Distribution of chemical elements in soils and stream sediments in the area of abandoned Sb–As–Tl Allchar mine, Republic of Macedonia

Energy Technology Data Exchange (ETDEWEB)

Bačeva, Katerina [Institute of Chemistry, Faculty of Natural Sciences and Mathematics, Ss. Cyril and Methodius University, POB 162, 1000 Skopje (Macedonia, The Former Yugoslav Republic of); Stafilov, Trajče, E-mail: trajcest@pmf.ukim.mk [Institute of Chemistry, Faculty of Natural Sciences and Mathematics, Ss. Cyril and Methodius University, POB 162, 1000 Skopje (Macedonia, The Former Yugoslav Republic of); Šajn, Robert [Geological Survey of Slovenia, Ljubljana (Slovenia); Tănăselia, Claudiu [INCDO-INOE 2000 Research Institute for Analytical Instrumentation (ICIA), Cluj-Napoca (Romania); Makreski, Petre [Institute of Chemistry, Faculty of Natural Sciences and Mathematics, Ss. Cyril and Methodius University, POB 162, 1000 Skopje (Macedonia, The Former Yugoslav Republic of)

2014-08-15

The aim of this study was to investigate the distribution of some toxic elements in topsoil and subsoil, focusing on the identification of natural and anthropogenic element sources in the small region of rare As–Sb–Tl mineralization outcrop and abandoned mine Allchar known for the highest natural concentration of Tl in soil worldwide. The samples of soil and sediments after total digestion were analyzed by inductively coupled plasma–mass spectrometry (ICP–MS) and inductively coupled plasma–atomic emission spectrometry (ICP–AES). Factor analysis (FA) was used to identify and characterize element associations. Six associations of elements were determined by the method of multivariate statistics: Rb–Ta–K–Nb–Ga–Sn–Ba–Bi–Li–Be–(La–Eu)–Hf–Zr–Zn–In–Pd–Ag–Pt–Mg; Tl–As–Sb–Hg; Te–S–Ag–Pt–Al–Sc–(Gd–Lu)–Y; Fe–Cu–V–Ge–Co–In; Pd–Zr–Hf–W–Be and Ni–Mn–Co–Cr–Mg. The purpose of the assessment was to determine the nature and extent of potential contamination as well as to broadly assess possible impacts to human health and the environment. The results from the analysis of the collected samples in the vicinity of the mine revealed that As and Tl elements have the highest median values. Higher median values for Sb are obviously as a result of the past mining activities and as a result of area surface phenomena in the past. - Highlights: • Soil and river sediments were analyzed from Sb–As–Tl Allchar locality. • An increased content of certain toxic elements for environment was determined. • Highest As and Tl contents are obtained in the close vicinity of Allchar mine. • River sediments portray 160 times higher content of Sb than EU values. • The results classify Allchar as probably the highest natural Tl-deposit worldwide.

Solid solutions of thallium in TlGaSe2, TlGaS2, and TlInS2

International Nuclear Information System (INIS)

Voroshilov, Yu. V.; Potorii, M.V.; Shevchenko, S.V.

1986-01-01

The authors study the nature of the dissolution of thallium in ternary phases. They have synthesized alloys of the stoichiometric compositions TlGaS 2 , TlGaSe 2 , and T1InS 2 , and their solid solutions, maximally enriched in thallium, the compositions of which were Tl /SUB 1.34/ GA /SUB 0.89/ S 2 , Tl /SUB 1.31/ Ga /SUB 0.90/ Se 2 , and Tl /SUB 1.15/ In /SUB 0.95/ S /SUB 2./ . Samples were synthesized from the elemental components of the following purities: gallium of V4 grade; indium of V4 grade; thallium of T1000 grade; selenium of special purity 22-4 grade, and sulfur of special purity garde. The compositions were checked by x-ray-phase-(DRON-0.5) and microstructural-analyses with simultaneous determination of the density and microhardness of the samples. It is found that the lattic parameter increases and the increase in the density and microhardness points to strengthening of the structure during the formation of the solid solutions

The TAC of porcelain samples and its influence on TL dating

International Nuclear Information System (INIS)

Leung, P.L.; Stokes, M.J.; Xia Junding; Wang Weida

1997-01-01

The thermal activation characteristics of porcelain slice samples for pre-dose dating were obtained by using the multiple activation method. The influence of activation temperature on TL dating was also studied. The results show that choosing a temperature corresponding to the maximum sensitivity on the TAC curve as the activation temperature is very important in the multiple activation method

Spectral measurements of loess TL

International Nuclear Information System (INIS)

Rendell, H.M.; Mann, S.J.; Townsend, P.D.

1988-01-01

Variations in thermoluminescence (TL) glow curves are reported for two loess samples when examined with broad band filters in the range 275-650 nm. Samples show striking differences in bleaching behaviour, when their TL emissions are observed in the u.v., blue, green and yellow spectral regions. The age estimates, given by the equivalent dose (ED) values, differ by up to a factor of two for analyses using the green and u.v. TL signals. These ED values also vary with prolonged room temperature storage between the bleaching and irradiation steps. The anomalies in the bleaching behaviour are interpreted in terms of changes in TL efficiency. The results have major implications for the regeneration method of TL dating for these fine-grained sediments and suggest that reliable dates obtained by it may be fortuitous. (author)

First principles study of (Cd, Hg, In, Tl, Sn, Pb, As, Sb, Bi, Se) modified Pt(111), Pt(100) and Pt(211) electrodes as CO oxidation catalysts

DEFF Research Database (Denmark)

Tripkovic, Vladimir

2015-01-01

. The coverage dependence as a function of potential for ten different adatom species (Cd, Hg, In, Tl, Sn, Pb, As, Sb, Bi, Se) on bare and CO saturated Pt(111), Pt(100) and Pt(211) surfaces has been established by means of Density Functional Theory calculations. Most of the adatoms are very stable under standard......, given by the OH formation potentials from water, is dependent on the oxophilicity of the adatoms, and is found to scale almost inversely with the adatom stability. In electrolyte solutions saturated with CO, the stability reduces to roughly half of that on bare Pt surfaces. Irrespective of the CO...

Correlation of basic TL, OSL and IRSL properties of ten K-feldspar samples of various origins

Energy Technology Data Exchange (ETDEWEB)

Sfampa, I.K. [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124 Thessaloniki (Greece); Polymeris, G.S. [Institute of Nuclear Sciences, Ankara University, 06100 Besevler, Ankara (Turkey); Pagonis, V. [McDaniel College, Physics Department, Westminster, MD 21157 (United States); Theodosoglou, E. [Department of Mineralogy-Petrology-Economic Geology, School of Geology, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Tsirliganis, N.C. [Laboratory of Radiation Applications and Archaeological Dating, Department of Archaeometry and Physicochemical Measurements, ‘Athena’ R.& I.C., Kimmeria University Campus, GR67100 Xanthi (Greece); Kitis, G., E-mail: gkitis@auth.gr [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124 Thessaloniki (Greece)

2015-09-15

Highlights: • OSL and IRSL bleaching behavior of ten K-feldspar samples is presented. • OSL and IRSL decay curves were component resolved using tunneling model. • The growth of integrated OSL and IRSL signals versus time was described by new expression based on tunneling model. • Correlation between TL, OSL and IRSL signals and of all properties with K-feldspar structure was discussed. - Abstract: Feldspars stand among the most widely used minerals in dosimetric methods of dating using thermoluminescence (TL), optically stimulated luminescence (OSL) and infrared stimulated luminescence (IRSL). Having very good dosimetric properties, they can in principle contribute to the dating of every site of archaeological and geological interest. The present work studies basic properties of ten naturally occurring K-feldspar samples belonging to three feldspar species, namely sanidine, orthoclase and microcline. The basic properties studied are (a) the influence of blue light and infrared stimulation on the thermoluminescence glow-curves, (b) the growth of OSL, IRSL, residual TL and TL-loss as a function of OSL and IRSL bleaching time and (c) the correlation between the OSL and IRSL signals and the energy levels responsible for the TL glow-curve. All experimental data were fitted using analytical expressions derived from a recently developed tunneling recombination model. The results show that the analytical expressions provide excellent fits to all experimental results, thus verifying the tunneling recombination mechanism in these materials and providing valuable information about the concentrations of luminescence centers.

High-Tc superconductivity of Tl-Ba-Ca-Cu-O samples

International Nuclear Information System (INIS)

Porjesz, T.; Kirschner, I.; Kovacs, G.

1988-08-01

A TlBaCaCuO 4.5+x compound has been investigated from the point of view of superconductivity. Depending on the heat treatment, one part of the sample exhibits superconductivity with an onset of 121 K and zero resistivity of 106 K and the other part of them shows a sharp drop in resistivity at 130 K which hints at an existence of superconducting grains. This picture was confirmed by magnetic and ESR measurements giving possibility for estimation of critical magnetic fields. (author). 5 refs, 6 figs

Comparative Study of 11 Honey Samples Sold in Riyadh Saudi Arabia

OpenAIRE

Al Tufail, M. A. [محمد عبد الله الطفيل; Al Araidh, I. A. [ابراهيم عبد الله العريض

2006-01-01

11 honey various samples commercially available in Saudi Arabia, were subjected to chemical, toxicological and bacteriological tests. The samples were checked for As and CN, presence of pollens, and for bacteria contamination. The carbohydrate profile was analyzed with HPLC. Fe, P, Ca, K, and Mg were measured with colorimetry. Toxic metals, As, Pb, Sb, Tl, and Hg were determined with ICP-MS. The samples were investigated by GC-MS. The investigation revealed the presence of syringaldehyde, men...

207Pb and 205Tl NMR on Perovskite Type Crystals APbX3 (A = Cs, Tl, X = Br, I)

Science.gov (United States)

Sharma, Surendra; Weiden, Norbert; Weiss, Alarich

1987-11-01

By 205Tl and 207Pb NM R the chemical shift in polycrystalline samples of binary halides AX, BX2 and ternary halides ABX3 (A = Cs, Tl; B = Pb; X = Br, I) was studied at room temperature. The chemical shift tensors δ ( 205Tl) and δ (207Pb) were determined in magnitude and orientation on single crystals of the orthorhombic TlPbI3. The components of the δ(205Tl) tensor are δx (205Tl) || a = 611ppm; δy (205Tl) || b = 680 ppm; δZ(205Tl) || c = 1329 ppm; δiso(205Tl) = 873.3 ppm (with respect to 3.4 molar aqueous solution of TlOOCCH3). The chemical shift tensor of 207Pb in TlPbI3 shows two orientations. One of them is: δx (207Pb) = 3760 ppm, inclined 30° from b towards c, δy(207Pb) || a = 3485 ppm, δz(207Pb) = 2639 ppm inclined 120° from b towards c. δiso(207Pb) = 3295 ppm (with respect to saturated aqueous solution of Pb(NO3)2). The results are discussed with respect to the crystal structure and a model to explain orientation and anisotropy of the tensors δ(205Tl) and δ(207Pb) in TlPbI3 is proposed. In the system CsPbBr3-x Ix δ(207Pb) was studied on polycrystalline samples. The chemical shift increases with increasing x and negative excess shift is observed.

Sb-related defects in Sb-doped ZnO thin film grown by pulsed laser deposition

Science.gov (United States)

Luo, Caiqin; Ho, Lok-Ping; Azad, Fahad; Anwand, Wolfgang; Butterling, Maik; Wagner, Andreas; Kuznetsov, Andrej; Zhu, Hai; Su, Shichen; Ling, Francis Chi-Chung

2018-04-01

Sb-doped ZnO films were fabricated on c-plane sapphire using the pulsed laser deposition method and characterized by Hall effect measurement, X-ray photoelectron spectroscopy, X-ray diffraction, photoluminescence, and positron annihilation spectroscopy. Systematic studies on the growth conditions with different Sb composition, oxygen pressure, and post-growth annealing were conducted. If the Sb doping concentration is lower than the threshold ˜8 × 1020 cm-3, the as-grown films grown with an appropriate oxygen pressure could be n˜4 × 1020 cm-3. The shallow donor was attributed to the SbZn related defect. Annealing these samples led to the formation of the SbZn-2VZn shallow acceptor which subsequently compensated for the free carrier. For samples with Sb concentration exceeding the threshold, the yielded as-grown samples were highly resistive. X-ray diffraction results showed that the Sb dopant occupied the O site rather than the Zn site as the Sb doping exceeded the threshold, whereas the SbO related deep acceptor was responsible for the high resistivity of the samples.

Automation of TL brick dating by ADAM-1

International Nuclear Information System (INIS)

Cechak, T.; Gerndt, J.; Hirsl, P.; Jirousek, P.; Kubelik, M.; Musilek, L.; Kanaval, J.

2000-01-01

Thermoluminescence has become an established dating method for ceramics and more recently for bricks. Based on the experiences of the work carried out since the late 1970's at the Rathgen-Forschungslabor in Berlin on the dating of bricks from historic architecture, and after evaluating all commercially available and some individually built automated and semi-automated TL-readers, a specially adapted machine for the fine grain dating of bricks was constructed in an interdisciplinary research project, undertaken by a team recruited from three faculties of the Czech Technical University in Prague. The result is the automated TL-reader ADAM-1 (Automated Dating Apparatus for Monuments) for the dating of historic architecture. Both the specific adaptation of the technique and the necessary optimal automation have influenced the design of this TL-reader. The principle advantage of brick as opposed to ceramic TL-dating emerges from the possibility of being able to obtain both a large number of samples and an above average quantity of datable material from each sample. This, together with the specific physical and chemical conditions in a brick wall, allowed a rethinking of the traditional error calculation and thus lower error margins as those obtained when dating ceramic shards. The TL-reader must therefore be able to measure and evaluate automatically numerous samples. The annular sample holder of ADAM-1 has 60 sample positions, which allow the irradiation and evaluation of samples taken from two locations. The thirty samples from one sampling point are divided into subgroups, which are processed in various ways. Three samples serve for a rough estimate of the TL sensitivity of the brick material. Nine samples are used for the measurement of 'natural TL' of the material. A further nine samples are used for testing the sensitivity of the material to beta radiation. The last nine samples serve for the testing of the sensitivity to alpha radiation. To determine the

InSb semiconductors and (In,Mn)Sb diluted magnetic semiconductors. Growth and properties

Energy Technology Data Exchange (ETDEWEB)

Tran, Lien

2011-04-13

This dissertation describes investigations of the growth by molecular beam epitaxy and the characterization of the semiconductor InSb as well as the diluted magnetic semiconductor (DMS) In{sub 1-x}Mn{sub x}Sb. The InSb films were grown on GaAs (001) substrate and Si (001) offcut by 4 toward (110) substrate up to a thickness of about 2 {mu}m, in spite of a large lattice mismatch between the epi-layer and substrate (14.6% between InSb and GaAs, and 19.3% between InSb and Si). After optimizing the growth conditions, the best InSb films grown directly on GaAs without any special technique results in a high crystal quality, low noise, and an electron mobility of 41100 cm{sup 2}/V s Vs with associated electron concentration of 2.9.10{sup 6} cm{sup -3} at 300 K. Such structures could be used, for example, for infrared detector structures. The growth of InSb on Si, however, is a challenge. In order to successfully grow InSb on Si, tilted substrates and the insertion of buffer layers were used, which helps to reduce the lattice mismatch as well as the formation of defects, and hence to improve the crystal quality. An electron mobility of 24000 cm{sup 2}/V s measured at 300 K, with an associated carrier concentration of 2.6.10{sup 1}6 cm{sup -3} is found for the best sample that was grown at 340 C with a 0.06 {mu}m-thick GaSb/AlSb superlattice buffer layer. The smaller value of electron mobility (compared to the best GaAsbased sample) is related to a higher density of microtwins and stacking faults as well as threading dislocations in the near-interface region as shown by transmission electron microscopy. Deep level noise spectra indicate the existence of deep levels in both GaAs and Si-based samples. The samples grown on Si exhibit the lowest Hooge factor at 300 K, lower than the samples grown on GaAs. Taking the optimized growth conditions of InSb/GaAs, the diluted magnetic semiconductor In{sub 1-x}Mn{sub x}Sb/GaAs (001) is prepared by adding a few percent of Mn into the

InSb semiconductors and (In,Mn)Sb diluted magnetic semiconductors: Growth and properties

International Nuclear Information System (INIS)

Tran, Lien

2011-01-01

This dissertation describes investigations of the growth by molecular beam epitaxy and the characterization of the semiconductor InSb as well as the diluted magnetic semiconductor (DMS) In 1-x Mn x Sb. The InSb films were grown on GaAs (001) substrate and Si (001) offcut by 4 toward (110) substrate up to a thickness of about 2 μm, in spite of a large lattice mismatch between the epi-layer and substrate (14.6% between InSb and GaAs, and 19.3% between InSb and Si). After optimizing the growth conditions, the best InSb films grown directly on GaAs without any special technique results in a high crystal quality, low noise, and an electron mobility of 41100 cm 2 /V s Vs with associated electron concentration of 2.9.10 6 cm -3 at 300 K. Such structures could be used, for example, for infrared detector structures. The growth of InSb on Si, however, is a challenge. In order to successfully grow InSb on Si, tilted substrates and the insertion of buffer layers were used, which helps to reduce the lattice mismatch as well as the formation of defects, and hence to improve the crystal quality. An electron mobility of 24000 cm 2 /V s measured at 300 K, with an associated carrier concentration of 2.6.10 1 6 cm -3 is found for the best sample that was grown at 340 C with a 0.06 μm-thick GaSb/AlSb superlattice buffer layer. The smaller value of electron mobility (compared to the best GaAsbased sample) is related to a higher density of microtwins and stacking faults as well as threading dislocations in the near-interface region as shown by transmission electron microscopy. Deep level noise spectra indicate the existence of deep levels in both GaAs and Si-based samples. The samples grown on Si exhibit the lowest Hooge factor at 300 K, lower than the samples grown on GaAs. Taking the optimized growth conditions of InSb/GaAs, the diluted magnetic semiconductor In 1-x Mn x Sb/GaAs (001) is prepared by adding a few percent of Mn into the host material InSb during growth. I have

The neutron diffraction of molten TlCl, TlBr, and TlI

International Nuclear Information System (INIS)

Satow, T.; Uemura, O.; Hoshino, K.; Watanabe, T.

1984-01-01

Structure factors S(K) for liquid TlCl, TlBr, and TlI are determined by neutron diffraction measurements. Atomic radial distribution functions (RDF) derived from S(K) are presented. All RDF values are slightly smaller than those of their solid state counter parts. Results show that TlX has a tendency not to retain cesium-chloride type local order, but to take sodium-chloride type order when melting

ESR and TL age determination of caliche nodules

Energy Technology Data Exchange (ETDEWEB)

Oezer, A.M. (Middle East Technical Univ., Ankara (Turkey)); Wieser, A.; Goeksu, H.Y.; Mueller, P.; Regulla, D.F. (Gesellschaft fuer Strahlen- und Umweltforschung mbH Muenchen, Neuherberg (Germany, F.R.). Inst. fuer Strahlenschutz); Erol, O. (Istanbul Univ. (Turkey). School of Geography and Marine Sciences)

1989-01-01

Feasibility of dating caliche nodules by ESR and TL is investigated. For both methods the properties of the dating signal are described. Chemical composition as well as TL glow curves of caliches originating from different localities exhibit some differences. Due to the complexity of the TL glow curves, some samples required a special post-annealing procedure in order to resolve the main TL peak for age determination. Typical ESR calcite signals do not exist in caliche, therefore usefulness of the g=2.0040 ESR signal is studied. The results of TL and ESR ages are found to be compatible except for two samples. Possible causes of the discrepancy in these samples are discussed. It is shown that, with proper treatment of the radiation-induced signals, it was possible to date caliche formations older than 350 ka, which is not achievable with other methods like uranium series disequilibrium and/or radiocarbon dating. (author).

ESR and TL age determination of caliche nodules

International Nuclear Information System (INIS)

Oezer, A.M.; Wieser, A.; Goeksu, H.Y.; Mueller, P.; Regulla, D.F.; Erol, O.

1989-01-01

Feasibility of dating caliche nodules by ESR and TL is investigated. For both methods the properties of the dating signal are described. Chemical composition as well as TL glow curves of caliches originating from different localities exhibit some differences. Due to the complexity of the TL glow curves, some samples required a special post-annealing procedure in order to resolve the main TL peak for age determination. Typical ESR calcite signals do not exist in caliche, therefore usefulness of the g=2.0040 ESR signal is studied. The results of TL and ESR ages are found to be compatible except for two samples. Possible causes of the discrepancy in these samples are discussed. It is shown that, with proper treatment of the radiation-induced signals, it was possible to date caliche formations older than 350 ka, which is not achievable with other methods like uranium series disequilibrium and/or radiocarbon dating. (author)

Compositional and structural characterisation of GaSb and GaInSb

International Nuclear Information System (INIS)

Corregidor, V.; Alves, E.; Alves, L.C.; Barradas, N.P.; Duffar, Th.; Franco, N.; Marques, C.; Mitric, A.

2005-01-01

Low band gap III-V semiconductors are researched for applications in thermophotovoltaic technology. GaSb crystal is often used as a substrate. Ga 1-x In x Sb is also a promising substrate material, because its lattice parameters can be adjusted by controlling x. We used a new method to synthesise GaSb and GaInSb, in which a high frequency alternate magnetic field is used to heat, to melt and to mix the elements. We present a compositional and structural characterisation of the materials using a combination of complementary techniques. Rutherford backscattering was used to determine accurately the composition of the GaSb. With proton induced X-ray emission in conjunction with a 3 x 3 μm 2 micro-beam we studied the homogeneity of the samples. Structural analysis and phase identification were done with X-ray diffraction. The results for GaSb show a homogeneous composition while the GaInSb samples were found to be strongly heterogeneous at the end of the ingot. The ingots produced are competitive feed material, when compared to other growth techniques, to be used in a second step for the production of good quality ternary crystals

Doped Tl-1212 and Tl-1223 superconductors

International Nuclear Information System (INIS)

Eder, M.H.

2001-09-01

This work describes the preparation and characterization of thallium-lead-strontium-barium-calcium-(uranium)-copperoxide (Tl-1212, Tl-1223) high-temperature superconductors. The precursors were prepared via nitrate method. After calcination the oxidic powders were mixed with stoichiometric amounts of an Tl 2 O 3 , PbO, Er 2 O 3 and Gd 2 O 3 by milling and afterwards uniaxial compressed. Sintering was carried out in silver foils. X-ray diffractometry and high-resolution microscopy in combination with scanning electron microscopy (including EDAX) were used to study the influence of varying thallium/lead-, strontium/barium-, calcium/rare earth element ratios and the effect of uranium on the phase composition and microstructure of bulk superconductors. Furthermore the influence of the composition on the electrical and magnetical properties was studied. On phase pure Tl-1212 and Tl-1223 superconductors NMR-measurements were done. Small amounts of gadolinium and erbium instead of calcium and excess-uranium have a positive impact on the electrical and magnetical properties of the Tl-1223 superconductors. Higher amounts of these doping elements favor the Tl-1212 phase. Tl-1212 superconductors with varying thallium/lead- strontium/barium- and calcium/gadolinium ratios were prepared phasepure in wide range of doping. Transition temperatures up to 96 K were achieved. It was shown that lead has an oxidation number of +4 and thallium of +3. (author)

OSL, TL and IRSL emission spectra of sedimentary quartz and feldspar samples

International Nuclear Information System (INIS)

Lomax, Johanna; Mittelstraß, Dirk; Kreutzer, Sebastian; Fuchs, Markus

2015-01-01

This contribution presents a variety of different luminescence emission spectra from sedimentary feldspar and quartz samples under various stimulation modes. These are green stimulated quartz (OSL-) spectra, quartz TL spectra, feldspar IRSL and post-IR IRSL spectra. A focus was set at recording OSL and IRSL spectra at elevated stimulation temperatures such as routinely applied in luminescence dating. This was to test whether optical stimulation at elevated temperatures results in a shift of emission peaks. For OSL emissions of quartz, this has so far not been tested. In case of feldspar emissions, post-IR IRSL conditions, hence IRSL emissions at a low temperature, directly followed by high temperature post-IRSL emissions, are explicitly investigated. All spectra were recorded using a new system incorporated into a Lexsyg luminescence reader. Thus, this study, besides presenting new spectral data, also serves as a feasibility study for this new device. It is shown that (a) the new device is capable of automatically measuring different sorts of spectra, also at elevated temperatures, (b) known thermally and optically stimulated peak emissions of quartz and feldspar are confirmed, (c) obtained IRSL and OSL spectra indicate that there is no significant relation between peak emission and stimulation temperature. - Highlights: • We have measured OSL, IRSL and TL emission spectra of sedimentary quartz and feldspar samples. • Spectral analyses were performed at elevated stimulation temperatures. • Emission spectra show very little variation with stimulation temperatures.

SLUDGE BATCH 5 ACCEPTANCE EVALUATION RADIONUCLIDE CONCENTRATIONS IN TANK 51 SB5 QUALIFICATION SAMPLE PREPARED AT SRNL

International Nuclear Information System (INIS)

Bannochie, C; Ned Bibler, N; David Diprete, D

2008-01-01

Presented in this report are radionuclide concentrations required as part of the program of qualifying Sludge Batch Five (SB5) for processing in the Defense Waste Processing Facility (DWPF). Part of this SB5 material is currently in Tank 51 being washed and prepared for transfer to Tank 40. The acceptance evaluation needs to be completed prior to the transfer of the material in Tank 51 to Tank 40 to complete the formation of SB5. The sludge slurry in Tank 40 has already been qualified for DWPF and is currently being processed as SB4. The radionuclide concentrations were measured or estimated in the Tank 51 SB5 Qualification Sample prepared at Savannah River National Laboratory (SRNL). This sample was prepared from the three liter sample of Tank 51 sludge slurry taken on March 21, 2008. The sample was delivered to SRNL where it was initially characterized in the Shielded Cells. Under direction of the Liquid Waste Organization it was then modified by five washes, six decants, an addition of Pu/Be from Canyon Tank 16.4, and an addition of NaNO2. This final slurry now has a composition expected to be similar to that of the slurry in Tank 51 after final preparations have been made for transfer of that slurry to Ta Determining the radionuclide concentrations in this Tank 51 SB5 Qualification Sample is part of the work requested in Technical Task Request (TTR) No. HLW-DWPF-TTR-2008-0010. The work with this qualification sample is covered by a Task Technical and Quality Assurance Plan and an Analytical Study Plan. The radionuclides included in this report are needed for the DWPF Radiological Program Evaluation, the DWPF Waste Acceptance Criteria (TSR/WAC) Evaluation, and the DWPF Solid Waste Characterization Program (TTR Task 2). Radionuclides required to meet the Waste Acceptance Product Specifications (TTR Task 5) will be measured at a later date after the slurry from Tank 51 has been transferred to Tank 40. Then a sample of the as-processed SB5 will be taken and

Spectrophotometric determination of Tl carrier in 201Tl-TlCl injection

International Nuclear Information System (INIS)

Gong Quansheng; Jing Lie

1997-01-01

A simple and sensitive method for the spectrophotometric determination of carrier content (Thallium) in 201 Tl-TlCl injection is described. Thallium (I) is oxidised to Thallium (III) by aqueous bromine, then excess bromine is removed by adding sulfosalicylic acid. In buffer solution (NH 4 Cl-NH 4 OH) at pH 11.7 with the presence of emulsifier OP, thallium (III) and cadion form a complex having an absorption maximum at 469 nm with a molar absorptivity of 1.37 x 10 4 m 2 /mol. Beer's law is obeyed in the concentration range of 0-7 μg/5 mL. The effect of impurity elements in 201 Tl-TlCl injection is examined. It is an ideal method for the analysis of radioactive solution

Yield of 117Sb, 118mSb, 120mSb, 122Sb, 124Sb in reactions Sn (p, xn)

International Nuclear Information System (INIS)

Dmitriev, P.P.; Konstantinov, I.O.

1993-01-01

Yield of 117 Sb, 118m Sb, 120m Sb, 122 Sb, 124 Sb from thick target depending on proton energy is measured. The maximum proton energy is 21.7±0.2 MeV. Antimony isotopes yield in separate reactions when irradiating of tin isotopes with 100% enrichment is determined using the method published earlier. The methods for production of 117 Sb, 118m Sb, 120m Sb, 122 Sb, 124 Sb with high radioisotope purity are shown. 13 refs., 1 fig., 3 tabs

Tl, Bi, and Pb doping in Ba4BiPb2TlO12-δ

International Nuclear Information System (INIS)

Sutto, T.E.; Averill, B.A.

1992-01-01

To determine the effects of different 6s metal concentrations on the superconducting nature of Ba 4 BiPb 2 TlO 12-δ , materials produced via four doping schemes were examined: Ba 4 Bi(Pb, Tl) 3 O 12-δ , Ba 4 -(BiPb) 3 TlO 12-δ , Ba 4 (Bi,Tl) 2 Pb 2 O 12-δ , and Ba 4 Bi x Pb 4-2x Tl x O 12-δ . For the parent compound a value of δ = 0.91 was observed, indicating that approximately 1/4 oxygen atom was missing per cubic subsection of the unit cell. For all samples, the symmetry of the parent compound changed from orthorhombic to tetragonal as the system moved away from the ideal composition. This was usually accompanied by the loss of superconductivity, which exhibited a maximum T c of 10.5 K for the parent compound Ba 4 BiPb 2 TlO 12-δ . Also reported are high-temperature magnetic susceptibility results, which are used to determine the effect of metal substitution on the density of states at the Fermi level. For each set of variants on the parent composition, the onset of superconductivity was accompanied by a significant decrease in the size of the Pauli paramagnetic signal. 16 refs., 6 figs

Converting Hg-1212 to Tl-2212 via Tl-Hg cation exchange in combination with Tl cation intercalation

International Nuclear Information System (INIS)

Zhao Hua; Wu, Judy Z

2007-01-01

In a cation exchange process developed recently for epitaxy of HgBa 2 CaCu 2 O 6 (Hg-1212) thin films, TlBa 2 CaCu 2 O 7 (Tl-1212) or Tl 2 Ba 2 CaCu 2 O 9 (Tl-2212) precursor films were employed as the precursor matrices and Hg-1212 was obtained by replacing Tl cations on the precursor lattice with Hg cations. The reversibility of the cation exchange dictates directly the underlying mechanism. Following our recent success in demonstrating a complete reversibility within '1212' structure, we show the conversion from Hg-1212 to Tl-2212 can be achieved via two steps: conversion from Hg-1212 to Tl-1212 followed by Tl intercalation to form double Tl-O plans in each unit cell. The demonstrated reversibility of the cation exchange process has confirmed the process is a thermal perturbation of weakly bonded cations on the lattice and the direction of the process is determined by the population ratio between the replacing cations and that to be replaced

Natural quartz TL property and similarity in Piper nigrum L

International Nuclear Information System (INIS)

Guzman A, S.; Cruz Z, E.; Furetta, C.; Brown, F.; Barboza F, M.

2009-10-01

Quartz is a mineral abundant in nature and can provide information thermoluminescent (TL), and also is located in the mineral fraction of some herbs and spices consumed. It is present the analysis of the TL properties of a sample of natural quartz rock and compared with those obtained from the fraction of Piper nigrum L. poly mineral when they were exposed to 60 Co gamma radiation. The poly minerals of Piper nigrum L. were analyzed by X-ray diffraction, where the quartz was found as a major component. They separated in different particle sizes (10, 53, 74 and 149 μm). The samples were irradiated at relatively low doses (1-500 Gy) and high (0.1-40 kGy) in order to determine the linearity of the TL emission as a function of the dose and the analysis of glow curves. Also there was the fading of the TL signal, the effect of ultra violet light. The reproducibility of the TL signal in the samples indicates that a smaller particle size gives better TL signal. (author)

Kinetic parameters and TL mechanism in cadmium tetra borate phosphor

International Nuclear Information System (INIS)

Annalakshmi, O.; Jose, M.T.; Sridevi, J.; Venkatraman, B.; Amarendra, G.; Mandal, A.B.

2014-01-01

Polycrystalline powder samples of cadmium tetra borate were synthesized by a simple solid state sintering technique and gamma irradiated sample showed a simple Thermoluminescence (TL) glow peak around 460 K. The TL kinetic parameters of gamma irradiated phosphor were determined by initial rise (IR), isothermal decay (ID), peak shape (PS), variable heating rate (VHR) and glow curve de-convolution method. The kinetic parameters such as activation energy (E), frequency factor (s) and order of kinetics (b) were calculated by IR, ID, PS and VHR methods are in the order of ∼1.05 eV, 10 9 –10 12 s −1 and 1.58, respectively. From the results of TL and PL emission studies carried out on the phosphor revealed that the defect centers related to TL is different from that for PL. EPR measurements were carried out to identify the defect centers formed in cadmium tetra borate phosphor on gamma irradiation. Based on EPR studies the mechanism for TL process in cadmium tetra borate is proposed in this paper -- Highlights: • Polycrystalline powder samples of undoped cadmium tetra borate synthesized. • Cadmium tetra borate phosphor exhibits a dosimetric peak at 458 K. • Kinetic parameters of the trap responsible for TL evaluated. • TL mechanism is proposed from TL to EPR correlation studies

Kinetic parameters and TL mechanism in cadmium tetra borate phosphor

Energy Technology Data Exchange (ETDEWEB)

Annalakshmi, O. [Radiological Safety Division, Materials Physics Division, Indira Gandhi Centre for Atomic Research, Kalpakkam-603102 (India); Jose, M.T., E-mail: mtj@igcar.gov.in [Radiological Safety Division, Materials Physics Division, Indira Gandhi Centre for Atomic Research, Kalpakkam-603102 (India); Sridevi, J. [Central Leather Research Institute, Council of Scientific and Industrial Research, Chennai 600 020, Tamilnadhu (India); Venkatraman, B. [Radiological Safety Division, Materials Physics Division, Indira Gandhi Centre for Atomic Research, Kalpakkam-603102 (India); Amarendra, G. [Materials Physics Division, Indira Gandhi Centre for Atomic Research, Kalpakkam-603102 (India); Mandal, A.B. [Central Leather Research Institute, Council of Scientific and Industrial Research, Chennai 600 020, Tamilnadhu (India)

2014-03-15

Polycrystalline powder samples of cadmium tetra borate were synthesized by a simple solid state sintering technique and gamma irradiated sample showed a simple Thermoluminescence (TL) glow peak around 460 K. The TL kinetic parameters of gamma irradiated phosphor were determined by initial rise (IR), isothermal decay (ID), peak shape (PS), variable heating rate (VHR) and glow curve de-convolution method. The kinetic parameters such as activation energy (E), frequency factor (s) and order of kinetics (b) were calculated by IR, ID, PS and VHR methods are in the order of ∼1.05 eV, 10{sup 9}–10{sup 12} s{sup −1} and 1.58, respectively. From the results of TL and PL emission studies carried out on the phosphor revealed that the defect centers related to TL is different from that for PL. EPR measurements were carried out to identify the defect centers formed in cadmium tetra borate phosphor on gamma irradiation. Based on EPR studies the mechanism for TL process in cadmium tetra borate is proposed in this paper -- Highlights: • Polycrystalline powder samples of undoped cadmium tetra borate synthesized. • Cadmium tetra borate phosphor exhibits a dosimetric peak at 458 K. • Kinetic parameters of the trap responsible for TL evaluated. • TL mechanism is proposed from TL to EPR correlation studies.

Tl and OSL on diopside crystal

International Nuclear Information System (INIS)

Cano, N.F.; Watanabe, S.; Mittani, J.C.R.; Yukihara, E.G.

2006-01-01

The diopside with chemical composition CaMgSi 2 O 6 is part of an important solid solution series of the pyroxene group. The mineral is commonly found in meteorites and it is an important rock forming mineral of medium and high grade metamorphic rocks which are rich in calcium. In the bibliography it is possible to found several studies on electron spin resonance (ESR), reflectance, etc. but not on thermoluminescence (TL) or optically stimulated luminescence (OSL). In the present work we studied diopside TL and OSL behaviour on natural and natural irradiated samples. The sample used in our study is a white coloured diopside provided by Mineracao Sao Judas located in Sao Paulo, Brazil. The X-Ray Fluorescence technique has shown high concentrations of SiO 2 (55.81 % mol), CaO (23.47 % mol), MgO (18.03 % mol), Al 2 O 3 (1.56 % mol), Fe 2 O 3 (0.53 % mol), K 2 O (0.44 % mol), TiO 2 (0.065 % mol), P 2 O 5 (0.026 % mol), and MnO (0.013 % mol). TL measurements on natural samples show four TL peaks at 160, 260, 360, and 450 C. After beta-irradiation an increment mainly in the low temperature peaks is observed. As for OSL measurements, low OSL signal was observed on natural samples using blue light stimulation and UV detection. The intensity of the signal was observed to increase with the irradiation dose. (Author)

121Sb-NMR study of filled skutterudite CeOs4Sb12

International Nuclear Information System (INIS)

Yogi, M.; Niki, H.; Mukuda, H.; Kitaoka, Y.; Sugawara, H.; Sato, H.

2007-01-01

121 Sb nuclear magnetic resonance (NMR) of filled skutterudite compound CeOs 4 Sb 12 has been carried out to investigate a spin fluctuation below T∼25K. In spite of a powdered sample, many sharp peaks, similar to a data for single crystal, were observed because of an orientation of the sample from the anisotropy of the magnetization. A numerical calculation well reproduces resonance fields for Sb(1) sites with H parallel V zz . The nuclear spin-lattice relaxation rate divided by temperature 1/T 1 T shows continuous decrease with increasing magnetic field, indicating a suppression of the spin fluctuation by the field

In-homogeneity in the pre-dose sensitization of the 110 °C TL peak in various quartz samples: The influence of annealing

International Nuclear Information System (INIS)

Polymeris, George S.; Oniya, Ebenezer O.; Jibiri, Nnamdi N.; Tsirliganis, Nestor C.; Kitis, George

2012-01-01

The pre-dose sensitization effect of the 110 °C TL glow-peak of quartz is a basic tool in thermoluminescence and optically stimulated luminescence dating and retrospective dosimetry. In the present work, a homogeneity study was performed on pre-dose sensitization in grains obtained from large quartz crystals samples collected from 10 different origins. The aliquot – to – aliquot scatter of the pre-dose sensitization of the 110 °C TL peak within each quartz crystal was monitored. The influence of the annealing on this scattering was also studied. Therefore, the investigation was applied to the un-fired “as is” samples as well as to samples annealed at 900 °C for 1 h following cooling to room temperature in air. The results showed that in the case of “as is” quartz the sensitization effect vary strongly within each aliquot of the same quartz sample. This strong variation is removed by both the high temperature annealing as well as heating up to 500 °C, involved in the TL measurements. These results are generally discussed in the framework of existing models and applications of the effect.

Superconducting transition in TlBiTe/sub 2/ and TlTe compounds

Energy Technology Data Exchange (ETDEWEB)

Kantser, V G; Popovich, N S; Sidorenko, A S

1985-10-01

On the basis of zone structure calculation for TlBiTe/sub 2/ and TlTe it is found that TlBiTe/sub 2/ is a narrow-gap semiconductor and TlTe is a p-metal. At Tsub(c)=0.19 K TlTe is found to experience the superconducting transition. In TlBiTe/sub 2/ superconductivity is not observed to occur up to 0.05 K, since there is a possibility of occupying the high density of states zones because they are remote from actual ones. The earlier discovered superconducting transition in TlBiTe/sub 2/ is inherent in the alien phase of TlTe.

The use of thallium diethyldithiocarbamate for mapping CNS potassium metabolism and neuronal activity: Tl+ -redistribution, Tl+ -kinetics and Tl+ -equilibrium distribution.

Science.gov (United States)

Wanger, Tim; Scheich, Henning; Ohl, Frank W; Goldschmidt, Jürgen

2012-07-01

The potassium (K(+)) analogue thallium (Tl(+)) can be used as a tracer for mapping neuronal activity. However, because of the poor blood-brain barrier (BBB) K(+) -permeability, only minute amounts of Tl(+) enter the brain after systemic injection of Tl(+) -salts like thallium acetate (TlAc). We have recently shown that it is possible to overcome this limitation by injecting animals with the lipophilic chelate complex thallium diethyldithiocarbamate (TlDDC), that crosses the BBB and releases Tl(+) prior to neuronal or glial uptake. TlDDC can thus be used for mapping CNS K(+) metabolism and neuronal activity. Here, we analyze Tl(+) -kinetics in the rodent brain both experimentally and using simple mathematical models. We systemically injected animals either with TlAc or with TlDDC. Using an autometallographic method we mapped the brain Tl(+) -distribution at various time points after injection. We show that the patterns and kinetics of Tl(+) -redistribution in the brain are essentially the same irrespective of whether animals have been injected with TlAc or TlDDC. Data from modeling and experiments indicate that transmembrane Tl(+) -fluxes in cells within the CNS in vivo equilibrate at similar rates as K(+) -fluxes in vitro. This equilibration is much faster than and largely independent of the equilibration of Tl(+) -fluxes across the BBB. The study provides further proof-of-concept for the use of TlDDC for mapping neuronal activity and CNS K(+) -metabolism. A theoretical guideline is given for the use of K(+) -analogues for imaging neuronal activity with general implications for the use of metal ions in neuroimaging. © 2012 The Authors. Journal of Neurochemistry © 2012 International Society for Neurochemistry.

Limiting scattering processes in high-mobility InSb quantum wells grown on GaSb buffer systems

Science.gov (United States)

Lehner, Ch. A.; Tschirky, T.; Ihn, T.; Dietsche, W.; Keller, J.; Fält, S.; Wegscheider, W.

2018-05-01

We present molecular beam epitaxial grown single- and double-side δ -doped InAlSb/InSb quantum wells with varying distances down to 50 nm to the surface on GaSb metamorphic buffers. We analyze the surface morphology as well as the impact of the crystalline quality on the electron transport. Comparing growth on GaSb and GaAs substrates indicates that the structural integrity of our InSb quantum wells is solely determined by the growth conditions at the GaSb/InAlSb transition and the InAlSb barrier growth. The two-dimensional electron gas samples show high mobilities of up to 349 000 cm2/Vs at cryogenic temperatures and 58 000 cm2/Vs at room temperature. With the calculated Dingle ratio and a transport lifetime model, ionized impurities predominantly remote from the quantum well are identified as the dominant source of scattering events. The analysis of the well-pronounced Shubnikov-de Haas oscillations reveals a high spin-orbit coupling with an effective g -factor of -38.4 in our samples. Along with the smooth surfaces and long mean free paths demonstrated, our InSb quantum wells are increasingly competitive for nanoscale implementations of Majorana mode devices.

Polarity-dependent resistance switching in GeSbTe phase-change thin films : The importance of excess Sb in filament formation

NARCIS (Netherlands)

Pandian, Ramanathaswamy; Kooi, Bart J.; Oosthoek, Jasper L. M.; van den Dool, Pim; Palasantzas, George; Pauza, Andrew

2009-01-01

We show that polarity-dependent resistance switching in GeSbTe thin films depends strongly on Sb composition by comparing current-voltage characteristics in Sb-excess Ge(2)Sb(2+x)Te(5) and stoichiometric Ge(2)Sb(2)Te(5) samples. This type of switching in Ge(2)Sb(2+x)Te(5) films is reversible with

Stability of Tl-Ba-Ca-Cu-O Superconducting Thin Films

Energy Technology Data Exchange (ETDEWEB)

Siegal, M.P.; Overmyer, D.L.; Venturini, E.L.; Padilla, R.R.; Provencio, P.N.

1999-08-23

We report the stability of TlBa{sub 2}CaCu{sub 2}O{sub 7} (Tl-1212) and Tl{sub 2}Ba{sub 2}CaCu{sub 2}O{sub 8} (T1-2212) thin films and by inference, the stability of TlBa{sub 2}Ca{sub 2}Cu{sub 3}O{sub 9} (Tl-1223) and Tl{sub 2}Ba{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} (Tl-2223) thin films, under a variety of conditions. In general, we observe that the stability behavior of the single Tl-O layer materials (Tl-1212 and Tl-1223)are similar and the double Tl-O layer materials (Tl-2212 and Tl-2223) are similar. All films are stable with repeated thermal cycling to cryogenic temperatures. Films are also stable in acetone and methanol. Moisture degrades film quality rapidly, especially in the form of vapor. Tl-1212 is more sensitive to vapor than Tl-2212. These materials are stable to high temperatures in either N{sub 2}, similar to vacuum for the cuprates, and O{sub 2} ambients. While total degradation of properties (superconducting and structural) occur at the same temperatures for all phases, 600 C in N{sub 2} and 700 C in O{sub 2}, the onset of degradation occurs at somewhat lower temperatures for Tl-1212 than for Tl-2212 films. In all cases, sample degradation is associated with Tl depletion from the films.

In-homogeneity in the pre-dose sensitization of the 110 Degree-Sign C TL peak in various quartz samples: The influence of annealing

Energy Technology Data Exchange (ETDEWEB)

Polymeris, George S., E-mail: polymers@auth.gr [Laboratory of Radiation Applications and Archaeological Dating, Department of Archaeometry and Physicochemical Measurements, Cultural and Educational Technology Institute, Athena, Research and Innovation Center in Information, Communication and Knowledge Technologies, Tsimiski 58, GR-67100 Xanthi (Greece); ISIK University, Faculty of Science and Arts, Physics Department, Sile 34980, Istanbul (Turkey); Oniya, Ebenezer O. [Laboratory of Radiation Applications and Archaeological Dating, Department of Archaeometry and Physicochemical Measurements, Cultural and Educational Technology Institute, Athena, Research and Innovation Center in Information, Communication and Knowledge Technologies, Tsimiski 58, GR-67100 Xanthi (Greece); Physics and Electronics Department, Adekunle Ajasin University, PMB 01 Akungba Akoko (Nigeria); Jibiri, Nnamdi N. [Department of Physics, University of Ibadan, Ibadan (Nigeria); Tsirliganis, Nestor C. [Laboratory of Radiation Applications and Archaeological Dating, Department of Archaeometry and Physicochemical Measurements, Cultural and Educational Technology Institute, Athena, Research and Innovation Center in Information, Communication and Knowledge Technologies, Tsimiski 58, GR-67100 Xanthi (Greece); Kitis, George [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124 Thessaloniki (Greece)

2012-03-01

The pre-dose sensitization effect of the 110 Degree-Sign C TL glow-peak of quartz is a basic tool in thermoluminescence and optically stimulated luminescence dating and retrospective dosimetry. In the present work, a homogeneity study was performed on pre-dose sensitization in grains obtained from large quartz crystals samples collected from 10 different origins. The aliquot - to - aliquot scatter of the pre-dose sensitization of the 110 Degree-Sign C TL peak within each quartz crystal was monitored. The influence of the annealing on this scattering was also studied. Therefore, the investigation was applied to the un-fired 'as is' samples as well as to samples annealed at 900 Degree-Sign C for 1 h following cooling to room temperature in air. The results showed that in the case of 'as is' quartz the sensitization effect vary strongly within each aliquot of the same quartz sample. This strong variation is removed by both the high temperature annealing as well as heating up to 500 Degree-Sign C, involved in the TL measurements. These results are generally discussed in the framework of existing models and applications of the effect.

Gamma-radiation-induced change in the activation energy of TL traps in LiRbSO[sub 4]:Tl

Energy Technology Data Exchange (ETDEWEB)

Kassem, M.E.; El-Kolaly, M.A.; Al-Houty, L.I. (Qatar Univ., Doha (Qatar). Dept. of Physics)

1994-06-01

Thermoluminescence (TL) measurements were carried out for pure and doped LiRbSO[sub 4], with different concentrations of thallium (Tl). The glow-curve range of measurement is between room temperature up to 300[sup o]C. The radiation absorbed dose is in the range 56-3.2 x 10[sup 5] Gy. The results show that both pure and doped samples have glow peak temperatures that are dose dependent, and vary between 70-80[sup o]C and 140-170[sup o]C for pure and doped samples respectively. Doped samples display double peaks that increase with dopant concentration up to about 0.7% wt. The second peak which occurs at high temperature increases linearly with dose up to 4500 Gy. From the results it is proposed that LiRbSO[sub 4] doped with 0.7% Tl can be used for dosimetric purposes in this range. The activation energies of structural transitions are estimated and the results are discussed on the basis of radiation-induced stable dipoles in the random field system. (Author).

The TL and OSL study of hydroxyapatites for dosimetric applications

International Nuclear Information System (INIS)

Alencar, Marcus A. Vallim de

2009-01-01

The hydroxyapatite, the principal mineral component of the bone and tooth enamel, is one of the dosimetric materials that has distinguished itself in the high dose and accidents dosimetry, as well as in the dating, for the Electron Paramagnetic Resonance (EPR) technique. For this reason, the hydroxyapatite could also be used as Thermoluminescence (TL) and Optically Stimulated Luminescence (OSL) dosimeter in the dosimetry of high doses and accidents, and also in the archaeological and geological dating. This work presents a brief study of the TL and OSL behaviour of the B type synthetic carbonated hydroxyapatite, observing the possibility to use this material in TL and OSL dosimetry. The samples were irradiated to a dose of 100 Gy and 1000 Gy, and the TL and OSL measurements were obtained by the RISOE TL/OSL reader, model TL/OSL-DA-15B. The first results demonstrate the presence of three peaks in the TL glow curve in the temperatures of 100 deg C, 150 deg C and 280 deg C. The synthetic carbonated hydroxyapatite also presents an OSL signal when the sample is stimulated with blue light and a small OSL signal for stimulation with infrared light (IR). These results indicate the possibility of this synthetic carbonated hydroxyapatite to be used as dose indicator material using the TL and OSL techniques. (author)

Vortex states of Tl2Ba2CuO6+δ studied via 205Tl NMR at 2 tesla

International Nuclear Information System (INIS)

Itoh, Yutaka; Michioka, Chishiro; Yoshimura, Kazuyoshi; Hayashi, Akihiko; Ueda, Yutaka

2005-01-01

We report a 205 Tl NMR study of vortex states in an aligned polycrystalline sample of an overdoped high-T c superconductor, Tl 2 Ba 2 CuO 6+δ (Tc - 85 K), at a magnetic field of 2 T along the c axis. We observed an imperfect vortex lattice, so-called Bragg glass, at T=5 K, the coexistence of vortex solid and vortex liquid between 10 and 60 K, and vortex melting between 65 and 85 K. No evidence for local antiferromagnetic ordering at vortex cores was found for our sample. (author)

Comparison of TL profiles in recent sea cores

Energy Technology Data Exchange (ETDEWEB)

Castagnoli, G C; Bonino, G

1985-01-01

The thermoluminescence (TL) profile of different recent Tyrrhenian sea cores sampled at various intervals during the last centuries have been compared in order to check the reproducibility of the profiles and investigate the possibility of using the results for monitoring solar-terrestrial relations in the past. The satisfactory results obtained by comparison of two different cores in the time interval 1755-1969 A.D. has demonstrated: (a) the two TL profiles are correlated; (b) the 11 yr cycle corresponding to the main solar cycle is evident in both TL profiles.

Minimising the Spurious TL of Recently Fired Ceramics Using the Foil Technique

International Nuclear Information System (INIS)

Michael, C.T.; Zacharias, N.; Polikreti, K.; Pagonis, V.

1999-01-01

The new foil technique for measuring the natural dose in TL dating is briefly presented. In this technique very thin samples are made with the necessary plasticity to achieve the best heating contact between sample and heater plate. Measurements can then be made in vacuum and it is possible to use higher heating rates. The effect of the increase of the TL signal with the increase of the heating rate is presented. The foil technique reduces chemiluminescence and increases the TL signal. This allows the application of TL dating to be extended to lower limits (lower ages). These limits are determined by estimating quantitatively the effects of the sample preparation procedure on the induction of spurious TL (triboluminescence). Samples from a two year old ceramic vase were prepared with two different powder preparation procedures: (a) by using a hand drill with a common steel edge and (b) by crushing a piece using a vice. Measurements at a heating rate of 50 deg. C.s -1 were made. The two estimates of P (total dose) provide an estimate of age for each procedure. The age estimation for the vice prepared sample is about 30 years and for the drilled sample is higher than 120 years. It is suggested that the use of a drill for powder preparation be avoided, especially in TL dating and authenticity tests of recently fired ceramics (less than 500 years). (author)

TL and LOE dosimetric evaluation of diamond films exposed to beta and ultraviolet radiation; Evaluacion dosimetrica TL y LOE de peliculas de diamante expuestas a radiacion beta y ultravioleta

Energy Technology Data Exchange (ETDEWEB)

Preciado F, S.; Melendrez, R.; Chernov, V.; Barboza F, M. [Universidad de Sonora, A.P. 13 y A.P. 5-088, 83000 Hermosillo, Sonora (Mexico); Schreck, M. [Universitaet Augsburg, Institut fuer Physik D-86135 (Germany); Cruz Z, E. [ICN, UNAM, 04500 Mexico D.F. (Mexico)

2005-07-01

The diamond possesses a privileged position regarding other materials of great technological importance. Their applications go from the optics, microelectronics, metals industry, medicine and of course as dosemeter, in the registration and detection of ionizing and non ionizing radiation. In this work the results of TL/LOE obtained in two samples of diamond of 10 {mu}m thickness grown by the chemical vapor deposition method (CVD) assisted by microwave plasma. The films were deposited in a silicon substrate (001) starting from a mixture of gases composed of CH{sub 4}/H{sub 2} and 750 ppm of molecular nitrogen as dopant. The samples were exposed to beta radiation (Sr{sup 90}/ Y{sup 90}) and ultraviolet, being stimulated later on thermal (TL) and optically (LOE) to evaluate their dosimetric properties. The sample without doping presented high response TL/LOE to the ultraviolet and beta radiation. The TL glow curve of the sample without doping showed two TL peaks with second order kinetics in the range of 520 to 550 K, besides a peak with first order kinetics of more intensity around 607 K. The TL efficiency of the non doped sample is bigger than the doped with nitrogen; however the LOE efficiency is similar in both samples. The results indicate that the CVD diamond possesses excellent perspectives for dosimetric applications, with special importance in radiotherapy due to it is biologically compatible with the human tissue. (Author)

A Summary of Rheology Data For SB3 and SB2/3 Blend Simulant Savannah River Site Wastes

International Nuclear Information System (INIS)

KOOPMAN, DAVIDC.

2004-01-01

The purpose of this study was to document the rheological measurements made for Sludge Batch 3 (SB3) and the blend of SB3 with Sludge Batch 2 (SB2). These measurements were primarily made on Slurry Mix Evaporator (SME) products, i.e. melter feeds. Some measurements were made on SB2/3 blend Sludge Receipt and Adjustment Tank (SRAT) products. Measurements on radioactive SB3 and SB2/3 samples have been limited to sludge characterization. SB2/3 measurements studied the impact of changing the SRAT acid addition strategy on the SRAT and SME product rheology. SB2/3 measurements also studied the impact of changing the waste loading target (sludge oxides content in glass) of the SME product. SB3 measurements studied the impact of changes in the wash end point and acid addition strategy on the SME product (melter feed) rheology. A summary of the significant findings is given below: SB3 radioactive sludge and blended SB2/3 radioactive sludge were less viscous than SB2 radioactive sludge. SB2/3 b lend sludge is more viscous than SB3 sludge. SB3 simulant SME product rheology was strongly impacted by changing the noble metal concentrations to more closely match those of the qualification sample. This reduction in noble metals produced a lower pH product that was also considerably less viscous. Increased acid addition in the SB2/3 SRAT generally led to less viscous simulant SRAT products. This trend did not persist in the SME products. SME products became more viscous when increased acid was used in the SRAT cycle from 135 per cent up to 170 per cent of stoichiometry, then became less viscous as total acid was increased further to 185 per cent. A significant increase in hydrogen generation occurred between 170 per cent and 185 per cent. The impact of acid addition on SB3 SME products was also variable. The impact of waste loading changes from 31 to 35 to 40 per cent on SB2/3 simulant SME products led to more viscous melter feeds as waste loading increased at constant wt. per cent

Effect of Sb content on the thermoelectric properties of annealed CoSb_3 thin films deposited via RF co-sputtering

International Nuclear Information System (INIS)

Ahmed, Aziz; Han, Seungwoo

2017-01-01

Graphical abstract: The X-ray diffraction patterns and temperature dependence of the Seebeck coefficient of the annealed Co–Sb thin films. - Highlights: • CoSb_3 phase thin films were prepared using RF co sputtering method. • Thin film thermoelectric properties were hugely dependent on Sb content. • All thin films shows n-type conduction behavior at high temperatures. • The thin films with excess Sb possess the largest Seebeck coefficient. • The thin films with CoSb_2 phase possess the largest power factor. - Abstract: A series of CoSb_3 thin films with Sb contents in the range 70–79 at.% were deposited at room temperature via RF co-sputtering. The thin films were amorphous in the as-deposited state and annealed at 300 °C for 3 h to obtain crystalline samples. The annealed thin films were characterized using scanning electron microscopy and X-ray diffraction (XRD), and these data indicate that the films exhibited good crystallinity. The XRD patterns indicate single-phase CoSb_3 thin films in the Sb-rich samples. For the Sb-deficient samples, however, mixed-phase thin films consisting of CoSb_2 and CoSb_3 components were obtained. The electrical and thermoelectric properties were measured at temperatures up to 760 K and found to be highly sensitive to the phases that were present. We observed a change in the thermoelectric properties of the films from p-type at low temperatures to n-type at high temperatures, which indicates potential applications as n-type thermoelectric thin films. A large Seebeck coefficient and power factor was obtained for the single-phase CoSb_3 thin films. The CoSb_2 phase thin films were also found to possess a significant Seebeck coefficient, which coupled with the much smaller electrical resistivity, provided a larger power factor than the single-phase CoSb_3 thin films. We report maximum power factor of 7.92 mW/m K"2 for the CoSb_2-containing mixed phase thin film and 1.26 mW/m K"2 for the stoichiometric CoSb_3 thin film.

TL and ESR based identification of gamma-irradiated frozen fish using different hydrolysis techniques

Science.gov (United States)

Ahn, Jae-Jun; Akram, Kashif; Shahbaz, Hafiz Muhammad; Kwon, Joong-Ho

2014-12-01

Frozen fish fillets (walleye Pollack and Japanese Spanish mackerel) were selected as samples for irradiation (0-10 kGy) detection trials using different hydrolysis methods. Photostimulated luminescence (PSL)-based screening analysis for gamma-irradiated frozen fillets showed low sensitivity due to limited silicate mineral contents on the samples. Same limitations were found in the thermoluminescence (TL) analysis on mineral samples isolated by density separation method. However, acid (HCl) and alkali (KOH) hydrolysis methods were effective in getting enough minerals to carry out TL analysis, which was reconfirmed through the normalization step by calculating the TL ratios (TL1/TL2). For improved electron spin resonance (ESR) analysis, alkali and enzyme (alcalase) hydrolysis methods were compared in separating minute-bone fractions. The enzymatic method provided more clear radiation-specific hydroxyapatite radicals than that of the alkaline method. Different hydrolysis methods could extend the application of TL and ESR techniques in identifying the irradiation history of frozen fish fillets.

Synthesis and thermoelectric properties of Sb{sub 0.20}CoSb{sub 2.80} skutterudite

Energy Technology Data Exchange (ETDEWEB)

Figueirêdo, C.A., E-mail: camila_fig@hotmail.com [Universidade Federal do Rio Grande do Sul, PGCIMAT, Instituto de Física, 91501-970 Porto Alegre, RS (Brazil); Gallas, M.R. [Universidade Federal do Rio Grande do Sul, PGCIMAT, Instituto de Física, 91501-970 Porto Alegre, RS (Brazil); Institute for Multiscale Simulations, Friedrich-Alexander-Universität, Nägelsbachstrasse 49b, 91052 Erlangen (Germany); Zorzi, J.E. [Universidade de Caxias do Sul, Instituto de Materiais Cerâmicos, 95765-000 Bom Princípio, RS (Brazil); Perottoni, C.A. [Universidade Federal do Rio Grande do Sul, PGCIMAT, Instituto de Física, 91501-970 Porto Alegre, RS (Brazil); Universidade de Caxias do Sul, Instituto de Materiais Cerâmicos, 95765-000 Bom Princípio, RS (Brazil)

2014-06-15

Highlights: • A HP-HT Sb{sub 0.20}CoSb{sub 2.80} phase was prepared by processing cobalt antimonide at 7.7 GPa and 550 °C, for (at least) 5 min. • The mechanism of formation of this phase involves (i) decomposition of cobalt antimonide into CoSb{sub 2} and Sb, and (ii) insertion of Sb into the remaining cobalt antimonide. • The mechanism of formation is qualitatively different from that responsible for the formation of the high pressure (greater than 20 GPa) phase. - Abstract: Polycrystalline samples of cobalt antimonide (CoSb{sub 2.79}) were submitted to different conditions of pressure, temperature and processing time, in a high-pressure toroidal-type chamber, aiming to maximize the production of the high pressure phase previously observed in experiments with a diamond anvil cell. Rietveld refinements of X-ray powder diffraction data were performed to determine the phase composition and structural parameters. The maximum yield, 89(2) wt.% of Sb{sub x}CoSb{sub 3−x} phase, was obtained at 7.7 GPa, 550 °C and (at least) 5 min of processing time. The mechanism behind the formation of Sb{sub x}CoSb{sub 3−x} at high pressure and high temperature is actually not the same as that previously inferred from experiments at higher pressures (20 GPa) and room temperature with the diamond anvil cell. Indeed, evidences suggest that, at high pressure and high temperature, Sb{sub x}CoSb{sub 3−x} is formed by insertion of Sb resulting from decomposition of cobalt antimonide. Thermal conductivity, Seebeck coefficient and electrical conductivity were estimated for CoSb{sub 2.79} and Sb{sub 0.20}CoSb{sub 2.80}. The thermoelectric figure of merit at room temperature for Sb{sub 0.20}CoSb{sub 2.80} resulted 33% greater than that for CoSb{sub 2.79}.

Effect of Sb content on the thermoelectric properties of annealed CoSb{sub 3} thin films deposited via RF co-sputtering

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Aziz, E-mail: aziz_ahmed@ust.ac.kr [Department of Nano-Mechatronics, Korea University of Science and Technology (UST), 217 Gajeong-ro, Yuseong-gu, Daejeon, 305-350 (Korea, Republic of); Department of Nano-Mechanics, Korea Institute of Machinery and Materials (KIMM), 156 Gajeongbuk-ro, Yuseong-gu, Daejeon, 305-343 (Korea, Republic of); Han, Seungwoo, E-mail: swhan@kimm.re.kr [Department of Nano-Mechatronics, Korea University of Science and Technology (UST), 217 Gajeong-ro, Yuseong-gu, Daejeon, 305-350 (Korea, Republic of); Department of Nano-Mechanics, Korea Institute of Machinery and Materials (KIMM), 156 Gajeongbuk-ro, Yuseong-gu, Daejeon, 305-343 (Korea, Republic of)

2017-06-30

Graphical abstract: The X-ray diffraction patterns and temperature dependence of the Seebeck coefficient of the annealed Co–Sb thin films. - Highlights: • CoSb{sub 3} phase thin films were prepared using RF co sputtering method. • Thin film thermoelectric properties were hugely dependent on Sb content. • All thin films shows n-type conduction behavior at high temperatures. • The thin films with excess Sb possess the largest Seebeck coefficient. • The thin films with CoSb{sub 2} phase possess the largest power factor. - Abstract: A series of CoSb{sub 3} thin films with Sb contents in the range 70–79 at.% were deposited at room temperature via RF co-sputtering. The thin films were amorphous in the as-deposited state and annealed at 300 °C for 3 h to obtain crystalline samples. The annealed thin films were characterized using scanning electron microscopy and X-ray diffraction (XRD), and these data indicate that the films exhibited good crystallinity. The XRD patterns indicate single-phase CoSb{sub 3} thin films in the Sb-rich samples. For the Sb-deficient samples, however, mixed-phase thin films consisting of CoSb{sub 2} and CoSb{sub 3} components were obtained. The electrical and thermoelectric properties were measured at temperatures up to 760 K and found to be highly sensitive to the phases that were present. We observed a change in the thermoelectric properties of the films from p-type at low temperatures to n-type at high temperatures, which indicates potential applications as n-type thermoelectric thin films. A large Seebeck coefficient and power factor was obtained for the single-phase CoSb{sub 3} thin films. The CoSb{sub 2} phase thin films were also found to possess a significant Seebeck coefficient, which coupled with the much smaller electrical resistivity, provided a larger power factor than the single-phase CoSb{sub 3} thin films. We report maximum power factor of 7.92 mW/m K{sup 2} for the CoSb{sub 2}-containing mixed phase thin film and 1

TL response to quartz and aluminum oxide grain for α-irradiation

International Nuclear Information System (INIS)

Pan Baolin; Wei Mingjian; Li Dongxu; Liu Zhaowen; Liu Chao; Zhao Shiyuan

2009-01-01

Thermoluminescence (TL) response for an α-ray irradiation system ( 241 Am) was examined with quartz grains of 11-40 μm. Quartz grains of different sizes, i.e. 137 Cs), before they were irradiated to different doses by the α-ray irradiation system. TL response to the quartz grain samples was measured. TL response of the quartz grains smaller than 4 μm and 11-40 μm to α-ray irradiation is the best, as the α-rays cannot penetrate quartz larger than 40 μm. The TL response characteristic is related with quartz grain surface area. TL responses to α-irradiation of 11-40 μm quartz and aluminum oxide grains were compared. The α-irradiation TL response of aluminum oxide (330 degree C) is better than the quartz (375 degree C). (authors)

Auto-regenerative TL dating with zircon inclusions from fired materials

International Nuclear Information System (INIS)

Templer, R.H.; Smith, B.W.

1988-01-01

In this paper it is shown that it is possible to date fired material using zircon inclusions. The effects of zoning and anomalous fading are overcome using an auto-regenerative dating procedure. The high radioactivity of the grains gives a measurable self-induced TL (thermoluminescence) signal within a few months. Comparison of this ''auto-regenerated'' TL with the natural TL (which has accumulated since the firing) yields the age of the material. A sensitive TL reader capable of recording the auto-regenerated signal after 6 months is also described, and the results of age determinations on a number of known age samples are presented. (author)

TL and ESR based identification of gamma-irradiated frozen fish using different hydrolysis techniques

International Nuclear Information System (INIS)

Ahn, Jae-Jun; Akram, Kashif; Shahbaz, Hafiz Muhammad; Kwon, Joong-Ho

2014-01-01

Frozen fish fillets (walleye Pollack and Japanese Spanish mackerel) were selected as samples for irradiation (0–10 kGy) detection trials using different hydrolysis methods. Photostimulated luminescence (PSL)-based screening analysis for gamma-irradiated frozen fillets showed low sensitivity due to limited silicate mineral contents on the samples. Same limitations were found in the thermoluminescence (TL) analysis on mineral samples isolated by density separation method. However, acid (HCl) and alkali (KOH) hydrolysis methods were effective in getting enough minerals to carry out TL analysis, which was reconfirmed through the normalization step by calculating the TL ratios (TL 1 /TL 2 ). For improved electron spin resonance (ESR) analysis, alkali and enzyme (alcalase) hydrolysis methods were compared in separating minute-bone fractions. The enzymatic method provided more clear radiation-specific hydroxyapatite radicals than that of the alkaline method. Different hydrolysis methods could extend the application of TL and ESR techniques in identifying the irradiation history of frozen fish fillets. - Highlights: • Irradiation has potential to improve hygienic quality of raw and processed seafood. • Detection of irradiated food is important to enforce the applied regulations. • Different techniques were compared to separate silicate minerals from frozen fish. • Limitations were observed in TL analysis on minerals isolated by density separation. • Hydrolysis methods provided more clear identification using TL and ESR techniques

Area 3 Support Buildings (A3SB) H5-0992, H5-0996 PRL 218 Confirmatory Sampling Report

Science.gov (United States)

Mrdjenovich, Timothy

2015-01-01

The Area 3 Support Buildings site (A3SB) consists of two separate areas located on the north side of Beach Road in the northern portion of Kennedy Space Center, Florida (KSC), outside the secured perimeter of KSC. The A3SB areas are approximately 0.6 miles apart, and were developed as Shiffler's Grocery Store and Service Station (west site) and as a residence (east site) prior to acquisition by the National Aeronautics and Space Administration (NASA) in 1963. Both areas were used by the Bendix Company in support of NASA as chemical laboratories from 1963 through 1969. Both of the buildings were demolished by 1987. The west portion of the site was used by the US Fish & Wildlife Service (F&W) in support of the Merritt Island National Wildlife Refuge (MINWR) for parking at the entrance to the Hammock Trails from 1969 to the present. The east portion of the site was used for intermittent suspect materials staging in the early 1990s and is still used as an apiary location, but is otherwise no longer active. In support of the NASA HSWA permit requirements, this site was identified as Potential Release Location (PRL) 218 and a Solid Waste Management Unit (SWMU) Assessment (SA) was conducted in 2013. Confirmatory Sampling (CS) was recommended and approved by the KSC Remediation Team (KSCRT). Three locations of concern (LOCs) were identified and sampled at the site. The LOCs include two former chemical labs and a former suspect staging area. The CS was conducted in March of 2015 at three locations by means of Direct Push Technology (DPT) groundwater sampling and at one location for soil sampling. The samples were collected and analyzed in accordance with the approved CS Work Plan. There were no exceedances of criteria detected in any of the samples from the three LOCs. The results of this investigation indicate that past and/or present operations have not negatively impacted environmental media at the A3SB. Based upon no confirmed groundwater detections above GCTLs and no

Investigation and dating of gypsum crystals from Sivrihisar region in Eskisehir by ESR and TL techniques

International Nuclear Information System (INIS)

2011-01-01

Gypsum crystals taken from Sivrihisar-Eskisehir district were investigated and dated by Electron Spin Resonance (ESR) and Thermoluminescence (TL) techniques. The natural ESR spectra of gypsum samples had also the signals of Mn 2 + in addition to the signal at g=2.009. It was observed that the intensity of ESR signal at g=2.009 increased with gamma irradiation dose. This ESR signal (g=2.009) was used as a dating signal in dating of gypsum samples. The only one TL peak at about 278 degree Celsius was observed in TL glow curves of nonirradiated gypsum sample. In the case of irradiated sample, TL peak at 157 degree Celsius was observed in addition of TL peak at 278 degree Celsius. Gypsum samples were irradiated with a 6 0Co gamma source. The ESR spectra and TL glow curve of gypsum samples were recorded by X-band ESR spectrometer and Risφ TL/OSL reader, respectively. For samples, ESR/TL dose-response curves was constructed. Dose-response curves were fitted with an exponential saturation function. Based on this model, accumulated dose (AD) values for dating are determined. 2 38U, 2 32Th and 4 0K analysis was carried out for gypsum crystals and dolomite which enveloped these gypsum crystals. The internal dose rate was calculated from 2 38U, 2 32Th and 4 0K analysis results of gypsum sample. The external dose rate was calculated by using 2 38U, 2 32Th and 4 0K analysis results of dolomite and cosmic dose rate. Internal and external gamma dose-rate was used for dating calculations. Because of successive recrystallization of gypsum sample after formation, calculated age values of gypsum is smaller than expected formation age.

TL and LOE dosimetric evaluation of diamond films exposed to beta and ultraviolet radiation

International Nuclear Information System (INIS)

Preciado F, S.; Melendrez, R.; Chernov, V.; Barboza F, M.; Schreck, M.; Cruz Z, E.

2005-01-01

The diamond possesses a privileged position regarding other materials of great technological importance. Their applications go from the optics, microelectronics, metals industry, medicine and of course as dosemeter, in the registration and detection of ionizing and non ionizing radiation. In this work the results of TL/LOE obtained in two samples of diamond of 10 μm thickness grown by the chemical vapor deposition method (CVD) assisted by microwave plasma. The films were deposited in a silicon substrate (001) starting from a mixture of gases composed of CH 4 /H 2 and 750 ppm of molecular nitrogen as dopant. The samples were exposed to beta radiation (Sr 90 / Y 90 ) and ultraviolet, being stimulated later on thermal (TL) and optically (LOE) to evaluate their dosimetric properties. The sample without doping presented high response TL/LOE to the ultraviolet and beta radiation. The TL glow curve of the sample without doping showed two TL peaks with second order kinetics in the range of 520 to 550 K, besides a peak with first order kinetics of more intensity around 607 K. The TL efficiency of the non doped sample is bigger than the doped with nitrogen; however the LOE efficiency is similar in both samples. The results indicate that the CVD diamond possesses excellent perspectives for dosimetric applications, with special importance in radiotherapy due to it is biologically compatible with the human tissue. (Author)

TL transgenic mouse strains

International Nuclear Information System (INIS)

Obata, Y.; Matsudaira, Y.; Hasegawa, H.; Tamaki, H.; Takahashi, T.; Morita, A.; Kasai, K.

1993-01-01

As a result of abnormal development of the thymus of these mice, TCR αβ lineage of the T cell differentiation is disturbed and cells belonging to the TCR γδ CD4 - CD8 - double negative (DN) lineage become preponderant. The γδ DN cells migrate into peripheral lymphoid organs and constitute nearly 50% of peripheral T cells. Immune function of the transgenic mice is severely impaired, indicating that the γδ cells are incapable of participating in these reactions. Molecular and serological analyses of T-cell lymphomas reveal that they belong to the γδ lineage. Tg.Tla a -3-1 mice should be useful in defining the role of TL in normal and abnormal T cell differentiation as well as in the development of T-cell lymphomas, and further they should facilitate studies on the differentiation and function of γδ T cells. We isolated T3 b -TL gene from B6 mice and constructed a chimeric gene in which T3 b -TL is driven by the promoter of H-2K b . With the chimeric gene, two transgenic mouse strains, Tg. Con.3-1 and -2 have been derived in C3H background. Both strains express TL antigen in various tissues including skin. The skin graft of transgenic mice on C3H and (B6 X C3H)F 1 mice were rejected. In the mice which rejected the grafts, CD8 + TCRαβ cytotoxic T cells (CTL) against TL antigens were recognized. The recognition of TL by CTL did not require the antigen presentation by H-2 molecules. The results indicated that TL antigen in the skin becomes a transplantation antigen and behaves like a typical allogeneic MHC class I antigen. The facts that (B6 X C3H)F 1 mice rejected the skin expressing T3 b -TL antigen and induced CTL that killed TL + lymphomas of B6 origin revealed that TL antigen encoded by T3 b -TL is recognized as non-self in B6 mice. Experiments are now extended to analyze immune responses to TL antigen expressed on autochthonous T cell lymphomas. (J.P.N.)

Activation analysis of thallium by /sup 203/Tl(n,2n)/sup 202/Tl reaction in nuclear reactors

Energy Technology Data Exchange (ETDEWEB)

Cohen, I M; Resnizky, S M; Baro, G B [Comision Nacional de Energia Atomica, Buenos Aires (Argentina). Gerencia de Radioisotopos y Radiaciones

1982-01-01

Two techniques are described for neutron activation analysis of thallium in biological and geological materials, based on /sup 203/Tl(n,2n)/sup 202/Tl reaction in nuclear reactors. Co-precipitation with bismuth sulphide is used as a pre-concentration method of thallium in urine samples, and post-irradiation chemical separation is also performed. The detection limit is 0.5 ..mu..g/l, for 100 ml urine samples. For thallium determination in blendes a radiochemical separation is carried out after the irradiation. An extension of this technique is presented for glass and silicate rocks. Results for seven blende samples from different places of Argentina are shown. Analysis of two reference materials, the 614 glass from the National Bureau of Standards and the granodiorite GSP-1 from the U.S. Geological Survey were also performed. The results are in very good agreement with the certified or estimated values.

Comparison of the electrochemical performance of mesoscopic Cu2Sb, SnSb and Sn/SnSb alloy powders

International Nuclear Information System (INIS)

Zhang Ge; Huang Kelong; Liu Suqin; Zhang Wei; Gong Benli

2006-01-01

Cu 2 Sb, SnSb and Sn/SnSb mesoscopic alloy powders were prepared by chemical reduction, respectively. The crystal structures and particle morphology of Cu 2 Sb, SnSb and Sn/SnSb were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM). The electrochemical performances of the Cu 2 Sb, SnSb and Sn/SnSb electrodes were investigated by galvanostatic charge and discharge cycling and electrochemical impedance spectroscopy (EIS). The results showed the first charge and discharge capacities of SnSb and Sn/SnSb were higher than Cu 2 Sb, but after 15 cycles, the charge capacity fading rates of Cu 2 Sb, Sn/SnSb and Sn/SnSb were 26.16%, 55.33% and 47.39%, respectively. Cu 2 Sb had a better cycle performance, and Sn/SnSb multiphase alloy was prior to pure SnSb due to the existence of excessive Sn in Sn/SnSb system

Sand as in situ TL dosimeter in radiation hygienisation of sewage sludge

International Nuclear Information System (INIS)

Benny, P.G.; Bhatt, B.C.

1999-01-01

Recently, we have investigated the thermoluminescence (TL) properties of the sand, collected from the sewage sludge, after various extensive cleansing procedures. In the present studies, the sand separated from the sludge was used to estimate irradiation dose to sludge at Sludge Hygienisation Research Irradiator (SHRI), Vadodara, India. A dose vs TL response calibration curve was established for the 220 deg. C TL peak for the hydrogen peroxide (H 2 O 2 )-treated and HF-treated sludge sand samples collected from the unirradiated batch. This was used to estimate the dose absorbed in the corresponding batch of the irradiated sludge. Similar curve was plotted for the 370 deg. C TL peak for the HF-treated sand samples for its application as an in-situ dosimeter. Using this method, the absorbed dose rate delivered to the sludge during irradiation at SHRI was estimated to be 0.49 ± 0.02 kGy per hour. Also, the saturation levels of the TL response curves for these peaks are reported here. (author)

Tl Cuprate Superconductors Studied by XPS

Energy Technology Data Exchange (ETDEWEB)

Vasquez, R. P. [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109-8099 (United States); Siegal, M. P. [Sandia National Laboratories, Albuquerque, NM 87185-1421 (United States); Overmyer, D. L. [Sandia National Laboratories, Albuquerque, NM 87185-1421 (United States); Ren, Z. F. [Department of Chemistry, State University of New York, Buffalo, NY 14260-3000 (United States); Lao, J. Y. [Department of Chemistry, State University of New York, Buffalo, NY 14260-3000 (United States); Wang, J. H. [Department of Chemistry, State University of New York, Buffalo, NY 14260-3000 (United States)

1999-07-01

XPS measurements on epitaxial thin films of the Tl cuprate superconductors Tl2Ba2CaCu2O8, Tl2Ba2Ca2Cu3O10, and Tl0.78Bi0.22Ba0.4Sr1.6Ca2Cu3O9-{delta} are presented. These data, together with previous measurements in this lab on Tl2Ba2CuO6-{delta} and TlBa2CaCu2O7-{delta}, comprise a comprehensive data set for comparison of Tl cuprates in which the number of Tl-O and Cu-O layers, and hence the chemical and electronic properties, vary. (c) 2000 American Vacuum Society.

Tl Cuprate Superconductors Studied by XPS

International Nuclear Information System (INIS)

Vasquez, R. P.; Siegal, M. P.; Overmyer, D. L.; Ren, Z. F.; Lao, J. Y.; Wang, J. H.

1999-01-01

XPS measurements on epitaxial thin films of the Tl cuprate superconductors Tl2Ba2CaCu2O8, Tl2Ba2Ca2Cu3O10, and Tl0.78Bi0.22Ba0.4Sr1.6Ca2Cu3O9-δ are presented. These data, together with previous measurements in this lab on Tl2Ba2CuO6-δ and TlBa2CaCu2O7-δ, comprise a comprehensive data set for comparison of Tl cuprates in which the number of Tl-O and Cu-O layers, and hence the chemical and electronic properties, vary. (c) 2000 American Vacuum Society

Identification of irradiated spices by the use of thermoluminescence method (TL)

Energy Technology Data Exchange (ETDEWEB)

Sharifzadeh, M.; Sohrabpour, M. (Atomic Energy Organization of Iran, Teheran (Iran, Islamic Republic of))

In this paper the results of the investigation of identification of irradiated spices by the use of thermoluminescence method is reported. The materials used were black and red peppers, turmeric, cinnamon, and garlic powder. Gamma Cell 220 was used for irradiating samples at dose values of 2.5, 5, 7.5 and 10 kGy respectively. The TL intensity of the unirradiated spices as well as the fading characteristics of the irradiated samples having received a dose of 10 kGy have been measured. Post-irradiation temperature treatment of the irradiated (10 kGy) and unirradiated samples at 60[sup o]C and 100[sup o]C for 24 hours have also been performed. The results show that the TL intensities of unirradiated and irradiated samples from different batches of each spice are fairly distributed. A reasonable TL intensity versus dose has been observed in nearly all cases. Based on the observation made it is possible to distinguish irradiated spices after (4-9) months post-irradiation. (author).

Identification of irradiated spices by the use of thermoluminescence method (TL)

International Nuclear Information System (INIS)

Sharifzadeh, M.; Sohrabpour, M.

1993-01-01

In this paper the results of the investigation of identification of irradiated spices by the use of thermoluminescence method is reported. The materials used were black and red peppers, turmeric, cinnamon, and garlic powder. Gamma Cell 220 was used for irradiating samples at dose values of 2.5, 5, 7.5 and 10 kGy respectively. The TL intensity of the unirradiated spices as well as the fading characteristics of the irradiated samples having received a dose of 10 kGy have been measured. Post-irradiation temperature treatment of the irradiated (10 kGy) and unirradiated samples at 60 o C and 100 o C for 24 hours have also been performed. The results show that the TL intensities of unirradiated and irradiated samples from different batches of each spice are fairly distributed. A reasonable TL intensity versus dose has been observed in nearly all cases. Based on the observation made it is possible to distinguish irradiated spices after (4-9) months post-irradiation. (author)

Optical and structural characterization of GaSb and Te-doped GaSb single crystals

International Nuclear Information System (INIS)

Tirado-Mejia, L.; Villada, J.A.; Rios, M. de los; Penafiel, J.A.; Fonthal, G.; Espinosa-Arbelaez, D.G.; Ariza-Calderon, H.; Rodriguez-Garcia, M.E.

2008-01-01

Optical and structural properties of GaSb and Te-doped GaSb single crystals are reported herein. Utilizing the photoreflectance technique, the band gap energy for doped samples was obtained at 0.814 eV. Photoluminescence (PL) spectra showed a peak at 0.748 eV that according to this research, belongs to electronic states of pure GaSb and not to the longitudinal optical (LO) phonon replica as has been reported by other authors. Analysis of the full width at half maximum (FWHM) values of X-ray diffraction, as well as micro-Raman peaks showed that the inclusion of Te decreases the crystalline quality

Chemical bonding in Tl cuprates studied by x-ray photoemission

International Nuclear Information System (INIS)

Vasquez, R.P.; Siegal, M.P.; Overmyer, D.L.; Ren, Z.F.; Lao, J.Y.; Wang, J.H.

1999-01-01

Epitaxial thin films of the Tl cuprate superconductors Tl 2 Ba 2 CaCu 2 O 8 , Tl 2 Ba 2 Ca 2 Cu 3 O 10 , and Tl 0.78 Bi 0.22 Ba 0.4 Sr 1.6 Ca 2 Cu 3 O 9-δ are studied with x-ray photoemission spectroscopy. These data, together with previous measurements in this lab of Tl 2 Ba 2 CuO 6+δ and TlBa 2 CaCu 2 O 7-δ , comprise a comprehensive data set for a comparative study of Tl cuprates with a range of chemical and electronic properties. In the Cu 2p spectra, a larger energy separation between the satellite and main peaks (E s -E m ) and a lower intensity ratio (I s /I m ) are found to correlate with higher values of T c . Analysis of these spectra within a simple configuration interaction model suggests that higher values of T c are related to low values of the O 2p→Cu 3d charge transfer energy. In the O 1s region, a smaller bond length between Ba and Cu-O planar oxygen is found to correlate with a lower binding energy for the signal associated with Cu-O bonding, most likely resulting from the increased polarization screening by Ba 2+ ions. For samples near optimum doping, maximum T c is observed to occur when the Tl 4f 7/2 binding energy is near 117.9 eV, which is near the middle of the range of values observed for Tl cuprates. Higher Tl 4f 7/2 binding energies, corresponding to formal oxidation states nearer Tl 1+ , are also found to correlate with longer bond lengths between Ba and Tl-O planar oxygen, and with higher binding energies of the O 1s signal associated with Tl-O bonding. copyright 1999 The American Physical Society

Local structure and influence of bonding on the phase-change behavior of the chalcogenide compounds K{sub 1-} {sub x} Rb {sub x} Sb{sub 5}S{sub 8}

Energy Technology Data Exchange (ETDEWEB)

Wachter, J B [Department of Chemistry, Michigan State University, East Lansing, MI 48824 (United States); Chrissafis, K [Department of Physics, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Petkov, V [Department of Physics, Central Michigan University, Mount Pleasant, MI 48859 (United States); Malliakas, C D [Department of Chemistry, Michigan State University, East Lansing, MI 48824 (United States); Bilc, D [Department of Physics, Central Michigan University, Mount Pleasant, MI 48859 (United States); Kyratsi, Th [Department of Chemistry, Michigan State University, East Lansing, MI 48824 (United States); Paraskevopoulos, K M [Department of Physics, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Mahanti, S D [Department of Physics, Michigan State University, East Lansing, MI 48824 (United States); Torbruegge, T [Institut fuer Physikalische Chemie, Westf. Wilhelms-Universitaet Muenster (Germany); Eckert, H [Institut fuer Physikalische Chemie, Westf. Wilhelms-Universitaet Muenster (Germany); Kanatzidis, M.G. [Department of Chemistry, Michigan State University, East Lansing, MI 48824 (United States)], E-mail: m-kanatzidis@northwestern.edu

2007-02-15

KSb{sub 5}S{sub 8} and its solid solution analogs with Rb and Tl were found to exhibit a reversible and tunable glass{sup {yields}}crystal{sup {yields}}glass phase transition. Selected members of this series were analyzed by differential scanning calorimetry to measure the effect of the substitution on the thermal properties. The solid solutions K{sub 1-} {sub x} Rb {sub x} Sb{sub 5}S{sub 8} exhibited clear deviations in melting and crystallization behavior and temperatures from the parent structure. The crystallization process of the glassy KSb{sub 5}S{sub 8} as a function of temperature could clearly be followed with Raman spectroscopy. The thermal conductivity of both glassy and crystalline KSb{sub 5}S{sub 8} at room temperature is {approx}0.40 W/m K, among the lowest known values for any dense solid-state material. Electronic band structure calculations carried out on KSb{sub 5}S{sub 8} and TlSb{sub 5}S{sub 8} show the presence of large indirect band-gaps and confirm the coexistence of covalent Sb-S bonding and predominantly ionic K(Tl)...S bonding. Pair distribution function analyses based on total X-ray scattering data on both crystalline and glassy K{sub 1-} {sub x} Rb {sub x} Sb{sub 5}S{sub 8} showed that the basic structure-defining unit is the same and it involves a distorted polyhedron of 'SbS{sub 7}' fragment of {approx}7 A diameter. The similarity of local structure between the glassy and crystalline phases accounts for the facile crystallization rate in this system. - Graphical abstract: The KSb{sub 5}S{sub 8} is a good example of a phase-change material with a mixed ionic/covalent bonding. The members of the K{sub 1-} {sub x} Rb {sub x} Sb{sub 5}S{sub 8} series exhibit phase-change properties with greater glass forming ability (GFA) than KSb{sub 5}S{sub 8}. The GFA increases with increasing Rb content. In this case, the random alloy disorder in the alkali metal sublattice seems to predominate over the increased degree of ionicity in going from K

TL dating of pottery sherds and baked soil from the Xian Terracotta Army Site, Shaanxi Province, China

International Nuclear Information System (INIS)

Lu Yanchou; Zhang Jingzhao; Xie Jun

1988-01-01

Six ceramics and two baked soil samples collected from the famous Xian Terracotta Army Site have been dated by using fine grain (2-8 μ) thermoluminescence (TL) technique. Five samples of pottery sherds exhibited peak TL at about 275 0 C and 395 0 C gave the TL age ranges from 2.13 ± 0.14 ka to 2.25 ± 0.14 ka and a mean TL age of 2.20 ± 0.15 ka, with a good plateau in the range of 290-400 0 C. Another sample, however, showed a larger peak at 365 0 C and could not be dated because of serious fading. TL ages of 1.93 ± 0.13 ka and 2.20 ± 0.19 ka have been also obtained from the baked soil samples with a plateau between 300 and 350 0 C. The TL dates of the ceramics and baked soil are consistent with C-14 dates on charcoal samples taken from the same layer in Xian Terracotta Army Site. It is consistent with other evidence that the Terracotta Army figures were made about 2200 yr ago and that the site burned down soon afterwards. (author)

Point defect balance in epitaxial GaSb

International Nuclear Information System (INIS)

Segercrantz, N.; Slotte, J.; Makkonen, I.; Kujala, J.; Tuomisto, F.; Song, Y.; Wang, S.

2014-01-01

Positron annihilation spectroscopy in both conventional and coincidence Doppler broadening mode is used for studying the effect of growth conditions on the point defect balance in GaSb:Bi epitaxial layers grown by molecular beam epitaxy. Positron annihilation characteristics in GaSb are also calculated using density functional theory and compared to experimental results. We conclude that while the main positron trapping defect in bulk samples is the Ga antisite, the Ga vacancy is the most prominent trap in the samples grown by molecular beam epitaxy. The results suggest that the p–type conductivity is caused by different defects in GaSb grown with different methods.

Evidence for charge Kondo effect in superconducting Tl-doped PbTe

Energy Technology Data Exchange (ETDEWEB)

Fisher, I

2010-01-11

We report results of low-temperature thermodynamic and transport measurements of Pb{sub 1-x}Tl{sub x}Te single crystals for Tl concentrations up to the solubility limit of approximately x = 1.5%. For all doped samples, we observe a low-temperature resistivity upturn that scales in magnitude with the Tl concentration. The temperature and field dependence of this upturn are consistent with a charge Kondo effect involving degenerate Tl valence states differing by two electrons, with a characteristic Kondo temperature T{sub K} {approx} 6 K. The observation of such an effect supports an electronic pairing mechanism for superconductivity in this material and may account for the anomalously high T{sub c} values.

The precise measurement of TL isotopic compositions by MC-ICPMS: Application to the analysis of geological materials and meteorites.

Science.gov (United States)

Rehkämper, Mark; Halliday, Alex N.

1999-07-01

The precision of Tl isotopic measurements by thermal ionization mass spectrometry (TIMS) is severely limited by the fact that Tl possesses only two naturally occurring isotopes, such that there is no invariant isotope ratio that can be used to correct for instrumental mass discrimination. In this paper we describe new chemical and mass spectrometric techniques for the determination of Tl isotopic compositions at a level of precision hitherto unattained. Thallium is first separated from the geological matrix using a two-stage anion-exchange procedure. Thallium isotopic compositions are then determined by multiple-collector inductively coupled plasma-mass spectrometry with correction for mass discrimination using the known isotopic composition of Pb that is admixed to the sample solutions. With these procedures we achieve a precision of 0.01-0.02% for Tl isotope ratio measurements in geological samples and this is a factor of ≥3-4 better than the best published results by TIMS. However, without adequate precautions, experimental artifacts can be generated that result in apparent Tl isotopic fractionations of up to one per mil. Analysis of five terrestrial samples indicate the existence of Tl isotopic variations related to natural fractionation processes on the Earth. Two of the three igneous rocks analyzed in this study display Tl isotopic compositions indistinguishable from our laboratory standard, the reference material NIST-997 Tl. A third sample, however, is characterized by ɛ Tl ≈ 2.5 ± 1.5, where ɛ Tl represents the deviation of the 205Tl/ 203Tl ratio of the sample relative to NIST-997 Tl in parts per 10 4. Even larger deviations were identified for two ferromanganese crusts from the Pacific Ocean, which display ɛ Tl-values of +5.0 ± 1.5 and +11.7 ± 1.3. We suggest that the large variability of Tl isotopic compositions in the latter samples are caused by low-temperature processes related to the formation of the Fe-Mn crusts by precipitation and

Thermoelectric properties and microstructure of Mg3Sb2

International Nuclear Information System (INIS)

Condron, Cathie L.; Kauzlarich, Susan M.; Gascoin, Franck; Snyder, G. Jeffrey

2006-01-01

Mg 3 Sb 2 has been prepared by direct reaction of the elements. Powder X-ray diffraction, thermal gravimetric, differential scanning calorimetery, and microprobe data were obtained on hot pressed samples. Single phase samples of Mg 3 Sb 2 were prepared and found to contain oxygen at the grain boundaries and to lose Mg and oxidize at temperatures above 900 K. Thermoelectric properties were characterized by Seebeck, electrical resistivity, and thermal conductivity measurements from 300 to 1023 K, and the maximum zT was found to be 0.21 at ∼875 K. - Graphical abstract: Dimensionless figure of merit for Mg 3 Sb 2 hot pressed and sintered at 873 K. The inset illustrates the crystal structure of Mg 3 Sb 2 along the [100] direction (white=Mg, black=Sb)

Slurry sampling flow injection chemical vapor generation inductively coupled plasma mass spectrometry for the determination of trace Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions

Energy Technology Data Exchange (ETDEWEB)

Chen, Wei-Ni [Department of Chemistry, National Sun Yat-sen University, Kaohsiung 80424, Taiwan (China); Jiang, Shiuh-Jen, E-mail: sjjiang@faculty.nsysu.edu.tw [Department of Chemistry, National Sun Yat-sen University, Kaohsiung 80424, Taiwan (China); Department of Medical Laboratory Science and Biotechnology, Kaohsiung Medical University, Kaohsiung 80708, Taiwan (China); Chen, Yen-Ling [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, Kaohsiung 80708, Taiwan (China); Sahayam, A.C. [National Centre for Compositional Characterisation of Materials (CCCM), Hyderabad (India)

2015-02-20

Highlights: • Determination of Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions in a single run. • Accurate analysis using isotope dilution and standard addition methods. • Vapor generation ICP-MS yielded superior detection limits compared to ETV-ICP-MS. • No sample dissolution increased sample through put. • Analysis of GBW09305 Cosmetic (Cream) reference material for accuracy. - Abstract: A slurry sampling inductively coupled plasma mass spectrometry (ICP-MS) method has been developed for the determination of Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions using flow injection (FI) vapor generation (VG) as the sample introduction system. A slurry containing 2% m/v lotion, 2% m/v thiourea, 0.05% m/v L-cysteine, 0.5 μg mL{sup −1} Co(II), 0.1% m/v Triton X-100 and 1.2% v/v HCl was injected into a VG-ICP-MS system for the determination of Ge, As, Cd, Sb, Hg and Bi without dissolution and mineralization. Because the sensitivities of the analytes in the slurry and that of aqueous solution were quite different, an isotope dilution method and a standard addition method were used for the determination. This method has been validated by the determination of Ge, As, Cd, Sb, Hg and Bi in GBW09305 Cosmetic (Cream) reference material. The method was also applied for the determination of Ge, As, Cd, Sb, Hg and Bi in three cosmetic lotion samples obtained locally. The analysis results of the reference material agreed with the certified value and/or ETV-ICP-MS results. The detection limit estimated from the standard addition curve was 0.025, 0.1, 0.2, 0.1, 0.15, and 0.03 ng g{sup −1} for Ge, As, Cd, Sb, Hg and Bi, respectively, in original cosmetic lotion sample.

Slurry sampling flow injection chemical vapor generation inductively coupled plasma mass spectrometry for the determination of trace Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions

International Nuclear Information System (INIS)

Chen, Wei-Ni; Jiang, Shiuh-Jen; Chen, Yen-Ling; Sahayam, A.C.

2015-01-01

Highlights: • Determination of Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions in a single run. • Accurate analysis using isotope dilution and standard addition methods. • Vapor generation ICP-MS yielded superior detection limits compared to ETV-ICP-MS. • No sample dissolution increased sample through put. • Analysis of GBW09305 Cosmetic (Cream) reference material for accuracy. - Abstract: A slurry sampling inductively coupled plasma mass spectrometry (ICP-MS) method has been developed for the determination of Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions using flow injection (FI) vapor generation (VG) as the sample introduction system. A slurry containing 2% m/v lotion, 2% m/v thiourea, 0.05% m/v L-cysteine, 0.5 μg mL −1 Co(II), 0.1% m/v Triton X-100 and 1.2% v/v HCl was injected into a VG-ICP-MS system for the determination of Ge, As, Cd, Sb, Hg and Bi without dissolution and mineralization. Because the sensitivities of the analytes in the slurry and that of aqueous solution were quite different, an isotope dilution method and a standard addition method were used for the determination. This method has been validated by the determination of Ge, As, Cd, Sb, Hg and Bi in GBW09305 Cosmetic (Cream) reference material. The method was also applied for the determination of Ge, As, Cd, Sb, Hg and Bi in three cosmetic lotion samples obtained locally. The analysis results of the reference material agreed with the certified value and/or ETV-ICP-MS results. The detection limit estimated from the standard addition curve was 0.025, 0.1, 0.2, 0.1, 0.15, and 0.03 ng g −1 for Ge, As, Cd, Sb, Hg and Bi, respectively, in original cosmetic lotion sample

Isotopic exchange in a neutron-irradiated mixed-valence compound: Tl3(I) Tl(III)Cl6

International Nuclear Information System (INIS)

Fernandez Valverde, S.; Duplatre, G.

1977-01-01

The initial distribution of Tl(I) and Tl(III) species, and its change on heating, have been investigated in solid thermal neutron-irradiated Th 4 Cl 6 . An initial ratio of 5/1 for 204 Tl(I)/ 204 Tl(III) is found and this remains constant for integral gamma-doses of 3 to 12 MRad. The variation of the 204 Tl(III) fraction with temperature is found identical to that observed in labelled Tl 4 Cl 6 for which a genuine isotopic exchange has previously been described. It is concluded that the recoil species are rapidly converted, after the recoil processes, into stable ions

Syntheses, and crystal and electronic structures of the new Zintl phases Na2ACdSb2 and K2ACdSb2 (A=Ca, Sr, Ba, Eu, Yb): Structural relationship with Yb2CdSb2 and the solid solutions Sr2-xAxCdSb2, Ba2-xAxCdSb2 and Eu2-xYbxCdSb2

International Nuclear Information System (INIS)

Saparov, Bayrammurad; Saito, Maia; Bobev, Svilen

2011-01-01

Presented are the details of the syntheses, crystal and electronic structures of a new family of Zintl phases Na 2 ACdSb 2 and K 2 ACdSb 2 (A=Ca, Sr, Ba, Eu, Yb), as well as the solid solutions Sr 2-x A x CdSb 2 , Ba 2-x A x CdSb 2 and Eu 2-x Yb x CdSb 2 . The structures of Na 2 ACdSb 2 and K 2 ACdSb 2 (A=Ca, Sr, Ba, Eu, Yb) were determined to be of a new type with the non-centrosymmetric space group Pmc2 1 (no. 26), Pearson symbol oP12, with lattice parameters a=4.684(1)-4.788(1) A; b=9.099(3)-9.117(2) A; c=7.837(1)-8.057(2) A for the Na 2 ACdSb 2 series, and a=4.6637(9)-5.0368(8) A; b=9.100(2)-9.8183(15) A; and c=7.7954(15)-8.4924(13) A for K 2 ACdSb 2 , respectively. The solid solutions Sr 2-x A x CdSb 2 , Ba 2-x A x CdSb 2 and Eu 2-x Yb x CdSb 2 (x∼1) are isostructural and isoelectronic to the recently reported Yb 2 CdSb 2 (space group Cmc2 1 (no. 36), Pearson symbol cP20). All discussed structures are based upon CdSb 2 4- polyanionic layers, similar to the ones observed in Yb 2 CdSb 2 , with various alkali- and/or alkaline-earth cations coordinated to them. Magnetic susceptibility and Seebeck coefficient measurements on selected Eu 2-x Yb x CdSb 2 samples, taken at low temperatures up to 300 K, are also reported. -- Graphical abstract: The quaternary Zintl phases Na 2 ACdSb 2 and K 2 ACdSb 2 (A=Ca, Sr, Ba, Eu, Yb) with novel layered structures have been synthesized for the first time and structurally characterized by single-crystal X-ray diffraction. Reported as well are the results from crystallographic and property studies of the closely related solid solutions Sr 2-x A x CdSb 2 , Ba 2-x A x CdSb 2 (x∼1), and Eu 2-x Yb x CdSb 2 (1 2 ACdSb 2 and K 2 ACdSb 2 (A=Ca, Sr, Ba, Eu, Yb) are new quaternary Zintl phases. → Sr 2-x A x CdSb 2 , Ba 2-x A x CdSb 2 (x∼1), and Eu 2-x Yb x CdSb 2 (1 4 tetrahedra. → Eu 2-x Yb x CdSb 2 (1< x<2) exhibit high Seebeck coefficient (217 μV/K at RT).

Reactivity and stability of thallium oxide for fabricating TlSnZnO toward thin-film transistors with high mobility

Energy Technology Data Exchange (ETDEWEB)

Kishimoto, Katsushi [Graduate School of Materials Science, Nara Institute of Science and Technology, Nara, 630-0192 (Japan); Nose, Yoshitaro [Department of Materials Science and Engineering, Kyoto University, Kyoto, 606-8501 (Japan); Ishikawa, Yasuaki, E-mail: yishikawa@ms.naist.jp [Graduate School of Materials Science, Nara Institute of Science and Technology, Nara, 630-0192 (Japan); Fujii, Mami N.; Uraoka, Yukiharu [Graduate School of Materials Science, Nara Institute of Science and Technology, Nara, 630-0192 (Japan)

2016-07-05

Thermal reaction between thallium oxide (Tl{sub 2}O{sub 3}) and zinc oxide (ZnO), tin oxide (SnO{sub 2}) or indium oxide (In{sub 2}O{sub 3}) annealed at 600 °C for 18 h in the air atmosphere was investigated. From XRD results of 600 °C annealed samples, Tl{sub 2}O{sub 3} had the biggest reactivity compared with ZnO. The EDX results suggest the mechanism in which the thallium atoms scattered and attached uniformly only on ZnO particles. We also analyzed XPS data to compare O 1s bond and Tl 4f bond of as-mixed samples with that of annealed samples, and found that Zn and Sn can contribute in improving Tl and O bonding stability. However, the affinity of In for Tl is weaker than that of Zn or Sn. Finally, we prepared the samples mixed with ZnO, SnO{sub 2}, and Tl{sub 2}O{sub 3} powder and the samples mixed with Zn{sub 2}SnO{sub 4} and Tl{sub 2}O{sub 3} powder annealed at 600 °C for 18 h. Results show that Zn{sub 2}SnO{sub 4} has the same or more reactivity than SnO{sub 2} and ZnO mixed particle despite of the more stable and sufficient dispersion of Zn and Sn atoms. More stable TlSnZnO can be fabricated from Zn{sub 2}SnO{sub 4} + Tl{sub 2}O{sub 3} powder by suitable thermal processes. It is expected that TlSnZnO sputtering target can be fabricated by suitable calcination. - Highlights: • Thermal reaction of Tl{sub 2}O{sub 3} and ZnO, SnO or In{sub 2}O{sub 3} were investigate. • It is found that Tl{sub 2}O{sub 3} is reactive with ZnO rather than SnO or In{sub 2}O{sub 3}. • Two-step annealing process is promising route for forming TlSnZnO tablet.

Thermal Stability of Zone Melting p-Type (Bi, Sb)2Te3 Ingots and Comparison with the Corresponding Powder Metallurgy Samples

Science.gov (United States)

Jiang, Chengpeng; Fan, Xi'an; Hu, Jie; Feng, Bo; Xiang, Qiusheng; Li, Guangqiang; Li, Yawei; He, Zhu

2018-04-01

During the past few decades, Bi2Te3-based alloys have been investigated extensively because of their promising application in the area of low temperature waste heat thermoelectric power generation. However, their thermal stability must be evaluated to explore the appropriate service temperature. In this work, the thermal stability of zone melting p-type (Bi, Sb)2Te3-based ingots was investigated under different annealing treatment conditions. The effect of service temperature on the thermoelectric properties and hardness of the samples was also discussed in detail. The results showed that the grain size, density, dimension size and mass remained nearly unchanged when the service temperature was below 523 K, which suggested that the geometry size of zone melting p-type (Bi, Sb)2Te3-based materials was stable below 523 K. The power factor and Vickers hardness of the ingots also changed little and maintained good thermal stability. Unfortunately, the thermal conductivity increased with increasing annealing temperature, which resulted in an obvious decrease of the zT value. In addition, the thermal stabilities of the zone melting p-type (Bi, Sb)2Te3-based materials and the corresponding powder metallurgy samples were also compared. All evidence implied that the thermal stabilities of the zone-melted (ZMed) p-type (Bi, Sb)2Te3 ingots in terms of crystal structure, geometry size, power factor (PF) and hardness were better than those of the corresponding powder metallurgy samples. However, their thermal stabilities in terms of zT values were similar under different annealing temperatures.

High quality InAsSb grown on InP substrates using AlSb/AlAsSb buffer layers

International Nuclear Information System (INIS)

Wu, B.-R.; Liao, C.; Cheng, K. Y.

2008-01-01

High quality InAsSb grown on semi-insulating InP substrates by molecular beam epitaxy was achieved using AlSb/AlAsSb structure as the buffer layer. A 1000 A InAsSb layer grown on top of 1 μm AlSb/AlAsSb buffer layer showed a room temperature electron mobility of ∼12 000 cm 2 /V s. High structural quality and low misfit defect density were also demonstrated in the InAsSb layer. This novel AlSb/AlAsSb buffer layer structure with the AlAsSb layer lattice matched to InP substrates could enhance the performance of optoelectronic devices utilizing 6.1 A family of compound semiconductor alloys

Formation Mechanism of Self Assembled Horizontal ErSb Nanowires Embedded in a GaSb(001) Matrix

Science.gov (United States)

Wilson, Nathaniel; Kraemer, Stephan; PalmstrøM, Chris

The ErxGa1-xSb exhibits a variety of self-assembling nanostructures. In order to harness these nanostructures for use in devices and other material systems it is important to understand their formation. We have characterized the growth mechanism of self-assembled horizontal ErSb nanowires in a GaSb(001) matrix through the use of in-situ Scanning Tunneling Microscopy (STM) as well as ex-situ Transmission Electron Microscopy (TEM). We observe large GaSb macrosteps on the growth surface of Er.3Ga.7Sb samples. The areas near the ledge and base of the macrosteps show significant differences in size and distribution of ErSb nanowires. Results suggest that the formation of macrosteps drives the transition from vertical to horizontal nanowires in the ErxGa1-xSb system. We also observe a low temperature growth mode, which results in horizontal nanowire formation under a wide range of flux conditions. This new growth mode does not exhibit the embedded growth observed in the formation of nanowires at higher temperatures and may allow for horizontal nanowire formation without the presence of macrosteps, as well as the formation of smaller nanoparticles which may be useful for achieving smaller nanoparticle dimensions and electron confinement effects. This work was supported by NSF-DMR under 1507875.

TL dating of vases with elephant ears in Yuan Dynasty

International Nuclear Information System (INIS)

Xia Junding; Wang Weida; Leung, P.L.

2005-01-01

Thermoluminescence (TL) dating using an activation method in pre-dose technique was described. Three vases in underglaze blue with elephant ears and one vase in underglaze red with elephant ears in Yuan Dynasty were dated by this method. The results show that the TL ages are all less than 100 a B.P., and in which sbc 648 and sbc 649 were imitated in recent years. This method is quick, convenient and reliable for porcelain dating with the age of less than 1000 a B.P.. As a comparison, a porcelain sample with underglaze blue in Yuan Dynasty was dated too, and its TL age is 620 ± 140 B.P.. In addition, some complex factors associated with dating have been discussed and a resolution has been raised, which will help improve the accuracy of TL dating. (authors)

Development of low background CsI(Tl) and NaI(Tl) crystals for WIMP search

Energy Technology Data Exchange (ETDEWEB)

Lee, Hyun Su [Department of Physics, Ewha Womans University, Seoul 120-750 (Korea, Republic of)

2015-08-17

We have developed low background CsI(Tl) and NaI(Tl) crystals to search for weakly interacting massive particles as well as to verify the origin of the annual modulation signal observed by the DAMA/LIBRA experiment. Extensive studies about the contamination mechanisim of {sup 137}Cs in CsI powder lead to the growth of ultra-low-background CsI(Tl) crystals. Similar approaches for NaI(Tl) crystals have been applied to reduce internal backgrounds to less than 0.5 counts/kg/day/keV. Status and understanding of backgrounds and background reduction in NaI(Tl) crystals will be discussed.

Chemical Bonding in Tl Cuprates Studied by X-Ray Photoemission

Energy Technology Data Exchange (ETDEWEB)

Lao, J.Y.; Overmyer, D.L.; Ren, Z.F.; Siegal, M.P.; Vasquez, R.P.; Wang, J.H.

1999-04-05

Epitaxial thin films of the Tl cuprate superconductors Tl{sub 2}Ba{sub 2}CaCu{sub 2}O{sub 8}, Tl{sub 2}Ba{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}, and TL{sub 0.78}Bi{sub 0.22}Ba{sub 0.4}Sr{sub 1.6}Ca{sub 2}Cu{sub 3}O{sub 9{minus}{delta}} are studied with x-ray photoemission spectroscopy. These data, together with previous measurements in this lab of Tl{sub 2}Ba{sub 2}CuO{sub 6+{delta}} and TlBa{sub 2}CaCu{sub 2}O{sub 7{minus}{delta}}, comprise a comprehensive data set for a comparative study of Tl cuprates with a range of chemical and electronic properties. In the Cu 2p spectra, a larger energy separation between the satellite and main peaks (E{sub s}-E{sub m}) and a lower intensity ratio (I{sub s}/I{sub m}) are found to correlate with higher values of T{sub c}. Analysis of these spectra within a simple configuration interaction model suggests that higher values of T{sub c} are related to low values of the O 2p {r_arrow} Cu 3d charge transfer energy. In the O 1s region, a smaller bond length between Ba and Cu-O planar oxygen is found to correlate with a lower binding energy for the signal associated with Cu-O bonding, most likely resulting from the increased polarization screening by Ba{sup 2+} ions. For samples near optimum doping, maximum T{sub c} is observed to occur when the Tl 4f{sub 7/2} binding energy is near 117.9 eV, which is near the middle of the range of values observed for Tl cuprates. Higher Tl 4f{sub 7/2} binding energies, corresponding to formal oxidation states nearer Tl{sup 1+}, are also found to correlate with longer bond lengths between Ba and Tl-O planar oxygen, and with higher binding energies of the O 1s signal associated with Tl-O bonding.

Chemical bonding in Tl cuprates studied by x-ray photoemission

Energy Technology Data Exchange (ETDEWEB)

Vasquez, R.P. [Center for Space Microelectronics Technology, Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California 91109-8099 (United States); Siegal, M.P.; Overmyer, D.L. [Sandia National Laboratories, Albuquerque, New Mexico 87185-1421 (United States); Ren, Z.F.; Lao, J.Y.; Wang, J.H. [Materials Synthesis Laboratory, Department of Chemistry, State University of New York, Buffalo, New York 14260-3000 (United States)

1999-08-01

Epitaxial thin films of the Tl cuprate superconductors Tl{sub 2}Ba{sub 2}CaCu{sub 2}O{sub 8}, Tl{sub 2}Ba{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}, and Tl{sub 0.78}Bi{sub 0.22}Ba{sub 0.4}Sr{sub 1.6}Ca{sub 2}Cu{sub 3}O{sub 9{minus}{delta}} are studied with x-ray photoemission spectroscopy. These data, together with previous measurements in this lab of Tl{sub 2}Ba{sub 2}CuO{sub 6+{delta}} and TlBa{sub 2}CaCu{sub 2}O{sub 7{minus}{delta}}, comprise a comprehensive data set for a comparative study of Tl cuprates with a range of chemical and electronic properties. In the Cu 2p spectra, a larger energy separation between the satellite and main peaks (E{sub s}{minus}E{sub m}) and a lower intensity ratio (I{sub s}/I{sub m}) are found to correlate with higher values of T{sub c}. Analysis of these spectra within a simple configuration interaction model suggests that higher values of T{sub c} are related to low values of the O&hthinsp;2p{r_arrow}Cu&hthinsp;3d charge transfer energy. In the O&hthinsp;1s region, a smaller bond length between Ba and Cu-O planar oxygen is found to correlate with a lower binding energy for the signal associated with Cu-O bonding, most likely resulting from the increased polarization screening by Ba{sup 2+} ions. For samples near optimum doping, maximum T{sub c} is observed to occur when the Tl 4f{sub 7/2} binding energy is near 117.9 eV, which is near the middle of the range of values observed for Tl cuprates. Higher Tl&hthinsp;4f{sub 7/2} binding energies, corresponding to formal oxidation states nearer Tl{sup 1+}, are also found to correlate with longer bond lengths between Ba and Tl-O planar oxygen, and with higher binding energies of the O&hthinsp;1s signal associated with Tl-O bonding. {copyright} {ital 1999} {ital The American Physical Society}

The formation mechanisms and optical characteristics of GaSb quantum rings

International Nuclear Information System (INIS)

Lin, Wei-Hsun; Pao, Chun-Wei; Wang, Kai-Wei; Liao, Yu-An; Lin, Shih-Yen

2013-01-01

The growth mechanisms and optical characteristics of GaSb quantum rings (QRs) are investigated. Although As-for-Sb exchange is the mechanism responsible for the dot-to-ring transition, significant height difference between GaSb quantum dots (QDs) and QRs in a dot/ring mixture sample suggests that the dot-to-ring transition is not a spontaneous procedure. Instead, it is a rapid transition procedure as long as it initiates. A model is established to explain this phenomenon. Larger ring inner diameters and heights of the sample with longer post Sb soaking time suggest that As-for-Sb exchange takes places in both vertical and lateral directions. The decreasing ring densities, enlarged ring inner/outer diameters and eventually flat GaSb surfaces observed with increasing growth temperatures are resulted from enhanced adatom migration and As-for-Sb exchange with increasing growth temperatures

Observation of curious spiral growth features in Tl doped Hg bearing ...

Indian Academy of Sciences (India)

Synthesis of H(Tl)Ba2Ca2Cu3O8+ superconducting tapes have been accomplished by annealing the precursor tape, Ba2Ca2Cu3O (fabricated by doctor blade tape casting technique) in an environment of H(Tl) vapour. Characterization of superconducting HTSC tape sample was carried out through XRD, TEM, SEM ...

Program for the evaluation of TL-brick dating: 'ADAM-1-EVA'

International Nuclear Information System (INIS)

Novotna, V.; Kubelik, M.; Musilek, L.

2000-01-01

Although the evaluation of the TL-mean date has presented very little diversity since first published, the error evaluation has prompted a lot of discussion. Particularly the physical, chemical, statistical and mathematical differences as reflected in the specifics of the evaluation of the individual random and systematic errors in ceramic and brick dating are undervalued in literature. The construction of an automated TL-Reader (ADAM-1) at the Czech Technical University in Prague was taken as an opportunity to create a whole new software package for the evaluation ('EVA') of TL-dates. ADAM-1 is designed primarily for brick dating, using the fine-grain technique. The philosophy of data processing is similar to that applied by the Berlin group in their research of Venetian Villas. The program was developed using Delphi, as it is user-friendlier than pure Pascal, offers a strong graphic platform and allows flexibility in data management. This was important, as the program was conceived to either interact directly with ADAM-1, or to be operated independently for data evaluation and management. The software package consists of two discrete yet combinable components: one for the calculation of the TL mean date, using all raw data obtained from ADAM-1 and peripheral measurements; the other for the evaluation of systematic, random and context errors of individual samples and sample groups. All steps in the calculations are also graphically available, e.g. glow curves, plateau test, TL vs. dose dependence and charts summarising the results of all calculations for an individual sample and a given context. (author)

Identification of food preserved by ionizing radiation; Preliminary tests in strawberries using thermoluminescent (TL)

International Nuclear Information System (INIS)

Rubio, T.; Sillano, O.; Espinoza, J.; Roman, A.; Deza, A.

1992-01-01

TL measurements, of irradiated and unirradiated strawberries were carried out, using peel, seeds (achenes), leaves and sediment. The four types of samples presented a different thermoluminescence response. The best results were obtained with sediment removed from the soil of the fruit surface. It is concluded that TL is a promising technique for detecting irradiated strawberries using sediment samples. (author)

Magnetic properties of Bi- and Tl- based new high-Tc superconductors

International Nuclear Information System (INIS)

Togano, K.; Kumakura, H.; Dietderich, D.H.

1988-01-01

Upper critical field H c2 and Magnetization curve were measured for new high-T c oxide superconductors of Bi-Sr-Ca-Cu-O and Tl-Ba-Ca-Cu-O systems. H c2 values at 77K for the high-T phase of Bi-Sr-Ca-Cu-O, low-T c (T c (ρ = 0) = 105K) phase of Tl-Ba-Ca-Cu-O, and high-T c (T c (ρ = 0)=115K) phase of Tl-Ba-Ca-Cu-O are 41T, 50T, and 100T, respectively. The magnetization curve of the Bi-Sr-Ca-Cu-O shows a relatively small hysterisis, suggesting a weak pinning force compared to Tl-Ba-Ca-Cu-O as well as Ba 2 YCU 3 O x . Critical current density J c of 600A/Cm 2 at 77K and zero-magnetiac field was attained for the high-T c sample of Tl-Ba-Ca-Cu-O

TANK 40 FINAL SB4 CHEMICAL CHARACTERIZATION RESULTS

International Nuclear Information System (INIS)

Best, J.

2008-01-01

A sample of Sludge Batch 4 (SB4) was pulled from Tank 40 in order to obtain radionuclide inventory analyses necessary for compliance with the Waste Acceptance Product Specifications (WAPS). This sample was also analyzed for elemental and chemical composition including noble metals. These analyses along with the WAPS analyses will help define the composition of the sludge currently in Tank 40 which is currently being fed to DWPF and will become part of Sludge Batch 5 (SB5). At SRNL the 3-L Tank 40 SB4 sample was transferred from the shipping container into a 4-L vessel and solids allowed to settle overnight. Supernate was then siphoned off and circulated through the shipping container to complete the transfer of the sample. Following thorough mixing of the 3-L sample, a 280 g sub-sample was removed. This sub-sample was then utilized for all subsequent analytical samples. Eight separate aliquots of the slurry were digested, four with HNO 3 /HCl in sealed Teflon(reg s ign) vessels and four in Na 2 O 2 using Zr crucibles. Due to the use of Zr crucibles and Na in the peroxide fusions, Na and Zr cannot be determined from this preparation. Three glass standards were digested along with a blank for each preparation. Each aqua regia digestion and blank was diluted and submitted to Analytical Development (AD) for inductively coupled plasma-atomic emission spectroscopy (ICP-AES) analysis, inductively coupled plasma-mass spectrometry (ICP-MS) analysis, and cold vapor atomic absorption (CV-AA) analysis. Equivalent dilutions of the peroxide fusion digestions and blank were submitted to AD for ICP-AES analysis. Tank 40 SB4 supernate was collected from a mixed slurry sample in the SRNL Shielded Cells and submitted to AD for ICP-AES and ICP-MS. Weighted dilutions of slurry were submitted for ion chromatography (IC), total inorganic carbon/total organic carbon (TIC/TOC), and total base analyses. A sample of Tank 40 SB4 decant was collected by carefully removing the supernate phase

Electronic structure of TlBa2CaCu2O7-δ

Science.gov (United States)

Vasquez, R. P.; Novikov, D. L.; Freeman, A. J.; Siegal, M. P.

1997-06-01

The core levels of TlBa2CaCu2O7-δ (Tl-1212) epitaxial films have been measured with x-ray photoelectron spectroscopy (XPS). The valence electronic structure has been determined using the full-potential linear muffin-tin-orbital band-structure method and measured with XPS. The calculations show that a van Hove singularity (VHS) lies above the Fermi level (EF) for the stoichiometric compound (δ=0), while for 50% oxygen vacancies in the Tl-O layer (δ=0.5) EF is in close proximity to the VHS. Samples annealed in nitrogen (to reduce the hole overdoping by the removal of oxygen) exhibit higher core-level binding energies and a higher Tc, consistent with a shift of EF closer to the VHS. Comparisons are made to the core levels and valence bands of Tl2Ba2CaCu2O8+δ (Tl-2212) and HgBa2CaCu2O6+δ (Hg-1212). The similarity of the Cu 2p3/2 spectra for Tl-1212 and Tl-2212 indicates that the number of Tl-O layers has little effect on the Cu-O bonding. However, the Tl-1212 and Hg-1212 Cu 2p3/2 signals exhibit differences which suggest that the replacement of Tl3+ with Hg2+ results in a decrease in the O 2p-->Cu 3d charge-transfer energy and differences in the probabilities of planar vs apical oxygen charge transfer and/or Zhang-Rice singlet-state formation. Differences between the Tl-1212 and the Tl-2212 and Hg-1212 measured valence bands are consistent with the calculated Cu 3d and (Tl,Hg) 6s/5d partial densities of states.

Electronic structure of TlBa2CaCu2O7-δ

International Nuclear Information System (INIS)

Vasquez, R.P.; Novikov, D.L.; Freeman, A.J.; Siegal, M.P.

1997-01-01

The core levels of TlBa 2 CaCu 2 O 7-δ (Tl-1212) epitaxial films have been measured with x-ray photoelectron spectroscopy (XPS). The valence electronic structure has been determined using the full-potential linear muffin-tin-orbital band-structure method and measured with XPS. The calculations show that a van Hove singularity (VHS) lies above the Fermi level (E F ) for the stoichiometric compound (δ=0), while for 50% oxygen vacancies in the Tl-O layer (δ=0.5) E F is in close proximity to the VHS. Samples annealed in nitrogen (to reduce the hole overdoping by the removal of oxygen) exhibit higher core-level binding energies and a higher T c , consistent with a shift of E F closer to the VHS. Comparisons are made to the core levels and valence bands of Tl 2 Ba 2 CaCu 2 O 8+δ (Tl-2212) and HgBa 2 CaCu 2 O 6+δ (Hg-1212). The similarity of the Cu 2p 3/2 spectra for Tl-1212 and Tl-2212 indicates that the number of Tl-O layers has little effect on the Cu-O bonding. However, the Tl-1212 and Hg-1212 Cu 2p 3/2 signals exhibit differences which suggest that the replacement of Tl 3+ with Hg 2+ results in a decrease in the O 2p→Cu 3d charge-transfer energy and differences in the probabilities of planar vs apical oxygen charge transfer and/or Zhang-Rice singlet-state formation. Differences between the Tl-1212 and the Tl-2212 and Hg-1212 measured valence bands are consistent with the calculated Cu 3d and (Tl,Hg) 6s/5d partial densities of states. copyright 1997 The American Physical Society

Quality control 201TlCl solution obtained at IPEN-CNEN/SP through the direct method of 201Tl preparation

International Nuclear Information System (INIS)

Fernandes, L.; Silva, C.P.G. da.

1991-09-01

The radiopharmaceutical 201 TlCl is used in Nuclear medicine for myocardial visualization. The solution of 201 TlCl was prepared using 201 Tl obtained by irradiating a natural mercury target with protons. This radionuclide was subjected to different quality control processes to verify the purity required for its use in Medicine. Some of these controls concerned the determination of 200 Tl, 201 Tl and 202 Tl; the chemical identification of 201 Tl +1 ; the hydrazine concentration, mercury contamination and the presence of phosphate. Furthermore, the biologic distribution in Wistar rats and tests for sterility, pyrogens and for toxicity were carried out. It was verified that the solution obtained was in the form of thallous chloride. This radiopharmaceutical can give a good heart image in animals but due to the contamination of 201 Tl with 200 Tl and 202 Tl its use in human beings is not possible unless enriched 202 Hg is used as target of irradiation. (author)

Growth of GaSb1-xBix by molecular beam epitaxy

DEFF Research Database (Denmark)

Song, Yuxin; Wang, Shumin; Roy, Ivy Saha

2012-01-01

Molecular beam epitaxy for GaSb1-xBix is investigated in this article. The growth window for incorporation of Bi in GaSb was found. Strategies of avoiding formation of Bi droplets and enhancing Bi incorporation were studied. The Bi incorporation was confirmed by SIMS and RBS measurements. The Bi ......As substrates were compared and no apparent difference for Bi incorporation was found.......Molecular beam epitaxy for GaSb1-xBix is investigated in this article. The growth window for incorporation of Bi in GaSb was found. Strategies of avoiding formation of Bi droplets and enhancing Bi incorporation were studied. The Bi incorporation was confirmed by SIMS and RBS measurements. The Bi...... concentration in the samples was found to increase with increasing growth temperature and Bi flux. The position of GaSb1-xBix layer peak in XRD rocking curves is found to be correlated to Bi composition. Surface and structural properties of the samples were also investigated. Samples grown on GaSb and Ga...

Electronic Structure of TlBa2CaCu2O(7-Delta)

Science.gov (United States)

Vasquez, R. P.; Novikov, D. L.; Freeman, A. J.; Siegal, M. P.

1997-01-01

The core levels of TlBa2CaCu2O(7-delta) (Tl-1212) epitaxial films have been measured with X-ray photoelectron spectroscopy (XPS). The valence electronic structure has been determined using the full-potential linear muffin-tin-orbital band-structure method and measured with XPS. The calculations show that a van Hove singularity (VHS) lies above the Fermi level (E(sub F)) for the stoichiometric compound (delta = 0.5), while for 50% oxygen vacancies in the Tl-O layer (delta = 0.5) E(sub F) is in close proximity to the VHS. Samples annealed in nitrogen (to reduce the hole overdoping by the removal of oxygen) exhibit higher core-level binding energies and a higher T(sub c), consistent with a shift of E(sub F) closer to the VHS. Comparisons are made to the core levels and valence bands of Tl2Ba2CaCu2O(8 + delta)(Tl-2212) and HgBa2CaCu2O)6 + delta) (Hg- 1212). The similarity of the Cu 2p(sub 3/2) spectra for Tl-1212 and Tl-2212 indicates that the number of Tl-O layers has little effect on the Cu-O bonding. However, the Tl-1212 and Hg-1212 Cu 2p(sub 3/2) signals exhibit differences which suggest that the replacement of T(sup 3+) with Hg(sup 2+) results in a decrease in the O 2p right arrow Cu 3d charge-transfer energy and differences in the probabilities of planar vs apical oxygen charge transfer and/or Zhang-Rice singlet-state formation. Differences between the Tl-1212 and the Tl-2212 and Hg-1212 measured valence bands are consistent with the calculated Cu 3d and (Tl,Hg) 6s/5d partial densities of states.

Growth and characterization of an InSb infrared photoconductor on Si via an AlSb/GaSb buffer

Science.gov (United States)

Jia, Bo Wen; Tan, Kian Hua; Loke, Wan Khai; Wicaksono, Satrio; Yoon, Soon Fatt

2018-05-01

A 99.6% relaxed InSb layer is grown on a 6° offcut (1 0 0) Si substrate via an AlSb/GaSb buffer using molecular beam epitaxy (MBE). A 200 nm GaSb buffer is first grown on Si and the lattice mismatch between them is accommodated by an interfacial misfit (IMF) array consisting of uniformly distributed 90° misfit dislocations. Si delta doping is introduced during the growth of GaSb to reduce the density of threading dislocation. Subsequently, a 50 nm AlSb buffer is grown followed by a 0.8 μm InSb layer. The InSb layer exhibits a 300 K electron mobility of 22,300 cm2/Vs. An InSb photoconductor on Si is demonstrated with a photoconductive gain from 77 K to 200 K under a 700 °C maintained blackbody.

Effect of laser irradiation on Ag4In12Sb56Te28

Science.gov (United States)

Chinnusamy, Rangasami

2018-04-01

Ag4In12Sb56Te28 has been synthesized by melt-quench method. Phase homogeneity, crystal structure and effect of laser irradiation have been investigated using X-ray diffraction (XRD) and Raman spectroscopy. Rietveld refinement of crystal structure revealed that Ag4In12Sb56Te28 is a multiphase system with AgIn3Te5, Sb8Te3 and Sb phases. Combined optical microscopy and Raman spectroscopy have been used to understand the distribution of different phases on the surface of the samples, which substantiated the results of Rietveld analysis. Interaction of 20 mW laser beam with samples has been investigated using Raman measurements. The results have shown that regions with large phase fraction of AgIn3Te5 become amorphous during laser-sample interaction, but the starting phase remains nearly same after the interaction. Regions with AgIn3Te5 and nearly equal or larger amount of Sb8Te3 have shown significant growth of α-Sb2O3 during and after laser-sample interaction. Regions rich in Sb have shown formation of AgIn3Te5 and growth of α-Sb2O3 during and after interaction. These observations have been explained based on the maximum temperature rise at different regions during laser-sample interaction.

TL sensitivity constancy of quartz upon UV+(β,γ) irradiation cycle: An improvement on dating methodology

International Nuclear Information System (INIS)

Souza, J.H.

1985-01-01

Thermoluminescence (TL) sensivitivy of natural quartz (beaches, paleobeaches and fixed dunes) to Beta and Gamma rays has been studied in a temperature range between 250-400 0 C, before and after bleaching by solar irradiation. A first TL glow growth curve was obtained through Beta irradiation of 'as found' samples and a second glow growth curve was obtained by bleaching through solar irradiation the TL acquired either through an excitation Gamma dose or through environmental radiation to finally re-irradiate the samples under Beta rays. Experimental results showing the constancy of sensitivity, for doses of until about 10K rads, are the basis for a proposal to improve TL dating methodology expanding its present limits. (Author) [pt

TL/OSL properties of natural schist for archaeological dating and retrospective dosimetry

International Nuclear Information System (INIS)

Afouxenidis, D.; Stefanaki, E.C.; Polymeris, G.S.; Sakalis, A.; Tsirliganis, N.C.; Kitis, G.

2007-01-01

Schist, a metamorphic rock composed largely of quartz and muscovite, has been used as a building stone through the centuries in many parts of the world. In ancient Greece, it was used in buildings and monuments (Knossos, Karthaia, etc). Basic TL and OSL properties of schist are studied in the present work to evaluate its potential use in archaeological dating and retrospective dosimetry. In particular, the optical stability, as well as the linearity of the TL and OSL signal were investigated for samples of natural schist obtained from a roofing slate. The results indicate that both signals are rapidly bleached when the sample is exposed to sunlight. An exposure of 1 min reduces the TL signal by 93%, the IRSL signal by 99% and the post-IR BSL signal by 90%. The dose response was found to be linear for a radiation dose at least up to 75 Gy for the TL and the IR OSL signal and at least up to 25 Gy for the post-IR BSL signal

DWPF SB6 Initial CPC Flowsheet Testing SB6-1 TO SB6-4L Tests Of SB6-A And SB6-B Simulants

International Nuclear Information System (INIS)

Lambert, D.; Pickenheim, B.; Best, D.

2009-01-01

The Defense Waste Processing Facility (DWPF) will transition from Sludge Batch 5 (SB5) processing to Sludge Batch 6 (SB6) processing in late fiscal year 2010. Tests were conducted using non-radioactive simulants of the expected SB6 composition to determine the impact of varying the acid stoichiometry during the Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) processes. The work was conducted to meet the Technical Task Request (TTR) HLW/DWPF/TTR-2008-0043, Rev.0 and followed the guidelines of a Task Technical and Quality Assurance Plan (TT and QAP). The flowsheet studies are performed to evaluate the potential chemical processing issues, hydrogen generation rates, and process slurry rheological properties as a function of acid stoichiometry. These studies were conducted with the estimated SB6 composition at the time of the study. This composition assumed a blend of 101,085 kg of Tank 4 insoluble solids and 179,000 kg of Tank 12 insoluble solids. The current plans are to subject Tank 12 sludge to aluminum dissolution. Liquid Waste Operations assumed that 75% of the aluminum would be dissolved during this process. After dissolution and blending of Tank 4 sludge slurry, plans included washing the contents of Tank 51 to ∼1M Na. After the completion of washing, the plan assumes that 40 inches on Tank 40 slurry would remain for blending with the qualified SB6 material. There are several parameters that are noteworthy concerning SB6 sludge: (1) This is the second batch DWPF will be processing that contains sludge that has had a significant fraction of aluminum removed through aluminum dissolution; (2) The sludge is high in mercury, but the projected concentration is lower than SB5; (3) The sludge is high in noble metals, but the projected concentrations are lower than SB5; and(4) The sludge is high in U and Pu - components that are not added in sludge simulants. Six DWPF process simulations were completed in 4-L laboratory-scale equipment using

Si(Li)-NaI(Tl) sandwich detector array for measurements of trace radionuclides in soil samples

International Nuclear Information System (INIS)

Strauss, M.G.; Sherman, I.S.; Roche, C.T.; Pehl, R.H.

1986-01-01

An ultra-sensitive X/γ-ray detector system for assaying trace radioactivity in actinide contaminated soil and ash samples has been developed. The new system consists of an array of 6 large Si(Li) X-ray detectors sensitive on both faces and mounted on edge in a paddle-shaped cryostat with a 14 cm diameter Be window on each side. The paddle, with a sample of the soil placed at each window, is sandwiched between 2 large NaI(Tl) scintillators which suppress the γ background. With X-rays being measured simultaneously from soil in 2 sample holders and background reduced by 50% using anticoincidence, the sensitivity of this detector is 4 times higher than that of conventionally mounted Si(Li) detectors. A soil sample containing 50 pCi/g 239 Pu was measured in 5 min with an uncertainty of 1 and NpLsub(β1) X-ray peaks are resolved thus permitting measurement of trace Pu in the presence of 241 Am. This is the most sensitive and selective detector known for nondestructive assay of radioactivity in soil and other samples. (orig.)

Optical and electrical properties of Te doped AlGaAsSb/AlAsSb Bragg mirrors on InP

OpenAIRE

Toginho Filho, D. O.; Dias, I. F. L.; Duarte, J. L.; Laureto, E.

2006-01-01

We present a comparative study carried out on the optical and electrical characteristics of undoped and Te doped AlGaAsSb/AlAsSb Bragg mirrors with 6.5 pairs of layers and bulk undoped and Te doped AlGaAsSb epilayers alloys lattice matched on InP, grown by molecular beam epitaxy, using SIMS, photoluminescence, reflectivity and IxV techniques. The temperature dependence of PL transitions observed in the Bragg mirrors are similar to that observed in bulk samples and associated with the donor an...

Nuclear resonance fluorescence of {sup 203,205}Tl

Energy Technology Data Exchange (ETDEWEB)

Pfeifer, Fabian; Fritzsche, Matthias; Pietralla, Norbert; Savran, Deniz; Weller, Henry; Zweidinger, Markus [Institut fuer Kernphysik, Technische Universitaet, Darmstadt (Germany); Rusev, Gencho; Tonchev, Anton P.; Tornow, Werner [Triangle Universities Nuclear Laboratory, Duke University, Durham (United States); Zilges, Andreas [Institut fuer Kernphysik, Universitaet Koeln (Germany)

2009-07-01

In order to investigate the dipole strength distribution in Thalium isotopes we have studied Nuclear Resonance Fluorescence of a sample composed of natural Thallium (consisting of 30% {sup 203}Tl and 70% {sup 205}Tl). Unpolarized bremsstrahlung with photo energies up to 7.5 MeV was used at the High Intensity Photon Setup (HIPS) at S-DALINAC at the IKP Darmstadt. 24 fluorescent {gamma}-ray transitions were observed, 19 of them for the first time. For the assignment of the polarity of two prominent {gamma}-ray transitions, one at 4.7 MeV and one at 4.9 MeV, the polarized photon beam of the High Intensity {gamma}-ray Source (HI{gamma}S) at Duke University was used. The experiment at HI{gamma}S revealed the existence of a photo-excited state of {sup 205}Tl at an excitation energy of 4.971 MeV that exhibits a transition to the first excited state at 203 keV.

Preliminary results on TL and OSL aluminium oxide dosimeters developed at IPEN

Energy Technology Data Exchange (ETDEWEB)

Fukumori, David T.; Yoshito, Walter K.; Ussui, Valter; Lazar, Dolores R.R.; Campos, Leticia L., E-mail: fukumori@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

The aluminum oxide composes the modern TL and OSL radiation dosimeters. TL and OSL phenomena are related to chemical elements in the crystalline structure of {alpha}-Al{sub 2}O{sub 3}. The aim of this work was to develop materials based on aluminum oxide for use in TL and OSL dosimetry. The studies included the dosimetric properties of alumina samples obtained by electro fusion, adsorption and coprecipitation. Electro fused alumina commercially available as abrasive particles was used to produce the pellets by glass sintering. Adsorption and coprecipitation were the methods used to insert metal ions to alumina. The best results were achieved with electro fused alumina and Tm{sup 3+} doped Al{sub 2}O{sub 3} pellets. The electro fused alumina-glass pellets show TL and OSL signals and the TL curve has two peaks. Its minimum detectable radiation dose is 7.2 mGy and the linearity of TL response as function of dose is up to about 800 mGy. The {alpha}-Al{sub 2}O{sub 3}:Tm pellets produced by sintering at 1550 deg C presented a meaningful TL glow curve so that it is worth studying their properties and viability of use in dosimetry. (author)

Structural instability and photoacoustic study of AlSb prepared by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Triches, D.M.; Souza, S.M.; Poffo, C.M. [Departamento de Engenharia Mecanica, Universidade Federal de Santa Catarina, 88040-900 Florianopolis, SC (Brazil); Lima, J.C. de, E-mail: fsc1jcd@fsc.ufsc.b [Departamento de Fisica, Universidade Federal de Santa Catarina, 88040-900 Florianopolis, SC (Brazil); Grandi, T.A. [Departamento de Fisica, Universidade Federal de Santa Catarina, 88040-900 Florianopolis, SC (Brazil); Biasi, R.S. de [Secao de Engenharia Mecanica e de Materiais, Instituto Militar de Engenharia, 22290-270 Rio de Janeiro, RJ (Brazil)

2010-09-03

High-purity elemental Al and Sb powders were blended with equiatomic composition and submitted to mechanical alloying. For all milling times, the milled powders showed a mixture of AlSb and elemental Sb. The largest amount of AlSb was reached for milling times between 7 and 10 h. For milling times larger than 10 h, decomposition of AlSb was observed. The volume fractions of the crystalline and interfacial components were estimated using the X-ray diffraction pattern of a sample milled for 10 h. Photoacoustic absorption spectroscopy (PAS) was used to determine the thermal diffusivity and other heat transport parameters in the same sample. A combination of XRD and PAS data was used to estimate the thermal diffusivity of the interfacial component, which has a significant contribution to the thermal diffusivity of the sample.

Structural instability and photoacoustic study of AlSb prepared by mechanical alloying

International Nuclear Information System (INIS)

Triches, D.M.; Souza, S.M.; Poffo, C.M.; Lima, J.C. de; Grandi, T.A.; Biasi, R.S. de

2010-01-01

High-purity elemental Al and Sb powders were blended with equiatomic composition and submitted to mechanical alloying. For all milling times, the milled powders showed a mixture of AlSb and elemental Sb. The largest amount of AlSb was reached for milling times between 7 and 10 h. For milling times larger than 10 h, decomposition of AlSb was observed. The volume fractions of the crystalline and interfacial components were estimated using the X-ray diffraction pattern of a sample milled for 10 h. Photoacoustic absorption spectroscopy (PAS) was used to determine the thermal diffusivity and other heat transport parameters in the same sample. A combination of XRD and PAS data was used to estimate the thermal diffusivity of the interfacial component, which has a significant contribution to the thermal diffusivity of the sample.

Thallium (Tl) sorption onto illite and smectite: Implications for Tl mobility in the environment

Science.gov (United States)

Martin, Loïc A.; Wissocq, Aubéry; Benedetti, M. F.; Latrille, Christelle

2018-06-01

Clay minerals play a relevant role in the transport and fate of trace elements in the environment. Though illite has been referred as an important Thallium (Tl) bearing phase in soils, mechanisms and affinity of thallium for clay minerals remain poorly known. This study investigated the sorption behavior of thallium as Tl(I) onto illite and smectite, two clay minerals occurring mainly in soils and sediments. Different sorption experiments were carried out under various pH conditions and Tl concentrations, in competition with sodium and calcium at a constant ionic strength of 0.01 mol L-1. Our results showed that illite displayed more affinity than smectite for thallium. With illite, the distribution coefficients (Kd in L kg-1) varied between 102.75 ± 0.17 and 104.0 ± 0.17 in Na solutions versus between 102.25 ± 0.17 and 103.0 ± 0.17 in Ca solutions, depending on pH. With smectite, Kd (in L kg-1) ranged between 102.50 ± 0.16 and 103.20 ± 0.16 and between 101.25 ± 0.16 and 101.95 ± 0.16 in Na and Ca solutions, respectively. Sorption behavior was described with the Multi-Site Ion Exchanger model and selectivity coefficients with respect to protons were calculated for the first time. In all cases, independently of clay mineral and background electrolyte, low capacity but highly reactive sites were dominant in thallium uptake, highlighting Tl affinity for those sites. Moreover, the exchangeable and reversible interactions between Tl+ and clays reactive sites suggested that in changing conditions, thallium could be released in solution. The role of clay minerals in thallium environmental cycle is evident and confirmed illite to be a dominant Tl bearing phase, in some environment competing with manganese oxides. Compared to others Tl bearing mineral phases, clays are ranked as follows: MnO2 > illite > smectite ∼ ferrihydrite ≥ Al2O3 ∼ goethite > SiO2. Finally, over the three monovalent cations (Tl, Rb, Cs) Tl is the one less sorbed on illite independently of

X-ray diffraction, Raman and photoacoustic studies of InSb nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Ersching, K., E-mail: kleb85@hotmail.com [Departamento de Fisica, Universidade Federal de Santa Catarina, Campus Universitario Trindade, 88040-900 Florianopolis, Santa Catarina (Brazil); Campos, C.E.M.; Lima, J.C. de; Grandi, T.A. [Departamento de Fisica, Universidade Federal de Santa Catarina, Campus Universitario Trindade, 88040-900 Florianopolis, Santa Catarina (Brazil); Souza, S.M. [Departamento de Engenharia Mecanica, Universidade Federal de Santa Catarina, Campus Universitario Trindade, 88040-900 Florianopolis, Santa Catarina (Brazil); Pizani, P.S. [Departamento de Fisica, Universidade Federal de Sao Carlos, 13 565-905 Sao Carlos, SP (Brazil)

2010-08-01

Zinc blend InSb nanocrystals were generated by mechanical alloying and X-ray diffraction, Raman spectroscopy and photoacoustic absorption spectroscopy techniques were used to study its structural, optical and thermal properties. Annealed nanocrystals were also studied. Residual amorphous and minority crystalline (Sb and In{sub 2}O{sub 3}) phases were also observed for mechanical alloyed and thermal annealed samples, respectively. The structural parameters, phase fractions, average crystallite sizes and microstrains of all crystalline phases found in the samples were obtained from Rietveld analyses of their X-ray diffraction patterns. Raman results for both as-milled and annealed samples show the Raman active LO and TO modes of the zinc blend InSb phase and Sb-rich regions. The photoacoustic results of both samples were satisfactorily explained by thermal bending heat transfer mechanism and an increase on effective thermal diffusivity coefficient was observed after annealing.

Quality control of the solution sup(201)TlCl obtained at IPEN-CNEN/SP by sup(201)Tl direct preparation

International Nuclear Information System (INIS)

Fernandes, L.; Silva, C.P.G. da

1991-01-01

The radiopharmaceutical sup(201) TlCl is used in Nuclear Medicine for myocardial visualization. The solution of sup(201)TlCl was prepared using sup(201)Tl obtained by irradiating a natural mercury target with protons. This radionuclide was subjected to different quality control processes to verify the purity required for its use in Medicine. Some of these controls concerned the determination of sup(200)Tl, sup(201)Tl and sup(202)Tl; the chemical identification of sup(201)Tl sup(+1); the hydrazine concentration, mercury contamination and the presence of phosphate. Furthermore, the biologic distribution in Wistar rats and tests for sterility pyrogens and for toxicity were carried out. It was verified that the solution obtained was in the form of tallous chloride. This radiopharmaceutical can give a good heart image in animals but due to the contamination of sup(201)Tl with sup(200)Tl and sup(202)Tl its use in human beings is not possible unless enriched sup(202)Hg is used as target of irradiation. (author)

TL dosimetric properties BAM:EU

International Nuclear Information System (INIS)

Rao, Bellam N.; Murthy, K.V.R.; Subba Rao, B.; Saiprasad, A.S.

2011-01-01

In phosphor area today top priority is the replacement of the high performance but very expensive rare earth activated phosphors with cheaper materials. This essentially means replacing the rare earth ions with transition metal ions or post transition ions. Now a day's phosphors are used in various fields. After World War II, the advances in the optical spectroscopy of solids, especially those of transition metals ions help to evolve research on phosphor and solid state luminescence. In 1960 efficient rare earth activated phosphors were developed for use in color TV (Tb 3+ green, Eu 3+ red, and Dy 3+ yellow). In 1970 tricolor lamp was introduced blue emission from Ce 3+ + Tb 3+ pair was used in tricolor lamps. At present combination of halo phosphor and tri-band phosphor blend is used in many lamp as a compromise between performance, phosphor cost and the lamp making Cost. Thermo luminescence of 0.5 Gy X-ray irradiated BAM.Eu has been studied. The irradiated phosphor has been studied for its TL dosimetric properties one week after irradiation and after 100 weeks of storage. Interesting TL results are reported in the present paper. Heating rate used in the present experiment is 6.6 deg C/Sec. The following two figures are on TL recorded 100 weeks after irradiation and TL recorded after 235 weeks of storage. Before storage for 100 weeks the TL glow curve with a hump around 180 deg C followed by a peak at 273 deg C. After storage for 100 weeks the TL pattern changes entirely. i.e. the composite TL peak structure emerged as two well resolved peaks and with slightly higher TL peak temperatures at 215 deg C and 300 deg C. Normally after storage for 100 weeks the peak at 190 deg C reduces in its intensity or disappears in some cases, instead of that the peak appears at 215 deg C as well resolved peak and its intensity is almost comparable to that of 300 deg C peak. Since the TL phenomenon observed is interesting the two well resolved, isolated, high intensity peaks

Prolate yrast cascade in 183Tl

International Nuclear Information System (INIS)

Reviol, W.; Carpenter, M. P.; Janssens, R. V. F.; Jenkins, D.; Toth, K. S.; Bingham, C. R.; Riedinger, L. L.; Weintraub, W.; Cizewski, J. A.; Lauritsen, T.

2000-01-01

The yrast sequence in 183 Tl has been studied for the first time in recoil-mass selected γ-ray spectroscopic measurements. A rotational-like cascade of seven transitions is established down to the band head with probable spin and parity (13/2 + ). Unlike in the adjacent odd-mass Tl nuclei, prompt γ decay from the yrast band to a lower lying weakly deformed (oblate) structure is not observed. These features are consistent with the predicted drop of the prolate band head in 183 Tl compared to 185 Tl. The implications for the prolate energy minimum in odd-mass Tl nuclei at the neutron i 13/2 midshell (N=103) are discussed. (c) 2000 The American Physical Society

Dissimilatory Sb(V) reduction by microorganisms isolated from Sb-contaminated sediment

Science.gov (United States)

Dovick, M. A.; Kulp, T. R.

2013-12-01

Mining and smelting are major sources of trace metal contamination in freshwater systems. Arsenic (As) is a common contaminant derived from certain mining operations and is a known toxic metalloid and carcinogen. Antimony (Sb) is listed as a pollutant of priority interest by the EPA and is presumed to share similar geochemical and toxicological properties with arsenic. Both elements can occur in four different oxidation states (V, III, 0, and -III) under naturally occurring conditions. In aqueous solutions As(V) and Sb(V) predominate in oxygenated surface waters whereas As(III) and Sb(III) are stable in anoxic settings. Numerous studies have examined microbiological redox pathways that utilize As(V) as a terminal electron acceptor for anaerobic respiration, however there have been few studies on microbial mechanisms that may affect the biogeochemical cycling of Sb in the environment. Here we report bacterial reduction of Sb(V) to Sb(III) in anoxic enrichment cultures and bacterial isolates grown from sediment collected from an Sb contaminated pond at a mine tailings site in Idaho (total pond water Sb concentration = 235.2 +/- 136.3 ug/L). Anaerobic sediment microcosms (40 mL) were established in artificial freshwater mineral salt medium, amended with millimolar concentrations of Sb(V), acetate or lactate, and incubated at 27°C for several days. Antimony(V), lactate, and acetate concentrations were monitored during incubation by High Performance Liquid Chromatography (HPLC) and Ion Chromatography (IC). Live sediment microcosms reduced millimolar amendments of Sb(V) to Sb(III) coupled to the oxidation of acetate and lactate, while no activity occurred in killed controls. Enrichment cultures were established by serially diluting Sb(V)-reducing microcosms in mineral salt medium with Sb(V) and acetate, and a Sb(V)-reducing bacterial strain was isolated by plating on anaerobic agar plates amended with millimolar Sb(V) and acetate. Direct cell counting demonstrated that

Detection Characteristics of Gamma-Irradiated Seeds by using PSL, TL, ESR and GC/MS

International Nuclear Information System (INIS)

Kim, K.H.; Shon, J.H.; Kang, Y.J.; Jo, T.Y.; Park, H.Y.; Kwak, J.Y.; Lee, J.H.; Park, Y.C.; Kim, J.I.; Lee, H.J.; Lee, S.J.; Han, S.B.

2013-01-01

In this study, we investigated the applicability of the photostimulated luminescence (PSL), thermoluminescence (TL), electron spin resonance (ESR) and gas chromatography/mass spectrometry (GC/MS) methods for 5 seeds which are not allowed to be irradiated in Korea. All 5 seeds including evening primrose seed, safflower seed, rape seed, sunflower seed and flax seed were analyzed. Samples were irradiated at 1~10 kGy using a 60 Co gamma-ray irradiator. In PSL study, the photon counts of all the unirradiated samples showed negative (lower than 700). The photon counts of irradiated (1, 5, 10 kGy) samples showed positive (higher than 5,000). In TL analysis, results showed that it is possible to apply TL method to all foods containing minerals. In ESR measurements, the ESR signal (single-line) intensity of irradiated foods was higher than non-irradiated foods. The hydrocarbons 1,7-hexadecadiene (C 16:2 ) and 8-heptadecene (C 17:1 ) from oleic acid were detected only in the irradiated samples before and after the treatment at doses ≥ 1 kGy, but they were not detected in non-irradiated samples before and after treatment. These two hydrocarbons could be used as markers to identify irradiated safflower seed, rape seed, Sunflower seed and flax seed. And then, the hydrocarbons 1,7,10-hexadecatriene (C 16:3 ) and 6,9-heptadecadiene (C 17:2 ) from linoleic acid were detected in the evening primrose seed, safflower seed and sunflower seed. According to the results, PSL, TL and GC/ MS methods were successfully applied to detect the irradiated foods. It is concluded that PSL, TL and GC/MS methods are suitable for detection of irradiated samples and a combined method is recommendable for enhancing the reliability of detection results. (author)

Sb{sup III} - Sb{sup V} Exchange Reaction in Hydrochloric: Acid Solutions; Echange Sb{sup III}-Sb{sup V} dans des Solutions d'Acide Chlorhydrique; Reaktsiya obmena Sb(III) - Sb(V) v rastvorakh khloristovodorodnoj kisloty; Intercambio Sb{sup III}-Sb{sup V} en Soluciones de HCl

Energy Technology Data Exchange (ETDEWEB)

Kambara, T.; Yamaguchi, K.; Yasuba, S. [Shizuoka University, Shizuoka City (Japan)

1965-10-15

The exchange reaction of Sb{sup III} - Sb{sup V} in solutions of low HCl concentrations was studied using {sup 124}Sb as a tracer. The effects of HCl concentrations and chemical forms of antimony on the exchange rate were investigated. The HCl concentrations of the antimony solutions ((Sb{sup III}) =(Sb{sup V}) = 6.8 x 10{sup -4}M) were changed from 0.8 to 4.0M and the half-time for the exchange was measured by plotting log (1 - F) versus time t to calculate the exchange rate assuming the second-ordet reaction. It was found that the exchange rate was sharply increased with the increase of HCl concentrations (at 25 Degree-Sign C, from 0.8 to 2.0M) and at 2.0M HCl concentration the rate reached the maximum, from which the rate was decreased with the increase of HCl concentrations (at 25 Degree-Sign C, from 2.0 to 4.0M). Two sorts of Sb{sup V} species were used for our investigations, i.e. one was used directly after the dilution of 10M HCl Sb{sup V} solution with water and the other was used after 24 hours standing at room temperature from the dilution. (The Sb{sup III} species were also kept standing after preparation from 10M HCl Sb{sup III} solution.) In both cases the maximum rates were found to exist at 2.0M HCl concentration. The rate R{sub 1} for the former (directly after dilution) was 4.5 x 10{sup -6} mole litre{sup -1} min{sup -1} and the rate R{sub 2} for the latter (24 hours standing) was 1.2 x 10{sup -}{sub 6} mole litre. Also the activation energy for these cases was found to be 12.2 kcal/mole and 19.1 kcal/mole. By spectrophotometric studies, the Sb{sup V} species of the former type were found to be mainly consisting of SbCl{sup -}{sub 6} and the species of the latter type to be of SbCl{sub 4}(OH){sup -}{sub 2}, etc. Besides these facts the form of Sb{sup III} species was found to have no influence on the exchange rate. A much sharper increase of the exchange rate was observed when the HCl concentration of the antimony solution was fixed at 0.8M and

Photoconductivity and photomagnetic electromotive force in InSb thin samples

International Nuclear Information System (INIS)

Mosanov, O.; Chonanova, O.G.; Annamamedov, A.G.; Padalko, A.G.; Redzhepov, M.

1987-01-01

Photoconductivity and photomagnetic effect in crossed electric and magnetic fields in thin (4 and 20 μm) InSb monocrystalline layers obtained from the melt by oriented crystallization are investigated. Possibility of controlling photomagnetic emf value by variation of the current value and polarity is shown

Thermoelectric properties of c-GeSb{sub 0.75}Te{sub 0.5} to h-GeSbTe{sub 0.5} thin films through annealing treatment effects

Energy Technology Data Exchange (ETDEWEB)

Vora-ud, Athorn, E-mail: athornvora-ud@snru.ac.th [Program of Physics, Faculty of Science and Technology, Sakon Nakhon Rajabhat University, Mueang District, Sakon Nakhon 47000 (Thailand); Thermoelectrics Research Center, Research and Development Institution, Sakon Nakhon Rajabhat University, Mueang District, Sakon Nakhon 47000 (Thailand); Horprathum, Mati, E-mail: mati.horprathum@nectec.or.th [National Electronics and Computer Technology Center, National Science and Technology Development Agency, Pathumthani 12120 (Thailand); Eiamchai, Pitak [National Electronics and Computer Technology Center, National Science and Technology Development Agency, Pathumthani 12120 (Thailand); Muthitamongkol, Pennapa; Chayasombat, Bralee; Thanachayanont, Chanchana [National Metal and Materials Technology Center, National Science and Technology Development Agency, Pathumthani 12120 (Thailand); Pankiew, Apirak [National Electronics and Computer Technology Center, National Science and Technology Development Agency, Pathumthani 12120 (Thailand); Klamchuen, Annop [National Nanotechnology Center, National Science and Technology Development Agency, Pathumthani 12120 (Thailand); Naenkieng, Daengdech; Plirdpring, Theerayuth; Harnwunggmoung, Adul [Thermoelectric and Nanotechnology Research Center, Faculty of Science and Technology, Rajamangala University of Technology Suvarnabhumi, Huntra Phranakhon, Si Ayutthaya 13000 (Thailand); Charoenphakdee, Anek [NANO-Thermoelectrics Research Center, Division of Applied Physics, Faculty of Sciences and Liberal Arts, Rajamangala University of Technology Isan, Mueng Nakorn Ratchasima 30000 Thailand (Thailand); Somkhunthot, Weerasak [Program of Physics, Faculty of Science and Technology, Loei Rajabhat University, Muang District, Loei 42000 (Thailand); and others

2015-11-15

Germanium–Antimony–Tellurium (Ge–Sb–Te) thin films were deposited on silicon wafers with 1-μm silicon dioxide (SiO{sub 2}/Si) by pulsed dc magnetron sputtering from a 99.99% GeSbTe target of 1:1:1 ratio at ambient temperature. The samples were annealed at 573, 623, 673, and 723 K for 3600 s in a vacuum state. The effects of the annealing treatment on phase identification, atomic composition, morphology and film thickness, carrier concentration, mobility, and Seebeck coefficient of the Ge–Sb–Te samples have been investigated by grazing-incidence X-ray diffraction, auger electron spectroscopy, field-emission scanning electron microscopy, Hall-effect measurements, and steady state method, respectively. The results demonstrated that the as-deposited Ge–Sb–Te sample was amorphous. Atomic composition of as-deposited and annealed films at 573 K and 623 K were GeSb{sub 0.75}Te{sub 0.5} while annealed films at 673 K and 723 K were GeSbTe{sub 0.5} due to Sb-rich GeSb{sub 0.75}Te{sub 0.5}. The samples annealed at 573 K and 623 K showed the crystal phases of cubic structure (c-GeSb{sub 0.75}Te{sub 0.5}) into hexagonal structure (h-GeSbTe{sub 0.5}) after annealing at 673 K and 723 K. The study demonstrated the insulating condition from the as-deposited GeSbTe film, and the changes towards the thermoelectric properties from the annealing treatments. The GeSbTe films annealed at 673 K yielded excellent thermoelectric properties with the electrical resistivity, Seebeck coefficient, and power factor at approximately 1.45 × 10{sup −5} Ωm, 71.07 μV K{sup −1}, and 3.48 × 10{sup −4} W m{sup −1} K{sup −2}, respectively. - Highlights: • GeSbTe thin films were successfully sputtered for thermoelectric properties. • GeSbTe films were examined among physical, electrical and thermoelectric properties. • Thermoelectric properties were discussed based on composition of the films.

Implementation of a anti-coincidence system of 4πNaI(Tl)-Cl and primary standardization of 57Co, 124Sb and 241Am

International Nuclear Information System (INIS)

Silva, Carlos Jose da; Iwahara, Akira; Poledna, Roberto; Oliveira, Estela Maria de; Prinzio, Maria Antonieta de; Lopes, Ricardo Tadeu

2009-01-01

The Radionuclide Metrology Laboratory of the IRD-Brazil, implemented a primary standardization system which utilizes the anti-coincidence technique with live time keeping. For testing the performance of these system it was made the standardization of the 57 Co, 124 Sb and 241 Am. Encourages results were obtained not only the standardization of 241 Am but also of the 124 Sb whose reference value obtained by the LNMRI was utilized for the key comparison organized by the IAEA and EURAMET. The standard uncertainties were of 0.28%, 0.22% and 0.13% for the 57 Co, 124 Sb and 241 Am, respectively

EPR and TL correlation in some powdered Greek white marbles

International Nuclear Information System (INIS)

Baieetto, Vanessa; Villeneuve, Gerard; Guibert, Pierre; Schvoerer, Max

2000-01-01

Thermoluminescence of white powdered marble samples, chosen to display different EPR spectra, were studied. Two peaks at 280 deg. C and 360 deg. C can be observed among the TL glow curves while the EPR spectra exhibit two signals: the A signal with g perp =2.0038 and g par =2.0024 due to the SO - 3 centre and the B one with g 1 =2.0005; g 2 =2.0001; g 3 =1.9998 due to mechanical powder reduction (drilling). Owing to heating and simultaneous experiments, a correlation have been established: the 280 deg. C TL peak is associated to the A signal and thus to the SO - 3 centre and the 360 deg. C TL peak is caused by mechanical treatment corresponding to the B EPR signal

EPR and TL correlation in some powdered Greek white marbles.

Science.gov (United States)

Baïetto, V; Villeneuve, G; Guibert, P; Schvoerer, M

2000-02-01

Thermoluminescence of white powdered marble samples, chosen to display different EPR spectra, were studied. Two peaks at 280 degrees C and 360 degrees C can be observed among the TL glow curves while the EPR spectra exhibit two signals: the A signal with g perpendicular = 2.0038 and g parallel = 2.0024 due to the SO3- centre and the B one with g1 = 2.0005; g2 = 2.0001; g3 = 1.9998 due to mechanical powder reduction (drilling). Owing to heating and simultaneous experiments, a correlation have been established: the 280 degrees C TL peak is associated to the A signal and thus to the SO3- centre and the 360 degrees C TL peak is caused by mechanical treatment corresponding to the B EPR signal.

Radiation-modified structure of Ge25Sb15S60 and Ge35Sb5S60 glasses

International Nuclear Information System (INIS)

Kavetskyy, T.; Shpotyuk, O.; Kaban, I.; Hoyer, W.

2008-01-01

Atomic structures of Ge 25 Sb 15 S 60 and Ge 35 Sb 5 S 60 glasses are investigated in the γ-irradiated and annealed after γ-irradiation states by means of high-energy synchrotron x-ray diffraction technique. The first sharp diffraction peak (FSDP) is detected at around 1.1 A -1 in the structure factors of both alloys studied. The FSDP position is found to be stable for radiation/annealing treatment of the samples, while the FSDP intensity shows some changes between γ-irradiated and annealed states. The peaks in the pair distribution functions observed between 2 and 4 A are related to the Ge-S, Ge-Sb, and Sb-Sb first neighbor correlations and Ge-Ge second neighbor correlations in the edge-shared GeS 4/2 tetrahedra, and S-S and/or Ge-Ge second neighbor correlations in the corner-shared GeS 4/2 tetrahedra. Three mechanisms of the radiation-/annealing-induced changes are discussed in the framework of coordination topological defect formation and bond-free solid angle concepts

Activation analysis of thallium in urine using the 203Tl(n,2n) 202Tl reaction

International Nuclear Information System (INIS)

Korob, R.O.; Cohen, I.M.; Lage, M.; Baro, G.B.

1976-04-01

The method developed by the authors of thallium determination in human urine, based on the 203 Tl(n,2n) 202 Tl reaction followed by chemical separation and measurement of the produced 202 Tl by gamma spectrometry, is described. Its application in some cases of intoxication by thallium is reported. The advantages and limitations of the described technique are discussed. (author) [es

Photoluminescence and structural properties of unintentional single and double InGaSb/GaSb quantum wells grown by MOVPE

Science.gov (United States)

Ahia, Chinedu Christian; Tile, Ngcali; Botha, Johannes R.; Olivier, E. J.

2018-04-01

The structural and photoluminescence (PL) characterization of InGaSb quantum well (QW) structures grown on GaSb substrate (100) using atmospheric pressure Metalorganic Vapor Phase Epitaxy (MOVPE) is presented. Both structures (single and double-InGaSb QWs) were inadvertently formed during an attempt to grow capped InSb/GaSb quantum dots (QDs). In this work, 10 K PL peak energies at 735 meV and 740 meV are suggested to be emissions from the single and double QWs, respectively. These lines exhibit red shifts, accompanied by a reduction in their full-widths at half-maximum (FWHM) as the excitation power decreases. The presence of a GaSb spacer in the double QW was found to increase the strength of the PL emission, which consequently gives rise to a reduced blue-shift and broadening of the PL emission line observed for the double QW with an increase in laser power, while the low thermal activation energy for the quenching of the PL from the double QW is attributed to the existence of threading dislocations, as seen in the bright field TEM image for this sample.

Thallium-rich pyrite ores from the Apuan Alps, Tuscany, Italy:constraints for their origin and environmental concerns

Science.gov (United States)

D'Orazio, Massimo; Biagioni, Cristian; Dini, Andrea; Vezzoni, Simone

2017-06-01

The southern sector of the Apuan Alps (AA) massif, Tuscany, Italy, is characterized by the occurrence of a series of baryte-pyrite-iron oxide orebodies whose Tl-rich nature was recognized only recently. The geochemistry of the pyrite ore was investigated through inductively coupled plasma mass spectrometry. In addition, lead isotope data for selected pyrite ores from AA were collected. Pyrite ores are characterized by a complex geochemistry, with high concentrations of Tl (up to 1100 μg/g) coupled with high As and Sb contents; the Co/Ni ratio is always <1. Geochemical data of pyrite and marcasite ore samples from other mining districts of Tuscany have been collected in order to compare them with those from the AA. These samples usually have very low Tl content (less than 2 μg/g) and high to very high Co/Ni and As/Sb ratios. Only some samples from the Sb-Hg ore deposits showed very high Tl concentrations (up to 3900 μg/g). Another difference is related to the lead isotope composition, with pyrite ores from AA markedly less radiogenic than those from the other deposits from Tuscany. Geochemical data of pyrite ores from AA give new insights on the genesis of the baryte-pyrite-iron oxide orebodies, relating their formation to low-temperature hydrothermal systems active during early Paleozoic; in addition, these data play a fundamental role in assessing the environmental impact of these deposits.

Thermal and x-ray studies on Tl2U(MoO4)3 and Tl4U(MoO4)4

International Nuclear Information System (INIS)

Dahale, N.D.; Keskar, Meera; Kulkarni, N.K.; Singh Mudher, K.D.

2006-01-01

In the quaternary Tl-U(IV)-Mo-O system, two new compounds namely Tl 2 U(MoO 4 ) 3 and Tl 4 U(MoO 4 ) 4 were prepared and characterized by powder X-ray diffraction and thermal methods. These compounds were prepared by solid state reactions of Tl 2 MoO 4 , UMoO 5 and MoO 3 in the required stoichiometric ratio at 500 deg C in evacuated sealed quartz ampoule. The XRD data of Tl 2 U(MoO 4 ) 3 and Tl 4 U(MoO 4 ) 4 were indexed on orthorhombic cell. TG curves of Tl 2 U(MoO 4 ) 3 and Tl 4 U(MoO 4 ) 4 did not show any weight change up to 700 deg C in an inert atmosphere. During heating in an inert atmosphere, Tl 2 U(MoO 4 ) 3 and Tl 4 U(MoO 4 ) 4 showed endothermic Dta peaks due to melting of the compounds at 519 and 565 deg C, respectively. (author)

An analysis of annual maximum streamflows in Terengganu, Malaysia using TL-moments approach

Science.gov (United States)

Ahmad, Ummi Nadiah; Shabri, Ani; Zakaria, Zahrahtul Amani

2013-02-01

TL-moments approach has been used in an analysis to determine the best-fitting distributions to represent the annual series of maximum streamflow data over 12 stations in Terengganu, Malaysia. The TL-moments with different trimming values are used to estimate the parameter of the selected distributions namely: generalized pareto (GPA), generalized logistic, and generalized extreme value distribution. The influence of TL-moments on estimated probability distribution functions are examined by evaluating the relative root mean square error and relative bias of quantile estimates through Monte Carlo simulations. The boxplot is used to show the location of the median and the dispersion of the data, which helps in reaching the decisive conclusions. For most of the cases, the results show that TL-moments with one smallest value was trimmed from the conceptual sample (TL-moments (1,0)), of GPA distribution was the most appropriate in majority of the stations for describing the annual maximum streamflow series in Terengganu, Malaysia.

Multielemental Determination of As, Bi, Ge, Sb, and Sn in Agricultural Samples Using Hydride Generation Coupled to Microwave-Induced Plasma Optical Emission Spectrometry.

Science.gov (United States)

Machado, Raquel C; Amaral, Clarice D B; Nóbrega, Joaquim A; Araujo Nogueira, Ana Rita

2017-06-14

A microwave-induced plasma optical emission spectrometer with N 2 -based plasma was combined with a multimode sample introduction system (MSIS) for hydride generation (HG) and multielemental determination of As, Bi, Ge, Sb, and Sn in samples of forage, bovine liver, powdered milk, agricultural gypsum, rice, and mineral fertilizer, using a single condition of prereduction and reduction. The accuracy of the developed analytical method was evaluated using certified reference materials of water and mineral fertilizer, and recoveries ranged from 95 to 106%. Addition and recovery experiments were carried out, and the recoveries varied from 85 to 117% for all samples evaluated. The limits of detection for As, Bi, Ge, Sb, and Sn were 0.46, 0.09, 0.19, 0.46, and 5.2 μg/L, respectively, for liquid samples, and 0.18, 0.04, 0.08, 0.19, and 2.1 mg/kg, respectively, for solid samples. The method proposed offers a simple, fast, multielemental, and robust alternative for successful determination of all five analytes in agricultural samples with low operational cost without compromising analytical performance.

Sorghum phytochrome B inhibits flowering in long days by activating expression of SbPRR37 and SbGHD7, repressors of SbEHD1, SbCN8 and SbCN12.

Directory of Open Access Journals (Sweden)

Shanshan Yang

Full Text Available Light signaling by phytochrome B in long days inhibits flowering in sorghum by increasing expression of the long day floral repressors PSEUDORESPONSE REGULATOR PROTEIN (SbPRR37, Ma1 and GRAIN NUMBER, PLANT HEIGHT AND HEADING DATE 7 (SbGHD7, Ma6. SbPRR37 and SbGHD7 RNA abundance peaks in the morning and in the evening of long days through coordinate regulation by light and output from the circadian clock. 58 M, a phytochrome B deficient (phyB-1, ma3R genotype, flowered ∼60 days earlier than 100 M (PHYB, Ma3 in long days and ∼11 days earlier in short days. Populations derived from 58 M (Ma1, ma3R, Ma5, ma6 and R.07007 (Ma1, Ma3, ma5, Ma6 varied in flowering time due to QTL aligned to PHYB/phyB-1 (Ma3, Ma5, and GHD7/ghd7-1 (Ma6. PHYC was proposed as a candidate gene for Ma5 based on alignment and allelic variation. PHYB and Ma5 (PHYC were epistatic to Ma1 and Ma6 and progeny recessive for either gene flowered early in long days. Light signaling mediated by PhyB was required for high expression of the floral repressors SbPRR37 and SbGHD7 during the evening of long days. In 100 M (PHYB the floral activators SbEHD1, SbCN8 and SbCN12 were repressed in long days and de-repressed in short days. In 58 M (phyB-1 these genes were highly expressed in long and short days. Furthermore, SbCN15, the ortholog of rice Hd3a (FT, is expressed at low levels in 100 M but at high levels in 58 M (phyB-1 regardless of day length, indicating that PhyB regulation of SbCN15 expression may modify flowering time in a photoperiod-insensitive manner.

Self-diffusion in 69Ga121Sb/71Ga123Sb isotope heterostructures

Science.gov (United States)

Bracht, H.; Nicols, S. P.; Haller, E. E.; Silveira, J. P.; Briones, F.

2001-05-01

Gallium and antimony self-diffusion experiments have been performed in undoped 69Ga121Sb/71Ga123Sb isotope heterostructures at temperatures between 571 and 708 °C under Sb- and Ga-rich ambients. Ga and Sb profiles measured with secondary ion mass spectrometry reveal that Ga diffuses faster than Sb by several orders of magnitude. This strongly suggests that the two self-atom species diffuse independently on their own sublattices. Experimental results lead us to conclude that Ga and Sb diffusion are mediated by Ga vacancies and Sb interstitials, respectively, and not by the formation of a triple defect proposed earlier by Weiler and Mehrer [Philos. Mag. A 49, 309 (1984)]. The extremely slow diffusion of Sb up to the melting temperature of GaSb is proposed to be a consequence of amphoteric transformations between native point defects which suppress the formation of those native defects which control Sb diffusion. Preliminary experiments exploring the effect of Zn indiffusion at 550 °C on Ga and Sb diffusion reveal an enhanced intermixing of the Ga isotope layers compared to undoped GaSb. However, under the same conditions the diffusion of Sb was not significantly affected.

Estimating distribution parameters of annual maximum streamflows in Johor, Malaysia using TL-moments approach

Science.gov (United States)

Mat Jan, Nur Amalina; Shabri, Ani

2017-01-01

TL-moments approach has been used in an analysis to identify the best-fitting distributions to represent the annual series of maximum streamflow data over seven stations in Johor, Malaysia. The TL-moments with different trimming values are used to estimate the parameter of the selected distributions namely: Three-parameter lognormal (LN3) and Pearson Type III (P3) distribution. The main objective of this study is to derive the TL-moments ( t 1,0), t 1 = 1,2,3,4 methods for LN3 and P3 distributions. The performance of TL-moments ( t 1,0), t 1 = 1,2,3,4 was compared with L-moments through Monte Carlo simulation and streamflow data over a station in Johor, Malaysia. The absolute error is used to test the influence of TL-moments methods on estimated probability distribution functions. From the cases in this study, the results show that TL-moments with four trimmed smallest values from the conceptual sample (TL-moments [4, 0]) of LN3 distribution was the most appropriate in most of the stations of the annual maximum streamflow series in Johor, Malaysia.

Tl-201 per rectum scintigraphy in chronic liver disease: assessment of Tl-201 uptake indices

International Nuclear Information System (INIS)

Moon, Won Jin; Choi, Yun Young; Cho, Suk Shin; Lee, Min Ho

1999-01-01

Heart to liver ratio on Tl-201 per rectal scintigraphy (shunt index) is known to be useful in the assessment of portal systemic shunt. We assessed Tl-201 uptake pattern and early liver/heart uptake rate of Tl-201 and correlated with shunt index in patients with chronic active hepatitis (CAH) and liver cirrhosis (LC). Fifty eight patients with biopsy-proven chronic liver disease (35 with CAH, 23 with LC) underwent Tl-201 per rectum scintigraphy after instillation of 18.5 MBq of Tl-201 into the upper rectum. We evaluated hepatic uptake (type 1: homogeneous, 2: inhomogeneous segmental, 3: inhomogeneous nonsegmental) and extrahepatic uptake of spleen, heart and kidney (grade 0: no uptake, 1: less than liver, 2: equal to liver, 3: greater than liver). We measured the early liver/heart uptake rate (the slope of the liver to heart uptake ratio for 10 mim) and shunt index (heart to liver uptake ratio). Tl-201 uptake pattern and early liver/heart uptake rate of Tl-201 was correlated with the pathologic diagnosis and shunt index. Hepatic uptake patterns of type 1 and 2 were dominant in CAH (CAH: 27/35, LC: 8/23), and type 3 in LC (CAH: 8/35, LC: 15/23)(p<0.005). The grades of extrahepatic uptake were higher in LC than in CAH (spleen: p<0.001, other soft tissue: p<0.005). The early liver/heart uptake rate of CAH (0.110±0.111) was significantly higher than that of LC (0.014±0.090)(p<0.001). The sensitivity and specificity of the early liver/heart uptake rate were 77.7% and 67.7% in differentiating LC from CAH. There was negative correlation between early liver/heart uptake rate and shunt index (r=-0.3347, p<0.01). Hepatic and extrahepatic uptake pattern and early liver/heart uptake rate on Tl-201 per rectum scintigraphy are useful in the assessment of portal systemic shunt in patients with chronic liver disease

A 121Sb Moessbauer Study of the Chemical State of Antimony in V-Sb-O Mixed-Oxide Catalysts for the Ammoxidation of Propane

International Nuclear Information System (INIS)

Stievano, L.; Wagner, F. E.; Zanthoff, H. W.; Calogero, S.

2002-01-01

The structural changes of two representative samples of a group of V-Sb-oxide catalysts, a vanadium-rich and an antimony-rich specimen, are investigated by 121 Sb Moessbauer spectroscopy after treatment under propene or hydrogen at 673 K. The as-prepared catalysts contain both Sb(V) and Sb(III) as crystalline and microcrystalline α-Sb 2 O 4 and VSbO 4 , as well as an additional amorphous V 5+ oxide phase. The oxidation state of antimony does not change upon exposure to propene, whereas a partial reduction can be obtained by a more intense reduction under hydrogen. The Moessbauer results indicate that the antimony in VSbO 4 can be reduced more easily than that in α-Sb 2 O 4 , which appears to be more stable. These results are discussed in view of the observed depletion of vanadium at the surface of the catalyst particles under reaction conditions.

Insight on a novel layered semiconductors: CuTlS and CuTlSe

Energy Technology Data Exchange (ETDEWEB)

Aliev, Ziya S., E-mail: ziyasaliev@gmail.com [Institute of Catalysis and Inorganic Chemistry, ANAS, H.Javid ave. 113, AZ1143 Baku (Azerbaijan); Institute of Physics, ANAS, H.Javid ave. 131, AZ1143 Baku (Azerbaijan); Donostia International Physics Center (DIPC), 20080 San Sebastian (Spain); Zúñiga, Fco. Javier [Departamento de Física de la Materia Condensada, Facultad de Ciencia y Tecnología, Universidad del País Vasco, Apdo. 644, 48080 Bilbao (Spain); Koroteev, Yury M. [Institute of Strength Physics and Materials Science, Russian Academy of Sciences, Siberian Branch, 634055 Tomsk (Russian Federation); Tomsk State University, Tomsk, 634050 (Russian Federation); Breczewski, Tomasz [Departamento de Física de la Materia Condensada, Facultad de Ciencia y Tecnología, Universidad del País Vasco, Apdo. 644, 48080 Bilbao (Spain); Babanly, Nizamaddin B. [Institute of Catalysis and Inorganic Chemistry, ANAS, H.Javid ave. 113, AZ1143 Baku (Azerbaijan); Amiraslanov, Imamaddin R. [Institute of Physics, ANAS, H.Javid ave. 131, AZ1143 Baku (Azerbaijan); Politano, Antonio [Department of Physics, University of Calabria, 87036 Rende (CS) (Italy); Madariaga, Gotzon [Departamento de Física de la Materia Condensada, Facultad de Ciencia y Tecnología, Universidad del País Vasco, Apdo. 644, 48080 Bilbao (Spain); Babanly, Mahammad B. [Institute of Catalysis and Inorganic Chemistry, ANAS, H.Javid ave. 113, AZ1143 Baku (Azerbaijan); and others

2016-10-15

Single crystals of the ternary copper compounds CuTlS and CuTlSe have been successfully grown from stoichiometric melt by using vertical Bridgman-Stockbarger method. The crystal structure of the both compounds has been determined by powder and single crystal X-Ray diffraction. They crystallize in the PbFCl structure type with two formula units in the tetragonal system, space group P4/nmm, a=3.922(2); c=8.123(6); Z=2 and a=4.087(6); c=8.195(19) Å; Z=2, respectively. The band structure of the reported compounds has been analyzed by means of full-potential linearized augmented plane-wave (FLAPW) method based on the density functional theory (DFT). Both compounds have similar band structures and are narrow-gap semiconductors with indirect band gap. The resistivity measurements agree with a semiconductor behavior although anomalies are observed at low temperature. - Graphical abstract: The crystal structures of CuTl and CuTlSe are isostructural with the PbFCl-type and the superconductor LiFeAs-type tetragonal structure. The band structure calculations confirmed that they are narrow-gap semiconductors with indirect band gaps of 0.326 and 0.083 eV. The resistivity measurements, although confirming the semiconducting behavior of both compounds exhibit unusual anomalies at low temperatures. - Highlights: • Single crystals of CuTlS and CuTlSe have been successfully grown by Bridgman-Stockbarger method. • The crystal structure of the both compounds has been determined by single crystal XRD. • The band structure of the both compounds has been analyzed based on the density functional theory (DFT). • The resistivity measurements have been carried out from room temperature down to 10 K.

EPR and TL correlation in some powdered Greek white marbles

Energy Technology Data Exchange (ETDEWEB)

Baieetto, Vanessa E-mail: crpaa@montaigne.u-bordeaux.fr; Villeneuve, Gerard; Guibert, Pierre; Schvoerer, Max

2000-02-01

Thermoluminescence of white powdered marble samples, chosen to display different EPR spectra, were studied. Two peaks at 280 deg. C and 360 deg. C can be observed among the TL glow curves while the EPR spectra exhibit two signals: the A signal with g{sub perp}=2.0038 and g{sub par} =2.0024 due to the SO{sup -}{sub 3} centre and the B one with g{sub 1}=2.0005; g{sub 2}=2.0001; g{sub 3}=1.9998 due to mechanical powder reduction (drilling). Owing to heating and simultaneous experiments, a correlation have been established: the 280 deg. C TL peak is associated to the A signal and thus to the SO{sup -}{sub 3} centre and the 360 deg. C TL peak is caused by mechanical treatment corresponding to the B EPR signal.

Investigation of TL properties of sand collected from sewage sludge as an ''in situ'' dosimeter in radiation disinfection

International Nuclear Information System (INIS)

Benny, P.G.; Bhatt, B.C.

1996-01-01

Thermoluminescence (TL) properties of sand, collected from sewage sludge, were studied after extensive cleaning procedures. In the sand samples treated with either hydrogen peroxide (H 2 O 2 ) or hydrofluoric acid (HF), there was a prominent TL peak at about 220 o C after γ-irradiation and 120 o C, 20 min post-irradiation annealing treatment. The dose vs TL response curves in hydrogen-peroxide-treated and HF-treated sand samples were found to be linear up to 30 and 100 Gy, respectively, beyond which they were supra-linear. The extent of post-irradiation fading in the sand sample, which was treated with H 2 O 2 and post-irradiation annealed at 120 o C for 20 min, was observed to be 8% after 21 days, while no detectable fading was observed for the sample which was HF treated and annealed at 120 o C for 20 min after γ-irradiation. Therefore, H 2 O 2 - as well as HF-treated sludge sand samples could be considered for use as in situ TL dosimeters for radiation disinfection of sewage sludge. (Author)

The correlation of fast OSL component with the TL peak at 3250C in quartz of various origins

International Nuclear Information System (INIS)

Kitis, G.; Kiyak, N.; Polymeris, G.S.; Tsirliganis, N.C.

2010-01-01

The fast component of the optically stimulated luminescence (OSL) signal in quartz is the basic tool for the optical dating. Its relation with the thermoluminescence (TL) glow-peak at about 325 deg. C is well established for naturally irradiated quartz. This relationship is also an important part of a general model for quartz on which many theoretical simulations of various OSL experimental results have been based. In the present work this relationship is systematically investigated in nine quartz samples of different origin. The linearly modulated OSL (LM-OSL) curves of all quartz samples for stimulation time less than 50 s consists of two components discriminated easily by a computerized curve deconvolution (CCD) analysis. By comparing the un-bleached to the respective bleached TL glow-curve, it is found that the system of these two fast OSL components is directly related with only a small portion of the electron traps responsible for the TL glow-peaks in the temperature region 200-400 0 C. By increasing the stimulation times, besides the two fast components, the medium and the slow components are also obtained. The medium and slow components are clearly related with the main body of the electron traps responsible for TL glow-peaks in the same temperature region 200-400 0 C. Despite their different origin all quartz samples show an appreciable homogeneity concerning the number and time position of the individual components, whereas, the relative TL/OSL intensities vary strongly from sample to sample with the integrated TL intensity being generally much less than the integrated OSL intensity.

TL, EPR and optical absorption in natural grossular crystal

Energy Technology Data Exchange (ETDEWEB)

Yauri, J.M. [Institute of Physics, University of Sao Paulo, Rua do Matao, Travessa R, 187, CEP 05508-900, Sao Paulo (Brazil); Department of Physics, University of San Agustin, Av. Independencia S/N, Arequipa (Peru); Cano, N.F. [Institute of Physics, University of Sao Paulo, Rua do Matao, Travessa R, 187, CEP 05508-900, Sao Paulo (Brazil)], E-mail: nilocano@dfn.if.usp.br; Watanabe, S. [Institute of Physics, University of Sao Paulo, Rua do Matao, Travessa R, 187, CEP 05508-900, Sao Paulo (Brazil)

2008-10-15

Grossular is one of six members of silicate Garnet group. Two samples GI and GII have been investigated concerning their luminescence thermally stimulated (TL). EPR and optical absorption and the measurements were carried out to find out whether or not same point defects are responsible for all three properties. Although X-rays diffraction analysis has shown that both GI and GII have practically the same crystal structure of a standard grossular crystal, they presented different behavior in many aspects. The TL glow curve shape, TL response to radiation dose, the effect of annealing at high temperatures before irradiation, the dependence of UV bleaching parameters on peak temperature, all of them differ going from GI to GII. The EPR signals around g=2.0 as well as at g=4.3 and 6.0 have much larger intensity in GI than in GII. Very high temperature (>800 deg. C) annealing causes large increase in the bulk background absorption in GI, however, only very little in GII. In the cases of EPR and optical absorption, the difference in their behavior can be attributed to Fe{sup 3+} ions; however, in the TL case one cannot and the cause was not found as yet.

TL, EPR and optical absorption in natural grossular crystal

International Nuclear Information System (INIS)

Yauri, J.M.; Cano, N.F.; Watanabe, S.

2008-01-01

Grossular is one of six members of silicate Garnet group. Two samples GI and GII have been investigated concerning their luminescence thermally stimulated (TL). EPR and optical absorption and the measurements were carried out to find out whether or not same point defects are responsible for all three properties. Although X-rays diffraction analysis has shown that both GI and GII have practically the same crystal structure of a standard grossular crystal, they presented different behavior in many aspects. The TL glow curve shape, TL response to radiation dose, the effect of annealing at high temperatures before irradiation, the dependence of UV bleaching parameters on peak temperature, all of them differ going from GI to GII. The EPR signals around g=2.0 as well as at g=4.3 and 6.0 have much larger intensity in GI than in GII. Very high temperature (>800 deg. C) annealing causes large increase in the bulk background absorption in GI, however, only very little in GII. In the cases of EPR and optical absorption, the difference in their behavior can be attributed to Fe 3+ ions; however, in the TL case one cannot and the cause was not found as yet

Prediction of half-metallic properties in TlCrS{sub 2} and TlCrSe{sub 2} based on density functional theory

Energy Technology Data Exchange (ETDEWEB)

Hashimzade, F.M.; Huseinova, D.A. [Institute of Physics, National Academy of Sciences of Azerbaijan, AZ 1143 Baku (Azerbaijan); Jahangirli, Z.A. [Institute of Physics, National Academy of Sciences of Azerbaijan, AZ 1143 Baku (Azerbaijan); Institute of Radiation Problems, National Academy of Sciences of Azerbaijan, AZ 1143 Baku (Azerbaijan); Mehdiyev, B.H., E-mail: bachschi@yahoo.de [Institute of Physics, National Academy of Sciences of Azerbaijan, AZ 1143 Baku (Azerbaijan)

2017-08-01

Highlights: • Half-metallic properties of TlCrS2, TlCrSe2 and hypothetical TlCrSSe have been investigated by first-principles all-electron full-potential linearized augmented plane wave plus local orbital (FP-LAPW+lo) method based on density functional theory (DFT). • Total magnetic moment keeps its integer value on a relatively wide range of changes in volume (−10% ÷ 10%) for TlCrS2 and TlCrSSe, while total magnetic moment TlCrSe2 decreases with increasing volume, approaching to integer value 3 μB. • The states at the Fermi level in the case of spin-up channel consist of a hybridization of p-states of the atom S(Se) with d-states of Cr. - Abstract: Half-metallic properties of TlCrS{sub 2}, TlCrSe{sub 2} and hypothetical TlCrSSe have been investigated by first-principles all-electron full-potential linearized augmented plane wave plus local orbital (FP-LAPW+lo) method based on density functional theory (DFT). The results of calculations show that TlCrS{sub 2} and TlCrSSe are half-metals with energy gap (E{sub g}) ∼0.12 eV for spin-down channel. Strong hybridization of p-state of chalchogen and d-state of Cr leads to bonding and antibonding states and subsequently to the appearance of a gap in spin-down channel of TlCrS{sub 2} and TlCrSSe. In the case of TlCrSe{sub 2}, there is a partial hybridization and p-state is partially present in the DOS at Fermi level making this compound nearly half-metallic. The present calculations revealed that total magnetic moment keeps its integer value on a relatively wide range of changes in volume (−10% ÷ 10%) for TlCrS{sub 2} and TlCrSSe, while total magnetic moment of TlCrSe{sub 2} decreases with increasing volume approaching to integer value 3 μB.

Emission properties of thermoluminescence from natural quartz - blue and red TL response to absorbed dose

International Nuclear Information System (INIS)

Hashimoto, T.; Yokosaka, K.; Habuki, H.

1987-01-01

The TL spectrometry of natural quartz exposed to a gamma radiation dose of 8.8 kGy proved that the red TL, mainly from volcanically originated quartz, has a broad emission band with a peak around 620 nm, while the blue TL from plutonically originated quartz also has a broad emission band giving a peak around 470 nm. These typical red or blue intrinsic colours were also confirmed on the thermoluminescence colour images (TLCI). Exceptionally, a pegmatite quartz changed its TLCI colour from red to blue when the absorbed dose was increased. By using colour filter assemblies, all these quartz samples were shown to emit mainly blue and red TLs, which have distinctly different TL responses to the absorbed dose; the blue invariably showed a supralinearity relation between 1 and 10 kGy dose. For the purpose of dating, the use of red TL, is preferable. The red TL component is related to the impurity Eu content in quartz minerals. (author)

Analysis of liquid samples using dried-droplet laser ablation inductively coupled plasma mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Do, Trong-Mui; Hsieh, Hui-Fang; Chang, Wei-Ciang [Department of Biomedical Engineering and Environmental Sciences, National Tsing Hua University, Hsinchu, 30013 Taiwan (China); Chang, E.-E. [Department of Biochemistry, Taipei Medical University, Taipei City, 11031 Taiwan (China); Wang, Chu-Fang, E-mail: cfwang@mx.nthu.edu.tw [Department of Biomedical Engineering and Environmental Sciences, National Tsing Hua University, Hsinchu, 30013 Taiwan (China); Institute of Nuclear Engineering and Science, National Tsing Hua University, Hsinchu 30013, Taiwan (China)

2011-08-15

In this study we developed a dried-droplet method for laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). The proposed method provides accurate and precise results when building calibration curves and determining elements of interest in real liquid samples. After placing just 1 {mu}L of a liquid standard solution or a real sample onto the filter surface and then converting the solution into a very small, thin dry spot, the sample could be applied as an analytical subject for LA. To demonstrate the feasibility of this proposed method, we used LA-ICP-MS and conventional ICP-MS to determine the levels of 13 elements (Li, V, Mn, Co, Ni, Cu, Zn, As, Mo, Cd, Sb, Tl, and Pb) in five water samples. The correlation coefficients obtained from the various calibration curves ranged from 0.9920 ({sup 205}Tl) to 0.9998 ({sup 51}V), sufficient to allow the determination of a wide range of elements in the samples. We also investigated the effects of Methylene Blue (MB) and the NaCl concentration on the elemental analyses. MB could be used as an indicator during the ablation process; its presence in the samples only negligibly influenced the intensities of the signals of most of the tested elements. Notably, high NaCl contents led to signal suppression for some of the elements. In comparison with the established sample introduction by nebulization, our developed technique abrogates the need for time-consuming sample preparation and reduces the possibility of sample contamination.

Implementation of a anti-coincidence system of 4{pi}NaI(Tl)-Cl and primary standardization of {sup 57}Co, {sup 124}Sb and {sup 241}Am; Implementacao de um sistema de anti-coincidencia 4{pi}NaI(Tl)-Cl e padronizacao primaria do {sup 57}Co, {sup 124}Sb e {sup 241}Am

Energy Technology Data Exchange (ETDEWEB)

Silva, Carlos Jose da; Iwahara, Akira; Poledna, Roberto; Oliveira, Estela Maria de; Prinzio, Maria Antonieta de, E-mail: carlos@ird.gov.b [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Lopes, Ricardo Tadeu [Coordenacao dos Programas de Pos-Graduacao de Engenharia (LIN/COPPE/UFRJ), RJ (Brazil). Lab. de Instrumentacao Nuclear

2009-07-01

The Radionuclide Metrology Laboratory of the IRD-Brazil, implemented a primary standardization system which utilizes the anti-coincidence technique with live time keeping. For testing the performance of these system it was made the standardization of the {sup 57}Co, {sup 124}Sb and {sup 241}Am. Encourages results were obtained not only the standardization of {sup 241}Am but also of the {sup 124}Sb whose reference value obtained by the LNMRI was utilized for the key comparison organized by the IAEA and EURAMET. The standard uncertainties were of 0.28%, 0.22% and 0.13% for the {sup 57}Co, {sup 124}Sb and {sup 241}Am, respectively

On the determination of iridium in diverse geological samples employing HPGe-coincidence/NaI(Tl)-anticoincidence spectrometry

Science.gov (United States)

Murali, A. V.; Parekh, P. P.; Cumming, J. B.

1990-01-01

This paper reports the Ir content of a variety of geological samples determined by the high-purity Ge-coincidence/NaI(Tl)-anticoincidence gamma-ray spectrometry (henceforth referred to as coincidence/anticoincidence technique) and by the conventional INAA. The advantages of this technique are: (1) the Ir content of the samples is obtained (ppm to a fraction of ppb ranges) not only by the 468.1 keV peak as in the conventional INAA but also by the 784.6 keV and 920.9 keV sum peaks, which gives more confidence in the values obtained; and (2) it is well suited for the samples with high Compton background for which it is difficult to measure the Ir content by the conventional INAA technique. The practical sensitivity of this technique depends on the sample matrix. Under present experimental conditions, it varied from 0.1 ng for Mn nodules and 0.004 ng for Libyan Desert Glass. Iridium values obtained on small (about 1 microg) olivine grains demonstrate the potential application of this new technique to microsamples. The principle and methodology of this new technique as well as its advantages and disadvantages over the conventional INAA are discussed.

The {sup 124}Sb activity standardization by gamma spectrometry for medical applications

Energy Technology Data Exchange (ETDEWEB)

Almeida, M.C.M. de, E-mail: marcandida@yahoo.com.b [Laboratorio Nacional de Metrologia das Radiacoes Ionizantes, Instituto de Radioprotecao e Dosimetria, Comissao Nacional de Energia Nuclear (SEMRA/LNMRI/IRD/CNEN), Av. Salvador Allende s/n, Recreio, Rio de Janeiro, RJ, CEP 22780-160 (Brazil); Iwahara, A.; Delgado, J.U.; Poledna, R.; Silva, R.L. da [Laboratorio Nacional de Metrologia das Radiacoes Ionizantes, Instituto de Radioprotecao e Dosimetria, Comissao Nacional de Energia Nuclear (SEMRA/LNMRI/IRD/CNEN), Av. Salvador Allende s/n, Recreio, Rio de Janeiro, RJ, CEP 22780-160 (Brazil)

2010-07-21

This work describes a metrological activity determination of {sup 124}Sb, which can be used as radiotracer, applying gamma spectrometry methods with hyper pure germanium detector and efficiency curves. This isotope with good activity and high radionuclidic purity is employed in the form of meglumine antimoniate (Glucantime) or sodium stibogluconate (Pentostam) to treat leishmaniasis. {sup 124}Sb is also applied in animal organ distribution studies to solve some questions in pharmacology. {sup 124}Sb decays by {beta}-emission and it produces several photons (X and gamma rays) with energy varying from 27 to 2700 keV. Efficiency curves to measure point {sup 124}Sb solid sources were obtained from a {sup 166m}Ho standard that is a multi-gamma reference source. These curves depend on radiation energy, sample geometry, photon attenuation, dead time and sample-detector position. Results for activity determination of {sup 124}Sb samples using efficiency curves and a high purity coaxial germanium detector were consistent in different counting geometries. Also uncertainties of about 2% (k=2) were obtained.

AG, TL, and IRSL dosimetric properties in X-ray irradiated HPHT diamond crystals

Energy Technology Data Exchange (ETDEWEB)

Gil-Tolano, M.I. [Programa de Posgrado, Departamento de Investigacion en Fisica, Universidad de Sonora, A. P. 5-088, Hermosillo, Sonora, 83190, Mexico (Mexico); Melendrez, R.; Lancheros-Olmos, J.C.; Soto-Puebla, D.; Chernov, V.; Pedroza-Montero, M.; Barboza-Flores, M. [Departamento de Investigacion en Fisica, Universidad de Sonora, A. P. 5-088, Hermosillo, Sonora, 83190, Mexico (Mexico); Castaneda, B. [Departamento de Fisica, Universidad de Sonora, Blvd. Luis Encinas y Rosales S/N, Hermosillo, Sonora, 83000, Mexico (Mexico)

2014-10-15

HPHT diamonds have been studied for several years for their potential in different applications. In previous studies it has been found that the thermoluminescence (TL) glow curves of ''as-grown'' HPHT diamonds are non-reproducible. In this work, we study the afterglow (AG), thermoluminescent (TL), and optically stimulated luminescence (OSL) response of commercial samples of synthetic HPHT type-Ib diamond crystals exposed to X-ray irradiation (0.75 mA, 35 kV) at a dose rate of 0.624 Gy/s, after a high gamma ({sup 60}Co) dose irradiation of 500 kGy followed by a thermal treatment at 1073 K for 1 h in nitrogen atmosphere. Deconvolution of the TL glow curves shows four peaks, located around 379, 509, 561, and 609 K. The crystals exhibit evident AG recorded for 300 s immediately after X-ray irradiation, due to the thermal emptying of the traps responsible for the low-temperature TL peaks (below 400 K). The stimulation of irradiated crystals with 870-nm light, creates pronounced OSL and destroys all TL peaks with the exception of the high-temperature peak at 609 K. The dose responses of the integrated AG, TL, and OSL are linear in the range of 0.6-5 Gy and saturated at higher doses. The reproducibility of AG, TL, and OSL measurements is about 5%. The fading in the first hour of storage in dark conditions at RT of TL signal of HPHT diamond is mainly associated to the emptying of the traps responsible for the 379-K TL peaks. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Synthesis and Thermoelectric Properties of Ni-Doped ZrCoSb Half-Heusler Compounds

Directory of Open Access Journals (Sweden)

Degang Zhao

2018-01-01

Full Text Available The Ni-doped ZrCo1−xNixSb half-Heusler compounds were prepared by arc-melting and spark plasma sintering technology. X-ray diffraction analysis results showed that all samples were crystallized in a half-Heusler phase. Thermoelectric properties of ZrCo1−xNixSb compounds were measured from room temperature to 850 K. The electrical conductivity and the absolute value of Seebeck coefficient increased with the Ni-doping content increasing due to the Ni substitution at Co. sites. The lattice thermal conductivity of ZrCo1−xNixSb samples was depressed dramatically because of the acoustic phonon scattering and point defect scattering. The figure of merit of ZrCo1−xNixSb compounds was improved due to the decreased thermal conductivity and improved power factor. The maximum ZT value of 0.24 was achieved for ZrCo0.92Ni0.08Sb sample at 850 K.

NaI(Tl) electron energy resolution

CERN Document Server

Mengesha, W

2002-01-01

NaI(Tl) electron energy resolution eta sub e was measured using the Modified Compton Coincidence Technique (MCCT). The MCCT allowed detection of nearly monoenergetic internal electrons resulting from the scattering of incident 662 keV gamma rays within a primary NaI(Tl) detector. Scattered gamma rays were detected using a secondary HPGe detector in a coincidence mode. Measurements were carried out for electron energies ranging from 16 to 438 keV, by varying the scattering angle. Measured HPGe coincidence spectra were deconvolved to determine the scattered energy spectra from the NaI(Tl) detector. Subsequently, the NaI(Tl) electron energy spectra were determined by subtracting the energy of scattered spectra from the incident source energy (662 keV). Using chi-squared minimization, iterative deconvolution of the internal electron energy spectra from the measured NaI(Tl) spectra was then used to determine eta sub e at the electron energy of interest. eta sub e values determined using this technique represent va...

Copper interactions in TlCu7S4 and TlCu7Se4

International Nuclear Information System (INIS)

Noren, L.; Delaplane, R.G.; Berger, R.

1999-01-01

Complete text of publication follows. The copper chalcogenides ACu 7 S 4 (A=NH 4 + , Tl + , Rb + ) are quasi-one-dimensional metals at ambient and higher temperatures which is due to the high mobility of copper in these structures. TlCu 7 S 4 and TlCu 7 Se 4 are isostructural compounds, space group I4/m, which can be described on the basis of a TlX 8 cube with two different Cu sites, Cu(1) and Cu(2). Cu(2)-Cu(2) zigzag chains run along the c axis with only 3/4 occupation of the Cu(2) sites. However, these two compounds differ in behaviour on cooling. The sulphide shows a polymorphic first-order transition to the CsAg 7 S 4 type (P4/n) owing to ordering of the vacancies in the Cu(2)-Cu(2) chains. In order to study the nature of the Cu(2) order/disorder in the two title compounds, a series of neutron diffraction measurements (both Bragg and diffuse scattering) were made at several temperatures from 40 to 713 K on the instrument SLAD at Studsvik. The structure at each temperature was modelled using RMC techniques. The resulting configuration show that as the temperature increases, there is a marked increase in the mobility of the Cu atoms in the Cu(2)-Cu(2) chains for TlCu 7 S 4 but not for TlCu 7 Se 4 . This is due to the initial difference in the Cu(2)-Cu(2) distances, only 2.2A for the thiocuprate, but 2.7A in the selenocuprate which explains the relative ease for Cu(2) ordering in the latter case. (author)

[Tl(III)(dota)](-): An Extraordinarily Robust Macrocyclic Complex.

Science.gov (United States)

Fodor, Tamás; Bányai, István; Bényei, Attila; Platas-Iglesias, Carlos; Purgel, Mihály; Horváth, Gábor L; Zékány, László; Tircsó, Gyula; Tóth, Imre

2015-06-01

The X-ray structure of {C(NH2)3}[Tl(dota)]·H2O shows that the Tl(3+) ion is deeply buried in the macrocyclic cavity of the dota(4-) ligand (1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetate) with average Tl-N and Tl-O distances of 2.464 and 2.365 Å, respectively. The metal ion is directly coordinated to the eight donor atoms of the ligand, which results in a twisted square antiprismatic (TSAP') coordination around Tl(3+). A multinuclear (1)H, (13)C, and (205)Tl NMR study combined with DFT calculations confirmed the TSAP' structure of the complex in aqueous solution, which exists as the Λ(λλλλ)/Δ(δδδδ) enantiomeric pair. (205)Tl NMR spectroscopy allowed the protonation constant associated with the protonation of the complex according to [Tl(dota)](-) + H(+) ⇆ [Tl(Hdota)] to be determined, which turned out to be pK(H)Tl(dota) = 1.4 ± 0.1. [Tl(dota)](-) does not react with Br(-), even when using an excess of the anion, but it forms a weak mixed complex with cyanide, [Tl(dota)](-) + CN(-) ⇆ [Tl(dota)(CN)](2-), with an equilibrium constant of Kmix = 6.0 ± 0.8. The dissociation of the [Tl(dota)](-) complex was determined by UV-vis spectrophotometry under acidic conditions using a large excess of Br(-), and it was found to follow proton-assisted kinetics and to take place very slowly (∼10 days), even in 1 M HClO4, with the estimated half-life of the process being in the 10(9) h range at neutral pH. The solution dynamics of [Tl(dota)](-) were investigated using (13)C NMR spectroscopy and DFT calculations. The (13)C NMR spectra recorded at low temperature (272 K) point to C4 symmetry of the complex in solution, which averages to C4v as the temperature increases. This dynamic behavior was attributed to the Λ(λλλλ) ↔ Δ(δδδδ) enantiomerization process, which involves both the inversion of the macrocyclic unit and the rotation of the pendant arms. According to our calculations, the arm-rotation process limits the Λ(λλλλ) ↔ �

Density functional simulations of Sb-rich GeSbTe phase change alloys

International Nuclear Information System (INIS)

Gabardi, S; Bernasconi, M; Caravati, S; Parrinello, M

2012-01-01

We generated models of the amorphous phase of Sb-rich GeSbTe phase change alloys by quenching from the melt within density functional molecular dynamics. We considered the two compositions Ge 1 Sb 1 Te 1 and Ge 2 Sb 4 Te 5 . Comparison with previous results on the most studied Ge 2 Sb 2 Te 5 allowed us to draw some conclusions on the dependence of the structural properties of the amorphous phase on the alloy composition. Vibrational and electronic properties were also scrutinized. Phonons at high frequencies above 200 cm -1 are localized in tetrahedra around Ge atoms in Sb-rich compounds as well as in Ge 2 Sb 2 Te 5 . All compounds are semiconducting in the amorphous phase, with a band gap in the range 0.7-1.0 eV.

Density functional simulations of Sb-rich GeSbTe phase change alloys

Science.gov (United States)

Gabardi, S.; Caravati, S.; Bernasconi, M.; Parrinello, M.

2012-09-01

We generated models of the amorphous phase of Sb-rich GeSbTe phase change alloys by quenching from the melt within density functional molecular dynamics. We considered the two compositions Ge1Sb1Te1 and Ge2Sb4Te5. Comparison with previous results on the most studied Ge2Sb2Te5 allowed us to draw some conclusions on the dependence of the structural properties of the amorphous phase on the alloy composition. Vibrational and electronic properties were also scrutinized. Phonons at high frequencies above 200 cm-1 are localized in tetrahedra around Ge atoms in Sb-rich compounds as well as in Ge2Sb2Te5. All compounds are semiconducting in the amorphous phase, with a band gap in the range 0.7-1.0 eV.

Ultrashort-period lateral composition modulation in TlInGaAsN/TlInP structures

International Nuclear Information System (INIS)

Ishimaru, Manabu; Tanaka, Yuusuke; Hasegawa, Shigehiko; Asahi, Hajime; Sato, Kazuhisa; Konno, Toyohiko J.

2009-01-01

We prepared TlInGaAsN/TlInP quantum well structures using gas source molecular-beam epitaxy and characterized them by means of transmission electron microscopy and scanning transmission electron microscopy. It was found that naturally formed vertical quantum wells, so-called lateral composition modulation (LCM), with a periodicity of ∼1 nm are formed in TlInGaAsN layers. We discuss their formation process using a simple kinetic Ising model for layer-by-layer growth, and point out that the formation of ultrashort-period LCM is a universal phenomenon in most of epitaxially grown III-V semiconductor alloys.

Self-diffusion in 69Ga121Sb/71Ga123Sb isotope heterostructures

OpenAIRE

Bracht, H.; Nicols, S. P.; Haller, E. E.; Silveira, Juan Pedro; Briones Fernández-Pola, Fernando

2001-01-01

Gallium and antimony self-diffusion experiments have been performed in undoped 69Ga121Sb/71Ga123Sb isotope heterostructures at temperatures between 571 and 708 °C under Sb- and Ga-rich ambients. Ga and Sb profiles measured with secondary ion mass spectrometry reveal that Ga diffuses faster than Sb by several orders of magnitude. This strongly suggests that the two self-atom species diffuse independently on their own sublattices. Experimental results lead us to conclude that Ga and Sb diffusio...

Sb(III) and Sb(V) separation and analytical speciation by a continuous tandem on-line separation device in connection with inductively coupled plasma atomic emission spectrometry

Energy Technology Data Exchange (ETDEWEB)

Menendez Garcia, A. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Perez Rodriguez, M.C. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Sanchez Uria, J.F. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Sanz-Medel, A. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.

1995-09-01

A sensitive, precise and automated non-chromatographic method for Sb(III) and Sb(V) analytical speciation based on a continuous tandem on-line separation device in connection with inductively coupled plasma-atomic emission (ICP-AES) detection is proposed. Two on-line successive separation steps are included into this method: a continuous liquid-liquid extraction of Sb(III) with ammonium pyrrolidine dithiocarbamate (APDC) into methylisobuthylketone (MIBK), followed by direct stibine generation from the organic phase. Both separation steps are carried out in a continuous mode and on-line with the ICP-AES detector. Optimization of experimental conditions for the tandem separation and ICP-AES detection are investigated in detail. Detection limits for Sb(III) were 3 ng.mL{sup -1} and for Sb(V) 8 ng.mL{sup -1}. Precisions observed are in the range {+-} 5%. The proposed methodology has been applied to Sb(III) and Sb(V) speciation in sea-water samples. (orig.)

TL glow ratios at different temperature intervals of integration in thermoluminescence method. Comparison of Japanese standard (MHLW notified) method with CEN standard methods

International Nuclear Information System (INIS)

Todoriki, Setsuko; Saito, Kimie; Tsujimoto, Yuka

2008-01-01

The effect of the integration temperature intervals of TL intensities on the TL glow ratio was examined in comparison of the notified method of the Ministry of Health, Labour and Welfare (MHLW method) with EN1788. Two kinds of un-irradiated geological standard rock and three kinds of spices (black pepper, turmeric, and oregano) irradiated at 0.3 kGy or 1.0 kGy were subjected to TL analysis. Although the TL glow ratio exceeded 0.1 in the andesite according to the calculation of the MHLW notified method (integration interval; 70-490degC), the maximum of the first glow were observed at 300degC or more, attributed the influence of the natural radioactivity and distinguished from food irradiation. When the integration interval was set to 166-227degC according to EN1788, the TL glow ratios became remarkably smaller than 0.1, and the evaluation of the un-irradiated sample became more clear. For spices, the TL glow ratios by the MHLW notified method fell below 0.1 in un-irradiated samples and exceeded 0.1 in irradiated ones. Moreover, Glow1 maximum temperatures of the irradiated samples were observed at the range of 168-196degC, and those of un-irradiated samples were 258degC or more. Therefore, all samples were correctly judged by the criteria of the MHLW method. However, based on the temperature range of integration defined by EN1788, the TL glow ratio of un-irradiated samples remarkably became small compared with that of the MHLW method, and the discrimination of the irradiated sample from non-irradiation sample became clearer. (author)

NaI(Tl) response functions

International Nuclear Information System (INIS)

Vega C, H. R.; Ortiz R, J. M.; Benites R, J. L.; De Leon M, H. A.

2015-09-01

The response functions of a NaI(Tl) detector have been estimated using Monte Carlo methods. Response functions were calculated for monoenergetic photon sources (0.05 to 3 MeV). Responses were calculated for point-like sources and for sources distributed in Portland cement cylinders. The responses were used to calculate the efficiency functions in term of photon energy. Commonly, sources used for calibration are point-like, and eventually sources to be measured have different features. In order to use the calibrated sources corrections due to solid angle, self-absorption and scattering, must be carried out. However, some of these corrections are not easy to perform. In this work, the calculated responses were used to estimate the detector efficiency of point-like sources, and sources distributed in Portland type cement. Samples of Portland paste were prepared and were exposed to photoneutrons produced by a 15 MV linac. Some of the elements in the cement were activated producing γ-emitting radionuclides that were measured with a NaI(Tl) gamma-ray spectrometer, that was calibrated with point-like sources. In order to determine the specific activity in the induced radioisotopes calculated efficiencies were used to make corrections due to the differences between the solid angle, photon absorption and photon scattering in the point-like calibration sources and the sources distributed in cement. During the interaction between photoneutrons and the cement samples three radioisotopes were induced: 56 Mn, 24 Na, and 28 Al. (Author)

NaI(Tl) response functions

Energy Technology Data Exchange (ETDEWEB)

Vega C, H. R.; Ortiz R, J. M. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico); Benites R, J. L. [Centro Estatal de Cancerologia de Nayarit, Calz. de la Cruz 118 Sur, Tepic, Nayarit (Mexico); De Leon M, H. A., E-mail: fermineutron@yahoo.com.mx [Instituto Tecnologico de Aguascalientes, Av. Adolfo Lopez Mateos 1801 Ote., 20155 Aguascalientes, Ags. (Mexico)

2015-09-15

The response functions of a NaI(Tl) detector have been estimated using Monte Carlo methods. Response functions were calculated for monoenergetic photon sources (0.05 to 3 MeV). Responses were calculated for point-like sources and for sources distributed in Portland cement cylinders. The responses were used to calculate the efficiency functions in term of photon energy. Commonly, sources used for calibration are point-like, and eventually sources to be measured have different features. In order to use the calibrated sources corrections due to solid angle, self-absorption and scattering, must be carried out. However, some of these corrections are not easy to perform. In this work, the calculated responses were used to estimate the detector efficiency of point-like sources, and sources distributed in Portland type cement. Samples of Portland paste were prepared and were exposed to photoneutrons produced by a 15 MV linac. Some of the elements in the cement were activated producing γ-emitting radionuclides that were measured with a NaI(Tl) gamma-ray spectrometer, that was calibrated with point-like sources. In order to determine the specific activity in the induced radioisotopes calculated efficiencies were used to make corrections due to the differences between the solid angle, photon absorption and photon scattering in the point-like calibration sources and the sources distributed in cement. During the interaction between photoneutrons and the cement samples three radioisotopes were induced: {sup 56}Mn, {sup 24}Na, and {sup 28}Al. (Author)

Novel laser-processed CsI:Tl detector for SPECT

Energy Technology Data Exchange (ETDEWEB)

Sabet, H., E-mail: hsabet@mgh.harvard.edu; Uzun-Ozsahin, D.; El-Fakhri, G. [Massachusetts General Hospital, Harvard Medical School, Boston, Massachusetts 02129 (United States); Bläckberg, L. [Massachusetts General Hospital, Harvard Medical School, Boston, Massachusetts 02129 and Department of Physics and Astronomy, Uppsala University, Uppsala 75120 (Sweden)

2016-05-15

Purpose: The aim of this work is to demonstrate the feasibility of a novel technique for fabrication of high spatial resolution CsI:Tl scintillation detectors for single photon emission computed tomography systems. Methods: The scintillators are fabricated using laser-induced optical barriers technique to create optical microstructures (or optical barriers) inside the CsI:Tl crystal bulk. The laser-processed CsI:Tl crystals are 3, 5, and 10 mm in thickness. In this work, the authors focus on the simplest pattern of optical barriers in that the barriers are created in the crystal bulk to form pixel-like patterns resembling mechanically pixelated scintillators. The monolithic CsI:Tl scintillator samples are fabricated with optical barrier patterns with 1.0 × 1.0 mm{sup 2} and 0.625 × 0.625 mm{sup 2} pixels. Experiments were conducted to characterize the fabricated arrays in terms of pixel separation and energy resolution. A 4 × 4 array of multipixel photon counter was used to collect the scintillation light in all the experiments. Results: The process yield for fabricating the CsI:Tl arrays is 100% with processing time under 50 min. From the flood maps of the fabricated detectors exposed to 122 keV gammas, peak-to-valley (P/V) ratios of greater than 2.3 are calculated. The P/V values suggest that regardless of the crystal thickness, the pixels can be resolved. Conclusions: The results suggest that optical barriers can be considered as a robust alternative to mechanically pixelated arrays and can provide high spatial resolution while maintaining the sensitivity in a high-throughput and cost-effective manner.

Novel laser-processed CsI:Tl detector for SPECT

International Nuclear Information System (INIS)

Sabet, H.; Uzun-Ozsahin, D.; El-Fakhri, G.; Bläckberg, L.

2016-01-01

Purpose: The aim of this work is to demonstrate the feasibility of a novel technique for fabrication of high spatial resolution CsI:Tl scintillation detectors for single photon emission computed tomography systems. Methods: The scintillators are fabricated using laser-induced optical barriers technique to create optical microstructures (or optical barriers) inside the CsI:Tl crystal bulk. The laser-processed CsI:Tl crystals are 3, 5, and 10 mm in thickness. In this work, the authors focus on the simplest pattern of optical barriers in that the barriers are created in the crystal bulk to form pixel-like patterns resembling mechanically pixelated scintillators. The monolithic CsI:Tl scintillator samples are fabricated with optical barrier patterns with 1.0 × 1.0 mm"2 and 0.625 × 0.625 mm"2 pixels. Experiments were conducted to characterize the fabricated arrays in terms of pixel separation and energy resolution. A 4 × 4 array of multipixel photon counter was used to collect the scintillation light in all the experiments. Results: The process yield for fabricating the CsI:Tl arrays is 100% with processing time under 50 min. From the flood maps of the fabricated detectors exposed to 122 keV gammas, peak-to-valley (P/V) ratios of greater than 2.3 are calculated. The P/V values suggest that regardless of the crystal thickness, the pixels can be resolved. Conclusions: The results suggest that optical barriers can be considered as a robust alternative to mechanically pixelated arrays and can provide high spatial resolution while maintaining the sensitivity in a high-throughput and cost-effective manner.

Density functional simulations of Sb-rich GeSbTe phase change alloys

OpenAIRE

Gabardi, S; Caravati, S; Bernasconi, M; Parrinello, M

2012-01-01

We generated models of the amorphous phase of Sb rich GeSbTe phase change alloys by quenching from the melt within density functional molecular dynamics. We considered the two compositions Ge 1Sb 1Te 1 and Ge 2Sb 4Te 5. Comparison with previous results on the most studied Ge 2Sb 2Te 5 allowed us to draw some conclusions on the dependence of the structural properties of the amorphous phase on the alloy composition. Vibrational and electronic properties were also scrutinized. Phonons at high fr...

Characterization of cartilaginous tumors with 201Tl scintigraphy

International Nuclear Information System (INIS)

Higuchi, Takahiro; Taki, Junichi; Sumiya, Hisashi; Kinuya, Seigo; Nakajima, Kenichi; Tonami, Norihisa

2005-01-01

Histological diagnosis and grading of cartilaginous tumors are closely correlated with patient prognosis; consequently, they are essential elements. We attempted to clarify the characteristics of 201 Tl uptake in various histological types of cartilaginous tumors and to assess its clinical value. Twenty-two cases with histologically proven cartilaginous tumors (3 enchondromas, 15 conventional chondrosarcomas (grade I=9, II=5, III=1), 3 mesenchymal chondrosarcomas, and 1 de-differentiated chondrosarcoma) were examined retrospectively. Planar 201 Tl images were recorded 15 mm following intravenous injection of 201 Tl (111 MBq). 201 Tl uptake in the tumor was evaluated visually employing a five-grade scoring system: 0=no appreciable uptake, 1=faint uptake above the background level, 2=moderate uptake, 3=intense uptake but lower than heart uptake and 4=uptake higher than heart uptake. 201 Tl uptake scores were 0 in 3 of 3 enchondromas, 9 of 9 grade I, and 4 of 5 grade II conventional chondrosarcomas. 201 Tl uptake scores were 1 among 1 of 5 grades II and a grade III conventional chondrosarcoma. Mesenchymal chondrosarcoma and de-differentiated chondrosarcoma displayed 201 Tl uptake scores of 2 or 3. Absence of elevated 201 Tl uptake in cartilaginous tumors was indicative of enchondroma or low-grade conventional chondrosarcoma. However, in instances in which 201 Tl uptake is obvious, high-grade chondrosarcoma or variant types should be considered. (author)

Phytotoxicity of thallium (Tl) in culture solution. Pt. 1. Effects of Tl(I) on the growth and heavy metal contents of pea and field bean plants

Energy Technology Data Exchange (ETDEWEB)

Poetsch, U; Austenfeld, F A

1985-01-01

The effects of TlNO/sub 3/ and Tl(I)EDTA on growth and heavy metal contents of pea plants and field bean plants were compared in hydroponic culture experiments. In the presence of TlNO/sub 3/, the essential heavy metals were available to the plants in their ionic forms. When Tl(I)EDTA was present the essential heavy metals were available as chelated complexes. With increasing concentration of TlNO/sub 3/ dry matter production of pea plants was lowered and the Tl content of each organ was increased. The highest Tl content was found within the stems. The increased Tl contents were accompanied by depressed Mn, Zn, and Cu contents of the roots and depressed Mn contents of the stems, but increased Fe contents of the stems. Substitution of TlNO/sub 3/ by Tl(I)EDTA resulted in a stronger growth inhibition of the pea plants, and higher Tl contents of each organ. The highest Tl content was found within the stems. Tl(I)EDTA depressed Mn in the roots, but increased Fe and Mn in the stems, and Fe, Zn and Cu in the leaves. The increases may due to concentration by growth inhibition. The growth of the field bean was not effected by TlNO/sub 3/ nor by Tl(I)EDTA. The field bean contained most of the Tl within the roots and translocated only relatively small amounts to the shoots. This pattern was independent of the Tl compound. Increasing concentrations of TlNO/sub 3/ resulted in depressed Mn and Zn contents of the roots, and Mn contents of the stems. Chelation of Tl(I) resulted in a decrease of the Tl content of each organ. Tl(I)EDTA depressed only the Mn content of the roots.

Defect Structure of High-Temperature-Grown GaMnSb/GaSb

International Nuclear Information System (INIS)

Romanowski, P.; Bak-Misiuk, J.; Dynowska, E.; Domagala, J.Z.; Wojciechowski, T.; Jakiela, R.; Sadowski, J.; Barcz, A.; Caliebe, W.

2010-01-01

GaMnSb/GaSb(100) layers with embedded MnSb inclusions have been grown at 720 K using MBE technique. This paper presents the investigation of the defect structure of Ga1-xMnxSb layers with different content of manganese (up to x = 0.07). X-ray diffraction method using conventional and synchrotron radiation was applied. Dimensions and shapes of inclusions were detected by scanning electron microscopy. Depth profiles of elements were measured using secondary ion mass spectroscopy technique. (authors)

Principles of Good Practice in SoTL

Science.gov (United States)

Felten, Peter

2013-01-01

For the Scholarship of Teaching and Learning (SoTL) to be understood as significant intellectual work in the academy, SoTL practitioners need to identify shared principles of good practice. While honoring the diversity of SoTL in its many forms across the globe, such principles can serve as a heuristic for assessing work in our field. These…

New colour centres in KCl:(Tl+ + Ca2+) and KCl:(Tl+ + Sr2+) crystals

International Nuclear Information System (INIS)

Ioan, A.; Topa, V.; Giurgea, M.

1978-01-01

Electrolytic colouring under unusual conditions (low temperature and high voltage) gives rise to the appearance of three new absorption bands peaking at 3.2, 2.5, and 1.7 eV and at 2.8, 2.1, and 1.5 eV in KCl:(Tl + + Ca 2+ ) and in KCl:(Tl + + Sr 2+ ) single crystals, respectively. The modifications of the absorption spectra of the coloured crystals induced by the application of a reversed electric field at the colouring temperature or by heat treatment are investigated. It is likely that the colour centre responsible for the new absorption bands is an aggregate centre which, besides an Tl - -complex, contains also at least an Ca(Sr) ion, a trapped electron, and an anionic vacancy. (author)

Probing the distribution and contamination levels of 10 trace metal/metalloids in soils near a Pb/Zn smelter in Middle China.

Science.gov (United States)

Li, Zhonggen; Feng, Xinbin; Bi, Xiangyang; Li, Guanghui; Lin, Yan; Sun, Guangyi

2014-03-01

The horizontal and vertical distribution patterns and contamination status of ten trace metal/metalloids (Ag, Bi, Co, Cr, Ge, In, Ni, Sb, Sn, Tl) in soils around one of the largest Chinese Pb-Zn smelter in Zhuzhou City, Central China, were revealed. Different soil samples were collected from 11 areas, including ten agricultural areas and one city park area, with a total of 83 surface soil samples and six soil cores obtained. Trace metal/metalloids were determined by inductively coupled plasma-mass spectrometry after digestion by an acid mixture of HF and HNO3. The results showed that Ag, Bi, In, Sb, Sn, and Tl contents decreased both with the distance to the Pb-Zn smelter as well as the soil depth, hinting that these elements were mainly originated from the Pb-Zn smelting operations and were introduced into soils through atmospheric deposition. Soil Ge was influenced by the smelter at a less extent, while the distributions of Co, Cr, and Ni were roughly even among most sampling sites and soil depths, suggesting that they were primarily derived from natural sources. The contamination status, as revealed by the geo-accumulation index (I geo), indicated that In and Ag were the most enriched elements, followed by Sb, Bi, and Sn. In general, Cr, Tl, Co, Ni, and Ge were of an uncontaminated status.

Deformation effects in electronic spectra of the layered semiconductors TlGaS sub 2 , TlGaSe sub 2 and TlInS sub 2

CERN Document Server

Allakhverdiev, K R; Suleymanov, R A; Gasanov, N Z

2003-01-01

The deformation effects in electronic spectra of the ternary layered semiconductors TlGaS sub 2 , TlGaSe sub 2 and TlInS sub 2 are considered. It is shown that the influence of hydrostatic pressure, thermal expansion and variation of composition in solid solutions on the band gap of the crystals investigated can be described in the framework of one common model of deformation potentials. This model appears to be close to that of layered semiconductors of the A sub 3 B sub 6 group, attesting to the fact that the main principles of formation of band structure in these two groups of layered crystals are the same.

TL and OSL dosimetric properties of Opal gemstone for gamma radiation dosimetry

International Nuclear Information System (INIS)

Antonio, Patrícia L.; Gronchi, Claudia C.; Oliveira, Raquel A.P.; Khoury, Helen J.; Caldas, Linda V.E.

2016-01-01

In this work, the response of the natural material Opal was studied in relation to its thermoluminescence (TL) and optically stimulated luminescence (OSL), after exposure to the gamma radiation of a "6"0Co source. The structure of the powdered Opal was verified using the X-ray diffraction, scanning electronic microscopy and energy-dispersive X-ray spectroscopy techniques. The material, in its stone form, was turned into powder and mixed to Teflon (also in powder) in three different concentrations, and then pellets were manufactured. The aim of this work was to evaluate the response of these pellets in high-doses of gamma radiation beams, and to observe their possible application as dosimeters, using the TL and OSL techniques. The dosimetric properties of the samples were analyzed by means of different tests, as: TL emission curves and OSL signal decay curves, reproducibility of TL and OSL response, minimum detectable dose, TL and OSL dose–response curves (5 Gy–10 kGy), and fading. The results obtained in this work, for the TL and OSL phenomena, demonstrated that the pellets of Opal + Teflon present an adequate performance e possibility of use as dosimeters in beams of high-dose gamma radiation. - Highlights: • The XRD, SEM and EDX techniques were used to investigate powdered Opal. • Pellets of three different concentrations of Opal and Teflon were studied. • The dosimetric properties of the Opal + Teflon pellets were verified. • TL and OSL techniques were used to analyze the characteristics of the pellets. • Pellets of concentration of 2:1 (Opal:Teflon) presented the most adequate results.

Sequential and simultaneous adsorption of Sb(III) and Sb(V) on ferrihydrite: Implications for oxidation and competition.

Science.gov (United States)

Qi, Pengfei; Pichler, Thomas

2016-02-01

Antimony (Sb) is a naturally occurring element of growing environmental concern whose toxicity, adsorption behavior and other chemical properties are similar to that of arsenic (As). However, less is known about Sb compared to As. Individual and simultaneous adsorption experiments with Sb(III) and Sb(V) were conducted in batch mode with focus on the Sb speciation of the remaining liquid phase during individual Sb(III) adsorption experiments. The simultaneous adsorption and oxidation of Sb(III) was confirmed by the appearance of Sb(V) in the solution at varying Fe/Sb ratios (500, 100 and 8) and varying pH values (3.8, 7 and 9). This newly formed Sb(V) was subsequently removed from solution at a Fe/Sb ratio of 500 or at a pH of 3.8. However, more or less only Sb(V) was observed in the liquid phase at the end of the experiments at lower Fe/Sb ratios and higher pH, indicating that competition took place between the newly formed Sb(V) and Sb(III), and that Sb(III) outcompeted Sb(V). This was independently confirmed by simultaneous adsorption experiments of Sb(III) and Sb(V) in binary systems. Under such conditions, the presence of Sb(V) had no influence on the adsorption of Sb(III) while Sb(V) adsorption was significantly inhibited by Sb(III) over a wide pH range (4-10). Thus, in the presence of ferrihydrite and under redox conditions, which allow the presence of both Sb species, Sb(V) should be the dominant species in aquatic environments, since Sb(III) is adsorbed preferentially and at the same time oxidized to Sb(V). Copyright © 2015 Elsevier Ltd. All rights reserved.

Investigation of the thermal stability of 210 deg. C TL peak of quartz and dating the components of terrazzo from the monastery church of Tegernsee

International Nuclear Information System (INIS)

Goeksu, H.Y.; Schwenk, P.; Semiochkina, N.

2001-01-01

The lifetime of the thermoluminescence (TL) peak of quartz observed at 210 deg. C using 5 deg. C/s heating rate is assessed using well-dated thermally isolated bricks from a monastery and exposed bricks from warmer climatic zones by comparing the absorbed dose obtained using the 210 deg. C TL peak with those obtained from 310 deg. C TL peak. The lifetimes of the 210 deg. C TL peak calculated for samples collected from thermally isolated excavations and exposed buildings are found to be clustered around 8000-10000 and 600-800 years, respectively. The results proved that 210 deg. C TL peak could be used for dating of samples younger than 1000 years without thermal correction if the samples are thermally isolated from their environment. TL ages are obtained using quartz, polyminerals from brick pieces as well as flint splinters, and other quartz inclusions extracted from the mortar of the terrazzo floor of the monastery church. The measured TL ages and the consistency of the results are discussed. The fine grains in the mortar, which contained calcite/aragonite, could not be dated using thermoluminescence due to presence of a very strong non-radiation induced TL glow

Positron annihilation studies of high dose Sb implanted silicon

International Nuclear Information System (INIS)

Schut, H.; Eijt, S.W.H.; Beling, C.D.; Ho, K.; Takamura, Y.

2005-01-01

The formation and evolution of vacancies and precipitates created by implantation of 60 keV, 2 x 10 16 cm -2 Sb + in pre-amorphized (0 0 1) Cz-Si is studied using the Doppler broadening (DB) and two-dimensional angular correlation of annihilation radiation (2D-ACAR) positron beam techniques. After implantation, samples were laser annealed (LTA) and subsequently thermal annealed at temperatures ranging from 400 to 1000 deg. C. Implantation-induced vacancy-type defects were detected up to a depth of 280 nm. After LTA, positron annihilation related to both Sb and remaining defects is observed in the first 100 nm below the surface. The deeper region only shows positron trapping at vacancy-type defects with strong reduced concentration. Complete removal is obtained after 600 deg. C anneal. At this temperature, the positron data for the upper region reveals trapping at Sb and Si sites only. With increasing annealing time (at 600 deg. C) or increasing temperature (up to 1000 deg. C) positron annihilation at Sb-sites associated with neighboring vacancies becomes apparent. Results are correlated with the observed Sb electrical deactivation above 600 deg. C, the shift from small Sb aggregates to precipitates and out-diffusion of Sb from the implantation region at higher temperatures

Redundant Sb condensation on GaSb epilayers grown by molecular beam epitaxy during cooling procedure

International Nuclear Information System (INIS)

Arpapay, B.; Şahin, S.; Arıkan, B.; Serincan, U.

2014-01-01

The effect of four different cooling receipts on the surface morphologies of unintentionally-doped GaSb epilayers on GaSb (100) substrates grown by molecular beam epitaxy is reported. Those receipts include three different Sb beam equivalent pressure (BEP) levels and two different termination temperatures. Surface morphologies of epilayers were examined by wet etching, surface profiler, atomic force microscopy, scanning electron microscopy and Raman spectroscopy. The results demonstrate that during the cooling period, a Sb BEP of 4.00 × 10 −4 Pa at a termination temperature of 400 °C induces a smooth surface without Sb condensation whereas same Sb BEP at a termination temperature of 350 °C forms a 300 nm thick Sb layer on the surface. In addition, it is revealed that by applying a wet etching procedure and using a surface profiler it is possible to identify this condensed layer from the two-sloped feature of mesa profile. - Highlights: • Sb beam flux termination temperature is crucial for redundant Sb condensation. • Sb beam flux level has a role on the thickness of redundant condensed Sb layer. • Redundant Sb layer thickness can be measured by two-sloped mesa structure

$\\alpha$-decay study of $^{182,184}$Tl

CERN Document Server

Van Beveren, C; Barzakh, A E; Cocolios, T E; de Groote, R P; Fedorov, D; Fedosseev, V N; Ferrer, R; Ghys, L; Huyse, M; Köster, U; Lane, J; Liberati, V; Lynch, K M; Marsh, B A; Molkanov, P L; Procter, T J; Rapisarda, E; Sandhu, K; Seliverstov, M D; Van Duppen, P; Venhart, M; Veselský, M

2016-01-01

α -decay spectroscopy of 182,184 Tl has been performed at the CERN isotope separator on-line ( ISOLDE ) facility. New fi ne-structure α decays have been observed for both isotopes. α -decay branching ratios of 0.089 ( 19 ) %, 0.047 ( 6 ) % and 1.22 ( 30 ) % have been deduced for the ( 10 − ) , ( 7 + ) and ( 2 − ) states respectively in 184 Tl and a lower limit of 0.49% for the α -decay branching ratio of 182 Tl. A new half-life of 9.5 ( 2 ) s for the ( 2 − ) state in 184 Tl and 1.9 ( 1 ) s for the low-spin state in 182 Tl has been deduced. Using α – γ coincidence analysis, multiple γ rays were observed de-exciting levels in 178,18 0 Au fed by 182,184 Tl α decays. The γ transitions connecting these low-lying states in 178,18 0 Au are essential to sort the data and possibly identify bands from in- beam studies in these isotopes. Owing to the complex fi ne-structure α decays and limited knowledge about the structure of the daughter nuclei, only partial level schemes could be constructed for bot...

Hole-dominated transport in InSb nanowires grown on high-quality InSb films

Energy Technology Data Exchange (ETDEWEB)

Algarni, Zaina; George, David; Singh, Abhay; Lin, Yuankun; Philipose, U., E-mail: usha.philipose@unt.edu [University of North Texas, Department of Physics (United States)

2016-12-15

We have developed an effective strategy for synthesizing p-type indium antimonide (InSb) nanowires on a thin film of InSb grown on glass substrate. The InSb films were grown by a chemical reaction between Sb{sub 2}S{sub 3} and In and were characterized by structural, compositional, and optical studies. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies reveal that the surface of the substrate is covered with a polycrystalline InSb film comprised of sub-micron sized InSb islands. Energy dispersive X-ray (EDX) results show that the film is stoichiometric InSb. The optical constants of the InSb film, characterized using a variable-angle spectroscopic ellipsometer (VASE) shows a maximum value for refractive index at 3.7 near 1.8 eV, and the extinction coefficient (k) shows a maximum value 3.3 near 4.1 eV. InSb nanowires were subsequently grown on the InSb film with 20 nm sized Au nanoparticles functioning as the metal catalyst initiating nanowire growth. The InSb nanowires with diameters in the range of 40–60 nm exhibit good crystallinity and were found to be rich in Sb. High concentrations of anions in binary semiconductors are known to introduce acceptor levels within the band gap. This un-intentional doping of the InSb nanowire resulting in hole-dominated transport in the nanowires is demonstrated by the fabrication of a p-channel nanowire field effect transistor. The hole concentration and field effect mobility are estimated to be ≈1.3 × 10{sup 17} cm{sup −3} and 1000 cm{sup 2} V{sup −1} s{sup −1}, respectively, at room temperature, values that are particularly attractive for the technological implications of utilizing p-InSb nanowires in CMOS electronics.

Phytotoxicity of thallium (Tl) in culture solution. Pt. 2. Effects of Tl(III) on the growth and heavy metal contents of pea and field bean plants

Energy Technology Data Exchange (ETDEWEB)

Pieper, B; Austenfeld, F A

1985-01-01

The effects of Tl(NO/sub 3/)/sub 3/ and Tl(III)EDTA on growth and heavy metal contents of pea plants and field bean plants were compared in hydroponic culture experiments. In the presence of Tl(NO/sub 3/)/sub 3/, the essential heavy metals were available to the plants in their ionic forms. When Tl(III)EDTA was present the essential heavy metals were available as chelated complexes. Dry matter production of the pea plants was inhibited to a greater extent by Tl(III)EDTA than by Tl(NO/sub 3/)/sub 3/. The distribution of Tl within the plant was unaffected by the accompanying anion, however an increase of the Tl content of the stems and the leaves was observed in the presence of Tl(III)EDTA. The micronutrients exhibited different interactions with Tl(III). In the presence of increasing concentrations of Tl(NO/sub 3/)/sub 3/ the Mn content of each organ and the Zn content of the roots were lowered, but the Zn content of the stems was increased. Increasing concentrations of Tl(III)EDTA resulted only in a decrease of the Mn content of the roots, but in an increase of the contents of Fe and Mn within the stems, and Fe, Mn, Zn, and Cu within the leaves. The increases may be due to concentration by growth inhibition. In contrast to pea plants, growth of field bean plants was inhibited only by Tl(NO/sub 3/)/sub 3/. The field bean plants retained most of the Tl within the roots independent of the Tl compound in the solution. Chelation of Tl(III) resulted in higher Tl contents of both the roots and the stems, but equal or reduced Tl contents of the leaves. Whereas increasing concentrations of Tl(NO/sub 3/)/sub 3/ reduced the Mn content of each organ as well as the Zn content of the roots and the leaves, Tl(III)EDTA only reduced the Mn content of the roots.

Zr3NiSb7: a new antimony-enriched ZrSb2 derivative

Directory of Open Access Journals (Sweden)

V. Romaka

2008-08-01

Full Text Available Single crystals of trizirconium nickel heptaantimonide were synthesized from the constituent elements by arc-melting. The compound crystallizes in a unique structure type and belongs to the family of two-layer structures. All crystallographically unique atoms (3 × Zr, 1 × Ni and 7 × Sb are located at sites with m symmetry. The structure contains `Zr2Ni2Sb5' and `Zr4Sb9' fragments and might be described as a new ZrSb2 derivative with a high Sb content.

Thermoelectric Properties of SnO2 Ceramics Doped with Sb and Zn

DEFF Research Database (Denmark)

Yanagiya, S.; Van Nong, Ngo; Xu, Jianxiao Jackie

2011-01-01

Polycrystalline SnO2-based samples (Sn0.97−x Sb0.03Zn x O2, x = 0, 0.01, 0.03) were prepared by solid-state reactions. The thermoelectric properties of SnO2 doped with Sb and Zn were investigated from 300 K to 1100 K. X-ray diffraction (XRD) analysis revealed all XRD peaks of all the samples...

Effect of particle size in the TL response of natural quartz sensitized by high dose of gamma radiation and heat-treatments

Directory of Open Access Journals (Sweden)

Álvaro Barbosa de Carvalho Jr

2010-06-01

Full Text Available This work investigates the effect of particle size in the thermoluminescence (TL response of a quartz crystal that was initially crushed and classified into ten size fractions between 38 μm and 5 mm. Aliquots of each size fraction were sensitized with a dose of 25 kGy of γ rays and heat-treatments at 400 °C. TL glow curves of sensitized and non-sensitized samples were recorded as a function of different test-doses of γ rays. For the non-sensitized samples, the TL peak near 325 °C increases with the decrease in particle size. In the case of sensitized samples, a strong TL peak near 300 °C increases with the increase in particle size up to mean grain size equal to 304 μm. Above 304 μm, an abrupt reduction in the TL intensity is noticed for the sensitized peak. These effects are discussed in relation to the specific surface area of quartz particles and the intensity of the electron paramagnetic resonance signal of the E'1 center induced by the sensitization process.

Lower lattice thermal conductivity in SbAs than As or Sb monolayers: a first-principles study.

Science.gov (United States)

Guo, San-Dong; Liu, Jiang-Tao

2017-12-06

Phonon transport in group-VA element (As, Sb and Bi) monolayer semiconductors has been widely investigated in theory, and, of them, monolayer Sb (antimonene) has recently been synthesized. In this work, phonon transport in monolayer SbAs is investigated with a combination of first-principles calculations and the linearized phonon Boltzmann equation. It is found that the lattice thermal conductivity of monolayer SbAs is lower than those of both monolayer As and Sb, and the corresponding sheet thermal conductance is 28.8 W K -1 at room temperature. To understand the lower lattice thermal conductivity in monolayer SbAs than those in monolayer As and Sb, the group velocities and phonon lifetimes of monolayer As, SbAs and Sb are calculated. The calculated results show that the group velocities of monolayer SbAs are between those of monolayer As and Sb, but that the phonon lifetimes of SbAs are smaller than those of both monolayer As and Sb. Hence, the low lattice thermal conductivity in monolayer SbAs is attributed to very small phonon lifetimes. Unexpectedly, the ZA branch has very little contribution to the total thermal conductivity, only 2.4%, which is obviously different from those of monolayer As and Sb with very large contributions. This can be explained by very small phonon lifetimes for the ZA branch of monolayer SbAs. The lower lattice thermal conductivity of monolayer SbAs compared to that of monolayer As or Sb can be understood by the alloying of As (Sb) with Sb (As), which should introduce phonon point defect scattering. We also consider the isotope and size effects on the lattice thermal conductivity. It is found that isotope scattering produces a neglectful effect, and the lattice thermal conductivity with a characteristic length smaller than 30 nm can reach a decrease of about 47%. These results may offer perspectives on tuning the lattice thermal conductivity by the mixture of multiple elements for applications of thermal management and

Influence of low-temperature annealing on InSb properties

International Nuclear Information System (INIS)

Tsitsina, N.P.; Fadeeva, A.P.; Vdovkina, E.E.; Baryshev, N.S.; Aver'yanov, I.S.

1975-01-01

Annealing at 200 deg C during 6 days does not cause inversion of conductivity in n-InSb, leads to the increase of the carrier concentration and the decrease of the specific resistance in samples both of n- and of p-type; these variations being more significant in the material of n-type. The existence of a level at a distance of 0.15-0.17 eV from the ceiling of the valency zone in non-annealed samples of InSb is confirmed. The level is of acceptor type and disappears with low-temperature annealing. The low-temperature annealing practically does not influence the lifetime in p-type samples and results in the 5-20-fold increase in the lifetime in n-type samples

Tetrahedral 1B4Sb nanoclusters in GaP:(B, Sb)

Energy Technology Data Exchange (ETDEWEB)

Elyukhin, V A, E-mail: elyukhin@cinvestav.m [Departamento de Ingenieria Electrica-SEES, CINVESTAV-IPN, Avenida IPN 2508, Col. San Pedro Zacatenco, C. P. 07360, Mexico, D. F. (Mexico)

2009-05-01

Self-assembling conditions of 1B4Sb tetrahedral nanoclusters in GaP doped with boron and Sb isoelectronic impurities are represented in the ultradilute and dilute limits of the boron and Sb contents, respectively. The fulfilled estimates demonstrated the preferential complete or almost complete allocation of boron atoms in 1B4Sb nanoclusters at temperatures of 500 {sup 0}C and 900 {sup 0}C, respectively. The significant decrease of the sum of the free energies of the constituent compounds is the main origin of self-assembling. The reduction of the strain energy is the additional cause of this phenomenon.

Distribution, speciation and availability of antimony (Sb) in soils and terrestrial plants from an active Sb mining area

International Nuclear Information System (INIS)

Okkenhaug, Gudny; Zhu Yongguan; Luo Lei; Lei Ming; Li Xi; Mulder, Jan

2011-01-01

Here, we present one of the first studies investigating the mobility, solubility and the speciation-dependent in-situ bioaccumulation of antimony (Sb) in an active Sb mining area (Xikuangshan, China). Total Sb concentrations in soils are high (527-11,798 mg kg -1 ), and all soils, including those taken from a paddy field and a vegetable garden, show a high bioavailable Sb fraction (6.3-748 mg kg -1 ), dominated by Sb(V). Elevated concentrations in native plant species (109-4029 mg kg -1 ) underpin this. Both chemical equilibrium studies and XANES data suggest the presence of Ca[Sb(OH) 6 ] 2 , controlling Sb solubility. A very close relationship was found between the citric acid extractable Sb in plants and water or sulfate extractable Sb in soil, indicating that citric acid extractable Sb content in plants may be a better predictor for bioavailable Sb in soil than total acid digestible Sb plant content. - Highlights: → Antimony (Sb) in soils from an active Sb mining area is highly bioavailable. → Sb occurs mainly as Sb(V) in Sb mining impacted soils and plants. → Sb solubility in Sb mining impacted soils is governed by Ca[Sb(OH) 6 ] 2 . → Citric acid extractable Sb in plants and bioavailable Sb in soils are strongly correlated. - Antimony (Sb) in soils from an active Sb mining area is highly bioavailable and controlled by the solubility of calcium antimonate.

Abnormal optical behaviour of InAsSb quantum dots grown on GaAs substrate by molecular beam epitaxy

International Nuclear Information System (INIS)

Rihani, J.; Ben Sedrine, N.; Sallet, V.; Harmand, J.C.; Oueslati, M.; Chtourou, R.

2008-01-01

InAs(Sb) quantum dots (QDs) samples were grown on GaAs (001) substrate by Molecular Beam Epitaxy (MBE). The structural characterization by Atomic Force Microscopy (AFM) of samples shows that InAsSb islands size increases strongly with antimony incorporation in InAs/GaAs QDs and decreases with reducing the growth temperature from 520 deg. C to 490 deg. C. Abnormal optical behaviour was observed in room temperature (RT) photoluminescence (PL) spectra of samples grown at high temperature (520 deg. C). Temperature dependent PL study was investigated and reveals an anomalous evolution of emission peak energy (EPE) of InAsSb islands, well-known as 'S-inverted curve' and attributed to the release of confined carriers from the InAsSb QDs ground states to the InAsSb wetting layer (WL) states. With only decreasing the growth temperature, the S-inverted shape was suppressed indicating a fulfilled 3D-confinement of carriers in the InAsSb/GaAs QD sample

Importance of controlling the Tl-oxide partial pressure throughout the processing of TlBa2CaCu2O7 thin films

International Nuclear Information System (INIS)

Siegal, M.P.; Venturini, E.L.; Newcomer, P.P.; Overmyer, D.L.; Dominguez, F.; Dunn, R.

1995-01-01

TlBa 2 CaCu 2 O 7 (Tl-1212) superconducting films 5000--6000 A thick have been grown on LaAlO 3 (100) substrates using oxide precursors in a closed two-zone thallination furnace. Tl-1212 films can be grown with transition temperatures ∼100 K, and critical current densities measured by magnetization of J cm (5 K)>10 7 A/cm 2 and J cm (77 K)>10 5 A/cm 2 . Processing conditions, substrate temperatures and Tl-oxide source temperatures are found which result in smooth, nearly phase-pure Tl-1212 films. Variations in the respective temperature ramps of the Tl-oxide zone and the substrate zone can greatly influence resulting film properties such as microstructure, morphology, superconducting transition temperature, and critical current density. copyright 1995 American Institute of Physics

Hole-dominated transport in InSb nanowires grown on high-quality InSb films

Science.gov (United States)

Algarni, Zaina; George, David; Singh, Abhay; Lin, Yuankun; Philipose, U.

2016-12-01

We have developed an effective strategy for synthesizing p-type indium antimonide (InSb) nanowires on a thin film of InSb grown on glass substrate. The InSb films were grown by a chemical reaction between S b 2 S 3 and I n and were characterized by structural, compositional, and optical studies. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies reveal that the surface of the substrate is covered with a polycrystalline InSb film comprised of sub-micron sized InSb islands. Energy dispersive X-ray (EDX) results show that the film is stoichiometric InSb. The optical constants of the InSb film, characterized using a variable-angle spectroscopic ellipsometer (VASE) shows a maximum value for refractive index at 3.7 near 1.8 eV, and the extinction coefficient (k) shows a maximum value 3.3 near 4.1 eV. InSb nanowires were subsequently grown on the InSb film with 20 nm sized Au nanoparticles functioning as the metal catalyst initiating nanowire growth. The InSb nanowires with diameters in the range of 40-60 nm exhibit good crystallinity and were found to be rich in Sb. High concentrations of anions in binary semiconductors are known to introduce acceptor levels within the band gap. This un-intentional doping of the InSb nanowire resulting in hole-dominated transport in the nanowires is demonstrated by the fabrication of a p-channel nanowire field effect transistor. The hole concentration and field effect mobility are estimated to be ≈1.3 × 1017 cm-3 and 1000 cm2 V-1 s-1, respectively, at room temperature, values that are particularly attractive for the technological implications of utilizing p-InSb nanowires in CMOS electronics.

X-ray dose response of calcite—A comprehensive analysis for optimal application in TL dosimetry

International Nuclear Information System (INIS)

Kalita, J.M.; Wary, G.

2016-01-01

Highlights: • Effect of annealing temperature on TL signal of calcite has been studied. • Specific annealing treatment for optimal dose response has been evaluated. • The dose response of natural calcite has been analyzed quantitatively. - Abstract: The effect of various annealing treatments on dosimetric characteristics of orange calcite (CaCO_3) mineral has been studied in detail. Quantitative analysis on the dose response shows that the 573 K annealed sample showed sublinear dose response from 10 mGy to 1 Gy. The fading and reproducibility of this sample are also good enough for dosimetric application. However, a specific annealing treatment after irradiation shows some significant improvements in the dosimetric characteristics of the sample. The 773 K pre-annealed sample, after X-ray irradiation post-annealing at 340 K for 6 min provides linear dose response from 10 mGy to 3.60 Gy, very less fading and good reproducibility. Moreover, this sample after post-annealing at 380 K for 6 min shows linear dose response from 10 mGy to 5.40 Gy when analyzed from the ∼408 K thermoluminescence (TL) glow peak. Analysis of TL glow curves confirmed that the 1.30 eV trap center in calcite crystal is the most effective trapping site for dosimetric application.

X-ray dose response of calcite—A comprehensive analysis for optimal application in TL dosimetry

Energy Technology Data Exchange (ETDEWEB)

Kalita, J.M., E-mail: jitukalita09@gmail.com; Wary, G.

2016-09-15

Highlights: • Effect of annealing temperature on TL signal of calcite has been studied. • Specific annealing treatment for optimal dose response has been evaluated. • The dose response of natural calcite has been analyzed quantitatively. - Abstract: The effect of various annealing treatments on dosimetric characteristics of orange calcite (CaCO{sub 3}) mineral has been studied in detail. Quantitative analysis on the dose response shows that the 573 K annealed sample showed sublinear dose response from 10 mGy to 1 Gy. The fading and reproducibility of this sample are also good enough for dosimetric application. However, a specific annealing treatment after irradiation shows some significant improvements in the dosimetric characteristics of the sample. The 773 K pre-annealed sample, after X-ray irradiation post-annealing at 340 K for 6 min provides linear dose response from 10 mGy to 3.60 Gy, very less fading and good reproducibility. Moreover, this sample after post-annealing at 380 K for 6 min shows linear dose response from 10 mGy to 5.40 Gy when analyzed from the ∼408 K thermoluminescence (TL) glow peak. Analysis of TL glow curves confirmed that the 1.30 eV trap center in calcite crystal is the most effective trapping site for dosimetric application.

Preparation of 199Tl and its labelled compound

International Nuclear Information System (INIS)

Zhou Dehai; Guan Changtian; Kuang Anren

1991-10-01

Usually, 199 Ti is obtained by the nuclear reaction of 197 Au(α, 2n) 199 Tl. A gold target with 50±0.1 mm in diameter, 0.8 mm in thickness and 99.99% in purity was mounted in a cyclotron beam line. The target was bombarded by α particles with the energy of 25∼27 MeV and the beam current of 15∼20μA. The irradiated gold target was dissolved by aqua regia. Then the saturated aqueous solution of SO 2 was added. The 199 Tl(III)reduced to 199 Tl(I). The deposit of gold was removed. For separation of 199 Tl)I), about 5 mL of raw material solution obtained was transferred to 201 x 8 type anion exchange resin column which had been equilibrated with 4 mol/L HCl. The 199 Tl(I) and Au(III) were desorbed separately with the eluants (90% of aqueous diamide solution,, and 2 mol/L HCL∼5% thiourea) at the flow rate of 0.25 mL/min. After separation, the 10 mL concentrated nitric acid was added to the 199 Tl collected solution to destroy and remove the aqueous diamide solution, then 4 mol/L HCl was added and heated up to remove NO 3 - . The TlCl injection with pH = 5 was made up by using physiological saline. After filtering the 199 TlCl injection was sterilized at 137.3 kPa, 120 deg C about 30 min in an autoclave. The 199 TlCl injection was used in the animal pyrogen, a bacterial, safety, dispensation and myocardial imaging experiments. The good results have been obtained. Now it has undergone clinical experiments

Two crystal structures of Ag sup + -and Tl sup + -exchanged zeolite X, Ag sub 2 sub 7 Tl sub 6 sub 5 -X and Ag sub 2 sub 3 Tl sub 6 sub 9 -X

CERN Document Server

Kim, S Y; Kim, Y

2002-01-01

Two crystal structures of dehydrated Ag sup + -and Tl sup + -exchanged zeolite X (Ag sub 2 sub 7 Tl sub 6 sub 5 -X and Ag sub 2 sub 3 Tl sub 6 sub 9 -X) have been determined by single-crystal X-ray diffraction techniques in the cubic space group Fd3 at 21(1) .deg. C (a = 24.758(4) A, a = 24.947(4) A, respectively). Their structures were refined to the final error indices R sub 1 = 0.055 and wR sub 2 = 0.057 with 375 reflections, and R sub 1 = 0.058 and wR sub 2 = 0.057 with 235 reflections, respectively, for which I> 3 sigma(I). In the structure of Ag sub 2 sub 7 Tl sub 6 sub 5 -X, 27 Ag sup + ions were found at two crystallographic sites: 15 Ag sup + ions at site I at the center of the hexagonal prism and the remaining 12 Ag sup + ions at site II' in the sodalite cavity. Sixty-five Tl sup + ions were located at three crystallographic sites: 20 Tl sup + ions at site II opposite single six-rings in the supercage, 18 Tl sup + ions at site I' in the sodalite cavity opposite the D6Rs, and the remaining 27 Tl sup ...

DWPF simulant CPC studies for SB8

Energy Technology Data Exchange (ETDEWEB)

Koopman, D. C.; Zamecnik, J. R.

2013-06-25

The Savannah River National Laboratory (SRNL) accepted a technical task request (TTR) from Waste Solidification Engineering to perform simulant tests to support the qualification of Sludge Batch 8 (SB8) and to develop the flowsheet for SB8 in the Defense Waste Processing Facility (DWPF). These efforts pertained to the DWPF Chemical Process Cell (CPC). Separate studies were conducted for frit development and glass properties (including REDOX). The SRNL CPC effort had two primary phases divided by the decision to drop Tank 12 from the SB8 constituents. This report focuses on the second phase with SB8 compositions that do not contain the Tank 12 piece. A separate report will document the initial phase of SB8 testing that included Tank 12. The second phase of SB8 studies consisted of two sets of CPC studies. The first study involved CPC testing of an SB8 simulant for Tank 51 to support the CPC demonstration of the washed Tank 51 qualification sample in the SRNL Shielded Cells facility. SB8-Tank 51 was a high iron-low aluminum waste with fairly high mercury and moderate noble metal concentrations. Tank 51 was ultimately washed to about 1.5 M sodium which is the highest wash endpoint since SB3-Tank 51. This study included three simulations of the DWPF Sludge Receipt and Adjustment Tank (SRAT) cycle and Slurry Mix Evaporator (SME) cycle with the sludge-only flowsheet at nominal DWPF processing conditions and three different acid stoichiometries. These runs produced a set of recommendations that were used to guide the successful SRNL qualification SRAT/SME demonstration with actual Tank 51 washed waste. The second study involved five SRAT/SME runs with SB8-Tank 40 simulant. Four of the runs were designed to define the acid requirements for sludge-only processing in DWPF with respect to nitrite destruction and hydrogen generation. The fifth run was an intermediate acid stoichiometry demonstration of the coupled flowsheet for SB8. These runs produced a set of processing

DWPF simulant CPC studies for SB8

International Nuclear Information System (INIS)

Koopman, D. C.; Zamecnik, J. R.

2013-01-01

The Savannah River National Laboratory (SRNL) accepted a technical task request (TTR) from Waste Solidification Engineering to perform simulant tests to support the qualification of Sludge Batch 8 (SB8) and to develop the flowsheet for SB8 in the Defense Waste Processing Facility (DWPF). These efforts pertained to the DWPF Chemical Process Cell (CPC). Separate studies were conducted for frit development and glass properties (including REDOX). The SRNL CPC effort had two primary phases divided by the decision to drop Tank 12 from the SB8 constituents. This report focuses on the second phase with SB8 compositions that do not contain the Tank 12 piece. A separate report will document the initial phase of SB8 testing that included Tank 12. The second phase of SB8 studies consisted of two sets of CPC studies. The first study involved CPC testing of an SB8 simulant for Tank 51 to support the CPC demonstration of the washed Tank 51 qualification sample in the SRNL Shielded Cells facility. SB8-Tank 51 was a high iron-low aluminum waste with fairly high mercury and moderate noble metal concentrations. Tank 51 was ultimately washed to about 1.5 M sodium which is the highest wash endpoint since SB3-Tank 51. This study included three simulations of the DWPF Sludge Receipt and Adjustment Tank (SRAT) cycle and Slurry Mix Evaporator (SME) cycle with the sludge-only flowsheet at nominal DWPF processing conditions and three different acid stoichiometries. These runs produced a set of recommendations that were used to guide the successful SRNL qualification SRAT/SME demonstration with actual Tank 51 washed waste. The second study involved five SRAT/SME runs with SB8-Tank 40 simulant. Four of the runs were designed to define the acid requirements for sludge-only processing in DWPF with respect to nitrite destruction and hydrogen generation. The fifth run was an intermediate acid stoichiometry demonstration of the coupled flowsheet for SB8. These runs produced a set of processing

Crystallographic study of the intermediate compounds SbZn, Sb3Zn4 and Sb2Zn3

International Nuclear Information System (INIS)

Adjadj, Fouzia; Belbacha, El-djemai; Bouharkat, Malek; Kerboub, Abdellah

2006-01-01

The processes of development of semiconductor ceramics made up of bismuth, antimony and zinc often require during their preparation to know the nature of the involved phases. For that, it is always essential to refer to the diagrams of balance between phases of the binary systems or ternary. We presented in this work the study by X-rays diffraction relating to the intermediate compounds SbZn, Sb 3 Zn 4 and Sb 2 Zn 3 . The analysis by X-rays is often useful to give supplement the results of the other experimental methods

Firing temperature of pottery using TL and OSL techniques

International Nuclear Information System (INIS)

Polymeris, G.S.; Sakalis, A.; Papadopoulou, D.; Dallas, G.; Kitis, G.; Tsirliganis, N.C.

2007-01-01

Several methods of thermal analysis are used to determine in the laboratory the firing temperature of ancient ceramic sherds. These methods are based primarily on changes of physical characteristics occurring when clay minerals are heated. The luminescence properties of quartz grains in a ceramic matrix also undergo certain changes during firing. The possibility of measuring the sensitivity change (sensitization) of quartz in order to determine the firing temperature of archeological ceramic artifacts was investigated. The sensitivity change was studied for both the thermoluminescence (TL) and the optically stimulated luminescence (OSL) signal for a ceramic sample of known firing temperature. Various segments of the sample were annealed to a different temperature. Subsequently, the initial sensitivity, as well as the thermal and the pre-dose sensitization were measured for both TL and OSL at room temperature as a function of the annealing temperature. The obtained TL glow curves showed different shapes for annealing temperatures above the firing temperature. Thermal and pre-dose sensitizations also exhibited a similar, although less prominent, rise. The OSL signal was analyzed by integrating the raw signal over the initial second of stimulation. The initial sensitivity showed an abrupt change for annealing temperatures around the firing temperature. An alternative approach used for the analysis of the OSL signal involved a full-component resolved sensitization study. The same abrupt change for the initial sensitivity of both the first and second components was observed, as well as, a clear but not very prominent thermal sensitization trend for annealing temperatures above the firing temperature

Trithallium tetraselenophosphate Tl3PSe4, and trithallium tetrathioarsenate, Tl3AsS4, by neutron time-of-flight diffraction

International Nuclear Information System (INIS)

Alkire, R.W.; Vergamini, P.J.; Larson, A.C.; Morosin, B.

1984-01-01

Room-temperature (293 K) single-crystal structure determinations of the isostructural materials Tl 3 PSe 4 and Tl 3 AsS 4 were performed at the Los Alamos National Laboratory Pulsed Neutron Facility. For Tl 3 PSe 4 : Msub(r) = 959.92, Pcmn, a = 9.276 (1), b = 11.036 (2), c = 9.058 (1) A, V = 927.27 A 3 , Z = 4, Dsub(m) = 6.87 (2), Dsub(x) = 6.876 Mg m -3 , lambdasub(neutron) = 0.5 → 5.2 A, F(000) = 252.5 fm. For Tl 3 AsS 4 : Msub(r) = 816.29, Pcmn, a = 9.084 (3), b = 10.877 (3), c = 8.877 (3) A, V = 877.11 A 3 , Z = 4, Dsub(m) = 6.18 (2), Dsub(x) = 6.181 Mg m -3 , lambdasub(neutron) = 0.5 → 5.2 A, F(000) = 177.2 fm. For Tl 3 PSe 4 (Tl 3 AsS 4 ), 1929 (1013) reflections were measured with I > 3sigma(I) and refined by full-matrix least squares to R(F) = 0.061 (0.063). Results on atomic refinement from this study represent an order of magnitude increase in precision over previous single-crystal X-ray structural work using Mo Kα radiation. The PSe 4 3- (AsS 4 3- ) groups have essentially tetrahedral configurations and one Tl + ion shows large anisotropic thermal motion which is structure related. (Auth.)

Syntheses, crystal structures, and characterization of two new Tl{sup +}-Cu{sup 2+}-Te{sup 6+} oxides: Tl{sub 4}CuTeO{sub 6} and Tl{sub 6}CuTe{sub 2}O{sub 10}

Energy Technology Data Exchange (ETDEWEB)

Yeon, Jeongho; Kim, Sang-Hwan [Department of Chemistry, University of Houston, 136 Fleming Building, Houston, TX 77204-5003 (United States); Green, Mark A. [Department of Materials Science and Engineering, University of Maryland, College Park, MD, 20742-2115 and NIST Center for Neutron Research, National Institute of Standard and Technology, 100 Bureau Drive, Gaithersburg, MD 20899-6103 (United States); Bhatti, Kanwal Preet; Leighton, C. [Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN 55455-0132 (United States); Shiv Halasyamani, P., E-mail: psh@uh.edu [Department of Chemistry, University of Houston, 136 Fleming Building, Houston, TX 77204-5003 (United States)

2012-12-15

Crystals and polycrystalline powders of two new oxide materials, Tl{sub 4}CuTeO{sub 6} and Tl{sub 6}CuTe{sub 2}O{sub 10}, have been synthesized by hydrothermal and solid-state methods. The materials were structurally characterized by single-crystal X-ray diffraction. Tl{sub 4}CuTeO{sub 6} and Tl{sub 6}CuTe{sub 2}O{sub 10} exhibit one dimensional anionic slabs of [CuTeO{sub 6}]{sup 4-} and [CuTe{sub 2}O{sub 10}]{sup 6-}, respectively. Common to both slabs is the occurrence of Cu{sup 2+}O{sub 4} distorted squares and Te{sup 6+}O{sub 6} octahedra. The slabs are separated by Tl{sup +} cations. For Tl{sub 4}CuTeO{sub 6}, magnetic measurements indicate a maximum at {approx}8 K in the temperature dependence of the susceptibility. Low temperature neutron diffraction data confirm no long-range magnetic ordering occurs and the susceptibility was adequately accounted for by fits to a Heisenberg alternating chain model. For Tl{sub 6}CuTe{sub 2}O{sub 10} on the other hand, magnetic measurements revealed paramagnetism with no evidence of long-range magnetic ordering. Infrared, UV-vis spectra, thermogravimetric, and differential thermal analyses are also reported. Crystal data: Tl{sub 4}CuTeO{sub 6}, Triclinic, space group P-1 (No. 2), a=5.8629(8) A, b=8.7848(11) A, c=9.2572(12) A, {alpha}=66.0460(10), {beta}=74.2010(10), {gamma}=79.254(2), V=417.70(9) A{sup 3}, and Z=2; Tl{sub 6}CuTe{sub 2}O{sub 10}, orthorhombic, space group Pnma (No. 62), a=10.8628(6) A, b=11.4962(7) A, c=10.7238(6) A, V=1339.20(13) A{sup 3}, and Z=4. - Graphical Abstract: Two new oxide materials, Tl{sub 4}CuTeO{sub 6} and Tl{sub 6}CuTe{sub 2}O{sub 10}, have been synthesized and characterized. The materials exhibit one dimensional crystal structures consisting of CuO{sub 4} and TeO{sub 6} polyhedra. Highlights: Black-Right-Pointing-Pointer Two New Tl-Te-Cu-oxides have been synthesized and structurally characterized. Black-Right-Pointing-Pointer For Tl{sub 4}CuTeO{sub 6}, magnetic measurements indicate a

Phase diagram of the Sb-Se-I system and thermodynamic properties of SbSeI

International Nuclear Information System (INIS)

Aliev, Z.S.; Musaeva, S.S.; Babanly, D.M.; Shevelkov, A.V.; Babanly, M.B.

2010-01-01

The Sb-Se-I system was investigated by using the DTA and XRD analyses and EMF measurements with an antimony electrode. The T-x diagram of the binary Sb-I system was accurately redefined. A number of polythermal sections and the projection of the liquidus surface were constructed. The fields of the primary crystallization, as well as the types and coordinates of non- and monovariant equilibria were determined. It is shown that the quasi-binary sections Sb 2 Se 3 -SbI 3 , Sb-SbSeI, SbI 3 -Se, and SbSeI-Se triangulate the Sb-Se-I system, leading to five independent subsystems. A broad area of immiscibility, that overlaps a certain part of the antimony primary crystallization field, was found. From the EMF measurements, the partial molar functions of antimony (ΔG-bar, ΔH-bar, ΔS-bar) as well as standard integral thermodynamic functions of SbSeI were calculated. The latter were found to have the following values: ΔG f,298 0 =-80.12±1.81kJ/mol; ΔH f,298 0 =-77.3±1.8kJ/mol; S 298 0 =155.2±9.5J/(molK).

Phase diagram of the Sb-Se-I system and thermodynamic properties of SbSeI

Energy Technology Data Exchange (ETDEWEB)

Aliev, Z S; Musaeva, S S; Babanly, D M [Baku State University, General and Inorganic Chemistry Department (Azerbaijan); Shevelkov, A.V., E-mail: shev@inorg.chem.msu.r [Moscow Lomonosov State University, Chemistry Department (Russian Federation); Babanly, M.B., E-mail: Babanly_mb@rambler.r [Baku State University, General and Inorganic Chemistry Department (Azerbaijan)

2010-09-03

The Sb-Se-I system was investigated by using the DTA and XRD analyses and EMF measurements with an antimony electrode. The T-x diagram of the binary Sb-I system was accurately redefined. A number of polythermal sections and the projection of the liquidus surface were constructed. The fields of the primary crystallization, as well as the types and coordinates of non- and monovariant equilibria were determined. It is shown that the quasi-binary sections Sb{sub 2}Se{sub 3}-SbI{sub 3}, Sb-SbSeI, SbI{sub 3}-Se, and SbSeI-Se triangulate the Sb-Se-I system, leading to five independent subsystems. A broad area of immiscibility, that overlaps a certain part of the antimony primary crystallization field, was found. From the EMF measurements, the partial molar functions of antimony ({Delta}G-bar, {Delta}H-bar, {Delta}S-bar) as well as standard integral thermodynamic functions of SbSeI were calculated. The latter were found to have the following values: {Delta}G{sub f,298}{sup 0}=-80.12{+-}1.81kJ/mol; {Delta}H{sub f,298}{sup 0}=-77.3{+-}1.8kJ/mol; S{sub 298}{sup 0}=155.2{+-}9.5J/(molK).

Removal of Sb(III and Sb(V by Ferric Chloride Coagulation: Implications of Fe Solubility

Directory of Open Access Journals (Sweden)

Muhammad Ali Inam

2018-04-01

Full Text Available Coagulation and precipitation appear to be the most efficient and economical methods for the removal of antimony from aqueous solution. In this study, antimony removal from synthetic water and Fe solubility with ferric chloride (FC coagulation has been investigated. The effects of pH, FC dosage, initial antimony loading and mixed Sb(III, Sb(V proportions on Fe solubility and antimony removal were studied. The results showed that the Sb(III removal efficiency increased with the increase of solution pH particularly due to an increase in Fe precipitation. The Sb(V removal was influenced by the solution pH due to a change in Fe solubility. However, the Fe solubility was only impaired by the Sb(III species at optimum pH 7. The removal efficiencies of both Sb species were enhanced with an increase in FC dose. The quantitative analysis of the isotherm study revealed the strong adsorption potential of Sb(III on Fe precipitates as compared to Sb(V. Furthermore, the removal behavior of antimony was inhibited in mixed proportion with high Sb(V fraction. In conclusion, this study contributes to better understanding the fate of Sb species, their mobilities, and comparative removal behavior, with implications for Fe solubility using ferric chloride in different aqueous environments.

Intrinsic thermoluminescence of NaCl:Tl in UV dosimetry

International Nuclear Information System (INIS)

Barghare, S.P.; Joshi, R.V.; Joshi, T.R.; Kathuria, S.P.

1982-01-01

NaCl:Tl(T) phosphor is found to have high intrinsic thermoluminescence (TL) sensitivity to 253.7 nm UV-radiation. The dosimetric glow peak II grows sublinearly with increase in UV dose in the range 10 3 to 10 6 JM -2 . The other requirements of an efficient dosimeter material such as high storage stability, matching of the spectral response of detector tube and TL-emission from phosphor, reproducibility, desirable size and shape, easy availability in powder, pellet and crystal forms at cheaper rates, and repeated re-usability of the same phosphor without much difficulty, etc., are additional factors which strengthen the claim of NaCl:Tl(T) phosphor as UV dosimetric material. It is proposed that present NaCl:Tl(T) material is suitable TL-phosphor for UV dosimetry in the range 10 3 to 10 6 JM -2 . (author)

Bioaccessibility of selected trace metals in urban PM{sub 2.5} and PM{sub 10} samples: a model study

Energy Technology Data Exchange (ETDEWEB)

Falta, Thomas; Koellensperger, Gunda; Hann, Stephan [University of Natural Resources and Applied Life Sciences, Division of Analytical Chemistry, Vienna (Austria); Limbeck, Andreas [Vienna University of Technology, Institute of Chemical Technologies and Analytics, Vienna (Austria)

2008-02-15

Bioaccessibility of trace metals originating from urban particulate matter was assessed in a worst case scenario to evaluate the uptake and thus the hazardous potential of these metals via gastric juice. Sampling was performed over a period of about two months at the Getreidemarkt in downtown Vienna. Concentrations of the assayed trace metals (Ti, Cr, Mn, Co, Ni, Cu, Zn, Mo, Ag, Cd, Sn, Sb, Tl and Pb) were determined in PM{sub 2.5} and PM{sub 10} samples by ICP-MS. The metal concentrations in sampled air were in the low picogram to high nanogram per cubic metre range. The concentrations in PM{sub 2.5} samples were generally lower than those in PM{sub 10} samples. The average daily intake of these metals by inhalation for a healthy adult was estimated to be in the range of <1 ng (Tl) to >1,000 ng (Zn). To estimate the accessibility of the inhaled and subsequently ingested metals (i.e. after lung clearance had taken place) in the size range from 2.5- to 10-{mu}m aerodynamic equivalent diameter, a batch-extraction with synthetic gastric juice was performed. The data were used to calculate the bioaccessibility of the investigated trace metals. Extractable fractions ranged from 2.10% (Ti in PM{sub 2.5}) to 91.0% (Cd in PM{sub 2.5}), thus yielding bioaccessible fractions (PM{sub 2.5-10}) from 0.16 ng (Ag) to 178 ng (Cu). (orig.)

Low-temperature synthesis of single-phase Co7Sb2O12

International Nuclear Information System (INIS)

Brito, M.S.L.; Escote, M.T.; Santos, C.O.P.; Lisboa-Filho, P.N.; Leite, E.R.; Oliveira, J.B.L.; Gama, L.; Longo, E.

2004-01-01

Polycrystalline Co 7 Sb 2 O 12 compounds have been synthesized by a chemical route, which is based on a modified polymeric precursor method. In order to study the physical properties of the samples, X-ray diffraction (XRD), thermal analyses (TG and DSC), infrared spectroscopy (IR), specific surface area (BET), and magnetization measurements were performed on these materials. Characterization through XRD revealed that the samples are single-phase after a heat-treatment at 1100 deg. C for 2 h, while the X-ray patterns of the samples heat-treated at lower temperatures revealed the presence of additional Bragg reflections belonging to the Co 6 Sb 2 O 6 phase. These data were analyzed by means of Rietveld refinement and further analyze showed that Co 7 Sb 2 O 12 displays an inverse spinel crystalline structure. In this structure, the Co 2+ ions occupy the eight tetrahedral positions, and the sixteen octahedral positions are randomly occupied by the Sb 5+ and Co 2+ ions. IR studies disclosed two strong absorption bands, ν 1 and ν 2 , in the expected spectral range for a spinel-type binary oxide with space group Fd3m. Exploratory studies concerning the magnetic properties indicated that this sample presents a spin-glass transition at T f ∼ 64 K

Effect of InSb/In0.9Al0.1Sb superlattice buffer layer on the structural and electronic properties of InSb films

Science.gov (United States)

Zhao, Xiaomeng; Zhang, Yang; Guan, Min; Cui, Lijie; Wang, Baoqiang; Zhu, Zhanping; Zeng, Yiping

2017-07-01

The effect of InSb/In0.9Al0.1Sb buffer layers on InSb thin films grown on GaAs (0 0 1) substrate by molecular beam epitaxy (MBE) is investigated. The crystal quality and the surface morphology of InSb are characterized by XRD and AFM. The carrier transport property is researched through variable temperature hall test. The sharp interface between InSb/In0.9Al0.1Sb is demonstrated important for the high quality InSb thin film. We try different superlattice buffer layers by changing ratios, 2-0.5, thickness, 300-450 nm, and periods, 20-50. According to the function of the dislocation density to the absolute temperature below 150 K with different periods of SL buffers, we can find that the number of periods of superlattice is a major factor to decrease the density of threading dislocations. With the 50 periods SL buffer layer, the electron mobility of InSb at the room temperature and liquid nitrogen cooling temperature is ∼63,000 and ∼4600 cm2/V s, respectively. We deduce that the interface in the SL structure works as a filter layer to prevent the dislocation propagating to the upper InSb thin films.

Low-level simultaneous determination of As and Sb in standard reference materials using radiochemical neutron activation analysis with isotopic 77As and 125Sb tracers

International Nuclear Information System (INIS)

Byrne, A.R.

1987-01-01

The aim of the present work was to develop an older method used in our laboratory based on selective solvent extraction of As and Sb as their iodides with toluene, and by the use of the radioisotopic tracers 77 As and 125 Sb, to improve the accuracy by better control of the radiochemical yields. 77 As was produced for each sample run by concurrent irradiation of a few mg of GeO 2 followed by a rapid separation of 77 As from 77 Ge. The radiochemically purified sample fraction containing 76+77 As and 122+125 Sb was counted on a Ge detector in good geometry. The γ-lines of the four nuclides do not mutually interfere so that a combined measurement of As and Sb may be made. The method was applied to IAEA Milk Powder A-11, Animal Muscle H-4, Bowen's Kale and some other SRMs. The results obtained are discussed in the light of literature measurements. From present and previous results, together with data by Heydorn, the presently accepted value for As in Bowen's Kale of 140 ngxg -1 may be 20% too high. (orig.)

The automated Risoe TL dating reader system

International Nuclear Information System (INIS)

Boetter-Jensen, L.

1988-01-01

The features of the new modified Riso TL dating reader system are described. A vacuum chamber that accommodates the entire 24-position sample changer unit has been designed. The vacuum and N 2 -gas functions are software-controlled. A newly designed heater system is capable of repeated heating cycles to 700 0 C. The sample changer system accommodates fine-grain discs as well as planchettes for coarse grains. Two software-controlled beta irradiators can be attached to the reader, e.g. for predose measurement. The software allows a user without programming expertise to create any desired measuring sequence, and to store and recall data and glow curves for making analyses. (author)

Exploring the thermoelectric and magnetic properties of uranium selenides: Tl2Ag2USe4 and Tl3Cu4USe6

International Nuclear Information System (INIS)

Azam, Sikander; Khan, Saleem Ayaz; Din, Haleem Ud; Khenata, Rabah; Goumri-Said, Souraya

2016-01-01

The electronic, magnetic and thermoelectric properties of Tl 2 Ag 2 USe 4 and Tl 3 Cu 4 USe 6 compounds were investigated using the full potential linear augmented plane wave (FP-LAPW) method based on the density functional theory (DFT). The exchange correlation was treated with the generalized gradient approximation plus optimized effective Hubbard parameter and spin–orbit coupling (GGA+U+SOC). The present uranium selenides show narrow direct energy band gap values of 0.7 and 0.875 eV for Tl 2 Ag 2 USe 4 and Tl 3 Cu 4 USe 6 respectively. For both selenides U-d/f states are responsible for electrical transport properties. Uranium atoms were the most contributors in the magnetic moment compared to other atoms and show ferromagnetic nature. The spin density isosurfaces show the polarization of neighboring atoms of Uranium, such as silver/copper and selenium. Thermoelectric calculations reveal that Tl 3 Cu 4 USe 6 is more suitable for thermoelectric device applications than Tl 2 Ag 2 USe 4 . - Highlights: • Electronic, magnetic and thermoelectric properties of uranium selenides are investigated with DFT. • They show a narrow direct energy band gap of 0.7 and 0.875 eV. • U-d/f states are responsible for electrical transport properties. • Tl 3 Cu 4 USe 6 is more suitable for thermoelectric device applications than Tl 2 Ag 2 USe 4 .

Activation energies from blue- and red-thermoluminescence (TL) of quartz grains and mean lives of trapped electrons related to natural red-TL

International Nuclear Information System (INIS)

Hashimoto, T.; Kojima, M.; Shirai, N.; Ichino, M.

1993-01-01

A three-dimensional representation of thermoluminescence (TL) spectra has been established by employing an image intensifier unit combined with a simple spectrophotometer and a microcomputer. By means of this TL spectrometric system, natural quartz grains could be distinguished as either blue-and/or red-TL ones. In these blue- and red-TL wavelength regions, activation energies from artificially irradiated quartz grains are evaluated using a repeated initial rise method. An apparent difference of activation energies in the two colorations was observed for dune sands presumably originating from different quartz sources. On the other hand, quartz grains extracted from a volcanic ash sediment showed completely similar activation energies in both TL color regions over all temperatures. Subsequently, the kinetic parameters were derived for the naturally occurring red-TL, possessing an apparent single peak around 340 o C, from volcanically originating quartz grains by fitting a theoretical equation to the glow curves, after evaluating activation energies. On the basis of the empirical kinetic parameters, the mean life of trapped electrons relating to a main 340 o C peak has been proved to be 1 million years, and a secondary weak peak around 280 o C in the natural red-TL glow curve has been confirmed. (author)

Color centers in heavily irradiated CsI(Tl) crystals

International Nuclear Information System (INIS)

Yakovlev, V.; Meleshko, A.; Trefilova, L.

2008-01-01

The absorption and luminescence properties of CsI(Tl) crystals colored by irradiation are studied by the method of the time-resolved spectroscopy. The scheme of the electron transitions in CsI(Tl) crystal is suggested to explain the appearance of the color centers under exposure to the near-UV light. It is established that either of the two types activator color centers holds the charge carrier with opposite sign. The model of the hole Tl 2+ v c - activator color center is suggested. According to the model the positive charge of Tl 2+ ion is compensated by the negative charge of a close cation vacancy v c - . The color center emission reveals in the cathode-luminescence spectrum of the colored CsI(Tl) crystal. The high-dose irradiation of CsI(Tl) crystal results in the reduction of the decay time of the near-thallium self-trapped excitons (STE) emission. The decay kinetics of Tl 2+ v c - emission contains the time components typical for the decay kinetics of near-thallium STE emission. The reason of the observed effects is the energy transfer from the near-thallium STE excitons to the color centers via the inductive-resonant mechanism

Ab initio calculations of the electron spectrum and density of states of TlFeS{sub 2} and TlFeSe{sub 2} crystals

Energy Technology Data Exchange (ETDEWEB)

Ismayilova, N. A., E-mail: ismayilova-narmin-84@mail.ru; Orudjev, H. S.; Jabarov, S. H. [Azerbaijan National Academy of Sciences, Institute of Physics (Azerbaijan)

2017-04-15

The results of ab initio calculations of the electron spectrum of TlFeS{sub 2} and TlFeSe{sub 2} crystals in the antiferromagnetic phase are reported. Calculations are carried out in the context of the density functional theory. The origin of the bands of s, p, and d electron states of Tl, Fe, S, and Se atoms is studied. It is established that, in the antiferromagnetic phase, the crystals possess semiconductor properties. The band gaps are found to be 0.05 and 0.34 eV for TlFeS{sub 2} and TlFeSe{sub 2} crystals, respectively.

Effects of antimony (Sb) on electron trapping near SiO{sub 2}/4H-SiC interfaces

Energy Technology Data Exchange (ETDEWEB)

Mooney, P. M.; Jiang, Zenan; Basile, A. F. [Physics Department, Simon Fraser University, Burnaby, British Columbia V5A 1S6 (Canada); Zheng, Yongju; Dhar, Sarit [Physics Department, Auburn University, Auburn, Alabama 36849 (United States)

2016-07-21

To investigate the mechanism by which Sb at the SiO{sub 2}/SiC interface improves the channel mobility of 4H-SiC MOSFETs, 1 MHz capacitance measurements and constant capacitance deep level transient spectroscopy (CCDLTS) measurements were performed on Sb-implanted 4H-SiC MOS capacitors. The measurements reveal a significant concentration of Sb donors near the SiO{sub 2}/SiC interface. Two Sb donor related CCDLTS peaks corresponding to shallow energy levels in SiC were observed close to the SiO{sub 2}/SiC interface. Furthermore, CCDLTS measurements show that the same type of near-interface traps found in conventional dry oxide or NO-annealed capacitors are present in the Sb implanted samples. These are O1 traps, suggested to be carbon dimers substituted for O dimers in SiO{sub 2}, and O2 traps, suggested to be interstitial Si in SiO{sub 2}. However, electron trapping is reduced by a factor of ∼2 in Sb-implanted samples compared with samples with no Sb, primarily at energy levels within 0.2 eV of the SiC conduction band edge. This trap passivation effect is relatively small compared with the Sb-induced counter-doping effect on the MOSFET channel surface, which results in improved channel transport.

Investigation of TL, OSL and PTTL properties of Mg2SiO4:Tb dosimeters

International Nuclear Information System (INIS)

Oguz, K. F.; Goekce, M.; Karali, T.; Harmansah, C.

2010-01-01

In this study thermoluminescence (TL) and optically stimulated luminescence (OSL) properties of Mg 2 SiO 4 :Tb in the form of sintered pellets were investigated. Mg 2 SiO 4 :Tb is a recently developed dosimetric material which offers high sensitivity for TL and OSL in dosimetric applications. Thermoluminescence glow curve of Tb doped Mg 2 SiO 4 samples show a glow peak at about 200 degree Celsius with two small peaks at about 275 and 330 degree Celsius, respectively. OSL experiments showed that blue light (470 nm) is six times more efficient than green light (532 nm) to stimulate the OSL emission. The aim of this study was to determine the TL and OSL fading properties of Mg 2 SiO 4 : Tb using OSL and TL methods. In addition, PTTL properties of the Mg 2 SiO 4 : Tb was investigated by using blue LEDs, UV lamp and blue laser. Investigations on the fading properties also showed that the TL signal fades % 10 in a period of 1 month and OSL signal fades % 10 in a period of 3 month, which then the signal remains relatively stable for longer periods.

Recovering Parameters of Johnson's SB Distribution

Science.gov (United States)

Bernard R. Parresol

2003-01-01

A new parameter recovery model for Johnson's SB distribution is developed. This latest alternative approach permits recovery of the range and both shape parameters. Previous models recovered only the two shape parameters. Also, a simple procedure for estimating the distribution minimum from sample values is presented. The new methodology...

Comparison of 201Tl solution sources in UK hospitals, 2001

International Nuclear Information System (INIS)

Baker, M.; Woods, M.

2001-01-01

During recent years, concerns have been raised within the nuclear medicine field about the accuracy of activity measurements for 201 Tl. And indeed, NPL calibrations repeatedly indicated that the level of impurities present in such samples and the significant amount of activity adsorbed onto the glass wall of the container could produce erroneous results. In addition, the standard P6 vials, in which 201 Tl solution had been previously supplied, were recently replaced with the new ''10R Type 1 plus'' Schott vials. To assess the magnitude of these effects on the accuracy of clinical measurements of the activity of 201 Tl, an intercomparison exercise was conducted between the National Physical Laboratory (NPL), Nycomed-Amersham (NA) and the UK hospital physics community. The majority of the 273 reported results were within the ± 10 % limit of accuracy that hospitals aim to achieve for diagnosis, biased high. The tendency to overestimate the activity was more evident for syringe measurements. The exercise also revealed that the adsorption losses experienced with P6 vials had been solved by the introduction of the 10R vials, but individual calibrators need to be recalibrated for this new container. (author)

Crystallization behavior of Ge-doped eutectic Sb70Te30 films in optical disks

International Nuclear Information System (INIS)

Khulbe, Pramod K.; Hurst, Terril; Mansuripur, Masud; Horie, Michikazu

2002-01-01

We report laser-induced crystallization behavior of binary Sb-Te and ternary Ge-doped eutectic Sb70Te30 thin film samples in a typical quadrilayer stack as used in phase-change optical disk data storage. Several experiments have been conducted on a two-laser static tester in which one laser operating in pulse mode writes crystalline marks on amorphous film or amorphous marks on crystalline film, while the second laser operating at low-power cw mode simultaneously monitors the progress of the crystalline or amorphous mark formation in real time in terms of the reflectivity variation. The results of this study show that the crystallization kinetics of this class of film is strongly growth dominant, which is significantly different from the crystallization kinetics of stochiometric Ge-Sb-Te compositions. In Sb-Te and Ge-doped eutectic Sb70Te30 thin-film samples, the crystallization behavior of the two forms of amorphous states, namely, as-deposited amorphous state and melt-quenched amorphous state, remains approximately same. We have also presented experiments showing the effect of the variation of the Sb/Te ratio and Ge doping on the crystallization behavior of these films

Near-surface depletion of antimony during the growth of GaAsSb and GaAs/GaAsSb nanowires

Energy Technology Data Exchange (ETDEWEB)

Kauko, H.; Helvoort, A. T. J. van, E-mail: a.helvoort@ntnu.no [Department of Physics, Norwegian University of Science and Technology (NTNU), Trondheim (Norway); Fimland, B. O.; Munshi, A. M. [Department of Electronics and Telecommunications, NTNU, Trondheim (Norway); Grieb, T.; Müller, K.; Rosenauer, A. [Institut für Festkörperphysik, Universität Bremen, Bremen (Germany)

2014-10-14

The near-surface reduction of the Sb mole fraction during the growth of GaAsSb nanowires (NWs) and GaAs NWs with GaAsSb inserts has been studied using quantitative high-angle annular dark field scanning transmission electron microscopy (STEM). A model for diffusion of Sb in the hexagonal NWs was developed and employed in combination with the quantitative STEM analysis. GaAsSb NWs grown by Ga-assisted molecular beam epitaxy (MBE) and GaAs/GaAsSb NWs grown by Ga- and Au-assisted MBE were investigated. At the high temperatures employed in the NW growth, As-Sb exchange at and outward diffusion of Sb towards the surface take place, resulting in reduction of the Sb concentration at and near the surface in the GaAsSb NWs and the GaAsSb inserts. In GaAsSb NWs, an increasing near-surface depletion of Sb was observed towards the bottom of the NW due to longer exposure to the As beam flux. In GaAsSb inserts, an increasing change in the Sb concentration profile was observed with increasing post-insert axial GaAs growth time, resulting from a combined effect of radial GaAs overgrowth and diffusion of Sb. The effect of growth temperature on the diffusion of Sb in the GaAsSb inserts was identified. The consequences of these findings for growth optimization and the optoelectronic properties of GaAsSb are discussed.

Preparation, characterization of Sb-doped ZnO nanocrystals and their excellent solar light driven photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Nasser, Ramzi; Othmen, Walid Ben Haj [Laboratoire de Physico-Chimie des Matériaux Minéraux et leurs Applications, Centre National de Recherches en Sciences des Matériaux, B.P. 95 Hammam-Lif, 2050 (Tunisia); Département de Physique, Faculté des Sciences de Tunis, University of Tunis El Manar 2092 (Tunisia); Elhouichet, Habib, E-mail: habib.elhouichet@fst.rnu.tn [Laboratoire de Physico-Chimie des Matériaux Minéraux et leurs Applications, Centre National de Recherches en Sciences des Matériaux, B.P. 95 Hammam-Lif, 2050 (Tunisia); Département de Physique, Faculté des Sciences de Tunis, University of Tunis El Manar 2092 (Tunisia); Férid, Mokhtar [Laboratoire de Physico-Chimie des Matériaux Minéraux et leurs Applications, Centre National de Recherches en Sciences des Matériaux, B.P. 95 Hammam-Lif, 2050 (Tunisia)

2017-01-30

Highlights: • Sb-ZnO was obtained by modified sol-gel method using citric acid as stabilizing agent. • Sb incorporated both in lattice and interstitial sites. • The formation of (Sb{sub Zn}–2 V{sub Zn}) acceptor level was revealed by photoluminescence studies. • Optimum Sb content to show higher photocatalytic activity was found to be 3%. - Abstract: In the present study, undoped and antimony (Sb) doped ZnO nanocrystals (NCs) were prepared by a simple and economical sol-gel method. X-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed the purity of the obtained phase and its high crystallinity. Raman analysis confirms the hexagonal Wurtzite ZnO structure. According to the diffuse reflectance results, the band gap was found to decrease up to 3% of Sb doping (ZSb3 sample). The results of X-ray photoelectron spectroscopy (XPS) measurements reveal that Sb ions occupied both Zn and interstitials sites. The successful substitution of antimony in ZnO lattice suggests the formation of the complex (Sb{sub Zn}–2 V{sub Zn}) acceptor level above the valence band. Particularly for ZSb3 sample, the UV photoluminescence (PL) band presents an obvious red-shift attributed to the formation of this complex. Rhodamine B (RhB) was used to evaluate the photocatalytic activity of Sb-doped ZnO NCs under sunlight irradiation. It was found that oxygen vacancies play a major role in the photocatalytic process by trapping the excited electrons and inhibiting the radiative recombination. During the photocatalytic mechanism, the Sb doping, expressed through the apparition of the (Sb{sub Zn}–2 V{sub Zn}) correspondent acceptor level, enhances the sunlight absorption within the ZnO band gap, which stimulates the generation of hydroxyl radicals and promotes the photocatalytics reaction rates. Such important contribution of the hydroxyl radicals was confirmed experimentally when using ethanol as scavenger in the photocatalytic reaction. The photodegradation

Evaluation of the grass mixture (Faestuca Rubra, Cynodon Dactylon, Lolium Multiflorum and Pennisetum sp.) as Sb phyto-stabilizer in tailings and Sb-rich soils.

Science.gov (United States)

Aurora Armienta, M.; Beltrán-Villavicencio, Margarita; Ruiz-Villalobos, Carlos E.; Labastida, Israel; Ceniceros, Nora; Cruz, Olivia; Aguayo, Alejandra

2017-04-01

Green house experiments were carried out to evaluate the growth and Sb assimilation of a grass assemblage: Faestuca Rubra, Cynodon Dactylon, Lolium Multiflorum and Pennisetum sp, in tailings and Sb-rich soils. Tailings and soil samples were obtained at the Mexican historical mining zone of Zimapán, Central México. More than 6 tailings impoundments are located at the town outskirts and constitute a contamination source from windblown and waterborne deposit on soils, besides acid mine drainage. Four substrates were used in the experiments: 100% tailings, 20% tailings + 80% soil, 50% tailings + 50% soil , and a soil sample far from tailings as a background. Concentrations of Sb ranged from 310 mg/kg to 413 mg/kg in tailings. A pH of 7.43, 1.27% organic matter, and high concentrations of N, K and P indicated adequate conditions for plant growth. The grass assemblage was raised during 21 days as indicated by OECD (Organisation for Economic Co-operation and Development) Guideline 208 Terrestrial Plant Test: Seedling Emergence and Seedling Growth Test. The highest Sb concentrations were measured in plants grown on tailings with 139 mg/kg in the aerial part and 883 mg/kg in roots. Concentrations of Sb decreased as the proportion of tailings diminished with 22.1 mg/kg in the aerial part and 10 mg/kg in roots corresponding to the plants grown in the 20 % tailings + 80% soil . Bioaccumulation (BAC) and bioconcentration factors (BF) of plants grown on tailings (BAC= 0.42, BCF=3.93) indicated their suitability as a phyto-stabilization option. The grass mixture may be thus applied to control windblown particulate tailings taking advantage to their tolerance to high Sb levels.

Statistical Analysis Of Reconnaissance Geochemical Data From ...

African Journals Online (AJOL)

, Co, Mo, Hg, Sb, Tl, Sc, Cr, Ni, La, W, V, U, Th, Bi, Sr and Ga in 56 stream sediment samples collected from Orle drainage system were subjected to univariate and multivariate statistical analyses. The univariate methods used include ...

ESR and TL studies of irradiated Anatolian laurel leaf (Laurus nobilis L.)

Science.gov (United States)

Tepe Çam, Semra; Aydaş, Canan; Engin, Birol; Rabia Yüce, Ülkü; Aydın, Talat; Polat, Mustafa

2012-06-01

Laurel leaf (Laurus nobilis L.) samples that originated from Turkey were analyzed by electron spin resonance (ESR) and thermoluminescence (TL) techniques before and after γ-irradiation. Unirradiated (control) laurel leaf samples exhibit a weak ESR singlet centered at g=2.0020. Besides this central signal were two weak satellite signals situated about 3 mT left and right to it in radiation-induced spectra. The dose-response curve of the radiation-induced ESR signal at g=2.0187 (the left satellite signal) was found to be described well by a power function. Variation of the left satellite ESR signal intensity of irradiated samples at room temperature with time in a long term showed that cellulosic free radicals responsible for the ESR spectrum of laurel leaves were not stable but detectable even after 100 days. Annealing studies at four different temperatures were used to determine the kinetic behavior and activation energy of the radiation-induced cellulosic free radicals responsible from the left satellite signal (g=2.0187) in laurel leaves. TL measurements of the polymineral dust isolated from the laurel leaf samples allowed distinguishing between irradiated and unirradiated samples.

The equilibrium diagram and some properties of alloys Gd5Sb3-Tb5Sb3 system

International Nuclear Information System (INIS)

Azizov, Yu.S.; Abulkhaev, V.D.; Ganiev, I.N.

2001-01-01

The purpose of present work is investigation equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system in total range of concentrations. Equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system investigated by methods of difference-thermal, roentgen-phase and metallographic analyses. For the first time on the base of difference-thermal, roentgen-phase and metallographic analyses was formed the equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system. Was determined the cristal-chemical parameters of solid solutions with general formula Gd x Tb 5 - x Sb 3

Standardization of 201Tl and 55Fe radionuclides in a 4 (PC)-NaI(Tl) coincidence system

International Nuclear Information System (INIS)

Pires, Carlos Augusto

2008-01-01

In the present work the procedure for the standardization of radionuclides using the 4π(PC)-NaI(Tl) coincidence system was developed. The radionuclides selected were 201 Tl, used in nuclear medicine, and 55 Fe primary standard source, used for x-ray spectrometers calibration. The 4π(PC)-NaI(Tl) is composed of a 4 proportional counter operated at 0.1MPa coupled to two NaI(Tl) crystals. The 201 Tl decays by electron capture process followed by a prompt gamma-ray. The disintegration rate was determined by extrapolation technique using two methods: electronic discrimination and external absorbers. The radioactive sources were prepared in a 20 μg cm -2 thick Collodion film. The conventional electronic system was used. The observed events were registered by the TAC method. The 55 Fe decays by electron capture process to the ground state of 55 Mn, emitting x rays with around 6 keV. The standardization was obtained by the tracing method. This technique was applied using two radionuclides, which decay by electron capture process followed by a prompt gamma-ray, namely 51 Cr and 54 Mn, as tracers. Measurements with 1 and 2 aluminum foils, each 150 g cm-2 thick were carried out. The activity was obtained by extrapolation for zero thickness Al foil. The uncertainties were treated by means of matrix covariance methodology and takes into account all correlations involved. (author)

Modulation spectroscopy study of the effects of growth interruptions on the interfaces of GaAsSb/GaAs multiple quantum wells

International Nuclear Information System (INIS)

Hsu, H P; Sitarek, P; Huang, Y S; Liu, P W; Lin, J M; Lin, H H; Tiong, K K

2006-01-01

The effects of growth interruption times combined with Sb exposure of GaAsSb/GaAs multiple quantum wells (MQWs) have been investigated by using phototransmittance (PT), contactless electroreflectance (CER) and wavelength modulated surface photovoltage spectroscopy (WMSPS). The features originated from different portions of the samples, including interband transitions of MQWs, interfaces and GaAs, are observed and identified through a detailed comparison of the obtained spectra and theoretical calculation. A red-shift of the interband transitions and a broader lineshape of the fundamental transition are observed from samples grown under Sb exposure compared to the reference sample grown without interruption. The results can be interpreted in terms of both increases in Sb content and mixing of Sb in the GaAs interface layers. An additional feature has been observed below the GaAs region in the samples with Sb treatment. The probable origin of this additional feature is discussed

Electrochemically produced alumina as TL detector

International Nuclear Information System (INIS)

Osvay, M.

1996-01-01

The goal of this work was to compare the TL properties of various electrochemically produced alumina layers (E-AIO) in order to investigate the effect of the electrolyte and the Mg content on the alloys. It has been found that the TL sensitivity of oxidised layers is more influenced by the type of electrolyte, than by the composition of alloy. Hard oxide layer evolved in reduction electrolyte has rather different character compared to other alumina production investigated. The effect of reducing media seems to be very important during preparation of alumina layer. One of the advantages properties of E-AIO is, that it serve a promising method to increase the measuring range of TL method above 10 kGy as well. (author)

Subsolidus phase relations of the SrO–SbOx–CuO system at 1140K in air

DEFF Research Database (Denmark)

Grivel, J.-C.; Norby, Poul; Andersen, Niels Hessel

2014-01-01

The subsolidus phase relations of the SrO–SbOx–CuO system were investigated in air. The samples were equilibrated at 1140K. Under these conditions, 7 binary oxide phases are stable: Sr2CuO3, SrCuO2, Sr14Cu24O41−δ, CuSb2O6, SrSb2O6, Sr2Sb2O7 and Sr7Sb2O12. The ternary section contains 10 three...

Structural and Electronic Features of Sb-Based Electrode Materials: 121Sb Moessbauer Spectrometry

International Nuclear Information System (INIS)

Ionica, C. M.; Aldon, L.; Lippens, P. E.; Morato, F.; Olivier-Fourcade, J.; Jumas, J.-C.

2004-01-01

Lithium insertion mechanisms in two antimony based compounds: CoSb 3 and CoSb have been studied by means of 121 Sb Moessbauer spectrometry. Structural and electronic modifications induced by insertion of lithium have been characterised for different depths of discharge. In all cases the insertion mechanisms can be described from several steps. In the first step antimony is partially dispersed in the metallic matrix with amorphisation of the electrode material and in a second step we can observe the alloy forming (Li 3 Sb). However this amorphous alloy remains in interaction with the matrix allowing then a good reversibility.

Photoemission study of the skutterudite compounds CoSb sub 3 and RhSb sub 3

CERN Document Server

Ishii, H; Fujimori, A; Nagamoto, Y; Koyanagi, T; Sofo, J O

2002-01-01

We have studied the electronic structure of the skutterudite compounds CoSb sub 3 and Co(Sb sub 0 sub . sub 9 sub 6 Te sub 0 sub . sub 0 sub 4) sub 3 by photoemission spectroscopy. Valence-band spectra revealed that a significant amount Sb 5p states are present near the Fermi level and are hybridized with Co 3d states just below it. The spectra are well reproduced by the band-structure calculation, suggesting that the effect of electron correlations is not important. When Te is substituted for Sb and n-type carriers are doped into CoSb sub 3 , the spectra are shifted to higher binding energies as described by the rigid-band model. From this shift and the free-electron model for the conduction and valence bands, we have estimated the band gap of CoSb sub 3 to be 0.03-0.04 eV, consistent with transport measurements. Photoemission spectra of RhSb sub 3 have also been measured and revealed expected similarities to and differences from those of CoSb sub 3. Unusual temperature dependence has been observed for the s...

Dating archeological ceramics from the Valley of Vitor, Arequipa by the TL method

Science.gov (United States)

Cano, N. F.; Arizaca, E. C.; Yauri, J. M.; Arenas, J. S. A.; Watanabe, S.

The age of some ancient pottery from the Valley of Vitor in the region of Arequipa, Peru, is determined by the thermoluminescence (TL) method. For dating, a 325 °C TL peak was used and irradiation with γ-dose from 5 to 50 Gy was carried out for the additive method, and from 0.4 to 5 Gy for the regeneration method. For these dose values, the TL intensity is observed to grow linearly, obtaining an accumulated dose of 1.62±0.09 Gy and 1.36±0.03 Gy for the additive and regeneration methods, respectively. The age (A) of the sample was calculated by the two methods, being A=867±195 years after Christ (AC) for the additive method and A=1050±157 years AC for the regeneration method. Both results are within 800-1200 years AC, which is the period of the Wari culture.

Pulse shaper for scintillation detectors with NaI(Tl) or CsI(Tl) crystals

International Nuclear Information System (INIS)

Novisov, B.S.; Maksimenko, A.S.; Baryshev, A.V.; Zhukov, A.V.

1978-01-01

The basic circuit of a signal shaper for scintillation detectors with NaI(Tl) and CsI(Tl) crystals is described. To increase amplitude resolution, it is suggested to integrate not the whole charge at the photomultiplier output, but a part of the charge during the initial 100 ns of the current pulse; the remaining part of the current signal is compensated directly at the photomultiplier anode by means of an electric circuit. The principal elements of the spectrometric signal shaper include an input transistor amplifier, a compensation circuit, a key element, a shaper amplifier of time pulses, a shaper of signal duration for controlling the key element, and an output spectrometric amplifier. This device, being used, one can shape pulses at durations of 100 ns and more. The shaper restoration time does not exceed 50 ns. When the shaper operates with NaI(Tl) crystals and at counting rate of 10 6 pulse/s, the amplitude resolution with and without the compensation circuit is 17% and 21% respectively

Alpha efficiency under TL and OSL - A subtraction technique using OSL and TL to detect artificial irradiation

International Nuclear Information System (INIS)

Zink, A.J.C.; Dabis, S.; Porto, E.; Castaing, J.

2010-01-01

With the development of thermoluminescence (TL) and optically stimulated luminescence (OSL) to determine the authenticity of old ceramics, forgers use artificial irradiation by gamma ray to age modern productions. Besides fraudulent action, objects can be exposed to various sources of X-rays (e.g. radiography, security control at airports). For all these reasons, the determination of artificial irradiation is an important topic for dating art objects. The main technique to identify artificial irradiations is the subtraction technique. It is based on the fact that alpha efficiency varies according to the luminescence technique (fine grain, coarse grains, predose, OSL). Having observed a rather significant difference of alpha efficiency for TL and OSL, we propose a new subtraction technique using OSL and TL of fine grains.

TL and OSL studies on undoped diamond films grown by hot filament chemical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Soni, Anuj, E-mail: anujsoni.phy@gmail.com [Radiological Physics and Advisory Division, Bhabha Atomic Research Center, Mumbai 400 085 (India); Choudhary, R.K. [Materials Processing Division, Bhabha Atomic Research Center, Mumbai 400 085 (India); Polymeris, G.S. [Ankara University, Institute of Nuclear Sciences (Turkey); Mishra, D.R. [Radiological Physics and Advisory Division, Bhabha Atomic Research Center, Mumbai 400 085 (India); Mishra, P. [Materials Processing Division, Bhabha Atomic Research Center, Mumbai 400 085 (India); Kulkarni, M.S. [Radiation Safety Systems Division, Bhabha Atomic Research Center, Mumbai 400 085 (India)

2016-09-15

In this work, approximately 0.5 µm thick diamond films were grown on a silicon substrate by hot filament chemical vapour deposition (HFCVD) method in a gas mixture of hydrogen and methane. The batch to batch reproducibility of the sample using this technique was found to be very good. The obtained film was characterized by micro laser Raman spectroscopy (MLRS), grazing incidence X-ray diffractometry (GIXRD), scanning electron microscopy (SEM) and atomic force miscroscopy (AFM) techniques. MLRS and GIXRD results confirmed the formation of diamond whereas SEM and AFM analyses indicated uniform morphology of the film with an average grain size of 200 nm. The deposited film was studied for ionizing radiation dosimetry applications using the thermoluminescence (TL) and optically stimulated luminescence (OSL) techniques after irradiating the film by a calibrated 5 mCi, {sup 90}Sr/{sup 90}Y beta source. In the TL measurement, for a heating rate of 4 K/s, broad glow curve was obtained which was deconvoluted into seven TL peaks. The integrated TL counts were found to vary linearly with increasing the radiation dose up to 10 kGy. The characteristic TL output seen in the temperature range 200–300 °C, may be considered good for thermal stability of the film and it could also avoid TL fading during storage and non-interference of any black body radiation during the measurement. However, in comparison to TL output, the OSL response for 470 nm LED stimulation was found to be lesser. The CW–OSL decay curve has shown two components contributing to the OSL signal, having photoionization cross-section 1.5×10{sup −18} and 5.2×10{sup −19} cm{sup 2} respectively. The studies have revealed the possibility of using diamond film for high dose radiation dosimetry with TL/OSL method.

Electrodeposition and electrochemical characterisation of thick and thin coatings of Sb and Sb/Sb2O3 particles for Li-ion battery anodes

International Nuclear Information System (INIS)

Bryngelsson, Hanna; Eskhult, Jonas; Edstroem, Kristina; Nyholm, Leif

2007-01-01

The possibilities to electrodeposit thick coatings composed of nanoparticles of Sb and Sb 2 O 3 for use as high-capacity anode materials in Li-ion batteries have been investigated. It is demonstrated that the stability of the coatings depends on their Sb 2 O 3 concentrations as well as microstructure. The electrodeposition reactions in electrolytes with different pH and buffer capacities were studied using chronopotentiometry and electrochemical quartz crystal microbalance measurements. The obtained deposits, which were characterised with XRD and SEM, were also tested as anode materials in Li-ion batteries. The influence of the pH and buffer capacity of the deposition solution on the composition and particle size of the deposits were studied and it is concluded that depositions from a poorly buffered solution of antimony-tartrate give rise to good anode materials due to the inclusion of precipitated Sb 2 O 3 nanoparticles in the Sb coatings. Depositions under conditions yielding pure Sb coatings give rise to deposits composed of large crystalline particles with poor anode stabilities. The presence of a plateau at about 0.8 V versus Li + /Li due to SEI forming reactions and the origin of another plateau at about 0.4 V versus Li + /Li seen during the lithiation of thin Sb coatings are also discussed. It is demonstrated that the 0.4 V plateau is present for Sb coatings for which the (0 1 2) peak is the main peak in the XRD diffractogram

Remote TL and OSL for asteroid and meteorite study

International Nuclear Information System (INIS)

Takaki, Shunji; Ikeya, Motoji; Yamanaka, Chihiro

1997-01-01

Thermoluminescence (TL) and optically stimulated luminescence (OSL) of the Allende meteorite have been studied using infrared CO 2 laser light as a heat source and He-Ne laser light to excite the material, respectively from a long distance. New techniques of remote TL (R-TL) and remote OSL (R-OSL) have been developed for future remote dating from a long distance in a planetary survey. The upper limits of the distance for R-TL and R-OSL were estimated using the laboratory TL signal of the meteorite peaking at 320 o C: about 400 photons s -1 for the R-TL and 60 photons s -1 for R-OSL at a distance of 1 km using a laser beam with the divergence of 0.1 mrad at powers of 100 and 1 W, respectively. An age limit of 10 5 or 10 6 years due to the signal saturation and the objects heterogeneity, as expected from previous studies, may make the asteroid survey difficult but would still help to investigate the surface activities of icy planets and satellites in outer planet worlds. (author)

[Sb{sub 4}Au{sub 4}Sb{sub 4}]{sup 2−}: A designer all-metal aromatic sandwich

Energy Technology Data Exchange (ETDEWEB)

Tian, Wen-Juan; You, Xue-Rui [Nanocluster Laboratory, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China); Guo, Jin-Chang [Department of Chemistry, Xinzhou Teachers University, Xinzhou 034000 (China); Li, Da-Zhi, E-mail: hj.zhai@sxu.edu.cn, E-mail: ldz005@126.com [Department of Chemical Engineering, Binzhou University, Binzhou 256603 (China); Wang, Ying-Jin [Nanocluster Laboratory, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China); Department of Chemistry, Xinzhou Teachers University, Xinzhou 034000 (China); Sun, Zhong-Ming [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zhai, Hua-Jin, E-mail: hj.zhai@sxu.edu.cn, E-mail: ldz005@126.com [Nanocluster Laboratory, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China); State Key Laboratory of Quantum Optics and Quantum Optics Devices, Shanxi University, Taiyuan 030006 (China)

2016-07-28

We report on the computational design of an all-metal aromatic sandwich, [Sb{sub 4}Au{sub 4}Sb{sub 4}]{sup 2−}. The triple-layered, square-prismatic sandwich complex is the global minimum of the system from Coalescence Kick and Minima Hopping structural searches. Following a standard, qualitative chemical bonding analysis via canonical molecular orbitals, the sandwich complex can be formally described as [Sb{sub 4}]{sup +}[Au{sub 4}]{sup 4−}[Sb{sub 4}]{sup +}, showing ionic bonding characters with electron transfers in between the Sb{sub 4}/Au{sub 4}/Sb{sub 4} layers. For an in-depth understanding of the system, one needs to go beyond the above picture. Significant Sb → Au donation and Sb ← Au back-donation occur, redistributing electrons from the Sb{sub 4}/Au{sub 4}/Sb{sub 4} layers to the interlayer Sb–Au–Sb edges, which effectively lead to four Sb–Au–Sb three-center two-electron bonds. The complex is a system with 30 valence electrons, excluding the Sb 5s and Au 5d lone-pairs. The two [Sb{sub 4}]{sup +} ligands constitute an unusual three-fold (π and σ) aromatic system with all 22 electrons being delocalized. An energy gap of ∼1.6 eV is predicted for this all-metal sandwich. The complex is a rare example for rational design of cluster compounds and invites forth-coming synthetic efforts.

Studies on the tumor and organ affinity of /sup 201/Tl

Energy Technology Data Exchange (ETDEWEB)

Mori, H; Ando, I; Takeuchi, T [Kanazawa Univ. (Japan). School of Medicine; Ando, A; Hiraki, T

1980-01-01

In order to evaluate the tumor and organ affinity of /sup 201/Tl, using the Yoshida sarcoma bearing rats, the distribution of /sup 201/Tl/sup +/ in tissues and tumor was examined and compared to /sup 22/Na/sup +/, /sup 42/K/sup +/, /sup 86/Rb/sup +/, /sup 134/Cs/sup +/, and /sup 67/Ga-citrate. /sup 201/Tl/sup +/ showed almost same organ accumulation and kinetics as /sup 42/K/sup +/, /sup 86/Rb/sup +/, /sup 134/Cs, whereas /sup 201/Tl/sup +/ and /sup 22/Na/sup +/ had completely different organ distribution. These results suggest that organ affinity of /sup 201/Tl/sup +/ might be related to active transport, namely Na/sup +/-K/sup +/-ATPase pump mechanism as well as blood flow. However, it appeared to be taken into account the other factors such as different accumulation and clearance rate due to different substrates of organs. Kidney accumulation rate of /sup 201/Tl/sup +/ was much higher than /sup 42/K/sup +/, /sup 86/Rb/sup +/, /sup 134/Cs/sup +/ and about 10 times as /sup 42/K/sup +/. Macroautoradiograms of rat kidneys showed that /sup 201/Tl/sup +/ exhibited an initial high accumulation in the cortex and appeared in the outer cortex, as the cortex cleared of radioactivity. /sup 201/Tl might be interchangeable with K/sup +/ in the tubular system, reabsorbed with more affinity and cleared more slowly than K/sup +/. The tumor accumulation /sup 201/Tl/sup +/ might be related to Na/sup +/-K/sup +/-ATPase pump mechanism as well as other organs. However, in terms of tumor accumulation and concentration ratio to other organs, /sup 201/Tl/sup +/ was inferior to /sup 67/Ga-citrate, although the tumor to blood ratio was identical to that of /sup 67/Ga-citrate. Since /sup 201/Tl/sup + + +/ showed almost same distribution as /sup 201/Tl/sup +/, /sup 201/Tl/sup + + +/ might change into /sup 201/Tl/sup +/ in vivo.

Two new examples of very short thallium-transition metal contacts

DEFF Research Database (Denmark)

Karanovic, Ljiljana; Poleti, Dejan; Balic Zunic, Tonci

2008-01-01

Two new sulphosalts Tl3Ag3Sb2S6, (1) and Tl(3)Ag(3)AS(2)S(6), (2) were prepared in reaction of synthetic binary sulfides: argentite (Ag2S), carlinite (Tl2S) and orpiment (As2O3) or stibnite (Sb2S3), and their crystal structures have been determined using single-crystal data. The compounds are iso....... It is also pointed out that if only valence shell electrons are considered (Tl-Ag)(2+) group is isoelectronic with the (Hg-Hg)(2+) ion, therefore new examples of short Tl-Ag contacts could be expected. (C) 2007 Elsevier B.V. All rights reserved....

Persistent luminescence, TL and OSL characterization of beta irradiated SrAl2O4:Eu2+, Dy3+ combustion synthesized phosphor

International Nuclear Information System (INIS)

Zúñiga-Rivera, N.J.; García, R.; Rodríguez-Mijangos, R.; Chernov, V.; Meléndrez, R.; Pedroza-Montero, M.; Barboza-Flores, M.

2014-01-01

The persistent luminescence (PLUM), thermoluminescence (TL) and optically stimulated luminescence (OSL) properties of strontium aluminates co-doped with Eu +2 and Dy +3 exposed to beta radiation is reported. The phosphor was synthesized by the combustion synthesis method employing a highly exothermic redox reaction between the metal nitrates [Al(NO 3 ) 3 , Sr(NO 3 ) 2 , Eu(NO 3 ) 3 and Dy(NO 3 ) 3 ] and organic fuel carbohydrazide (CH 6 N 4 O). The long decay PLUM emission, TL and OSL were measured as a function of beta radiation dose. A wide emission band centered at 510 nm (green) related to Eu 2+ ions and lattice defects were observed for the synthesized samples. The presence of a variety of defects and aggregates were responsible for the observed broad 100 °C peaked TL glow curve of the irradiated sample which is composed of several overlapped TL peaks. The existence of multiple trapping levels, with different trapping/detrapping probabilities, is behind the particular features for the PLUM, TL and OSL emissions. We conclude that in the SrAl 2 O 4 :Eu 2+ , Dy 3+ phosphors, the low temperature TL peaked around 30–75 °C is responsible for the PLUM emission and those around 100 °C were related to very stable trapping states which provide suitable radiation storage properties to be used as a PLUM/TL/OSL radiation phosphor

TL Dating Technique Based on a Trap Model and its Application as a Geochronometer for Granitic Quartz

International Nuclear Information System (INIS)

Han, Y.; Li, H.; Tso, Y.W.

1999-01-01

A trap model is introduced to describe the behaviours of both thermally sensitive and radiation sensitive TL traps. The former are relatively shallow traps. The latter are deep traps, in which population increases with exposure to alpha dose. Thermal decay of both types of traps at ambient temperature is dependent on the trap lifetimes. A trap's population can be measured as TL sensitivity to a laboratory test dose. The trap model has been supported by observations of age dependent TL signals from granitic quartz samples with different crystallisation ages. The trap lifetimes are from 1.98 x 10 9 to 5.36 x 10 15 years estimated using the isothermal decay experiment with the assumption of first order kinetics. Dating techniques are proposed based on the trap model. For old granites (>400 Ma), ages can be obtained by measuring the total exposed alpha dose using the additive alpha dose method, whereas for young granites (<400 Ma), ages can also be obtained by interpolating the TL sensitivity to a curve of TL sensitivities for known ages. (author)

In As{sub 1–x}Sb{sub x} heteroepitaxial structures on compositionally graded GaInSb and AlGaInSb buffer layers

Energy Technology Data Exchange (ETDEWEB)

Guseynov, R. R.; Tanriverdiyev, V. A. [National Academy of Sciences of Azerbaijan, Institute of Physics (Azerbaijan); Kipshidze, G., E-mail: gela.kishidze@stonybrook.ede [Stony Brook, Stony Brook University (United States); Aliyeva, Ye. N.; Aliguliyeva, Kh. V.; Abdullayev, N. A., E-mail: abnadir@mail.ru; Mamedov, N. T. [National Academy of Sciences of Azerbaijan, Institute of Physics (Azerbaijan)

2017-04-15

Unrelaxed InAs{sub 1–x}Sb{sub x} (x = 0.43 and 0.38) alloy layers are produced by molecular-beam epitaxy on compositionally graded GaInSb and AlGaInSb buffer layers. The high quality of the thin films produced is confirmed by the results of high-resolution X-ray diffraction analysis and micro-Raman studies. The twomode type of transformation of the phonon spectra of InAs{sub 1–x}Sb{sub x} alloys is established.

Direct synthesis of Sb{sub 2}O{sub 3} nanoparticles via hydrolysis-precipitation method

Energy Technology Data Exchange (ETDEWEB)

Hu, Yuehua [Department of Inorganic Materials, School of Resources Processing and Bioengineering, Central South University, Changsha 410083 (China); Zhang, Huihui [Department of Inorganic Materials, School of Resources Processing and Bioengineering, Central South University, Changsha 410083 (China); Yang, Huaming [Department of Inorganic Materials, School of Resources Processing and Bioengineering, Central South University, Changsha 410083 (China)]. E-mail: hmyang@mail.csu.edu.cn

2007-01-31

Antimony oxide (Sb{sub 2}O{sub 3}) has wide applications as conductive materials, effective catalyst, functional filler and optical materials. Nanocrystalline Sb{sub 2}O{sub 3} has been successfully synthesized by hydrolysis-precipitation method. The samples were characterized by means of transmission electron microscopy (TEM), high-resolution TEM (HRTEM) images, X-ray diffraction (XRD) and differential thermal analysis (DTA). The average crystal size of the Sb{sub 2}O{sub 3} nanoparticles increases with increasing the reaction temperature. TEM image of the as-synthesized nanocrystalline Sb{sub 2}O{sub 3} shows rod-like structure. HRTEM images indicate a preferred directional growth of the Sb{sub 2}O{sub 3} nanoparticles. The electrochemical behaviors of Sb{sub 2}O{sub 3} electrodes have been primarily investigated by cyclic voltammetry (CV) in lithium hexafluorophosphate (LiPF{sub 6}) solution. Sb{sub 2}O{sub 3} nanocrystallite phase has prominent effect on the electrochemical properties. The results indicate that nanocrystalline Sb{sub 2}O{sub 3} synthesized by hydrolysis-precipitation method shows potential application in the field of the electrode materials.

TL and OSL properties of Mn2+-doped MgGa2O4 phosphor

Science.gov (United States)

Luchechko, A.; Zhydachevskyy, Ya; Maraba, D.; Bulur, E.; Ubizskii, S.; Kravets, O.

2018-04-01

The oxide MgGa2O4 spinel ceramics doped with Mn2+ ions was synthesized by a solid-state reaction at 1200 °C in air. The activator concentration was equal 0.05 mol% of MnO. Phase purity of the synthesized samples was analyzed by X-ray diffraction technique. This spinel ceramics show efficient green emission in the range from 470 to 550 nm with a maximum at about 505 nm under UV or X-ray excitations, which is due to Mn2+ ions. MgGa2O4: Mn2+ exhibits intense thermoluminescence (TL) and optically stimulated luminescence (OSL) after influence of ionizing radiation. Are complex nature of the TL glow curves is associated with a significant number of structural defects that are responsible for the formation of shallow and deep electron traps. In this work, time-resolved OSL characteristics of the samples exposed to beta particles are reported for the first time. A light from green LED was used for optical stimulation. Obtained TL and OSL results suggest MgGa2O4:Mn2+ as perspective material for further research and possible application in radiation dosimetry.

Magnetic properties of CeyFe4-xNixSb12

International Nuclear Information System (INIS)

Viennois, R.; Ravot, D.; Tedenac, J.C.; Charar, S.; Mauger, Alain

2005-01-01

The structural and magnetic properties of the metallic skutterudite CeFe 4 Sb 12 have been investigated, with those of Ce y Fe 4-x Ni x Sb z with compositions approaching the relations y=(4-2x)/3, z=12 for which the materials are semiconductors. The large and temperature-dependent contribution of Fe to the magnetic susceptibility of CeFe 4 Sb 12 has been isolated from the Ce contribution, which makes possible a quantitative analysis of the Kondo lattice behavior. In CeFe 4 Sb 12 the Wilson-Sommerfeld ratio is modified by a factor two with respect to former analyses where the magnetic contribution of Fe had been neglected. The main effect of the reduction of the free carrier (hole) concentration in Ce y Fe 4 Sb 12 is to suppress the Kondo effect and the Fe contribution to the magnetic susceptibility. The samples with theoretical hole concentration per unit cell p*=z-8-3y-2x smaller than 0.5 behave like semiconductors in which the exchange between localized Ce 3+ spins is negligible, and are most promising for a potential use as thermoelements

Adducts of UF5 with SbF5 and structure of UF5 . 2SbF5

International Nuclear Information System (INIS)

Sawodny, W.; Rediess, K.

1980-01-01

Both α-UF 5 and β-UF 5 form only a 1:2 compound UF 5 . 2SbF 5 reacting directly with SbF 5 , from which UF 5 . SbF 5 can be obtained by thermal decomposition. UF 5 . 2SbF 5 crystallizes in the monoclinic space group P2 1 /c with the following lattice constants a = 8.110(4), b = 14.129(6), c = 10.032(6) A and β = 96.97(5) 0 ; Z = 4. An X-ray study shows centrosymmetric four-membered rings of alternating UF 8 and SbF 6 polyhedra connected by other SbF 6 entities. This structure is similar to that of UOF 5 . 2SbF 5 , but the distorted pentagonal-bipyramidal coordination of the U atom found there is increased to a dodecahedral coordination by an additional U-F-Sb bridge, though with a somewaht larger UF distance. (author)

The superconductor (Tl,Hg,Ca)2(Ba,Sr)2(Ca,Sr,Tl)Cu2O7.6

International Nuclear Information System (INIS)

Valldor, M.; Bryntse, I.; Morawski, A.

2002-01-01

In the title 2212-type superconductor (thallium mercury calcium barium strontium copper oxide), which contains both Tl and Hg in the charge reservoir (CR), Sr is located at both alkali-earth (AE) metal sites. Ca enters the CR at the same time as Tl shares the smaller AE site, which increases the apical Cu-Cu distance significantly. The structure causes the superconducting Cu-O layers to become significantly puckered. (orig.)

Study of conformational changes and protein aggregation of bovine serum albumin in presence of Sb(III) and Sb(V).

Science.gov (United States)

Verdugo, Marcelo; Ruiz Encinar, Jorge; Costa-Fernández, José Manuel; Menendez-Miranda, Mario; Bouzas-Ramos, Diego; Bravo, Manuel; Quiroz, Waldo

2017-01-01

Antimony is a metalloid that affects biological functions in humans due to a mechanism still not understood. There is no doubt that the toxicity and physicochemical properties of Sb are strongly related with its chemical state. In this paper, the interaction between Sb(III) and Sb(V) with bovine serum albumin (BSA) was investigated in vitro by fluorescence spectroscopy, and circular dichroism (CD) under simulated physiological conditions. Moreover, the coupling of the separation technique, asymmetric flow field-flow fractionation, with elemental mass spectrometry to understand the interaction of Sb(V) and Sb(III) with the BSA was also used. Our results showed a different behaviour of Sb(III) vs. Sb(V) regarding their effects on the interaction with the BSA. The effects in terms of protein aggregates and conformational changes were higher in the presence of Sb(III) compared to Sb(V) which may explain the differences in toxicity between both Sb species in vivo. Obtained results demonstrated the protective effect of GSH that modifies the degree of interaction between the Sb species with BSA. Interestingly, in our experiments it was possible to detect an interaction between BSA and Sb species, which may be related with the presence of labile complex between the Sb and a protein for the first time.

Magnetic and structural properties of Bi(2223doped by pb and Sb

Directory of Open Access Journals (Sweden)

H. Salamati

1998-04-01

Full Text Available   In a systematic approach, we have investigated the effect of the presence of Pb and Sb in the Bi site in a BSCCO (2223 phase superconductor. There are some contradictory reports in substitution of Sb in the Bi site. Some researchers report an increase in the Tc of these materials. So, we have made an accurate stoichiometry of these superconductors and selected extra pure starting materials with appropriate ratios of Pb+Sb.   The susceptility of these samples have been measured and the structures of the systems have been studied by SEM and XRD. The results of this investigation show that, Although the presence of Pb is essential for formation of (2223 phase, but addition of small amount of Sb helps to stabilize and enhance the ratio of higher phase. Our results show that, presence of Sb would raise the critical current density, but would not affect the Tc of these superconductors.

Simultaneous speciation and preservation of aqueous As, Sb and Se redox couples

Science.gov (United States)

Wu, D.; Pichler, T.

2014-12-01

We developed a new method for the simultaneous speciation analysis of inorganic arsenic (III, V), antimony (III, V) and selenium (IV, VI) in water samples via double-focusing sector field-inductively coupled plasma-mass spectrometry (SF-ICP-MS) coupled to high performance liquid chromatography (HPLC). A Hamilton PRX-X100 anion exchange column with EDTA (pH of 4.7) and 3% methanol as mobile phase was used for species separation. The flow rate was set to 1.5 mL min-1 and a solvent gradient (linear ramp from 5 mM to 30 mM) was applied. The overall analysis time for all six desired species was 11 minutes. The detection limits for As(III), As(V), Sb(III), Sb(V), Se(VI) and Se(IV) were 0.02 μg L-1, 0.06 μg L-1, 0.2 μg L-1, 0.02 μg L-1, 0.2 μg L-1 and 0.4 μg L-1 respectively. The retention times for As(III), As(V), Sb(III), Sb(V), Se(IV) and Se(VI) were 1.70, 2.94, 7.14, 2.28, 3.38 and 9.36 min, respectively. Subsequently, the stability of inorganic As(III, V), Sb(III, V) and Se(IV, VI) species in different water samples (groundwater, lake water and river water) was studied over a time scale of 11 weeks. High concentrations of Fe (25.0 mg/L) and Mn (25.0 mg/L) were added to different matrices to simulate Fe and Mn rich environments. All samples were spiked with 5.0 μg/L As(III, V) and Sb(III, V) and 15.0 μg/L Se(IV, VI).. We investigated several strategies for species preservation, i.e., EDTA only, EDTA combined with acidification (HCl, HNO3, formic acid and acetic acid). The preserved samples were stored at 4 °C in the dark. For comparison, another subsample without any preservation was stored at room temperature in the presence of light. The results showed that a combination EDTA acidified to pH of 3 can be used to preserve all species for at least 11 weeks. While EDTA only (pH = 6) failed to preserve As and Sb species, although Se species were preserved.

205Tl experiment

International Nuclear Information System (INIS)

Henning, W.; Kutschera, W.; Ernst, H.

1984-01-01

205 Tl has been previously proposed as a geological detector for solar neutrinos, making use of the reaction 205 Tl(nu, e - ) 205 Pb with a neutrino threshold of only approx. = 43 keV. We report on an experiment performed to study the feasibility of detecting radioactive 205 Pb nuclei (T/sub 1/2/ = 15 million years) at very low concentrations using the recently developed technique of accelerator mass spectrometry. Employing the high-energy ion beams of good quality from the UNILAC heavy-ion accelerator at the GSI Darmstadt, we are able to demonstrate a suppression of neighbouring isotopes to better than 1 in 10 16 and of neighbouring elements to about 1 in 10 3 . While these results are very encouraging, the minimum number of atoms detectable is still severely limited by the efficiency of producing multiply-charged ions from present ion sources. Future improvements in ion-source performance are briefly discussed

Detailed α -decay study of 180Tl

Science.gov (United States)

Andel, B.; Andreyev, A. N.; Antalic, S.; Barzakh, A.; Bree, N.; Cocolios, T. E.; Comas, V. F.; Diriken, J.; Elseviers, J.; Fedorov, D. V.; Fedosseev, V. N.; Franchoo, S.; Ghys, L.; Heredia, J. A.; Huyse, M.; Ivanov, O.; Köster, U.; Liberati, V.; Marsh, B. A.; Nishio, K.; Page, R. D.; Patronis, N.; Seliverstov, M. D.; Tsekhanovich, I.; Van den Bergh, P.; Van De Walle, J.; Van Duppen, P.; Venhart, M.; Vermote, S.; Veselský, M.; Wagemans, C.

2017-11-01

A detailed α -decay spectroscopy study of 180Tl has been performed at ISOLDE (CERN). Z -selective ionization by the Resonance Ionization Laser Ion Source (RILIS) coupled to mass separation provided a high-purity beam of 180Tl. Fine-structure α decays to excited levels in the daughter 176Au were identified and an α -decay scheme of 180Tl was constructed based on an analysis of α -γ and α -γ -γ coincidences. Multipolarities of several γ -ray transitions deexciting levels in 176Au were determined. Based on the analysis of reduced α -decay widths, it was found that all α decays are hindered, which signifies a change of configuration between the parent and all daughter states.

Impact of precursor purity on optical properties and radiation detection of CsI:Tl scintillators

Energy Technology Data Exchange (ETDEWEB)

Saengkaew, Phannee; Cheewajaroen, Kulthawat; Yenchai, Chadet; Thong-aram, Decho [Chulalongkorn University, Department of Nuclear Engineering, Faculty of Engineering, Bangkok (Thailand); Sanorpim, Sakuntam [Chulalongkorn University, Department of Physics, Faculty of Science, Bangkok (Thailand); Jitpukdee, Manit [Kasetsart University, Department of Applied Radiation and Isotope, Faculty of Science, Bangkok (Thailand); Yordsri, Visittapong; Thanachayanont, Chanchana [Ministry of Science and Technology, National Metal and Materials Technology Center, National Science and Technology Development Agency, Pathumthani (Thailand); Nuntawong, Noppadon [Ministry of Science and Technology, National Electronic and Computer Technology Center, National Science and Technology Development Agency, Pathumthani (Thailand)

2016-08-15

Cesium iodide doped with thallium (CsI:Tl) crystals was grown to develop the gamma-ray detectors by using low-cost raw materials. Effect of impurities on optical properties and radiation detection performance was investigated. By a modified homemade Bridgman-Stockbarger technique, CsI:Tl samples were grown in two levels of CsI and TlI reactant materials, i.e., having as a very high purity of 99.999 % and a high purity of 99.9 %. XRD measurements indicate CsI:Tl crystals having a good quality with a dominant (110) plane. Having a cubic structure, a lattice constant of CsI crystals of 0.4574 nm and a crystallite size of 43.539 nm were obtained. From the lower-purity raw materials, calcite was found in an orange crystal with a lattice constant of 0.4560 nm and a crystallite size of 43.089 nm. By PL measurements, the optical properties of the CsI:Tl crystals were analyzed. ∝540-nm-wavelength PL peak was observed from the colorless high-purity crystal, and ∝600-nm-wavelength PL peak was observed from the orange crystal. The brighter PL emission was obtained from the orange crystals suggesting impurities. CsI:Tl surface morphology by SEM exhibited a smooth surface with some parallel crystal facets. For electrical properties of high-quality CsI:Tl crystals, the electrical resistances were 230 ± 16 MΩ in cross-sectional direction and 714 ± 136 MΩ in vertical direction with respect to more homogeneous crystal quality in cross-sectional direction than that in vertical direction. TEM measurement was applied to evaluate the microstructure of colorless CsI:Tl crystal with different patterns of a cubic structure. Both CsI:Tl crystals show good efficiencies and good resolutions. Maintaining the same electronic conditions and amplifications, the colorless CsI:Tl scintillators represented a higher detection efficiency at 122 keV of Co-57 of 78.4 % and the energy resolution of 23.3 % compared to the detection efficiency of 75.9 % and the energy resolution of 34.6 % of the

OSL and TL retrospective dosimetry with a fluorapatite glass-ceramic used for dental restorations

International Nuclear Information System (INIS)

Ekendahl, Daniela; Judas, Libor; Sukupova, Lucie

2013-01-01

Optically Stimulated Luminescence (OSL) and Thermoluminescence (TL) properties of a fluorapatite glass-ceramic have been investigated, with a view to developing a dose assessment technique for medical triage following unplanned exposures of individuals to ionizing radiation. The ceramic is an innovative material used in dental prostheses and restorations. It is strongly sensitive to radiation and the intensity of both the OSL and TL signals are proportional to the absorbed radiation dose. We focused on the optimization of the measuring procedure and investigated characteristics such as reproducibility, fading, minimum detectable dose (MDD), dose response and photon energy response of TL and OSL signals. The dental ceramic exhibited very good reproducibility (<5% at 2σ level) when measured and a linear dose response for a wide range of doses (50 mGy–20 Gy). The MDD values for the samples investigated were ∼5 mGy. The material is not tissue equivalent and the OSL and TL signals are strongly dependent on incident photon energy. Both the luminescence signals exhibited significant fading during the first few hours after irradiation. Its rate was dependent on the parameters of measurement. The results indicate that the material can be used for the purposes of accident dosimetry, however, the fading and photon energy response have to be properly corrected for a reliable dose assessment. - Highlights: ► A dental ceramic was considered as a retrospective and accident dosimeter. ► Dosimetry application was investigated using OSL and TL. ► TL and OSL signals are proportional to absorbed radiation dose. ► Accuracy is dependent on correction of fading and photon energy response

Can iron plaque affect Sb(III) and Sb(V) uptake by plants under hydroponic conditions

NARCIS (Netherlands)

Ji, Ying; Lenz, Markus; Lenz, Markus; Schulin, Rainer; Tandy, Susan

2018-01-01

Antimony (Sb) contamination of soils is of concern due to h uman activities such as recycling of Sb containing Pb acid batteries, shooting and mining. However Sb uptake by plants is poorly documented, especially when plants are growing on waterlogged soils and iron plaques form on their roots. The

The adsorption of Tl(I), Au(III), Cu(II) and the separation of 199Tl from alpha bombardment of gold target with PDB-18C6

International Nuclear Information System (INIS)

Zhou Dehai; Zhou Jimeng

1989-01-01

The adsorptive behavior of polymer of methyl aldehyde of dibenzo-18-crown-6 (PDB-18C6) in hydrochloric acid medium is studied and it is shown that the adsorption of T1(I), Au(III), and Cu(II) depends on the particle size of the crown ether resins, hydrochloric acid concentration and amount of the crown ether resins used. The difference in the adsorption behavior of different particle sizes of crown ether resins may be used for separating Tl(I), Au(III), and Cu(II) ions. The best eluant of Tl(I) and Au(III) is 0.4 mol/l perchloric acid and 2-ethoxy-ethanol. The recovery for Tl(I) is 82-98.8%. The gold target is bombarded in a 1.2 m cyclotron with 25-27 MeV α-particle with a cumulative beam intensities of 27μA·h, and 199 Tl is separated from the gold target with PDB-18C6. γ-spectrometry has shown that the Tl obtained is 199 Tl of high purity containing only about 0.50% 200 Tl

Development of surgical gamma probes with TlBr semiconductors and CsI(Tl) scintillators crystals

International Nuclear Information System (INIS)

Costa, Fabio Eduardo da

2006-01-01

Radio guided surgery, using probes with radiation detectors, has been prominence in the medical area in the last decade. This technique consists in injecting a radioactive substance to concentrate in tumour and assist the localization during the surgical procedure. The radio guided surgeries allowing the identification of lymph node has revolutioned the behavior of tumour in initial stadium when are being spread by lymphatic way. The conditions imposed to the surgery due the proximity between some lymph nodes, demands of the probes, a small diameters and capacity of individual identification of these lymph nodes radiolabelled by a specific tracer. The international market supplies these probes with CdTe semiconductors and scintillators, but there is some time lack a promptly technical assistance in the Brazilian market. This work developed probes with national technology, using CsI(Tl) scintillators crystals and, in substitution to CdTe crystals semiconductors, the TlBr crystal, that is a new semiconductor detector in a world-wide development, with advantages in relation to the CdTe. Both crystals have been grown in IPEN. All the necessary electronics, specially, the preamplifier, that was also a restrictive factor for development of these types of probe in the country, have been developed with components found in the national market. Systematic measures of spatial resolution, spatial selectivity, maximum sensitivity and quality of the shielding have been carried the probes development. The results have shown that the probes, one with the CsI(Tl) crystal and another with TlBr semiconductor presented the requested performance in the international literature for radio guided probes. (author)

How Experienced SoTL Researchers Develop the Credibility of Their Work

Directory of Open Access Journals (Sweden)

Jennie Billot

2017-03-01

Full Text Available Teaching and learning research in higher education, often referred to as the Scholarship of Teaching and Learning (SoTL, is still relatively novel in many academic contexts compared to the mainstay of disciplinary research. One indication of this is the challenges those who engage in SoTL report in terms of how this work is valued or considered credible amongst disciplinary colleagues and in the face of institutional policies and practices. This paper moves beyond the literature that describes these specific challenges to investigate how 23 experienced SoTL researchers from five different countries understood the notion of credibility in relationship to their SoTL research and how they went about developing credibility for their work. Semi-structured interviews were facilitated and analyzed using inductive analysis. Findings indicate that notions of credibility encompassed putting SoTL research into action and building capacity and community around research findings, as well as gaining external validation through traditional indicators such as publishing. SoTL researchers reported a variety of strategies and approaches they were using, both formal and informal, to develop credibility for their work. The direct focus of this paper on credibility of SoTL work as perceived by experienced SoTL researchers, and how they go about developing credibility, is a distinct contribution to the discussions about the valuing of SoTL work.

Effect of stress on the superconducting transition temperature in indium, indium-alloy, tin, and tin-alloy whisker samples

International Nuclear Information System (INIS)

Cook, J.W. Jr.; Davis, W.T.; Chandler, J.H.; Skove, M.J.

1977-01-01

The dependence of the superconducting transition temperature (T/sub c/) on stress (sigma) for pure In and Sn samples was found to be in qualitative agreement with earlier work. For convenience T/sub c/ is expressed as a function of the experimentally measured strain (epsilon), which is proportional to sigma. The effect of alloying on the initial dependence of the T/sub c/-vs-epsilon curves, (per. delta T/sub c//per. delta epsilon)/sub epsilon = 0/ = eta, was quite different for the In and Sn alloys. The In samples were alloyed with a maximum of 4.8 at.% Tl, 7.9 at.% Sn, and 6.7 at.% Pd; the Sn samples were alloyed with a maximum of 0.3 at.% Cd, 6.0 at.% In, 0.3 at.% Sb, and 2.2 at.% Bi. The addition of impurities had a large effect on eta for the In alloys, with eta reversing sign for some Sn and Pb alloy contents (chi). The T/sub c/-vs-epsilon curves also became nonlinear for some chi. The possible relationship of the In alloy results to changes in the Fermi surface due to the addition of impurities is discussed. For the Sn alloy samples, there was no change in eta with any impurity. The change in room-temperature resistivity with strain was also measured. There was only a slight decrease in the dependence of resistivity on strain for the In--Sn and In--Pb data and no effect on the In--Tl or Sn alloy data

Crystallization and memory programming characteristics of Ge-doped SbTe materials of varying Sb : Te ratio

International Nuclear Information System (INIS)

Jeong, Jeung-hyun; Lee, Hyun Seok; Lee, Suyoun; Lee, Taek Sung; Kim, Won Mok; Wu Zhe; Cheong, Byung-ki; Kim, Seul Cham; Oh, Kyu Hwan

2009-01-01

A phase change memory (PCM) utilizes resistivity changes accompanying fast transitions from an amorphous to a crystalline phase (SET) and vice versa (RESET). An investigation was made on the SET characteristics of PCM cells with Ge-doped SbTe (Ge-ST) materials of two different Sb : Te ratios (4.53 and 2.08). For the material of higher Sb : Te (4.53), a SET operation was completed within several tens of nanoseconds via nucleation-free crystallization whereas the material of lower Sb : Te (2.08) rendered a slower SET operation requiring several hundred nanoseconds for a nucleation-mediated crystallization. From measurements of nucleation and growth kinetics via laser-induced crystallization, the observed SET characteristics of the former case were found to derive from a growth time about 10 3 times shorter than the nucleation time and those of the latter from a much shorter nucleation time as well as a longer growth time than in the former case. The measured nucleation kinetics of the lower Sb : Te (2.08) material is unexpected from the existing data, which has led us to advance an interesting finding that there occurs a trend-reversing change in the nucleation kinetics of the Ge-ST materials around the eutectic composition (Sb : Te ∼2.6); nucleation is accelerated with the increase in the Sb : Te ratio above Sb : Te of 2.6, but with a decrease in the Sb : Te ratio below it.

Synthesis and characterization of PVP/ Sb2S3 composite films

International Nuclear Information System (INIS)

Salema, A.M.; Marzouka, S.; Khafagib, M.G.

2005-01-01

Polyvinyl pyrrolidone has been successfully used as a matrix to embedded Sb 2 S 3 nanoparticles. PVP thin films containing 5-25 wt % Sb 2 S 3 were deposited onto glass substrates by dip coating. X-ray diffraction spectra revealed that Sb 2 S 3 crystals depressed as nanometer-sized in the PVP matrix and the result was confirmed via scanning electron microscopy. The transmission and reflection spectra of the prepared samples were recorded in the wavelength optical range 250-2500 nm. The transmission spectra of the films show that transmission valley shifts toward higher wavelengths with increasing Sb 2 S 3 wt %. The optical constants of the deposited films, such as refractive index, extinction coefficient were obtained using the transmission and reflection data. The spectral behaviour of the loss factor, as well as the real and imaginary parts of the optical conductivity were also presented

Sb,123121 nuclear quadrupole resonance as a microscopic probe in the Te-doped correlated semimetal FeSb2: Emergence of electronic Griffith phase, magnetism, and metallic behavior

Science.gov (United States)

Gippius, A. A.; Zhurenko, S. V.; Hu, R.; Petrovic, C.; Baenitz, M.

2018-02-01

Sb,123121 nuclear quadrupole resonance (NQR) was applied to Fe(Sb1-xTex)2 in the low doping regime (x =0 , 0.01, and 0.05) as a microscopic zero field probe to study the evolution of 3 d magnetism and the emergence of metallic behavior. Whereas the NQR spectra itself reflects the degree of local disorder via the width of the individual NQR lines, the spin lattice relaxation rate (SLRR) 1 /T1(T ) probes the fluctuations at the Sb site. The fluctuations originate either from conduction electrons or from magnetic moments. In contrast to the semimetal FeSb2 with a clear signature of the charge and spin gap formation in 1 /T1(T ) T [˜exp/(Δ kBT ) ] , the 1% Te-doped system exhibits almost metallic conductivity and the SLRR nicely confirms that the gap is almost filled. A weak divergence of the SLRR coefficient 1 /T1(T ) T ˜T-n˜T-0.2 points towards the presence of electronic correlations towards low temperatures. This is supported by the electronic specific heat coefficient γ =(Cel/T ) showing a power-law divergence γ (T ) ˜T-m˜(1/T1T ) 1 /2˜T-n /2˜Cel/T which is expected in the renormalized Landau Fermi liquid theory for correlated electrons. In contrast to that the 5% Te-doped sample exhibits a much larger divergence in the SLRR coefficient showing 1 /T1(T ) T ˜T-0.72 . According to the specific heat divergence a power law with n =2 m =0.56 is expected for the SLRR. This dissimilarity originates from admixed critical magnetic fluctuations in the vicinity of antiferromagnetic long range order with 1 /T1(T ) T ˜T-3 /4 behavior. Furthermore Te-doped FeSb2 as a disordered paramagnetic metal might be a platform for the electronic Griffith phase scenario. NQR evidences a substantial asymmetric broadening of the Sb,123121 NQR spectrum for the 5% sample. This has a predominant electronic origin in agreement with the electronic Griffith phase and stems probably from an enhanced Sb-Te bond polarization and electronic density shift towards the Te atom inside Sb

Two cases of hyperparathyroidism revealed by /sup 201/Tl-chloride

Energy Technology Data Exchange (ETDEWEB)

Otsuka, Kokichi; Asano, Haruko; Moriyama, Shigeharu (Okayama Red Cross Hospital (Japan))

1983-08-01

/sup 201/Tl scintigraphy at 15 min and 120 min after intravenous injection of /sup 201/TlCl revealed a parathyroidal adenoma (1.7g) in a 49-year-old female patient with hyperthyroidism complicated by renal calculi and that (1.8g) in a 58-year-old female patient without symptoms. /sup 75/Se could be substituted by /sup 201/Tl which was useful for localizing parathyroidal adenoma in hyperparathyroidism. /sup 201/Tl scintigraphy revealed the adenoma which was not palpable. The smallest adenoma detected by it was 0.9g.

Methods, qualitative and quantitative evaluations of 201Tl myocardial scintiscans

International Nuclear Information System (INIS)

Buell, U.; Kleinhans, E.; Klepzig, M.; Seiderer, M.; Strauer, B.E.

1981-01-01

Exercise 201 Tl myocardial scintiscanning is a technique used to supplement exercise electrocardiography. The procedure employed should be identical to the standard procedure of electrocardiography. If the coronary disease has already been established by coronary angiography and kineventriculography, 201 Tl examinations should be carried out before surgery in order to determine the ''regional functional reserve''. Visual evaluations of the 201 Tl scintiscans should be supplemented by quantification methods. Quantification is also required between 201 Tl examination and surgery and to assure constant diagnostic accuracy in case of examination by different examiners. (orig./MG) [de

Single crystal growth and electrical and magnetic measurements on CeFe4Sb12

International Nuclear Information System (INIS)

Mori, I.; Sugawara, H.; Magishi, K.; Saito, T.; Koyama, K.; Kikuchi, D.; Tanaka, K.; Sato, H.

2007-01-01

We have succeeded in growing single crystals of CeFe 4 Sb 12 by a Sb-self-flux method and measured the electrical resistivity and magnetization. The residual resistivity is about two times smaller than that of polycrystalline ones, suggesting that the sample quality is highly improved. The magnetization measurements at low temperature revealed that the sample contains almost no magnetic impurities which are always observed in polycrystalline samples. The weak temperature dependence and a broad maximum around 115K in magnetic susceptibility, which is a typical feature of valence fluctuation compounds, have been observed

A Call for Expanding Inclusive Student Engagement in SoTL

Directory of Open Access Journals (Sweden)

Peter Felten

2013-09-01

of student-faculty partnerships focused on inquiry into teaching and learning. However, some students tend to be privileged in SoTL initiatives while others are discouraged, implicitly or explicitly, from engaging in this work. In this paper, we consider why certain students tend to be excluded from SoTL, summarize the possible developmental gains made by students and faculty when diverse student voices are included, and highlight strategies for generating a more inclusive SoTL. We call for expanding student engagement in SoTL by encouraging a diversity of student voices to engage in co-inquiry with faculty. Inclusive engagement has tremendous potential to enhance student and faculty learning, to deepen SoTL initiatives, and to help redress the exclusionary practices that too often occur in higher education.

Development of tailor-made silica fibres for TL dosimetry

International Nuclear Information System (INIS)

Bradley, D.A.; Abdul Sani, Siti F.; Alalawi, Amani I.; Jafari, S.M.; Noor, Noramaliza M.; Hairul Azhar, A.R.; Mahdiraji, Ghafour Amouzad; Tamchek, Nizam; Ghosh, S.; Paul, M.C.; Alzimami, Khalid S.; Nisbet, A.; Maah, M.J.

2014-01-01

The Ge dopant in commercially available silica optical fibres gives rise to appreciable thermoluminscence (TL), weight-for-weight offering sensitivity to MV X-rays several times that of the LiF dosimeter TLD100. The response of these fibres to UV radiation, X-rays, electrons, protons, neutrons and alpha particles, with doses from a fraction of 1 Gy up to 10 kGy, have stimulated further investigation of the magnitude of the TL signal for intrinsic and doped SiO 2 fibres. We represent a consortium effort between Malaysian partners and the University of Surrey, aimed at production of silica fibres with specific TL dosimetry applications, utilizing modified chemical vapour deposition (MCVD) doped silica–glass production and fibre-pulling facilities. The work is informed by defect and dopant concentration and various production dependences including pulling parameters such as temperature, speed and tension; the fibres also provide for spatial resolutions down to <10 µm, confronting many limitations faced in use of conventional (TL) dosimetry. Early results are shown for high spatial resolution (∼0.1 mm) single-core Ge-doped TL sensors, suited to radiotherapy applications. Preliminary results are also shown for undoped flat optical fibres of mm dimensions and Ge-B doped flat optical fibres of sub-mm dimensions, with potential for measurement of doses in medical diagnostic applications. - Highlights: • Optical fibres tailor-made for TL dosimetry. • Sensitive to diagnostic as well as therapy doses in medicine. • Preform and fibre pulling facilities. • Relative TL and EPR measurements

X-ray photoemission studies of Zn doped Cu1-xTl xBa2Ca2Cu 3-yZn yO10-δ (y = 0, 2.65) superconductors

International Nuclear Information System (INIS)

Khan, Nawazish A.; Mumtaz, M.; Ahadian, M.M.; Iraji-zad, Azam

2007-01-01

The X-ray photoemission (XPS) measurements of Cu 1-x Tl x Ba 2 Ca 2 Cu 3-y Zn y O 10-δ (y = 0, 2.65) superconductors have been performed and compared. These studies revealed that the charge state of thallium in the Cu 0.5 Tl 0.5 Ba 2 O 4-δ charge reservoir layer in Zn doped samples is Tl 1+ , while it is a mix of Tl 1+ and Tl 2+ in Zn free samples. The binding energy of Ba atoms in the Zn doped samples is shifted to higher energy, which when considered along with the presence of Tl 1+ suggested that it more efficiently directed the carriers to ZnO 2 and CuO 2 planes. The evidence of improved inter-plane coupling witnessed in X-ray diffraction is also confirmed by XPS measurements of Ca atoms in the Zn doped samples. The shift of the valance band spectrum in these Zn doped samples to higher energies suggested that the electrons at the top edge of the valance band were tied to a higher binding energy (relative to samples without Zn doping), which most likely resulted in a much lower energy state of the system in the superconducting state. The stronger superconducting state arising out of these effects is witnessed in the form of increased T c (R 0), J c and the extent of diamagnetism in the final compound

Conceptualizing and Communicating SoTL: A Framework for the Field

Directory of Open Access Journals (Sweden)

Janice Miller-Young

2015-09-01

Full Text Available The emerging field of SoTL is an inherently interdisciplinary endeavor which requires embracing a diverse range of research methods and disciplinary differences in world views. This diversity has caused a lack of coherence in its conceptualization and communication, which can be confusing for new scholars. Ongoing debates in the community concern the use of theory and methodology, as well as definitional questions of what constitutes SoTL and the nature of its purpose. This article offers a framework for conceptualizing the field which attempts to broadly delineate the available learning theories underlying and methodologies appropriate to studying teaching and learning, while intending to be hospitable to a broad range of diverse disciplines. Further, the framework illustrates the tacit links between learning theories and methodologies, serving as a guide to potential approaches to SoTL work. The framework is illustrated with example SoTL studies. It is hoped that the framework will help ground future SoTL investigations in appropriate theories and methodologies, and build interdisciplinary communication and understanding in the “trading zone” that is SoTL.

Experimental studies on radiation damages of CsI(Tl) crystals

International Nuclear Information System (INIS)

He Jingtang; Mao Yufang; Dong Xiaoli; Chen Duanbao; Li Zuhao

1997-01-01

The results of experimental studies on radiation damage of CsI(Tl) crystal were reported. There are radiation damage effects on CsI(Tl) crystal. Experimental studies on recovery of damaged CsI(Tl) crystals were made. It seems that after heating at 200 degree C for 4 hours, the damaged crystals could be recovered completely

AgSbSe2 and AgSb(S,Se)2 thin films for photovoltaic applications

International Nuclear Information System (INIS)

Garza, J.G.; Shaji, S.; Rodriguez, A.C.; Das Roy, T.K.; Krishnan, B.

2011-01-01

Silver antimony selenide (AgSbSe 2 ) thin films were prepared by heating sequentially deposited multilayers of antimony sulphide (Sb 2 S 3 ), silver selenide (Ag 2 Se), selenium (Se) and silver (Ag). Sb 2 S 3 thin film was prepared from a chemical bath containing SbCl 3 and Na 2 S 2 O 3 , Ag 2 Se from a solution containing AgNO 3 and Na 2 SeSO 3 and Se thin films from an acidified solution of Na 2 SeSO 3 , at room temperature on glass substrates. Ag thin film was deposited by thermal evaporation. The annealing temperature was 350 deg. C in vacuum (10 -3 Torr) for 1 h. X-ray diffraction analysis showed that the thin films formed were polycrystalline AgSbSe 2 or AgSb(S,Se) 2 depending on selenium content in the precursor films. Morphology and elemental analysis of these films were done using scanning electron microscopy and energy dispersive X-ray spectroscopy. Optical band gap was evaluated from the UV-visible absorption spectra of these films. Electrical characterizations were done using Hall effect and photocurrent measurements. A photovoltaic structure: glass/ITO/CdS/AgSbSe 2 /Al was formed, in which CdS was deposited by chemical bath deposition. J-V characteristics of this structure showed V oc = 435 mV and J sc = 0.08 mA/cm 2 under illumination using a tungsten halogen lamp. Preparation of a photovoltaic structure using AgSbSe 2 as an absorber material by a non-toxic selenization process is achieved.

Atmospheric Sb in the Arctic during the past 16,000 years: Responses to climate change and human impacts

Science.gov (United States)

Krachler, Michael; Zheng, Jiancheng; Fisher, David; Shotyk, William

2008-03-01

Applying strict clean room procedures and sector field inductively coupled plasma mass spectrometry (ICP-MS) methods, concentrations of Sb and Sc were determined in 57 sections of a 170.6-m-long ice core drilled on Devon Island, Arctic Canada, in 1999, providing a record of atmospheric Sb extending back 15,800 years. Natural background concentrations of Sb and Sc established during the period between 1300 years BP and 10,590 years BP averaged 0.08 ± 0.03 pg/g (N = 18) and 0.44 ± 0.20 pg/g (N = 17), respectively. Scandium, a conservative reference element, was used as a surrogate for mineral dust inputs. The Sb/Sc ratio of 0.13 ± 0.07 in these ancient ice samples is comparable to the corresponding ratio of 0.09 ± 0.03 in peat samples from Switzerland from circa 6000 to 9000 years BP, indicating that this natural background ratio might have a much broader validity. The natural background flux of Sb (0.7 ± 0.5 ng/m2/a) in the Arctic was approximately 500 times lower than that established in central Europe using peat cores. For comparison with background values, modern Sb fluxes calculated using 45 samples from a 5-m snow pit dug on Devon Island in 2004, reflecting 10 years of snow accumulation, yielded an average deposition rate of 340 ± 270 ng/m2/a (range: 20-1240 ng/m2/a) with pronounced accumulation of Sb during winter periods when air masses reaching the Arctic predominantly come from Eurasia. These data reveal that approximately 99.8% of the Sb deposited in the Arctic today originates from anthropogenic activities. Modern Sb enrichment factors averaged 25 (range: 8-121). The ice core provides evidence of Sb contamination dating from Phoenician/Greek, Roman, and medieval lead mining and smelting in Europe. Moreover, the ice core data indicate that anthropogenic sources of Sb have continuously dominated the atmospheric inputs to the Arctic for at least 700 years.

Characteristics of phase transition and separation in a In-Ge-Sb-Te system

Energy Technology Data Exchange (ETDEWEB)

Park, Sung Jin [Institute of Physics and Applied Physics, Yonsei University, Seoul 120-749 (Korea, Republic of); Jang, Moon Hyung [Department of Materials Science and Engineering, University of Pennsylvania, Philadelphia, PA 19104 (United States); Park, Seung-Jong [Institute of Physics and Applied Physics, Yonsei University, Seoul 120-749 (Korea, Republic of); Cho, Mann-Ho, E-mail: mh.cho@yonsei.ac.kr [Institute of Physics and Applied Physics, Yonsei University, Seoul 120-749 (Korea, Republic of); Ko, Dae-Hong [Department of Material Science and Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of)

2012-10-01

Highlights: Black-Right-Pointing-Pointer InGeSbTe films were fabricated via co-deposition stoichiometric GST and IST targets. Black-Right-Pointing-Pointer As the amount of IST was increased in InGeSbTe, the value for V{sub th} and the phase transition temperature were increased. Black-Right-Pointing-Pointer The phase separation in InGeSbTe is caused by differences in the enthalpy change for formation and different atomic concentrations. - Abstract: In-doped GeSbTe films were deposited by ion beam sputtering deposition (IBSD) using Ge{sub 2}Sb{sub 2}Te{sub 5} (GST) and In{sub 3}Sb{sub 1}Te{sub 2} (IST) as targets. The phase change characteristics of the resulting films were then investigated by electrical measurements, including static testing, in situ 4-point R{sub s} measurements, X-ray diffraction (XRD), transmission electron microscopy (TEM) and Raman spectroscopy. The threshold voltage of the films increased, with increasing levels of IST. This phenomenon is consistent with the increased crystallization temperature in X-ray data and in situ 4-point R{sub s} data. In addition, in In{sub 28}Ge{sub 12}Sb{sub 26}Te{sub 34}, multiple V{sub th} values with a stepwise change are observed. The minimum time for the crystallization of InGeSbTe films was shorter than that for GST. X-ray data and Raman data for the crystalline structure show that phase separation to In{sub 2}Te{sub 3} occurred in all of the InGeSbTe samples after annealing at 350 Degree-Sign C. Moreover, in the case of InGeSbTe films with high concentrations of In (28 at.%), Sb phase separation was also observed. The observed phases indicate that the origin of the phase separation of InGeSbTe films is from the enthalpy change of formation and differences in Ge-Te, In-Te, Sb-Te, In-Sb and In-In bond energies.

Prediction of Phase Separation of Immiscible Ga-Tl Alloys

Science.gov (United States)

Kim, Yunkyum; Kim, Han Gyeol; Kang, Youn-Bae; Kaptay, George; Lee, Joonho

2017-06-01

Phase separation temperature of Ga-Tl liquid alloys was investigated using the constrained drop method. With this method, density and surface tension were investigated together. Despite strong repulsive interactions, molar volume showed ideal mixing behavior, whereas surface tension of the alloy was close to that of pure Tl due to preferential adsorption of Tl. Phase separation temperatures and surface tension values obtained with this method were close to the theoretically calculated values using three different thermodynamic models.

Reactive ion etching of GaSb, (Al,Ga)Sb, and InAs for novel device applications

International Nuclear Information System (INIS)

LaTulipe, D.C.; Frank, D.J.; Munekata, H.

1991-01-01

Although a variety of novel device proposals for GaSb/(Al,Ga)Sb/InAs heterostructures have been made, relatively little is known about processing these materials. The authors of this paper have studied the reactive ion etching characteristics of GaSb, (Al,Ga)Sb, and InAs in both methane/hydrogen and chlorine gas chemistries. At conditions similar to those reported elsewhere for RIE of InP and GaAs in CH 4 /H 2 , the etch rate of (Al,Ga)Sb was found to be near zero, while GaSb and InAs etched at 200 Angstrom/minute. Under conditions where the etch mechanism is primarily physical sputtering, the three compounds etch at similar rates. Etching in Cl 2 was found to yield anistropic profiles, with the etch rate of (Al,Ga)Sb increasing with Al mole fraction, while InAs remains unetched. Damage to the InAs stop layer was investigated by sheet resistance and mobility measurements. These etching techniques were used to fabricate a novel InAs- channel FET composed of these materials. Several scanning electron micrographs of etching results are shown along with preliminary electrical characteristics

Stability of Tl-Ba-Ca-Cu-O superconducting thin films

International Nuclear Information System (INIS)

Siegal, M. P.; Overmyer, D. L.; Venturini, E. L.; Padilla, R. R.; Provencio, P. N.

1999-01-01

We report the stability of TlBa 2 CaCu 2 O 7 and Tl 2 Ba 2 CaCu 2 O 8 on LaAlO 3 (100) epitaxial thin films, under a variety of conditions. All films are stable in acetone and methanol and with repeated thermal cycling to cryogenic temperatures. Moisture, especially vapor, degrades film quality rapidly. These materials are stable to high temperatures in either N 2 or O 2 ambients. While total degradation, resulting from Tl depletion, occurs at the same temperatures for both phases, 600 degree sign C in N 2 and 700 degree sign C in O 2 , the onset of degradation occurs at somewhat lower temperatures for TlBa 2 CaCu 2 O 7 than for Tl 2 Ba 2 CaCu 2 O 8 . (c) 1999 Materials Research Society

Evaporation of tetramers in Sb4n clusters and conditions for the formation of Sb2n+1 clusters

International Nuclear Information System (INIS)

Rayane, D.; Tribollet, B.; Broyer, M.; Melinon, P.; Cabaud, B.; Hoareau, A.

1989-01-01

Antimony clusters are produced by the inert gas condensation technique. They are found to be built from Sb 4 units. The fragmentation by evaporation of Sb 4 units is studied as a function of the excess energy in the cluster. By this way the binding energy of the Sb 4 units in the cluster is found to be about 1.5 eV, well below the binding energy of a Sb atom in the bulk and in Sb 4 (≅3 eV). The evolution of ionization potentials of Sb 4n clusters confirms that their structure is probably non metallic. Finally the possible metastable character of this Sb 4n structure is discussed. (orig.)

Optimization of growth parameters for MOVPE-grown GaSb and Ga1−xInxSb

International Nuclear Information System (INIS)

Miya, S.S.; Wagener, V.; Botha, J.R.

2012-01-01

The triethylgallium/trimethylantimony (TEGa/TMSb) precursor combination was used for the metal-organic vapour phase epitaxial growth of GaSb at a growth temperature of 520 °C at atmospheric pressure. Trimethylindium was added in the case of Ga 1−x In x Sb growth. The effects of group V flux to group III flux ratio (V/III ratio) on the crystallinity and optical properties of GaSb layers are reported. It has been observed from the crystalline quality and optical properties that nominal V/III ratios of values greater than unity are required for GaSb epitaxial layers grown at this temperature. It has also been shown that Ga 1−x In x Sb can be grown using TEGa as a source of gallium species at atmospheric pressure. The relationship between Ga 1−x In x Sb vapour composition and solid composition has been studied at a V/III ratio of 0.78.

TL1A regulates TCRγδ+ intraepithelial lymphocytes and gut microbial composition

DEFF Research Database (Denmark)

Tougaard, Peter; Skov, S.; Pedersen, A. E.

2015-01-01

TL1A is a proinflammatory cytokine, which is prevalent in the gut. High TL1A concentrations are present in patients with inflammatory bowel disease (IBD) and in IBD mouse models. However, the role of TL1A during steady‐state conditions is relatively unknown. Here, we used TL1A knockout (KO) mice ...

Comparative analysis of oxide phase formation and its effects on electrical properties of SiO{sub 2}/InSb metal-oxide-semiconductor structures

Energy Technology Data Exchange (ETDEWEB)

Lee, Jaeyel [Department of Materials Science and Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); Park, Sehun [Department of Materials Science and Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); WCU Hybrid Materials Program, Department of Materials Science and Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); Kim, Jungsub; Yang, Changjae; Kim, Sujin; Seok, Chulkyun [Department of Materials Science and Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); Park, Jinsub [Department of Electronic Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Yoon, Euijoon, E-mail: eyoon@snu.ac.kr [Department of Materials Science and Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); WCU Hybrid Materials Program, Department of Materials Science and Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); Department of Nano Science and Technology, Graduate School of Convergence Science and Technology, Seoul National University, Suwon 443-270 (Korea, Republic of); Energy Semiconductor Research Center, Advanced Institutes of Convergence Technology, Seoul National University, Suwon 443-270 (Korea, Republic of)

2012-06-01

We report on the changes in the interfacial phases between SiO{sub 2} and InSb caused by various deposition temperatures and heat treatments. X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy were used to evaluate the relative amount of each phase present at the interface. The effect of interfacial phases on the electrical properties of SiO{sub 2}/InSb metal-oxide-semiconductor (MOS) structures was investigated by capacitance-voltage (C-V) measurements. The amount of both In and Sb oxides increased with the deposition temperature. The amount of interfacial In oxide was larger for all samples, regardless of the deposition and annealing temperatures and times. In particular, the annealed samples contained less than half the amount of Sb oxide compared with the as-deposited samples, indicating a strong interfacial reaction between Sb oxide and the InSb substrate during annealing. The interface trap density sharply increased for deposition temperatures above 240 Degree-Sign C. The C-V measurements and Raman spectroscopy indicated that elemental Sb accumulation due to the interfacial reaction of Sb oxide with InSb substrate was responsible for the increased interfacial trap densities in these SiO{sub 2}/InSb MOS structures. - Highlights: Black-Right-Pointing-Pointer We report the quantitative analysis of interfacial oxides at the SiO{sub 2}/InSb interface. Black-Right-Pointing-Pointer Interfacial oxides were measured quantitatively by X-ray Photoelectron Spectroscopy. Black-Right-Pointing-Pointer As-grown and annealed samples showed different compositions of oxide phases. Black-Right-Pointing-Pointer Considerable reduction of antimony oxide phases was observed during annealing. Black-Right-Pointing-Pointer Interface trap densities at the SiO{sub 2}/InSb interface were calculated.

Photon and neutron energy response of Thermoluminescent (TL) dosimeters

International Nuclear Information System (INIS)

Thilagam, L.; Priya, M.R.; Mohapatra, D.K.

2018-01-01

Theoretical Monte Carlo (MC) simulations are carried out to investigate the relative thermoluminesence (TL) response of the most commonly used TLD materials to a wide range of photon energy. The effect of polytetrafluoroethylene (PTFE) on TL response of CaSO 4 :Dy is also studied. Additionally, the neutron response of LiF:Mg,Ti TL materials with different concentrations of 6 Li is estimated in terms of the number of 6 Li(n, t) 4 He capture reactions for a wider neutron energy

Neutron capture at the s-process branching points $^{171}$Tm and $^{204}$Tl

CERN Multimedia

Branching points in the s-process are very special isotopes for which there is a competition between the neutron capture and the subsequent b-decay chain producing the heavy elements beyond Fe. Typically, the knowledge on the associated capture cross sections is very poor due to the difficulty in obtaining enough material of these radioactive isotopes and to measure the cross section of a sample with an intrinsic activity; indeed only 2 out o the 21 ${s}$-process branching points have ever been measured by using the time-of-flight method. In this experiment we aim at measuring for the first time the capture cross sections of $^{171}$Tm and $^{204}$Tl, both of crucial importance for understanding the nucleosynthesis of heavy elements in AGB stars. The combination of both (n,$\\gamma$) measurements on $^{171}$Tm and $^{204}$Tl will allow one to accurately constrain neutron density and the strength of the 13C(α,n) source in low mass AGB stars. Additionally, the cross section of $^{204}$Tl is also of cosmo-chrono...

Magnetism and superconductivity of some Tl-Cu oxides

Science.gov (United States)

Datta, Timir

1991-01-01

Many copper oxide based Thallium compounds are now known. In comparison to the Bi-compounds, the Tl-system shows a richer diversity; i.e., High Temperature Superconductors (HTSC) can be obtained with either one or two Tl-0 layers (m = 1,2); also, the triple-digit phases are easier to synthesize. The value of d, oxygen stoichiometry, is critical to achieving superconductivity. The Tl system is robust to oxygen loss; Tl may be lost or incorporated by diffusion. A diffusion coefficient equal to 10 ms at 900 C was determined. Both ortho-rhombic and tetragonal structures are found, but HTSC behavior is indifferent to the crystal symmetry. This system has the highest T(sub c) confirmed. T(sub c) generally increases with p, the number of CuO layers, but tends to saturate at p = 3. Zero resistance was observed at temperatures as great as 125 K. Most of these HTSC's are hole type, but the Ce-doped specimens may be electronic. The magnetic aspects were studied; because in addition to defining the perfectly diamagnetic ground state as in conventional superconductors, magnetism of the copper oxides show a surprising variety. This is true of both the normal and the superconducting states. Also, due to the large phonon contribution to the specific heat at the high T(sub c) jump, electronic density of states, D(Ef), and coherence length are uncertain, and thus, are estimated from the magnetic results. Results from the Tl-system CuO, LaBaCuO,120 and the Bi-CuO compounds are discussed. The emphasis is on the role of magnetism in the Tl-CuO HTSC, but technological aspects are also pointed out.

In situ study of the formation kinetics of InSb quantum dots grown in an InAs(Sb) matrix

International Nuclear Information System (INIS)

Semenov, A. N.; Lyublinskaya, O. G.; Solov’ev, V. A.; Mel’tser, B. Ya.; Ivanov, S. V.

2008-01-01

Formation of InSb quantum dots grown in an InAs matrix by molecular-beam epitaxy that does not involve forced deposition of InSb is studied. Detection of intensity oscillations in the reflection of high-energy electron diffraction patterns was used to study in situ the kinetics of the formation of InSb quantum dots and an InAsSb wetting layer. The effects of the substrate temperature, the shutter operation sequence, and the introduction of growth interruptions on the properties of the array of InSb quantum dots are examined. Introduction of a growth interruption immediately after completing the exposure of the InAs surface to the antimony flux leads to a reduction in the nominal thickness of InSb and to an enhancement in the uniformity of the quantum-dot array. It is shown that, in the case of deposition of submonolayer-thickness InSb/InAs quantum dots, the segregation layer of InAsSb plays the role of the wetting layer. The Sb segregation length and segregation ratio, as well as their temperature dependences, are determined.

Microstructure analyses and thermoelectric properties of Ag1−xPb18Sb1+yTe20

International Nuclear Information System (INIS)

Perlt, S.; Höche, Th.; Dadda, J.; Müller, E.; Bauer Pereira, P.; Hermann, R.; Sarahan, M.; Pippel, E.; Brydson, R.

2012-01-01

This study reports microstructural investigations of long-term annealed Ag 1−x Pb m Sb 1+y Te 2+m (m=18, x=y=0, hereinafter referred to as AgPb 18 SbTe 20 ) (Lead–Antimony–Silver–Tellurium, LAST-18) as well as of Ag 1−x Pb 18 Sb 1+y Te 20 , i.e. Ag-deficient and Sb-excess LAST-18 (x≠0,y≠0), respectively. Two different length scales are explored. The micrometer scale was evaluated by SEM to analyze the volume fraction and the number of secondary phases as well as the impact of processing parameters on the homogeneity of bulk samples. For AgPb 18 SbTe 20 , site-specific FIB liftout of TEM lamellae from thermoelectrically characterized samples was accomplished to investigate the structure on the nanometer scale. High-resolution TEM and energy-filtered TEM were performed to reveal shape and size distribution of nanoprecipitates, respectively. A hypothesis concerning the structure–property relationship is set out within the frame of a gradient annealing experiment. This study is completed by results dealing with inhomogeneities on the micrometer scale of Ag 1−x Pb 18 Sb 1+y Te 20 and its electronic properties. Highlights: ► SEM and TEM microstructure investigation of long-term annealed AgPb 18 SbTe 20 . ► SEM and thermoelectric studies on Ag 1−x Pb 18 Sb 1+y Te 20 . ► Discussion concerning structure–property relationship in long-term annealed AgPb 18 SbTe 20 . ► Correlation between Ag 1−x Pb 18 Sb 1+y Te 20 microscale structure and electronic properties.

Two-equivalent electrochemical reduction of a cyano-complex [TlIII(CN)2]+ and the novel di-nuclear compound [(CN)5PtII-TlIII]0

International Nuclear Information System (INIS)

Dolidze, Tina D.; Khoshtariya, Dimitri E.; Behm, Martin; Lindbergh, Goeran; Glaser, Julius

2005-01-01

Extending our recent insights in two-electron transfer microscopic mechanisms for a Tl III /Tl I redox system [D.E. Khoshtariya, et al., Inorg. Chem. 41 (2002) 1728], the electrochemical response of glassy carbon electrode in acidified solutions of Tl III (ClO 4 ) 3 containing different concentrations of sodium cyanide has been extensively studied for the first time by use of cyclic voltammetry and the CVSIM curve simulation PC program. The complex [Tl III (CN) 2 ] + has been thoroughly identified electrochemically and shown to display a single well-defined reduction wave (which has no anodic counterpart), ascribed to the two-equivalent process yielding [Tl I (aq)] + . This behavior is similar to that of [Tl III (aq)] 3+ ion in the absence of sodium cyanide, disclosed in the previous work, and is compatible with the quasi-simultaneous yet sequential two-electron transfer pattern (with two reduction waves merged in one), implying the rate-determining first electron transfer step (resulting in the formation of a covalently interacting di-thallium complex as a metastable intermediate), and the fast second electron transfer step. Some preliminary studies of the two-equivalent reduction of directly metal-metal bonded stable compound [(CN) 5 Pt II -Tl III ] 0 has been also performed displaying two reduction waves compatible with a true sequential pattern

Left ventricular ejection fraction determined by gated Tl-201 perfusion SPECT and quantitative software

International Nuclear Information System (INIS)

Hyun, In Young; Kim, Sung Eun; Seo, Jeong Kee; Hong, Eui Soo; Kwan, Jun; Park, Keum Soo; Lee, Woo Hyung

2000-01-01

We compared estimates of ejection fraction (EF) determined by gated Tl-201 perfusion SPECT (g-Tl-SPECT) with those by gated blood pool (GBP) scan. Eighteen subjects underwent g-Tl-SPECT and GBP scan. After reconstruction of g-Tl-SPECT, we measured EF with Cedars software. The comparison of the EF with g-Tl-SPECT and GBP scan was assessed by correlation analysis and Bland Altman plot. The estimates of EF were significantly different (p<0.05) with g-Tl-SPECT (40%±14%) and GBP scan (43%±14%). There was an excellent correlation of EF between g-Tl-SPECT and GBP scan (r=3D0.94, p<0.001). The mean difference of EF between GBP scan and g-Tl-SPECT was +3.2%. Ninety-five percent limits of agreement were ±9.8%. EF between g-Tl-SPECT and GBP scan were in poor agreement. The estimates of EF by g-Tl-SPECT was well correlated with those by GBP scan. However, EF of g-Tl-SPECT doesn't agree with EF of GBP scan. EF of g-Tl-SPECT can't be used interchangeably with EF of GBP scan.=20

Phase equilibria melt-solid in the systems Pb-InSb-CaSb and Pb-InCs-GaAs

International Nuclear Information System (INIS)

Grebenyuk, A.M.; Charykov, N.A.; Puchkov, L.V.

1992-01-01

Results of experimental investigation and thermodynamic calculation of fusibility curves of Pb-InSb-GaSb and Pb-InAs-GaAs thernary systems, which haven't been investigated earlier, are presented. Fusibility curves of Pb-InSb-GaSb and Pb-InAs-GaAs systems contain two crystallization fields: solid solutions of In x Ga 1-x Sb and Pb, In x Ga 1-x As and Pb. The latter fields are retained against Pb figurative point and conform to 582 K < T < 593 K crystallization temperatures

Progress and problems with automated TL dating

International Nuclear Information System (INIS)

McKerrell, H.; Mejdahl, V.

1981-01-01

A number of basic problems connected with the measurement of beta and gamma dose-rates are discussed, and the possibility of using low-temperature peaks in quartz and feldspar for dose-rate measurements is examined. Preliminary results of TL measurements on individual grains of quartz and feldspar are presented. A TL dating method based on the difference in the archaeological dose received by potassium feldspar and quartz grains is proposed. (author)

Irradiated Foods Detection by Thermoluminescence (TL) and DEFT/APC Analysis

International Nuclear Information System (INIS)

Choi, I.D.; Kang, E.K.; Yang, J.S.

2004-01-01

Irradiated food detection methods such as Thermoluminescence (TL) and Direct Epifluorescent Filter Technique and Aerobic Plate Count (DEFT/APC) methods were evaluated. Fresh green-onion, onion, and ginger were irradiated at 0, 0.3, 0.6, and 0.9 kGy. Difference in log DEFT/APC units between irradiated and un-irradiated samples was less than 2 long units, below the average threshold value (3-4 long units) of international researches

The Tl{sub 2}S–PbS–SiS{sub 2} system and the crystal and electronic structure of quaternary chalcogenide Tl{sub 2}PbSiS{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Mozolyuk, M.Y.; Piskach, L.V. [Department of Inorganic and Physical Chemistry, Lesya Ukrainka Eastern European National University, 13 Voli Avenue, 43025, Lutsk (Ukraine); Fedorchuk, A.O. [Department of Inorganic and Organic Chemistry, Lviv National University of Veterinary Medicine and Biotechnologies, 50 Pekarska Street, 79010, Lviv (Ukraine); Olekseyuk, I.D.; Parasyuk, O.V. [Department of Inorganic and Physical Chemistry, Lesya Ukrainka Eastern European National University, 13 Voli Avenue, 43025, Lutsk (Ukraine); Khyzhun, O.Y., E-mail: khyzhun@ipms.kiev.ua [Frantsevych Institute for Problems of Materials Science, National Academy of Sciences of Ukraine, 3 Krzhyzhanivsky Street, 03142, Kyiv (Ukraine)

2017-07-01

Chalcogenides of the quasi-ternary system Tl{sub 2}S–PbS–SiS{sub 2} were synthesized in the evacuated silica ampoules by the melting and annealing technique. Phase equilibria in the system was investigated by XRD method. Isothermal section of the system was studied, and two intermediate quaternary phases were discovered to exist (Tl{sub 2}PbSiS{sub 4}, ∼Tl{sub 2}PbSi{sub 3}S{sub 8}). The quasi-binary section Tl{sub 2}SiS{sub 3}–PbS was investigated by DTA. Its phase diagram was constructed, and it was established that the equimolar compound melts incongruently at 818 K. The crystal structure of the quaternary compound Tl{sub 2}PbSiS{sub 4} was determined by X-ray powder diffraction. It crystallizes in the monoclinic space group P2{sub 1}/a with the unit-cell parameters a = 8.8141(4), b = 9.0150(5), c = 10.4383(5) Å, and β = 94.490(4)° (Tl{sub 2}PbGeS{sub 4} structure type). Reliability factors calculated in the isotropic approximation were found to be R{sub I} = 0.0564 and R{sub P} = 0.1070. The Tl{sub 2}PbSiS{sub 4} single crystal was tested with X-ray photoelectron spectroscopy. In particular, the XPS core-level and valence-band spectra were recorded for pristine and Ar{sup +}-ion bombarded surfaces of Tl{sub 2}PbSiS{sub 4}. The Tl{sub 2}PbSiS{sub 4} single crystal was found to be rather stable with respect to Ar{sup +}-ion irradiation. We have also measured the X-ray emission band depicting the energy distribution of mainly the S 3p states and compared it on a common energy scale with the XPS valence-band spectrum of the Tl{sub 2}PbSiS{sub 4} crystal. The above comparison indicates that the S 3p states contribute substantively in the upper portion of the valence band of Tl{sub 2}PbSiS{sub 4}, with their significant contributions in other portions of the valence-band region. - Highlights: • Chalcogenides of the quasi-ternary system Tl{sub 2}S–PbS–SiS{sub 2} were synthesized. • Two intermediate quaternary phases were discovered to exist (Tl

Contributions to a systematic examination of deformed transition nuclei by the study of the decay of 188Tl and 190Tl

International Nuclear Information System (INIS)

Waetzig, W.

1980-01-01

Using the reaction 197 Au( 3 He,xn) Tl the decay of the nuclides 188 Tl and 190 Tl to 188 Hg (Tsub(1/2) = 70s) respectively to 190 Hg(Tsub(1/2) = 3.0 min) was studied at the mass separator ISOCELE of the Orsay-synchrocyclotron by gamma, conversion electron, gamma-gamma coincidence, and electron-gamma coincidence spectroscopy. The level schemes of 188 Hg and 190 Hg could be remarkably extended in comparison with earlier works. By a statistical analysis of the nuclear level density the nuclear temperature was calculated as a measure for the number of excitation modes of these nuclei. (orig./HSI) [de

Preparation and oxidation resistance of single crystalline β-Zn{sub 4}Sb{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Liu, Hong-xia; Deng, Shu-ping [Education Ministry Key Laboratory of Renewable Energy Advanced Materials and Manufacturing Technology, Yunnan Normal University, Kunming 650500 (China); Li, De-cong [Photoelectric Engineering College, Yunnan Open University, Kunming 650500 (China); Shen, Lan-xian; Cheng, Feng; Wang, Jin-song [Education Ministry Key Laboratory of Renewable Energy Advanced Materials and Manufacturing Technology, Yunnan Normal University, Kunming 650500 (China); Deng, Shu-kang, E-mail: skdeng@126.com [Education Ministry Key Laboratory of Renewable Energy Advanced Materials and Manufacturing Technology, Yunnan Normal University, Kunming 650500 (China)

2016-11-01

This study prepared a Zn-rich single crystal β-Zn{sub 4}Sb{sub 3} using a Sn flux method based on the stoichiometric ratios of Zn{sub 4.4}Sb{sub 3}Sn{sub 3}. The oxidation resistance of the sample was determined by exploring the effects of heat treatment in air on electrical transport properties and thermal stability, which is of practical importance in the application of the material at high temperatures. Results showed that the prepared sample possessed high electrical transport properties, with a high power factor of 1.67×10{sup −3} W m{sup −1} K{sup −2} at 563 K. The heat treatment in air weakened the electrical conductivity of the single crystalline β-Zn{sub 4}Sb{sub 3}, whereas the Seebeck coefficients were rarely independent of the annealing condition. Eventually, the power factor obtained after the first heating at 523 K for 4 h became comparable to that of the as-prepared sample, although it decreased after the second heating at 573 K for 5 h. Nevertheless, the single crystalline β-Zn{sub 4}Sb{sub 3} still possessed a good thermal stability after the heat treatment process.

Thermoelectric properties of p-type pseudo-binary (Ag0.365Sb0.558Te) x -(Bi0.5Sb1.5Te3)1-x (x=0-1.0) alloys prepared by spark plasma sintering

International Nuclear Information System (INIS)

Cui, J.L.; Xue, H.F.; Xiu, W.J.; Jiang, L.; Ying, P.Z.

2006-01-01

In this paper, pseudo-binary (Ag 0.365 Sb 0.558 Te) x -(Bi 0.5 Sb 1.5 Te 3 ) 1- x (x=0-1.0) alloys were prepared using spark plasma sintering technique, and the composition-dependent thermoelectric properties were evaluated. Electrical conductivities range from 7.9x10 4 to 15.6x10 4 Ω -1 m -1 at temperatures of 507 and 318 K, respectively, being about 3.0 and 8.5 times those of Bi 0.5 Sb 1.5 Te 3 alloy at the corresponding temperatures. The optimal dimensionless figure of merit (ZT) of the sample with molar fraction x=0.025 reaches 1.1 at 478 K, whereas that of the ternary Bi 0.5 Sb 1.5 Te 3 alloy is 0.58 near room temperature. The results also reveal that a direct introduction of Ag 0.365 Sb 0.558 Te in the Bi-Sb-Te system is much more effective to the property improvement than naturally precipitated Ag 0.365 Sb 0.558 Te in the Ag-doped Ag-Bi-Sb-Te system. - Graphical abstract: The temperature dependence of the dimensionless thermoelectric figure of merit ZT for different (Ag 0.365 Sb 0.558 Te) x -(Bi 0.5 Sb 1.5 Te 3 ) 1- x (x=0-1.0) alloys prepared by spark plasma sintering

Performance of novel materials for radiation detection: Tl3AsSe3, TlGaSe2, and Tl4HgI6

International Nuclear Information System (INIS)

Kahler, D.; Singh, N.B.; Knuteson, D.J.; Wagner, B.; Berghmans, A.; McLaughlin, S.; King, M.; Schwartz, K.; Suhre, D.; Gotlieb, M.

2011-01-01

In this paper we report on the electrical characteristics of three novel ternary compounds, Tl 3 AsSe 3 (TAS), TlGaSe 2 (TGS), and Tl 4 HgI 6 (THI), pertaining to their use as radiation detectors. The details for growth and material characterization are not presented. A semiconductor based gamma ray detector requires a material with high Z, high density, high resistivity, appropriate bandgap (1.5-2 eV), low energy/electron-hole pair, and a high μτ product. CZT is currently the best semiconductor material for room temperature gamma ray spectroscopy; however, it is extremely difficult to produce large volumes of detector grade material, making it expensive and in limited supply. DNDO/DHS began searching for other materials that might perform as well as CZT but be easier to grow and in the end lower the cost. For this purpose, we investigated the above three materials as possible replacements for CZT as gamma ray detectors. The bulk resistivity, I-V curves, X-ray response, and gamma ray response measurements for doped and undoped crystals are presented and discussed. TAS shows good X-ray and gamma ray response, but has poor resistivity, which results in large dark current and poor spectral response. TGS has good resistivity, but shows poor X-ray and gamma ray response. THI has excellent resistivity, shows some X-ray and gamma ray response, and has great potential as a gamma ray detector.

Crystal and magnetic study of the disordered perovskites Ca(Mn0.5Sb0.5)O3 and Ca(Fe0.5Sb0.5)O3

International Nuclear Information System (INIS)

Retuerto, M.; Martinez-Lope, M.J.; Garcia-Hernandez, M.; Munoz, A.; Fernandez-Diaz, M.T.; Alonso, J.A.

2010-01-01

We have investigated the double perovskites Ca 2 MSbO 6 (M = Mn, Fe) that have been prepared by solid-state reaction (M = Fe) and wet chemistry procedures (M = Mn). The crystal and magnetic structures have been studied from X-ray (XRD) and neutron powder diffraction (NPD) data. Rietveld refinements show that the crystal structures are orthorhombic (space group Pbnm) with complete disorder of M and Sb cations, so the formula should be rewritten as Ca(M 0.5 Sb 0.5 )O 3 . Due to this disorder no evidences of Jahn-Teller distortion can be observed in the MnO 6 octahedra of Ca(Mn 0.5 Sb 0.5 )O 3 , in contrast with the ordered double perovskite Sr 2 MnSbO 6 . Ca(Fe 0.5 Sb 0.5 )O 3 behaves as an antiferromagnet with an ordered magnetic moment for Fe 3+ of 1.53(4)μ B and a propagation vector k = 0, as investigated by low-temperature NPD. The antiferromagnetic ordering is a result of the high degree of Fe/Sb anti-site disorder of the sample, which originates the spontaneous formation of Fe-rich islands, characterized by the presence of strong Fe-O-Fe antiferromagnetic couplings with enough long-range coherence to produce a magnetic contribution perceptible by NPD. By contrast, the magnetic structure of Ca(Mn 0.5 Sb 0.5 )O 3 cannot be observed by low-temperature NPD because the magnitude of the ordered magnetic moments is below the detection threshold for neutrons.

Influence of temperature in TL signal induced by gamma radiation in zircon prepared by sol gel via; Influencia de la temperatura en la senal TL inducida por la radiacion gamma en zirconia preparada via solgel

Energy Technology Data Exchange (ETDEWEB)

Salas, P.; Castano, V.M. [Instituto de Fisica, UNAM, Laboratorio Juriquilla, A.P. 1-1010, 76001 Queretaro (Mexico); Mendoza A, D.; Gonzalez M, P.R. [ININ, Mexico, D.F. (Mexico); Rosa C, E. de la [Centro de Investigaciones en Optical, Leon, Gto. (Mexico)

2000-07-01

In this work, it was realized a study of the temperature effects in thermoluminescent signal (Tl) induced by gamma radiation in zircon, which was prepared by the sol gel method. According to the obtained results, the zircon thermically treated at 500 C or over is sensitive to radiation. This sensitivity is increased when the temperature in study is augmented, moreover, the Tl spectra form also is modified with the temperature increment. The samples thermically treated at 750 C or over present a linear response in the dose interval 27 to 165 Gy; therefore, such materials result promissories for dosimetric purposes. (Author)

Leg 201Tl-SPECT in chronic exertional compartment syndrome

International Nuclear Information System (INIS)

Elkadri, N.; Slim, I.; Blondet, C.; Choquet, Ph.; Constantinesco, A.; Lecocq, J.

2004-01-01

Leg 201 Tl-SPECT in chronic exertional compartment syndrome Background: The chronic exertional compartment syndrome is one of the most frequent origins regarding leg pain due to sport training. The diagnosis can be established by invasive compartment pressure measurement. The aim of this study is to evaluate the role that could have 201 Tl-SPECT for patients with suspicion of compartment syndrome. Patients and methods: 51 leg 201 Tl-SPECT exams were performed (exercise - and rest without reinjection) in 49 patients; 28 had compartment syndrome confirmed by pressure measurement. About 100 MBq of 201 Tl were injected during exercise, when pain appeared or at least after 25 minutes exercise. We studied mean percentages of level uptake for each compartment, referred to the maximal uptake of both legs. Results: 47 compartments were concerned by compartment syndrome and 361 compartments were not. Scintigraphic patterns in compartments are reversible ischaemia (45%), uptake stability (36%) or reverse redistribution (19%); these patterns are not linked to compartment syndrome. However, there is a significant difference of rest 201 Tl level uptake between compartments with and without compartment syndrome and a significant correlation between muscular pressure measurement and rest level uptake. Conclusion: 201 Tl-SPECT shows that only ischaemia does not explain compartment syndrome. Moreover, it allows to predict pressure variation during exercise but it does not offer any interest in order to select patients for muscular invasive pressure measurement. (author)

Study of morphological and luminescent properties (TL and OSL) of ZnO nanocrystals synthetized by coprecipitation method

Energy Technology Data Exchange (ETDEWEB)

Soares, A.F., E-mail: alvarodefarias@hotmail.com; Tatumi, S.H., E-mail: sonia.tatumi@gmail.com; Mazzo, T.M.; Rocca, R.R.; Courrol, L.C.

2017-06-15

In this work, ZnO nanocrystalline phosphorus were synthesized using the method of coprecipitation, subsequently different heat treatments at 900 and 1000 °C for 2 h and 1000 °C for 4 h were performed. Afterward, Thermoluminescence (TL) and Optically Stimulated Luminescence (OSL) emissions were verified after exposure to β-radiation. Photoluminescence results showed UV and VIS emissions. Morphological studies with X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) confirmed the crystallinity of the samples, with their well-shaped wurtzite hexagonal structures in nanoscale. ZnO calcinated at 900 °C – 2 h emitted a broad TL peak located between the 362–372 °C; for ZnO calcinated at 1000 °C – 2 h, two intense peaks were observed at 144 and 308 °C, this TL emission curve was investigated with more details using Computerized Glow Curve Deconvolution and six individual TL peaks were obtained, for sample irradiated with 40.6 Gy, corroborating with the T{sub m}-T{sub stop} results. A study of Minimum Detectable Dose (MDD) was made and a dose of (492±40) μGy was determined. CW-OSL and LM-OSL analysis were made for ZnO calcinated at 1000 °C – 2 h, allowed to verify the behaviour, and the curve existing components (fast and medium, depending on dose). As well as the calculation of the Minimum Detectable Dose for CW-OSL. - Highlights: •ZnO nanocrystals were successfully produced by the method of coprecipitation. •Grains sizes by Scherrer Equation were between 26.9–40.6 nm, corroborating with SEM. •Study of the TL emission: Computerized Glow Curve Deconvolution (CGCD) and Tm-Tstop. •TL emission of ZnO calcinated supplied the minimum detectable dose of (492±40) μGy. •Study of CW-OSL and LM-OSL with CGCD. MDD for CW-OSL evaluation of ZnO calcinated.

Effect of antimony nano-scale surface-structures on a GaSb/AlAsSb distributed Bragg reflector

International Nuclear Information System (INIS)

Husaini, S.; Shima, D.; Ahirwar, P.; Rotter, T. J.; Hains, C. P.; Dang, T.; Bedford, R. G.; Balakrishnan, G.

2013-01-01

Effects of antimony crystallization on the surface of GaSb during low temperature molecular beam epitaxy growth are investigated. The geometry of these structures is studied via transmission electron and atomic force microscopies, which show the surface metal forms triangular-shaped, elongated nano-wires with a structured orientation composed entirely of crystalline antimony. By depositing antimony on a GaSb/AlAsSb distributed Bragg reflector, the field is localized within the antimony layer. Polarization dependent transmission measurements are carried out on these nano-structures deposited on a GaSb/AlAsSb distributed Bragg reflector. It is shown that the antimony-based structures at the surface favor transmission of light polarized perpendicular to the wires.

Accidental and retrospective dosimetry using TL method

International Nuclear Information System (INIS)

Mesterházy, D.; Osvay, M.; Kovács, A.; Kelemen, A.

2012-01-01

Retrospective dosimetry is one of the most important tools of accidental dosimetry for dose estimation when dose measurement was not planned. In the affected area many objects can be applied as natural dosimeters. The paper discusses our recent investigations on various electronic components and common salt (NaCl) having useful thermoluminescence (TL) properties. Among materials investigated the electronic components of cell phones seem promising for retrospective dosimetry purposes, having high TL responses, proper glow curve peaks and the intensity of TL peaks vs. gamma dose received provided nearly linear response in the dose range of 10 mGy–1.5 Gy. - Highlights: ► Electronic components and common salt were investigated for accidental and retrospective dosimetry. ► SMD resistors seem promising for retrospective dosimetry purposes. ► Table salt can be used effectively for accidental dosimetry purposes, as well.

Stability of Tl-Ba-Ca-Cu-O superconducting thin films

Energy Technology Data Exchange (ETDEWEB)

Siegal, M. P. [Sandia National Laboratories, Albuquerque, New Mexico 87185-1421 (United States); Overmyer, D. L. [Sandia National Laboratories, Albuquerque, New Mexico 87185-1421 (United States); Venturini, E. L. [Sandia National Laboratories, Albuquerque, New Mexico 87185-1421 (United States); Padilla, R. R. [Sandia National Laboratories, Albuquerque, New Mexico 87185-1421 (United States); Provencio, P. N. [Sandia National Laboratories, Albuquerque, New Mexico 87185-1421 (United States)

1999-12-01

We report the stability of TlBa{sub 2}CaCu{sub 2}O{sub 7} and Tl{sub 2}Ba{sub 2}CaCu{sub 2}O{sub 8} on LaAlO{sub 3}(100) epitaxial thin films, under a variety of conditions. All films are stable in acetone and methanol and with repeated thermal cycling to cryogenic temperatures. Moisture, especially vapor, degrades film quality rapidly. These materials are stable to high temperatures in either N{sub 2} or O{sub 2} ambients. While total degradation, resulting from Tl depletion, occurs at the same temperatures for both phases, 600 degree sign C in N{sub 2} and 700 degree sign C in O{sub 2}, the onset of degradation occurs at somewhat lower temperatures for TlBa{sub 2}CaCu{sub 2}O{sub 7} than for Tl{sub 2}Ba{sub 2}CaCu{sub 2}O{sub 8}. (c) 1999 Materials Research Society.

High current Tl-203, Rh-103 targets preparation for cyclotron production of Tl-201 and Pd-103 radionuclides

International Nuclear Information System (INIS)

Arzumanov, A.; Berger, V.; Borissenko, A.; Gorodisskaya, N.; Ilmatov, I.; Knyazev, A.; Koptev, V.; Lyssukhin, S.; Platov, A.; Sychikov, G.; Zheltov, D.

2004-01-01

The objectives of the present work are to increase thermal stability of cyclotron targets for production of Tl-201 isotope, increase Tl-203 regeneration rate at radiochemical reprocessing of the targets and develop production technology for radiochemical sources based on Rd-103 isotope. Electrochemical coating of copper substrate with Tl increased the beam current at target irradiation from 100 μA to 125 μA. Further increase of the beam current results in sharp decrease of target stability time at irradiation to 15 min at beam current 150 μA. Thermal calculations and tests at the electron-beam stand predict satisfactory stability at such currents. The discrepancy with the irradiation results has not been explained. More accurate specification of regimes for Tl-203 electrochemical recovery from irradiated targets and better matching of the electrolyte composition made it possible to increase the recovery rate up to 99.5%. Before the present Project, the INP had no experience in production of radioactive sources based on Pd-103. Thermo-diffusion extraction of Pd-103 from irradiated rhodium foil has been chosen as a technology-defining method. The process assures good extraction rate and high purity of extracted isotope. Production of Pd-103 sources based on this technology is much simpler compared to the same based on electrochemical processes. (author)

Photo-TL in CaSO4:Dy: high exposure dosimetry

International Nuclear Information System (INIS)

Caldas, L.V.E.; Mayhugh, M.R.

1974-01-01

CaSO 4 :Dy exposed to 10 3 to 10 8 R then annealed in the range 280 to 400 0 C displays little TL in the major dosimetry peak near 200 0 C. Subsequent illumination with 250 nm light reinduces the 200 0 C TL. This radiation-enabled photo-TL is roughly proportional to the square root of the enabling exposure at least to 10 8 R. (auth)

Tl response of KMgF{sub 3}: Lu + PTFE at ultraviolet radiation; Respuesta Tl de KMgF{sub 3}: Lu + PTFE a radiacion ultravioleta

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, P R [Instituto Nacional de Investigaciones Nucleares, A.P. 18 -1027, 11801 Mexico D.F. (Mexico); Alarcon, N G [Facultad de Quimica, Universidad Autonoma del Estado de Mexico. Paseo Tollocan, Esq. con Jesus Carranza, 50180 Toluca, Estado de Mexico (Mexico); Furetta, C; Azorin, J [Universidad Autonoma Metropolitana- Iztapalapa, San Rafael Atlixco 186, 09340 Mexico. D.F. (Mexico)

2003-07-01

Ionizing radiation has different types of interaction with a crystalline solid. However, only few effects are interesting to optimize some thermoluminescent (Tl) properties of certain Tl materials. This paper presents results obtained by irradiating KMgF{sub 3}: Lu + Ptfe Tl dosimeters with ultraviolet (UV) radiation previously exposed to gamma radiation. These results showed that those dosimeters not exposed previously to gamma radiation did not presented any Tl signal. Meanwhile, those previously submitted to gamma irradiation showed that their sensitivity was increased as the gamma dose increased. The glow curve of sensitized KMgF{sub 3}: Lu + Ptfe exposed to UV radiation, presented the dosimetric pea at 212 C. This makes this material to be promissory for measuring UV radiation. (Author)

Beryllium implant activation and damage recovery study in n-type GaSb

Science.gov (United States)

Rahimi, N.; Behzadirad, M.; Renteria, Emma J.; Shima, D. M.; Muniz, Ayse J.; Busani, T.; Lavrova, Olga; Balakrishnan, G.; Lester, L. F.

2014-03-01

Damage induced by the implantation of beryllium in n-type GaSb and its removal by Rapid Thermal Annealing (RTA) are studied in detail by Atomic Force Microscopy (AFM), Cross Sectional Transmission Electron Microscopy (XTEM) and Energy Dispersive X-ray Spectroscopy (EDS). RTA has been implemented with different times and temperatures in order to optimize ion activation and to avoid Sb outdiffusion during the process. Results indicate a lattice quality that is close to pristine GaSb for samples annealed at 600 °C for 10s using a thick Si3N4 capping layer. Electrical response of the implanted diodes is measured and characterized as function of different annealing conditions.

Dosimetric characterization and identification of TL defect centres in sand for its application in sludge irradiators as an in situ dosimeter

International Nuclear Information System (INIS)

Benny, P.G.; Shah, M.R.; Sabharwal, S.; Bhatt, B.C.; Gundu Rao, T.K.

2003-08-01

The report presents investigations that have been carried out to establish a method for the routine/ periodic dosimetry for Sludge Hygienisation Research Irradiator (SHRI) facility set up at Baroda (India) for disinfection of liquid sewage sludge in bulk quantity. For this purpose, the possibility of using the sand, one of the components of inorganic matter found in sewage sludge, directly as a TL dosimeter has been explored. The report is presented in two parts. Part 1 presents dosimetric characterization of sand for its application as an in situ dosimeter. A review on various sewage sludge irradiators operating in the world and the different dosimetric techniques used for these facilities are briefly described. In the present studies, in order to investigate the thermoluminescence properties of sand, it was separated from the sewage sludge by an extensive cleaning procedure. Part 1 also describes the procedure for separation of sand from sewage sludge, study on its TL properties, dosimetric characterization of sand and application of cleaned sand collected at the outlet of the SHRI facility for estimating radiation absorbed dose imparted to the sludge during its disinfection as well as for determining distribution of dose for an irradiated sludge batch. A new method by using phototransferred thermoluminescence (PTTL) in quartz separated from sand has been explored for high-level gamma dosimetry. Part 2 of the report presents sensitization properties of TL peaks and study of TL defect centres in quartz. It describes the results on pre-dose sensitization of 220 degC and 110 degC TL peaks in the quartz samples separated from sand. From the TL and ESR studies, a mechanism for TL sensitization has been suggested, which involves the role of competing traps and E I - centres in the sensitization process. The paramagnetic radicals formed in quartz samples after gamma irradiation by using ESR technique have been briefly described. (author)

Applicability of a portable CdTe and NaI (Tl) spectrometer for activity measure

International Nuclear Information System (INIS)

Fernandes, Jaquiel Salvi

2005-02-01

In this work it was studied the application of an in situ gamma spectrometer (ROVER) of Amptek Inc., composed by a Cadmium Telluride detector (CdTe) of 3 mm x 3 mm x 1 mm and a 30 mm x 30 mm Sodium Iodide detector doped with Thallium [NaI (Tl)). The radioactive sources used were type pastille, sealed in aluminum and polyethylene, of 241 Am, 133 Ba, 152 Eu, 3 sources of 137 Cs and soil samples contaminated with 137 Cs. It was performed a factorial planning 2 3 to optimize the in situ spectrometry system. This way it was determined that the best temperature for CdTe crystal operation is -22, deg C, with Shaping Time of 3 μS and Rise Time Discrimination (RTD) with value 3. With the help of the certified radioactive sources, we determined the efficiency curve of the two detectors. The CdTe detector was positioned at the standard distance of 1 meter of the sources and also at 4.15 cm. The NaI (Tl) detector was also positioned at the standard distance of 1 meter of the sources and at 2.8 cm. Measures were performed to determine the Minimum Detectable Activity (MDA) for both detectors. For the pastille type sources, the 137 Cs MDA for the CdTe detector at 4.15 cm, analyzing the energy line of 32 keV, was 6 kBq and at 1 meter of the 137 Cs source, analyzing the line of 661.65 keV, the MDA was 67 kBq. For soil samples, CdTe detector at 4.15 cm presented a MDA of 693 kBq.kg-l for the line of 32 keV, and for the soil sample 7 Be content the MDA found was 2867 Bq.kg -1 at 4.15 cm. For the NaI (Tl) detector, analyzing the line of 661.65 keV, the 137 Cs MDA for pastille type source at 1 meter of distance was 7 kBq, and for soil sample at 2.8 cm the measured 137 Cs MDA was 71 Bq.kg -1 . For the soil sample 7 Be content, at 2.8 cm of the Nal (Tl) detector, the obtained MDA was 91 Bq.kg -1 . Due to the minimum detectable activities found for the two detectors, we concluded that the employed in situ gamma ray spectrometer system allows the quantification of 137 Cs and 7 Be

Annual dose measurements and TL-dating of ancient Egyptian pottery

Energy Technology Data Exchange (ETDEWEB)

Abdel-Wahab, M S; El-Fiki, S A; Abdel-Kariem, S; El-Faramawy, N [Ain Shams University, Cairo (Egypt). Faculty of Science; EL-Fiki, M A [National Institute of Standards, Cairo (Egypt); Gomaa, M [Atomic Energy Establishment, Cairo (Egypt). Nuclear Research Center

1996-05-01

In the course of the dating of ancient Egyptian pottery, pottery sherds were collected from three archaeological tombs in Nazlet El Samman region, Giza zone (Egypt). The annual dose from natural background was measured by gamma spectrosocopic technique as well as thermoluminescence (TL) measurements. The results of both methods are in good agreement with a consistency of 99.69%. The extracted quartz exhibited TL dating peaks at about (305 {+-} 5){sup o}C. The TL dating shows an age of 4301 {+-} 100 years for the examined pottery which belongs to the ``Fourth Dynasty`` in the ``OlKingdom`` . The uncertainties in TL dating using the additive method are much lower than that of archaeologists. (author).

Annual dose measurements and TL-dating of ancient Egyptian pottery

Science.gov (United States)

Abdel-Wahab, M. S.; El-Fiki, S. A.; El-Fiki, M. A.; Gomaa, M.; Abdel-Kariem, S.; El-Faramawy, N.

1996-05-01

In the course of the dating of ancient Egyptian pottery, pottery sherds were collected from three archaeological tombs in Nazlet El Samman region, Giza zone (Egypt). The annual dose from natural background was measured by gamma spectroscopic technique as well as thermoluminescence (TL) measurements. The results of both methods are in good agreement with a consistency of 99.69%. The extracted quartz exhibited TL dating peaks at about(305 ± 5|4)°C. The TL dating shows an age of 4301 ± 100 years for the examined pottery which belongs to the "Fourth Dynasty" in the "Old Kingdom". The uncertainties in TL dating using the additive method are much lower than that of archeologists.

Annual dose measurements and TL-dating of ancient Egyptian pottery

International Nuclear Information System (INIS)

Abdel-Wahab, M.S.; El-Fiki, S.A.; Abdel-Kariem, S.; El-Faramawy, N.; Gomaa, M.

1996-01-01

In the course of the dating of ancient Egyptian pottery, pottery sherds were collected from three archaeological tombs in Nazlet El Samman region, Giza zone (Egypt). The annual dose from natural background was measured by gamma spectrosocopic technique as well as thermoluminescence (TL) measurements. The results of both methods are in good agreement with a consistency of 99.69%. The extracted quartz exhibited TL dating peaks at about (305 ± 5) o C. The TL dating shows an age of 4301 ± 100 years for the examined pottery which belongs to the ''Fourth Dynasty'' in the ''OlKingdom'' . The uncertainties in TL dating using the additive method are much lower than that of archaeologists. (author)

Study of /sup 201/Tl uptake by bone and bone marrow on /sup 201/Tl scintigraphy. With special reference to bone marrow abnormalities

Energy Technology Data Exchange (ETDEWEB)

Fujii, Tadashige; Tanaka, Masao; Hirose, Yoshiki; Hirayama, Jiro; Handa, Kenjiro; Nakanishi, Fumiko; Yano, Kesato; Ueda, Hitoshi

1989-04-01

Thallium-201 (Tl-201) uptake in the bone and bone marrow was examined in a total of 93 patients with various diseases. Sternal uptake of Tl-201 was observed when patients had bone marrow abnormality especially associated with hematopoietic disease. It was associated with proliferation of immature cells and of various types of bone marrow cells, especially erythroblastic and plasma cells. Whole-body Tl-201 scanning showed a high uptake (82%) in the sternum, chest, lumbar vertebrae, and pelvis. Thallium-201 was definitively taken up by the sternum in polycythemia (5/41), hemolytic anemia (2/2), iron deficiency anemia (2/2), and multiple myeloma (2/5). For leukemia, Tl-201 uptake was slight or negative. Thallium-201 scanning proved useful in visualizing bone marrow abnormality, although careful interpretation of bone and bone marrow uptake is required. (Namekawa, K).

On the tin impurity in the thermoelectric compound ZnSb: Charge-carrier generation and compensation

Energy Technology Data Exchange (ETDEWEB)

Prokofieva, L. V., E-mail: lprokofieva496@gmail.com; Konstantinov, P. P.; Shabaldin, A. A. [Russian Academy of Sciences, Ioffe Physical–Technical Institute (Russian Federation)

2016-06-15

The technique for measuring the Hall coefficient and electrical conductivity in the thermal cycling mode is used to study the effect of the Sn impurity on the microstructure and properties of pressed ZnSb samples. Tin was introduced as an excess component (0.1 and 0.2 at %) and as a substitutional impurity for Zn and Sb atoms in a concentration of (2–2.5) at % The temperature dependences of the parameters of lightly doped samples are fundamentally like similar curves for ZnSb with 0.1 at % of Cu. The highest Hall concentration, 1.4 × 10{sup 19} cm{sup –3} at 300 K, is obtained upon the introduction of 0.1 at % of Sn; the dimensionless thermoelectric figure of merit attains its maximum value of 0.85 at 660 K. The experimental data are discussed under the assumption of two doping mechanisms, which are effective in different temperature ranges, with zinc vacancies playing the decisive role of acceptor centers. In two ZnSb samples with SnSb and ZnSn additives, the charge-carrier compensation effect is observed; this effect depends on temperature and markedly changes with doping type. As in p-type A{sup IV}–B{sup VI} materials with a low Sn content, hole compensation can be attributed to atomic recharging Sn{sup 2+} → Sn{sup 4+}. Types of compensating complexes are considered.

Leading the Charge for SoTL--Embracing Collaboration

Science.gov (United States)

Cassard, Anita; Sloboda, Brian

2014-01-01

The scholarship of teaching and learning (SoTL) enables colleges and universities to assess student learning and measure the outcomes by engaging in meaningful research, and to disseminate this research. The objective of this paper is to give a snapshot of and assess the current thinking behind this scholarship by presenting examples of SoTL, and…

Light yield of a CsI(Tl) crystal under irradiation by protons with the energy from 3 to 15 MeV

International Nuclear Information System (INIS)

Dorchoman, D.; Konstantin, M.; Lazarovich, D.; Muntyanu, I.; Oganesyan, K.O.; Porokhovoj, S.Yu.

1976-01-01

Measurement results are presented of light yield in CsI(Tl) crystals at the irradiation by protons with the energy from 3 to 15 MeV. Plates of 100x100x2 mm size are used as CsI(Tl) scintillator samples. A brief analysis of possible sistematic errors is given which allows to estimate the total error upon the light yield valve determination equal to 0,5%. Measurement results of crystal light yield show that the dependence of CsI(Tl) light yield on proton energy is described by the straight line passing through the origin

Real-time in-situ monitoring of the topotactic transformation of TlCu3Se2 into TlCu2Se2

International Nuclear Information System (INIS)

Ångström, J.; Sahlberg, M.; Berger, R.

2015-01-01

Highlights: • Topotactic transition from TlCu 3 Se 2 to TlCu 2 Se 2 followed in situ. • Synchrotron radiation X-ray powder diffraction enabled short scans. • Relative abundance of phases refined from powder data. • Opens up for studying similar systems in the same manner. - Abstract: The solid state transformation of monoclinic TlCu 3 Se 2 into tetragonal TlCu 2 Se 2 by oxidative copper leaching in concentrated ammonia solution has been studied in situ by the use of synchrotron radiation. The diffraction patterns of parent and daughter phase are both sharp, indicating a strong topotactic relationship between them that effectuates a rapid change by “chimie douce” performed at +19 °C. The transformation rate is strongly connected to the access of oxygen from the surrounding air. The transformation was followed in a real-time mode, being almost complete after 2.5 h with 1 h incubation due to low oxygen content, as shown from refining the diffraction patterns by Rietveld profile technique

TL/OSL ages from Salto Formation (Uruguay)tectonic, climatic and environmental considerations

International Nuclear Information System (INIS)

Ubilla, M.; Veroslavsky, G.

2004-01-01

TL/OSL ages from Salto Formation based on two sandy samples collected at Salto City and Route 3 (Boycua Creek) are provided: 986±100 ky (LVD-948) and 830±95 ky (LVD-949) respectively. Both support a Pleistocene age for Salto Formation, approximately late early/early middle Pleistocene. Neotectonic and climatic processes are also discussed [es

Microcomputer-Controlled Reader Systems for Archaeological and Geological TL Dating

DEFF Research Database (Denmark)

Bøtter-Jensen, Lars; Mejdahl, V.

1984-01-01

Two fully automated TL reader systems for TL dating and a manually operated reader for research purpose were put into operation during 1982-3. All systems are controlled by HP-85 or HP-86 microcomputers; thus flexibility in selection of measurement parameters, calculation of TL signals and displa...... the archaeological and geological ages. The principle of the measurement procedures are described, and dating results are presented to illustrate the performance of the systems...

Tl-201 and Tc-99m-DTPA neuro-SPECT in cerebral radiation necrosis

International Nuclear Information System (INIS)

Cleto, E.M. Jr.; Holmes, R.A.; Gumerlock, M.K.; Cabeen, M.; Logan, K.W.; Hoffman, T.J.

1992-01-01

The results in 3 cases of radiation necrosis demonstrate that by using both radionuclides Tl-201 and Tc-99m-DTPA, one can provide a semi-quantitative method to differentiate recurrent tumor from radiation necrosis. Focally increased cerebral Tl-201 activity in irradiated brain tumor patients is not specific for tumor recurrence, but when used in combination with DTPA, one is able to estimate the amount of Tl-201 activity resulting from increased blood-brain barrier permeability. If the average Tl-201 index is less than the average Tc-99m-DTPA index it suggests that the increased Tl-201 activity results primarily from blood-brain barrier breakdown. Tc-99m-DTPA SPECT, in addition to Tl-201 SPECT, or serial Tl-201 SPECT imaging may increase the accuracy of brain scintigraphy in differentiating radiation necrosis from tumor recurrence. To verify these preliminary findings, we are in the process of analyzing additional SPECT data on 9 more patients with malignant brain tumors. Using a slightly different method of quantifying Tl- 201/Tc-99m-DTPA ratios (computing the ratio of intralesional Tl-201 or Tc-99m-DTPA activity compared to adjacent scalp activity), patients with tumor recurrence have higher Tl-201/Tc-99m-DTPA ratios compared to those with radiation necrosis (verbal communication with Dr. Mary K. Gumerlock). (orig.) [de

Benchmarking NaI(Tl) Electron Energy Resolution Measurements

International Nuclear Information System (INIS)

Mengesha, Wondwosen; Valentine, J D.

2002-01-01

A technique for validating electron energy resolution results measured using the modified Compton coincidence technique (MCCT) has been developed. This technique relies on comparing measured gamma-ray energy resolution with calculated values that were determined using the measured electron energy resolution results. These gamma-ray energy resolution calculations were based on Monte Carlo photon transport simulations, the measured NaI(Tl) electron response, a simplified cascade sequence, and the measured electron energy resolution results. To demonstrate this technique, MCCT-measured NaI(Tl) electron energy resolution results were used along with measured gamma-ray energy resolution results from the same NaI(Tl) crystal. Agreement to within 5% was observed for all energies considered between the calculated and measured gamma-ray energy resolution results for the NaI(Tl) crystal characterized. The calculated gamma-ray energy resolution results were also compared with previously published gamma-ray energy resolution measurements with good agreement (<10%). In addition to describing the validation technique that was developed in this study and the results, a brief review of the electron energy resolution measurements made using the MCCT is provided. Based on the results of this study, it is believed that the MCCT-measured electron energy resolution results are reliable. Thus, the MCCT and this validation technique can be used in the future to characterize the electron energy resolution of other scintillators and to determine NaI(Tl) intrinsic energy resolution

Effects of ischemic-like insult on myocardial 201Tl accumulation

International Nuclear Information System (INIS)

Goldhaber, S.Z.; Newell, J.B.; Alpert, N.M.; Andrews, E.; Pohost, G.M.; Ingwall, J.S.

1983-01-01

Despite extensive clinical use of thallium-201 ( 201 Tl) for myocardial imaging, the effect of ischemia on myocardial accumulation and release of 201 Tl independent of flow has not been fully defined. Therefore, myocardial accumulation of 201 Tl in response to ischemic-like myocardial injury was assessed in vitro using the cultured fetal mouse heart preparation. Cultured fetal mouse hearts (n . 311) were subjected to injury simulating ischemia by deprivation of oxygen and oxidizable substrates for periods ranging from 15 minutes to 10 hours. The extent of irreversible injury was determined by the percentage of lactic dehydrogenase (LDH) lost from the hearts to the culture medium during recovery from injury. Injury was essentially reversible at 1 hour of insult. The fraction of 201 Tl content in injured compared with control hearts was not significantly lower after 1 hour of insult. By 3 hours of insult, irreversible injury as assessed by loss of LDH was detectable and the extent of injury increased progressively through 10 hours. During the 3-10-hour period of irreversible injury, 201 Tl accumulation within injured hearts compared with controls was related in a monotonically decreasing fashion to the loss of LDH as described by a mathematical kinetic model that fit the observations closely (R2 greater than 0.99). These results indicate that in this organ culture preparation, in which there is effectively an unlimited reservoir of 201 Tl and no confounding effects of perfusion, the time-dependent 201 Tl accumulation is determined by the extent of irreversible injury

Sb{sub 7}Te{sub 3}/ZnSb multilayer thin films for high thermal stability and long data retention phase-change memory

Energy Technology Data Exchange (ETDEWEB)

Chen, Shiyu; Wu, Weihua [Functional Materials Research Laboratory, School of Materials Science & Engineering, Tongji University, Shanghai 201804 (China); Zhai, Jiwei, E-mail: apzhai@tongji.edu.cn [Functional Materials Research Laboratory, School of Materials Science & Engineering, Tongji University, Shanghai 201804 (China); Song, Sannian; Song, Zhitang [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Micro-system and Information Technology, Chinese Academy of Science, Shanghai 200050 (China)

2017-04-15

Highlights: • Sb{sub 7}Te{sub 3} (ST) provides a fast crystallization speed, low melting temperature. • The Sb{sub 7}Te{sub 3}/ZnSb films exhibits faster crystallization speed, high thermal stability. • The calculated temperature for 10-year data retention is about 127 {sup o}C. • The Sb{sub 7}Te{sub 3}/ZnSb multilayer configuration with low power consumption. - Abstract: Phase-change memory is regard as one of the most promising candidates for the next-generation non-volatile memory. In this work, we proposed a Sb{sub 7}Te{sub 3}/ZnSb multilayer thin films to improve the thermal stability of Sb-rich Sb{sub 3}Te{sub 7}. The sheet resistance ratio between amorphous and crystalline states reached up to 4 orders of magnitude. With regard to the thermal stability, the calculated temperature for 10-year data retention is about 127 °C. The threshold current and threshold voltage of a cell based on Sb{sub 7}Te{sub 3}/ZnSb are 6.9 μA and 1.9 V, respectively. The lower RESET power is presented in the PCM cells of Sb{sub 7}Te{sub 3}/ZnSb films, benefiting from its high resistivity.

Standardization of 125 Sb in equilibrium non-equilibrium situations with 125m Te

International Nuclear Information System (INIS)

Rodriguez Barquero, L.; Jimenez de Mingo, A.; Grau Carles, A.

1997-10-01

We study the stability of ''125 Sb in the following scintillators: HiSafeIII''TM, Insta- Gel reg s ign Plus and '' Ultima-Gold'' TM. Since ''125 m Te requires more than one year to reach the secular equilibrium with ''125 Sb, we cannot be sure, for a given sample, whether equilibrium is reached or not. In this report we present a new procedure that permits one calibrate mixtures of ''125 Sb+''125 m Te out of the equilibrium. The steps required for the radiochemical separation of the components are indicated. Finally, we study the evolution of counting rate when column yields are less than 100%. (Author)

Qualitative analysis of Th-232 in soil samples with portable radiological identifiers NaI (Tl) and LaBr{sub 3} (Ce); Análise qualitativa de Th-232 em amostras de solo com identificadores radiológicos portáteis NaI(Tl) e LaBr{sub 3}(Ce)

Energy Technology Data Exchange (ETDEWEB)

Oliveira, L.S.R.; Amorim, A.S.; Balthar, M.C.V.; Vilela, P.RT.; Santos, A. [Instituto de Defesa, Química, Biológica, Radiológica e Nuclear (IDQBRN), Rio de Janeiro, RJ (Brazil); Cardoso, D.O.; Izidoro, A.C.A.C. [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil); Pelegrineli, S.Q.; Silva, L.B.; Silva, S.L. [MAXIM Treinamento e Assessoria, Rio de Janeiro, RJ (Brazil); Santos, F.R.; Ribeiro, C.A.M.; Silva, D.C., E-mail: lucianosantarita@gmail.com, E-mail: domingosoliveiralvr71@gmail.com, E-mail: samuelfisica@yahoo.com.br [Universidade Estácio de Sá, Rio de Janeiro, RJ (Brazil)

2017-07-01

The identification of the occurrence of Th-232 in open environments using portable radiological identifiers (IRP) with scintillators, discriminating the environmental condition and NORM is important for the operational teams of the Institute of Chemical, Biological, Radiological and Nuclear Defense (IDQBRN) of the Army. The qualitative analysis by gamma energy spectrometry for the energies of Th-232 and its daughter radioisotopes, given the resolution that characterizes the scintillation crystals (NaI (Tl) - 7.5% and LaBr{sub 3} (Ce) - 2.9%) makes it possible to identify them. The purpose is to perform a qualitative analysis of the reliability of the response of these IRPs to the measurements of Th-232 generally found in the environment and in samples extracted from points where the thorium concentration is highest. The results show that the identification of this radionuclide by the IRP in the samples with the highest natural occurrence is achieved by measuring the energies of the daughter isotopes Ac-228, Tl-208, Bi-212 and Pb-212 allowing the discrimination of soils with natural occurrence of Th -232 and NORM. These measurements will be based on the procedures used by the operational teams in the field actions aimed at reducing exposure to this radiation, both for individuals occupationally exposed and for the population.

(In)GaSb/AlGaSb quantum wells grown on Si substrates

International Nuclear Information System (INIS)

Akahane, Kouichi; Yamamoto, Naokatsu; Gozu, Shin-ichiro; Ueta, Akio; Ohtani, Naoki

2007-01-01

We have successfully grown GaSb and InGaSb quantum wells (QW) on a Si(001) substrate, and evaluated their optical properties using photoluminescence (PL). The PL emissions from the QWs at room temperature were observed at around 1.55 μm, which is suitable for fiber optic communications systems. The measured ground state energy of each QW matched well with the theoretical value calculated by solving the Schroedinger equation for a finite potential QW. The temperature dependence of the PL intensity showed large activation energy (∼ 77.6 meV) from QW. The results indicated that the fabricated QW structure had a high crystalline quality, and the GaSb QW on Si for optical devices operating at temperatures higher than room temperature will be expected

Systems Tl2MoO4-E(MoO4)2, where E=Zr or Hf, and the crystal structure of Tl8Hf(MoO4)6

International Nuclear Information System (INIS)

Bazarov, B.G.; Bazarova, Ts.T.; Fedorov, K.N.; Bazarova, Zh.G.; Chimitova, O.D.; Klevtsova, R.F.; Glinskaya, L.A.

2006-01-01

Systems Tl 2 MoO 4 -E(MoO 4 ) 2 (E=Zr, Hf) were studied by X-ray diffraction, differential thermal analysis and IR spectroscopy. Formation of Tl 8 E(MoO 4 ) 6 and Tl 2 E(MoO 4 ) 2 compounds was established. Phase T-x diagrams of the Tl 2 MoO 4 -Zr(MoO 4 ) 2 system were constructed. Monocrystals were grown, and structure of Tl 8 Hf(MoO 4 ) 6 was studied. The compound is crystallized in monoclinic syngony with elementary cell parameters a=9.9688(6), b=18.830(1), c=7.8488(5) A, β=108.538(1) Deg, Z=2, sp. gr. C2/m. The isolated group [HfMo 6 O 24 ] 8- is responsible for fundamental fragment of the structure. Three varieties of crystallographically independent Tl-polyhedra fill space evenly between fragments [HfMo 6 O 24 ] 8- forming three-dimensional form [ru

Sb(V reactivity with human blood components: redox effects.

Directory of Open Access Journals (Sweden)

Silvana López

Full Text Available We assessed the reactivity of Sb(V in human blood. Sb(V reactivity was determined using an HPLC-HG-AFS hyphenated system. Sb(V was partially reduced to Sb(III in blood incubation experiments; however, Sb(III was a highly unstable species. The addition of 0.1 mol L(-1 EDTA prevented Sb(III oxidation, thus enabling the detection of the reduction of Sb(V to Sb(III. The transformation of Sb(V to Sb(III in human whole blood was assessed because the reduction of Sb(V in human blood may likely generate redox side effects. Our results indicate that glutathione was the reducing agent in this reaction and that Sb(V significantly decreased the GSH/GSSG ratio from 0.32 ± 0.09 to 0.07 ± 0.03. Moreover, the presence of 200 ng mL(-1 of Sb(V increased the activity of superoxide dismutase from 4.4 ± 0.1 to 7.0 ± 0.4 U mL(-1 and decreased the activity of glutathione peroxidase from 62 ± 1 to 34 ± 2 nmol min(-1 mL(-1.

A preliminary study of landslide gouge dating by TL technique

Energy Technology Data Exchange (ETDEWEB)

Fengju, Ji; Jianping, Li [Inst. of Geology, National Seismological Bereau, Beijing (China); Mingda, Liu [Inst. of Crustal Dynamics, SSB, Beijing (China)

1993-04-01

The key to date slipping of landslide by TL method is whether the temperature and pressure caused by slipping can lead the original TL to 'zero'for some minerals within the slipping band. For this purpose, the simulated experiments under different temperature-pressure were made and the TL annealing effect of landslide gouge was studied. The results show that the frictional heating caused during slipping is a main factor leading the mineral's TL to decrease on the slip plane and that increment of temperature is in close relation with strength of shear stress, thickness of landslide gouge and amount of displacement. As an example, the slipping age of a paleo-landslide at Huangtupo, Hubei Province, has been dated to be about 140 ka.

Dielectric and baric characteristics of TlS single crystal

Energy Technology Data Exchange (ETDEWEB)

Mustafaeva, S.N., E-mail: solmust@gmail.com [Institute of Physics, ANAS, G. Javid prosp. 33, Az 1143 Baku (Azerbaijan); Asadov, M.M. [Institute of Chemical Problems, ANAS, G. Javid prosp. 29, Az 1143 Baku (Azerbaijan); Ismailov, A.A. [Institute of Physics, ANAS, G. Javid prosp. 33, Az 1143 Baku (Azerbaijan)

2014-11-15

The investigation of the frequency dependences of the dielectric coefficients and ac-conductivity of the TlS single crystals made it possible to elucidate the nature of dielectric loss and the charge transfer mechanism. Moreover, we evaluated the density and energy spread of localized states near the Fermi level, the average hopping time and the average hopping length. It was shown that the dc-conductivity of the TlS single crystals can be controlled by varying the hydrostatic pressure. This has opened up possibilities for using TlS single crystals as active elements of pressure detectors.

Phase equilibria in TlX-Cd(Zn)X (X-S, Se, Te) systems

International Nuclear Information System (INIS)

Gusejnov, F.Kh.; Babanly, M.B.; Kuliev, A.A.

1982-01-01

The methods of DTA, RPA and measurement of the alloys microhardness have been used to investigate the phase equilibria in the TlX-Zn(Cd)X systems. It is established that the TlZn(Cd)X 2 compounds, the presence of which is mentioned in the literature earlier, do not form in these systems. The TlSe-Zn(Cd)Se systems apply to the simple eutectic type and characterized by digenerated eutectic near the TlSe. Thermodynamical analysis of the liquidus of the TlSe-CdSe and TlTe-Zn(Cd)Te systems in approximation of the regular solutions, taking into account the dissociation of tallium chalcogenides in liquid phase, is made

Analysis Of DWPF Sludge Batch 7A (Macrobatch 8) Pour Stream Samples

International Nuclear Information System (INIS)

Johnson, F.

2012-01-01

The Defense Waste Processing Facility (DWPF) began processing Sludge Batch 7a (SB7a), also referred to as Macrobatch 8 (MB8), in June 2011. SB7a is a blend of the heel of Tank 40 from Sludge Batch 6 (SB6) and the SB7a material that was transferred to Tank 40 from Tank 51. SB7a was processed using Frit 418. During processing of each sludge batch, the DWPF is required to take at least one glass sample to meet the objectives of the Glass Product Control Program (GPCP), which is governed by the DWPF Waste Compliance Plan, and to complete the necessary Production Records so that the final glass product may be disposed of at a Federal Repository. Three pour stream glass samples and two Melter Feed Tank (MFT) slurry samples were collected while processing SB7a. These additional samples were taken during SB7a to understand the impact of antifoam and the melter bubblers on glass redox chemistry. The samples were transferred to the Savannah River National Laboratory (SRNL) where they were analyzed. The following conclusions were drawn from the analytical results provided in this report: (1) The sum of oxides for the official SB7a pour stream glass is within the Product Composition Control System (PCCS) limits (95-105 wt%). (2) The average calculated Waste Dilution Factor (WDF) for SB7a is 2.3. In general, the measured radionuclide content of the official SB7a pour stream glass is in good agreement with the calculated values from the Tank 40 dried sludge results from the SB7a Waste Acceptance Program Specification (WAPS) sample. (3) As in previous pour stream samples, ruthenium and rhodium inclusions were detected by Scanning Electron Microscopy-Electron Dispersive Spectroscopy (SEM-EDS) in the official SB7a pour stream sample. (4) The Product Consistency Test (PCT) results indicate that the official SB7a pour stream glass meets the waste acceptance criteria for durability with a normalized boron release of 0.64 g/L, which is an order of magnitude less than the Environmental

Effects of buffer layer on the structural and electrical properties of InAsSb epilayers grown on GaAs(001)

International Nuclear Information System (INIS)

Jayavel, P.; Nakamura, S.; Koyama, T.; Hayakawa, Y.

2006-01-01

InAsSb ternary epilayers with arsenic composition of 0.5 have been grown on GaAs(001) substrates. Linear-graded and step-graded InAsSb buffer layers with an InSb layer have been used to relax lattice mismatch between the epilayer and substrate. X-ray diffraction results of the epilayers indicate that an enhancement in the peak intensity of the buffer layer samples is due to improved crystalline quality of the epilayers. We find that the growth technique of the buffer layer strongly influences the surface morphology and roughness of the epilayer. Hall effect measurements of the step-graded buffer layer samples show an order of magnitude higher electron mobility than the direct and linear-graded buffer layer samples. These results demonstrate that high crystalline quality and electron mobility of the InAs 0.5 Sb 0.5 ternary epilayers can be achieved by using the step-graded InAsSb buffer layers. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Very low background gamma spectrometer mounted in anti-Compton with NaI(Tl) for the study of glaciers and sediment samples; Spectrometrie gamma a tres bas niveau avec anti-Compton NaI(Tl), pour l`etude des glaciers et des sediments

Energy Technology Data Exchange (ETDEWEB)

Pinglot, J.F.; Pourchet, M. [Centre National de la Recherche Scientifique (CNRS), 38 - Grenoble (France). Lab. de Glaciologie

1994-05-01

The determination of natural and artificial radioactivities of snow (glaciers, polar ice-caps) or sediment samples (lakes, oceans), takes great benefit with the use of the superior resolution of high purity germanium detector, N type, in a broad energy range( 10 keV up to 1.6 MeV). This detector (relative efficiency: 20%), very low background specified, is mounted in anti-Compton with a 9`x 8` NaI(Tl) scintillator, also with low background. International standards, used with a quantitative software allows the determination of the efficiency curve and the isotopes identification and specific activity. The anti-Compton suppressed spectrometer exhibits a decrease of the background by a factor of ten, without any change in efficiencies. Applications of this spectrometer deal with samples from lake Titicaca and a glacier from Spitsbergen. (authors). 6 figs., 7 refs.

Expanding the Teaching Commons: Making the Case for a New Perspective on SoTL

Directory of Open Access Journals (Sweden)

Kim A. Case, PhD

2013-08-01

Full Text Available As a reflection on O’Meara, Terosky, and Neumann’s (2011 work on scholarship of teaching and learning (SoTL faculty development, this essay describes the benefits of SoTL to individual faculty and university goals. In support and expansion of arguments advanced by O’Meara et al., this work calls for the use of SoTL faculty development to promote the shared teaching commons, active recruitment of new SoTL scholars, institutionalization of SoTL values, and integration of SoTL initiatives in both teaching centers and research-focused development offices.

Si-Sb-Te materials for phase change memory applications

International Nuclear Information System (INIS)

Rao Feng; Song Zhitang; Ren Kun; Zhou Xilin; Cheng Yan; Wu Liangcai; Liu Bo

2011-01-01

Si-Sb-Te materials including Te-rich Si 2 Sb 2 Te 6 and Si x Sb 2 Te 3 with different Si contents have been systemically studied with the aim of finding the most suitable Si-Sb-Te composition for phase change random access memory (PCRAM) use. Si x Sb 2 Te 3 shows better thermal stability than Ge 2 Sb 2 Te 5 or Si 2 Sb 2 Te 6 in that Si x Sb 2 Te 3 does not have serious Te separation under high annealing temperature. As Si content increases, the data retention ability of Si x Sb 2 Te 3 improves. The 10 years retention temperature for Si 3 Sb 2 Te 3 film is ∼ 393 K, which meets the long-term data storage requirements of automotive electronics. In addition, Si richer Si x Sb 2 Te 3 films also show improvement on thickness change upon annealing and adhesion on SiO 2 substrate compared to those of Ge 2 Sb 2 Te 5 or Si 2 Sb 2 Te 6 films. However, the electrical performance of PCRAM cells based on Si x Sb 2 Te 3 films with x > 3.5 becomes worse in terms of stable and long-term operations. Si x Sb 2 Te 3 materials with 3 < x < 3.5 are proved to be suitable for PCRAM use to ensure good overall performance.

First-principles prediction of Tl/SiC for valleytronics

KAUST Repository

Xu, Zhen; Zhang, Qingyun; Shen, Qian; Cheng, Yingchun; Schwingenschlö gl, Udo; Huang, Wei

2017-01-01

Recently, monolayer Tl on a Si or Ge substrate has been proposed for potential valleytronic systems. However, the band gaps of these systems are less than 0.1 eV, which is too small to be applied because an electric field or magnetic doping will reduce the band gaps further for the systems to become metallic. Here, we investigate SiC as an alternative substrate. By first-principles calculations we demonstrate that monolayer Tl can be grown on SiC. There are two valleys around the K/K′ points and the Berry curvature shows that the two valleys are inequivalent, indicating valley pseudospin. Moreover, due to the larger band gap of SiC (3.3 eV), the band gap of the Tl/SiC system is 0.6 eV, which is large enough for valley manipulation. Furthermore, we demonstrate that Cr doping can achieve valley polarization. Our study shows that the Tl/SiC system is promising for valleytronic applications.

First-principles prediction of Tl/SiC for valleytronics

KAUST Repository

Xu, Zhen

2017-09-22

Recently, monolayer Tl on a Si or Ge substrate has been proposed for potential valleytronic systems. However, the band gaps of these systems are less than 0.1 eV, which is too small to be applied because an electric field or magnetic doping will reduce the band gaps further for the systems to become metallic. Here, we investigate SiC as an alternative substrate. By first-principles calculations we demonstrate that monolayer Tl can be grown on SiC. There are two valleys around the K/K′ points and the Berry curvature shows that the two valleys are inequivalent, indicating valley pseudospin. Moreover, due to the larger band gap of SiC (3.3 eV), the band gap of the Tl/SiC system is 0.6 eV, which is large enough for valley manipulation. Furthermore, we demonstrate that Cr doping can achieve valley polarization. Our study shows that the Tl/SiC system is promising for valleytronic applications.

Effect of Sb and Si doping on the superconducting properties of FeSe0.9

International Nuclear Information System (INIS)

Sudesh,; Rani, S.; Varma, G.D.

2013-01-01

Highlights: ► We synthesized all the samples using two-step solid state reaction method. ► Si and Sb doping is done at the Se site of the compound FeSe 0.9 . ► H c2 (0) is calculated with GL-Fit and also using WHH model. ► Behavior of activation energy is studied with applied field. -- Abstract: In the present work, we have studied the effect of doping Sb and Si at the Se-site of FeSe 0.9 on the superconducting properties, such as transition temperature (T c ), upper critical field (H c2 ) and irreversibility field (H irr ). The polycrystalline samples have been synthesized via two step solid state reaction route with nominal compositions Fe[Se 1−x (Sb/Si) x ] 0.9 (x = 0.0, 0.05, 0.10, 0.15 and 0.20). The X-ray diffraction results show the presence of tetragonal α-FeSe phase with the P4/nmm space group symmetry in all the samples. The highest superconducting onset temperatures, T c onset ∼9.42Kand9.20K, respectively, for Si and Sb doped samples have been found for x = 0.05. The temperature dependence of H c2 (T) and H irr (T) have been calculated from the magnetoresistance data using the criteria of 90% and 10% of normal state resistivity (ρ n ) values, respectively. The values of H c2 (0) estimated from Werthamer–Helfand–Hohenberg (WHH) and Ginzburg–Landau (GL) theories are found to follow the same trends and maximum H c2 (0) is found for the composition x = 0.10 for both the Si and Sb doped samples. The irreversibility field, H irr and activation energy, U 0 have also been calculated to study the vortex motion behavior of the samples. A clear cut correlation between H irr and U 0 has been found

Myocardial viability assessed by Tl-201 SPECT. Redistribution versus reinjection

International Nuclear Information System (INIS)

Chalela, William Azem; Pimentel, Flavio Ferrarini de Oliveira; Uchida, Augusto Hiroshi; Bottega, Augusto; Ramires, Jose Antonio Franchine; Izaki, Marisa; Moraes, Aguinaldo Pereira; Soares Junior, Jose; Giorgi, Maria C. Pinto; Moffa, Paulo Jorge; Bellotti, Giovanni; Giovanni Guido Cerri; Meneghetti, Jose Claudio

1994-01-01

The purpose of this study was to verify if a third series of images acquired by reinjection thallium-201, 24 h after conventional myocardial perfusion with the radioisotope, improves the identification of myocardial viability segments. The methods: we studied 30 patients, mean age 57.7 ±9.4 years, with old myocardial infarction using thallium (Tl)-201 SPECT, and we obtained three series of images (stress, redistribution after 4 h and reinjection after 24 h. Cardiac images were divided in 5 segments (apical, lateral, anterior, septal and inferior) and each one received a value by a score system according to the Tl-201 myocardial uptake (0=normal uptake; 1=mild hypoperfusion; 2=moderate hypoperfusion; 3=severe hypoperfusion or no myocardial uptake). We considered viable myocardium when the uptake of Tl-201 in the segment related to te myocardial infarction increases at least 1 point in two different axis of Tl-201 SPECT. The results: seven (23,3%) patients demonstrated increase of Tl-201 uptake only at reinjection images, showing a high efficacy of the method. Nine (30%) patients showed persistent hypoperfusion at all series of images suggesting only fibrosis in the are related to the infarction. Fourteen (46,7%) patients showed increase of Tl-201 concentration at redistribution images; among these patients, six showed improvement of myocardial uptake at reinjection. This condition was interpreted as regional chronic ischemic process: hibernating myocardium. The conclusion was that Tl-201 hypoperfusion at redistribution images without significant changes in relation to the stress images do not represent fibrosis at all. The reinjection technic was better than conventional redistribution in the detection of viable myocardium. This data allows a better therapeutic orientation. (author)

Masses of the components of SB2 binaries observed with Gaia - IV. Accurate SB2 orbits for 14 binaries and masses of three binaries*

Science.gov (United States)

Kiefer, F.; Halbwachs, J.-L.; Lebreton, Y.; Soubiran, C.; Arenou, F.; Pourbaix, D.; Famaey, B.; Guillout, P.; Ibata, R.; Mazeh, T.

2018-02-01

The orbital motion of non-contact double-lined spectroscopic binaries (SB2s), with periods of a few tens of days to several years, holds unique, accurate information on individual stellar masses, which only long-term monitoring can unlock. The combination of radial velocity measurements from high-resolution spectrographs and astrometric measurements from high-precision interferometers allows the derivation of SB2 component masses down to the percent precision. Since 2010, we have observed a large sample of SB2s with the SOPHIE spectrograph at the Observatoire de Haute-Provence, aiming at the derivation of orbital elements with sufficient accuracy to obtain masses of components with relative errors as low as 1 per cent when the astrometric measurements of the Gaia satellite are taken into account. In this paper, we present the results from 6 yr of observations of 14 SB2 systems with periods ranging from 33 to 4185 days. Using the TODMOR algorithm, we computed radial velocities from the spectra and then derived the orbital elements of these binary systems. The minimum masses of the 28 stellar components are then obtained with an average sample accuracy of 1.0 ± 0.2 per cent. Combining the radial velocities with existing interferometric measurements, we derived the masses of the primary and secondary components of HIP 61100, HIP 95995 and HIP 101382 with relative errors for components (A,B) of, respectively, (2.0, 1.7) per cent, (3.7, 3.7) per cent and (0.2, 0.1) per cent. Using the CESAM2K stellar evolution code, we constrained the initial He abundance, age and metallicity for HIP 61100 and HIP 95995.

Crystal growth and characterization of bulk Sb2Te3 topological insulator

Science.gov (United States)

Sultana, Rabia; Gurjar, Ganesh; Patnaik, S.; Awana, V. P. S.

2018-04-01

The Sb2Te3 crystals are grown using the conventional self flux method via solid state reaction route, by melting constituent elements (Sb and Te) at high temperature (850 °C), followed by slow cooling (2 °C/h). As grown Sb2Te3 crystals are analysed for various physical properties by x-ray diffraction (XRD), Raman Spectroscopy, Scanning Electron Microscopy (SEM) coupled with Energy Dispersive x-ray Spectroscopy (EDAX) and electrical measurements under magnetic field (6 Tesla) down to low temperature (2.5 K). The XRD pattern revealed the growth of synthesized Sb2Te3 sample along (00l) plane, whereas the SEM along with EDAX measurements displayed the layered structure with near stoichiometric composition, without foreign contamination. The Raman scattering studies displayed known ({{{{A}}}1{{g}}}1, {{{{E}}}{{g}}}2 and {{{{A}}}1{{g}}}2) vibrational modes for the studied Sb2Te3. The temperature dependent electrical resistivity measurements illustrated the metallic nature of the as grown Sb2Te3 single crystal. Further, the magneto—transport studies represented linear positive magneto-resistance (MR) reaching up to 80% at 2.5 K under an applied field of 6 Tesla. The weak anti localization (WAL) related low field (±2 Tesla) magneto-conductance at low temperatures (2.5 K and 20 K) has been analysed and discussed using the Hikami—Larkin—Nagaoka (HLN) model. Summarily, the short letter reports an easy and versatile method for crystal growth of bulk Sb2Te3 topological insulator (TI) and its brief physical property characterization.

Measurement of radioactive tracer microsphere blood from with NaI(Tl)- and Ge-well type detectors

International Nuclear Information System (INIS)

Winkler, B.; Staemmler, G.; Schaper, W.; Frank, J.; Langsdorf, S.

1982-01-01

An intrinsic Ge-well type detector was applied for the detection of gamma rays from labeled tracer microspheres. The high energy resolution and the large peak-to-Compton ratio of this spectrometer ensures the application of all available differently labeled tracer microspheres in one experiment. The superior energy resolution of the Ge-detector was documented with the separated photopeak regions of 103-Ru and 85-Sr-labeled tracer microspheres, which result in a single photopeak when an NaI(Tl) detector is used. The Ge-well type detector was compared with an NaI(Tl) spectrometer by counting samples of cardiac muscle in either spectrometer systems. Regression analysis between both spectrometer systems demonstrate identical flow values in these samples for 5 differently labeled tracer microspheres which were administered in 5 dogs. The high sensitivity of the Ge-well-type detector together with a suitable technique for sampling of myocardial tissue accomplishes a high spatial resolution of myocardial perfusion for all available differently labeled tracer microspheres. (orig.)

Enhanced electrical transport and thermoelectric properties in Ni doped Cu3SbSe4

Science.gov (United States)

Kumar, Aparabal; Dhama, P.; Das, Anish; Sarkar, Kalyan Jyoti; Banerji, P.

2018-05-01

In this study, we report the enhanced thermoelectric performance of Cu3SbSe4 by Ni doping at Cu site. Cu3-xNixSbSe4 (x = 0, 0.01, 0.03, 0.05) were prepared by melt growth, ball milling followed by spark plasma sintering. Structural characterization, phase analysis and surface morphology were carried out using X-ray diffraction, field emission scanning electron microscopy and energy dispersive X-ray spectroscopy. Electrical and thermal properties of all the samples were investigated in the temperature range 300 - 650 K. Decrease in electrical resistivity with Ni doping due to increase in carrier concentration with enhanced Seebeck coefficient via increase in density of state near the Fermi level gives a remarkably high power factor. At the same time, thermal conductivity was found to decrease due to increased carrier-phonon scattering and acoustic phonon scattering. Consequently, a remarkable enhancement in the thermoelectric figure of merit (ZT˜ 0.65) of Cu3-xNixSbSe4 was achieved for x = 0.01 sample. Thus, Ni doping is an effective approach to improve the efficiency of Cu3SbSe4.

Optimization of growth parameters for MOVPE-grown GaSb and Ga{sub 1-x}In{sub x}Sb

Energy Technology Data Exchange (ETDEWEB)

Miya, S.S.; Wagener, V. [Department of Physics, Private Bag X 77000, Nelson Mandela Metropolitan University, Port Elizabeth 6001 (South Africa); Botha, J.R., E-mail: reinhardt.botha@nmmu.ac.za [Department of Physics, Private Bag X 77000, Nelson Mandela Metropolitan University, Port Elizabeth 6001 (South Africa)

2012-05-15

The triethylgallium/trimethylantimony (TEGa/TMSb) precursor combination was used for the metal-organic vapour phase epitaxial growth of GaSb at a growth temperature of 520 Degree-Sign C at atmospheric pressure. Trimethylindium was added in the case of Ga{sub 1-x}In{sub x}Sb growth. The effects of group V flux to group III flux ratio (V/III ratio) on the crystallinity and optical properties of GaSb layers are reported. It has been observed from the crystalline quality and optical properties that nominal V/III ratios of values greater than unity are required for GaSb epitaxial layers grown at this temperature. It has also been shown that Ga{sub 1-x}In{sub x}Sb can be grown using TEGa as a source of gallium species at atmospheric pressure. The relationship between Ga{sub 1-x}In{sub x}Sb vapour composition and solid composition has been studied at a V/III ratio of 0.78.

Gel-combustion synthesis of CoSb2O6 and its reduction to powdery Sb2Co alloy

Directory of Open Access Journals (Sweden)

MAJA JOVIC

2009-01-01

Full Text Available Sb2Co alloy in powdery form was synthesized via reduction with gaseous hydrogen of the oxide CoSb2O6, obtained by the citrate gel-combustion technique. The precursor was an aqueous solution of antimony nitrate, cobalt nitrate and citric acid. The precursor solution with mole ratio Co(II/Sb(V of 1:2 was gelatinized by evaporation of water. The gel was heated in air up to the temperature of self-ignition. The product of gel combustion was a mixture of oxides and it had to be additionally thermally treated in order to be converted to pure CoSb2O6. The reduction of CoSb2O6 by gaseous hydrogen yielded powdery Sb2Co as the sole phase. The process of oxide reduction to alloy was controlled by thermogravimetry, while X-ray diffractometry was used to control the phase compositions of both the oxides and alloys.

Use of universal functional optimisation for TL glow curve analysis

International Nuclear Information System (INIS)

Pernicka, F.; Linh, H.Q.

1996-01-01

The effective use of any TL instrument requires an efficient software package to be able to fulfil different tasks required by research and practical applications. One of the standard features of the package used at the NPI Prague is the application of the interactive modular system Universal Functional Optimisation (UFO) for glow curve deconvolution. The whole system has been tested on standard glow curves using different models of the TL process (a single peak described by the Podgorsak approximation, first order kinetics and/or general order kinetics). Calculated values of basic TL parameters (E and s) show a good agreement with the results obtained by other authors. The main advantage of the system is in its modularity that enables flexible changes in the TL model and mathematical procedures of the glow curve analysis. (author)

Liquidus Projection and Isothermal Section of the Sb-Se-Sn System

Science.gov (United States)

Chang, Jui-shen; Chen, Sinn-wen

2017-12-01

Sb-Se-Sn ternary alloys are promising chalcogenide materials. The liquidus projection and 673.2 K (400 °C) isothermal section of the Sb-Se-Sn ternary system are determined. Numerous Sb-Se-Sn alloys are prepared, and their primary solidification phases are examined. In addition to the three terminal phases, (Sb), (Se) and (Sn), there are Sb2Sn3, SbSn, SnSe, SnSe2, Sb2Se3, Sn2Sb9Se9, and SnSb2Se4 phases. In addition, there are two miscibility gaps along the Sb-Se and Se-Sn and sides. There are ten invariant reactions in the Sb-Se-Sn ternary system, and seven of them are experimentally determined in this study. The lowest reaction temperature of determined invariant reaction is L + SbSn = (Sn) + SnSe at 515.4 K ± 5 K (242.2 °C ± 5 °C). There are nine tie-triangles, which are Liquid + SbSn + SnSe, SbSn + SnSe + (Sb), SnSe + (Sb) + Sn2Sb9Se9, (Sb) + Sb2Se3 + Sn2Sb9Se9, SnSe + Sn2Sb9Se9 + SnSb2Se4, Sb2Se3 + Sn2Sb9Se9 + SnSb2Se4, SnSe + SnSe2 + SnSb2Se4, SnSe2 + SnSb2Se4 + Sb2Se3, and SnSe2 + Sb2Se3 + Liquid in the 673.2 K (400 °C) isothermal section of the Sb-Se-Sn ternary system.

Electrical and thermal transport properties of Y bxCo4Sb12 filled skutterudites with ultrahigh carrier concentrations

Directory of Open Access Journals (Sweden)

Yulong Li

2015-11-01

Full Text Available For filled skutterudites, element Yb is one of the most common and important fillers. However, the optimal carrier concentration range in Y bxCo4Sb12 filled skutterudites has not been determined as a result of the low Yb filling fraction limit. In this study, a non-equilibrium fabrication process (MS-SPS process, consisting of a melt-spinning method and a spark plasma sintering technique, has been applied to prepare Y bxCo4Sb12 samples. The Yb filling fraction is successfully extended to 0.35, which provides the possibility to clarify the optimal carrier concentration range for Yb-filled skutterudites. High carrier concentrations, with a maximum of around 1 × 1021 cm−3, were achieved in the MS-SPS Y bxCo4Sb12 samples due to the significantly enhanced Yb filling fractions. The phase compositions, lattice parameters, electrical and thermal transport properties of the MS-SPS Y bxCo4Sb12 samples with high carrier concentrations were systematically investigated. An optimal carrier concentration range of around 5 ∼ 6 × 1020 cm−3, corresponding to the actual Yb filling fraction of around 0.21∼0.26, has been determined, which displays the highest thermoelectric performance in Y bxCo4Sb12 thermoelectric materials.

Influence of deep traps in the Tl response of ZrO{sub 2} + PTFE; Influencia de las trampas profundas en la respuesta Tl de ZrO{sub 2} + PTFE

Energy Technology Data Exchange (ETDEWEB)

Rivera M, T.; Azorin N, J.; Falcony G, C.; Martinez S, E.; Garcia H, M. [Universidad Autonoma Metropolitana-Iztapalapa, 09340 Mexico D.F. (Mexico)

2000-07-01

In this work are presented the results from investigating the processes related with the defects produced by ionizing radiation in ZrO{sub 2}. It is established an hypothesis which pretends to explain the phenomena that implicates the manifestation of Tl peaks in the brightness curve due to electron removal from the surface traps to the deep traps, through the thermo-transference process, where the excitonic process correspond to the F centers. During the experimental process it was observed this effect through the peaks running in Tl curve. These peaks are presented at 220 and 360 Centigrade for the material without any previous thermal treatment; while that in the samples thermally treated at 100 Centigrade during 1 minute it is observed a slipping in the first peak from 220 to 280 Centigrade, while the second stays in 360 Centigrade. (Author)

Synthesis and study of electrical properties of nonsuperconducting and low-Tc phases of Tl-Ba-Ca-Cu-O (TBCCO) superconducting materials

International Nuclear Information System (INIS)

Ahmed, F.; Samadder, A.M; Sultana, H.R.; Abul Hossain, M.; Khan, A.H.

2005-09-01

Samples of Tl-Ba-Ca-Cu-O system having nominal compositions of Tl 2 Ba 2 Ca 2n Cu 3+n O y (n=1, 2) have been synthesized. Sintering under different conditions were carried out to study their effect on the formation of superconductivity. In the present study it is found that all the samples prepared at temperature >850 deg. C show the dominance of nonsuperconducting phases. One sample prepared at well below the conventional sintering temperatures (655 deg. C) shows the formation of the low-T c phase of TBCCO system with T c =80K. In two samples simultaneous presence of two values of a∼b∼ namely 5.45A and 3.84A has been identified. (author)

Detection of irradiated foods by the thermoluminescence. Relationships between the temperature ranges of integrating TL glow curves and TL glow ratios

International Nuclear Information System (INIS)

Sekiguchi, Masayuki; Yamazaki, Masao; Goto, Michiko; Todoriki, Setsuko; Hagiwara, Shoji

2007-01-01

Our study demonstrated that the effects of the several temperature ranges for integrating TL glow intensity on the TL glow ratios by using spice-set purchased at a Turkish air port. The spice set had no labeling of irradiation feeds, but nine of 12 spices were judged as irradiated food in this study. Those temperature ranges were defined by evaluating the glow curves of irradiated TLD-100 chip (167-230degC), TLD-100 disc (177-238degC) and Dolomite element (145-258degC). Those are relatively stable and the difference of typical glow peak temperatures of TLD-100 disc in two institutes was less than 2%. On the other hand, those of TLD-100 tip was shift to higher temperature side at about 4degC because of declining of thermal conductance. The temperature ranges defined by TLD-100 were showed that discriminate more clearly between irradiated and nonirradiated spices compared with the full temperature range of TL measurement (70-400degC). With the exception of low glow intensity, background measurement for estimating net glow intensity was not necessary because TL glow ratio was hardly influenced whether the background measured or not. (author)

Mechanism of Pb and Sb role on the 2223 phase of BSCCO system superconductor

Energy Technology Data Exchange (ETDEWEB)

Sukirman, E; Sulisworo, P; Prasuad, W; Wuryanto, [Material Science Research Centre, National Atomic Energy Agency, Kawasan Puspiptek Serpong Tangerang (Indonesia)

1998-10-01

The mechanism of Pb and Sb role on the 2223 phase of Bi-Sr-Ca-Cu-O (BSCCO) system superconductor has been investigated. The 2223 phase samples without doping and with doping: Pb, and Sb have been synthesized by solid state reaction method. The samples characterization have been carried out through a susceptibility-, resistivity-, neutron diffraction profile-, and microstructure measurements. Crystal structure of the samples have been analyzed using RIETAN software. The analysis results show that relative content of the 2223 phase increase from 28% in the non-doped sample (TDP) to 75% in Pb-doped (DPB) and 44% in Sb-doped (DSB) samples. When, Pb, or Sb enter into the 2223 phase crystal system, then the oxygen atoms on SrO layers shift toward the copper atoms position on Cu(2)O{sub 2} layers as far as 0.1(1) and 0.1(1) A in DPB, and DSB, respectively. BiO layers shift away from SrO layers as far as 0.3(1) and 0.1(1) A in DPB, and DSB, respectively. The critical current density Jc increase from 3 A/cm{sup 2} in TDP to 210 and 35 A/cm{sup 2} in DPB, and DSB, respectively. The onset point of Tc also increase from 99 K in TDP to 103 and 107 K in DPB and DSB, respectively. It is concluded that the enhancement of the 2223 phase, Jc and onset point are due to improvement on the structure stability, improvement on the connection between unit-cells, and shortening the apical oxygen-Cu chains, respectively. (author)

Dosimetric characteristics of LKB:Cu,P solid TL detector

International Nuclear Information System (INIS)

Hashim, S.; Alajerami, Y.S.M.; Ghoshal, S.K.; Saleh, M.A.; Saripan, M.I.; Kadir, A.B.A.; Bradley, D.A.; Alzimami, K.

2014-01-01

The dosimetric characteristics of newly developed borate glass dosimeter modified with lithium and potassium carbonate (LKB) and co-doped with CuO and NH 4 H 2 PO 4 are reported. Broad peaks in the absence of any sharp peak confirms the amorphous nature of the prepared glass. A simple glow curve of Cu doped sample is observed with a single prominent peak (T m ) at 220 °C. The TL intensity response shows an enhancement of ∼100 times due to the addition of CuO (0.1 mol%) to LKB compound. A further enhancement of the intensity by a factor of 3 from the addition of 0.25 mol% NH 4 H 2 PO 4 as a co-dopant impurity is attributed to the creation of extra electron traps with consequent increase in energy transfer of radiation recombination centers. The TL yield performance of LKB:Cu,P with Z eff ≈8.92 is approximately seventeen times less sensitive compared to LiF:Mg,Ti (TLD-100). The proposed dosimeter shows good linearity up to 10 3 Gy, minimal fading and photon energy independence. These attractive features offered by our dosimeter is expected to pave the way towards dosimetric applications. - Highlights: • The NH 4 H 2 PO 4 impurities are cross linked with the CuO defect. • The addition of NH 4 H 2 PO 4 as a co-dopant improved the TL intensity by a factor of 3. • The proposed dosimeter shows good linearity up to 10 3 Gy. • Minimal fading and photon energy independence were observed

Determination of As, Se and Sb in different trades and blends of tobacco by neutron activation analysis

International Nuclear Information System (INIS)

Francisconi, Lucilaine S.; Damatto, Sandra R.; Silva, Paulo S.C. da

2011-01-01

The concentrations of As, Se and Sb were determined in two different cigarette trades (M and F). For each trade, four blends were selected for analysis: red, blue, silver and gold for M and red, blue, silver and fresh for F. The As, Se and Sb concentrations were determined by neutron activation analysis. For the analysis the samples were dried to eliminate moisture and the results were given in dry weight. Samples were irradiated together reference standards materials in the IEA-R1 IPEN reactor and counted in Ge-hiperpure detector. It was observed that As and Sb showed higher concentrations in M than in F and no significant differences were observed between the blends. (author)

Determination of As, Se and Sb in different trades and blends of tobacco by neutron activation analysis

Energy Technology Data Exchange (ETDEWEB)

Francisconi, Lucilaine S.; Damatto, Sandra R.; Silva, Paulo S.C. da, E-mail: pscsilva@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

The concentrations of As, Se and Sb were determined in two different cigarette trades (M and F). For each trade, four blends were selected for analysis: red, blue, silver and gold for M and red, blue, silver and fresh for F. The As, Se and Sb concentrations were determined by neutron activation analysis. For the analysis the samples were dried to eliminate moisture and the results were given in dry weight. Samples were irradiated together reference standards materials in the IEA-R1 IPEN reactor and counted in Ge-hiperpure detector. It was observed that As and Sb showed higher concentrations in M than in F and no significant differences were observed between the blends. (author)

Thermoelectric study of Ag doped SnSe-Sb2Se3 based alloy

Science.gov (United States)

Das, Anish; Talukdar, M.; Kumar, Aparabal; Sarkar, Kalyan Jyoti; Dhama, P.; Banerji, P.

2018-05-01

In this article we have synthesized p-type alloy of SnSe and Sb2Se3 (10 atomic %) to study the thermoelectric transport properties. The alloy was prepared by melt grown technique followed by spark plasma sintering and latter doped with 2 atomic % Ag to compensate the carrier density in order to achieve higher electrical conductivity (σ). Out of these, the doped sample resulted in the maximum figure of merit, ZT˜0.7 at 773 K due to the existence of the secondary phase AgSbSe2 and reduced lattice thermal conductivity (0.61 W m-1 K-1 at 300 K). The fitted lattice thermal conductivity shows that point defect and Umklapp scattering are the primary process of phonon scattering for all the samples whereas the fitted mobility data confirms acoustic phonon scattering along with point defect and grain boundary scattering to be the main carrier scattering mechanism. More over room temperature carrier density and electrical conductivity are found to increase for the doped sample which further corroborate (90%)SnSe-(10%)Sb2Se3:2%Ag to be a potential candidate for highly efficient thermoelectric materials.

Stability of detecting system using NaI(Tl)

International Nuclear Information System (INIS)

Zhuo Yunshang; Lei Zhangyun; Zen Yu; Gong Hua

1996-01-01

A detecting system using NaI(Tl) is widely used in research and industry of nuclear science and other fields. For providing the high accuracy and working well under inclement environment, the stability of detecting system using NaI(Tl) is very important. The variation of environment temperature, the change of counting rate and long time continuous working of detector will cause un-negligible effect on the measurement. Three approaches were used. They are: 1) temperature control (It makes the effect of the variation of environment temperature on the measurement negligible.); 2) spectrum stabilizing (It adjust the peak position of the spectrum when the counting rate changes.); and 3) auto-checking and adjusting (It adjusts the drift of the NaI(Tl) detecting system when it works continuously)

Heavy element affinities in Apollo 17 samples

International Nuclear Information System (INIS)

Allen, R.O. Jr.; Jovanovic, S.; Reed, G.W. Jr.

1975-01-01

204 Pb, Bi, Tl and Zn in samples from Apollo 17 exhibit relationships not found in samples from other sites. 204 Pb, Tl and Zn in residues remaining after dilute acid leaching are correlated with one another. Orange soil 74220, which is enriched in 204 Pb, Tl and Zn, is included in these relationships. In addition the submicron metallic phase generally associated with agglutinate formation is correlated with all three of these elements; this relationship has already been reported for 204 Pb in other samples. Thus, orange soil and agglutinates appear to be involved in concentrating heavy volatile metals. A process other than mixing is required to account for this. As a consequence of the isolation of the landing site by the surrounding massifs, local supply and recycling of volatile trace elements in soils may account for some of the interelement relations. (Auth.)

Thallium (III) determination in the Baltic seawater samples by ICP MS after preconcentration on SGX C18 modified with DDTC.

Science.gov (United States)

Krasnodębska-Ostręga, Beata; Sadowska, Monika; Piotrowska, Katarzyna; Wojda, Marta

2013-08-15

The main difficulty of speciation analysis of thallium lies in extremely low concentrations of Tl(III) in comparison to Tl(I), which is the dominating form of thallium in environmental samples. In this study, a sensitive method is presented for separation of trace amounts of Tl(III) from Tl(I) and preconcentration of Tl(III) using octadecyl silica gel modified with diethyldithiocarbamate (DDTC). Under optimal conditions, only Tl(III) is retained on the sorbent, and then eluted with 96% ethanol. After chemical decomposition of Tl(III)-DDTC complex, thallium is determined by inductively coupled plasma mass spectrometry. High performance liquid chromatography with ICP MS detection was used to control the correctness of the obtained results. Parameters affecting solid phase extraction (SPE) such as pH, type, concentration and volume of eluent, breakthrough volume, and the impact of sample salinity (chlorides) and other interfering ions (Cd(II), Zn(II), Pb(II), Cu(II), Sn(II)) were investigated. The limit of detection (LOD), evaluated for 2 mL of sample solution, was 0.10 ng for Tl(I) and 0.43 ng for Tl(III). The method was applied to the determination of Tl(I) and Tl(III) in the Baltic seawater samples enriched in both thallium species. Copyright © 2013 Elsevier B.V. All rights reserved.

Reduction in thermal conductivity of BiSbTe lump

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Kaleem [King Saud University, Sustainable Energy Technologies Center, College of Engineering, PO Box 800, Riyadh (Saudi Arabia); Wan, C. [Tsinghua University, State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Beijing (China); Al-Eshaikh, M.A.; Kadachi, A.N. [King Saud University, Research Center, College of Engineering, PO Box 800, Riyadh (Saudi Arabia)

2017-03-15

In this work, systematic investigations on the thermal conductivities of BiSbTe lump, microstructured pristine BiSbTe bulk and single wall carbon nanotubes (SWCNTs)/BiSbTe bulk nanocomposites were performed. BiSbTe lumps were crushed to form a coarse powder (200 μm) and effect of particle size reduction on the effective thermal conductivity of BiSbTe (200 μm) bulk were analyzed. For further reduction in the conductivity, a two pronged strategy has been employed. First, additional refinement of BiSbTe (200 μm) were performed through ball milling in an inert environment. Second, SWCNTs in 0.75, and 1.0 vol% were distributed uniformly in the fine BiSbTe ball milled powder. The results showed that the effective thermal conductivities decrease with the reduction in the particle size from lump to BiSbTe (200 μm) bulk as well as with the addition of SWCNTs accompanied by further refinement of BiSbTe particles. The significant reduction in thermal conductivities of the lump was achieved for pure BiSbTe (200 μm) bulk and 0.75 vol% of SWCNTs/BiSbTe composite. This can be ascribed to the enhanced phonon scattering by the grain boundaries between the nanostructured BiSbTe particles as well as the interfaces between BiSbTe and the low dimensional carbon nanotubes. (orig.)

Persistent luminescence, TL and OSL characterization of beta irradiated SrAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} combustion synthesized phosphor

Energy Technology Data Exchange (ETDEWEB)

Zúñiga-Rivera, N.J. [Departamento de Física, Posgrado en Nanotecnología, Universidad de Sonora, Hermosillo, Sonora 83000 (Mexico); García, R.; Rodríguez-Mijangos, R.; Chernov, V.; Meléndrez, R.; Pedroza-Montero, M. [Departamento de Investigación en Física, Universidad de Sonora, Hermosillo, Sonora 83000 (Mexico); Barboza-Flores, M., E-mail: mbarboza@cifus.uson.mx [Departamento de Investigación en Física, Universidad de Sonora, Hermosillo, Sonora 83000 (Mexico)

2014-05-01

The persistent luminescence (PLUM), thermoluminescence (TL) and optically stimulated luminescence (OSL) properties of strontium aluminates co-doped with Eu{sup +2} and Dy{sup +3} exposed to beta radiation is reported. The phosphor was synthesized by the combustion synthesis method employing a highly exothermic redox reaction between the metal nitrates [Al(NO{sub 3}){sub 3}, Sr(NO{sub 3}){sub 2}, Eu(NO{sub 3}){sub 3} and Dy(NO{sub 3}){sub 3}] and organic fuel carbohydrazide (CH{sub 6}N{sub 4}O). The long decay PLUM emission, TL and OSL were measured as a function of beta radiation dose. A wide emission band centered at 510 nm (green) related to Eu{sup 2+} ions and lattice defects were observed for the synthesized samples. The presence of a variety of defects and aggregates were responsible for the observed broad 100 °C peaked TL glow curve of the irradiated sample which is composed of several overlapped TL peaks. The existence of multiple trapping levels, with different trapping/detrapping probabilities, is behind the particular features for the PLUM, TL and OSL emissions. We conclude that in the SrAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} phosphors, the low temperature TL peaked around 30–75 °C is responsible for the PLUM emission and those around 100 °C were related to very stable trapping states which provide suitable radiation storage properties to be used as a PLUM/TL/OSL radiation phosphor.

Structural and electronic properties of thallium compounds

International Nuclear Information System (INIS)

Paliwal, Neetu; Srivastava, Vipul

2016-01-01

The tight binding linear muffin-tin-orbital (TB-LMTO) method within the local density approximation (LDA has been used to calculate structural and electronic properties of thallium pnictides TlX (X=Sb, Bi) at high pressure. As a function of volume, the total energy is evaluated. Apart from this, the lattice parameter (a_0), bulk modulus (B_0), band structure (BS) and density of states (DOS) are calculated. From energy band diagram we observed metallic behaviour in TlSb and TlBi compounds. The values of equilibrium lattice constants and bulk modulus are agreed well with the available data.

Structural and electronic properties of thallium compounds

Energy Technology Data Exchange (ETDEWEB)

Paliwal, Neetu, E-mail: neetumanish@gmail.com [Department of Physics, AISECT University Bhopal, 464993 (India); Srivastava, Vipul [Department of Engineering Physics, NRI Institute of Research & Technology, Raisen Road, Bhopal, 462021 (India)

2016-05-06

The tight binding linear muffin-tin-orbital (TB-LMTO) method within the local density approximation (LDA has been used to calculate structural and electronic properties of thallium pnictides TlX (X=Sb, Bi) at high pressure. As a function of volume, the total energy is evaluated. Apart from this, the lattice parameter (a{sub 0}), bulk modulus (B{sub 0}), band structure (BS) and density of states (DOS) are calculated. From energy band diagram we observed metallic behaviour in TlSb and TlBi compounds. The values of equilibrium lattice constants and bulk modulus are agreed well with the available data.

Exploring the thermoelectric and magnetic properties of uranium selenides: Tl{sub 2}Ag{sub 2}USe{sub 4} and Tl{sub 3}Cu{sub 4}USe{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Azam, Sikander; Khan, Saleem Ayaz [New Technologies – Research Center, University of West Bohemia, Univerzitni 8, 30614 Pilsen (Czech Republic); Din, Haleem Ud [Department of Physics, Hazara University, Mansehra (Pakistan); Khenata, Rabah [Laboratoire de Physique Quantique et de Modélisation Mathématique (LPQ3M), Département de Technologie, Université de Mascara, Mascara 29000 (Algeria); Goumri-Said, Souraya, E-mail: sosaid@alfaisal.edu [College of Science, Physics department, Alfaisal University, P.O. Box 50927, Riyadh 11533 (Saudi Arabia)

2016-09-01

The electronic, magnetic and thermoelectric properties of Tl{sub 2}Ag{sub 2}USe{sub 4} and Tl{sub 3}Cu{sub 4}USe{sub 6} compounds were investigated using the full potential linear augmented plane wave (FP-LAPW) method based on the density functional theory (DFT). The exchange correlation was treated with the generalized gradient approximation plus optimized effective Hubbard parameter and spin–orbit coupling (GGA+U+SOC). The present uranium selenides show narrow direct energy band gap values of 0.7 and 0.875 eV for Tl{sub 2}Ag{sub 2}USe{sub 4} and Tl{sub 3}Cu{sub 4}USe{sub 6} respectively. For both selenides U-d/f states are responsible for electrical transport properties. Uranium atoms were the most contributors in the magnetic moment compared to other atoms and show ferromagnetic nature. The spin density isosurfaces show the polarization of neighboring atoms of Uranium, such as silver/copper and selenium. Thermoelectric calculations reveal that Tl{sub 3}Cu{sub 4}USe{sub 6} is more suitable for thermoelectric device applications than Tl{sub 2}Ag{sub 2}USe{sub 4}. - Highlights: • Electronic, magnetic and thermoelectric properties of uranium selenides are investigated with DFT. • They show a narrow direct energy band gap of 0.7 and 0.875 eV. • U-d/f states are responsible for electrical transport properties. • Tl{sub 3}Cu{sub 4}USe{sub 6} is more suitable for thermoelectric device applications than Tl{sub 2}Ag{sub 2}USe{sub 4}.

Zeta potential study of Sb2S3 nanoparticles synthesized by a facile polyol method in various surfactants

Science.gov (United States)

Saxena, Monika; Okram, Gunadhor Singh

2018-05-01

In the present work, we report the successful synthesis of stibnite Sb2S3 nanoparticles (NPs) by a facile polyol method using various surfactant. The structural and optical properties were investigated by X-ray diffraction (XRD), Raman spectroscopy and Zeta potential. Rietveld refinement of XRD data confirms the single phase orthorhombic crystal structure of stibnite Sb2S3. Presence of six obvious Raman modes further confirmed their stoichiometric formation. Effect of different surfactants on the surface charge of Sb2S3 NPs was studied using Zeta potential measurement in deionized water at different pH values. They reveal that these NPs are more stable when it was synthesized in presence of EDTA than that of CTAB or without surfactant samples with high zeta potential. The isoelectronic point was found at pH = 6.4 for pure sample, 3.5 and 7.2 for CTAB and not found for EDTA Sb2S3 samples. This information can be useful for many industrial applications like pharmaceuticals, ceramics, waste water treatment and medicines.

TL glow curve analysis of UV, beta and gamma induced limestone collected from Amarnath holy cave

Directory of Open Access Journals (Sweden)

Vikas Dubey

2015-01-01

Full Text Available The paper reports themoluminescence glow curve analysis of UV (ultraviolet, β (beta and γ (gamma induced limestone collected from Amarnath holy cave. The collected natural sample was characterized by X-ray diffraction (XRD technique and crystallite size calculated by Scherer's formula. Surface morphology and particle size was calculated by transmission electron microscopy (TEM study. Effect of annealing temperature on collected lime stone examined by TL glow curve study. The limestone was irradiated by UV radiation (254 nm source and the TL glow curve recorded for different UV exposure time. For beta irradiation Sr90 source was used and is shows intense peak at 256 °C with a shoulder peak at higher temperature range. For gamma radiation Co60 source and TL glow curve recorded for different doses of gamma. The kinetic parameters calculation was performed for different glow curve by computerized glow curve deconvolution (CGCD technique. The chemical composition of natural limestone was analyzed by energy dispersive X-ray spectroscopy (EDXS.

Crystal structure, chemical bond and enhanced performance of β-Zn4Sb3 compounds with interstitial indium dopant

International Nuclear Information System (INIS)

Tang, Dingguo; Zhao, Wenyu; Yu, Jian; Wei, Ping; Zhou, Hongyu; Zhu, Wanting; Zhang, Qingjie

2014-01-01

Highlights: • The interstitial In dopant leads to the local structural perturbations in β-Zn 4 Sb 3 . • The simultaneous increases in α and σ are observed in the In-doped Zn 4 Sb 3 compounds. • The In dopant plays different doping behaviors by the dopant contents in the samples. • A maximum ZT of 1.41 at 700 K is achieved for the In-doped Zn 4 Sb 3 compounds. - Abstract: In-doped β-Zn 4 Sb 3 compounds (Zn 4−x In x Sb 3 , 0 ⩽ x ⩽ 0.24) were prepared by melt-quenching and spark plasma sintering technology in the work. The resultant samples were systematically investigated by X-ray diffraction, X-ray photoelectron spectroscopy, differential scanning calorimetry and thermoelectric property measurements. The In dopant was identified to preferentially occupy the interstitial site in β-Zn 4 Sb 3 and led to the local structural perturbations near the 12c Sb2 and 36f Zn1 sites. The Auger parameters of Zn and Sb indicated that the increase in the valence of Zn was attributed to the charge transfer from Zn to In atoms. The binding energies of In 3d 5/2 core level showed that the interstitial In dopant was n-type dopant (In 3+ ) in slightly In-doped Zn 4−x In x Sb 3 , but acted as acceptor and was p-type dopant (In + ) in heavily In-doped ones. The discovery provides a reasonable explanation for the puzzled relation between σ and x for Zn 4−x In x Sb 3 . Simultaneously increasing the electrical conductivity and Seebeck coefficient of Zn 4−x In x Sb 3 can be realized through the local structural perturbations. The significantly enhanced power factor and the intrinsic low thermal conductivity resulted in a remarkable increase in the dimensionless figure of merit (ZT). The highest ZT reached 1.41 at 700 K for Zn 3.82 In 0.18 Sb 3 and increased by 68% compared with that of the undoped β-Zn 4 Sb 3

Measurement of the infarcted area by 201Tl myocardial emission CT

International Nuclear Information System (INIS)

Tamaki, Shunichi; Murakami, Tomoyuki; Kambara, Hirofumi

1982-01-01

201 Tl-ECT was performed in 28 cases 4 weeks after the onset of acute myocardial infarction to calculate the volume of infarction for comparison with the CK-MB infarction size obtained in the acute phase. The infarct area obtained by two-dimensional 201 Tl scintigraphy in 18 cases treated by the conventional method showed a positive correlation with the CK-MB infarct size, but the volume of infarction by 201 Tl-ECT produced a better correlation. In the group with successful thrombolysis, the serum CK-MB level reached a peak soon after the onset, accompanied by release of more CK-MB for a constant volume of infarction obtained by 201 Tl-ECT, as compared with the group with unsuccessful thrombolysis or conventional therapy. This suggests the involvement of washout phenomenon by reperfusion. Although there are some limitations, the three-dimensional detection of the distribution of myocardial blood flow by 201 Tl-ECT is useful, covering disadvantages of two-dimensional images. (Chiba, N.)

Thermoelectric properties of high pressure synthesized lithium and calcium double-filled CoSb3

Directory of Open Access Journals (Sweden)

Xiaohui Li

2017-01-01

Full Text Available Lithium and calcium are inefficient filling elements of CoSb3 at ambient pressure, but show nice filling behavior under high pressure. In this work, we synthesized Li/Ca double-filled CoSb3 with high pressure synthesis method. The products show the skutterudite structure of Im3¯ symmetry. Thermoelectric properties were effectively enhanced through Li and Ca co-filling. For the optimal Li0.08Ca0.18Co4Sb12 sample, the power factor maintains a relatively high value over the whole measurement temperature range and peaks at 4700μWm−1K−2, meanwhile the lattice thermal conductivity is greatly suppressed, leading to a maximal ZT of 1.18 at 700 K. Current work demonstrates high pressure synthesis as an effective method to produce multiple elemental filled CoSb3 skutterudites.

Regional analysis of annual maximum rainfall using TL-moments method

Science.gov (United States)

Shabri, Ani Bin; Daud, Zalina Mohd; Ariff, Noratiqah Mohd

2011-06-01

Information related to distributions of rainfall amounts are of great importance for designs of water-related structures. One of the concerns of hydrologists and engineers is the probability distribution for modeling of regional data. In this study, a novel approach to regional frequency analysis using L-moments is revisited. Subsequently, an alternative regional frequency analysis using the TL-moments method is employed. The results from both methods were then compared. The analysis was based on daily annual maximum rainfall data from 40 stations in Selangor Malaysia. TL-moments for the generalized extreme value (GEV) and generalized logistic (GLO) distributions were derived and used to develop the regional frequency analysis procedure. TL-moment ratio diagram and Z-test were employed in determining the best-fit distribution. Comparison between the two approaches showed that the L-moments and TL-moments produced equivalent results. GLO and GEV distributions were identified as the most suitable distributions for representing the statistical properties of extreme rainfall in Selangor. Monte Carlo simulation was used for performance evaluation, and it showed that the method of TL-moments was more efficient for lower quantile estimation compared with the L-moments.

Dipyridamole 201Tl scintigraphy in the evaluation of prognosis after myocardial infarction

International Nuclear Information System (INIS)

Okada, R.D.; Glover, D.K.; Leppo, J.A.

1991-01-01

Dipyridamole 201Tl imaging has been proposed as an alternative to exercise ECG testing for the prehospital discharge evaluation of patients recovering from myocardial infarction. The rationale is that many postinfarction patients with exercise-induced ischemia experience later cardiac events, and the sensitivity of predischarge exercise ECG testing in patients with multivessel disease ranges from only 45% to 62%. In addition, several groups of investigators have shown the sensitivity of submaximum exercise 201Tl imaging to be less than ideal. This report summarizes the current status of dipyridamole 201Tl imaging in the period of 1-13 days after myocardial infarction. Although the number of studies performed to date is limited, the following conclusions can be drawn: dipyridamole 201Tl imaging after myocardial infarction was associated with no serious side effects, and those present could be quickly reversed with aminophylline; redistribution with dipyridamole 201Tl images definitely correlates with prognosis after uncomplicated myocardial infarction; dipyridamole 201Tl imaging is definitely useful in patients unable to exercise for a variety of reasons; and future studies are definitely indicated to further define the role of dipyridamole 201Tl imaging for assessing prognosis, especially in those patients undergoing interventional therapy after acute myocardial infarction

Oral administration of the 5-HT6 receptor antagonists SB-357134 and SB-399885 improves memory formation in an autoshaping learning task.

Science.gov (United States)

Perez-García, Georgina; Meneses, Alfredo

2005-07-01

In this work we aimed to re-examine the 5-HT6 receptor role, by testing the selective antagonists SB-357134 (1-30 mg/kg p.o.) and SB-399885 (1-30 mg/kg p.o.) during memory consolidation of conditioned responses (CR%), in an autoshaping Pavlovian/instrumental learning task. Bioavailability, half-life and minimum effective dose to induce inappetence for SB-357134 were 65%, 3.4 h, and 30 mg/kg p.o., and for SB-399885 were 52%, 2.2 h, and 50 mg/kg p.o., respectively. Oral acute and chronic administration of either SB-357134 or SB-399885 improved memory consolidation compared to control groups. Acute administration of SB-357134, at 1, 3, 10 and 30 mg/kg, produced a CR% inverted-U curve, eliciting the latter dose a 7-fold increase relative to saline group. Acute injection of SB-399885 produced significant CR% increments, being 1 mg/kg the most effective dose. Repeated administration (7 days) of either SB-357134 (10 mg/kg) or SB-399885 (1 mg/kg) elicited the most significant CR% increments. Moreover, modeling the potential therapeutic benefits of 5-HT6 receptor blockade, acute or repeated administration of SB-399885, at 10 mg/kg reversed memory deficits produced by scopolamine or dizocilpine, and SB-357134 (3 and 10 mg/kg) prevented amnesia and even improved performance. These data support the notion that endogenously 5-HT acting, via 5-HT6 receptor, improves memory consolidation.

Degradation of myocardial perfusion SPECT images caused by contaminants in thallous (201Tl) chloride

International Nuclear Information System (INIS)

Staelens, Steven G.; Wit, Tim C. de; Lemahieu, Ignace A.; Beekman, Freek J.

2008-01-01

Thallous ( 201 Tl) chloride is a single-photon emission computed tomography (SPECT) tracer mainly used for assessing perfusion and viability of myocardial tissue. 201 Tl emits X-rays around 72 keV and gammas at 167 keV, and has a half-life of 73 h. Regulations allow an intrinsic contamination up to 3-5%, which is mainly caused by 200 Tl (368 keV; 26 h) and by 202 Tl (439 keV; 12.2 days). Contra-intuitive to the low-level percentages in which these contaminants are present, their impact may be significant because of much higher gamma camera sensitivity for these high-energy photon emissions. Therefore, we investigate the effects of the contaminants in terms of detected fractions of photons in projections and contrast degradation in reconstructed images. Acquisitions of a digital thorax phantom filled with thallous ( 201 Tl) chloride were simulated with a validated Monte Carlo tool, thereby, modelling 1% of contamination by 200 Tl and 202 Tl each. In addition, measurements of a thorax phantom on a dual-headed gamma camera were performed. The product used was contaminated by 0.17% of 200 Tl and 0.24% of 202 Tl at activity reference time (ART). This ART is specified by the manufacturer, thereby, accounting for the difference in half-lives of 201 Tl and its contaminants. These measurements were repeated at different dates associated with various contamination levels. Simulations showed that, with 1% of 200 Tl and 202 Tl, the total contamination in the 72 keV window can rise up to one out of three detected photons. For the 167keV window, the contamination is even more pronounced: more than four out of five detections in this photopeak window originate from contaminants. Measurements indicate that cold lesion contrast in myocardial perfusion SPECT imaging is at maximum close to ART. In addition to a higher noise level, relative contrast decreases 15% 2 days early to ART, which is explained by an increase in 200 Tl contamination. After ART, contrast decreased by 16% when

AlGaAsSb Vapor Phase Epitaxy and Laser Program.

Science.gov (United States)

1983-06-01

graded or step-graded ternary film structures to fulfill the role of a sub- strate. One of the objectives of the program, however, was to determine the...0.02 ur/mmn. 27 MRDC81-14083 Fig. 11 RED pattern of the ( iaSb sample of Fig. 6. 28 7- 7 crystal. No samples from this group were submitted to SEM

CRYSTAL-QUASICHEMICAL ANALYSIS OF DEFECT SUBSYSTEM OF DOPED PbTe: Sb CRYSTALS AND Pb-Sb-Te SOLID SOLUTIONS

Directory of Open Access Journals (Sweden)

D.M. Freik

2014-05-01

Full Text Available Within crystalquasichemical formalism models of point defects of crystals in the Pb-Sb-Te system were specified. Based on proposed crystalquasichemical formulae of antimony doped crystals PbTe:Sb amphoteric dopant effect was explained. Mechanisms of solid solution formation for РbТе-Sb2Те3: replacement of antimony ions lead sites  with the formation of cation vacancies  (I or neutral interstitial tellurium atoms  (II were examined. Dominant point defects in doped crystals PbTe:Sb and РbТе-Sb2Те3 solid solutions based on p-PbTe were defined. Dependences of concentration of dominant point defects, current carriers and Hall concentration on content of dopant compound and the initial deviation from stoichiometry in the basic matrix were calculated.

Tl response of KMgF3: Lu + PTFE at ultraviolet radiation

International Nuclear Information System (INIS)

Gonzalez, P.R.; Alarcon, N.G.; Furetta, C.; Azorin, J.

2003-01-01

Ionizing radiation has different types of interaction with a crystalline solid. However, only few effects are interesting to optimize some thermoluminescent (Tl) properties of certain Tl materials. This paper presents results obtained by irradiating KMgF 3 : Lu + Ptfe Tl dosimeters with ultraviolet (UV) radiation previously exposed to gamma radiation. These results showed that those dosimeters not exposed previously to gamma radiation did not presented any Tl signal. Meanwhile, those previously submitted to gamma irradiation showed that their sensitivity was increased as the gamma dose increased. The glow curve of sensitized KMgF 3 : Lu + Ptfe exposed to UV radiation, presented the dosimetric pea at 212 C. This makes this material to be promissory for measuring UV radiation. (Author)

Photoconductivity in the chalcohalide semiconductor, SbSeI: a new candidate for hard radiation detection.

Science.gov (United States)

Wibowo, Arief C; Malliakas, Christos D; Liu, Zhifu; Peters, John A; Sebastian, Maria; Chung, Duck Young; Wessels, Bruce W; Kanatzidis, Mercouri G

2013-06-17

We investigated an antimony chalcohalide compound, SbSeI, as a potential semiconductor material for X-ray and γ-ray detection. SbSeI has a wide band gap of 1.70 eV with a density of 5.80 g/cm(3), and it crystallizes in the orthorhombic Pnma space group with a one-dimensional chain structure comprised of infinite zigzag chains of dimers [Sb2Se4I8]n running along the crystallographic b axis. In this study, we investigate conditions for vertical Bridgman crystal growth using combinations of the peak temperature and temperature gradients as well as translation rate set in a three-zone furnace. SbSeI samples grown at 495 °C peak temperature and 19 °C/cm temperature gradient with 2.5 mm/h translation rate produced a single phase of columnar needlelike crystals aligned along the translational direction of the growth. The ingot sample exhibited an n-type semiconductor with resistivity of ∼10(8) Ω·cm. Photoconductivity measurements on these specimens allowed us to determine mobility-lifetime (μτ) products for electron and hole carriers that were found to be of similar order of magnitude (∼10(-4) cm(2)/V). Further, the SbSeI ingot with well-aligned, one-dimensional columnar needlelike crystals shows an appreciable response of Ag Kα X-ray.

Investigation of the gamma radiation from the inelastic scattering of 2.75 MeV on 203Tl and 205Tl

International Nuclear Information System (INIS)

Hegewisch, S.

1976-01-01

The experimental presupositions for the measurements of (n,n'γ) reactions with time of flight discrimination have been established. By an investigation of the isotopes 203 Tl and 205 Tl with this method 120 gamma-transitions could be determined. The exact evaluation of their energies and intensities led to a completion of the level diagrams. The enrgies could be determined with a precision nearly one order of magnitude higher than the values existing hither to. (orig./WL) [de

Clinical application of 201Tl scintigraphy in patients with cold thyroid nodules

International Nuclear Information System (INIS)

Tonami, N.; Bunko, H.; Michigishi, T.; Kuwajima, A.; Hisada, K.

1978-01-01

201 Tl-chloride scintigraphy was performed in 45 patients with cold thyroid nodules. The 201 Tl scintigram was positive in 17 of 18 thyroid patients with cancer (94.4%), 8 of 20 patients with an adenoma (40.0%), 1 of 2 adenomatous goiter patients (50.5%), and all of 5 cases of chronic thyroiditis (100.0%). When the cold nodule was demonstrated to be positive with 201 Tl, the statistical chance of the lesion being a cellular one was 100.0% and a risk of its malignancy was 54.8%. On the other hand, the nodule with negative 201 Tl concentration had a 14.3% chance of cellularity and a 7.1% risk of malignancy. Thus, 201 Tl scintigraphy is of use in the differential diagnosis of the cold thyroid nodule

Comparison of functional parameters of CsI:Tl crystals and thick films

International Nuclear Information System (INIS)

Fedorov, A.; Gektin, A.; Lebedynskiy, A.; Mateychenko, P.; Shkoropatenko, A.

2013-01-01

500 mkm thick CsI:Tl columnar films can be produced using thermal evaporation in vacuum by sublimation of the same bulk crystal. Comparison of afterglow and radiation stability of deposited CsI:Tl films with source crystal was the aim of current work. It is shown that the afterglow in the films is always below its level in initial single crystal. It was ascertained that the annealing atmospheres influence the processes leading to the activator depletion of the films during the thermal processing. -- Highlights: ► Thick CsI:Tl columnar films were obtained by thermal evaporation in vacuum. ► Radiation stability of such CsI:Tl films appears to be better than that of crystal. ► CsI:Tl film parameters can be modified by annealing in different atmospheres

Simultaneous removal of Cd(II) and Sb(V) by Fe–Mn binary oxide: Positive effects of Cd(II) on Sb(V) adsorption

Energy Technology Data Exchange (ETDEWEB)

Liu, Ruiping [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); Liu, Feng [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Hu, Chengzhi, E-mail: czhu@rcees.ac.cn [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); He, Zan [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Liu, Huijuan; Qu, Jiuhui [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

2015-12-30

Highlights: • Fe–Mn binary oxide achieves the simultaneous removal of Cd(II) and Sb(V). • Cd(II) at above 0.25 mmol/L improves Sb(V) adsorption onto FMBO. • Cd(II) improves more significant Sb(V) adsorption than Ca{sup 2+} and Mn{sup 2+}. • Sb(V) adsorption decreases whereas Cd(II) adsorption increases with elevated pH. • The increased ζ-potential and Cd(II)–Sb(V) precipitation favors Sb(V) adsorption. - Abstract: The coexistence of cadmium ion (Cd(II)) and antimonate (Sb(V)) creates the need for their simultaneous removal. This study aims to investigate the effects of positively-charged Cd(II) on the removal of negative Sb(V) ions by Fe–Mn binary oxide (FMBO) and associated mechanisms. The maximum Sb(V) adsorption density (Q{sub max,Sb(V)}) increased from 1.02 to 1.32 and 2.01 mmol/g in the presence of Cd(II) at 0.25 and 0.50 mmol/L. Cd{sup 2+} exhibited a more significant positive effect than both calcium ion (Ca{sup 2+}) and manganese ion (Mn{sup 2+}). Cd{sup 2+} showed higher affinity towards FMBO and increased its ζ-potential more significantly compared to Ca{sup 2+} and Mn{sup 2+}. The simultaneous adsorption of Sb(V) and Cd(II) onto FMBO can be achieved over a wide initial pH (pH{sub i}) range from 2 to 9, and Q{sub Sb(V)} decreases whereas Q{sub Cd(II)} increases with elevated pH{sub i}. Their combined values, as expressed by Q{sub Sb(V)+Cd(II)}, amount to about 2 mmol/g and vary slightly in the pH{sub i} range 4–9. FTIR and XPS spectra indicate the significant synergistic effect of Cd(II) on Sb(V) adsorption onto FMBO, and that little chemical valence transformation occurs. These results may be valuable for the treatment of wastewater with coexisting heavy metals such as Cd(II) and Sb(V).

Drastic effect of the Mn-substitution in the strongly correlated semiconductor FeSb2.

Science.gov (United States)

Kassem, Mohamed A.; Tabata, Yoshikazu; Waki, Takeshi; Nakamura, Hiroyuki

2017-06-01

We report the effects of Mn substitution, corresponding to hole doping, on the electronic properties of the narrow gap semiconductor, FeSb2, using single crystals of Fe1- x Mn x Sb2 grown by the Sb flux method. The orthorhombic Pnnm structure was confirmed by powder X-ray diffraction (XRD) for the pure and Mn-substituted samples. Their crystal structure parameters were refined using the Rietveld method. The chemical composition was investigated by wavelength-dispersive X-ray spectroscopy (WDX). The solubility limit of Mn in FeSb2 is x max ˜ 0.05 and the lattice constants change monotonically with increasing the actual Mn concentration. A drastic change from semiconducting to metallic electronic transports was found at very low Mn concentration at x ˜ 0.01. Our experimental results and analysis indicate that the substitution of a small amount of Mn changes drastically the electronic state in FeSb2 as well as the Co-substitution does: closing of the narrow gap and emergence of the density of states (DOS) at the Fermi level.

Sb(III)-Imprinted Organic-Inorganic Hybrid Sorbent Prepared by Hydrothermal-Assisted Surface Imprinting Technique for Selective Adsorption of Sb(III)