and vicinity

International Nuclear Information System (INIS)

Price, K.R.; Rickard, W.H.

1997-08-01

Soil samples have been collected routinely from the environs of the Hanford Site and analyzed since 1971. Correct interpretation of results depends on samples being collected from the same locations, the locations remaining relatively undisturbed, and collection and analytical procedures remaining the same or being equivalent. Historical files, documents, and annual environmental reports were reviewed to evaluate these factors. It was determined that 20 soil sampling locations, 11 onsite and 9 offsite, were established between 1971 and 1977 and represent long-term sampling locations. Sample collection and analytical procedures have remained essentially the same since 1971. The physical ecological attributes of each long-term soil sampling location were evaluated. During the review of historical records, a few results for 1970, 1971, and 1972 were noted as previously unreported in annual or special reports. These results are included in Appendix A. To complete the record, results previously reported in annual environmental reports are given in Appendix B. Global Positioning System (GPS) reading for 20 long-term soil sampling locations are provided in Appendix C

Source apportionment and location by selective wind sampling and Positive Matrix Factorization.

Science.gov (United States)

Venturini, Elisa; Vassura, Ivano; Raffo, Simona; Ferroni, Laura; Bernardi, Elena; Passarini, Fabrizio

2014-10-01

In order to determine the pollution sources in a suburban area and identify the main direction of their origin, PM2.5 was collected with samplers coupled with a wind select sensor and then subjected to Positive Matrix Factorization (PMF) analysis. In each sample, soluble ions, organic carbon, elemental carbon, levoglucosan, metals, and Polycyclic Aromatic Hydrocarbons (PAHs) were determined. PMF results identified six main sources affecting the area: natural gas home appliances, motor vehicles, regional transport, biomass combustion, manufacturing activities, and secondary aerosol. The connection of factor temporal trends with other parameters (i.e., temperature, PM2.5 concentration, and photochemical processes) confirms factor attributions. PMF analysis indicated that the main source of PM2.5 in the area is secondary aerosol. This should be mainly due to regional contributions, owing to both the secondary nature of the source itself and the higher concentration registered in inland air masses. The motor vehicle emission source contribution is also important. This source likely has a prevalent local origin. The most toxic determined components, i.e., PAHs, Cd, Pb, and Ni, are mainly due to vehicular traffic. Even if this is not the main source in the study area, it is the one of greatest concern. The application of PMF analysis to PM2.5 collected with this new sampling technique made it possible to obtain more detailed results on the sources affecting the area compared to a classical PMF analysis.

A sampling strategy for estimating plot average annual fluxes of chemical elements from forest soils

NARCIS (Netherlands)

Brus, D.J.; Gruijter, de J.J.; Vries, de W.

2010-01-01

A sampling strategy for estimating spatially averaged annual element leaching fluxes from forest soils is presented and tested in three Dutch forest monitoring plots. In this method sampling locations and times (days) are selected by probability sampling. Sampling locations were selected by

A Multi-Sample Cs-Sputter Negative Ion Source

International Nuclear Information System (INIS)

Alton, G.D.; Ball, J.A.; Bao, Y.; Cui, B.; Reed, C.A.; Williams, C.

1998-01-01

A multi-sample Cs sputter negative-ion source, equipped with a conical-geometry, W-surface-ionizer has been designed and fabricated that permits sample changes without disruption of on-line accelerator operation. Sample changing is effected by actuating an electro-pneumatic control system located at ground potential that drives an air-motor-driven sample-indexing-system mounted at high voltage; this arrangement avoids complications associated with indexing mechanisms that rely on electronic power-supplies located at high potential. In-beam targets are identified by LED indicator lights derived from a fiber-optic, Gray-code target-position sensor. Aspects of the overall source design and details of the indexing mechanism along with operational parameters, ion optics. intensities, and typical emittances for a variety of negative-ion species will be presented in this report

A Multi-Sample Cs-Sputter Negative Ion Source

Energy Technology Data Exchange (ETDEWEB)

Alton, G.D.; Ball, J.A.; Bao, Y.; Cui, B.; Reed, C.A.; Williams, C.

1998-10-05

A multi-sample Cs sputter negative-ion source, equipped with a conical-geometry, W-surface-ionizer has been designed and fabricated that permits sample changes without disruption of on-line accelerator operation. Sample changing is effected by actuating an electro-pneumatic control system located at ground potential that drives an air-motor-driven sample-indexing-system mounted at high voltage; this arrangement avoids complications associated with indexing mechanisms that rely on electronic power-supplies located at high potential. In-beam targets are identified by LED indicator lights derived from a fiber-optic, Gray-code target-position sensor. Aspects of the overall source design and details of the indexing mechanism along with operational parameters, ion optics. intensities, and typical emittances for a variety of negative-ion species will be presented in this report.

The Improved Locating Algorithm of Particle Filter Based on ROS Robot

Science.gov (United States)

Fang, Xun; Fu, Xiaoyang; Sun, Ming

2018-03-01

This paperanalyzes basic theory and primary algorithm of the real-time locating system and SLAM technology based on ROS system Robot. It proposes improved locating algorithm of particle filter effectively reduces the matching time of laser radar and map, additional ultra-wideband technology directly accelerates the global efficiency of FastSLAM algorithm, which no longer needs searching on the global map. Meanwhile, the re-sampling has been largely reduced about 5/6 that directly cancels the matching behavior on Roboticsalgorithm.

Hanford Site Environmental Surveillance Master Sampling Schedule for Calendar Year 2010

Energy Technology Data Exchange (ETDEWEB)

Bisping, Lynn E.

2010-01-08

Environmental surveillance of the Hanford Site and surrounding areas is conducted by Pacific Northwest National Laboratory for the U.S. Department of Energy (DOE). Sampling is conducted to evaluate levels of radioactive and nonradioactive pollutants in the Hanford Site environs per regulatory requirements. This document contains the calendar year 2010 schedule for the routine collection of samples for the Surface Environmental Surveillance Project and the Drinking Water Monitoring Project. Each section includes sampling locations, sampling frequencies, sample types, and analyses to be performed. In some cases, samples are scheduled on a rotating basis. If a sample will not be collected in 2010, the anticipated year for collection is provided. Maps showing approximate sampling locations are included for media scheduled for collection in 2010.

Penile vascular diagnostic categorization using penile duplex Doppler ultrasound: Differences in vascular hemodynamics parameters by differences in anatomic sampling location

Directory of Open Access Journals (Sweden)

Fabio Pezzoni

2016-10-01

Full Text Available Objectives. In 2013 the International Society for Sexual Medicine(ISSM published the guidelines regarding the standard operating procedure (SOP for penile duplex Doppler ultrasound (PDDU. Although ISSM-SOP have given important strides in reducing interobserver variability in PDDU by procedural protocol and parameters these guidelines do not address the anatomic location along the penis at which hemodynamic measurements have to be done. In our opinion a “double sampling” may be interesting to detect the arteriogenic or venogenic nature of the erectile dysfunction (ED. In particular sampling measurements at the “crus” (at the level of the peno-scrotal junction may be significative for detection of veno-occlusive dysfunction (VOD,whereas an evaluation at “mid penis” (1/2 distance between peno-scrotal junction and coronal sulcus, may be useful to diagnose an arterial insufficiency (AI. Material and Methods. We evalued 90 men, mean age 56.3, affected with ED of medium degree, responder to PDE5-I that urdergone to PDDU and also responder after pharmacologic intracavernosal injection (PIIof prostaglandin E1 20 mcg, with rigid erection and normal maintenance. We moreover evalued 90 men in youthful age (mean 35.2, in absence of vascular risk factors, no responder to PDE5-I that undergone to PDDU by PII at high dosage (bimix: prostaglandin E1 20 mcg, papaverine 20 mg. Results. In the first pool the sampling at “mid penis” resulted significative for arterial insuffciency (AI in 81% (73, in presence of normal or borderline end diastolic velocity (EDV. Sampling at the “crus” resulted negative for VOD in 90% (81. In the second pool, 66.6% (60 resulted responder with rigid erection and normal maintenance in presence of normal hemodynamic parameters: peak systolic velocity (PSV and end diastolic velocity (EDV both at the “crus” and at “mid penis” sampling. 33.4% (30 responded with a semirigid erection and manifested a constant

Tremor Source Location at Okmok Volcano

Science.gov (United States)

Reyes, C. G.; McNutt, S. R.

2007-12-01

Initial results using an amplitude-based tremor location program have located several active tremor episodes under Cone A, a vent within Okmok volcano's 10 km caldera. Okmok is an andesite volcano occupying the north-eastern half of Umnak Island, in the Aleutian islands. Okmok is defined by a ~2000 y.b.p. caldera that contains multiple cinder cones. Cone A, the youngest of these, extruded lava in 1997 covering the caldera floor. Since April 2003, continuous seismic data have been recorded from eight vertical short-period stations (L4-C's) installed at distances from Cone A ranging from 2 km to 31 km. In 2004 four additional 3- component broadband stations were added, co-located with continuous GPS stations. InSAR and GPS measurements of post-eruption deformation show that Okmok experienced several periods of rapid inflation (Mann and Freymueller, 2002), from the center of the 10 km diameter caldera. While there are few locatable VT earthquakes, there has been nearly continuous low-level tremor with stronger amplitude bursts occurring at variable rates and durations. The character of occurrence remained relatively constant over the course of days to weeks until the signal ceased in mid 2005. Within any day, tremor behavior remains fairly consistent, with bursts closely resembling each other, suggesting a single main process or source location. The tremor is composed of irregular waves with a broad range of frequencies, though most energy resides between ~2 Hz and 6 Hz. Attempts to locate the tremor using traditional arrival time methods fail because the signal is emergent, with envelopes too ragged to correlate on time scales that hold much hope for a location. Instead, focus was shifted to the amplitude ratios at various stations. Candidates for the tremor source include the center of inflation and Cone A, 3 km to the south-west. For all dates on record, data were band pass filtered between 1 and 5 Hz, then evaluated in 20.48 second windows (N=2048, sampling rate

LocateP: Genome-scale subcellular-location predictor for bacterial proteins

Directory of Open Access Journals (Sweden)

Zhou Miaomiao

2008-03-01

Full Text Available Abstract Background In the past decades, various protein subcellular-location (SCL predictors have been developed. Most of these predictors, like TMHMM 2.0, SignalP 3.0, PrediSi and Phobius, aim at the identification of one or a few SCLs, whereas others such as CELLO and Psortb.v.2.0 aim at a broader classification. Although these tools and pipelines can achieve a high precision in the accurate prediction of signal peptides and transmembrane helices, they have a much lower accuracy when other sequence characteristics are concerned. For instance, it proved notoriously difficult to identify the fate of proteins carrying a putative type I signal peptidase (SPIase cleavage site, as many of those proteins are retained in the cell membrane as N-terminally anchored membrane proteins. Moreover, most of the SCL classifiers are based on the classification of the Swiss-Prot database and consequently inherited the inconsistency of that SCL classification. As accurate and detailed SCL prediction on a genome scale is highly desired by experimental researchers, we decided to construct a new SCL prediction pipeline: LocateP. Results LocateP combines many of the existing high-precision SCL identifiers with our own newly developed identifiers for specific SCLs. The LocateP pipeline was designed such that it mimics protein targeting and secretion processes. It distinguishes 7 different SCLs within Gram-positive bacteria: intracellular, multi-transmembrane, N-terminally membrane anchored, C-terminally membrane anchored, lipid-anchored, LPxTG-type cell-wall anchored, and secreted/released proteins. Moreover, it distinguishes pathways for Sec- or Tat-dependent secretion and alternative secretion of bacteriocin-like proteins. The pipeline was tested on data sets extracted from literature, including experimental proteomics studies. The tests showed that LocateP performs as well as, or even slightly better than other SCL predictors for some locations and outperforms

The variance quadtree algorithm: use for spatial sampling design

NARCIS (Netherlands)

Minasny, B.; McBratney, A.B.; Walvoort, D.J.J.

2007-01-01

Spatial sampling schemes are mainly developed to determine sampling locations that can cover the variation of environmental properties in the area of interest. Here we proposed the variance quadtree algorithm for sampling in an area with prior information represented as ancillary or secondary

Quarterly sampling of the wetlands along the old F Area effluent ditch: August 1994

International Nuclear Information System (INIS)

Cummins, C.L.; Dixon, K.L.

1994-08-01

In August 1994, well point water and near-surface water samples were collected to characterize tritium and volatile organic compounds (VOC) in the wetlands along the old F-Area effluent ditch south of 643-E (old burial ground). The August sampling event was the third in a series of eight events. Groundwater flow paths suggest that compounds detected in water table wells around 643-E migrate towards the old F-Area effluent ditch and Fourmile Branch. Recent analytical results from well point and near-surface water sampling in the wetlands that comprise the old F-Area effluent ditch have shown that tritium and small quantities of VOCs are outcropping in the area. For this study, seven locations along the old F-Area effluent ditch were selected to be sampled. Well point samples were collected from all seven locations and near-surface water samples were collected at four locations. A secondary objective of this project was to compare VOC concentrations between the well points installed to depths of 6 to 8 ft and the near-surface water sampling buckets installed to depths of 1 to 2 ft. Based on differences in tritium concentrations at each location, it was determined that the sampling devices intercepted different groundwater flow paths. This negated direct comparison of analytical results between devices. However, when VOC concentrations measured at each well point and bucket location were normalized, based on the percent differences observed in tritium concentrations at that location, the resulting well point and bucket VOC concentrations were comparable in most cases. These results are consistent with the results from the three previous sampling events, and suggest that volatilization losses of VOCs from the buckets may be negligible. Since the results from the two sampling methodologies are not directly comparable, further sampling of the buckets is not planned

Store Location in Shopping Centers: Theory & Estimates

OpenAIRE

Kerry D. Vandell; Charles C. Carter

2000-01-01

This paper develops a formal theory of store location within shopping centers based on bid rent theory. The bid rent model is fully speci?ed and solved with the objective function of pro?t maximization in the presence of comparative, multipurpose and impulse shopping behavior. Several hypotheses result about the optimal relationships between store types, sizes, rents, sales, and distances from the mall center. The hypotheses are tested and con?rmed using data from a sample of 689 leases in ei...

KCBX Petroleum Coke Storage Pile Sampling Logbook and Photos

Science.gov (United States)

This documentation of KCBX's petcoke sampling locations and methods demonstrates adherence to the pet coke sampling plan previously submitted and approved by EPA, at both North Terminal and South Terminal stockpiles.

An Indoor Location-Based Control System Using Bluetooth Beacons for IoT Systems.

Science.gov (United States)

Huh, Jun-Ho; Seo, Kyungryong

2017-12-19

The indoor location-based control system estimates the indoor position of a user to provide the service he/she requires. The major elements involved in the system are the localization server, service-provision client, user application positioning technology. The localization server controls access of terminal devices (e.g., Smart Phones and other wireless devices) to determine their locations within a specified space first and then the service-provision client initiates required services such as indoor navigation and monitoring/surveillance. The user application provides necessary data to let the server to localize the devices or allow the user to receive various services from the client. The major technological elements involved in this system are indoor space partition method, Bluetooth 4.0, RSSI (Received Signal Strength Indication) and trilateration. The system also employs the BLE communication technology when determining the position of the user in an indoor space. The position information obtained is then used to control a specific device(s). These technologies are fundamental in achieving a "Smart Living". An indoor location-based control system that provides services by estimating user's indoor locations has been implemented in this study (First scenario). The algorithm introduced in this study (Second scenario) is effective in extracting valid samples from the RSSI dataset but has it has some drawbacks as well. Although we used a range-average algorithm that measures the shortest distance, there are some limitations because the measurement results depend on the sample size and the sample efficiency depends on sampling speeds and environmental changes. However, the Bluetooth system can be implemented at a relatively low cost so that once the problem of precision is solved, it can be applied to various fields.

An Indoor Location-Based Control System Using Bluetooth Beacons for IoT Systems

Directory of Open Access Journals (Sweden)

Jun-Ho Huh

2017-12-01

Full Text Available The indoor location-based control system estimates the indoor position of a user to provide the service he/she requires. The major elements involved in the system are the localization server, service-provision client, user application positioning technology. The localization server controls access of terminal devices (e.g., Smart Phones and other wireless devices to determine their locations within a specified space first and then the service-provision client initiates required services such as indoor navigation and monitoring/surveillance. The user application provides necessary data to let the server to localize the devices or allow the user to receive various services from the client. The major technological elements involved in this system are indoor space partition method, Bluetooth 4.0, RSSI (Received Signal Strength Indication and trilateration. The system also employs the BLE communication technology when determining the position of the user in an indoor space. The position information obtained is then used to control a specific device(s. These technologies are fundamental in achieving a “Smart Living”. An indoor location-based control system that provides services by estimating user’s indoor locations has been implemented in this study (First scenario. The algorithm introduced in this study (Second scenario is effective in extracting valid samples from the RSSI dataset but has it has some drawbacks as well. Although we used a range-average algorithm that measures the shortest distance, there are some limitations because the measurement results depend on the sample size and the sample efficiency depends on sampling speeds and environmental changes. However, the Bluetooth system can be implemented at a relatively low cost so that once the problem of precision is solved, it can be applied to various fields.

Hanford Site Environmental Surveillance Master Sampling Schedule for Calendar Year 2009

Energy Technology Data Exchange (ETDEWEB)

Bisping, Lynn E.

2009-01-20

Environmental surveillance of the Hanford Site and surrounding areas is conducted by the Pacific Northwest National Laboratory for the U.S. Department of Energy. Sampling is conducted to evaluate levels of radioactive and nonradioactive pollutants in the Hanford environs, as required in DOE Order 450.1 and DOE Order 5400.5. This document contains the calendar year 2009 schedule for the routine collection of samples for the Surface Environmental Surveillance Project and Drinking Water Monitoring Project. Each section includes sampling locations, sampling frequencies, sample types, and analyses to be performed. In some cases, samples are scheduled on a rotating basis. If a sample will not be collected in 2009, the anticipated year for collection is provided. Maps showing approximate sampling locations are included for media scheduled for collection in 2009.

Mass counting of radioactivity samples

International Nuclear Information System (INIS)

Oesterlin, D.L.; Obrycki, R.F.

1977-01-01

A method and apparatus for concurrently counting a plurality of radioactive samples is claimed. The position sensitive circuitry of a scintillation camera is employed to sort electrical pulses resulting from scintillations according to the geometrical locations of scintillations causing those pulses. A scintillation means, in the form of a scintillating crystal material or a liquid scintillator, is positioned proximate to an array of radioactive samples. Improvement in the accuracy of pulse classification may be obtained by employing collimating means. If a plurality of scintillation crystals are employed to measure the iodine-125 content of samples, a method and means are provided for correcting for variations in crystal light transmission properties, sample volume, and sample container radiation absorption. 2 claims, 7 drawing figures

Automated seismic waveform location using Multichannel Coherency Migration (MCM)-I. Theory

Science.gov (United States)

Shi, Peidong; Angus, Doug; Rost, Sebastian; Nowacki, Andy; Yuan, Sanyi

2018-03-01

With the proliferation of dense seismic networks sampling the full seismic wavefield, recorded seismic data volumes are getting bigger and automated analysis tools to locate seismic events are essential. Here, we propose a novel Multichannel Coherency Migration (MCM) method to locate earthquakes in continuous seismic data and reveal the location and origin time of seismic events directly from recorded waveforms. By continuously calculating the coherency between waveforms from different receiver pairs, MCM greatly expands the available information which can be used for event location. MCM does not require phase picking or phase identification, which allows fully automated waveform analysis. By migrating the coherency between waveforms, MCM leads to improved source energy focusing. We have tested and compared MCM to other migration-based methods in noise-free and noisy synthetic data. The tests and analysis show that MCM is noise resistant and can achieve more accurate results compared with other migration-based methods. MCM is able to suppress strong interference from other seismic sources occurring at a similar time and location. It can be used with arbitrary 3D velocity models and is able to obtain reasonable location results with smooth but inaccurate velocity models. MCM exhibits excellent location performance and can be easily parallelized giving it large potential to be developed as a real-time location method for very large datasets.

Quantifying geocode location error using GIS methods

Directory of Open Access Journals (Sweden)

Gardner Bennett R

2007-04-01

Full Text Available Abstract Background The Metropolitan Atlanta Congenital Defects Program (MACDP collects maternal address information at the time of delivery for infants and fetuses with birth defects. These addresses have been geocoded by two independent agencies: (1 the Georgia Division of Public Health Office of Health Information and Policy (OHIP and (2 a commercial vendor. Geographic information system (GIS methods were used to quantify uncertainty in the two sets of geocodes using orthoimagery and tax parcel datasets. Methods We sampled 599 infants and fetuses with birth defects delivered during 1994–2002 with maternal residence in either Fulton or Gwinnett County. Tax parcel datasets were obtained from the tax assessor's offices of Fulton and Gwinnett County. High-resolution orthoimagery for these counties was acquired from the U.S. Geological Survey. For each of the 599 addresses we attempted to locate the tax parcel corresponding to the maternal address. If the tax parcel was identified the distance and the angle between the geocode and the residence were calculated. We used simulated data to characterize the impact of geocode location error. In each county 5,000 geocodes were generated and assigned their corresponding Census 2000 tract. Each geocode was then displaced at a random angle by a random distance drawn from the distribution of observed geocode location errors. The census tract of the displaced geocode was determined. We repeated this process 5,000 times and report the percentage of geocodes that resolved into incorrect census tracts. Results Median location error was less than 100 meters for both OHIP and commercial vendor geocodes; the distribution of angles appeared uniform. Median location error was approximately 35% larger in Gwinnett (a suburban county relative to Fulton (a county with urban and suburban areas. Location error occasionally caused the simulated geocodes to be displaced into incorrect census tracts; the median percentage

Detailed characterization of welding fumes in personal exposure samples

International Nuclear Information System (INIS)

Quémerais, B; Mino, James; Amin, M R; Golshahi, H; Izadi, H

2015-01-01

The objective of the project was to develop a method allowing for detailed characterization of welding particles including particle number concentration, size distribution, surface chemistry and chemical composition of individual particles, as well as metal concentration of various welding fumes in personal exposure samples using regular sampling equipment. A sample strategy was developed to evaluate the variation of the collection methods on mass concentration. Samples were collected with various samplers and filters at two different locations using our collection system. The first location was using a robotic welding system while the second was manual welding. Collected samples were analysed for mass concentration using gravimetryand metal concentration using ICP/OES. More advanced analysis was performed on selected filters using X-Ray Photoelectron Spectroscopy to determine surface composition of the particles, and X-Ray Diffraction to determine chemical composition of the fumes. Results showed that the robotic system had a lot of variation in space when the collection system was located close to the weld. Collection efficiency was found to be quite variable depending upon the type of filter. As well, metal concentrations in blank filters were dependent upon the type of filter with MCE presenting with the highest blank values. Results obtained with the XRD and XPS systems showed that it was possible to analyse a small of powdered welding fume sample but results on filters were not conclusive. (paper)

Location-based prospective memory.

Science.gov (United States)

O'Rear, Andrea E; Radvansky, Gabriel A

2018-02-01

This study explores location-based prospective memory. People often have to remember to do things when in a particular location, such as buying tissues the next time they are in the supermarket. For event cognition theory, location is important for structuring events. However, because event cognition has not been used to examine prospective memory, the question remains of how multiple events will influence prospective memory performance. In our experiments, people delivered messages from store to store in a virtual shopping mall as an ongoing task. The prospective tasks were to do certain activities in certain stores. For Experiment 1, each trial involved one prospective memory task to be done in a single location at one of three delays. The virtual environment and location cues were effective for prospective memory, and performance was unaffected by delay. For Experiment 2, each trial involved two prospective memory tasks, given in either one or two instruction locations, and to be done in either one or two store locations. There was improved performance when people received instructions from two locations and did both tasks in one location relative to other combinations. This demonstrates that location-based event structure influences how well people perform on prospective memory tasks.

Influence of motivation, library materials and location on use of ...

African Journals Online (AJOL)

The study investigated the influence of motivation, availability and adequacy of library materials as well as location of library on the use of library by undergraduates in University of Ibadan, Nigeria. The convenience sampling technique was adopted to select only 150 undergraduates while the questionnaire was used as the ...

Guidance for air sampling at nuclear facilities

International Nuclear Information System (INIS)

Breslin, A.J.

1976-11-01

The principal uses of air sampling at nuclear facilities are to monitor general levels of radioactive air contamination, identify sources of air contamination, and evaluate the effectiveness of contaminant control equipment, determine exposures of individual workers, and provide automatic warning of hazardous concentrations of radioactivity. These applications of air sampling are discussed with respect to standards of occupational exposure, instrumentation, sample analysis, sampling protocol, and statistical treatment of concentration data. Emphasis is given to the influence of spacial and temporal variations of radionuclide concentration on the location, duration, and frequency of air sampling

Stream sediment sampling and analysis. Final report

International Nuclear Information System (INIS)

Means, J.L.; Voris, P.V.; Headington, G.L.

1986-04-01

The objectives were to sample and analyze sediments from upstream and downstream locations (relative to the Goodyear Atomic plant site) of three streams for selected pollutants. The three streams sampled were the Scioto River, Big Beaver Creek, and Big Run Creek. Sediment samples were analyzed for EPA's 129 priority pollutants (Clean Water Act) as well as isotopic uranium ( 234 U, 235 U, and 238 U) and technetium-99

Perceptions of clients on awareness and the geographical location of a South African university sexual health clinic.

Science.gov (United States)

Adams, Rukshana; Van Der Heever, Mariana M; Damons, Anneleen

2017-09-27

The Campus Health Service at Stellenbosch University has a sub-division, a sexual health clinic, which provides sexual health services. The clients of the sexual health clinic consist of staff members and students. This article reports on the perceptions of clients that relate to awareness and the geographical location of the clinic. The Campus Health Service at Stellenbosch University's main campus. A descriptive qualitative approach was applied utilising in-depth interviews. A sample of n = 15 was drawn through purposive sampling and data saturation was achieved with the sample. The following themes emerged from the data: location of the clinic, awareness of sexual health services and marketing and advertising. The findings of the study revealed that accessibility of the clinic is influenced by the geographical location of the clinic and that marketing and awareness of services require attention.

Data Validation Package May 2016 Groundwater Sampling at the Lakeview, Oregon, Processing Site August 2016

Energy Technology Data Exchange (ETDEWEB)

Linard, Joshua [USDOE Office of Legacy Management, Washington, DC (United States); Hall, Steve [Navarro Research and Engineering, Inc., Oak Ridge, TN (United States)

2016-08-01

This biennial event includes sampling five groundwater locations (four monitoring wells and one domestic well) at the Lakeview, Oregon, Processing Site. For this event, the domestic well (location 0543) could not be sampled because no one was in residence during the sampling event (Note: notification was provided to the resident prior to the event). Per Appendix A of the Groundwater Compliance Action Plan, sampling is conducted to monitor groundwater quality on a voluntary basis. Sampling and analyses were conducted as specified in the Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated). One duplicate sample was collected from location 0505. Water levels were measured at each sampled monitoring well. The constituents monitored at the Lakeview site are manganese and sulfate. Monitoring locations that exceeded the U.S. Environmental Protection Agency (EPA) Secondary Maximum Contaminant Levels for these constituents are listed in Table 1. Review of time-concentration graphs included in this report indicate that manganese and sulfate concentrations are consistent with historical measurements.

Does Drinking Location Matter? Profiles of Risky Single-Occasion Drinking by Location and Alcohol-Related Harm among Young Men.

Science.gov (United States)

Bähler, Caroline; Dey, Michelle; Dermota, Petra; Foster, Simon; Gmel, Gerhard; Mohler-Kuo, Meichun

2014-01-01

In adolescents and young adults, acute consequences like injuries account for a substantial proportion of alcohol-related harm, especially in risky single-occasion (RSO) drinkers. The primary aim of the study was to characterize different drinking profiles in RSO drinkers according to drinking locations and their relationship to negative, alcohol-related consequences. The sample consisted of 2746 young men from the Cohort Study on Substance Use Risk Factors who had reported drinking six or more drinks on a single-occasion at least monthly over the preceding 12 months. Principal component analysis on the frequency and amount of drinking at 11 different locations was conducted, and 2 distinguishable components emerged: a non-party-dimension (loading high on theater/cinema, sport clubs, other clubs/societies, restaurants, and sport events) and a party-dimension (loading high on someone else's home, pubs/bars, discos/nightclubs, outdoor public places, special events, and home). Differential impacts of drinking location profiles were observed on severe negative alcohol-related consequences (SAC). Relative to those classified as low or intermediate in both dimensions, no significant difference experiencing SAC was found among those who were classified as high in the non-party-dimension only. However, those who were classified as high in the party-dimension alone or in both dimensions were more likely to experience SAC. These differential effects remained after adjusting for alcohol consumption (volume and risky single-occasion drinking), personality traits, and peer-influence [adjusted OR = 0.83 (0.68-1.02), 1.57 (1.27-1.96), and 1.72 (1.23-2.41), respectively], indicating independent effects of drinking location on SAC. The inclusion of sociodemographic factors did not alter this association. The fact that this cluster of party-dimension locations seems to predispose young men to experiencing SAC has important implications for alcohol control policies.

Does drinking location matter? Profiles of risky single-occasion drinking by location and alcohol-related harm among young men

Directory of Open Access Journals (Sweden)

Caroline eBähler

2014-06-01

Full Text Available In adolescents and young adults, acute consequences like injuries account for a substantial proportion of alcohol-related harm, especially in risky single-occasion (RSO drinkers. The primary aim of the study was to characterize different drinking profiles in RSO drinkers according to drinking locations and their relationship to negative, alcohol-related consequences. The sample consisted of 2746 young men from the Cohort Study on Substance Use Risk Factors (C-SURF who had reported drinking 6 or more drinks on a single occasion at least monthly over the preceding 12 months. Principal component analysis on the frequency and amount of drinking at 11 different locations was conducted, and two distinguishable components emerged: a non-party-dimension (loading high on theatre/cinema, sport clubs, other clubs/societies, restaurants, and sport events and a party-dimension (loading high on someone else’s home, pubs/bars, discos/nightclubs, outdoor public places, special events, and home. Differential impacts of drinking location profiles were observed on severe negative alcohol-related consequences (SAC. Relative to those classified as low or intermediate in both dimensions, no significant difference experiencing SAC was found among those who were classified as high in the non-party-dimension only. However, those who were classified as high in the party-dimension alone or in both dimensions were more likely to experience SAC. These differential effects remained after adjusting for alcohol consumption (volume and RSOD, personality traits, and peer-influence (adjusted OR=0.83 [0.68-1.02], 1.57 [1.27-1.96] and 1.72 [1.23-2.41], respectively, indicating independent effects of drinking location on SAC. The inclusion of sociodemographic factors did not alter this association. The fact that this cluster of party-dimension locations seems to predispose young men to experiencing SAC has important implications for alcohol control policies.

Automatic gamma radiation scanning device and feed mechanism for plural sample holders

International Nuclear Information System (INIS)

Byrd, W.J.

1976-01-01

Apparatus is disclosed for measuring the level of gamma radiation contained in a plurality of biological samples which are located on the fibrous sheet member carried by a sample holder. The apparatus is adapted to count the radiation level of the number of closely spaced samples located in rows and columns on the sheet by automatically sequencing through the individual samples within the rows and to advance the holder to bring successive rows into proximity with the detector. The detector is moved from sample to sample within the rows, although a number of detectors can be employed. A plurality of sample holders are automatically advanced to the detector. 25 claims, 5 drawing figures

Internet Geo-Location

Science.gov (United States)

2017-12-01

INTERNET GEO-LOCATION DUKE UNIVERSITY DECEMBER 2017 FINAL TECHNICAL REPORT APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED STINFO COPY AIR...REPORT TYPE FINAL TECHNICAL REPORT 3. DATES COVERED (From - To) MAY 2014 – MAY 2017 4. TITLE AND SUBTITLE INTERNET GEO-LOCATION 5a. CONTRACT...of SpeedTest servers that are used by end users to measure the speed of their Internet connection. The servers log the IP address and the location

Nonlinear Spatial Inversion Without Monte Carlo Sampling

Science.gov (United States)

Curtis, A.; Nawaz, A.

2017-12-01

High-dimensional, nonlinear inverse or inference problems usually have non-unique solutions. The distribution of solutions are described by probability distributions, and these are usually found using Monte Carlo (MC) sampling methods. These take pseudo-random samples of models in parameter space, calculate the probability of each sample given available data and other information, and thus map out high or low probability values of model parameters. However, such methods would converge to the solution only as the number of samples tends to infinity; in practice, MC is found to be slow to converge, convergence is not guaranteed to be achieved in finite time, and detection of convergence requires the use of subjective criteria. We propose a method for Bayesian inversion of categorical variables such as geological facies or rock types in spatial problems, which requires no sampling at all. The method uses a 2-D Hidden Markov Model over a grid of cells, where observations represent localized data constraining the model in each cell. The data in our example application are seismic properties such as P- and S-wave impedances or rock density; our model parameters are the hidden states and represent the geological rock types in each cell. The observations at each location are assumed to depend on the facies at that location only - an assumption referred to as `localized likelihoods'. However, the facies at a location cannot be determined solely by the observation at that location as it also depends on prior information concerning its correlation with the spatial distribution of facies elsewhere. Such prior information is included in the inversion in the form of a training image which represents a conceptual depiction of the distribution of local geologies that might be expected, but other forms of prior information can be used in the method as desired. The method provides direct (pseudo-analytic) estimates of posterior marginal probability distributions over each variable

Sampling strategies for estimating brook trout effective population size

Science.gov (United States)

Andrew R. Whiteley; Jason A. Coombs; Mark Hudy; Zachary Robinson; Keith H. Nislow; Benjamin H. Letcher

2012-01-01

The influence of sampling strategy on estimates of effective population size (Ne) from single-sample genetic methods has not been rigorously examined, though these methods are increasingly used. For headwater salmonids, spatially close kin association among age-0 individuals suggests that sampling strategy (number of individuals and location from...

Hydraulic experiments on the failed fuel location module of prototype fast breeder reactor

International Nuclear Information System (INIS)

Rajesh, K.; Kumar, S.; Padmakumar, G.; Prakash, V.; Vijayashree, R.; Rajan Babu, V.; Govinda Rajan, S.; Vaidyanathan, G.; Prabhaker, R.

2003-01-01

The design of Prototype Fast Breeder Reactor (PFBR) is based on sound design concepts with emphasis on intrinsic safety. The uncertainties involved in the design of various components, which are difficult to assess theoretically, are experimentally verified before design is validated. In PFBR core, the coolant (liquid sodium) enters the bottom of the fuel subassembly, passes over the fuel pins picking up the fission heat and issues in to a hot pool. If there is any breach in the fuel pins, the fission products come in direct contact with the coolant. This is undesirable and it is necessary to locate the subassembly with the failed fuel pin and to isolate it. A component called Failed Fuel Location Module (FFLM) is employed for locating the failed SA by monitoring the coolant samples coming out of each Subassembly. The coolant sample from each Subassembly is drawn by FFLM using an EM pump through sampling tube and selector valve and is monitored for the presence of delayed neutrons which is an indication of failure of the Subassembly. The pressure drop across the selector valve determines the rating of the EM Pump. The dilution of the coolant sample across the selector valve determines the effectiveness of monitoring for contamination. It is not possible to predict pressure drop across the selector valve and dilution of the coolant sample theoretically. These two parameters are determined using a hydraulic experiment on the FFLM. The experiment was carried out in conditions that simulate the reactor conditions following appropriate similarity laws. The paper discusses the details of the model, techniques of experiments and the results from the studies

Location Privacy with Randomness Consistency

Directory of Open Access Journals (Sweden)

Wu Hao

2016-10-01

Full Text Available Location-Based Social Network (LBSN applications that support geo-location-based posting and queries to provide location-relevant information to mobile users are increasingly popular, but pose a location-privacy risk to posts. We investigated existing LBSNs and location privacy mechanisms, and found a powerful potential attack that can accurately locate users with relatively few queries, even when location data is well secured and location noise is applied. Our technique defeats previously proposed solutions including fake-location detection and query rate limits.

Quantitative analysis of Curcuminoid collected from different location in Indonesia by TLC-Densitometry and its antioxidant capacity

Science.gov (United States)

Wahyuni, D. S. C.; Artanti, A. N.; Rinanto, Y.

2018-04-01

Curcuminoid, consisting of curcumin, demethoxycurcumin and bis demethoxycurcumin, is the active compound in Curcuma longa L. rhizome. It yielded vary depend on the environment and varieties. Curcumin has been known to have a potent antioxidants activity. The present work was conducted to assess the curcuminoid content and antioxidant capacity in the crude extracts of C. longa L. collected from eight different locations in Indonesia. Samples were collected from eight locations including Java island, Sumatera island and Nusa Tenggara island. All samples were extracted using 96% ethanol and analyzed quantitatively using TLC-Densitometry. Antioxidant activity was assessed using diphenylpicrylhydrazyl (DPPH) radical scavenging assay and analyzed at 517 nm using a spectrophotometer. Curcuminoid content in C. longa varied among eight different locations (0.53±0.05 - 5.33±0.12 % w/w). The highest curcumin, demethoxycurcumin and bisdemethoxycurcumin yield were found in the samples from Magetan (5.33±0.12%, 1.54±0.05%, 0.46±0.02% w/w, respectively). In contrast, the lowest curcumin, demethoxycurcumin and bisdemethoxycurcumin yield were found in the sample from Demak (0.53±0.05%, 0.17±0.05%, 0.17±0.05% w/w, respectively). Antioxidant capacity showed similar for all places unless sample from Magetan which exhibited two times lower than other locations. It is apparently curcuminoid content and antioxidant activity varied among places. These results are useful information for curcuminoid standardization method in pharmaceutical products.

Quarterly sampling of the wetlands along the old F-Area effluent ditch, Revision 1

Energy Technology Data Exchange (ETDEWEB)

Dixon, K.L.; cummins, C.L.

1994-05-01

In May 1994, well point water and bucket samples were collected for tritium and volatile organic compounds in the wetlands along the old F-Area effluent ditch south of 643-E (old burial ground). The well point samples were collected from seven locations and the bucket samples from four locations. Results support that T and VOCs originating from 643-E are outcropping in the wetlands near this ditch. Based on differences in tritium contents at each location, it was determined that the sampling devices intercepted different groundwater flow paths; however, when VOCs were normalized, based on differences in T, resulting well point and bucket VOCs were comparable in most cases.

Validation of Passive Sampling Devices for Monitoring of Munitions Constituents in Underwater Environments

Science.gov (United States)

2017-09-01

and sampling handling was met. All calibration criteria and instrument maintenance was met for all final reported data. 23 3.2 QUALITATIVE ...the relatively large size of each sampling box within the grid, there were no issues associated with locating appropriate anchoring locations, based...quantiative, as only estimated sampling rates were available, or spiked recoveries were lower suggesting the results are qualitative . TNT RDX ADNTs

Considering the Epistemic Uncertainties of the Variogram Model in Locating Additional Exploratory Drillholes

Directory of Open Access Journals (Sweden)

Saeed Soltani

2015-06-01

Full Text Available To enhance the certainty of the grade block model, it is necessary to increase the number of exploratory drillholes and collect more data from the deposit. The inputs of the process of locating these additional drillholes include the variogram model parameters, locations of the samples taken from the initial drillholes, and the geological block model. The uncertainties of these inputs will lead to uncertainties in the optimal locations of additional drillholes. Meanwhile, the locations of the initial data are crisp, but the variogram model parameters and the geological model have uncertainties due to the limitation of the number of initial data. In this paper, effort has been made to consider the effects of variogram uncertainties on the optimal location of additional drillholes using the fuzzy kriging and solve the locating problem with the genetic algorithm (GA optimization method.A bauxite deposit case study has shown the efficiency of the proposed model.

2015 Long-Term Hydrologic Monitoring Program Sampling and Analysis Results at Rio Blanco, Colorado

Energy Technology Data Exchange (ETDEWEB)

Findlay, Rick [Nararro Research and Engineering, Oak Ridge, TN (United States); Kautsky, Mark [US Department of Energy, Washington, DC (United States). Office of Legacy Management

2015-12-01

The U.S. Department of Energy (DOE) Office of Legacy Management conducted annual sampling at the Rio Blanco, Colorado, Site for the Long-Term Hydrologic Monitoring Program (LTHMP) on May 20–21, 2015. This report documents the analytical results of the Rio Blanco annual monitoring event, the trip report, and the data validation package. The groundwater and surface water monitoring samples were shipped to the GEL Group Inc. laboratories for conventional analysis of tritium and analysis of gamma-emitting radionuclides by high-resolution gamma spectrometry. A subset of water samples collected from wells near the Rio Blanco site was also sent to GEL Group Inc. for enriched tritium analysis. All requested analyses were successfully completed. Samples were collected from a total of four onsite wells, including two that are privately owned. Samples were also collected from two additional private wells at nearby locations and from nine surface water locations. Samples were analyzed for gamma-emitting radionuclides by high-resolution gamma spectrometry, and they were analyzed for tritium using the conventional method with a detection limit on the order of 400 picocuries per liter (pCi/L). Four locations (one well and three surface locations) were analyzed using the enriched tritium method, which has a detection limit on the order of 3 pCi/L. The enriched locations included the well at the Brennan Windmill and surface locations at CER-1, CER-4, and Fawn Creek 500 feet upstream.

Performance test of SAUNA xenon mobile sampling system

International Nuclear Information System (INIS)

Hu Dan; Yang Bin; Yang Weigeng; Jia Huaimao; Wang Shilian; Li Qi; Zhao Yungang; Fan Yuanqing; Chen Zhanying; Chang Yinzhong; Liu Shujiang; Zhang Xinjun; Wang Jun

2011-01-01

In this article, the structure and basic functions of SAUNA noble gas xenon mobile sampling system are introduced. The sampling capability of this system is about 2.2 mL per day, as a result from a 684-h operation. The system can be transported to designated locations conveniently to collect xenon sample for routine or emergency environment monitoring. (authors)

Smartphones as locative media

CERN Document Server

Frith, Jordan

2015-01-01

Smartphone adoption has surpassed 50% of the population in more than 15 countries, and there are now more than one million mobile applications people can download to their phones. Many of these applications take advantage of smartphones as locative media, which is what allows smartphones to be located in physical space. Applications that take advantage of people's location are called location-based services, and they are the focus of this book. Smartphones as locative media raise important questions about how we understand the complicated relationship between the Internet and physical space

Dealing with Insufficient Location Fingerprints in Wi-Fi Based Indoor Location Fingerprinting

Directory of Open Access Journals (Sweden)

Kai Dong

2017-01-01

Full Text Available The development of the Internet of Things has accelerated research in the indoor location fingerprinting technique, which provides value-added localization services for existing WLAN infrastructures without the need for any specialized hardware. The deployment of a fingerprinting based localization system requires an extremely large amount of measurements on received signal strength information to generate a location fingerprint database. Nonetheless, this requirement can rarely be satisfied in most indoor environments. In this paper, we target one but common situation when the collected measurements on received signal strength information are insufficient, and show limitations of existing location fingerprinting methods in dealing with inadequate location fingerprints. We also introduce a novel method to reduce noise in measuring the received signal strength based on the maximum likelihood estimation, and compute locations from inadequate location fingerprints by using the stochastic gradient descent algorithm. Our experiment results show that our proposed method can achieve better localization performance even when only a small quantity of RSS measurements is available. Especially when the number of observations at each location is small, our proposed method has evident superiority in localization accuracy.

Identification of sources of aerosol particles in three locations in eastern Botswana

Science.gov (United States)

Chimidza, S.; Moloi, K.

2000-07-01

Airborne particles have been collected using a dichotomous virtual impactor at three different locations in the eastern part of Botswana: Serowe, Selibe-Phikwe, and Francistown. The particles were separated into two fractions (fine and coarse). Sampling at the three locations was done consecutively during the months of July and August, which are usually dry and stable. The sampling time for each sample was 12 hours during the day. For elemental composition, energy-dispersive x-ray fluorescence technique was used. Correlations and principal component analysis with varimax rotation were used to identify major sources of aerosol particles. In all the three places, soil was found to be the main source of aerosol particles. A copper-nickel mine and smelter at Selibe-Phikwe was found to be not only a source of copper and nickel particles in Selibe-Phikwe but also a source of these particles in far places like Serowe. In Selibe-Phikwe and Francistown, car exhaust was found to be the major source of fine particles of lead and bromine.

Location decision strategies for improving SMME business performance

Directory of Open Access Journals (Sweden)

Shereen Barnard

2011-12-01

Full Text Available Purpose: The primary objective of this study is to investigate the macro-environmental factors that may influence location decisions and how these choices may affect the business performance of SMMEs. Problem investigated: SMMEs in South Africa play an increasingly important role in stimulating economic activity, growth and employment creation. However, many SMMEs cease to exist within the first five years of operation due to various challenges faced by SMMEs on a daily basis. Many SMMEs owners disregard the importance of location, yet the geographical location can negatively influence the survival of the business. Several factors influence the choice of the location, which will ultimately have either a positive or negative effect on business performance. Methodology: A positivistic research methodology was adopted for this study. Seven hypotheses were constructed to achieve the primary objective of this study. The population for this study consisted of SMMEs in the Nelson Mandela Metropole from which a convenience sample of 175 SMMEs was selected. The measuring instrument, a self-developed questionnaire, consisted of three sections. The data collected included the demographical data of the respondents and their businesses, statements on location and various factors influencing location decisions as well as measurements of business performance. Cronbach Alpha coefficients were calculated to determine the reliability of the questionnaire items. Data analysis was done by calculating descriptive statistics, Pearson correlation coefficients and conducting a simple linear regression analysis. Cohen's d was used to determine the significance of between-factor differences. Findings and implications: The results of the study showed that positive relationships existed between all the independent variables (location, rental rates, employment, inflation, interest rates and green buildings and the dependent variable (business performance except for the

Note: A simple image processing based fiducial auto-alignment method for sample registration.

Science.gov (United States)

Robertson, Wesley D; Porto, Lucas R; Ip, Candice J X; Nantel, Megan K T; Tellkamp, Friedjof; Lu, Yinfei; Miller, R J Dwayne

2015-08-01

A simple method for the location and auto-alignment of sample fiducials for sample registration using widely available MATLAB/LabVIEW software is demonstrated. The method is robust, easily implemented, and applicable to a wide variety of experiment types for improved reproducibility and increased setup speed. The software uses image processing to locate and measure the diameter and center point of circular fiducials for distance self-calibration and iterative alignment and can be used with most imaging systems. The method is demonstrated to be fast and reliable in locating and aligning sample fiducials, provided here by a nanofabricated array, with accuracy within the optical resolution of the imaging system. The software was further demonstrated to register, load, and sample the dynamically wetted array.

Law Enforcement Locations

Data.gov (United States)

Kansas Data Access and Support Center — Law Enforcement Locations in Kansas Any location where sworn officers of a law enforcement agency are regularly based or stationed. Law enforcement agencies "are...

SCADA based radioactive sample bottle delivery system for fuel reprocessing project

International Nuclear Information System (INIS)

Kaushik, Subrat; Munj, Niket; Chauhan, R.K.; Kumar, Pramod; Mishra, A.C.

2011-01-01

Radioactive samples of process streams need to be analyzed in centralized control lab for measuring concentration of heavy elements as well as activity at various stages of re-processing plants. The sample is taken from biologically shielded process cells remotely through sampling blisters in sample bottles. These are then transferred to control lab located about 50 meters using vacuum transfer system. The bottle movement is tracked from origin to destination in rich HMI SCADA system using Infra-red non contact type proximity sensors located along sampling line and these sensors are connected to PLC in a fail-safe mode. The sample bottle travels at a speed of 10 m/s under vacuum motive force and the detection time is of the order of 1 mS. The contact time Flow meters have been used to know the air flow in sampling line

Apparatus for sectioning demountable semiconductor samples

Science.gov (United States)

Sopori, B.L.; Wolf, A.

1984-01-01

Apparatus for use during polishing and sectioning operations of a ribbon sample is described. The sample holder includes a cylinder having an axially extending sample cavity terminated in a first funnel-shaped opening and a second slot-like opening. A spring-loaded pressure plunger is located adjacent the second opening of the sample cavity for frictional engagement of the sample cavity. A heat softenable molding medium is inserted in the funnel-shaped opening, to surround the sample. After polishing, the heater is energized to allow draining of the molding medium from the sample cavity. During manual polishing, the second end of the sample holder is inserted in a support ring which provides mechanical support as well as alignment of the sample holder during polishing. A gauge block for measuring the protrusion of a sample beyond the second wall of the holder is also disclosed.

Low complexity algorithms to independently and jointly estimate the location and range of targets using FMCW

KAUST Repository

Ahmed, Sajid

2017-05-12

The estimation of angular-location and range of a target is a joint optimization problem. In this work, to estimate these parameters, by meticulously evaluating the phase of the received samples, low complexity sequential and joint estimation algorithms are proposed. We use a single-input and multiple-output (SIMO) system and transmit frequency-modulated continuous-wave signal. In the proposed algorithm, it is shown that by ignoring very small value terms in the phase of the received samples, fast-Fourier-transform (FFT) and two-dimensional FFT can be exploited to estimate these parameters. Sequential estimation algorithm uses FFT and requires only one received snapshot to estimate the angular-location. Joint estimation algorithm uses two-dimensional FFT to estimate the angular-location and range of the target. Simulation results show that joint estimation algorithm yields better mean-squared-error (MSE) for the estimation of angular-location and much lower run-time compared to conventional MUltiple SIgnal Classification (MUSIC) algorithm.

Low complexity algorithms to independently and jointly estimate the location and range of targets using FMCW

KAUST Repository

Ahmed, Sajid; Jardak, Seifallah; Alouini, Mohamed-Slim

2017-01-01

The estimation of angular-location and range of a target is a joint optimization problem. In this work, to estimate these parameters, by meticulously evaluating the phase of the received samples, low complexity sequential and joint estimation algorithms are proposed. We use a single-input and multiple-output (SIMO) system and transmit frequency-modulated continuous-wave signal. In the proposed algorithm, it is shown that by ignoring very small value terms in the phase of the received samples, fast-Fourier-transform (FFT) and two-dimensional FFT can be exploited to estimate these parameters. Sequential estimation algorithm uses FFT and requires only one received snapshot to estimate the angular-location. Joint estimation algorithm uses two-dimensional FFT to estimate the angular-location and range of the target. Simulation results show that joint estimation algorithm yields better mean-squared-error (MSE) for the estimation of angular-location and much lower run-time compared to conventional MUltiple SIgnal Classification (MUSIC) algorithm.

Cadmium and lead contamination in japonica rice grains and its variation among the different locations in southeast China

International Nuclear Information System (INIS)

Cheng Fangmin; Zhao Ningchun; Xu Haiming; Li Yi; Zhang Wenfang; Zhu Zhiwei; Chen Mingxue

2006-01-01

On the basis of a large-scale survey with 269 sampling sites and a field experiment with 12 cultivars grown at 3 ecologically different locations, Cadmium (Cd) and lead (Pb) contamination in milled rice grains and its variation among different locations were investigated in the area of southeast China. The objective of this study was mainly to assess the present situation of Cd and Pb contamination in rice grains harvested locally and find out the variation of Cd and Pb background levels in rice grains among the diverse regional locations. The results showed that: a) Cd concentrations in milled rice grains ranged from trace (below 10 ng/g) to 340 ng/g, with the means of 81.4 ng/g (AM) and 55.2 ng/g (GM) for the 269 samples, whereas Pb concentrations ranged from trace (below 10 ng/g) to 1136 ng/g, with the means of 113.5 ng/g (AM) and 51.0 ng/g (GM), respectively. High frequency was observed for both the Cd and Pb concentrations ranging from trace to 200 ng/g, with 95.9% for Cd and 84.8% for Pb, respectively. b) ANOVA for the AMs and GMs among 269 sampling sites indicated that there were significant differences among the different spatial locations in Cd or Pb concentrations. c) The Cd concentrations in milled rice grains were poorly correlated with Pb concentration among the 269 sampling sites surveyed, and no significant difference (P > 0.05) in the AMs or GMs of Cd and Pb concentration was observed among different cities within a range of the same provinces, only with an exception for 1-2 provinces. d) Variance analysis of Cd, Pb concentrations for 12 rice cultivars grown in three locations showed that the great difference in coefficients of variation (CV) was observed both among cultivars grown in the same location and among locations of cultivars planted, in which locations showed much more contribution to the variation of Cd or Pb concentration in milled rice grains as compared with cultivars

Hanford Site Environmental Surveillance Master Sampling Schedule for Calendar Year 2008

Energy Technology Data Exchange (ETDEWEB)

Bisping, Lynn E.

2008-01-01

Environmental surveillance of the Hanford Site and surrounding areas is conducted by Pacific Northwest National Laboratory for the U.S. Department of Energy. Sampling is conducted to evaluate levels of radioactive and nonradioactive pollutants in the Hanford environs, as required in DOE Order 450.1, "Environmental Protection Program," and DOE Order 5400.5, "Radiation Protection of the Public and the Environment." The environmental surveillance sampling design is described in the "Hanford Site Environmental Monitoring Plan, United States Department of Energy, Richland Operations Office." This document contains the calendar year 2008 schedule for the routine collection of samples for the Surface Environmental Surveillance Project and Drinking Water Monitoring Project. Each section includes sampling locations, sampling frequencies, sample types, and analyses to be performed. In some cases, samples are scheduled on a rotating basis. If a sample will not be collected in 2008, the anticipated year for collection is provided. Maps showing approximate sampling locations are included for media scheduled for collection in 2008.

Location | FNLCR Staging

Science.gov (United States)

The Frederick National Laboratory for Cancer Research campus is located 50 miles northwest of Washington, D.C., and 50 miles west of Baltimore, Maryland, in Frederick, Maryland. Satellite locations include leased and government facilities extending s

Technology for home dementia care: A prototype locating system put to the test.

Science.gov (United States)

Megges, Herlind; Freiesleben, Silka Dawn; Jankowski, Natalie; Haas, Brigitte; Peters, Oliver

2017-09-01

The user experience of persons with dementia and their primary caregivers with locating systems is not firmly established. Eighteen dyads used a prototype locating system during 4 weeks. Primary outcome measures were ratings of usability, and product functions and features. Secondary outcome measures were caregiver burden, perceived self-efficacy, frequency of use, and willingness to purchase the prototype. Changes in scores between baseline (T 1 ) and end of testing period (T 2 ) were compared by performing independent and dependent samples correlations and descriptive statistics. Seventeen dyads made up the final sample. Ratings of usability and product functions and features were fair, but usability ratings were significantly reduced after 4 weeks. Although the prototype was used infrequently by majority of the participants, most caregivers would be willing to purchase the prototype, with men more willing than women. No significant change in technological willingness, caregiver burden, or perceived self-efficacy was found between T 1 and T 2 . Perceived self-efficacy significantly negatively correlated with willingness to purchase the prototype after 4 weeks. Results highlight the importance of including end users in the research and development phase of locating systems to improve the user experience in home dementia care. Necessary indications for further research are carrying out randomized controlled trials with larger, more representative samples and developing innovative software and hardware solutions.

Privacy for location-based services

CERN Document Server

Ghinita, Gabriel

2013-01-01

Sharing of location data enables numerous exciting applications, such as location-based queries, location-based social recommendations, monitoring of traffic and air pollution levels, etc. Disclosing exact user locations raises serious privacy concerns, as locations may give away sensitive information about individuals' health status, alternative lifestyles, political and religious affiliations, etc. Preserving location privacy is an essential requirement towards the successful deployment of location-based applications. These lecture notes provide an overview of the state-of-the-art in locatio

Visual Sample Plan (VSP) - FIELDS Integration

Energy Technology Data Exchange (ETDEWEB)

Pulsipher, Brent A.; Wilson, John E.; Gilbert, Richard O.; Hassig, Nancy L.; Carlson, Deborah K.; Bing-Canar, John; Cooper, Brian; Roth, Chuck

2003-04-19

Two software packages, VSP 2.1 and FIELDS 3.5, are being used by environmental scientists to plan the number and type of samples required to meet project objectives, display those samples on maps, query a database of past sample results, produce spatial models of the data, and analyze the data in order to arrive at defensible decisions. VSP 2.0 is an interactive tool to calculate optimal sample size and optimal sample location based on user goals, risk tolerance, and variability in the environment and in lab methods. FIELDS 3.0 is a set of tools to explore the sample results in a variety of ways to make defensible decisions with quantified levels of risk and uncertainty. However, FIELDS 3.0 has a small sample design module. VSP 2.0, on the other hand, has over 20 sampling goals, allowing the user to input site-specific assumptions such as non-normality of sample results, separate variability between field and laboratory measurements, make two-sample comparisons, perform confidence interval estimation, use sequential search sampling methods, and much more. Over 1,000 copies of VSP are in use today. FIELDS is used in nine of the ten U.S. EPA regions, by state regulatory agencies, and most recently by several international countries. Both software packages have been peer-reviewed, enjoy broad usage, and have been accepted by regulatory agencies as well as site project managers as key tools to help collect data and make environmental cleanup decisions. Recently, the two software packages were integrated, allowing the user to take advantage of the many design options of VSP, and the analysis and modeling options of FIELDS. The transition between the two is simple for the user – VSP can be called from within FIELDS, automatically passing a map to VSP and automatically retrieving sample locations and design information when the user returns to FIELDS. This paper will describe the integration, give a demonstration of the integrated package, and give users download

Appraising manufacturing location

NARCIS (Netherlands)

Steenhuis, H.J.; de Bruijn, E.J.

2002-01-01

International location of manufacturing activities is an issue for managers of manufacturing companies as well as public policy makers. For managers, the issue is relevant because international locations offer opportunities for lowering costs due to productivity improvements. For governments the

Direct sampling methods for inverse elastic scattering problems

Science.gov (United States)

Ji, Xia; Liu, Xiaodong; Xi, Yingxia

2018-03-01

We consider the inverse elastic scattering of incident plane compressional and shear waves from the knowledge of the far field patterns. Specifically, three direct sampling methods for location and shape reconstruction are proposed using the different component of the far field patterns. Only inner products are involved in the computation, thus the novel sampling methods are very simple and fast to be implemented. With the help of the factorization of the far field operator, we give a lower bound of the proposed indicator functionals for sampling points inside the scatterers. While for the sampling points outside the scatterers, we show that the indicator functionals decay like the Bessel functions as the sampling point goes away from the boundary of the scatterers. We also show that the proposed indicator functionals continuously dependent on the far field patterns, which further implies that the novel sampling methods are extremely stable with respect to data error. For the case when the observation directions are restricted into the limited aperture, we firstly introduce some data retrieval techniques to obtain those data that can not be measured directly and then use the proposed direct sampling methods for location and shape reconstructions. Finally, some numerical simulations in two dimensions are conducted with noisy data, and the results further verify the effectiveness and robustness of the proposed sampling methods, even for multiple multiscale cases and limited-aperture problems.

Green facility location

NARCIS (Netherlands)

Velázquez Martínez, J.C.; Fransoo, J.C.; Bouchery, Y.; Corbett, C.J.; Fransoo, J.C.; Tan, T.

2017-01-01

Transportation is one of the main contributing factors of global carbon emissions, and thus, when dealing with facility location models in a distribution context, transportation emissions may be substantially higher than the emissions due to production or storage. Because facility location models

Residential Location, Job Location, and Wages: Theory and Empirics

DEFF Research Database (Denmark)

Vejlin, Rune Majlund

-to-job transition without changing workplace location. However, workers making a job-to-job transition which makes the workplace location closer to the residence experiences a wage drop. Furthermore, low wage workers and workers with high transportation costs are more likely to make job-to-job transitions, but also......I develop a stylized partial on-the-job equilibrium search model which incorporate a spatial dimension. Workers reside on a circle and can move at a cost. Each point on the circle has a wage distribution. Implications about wages and job mobility are drawn from the model and tested on Danish...... matched employer-employee data. The model predictions hold true. I find that workers working farther away from their residence earn higher wages. When a worker is making a job-to-job transition where he changes workplace location he experiences a higher wage change than a worker making a job...

Lattice location of diffused Zn atoms in GaAs and InP single crystals

International Nuclear Information System (INIS)

Chan, L.Y.; Yu, K.M.; Ben-Tzur, M.; Haller, E.E.; Jaklevic, J.M.; Walukiewicz, W.; Hanson, C.M.

1991-01-01

We have investigated the saturation phenomenon of the free carrier concentration in p-type GaAs and InP single crystals doped by zinc diffusion. The free hole saturation occurs at 10 20 cm -3 for GaAs, but the maximum concentration for InP appears at mid 10 18 cm -3 . The difference in the saturation hole concentrations for these materials is investigated by studying the incorporation and the lattice location of the impurity zinc, an acceptor when located on a group III atom site. Zinc is diffused into the III-V wafers in a sealed quartz ampoule. Particle-induced x-ray emission with ion-channeling techniques are employed to determine the exact lattice location of the zinc atoms. We have found that over 90% of all zinc atoms occupy Ga sites in the diffused GaAs samples, while for the InP case, the zinc substitutionality is dependent on the cooling rate of the sample after high-temperature diffusion. For the slowly cooled sample, a large fraction (∼90%) of the zinc atoms form random precipitates of Zn 3 P 2 and elemental Zn. However, when rapidly cooled only 60% of the zinc forms such precipitates while the rest occupies specific sites in the InP. We analyze our results in terms of the amphoteric native defect model. We show that the difference in the electrical activity of the Zn atoms in GaAs and InP is a consequence of the different location of the Fermi level stabilization energy in these two materials

Location-based Scheduling

DEFF Research Database (Denmark)

Andersson, Niclas; Christensen, Knud

on the market. However, CPM is primarily an activity based method that takes the activity as the unit of focus and there is criticism raised, specifically in the case of construction projects, on the method for deficient management of construction work and continuous flow of resources. To seek solutions...... to the identified limitations of the CPM method, an alternative planning and scheduling methodology that includes locations is tested. Location-based Scheduling (LBS) implies a shift in focus, from primarily the activities to the flow of work through the various locations of the project, i.e. the building. LBS uses...... the graphical presentation technique of Line-of-balance, which is adapted for planning and management of work-flows that facilitates resources to perform their work without interruptions caused by other resources working with other activities in the same location. As such, LBS and Lean Construction share...

Location condition of nuclear power generation at a viewpoint of location area

International Nuclear Information System (INIS)

Kawase, Kazuharu

1999-01-01

In the thirty years memorial meeting of the National Nuclear Power Generation located Commune Conference (NNGC) held in October, 1998, an extremely important fact was clarified, relation deeply to main aim of NNGC that permanent development was not promised at the location area even if a nuclear power plant was constructed there. Therefore, it is required that Japan government receives operation of three laws on electric source development as soon as possible, establishes a basic target on permanent area promotion in the nuclear power generation located commune, realizes some examples on development of the commune together with nuclear power generation and intends to promoted its location. (G.K.)

Water Sample Points, Navajo Nation, 2000, USACE

Data.gov (United States)

U.S. Environmental Protection Agency — This point shapefile presents the locations and results for water samples collected on the Navajo Nation by the US Army Corps of Engineers (USACE) for the US...

Optimising a fall out dust monitoring sampling programme at a ...

African Journals Online (AJOL)

GREG

Key words: Fall out dust monitoring, cement plant, optimising, air pollution sampling, fall out dust sampler locations. .... applied for those areas where controls are in place. Sampling ..... mass balance in the total cement manufacturing process.

Gaps in sampling and limitations to tree biomass estimation: a review of past sampling efforts over the past 50 years

Science.gov (United States)

Aaron Weiskittel; Jereme Frank; James Westfall; David Walker; Phil Radtke; David Affleck; David Macfarlane

2015-01-01

Tree biomass models are widely used but differ due to variation in the quality and quantity of data used in their development. We reviewed over 250 biomass studies and categorized them by species, location, sampled diameter distribution, and sample size. Overall, less than half of the tree species in Forest Inventory and Analysis database (FIADB) are without a...

Determination of anionic concentrations in ground water samples using ion chromatography

International Nuclear Information System (INIS)

Prathibha, P.; Saradhi, I.V.; Pandit, G.G.; Puranik, V.D.

2011-01-01

Ion chromatography is a powerful separation technique for the quantitative measurement of anions in aqueous samples as well as in soil, sediment and air particulate samples leached in aqueous solutions. Ion chromatographic technique is developed by making use of suppressed ion conductivity detection (Small et.al.,1975) and it is a rapid multi ion analysis technique. The time, processing and effort required for the analysis of anions is much less compared to other techniques available such as ion selective electrode technique. In the present paper ground water samples collected around New BARC campus, Visakhapatnam are analyzed for anions using Ion chromatograph. The data generated will establish the current baseline status of the ionic contaminants in the study area. Groundwater samples are collected at 13 locations around BARC Vizag campus covering 30 km radius in September, 2009, April and July, 2010. The water samples include samples from hand pump and open wells in villages. The water samples are analyzed for fluoride, chloride, nitrate and sulphate using Metrohm make Ion chromatograph. The fluoride concentration in samples varied from 0.22 to 1.26 ppm, chloride from 18.7 to 810.9, nitrate from 1.34 to 378.5 ppm and sulphate from 13.29 to 250.69 ppm. No significant seasonal variations are observed in the samples collected from various locations except chloride at two locations. Ions Chromatograph is found to be a useful tool for simultaneous analysis of environmental samples with good accuracy where the concentrations of anions vary within an order of magnitude among them themselves. (author)

Discrete element method (DEM) simulations of stratified sampling during solid dosage form manufacturing.

Science.gov (United States)

Hancock, Bruno C; Ketterhagen, William R

2011-10-14

Discrete element model (DEM) simulations of the discharge of powders from hoppers under gravity were analyzed to provide estimates of dosage form content uniformity during the manufacture of solid dosage forms (tablets and capsules). For a system that exhibits moderate segregation the effects of sample size, number, and location within the batch were determined. The various sampling approaches were compared to current best-practices for sampling described in the Product Quality Research Institute (PQRI) Blend Uniformity Working Group (BUWG) guidelines. Sampling uniformly across the discharge process gave the most accurate results with respect to identifying segregation trends. Sigmoidal sampling (as recommended in the PQRI BUWG guidelines) tended to overestimate potential segregation issues, whereas truncated sampling (common in industrial practice) tended to underestimate them. The size of the sample had a major effect on the absolute potency RSD. The number of sampling locations (10 vs. 20) had very little effect on the trends in the data, and the number of samples analyzed at each location (1 vs. 3 vs. 7) had only a small effect for the sampling conditions examined. The results of this work provide greater understanding of the effect of different sampling approaches on the measured content uniformity of real dosage forms, and can help to guide the choice of appropriate sampling protocols. Copyright © 2011 Elsevier B.V. All rights reserved.

Coupling a Neural Network with Atmospheric Flow Simulations to Locate and Quantify CH4 Emissions at Well Pads

Science.gov (United States)

Travis, B. J.; Sauer, J.; Dubey, M. K.

2017-12-01

Methane (CH4) leaks from oil and gas production fields are a potentially significant source of atmospheric methane. US DOE's ARPA-E office is supporting research to locate methane emissions at 10 m size well pads to within 1 m. A team led by Aeris Technologies, and that includes LANL, Planetary Science Institute and Rice University has developed an autonomous leak detection system (LDS) employing a compact laser absorption methane sensor, a sonic anemometer and multiport sampling. The LDS system analyzes monitoring data using a convolutional neural network (cNN) to locate and quantify CH4 emissions. The cNN was trained using three sources: (1) ultra-high-resolution simulations of methane transport provided by LANL's coupled atmospheric transport model HIGRAD, for numerous controlled methane release scenarios and methane sampling configurations under variable atmospheric conditions, (2) Field tests at the METEC site in Ft. Collins, CO., and (3) Field data from other sites where point-source surface methane releases were monitored downwind. A cNN learning algorithm is well suited to problems in which the training and observed data are noisy, or correspond to complex sensor data as is typical of meteorological and sensor data over a well pad. Recent studies with our cNN emphasize the importance of tracking wind speeds and directions at fine resolution ( 1 second), and accounting for variations in background CH4 levels. A few cases illustrate the importance of sufficiently long monitoring; short monitoring may not provide enough information to determine accurately a leak location or strength, mainly because of short-term unfavorable wind directions and choice of sampling configuration. Length of multiport duty cycle sampling and sample line flush time as well as number and placement of monitoring sensors can significantly impact ability to locate and quantify leaks. Source location error at less than 10% requires about 30 or more training cases.

Dissipation of contaminants of emerging concern in biosolids applied to non-irrigated farmland in eastern Colorado

Science.gov (United States)

Yager, Tracy; Furlong, Edward T.; Kolpin, Dana W.; Kinney, Chad A.; Zaugg, Steven D.; Burkhardt, Mark R.

2013-01-01

In 2007, a 1.5-year field-scale study was initiated by the U.S. Geological Survey to evaluate the dissipation of contaminants of emerging concern (CECs) following a first agronomic biosolids application to nonirrigated farmland. CECs with the greatest decrease in concentration in the surface biosolids at 180 days post-application included indole, d-limonene, p-cresol, phenol, and skatol. CECs that were present in the largest concentration in 180-day-weathered biosolids included stanols, nonylphenols, bisphenol A, bis(2-ethylhexyl) phthalate, hexahydrohexamethyl cyclopenta-benzopyran (HHCB), and triclosan. CECs that were detected in pre-application soil were 3-beta coprostanol, skatol, acetophenone, beta-sitosterol, beta-stigmastanol, cholesterol, indole, p-cresol, and phenol, most of which are biogenic sterols or fragrances that have natural plant sources in addition to anthropogenic sources, yet their concentrations increased (in some cases, substantially) following biosolids application. Preliminary data indicate the nonylphenols (including NPEO1, NPEO2), OPEO1, benzo[a]pyrene, diethyl phthalate, d-limonene, HHCB, triclosan, and possibly 3-beta coprostanol, skatol, beta-sitosterol, cholesterol, indole, and p-cresol, migrated downward through the soil by 468 days post-application, but indicated little uptake by mature wheat plants. This study indicates that some CECs are sufficiently persistent and mobile to be vertically transported into the soil column following biosolids applications to the land surface, even in semiarid regions.

Field sampling, preparation procedure and plutonium analyses of large freshwater samples

International Nuclear Information System (INIS)

Straelberg, E.; Bjerk, T.O.; Oestmo, K.; Brittain, J.E.

2002-01-01

This work is part of an investigation of the mobility of plutonium in freshwater systems containing humic substances. A well-defined bog-stream system located in the catchment area of a subalpine lake, Oevre Heimdalsvatn, Norway, is being studied. During the summer of 1999, six water samples were collected from the tributary stream Lektorbekken and the lake itself. However, the analyses showed that the plutonium concentration was below the detection limit in all the samples. Therefore renewed sampling at the same sites was carried out in August 2000. The results so far are in agreement with previous analyses from the Heimdalen area. However, 100 times higher concentrations are found in the lowlands in the eastern part of Norway. The reason for this is not understood, but may be caused by differences in the concentrations of humic substances and/or the fact that the mountain areas are covered with snow for a longer period of time every year. (LN)

Impact of Socio-Economic Status of Parents and Family Location on ...

African Journals Online (AJOL)

This study investigated the impact of socio-economic status of parents and family location on truant behaviour of secondary school students in the North-West Senatorial District of Benue State. The survey design was used to carry out the study using a sample of 400 respondents selected from different schools within the ...

Evaluating the accuracy of sampling to estimate central line-days: simplification of the National Healthcare Safety Network surveillance methods.

Science.gov (United States)

Thompson, Nicola D; Edwards, Jonathan R; Bamberg, Wendy; Beldavs, Zintars G; Dumyati, Ghinwa; Godine, Deborah; Maloney, Meghan; Kainer, Marion; Ray, Susan; Thompson, Deborah; Wilson, Lucy; Magill, Shelley S

2013-03-01

To evaluate the accuracy of weekly sampling of central line-associated bloodstream infection (CLABSI) denominator data to estimate central line-days (CLDs). Obtained CLABSI denominator logs showing daily counts of patient-days and CLD for 6-12 consecutive months from participants and CLABSI numerators and facility and location characteristics from the National Healthcare Safety Network (NHSN). Convenience sample of 119 inpatient locations in 63 acute care facilities within 9 states participating in the Emerging Infections Program. Actual CLD and estimated CLD obtained from sampling denominator data on all single-day and 2-day (day-pair) samples were compared by assessing the distributions of the CLD percentage error. Facility and location characteristics associated with increased precision of estimated CLD were assessed. The impact of using estimated CLD to calculate CLABSI rates was evaluated by measuring the change in CLABSI decile ranking. The distribution of CLD percentage error varied by the day and number of days sampled. On average, day-pair samples provided more accurate estimates than did single-day samples. For several day-pair samples, approximately 90% of locations had CLD percentage error of less than or equal to ±5%. A lower number of CLD per month was most significantly associated with poor precision in estimated CLD. Most locations experienced no change in CLABSI decile ranking, and no location's CLABSI ranking changed by more than 2 deciles. Sampling to obtain estimated CLD is a valid alternative to daily data collection for a large proportion of locations. Development of a sampling guideline for NHSN users is underway.

Location capability of a sparse regional network (RSTN) using a multi-phase earthquake location algorithm (REGLOC)

Energy Technology Data Exchange (ETDEWEB)

Hutchings, L.

1994-01-01

The Regional Seismic Test Network (RSTN) was deployed by the US Department of Energy (DOE) to determine whether data recorded by a regional network could be used to detect and accurately locate seismic events that might be clandestine nuclear tests. The purpose of this paper is to evaluate the location capability of the RSTN. A major part of this project was the development of the location algorithm REGLOC and application of Basian a prior statistics for determining the accuracy of the location estimates. REGLOC utilizes all identifiable phases, including backazimuth, in the location. Ninty-four events, distributed throughout the network area, detected by both the RSTN and located by local networks were used in the study. The location capability of the RSTN was evaluated by estimating the location accuracy, error ellipse accuracy, and the percentage of events that could be located, as a function of magnitude. The location accuracy was verified by comparing the RSTN results for the 94 events with published locations based on data from the local networks. The error ellipse accuracy was evaluated by determining whether the error ellipse includes the actual location. The percentage of events located was assessed by combining detection capability with location capability to determine the percentage of events that could be located within the study area. Events were located with both an average crustal model for the entire region, and with regional velocity models along with station corrections obtained from master events. Most events with a magnitude <3.0 can only be located with arrivals from one station. Their average location errors are 453 and 414 km for the average- and regional-velocity model locations, respectively. Single station locations are very unreliable because they depend on accurate backazimuth estimates, and backazimuth proved to be a very unreliable computation.

The new LLNL AMS sample changer

International Nuclear Information System (INIS)

Roberts, M.L.; Norman, P.J.; Garibaldi, J.L.; Hornady, R.S.

1993-01-01

The Center for Accelerator Mass Spectrometry at LLNL has installed a new 64 position AMS sample changer on our spectrometer. This new sample changer has the capability of being controlled manually by an operator or automatically by the AMS data acquisition computer. Automatic control of the sample changer by the data acquisition system is a necessary step towards unattended AMS operation in our laboratory. The sample changer uses a fiber optic shaft encoder for rough rotational indexing of the sample wheel and a series of sequenced pneumatic cylinders for final mechanical indexing of the wheel and insertion and retraction of samples. Transit time from sample to sample varies from 4 s to 19 s, depending on distance moved. Final sample location can be set to within 50 microns on the x and y axis and within 100 microns in the z axis. Changing sample wheels on the new sample changer is also easier and faster than was possible on our previous sample changer and does not require the use of any tools

SCADA based radioactive sample bottle delivery system for fuel reprocessing project

International Nuclear Information System (INIS)

Kaushik, Subrat; Munj, Niket; Chauhan, R.K.; Jayaram, M.N.; Haneef, K.K.M.

2014-01-01

Radioactive samples of process streams need to be analyzed in centralized control lab for measuring concentration of heavy elements as well as activity at various stages of re-processing plants. The sample is taken from biologically shielded process cells remotely through sampling blisters in sample bottles. These are then transferred to control lab located about 50 meters using vacuum transfer system. The bottle movement is tracked from origin to destination in rich HMI SCADA system using Infra-red non contact type proximity sensors located along sampling line and these sensors are connected to PLC in a fail-safe mode. The sample bottle travels at a speed of 10 m/s under vacuum motive force and the detection time is of the order of 1 mS. The flow meters have been used to know the air flow in sampling line. The system has been designed, developed, tested and commissioned and in use for four years. (author)

Carotene location in processed food samples measured by cryo In-SEM Raman.

Science.gov (United States)

Lopez-Sanchez, Patricia; Schumm, Stephan; Pudney, Paul D A; Hazekamp, Johan

2011-09-21

Cryo In-SEM Raman has been used for the first time to localise carotene compounds in a food matrix. Raman spectra of lycopene and β-carotene have been obtained from sampling oil droplets and plant cell structures visualised with cryo-SEM in tomato and carrot based emulsions containing 5% oil. It was possible to identify the carotenoids in both the oil droplets and the cell walls. Furthermore our results gave some indication that the carotenoids were in the non-crystalline state. It has been suggested that a higher amount of carotenes solubilised into the oil phase of the food matrix would lead to a higher bioaccessibility, thus understanding the effect of processing conditions on micronutrients distribution in a food matrix might help the design of plant based food products with a better nutritional quality. This shows improved structural characterisation of the cryo-SEM with the molecular sensitivity of Raman spectroscopy as a promising approach for complex biological problems.

Data Validation Package October 2015 Groundwater and Surface Water Sampling at the Monticello, Utah, Processing Site January 2016

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Jason [U.S. Dept. of Energy, Washington, DC (United States). Office of Legacy Management; Smith, Fred [Navarro Research and Engineering, Inc., Oak Ridge, TN (United States)

2016-01-21

Sampling Period: October 12–14, 2015. This semiannual event includes sampling groundwater and surface water at the Monticello Mill Tailings Site. Sampling and analyses were conducted as specified in the 2004 Monticello Mill Tailings Site Operable Unit III Post-Record of Decision Monitoring Plan, Draft Final and Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated). Samples were collected from 52 of 61 planned locations (15 of 17 former mill site wells, 17 of 18 downgradient wells, 9 of 9 downgradient permeable reactive barrier wells, 2 of 7 seeps and wetlands, and 9 of 10 surface water locations). Locations MW00-07, Seep 1, Seep 2, Seep 3, Seep 5, Seep 6, SW00-01, T01-13, and T01-19 were not sampled because of insufficient water availability. All samples were filtered as specified in the monitoring plan. Duplicate samples were collected from surface water location W3-04 and from monitoring wells 82-08, 92-09, and 92-10. Water levels were measured at all but one sampled well and an additional set of wells. The contaminants of concern (COCs) for the Monticello Mill Tailings Site are arsenic, manganese, molybdenum, nitrate + nitrite as nitrogen (nitrate + nitrite as N), selenium, uranium, and vanadium. Time-concentration graphs of the COCs for all groundwater and surface water locations are included in this report. Locations with COCs that exceeded remediation goals are listed.

Study of Coal Burst Source Locations in the Velenje Colliery

Directory of Open Access Journals (Sweden)

Goran Vižintin

2016-06-01

Full Text Available The Velenje coal mine (VCM is situated on the largest Slovenian coal deposit and in one of the thickest layers of coal known in the world. The thickness of the coal layer causes problems for the efficiency of extraction, since the majority of mining operations is within the coal layer. The selected longwall coal mining method with specific geometry, increasing depth of excavations, changes in stress state and naturally given geomechanical properties of rocks induce seismic events. Induced seismic events can be caused by caving processes, blasting or bursts of coal or the surrounding rock. For 2.5D visualization, data of excavations, ash content and calorific value of coal samples, hanging wall and footwall occurrence, subsidence of the surface and coal burst source locations were collected. Data and interpolation methods available in software package Surfer®12 were statistically analyzed and a Kriging (KRG interpolation method was chosen. As a result 2.5D visualizations of coal bursts source locations with geomechanical properties of coal samples taken at different depth in the coal seam in the VCM were made with data-visualization packages Surfer®12 and Voxler®3.

Involvement of hippocampal NMDA receptors in encoding and consolidation, but not retrieval, processes of spontaneous object location memory in rats.

Science.gov (United States)

Yamada, Kazuo; Arai, Misaki; Suenaga, Toshiko; Ichitani, Yukio

2017-07-28

The hippocampus is thought to be involved in object location recognition memory, yet the contribution of hippocampal NMDA receptors to the memory processes, such as encoding, retention and retrieval, is unknown. First, we confirmed that hippocampal infusion of a competitive NMDA receptor antagonist, AP5 (2-amino-5-phosphonopentanoic acid, 20-40nmol), impaired performance of spontaneous object location recognition test but not that of novel object recognition test in Wistar rats. Next, the effects of hippocampal AP5 treatment on each process of object location recognition memory were examined with three different injection times using a 120min delay-interposed test: 15min before the sample phase (Time I), immediately after the sample phase (Time II), and 15min before the test phase (Time III). The blockade of hippocampal NMDA receptors before and immediately after the sample phase, but not before the test phase, markedly impaired performance of object location recognition test, suggesting that hippocampal NMDA receptors play an important role in encoding and consolidation/retention, but not retrieval, of spontaneous object location memory. Copyright © 2017 Elsevier B.V. All rights reserved.

Onderzoek Location Based Marketing: Mobile = location = effect

NARCIS (Netherlands)

Gisbergen, M.S. van; Huhn, A.E.; Khan, V.J.; Ketelaar, P.E.

2011-01-01

Onderzoekers van de NHTV (Internationaa Hoger Onderwijs Breda, Radboud Universiteit, DVJ Insights en Popai Benelux lieten consumenten in een virtuele supermarkt advertenties via de smartphone ontvangen wanneer men langs het geadverteerde product liep. De uitkomsten laten zien dat 'location based

UMTRA project water sampling and analysis plan -- Shiprock, New Mexico

International Nuclear Information System (INIS)

1994-02-01

Water sampling and analysis plan (WSAP) is required for each U.S. Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site to provide a basis for ground water and surface water sampling at disposal and former processing sites. This WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the monitoring stations at the Navaho Reservation in Shiprock, New Mexico, UMTRA Project site. The purposes of the water sampling at Shiprock for fiscal year (FY) 1994 are to (1) collect water quality data at new monitoring locations in order to build a defensible statistical data base, (2) monitor plume movement on the terrace and floodplain, and (3) monitor the impact of alluvial ground water discharge into the San Juan River. The third activity is important because the community of Shiprock withdraws water from the San Juan River directly across from the contaminated alluvial floodplain below the abandoned uranium mill tailings processing site

Low-sampling-rate ultra-wideband channel estimation using equivalent-time sampling

KAUST Repository

Ballal, Tarig

2014-09-01

In this paper, a low-sampling-rate scheme for ultra-wideband channel estimation is proposed. The scheme exploits multiple observations generated by transmitting multiple pulses. In the proposed scheme, P pulses are transmitted to produce channel impulse response estimates at a desired sampling rate, while the ADC samples at a rate that is P times slower. To avoid loss of fidelity, the number of sampling periods (based on the desired rate) in the inter-pulse interval is restricted to be co-prime with P. This condition is affected when clock drift is present and the transmitted pulse locations change. To handle this case, and to achieve an overall good channel estimation performance, without using prior information, we derive an improved estimator based on the bounded data uncertainty (BDU) model. It is shown that this estimator is related to the Bayesian linear minimum mean squared error (LMMSE) estimator. Channel estimation performance of the proposed sub-sampling scheme combined with the new estimator is assessed in simulation. The results show that high reduction in sampling rate can be achieved. The proposed estimator outperforms the least squares estimator in almost all cases, while in the high SNR regime it also outperforms the LMMSE estimator. In addition to channel estimation, a synchronization method is also proposed that utilizes the same pulse sequence used for channel estimation. © 2014 IEEE.

Multiobjective Optimization for Fixture Locating Layout of Sheet Metal Part Using SVR and NSGA-II

Directory of Open Access Journals (Sweden)

Yuan Yang

2017-01-01

Full Text Available Fixture plays a significant role in determining the sheet metal part (SMP spatial position and restraining its excessive deformation in many manufacturing operations. However, it is still a difficult task to design and optimize SMP fixture locating layout at present because there exist multiple conflicting objectives and excessive computational cost of finite element analysis (FEA during the optimization process. To this end, a new multiobjective optimization method for SMP fixture locating layout is proposed in this paper based on the support vector regression (SVR surrogate model and the elitist nondominated sorting genetic algorithm (NSGA-II. By using ABAQUS™ Python script interface, a parametric FEA model is established. And the fixture locating layout is treated as design variables, while the overall deformation and maximum deformation of SMP under external forces are as the multiple objective functions. First, a limited number of training and testing samples are generated by combining Latin hypercube design (LHD with FEA. Second, two SVR prediction models corresponding to the multiple objectives are established by learning from the limited training samples and are integrated as the multiobjective optimization surrogate model. Third, NSGA-II is applied to determine the Pareto optimal solutions of SMP fixture locating layout. Finally, a multiobjective optimization for fixture locating layout of an aircraft fuselage skin case is conducted to illustrate and verify the proposed method.

Data Validation Package - June 2016 Groundwater and Surface Water Sampling at the Green River, Utah, Disposal Site

Energy Technology Data Exchange (ETDEWEB)

Linard, Joshua [USDOE Office of Legacy Management, Washington, DC (United States); Price, Jeffrey [Navarro Research and Engineering, Inc., Las Vegas, NV (United States)

2016-10-10

This event included annual sampling of groundwater and surface water locations at the Green River, Utah, Disposal Site. Sampling and analyses were conducted as specified in Sampling and Analysis Plan for US. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated, http://energy.gov/lrnldownloads/sampling-and- analysis-plan-us-department-energy-office-legacy-management-sites). Samples were collected from 15 monitoring wells and two surface locations at the disposal site as specified in the draft 2011 Ground Water Compliance Action Plan for the Green River, Utah, Disposal Site. Planned monitoring locations are shown in Attachment 1, Sampling and Analysis Work Order. A duplicate sample was collected from location 0179. One equipment blank was collected during this sampling event. Water levels were measured at all monitoring wells that were sampled. See Attachment 2, Trip Reports for additional details. The analytical data and associated qualifiers can be viewed in environmental database reports and are also available for viewing with dynamic mapping via the GEMS (Geospatial Environmental Mapping System) website at http://gems.lm.doe.gov/#. No issues were identified during the data validation process that requires additional action or follow-up.

ISOLOK VALVE ACCEPTANCE TESTING FOR DWPF SME SAMPLING PROCESS

Energy Technology Data Exchange (ETDEWEB)

Edwards, T.; Hera, K.; Coleman, C.; Jones, M.; Wiedenman, B.

2011-12-05

Evaluation of the Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. Of the opportunities, a focus area related to optimizing the equipment and efficiency of the sample turnaround time for DWPF Analytical Laboratory was identified. The Mechanical Systems & Custom Equipment Development (MS&CED) Section of the Savannah River National Laboratory (SRNL) evaluated the possibility of using an Isolok{reg_sign} sampling valve as an alternative to the Hydragard{reg_sign} valve for taking process samples. Previous viability testing was conducted with favorable results using the Isolok sampler and reported in SRNL-STI-2010-00749 (1). This task has the potential to improve operability, reduce maintenance time and decrease CPC cycle time. This report summarizes the results from acceptance testing which was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 (2) and which was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNL-RP-2011-00145 (3). The Isolok to be tested is the same model which was tested, qualified, and installed in the Sludge Receipt Adjustment Tank (SRAT) sample system. RW-0333P QA requirements apply to this task. This task was to qualify the Isolok sampler for use in the DWPF Slurry Mix Evaporator (SME) sampling process. The Hydragard, which is the current baseline sampling method, was used for comparison to the Isolok sampling data. The Isolok sampler is an air powered grab sampler used to 'pull' a sample volume from a process line. The operation of the sampler is shown in Figure 1. The image on the left shows the Isolok's spool extended into the process line and the image on the right shows the sampler retracted and then dispensing the liquid into the sampling container. To determine tank homogeneity, a Coliwasa sampler was used to grab samples at a high and low location within the mixing tank. Data from

Data Validation Package April 2016 Groundwater and Surface Water Sampling at the Monticello, Utah, Disposal and Processing Sites August 2016

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Jason [USDOE Office of Legacy Management, Washington, DC (United States); Smith, Fred [Navarro Research and Engineering, Oak Ridge, TN (United States)

2016-08-01

This semiannual event includes sampling groundwater and surface water at the Monticello Disposal and Processing Sites. Sampling and analyses were conducted as specified in the Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated) and Program Directive MNT-2016-01. Complete sample sets were collected from 42 of 48 planned locations (9 of 9 former mill site wells, 13 of 13 downgradient wells, 7 of 9 downgradient permeable reactive barrier wells, 4 of 7 seeps and wetlands, and 9 of 10 surface water locations). Planned monitoring locations are shown in Attachment 1, Sampling and Analysis Work Order. Locations R6-M3, SW00-01, Seep 1, Seep 2, and Seep 5 were not sampled due to insufficient water availability. A partial sample was collected at location R4-M3 due to insufficient water. All samples from the permeable reactive barrier wells were filtered as specified in the program directive. Duplicate samples were collected from surface water location Sorenson and from monitoring wells 92-07 and RlO-Ml. Water levels were measured at all sampled wells and an additional set of wells. See Attachment2, Trip Report for additional details. The contaminants of concern (COCs) for the Monticello sites are arsenic, manganese, molybdenum, nitrate+ nitrite as nitrogen (nitrate+ nitrite as N), selenium, uranium, and vanadium. Locations with COCs that exceeded remediation goals are listed in Table 1 and Table 2. Time-concentration graphs of the COCs for all groundwater and surface water locations are included in Attachment 3, Data Presentation. An assessment of anomalous data is included in Attachment 4.

Apparatus for sampling hazardous media

International Nuclear Information System (INIS)

Gardner, J.F.; Showalter, T.W.

1984-01-01

An apparatus for sampling a hazardous medium, such as radioactive or chemical waste, selectively collects a predetermined quantity of the medium in a recess of an end-over-end rotatable valving member. This collected quantity is deposited in a receiving receptacle located in a cavity while the receiving receptacle is in a sealed relationship with a recess to prevent dusting of the sampled media outside the receiving receptacle. The receiving receptacle is removably fitted within a vehicle body which is, in turn, slidably movable upon a track within a transport tube. The receiving receptacle is transported in the vehicle body from its sample receiving position within a container for the hazardous medium to a sample retrieval position outside the medium container. The receiving receptacle may then be removed from the vehicle body, capped and taken to a laboratory for chemical analysis. (author)

Costly location in Hotelling duopoly

NARCIS (Netherlands)

Hinloopen, J.; Martin, S.

We introduce a cost of location into Hotelling's (1929) spatial duopoly model. We derive the general conditions on the cost-of-location function under which a pure strategy price-location Nash equilibrium exists. With linear transportation cost and a suitably specified cost of location that rises

Costly location in Hotelling duopoly

NARCIS (Netherlands)

Hinloopen, J.; Martin, S.

2013-01-01

We introduce a cost of location into Hotelling’s (1929) spatial duopoly. We derive the general conditions on the cost-of-location function under which a pure strategy price-location Nash equilibrium exists. With linear transportation cost and a suitably specified cost of location that rises toward

A gigahertz sampling transient analyzer

International Nuclear Information System (INIS)

Andrieu, F.; Balanca, C.; Bernet, J.M.; Lejeune, G.

1975-01-01

The AN 800 equipment was designed for the purpose of digital conversion of fast signals. The recording device had to be located close to the sensor. The equipment had to be highly reliable and had to transmit its output signals before and electromagnetic pulse disturbance. The sampling approach, with its readiness to digitalization, was selected as more convenient

On English Locative Subjects

Directory of Open Access Journals (Sweden)

Gabriela Brůhová

2017-07-01

Full Text Available The paper analyses English sentences with thematic locative subjects. These subjects were detected as translation counterparts of Czech sentenceinitial locative adverbials realized by prepositional phrases with the prepositions do (into, na (on, v/ve (in, z/ze (from complemented by a noun. In the corresponding English structure, the initial scene-setting adverbial is reflected in the thematic subject, which results in the locative semantics of the subject. The sentences are analysed from syntactic, semantic and FSP aspects. From the syntactic point of view, we found five syntactic patterns of the English sentences with a locative subject (SV, SVA, SVO, SVpassA and SVCs that correspond to Czech sentences with initial locative adverbials. On the FSP level the paper studies the potential of the sentences to implement the Presentation or Quality Scale. Since it is the “semantic content of the verb that actuates the presentation semantics of the sentence” (Duškova, 2015a: 260, major attention is paid to the syntactic-semantic structure of the verb. The analysis of the semantics of the English sentences results in the identification of two semantic classes of verbs which co-occur with the English locative subject.

Location performance objectives for the NNWSI area-to-location screening activity

Energy Technology Data Exchange (ETDEWEB)

Sinnock, S.; Fernandez, J.A.

1984-01-01

Fifty-four objectives were identified to guide the screening of the Nevada Research and Development Area of the Nevada Test Site for relatively favorable locations for the disposal of nuclear waste in a mined geologic repository. The objectives were organized as a hierarchy composed of 4 upper-level, 12 middle-level, and 38 lower-level objectives. The four upper-level objectives account for broad national goals to contain and isolate nuclear waste in an environmentally sound and economically acceptable manner. The middle-level objectives correspond to topical categories that logically relate the upper-level objectives to site-specific concerns such as seismicity, sensitive species, and flooding hazards (represented by the lower-level objectives). The relative merits of alternative locations were compared by an application of decision analysis based on standard utility theory. The relative favorabilities of pertinent physical conditions at each alternative location were weighted in relation to the importance of objectives, and summed to produce maps indicating the most and the least favorable locations. Descriptions of the objectives were organized by the hierarchical format; they detail the applicability of each objective to geologic repository siting, previously published siting criteria corresponding to each objective, and the rationale for the weight assigned to each objective, and the pertinent attributes for evaluating locations with respect to each objective. 51 references, 47 figures, 4 tables.

Location performance objectives for the NNWSI area-to-location screening activity

International Nuclear Information System (INIS)

Sinnock, S.; Fernandez, J.A.

1984-01-01

Fifty-four objectives were identified to guide the screening of the Nevada Research and Development Area of the Nevada Test Site for relatively favorable locations for the disposal of nuclear waste in a mined geologic repository. The objectives were organized as a hierarchy composed of 4 upper-level, 12 middle-level, and 38 lower-level objectives. The four upper-level objectives account for broad national goals to contain and isolate nuclear waste in an environmentally sound and economically acceptable manner. The middle-level objectives correspond to topical categories that logically relate the upper-level objectives to site-specific concerns such as seismicity, sensitive species, and flooding hazards (represented by the lower-level objectives). The relative merits of alternative locations were compared by an application of decision analysis based on standard utility theory. The relative favorabilities of pertinent physical conditions at each alternative location were weighted in relation to the importance of objectives, and summed to produce maps indicating the most and the least favorable locations. Descriptions of the objectives were organized by the hierarchical format; they detail the applicability of each objective to geologic repository siting, previously published siting criteria corresponding to each objective, and the rationale for the weight assigned to each objective, and the pertinent attributes for evaluating locations with respect to each objective. 51 references, 47 figures, 4 tables

Privacy-Preserving Location-Based Services

Science.gov (United States)

Chow, Chi Yin

2010-01-01

Location-based services (LBS for short) providers require users' current locations to answer their location-based queries, e.g., range and nearest-neighbor queries. Revealing personal location information to potentially untrusted service providers could create privacy risks for users. To this end, our objective is to design a privacy-preserving…

Adaptive sampling program support for expedited site characterization

International Nuclear Information System (INIS)

Johnson, R.

1993-01-01

Expedited site characterizations offer substantial savings in time and money when assessing hazardous waste sites. Key to some of these savings is the ability to adapt a sampling program to the ''real-time'' data generated by an expedited site characterization. This paper presents a two-prong approach to supporting adaptive sampling programs: a specialized object-oriented database/geographical information system for data fusion, management and display; and combined Bayesian/geostatistical methods for contamination extent estimation and sample location selection

Predicting Audience Location on the Basis of the k-Nearest Neighbor Multilabel Classification

Directory of Open Access Journals (Sweden)

Haitao Wu

2014-01-01

Full Text Available Understanding audience location information in online social networks is important in designing recommendation systems, improving information dissemination, and so on. In this paper, we focus on predicting the location distribution of audiences on YouTube. And we transform this problem to a multilabel classification problem, while we find there exist three problems when the classical k-nearest neighbor based algorithm for multilabel classification (ML-kNN is used to predict location distribution. Firstly, the feature weights are not considered in measuring the similarity degree. Secondly, it consumes considerable computing time in finding similar items by traversing all the training set. Thirdly, the goal of ML-kNN is to find relevant labels for every sample which is different from audience location prediction. To solve these problems, we propose the methods of measuring similarity based on weight, quickly finding similar items, and ranking a specific number of labels. On the basis of these methods and the ML-kNN, the k-nearest neighbor based model for audience location prediction (AL-kNN is proposed for predicting audience location. The experiments based on massive YouTube data show that the proposed model can more accurately predict the location of YouTube video audience than the ML-kNN, MLNB, and Rank-SVM methods.

Latin Hypercube Sampling (LHS) at variable resolutions for enhanced watershed scale Soil Sampling and Digital Soil Mapping.

Science.gov (United States)

Hamalainen, Sampsa; Geng, Xiaoyuan; He, Juanxia

2017-04-01

attributes. When working within the same spatial resolution for covariates, however only modifying the desired number of sampling points produced, the change of point location portrayed a strong geospatial relationship when using continuous data. Access to agricultural fields and adjacent land uses is often "pinned" as the greatest deterrent to performing soil sampling for both soil survey and soil attribute validation work. The lack of access can be a result of poor road access and/or difficult geographical conditions to navigate for field work individuals. This seems a simple yet continuous issue to overcome for the scientific community and in particular, soils professionals. The ability to assist with the ease of access to sampling points will be in the future a contribution to the Latin Hypercube Sampling (LHS) approach. By removing all locations in the initial instance from the DEM, the LHS model can be restricted to locations only with access from the adjacent road or trail. To further the approach, a road network geospatial dataset can be included within spatial Geographic Information Systems (GIS) applications to access already produced points using a shortest-distance network method.

Plasma assisted growth of MoO{sub 3} films on different substrate locations relative to sublimation source

Energy Technology Data Exchange (ETDEWEB)

Sharma, Rabindar K., E-mail: rkrksharma6@gmail.com; Saini, Sujit K.; Kumar, Prabhat; Singh, Megha; Reddy, G. B. [Thin film laboratory, Department of Physics, Indian Institute of Technology Delhi, New Delhi – 110016 (India)

2016-05-06

In the present paper, we reported the role of substrate locations relative to source on the growth of MoO{sub 3} films deposited on Ni coated glass substrates using plasma assisted sublimation process (PASP). According to the XRD and SEM results, substrate location is very crucial factor to control the morphology of MoO{sub 3} films and the best nanostructure growth (in terms of alignments and features) is obtained in case of Sample B (in which substrate is placed on source). The structural results point out that all films exhibit only orthorhombic phase of molybdenum oxide (i.e. α-MoO{sub 3})but the most preferential growth is recorded in Sample B due to the presence of intense peaks crossponding to only (0 k 0) family of crystal planes (k = 2, 4,6..). The Raman analysis again confirms the orthorhombic nature of MoO{sub 3} NFs and details of vibrational bondsin Sample B have been given in the present report. The MoO{sub 3} NFs show intense PL emission in wavelength range of 300-700 nm with three peaks located at 415, 490, and 523 nm in accordance to the improved crystallinity in Sample B.

Ambient krypton-85 air sampling at Hanford

International Nuclear Information System (INIS)

Trevathan, M.S.; Price, K.R.

1985-01-01

In the fall of 1982, the Environmental Evaluations Section of Pacific Northwest Laboratory (PNL) initiated a network of continuous 85 Kr air samplers located on and around the Hanford Site. This effort was in response to the resumption of operations at a nuclear fuel reprocessing plant located onsite where 85 Kr was to be released during fuel dissolution. Preoperational data were collected using noble gas samplers designed by the Environmental Protection Agency-Las Vegas (EPA-LV). The samplers functioned erratically resulting in excessive maintenance costs and prompted a search for a new sampling system. State-of-the-art 85 Dr sampling methods were reviewed and found to be too costly, too complex and inappropriate for field application, so a simple bag collection system was designed and field tested. The system is composed of a reinforced, heavy plastic bag, connected to a variable flow pump and housed in a weatherproof enclosure. At the end of the four week sampling period the air in the bag is transferred by a compressor into a pressure tank for easy transport to the laboratory for analysis. After several months of operation, the air sampling system has proven its reliability and sensitivity to ambient levels of 85 Kr

Ambient krypton-85 air sampling at Hanford

International Nuclear Information System (INIS)

Trevathan, M.S.; Price, K.R.

1984-10-01

In the fall of 1982, the Environmental Evaluations Section of Pacific Northwest Laboratory (PNL) initiated a network of continuous krypton-85 air samplers located on and around the Hanford Site. This effort was in response to the resumption of operations at a nuclear fuel reprocessing plant located onsite where krypton-85 was to be released during fuel dissolution. Preoperational data were collected using noble gas samplers designed by the Environmental Protection Agency-Las Vegas (EPA-LV). The samplers functioned erratically resulting in excessive maintenance costs and prompted a search for a new sampling system. State of the art krypton-85 sampling methods were reviewed and found to be too costly, too complex and inappropriate for field application, so a simple bag collection system was designed and field tested. The system is composed of a reinforced, heavy plastic bag, connected to a variable flow pump and housed in a weatherproof enclosure. At the end of the four week sampling period the air in the bag is transferred by a compressor into a pressure tank for easy transport to the laboratory for analysis. After several months of operation, the air sampling system has proven its reliability and sensitivity to ambient levels of krypton-85. 3 references, 3 figures, 1 table

On the Design of Energy-Efficient Location Tracking Mechanism in Location-Aware Computing

Directory of Open Access Journals (Sweden)

MoonBae Song

2005-01-01

Full Text Available The battery, in contrast to other hardware, is not governed by Moore's Law. In location-aware computing, power is a very limited resource. As a consequence, recently, a number of promising techniques in various layers have been proposed to reduce the energy consumption. The paper considers the problem of minimizing the energy used to track the location of mobile user over a wireless link in mobile computing. Energy-efficient location update protocol can be done by reducing the number of location update messages as possible and switching off as long as possible. This can be achieved by the concept of mobility-awareness we propose. For this purpose, this paper proposes a novel mobility model, called state-based mobility model (SMM to provide more generalized framework for both describing the mobility and updating location information of complexly moving objects. We also introduce the state-based location update protocol (SLUP based on this mobility model. An extensive experiment on various synthetic datasets shows that the proposed method improves the energy efficiency by 2 ∼ 3 times with the additional 10% of imprecision cost.

Inorganic elements in sugar samples

International Nuclear Information System (INIS)

Salles, Paulo M.B. de; Campos, Tarcisio P.R. de

2013-01-01

Sugar is considered a safe food ingredient; however, it can be contaminated by organic elements since its planting until its production process. Thus, this study aims at checking the presence of inorganic elements in samples of crystal, refined and brown sugar available for consumption in Brazil. The applied technique was neutron activation analysis, the k 0 method, using the TRIGA MARK - IPR-R1 reactor located at CDTN/CNEN, in Belo Horizonte. It was identified the presence of elements such as, Au, Br, Co, Cr, Hf, K, Na, Sb, Sc and Zn in the samples of crystal/refined sugar and the presence of As, Au, Br, Ca, Co, Cr, Cs, Fe, Hf, K, Na, Sb, Sc, Sm, Sr, Th and Zn in the brown sugar samples. The applied technique was appropriate to this study because it was not necessary to put the samples in solution, essential condition in order to apply other techniques, avoiding contaminations and sample losses, besides allowing a multi elementary detection in different sugar samples. (author)

Inorganic elements in sugar samples

Energy Technology Data Exchange (ETDEWEB)

Salles, Paulo M.B. de; Campos, Tarcisio P.R. de, E-mail: pauladesalles@yahoo.com.br, E-mail: tprcampos@pq.cnpq.br [Universidade Federal de Minas Gerais (DEN/UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Nuclear; Menezes, Maria Angela de B.C., E-mail: menezes@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2013-07-01

Sugar is considered a safe food ingredient; however, it can be contaminated by organic elements since its planting until its production process. Thus, this study aims at checking the presence of inorganic elements in samples of crystal, refined and brown sugar available for consumption in Brazil. The applied technique was neutron activation analysis, the k{sub 0} method, using the TRIGA MARK - IPR-R1 reactor located at CDTN/CNEN, in Belo Horizonte. It was identified the presence of elements such as, Au, Br, Co, Cr, Hf, K, Na, Sb, Sc and Zn in the samples of crystal/refined sugar and the presence of As, Au, Br, Ca, Co, Cr, Cs, Fe, Hf, K, Na, Sb, Sc, Sm, Sr, Th and Zn in the brown sugar samples. The applied technique was appropriate to this study because it was not necessary to put the samples in solution, essential condition in order to apply other techniques, avoiding contaminations and sample losses, besides allowing a multi elementary detection in different sugar samples. (author)

Substation Location in Offshore Wind Farms - A Planar Multi-Facility Location-Routing Problem

OpenAIRE

Amland, Thomas

2014-01-01

In offshore wind farms, two important parts of the design are to determine locations for substations and a cabling layout that connects every turbine to a substation. These problems are interconnected, as the cable layout depends on the choice of location for the substation. In this thesis we investigate how to set the location of substations such that the total cable cost is minimized.

Fast randomized point location without preprocessing in two- and three-dimensional Delaunay triangulations

Energy Technology Data Exchange (ETDEWEB)

Muecke, E.P.; Saias, I.; Zhu, B.

1996-05-01

This paper studies the point location problem in Delaunay triangulations without preprocessing and additional storage. The proposed procedure finds the query point simply by walking through the triangulation, after selecting a good starting point by random sampling. The analysis generalizes and extends a recent result of d = 2 dimensions by proving this procedure to take expected time close to O(n{sup 1/(d+1)}) for point location in Delaunay triangulations of n random points in d = 3 dimensions. Empirical results in both two and three dimensions show that this procedure is efficient in practice.

Evidence for ultra-fast outflows in radio-quiet AGNs: III - location and energetics

OpenAIRE

Tombesi, F.; Cappi, M.; Reeves, J. N.; Braito, V.

2012-01-01

Using the results of a previous X-ray photo-ionization modelling of blue-shifted Fe K absorption lines on a sample of 42 local radio-quiet AGNs observed with XMM-Newton, in this letter we estimate the location and energetics of the associated ultra-fast outflows (UFOs). Due to significant uncertainties, we are essentially able to place only lower/upper limits. On average, their location is in the interval ~0.0003-0.03pc (~10^2-10^4 r_s) from the central black hole, consistent with what is exp...

Data Validation Package June 2016 Groundwater and Surface Water Sampling at the Old and New Rifle, Colorado, Processing Sites September 2016

Energy Technology Data Exchange (ETDEWEB)

Bush, Richard [USDOE Office of Legacy Management (LM), Washington, DC (United States); Lemke, Peter [Navarro Research and Engineering, Inc., Oak Ridge, TN (United States)

2016-10-17

Sampling Period: June 14–17 and July 7, 2016. Water samples were collected from 36 locations at New Rifle and Old Rifle, Colorado, Disposal/Processing Sites. Planned monitoring locations are shown in Attachment 1, Sampling and Analysis Work Order. Duplicate samples were collected from New Rifle locations 0216 and 0855, and Old Rifle location 0655. One equipment blank was collected after decontamination of non-dedicated equipment used to collect one surface water sample. See Attachment 2, Trip Report for additional details. Sampling and analyses were conducted as specified in the Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated, http://energy.gov/lm/downloads/sampling-and- analysis-plan-us-department-energy-office-legacy-management-sites). New Rifle Site Samples were collected at the New Rifle site from 16 monitoring wells and 7 surface locations in compliance with the December 2008 Groundwater Compliance Action Plan [GCAP] for the New Rifle, Colorado, Processing Site (LMS/RFN/S01920). Monitoring well 0216 could not be sampled in June because it was surrounded by standing water due to the high river stage from spring runoff, it was later sampled in July. Monitoring well 0635 and surface location 0322 could not be sampled because access through the elk fence along Interstate 70 has not been completed at this time. Old Rifle Site Samples were collected at the Old Rifle site from eight monitoring wells and five surface locations in compliance with the December 2001 Ground Water Compliance Action Plan for the Old Rifle, Colorado, UMTRA Project Site (GJ0-2000-177-TAR).

Location theory a unified approach

CERN Document Server

Nickel, Stefan

2006-01-01

Although modern location theory is now more than 90 years old, the focus of researchers in this area has been mainly problem oriented. However, a common theory, which keeps the essential characteristics of classical location models, is still missing.This monograph addresses this issue. A flexible location problem called the Ordered Median Problem (OMP) is introduced. For all three main subareas of location theory (continuous, network and discrete location) structural properties of the OMP are presented and solution approaches provided. Numerous illustrations and examples help the reader to bec

RFID Location Algorithm

Directory of Open Access Journals (Sweden)

Wang Zi Min

2016-01-01

Full Text Available With the development of social services, people’s living standards improve further requirements, there is an urgent need for a way to adapt to the complex situation of the new positioning technology. In recent years, RFID technology have a wide range of applications in all aspects of life and production, such as logistics tracking, car alarm, security and other items. The use of RFID technology to locate, it is a new direction in the eyes of the various research institutions and scholars. RFID positioning technology system stability, the error is small and low-cost advantages of its location algorithm is the focus of this study.This article analyzes the layers of RFID technology targeting methods and algorithms. First, RFID common several basic methods are introduced; Secondly, higher accuracy to political network location method; Finally, LANDMARC algorithm will be described. Through this it can be seen that advanced and efficient algorithms play an important role in increasing RFID positioning accuracy aspects.Finally, the algorithm of RFID location technology are summarized, pointing out the deficiencies in the algorithm, and put forward a follow-up study of the requirements, the vision of a better future RFID positioning technology.

Determine the prevalence of Brucella spp. and Leptospira spp. in blood samples by multiplex polymerase chain reaction collected from cattle, sheep and goats in herds located in provinces of Iran

Directory of Open Access Journals (Sweden)

Faham Khamesipour

2014-05-01

Full Text Available Leptospirosis and brucellosis are common zoonosis that affect many species of mammals mostly causing economical losses. Further, very important fact is huge danger for human and animal health around the world. The purpose of the study is to determine the prevalence of Brucella spp. and Leptospira spp. using multiplex polymerase chain reaction (mPCR method, in blood samples collected from cattle, sheep and goats. In this study, a total number of 250 blood samples (5 cc of blood with ethilen diamin tetra asetic acid were collected randomly from 100 cattle, 80 sheep and 70 goats located on 6 herds in Chaharmahal Va Bakhtiari and Esfahan provinces, Iran. After DNA extraction and setting of mPCR for Brucella spp. and Leptospira spp. mPCR products were screened. The DNA of these microorganisms was detected by multiplex PCR from 31 and 21 out of 100 cattle, respectively. Four of 70 goat’s blood samples from goat breeding farms were positive for Leptospira spp. and 11 were positive for Brucella spp. Out of 80 sheep blood samples 23 were positive for Brucella spp. and 14 for Leptospira spp. The results of the present study show ruminant as an important reservoir for transmission of these zoonotic diseases to humans in Iran. mPCR has the ability to concurrently detect both Brucella and Leptospira species from blood samples of ruminants. The convenience and the possibility of detection of both bacteria at a time, strongly support the use of this mPCR for routine diagnostics.

Comparison of radon and radon-daughter grab samples obtained during the winter and summer

International Nuclear Information System (INIS)

Karp, K.E.

1987-08-01

The Technical Measurements Center (TMC), under the auspices of the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) program, is investigating short-term methods for estimating annual average indoor radon-daughter concentrations (RDC). A field study at 40 sample locations in 26 residential structures in Grand Junction, Colorado, was conducted once in the winter and once in the summer. The short-term methods investigated as part of this study include ten-minute radon and radon-daughter grab sampling and hourly RDC measurements. The results of the field study indicate that ten-minute radon grab samples from basement locations are reproducible over different seasons during controlled sampling conditions. Nonbasement radon and RDC grab samples are highly variable even when the use of the location by the occupant is controlled and the ventilation rate is restricted. The grab sampling was performed under controlled occupied conditions. These results confirm that a short-term radon or RDC measurement in a nonbasement location in a house is not a standardized measurement that can be used to infer an annual average concentration. The hourly RDC measurements were performed under three sets of conditions over a 72-hour period. The three sets of conditions were uncontrolled occupied, controlled occupied, and controlled unoccupied. These results indicate that it is not necessary to relocate the occupants during the time of grab sampling. 8 refs., 8 figs., 10 tabs

Single point aerosol sampling: Evaluation of mixing and probe performance in a nuclear stack

Energy Technology Data Exchange (ETDEWEB)

Rodgers, J.C.; Fairchild, C.I.; Wood, G.O. [Los Alamos National Laboratory, NM (United States)] [and others

1995-02-01

Alternative Reference Methodologies (ARMs) have been developed for sampling of radionuclides from stacks and ducts that differ from the methods required by the U.S. EPA. The EPA methods are prescriptive in selection of sampling locations and in design of sampling probes whereas the alternative methods are performance driven. Tests were conducted in a stack at Los Alamos National Laboratory to demonstrate the efficacy of the ARMs. Coefficients of variation of the velocity tracer gas, and aerosol particle profiles were determined at three sampling locations. Results showed numerical criteria placed upon the coefficients of variation by the ARMs were met at sampling stations located 9 and 14 stack diameters from flow entrance, but not at a location that is 1.5 diameters downstream from the inlet. Experiments were conducted to characterize the transmission of 10 {mu}m aerodynamic equivalent diameter liquid aerosol particles through three types of sampling probes. The transmission ratio (ratio of aerosol concentration at the probe exit plane to the concentration in the free stream) was 107% for a 113 L/min (4-cfm) anisokinetic shrouded probe, but only 20% for an isokinetic probe that follows the EPA requirements. A specially designed isokinetic probe showed a transmission ratio of 63%. The shrouded probe performance would conform to the ARM criteria; however, the isokinetic probes would not.

Locational Factors and Foreign Market-entry Considerations for Malaysian Contractors

Directory of Open Access Journals (Sweden)

A.R Abdul_Aziz

2012-11-01

Full Text Available Past studies on contractor internationalisation adopt a unimodelapproach. Taking up the call of a few scholars, a study isconducted, this time by integrating several extant models of fi rminternationalisation. Malaysian international contractors are usedto test this approach. Due to space limitation, this paper is focusedonly on locational factors. It begins by justifying the inclusion oflocational factors in a multi-model approach. Then it posits thatlocational disadvantage is a more intellectually appealing conceptthan locational advantages. Empirically, it shows that the surveyedcontractors evaluate a wide range of factors before making thego/no go decision to enter foreign markets. It also shows thatpsychic distance was not their major concern. Finally, the locationaldisadvantages create a market space for international contractorswith the tenacity to overcome them, which the sampled populationpossessed.

Preserving Geological Samples and Metadata from Polar Regions

Science.gov (United States)

Grunow, A.; Sjunneskog, C. M.

2011-12-01

The Office of Polar Programs at the National Science Foundation (NSF-OPP) has long recognized the value of preserving earth science collections due to the inherent logistical challenges and financial costs of collecting geological samples from Polar Regions. NSF-OPP established two national facilities to make Antarctic geological samples and drill cores openly and freely available for research. The Antarctic Marine Geology Research Facility (AMGRF) at Florida State University was established in 1963 and archives Antarctic marine sediment cores, dredge samples and smear slides along with ship logs. The United States Polar Rock Repository (USPRR) at Ohio State University was established in 2003 and archives polar rock samples, marine dredges, unconsolidated materials and terrestrial cores, along with associated materials such as field notes, maps, raw analytical data, paleomagnetic cores, thin sections, microfossil mounts, microslides and residues. The existence of the AMGRF and USPRR helps to minimize redundant sample collecting, lessen the environmental impact of doing polar field work, facilitates field logistics planning and complies with the data sharing requirement of the Antarctic Treaty. USPRR acquires collections through donations from institutions and scientists and then makes these samples available as no-cost loans for research, education and museum exhibits. The AMGRF acquires sediment cores from US based and international collaboration drilling projects in Antarctica. Destructive research techniques are allowed on the loaned samples and loan requests are accepted from any accredited scientific institution in the world. Currently, the USPRR has more than 22,000 cataloged rock samples available to scientists from around the world. All cataloged samples are relabeled with a USPRR number, weighed, photographed and measured for magnetic susceptibility. Many aspects of the sample metadata are included in the database, e.g. geographical location, sample

An Efficient Constraint Boundary Sampling Method for Sequential RBDO Using Kriging Surrogate Model

Energy Technology Data Exchange (ETDEWEB)

Kim, Jihoon; Jang, Junyong; Kim, Shinyu; Lee, Tae Hee [Hanyang Univ., Seoul (Korea, Republic of); Cho, Sugil; Kim, Hyung Woo; Hong, Sup [Korea Research Institute of Ships and Ocean Engineering, Busan (Korea, Republic of)

2016-06-15

Reliability-based design optimization (RBDO) requires a high computational cost owing to its reliability analysis. A surrogate model is introduced to reduce the computational cost in RBDO. The accuracy of the reliability depends on the accuracy of the surrogate model of constraint boundaries in the surrogated-model-based RBDO. In earlier researches, constraint boundary sampling (CBS) was proposed to approximate accurately the boundaries of constraints by locating sample points on the boundaries of constraints. However, because CBS uses sample points on all constraint boundaries, it creates superfluous sample points. In this paper, efficient constraint boundary sampling (ECBS) is proposed to enhance the efficiency of CBS. ECBS uses the statistical information of a kriging surrogate model to locate sample points on or near the RBDO solution. The efficiency of ECBS is verified by mathematical examples.

Variability in metagenomic samples from the Puget Sound: Relationship to temporal and anthropogenic impacts.

Directory of Open Access Journals (Sweden)

James C Wallace

Full Text Available Whole-metagenome sequencing (WMS has emerged as a powerful tool to assess potential public health risks in marine environments by measuring changes in microbial community structure and function in uncultured bacteria. In addition to monitoring public health risks such as antibiotic resistance determinants, it is essential to measure predictors of microbial variation in order to identify natural versus anthropogenic factors as well as to evaluate reproducibility of metagenomic measurements.This study expands our previous metagenomic characterization of Puget Sound by sampling new nearshore environments including the Duwamish River, an EPA superfund site, and the Hood Canal, an area characterized by highly variable oxygen levels. We also resampled a wastewater treatment plant, nearshore and open ocean sites introducing a longitudinal component measuring seasonal and locational variations and establishing metagenomics sampling reproducibility. Microbial composition from samples collected in the open sound were highly similar within the same season and location across different years, while nearshore samples revealed multi-fold seasonal variation in microbial composition and diversity. Comparisons with recently sequenced predominant marine bacterial genomes helped provide much greater species level taxonomic detail compared to our previous study. Antibiotic resistance determinants and pollution and detoxification indicators largely grouped by location showing minor seasonal differences. Metal resistance, oxidative stress and detoxification systems showed no increase in samples proximal to an EPA superfund site indicating a lack of ecosystem adaptation to anthropogenic impacts. Taxonomic analysis of common sewage influent families showed a surprising similarity between wastewater treatment plant and open sound samples suggesting a low-level but pervasive sewage influent signature in Puget Sound surface waters. Our study shows reproducibility of

Nevada National Security Site Integrated Groundwater Sampling Plan, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Marutzky, Sam; Farnham, Irene

2014-10-01

The purpose of the Nevada National Security Site (NNSS) Integrated Sampling Plan (referred to herein as the Plan) is to provide a comprehensive, integrated approach for collecting and analyzing groundwater samples to meet the needs and objectives of the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) Underground Test Area (UGTA) Activity. Implementation of this Plan will provide high-quality data required by the UGTA Activity for ensuring public protection in an efficient and cost-effective manner. The Plan is designed to ensure compliance with the UGTA Quality Assurance Plan (QAP). The Plan’s scope comprises sample collection and analysis requirements relevant to assessing the extent of groundwater contamination from underground nuclear testing. This Plan identifies locations to be sampled by corrective action unit (CAU) and location type, sampling frequencies, sample collection methodologies, and the constituents to be analyzed. In addition, the Plan defines data collection criteria such as well-purging requirements, detection levels, and accuracy requirements; identifies reporting and data management requirements; and provides a process to ensure coordination between NNSS groundwater sampling programs for sampling of interest to UGTA. This Plan does not address compliance with requirements for wells that supply the NNSS public water system or wells involved in a permitted activity.

Infant Sleep Location and Breastfeeding Practices in the United States, 2011-2014.

Science.gov (United States)

Smith, Lauren A; Geller, Nicole L; Kellams, Ann L; Colson, Eve R; Rybin, Denis V; Heeren, Timothy; Corwin, Michael J

2016-08-01

To describe the prevalence of breastfeeding and sleep location practices among US mothers and the factors associated with these behaviors, including advice received regarding these practices. A nationally representative sample of 3218 mothers who spoke English or Spanish were enrolled at a sample of 32 US birth hospitals between January 2011 and March 2014. Exclusive breastfeeding was reported by 30.5% of mothers, while an additional 29.5% reported partial breastfeeding. The majority of mothers, 65.5%, reported usually room sharing without bed sharing, while 20.7% reported bed sharing. Compared to mothers who room shared without bed sharing, mothers who bed shared were more likely to report exclusive breastfeeding (adjusted odds ratio 2.46, 95% confidence interval 1.76, 3.45) or partial breastfeeding (adjusted odds ratio 1.75, 95% confidence interval 1.33, 2.31). The majority of mothers reported usually room sharing without bed sharing regardless of feeding practices, including 58.2% of exclusively breastfeeding mothers and 70.0% of nonbreastfeeding mothers. Receiving advice regarding sleep location or breastfeeding increased adherence to recommendations in a dose response manner (the adjusted odds of room sharing without bed sharing and exclusive breastfeeding increased as the relevant advice score increased); however, receiving advice regarding sleep location did not affect feeding practices. Many mothers have not adopted the recommended infant sleep location or feeding practices. Receiving advice from multiple sources appears to promote adherence in a dose response manner. Many women are able to both breastfeed and room share without bed sharing, and advice to adhere to both of these recommendations did not decrease breastfeeding rates. Copyright © 2016 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

OLBS: Offline location based services

OpenAIRE

Coelho, P; Ana Aguiar; João Correia Lopes

2011-01-01

Most existing location-based services rely on ubiquitous connectivity to deliver location-based contents to the users. However, connectivity is not available anywhere at anytime even in urban centres. Underground, indoors, remote areas, and foreign countries are examples situations where users commonly do not have guaranteed connectivity but could profit from location-based contents. In this work, we propose an open platform for publishing, distributing and maintaining location-based contents...

Sampling and analysis plan for sludge located on the floor and in the pits of the 105-K basins

International Nuclear Information System (INIS)

BAKER, R.B.

1998-01-01

This Sampling and Analysis Plan (SAP) provides direction for the sampling of the sludge found on the floor and in the remote pits of the 105-K Basins to provide: (1) basic data for the sludges that have not been characterized to-date and (2) representative Sludge material for process tests to be made by the SNF Project/K Basins sludge treatment process subproject. The sampling equipment developed will remove representative samples of the radioactive sludge from underwater at the K Basins, depositing them in shielded containers for transport to the Hanford Site laboratories. Included in the present document is the basic background logic for selection of the samples to meet the requirements established in the Data Quality Objectives (DQO), HNF-2033, for this sampling activity. The present document also includes the laboratory analyses, methods, procedures, and reporting that will be required to meet the DQO

LOCAT - A Data Retrieval Program.

Science.gov (United States)

1984-12-01

onoitode of scified location - P C RADIUS - maximum distance between specified location and C file locationsC . ’ CONNON /LOCN/ LOCLAT, LOCLNG, RADIUS...rrr’, ,r:.- r -’ - r- rJ Z. . . , . -.-. - - - - - - -- , -• .. . . FILMED 8-85 DTIC .-. ... , ,- . . . . ...: .--. :,.:. ..-..-- ,-, .-..-...

Archive-cup insert for liquid-metal sampling

International Nuclear Information System (INIS)

Nelson, P.A.; Kolba, V.M.; Filewicz, E.C.; Holmes, J.T.

1975-01-01

An insert for collecting liquid-metal samples within a vertical casing including an elongated housing with an upper and a lower overflow seal of annular shape is described. The lower seal includes a centrally located pedestal on which a sample cup is disposed. Liquid metal enters the annulus of the upper seal and overflows into the cup which fills and overflows into the lower seal. Liquid-metal overflow from the lower seal is discharged from the insert. On cooling, the liquid metal trapped within the seals solidifies to hermetically isolate the metal sample within the cup. The device is particularly applicable for use with sampling systems on liquid metal-cooled reactors. (U.S.)

Triangulation based inclusion probabilities: a design-unbiased sampling approach

OpenAIRE

Fehrmann, Lutz; Gregoire, Timothy; Kleinn, Christoph

2011-01-01

A probabilistic sampling approach for design-unbiased estimation of area-related quantitative characteristics of spatially dispersed population units is proposed. The developed field protocol includes a fixed number of 3 units per sampling location and is based on partial triangulations over their natural neighbors to derive the individual inclusion probabilities. The performance of the proposed design is tested in comparison to fixed area sample plots in a simulation with two forest stands. ...

Analysis of the Touch-And-Go Surface Sampling Concept for Comet Sample Return Missions

Science.gov (United States)

Mandic, Milan; Acikmese, Behcet; Bayard, David S.; Blackmore, Lars

2012-01-01

This paper studies the Touch-and-Go (TAG) concept for enabling a spacecraft to take a sample from the surface of a small primitive body, such as an asteroid or comet. The idea behind the TAG concept is to let the spacecraft descend to the surface, make contact with the surface for several seconds, and then ascend to a safe location. Sampling would be accomplished by an end-effector that is active during the few seconds of surface contact. The TAG event is one of the most critical events in a primitive body sample-return mission. The purpose of this study is to evaluate the dynamic behavior of a representative spacecraft during the TAG event, i.e., immediately prior, during, and after surface contact of the sampler. The study evaluates the sample-collection performance of the proposed sampling end-effector, in this case a brushwheel sampler, while acquiring material from the surface during the contact. A main result of the study is a guidance and control (G&C) validation of the overall TAG concept, in addition to specific contributions to demonstrating the effectiveness of using nonlinear clutch mechanisms in the sampling arm joints, and increasing the length of the sampling arms to improve robustness.

Preferential sampling in veterinary parasitological surveillance

Directory of Open Access Journals (Sweden)

Lorenzo Cecconi

2016-04-01

Full Text Available In parasitological surveillance of livestock, prevalence surveys are conducted on a sample of farms using several sampling designs. For example, opportunistic surveys or informative sampling designs are very common. Preferential sampling refers to any situation in which the spatial process and the sampling locations are not independent. Most examples of preferential sampling in the spatial statistics literature are in environmental statistics with focus on pollutant monitors, and it has been shown that, if preferential sampling is present and is not accounted for in the statistical modelling and data analysis, statistical inference can be misleading. In this paper, working in the context of veterinary parasitology, we propose and use geostatistical models to predict the continuous and spatially-varying risk of a parasite infection. Specifically, breaking with the common practice in veterinary parasitological surveillance to ignore preferential sampling even though informative or opportunistic samples are very common, we specify a two-stage hierarchical Bayesian model that adjusts for preferential sampling and we apply it to data on Fasciola hepatica infection in sheep farms in Campania region (Southern Italy in the years 2013-2014.

Optimizing Sampling Efficiency for Biomass Estimation Across NEON Domains

Science.gov (United States)

Abercrombie, H. H.; Meier, C. L.; Spencer, J. J.

2013-12-01

Over the course of 30 years, the National Ecological Observatory Network (NEON) will measure plant biomass and productivity across the U.S. to enable an understanding of terrestrial carbon cycle responses to ecosystem change drivers. Over the next several years, prior to operational sampling at a site, NEON will complete construction and characterization phases during which a limited amount of sampling will be done at each site to inform sampling designs, and guide standardization of data collection across all sites. Sampling biomass in 60+ sites distributed among 20 different eco-climatic domains poses major logistical and budgetary challenges. Traditional biomass sampling methods such as clip harvesting and direct measurements of Leaf Area Index (LAI) involve collecting and processing plant samples, and are time and labor intensive. Possible alternatives include using indirect sampling methods for estimating LAI such as digital hemispherical photography (DHP) or using a LI-COR 2200 Plant Canopy Analyzer. These LAI estimations can then be used as a proxy for biomass. The biomass estimates calculated can then inform the clip harvest sampling design during NEON operations, optimizing both sample size and number so that standardized uncertainty limits can be achieved with a minimum amount of sampling effort. In 2011, LAI and clip harvest data were collected from co-located sampling points at the Central Plains Experimental Range located in northern Colorado, a short grass steppe ecosystem that is the NEON Domain 10 core site. LAI was measured with a LI-COR 2200 Plant Canopy Analyzer. The layout of the sampling design included four, 300 meter transects, with clip harvests plots spaced every 50m, and LAI sub-transects spaced every 10m. LAI was measured at four points along 6m sub-transects running perpendicular to the 300m transect. Clip harvest plots were co-located 4m from corresponding LAI transects, and had dimensions of 0.1m by 2m. We conducted regression analyses

From the SEM (IAEA) to the SIMS (ITU): Re-location experiment of μm-size particles - first results

International Nuclear Information System (INIS)

Admon, U.; Donohue, D.; Aigner, H.; Tamborini, G.; Bildstein, O.; Betti, M.

2002-01-01

Full text: Nuclear forensic analysis of individual radioactive particles in the μm-size range can be performed in two steps: in the first, an automated SEM screening of the loaded sample holder, particles of interest (POIs) are located and classified according to their elemental composition and size. In the second, the sample is transferred to a mass spectrometer (usually a SIMS), and individual POIs are re-located and further analyzed for their isotopic composition. Alternatively, selected POIs can be extracted after SEM screening or fission track analysis, and then analyzed in a TIMS or ICPMS. In the SIMS, which has imaging capability of its own, the whole sample is manipulated to bring specific POIs to the ion-beam point of impingement. In all these cases, including re-visiting POIs in the SEM itself, a precise relocation method is essential. The re-location of POIs in the SIMS after they have been identified as such in the SEM is based on the triangulation method. A set of reference marks are 'printed' by vacuum-deposition of metallic thin-film patterns on the sample holder, a flat-polished graphite planchet. These marks, easily recognizable and precisely measurable by both instruments, serve as inherent coordinate system for each sample. The SEM screening provides a list of POIs, each with a data profile comprising stage coordinates, composition, and size. Having measured the stage coordinates of at least 3 linearly-independent reference marks in the SEM and in the SIMS allows predicting the SIMS stage coordinates where the POIs can be found. This paper describes a joint IAEA-ITU experiment aimed at testing the feasibility of the relocation method in two separate laboratories. A flat-polished graphite planchet was loaded with a small number (a few hundreds) of μm-size uranium particles using the NIST method [3] in the ITU clean laboratory. The sample was sent to the IAEA clean laboratory, where the reference marks pattern was 'printed' by vacuum

RaPToRS Sample Delivery System

Science.gov (United States)

Henchen, Robert; Shibata, Kye; Krieger, Michael; Pogozelski, Edward; Padalino, Stephen; Glebov, Vladimir; Sangster, Craig

2010-11-01

At various labs (NIF, LLE, NRL), activated material samples are used to measure reaction properties. The Rapid Pneumatic Transport of Radioactive Samples (RaPToRS) system quickly and safely moves these radioactive samples through a closed PVC tube via airflow. The carrier travels from the reaction chamber to the control and analysis station, pneumatically braking at the outlet. A reversible multiplexer routes samples from various locations near the shot chamber to the analysis station. Also, the multiplexer allows users to remotely load unactivated samples without manually approaching the reaction chamber. All elements of the system (pneumatic drivers, flow control valves, optical position sensors, multiplexers, Geiger counters, and release gates at the analysis station) can be controlled manually or automatically using a custom LabVIEW interface. A prototype is currently operating at NRL in Washington DC. Prospective facilities for Raptors systems include LLE and NIF.

Advanced pressure tube sampling tools

International Nuclear Information System (INIS)

Wittich, K.C.; King, J.M.

2002-01-01

Deuterium concentration is an important parameter that must be assessed to evaluate the Fitness for service of CANDU pressure tubes. In-reactor pressure tube sampling allows accurate deuterium concentration assessment to be made without the expenses associated with fuel channel removal. This technology, which AECL has developed over the past fifteen years, has become the standard method for deuterium concentration assessment. AECL is developing a multi-head tool that would reduce in-reactor handling overhead by allowing one tool to sequentially sample at all four axial pressure tube locations before removal from the reactor. Four sets of independent cutting heads, like those on the existing sampling tools, facilitate this incorporating proven technology demonstrated in over 1400 in-reactor samples taken to date. The multi-head tool is delivered by AECL's Advanced Delivery Machine or other similar delivery machines. Further, AECL has developed an automated sample handling system that receives and processes the tool once out of the reactor. This system retrieves samples from the tool, dries, weighs and places them in labelled vials which are then directed into shielded shipping flasks. The multi-head wet sampling tool and the automated sample handling system are based on proven technology and offer continued savings and dose reduction to utilities in a competitive electricity market. (author)

Air sampling in the workplace

International Nuclear Information System (INIS)

Hickey, E.E.; Stoetzel, G.A.; Strom, D.J.; Cicotte, G.R.; Wiblin, C.M.; McGuire, S.A.

1993-09-01

This report provides technical information on air sampling that will be useful for facilities following the recommendations in the NRC's Regulatory Guide 8.25, Revision 1, ''Air sampling in the Workplace.'' That guide addresses air sampling to meet the requirements in NRC's regulations on radiation protection, 10 CFR Part 20. This report describes how to determine the need for air sampling based on the amount of material in process modified by the type of material, release potential, and confinement of the material. The purposes of air sampling and how the purposes affect the types of air sampling provided are discussed. The report discusses how to locate air samplers to accurately determine the concentrations of airborne radioactive materials that workers will be exposed to. The need for and the methods of performing airflow pattern studies to improve the accuracy of air sampling results are included. The report presents and gives examples of several techniques that can be used to evaluate whether the airborne concentrations of material are representative of the air inhaled by workers. Methods to adjust derived air concentrations for particle size are described. Methods to calibrate for volume of air sampled and estimate the uncertainty in the volume of air sampled are described. Statistical tests for determining minimum detectable concentrations are presented. How to perform an annual evaluation of the adequacy of the air sampling is also discussed

Determination of samples with TSP size at PLTU Pacitan, Jawa Timur have been done

International Nuclear Information System (INIS)

Rusmanto, Tri; Mulyono; Irianto, Bambang

2013-01-01

Sampling is done using equipment High Volume Air Sampler (HVAS) and analysis using gamma spectrometer. Sampling at 3 locations, each location of the sampling carried out 24 hours, air samples on filter conditioned at room temperature, weighed to a contained weight, counting for 24 hours with gamma spectrometer. The result of qualitative and quantitative analysis of filter TSP was contained of locations I Ra-226 = 0,000888 Bq/m 3 , Pb-212 = 0,000356 Bq/m 3 , Pb-214 = 0,000859 Bq/m 3 , Bi-214 = 0,000712 Bq/m 3 , Ac-228 = 0,004447 Bq/m 3 , K-40 = 0,035454 Bq/m 3 ) , Locations II Ra-226 = 0,00113 Bq/m 3 , Pb-212 = 0,00079 Bq/m 3 , Pb-214 = 0,001351 Bq/m 3 , Bi-214 = 0,000433 Bq/m 3 , Ac-228 = 0,007138 Bq/m 3 , K-40 = 0,018532 Bq/m 3 , Locations III Ra-226 = 0,001424 Bq/m 3 , Pb-212 = 0,000208 Bq/m 3 , Pb-214 = 000052 Bq/m 3 , Bi-214 = 0,001408 Bq/m 3 , Ac-228 = 0,008362 Bq/m 3 , K-40 = 0,020536 Bq/m 3 . Radionuclides activity was all still below quality of air enabled by BAPETEN. Become the activities of ambient air of PLTU area still be peaceful enough as settlement area. (author)

GLPP: A Game-Based Location Privacy-Preserving Framework in Account Linked Mixed Location-Based Services

Directory of Open Access Journals (Sweden)

Zhuo Ma

2018-01-01

Full Text Available In Location-Based Services (LBSs platforms, such as Foursquare and Swarm, the submitted position for a share or search leads to the exposure of users’ activities. Additionally, the cross-platform account linkage could aggravate this exposure, as the fusion of users’ information can enhance inference attacks on users’ next submitted location. Hence, in this paper, we propose GLPP, a personalized and continuous location privacy-preserving framework in account linked platforms with different LBSs (i.e., search-based LBSs and share-based LBSs. The key point of GLPP is to obfuscate every location submitted in search-based LBSs so as to defend dynamic inference attacks. Specifically, first, possible inference attacks are listed through user behavioral analysis. Second, for each specific attack, an obfuscation model is proposed to minimize location privacy leakage under a given location distortion, which ensures submitted locations’ utility for search-based LBSs. Third, for dynamic attacks, a framework based on zero-sum game is adopted to joint specific obfuscation above and minimize the location privacy leakage to a balanced point. Experiments on real dataset prove the effectiveness of our proposed attacks in Accuracy, Certainty, and Correctness and, meanwhile, also show the performance of our preserving solution in defense of attacks and guarantee of location utility.

Multi-element analyses of Vietnamese environmental samples for radiation protection

International Nuclear Information System (INIS)

Mai, T.H.; Nguyen, T.B.; Nguyen, T.N.; Yoshida, S.

2005-01-01

The Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) and Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) were used for measuring 8 major and 27 trace elements in food and soil samples collected in Vietnam. The concentration of elements in food samples was different from different locations and also from different food groups. Depth profiles of the elements were discussed for soil samples. (author)

Data Validation Package - April and July 2015 Groundwater and Surface Water Sampling at the Gunnison, Colorado, Processing Site

Energy Technology Data Exchange (ETDEWEB)

Linard, Joshua [Dept. of Energy (DOE), Washington, DC (United States). Office of Legacy Management; Campbell, Sam [Navarro Research and Engineering, Inc., Oak Ridge, TN (United States)

2016-02-01

This event included annual sampling of groundwater and surface water locations at the Gunnison, Colorado, Processing Site. Sampling and analyses were conducted as specified in Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites. Samples were collected from 28 monitoring wells, three domestic wells, and six surface locations in April at the processing site as specified in the 2010 Ground Water Compliance Action Plan for the Gunnison, Colorado, Processing Site. Domestic wells 0476 and 0477 were sampled in July because the homes were unoccupied in April, and the wells were not in use. Duplicate samples were collected from locations 0113, 0248, and 0477. One equipment blank was collected during this sampling event. Water levels were measured at all monitoring wells that were sampled. No issues were identified during the data validation process that requires additional action or follow-up.

Waste sampling and characterization facility (WSCF)

International Nuclear Information System (INIS)

1994-10-01

The Waste Sampling and Characterization Facility (WSCF) complex consists of the main structure (WSCF) and four support structures located in the 600 Area of the Hanford site east of the 200 West area and south of the Hanford Meterology Station. WSCF is to be used for low level sample analysis, less than 2 mRem. The Laboratory features state-of-the-art analytical and low level radiological counting equipment for gaseous, soil, and liquid sample analysis. In particular, this facility is to be used to perform Resource Conservation and Recovery Act (RCRA) of 1976 and Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) of 1980 sample analysis in accordance with U.S. Environmental Protection Agency Protocols, room air and stack monitoring sample analysis, waste water treatment process support, and contractor laboratory quality assurance checks. The samples to be analyzed contain very low concentrations of radioisotopes. The main reason that WSCF is considered a Nuclear Facility is due to the storage of samples at the facility. This maintenance Implementation Plan has been developed for maintenace functions associate with the WSCF

Sexual orientation and spatial position effects on selective forms of object location memory.

Science.gov (United States)

Rahman, Qazi; Newland, Cherie; Smyth, Beatrice Mary

2011-04-01

Prior research has demonstrated robust sex and sexual orientation-related differences in object location memory in humans. Here we show that this sexual variation may depend on the spatial position of target objects and the task-specific nature of the spatial array. We tested the recovery of object locations in three object arrays (object exchanges, object shifts, and novel objects) relative to veridical center (left compared to right side of the arrays) in a sample of 35 heterosexual men, 35 heterosexual women, and 35 homosexual men. Relative to heterosexual men, heterosexual women showed better location recovery in the right side of the array during object exchanges and homosexual men performed better in the right side during novel objects. However, the difference between heterosexual and homosexual men disappeared after controlling for IQ. Heterosexual women and homosexual men did not differ significantly from each other in location change detection with respect to task or side of array. These data suggest that visual space biases in processing categorical spatial positions may enhance aspects of object location memory in heterosexual women. Copyright © 2010 Elsevier Inc. All rights reserved.

Industrial location and competitiveness

NARCIS (Netherlands)

S. Brakman (Steven); J.H. Garretsen (Harry); J.G.M. van Marrewijk (Charles)

2006-01-01

textabstractThe interaction between the extent of location advantages and the intensity of firm competition relative to the size of the market jointly determines the location of industrial activity. Technology, factor endowments, geography, and scale economies are influential for determining

Design of a TDOA location engine and development of a location system based on chirp spread spectrum.

Science.gov (United States)

Wang, Rui-Rong; Yu, Xiao-Qing; Zheng, Shu-Wang; Ye, Yang

2016-01-01

Location based services (LBS) provided by wireless sensor networks have garnered a great deal of attention from researchers and developers in recent years. Chirp spread spectrum (CSS) signaling formatting with time difference of arrival (TDOA) ranging technology is an effective LBS technique in regards to positioning accuracy, cost, and power consumption. The design and implementation of the location engine and location management based on TDOA location algorithms were the focus of this study; as the core of the system, the location engine was designed as a series of location algorithms and smoothing algorithms. To enhance the location accuracy, a Kalman filter algorithm and moving weighted average technique were respectively applied to smooth the TDOA range measurements and location results, which are calculated by the cooperation of a Kalman TDOA algorithm and a Taylor TDOA algorithm. The location management server, the information center of the system, was designed with Data Server and Mclient. To evaluate the performance of the location algorithms and the stability of the system software, we used a Nanotron nanoLOC Development Kit 3.0 to conduct indoor and outdoor location experiments. The results indicated that the location system runs stably with high accuracy at absolute error below 0.6 m.

Dose Rate Calculations for Rotary Mode Core Sampling Exhauster

CERN Document Server

Foust, D J

2000-01-01

This document provides the calculated estimated dose rates for three external locations on the Rotary Mode Core Sampling (RMCS) exhauster HEPA filter housing, per the request of Characterization Field Engineering.

Dose Rate Calculations for Rotary Mode Core Sampling Exhauster

International Nuclear Information System (INIS)

FOUST, D.J.

2000-01-01

This document provides the calculated estimated dose rates for three external locations on the Rotary Mode Core Sampling (RMCS) exhauster HEPA filter housing, per the request of Characterization Field Engineering

7 CFR 1924.106 - Location.

Science.gov (United States)

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Location. 1924.106 Section 1924.106 Agriculture... CONSTRUCTION AND REPAIR Planning and Performing Site Development Work § 1924.106 Location. (a) General. It is... will not finance development on locations that adversely affect properties which are listed or are...

Sampling method of environmental radioactivity monitoring

International Nuclear Information System (INIS)

1984-01-01

This manual provides sampling methods of environmental samples of airborne dust, precipitated dust, precipitated water (rain or snow), fresh water, soil, river sediment or lake sediment, discharged water from a nuclear facility, grains, tea, milk, pasture grass, limnetic organisms, daily diet, index organisms, sea water, marine sediment, marine organisms, and that for tritium and radioiodine determination for radiation monitoring from radioactive fallout or radioactivity release by nuclear facilities. This manual aims at the presentation of standard sampling procedures for environmental radioactivity monitoring regardless of monitoring objectives, and shows preservation method of environmental samples acquired at the samplingpoint for radiation counting for those except human body. Sampling techniques adopted in this manual is decided by the criteria that they are suitable for routine monitoring and any special skillfulness is not necessary. Based on the above-mentioned principle, this manual presents outline and aims of sampling, sampling position or object, sampling quantity, apparatus, equipment or vessel for sampling, sampling location, sampling procedures, pretreatment and preparation procedures of a sample for radiation counting, necessary recording items for sampling and sample transportation procedures. Special attention is described in the chapter of tritium and radioiodine because these radionuclides might be lost by the above-mentioned sample preservation method for radiation counting of less volatile radionuclides than tritium or radioiodine. (Takagi, S.)

Improvement of vision measurement accuracy using Zernike moment based edge location error compensation model

International Nuclear Information System (INIS)

Cui, J W; Tan, J B; Zhou, Y; Zhang, H

2007-01-01

This paper presents the Zernike moment based model developed to compensate edge location errors for further improvement of the vision measurement accuracy by compensating the slight changes resulting from sampling and establishing mathematic expressions for subpixel location of theoretical and actual edges which are either vertical to or at an angle with X-axis. Experimental results show that the proposed model can be used to achieve a vision measurement accuracy of up to 0.08 pixel while the measurement uncertainty is less than 0.36μm. It is therefore concluded that as a model which can be used to achieve a significant improvement of vision measurement accuracy, the proposed model is especially suitable for edge location of images with low contrast

Library Locations

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Carnegie Library of Pittsburgh locations including address, coordinates, phone number, square footage, and standard operating hours. The map below does not display...

46 CFR 108.493 - Location.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Location. 108.493 Section 108.493 Shipping COAST GUARD... Extinguishing Systems Hand Portable and Semiportable Fire Extinguishing Systems § 108.493 Location. (a) Each... this subpart and installed in the locations prescribed in the table. (b) Each portable and semi...

Remotely detected high-field MRI of porous samples

Science.gov (United States)

Seeley, Juliette A.; Han, Song-I.; Pines, Alexander

2004-04-01

Remote detection of NMR is a novel technique in which an NMR-active sensor surveys an environment of interest and retains memory of that environment to be recovered at a later time in a different location. The NMR or MRI information about the sensor nucleus is encoded and stored as spin polarization at the first location and subsequently moved to a different physical location for optimized detection. A dedicated probe incorporating two separate radio frequency (RF)—circuits was built for this purpose. The encoding solenoid coil was large enough to fit around the bulky sample matrix, while the smaller detection solenoid coil had not only a higher quality factor, but also an enhanced filling factor since the coil volume comprised purely the sensor nuclei. We obtained two-dimensional (2D) void space images of two model porous samples with resolution less than 1.4 mm 2. The remotely reconstructed images demonstrate the ability to determine fine structure with image quality superior to their directly detected counterparts and show the great potential of NMR remote detection for imaging applications that suffer from low sensitivity due to low concentrations and filling factor.

Transuranic waste characterization sampling and analysis plan

International Nuclear Information System (INIS)

1994-01-01

Los Alamos National Laboratory (the Laboratory) is located approximately 25 miles northwest of Santa Fe, New Mexico, situated on the Pajarito Plateau. Technical Area 54 (TA-54), one of the Laboratory's many technical areas, is a radioactive and hazardous waste management and disposal area located within the Laboratory's boundaries. The purpose of this transuranic waste characterization, sampling, and analysis plan (CSAP) is to provide a methodology for identifying, characterizing, and sampling approximately 25,000 containers of transuranic waste stored at Pads 1, 2, and 4, Dome 48, and the Fiberglass Reinforced Plywood Box Dome at TA-54, Area G, of the Laboratory. Transuranic waste currently stored at Area G was generated primarily from research and development activities, processing and recovery operations, and decontamination and decommissioning projects. This document was created to facilitate compliance with several regulatory requirements and program drivers that are relevant to waste management at the Laboratory, including concerns of the New Mexico Environment Department

Fallout Concentration Various Environmental Samples in Indonesia

International Nuclear Information System (INIS)

Sutarman

2001-01-01

The testing of nuclear weapons have been carried out by the advanced countries, such as United States, Russian Federation, United Kingdom, France, China, India and Pakistan, since about 1945 until 1998. Nuclear weapons tests were conducted at various locations, on and above the earth's surface or underground or on and under the ocean's surface. Nuclear explosions caused the radionuclides of fission product, such as 131 l, 89 Sr, 90 Sr, 134 Cs, 137 Cs, and 239 Pu released to the atmospheric layer. In the atmospheric layer, the long-lived radionuclides, i.e, 90 Sr dan 137 Cs will be distributed into the environment as the fallout radionuclides, and deposited in the various environmental samples (soil, water, and biota). In general, at several locations in Indonesia the 90 Sr and 137 Cs in the various environmental samples still can be detected. The data of measurement results of 90 Sr and 137 Cs concentrations were generally lower than that from some countries in the northern hemisphere. (author)

Removal of personal care compounds from sewage sludge in reed bed container (lysimeter) studies--effects of macrophytes.

Science.gov (United States)

Chen, Xijuan; Pauly, Udo; Rehfus, Stefan; Bester, Kai

2009-10-15

Sludge reed beds have been used for dewatering (draining and evapotranspiration) and mineralisation of sludge in Europe since 1988. Although reed beds are considered as a low cost and low contamination method in reducing volume, breaking down organic matter and increasing the density of sludge, it is not yet clear whether this enhanced biological treatment is suitable for degradation of organic micro-pollutants such as personal care products. Within this project the effect of biological sludge treatment in a reed bed on reducing the concentrations of the fragrances HHCB, AHTN, OTNE was studied as on the bactericide Triclosan. Additionally, the capacity of different macrophytes species to affect the treatment process was examined. Three different macrophyte species were compared: bulrush (Typha latifolia), reed (Phragmites australis) and reed canary grass (Phalaris arundinacea). They were planted into containers (lysimeters) with a size of 1 m x 1 m x 1 m which were filled with 20 cm gravel at the bottom and 50 cm sludge on top, into which the macrophytes were planted. During the twelve months experiment reduction of 20-30% for HHCB and AHTN, 70% for Triclosan and 70% for OTNE were determined under environmental conditions. The reduction is most likely due to degradation, since volatilization, uptake into plants and leaching are insignificant. No difference between the containers with different macrophyte species or the unplanted containers was observed. Considering the usual operation time of 10 years for reed beds, an assessment was made for the whole life time.

LOCATION-BASED SERVICES USING SIP

OpenAIRE

Abdullah Azfar,; Md. Sakhawat Hossen,; María José Peroza Marval; Razib Hayat Khan

2010-01-01

Due to the popularity of Location-Based Services and IP telephony, we decided to review a number of different proposals to implement Location-Based Services over a SIP-based mobile network. The result is an interesting overview about the potential functionalities of Location-Based Services and the capabilities of SIP for implementingthese services.

Report of testing and sampling of municipal supply well PM-4

International Nuclear Information System (INIS)

Koch, Richard J.; Longmire, Patrick; Rogers, David B.; Mullen, Ken

1999-01-01

During drilling of regional aquifer characterization borehole R-25, located in the western part of Los Alamos National Laboratory (LANL) at Technical Area (TA) 16, groundwater samples were collected from perched zones of saturation and the regional aquifer that contained elevated levels of high explosive (HE) compounds. One of the nearest Los Alamos County municipal supply wells potentially located down gradient from borehole R-25 is PM-4, located on Mesita del Buey at the west end of TA-54. During the winter of 1998 and 1999 the pump in PM-4 had been removed from the well for scheduled maintenance by the Los Alamos County Public Utilities Department (PUD). Because the pump was removed from PM-4, the opportunity existed to enter the well to (1) perform tests to determine where within the regional aquifer groundwater entered the well and (2) collect groundwater samples from the producing zones for analyses to determine if HE contaminants were present in discrete zones within the regional aquifer. The report of the activities that were performed during March 1999 for the testing and sampling of municipal supply well PM-4 is provided. The report provides a description of the field activities associated with the two phases of the project, including (1) the results of the static and dynamic spinner log surveys, and (2) a description of the sampling activities and the field-measured groundwater quality parameters that were obtained during sampling activities. This report also provides the analytical results of the groundwater samples and a brief discussion of the results of the project

Magnetostratigraphy in the Lodo Formation, CA: An Attempt to Locate Hyperthermals of the Early Eocene

Science.gov (United States)

Aldrich, N. C.; Pluhar, C. J.; Gibbs, S.; Rieth, J. A.

2015-12-01

The Lodo Formation in the California Coast Range, Fresno County records the Paleocene Eocene Thermal Maximum (PETM) and possibly other Early Eocene hyperthermal events. The Eocene Thermal Maximum 2 (ETM2, ELMO, or H1) represents a hyperthermal event that occurred approximately 2 million years after the PETM and just prior to the C24r - C24n magnetic reversal (≈ 53.9 Ma) in the Ypresian. While the ETM2 event has been located in offshore samples, it has been more difficult to locate in a terrestrial section. This project attempts to locate the ETM2 magnetostratigraphically by finding the paleomagnetic reversal at C24r-C24n.3n, provide geochronological framework, and assess sedimentation rate changes during this time. This area is known to have had a high rate of deposition (16.8 cm/kyr ) during the PETM, which is found lower in the section. We collected 36 new samples from a 13.44m section spanning stratigraphy thought to cover the ETM2 along with 31 previous samples spanning the PETM, and prepared them for paleomagnetic and paleontological analysis. We analyzed samples using standard paleomagnetic methods including low-temperature and thermal demagnetization. Preliminary results suggest that the magnetostratigraphy spans the C24r-C24n boundary, while the micropaleontology shows the NP10-NP11 boundary, which occurs near the ETM2 as well as the NP11-NP12 boundary. The data indicate an order-of-magnitude drop in sedimentation rate in the lower Eocene at this site, concomitant with a drop in grain size, compared with the PETM.

PRTR ion exchange vault column sampling

International Nuclear Information System (INIS)

Cornwell, B.C.

1995-01-01

This report documents ion exchange column sampling and Non Destructive Assay (NDA) results from activities in 1994, for the Plutonium Recycle Test Reactor (PRTR) ion exchange vault. The objective was to obtain sufficient information to prepare disposal documentation for the ion exchange columns found in the PRTR Ion exchange vault. This activity also allowed for the monitoring of the liquid level in the lower vault. The sampling activity contained five separate activities: (1) Sampling an ion exchange column and analyzing the ion exchange media for purpose of waste disposal; (2) Gamma and neutron NDA testing on ion exchange columns located in the upper vault; (3) Lower vault liquid level measurement; (4) Radiological survey of the upper vault; and (5) Secure the vault pending waste disposal

Sample pre-concentration with high enrichment factors at a fixed location in paper-based microfluidic devices.

Science.gov (United States)

Yeh, Shih-Hao; Chou, Kuang-Hua; Yang, Ruey-Jen

2016-03-07

The lack of sensitivity is a major problem among microfluidic paper-based analytical devices (μPADs) for early disease detection and diagnosis. Accordingly, the present study presents a method for improving the enrichment factor of low-concentration biomarkers by using shallow paper-based channels realized through a double-sided wax-printing process. In addition, the enrichment factor is further enhanced by exploiting the ion concentration polarization (ICP) effect on the cathodic side of the nanoporous membrane, in which a stationary sample plug is obtained. The occurrence of ICP on the shallow-channel μPAD is confirmed by measuring the current-voltage response as the external voltage is increased from 0 to 210 V (or the field strength from 0 to 1.05 × 10(4) V m(-1)) over 600 s. In addition, to the best of our knowledge, the electroosmotic flow (EOF) speed on the μPAD fabricated with a wax-channel is measured for the first time using a current monitoring method. The experimental results show that for a fluorescein sample, the concentration factor is increased from 130-fold in a conventional full-thickness paper channel to 944-fold in the proposed shallow channel. Furthermore, for a fluorescein isothiocyanate-labeled bovine serum albumin (FITC-BSA) sample, the proposed shallow-channel μPAD achieves an 835-fold improvement in the concentration factor. The concentration technique presented here provides a novel strategy for enhancing the detection sensitivity of μPAD applications.

Preanalytic Factors Associated With Hemolysis in Emergency Department Blood Samples.

Science.gov (United States)

Phelan, Michael P; Reineks, Edmunds Z; Schold, Jesse D; Hustey, Frederic M; Chamberlin, Janelle; Procop, Gary W

2018-02-01

- Hemolysis of emergency department blood samples is a common occurrence and has a negative impact on health care delivery. - To determine the effect of preanalytic factors (straight stick, intravenous [IV] line, needle gauge, location of blood draw, syringe versus vacuum tube use, tourniquet time) on hemolysis in emergency department blood samples. - A single 65 000-visit emergency department's electronic health record was queried for emergency department potassium results and blood draw technique for all samples obtained in calendar year 2014, resulting in 54 531 potassium results. Hemolyzed potassium was measured by hemolysis index. Comparisons of hemolysis by sampling technique were conducted by χ 2 tests. - Overall hemolysis was 10.0% (5439 of 54 531). Hemolysis among samples obtained from straight stick was significantly less than among those obtained with IV line (5.4% [33 of 615] versus 10.2% [4821 of 47 266], P < .001). For IV-placed blood draws, antecubital location had a statistically significant lower overall hemolysis compared with other locations: 7.4% (2117 of 28 786) versus 14.6% (2622 of 17 960) ( P < .001). For blood drawn with a syringe compared with vacuum, hemolysis was 13.0% (92 of 705) and 11.0% (1820 of 16 590), respectively ( P = .09, not significant). For large-gauge IV blood draws versus smaller-gauge IV lines, a lower hemolysis was also observed (9.3% [3882 of 41 571] versus 16.7% [939 of 5633]) ( P < .001). For IV-drawn blood with tourniquet time less than 60 seconds, hemolysis was 10.3% (1362 of 13 162) versus 13.9% for more than 60 seconds (532 of 3832), P < .001. - This study confirmed previous findings that straight stick and antecubital location are significantly associated with reduced hemolysis and indicated that shorter tourniquet time and larger gauge for IV draws were significantly associated with lower hemolysis.

Location-based games

DEFF Research Database (Denmark)

Ejsing-Duun, Stine

In this dissertation, it is explored which prerequisites are necessary in location-based games (LBGs) to make meaningful the meeting between players and spatiality with an emphasis on physical locations. Throughout the dissertation, it has been shown that LBGs affect players’ perception of and be...... possible. The practical contribution is my creation of the LBG Visions of Sara. People continue to play this game in Odense more than two years after its launch, and DJEEO uses it as a showcase, enabling the company to sell similar LBGs....

Sampling Strategies and Processing of Biobank Tissue Samples from Porcine Biomedical Models.

Science.gov (United States)

Blutke, Andreas; Wanke, Rüdiger

2018-03-06

In translational medical research, porcine models have steadily become more popular. Considering the high value of individual animals, particularly of genetically modified pig models, and the often-limited number of available animals of these models, establishment of (biobank) collections of adequately processed tissue samples suited for a broad spectrum of subsequent analyses methods, including analyses not specified at the time point of sampling, represent meaningful approaches to take full advantage of the translational value of the model. With respect to the peculiarities of porcine anatomy, comprehensive guidelines have recently been established for standardized generation of representative, high-quality samples from different porcine organs and tissues. These guidelines are essential prerequisites for the reproducibility of results and their comparability between different studies and investigators. The recording of basic data, such as organ weights and volumes, the determination of the sampling locations and of the numbers of tissue samples to be generated, as well as their orientation, size, processing and trimming directions, are relevant factors determining the generalizability and usability of the specimen for molecular, qualitative, and quantitative morphological analyses. Here, an illustrative, practical, step-by-step demonstration of the most important techniques for generation of representative, multi-purpose biobank specimen from porcine tissues is presented. The methods described here include determination of organ/tissue volumes and densities, the application of a volume-weighted systematic random sampling procedure for parenchymal organs by point-counting, determination of the extent of tissue shrinkage related to histological embedding of samples, and generation of randomly oriented samples for quantitative stereological analyses, such as isotropic uniform random (IUR) sections generated by the "Orientator" and "Isector" methods, and vertical

1995 Phase 1 concrete sampling at the decontaminated 183-H basins

International Nuclear Information System (INIS)

Kramer, C.D.

1996-01-01

This report provides a consolidated reference for 1995 concrete sampling data associated with the Hanford Site's 183-H Solar Evaporation Basins (located at the Hanford Site in Richland, Washington). In 1995, the basins were decontaminated and dismantled. Sampling efforts began after completion of concrete decontamination efforts. Soil and water samples were collected and are described in chronological order in this report

Instrumental neutron activation analysis of soil sample

International Nuclear Information System (INIS)

Abdul Khalik Haji Wood.

1983-01-01

This paper describes the analysis of soil samples collected from 5 different location around Sungai Lui, Kajang, Selangor, Malaysia. These sample were taken at 22-24 cm from the top of the ground and were analysed using the techniques of Instrumental Neutron Activation Analysis (INAA). The analysis on soil sample taken above 22-24 cm level were done in order to determine if there is any variation in elemental contents at different sampling levels. The results indicate a wide variation in the contents of the samples. About 30 elements have been analysed. The major ones are Na, I, Cl, Mg, Al, K, Ti, Ca and Fe. Trace elements analysed were Ba, Sc, V, Cr, Mn, Ga, As, Zn, Br, Rb, Co, Hf, Zr, Th, U, Sb, Cs, Ce, Sm, Eu, Tb, Dy, Yb, Lu and La. (author)

Modeling discrete competitive facility location

CERN Document Server

Karakitsiou, Athanasia

2015-01-01

This book presents an up-to-date review of modeling and optimization approaches for location problems along with a new bi-level programming methodology which captures the effect of competition of both producers and customers on facility location decisions. While many optimization approaches simplify location problems by assuming decision making in isolation, this monograph focuses on models which take into account the competitive environment in which such decisions are made. New insights in modeling, algorithmic and theoretical possibilities are opened by this approach and new applications are possible. Competition on equal term plus competition between market leader and followers are considered in this study, consequently bi-level optimization methodology is emphasized and further developed. This book provides insights regarding modeling complexity and algorithmic approaches to discrete competitive location problems. In traditional location modeling, assignment of customer demands to supply sources are made ...

Gamma spectroscopy analysis of archived Marshall Island soil samples

International Nuclear Information System (INIS)

Herman, S.; Hoffman, K.; Lavelle, K.; Trauth, A.; Glover, S.E.; Connick, W.; Spitz, H.; LaMont, S.P.; Hamilton, T.

2016-01-01

Four samples of archival Marshall Islands soil were subjected to non-destructive, broad energy (17 keV-2.61 MeV) gamma-ray spectrometry analysis using a series of different high-resolution germanium detectors. These archival samples were collected in 1967 from different locations on Bikini Atoll and were contaminated with a range of fission and activation products, and other nuclear material from multiple weapons tests. Unlike samples collected recently, these samples have been stored in sealed containers and have been unaffected by approximately 50 years of weathering. Initial results show that the samples contained measurable but proportionally different concentrations of plutonium, 241 Am, and 137 Cs, and 60 Co. (author)

Perspectival Structure and Agentive Self-location

DEFF Research Database (Denmark)

Alsmith, Adrian

2017-01-01

-locating, in the sense that an episode of perceptual experience may be sufficient for thoughts about one’s location. In this chapter, I argue that perceptual experience can conceivably be perspectivally structured without locating its subject and that any account of spatial self-consciousness based upon a simple......Perceptual experience is perspectivally structured, in at least two respects. It has characteristic sensory limitations relative to a given location (limitation-structure) and it presents objects as spatially related to a given location (egocentric-structure). Perceptual experience is also self...... inference from the perspectival structure of perceptual experience faces serious difficulties. If this is correct, then we ought to look beyond the perspectival structure of perceptual experience in order to account for its self-locating content. The Agentive Self-Location Thesis, as developed here...

Accounting for Location Error in Kalman Filters: Integrating Animal Borne Sensor Data into Assimilation Schemes

Science.gov (United States)

Sengupta, Aritra; Foster, Scott D.; Patterson, Toby A.; Bravington, Mark

2012-01-01

Data assimilation is a crucial aspect of modern oceanography. It allows the future forecasting and backward smoothing of ocean state from the noisy observations. Statistical methods are employed to perform these tasks and are often based on or related to the Kalman filter. Typically Kalman filters assumes that the locations associated with observations are known with certainty. This is reasonable for typical oceanographic measurement methods. Recently, however an alternative and abundant source of data comes from the deployment of ocean sensors on marine animals. This source of data has some attractive properties: unlike traditional oceanographic collection platforms, it is relatively cheap to collect, plentiful, has multiple scientific uses and users, and samples areas of the ocean that are often difficult of costly to sample. However, inherent uncertainty in the location of the observations is a barrier to full utilisation of animal-borne sensor data in data-assimilation schemes. In this article we examine this issue and suggest a simple approximation to explicitly incorporate the location uncertainty, while staying in the scope of Kalman-filter-like methods. The approximation stems from a Taylor-series approximation to elements of the updating equation. PMID:22900005

Locating techniques for nuclear power stations

International Nuclear Information System (INIS)

Hayashi, Masao

1983-01-01

The basic thought in locating nuclear power stations is to examine carefully the suitability of sites and the safety of plants, and in the end, to perfect the safety of public. In Japan, effort is exerted to obtain the trust of local people by carrying out investigation, research and examination from respective standpoints of the government, institutes and industries. The author has engaged in the standardization of the investigation, test and analysis regarding the aseismatic capability of ground, the verifying project in Tadotsu of the coupled vibration of ground and structures, the evaluation of the performance of large vibration tables, the future concept of new locating procedure and so on in the last more than ten years. The technological classification of ground, the technological meaning of active faults, the procedure of the aseismatic design of plants, the difference of earthquake input force according to various locating methods, 12 rules regarding the attenuation of vibration of ground, and the concept of new locating method in the 21st century are explained. As the new locating techniques applicable to central Japan, diluvial ground location, floating location in tunnels, underground location, offshore location and so on must be promoted. (Kako, I.)

A proposal of optimal sampling design using a modularity strategy

Science.gov (United States)

Simone, A.; Giustolisi, O.; Laucelli, D. B.

2016-08-01

In real water distribution networks (WDNs) are present thousands nodes and optimal placement of pressure and flow observations is a relevant issue for different management tasks. The planning of pressure observations in terms of spatial distribution and number is named sampling design and it was faced considering model calibration. Nowadays, the design of system monitoring is a relevant issue for water utilities e.g., in order to manage background leakages, to detect anomalies and bursts, to guarantee service quality, etc. In recent years, the optimal location of flow observations related to design of optimal district metering areas (DMAs) and leakage management purposes has been faced considering optimal network segmentation and the modularity index using a multiobjective strategy. Optimal network segmentation is the basis to identify network modules by means of optimal conceptual cuts, which are the candidate locations of closed gates or flow meters creating the DMAs. Starting from the WDN-oriented modularity index, as a metric for WDN segmentation, this paper proposes a new way to perform the sampling design, i.e., the optimal location of pressure meters, using newly developed sampling-oriented modularity index. The strategy optimizes the pressure monitoring system mainly based on network topology and weights assigned to pipes according to the specific technical tasks. A multiobjective optimization minimizes the cost of pressure meters while maximizing the sampling-oriented modularity index. The methodology is presented and discussed using the Apulian and Exnet networks.

Prevalence and location of Listeria monocytogenes in farmed rainbow trout.

Science.gov (United States)

Miettinen, Hanna; Wirtanen, Gun

2005-10-15

A total of 510 rainbow trout originating from fish farms in lakes and sea areas around Finland were studied for the presence of Listeria monocytogenes. Samples were studied as pools from five fish. Gill, viscera, and skin from the pooled samples were analysed separately. The individual samples were analysed later if the pooled sample was found to be Listeria positive. The prevalence of Listeria spp. and L. monocytogenes in pooled unprocessed fresh rainbow trout was on average 35.0% and 14.6%, respectively. On the other hand, the prevalence of Listeria spp. and L. monocytogenes in individual thawed fish was found to be 14.3% and 8.8%, respectively. These numbers tend to overestimate and underestimate the real situation because not all fish in pooled samples were necessarily contaminated and in some of the Listeria positive pooled samples all individual samples turned out to be Listeria free. The prevalence of L. monocytogenes varied greatly between different fish farms from zero to 100% in pooled samples and from zero to 75% according to individually studied fish samples. Some indications of the influence of weather conditions and seasonal variations that strongly affected the Listeria contamination of fish were also noticed. The location of Listeria spp. and L. monocytogenes in different parts of the fish differed with statistical significance in rainbow trout. Up to 95.6% of the L. monocytogenes and 84.5% of Listeria spp. positive samples were gill samples. Only 4.4% (2/45) of the L. monocytogenes positive samples were obtained from skin or viscera. Closer study at one fish farm revealed that there was only one L. monocytogenes ribotype present in the contaminated fish, although water and surfaces were heavily contaminated with six other L. monocytogenes ribotypes.

UMTRA project water sampling and analysis plan, Ambrosia Lake, New Mexico

International Nuclear Information System (INIS)

1994-02-01

This water sampling and analysis plan (WSAP) provides the basis for ground water sampling at the Ambrosia Lake Uranium Mill Tailings Remedial Action (UMTRA) Project site during fiscal year 1994. It identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the monitoring locations and will be updated annually. The Ambrosia Lake site is in McKinley County, New Mexico, about 40 kilometers (km) (25 miles [mi]) north of Grants, New Mexico, and 1.6 km (1 mi) east of New Mexico Highway 509 (Figure 1.1). The town closest to the tailings pile is San Mateo, about 16 km ( 10 mi) southeast (Figure 1.2). The former mill and tailings pile are in Section 28, and two holding ponds are in Section 33, Township 14 North, Range 9 West. The site is shown on the US Geological Survey (USGS) map (USGS, 1980). The site is approximately 2100 meters (m) (7000 feet [ft]) above sea level

Data Validation Package - July 2016 Groundwater Sampling at the Gunnison, Colorado, Disposal Site

Energy Technology Data Exchange (ETDEWEB)

Linard, Joshua [USDOE Office of Legacy Management, Washington, DC (United States); Campbell, Sam [Navarro Research and Engineering, Inc., Las Vegas, NV (United States)

2016-10-25

Groundwater sampling at the Gunnison, Colorado, Disposal Site is conducted every 5 years to monitor disposal cell performance. During this event, samples were collected from eight monitoring wells as specified in the 1997 Long-Term Surveillance Plan for the Gunnison, Colorado, Disposal Site. Sampling and analyses were conducted as specified in the Sampling and Analysis Plan for US Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated, http://energy.gov/lm/downloads/sampling-and­ analysis-plan-us-department-energy-office-legacy-management-sites). Planned monitoring locations are shown in Attachment 1, Sampling and Analysis Work Order. A duplicate sample was collected from location 0723. Water levels were measured at all monitoring wells that were sampled and seven additional wells. The analytical data and associated qualifiers can be viewed in environmental database reports and are also available for viewing with dynamic mapping via the GEMS (Geospatial Environmental Mapping System) website at http://gems.lm.doe.gov/#. No issues were identified during the data validation process that require additional action or follow-up.

A flexible system to capture sample vials in a storage box - the box vial scanner.

Science.gov (United States)

Nowakowski, Steven E; Kressin, Kenneth R; Deick, Steven D

2009-01-01

Tracking sample vials in a research environment is a critical task and doing so efficiently can have a large impact on productivity, especially in high volume laboratories. There are several challenges to automating the capture process, including the variety of containers used to store samples. We developed a fast and robust system to capture the location of sample vials being placed in storage that allows the laboratories the flexibility to use sample containers of varying dimensions. With a single scan, this device captures the box identifier, the vial identifier and the location of each vial within a freezer storage box. The sample vials are tracked through a barcode label affixed to the cap while the boxes are tracked by a barcode label on the side of the box. Scanning units are placed at the point of use and forward data to a sever application for processing the scanned data. Scanning units consist of an industrial barcode reader mounted in a fixture positioning the box for scanning and providing lighting during the scan. The server application transforms the scan data into a list of storage locations holding vial identifiers. The list is then transferred to the laboratory database. The box vial scanner captures the IDs and location information for an entire box of sample vials into the laboratory database in a single scan. The system accommodates a wide variety of vials sizes by inserting risers under the sample box and a variety of storage box layouts are supported via the processing algorithm on the server.

Critique of Hanford Waste Vitrification Plant off-gas sampling requirements

International Nuclear Information System (INIS)

Goles, R.W.

1996-03-01

Off-gas sampling and monitoring activities needed to support operations safety, process control, waste form qualification, and environmental protection requirements of the Hanford Waste Vitrification Plant (HWVP) have been evaluated. The locations of necessary sampling sites have been identified on the basis of plant requirements, and the applicability of Defense Waste Processing Facility (DWPF) reference sampling equipment to these HWVP requirements has been assessed for all sampling sites. Equipment deficiencies, if present, have been described and the bases for modifications and/or alternative approaches have been developed

Air-sampling inlet contamination by aircraft emissions on the NASA CV-990 aircraft

Science.gov (United States)

Condon, E. P.; Vedder, J. F.

1984-01-01

Results of an experimental investigation of the contamination of air sampling inlets by aircraft emissions from the NASA CV-990 research aircraft are presented. This four-engine jet aircraft is a NASA facility used for many different atmospheric and meteorological experiments, as well as for developing spacecraft instrumentation for remote measurements. Our investigations were performed to provide information on which to base the selection of sampling locations for a series of multi-instrument missions for measuring tropospheric trace gases. The major source of contamination is the exhaust from the jet engines, which generate many of the same gases that are of interest in atmospheric chemistry, as well as other gases that may interfere with sampling measurements. The engine exhaust contains these gases in mixing ratios many orders of magnitude greater than those that occur in the clean atmosphere which the missions seek to quantify. Pressurized samples of air were collected simultaneously from a scoop located forward of the engines to represent clean air and from other multiport scoops at various aft positions on the aircraft. The air samples were analyzed in the laboratory by gas chromatography for carbon monoxide, an abundant combustion by-product. Data are presented for various scoop locations under various flight conditions.

Within-person associations of young adolescents’ physical activity across five primary locations: is there evidence of cross-location compensation?

DEFF Research Database (Denmark)

Carlson, Jordan A.; Mitchell, Tarrah B.; Saelens, Brian E.

2017-01-01

Youth are active in multiple locations, but it is unknown whether more physical activity in one location is associated with less in other locations. This cross-sectional study examines whether on days with more physical activity in a given location, relative to their typical activity in that loca......Youth are active in multiple locations, but it is unknown whether more physical activity in one location is associated with less in other locations. This cross-sectional study examines whether on days with more physical activity in a given location, relative to their typical activity...... in that location, youth had less activity in other locations (i.e., within-person associations/compensation)....

A cautionary note on substituting spatial subunits for repeated temporal sampling in studies of site occupancy

Science.gov (United States)

Kendall, William L.; White, Gary C.

2009-01-01

1. Assessing the probability that a given site is occupied by a species of interest is important to resource managers, as well as metapopulation or landscape ecologists. Managers require accurate estimates of the state of the system, in order to make informed decisions. Models that yield estimates of occupancy, while accounting for imperfect detection, have proven useful by removing a potentially important source of bias. To account for detection probability, multiple independent searches per site for the species are required, under the assumption that the species is available for detection during each search of an occupied site. 2. We demonstrate that when multiple samples per site are defined by searching different locations within a site, absence of the species from a subset of these spatial subunits induces estimation bias when locations are exhaustively assessed or sampled without replacement. 3. We further demonstrate that this bias can be removed by choosing sampling locations with replacement, or if the species is highly mobile over a short period of time. 4. Resampling an existing data set does not mitigate bias due to exhaustive assessment of locations or sampling without replacement. 5. Synthesis and applications. Selecting sampling locations for presence/absence surveys with replacement is practical in most cases. Such an adjustment to field methods will prevent one source of bias, and therefore produce more robust statistical inferences about species occupancy. This will in turn permit managers to make resource decisions based on better knowledge of the state of the system.

Multiple surveys employing a new sample-processing protocol reveal the genetic diversity of placozoans in Japan.

Science.gov (United States)

Miyazawa, Hideyuki; Nakano, Hiroaki

2018-03-01

Placozoans, flat free-living marine invertebrates, possess an extremely simple bauplan lacking neurons and muscle cells and represent one of the earliest-branching metazoan phyla. They are widely distributed from temperate to tropical oceans. Based on mitochondrial 16S rRNA sequences, 19 haplotypes forming seven distinct clades have been reported in placozoans to date. In Japan, placozoans have been found at nine locations, but 16S genotyping has been performed at only two of these locations. Here, we propose a new processing protocol, "ethanol-treated substrate sampling," for collecting placozoans from natural environments. We also report the collection of placozoans from three new locations, the islands of Shikine-jima, Chichi-jima, and Haha-jima, and we present the distribution of the 16S haplotypes of placozoans in Japan. Multiple surveys conducted at multiple locations yielded five haplotypes that were not reported previously, revealing high genetic diversity in Japan, especially at Shimoda and Shikine-jima Island. The observed geographic distribution patterns were different among haplotypes; some were widely distributed, while others were sampled only from a single location. However, samplings conducted on different dates at the same sites yielded different haplotypes, suggesting that placozoans of a given haplotype do not inhabit the same site constantly throughout the year. Continued sampling efforts conducted during all seasons at multiple locations worldwide and the development of molecular markers within the haplotypes are needed to reveal the geographic distribution pattern and dispersal history of placozoans in greater detail.

Semantic Location Extraction from Crowdsourced Data

Science.gov (United States)

Koswatte, S.; Mcdougall, K.; Liu, X.

2016-06-01

Crowdsourced Data (CSD) has recently received increased attention in many application areas including disaster management. Convenience of production and use, data currency and abundancy are some of the key reasons for attracting this high interest. Conversely, quality issues like incompleteness, credibility and relevancy prevent the direct use of such data in important applications like disaster management. Moreover, location information availability of CSD is problematic as it remains very low in many crowd sourced platforms such as Twitter. Also, this recorded location is mostly related to the mobile device or user location and often does not represent the event location. In CSD, event location is discussed descriptively in the comments in addition to the recorded location (which is generated by means of mobile device's GPS or mobile communication network). This study attempts to semantically extract the CSD location information with the help of an ontological Gazetteer and other available resources. 2011 Queensland flood tweets and Ushahidi Crowd Map data were semantically analysed to extract the location information with the support of Queensland Gazetteer which is converted to an ontological gazetteer and a global gazetteer. Some preliminary results show that the use of ontologies and semantics can improve the accuracy of place name identification of CSD and the process of location information extraction.

SEMANTIC LOCATION EXTRACTION FROM CROWDSOURCED DATA

Directory of Open Access Journals (Sweden)

S. Koswatte

2016-06-01

Full Text Available Crowdsourced Data (CSD has recently received increased attention in many application areas including disaster management. Convenience of production and use, data currency and abundancy are some of the key reasons for attracting this high interest. Conversely, quality issues like incompleteness, credibility and relevancy prevent the direct use of such data in important applications like disaster management. Moreover, location information availability of CSD is problematic as it remains very low in many crowd sourced platforms such as Twitter. Also, this recorded location is mostly related to the mobile device or user location and often does not represent the event location. In CSD, event location is discussed descriptively in the comments in addition to the recorded location (which is generated by means of mobile device's GPS or mobile communication network. This study attempts to semantically extract the CSD location information with the help of an ontological Gazetteer and other available resources. 2011 Queensland flood tweets and Ushahidi Crowd Map data were semantically analysed to extract the location information with the support of Queensland Gazetteer which is converted to an ontological gazetteer and a global gazetteer. Some preliminary results show that the use of ontologies and semantics can improve the accuracy of place name identification of CSD and the process of location information extraction.

Effects of burn location and investigator on burn depth in a porcine model.

Science.gov (United States)

Singer, Adam J; Toussaint, Jimmy; Chung, Won Taek; Thode, Henry C; McClain, Steve; Raut, Vivek

2016-02-01

In order to be useful, animal models should be reproducible and consistent regardless of sampling bias, investigator creating burn, and burn location. We determined the variability in burn depth based on biopsy location, burn location and investigator in a porcine model of partial thickness burns. 24 partial thickness burns (2.5 cm by 2.5 cm each) were created on the backs of 2 anesthetized pigs by 2 investigators (one experienced, one inexperienced) using a previously validated model. In one of the pigs, the necrotic epidermis covering each burn was removed. Five full thickness 4mm punch biopsies were obtained 1h after injury from the four corners and center of the burns and stained with Hematoxylin and Eosin and Masson's trichrome for determination of burn depth by a board certified dermatopathologist blinded to burn location and investigator. Comparisons of burn depth by biopsy location, burn location and investigator were performed with t-tests and ANOVA as appropriate. The mean (SD) depth of injury to blood vessels (the main determinant of burn progression) in debrided and non-debrided pigs pooled together was 1.8 (0.3)mm, which included 75% of the dermal depth. Non-debrided burns were 0.24 mm deeper than debrided burns (Plocations, in debrided burns. Additionally, there were also no statistical differences in burn depths from midline to lateral in either of these burn types. Burn depth was similar for both investigators and among biopsy locations. Burn depth was greater for caudal locations in non-debrided burns and overall non-debrided burns were deeper than debrided burns. However, burn depth did not differ based on investigator, biopsy site, and medial-lateral location. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Evaluation of Pu sample oscillations in CESAR

Energy Technology Data Exchange (ETDEWEB)

Brunet, M.

1974-10-15

A set of 12 plutonium samples of various compositions were oscillated in CESAR in 1973. Comparisons were made to the oscillated reactivity effect of a known specimen of U-235 and boron where the detector signals were corrected against a background signal based on comparison to the motion of a control rod in the central location of critical assembly. An equivalent sample method was tested first for various samples of U-235 and boron to establish a means of correction in the detector response. Inferred plutonium reaction rates in the experiments were compared to transport theory calculations using the APOLLO code. Addition effort is needed to reconcile differences in measured and calculated results requiring both chemical analyses of the plutonium isotopes in the samples and improved cross sections for the plutonium isotopes.

A "shotgun" method for tracing the birth locations of sheep from flock tags, applied to scrapie surveillance in Great Britain.

Science.gov (United States)

Birch, Colin P D; Del Rio Vilas, Victor J; Chikukwa, Ambrose C

2010-09-01

Movement records are often used to identify animal sample provenance by retracing the movements of individuals. Here we present an alternative method, which uses the same identity tags and movement records as are used to retrace movements, but ignores individual movement paths. The first step uses a simple query to identify the most likely birth holding for every identity tag included in a database recording departures from agricultural holdings. The second step rejects a proportion of the birth holding locations to leave a list of birth holding locations that are relatively reliable. The method was used to trace the birth locations of sheep sampled for scrapie in abattoirs, or on farm as fallen stock. Over 82% of the sheep sampled in the fallen stock survey died at the holding of birth. This lack of movement may be an important constraint on scrapie transmission. These static sheep provided relatively reliable birth locations, which were used to define criteria for selecting reliable traces. The criteria rejected 16.8% of fallen stock traces and 11.9% of abattoir survey traces. Two tests provided estimates that selection reduced error in fallen stock traces from 11.3% to 3.2%, and in abattoir survey traces from 8.1% to 1.8%. This method generated 14,591 accepted traces of fallen stock from samples taken during 2002-2005 and 83,136 accepted traces from abattoir samples. The absence or ambiguity of flock tag records at the time of slaughter prevented the tracing of 16-24% of abattoir samples during 2002-2004, although flock tag records improved in 2005. The use of internal scoring to generate and evaluate results from the database query, and the confirmation of results by comparison with other database fields, are analogous to methods used in web search engines. Such methods may have wide application in tracing samples and in adding value to biological datasets. Crown Copyright 2010. Published by Elsevier B.V. All rights reserved.

Uncapacitated facility location problems: contributions

Directory of Open Access Journals (Sweden)

Galvão Roberto Diéguez

2004-01-01

Full Text Available The objective of the present paper is to review my personal contributions in the field of uncapacitated facility location problems. These contributions took place throughout my academic career, from the time I was a Ph.D. student at Imperial College to the present day. They cover approximately 30 years, from 1973 to 2003; they address: algorithms developed for the p-median problem and for a general formulation of uncapacitated location problems; the study of dynamic location models; covering and hierarchical location problems; queuing-based probabilistic location models. The contributions encompass theoretical developments, computational algorithms and practical applications. All work took place in an academic environment, with the invaluable collaboration of colleagues (both in Brazil and abroad and research students at COPPE. Each section in the paper is dedicated to a topic that involves a personal contribution. Every one of them is placed within the context of the existing literature.

Hair of the dog: obtaining samples from coyotes and wolves noninvasively

Science.gov (United States)

Ausband, David E.; Young, Julie; Fannin, Barbara; Mitchell, Michael S.; Stenglein, Jennifer L.; Waits, Lisette P.; Shivik, John A.

2011-01-01

Canids can be difficult to detect and their populations difficult to monitor. We tested whether hair samples could be collected from coyotes (Canis latrans) in Texas, USA and gray wolves (C. lupus) in Montana, USA using lure to elicit rubbing behavior at both man-made and natural collection devices. We used mitochondrial and nuclear DNA to determine whether collected hair samples were from coyote, wolf, or nontarget species. Both coyotes and wolves rubbed on man-made barbed surfaces but coyotes in Texas seldom rubbed on hanging barbed surfaces. Wolves in Montana showed a tendency to rub at stations where natural-material collection devices (sticks and debris) were present. Time to detection was relatively short (5 nights and 4 nights for coyotes and wolves, respectively) with nontarget and unknown species comprising approximately 26% of the detections in both locations. Eliciting rubbing behavior from coyotes and wolves using lures has advantages over opportunistic genetic sampling methods (e.g., scat transects) because it elicits a behavior that deposits a hair sample at a fixed sampling location, thereby increasing the efficiency of sampling for these canids. Hair samples from rub stations could be used to provide estimates of abundance, measures of genetic diversity and health, and detection-nondetection data useful for cost-effective population monitoring.

Smart location system; Sistema de localizacao inteligente Smart Location System

Energy Technology Data Exchange (ETDEWEB)

Silva, Jose Augusto Pereira da; Antunes, Rodrigo de Castro; Azevedo, Fabio Augusto Ferreira de [PipeWay Engenharia, Rio de Janeiro, RJ (Brazil); Afonso, Orlando de Jesus Ribeiro [Instituto de Pesquisas da Marinha, Rio de Janeiro, RJ (Brazil); Matsuura, Minoru; Santa Cruz, Sergio de Freitas [TRANSPETRO - PETROBRAS Transportes, Rio de Janeiro, RJ (Brazil); Santos, Jose Alberto Costa dos; Hashiguchi, Decio Issao [GDK Engenharia (Brazil)

2003-07-01

This paper describes the technology used in the Intelligent Location System developed by Pipeway and includes some of the results already obtained optimizing repair time and logistic costs during the location of anomalies detected by intelligent pigs, a joint operation within the scope of the contract for Sub sea Pipeline Recovery in the Guanabara Bay with PETROBRAS/TRANSPETRO and GDK Engenharia. The system uses the ELF (Extra Low Frequency) transmission and reception technology at points near a pipe, with or without concrete coating, whose signals are recorded in the inspection tool memory to accurately establish reference points, thus preventing excessive dig work or dredging when human and operational risks tend to be high. (author)

30 CFR 90.201 - Sampling; general requirements.

Science.gov (United States)

2010-07-01

... operational during the entire shift or for 8 hours, whichever time is less. (c) Upon request from the District... respirable dust samples of the concentration of respirable dust in the active workings of the mine as... of the normal working position; or (3) At a location that represents the maximum concentration of...

Continuous wavelet transform analysis and modal location analysis acoustic emission source location for nuclear piping crack growth monitoring

Energy Technology Data Exchange (ETDEWEB)

Mohd, Shukri [Nondestructive Testing Group, Industrial Technology Division, Malaysian Nuclear Agency, 43000, Bangi, Selangor (Malaysia); Holford, Karen M.; Pullin, Rhys [Cardiff School of Engineering, Cardiff University, Queen' s Buildings, The Parade, CARDIFF CF24 3AA (United Kingdom)

2014-02-12

Source location is an important feature of acoustic emission (AE) damage monitoring in nuclear piping. The ability to accurately locate sources can assist in source characterisation and early warning of failure. This paper describe the development of a novelAE source location technique termed 'Wavelet Transform analysis and Modal Location (WTML)' based on Lamb wave theory and time-frequency analysis that can be used for global monitoring of plate like steel structures. Source location was performed on a steel pipe of 1500 mm long and 220 mm outer diameter with nominal thickness of 5 mm under a planar location test setup using H-N sources. The accuracy of the new technique was compared with other AE source location methods such as the time of arrival (TOA) techniqueand DeltaTlocation. Theresults of the study show that the WTML method produces more accurate location resultscompared with TOA and triple point filtering location methods. The accuracy of the WTML approach is comparable with the deltaT location method but requires no initial acoustic calibration of the structure.

Continuous wavelet transform analysis and modal location analysis acoustic emission source location for nuclear piping crack growth monitoring

International Nuclear Information System (INIS)

Shukri Mohd

2013-01-01

Full-text: Source location is an important feature of acoustic emission (AE) damage monitoring in nuclear piping. The ability to accurately locate sources can assist in source characterisation and early warning of failure. This paper describe the development of a novelAE source location technique termed Wavelet Transform analysis and Modal Location (WTML) based on Lamb wave theory and time-frequency analysis that can be used for global monitoring of plate like steel structures. Source location was performed on a steel pipe of 1500 mm long and 220 mm outer diameter with nominal thickness of 5 mm under a planar location test setup using H-N sources. The accuracy of the new technique was compared with other AE source location methods such as the time of arrival (TOA) technique and DeltaTlocation. The results of the study show that the WTML method produces more accurate location results compared with TOA and triple point filtering location methods. The accuracy of the WTML approach is comparable with the deltaT location method but requires no initial acoustic calibration of the structure. (author)

Continuous wavelet transform analysis and modal location analysis acoustic emission source location for nuclear piping crack growth monitoring

International Nuclear Information System (INIS)

Mohd, Shukri; Holford, Karen M.; Pullin, Rhys

2014-01-01

Source location is an important feature of acoustic emission (AE) damage monitoring in nuclear piping. The ability to accurately locate sources can assist in source characterisation and early warning of failure. This paper describe the development of a novelAE source location technique termed 'Wavelet Transform analysis and Modal Location (WTML)' based on Lamb wave theory and time-frequency analysis that can be used for global monitoring of plate like steel structures. Source location was performed on a steel pipe of 1500 mm long and 220 mm outer diameter with nominal thickness of 5 mm under a planar location test setup using H-N sources. The accuracy of the new technique was compared with other AE source location methods such as the time of arrival (TOA) techniqueand DeltaTlocation. Theresults of the study show that the WTML method produces more accurate location resultscompared with TOA and triple point filtering location methods. The accuracy of the WTML approach is comparable with the deltaT location method but requires no initial acoustic calibration of the structure

Indoor Positioning with Radio Location Fingerprinting

DEFF Research Database (Denmark)

Kjærgaard, Mikkel Baun

. A promising indoor positioning technique is radio-based location ngerprinting, having the major advantage of exploiting already existing radio infrastructures, like IEEE 802.11 or GSM, which avoids extra deployment costs and eort. The research goal of this thesis is to address the limitations of current...... indoor location ngerprinting systems. In particular the aim is to advance location ngerprinting techniques for the challenges of handling heterogeneous clients, scalability to many clients, and interference between communication and positioning. The wireless clients used for location ngerprinting...... are heterogeneous even when only considering clients for the same technology. The heterogeneity is due to dierent radios, antennas, and rmwares causing measurements for location ngerprinting not to be directly comparable among clients. Heterogeneity is a challenge for location ngerprinting because it severely...

Development of a sample chamber for micro-PIXE

International Nuclear Information System (INIS)

Kurosawa, M.; Sueno, S.; Shima, K.; Ohshima, H.; Ishii, H.; Kamiya, H.; Kimoto, S.

1997-01-01

A new sample chamber for micro-PIXE analysis of geological thick samples has been successfully developed. A target in the sample chamber is normal to the beam and Si(Li) detectors are located at 135deg to the beam direction. For the sample observation, a normal viewing optics with the optical axis collinear with the beam is achieved by a combination of long working distance microscope and mirror with a central hole for the beam transmission. The normal incidence beam and normal viewing are essential to raise a spatial resolution of the thick target analysis. In addition, the sample chamber has fulfilled ten requirements as for material, driving stage, X-ray absorbers, space for another detector, etc. The information obtained by the development can give a new guide to manufacture the sample chamber for the micro-PIXE. (author)

A Calculus of Located Entities

Directory of Open Access Journals (Sweden)

Adriana Compagnoni

2014-03-01

Full Text Available We define BioScapeL, a stochastic pi-calculus in 3D-space. A novel aspect of BioScapeL is that entities have programmable locations. The programmer can specify a particular location where to place an entity, or a location relative to the current location of the entity. The motivation for the extension comes from the need to describe the evolution of populations of biochemical species in space, while keeping a sufficiently high level description, so that phenomena like diffusion, collision, and confinement can remain part of the semantics of the calculus. Combined with the random diffusion movement inherited from BioScape, programmable locations allow us to capture the assemblies of configurations of polymers, oligomers, and complexes such as microtubules or actin filaments. Further new aspects of BioScapeL include random translation and scaling. Random translation is instrumental in describing the location of new entities relative to the old ones. For example, when a cell secretes a hydronium ion, the ion should be placed at a given distance from the originating cell, but in a random direction. Additionally, scaling allows us to capture at a high level events such as division and growth; for example, daughter cells after mitosis have half the size of the mother cell.

Directions in locational conflict research: Voting on the location of nuclear waste disposal facilities

International Nuclear Information System (INIS)

Shelley, F.M.; Murauskas, G.T.

1985-01-01

It is clear from empirical evidence that currently significant locational conflicts concerning the siting of nuclear waste disposal facilities cannot be modeled under the standard noxious facility location paradigm that views locational conflict as conflict between regions. Rather, local populations are characterized by sharp disagreements as to whether the proposed facility is in fact salutary or noxious. Thus, conflict concerning nuclear waste disposal must be understood as a conflict among preferences and values, rather than among competing, areally defined interest groups. This has significant implications for the outcomes of political processes leading to siting decisions, as indicated in this paper. Whether intransivity occurs depends on the location and proportion of persons with different preference orderings concerning possible outcomes. Further research on this issue can and should be directed to further mathematical specification of these conditions along with empirical analysis where appropriate

Data Validation Package November 2015 Groundwater and Surface Water Sampling at the Old and New Rifle, Colorado, Processing Sites February 2016

Energy Technology Data Exchange (ETDEWEB)

Bush, Richard [USDOE Office of Legacy Management, Washington, DC (United States); Lemke, Peter [Navarro Research and Engineering, Inc., Oak Ridge, TN (United States)

2016-02-01

Water samples were collected from 36 locations at New Rifle and Old Rifle, Colorado, Processing Sites. Duplicate samples were collected from New Rifle locations 0659 and 0855, and Old Rifle location 0304. One equipment blank was collected after decontamination of non-dedicated equipment used to collect one surface water sample. Sampling and analyses were conducted as specified in the Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated). New Rifle Site Samples were collected at the New Rifle site from 16 monitoring wells and 7 surface locations in compliance with the December 2008 Groundwater Compliance Action Plan [GCAP] for the New Rifle, Colorado, Processing Site (LMS/RFN/S01920), with one exception: New Rifle location 0635 could not be sampled because it was inaccessible; a fence installed by the Colorado Department of Transportation prevents access to this location. DOE is currently negotiating access with the Colorado Department of Transportation. Analytes measured at the New Rifle site included contaminants of concern (COCs) (arsenic, molybdenum, nitrate + nitrite as nitrogen, selenium, uranium, and vanadium) ammonia as nitrogen, major cations, and major anions. Field measurements of total alkalinity, oxidation- reduction potential, pH, specific conductance, turbidity, and temperature were made at each location, and the water level was measured at each sampled well. A proposed alternate concentration limit (ACL) for vanadium of 50 milligrams per liter (mg/L), specific to the compliance (POC) wells (RFN-0217, -0659, -0664, and -0669) is included in the New Rifle GCAP. Vanadium concentrations in the POC wells were below the proposed ACL as shown in the time-concentration graphs in the Data Presentation section (Attachment 2). Time-concentration graphs from all other locations sampled are also included in Attachment 2. Sampling location RFN-0195 was misidentified for the June/August 2014

Discordance between location of positive cores in biopsy and location of positive surgical margin following radical prostatectomy.

Science.gov (United States)

Kim, Ji Won; Park, Hyoung Keun; Kim, Hyeong Gon; Ham, Dong Yeub; Paick, Sung Hyun; Lho, Yong Soo; Choi, Woo Suk

2015-10-01

We compared location of positive cores in biopsy and location of positive surgical margin (PSM) following radical prostatectomy. This retrospective analysis included patients who were diagnosed as prostate cancer by standard 12-core transrectal ultrasonography guided prostate biopsy, and who have PSM after radical prostatectomy. After exclusion of number of biopsy cores location data, 46 patients with PSM were identified. Locations of PSM in pathologic specimen were reported as 6 difference sites (apex, base and lateral in both sides). Discordance of biopsy result and PSM was defined when no positive cores in biopsy was identified at the location of PSM. Most common location of PSM were right apex (n=21) and left apex (n=15). Multiple PSM was reported in 21 specimens (45.7%). In 32 specimens (69.6%) with PSM, one or more concordant positive biopsy cores were identified, but 14 specimens (28%) had no concordant biopsy cores at PSM location. When discordant rate was separated by locations of PSM, right apex PSM had highest rate of discordant (38%). The discordant group had significantly lower prostate volume and lower number of positive cores in biopsy than concordant group. This study showed that one fourth of PSM occurred at location where tumor was not detected at biopsy and that apex PSM had highest rate of discordant. Careful dissection to avoid PSM should be performed in every location, including where tumor was not identified in biopsy.

Microfluidic ultrasonic particle separators with engineered node locations and geometries

Science.gov (United States)

Rose, Klint A.; Fisher, Karl A.; Wajda, Douglas A.; Mariella, Jr., Raymond P.; Bailey, Christopher; Dehlinger, Dietrich; Shusteff, Maxim; Jung, Byoungsok; Ness, Kevin D.

2016-04-26

An ultrasonic microfluidic system includes a separation channel for conveying a sample fluid containing small particles and large particles, flowing substantially parallel, adjacent to a recovery fluid, with which it is in contact. An acoustic transducer produces an ultrasound standing wave, that generates a pressure field having at least one node of minimum pressure amplitude. An acoustic extension structure is located proximate to said separation channel for positioning said acoustic node off center in said acoustic area and concentrating the large particles in said recovery fluid stream.

Legacy sample disposition project. Volume 2: Final report

International Nuclear Information System (INIS)

Gurley, R.N.; Shifty, K.L.

1998-02-01

This report describes the legacy sample disposition project at the Idaho Engineering and Environmental Laboratory (INEEL), which assessed Site-wide facilities/areas to locate legacy samples and owner organizations and then characterized and dispositioned these samples. This project resulted from an Idaho Department of Environmental Quality inspection of selected areas of the INEEL in January 1996, which identified some samples at the Test Reactor Area and Idaho Chemical Processing Plant that had not been characterized and dispositioned according to Resource Conservation and Recovery Act (RCRA) requirements. The objective of the project was to manage legacy samples in accordance with all applicable environmental and safety requirements. A systems engineering approach was used throughout the project, which included collecting the legacy sample information and developing a system for amending and retrieving the information. All legacy samples were dispositioned by the end of 1997. Closure of the legacy sample issue was achieved through these actions

Geostatistical integration and uncertainty in pollutant concentration surface under preferential sampling

Directory of Open Access Journals (Sweden)

Laura Grisotto

2016-04-01

Full Text Available In this paper the focus is on environmental statistics, with the aim of estimating the concentration surface and related uncertainty of an air pollutant. We used air quality data recorded by a network of monitoring stations within a Bayesian framework to overcome difficulties in accounting for prediction uncertainty and to integrate information provided by deterministic models based on emissions meteorology and chemico-physical characteristics of the atmosphere. Several authors have proposed such integration, but all the proposed approaches rely on representativeness and completeness of existing air pollution monitoring networks. We considered the situation in which the spatial process of interest and the sampling locations are not independent. This is known in the literature as the preferential sampling problem, which if ignored in the analysis, can bias geostatistical inferences. We developed a Bayesian geostatistical model to account for preferential sampling with the main interest in statistical integration and uncertainty. We used PM10 data arising from the air quality network of the Environmental Protection Agency of Lombardy Region (Italy and numerical outputs from the deterministic model. We specified an inhomogeneous Poisson process for the sampling locations intensities and a shared spatial random component model for the dependence between the spatial location of monitors and the pollution surface. We found greater predicted standard deviation differences in areas not properly covered by the air quality network. In conclusion, in this context inferences on prediction uncertainty may be misleading when geostatistical modelling does not take into account preferential sampling.

Predictors of locating women six to eight years after contact: internet resources at recruitment may help to improve response rates in longitudinal research

Directory of Open Access Journals (Sweden)

Gignac Monique AM

2007-06-01

Full Text Available Abstract Background The ability to locate those sampled has important implications for response rates and thus the success of survey research. The purpose of this study was to examine predictors of locating women requiring tracing using publicly available methods (primarily Internet searches, and to determine the additional benefit of vital statistics linkages. Methods Random samples of women aged 65–89 years residing in two regions of Ontario, Canada were selected from a list of those who completed a questionnaire between 1995 and 1997 (n = 1,500. A random sample of 507 of these women had been searched on the Internet as part of a feasibility pilot in 2001. All 1,500 women sampled were mailed a newsletter and information letter prior to recruitment by telephone in 2003 and 2004. Those with returned mail or incorrect telephone number(s required tracing. Predictors of locating women were examined using logistic regression. Results Tracing was required for 372 (25% of the women sampled, and of these, 181 (49% were located. Predictors of locating women were: younger age, residing in less densely populated areas, having had a web-search completed in 2001, and listed name identified on the Internet prior to recruitment in 2003. Although vital statistics linkages to death records subsequently identified 41 subjects, these data were incomplete. Conclusion Prospective studies may benefit from using Internet resources at recruitment to determine the listed names for telephone numbers thereby facilitating follow-up tracing and improving response rates. Although vital statistics linkages may help to identify deceased individuals, these may be best suited for post hoc response rate adjustment.

UMTRA Project water sampling and analysis plan, Salt Lake City, Utah. Revision 1

International Nuclear Information System (INIS)

1995-06-01

This water sampling and analysis plan describes planned, routine ground water sampling activities at the US Department of Energy Uranium Mill Tailings Remedial Action Project site in Salt Lake City, Utah. This plan identifies and justifies sampling locations, analytical parameters, detection limits, and sampling frequencies for routine monitoring of ground water, sediments, and surface waters at monitoring stations on the site

Location verification algorithm of wearable sensors for wireless body area networks.

Science.gov (United States)

Wang, Hua; Wen, Yingyou; Zhao, Dazhe

2018-01-01

Knowledge of the location of sensor devices is crucial for many medical applications of wireless body area networks, as wearable sensors are designed to monitor vital signs of a patient while the wearer still has the freedom of movement. However, clinicians or patients can misplace the wearable sensors, thereby causing a mismatch between their physical locations and their correct target positions. An error of more than a few centimeters raises the risk of mistreating patients. The present study aims to develop a scheme to calculate and detect the position of wearable sensors without beacon nodes. A new scheme was proposed to verify the location of wearable sensors mounted on the patient's body by inferring differences in atmospheric air pressure and received signal strength indication measurements from wearable sensors. Extensive two-sample t tests were performed to validate the proposed scheme. The proposed scheme could easily recognize a 30-cm horizontal body range and a 65-cm vertical body range to correctly perform sensor localization and limb identification. All experiments indicate that the scheme is suitable for identifying wearable sensor positions in an indoor environment.

Location Based Services and Applications

OpenAIRE

Elenis Gorrita Michel; Rónier Sierra Dávila; Samuel Montejo Sánchez

2012-01-01

Location Based Services (LBS) continue to grow in popularity, effectiveness and reliability, to the extent that applications are designed and implemented taking into account the facilities of the user location information. In this work, some of the main applications are addressed, in order to make an assessment of the current importance of the LBS, as a branch of technology in full swing. In addition, the main techniques for location estimation are studied, essential information to the LBS. B...

Assessment of long-term gas sampling design at two commercial manure-belt layer barns.

Science.gov (United States)

Chai, Li-Long; Ni, Ji-Qin; Chen, Yan; Diehl, Claude A; Heber, Albert J; Lim, Teng T

2010-06-01

Understanding temporal and spatial variations of aerial pollutant concentrations is important for designing air quality monitoring systems. In long-term and continuous air quality monitoring in large livestock and poultry barns, these systems usually use location-shared analyzers and sensors and can only sample air at limited number of locations. To assess the validity of the gas sampling design at a commercial layer farm, a new methodology was developed to map pollutant gas concentrations using portable sensors under steady-state or quasi-steady-state barn conditions. Three assessment tests were conducted from December 2008 to February 2009 in two manure-belt layer barns. Each barn was 140.2 m long and 19.5 m wide and had 250,000 birds. Each test included four measurements of ammonia and carbon dioxide concentrations at 20 locations that covered all operating fans, including six of the fans used in the long-term sampling that represented three zones along the lengths of the barns, to generate data for complete-barn monitoring. To simulate the long-term monitoring, gas concentrations from the six long-term sampling locations were extracted from the 20 assessment locations. Statistical analyses were performed to test the variances (F-test) and sample means (t test) between the 6- and 20-sample data. The study clearly demonstrated ammonia and carbon dioxide concentration gradients that were characterized by increasing concentrations from the west to east ends of the barns following the under-cage manure-belt travel direction. Mean concentrations increased from 7.1 to 47.7 parts per million (ppm) for ammonia and from 2303 to 3454 ppm for carbon dioxide from the west to east of the barns. Variations of mean gas concentrations were much less apparent between the south and north sides of the barns, because they were 21.2 and 20.9 ppm for ammonia and 2979 and 2951 ppm for carbon dioxide, respectively. The null hypotheses that the variances and means between the 6- and 20

78 FR 79009 - Proposed Information Collection; Radiation Sampling and Exposure Records (Pertains to Underground...

Science.gov (United States)

2013-12-27

... soliciting comments concerning the proposed information collection for updating Radiation Sampling and... exposed with no adverse effects have been established and are expressed as working levels (WL). The... mandatory samplings. Records must include the sample date, location, and results, and must be retained at...

Location, Location, Location: How Would a High-Performing Charter School Network Fare in Different States?

Science.gov (United States)

Lozier, Chris; Rotherham, Andrew J.

2011-01-01

In this paper the authors do not examine different operating strategies for charter schools or analyze the impact of their often educationally intensive models on finance. Instead, because public charter schools are funded predominantly by public dollars, they simply ask what impact location--and its associated variances in public funding and the…

About condition of soil ground at locations of the former Azgir nuclear test site

International Nuclear Information System (INIS)

Akhmetov, E.Z.; Adymov, Zh.I.; Ermatov, A.S.

2003-01-01

Full text: Soil condition after underground nuclear explosions at locations of the test sites is considered. The region is situated in the zone of northern deserts and characterized by prevalence of greyish-brown soils in conditions of sharply continental climate and presence of salt in soil-formative complex including tertiary clays, loess-like loam, loam sands and sands. There are small quantity of humus in such soil. During investigation of soil characteristics and ability of soil particles to form conglomerates, possessing of different properties, it is necessary to know both element and phase composition, determining, in the most extent, such physical and mechanical macro-characteristics as: density, stickiness, air and water penetrability, solubility, chemical resistance, granulometric set and others. Phase composition of soil samples can be, to a sufficient extent, determined by the X-ray diffractometry methods using ordinary X-ray experimental facilities. Phase composition of soil includes gypsum, quartz, calcium, potash feldspar hematite, kaolin, peach and mica in different quantities. Data on element composition of soil samples were obtained from the territory of technological locations of test site using the method of X-ray-fluorescent analysis. Granulometric composition of soil ground has been investigated using the methods of dry sieving and wet sieving for determination of radionuclide distribution in different fractions of soil particles. By the method of the dry sieving of soil ground samples there are taken place a sticking the small together of fine fractions and an adhesion of stuck-together particles to more large ones. Therefore, fine fractions cannot be separate completely at dry sieving. As distinct from the dry sieving an use of water jet in the sieving allows to overcome defects of the dry method and, by a sufficiently effective separation of granulometric fractions, to obtain more precise results of investigations of granulometric

Design of a groundwater sampling network for Minnesota

International Nuclear Information System (INIS)

Kanivetsky, R.

1977-01-01

This folio was compiled to facilitate the use of groundwater as a sampling medium to aid in exploration for hitherto undiscovered deposits of uranium in the subsurface rocks of Minnesota. The report consists of the following sheets of the hydrogeologic map of Minnesota: (1) map of bedrock hydrogeology, (2) generalized cross sections of the hydrogeologic map of Minnesota, showing both Quaternary deposits and bedrock, (3) map of waterwells that penetrate Precambrian rocks in Minnesota. A list of these wells, showing locations, names of owners, type of Precambrian aquifers penetrated, lithologic material of the aquifers, and well depths is provided in the appendix to this report. Structural settings, locations, and composition of the bedrock aquifers, movement of groundwater, and preliminary suggestions for a sampling program are discussed below under the heading Bedrock Hydrogeology of Minnesota. The map sheet showing Quaternary hydrogeology is not included in this report because the chemistry of groundwater in these deposits is not directly related to bedrock mineralization

Remote sampling and analysis of highly radioactive samples in shielded boxes

International Nuclear Information System (INIS)

Kirpikov, D.A.; Miroshnichenko, I.V.; Pykhteev, O.Yu.

2010-01-01

The sampling procedure used for highly radioactive coolant water is associated with high risk of personnel irradiation and uncontrolled radioactive contamination. Remote sample manipulation with provision for proper radiation shielding is intended for safety enhancement of the sampling procedure. The sampling lines are located in an isolated compartment, a shielded box. Various equipment which enables remote or automatic sample manipulation is used for this purpose. The main issues of development of the shielded box equipment intended for a wider ranger of remote chemical analyses and manipulation techniques for highly radioactive water samples are considered in the paper. There were three principal directions of work: Transfer of chemical analysis performed in the laboratory inside the shielded box; Prevalence of computer-aided and remote techniques of highly radioactive sample manipulation inside the shielded box; and, Increase in control over sampling and determination of thermal-hydraulic parameters of the coolant water in the sampling lines. The developed equipment and solutions enable remote chemical analysis in the restricted volume of the shielded box by using ion-chromatographic, amperometrical, fluorimetric, flow injection, phototurbidimetric, conductometric and potentiometric methods. Extent of control performed in the shielded box is determined taking into account the requirements of the regulatory documents as well as feasibility and cost of the technical adaptation of various methods to the shielded box conditions. The work resulted in highly precise determination of more than 15 indexes of the coolant water quality performed in on-line mode in the shielded box. It averages to 80% of the total extent of control performed at the prototype reactor plants. The novel solutions for highly radioactive sample handling are implemented in the shielded box (for example, packaging, sample transportation to the laboratory, volume measurement). The shielded box is

Simulation analysis for hyperbola locating accuracy

International Nuclear Information System (INIS)

Wang Changli; Liu Daizhi

2004-01-01

In the system of the hyperbola location, the geometric shape of the detecting stations has an important influence on the locating accuracy. At first, this paper simulates the process of the hyperbola location by the computer, and then analyzes the influence of the geometric shape on the locating errors and gives the computer simulation results, finally, discusses the problems that require attention in course of selecting the detecting station. The conclusion has practicality. (authors)

What Sets the Radial Locations of Warm Debris Disks?

Energy Technology Data Exchange (ETDEWEB)

Ballering, Nicholas P.; Rieke, George H.; Su, Kate Y. L.; Gáspár, András, E-mail: ballerin@email.arizona.edu [Steward Observatory, University of Arizona, 933 North Cherry Avenue, Tucson, AZ 85721 (United States)

2017-08-20

The architectures of debris disks encode the history of planet formation in these systems. Studies of debris disks via their spectral energy distributions (SEDs) have found infrared excesses arising from cold dust, warm dust, or a combination of the two. The cold outer belts of many systems have been imaged, facilitating their study in great detail. Far less is known about the warm components, including the origin of the dust. The regularity of the disk temperatures indicates an underlying structure that may be linked to the water snow line. If the dust is generated from collisions in an exo-asteroid belt, the dust will likely trace the location of the water snow line in the primordial protoplanetary disk where planetesimal growth was enhanced. If instead the warm dust arises from the inward transport from a reservoir of icy material farther out in the system, the dust location is expected to be set by the current snow line. We analyze the SEDs of a large sample of debris disks with warm components. We find that warm components in single-component systems (those without detectable cold components) follow the primordial snow line rather than the current snow line, so they likely arise from exo-asteroid belts. While the locations of many warm components in two-component systems are also consistent with the primordial snow line, there is more diversity among these systems, suggesting additional effects play a role.

Failure analysis of burst tested fuel tube samples

International Nuclear Information System (INIS)

Padmaprabu, C.; Ramana Rao, S.V.; Srivatsava, R.K.

2005-01-01

The Total Circumferential Elongation (TCE) is an important parameter for evaluation of ductility of the Zircaloy-4 fuel tubes for the PHWR reactors. The TCE values of the fuel tubes were obtained using the burst testing technique. In some lots there is a variation in the values of the TCE. To investigate the reasons for such a large variation in the TCE, samples were selected at appropriate intervals and sectioned at the fractured portion. The surface morphology of the fractured surfaces was examined under Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectrometer (EDS). The morphologies show segregation of elements at specific locations. Energy dispersive spectra was obtained from those segregated particles. According to the magnitude of TCE value the samples were classified into low, intermediate and high ductility. Low ductility samples were found to contain large amount of segregations along the thickness direction of the tube. This forms a brittle region and a path for the easy crack growth along thickness direction. In the case of intermediate samples the segregation occurred in fewer locations compared to low ductile samples and also confined to the circumferential direction of the outside surface of the tube. Due to this, probability of crack formation at the surface of the tube could be high. But crack growth would be slower in the ductile matrix along the thickness direction resulting in the enhancement of TCE value compared to the low ductile sample. In the high ductile samples, the segregations were very scarce and found to be isolated and embedded in the ductile matrix. The mode of failure in these types of samples was found to be purely ductile. Cracks were found to originate solely from the micro voids in the material. As the probability of crack formation and its propagation is low, very high TCE values were observed in these samples. Microstructural observations of fractured surfaces and EDAX analysis was able to identify the

Reliability in the Location of Hindlimb Motor Representations in Fischer-344 Rats

Science.gov (United States)

Frost, Shawn B.; Iliakova, Maria; Dunham, Caleb; Barbay, Scott; Arnold, Paul; Nudo, Randolph J.

2014-01-01

Object The purpose of the present study was to determine the feasibility of using a common laboratory rat strain for locating cortical motor representations of the hindlimb reliably. Methods Intracortical Microstimulation (ICMS) techniques were used to derive detailed maps of the hindlimb motor representations in six adult Fischer-344 rats. Results The organization of the hindlimb movement representation, while variable across individuals in topographic detail, displayed several commonalities. The hindlimb representation was positioned posterior to the forelimb motor representation and postero-lateral to the motor trunk representation. The areal extent of the hindlimb representation across the cortical surface averaged 2.00 +/− 0.50 mm2. Superimposing individual maps revealed an overlapping area measuring 0.35 mm2, indicating that the location of the hindlimb representation can be predicted reliably based on stereotactic coordinates. Across the sample of rats, the hindlimb representation was found 1.25–3.75 mm posterior to Bregma, with an average center location ~ 2.6 mm posterior to Bregma. Likewise, the hindlimb representation was found 1–3.25 mm lateral to the midline, with an average center location ~ 2 mm lateral to midline. Conclusions The location of the cortical hindlimb motor representation in Fischer-344 rats can be reliably located based on its stereotactic position posterior to Bregma and lateral to the longitudinal skull suture at midline. The ability to accurately predict the cortical localization of functional hindlimb territories in a rodent model is important, as such animal models are being used increasingly in the development of brain-computer interfaces for restoration of function after spinal cord injury. PMID:23725395

ICE Online Detainee Locator System

Data.gov (United States)

Department of Homeland Security — The Online Detainee Locator datasets provide the location of a detainee who is currently in ICE custody, or who was release from ICE custody for any reason with the...

Duality in constrained location problems

DEFF Research Database (Denmark)

Juel, Henrik; Love, Robert F.

1987-01-01

The dual of a facility location problem with general norms, distance constraints, and linear constraints is formulated.......The dual of a facility location problem with general norms, distance constraints, and linear constraints is formulated....

Location and activity specific site-management for military locations

NARCIS (Netherlands)

Maring, L.; Hulst, M. van; Meuken, D.

2009-01-01

pace is limited in the Netherlands and military activities, that may cause nuisance or environmental hazards, should therefore be considered and evaluated during the use of military locations. The last few years TNO and Deltares have worked on a research program on environmental effects due to

Determination of {sup 90}Sr, {sup 63}Ni and {sup 55}Fe activities by liquid scintillation counting in the environmental samples close to French nuclear power plants located on Loire and Garonne rivers

Energy Technology Data Exchange (ETDEWEB)

Rousseau, G.; Mokili, M.B.; Le Roy, C.; Deniau, I. [SUBATECH, IN2P3 (France); Gontier, G.; Boyer, C. [EDF-DPI-DIN-CIDEN (France); Hemidy, P.Y. [EDF-DPN-UNIE-GPRE-IEV (France); Chardon, P. [CNRS/IN2P3 (France)

2014-07-01

The protection of the aquatic and terrestrial environment from a wide range of radioactive contaminants released by nuclear industry requires continuous monitoring of radionuclides released into the environment. Specific measurement methods depending of the radionuclide are used to determinate this contribution. A lot of radionuclide can easily be measured at low level by gamma spectrometry, like {sup 137}Cs, {sup 60}Co..., but others like {sup 90}Sr, {sup 63}Ni or {sup 55}Fe require prior specific radiochemical separations. Activity of {sup 90}Sr values in environmental samples are available but only few measurements of {sup 63}Ni and {sup 55}Fe activities have been carried out in samples collected in the environment close to French nuclear power plants located on the Loire and Garonne rivers despite they represent 12% to 24% for {sup 63}Ni activity and <1% for {sup 55}Fe + other minor radionuclides of total activity of their liquid effluent discharges. {sup 90}Sr is not rejected by the liquid effluent discharges of Nuclear Power Plants and can be found in the environmental samples because of thermonuclear test and subsequently after the Chernobyl nuclear power plant accident. Considering the French Nuclear Power Plant located on Loire and Garonne rivers, the determination of {sup 90}Sr, {sup 63}Ni and {sup 55}Fe levels in the environmental samples around French nuclear power plants is carried out to detect the traces of these radionuclides originating from nuclear technology activities. The environment around five French nuclear Power Plants was investigated for 4 years between 2009 and 2014. The radionuclide activities determined by liquid scintillation counting after chemical steps were performed on a large set of various matrix samples likely to be encountered in environmental monitoring as soils, sediments, terrestrial and aquatic bio-indicators. It was found that the mean activity concentration of the most frequently detected was for the radionuclide {sup 90

Bounds in the location-allocation problem

DEFF Research Database (Denmark)

Juel, Henrik

1981-01-01

Develops a family of stronger lower bounds on the objective function value of the location-allocation problem. Solution methods proposed to solve problems in location-allocation; Efforts to develop a more efficient bound solution procedure; Determination of the locations of the sources....

Characterization of polycyclic aromatic hydrocarbons (PAH's) present in sampled cooked food

International Nuclear Information System (INIS)

Palm Naa-Dedei, L.M.

2010-07-01

The study was conducted to determine the levels of Polycyclic Aromatic Hydrocarbons in the following traditionally prepared food: smoked and grilled Scomba japonicus, grilled meat (khebab) and bread sampled from some Ghanaian markets. By way of preparation of traditional food, some food comes into direct contact with smoke or extremely high temperature which are potential sources of Polycyclic Aromatic Hydrocarbon generation. Levels of 20 individual Polycyclic Aromatic Hydrocarbons including acenaphthene, acenaphtyelene, anthanthrene, anthracene, benz(a)anthracene, benzo(a)pyrene, benzo(b)fluoranthene, benzo(e)pyrene, benzo(ghi)perylene, benzo(j)fluoranthene, benzo(k)fluoranthene, chrysene, cyclopenta(cd)pyrene, dibenzo(ah)anthracene, fluoranthene, fluorene, indeno(1,2,3-cd)pyrene, naphthalene, phenanthrene and pyrene were determined in 11 smoked and 5 grilled fish, 4 grilled pieces of meat and 3 loaves of baked bread using gas chromatographic techniques with flame ionization detector. Benzo(a)pyrene, which is one of the few PAH for which a legal limit exists in different types of food matrices and other high molecular weight PAHs suspected to be carcinogenic have been detected in high concentrations in most samples. Bread samples gave mean polycyclic aromatic hydrocarbon concentrations of up to 20.39 μg/kg while khebab samples gave mean polycyclicaromatic hydrocarbon concentrations of up to 67.61 μg/kg. There was positive correlation of 0.987 between levels of polycyclic aromatic hydrocarbon concentrations in khebab samples from locations Osu and Atomic down. There was a positive correlation in the concentrations of the high molecular weight PAHs in all smoked fishes from four locations with values between 0.954 and 0.999 for the correlation between any two groups. The polycyclic aromatic hydrocarbon concentration determined in smoked fish samples deceased in terms of location according to the order Winneba > Madina > Chorkor > Ada.

AFRICOM: Does Location Matter?

Science.gov (United States)

2009-03-01

Decision Model,” 242-244. 26 Susan Hesse Owen & Mark S. Daskin , “Strategic Facility Location: A Review,” European Journal of Operational Research...Susan Hesse & Mark S. Daskin . “Strategic Facility Location: A Review,” European Journal of Operational Research 111 (1998), 423-447. Paye-Layeleh...ES) N/ A 10. SPONSORING/MONITORING AGENCY REPORT NUMBER 11. SUPPLEMENTARY NOTES The views expressed in this thesis are those of the author and

Heat Retreat Locations in Cities - The Survey-Based Location Analysis of Heat Relief

Science.gov (United States)

Neht, Alice; Maximini, Claudia; Prenger-Berninghoff, Kathrin

2017-12-01

The adaptation of cities to climate change effects is one of the major strategies in urban planning to encounter the challenges of climate change (IPCC 2014). One of the fields of climate change adaption is dealing with heat events that occur more frequently and with greater intensity. Cities in particular are vulnerable to these events due to high population and infrastructure density. Proceeding urbanization calls for the existence of sufficient heat retreat locations (HRL) to enable relief for the population from heat in summer. This is why an extensive analysis of HRL is needed. This paper aims at the development of a survey-based location analysis of heat relief by identifying user groups, locations and characteristics of HRL based on a home survey that was conducted in three German cities. Key results of the study show that the majority of the participants of the survey are users of existing HRL, are affected by heat, and perceive heat as a burden in summer. Moreover, HRL that are located in close proximity are preferred by most users while their effect depends on the regional context that has to be considered in the analysis. Hence, this research presents an approach to heat relief that underlines the importance of HRL in cities by referring to selected examples of HRL types in densely populated areas of cities. HRL should especially be established and secured in densely built-up areas of cities. According to results of the survey, most HRL are located in public spaces, and the overall accessibility of HRL turned out to be an issue.

It's All about Location, Location, Location: Children's Memory for the "Where'' of Personally Experienced Events

Science.gov (United States)

Bauer, Patricia J.; Doydum, Ayzit O.; Pathman, Thanujeni; Larkina, Marina; Guler, O. Evren; Burch, Melissa

2012-01-01

Episodic memory is defined as the ability to recall specific past events located in a particular time and place. Over the preschool and into the school years, there are clear developmental changes in memory for when events took place. In contrast, little is known about developmental changes in memory for where events were experienced. In the…

Multi-dimensional indoor location information model

NARCIS (Netherlands)

Xiong, Q.; Zhu, Q.; Zlatanova, S.; Huang, L.; Zhou, Y.; Du, Z.

2013-01-01

Aiming at the increasing requirements of seamless indoor and outdoor navigation and location service, a Chinese standard of Multidimensional Indoor Location Information Model is being developed, which defines ontology of indoor location. The model is complementary to 3D concepts like CityGML and

Location Privacy Techniques in Client-Server Architectures

DEFF Research Database (Denmark)

Jensen, Christian Søndergaard; Lu, Hua; Yiu, Man Lung

2009-01-01

A typical location-based service returns nearby points of interest in response to a user location. As such services are becoming increasingly available and popular, location privacy emerges as an important issue. In a system that does not offer location privacy, users must disclose their exact...... locations in order to receive the desired services. We view location privacy as an enabling technology that may lead to increased use of location-based services. In this chapter, we consider location privacy techniques that work in traditional client-server architectures without any trusted components other....... Third, their effectiveness is independent of the distribution of other users, unlike the k-anonymity approach. The chapter characterizes the privacy models assumed by existing techniques and categorizes these according to their approach. The techniques are then covered in turn according...

Using ArcMap, Google Earth, and Global Positioning Systems to select and locate random households in rural Haiti.

Science.gov (United States)

Wampler, Peter J; Rediske, Richard R; Molla, Azizur R

2013-01-18

A remote sensing technique was developed which combines a Geographic Information System (GIS); Google Earth, and Microsoft Excel to identify home locations for a random sample of households in rural Haiti. The method was used to select homes for ethnographic and water quality research in a region of rural Haiti located within 9 km of a local hospital and source of health education in Deschapelles, Haiti. The technique does not require access to governmental records or ground based surveys to collect household location data and can be performed in a rapid, cost-effective manner. The random selection of households and the location of these households during field surveys were accomplished using GIS, Google Earth, Microsoft Excel, and handheld Garmin GPSmap 76CSx GPS units. Homes were identified and mapped in Google Earth, exported to ArcMap 10.0, and a random list of homes was generated using Microsoft Excel which was then loaded onto handheld GPS units for field location. The development and use of a remote sensing method was essential to the selection and location of random households. A total of 537 homes initially were mapped and a randomized subset of 96 was identified as potential survey locations. Over 96% of the homes mapped using Google Earth imagery were correctly identified as occupied dwellings. Only 3.6% of the occupants of mapped homes visited declined to be interviewed. 16.4% of the homes visited were not occupied at the time of the visit due to work away from the home or market days. A total of 55 households were located using this method during the 10 days of fieldwork in May and June of 2012. The method used to generate and field locate random homes for surveys and water sampling was an effective means of selecting random households in a rural environment lacking geolocation infrastructure. The success rate for locating households using a handheld GPS was excellent and only rarely was local knowledge required to identify and locate households. This

Using ArcMap, Google Earth, and Global Positioning Systems to select and locate random households in rural Haiti

Directory of Open Access Journals (Sweden)

Wampler Peter J

2013-01-01

Full Text Available Abstract Background A remote sensing technique was developed which combines a Geographic Information System (GIS; Google Earth, and Microsoft Excel to identify home locations for a random sample of households in rural Haiti. The method was used to select homes for ethnographic and water quality research in a region of rural Haiti located within 9 km of a local hospital and source of health education in Deschapelles, Haiti. The technique does not require access to governmental records or ground based surveys to collect household location data and can be performed in a rapid, cost-effective manner. Methods The random selection of households and the location of these households during field surveys were accomplished using GIS, Google Earth, Microsoft Excel, and handheld Garmin GPSmap 76CSx GPS units. Homes were identified and mapped in Google Earth, exported to ArcMap 10.0, and a random list of homes was generated using Microsoft Excel which was then loaded onto handheld GPS units for field location. The development and use of a remote sensing method was essential to the selection and location of random households. Results A total of 537 homes initially were mapped and a randomized subset of 96 was identified as potential survey locations. Over 96% of the homes mapped using Google Earth imagery were correctly identified as occupied dwellings. Only 3.6% of the occupants of mapped homes visited declined to be interviewed. 16.4% of the homes visited were not occupied at the time of the visit due to work away from the home or market days. A total of 55 households were located using this method during the 10 days of fieldwork in May and June of 2012. Conclusions The method used to generate and field locate random homes for surveys and water sampling was an effective means of selecting random households in a rural environment lacking geolocation infrastructure. The success rate for locating households using a handheld GPS was excellent and only

Storing and accessing radioactivity data in environmental samples: the resources of GEORAD

Energy Technology Data Exchange (ETDEWEB)

Silva, Tadeu A. de A.; Gonzalez, Sergio de A.; Reis, Rocio G. dos; Vasconcellos, Luiza M. de H. e; Lauria, Dejanira de C., E-mail: tedsilva@ird.gov.br, E-mail: gonzalez@ird.gov.br, E-mail: rocio@ird.gov.br, E-mail: luiza@ird.gov.br, E-mail: dejanira@ird.gov.br [Isntituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

2013-07-01

A georeferenced information system of radioactivity in environmental samples, named GEORAD, was created with the goal of aggregating, storing and promoting the preservation of the data produced by Brazilian researches, and sharing with the research community a database on radioactivity in Brazil. The system provides information on concentrations of the natural series, cosmogenic and fall out radionuclides in samples of soil, water and food, among others, along with the geographical location of the samples. By this way, the location of the sample can be visualized on Brazilian map. A spreadsheet containing all the data and information about the sample can be also obtained. As a result, the database system can enable the available data to be exploited to the maximum potential for further research and allows new research on existing information. The system also provides reference information on where the data information were obtained, that enables data citation and linking data with publications to increase visibility and accessibility of data and the research itself. The GEORAD system has been continuously fed and updated, containing, currently, data from more than 2,000 samples. This paper presents the latest system updates and discusses its resources. (author)

Storing and accessing radioactivity data in environmental samples: the resources of GEORAD

International Nuclear Information System (INIS)

Silva, Tadeu A. de A.; Gonzalez, Sergio de A.; Reis, Rocio G. dos; Vasconcellos, Luiza M. de H. e; Lauria, Dejanira de C.

2013-01-01

A georeferenced information system of radioactivity in environmental samples, named GEORAD, was created with the goal of aggregating, storing and promoting the preservation of the data produced by Brazilian researches, and sharing with the research community a database on radioactivity in Brazil. The system provides information on concentrations of the natural series, cosmogenic and fall out radionuclides in samples of soil, water and food, among others, along with the geographical location of the samples. By this way, the location of the sample can be visualized on Brazilian map. A spreadsheet containing all the data and information about the sample can be also obtained. As a result, the database system can enable the available data to be exploited to the maximum potential for further research and allows new research on existing information. The system also provides reference information on where the data information were obtained, that enables data citation and linking data with publications to increase visibility and accessibility of data and the research itself. The GEORAD system has been continuously fed and updated, containing, currently, data from more than 2,000 samples. This paper presents the latest system updates and discusses its resources. (author)

FUNGI ISOLATED FROM GROUNDNUTS IN SOME LOCATIONS OF WEST JAVA

Directory of Open Access Journals (Sweden)

O.s. DHARMAPUTRA

1996-01-01

Full Text Available One hundred and ninety eight groundnut samples were collected from freshly harvested groundnuts (FHG, farmer storage systems (FSS, middlemen warehouses (MW, wholesalers (WS and retailer sample (RS during the dry and wet seasons from Cidolog, Cianjur, Sukabumi and Bogor, West Java, Indonesia, in 1990/1991. The moisture content (m.c., intactness of kernels, and the percentages of groundnut kernels infected by each species of fungi were analyzed. In genera, the m.c. of the samples collected during the dry season was lower than of those collected during the wet season. Also, the m.c. of samples collected from FHG, FSS and MW was higher than of those collected from WS and RS. The m.c. of samples collected from FHG was the highest (12.5-45.75%, but the percentages of damaged kernels were the lowest (2.5-13.8%, because the samples were shelled manually. A total of 25 species of fungi were isolated from samples collected from the 4 localities. They were Acremonium strictum, Aspergillus candidus, A. flavus, A. niger, A. ochraceus, A. tamarii, A. wentii, Botryodiplodia theobromae, Cladosporium cladosporioides, C. sphaerospermum, Eumtium chevalieri, E. repens, E. rubrum, Fusarium equiseti, F. longipes, F. oxysporum, F. semitectum, Mucor sp., Papulaspora sp., Pestalotia sp., Penicillium aethiopicum, P. citrinum, Rhizapus sp., R. stolonifer and Syncephalastrum sp. The predominant fungi in samples collected from Cidolog and Sukabumi during the dry season were Aspergillus wentii, while those collected from Cianjur and Bogor were A. niger. The percentages of kernels infected by A. wentii in samples collected from Cidolog and Sukabumi were between 30-100% and 36-100%, respectively, while those of kernels infected by A. nigerin samples collected from Cianjur and Bogor were between 34-93% and 14-98%, respectively. The predominant fungi in samples collected from each location during the wet season were A. flavus. The percentage of kernels infected by the fungus in

Superficially located enlarged lymphoid follicles characterise nodular gastritis.

Science.gov (United States)

Okamura, Takuma; Sakai, Yasuhiro; Hoshino, Hitomi; Iwaya, Yugo; Tanaka, Eiji; Kobayashi, Motohiro

2015-01-01

Nodular gastritis is a form of chronic Helicobacter pylori gastritis affecting the gastric antrum and characterised endoscopically by the presence of small nodular lesions resembling gooseflesh. It is generally accepted that hyperplasia of lymphoid follicles histologically characterises nodular gastritis; however, quantitative analysis in support of this hypothesis has not been reported. Our goal was to determine whether nodular gastritis is characterised by lymphoid follicle hyperplasia.The number, size, and location of lymphoid follicles in nodular gastritis were determined and those properties compared to samples of atrophic gastritis. The percentages of high endothelial venule (HEV)-like vessels were also evaluated.The number of lymphoid follicles was comparable between nodular and atrophic gastritis; however, follicle size in nodular gastritis was significantly greater than that seen in atrophic gastritis. Moreover, lymphoid follicles in nodular gastritis were positioned more superficially than were those in atrophic gastritis. The percentage of MECA-79 HEV-like vessels was greater in areas with gooseflesh-like lesions in nodular versus atrophic gastritis.Superficially located hyperplastic lymphoid follicles characterise nodular gastritis, and these follicles correspond to gooseflesh-like nodular lesions observed endoscopically. These observations suggest that MECA-79 HEV-like vessels could play at least a partial role in the pathogenesis of nodular gastritis.

Classification of Surface and Deep Soil Samples Using Linear Discriminant Analysis

International Nuclear Information System (INIS)

Wasim, M.; Ali, M.; Daud, M.

2015-01-01

A statistical analysis was made of the activity concentrations measured in surface and deep soil samples for natural and anthropogenic gamma-emitting radionuclides. Soil samples were obtained from 48 different locations in Gilgit, Pakistan covering about 50 km/sup 2/ areas at an average altitude of 1550 m above sea level. From each location two samples were collected: one from the top soil (2-6 cm) and another from a depth of 6-10 cm. Four radionuclides including /sup 226/Ra, /sup 232/Th, /sup 40/K and /sup 137/Cs were quantified. The data was analyzed using t-test to find out activity concentration difference between the surface and depth samples. At the surface, the median activity concentrations were 23.7, 29.1, 4.6 and 115 Bq kg/sup -1/ for 226Ra, 232Th, 137Cs and 40K respectively. For the same radionuclides, the activity concentrations were respectively 25.5, 26.2, 2.9 and 191 Bq kg/sup -1/ for the depth samples. Principal component analysis (PCA) was applied to explore patterns within the data. A positive significant correlation was observed between the radionuclides /sup 226/Ra and /sup 232/Th. The data from PCA was further utilized in linear discriminant analysis (LDA) for the classification of surface and depth samples. LDA classified surface and depth samples with good predictability. (author)

47 CFR 73.1120 - Station location.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Station location. 73.1120 Section 73.1120... Rules Applicable to All Broadcast Stations § 73.1120 Station location. Each AM, FM, TV and Class A TV... be the geographical station location. [65 FR 30003, May 10, 2000] ...

Permian Basin location recommendation report

International Nuclear Information System (INIS)

1983-09-01

Candidate study areas are screened from the Palo Duro and Dalhart Basin areas using data obtained from studies to date and criteria and specifications that consider: rock geometry; rock characteristics; human intrusion potential; surface characteristics; and environmental and socioeconomic conditions. Two preferred locations are recommended from among these areas for additional characterization to identify potential National Waste Terminal Storage (NWTS) salt repository sites. One location, in northeastern Deaf Smith County and southeastern Oldham County, is underlain by two salt units that meet the adopted screening specifications. The other location, in northcentral Swisher County, is underlain by one salt unit that meets the adopted screening specifications. Both locations have several favorable features, relative to surrounding areas, and no obviously undesirable characteristics. Both lie wholly on the Southern High Plains surface, are in relatively sparsely populated areas, contain no unique land use conflicts, and comprise large enough geographic areas to provide flexibility in site selection. Data gathered to date indicate that these locations contain salt units sufficient in thickness and in depth for the safe construction and operation of the underground facilities under consideration. 93 references, 34 figures, 6 tables

Web cache location

Directory of Open Access Journals (Sweden)

Boffey Brian

2004-01-01

Full Text Available Stress placed on network infrastructure by the popularity of the World Wide Web may be partially relieved by keeping multiple copies of Web documents at geographically dispersed locations. In particular, use of proxy caches and replication provide a means of storing information 'nearer to end users'. This paper concentrates on the locational aspects of Web caching giving both an overview, from an operational research point of view, of existing research and putting forward avenues for possible further research. This area of research is in its infancy and the emphasis will be on themes and trends rather than on algorithm construction. Finally, Web caching problems are briefly related to referral systems more generally.

Are ant assemblages of Brazilian veredas characterised by location or habitat type?

Science.gov (United States)

Costa-Milanez, C B; Lourenço-Silva, G; Castro, P T A; Majer, J D; Ribeiro, S P

2014-02-01

Wetland areas in the Brazilian Cerrado, known as "veredas", represent ecosystems formed on sandy soils with high concentrations of peat, and are responsible for the recharge of aquiferous reservoirs. They are currently under threat by various human activities, most notably the clearing of vegetation for Eucalyptus plantations. Despite their ecological importance and high conservation value, little is known about the actual effects of human disturbance on the animal community. To assess how habitat within different veredas, and plantations surrounding them affect ant assemblages, we selected four independent vereda locations, two being impacted by Eucalyptus monoculture (one younger and one mature plantation) and two controls, where the wetland was surrounded by cerrado vegetation. Ant sampling was conducted in May 2010 (dry season) using three complementary methods, namely baits, pitfall traps, and hand collection, in the wetland and in the surrounding habitats. A total of 7,575 ants were sampled, belonging to seven subfamilies, 32 genera and 124 species. Ant species richness and abundance did not differ between vereda locations, but did between the habitats. When impacted by the monoculture, ant species richness and abundance decreased in wetlands, but were less affected in the cerrado habitat. Ant species composition differed between the three habitats and between vereda locations. Eucalyptus plantations had an ant species composition defined by high dominance of Pheidole sp. and Solenopsis invicta, while natural habitats were defined by Camponotus and Crematogaster species. Atta sexdens was strictly confined to native habitats of non-impacted "veredas". Eucalyptus monocultures require high quantities of water in the early stages, which may have caused a decrease in groundwater level in the wetland, allowing hypogeic ants such as Labidus praedator to colonise this habitat.

A basis for customising perimetric locations within the macula in glaucoma.

Science.gov (United States)

Alluwimi, Muhammed S; Swanson, William H; Malinovsky, Victor E; King, Brett J

2018-03-01

It has been recognised that the 24-2 grid used for perimetry may poorly sample the macula, which has been recently identified as a critical region for diagnosing and managing patients with glaucoma. We compared data derived from patients and controls to investigate the efficacy of a basis for customising perimetric locations within the macula, guided by en face images of retinal nerve fibre layer (RNFL) bundles. We used SD-OCT en face montages (www.heidelbergengineering.com) of the RNFL in 10 patients with glaucoma (ages 56-80 years, median 67.5 years) and 30 age-similar controls (ages 47-77, median 58). These patients were selected because of either the absence of perimetric defect while glaucomatous damage to the RNFL bundles was observed, or because of perimetric defect that did not reflect the extent and locations of the glaucomatous damage that appeared in the RNFL images. We used a customised blob stimulus for perimetric testing (a Gaussian blob with 0.25° standard deviation) at 10-2 grid locations, to assess the correspondence between perimetric defects and damaged RNFL bundles observed on en face images and perimetric defects. Data from the age-similar controls were used to compute total deviation (TD) and pattern deviation (PD) values at each location; a perimetric defect for a location was defined as a TD or PD value of -0.5 log unit or deeper. A McNemar's test was used to compare the proportions of locations with perimetric defects that fell outside the damaged RNFL bundles, with and without accounting for displacement of ganglion cell bodies. All patients but one had perimetric defects that were consistent with the patterns of damaged RNFL bundles observed on the en face images. We found six abnormal perimetric locations of 2040 tested in controls and 132 abnormal perimetric locations of 680 tested in patients. The proportions of abnormal locations that fell outside the damaged RNFL bundles, with and without accounting for displacement of the

47 CFR 101.129 - Transmitter location.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Transmitter location. 101.129 Section 101.129... SERVICES Technical Standards § 101.129 Transmitter location. (a) The applicant must determine, prior to... adequate to render the service proposed. In cases of questionable antenna locations, it is desirable to...

Mining Significant Semantic Locations from GPS Data

DEFF Research Database (Denmark)

Cao, Xin; Cong, Gao; Jensen, Christian Søndergaard

2010-01-01

With the increasing deployment and use of GPS-enabled devices, massive amounts of GPS data are becoming available. We propose a general framework for the mining of semantically meaningful, significant locations, e.g., shopping malls and restaurants, from such data. We present techniques capable...... of extracting semantic locations from GPS data. We capture the relationships between locations and between locations and users with a graph. Significance is then assigned to locations using random walks over the graph that propagates significance among the locations. In doing so, mutual reinforcement between...

Mining significant semantic locations from GPS data

DEFF Research Database (Denmark)

Cao, Xin; Cong, Gao; Jensen, Christian S.

2010-01-01

With the increasing deployment and use of GPS-enabled devices, massive amounts of GPS data are becoming available. We propose a general framework for the mining of semantically meaningful, significant locations, e.g., shopping malls and restaurants, from such data. We present techniques capable...... of extracting semantic locations from GPS data. We capture the relationships between locations and between locations and users with a graph. Significance is then assigned to locations using random walks over the graph that propagates significance among the locations. In doing so, mutual reinforcement between...

FDI theories. A location-based approach

Directory of Open Access Journals (Sweden)

Popovici, Oana Cristina

2014-09-01

Full Text Available Given the importance of FDI for the economic growth of both home and host countries, the aim of this paper is to assess the importance granted to location advantages during the development of FDI theory. We start with the earliest theoretical directions as regards FDI location issues and extend our study to describing less debated theories, but of a particular importance for this theme. In this way, we have the opportunity to emphasize the changes in FDI location determinants. We find that a direction of the FDI theories’ expansion is due to the incorporation of new variables on location, although the location advantages are barely mentioned in the first explanations regarding the international activity of the firms.

Data Validation Package December 2015 Groundwater Sampling at the Ambrosia Lake, New Mexico, Disposal Site March 2016

Energy Technology Data Exchange (ETDEWEB)

Tsosie, Bernadette [USDOE Office of Legacy Management, Washington, DC (United States); Johnson, Dick [Navarro Research and Engineering, Inc., Oak Ridge, TN (United States)

2016-03-01

The Long-Term Surveillance Plan for the Ambrosia Lake, New Mexico, Disposal Site does not require groundwater monitoring because groundwater in the uppermost aquifer is of limited use, and supplemental standards have been applied to the aquifer. However, at the request of the New Mexico Environment Department, the U.S. Department of Energy conducts annual monitoring at three locations: monitoring wells 0409, 0675, and 0678. Sampling and analyses were conducted as specified in the Sampling and Analysis Plan for US. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated). Monitoring Well 0409 was not sampled during this event because it was dry. Water levels were measured at each sampled well. One duplicate sample was collected from location 0675. Groundwater samples from the two sampled wells were analyzed for the constituents listed in Table 1. Time-concentration graphs for selected analytes are included in this report. At well 0675, the duplicate results for total dissolved solids and for most metals (magnesium, molybdenum, potassium, selenium, sodium, and uranium) were outside acceptance criteria, which may indicate non-homogeneous conditions at this location. November 2014 results for molybdenum and uranium at well 0675 also were outside acceptance criteria. The well condition will be evaluated prior to the next sampling event.

Statistical sampling strategies for survey of soil contamination

NARCIS (Netherlands)

Brus, D.J.

2011-01-01

This chapter reviews methods for selecting sampling locations in contaminated soils for three situations. In the first situation a global estimate of the soil contamination in an area is required. The result of the surey is a number or a series of numbers per contaminant, e.g. the estimated mean

46 CFR 76.50-10 - Location.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Location. 76.50-10 Section 76.50-10 Shipping COAST GUARD... Extinguishers and Semiportable Fire Extinguishing Systems, Arrangements and Details § 76.50-10 Location. (a... fire extinguishing systems Classification (see § 76.50-5) Quantity and location Safety area 1...

A Compton scattering technique to determine wood density and locating defects in it

International Nuclear Information System (INIS)

Tondon, Akash; Sandhu, B. S.; Singh, Bhajan; Singh, Mohinder

2015-01-01

A Compton scattering technique is presented to determine density and void location in the given wooden samples. The technique uses a well collimated gamma ray beam from 137 Cs along with the NaI(Tl) scintillation detector. First, a linear relationship is established between Compton scattered intensity and known density of chemical compounds, and then density of the wood is determined from this linear relation. In another experiment, the ability of penetration of gamma rays is explored to detect voids in wooden (low Z) sample. The sudden reduction in the Compton scattered intensities agrees well with the position and size of voids in the wooden sample. It is concluded that wood density and the voids of size ∼ 4 mm and more can be detected easily by this method

SGA Project Locations

Data.gov (United States)

Vermont Center for Geographic Information — The stream geomorphic assessment is a physical assessment competed by geomorphologists to determine the condition and sensitivity of a stream. The SGA locations...

Smart Location Mapping

Science.gov (United States)

The Smart Location Database, Access to Jobs and Workers via Transit, and National Walkability Index tools can help assess indicators related to the built environment, transit accessibility, and walkability.

46 CFR 193.50-10 - Location.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Location. 193.50-10 Section 193.50-10 Shipping COAST... Details § 193.50-10 Location. (a) Approved hand portable fire extinguishers and semiportable fire extinguishing systems shall be installed in accordance with Table 193.50-10(a). The location of the equipment...

46 CFR 95.50-10 - Location.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Location. 95.50-10 Section 95.50-10 Shipping COAST GUARD...-10 Location. (a) Approved hand portable fire extinguishers and semiportable fire extinguishing systems shall be installed in accordance with Table 95.50-10(a). The location of the equipment shall be to...

Timing and locations of reef fish spawning off the southeastern United States.

Directory of Open Access Journals (Sweden)

Nicholas A Farmer

Full Text Available Managed reef fish in the Atlantic Ocean of the southeastern United States (SEUS support a multi-billion dollar industry. There is a broad interest in locating and protecting spawning fish from harvest, to enhance productivity and reduce the potential for overfishing. We assessed spatiotemporal cues for spawning for six species from four reef fish families, using data on individual spawning condition collected by over three decades of regional fishery-independent reef fish surveys, combined with a series of predictors derived from bathymetric features. We quantified the size of spawning areas used by reef fish across many years and identified several multispecies spawning locations. We quantitatively identified cues for peak spawning and generated predictive maps for Gray Triggerfish (Balistes capriscus, White Grunt (Haemulon plumierii, Red Snapper (Lutjanus campechanus, Vermilion Snapper (Rhomboplites aurorubens, Black Sea Bass (Centropristis striata, and Scamp (Mycteroperca phenax. For example, Red Snapper peak spawning was predicted in 24.7-29.0°C water prior to the new moon at locations with high curvature in the 24-30 m depth range off northeast Florida during June and July. External validation using scientific and fishery-dependent data collections strongly supported the predictive utility of our models. We identified locations where reconfiguration or expansion of existing marine protected areas would protect spawning reef fish. We recommend increased sampling off southern Florida (south of 27° N, during winter months, and in high-relief, high current habitats to improve our understanding of timing and location of reef fish spawning off the southeastern United States.

Inferring Groups of Objects, Preferred Routes, and Facility Locations from Trajectories

DEFF Research Database (Denmark)

Ceikute, Vaida

(i) infer groups of objects traveling together, (ii) determine routes preferred by local drivers, and (iii) identify attractive facility locations. First, we present framework that efficiently supports online discovery of groups of moving objects that travel together. We adopt a sampling......-independent approach that makes no assumptions about when object positions are sampled and that supports the use of approximate trajectories. The framework’s algorithms exploit density-based clustering to identify groups. Such identified groups are scored based on cardinality and duration. With the use of domination...... and similarity notions, groups of low interest are pruned, and a variety of different, interesting groups are returned. Results from empirical studies with real and synthetic data offer insight into the effectiveness and efficiency of the proposed framework. Next, we view GPS trajectories as trips that represent...

Selecting optimum locations for co-located wave and wind energy farms. Part I: The Co-Location Feasibility index

International Nuclear Information System (INIS)

Astariz, S.; Iglesias, G.

2016-01-01

Highlights: • New approach to identifying suitable sites for co-located wave and wind farms. • A new tool, the Co-Location Feasibility (CLF) index, is defined. • Its application is analysed by means of a case study off the Danish coast. • Hindcast and measured wave and wind data from 2005 to 2015 are used. • Third-generation models of winds and waves (WAsP and SWAN) are used. - Abstract: Marine energy is poised to play a fundamental role in meeting renewable energy and carbon emission targets thanks to the abundant, and still largely untapped, wave and tidal resources. However, it is often considered difficult and uneconomical – as is usually the case of nascent technologies. Combining various renewables, such as wave and offshore wind energy, has emerged as a solution to improve their competitiveness and in the process overcome other challenges that hinder their development. The objective of this paper is to develop a new approach to identifying suitable sites for co-located wave and wind farms based on the assessment of the available resources and technical constraints, and to illustrate its application by means of a case study off the Danish coast – an area of interest for combining wave and wind energy. The method is based on an ad hoc tool, the Co-Location Feasibility (CLF) index, and is based on a joint characterisation of the wave and wind resources, which takes into account not only the available power but also the correlation between both resources and the power variability. The analysis is carried out based on hindcast data and observations from 2005 to 2015, and using third-generation models of winds and waves – WAsP and SWAN, respectively. Upon selection and ranking, it is found that a number of sites in the study region are indeed suited to realising the synergies between wave and offshore wind energy. The approach developed in this work can be applied elsewhere.

Validation of the abbreviated Radon Progeny Integrating Sampling Unit (RPISU) method for Mesa County, Colorado

International Nuclear Information System (INIS)

Langner, G.H. Jr.

1987-06-01

The US Department of Energy (DOE) Office of Remedial Action and Waste Technology established the Technical Measurements Center at the DOE Grand Junction, Colorado, Projects Office to standardize, calibrate, and compare measurements made in support of DOE remedial action programs. Indoor radon-daughter concentration measurements are made to determine whether a structure is in need of remedial action. The Technical Measurements Center conducted this study to validate an abbreviated Radon Progeny Integrated Sampling Unit (RPISU) method of making indoor radon-daughter measurements to determine whether a structure has a radon-daughter concentration (RDC) below the levels specified in various program standards. The Technical Measurements Center established a criterion against which RDC measurements made using the RPISU sampling method are evaluated to determine if sampling can be terminated or whether further measurements are required. This abbreviated RPISU criterion was tested against 317 actual sets of RPISU data from measurements made over an eight-year period in Mesa County, Colorado. The data from each location were tested against a standard that was assumed to be the same as the actual annual average RDC from that location. At only two locations was the criterion found to fail. Using the abbreviated RPISU method, only 0.6% of locations sampled can be expected to be falsely indicated as having annual average RDC levels below a given standard

Gasbuggy, New Mexico, Hydrologic and Natural Gas Sampling and Analysis Results for 2009

International Nuclear Information System (INIS)

2009-11-01

The U.S. Department of Energy (DOE) Office of Legacy Management conducted hydrologic and natural gas sampling for the Gasbuggy, New Mexico, site on June 16, and 17, 2009. Hydrologic sampling consists of collecting water samples from water wells and surface water locations. Natural gas sampling consists of collecting both gas samples and samples of produced water from gas production wells. The water well samples were analyzed for gamma-emitting radionuclides and tritium. Surface water samples were analyzed for tritium. Water samples from gas production wells were analyzed for gamma-emitting radionuclides, gross alpha, gross beta, and tritium. Natural gas samples were analyzed for tritium and carbon-14. Water samples were analyzed by ALS Laboratory Group in Fort Collins, Colorado, and natural gas samples were analyzed by Isotech Laboratories in Champaign, Illinois. Concentrations of tritium and gamma-emitting radionuclides in water samples collected in the vicinity of the Gasbuggy site continue to demonstrate that the sample locations have not been impacted by detonation-related contaminants. Results from the sampling of natural gas from producing wells demonstrate that the gas wells nearest the Gasbuggy site are not currently impacted by detonation-related contaminants. Annual sampling of the gas production wells nearest the Gasbuggy site for gas and produced water will continue for the foreseeable future. The sampling frequency of water wells and surface water sources in the surrounding area will be reduced to once every 5 years. The next hydrologic sampling event at water wells, springs, and ponds will be in 2014.

Tissue Sampling Guides for Porcine Biomedical Models.

Science.gov (United States)

Albl, Barbara; Haesner, Serena; Braun-Reichhart, Christina; Streckel, Elisabeth; Renner, Simone; Seeliger, Frank; Wolf, Eckhard; Wanke, Rüdiger; Blutke, Andreas

2016-04-01

This article provides guidelines for organ and tissue sampling adapted to porcine animal models in translational medical research. Detailed protocols for the determination of sampling locations and numbers as well as recommendations on the orientation, size, and trimming direction of samples from ∼50 different porcine organs and tissues are provided in the Supplementary Material. The proposed sampling protocols include the generation of samples suitable for subsequent qualitative and quantitative analyses, including cryohistology, paraffin, and plastic histology; immunohistochemistry;in situhybridization; electron microscopy; and quantitative stereology as well as molecular analyses of DNA, RNA, proteins, metabolites, and electrolytes. With regard to the planned extent of sampling efforts, time, and personnel expenses, and dependent upon the scheduled analyses, different protocols are provided. These protocols are adjusted for (I) routine screenings, as used in general toxicity studies or in analyses of gene expression patterns or histopathological organ alterations, (II) advanced analyses of single organs/tissues, and (III) large-scale sampling procedures to be applied in biobank projects. Providing a robust reference for studies of porcine models, the described protocols will ensure the efficiency of sampling, the systematic recovery of high-quality samples representing the entire organ or tissue as well as the intra-/interstudy comparability and reproducibility of results. © The Author(s) 2016.

49 CFR 195.260 - Valves: Location.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Valves: Location. 195.260 Section 195.260... PIPELINE Construction § 195.260 Valves: Location. A valve must be installed at each of the following locations: (a) On the suction end and the discharge end of a pump station in a manner that permits isolation...

5 CFR 960.103 - Location.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Location. 960.103 Section 960.103 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT (CONTINUED) CIVIL SERVICE REGULATIONS (CONTINUED) FEDERAL EXECUTIVE BOARDS § 960.103 Location. Federal Executive Boards have been established and shall continue in...

Evolutionary economics and industry location

NARCIS (Netherlands)

Boschma, R.A.; Frenken, K.

2003-01-01

This paper aims to provide the outlines of an evolutionary economic geography of industry location. We discuss two evolutionary explanations of industry location, that is, one that concentrates on spin-offs, and one that focuses attention on knowledge and agglomeration economies. We claim that both

Soil-Transmitted Helminth Eggs Are Present in Soil at Multiple Locations within Households in Rural Kenya.

Directory of Open Access Journals (Sweden)

Lauren Steinbaum

Full Text Available Almost one-quarter of the world's population is infected with soil-transmitted helminths (STH. We conducted a study to determine the prevalence and location of STH-Ascaris, Trichuris, and hookworm spp.-egg contamination in soil within rural household plots in Kenya. Field staff collected soil samples from July to September 2014 from the house entrance and the latrine entrance of households in Kakamega County; additional spatial sampling was conducted at a subset of households (N = 22 samples from 3 households. We analyzed soil samples using a modified version of the US Environmental Protection Agency (EPA method for enumerating Ascaris in biosolids. We found 26.8% of households had one or more species of STH eggs present in the soil in at least one household location (n = 18 out of 67 households, and Ascaris was the most commonly detected STH (19.4%, n = 13 out of 67 households. Prevalence of STH eggs in soil was equally likely at the house entrance (19.4%, N = 67 as at the latrine entrance (11.3%, N = 62 (p = 0.41. We also detected STH eggs at bathing and food preparation areas in the three houses revisited for additional spatial sampling, indicating STH exposure can occur at multiple sites within a household plot, not just near the latrine. The highest concentration of eggs in one house occurred in the child's play area. Our findings suggest interventions to limit child exposure to household soil could complement other STH control strategies.

Simon and Garner effects with color and location: Evidence for two independent routes by which irrelevant location influences performance.

Science.gov (United States)

Fitousi, Daniel

2016-11-01

Classic theories of attention assume that the processing of a target's featural dimension (e.g., color) is contingent on the processing of its spatial location. The present study challenges this maxim. Three experiments evaluated the dimensional independence of spatial location and color using a combined Simon (Simon & Rudell Journal of Applied Psychology: 51, 300-304, 1967) and Garner (Garner, 1974) design. The results showed that when the stimulus's spatial location was rendered more discriminable than its color (Experiment 1 and 2), both Simon and Garner effects were obtained, and location interfered with color judgments to a larger extent than color intruded on location. However, when baseline discriminabilities of location and color were matched (Experiment 3), no Garner interference was obtained from location to color, yet Simon effects still emerged, proving resilient to manipulations of discriminability. Further correlational and distributional analyses showed that Garner and Simon effects have dissociable effects. A triple-route model is proposed to account for the results, according to which irrelevant location can influence performance via two independent location routes/codes.

Assessing genetic polymorphisms using DNA extracted from cells present in saliva samples

Directory of Open Access Journals (Sweden)

Nemoda Zsofia

2011-12-01

Full Text Available Abstract Background Technical advances following the Human Genome Project revealed that high-quality and -quantity DNA may be obtained from whole saliva samples. However, usability of previously collected samples and the effects of environmental conditions on the samples during collection have not been assessed in detail. In five studies we document the effects of sample volume, handling and storage conditions, type of collection device, and oral sampling location, on quantity, quality, and genetic assessment of DNA extracted from cells present in saliva. Methods Saliva samples were collected from ten adults in each study. Saliva volumes from .10-1.0 ml, different saliva collection devices, sampling locations in the mouth, room temperature storage, and multiple freeze-thaw cycles were tested. One representative single nucleotide polymorphism (SNP in the catechol-0-methyltransferase gene (COMT rs4680 and one representative variable number of tandem repeats (VNTR in the serotonin transporter gene (5-HTTLPR: serotonin transporter linked polymorphic region were selected for genetic analyses. Results The smallest tested whole saliva volume of .10 ml yielded, on average, 1.43 ± .77 μg DNA and gave accurate genotype calls in both genetic analyses. The usage of collection devices reduced the amount of DNA extracted from the saliva filtrates compared to the whole saliva sample, as 54-92% of the DNA was retained on the device. An "adhered cell" extraction enabled recovery of this DNA and provided good quality and quantity DNA. The DNA from both the saliva filtrates and the adhered cell recovery provided accurate genotype calls. The effects of storage at room temperature (up to 5 days, repeated freeze-thaw cycles (up to 6 cycles, and oral sampling location on DNA extraction and on genetic analysis from saliva were negligible. Conclusions Whole saliva samples with volumes of at least .10 ml were sufficient to extract good quality and quantity DNA. Using

Passive Acoustic Source Localization at a Low Sampling Rate Based on a Five-Element Cross Microphone Array

Directory of Open Access Journals (Sweden)

Yue Kan

2015-06-01

Full Text Available Accurate acoustic source localization at a low sampling rate (less than 10 kHz is still a challenging problem for small portable systems, especially for a multitasking micro-embedded system. A modification of the generalized cross-correlation (GCC method with the up-sampling (US theory is proposed and defined as the US-GCC method, which can improve the accuracy of the time delay of arrival (TDOA and source location at a low sampling rate. In this work, through the US operation, an input signal with a certain sampling rate can be converted into another signal with a higher frequency. Furthermore, the optimal interpolation factor for the US operation is derived according to localization computation time and the standard deviation (SD of target location estimations. On the one hand, simulation results show that absolute errors of the source locations based on the US-GCC method with an interpolation factor of 15 are approximately from 1/15- to 1/12-times those based on the GCC method, when the initial same sampling rates of both methods are 8 kHz. On the other hand, a simple and small portable passive acoustic source localization platform composed of a five-element cross microphone array has been designed and set up in this paper. The experiments on the established platform, which accurately locates a three-dimensional (3D near-field target at a low sampling rate demonstrate that the proposed method is workable.

USAID Activity Locations

Data.gov (United States)

US Agency for International Development — The USAID Activities dataset is a snapshot of activities supported by USAID including their geographical locations within countries at the time of the snapshot. The...

Uranium Location Database

Data.gov (United States)

U.S. Environmental Protection Agency — A GIS compiled locational database in Microsoft Access of ~15,000 mines with uranium occurrence or production, primarily in the western United States. The metadata...

Locating People Diagnosed With HIV for Public Health Action: Utility of HIV Case Surveillance and Other Data Sources.

Science.gov (United States)

Padilla, Mabel; Mattson, Christine L; Scheer, Susan; Udeagu, Chi-Chi N; Buskin, Susan E; Hughes, Alison J; Jaenicke, Thomas; Wohl, Amy Rock; Prejean, Joseph; Wei, Stanley C

Human immunodeficiency virus (HIV) case surveillance and other health care databases are increasingly being used for public health action, which has the potential to optimize the health outcomes of people living with HIV (PLWH). However, often PLWH cannot be located based on the contact information available in these data sources. We assessed the accuracy of contact information for PLWH in HIV case surveillance and additional data sources and whether time since diagnosis was associated with accurate contact information in HIV case surveillance and successful contact. The Case Surveillance-Based Sampling (CSBS) project was a pilot HIV surveillance system that selected a random population-based sample of people diagnosed with HIV from HIV case surveillance registries in 5 state and metropolitan areas. From November 2012 through June 2014, CSBS staff members attempted to locate and interview 1800 sampled people and used 22 data sources to search for contact information. Among 1063 contacted PLWH, HIV case surveillance data provided accurate telephone number, address, or HIV care facility information for 239 (22%), 412 (39%), and 827 (78%) sampled people, respectively. CSBS staff members used additional data sources, such as support services and commercial people-search databases, to locate and contact PLWH with insufficient contact information in HIV case surveillance. PLWH diagnosed surveillance than were PLWH diagnosed ≥1 year ago ( P = .002), and the benefit from using additional data sources was greater for PLWH with more longstanding HIV infection ( P surveillance cannot provide accurate contact information, health departments can prioritize searching additional data sources, especially for people with more longstanding HIV infection.

Adult health study reference papers. Selection of the sample. Characteristics of the sample

Energy Technology Data Exchange (ETDEWEB)

Beebe, G W; Fujisawa, Hideo; Yamasaki, Mitsuru

1960-12-14

The characteristics and selection of the clinical sample have been described in some detail to provide information on the comparability of the exposure groups with respect to factors excluded from the matching criteria and to provide basic descriptive information potentially relevant to individual studies that may be done within the framework of the Adult Health Study. The characteristics under review here are age, sex, many different aspects of residence, marital status, occupation and industry, details of location and shielding ATB, acute radiation signs and symptoms, and prior ABCC medical or pathology examinations. 5 references, 57 tables.

Teaching Health Center Graduate Medical Education Locations Predominantly Located in Federally Designated Underserved Areas.

Science.gov (United States)

Barclift, Songhai C; Brown, Elizabeth J; Finnegan, Sean C; Cohen, Elena R; Klink, Kathleen

2016-05-01

Background The Teaching Health Center Graduate Medical Education (THCGME) program is an Affordable Care Act funding initiative designed to expand primary care residency training in community-based ambulatory settings. Statute suggests, but does not require, training in underserved settings. Residents who train in underserved settings are more likely to go on to practice in similar settings, and graduates more often than not practice near where they have trained. Objective The objective of this study was to describe and quantify federally designated clinical continuity training sites of the THCGME program. Methods Geographic locations of the training sites were collected and characterized as Health Professional Shortage Area, Medically Underserved Area, Population, or rural areas, and were compared with the distribution of Centers for Medicare and Medicaid Services (CMS)-funded training positions. Results More than half of the teaching health centers (57%) are located in states that are in the 4 quintiles with the lowest CMS-funded resident-to-population ratio. Of the 109 training sites identified, more than 70% are located in federally designated high-need areas. Conclusions The THCGME program is a model that funds residency training in community-based ambulatory settings. Statute suggests, but does not explicitly require, that training take place in underserved settings. Because the majority of the 109 clinical training sites of the 60 funded programs in 2014-2015 are located in federally designated underserved locations, the THCGME program deserves further study as a model to improve primary care distribution into high-need communities.

P2-13: Location word Cues' Effect on Location Discrimination Task: Cross-Modal Study

Directory of Open Access Journals (Sweden)

Satoko Ohtsuka

2012-10-01

Full Text Available As is well known, participants are slower and make more errors in responding to the display color of an incongruent color word than a congruent one. This traditional stroop effect is often accounted for with relatively automatic and dominant word processing. Although the word dominance account has been widely supported, it is not clear in what extent of perceptual tasks it is valid. Here we aimed to examine whether the word dominance effect is observed in location stroop tasks and in audio-visual situations. The participants were required to press a key according to the location of visual (Experiment 1 and audio (Experiment 2 targets, left or right, as soon as possible. A cue of written (Experiments 1a and 2a or spoken (Experiments 1b and 2b location words, “left” or “right”, was presented on the left or right side of the fixation with cue lead times (CLT of 200 ms and 1200 ms. Reaction time from target presentation to key press was recorded as a dependent variable. The results were that the location validity effect was marked in within-modality but less so in cross-modality trials. The word validity effect was strong in within- but not in cross-modality trials. The CLT gave some effect of inhibition of return. So the word dominance could be less effective in location tasks and in cross-modal situations. The spatial correspondence seems to overcome the word effect.

Improvements in and relating to the incubation of samples

International Nuclear Information System (INIS)

Bagshawe, K.D.

1978-01-01

Apparatus is described for incubating a plurality of biological samples and particularly as part of an analysis, e.g. radioimmunoassay or enzyme assay, of the samples. The apparatus is comprised of an incubation station with a plurality of containers to which samples together with diluent and reagents are supplied. The containers are arranged in rows in two side-by-side columns and are circulated sequentially. Sample removal means is provided either at a fixed location or at a movable point relative to the incubator. Circulation of the containers and the length of sample incubation time is controlled by a computer. The incubation station may include a plurality of sections with the columns in communication so that rows of samples can be moved from the column of one section to the column of an adjacent section, to provide alternative paths for circulation of the samples. (author)

Evaluation of reproductive endocrine status in hornyhead turbot sampled from Southern California's urbanized coastal environments.

Science.gov (United States)

Reyes, Jesus A; Vidal-Dorsch, Doris E; Schlenk, Daniel; Bay, Steven M; Armstrong, Jeffrey L; Gully, Joseph R; Cash, Curtis; Baker, Michael; Stebbins, Timothy D; Hardiman, Gary; Kelley, Kevin M

2012-12-01

As part of a regionwide collaboration to determine the occurrence of contaminants and biological effects in coastal ecosystems offshore of urban southern California, the present study characterized the reproductive endocrinology of an indigenous flatfish, the hornyhead turbot (Pleuronichthys verticalis), and compared groups sampled from different study sites representing varying degrees of pollution to screen for potential endocrine disruptive effects. Turbot were sampled from locations near the coastal discharge sites of four large municipal wastewater treatment plants (WWTPs) located between Los Angeles and San Diego, California, USA, and were compared with fish sampled from three far-field reference locations in the region. Despite environmental presence of both legacy contaminants and contaminants of emerging concern and evidence for fish exposure to several classes of contaminants, both males and females generally exhibited coordinated seasonal reproductive cycles at all study sites. Patterns observed included peaks in sex steroids (17β-estradiol, testosterone, 11-ketotestosterone) in the spring and low levels in the fall, changes corresponding to similarly timed gonadal changes and plasma vitellogenin concentrations in females. Comparisons between fish captured at the different study sites demonstrated some regional differences in plasma levels of estrogens and androgens, indicative of location-associated effects on the endocrine system. The observed differences, however, could not be linked to the ocean discharge locations of four of the largest WWTPs in the world. Copyright © 2012 SETAC.

Investigation on location-dependent detectability of a small mass for digital breast tomosynthesis evaluation

Science.gov (United States)

Lee, Changwoo; Baek, Jongduk; Park, Subok

2016-03-01

Digital breast tomosynthesis (DBT) is an emerging imaging modality for improved breast cancer detection and diagnosis [1-5]. Numerous efforts have been made to find quantitative metrics associated with mammographic image quality assessment, such as the exponent β of anatomical noise power spectrum, glandularity, contrast noise ratio, etc. [6-8]. In addition, with the use of Fourier-domain detectability for a task-based assessment of DBT, a stationarity assumption on reconstructed image statistics was often made [9-11], resulting in the use of multiple regions-of-interest (ROIs) from different locations in order to increase sample size. While all these metrics provide some information on mammographic image characteristics and signal detection, the relationship between these metrics and detectability in DBT evaluation has not been fully understood. In this work, we investigated spatial-domain detectability trends and levels as a function of the number of slices Ns at three different ROI locations on the same image slice, where background statistics differ in terms of the aforementioned metrics. Detectabilities for the three ROI locations were calculated using multi-slice channelized Hotelling observers with 2D/3D Laguerre-Gauss channels. Our simulation results show that detectability levels and trends as a function of Ns vary across these three ROI locations. They also show that the exponent β, mean glandularity, and mean attenuation coefficient vary across the three ROI locations but they do not necessarily predict the ranking of detectability levels and trends across these ROI locations.