Physical properties of fault zone rocks from SAFOD: Tying logging data to high-pressure measurements on drill core

Science.gov (United States)

Jeppson, T.; Tobin, H. J.

2013-12-01

In the summer of 2005, Phase 2 of the San Andreas Fault Observatory at Depth (SAFOD) borehole was completed and logged with wireline tools including a dipole sonic tool to measure P- and S-wave velocities. A zone of anomalously low velocity was detected from 3150 to 3414 m measured depth (MD), corresponding with the subsurface location of the San Andreas Fault Zone (SAFZ). This low velocity zone is 5-30% slower than the surrounding host rock. Within this broad low-velocity zone, several slip surfaces were identified as well as two actively deforming shear zones: the southwest deformation zone (SDZ) and the central deformation zone (CDZ), located at 3192 and 3302 m MD, respectively. The SAFZ had also previously been identified as a low velocity zone in seismic velocity inversion models. The anomalously low velocity was hypothesized to result from either (a) brittle deformation in the damage zone of the fault, (b) high fluid pressures with in the fault zone, or (c) lithological variation, or a combination of the above. We measured P- and S-wave velocities at ultrasonic frequencies on saturated 2.5 cm diameter core plug samples taken from SAFOD core obtained in 2007 from within the low velocity zone. The resulting values fall into two distinct groups: foliated fault gouge and non-gouge. Samples of the foliated fault gouge have P-wave velocities between 2.3-3.5 km/s while non-gouge samples lie between 4.1-5.4 km/s over a range of effective pressures from 5-70 MPa. There is a good correlation between the log measurements and laboratory values of P-and S wave velocity at in situ pressure conditions especially for the foliated fault gouge. For non-gouge samples the laboratory values are approximately 0.08-0.73 km/s faster than the log values. This difference places the non-gouge velocities within the Great Valley siltstone velocity range, as measured by logs and ultrasonic measurements performed on outcrop samples. As a high fluid pressure zone was not encountered during

Permeability log using new lifetime measurements

International Nuclear Information System (INIS)

Dowling, D.J.; Boyd, J.F.; Fuchs, J.A.

1975-01-01

Comparative measurements of thermal neutron decay time are obtained for a formation after irradiation with a pulsed neutron source. Chloride ions in formation fluids are concentrated by the electrosmosis effect using charged poles on a well logging sonde. The formation is irradiated with fast neutrons and a first comparative measure of the thermal neutron decay time or neutron lifetime is taken. The chloride ions are then dispersed by acoustic pumping with a magnetostrictive transducer. The formation is then again irradiated with fast neutrons and a comparative measure of neutron lifetime is taken. The comparison is a function of the variation in chloride concentration between the two measurements which is related to formation permeability

A comparison between elemental logs and core data

International Nuclear Information System (INIS)

Kerr, S.A.; Grau, J.A.; Schweitzer, J.S.

1992-01-01

Neutron-induced gamma-ray spectroscopy, of prompt capture and delayed activation, together with natural gamma-ray measurements, provides a borehole elemental analysis to characterize rock matrix composition. This study involved extensive core and log data in two wells. One well was drilled with a barite-weighted oil-based mud through a shallow marine sand. The other was drilled with fresh water-based mud through a channel sand, mudstone sequence overlying limestone. The results illustrate the importance of a suitable core sampling strategy and the problems associated with matching core to log data. Possible inaccuracies from the modelling of Ca-, Fe- and S-bearing minerals have been determined. A method for correcting the total measured aluminium concentration for that due to the borehole mud has been successfully tested against aluminium concentrations measured in the cleaned core samples. Estimates of the overall accuracy and precision of the elemental logging concentrations are obtained by comparing the log results with those obtained from the laboratory core analysis. A comprehensive core elemental analysis can also provide useful insight into the way other logs, such as the photoelectric factor or formation thermal neutron macroscopic absorption cross section, are influenced by minor and trace elements. Differences between calculated values from elemental logs and measured macroscopic parameters provide additional data for a more detailed understanding of the rock properties. (Author)

Importance of well logging measurements in the design of underground railway tunnels

International Nuclear Information System (INIS)

Kiss, E.Z.; Szlaboczky, P.

1981-01-01

The paper shows how logs can be used in the construction of underground railway tunnels in terciary sediments. Even standard well logging techniques (electric conductivity, gamma logging) can provide important additional information on the wells if conclusions concerning construction technology are gained from the logs. In the course of continuous research work the application of well logs renders an essential help if the measurements give in-situ information on absolute values of the well sections by revealing the various geological formations based on the distribution of characteristic parameters. Well logging increases the resolving power of the mechanical method of layer differentiation. Beside the usual geological interpretation of logs the zones of shifting rocks, hard and friable formations as well as intercalations leading to problems in construction technology can be pointed out. (author)

Using data logging to measure Young’s modulus

Science.gov (United States)

Richardson, David

2018-03-01

Historically the Young’s modulus of a material is measured by increasing the applied force to a wire and measuring the extension. The cross sectional area and original length allow this to be plotted as a graph of stress versus strain. This article describes how data logging sensors can be used to measure how the force changes with extension, allowing a strain versus stress graph to be plotted into the region of plastic deformation.

Simultaneous thermal neutron decay time and porosity logging system

International Nuclear Information System (INIS)

Smith, H.D. Jr.; Smith, M.P.; Schultz, W.E.

1979-01-01

A simultaneous pulsed neutron porosity and thermal neutron capture cross section logging system is provided for radiological well logging of subsurface earth formations. A logging tool provided with a 14 MeV pulsed neutron source, an epithermal neutron detector, and a combination gamma ray and fast neutron detector is moved through a borehole. Repetitive bursts of neutrons irradiate the earth formations; and, during the bursts, the fast neutron and epithermal neutron populations are sampled. During the interval between bursts the thermal neutron capture gamma ray population is sampled in two or more time intervals. The fast and epithermal neutron population measurements are combined to provide a measurement of formation porosity phi. The capture gamma ray measurements are combined to provide a simultaneous determination of the thermal neutron capture cross section Σ

Testing of a uranium downhole logging system to measure in-situ plutonium concentrations in sediments

International Nuclear Information System (INIS)

Kasper, R.B.; Kay, M.A.; Bruns, L.E.; Stokes, J.A.; Steinman, D.K.; Adams, J.

1980-11-01

A prototype urainium borehole logging system, developed for uranium exploration, was modified for Pu assay and testing at the site. It uses the delayed fission neutron (DFN) method. It was tested in a retired Pu facility, the 216-Z-1A Crib. General agreement between laboratory determined Pu concentrations in sediment samples and neutron flux measurements was found for the relative distribution with depth

Effects of holding time and measurement error on culturing Legionella in environmental water samples.

Science.gov (United States)

Flanders, W Dana; Kirkland, Kimberly H; Shelton, Brian G

2014-10-01

Outbreaks of Legionnaires' disease require environmental testing of water samples from potentially implicated building water systems to identify the source of exposure. A previous study reports a large impact on Legionella sample results due to shipping and delays in sample processing. Specifically, this same study, without accounting for measurement error, reports more than half of shipped samples tested had Legionella levels that arbitrarily changed up or down by one or more logs, and the authors attribute this result to shipping time. Accordingly, we conducted a study to determine the effects of sample holding/shipping time on Legionella sample results while taking into account measurement error, which has previously not been addressed. We analyzed 159 samples, each split into 16 aliquots, of which one-half (8) were processed promptly after collection. The remaining half (8) were processed the following day to assess impact of holding/shipping time. A total of 2544 samples were analyzed including replicates. After accounting for inherent measurement error, we found that the effect of holding time on observed Legionella counts was small and should have no practical impact on interpretation of results. Holding samples increased the root mean squared error by only about 3-8%. Notably, for only one of 159 samples, did the average of the 8 replicate counts change by 1 log. Thus, our findings do not support the hypothesis of frequent, significant (≥= 1 log10 unit) Legionella colony count changes due to holding. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Irrationality measures of $\\log 2$ and $\\pi/\\sqrt{3}$

OpenAIRE

Brisebarre, Nicolas

2001-01-01

Using a class of polynomials that generalizes Legendre polynomials, we unify previous works of E. A. Rukhadze, A. K. Dubitskas, M. Hata, D. V. and G. V. Chudnovsky about irrationality measures of $\\log 2$ and $\\pi/\\sqrt{3}$

Geophysical well-log measurements in three drill holes at Salt Valley, Utah

International Nuclear Information System (INIS)

Daniels, J.J.; Hite, R.J.; Scott, J.H.

1980-01-01

Three exploratory drill holes were drilled at Salt Valley, Utah, to study the geologic, physical, geochemical, and hydrologic properties of the evaporite sequence in the Permian Paradox Member of the Hermosa Formation. The results of these studies will be used to help to determine the suitability of salt deposits in the Paradox basin as a storage medium for radioactive waste material. The following geophysical well-log measurements were made in each of the three drill holes: (1) density, (2) neutron, (3) acoustic velocity, (4) normal resistivity, and (5) gamma ray. Widely spaced resistivity and conductivity well-log measurements were made in the deep drill hole. Each of these well-log measurements shows the division of the evaporite sequence into halite and interbed sections. At the present time the most useful well-logging measurements for determining the individual lithologies in an evaporite sequence are gamma ray, neutron, density, and acoustic velocity. The high resistivity contrast between the drilling fluid (0.5 ohm-m) and salt (10,000 ohm-m) makes it difficult to obtain quantitative measurements of electrical properties in an evaporite sequence. Tests of widely spaced electrode configurations show that the effects of the brine on the resistivity measurements can be reduced, and the depth of investigation increased, by increasing the source-receiver electrode spacing. Tests of a single-coil induction probe show good resolution of the contrasting electrical properties of the various interbed lithologies

Utilization and cost of log production from animal loging operations

Science.gov (United States)

Suraj P. Shrestha; Bobby L. Lanford; Robert B. Rummer; Mark Dubois

2006-01-01

Forest harvesting with animals is a labor-intensive operation. It is expensive to use machines on smaller woodlots, which require frequent moves if mechanically logged. So, small logging systems using animals may be more cost effective. In this study, work sampling was used for five animal logging operations in Alabama to measure productive and non-productive time...

Geophysical borehole logging in Lavia borehole - results and interpretation of sonic and tube wave measurements

International Nuclear Information System (INIS)

Andersson, P.; Stenberg, L.

1985-02-01

Swedish Nuclear Fuel and Waste Management Co, SKB has been contracted by Industrial Power Company LTD, TVO to perform geophysical logging in a borehole at Lavia in Western Finland. The logging has been conducted by Swedish Geological Co, SGAB in accordance with an agreement for cooperation with SKB. The depth of the borehole is 1001 m, diameter 56 mm and inclination 10-20 degrees to the vertical. The aim of the logging was to determine the various geophysical parameters in the borehole in order to interpret and understand the rock mass properties in the vicinity of the borehole. According to the contract the report covers the following main objectives: a technical description of the field work and the equipment used; a review of the theoretical base for the sonic and tube wave methods; an interpretation and presentation of the results obtained by sonic and tube wave mesurements. The evaluation of the sonic and tube wave measurements shows good correlation. On a qualitative basis there seems to be a correlation between tube wave generating points, the relative tube wave amplitudes and the hydraulic conductivity measurements performed as hydraulical tests between packers in the borehole. The low velocity anamalies in the sonic log are mainly caused by tectonic features like fractures and fracture zones but to some extent also by contacts between granite and diorite. The estimation of elastic properties of the rock mass from observation of tube wave velocity are in accordance with laboratory determinations made on core samples. (author)

Influence of borehole-eccentred tools on wireline and logging-while-drilling sonic logging measurements

KAUST Repository

Pardo, David

2013-02-13

We describe a numerical study to quantify the influence of tool-eccentricity on wireline (WL) and logging-while-drilling (LWD) sonic logging measurements. Simulations are performed with a height-polynomial-adaptive (hp) Fourier finite-element method that delivers highly accurate solutions of linear visco-elasto-acoustic problems in the frequency domain. The analysis focuses on WL instruments equipped with monopole or dipole sources and LWD instruments with monopole excitation. Analysis of the main propagation modes obtained from frequency dispersion curves indicates that the additional high-order modes arising as a result of borehole-eccentricity interfere with the main modes (i.e., Stoneley, pseudo-Rayleigh and flexural). This often modifies (decreases) the estimation of shear and compressional formation velocities, which should be corrected (increased) to account for borehole-eccentricity effects. Undesired interferences between different modes can occur at different frequencies depending upon the properties of the formation and fluid annulus size, which may difficult the estimation of the formation velocities. © 2013 European Association of Geoscientists & Engineers.

Automated method for measuring the extent of selective logging damage with airborne LiDAR data

Science.gov (United States)

Melendy, L.; Hagen, S. C.; Sullivan, F. B.; Pearson, T. R. H.; Walker, S. M.; Ellis, P.; Kustiyo; Sambodo, Ari Katmoko; Roswintiarti, O.; Hanson, M. A.; Klassen, A. W.; Palace, M. W.; Braswell, B. H.; Delgado, G. M.

2018-05-01

Selective logging has an impact on the global carbon cycle, as well as on the forest micro-climate, and longer-term changes in erosion, soil and nutrient cycling, and fire susceptibility. Our ability to quantify these impacts is dependent on methods and tools that accurately identify the extent and features of logging activity. LiDAR-based measurements of these features offers significant promise. Here, we present a set of algorithms for automated detection and mapping of critical features associated with logging - roads/decks, skid trails, and gaps - using commercial airborne LiDAR data as input. The automated algorithm was applied to commercial LiDAR data collected over two logging concessions in Kalimantan, Indonesia in 2014. The algorithm results were compared to measurements of the logging features collected in the field soon after logging was complete. The automated algorithm-mapped road/deck and skid trail features match closely with features measured in the field, with agreement levels ranging from 69% to 99% when adjusting for GPS location error. The algorithm performed most poorly with gaps, which, by their nature, are variable due to the unpredictable impact of tree fall versus the linear and regular features directly created by mechanical means. Overall, the automated algorithm performs well and offers significant promise as a generalizable tool useful to efficiently and accurately capture the effects of selective logging, including the potential to distinguish reduced impact logging from conventional logging.

Interpretation of horizontal well production logs: influence of logging tool

Energy Technology Data Exchange (ETDEWEB)

Ozkan, E. [Colorado School of Mines, Boulder, CO (United States); Sarica, C. [Pennsylvania State Univ., College Park, PA (United States); Haci, M. [Drilling Measurements, Inc (United States)

1998-12-31

The influence of a production-logging tool on wellbore flow rate and pressure measurements was investigated, focusing on the disturbence caused by the production-logging tool and the coiled tubing on the original flow conditions in the wellbore. The investigation was carried out using an analytical model and single-phase liquid flow was assumed. Results showed that the production-logging tool influenced the measurements as shown by the deviation of the original flow-rate, pressure profiles and low-conductivity wellbores. High production rates increase the effect of the production-logging tool. Recovering or inferring the original flow conditions in the wellbore from the production-logging data is a very complex process which cannot be solved easily. For this reason, the conditions under which the information obtained by production-logging is meaningful is of considerable practical interest. 7 refs., 2 tabs., 15 figs.

Borehole logging in uranium exploration

International Nuclear Information System (INIS)

Kulkarni, N.H.

1992-01-01

The ultimate objective of exploration by drilling as far as Atomic Minerals Division is concerned is to locate the ore zone in the subsurface, draw samples and analyze them for their metal content. The presence of the ore zone is also indicated by gamma-ray logging of the borehole. A gamma-ray detector is lowered in the borehole and precise depth and grade of the ore zone is established. This helps the geologist in correlating the ore horizon with the surface outcrop or the ore zone intercepted in adjoining boreholes and in deciding about further drilling and location of boreholes. Most commonly, total gamma measurements are made although some units capable of measuring the gamma-ray spectrum are also in use. It is possible to know if the mineralization is due to uranium without waiting for the laboratory results. The present write up gives a brief account of the principles, equipment and methods of borehole gamma-ray logging including density and self-potential logging. (author). 8 refs., 5 figs

Linearity improvement on wide-range log signal of neutron measurement system for HANARO

International Nuclear Information System (INIS)

Kim, Young-Ki; Tuetken, Jeffrey S.

1998-01-01

This paper discusses engineering activities for improving the linearity characteristics of the Log Power signal from the neutron measurement system for HANARO. This neutron measurement system uses a fission chamber based detector which covers 10.3 decade-wide range from 10 -8 % full power(FP) up to 200%FP, The Log Power signal is designed to control the reactor at low power levels where most of the reactor physics tests are carried out. Therefore, the linearity characteristics of the Log Power signal is the major factor for accurate reactor power control. During the commissioning of the neutron measurement system, it was found that the linearity characteristics of the Log Power signal, especially near 10 -2 %FP, were not accurate enough for controlling the reactor during physics testing. Analysis of the system linearity data directly measured with reactor operating determined that the system was not operating per the design characteristics established from previous installations. The linearity data, which were taken as the reactor was increased in power, were sent to manufacturer's engineering group and a follow-up measures based on the analysis were then fed back to the field. Through step by step trouble-shooting activities, which included minor circuit modifications and alignment procedure changes, the linearity characteristics have been successfully improved and now exceed minimum performance requirements. This paper discusses the trouble-shooting techniques applied, the changes in the linearity characteristics, special circumstances in the HANARO application and the final resolution. (author)

Development of a digital log ratemeter

International Nuclear Information System (INIS)

Domienikan, Claudio; Brito, Andreia; Toledo, Fabio de; Zahn, Guilherme S.

2011-01-01

A compact log ratemeter that measures and displays an average count rate through a microcomputer is presented. This ratemeter was developed to be used to monitor a laboratory of production of radioactive samples and also for teaching purposes. The main features are log measurement range from .1 to 1.000 counts/sec and adjustable level alarm. The electronic circuit uses a Geiger tube LND7224, and the processed signal is applied to a National Instruments Multifunction I/O USB-6008 connected to a PC through USB input. A program developed in LabView allows storage of data and real-time observation of the rate of radiation evolution. This ratemeter was designed and constructed in the IPEN-CNEN/SP. (author)

Pentachlorophenol measurements in body fluids of people in log homes and workplaces

Energy Technology Data Exchange (ETDEWEB)

Cline, R.E.; Hill, R.H. Jr.; Phillips, D.L.; Needham, L.L.

1989-07-01

Human exposure to pentachlorophenol (PCP) was evaluated in the normal population (controls), residents of PCP-treated log homes, and persons exposed primarily in the workplace. Blood and urine samples were analyzed by gas chromatography after extraction and acetylation. For 34 controls, serum PCP values ranged from 15-75 ppb with a mean of 40 ppb. For 123 residents of log homes, serum levels ranged from 69-1,340 ppb with a mean of 420 ppb. In such homes, serum levels for children were significantly higher than those for parents, averaging 1.8 times greater. Serum and urine values for workers varied widely, depending on the workplace, with serum levels ranging from 26 to 84,900 ppb of PCP. Urinary concentrations when corrected for creatinine values correlated well (r = 0.92) with serum concentrations. Coating PCP-treated logs of home interiors with a sealant reduced serum PCP levels in the residents.

Characterization of a complex near-surface structure using well logging and passive seismic measurements

Science.gov (United States)

Benjumea, Beatriz; Macau, Albert; Gabàs, Anna; Figueras, Sara

2016-04-01

We combine geophysical well logging and passive seismic measurements to characterize the near-surface geology of an area located in Hontomin, Burgos (Spain). This area has some near-surface challenges for a geophysical study. The irregular topography is characterized by limestone outcrops and unconsolidated sediments areas. Additionally, the near-surface geology includes an upper layer of pure limestones overlying marly limestones and marls (Upper Cretaceous). These materials lie on top of Low Cretaceous siliciclastic sediments (sandstones, clays, gravels). In any case, a layer with reduced velocity is expected. The geophysical data sets used in this study include sonic and gamma-ray logs at two boreholes and passive seismic measurements: three arrays and 224 seismic stations for applying the horizontal-to-vertical amplitude spectra ratio method (H/V). Well-logging data define two significant changes in the P-wave-velocity log within the Upper Cretaceous layer and one more at the Upper to Lower Cretaceous contact. This technique has also been used for refining the geological interpretation. The passive seismic measurements provide a map of sediment thickness with a maximum of around 40 m and shear-wave velocity profiles from the array technique. A comparison between seismic velocity coming from well logging and array measurements defines the resolution limits of the passive seismic techniques and helps it to be interpreted. This study shows how these low-cost techniques can provide useful information about near-surface complexity that could be used for designing a geophysical field survey or for seismic processing steps such as statics or imaging.

Method and apparatus for determining the spontaneous earth potential log from downhole gradient measurements

International Nuclear Information System (INIS)

Maciejewski, W. J.

1985-01-01

A method and apparatus for measuring the differential or gradient of an earth variable within a well bore (e.g., the spontaneous earth potential) and producing improved logs of this gradient or differential and its integral variable essentially free of any accumulated instrument and base line drift or error. The differential spontaneous potential of an earth formation traversed by a well bore is measured at repeated multiple depths by moving a pair of closely spaced electrodes through the well bore wherein each electrode is electrically insulated externally from the other and from a third downhole local ground (such as the well tool cable) to which each is internally resistively referenced. The measured electrical potential across the closely spaced electrodes is amplified and digitized before being transmitted to the earth's surface, whereupon an averaged value of such differential measurements within a traveling data window of predetermined length and adjacent to each successive measurement is used to adjust for base line drift, noise and instrument induced error. The resulting compensated differential logs are integrated, resulting in spontaneous potential logs of improved character

Study on the simulation of acoustic logging measurements in horizontal and deviated wells

Science.gov (United States)

Liu, He; Wang, Bing; Tao, Guo; Zhang, Kuo; Yue, Wen-Zheng

2017-09-01

The conventional acoustic logging interpretation method, which is based on vertical wells that penetrate isotropic formations, is not suitable for horizontal and deviated wells penetrating anisotropic formations. This unsuitability is because during horizontal and deviated well drilling, cuttings will splash on the well wall or fall into the borehole bottom and form a thin bed of cuttings. In addition, the high velocity layers at different depths and intrinsic anisotropy may affect acoustic logging measurements. In this study, we examine how these factors affect the acoustic wave slowness measured in horizontal and deviated wells that are surrounded by an anisotropic medium using numerical simulation. We use the staggered-grid finite difference method in time domain (FDTD) combined with hybrid-PML. First, we acquire the acoustic slowness using a simulated array logging system, and then, we analyze how various factors affect acoustic slowness measurements and the differences between the effects of these factors. The factors considered are high-velocity layers, thin beds of cuttings, dipping angle, formation thickness, and anisotropy. The simulation results show that these factors affect acoustic wave slowness measurements differently. We observe that when the wavelength is much smaller than the distance between the borehole wall and high velocity layer, the true slowness of the formation could be acquired. When the wavelengths are of the same order (i.e., in the near-field scenarios), the geometrical acoustics theory is no longer applicable. Furthermore, when a thin bed of cuttings exists at the bottom of the borehole, Fermat's principle is still applicable, and true slowness can be acquired. In anisotropic formations, the measured slowness changes with increments in the dipping angle. Finally, for a measurement system with specific spacing, the slowness of a thin target layer can be acquired when the distance covered by the logging tool is sufficiently long. Based

40 CFR 146.66 - Logging, sampling, and testing prior to new well operation.

Science.gov (United States)

2010-07-01

... cement bond and variable density log, and a temperature log after the casing is set and cemented. (ii..., gamma ray, and fracture finder logs before the casing is installed; and (B) A cement bond and variable density log, and a temperature log after the casing is set and cemented. (iii) The Director may allow the...

Interpretation of geophysical well-log measurements in drill hole UE25a-1, Nevada Test Site, Radioactive Waste Program

International Nuclear Information System (INIS)

Hagstrum, J.T.; Daniels, J.J.; Scott, J.H.

1980-01-01

An exploratory hole (UE25a-1) was drilled at Nevada Test Site (NTS) to determine the suitability of pyroclastic deposits as storage sites for radioactive waste. Studies have been conducted to investigate the stratigraphy, structure, mineralogy, petrology, and physical properties of the tuff units encountered in the drill hole. This report deals with the interpretation of physical properties for the tuff units from geophysical well-log measurements. The ash-flow and bedded tuff sequences at NTS comprise complex lithologies of variously welded tuffs with superimposed crystallization and altered zones. To characterize these units, resistivity, density, neutron, gamma-ray, induced polarization, and magnetic susceptibility geophysical well-log measurements were made. Although inherently subjective, a consistent interpretation of the well-log measurements was facilitated by a computer program designed to interpret well logs either individually or simultaneously. The broad features of the welded tuff units are readily distinguished by the geophysical well-log measurements. However, many details revealed by the logs indicate that more work is necessary to clarify the casual elements of well-log response in welded tuffs

hp-HGS strategy for inverse 3D DC resistivity logging measurement simulations

KAUST Repository

Gajda-Zaǵorska, Ewa; Paszý nski, Maciej; Schaefer, Robert; Pardo, David; Calo, Victor M.

2012-01-01

In this paper we present a twin adaptive strategy hp-HGS for solving inverse problems related to 3D DC borehole resistivity measurement simulations. The term “simulation of measurements” is widely used by the geophysical community. A quantity of interest, voltage, is measured at a receiver electrode located in the logging instrument. We use the self-adaptive goal-oriented hp-Finite Element Method (hp-FEM) computer simulations of the process of measurements in deviated wells (when the angle between the borehole and formation layers are < 90 deg). We also employ the hierarchical genetic search (HGS) algorithm to solve the inverse problem. Each individual in the population represents a single configuration of the formation layers. The evaluation of the individual is performed by solving the direct problem by means of the hp-FEM algorithm and by comparison with measured logging curve. We conclude the paper with some discussion on the parallelization of the algorithm.

hp-HGS strategy for inverse 3D DC resistivity logging measurement simulations

KAUST Repository

Gajda-Zaǵorska, Ewa

2012-06-02

In this paper we present a twin adaptive strategy hp-HGS for solving inverse problems related to 3D DC borehole resistivity measurement simulations. The term “simulation of measurements” is widely used by the geophysical community. A quantity of interest, voltage, is measured at a receiver electrode located in the logging instrument. We use the self-adaptive goal-oriented hp-Finite Element Method (hp-FEM) computer simulations of the process of measurements in deviated wells (when the angle between the borehole and formation layers are < 90 deg). We also employ the hierarchical genetic search (HGS) algorithm to solve the inverse problem. Each individual in the population represents a single configuration of the formation layers. The evaluation of the individual is performed by solving the direct problem by means of the hp-FEM algorithm and by comparison with measured logging curve. We conclude the paper with some discussion on the parallelization of the algorithm.

Pulse neutron logging technique

International Nuclear Information System (INIS)

Bespalov, D.F.; Dylyuk, A.A.

1975-01-01

A new method of neutron-burst logging is proposed, residing in irradiating rocks with fast neutron bursts and registering the integrated flux burst of thermal and/or epithermal neutrons, from the moment of its initiation to that of full absorption. The obtaained value is representative of the rock properties (porosity, hydrogen content). The integrated flux in a burst of thermal and epithermal neutrons can be measured both by way of activation of a reference sample of a known chemical composition during the neutron burst and by recording the radiation of induced activity of the sample within an interval between two bursts. The proposed method features high informative value, accuracy and efficiency

Testing of a uranium downhole logging system to measure in-situ plutonium concentrations in sediments. [216-Z-1A crib

Energy Technology Data Exchange (ETDEWEB)

Kasper, R.B.; Kay, M.A.; Bruns, L.E.; Stokes, J.A.; Steinman, D.K.; Adams, J.

1980-11-01

A prototype urainium borehole logging system, developed for uranium exploration, was modified for Pu assay and testing at the site. It uses the delayed fission neutron (DFN) method. It was tested in a retired Pu facility, the 216-Z-1A Crib. General agreement between laboratory determined Pu concentrations in sediment samples and neutron flux measurements was found for the relative distribution with depth.

Uranium favorability of tertiary sedimentary rocks of the Pend Oreille River valley, Washington. [Measurement and sampling of surface sections, collection of samples from isolated outcrops, chemical and mineralogical analyses of samples, and examination of available water logs

Energy Technology Data Exchange (ETDEWEB)

Marjaniemi, D.K.; Robins, J.W.

1975-08-01

Tertiary sedimentary rocks in the Pend Oreille River valley were investigated in a regional study to determine the favorability for potential uranium resources of northeastern Washington. This project involved measurement and sampling of surface sections, collection of samples from isolated outcrops, chemical and mineralogical analyses of samples, and examination of available water well logs. The Box Canyon Dam area north of Ione is judged to have very high favorability. Thick-bedded conglomerates interbedded with sandstones and silty sandstones compose the Tiger Formation in this area, and high radioactivity levels are found near the base of the formation. Uranophane is found along fracture surfaces or in veins. Carbonaceous material is present throughout the Tiger Formation in the area. Part of the broad Pend Oreille valley surrounding Cusick, Washington, is an area of high favorability. Potential host rocks in the Tiger Formation, consisting of arkosic sandstones interbedded with radioactive shales, probably extend throughout the subsurface part of this area. Carbonaceous material is present and some samples contain high concentrations of uranium. In addition, several other possible chemical indicators were found. The Tiger-Lost Creek area is rated as having medium favorability. The Tiger Formation contains very hard, poorly sorted granite conglomerate with some beds of arkosic sandstone and silty sandstone. The granite conglomerate was apparently derived from source rocks having relatively high uranium content. The lower part of the formation is more favorable than the upper part because of the presence of carbonaceous material, anomalously high concentrations of uranium, and other possible chemical indicators. The area west of Ione is judged to have low favorability, because of the very low permeability of the rocks and the very low uranium content. (auth)

A new NMR measuring instrument for logging while drilling; Ein neues Logging While Drilling Kernspinresonanz-Messgeraet

Energy Technology Data Exchange (ETDEWEB)

Fischer, D.M.; Thern, H.F.; Kruspe, T.; Blanz, M. [Baker Hughes INTEQ GmbH, Celle (Germany); Strobel, J. [RWE Dea AG, Hamburg (Germany)

2003-07-01

Since 1990, commercial wireline MR measurements are carried out in boreholes. Logging while drilling is a comparatively new technique, in which a MR sensor is integrated in the drilling equipment so that the measured data are available more quickly. Problems may be caused by movement of the drilling rig. The resulting vibrations may distort the MR signal. Current development activities therefore focus on design optimization for higher vibration stability. The contribution explains vibration-induced wrong measuring signals and presents measures to reduce the effects of vibration. Further, a new LWD-MR measuring instrument is presented, the so-called MagTrak{sup TM} which combines the quality and advantages of cable MR-T{sub 2} measurements with a minimum of vibration effects, as is shown by MR data from a commercial borehole. [German] Seit 1990 werden Wireline-MR-Messungen kommerziell im Bohrloch durchgefuehrt. In den letzten Jahren wird an Messgeraeten gearbeitet, die bereits waehrend des Bohrens MR-Daten aufzeichnen (Logging While Drilling, LWD). Dazu wird ein MR-Sensor in den Bohrstrang integriert. Neben der schnelleren Verfuegbarkeit der MR-Daten besteht ein grosser Vorteil der LWD-MR-Messung darin, dass die Daten bereits kurz nach dem Bohren gemessen werden. Die Invasion von Bohrlochspuelung in die Formation dauert dann noch nicht lange an, und die MR-Messung findet im relativ unveraenderten Gestein statt. Probleme beim Einsatz von MR-Messgeraeten waehrend des Bohrens werden vor allem durch die Bewegungen des Bohrstranges verursacht. Vibrationen des MR-Sensors fuehren zu veraenderten Messbedingungen waehrend des Messvorgangs, was zu Verzerrungen im MR-Signal fuehren kann. Den Aufbau des Messgeraetes so zu optimieren, dass Vibrationen einen moeglichst kleinen Einfluss auf die Messung haben, ist ein aktuelles Ziel der heutigen LWD-MR-Entwicklung. In diesem Artikel werden vibrationsverursachte Signalfehler erklaert und Massnahmen genannt, die die

Economic incentives exist to support measures to reduce illegal logging

Science.gov (United States)

J.A. Turner; J. Buongiorno; A. Katz; S. Zhu; R. Li

2008-01-01

Three studies of the global economic implications of eliminating illegal logging are summarized. Processors of illegally sourced wood would lose from the elimination of illegal logging through high prices for logs and decreased production of wood products. Associated with these changes could be losses in employment and income. Beyond these losses to the processing...

Formation factor logging in-situ by electrical methods. Background and methodology

International Nuclear Information System (INIS)

Loefgren, Martin; Neretnieks, Ivars

2002-10-01

Matrix diffusion has been identified as one of the most important mechanisms governing the retardation of radionuclides escaping from a deep geological repository for nuclear waste. Radionuclides dissolved in groundwater flowing in water-bearing fractures will diffuse into water filled micropores in the rock. Important parameters governing the matrix diffusion are the formation factor, the surface diffusion and sorption. This report focuses on the formation factor in undisturbed intrusive igneous rock and the possibility of measuring this parameter in-situ. The background to and the methodology of formation factor logging in-situ by electrical methods are given. The formation factor is here defined as a parameter only depending on the geometry of the porous system and not on the diffusing specie. Traditionally the formation factor has been measured by through diffusion experiments on core samples, which are costly and time consuming. It has been shown that the formation factor could also be measured by electrical methods that are faster and less expensive. Previously this has only been done quantitatively in the laboratory on a centimetre or decimetre scale. When measuring the formation factor in-situ in regions with saline groundwater only the rock resistivity and the pore water resistivity are needed. The rock resistivity could be obtained by a variety of geophysical downhole tools. Water-bearing fractures disturb the measurements and data possibly affected by free water has to be sorted out. This could be done without loosing too much data if the vertical resolution of the tool is high enough. It was found that the rock resistivity tool presently used by SKB are neither quantitative or have enough vertical resolution. Therefore the slimhole Dual-Laterolog from Antares was tested with good results. This tool has a high vertical resolution and gives quantitative rock resistivities that need no correction. At present there is no method of directly obtaining the

Formation factor logging in-situ by electrical methods. Background and methodology

Energy Technology Data Exchange (ETDEWEB)

Loefgren, Martin; Neretnieks, Ivars [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Chemical Engineering and Technology

2002-10-01

Matrix diffusion has been identified as one of the most important mechanisms governing the retardation of radionuclides escaping from a deep geological repository for nuclear waste. Radionuclides dissolved in groundwater flowing in water-bearing fractures will diffuse into water filled micropores in the rock. Important parameters governing the matrix diffusion are the formation factor, the surface diffusion and sorption. This report focuses on the formation factor in undisturbed intrusive igneous rock and the possibility of measuring this parameter in-situ. The background to and the methodology of formation factor logging in-situ by electrical methods are given. The formation factor is here defined as a parameter only depending on the geometry of the porous system and not on the diffusing specie. Traditionally the formation factor has been measured by through diffusion experiments on core samples, which are costly and time consuming. It has been shown that the formation factor could also be measured by electrical methods that are faster and less expensive. Previously this has only been done quantitatively in the laboratory on a centimetre or decimetre scale. When measuring the formation factor in-situ in regions with saline groundwater only the rock resistivity and the pore water resistivity are needed. The rock resistivity could be obtained by a variety of geophysical downhole tools. Water-bearing fractures disturb the measurements and data possibly affected by free water has to be sorted out. This could be done without loosing too much data if the vertical resolution of the tool is high enough. It was found that the rock resistivity tool presently used by SKB are neither quantitative or have enough vertical resolution. Therefore the slimhole Dual-Laterolog from Antares was tested with good results. This tool has a high vertical resolution and gives quantitative rock resistivities that need no correction. At present there is no method of directly obtaining the

MC simulation of the collimation effects on measurement precision of high-resolution logging

International Nuclear Information System (INIS)

Wu Wensheng; Xiao Lizhi

2010-01-01

In this paper,the MCNP code is used to calculate responses to detector counting rate and formation sensitivity in oil-well logging with different opening shapes and angles of the γ-ray source aperture and detector collimator. The results show that the opening shape and angle of the source aperture affect the measurement precision far more than the opening shape and angle of the detector collimator, and the influences are greater than that of the formation sensitivity. A logging system that is equipped with a γ-ray source having a cuniform aperture of 45 degree opening angle, and a window aperture of 0 degree opening angle for a long-spacing detector or a short-spacing detector, and 5 degree-15 degree opening angle for a middle-spacing detector, will improve the measurement precision. (authors)

Explorations in statistics: the log transformation.

Science.gov (United States)

Curran-Everett, Douglas

2018-06-01

Learning about statistics is a lot like learning about science: the learning is more meaningful if you can actively explore. This thirteenth installment of Explorations in Statistics explores the log transformation, an established technique that rescales the actual observations from an experiment so that the assumptions of some statistical analysis are better met. A general assumption in statistics is that the variability of some response Y is homogeneous across groups or across some predictor variable X. If the variability-the standard deviation-varies in rough proportion to the mean value of Y, a log transformation can equalize the standard deviations. Moreover, if the actual observations from an experiment conform to a skewed distribution, then a log transformation can make the theoretical distribution of the sample mean more consistent with a normal distribution. This is important: the results of a one-sample t test are meaningful only if the theoretical distribution of the sample mean is roughly normal. If we log-transform our observations, then we want to confirm the transformation was useful. We can do this if we use the Box-Cox method, if we bootstrap the sample mean and the statistic t itself, and if we assess the residual plots from the statistical model of the actual and transformed sample observations.

Results of investigations at the Zunil geothermal field, Guatemala: Well logging and brine geochemistry

Energy Technology Data Exchange (ETDEWEB)

Adams, A.; Dennis, B.; Van Eeckhout, E.; Goff, F.; Lawton, R.; Trujillo, P.E.; Counce, D.; Archuleta, J. (Los Alamos National Lab., NM (USA)); Medina, V. (Instituto Nacional de Electrificacion, Guatemala City (Guatemala). Unidad de Desarollo Geotermico)

1991-07-01

The well logging team from Los Alamos and its counterpart from Central America were tasked to investigate the condition of four producing geothermal wells in the Zunil Geothermal Field. The information obtained would be used to help evaluate the Zunil geothermal reservoir in terms of possible additional drilling and future power plant design. The field activities focused on downhole measurements in four production wells (ZCQ-3, ZCQ-4, ZCQ-5, and ZCQ-6). The teams took measurements of the wells in both static (shut-in) and flowing conditions, using the high-temperature well logging tools developed at Los Alamos National Laboratory. Two well logging missions were conducted in the Zunil field. In October 1988 measurements were made in well ZCQ-3, ZCQ-5, and ZCQ-6. In December 1989 the second field operation logged ZCQ-4 and repeated logs in ZCQ-3. Both field operations included not only well logging but the collecting of numerous fluid samples from both thermal and nonthermal waters. 18 refs., 22 figs., 7 tabs.

Unification of acoustic drillhole logging data

International Nuclear Information System (INIS)

Oehman, I.; Palmen, J.; Heikkinen, E.

2009-04-01

...KR4, OL-KR6...KR20 and OLKR22... KR28 were reprocessed and computed to P and S wave velocity values. Procedure included resampling, filtering, time picking and stand-off correction. Velocity levels were calibrated comparable between drillholes by comparing with petrophysical sample data for specific drillholes and for site distribution. Calibration was based on setting the distribution modes uniform. Also gamma-gamma density logging was readjusted to a common level in each drillhole. Data sets were depth correlated to geological check points like fractures and rock type contacts and adjusted. Finally dynamic elastic modulii were computed. Tentative comparison was carried out to rock strength laboratory data. As the logging data is now on a common level and comparable resolution, it would be also possible to use the results for interpretation of the seismic reflection measurements carried out in the Olkiluoto site. The acoustic logging is an important link between petrophysical data from core samples and site scale seismic reflection measurements. It offers a continuous data set from complete drillhole length. (orig.)

Iowa Geologic Sampling Points

Data.gov (United States)

Iowa State University GIS Support and Research Facility — Point locations of geologic samples/files in the IGS repository. Types of samples include well cuttings, outcrop samples, cores, drillers logs, measured sections,...

Development of self-learning Monte Carlo technique for more efficient modeling of nuclear logging measurements

International Nuclear Information System (INIS)

Zazula, J.M.

1988-01-01

The self-learning Monte Carlo technique has been implemented to the commonly used general purpose neutron transport code MORSE, in order to enhance sampling of the particle histories that contribute to a detector response. The parameters of all the biasing techniques available in MORSE, i.e. of splitting, Russian roulette, source and collision outgoing energy importance sampling, path length transformation and additional biasing of the source angular distribution are optimized. The learning process is iteratively performed after each batch of particles, by retrieving the data concerning the subset of histories that passed the detector region and energy range in the previous batches. This procedure has been tested on two sample problems in nuclear geophysics, where an unoptimized Monte Carlo calculation is particularly inefficient. The results are encouraging, although the presented method does not directly minimize the variance and the convergence of our algorithm is restricted by the statistics of successful histories from previous random walk. Further applications for modeling of the nuclear logging measurements seem to be promising. 11 refs., 2 figs., 3 tabs. (author)

Radiometric well logging instruments

International Nuclear Information System (INIS)

Davydov, A.V.

1975-01-01

The technical properties of well instruments for radioactive logging used in the radiometric logging complexes PKS-1000-1 (''Sond-1'') and PRKS-2 (''Vitok-2'') are described. The main features of the electric circuit of the measuring channels are given

Core sample descriptions and summary logs of six wells within the Hanford Reservation

International Nuclear Information System (INIS)

Summers, W.K.; Hanson, R.T.

1977-01-01

From February through May, 1976, selected sites on the Hanford Reservation were core drilled. These six holes provide a loose network of observation holes traversing the reservation in an east--west direction between the Columbia River and State Highway 240. This program represents the first attempt to recover cores from the glaciofluviatile material and Ringold Formation beneath the Hanford Reservation. This contains three parts: an introductory text describing the method of inspection and format for written description; summary logs that illustrate in condensed form the rocks penetrated by the wells drilled; and the detailed written descriptions of core samples. 3 figures, 7 tables

PUMA Internet Task Logging Using the IDAC-1

Directory of Open Access Journals (Sweden)

K. N. Tarchanidis

2014-08-01

Full Text Available This project uses an IDAC-1 board to sample the joint angle position of the PUMA 76 1 robot and log the results on a computer. The robot is at the task location and the logging computer is located in a different one. The task the robot is performing is based on a Pseudo Stereo Vision System (PSVS. Internet is the transport media. The protocol used in this project is UDP/IP. The actual angle is taken straight from the PUMA controller. High-resolution potentiometers are connected on each robot joint and are buffered and sampled as potential difference on an A/D converter integrated on the IDAC-1. The logging computer through the Internet acting as client asks for the angle set, the IDAC-1 responds as server with the 10-bit resolution sampling of the joint position. The whole task is logged in a file on the logging computer. This application can give the ability to the Internet user to monitor and log the robot tasks anywhere in the Word Wide Web (www.

Correlated sampling added to the specific purpose Monte Carlo code McPNL for neutron lifetime log responses

International Nuclear Information System (INIS)

Mickael, M.; Verghese, K.; Gardner, R.P.

1989-01-01

The specific purpose neutron lifetime oil well logging simulation code, McPNL, has been rewritten for greater user-friendliness and faster execution. Correlated sampling has been added to the code to enable studies of relative changes in the tool response caused by environmental changes. The absolute responses calculated by the code have been benchmarked against laboratory test pit data. The relative responses from correlated sampling are not directly benchmarked, but they are validated using experimental and theoretical results

Accounting for measurement error in log regression models with applications to accelerated testing.

Science.gov (United States)

Richardson, Robert; Tolley, H Dennis; Evenson, William E; Lunt, Barry M

2018-01-01

In regression settings, parameter estimates will be biased when the explanatory variables are measured with error. This bias can significantly affect modeling goals. In particular, accelerated lifetime testing involves an extrapolation of the fitted model, and a small amount of bias in parameter estimates may result in a significant increase in the bias of the extrapolated predictions. Additionally, bias may arise when the stochastic component of a log regression model is assumed to be multiplicative when the actual underlying stochastic component is additive. To account for these possible sources of bias, a log regression model with measurement error and additive error is approximated by a weighted regression model which can be estimated using Iteratively Re-weighted Least Squares. Using the reduced Eyring equation in an accelerated testing setting, the model is compared to previously accepted approaches to modeling accelerated testing data with both simulations and real data.

Accounting for measurement error in log regression models with applications to accelerated testing.

Directory of Open Access Journals (Sweden)

Robert Richardson

Full Text Available In regression settings, parameter estimates will be biased when the explanatory variables are measured with error. This bias can significantly affect modeling goals. In particular, accelerated lifetime testing involves an extrapolation of the fitted model, and a small amount of bias in parameter estimates may result in a significant increase in the bias of the extrapolated predictions. Additionally, bias may arise when the stochastic component of a log regression model is assumed to be multiplicative when the actual underlying stochastic component is additive. To account for these possible sources of bias, a log regression model with measurement error and additive error is approximated by a weighted regression model which can be estimated using Iteratively Re-weighted Least Squares. Using the reduced Eyring equation in an accelerated testing setting, the model is compared to previously accepted approaches to modeling accelerated testing data with both simulations and real data.

AML (Advanced Mud Logging: First Among Equals

Directory of Open Access Journals (Sweden)

T. Loermans

2017-09-01

Full Text Available During the past ten years an enormous development in mud logging technology has been made. Traditional mud logging was only qualitative in nature, and mudlogs could not be used for the petrophysical well evaluations which form the basis for all subsequent activities on wells and fields. AML however can provide quantitative information, logs with a reliability, trueness and precision like LWD and WLL. Hence for well evaluation programmes there are now three different logging methods available, each with its own pros and cons on specific aspects: AML, LWD and WLL. The largest improvements have been made in mud gas analysis and elemental analysis of cuttings. Mud gas analysis can yield hydrocarbon fluid composition for some components with a quality like PVT analysis, hence not only revolutionising the sampling programme so far done with only LWD/WLL, but also making it possible to geosteer on fluid properties. Elemental analysis of cuttings, e.g. with XRF, with an ability well beyond the capabilities of the spectroscopy measurements possible earlier with LWD/WLL tools, is opening up improved ways to evaluate formations, especially of course where the traditional methods are falling short of requirements, such as in unconventional reservoirs. An overview and specific examples of these AML logs is given, from which it may be concluded that AML now ought to be considered as “first among its equals”.

Effect of selective logging on genetic diversity and gene flow in Cariniana legalis sampled from a cacao agroforestry system.

Science.gov (United States)

Leal, J B; Santos, R P; Gaiotto, F A

2014-01-28

The fragments of the Atlantic Forest of southern Bahia have a long history of intense logging and selective cutting. Some tree species, such as jequitibá rosa (Cariniana legalis), have experienced a reduction in their populations with respect to both area and density. To evaluate the possible effects of selective logging on genetic diversity, gene flow, and spatial genetic structure, 51 C. legalis individuals were sampled, representing the total remaining population from the cacao agroforestry system. A total of 120 alleles were observed from the 11 microsatellite loci analyzed. The average observed heterozygosity (0.486) was less than the expected heterozygosity (0.721), indicating a loss of genetic diversity in this population. A high fixation index (FIS = 0.325) was found, which is possibly due to a reduction in population size, resulting in increased mating among relatives. The maximum (1055 m) and minimum (0.095 m) distances traveled by pollen or seeds were inferred based on paternity tests. We found 36.84% of unique parents among all sampled seedlings. The progenitors of the remaining seedlings (63.16%) were most likely out of the sampled area. Positive and significant spatial genetic structure was identified in this population among classes 10 to 30 m away with an average coancestry coefficient between pairs of individuals of 0.12. These results suggest that the agroforestry system of cacao cultivation is contributing to maintaining levels of diversity and gene flow in the studied population, thus minimizing the effects of selective logging.

A method of estimating log weights.

Science.gov (United States)

Charles N. Mann; Hilton H. Lysons

1972-01-01

This paper presents a practical method of estimating the weights of logs before they are yarded. Knowledge of log weights is required to achieve optimum loading of modern yarding equipment. Truckloads of logs are weighed and measured to obtain a local density index (pounds per cubic foot) for a species of logs. The density index is then used to estimate the weights of...

Digital mineral logging system

International Nuclear Information System (INIS)

West, J.B.

1980-01-01

A digital mineral logging system acquires data from a mineral logging tool passing through a borehole and transmits the data uphole to an electronic digital signal processor. A predetermined combination of sensors, including a deviometer, is located in a logging tool for the acquisition of the desired data as the logging tool is raised from the borehole. Sensor data in analog format is converted in the logging tool to a digital format and periodically batch transmitted to the surface at a predetermined sampling rate. An identification code is provided for each mineral logging tool, and the code is transmitted to the surface along with the sensor data. The self-identifying tool code is transmitted to the digital signal processor to identify the code against a stored list of the range of numbers assigned to that type of tool. The data is transmitted up the d-c power lines of the tool by a frequency shift key transmission technique. At the surface, a frequency shift key demodulation unit transmits the decoupled data to an asynchronous receiver interfaced to the electronic digital signal processor. During a recording phase, the signals from the logging tool are read by the electronic digital signal processor and stored for later processing. During a calculating phase, the stored data is processed by the digital signal processor and the results are outputted to a printer or plotter, or both

Geophysical borehole logging in the unsaturated zone, Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Schimschal, U.; Nelson, P.H.

1991-01-01

Borehole geophysical logging for site characterization in the volcanic rocks at the proposed nuclear waste repository at Yucca Mountain, Nevada, requires data collection under rather unusual conditions. Logging tools must operate in rugose, dry holes above the water table in the unsaturated zone. Not all logging tools will operate in this environment, therefore; careful consideration must be given to selection and calibration. A sample suite of logs is presented that demonstrates correlation of geological formations from borehole to borehole, the definition of zones of altered mineralogy, and the quantitative estimates of rock properties. The authors show the results of an exploratory calculation of porosity and water saturation based upon density and epithermal neutron logs. Comparison of the results with a few core samples is encouraging, particularly because the logs can provide continuous data in boreholes where core samples are not available

A new type of compensated neutron logging probe

International Nuclear Information System (INIS)

Ji Changsong; Shang Xiulan; Dai Zhude; Huang Heyi; Zhang Jianguo; Zu Shihuan; Zhao Jianqiang

1988-01-01

A new type of compensated neutron logging probe with glass scintillators has been designed. High sensitivity, long plateau and stability are the features of this probe which differs from the probes with 3 He or LiI(Eu) detector. From the results of field application the measured porosity is in good correspondence with the one obtained by rock core sampling method

Nuclear well logging in hydrology

International Nuclear Information System (INIS)

1971-01-01

The optimum development of regional and local groundwater resources requires a quantitative evaluation of its aquifers and aquicludes, and of the physical and chemical properties relevant to the recharge to and withdrawal of water from them. If an understanding of the groundwater regime is to be obtained, geological observations at outcrop must be augmented by subsurface measurements of the strata and the waters they contain. Measurements of many hydrological and geological parameters can be made in situ by nuclear geophysical well-logging methods. Very simply, well logging consists of lowering a measuring probe into a well and making a continuous record of the variations of a particular parameter with depth. In most circumstances, repetition of the measurements under differing hydrodynamic conditions results in a better definition of the flow regime in the aquifer. Nuclear well-logging techniques have for some years been capable of solving a number of the sub-surface measurement problems faced by hydrogeologists. However, the present usage of these methods varies from country to country and the literature concerning applications is scattered in the professional journals of several disciplines. The objective of this report is to include in a single reference volume descriptions of the physical principles of nuclear logging methods, their applications to hydrogeological problems and their limitations on a level suitable for the practising hydrologists with a limited knowledge of nuclear physics. The Working Group responsible for compiling the report recommended that it should cover a broad spectrum of hydrogeological investigations and problems. For example, it saw no valid reason to distinguish for the purposes of the report between well-logging applications for water-supply purposes and for water-flooding studies in the petroleum industry. Neutron measurements made for soil-moisture determinations in the unsaturated zone have been specifically omitted, however, as

Adaptive sampling of AEM transients

Science.gov (United States)

Di Massa, Domenico; Florio, Giovanni; Viezzoli, Andrea

2016-02-01

This paper focuses on the sampling of the electromagnetic transient as acquired by airborne time-domain electromagnetic (TDEM) systems. Typically, the sampling of the electromagnetic transient is done using a fixed number of gates whose width grows logarithmically (log-gating). The log-gating has two main benefits: improving the signal to noise (S/N) ratio at late times, when the electromagnetic signal has amplitudes equal or lower than the natural background noise, and ensuring a good resolution at the early times. However, as a result of fixed time gates, the conventional log-gating does not consider any geological variations in the surveyed area, nor the possibly varying characteristics of the measured signal. We show, using synthetic models, how a different, flexible sampling scheme can increase the resolution of resistivity models. We propose a new sampling method, which adapts the gating on the base of the slope variations in the electromagnetic (EM) transient. The use of such an alternative sampling scheme aims to get more accurate inverse models by extracting the geoelectrical information from the measured data in an optimal way.

Status report on the development of a prompt fission neutron uranium borehole logging technique

International Nuclear Information System (INIS)

Smith, G.W.

1977-05-01

The prompt fission neutron (PFN) method of direct uranium measurement was studied. The PFN uranium logging technique measures the enhanced epithermal neutron population created by the prompt thermal fission of 235 U to assay uranium mineralization around a borehole. This neutron population exists for several hundred microseconds after a pulsed neutron source produces a burst of high energy (14 MeV) neutrons. A feasibility study established the basic relationship between the uranium concentration and the enhanced epithermal neutron count, and defined the major measurement perturbing factors. Following the feasibility study, development of a PFN prototype field probe was undertaken. A laboratory type neutron generator, the Controlatron, was modified for use in the probe. Field evaluation of the prototype system began in January 1976. Comparisons of neutron logs and natural gamma logs taken during this evaluation period clearly define many disequilibrium conditions as verified by ore grade estimates from core samples. The feasibility of the PFN logging technique to detect uranium in-situ has now been demonstrated

Earth formation porosity log using measurement of neutron energy spectrum

International Nuclear Information System (INIS)

1981-01-01

Methods and apparatus are described for measuring the porosity of subsurface earth formations in the vicinity of a well borehole by means of neutron well logging techniques. All the commercial techniques for measuring porosity currently available are not as accurate as desirable due to variations in the borehole wall diameter, in the borehole fluids (e.g. with chlorine content) in the casings of the borehole etc. This invention seeks to improve accuracy by using a measurement of the epithermal neutron population at one detector and the fast neutron population at a second detector, spaced approximately the same distance from a neutron source. The latter can be detected either by a fast neutron detector or indirectly by an inelastic gamma ray detector. Background correction can be made, and special detectors used, to discriminate against the detection of thermal neutrons or their resultant capture gamma rays. These fluctuations affect the measurement of thermal neutron populations. (U.K.)

Selective logging in the Brazilian Amazon.

Science.gov (United States)

G. P. Asner; D. E. Knapp; E. N. Broadbent; P. J. C. Oliveira; M Keller; J. N. Silva

2005-01-01

Amazon deforestation has been measured by remote sensing for three decades. In comparison, selective logging has been mostly invisible to satellites. We developed a large-scale, high-resolution, automated remote-sensing analysis of selective logging in the top five timber-producing states of the Brazilian Amazon. Logged areas ranged from 12,075 to 19,823 square...

Quantification of Wellbore Leakage Risk Using Non-destructive Borehole Logging Techniques

Energy Technology Data Exchange (ETDEWEB)

Duguid, Andrew; Butsch, Robert; Cary, J.; Celia, Michael; Chugunov, Nikita; Gasda, Sarah; Hovorka, Susan; Ramakrishnan, T. S.; Stamp, Vicki; Thingelstad, Rebecca; Wang, James

2014-08-29

Well integrity is important at all potential CCS locations and may play a crucial role establishing leakage risk in areas where there is a high density of existing wells that could be impacted by the storage operations including depleted petroleum fields where EOR or CCS will occur. To address a need for risk quantification methods that can be directly applied to individual wells using borehole logging tools a study was conducted using data from five wells in Wyoming. The objectives of the study were: Objective 1: Develop methods to establish the baseline flow parameters (porosity and permeability or mobility) from individual measurements of the material properties and defects in a well. Objective 2: Develop a correlation between field flow-property data and cement logs that can be used to establish the flow-properties of well materials and well features using cement mapping tools. Objective 3: Establish a method that uses the flow-property model (Objective 2) to analyze the statistical uncertainties associated with individual well leakage that can provide basis for uncertainty in risk calculations. The project objectives were met through the logging of five wells in Carbon and Natrona County Wyoming to collect data that was used to estimate individual and average well flow properties and model the results using ultrasonic data collected during the logging. Three of the five wells provided data on point and average flow properties for well annuli. Data from the other two wells were used to create models of cement permeability and test whether information collected in one well could be used to characterize another well. The results of the in-situ point measurements were confirmed by the lab measurements sidewall cores collected near the same depths Objective 1 was met using the data collected through logging, testing, and sampling. The methods were developed that can establish baseline flow parameters of wells by both point and average test methods. The methods to

Pulsed radiation decay logging

International Nuclear Information System (INIS)

Mills, W.R. Jr.

1983-01-01

There are provided new and improved well logging processes and systems wherein the detection of secondary radiation is accomplished during a plurality of time windows in a manner to accurately characterize the decay rate of the secondary radiation. The system comprises a well logging tool having a primary pulsed radiation source which emits repetitive time-spaced bursts of primary radiation and detector means for detecting secondary radiation resulting from the primary radiation and producing output signals in response to the detected radiation. A plurality of measuring channels are provided, each of which produces a count rate function representative of signals received from the detector means during successive time windows occurring between the primary radiation bursts. The logging system further comprises means responsive to the measuring channels for producing a plurality of functions representative of the ratios of the radiation count rates measured during adjacent pairs of the time windows. Comparator means function to compare the ratio functions and select at least one of the ratio functions to generate a signal representative of the decay rate of the secondary radiation

Basalt identification by interpreting nuclear and electrical well logging measurements using fuzzy technique (case study from southern Syria)

International Nuclear Information System (INIS)

Asfahani, J.; Abdul Ghani, B.; Ahmad, Z.

2015-01-01

Fuzzy analysis technique is proposed in this research for interpreting the combination of nuclear and electrical well logging data, which include natural gamma ray, density and neutron-porosity, while the electrical well logging include long and short normal. The main objective of this work is to describe, characterize and establish the lithology of the large extended basaltic areas in southern Syria. Kodana well logging measurements have been used and interpreted for testing and applying the proposed technique. The established lithological cross section shows the distribution and the identification of four kinds of basalt, which are hard massive basalt, hard basalt, pyroclastic basalt and the alteration basalt products, clay. The fuzzy analysis technique is successfully applied on the Kodana well logging data, and can be therefore utilized as a powerful tool for interpreting huge well logging data with higher number of variables required for lithological estimations. - Highlights: • Apply fuzzy analysis technique on the nuclear and electrical well logging data of Kodana well in Southern Syria. • Determine and differentiate between four kinds of basalt. • Establish the lithological section of the studied well.

Earth formation pulsed neutron porosity logging system utilizing epithermal neutron and inelastic scattering gamma ray detectors

International Nuclear Information System (INIS)

Smith, H.D. Jr.; Smith, M.P.; Schultz, W.E.

1978-01-01

An improved pulsed neutron porosity logging system is provided in the present invention. A logging tool provided with a 14 MeV pulsed neutron source, an epithermal neutron detector and an inelastic scattering gamma ray detector is moved through a borehole. The detection of inelastic gamma rays provides a measure of the fast neutron population in the vicinity of the detector. repetitive bursts of neutrons irradiate the earth formation and, during the busts, inelastic gamma rays representative of the fast neutron population is sampled. During the interval between bursts the epithermal neutron population is sampled along with background gamma radiation due to lingering thermal neutrons. the fast and epithermal neutron population measurements are combined to provide a measurement of formation porosity

Towards an entropy-based analysis of log variability

DEFF Research Database (Denmark)

Back, Christoffer Olling; Debois, Søren; Slaats, Tijs

2017-01-01

the development of hybrid miners: given a (sub-)log, can we determine a priori whether the log is best suited for imperative or declarative mining? We propose using the concept of entropy, commonly used in information theory. We consider different measures for entropy that could be applied and show through...... experimentation on both synthetic and real-life logs that these entropy measures do indeed give insights into the complexity of the log and can act as an indicator of which mining paradigm should be used....

Towards an Entropy-based Analysis of Log Variability

DEFF Research Database (Denmark)

Back, Christoffer Olling; Debois, Søren; Slaats, Tijs

2018-01-01

the development of hybrid miners: given a log, can we determine a priori whether the log is best suited for imperative or declarative mining? We propose using the concept of entropy, commonly used in information theory. We consider different measures for entropy that could be applied and show through...... experimentation on both synthetic and real-life logs that these entropy measures do indeed give insights into the complexity of the log and can act as an indicator of which mining paradigm should be used....

SU-G-BRB-04: Automated Output Factor Measurements Using Continuous Data Logging for Linac Commissioning

Energy Technology Data Exchange (ETDEWEB)

Zhu, X; Li, S; Zheng, D; Wang, S; Lei, Y; Zhang, M; Ma, R; Fan, Q; Wang, X; Li, X; Verma, V; Enke, C; Zhou, S [University of Nebraska Medical Center, Omaha, NE (United States)

2016-06-15

Purpose: Linac commissioning is a time consuming and labor intensive process, the streamline of which is highly desirable. In particular, manual measurement of output factors for a variety of field sizes and energy greatly hinders the commissioning efficiency. In this study, automated measurement of output factors was demonstrated as ‘one-click’ using data logging of an electrometer. Methods: Beams to be measured were created in the recording and verifying (R&V) system and configured for continuous delivery. An electrometer with an automatic data logging feature enabled continuous data collection for all fields without human intervention. The electrometer saved data into a spreadsheet every 0.5 seconds. A Matlab program was developed to analyze the excel data to monitor and check the data quality. Results: For each photon energy, output factors were measured for five configurations, including open field and four wedges. Each configuration includes 72 fields sizes, ranging from 4×4 to 20×30 cm{sup 2}. Using automation, it took 50 minutes to complete the measurement of 72 field sizes, in contrast to 80 minutes when using the manual approach. The automation avoided the necessity of redundant Linac status checks between fields as in the manual approach. In fact, the only limiting factor in such automation is Linac overheating. The data collection beams in the R&V system are reusable, and the simplified process is less error-prone. In addition, our Matlab program extracted the output factors faithfully from data logging, and the discrepancy between the automatic and manual measurement is within ±0.3%. For two separate automated measurements 30 days apart, consistency check shows a discrepancy within ±1% for 6MV photon with a 60 degree wedge. Conclusion: Automated output factor measurements can save time by 40% when compared with conventional manual approach. This work laid ground for further improvement for the automation of Linac commissioning.

SU-G-BRB-04: Automated Output Factor Measurements Using Continuous Data Logging for Linac Commissioning

International Nuclear Information System (INIS)

Zhu, X; Li, S; Zheng, D; Wang, S; Lei, Y; Zhang, M; Ma, R; Fan, Q; Wang, X; Li, X; Verma, V; Enke, C; Zhou, S

2016-01-01

Purpose: Linac commissioning is a time consuming and labor intensive process, the streamline of which is highly desirable. In particular, manual measurement of output factors for a variety of field sizes and energy greatly hinders the commissioning efficiency. In this study, automated measurement of output factors was demonstrated as ‘one-click’ using data logging of an electrometer. Methods: Beams to be measured were created in the recording and verifying (R&V) system and configured for continuous delivery. An electrometer with an automatic data logging feature enabled continuous data collection for all fields without human intervention. The electrometer saved data into a spreadsheet every 0.5 seconds. A Matlab program was developed to analyze the excel data to monitor and check the data quality. Results: For each photon energy, output factors were measured for five configurations, including open field and four wedges. Each configuration includes 72 fields sizes, ranging from 4×4 to 20×30 cm"2. Using automation, it took 50 minutes to complete the measurement of 72 field sizes, in contrast to 80 minutes when using the manual approach. The automation avoided the necessity of redundant Linac status checks between fields as in the manual approach. In fact, the only limiting factor in such automation is Linac overheating. The data collection beams in the R&V system are reusable, and the simplified process is less error-prone. In addition, our Matlab program extracted the output factors faithfully from data logging, and the discrepancy between the automatic and manual measurement is within ±0.3%. For two separate automated measurements 30 days apart, consistency check shows a discrepancy within ±1% for 6MV photon with a 60 degree wedge. Conclusion: Automated output factor measurements can save time by 40% when compared with conventional manual approach. This work laid ground for further improvement for the automation of Linac commissioning.

A first look at logging residue characteristics in West Virginia

Science.gov (United States)

A. Jeff Martin

1975-01-01

In 1973 and 1974, the Forest Products Marketing Laboratory obtained some preliminary information about characteristics of logging residues in West Virginia. Sixteen 1-acre plots were measured in conjunction with a test of the line-intersect sampling method. Findings from the 16 plots showed that hardwood residue volumes ranged from 100 to 1,300 cubic feet per acre,...

Limitations and developing directions of pulsed neutron logging

International Nuclear Information System (INIS)

Wu Wensheng; Xiao Lizhi

2007-01-01

The paper explains briefly the principle of pulsed neutron logging method, summarizes the system and uses of the method in petroleum logging. The paper points out the limitations of pulsed neutron logging such as low precise measurements, low logging speed, plenty of influence factors, low vertical resolution, bad adaptability, difficult logging interpretation and so on, and expounds its developing directions in hardware, software, method and principle. (authors)

Geophysical logging of the Harwell boreholes

International Nuclear Information System (INIS)

Brightman, M.A.

1983-08-01

A comprehensive geophysical borehole logging survey was carried out on each of three deep boreholes drilled at the Harwell research site. KOALA and PETRA computer programs were used to analyse and interpret the logs to obtain continuous quantitative estimates of the geological and hydrogeological properties of the sequences penetrated at the Harwell site. Quantitative estimates of the mineral composition and porosity of the cores samples were made. (UK)

In silico sampling reveals the effect of clustering and shows that the log-normal rank abundance curve is an artefact

NARCIS (Netherlands)

Neuteboom, J.H.; Struik, P.C.

2005-01-01

The impact of clustering on rank abundance, species-individual (S-N)and species-area curves was investigated using a computer programme for in silico sampling. In a rank abundance curve the abundances of species are plotted on log-scale against species sequence. In an S-N curve the number of species

The use of MP3 recorders to log data from equine hoof mounted accelerometers.

Science.gov (United States)

Parsons, K J; Wilson, A M

2006-11-01

MP3 recorders are readily available, small, lightweight and low cost, providing the potential for logging analogue hoof mounted accelerometer signals for the characterisation of equine locomotion. These, however, require testing in practice. To test whether 1) multiple MP3 recorders can maintain synchronisation, giving the ability to synchronise independent recorders for the logging of multiple limbs simultaneously; and 2) features of a foot mounted accelerometer signal attributable to foot-on and foot-off can be accurately identified from horse foot mounted accelerometers logged directly into an MP3 recorder. Three experiments were performed: 1) Maintenance of synchronisation was assessed by counting the number of samples recorded by each of 4 MP3 recorders while mounted on a trotting horse and over 2 consecutive 30 min periods in 8 recorders on a bench. 2) Foot-on and foot-off times obtained from manual transcription of MP3 logged data and directly logged accelerometer signal were compared. 3) MP3/accelerometer acquisition units were used to log accelerometer signals from racehorses during extended training sessions. Mean absolute error of synchronisation between MP3 recorders was 10 samples per million (compared to mean number of samples, range 1-32 samples per million). Error accumulation showed a linear correlation with time. Features attributable to foot on and foot off were equally identifiable from the MP3 recorded signal over a range of equine gaits. Multiple MP3 recorders can be synchronised and used as a relatively cheap, robust, reliable and accurate logging system when combined with an accelerometer and external battery for the specific application of the measurement of stride timing variables across the range of equine gaits during field locomotion. Footfall timings can be used to identify intervals between the fore and hind contacts, the identification of diagonal advanced placement and to calculate stride timing variables (stance time, protraction

Nuclear Well Log Properties of Natural Gas Hydrate Reservoirs

Science.gov (United States)

Burchwell, A.; Cook, A.

2015-12-01

Characterizing gas hydrate in a reservoir typically involves a full suite of geophysical well logs. The most common method involves using resistivity measurements to quantify the decrease in electrically conductive water when replaced with gas hydrate. Compressional velocity measurements are also used because the gas hydrate significantly strengthens the moduli of the sediment. At many gas hydrate sites, nuclear well logs, which include the photoelectric effect, formation sigma, carbon/oxygen ratio and neutron porosity, are also collected but often not used. In fact, the nuclear response of a gas hydrate reservoir is not known. In this research we will focus on the nuclear log response in gas hydrate reservoirs at the Mallik Field at the Mackenzie Delta, Northwest Territories, Canada, and the Gas Hydrate Joint Industry Project Leg 2 sites in the northern Gulf of Mexico. Nuclear logs may add increased robustness to the investigation into the properties of gas hydrates and some types of logs may offer an opportunity to distinguish between gas hydrate and permafrost. For example, a true formation sigma log measures the thermal neutron capture cross section of a formation and pore constituents; it is especially sensitive to hydrogen and chlorine in the pore space. Chlorine has a high absorption potential, and is used to determine the amount of saline water within pore spaces. Gas hydrate offers a difference in elemental composition compared to water-saturated intervals. Thus, in permafrost areas, the carbon/oxygen ratio may vary between gas hydrate and permafrost, due to the increase of carbon in gas hydrate accumulations. At the Mallik site, we observe a hydrate-bearing sand (1085-1107 m) above a water-bearing sand (1107-1140 m), which was confirmed through core samples and mud gas analysis. We observe a decrease in the photoelectric absorption of ~0.5 barnes/e-, as well as an increase in the formation sigma readings of ~5 capture units in the water-bearing sand as

Logs of Paleoseismic Excavations Across the Central Range Fault, Trinidad

Science.gov (United States)

Crosby, Christopher J.; Prentice, Carol S.; Weber, John; Ragona, Daniel

2009-01-01

This publication makes available maps and trench logs associated with studies of the Central Range Fault, part of the South American-Caribbean plate boundary in Trinidad. Our studies were conducted in 2001 and 2002. We mapped geomorphic features indicative of active faulting along the right-lateral, Central Range Fault, part of the South American-Caribbean plate boundary in Trinidad. We excavated trenches at two sites, the Samlalsingh and Tabaquite sites. At the Samlalsingh site, sediments deposited after the most recent fault movement bury the fault, and the exact location of the fault was unknown until we exposed it in our excavations. At this site, we excavated a total of eleven trenches, six of which exposed the fault. The trenches exposed fluvial sediments deposited over a strath terrace developed on Miocene bedrock units. We cleaned the walls of the excavations, gridded the walls with either 1 m X 1 m or 1 m X 0.5 m nail and string grid, and logged the walls in detail at a scale of 1:20. Additionally, we described the different sedimentary units in the field, incorporating these descriptions into our trench logs. We mapped the locations of the trenches using a tape and compass. Our field logs were scanned, and unit contacts were traced in Adobe Illustrator. The final drafted logs of all the trenches are presented here, along with photographs showing important relations among faults and Holocene sedimentary deposits. Logs of south walls were reversed in Illustrator, so that all logs are drafted with the view direction to the north. We collected samples of various materials exposed in the trench walls, including charcoal samples for radiocarbon dating from both faulted and unfaulted deposits. The locations of all samples collected are shown on the logs. The ages of seventeen of the charcoal samples submitted for radiocarbon analysis at the University of Arizona Accelerator Mass Spectrometry Laboratory in Tucson, Ariz., are given in Table 1. Samples found in

Optimizing occupational exposure measurement strategies when estimating the log-scale arithmetic mean value--an example from the reinforced plastics industry.

Science.gov (United States)

Lampa, Erik G; Nilsson, Leif; Liljelind, Ingrid E; Bergdahl, Ingvar A

2006-06-01

When assessing occupational exposures, repeated measurements are in most cases required. Repeated measurements are more resource intensive than a single measurement, so careful planning of the measurement strategy is necessary to assure that resources are spent wisely. The optimal strategy depends on the objectives of the measurements. Here, two different models of random effects analysis of variance (ANOVA) are proposed for the optimization of measurement strategies by the minimization of the variance of the estimated log-transformed arithmetic mean value of a worker group, i.e. the strategies are optimized for precise estimation of that value. The first model is a one-way random effects ANOVA model. For that model it is shown that the best precision in the estimated mean value is always obtained by including as many workers as possible in the sample while restricting the number of replicates to two or at most three regardless of the size of the variance components. The second model introduces the 'shared temporal variation' which accounts for those random temporal fluctuations of the exposure that the workers have in common. It is shown for that model that the optimal sample allocation depends on the relative sizes of the between-worker component and the shared temporal component, so that if the between-worker component is larger than the shared temporal component more workers should be included in the sample and vice versa. The results are illustrated graphically with an example from the reinforced plastics industry. If there exists a shared temporal variation at a workplace, that variability needs to be accounted for in the sampling design and the more complex model is recommended.

LogScope

Science.gov (United States)

Havelund, Klaus; Smith, Margaret H.; Barringer, Howard; Groce, Alex

2012-01-01

LogScope is a software package for analyzing log files. The intended use is for offline post-processing of such logs, after the execution of the system under test. LogScope can, however, in principle, also be used to monitor systems online during their execution. Logs are checked against requirements formulated as monitors expressed in a rule-based specification language. This language has similarities to a state machine language, but is more expressive, for example, in its handling of data parameters. The specification language is user friendly, simple, and yet expressive enough for many practical scenarios. The LogScope software was initially developed to specifically assist in testing JPL s Mars Science Laboratory (MSL) flight software, but it is very generic in nature and can be applied to any application that produces some form of logging information (which almost any software does).

Effects of reduced-impact logging on fish assemblages in central Amazonia.

Science.gov (United States)

Dias, Murilo S; Magnusson, William E; Zuanon, Jansen

2010-02-01

In Amazonia reduced-impact logging, which is meant to reduce environmental disturbance by controlling stem-fall directions and minimizing construction of access roads, has been applied to large areas containing thousands of streams. We investigated the effects of reduced-impact logging on environmental variables and the composition of fish in forest streams in a commercial logging concession in central Amazonia, Amazonas State, Brazil. To evaluate short-term effects, we sampled 11 streams before and after logging in one harvest area. We evaluated medium-term effects by comparing streams in 11 harvest areas logged 1-8 years before the study with control streams in adjacent areas. Each sampling unit was a 50-m stream section. The tetras Pyrrhulina brevis and Hemigrammus cf. pretoensis had higher abundances in plots logged > or =3 years before compared with plots logged fish composition did not differ two months before and immediately after reduced-impact logging. Temperature and pH varied before and after logging, but those differences were compatible with normal seasonal variation. In the medium term, temperature and cover of logs were lower in logged plots. Differences in ordination scores on the basis of relative fish abundance between streams in control and logged areas changed with time since logging, mainly because some common species increased in abundance after logging. There was no evidence of species loss from the logging concession, but differences in log cover and ordination scores derived from relative abundance of fish species persisted even after 8 years. For Amazonian streams, reduced-impact logging appears to be a viable alternative to clear-cut practices, which severely affect aquatic communities. Nevertheless, detailed studies are necessary to evaluated subtle long-term effects.

Log-concave Probability Distributions: Theory and Statistical Testing

DEFF Research Database (Denmark)

An, Mark Yuing

1996-01-01

This paper studies the broad class of log-concave probability distributions that arise in economics of uncertainty and information. For univariate, continuous, and log-concave random variables we prove useful properties without imposing the differentiability of density functions. Discrete...... and multivariate distributions are also discussed. We propose simple non-parametric testing procedures for log-concavity. The test statistics are constructed to test one of the two implicati ons of log-concavity: increasing hazard rates and new-is-better-than-used (NBU) property. The test for increasing hazard...... rates are based on normalized spacing of the sample order statistics. The tests for NBU property fall into the category of Hoeffding's U-statistics...

Automated mineralogical logging of coal and coal measure core

Energy Technology Data Exchange (ETDEWEB)

Stephen Fraser; Joan Esterle; Colin Ward; Ruth Henwood; Peter Mason; Jon Huntington; Phil Connor; Reneta Sliwa; Dave Coward; Lew Whitbourn [CSIRO Exploration & Mining (Australia)

2006-06-15

A mineralogical core logging system based on spectral reflectance (HyLogger{trademark}) has been used to detect and quantify mineralogies in coal and coal measure sediments. The HyLogger{trademark} system, as tested, operates in the visible-to-shortwave infrared spectral region, where iron oxides, sulphates, hydroxyl-bearing and carbonate minerals have characteristic spectral responses. Specialized software assists with mineral identification and data display. Three Phases of activity were undertaken. In Phase I, carbonates (siderite, ankerite, calcite) and clays (halloysite, dickite) were successfully detected and mapped in coal. Repeat measurements taken from one of the cores after three months demonstrated the reproducibility of the spectral approach, with some spectral differences being attributed to variations in moisture content and oxidation. Also, investigated was HyLogger{trademark} ability to create a 'brightness-profile' on coal materials, and these results were encouraging. In Phase II, geotechnically significant smectitic clays (montmorillonite) were detected and mapped in cores of clastic roof and floor materials. Such knowledge would be useful for mine planning and design purposes. In Phase III, our attempts at determining whether phosphorus-bearing minerals such as apatite could be spectrally detected were less than conclusive. A spectral index could only be created for apatite, and the relationships between the spectrally-derived apatite-index, the XRD results and the analytically-derived phosphorus measurements were ambiguous.

A history of nuclear well logging in the oil industry

International Nuclear Information System (INIS)

Tittle, C.W.

1989-01-01

Spurred by an interest in logging through steel casing γ-ray logging began in the late 1930s followed soon by neutron logging for porosity. These were the first two nuclear well logs. Gamma-gamma density logging was developed during the 1950s. Pulsed neutron lifetime logging appeared in the 1960s; the slim tools came in the early 1970s. Developments since then have included dual detector devices of several types which offered improved measurements or interpretation, γ-ray spectrometry logging (natural and neutron-induced) which identifies certain chemical elements, induced radioactivity logging, and the photoelectric absorption log, which, combined with the density log in a single tool, is known as litho-density logging. A combination of several γ-ray spectrometers in one tool, designed to determine 10 formation elements, was recently introduced, and a new neutron porosity tool measuring epithermal neutron die-away time has been developed. Digital transmission of logging data was a step forward in about 1975. Also, log interpretation techniques have greatly expanded since the advent of digital computers, and the microcomputer has had a distinct impact. It is now practical and economical to do iterative analysis on a suite of logs to obtain an optimum overall interpretation. (author)

Rapid estimation of aquifer salinity structure from oil and gas geophysical logs

Science.gov (United States)

Shimabukuro, D.; Stephens, M.; Ducart, A.; Skinner, S. M.

2016-12-01

We describe a workflow for creating aquifer salinity maps using Archie's equation for areas that have geophysical data from oil and gas wells. We apply this method in California, where geophysical logs are available in raster format from the Division of Oil, Gas, and Geothermal Resource (DOGGR) online archive. This method should be applicable to any region where geophysical logs are readily available. Much of the work is controlled by computer code, allowing salinity estimates for new areas to be rapidly generated. For a region of interest, the DOGGR online database is scraped for wells that were logged with multi-tool suites, such as the Platform Express or Triple Combination Logging Tools. Then, well construction metadata, such as measured depth, spud date, and well orientation, is attached. The resultant local database allows a weighted criteria selection of wells that are most likely to have the shallow resistivity, deep resistivity, and density porosity measurements necessary to calculate salinity over the longest depth interval. The algorithm can be adjusted for geophysical log availability for older well fields and density of sampling. Once priority wells are identified, a student researcher team uses Neuralog software to digitize the raster geophysical logs. Total dissolved solid (TDS) concentration is then calculated in clean, wet sand intervals using the resistivity-porosity method, a modified form of Archie's equation. These sand intervals are automatically selected using a combination of spontaneous potential and the difference in shallow resistivity and deep resistivity measurements. Gamma ray logs are not used because arkosic sands common in California make it difficult to distinguish sand and shale. Computer calculation allows easy adjustment of Archie's parameters. The result is a semi-continuous TDS profile for the wells of interest. These profiles are combined and contoured using standard 3-d visualization software to yield preliminary salinity

Dynamic Planar Convex Hull with Optimal Query Time and O(log n · log log n ) Update Time

DEFF Research Database (Denmark)

Brodal, Gerth Stølting; Jakob, Riko

2000-01-01

The dynamic maintenance of the convex hull of a set of points in the plane is one of the most important problems in computational geometry. We present a data structure supporting point insertions in amortized O(log n · log log log n) time, point deletions in amortized O(log n · log log n) time......, and various queries about the convex hull in optimal O(log n) worst-case time. The data structure requires O(n) space. Applications of the new dynamic convex hull data structure are improved deterministic algorithms for the k-level problem and the red-blue segment intersection problem where all red and all...

Log-binomial models: exploring failed convergence.

Science.gov (United States)

Williamson, Tyler; Eliasziw, Misha; Fick, Gordon Hilton

2013-12-13

Relative risk is a summary metric that is commonly used in epidemiological investigations. Increasingly, epidemiologists are using log-binomial models to study the impact of a set of predictor variables on a single binary outcome, as they naturally offer relative risks. However, standard statistical software may report failed convergence when attempting to fit log-binomial models in certain settings. The methods that have been proposed in the literature for dealing with failed convergence use approximate solutions to avoid the issue. This research looks directly at the log-likelihood function for the simplest log-binomial model where failed convergence has been observed, a model with a single linear predictor with three levels. The possible causes of failed convergence are explored and potential solutions are presented for some cases. Among the principal causes is a failure of the fitting algorithm to converge despite the log-likelihood function having a single finite maximum. Despite these limitations, log-binomial models are a viable option for epidemiologists wishing to describe the relationship between a set of predictors and a binary outcome where relative risk is the desired summary measure. Epidemiologists are encouraged to continue to use log-binomial models and advocate for improvements to the fitting algorithms to promote the widespread use of log-binomial models.

Ecological Factors Influencing Norway Spruce Regeneration on Nurse Logs in a Subalpine Virgin Forest

Directory of Open Access Journals (Sweden)

Sophie Stroheker

2018-03-01

Full Text Available Regeneration of Picea abies in high-elevation mountain forests often depends on the presence of coarse woody debris (CWD, as logs provide sites with more favorable conditions for spruce regeneration compared to the forest floor. However, there is little quantitative knowledge on the factors that are conducive to or hindering spruce establishment on CWD. We examined spruce regeneration on CWD by sampling 303 plots (50 cm × 50 cm each on 56 downed logs in a virgin forest in the Swiss Alps. Variables describing microsite conditions were measured, and fungi were isolated from wood samples. To investigate the relationship between the ecological factors and establishment success, two models were fitted with seedling and sapling density as response variables, respectively. Besides log diameter, the models identified different ecological factors as significant for seedling and sapling establishment, i.e., regeneration depends on different factors in different development stages. Seedling density depended on the type of rot, log inclination, and decay stage. Sapling density depended mainly on light availability, cover by bark and moss, the time of tree fall, and the distance between the log surface and the forest floor. A total of 22 polypore fungi were isolated from the wood samples, four of them being threatened species. White- and brown-rot fungi were found in all decay stages. The visual assessment of the type of rot in the field corresponded in only 15% of cases to the type of rot caused by the isolated fungi; hence caution is needed when making field assessments of rot types.

Cased-hole log analysis and reservoir performance monitoring

CERN Document Server

Bateman, Richard M

2015-01-01

This book addresses vital issues, such as the evaluation of shale gas reservoirs and their production. Topics include the cased-hole logging environment, reservoir fluid properties; flow regimes; temperature, noise, cement bond, and pulsed neutron logging; and casing inspection. Production logging charts and tables are included in the appendices. The work serves as a comprehensive reference for production engineers with upstream E&P companies, well logging service company employees, university students, and petroleum industry training professionals. This book also: ·       Provides methods of conveying production logging tools along horizontal well segments as well as measurements of formation electrical resistivity through casing ·       Covers new information on fluid flow characteristics in inclined pipe and provides new and improved nuclear tool measurements in cased wells ·       Includes updates on cased-hole wireline formation testing  

REST: a computer system for estimating logging residue by using the line-intersect method

Science.gov (United States)

A. Jeff Martin

1975-01-01

A computer program was designed to accept logging-residue measurements obtained by line-intersect sampling and transform them into summaries useful for the land manager. The features of the program, along with inputs and outputs, are briefly described, with a note on machine compatibility.

Hardwood log grades and lumber grade yields for factory lumber logs

Science.gov (United States)

Leland F. Hanks; Glenn L. Gammon; Robert L. Brisbin; Everette D. Rast

1980-01-01

The USDA Forest Service Standard Grades for Hardwood Factory Lumber Logs are described, and lumber grade yields for 16 species and 2 species groups are presented by log grade and log diameter. The grades enable foresters, log buyers, and log sellers to select and grade those log suitable for conversion into standard factory grade lumber. By using the apropriate lumber...

Pulsed neutron uranium borehole logging with prompt fission neutrons

International Nuclear Information System (INIS)

Bivens, H.M.; Smith, G.W.; Jensen, D.H.

1976-01-01

The gross count natural gamma log normally used for uranium borehole logging is seriously affected by disequilibrium. Methods for the direct measurement of uranium, such as neutron logging, which are not affected by disequilibrium have been the object of considerable effort in recent years. This paper describes a logging system for uranium which uses a small accelerator to generate pulses of 14 MeV neutrons to detect and assay uranium by the measurement of prompt fission neutrons in the epithermal energy range. After an initial feasibility study, a prototype logging probe was built for field evaluation which began in January 1976. Physical and operational characteristics of the prototype probe, the neutron tube-transformer assembly, and the neutron tube are described. In logging operations, only the epithermal prompt fission neutrons detected between 250 microseconds to 2500 microseconds following the excitation neutron pulse are counted. Comparison of corrected neutron logs with the conventional gross count natural gamma logs and the chemical assays of cores from boreholes are shown. The results obtained with this neutron probe clearly demonstrate its advantages over the gross count natural gamma log, although at this time the accuracy of the neutron log assay is not satisfactory under some conditions. The necessary correction factors for various borehole and formation parameters are being determined and, when applied, should improve the assay accuracy

Logging Concessions Enable Illegal Logging Crisis in the Peruvian Amazon

OpenAIRE

Finer, Matt; Jenkins, Clinton N.; Sky, Melissa A. Blue; Pine, Justin

2014-01-01

The Peruvian Amazon is an important arena in global efforts to promote sustainable logging in the tropics. Despite recent efforts to achieve sustainability, such as provisions in the US?Peru Trade Promotion Agreement, illegal logging continues to plague the region. We present evidence that Peru's legal logging concession system is enabling the widespread illegal logging via the regulatory documents designed to ensure sustainable logging. Analyzing official government data, we found that 68.3%...

Well logging with natural gamma radiation

International Nuclear Information System (INIS)

Ellis, D.V.

1983-01-01

An invention is described for use in natural gamma radiation well logging in which measurements taken in a borehole are used in the search for valuable underground resources such as oil or gas. The invention comprises deriving a log of natural gamma radiation detected in selected energy windows for a selected borehole depth interval and converting it into a log of the selected subsurface materials, e.g. Th, U, K. This log is corrected for the effects of 1) either a gamma ray emitter in the borehole fluid, e.g. potassium salts and/or 2) a gamma ray attenuator in the borehole fluid, e.g. a strong attenuator such as barite and/or hematite. The Th, U, K log is particularly useful in the exploration of oil and gas resources since the Th, U, K concentrations are a good indication as to the presence, type and volume of shale and clay in the formations surrounding the borehole. (U.K.)

Regeneration of five commercially-valuable tree species after experimental logging in an Amazonian forest

Directory of Open Access Journals (Sweden)

Lima Albertina Pimentel

2002-01-01

Full Text Available This study investigated the regeneration variation of five commercially valuable tree species in relation to different intensities of felling in fourteen 4-ha plots in an area under experimental forest management. This experiment was carried out in a typical Amazonian tropical forest sample on "terra-firme," in Manaus (AM. Plots were logged 7 and 8 years (1987 and 1988, or 3 years (1993 before the study. All trees with height greater than 2 m, and diameter at breast height (DBH smaller than 10 cm were measured. Only Aniba hostmanniana, Ocotea aciphylla, Licaria pachycarpa, Eschweilera coriacea and Goupia glabra were sufficiently common for individual analyses. These species have high timber values in the local market. Eight years after logging, the species responded differently to logging intensities. The numbers of individuals of Goupia glabra and Aniba hostmanniana were positively related to the intensity of logging, while Ocotea aciphylla, Licaria pachycarpa, and Eschweilera coriacea showed no statistically significant response. In the most recently (1993 logged areas, Goupia glabra and Aniba hostmanniana had higher numbers of individuals than the control plots.

Well-logging method using well-logging tools run through a drill stem test string for determining in-situ change in formation water saturation values

International Nuclear Information System (INIS)

Fertl, W.H.

1975-01-01

A logging tool (pulsed neutron or neutron-gamma ray) whose response indicates formation water saturation value, is run through an opening extending through a portion of a drill stem test string. A sample portion of the formation fluid in the zone of interest is removed and another logging run is made. The differences between the plots of the two logging runs indicate the formation potential productivity in the zone of interest

Numerical simulation of responses for cased-hole density logging

International Nuclear Information System (INIS)

Wu, Wensheng; Fu, Yaping; Niu, Wei

2013-01-01

Stabilizing or stimulating oil production in old oil fields requires density logging in cased holes where open-hole logging data are either missing or of bad quality. However, measured values from cased-hole density logging are more severely influenced by factors such as fluid, casing, cement sheath and the outer diameter of the open-hole well compared with those from open-hole logging. To correctly apply the cased-hole formation density logging data, one must eliminate these influences on the measured values and study the characteristics of how the cased-hole density logging instrument responds to these factors. In this paper, a Monte Carlo numerical simulation technique was used to calculate the responses of the far detector of a cased-hole density logging instrument to in-hole fluid, casing wall thickness, cement sheath density and the formation and thus to obtain influence rules and response coefficients. The obtained response of the detector is a function of in-hole liquid, casing wall thickness, the casing's outer diameter, cement sheath density, open-hole well diameter and formation density. The ratio of the counting rate of the detector in the calibration well to that in the measurement well was used to get a fairly simple detector response equation and the coefficients in the equation are easy to acquire. These provide a new way of calculating cased-hole density through forward modelling methods. (paper)

Problems of calibrating measuring instruments for selective gamma-gamma logging

International Nuclear Information System (INIS)

Daniel, J.; Smolarova, H.

1977-01-01

Quantitative determination of copper content in the Novoveska Huta chalcopyrite deposit is described using selective gamma-gamma logging. Factors influencing the calibration quality are discussed. (author)

http Log Analysis

DEFF Research Database (Denmark)

Bøving, Kristian Billeskov; Simonsen, Jesper

2004-01-01

This article documents how log analysis can inform qualitative studies concerning the usage of web-based information systems (WIS). No prior research has used http log files as data to study collaboration between multiple users in organisational settings. We investigate how to perform http log...... analysis; what http log analysis says about the nature of collaborative WIS use; and how results from http log analysis may support other data collection methods such as surveys, interviews, and observation. The analysis of log files initially lends itself to research designs, which serve to test...... hypotheses using a quantitative methodology. We show that http log analysis can also be valuable in qualitative research such as case studies. The results from http log analysis can be triangulated with other data sources and for example serve as a means of supporting the interpretation of interview data...

Intelligent approaches for the synthesis of petrophysical logs

International Nuclear Information System (INIS)

Rezaee, M Reza; Kadkhodaie-Ilkhchi, Ali; Alizadeh, Pooya Mohammad

2008-01-01

Log data are of prime importance in acquiring petrophysical data from hydrocarbon reservoirs. Reliable log analysis in a hydrocarbon reservoir requires a complete set of logs. For many reasons, such as incomplete logging in old wells, destruction of logs due to inappropriate data storage and measurement errors due to problems with logging apparatus or hole conditions, log suites are either incomplete or unreliable. In this study, fuzzy logic and artificial neural networks were used as intelligent tools to synthesize petrophysical logs including neutron, density, sonic and deep resistivity. The petrophysical data from two wells were used for constructing intelligent models in the Fahlian limestone reservoir, Southern Iran. A third well from the field was used to evaluate the reliability of the models. The results showed that fuzzy logic and artificial neural networks were successful in synthesizing wireline logs. The combination of the results obtained from fuzzy logic and neural networks in a simple averaging committee machine (CM) showed a significant improvement in the accuracy of the estimations. This committee machine performed better than fuzzy logic or the neural network model in the problem of estimating petrophysical properties from well logs

A new measurement-while-drilling gamma ray log calibrator

International Nuclear Information System (INIS)

Meisner, J.; Brooks, A.; Wisniewski, W.

1985-01-01

Many of the present methods of calibration for both wireline and MWD gamma ray detectors use a point source at a fixed distance from the detector. MWD calibration errors are introduced from scattering effects, from spectral differences, from position sensitivity and form lack of cylindrical geometry. A new method has been developed at Exploration Logging INc. (EXLOG) that eliminates these errors. The method uses a wrap-around or annular calibrator, referenced to the University of Houston gamma ray API pit. The new calibrator is designed to simulate the API pit's gamma ray emission spectrum with a finite amount of natural source material in the annular shape. Because of the thickness of steel between the MWD gamma ray detector and the formation, there is theoretical necessity for spectral matching. A simple theoretical approach was used to calibrate the new calibrator. Spectral matching allows a closer approximation to wireline logs and makes it possible to estimate the relative spectral content of a formation

Log quality enhancement: A systematic assessment of logging company wellsite performance and log quality

International Nuclear Information System (INIS)

Farnan, R.A.; Mc Hattie, C.M.

1984-01-01

To improve the monitoring of logging company performance, computer programs were developed to assess information en masse from log quality check lists completed on wellsite by the service company engineer and Phillips representative. A study of all logging jobs performed by different service companies for Phillips in Oklahoma (panhandle excepted) during 1982 enabled several pertinent and beneficial interpretations to be made. Company A provided the best tool and crew service. Company B incurred an excessive amount of lost time related to tool failure, in particular the neutron-density tool combination. Company C, although used only three times, incurred no lost time. With a reasonable data base valid conclusions were made pertaining, for example, to repeated tool malfunctions. The actual logs were then assessed for quality

Exploration and grade control neutron logging

International Nuclear Information System (INIS)

Eisler, P.L.

1982-01-01

Techniques used in neutron logging in boreholes are discussed. They include the application of neutron probes to porosity measurements, to lithological determinations based on macroscopic cross-section measurements and measurements of the concentration of chemical constituents in rocks and ores

Turbidity Responses from Timber Harvesting, Wildfire, and Post-Fire Logging in the Battle Creek Watershed, Northern California.

Science.gov (United States)

Lewis, Jack; Rhodes, Jonathan J; Bradley, Curtis

2018-04-11

The Battle Creek watershed in northern California was historically important for its Chinook salmon populations, now at remnant levels due to land and water uses. Privately owned portions of the watershed are managed primarily for timber production, which has intensified since 1998, when clearcutting became widespread. Turbidity has been monitored by citizen volunteers at 13 locations in the watershed. Approximately 2000 grab samples were collected in the 5-year analysis period as harvesting progressed, a severe wildfire burned 11,200 ha, and most of the burned area was salvage logged. The data reveal strong associations of turbidity with the proportion of area harvested in watersheds draining to the measurement sites. Turbidity increased significantly over the measurement period in 10 watersheds and decreased at one. Some of these increases may be due to the influence of wildfire, logging roads and haul roads. However, turbidity continued trending upwards in six burned watersheds that were logged after the fire, while decreasing or remaining the same in two that escaped the fire and post-fire logging. Unusually high turbidity measurements (more than seven times the average value for a given flow condition) were very rare (0.0% of measurements) before the fire but began to appear in the first year after the fire (5.0% of measurements) and were most frequent (11.6% of measurements) in the first 9 months after salvage logging. Results suggest that harvesting contributes to road erosion and that current management practices do not fully protect water quality.

Screening efficacy of a simplified logMAR chart

Directory of Open Access Journals (Sweden)

Naganathan Muthuramalingam

2016-04-01

Aim: This study evaluates the efficacy of a simplified logMAR chart, designed for VA testing over the conventional Snellen chart, in a school-based vision-screening programme. Methods: We designed a simplified logMAR chart by employing the principles of the Early Treatment Diabetic Retinopathy Study (ETDRS chart in terms of logarithmic letter size progression, inter-letter spacing, and inter-line spacing. Once the simplified logMAR chart was validated by students in the Elite school vision-screening programme, we set out to test the chart in 88 primary and middle schools in the Tiruporur block of Kancheepuram district in Tamil Nadu. One school teacher in each school was trained to screen a cross-sectional population of 10 354 primary and secondary school children (girls: 5488; boys: 4866 for VA deficits using a new, simplified logMAR algorithm. An experienced paediatric optometrist was recruited to validate the screening methods and technique used by the teachers to collect the data. Results: The optometrist screened a subset of 1300 school children from the total sample. The optometrist provided the professional insights needed to validate the clinical efficacy of the simplified logMAR algorithm and verified the reliability of the data collected by the teachers. The mean age of children sampled for validation was 8.6 years (range: 9–14 years. The sensitivity and the specificity of the simplified logMAR chart when compared to the standard logMAR chart were found to be 95% and 98%, respectively. Kappa value was 0.97. Sensitivity of the teachers’ screening was 66.63% (95% confidence interval [CI]: 52.73–77.02 and the specificity was 98.33% (95% CI: 97.49–98.95. Testing of VA was done under substandard illumination levels in 87% of the population. A total of 10 354 children were screened, 425 of whom were found to have some form of visual and/or ocular defect that was identified by the teacher or optometrist. Conclusion: The simplified logMAR testing algorithm

Mechanics of log calibration

International Nuclear Information System (INIS)

Waller, W.C.; Cram, M.E.; Hall, J.E.

1975-01-01

For any measurement to have meaning, it must be related to generally accepted standard units by a valid and specified system of comparison. To calibrate well-logging tools, sensing systems are designed which produce consistent and repeatable indications over the range for which the tool was intended. The basics of calibration theory, procedures, and calibration record presentations are reviewed. Calibrations for induction, electrical, radioactivity, and sonic logging tools will be discussed. The authors' intent is to provide an understanding of the sources of errors, of the way errors are minimized in the calibration process, and of the significance of changes in recorded calibration data

Pinpointing water entries using pulsed neutron and Production logging tools

International Nuclear Information System (INIS)

Mukerji, P.; Oluwa, J.

2003-01-01

A successful work over requires a comprehensive understanding of fluid entries into the wellbore and fluid contact movement in the reservoir. Such information can be obtained by a combination of production logs and saturation-monitoring measurements. The ability to combine pulsed neutron and production logging tools provides the operator with better diagnostics for identifying candidates for remedial actions and greatly increases the possibility of a successful well intervention. Advances in pulsed neutron spectroscopy tools have improved the accuracy and precision of measured carbon/oxygen ratios. Some of the improvements in accuracy and precision have resulted from better tool characterization in a wider variety of logging environments in the calibration facility and new spectral standards. Coincident with the advances in pulsed neutron spectroscopy has been the development of production logging measurements run on a platform common. We will show how the application of pulsed neutron and production logs can optimize subsequent well intervention to reduce water production and/or increase oil production

Log N-log S in inconclusive

Science.gov (United States)

Klebesadel, R. W.; Fenimore, E. E.; Laros, J.

1983-01-01

The log N-log S data acquired by the Pioneer Venus Orbiter Gamma Burst Detector (PVO) are presented and compared to similar data from the Soviet KONUS experiment. Although the PVO data are consistent with and suggestive of a -3/2 power law distribution, the results are not adequate at this state of observations to differentiate between a -3/2 and a -1 power law slope.

Construction and validation of a Tamil logMAR chart.

Science.gov (United States)

Varadharajan, Srinivasa; Srinivasan, Krithica; Kumaresan, Brindha

2009-09-01

To design, construct and validate a new Tamil logMAR visual acuity chart based on current recommendations. Ten Tamil letters of equal legibility were identified experimentally and were used in the chart. Two charts, one internally illuminated and one externally illuminated, were constructed for testing at 4 m distance. The repeatability of the two charts was tested. For validation, the two charts were compared with a standard English logMAR chart (ETDRS). When compared to the ETDRS chart, a difference of 0.06 +/- 0.07 and 0.07 +/- 0.07 logMAR was found for the internally and externally illuminated charts respectively. Limits of agreement between the internally illuminated Tamil logMAR chart and ETDRS chart were found to be (-0.08, 0.19), and (-0.07, 0.20) for the externally illuminated chart. The test - retest results showed a difference of 0.02 +/- 0.04 and 0.02 +/- 0.06 logMAR for the internally and externally illuminated charts respectively. Limits of agreement for repeated measurements for the internally illuminated Tamil logMAR chart were found to be (-0.06, 0.10), and (-0.10, 0.14) for the externally illuminated chart. The newly constructed Tamil logMAR charts have good repeatability. The difference in visual acuity scores between the newly constructed Tamil logMAR chart and the standard English logMAR chart was within acceptable limits. This new chart can be used for measuring visual acuity in the literate Tamil population.

Measurement of stiffness of standing trees and felled logs using acoustics: A review.

Science.gov (United States)

Legg, Mathew; Bradley, Stuart

2016-02-01

This paper provides a review on the use of acoustics to measure stiffness of standing trees, stems, and logs. An outline is given of the properties of wood and how these are related to stiffness and acoustic velocity throughout the tree. Factors are described that influence the speed of sound in wood, including the different types of acoustic waves which propagate in tree stems and lumber. Acoustic tools and techniques that have been used to measure the stiffness of wood are reviewed. The reasons for a systematic difference between direct and acoustic measurements of stiffness for standing trees, and methods for correction, are discussed. Other techniques, which have been used in addition to acoustics to try to improve stiffness measurements, are also briefly described. Also reviewed are studies which have used acoustic tools to investigate factors that influence the stiffness of trees. These factors include different silvicultural practices, geographic and environmental conditions, and genetics.

Applicability estimation of flowmeter logging for detecting hydraulic pass

International Nuclear Information System (INIS)

Miyakawa, Kimio; Tanaka, Yasuji; Tanaka, Kazuhiro

1997-01-01

Estimation of the hydraulic pass governing hydrogeological structure contributes significantly to the siting HLW repository. Flowmeter logging can detect hydraulic passes by measuring vertical flow velocity of groundwater in the borehole. We reviewed application of this logging in situ. The hydraulic pass was detected with combination of ambient flow logging, with pumping and/or injecting induced flow logging. This application showed that the flowmeter logging detected hydraulic passes conveniently and accurately compared with other hydraulic tests. Hydraulic conductivity by using flowmeter logging was assessed above 10 -6 m/sec and within one order from comparison with injection packer tests. We suggest that appropriate application of the flowmeter logging for the siting is conducted before hydraulic tests because test sections and monitoring sections are decided rationally for procurement of quantitative hydraulic data. (author)

Aespoe Hard Rock Laboratory. BIPS logging in borehole KAS09

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, Jaana; Gustafsson, Christer (Malaa Geoscience AB (Sweden))

2010-01-15

This report includes the data gained in BIPS logging performed at the Aespoe Hard Rock Laboratory. The logging operation presented here includes BIPS logging in the core drilled borehole KAS09. The objective for the BIPS logging was to observe the condition of KAS09 in order to restore the borehole in the hydrogeological monitoring programme.All measurements were conducted by Malaa Geoscience AB on October 9th 2009. The objective of the BIPS logging is to achieve information of the borehole including occurrence of rock types as well as determination of fracture distribution and orientation. This report describes the equipment used as well as the measurement procedures and data gained. For the BIPS survey, the result is presented as images. The basic conditions of the BIPS logging for geological mapping and orientation of structures are satisfying for borehole KAS09, although induced affects from the drilling on the borehole walls limit the visibility

Aespoe Hard Rock Laboratory. BIPS logging in borehole KAS09

International Nuclear Information System (INIS)

Gustafsson, Jaana; Gustafsson, Christer

2010-01-01

This report includes the data gained in BIPS logging performed at the Aespoe Hard Rock Laboratory. The logging operation presented here includes BIPS logging in the core drilled borehole KAS09. The objective for the BIPS logging was to observe the condition of KAS09 in order to restore the borehole in the hydrogeological monitoring programme.All measurements were conducted by Malaa Geoscience AB on October 9th 2009. The objective of the BIPS logging is to achieve information of the borehole including occurrence of rock types as well as determination of fracture distribution and orientation. This report describes the equipment used as well as the measurement procedures and data gained. For the BIPS survey, the result is presented as images. The basic conditions of the BIPS logging for geological mapping and orientation of structures are satisfying for borehole KAS09, although induced affects from the drilling on the borehole walls limit the visibility

The pdk-100 enhances interpretation capabilities for pulsed neutron capture logs

International Nuclear Information System (INIS)

Randall, R.R.; Oliver, D.W.; Ferti, W.H.

1986-01-01

The PDK-100 is a new pulsed neutron logging system designed to measure Sigma (Σ), the macroscopic thermal neutron capture cross section. In addition to determining Σ, the system provides logging curves which are a measure of formation porosity and which furnish information concerning borehole conditions. This paper reviews the principles of operation of the PDK-100, and presents examples which illustrate the utility of the logging system. In addition, the progress of investigations into new parameters which can be derived with pulsed neutron logging data will be reported

Analysis of RIA standard curve by log-logistic and cubic log-logit models

International Nuclear Information System (INIS)

Yamada, Hideo; Kuroda, Akira; Yatabe, Tami; Inaba, Taeko; Chiba, Kazuo

1981-01-01

In order to improve goodness-of-fit in RIA standard analysis, programs for computing log-logistic and cubic log-logit were written in BASIC using personal computer P-6060 (Olivetti). Iterative least square method of Taylor series was applied for non-linear estimation of logistic and log-logistic. Hear ''log-logistic'' represents Y = (a - d)/(1 + (log(X)/c)sup(b)) + d As weights either 1, 1/var(Y) or 1/σ 2 were used in logistic or log-logistic and either Y 2 (1 - Y) 2 , Y 2 (1 - Y) 2 /var(Y), or Y 2 (1 - Y) 2 /σ 2 were used in quadratic or cubic log-logit. The term var(Y) represents squares of pure error and σ 2 represents estimated variance calculated using a following equation log(σ 2 + 1) = log(A) + J log(y). As indicators for goodness-of-fit, MSL/S sub(e)sup(2), CMD% and WRV (see text) were used. Better regression was obtained in case of alpha-fetoprotein by log-logistic than by logistic. Cortisol standard curve was much better fitted with cubic log-logit than quadratic log-logit. Predicted precision of AFP standard curve was below 5% in log-logistic in stead of 8% in logistic analysis. Predicted precision obtained using cubic log-logit was about five times lower than that with quadratic log-logit. Importance of selecting good models in RIA data processing was stressed in conjunction with intrinsic precision of radioimmunoassay system indicated by predicted precision. (author)

Monte Carlo Numerical Models for Nuclear Logging Applications

Directory of Open Access Journals (Sweden)

Fusheng Li

2012-06-01

Full Text Available Nuclear logging is one of most important logging services provided by many oil service companies. The main parameters of interest are formation porosity, bulk density, and natural radiation. Other services are also provided from using complex nuclear logging tools, such as formation lithology/mineralogy, etc. Some parameters can be measured by using neutron logging tools and some can only be measured by using a gamma ray tool. To understand the response of nuclear logging tools, the neutron transport/diffusion theory and photon diffusion theory are needed. Unfortunately, for most cases there are no analytical answers if complex tool geometry is involved. For many years, Monte Carlo numerical models have been used by nuclear scientists in the well logging industry to address these challenges. The models have been widely employed in the optimization of nuclear logging tool design, and the development of interpretation methods for nuclear logs. They have also been used to predict the response of nuclear logging systems for forward simulation problems. In this case, the system parameters including geometry, materials and nuclear sources, etc., are pre-defined and the transportation and interactions of nuclear particles (such as neutrons, photons and/or electrons in the regions of interest are simulated according to detailed nuclear physics theory and their nuclear cross-section data (probability of interacting. Then the deposited energies of particles entering the detectors are recorded and tallied and the tool responses to such a scenario are generated. A general-purpose code named Monte Carlo N– Particle (MCNP has been the industry-standard for some time. In this paper, we briefly introduce the fundamental principles of Monte Carlo numerical modeling and review the physics of MCNP. Some of the latest developments of Monte Carlo Models are also reviewed. A variety of examples are presented to illustrate the uses of Monte Carlo numerical models

The feasibility of well-logging measurements of arsenic levels using neutron-activation analysis

Science.gov (United States)

Oden, C.P.; Schweitzer, J.S.; McDowell, G.M.

2006-01-01

Arsenic is an extremely toxic metal, which poses a significant problem in many mining environments. Arsenic contamination is also a major problem in ground and surface waters. A feasibility study was conducted to determine if neutron-activation analysis is a practical method of measuring in situ arsenic levels. The response of hypothetical well-logging tools to arsenic was simulated using a readily available Monte Carlo simulation code (MCNP). Simulations were made for probes with both hyperpure germanium (HPGe) and bismuth germanate (BGO) detectors using accelerator and isotopic neutron sources. Both sources produce similar results; however, the BGO detector is much more susceptible to spectral interference than the HPGe detector. Spectral interference from copper can preclude low-level arsenic measurements when using the BGO detector. Results show that a borehole probe could be built that would measure arsenic concentrations of 100 ppm by weight to an uncertainty of 50 ppm in about 15 min. ?? 2006 Elsevier Ltd. All rights reserved.

Formation evaluation in Devonian shale through application of new core and log analysis methods

International Nuclear Information System (INIS)

Luffel, D.L.; Guidry, F.K.

1990-01-01

In the Devonian shale of the Appalachian Basin all porosity in excess of about 2.5 percent is generally occupied by free hydrocarbons, which is mostly gas, based on results of new core and log analysis methods. In this study, sponsored by the Gas Research Institute, reservoir porosities averaged about 5 percent and free gas content averaged about 2 percent by bulk volume, based on analyses on 519 feet of conventional core in four wells. In this source-rich Devonian shale, which also provides the reservoir storage, the rock everywhere appears to be at connate, or irreducible, water saturation corresponding to two or three percent of bulk volume. This became evident when applying the new core and log analysis methods, along with a new plotting method relating bulk volume of pore fluids to porosity. This plotting method has proved to be a valuable tool: it provides useful insight on the fluid distribution present in the reservoir, it provides a clear idea of porosity required to store free hydrocarbons, it leads to a method of linking formation factor to porosity, and it provides a good quality control method to monitor core and log analysis results. In the Devonian shale an important part of the formation evaluation is to determine the amount of kerogen, since this appears as hydrocarbon-filled porosity to conventional logs. In this study Total Organic Carbon and pyrolysis analyses were made on 93 core samples from four wells. Based on these data a new method was used to drive volumetric kerogen and free oil content, and kerogen was found to range up to 26 percent by volume. A good correlation was subsequently developed to derive kerogen from the uranium response of the spectral gamma ray log. Another important result of this study is the measurement of formation water salinity directly on core samples. Results on 50 measurements in the four study wells ranged from 19,000 to 220,000 ppm NaCl

Modeling the dielectric logging tool at high frequency

International Nuclear Information System (INIS)

Chew, W.C.

1987-01-01

The high frequency dielectric logging tool has been used widely in electromagnetic well logging, because by measuring the dielectric constant at high frequencies (1 GHz), the water saturation of rocks could be known without measuring the water salinity in the rocks. As such, it could be used to delineate fresh water bearing zones, as the dielectric constant of fresh water is much higher than that of oil while they may have the same resistivity. The authors present a computer model, though electromagnetic field analysis, the response of such a measurement tool in a well logging environment. As the measurement is performed at high frequency, usually with small separation between the transmitter and receivers, some small geological features could be measured by such a tool. They use the computer model to study the behavior of such a tool across geological bed boundaries, and also across thin geological beds. Such a study could be very useful in understanding the limitation on the resolution of the tool. Furthermore, they could study the standoff effect and the depth of investigation of such a tool. This could delineate the range of usefulness of the measurement

A fast simulation method for the Log-normal sum distribution using a hazard rate twisting technique

KAUST Repository

Rached, Nadhir B.

2015-06-08

The probability density function of the sum of Log-normally distributed random variables (RVs) is a well-known challenging problem. For instance, an analytical closed-form expression of the Log-normal sum distribution does not exist and is still an open problem. A crude Monte Carlo (MC) simulation is of course an alternative approach. However, this technique is computationally expensive especially when dealing with rare events (i.e. events with very small probabilities). Importance Sampling (IS) is a method that improves the computational efficiency of MC simulations. In this paper, we develop an efficient IS method for the estimation of the Complementary Cumulative Distribution Function (CCDF) of the sum of independent and not identically distributed Log-normal RVs. This technique is based on constructing a sampling distribution via twisting the hazard rate of the original probability measure. Our main result is that the estimation of the CCDF is asymptotically optimal using the proposed IS hazard rate twisting technique. We also offer some selected simulation results illustrating the considerable computational gain of the IS method compared to the naive MC simulation approach.

A fast simulation method for the Log-normal sum distribution using a hazard rate twisting technique

KAUST Repository

Rached, Nadhir B.; Benkhelifa, Fatma; Alouini, Mohamed-Slim; Tempone, Raul

2015-01-01

The probability density function of the sum of Log-normally distributed random variables (RVs) is a well-known challenging problem. For instance, an analytical closed-form expression of the Log-normal sum distribution does not exist and is still an open problem. A crude Monte Carlo (MC) simulation is of course an alternative approach. However, this technique is computationally expensive especially when dealing with rare events (i.e. events with very small probabilities). Importance Sampling (IS) is a method that improves the computational efficiency of MC simulations. In this paper, we develop an efficient IS method for the estimation of the Complementary Cumulative Distribution Function (CCDF) of the sum of independent and not identically distributed Log-normal RVs. This technique is based on constructing a sampling distribution via twisting the hazard rate of the original probability measure. Our main result is that the estimation of the CCDF is asymptotically optimal using the proposed IS hazard rate twisting technique. We also offer some selected simulation results illustrating the considerable computational gain of the IS method compared to the naive MC simulation approach.

Pulsed neutron generator for logging

International Nuclear Information System (INIS)

Thibideau, F.D.

1977-01-01

A pulsed neutron generator for uranium logging is described. This generator is one component of a prototype uranium logging probe which is being developed by SLA to detect, and assay, uranium by borehole logging. The logging method is based on the measurement of epithermal neutrons resulting from the prompt fissioning of uranium from a pulsed source of 17.6 MeV neutrons. An objective of the prototype probe was that its diameter not exceed 2.75 inches, which would allow its use in conventional rotary drill holes of 4.75-inch diameter. This restriction limited the generator to a maximum 2.375-inch diameter. The performance requirements for the neutron generator specified that it operate with a nominal output of 5 x 10 6 neutrons/pulse at up to 100 pulses/second for a one-hour period. The development of a neutron generator meeting the preliminary design goals was completed and two prototype models were delivered to SLA. These two generators have been used by SLA to log a number of boreholes in field evaluation of the probe. The results of the field evaluations have led to the recommendation of several changes to improve the probe's operation. Some of these changes will require additional development effort on the neutron generator. It is expected that this work will be performed during 1977. The design and operation of the first prototype neutron generators is described

Radiation transport methods for nuclear log assessment - an overview

International Nuclear Information System (INIS)

Badruzzaman, A.

1996-01-01

Methods of radiation transport have been applied to well-logging problems with nuclear sources since the early 1960s. Nuclear sondes are used in identifying rock compositions and fluid properties in reservoirs to predict the porosity and oil saturation. Early computational effort in nuclear logging used diffusion techniques. As computers became more powerful, deterministic transport methods and, finally, Monte Carlo methods were applied to solve these problems in three dimensions. Recently, the application has been extended to problems with a new generation of devices, including spectroscopic sondes that measure such quantities as the carbon/oxygen ratio to predict oil saturation and logging-while-drilling (LWD) sondes that take neutron and gamma measurements as they rotate in the borehole. These measurements present conditions that will be difficult to calibrate in the laboratory

Generalized localization for the double trigonometric Fourier series and the Walsh-Fourier series of functions in L log +L log + log +L

International Nuclear Information System (INIS)

Bloshanskaya, S K; Bloshanskii, I L; Roslova, T Y

1998-01-01

For an arbitrary open set Ω subset of I 2 =[0,1) 2 and an arbitrary function f element of L log + L log + log + L(I 2 ) such that f=0 on Ω the double Fourier series of f with respect to the trigonometric system Ψ=E and the Walsh-Paley system Ψ=W is shown to converge to zero (over rectangles) almost everywhere on Ω. Thus, it is proved that generalized localization almost everywhere holds on arbitrary open subsets of the square I 2 for the double trigonometric Fourier series and the Walsh-Fourier series of functions in the class L log + L log + log + L (in the case of summation over rectangles). It is also established that such localization breaks down on arbitrary sets that are not dense in I 2 , in the classes Φ Ψ (L)(I 2 ) for the orthonormal system Ψ=E and an arbitrary function such that Φ E (u)=o(u log + log + u) as u→∞ or for Φ W (u)=u( log + log + u) 1-ε , 0<ε<1

Applications of outcrop gamma-ray logging to field development and exploration

International Nuclear Information System (INIS)

Jordan, D.W.; Slatt, R.M.; Gillespie, R.H.; D'Agostino, A.E.; Scheihing, M.H.

1991-01-01

Gamma-ray logs of outcrops have been generated using two techniques. These techniques demonstrate the applicability of outcrop logging to better understand reservoir facies architecture and exploration type problems. The first logging technique employs the use of a standard logging truck and gamma-ray sonde. The truck is positioned near the top of the cliff face and the sonde is lowered to the bottom of the cliff. Gamma-ray counts are recorded as the sonde is raised at a constant rate. The second logging technique employs the use of a commercially available, hand-held, gamma-ray scintillometer. The tool measures total radiation at the outcrop. Equally-spaced measurements are made along the section and are displayed as a function of depth below a reference point. In this paper examples of gamma-ray logging experiments conducted on turbidities of the Jackfork Group (Pennsylvanian) in central and southern Arkansas are discussed, as are application of outcrop gamma-ray logging in the Long Beach Unit of Wilmington Oil Field, California, and Point Mugu (Santa Barbara Channel), California

Borehole logging

International Nuclear Information System (INIS)

Olsen, H.

1995-01-01

Numerous ground water investigations have been accomplished by means of borehole logging. Borehole logging can be applied to establish new water recovery wells, to control the existing water producing wells and source areas and to estimate ground water quality. (EG)

Analysis of log rate noise in Ontario's CANDU reactors

Energy Technology Data Exchange (ETDEWEB)

Hinds, H.W. [Dynamic Simulation and Analysis Corp., Deep River, Ontario (Canada); Banica, C.; Arguner, D. [Ontario Power Generation, Ajax, Ontario (Canada); Scharfenberg, R. [Bruce Power, Tiverton, Ontario (Canada)

2007-07-01

In the fall of 2003, the operators noticed that in the recently-refurbished Bruce A Shutdown System no. 1 (SDS1) the noise level in Log Rate signals were much larger than before. At the request of the Canadian Nuclear Safety Commission (CNSC), all Canadian CANDU reactors took action to characterize their Log Rate noise. Staff of the Inspection and Maintenance Services division of Ontario Power Generation (OPG) has collected high-speed high-accuracy noise data from nearly all 16 Ontario reactors, either as part of routine measurements before planned outages or as a dedicated noise recording. This paper gives the results of examining a suitable subset of this data, with respect to the characteristics and possible causes of Log Rate noise. The reactor and instrumentation design is different at each station: the locations of the moderator injection nozzles, the location of the ion chambers for each system, and the design of the Log Rate amplifiers. It was found that the Log noise (source of Log Rate noise) was much larger for those ion chambers in the path of the moderator injection nozzles, compared to those which were not in the path. This 'extra' Log noise would then be either attenuated or amplified depending on the transfer function (time constants) of the Log Rate amplifier. It was also observed that most of the Log and Log Rate noise is independent of any other signal measured. Although all CANDU reactors in Ontario have Log and Log Rate noise, the Bruce A SDS1 system has the largest amount of Log Rate noise, because (a) its SDS1 (and RRS) ion chambers are at the top of the reactor in the path of the moderator injection nozzles, and (b) its SDS1 Log Rate amplifiers have the smallest time constants. (author)

Logging Concessions Enable Illegal Logging Crisis in the Peruvian Amazon

Science.gov (United States)

Finer, Matt; Jenkins, Clinton N.; Sky, Melissa A. Blue; Pine, Justin

2014-04-01

The Peruvian Amazon is an important arena in global efforts to promote sustainable logging in the tropics. Despite recent efforts to achieve sustainability, such as provisions in the US-Peru Trade Promotion Agreement, illegal logging continues to plague the region. We present evidence that Peru's legal logging concession system is enabling the widespread illegal logging via the regulatory documents designed to ensure sustainable logging. Analyzing official government data, we found that 68.3% of all concessions supervised by authorities were suspected of major violations. Of the 609 total concessions, nearly 30% have been cancelled for violations and we expect this percentage to increase as investigations continue. Moreover, the nature of the violations indicate that the permits associated with legal concessions are used to harvest trees in unauthorized areas, thus threatening all forested areas. Many of the violations pertain to the illegal extraction of CITES-listed timber species outside authorized areas. These findings highlight the need for additional reforms.

Logging concessions enable illegal logging crisis in the Peruvian Amazon.

Science.gov (United States)

Finer, Matt; Jenkins, Clinton N; Sky, Melissa A Blue; Pine, Justin

2014-04-17

The Peruvian Amazon is an important arena in global efforts to promote sustainable logging in the tropics. Despite recent efforts to achieve sustainability, such as provisions in the US-Peru Trade Promotion Agreement, illegal logging continues to plague the region. We present evidence that Peru's legal logging concession system is enabling the widespread illegal logging via the regulatory documents designed to ensure sustainable logging. Analyzing official government data, we found that 68.3% of all concessions supervised by authorities were suspected of major violations. Of the 609 total concessions, nearly 30% have been cancelled for violations and we expect this percentage to increase as investigations continue. Moreover, the nature of the violations indicate that the permits associated with legal concessions are used to harvest trees in unauthorized areas, thus threatening all forested areas. Many of the violations pertain to the illegal extraction of CITES-listed timber species outside authorized areas. These findings highlight the need for additional reforms.

Bayesian Hierarchical Scale Mixtures of Log-Normal Models for Inference in Reliability with Stochastic Constraint

Directory of Open Access Journals (Sweden)

Hea-Jung Kim

2017-06-01

Full Text Available This paper develops Bayesian inference in reliability of a class of scale mixtures of log-normal failure time (SMLNFT models with stochastic (or uncertain constraint in their reliability measures. The class is comprehensive and includes existing failure time (FT models (such as log-normal, log-Cauchy, and log-logistic FT models as well as new models that are robust in terms of heavy-tailed FT observations. Since classical frequency approaches to reliability analysis based on the SMLNFT model with stochastic constraint are intractable, the Bayesian method is pursued utilizing a Markov chain Monte Carlo (MCMC sampling based approach. This paper introduces a two-stage maximum entropy (MaxEnt prior, which elicits a priori uncertain constraint and develops Bayesian hierarchical SMLNFT model by using the prior. The paper also proposes an MCMC method for Bayesian inference in the SMLNFT model reliability and calls attention to properties of the MaxEnt prior that are useful for method development. Finally, two data sets are used to illustrate how the proposed methodology works.

Gaseous radiocarbon measurements of small samples

International Nuclear Information System (INIS)

Ruff, M.; Szidat, S.; Gaeggeler, H.W.; Suter, M.; Synal, H.-A.; Wacker, L.

2010-01-01

Radiocarbon dating by means of accelerator mass spectrometry (AMS) is a well-established method for samples containing carbon in the milligram range. However, the measurement of small samples containing less than 50 μg carbon often fails. It is difficult to graphitise these samples and the preparation is prone to contamination. To avoid graphitisation, a solution can be the direct measurement of carbon dioxide. The MICADAS, the smallest accelerator for radiocarbon dating in Zurich, is equipped with a hybrid Cs sputter ion source. It allows the measurement of both, graphite targets and gaseous CO 2 samples, without any rebuilding. This work presents experiences dealing with small samples containing 1-40 μg carbon. 500 unknown samples of different environmental research fields have been measured yet. Most of the samples were measured with the gas ion source. These data are compared with earlier measurements of small graphite samples. The performance of the two different techniques is discussed and main contributions to the blank determined. An analysis of blank and standard data measured within years allowed a quantification of the contamination, which was found to be of the order of 55 ng and 750 ng carbon (50 pMC) for the gaseous and the graphite samples, respectively. For quality control, a number of certified standards were measured using the gas ion source to demonstrate reliability of the data.

Comparison of fine particle measurements from a direct-reading instrument and a gravimetric sampling method.

Science.gov (United States)

Kim, Jee Young; Magari, Shannon R; Herrick, Robert F; Smith, Thomas J; Christiani, David C

2004-11-01

Particulate air pollution, specifically the fine particle fraction (PM2.5), has been associated with increased cardiopulmonary morbidity and mortality in general population studies. Occupational exposure to fine particulate matter can exceed ambient levels by a large factor. Due to increased interest in the health effects of particulate matter, many particle sampling methods have been developed In this study, two such measurement methods were used simultaneously and compared. PM2.5 was sampled using a filter-based gravimetric sampling method and a direct-reading instrument, the TSI Inc. model 8520 DUSTTRAK aerosol monitor. Both sampling methods were used to determine the PM2.5 exposure in a group of boilermakers exposed to welding fumes and residual fuel oil ash. The geometric mean PM2.5 concentration was 0.30 mg/m3 (GSD 3.25) and 0.31 mg/m3 (GSD 2.90)from the DUSTTRAK and gravimetric method, respectively. The Spearman rank correlation coefficient for the gravimetric and DUSTTRAK PM2.5 concentrations was 0.68. Linear regression models indicated that log, DUSTTRAK PM2.5 concentrations significantly predicted loge gravimetric PM2.5 concentrations (p gravimetric PM2.5 concentrations was found to be modified by surrogate measures for seasonal variation and type of aerosol. PM2.5 measurements from the DUSTTRAK are well correlated and highly predictive of measurements from the gravimetric sampling method for the aerosols in these work environments. However, results from this study suggest that aerosol particle characteristics may affect the relationship between the gravimetric and DUSTTRAK PM2.5 measurements. Recalibration of the DUSTTRAK for the specific aerosol, as recommended by the manufacturer, may be necessary to produce valid measures of airborne particulate matter.

Laser scanning measurements on trees for logging harvesting operations.

Science.gov (United States)

Zheng, Yili; Liu, Jinhao; Wang, Dian; Yang, Ruixi

2012-01-01

Logging harvesters represent a set of high-performance modern forestry machinery, which can finish a series of continuous operations such as felling, delimbing, peeling, bucking and so forth with human intervention. It is found by experiment that during the process of the alignment of the harvesting head to capture the trunk, the operator needs a lot of observation, judgment and repeated operations, which lead to the time and fuel losses. In order to improve the operation efficiency and reduce the operating costs, the point clouds for standing trees are collected with a low-cost 2D laser scanner. A cluster extracting algorithm and filtering algorithm are used to classify each trunk from the point cloud. On the assumption that every cross section of the target trunk is approximate a standard circle and combining the information of an Attitude and Heading Reference System, the radii and center locations of the trunks in the scanning range are calculated by the Fletcher-Reeves conjugate gradient algorithm. The method is validated through experiments in an aspen forest, and the optimized calculation time consumption is compared with the previous work of other researchers. Moreover, the implementation of the calculation result for automotive capturing trunks by the harvesting head during the logging operation is discussed in particular.

A software for radioactivity measurement of Ra, Th and K in environmental samples

International Nuclear Information System (INIS)

Miao Zhengqiang; Bao Min; Chang Yongfu

2004-01-01

Radio nuclides of soil, rock, construction material, and almost everything around us. There is growing concern about environmental radioactivity from both scientists and public from an institutional or a common point of view. The regulation and standard on evaluating radioactivity of environmental samples have been issued recently by the authorities. We have developed special purpose Gamma spectra analysis software named ErSpec. The software can effectively process and analyze Gamma spectra measured by a NaI(T1) spectrometry, and can give a relatively precise results of radioactivity of 226 Ra, 232 Th and 40 K in environmental samples. The main functions of ErSpec include, processing and analyzing Gamma spectra, displaying some useful information for users, generating report, managing user's priority, logging user's manipulation, etc. Because environmental samples usually have low radioactivity and have complex measurement conditions, relative method is employed in ErSpec, and Channel-by-Channel Least-Squared Estimation is adopted as spectra analyzing method. The arithmetic make use of information extracted from data of hundreds of channels, then give a rather good result. In ErSpec, by using external call of MatLAB Math Lib in Visual C++, accuracy and speed of calculation and robustness of software are improved distinctly. Object-Oriented Programming Method and ActiveX techniques are also employed in software designing and coding stage. (authors)

Contrasting Patterns of Damage and Recovery in Logged Amazon Forests From Small Footprint LiDAR Data

Science.gov (United States)

Morton, D. C.; Keller, M.; Cook, B. D.; Hunter, Maria; Sales, Marcio; Spinelli, L.; Victoria, D.; Andersen, H.-E.; Saleska, S.

2012-01-01

Tropical forests ecosystems respond dynamically to climate variability and disturbances on time scales of minutes to millennia. To date, our knowledge of disturbance and recovery processes in tropical forests is derived almost exclusively from networks of forest inventory plots. These plots typically sample small areas (less than or equal to 1 ha) in conservation units that are protected from logging and fire. Amazon forests with frequent disturbances from human activity remain under-studied. Ongoing negotiations on REDD+ (Reducing Emissions from Deforestation and Forest Degradation plus enhancing forest carbon stocks) have placed additional emphasis on identifying degraded forests and quantifying changing carbon stocks in both degraded and intact tropical forests. We evaluated patterns of forest disturbance and recovery at four -1000 ha sites in the Brazilian Amazon using small footprint LiDAR data and coincident field measurements. Large area coverage with airborne LiDAR data in 2011-2012 included logged and unmanaged areas in Cotriguacu (Mato Grosso), Fiona do Jamari (Rondonia), and Floresta Estadual do Antimary (Acre), and unmanaged forest within Reserva Ducke (Amazonas). Logging infrastructure (skid trails, log decks, and roads) was identified using LiDAR returns from understory vegetation and validated based on field data. At each logged site, canopy gaps from logging activity and LiDAR metrics of canopy heights were used to quantify differences in forest structure between logged and unlogged areas. Contrasting patterns of harvesting operations and canopy damages at the three logged sites reflect different levels of pre-harvest planning (i.e., informal logging compared to state or national logging concessions), harvest intensity, and site conditions. Finally, we used multi-temporal LiDAR data from two sites, Reserva Ducke (2009, 2012) and Antimary (2010, 2011), to evaluate gap phase dynamics in unmanaged forest areas. The rates and patterns of canopy gap

Epileptic Seizure Detection with Log-Euclidean Gaussian Kernel-Based Sparse Representation.

Science.gov (United States)

Yuan, Shasha; Zhou, Weidong; Wu, Qi; Zhang, Yanli

2016-05-01

Epileptic seizure detection plays an important role in the diagnosis of epilepsy and reducing the massive workload of reviewing electroencephalography (EEG) recordings. In this work, a novel algorithm is developed to detect seizures employing log-Euclidean Gaussian kernel-based sparse representation (SR) in long-term EEG recordings. Unlike the traditional SR for vector data in Euclidean space, the log-Euclidean Gaussian kernel-based SR framework is proposed for seizure detection in the space of the symmetric positive definite (SPD) matrices, which form a Riemannian manifold. Since the Riemannian manifold is nonlinear, the log-Euclidean Gaussian kernel function is applied to embed it into a reproducing kernel Hilbert space (RKHS) for performing SR. The EEG signals of all channels are divided into epochs and the SPD matrices representing EEG epochs are generated by covariance descriptors. Then, the testing samples are sparsely coded over the dictionary composed by training samples utilizing log-Euclidean Gaussian kernel-based SR. The classification of testing samples is achieved by computing the minimal reconstructed residuals. The proposed method is evaluated on the Freiburg EEG dataset of 21 patients and shows its notable performance on both epoch-based and event-based assessments. Moreover, this method handles multiple channels of EEG recordings synchronously which is more speedy and efficient than traditional seizure detection methods.

Dual detector neutron lifetime log: theory and practical applications

International Nuclear Information System (INIS)

Serpas, C.J.; Wichmann, P.A.; Fertl, W.H.; DeVries, M.R.; Rndall, R.R.

1977-01-01

The Neutron Lifetime Log instrumentation has continued to evolve and now is equipped with dual detectors for increased ease in gas detection and also a ratio response for a simultaneous porosity determination. A good deal of experimentation was involved to minimize both lithology and salinity effects on the porosity indication. This paper contains a discussion of the theory and concepts related to the application of the Dual Detector Neutron Lifetime Log (DNLL). It is important to note that with these advances the recording of thermal neutron capture cross section (Σ) remains consistent with the past measurements of earlier generations of instruments as the most accurate determination of this parameter. A number of field examples of the newly logged results are shown. These field cases include Dual Detector NLL's run thru the drill strings of highly deviated holes when difficulties were encountered in getting conventional open hole logs to bottom, logs thru open perforations and hot radioactive zones, comparisons of the large and small diameter instruments, logs with anomalous fluids in the annulus, logs thru multiple casing strings, and a number of other examples

Acoustic measurements on trees and logs: a review and analysis

Science.gov (United States)

Xiping Wang

2013-01-01

Acoustic technologies have been well established as material evaluation tools in the past several decades, and their use has become widely accepted in the forest products industry for online quality control and products grading. Recent research developments on acoustic sensing technology offer further opportunities to evaluate standing trees and logs for general wood...

Perpendicular distance sampling: an alternative method for sampling downed coarse woody debris

Science.gov (United States)

Michael S. Williams; Jeffrey H. Gove

2003-01-01

Coarse woody debris (CWD) plays an important role in many forest ecosystem processes. In recent years, a number of new methods have been proposed to sample CWD. These methods select individual logs into the sample using some form of unequal probability sampling. One concern with most of these methods is the difficulty in estimating the volume of each log. A new method...

Mining Experiential Patterns from Game-Logs of Board Game

Directory of Open Access Journals (Sweden)

Liang Wang

2015-01-01

Full Text Available In board games, game-logs record past game processes, which can be regarded as an accumulation of experience. Similar to a real person, a computer player can gradually increase its skill by learning from game-logs. Therefore, the game becomes more interesting. This paper proposes an extensible approach to mine experiential patterns from increasing game-logs. The computer player improves its strategies by utilizing these growing patterns, just as it acquires experience. To evaluate the effect and performance of the approach, we designed a sample board game as a test platform and elaborated an experiment consisting of a series of tests. Experimental results show that our approach is effective and efficient.

SU-F-T-172: A Method for Log File QA On An IBA Proteus System for Patient Specific Spot Scanning Quality Assurance

Energy Technology Data Exchange (ETDEWEB)

Tang, S; Ho, M; Chen, C; Mah, D [ProCure NJ, Somerset, NJ (United States); Rice, I; Doan, D; Mac Rae, B [IBA, Somerset, NJ (United States)

2016-06-15

Purpose: The use of log files to perform patient specific quality assurance for both protons and IMRT has been established. Here, we extend that approach to a proprietary log file format and compare our results to measurements in phantom. Our goal was to generate a system that would permit gross errors to be found within 3 fractions until direct measurements. This approach could eventually replace direct measurements. Methods: Spot scanning protons pass through multi-wire ionization chambers which provide information about the charge, location, and size of each delivered spot. We have generated a program that calculates the dose in phantom from these log files and compares the measurements with the plan. The program has 3 different spot shape models: single Gaussian, double Gaussian and the ASTROID model. The program was benchmarked across different treatment sites for 23 patients and 74 fields. Results: The dose calculated from the log files were compared to those generate by the treatment planning system (Raystation). While the dual Gaussian model often gave better agreement, overall, the ASTROID model gave the most consistent results. Using a 5%–3 mm gamma with a 90% passing criteria and excluding doses below 20% of prescription all patient samples passed. However, the degree of agreement of the log file approach was slightly worse than that of the chamber array measurement approach. Operationally, this implies that if the beam passes the log file model, it should pass direct measurement. Conclusion: We have established and benchmarked a model for log file QA in an IBA proteus plus system. The choice of optimal spot model for a given class of patients may be affected by factors such as site, field size, and range shifter and will be investigated further.

Predicting internal red oak (Quercus rubra) log defect features using surface defect defect measurements

Science.gov (United States)

R. Edward. Thomas

2013-01-01

Determining the defects located within a log is crucial to understanding the tree/log resource for efficient processing. However, existing means of doing this non-destructively requires the use of expensive x-ray/CT (computerized tomography), MRI (magnetic resonance imaging), or microwave technology. These methods do not lend themselves to fast, efficient, and cost-...

Weathering reactions and isometric log-ratio coordinates: Do they speak to each other?

International Nuclear Information System (INIS)

Buccianti, Antonella; Zuo, Renguang

2016-01-01

The aim of this contribution is to explore the relationship among some concepts, often considered to be unrelated, such as weathering reactions, compositional data and fractals by means of distribution analysis. Weathering reactions represent the necessary transfer of heat and entropy to the environment in geochemical cycles. Compositional data express the relative abundance of chemical elements/species in a given total (i.e. volume or weight). Fractals are temporal or spatial objects with self-similarity and scale-invariance, so that internal structures repeat themselves over multiple levels of magnification or scales of measurement. Gibbs's free energy and the application of the Law Mass Action can be used to model weathering reactions, under the hypothesis of chemical equilibrium. Compositional data are obtained in the analytical phase after the determination of the concentrations of chemicals in sampled solid, liquid or gaseous materials. Fractals can be measured by using their fractal dimensions. In this paper, the presence of fractal structures is observed when the frequency distribution of isometric log-ratio coordinates is investigated, showing the logarithm of the cumulative number of samples exceeding a certain coordinate value plotted against the coordinate value itself. Isometric log-ratio coordinates (or balances) were constructed by using the sequential binary partition (SBP) method. The balances were identified to maintain, as far as possible, the similarity with a corresponding weathering reaction affecting the Arno river catchment (Tuscany, central Italy) as described by the Law of Mass Action. The emergence of fractal structures indicates the presence of dissipative systems, which require complexity, large numbers of inter-connected elements and stochasticity. - Highlights: • Frequency distribution analysis links compositional data and fractals. • Isometric log-ratio coordinates simulate chemical reactions in weathering processes. • Fractal

Well logging system with linearity control

International Nuclear Information System (INIS)

Jones, J.M.

1973-01-01

Apparatus is described for controlling the gain of a nuclear well logging system comprising: (1) means for measuring the energy spectrum of gamma rays produced by earth formation materials surrounding a well borehole; (2) means for measuring the number of counts of a gamma rays having an energy falling within each of at least two predetermined energy band portions of the gamma ray energy spectrum; (3) means for generating a signal proportional to the ratio of the gamma ray counts and for comparing the ratio signal with at least one constant ratio calibration signal; (4) means for generating an error signal representative of the difference of the ratio signal and the constant ratio calibration signal; and (5) means for using the error signal to control the linearity of the well logging system. (author)

A Field Study of NMR Logging to Quantify Petroleum Contamination in Subsurface Sediments

Science.gov (United States)

Fay, E. L.; Knight, R. J.; Grunewald, E. D.

2016-12-01

Nuclear magnetic resonance (NMR) measurements are directly sensitive to hydrogen-bearing fluids including water and petroleum products. NMR logging tools can be used to detect and quantify petroleum hydrocarbon contamination in the sediments surrounding a well or borehole. An advantage of the NMR method is that data can be collected in both cased and uncased holes. In order to estimate the volume of in-situ hydrocarbon, there must be sufficient contrast between either the relaxation times (T2) or the diffusion coefficients (D) of water and the contaminant. In a field study conducted in Pine Ridge, South Dakota, NMR logging measurements were used to investigate an area of hydrocarbon contamination from leaking underground storage tanks. A contaminant sample recovered from a monitoring well at the site was found to be consistent with a mixture of gasoline and diesel fuel. NMR measurements were collected in two PVC-cased monitoring wells; D and T2 measurements were used together to detect and quantify contaminant in the sediments above and below the water table at both of the wells. While the contrast in D between the fluids was found to be inadequate for fluid typing, the T2 contrast between the contaminant and water in silt enabled the estimation of the water and contaminant volumes. This study shows that NMR logging can be used to detect and quantify in-situ contamination, but also highlights the importance of sediment and contaminant properties that lead to a sufficiently large contrast in T2 or D.

Quality evaluation of processed clay soil samples.

Science.gov (United States)

Steiner-Asiedu, Matilda; Harrison, Obed Akwaa; Vuvor, Frederick; Tano-Debrah, Kwaku

2016-01-01

This study assessed the microbial quality of clay samples sold on two of the major Ghanaian markets. The study was a cross-sectional assessing the evaluation of processed clay and effects it has on the nutrition of the consumers in the political capital town of Ghana. The items for the examination was processed clay soil samples. Staphylococcus spp and fecal coliforms including Klebsiella, Escherichia, and Shigella and Enterobacterspp were isolated from the clay samples. Samples from the Kaneshie market in Accra recorded the highest total viable counts 6.5 Log cfu/g and Staphylococcal count 5.8 Log cfu/g. For fecal coliforms, Madina market samples had the highest count 6.5 Log cfu/g and also recorded the highest levels of yeast and mould. For Koforidua, total viable count was highest in the samples from the Zongo market 6.3 Log cfu/g. Central market samples had the highest count of fecal coliforms 4.6 Log cfu/g and yeasts and moulds 6.5 Log cfu/g. "Small" market recorded the highest staphylococcal count 6.2 Log cfu/g. The water activity of the clay samples were low, and ranged between 0.65±0.01 and 0.66±0.00 for samples collected from Koforidua and Accra respectively. The clay samples were found to contain Klebsiella spp. Escherichia, Enterobacter, Shigella spp. staphylococcus spp., yeast and mould. These have health implications when consumed.

Neutron capture in borehole logging

International Nuclear Information System (INIS)

Randall, R.R.

1981-01-01

The use is described of a pulsed source of fast neutrons and a radiation detector to measure the thermal neutron population decay rate in a well logging instrument. The macroscopic neutron absorption cross-section is calculated by taking the natural logarithm of the ratio of the detected radiation counts occurring within two measurement intervals of fixed duration and starting at a fixed time after a neutron burst. (U.K.)

Measurement and Evaluation of Finger Tapping Movements Using Log-linearized Gaussian Mixture Networks

Directory of Open Access Journals (Sweden)

Masaru Yokoe

2009-03-01

Full Text Available This paper proposes a method to quantitatively measure and evaluate finger tapping movements for the assessment of motor function using log-linearized Gaussian mixture networks (LLGMNs. First, finger tapping movements are measured using magnetic sensors, and eleven indices are computed for evaluation. After standardizing these indices based on those of normal subjects, they are input to LLGMNs to assess motor function. Then, motor ability is probabilistically discriminated to determine whether it is normal or not using a classifier combined with the output of multiple LLGMNs based on bagging and entropy. This paper reports on evaluation and discrimination experiments performed on finger tapping movements in 33 Parkinson’s disease (PD patients and 32 normal elderly subjects. The results showed that the patients could be classified correctly in terms of their impairment status with a high degree of accuracy (average rate: 93:1 § 3:69% using 12 LLGMNs, which was about 5% higher than the results obtained using a single LLGMN.

Mounting Thin Samples For Electrical Measurements

Science.gov (United States)

Matus, L. G.; Summers, R. L.

1988-01-01

New method for mounting thin sample for electrical measurements involves use of vacuum chuck to hold a ceramic mounting plate, which holds sample. Contacts on mounting plate establish electrical connection to sample. Used to make electrical measurements over temperature range from 77 to 1,000 K and does not introduce distortions into magnetic field during Hall measurements.

New roles of LWD and wireline logging in scientific ocean drilling

Science.gov (United States)

Sanada, Y.; Kido, Y. N.; Moe, K.; Aoike, K.

2014-12-01

D/V Chikyu implemented by CDEX/JAMSTEC joined IODP from 2007. Various LWD (Logging While Drilling) and wireline logging have been carried out in many expeditions and for various purposes. Significant features of logging in Chikyu expeditions are many use of LWD than wireline logging, and riser dirlling. riser selected specific tools for each scientific target, and 3) carried out various borehole experiments. LWD has been more popular than wireline logging in Chikyu expeditions, because its advantages match theirs science targets. The advantages are followings. 1) LWD has more opportunities for measurement in unstable borehole, such as in the series of Nankai trough drilling expeditions. 2) LWD realtime data allows us to make realtime interpretation and operational decision. Realtime interpretation was required to set obsevartory at the properposition. 3) LWD before coring allows us to make a strategy of spot coring.We can design coring intervals for our interest and core length to improve core recovery.Riser drilling brings us merits for logging. One is hole stability (good hole condition) and the other is the use of large diameter tools. Controled drilling mud in riser drilling system prevent mud invasion to formation and mitigates collapse of borehole wall. They reduce the risk of tool stack and improve data quality. Large diameter of riser pipe enhances variation of tool seizes. A couple of new tools were used for new measurement and improvement of the data quality. For example, SonicScanner (trademark of Schulumberger) successfully measured compressional and share velocity in very low velocities at the soft sediment, where it has been difficult to measure them with conventional DSI tool (Exp319). The stress and pore pressure in the borehole were measured with the wireline logging tool, (Schlumberger MDT). The single probe tool enable to measure temporal formation fluid pressure. The double packer tool enable to fracture test by sealing and pumping in the

Nuclear cross section library for oil well logging analysis

International Nuclear Information System (INIS)

Kodeli, I.; Kitsos, S.; Aldama, D.L.; Zefran, B.

2003-01-01

As part of the IRTMBA (Improved Radiation Transport Modelling for Borehole Applications) Project of the EU Community's 5 th Programme a special purpose multigroup cross section library to be used in the deterministic (as well as Monte Carlo) oil well logging particle transport calculations was prepared. This library is expected to improve the prediction of the neutron and gamma spectra at the detector positions of the logging tool, and their use for the interpretation of the neutron logging measurements was studied. Preparation and testing of this library is described. (author)

Study of the reservoirs of Jurassic and Cretaceous periods in the south-cast slope of Central Kara-Kum vault using combination of acoustic logging, neutron-gamma logging, gamma logging, and electrical logging

International Nuclear Information System (INIS)

Meredov, T.M.; Baranov, M.I.

1978-01-01

Considered is the possibility of application of the combination of neutron-gamma logging, gamma logging al partitioncoustic logging and electrical logging to lithologica of sections, discovery reservoir layers in carbonate and terrigeneous sections as well as quantitative estimation of the porosity coefficients values at prospecting areas in the south-east slope of Central Kara-Kum vault. Neutron-gamma logging mostly makes it possible to partition carbonate rocks into limestones, dolomites and their interstitial variaties and to indicate sand stone layers with different degree of carbonate content

Well log characterization of natural gas-hydrates

Science.gov (United States)

Collett, Timothy S.; Lee, Myung W.

2012-01-01

In the last 25 years there have been significant advancements in the use of well-logging tools to acquire detailed information on the occurrence of gas hydrates in nature: whereas wireline electrical resistivity and acoustic logs were formerly used to identify gas-hydrate occurrences in wells drilled in Arctic permafrost environments, more advanced wireline and logging-while-drilling (LWD) tools are now routinely used to examine the petrophysical nature of gas-hydrate reservoirs and the distribution and concentration of gas hydrates within various complex reservoir systems. Resistivity- and acoustic-logging tools are the most widely used for estimating the gas-hydrate content (i.e., reservoir saturations) in various sediment types and geologic settings. Recent integrated sediment coring and well-log studies have confirmed that electrical-resistivity and acoustic-velocity data can yield accurate gas-hydrate saturations in sediment grain-supported (isotropic) systems such as sand reservoirs, but more advanced log-analysis models are required to characterize gas hydrate in fractured (anisotropic) reservoir systems. New well-logging tools designed to make directionally oriented acoustic and propagation-resistivity log measurements provide the data needed to analyze the acoustic and electrical anisotropic properties of both highly interbedded and fracture-dominated gas-hydrate reservoirs. Advancements in nuclear magnetic resonance (NMR) logging and wireline formation testing (WFT) also allow for the characterization of gas hydrate at the pore scale. Integrated NMR and formation testing studies from northern Canada and Alaska have yielded valuable insight into how gas hydrates are physically distributed in sediments and the occurrence and nature of pore fluids(i.e., free water along with clay- and capillary-bound water) in gas-hydrate-bearing reservoirs. Information on the distribution of gas hydrate at the pore scale has provided invaluable insight on the mechanisms

Predicting the Rate of River Bank Erosion Caused by Large Wood Log

Science.gov (United States)

Zhang, N.; Rutherfurd, I.; Ghisalberti, M.

2016-12-01

When a single tree falls into a river channel, flow is deflected and accelerated between the tree roots and the bank face, increasing shear stress and scouring the bank. The scallop shaped erosion increases the diversity of the channel morphology, but also causes concern for adjacent landholders. Concern about increased bank erosion is one of the main reasons for large wood to still be removed from channels in SE Australia. Further, the hydraulic effect of many logs in the channel can reduce overall bank erosion rates. Although both phenomena have been described before, this research develops a hydraulic model that estimates their magnitude, and tests and calibrates this model with flume and field measurements, with logs with various configurations and sizes. Specifically, the model estimates the change in excess shear stress on the bank associated . The model addresses the effect of the log angle, distance from bank, and log size and flow condition by solving the mass continuity and energy conservation between the cross section at the approaching flow and contracted flow. Then, we evaluate our model against flume experiment preformed with semi-realistic log models to represent logs in different sizes and decay stages by comparing the measured and simulated velocity increase in the gap between the log and the bank. The log angle, distance from bank, and flow condition are systemically varied for each log model during the experiment. Final, the calibrated model is compared with the field data collected in anabranching channels of Murray River in SE Australia where there are abundant instream logs and regulated and consistent high flow for irrigation. Preliminary results suggest that a log can significantly increase the shear stress on the bank, especially when it positions perpendicular to the flow. The shear stress increases with the log angle in a rising curve (The log angle is the angle between log trunk and flow direction. 0o means log is parallel to flow with

The Meaning of Logs

NARCIS (Netherlands)

Etalle, Sandro; Massacci, Fabio; Yautsiukhin, Artsiom

2007-01-01

While logging events is becoming increasingly common in computing, in communication and in collaborative work, log systems need to satisfy increasingly challenging (if not conflicting) requirements.Despite the growing pervasiveness of log systems, to date there is no high-level framework which

The Meaning of Logs

NARCIS (Netherlands)

Etalle, Sandro; Massacci, Fabio; Yautsiukhin, Artsiom; Lambrinoudakis, Costas; Pernul, Günther; Tjoa, A Min

While logging events is becoming increasingly common in computing, in communication and in collaborative environments, log systems need to satisfy increasingly challenging (if not conflicting) requirements. In this paper we propose a high-level framework for modeling log systems, and reasoning about

Detection of attack-targeted scans from the Apache HTTP Server access logs

Directory of Open Access Journals (Sweden)

Merve Baş Seyyar

2018-01-01

Full Text Available A web application could be visited for different purposes. It is possible for a web site to be visited by a regular user as a normal (natural visit, to be viewed by crawlers, bots, spiders, etc. for indexing purposes, lastly to be exploratory scanned by malicious users prior to an attack. An attack targeted web scan can be viewed as a phase of a potential attack and can lead to more attack detection as compared to traditional detection methods. In this work, we propose a method to detect attack-oriented scans and to distinguish them from other types of visits. In this context, we use access log files of Apache (or ISS web servers and try to determine attack situations through examination of the past data. In addition to web scan detections, we insert a rule set to detect SQL Injection and XSS attacks. Our approach has been applied on sample data sets and results have been analyzed in terms of performance measures to compare our method and other commonly used detection techniques. Furthermore, various tests have been made on log samples from real systems. Lastly, several suggestions about further development have been also discussed.

Development of an Intelligent System to Synthesize Petrophysical Well Logs

Directory of Open Access Journals (Sweden)

Morteza Nouri Taleghani

2013-07-01

Full Text Available Porosity is one of the fundamental petrophysical properties that should be evaluated for hydrocarbon bearing reservoirs. It is a vital factor in precise understanding of reservoir quality in a hydrocarbon field. Log data are exceedingly crucial information in petroleum industries, for many of hydrocarbon parameters are obtained by virtue of petrophysical data. There are three main petrophysical logging tools for the determination of porosity, namely neutron, density, and sonic well logs. Porosity can be determined by the use of each of these tools; however, a precise analysis requires a complete set of these tools. Log sets are commonly either incomplete or unreliable for many reasons (i.e. incomplete logging, measurement errors, and loss of data owing to unsuitable data storage. To overcome this drawback, in this study several intelligent systems such as fuzzy logic (FL, neural network (NN, and support vector machine are used to predict synthesized petrophysical logs including neutron, density, and sonic. To accomplish this, the petrophysical well logs data were collected from a real reservoir in one of Iran southwest oil fields. The corresponding correlation was obtained through the comparison of synthesized log values with real log values. The results showed that all intelligent systems were capable of synthesizing petrophysical well logs, but SVM had better accuracy and could be used as the most reliable method compared to the other techniques.

Elemental logging in the KTB Pilot Hole. Pt. 1

International Nuclear Information System (INIS)

Grau, J.A.; Schweitzer, J.S.; Draxler, J.K.; Gatto, H.; Lauterjung, J.

1993-01-01

Neutron-induced γ-ray spectrometry, of prompt capture and delayed activation, together with natural γ-ray measurements, provide a borehole elemental analysis to characterize rock matrix composition. Elemental concentrations from the prompt capture measurements are derived through the use of a closure model that was developed from data on rocks in a sedimentary environment. This set of spectrometers was used to log the 4000 m of the German Continental Deep Drilling Project (KTB) Pilot Hole. The model was tested, with a minor change, for suitability to the crystalline rock environment. Good overall agreement was found between the logging measurements and laboratory analyses performed on cuttings and cores. (Author)

Report on televiewer log and stress measurements in core hole USW G-2, Nevada Test Site, October-November, 1982

International Nuclear Information System (INIS)

Stock, J.M.; Healy, J.H.; Hickman, S.H.

1984-01-01

Hydraulic fracturing stress measurements and a borehole televiewer log were obtained in hole USW G-2 at Yucca Mountain, Nevada, to depths of 1200 m. Results indicate that at the depths tested, the minimum ad maximum horizontal stresses are less than the vertical stress, corresponding to a normal faulting stress regime. Drilling-induced hydrofractures seen in the televiewer log imply a least horizontal principal stress direction of N 60 0 W to N 65 0 W. For reasonable values of the coefficient of friction, the magnitude of the least horizontal stress is close to the value at which slip would occur on preexisting faults of optimal orientation (strike N 25 0 E to N 30 0 E and dipping 60 0 to 67 0 ). The prominent drilling-induced fractures seen in the televiewer log are believed to have been caused by excess downhole pressures applied during drilling the hole. Many throughgoing fractures are also seen in the televiewer log; most of these are high angle, stringing N 10 0 E to N 40 0 E. These fractures show a general decrease in angle of dip with depth. Stress-induced wellbore breakouts are seen at depths below 1050 m. The average N 60 0 W azimuth of these breakouts agrees very closely with the N 60 0 W to N 65 0 W direction of least horizontal principal stress inferred from the drilling-induced hydrofracs. 19 references, 13 figures, 3 tables

SDSS Log Viewer: visual exploratory analysis of large-volume SQL log data

Science.gov (United States)

Zhang, Jian; Chen, Chaomei; Vogeley, Michael S.; Pan, Danny; Thakar, Ani; Raddick, Jordan

2012-01-01

User-generated Structured Query Language (SQL) queries are a rich source of information for database analysts, information scientists, and the end users of databases. In this study a group of scientists in astronomy and computer and information scientists work together to analyze a large volume of SQL log data generated by users of the Sloan Digital Sky Survey (SDSS) data archive in order to better understand users' data seeking behavior. While statistical analysis of such logs is useful at aggregated levels, efficiently exploring specific patterns of queries is often a challenging task due to the typically large volume of the data, multivariate features, and data requirements specified in SQL queries. To enable and facilitate effective and efficient exploration of the SDSS log data, we designed an interactive visualization tool, called the SDSS Log Viewer, which integrates time series visualization, text visualization, and dynamic query techniques. We describe two analysis scenarios of visual exploration of SDSS log data, including understanding unusually high daily query traffic and modeling the types of data seeking behaviors of massive query generators. The two scenarios demonstrate that the SDSS Log Viewer provides a novel and potentially valuable approach to support these targeted tasks.

Tree damage from skyline logging in a western larch/Douglas-fir stand

Science.gov (United States)

Robert E. Benson; Michael J. Gonsior

1981-01-01

Damage to shelterwood leave trees and to understory trees in shelterwood and clearcut logging units logged with skyline yarders was measured, and related to stand conditions, harvesting specifications, and yarding system-terrain interactions. About 23 percent of the marked leave trees in the shelterwood units were killed in logging, and about 10 percent had moderate to...

Static dictionaries on AC⁰ RAMs: query time (√log n/log log n) is necessary and sufficient

DEFF Research Database (Denmark)

Andersson, Arne; Miltersen, Peter Bro; Riis, Søren

1996-01-01

) on the time for answering membership queries in a set of size n when reasonable space is used for the data structure storing the set; the upper bound can be obtained using O(n) space, and the lower bound holds even if we allow space 2polylog n. Several variations of this result are also obtained. Among others......, we show a tradeoff between time and circuit depth under the unit-cost assumption: any RAM instruction set which permits a linear space, constant query time solution to the static dictionary problem must have an instruction of depth Ω(log w/log log to), where w is the word size of the machine (and log...

Two-stage recovery of amphibian assemblages following selective logging of tropical forests.

Science.gov (United States)

Adum, Gilbert Baase; Eichhorn, Markus Peter; Oduro, William; Ofori-Boateng, Caleb; Rödel, Mark-Oliver

2013-04-01

There is a lack of quantitative information on the effectiveness of selective-logging practices in ameliorating effects of logging on faunal communities. We conducted a large-scale replicated field study in 3 selectively logged moist semideciduous forests in West Africa at varying times after timber extraction to assess post logging effects on amphibian assemblages. Specifically, we assessed whether the diversity, abundance, and assemblage composition of amphibians changed over time for forest-dependent species and those tolerant of forest disturbance. In 2009, we sampled amphibians in 3 forests (total of 48 study plots, each 2 ha) in southwestern Ghana. In each forest, we established plots in undisturbed forest, recently logged forest, and forest logged 10 and 20 years previously. Logging intensity was constant across sites with 3 trees/ha removed. Recently logged forests supported substantially more species than unlogged forests. This was due to an influx of disturbance-tolerant species after logging. Simultaneously Simpson's index decreased, with increased in dominance of a few species. As time since logging increased richness of disturbance-tolerant species decreased until 10 years after logging when their composition was indistinguishable from unlogged forests. Simpson's index increased with time since logging and was indistinguishable from unlogged forest 20 years after logging. Forest specialists decreased after logging and recovered slowly. However, after 20 years amphibian assemblages had returned to a state indistinguishable from that of undisturbed forest in both abundance and composition. These results demonstrate that even with low-intensity logging (≤3 trees/ha) a minimum 20-year rotation of logging is required for effective conservation of amphibian assemblages in moist semideciduous forests. Furthermore, remnant patches of intact forests retained in the landscape and the presence of permanent brooks may aid in the effective recovery of amphibian

Rapid increase in log populations in drought-stressed mixed-conifer and ponderosa pine forests in northern Arizona

Science.gov (United States)

Joseph L. Ganey; Scott C. Vojta

2012-01-01

Down logs provide important ecosystem services in forests and affect surface fuel loads and fire behavior. Amounts and kinds of logs are influenced by factors such as forest type, disturbance regime, forest man-agement, and climate. To quantify potential short-term changes in log populations during a recent global- climate-change type drought, we sampled logs in mixed-...

Geomicrobial Optical Logging Detectors (GOLD)

Science.gov (United States)

Bramall, N. E.; Stoker, C. R.; Price, P. B.; Coates, J. D.; Allamandola, L. J.; Mattioda, A. L.

2008-12-01

We will present concepts for downhole instrumentation that could be used in the Deep Underground Science and Engineering Laboratory (DUSEL). We envision optical borehole-logging instruments that could monitor bacterial concentration, mineralogy, aromatic organics, temperature and oxygen concentration, allowing for the in situ monitoring of time-dependent microbial and short-scale geologic processes and provide valuable in situ data on stratigraphy to supplement core analyses, especially where instances of missing or damaged core sections make such studies difficult. Incorporated into these instruments will be a sampling/inoculation tool to allow for the recovery and/or manipulation of particularly interesting sections of the borehole wall for further study, enabling a series of microbiological studies. The borehole tools we will develop revolve around key emerging technologies and methods, some of which are briefly described below: 1) Autofluorescence Spectroscopy: Building on past instruments, we will develop a new borehole logger that searches for microbial life and organics using fluorescence spectroscopy. Many important organic compounds (e.g. PAHs) and biomolecules (e.g. aromatic amino acids, proteins, methanogenic coenzymes) fluoresce when excited with ultraviolet and visible light. Through the careful selection of excitation wavelength(s) and temporal gating parameters, a borehole logging instrument can detect and differentiate between these different compounds and the mineral matrix in which they exist. 2) Raman Spectroscopy: Though less sensitive than fluorescence spectroscopy, Raman spectroscopy is more definitive: it can provide important mineral phase distribution/proportions and other chemical data enabling studies of mineralogy and microbe-mineral interactions (when combined with fluorescence). 3) Borehole Camera: Imaging of the borehole wall with extended information in the UV, visible, and NIR for a more informative view can provide a lot of insight

Processing well logging data, for example for verification and calibration of well logs

International Nuclear Information System (INIS)

Suau, J.; Boutemy, Y.

1981-01-01

A method is described of machine processing well logging data derived from borehole exploring devices which investigate earth formations traversed by boreholes. The method can be used for verifying and recalibrating logs, reconstructing missing logs and combining the data to form a statistical model of the traversed earth formations. (U.K.)

Permeability Estimation Directly From Logging-While-Drilling Induced Polarization Data

DEFF Research Database (Denmark)

Fiandaca, G.; Maurya, P.K.; Balbarini, Nicola

2018-01-01

In this study we present the prediction of permeability from time‐domain spectral induced polarization (IP) data, measured in boreholes on undisturbed formations using the El‐log logging‐while‐drilling technique. We collected El‐log data and hydraulic properties on unconsolidated Quaternary...... and Miocene deposits in boreholes at three locations at a field site in Denmark, characterized by different electrical water conductivity and chemistry. The high vertical resolution of the El‐log technique matches the lithological variability at the site, minimizing ambiguity in the interpretation originating...

La logística integral como ventaja competitiva y sistema logístico

Directory of Open Access Journals (Sweden)

Mario Anselmo Martínez gallardo

2013-07-01

Full Text Available Esta investigación analiza la logística integral como una ventaja competitiva y el sistema logístico. Es opinión de los autores que la logística integral es esencial para el intercambio de mercancías, toda vez que reduce costos y hace más ágil la actividad comercial. La utilización de esta logística representa una ventaja competitiva con respecto de otras empresas por la optimización del capital y ahorro de tiempo.

Target recognition of log-polar ladar range images using moment invariants

Science.gov (United States)

Xia, Wenze; Han, Shaokun; Cao, Jie; Yu, Haoyong

2017-01-01

The ladar range image has received considerable attentions in the automatic target recognition field. However, previous research does not cover target recognition using log-polar ladar range images. Therefore, we construct a target recognition system based on log-polar ladar range images in this paper. In this system combined moment invariants and backpropagation neural network are selected as shape descriptor and shape classifier, respectively. In order to fully analyze the effect of log-polar sampling pattern on recognition result, several comparative experiments based on simulated and real range images are carried out. Eventually, several important conclusions are drawn: (i) if combined moments are computed directly by log-polar range images, translation, rotation and scaling invariant properties of combined moments will be invalid (ii) when object is located in the center of field of view, recognition rate of log-polar range images is less sensitive to the changing of field of view (iii) as object position changes from center to edge of field of view, recognition performance of log-polar range images will decline dramatically (iv) log-polar range images has a better noise robustness than Cartesian range images. Finally, we give a suggestion that it is better to divide field of view into recognition area and searching area in the real application.

Prediction of thermal conductivity of sedimentary rocks from well logs

DEFF Research Database (Denmark)

Fuchs, Sven; Förster, Andrea

2014-01-01

The calculation of heat-flow density in boreholes requires reliable values for the change of temperature and rock thermal conductivity with depth. As rock samples for laboratory measurements of thermal conductivity (TC) are usually rare geophysical well logs are used alternatively to determine TC...... parameters (i.e. thermal conductivity, density, hydrogen index, sonic interval transit time, gamma-ray response, photoelectric factor) of artificial mineral assemblages consisting 15 rock-forming minerals that are used in different combinations to typify sedimentary rocks. The predictive capacity of the new...... equations is evaluated on subsurface data from four boreholes drilled into the Mesozoic sequence of the North German Basin, including more than 1700 laboratory-measured thermal-conductivity values. Results are compared with those from other approaches published in the past. The new approach predicts TC...

Value of NMR logging for heavy oil characterization

Energy Technology Data Exchange (ETDEWEB)

Chen, S.; Chen, J.; Georgi, D. [Baker Hughes, Calgary, AB (Canada); Sun, B. [Chevron Energy Technology Co., Calgary, AB (Canada)

2008-07-01

Non-conventional, heavy oil fields are becoming increasingly important to the security of energy supplies and are becoming economically profitable to produce. Heavy oil reservoirs are difficult to evaluate since they are typically shallow and the connate waters are very fresh. Other heavy oil reservoirs are oil-wet where the resistivities are not indicative of saturation. Nuclear magnetic resonance (NMR) detects molecular level interactions. As such, it responds distinctively to different hydrocarbon molecules, thereby opening a new avenue for constituent analysis. This feature makes NMR a more powerful technique than bulk oil density or viscosity measurements for characterizing oils, and is the basis for detecting gas in heavy oil fields. NMR logging, which measures fluid in pore space directly, is capable of separating oil from water. It is possible to discern movable from bound water by analyzing NMR logs. The oil viscosity can be also quantified from NMR logs, NMR relaxation time and diffusivity estimates. The unique challenges for heavy oil reservoir characterization for the NMR technique were discussed with reference to the extra-fast decay of the NMR signal in response to extra-heavy oil/tars, and the lack of sensitivity in measuring very slow diffusion of heavy oil molecules. This paper presented various methods for analyzing heavy oil reservoirs in different viscosity ranges. Heavy oil fields in Venezuela, Kazakhstan, Canada, Alaska and the Middle East were analyzed using different data interpretation approaches based on the reservoir formation characteristics and the heavy oil type. NMR direct fluid typing was adequate for clean sands and carbonate reservoirs while integrated approaches were used to interpret extra heavy oils and tars. It was concluded that NMR logs can provide quantitative measures for heavy oil saturation, identify sweet spots or tar streaks, and quantify heavy oil viscosity within reasonable accuracy. 14 refs., 16 figs.

The log S -log N distribution of gamma ray brust

International Nuclear Information System (INIS)

Yamagami, Takamasa; Nishimura, Jun; Fujii, Masami

1982-01-01

The relation between the size S and the frequency N of gamma ray burst has been studied. This relation may be determined from the celestial distribution of gamma ray burst sources. The present analysis gives that the log S - log N relation for any direction is determined by the celestial distribution of gamma ray burst sources. The observed bursts were analyzed. The celestial distribution of gamma ray burst sources was observed by the satellites of USSR. The results showed that the distribution seemed to be isotropic. However, the calculated log S - log N relation based on the isotropic distribution wasF in disagreement with the observed ones. As the result of analysis, it was found that the observed bursts missed low energy part because of the threshold of detectors. The levels of discrimination of detection were not clear. When a proper threshold level is set for each type of burst, and the size of bursts is determined, the above mentioned discrepancy will be deleted regardless of luminosity and the spatial distribution of bursts. (Kato, T.)

The SAMPL5 challenge for embedded-cluster integral equation theory: solvation free energies, aqueous p$K_a$, and cyclohexane–water log D

CERN Document Server

Tielker, Nicolas; Heil, Jochen; Kloss, Thomas; Ehrhart, Sebastian; Güssregen, Stefan; Schmidt, K. Friedemann; Kast, Stefan M.

2016-01-01

We predict cyclohexane–water distribution coefficients (log D7.4) for drug-like molecules taken from the SAMPL5 blind prediction challenge by the “embedded cluster reference interaction site model” (EC-RISM) integral equation theory. This task involves the coupled problem of predicting both partition coefficients (log P) of neutral species between the solvents and aqueous acidity constants (pKa) in order to account for a change of protonation states. The first issue is addressed by calibrating an EC-RISM-based model for solvation free energies derived from the “Minnesota Solvation Database” (MNSOL) for both water and cyclohexane utilizing a correction based on the partial molar volume, yielding a root mean square error (RMSE) of 2.4 kcal mol−1 for water and 0.8–0.9 kcal mol−1 for cyclohexane depending on the parametrization. The second one is treated by employing on one hand an empirical pKa model (MoKa) and, on the other hand, an EC-RISM-derived regression of published acidity constants (RMSE...

An in-situ check of the epithermal neutron log calibration

International Nuclear Information System (INIS)

Burkhard, N.R.

1993-01-01

The epithermal neutron log is used to measure the water content of the formation. The large hole epithermal neutron sonde (ENS) utilized at the Nevada Test Site (NTS) has been calibrated in the Hydrogen Content Test Facility (HCTF). These calibrations are used to correct the measured neutron count rate for the effects of tool stand-off and density. For some time, the suspicion has existed that the water contents that are calculated from the ENS data are too large. Hole U2gj represented a unique opportunity to check the validity of the ENS calibration under realistic logging conditions; a portion of the hole had been cemented and redrilled and then logged. The cements have a known water content and can be used as an in-situ calibration check. The author found that the water contents from the log data after processing with the existing calibrations are consistent with these known cement water contents. In addition, the study indicates that the raw neutron data might be more appropriately smoothed by using a median smoother rather than the currently utilized mean smoother

An in-situ check of the epithermal neutron log calibration

International Nuclear Information System (INIS)

Burkhard, N.R.

1993-09-01

The epithermal neutron log is used to measure the water content of the formation. The large hole epithermal neutron sonde (ENS) that we utilize at the Nevada Test Site (NTS) has been calibrated in the Hydrogen Content Test Facility (HCTF). These calibrations are used to correct the measured neutron count rate for the effects of tool stand-off and density. For sometime, the suspicion has existed that the water contents that are calculated from the ENS data are too large. Hole U2gj represented a unique opportunity to check the validity of the ENS calibration under realistic logging conditions; a portion of the hole had been cemented and re drilled and then logged. The cements have a known water content and can be used as an in situ calibration check. I found that the water contents from the log data after processing with the existing calibrations are consistent with these known cement water contents. In addition, the study indicates that the raw neutron data might be more appropriately smoothed by using a median smoother rather than the currently utilized mean smoother

Accuracy and borehole influences in pulsed neutron gamma density logging while drilling.

Science.gov (United States)

Yu, Huawei; Sun, Jianmeng; Wang, Jiaxin; Gardner, Robin P

2011-09-01

A new pulsed neutron gamma density (NGD) logging has been developed to replace radioactive chemical sources in oil logging tools. The present paper describes studies of near and far density measurement accuracy of NGD logging at two spacings and the borehole influences using Monte-Carlo simulation. The results show that the accuracy of near density is not as good as far density. It is difficult to correct this for borehole effects by using conventional methods because both near and far density measurement is significantly sensitive to standoffs and mud properties. Copyright © 2011 Elsevier Ltd. All rights reserved.

Radioisotope Sample Measurement Techniques in Medicine and Biology. Proceedings of the Symposium on Radioisotope Sample Measurement Techniques

International Nuclear Information System (INIS)

1965-01-01

The medical and biological applications of radioisotopes depend on two basically different types of measurements, those on living subjects in vivo and those on samples in vitro. The International Atomic Energy Agency has in the past held several meetings on in vivo measurement techniques, notably whole-body counting and radioisotope scanning. The present volume contains the Proceedings of the first Symposium the Agency has organized to discuss the various aspects of techniques for sample measurement in vitro. The range of these sample measurement techniques is very wide. The sample may weigh a few milligrams or several hundred grams, and may be in the gaseous, liquid or solid state. Its radioactive content may consist of a single, known radioisotope or several unknown ones. The concentration of radioactivity may be low, medium or high. The measurements may be made manually or automatically and any one of the many radiation detectors now available may be used. The 53 papers presented at the Symposium illustrate the great variety of methods now in use for radioactive- sample measurements. The first topic discussed is gamma-ray spectrometry, which finds an increasing number of applications in sample measurements. Other sections of the Proceedings deal with: the use of computers in gamma-ray spectrometry and multiple tracer techniques; recent developments in activation analysis where both gamma-ray spectrometry and computing techniques are applied; thin-layer and paper radio chromatographic techniques for use with low energy beta-ray emitters; various aspects of liquid scintillation counting techniques in the measurement of alpha- and beta-ray emitters, including chemical and colour quenching; autoradiographic techniques; calibration of equipment; and standardization of radioisotopes. Finally, some applications of solid-state detectors are presented; this section may be regarded as a preview of important future developments. The meeting was attended by 203 participants

Preliminary report on NTS spectral gamma logging and calibration models

International Nuclear Information System (INIS)

Mathews, M.A.; Warren, R.G.; Garcia, S.R.; Lavelle, M.J.

1985-01-01

Facilities are now available at the Nevada Test Site (NTS) in Building 2201 to calibrate spectral gamma logging equipment in environments of low radioactivity. Such environments are routinely encountered during logging of holes at the NTS. Four calibration models were delivered to Building 2201 in January 1985. Each model, or test pit, consists of a stone block with a 12-inch diameter cored borehole. Preliminary radioelement values from the core for the test pits range from 0.58 to 3.83% potassium (K), 0.48 to 29.11 ppm thorium (Th), and 0.62 to 40.42 ppm uranium (U). Two satellite holes, U19ab number2 and U19ab number3, were logged during the winter of 1984-1985. The response of these logs correlates with contents of the naturally radioactive elements K. Th. and U determined in samples from petrologic zones that occur within these holes. Based on these comparisons, the spectral gamma log aids in the recognition and mapping of subsurface stratigraphic units and alteration features associated with unusual concentration of these radioactive elements, such as clay-rich zones

Analyzing Decision Logs to Understand Decision Making in Serious Crime Investigations.

Science.gov (United States)

Dando, Coral J; Ormerod, Thomas C

2017-12-01

Objective To study decision making by detectives when investigating serious crime through the examination of decision logs to explore hypothesis generation and evidence selection. Background Decision logs are used to record and justify decisions made during serious crime investigations. The complexity of investigative decision making is well documented, as are the errors associated with miscarriages of justice and inquests. The use of decision logs has not been the subject of an empirical investigation, yet they offer an important window into the nature of investigative decision making in dynamic, time-critical environments. Method A sample of decision logs from British police forces was analyzed qualitatively and quantitatively to explore hypothesis generation and evidence selection by police detectives. Results Analyses revealed diversity in documentation of decisions that did not correlate with case type and identified significant limitations of the decision log approach to supporting investigative decision making. Differences emerged between experienced and less experienced officers' decision log records in exploration of alternative hypotheses, generation of hypotheses, and sources of evidential inquiry opened over phase of investigation. Conclusion The practical use of decision logs is highly constrained by their format and context of use. Despite this, decision log records suggest that experienced detectives display strategic decision making to avoid confirmation and satisficing, which affect less experienced detectives. Application Potential applications of this research include both training in case documentation and the development of new decision log media that encourage detectives, irrespective of experience, to generate multiple hypotheses and optimize the timely selection of evidence to test them.

Estimation of the non records logs from existing logs using artificial neural networks

Directory of Open Access Journals (Sweden)

Mehdi Mohammad Salehi

2017-12-01

Full Text Available Finding the information of the hydrocarbon reservoirs from well logs is one of the main objectives of the engineers. But, missing the log records (due to many reasons such as broken instruments, unsuitable borehole and etc. is a major challenge to achieve it. Prediction of the density and resistivity logs (Rt, DT and LLS from the conventional wire-line logs in one of the Iranian southwest oil fields is the main purpose of this study. Multilayer neural network was applied to develop an intelligent predictive model for prediction of the logs. A total of 3000 data sets from 3 wells (A, B and C of the studied field were used. Among them, the data of A, B and C wells were used to constructing and testing the model, respectively. To evaluate the performance of the model, the mean square error (MSE and correlation coefficient (R2 in the test data were calculated. A comparison between the MSE of the proposed model and recently intelligent models shows that the proposed model is more accurate than others. Acceptable accuracy and using conventional well logging data are the highlight advantages of the proposed intelligent model.

Optimized Design of Spacing in Pulsed Neutron Gamma Density Logging While Drilling

Directory of Open Access Journals (Sweden)

ZHANG Feng;HAN Zhong-yue;WU He;HAN Fei

2016-10-01

Full Text Available Radioactive source, used in traditional density logging, has great impact on the environment, while the pulsed neutron source applied in the logging tool is more safety and greener. In our country, the pulsed neutron-gamma density logging technology is still in the stage of development. Optimizing the parameters of neutron-gamma density instrument is essential to improve the measuring accuracy. This paper mainly studied the effects of spacing to typical neutron-gamma density logging tool which included one D-T neutron generator and two gamma scintillation detectors. The optimization of spacing were based on measuring sensitivity and counting statistic. The short spacing from 25 to 35 cm and long spacing from 60 to 65 cm were selected as the optimal position for near and far detector respectively. The result can provide theoretical support for design and manufacture of the instrument.

Logging disturbance shifts net primary productivity and its allocation in Bornean tropical forests.

Science.gov (United States)

Riutta, Terhi; Malhi, Yadvinder; Kho, Lip Khoon; Marthews, Toby R; Huaraca Huasco, Walter; Khoo, MinSheng; Tan, Sylvester; Turner, Edgar; Reynolds, Glen; Both, Sabine; Burslem, David F R P; Teh, Yit Arn; Vairappan, Charles S; Majalap, Noreen; Ewers, Robert M

2018-01-24

Tropical forests play a major role in the carbon cycle of the terrestrial biosphere. Recent field studies have provided detailed descriptions of the carbon cycle of mature tropical forests, but logged or secondary forests have received much less attention. Here, we report the first measures of total net primary productivity (NPP) and its allocation along a disturbance gradient from old-growth forests to moderately and heavily logged forests in Malaysian Borneo. We measured the main NPP components (woody, fine root and canopy NPP) in old-growth (n = 6) and logged (n = 5) 1 ha forest plots. Overall, the total NPP did not differ between old-growth and logged forest (13.5 ± 0.5 and 15.7 ± 1.5 Mg C ha -1  year -1 respectively). However, logged forests allocated significantly higher fraction into woody NPP at the expense of the canopy NPP (42% and 48% into woody and canopy NPP, respectively, in old-growth forest vs 66% and 23% in logged forest). When controlling for local stand structure, NPP in logged forest stands was 41% higher, and woody NPP was 150% higher than in old-growth stands with similar basal area, but this was offset by structure effects (higher gap frequency and absence of large trees in logged forest). This pattern was not driven by species turnover: the average woody NPP of all species groups within logged forest (pioneers, nonpioneers, species unique to logged plots and species shared with old-growth plots) was similar. Hence, below a threshold of very heavy disturbance, logged forests can exhibit higher NPP and higher allocation to wood; such shifts in carbon cycling persist for decades after the logging event. Given that the majority of tropical forest biome has experienced some degree of logging, our results demonstrate that logging can cause substantial shifts in carbon production and allocation in tropical forests. © 2018 John Wiley & Sons Ltd.

How precise is the finite sample approximation of the asymptotic distribution of realised variation measures in the presence of jumps?

DEFF Research Database (Denmark)

Veraart, Almut

2011-01-01

and present a new estimator for the asymptotic "variance" of the centered realised variance in the presence of jumps. Next, we compare the finite sample performance of the various estimators by means of detailed Monte Carlo studies. Here we study the impact of the jump activity, of the jump size of the jumps......This paper studies the impact of jumps on volatility estimation and inference based on various realised variation measures such as realised variance, realised multipower variation and truncated realised multipower variation. We review the asymptotic theory of those realised variation measures...... in the price and of the presence of additional independent or dependent jumps in the volatility. We find that the finite sample performance of realised variance and, in particular, of log--transformed realised variance is generally good, whereas the jump--robust statistics tend to struggle in the presence...

Geophysical well logging operations and log analysis in Geothermal Well Desert Peak No. B-23-1

Energy Technology Data Exchange (ETDEWEB)

Sethi, D.K.; Fertl, W.H.

1980-03-01

Geothermal Well Desert Peak No. B-23-1 was logged by Dresser Atlas during April/May 1979 to a total depth of 2939 m (9642 ft). A temperature of 209/sup 0/C (408/sup 0/F) was observed on the maximum thermometer run with one of the logging tools. Borehole tools rated to a maximum temperature of 204.4/sup 0/C (400/sup 0/F) were utilized for logging except for the Densilog tool, which was from the other set of borehole instruments, rated to a still higher temperature, i.e., 260/sup 0/C (500/sup 0/F). The quality of the logs recorded and the environmental effects on the log response have been considered. The log response in the unusual lithologies of igneous and metamorphic formations encountered in this well could be correlated with the drill cutting data. An empirical, statistical log interpretation approach has made it possible to obtain meaningful information on the rocks penetrated. Various crossplots/histograms of the corrected log data have been generated on the computer. These are found to provide good resolution between the lithological units in the rock sequence. The crossplotting techniques and the statistical approach were combined with the drill cutting descriptions in order to arrive at the lithological characteristics. The results of log analysis and recommendations for logging of future wells have been included.

Theoretical and Numerical Study of Seismoelectric Logs for Logging While Drilling (LWD

Directory of Open Access Journals (Sweden)

Sun Xiang-Yang

2017-01-01

Full Text Available When the acoustic field propagates in the porous medium, the electromagnetic wave can be induced by the seismoelectric effects which can be used in the logging. This paper studies the seismoelectric wave field and deduces the formulations of the acoustic and electromagnetic field of the liquid in the well, and gives the acoustic and electromagnetic boundary conditions between the driller collar and the log liquid, when the driller collar is added. We also do the numerical simulation of the seismoelectric wave field excited by monopole source, study the velocity dispersion characteristics of the acoustic and electromagnetic field, and investigate the detective depth of the seismoelectric logs. Through the simulation we know the seismoelectric logs can avoid the interference of drill collar wave. This paper also provides theoretical guidance for the design of receiving antenna.

Face logging in Copenhagen Limestone, Denmark

DEFF Research Database (Denmark)

Jakobsen, Lisa; Foged, Niels Nielsen; Erichsen, Lars

2015-01-01

tunnel in Copenhagen more than 2.5 km face logs were made in 467 locations at underground stations, shafts, caverns and along bored tunnels. Over 160 geotechnical boreholes, many with geophysical logging were executed prior to construction works. The bedrock consists of Paleogene "Copenhagen limestone......The requirement for excavation support can be assessed from face logging. Face logs can also improve our knowledge of lithological and structural conditions within bedrock and supplement information from boreholes and geophysical logs. During the construction of 8 km metro tunnel and 4 km heating....... The induration degrees recorded in face logs and boreholes are compared and correlated. Distinct geophysical log markers are used to divide the limestone into three units. These marker horizons are correlated between face logs and geotechnical boreholes. A 3D model of the strength variations recorded within...

Drilling, construction, geophysical log data, and lithologic log for boreholes USGS 142 and USGS 142A, Idaho National Laboratory, Idaho

Science.gov (United States)

Twining, Brian V.; Hodges, Mary K.V.; Schusler, Kyle; Mudge, Christopher

2017-07-27

ranged in thickness from about 2 to 100 ft and varied from highly fractured to dense, and ranged from massive to diktytaxitic to scoriaceous, in texture.Geophysical logs were collected on completion of drilling at boreholes USGS 142 and USGS 142A. Geophysical logs were examined with available core material to describe basalt, sediment and sedimentary rock layers, and rhyolite. Natural gamma logs were used to confirm sediment layer thickness and location; neutron logs were used to examine basalt flow units and changes in hydrogen content; gamma-gamma density logs were used to describe general changes in rock properties; and temperature logs were used to understand hydraulic gradients for deeper sections of borehole USGS 142. Gyroscopic deviation was measured to record deviation from true vertical at all depths in boreholes USGS 142 and USGS 142A.

Quantification of pore size distribution in reservoir rocks using MRI logging: A case study of South Pars Gas Field.

Science.gov (United States)

Ghojogh, Jalal Neshat; Esmaili, Mohammad; Noruzi-Masir, Behrooz; Bakhshi, Puyan

2017-12-01

Pore size distribution (PSD) is an important factor for controlling fluid transport through porous media. The study of PSD can be applicable in areas such as hydrocarbon storage, contaminant transport, prediction of multiphase flow, and analysis of the formation damage by mud infiltration. Nitrogen adsorption, centrifugation method, mercury injection, and X-ray computed tomography are commonly used to measure the distribution of pores. A core sample is occasionally not available because of the unconsolidated nature of reservoirs, high cost of coring operation, and program limitations. Magnetic resonance imaging logging (MRIL) is a proper logging technique that allows the direct measurement of the relaxation time of protons in pore fluids and correlating T 2 distribution to PSD using proper mathematical equations. It is nondestructive and fast and does not require core samples. In this paper, 8 core samples collected from the Dalan reservoir in South Pars Gas Field were studied by processing MRIL data and comparing them by PSD determined in the laboratory. By using the MRIL method, variation in PSD corresponding to the depth for the entire logged interval was determined. Moreover, a detailed mineralogical composition of the reservoir samples related to T 2 distribution was obtained. A good correlation between MRIL and mercury injection data was observed. High degree of similarity was also observed between T 2 distribution and PSD (R 2 = 0.85 to 0.91). Based on the findings from the MRIL method, the obtained values for clay bond water varied between 1E-6 and 1E-3µm, a range that is comprehended from an extra peak on the PSD curve. The frequent pore radius was determined to be 1µm. Copyright © 2017 Elsevier Ltd. All rights reserved.

ADN* Density log estimation Using Rockcell*

International Nuclear Information System (INIS)

Okuku, C.; Iloghalu, Emeka. M.; Omotayo, O.

2003-01-01

This work is intended to inform on the possibilities of estimating good density data in zones associated with sliding in a reservoir with ADN* tool with or without ADOS in string in cases where repeat sections were not done, possibly due to hole stability or directional concerns. This procedure has been equally used to obtain a better density data in corkscrew holes. Density data (ROBB) was recomputed using neural network in RockCell* to estimate the density over zones of interest. RockCell* is a Schlumberger software that has neural network functionally which can be used to estimate missing logs using the combination of the responses of other log curves and intervals that are not affected by sliding. In this work, an interval was selected and within this interval twelve litho zones were defined using the unsupervised neural network. From this a training set was selected based on intervals of very good log responses outside the sliding zones. This training set was used to train and run the neural network for a specific lithostratigraphic interval. The results matched the known good density curve. Then after this, an estimation of the density curve was done using the supervised neural network. The output from this estimation matched very closely in the good portions of the log, thus providing some density measurements in the sliding zone. This methodology provides a scientific solution to missing data during the process of Formation evaluation

Advances in Radiocarbon Measurement of Water Samples

Energy Technology Data Exchange (ETDEWEB)

Janovics, R.; Molnar, M.; Major, I. [Institute of Nuclear Research (ATO MKI), Hungarian Academy of Sciences, H-4001 Debrecen (Hungary); Svetlik, I. [Department of Radiation Dosimetry, Nuclear Physics Institute AS CR, Prague (Czech Republic); Wacker, L. [Institute for Particle Physics, ETH Hoenggerberg, Zuerich (Switzerland)

2013-07-15

In this paper two very different and novel methods for the {sup 14}C measurement of water samples are presented. The first method uses direct absorption into a scintillation cocktail and a following liquid scintillation measurement. Typical sample size is 20-40 L and overall uncertainty is {+-} 2% for modern samples. It is a very cost effective and easy to use method based on a novel and simple static absorption process for the CO{sub 2} extracted from groundwater. The other very sensitive method is based on accelerator mass spectrometry (AMS) using a gas ion source. With a MICADAS type AMS system we demonstrated that you can routinely measure the {sup 14}C content of 1 mL of water sample with better than 1% precision (for a modern sample). This direct {sup 14}C AMS measurement of water takes less than 20 minutes including sample preparation. (author)

Coarse woody debris in undisturbed and logged forests in the eastern Brazilian Amazon.

Science.gov (United States)

Michael Keller; Michael Palace; Gregory P. Asner; Rodrigo Jr. Pereira; Jose Natalino M. Silva

2004-01-01

Coarse woody debris (CWD) is an important component of the carbon cycle in tropical forests. We measured the volume and density of fallen CWD at two sites, Cauaxi and Tapajós in the Eastern Amazon. At both sites we studied undisturbed forests (UFs) and logged forests 1 year after harvest. Conventional logging (CL) and reduced impact logging (RIL) were...

A Hierarchical Poisson Log-Normal Model for Network Inference from RNA Sequencing Data

Science.gov (United States)

Gallopin, Mélina; Rau, Andrea; Jaffrézic, Florence

2013-01-01

Gene network inference from transcriptomic data is an important methodological challenge and a key aspect of systems biology. Although several methods have been proposed to infer networks from microarray data, there is a need for inference methods able to model RNA-seq data, which are count-based and highly variable. In this work we propose a hierarchical Poisson log-normal model with a Lasso penalty to infer gene networks from RNA-seq data; this model has the advantage of directly modelling discrete data and accounting for inter-sample variance larger than the sample mean. Using real microRNA-seq data from breast cancer tumors and simulations, we compare this method to a regularized Gaussian graphical model on log-transformed data, and a Poisson log-linear graphical model with a Lasso penalty on power-transformed data. For data simulated with large inter-sample dispersion, the proposed model performs better than the other methods in terms of sensitivity, specificity and area under the ROC curve. These results show the necessity of methods specifically designed for gene network inference from RNA-seq data. PMID:24147011

Life cycle performances of log wood applied for soil bioengineering constructions

Science.gov (United States)

Kalny, Gerda; Strauss-Sieberth, Alexandra; Strauss, Alfred; Rauch, Hans Peter

2016-04-01

Nowadays there is a high demand on engineering solutions considering not only technical aspects but also ecological and aesthetic values. Soil bioengineering is a construction technique that uses biological components for hydraulic and civil engineering solutions. Soil bioengineering solutions are based on the application of living plants and other auxiliary materials including among others log wood. This kind of construction material supports the soil bioengineering system as long as the plants as living construction material overtake the stability function. Therefore it is important to know about the durability and the degradation process of the wooden logs to retain the integral performance of a soil bio engineering system. These aspects will be considered within the framework of the interdisciplinary research project „ELWIRA Plants, wood, steel and concrete - life cycle performances as construction materials". Therefore field investigations on soil bioengineering construction material, specifically European Larch wood logs, of different soil bioengineering structures at the river Wien have been conducted. The drilling resistance as a parameter for particular material characteristics of selected logs was measured and analysed. The drilling resistance was measured with a Rinntech Resistograph instrument at different positions of the wooden logs, all surrounded with three different backfills: Fully surrounded with air, with earth contact on one side and near the water surface in wet-dry conditions. The age of the used logs ranges from one year old up to 20 year old. Results show progress of the drilling resistance throughout the whole cross section as an indicator to assess soil bioengineering construction material. Logs surrounded by air showed a higher drilling resistance than logs with earth contact and the ones exposed to wet-dry conditions. Hence the functional capability of wooden logs were analysed and discussed in terms of different levels of degradation

powerbox: Arbitrarily structured, arbitrary-dimension boxes and log-normal mocks

Science.gov (United States)

Murray, Steven G.

2018-05-01

powerbox creates density grids (or boxes) with an arbitrary two-point distribution (i.e. power spectrum). The software works in any number of dimensions, creates Gaussian or Log-Normal fields, and measures power spectra of output fields to ensure consistency. The primary motivation for creating the code was the simple creation of log-normal mock galaxy distributions, but the methodology can be used for other applications.

Particulate emissions from the combustion of birch, beech, and spruce logs cause different cytotoxic responses in A549 cells.

Science.gov (United States)

Kasurinen, Stefanie; Jalava, Pasi I; Happo, Mikko S; Sippula, Olli; Uski, Oskari; Koponen, Hanna; Orasche, Jürgen; Zimmermann, Ralf; Jokiniemi, Jorma; Hirvonen, Maija-Riitta

2017-05-01

According to the World Health Organization particulate emissions from the combustion of solid fuels caused more than 110,000 premature deaths worldwide in 2010. Log wood combustion is the most prevalent form of residential biomass heating in developed countries, but it is unknown how the type of wood logs used in furnaces influences the chemical composition of the particulate emissions and their toxicological potential. We burned logs of birch, beech and spruce, which are used commonly as firewood in Central and Northern Europe in a modern masonry heater, and compared them to the particulate emissions from an automated pellet boiler fired with softwood pellets. We determined the chemical composition (elements, ions, and carbonaceous compounds) of the particulate emissions with a diameter of less than 1 µm and tested their cytotoxicity, genotoxicity, inflammatory potential, and ability to induce oxidative stress in a human lung epithelial cell line. The chemical composition of the samples differed significantly, especially with regard to the carbonaceous and metal contents. Also the toxic effects in our tested endpoints varied considerably between each of the three log wood combustion samples, as well as between the log wood combustion samples and the pellet combustion sample. The difference in the toxicological potential of the samples in the various endpoints indicates the involvement of different pathways of toxicity depending on the chemical composition. All three emission samples from the log wood combustions were considerably more toxic in all endpoints than the emissions from the pellet combustion. © 2016 Wiley Periodicals, Inc. Environ Toxicol 32: 1487-1499, 2017. © 2016 Wiley Periodicals, Inc.

A Measuring System for Well Logging Attitude and a Method of Sensor Calibration

Directory of Open Access Journals (Sweden)

Yong Ren

2014-05-01

Full Text Available This paper proposes an approach for measuring the azimuth angle and tilt angle of underground drilling tools with a MEMS three-axis accelerometer and a three-axis fluxgate sensor. A mathematical model of well logging attitude angle is deduced based on combining space coordinate transformations and algebraic equations. In addition, a system implementation plan of the inclinometer is given in this paper, which features low cost, small volume and integration. Aiming at the sensor and assembly errors, this paper analyses the sources of errors, and establishes two mathematical models of errors and calculates related parameters to achieve sensor calibration. The results show that this scheme can obtain a stable and high precision azimuth angle and tilt angle of drilling tools, with the deviation of the former less than ±1.4° and the deviation of the latter less than ±0.1°.

A measuring system for well logging attitude and a method of sensor calibration.

Science.gov (United States)

Ren, Yong; Wang, Yangdong; Wang, Mijian; Wu, Sheng; Wei, Biao

2014-05-23

This paper proposes an approach for measuring the azimuth angle and tilt angle of underground drilling tools with a MEMS three-axis accelerometer and a three-axis fluxgate sensor. A mathematical model of well logging attitude angle is deduced based on combining space coordinate transformations and algebraic equations. In addition, a system implementation plan of the inclinometer is given in this paper, which features low cost, small volume and integration. Aiming at the sensor and assembly errors, this paper analyses the sources of errors, and establishes two mathematical models of errors and calculates related parameters to achieve sensor calibration. The results show that this scheme can obtain a stable and high precision azimuth angle and tilt angle of drilling tools, with the deviation of the former less than ±1.4° and the deviation of the latter less than ±0.1°.

Log4J

CERN Document Server

Perry, Steven

2009-01-01

Log4j has been around for a while now, and it seems like so many applications use it. I've used it in my applications for years now, and I'll bet you have too. But every time I need to do something with log4j I've never done before I find myself searching for examples of how to do whatever that is, and I don't usually have much luck. I believe the reason for this is that there is a not a great deal of useful information about log4j, either in print or on the Internet. The information is too simple to be of real-world use, too complicated to be distilled quickly (which is what most developers

Generating log-normal mock catalog of galaxies in redshift space

Energy Technology Data Exchange (ETDEWEB)

Agrawal, Aniket; Makiya, Ryu; Saito, Shun; Komatsu, Eiichiro [Max-Planck-Institut für Astrophysik, Karl-Schwarzschild-Str. 1, 85741 Garching (Germany); Chiang, Chi-Ting [C.N. Yang Institute for Theoretical Physics, Department of Physics and Astronomy, Stony Brook University, Stony Brook, NY 11794 (United States); Jeong, Donghui, E-mail: aniket@mpa-garching.mpg.de, E-mail: makiya@mpa-garching.mpg.de, E-mail: chi-ting.chiang@stonybrook.edu, E-mail: djeong@psu.edu, E-mail: ssaito@mpa-garching.mpg.de, E-mail: komatsu@mpa-garching.mpg.de [Department of Astronomy and Astrophysics, The Pennsylvania State University, University Park, PA 16802 (United States)

2017-10-01

We present a public code to generate a mock galaxy catalog in redshift space assuming a log-normal probability density function (PDF) of galaxy and matter density fields. We draw galaxies by Poisson-sampling the log-normal field, and calculate the velocity field from the linearised continuity equation of matter fields, assuming zero vorticity. This procedure yields a PDF of the pairwise velocity fields that is qualitatively similar to that of N-body simulations. We check fidelity of the catalog, showing that the measured two-point correlation function and power spectrum in real space agree with the input precisely. We find that a linear bias relation in the power spectrum does not guarantee a linear bias relation in the density contrasts, leading to a cross-correlation coefficient of matter and galaxies deviating from unity on small scales. We also find that linearising the Jacobian of the real-to-redshift space mapping provides a poor model for the two-point statistics in redshift space. That is, non-linear redshift-space distortion is dominated by non-linearity in the Jacobian. The power spectrum in redshift space shows a damping on small scales that is qualitatively similar to that of the well-known Fingers-of-God (FoG) effect due to random velocities, except that the log-normal mock does not include random velocities. This damping is a consequence of non-linearity in the Jacobian, and thus attributing the damping of the power spectrum solely to FoG, as commonly done in the literature, is misleading.

SU-E-T-184: Clinical VMAT QA Practice Using LINAC Delivery Log Files

International Nuclear Information System (INIS)

Johnston, H; Jacobson, T; Gu, X; Jiang, S; Stojadinovic, S

2015-01-01

Purpose: To evaluate the accuracy of volumetric modulated arc therapy (VMAT) treatment delivery dose clouds by comparing linac log data to doses measured using an ionization chamber and film. Methods: A commercial IMRT quality assurance (QA) process utilizing a DICOM-RT framework was tested for clinical practice using 30 prostate and 30 head and neck VMAT plans. Delivered 3D VMAT dose distributions were independently checked using a PinPoint ionization chamber and radiographic film in a solid water phantom. DICOM RT coordinates were used to extract the corresponding point and planar doses from 3D log file dose distributions. Point doses were evaluated by computing the percent error between log file and chamber measured values. A planar dose evaluation was performed for each plan using a 2D gamma analysis with 3% global dose difference and 3 mm isodose point distance criteria. The same analysis was performed to compare treatment planning system (TPS) doses to measured values to establish a baseline assessment of agreement. Results: The mean percent error between log file and ionization chamber dose was 1.0%±2.1% for prostate VMAT plans and −0.2%±1.4% for head and neck plans. The corresponding TPS calculated and measured ionization chamber values agree within 1.7%±1.6%. The average 2D gamma passing rates for the log file comparison to film are 98.8%±1.0% and 96.2%±4.2% for the prostate and head and neck plans, respectively. The corresponding passing rates for the TPS comparison to film are 99.4%±0.5% and 93.9%±5.1%. Overall, the point dose and film data indicate that log file determined doses are in excellent agreement with measured values. Conclusion: Clinical VMAT QA practice using LINAC treatment log files is a fast and reliable method for patient-specific plan evaluation

Catching errors with patient-specific pretreatment machine log file analysis.

Science.gov (United States)

Rangaraj, Dharanipathy; Zhu, Mingyao; Yang, Deshan; Palaniswaamy, Geethpriya; Yaddanapudi, Sridhar; Wooten, Omar H; Brame, Scott; Mutic, Sasa

2013-01-01

A robust, efficient, and reliable quality assurance (QA) process is highly desired for modern external beam radiation therapy treatments. Here, we report the results of a semiautomatic, pretreatment, patient-specific QA process based on dynamic machine log file analysis clinically implemented for intensity modulated radiation therapy (IMRT) treatments delivered by high energy linear accelerators (Varian 2100/2300 EX, Trilogy, iX-D, Varian Medical Systems Inc, Palo Alto, CA). The multileaf collimator machine (MLC) log files are called Dynalog by Varian. Using an in-house developed computer program called "Dynalog QA," we automatically compare the beam delivery parameters in the log files that are generated during pretreatment point dose verification measurements, with the treatment plan to determine any discrepancies in IMRT deliveries. Fluence maps are constructed and compared between the delivered and planned beams. Since clinical introduction in June 2009, 912 machine log file analyses QA were performed by the end of 2010. Among these, 14 errors causing dosimetric deviation were detected and required further investigation and intervention. These errors were the result of human operating mistakes, flawed treatment planning, and data modification during plan file transfer. Minor errors were also reported in 174 other log file analyses, some of which stemmed from false positives and unreliable results; the origins of these are discussed herein. It has been demonstrated that the machine log file analysis is a robust, efficient, and reliable QA process capable of detecting errors originating from human mistakes, flawed planning, and data transfer problems. The possibility of detecting these errors is low using point and planar dosimetric measurements. Copyright © 2013 American Society for Radiation Oncology. Published by Elsevier Inc. All rights reserved.

Unsupervised signature extraction from forensic logs

NARCIS (Netherlands)

Thaler, S.M.; Menkovski, V.; Petkovic, M.; Altun, Y.; Das, K.; Mielikäinen, T.; Malerba, D.; Stefanowski, J.; Read, J.; Žitnik, M.; Ceci, M.

2017-01-01

Signature extraction is a key part of forensic log analysis. It involves recognizing patterns in log lines such that log lines that originated from the same line of code are grouped together. A log signature consists of immutable parts and mutable parts. The immutable parts define the signature, and

Response diversity, functional redundancy, and post-logging productivity in northern temperate and boreal forests.

Science.gov (United States)

Correia, David Laginha Pinto; Raulier, Frédéric; Bouchard, Mathieu; Filotas, Élise

2018-04-19

The development of efficient ecosystem resilience indicators was identified as one of the key research priorities in the improvement of existing sustainable forest management frameworks. Two indicators of tree diversity associated with ecosystem functioning have recently received particular attention in the literature: functional redundancy (FR) and response diversity (RD). We examined how these indicators could be used to predict post-logging productivity in forests of Québec, Canada. We analysed the relationships between pre-logging FR and RD, as measured with sample plots, and post-logging productivity, measured as seasonal variation in enhanced vegetation index obtained from MODIS satellite imagery. The effects of the deciduous and coniferous tree components in our pre-disturbance diversity assessments were isolated in order to examine the hypothesis that they have different impacts on post-disturbance productivity. We also examined the role of tree species richness and species identity effects. Our analysis revealed the complementary nature of traditional biodiversity indicators and trait-based approaches in the study of biodiversity-ecosystem-functioning relationships in dynamic ecosystems. We report a significant and positive relationship between pre-disturbance deciduous RD and post-disturbance productivity, as well as an unexpected significant negative effect of coniferous RD on productivity. This negative relationship with post-logging productivity likely results from slower coniferous regeneration speeds and from the relatively short temporal scale examined. Negative black-spruce-mediated identity effects were likely associated with increased stand vulnerability to paludification and invasion by ericaceous shrubs that slow down forest regeneration. Response diversity outperformed functional redundancy as a measure of post-disturbance productivity most likely due to the stand-replacing nature of the disturbance considered. To the best of our knowledge

Log-balanced combinatorial sequences

Directory of Open Access Journals (Sweden)

Tomislav Došlic

2005-01-01

Full Text Available We consider log-convex sequences that satisfy an additional constraint imposed on their rate of growth. We call such sequences log-balanced. It is shown that all such sequences satisfy a pair of double inequalities. Sufficient conditions for log-balancedness are given for the case when the sequence satisfies a two- (or more- term linear recurrence. It is shown that many combinatorially interesting sequences belong to this class, and, as a consequence, that the above-mentioned double inequalities are valid for all of them.

Computation of porosity and water content from geophysical logs, Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Nelson, P.H.

1996-01-01

Neutron and density logs acquired in boreholes at Yucca Mountain, Nevada are used to determine porosity and water content as a function of depth. Computation of porosity requires an estimate of grain density, which is provided by core data, mineralogical data, or is inferred from rock type where neither core nor mineralogy are available. The porosity estimate is merged with mineralogical data acquired by X-ray diffraction to compute the volumetric fractions of major mineral groups. The resulting depth-based portrayal of bulk rock composition is equivalent to a whole rock analysis of mineralogy and porosity. Water content is computed from epithermal and thermal neutron logs. In the unsaturated zone, the density log is required along with a neutron log. Water content can also be computed from dielectric logs, which were acquired in only a fraction of the boreholes, whereas neutron logs were acquired in all boreholes. Mineralogical data are used to compute a structural (or bound) water estimate, which is subtracted from the total water estimate from the neutron-density combination. Structural water can be subtracted only from intervals where mineralogical analyses are available; otherwise only total water can be reported. The algorithms and procedures are applied to logs acquired during 1979 to 1984 at Yucca Mountain. Examples illustrate the results. Comparison between computed porosity and core measurements shows systematic differences ranging from 0.005 to 0.04. These values are consistent with a sensitivity analysis using uncertainty parameters for good logging conditions. Water content from core measurements is available in only one borehole, yielding a difference between computed and core-based water content of 0.006

LOG2MARKUP: State module to transform a Stata text log into a markup document

DEFF Research Database (Denmark)

2016-01-01

log2markup extract parts of the text version from the Stata log command and transform the logfile into a markup based document with the same name, but with extension markup (or otherwise specified in option extension) instead of log. The author usually uses markdown for writing documents. However...

Selective‐logging and oil palm: multitaxon impacts, biodiversity indicators, and trade‐offs for conservation planning.

Science.gov (United States)

Edwards, David P; Magrach, Ainhoa; Woodcock, Paul; Ji, Yinqiu; Lim, Norman T -L; Edwards, Felicity A; Larsen, Trond H; Hsu, Wayne W; Benedick, Suzan; Khen, Chey Vun; Chung, Arthur Y C; Reynolds, Glen; Fisher, Brendan; Laurance, William F; Wilcove, David S; Hamer, Keith C; Yu, Douglas W

Strong global demand for tropical timber and agricultural products has driven large-scale logging and subsequent conversion of tropical forests. Given that the majority of tropical landscapes have been or will likely be logged, the protection of biodiversity within tropical forests thus depends on whether species can persist in these economically exploited lands, and if species cannot persist, whether we can protect enough primary forest from logging and conversion. However, our knowledge of the impact of logging and conversion on biodiversity is limited to a few taxa, often sampled in different locations with complex land-use histories, hampering attempts to plan cost-effective conservation strategies and to draw conclusions across taxa. Spanning a land-use gradient of primary forest, once- and twice-logged forests, and oil palm plantations, we used traditional sampling and DNA metabarcoding to compile an extensive data set in Sabah, Malaysian Borneo for nine vertebrate and invertebrate taxa to quantify the biological impacts of logging and oil palm, develop cost-effective methods of protecting biodiversity, and examine whether there is congruence in response among taxa. Logged forests retained high species richness, including, on average, 70% of species found in primary forest. In contrast, conversion to oil palm dramatically reduces species richness, with significantly fewer primary-forest species than found on logged forest transects for seven taxa. Using a systematic conservation planning analysis, we show that efficient protection of primary-forest species is achieved with land portfolios that include a large proportion of logged-forest plots. Protecting logged forests is thus a cost-effective method of protecting an ecologically and taxonomically diverse range of species, particularly when conservation budgets are limited. Six indicator groups (birds, leaf-litter ants, beetles, aerial hymenopterans, flies, and true bugs) proved to be consistently good

Dual excitation acoustic paramagnetic logging tool

Energy Technology Data Exchange (ETDEWEB)

Vail, III, William B. (Bothell, WA)

1989-01-01

New methods and apparatus are disclosed which allow measurement of the presence of oil and water in gelogical formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleous present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described.

Simultaneous thermal neutron decay time and porosity logging system

International Nuclear Information System (INIS)

Schultz, W.E.; Smith, H.D.; Smith, M.P.

1980-01-01

An improved method and apparatus are described for simultaneously measuring the porosity and thermal neutron capture cross section of earth formations in situ in the vicinity of a well borehole using pulsed neutron well logging techniques. The logging tool which is moved through the borehole consists of a 14 MeV pulsed neutron source, an epithermal neutron detector and a combination gamma ray and fast neutron detector. The associated gating systems, counters and combined digital computer are sited above ground. (U.K.)

Automatic Data Logging and Quality Analysis System for Mobile Devices

Directory of Open Access Journals (Sweden)

Yong-Yi Fanjiang

2017-01-01

Full Text Available The testing phase of mobile device products includes two important test projects that must be completed before shipment: the field trial and the beta user trial. During the field trial, the product is certified based on its integration and stability with the local operator’s system, and, during the beta user trial, the product is certified by multiple users regarding its daily use, where the goal is to detect and solve early problems. In the traditional approach used to issue returns, testers must log into a web site, fill out a problem form, and then go through a browser or FTP to upload logs; however, this is inconvenient, and problems are reported slowly. Therefore, we propose an “automatic logging analysis system” (ALAS to construct a convenient test environment and, using a record analysis (log parser program, automate the parsing of log files and have questions automatically sent to the database by the system. Finally, the mean time between failures (MTBF is used to establish measurement indicators for the beta user trial.

LOG-NORMAL DISTRIBUTION OF COSMIC VOIDS IN SIMULATIONS AND MOCKS

Energy Technology Data Exchange (ETDEWEB)

Russell, E.; Pycke, J.-R., E-mail: er111@nyu.edu, E-mail: jrp15@nyu.edu [Division of Science and Mathematics, New York University Abu Dhabi, P.O. Box 129188, Abu Dhabi (United Arab Emirates)

2017-01-20

Following up on previous studies, we complete here a full analysis of the void size distributions of the Cosmic Void Catalog based on three different simulation and mock catalogs: dark matter (DM), haloes, and galaxies. Based on this analysis, we attempt to answer two questions: Is a three-parameter log-normal distribution a good candidate to satisfy the void size distributions obtained from different types of environments? Is there a direct relation between the shape parameters of the void size distribution and the environmental effects? In an attempt to answer these questions, we find here that all void size distributions of these data samples satisfy the three-parameter log-normal distribution whether the environment is dominated by DM, haloes, or galaxies. In addition, the shape parameters of the three-parameter log-normal void size distribution seem highly affected by environment, particularly existing substructures. Therefore, we show two quantitative relations given by linear equations between the skewness and the maximum tree depth, and between the variance of the void size distribution and the maximum tree depth, directly from the simulated data. In addition to this, we find that the percentage of voids with nonzero central density in the data sets has a critical importance. If the number of voids with nonzero central density reaches ≥3.84% in a simulation/mock sample, then a second population is observed in the void size distributions. This second population emerges as a second peak in the log-normal void size distribution at larger radius.

Log-based identification of sweet spots for effective fracs in shale reservoirs

Energy Technology Data Exchange (ETDEWEB)

Hashmy, K.; Barnett, C.; Jonkers, J. [Weatherford (United States); Abueita, S. [Anadarko Petroleum (United States)

2011-07-01

Shale reservoir exploitation requires horizontal hydro-fracturing, often in a multi-stage configuration. Fracture stages are usually evenly spaced along the horizontal well, regardless of reservoir characteristics, even though wireline logs or logging-while-drilling (LWD) methods could be used to determine sweet spots for more cost-effective fracturing locations. This paper aims to show how failure to take into consideration a reservoir's geological properties can lead to less effective exploitation, and then goes on to describe logging techniques, LWD and wireline logs combined, and their usefulness in effectively placing fracturing stages on a reservoir's sweet spots. By studying logs from different LWD and wireline log techniques, such as gamma ray, resistivity, X-ray fluorescence or shockwave sonic measurements for different existing wells, the study shows how sweet spots, where kerogen concentration is higher, with higher porosity, can be determined. These logging techniques, requiring low investments, offer a variety of methods for identifying sweet spots in shale reservoirs, and fracturing only these spots will avoid unnecessary expenditure on frac stages in zones with poor reservoir characteristics.

Hardwood log supply: a broader perspective

Science.gov (United States)

Iris Montague; Adri Andersch; Jan Wiedenbeck; Urs. Buehlmann

2015-01-01

At regional and state meetings we talk with others in our business about the problems we face: log exports, log quality, log markets, logger shortages, cash flow problems, the weather. These are familiar talking points and real and persistent problems. But what is the relative importance of these problems for log procurement in different regions of...

Drilling and associated drillhole measurements of the pilot hole ONK-PH11

International Nuclear Information System (INIS)

Karttunen, P.; Mancini, P.; Pekkanen, J.; Poellaenen, J.; Tarvainen, A.-M.; Toropainen, V.; Pere, T.

2011-01-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH11 was drilled from chainage 3922 to chainage 4053 in October 2009. The length of the hole is 131.21 metres. The aim during the drilling work was to orient core samples as much as possible. The deviation of the drillhole was measured during and after the drilling phase. Electric conductivity was measured from the collected returning water samples. Hydraulic conductivity of the fractures or fractured zones was measured by Posiva Flow Log equipment. During flow measurements also electric conductivity and temperature were measured. In flow logging test sections of 0.5 m and increments of 0.1 m were used. The water loss measurements were performed after drilling was completed by the drilling company. Logging of the core samples included the following parameters: lithology, foliation, fracturing, RQD, fractured zones, weathering and possible intersections. The rock mechanical logging was based on Q-classification. The rock strength and deformation were determined with Rock Tester -equipment. Geophysical logging and optical imaging of the pilot hole included the fieldwork of all surveys, the integration of the data as well as interpretation of the acoustic and drillhole radar data. The groundwater samples were collected from the open hole without any packers. The collected groundwater samples were

Effect of Logging Activities on Water Quality and Benthic ...

African Journals Online (AJOL)

The study was conducted to determine the effect of logging activities on water quality and benthic macroinvertebrate assemblages for the Madek River basin. The study area was situated in Kluang, Johor, Malaysia. Two sampling stations 500 meters apart are upstream and the other, downstream located at Madek River ...

Semi-automatic logarithmic converter of logs

International Nuclear Information System (INIS)

Gol'dman, Z.A.; Bondar's, V.V.

1974-01-01

Semi-automatic logarithmic converter of logging charts. An original semi-automatic converter was developed for use in converting BK resistance logging charts and the time interval, ΔT, of acoustic logs from a linear to a logarithmic scale with a specific ratio for subsequent combining of them with neutron-gamma logging charts in operative interpretation of logging materials by a normalization method. The converter can be used to increase productivity by giving curves different from those obtained in manual, pointwise processing. The equipment operates reliably and is simple in use. (author)

Power to the logs!

CERN Multimedia

CERN. Geneva; MACMAHON, Joseph

2015-01-01

Are you tired of using grep, vi and emacs to read your logs? Do you feel like you’re missing the big picture? Does the word "statistics" put a smile on your face? Then it’s time to give power to the logs!

Accuracy and borehole influences in pulsed neutron gamma density logging while drilling

Energy Technology Data Exchange (ETDEWEB)

Yu Huawei [College of Geo-Resources and Information, China University of Petroleum, Qingdao, Shandong 266555 (China); Center for Engineering Applications of Radioisotopes (CEAR), Department of Nuclear Engineering, North Carolina State University, Raleigh, NC 27695 (United States); Sun Jianmeng [College of Geo-Resources and Information, China University of Petroleum, Qingdao, Shandong 266555 (China); Wang Jiaxin [Center for Engineering Applications of Radioisotopes (CEAR), Department of Nuclear Engineering, North Carolina State University, Raleigh, NC 27695 (United States); Gardner, Robin P., E-mail: gardner@ncsu.edu [Center for Engineering Applications of Radioisotopes (CEAR), Department of Nuclear Engineering, North Carolina State University, Raleigh, NC 27695 (United States)

2011-09-15

A new pulsed neutron gamma density (NGD) logging has been developed to replace radioactive chemical sources in oil logging tools. The present paper describes studies of near and far density measurement accuracy of NGD logging at two spacings and the borehole influences using Monte-Carlo simulation. The results show that the accuracy of near density is not as good as far density. It is difficult to correct this for borehole effects by using conventional methods because both near and far density measurement is significantly sensitive to standoffs and mud properties. - Highlights: > Monte Carlo evaluation of pulsed neutron gamma-ray density tools. > Results indicate sensitivity of the tool to standoff and mudcake properties. > Accuracy of far spaced detector is better than near spaced.

Accuracy and borehole influences in pulsed neutron gamma density logging while drilling

International Nuclear Information System (INIS)

Yu Huawei; Sun Jianmeng; Wang Jiaxin; Gardner, Robin P.

2011-01-01

A new pulsed neutron gamma density (NGD) logging has been developed to replace radioactive chemical sources in oil logging tools. The present paper describes studies of near and far density measurement accuracy of NGD logging at two spacings and the borehole influences using Monte-Carlo simulation. The results show that the accuracy of near density is not as good as far density. It is difficult to correct this for borehole effects by using conventional methods because both near and far density measurement is significantly sensitive to standoffs and mud properties. - Highlights: → Monte Carlo evaluation of pulsed neutron gamma-ray density tools. → Results indicate sensitivity of the tool to standoff and mudcake properties. → Accuracy of far spaced detector is better than near spaced.

California-Nevada uranium logging. Final report

International Nuclear Information System (INIS)

1981-04-01

The purpose of this project was to obtain geophysical logs of industry drill holes to assess the uranium resource potential of geologic formations of interest. The work was part of the US Department of Energy's National Uranium Resource Evaluation (NURE) Program. The principal objective of the logging program was to determine radioelement grade of formations through natural gamma ray detectors. Supplementary information was obtained from resistivity (R), self-potential (SP), point resistance (RE), and neutron density (NN) logs for formation interpretation. Additional data for log interpretation was obtained from caliper logs, casing schedules, and downhole temperature. This data was obtained from well operators when available, with new logs obtained where not formerly available. This report contains a summary of the project and data obtained to date

[Using log-binomial model for estimating the prevalence ratio].

Science.gov (United States)

Ye, Rong; Gao, Yan-hui; Yang, Yi; Chen, Yue

2010-05-01

To estimate the prevalence ratios, using a log-binomial model with or without continuous covariates. Prevalence ratios for individuals' attitude towards smoking-ban legislation associated with smoking status, estimated by using a log-binomial model were compared with odds ratios estimated by logistic regression model. In the log-binomial modeling, maximum likelihood method was used when there were no continuous covariates and COPY approach was used if the model did not converge, for example due to the existence of continuous covariates. We examined the association between individuals' attitude towards smoking-ban legislation and smoking status in men and women. Prevalence ratio and odds ratio estimation provided similar results for the association in women since smoking was not common. In men however, the odds ratio estimates were markedly larger than the prevalence ratios due to a higher prevalence of outcome. The log-binomial model did not converge when age was included as a continuous covariate and COPY method was used to deal with the situation. All analysis was performed by SAS. Prevalence ratio seemed to better measure the association than odds ratio when prevalence is high. SAS programs were provided to calculate the prevalence ratios with or without continuous covariates in the log-binomial regression analysis.

Intelligent sampling for the measurement of structured surfaces

International Nuclear Information System (INIS)

Wang, J; Jiang, X; Blunt, L A; Scott, P J; Leach, R K

2012-01-01

Uniform sampling in metrology has known drawbacks such as coherent spectral aliasing and a lack of efficiency in terms of measuring time and data storage. The requirement for intelligent sampling strategies has been outlined over recent years, particularly where the measurement of structured surfaces is concerned. Most of the present research on intelligent sampling has focused on dimensional metrology using coordinate-measuring machines with little reported on the area of surface metrology. In the research reported here, potential intelligent sampling strategies for surface topography measurement of structured surfaces are investigated by using numerical simulation and experimental verification. The methods include the jittered uniform method, low-discrepancy pattern sampling and several adaptive methods which originate from computer graphics, coordinate metrology and previous research by the authors. By combining the use of advanced reconstruction methods and feature-based characterization techniques, the measurement performance of the sampling methods is studied using case studies. The advantages, stability and feasibility of these techniques for practical measurements are discussed. (paper)

Some effects of logging and associated road construction on northern California streams

Science.gov (United States)

James W. Burns

1972-01-01

Abstract - The effects of logging and associated road construction on four California trout and salmon streams were investigated from 1966 through 1969. This study included measurements of streambed sedimentation, water quality, fish food abundance, and stream nursery capacity. Logging was found to be compatible with anadromous fish production when adequate attention...

Benefits of obtaining log data in horizontal wells in the WCSB

Energy Technology Data Exchange (ETDEWEB)

Spratt, D. [Reeves Wireline Technologies Ltd., Calgary, AB (Canada)

2001-11-01

A Compact Memory Logging (CML) system developed by Reeves Wireline Technologies was presented. It can be used to obtain log data from horizontal wells to get a better understanding of how to enhance production or completion techniques. The methods that are commonly used to obtain data from horizontal wells include measurement while drilling (MWD), logging while drilling (LWD), wet connect pipe conveyed wireline logging and CML. Each method has its unique benefits that range from information on lithology, rock parameters and fluid interfaces. Reeves has been using wireless pipe conveyed CML over the past two years. The log data includes array induction, dual spaced neutron and photo density porosity, Pe, gamma ray, compensated sonic and hose size caliper. Reeves CML is smaller, easily conveyed and has an unprecedented capability to bend and is considered to be well suited for both newly and previously drilled horizontal wells that require remedial assessment. The tool can be used to determine reservoir quality and boundaries, establish zone structures, or identify fluid interfaces for strategic planning of completions and stimulations. This paper presented examples of logs on some horizontal wells that indicate the value of obtaining log data. Reeves CML is considered to be economically and operationally ideal, particularly since data from the CML includes depth of investigation. 5 figs.

Inertial Navigation System/Doppler Velocity Log (INS/DVL Fusion with Partial DVL Measurements

Directory of Open Access Journals (Sweden)

Asaf Tal

2017-02-01

Full Text Available The Technion autonomous underwater vehicle (TAUV is an ongoing project aiming to develop and produce a small AUV to carry on research missions, including payload dropping, and to demonstrate acoustic communication. Its navigation system is based on an inertial navigation system (INS aided by a Doppler velocity log (DVL, magnetometer, and pressure sensor (PS. In many INSs, such as the one used in TAUV, only the velocity vector (provided by the DVL can be used for aiding the INS, i.e., enabling only a loosely coupled integration approach. In cases of partial DVL measurements, such as failure to maintain bottom lock, the DVL cannot estimate the vehicle velocity. Thus, in partial DVL situations no velocity data can be integrated into the TAUV INS, and as a result its navigation solution will drift in time. To circumvent that problem, we propose a DVL-based vehicle velocity solution using the measured partial raw data of the DVL and additional information, thereby deriving an extended loosely coupled (ELC approach. The implementation of the ELC approach requires only software modification. In addition, we present the TAUV six degrees of freedom (6DOF simulation that includes all functional subsystems. Using this simulation, the proposed approach is evaluated and the benefit of using it is shown.

Cause of depth error of borehole logging and its correction

International Nuclear Information System (INIS)

Iida, Yoshimasa; Ikeda, Koki; Tsuruta, Tadahiko; Ito, Hiroaki; Goto, Junichi.

1996-01-01

Data by borehole logging can be used for detailed analysis of geological structures. Depths measured by portable borehole loggers commonly shift a few meters on the level of 400 to 500 meters deep. Therefore, the cause of depth error has to be recognized to make proper corrections for detailed structural analysis. Correlation between depths of drill core and in-rod radiometric logging has been performed in detail on exploration drill holes in the Athabasca basin, Canada. As a result, a common tendency of logging depth shift has been recognized, and an empirical formula (quadratic equation) for this has been obtained. The physical meaning of the formula and the cause of the depth error has been considered. (author)

Borehole Calibration Facilities to Support Gamma Logging for Hanford Subsurface Investigation and Contaminant Monitoring - 13516

International Nuclear Information System (INIS)

McCain, R.G.; Henwood, P.D.; Pope, A.D.; Pearson, A.W.

2013-01-01

Repeated gamma logging in cased holes represents a cost-effective means to monitor gamma-emitting contamination in the deep vadose zone over time. Careful calibration and standardization of gamma log results are required to track changes and to compare results over time from different detectors and logging systems. This paper provides a summary description of Hanford facilities currently available for calibration of logging equipment. Ideally, all logging organizations conducting borehole gamma measurements at the Hanford Site will take advantage of these facilities to produce standardized and comparable results. (authors)

Borehole Calibration Facilities to Support Gamma Logging for Hanford Subsurface Investigation and Contaminant Monitoring - 13516

Energy Technology Data Exchange (ETDEWEB)

McCain, R.G.; Henwood, P.D.; Pope, A.D.; Pearson, A.W. [S M Stoller Corporation, 2439 Robertson Drive, Richland, WA 99354 (United States)

2013-07-01

Repeated gamma logging in cased holes represents a cost-effective means to monitor gamma-emitting contamination in the deep vadose zone over time. Careful calibration and standardization of gamma log results are required to track changes and to compare results over time from different detectors and logging systems. This paper provides a summary description of Hanford facilities currently available for calibration of logging equipment. Ideally, all logging organizations conducting borehole gamma measurements at the Hanford Site will take advantage of these facilities to produce standardized and comparable results. (authors)

E-log system in monitoring of residency program: trainees perspective

International Nuclear Information System (INIS)

Iqbal, U.; Gondal, K.M.

2015-01-01

To record residents perspective about the utility of newly introduced E-Log system at the College of Physicians and Surgeons Pakistan (CPSP). Study Design: Sequential mixed method design using survey questionnaire and in-depth interviews. Place and Duration of Study: CPSP, Regional Center, Lahore, from March to June 2014. Methodology: Data was collected from registered trainees through a web-based survey questionnaire on a scale of 1 to 7 about the utility of E-log system. In-depth interviews were conducted with 7 students using non-probability purposive sampling. The interviews were tape recorded and subsequently transcribed. Quantitative data was analyzed using SPSS version 20 and qualitative data was analyzed using content analysis by identifying themes and patterns. Results: A total of 4399 responses were received. Motivation was 4.61± 1.98; 4.33 ± 2.00 remained acknowledgment of control of one's training by the new system. Ease of use got a mean score of 4.56 ± 2.15. Conclusion: The overall acceptance of the students regarding E-Log system was high. Scheduling IT workshop at the start of training will add to the student satisfaction regarding utility of E-Log system. (author)

Observations from borehole dilution logging experiments in fractured crystalline rock under variable hydraulic conditions

Science.gov (United States)

Harte, Philip T.; Anderson, Alton; Williams, John H.

2014-01-01

Identifying hydraulically active fractures in low permeability, crystalline-bedrock aquifers requires a variety of geophysical and hydrogeophysical borehole tools and approaches. One such approach is Single Borehole Dilution Tests (SBDT), which in some low flow cases have been shown to provide greater resolution of borehole flow than other logging procedures, such as vertical differential Heat Pulse Flowmeter (HPFM) logging. Because the tools used in SBDT collect continuous profiles of water quality or dye changes, they can identify horizontal flow zones and vertical flow. We used SBDT with a food grade blue dye as a tracer and dual photometer-nephelometer measurements to identify low flow zones.SBDT were conducted at seven wells with open boreholes (exceeding 300 ft). At most of the wells HPFM logs were also collected. The seven wells are set in low-permeability, fractured granite and gneiss rocks underlying a former tetrachloroeythylene (PCE) source area at the Savage Municipal Well Superfund site in Milford, NH. Time series SBDT logs were collected at each of the seven wells under three distinct hydraulic conditions: (1) ambient conditions prior to a pump test at an adjacent well, (2) mid test, after 2-3 days of the start of the pump test, and (3) at the end of the test, after 8-9 days of the pump test. None of the SBDT were conducted under pumping conditions in the logged well. For each condition, wells were initially passively spiked with blue dye once and subsequent time series measurements were made.Measurement accuracy and precision of the photometer tool is important in SBDT when attempting to detect low rates of borehole flow. Tests indicate that under ambient conditions, none of the wells had detectable flow as measured with HPFM logging. With SBDT, 4 of the 7 showed the presence of some very low flow. None of 5 (2 of the 7 wells initially logged with HPFM under ambient conditions were not re-logged) wells logged with the HPFM during the pump test had

Methods and apparatus for environmental correction of thermal neutron logs

International Nuclear Information System (INIS)

Preeg, W.E.; Scott, H.D.

1983-01-01

An on-line environmentally-corrected measurement of the thermal neutron decay time (tau) of an earth formation traversed by a borehole is provided in a two-detector, pulsed neutron logging tool, by measuring tau at each detector and combining the two tau measurements in accordance with a previously established empirical relationship of the general form: tau = tausub(F) +A(tausub(F) + tausub(N)B) + C, where tausub(F) and tausub(N) are the tau measurements at the far-spaced and near-spaced detectors, respectively, A is a correction coefficient for borehole capture cross section effects, B is a correction coefficient for neutron diffusion effects, and C is a constant related to parameters of the logging tool. Preferred numerical values of A, B and C are disclosed, and a relationship for more accurately approximating the A term to specific borehole conditions. (author)

32 CFR 700.846 - Status of logs.

Science.gov (United States)

2010-07-01

... Officers Afloat § 700.846 Status of logs. The deck log, the engineering log, the compass record, the bearing hooks, the engineer's bell book, and any records generated by automated data logging equipment...

Does selective logging stress tropical forest invertebrates? Using fat stores to examine sublethal responses in dung beetles.

Science.gov (United States)

França, Filipe; Barlow, Jos; Araújo, Bárbara; Louzada, Julio

2016-12-01

The increased global demand for tropical timber has driven vast expanses of tropical forests to be selectively logged worldwide. While logging impacts on wildlife are predicted to change species distribution and abundance, the underlying physiological responses are poorly understood. Although there is a growing consensus that selective logging impacts on natural populations start with individual stress-induced sublethal responses, this literature is dominated by investigations conducted with vertebrates from temperate zones. Moreover, the sublethal effects of human-induced forest disturbance on tropical invertebrates have never been examined. To help address this knowledge gap, we examined the body fat content and relative abundance of three dung beetle species (Coleoptera: Scarabaeinae) with minimum abundance of 40 individuals within each examined treatment level. These were sampled across 34 plots in a before-after control-impact design (BACI) in a timber concession area of the Brazilian Amazon. For the first time, we present evidence of logging-induced physiological stress responses in tropical invertebrates. Selective logging increased the individual levels of fat storage and reduced the relative abundance of two dung beetle species. Given this qualitative similarity, we support the measurement of body fat content as reliable biomarker to assess stress-induced sublethal effects on dung beetles. Understanding how environmental modification impacts the wildlife has never been more important. Our novel approach provides new insights into the mechanisms through which forest disturbances impose population-level impacts on tropical invertebrates.

Palm distributions for log Gaussian Cox processes

DEFF Research Database (Denmark)

Coeurjolly, Jean-Francois; Møller, Jesper; Waagepetersen, Rasmus Plenge

2017-01-01

This paper establishes a remarkable result regarding Palm distributions for a log Gaussian Cox process: the reduced Palm distribution for a log Gaussian Cox process is itself a log Gaussian Cox process that only differs from the original log Gaussian Cox process in the intensity function. This new...... result is used to study functional summaries for log Gaussian Cox processes....

Systematic logging utilizing a log sheet designed for drill core descriptions. An example in uranium exploration activities

International Nuclear Information System (INIS)

Sasao, Eiji; Tsuruta, Tadahiko; Iida, Yoshimasa

2000-01-01

We describe the log sheets used during uranium exploration activities for unconformity-related uranium deposits by JNC. The purpose of using the logging sheets is to standardize the objects which all geologists must observe and for data quality assurance. The log sheets are a three-part set describing basement lithology, sandstone lithology and geotechnics. We devised our own log sheets to describe both the sandstone and the underlying basement rock when we started exploration in Athabasca Basin, Canada. We modified the sheets to gain a better understanding of the geological features related to uranium mineralization, and made final improvements to satisfy required quality based on the criteria of descriptive objects and accuracy. Use of the log sheets resulted in effective performance of core logging and improvement in the display of data. (author)

DOE-Grand Junction logging model data synopsis

International Nuclear Information System (INIS)

Mathews, M.A.; Koizumi, C.J.; Evans, H.B.

1978-05-01

This synopsis provides the available data concerning the logging models at the DoE-Grand Junction facility, to date (1976). Because gamma-ray logs are used in uranium exploration to estimate the grade (percent U 3 O 8 ) and the thickness of uranium ore zones in exploration drill holes, logging models are required to calibrate the gamma-ray logging equipment in order to obtain accuracy, uniformity, standardization, and repeatability during logging. This quality control is essential for accurate ore reserve calculations and for estimates of ore potential. The logging models at the DoE-Grand Junction facility are available for use by private industry in calibrating their gamma-ray logging equipment. 21 figures, 26 tables

SNG-logs at Skjern

DEFF Research Database (Denmark)

Korsbech, Uffe C C; Petersen, Jesper; Aage, Helle Karina

1998-01-01

Spectral Natural Gamma-ray logs have been run in two water supply borings at Skjern. The log data have been examined by a new technique - Noise Adjusted Singular Value Decomposition - in order to get a detailed and reliable picture of the distribution of uranium and thorium gamma-rays from heavy...

Measurement of neutron activation in concrete samples

International Nuclear Information System (INIS)

Zagar, T.; Ravnik, M.

2000-01-01

The results of activation studies of ordinary and barytes concrete samples relevant for research reactor decommissioning are given. Five important long-lived radioactive isotopes ( 54 Mn, 60 Co, 65 Zn, 133 Ba, and 152 Eu) were identified from the gamma-ray spectra measured in the irradiated concrete samples. Activation of these samples was also calculated using ORIGEN2 code. Comparison of calculated and measured results is given. (author)

Tritium sampling and measurement

International Nuclear Information System (INIS)

Wood, M.J.; McElroy, R.G.; Surette, R.A.; Brown, R.M.

1993-01-01

Current methods for sampling and measuring tritium are described. Although the basic techniques have not changed significantly over the last 10 y, there have been several notable improvements in tritium measurement instrumentation. The design and quality of commercial ion-chamber-based and gas-flow-proportional-counter-based tritium monitors for tritium-in-air have improved, an indirect result of fusion-related research in the 1980s. For tritium-in-water analysis, commercial low-level liquid scintillation spectrometers capable of detecting tritium-in-water concentrations as low as 0.65 Bq L-1 for counting times of 500 min are available. The most sensitive method for tritium-in-water analysis is still 3He mass spectrometry. Concentrations as low as 0.35 mBq L-1 can be detected with current equipment. Passive tritium-oxide-in-air samplers are now being used for workplace monitoring and even in some environmental sampling applications. The reliability, convenience, and low cost of passive tritium-oxide-in-air samplers make them attractive options for many monitoring applications. Airflow proportional counters currently under development look promising for measuring tritium-in-air in the presence of high gamma and/or noble gas backgrounds. However, these detectors are currently limited by their poor performance in humidities over 30%. 133 refs

Robust weak measurements on finite samples

International Nuclear Information System (INIS)

Tollaksen, Jeff

2007-01-01

A new weak measurement procedure is introduced for finite samples which yields accurate weak values that are outside the range of eigenvalues and which do not require an exponentially rare ensemble. This procedure provides a unique advantage in the amplification of small nonrandom signals by minimizing uncertainties in determining the weak value and by minimizing sample size. This procedure can also extend the strength of the coupling between the system and measuring device to a new regime

A Universal Logging System for LHCb Online

International Nuclear Information System (INIS)

Nikolaidis, Fotis; Brarda, Loic; Garnier, Jean-Christophe; Neufeld, Niko

2011-01-01

A log is recording of system's activity, aimed to help system administrator to traceback an attack, find the causes of a malfunction and generally with troubleshooting. The fact that logs are the only information an administrator may have for an incident, makes logging system a crucial part of an IT infrastructure. In large scale infrastructures, such as LHCb Online, where quite a few GB of logs are produced daily, it is impossible for a human to review all of these logs. Moreover, a great percentage of them as just n oise . That makes clear that a more automated and sophisticated approach is needed. In this paper, we present a low-cost centralized logging system which allow us to do in-depth analysis of every log.

Drilling and associated drillhole measurements of the pilot hole ONK-PH9

International Nuclear Information System (INIS)

Karttunen, P.; Pekkanen, J.; Poellaenen, J.; Tarvainen, A.-M.; Toropainen, V.; Lamminmaeki, T.; Kosunen, P.

2010-01-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH9 was drilled from chainage 3263 to chainage 3413.27 in November 2008. The length of the hole is 150.3 metres. The aim during the drilling work was to orient core samples as much as possible. The deviation of the drillhole was measured during and after the drilling phase. Electric conductivity was measured from the collected returning water samples. Hydraulic conductivity of the fractures or fractured zones was measured by Posiva Flow Log equipment. The measurements were done in two phases. During flow measurements also electric conductivity, grounding resistance and temperature were measured. In flow logging test sections of 0.5 m and increments of 0.1 m were used. The water loss measurements were performed after drilling was completed by the drilling company. Logging of the core samples included the following parameters: lithology, foliation, fracturing, fracture frequency, RQD, fractured zones, core loss, and weathering. The rock mechanical logging was based on Q-classification. The rock strength and deformation were determined with Rock Tester equipment. Geophysical logging and optical imaging of the pilot hole included the fieldwork of all surveys, the integration of the data as well as interpretation of the acoustic and drillhole radar data. One of the objectives of the geochemical study

Model wells for nuclear well logging

International Nuclear Information System (INIS)

Tittle, C.W.

1989-01-01

Considerations needed in the design and construction of model wells for nuclear log calibration are covered, with special attention to neutron porosity logging and total γ-ray logging. Pulsed neutron decay-time and spectral γ-ray logging are discussed briefly. The American Petroleum Institute calibration facility for nuclear logs is a good starting point for similar or expanded facilities. A few of its shortcomings are mentioned; they are minor. The problem of fluid saturation is emphasized. Attention is given to models made of consolidated rock and those containing unconsolidated material such as Ottawa sand. Needed precautions are listed. A similarity method is presented for estimating the porosity index of formations that are not fully saturated. (author)

LBA-ECO TG-07 Trace Gas Fluxes, Undisturbed and Logged Sites, Para, Brazil: 2000-2002

Science.gov (United States)

M.M. Keller; R.K. Varner; J.D. Dias; H.S. Silva; P.M. Crill; Jr. de Oliveira; G.P. Asner

2009-01-01

Trace gas fluxes of carbon dioxide, methane, nitrous oxide, and nitric oxide were measured manually at undisturbed and logged forest sites in the Tapajos National Forest, near Santarem, Para, Brazil. Manual measurements were made approximately weekly at both the undisturbed and logged sites. Fluxes from clay and sand soils were completed at the undisturbed sites....

Assessment of PDMS-water partition coefficients: implications for passive environmental sampling of hydrophobic organic compounds

Science.gov (United States)

DiFilippo, Erica L.; Eganhouse, Robert P.

2010-01-01

Solid-phase microextraction (SPME) has shown potential as an in situ passive-sampling technique in aquatic environments. The reliability of this method depends upon accurate determination of the partition coefficient between the fiber coating and water (Kf). For some hydrophobic organic compounds (HOCs), Kf values spanning 4 orders of magnitude have been reported for polydimethylsiloxane (PDMS) and water. However, 24% of the published data examined in this review did not pass the criterion for negligible depletion, resulting in questionable Kf values. The range in reported Kf is reduced to just over 2 orders of magnitude for some polychlorinated biphenyls (PCBs) when these questionable values are removed. Other factors that could account for the range in reported Kf, such as fiber-coating thickness and fiber manufacturer, were evaluated and found to be insignificant. In addition to accurate measurement of Kf, an understanding of the impact of environmental variables, such as temperature and ionic strength, on partitioning is essential for application of laboratory-measured Kf values to field samples. To date, few studies have measured Kf for HOCs at conditions other than at 20 degrees or 25 degrees C in distilled water. The available data indicate measurable variations in Kf at different temperatures and different ionic strengths. Therefore, if the appropriate environmental variables are not taken into account, significant error will be introduced into calculated aqueous concentrations using this passive sampling technique. A multiparameter linear solvation energy relationship (LSER) was developed to estimate log Kf in distilled water at 25 degrees C based on published physicochemical parameters. This method provided a good correlation (R2 = 0.94) between measured and predicted log Kf values for several compound classes. Thus, an LSER approach may offer a reliable means of predicting log Kf for HOCs whose experimental log Kf values are presently unavailable. Future

Artificial intelligence approach to interwell log correlation

Energy Technology Data Exchange (ETDEWEB)

Lim, Jong-Se [Korea Maritime University, Pusan(Korea); Kang, Joo Myung [Seoul National University, Seoul(Korea); Kim, Jung Whan [Korea National Oil Corp., Anyang(Korea)

2000-04-30

This paper describes a new approach to automated interwell log correlation using artificial intelligence and principal component analysis. The approach to correlate wire line logging data is on the basis of a large set of subjective rules that are intended to represent human logical processes. The data processed are mainly the qualitative information such as the characteristics of the shapes extracted along log traces. The apparent geologic zones are identified by pattern recognition for the specific characteristics of log trace collected as a set of objects by object oriented programming. The correlation of zones between wells is made by rule-based inference program. The reliable correlation can be established from the first principal component logs derived from both the important information around well bore and the largest common part of variances of all available well log data. Correlation with field log data shows that this approach can make interwell log correlation more reliable and accurate. (author). 6 refs., 7 figs.

Comparison of sampling methods to measure HIV RNA viral load in female genital tract secretions.

Science.gov (United States)

Jaumdally, Shameem Z; Jones, Heidi E; Hoover, Donald R; Gamieldien, Hoyam; Kriek, Jean-Mari; Langwenya, Nontokozo; Myer, Landon; Passmore, Jo-Ann S; Todd, Catherine S

2017-03-01

How does menstrual cup (MC) compare to other genital sampling methods for HIV RNA recovery? We compared HIV RNA levels between MC, endocervical swab (ECS), and ECS-enriched cervicovaginal lavage (eCVL) specimens in 51 HIV-positive, antiretroviral therapy-naive women at enrollment, 3 and 6 months, with order rotated by visit. Paired comparisons were analyzed with McNemar's exact tests, signed-rank tests, and an extension of Somer's D for pooled analyses across visits. MC specimens had the highest proportion of quantifiable HIV VL at enrollment and month 3, but more MC specimens (n=12.8%) were insufficient for testing, compared with ECS (2%, P=0.006) and eCVL (0%, P<0.001). Among sufficient specimens, median VL was significantly higher for MC (2.62 log 10 copies/mL) compared to ECS (1.30 log 10 copies/mL, P<0.001) and eCVL (1.60 log 10 copies/mL, P<0.001) across visits. MC may be more sensitive than eCVL and CVS, provided insufficient specimens are reduced. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Device for radioactivity measurement of liquid samples

International Nuclear Information System (INIS)

Lamaziere, J.

1983-01-01

The device for low activity gamma measurements comprises an automatic changer for sample transfer from a conveyor to a measuring chamber. The conveyor includes a horizontal table were are regularly distributed sample holders. A lift allows a vertical motion of a plate for the exposition in front of a detector [fr

Measurements of plutonium in environmental samples

International Nuclear Information System (INIS)

D'Alberti, F.; Risposi, L.

1996-01-01

Within the activities connected with the start up of the PETRA Laboratory (Processo per l'Estrazione di Terre Rare ed Attinidi, i.e. process for extraction of rare earths and actinides), the Radiation Protection Unit of the J.R.C.-Ispra has carried out a well planned set of experimental measurements aimed at evaluating the zero point of the isotopes of plutonium in environmental samples by alfa spectrometry. After the International Moratorium in 1963, no release of plutonium has occurred in the environment apart from the burn up of SNAP 9A satellite in April 1964. Since then the plutonium concentration in air and in fallout samples has been continuously decreasing requiring, therefore, optimization of both instrumentation and experimental measurement procedures in order to obtain better sensibilities. In this work, the experimental methodology followed at the J.R.C.-Ispra for measurements of plutonium concentration in air, deposition and soil is described and the plutonium behaviour in these samples is reported and discussed starting from 1961

Measurements of plutonium in environmental samples

Energy Technology Data Exchange (ETDEWEB)

D' Alberti, F; Risposi, L [Instituto di Fisica Applicata, University of Milan, Milan (Italy)

1996-01-01

Within the activities connected with the start up of the PETRA Laboratory (Processo per l'Estrazione di Terre Rare ed Attinidi, i.e. process for extraction of rare earths and actinides), the Radiation Protection Unit of the J.R.C.-Ispra has carried out a well planned set of experimental measurements aimed at evaluating the zero point of the isotopes of plutonium in environmental samples by alfa spectrometry. After the International Moratorium in 1963, no release of plutonium has occurred in the environment apart from the burn up of SNAP 9A satellite in April 1964. Since then the plutonium concentration in air and in fallout samples has been continuously decreasing requiring, therefore, optimization of both instrumentation and experimental measurement procedures in order to obtain better sensibilities. In this work, the experimental methodology followed at the J.R.C.-Ispra for measurements of plutonium concentration in air, deposition and soil is described and the plutonium behaviour in these samples is reported and discussed starting from 1961.

Processing of gamma-ray spectrometric logs

International Nuclear Information System (INIS)

Umiastowski, K.; Dumesnil, P.

1984-10-01

CEA (Commissariat a l'Energie Atomique) has developped a gamma-ray spectrometric tool, containing an analog-to-digital converter. This new tool permits to perform very precise uranium logs (natural gamma-ray spectrometry), neutron activation logs and litho-density logs (gamma-gamma spectrometric logs). Specific processing methods were developped to treate the particular problems of down-hole gamma-ray spectrometry. Extraction of the characteristic gamma-ray peak, even if they are superposed on the background radiation of very high intensity, is possible. This processing methode enables also to obtain geological informations contained in the continuous background of the spectrum. Computer programs are written in high level language for SIRIUS (VICTOR) and APOLLO computers. Exemples of uranium and neutron activation logs treatment are presented [fr

Assessment of the Log-Euclidean Metric Performance in Diffusion Tensor Image Segmentation

Directory of Open Access Journals (Sweden)

Mostafa Charmi

2010-06-01

Full Text Available Introduction: Appropriate definition of the distance measure between diffusion tensors has a deep impact on Diffusion Tensor Image (DTI segmentation results. The geodesic metric is the best distance measure since it yields high-quality segmentation results. However, the important problem with the geodesic metric is a high computational cost of the algorithms based on it. The main goal of this paper is to assess the possible substitution of the geodesic metric with the Log-Euclidean one to reduce the computational cost of a statistical surface evolution algorithm. Materials and Methods: We incorporated the Log-Euclidean metric in the statistical surface evolution algorithm framework. To achieve this goal, the statistics and gradients of diffusion tensor images were defined using the Log-Euclidean metric. Numerical implementation of the segmentation algorithm was performed in the MATLAB software using the finite difference techniques. Results: In the statistical surface evolution framework, the Log-Euclidean metric was able to discriminate the torus and helix patterns in synthesis datasets and rat spinal cords in biological phantom datasets from the background better than the Euclidean and J-divergence metrics. In addition, similar results were obtained with the geodesic metric. However, the main advantage of the Log-Euclidean metric over the geodesic metric was the dramatic reduction of computational cost of the segmentation algorithm, at least by 70 times. Discussion and Conclusion: The qualitative and quantitative results have shown that the Log-Euclidean metric is a good substitute for the geodesic metric when using a statistical surface evolution algorithm in DTIs segmentation.

Quantifying diagnostic performance: The log odds method as a practical option

International Nuclear Information System (INIS)

Haslam, Maxine; Manning, David

2006-01-01

Purpose: To investigate the most practical option available when statistically analysing small sample size studies. Method: The log odds ratio was applied to a study which took a retrospective approach and involved 50 patients who had undergone a ventilation and perfusion scan in the period between 01 January 2002 and 31 December 2002. Radiology reports and the patients' medical records were obtained, so that the clinical indications for the examination and the patients' medical history could be transferred onto the report form. Four radiographers who are routinely rotated into the Nuclear Medicine Department independently reported the same 50 ventilations and perfusion scans under identical conditions to the reporting radiologist. Results: Taking the radiologist reports as the gold standard the radiographers had an accuracy rate of 78%. The radiographers recorded an average sensitivity value of 94% and specificity value of 63%, with an A z reading of 0.71. Conclusion: As the sample size was too small for a receiver operating characteristic (ROC) curve to be drawn, the log odds ratio provided a value, which represents an area under the receiver operating characteristic (ROC) curve, which in turn ensured the results were statistically reliable. The log odds ratio enables researchers to carry out small-scale research without harbouring the data collected by unreliable analysis

Optimised method to estimate octanol water distribution coefficient (logD) in a high throughput format.

Science.gov (United States)

Low, Ying Wei Ivan; Blasco, Francesca; Vachaspati, Prakash

2016-09-20

Lipophilicity is one of the molecular properties assessed in early drug discovery. Direct measurement of the octanol-water distribution coefficient (logD) requires an analytical method with a large dynamic range or multistep dilutions, as the analyte's concentrations span across several orders of magnitude. In addition, water/buffer and octanol phases which have very different polarity could lead to matrix effects and affect the LC-MS response, leading to erroneous logD values. Most compound libraries use DMSO stocks as it greatly reduces the sample requirement but the presence of DMSO has been shown to underestimate the lipophilicity of the analyte. The present work describes the development of an optimised shake flask logD method using deepwell 96 well plate that addresses the issues related to matrix effects, DMSO concentration and incubation conditions and is also amenable to high throughput. Our results indicate that the equilibrium can be achieved within 30min by flipping the plate on its side while even 0.5% of DMSO is not tolerated in the assay. This study uses the matched matrix concept to minimise the errors in analysing the two phases namely buffer and octanol in LC-MS. Copyright © 2016 Elsevier B.V. All rights reserved.

Nondestructive evaluation for sorting red maple logs

Science.gov (United States)

Xiping Wang; Robert J. Ross; David W. Green; Karl Englund; Michael Wolcott

2000-01-01

Existing log grading procedures in the United States make only visual assessments of log quality. These procedures do not incorporate estimates of the modulus of elasticity (MOE) of logs. It is questionable whether the visual grading procedures currently used for logs adequately assess the potential quality of structural products manufactured from them, especially...

SNG-logs at the Bagsvaerd Lake

International Nuclear Information System (INIS)

Korsbech, U.

1992-11-01

Spectral Natural Gamma-logs (SNG) were taken in old boreholes around Bagsvaerd Lake (Zealand). The purpose of this investigation was to clarify the geologic/lithologic conditions in this region and the potential risks of waste penetration into ground water. Relationship curves for thorium, uranium and potassium concentrations are given. Some special logs which can be useful for evaluating concentration variations or transition forms among various lithological layers are collected. Appendices contain technical information on the boreholes and discussion of differences between results of SNG-logging and the conventional gamma-logging. (EG)

Analysis of the magnetic susceptibility well log in drill hole UE25a-5, Yucca Mountain, Nevada Test Site

International Nuclear Information System (INIS)

Hagstrum, J.T.; Daniels, J.J.; Scott, J.H.

1980-01-01

Magnetic susceptibility measurements have been shown to be dependent upon the magnetite content of rocks with variations in rock susceptibility arising from changes in the shape, size, composition, and quantity of the contained magnetite grains. The present study was undertaken to determine the factor(s) responsible for the variation in magnetic susceptibility measurements from borehole UE25a-5 on the Nevada Test Site (NTS). The well logs and sample analyses presented in this paper form part of a larger geophysical well-logging project studying the physical properties of welded tuffs at NTS. The ash-flow sheets at NTS appear to be the products of single compositionally zoned magmas that tend, within a cooling unit, to erupt hotter, more mafic, and more crystal-rich with time. These factors, however, have little effect on the degree to which the tuffs become welded. Furthermore, zones of crystallization and alteration are superimposed upon the welded units. X-ray data show poor correspondence between the relative abundance of magnetite in a sample and the borehole magnetic susceptibility measurement associated with it. Curie balance experiments demonstrate no change in the magnetic mineralogy that could account for the susceptibility variation. Thin-section observations corroborate the x-ray data, but indicate a proportional relationship between the borehole susceptibility measurements and the grain-size distribution of magnetite. The association of magnetic susceptibility anomalies with the crystal-rich zones of the welded tuffs will aid in the identification and correlation of the eruptive sequences at NTS

Application of accelerator sources for pulsed neutron logging of oil and gas wells

International Nuclear Information System (INIS)

Randall, R.R.

1985-01-01

Dresser Atlas introduced the first commercial pulsed neutron oil well log in the early 1960s. This log had the capability of differentiating oil from salt water in a completed well. In the late 1970s the first continuous carbon/oxygen (C/O) log capable of differentiating oil from fresh water was introduced. The sources used in these commercial logs are radial geometry deuterium-tritium reaction devices with Cockcroft-Walton voltage multipliers providing the accelerator voltage. The commercial logging tools using these accelerators are comprised of scintillators detectors, power supplies, line drivers and receivers, and various timing and communication electronics. They are used to measure either the time decay or energy spectra of neutron-induced gamma events. The time decay information is useful in determining the neutron capture cross section, and the energy spectra is used to characterize inelastic neutron events. (orig.)

Application of accelerator sources for pulsed neutron logging of oil and gas wells

Science.gov (United States)

Randall, R. R.

1985-05-01

Dresser Atlas introduced the first commercial pulsed neutron oil well log in the early 1960s. This log had the capability of differentiating oil from salt water in a completed well. In the late 1970s the first continuous carbon/oxygen (C/O) log capable of differentiating oil from fresh water was introduced. The sources used in these commercial logs are radial geometry deuterium-tritium reaction devices with Cockcroft-Walton voltage multipliers providing the accelerator voltage. The commercial logging tools using these accelerators are comprised of scintillators detectors, power supplies, line drivers and receivers, and various timing and communications electronics. They are used to measure either the time decay or energy spectra of neutron-induced gamma events. The time decay information is useful in determining the neutron capture cross section, and the energy spectra is used to characterize inelastic neutron events.

Geophysical logging for groundwater investigations in Southern Thailand

Directory of Open Access Journals (Sweden)

Phongpiyah Klinmanee

2012-09-01

Full Text Available In Thailand the Department of Groundwater Resources is drilling to find vital aquifers. Sometimes groundwater formations cannot be identified clearly during drilling; therefore, geophysical logging was applied after drilling and before casing.The tool used here is measuring nine parameters in one run, natural gamma ray, spontaneous potential, single point resistance, normal resistivity (AM 8’’, 16’’, 32’’, and 64’’, mud temperature and resistivity. Cutting was used to support the geophysical interpretations. In many cases the groundwater bearing zones could be clearly identified. The combination of andthe possibility choosing from nine parameters measured provided the necessary data base to identify groundwater bearingzones in different environments. It has been demonstrated that in different wells different tools are favorable than others.Based on the conclusions of this study geophysical logging in groundwater exploration is recommended as a normalstandard technique that should be applied in every new well drilled.

LHCb Online Log Analysis and Maintenance System

CERN Document Server

Garnier, J-C

2011-01-01

History has shown, many times computer logs are the only information an administrator may have for an incident, which could be caused either by a malfunction or an attack. Due to the huge amount of logs that are produced from large-scale IT infrastructures, such as LHCb Online, critical information may be overlooked or simply be drowned in a sea of other messages. This clearly demonstrates the need for an automatic system for long-term maintenance and real time analysis of the logs. We have constructed a low cost, fault tolerant centralized logging system which is able to do in-depth analysis and cross-correlation of every log. This system is capable of handling O(10000) different log sources and numerous formats, while trying to keep the overhead as low as possible. It provides log gathering and management, Offline analysis and online analysis. We call Offline analysis the procedure of analyzing old logs for critical information, while Online analysis refer to the procedure of early alerting and reacting. ...

Drilling and the associated drillhole measurements of the pilot hole ONK-PH8

International Nuclear Information System (INIS)

Karttunen, P.; Poellaenen, J.; Rautio, T.; Tarvainen, A.-M.; Lamminmaeki, T.; Kemppainen, K.; Kosunen, P.; Lampinen, H.

2009-02-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH8 was drilled from chainage 3116 to chainage 3266.29 in June- July 2008. The length of the hole is 150.29 metres. The aim during the drilling work was to orient core samples as much as possible. The deviation of the drillhole was measured during and after the drilling phase. Electric conductivity was measured from the collected returning water samples. Water conductivity of the fractures or fractured zones was measured by Posiva Flow Log equipment. The measurements were done in two phases. During flow measurements also grounding resistance, electric conductivity and temperature were measured. In flow logging test sections of 0.5 m and increments of 0.1 m were used. The water loss measurements failed. Logging of the core samples included the following parameters: lithology, foliation, fracturing, fracture frequency, RQD, fractured zones, core loss, and weathering. The rock mechanical logging was based on Q-classification. The test to determine rock strength and deformation were made with Rock Tester-equipment. Geophysical logging and optical imaging of the pilot hole included the fieldwork of all surveys, the integration of the data as well as interpretation of the acoustic and drillhole radar data. One of the objectives of the geochemical study was to get information of the composition of ONKALO

ECLogger: Cross-Project Catch-Block Logging Prediction Using Ensemble of Classifiers

Directory of Open Access Journals (Sweden)

Sangeeta Lal

2017-01-01

Full Text Available Background: Software developers insert log statements in the source code to record program execution information. However, optimizing the number of log statements in the source code is challenging. Machine learning based within-project logging prediction tools, proposed in previous studies, may not be suitable for new or small software projects. For such software projects, we can use cross-project logging prediction. Aim: The aim of the study presented here is to investigate cross-project logging prediction methods and techniques. Method: The proposed method is ECLogger, which is a novel, ensemble-based, cross-project, catch-block logging prediction model. In the research We use 9 base classifiers were used and combined using ensemble techniques. The performance of ECLogger was evaluated on on three open-source Java projects: Tomcat, CloudStack and Hadoop. Results: ECLogger Bagging, ECLogger AverageVote, and ECLogger MajorityVote show a considerable improvement in the average Logged F-measure (LF on 3, 5, and 4 source -> target project pairs, respectively, compared to the baseline classifiers. ECLogger AverageVote performs best and shows improvements of 3.12% (average LF and 6.08% (average ACC – Accuracy. Conclusion: The classifier based on ensemble techniques, such as bagging, average vote, and majority vote outperforms the baseline classifier. Overall, the ECLogger AverageVote model performs best. The results show that the CloudStack project is more generalizable than the other projects.

Displacement length and velocity of tagged logs in the tagliamento river

Directory of Open Access Journals (Sweden)

Diego Ravazzolo

2013-09-01

Full Text Available Large wood enhance the dynamics of geomorphic processes in river systems, increases the morphological complexity of the channel bed, and provides habitats for fish and invertebrates. On the other side, if transported during high-magnitude events, large wood pieces can increase flood risks in sensitive places such as bridges and narrow cross sections prone to outbank flows. However, the dynamics and mobility of logs in rivers is poorly understood, especially in wide gravel-bed rivers. Recent studies have employed fixed video cameras to assess logs velocity, but little evidence is still available about travel length during flood events of different magnitude. This study was conducted in a valley reach of the Tagliamento river, located in the North East of Italy. The Tagliamento river is approximately 800 m wide in the study area, and is characterized by relatively high natural conditions and complex fluvial dynamics. Log mobility have been studied from June 2010 to October 2011, a period characterized by a relatively high magnitude flood in November 2010. Log mobility and displacement during floods have been measured by implanting active radio transmitters (RFID in 113 logs and GPS track devices in 42 logs. The first devices allow to recover the log after flood events by using a portable antenna, and to derive the displacement length over the monitoring period, whereas the second devices allows to calculate instantaneous (1 sec and average log velocity of moving logs. Recovery rate of logs equipped with RFID and GPS was about 50% and 60%, respectively. A preliminary analysis of the data collected indicates that there is a positive relationship between displacement length and the peak of flood events, as well as a positive relationship between log velocity and the flood magnitude. Also, a critical flow rate over which logs stranded on active bars can be transported has been identified. The ability to predict wood mobility in gravel-bed rivers could

Modeling Precipitation Extremes using Log-Histospline

Science.gov (United States)

Huang, W. K.; Nychka, D. W.; Zhang, H.

2017-12-01

One of the commonly used approaches to modeling univariate extremes is the peaks-overthreshold (POT) method. The POT method models exceedances over a (sufficiently high/low) threshold as a generalized Pareto distribution (GPD). To apply this method, a threshold has to be chosen and the estimates might be sensitive to the chosen threshold. Here we propose an alternative, the "Log-Histospline", to explore modeling the tail behavior and the remainder of the density in one step using the full range of the data. Log-Histospline applies a smoothing spline model on a finely binned histogram of the log transformed data to estimate its log density. By construction, we are able to preserve the polynomial upper tail behavior, a feature commonly observed in geophysical observations. The Log-Histospline can be extended to the spatial setting by treating the marginal (log) density at each location as spatially indexed functional data, and perform a dimension reduction and spatial smoothing. We illustrate the proposed method by analyzing precipitation data from regional climate model output (North American Regional Climate Change and Assessment Program (NARCCAP)).

Log-Log Convexity of Type-Token Growth in Zipf's Systems

Science.gov (United States)

Font-Clos, Francesc; Corral, Álvaro

2015-06-01

It is traditionally assumed that Zipf's law implies the power-law growth of the number of different elements with the total number of elements in a system—the so-called Heaps' law. We show that a careful definition of Zipf's law leads to the violation of Heaps' law in random systems, with growth curves that have a convex shape in log-log scale. These curves fulfill universal data collapse that only depends on the value of Zipf's exponent. We observe that real books behave very much in the same way as random systems, despite the presence of burstiness in word occurrence. We advance an explanation for this unexpected correspondence.

Case-Logging Practices in Otolaryngology Residency Training: National Survey of Residents and Program Directors.

Science.gov (United States)

Dermody, Sarah M; Gao, William; McGinn, Johnathan D; Malekzadeh, Sonya

2017-06-01

Objective (1) Evaluate the consistency and manner in which otolaryngology residents log surgical cases. (2) Assess the extent of instruction and guidance provided by program directors on case-logging practices. Study Design Cross-sectional national survey. Setting Accreditation Council for Graduate Medical Education otolaryngology residency programs in the United States. Subjects and Methods US otolaryngology residents, postgraduate year 2 through graduating chiefs as of July 2016, were recruited to respond to an anonymous questionnaire designed to characterize surgical case-logging practices. Program directors of US otolaryngology residency programs were recruited to respond to an anonymous questionnaire to elucidate how residents are instructed to log cases. Results A total of 272 residents and 53 program directors completed the survey, yielding response rates of 40.6% and 49.5%, respectively. Perceived accuracy of case logs is low among residents and program directors. Nearly 40% of residents purposely choose not to log certain cases, and 65.1% of residents underreport cases performed. More than 80% of program directors advise residents to log procedures performed outside the operating room, yet only 16% of residents consistently log such cases. Conclusion Variability in surgical case-logging behaviors and differences in provided instruction highlight the need for methods to improve consistency of logging practices. It is imperative to standardize practices across otolaryngology residency programs for case logs to serve as an accurate measure of surgical competency. This study provides a foundation for reform efforts within residency programs and for the Resident Case Log System.

Sampling and measurement of long-lived radionuclides in environmental samples

International Nuclear Information System (INIS)

Brauer, F.P.; Goles, R.W.; Kaye, J.H.; Rieck, H.G. Jr.

1977-01-01

The volatile and semivolatile long-lived man-made radionuclides 3 H, 14 C, 79 Se, 85 Kr, 99 Tc, 129 I, 135 Cs, and 137 Cs are of concern in operation of nuclear facilities because they are difficult and expensive to contain and once emitted to the environment they become permanent ecological constituents with both local and global distributions. Species-selective sampling and analytical methods (radiochemical, neutron activation, and mass spectrometric) have been developed for many of these nuclides with sensitivities well below those required for radiation protection. These sampling and analytical methods have been applied to the measurement of current environmental levels of some of the more ecologically important radionuclides. The detection and tracing of long-lived radionuclides is being conducted in order to establish base-line values and to study environmental behavior. This paper describes detection and measurement techniques and summarizes current measurement results

Geophysical borehole logging

International Nuclear Information System (INIS)

McCann, D.; Barton, K.J.; Hearn, K.

1981-08-01

Most of the available literature on geophysical borehole logging refers to studies carried out in sedimentary rocks. It is only in recent years that any great interest has been shown in geophysical logging in boreholes in metamorphic and igneous rocks following the development of research programmes associated with geothermal energy and nuclear waste disposal. This report is concerned with the programme of geophysical logging carried out on the three deep boreholes at Altnabreac, Caithness, to examine the effectiveness of these methods in crystalline rock. Of particular importance is the assessment of the performance of the various geophysical sondes run in the boreholes in relation to the rock mass properties. The geophysical data can be used to provide additional in-situ information on the geological, hydrogeological and engineering properties of the rock mass. Fracturing and weathering in the rock mass have a considerable effect on both the design parameters for an engineering structure and the flow of water through the rock mass; hence, the relation between the geophysical properties and the degree of fracturing and weathering is examined in some detail. (author)

Reconciling the Log-Linear and Non-Log-Linear Nature of the TSH-Free T4 Relationship: Intra-Individual Analysis of a Large Population.

Science.gov (United States)

Rothacker, Karen M; Brown, Suzanne J; Hadlow, Narelle C; Wardrop, Robert; Walsh, John P

2016-03-01

The TSH-T4 relationship was thought to be inverse log-linear, but recent cross-sectional studies report a complex, nonlinear relationship; large, intra-individual studies are lacking. Our objective was to analyze the TSH-free T4 relationship within individuals. We analyzed data from 13 379 patients, each with six or more TSH/free T4 measurements and at least a 5-fold difference between individual median TSH and minimum or maximum TSH. Linear and nonlinear regression models of log TSH on free T4 were fitted to data from individuals and goodness of fit compared by likelihood ratio testing. Comparing all models, the linear model achieved best fit in 31% of individuals, followed by quartic (27%), cubic (15%), null (12%), and quadratic (11%) models. After eliminating least favored models (with individuals reassigned to best fitting, available models), the linear model fit best in 42% of participants, quartic in 43%, and null model in 15%. As the number of observations per individual increased, so did the proportion of individuals in whom the linear model achieved best fit, to 66% in those with more than 20 observations. When linear models were applied to all individuals and averaged according to individual median free T4 values, variations in slope and intercept indicated a nonlinear log TSH-free T4 relationship across the population. The log TSH-free T4 relationship appears linear in some individuals and nonlinear in others, but is predominantly linear in those with the largest number of observations. A log-linear relationship within individuals can be reconciled with a non-log-linear relationship in a population.

Linking log quality with product performance

Science.gov (United States)

D. W. Green; Robert Ross

1997-01-01

In the United States, log grading procedures use visual assessment of defects, in relation to the log scaling diameter, to estimate the yield of lumber that maybe expected from the log. This procedure was satisfactory when structural grades were based only on defect size and location. In recent years, however, structural products have increasingly been graded using a...

Logística del transporte

OpenAIRE

Robusté Antón, Francesc

2005-01-01

La logística se ha conformado como un proceso estratégico para organizar las actividades de producción y de distribución de las empresas. El concepto de sistema logístico ha incluido un amplio espectro de operaciones que condicionan la eficiencia y la competitividad empresarial en el actual contexto de globalización de la economía. En este sentido, este libro afronta y analiza los distintos aspectos que inciden en los procesos de planificación y gestión de los procesos logísticos relacionados...

Engineering aspects of radiometric logging

International Nuclear Information System (INIS)

Huppert, P.

1982-01-01

Engineering problems encountered in the development of nuclear borehole logging techniques are discussed. Spectrometric techniques require electronic stability of the equipment. In addition the electronics must be capable of handling high count rates of randomly distributed pulses of fast rise time from the detector and the systems must be designed so that precise calibration is possible under field operating conditions. Components of a logging system are discussed in detail. They include the logging probe (electronics, detector, high voltage supply, preamplifier), electronic instrumentation for data collection and processing and auxiliary equipment

Data logging system upgrade for Indus accelerator

International Nuclear Information System (INIS)

Mishra, R.; Merh, B.N.; Agrawal, R.K.; Fatnani, P.; Navathe, C.P.; Pal, S.

2012-01-01

An accelerator has various subsystems like Magnet Power Supply, Beam Diagnostics and Vacuum etc. which are required to work in a stable manner to ensure required machine performance. Logging of system parameters at a faster rate plays a crucial role in analysing and understanding machine behaviour. Logging all the machine parameters consistently at the rate of typically more than 1 Hz has been the aim of a recent data logging system upgrade. Nearly ten thousand parameters are being logged at varying intervals of one second to one minute in Indus accelerator complex. The present logging scheme is augmented to log all these parameters at a rate equal to or more than 1 Hz. The database schema is designed according to the data type of the parameter. The data is distributed into historical table and intermediate table which comprises of recent data. Machine control applications read the parameter values from the control system and store them into the text files of finite time duration for each sub-system. The logging application of each sub-system passes these text files to database for bulk insertion. The detail design of database, logging scheme and its architecture is presented in the paper. (author)

Rill erosion in burned and salvage logged western montane forests: Effects of logging equipment type, traffic level, and slash treatment

Science.gov (United States)

Wagenbrenner, J. W.; Robichaud, P. R.; Brown, R. E.

2016-10-01

Following wildfires, forest managers often consider salvage logging burned trees to recover monetary value of timber, reduce fuel loads, or to meet other objectives. Relatively little is known about the cumulative hydrologic effects of wildfire and subsequent timber harvest using logging equipment. We used controlled rill experiments in logged and unlogged (control) forests burned at high severity in northern Montana, eastern Washington, and southern British Columbia to quantify rill overland flow and sediment production rates (fluxes) after ground-based salvage logging. We tested different types of logging equipment-feller-bunchers, tracked and wheeled skidders, and wheeled forwarders-as well as traffic levels and the addition of slash to skid trails as a best management practice. Rill experiments were done at each location in the first year after the fire and repeated in subsequent years. Logging was completed in the first or second post-fire year. We found that ground-based logging using heavy equipment compacted soil, reduced soil water repellency, and reduced vegetation cover. Vegetation recovery rates were slower in most logged areas than the controls. Runoff rates were higher in the skidder and forwarder plots than their respective controls in the Montana and Washington sites in the year that logging occurred, and the difference in runoff between the skidder and control plots at the British Columbia site was nearly significant (p = 0.089). Most of the significant increases in runoff in the logged plots persisted for subsequent years. The type of skidder, the addition of slash, and the amount of forwarder traffic did not significantly affect the runoff rates. Across the three sites, rill sediment fluxes were 5-1900% greater in logged plots than the controls in the year of logging, and the increases were significant for all logging treatments except the low use forwarder trails. There was no difference in the first-year sediment fluxes between the feller

Short-term responses to watershed logging on biomass mercury and methylmercury accumulation by periphyton in boreal lakes

Energy Technology Data Exchange (ETDEWEB)

Desrosiers, M.; Planas, D. [Quebec Univ., Montreal, PQ (Canada). Dept. de sciences biologiques; Mucci, A. [McGill Univ., Montreal, PQ (Canada). Dept. of Earth and Planetary Sciences

2006-08-15

Increased timber harvesting in the boreal regions of Quebec may have a significant impact on aquatic ecosystems. Watershed disturbances such as logging increase chemical loading to lakes. Soil in the Canadian Shield readily adsorbs and accumulates mercury (Hg) from atmospheric deposition. Forest watersheds serve as large reservoirs of Hg that shed their metal load when soil and land hydrology are disrupted. This paper presented the results of a study evaluating the impact of logging on periphyton algal biomass and dry mass. The study also evaluated the impact of total mercury (THG) and methylmercury (MeHg) accumulation in the littoral zone of the boreal lakes. A before-after control-impact (BACI) sample design was applied that required data from control and target sites sampled both before and after the disturbances. The study was carried out on 18 boreal lakes located in the Grenville geological province. Eight lakes had their watersheds logged over 15 to 79 per cent of their area. A further 10 lakes were used as control sites to document interannual variations. The project used water quality and physiographic data acquired by research groups within the Sustainable Forest Management Network. Fourteen study lakes were sampled once a year during 2 consecutive ice-free seasons before and after logging, and another 4 lakes were sampled 2 years after logging. Significant decreases in algal biomass and increases in MeHg concentrations in periphyton mats in a majority of the harvested watershed lakes were detected. The increases may have a significant impact on organisms of higher trophic levels as they are at the base of the food web. Results suggested that the observed decrease in periphyton biomass combined with the increase in MeHg accumulation may magnify the impact of logging activities on fish and other aquatic predators. Two years after logging, it was observed that MeHg concentrations were still increasing. It was concluded that further research is needed

Impact of elliptical shaped red oak logs on lumber grade and volume recovery

Science.gov (United States)

Patrick M. Rappold; Brian H. Bond; Janice K. Wiedenbeck; Roncs Ese-Etame

2007-01-01

This research examined the grade and volume of lumber recovered from red oak logs with elliptical shaped cross sections. The volume and grade of lumber recovered from red oak logs with low (e ≤ 0.3) and high (e ≥ 0.4) degrees of ellipticity was measured at four hardwood sawmills. There was no significant difference (...

TH-AB-201-12: Using Machine Log-Files for Treatment Planning and Delivery QA

Energy Technology Data Exchange (ETDEWEB)

Stanhope, C [Beaumont Health System, Royal Oak MI and Wayne State University, Detroit, MI (United States); Liang, J; Drake, D; Yan, D [Beaumont Health System, Royal Oak, MI (United States)

2016-06-15

Purpose: To determine the segment reduction and dose resolution necessary for machine log-files to effectively replace current phantom-based patient-specific quality assurance, while minimizing computational cost. Methods: Elekta’s Log File Convertor R3.2 records linac delivery parameters (dose rate, gantry angle, leaf position) every 40ms. Five VMAT plans [4 H&N, 1 Pulsed Brain] comprised of 2 arcs each were delivered on the ArcCHECK phantom. Log-files were reconstructed in Pinnacle on the phantom geometry using 1/2/3/4° control point spacing and 2/3/4mm dose grid resolution. Reconstruction effectiveness was quantified by comparing 2%/2mm gamma passing rates of the original and log-file plans. Modulation complexity scores (MCS) were calculated for each beam to correlate reconstruction accuracy and beam modulation. Percent error in absolute dose for each plan-pair combination (log-file vs. ArcCHECK, original vs. ArcCHECK, log-file vs. original) was calculated for each arc and every diode greater than 10% of the maximum measured dose (per beam). Comparing standard deviations of the three plan-pair distributions, relative noise of the ArcCHECK and log-file systems was elucidated. Results: The original plans exhibit a mean passing rate of 95.1±1.3%. The eight more modulated H&N arcs [MCS=0.088±0.014] and two less modulated brain arcs [MCS=0.291±0.004] yielded log-file pass rates most similar to the original plan when using 1°/2mm [0.05%±1.3% lower] and 2°/3mm [0.35±0.64% higher] log-file reconstructions respectively. Log-file and original plans displayed percent diode dose errors 4.29±6.27% and 3.61±6.57% higher than measurement. Excluding the phantom eliminates diode miscalibration and setup errors; log-file dose errors were 0.72±3.06% higher than the original plans – significantly less noisy. Conclusion: For log-file reconstructed VMAT arcs, 1° control point spacing and 2mm dose resolution is recommended, however, less modulated arcs may allow less

Determination of the geotechnical properties of mudrocks from geophysical logging of the Harwell boreholes

International Nuclear Information System (INIS)

Horseman, S.T.; McCann, D.M.; McEwen, T.J.; Brightman, M.A.

1984-11-01

The geotechnical properties of mainly argillaceous strata at depth in borehole HW3 at Harwell, Oxfordshire have been determined using a variety of borehole geophysical logging techniques. The aim of this work was to assess the usefulness of such techniques for the indirect measurement of the geotechnical properties of the rocks and the subsequent bearing that such knowledge would have on the design of a site investigation programme for the deep disposal of non heat emitting radioactive waste. The borehole was logged by Seismograph Services Ltd over the interval from 165 - 551 m., whilst open and mud filled. Seven different geophysical logs were run: caliper, formation density, neutron-neutron, natural-gamma, 3D velocity, spontaneous potential, single point resistance and 16''/64'' normal resistivity. The logs that were of any use in determining geotechnical properties were the neutron-neutron, the formation density and the sonic log. It is suggested that in these types of formation the sonic log, once calibrated for the particular circumstances, could be used to provide a useful downhole strength log. (author)

Drilling and associated drillhole measurements of the pilot hole ONK-PH10

International Nuclear Information System (INIS)

Mancini, P.; Karttunen, P.; Lokkila, M.; Pekkanen, J.; Poellaenen, J.; Tarvainen, A.-M.; Toropainen, V.; Kosunen, P.; Pere, T.

2010-08-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH10 was drilled from chainage 3459 to chainage 3639 in March 2009. The length of the hole is 180.00 metres. The drilling was done as orientated core drilling. The deviation of the drillhole was measured during and after the drilling phase. Electric conductivity was measured from the collected returning water samples. Logging of the core samples included the following parameters: lithology, foliation, fracturing, fracture frequency, RQD, fractured zones, core loss, and weathering. The rock mechanical logging was based on Q-classification. The test to determine rock strength and deformation were made with Rock Tester -equipment. Water conductivity of the fractures or fractured zones was measured by Posiva Flow Log equipment. The measurements were done in two phases. During flow measurements also grounding resistance electric conductivity and temperature were measured. In flow logging test, sections of 0.5 m with increments of 0.1 m were used. Water loss measurements were conducted in the hole section 3.70-180.00 m dhd. Geophysical logging and optical imaging of the pilot hole included the fieldwork of all surveys, the integration of the data as well as interpretation of the acoustic and drillhole radar data. One of the objectives of the geochemical study was to get information of the composition of

A Generally Applicable Computer Algorithm Based on the Group Additivity Method for the Calculation of Seven Molecular Descriptors: Heat of Combustion, LogPO/W, LogS, Refractivity, Polarizability, Toxicity and LogBB of Organic Compounds; Scope and Limits of Applicability

Directory of Open Access Journals (Sweden)

Rudolf Naef

2015-10-01

Full Text Available A generally applicable computer algorithm for the calculation of the seven molecular descriptors heat of combustion, logPoctanol/water, logS (water solubility, molar refractivity, molecular polarizability, aqueous toxicity (protozoan growth inhibition and logBB (log (cblood/cbrain is presented. The method, an extendable form of the group-additivity method, is based on the complete break-down of the molecules into their constituting atoms and their immediate neighbourhood. The contribution of the resulting atom groups to the descriptor values is calculated using the Gauss-Seidel fitting method, based on experimental data gathered from literature. The plausibility of the method was tested for each descriptor by means of a k-fold cross-validation procedure demonstrating good to excellent predictive power for the former six descriptors and low reliability of logBB predictions. The goodness of fit (Q2 and the standard deviation of the 10-fold cross-validation calculation was >0.9999 and 25.2 kJ/mol, respectively, (based on N = 1965 test compounds for the heat of combustion, 0.9451 and 0.51 (N = 2640 for logP, 0.8838 and 0.74 (N = 1419 for logS, 0.9987 and 0.74 (N = 4045 for the molar refractivity, 0.9897 and 0.77 (N = 308 for the molecular polarizability, 0.8404 and 0.42 (N = 810 for the toxicity and 0.4709 and 0.53 (N = 383 for logBB. The latter descriptor revealing a very low Q2 for the test molecules (R2 was 0.7068 and standard deviation 0.38 for N = 413 training molecules is included as an example to show the limits of the group-additivity method. An eighth molecular descriptor, the heat of formation, was indirectly calculated from the heat of combustion data and correlated with published experimental heat of formation data with a correlation coefficient R2 of 0.9974 (N = 2031.

Technology development for high temperature logging tools

Energy Technology Data Exchange (ETDEWEB)

Veneruso, A.F.; Coquat, J.A.

1979-01-01

A set of prototype, high temperature logging tools (temperature, pressure and flow) were tested successfully to temperatures up to 275/sup 0/C in a Union geothermal well during November 1978 as part of the Geothermal Logging Instrumentation Development Program. This program is being conducted by Sandia Laboratories for the Department of Energy's Division of Geothermal Energy. The progress and plans of this industry based program to develop and apply the high temperature instrumentation technology needed to make reliable geothermal borehole measurements are described. Specifically, this program is upgrading existing sondes for improved high temperature performance, as well as applying new materials (elastomers, polymers, metals and ceramics) and developing component technology such as high temperature cables, cableheads and electronics to make borehole measurements such as formation temperature, flow rate, high resolution pressure and fracture mapping. In order to satisfy critical existing needs, the near term goal is for operation up to 275/sup 0/C and 7000 psi by the end of FY80. The long term goal is for operation up to 350/sup 0/C and 20,000 psi by the end of FY84.

Witness sample preparation for measuring antireflection coatings.

Science.gov (United States)

Willey, Ronald R

2014-02-01

Measurement of antireflection coating of witness samples from across the worldwide industry has been shown to have excess variability from a sampling taken for the OSA Topical Meeting on Optical Interference Coatings: Measurement Problem. Various sample preparation techniques have been discussed with their limitations, and a preferred technique is recommended with its justification, calibration procedures, and limitations. The common practice of grinding the second side to reduce its reflection is less than satisfactory. One recommended practice is to paint the polished second side, which reduces its reflection to almost zero. A method to evaluate the suitability of given paints is also described.

Log canonical thresholds of smooth Fano threefolds

International Nuclear Information System (INIS)

Cheltsov, Ivan A; Shramov, Konstantin A

2008-01-01

The complex singularity exponent is a local invariant of a holomorphic function determined by the integrability of fractional powers of the function. The log canonical thresholds of effective Q-divisors on normal algebraic varieties are algebraic counterparts of complex singularity exponents. For a Fano variety, these invariants have global analogues. In the former case, it is the so-called α-invariant of Tian; in the latter case, it is the global log canonical threshold of the Fano variety, which is the infimum of log canonical thresholds of all effective Q-divisors numerically equivalent to the anticanonical divisor. An appendix to this paper contains a proof that the global log canonical threshold of a smooth Fano variety coincides with its α-invariant of Tian. The purpose of the paper is to compute the global log canonical thresholds of smooth Fano threefolds (altogether, there are 105 deformation families of such threefolds). The global log canonical thresholds are computed for every smooth threefold in 64 deformation families, and the global log canonical thresholds are computed for a general threefold in 20 deformation families. Some bounds for the global log canonical thresholds are computed for 14 deformation families. Appendix A is due to J.-P. Demailly.

GammaLog Playback 1.0 - mobile gamma ray spectrometry software

International Nuclear Information System (INIS)

Watson, R.J.; Smethurst, M.A.

2011-01-01

The Geological Survey of Norway (NGU) operates a mobile gamma ray spectrometer system which can be used in nuclear emergency situations to determine the location and type of orphan sources, or the extent and type of fallout contamination. The system consists of a 20 litre (16 litre downward and 4 litre upward looking) RSX-5 NaI detector and spectrometer, and can be mounted in fixed wing aircraft, helicopters, or vans/cars as appropriate. NGU has developed its own data acquisition and analysis software for this system. GammaLog (Smethurst 2005) controls the acquisition, display, and storage of data from the spectrometer, and performs real-time data analysis including estimation of dose rates and fallout concentrations, and separation of geological and anthropogenic components of the signal. The latter is particularly important where the geological radioisotope signal varies strongly from one place to another, and makes it easier to locate and identify anthropogenic sources which might otherwise be difficult to separate from the geological background signal. A modified version of GammaLog has been developed, GammaLog Playback, which allows the replay of previously acquired GammaLog datasets, while performing similar processing and display as the GammaLog acquisition software. This allows datasets to be reviewed and compared in the field or during post-survey analysis to help plan subsequent measurement strategies.(Au)

Accessing SAFOD data products: Downhole measurements, physical samples and long-term monitoring

Science.gov (United States)

Weiland, C.; Zoback, M.; Hickman, S. H.; Ellsworth, W. L.

2005-12-01

Many different types of data were collected during SAFOD Phases 1 and 2 (2004-2005) as part of the National Science Foundation's EarthScope program as well as from the SAFOD Pilot Hole, drilled in 2002 and funded by the International Continental Drilling Program (ICDP). Both SAFOD and the SAFOD Pilot Hole are being conducted as a close collaboration between NSF, the U.S. Geological Survey and the ICDP. SAFOD data products include cuttings, core and fluid samples; borehole geophysical measurements; and strain, tilt, and seismic recordings from the multilevel SAFOD borehole monitoring instruments. As with all elements of EarthScope, these data (and samples) are openly available to members of the scientific and educational communities. This paper presents the acquisition, storage and distribution plan for SAFOD data products. Washed and unwashed drill cuttings and mud samples were collected during Phases 1 and 2, along with three spot cores at depths of 1.5, 2.5, and 3.1 km. A total of 52 side-wall cores were also collected in the open-hole interval between 2.5 and 3.1 km depth. The primary coring effort will occur during Phase 3 (2007), when we will continuously core up to four, 250-m-long multilaterals directly within and adjacent to the San Andreas Fault Zone. Drill cuttings, core, and fluid samples from all three Phases of SAFOD drilling are being curated under carefully controlled conditions at the Integrated Ocean Drilling Program (IODP) Gulf Coast Repository in College Station, Texas. Photos of all physical samples and a downloadable sample request form are available on the ICDP website (http://www.icdp-online.de/sites/sanandreas/index/index.html). A suite of downhole geophysical measurements was conducted during the first two Phases of SAFOD drilling, as well as during drilling of the SAFOD Pilot Hole. These data include density, resistivity, porosity, seismic and borehole image logs and are also available via the ICDP website. The SAFOD monitoring program

Elephant logging and environment

International Nuclear Information System (INIS)

Tin-Aung-Hla

1995-01-01

The natural environment comprises non-biological elements such as air, water, light, heat and biological elements of animal and plant life; all interact with each other to create an ecosystem. Human activities like over-exploitation of forest results in deforestation and desertification. This consequently changes ecological balance. Topics on: (1) history of elephants utilization; (2) elephant logging; (3) classification of elephants; (4) dragging gear; (5) elephant power; (6) elephant logging and environment, are discussed

Financial feasibility of a log sort yard handling small-diameter logs: A preliminary study

Science.gov (United States)

Han-Sup Han; E. M. (Ted) Bilek; John (Rusty) Dramm; Dan Loeffler; Dave Calkin

2011-01-01

The value and use of the trees removed in fuel reduction thinning and restoration treatments could be enhanced if the wood were effectively evaluated and sorted for quality and highest value before delivery to the next manufacturing destination. This article summarizes a preliminary financial feasibility analysis of a log sort yard that would serve as a log market to...

Pembangkitan Data dari Distribusi Log-logistik

Directory of Open Access Journals (Sweden)

Aceng Komarudin Mutaqin

2014-11-01

Full Text Available Distribusi log-logistik merupakan salah satu distribusi yang dapat diaplikasikan untuk data mutu lingkungan. Makalah ini membahas pembangkitan data dari distribusi log-logistik mulai dari pembangunan algoritme sampai pembuatan program komputer pada perangkat lunak MATLAB. Metode pembangkitan datanya menggunakan metode inverse transform. Ada dua jenis data yang dibangkitkan, yaitu data lengkap dan data tersensor kiri. Dalam makalah ini diberikan contoh data yang dibangkitkan dari distribusi log-logistik.

Difference flow measurements in borehole KOV01 at Oskarshamn

International Nuclear Information System (INIS)

Poellaenen, J.; Rouhiainen, P.

2001-09-01

Posiva Flow Log/Difference Flow method can be used for relatively fast determination of hydraulic conductivity and hydraulic head in fractures or fractured zones in cored boreholes. This report presents the principles of the method as well as the results of the measurements carried out in borehole KOV01 at Oskarshamn in February and March 2001. The aim of the measurements presented in this report was to determine the depth and flow rate of flowing fractures in borehole KOV01 prior to groundwater sampling. The measurements in borehole KOV01 were carried out between 100-1000 m depth using the so called detailed flow logging mode; the flow rate into a 5 m long test section was measured. Detailed flow logging was repeated at the location of the detected flow anomalies using 0.5 m section length and 0.1 m point intervals. The borehole was pumped during these measurements. The occurrence of saline water in the borehole was studied by electric conductivity measurements. The flow guide encloses also an electrode for measuring of single point resistance of the bedrock. It was measured with 0.01 m point intervals during the detailed flow logging. Depth calibration was made on the basis of the known depth marks in the borehole. The depth marks were detected by caliper measurements and by single point resistance measurements

Development of a magnetic measurement device for thin ribbon samples

International Nuclear Information System (INIS)

Sato, Yuta; Todaka, Takashi; Enokizono, Masato

2008-01-01

This paper presents a magnetic measurement device for thin ribbon samples, which are produced by rapid cooling technique. This device enables us to measure magnetic properties easily by only inserting a ribbon sample into a sample holder. The sample holder was made by bakelite to fix any width sample. A long solenoid coil was used to generate a uniform magnetic field and the sample holder was placed at the mid part of the solenoid. The magnetic field strength was measured using a shunt resistor and the magnetic flux density and magnetization in sample ribbons were evaluated by using search coils. The accuracy of measurement was verified with an amorphous metal ribbon sample. Next, we have measured magnetic properties of some magnetic shape memory alloys, which have different compositions. The measured results are compared and we clarified the effect of Sm contents on the magnetic properties

Application of nuclear logging to porosity studies in Itaborai basin

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Milena F.S.; Lima, Inaya; Lopes, Ricardo Tadeu, E-mail: milena@lin.ufrj.br, E-mail: inaya@lin.ufrj.br, E-mail: ricardo@lin.ufrj.br [Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Instrumentacao Nuclear; Ferrucio, Paula Lucia; Borghi, Leonardo, E-mail: ferrucio@acd.ufrj.br, E-mail: borghi@ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Inst. de Geociencias. Dept. de Geologia; Abreu, Carlos Jorge, E-mail: jo_abreu@unb.br [Universidade de Brasilia (UnB), DF (Brazil). Inst. de Geociencias

2011-07-01

Nuclear logging provides information on bulk density and porosity variations by measuring the intensity of the scattered radiation induced on the formation by radioactive sources. In this study, nuclear logging was employed to analyze the pore-space system of the 2-ITAB-1-RJ well placed on the Itaborai limestone basin, in the state of Rio de Janeiro. This is one of the smallest sedimentary basin in Brazil and it is formed by clastic deposits and travertine limestone rocks which are fractured. Understanding the pore-space system of carbonate rocks has become important subject for the oil industry, specially in Brazil. A Density Gamma Probe (LSD) and a Neutron Probe (NEUT) were used for data acquisition, which nuclear logging was carried out in part of the well, with continuous detection for about 50 m of deep. The detection speed was 4 m/min for the LSD and 5 m/min for the NEUT. The results obtained by nuclear logging showed that the 2-ITAB-1-RJ well consists of three different intervals with rocks ranging from low to moderate porosity present in travertine, marls and gneisses. (author)

Plant inspection tours with mobile data logging system

International Nuclear Information System (INIS)

Roesser, U.

2006-01-01

The MDE Mobile Data Logging System has been introduced in a number of German power plants for efficient logging, evaluation, and quality-assured documentation of data recorded on plant inspection tours by means of pocket PCs instead of slips of paper. It will be installed in other nuclear power plants in the near future. The MDE system is composed of the pocket PCs for logging data during plant inspection tours, the associated docking stations installed in the respective areas of application, one PC or, if necessary, several PCs with the appropriate user software, and the associated network links. To install the software in the power plant, lists of rooms and measurement stations as well as other positions on an inspection course are transmitted to the MDE system. When the system has been commissioned, inspection tours are planned in accordance with past experience and optimized in the computer. User experience is taken into account in program updates. New functions improve user comfort and ease of evaluation. Additions to the MDE software, and applications in other areas, are tentatively planned and will be implemented as the need arises. (orig.)

Pulsed neutron logging - a modern approach to petroleum exploration

International Nuclear Information System (INIS)

Navalkar, M.P.

1978-01-01

As hydrocarbons have strikingly different properties for neutrons as compared with rocks, neutronic methods are useful to prepare logs of bore holes drilled for petroleum exploration. The earlier neutron logs were based on steady neutron sources, but the superior logs, namely, neutron life time log and neutron induced spectral log are based on pulsed neutron sources. The methods of obtaining these logs, their limitations and the field equipment required are described briefly. As the two logs are complementary, a plea has been made to develop field equipment which can obtain two logs in a single run. (M.G.B.)

Aggregation of log-linear risks

DEFF Research Database (Denmark)

Embrechts, Paul; Hashorva, Enkeleijd; Mikosch, Thomas Valentin

2014-01-01

In this paper we work in the framework of a k-dimensional vector of log-linear risks. Under weak conditions on the marginal tails and the dependence structure of a vector of positive risks, we derive the asymptotic tail behaviour of the aggregated risk {and present} an application concerning log...

Plutonium measurements in Hanford DOE site waste samples

International Nuclear Information System (INIS)

Dewberry, R.A.; Boyce, W.T.

1999-01-01

Development work to prepare a method to measure absolute 239 Pu content and Pu-isotopics by ICP-MS in acidified Hanford DOE-site samples which are very high in 90 Sr, 99 Tc, and 137 Cs radioactivity and which are frequently high in organic carbon content is described. Samples with very large 90 Sr and 137 Cs contents have historically been difficult to analyze for Pu content by each of three alpha-counting techniques in use at SRS, and analysis by ICP-MS in these samples is complicated by the high organics content. An ion exchange chemical preparation is reported to obtain fraction of Pu that does not contain any fission product contribution and no interfering organics to allow measure of absolute 239 Pu and of 239 Pu through 241 Pu isotopics by ICP-MS. The method uses a 242 Pu spike to measure Pu recovery and is demonstrated in this paper with three distinct commercially available resins and with over 300 samples. Measured absolute 239 Pu contents in sixty-three spiked/unspiked duplicates have agreed within 15% precision. Overall 242 Pu recoveries were near 90% with 25% precision. Comparisons of absolute 239 Pu contents measured directly on three samples agreed within the quoted 25% uncertainty. (author)

Comparison of fluvial suspended-sediment concentrations and particle-size distributions measured with in-stream laser diffraction and in physical samples

Science.gov (United States)

Czuba, Jonathan A.; Straub, Timothy D.; Curran, Christopher A.; Landers, Mark N.; Domanski, Marian M.

2015-01-01

Laser-diffraction technology, recently adapted for in-stream measurement of fluvial suspended-sediment concentrations (SSCs) and particle-size distributions (PSDs), was tested with a streamlined (SL), isokinetic version of the Laser In-Situ Scattering and Transmissometry (LISST) for measuring volumetric SSCs and PSDs ranging from 1.8-415 µm in 32 log-spaced size classes. Measured SSCs and PSDs from the LISST-SL were compared to a suite of 22 datasets (262 samples in all) of concurrent suspended-sediment and streamflow measurements using a physical sampler and acoustic Doppler current profiler collected during 2010-12 at 16 U.S. Geological Survey streamflow-gaging stations in Illinois and Washington (basin areas: 38 – 69,264 km2). An unrealistically low computed effective density (mass SSC / volumetric SSC) of 1.24 g/ml (95% confidence interval: 1.05-1.45 g/ml) provided the best-fit value (R2 = 0.95; RMSE = 143 mg/L) for converting volumetric SSC to mass SSC for over 2 orders of magnitude of SSC (12-2,170 mg/L; covering a substantial range of SSC that can be measured by the LISST-SL) despite being substantially lower than the sediment particle density of 2.67 g/ml (range: 2.56-2.87 g/ml, 23 samples). The PSDs measured by the LISST-SL were in good agreement with those derived from physical samples over the LISST-SL's measureable size range. Technical and operational limitations of the LISST-SL are provided to facilitate the collection of more accurate data in the future. Additionally, the spatial and temporal variability of SSC and PSD measured by the LISST-SL is briefly described to motivate its potential for advancing our understanding of suspended-sediment transport by rivers.

Experience in production works by X-ray radiometric logging to improve the confidence of borehole cross section sampling for zinc and lead

International Nuclear Information System (INIS)

Krasnoperov, V.A.; Zvujkovskij, Z.P.; Budnikov, F.G.; Sheleshko, R.P.

1977-01-01

An experiment on the application of roentgenoradiometric logging (RRL) for simultaneous determination of lead and zinc in prospecting boreholes is described. The measurements were made with a GKS-IH spectrometer equipped with modernized logging SP-4 probes of 42 mm in diameter with external units and CPM-19 counters. A radioactive armoured cable KRK-2 was used for transmitting information, the diagrams being recorded on an PR-6 photorecorder. The characteristic lines of the K-series of zinc and the L-series of lead, as well as singly scattered source radiation were recorded. The ranges of the recorded energies were 7-10, 10-15, and 18-21 keV. The spectrometer resolution for the zinc line was 20-23%. The portion of the integral spectrum of the working source with an energy of over 40 keV from the 87-keV line of cadmium-109 was used as a gamma reference. As a result of the investigation it was concluded that the sensitivity threshold of RRL is 3-5 times lower than the limiting content for overbalance ores and meets the prospecting requirements. The errors in the estimate of the contents and linear resources from RRL are commensurate with those of qualitative geological testing

Parental perceptions of the learner driver log book system in two Australian states.

Science.gov (United States)

Bates, Lyndel; Watson, Barry; King, Mark Johann

2014-01-01

Though many jurisdictions internationally now require learner drivers to complete a specified number of hours of supervised driving practice before being able to drive unaccompanied, very few require learner drivers to complete a log book to record this practice and then present it to the licensing authority. Learner drivers in most Australian jurisdictions must complete a log book that records their practice, thereby confirming to the licensing authority that they have met the mandated hours of practice requirement. These log books facilitate the management and enforcement of minimum supervised hours of driving requirements. Parents of learner drivers in 2 Australian states, Queensland and New South Wales, completed an online survey assessing a range of factors, including their perceptions of the accuracy of their child's learner log book and the effectiveness of the log book system. The study indicates that the large majority of parents believe that their child's learner log book is accurate. However, they generally report that the log book system is only moderately effective as a system to measure the number of hours of supervised practice a learner driver has completed. The results of this study suggest the presence of a paradox, with many parents possibly believing that others are not as diligent in the use of log books as they are or that the system is too open to misuse. Given that many parents report that their child's log book is accurate, this study has important implications for the development and ongoing monitoring of hours of practice requirements in graduated driver licensing systems.

Importance of the metrological network for calibration of neutron logging methods

International Nuclear Information System (INIS)

Rysavy, F.

1995-01-01

The calibration characteristics of neutron logging instrumentation are discussed. The principles of the rock, plastics, and water models are briefly outlined. Indian limestone of 9% porosity is the primary standard in the neutron logging metrology network, from which secondary standards employed during certification measurements are derived. It is recommended that rock blocks should be used as national standards, and each secondary institution should possess a set of polyethylene cylinders, one of which would serve as the main standard for the institution in question. (J.B.)

Log-inject-log in sand consolidation

International Nuclear Information System (INIS)

Murphy, R.P.; Spurlock, J.W.

1977-01-01

A method is described for gathering information for the determination of the adequacy of placement of sand consolidating plastic for sand control in oil and gas wells. The method uses a high neutron cross-section tracer which becomes part of the plastic and uses pulsed neutron logging before and after injection of the plastic. Preferably, the method uses lithium, boron, indium, and/or cadmium tracers. Boron oxide is especially useful and can be dissolved in alcohol and mixed with the plastic ingredients

Direct push driven in situ color logging tool (CLT): technique, analysis routines, and application

Science.gov (United States)

Werban, U.; Hausmann, J.; Dietrich, P.; Vienken, T.

2014-12-01

Direct push technologies have recently seen a broad development providing several tools for in situ parameterization of unconsolidated sediments. One of these techniques is the measurement of soil colors - a proxy information that reveals to soil/sediment properties. We introduce the direct push driven color logging tool (CLT) for real-time and depth-resolved investigation of soil colors within the visible spectrum. Until now, no routines exist on how to handle high-resolved (mm-scale) soil color data. To develop such a routine, we transform raw data (CIEXYZ) into soil color surrogates of selected color spaces (CIExyY, CIEL*a*b*, CIEL*c*h*, sRGB) and denoise small-scale natural variability by Haar and Daublet4 wavelet transformation, gathering interpretable color logs over depth. However, interpreting color log data as a single application remains challenging. Additional information, such as site-specific knowledge of the geological setting, is required to correlate soil color data to specific layers properties. Hence, we exemplary provide results from a joint interpretation of in situ-obtained soil color data and 'state-of-the-art' direct push based profiling tool data and discuss the benefit of additional data. The developed routine is capable of transferring the provided information obtained as colorimetric data into interpretable color surrogates. Soil color data proved to correlate with small-scale lithological/chemical changes (e.g., grain size, oxidative and reductive conditions), especially when combined with additional direct push vertical high resolution data (e.g., cone penetration testing and soil sampling). Thus, the technique allows enhanced profiling by means of providing another reproducible high-resolution parameter for analysis subsurface conditions. This opens potential new areas of application and new outputs for such data in site investigation. It is our intention to improve color measurements by means method of application and data

Logging while drilling keeps horizontal well on small target

International Nuclear Information System (INIS)

Leake, J.; Shray, F.

1991-01-01

This paper reports that the logging-while-drilling (LWD) measurement to two resistivities of different characteristics had led to a new interpretation method for the analysis of horizontal wells. By logging deep and shallow resistivity in real-time, marker beds were identified to help maintain well bore trajectory. The resistivity measurements were split into vertical and horizontal components to provide additional information of formation evaluation. In 1945, Ark Fuel Co. discovered and began developing the Olla field on the crest of the La Salle arch in La Salle Parish, La. Oil production comes from the Wilcox formation from alluvial sand packages that range in thickness from 3 ft to 120 ft. Now operated by Oxy U.S.A. Inc., Olla field was chosen in 1990 for a horizontal well pilot project. It was hoped that a horizontal well could alleviate water coming in one of the field's more productive sand packages- the 40-ft Cruse sand

29 CFR 1918.88 - Log operations.

Science.gov (United States)

2010-07-01

...) SAFETY AND HEALTH REGULATIONS FOR LONGSHORING Handling Cargo § 1918.88 Log operations. (a) Working in..., the employer shall ensure that employees remain clear of areas where logs being dumped could strike...

Methods for Sampling and Measurement of Compressed Air Contaminants

Energy Technology Data Exchange (ETDEWEB)

Stroem, L

1976-10-15

In order to improve the technique for measuring oil and water entrained in a compressed air stream, a laboratory study has been made of some methods for sampling and measurement. For this purpose water or oil as artificial contaminants were injected in thin streams into a test loop, carrying dry compressed air. Sampling was performed in a vertical run, down-stream of the injection point. Wall attached liquid, coarse droplet flow, and fine droplet flow were sampled separately. The results were compared with two-phase flow theory and direct observation of liquid behaviour. In a study of sample transport through narrow tubes, it was observed that, below a certain liquid loading, the sample did not move, the liquid remaining stationary on the tubing wall. The basic analysis of the collected samples was made by gravimetric methods. Adsorption tubes were used with success to measure water vapour. A humidity meter with a sensor of the aluminium oxide type was found to be unreliable. Oil could be measured selectively by a flame ionization detector, the sample being pretreated in an evaporation- condensation unit

Methods for Sampling and Measurement of Compressed Air Contaminants

International Nuclear Information System (INIS)

Stroem, L.

1976-10-01

In order to improve the technique for measuring oil and water entrained in a compressed air stream, a laboratory study has been made of some methods for sampling and measurement. For this purpose water or oil as artificial contaminants were injected in thin streams into a test loop, carrying dry compressed air. Sampling was performed in a vertical run, down-stream of the injection point. Wall attached liquid, coarse droplet flow, and fine droplet flow were sampled separately. The results were compared with two-phase flow theory and direct observation of liquid behaviour. In a study of sample transport through narrow tubes, it was observed that, below a certain liquid loading, the sample did not move, the liquid remaining stationary on the tubing wall. The basic analysis of the collected samples was made by gravimetric methods. Adsorption tubes were used with success to measure water vapour. A humidity meter with a sensor of the aluminium oxide type was found to be unreliable. Oil could be measured selectively by a flame ionization detector, the sample being pretreated in an evaporation- condensation unit

Drilling and the associated drillhole measurements of the pilot hole ONK-PH7

International Nuclear Information System (INIS)

Oehberg, A.; Kemppainen, K.; Lampinen, H.; Niemonen, J.; Poelloenen, J.; Rouhiainen, P.; Rautio, T.; Tarvainen, A.-M.

2007-12-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH7 was drilled from chainage 1880 to chainage 1980.31 in February 2007. The length of the hole is 100.31 m. The aim during the drilling work was to orient core samples as much as possible. The deviation of the drillhole was measured during and after the drilling phase. Electric conductivity was measured from the collected returning water samples. Logging of the core samples included the following parameters: lithology, foliation, fracturing, fracture frequency, RQD, fractured zones, core loss and weathering. The rock mechanical logging was based on Q-classification. The tests to determine rock strength and deformation properties were made with a Rock Tester-equipment. Difference Flow method was used for the determination of hydraulic conductivity in fractures and fractured zones in the drillhole. The overlapping i.e. the detailed flow logging mode was used. Besides flow logging Single Point Resistance (SPR), Electric Conductivity (EC) and temperature of the drillhole water were also measured. The flow logging was performed with 0.5 m section length and with 0.1 m depth increment. Water loss measurements were conducted between the hole depth of 1.18 m and the hole bottom. Geophysical logging and optical imaging of the pilot hole included the fieldwork of all surveys, the integration of the data as

Method and apparatus for logging inclined earth boreholes

International Nuclear Information System (INIS)

Youmans, A.H.

1981-01-01

An improved technique is provided for comparing the velocity of an elongated well logging instrument traversing an inclined earth borehole with the playout velocity of the well logging cable at the earth's surface to control both the cable hoist drum rotation and the rate of movement of the subsurface instrument and thus insure cable playout is in equilibrium with the logging instrument movement. Method and apparatus are described for detecting any reduction in movement of the logging instrument through the borehole and for reducing the velocity of the logging cable playout in response thereto by reducing drum rotation. Further, when the velocity of cable playout slows to a preselected value, a monitoring circuit generates control signals which actuate a means of power attached to or integral with the logging instrument which, upon initiation, apply a force to move the logging instrument upward or downward within the borehole

Log-concavity property for some well-known distributions

Directory of Open Access Journals (Sweden)

G. R. Mohtashami Borzadaran

2011-12-01

Full Text Available Interesting properties and propositions, in many branches of science such as economics have been obtained according to the property of cumulative distribution function of a random variable as a concave function. Caplin and Nalebuff (1988,1989, Bagnoli and Khanna (1989 and Bagnoli and Bergstrom (1989 , 1989, 2005 have discussed the log-concavity property of probability distributions and their applications, especially in economics. Log-concavity concerns twice differentiable real-valued function g whose domain is an interval on extended real line. g as a function is said to be log-concave on the interval (a,b if the function ln(g is a concave function on (a,b. Log-concavity of g on (a,b is equivalent to g'/g being monotone decreasing on (a,b or (ln(g" 6] have obtained log-concavity for distributions such as normal, logistic, extreme-value, exponential, Laplace, Weibull, power function, uniform, gamma, beta, Pareto, log-normal, Student's t, Cauchy and F distributions. We have discussed and introduced the continuous versions of the Pearson family, also found the log-concavity for this family in general cases, and then obtained the log-concavity property for each distribution that is a member of Pearson family. For the Burr family these cases have been calculated, even for each distribution that belongs to Burr family. Also, log-concavity results for distributions such as generalized gamma distributions, Feller-Pareto distributions, generalized Inverse Gaussian distributions and generalized Log-normal distributions have been obtained.

Review of magnetic susceptibility logging and its application to uranium exploration

International Nuclear Information System (INIS)

George, D.C.; Scott, J.H.

1982-01-01

Borehole measurement of magnetic susceptibility can show anomalies associated with mineralization or alteration. The detection of small anomalies is necessary, so efforts have been made in recent years to improve the sensitivity and the stability of magnetic susceptibility logging tools. Typical tools contain a single coil constructed as a solenoid wound on ferrite rods about 30cm long. The coil is heated to a constant temperature to reduce drift, and careful design is necessary to optimize temperature control and to maximize sensitivity. Measurements of coil resistance and inductance, which indicate conductivity and susceptibility, are made using a Maxwell bridge circuit. Circuit analysis shows that conductivity measurements are difficult and that stringent requirements are placed on phase stability of measurement circuitry. Corrections to the observed log are necessary to account for borehole size. The response of the tool to a thin zones of anomalous susceptibility is double peaked and a set of curves has been developed for interpretation. Calibrations of the tools are made by measuring the tool's response in models of known susceptibility

Environmental corrections of a dual-induction logging while drilling tool in vertical wells

Science.gov (United States)

Kang, Zhengming; Ke, Shizhen; Jiang, Ming; Yin, Chengfang; Li, Anzong; Li, Junjian

2018-04-01

With the development of Logging While Drilling (LWD) technology, dual-induction LWD logging is not only widely applied in deviated wells and horizontal wells, but it is used commonly in vertical wells. Accordingly, it is necessary to simulate the response of LWD tools in vertical wells for logging interpretation. In this paper, the investigation characteristics, the effects of the tool structure, skin effect and drilling environment of a dual-induction LWD tool are simulated by the three-dimensional (3D) finite element method (FEM). In order to closely simulate the actual situation, real structure of the tool is taking into account. The results demonstrate that the influence of the background value of the tool structure can be eliminated. The values of deducting the background of a tool structure and analytical solution have a quantitative agreement in homogeneous formations. The effect of measurement frequency could be effectively eliminated by chart of skin effect correction. In addition, the measurement environment, borehole size, mud resistivity, shoulder bed, layer thickness and invasion, have an effect on the true resistivity. To eliminate these effects, borehole correction charts, shoulder bed correction charts and tornado charts are computed based on real tool structure. Based on correction charts, well logging data can be corrected automatically by a suitable interpolation method, which is convenient and fast. Verified with actual logging data in vertical wells, this method could obtain the true resistivity of formation.

High-temperature ultrasonic measurements applied to directly heated samples

International Nuclear Information System (INIS)

Moore, R.I.; Taylor, R.E.

1984-01-01

High-temperature ultrasonic measurements of Young's modulus were made of graphite samples heated directly. The samples were cylindrical rods of the same geometry as that used in the multiproperty apparatus for simultaneous/consecutive measurements of a number of thermophysical properties to high temperatures. The samples were resonated in simple longitudinal vibration modes. Measurements were performed up to 2000 K. Incorporation of ultrasonic measurements of Young's modulus in the capabilities of the multiproperty apparatus is valuable because (i) ultrasonic measurements can be related to normal destructive measurements of this property; (ii) they can be used for screening materials or acceptance testing of specimens; (iii) they can be used to increase the understanding of thermophysical properties and property correlations. (author)

Radon measurement in Malaysia water samples

International Nuclear Information System (INIS)

Ibrahim, A.B.; Rosli Mahat; Yusof Md Amin

1995-01-01

This paper reported the results of the measurement of radon in local water. The water samples collected were rainwater, river water, seawater, well water or ground water at area of State of Selangor and Kuala Lumpur. The samples were collected in scintillation cell ZnS(Ag) through Radon Degassing Unit RDU 200. Alpha activity was counted with scintillation counters RD 200 at energy 5.5 MeV. (author)

Metaheuristic optimization approaches to predict shear-wave velocity from conventional well logs in sandstone and carbonate case studies

Science.gov (United States)

Emami Niri, Mohammad; Amiri Kolajoobi, Rasool; Khodaiy Arbat, Mohammad; Shahbazi Raz, Mahdi

2018-06-01

Seismic wave velocities, along with petrophysical data, provide valuable information during the exploration and development stages of oil and gas fields. The compressional-wave velocity (VP ) is acquired using conventional acoustic logging tools in many drilled wells. But the shear-wave velocity (VS ) is recorded using advanced logging tools only in a limited number of wells, mainly because of the high operational costs. In addition, laboratory measurements of seismic velocities on core samples are expensive and time consuming. So, alternative methods are often used to estimate VS . Heretofore, several empirical correlations that predict VS by using well logging measurements and petrophysical data such as VP , porosity and density are proposed. However, these empirical relations can only be used in limited cases. The use of intelligent systems and optimization algorithms are inexpensive, fast and efficient approaches for predicting VS. In this study, in addition to the widely used Greenberg–Castagna empirical method, we implement three relatively recently developed metaheuristic algorithms to construct linear and nonlinear models for predicting VS : teaching–learning based optimization, imperialist competitive and artificial bee colony algorithms. We demonstrate the applicability and performance of these algorithms to predict Vs using conventional well logs in two field data examples, a sandstone formation from an offshore oil field and a carbonate formation from an onshore oil field. We compared the estimated VS using each of the employed metaheuristic approaches with observed VS and also with those predicted by Greenberg–Castagna relations. The results indicate that, for both sandstone and carbonate case studies, all three implemented metaheuristic algorithms are more efficient and reliable than the empirical correlation to predict VS . The results also demonstrate that in both sandstone and carbonate case studies, the performance of an artificial bee

A comparison of dried shiitake mushroom in log cultivation and mycelial cultivation from different geographical origins using stable carbon and nitrogen isotope analysis

International Nuclear Information System (INIS)

Suzuki, Yaeko; Nakashita, Rumiko; Ishikawa, Noemia Kazue; Tabuchi, Akiko; Sakuno, Emi; Tokimoto, Keisuke

2015-01-01

We determined carbon and nitrogen isotopic compositions (δ 13 C and δ 15 N) of dried shiitake mushroom (Lentinula edodes) samples from Japan, China, South Korea and Brazil in order to discriminate their geographical origins. In log cultivation, the δ 13 C values of Japanese dried shiitake samples were lower than those of Chinese samples, depending on the δ 13 C values of log and their growth conditions. In mycelial cultivation, the δ 13 C and δ 15 N values of Japanese dried shiitake samples were higher than those of Chinese samples. By using the δ 13 C and δ 15 N values, 87.4% of Japanese dried shiitake samples (n = 95) and 87.9% of Chinese dried shiitake samples (n = 66) in log cultivation, 90.0% of the Japanese dried shiitake samples (n = 50) and 93.9% of Chinese dried shiitake samples (n = 114) in mycelial cultivation, were correctly classified according to the production site. These results suggested that the δ 13 C and δ 15 N values will be potentially useful for tracing their geographical origin of dried shiitake samples. (author)

An innovative OSCE clinical log station: a quantitative study of its influence on Log use by medical students

Directory of Open Access Journals (Sweden)

Hudson Judith N

2012-11-01

Full Text Available Abstract Background A Clinical Log was introduced as part of a medical student learning portfolio, aiming to develop a habit of critical reflection while learning was taking place, and provide feedback to students and the institution on learning progress. It was designed as a longitudinal self-directed structured record of student learning events, with reflection on these for personal and professional development, and actions planned or taken for learning. As incentive was needed to encourage student engagement, an innovative Clinical Log station was introduced in the OSCE, an assessment format with established acceptance at the School. This study questions: How does an OSCE Clinical Log station influence Log use by students? Methods The Log station was introduced into the formative, and subsequent summative, OSCEs with careful attention to student and assessor training, marking rubrics and the standard setting procedure. The scoring process sought evidence of educational use of the log, and an ability to present and reflect on key learning issues in a concise and coherent manner. Results Analysis of the first cohort’s Log use over the four-year course (quantified as number of patient visits entered by all students revealed limited initial use. Usage was stimulated after introduction of the Log station early in third year, with some improvement during the subsequent year-long integrated community-based clerkship. Student reflection, quantified by the mean number of characters in the ‘reflection’ fields per entry, peaked just prior to the final OSCE (mid-Year 4. Following this, very few students continued to enter and reflect on clinical experience using the Log. Conclusion While the current study suggested that we can’t assume students will self-reflect unless such an activity is included in an assessment, ongoing work has focused on building learner and faculty confidence in the value of self-reflection as part of being a competent

Conservative Sample Size Determination for Repeated Measures Analysis of Covariance.

Science.gov (United States)

Morgan, Timothy M; Case, L Douglas

2013-07-05

In the design of a randomized clinical trial with one pre and multiple post randomized assessments of the outcome variable, one needs to account for the repeated measures in determining the appropriate sample size. Unfortunately, one seldom has a good estimate of the variance of the outcome measure, let alone the correlations among the measurements over time. We show how sample sizes can be calculated by making conservative assumptions regarding the correlations for a variety of covariance structures. The most conservative choice for the correlation depends on the covariance structure and the number of repeated measures. In the absence of good estimates of the correlations, the sample size is often based on a two-sample t-test, making the 'ultra' conservative and unrealistic assumption that there are zero correlations between the baseline and follow-up measures while at the same time assuming there are perfect correlations between the follow-up measures. Compared to the case of taking a single measurement, substantial savings in sample size can be realized by accounting for the repeated measures, even with very conservative assumptions regarding the parameters of the assumed correlation matrix. Assuming compound symmetry, the sample size from the two-sample t-test calculation can be reduced at least 44%, 56%, and 61% for repeated measures analysis of covariance by taking 2, 3, and 4 follow-up measures, respectively. The results offer a rational basis for determining a fairly conservative, yet efficient, sample size for clinical trials with repeated measures and a baseline value.

Effects of salvage logging and pile-and-burn on fuel loading, potential fire behaviour, fuel consumption and emissions

Science.gov (United States)

Morris C. Johnson; Jessica E. Halofsky; David L. Peterson

2013-01-01

We used a combination of field measurements and simulation modelling to quantify the effects of salvage logging, and a combination of salvage logging and pile-and-burn fuel surface fuel treatment (treatment combination), on fuel loadings, fire behaviour, fuel consumption and pollutant emissions at three points in time: post-windstorm (before salvage logging), post-...

La competitividad logística en Latinoamérica: índice logístico vs. propuesta metodológica

Directory of Open Access Journals (Sweden)

Marco Alberto Valenzo Jiménez

2016-02-01

Full Text Available Este artículo muestra la situación actual de la competitividad logística en los países latinoamericanos, tomando como base el informe denominado “Connecting to Compite” (Trade Logistics in the Global Economy, 2007 del Banco Mundial. Este informe muestra el ranking de las posiciones que tienen los países latinoamericanos en materia de logística y en el cual se analizan las variables —aduanas, infraestructura, embarques internacionales, competencia logística, trazabilidad y seguimiento, costos logísticos domésticos y tiempo de entrega— que contiene la metodología utilizada por el Banco Mundial. La plataforma de estudio de este artículo parte del índice de competitividad logística, que, mediante la aplicación de la metodología “Valenzo – Martínez” permite analizar la base de datos de una manera más profunda, y da como resultado una escala de competitividad logística que nos muestra el nivel general de la competitividad logística en Latinoamérica, así como también el nivel de competitividad por variable, para, de esta manera, permitir una fácil interpretación de los resultados.

Neutron-neutron-resonance logging of boron in boreholes with the use of the PRKS-2 radiometer

International Nuclear Information System (INIS)

Vakhtin, B.S.; Ivanov, V.S.; Filippov, E.M.; Novoselov, A.V.

1973-01-01

The well rig of the PRKS-2 logging radiometer is supplemented with a probe device for neutron measurements permitting to vary the probe size from 20 to 45 cm. To decrease the natural gamma radiation effect an external lead shield 7-mm thick having 50-mm outer diameter is fixed on the instrument sleeve. The instrument is provided with a NaI detector and a set of foils of Cd, Ag, Rh, Tu, In, Ta, and a Pu-Be source of 1x10 6 n/sec strength. The optimal size of the probe is assumed as 25 cm. From the results of well measurements a better differentiation of neutron resonance logging was noticed in comparison with neutron gamma logging. Comparing the data obtained with those of kern analysis a calibration curve was derived of neutron resonance logging versus B for wells of 59 mm dia

Selective logging and its relation to deforestation

Science.gov (United States)

Gregory P. Asner; Michael Keller; Marco Lentini; Frank Merry; Souza Jr. Carlos

2009-01-01

Selective logging is a major contributor to the social, economic, and ecological dynamics of Brazilian Amazonia. Logging activities have expanded from low-volume floodplain harvests in past centuries to high-volume operations today that take about 25 million m3 of wood from the forest each year. The most common high-impact conventional and often illegal logging...

Results of tritium measurement in environmental samples and drainage

International Nuclear Information System (INIS)

Koike, Ryoji; Hirai, Yasuo

1983-01-01

In Ibaraki prefecture, the tritium concentration in the drainage from the nuclear facilities has been measured since 1974. Then, with the start of operation of the fuel reprocessing plant in 1977, the tritium concentration in environmental samples was to be measured also in order to examine the effect of the drainage on the environment. The results of the tritium measurement in Ibaraki prefecture up to about 1980 are described: sampling points, sampling and measuring methods, the tritium concentration in the drainage, air, inland water and seawater, respectively. The drainages have been taken from Japan Atomic Power Company, Japan Atomic Energy Research Institute, and Power Reactor and Nuclear Fuel Development Corporation (with the fuel reprocessing plant). The samples of air, inland water and seawater have been taken in the areas concerned. The tritium concentration was measured by a low-background liquid scintillation counter. The measured values in the environment have been generally at low level, not different from other areas. (Mori, K.)

Crowded letter and crowded picture logMAR acuity in children with amblyopia: a quantitative comparison.

Science.gov (United States)

O'Boyle, Cathy; Chen, Sean I; Little, Julie-Anne

2017-04-01

Clinically, picture acuity tests are thought to overestimate visual acuity (VA) compared with letter tests, but this has not been systematically investigated in children with amblyopia. This study compared VA measurements with the LogMAR Crowded Kay Picture test to the LogMAR Crowded Keeler Letter acuity test in a group of young children with amblyopia. 58 children (34 male) with amblyopia (22 anisometropic, 18 strabismic and 18 with both strabismic/anisometropic amblyopia) aged 4-6 years (mean=68.7, range=48-83 months) underwent VA measurements. VA chart testing order was randomised, but the amblyopic eye was tested before the fellow eye. All participants wore up-to-date refractive correction. The Kay Picture test significantly overestimated VA by 0.098 logMAR (95% limits of agreement (LOA), 0.13) in the amblyopic eye and 0.088 logMAR (95% LOA, 0.13) in the fellow eye, respectively (pocclusion therapy, refractive correction or type of amblyopia on VA results (p>0.23). For both the amblyopic and fellow eyes, Bland-Altman plots demonstrated a systematic and predictable difference between Kay Picture and Keeler Letter charts across the range of acuities tested (Keeler acuity: amblyopic eye 0.75 to -0.05 logMAR; fellow eye 0.45 to -0.15 logMAR). Linear regression analysis (pamblyopia. Due to the predictable difference found between both crowded logMAR acuity tests, it is reasonable to adjust Kay Picture acuity thresholds by +0.10 logMAR to compute expected Keeler Letter acuity scores. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Measurements of astrophysical reaction rates for radioactive samples

International Nuclear Information System (INIS)

Koehler, P.E.; O'Brien, H.A.; Bowman, C.D.

1987-01-01

Reaction rates for both big-bang and stellar nucleosynthesis can be obtained from the measurement of (n,p) and (n,γ) cross sections for radioactive nuclei. In the past, large backgrounds associated with the sample activity limited these types of measurements to radioisotopes with very long half lives. The advent of the low-energy, high-intensity neutron source at the Los Alamos Neutron Scattering CEnter (LANSCE) has greatly increased the number of nuclei which can be studied. Results of (n,p) measurements on samples with half lives as short as fifty-three days will be given. The astrophysics to be learned from these data will be discussed. Additional difficulties are encountered when making (n,γ) rather than (n,p) measurements. However, with a properly designed detector, and with the high peak neutron intensities now available, (n,γ) measurements can be made for nuclei with half lives as short as several weeks. Progress on the Los Alamos (n,γ) cross-section measurement program for radioactive samples will be discussed. 25 refs., 3 figs., 1 tab

Fundamentals of Acoustic Measurements on Trees and Logs and Their Implication to Field Application

Science.gov (United States)

Xiping Wang

2011-01-01

Acoustic technologies have been well established as material evaluation tools in the past several decades, and their use has become widely accepted in the forest products industry for on-line quality control and products grading. Recent research developments on acoustic sensing technology offer further opportunities to evaluate standing trees and logs for general wood...

Mud Logging; Control geologico en perforaciones petroliferas (Mud Logging)

Energy Technology Data Exchange (ETDEWEB)

Pumarega Lafuente, J.C.

1994-12-31

Mud Logging is an important activity in the oil field and it is a key job in drilling operations, our duties are the acquisition, collection and interpretation of the geological and engineering data at the wellsite, also inform the client immediately of any significant changes in the well. (Author)

Mariners Weather Log

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Mariners Weather Log (MWL) is a publication containing articles, news and information about marine weather events and phenomena, worldwide environmental impact...

Development of response transforms from comparative study of commercial pulsed neutron capture logging systems

International Nuclear Information System (INIS)

Salaita, G.N.; Youngblood, W.E.

1991-01-01

This paper reports that the absence of a common calibration facility to ascertain the accuracy of commercial pulsed neutron capture logging systems, coupled with the desire for more accurate saturation determination from time-lapse logs, prompted Saudi Aramco to carry out this comparative study. Three generations of Schlumberger's Thermal Decay Time (TDT) logging devices, viz., TDT-K, TDT-M, and TDT-P along with Atlas Wireline PDK-100 system were run in an Aramco well. The wellbore 8-1/2 inch with 7-inch casing-penetrated clean sand, shaly sand, and shale streaks sequence as exhibited by the open hole natural gamma ray log. initially, the wellbore fluid was diesel. The fluid was then changed to brines of 42-kppm and 176-kppm NACl, respectively. Three repeat passes at a logging speed of 900 ft/hr were obtained by each device for each of the three borehole liquids. In the case of PDK-100, a second set of log runs was obtained at 1800 ft/hr. The results of this extensive comparative study have increased the author's understanding of the borehole liquid and the diffusion effects on the response of pulsed neutron capture logging systems and also on the relative accuracy and precision of measured formation thermal neutron capture cross section by each system

Calculating tissue shear modulus and pressure by 2D log-elastographic methods

International Nuclear Information System (INIS)

McLaughlin, Joyce R; Zhang, Ning; Manduca, Armando

2010-01-01

Shear modulus imaging, often called elastography, enables detection and characterization of tissue abnormalities. In this paper the data are two displacement components obtained from successive MR or ultrasound data sets acquired while the tissue is excited mechanically. A 2D plane strain elastic model is assumed to govern the 2D displacement, u. The shear modulus, μ, is unknown and whether or not the first Lamé parameter, λ, is known the pressure p = λ∇ . u which is present in the plane strain model cannot be measured and is unreliably computed from measured data and can be shown to be an order one quantity in the units kPa. So here we present a 2D log-elastographic inverse algorithm that (1) simultaneously reconstructs the shear modulus, μ, and p, which together satisfy a first-order partial differential equation system, with the goal of imaging μ; (2) controls potential exponential growth in the numerical error and (3) reliably reconstructs the quantity p in the inverse algorithm as compared to the same quantity computed with a forward algorithm. This work generalizes the log-elastographic algorithm in Lin et al (2009 Inverse Problems 25) which uses one displacement component, is derived assuming that the component satisfies the wave equation and is tested on synthetic data computed with the wave equation model. The 2D log-elastographic algorithm is tested on 2D synthetic data and 2D in vivo data from Mayo Clinic. We also exhibit examples to show that the 2D log-elastographic algorithm improves the quality of the recovered images as compared to the log-elastographic and direct inversion algorithms

Sediment pathways in a tropical forest: effects of logging roads and skid trails

Science.gov (United States)

Sidle, Roy C.; Sasaki, Shozo; Otsuki, Mieko; Noguchi, Shoji; Rahim Nik, Abdul

2004-03-01

Significant erosion occurred from recently constructed forest logging roads and skid trails in a small headwater catchment in Peninsular Malaysia. Soil loss was estimated by measuring dimensions of all significant rills and gullies along the road, as well as by measuring height of preserved soil pedestals in sidecast and fill material and on skid trails. Estimates of surface erosion from logging roads and skid trails were 272 +/- 20 t ha-1 year-1 and 275 +/- 20 t ha-1 year-1 respectively. However, owing to lack of connectivity of skid trails to the stream, much of the sediment mobilized on skid trails was stored either on adjacent hillslopes or the trails themselves, rather than being transported to the stream system, as was the case for the road. Steeper skid trails (>20% gradient) had slightly higher erosion rates (320 +/- 24 t ha-1 year-1) than trails with gentler gradients (245-264 t ha-1 year-1). Some 60% of the soil loss on logging roads comes from erosion of the running surface. Disturbed cut and fill material along the road supplied the remaining 40% of the soil loss from roads. Roads and skid trails had no designed drainage systems; runoff discharged onto the hillslope at 25 major discharge nodes from the logging road (690 m total length) and at 34 nodes from skid trails (2300 m). Sediment pathways were either fully or moderately connected to headwater channels at 64% of the logging road nodes, but at only 26% of the nodes emanating from skid trails. A detailed sediment budget revealed that 78% of the soil loss from the road system (including log landings) was delivered to the stream in the first 16 months after logging began. Most (90%) of the deposition from skid trails occurred below just three discharge nodes. Runoff from and onto skid trails often exacerbated the sediment connectivity to channels. Clearly, sediment discharge from logging roads was more highly connected to the stream than discharge from skid trails. Once in the channel, much of this

Log-normality of indoor radon data in the Walloon region of Belgium

International Nuclear Information System (INIS)

Cinelli, Giorgia; Tondeur, François

2015-01-01

The deviations of the distribution of Belgian indoor radon data from the log-normal trend are examined. Simulated data are generated to provide a theoretical frame for understanding these deviations. It is shown that the 3-component structure of indoor radon (radon from subsoil, outdoor air and building materials) generates deviations in the low- and high-concentration tails, but this low-C trend can be almost completely compensated by the effect of measurement uncertainties and by possible small errors in background subtraction. The predicted low-C and high-C deviations are well observed in the Belgian data, when considering the global distribution of all data. The agreement with the log-normal model is improved when considering data organised in homogeneous geological groups. As the deviation from log-normality is often due to the low-C tail for which there is no interest, it is proposed to use the log-normal fit limited to the high-C half of the distribution. With this prescription, the vast majority of the geological groups of data are compatible with the log-normal model, the remaining deviations being mostly due to a few outliers, and rarely to a “fat tail”. With very few exceptions, the log-normal modelling of the high-concentration part of indoor radon data is expected to give reasonable results, provided that the data are organised in homogeneous geological groups. - Highlights: • Deviations of the distribution of Belgian indoor Rn data from the log-normal trend. • 3-component structure of indoor Rn: subsoil, outdoor air and building materials. • Simulated data generated to provide a theoretical frame for understanding deviations. • Data organised in homogeneous geological groups; better agreement with the log-normal

New Technique for TOC Estimation Based on Thermal Core Logging in Low-Permeable Formations (Bazhen fm.)

Science.gov (United States)

Popov, Evgeny; Popov, Yury; Spasennykh, Mikhail; Kozlova, Elena; Chekhonin, Evgeny; Zagranovskaya, Dzhuliya; Belenkaya, Irina; Alekseev, Aleksey

2016-04-01

A practical method of organic-rich intervals identifying within the low-permeable dispersive rocks based on thermal conductivity measurements along the core is presented. Non-destructive non-contact thermal core logging was performed with optical scanning technique on 4 685 full size core samples from 7 wells drilled in four low-permeable zones of the Bazhen formation (B.fm.) in the Western Siberia (Russia). The method employs continuous simultaneous measurements of rock anisotropy, volumetric heat capacity, thermal anisotropy coefficient and thermal heterogeneity factor along the cores allowing the high vertical resolution (of up to 1-2 mm). B.fm. rock matrix thermal conductivity was observed to be essentially stable within the range of 2.5-2.7 W/(m*K). However, stable matrix thermal conductivity along with the high thermal anisotropy coefficient is characteristic for B.fm. sediments due to the low rock porosity values. It is shown experimentally that thermal parameters measured relate linearly to organic richness rather than to porosity coefficient deviations. Thus, a new technique employing the transformation of the thermal conductivity profiles into continuous profiles of total organic carbon (TOC) values along the core was developed. Comparison of TOC values, estimated from the thermal conductivity values, with experimental pyrolytic TOC estimations of 665 samples from the cores using the Rock-Eval and HAWK instruments demonstrated high efficiency of the new technique for the organic rich intervals separation. The data obtained with the new technique are essential for the SR hydrocarbon generation potential, for basin and petroleum system modeling application, and estimation of hydrocarbon reserves. The method allows for the TOC richness to be accurately assessed using the thermal well logs. The research work was done with financial support of the Russian Ministry of Education and Science (unique identification number RFMEFI58114X0008).

Pacific Rim log trade: determinants and trends.

Science.gov (United States)

Donald F. Flora; Andrea L. Anderson; Wendy J. McGinnls

1991-01-01

Pacific Rim trade in softwood logs amounts to about $3 billion annually, of which the U.S. share is about $2 billion. Log exporting is a significant part of the forest economy in the Pacific Northwest. The 10 major Pacific Rim log-trading client and competitor countries differ widely in their roles in trade and in their policies affecting the industry.

36Cl measurements of Hiroshima concrete samples

International Nuclear Information System (INIS)

Matsuhiro, T.; Nagashima, Y.; Seki, R.; Takahashi, T.

2002-01-01

The 36 Cl AMS studies are reported. A new steps of procedure of a sample preparation is developed and a tremendous reduction of sulphur background has been achieved. The 36 Cl contents of two atomic bombed concrete samples, old Hiroshima Bank one and Gokoku Shrine one, have been measured as a function of 36 Cl to Cl ratio by the Tsukuba AMS system. The 36 Cl to Cl ratio of the old Hiroshima Bank sample shows very nice agreement with the result of γ measurement of 152 Eu. Otherwise, the ratio is about 20% smaller than an estimation by the DS86 dosimetry system. A result of the Gokoku Shrine sample is also smaller than a depth profile estimation by the same DS86. It might be clear that the DS86 has a tendency of overestimation. It seems that a calculation method and/or the parameters used in the calculation are requested to be improved. (author)

Log Analysis Using Splunk Hadoop Connect

Science.gov (United States)

2017-06-01

23 A. INPUT SELECTION ...Conversion Resource Consumption .............................................. 28 Figure 8. Distribution of Events in Years...running a logging service puts a performance tax on the system and may cause the degradation of performance. More thorough 8 logging will cause a

Experimental approaches for the development of gamma spectroscopy well logging system

Energy Technology Data Exchange (ETDEWEB)

Shin, Jehyun; Hwang, Seho; Kim, Jongman [Korea Institute of Geoscience and Mineral Resources (124 Gwahang-no, Yuseong-gu, Daejeon, Korea) (Korea, Republic of); Won, Byeongho [Heesong Geotek Co., Ltd (146-8 Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea) (Korea, Republic of)

2015-03-10

This article discusses experimental approaches for the development of gamma spectroscopy well logging system. Considering the size of borehole sonde, we customize 2 x 2 inches inorganic scintillators and the system including high voltage, preamplifier, amplifier and multichannel analyzer (MCA). The calibration chart is made by test using standard radioactive sources so that the measured count rates are expressed by energy spectrum. Optimum high-voltage supplies and the measurement parameters of each detector are set up by experimental investigation. Also, the responses of scintillation detectors have been examined by analysis according to the distance between source and detector. Because gamma spectroscopy well logging needs broad spectrum, high sensitivity and resolution, the energy resolution and sensitivity as a function of gamma ray energy are investigated by analyzing the gamma ray activities of the radioactive sources.

Selective logging: does the imprint remain on tree structure and composition after 45 years?

Science.gov (United States)

Osazuwa-Peters, Oyomoare L.; Chapman, Colin A.; Zanne, Amy E.

2015-01-01

Selective logging of tropical forests is increasing in extent and intensity. The duration over which impacts of selective logging persist, however, remains an unresolved question, particularly for African forests. Here, we investigate the extent to which a past selective logging event continues to leave its imprint on different components of an East African forest 45 years later. We inventoried 2358 stems ≥10 cm in diameter in 26 plots (200 m × 10 m) within a 5.2 ha area in Kibale National Park, Uganda, in logged and unlogged forest. In these surveys, we characterized the forest light environment, taxonomic composition, functional trait composition using three traits (wood density, maximum height and maximum diameter) and forest structure based on three measures (stem density, total basal area and total above-ground biomass). In comparison to unlogged forests, selectively logged forest plots in Kibale National Park on average had higher light levels, different structure characterized by lower stem density, lower total basal area and lower above-ground biomass, and a distinct taxonomic composition driven primarily by changes in the relative abundance of species. Conversely, selectively logged forest plots were like unlogged plots in functional composition, having similar community-weighted mean values for wood density, maximum height and maximum diameter. This similarity in functional composition irrespective of logging history may be due to functional recovery of logged forest or background changes in functional attributes of unlogged forest. Despite the passage of 45 years, the legacy of selective logging on the tree community in Kibale National Park is still evident, as indicated by distinct taxonomic and structural composition and reduced carbon storage in logged forest compared with unlogged forest. The effects of selective logging are exerted via influences on tree demography rather than functional trait composition. PMID:27293697

Neutron die-away well logging

International Nuclear Information System (INIS)

Jacobson, L.A.

1976-01-01

Neutron die-away well logging is extensively used for the location and monitoring of hydrocarbon zones in cased wells. Casing prohibits the use of conventional open-hole electrical resistivity methods. Through an appropriate interpretation of the measured capture cross-section, it is possible to determine the fractional hydrocarbon content of the rock pore volume, provided that the interstitial water is moderately saline (Σ/sub w/ greater than or equal to .035 cm -1 ). Special sealed D-T accelerator tubes and high voltage supplies have been developed for this purpose. They must fit into a 25 mm design circle and operate at 175 0 C, producing approximately 10 8 neutron/sec average in repetitive bursts. In the Schlumberger method an electronic servo-system adjusts burst and measure-gate timing to minimize statistical uncertainty regardless of die-away time

Log and tree sawing times for hardwood mills

Science.gov (United States)

Everette D. Rast

1974-01-01

Data on 6,850 logs and 1,181 trees were analyzed to predict sawing times. For both logs and trees, regression equations were derived that express (in minutes) sawing time per log or tree and per Mbf. For trees, merchantable height is expressed in number of logs as well as in feet. One of the major uses for the tables of average sawing times is as a bench mark against...

Statistical sampling for holdup measurement

International Nuclear Information System (INIS)

Picard, R.R.; Pillay, K.K.S.

1986-01-01

Nuclear materials holdup is a serious problem in many operating facilities. Estimating amounts of holdup is important for materials accounting and, sometimes, for process safety. Clearly, measuring holdup in all pieces of equipment is not a viable option in terms of time, money, and radiation exposure to personnel. Furthermore, 100% measurement is not only impractical but unnecessary for developing estimated values. Principles of statistical sampling are valuable in the design of cost effective holdup monitoring plans and in qualifying uncertainties in holdup estimates. The purpose of this paper is to describe those principles and to illustrate their use

SU-F-T-469: A Clinically Observed Discrepancy Between Image-Based and Log- Based MLC Position

Energy Technology Data Exchange (ETDEWEB)

Neal, B; Ahmed, M; Siebers, J [University of Virginia Health System, Charlottesville, VA (United States)

2016-06-15

Purpose: To present a clinical case which challenges the base assumption of log-file based QA, by showing that the actual position of a MLC leaf can suddenly deviate from its programmed and logged position by >1 mm as observed with real-time imaging. Methods: An EPID-based exit-fluence dosimetry system designed to prevent gross delivery errors was used in cine mode to capture portal images during treatment. Visual monitoring identified an anomalous MLC leaf pair gap not otherwise detected by the automatic position verification. The position of the erred leaf was measured on EPID images and log files were analyzed for the treatment in question, the prior day’s treatment, and for daily MLC test patterns acquired on those treatment days. Additional standard test patterns were used to quantify the leaf position. Results: Whereas the log file reported no difference between planned and recorded positions, image-based measurements showed the leaf to be 1.3±0.1 mm medial from the planned position. This offset was confirmed with the test pattern irradiations. Conclusion: It has been clinically observed that log-file derived leaf positions can differ from their actual positions by >1 mm, and therefore cannot be considered to be the actual leaf positions. This cautions the use of log-based methods for MLC or patient quality assurance without independent confirmation of log integrity. Frequent verification of MLC positions through independent means is a necessary precondition to trusting log file records. Intra-treatment EPID imaging provides a method to capture departures from MLC planned positions. Work was supported in part by Varian Medical Systems.

Review of the Czubek--Jonas gamma-log program

International Nuclear Information System (INIS)

Matthews, M.

1978-11-01

Several gamma-ray logs were computer processed using the Czubek--Jones and DOE's MDDAT gamma-log programs. Both of these programs convert counts per second from the gamma-ray logs to percent eU 3 O 8 . The results of these programs were compared to each other and to the core analysis (percent U 3 O 8 ) of the logged boreholes. The two gamma-log programs produced similar results. The core analysis did not compare favorably with the results of either gamma-log program. This unfavorable comparison is probably due to an incorrect assumption of secular equilibrium for the ore surrounding the boreholes. The Czubek--Jonas program requires a knowledge of the linear attenuation coefficient of the rocks surrounding a borehole. This limits the usefulness of the program because this coefficient is generally not known and varies for different gamma-ray energies. It is recommended that the MDDAT program continue to be used for estimating the grade (percent eU 3 O 8 ) from gamma-log data and not be replaced by the Czubek--Jonas program

CMLOG: A common message logging system

International Nuclear Information System (INIS)

Chen, J.; Akers, W.; Bickley, M.; Wu, D.; Watson, W. III

1997-01-01

The Common Message Logging (CMLOG) system is an object-oriented and distributed system that not only allows applications and systems to log data (messages) of any type into a centralized database but also lets applications view incoming messages in real-time or retrieve stored data from the database according to selection rules. It consists of a concurrent Unix server that handles incoming logging or searching messages, a Motif browser that can view incoming messages in real-time or display stored data in the database, a client daemon that buffers and sends logging messages to the server, and libraries that can be used by applications to send data to or retrieve data from the database via the server. This paper presents the design and implementation of the CMLOG system meanwhile it will also address the issue of integration of CMLOG into existing control systems. CMLOG into existing control systems

Nuclear log interpretation by first principle

International Nuclear Information System (INIS)

Oelgaard, P.L.

1988-07-01

A weakness connected to the present interpretation of nuclear borehole logs is that the interdependence of the various logs and physical effects of importance for the tools are not always taken into account in a correct way. Therefore a new approach to the interpretation of nuclear borehole logs is considered. It is based on the logs obtained with the natural gamma, the neutron porosity, the gamma density, and the pulsed neutron tools. For each of these tools a model, taking into account the important physical effects, is established. These models are incorporated into a computer programme which from the tool signals calculates, by use of iteration, a consistent set of the corresponding formation properties. In the paper the models developed for the four tools and the interpretation programme are briefly described. An example of the use of the interpretation programme is given and compared with a conventional interpretation. (author)

Magnetic Logs from the Lopra-1/1A and Vestmanna-1 wells (Faroe Islands)

DEFF Research Database (Denmark)

Waagstein, R.; Abrahamsen, N.

2006-01-01

basalts poor in magnetite, lapilli-tuffs and tuffs. Thus single measurements of susceptibility are of little use in discriminating between these three types of rock. Susceptibility logs from the Lopra-1/1A  well show that the variation below 3315 m clearly distinguishes between volcaniclastics...... at 2381 m and sidewall cores of basalt from the Lopra-1/1A well have a mean susceptibility of 22.1 ± 3.5 ´ 10-3 SI (σ = 23.6, N = 46), while samples of hyaloclastite (lapilli-tuff and tuff) have a mean susceptibility of 0.85 ´ 10-3 SI (σ = 0.39, N = 17). The mean values of the rock magnetic parameters...

Hydrophysical logging: A new wellbore technology for hydrogeologic and contaminant characterization of aquifers

International Nuclear Information System (INIS)

Pedler, W.H.; Williams, L.L.; Head, C.L.

1992-01-01

In the continuing search for improved groundwater characterization technologies, a new wellbore fluid logging method has recently been developed to provide accurate and cost effective hydrogeologic and contaminant characterization of bedrock aquifers. This new technique, termed hydrophysical logging, provides critical information for contaminated site characterization and water supply studies and, in addition, offers advantages compared to existing industry standards for aquifer characterization. Hydrophysical logging is based on measuring induced electrical conductivity changes in the fluid column of a wellbore by employing advanced downhole water quality instrumentation specifically developed for the dynamic borehole environment. Hydrophysical logging contemporaneously identifies the locations of water bearing intervals, the interval-specific inflow rate during pumping, and in-situ hydrochemistry of the formation waters associated with each producing interval. In addition, by employing a discrete point downhole fluid sampler during hydrophysical logging, this technique provides evaluation of contaminant concentrations and migration of contaminants vertically within the borehole. Recently, hydrophysical logging was applied in a deep bedrock wellbore at an industrial site in New Hampshire contaminated with dense nonaqueous phase liquids (DNAPLs). The results of the hydrophysical logging, conducted as part of a hydrogeologic site investigation and feasibility study, facilitated investigation of the site by providing information which indicated that the contamination had not penetrated into deeper bedrock fractures at concentrations of concern. This information was used to focus the pending Remedial Action Plan and to provide a more cost-effective remedial design

Log evaluation of sub-bituminous coals in Magallanes, Chile

International Nuclear Information System (INIS)

Weltz, L.S.

1976-01-01

In coal exploration a drilling program is normally used for coal inquest through core analysis, with a high cost and operating time. However, in many cases, there is poor cores recovery due to operating procedures and/or formation conditions which leads to the determination of parameters non-representative of the coal seam. The cost and operating time can be minimized through the use of logs which also represent a continuous and in situ sampling. In the case of sub-bituminous coals, the analysis through logs is more complex due to the high content of clay, which masks the presence of water. This paper describes the analysis of sub-bituminous coals in Magallanes-Chile. The main coal seam components are: coal, clay, secondary quartz and water. An interpretation system using the density log, gamma ray, sonic and microlog, based on rho/sub B/-GR and rho/sub B/--Δ/sub T/ cross plots, permits to know the weight percentages of the following elements: total carbon, ash, moisture, which form the main local coal parameters. Empirical relationships permit us to obtain also the heating value and an estimate strength index to elastic-dynamic forces. The results obtained agree within 3 percent with the Laboratory cores analysis. The method is processed through a sequence of simple computer programs for IBM-360

Modeling and Inversion Methods for the Interpretation of Resistivity Logging Tool Response

NARCIS (Netherlands)

Anderson, B.I.

2001-01-01

The electrical resistivity measured by well logging tools is one of the most important rock parameters for indicating the amount of hydrocarbons present in a reservoir. The main interpretation challenge is to invert the measured data, solving for the true resistivity values in each zone of a

Drilling and associated drillhole measurements of the pilot hole ONK-PH12

International Nuclear Information System (INIS)

Toropainen, V.; Tarvainen, A.-M.; Poellaenen, J.; Pekkanen, J.; Pere, T.; Kaepyaho, E.; Lahti, M.

2011-01-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH12 was drilled from ONKALO chainage 4092 to chainage 4215 in January 2010. The length of the hole is 123.96 metres. The drilling method was orientated core drilling. The deviation of the drillhole was measured during and after the drilling phase. Electric conductivity was measured from the collected returning water samples. Logging of the core samples included the following parameters: lithology, foliation, fracturing, fracture frequency, RQD, fractured zones, core loss, and weathering. The rock mechanical logging was based on Q-classification. The test to determine rock strength and deformation were made with Rock Tester -equipment. Water conductivity of the fractures or fractured zones was measured by Posiva Flow Log equipment. The measurements were done in two phases. During flow measurements also grounding resistance electric conductivity and temperature were measured. In flow logging test, sections of 0.5 m with increments of 0.1 m were used. Water loss measurements were conducted in the drillhole section 5.0-123.85 m dhd. Geophysical logging as well as optical and acoustic imaging of the pilot hole included the fieldwork of all surveys, the integration of the data as well as interpretation of the acoustic and drillhole radar data. Groundwater sampling was not applicable because no

Advanced of X-ray fluorescence logging technique in China

International Nuclear Information System (INIS)

Zhou Sichun; Ge Liangquan; Lai Wanchang; Yang Qiang

2010-01-01

The paper discuses principle of X-ray fluorescence logging, and introduces advanced of X-ray fluorescence logging technique in China. By 2009, third generation XRF logging instrument has been developed in China, and good logging result has been obtained in Lala copper mine. (authors)

Nuclear Tools For Oilfield Logging-While-Drilling Applications

International Nuclear Information System (INIS)

Reijonen, Jani

2011-01-01

Schlumberger is an international oilfield service company with nearly 80,000 employees of 140 nationalities, operating globally in 80 countries. As a market leader in oilfield services, Schlumberger has developed a suite of technologies to assess the downhole environment, including, among others, electromagnetic, seismic, chemical, and nuclear measurements. In the past 10 years there has been a radical shift in the oilfield service industry from traditional wireline measurements to logging-while-drilling (LWD) analysis. For LWD measurements, the analysis is performed and the instruments are operated while the borehole is being drilled. The high temperature, high shock, and extreme vibration environment of LWD imposes stringent requirements for the devices used in these applications. This has a significant impact on the design of the components and subcomponents of a downhole tool. Another significant change in the past few years for nuclear-based oilwell logging tools is the desire to replace the sealed radioisotope sources with active, electronic ones. These active radiation sources provide great benefits compared to the isotopic sources, ranging from handling and safety to nonproliferation and well contamination issues. The challenge is to develop electronic generators that have a high degree of reliability for the entire lifetime of a downhole tool. LWD tool testing and operations are highlighted with particular emphasis on electronic radiation sources and nuclear detectors for the downhole environment.

One less trip : logging with less tripping, more protection

Energy Technology Data Exchange (ETDEWEB)

Byfield, M.

2005-12-15

New logging technology by Datalog Technology Inc. was described. Logging-while-tripping (LWT) technology uses a slim petrophysical sensor package that is moved to the targeted geological formation through a drill pipe, which reduces the exposure to vibration and shock involved in logging-while-drilling (LWD). The equipment features standard components in a patented configuration and comes in 2 segments: the receiver sub and the sensor package electronics. A receiver sub is inserted into the bottomhole assembly at the end of the drill string. Drilling progresses with the LWT sub in the bottomhole assembly until the borehole approaches the logging depth. The sensor package and electronics are then lowered into the drill string. If the well is horizontal, rig pumps push the package into the drill string until it lands in the LWT sub. Drill pipes are moved across the zone of interest and logs are recorded on downhole memory contained within the LWT package. As the logging operation progresses, a depth recorder at the surface records depth information along with the downhole recorders. When logging is completed, downhole tools are retrieved, and data downloaded from the LWT onboard memory is merged with the surface depth information to generate well logs. Retrieval via the drill string greatly reduces the risk of losing the logging gear, which contains radioactive material. Federal officials now routinely insist on extensive fishing operations to retrieve lost tools. If a well gets a gas kick while logging is in progress, the operator can still pump down mud or close the blowout preventer rams if necessary, and save time in determining where to perforate shallow gas wells. Compensated neutron logs, gamma rays, spectrum gamma rays, and induction have been tested with the LWT system. It was concluded that Petro-Canada has deployed the logs recently and has achieved results that compared satisfactorily with conventional logs. 2 figs.

Analysis of artificial fireplace logs by high temperature gas chromatography.

Science.gov (United States)

Kuk, Raymond J

2002-11-01

High temperature gas chromatography is used to analyze the wax of artificial fireplace logs (firelogs). Firelogs from several different manufacturers are studied and compared. This study shows that the wax within a single firelog is homogeneous and that the wax is also uniform throughout a multi-firelog package. Different brands are shown to have different wax compositions. Firelogs of the same brand, but purchased in different locations, also have different wax compositions. With this information it may be possible to associate an unknown firelog sample to a known sample, but a definitive statement of the origin cannot be made.

Rill erosion in burned and salvage logged western montane forests: Effects of logging equipment type, traffic level, and slash treatment

Science.gov (United States)

J. W. Wagenbrenner; P. R. Robichaud; R. E. Brown

2016-01-01

Following wildfires, forest managers often consider salvage logging burned trees to recover monetary value of timber, reduce fuel loads, or to meet other objectives. Relatively little is known about the cumulative hydrologic effects of wildfire and subsequent timber harvest using logging equipment. We used controlled rill experiments in logged and unlogged (control)...

Integrated sampling and analysis plan for samples measuring >10 mrem/hour

International Nuclear Information System (INIS)

Haller, C.S.

1992-03-01

This integrated sampling and analysis plan was prepared to assist in planning and scheduling of Hanford Site sampling and analytical activities for all waste characterization samples that measure greater than 10 mrem/hour. This report also satisfies the requirements of the renegotiated Interim Milestone M-10-05 of the Hanford Federal Facility Agreement and Consent Order (the Tri-Party Agreement). For purposes of comparing the various analytical needs with the Hanford Site laboratory capabilities, the analytical requirements of the various programs were normalized by converting required laboratory effort for each type of sample to a common unit of work, the standard analytical equivalency unit (AEU). The AEU approximates the amount of laboratory resources required to perform an extensive suite of analyses on five core segments individually plus one additional suite of analyses on a composite sample derived from a mixture of the five core segments and prepare a validated RCRA-type data package

The nuclear magnetic resonance well logging

International Nuclear Information System (INIS)

Zhang Yumin; Shen Huitang

2003-01-01

In this paper, the characteristic of the nuclear magnetic resonance logging is described at first. Then its development and its principle is presented. Compared with the nuclear magnetic resonance spectrometer, the magnet techniques is the first question that we must solve in the manufacture of the NMR well logging

Combination thermal and radiation shield for well logging apparatus

International Nuclear Information System (INIS)

Wilson, B.F.

1984-01-01

A device for providing both thermal protection and radiation shielding for components such as radiation detectors within a well logging instrument comprises a thermally insulative flask containing a weldment filled with a mass of eutectic material which undergoes a change of state e.g. melting at a temperature which will provide an acceptable thermal environment for such components for extended time periods. The eutectic material which is preferably a bismuth (58%)/tin (42%) alloy has a specific gravity (> 8.5) facilitating its use as a radiation shield and is distributed around the radiation detectors so as to selectively impede the impinging of the detectors by radiation. The device is incorporated in a skid of a well logging instrument for measuring γ backscatter. A γ source is located either above or within the protective shielding. (author)

Measuring radioactive half-lives via statistical sampling in practice

Science.gov (United States)

Lorusso, G.; Collins, S. M.; Jagan, K.; Hitt, G. W.; Sadek, A. M.; Aitken-Smith, P. M.; Bridi, D.; Keightley, J. D.

2017-10-01

The statistical sampling method for the measurement of radioactive decay half-lives exhibits intriguing features such as that the half-life is approximately the median of a distribution closely resembling a Cauchy distribution. Whilst initial theoretical considerations suggested that in certain cases the method could have significant advantages, accurate measurements by statistical sampling have proven difficult, for they require an exercise in non-standard statistical analysis. As a consequence, no half-life measurement using this method has yet been reported and no comparison with traditional methods has ever been made. We used a Monte Carlo approach to address these analysis difficulties, and present the first experimental measurement of a radioisotope half-life (211Pb) by statistical sampling in good agreement with the literature recommended value. Our work also focused on the comparison between statistical sampling and exponential regression analysis, and concluded that exponential regression achieves generally the highest accuracy.

Controlled sliding of logs downhill by chute system integrated with portable winch and synthetic rope

Directory of Open Access Journals (Sweden)

Neşe Gülci

2016-01-01

Full Text Available Over 80% of wood extraction operations have been performed by conventional methods in Turkey. Conventional methods include skidding or sliding of logs mainly by man and animal power, which poses problems in terms of technical, economical, environmental, and ergonomic aspects. Skidding wood on plastic chutes has been implemented in limited numbers of logging applications in recent years, and provides important advantages such as reducing environmental damages and minimizing the value and volume loss of transported wood products. In this study, a chute system integrated with a mobile winch was developed for controlled sliding of large diameter logs downhill. In addition, synthetic ropes rather than steel cables were used to pull log products, resulting in a lower weight and more efficient extraction system. The system was tested on a sample wood production operation in Çınarpınar Forest Enterprise Chief of Kahramanmaraş Forest Enterprise Directorate. In the study, productivity analysis of chute system was performed and its ecological impacts were evaluated. During controlled sliding of logs downhill, the highest productivity (10.01 m3/hour was reached in the fourth chute system characterized as 36 m in length and 70% ground slope. One of the main factors that affected the productivity of chute system was the controlled sliding time of the logs. It was found that residual stand damage was very limited during controlled sliding operations.

Latent log-linear models for handwritten digit classification.

Science.gov (United States)

Deselaers, Thomas; Gass, Tobias; Heigold, Georg; Ney, Hermann

2012-06-01

We present latent log-linear models, an extension of log-linear models incorporating latent variables, and we propose two applications thereof: log-linear mixture models and image deformation-aware log-linear models. The resulting models are fully discriminative, can be trained efficiently, and the model complexity can be controlled. Log-linear mixture models offer additional flexibility within the log-linear modeling framework. Unlike previous approaches, the image deformation-aware model directly considers image deformations and allows for a discriminative training of the deformation parameters. Both are trained using alternating optimization. For certain variants, convergence to a stationary point is guaranteed and, in practice, even variants without this guarantee converge and find models that perform well. We tune the methods on the USPS data set and evaluate on the MNIST data set, demonstrating the generalization capabilities of our proposed models. Our models, although using significantly fewer parameters, are able to obtain competitive results with models proposed in the literature.

Bulk sample self-attenuation correction by transmission measurement

International Nuclear Information System (INIS)

Parker, J.L.; Reilly, T.D.

1976-01-01

Various methods used in either finding or avoiding the attenuation correction in the passive γ-ray assay of bulk samples are reviewed. Detailed consideration is given to the transmission method, which involves experimental determination of the sample linear attenuation coefficient by measuring the transmission through the sample of a beam of gamma rays from an external source. The method was applied to box- and cylindrically-shaped samples

School Principals at Their Lonely Work: Recording Workday Practices through ESM Logs

Science.gov (United States)

Lopez, Veronica; Ahumada, Luis; Galdames, Sergio; Madrid, Romina

2012-01-01

This study used portable technology based on Experience Sampling Methodology (ESM log) to register workday practices of school principals and heads from Chilean schools who were implementing school improvement plans aimed at developing a culture of organizational learning. For a week, Smartphone devices which beeped seven times a day were given to…

Neutron logging reliability techniques and apparatus

International Nuclear Information System (INIS)

Johnstone, C.W.

1978-01-01

This invention relates in general to neutron logging of earth formations, and in particular, to novel apparatus and procedures for determining the validity, or reliability, of data derived at least in part by logging neutron characteristics of earth formations and, if desired, for affording verifiably accurate indications of such data

Neutron logging reliability techniques and apparatus

International Nuclear Information System (INIS)

Johnstone, C.W.

1974-01-01

This invention relates in general to neutron logging of earth formations, and in particular, to novel apparatus and procedures for determining the validity, or reliability, of data derived at least in part by logging neutron characteristics of earth formations and, if desired, for affording verifiably accurate indications of such data. (author)

Low-field NMR logging sensor for measuring hydraulic parameters of model soils

Science.gov (United States)

Sucre, Oscar; Pohlmeier, Andreas; Minière, Adrien; Blümich, Bernhard

2011-08-01

SummaryKnowing the exact hydraulic parameters of soils is very important for improving water management in agriculture and for the refinement of climate models. Up to now, however, the investigation of such parameters has required applying two techniques simultaneously which is time-consuming and invasive. Thus, the objective of this current study is to present only one technique, i.e., a new non-invasive method to measure hydraulic parameters of model soils by using low-field nuclear magnetic resonance (NMR). Hereby, two model clay or sandy soils were respectively filled in a 2 m-long acetate column having an integrated PVC tube. After the soils were completely saturated with water, a low-field NMR sensor was moved up and down in the PVC tube to quantitatively measure along the whole column the initial water content of each soil sample. Thereafter, both columns were allowed to drain. Meanwhile, the NMR sensor was set at a certain depth to measure the water content of that soil slice. Once the hydraulic equilibrium was reached in each of the two columns, a final moisture profile was taken along the whole column. Three curves were subsequently generated accordingly: (1) the initial moisture profile, (2) the evolution curve of the moisture depletion at that particular depth, and (3) the final moisture profile. All three curves were then inverse analyzed using a MATLAB code over numerical data produced with the van Genuchten-Mualem model. Hereby, a set of values ( α, n, θr and θs) was found for the hydraulic parameters for the soils under research. Additionally, the complete decaying NMR signal could be analyzed through Inverse Laplace Transformation and averaged on the 1/ T2 space. Through measurement of the decay in pure water, the effect on the relaxation caused by the sample could be estimated from the obtained spectra. The migration of the sample-related average with decreasing saturation speaks for a enhancement of the surface relaxation as the soil dries, in

Inversion of a lateral log using neural networks

International Nuclear Information System (INIS)

Garcia, G.; Whitman, W.W.

1992-01-01

In this paper a technique using neural networks is demonstrated for the inversion of a lateral log. The lateral log is simulated by a finite difference method which in turn is used as an input to a backpropagation neural network. An initial guess earth model is generated from the neural network, which is then input to a Marquardt inversion. The neural network reacts to gross and subtle data features in actual logs and produces a response inferred from the knowledge stored in the network during a training process. The neural network inversion of lateral logs is tested on synthetic and field data. Tests using field data resulted in a final earth model whose simulated lateral is in good agreement with the actual log data

log gf values for astrophysically important transitions Fe II

Science.gov (United States)

Deb, N. C.; Hibbert, A.

2014-01-01

Aims: In a recent measurement, Meléndez & Barbuy (2009, A&A, 497, 611) report accurate log gf values for 142 important astrophysical lines with wavelengths in the range 4000 Å to 8000 Å. Their results include both solar and laboratory measurements. In this paper, we describe a theoretical study of these lines. Methods: The CIV3 structure codes, combined with our "fine-tuning" extrapolation process, are used to undertake a large-scale CI calculation involving the lowest 262 fine-structure levels belonging to the 3d64s, 3d7, 3d54s2, 3d64p, and 3d54s4p configurations. Results: We find that many of the 142 transitions are very weak intercombination lines. Other transitions are weak because the dominant configurations in the two levels differ by two orbitals. Conclusions: The comparison between our log gf values and the experimental values generally shows good agreement for most of these transitions, with our theoretical values agreeing slightly more closely with the solar than with the laboratory measurements. A detailed analysis of the small number of transitions for which the agreement between theory and experiment is not as good shows that such disagreements largely arise from severe cancellation due to CI mixing.

Assessment of the Water and Sediment Quality of Tropical Forest Streams in Upper Reaches of the Baleh River, Sarawak, Malaysia, Subjected to Logging Activities

Directory of Open Access Journals (Sweden)

Teck-Yee Ling

2016-01-01

Full Text Available The study of the impact of logging activities on water and sediment quality of Sarawak forest streams is still scarce despite Sarawak being the largest exporter of timber in Malaysia. This study was aimed at determining the water and sediment quality of forest streams in Sarawak and the potential impact of logging activities. In situ parameters were measured, and water and sediment samples were collected at six stations before rain. Additionally, water quality was investigated at three stations after rain. The results showed that canopy removal resulted in large temperature variation and sedimentation in the forest streams. Lower suspended solids were found at stations with inactive logging (<2 mg/L compared to active logging (10–16 mg/L activities. The highest concentration of total nitrogen and total phosphorus in water and sediment was 4.4 mg/L, 77.6 μg/L, 0.17%, and 0.01%, respectively. Besides, significantly negative correlation of sediment nitrogen and water total ammonia nitrogen indicated the loss of nitrogen from sediment to water. Water quality of the streams deteriorated after rain, in particular, suspended solids which increased from 8.3 mg/L to 104.1 mg/L. This study reveals that logging activities have an impact on the water quality of Sarawak forest streams particularly in rainfall events.

Carbon emissions performance of commercial logging in East Kalimantan, Indonesia.

Science.gov (United States)

Griscom, Bronson; Ellis, Peter; Putz, Francis E

2014-03-01

Adoption of reduced-impact logging (RIL) methods could reduce CO2 emissions by 30-50% across at least 20% of remaining tropical forests. We developed two cost effective and robust indices for comparing the climate benefits (reduced CO2 emissions) due to RIL. The indices correct for variability in the volume of commercial timber among concessions. We determined that a correction for variability in terrain slope was not needed. We found that concessions certified by the Forest Stewardship Council (FSC, N = 3), when compared with noncertified concessions (N = 6), did not have lower overall CO2 emissions from logging activity (felling, skidding, and hauling). On the other hand, FSC certified concessions did have lower emissions from one type of logging impact (skidding), and we found evidence of a range of improved practices using other field metrics. One explanation of these results may be that FSC criteria and indicators, and associated RIL practices, were not designed to achieve overall emissions reductions. Also, commonly used field metrics are not reliable proxies for overall logging emissions performance. Furthermore, the simple distinction between certified and noncertified concessions does not fully represent the complex history of investments in improved logging practices. To clarify the relationship between RIL and emissions reductions, we propose the more explicit term 'RIL-C' to refer to the subset of RIL practices that can be defined by quantified thresholds and that result in measurable emissions reductions. If tropical forest certification is to be linked with CO2 emissions reductions, certification standards need to explicitly require RIL-C practices. © 2013 John Wiley & Sons Ltd.

Ordinal Log-Linear Models for Contingency Tables

Directory of Open Access Journals (Sweden)

Brzezińska Justyna

2016-12-01

Full Text Available A log-linear analysis is a method providing a comprehensive scheme to describe the association for categorical variables in a contingency table. The log-linear model specifies how the expected counts depend on the levels of the categorical variables for these cells and provide detailed information on the associations. The aim of this paper is to present theoretical, as well as empirical, aspects of ordinal log-linear models used for contingency tables with ordinal variables. We introduce log-linear models for ordinal variables: linear-by-linear association, row effect model, column effect model and RC Goodman’s model. Algorithm, advantages and disadvantages will be discussed in the paper. An empirical analysis will be conducted with the use of R.

Drilling and the associated drillhole measurements of the pilot hole ONK-PH6

International Nuclear Information System (INIS)

Oehberg, A.; Hirvonen, H.; Kemppainen, K.; Niemonen, J.; Nordbaeck, N.; Poellaenen, J.; Rouhiainen, P.; Rautio, T.; Tarvainen, A.-M.

2007-08-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH6 was drilled from chainage 1404 to chainage 1559 in September 2006. The length of the hole is 155.04 m. The aim during the drilling work was to orient core samples as much as possible. The deviation of the drillhole was measured during and after the drilling phase. One steering operation by wedging was made at the hole depth of 94.05 metres (top of the wedge). Electric conductivity was measured from the collected returning water samples. Logging of the core samples included the following parameters: lithology, foliation, fracturing, fracture frequency, RQD, fractured zones, core loss and weathering. The rock mechanical logging was based on Q-classification. The tests to determine rock strength and deformation properties were made with a Rock Tester-equipment. Difference Flow method was used for the determination of hydraulic conductivity in fractures and fractured zones in the drillhole. The overlapping i.e. the detailed flow logging mode was used. Besides flow logging Single Point Resistance (SPR), Electric Conductivity (EC) and temperature of the drillhole water were also measured. The flow logging was performed with 0.5 m section length and with 0.1 m depth increment. Water loss tests were conducted in the hole excluding the section 89.04 - 101.04 metres due to the wedge. Geophysical logging

Investigated conductive fracture in the granitic rocks by flow-meter logging

International Nuclear Information System (INIS)

Ogata, Nobuhisa; Koide, Kaoru; Takeichi, Atsushi

1997-01-01

Test of the use of a measurement technique for the hydraulic conductivity of geological structures which act as flow paths or are impermeable to groundwater flow. In order to prove the value of flow-meter logging as an in-situ technique for detecting conductive fractures in granitic rocks, the method has been applied to a borehole near the Tono uranium mine, Gifu, Japan. This study in involved with detecting a conductive fracture and calculating the hydraulic conductivities. The results were as follows: (1) In a zone of groundwater inflow into the borehole, the hydraulic conductivity was calculated to be of the order of the 10 -3 - 10 -4 (cm/sec) from flow-meter logging. This value agreed with the results of a in-situ borehole permeability test carried out with a similar depth interval. (2) The study showed that flow-meter logging is effective for detecting the distribution of high conductivity fractures and calculating the hydraulic conductivity. (author)

Hydrocarbon type identification with MWD neutron porosity logging

International Nuclear Information System (INIS)

Simms, G.J.; Koopersmith, C.A.

1991-01-01

This paper reports on measurement-while-drilling (MWD) information which accurately defined gas, oil, and water in an offshore field. Basic MWD and wireline formation evaluation data compare favorably. A cost saving of $120,000 was realized when MWD information was used instead of wireline data on one well. In the future, MWD logs may serve as the primary evaluation data on routine development wells in similar fields

Data Cleaning Methods for Client and Proxy Logs

NARCIS (Netherlands)

Weinreich, H.; Obendorf, H.; Herder, E.; Edmonds, A.; Hawkey, K.; Kellar, M.; Turnbull, D.

2006-01-01

In this paper we present our experiences with the cleaning of Web client and proxy usage logs, based on a long-term browsing study with 25 participants. A detailed clickstream log, recorded using a Web intermediary, was combined with a second log of user interface actions, which was captured by a

Financial and Economic Analysis of Reduced Impact Logging

Science.gov (United States)

Tom Holmes

2016-01-01

Concern regarding extensive damage to tropical forests resulting from logging increased dramatically after World War II when mechanized logging systems developed in industrialized countries were deployed in the tropics. As a consequence, tropical foresters began developing logging procedures that were more environmentally benign, and by the 1990s, these practices began...

Using Web Server Logs in Evaluating Instructional Web Sites.

Science.gov (United States)

Ingram, Albert L.

2000-01-01

Web server logs contain a great deal of information about who uses a Web site and how they use it. This article discusses the analysis of Web logs for instructional Web sites; reviews the data stored in most Web server logs; demonstrates what further information can be gleaned from the logs; and discusses analyzing that information for the…

Integrating sphere based reflectance measurements for small-area semiconductor samples

Science.gov (United States)

Saylan, S.; Howells, C. T.; Dahlem, M. S.

2018-05-01

This article describes a method that enables reflectance spectroscopy of small semiconductor samples using an integrating sphere, without the use of additional optical elements. We employed an inexpensive sample holder to measure the reflectance of different samples through 2-, 3-, and 4.5-mm-diameter apertures and applied a mathematical formulation to remove the bias from the measured spectra caused by illumination of the holder. Using the proposed method, the reflectance of samples fabricated using expensive or rare materials and/or low-throughput processes can be measured. It can also be incorporated to infer the internal quantum efficiency of small-area, research-level solar cells. Moreover, small samples that reflect light at large angles and develop scattering may also be measured reliably, by virtue of an integrating sphere insensitive to directionalities.

Tucker Wireline Open Hole Wireline Logging; FINAL

International Nuclear Information System (INIS)

Milliken, M.

2002-01-01

The Tucker Wireline unit ran a suite of open hole logs right behind the RMOTC logging contractor for comparison purposes. The tools included Dual Laterolog, Phased Induction, BHC Sonic, and Density-Porosity

Landscape-scale changes in forest canopy structure across a partially logged tropical peat swamp

Science.gov (United States)

Wedeux, B. M. M.; Coomes, D. A.

2015-11-01

Forest canopy structure is strongly influenced by environmental factors and disturbance, and in turn influences key ecosystem processes including productivity, evapotranspiration and habitat availability. In tropical forests increasingly modified by human activities, the interplay between environmental factors and disturbance legacies on forest canopy structure across landscapes is practically unexplored. We used airborne laser scanning (ALS) data to measure the canopy of old-growth and selectively logged peat swamp forest across a peat dome in Central Kalimantan, Indonesia, and quantified how canopy structure metrics varied with peat depth and under logging. Several million canopy gaps in different height cross-sections of the canopy were measured in 100 plots of 1 km2 spanning the peat dome, allowing us to describe canopy structure with seven metrics. Old-growth forest became shorter and had simpler vertical canopy profiles on deeper peat, consistent with previous work linking deep peat to stunted tree growth. Gap size frequency distributions (GSFDs) indicated fewer and smaller canopy gaps on the deeper peat (i.e. the scaling exponent of Pareto functions increased from 1.76 to 3.76 with peat depth). Areas subjected to concessionary logging until 2000, and illegal logging since then, had the same canopy top height as old-growth forest, indicating the persistence of some large trees, but mean canopy height was significantly reduced. With logging, the total area of canopy gaps increased and the GSFD scaling exponent was reduced. Logging effects were most evident on the deepest peat, where nutrient depletion and waterlogged conditions restrain tree growth and recovery. A tight relationship exists between canopy structure and peat depth gradient within the old-growth tropical peat swamp forest. This relationship breaks down after selective logging, with canopy structural recovery, as observed by ALS, modulated by environmental conditions. These findings improve our

A Lower Bound on the Differential Entropy of Log-Concave Random Vectors with Applications

Directory of Open Access Journals (Sweden)

Arnaud Marsiglietti

2018-03-01

Full Text Available We derive a lower bound on the differential entropy of a log-concave random variable X in terms of the p-th absolute moment of X. The new bound leads to a reverse entropy power inequality with an explicit constant, and to new bounds on the rate-distortion function and the channel capacity. Specifically, we study the rate-distortion function for log-concave sources and distortion measure d ( x , x ^ = | x − x ^ | r , with r ≥ 1 , and we establish that the difference between the rate-distortion function and the Shannon lower bound is at most log ( π e ≈ 1 . 5 bits, independently of r and the target distortion d. For mean-square error distortion, the difference is at most log ( π e 2 ≈ 1 bit, regardless of d. We also provide bounds on the capacity of memoryless additive noise channels when the noise is log-concave. We show that the difference between the capacity of such channels and the capacity of the Gaussian channel with the same noise power is at most log ( π e 2 ≈ 1 bit. Our results generalize to the case of a random vector X with possibly dependent coordinates. Our proof technique leverages tools from convex geometry.

Producing Hardwood Dimension Parts Directly From Logs: An Economic Feasibility Study

Science.gov (United States)

Wenjie Lin; D. Earl Kline; Philip A. Araman; Janice K. Wiedenbeck

1995-01-01

The economic feasibility and profitability of a direct processing system for converting Factory Grades 2 and 3 red oak logs directly into rough dimension parts were evaluated. New present value (NPV) and internal rate of return (IRR) were used as the measurement of economic feasibility, and return on sales (ROS) was used as the measurement of profitability. NPV and IRR...

Analyzing engagement in a web-based intervention platform through visualizing log-data.

Science.gov (United States)

Morrison, Cecily; Doherty, Gavin

2014-11-13

Engagement has emerged as a significant cross-cutting concern within the development of Web-based interventions. There have been calls to institute a more rigorous approach to the design of Web-based interventions, to increase both the quantity and quality of engagement. One approach would be to use log-data to better understand the process of engagement and patterns of use. However, an important challenge lies in organizing log-data for productive analysis. Our aim was to conduct an initial exploration of the use of visualizations of log-data to enhance understanding of engagement with Web-based interventions. We applied exploratory sequential data analysis to highlight sequential aspects of the log data, such as time or module number, to provide insights into engagement. After applying a number of processing steps, a range of visualizations were generated from the log-data. We then examined the usefulness of these visualizations for understanding the engagement of individual users and the engagement of cohorts of users. The visualizations created are illustrated with two datasets drawn from studies using the SilverCloud Platform: (1) a small, detailed dataset with interviews (n=19) and (2) a large dataset (n=326) with 44,838 logged events. We present four exploratory visualizations of user engagement with a Web-based intervention, including Navigation Graph, Stripe Graph, Start-Finish Graph, and Next Action Heat Map. The first represents individual usage and the last three, specific aspects of cohort usage. We provide examples of each with a discussion of salient features. Log-data analysis through data visualization is an alternative way of exploring user engagement with Web-based interventions, which can yield different insights than more commonly used summative measures. We describe how understanding the process of engagement through visualizations can support the development and evaluation of Web-based interventions. Specifically, we show how visualizations

Sampling Criterion for EMC Near Field Measurements

DEFF Research Database (Denmark)

Franek, Ondrej; Sørensen, Morten; Ebert, Hans

2012-01-01

An alternative, quasi-empirical sampling criterion for EMC near field measurements intended for close coupling investigations is proposed. The criterion is based on maximum error caused by sub-optimal sampling of near fields in the vicinity of an elementary dipole, which is suggested as a worst......-case representative of a signal trace on a typical printed circuit board. It has been found that the sampling density derived in this way is in fact very similar to that given by the antenna near field sampling theorem, if an error less than 1 dB is required. The principal advantage of the proposed formulation is its...

Measurement of trace elements in liver biopsy samples from cattle

NARCIS (Netherlands)

Ouweltjes, W.; Zeeuw, de A.C.; Moen, A.; Counotte, G.H.M.

2007-01-01

Serum, plasma, or urine samples are usually used for the measurement of the trace elements copper, zinc, iron, selenium, because these samples are easy to obtain; however, these samples are not always appropriate. For example, it is not possible to measure molybdenum, the major antagonist of copper,

High-resolution well-log derived dielectric properties of gas-hydrate-bearing sediments, Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

Science.gov (United States)

Sun, Y.; Goldberg, D.; Collett, T.; Hunter, R.

2011-01-01

A dielectric logging tool, electromagnetic propagation tool (EPT), was deployed in 2007 in the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well (Mount Elbert Well), North Slope, Alaska. The measured dielectric properties in the Mount Elbert well, combined with density log measurements, result in a vertical high-resolution (cm-scale) estimate of gas hydrate saturation. Two hydrate-bearing sand reservoirs about 20 m thick were identified using the EPT log and exhibited gas-hydrate saturation estimates ranging from 45% to 85%. In hydrate-bearing zones where variation of hole size and oil-based mud invasion are minimal, EPT-based gas hydrate saturation estimates on average agree well with lower vertical resolution estimates from the nuclear magnetic resonance logs; however, saturation and porosity estimates based on EPT logs are not reliable in intervals with substantial variations in borehole diameter and oil-based invasion.EPT log interpretation reveals many thin-bedded layers at various depths, both above and below the thick continuous hydrate occurrences, which range from 30-cm to about 1-m thick. Such thin layers are not indicated in other well logs, or from the visual observation of core, with the exception of the image log recorded by the oil-base microimager. We also observe that EPT dielectric measurements can be used to accurately detect fine-scale changes in lithology and pore fluid properties of hydrate-bearing sediments where variation of hole size is minimal. EPT measurements may thus provide high-resolution in-situ hydrate saturation estimates for comparison and calibration with laboratory analysis. ?? 2010 Elsevier Ltd.

Features of the electric discharge logging system; Hoden hoshiki jiban tansa system no tokucho

Energy Technology Data Exchange (ETDEWEB)

Kudo, K; Yasuda, N [Tokyo Electric Power Co. Inc., Tokyo (Japan); Kuniyasu, T; Kanda, K; Tanaka, T

1997-10-22

Logging system has been developed, which performs discharge in the water in a bore hole relatively small in diameter. The part of this system to operate in the hole consists of an oscillator that triggers off discharge in the water and an oscillation receiving set that utilizes electrostriction proper to ceramics. The groundborne part of the system is comprised of a probe lift control and logging control. The logging process is carried out by causing discharge in the water in a bore hole filled with water. The energy generated by the oscillator is far greater than that produced in the sonic logging or suspension type logging method, and the wave generated and propagated in the hole is received by the receiving set in the same hole. The result indicates that the P-wave velocity in a hard rockbed is rather high and that values obtained on the spot by this system is quite similar to those obtained from the core sample from the hole. In the case of a rock bed abundant in cracks, thanks to the high S/N ratio such a bed presents and the merits of digital recording, investigations can be minutely conducted. The merit of this system is found in that it can damp the amplitude in dealing with the data collected on the spot. 3 refs., 7 figs.

Measurement assurance program for LSC analyses of tritium samples

International Nuclear Information System (INIS)

Levi, G.D. Jr.; Clark, J.P.

1997-01-01

Liquid Scintillation Counting (LSC) for Tritium is done on 600 to 800 samples daily as part of a contamination control program at the Savannah River Site's Tritium Facilities. The tritium results from the LSCs are used: to release items as radiologically clean; to establish radiological control measures for workers; and to characterize waste. The following is a list of the sample matrices that are analyzed for tritium: filter paper smears, aqueous, oil, oily rags, ethylene glycol, ethyl alcohol, freon and mercury. Routine and special causes of variation in standards, counting equipment, environment, operators, counting times, samples, activity levels, etc. produce uncertainty in the LSC measurements. A comprehensive analytical process measurement assurance program such as JTIPMAP trademark has been implemented. The process measurement assurance program is being used to quantify and control many of the sources of variation and provide accurate estimates of the overall measurement uncertainty associated with the LSC measurements. The paper will describe LSC operations, process improvements, quality control and quality assurance programs along with future improvements associated with the implementation of the process measurement assurance program

Neutron--neutron logging

International Nuclear Information System (INIS)

Allen, L.S.

1977-01-01

A borehole logging tool includes a steady-state source of fast neutrons, two epithermal neutron detectors, and two thermal neutron detectors. A count rate meter is connected to each neutron detector. A first ratio detector provides an indication of the porosity of the formation surrounding the borehole by determining the ratio of the outputs of the two count rate meters connected to the two epithermal neutron detectors. A second ratio detector provides an indication of both porosity and macroscopic absorption cross section of the formation surrounding the borehole by determining the ratio of the outputs of the two count rate meters connected to the two thermal neutron detectors. By comparing the signals of the two ratio detectors, oil bearing zones and salt water bearing zones within the formation being logged can be distinguished and the amount of oil saturation can be determined. 6 claims, 2 figures

Learning analytics in serious gaming: uncovering the hidden treasury of game log files

NARCIS (Netherlands)

Westera, Wim; Nadolski, Rob; Hummel, Hans

2018-01-01

This paper presents an exploratory analysis of existing log files of the VIBOA environmental policy games at Utrecht University. For reasons of statistical power we’ve combined student cohorts 2008, 2009, 2010, and 2011, which led to a sample size of 118 students. The VIBOA games are inquiry-based

Synthetic rope applications in Appalachian logging

Science.gov (United States)

Ben D. Spong; Jingxin Wang

2008-01-01

New ultra-high molecular weight polyethylene rope has shown good results as a replacement for wire rope in logging applications in the western United States. A single case study trial was performed in Appalachian forest conditions to assess the appropriateness of this technology for hardwood logging applications. The study focused on use of the rope in West Virginia...

A survey of animal-powered logging in Alabama

Science.gov (United States)

Christopher W. Toms; Mark R. Dubois; John C. Bliss; John H. Wilhoit; Robert B. Rummer

2001-01-01

In a state with a very large, highly mechanized timber harvesting industry, animal-powered logging still occupies a niche in Alabama as a small-scale harvesting alternative. This article summarizes the results from a study that examined the extent of animal logging in Alabama. We investigated this topic by asking who is logging with animals, where are they working,...

Sediment transport and soil disturbance after postfire logging.

Science.gov (United States)

James D. McIver

2003-01-01

Recently there has been considerable debate on the practice of postfire logging, in which burned forests are entered soon after fire to recover commercially valuable trees. Proponents of the practice argue that postfire logging is part of a 'restoration package' that can be used to control erosion (e.g., contour logging) and can help to mitigate costs of...

Use of pulsed neutron-neutron logging, thermal neutron-neutron logging, and gamma logging methods in classification for sand-clay sediments of Lower Cretaceous in Prikumsk oil-and-gas region according to filtration-capacitance characteristics

International Nuclear Information System (INIS)

Maksimenko, A.N.; Basin, Ya.N.; Novgorodov, V.A.

1974-01-01

To isolate reservoirs, the formation and deformation penetration zone parameters are used. They are estimated according to the false oil saturation factor and the time of the penetration zone deformation which are determined from the complex exploration of cased wells using the pulse neutron logging, thermal neutron-neutron logging and gamma logging techniques

Application of gamma-gamma logging in predicting anomalous geodynamic phenomena in hard coal mines

International Nuclear Information System (INIS)

Blaha, F.; Keclik, L.

1980-01-01

The application is discussed of gamma-gamma logging in the prediction of dynamic events like coal and gas bursts, coal sliding in medium dip seams and rock bumps. The overall analysis of the applied rock characterization method and of the measurement results shows that the prediction possibilities of dynamic events are partly limited due to specific effects of the rock massive. In these cases, however, unambiguous results may be obtained by other geophysical methods such as seismoacoustic testing etc. In most cases, however, the gamma-gamma logging results may be used for estimating the degree of dynamic events or checking the efficiency of preventive measures in the locality under investigation. (author)

The Influence of Log Felling Season on the Extent of Discoloration in Rubberwood Sawn Timber during the Kiln Drying Process

Directory of Open Access Journals (Sweden)

Jegatheswaran Ratnasingam

2016-04-01

Full Text Available This study investigated the effects of felling season on the discoloration of rubberwood sawn timber during conventional kiln drying. The samples were collected throughout the year 2015 to monitor the variation of free sugars and starch content in the rubberwood logs. Two batches of logs, one from the rainy season and the other from the dry season, were felled and sawn for experimentation. The findings showed that discoloration was more prominent in sawn timber obtained from logs felled during the dry season. The amount of free sugars and starch in the logs had a strong influence on the extent of discoloration in the rubberwood sawn timber during the kiln drying process. A higher amount of free sugars and starch in the logs felled during the dry season increased the incidence of blue stain on these logs. The results of this study conclusively showed that discoloration in rubberwood can be minimized by the choice of log felling season and the use of an appropriate drying technique, which will inevitably improve the aesthetic appeal of the wood.

Interval sampling methods and measurement error: a computer simulation.

Science.gov (United States)

Wirth, Oliver; Slaven, James; Taylor, Matthew A

2014-01-01

A simulation study was conducted to provide a more thorough account of measurement error associated with interval sampling methods. A computer program simulated the application of momentary time sampling, partial-interval recording, and whole-interval recording methods on target events randomly distributed across an observation period. The simulation yielded measures of error for multiple combinations of observation period, interval duration, event duration, and cumulative event duration. The simulations were conducted up to 100 times to yield measures of error variability. Although the present simulation confirmed some previously reported characteristics of interval sampling methods, it also revealed many new findings that pertain to each method's inherent strengths and weaknesses. The analysis and resulting error tables can help guide the selection of the most appropriate sampling method for observation-based behavioral assessments. © Society for the Experimental Analysis of Behavior.

Supply of Rubber Wood Log in Malaysia

OpenAIRE

Noraida, A. W.; Abdul-Rahim, A. S.

2014-01-01

Issue on shortage of raw material for wood processing solved by discovery of rubber wood log as one of the substitutes the natural log. This paper examines the supply of rubber wood log in Malaysia. We employ ARDL Bound Approach Test and time series data from 1980 to 2010 which represented the whole Malaysia are used to achieve the established objectives. The result shown, in the long run harvested area and wages have 1% and 10% significant level respectively. While in the short run, there wa...

From Log Files to Assessment Metrics: Measuring Students' Science Inquiry Skills Using Educational Data Mining

Science.gov (United States)

Gobert, Janice D.; Sao Pedro, Michael; Raziuddin, Juelaila; Baker, Ryan S.

2013-01-01

We present a method for assessing science inquiry performance, specifically for the inquiry skill of designing and conducting experiments, using educational data mining on students' log data from online microworlds in the Inq-ITS system (Inquiry Intelligent Tutoring System; www.inq-its.org). In our approach, we use a 2-step process: First we use…

POPULATION STRUCTURES OF FOUR TREE SPECIES IN LOGGED-OVER TROPICAL FOREST IN SOUTH PAPUA, INDONESIA: AN INTEGRAL PROJECTION MODEL APPROACH

Directory of Open Access Journals (Sweden)

Relawan kuswandi

2015-12-01

Full Text Available Selective logging has been taking place in Papua for several decades. In contrast, very little is known about the stand structure in post-logged forest. Hence, this paper investigates stand structures in logged-over area of tropical forest in South Papua. Four species were selected in three one-hectare permanent sample plots (PSPs: Vatica rassak, Syzygium sp, Litsea timoriana and Canarium asperum. PSPs were located in the forest concession area of PT. Tunas Sawaerma in Assiki, Boven Digul, in South Papua. Data sets comprised measurements made in 2005 and 2012 consisting of species, diameter at breast height (DBH, mortality and number of tree of each species. Integral Projection Models (IPMs were developed, taking into account mortality, growth, recruitment and fecundity. Results show the pattern of stand structures of the four species were more or less similar, i.e. more individual trees were present in the small diameter classes than in the larger diameter classes. The general pattern of the individual distribution of the four species is the typical reverse-J shape. Syzygium sp. has a greater number of individuals in the small diameter classes than the other three species. Population growth rates (λ are above one, indicating that the stand structures of the population dynamics of the four species are recuperating. Conclusively, these results suggest that species composition and population structure in these logged-over forests are recovering increasingly.

Acoustic--nuclear permeability logging system

International Nuclear Information System (INIS)

Dowling, D.J.; Arnold, D.M.

1978-01-01

A down hole logging tool featuring a neutron generator, an acoustic disturbance generator, and a radiation detection system is described. An array of acoustic magnetostriction transducers is arranged about the target of a neutron accelerator. Two gamma ray sensors are separated from the accelerator target by shielding. According to the method of the invention, the underground fluid at the level of a formation is bombarded by neutrons which react with oxygen in the fluid to produce unstable nitrogen 16 particles according to the reaction 16 O(n,p) 16 N. Acoustic pulses are communicated to the fluid, and are incident on the boundary of the borehole at the formation. The resulting net flow of fluid across the boundary is determined from radiation detection measurements of the decaying 16 N particles in the fluid. A measure of the permeability of the formation is obtained from the determination of net fluid flow across the boundary

Well logging, atom and geology

International Nuclear Information System (INIS)

Serra, O.

1994-01-01

Well logging techniques exploit interactions of gamma photons and neutrons with atoms. Interactions of neutrons of different energies with atoms allow the detection and evaluation of the weight percentage of several elements composing the rocks (C, O, Si, Ca, Fe, S); spectrometry of gamma rays produced by thermal neutron absorption allows for the weight percentage determination of Si, Ca, Fe, S, Cl, H, Ti and Gd, etc. High resolution detectors (germanium doped by Li, at liquid nitrogen temperature) allow the recognition of more elements. Other techniques involving neutrons consist in determining the population in epithermal neutrons at a certain distance of the neutron source (measurement of the hydrogen index). By analyzing the intensity of the gamma flux produced by Compton scattering, the electronic and bulk densities of the rocks are measured. All these data lead to the detection and evaluation of ore deposits (uranium and potassium) and coal, and determination of the lithology, the main minerals composing the rocks, petrophysical properties... 1 fig

National logging program for the National Uranium Resource Evaluation. Final report

International Nuclear Information System (INIS)

The Mineral Engineering Division (MED) of High Life Helicopters, Inc., operated from May, 1979, through August, 1981, as a subcontractor to the Department of Energy (DOE) to acquire downhole geophysical log information in support of the National Uranium Resource Evaluation program (NURE). MED acquired downhole geophysical log information in 26 1 0 x 2 0 NTMS quadrangles in Colorado, Montana, Nebraska, North Dakota, South Dakota, and Wyoming. MED obtained the log information by gaining permission to log oil and gas wells, water wells, and coal exploration holes. Actual geophysical logging was subcontracted to Century Geophysical Corporation. After logging of each well and completed, MED submitted the log information and other pertinent data to Bendix Field Engineering Corporation (BFEC) for evaluation. MED collected over 700,000 feet of geophysical logs. Additionally, MED conducted a search of log libraries for existing log data for twelve of the quadrangles included in the program. It should be noted that ERTEC, Inc. conducted geophysical logging and a log library search to five quadrangles in Wyoming. These areas were later assigned to MED. The location of all wells logged by MED and ERTEC and the location of other log data is shown on the enclosed maps. Detailed information that pertains to each well is provided following each map

Calibration of a neutron log in partially saturated media. Part II. Error analysis

International Nuclear Information System (INIS)

Hearst, J.R.; Kasameyer, P.W.; Dreiling, L.A.

1981-01-01

Four sources or error (uncertainty) are studied in water content obtained from neutron logs calibrated in partially saturated media for holes up to 3 m. For this calibration a special facility was built and an algorithm for a commercial epithermal neutron log was developed that obtains water content from count rate, bulk density, and gap between the neutron sonde and the borehole wall. The algorithm contained errors due to the calibration and lack of fit, while the field measurements included uncertainties in the count rate (caused by statistics and a short time constant), gap, and density. There can be inhomogeneity in the material surrounding the borehole. Under normal field conditions the hole-size-corrected water content obtained from such neutron logs can have an uncertainty as large as 15% of its value

Porosity measurements of crystalline rocks by laboratory and geophysical methods

International Nuclear Information System (INIS)

Alexander, J.; Hall, D.H.; Storey, B.C.

1981-12-01

Porosity values of igneous and metamorphic crystalline rocks have been determined from core samples taken at specific depths from Altnabreac, by a combination of laboratory and geophysical techniques. Using resaturation and mercury injection methods in three laboratories within I.G.S., porosity values have been derived and the effect of variations in the measuring techniques and results obtained have been compared. Comparison of inter-laboratory porosity values illustrates that systematic errors are present, resulting in higher porosity values for samples subjected to re-testing. This is considered to be caused by the variable nature of the initial samples combined with the inability to completely dry or resaturate samples during a second testing. Geophysical techniques for determining in situ porosity using the neutron log have been carried out in borehole ALA. The neutron log has been calibrated with laboratory derived porosity values and an empirical formula derived enabling porosity values to be ascribed throughout the logged borehole ALA. Comparison of the porosity results from Altnabreac with crystalline samples elsewhere in America, Europe and the U.K. suggest that porosities at Altnabreac are lower than average. However, very few publications concerned with water movement in crystalline areas actually state the method used. (author)

Identification and characterization of the active hydrothermal deposits in Okinawa Trough, SW Japan: Estimates from logging-while-drilling

Science.gov (United States)

Saito, S.; Sanada, Y.; Moe, K.; Kido, Y. N.; Hamada, Y.; Kumagai, H.; Nozaki, T.; Takai, K.; Suzuki, K.

2015-12-01

A scientific drilling expedition was conducted at an active hydrothermal field on the Iheya-North Knoll by D/V Chikyu in 2014 (Expedition 907) as a part of "Next-generation Technology for Ocean Resources Survey" of the Cross-ministerial Strategic Innovation Promotion Program. During the expedition logging while drilling (LWD) was deployed to constrain the area of the fluid reservoir beneath seafloor followed by three coring holes down to 150 meter below the seafloor (mbsf). The LWD system is composed of arcVISION for resistivity and natural gamma ray measurement and TeleScope for real-time transmission of drilling parameters and arcVISION data. Five sites (C9011-15) at the Iheya-North Original Site and one site (C9016) at Aki Site were drilled with LWD. At C9012 and C9016, the arcVISION detected temperature anomaly up to 84℃ at 234 mbsf and up to 39℃ at 80 mbsf, respectively. The temperature quickly increases at that depth and it would reflect the existence of high-temperature heat source along borehole. Due to the continuous fluid circulation during drilling, the measured temperature does not indicate in-situ temperature, but it reflects the heat disturbed by the cold circulated water instead. High quality resistivity and natural gamma ray data were acquired at six sites. The log curves at Site C9016 show characteristic response; the natural gamma ray log exhibits extremely high radiation (>500 gAPI) at 7-13 and 23-31 mbsf (Zone A). In the underlying interval of 31-40 mbsf, the resistivity log exhibits extremely low value (LWD-based lithological interpretation was confirmed by the following core description. Zones A and B can be correlated to altered clay zone and sulfide zone including sphalerite, galena, chalcopyrite, and pyrite. Our results show that LWD is a powerful tool for the identification and characterization of submarine hydrothermal deposits and LWD survey enhances the successful recovery of sulfide samples.

Nonblocking and orphan free message logging protocols

Science.gov (United States)

Alvisi, Lorenzo; Hoppe, Bruce; Marzullo, Keith

1992-12-01

Currently existing message logging protocols demonstrate a classic pessimistic vs. optimistic tradeoff. We show that the optimistic-pessimistic tradeoff is not inherent to the problem of message logging. We construct a message-logging protocol that has the positive features of both optimistic and pessimistic protocol: our protocol prevents orphans and allows simple failure recovery; however, it requires no blocking in failure-free runs. Furthermore, this protocol does not introduce any additional message overhead as compared to one implemented for a system in which messages may be lost but processes do not crash.

Logging methods and peeling of Aspen