Politics and technology in repository siting: military versus commercial nuclear wastes at WIPP 1972-1985

International Nuclear Information System (INIS)

Downey, G.L.

1985-01-01

During the 1970s, attempts by the federal government to develop a comprehensive system for disposing of nuclear wastes in geologic repositories were plagued by two related political problems; (1) whether or not military and commercial wastes should be buried together in the same repository, and (2) how to define the host state's role in the repository siting mechanism. This article explains why these two problems were connected by showing how they proved to be of decisive importance in the development of the Waste Isolation Pilot Plant (WIPP) project in Carlsbad, New Mexico. Although WIPP was initially conceived as a wholly military facility, The Department of Energy triggered a three-year dispute over the project's scope by proposing in 1978 to include commercial wastes in the repository. The key issue in the dispute concerned the political legitimacy of decision-making mechanisms for repository siting, which depend upon the extent to which they both adequately represent the interests of affected groups and meet an indistinct technical/political criterion of acceptable safety. DOE's ill-fated proposal to mix military and commercial disposal at WIPP demonstrated that the two rely on somewhat different conditions for their legitimacy. The agency overlapped the legitimate authorities of the federal and state governments and gave itself the hopeless task of negotiating a new boundary between them. 50 references, 3 figures

Analysis of the potential formation of a Breccia chimney beneath the WIPP repository

International Nuclear Information System (INIS)

Spiegler, P.

1982-05-01

This report evaluates the potential formation of a Breccia pipe beginning at the Bell Canyon aquifer beneath the WIPP repository and the resulting release of radioactivity to the surface. Rock mechanics considerations indicate that the formation of a Breccia pipe by collapse of a cavern is not reasonable. Even if rock mechanics is ignored, the overlying strata act as a barrier and would prevent the release of radioactivity to the biosphere. Gradual formation of a Breccia pipe is so slow that the plutonium-239 in the waste (one of the most important long-lived components) would decay during formation. If Bell Lake and San Simon Sinks are the surface manifestation of a regional deep dissolution wedge, such a wedge is too far removed to represent pipe forming activity near the WIPP site. The formation of a Breccia pipe under the WIPP repository is highly unlikely. If it did occur, the concentration of plutonium-239 in brine reaching the surface would be less than the maximum permissible concentration in water specified in the Code of Federal Regulation Title 10, part 20

Probabilistic modelling of gas generation in nuclear waste repositories under consideration of new studies performed at the WIPP

International Nuclear Information System (INIS)

Niemeyer, M.; Wilhelm, S.; Poppei, J.

2012-01-01

Document available in extended abstract form only. The inventory of a nuclear waste repository includes significant amounts of metal and organic matter. Under the prevailing conditions in a repository in a salt formation in contact with water, these materials tend to react and transform under significant gas production. This increases the pressure and potentially leads to an enhanced transport of radio nuclides. Therefore, these phenomena need to be understood and characterized in detail for the assessment of the safety of the repository A modelling code, GASGEN, developed by AF-Consult Switzerland Ltd to predict the evolution of gas production by microbial processes and anaerobic corrosion of metal, was applied at two locations of repositories in salt rock in Germany. Therein, the microbial decomposition of organic waste components is modelled by the sub-processes of denitrification, reduction of sulphates, fermentation and methano-genesis. The models differentiate between highly degradable cellulose and materials of lesser degradability, such as polymers. Gas production through anaerobic corrosion of metal is mainly due to the iron content of the waste. In addition, the precipitation of carbonate from alkaline materials in the inventory (e.g. cement) is considered. The inventories of contained waste, which determine the amount of gas that can be produced, are subject to uncertainties. The rates of the various reactions also depend on numerous factors and are therefore variable. In order to cover this variability, gas production is modelled probabilistically. In this way the behaviour of the gas generation can be estimated together with its bandwidth Figure 1. In addition to the produced amounts of gas, the model calculations also consider the potential of acidification of the fluid enclosed in the repository chambers and the effect of a changing pH-level on the rate of corrosion. Based on results, the effect of a pH-dependent corrosion rate is illustrated and the

Position paper on flammability concerns associated with TRU waste destined for WIPP

International Nuclear Information System (INIS)

1991-04-01

The Waste Isolation Pilot Plant (WIPP), in southeastern New Mexico,is an underground repository, designed for the safe geologic disposal of transuranic (TRU) wastes generated from defense-related activities of the US Department of Energy (DOE). The WIPP storage rooms are mined in a bedded salt (halite) formation, and are located 2150 feet below the surface. After the disposal of waste in the storage rooms, closure of the repository is expected to occur by creep (plastic flow) of the salt formation, with the waste being permanently isolated from the surrounding environment. This paper has evaluated the issue of flammability concerns associated with TRU waste to be shipped to WIPP, including a review of possible scenarios that can potentially contribute to the flammability. The paper discusses existing regulations that address potential flammability concerns, presents an analysis of previous flammability-related incidents at DOE sites with respect to the current regulations, and finally, examines the degree of assurance these regulations provide in safeguarding against flammability concerns during transportation and waste handling. 50 refs., 7 figs., 7 tabs

Actinide Solubility and Speciation in the WIPP [PowerPoint

International Nuclear Information System (INIS)

Reed, Donald T.

2015-01-01

The presentation begins with the role and need for nuclear repositories (overall concept, international updates (Sweden, Finland, France, China), US approach and current status), then moves on to the WIPP TRU repository concept (design, current status--safety incidents of February 5 and 14, 2014, path forward), and finally considers the WIPP safety case: dissolved actinide concentrations (overall approach, oxidation state distribution and redox control, solubility of actinides, colloidal contribution and microbial effects). The following conclusions are set forth: (1) International programs are moving forward, but at a very slow and somewhat sporadic pace. (2) In the United States, the Salt repository concept, from the perspective of the long-term safety case, remains a viable option for nuclear waste management despite the current operational issues/concerns. (3) Current model/PA prediction (WIPP example) are built on redundant conservatisms. These conservatisms are being addressed in the ongoing and future research to fill existing data gaps--redox control of plutonium by Fe(0, II), thorium (analog) solubility studies in simulated brine, contribution of intrinsic and biocolloids to the mobile concentration, and clarification of microbial ecology and effects.

Actinide Solubility and Speciation in the WIPP [PowerPoint

Energy Technology Data Exchange (ETDEWEB)

Reed, Donald T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-11-02

The presentation begins with the role and need for nuclear repositories (overall concept, international updates (Sweden, Finland, France, China), US approach and current status), then moves on to the WIPP TRU repository concept (design, current status--safety incidents of February 5 and 14, 2014, path forward), and finally considers the WIPP safety case: dissolved actinide concentrations (overall approach, oxidation state distribution and redox control, solubility of actinides, colloidal contribution and microbial effects). The following conclusions are set forth: (1) International programs are moving forward, but at a very slow and somewhat sporadic pace. (2) In the United States, the Salt repository concept, from the perspective of the long-term safety case, remains a viable option for nuclear waste management despite the current operational issues/concerns. (3) Current model/PA prediction (WIPP example) are built on redundant conservatisms. These conservatisms are being addressed in the ongoing and future research to fill existing data gaps--redox control of plutonium by Fe(0, II), thorium (analog) solubility studies in simulated brine, contribution of intrinsic and biocolloids to the mobile concentration, and clarification of microbial ecology and effects.

A methodology of uncertainty/sensitivity analysis for PA of HLW repository learned from 1996 WIPP performance assessment

International Nuclear Information System (INIS)

Lee, Y. M.; Kim, S. K.; Hwang, Y. S.; Kang, C. H.

2002-01-01

The WIPP (Waste Isolation Pilot Plant) is a mined repository constructed by the US DOE for the permanent disposal of transuranic (TRU) wastes generated by activities related to defence of the US since 1970. Its historical disposal operation began in March 1999 following receipt of a final permit from the State of NM after a positive certification decision for the WIPP was issued by the EPA in 1998, as the first licensed facility in the US for the deep geologic disposal of radioactive wastes. The CCA (Compliance Certification Application) for the WIPP that the DOE submitted to the EPA in 1966 was supported by an extensive Performance Assessment (PA) carried out by Sandia National Laboratories (SNL), with so-called 1996 PA. Even though such PA methodologies could be greatly different from the way we consider for HLW disposal in Korea largely due to quite different geologic formations in which repository are likely to be located, a review on lots of works done through the WIPP PA studies could be the most important lessons that we can learn from in view of current situation in Korea where an initial phase of conceptual studies on HLW disposal has been just started. The objective of this work is an overview of the methodology used in the recent WIPP PA to support the US DOE WIPP CCA ans a proposal for Korean case

WIPP: Lessons learned for state/DOE consultation and cooperation

International Nuclear Information System (INIS)

Neill, R.H.

1986-01-01

WIPP is intended to be a repository for permanent disposal of 6,200,000 cu ft of transuranic waste generated from the nation's defense programs. The waste is not fixed, up to 1% can be respirable and it is stored in conventional 17-C Type A Carbon steel drums with a design life of 20 years. (Storage began in 1970). The waste form is not fused in an insoluble glass matrix and there is no commitment by DOE for getters. The question arises of the need and desirability to perform experiments with high level wastes at WIPP. The original purpose in the Oct 1980 WIPP FIES stated ''...the experiments are not so much concerned with the WIPP itself, as they are with planning future high level waste repositories. They are to answer technical questions about the disposal of high level waste in bedded salt and to provide a valid demonstration of the concepts involved.'' The purpose of this paper is to provide information for RH TRU disposal and to generate scientific knowledge that may be helpful to others and not to demonstrate high level waste disposal

Basic data report for drillhole WIPP 13 (Waste isolation pilot plant - WIPP)

International Nuclear Information System (INIS)

1979-10-01

The borehole WIPP-13 was drilled in the SW 1/4 section 17, T22S, R31E of eastern Eddy County during July and August, 1978, to investigate the nature of a resistivity anomaly. The stratigraphic section was normal, consisting of 13 feet of Quaternary deposits (including artificial fill for drill pad), 53 feet of the Triassic Santa Rosa Sandstone, 451 feet of Dewey Lake Red Beds, 269 feet of the Rustler Formation and 179 feet of the upper member of the Salado Formation. Consecutive cores were taken from 570 to 595, 656 to 729, and 827 to 878 feet. Cuttings were collected at 10-foot intervals throughout the rest of the hole. Geophysical logs were run to aid in interpretation of the stratigraphy. The WIPP is to demonstrate (through limited operations) disposal technology for transuranic (TRU) defense wastes. Eventual conversion of the facility to a repository for TRU defense wastes is anticipated. The WIPP will also provide research facilities for interactions between high-level waste and salt

In-Situ Testing and Performance Assessment of a Redesigned WIPP Panel Closure - 13192

Energy Technology Data Exchange (ETDEWEB)

Klein, Thomas [URS-Professional Solutions, 4021 National Parks Highway Carlsbad, NM 88220 (United States); Patterson, Russell [Department of Energy-Carlsbad Field Office, 4021 National Parks Highway Carlsbad, NM 88220 (United States); Camphouse, Chris; Herrick, Courtney; Kirchner, Thomas; Malama, Bwalya; Zeitler, Todd [Sandia National Laboratories-Carlsbad, 4100 National Parks Highway Carlsbad, NM 88220 (United States); Kicker, Dwayne [SM Stoller Corporation-Carlsbad, 4100 National Parks Highway Carlsbad, NM (United States)

2013-07-01

There are two primary regulatory requirements for Panel Closures at the Waste Isolation Pilot Plant (WIPP), the nation's only deep geologic repository for defense related Transuranic (TRU) and Mixed TRU waste. The Federal requirement is through 40 CFR 191 and 194, promulgated by the U.S. Environmental Protection Agency (EPA). The state requirement is regulated through the authority of the Secretary of the New Mexico Environment Department (NMED) under the New Mexico Hazardous Waste Act (HWA), New Mexico Statutes Annotated (NMSA) 1978, chap. 74-4-1 through 74-4-14, in accordance with the New Mexico Hazardous Waste Management Regulations (HWMR), 20.4.1 New Mexico Annotated Code (NMAC). The state regulations are implemented for the operational period of waste emplacement plus 30 years whereas the federal requirements are implemented from the operational period through 10,000 years. The 10,000 year federal requirement is related to the adequate representation of the panel closures in determining long-term performance of the repository. In Condition 1 of the Final Certification Rulemaking for 40 CFR Part 194, the EPA required a specific design for the panel closure system. The U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) has requested, through the Planned Change Request (PCR) process, that the EPA modify Condition 1 via its rulemaking process. The DOE has also requested, through the Permit Modification Request (PMR) process, that the NMED modify the approved panel closure system specified in Permit Attachment G1. The WIPP facility is carved out of a bedded salt formation 655 meters below the surface of southeast New Mexico. Condition 1 of the Final Certification Rulemaking specifies that the waste panels be closed using Option D which is a combination of a Salado mass concrete (SMC) monolith and an isolation/explosion block wall. The Option D design was also accepted as the panel closure of choice by the NMED. After twelve years of waste handling

The WIPP journey to waste receipt

International Nuclear Information System (INIS)

Barnes, G.J.; Whatley, M.E.

1997-01-01

In the early 1970s the federal government selected an area in southeastern New Mexico containing large underground salt beds as potentially suitable for radioactive waste disposal. An extensive site characterization program was initiated by the federal government. This site became the Waste Isolation Pilot Plant, better known as WIPP. It is now 1997, over two decades after the initial selection of the New Mexico site as a potential radioactive waste repository. Numerous scientific studies, construction activities, and environmental compliance documents have been completed. The US Department of Energy (DOE) has addressed all relevant issues regarding the safety of WIPP and its ability to isolate radioactive waste from the accessible environment. Throughout the last two decades up to the present time, DOE has negotiated through a political, regulatory, and legal maze with regard to WIPP. New regulations have been issued, litigation initiated, and public involvement brought to the forefront of the DOE decision-making process. All of these factors combined to bring WIPP to its present status--at the final stages of working through the licensing requirements for receipt of transuranic (TRU) waste for disposal. Throughout its history, the DOE has stayed true to Congress' mandates regarding WIPP. Steps taken have been necessary to demonstrate to Congress, the State of New Mexico, and the public in general, that the nation's first radioactive waste repository will be safe and environmentally sound. DOE's compliance demonstrations are presently under consideration by the cognizant regulatory agencies and DOE is closer than ever to waste receipt. This paper explores the DOE's journey towards implementing a permanent disposal solution for defense-related TRU waste, including major Congressional mandates and other factors that contributed to program changes regarding the WIPP project

Salt Repository Project waste emplacement mode decision paper: Revison 1

International Nuclear Information System (INIS)

1987-08-01

This paper provides a recommendation as to the mode of waste emplacement to be used as the current basis for site characterization activity for the Deaf Smith County, Texas, high level nuclear waste repository site. It also presents a plan for implementing the recommendation so as to provide a high level of confidence in the project's success. Since evaluations of high-level waste disposal in geologic repositories began in the 1950s, most studies emplacement in salt formations employed the vertical orientation for emplacing waste packages in boreholes in the floor of the underground facility. This orientation was used in trials at Project Salt Vault in the 1960s. The Waste Isolation Pilot Plant (WIPP) has recently settled on a combination of vertical and horizontal modes for various waste types. This paper analyzes the information available and develops a project position upon which to base current site characterization activities. The position recommended is that the SRP should continue to use the vertical waste emplacement mode as the reference design and to carry the horizontal mode as a ''passive'' alternative. This position was developed based upon the conclusions of a decision analysis, risk assessment, and cost/schedule impact assessment. 52 refs., 6 figs., 1 tab

Successes and Experiences of the WIPP Project

International Nuclear Information System (INIS)

Chu, Margaret S.Y.; Weart, Wendell D.

2000-01-01

In May 1998, the US Environmental Agency (EPA) certified the US Department of Energy's (DOE) Waste Isolation Pilot Plant (WIPP) as being in compliance with all of the applicable regulations governing the permanent disposal of spent nuclear fuel, high-level waste, and transuranic radioactive waste. The WIPP, a transuranic waste repository, is the first deep geologic repository in the US to have successfully demonstrated regulatory compliance with long-term radioactive waste disposal regulations and be certified to receive wastes. Many lessons were learned throughout the 25-year history of the WIPP--from site selection to the ultimate successful certification. The experiences and lessons learned from the WIPP may be of general interest to other repository programs in the world. The lessons learned include all facets of a repository program: programmatic, managerial, regulatory, technical, and social. This paper addresses critical issues that arose during the 25 years of WIPP history and how they influenced the program

Effects of clay-seam behavior on WIPP repository design

International Nuclear Information System (INIS)

Stone, C.M.; Krieg, R.D.; Branstetter, L.J.

1981-07-01

The geology at the southeastern New Mexico WIPP site consists of bedded layers of rock salt, anhydrite, polyhalite, mixtures of those materials, and thin clay seams. In spite of their very small (0.005 m to 0.05 m) thickness, clay seams are important to structural characterization of the WIPP stratigraphy since slip might possibly take place across them. Results of a study to determine the effects of clay seam frictional slip on the closure of a well-defined drift configuration are described. A Mohr-Coulomb dry friction model was used to model the active clay seams. The main thrust of the study was to determine the effects of friction coefficient variability on drift closure. Results show that the drift closure varies by a factor of 3.0 over the range of friction coefficients studied. The maximum slip observed along any clay seam was 0.12 m. For values of μ > .7, virtually no slip occurs along any clay seam

Proceedings of the 5th US/German Workshop on Salt Repository Research Design and Operation

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Leigh, Christi [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stein, Walter [Karlsruhe Inst. of Technology (KIT) (Germany); Bollingerfehr, Wilhelm [DBE Technology, Peine (Germany); Von Berlepsche, Thilo [DBE Technology, Peine (Germany)

2015-01-01

The 5th US/German Workshop on Salt Repository Research, Design, and Operation was held in Santa Fe New Mexico September 8-10, 2014. The forty seven registered participants were equally divided between the United States (US) and Germany, with one participant from The Netherlands. The agenda for the 2014 workshop was under development immediately upon finishing the 4th Workshop. Ongoing, fundamental topics such as thermomechanical behavior of salt, plugging and sealing, the safety case, and performance assessment continue to advance the basis for disposal of heat-generating nuclear waste in salt formations. The utility of a salt underground research laboratory (URL) remains an intriguing concept engendering discussion of testing protocol. By far the most interest in this years’ workshop pertained to operational safety. Given events at the Waste Isolation Pilot Plant (WIPP), this discussion took on a new sense of relevance and urgency.

The WIPP research and development test program

International Nuclear Information System (INIS)

Tyler, L.D.

1985-01-01

The WIPP (Waste Isolation Pilot Plant) is a DOE RandD Facility for the purpose of developing the technology needed for the safe disposal of the United States defense-related radioactive waste. The in-situ test program is defined for the thermal-structural interactions, plugging and sealing, and waste package interactions in a salt environment. An integrated series of large-scale underground tests address the issues of both systems and long-term isolation performance of a repository

Effects of microbial processes on gas generation under expected WIPP repository conditions: Annual report through 1992

International Nuclear Information System (INIS)

Francis, A.J.; Gillow, J.B.

1993-09-01

Microbial processes involved in gas generation from degradation of the organic constituents of transuranic waste under conditions expected at the Waste Isolation Pilot Plant (WIPP) repository are being investigated at Brookhaven National Laboratory. These laboratory studies are part of the Sandia National Laboratories -- WIPP Gas Generation Program. Gas generation due to microbial degradation of representative cellulosic waste was investigated in short-term ( 6 months) experiments by incubating representative paper (filter paper, paper towels, and tissue) in WIPP brine under initially aerobic (air) and anaerobic (nitrogen) conditions. Samples from the WIPP surficial environment and underground workings harbor gas-producing halophilic microorganisms, the activities of which were studied in short-term experiments. The microorganisms metabolized a variety of organic compounds including cellulose under aerobic, anaerobic, and denitrifying conditions. In long-term experiments, the effects of added nutrients (trace amounts of ammonium nitrate, phosphate, and yeast extract), no nutrients, and nutrients plus excess nitrate on gas production from cellulose degradation

Geotechnical evaluation of the proposed WIPP site in southeast New Mexico

International Nuclear Information System (INIS)

Weart, W.D.

1978-10-01

The Department of Energy is proposing to demonstrate the acceptability of geologic disposal of radioactive waste by locating a Waste Isolation Pilot Plant (WIPP) in the salt beds 26 miles east of Carlsbad, New Mexico. The WIPP will serve as a permanent repository for defense generated transuranic contaminated waste and will also be used as a facility in which experiments and demonstrations with all radioactive waste types can be conducted. The present area being proposed for the WIPP is the second such location in the Delaware Basin for which new site data have been developed; the first site proved geologically unacceptable. Ecologic and socioeconomic aspects have been investigated and extensive geophysical, geological and hydrologic studies have been conducted to allow an evaluation of site acceptability. Geotechnical aspects of site characterization are examined. These studies are now sufficiently complete that the site can be recommended for further development of the WIPP

WIPP performance assessment: impacts of human intrusion

International Nuclear Information System (INIS)

Anderson, D.R.; Hunter, R.L.; Bertram-Howery, S.G.; Lappin, A.R.

1989-01-01

The Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico is a research and development facility that may become the USA's first and only mined geologic repository for transuranic waste. Human intrusion into the WIPP repository after closure has been shown by preliminary sensitivity analyses and calculations of consequences to be an important, and perhaps the most important, factor in long-term repository performance

Modification of the ventilation system at Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Sethi, S.C.

1987-01-01

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico, is a research and development project sponsored by the US Department of Energy, designed to demonstrate the safe disposal of radioactive waste. A mine (repository) is being developed 2,150 feet below the surface in a thick salt bed, which will serve as the disposal medium. The underground ventilation system for the WIPP project was originally designed based on a fixed project scope. The design criteria and ventilation requirements were developed for the performance of various activities as then envisioned towards the achievement of this goal. However, in light of new information and actual site-specific experience at WIPP leading to a clearer definition of the scope-related programs and activities, it was realized that the existing ventilation system may need to be modified

Scientific studies in support of the Waste Isolation Pilot Plant (WIPP) repository

International Nuclear Information System (INIS)

Chu, M.S.Y.; Weart, W.D.

1996-01-01

The DOE submitted a Compliance Certification Application for WIPP in october, 1996. A critical part of this application was a Performance Assessment which predicts the cumulative radioactive release to the accessible environment over a time period of 10,000 years. Comparison of this predicted release to the EPA standard shows a comfortable margin of compliance. The scientific understanding that was critical to developing this assessment spans a broad range of geotechnical disciplines, and required a thorough understanding of the site's geology and hydrology. Evaluation of the geologic processes which are active in the site region establishes that there will be no natural breach of site integrity for millions of years, far longer than the 10,000 year regulatory period. Inadvertent human intrusion is, therefore, the only credible scenario to lead to potential radioactive release to the accessible environment. To substantiate this conclusion and to quantify these potential releases from human intrusion, it has been necessary to develop an understanding of the following processes: salt creep and shaft seal efficacy; gas generation from organic decomposition of waste materials and anoxic corrosion of metals in the waste and waste packages; solubilities for actinides in brine; fluid flow in Salado formation rocks, and hydrologic transport of actinides in the overlying dolomite aquifers. Other issues which had to be evaluated to allow definition of breach scenarios were brine reservoir occurrences and their associated reservoir parameters, consequences of mining over the repository, and drilling for natural resources in the vicinity of the repository. Results of all these studies will be briefly summarized in this paper

9+ years of disposal experience at the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Rempe, Norbert T.; Nelson, Roger A.

2008-01-01

With almost a decade of operating experience, the Waste Isolation Pilot Plant (WIPP) has established an enviable record by clearly demonstrating that a deep geologic repository for unconditioned radioactive waste in rock salt can be operated safely and in compliance with very complex regulations. WIPP has disposed of contact-handled transuranic (TRU) waste since 1999 and remote-handled TRU waste since 2007. Emplacement methods range from directly stacking unshielded 0.21-4.5 m 3 containers inside disposal rooms to remotely inserting highly radioactive 0.89 m 3 canisters into horizontally drilled holes (shield plugs placed in front of canisters protect workers inside active disposal rooms). More than 100 000 waste containers have been emplaced, and one-third of WIPP's authorized repository capacity of 175,000 m 3 has already been consumed. Principal surface operations are conducted in the waste handling building, which is divided into CH and RH waste handling areas. Four vertical shafts extend from the surface to the disposal horizon, 655 m below the surface in a 1000 m thick sequence of Permian bedded salt. The waste disposal area of about 0.5 km 2 is divided into ten panels, each consisting of seven rooms. Vertical closure (creep) rates in disposal rooms range up to 10 cm per year. While one panel is being filled with waste, the next one is being mined. Mined salt is raised to the surface in the salt shaft, and waste is lowered down the waste shaft. Both of these shafts also serve as principal access for personnel and materials. Underground ventilation is divided into separate flow paths, allowing simultaneous mining and disposal. A filter building near the exhaust shaft provides the capability to filter the exhaust air (in reduced ventilation mode) through HEPA filters before release to the atmosphere. WIPP operations have not exposed employees or the public to radiation doses beyond natural background variability. They consistently meet or exceed regulatory

Status Report on the Microbial Characterization of Halite and Groundwater Samples from the WIPP

International Nuclear Information System (INIS)

Swanson, Juliet S.; Reed, Donald T.; Ams, David A.; Norden, Diana; Simmons, Karen A.

2012-01-01

This report summarizes the progress made in the ongoing task of characterizing the microbial community structures within the WIPP repository and in surrounding groundwaters. Through cultivation and DNA-based identification, the potential activity of these organisms is being inferred, thus leading to a better understanding of their impact on WIPP performance. Members of the three biological domains - Bacteria, Archaea, and Eukarya (in this case, Fungi) - that are associated with WIPP halite have been identified. Thus far, their activity has been limited to aerobic respiration; anaerobic incubations are underway. WIPP halite constitutes the near-field microbial environment. We expect that microbial activity in this setting will proceed from aerobic respiration, through nitrate reduction to focus on sulfate reduction. This is also the current WIPP performance assessment (PA) position. Sulfate reduction can occur at extremely high ionic strengths, and sulfate is available in WIPP brines and in the anhydrite interbeds. The role of methanogenesis in the WIPP remains unclear, due to both energetic constraints imposed by a high-salt environment and substrate selectivity, and it is no longer considered in PA. Archaea identified in WIPP halite thus far fall exclusively within the family Halobacteriaceae. These include Halobacterium noricense, cultivated from both low- and high-salt media, and a Halorubrum-like species. The former has also been detected in other salt mines worldwide; the latter likely constitutes a new species. Little is known of its function, but it was prevalent in experiments investigating the biodegradation of organic complexing agents in WIPP brines. Bacterial signatures associated with WIPP halite include members of the phylum Proteobacteria - Halomonas, Pelomonas, Limnobacter, and Chromohalobacter - but only the latter has been isolated. Also detected and cultivated were Salinicoccus and Nesterenkonia spp. Fungi were also isolated from halite. Although

Status Report on the Microbial Characterization of Halite and Groundwater Samples from the WIPP

Energy Technology Data Exchange (ETDEWEB)

Swanson, Juliet S. [Los Alamos National Laboratory; Reed, Donald T. [Los Alamos National Laboratory; Ams, David A. [Los Alamos National Laboratory; Norden, Diana [Ohio State University; Simmons, Karen A. [Los Alamos National Laboratory

2012-07-10

This report summarizes the progress made in the ongoing task of characterizing the microbial community structures within the WIPP repository and in surrounding groundwaters. Through cultivation and DNA-based identification, the potential activity of these organisms is being inferred, thus leading to a better understanding of their impact on WIPP performance. Members of the three biological domains - Bacteria, Archaea, and Eukarya (in this case, Fungi) - that are associated with WIPP halite have been identified. Thus far, their activity has been limited to aerobic respiration; anaerobic incubations are underway. WIPP halite constitutes the near-field microbial environment. We expect that microbial activity in this setting will proceed from aerobic respiration, through nitrate reduction to focus on sulfate reduction. This is also the current WIPP performance assessment (PA) position. Sulfate reduction can occur at extremely high ionic strengths, and sulfate is available in WIPP brines and in the anhydrite interbeds. The role of methanogenesis in the WIPP remains unclear, due to both energetic constraints imposed by a high-salt environment and substrate selectivity, and it is no longer considered in PA. Archaea identified in WIPP halite thus far fall exclusively within the family Halobacteriaceae. These include Halobacterium noricense, cultivated from both low- and high-salt media, and a Halorubrum-like species. The former has also been detected in other salt mines worldwide; the latter likely constitutes a new species. Little is known of its function, but it was prevalent in experiments investigating the biodegradation of organic complexing agents in WIPP brines. Bacterial signatures associated with WIPP halite include members of the phylum Proteobacteria - Halomonas, Pelomonas, Limnobacter, and Chromohalobacter - but only the latter has been isolated. Also detected and cultivated were Salinicoccus and Nesterenkonia spp. Fungi were also isolated from halite. Although

The influence of salt aerosol on alpha radiation detection by WIPP continuous air monitors

International Nuclear Information System (INIS)

Bartlett, W.T.; Walker, B.A.

1996-01-01

Alpha continuous air monitors (CAMs) will be used at the Waste Isolation Pilot Plant (WIPP) to measure airborne transuranic radioactivity that might be present in air exhaust or in work-place areas. WIPP CAMs are important to health and safety because they are used to alert workers to airborne radioactivity, to actuate air-effluent filtration systems, and to detect airborne radioactivity so that the radioactivity can be confined in a limited area. In 1993, the Environmental Evaluation Group (EEG) reported that CAM operational performance was affected by salt aerosol, and subsequently, the WIPP CAM design and usage were modified. In this report, operational data and current theories on aerosol collection were reviewed to determine CAM quantitative performance limitations. Since 1993, the overall CAM performance appears to have improved, but anomalous alpha spectra are present when sampling-filter salt deposits are at normal to high levels. This report shows that sampling-filter salt deposits directly affect radon-thoron daughter alpha spectra and overall monitor efficiency. Previously it was assumed that aerosol was mechanically collected on the surface of CAM sampling filters, but this review suggests that electrostatic and other particle collection mechanisms are more important than previously thought. The mechanism of sampling-filter particle collection is critical to measurement of acute releases of radioactivity. 41 refs

WIPP radiation dosimetry program

International Nuclear Information System (INIS)

Wu, C.F.

1991-01-01

Radiation dosimetry is the process by which various measurement results and procedures are applied to quantify the radiation exposure of an individual. Accurate and precise determination of radiation dose is a key factor to the success of a radiation protection program. The Waste Isolation Pilot Plant (WIPP), a Department of Energy (DOE) facility designed for permanent repository of transuranic wastes in a 2000-foot-thick salt bed 2150 feet underground, has established a dosimetry program developed to meet the requirements of DOE Order 5480.11, ''Radiation Protection for Occupational Workers''; ANSI/ASME NQA-1, ''Quality Assurance Program Requirements for Nuclear Facilities''; DOE Order 5484.1, ''Environmental Protection, Safety, and Health Protection Information Reporting Requirements''; and other applicable regulations

Laboratory creep and mechanical tests on salt data report (1975-1996): Waste Isolation Pilot Plant (WIPP) thermal/structural interactions program

Energy Technology Data Exchange (ETDEWEB)

Mellegard, K.D. [RE/SPEC Inc., Rapid City, SD (United States); Munson, D.E. [Sandia National Labs., Albuquerque, NM (United States)

1997-02-01

The Waste Isolation Pilot Plant (WIPP), a facility located in a bedded salt formation in Carlsbad, New Mexico, is being used by the U.S. Department of Energy to demonstrate the technology for safe handling and disposal of transuranic wastes produced by defense activities in the United States. In support of that demonstration, mechanical tests on salt were conducted in the laboratory to characterize material behavior at the stresses and temperatures expected for a nuclear waste repository. Many of those laboratory test programs have been carried out in the RE/SPEC Inc. rock mechanics laboratory in Rapid City, South Dakota; the first program being authorized in 1975 followed by additional testing programs that continue to the present. All of the WIPP laboratory data generated on salt at RE/SPEC Inc. over the last 20 years is presented in this data report. A variety of test procedures were used in performance of the work including quasi-static triaxial compression tests, constant stress (creep) tests, damage recovery tests, and multiaxial creep tests. The detailed data is presented in individual plots for each specimen tested. Typically, the controlled test conditions applied to each specimen are presented in a plot followed by additional plots of the measured specimen response. Extensive tables are included to summarize the tests that were performed. Both the tables and the plots contain cross-references to the technical reports where the data were originally reported. Also included are general descriptions of laboratory facilities, equipment, and procedures used to perform the work.

Chemistry of brines in salt from the Waste Isolation Pilot Plant (WIPP), southeastern New Mexico: a preliminary investigation

International Nuclear Information System (INIS)

Stein, C.L.; Krumhansl, J.L.

1986-03-01

We present here analyses of macro- and microscopic (intracrystalline) brines observed within the WIPP facility and in the surrounding halite, with interpretations regarding the origin and history of these fluids and their potential effect(s) on long-term waste storage. During excavation, several large fluid inclusions were recovered from an area of highly recrystallized halite in a thick salt bed at the repository horizon (2150 ft below ground level). In addition, 52 samples of brine ''weeps'' were collected from walls of recently excavated drifts at the same stratigraphic horizon from which the fluid inclusion samples are assumed to have been taken. Analyses of these fluids show that they differ substantially in composition from the inclusion fluids and cannot be explained by mixing of the fluid inclusion populations. Finally, holes in the facility floor that filled with brine were sampled but with no stratographic control; therefore it is not possible to interpret the compositions of these brines with any accuracy, except insofar as they resemble the weep compositions but with greater variation in both K/Mg and Na/Cl ratios. However, the Ca and SO 4 values for the floor holes are relatively close to the gypsum saturation curve, suggesting that brines filling floor holes have been modified by the presence of gypsum or anhydrite, possibly even originating in one or more of the laterally continuous anhydrite units referred to in the WIPP literature as marker beds. In conclusion, the wide compositional variety of fluids found in the WIPP workings suggest that (1) an interconnected hydrologic system which could effectively transport radonuclides away from the repository does not exist; (2) brine migration studies and experiments must consider the mobility of intergranular fluids as well as those in inclusions; and (3) near- and far-field radionuclide migration testing programs need to consider a wide range of brine compositions rather than a few reference brines

Leveraging Radioactive Waste Disposal at WIPP for Science

Science.gov (United States)

Rempe, N. T.

2008-12-01

Salt mines are radiologically much quieter than other underground environments because of ultra-low concentrations of natural radionuclides (U, Th, and K) in the host rock; therefore, the Waste Isolation Pilot Plant (WIPP), a government-owned, 655m deep geologic repository that disposes of radioactive waste in thick salt near Carlsbad, New Mexico, has for the last 15 years hosted highly radiation-sensitive experiments. Incidentally, Nature started her own low background experiment 250ma ago, preserving viable bacteria, cellulose, and DNA in WIPP salt. The Department of Energy continues to make areas of the WIPP underground available for experiments, freely offering its infrastructure and access to this unique environment. Even before WIPP started disposing of waste in 1999, the Room-Q alcove (25m x 10m x 4m) housed a succession of small experiments. They included development and calibration of neutral-current detectors by Los Alamos National Laboratory (LANL) for the Sudbury Neutrino Observatory, a proof-of-concept by Ohio State University of a flavor-sensitive neutrino detector for supernovae, and research by LANL on small solid- state dark matter detectors. Two currently active experiments support the search for neutrino-less double beta decay as a tool to better define the nature and mass of the neutrino. That these delicate experiments are conducted in close vicinity to, but not at all affected by, megacuries of radioactive waste reinforces the safety argument for the repository. Since 2003, the Majorana collaboration is developing and testing various detector designs inside a custom- built clean room in the Room-Q alcove. Already low natural background readings are reduced further by segmenting the germanium detectors, which spatially and temporally discriminates background radiation. The collaboration also demonstrated safe copper electro-forming underground, which minimizes cosmogenic background in detector assemblies. The largest currently used experimental

Champion for radioactive waste disposal host of the WIPP: Carlsbad, New Mexico

International Nuclear Information System (INIS)

Rempe, N.T.

1995-01-01

The city of Carlsbad, New Mexico, volunteered to host the United States' first final repository for radioactive waste. Carlsbad citizens and their leaders understood that after decades of accumulating waste, the time had come to close the nuclear cycle. They therefore agreed to support the Waste Isolation Pilot Plant (WIPP), provided the project would not endanger its neighbors or the environment. The southeastern New Mexico area offers several advantages for deep geologic waste disposal: The regional geology is well understood. Massive salt beds are an excellent repository medium. Decades of potash mining experience inspired confidence in that concept. In underground nuclear test in the salt had caused no harm. And the city was seeking opportunities to diversify its economic base. Through the growth of the project, beginning in 1971, Carlsbad has demonstrated unwavering commitment, patience, and persistence. Without these attitudes, the WIPP would certainly not be where it is today and most likely would not exist at all. Civic leaders made the critical difference as the project weathered repeated challenges. With the support of their constituents, they foiled anti-nuclear obstructionism and advanced the project at every turn, frequently on their own time and at their own expense. The WIPP is now scheduled to start disposal in 1998, after a ten-year delay from its originally intended opening date. If it still has a realistic chance to start operations before the end of the century, the credit must in no small measure go to the city and the citizens of Carlsbad, New Mexico

Pretest characterization of WIPP experimental waste

International Nuclear Information System (INIS)

Johnson, J.; Davis, H.

1991-01-01

The Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico, is an underground repository designed for the storage and disposal of transuranic (TRU) wastes from US Department of Energy (DOE) facilities across the country. The Performance Assessment (PA) studies for WIPP address compliance of the repository with applicable regulations, and include full-scale experiments to be performed at the WIPP site. These experiments are the bin-scale and alcove tests to be conducted by Sandia National Laboratories (SNL). Prior to conducting these experiments, the waste to be used in these tests needs to be characterized to provide data on the initial conditions for these experiments. This characterization is referred to as the Pretest Characterization of WIPP Experimental Waste, and is also expected to provide input to other programmatic efforts related to waste characterization. The purpose of this paper is to describe the pretest waste characterization activities currently in progress for the WIPP bin-scale waste, and to discuss the program plan and specific analytical protocols being developed for this characterization. The relationship between different programs and documents related to waste characterization efforts is also highlighted in this paper

Status and Growth of Underground Science at WIPP

Science.gov (United States)

Rempe, Norbert T.

2008-10-01

The science community is increasingly taking advantage of research opportunities in the government-owned Waste Isolation Pilot Plant (WIPP), 655m underground near Carlsbad, NM. Discoveries so far include viable bacteria, cellulose, and DNA in 250 million-year old salt, preserved in an ultra-low background-radiation setting. Supplementing the overburden's shielding against cosmic radiation, terrestrial background from the host formation is less than five percent that of average crustal rock. In the past, WIPP accommodated development and testing of neutral current detectors for the Sudbury Neutrino Observatory and dark matter research, and it currently hosts two experiments pursuing neutrino-less double-beta decay. That scientists can listen to whispers from the universe in proximity to megacuries of radioactive waste lends, of course, credibility to the argument that WIPP itself is very safe. Almost a century of regional petroleum and potash extraction history and more than three decades of WIPP studies have generated a comprehensive body of knowledge on geology, mining technology, rock mechanics, geochemistry, and other disciplines relevant to underground science. Existing infrastructure is being used and can be expanded to fit experimental needs. WIPP's exemplary safety and regulatory compliance culture, low excavating and operating cost, and the high probability of the repository operating at least another 40 years make its available underground space attractive for future research and development. Recent proposals include low-photon energy counting to study internal dose received decades ago, investigations into ultra-low radiation dose response in cell cultures and laboratory animals (e.g., hormesis vs. linear no-threshold) and detectors for dark matter, solar and supernova neutrinos, and proton decay. Additional proposals compatible with WIPP's primary mission are welcome.

Geotechnical Perspectives on the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Francke, Chris T.; Hansen, Frank D.; Knowles, M. Kathyn; Patchet, Stanley J.; Rempe, Norbert T.

1999-01-01

The Waste Isolation Pilot Plant (WIPP) is the first nuclear waste repository certified by the United States Environmental Protection Agency. Success in regulatory compliance resulted from an excellent natural setting for such a repository, a facility with multiple, redundant safety systems, and from a rigorous, transparent scientific and technical evaluation. The WIPP story, which has evolved over the past 25 years, has generated a library of publications and analyses. Details of the multifaceted program are contained in the cited references. Selected geotechnical highlights prove the eminent suitability of the WIPP to serve its congressionally mandated purpose

Reference repository design concept for bedded salt

Energy Technology Data Exchange (ETDEWEB)

Carpenter, D.W.; Martin, R.W.

1980-10-08

A reference design concept is presented for the subsurface portions of a nuclear waste repository in bedded salt. General geologic, geotechnical, hydrologic and geochemical data as well as descriptions of the physical systems are provided for use on generic analyses of the pre- and post-sealing performance of repositories in this geologic medium. The geology of bedded salt deposits and the regional and repository horizon stratigraphy are discussed. Structural features of salt beds including discontinuities and dissolution features are presented and their effect on repository performance is discussed. Seismic hazards and the potential effects of earthquakes on underground repositories are presented. The effect on structural stability and worker safety during construction from hydrocarbon and inorganic gases is described. Geohydrologic considerations including regional hydrology, repository scale hydrology and several hydrological failure modes are presented in detail as well as the hydrological considerations that effect repository design. Operational phase performance is discussed with respect to operations, ventilation system, shaft conveyances, waste handling and retrieval systems and receival rates of nuclear waste. Performance analysis of the post sealing period of a nuclear repository is discussed, and parameters to be used in such an analysis are presented along with regulatory constraints. Some judgements are made regarding hydrologic failure scenarios. Finally, the design and licensing process, consistent with the current licensing procedure is described in a format that can be easily understood.

Reference repository design concept for bedded salt

International Nuclear Information System (INIS)

Carpenter, D.W.; Martin, R.W.

1980-01-01

A reference design concept is presented for the subsurface portions of a nuclear waste repository in bedded salt. General geologic, geotechnical, hydrologic and geochemical data as well as descriptions of the physical systems are provided for use on generic analyses of the pre- and post-sealing performance of repositories in this geologic medium. The geology of bedded salt deposits and the regional and repository horizon stratigraphy are discussed. Structural features of salt beds including discontinuities and dissolution features are presented and their effect on repository performance is discussed. Seismic hazards and the potential effects of earthquakes on underground repositories are presented. The effect on structural stability and worker safety during construction from hydrocarbon and inorganic gases is described. Geohydrologic considerations including regional hydrology, repository scale hydrology and several hydrological failure modes are presented in detail as well as the hydrological considerations that effect repository design. Operational phase performance is discussed with respect to operations, ventilation system, shaft conveyances, waste handling and retrieval systems and receival rates of nuclear waste. Performance analysis of the post sealing period of a nuclear repository is discussed, and parameters to be used in such an analysis are presented along with regulatory constraints. Some judgements are made regarding hydrologic failure scenarios. Finally, the design and licensing process, consistent with the current licensing procedure is described in a format that can be easily understood

WIPP Magnesium Oxide (MgO) - Planned Change Request

Science.gov (United States)

On April 10, 2006, the DOE submitted a planned change request pertaining to the amount of MgO emplaced in the WIPP repository. MgO is an engineered barrier that DOE included as part of the original WIPP Certification Decision.

Comparison between predicted and measured south drift closures at the WIPP using a transient creep model for salt

International Nuclear Information System (INIS)

Munson, D.E.; Fossum, A.F.

1986-01-01

The US Department of Energy is constructing and operating the Waste Isolation Pilot Plant (WIPP), a research and development facility near Carlsbad, New Mexico, to determine whether or not defense-generated high-level radioactive waste can be stored safely in bedded salt. The goal of the WIPP modeling program is to develop the capability to predict room responses from one site to another without a priori knowledge of the actual room responses. Data from one of the early WIPP excavations, called the South Drift, have already been used to form an initial evaluation of computational models for predicting room closures as a result of salt creep. In that study, a significant unresolved discrepancy existed between predicted and measured room closures. It was suggested that future studies address alternate forms of the constitutive law. In this paper, an alternate form of the creep model for salt is used that is founded upon the deformation-mechanism map for the micromechanical deformation processes. This model embodies both steady-state and transient creep. Also, quasi-static plasticity is incorporated into the complete constitutive model for salt. The conclusion is drawn that the combination of the mechanistic creep model, plasticity, and flow potential can approximate the late time South Drift deformation. Further improvement of the model fit of plasticity in the future is expected to further improve the simulation

Radioactive waste disposal: Waste isolation pilot plants (WIPP). (Latest citations from the NTIS Bibliographic database). Published Search

International Nuclear Information System (INIS)

1993-09-01

The bibliography contains citations concerning the Waste Isolation Pilot Plant (WIPP), a geologic repository located in New Mexico for transuranic wastes generated by the U.S. Government. Articles follow the development of the program from initial site selection and characterization through construction and testing, and examine research programs on environmental impacts, structural design, and radionuclide landfill gases. Existing plants and facilities, pilot plants, migration, rock mechanics, economics, regulations, and transport of wastes to the site are also included. The Salt Repository Project and the Crystalline Repository Project are referenced in separate bibliographies. (Contains a minimum of 228 citations and includes a subject term index and title list.)

Grouts and concretes for the Waste Isolation Pilot Project (WIPP)

International Nuclear Information System (INIS)

Wakeley, L.D.

1990-01-01

The Structures Laboratory of the U.S. Army Engineer Waterways Experiment Station has conducted research on cement-based composites for the Waste Isolation Pilot Project (WIPP) since 1977, in cooperation with Sandia National Laboratories. Field testing requirements guided initial development of grouts. Concurrent and later laboratory studies explored the chemical stability and probable durability of these mixtures. Beginning in 1985, a series of small-scale seal performance tests at the WIPP prompted development of an expansive salt-saturated concrete. Important lessons learned from this ongoing work include: (1) carefully tailored mixtures can tolerate phase changes involving Ca, Al, and SO 4 , without loss of structural integrity; (2) handling and placement properties are probably more crucial to the mixtures than is exact phase composition; and (3) for the environment of a geologic repository, demonstrated chemical durability will be the best indicator of long-term performance

WIPP: a perspective from ten years of operating success - 16189

International Nuclear Information System (INIS)

Gregory, Phillip C.

2009-01-01

The Waste Isolation Pilot Plant (WIPP), located 35 miles east of Carlsbad, New Mexico, USA is the first and, to the author's knowledge, only facility in the world for the permanent disposal of defense related transuranic (TRU) waste. Soon after plutonium was first synthesized in 1940 by a team of scientists at the University of California Berkeley Laboratory, the need to find a permanent repository for plutonium contaminated waste was recognized due to the more than 24,000 year half-life of Plutonium-239 ( 239 Pu). In 1957 the National Academy of Sciences published a report recommending deep geological burial in bedded salt as a possible solution. However, more than 50 years passed before the solution was achieved when in 1999 WIPP received the first shipment of TRU waste from Los Alamos National Laboratory. Ten years later, more than 7,600 shipments of TRU waste have been disposed of in rooms mined in an ancient salt bed more than 2,000 feet underground. This paper provides a brief history of WIPP with an overview of the technical, regulatory, and political hurdles that had to be overcome before the idea of a permanent disposal facility became reality. The paper focuses primarily on the safe, uneventful transportation program that has moved 100,000- plus containers of TRU waste from various U.S. Department of Energy (DOE) generator and/or storage sites across the Unites States to southeastern New Mexico. (author)

WIPP operations planning: an overview

International Nuclear Information System (INIS)

Miskimin, P.A.; Cossel, S.C.; Plung, D.L.

1985-01-01

The Waste Isolation Pilot Plant (WIPP) is the first-of-a-kind facility for emplacement of radioactive waste in a geologic repository. The concern for safe and efficient operations - coupled with the domestic and international significance of this project - necessitates that WIPP be a ''model plant.'' To develop WIPP as a model plant, a unique planning methodology was employed to identify, evaluate, incorporate, and implement these elements that together will form the best possible overall operation. The resulting improvements in communication among project participants and the smooth transition being made from construction are equally attributable to the methodology employed and the operating program plan developed. 1 fig

Thermodynamic Properties of Magnesium Chloride Hydroxide Hydrate (Mg3Cl(OH)5:4H2O, Phase 5), and Its importance to Nuclear Waste Isolation in Geological Repositories in Salt Formations

Science.gov (United States)

Xiong, Y.; Deng, H.; Nemer, M. B.; Johnsen, S.

2009-12-01

MgO (bulk, pure MgO corresponding to the mineral periclase) is the only engineered barrier certified by the Environmental Protection Agency for emplacement in the Waste Isolation Pilot Plant (WIPP) in the US, and an Mg(OH)2-based engineered barrier (bulk, pure Mg(OH)2 corresponding to brucite) is to be employed in the Asse repository in Germany. Both the WIPP and the Asse are located in salt formations. The WIPP is a U.S. Department of Energy geological repository being used for the permanent disposal of defense-related transuranic waste (TRU waste). The repository is 655 m below the surface, and is situated in the Salado Formation, a Permian salt bed mainly composed of halite, and of lesser amounts of polyhalite, anhydrite, gypsum, magnesite, clays and quartz. The WIPP Generic Weep Brine (GWB), a Na-Mg-Cl dominated brine, is associated with the Salado Formation. The previous vendor for MgO for the WIPP was Premier Chemicals and the current vendor is Martin Marietta Materials. Experimental studies of both Premier MgO and Martin Marietta MgO with the GWB at SNL indicate the formation of magnesium chloride hydroxide hydrate, Mg3Cl(OH)5:4H2O, termed as phase 5. However, this important phase is lacking in the existing thermodynamic database. In this study, the solubility constant of phase 5 is determined from a series of solubility experiments in MgCl2-NaCl solutions. The solubility constant at 25 oC for the following reaction, Mg3Cl(OH)5:4H2O + 5H+ = 3Mg2+ + 9H2O(l) + Cl- is recommended as 43.21±0.33 (2σ) based on the Specific Interaction Theory (SIT) model for extrapolation to infinite dilution. The log K obtained via the Pitzer equations is identical to the above value within the quoted uncertainty. The Gibbs free energy and enthalpy of formation for phase 5 at 25 oC are derived as -3384±2 (2σ) kJ mol-1 and -3896±6 (2σ) kJ mol-1, respectively. The standard entropy and heat capacity of phase 5 at 25 oC are estimated as 393±20 J mol-1 K-1 and 374±19 J mol-1 K

Salt repository project closeout status report

International Nuclear Information System (INIS)

1988-06-01

This report provides an overview of the scope and status of the US Department of Energy (DOE's) Salt Repository Project (SRP) at the time when the project was terminated by the Nuclear Waste Policy Amendments Act of 1987. The report reviews the 10-year program of siting a geologic repository for high-level nuclear waste in rock salt formations. Its purpose is to aid persons interested in the information developed during the course of this effort. Each area is briefly described and the major items of information are noted. This report, the three salt Environmental Assessments, and the Site Characterization Plan are the suggested starting points for any search of the literature and information developed by the program participants. Prior to termination, DOE was preparing to characterize three candidate sites for the first mined geologic repository for the permanent disposal of high-level nuclear waste. The sites were in Nevada, a site in volcanic tuff; Texas, a site in bedded salt (halite); and Washington, a site in basalt. These sites, identified by the screening process described in Chapter 3, were selected from the nine potentially acceptable sites shown on Figure I-1. These sites were identified in accordance with provisions of the Nuclear Waste Policy Act of 1982. 196 refs., 21 figs., 11 tabs

Monitored retrievable storage (MRS) facility and salt repository integration: Engineering study report

International Nuclear Information System (INIS)

1987-07-01

This MRS Facility and Salt Repository Integration Study evaluates the impacts of an integrated MRS/Salt Repository Waste Management System on the Salt Repository Surface facilities' design, operations, cost, and schedule. Eight separate cases were studied ranging from a two phase repository design with no MRS facility to a design in which the repository only received package waste from the MRS facility for emplacement. The addition of the MRS facility to the Waste Management System significantly reduced the capital cost of the salt repository. All but one of the cases studied were capable of meeting the waste acceptance data. The reduction in the size and complexity of the Salt Repository waste handling building with the integration of the MRS facility reduces the design and operating staff requirements. 7 refs., 35 figs., 43 tabs

Schematic designs for penetration seals for a reference repository in bedded salt

International Nuclear Information System (INIS)

Kelsall, P.C.; Case, J.B.; Meyer, D.; Coons, W.E.

1982-11-01

The isolation of radioactive wastes in geologic repositories requires that man-made penetrations such as shafts, tunnels, or boreholes are adequately sealed. This report describes schematic seal designs for a repository in bedded salt referenced to the straitigraphy of southeastern New Mexico. The designs are presented for extensive peer review and will be updated as site-specific conceptual designs when a site for a repository in salt has been selected. The principal material used in the seal system is crushed salt obtained from excavating the repository. It is anticipated that crushed salt will consolidate as the repository rooms creep close to the degree that mechanical and hydrologic properties will eventually match those of undisturbed, intact salt. For southeastern New Mexico salt, analyses indicate that this process will require approximately 1000 years for a seal located at the base of one of the repository shafts (where there is little increase in temperature due to waste emplacement) and approximately 400 years for a seal located in an access tunnel within the repository. Bulkheads composed of contrete or salt bricks are also included in the seal system as components which will have low permeability during the period required for salt consolidation

WIPP shaft seal system parameters recommended to support compliance calculations

International Nuclear Information System (INIS)

Hurtado, L.D.; Knowles, M.K.; Kelley, V.A.; Jones, T.L.; Ogintz, J.B.; Pfeifle, T.W.

1997-12-01

The US Department of Energy plans to dispose of transuranic waste at the Waste Isolation Pilot Plant (WIPP), which is sited in southeastern New Mexico. The WIPP disposal facility is located approximately 2,150 feet (650 m) below surface in the bedded halite of the Salado Formation. Prior to initiation of disposal activities, the Department of Energy must demonstrate that the WIPP will comply with all regulatory requirements. Applicable regulations require that contaminant releases from the WIPP remain below specified levels for a period of 10,000 years. To demonstrate that the WIPP will comply with these regulations, the Department of Energy has requested that Sandia National Laboratories develop and implement a comprehensive performance assessment of the WIPP repository for the regulatory period. This document presents the conceptual model of the shaft sealing system to be implemented in performance assessment calculations conducted in support of the Compliance Certification Application for the WIPP. The model was developed for use in repository-scale calculations and includes the seal system geometry and materials to be used in grid development as well as all parameters needed to describe the seal materials. These calculations predict the hydrologic behavior of the system. Hence conceptual model development is limited to those processes that could impact the fluid flow through the seal system

WIPP shaft seal system parameters recommended to support compliance calculations

Energy Technology Data Exchange (ETDEWEB)

Hurtado, L.D.; Knowles, M.K. [Sandia National Labs., Albuquerque, NM (United States); Kelley, V.A.; Jones, T.L.; Ogintz, J.B. [INTERA Inc., Austin, TX (United States); Pfeifle, T.W. [RE/SPEC, Inc., Rapid City, SD (United States)

1997-12-01

The US Department of Energy plans to dispose of transuranic waste at the Waste Isolation Pilot Plant (WIPP), which is sited in southeastern New Mexico. The WIPP disposal facility is located approximately 2,150 feet (650 m) below surface in the bedded halite of the Salado Formation. Prior to initiation of disposal activities, the Department of Energy must demonstrate that the WIPP will comply with all regulatory requirements. Applicable regulations require that contaminant releases from the WIPP remain below specified levels for a period of 10,000 years. To demonstrate that the WIPP will comply with these regulations, the Department of Energy has requested that Sandia National Laboratories develop and implement a comprehensive performance assessment of the WIPP repository for the regulatory period. This document presents the conceptual model of the shaft sealing system to be implemented in performance assessment calculations conducted in support of the Compliance Certification Application for the WIPP. The model was developed for use in repository-scale calculations and includes the seal system geometry and materials to be used in grid development as well as all parameters needed to describe the seal materials. These calculations predict the hydrologic behavior of the system. Hence conceptual model development is limited to those processes that could impact the fluid flow through the seal system.

The WIPP research and development program: providing the technical basis for defense waste disposal

International Nuclear Information System (INIS)

Hunter, Th.O.

1983-01-01

The Waste Isolation Pilot Plant (WIPP), located in southeastern New Mexico, is being developed by the US Department of Energy as a research and development facility to demonstrate the safe disposal of radioactive wastes from the defense programs of the United States. Underground workings are at a depth of 660 in a bedded-salt formation. Site investigations began in the early 1970s and are culminating with the completion of the Site and Preliminary Design Validation (SPDV) program in 1983 in which two shafts and several thousand feet of underground drifts are being constructed. The underground facility will be used for in situ tests and demonstrations that address technical issues associated with the disposal of transuranic and defense high-level wastes (DHLW) in bedded salt. These tests are based on several years of laboratory tests, field tests in mines, and analytical modeling studies. They primarily address repository development in bedded salt, including thermal-structural interactions plugging and sealing, and facility operations; and waste package interactions, including the effects of the waste on local rock salt and the evaluation of waste package materials. In situ testing began in the WIPP with the initiation of the SPDV program in 1981. In 1983, a major series of tests will begin to investigate the response of the rock salt without the use of any radioactivity

Test Results and Comparison of Triaxial Strength Testing of Waste Isolation Pilot Plant Clean Salt

Energy Technology Data Exchange (ETDEWEB)

Buchholz, Stuart A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-12-01

This memorandum documents laboratory thermomechanical triaxial strength testing of Waste Isolation Pilot Plant (WIPP) clean salt. The limited study completed independent, adjunct laboratory tests in the United States to assist in validating similar testing results being provided by the German facilities. The testing protocol consisted of completing confined triaxial, constant strain rate strength tests of intact WIPP clean salt at temperatures of 25°C and 100°C and at multiple confining pressures. The stratigraphy at WIPP also includes salt that has been labeled “argillaceous.” The much larger test matrix conducted in Germany included both the so-called clean and argillaceous salts. When combined, the total database of laboratory results will be used to develop input parameters for models, assess adequacy of existing models, and predict material behavior. These laboratory studies are also consistent with the goals of the international salt repository research program. The goal of this study was to complete a subset of a test matrix on clean salt from the WIPP undertaken by German research groups. The work was performed at RESPEC in Rapid City, South Dakota. A rigorous Quality Assurance protocol was applied, such that corroboration provides the potential of qualifying all of the test data gathered by German research groups.

Development and validation of a predictive technology for creep closure of underground rooms in salt

International Nuclear Information System (INIS)

Munson, D.E.; DeVries, K.L.

1991-07-01

Because of the concern for public health and safety, when compared to normal engineering practice, radioactive waste repositories have quite unusual requirements governing performance assessment. In part, performance assessment requires prediction of time-dependent or creep response of the repository hundreds to thousands of years into the future. In salt, one specific need is to predict, with confidence, the time at which the repository rooms creep closed sufficiently to encapsulate the waste and seal the repository. Thus, a major task of the Waste Isolation Pilot Plant (WIPP) Program is to develop and validate this predictive technology to calculate creep of repository rooms in the bedded salt deposits of Southeastern New Mexico. 19 refs., 15 figs., 2 tabs

Roadmap for disposal of Electrorefiner Salt as Transuranic Waste.

Energy Technology Data Exchange (ETDEWEB)

Rechard, Robert P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Trone, Janis R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kalinina, Elena Arkadievna [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wang, Yifeng [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hadgu, Teklu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sanchez, Lawrence C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-12-01

The experimental breeder reactor (EBR-II) used fuel with a layer of sodium surrounding the uranium-zirconium fuel to improve heat transfer. Disposing of EBR-II fuel in a geologic repository without treatment is not prudent because of the potentially energetic reaction of the sodium with water. In 2000, the US Department of Energy (DOE) decided to treat the sodium-bonded fuel with an electrorefiner (ER), which produces metallic uranium product, a metallic waste, mostly from the cladding, and the salt waste in the ER, which contains most of the actinides and fission products. Two waste forms were proposed for disposal in a mined repository; the metallic waste, which was to be cast into ingots, and the ER salt waste, which was to be further treated to produce a ceramic waste form. However, alternative disposal pathways for metallic and salt waste streams may reduce the complexity. For example, performance assessments show that geologic repositories can easily accommodate the ER salt waste without treating it to form a ceramic waste form. Because EBR-II was used for atomic energy defense activities, the treated waste likely meets the definition of transuranic waste. Hence, disposal at the Waste Isolation Pilot Plant (WIPP) in southern New Mexico, may be feasible. This report reviews the direct disposal pathway for ER salt waste and describes eleven tasks necessary for implementing disposal at WIPP, provided space is available, DOE decides to use this alternative disposal pathway in an updated environmental impact statement, and the State of New Mexico grants permission.

Basic data report for drillhole WIPP 11 (Waste Isolation Pilot Plant - WIPP)

International Nuclear Information System (INIS)

1982-02-01

Seismic reflection data from petroleum industry sources showed anomalous reflectors in the Castile Formation over a small area about 3 miles north of the center of the Waste Isolation Pilot Plant (WIPP) site. Additional corroborative seismic reflection data were collected as part of WIPP investigations, and WIPP 11 was drilled to investigate the anomaly. WIPP 11 was drilled near the northwest corner of Section 9, T.22.S., R.31E. it penetrated, in descending order, sand dune deposits and the Gatuna Formation (29'), Santa Rosa Sandstone (132'), Dewey Lake Red Beds (502'), Rustler Formation (288'), Salado Formation (1379'), and most of the Castile Formation (1240'). Beds within the lower part of the Salado, and the upper anhydrite of the Castile, are thinner than normal; these beds are displaced upward structurally by the upper Castile halite which is highly thickened (about 968'). The lowest halite is thin (51') and the basal anhydrite was not completely penetrated. Subsequent seismic and borehole data has shown WIPP 11 to be in a structural complex now identified as the disturbed zone. The WIPP is a demonstration facility for the disposal of transuranic (TRU) waste from defense programs. The WIPP will also provide a research facility to investigate the interactions between bedded salt and high level waste, though there are no plans at this time to dispose of high level waste or spent fuel at WIPP

Salt Repository Project: Data report on corrosion results obtained from excess-salt corrosion test Matrix 1

International Nuclear Information System (INIS)

Haberman, J.H.; Westerman, R.E.

1987-05-01

The test discussed in this data report was directed at determining the response of the reference A216 grade WCA steel when it is exposed to anoxic excess-salt conditions at 150 0 C. The environment used in the test was intended to duplicate the intrusion brine scenario (i.e., the formation of brine by the intrusion of water from an outside source into the repository, with the formation of brine through dissolution of salt from the repository horizon). The salt-brine environment used in the test therefore reflected the expected gross salt composition of the repository horizon

Alternative methods of salt disposal at the seven salt sites for a nuclear waste repository

International Nuclear Information System (INIS)

1987-02-01

This study discusses the various alternative salt management techniques for the disposal of excess mined salt at seven potentially acceptable nuclear waste repository sites: Deaf Smith and Swisher Counties, Texas; Richton and Cypress Creek Domes, Mississippi; Vacherie Dome, Louisiana; and Davis and Lavender Canyons, Utah. Because the repository development involves the underground excavation of corridors and waste emplacement rooms, in either bedded or domed salt formations, excess salt will be mined and must be disposed of offsite. The salt disposal alternatives examined for all the sites include commercial use, ocean disposal, deep well injection, landfill disposal, and underground mine disposal. These alternatives (and other site-specific disposal methods) are reviewed, using estimated amounts of excavated, backfilled, and excess salt. Methods of transporting the excess salt are discussed, along with possible impacts of each disposal method and potential regulatory requirements. A preferred method of disposal is recommended for each potentially acceptable repository site. 14 refs., 5 tabs

WIPP R and D in situ test program

International Nuclear Information System (INIS)

Tyler, L.D.

1987-01-01

The Waste Isolation Pilot Plant (WIPP) is a Department of Energy (DOE) RandD Facility for the purpose of developing the technology needed for the safe disposal of the United States' defense-related radioactive waste. The in situ test program focus is to provide the models and data to demonstrate the facility performance for isolation of waste at WIPP. The program is defined for the WIPP sealing system, thermal-structural interactions and waste package performance. A number of integrated large-scale underground tests have been operational since 1983 and are ongoing. The tests address the issues of both systems design and long-term isolation performance of the WIPP repository

Pressure-driven brine migration in a salt repository

International Nuclear Information System (INIS)

Hwang, Y.; Chambre, P.L.; Pigford, T.H.; Lee, W.W.L.

1989-01-01

The traditional view is that salt is the ideal rock for isolation of nuclear waste because it is ''dry'' and probably ''impermeable.'' The existence of salt through geologic time is prima facie evidence of such properties. Experiments and experience at potential salt sites for geologic repositories have indicated that while porosity and permeability of salt are low, the salt may be saturated with brine. If this hypothesis is correct, then it is possible to have brine flow due to pressure differences within the salt. If there is pressure-driven brine migration in salt repositories then it is paramount to know the magnitude of such flow because inward brine flow would affect the corrosion rate of nuclear waste containers and outward brine flow might affect radionuclide transport rates. Brine exists in natural salt as inclusions in salt crystals and in grain boundaries. Brine inclusions in crystals move to nearby grain boundaries when subjected to a temperature gradient, because of temperature-dependent solubility of salt. Brine in grain boundaries moves under the influence of a pressure gradient. When salt is mined to create a waste repository, brine from grain boundaries will migrate into the rooms, tunnels and boreholes because these cavities are at atmospheric pressure. After a heat-emitting waste package is emplaced and backfilled, the heat will impose a temperature gradient in the surrounding salt that will cause inclusions in the nearby salt to migrate to grain boundaries within a few years, adding to the brine that was already present in the grain boundaries. The formulation of brine movement with salt as a thermoelastic porous medium, in the context of the continuum theory of mixtures, has been described. In this report we show the mathematical details and discuss the results predicted by this analysis

Evaluation of proposed panel closure modifications at WIPP

Energy Technology Data Exchange (ETDEWEB)

Allen, Lawrence E.; Silva, Matthew K.; Channell, James K.; Abel, John F.; Morgan, Dudley R.

2001-12-31

A key component in the design of the WIPP repository is the installation of concrete structures as panel seals in the intake and exhaust drifts after a panel has been filled with waste containers. As noted in the EPA final rule, the panel seal closure system is intended to block brine flow between the waste panels at the WIPP. On April 17, 2001, the DOE proposed seven modifications to the EPA concerning the design of the panel closure system. EPA approval of these modifications is necessary since the details of the panel design are specified in EPA’s final rule as a condition for WIPP certification. However, the EPA has not determined whether a rulemaking would be required for these proposed design modifications. On September 4, 2001, the DOE withdrew the request, noting that it would be resubmitted on a future date. The Environmental Evaluation Group (EEG) contracted with two engineers, Dr. John Abel and Dr. Rusty Morgan, to evaluate the proposed modifications. The EEG has accepted the conclusions and recommendations from these two experts: 1) replacement of Salado Mass Concrete with a generic salt-based concrete; 2) replacement of the explosion wall with a construction wall; 3) replacement of freshwater grouting with salt-based grouting; 4) option to allow surface or underground mixing; and 5) option to allow up to one year for completion of closure. The proposed modification to allow local carbonate river rock as aggregate is acceptable pending demonstration that no problems will exist in the resulting concrete. The proposed modification to give the contractor discretion in removal of steel forms is not supported. Instead, several recommendations are made to specifically reduce the number of forms left, thereby reducing potential migration pathways.

Statistical methods for mechanistic model validation: Salt Repository Project

International Nuclear Information System (INIS)

Eggett, D.L.

1988-07-01

As part of the Department of Energy's Salt Repository Program, Pacific Northwest Laboratory (PNL) is studying the emplacement of nuclear waste containers in a salt repository. One objective of the SRP program is to develop an overall waste package component model which adequately describes such phenomena as container corrosion, waste form leaching, spent fuel degradation, etc., which are possible in the salt repository environment. The form of this model will be proposed, based on scientific principles and relevant salt repository conditions with supporting data. The model will be used to predict the future characteristics of the near field environment. This involves several different submodels such as the amount of time it takes a brine solution to contact a canister in the repository, how long it takes a canister to corrode and expose its contents to the brine, the leach rate of the contents of the canister, etc. These submodels are often tested in a laboratory and should be statistically validated (in this context, validate means to demonstrate that the model adequately describes the data) before they can be incorporated into the waste package component model. This report describes statistical methods for validating these models. 13 refs., 1 fig., 3 tabs

Radioactive waste disposal: Waste Isolation Pilot Plants (WIPP). March 1978-November 1989 (Citations from the NTIS data base). Report for Mar 78-Nov 89

International Nuclear Information System (INIS)

1990-01-01

This bibliography contains citations concerning the Waste Isolation Pilot Plant (WIPP), a geologic repository located in New Mexico for transuranic wastes generated by the U.S. Government. Articles follow the development of the program from initial site selection and characterization through construction and testing, along with research programs on environmental impacts, structural design, and radionuclide landfill gases. Existing plants and facilities, pilot plants, migration, rock mechanics, economics, regulations, and transport of wastes to the site are also included. The Salt Repository Project and the Crystalline Repository Project are referenced in related published bibliographies. (Contains 184 citations fully indexed and including a title list.)

Salt repository design approach

International Nuclear Information System (INIS)

Matthews, S.C.

1983-01-01

This paper presents a summary discussion of the approaches that have been and will be taken in design of repository facilities for use with disposal of radioactive wastes in salt formations. Since specific sites have yet to be identified, the discussion is at a general level, supplemented with illustrative examples where appropriate. 5 references, 1 figure

Implications of the presence of petroleum resources on the integrity of the WIPP

International Nuclear Information System (INIS)

Silva, M.K.

1994-06-01

The Waste Isolation Pilot Plant (WIPP) is a facility of the US Department of Energy (DOE), designed and constructed for the permanent disposal of transuranic (TRU) defense waste. The WIPP is surrounded by reserves of potash, crude oil, and natural gas. These are attractive targets for exploratory drilling which could disrupt the integrity of the transuranic waste repository. The performance assessment calculations published to date have identified future drilling for oil and gas reserves as an event that may disrupt the repository and may release radionuclides in excess of the standards. Therefore, the probability of inadvertent human intrusion into the repository by drilling and its impact on the integrity of the repository must be carefully assessed. This report evaluates: (1) the studies funded by the DOE to examine the crude oil potential in the immediate vicinity of the WIPP; (2) the use of an elicitation exercise to predict future drilling rates for use in the calculation of the repository performance; and (3) the observed limitations of institutional controls. This report identifies the following issues that remain to be resolved: (1) the limited performance of blowout preventers after drilling into high pressure zones immediately adjacent to the WIPP Site Boundary; (2) reported problems with waterflooding operations in southeastern New Mexico; (3) reported water level rises in several wells completed in the Rustler Formation, south of the WIPP Site, possibly due to oil and gas wells or leaking injection wells; and (4) reports of inadequate well abandonment practices on BLM leases and the continued absence of enforceable regulations

Basic data report for deepening of drillhole WIPP 13 (Waste Isolation Pilot Plant-WIPP)

International Nuclear Information System (INIS)

1982-10-01

WIPP 13 is a borehole drilled in eastern Eddy County, New Mexico, in section 17, T22S,R31E, in order to investigate a subsurface seismic disturbed zone. The first 1035 ft of the borehole were drilled in July and August 1978. The deepening of WIPP 13 was performed in 1979 between August and October. This report documents the deepening of WIPP 13 to 3861.8 ft. Only rocks of the Permian, Salado and Castile Formations were penetrated in the deepening. Cores were obtained for some portions of the hole and cuttings were collected from some of the sections which were not cored (see Table 1). A suite of geophysical logs was run to provide information on lithology, structure and geochemistry. The WIPP is a demonstration facility for the disposal of transuranic (TRU) waste from defense programs. The WIPP will also provide a research facility to investigate the interactions between bedded salt and high level wastes

Source term estimation and the isotopic ratio of radioactive material released from the WIPP repository in New Mexico, USA

International Nuclear Information System (INIS)

Thakur, P.

2016-01-01

lifted its lid to allow release of waste into the underground air. - Highlights: • February 14, 2014 radiation release from the Nation's only TRU waste repository is discussed. • Environmental monitoring results in the vicinity of the WIPP site are presented. • Source term estimation of the radioactive material released is assessed. • The isotopic ratio of the radioactive material release from the WIPP is discussed.

The Brine Sampling and Evaluation Program (PSEP) at WIPP

International Nuclear Information System (INIS)

Deal, D.E.; Roggenthen, W.M.

1989-01-01

The Permian salt beds of the WIPP facility are virtually dry. The amount of water present in the rocks exposed in the excavations that is free to migrate under pressure gradients was estimated by heating salt samples to 95 degrees C and measuring weight loss. Clear balite contains about 0.22 weight percent water and the more argillaceous units average about 0.75 percent. Measurements made since 1984 as part of the Brine Sampling and Evaluation Program (BSEP) indicate that small amounts of this brine can migrate into the excavations and does accumulate in the underground environment. Brine seepage into drillholes monitored since thy were drilled show that brine seepage decreases with time and that many have dried up entirely. Weeping of brine from the walls of the repository excavations also decreases after two or more years. Chemical analyses of brines shows that they are sodium-chloride saturated and magnesium-rich

Basic data report for drillhole WIPP 12 (Waste Isolation Pilot Plant-WIPP)

International Nuclear Information System (INIS)

1982-10-01

WIPP 12 is a borehole drilled in eastern Eddy County, New Mexico, to investigate the stratigraphy, structure and lithology in the WIPP area. WIPP 12 was drilled in section 17, T22S,R31E, between November 9 and December 7, 1978. The hole was drilled to a depth of 2785.8 ft. It encountered from top to bottom, 16.2 ft of sand, 3 ft of Mescalero Caliche and 9.6 ft of the Gatuna Formation, all of Quaternary age; 138.2 ft of the Triassic Santa Rosa Formation, 483 ft of the Dewey Lake Red Beds, 326 ft of the Rustler Formation, 1771.5 ft of the Salado Formation, and 48.3 ft of the Castile Formation, all of Permian age. Cores or cuttings were obtained for the entire hole. A suite of geophysical logs, including neutron gamma and density curves, was run to the full depth of WIPP 12. The borehole demonstrated that the elevation of the top of the Castile is about 160' above the same horizon in ERDA 9. The WIPP is a demonstration facility for the disposal of transuranic (TRU) waste from defense programs. The WIPP will also provide a research facility to investigate the interactions between bedded salt and high level wastes

Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Chapter E, Appendix E1, Chapter L, Appendix L1: Volume 12, Revision 3

Energy Technology Data Exchange (ETDEWEB)

1993-01-01

The Waste Isolation Pilot Plant (WIPP) Project was authorized by the US Department of Energy 5 (DOE) National Security and Military Applications of the Nuclear Energy Authorization Act of 1980 (Public Law 96-164). Its legislative mandate is to provide a research and development facility to demonstrate the safe disposal of radioactive waste resulting from national defense programs and activities. To fulfill this mandate, the WIPP facility has been designed to perform scientific investigations of the behavior of bedded salt as a repository medium and the interactions between the soft and radioactive wastes. In 1991, DOE proposed to initiate a experimental Test Phase designed to demonstrate the performance of the repository. The Test Phase activities involve experiments using transuranic (TRU) waste typical of the waste planned for future disposal at the WIPP facility. Much of this TRU waste is co-contaminated with chemical constituents which are defined as hazardous under HWMR-7, Pt. II, sec. 261. This waste is TRU mixed waste and is the subject of this application. Because geologic repositories, such as the WIPP facility, are defined under the Resource Conservation and Recovery Act (RCRA) as land disposal facilities, the groundwater monitoring requirements of HWMR-7, PLV, Subpart X, must be addressed. HWMR-7, Pt. V, Subpart X, must be addressed. This appendix demonstrates that groundwater monitoring is not needed in order to demonstrate compliance with the performance standards; therefore, HWMR-7, Pt.V, Subpart F, will not apply to the WIPP facility.

Rationale for the H-19 and H-11 tracer tests at the WIPP site

International Nuclear Information System (INIS)

Beauheim, R.L.; Meigs, L.C.; Davies, P.B.

1996-01-01

The Waste Isolation Pilot Plant (WIPP) is a repository for transuranic wastes constructed in bedded Permian-age halite in the Delaware Basin, a sedimentary basin in southeastern New Mexico, USA. A drilling scenario has been identified during performance assessment (PA) that could lead to the release of radionuclides to the Culebra Dolomite Member of the Rustler Formation, the most transmissive water-saturated unit above the repository horizon. Were this to occur, the radionuclides would need to be largely contained within the Culebra (or neighboring strata) within the WIPP-site boundary through the period lasting for 10,000 years after repository closure for WIPP to remain in compliance with applicable regulations on allowable releases. Thus, processes affecting transport of radionuclides within the Culebra are of importance to PA

Hydraulic Characterization Activities in Support of the Shaft-Seals Fluid-Flow Modeling Integration into the WIPP EPA Compliance Certification Application

International Nuclear Information System (INIS)

Knowles, M.K.; Hurtado, L.D.; Dale, Tim

1997-12-01

The Waste Isolation Pilot Plant (WIPP) is a planned geologic repository for permanent disposal of transuranic waste generated by the U.S. Department of Energy. Disposal regions consist of panels and drifts mined from the bedded salt of the Salado Formation at a depth of approximately 650 m below the surface. This lithology is part of the 225 million year old Delaware Basin, and is geographically located in southeastern New Mexico. Four shafts service the facility needs for air intake, exhaust, waste handling, and salt handling. As the science advisor for the project, Sandia National Laboratories developed the WIPP shaft sealing system design. This design is a fundamental component of the application process for facility licensing, and has been found acceptable by stakeholders and regulatory agencies. The seal system design is founded on results obtained from laboratory and field experiments, numerical modeling, and engineering judgment. This paper describes a field test program to characterize the fluid flow properties in the WIPP shafts at representative seal locations. This work was conducted by Duke Engineering and Services under contract to Sandia National Laboratories in support of the seal system design

WIPP: construction and progress on a successful nuclear waste repository

International Nuclear Information System (INIS)

Cooper, W.R.; Sankey, C.A.

1985-01-01

The Department of Energy is constructing the Waste Isolation Pilot Plant (WIPP) in Southeastern New Mexico. The facility will retrievably store transuranic waste from defense activities of the United States and conduct experiments with Defense high-level waste which will be retrieved at the end of the experiments. This paper describes the progress and the present status of activities at WIPP. 4 refs

Assessment of crushed salt consolidation and fracture healing processes in a nuclear waste repository in salt

International Nuclear Information System (INIS)

1984-11-01

For a nuclear waste repository in salt, two aspects of salt behavior are expected to contribute to favorable conditions for waste isolation. First, consolidation of crushed salt backfill due to creep closure of the underground openings may result in a backfill barrier with low permeability. Second, fractures created in the salt by excavation may heal under the influence of stress and temperature following sealing. This report reviews the status of knowledge regarding crushed salt consolidation and fracture healing, provides analyses which predict the rates at which the processes will occur under repository conditions, and develops requirements for future study. Analyses of the rate at which crushed salt will consolidate are found to be uncertain because of unexplained wide variation in the creep properties of crushed salt obtained from laboratory testing, and because of uncertainties in predictions of long term closure rates of openings in salt. This uncertainty could be resolved to a large degree by additional laboratory testing of crushed salt. Similarly, additional testing of fracture healing processes is required to confirm that healing will be effective under repository conditions. Extensive references, 27 figures, 5 tables

Salt Repository Project shaft design guide: Revision 0

International Nuclear Information System (INIS)

1987-12-01

The Salt Repository Project (SRP) Shaft Design Guide (SDG) and the accompanying SRP Input to Seismic Design define the basic approach for developing appropriate shaft designs for a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. The SDG is based on current mining industry standards and practices enhanced to meet the special needs of an underground nuclear waste repository. It provides a common approach for design of both the exploratory and repository shafts. The SDG defines shaft lining and material concepts and presents methods for calculating the loads and displacements that will be imposed on lining structures. It also presents the methodology and formulae for sizing lining components. The SDG directs the shaft designer to sources of geoscience and seismic design data for the Deaf Smith County, Texas repository site. In addition, the SDG describes methods for confirming shaft lining design by means of computer analysis, and it discusses performance monitoring needs that must be considered in the design. 113 refs., 18 figs., 14 tabs

Basic data report for drillhole WIPP 32 (Waste Isolation Pilot Plant - WIPP)

International Nuclear Information System (INIS)

1980-11-01

WIPP 32 is an exploratory borehole drilled to examine the subsurface at a small topographic high in Nash Draw. The borehole is located in east-central Eddy County, New Mexico, in NE 1/4 SE 1/4 Sec. 33, T.22S., R.29E. and was drilled in August, 1979. The hole was drilled to a depth of 390 feet, and encountered, from top to bottom, the Rustler Formation (166') and the upper Salado Formation (224'). Core was taken from 4 to 353 feet. Geophysical logs were run the full length of the hole to measure formation properties. The WIPP is to demonstrate (through limited operations) disposal technology for transuranic defense wastes. The WIPP will also provide facilities to research interactions between high-level waste and salt

Sealing considerations for repository shafts in bedded and dome salt

International Nuclear Information System (INIS)

1981-12-01

The report reviews the geologic and hydrologic data base for penetration seal designs referenced to the Los Medanos bedded salt site in New Mexico and to four candidate salt domes in the Gulf Interior. Experience with existing shafts highlights the importance, for shaft decommissioning as well as operation, of achieving an adequate seal at and immediately below the top of salt. Possible construction procedures for repository shafts are reviewed, noting advantages and disadvantages with respect to repository sealing. At this stage, there does not appear to be a clear preference for excavation by drill and blast or by drilling. If conventional drill and blast methods are used, it may be necessary to grout in permeable zones above the salt. An important consideration with respect to sealing is that grouting operations (or freezing should it be used) should not establish connections between the top of salt and water-bearing zones higher in the stratigraphic section. Generally, it is concluded that Los Medanos and the dome salt sites are favorable candidate repository sites from the point of view of sealing

The Herfa-Neurode hazardous waste repository in bedded salt as an operating model for safe mixed waste disposal

International Nuclear Information System (INIS)

Rempe, N.T.

1991-01-01

For 18 years, The Herfa-Neurode underground repository has demonstrated the environmentally sound disposal of hazardous waste in a former potash mine. Its principal characteristics make it an excellent analogue to the Waste Isolation Pilot Plant (WIPP). The Environmental Protection Agency has ruled in its first conditional no-migration determination that is reasonably certain that no hazardous constituents of the mixed waste, destined for the WIPP during its test phase, will migrate from the site for up to ten years. Knowledge of and reference to the Herfa-Neurode operating model may substantially improve the no-migration variance petition for the WIPP's disposal phase and thereby expedite its approval. 2 refs., 1 fig., 1 tab

Structural evaluation of WIPP disposal room raised to clay seam G

International Nuclear Information System (INIS)

Park, Byoung Yoon; Holland, John F.

2007-01-01

An error was discovered in the ALGEBBRA script used to calculate the disturbed rock zone around the disposal room and the shear failure zone in the anhydrite layers in the original version. To correct the error, a memorandum of correction was submitted according to the Waste Isolation Pilot Plant (WIPP) Quality Assurance program. The recommended course of action was to correct the error, to repeat the post-process, and to rewrite Section 7.4, 7.5, 8, and Appendix B in the original report. The sections and appendix revised by the post-process using the corrected ALGEBRA scripts are provided in this revision. The original report summarizes a series of structural calculations that examine effects of raising the WIPP repository horizon from the original design level upward 2.43 meters. Calculations were then repeated for grid changes appropriate for the new horizon raised to Clay Seam G. Results are presented in three main areas: (1) Disposal room porosity, (2) Disturbed rock zone characteristics, and (3) Anhydrite marker bed failure. No change to the porosity surface for the compliance re-certification application is necessary to account for raising the repository horizon, because the new porosity surface is essentially identical. The disturbed rock zone evolution and devolution are charted in terms of a stress invariant criterion over the regulatory period. This model shows that the propagation of the DRZ into the surrounding rock salt does not penetrate through MB 139 in the case of both the original horizon and the raised room. Damaged salt would be expected to heal in nominally 150 years. The shear failure does not occur in either the upper or lower anhydrite layers at the moment of excavation, but appears above and below the middle of the pillar one day after the excavation. The damaged anhydrite is not expected to heal as the salt in the DRZ is expected to

Second benchmark problem for WIPP structural computations

International Nuclear Information System (INIS)

Krieg, R.D.; Morgan, H.S.; Hunter, T.O.

1980-12-01

This report describes the second benchmark problem for comparison of the structural codes used in the WIPP project. The first benchmark problem consisted of heated and unheated drifts at a depth of 790 m, whereas this problem considers a shallower level (650 m) more typical of the repository horizon. But more important, the first problem considered a homogeneous salt configuration, whereas this problem considers a configuration with 27 distinct geologic layers, including 10 clay layers - 4 of which are to be modeled as possible slip planes. The inclusion of layering introduces complications in structural and thermal calculations that were not present in the first benchmark problem. These additional complications will be handled differently by the various codes used to compute drift closure rates. This second benchmark problem will assess these codes by evaluating the treatment of these complications

Preliminary analyses of scenarios for potential human interference for repositories in three salt formations

International Nuclear Information System (INIS)

1985-10-01

Preliminary analyses of scenarios for human interference with the performance of a radioactive waste repository in a deep salt formation are presented. The following scenarios are analyzed: (1) the U-Tube Connection Scenario involving multiple connections between the repository and the overlying aquifer system; (2) the Single Borehole Intrusion Scenario involving penetration of the repository by an exploratory borehole that simultaneously connects the repository with overlying and underlying aquifers; and (3) the Pressure Release Scenario involving inflow of water to saturate any void space in the repository prior to creep closure with subsequent release under near lithostatic pressures following creep closure. The methodology to evaluate repository performance in these scenarios is described and this methodology is applied to reference systems in three candidate formations: bedded salt in the Palo Duro Basin, Texas; bedded salt in the Paradox Basin, Utah; and the Richton Salt Dome, Mississippi, of the Gulf Coast Salt Dome Basin

Systems analysis, long-term radionuclide transport, and dose assessments, Waste Isolation Pilot Plant (WIPP), southeastern New Mexico, September 1989

International Nuclear Information System (INIS)

Lappin, A.R.; Hunter, R.L.; Davies, P.B.; Borns, D.J.; Reeves, M.; Pickens, J.; Iuzzolino, H.J.

1990-12-01

This study supports the Waste Isolation Pilot Plant (WIPP) Final Supplemental Environmental Impact Statement and has two main objectives. First, it describes current ideas about the characteristics and potential impacts of the disturbed-rock zone (DRZ) known to develop with time around excavations at the WIPP horizon. Second, it presents new calculations of radionuclide migration within and from the WIPP repository for steady-state undisturbed conditions and for two cases that consider human intrusion into the repository. At the WIPP, the presence of a DRZ has been confirmed by geophysical studies, gas-flow tests, and direct observations. The DRZ will allow gas or brine from waste-emplacement panels to bypass panel seals and flow into adjacent portions of the underground workings unless preventive measures are taken. Revised calculations of the undisturbed performance of the repository indicate that no radionuclides will be released into the Culebra Dolomite within the regulatory period of 10,000 years. The human-intrusion calculations included here assume a connection between the WIPP repository, an occurrence of pressurized brine within the underlying Castile Formation, and the overlying Culebra Dolomite. 61 refs., 40 figs., 16 tabs

Site evaluation for the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Hill, L.R.

1979-01-01

Preliminary site selection activities for the WIPP are complete now; these consisted primarily of national and regional studies over the past fifteen years, and resulted in selection of the WIPP study area for geological characterization. The work of geological characterization should be considered to have begun with the drilling of ERDA 9 at the center of the WIPP study area and the initiation of seismic reflection work on the site. That geological characterization, which is primarily oriented to provide specific data concerning the present geology of the site, was virtually complete in December, 1978, when the Geological Characterization Report was submitted to the Department of Energy; much basic information has been gathered indicating no major technical problems with the site as it is now understood. Studies of long-term processes which might affect a repository or have an effect on safety analyses will now be the major geotechnical activity for the WIPP site evaluation team, some of these activities are already underway. These studies will deal with the age of significant features and the rates and processes which produce those features. The information so gained will be useful in increasing the confidence in evaluation of the safety of a repository

Inelastic thermomechanical analysis of a generic bedded salt repository. Technical report

International Nuclear Information System (INIS)

Callahan, G.D.

1981-02-01

The thermomechanical response of a generic bedded salt stratigraphy accommodating a spent fuel repository at a depth of 610 m in a relatively thin salt bed is investigated. The thermal density at waste emplacement was assumed to be 14.8 W/m 2 (60 kW/acre). Emphasis is placed on rock mass properties, elastic and thermal anisotropy (within the shale layers), and structural discontinuities defined as preferred planes of weakness. No attempt is made to include long-term effects of geologic actions, chemical processes, groundwater, and pore water. The rock mass is assumed to contain pre-existing joints and fissures. Therefore, the stratigraphy encompassing the repository (excluding the salt beds) was assumed to be incapable of supporting tensile stresses. Thermoelastic/plastic response of the various sedimentary formations is considered for the intact rock mass and several orientations of preferred planes of weakness. The results indicate an intact buffer zone between the upper strata and the repository approximately 450 m thick, which underwent no irreversible deformation. Contained plastic deformation was observed below the repository along preferred planes of weakness dipping at 60 and 120 degrees. The structural response of this generic bedded salt stratigraphy does not appear to be detrimental to the overall waste containment in the repository

Basic data report for drillhole WIPP 19 (Waste Isolation Pilot Plant-WIPP)

International Nuclear Information System (INIS)

1980-03-01

WIPP 19 is an exploratory borehole whose objective was to determine the nature of the near-surface formations after seismic information indicated a possible fault. The borehole is located in section 20, T.22S., R.31E., in eastern Eddy County, New Mexico, and was drilled between April 6 and May 4, 1978. The hole was drilled to a depth of 1038.2 feet and encountered, from top to bottom, surficial Holocene deposits (7', including artificial fill for drill pad), the Mescalero caliche (7'), the Santa Rosa Sandstone (82'), the Dewey Lake Red Beds (494'), the Rustler Formation (315'), and the upper portion of the Salado Formation (143'). Cuttings were collected at 10-foot intervals. A suite of geophysical logs was run to measure acoustic velocities, density, and radioactivity. On the basis of comparison with other geologic sections drilled in the area, the WIPP 19 section is a normal stratigraphic sequence and it does not show structural disruption. The WIPP is to demonstrate (through limited operations) disposal technology for transuranic defense wastes. The WIPP will also provide facilities to research interactions between high-level waste and salt

Basic data report for drillhole WIPP 21 (Waste Isolation Pilot Plant - WIPP)

International Nuclear Information System (INIS)

1980-03-01

WIPP 21 is an exploratory borehole whose objective is to determine the nature of the near-surface formations after seismic information indicated a possible fault. The borehole is located in section 20, T.22S., R.31E., in eastern Eddy County, New Mexico, and was drilled between May 24 and 26, 1978. The hole was drilled to a depth of 1046 feet and encountered, from top to bottom, surficial Holocene deposits (6', including artificial fill for drill pad), the Mescalero caliche (6'), the Santa Rosa Sandstone (34'), the Dewey Lake Red Beds (487'), the Rustler Formation (308'), and the upper portion of the Salado Formation (178'). Cuttings were collected at 10-foot intervals. A suite of goephysical logs was run to measure acoustic velocities, density, and radioactivity. On the basis of comparison with other geologic sections drilled in the area, the WIPP 21 section is a normal stratigraphic sequence and it does not show structural disruption. The WIPP is to demonstrate (through limited operations) disposal technology for transuranic defense wastes. The WIPP will also provide facilities to research interactions between high-level waste and salt

Basic data report for drillhole WIPP 18 (Waste Isolation Pilot Plant - WIPP)

International Nuclear Information System (INIS)

1980-03-01

WIPP 18 is an exploratory borehole whose objective is to determine the nature of the near-surface formations after seismic information indicated a possible fault. The borehole is located in section 20, T.22S., R.31E., in eastern Eddy County, New Mexico, and was drilled between March 14 and 30, 1978. The hole was drilled to a depth of 1060 feet and encountered, from top to bottom, surficial Holocene deposits (5', including artificial fill for drill pad), the Mescalero caliche (4'), the Santa Rosa Sandstone (129'), the Dewey Lake Red Beds (475'), the Rustler Formation (315'), and the upper portion of the Salado Formation (132'). Cuttings were collected at 10-foot intervals. A suite of geophysical logs was run to measure acoustic velocities, density, and radioactivity. On the basis of comparison with other geologic sections drilled in the area, the WIPP 18 section is a normal stratigraphic sequence and it does not show structural disruption. The WIPP is to demonstrate (through limited operations) disposal technology for transuranic defense wastes. The WIPP will also provide facilities to research interactions between high-level waste and salt

Basic data report for Drillhole WIPP 22 (Waste Isolation Pilot Plant, WIPP)

International Nuclear Information System (INIS)

1980-03-01

WIPP 22 is an exploratory borehole whose objective is to determine the nature of the near-surface formations after seismic information indicated a possible fault. The borehole is located in section 20, T.22S., R.31E., in eastern Eddy County, New Mexico, and was drilled between March 14 and 30, 1978. The hole was drilled to a depth of 1448 feet and encountered, from top to bottom, surficial Holocene deposits (6', including artificial fill for drill pad), the Mescalero caliche (7'), the Santa Rosa Sandstone (68'), the Dewey Lake Red Beds (492'), the Rustler Formation (311'), and the upper portion of the Salado Formation (565'). Cuttings were collected at 10-foot intervals. A suite of geophysical logs was run to measure acoustic velocities, density, and radioactivity. On the basis of comparison with other geologic sections drilled in the area, the WIPP 22 section is a normal stratigraphic sequence and it does not show structural disruption. The WIPP is to demonstrate (through limited operations) disposal technology for transuranic defense wastes. The WIPP will also provide facilities to research interactions between high-level waste and salt

Test Plan: WIPP bin-scale CH TRU waste tests

International Nuclear Information System (INIS)

Molecke, M.A.

1990-08-01

This WIPP Bin-Scale CH TRU Waste Test program described herein will provide relevant composition and kinetic rate data on gas generation and consumption resulting from TRU waste degradation, as impacted by synergistic interactions due to multiple degradation modes, waste form preparation, long-term repository environmental effects, engineered barrier materials, and, possibly, engineered modifications to be developed. Similar data on waste-brine leachate compositions and potentially hazardous volatile organic compounds released by the wastes will also be provided. The quantitative data output from these tests and associated technical expertise are required by the WIPP Performance Assessment (PA) program studies, and for the scientific benefit of the overall WIPP project. This Test Plan describes the necessary scientific and technical aspects, justifications, and rational for successfully initiating and conducting the WIPP Bin-Scale CH TRU Waste Test program. This Test Plan is the controlling scientific design definition and overall requirements document for this WIPP in situ test, as defined by Sandia National Laboratories (SNL), scientific advisor to the US Department of Energy, WIPP Project Office (DOE/WPO). 55 refs., 16 figs., 19 tabs

Experimental results on salt concrete for barrier elements made of salt concrete in a repository for radioactive waste in a salt mine

International Nuclear Information System (INIS)

Gutsch, Alex-W.; Preuss, Juergen; Mauke, Ralf

2012-01-01

The Bartensleben rock salt mine in Germany was used as a repository for low and intermediate level radioactive waste from 1971 to 1991 and from 1994 to 1998. The repository with an overall volume of about 6 million m 3 has to be closed. Salt concrete is used for the refill of the voids of the repository. The concrete mixtures contain crushed salt instead of natural aggregates as the void filling material should be as similar to the salt rock as possible. Very high requirements regarding low heat development and little or even no cracking during concrete hardening had to be fulfilled even for the barrier elements made from salt concrete which separate the radioactive waste from the environment. Requirements for the salt concrete were set up with regard to the fluidity of the fresh concrete during the hardening process and its durability. In the view of a comprehensive numerical calculations of the temperature development and thermal stresses in the massive salt concrete elements of the backfill of the voids, experimental results for material properties of the salt concrete are presented: mixture of the salt concrete, thermodynamic properties (adiabatic heat release, thermal dilatation, thermal conductivity and heat capacity), mechanical short term properties, creep (under tension, under compression), autogenous shrinkage

A coupled mechanical/hydrologic model for WIPP shaft seals

International Nuclear Information System (INIS)

Ehgartner, B.

1991-06-01

Effective sealing of the Waste Isolation Pilot Plant (WIPP) shafts will be required to isolate defense-generated transuranic wastes from the accessible environment. Shafts penetrate water-bearing hard rock formations before entering a massive creeping-salt formation (Salado) where the WIPP is located. Short and long-term seals are planned for the shafts. Short-term seals, a composite of concrete and bentonite, will primarily be located in the hard rock formations separating the water-bearing zones from the Salado Formation. These seals will limit water flow to the underlying long-term seals in the Salado. The long-term seals will consist of lengthly segments of initially unsaturated crushed salt. Creep closure of the shaft will consolidate unsaturated crushed salt, thereby reducing its permeability. However, water passing through the upper short-term seals and brine inherent to the salt host rock itself will eventually saturate the crushed salt and consolidation could be inhibited. Before saturating, portions of the crushed salt in the shafts are expected to consolidate to a permeability equivalent to the salt host rock, thereby effectively isolating the waste from the overlying water-bearing formations. A phenomenological model is developed for the coupled mechanical/hydrologic behavior of sealed WIPP shafts. The model couples creep closure of the shaft, crushed salt consolidation, and the associated reduction in permeability with Darcy's law for saturated fluid flow to predict the overall permeability of the shaft seal system with time. 17 refs., 6 figs., 1 tab

Salt Repository Project transportation program plan

International Nuclear Information System (INIS)

Fisher, R.L.; Greenberg, A.H.; Anderson, T.L.; Yates, K.R.

1987-01-01

The Salt Repository Project (SRP) has the responsibility to develop a comprehensive transportation program plan (TrPP) that treats the transportation of workers, supplies, and high-level radioactive waste to the site and the transportation of salt, low-level, and transuranic wastes from the site. The TrPP has developed a systematic approach to transportation which is directed towards satisfying statutes, regulations, and directives and is guided by a hierarchy of specific functional requirements, strategies, plans, and reports. The TrPP identifies and develops the planning process for transportation-related studies and provides guidance to staff in performing and documenting these activities. The TrPP also includes an explanation of the responsibilities of the organizational elements involved in these transportation studies. Several of the report chapters relate to identifying routes for transporting nuclear waste to the site. These include a chapter on identifying an access corridor for a new rail route leading to the site, identifying and evaluating emergency-response preparedness capabilities along candidate routes in the state, and identifying alternative routes from the state border, ports, or in-state reactors to the site. The TrPP also includes plans for identifying salt disposal routes and a discussion of repository/transportation interface requirements. 89 refs., 6 figs

In situ testing of titanium and mild steel nuclear waste containers at the WIPP site

International Nuclear Information System (INIS)

Molecke, M.A.

1990-01-01

An overview of the Waste Isolation Pilot Plant (WIPP) in situ tests on the corrosion of titanium and mild steel for high level waste containers is presented. The tests at Sandia have moved out of the laboratory into a test underground facility in order to evaluate the performance of the waste package material. The tests are being performed under both near-reference and accelerated salt repository conditions. Some containers are filled with high level waste glass (non-radioactive); others contain electric heaters. Backfill material is either bentonite/sand or crushed salt. In other tests metals and glasses are exposed directly to brine. The tests are designed to study the corrosion and metallurgy of the canister and overpack materials; the feasibility and performance of backfill materials; and near-field effects such as brine migration

WIPP waste package testing on simulated DHLW: emplacement

International Nuclear Information System (INIS)

Molecke, M.A.

1984-01-01

Several series of simulated (nonradioactive) defense high-level waste (DHLW) package tests have been emplaced in the WIPP, a research and development facility authorized to demonstrate the safe disposal of defense-related wastes. The primary purpose of these 3-to-7 year duration tests is to evaluate the in situ materials performance of waste package barriers (canisters, overpacks, backfills, and nonradioactive DHLW glass waste form) for possible future application to a licensed waste repository in salt. This paper describes all test materials, instrumentation, and emplacement and testing techniques, and discusses progress of the various tests. These tests are intended to provide information on materials behavior (i.e., corrosion, metallurgical and geochemical alterations, waste form durability, surface interactions, etc.), as well as comparison between several waste package designs, fabrications details, and actual costs. These experiments involve 18 full-size simulated DHLW packages (approximately 3.0 m x 0.6 m diameter) emplaced in vertical boreholes in the salt drift floor. Six of the test packages contain internal electrical heaters (470 W/canister), and were emplace under approximately reference DHLW repository conditions. Twelve other simulated DHLW packages were emplaced under accelerated-aging or overtest conditions, including the artificial introduction of brine, and a thermal loading approximately three to four times higher than reference. Eight of these 12 test packages contain 1500 W/canister electrical heaters; the other four are filled with DHLW glass. 9 refs., 1 fig

Repository seal materials performance for a SALT Repository Project 5-year code/model development plan: Draft

International Nuclear Information System (INIS)

1987-06-01

This document describes an integrated laboratory testing and model development effort for the seal system for a high-level nuclear waste repository in salt. The testing and modeling efforts are designed to determine seal material response in the repository environment, to provide models of seal system components for performance assessment, and to assist in the development of seal system designs. A code/model development and performance analysis program will be performed to predict the short- and long-term response of seal materials and seal components. The results from these analyses will be used to support the material testing activities on this contract and to support performance assessment activities that are conducted in other parts of the Salt Repository Project (SRP). 48 refs., 15 figs., 4 tabs

Evaluation of the proposed WIPP site in southeast New Mexico

International Nuclear Information System (INIS)

Weart, W.D.

1979-01-01

Five years of earth science characterization of the proposed Waste Isolation Pilot Plant (WIPP) site provide a high level of assurance that the area is satisfactory for development of a geologic repository. Ecological investigations and socioeconomic studies have indicated only relatively benign impacts will occur from construction, operation and long-term aspects of the repository

Evaluation of the proposed WIPP site in southeast New Mexico

Energy Technology Data Exchange (ETDEWEB)

Weart, W.D.

1979-01-01

Five years of earth science characterization of the proposed Waste Isolation Pilot Plant (WIPP) site provide a high level of assurance that the area is satisfactory for development of a geologic repository. Ecological investigations and socioeconomic studies have indicated only relatively benign impacts will occur from construction, operation and long-term aspects of the repository.

An evaluation of the proposed tests with radioactive waste at WIPP

International Nuclear Information System (INIS)

Chaturvedi, L.; Silva, M.

1992-01-01

This paper discusses the Waste Isolation Pilot Plant (WIPP) a planned repository for permanent disposal of transuranic (TRU) radiative waste that has resulted from the defense activities of the U.S. Government over the past 50 years. Only the waste that is currently stored in an easily retrievable mode at ten U.S. Department of Energy (DOE) laboratories around the country will be shipped to WIPP. The waste consists of various kinds of trash including paper, rubber, rags and metal that is contaminated with radionuclides with very long half-lives. The decision to dispose of the waste permanently will be made based on projections of the behavior of the waste and the repository of 10,000 years or more. DOE has proposed shipping a limited amount of waste to WIPP for a five year Test Phase to demonstrating compliance with the U.S. Environmental Protection Agency (EPA) Standard for long-term isolation

Computational implementation of the multi-mechanism deformation coupled fracture model for salt

International Nuclear Information System (INIS)

Koteras, J.R.; Munson, D.E.

1996-01-01

The Multi-Mechanism Deformation (M-D) model for creep in rock salt has been used in three-dimensional computations for the Waste Isolation Pilot Plant (WIPP), a potential waste, repository. These computational studies are relied upon to make key predictions about long-term behavior of the repository. Recently, the M-D model was extended to include creep-induced damage. The extended model, the Multi-Mechanism Deformation Coupled Fracture (MDCF) model, is considerably more complicated than the M-D model and required a different technology from that of the M-D model for a computational implementation

ERG [Engineering Review Group] review of the SRP [Salt Repository Project] salt irradiation effects program: Technical report

International Nuclear Information System (INIS)

Clark, D.E.

1986-11-01

The Engineering Review Group (ERG) was established by the Office of Nuclear Waste Isolation (ONWI) to help evaluate engineering-related issues in the US Department of Energy's nuclear waste repository program. The August 1985 meeting of the ERG reviewed the Salt Repository Project (SRP) salt irradiation effects program. This report documents the ERG's comments and recommendations on these subjects and the ONWI response to the specific points raised by the ERG

A Safety Case Approach for Deep Geologic Disposal of DOE HLW and DOE SNF in Bedded Salt - 13350

Energy Technology Data Exchange (ETDEWEB)

Sevougian, S. David [Advanced Nuclear Energy Programs Group, Sandia National Laboratories, P.O. Box 5800, Albuquerque, NM 87185 (United States); MacKinnon, Robert J. [Advanced Nuclear Energy Programs Group, Sandia National Laboratories, P.O. Box 5800, Albuquerque, NM 87185 (United States); Leigh, Christi D. [Defense Waste Management Programs Group, Sandia National Laboratories, P.O. Box 5800, Albuquerque, NM 87185 (United States); Hansen, Frank D. [Geoscience Research and Applications Group, Sandia National Laboratories, P.O. Box 5800, Albuquerque, NM 87185 (United States)

2013-07-01

The primary objective of this study is to investigate the feasibility and utility of developing a defensible safety case for disposal of United States Department of Energy (U.S. DOE) high-level waste (HLW) and DOE spent nuclear fuel (SNF) in a conceptual deep geologic repository that is assumed to be located in a bedded salt formation of the Delaware Basin [1]. A safety case is a formal compilation of evidence, analyses, and arguments that substantiate and demonstrate the safety of a proposed or conceptual repository. We conclude that a strong initial safety case for potential licensing can be readily compiled by capitalizing on the extensive technical basis that exists from prior work on the Waste Isolation Pilot Plant (WIPP), other U.S. repository development programs, and the work published through international efforts in salt repository programs such as in Germany. The potential benefits of developing a safety case include leveraging previous investments in WIPP to reduce future new repository costs, enhancing the ability to effectively plan for a repository and its licensing, and possibly expediting a schedule for a repository. A safety case will provide the necessary structure for organizing and synthesizing existing salt repository science and identifying any issues and gaps pertaining to safe disposal of DOE HLW and DOE SNF in bedded salt. The safety case synthesis will help DOE to plan its future R and D activities for investigating salt disposal using a risk-informed approach that prioritizes test activities that include laboratory, field, and underground investigations. It should be emphasized that the DOE has not made any decisions regarding the disposition of DOE HLW and DOE SNF. Furthermore, the safety case discussed herein is not intended to either site a repository in the Delaware Basin or preclude siting in other media at other locations. Rather, this study simply presents an approach for accelerated development of a safety case for a potential

A Safety Case Approach for Deep Geologic Disposal of DOE HLW and DOE SNF in Bedded Salt - 13350

International Nuclear Information System (INIS)

Sevougian, S. David; MacKinnon, Robert J.; Leigh, Christi D.; Hansen, Frank D.

2013-01-01

The primary objective of this study is to investigate the feasibility and utility of developing a defensible safety case for disposal of United States Department of Energy (U.S. DOE) high-level waste (HLW) and DOE spent nuclear fuel (SNF) in a conceptual deep geologic repository that is assumed to be located in a bedded salt formation of the Delaware Basin [1]. A safety case is a formal compilation of evidence, analyses, and arguments that substantiate and demonstrate the safety of a proposed or conceptual repository. We conclude that a strong initial safety case for potential licensing can be readily compiled by capitalizing on the extensive technical basis that exists from prior work on the Waste Isolation Pilot Plant (WIPP), other U.S. repository development programs, and the work published through international efforts in salt repository programs such as in Germany. The potential benefits of developing a safety case include leveraging previous investments in WIPP to reduce future new repository costs, enhancing the ability to effectively plan for a repository and its licensing, and possibly expediting a schedule for a repository. A safety case will provide the necessary structure for organizing and synthesizing existing salt repository science and identifying any issues and gaps pertaining to safe disposal of DOE HLW and DOE SNF in bedded salt. The safety case synthesis will help DOE to plan its future R and D activities for investigating salt disposal using a risk-informed approach that prioritizes test activities that include laboratory, field, and underground investigations. It should be emphasized that the DOE has not made any decisions regarding the disposition of DOE HLW and DOE SNF. Furthermore, the safety case discussed herein is not intended to either site a repository in the Delaware Basin or preclude siting in other media at other locations. Rather, this study simply presents an approach for accelerated development of a safety case for a potential

Approach to calculating upper bounds on maximum individual doses from the use of contaminated well water following a WIPP repository breach. Report EEG-9

International Nuclear Information System (INIS)

Spiegler, P.

1981-09-01

As part of the assessment of the potential radiological consequences of the proposed Waste Isolation Pilot Plant (WIPP), this report evaluates the post-closure radiation dose commitments associated with a possible breach event which involves dissolution of the repository by groundwaters and subsequent transport of the nuclear waste through an aquifer to a well assumed to exist at a point 3 miles downstream from the repository. The concentrations of uranium and plutonium isotopes at the well are based on the nuclear waste inventory presently proposed for WIPP and basic assumptions concerning the transport of waste as well as treatment to reduce the salinity of the water. The concentrations of U-233, Pu-239, and Pu-240, all radionuclides originally emplaced as waste in the repository, would exceed current EPA drinking water limits. The concentrations of U-234, U-235, and U-236, all decay products of plutonium isotopes originally emplaced as waste, would be well below current EPA drinking water limits. The 50-year dose commitments from one year of drinking treated water contaminated with U-233 or Pu-239 and Pu-240 were found to be comparable to a one-year dose from natural background. The 50-year dose commitments from one year of drinking milk would be no more than about 1/5 the dose obtained from ingestion of treated water. These doses are considered upper bounds because of several very conservative assumptions which are discussed in the report

Microbial Influence on the Performance of Subsurface, Salt-Based Radioactive Waste Repositories. An Evaluation Based on Microbial Ecology, Bioenergetics and Projected Repository Conditions

International Nuclear Information System (INIS)

Swanson, J.S.; Reed, D.T.; Cherkouk, A.; Arnold, T.; Meleshyn, A.; Patterson, Russ

2018-01-01

For the past several decades, the Nuclear Energy Agency Salt Club has been supporting and overseeing the characterisation of rock salt as a potential host rock for deep geological repositories. This extensive evaluation of deep geological settings is aimed at determining - through a multidisciplinary approach - whether specific sites are suitable for radioactive waste disposal. Studying the microbiology of granite, basalt, tuff, and clay formations in both Europe and the United States has been an important part of this investigation, and much has been learnt about the potential influence of microorganisms on repository performance, as well as about deep subsurface microbiology in general. Some uncertainty remains, however, around the effects of microorganisms on salt-based repository performance. Using available information on the microbial ecology of hyper-saline environments, the bioenergetics of survival under high ionic strength conditions and studies related to repository microbiology, this report summarises the potential role of microorganisms in salt-based radioactive waste repositories

Basic data report for Drillhole WIPP 14 (Waste Isolation Pilot Plant - WIPP)

International Nuclear Information System (INIS)

1982-08-01

Borehole WIPP 14 is an exploratory well drilled in eastern Eddy County, New Mexico, in section 9, T22S,R31E. The borehole was drilled to a depth of 1000.0 ft measured from ground level. It penetrated, from top to bottom, 15.4 ft of Quaternary sands, 125.6 ft of the Triassic Santa Rosa Sandstone, and in the Permian strata, 497.7 ft of the Dewey Lake Red Beds, 312.9 ft of the Rustler Formation and 48.4 ft of the Upper Salado Formation. Seven hundred feet of the well were cored, at consecutive and nonconsecutive 10-ft intervals to a depth of 925.5 ft. Cuttings were collected where core was not taken. Density, gamma ray neutron and caliper logs were run the full depth of the hole. The WIPP is a demonstration facility for the disposal of transuranic (TRU) waste from defense programs. The WIPP will also provide a research facility to investigate the interactions between bedded salt and high level wastes

Release consequence analysis for a hypothetical geologic radioactive waste repository in salt

International Nuclear Information System (INIS)

1979-08-01

One subtask conducted under the INFCE program is to evaluate and compare the health and safety impacts of different fuel cycles in which all radioactive wastes (except those from mining and milling) are placed in a geologic repository in salt. To achieve this objective, INFCE Working Group 7 examined the radiologic dose to humans from geologic repositories containing waste arisings as defined for seven reference fuel cycles. This report examines the release consequences for a generic waste repository in bedded salt. The top of the salt formation and the top of the repository are assumed to be 250 and 600 m, respectively, below the surface. The hydrogeologic structure above the salt consists of two aquifers and two aquitards. The aquifers connect to a river 6.2 km from the repository. The regional gradient to the river is 1 m/km in all aquifers. Hydrologic, transport, and dose models were used to model two release scenarios for each fuel cycle, one without a major disturbance and one in which a major geologic perturbation breached the repository immediately after it was sealed. The purpose of the modeling was to predict the rate of transport of radioactive contaminants from the repository through the geosphere to the biosphere, and to determine the potential dose to humans. Of the many radionuclides in the waste, only 129 I and 226 Ra arrived at the river in sufficient concentrations for a measurable dose calculation. Radionuclide concentrations in the ground water pose no threat to man because the ground water is a concentrated brine and it is diluted by a factor of 10 6 to 10 7 upon entering the river

Expected brine movement at potential nuclear waste repository salt sites

International Nuclear Information System (INIS)

McCauley, V.S.; Raines, G.E.

1987-08-01

The BRINEMIG brine migration code predicts rates and quantities of brine migration to a waste package emplaced in a high-level nuclear waste repository in salt. The BRINEMIG code is an explicit time-marching finite-difference code that solves a mass balance equation and uses the Jenks equation to predict velocities of brine migration. Predictions were made for the seven potentially acceptable salt sites under consideration as locations for the first US high-level nuclear waste repository. Predicted total quantities of accumulated brine were on the order of 1 m 3 brine per waste package or less. Less brine accumulation is expected at domal salt sites because of the lower initial moisture contents relative to bedded salt sites. Less total accumulation of brine is predicted for spent fuel than for commercial high-level waste because of the lower temperatures generated by spent fuel. 11 refs., 36 figs., 29 tabs

Shaft placement in a bedded salt repository

International Nuclear Information System (INIS)

Klasi, M.L.

1982-10-01

Preferred shaft pillar sizes and shaft locations were determined with respect to the induced thermal stresses in a generic bedded salt repository at a depth of 610 m with a gross thermal loading of 14.8 W/m 2 . The model assumes isotropic material properties, plane strain and linear elastic behavior. Various shaft locations were analyzed over a 25 year period. The thermal results show that for this time span, the stratigraphy is unimportant except for the region immediately adjacent to the repository. The thermomechanical results show that for the given repository depth of 610 m, a minimum central shaft pillar radius of 244 m is required to equal the material strength in the barrier pillar. An assumed constant stress and constant temperature distribution creep model of the central shaft region adjacent to the repository conservatively overestimates a creep closure of 310 mm in a 6.1 m diameter centrally-located shaft

The Wipp Disposal Decision Plan: the Successful Road Map for Transparent and Credible Decision-Making

International Nuclear Information System (INIS)

Eriksson, Leif G.

2001-01-01

The Waste Isolation Pilot Plant (WIPP) deep geological repository for long-lived, transuranic radioactive waste (TRUW) opened on the 26th of March 1999. Beginning on the 4th of April 1994, the United States Department of Energy (DOE), implemented the WIPP Disposal Decision Plan (DDP), which embodied the five-year vision and intents of the then DOE Manager of the Carlsbad Area Office (CAO), presently the Carlsbad Field Office (CBFO). The successful design and implementation of the DDP ensured good science, enhanced regulator and stake holder (affected and interested parties) interactions and acceptance of programmatic decisions, which resulted in the certification of the WIPP TRUW repository by the U.S. Environmental Protection Agency (EPA) on the 18th of May 1998, almost three years earlier than projected in November 1993. The present paper contains three sections: A concise background information on the CBFO's TRUW disposal program, incl. the legal framework, current status, and author-envisioned challenges and solutions; A description of the main components and attributes of the WIPP DDP. A summary of the lessons learned during and after the 1994 through 1998 implementation of the WIPP DDP

The Wipp Disposal Decision Plan: the Successful Road Map for Transparent and Credible Decision-Making

Energy Technology Data Exchange (ETDEWEB)

Eriksson, Leif G. [GRAM, Inc., Albuquerque, NM (United States)

2001-07-01

The Waste Isolation Pilot Plant (WIPP) deep geological repository for long-lived, transuranic radioactive waste (TRUW) opened on the 26th of March 1999. Beginning on the 4th of April 1994, the United States Department of Energy (DOE), implemented the WIPP Disposal Decision Plan (DDP), which embodied the five-year vision and intents of the then DOE Manager of the Carlsbad Area Office (CAO), presently the Carlsbad Field Office (CBFO). The successful design and implementation of the DDP ensured good science, enhanced regulator and stake holder (affected and interested parties) interactions and acceptance of programmatic decisions, which resulted in the certification of the WIPP TRUW repository by the U.S. Environmental Protection Agency (EPA) on the 18th of May 1998, almost three years earlier than projected in November 1993. The present paper contains three sections: A concise background information on the CBFO's TRUW disposal program, incl. the legal framework, current status, and author-envisioned challenges and solutions; A description of the main components and attributes of the WIPP DDP. A summary of the lessons learned during and after the 1994 through 1998 implementation of the WIPP DDP.

Salt Repository Project Waste Package Program Plan: Draft

International Nuclear Information System (INIS)

Carr, J.A.; Cunnane, J.C.

1986-01-01

Under the direction of the Office of Civilian Radioactive Waste Management (OCRWM) created within the DOE by direction of the Nuclear Waste Policy Act of 1982 (NWPA), the mission of the Salt Repository Project (SRP) is to provide for the development of a candidate salt repository for disposal of high-level radioactive waste (HLW) and spent reactor fuel in a manner that fully protects the health and safety of the public and the quality of the environment. In consideration of the program needs and requirements discussed above, the SRP has decided to develop and issue this SRP Waste Package Program Plan. This document is intended to outline how the SRP plans to develop the waste package design and to show, with reasonable assurance, that the developed design will satisfy applicable requirements/performance objectives. 44 refs., 16 figs., 16 tabs

Monitoring system specifications: retrieval of surf from a salt repository

International Nuclear Information System (INIS)

1980-01-01

The task of developing specifications for a reference monitoring system determined by repository environmental conditions, retrieval operations, and federal regulatory criteria is discussed. The monitoring system specified in this report is capable of measuring (1) package position and orientation, (2) vault deformation, (3) brine accumulation, (4) spent fuel dissolution, (5) temperature, (6) nuclear radiation, and (7) package condition with sufficient accuracy to provide data input to a general risk assessment model. In order to define a monitoring system which can provide probabilistic data on radiological risk to operating personnel and the general public for a salt mine repository, the following information is required: (1) a complete design of the salt SURF repository including inventory, density and waste package design details; (2) probalistic failure rate data on containment integrity of the SURF waste package; (3) probabilistic failure rate data on the monitoring system components

WIPP site and vicinity geological field trip

International Nuclear Information System (INIS)

Chaturvedi, L.

1980-10-01

The Environmental Evaluation Group is conducting an assessment of the radiological health risks to people from the Waste Isolation Pilot Plant. As a part of this work, EEG is making an effort to improve the understanding of those geological issues concerning the WIPP site which may affect the radiological consequences of the proposed repository. One of the important geological issues to be resolved is the timing and the nature of the dissolution processes which may have affected the WIPP site. EEG organized a two-day conference of geological scientists, on January 17-18, 1980. On the basis of the January conference and the June field trip, EEG has formed the following conclusions: (1) it has not been clearly established that the site or the surrounding area has been attacked by deep dissolution to render it unsuitable for the nuclear waste pilot repository; (2) the existence of an isolated breccia pipe at the site unaccompanied by a deep dissolution wedge, is a very remote possibility; (3) more specific information about the origin and the nature of the brine reservoirs is needed. An important question that should be resolved is whether each encounter with artesian brine represents a separate pocket or whether these occurrences are interconnected; (4) Anderson has postulated a major tectonic fault or a fracture system at the Basin margin along the San Simon Swale; (5) the area in the northern part of the WIPP site, identified from geophysical and bore hole data as the disturbed zone, should be further investigated to cleary understand the nature and significance of this structural anomaly; and (6) a major drawback encountered during the discussions of geological issues related to the WIPP site is the absence of published material that brings together all the known information related to a particular issue

Definition of the waste package environment for a repository located in salt

International Nuclear Information System (INIS)

Clark, D.E.; Bradley, D.J.

1983-01-01

The expected environmental conditions for emplaced waste packages in a salt repository are simulated in the materials testing program to evaluate performance. Synthetic brines, based on the analyses of actual brines (both intrusion and inclusion), are used for corrosion and leach testing. Elevated temperatures (to 150 0 C) and radiation fields of up to 10 3 rad/h are employed as conservative conditions to bracket expected performance and provide data for worst case scenarios. Obtaining a precise definition of the waste package environment in a salt repository and its change with time is closely tied to detailed site characterization of the candidate salt repository horizon. It is expected that field testing can augment some of the materials testing currently under way and can provide increased confidence in the predicted site-specific near-field conditions. 17 references, 5 figures, 1 table

Actinide chemistry research supporting the Waste Isolation Pilot Plant (WIPP): FY94 results

Energy Technology Data Exchange (ETDEWEB)

Novak, C.F. [ed.

1995-08-01

This document contains six reports on actinide chemistry research supporting the Waste Isolation Pilot Plant (WIPP). These reports, completed in FY94, are relevant to the estimation of the potential dissolved actinide concentrations in WIPP brines under repository breach scenarios. Estimates of potential dissolved actinide concentrations are necessary for WIPP performance assessment calculations. The specific topics covered within this document are: the complexation of oxalate with Th(IV) and U(VI); the stability of Pu(VI) in one WIPP-specific brine environment both with and without carbonate present; the solubility of Nd(III) in a WIPP Salado brine surrogate as a function of hydrogen ion concentration; the steady-state dissolved plutonium concentrations in a synthetic WIPP Culebra brine surrogate; the development of a model for Nd(III) solubility and speciation in dilute to concentrated sodium carbonate and sodium bicarbonate solutions; and the development of a model for Np(V) solubility and speciation in dilute to concentrated sodium Perchlorate, sodium carbonate, and sodium chloride media.

Actinide chemistry research supporting the Waste Isolation Pilot Plant (WIPP): FY94 results

International Nuclear Information System (INIS)

Novak, C.F.

1995-08-01

This document contains six reports on actinide chemistry research supporting the Waste Isolation Pilot Plant (WIPP). These reports, completed in FY94, are relevant to the estimation of the potential dissolved actinide concentrations in WIPP brines under repository breach scenarios. Estimates of potential dissolved actinide concentrations are necessary for WIPP performance assessment calculations. The specific topics covered within this document are: the complexation of oxalate with Th(IV) and U(VI); the stability of Pu(VI) in one WIPP-specific brine environment both with and without carbonate present; the solubility of Nd(III) in a WIPP Salado brine surrogate as a function of hydrogen ion concentration; the steady-state dissolved plutonium concentrations in a synthetic WIPP Culebra brine surrogate; the development of a model for Nd(III) solubility and speciation in dilute to concentrated sodium carbonate and sodium bicarbonate solutions; and the development of a model for Np(V) solubility and speciation in dilute to concentrated sodium Perchlorate, sodium carbonate, and sodium chloride media

Mass transfer and transport in salt repositories

International Nuclear Information System (INIS)

Pigford, T.H.; Chambre, P.L.; Lee, W.W.L.

1989-02-01

Salt is a unique rock isolation of nuclear waste because it is ''dry'' and nearly impermeable. In this paper we summarize some mass-transfer and transport analyses of salt repositories. First we analyses brine migration. Heating by high-level waste can cause brine in grain boundaries to move due to pressure-gradients. We analyze brine migration treating salt as a thermoelastic solid and found that brine migration is transient and localized. We use previously developed techniques to estimate release rates from waste packages by diffusion. Interbeds exist in salt and may be conduits for radionuclide migration. We analyze steady-state migration due to brine flow in the interbed, as a function of the Peclet number. Then we analyze transient mass transfer, both into the interbed and directly to salt, due only to diffusion. Finally we compare mass transfer rates of a waste cylinder in granite facing a fracture and in salt facing an interbed. In all cases, numerical illustrations of the analytic solution are given. 10 refs., 4 figs., 3 tabs

USGS studies of physical--chemical relationships in salt repositories

International Nuclear Information System (INIS)

Stewart, D.B.

1977-01-01

The amount and physical properties of brine that can occur in salt repositories at elevated temperatures and pressures adjacent to waste-bearing cannisters will have considerable impact on the mechanical strength and stability of the repository. Brine will form readily from H 2 O absorbed on surfaces, diffusion along grain boundaries, movement of fluid inclusions, dehydration of hydrous minerals such as gypsum, polyhalite or clays, or even from leakage through failed shaft openings. A T-P diagram for NaCl--H 2 O shows the limits for coexisting solid-liquid-gas assemblages in salt repositories. Isobaric T-X diagrams are included to show compositional details at pressures below the critical point and above it. Properties of the fluid phases such as volume, density, heat capacity, enthalpy, viscosity, surface tension, osmotic coefficients, etc. can be well described (>0.01% to 2 O. Because aggregates of solids are mechanically weakened by interstitial liquid, determination of mechanical properties of brine-bearing aggregates is needed. A maximum of one third by weight of brine (not H 2 O), and probably much less, will destroy rock strength

Backfill barriers for nuclear waste repositories in salt

Energy Technology Data Exchange (ETDEWEB)

Nowak, E J; Odoj, R; Merz, E [eds.

1981-06-01

Backfill materials were evaluated for containment of radionuclides, chemical modification of brine, and sensitivity to hydrothermal conditions. Experimental conditions were relevant to nuclear waste isolation in bedded salt. They were based on geologic conditions at the site of the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico, USA. Conclusions are: backfill mixtures surrounding the waste form and canister can provide a neutral or slightly acidic, potentially reducing environment, prevent convective aqueous flow, and act as an effective radionuclide migration barrier; bentonite is likely to remain hydrothermally stable but potentially sensitive to waste package interactions which could alter the pH, the ratio of dissolved ions, or the sorption properties of radionuclide species; effects of irradiation from high level waste should be investigated.

Evaluation of the suitability of the WIPP site

International Nuclear Information System (INIS)

Neill, R.H.; Channell, J.K.; Chaturvedi, L.; Little, M.S.; Rehfeldt, K.; Spiegler, P.

1983-05-01

Determination of the suitability of the site for WIPP is only the first major phase in the evaluation of the radiological impact of the repository on the public health and safety. The Environmental Evaluation Group (EEG) will continue to independently review the design of the facility, the operational procedures, the criteria for packaging and shipment of the waste, the plans, procedures and results of the WIPP experiments, emergency preparedness, adherence to EPA and pertinent NRC regulations, and other important features of the project. EEG has concluded from existing evidence that the Los Medanos site for the WIPP project has been characterized in sufficient detail to warrant confidence in the validation of the site for the permanent emplacement of approximately 6 million cubic feet of defense transuranic waste. This conclusion is based on the assumption that the maximum surface dose rate for the unshielded remote-handled transuranic waste canisters will be 100 rem/hr with a maximum radionuclide concentration of 23 Ci/liter. The Site and Preliminary Design Validation program, through the drilling of two shafts to the selected repository level at 2160 ft below the surface and excavation of about 9000 ft of tunnels, has confirmed the interpretations made about the subsurface geological conditions at the site. For an assessment of the potential radiation effects of the nuclear waste repository on the public health and safety, it is necessary to understand the regional geological and hydrological setting. Much work has been done to understand these conditions and to address several specific issues which have arisen as a result of such studies. However, it is almost inevitable that some questions remain unanswered at a given time in the decision-making process. EEG has identified work which still needs to be done at the Los Medanos site in order to improve confidence in the worst case scenario models of possible breaches of the repository

Review of the scientific and technical criteria for the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

1984-01-01

The panel has evaluated the scientific and technical adequacy of work being done on the Waste Isolation Pilot Plant (WIPP) project to satisfy the charge to the panel set out in Chapter 1. The panel concluded that the scientific work has been carried out with a high degree of professional competence. The panel notes that the geology revealed by shaft sinking and excavation of drifts and the preliminary measurements generally confirm the geologic expectations derived from surface explorations and boreholes. The purity and volume of the salt, the absence of brine pockets at the repository horizon in the areas excavated, the absence of breccia pipes and of toxic gases, and the nearly horizontal bedding of the salt indicate that a repository can be constructed that will meet the geologic criteria for site selection. Thus, the important issues about the geology at the site have been resolved, but there remain some issues about the hydrology and design of the facility that should be resolved before large-scale transuranic (TRU) waste emplacement begins. The panel's conclusions and recommendations regarding the following studies are presented: site selection and characterization; in-situ tests and experiments; waste acceptance criteria; design and construction of underground facilities; and performance assessment. 65 references, 17 figures, 3 tables

Certifying the Waste Isolation Pilot Plant: Lessons Learned from the WIPP Experience

International Nuclear Information System (INIS)

Anderson, D.R.; Chu, Margaret S.Y.; Froehlich, Gary K.; Howard, Bryan A.; Howarth, Susan M.; Larson, Kurt W.; Pickering, Susan Y.; Swift, Peter N.

1999-01-01

In May 1998, the US Environmental Protection Agency (EPA) certified the US Department of Energy's (DOE) Waste Isolation Pilot Plant (WIPP) as being in compliance with applicable long-term regulations governing the permanent disposal of spent nuclear fuel, high-level, and transuranic radioactive wastes. The WIPP is the first deep geologic repository in the US to have successfully demonstrated regulatory compliance with long-term radioactive waste disposal requirements. The first disposal of TRU waste at WIPP occurred on March 26, 1999. Many of the lessons learned during the WIPP Project's transition from site characterization and experimental research to the preparation of a successful application may be of general interest to other repository programs. During a four-year period (1992 to 1996), the WIPP team [including the DOE Carlsbad Area Office (CAO), the science advisor to CAO, Sandia National Laboratories (SNL), and the management and operating contractor of the WIPP site, Westinghouse Electric Corporation (WID)] met its aggressive schedule for submitting the application without compromising the integrity of the scientific basis for the long-term safety of the repository. Strong leadership of the CAO-SNL-WID team was essential. Within SNL, a mature and robust performance assessment (PA) allowed prioritization of remaining scientific activities with respect to their impact on regulatory compliance. Early and frequent dialog with EPA staff expedited the review process after the application was submitted. Questions that faced SNL are familiar to geoscientists working in site evaluation projects. What data should be gathered during site characterization? How can we know when data are sufficient? How can we know when our understanding of the disposal system is sufficient to support our conceptual models? What constitutes adequate ''validation'' of conceptual models for processes that act over geologic time? How should we use peer review and expert judgment? Other

Prospects for regional groundwater contamination due to karst landforms in Mescalero caliche at the WIPP site near Carlsbad, New Mexico

International Nuclear Information System (INIS)

Phillips, R.H.

1987-01-01

Plutonium from nuclear weapons production will be permanently buried in Permian salt beds at the Waste Isolation Pilot Plant (WIPP), located in the Nash Draw watershed. Overlying the salt beds are cavernous Rustler dolomite aquifers, the most likely flow paths for contaminated water from WIPP to the biosphere. Overlying the Rustler are sandstones, siltstones, Mescalero caliche, and windblown sand. The WIPP site contains thousands of closed topographic depressions. If some are karst features, the ability of WIPP to isolate nuclear waste cannot be demonstrated. A water balance and geochemical analysis of the Nash Draw watershed and nearby brine springs were undertaken to determine: (1) which Rustler aquifers discharge where, and in what quantities; (2) the rates of evapotranspiration and natural groundwater recharge; (3) the most likely discharge point for contaminated water from WIPP. Laguna Grande, a natural salt lake in Nash Draw, is the outlet for the Rustler dolomite aquifers and for plutonium contaminations from WIPP. The recharge time for the Rustler may be only 6 to 8 years. WIPP is unsuitable for nuclear waste isolation because: (1) Rustler groundwater flow paths and travel times are inherently unpredictable; (2) caliche and sandstones allow rainwater recharge of the Rustler; (3) pressurized brine underneath WIPP can carry dissolved waste up the WIPP shafts to the Rustler; (4) geologic barriers between the brine and WIPP are unreliable; and (5) WIPP is vulnerable to human intrusion

Expected environment for waste packages in a salt repository

International Nuclear Information System (INIS)

Pederson, L.R.; Clark, D.E.; Hodges, F.N.; McVay, G.L.; Rai, D.

1983-01-01

This paper discusses results of recent efforts to define the very near-field (within approximately 2 m) environmental conditions to which waste packages will be exposed in a salt repository. These conditions must be considered in the experimental design for waste package materials testing, which includes corrosion of barrier materials and leaching of waste forms. Site-specific brine compositions have been determined, and standard brine compositions have been selected for testing purposes. Actual brine compositions will vary depending on origin, temperature, irradiation history, and contact with irradiated rock salt. Results of irradiating rock salt, synthetic brines, rock salt/brine mixtures, and reactions of irradiated rock salt with brine solutions are reported. 38 references, 3 figures, 2 tables

The function of packing materials in a high-level nuclear waste repository and some candidate materials: Salt Repository Project

International Nuclear Information System (INIS)

Bunnell, L.R.; Shade, J.W.

1987-03-01

Packing materials should be included in waste package design for a high-level nuclear waste repository in salt. A packing material barrier would increase confidence in the waste package by alleviating possible shortcomings in the present design and prolonging confinement capabilities. Packing materials have been studied for uses in other geologic repositories; appropriately chosen, they would enhance the confinement capabilities of salt repository waste packages in several ways. Benefits of packing materials include retarding or chemically modifying brines to reduce corrosion of the waste package, providing good thermal conductivity between the waste package and host rock, retarding or absorbing radionuclides, and reducing the massiveness of the waste package. These benefits are available at low percentage of total repository cost, if the packing material is properly chosen and used. Several candidate materials are being considered, including oxides, hydroxides, silicates, cement-based mixtures, and clay mixtures. 18 refs

Thermophysical properties of reconsolidating crushed salt.

Energy Technology Data Exchange (ETDEWEB)

Bauer, Stephen J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Urquhart, Alexander [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-03-01

Reconsolidated crushed salt is being considered as a backfilling material placed upon nuclear waste within a salt repository environment. In-depth knowledge of thermal and mechanical properties of the crushed salt as it reconsolidates is critical to thermal/mechanical modeling of the reconsolidation process. An experimental study was completed to quantitatively evaluate the thermal conductivity of reconsolidated crushed salt as a function of porosity and temperature. The crushed salt for this study came from the Waste Isolation Pilot Plant (WIPP). In this work the thermal conductivity of crushed salt with porosity ranging from 1% to 40% was determined from room temperature up to 300°C, using two different experimental methods. Thermal properties (including thermal conductivity, thermal diffusivity and specific heat) of single-crystal salt were determined for the same temperature range. The salt was observed to dewater during heating; weight loss from the dewatering was quantified. The thermal conductivity of reconsolidated crushed salt decreases with increasing porosity; conversely, thermal conductivity increases as the salt consolidates. The thermal conductivity of reconsolidated crushed salt for a given porosity decreases with increasing temperature. A simple mixture theory model is presented to predict and compare to the data developed in this study.

WIPP Recertification - An Environmental Evaluation Group Perspective

International Nuclear Information System (INIS)

Allen, L. E.; Silva, M. K.

2003-01-01

The Waste Isolation Pilot Plant (WIPP), a repository for defense transuranic (TRU) waste, was built and is operated by the U.S. Department of Energy (DOE). The WIPP Land Withdrawal Act (LWA) required initial certification of compliance of the WIPP by the U.S. Environmental Protection Agency (EPA). In addition, a recertification decision is required by the LWA every five years, dated from the initial receipt of TRU waste. The first TRU waste shipment arrived at the WIPP on March 26, 1999, and therefore the first recertification application is due from DOE to EPA by March 25, 2004. The Environmental Evaluation Group (EEG) provides technical oversight of the WIPP project on behalf of the State of New Mexico. The EEG considers the first recertification as a precedent setting event. Therefore, the EEG began the identification of recertification issues immediately following the initial certification decision. These issues have evolved since that time, based on discussions with the DOE and EEG's understanding of DOE's ongoing research. Performance assessment is required by the EPA certification and its results are needed to determine whether the facility remains in compliance at the time of the recertification application. The DOE must submit periodic change reports to the EPA which summarize activities and conditions that differ from the compliance application. Also, the EPA may request additional information from the DOE that may pertain to continued compliance. These changes and new information must be considered for recertification performance assessment

WIPP site and vicinity geological field trip

International Nuclear Information System (INIS)

Chaturvedi, L.

1980-10-01

The Environmental Evaluation Group (EEG) is conducting an assessment of the radiological health risks to people from the Waste Isolation Pilot Plant (WIPP). As a part of this work, EEG is making an effort to improve the understanding of those geological issues concerning the WIPP site which may affect the radiological consequences of the proposed repository. One of the important geological issues to be resolved is the timing and the nature of the dissolution processes which may have affected the WIPP site. EEG organized a two-day conference of geological scientists, titled Geotechnical Considerations for Radiological Hazard Assessment of WIPP on January 17-18, 1980. During this conference, it was realized that a field trip to the site would further clarify the different views on the geological processes active at the site. The field trip of June 16-18, 1980 was organized for this purpose. This report provides a summary of the field trip activities along with the participants post field trip comments. Important field stops are briefly described, followed by a more detailed discussion of critical geological issues. The report concludes with EEG's summary and recommendations to the US Department of Energy for further information needed to more adequately resolve concerns for the geologic and hydrologic integrity of the site

Assessment of Contaminated Brine Fate and Transport in MB139 at WIPP

Energy Technology Data Exchange (ETDEWEB)

Kuhlman, Kristopher L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Applied Systems Analysis and Research Dept.; Malama, Bwalya [Sandia National Lab., Carlsbad, NM (United States). Performance Assessment Dept.

2014-07-01

Following the radionuclide release event of February 14, 2014 at the Waste Isolation Pilot Plant (WIPP), actinide contamination has been found on the walls and floor in Panel 7 as a result of a release in Room 7 of Panel 7. It has been proposed to decontaminate Panel 7 at the WIPP by washing contaminated surfaces in the underground with fresh water. A cost-effective cleanup of this contamination would allow for a timely return to waste disposal operations at WIPP. It is expected that the fresh water used to decontaminate Panel 7 will flow as contaminated brine down into the porosity of the materials under the floor – the run-of-mine (ROM) salt above Marker Bed 139 (MB139) and MB139 itself – where its fate will be controlled by the hydraulic and transport properties of MB139. Due to the structural dip of MB139, it is unlikely that this brine would migrate northward towards the Waste-Handling Shaft sump. A few strategically placed shallow small-diameter observation boreholes straddling MB139 would allow for monitoring the flow and fate of this brine after decontamination. Additionally, given that flow through the compacted ROM salt floor and in MB139 would occur under unsaturated (or two-phase) conditions, there is a need to measure the unsaturated flow properties of crushed WIPP salt and salt from the disturbed rock zone (DRZ).

Rock salt as a medium for long-term isolation of radioactive wastes - a reassessment

International Nuclear Information System (INIS)

Chaturvedi, L.

1985-01-01

Rock salt has been regarded as a suitable medium for the permanent disposal of high and medium level radioactive wastes since the National Academy of Sciences recommended it in 1957. As a result of detained site-specific studies conducted for the Waste Isolation Pilot Plant (WIPP) project in New Mexico, however, several potential problems which are unique to bedded salt deposits have emerged. These include 1) the need to delineate the extent and rate of past dissolution and projections for the future, 2) the origin and significance of brines often found underlying the salt beds, 3) the rate and volume of migration of brine from the salt crystals towards the heat producing waste canisters, 4) the creep rates and implications for retrievability, and 5) the existence of potash and oil and gas resources with implications of human intrusion in the future. These questions will also be faced for sites in salt domes with added complications due to more complex structure and hydrology. The experience at WIPP shows that the site characterization process for high level waste repositories in bedded or dome salt should aim at identifying the important issues of site suitability early in the process and a clear program should be established to address these issues

Planning, developing, and fielding of thermal/structural interactions in situ tests for the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Munson, D.E.; Matalucci, R.V.

1986-01-01

Large-scale, well-instrumented underground tests to determine in situ thermal/structural response of bedded salt are being constructed in the WIPP facility in southeastern New Mexico. These tests are an essential component of a broad research and development program to resolve thermal/structural issues, to validate long-term prediction methods, and to develop a design basis for a future repository. They are the result of an extensive planning and evaluation procedure to determine the appropriate test configuration. All details of the tests, including background, decisions, design, site operations, and testing organization are explained. These procedures may be useful in developing other in situ tests

Model-based studies into ground water movement, with water density depending on salt content. Case studies and model validation with respect to the long-term safety of radwaste repositories. Final report

International Nuclear Information System (INIS)

Schelkes, K.

1995-12-01

Near-to-reality studies into ground water movement in the environment of planned radwaste repositories have to take into account that the flow conditions are influenced by the water density which in turn depends on the salt content. Based on results from earlier studies, computer programs were established that allow computation and modelling of ground water movement in salt water/fresh water systems, and the programs were tested and improved according to progress of the studies performed under the INTRAVAL international project. The computed models of ground water movement in the region of the Gorlebener Rinne showed for strongly simplified model profiles that the developing salinity distribution varies very sensitively in response to the applied model geometry, initial input data for salinity distribution, time frame of the model, and size of the transversal dispersion length. The WIPP 2 INTRAVAL experiment likewise studied a large-area ground water movement system influenced by salt water. Based on the concept of a hydraulically closed, regional ground water system (basin model), a sectional profile was worked out covering all relevant layers of the cap rock above the salt formation planned to serve as a repository. The model data derived to describe the salt water/fresh water movements in this profile resulted in essential enlargements and modifications of the ROCKFLOW computer program applied, (relating to input data for dispersion modelling, particle-tracker, computer graphics interface), and yielded important information for the modelling of such systems (relating to initial pressure data at the upper margin, network enhancement for important concentration boundary conditions, or treatment of permeability contrasts). (orig.) [de

Options Assessment Report: Treatment of Nitrate Salt Waste at Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Robinson, Bruce Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stevens, Patrice Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-12-17

This report documents the methodology used to select a method of treatment for the remediated nitrate salt (RNS) and unremediated nitrate salt (UNS) waste containers at Los Alamos National Laboratory (LANL). The method selected should treat the containerized waste in a manner that renders the waste safe and suitable for transport and final disposal in the Waste Isolation Pilot Plant (WIPP) repository, under specifications listed in the WIPP Waste Acceptance Criteria (DOE/CBFO, 2013). LANL recognizes that the results must be thoroughly vetted with the New Mexico Environment Department (NMED) and that a modification to the LANL Hazardous Waste Facility Permit is a necessary step before implementation of this or any treatment option. Likewise, facility readiness and safety basis approvals must be received from the Department of Energy (DOE). This report presents LANL’s preferred option, and the documentation of the process for reaching the recommended treatment option for RNS and UNS waste, and is presented for consideration by NMED and DOE.

Options assessment report: Treatment of nitrate salt waste at Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Robinson, Bruce Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stevens, Patrice Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-09-16

This report documents the methodology used to select a method of treatment for the remediated nitrate salt (RNS) and unremediated nitrate salt (UNS) waste containers at Los Alamos National Laboratory (LANL). The method selected should treat the containerized waste in a manner that renders the waste safe and suitable for transport and final disposal in the Waste Isolation Pilot Plant (WIPP) repository, under specifications listed in the WIPP Waste Acceptance Criteria (DOE/CBFO, 2013). LANL recognized that the results must be thoroughly vetted with the New Mexico Environment Department (NMED) and the a modification to the LANL Hazardous Waste Facility Permit is a necessary step before implementation of this or any treatment option. Likewise, facility readiness and safety basis approvals must be received from the Department of Energy (DOE). This report presents LANL's preferred option, and the documentation of the process for reaching the recommended treatment option for RNS and UNS waste, and is presented for consideration by NMED and DOE.

Conclusions regarding geotechnical acceptability of the WIPP site

International Nuclear Information System (INIS)

Weart, W.D.

1983-01-01

The Waste Isolation Pilot Plant (WIPP) was authorized by Congress in 1980 as an unlicensed research and development (R and D) facility to demonstrate the safe disposal of radioactive wastes arising from the defense activities and programs of the United States. WIPP is now being constructed in southeast New Mexico, using salt beds about 655 m below the surface of the ground. Construction of the full WIPP facility will not commence until a preliminary underground excavation phase, called Site and Preliminary Design Validation (SPDV), is satisfactorily concluded in the summer of 1983. This SPDV program permits confirmation of subsurface geology, in drifts at planned facility depth that extend for 1555 m in a north-south direction, and in the two vertical shafts that provide access to these drifts. The subsurface studies are nearing completion, and it is therefore appropriate to draw conclusions regarding the geotechnical acceptability of the WIPP site. Four geotechnical elements are discussed: dissolution, deformation, hydrologic regime, and natural resources

WIPP Regulatory Compliance Strategy and Management Plan for demonstrating compliance to long-term disposal standards

International Nuclear Information System (INIS)

1994-05-01

The primary purpose of this document is to provide a strategy by which the WIPP will demonstrate its ability to perform as a deep geologic repository. The document communicates the DOE's understanding of the regulations related to long-term repository performance; and provides the most efficient strategy that intergrates WIPP Project elements, ensures the sufficiency of information, and provides flexibility for changes in the TRU waste generation system to facilitate the disposal of defense-generated TRU wastes. In addition, this document forms a focal point between the DOE and its various external regulators as well as other stakeholders for the purpose of arriving at compliance decisions that consider all relevant input

Emplacement and retrieval equipment design considerations for a repository in salt

International Nuclear Information System (INIS)

Nair, B.R.; Bahorich, R.J.

1987-01-01

The current design concept for the disposal of nuclear high level waste packages in a repository in salt is based on the emplacement of individual packages in vertical boreholes in the underground mine floor. A key requirement is that the waste packages be capable of being retrieved during the last 26 years of the 76-year repository operating period. The unique design considerations relating to the retrieval of waste packages emplaced in bedded salt are presented in this paper. The information is based on the experience developed during the design of vertical emplacement and retrieval equipment in support of the Sandia Defense High Level Waste experiments at the Waste Isolation Pilot Plant. Also included are the impact of retrievability on the design of the equipment, the special salt cutting technology that was developed for this application, and a description of the equipment

Compilation of data for thermomechanical analyses of four potential salt repositories

International Nuclear Information System (INIS)

Tammemagi, H.Y.; Loken, M.C.; Osnes, J.D.; Wagner, R.A.

1986-01-01

This report includes a collection and summarization of the data which are necessary to perform thermomechanical analyses of four potential salt repository sites: Paradox Basin, Utah; Permian Basin, Texas; Richton Dome, Mississippi; and Vacherie Dome, Louisiana. Thermal, mechanical, and hydrogeological material properties are presented so that the numerical analyses can be subdivided into three geometric regions: canister, disposal room, and repository site. Data are presented for the salt formations, the surrounding geological units, and for human-made materials placed in the repository such as the nuclear waste and its protective steel liner. Wherever possible, site-specific data are used which have been determined from laboratory testing of drill core or from interpretation of geophysical logs. Although much effort has been made to obtain the most appropriate data, there are deficiencies because some of the required site-specific data are either not available or are inconsistent with anticipated values

Status of the safety concept and safety demonstration for an HLW repository in salt. Summary report

Energy Technology Data Exchange (ETDEWEB)

Bollingerfehr, W.; Buhmann, D.; Filbert, W.; and others

2013-12-15

Salt formations have been the preferred option as host rocks for the disposal of high level radioactive waste in Germany for more than 40 years. During this period comprehensive geological investigations have been carried out together with a broad spectrum of concept and safety related R and D work. The behaviour of an HLW repository in salt formations, particularly in salt domes, has been analysed in terms of assessment of the total system performance. This was first carried out for concepts of generic waste repositories in salt and, since 1998, for a repository concept with specific boundary conditions, taking the geology of the Gorleben salt dome as an example. Suitable repository concepts and designs were developed, the technical feasibility has been proven and operational and long-term safety evaluated. Numerical modelling is an important input into the development of a comprehensive safety case for a waste repository. Significant progress in the development of numerical tools and their application for long-term safety assessment has been made in the last two decades. An integrated approach has been used in which the repository concept and relevant scientific and engineering data are combined with the results from iterative safety assessments to increase the clarity and the traceability of the evaluation. A safety concept that takes full credit of the favourable properties of salt formations was developed in the course of the R and D project ISIBEL, which started in 2005. This concept is based on the safe containment of radioactive waste in a specific part of the host rock formation, termed the containment providing rock zone, which comprises the geological barrier, the geotechnical barriers and the compacted backfill. The future evolution of the repository system will be analysed using a catalogue of Features, Events and Processes (FEP), scenario development and numerical analysis, all of which are adapted to suit the safety concept. Key elements of the

Testing of high-level waste forms under repository conditions

International Nuclear Information System (INIS)

Mc Menamin, T.

1989-01-01

The workshop on testing of high-level waste forms under repository conditions was held on 17 to 21 October 1988 in Cadarache, France, and sponsored by the Commission of the European Communities (CEC), the Commissariat a l'energie atomique (CEA) and the Savannah River Laboratory (US DOE). Participants included representatives from Australia, Belgium, Denmark, France, Germany, Italy, Japan, the Netherlands, Sweden, Switzerland, The United Kingdom and the United States. The first part of the conference featured a workshop on in situ testing of simulated nuclear waste forms and proposed package components, with an emphasis on the materials interface interactions tests (MIIT). MIIT is a sevent-part programme that involves field testing of 15 glass and waste form systems supplied by seven countries, along with potential canister and overpack materials as well as geologic samples, in the salt geology at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, USA. This effort is still in progress and these proceedings document studies and findings obtained thus far. The second part of the meeting emphasized multinational experimental studies and results derived from repository systems simulation tests (RSST), which were performed in granite, clay and salt environments

The legal, regulatory and safety basis for opening WIPP

International Nuclear Information System (INIS)

Dials, G.E.

1997-01-01

Current laws in the United States of America direct the U.S. Department of Energy (DOE) to site, design, operate, and decommission a deep geological repository for safe disposal of transuranic radioactive waste (TRUW) at the Waste Isolation Pilot Plant (WIPP) site. In 1993, the DOE established the Carlsbad Area Office (CAO) to integrate the nation's management of TRUW and to open the WIPP site for safe disposal of TRUW in compliance with applicable laws and regulations. The CAO submitted the final Compliance Certification Application (CCA) in 1996, and is on schedule to open WIPP in November 1997, about three years earlier than scheduled before the establishment of the CAO. The performance assessment (PA) embodied in the CCA demonstrates that WIPP meets the EPA's regulatory requirements for radioactive releases for the 10,000 year regulatory period in both the undisturbed and disturbed (human intrusion) scenarios. Detailed planning, compliance-based research and development (R and D), teamwork among project participants and early and open iterative interactions with the regulators, oversight groups and other interested parties in the certification/permitting process are key components of the progress in the safe disposal of long-lived radioactive wastes. (author)

Technical evaluation of WIPP by the New Mexico environmental evaluation group

International Nuclear Information System (INIS)

Neill, R.

1988-01-01

The Waste Isolation Pilot Plant (WIPP) is a repository under construction in southeastern New Mexico for the disposal of 14.1 million curies of defense transuranic (TRU) waste. The US Department of Energy (DOE) plans to start storing waste in the underground facility in October 1988 for a 5-yr research and demonstration period. Since the State of New Mexico had a number of concerns in 1978 regarding the impact on health and safety of the proposed WIPP facility for disposal of radioactive waste, the DOE agreed to fund an independent technical review and evaluation of the planned repository, resulting in the creation of the Environmental Evaluation Group (EEG). This full-time multidisciplinary group has published 39 major reports to date, testified before the New Mexico Legislature and the US Congress, and has disseminated the results of analyses to DOE, the governor, the legislature, the Congress, the scientific community, and the general public. While the disposal of radioactive defense mill tailings and defense high-level wastes are both subject to US Nuclear Regulatory Commission (NRC) licensing, Congress specifically chose not to have defense TRU waste disposal licensed by the NRC. This has placed a heavy burden on EEG as the only full-time technical review agency on WIPP, but without regulatory authority

Waste package for a repository located in salt

International Nuclear Information System (INIS)

Basham, S.J. Jr.

1983-01-01

This paper describes the current status of the waste package designs for salt repositories. The status of the supporting studies of environment definition, corrosion of containment materials, and leaching of waste forms is also presented. Emphasis is on the results obtained in FY 83 and the planned effort in FY 84. 8 references, 3 figures, 1 table

The Revised WIPP Passive Institutional Controls Program - A Conceptual Plan - 13145

International Nuclear Information System (INIS)

Patterson, Russ; Klein, Thomas; Van Luik, Abraham

2013-01-01

The Department of Energy/Carlsbad Field Office (DOE/CBFO) is responsible for managing all activities related to the disposal of TRU and TRU-mixed waste in the geologic repository, 650 m below the land surface, at WIPP, near Carlsbad, New Mexico. The main function of the Passive Institutional Controls (PIC's) program is to inform future generations of the long-lived radioactive wastes buried beneath their feet in the desert. For the first 100 years after cessation of disposal operations, the rooms are closed and the shafts leading underground sealed, WIPP is mandated by law to institute Active Institutional Controls (AIC's) with fences, gates, and armed guards on patrol. At this same time a plan must be in place of how to warn/inform the future, after the AIC's are gone, of the consequences of intrusion into the geologic repository disposal area. A plan was put into place during the 1990's with records management and storage, awareness triggers, permanent marker design concepts and testing schedules. This work included the thoughts of expert panels and individuals. The plan held up under peer review and met the requirements of the U.S. Environmental Protection Agency (EPA). Today the NEA is coordinating a study called the 'Preservation of Records, Knowledge and Memory (RK and M) Across Generations' to provide the international nuclear waste repository community with a guide on how a nuclear record archive programs should be approached and developed. CBFO is cooperating and participating in this project and will take what knowledge is gained and apply that to the WIPP program. At the same time CBFO is well aware that the EPA and others are expecting DOE to move forward with planning for the future WIPP PIC's program; so a plan will be in place in time for WIPP's closure slated for the early 2030's. The DOE/CBFO WIPP PIC's program in place today meets the regulatory criteria, but complete feasibility of implementation is questionable, and may not be in conformance

Preliminary evaluation of solution-mining intrusion into a salt-dome repository

International Nuclear Information System (INIS)

1981-06-01

This report is the product of the work of an ONWI task force to evaluate inadvertant human intrusion into a salt dome repository by solution mining. It summarizes the work in the following areas: a general review of the levels of defense that could reduce both the likelihood and potential consequences of human intrusion into a salt dome repository; evaluation of a hypothetical intrusion scenario and its consequences; recommendation for further studies. The conclusions of this task force report can be summarized as follows: (1) it is not possible at present to establish with certainty that solution mining is credible as a human-intrusion event. The likelihood of such an intrusion will depend on the effectiveness of the preventive measures; (2) an example analysis based on the realistic approach is presented in this report; it concluded that the radiological consequences are strongly dependent upon the mode of radionuclide release from the waste form, time after emplacement, package design, impurities in the host salt, the amount of a repository intercepted, the solution mining cavity form, the length of time over which solution mining occurs, the proportion of contaminated salt source for human consumption compared to other sources, and the method of salt purification for culinary purposes; (3) worst case scenarios done by other studies suggest considerable potential for exposures to man while preliminary evaluations of more realistic cases suggest significantly reduced potential consequences. Mathematical model applications to process systems, guided by more advanced assumptions about human intrusion into geomedia, will shed more light on the potential for concerns and the degree to which mitigative measures will be required

Basic data report for drillhole ERDA 6 (Waste Isolation Pilot Plant - WIPP)

International Nuclear Information System (INIS)

1983-01-01

ERDA 6 was drilled in eastern Eddy County, New Mexico, to investigate a candidate site for a nuclear waste repository. The site was subsequently rejected on the basis of geological data. ERDA 6 was drilled in the NE 1/4 SE 1/4, section 35, T21S,R31E. The borehole encountered, from top to bottom, 17 ft of Quaternary deposits, 55 ft of the Triassic Santa Rosa Sandstone, 466 ft of the Dewey Lake Red Beds, 273 ft of the Rustler Formation, 1785.5 ft of the Salado Formation and 374.5 ft of the upper Castile Formation, all of Permian age. Cores or drill cuttings were taken throughout the hole. A suite of wireline geophysical logs was run to a depth of 883 ft to facilitate the recognition and correlation of rock units, to assure identification of major lithologies and to provide depth determinations independent of drill-pipe measurements. The site at ERDA 6 was rejected because the structure of the lower Salado and the Castile is too severe to develop a repository along a single set of beds. The borehole also intersected a reservoir of pressurized brine and gas at about 2710'. The pore volume for the reservoir was estimated to be in the range from about 200,000 to about 2 million barrels. ERDA 6 was re-entered in 1981 by the Department of Energy (DOE) for the purpose of further testing the brine reservoir. Those tests are described in separate reports by the DOE and its contractors. The WIPP is a demonstration facility for the disposal of transuranic (TRU) waste from defense programs. The WIPP will also provide a research facility to investigate the interactions between bedded salt and high level wastes

Basic data report for drillhole ERDA 6 (Waste Isolation Pilot Plant - WIPP)

Energy Technology Data Exchange (ETDEWEB)

1983-01-01

ERDA 6 was drilled in eastern Eddy County, New Mexico, to investigate a candidate site for a nuclear waste repository. The site was subsequently rejected on the basis of geological data. ERDA 6 was drilled in the NE 1/4 SE 1/4, section 35, T21S,R31E. The borehole encountered, from top to bottom, 17 ft of Quaternary deposits, 55 ft of the Triassic Santa Rosa Sandstone, 466 ft of the Dewey Lake Red Beds, 273 ft of the Rustler Formation, 1785.5 ft of the Salado Formation and 374.5 ft of the upper Castile Formation, all of Permian age. Cores or drill cuttings were taken throughout the hole. A suite of wireline geophysical logs was run to a depth of 883 ft to facilitate the recognition and correlation of rock units, to assure identification of major lithologies and to provide depth determinations independent of drill-pipe measurements. The site at ERDA 6 was rejected because the structure of the lower Salado and the Castile is too severe to develop a repository along a single set of beds. The borehole also intersected a reservoir of pressurized brine and gas at about 2710'. The pore volume for the reservoir was estimated to be in the range from about 200,000 to about 2 million barrels. ERDA 6 was re-entered in 1981 by the Department of Energy (DOE) for the purpose of further testing the brine reservoir. Those tests are described in separate reports by the DOE and its contractors. The WIPP is a demonstration facility for the disposal of transuranic (TRU) waste from defense programs. The WIPP will also provide a research facility to investigate the interactions between bedded salt and high level wastes.

The waste isolation pilot plant transuranic waste repository: A case study in radioactive waste disposal safety and risk

Energy Technology Data Exchange (ETDEWEB)

Eriksson, Leif G. [GRAM, Inc., Albuquerque, NM (United States)

1999-12-01

The Waste Isolation Pilot Plant (WIPP) deep geological defense-generated transuranic radioactive waste (TRUW) repository in the United States was certified on the 13 of May 1998 and opened on the 26 of March 1999. Two sets of safety/performance assessment calculations supporting the certification of the WIPP TRUW repository show that the maximum annual individual committed effective dose will be 32 times lower than the regulatory limit and that the cumulative amount of radionuclide releases will be at least 10 times, more likely at least 20 times, lower than the regulatory limits. Yet, perceptions remain among the public that the WIPP TRUW repository imposes an unacceptable risk.

The waste isolation pilot plant transuranic waste repository: A case study in radioactive waste disposal safety and risk

International Nuclear Information System (INIS)

Eriksson, Leif G.

1999-01-01

The Waste Isolation Pilot Plant (WIPP) deep geological defense-generated transuranic radioactive waste (TRUW) repository in the United States was certified on the 13 of May 1998 and opened on the 26 of March 1999. Two sets of safety/performance assessment calculations supporting the certification of the WIPP TRUW repository show that the maximum annual individual committed effective dose will be 32 times lower than the regulatory limit and that the cumulative amount of radionuclide releases will be at least 10 times, more likely at least 20 times, lower than the regulatory limits. Yet, perceptions remain among the public that the WIPP TRUW repository imposes an unacceptable risk

Radiation induced F-center and colloid formation in synthetic NaCl and natural rock salt: applications to radioactive waste repositories

International Nuclear Information System (INIS)

Levy, P.W.; Loman, J.M.; Kierstead, J.A.

1983-01-01

Radiation damage, particularly Na metal colloid formation, has been studied in synthetic NaCl and natural rock salt using unique equipment for making optical absorption, luminescence and other measurements during irradiation with 1 to 3 MeV electrons. Previous studies have established the F-center and colloid growth phenomenology. At temperatures where colloids form most rapidly, 100 to 250 C, F-centers appear when the irradiation is initiated and increase at a decreasing rate to a plateau, reached at doses of 10 6 to 10 7 rad. Concomitant colloid growth is described by classical nucleation and growth curves with the transition to rapid growth occurring at 10 6 to 10 7 rad. The colloid growth rate is low at 100 C, increases markedly to a maximum at 150 to 175 C and decreases to a negligible rate at 225 C. At 1.2x10 8 rad/h the induction period is >10 4 sec at 100 C, 10 4 sec at 275 C. The colloid growth in salt from 14 localities is well described by C(dose)/sup n/ relations. Data on WIPP site salt (Los Medanos, NM, USA) has been used to estimate roughly the colloid expected in radioactive waste repositories. Doses of 1 to 2x10 10 rad, which will accumulate in salt adjacent to lightly shielded high level canisters in 200 to 500 years, will convert between 1 and 100% of the salt to Na colloids (and Cl) if back reactions or other limiting reactions do not occur. Each high level lightly shielded canister may ultimately be surrounded by 200 to 300 kg of colloid sodium. Low level or heavily shielded canisters may produce as little as 1 kg sodium

Comparison of risks due to HLW and SURF repositories in bedded salt

International Nuclear Information System (INIS)

Chu, M.S.Y.; Ortiz, N.R.; Wahi, K.K.

1983-01-01

A methodology was developed for use in the analysis of risks from geologic disposal of nuclear wastes. This methodology is applied to two conceptual nuclear waste repositories in bedded salt containing High-Level Waste (HLW) and Spent Un-Reprocessed Fuel (SURF), respectively. A comparison of the risk estimated from the HLW and SURF repositories is presented

Further design work on a repository in a salt dome

International Nuclear Information System (INIS)

Hamstra, J.; Janssen, L.G.L.

1985-01-01

The report presents the cost estimate and the work plan for the construction of a repository, to be mined in a medium-size salt dome for the simultaneous disposal of different categories of solid radioactive wastes. The repository is designed for all categories of waste from 40 years of operation of 25 nuclear power stations of 1000 MWe each, including the decommissioning waste from these stations as well as all the radioactive wastes from the hospitals and laboratories during a hundred-year period. The cost estimate includes preparation of a site, the construction, operation and abandonment of that repository. Moreover, an outline has been presented for a future updating and optimization study of the concept

Radiological consequences associated with human intrusion into radioactive waste repositories in salt formations

International Nuclear Information System (INIS)

Jacquier, P.

1989-01-01

The assessment of the radiological impact of human intrusion scenarios is extremely important in the case of repositories located in salt formations, since salt is obviously a valuable economic resource. Salt formations also represent a suitable medium for mining storage caverns for oil and gas. The scenario considered in this report is that of solution mining in salt formations to produce salt for human consumption. It is postulated that the salt is extracted by excavating a cavern through solution-mining and that, in the course of cavern enlargement, the waste is intercepted and drops to the bottom of the cavern. We have assumed that the intrusion takes place 500 or even 2 500 years after the repository has been sealed. The cases considered involve high-level vitrified waste or cemented alpha waste. The paper describes the assumptions on which the scenario is based and uses a simplified model to assess the radiological consequences associated with the ingestion of contaminated salt. The paper also provides details of a sensitivity/uncertainty analysis which identified several areas in which experimental studies should be either initiated or continued [fr

Analysis of the geological stability of a hypothetical radioactive waste repository in a bedded salt formation

International Nuclear Information System (INIS)

Tierney, M.S.; Lusso, F.; Shaw, H.R.

1978-01-01

This document reports on the development of mathematical models used in preliminary studies of the long-term safety of radioactive wastes deeply buried in bedded salt formations. Two analytical approaches to estimating the geological stability of a waste repository in bedded salt are described: (a) use of probabilistic models to estimate the a priori likelihoods of release of radionuclides from the repository through certain idealized natural and anthropogenic causes, and (b) a numerical simulation of certain feedback effects of emplacement of waste materials upon ground-water access to the repository's host rocks. These models are applied to an idealized waste repository for the sake of illustration

Waste handling building design tradeoff studies: Salt Repository Project closeout task report

International Nuclear Information System (INIS)

1988-01-01

The purpose of this closeout study is to capture work done by SRPO contractors and the relevant knowledge and recommendations of Battelle staff regarding design of WHB receiving, storage, hot cell areas, and process logistics. The information and recommendations are based on the latest available studies and prior experience of Battelle personnel at WIPP, INEL, and Hanford facilities. The information is expected to be directly applicable to WHB design work that will be done at Nevada, MRS, or other repository facilities. A perspective showing the various WHB areas and general arrangement is given. This study addresses alternatives associated with the receiving area, the fuel storage areas, the cell arrangements, the failed fuel accommodations, and the process logistics. 16 refs., 2 figs., 5 tabs

Sample management implementation plan: Salt Repository Project

International Nuclear Information System (INIS)

1987-01-01

The purpose of the Sample Management Implementation Plan is to define management controls and building requirements for handling materials collected during the site characterization of the Deaf Smith County, Texas, site. This work will be conducted for the US Department of Energy Salt Repository Project Office (SRPO). The plan provides for controls mandated by the US Nuclear Regulatory Commission and the US Environmental Protection Agency. Salt Repository Project (SRP) Sample Management will interface with program participants who request, collect, and test samples. SRP Sample Management will be responsible for the following: (1) preparing samples; (2) ensuring documentation control; (3) providing for uniform forms, labels, data formats, and transportation and storage requirements; and (4) identifying sample specifications to ensure sample quality. The SRP Sample Management Facility will be operated under a set of procedures that will impact numerous program participants. Requesters of samples will be responsible for definition of requirements in advance of collection. Sample requests for field activities will be approved by the SRPO, aided by an advisory group, the SRP Sample Allocation Committee. This document details the staffing, building, storage, and transportation requirements for establishing an SRP Sample Management Facility. Materials to be managed in the facility include rock core and rock discontinuities, soils, fluids, biota, air particulates, cultural artifacts, and crop and food stuffs. 39 refs., 3 figs., 11 tabs

Salt Repository Project: FY 85 technical project plan

International Nuclear Information System (INIS)

1985-07-01

The FY 85 technical plan for the Salt Repository Project is briefly presented. The objectives of the project in relation to the Civilian Radioactive Waste Management Program are discussed, and the technical activities directed toward accomplishing these objectives are detailed. A budget is presented for each of the Level 2 work breakdown structure tasks (Systems, Waste Package, Site, Repository, Regulatory and Institutional, Exploratory Shaft, Test Facilities, Land Acquisition, and Project Management) in the various sections. An overall description, current status, and planned activities are presented for each of the subtasks which make up the above-mentioned Level 2 tasks. A strategy diagram and a master schedule are included and each of the milestones is also listed chronologically in the sections

Salt Repository Project. FY-84 technical project plan

International Nuclear Information System (INIS)

1984-08-01

The FY 84 technical plans for the Salt Repository Project (SRP) are briefly presented. The objectives of the project in relation to the Civilian Radioactive Waste Management (CRWM) program are discused and the technical activities directed toward accomplishing these objectives are detailed. A budget is presented for each of the Level 2 Work Breakdown Structure Tasks (Systems, Waste Package, Site, Repository, Regulatory and Institutional, Test Facilities, Exploratory Shaft, Land Acquisition, and Program Management) in an appendix. An overall description, current status, and planned activities are presented for each of the subtasks which make up the above-mentioned Level 2 tasks. Milestones and their definitions for the plan year, as well as milestones for the outyears are also presented at this same subtask level for each subtask

Asse salt mine nuclear waste repository simulation experiments

International Nuclear Information System (INIS)

Coyle, A.J.

1983-01-01

The field tests underway in Asse, Federal Republic of Germany are dicected toward the development of test plans, techniques and equipment to be used in Exploratory Shafts or At Depth Test Facilities confirmation tests. These simulated repository tests will also provide information which address the following issues: brine migration (liquid and vapor); radiation effects of gamma rays; gas generation caused by radiation and corrosion; accelerated corrosion and leaching; altered properties of salt (the effects of heat, radiation and brine); and the effects of heat and radiation on test assemblies, instruments, and various materials exposed to repository conditions. This paper is a status of the first 82 days of operation of the Asse Brine Migration Tests, which were initiated on May 25, 1983. 6 references

A review of WIPP [Waste Isolation Pilot Plant] repository clays and their relationship to clays of adjacent strata

International Nuclear Information System (INIS)

Krumhansl, J.L.; Kimball, K.M.; Stein, C.L.

1990-12-01

The Salado Formation is a thick evaporite sequence located in the Permian Delaware Basin of southeastern New Mexico. This study focuses on the intense diagenetic alteration that has affected the small amounts of clay, feldspar, and quartz washed into the basin during salt deposition. These changes are of more than academic interest since this formation also houses the WIPP (Waste Isolation Pilot Plant). Site characterization concerns warrant compiling a detailed data base describing the clays in and around the facility horizon. An extensive sampling effort was undertaken to address these programmatic issues as well as to provide additional insight regarding diagenetic mechanisms in the Salado. Seventy-five samples were collected from argillaceous partings in halite at the stratigraphic level of the Waste Isolation Pilot Plant (WIPP). These were compared with twenty-eight samples from cores of the Vaca Triste member of the Salado, a thin clastic unit at the top of the McNutt potash zone, and with a clay-rich sample from the lower contact of the Culebra Dolomite (in the overlying Rustler Formation). These settings were compared to assess the influence of differences in brine chemistry (i.e., halite and potash facies, normal to hypersaline marine conditions) and sediment composition (clays, sandy silt, dolomitized limestone) on diagenetic processes. 44 refs., 11 figs., 5 tabs

WIPP Status and Plans - 2013 - 13379

Energy Technology Data Exchange (ETDEWEB)

Nelson, R.A.; Franco, J. [U.S. Department of Energy, PO Box 3090, Carlsbad, NM 88220 (United States)

2013-07-01

An up-to-date look at the many aspects of America's only deep geologic long-lived radioactive waste repository is presented in this paper. WIPP's mission includes coordination of all Department of Energy (DOE) sites to prepare, package and characterize defense transuranic waste for final shipment and emplacement in WIPP. The Waste Isolation Pilot Plant (WIPP) is completing its 14. year of operations. Five of the ten planned disposal panels have been filled and sealed from ventilation, with about half of the legislated volume capacity consumed. About 11,000 shipments have been made successfully, traveling more than 40 million kilometers across the nation's highways. A fleet of new Type B shipping packages, the TRUPACT-III, has been added to the transportation capability, with an ongoing campaign to de-inventory large waste items from the Savannah River Site, while minimizing size reduction and repackaging. A new shipping and emplacement method for remote handled waste in shielded containers has been approved for disposal, and will significantly improve operational efficiency. Remote handled waste packaged in these shielded containers will be shipped, handled and emplaced as contact handled waste. Also described is a new criticality control over-pack container, which will improve efficiency when shipping high fissile-content waste streams consisting of Special Nuclear Material declared as waste from nuclear weapons sites. The paper describes the importance of the infrastructure at WIPP to ensure disposal site availability for defense transuranic waste sites across the weapons complex. With the facility reaching its original design lifetime, there are many infrastructure maintenance and improvements being planned and performed. (authors)

Salt repository project: Technical progress report for the quarter 1 April--30 June 1987

International Nuclear Information System (INIS)

1987-01-01

This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of Energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation

Salt Repository Project technical progress report for the quarter 1 January--31 March 1987

International Nuclear Information System (INIS)

1988-03-01

This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation. 23 refs., 1 fig

Evaluation of iron-base materials for waste package containers in a salt repository

International Nuclear Information System (INIS)

Westerman, R.E.; Nelson, J.L.; Kuhn, W.L.; Basham, S.G.; Moak, D.A.; Pitman, S.G.

1983-11-01

Design studies for high-level nuclear waste packages for salt repositories have identified low-carbon steel as a candidate material for containers. Among the requirements are strength, corrosion resistance, and fabricability. The studies of the corrosion resistance and structural stability of iron-base materials (particularly low-carbon steel) are treated in this paper. The materials have been exposed in brines that are characteristic of the potential sites for salt repositories. The effects of temperature, radiation level, oxygen level and other parameters are under investigation. The initial development of corrosion models for these environments is presented with discussion of the key mechanisms under consideration. 6 references, 5 figures

Simultaneous Thermal Analysis of WIPP and LANL Waste Drum Samples: A Preliminary Report

Energy Technology Data Exchange (ETDEWEB)

Wayne, David M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-10-19

On Friday, February 14, 2014, an incident in P7R7 of the WIPP underground repository released radioactive material into the environment. The direct cause of the event was a breached transuranic (TRU) waste container, subsequently identified as Drum 68660. Photographic and other evidence indicates that the breach of 68660 was caused by an exothermic event. Subsequent investigations (Britt, 2015; Clark and Funk, 2015; Wilson et al., 2015; Clark, 2015) indicate that the combination of nitrate salts, pH neutralizing chemicals, and organic-based adsorbent represented a potentially energetic mixture. The materials inside the breached steel drum consisted of remediated, 30- to 40-year old, Pu processing wastes from LANL. The contents were processed and repackaged in 2014. Processing activities at LANL included: 1) neutralization of acidic liquid contents, 2) sorption of the neutralized liquid, and 3) mixing of acidic nitrate salts with an absorber to meet waste acceptance criteria. The contents of 68660 and its sibling, 68685, were derived from the same parent drum, S855793. Drum S855793 originally contained ten plastic bags of acidic nitrate salts, and four bags of mixed nitrate and oxalate salts generated in 1985 by Pu recovery operations. These salts were predominantly oxalic acid, hydrated nitrate salts of Mg, Ca, and Fe, anhydrous Na(NO₃), and minor amounts of anhydrous and hydrous nitrate salts of Pb, Al, K, Cr, and Ni. Other major components include sorbed water, nitric acid, dissolved nitrates, an absorbent (Swheat Scoop®) and a neutralizer (KolorSafe®). The contents of 68660 are described in greater detail in Appendix E of Wilson et al. (2015)

Simultaneous Thermal Analysis of WIPP and LANL Waste Drum Samples: A Preliminary Report

International Nuclear Information System (INIS)

Wayne, David M.

2015-01-01

On Friday, February 14, 2014, an incident in P7R7 of the WIPP underground repository released radioactive material into the environment. The direct cause of the event was a breached transuranic (TRU) waste container, subsequently identified as Drum 68660. Photographic and other evidence indicates that the breach of 68660 was caused by an exothermic event. Subsequent investigations (Britt, 2015; Clark and Funk, 2015; Wilson et al., 2015; Clark, 2015) indicate that the combination of nitrate salts, pH neutralizing chemicals, and organic-based adsorbent represented a potentially energetic mixture. The materials inside the breached steel drum consisted of remediated, 30- to 40-year old, Pu processing wastes from LANL. The contents were processed and repackaged in 2014. Processing activities at LANL included: 1) neutralization of acidic liquid contents, 2) sorption of the neutralized liquid, and 3) mixing of acidic nitrate salts with an absorber to meet waste acceptance criteria. The contents of 68660 and its sibling, 68685, were derived from the same parent drum, S855793. Drum S855793 originally contained ten plastic bags of acidic nitrate salts, and four bags of mixed nitrate and oxalate salts generated in 1985 by Pu recovery operations. These salts were predominantly oxalic acid, hydrated nitrate salts of Mg, Ca, and Fe, anhydrous Na(NO 3 ), and minor amounts of anhydrous and hydrous nitrate salts of Pb, Al, K, Cr, and Ni. Other major components include sorbed water, nitric acid, dissolved nitrates, an absorbent (Swheat Scoop®) and a neutralizer (KolorSafe®). The contents of 68660 are described in greater detail in Appendix E of Wilson et al. (2015)

WIPP - Pre-Licensing and Operations: Developer and Regulator Perspectives

International Nuclear Information System (INIS)

Peake, Tom; Patterson, R.

2014-01-01

The Waste Isolation Pilot Plant (WIPP) is a disposal system for defense-related transuranic (TRU) radioactive waste. Developed by the Department of Energy (DOE), WIPP is located in Southeastern New Mexico: radioactive waste is disposed of 2,150 feet underground in an ancient layer of salt with a total capacity of 6.2 million cubic feet of waste. Congress authorized the development and construction of WIPP in 1980 for the express purpose of providing a research and development facility to demonstrate the safe disposal of radioactive wastes resulting from the defense activities and programs of the United States. This paper makes a historical review of the site development, site operations (waste disposal operations started in 1999), communications between US EPA and DOE, the chronology of pre-licensing and pre-operations, the operational phase and the regulatory challenges, and the lessons learned after 12 years of operations

Aspects on the gas generation and migration in repositories for high level waste in salt formations

International Nuclear Information System (INIS)

Ruebel, Andre; Buhmann, Dieter; Meleshyn, Artur; Moenig, Joerg; Spiessl, Sabine

2013-07-01

In a deep geological repository for high-level waste, gases may be produced during the post-closure phase by several processes. The generated gases can potentially affect safety relevant features and processes of the repository, like the barrier integrity, the transport of liquids and gases in the repository and the release of gaseous radionuclides from the repository into the biosphere. German long-term safety assessments for repositories for high-level waste in salt which were performed prior 2010 did not explicitly consider gas transport and the consequences from release of volatile radionuclides. Selected aspects of the generation and migration of gases in repositories for high-level waste in a salt formation are studied in this report from the viewpoint of the performance assessment. The knowledge on the availability of water in the repository, in particular the migration of salt rock internal fluids in the temperature field of the radioactive waste repository towards the emplacement drifts, was compiled and the amount of water was roughly estimated. Two other processes studied in this report are on the one hand the release of gaseous radionuclides from the repository and their potential impact in the biosphere and on the other hand the transport of gases along the drifts and shafts of the repository and their interaction with the fluid flow. The results presented show that there is some gas production expected to occur in the repository due to corrosion of container material from water disposed of with the backfill and inflowing from the host rock during the thermal phase. If not dedicated gas storage areas are foreseen in the repository concept, these gases might exceed the storage capacity for gases in the repository. Consequently, an outflow of gases from the repository could occur. If there are failed containers for spent fuel, radioactive gases might be released from the containers into the gas space of the backfill and subsequently transported together

Salt Repository emplacement mode evaluation and selection: Final report

International Nuclear Information System (INIS)

1988-03-01

This document describes the decision analysis performed to evaluate and compare the emplacement mode for the Salt Repository. The study was commissioned to recommend one emplacement mode to the Salt Repository Project Office using multi-attribute decision analysis. The nature of the decision required analysis of uncertain outcomes and conflicting attributes and offers a high degree of objectivity for these types of decisions since the decision model is structured to allow only the facts to enter into the final decision. The analysis requires an explicit definition of the attributes used to evaluate the alternative (e.g., cost, safety, environmental impact), the definition of a utility function over the attributes which incorporated both risk attitudes and trade-offs between attributes, and the probability distribution over the outcomes that would result from the selection of one alternative over the other. The decision process is described and results are given. A simulation model was developed to evaluate the probability distributions over the attributes. This report documents logic, inputs and results of this model. Final ranking of alternatives is given. Extensive technical backup documentation is included in the appendices to provide the quantitative basis for this decision. 5 refs., 2 figs., 8 tabs

Assessment of Effectiveness of Geologic Isolation Systems: REFERENCE SITE INITIAL ASSESSMENT FOR A SALT DOME REPOSITORY

Energy Technology Data Exchange (ETDEWEB)

Harwell, M. A.; Brandstetter, A.; Benson, G. L.; Raymond, J. R.; Brandley, D. J.; Serne, R. J.; Soldat, J. K.; Cole, C. R.; Deutsch, W. J.; Gupta, S. K.; Harwell, C. C.; Napier, B. A.; Reisenauer, A. E.; Prater, L. S.; Simmons, C. S.; Strenge, D. L.; Washburn, J. F.; Zellmer, J. T.

1982-06-01

As a methodology demonstration for the Office of Nuclear Waste Isolation (ONWI), the Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program conducted an initial reference site analysis of the long-term effectiveness of a salt dome repository. The Hainesville Salt Dome in Texas was chosen to be representative of the Gulf Coast interior salt domes; however, the Hainesville Site has been eliminated as a possible nuclear waste repository site. The data used for this exercise are not adequate for an actual assessment, nor have all the parametric analyses been made that would adequately characterize the response of the geosystem surrounding the repository. Additionally, because this was the first exercise of the complete AEGIS and WASTE Rock Interaction Technology (WRIT) methodology, this report provides the initial opportunity for the methodology, specifically applied to a site, to be reviewed by the community outside the AEGIS. The scenario evaluation, as a part of the methodology demonstration, involved consideration of a large variety of potentially disruptive phenomena, which alone or in concert could lead to a breach in a salt dome repository and to a subsequent transport of the radionuclides to the environment. Without waste- and repository-induced effects, no plausible natural geologic events or processes which would compromise the repository integrity could be envisioned over the one-million-year time frame after closure. Near-field (waste- and repository-induced) effects were excluded from consideration in this analysis, but they can be added in future analyses when that methodology development is more complete. The potential for consequential human intrusion into salt domes within a million-year time frame led to the consideration of a solution mining intrusion scenario. The AEGIS staff developed a specific human intrusion scenario at 100 years and 1000 years post-closure, which is one of a whole suite of possible scenarios. This scenario

Compliance status summaries for federal and state statutory directives that apply to the Salt Repository Project at the Deaf Smith County Site, Texas

International Nuclear Information System (INIS)

1986-07-01

This document contains statutory summaries, checklists of compliance requirements, status summaries, and lists of information needs for the environmental and health and safety statutory directives at Federal and State levels that apply to the Salt Repository Project at the Deaf Smith County Site, Texas. Statutes that apply in general to any repository project but not specifically to the Deaf Smith are not included. The information herein supplements the Salt Repository Project Statutory Compliance Plan and the Salt Repository Project Permitting Management Plan by providing lengthy details on statutory directives, compliance requirements, information needs, and the overall status of the environmental and health and safety compliance program for the Salt Repository Project at the Deaf Smith County Site, Texas

Conceptual model for regional radionuclide transport from a salt dome repository: a technical memorandum

International Nuclear Information System (INIS)

Kier, R.S.; Showalter, P.A.; Dettinger, M.D.

1980-01-01

Disposal of high-level radioactive wastes is a major environmental problem influencing further development of nuclear energy in this country. Salt domes in the Gulf Coast Basin are being investigated as repository sites. A major concern is geologic and hydrologic stability of candidate domes and potential transport of radionuclides by groundwater to the biosphere prior to their degradation to harmless levels of activity. This report conceptualizes a regional geohydrologic model for transport of radionuclides from a salt dome repository. The model considers transport pathways and the physical and chemical changes that would occur through time prior to the radionuclides reaching the biosphere. Necessary, but unknown inputs to the regional model involve entry and movement of fluids through the repository dome and across the dome-country rock interface and the effect on the dome and surrounding strata of heat generated by the radioactive wastes

Proceedings of the 7th US/German Workshop on Salt Repository Research, Design, and Operation.

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Steininger, Walter [Karisruhe Inst. of Technology (Germany); Bollingerfehr, Willhelm [DBE TECHNOLOGY GmbH (Germany)

2017-01-01

The 7th US/German Workshop on Salt Repository Research, Design, and Operation was held in Washington, DC on September 7-9, 2016. Over fifty participants representing governmental agencies, internationally recognized salt research groups, universities, and private companies helped advance the technical basis for salt disposal of radioactive waste. Representatives from several United States federal agencies were able to attend, including the Department of Energy´s Office of Environmental Management and Office of Nuclear Energy, the Environmental Protection Agency, the Nuclear Regulatory Commission, and the Nuclear Waste Technical Review Board. A similar representation from the German ministries showcased the covenant established in a Memorandum of Understanding executed between the United States and Germany in 2011. The US/German workshops´ results and activities also contribute significantly to the Nuclear Energy Agency Salt Club repository research agenda.

Nuclear waste repository simulation experiments. Asse salt mine: Annual report 1984

International Nuclear Information System (INIS)

Rothfuchs, T.; Feddersen, H.K.; Schwarzianeck, P.; Staupendahl, G.; Coyle, A.J.; Kalia, H.; Eckert, J.

1985-01-01

This is the Second Annual Report (1984) which describes experiments simulating a nuclear waste repository at the 800 meter-level of the Asse Salt Mine in the Federal Republic of Germany. The report describes the Asse Salt Mine, the test equipment, and the pretest properties of the salt in the mine and in the vicinity of the test area. Also included are test data for the first sixteen months of operation on the following: brine migration rates, thermal mechanical behavior of the salt (including room closure, stress readings and thermal profiles) and borehole gas pressures. In addition to field data laboratory analyses of results are also included in this report. The duration of the experiment will be two years, ending in December 1985. (orig.)

Salt repository sealing materials development program: 5-year work plan

International Nuclear Information System (INIS)

Myers, L.B.

1986-06-01

This plan covers 5 years (fiscal years 1986 through 1990) of work in the repository sealing materials program to support design decisions and licensing activities for a salt repository. The plan covers a development activity, not a research activity. There are firm deliverables as the end points of each part of the work. The major deliverables are: development plans for code development and materials testing; seal system components models; seal system performance specifications; seal materials specifications; and seal materials properties ''handbook.'' The work described in this plan is divided into three general tasks as follows: mathematical modeling; materials studies (salt, cementitious materials, and earthen materials); and large-scale testing. Each of the sections presents an overview, status, planned activities, and summary of program milestones. This plan will be the starting point for preparing the development plans described above, but is subject to change if preparation of the work plan indicates that a different approach or sequence is preferable to achieve the ultimate goal, i.e., support of design and licensing

Brine and Gas Flow Patterns Between Excavated Areas and Disturbed Rock Zone in the 1996 Performance Assessment for the Waste Isolation Pilot Plant for a Single Drilling Intrusion that Penetrates Repository and Castile Brine Reservoir

Energy Technology Data Exchange (ETDEWEB)

ECONOMY,KATHLEEN M.; HELTON,JON CRAIG; VAUGHN,PALMER

1999-10-01

The Waste Isolation Pilot Plant (WIPP), which is located in southeastern New Mexico, is being developed for the geologic disposal of transuranic (TRU) waste by the U.S. Department of Energy (DOE). Waste disposal will take place in panels excavated in a bedded salt formation approximately 2000 ft (610 m) below the land surface. The BRAGFLO computer program which solves a system of nonlinear partial differential equations for two-phase flow, was used to investigate brine and gas flow patterns in the vicinity of the repository for the 1996 WIPP performance assessment (PA). The present study examines the implications of modeling assumptions used in conjunction with BRAGFLO in the 1996 WIPP PA that affect brine and gas flow patterns involving two waste regions in the repository (i.e., a single waste panel and the remaining nine waste panels), a disturbed rock zone (DRZ) that lies just above and below these two regions, and a borehole that penetrates the single waste panel and a brine pocket below this panel. The two waste regions are separated by a panel closure. The following insights were obtained from this study. First, the impediment to flow between the two waste regions provided by the panel closure model is reduced due to the permeable and areally extensive nature of the DRZ adopted in the 1996 WIPP PA, which results in the DRZ becoming an effective pathway for gas and brine movement around the panel closures and thus between the two waste regions. Brine and gas flow between the two waste regions via the DRZ causes pressures between the two to equilibrate rapidly, with the result that processes in the intruded waste panel are not isolated from the rest of the repository. Second, the connection between intruded and unintruded waste panels provided by the DRZ increases the time required for repository pressures to equilibrate with the overlying and/or underlying units subsequent to a drilling intrusion. Third, the large and areally extensive DRZ void volumes is a

Brine and Gas Flow Patterns Between Excavated Areas and Disturbed Rock Zone in the 1996 Performance Assessment for the Waste Isolation Pilot Plant for a Single Drilling Intrusion that Penetrates Repository and Castile Brine Reservoir

International Nuclear Information System (INIS)

Economy, Kathleen M.; Helton, Jon Craig; Vaughn, Palmer

1999-01-01

The Waste Isolation Pilot Plant (WIPP), which is located in southeastern New Mexico, is being developed for the geologic disposal of transuranic (TRU) waste by the U.S. Department of Energy (DOE). Waste disposal will take place in panels excavated in a bedded salt formation approximately 2000 ft (610 m) below the land surface. The BRAGFLO computer program which solves a system of nonlinear partial differential equations for two-phase flow, was used to investigate brine and gas flow patterns in the vicinity of the repository for the 1996 WIPP performance assessment (PA). The present study examines the implications of modeling assumptions used in conjunction with BRAGFLO in the 1996 WIPP PA that affect brine and gas flow patterns involving two waste regions in the repository (i.e., a single waste panel and the remaining nine waste panels), a disturbed rock zone (DRZ) that lies just above and below these two regions, and a borehole that penetrates the single waste panel and a brine pocket below this panel. The two waste regions are separated by a panel closure. The following insights were obtained from this study. First, the impediment to flow between the two waste regions provided by the panel closure model is reduced due to the permeable and areally extensive nature of the DRZ adopted in the 1996 WIPP PA, which results in the DRZ becoming an effective pathway for gas and brine movement around the panel closures and thus between the two waste regions. Brine and gas flow between the two waste regions via the DRZ causes pressures between the two to equilibrate rapidly, with the result that processes in the intruded waste panel are not isolated from the rest of the repository. Second, the connection between intruded and unintruded waste panels provided by the DRZ increases the time required for repository pressures to equilibrate with the overlying and/or underlying units subsequent to a drilling intrusion. Third, the large and areally extensive DRZ void volumes is a

Calculation of density and permeability of compacted crushed salt within an engineered shaft sealing system

International Nuclear Information System (INIS)

Loken, M.; Statham, W.

1997-01-01

Crushed salt from the host Salado Formation is proposed as a sealing material in one component of a multicomponent seal system design for the shafts of the Waste Isolation Pilot Plant (WIPP), a mined geological repository for storage and disposal of transuranic radioactive wastes located near Carlsbad, New Mexico. The crushed salt will be compacted and placed at a density approaching 90% of the intact density of the host Salado salt. Creep closure of the shaft will further compact the crushed salt over time, thereby reducing the crushed-salt permeability from the initial state and creating an effective long-term seal. A structural model and a fluid flow model have been developed to provide an estimate of crushed-salt reconsolidation rate as a function of depth, time, and pore pressure. Model results are obtained in terms of crushed-salt permeability as a function of time and depth within the salt column. Model results indicate that average salt column permeability will be reduced to 3.3 x 10 -20 m 2 in about 100 years, which provides for an acceptable long-term seal component

Performance assessment plans and methods for the Salt Repository Project

International Nuclear Information System (INIS)

1984-08-01

This document presents the preliminary plans and anticipated methods of the Salt Repository Project (SRP) for assessing the postclosure and radiological aspects of preclosure performance of a nuclear waste repository in salt. This plan is intended to be revised on an annual basis. The emphasis in this preliminary effort is on the method of conceptually dividing the system into three subsystems (the very near field, the near field, and the far field) and applying models to analyze the behavior of each subsystem and its individual components. The next revision will contain more detailed plans being developed as part of Site Characterization Plan (SCP) activities. After a brief system description, this plan presents the performance targets which have been established for nuclear waste repositories by regulatory agencies (Chapter 3). The SRP approach to modeling, including sensitivity and uncertainty techniques is then presented (Chapter 4). This is followed by a discussion of scenario analysis (Chapter 5), a presentation of preliminary data needs as anticipated by the SRP (Chapter 6), and a presentation of the SRP approach to postclosure assessment of the very near field, the near field, and the far field (Chapters 7, 8, and 9, respectively). Preclosure radiological assessment is discussed in Chapter 10. Chapter 11 presents the SRP approach to code verification and validation. Finally, the Appendix lists all computer codes anticipated for use in performance assessments. The list of codes will be updated as plans are revised

Salt Repository Project input to seismic design: Revision 0

International Nuclear Information System (INIS)

1987-12-01

The Salt Repository Program (SRP) Input to Seismic Design (ISD) documents the assumptions, rationale, approaches, judgments, and analyses that support the development of seismic-specific data and information to be used for shaft design in accordance with the SRP Shaft Design Guide (SDG). The contents of this document are divided into four subject areas: (1) seismic assessment, (2) stratigraphy and material properties for seismic design, (3) development of seismic design parameters, and (4) host media stability. These four subject areas have been developed considering expected conditions at a proposed site in Deaf Smith County, Texas. The ISD should be used only in conjunction with seismic design of the exploratory and repository shafts. Seismic design considerations relating to surface facilities are not addressed in this document. 54 refs., 55 figs., 18 tabs

Salt Repository Project transportation system interface requirements: Transportation system/repository receiving facility interface requirements

International Nuclear Information System (INIS)

Smith, L.A.; Insalaco, J.W.; Trainer, T.A.

1988-01-01

This report is a preliminary review of the interface between the transportation system and the repository receiving facility for a nuclear waste mined geologic disposal system in salt. Criteria for generic cask and facility designs are developed. These criteria are derived by examining the interfaces that occur as a result of the operations needed to receive nuclear waste at a repository. These criteria provide the basis for design of a safe, operable, practical nuclear waste receiving facility. The processing functions required to move the shipping unit from the gate into the unloading area and back to the gate for dispatch are described. Criteria for a generic receiving facility are discussed but no specific facility design is presented or evaluated. The criteria are stated in general terms to allow application to a wide variety of cask and facility designs. 9 refs., 6 figs., 4 tabs

Effects of gaseous radioactive nuclides on the design and operation of repositories for spent LWR fuel in rock salt

International Nuclear Information System (INIS)

Jenks, G.H.

1979-12-01

Information relating to the identities and amounts of gaseous radionuclides present in spent LWR fuel and to their release from canistered spent fuel under plausible storage and disposal conditions was assembled, reviewed, and analyzed. Information was also reviewed and analyzed on several other subjects that relate to the integrity of the carbon steel canister in which the spent fuel is to be encapsulated and to the expected rates of transfer of gaseous radionuclides through crushed salt backfill within a disposal room in a reference repository in rock salt. The advantages and disadvantages were considered for several different canister-backfill materials, and recommendations were made regarding preferred materials. Other recommendations relate to encapsulation procedures and specifications and to needs for additional experimental studies. The objective of this work was to provide reference information, conclusions, and recommendations that could be used to establish design and operating conditions and procedures for a bedded salt repository for spent LWR fuel and that could also be used to help evaluate the safety of the repository. The results of this work will also generally apply to spent fuel repositories in domal salt. However, because the domal salt may have little or no brine inclusions within it, there may be little or no possibility that brine will migrate into open spaces around an emplaced canister. Addordingly, some of the concerns that result from the possible occurrence of brine migration in bedded salt may be of no importance in domal salt

Science to compliance: The WIPP success story

International Nuclear Information System (INIS)

Howarth, S.M.; Chu, M.S.; Shephard, L.E.

1997-01-01

The Waste Isolation Pilot Plant (WIPP) in southeast New Mexico has been studied as a transuranic waste repository for the past 23 years. During this time, an extensive site characterization, design, construction, and experimental program was completed to provide in-depth understanding of the dominant processes that are most likely to influence the containment of radionuclides for 10,000 years. The success of the program, however, is defined by the regulator in the context of compliance with performance criteria, rather than by the in-depth technical understanding typical of most scientific programs. The WIPP project was successful in making a transformation from science to compliance by refocusing and redirecting programmatic efforts toward the singular goal of meeting regulatory compliance requirements while accelerating the submittal of the Compliance Certification Application (CCA) by two months from the April 1994 Disposal Decision Plan (DDP) date of December 1996, and by reducing projected characterization costs by more than 40%. This experience is unparalleled within the radioactive waste management community and has contributed to numerous lessons learned from which the entire community can benefit

Expert (Peer) Reviews at the Waste Isolation Pilot Plant (WIPP): Making Complex Information and Decision Making Transparent

International Nuclear Information System (INIS)

Eriksson, Leif G.

2001-01-01

On the 18th of May 1998, based on the information provided by the United Sates Department of Energy (DOE) in support of the 1996 Waste Isolation Pilot Plant (WIPP) Compliance Certification Application, the U.S. Environmental Protection Agency certified the proposed deep geological repository for disposal of long-lived, defense-generated, transuranic radioactive waste at the WIPP site in New Mexico, United States of America, was compliant with all applicable radioactive waste disposal regulations. Seven domestic and one joint international peer reviews commissioned by the DOE were instrumental in making complex scientific and engineering information, as well as the related WIPP decision-making process, both credible and transparent to the majority of affected and interested parties and, ultimately, to the regulator

Expert (Peer) Reviews at the Waste Isolation Pilot Plant (WIPP): Making Complex Information and Decision Making Transparent

Energy Technology Data Exchange (ETDEWEB)

Eriksson, Leif G. [GRAM, Inc., Albuquerque, NM (United States)

2001-07-01

On the 18th of May 1998, based on the information provided by the United Sates Department of Energy (DOE) in support of the 1996 Waste Isolation Pilot Plant (WIPP) Compliance Certification Application, the U.S. Environmental Protection Agency certified the proposed deep geological repository for disposal of long-lived, defense-generated, transuranic radioactive waste at the WIPP site in New Mexico, United States of America, was compliant with all applicable radioactive waste disposal regulations. Seven domestic and one joint international peer reviews commissioned by the DOE were instrumental in making complex scientific and engineering information, as well as the related WIPP decision-making process, both credible and transparent to the majority of affected and interested parties and, ultimately, to the regulator.

Natural analogues for containment-providing barriers for a HLW repository in salt

Energy Technology Data Exchange (ETDEWEB)

Wolf, J.; Noseck, U.

2015-06-15

In 2005, a German research project was started to develop a novel approach to prove safety for a HLW repository in a salt formation, to refine the safety concept, to identify open scientific issues and to define necessary R&D work. This project aimed at identifying the key information for a HLW repository in salt. One important question is how this information may be best fulfilled by natural analogue studies. This question is answered by starting a review of the required key information needs of the safety case (post-closure phase) in order to assess whether or not these requirements can be supported by natural analogues information. In order to structure the review and to address the key elements of the safety concepts, three types of natural analogues are distinguished: (i) natural analogues for the integrity of the geological barrier, (ii) natural analogues for the integrity of the geotechnical barriers and (iii) natural analogues for release scenarios. For the safety case in salt type (i) and (ii) are of highest importance and are treated in this paper. The assessment documented in this paper on the one hand indicates the high potential benefit of natural analogues for a safety case in salt and on the other hand helps to focus the available human and financial resources for the safety case on the most safety-relevant aspects. (authors)

The waste isolation pilot plant: A new regulatory environment

International Nuclear Information System (INIS)

Frei, M.W.; Schneider, S.P.; Saris, E.C.; Austin, P.W.

1993-01-01

The US Department of Energy (DOE) is ready to embark on a multiyear test program, using radioactive waste, at the Waste Isolation Pilot Plant (WIPP). The WIPP is a deep geologic repository, constructed in ancient salt beds in southeastern New Mexico. It was authorized by Congress in 1979 as a research and development facility to demonstrate safe disposal of the nation's defense transuranic (TRU) waste. Nonradioactive testing in the repository has been under way for several years. The DOE is now ready to begin underground experiments at WIPP with small amounts of TRU waste. Radioactive waste testing in an actual repository environment will reduce uncertainties associated with predictions of long-term repository performance. However, the authority for DOE to begin this new phase of the test program no longer resides within the department. The WIPP is now subject to a new level of regulatory oversight by the Environmental Protection Agency (EPA) and other federal agencies, as set forth by Public Law 102-579, the WIPP Land Withdrawal Act, signed by the President on October 30, 1992. This paper discusses the act's new regulatory requirements for WIPP

Corrosion behavior of spent MTR fuel elements in a drowned salt mine repository

International Nuclear Information System (INIS)

Brodda, B.G.; Fachinger, J.

1995-01-01

Spent MTR fuel from German Material Test Reactors will not be reprocessed, but stored in a final salt repository in the deep geologic underground. Fuel elements will be placed in POLLUX containers, which are assumed to resist the corrosive attack of an accidentally formed concentrated salt brine for about 500 years. After a container failure the brine would contact the fuel element, corrode the aluminum plating and possibly leach radionuclides from the fuel. A source term for the calculation of radionuclide mobilization results from the investigation of the behavior of MTR fuel in this scenario, which has to be considered for the long-term safety analysis of a deep mined rock salt repository. Experiments with the different plating materials show that the considered aluminum alloys will not resist the corrosive attack of a brine solution, especially in the presence of iron, under the conditions in a drowned salt mine repository. Although differences in the corrosion rates of about two orders of magnitude were observed when applying different parameter sets, the deterioration must be considered to be almost instantaneous in geological terms. Radionuclides are mobilized from irradiated MTR fuel, when the meat of the fuel element becomes accessible to the brine solution. It seems, however, that the radionuclides are effectively trapped by the aluminum hydroxide formed, as the activity concentrations in the brine solution soon reach a constant level with the progressing corrosion of the cladding aluminum. In the presence of iron a more significant initial release was observed, but also in this case an equilibrium activity seems to be reached as a consequence of radionuclide trapping

Technical developments in the WIPP program

International Nuclear Information System (INIS)

Weart, W.D.

1980-01-01

More than five years of site specific studies have led to the conclusion that radioactive wastes can be safely isolated in the bedded salt of the Delaware Basin in southeast New Mexico. Aspects of particular concern for site integrity, such as regional or local dissolution processes and salt deformation have been thoroughly evaluated and are not believed to present hazards to the repository. Hydrology of the site area has been shown to possess many desirable features with respect to transport of radioisotopes to the bioshpere in the event of a repository breach. Natural resources, potash and hydrocarbons, are present in the area of the site but can be exploited with appropriate precautions. Safety analyses have considered the consequences of their possible attraction to future man. Repository behavior and interactions between waste and the host rock have been studied in the laboratory, in field tests and by calculational methods. In particular, such issues as brine migration and canister corrosion may be shown to have little detrimental impact if modest and practical engineering measures are adopted. Calculations indicate salt deformation and room closure rates may be great enough that a salt repository must be carefully designed in order to assure ready retrieval of emplaced waste over long periods of time. Safety assessment calculations have been performed to determine the consequences of assumed repository failure scenarios. Even the most dire credible (but improbable) natural failure scenarios prove to be benign in their consequences to man. Direct penetration by unknowing, future man could result in significant exposures to the specific individuals involved but would not cause significant population effects

Using TOUGH2 to model the coupled effects of gas generation, repository consolidation, and multiphase brine and gas flow at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Freeze, G.A.; Larson, K.W.; Davies, P.B.; Webb, S.W.

1995-01-01

The Waste Isolation Pilot Plant (WIPP) is a US Department of Energy facility designed to demonstrate the safe underground disposal of transuranic waste. Following waste emplacement, each room will be backfilled with crushed salt. Due to deviatoric stress introduced by excavation, the walls of the waste disposal rooms in the repository will deform over time, consolidating waste containers and salt backfill, thereby decreasing the void volume of the repository. Long-term repository assessment must consider the processes of gas generation, room closure and expansion due to salt creep, and multiphase (brine and gas) fluid flow, as well as the complex coupling between these three processes. Stone (1992) used the mechanical creep closure code SANCHO to simulate the closure of a single, perfectly sealed disposal room filled with waste and backfill. The results of the SANCHO f-series simulations provide a relationship between gas generation, room closure, and room pressure. Several methods for coupling this relationship with multiphase fluid flow into and out of a room were examined by Freeze et al. TOUGH2 was employed to couple the processes of gas generation, room closure/consolidation, and multiphase brine and gas flow. Two empirically-based methods for approximating salt creep and room consolidation were implemented in TOUGH2: the pressure-time-porosity line interpolation approach and the fluid-phase-salt approach. Both approaches utilized links to the SANCHO f-series simulation results to calculate room-void-volume changes with time during a simulation

Mass transfer in a salt repository

International Nuclear Information System (INIS)

Pigford, T.H.; Chambre, P.L.

1985-05-01

To meet regulatory requirements for radioactive waste in a salt repository it is necessary to predict the rates of corrosion of the waste container, the release rates of radionuclides from the waste package, and the cumulative release of radionuclides into the accessible environment. The mechanisms that may control these rates and an approach to predicting these rates from mass-transfer theory are described. This new mechanistic approach is suggested by three premises: (a) a brine inclusion originally in a salt crystal moves along grain boundaries after thermal-induced migration out of the crystal, (b) brine moves along a grain boundary under the influence of a pressure gradient, and (c) salt surrounding a heat-generating waste package will soon creep and consolidate as a monolithic medium surrounding and in contact with the waste package. After consolidation there may be very little migration of intergranular and intragranular brine to the waste package. The corrosion rate of the waste container may then be limited by the rate at which brine reaches the container and may be calculable from mass-transfer theory, and the rate at which dissolved radionuclides leave the waste package may be limited by molecular diffusion in intragranular brine and may be calculable from mass-transfer theory. If porous nonsalt interbeds intersect the waste-package borehole, the release rate of dissolved radionuclides to interbed brine may also be calculable from mass-transfer theory. The logic of these conclusions is described, as an aid in formulating the calculations that are to be made

Radiological consequences of a human intrusion in a nuclear waste repository in a salt formation

International Nuclear Information System (INIS)

Jacquier, P.; Raimbault, P.

1989-07-01

The assessment of the consequences of human intrusion scenarios for a repository is very important for salt formations, since this material has an undeniable economic interest. In this work, the scenario considers the solution mining of salt for human consumption: salt is extracted from a cavern; by leaching, this cavern enlarges and uncovers the waste, which falls down into the sump. It was assumed that the intrusion takes place either 500 years or 2500 years after the closing of the repository. High-level vitrified waste or alpha cemented waste were considered. This paper displays the assumptions made and, using a simplified modelling of the phenomena, the estimation of the radiological consequences due to ingestion of contamined sals. A sensitivity/uncertainty analysis is presented which emphasizes several fields where experimental studies have to be pursued or launched [fr

Evaluation of methods and tools to develop safety concepts and to demonstrate safety for an HLW repository in salt. Final report

Energy Technology Data Exchange (ETDEWEB)

Bollingerfehr, W.; Buhmann, D.; Doerr, S.; and others

2017-03-15

Salt formations have been the preferred option as host rocks for the disposal of high level radioactive waste in Germany for more than 40 years. During this period comprehensive geological investigations have been carried out together with a broad spectrum of concept and safety related R and D work. The behaviour of an HLW repository in salt formations, particularly in salt domes, has been analysed in terms of assessment of the total system performance. This was first carried out for concepts of generic waste repositories in salt and, since 1998, for a repository concept with specific boundary conditions, taking the geology of the Gorleben salt dome as an example. Suitable repository concepts and designs were developed, the technical feasibility has been proven and operational and long-term safety evaluated. Numerical modelling is an important input into the development of a comprehensive safety case for a waste repository. Significant progress in the development of numerical tools and their application for long-term safe ty assessment has been made in the last two decades. An integrated approach has been used in which the repository concept and relevant scientific and engineering data are combined with the results from iterative safety assessments to increase the clarity and the traceability of the evaluation. A safety concept that takes full credit of the favourable properties of salt formations was developed in the course of the R and D project ISIBEL, which started in 2005. This concept is based on the safe containment of radioactive waste in a specific part of the host rock formation, termed the containment providing rock zone, which comprises the geological barrier, the geotechnical barriers and the compacted backfill. The future evolution of the repository system will be analysed using a catalogue of Features, Events and Processes (FEP), scenario development and numerical analysis, all of which are adapted to suit the safety concept. Key elements of the

Evaluation of methods and tools to develop safety concepts and to demonstrate safety for an HLW repository in salt. Final report

International Nuclear Information System (INIS)

Bollingerfehr, W.; Buhmann, D.; Doerr, S.

2017-03-01

Salt formations have been the preferred option as host rocks for the disposal of high level radioactive waste in Germany for more than 40 years. During this period comprehensive geological investigations have been carried out together with a broad spectrum of concept and safety related R and D work. The behaviour of an HLW repository in salt formations, particularly in salt domes, has been analysed in terms of assessment of the total system performance. This was first carried out for concepts of generic waste repositories in salt and, since 1998, for a repository concept with specific boundary conditions, taking the geology of the Gorleben salt dome as an example. Suitable repository concepts and designs were developed, the technical feasibility has been proven and operational and long-term safety evaluated. Numerical modelling is an important input into the development of a comprehensive safety case for a waste repository. Significant progress in the development of numerical tools and their application for long-term safe ty assessment has been made in the last two decades. An integrated approach has been used in which the repository concept and relevant scientific and engineering data are combined with the results from iterative safety assessments to increase the clarity and the traceability of the evaluation. A safety concept that takes full credit of the favourable properties of salt formations was developed in the course of the R and D project ISIBEL, which started in 2005. This concept is based on the safe containment of radioactive waste in a specific part of the host rock formation, termed the containment providing rock zone, which comprises the geological barrier, the geotechnical barriers and the compacted backfill. The future evolution of the repository system will be analysed using a catalogue of Features, Events and Processes (FEP), scenario development and numerical analysis, all of which are adapted to suit the safety concept. Key elements of the

Evolution of hydrologic systems and brine geochemistry in a deforming salt medium: Data from WIPP brine seeps

International Nuclear Information System (INIS)

Deal, D.E.; Roggenthen, W.M.

1991-01-01

The Brine Sampling and Evaluation Program (BSEP) is a formalized continuation of studies that began in 1982 as part of the Site Validation Program. The program was established in 1985. The mission was to document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and the seepage of that brine into the WIPP excavations. This document focuses on the cumulative data obtained from the BSEP. The overall activities of the BSEP described and quantified the brine. It includes documentation and study of brine inflow into boreholes in the facility. The BSEP investigated the occurrence and development of brine weeps, crusts, and brine geochemistry. The presence of salt-tolerant bacteria in the workings was recorded and their possible interactions with experiments and operations, was assessed. The formation properties associated with the occurrence of brine was characterized. The determination of formation properties included the water content of various geologic units, direct examination of these units in boreholes using a video camera system, and measurement of electrical properties relatable to the brine contents. Modeling examined the interaction of salt deformation near the workings and the flow of brine through the deforming rocks. 34 refs

Processes and parameters involved in modeling radionuclide transport from bedded salt repositories. Final report. Technical memorandum

International Nuclear Information System (INIS)

Evenson, D.E.; Prickett, T.A.; Showalter, P.A.

1979-07-01

The parameters necessary to model radionuclide transport in salt beds are identified and described. A proposed plan for disposal of the radioactive wastes generated by nuclear power plants is to store waste canisters in repository sites contained in stable salt formations approximately 600 meters below the ground surface. Among the principal radioactive wastes contained in these canisters will be radioactive isotopes of neptunium, americium, uranium, and plutonium along with many highly radioactive fission products. A concern with this form of waste disposal is the possibility of ground-water flow occurring in the salt beds and endangering water supplies and the public health. Specifically, the research investigated the processes involved in the movement of radioactive wastes from the repository site by groundwater flow. Since the radioactive waste canisters also generate heat, temperature is an important factor. Among the processes affecting movement of radioactive wastes from a repository site in a salt bed are thermal conduction, groundwater movement, ion exchange, radioactive decay, dissolution and precipitation of salt, dispersion and diffusion, adsorption, and thermomigration. In addition, structural changes in the salt beds as a result of temperature changes are important. Based upon the half-lives of the radioactive wastes, he period of concern is on the order of a million years. As a result, major geologic phenomena that could affect both the salt bed and groundwater flow in the salt beds was considered. These phenomena include items such as volcanism, faulting, erosion, glaciation, and the impact of meteorites. CDM reviewed all of the critical processes involved in regional groundwater movement of radioactive wastes and identified and described the parameters that must be included to mathematically model their behavior. In addition, CDM briefly reviewed available echniques to measure these parameters

Conclusions from working group 2 - the analyses of the WIPP-2 experiments

International Nuclear Information System (INIS)

Jackson, C.P.

1995-01-01

The INTRAVAL WIPP-2 test case is based on data from site investigations carried out at the Waste Isolation Pilot Plant (WIPP) in New Mexico, USA. The site has been chosen as a potential location for a radioactive waste repository. Extensive investigations have been carried out, focused mainly on groundwater flow and transport in the Culebra Dolomite, the main pathway for transport of radionuclides off the site by groundwater in the case of an accidental borehole intrusion into the repository. Five teams studied the test case. Two teams addressed issues involved in the treatment of heterogeneity. Stochastic models and a Monte Carlo approach were used. One team quantified the increased uncertainty resulting from fewer data and explored the issues involved in validation of stochastic models. A second team developed a new method for conditioning stochastic models on head data. Two other teams examined issues relating to the choice of conceptual models. Two-dimensional vertical cross-section models were used to explore the importance of vertical flow. The fifth team advocate the use of a variety of models to highlight the most important processes and parameters. Conclusions from each team experiment are analysed. (J.S.). 4 refs., 11 figs

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 8. Repository preconceptual design studies: salt

International Nuclear Information System (INIS)

1978-04-01

This volume, Volume 8 ''Repository Preconceptual Design Studies: Salt,'' is one of a 23-volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provides a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This document describes a preconceptual design for a nuclear waste storage facility in salt. The facility design consists of several chambers excavated deep within a geologic formation together with access shafts and supportive surface structures. The facility design provides for: receiving and unloading waste containers; lowering them down shafts to the mine level; transporting them to the proper storage area, and emplacing them in mined storage rooms. Drawings of the facility design are contained in TM-36/9, ''Drawings for Repository Preconceptual Design Studies: Salt.''

Performance analysis of conceptual waste package designs in salt repositories

International Nuclear Information System (INIS)

Jansen, G. Jr.; Raines, G.E.; Kircher, J.F.

1984-01-01

A performance analysis of commercial high-level waste and spent fuel conceptual package designs in reference repositories in three salt formations was conducted with the WAPPA waste package code. Expected conditions for temperature, stress, brine composition, radiation level, and brine flow rate were used as boundary conditions to compute expected corrosion of a thick-walled overpack of 1025 wrought steel. In all salt formations corrosion by low Mg salt-dissolution brines typical of intrusion scenarios was too slow to cause the package to fail for thousands of years after burial. In high Mg brines judged typical of thermally migrating brines in bedded salt formations, corrosion rates which would otherwise have caused the packages to fail within a few hundred years were limited by brine availability. All of the brine reaching the package was consumed by reaction with the iron in the overpack, thus preventing further corrosion. Uniform brine distribution over the package surface was an important factor in predicting long package lifetimes for the high Mg brines. 14 references, 15 figures

Construction of the thermal/structural interactions in situ tests at the Waste Isolation Pilot Plant (WIPP)

Energy Technology Data Exchange (ETDEWEB)

Munson, D.E.; Matalucci, R.V. [Sandia National Lab., Albuquerque, NM (United States); Hoag, D.L.; Blankenship D.A. [RE/SPEC Inc., Albuquerque, NM (United States)] [and others

1997-02-01

The Department of Energy has constructed the Waste Isolation Pilot Plant (WIPP) to develop the technology for the disposal of radioactive waste from defense programs. Sandia National Laboratories has the responsibility for experimental activities at the WIPP and has emplaced several large-scale Thermal/Structural Interactions (TSI) in situ tests to validate techniques used to predict repository performance. The construction of the tests relied heavily on earlier excavations at the WIPP site to provide a basis for selecting excavation, surveying, and instrumentation methods, and achievable construction tolerances. The tests were constructed within close tolerances to provide consistent room dimensions and accurate placement of gages. This accuracy has contributed to the high quality of data generated which in turn has facilitated the comparison of test results to numerical predictions. The purpose of this report is to detail the construction activities of the TSI tests.

Construction of the thermal/structural interactions in situ tests at the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Munson, D.E.; Matalucci, R.V.; Hoag, D.L.; Blankenship D.A.

1997-02-01

The Department of Energy has constructed the Waste Isolation Pilot Plant (WIPP) to develop the technology for the disposal of radioactive waste from defense programs. Sandia National Laboratories has the responsibility for experimental activities at the WIPP and has emplaced several large-scale Thermal/Structural Interactions (TSI) in situ tests to validate techniques used to predict repository performance. The construction of the tests relied heavily on earlier excavations at the WIPP site to provide a basis for selecting excavation, surveying, and instrumentation methods, and achievable construction tolerances. The tests were constructed within close tolerances to provide consistent room dimensions and accurate placement of gages. This accuracy has contributed to the high quality of data generated which in turn has facilitated the comparison of test results to numerical predictions. The purpose of this report is to detail the construction activities of the TSI tests

Review of Y/OWI/TM-36: repository design performance in salt, granite, shale or basalt

International Nuclear Information System (INIS)

Talbot, R.; Nair, O.B.

1979-09-01

As part of the ongoing work by the Lawrence Livermore Laboratory to evaluate repository design performance, this memorandum presents a review of the preconceptual repository design described in Y/OWI/TM-36, Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations, April 1978. The purpose of this review is: to assess the adequacy of the design procedures and assumptions; to identify inappropriate or unsubstantiated design issues; to identify areas where additional numerical analyses may be required; and to develop data for inclusion in a reference repository design. The preconceptual repository design is presented in the form of 23 volumes of data base, analyses, and design layouts for four rock types: bedded salt, shale, granite and basalt. This memorandum reviews all four repository designs

The development of the Waste Isolation Pilot Plant (WIPP) project's public affairs program

International Nuclear Information System (INIS)

Walter, L.H.

1988-01-01

The Waste Isolation Pilot Plant (WIPP) offers a perspective on the value of designing flexibility into a public affairs program to enable it to grow with and complement a project's evolution from construction through to operations. This paper discusses how the WIPP public affairs program progressed through several stages to its present scope. During the WIPP construction phase, the public affairs program laid a foundation for Project acceptance in the community. A speaker's bureau, a visitors program, and various community outreach and support programs emphasized the educational and socioeconomic benefits of having this controversial project in Carlsbad. Then, in this past year as the project entered a preoperational status, the public affairs program emphasis shifted to broaden the positive image that had been created locally. In this stage, the program promoted the project's positive elements with the various state agencies, government officials, and federal organizations involved in our country's radioactive waste management and transportation program. Currently, an even broader, more aggressive public affairs program is planned. During this stage public affairs will be engaged in a comprehensive institutional and outreach program, explaining and supporting WIPP's mission in each of the communities and agencies affected by the operation of the country's first geologic repository

Chemistry of transuranium elements in salt-base repository

Energy Technology Data Exchange (ETDEWEB)

Borkowski, Marian [Los Alamos National Laboratory; Reed, Donald T [Los Alamos National Laboratory; Lucchini, Jean - Francois [Los Alamos National Laboratory; Richmann, Michael K [Los Alamos National Laboratory; Khaing, H [Los Alamos National Laboratory; Swanson, J [Los Alamos National Laboratory; Ams, D [Los Alamos National Laboratory

2010-12-02

The mobility and potential release of actinides into the accessible environment continues to be the key performance assessment concern of nuclear repositories. Actinide, in particular plutonium speciation under the wide range of conditions that can exist in the subsurface is complex and depends strongly on the coupled effects of redox conditions, inorganic/organic complexation, and the extent/nature of aggregation. Understanding the key factors that define the potential for actinide migration is, in this context, an essential and critical part of making and sustaining a licensing case for a nuclear repository. Herein we report on recent progress in a concurrent modeling and experimental study to determine the speciation of plutonium, uranium and americium in high ionic strength Na-CI-Mg brines. This is being done as part of the ongomg recertification effort m the Waste Isolation Pilot Plant (WIPP). The oxidation-state specific solubility of actinides were established in brine as function of pC{sub H+}, brine composition and the presence and absence of organic chelating agents and carbonate. An oxidation-state invariant analog approach using Nd{sup 3+} and Th{sup 4+} was used for An{sup 3+} and An{sup 4+} respectively. These results show that organic ligands and hydrolysis are key factors for An(III) solubility, hydrolysis at pC{sub H+} above 8 is predominate for An(IV) and carbonates are the key factor for U(VI) solubility. The effect of high ionic strength and brine components measured in absence of carbonates leads to measurable increased in overall solubility over analogous low ionic strength groundwater. Less is known about the bioreduction of actinides by halo-tolerant microorganisms, but there is now evidence that bioreduction does occur and is analogous, in many ways, to what occurs with soil bacteria. Results of solubility studies that focus on Pitzer parameter corrections, new species (e.g. borate complexation), and the thermodynamic parameters for

Performance Assessment of a Generic Repository in Bedded Salt for DOE-Managed Nuclear Waste

Science.gov (United States)

Stein, E. R.; Sevougian, S. D.; Hammond, G. E.; Frederick, J. M.; Mariner, P. E.

2016-12-01

A mined repository in salt is one of the concepts under consideration for disposal of DOE-managed defense-related spent nuclear fuel (SNF) and high level waste (HLW). Bedded salt is a favorable medium for disposal of nuclear waste due to its low permeability, high thermal conductivity, and ability to self-heal. Sandia's Generic Disposal System Analysis framework is used to assess the ability of a generic repository in bedded salt to isolate radionuclides from the biosphere. The performance assessment considers multiple waste types of varying thermal load and radionuclide inventory, the engineered barrier system comprising the waste packages, backfill, and emplacement drifts, and the natural barrier system formed by a bedded salt deposit and the overlying sedimentary sequence (including an aquifer). The model simulates disposal of nearly the entire inventory of DOE-managed, defense-related SNF (excluding Naval SNF) and HLW in a half-symmetry domain containing approximately 6 million grid cells. Grid refinement captures the detail of 25,200 individual waste packages in 180 disposal panels, associated access halls, and 4 shafts connecting the land surface to the repository. Equations describing coupled heat and fluid flow and reactive transport are solved numerically with PFLOTRAN, a massively parallel flow and transport code. Simulated processes include heat conduction and convection, waste package failure, waste form dissolution, radioactive decay and ingrowth, sorption, solubility limits, advection, dispersion, and diffusion. Simulations are run to 1 million years, and radionuclide concentrations are observed within an aquifer at a point approximately 4 kilometers downgradient of the repository. The software package DAKOTA is used to sample likely ranges of input parameters including waste form dissolution rates and properties of engineered and natural materials in order to quantify uncertainty in predicted concentrations and sensitivity to input parameters. Sandia

Scientific, institutional, regulatory, political, and public acceptance of the waste isolation pilot plant transuranic waste repository

International Nuclear Information System (INIS)

Eriksson, L.G.

2000-01-01

The recent successful certification and opening of a first-of-a-kind, deep geological repository for safe disposal of long-lived, transuranic radioactive waste (TRUW) at the Waste Isolation Pilot Plant (WIPP) site, New Mexico, United States of America (USA), embody both long-standing local and wide-spread, gradually achieved, scientific, institutional, regulatory, political, and public acceptance. The related historical background and development are outlined and the main contributors to the successful siting, certification, and acceptance of the WIPP TRUW repository, which may also serve as a model to success for other radioactive waste disposal programs, are described. (author)

Application of molten salt oxidation for the minimization and recovery of plutonium-238 contaminated wastes

International Nuclear Information System (INIS)

Wishau, R.

1998-05-01

Molten salt oxidation (MSO) is proposed as a 238 Pu waste treatment technology that should be developed for volume reduction and recovery of 238 Pu and as an alternative to the transport and permanent disposal of 238 Pu waste to the WIPP repository. In MSO technology, molten sodium carbonate salt at 800--900 C in a reaction vessel acts as a reaction media for wastes. The waste material is destroyed when injected into the molten salt, creating harmless carbon dioxide and steam and a small amount of ash in the spent salt. The spent salt can be treated using aqueous separation methods to reuse the salt and to recover 99.9% of the precious 238 Pu that was in the waste. Tests of MSO technology have shown that the volume of combustible TRU waste can be reduced by a factor of at least twenty. Using this factor the present inventory of 574 TRU drums of 238 Pu contaminated wastes is reduced to 30 drums. Further 238 Pu waste costs of $22 million are avoided from not having to repackage 312 of the 574 drums to a drum total of more than 4,600 drums. MSO combined with aqueous processing of salts will recover approximately 1.7 kilograms of precious 238 Pu valued at 4 million dollars (at $2,500/gram). Thus, installation and use of MSO technology at LANL will result in significant cost savings compared to present plans to transport and dispose 238 Pu TRU waste to the WIPP site. Using a total net present value cost for the MSO project as $4.09 million over a five-year lifetime, the project can pay for itself after either recovery of 1.6 kg of Pu or through volume reduction of 818 drums or a combination of the two. These savings show a positive return on investment

Selection and durability of seal materials for a bedded salt repository: preliminary studies

International Nuclear Information System (INIS)

Roy, D.M.; Grutzeck, M.W.; Wakeley, L.D.

1983-11-01

This report details preliminary results of both experimental and theoretical studies of cementitious seal materials for use in a proposed nuclear waste repository in bedded salt. Effects of changes in bulk composition and environment upon phase stability and physical/mechanical properties have been evaluated for more than 25 formulations. Bonding and interfacial characteristics of the region between host rock and seal material or concrete aggregate and cementitious matrix for selected formulations have been studied. Compatibilities of clays and zeolites in brines typical of the SE New Mexico region have been investigated, and their stabilities reviewed. Results of these studies have led to the conclusion that cementitious materials can be formulated which are compatible with the major rock types in a bedded salt repository environment. Strengths are more than adequate, permeabilities are consistently very low, and elastic moduli generally increase only very slightly with time. Seal formulation guidelines and recommendations for present and future work are presented. 73 references, 25 figures, 61 tables

Summary report for the WIPP [Waste Isolation Pilot Plant] technology development program for isolation of radioactive waste

International Nuclear Information System (INIS)

Tyler, L.D.; Matalucci, R.V.; Molecke, M.A.; Munson, D.E.; Nowak, E.J.; Stormont, J.C.

1988-04-01

The technology experiments have been managed in three broad categories: Thermal/Structural Interactions (TSI), Plugging and Sealing Performance and Design (PandS), and Waste Package Performance (WPP). The history and major progress in each of these areas is summarized in this report. The TSI program has established the fact that the WIPP salt creep rate, and therefore closure of WIPP rooms, is about three times more rapid than our best models predicted prior to the tests. Studies to resolve this discrepancy are well advanced; in the interim, good agreement between predicitions and observation is obtained by empirical adjustment of the elastic constants. The closure of backfilled waste room to about five percent void volume is predicted to take less than 100 years, the time during which active controls may be assumed to prevent human intrusion. The waste package program has revealed that migration of interstitial brine to excavations in the WIPP salt occurs at a significantly greater rate than assumed by earlier investigations. A satisfactory model to explain the data utilizes darcy flow in very low permeability salt which is driven by a pore pressure gradient caused when the excavation creates an atmospheric pressure boundary. This model, coupled with room closure predictions and backfill design using a salt/bentonite clay mixture, indicates that the rate of brine seepage will not result in a fluid or slurry state in the room, but rather in a compacted solid. 373 refs., 20 figs., 9 tabs

Scenarios for long-term release of radionuclides from a nuclear-waste repository in the Los Medanos region of New Mexico

International Nuclear Information System (INIS)

Bingham, F.W.; Barr, G.E.

1979-05-01

This report discusses hypothetical sequences of events that could conceivably release radionuclides from radioactive waste buried in the proposed WIPP repository. All the scenarios are described in terms specific to the WIPP site; they include only events whose occurrence is physically possible there. The report estimates the relative probabilities of the scenarios at times ranging from 1000 to 1 million years after the repository is sealed. Although none of the scenarios is judged likely, the report recommends several for detailed computer modeling and consequence analysis

Evaluation of constitutive models for crushed salt

International Nuclear Information System (INIS)

Callahan, G.D.; Loken, M.C.; Hurtado, L.D.; Hansen, F.D.

1996-01-01

Three constitutive models are recommended as candidates for describing the deformation of crushed salt. These models are generalized to three-dimensional states of stress to include the effects of mean and deviatoric stress and modified to include effects of temperature, grain size, and moisture content. A database including hydrostatic consolidation and shear consolidation tests conducted on Waste Isolation Pilot Plant (WIPP) and southeastern New Mexico salt is used to determine material parameters for the models. To evaluate the capability of the models, parameter values obtained from fitting the complete database are used to predict the individual tests. Finite element calculations of a WIPP shaft with emplaced crushed salt demonstrate the model predictions

Review of geochemical measurement techniques for a nuclear waste repository in bedded salt

International Nuclear Information System (INIS)

Knauss, K.G.; Steinborn, T.L.

1980-01-01

A broad, general review is presented of geochemical measurement techniques that can provide data necessary for site selection and repository effectiveness assessment for a radioactive waste repository in bedded salt. The available measurement techniques are organized according to the parameter measured. The list of geochemical parameters include all those measurable geochemical properties of a sample whole values determine the geochemical characteristics or behavior of the system. For each technique, remarks are made pertaining to the operating principles of the measurement instrument and the purpose for which the technique is used. Attention is drawn to areas where further research and development are needed

Analysis of borehole inclusion stress measurement concepts proposed for use in the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Morgan, H.S.

1984-01-01

The Waste Isolation Pilot Plant (WIPP) is being developed in southeastern New Mexico by the United States Department of Energy as a research and development (RandD) facility to demonstrate the safe disposal in salt of radioactive wastes resulting from defense activities. As part of the WIPP RandD program, a series of in situ tests will be performed to determine the behavior of drifts and storage rooms in the creeping salt medium. Data obtained in these tests will be used to evaluate and improve numerical models used to compute the structural response of these drifts and rooms. Stress has been proposed as one of the parameters to be measured in the tests, and borehole inclusion stressmeters have been included in the instrumentation package

Plutonium interaction with a bacterial strain isolated from the waste isolation pilot plant (WIPP) environment

International Nuclear Information System (INIS)

Strietelmeier, B.A.; Kraus, S.M.; Leonard, P.A.; Triay, I.R.

1996-01-01

This work was conducted as part of a series of experiments to determine the association and interaction of various actinides with bacteria isolated from the WIPP site. The majority of bacteria that exist at the site are expected to be halophiles, or extreme halophiles, due to the high concentration of salt minerals at the location. Experiments were conducted to determine the toxicity of plutonium-n-239, neptunium-237 and americium-243 to several species of these halophiles and the results were reported elsewhere. As an extension of these experiments, we report an investigation of the type of association that occurs between 239 Pu and the isolate WIPP-1A, isolated by staff at Brookhaven National Laboratory, when grown in a high-salt, defined medium. Using scanning electron microscopy (SEM) techniques, we demonstrate a surface association of the 239 Pu with the bacterial cells

Test plan: Potash Core Test. WIPP experimental program borehole plugging

International Nuclear Information System (INIS)

Christensen, C.L.

1979-09-01

The Potash Core Test will utilize a WIPP emplaced plug to obtain samples of an in-situ cured plug of known mix constituents for bench scale testing. An earlier effort involved recovery at the salt horizon of Plug 217, a 17 year old plug in a potash exploration hole for bond testing, but the lack of particulars in the emplacement precluded significant determination of plug performance

Proceedings of the 8th US/German Workshop on Salt Repository Research Design and Operation.

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [RESPEC, Rapid City, SD (United States); Steininger, Walter [Karlsruhe Inst. of Technology (KIT) (Germany); Bollingerfehr, Wilhelm [DBE Technology, Peine (Germany); Kuhlman, Kristopher L [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dunagan, Sean [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-02-01

This document records the Proceedings of the 2017 gathering of salt repository nations. In a spirit of mutual support, technical issues are dissected, led capably by subject matter experts. As before, it is not possible to explore all contemporary issues regarding nuclear waste disposal in salt formations. Instead, the group focused on a few selected issues to be pursued in depth, while at the same time acknowledging and recording ancillary issues.

Repository simulation model: Final report

International Nuclear Information System (INIS)

1988-03-01

This report documents the application of computer simulation for the design analysis of the nuclear waste repository's waste handling and packaging operations. The Salt Repository Simulation Model was used to evaluate design alternatives during the conceptual design phase of the Salt Repository Project. Code development and verification was performed by the Office of Nuclear Waste Isolation (ONWL). The focus of this report is to relate the experience gained during the development and application of the Salt Repository Simulation Model to future repository design phases. Design of the repository's waste handling and packaging systems will require sophisticated analysis tools to evaluate complex operational and logistical design alternatives. Selection of these design alternatives in the Advanced Conceptual Design (ACD) and License Application Design (LAD) phases must be supported by analysis to demonstrate that the repository design will cost effectively meet DOE's mandated emplacement schedule and that uncertainties in the performance of the repository's systems have been objectively evaluated. Computer simulation of repository operations will provide future repository designers with data and insights that no other analytical form of analysis can provide. 6 refs., 10 figs

Coupled modelling of convergence, steel corrosion, gas production and brine flow in a rock salt repository

International Nuclear Information System (INIS)

Becker, D.A.; Hirsekorn, R.P.

2013-01-01

This poster presents the global simulation of the behaviour of thick-walled steel containers piled up in a borehole in a rock salt repository. The simulation takes into account: the convergence by the creeping of rock salt, the backfill and waste compaction, the porosity dependent flow resistance, the anaerobic corrosion (iron to magnetite transformation, gas production, brine consumption, water consumption and salt precipitation) and pressure development. Mechanical influence of corrosion has not yet been taken into account in the integrated code LOPOS

Site selection and evaluation studies of the Waste Isolation Pilot Plant (WIPP), Los Medanos, Eddy County, NM

International Nuclear Information System (INIS)

Griswold, G.B.

1977-12-01

Bedded-salt deposits of the Salado Formation have been selected for evaluation for a proposed Waste Isolation Pilot Plant (WIPP) to be located in Eddy County, NM, approximately 26 mi east of Carlsbad. Site selection and evaluation studies that included geologic mapping, geophysical surveys, drilling, and resource appraisal were conducted over and under the prospective location. The lower portion of the Salado meets essential criteria for waste isolation. Beds chosen for waste storage lie 2074 to 2730 ft below the surface. High-purity salt exists at these depths, and the geologic structure revealed by geophysical surveys indicates that these beds are essentially flat. Additional geophysical surveys are now under way. The initial interpretation of the new data indicates that more structure may exist in the salt beds in the northern portion of the site area. Full evaluation of potentially commercial deposits of potash and natural gas within the WIPP site will be reported by separate studies, as will be the hydrologic details of the region

Thermal Analysis of Disposal of High-Level Nuclear Waste in a Generic Bedded Salt repository using the Semi-Analytical Method.

Energy Technology Data Exchange (ETDEWEB)

Hadgu, Teklu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Matteo, Edward N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

An example case is presented for testing analytical thermal models. The example case represents thermal analysis of a generic repository in bedded salt at 500 m depth. The analysis is part of the study reported in Matteo et al. (2016). Ambient average ground surface temperature of 15°C, and a natural geothermal gradient of 25°C/km, were assumed to calculate temperature at the near field. For generic salt repository concept crushed salt backfill is assumed. For the semi-analytical analysis crushed salt thermal conductivity of 0.57 W/m-K was used. With time the crushed salt is expected to consolidate into intact salt. In this study a backfill thermal conductivity of 3.2 W/m-K (same as intact) is used for sensitivity analysis. Decay heat data for SRS glass is given in Table 1. The rest of the parameter values are shown below. Results of peak temperatures at the waste package surface are given in Table 2.

Modeling of waste/near field interactions for a waste repository in bedded salt: the Dynamic Network (DNET) model

International Nuclear Information System (INIS)

Cranwell, R.M.

1983-01-01

The Fuel Cycle Risk Analysis Division of Sandia National Laboratories has been funded by the US Nuclear Regulatory Commission to develop a methodology for use in assessing the long-term risk from the disposal of radioactive wastes in deep geologic formations. As part of this program, the Dynamic Network (DNET) model was developed to investigate waste/near field interactions associated with the disposal of radioactive wastes in bedded salt formations. The model is a quasi-multi-dimensional network model with capabilities for simulating processes such as fluid flow, heat transport, salt dissolution, salt creep, and the effects of thermal expansion and subsedence on the rock units surrounding the repository. The use of DNET has been demonstrated in the analysis of a hypothetical disposal site containing a bedded salt formation as the host medium for the repository. An example of this demonstration analysis is discussed. Furthermore, the outcome of sensitivity analyses performed on the DNET model are presented

Identification of characteristics which influence repository design domal salt, Task 1. Final report

International Nuclear Information System (INIS)

Rawlings, G.; Antonnen, G.; Chamness, M.

1984-04-01

The purpose of the complete project is to provide NRC with technical assistance to enable the focused, adequate review by NRC of the aspects related to design and construction of an underground test facility and final geologic repository as presented by the Department of Energy (DOE). The study presented in this report covers the identification of characteristics which influence design and construction of a geologic repository in domal salt. This report has identified five key issues, i.e., constructibility, thermal response, mechanical response, hydrologic response, and geochemical response. This report involves both short-term (up to closure) and long-term (post closure) effects. The characteristics of domal salt and its environment are described under the headings of stratigraphic/structural, tectonic, mechanical, thermal and hydrologic. Characteristics are separated into parameters (quantified and measured) and factors (qualitative). The characteristics are then subjectively ranked by their influence on the key issues. This takes into account the availability and suitability of conservative design/construction techniques, uncertainty in model and model sensitivity to the characteristic

Preliminary constitutive properties for salt and nonsalt rocks from four potential repository sites

International Nuclear Information System (INIS)

Pfeifle, T.W.; Mellegard, K.D.; Senseny, P.E.

1983-07-01

Results are presented from laboratory strength and creep tests performed on salt and nonsalt specimens from the Richton Dome in Mississippi, the Vacherie Dome in Louisiana, the Permian Basin in Texas, and the Paradox Basin in Utah. The constititive properties obtained for salt are the elastic moduli and the failure envelope at 24 0 C and parameter values for the exponential-time creep law. Some additional data are presented to indicate how the elastic moduli and strength change with temperature. The nonsalt constitutive properties reported are the elastic moduli, the unconfined compressive strength and the tensile strength at 24 0 C. The properties given in this report will be used in subsequent numerical simulations that will provide information to assist in the screening and selection of site locations for a nuclear waste repository and to assist in the repository design at the selected site. The matrix of tests performed is the minimum effort required to obtain these constitutive properties. The preliminary values obtained will be supplemented by additional testing for sites that are selected for further investigation

Review of the WIPP draft application to show compliance with EPA transuranic waste disposal standards

Energy Technology Data Exchange (ETDEWEB)

Neill, R.H.; Chaturvedi, L.; Clemo, T.M. [and others

1996-03-01

The purpose of the New Mexico Environmental Evaluation Group (EEG) is to conduct an independent technical evaluation of the Waste Isolation Pilot Plant (WIPP) Project to ensure the protection of the public health and safety and the environment. The WIPP Project, located in southeastern New Mexico, is being constructed as a repository for the disposal of transuranic (TRU) radioactive wastes generated by the national defense programs. The EEG was established in 1978 with funds provided by the U.S. Department of Energy (DOE) to the State of New Mexico. Public Law 100-456, the National Defense Authorization Act, Fiscal Year 1989, Section 1433, assigned EEG to the New Mexico Institute of Mining and Technology and continued the original contract DE-AC04-79AL10752 through DOE contract DE-AC04-89AL58309. The National Defense Authorization Act for Fiscal Year 1994, Public Law 103-160, continues the authorization. EEG performs independent technical analyses of the suitability of the proposed site; the design of the repository, its planned operation, and its long-term integrity; suitability and safety of the transportation systems; suitability of the Waste Acceptance Criteria and the generator sites` compliance with them; and related subjects. These analyses include assessments of reports issued by the DOE and its contractors, other federal agencies and organizations, as they relate to the potential health, safety and environmental impacts from WIPP. Another important function of EEG is the independent environmental monitoring of background radioactivity in air, water, and soil, both on-site and off-site.

Review of the WIPP draft application to show compliance with EPA transuranic waste disposal standards

International Nuclear Information System (INIS)

Neill, R.H.; Chaturvedi, L.; Clemo, T.M.

1996-03-01

The purpose of the New Mexico Environmental Evaluation Group (EEG) is to conduct an independent technical evaluation of the Waste Isolation Pilot Plant (WIPP) Project to ensure the protection of the public health and safety and the environment. The WIPP Project, located in southeastern New Mexico, is being constructed as a repository for the disposal of transuranic (TRU) radioactive wastes generated by the national defense programs. The EEG was established in 1978 with funds provided by the U.S. Department of Energy (DOE) to the State of New Mexico. Public Law 100-456, the National Defense Authorization Act, Fiscal Year 1989, Section 1433, assigned EEG to the New Mexico Institute of Mining and Technology and continued the original contract DE-AC04-79AL10752 through DOE contract DE-AC04-89AL58309. The National Defense Authorization Act for Fiscal Year 1994, Public Law 103-160, continues the authorization. EEG performs independent technical analyses of the suitability of the proposed site; the design of the repository, its planned operation, and its long-term integrity; suitability and safety of the transportation systems; suitability of the Waste Acceptance Criteria and the generator sites' compliance with them; and related subjects. These analyses include assessments of reports issued by the DOE and its contractors, other federal agencies and organizations, as they relate to the potential health, safety and environmental impacts from WIPP. Another important function of EEG is the independent environmental monitoring of background radioactivity in air, water, and soil, both on-site and off-site

The Microbiology of Subsurface, Salt-Based Nuclear Waste Repositories: Using Microbial Ecology, Bioenergetics, and Projected Conditions to Help Predict Microbial Effects on Repository Performance

International Nuclear Information System (INIS)

Swanson, Juliet S.; Cherkouk, Andrea; Arnold, Thuro; Meleshyn, Artur; Reed, Donald T.

2016-01-01

This report summarizes the potential role of microorganisms in salt-based nuclear waste repositories using available information on the microbial ecology of hypersaline environments, the bioenergetics of survival under high ionic strength conditions, and ''repository microbiology'' related studies. In areas where microbial activity is in question, there may be a need to shift the research focus toward feasibility studies rather than studies that generate actual input for performance assessments. In areas where activity is not necessary to affect performance (e.g., biocolloid transport), repository-relevant data should be generated. Both approaches will lend a realistic perspective to a safety case/performance scenario that will most likely underscore the conservative value of that case.

The Microbiology of Subsurface, Salt-Based Nuclear Waste Repositories: Using Microbial Ecology, Bioenergetics, and Projected Conditions to Help Predict Microbial Effects on Repository Performance

Energy Technology Data Exchange (ETDEWEB)

Swanson, Juliet S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Cherkouk, Andrea [Helmholtz-Zentrum Dresden-Rossendorf, Rossendorf (Germany); Arnold, Thuro [Helmholtz-Zentrum Dresden-Rossendorf, Rossendorf (Germany); Meleshyn, Artur [Gesellschaft fur Anlagen und Reaktorsicherheit, Braunschweig (Germany); Reed, Donald T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-11-17

This report summarizes the potential role of microorganisms in salt-based nuclear waste repositories using available information on the microbial ecology of hypersaline environments, the bioenergetics of survival under high ionic strength conditions, and “repository microbiology” related studies. In areas where microbial activity is in question, there may be a need to shift the research focus toward feasibility studies rather than studies that generate actual input for performance assessments. In areas where activity is not necessary to affect performance (e.g., biocolloid transport), repository-relevant data should be generated. Both approaches will lend a realistic perspective to a safety case/performance scenario that will most likely underscore the conservative value of that case.

A Single Global Small-User Nuclear Repository

International Nuclear Information System (INIS)

Conca, J.L.; Wright, J.

2009-01-01

Global energy partnerships in nuclear power, proposed by France, Russia, U.S. and England, seek to address the proliferation issue by controlling fuel production and nuclear materials, removing the need for each country to develop enrichment, fabrication, recycling or disposal capabilities. Several of the large generator countries such as France, the U.S., Japan, S. Korea, Russia, the U.K., China and India, all have plans for deep geologic repositories because they anticipate sufficient waste over the next century to justify the expense of a repository. However, countries having, or planning, less than five reactors, such as Egypt, Iran, Indonesia, Brazil and about 30 other countries, will not have sufficient waste generation, or a favorable geologic site, to justify the economic and environmental issues of developing their own repository. The Salado salt formation in New Mexico, set aside for nuclear waste disposal within the 16 square-mile area by the Land Withdrawal Act of 1992, is the most optimal geologic formation for the permanent disposal of any nuclear waste and is easily able to host all of the commercial nuclear waste that will be generated in the next thousand years. The U.S. commercial nuclear waste needs presently surpass all others, and will for the foreseeable future. Hosting the relatively small amount of waste from these small-user nations will add little to U.S. waste stream while the cost/benefit analysis from the standpoint of operations, safety, geology, cost and proliferation is overwhelmingly positive for developing such a global repository. Oceanic and overland transportation, high-level disposal logistics and costs from several programs, including WIPP, have demonstrated that the operation would pay for itself from international user fees with no U.S. taxpayer dollars required and still save the world about $400 billion over 100 years. The ethical considerations alone are compelling. (authors)

Repository site data and information in bedded salt: Palo Duro Basin, Texas

International Nuclear Information System (INIS)

Tien, P.; Nimick, F.B.; Muller, A.B.; Davis, P.A.; Guzowski, R.V.; Duda, L.E.; Hunter, R.L.

1983-11-01

This report is a compilation of data from the literature on the Palo Duro Basin. The Palo Duro Basin is a structural basin, about 150 miles long and 80 miles wide, that is a part of the much larger Permian Basin. The US Department of Energy is investigating the Palo Duro Basin as a potentially suitable area for the site of a repository for the disposal of high-level radioactive waste. Sediments overlying the Precambrian basement range from about 5000 to about 11,000 ft in thickness and from Cambrian to Holocene in age. The strata in the Palo Duro Basin that are of primary interest to the Department of Energy are the bedded salts of the Permian San Andres Formation. The total thickness of the bedded salts is about 2000 ft. The geology of the Palo Duro Basin is well understood. A great deal of information exists on the properties of salt, although much of the available information was not collected in the Palo Duro Basin. Mineral resources are not currently being exploited from the center of the Palo Duro Basin at depth, although the possibility of exploration for and development of such resources can not be ruled out. The continued existence of salts of Permian age indicates a lack of any large amount of circulating ground water. The hydrology of the pre-Tertiary rocks, however, is currently too poorly understood to carry out detailed, site-specific hydrologic modeling with a high degree of confidence. In general, ground water flows from west to east in the Basin. There is little or no hydraulic connection between aquifers above and below the salt sequences. Potable water is pumped from the Ogallala aquifer. Most of the other aquifers yield only nonpotable water. More extensive hydrological data are needed for detailed future modeling in support of risk assessment for a possible repository for high-level waste in the Palo Duro Basin. 464 references

Crushed Salt Constitutive Model

International Nuclear Information System (INIS)

Callahan, G.D.

1999-01-01

The constitutive model used to describe the deformation of crushed salt is presented in this report. Two mechanisms -- dislocation creep and grain boundary diffusional pressure solution -- are combined to form the basis for the constitutive model governing the deformation of crushed salt. The constitutive model is generalized to represent three-dimensional states of stress. Upon complete consolidation, the crushed-salt model reproduces the Multimechanism Deformation (M-D) model typically used for the Waste Isolation Pilot Plant (WIPP) host geological formation salt. New shear consolidation tests are combined with an existing database that includes hydrostatic consolidation and shear consolidation tests conducted on WIPP and southeastern New Mexico salt. Nonlinear least-squares model fitting to the database produced two sets of material parameter values for the model -- one for the shear consolidation tests and one for a combination of the shear and hydrostatic consolidation tests. Using the parameter values determined from the fitted database, the constitutive model is validated against constant strain-rate tests. Shaft seal problems are analyzed to demonstrate model-predicted consolidation of the shaft seal crushed-salt component. Based on the fitting statistics, the ability of the model to predict the test data, and the ability of the model to predict load paths and test data outside of the fitted database, the model appears to capture the creep consolidation behavior of crushed salt reasonably well

Interim performance specifications for conceptual waste-package designs for geologic isolation in salt repositories

International Nuclear Information System (INIS)

1983-06-01

The interim performance specifications and data requirements presented apply to conceptual waste package designs for all waste forms which will be isolated in salt geologic repositories. The waste package performance specifications and data requirements respond to the waste package performance criteria. Subject areas treated include: containment and controlled release, operational period safety, criticality control, identification, and waste package performance testing requirements. This document was generated for use in the development of conceptual waste package designs in salt. It will be revised as additional data, analyses, and regulatory requirements become available

WIPP and the local communities

International Nuclear Information System (INIS)

Krenz, D.L.; Sankey, C.A.

1986-01-01

The Waste Isolation Pilot Plant (WIPP) is located 26 miles southeast of Carlsbad, New Mexico in southeastern New Mexico. Other neighboring communities include Lovington, Hobbs and Loving, New Mexico. In March 1983, the Site and Preliminary Design Validation (SPDV) phase of the project was completed. Full scale facility construction began in July of that year. Overall site construction is scheduled to be complete in December 1986. Construction completion will be followed by pre-operational and safety check-out in 1987, prior to receiving the first nuclear waste which is targeted for receipt on or after October 1988. WIPP has had a significant impact on the local communities. Many local people have been hired by the Department of Energy (DOE), Westinghouse Electric, and U.S. Army Corps of Engineers contractors, as well as associated sub-contractors. As of December 31, 1985, 64% of the 643 people working at WIPP were hired from an 80-mile or less radius of the WIPP site. The majority of local residents support WIPP. As declining potash and mining industries negatively impacted the economic condition of Southeastern New Mexico, WIPP brought jobs and new business opportunities to the area

Critical scientific issues in the demonstration of WIPP compliance with EPA repository standards

International Nuclear Information System (INIS)

Weart, W.D.; Chu, M.S.Y.

1997-01-01

The Department of Energy submitted a Compliance Certification Application for the Waste Isolation Pilot Plant to the Environmental Protection Agency (EPA) in October, 1996. A critical part of this application was a Performance Assessment which predicts the cumulative radioactive release to the accessible environment over a time period of 10,000 years. Comparison of this predicted release to the EPA standard shows a comfortable margin of compliance. The scientific understanding that was critical to developing this assessment spans a broad range of geotechnical disciplines, and required a thorough understanding of the site's geology and hydrology. Evaluation of the geologic processes which are active in the site region establishes that there will be no natural breach of site integrity for millions of years, far longer than the 10,000 year regulatory period. Inadvertent human intrusion is, therefore, the only credible scenario to lead to potential radioactive release to the accessible environment. To substantiate this conclusion and to quantify these potential releases from human intrusion, it has been necessary to develop an understanding of the following processes: (1) salt creep and shaft seal efficacy; (2) gas generation from organic decomposition of waste materials and anoxic corrosion of metals in the waste and waste packages; (3) solubilities for actinides in brine; (4) fluid flow in Salado formation rocks, and (5) hydrologic transport of actinides in the overlying dolomite aquifers. Other issues which had to be evaluated to allow definition of breach scenarios were brine reservoir occurrences and their associated reservoir parameters, consequences of mining over the repository, and drilling for natural resources in the vicinity of the repository. Results of all these studies will be briefly summarized in this paper

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 16. Repository preconceptual design studies: BPNL waste forms in salt

International Nuclear Information System (INIS)

1978-04-01

This volume, Volume 16, ''Repository Preconceptual Design Studies: BPNL Waste Forms in Salt,'' is one of a 23 volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provide a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This document describes a preconceptual design for a nuclear waste storage facility in salt. The waste forms assumed to arrive at the repository were supplied by Battelle Pacific Northwest Laboratories (BPNL). The facility design consists of several chambers excavated deep within a geologic formation together with access shafts and supportive surface structures. The facility design provides for: receiving and unloading waste containers; lowering them down shafts to the mine level; transporting them to the proper storage area and emplacing them in mined storage rooms. Drawings of the facility design are contained in TM-36/17, ''Drawings for Repository Preconceptual Design Studies: BPNL Waste Forms in Salt.''

Mass transport in bedded salt and salt interbeds

International Nuclear Information System (INIS)

Hwang, Y.; Pigford, T.H.; Chambre, P.L.; Lee, W.W.L.

1989-08-01

Salt is the proposed host rock for geologic repositories of nuclear waste in several nations because it is nearly dry and probably impermeable. Although experiments and experience at potential salt sites indicate that salt may contain brine, the low porosity, creep, and permeability of salt make it still a good choice for geologic isolation. In this paper we summarize several mass-transfer and transport analyses of salt repositories. The mathematical details are given in our technical reports

Dessicant materials screening for backfill in a salt repository

International Nuclear Information System (INIS)

Simpson, D.R.

1980-10-01

Maintaining an anhydrous environment around nuclear waste stored in a salt repository is a concern which can be alleviated by using a desiccant material for backfilling. Such a desiccant should desiccate a brine yet be non deliquescent, the hydrated product should have moderate thermal stability, and the desiccant should have a high capacity and be readily available. From a literature search MgO and CaO were identified for detailed study. These oxides, and an intimate mixture of the two obtained by calcining dolomite, were used in experiments to further determine their suitability. They proved to be excellent desiccants with a high water capacity. The hydrates of both have moderate thermal stability and a high water content. Both MgO and CaO react in an alkaline chloride brine forming oxychloride compounds with different waters of crystallization. Some of these compounds are the Sorel Cements. CaO hydrates to Ca(OH) 2 which carbonates with CO 2 in air to form CaCO 3 and release the hydrated water. Thus the intimate mixture of CaO and MgO from calcined dolomite may serve as a desiccant and remove CO 2 from the repository atmosphere

Dessicant materials screening for backfill in a salt repository

Energy Technology Data Exchange (ETDEWEB)

Simpson, D.R.

1980-10-01

Maintaining an anhydrous environment around nuclear waste stored in a salt repository is a concern which can be alleviated by using a desiccant material for backfilling. Such a desiccant should desiccate a brine yet be non deliquescent, the hydrated product should have moderate thermal stability, and the desiccant should have a high capacity and be readily available. From a literature search MgO and CaO were identified for detailed study. These oxides, and an intimate mixture of the two obtained by calcining dolomite, were used in experiments to further determine their suitability. They proved to be excellent desiccants with a high water capacity. The hydrates of both have moderate thermal stability and a high water content. Both MgO and CaO react in an alkaline chloride brine forming oxychloride compounds with different waters of crystallization. Some of these compounds are the Sorel Cements. CaO hydrates to Ca(OH)/sub 2/ which carbonates with CO/sub 2/ in air to form CaCO/sub 3/ and release the hydrated water. Thus the intimate mixture of CaO and MgO from calcined dolomite may serve as a desiccant and remove CO/sub 2/ from the repository atmosphere.

Nuclear waste repository simulation experiments, Asse salt mine, Federal Republic of Germany. Annual report 1984

International Nuclear Information System (INIS)

Rothfuchs, T.; Feddersen, H.K.; Schwarzianeck, P.; Staupendahl, G.; Coyle, A.J.; Eckert, J.; Kalia, H.

1986-07-01

This is the second joint annual report (1984) on experiments simulating a nuclear waste repository at the 800-m (2624-ft) level of the Asse salt mine in the Federal Republic of Germany. This report describes the Asse salt mine, the test equipment, and the pretest properties of the salt in the mine and in the vicinity of the test area. Also included are test data for the first 19 months of operation on the following: brine migration rates, thermal mechanical behavior of the salt (including room closure, stress reading, and thermal profiles), and borehole gas pressures. In addition to field data, laboratory analyses of results are included in this report. The duration of the experiment will be 2 years, ending in December 1985

Final status of the salt repository project waste package program experimental database

International Nuclear Information System (INIS)

Thornton, B.M.; Reimus, P.W.

1988-03-01

This report describes the final status of the Salt Repository Project Waste Package Program Experimental Database. The data base serves as a clearinghouse for all data collected within the Waste Package Program (WPP) and its predecessor programs at Pacific Northwest Laboratory (PNL). The database was maintained using RS/1 database management software. Documented assurance that the entries in the database were consistent with experimental records was provided by having each experimentalist inspect the entries and signify that they were in agreement with the records. The inspection and signoff were done per PNL technical procedures. Data for which it was impossible to obtain the experimentalist's inspection and signature were segregated from the rest of the database, although they could still be accessed by WPP staff. The WPPED contains two groups of subdirectories. One group contains data taken prior to the installation of quality assurance procedures at PNL. The other group of subdirectories contains data taken under the NQA-1 procedures since their installation in April 1985. As part of closeout activities in the Salt Repository Project, the WPP database has been archived onto magnetic media. The data in the database are available by request on magnetic media or in hardcopy form. 2 refs

Sensitivity and uncertainty analysis applied to a repository in rock salt

International Nuclear Information System (INIS)

Polle, A.N.

1996-12-01

This document describes the sensitivity and uncertainty analysis with UNCSAM, as applied to a repository in rock salt for the EVEREST project. UNCSAM is a dedicated software package for sensitivity and uncertainty analysis, which was already used within the preceding PROSA project. The use of UNCSAM provides a flexible interface to EMOS ECN by substituting the sampled values in the various input files to be used by EMOS ECN ; the model calculations for this repository were performed with the EMOS ECN code. Preceding the sensitivity and uncertainty analysis, a number of preparations has been carried out to facilitate EMOS ECN with the probabilistic input data. For post-processing the EMOS ECN results, the characteristic output signals were processed. For the sensitivity and uncertainty analysis with UNCSAM the stochastic input, i.e. sampled values, and the output for the various EMOS ECN runs have been analyzed. (orig.)

WIPP gets thumbs up; Ward Valley time runs out

International Nuclear Information System (INIS)

Anon.

1996-01-01

Legislation passed in late September clears the way for the Department of Energy to begin shipment of national defense transuranic (TRU) radioactive waste to the Waste Isolation Pilot Plant (WIPP), near Carlsbad, NM, as early as November 1997. On September 23, President Clinton signed the Fiscal Year 1997 Defense Authorization Bill, which contained amendments to the 1992 WIPP Land Withdrawal Act. The implementation of the law will help the DOE in its cleanup sites nationwide, and will enhance public health and safety by providing for the disposal of the waste in a 2150-ft underground salt formation, far away from population centers. Key components of the legislation include the following: (1) The US Environmental Protection Agency (EPA) will continue as primary regulator of WIPP. (2) The EPA will have one year to review the Compliance Certification Application, which the DOE was to submit by October 31, 1996. Upon EPA certification (expected in October 1997), the DOE will begin shipping transuranic waste in November 1997. (3) A six-month waiting period for waste shipments has been removed (previously, the DOE was required to wait 180 days after the Energy Secretary's decision to begin disposal operations). (4) New Mexico will receive $20 million immediately, and annually for 14 years, with the funds to be used for infrastructure and road improvements in the state

Application of molten salt oxidation for the minimization and recovery of plutonium-238 contaminated wastes

Energy Technology Data Exchange (ETDEWEB)

Wishau, R.

1998-05-01

Molten salt oxidation (MSO) is proposed as a {sup 238}Pu waste treatment technology that should be developed for volume reduction and recovery of {sup 238}Pu and as an alternative to the transport and permanent disposal of {sup 238}Pu waste to the WIPP repository. In MSO technology, molten sodium carbonate salt at 800--900 C in a reaction vessel acts as a reaction media for wastes. The waste material is destroyed when injected into the molten salt, creating harmless carbon dioxide and steam and a small amount of ash in the spent salt. The spent salt can be treated using aqueous separation methods to reuse the salt and to recover 99.9% of the precious {sup 238}Pu that was in the waste. Tests of MSO technology have shown that the volume of combustible TRU waste can be reduced by a factor of at least twenty. Using this factor the present inventory of 574 TRU drums of {sup 238}Pu contaminated wastes is reduced to 30 drums. Further {sup 238}Pu waste costs of $22 million are avoided from not having to repackage 312 of the 574 drums to a drum total of more than 4,600 drums. MSO combined with aqueous processing of salts will recover approximately 1.7 kilograms of precious {sup 238}Pu valued at 4 million dollars (at $2,500/gram). Thus, installation and use of MSO technology at LANL will result in significant cost savings compared to present plans to transport and dispose {sup 238}Pu TRU waste to the WIPP site. Using a total net present value cost for the MSO project as $4.09 million over a five-year lifetime, the project can pay for itself after either recovery of 1.6 kg of Pu or through volume reduction of 818 drums or a combination of the two. These savings show a positive return on investment.

The waste isolation pilot plant. Permanent isolation of defense transuranic waste in deep geologic salt. A national solution and international model

International Nuclear Information System (INIS)

Franco, Jose; Van Luik, Abraham

2015-01-01

The Waste Isolation Pilot Plant is located about 42 kilometers from the city of Carlsbad, New Mexico. It is an operating deep geologic repository in bedded salt 657 meters below the surface of the Chihuahuan desert. Since its opening in March of 1999, it has received about 12,000 shipments totaling about 91,000 cubic meters of defense related transuranic (TRU) wastes. Twenty-two sites have been cleaned up of their defense-legacy TRU waste. The WIPP's shipping program has an untarnished safety record and its trucks and trailers have safely traveled the equivalent of about 60 round-trips to the Moon. WIPP received, and deserved, a variety of safety accolades over its nearly 15 year working life. In February of 2014, however, two incidents resulted in a major operational suspension and reevaluation of its safety systems, processes and equipment. The first incident was an underground mining truck fire, followed nine days later by an airborne radiation release incident. Accident Investigation Board (AIB) reports on both incidents point to failures of plans, procedures and persons. The AIB recommendations for recovery from both these incidents are numerous and are being carefully implemented. One major recommendation is to no longer have different maintenance and safety requirements for nuclear handling equipment and mining equipment. Maintenance and cleanliness of mining equipment was cited as a contributing cause to the underground fire, and the idea that there can be lesser rigor in taking care of mining equipment, when it is being operated in the same underground space as the waste handling equipment, is not tenable. At some point in the future, the changes made in response to these two incidents will be seen as a valuable lesson learned on behalf of future repository programs. WIPP will once again be seen as a ''pilot'' in the nautical sense, in terms of 'showing the way' - the way to a national and international radioactive waste

The waste isolation pilot plant. Permanent isolation of defense transuranic waste in deep geologic salt. A national solution and international model

Energy Technology Data Exchange (ETDEWEB)

Franco, Jose; Van Luik, Abraham [US Department of Energy, Carlsbad, NM (United States). Carlsbad Field Office

2015-07-01

The Waste Isolation Pilot Plant is located about 42 kilometers from the city of Carlsbad, New Mexico. It is an operating deep geologic repository in bedded salt 657 meters below the surface of the Chihuahuan desert. Since its opening in March of 1999, it has received about 12,000 shipments totaling about 91,000 cubic meters of defense related transuranic (TRU) wastes. Twenty-two sites have been cleaned up of their defense-legacy TRU waste. The WIPP's shipping program has an untarnished safety record and its trucks and trailers have safely traveled the equivalent of about 60 round-trips to the Moon. WIPP received, and deserved, a variety of safety accolades over its nearly 15 year working life. In February of 2014, however, two incidents resulted in a major operational suspension and reevaluation of its safety systems, processes and equipment. The first incident was an underground mining truck fire, followed nine days later by an airborne radiation release incident. Accident Investigation Board (AIB) reports on both incidents point to failures of plans, procedures and persons. The AIB recommendations for recovery from both these incidents are numerous and are being carefully implemented. One major recommendation is to no longer have different maintenance and safety requirements for nuclear handling equipment and mining equipment. Maintenance and cleanliness of mining equipment was cited as a contributing cause to the underground fire, and the idea that there can be lesser rigor in taking care of mining equipment, when it is being operated in the same underground space as the waste handling equipment, is not tenable. At some point in the future, the changes made in response to these two incidents will be seen as a valuable lesson learned on behalf of future repository programs. WIPP will once again be seen as a ''pilot'' in the nautical sense, in terms of 'showing the way' - the way to a national and international radioactive waste

Shaft seals for final high-level radioactive waste repositories. ELSA. Pt. 1

International Nuclear Information System (INIS)

Kudla, W.; Schreiter, F.; Gruner, M.

2013-01-01

The state of the art in science and technology fir shaft seals with long-term stability is summarized regarding their applicability for high-level waste repository in Germany. The concepts and drafts for the shaft sealing systems ERAM, Asse, Konrad, the WIPP side, the RESEAL concept, the NAGRA concept and the project LASA are reviewed. The methodology of applying partial factors in a safety analysis is summarized and the applicability of this method for geotechnical sealing structures is confirmed. To establish geomechanical boundary conditions of the host rocks and clay stone the stress-strain behavior of the rock mass adjoining the shaft has to be identified including time-dependent thermo-mechanical processes. The general and special requirements for the design of shaft sealing systems, especially in salt rock and clay formations are described, derived from the safety requirements (BMU 2010). Finally general information needs were identified.

Conclusions from INTRAVAL working group 3: salt- and clay-related cases

International Nuclear Information System (INIS)

Bogorinski, P.

1995-01-01

A number of countries consider sedimentary rocks to host a nuclear waste repository, the isolation potential of which relies mainly on very low permeabilities of those formations. To establish confidence in models used in future safety assessments, INTRAVAL working group 3 analysed three test cases addressing the relevant processes which govern the transport of radionuclides in the host formation as well as in the overburden. The WIPP 1 test case studied the flow of brine from a bedded salt formation into open excavations under pressure gradients. Experiments carried out at the Waste Isolation Pilot Plant in New Mexico, USA, were carefully analysed and compared to numerical simulations. The Mol test case studied the main transport mechanisms for solutes through clay. Experiments with radioactive tracers were carried out for several years at the Mol underground laboratory, Belgium, and compared to numerical simulations. The Gorleben test case studied the influences of salt leached from a salt dome on the groundwater flow field by density variations. Measurements from a pumping test and of salt content with depth collected at boreholes throughout the investigation area at Gorleben, Germany, were compared with the results of analytical and numerical studies. (J.S.). 8 figs., 1 tab

SRP [Salt Repository Project] configuration management plan

International Nuclear Information System (INIS)

1987-01-01

This configuration management plan describes the organization, policies, and procedures that will be used on the Salt Repository Project (SRP) to implement the configuration management disciplines and controls. Configuration management is a part of baseline management. Baseline management is defined in the SRP Baseline Procedures Notebook and also includes cost and schedule baselines. Configuration management is a discipline applying technical and administrative direction and surveillance to identify and document the functional and physical characteristics of an item, to control changes to those characteristics, to record and report change processing and implementation status, and to audit the results. Configuration management is designed as a project management tool to determine and control baselines, and ensure and document all components of a project interface both physically and functionally. The purpose is to ensure that the product acquired satisfies the project's technical and operational requirements, and that the technical requirements are clearly defined and controlled throughout the development and acquisition process. 5 figs

WIPP conceptual design report. Addendum D. A report to Holmes and Narver, Inc., Anaheim, California on alternative energy sources for Waste Isolation Pilot Plant, Carlsbad, New Mexico

International Nuclear Information System (INIS)

1977-03-01

This report presents the results of a technical and economic analysis of alternative methods of meeting the energy needs of a proposed Waste Isolation Pilot Plant (WIPP) to be located in southeastern New Mexico. The WIPP is a facility for underground storage of radioactive wastes in a deep salt bed. The report analyzes a total of sixteen possible methods for meeting WIPP energy requirements, consisting of purchased electricity and on-site generation in various combinations from full purchased to full on-site

Salt Repository Project site study plan for seismographic monitoring: Revision 1

International Nuclear Information System (INIS)

1987-01-01

This site study plan describes the seismographic monitoring activities to be conducted during the early stages of Site Characterization at the Deaf Smith County site, Texas. The field programs has been designed to provide data useful in addressing information/data needs resulting from Federal/State/local regulatory requirements and repository program requirements. Sixteen new and three relocated seismographic stations will be added to the now existing network of 13 stations for a total of 32 stations in the network. The areal extent is being expanded and selected regions covered more densely to provide more accurate monitoring and location of microearthquakes. More sophisticated instruments are being used at selected locations to allow for more detailed analysis. A few seismographs are being installed at depth to provide a limited 3-D monitoring network in the area of the repository. The Salt Repository Project (SRP) Networks specify the schedule under which the program will operate. The Technique Field Services Contractor (TFSC) is responsible for conducting the field program. Data will be handled and reported in accordance with established SRP procedures. A quality assurance program will be utilized to assure that activities affecting quality are performed correctly and that appropriate documentation is maintained. 32 refs., 11 figs., 4 tabs

The thermo-mechanical behaviour of a salt dome with a heat-generating waste repository

International Nuclear Information System (INIS)

Janssen, L.G.J.; Prij, J.; Kevenaar, J.W.A.M.; Jong, C.J.T.; Klok, J.; Beemsterboer, C.

1984-01-01

This report reviews the analytical work on the disposal of radioactive waste in salt domes performed at ECN in the period 1 January 1980 to 31 December 1982. Chapter 4 in the main report covers the global temperature and deformation analyses of the salt dome and the surrounding rocks. The attached three topical reports cover self-contained parts of the study. The computer program TASTE developed to analyse, at acceptable cost and with, for engineering purposes, sufficient accuracies, the temperature rises in the salt dome due to the stored heat-generating waste is described in Annex 1. Annex 2 gives a description of the extended finite element program GOLIA. The program has been extended to make it suitable for the creep analysis of salt domes with repositories of heat-generating waste. The study on the closing and sealing of boreholes wit heat-generating waste is reported in Annex 3

Bibliography of studies for the Salt Repository Project Office of the Civilian Radioactive Waste Management Program, April 1978-May 1986

International Nuclear Information System (INIS)

1986-10-01

DOE/CH/10140-05 is an annotated bibliography of approved reports that have been produced for the US Department of Energy Salt Repository Project Office of the Civilian Radioactive Waste Management Program since April 1978. This document is intended for use by the US Department of Energy, State and local officials, the US Nuclear Regulatory Commission, contractors to the Office of Nuclear Waste Isolation, concerned citizens, and others who need a comprehensive listing of reports related to a nuclear waste repository in salt. This document consists of a main report listing, appendixes with Work Breakdown Structure lists, and a topical index

Bibliography of studies for the Salt Repository Project Office of the Civilian Radioactive Waste Management Program, April 1978-December 1986

International Nuclear Information System (INIS)

1987-06-01

This document is an annotated bibliography of approved reports that have been produced for the US Department of Energy Salt Repository Project Office of the Civilian Radioactive Waste Management Program since April 1978. This document is intended for use by the US Department of Energy, State and local officials, the US Nuclear Regulatory Commission, contractors to the Office of Nuclear Waste Isolation, concerned citizens, and others who need a comprehensive listing of reports related to a nuclear waste repository in salt. This document consists of a main report listing, appendixes with Work Breakdown Structure lists, and a topical index

Waste isolation pilot plant disposal room model

Energy Technology Data Exchange (ETDEWEB)

Butcher, B.M.

1997-08-01

This paper describes development of the conceptual and mathematical models for the part of the Waste Isolation Pilot Plant (WIPP) repository performance assessment that is concerned with what happens to the waste over long times after the repository is decommissioned. These models, collectively referred to as the {open_quotes}Disposal Room Model,{close_quotes} describe the repository closure process during which deformation of the surrounding salt consolidates the waste. First, the relationship of repository closure to demonstration of compliance with the Environmental Protection Agency (EPA) standard (40 CFR 191 Appendix C) and how sensitive performance results are to it are examined. Next, a detailed description is provided of the elements of the disposal region, and properties selected for the salt, waste, and other potential disposal features such as backfill. Included in the discussion is an explanation of how the various models were developed over time. Other aspects of closure analysis, such as the waste flow model and method of analysis, are also described. Finally, the closure predictions used in the final performance assessment analysis for the WIPP Compliance Certification Application are summarized.

Waste isolation pilot plant disposal room model

International Nuclear Information System (INIS)

Butcher, B.M.

1997-08-01

This paper describes development of the conceptual and mathematical models for the part of the Waste Isolation Pilot Plant (WIPP) repository performance assessment that is concerned with what happens to the waste over long times after the repository is decommissioned. These models, collectively referred to as the open-quotes Disposal Room Model,close quotes describe the repository closure process during which deformation of the surrounding salt consolidates the waste. First, the relationship of repository closure to demonstration of compliance with the Environmental Protection Agency (EPA) standard (40 CFR 191 Appendix C) and how sensitive performance results are to it are examined. Next, a detailed description is provided of the elements of the disposal region, and properties selected for the salt, waste, and other potential disposal features such as backfill. Included in the discussion is an explanation of how the various models were developed over time. Other aspects of closure analysis, such as the waste flow model and method of analysis, are also described. Finally, the closure predictions used in the final performance assessment analysis for the WIPP Compliance Certification Application are summarized

Special features of nuclear waste repository ventilation system VIS-A-VIS experiences at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Sethi, S.C.

1991-01-01

The paper presents an analysis and discussion of the underground ventilation system at the Waste Isolation Pilot Plant (WIPP). Particular emphasis is placed on specific repository-related requirements and the gradual evolution of engineering designs relative to the WIPP Project scope. The ventilation system for a nuclear waste facility similar to WIPP is designed to provide a suitable environment for personnel and equipment during normal activities. It is also designed to provide confinement and channeling of potential airborne radioactive material in the event of an accidental release. It is desirable to identify and design all parallel activities and the required process equipment prior to completion of the repository mine final design. Such factors as ventilation requirements, drift sizes, bulkhead sizes, and placement are dependent on these items. Mine creep closure properties must be factored into the mine and ventilation equipment design considerations. Effects of natural ventilation pressures deserve due consideration in the design. Mine ventilation requirements are dominated by the diesel equipment to be operated in the underground horizon. WIPP engineers have also found it extremely desirable to have automated real-time monitoring and control for the underground ventilation air. Final testing and balancing of the ventilation system is an extremely important startup requirement. 3 refs., 2 figs

Systems engineering management plan for the Salt Repository Project

International Nuclear Information System (INIS)

Neff, J.O.

1986-08-01

This document presents the plan for using systems engineering in conducting and managing the technical work of the Salt Repository Project (SRP) of the US Department of Energy's Civilian Radioactive Waste Management Program. The need for preparing a Systems Engineering Management Plan (SEMP) is traced back to relevant DOE directives. These directives are interpreted as SRP requirements in the context of the Mined Geologic Disposal System. The strategy for conducting systems engineering on the SRP, including the role of the systems engineering process, is then described. The SEMP also designates who in the project organization will be responsible for carrying out the activities. Finally, the management tools that are used to implement the systems engineering process, including associated documentation on the SRP, are described

National waste terminal storage repository in a bedded salt formation for spent unreprocessed fuel. Volume I. Conceptual design report

International Nuclear Information System (INIS)

1978-12-01

In February 1976, the Energy Research and Development Administration (ERDA), now the Department of Energy (DOE), established a National Waste Terminal Storage (NWTS) program. As a part of this program, two parallel conceptual design efforts were initiated in January 1977. One was for deep geologic storage, in domed salt, of high level waste resulting from the reprocessing of spent fuel. The other was for deep geologic storage of unreprocessed spent fuel in bedded salt. These two concepts are identified as NWTS Repository 1 and Repository 2, respectively. Repository 2 (NWTSR2) is the concept which is covered by this Conceptual Design Report. Volume I of the conceptual design report contains the following information: physical description of the report; project purpose and justification; principal safety, fire, and health hazards; environmental impact considerations; quality assurance considerations; assessment of operational interfaces; assessment of research and development interfaces; project schedule; proposed method of accomplishment; summary cost estimate; and outline specifications. The conceptual design for Repository 2 was developed in sufficient detail to permit determination of scope, engineering feasibility, schedule, and cost estimates, all of which are necessary for planning and budgeting the project

Uncertainty and sensitivity analysis for two-phase flow in the vicinity of the repository in the 1996 performance assessment for the Waste Isolation Pilot Plant: Disturbed conditions

International Nuclear Information System (INIS)

HELTON, JON CRAIG; BEAN, J.E.; ECONOMY, K.; GARNER, J.W.; MACKINNON, ROBERT J.; MILLER, JOEL D.; SCHREIBER, J.D.; VAUGHN, PALMER

2000-01-01

Uncertainty and sensitivity analysis results obtained in the 1996 performance assessment (PA) for the Waste Isolation Pilot Plant (WIPP) are presented for two-phase flow in the vicinity of the repository under disturbed conditions resulting from drilling intrusions. Techniques based on Latin hypercube sampling, examination of scatterplots, stepwise regression analysis, partial correlation analysis and rank transformations are used to investigate brine inflow, gas generation repository pressure, brine saturation and brine and gas outflow. Of the variables under study, repository pressure and brine flow from the repository to the Culebra Dolomite are potentially the most important in PA for the WIPP. Subsequent to a drilling intrusion repository pressure was dominated by borehole permeability and generally below the level (i.e., 8 MPa) that could potentially produce spallings and direct brine releases. Brine flow from the repository to the Culebra Dolomite tended to be small or nonexistent with its occurrence and size also dominated by borehole permeability

Key Geomechanics Issues at the Waste Isolation Pilot Plant Geomechanics

International Nuclear Information System (INIS)

HANSEN, FRANCIS D.

1999-01-01

Mechanical and hydrological properties of rock salt provide excellent bases for geological isolation of hazardous materials. Regulatory compliance determinations for the Waste Isolation Pilot Plant (WIPP) stand as testament to the widely held conclusion that salt provides excellent isolation properties. The WIPP saga began in the 1950s when the U.S. National Academy of Sciences (NAS) recommended a salt vault as a promising solution to the national problem of nuclear waste disposal. For over 20 years, the Scientific basis for the NAS recommendation has been fortified by Sandia National Laboratories through a series of large scale field tests and laboratory investigations of salt properties. These scientific investigations helped develop a comprehensive understanding of salt's 4 reformational behavior over an applicable range of stresses and temperatures. Sophisticated constitutive modeling, validated through underground testing, provides the computational ability to model long-term behavior of repository configurations. In concert with advancement of the mechanical models, fluid flow measurements showed not only that the evaporite lithology was essentially impermeable but that the WIPP setting was hydrologically inactive. Favorable mechanical properties ensure isolation of materials placed in a salt geological setting. Key areas of the geomechanics investigations leading to the certification of WIPP are in situ experiments, laboratory tests, and shaft seal design

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

Energy Technology Data Exchange (ETDEWEB)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-11-15

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

International Nuclear Information System (INIS)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-01-01

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Effects of temperature, temperature gradients, stress, and irradiation on migration of brine inclusions in a salt repository

International Nuclear Information System (INIS)

Jenks, G.H.

1979-07-01

Available experimental and theoretical information on brine migration in bedded salt are reviewed and analyzed. The effects of temperature, thermal gradients, stress, irradiation, and pressure in a salt repository are among the factors considered. The theoretical and experimental (with KCl) results of Anthony and Cline were used to correlate and explain the available data for rates of brine migration at temperatures up to 250 0 C in naturally occurring crystals of bedded salt from Lyons and Hutchinson, Kansas. Considerations of the effects of stressing crystals of bedded salt on the migratin properties of brine inclusions within the crystals led to the conclusion that the most probable effects are a small fractional increase in the solubility of the salt within the liquid and a concomitant and equal fractional increase in the rate of the thermal gradient-induced migration of the brine. The greatest uncertainty relative to the prediction of rates of migration of brine into a waste emplacement cavity in bedded salt is associated with questions concerning the effects of the grain boundaries (within the aggregates of single crystals which comprise a bedded salt deposit) on brine migration through the deposit. The results of some of the estimates of rates and total amounts of brine inflow to HLW and SURF waste packages emplaced in bedded salt were included to illustrate the inflow volumes which might occur in a repository. The results of the brine inflow estimates for 10-year-old HLW emplaced at 150 kW/acre indicated inflow rates starting at 0.7 liter/year and totaling 12 liters at 30 years after emplacement. The results of the estimates for 10-year-old PWR SURF emplaced at 60 kW/acre indicated a constant inflow of 0.035 liter/year for the first 35 years after emplacement

Identification of release scenarios for a repository of radioactive waste in a salt dome in the Netherlands

International Nuclear Information System (INIS)

Glasbergen, P.; Hamstra, J.

1981-01-01

A review is presented of the long-term scenarios used in the safety analysis which was carried out for the disposal of radioactive waste in salt domes in the Netherlands. The long-term analysis involved the following natural processes or events: climatological and sea-level changes, glacial erosion, diapirism, subsidence, faulting and dissolution. The model calculations which were carried out showed the dominant parameters: the rate of diapirism and the rate of subsurface dissolution of rock salt. During the operational period the intrusion of water in the repository was considered to be the most hazardous event. Because the layout of the disposal mine, the disposal geometry and the disposal mining procedures were still under consideration, the first approach of a release scenario was made on a generic basis. A generic scenario is presented for the events during the flooding of the repository. The transport ways of water through the repository and its surroundings are indicated. It is concluded that release scenario analysis for long-term periods and for the operational period provides essential information to optimize the overall disposal system in an iterative process

Key Past and Present Hydrologic Issues at the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Lappin, Allen R.; McKenna, Sean A.; Davies, Peter B.

2000-01-01

In May 1998, the U.S; Environmental Protection Agency (EPA) certified the U.S. Department of Energy's (DOE) Waste Isolation Pilot Plant (WIPP) to be in compliance with applicable portions of regulations governing the permanent disposal of radioactive wastes. The step was accomplished after 24 years of effort by Sandia National Laboratories, extending from initial site selection, through extensive site characterization and under-ground experimentalization to evaluation and demonstration of regulatory compliance. The strong focus on regulatory compliance extended over approximately five years, culminating in DOE's submittal of a Compliance Certification Application (CCA) in October, 1996. Specific lessons learned from the WIPP'S transition from site characterization/experimental research to a successful regulatory compliance application may be of general interest to participants in other repository problems. In summary, the three examples considered in this paper indicate that: It is critical that site-characterization and performance-assessment (PA) activities in a repository project advance through multiple iterative interactions. This is because there are parallel paths of evolution-within a projecy On one hand, there is a natural development in the conceptual understanding of the site and repository geology, hydrology, and geochemistry over time, as well as a normal increase in the roles of regulatory/safety issues relative to technical issues. On the other hand there is ongoing evolution in numerical-modeling, experimental, and PA techniques, as well as in understanding of the insights gained from these activities. However, even if conceptual models do not change, the modeling and documentation techniques and detailed logic supporting these models will change; as additional relevant information is collected within or outside the project. Some issues related to general site-characterization or site-suitability will remain of interest, even after initial

Design and construction issues associated with sealing of a repository in salt

International Nuclear Information System (INIS)

Cook, R.

1991-01-01

The isolation of radioactive wastes in geologic repositories requires that man-made penetrations such as shafts, tunnels and boreholes are adequately sealed. This paper presents the current design and construction issues for sealing a repository in salt and outlines some proposed solutions. The sealing components include shaft seals, tunnel seals, panel seals, and disposal room backfill. The performance requirements and construction constraints determine the types of materials selected and their necessary properties. The current issues of interest include: (1) selection of materials for rigid bulkheads used to promote recovery of the disturbed zone permeability; (2) the selection of bulkhead geometry to cutoff flow through more permeable zones, or zones where recovery of the backfill properties occurs more slowly or not at all; and (3) the interaction of fluids with hazardous wastes with brine and, subsequently, with seal materials that might affect seal material longevity. 19 refs., 5 figs., 1 tab

Solubility and sorption characteristics of uranium(VI) associated with rock samples and brines/groundwaters from WIPP and NTS

International Nuclear Information System (INIS)

Dosch, R.G.

1981-01-01

Solubility measurements for U(VI) in WIPP-related brines/groundwaters were made using initial U(VI) concentrations in the range of 1 to 50 μg/ml. Distribution coefficients (Kd) for U(VI) were determined for Culebra and Magenta dolomites using four different brine/groundwater compositions and for argillaceous shale and hornfels samples from the Eleana and Calico Hills Formation on NTS using a groundwater simulant typical of that area. The Kd's were evaluated as functions of: (1) U(VI) concentration (1.4 x 10 -4 to 1.4 μg/ml); (2) solution volume-to-rock mass ratios used in the measurements (5 to 100 ml/g), and for WIPP material only; (3) water composition (0 to 100% brine in groundwater); and (4) sample location in the Culebra and Magenta dolomite members of the Rustler Formation. The results indicate that if groundwater intrudes into a repository and leaches a waste form, significant concentrations of dissolved or colloidal U(VI) could be maintained in the liquid phase. Should these solutions enter an aquifer system, there are reasonable sets of conditions which could lead to subsequent migration of U(VI) away from the repository site

GRS/ISTec strategy for the treatment of gas-related issues for repositories located in rock salt

International Nuclear Information System (INIS)

Muller-Lyda, I.; Javeri, V.; Muller, W.

2001-01-01

The treatment of gas-related issues for repositories located in rock salt by GRS and ISTec has followed a strategy which has been developed with increasing complexity and degree of detail in the past. The strategy today clearly indicates the direction to establish a comprehensive safety case and the work that remains to be done. For gas generation mainly long-term aspects are an issue to increase accuracy of predictions. Physical modelling especially for HLW is still incomplete with regard to the coupling of fluid flow with geomechanics, solution/precipitation effects and geochemistry. The appropriate tools to transform the physical models into numerical solutions are at hand in principle but have to be further developed collaterally to the physical modelling. The first full-scale demonstration of safety regarding gas issues in rock salt will have to be provided for the licensing of the Morsleben repository shut-down in the near future. (authors)

Potential release scenario and radiological consequence evaluation of mineral resources at WIPP

International Nuclear Information System (INIS)

Little, M.S.

1982-05-01

This report has reviewed certain of the natural resources which may be found at the site of the nuclear waste repository being considered for southeastern New Mexico, and discussed the scenarios which have been used to estimate the radiological consequences from the mining of these resources several hundred years after the radioactive waste has been emplaced. It has been concluded that the radiological consequences of the mining of potash or hydrocarbons (mostly natural gas) are probably bounded by the consequences of hydrologic breach scenarios already considered by the US Department of Energy, and by reports of EEG. These studies conclude that the resultant doses would not constitute a significant threat to public health. This report also evaluates the radiological consequences of solution mining of halite at the WIPP site. Although such mining in the Delaware Basin and particularly at the WIPP site, is not likely at the present time, significant economic, social or climatic changes a few hundred years after emplacement may make these resources more attractive. The DOE did not consider such mining at the site credible

Design of repository sealing systems - 1981

International Nuclear Information System (INIS)

Ellison, R.D.; Shukla, D.K.; Kelsall, P.C.; D'Appolonia Consulting Engineers, Albuquerque, NM)

1982-01-01

Isolating nuclear waste in geologic repositories will require the sealing of penetrations such as access shafts and tunnels, disposal rooms, and exploration boreholes. This paper discusses seal designs developed for a repository in bedded salt referenced to the stratigraphy of southeastern New Mexico. Designs are based on a multiple component concept whereby individual components are designed for a specific function and location. For a repository in salt the major function of the seals is to exclude groundwater inflow. Two main types of component are included for this purpose: (1) bulk-heads are dense concrete structures keyed into the walls of the penetration and are intended to reduce flow at the interface between the seal and the salt; (2) backfills are granular materials compacted in place in the penetration. In the repository the major backfill material is crushed salt, which is expected to consolidate and recrystallize as the rooms close in response to salt creep. Densely compacted clays will be used as backfill in the shafts closer to potential sources of water inflow. 22 references, 10 figures, 1 table

WIPP Project Records Management Handbook

International Nuclear Information System (INIS)

1991-01-01

The Waste Isolation Pilot Plant (WIPP) Records Management Handbook provides the WIPP Project Records Management personnel with a tool to use to fulfill the requirements of the WIPP Records Program and direct their actions in the important area of records management. The handbook describes the various project areas involved in records management, and how they function. The handbook provides the requirements for Record Coordinators and Master Record Center (MRC) personnel to follow in the normal course of file management, records scheduling, records turnover, records disposition, and records retrieval. More importantly, the handbook provides a single reference which encompasses the procedures set fourth in DOE Order 1324.2A, ''Records Disposition'' ASME NQA-1, ''Quality Assurance Program Requirements for Nuclear Facilities'' and DOE-AL 5700.6B, ''General Operations Quality Assurance.'' These documents dictate how an efficient system of records management will be achieved on the WIPP Project

Blending mining and nuclear industries at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Walls, J.R.

1990-01-01

At the Waste Isolation Pilot Plant (WIPP) traditional procedures for underground mining activities have been significantly altered in order to assure underground safety and project adherence to numerous regulatory requirements. Innovative techniques have been developed for WIPP underground procedures, mining equipment, and operating environments. The mining emphasis at WIPP is upon the quality of the excavation, not (as in conventional mines) on the production of ore. The WIPP is a United States Department of Energy (DOE) project that is located 30 miles southeast of Carlsbad, New Mexico, where the nation's first underground engineered nuclear repository is being constructed. The WIPP site was selected because of its location amidst a 607 meter thick salt bed, which provides a remarkably stable rock formation for the permanent storage of nuclear waste. The underground facility is located 655 meters below the earth's surface, in the Salado formation, which comprises two-hundred million year old halites with minor amounts of clay and anhydrites. When completed, the WIPP underground facility will consist of two components: approximately 81 square kilometers of experimental areas, and approximately 405 square kilometers of repository. 3 figs

INTRAVAL Phase 2 WIPP 1 test case report: Modeling of brine flow through halite at the Waste Isolation Pilot Plant site

International Nuclear Information System (INIS)

Beauheim, R.L.

1997-05-01

This report describes the WIPP 1 test case studied as part of INTRAVAL, an international project to study validation of geosphere transport models. The WIPP 1 test case involved simulation of measured brine-inflow rates to boreholes drilled into the halite strata surrounding the Waste Isolation Pilot Plant repository. The goal of the test case was to evaluate the use of Darcy's law to describe brine flow through halite. The general approach taken was to try to obtain values of permeability and specific capacitance that would be: (1) consistent with other available data and (2) able to provide reasonable simulations of all of the brine-inflow experiments performed in the Salado Formation. All of the teams concluded that the average permeability of the halite strata penetrated by the holes was between approximately 10 -22 and 10 -21 m 2 . Specific capacitances greater than 10 -10 Pa -1 are inconsistent with the known constitutive properties of halite and are attributed to deformation, possibly ongoing, of the halite around the WIPP excavations. All project teams found that Darcy-flow models could replicate the experimental data in a consistent and reasonable manner. Discrepancies between the data and simulations are attributed to inadequate representation in the models of processes modifying the pore-pressure field in addition to the experiments themselves, such as ongoing deformation of the rock around the excavations. Therefore, the conclusion from the test case is that Darcy-flow models can reliably be used to predict brine flow to WIPP excavations, provided that the flow modeling is coupled with measurement and realistic modeling of the pore-pressure field around the excavations. This realistic modeling of the pore-pressure field would probably require coupling to a geomechanical model of the stress evolution around the repository

Representation of two-phase flow in the vicinity of the repository in the 1996 performance assessment for the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

VAUGHN, PALMER; BEAN, J.E.; HELTON, JON CRAIG; LORD, MICHAEL E.; MACKINNON, ROBERT J.; SCHREIBER, JAMES D.

2000-01-01

The following topics related to the representation of two-phase (gas and brine) flow in the vicinity of the repository in the 1996 performance assessment (PA) for the Waste Isolation Pilot Plant (WIPP) are discussed: (1) system of nonlinear partial differential equations used to model two-phase flow, (2) incorporation of repository shafts into model (3) creep closure of repository. (4) interbed fracturing, (5) gas generation (6) capillary action in waste, (7) borebole model (8) numerical solution and (9) gas and brine flow across specified boundaries. Two-phase flow calculations are a central part of the 1996 WIPP PA and supply results that are subsequently used in the calculation of releases to the surface at the time of a drilling intrusion (i.e., spallings, direct brine releases) and long-term releases due to radionuclide transport by flowing groundwater

WIPP/SRL in-situ tests

International Nuclear Information System (INIS)

Mamsey, W.G.

1990-01-01

The Materials Interface Interactions Test (MIIT) is the only in-situ program involving the burial of simulated high-level waste forms operating in the United States. Fifteen glass and waste form compositions and their proposed package materials, supplied by 7 countries, are interred in salt at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. A joint effort between Sandia National Laboratories and Savannah River Laboratory, MIIT is the largest international cooperative in-situ venture yet undertaken. The objective of the current study is to document the waste form compositions used in the MIIT program and then to examine compositional correlations based on structural considerations, bonding energies, and surface layer formation. These correlations show important similarities between the many different waste glass compositions studied world wide and suggest that these glasses would be expected to perform well and in a similar manner

Groundwater recharge and discharge scenarios for a nuclear waste repository in bedded salt

International Nuclear Information System (INIS)

Carpenter, D.W.; Steinborn, T.L.; Thorson, L.D.

1979-01-01

Twelve potential scenarios have been identified whereby groundwater may enter or exit a nuclear waste repository in bedded salt. The 12 scenarios may be grouped into 4 categories or failure modes: dissolution, fracturing, voids, and penetration. Dissolution modes include breccia pipe and breccia blanket formation, and dissolution around boreholes. Fracture modes include flow through preexisting or new fractures and the effects of facies changes. Voids include interstitial voids (pores) and fluid inclusions. Penetration modes include shaft and borehole sealing failures, undetected boreholes, and new mines or wells constructed after repository decommissioning. The potential importance of thermal effects on groundwater flow patterns and on the recharge-discharge process is discussed. The appropriate levels of modeling effort, and the interaction between the adequacy of the geohydrologic data base and the warranted degree of model complexity are also discussed

Radioactive waste isolation in salt: special advisory report on the status of the Office of Nuclear Waste Isolation's plans for repository performance assessment

International Nuclear Information System (INIS)

Ditmars, J.D.; Walbridge, E.W.; Rote, D.M.; Harrison, W.; Herzenberg, C.L.

1983-10-01

Repository performance assessment is analysis that identifies events and processes that might affect a repository system for isolation of radioactive waste, examines their effects on barriers to waste migration, and estimates the probabilities of their occurrence and their consequences. In 1983 Battelle Memorial Institute's Office of Nuclear Waste Isolation (ONWI) prepared two plans - one for performance assessment for a waste repository in salt and one for verification and validation of performance assessment technology. At the request of the US Department of Energy's Salt Repository Project Office (SRPO), Argonne National Laboratory reviewed those plans and prepared this report to advise SRPO of specific areas where ONWI's plans for performance assessment might be improved. This report presents a framework for repository performance assessment that clearly identifies the relationships among the disposal problems, the processes underlying the problems, the tools for assessment (computer codes), and the data. In particular, the relationships among important processes and 26 model codes available to ONWI are indicated. A common suggestion for computer code verification and validation is the need for specific and unambiguous documentation of the results of performance assessment activities. A major portion of this report consists of status summaries of 27 model codes indicated as potentially useful by ONWI. The code summaries focus on three main areas: (1) the code's purpose, capabilities, and limitations; (2) status of the elements of documentation and review essential for code verification and validation; and (3) proposed application of the code for performance assessment of salt repository systems. 15 references, 6 figures, 4 tables

Waste package/repository impact study: Final report

Energy Technology Data Exchange (ETDEWEB)

1985-09-01

The Waste Package/Repository Impact Study was conducted to evaluate the feasibility of using the current reference salt waste package in the salt repository conceptual design. All elements of the repository that may impact waste package parameters, i.e., (size, weight, heat load) were evaluated. The repository elements considered included waste hoist feasibility, transporter and emplacement machine feasibility, subsurface entry dimensions, feasibility of emplacement configuration, and temperature limits. The evaluations are discussed in detail with supplemental technical data included in Appendices to this report, as appropriate. Results and conclusions of the evaluations are discussed in light of the acceptability of the current reference waste package as the basis for salt conceptual design. Finally, recommendations are made relative to the salt project position on the application of the reference waste package as a basis for future design activities. 31 refs., 11 figs., 11 tabs.

Waste package/repository impact study: Final report

International Nuclear Information System (INIS)

1985-09-01

The Waste Package/Repository Impact Study was conducted to evaluate the feasibility of using the current reference salt waste package in the salt repository conceptual design. All elements of the repository that may impact waste package parameters, i.e., (size, weight, heat load) were evaluated. The repository elements considered included waste hoist feasibility, transporter and emplacement machine feasibility, subsurface entry dimensions, feasibility of emplacement configuration, and temperature limits. The evaluations are discussed in detail with supplemental technical data included in Appendices to this report, as appropriate. Results and conclusions of the evaluations are discussed in light of the acceptability of the current reference waste package as the basis for salt conceptual design. Finally, recommendations are made relative to the salt project position on the application of the reference waste package as a basis for future design activities. 31 refs., 11 figs., 11 tabs

WASTE ISOLATION PILOT PLANT (WIPP): THE NATIONS' SOLUTION TO NUCLEAR WASTE STORAGE AND DISPOSAL ISSUES

Energy Technology Data Exchange (ETDEWEB)

Lopez, Tammy Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-07-17

In the southeastern portion of my home state of New Mexico lies the Chihuahauan desert, where a transuranic (TRU), underground disposal site known as the Waste Isolation Pilot Plant (WIPP) occupies 16 square miles. Full operation status began in March 1999, the year I graduated from Los Alamos High School, in Los Alamos, NM, the birthplace of the atomic bomb and one of the nation’s main TRU waste generator sites. During the time of its development and until recently, I did not have a full grasp on the role Los Alamos was playing in regards to WIPP. WIPP is used to store and dispose of TRU waste that has been generated since the 1940s because of nuclear weapons research and testing operations that have occurred in Los Alamos, NM and at other sites throughout the United States (U.S.). TRU waste consists of items that are contaminated with artificial, man-made radioactive elements that have atomic numbers greater than uranium, or are trans-uranic, on the periodic table of elements and it has longevity characteristics that may be hazardous to human health and the environment. Therefore, WIPP has underground rooms that have been carved out of 2,000 square foot thick salt formations approximately 2,150 feet underground so that the TRU waste can be isolated and disposed of. WIPP has operated safely and successfully until this year, when two unrelated events occurred in February 2014. With these events, the safety precautions and measures that have been operating at WIPP for the last 15 years are being revised and improved to ensure that other such events do not occur again.

2002 WIPP Environmental Monitoring Plan

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2002-09-30

DOE Order 5400.1, General Environmental Protection Program, requires each DOE | facility to prepare an environmental management plan (EMP). This document is | prepared for WIPP in accordance with the guidance contained in DOE Order 5400.1; DOE Order 5400.5, Radiation Protection of the Public and Environment; applicable sections of Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance (DOE/EH-0173T; DOE, 1991); and the Title 10 Code of Federal Regulations (CFR) Part 834, ''Radiation Protection of the Public and Environment'' (draft). Many sections of DOE Order 5400.1 have been replaced by DOE Order 231.1, which is the driver for the annual Site Environmental Report (SER) and the guidance source for preparing many environmental program documents. The WIPP Project is operated by Westinghouse TRU Solutions (WTS) for the DOE. This plan defines the extent and scope of WIPP's effluent and environmental | monitoring programs during the facility's operational life and also discusses WIPP's quality assurance/quality control (QA/QC) program as it relates to environmental monitoring. In addition, this plan provides a comprehensive description of environmental activities at WIPP including: A summary of environmental programs, including the status of environmental monitoring activities A description of the WIPP Project and its mission A description of the local environment, including demographics An overview of the methodology used to assess radiological consequences to the public, including brief discussions of potential exposure pathways, routine and accidental releases, and their consequences Responses to the requirements described in the Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance.

The magnitude and relevance of the February 2014 radiation release from the Waste Isolation Pilot Plant repository in New Mexico, USA

Energy Technology Data Exchange (ETDEWEB)

Thakur, P. [Carlsbad Environmental Monitoring & Research Center, 1400 University Drive, Carlsbad, NM, 88220 (United States); Lemons, B.G.; White, C.R. [AECOM, Carlsbad Operations, Carlsbad, NM, 88220 (United States)

2016-09-15

After almost fifteen years of successful waste disposal operations, the first unambiguous airborne radiation release from the Waste Isolation Pilot Plant (WIPP) was detected beyond the site boundary on February 14, 2014. It was the first accident of its kind in the 15-year operating history of the WIPP. The accident released moderate levels of radioactivity into the underground air. A small but measurable amount of radioactivity also escaped to the surface through the ventilation system and was detected above ground. The dominant radionuclides released were americium and plutonium, in a ratio consistent with the known content of a breached drum. The radiation release was caused by a runaway chemical reaction inside a transuranic (TRU) waste drum which experienced a seal and lid failure, spewing radioactive materials into the repository. According to source-term estimation, approximately 2 to 10 Ci of radioactivity was released from the breached drum into the underground, and an undetermined fraction of that source term became airborne, setting off an alarm and triggering the closure of seals designed to force exhausting air through a system of filters including high-efficiency-particulate-air (HEPA) filters. Air monitoring across the WIPP site intensified following the first reports of radiation detection underground to determine the extent of impact to WIPP personnel, the public, and the environment, if any. This article attempts to compile and interpret analytical data collected by an independent monitoring program conducted by the Carlsbad Environmental Monitoring & Research Center (CEMRC) and by a compliance-monitoring program conducted by the WIPP's management and operating contractor, the Nuclear Waste Partnership (NWP), LLC., in response to the accident. Both the independent and the WIPP monitoring efforts concluded that the levels detected were very low and localized, and no radiation-related health effects among local workers or the public would be

High level nuclear waste repository in salt: Sealing systems status and planning report: Draft report

International Nuclear Information System (INIS)

1985-09-01

This report documents the initial conceptual design studies for a repository sealing system for a high-level nuclear waste repository in salt. The first step in the initial design studies was to review the current design level, termed schematic designs. This review identified practicality of construction and development of a design methodology as two key issues for the conceptual design. These two issues were then investigated during the initial design studies for seal system materials, seal placement, backfill emplacement, and a testing and monitoring plan. The results of these studies have been used to develop a program plan for completion of the sealing system conceptual design. 60 refs., 26 figs., 18 tabs

Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 4, Chapter D, Appendix D1 (beginning), Revision 3

Energy Technology Data Exchange (ETDEWEB)

Lappin, A. R.

1993-03-01

The Waste Isolation Pilot Plant (WIPP), which is designed for receipt, handling, storage, and permanent isolation of defense-generated transuranic wastes, is being excavated at a depth of approximately 655 m in bedded halites of the Permian Salado Formation of southeastern New Mexico. Site-characterization activities at the present WIPP site began in 1976. Full construction of the facility began in 1983, after completion of ``Site and Preliminary Design Validation`` (SPDV) activities and reporting. Site-characterization activities since 1983 have had the objectives of updating or refining the overall conceptual model of the geologic, hydrologic, and structural behavior of the WIPP site and providing data adequate for use in WIPP performance assessment. This report has four main objectives: 1. Summarize the results of WIPP site-characterization studies carried out since the spring of 1983 as a result of specific agreements between the US Department of Energy and the State of New Mexico. 2. Summarize the results and status of site-characterization and facility-characterization studies carried out since 1983, but not specifically included in mandated agreements. 3. Compile the results of WIPP site-characterization studies into an internally consistent conceptual model for the geologic, hydrologic, geochemical, and structural behavior of the WIPP site. This model includes some consideration of the effects of the WIPP facility and shafts on the local characteristics of the Salado and Rustler Formations. 4. Discuss the present limitations and/or uncertainties in the conceptual geologic model of the WIPP site and facility. The objectives of this report are limited in scope, and do not include determination of whether or not the WIPP Project will comply with repository-performance criteria developed by the US Environmental Protection Agency (40CFR191).

Geotechnical instrumentation for repository shafts

International Nuclear Information System (INIS)

Lentell, R.L.; Byrne, J.

1993-01-01

The US Congress passed the Nuclear Waste Policy Act in 1980, which required that three distinctly different geologic media be investigated as potential candidate sites for the permanent disposal of high-level nuclear waste. The three media that were selected for study were basalt (WA), salt (TX, LA, MS, UT), and tuff (NV). Preliminary Exploratory Shaft Facilities (ESF) designs were prepared for seven candidate salt sites, including bedded and domal salt environments. A bedded-salt site was selected in Deaf Smith County, TX for detailed site characterization studies and ESF Final Design. Although Congress terminated the Salt Repository Program in 1988, Final Design for the Deaf Smith ESF was completed, and much of the design rationale can be applied to subsequent deep repository shafts. This paper presents the rationale for the geotechnical instrumentation that was designed for construction and operational performance monitoring of the deep shafts of the in-situ test facility. The instrumentation design described herein can be used as a general framework in designing subsequent instrumentation programs for future high-level nuclear waste repository shafts

Product traceability and quality as applied to the united states transuranic and high-level waste repository programs

International Nuclear Information System (INIS)

Pickering, S.Y.; Orrell, S.A.

2000-01-01

As with any repository program, predictions of the performance of a site over very long time frames may often meet with skepticism from the public and decision-makers, such as regulatory and governmental agencies. Experience at the WIPP and the YMP indicate that demonstrating the defensibility of data, conceptual models, computer codes, and numerical analyses is critical. Five overarching principles have been found to be the basis of a technically and publicly acceptable repository. The principles are traceability, transparency, reproducibility, retrievability, and reviews. - Traceability allows one to understand the source and justification of data and other input that generate conclusions. - Transparency allows one to follow the logic, calculations, and other operations that produce results. - Reproducibility allows one to reconstruct the results without recourse to the originator of the information. - Retrievability allows one to retrieve documentation that demonstrate these overarching principles. - Reviews ensure that the work is technically acceptable, complete, and accurate. This paper discusses how these principles are applied to the WIPP and the YMP. By setting up quality assurance and management controls (e.g., procedures, audits, peer reviews) these principles are implemented. Without successfully applying these principles the WIPP would not have gone from research to industrial maturity. The YMP is ensuring that these are implemented for activities that support licensing. Any repository program concerned with demonstrating defensibility to the public and regulators would do well by incorporating traceability, transparency, reproducibility, retrievability, and reviews into their program. (authors)

New Mexicans debate nuclear waste disposal

International Nuclear Information System (INIS)

Lepkowski, W.

1979-01-01

A brief survey of the background of the Waste Isolation Plant (WIPP) at Carlsbad, New Mexico and the forces at play around WIPP is presented. DOE has plans to establish by 1988 an underground repository for nuclear wastes in the salt formations near Carlsbad. Views of New Mexicans, both pro and con, are reviewed. It is concluded that DOE will have to practice public persuasion to receive approval for the burial of wastes in New Mexico

The integrated in situ testing program for the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Matalucci, R.V.

1987-03-01

The US Department of Energy (DOE) is developing the Waste Isolation Pilot Plant (WIPP) Project in southeastern New Mexico as a research and development (R and D) facility for examining the response of bedded (layered) salt to the emplacement of radioactive wastes generated from defense programs. The WIPP Experimental Program consists of a technology development program, including laboratory testing and theoretical analysis activities, and an in situ testing program that is being done 659 m underground at the project site. This experimental program addresses three major technical areas that concern (1) thermal/structural interactions, (2) plugging and sealing, and (3) waste package performance. To ensure that the technical issues involved in these areas are investigated with appropriate emphasis and timing, an in situ testing plan was developed to integrate the many activities and tasks associated with the technical issues of waste disposal. 5 refs., 4 figs

A comparison of risks due to HLW and SURF repositories in bedded salt

International Nuclear Information System (INIS)

Chu, M.S.Y.; Ortiz, N.R.; Wahi, K.K.

1983-01-01

A methodology was developed to analyze risks from geologic disposal of nuclear wastes. It was applied to estimate the risk due to spent fuel and high-level waste hypothetical repositories in bedded salt. A number of disruptive scenarios were analyzed for each waste type. A comparison between the spent fuel and high-level waste results is presented. The methodology enables one to identify important radionuclides, parameters, and scenarios in terms of their relative contribution to the overall risk or compliance with the proposed EPA Standard

Report on materials characterization center workshop on stress corrosion cracking for the Salt Repository Project, December 16-17, 1986, Seattle, Washington: Workshop summary

International Nuclear Information System (INIS)

Merz, M.D.; Shannon, D.W.

1986-09-01

The Materials Characterization Center (MCC) at Pacific Northwest Laboratory (PNL) conducted a Workshop on Stress Corrosion Cracking for the Salt Repository Project on December 16 and 17, 1986 in Seattle, Washington. The workshop was held to formulate recommendations for addressing stress corrosion cracking (SCC) in a salt repository. It was attended by 24 representatives from major laboratories, universities, and industry. This report presents the recommendations of the workshop, along with the agenda, list of participants, questions and comments, summaries of working groups on low-strength steel and alternate materials, and materials handed out by the speakers

Waste package materials testing for a salt repository: 1983 status summary report

International Nuclear Information System (INIS)

Moak, D.P.

1986-09-01

The United States plans to safely dispose of nuclear waste in deep, stable geologic formations. As part of these plans, the US Department of Energy is sponsoring research on the designing and testing of waste packages and waste package materials. This fiscal year 1983 status report summarizes recent results of waste package materials testing in a salt environment. The results from these tests will be used by waste package designers and performance assessment experts. Release characteristics data are available on two waste forms (spent fuel and waste-containing glass) that were exposed to leaching tests at various radiation levels, temperatures, pH, glass surface area to solution volume ratios, and brine solutions simulating expected salt repository conditions. Candidate materials tested for corrosion resistance and other properties include iron alloys; TI-CODE 12, the most promising titanium alloy for containment; and nickel alloys. In component interaction testing, synergistic effects have not ruled out any candidate material. 21 refs., 37 figs., 15 tabs

New developments in measurement technology relevant to the studies of deep geological repositories in domed salt and basalt

International Nuclear Information System (INIS)

Ramirez, A.L.; Mao, N.H.

1980-01-01

This report briefly describes recent geophysical and geotechnical instrumentation developments relevant to the studies of deep geologic repositories. Special emphasis has been placed on techniques that appear to minimize measurement problems associated with repositories constructed in basalt or domed salt. Included in the listing are existing measurement capabilities and deficiencies that have been identified by a few authors and instrumentation workshops that have assessed the capabilities of existing instrumentation with respect to repository applications. These deficiencies have been compared with the reported advantages and limitations of the new developments described. Based on these comparisons, areas that merit further research and development have been identified. The report is based on a thorough literature review and on discussions with several instrumentation specialists involved in instrumentation development

Generic aspects of salt repositories

International Nuclear Information System (INIS)

Laughon, R.B.

1979-01-01

The history of geological disposal of radioactive wastes in salt is presented from 1957 when a panel of the National Academy of Sciences-National Research Council recommended burial in bedded salt deposits. Early work began in the Kansas, portion of the Permian Basin where simulated wastes were placed in an abandoned salt mine at Lyons, Kansas, in the late 1960's. This project was terminated when the potential effect of nearby solution mining activities could not be resolved. Evaluation of bedded salts resumed a few years later in the Permian Basin in southeastern New Mexico, and search for suitable sites in the 1970's resulted in the formation of the National Waste Terminal Storage Program in 1976. Evaluation of salt deposits in many regions of the United States has been virtually completed and has shown that deposits having the greatest potential for radioactive waste disposal are those of the largest depositional basins and salt domes of the Gulf Coast region

Preliminary petrological and geochemical results from the Salton Sea Geothermal Field, California: A near-field natural analog of a radioactive waste repository in salt: Topical report No. 2

International Nuclear Information System (INIS)

Elders, W.A.; Cohen, L.H.; Williams, A.E.; Neville, S.; Collier, P.; Oakes, C.

1986-03-01

High concentrations of radionuclides and high temperatures are not naturally encountered in salt beds. For this reason, the Salton Sea Geothermal Field (SSGF) may be the best available geologic analog of some of the processes expected to occur in high level nuclear waste repositories in salt. Subsurface temperatures and brine concentrations in the SSGF span most of the temperature range and fluid inclusion brine range expected in a salt repository, and the clay-rich sedimentary rocks are similar to those which host bedded or domal salts. As many of the chemical processes observed in the SSGF are similar to those expected to occur in or near a salt repository, data derived from it can be used in the validation of geochemical models of the near-field of a repository in salt. This report describes preliminary data on petrology and geochemistry, emphasizing the distribution of rare earth elements and U and Th, of cores and cuttings from several deep wells chosen to span a range of temperature gradients and salinities. Subsurface temperature logs have been augmented by fluid inclusion studies, to reveal the effects of brines of varying temperature and salinity. The presence of brines with different oxygen isotopic signatures also indicate lack of mixing. Whole rock major, minor and trace element analyses and data on brine compositions are being used to study chemical migration in these sediments. 65 refs., 20 figs., 3 tabs

Efficacy of backfilling and other engineered barriers in a radioactive waste repository in salt

International Nuclear Information System (INIS)

Claiborne, H.C.

1982-09-01

In the United States, investigation of potential host geologic formations was expanded in 1975 to include hard rocks. Potential groundwater intrusion is leading to very conservative and expensive waste package designs. Recent studies have concluded that incentives for engineered barriers and 1000-year canisters probably do not exist for reasonable breach scenarios. The assumption that multibarriers will significantly increase the safety margin is also questioned. Use of a bentonite backfill for surrounding a canister of exotic materials was developed in Sweden and is being considered in the US. The expectation that bentonite will remain essentially unchanged for hundreds of years for US repository designs may be unrealistic. In addition, thick bentonite backfills will increase the canister surface temperature and add much more water around the canister. The use of desiccant materials, such as CaO or MgO, for backfilling seems to be a better method of protecting the canister. An argument can also be made for not using backfill material in salt repositories since the 30-cm-thick space will provide for hole closure for many years and will promote heat transfer via natural convection. It is concluded that expensive safety systems are being considered for repository designs that do not necessarily increase the safety margin. It is recommended that the safety systems for waste repositories in different geologic media be addressed individually and that cost-benefit analyses be performed

Will America's nuclear waste be laid to rest

Energy Technology Data Exchange (ETDEWEB)

Charles, D

1991-12-14

The Waste Isolation Pilot Plant (WIPP) in New Mexico, was designed to store waste from the United States (U.S.) nuclear weapons production in deep repositories under the naturally occurring salt beds. However no waste can be put into the repository until safety checks, designed as nuclear reactor safety standards, have been satisfactorily completed to the U.S. congress's satisfaction. While political controversy reigns the WIPP structure stands empty and steel drums of radioactive waste remain at the U.S. nuclear weapons factories. Proponents say costly capital investment is being wasted, opponents that people and the environment would be at risk of contamination if safety standards were not understood and adhered to. (UK).

Achieving WIPP certification for software. A white paper

International Nuclear Information System (INIS)

Matthews, S.D.; Adams, K.; Twitchell, K.E.

1998-07-01

The NMT-1 and NMT-3 organizations within the Chemical and Metallurgical Research (CMR) facility at the Los Alamos National Laboratory (LANL) is working to achieve Waste Isolation Pilot Plant (WIPP) certification to enable them to transport their TRU waste to WIPP. In particular, the NMT-1 management is requesting support from the Idaho National Engineering and Environmental Laboratory (INEEL) to assist them in making the Laboratory Information Management System (LIMS) software WIPP certifiable. Thus, LIMS must be compliant with the recognized software quality assurance (SQA) requirements stated within the QAPD. Since the Idaho National Engineering and Environmental Laboratory (INEEL) has achieved WIPP certification, INEEL personnel can provide valuable assistance to LANL by sharing lessons learned and recommendations. Thus, this white paper delineates the particular software quality assurance requirements required for WIPP certification

The WIPP Water Quality Sampling Program

International Nuclear Information System (INIS)

Uhland, D.; Morse, J.G.; Colton, D.

1986-01-01

The Waste Isolation Pilot Plant (WIPP), a Department of Energy facility, will be used for the underground disposal of wastes. The Water Quality Sampling Program (WQSP) is designed to obtain representative and reproducible water samples to depict accurate water composition data for characterization and monitoring programs in the vicinity of the WIPP. The WQSP is designed to input data into four major programs for the WIPP project: Geochemical Site Characterization, Radiological Baseline, Environmental Baseline, and Performance Assessment. The water-bearing units of interest are the Culebra and Magneta Dolomite Members of the Rustler Formation, units in the Dewey Lake Redbeds, and the Bell Canyon Formation. At least two chemically distinct types of water occur in the Culebra, one being a sodium/potassium chloride water and the other being a calcium/magnesium sulfate water. Water from the Culebra wells to the south of the WIPP site is distinctly fresher and tends to be of the calcium/magnesium sulfate type. Water in the Culebra in the north and around the WIPP site is distinctly fresher and tends to be of the sodium/potassium chloride type and is much higher in total dissolved solids. The program, which is currently 1 year old, will continue throughout the life of the facility as part of the Environmental Monitoring Program

WIPP fire hazards and risk analysis

International Nuclear Information System (INIS)

1991-05-01

The purpose of this analysis was to conduct a fire hazards risk analysis of the Transuranic (TRU) contact-handled waste receipt, emplacement, and disposal activities at the Waste Isolation Pilot Plant (WIPP). The technical bases and safety envelope for these operations are defined in the approved WIPP Final Safety Analysis Report (FSAR). Although the safety documentation for the initial phase of the Test Program, the dry bin scale tests, has not yet been approved by the Department of Energy (DOE), reviews of the draft to date, including those by the Advisory Committee on Nuclear Facility Safety (ACNFS), have concluded that the dry bin scale tests present no significant risks in excess of those estimated in the approved WIPP FSAR. It is the opinion of the authors and reviewers of this analysis, based on sound engineering judgment and knowledge of the WIPP operations, that a Fire Hazards and Risk Analysis specific to the dry bin scale test program is not warranted prior to first waste receipt. This conclusion is further supported by the risk analysis presented in this document which demonstrates the level of risk to WIPP operations posed by fire to be extremely low. 15 refs., 41 figs., 48 tabs

Schematic designs for penetration seals for a repository in the Paradox Basin

International Nuclear Information System (INIS)

Kelsall, P.C.; Meyer, D.; Case, J.B.; Coons, W.E.

1985-12-01

The isolation of radioactive wastes in geologic repositories requires that human-made penetrations such as shafts, tunnels, or boreholes are adequately sealed. This report describes schematic seal designs for a repository in bedded salt referenced to the stratigraphy of the Paradox Basin. The designs are presented for extensive peer review and will be updated as conceptual designs if the Paraodx Basin is selected as a candidate repository site. The principal components used in the shaft seal system are concrete bulkheads interspersed with highly compacted bentonite-rich earth fill. In the repository-level tunnels and rooms, the principal material used in the seal system is crushed salt obtained from excavating the repository. It is anticipated that crushed salt will consolidate in response to closure of the repository rooms, to the degree that mechanical and hydrologic properties will eventually match those of undisturbed, intact salt. For Paradox Basin Cycle 6 salt, analyses indictate that this process will require approximately 300 years for a seal located at the base of one of the repository shafts (where there is little increase in temperature due to waste emplacement) and approximately 140 years for a seal located in a main passageway within the repository. These analyses are based on uncertain laboratory data regarding intact salt creep rates and crushed salt consolidation characteristics, and must be regarded as preliminary

Salt Repository Project: Waste Package Program (WPP) modeling activiteis: FY 1984 annual report

International Nuclear Information System (INIS)

Kuhn, W.L.; Simonson, S.A.; Pulsipher, B.A.

1987-03-01

The Pacific Northwest Laboratory (PNL) is supporting the US Department of Energy's (DOE) Salt Repository Project (SRP) through its Waste Package Program (WPP). During FY 1984, the WPP continued its program of waste package component development and interactions testing and application of the resulting data base to develop predictive models describing waste package degradation and radionuclide release. Within the WPP, the Modeling Task (Task 04 during FY 1984) was conducted to interpret the tests in such a way that scientifically defensible models can be developed for use in qualification of the waste package

Salt disposal: Paradox Basin, Utah

International Nuclear Information System (INIS)

1983-04-01

This report presents the findings of a study conducted for the National Waste Terminal Storage (NWTS) Program. Permanent disposal options are examined for salt resulting from the excavation of a waste repository in the bedded salt deposits of the Paradox Basin of southeastern Utah. The study is based on a repository salt backfill compaction of 60% of the original density which leaves a total of 8 million tons of 95% pure salt to be disposed of over a 30-year period. The feasibility, impacts, and mitigation methods are examined for five options: commercial disposal, permanent onsite surface disposal, permanent offsite disposal, deepwell injection, and ocean and Great Salt Lake disposal. The study concludes the following: Commercial marketing of all repository salt would require a subsidy for transportation to major salt markets. Permanent onsite surface storage is both economically and technically feasible. Permanent offsite disposal is technically feasible but would incur additional transportation costs. Selection of an offsite location would provide a means of mitigating impacts associated with surface storage at the repository site. Deepwell injection is an attractive disposal method; however, the large water requirement, high cost of development, and poor performance of similar operating brine disposal wells eliminates this option from consideration as the primary means of disposal for the Paradox Basin. Ocean disposal is expensive because of high transportation cost. Also, regulatory approval is unlikely. Ocean disposal should be eliminated from further consideration in the Paradox Basin. Great Salt Lake disposal appears to be technically feasible. Great Salt Lake disposal would require state approval and would incur substantial costs for salt transportation. Permanent onsite disposal is the least expensive method for disposal of all repository salt

Evaluation of the WIPP Project`s compliance with the EPA radiation protection standards for disposal of transuranic waste

Energy Technology Data Exchange (ETDEWEB)

Neill, R.H.; Chaturvedi, L.; Rucker, D.F.; Silva, M.K.; Walker, B.A.; Channell, J.K.; Clemo, T.M. [Environmental Evaluation Group, Albuquerque, NM (United States)]|[Environmental Evaluation Group, Carlsbad, NM (United States)

1998-03-01

The US Environmental Protection Agency`s (EPA) proposed rule to certify that the Waste Isolation Pilot Plant (WIPP) meets compliance with the long-term radiation protection standards for geologic repositories (40CFR191 Subparts B and C), is one of the most significant milestones to date for the WIPP project in particular, and for the nuclear waste issue in general. The Environmental Evaluation Group (EEG) has provided an independent technical oversight for the WIPP project since 1978, and is responsible for many improvements in the location, design, and testing of various aspects of the project, including participation in the development of the EPA standards since the early 1980s. The EEG reviewed the development of documentation for assessing the WIPP`s compliance by the Sandia National Laboratories following the 1985 promulgation by EPA, and provided many written and verbal comments on various aspects of this effort, culminating in the overall review of the 1992 performance assessment. For the US Department of Energy`s (DOE) compliance certification application (CCA), the EEG provided detailed comments on the draft CCA in March, 1996, and additional comments through unpublished letters in 1997 (included as Appendices 8.1 and 8.2 in this report). Since the October 30, 1997, publication of the EPA`s proposed rule to certify WIPP, the EEG gave presentations on important issues to the EPA on December 10, 1997, and sent a December 31, 1997 letter with attachments to clarify those issues (Appendix 8.3). The EEG has raised a number of questions that may have an impact on compliance. In spite of the best efforts by the EEG, the EPA reaction to reviews and suggestions has been slow and apparently driven by legal considerations. This report discusses in detail the questions that have been raised about containment requirements. Also discussed are assurance requirements, groundwater protection, individual protection, and an evaluation of EPA`s responses to EEG`s comments.

Thermoelastic analyses of spent fuel repositories in bedded and dome salt. Technical memorandum report RSI-0054

International Nuclear Information System (INIS)

Callahan, G.D.; Ratigan, J.L.

1978-01-01

Global thermoelastic analyses of bedded and dome salt models showed a slight preference for the bedded salt model through the range of thermal loading conditions. Spent fuel thermal loadings should be less than 75 kW/acre of the repository pending more accurate material modeling. One should first limit the study to one or two spent fuel thermal loading (i.e. 75 kW/acre and/or 50 kW/acre) analyses up to a maximum time of approximately 2000 years. Parametric thermoelastic type analyses could then be readily obtained to determine the influence of the thermomechanical properties. Recommendations for further study include parametric analyses, plasticity analyses, consideration of the material interfaces as joints, and possibly consideration of a global joint pattern (i.e. jointed at the same orientation everywhere) for the non-salt materials. Subsequently, the viscoelastic analyses could be performed

Analysis of corrosion data for carbon steels in simulated salt repository brines and acid chloride solutions at high temperatures

International Nuclear Information System (INIS)

Diercks, D.R.; Hull, A.B.; Kassner, T.F.

1988-03-01

Carbon steel is currently the leading candidate material for fabrication of a container for isolation of high level nuclear waste in a salt repository. Since brine entrapped in the bedded salt can migrate to the container by several transport processes, corrosion is an important consideration in the long-term performance of the waste package. A detailed literature search was performed to compile relevant corrosion data for carbon steels in anoxic acid chloride solutions, and simulated salt repository brines at temperatures between ∼ 20 and 400 0 C. The hydrolysis of Mg 2+ ions in simulated repository brines containing high magnesium concentrations causes acidification at temperatures above 25 0 C, which, in turn, influences the protective nature of the magnetite corrosion product layer on carbon steel. The corrosion data for the steels were analyzed, and an analytical model for general corrosion was developed to calculate the amount of penetration (i.e., wall thinning) as a function of time, temperature, and the pressure of corrosion product hydrogen than can build up during exposure in a closed system (e.g., a sealed capsule). Both the temperature and pressure dependence of the corrosion rate of steels in anoxic acid chloride solutions indicate that the rate-controlling partial reaction is the cathodic reduction of water to form hydrogen. Variations in the composition and microstructure of the steels or the concentration of the ionic species in the chloride solutions (provided that they do not change the pH significantly) do not appear to strongly influence the corrosion rate

Salt Repository Project site study plan for background environmental radioactivity: Revision 1

International Nuclear Information System (INIS)

1987-12-01

The Site Study Plan for Background Environmental Radioactivity describes a field program consisting of an initial radiological survey and a radiological sampling program. The field program includes measurement of direct radiation and collection and analysis of background radioactivity samples of air, precipitation, soil, water, milk, pasture grass, food crops, meat, poultry, game, and eggs. The plan describes for each study the need for the study, the study design, data management, and use, schedule of proposed activities, and quality assurance requirements. These studies will provide data needed to satisfy requirements contained in, or derived from, the Salt Repository Project Requirements Document. 43 refs., 10 figs., 7 tabs

Waste Isolation Pilot Plant: Draft Supplement Environmental Impact Statement

International Nuclear Information System (INIS)

1989-04-01

The US Department of Energy (DOE) has prepared this supplement to the 1980 Final Environmental Impact Statement (FEIS) for the Waste Isolation Pilot Plant (WIPP) in order to assess the environmental impacts that may occur from the continued development of the WIPP as a minced geologic repository for transuranic (TRU) waste. Since the publication of the FEIS in October 1980, new data collected at the WIPP have led to changes in the understanding of the hydrogeologic characteristics of the area and their potential implications for the long-term performance of the WIPP. In addition, there have been changes in the FEIS Proposed Action and new regulatory requirements. This supplement to the FEIS (SEIS) evaluates the environmental consequences of the Proposed Action as modified since 1980 in light of new data and assumptions. The new information pertains mainly to the geologic and hydrologic systems at the WIPP site and their effect on the long-term performance of the WIPP. The SEIS includes new data indicating that: the permeability of the Salado Formation, the geologic formation in which the WIPP underground facilities are located, is lower than previously believed; the moisture content of the Salado Formation and the consequent brine inflow is higher than previously believed; a higher transmissivity zone is present in the Rustler Formation in the southeastern portion of the WIPP site; and ''salt creep'' (convergence) in the repository occurs faster than previously believed. Volume 2 contains 11 appendices

Accumulated energy determination in salts rocks irradiated by means of thermoluminescence techniques: application to the high level radioactive wastes repositories analysis

International Nuclear Information System (INIS)

Dies, J.; Ortega. J.; Tarrasa. F.; Cuevas, C.

1995-01-01

The report summarizes the study carried out to develop the radiation effects on salt rocks in order to repository the high level radioactive wastes. The study is structured into 3 main aspects: 1.- Analysis of irradiation experiences in Haw project of Pet ten reactor. 2.- Irradiation of salt sample of CESAR industrial irradiator. 3.- Correlation study between the accumulated energy, termoluminescence answer and the defect concentration

Analyses of SRS waste glass buried in granite in Sweden and salt in the United States

International Nuclear Information System (INIS)

Williams, J.P.; Wicks, G.G.; Clark, D.E.; Lodding, A.R.

1991-01-01

Simulated Savannah River Site (SRS) waste glass forms have been buried in the granite geology of the Stirpa mine in Sweden for two years. Analyses of glass surfaces provided a measure of the performance of the waste glasses as a function of time. Similar SRS waste glass compositions have also been buried in salt at the WIPP facility in Carlsbad, New Mexico for a similar time period. Analyses of the SRS waste glasses buried in-situ in granite will be presented and compared to the performance of these same compositions buried in salt at WIPP

WIPP 2004 Site Environmental Report

Energy Technology Data Exchange (ETDEWEB)

None, None

2005-09-30

The mission of Waste Isolation Pilot Plant (WIPP) is to safely and permanently dispose of transuranic (TRU) radioactive waste generated by the production of nuclear weapons and other activities related to the national defense of the United States (U.S.). In 2004, 8,839 cubic meters (m3) of TRU waste were emplaced at WIPP. From the first receipt of waste in March 1999 through the end of 2004, 25,809 m3 of TRU waste had been emplaced at WIPP. The U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) and Washington TRU Solutions LLC (WTS) are dedicated to maintaining high quality management of WIPP environmental resources. DOE Order 450.1, Environmental Protection Program; DOE Order 231.1A, Environment, Safety, and Health Reporting; and DOE Order 5400.5, Radiation Protection of the Public and Environment, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 2004 Site Environmental Report (SER) summarizes environmental data from 2004 that characterize environmental management performance and demonstrate compliance with applicable federal and state regulations. This report was prepared in accordance with DOE Order 231.1A, and Guidance for the Preparation of DOE Annual Site Environmental Reports (ASERs) for Calendar Year 2004 (DOE, 2005). The order and the guidance require that DOE facilities submit an annual SER to the DOE Headquarters Office of the Assistant Secretary for Environment, Safety, and Health. The WIPP Hazardous Waste Facility Permit (HWFP) further requires that the SER be provided to the New Mexico Environment Department (NMED).

WIPP 2004 Site Environmental Report

International Nuclear Information System (INIS)

2005-01-01

The mission of Waste Isolation Pilot Plant (WIPP) is to safely and permanently dispose of transuranic (TRU) radioactive waste generated by the production of nuclear weapons and other activities related to the national defense of the United States (U.S.). In 2004, 8,839 cubic meters (m3) of TRU waste were emplaced at WIPP. From the first receipt of waste in March 1999 through the end of 2004, 25,809 m3 of TRU waste had been emplaced at WIPP. The U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) and Washington TRU Solutions LLC (WTS) are dedicated to maintaining high quality management of WIPP environmental resources. DOE Order 450.1, Environmental Protection Program; DOE Order 231.1A, Environment, Safety, and Health Reporting; and DOE Order 5400.5, Radiation Protection of the Public and Environment, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 2004 Site Environmental Report (SER) summarizes environmental data from 2004 that characterize environmental management performance and demonstrate compliance with applicable federal and state regulations. This report was prepared in accordance with DOE Order 231.1A, and Guidance for the Preparation of DOE Annual Site Environmental Reports (ASERs) for Calendar Year 2004 (DOE, 2005). The order and the guidance require that DOE facilities submit an annual SER to the DOE Headquarters Office of the Assistant Secretary for Environment, Safety, and Health. The WIPP Hazardous Waste Facility Permit (HWFP) further requires that the SER be provided to the New Mexico Environment Department (NMED).

Mined salt storage feasibility: Engineering study report

International Nuclear Information System (INIS)

1987-07-01

This study addresses a method of eliminating the surface storage of mined salt at the Deaf Smith repository site. It provides rough estimates of the logistics and costs of transporting 3.7 million tons of salt from the repository to the salt disposal site near Carlsbad, New Mexico and returning it to the repository for decommissioning backfill. The study assumes that a railcar/truck system will be installed and that the excavated salt will be transported from the repository to an existing potash mine located near Carlsbad, New Mexico approximately 300 miles from the repository. The 3.7 million tons of salt required for repository decommissioning backfill can be stored in the potash mines along with the excess salt, with no additional capital costs required for either a railcar or a truck transportation system. The capital cost for facilities to reclaim the 3.7 million tons of salt from the potash mine is estimated to be $4,400,000 with either a rail or truck transportation system. Segregating the 3.7 million tons of backfill salt in a surface storage area at the potash mine requires a capital cost of $13,900,000 with a rail system or $11,400,000 with a truck system. Transportation costs are estimated at $0.08/ton-mile for rail and $0.13/ton-mile for truck. 2 figs., 5 tabs

Reconsolidated Salt as a Geotechnical Barrier

International Nuclear Information System (INIS)

Hansen, Francis D.; Gadbury, Casey

2015-01-01

Salt as a geologic medium has several attributes favorable to long-term isolation of waste placed in mined openings. Salt formations are largely impermeable and induced fractures heal as stress returns to equilibrium. Permanent isolation also depends upon the ability to construct geotechnical barriers that achieve nearly the same high-performance characteristics attributed to the native salt formation. Salt repository seal concepts often include elements of reconstituted granular salt. As a specific case in point, the Waste Isolation Pilot Plant recently received regulatory approval to change the disposal panel closure design from an engineered barrier constructed of a salt-based concrete to one that employs simple run-of-mine salt and temporary bulkheads for isolation from ventilation. The Waste Isolation Pilot Plant is a radioactive waste disposal repository for defense-related transuranic elements mined from the Permian evaporite salt beds in southeast New Mexico. Its approved shaft seal design incorporates barrier components comprising salt-based concrete, bentonite, and substantial depths of crushed salt compacted to enhance reconsolidation. This paper will focus on crushed salt behavior when applied as drift closures to isolate disposal rooms during operations. Scientific aspects of salt reconsolidation have been studied extensively. The technical basis for geotechnical barrier performance has been strengthened by recent experimental findings and analogue comparisons. The panel closure change was accompanied by recognition that granular salt will return to a physical state similar to the halite surrounding it. Use of run-of-mine salt ensures physical and chemical compatibility with the repository environment and simplifies ongoing disposal operations. Our current knowledge and expected outcome of research can be assimilated with lessons learned to put forward designs and operational concepts for the next generation of salt repositories. Mined salt

Reconsolidated Salt as a Geotechnical Barrier

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gadbury, Casey [USDOE Carlsbad Field Office, NM (United States)

2015-11-01

Salt as a geologic medium has several attributes favorable to long-term isolation of waste placed in mined openings. Salt formations are largely impermeable and induced fractures heal as stress returns to equilibrium. Permanent isolation also depends upon the ability to construct geotechnical barriers that achieve nearly the same high-performance characteristics attributed to the native salt formation. Salt repository seal concepts often include elements of reconstituted granular salt. As a specific case in point, the Waste Isolation Pilot Plant recently received regulatory approval to change the disposal panel closure design from an engineered barrier constructed of a salt-based concrete to one that employs simple run-of-mine salt and temporary bulkheads for isolation from ventilation. The Waste Isolation Pilot Plant is a radioactive waste disposal repository for defense-related transuranic elements mined from the Permian evaporite salt beds in southeast New Mexico. Its approved shaft seal design incorporates barrier components comprising salt-based concrete, bentonite, and substantial depths of crushed salt compacted to enhance reconsolidation. This paper will focus on crushed salt behavior when applied as drift closures to isolate disposal rooms during operations. Scientific aspects of salt reconsolidation have been studied extensively. The technical basis for geotechnical barrier performance has been strengthened by recent experimental findings and analogue comparisons. The panel closure change was accompanied by recognition that granular salt will return to a physical state similar to the halite surrounding it. Use of run-of-mine salt ensures physical and chemical compatibility with the repository environment and simplifies ongoing disposal operations. Our current knowledge and expected outcome of research can be assimilated with lessons learned to put forward designs and operational concepts for the next generation of salt repositories. Mined salt

US waste management overview, new legislation, and status and plans of the disposal program

International Nuclear Information System (INIS)

Isaacs, T.

1988-01-01

The Nuclear Waste Policy Act of 1982 provided a comprehensive master plan for the United States to locate a nuclear waste repository. Details of this process, which began with 9 sites, are well known. One repository was to be provided with a 70,000 metric ton limit on capacity. Provisions were to be made for transportation and a proposed MRS facility, and for activities leading to the potential siting of a second repository. A decision analysis technique was used by DOE in nominating three repository sites for characterization. The second repository program, which had become a matter of political controversy, was stopped because the first repository would have enough capacity for all commercial spent fuel for some time to come. A court decision to drop the MRS was later overruled. DOE still wants a vigorous international program along with work concerned with any rock medium that can be of potential value to the US repository effort. WIPP will continue to be of interest and emphasis as a repository project in salt for defense transuranic wastes. High-level wastes will not be permanently isolated at WIPP

Salt repository project site study plan for water resources: Revision 1

International Nuclear Information System (INIS)

1987-12-01

The Site Study Plan for Water Resources describes a field program consisting of surface-water and ground-water characterization. The surface-water studies will determine the drainage basin characteristics (i.e., topography, soils, land use), hydrometeorology, runoff to streams and playas, and surface-water quality (i.e., offsite pollution sources in playa lakes and in streams). The environmental ground-water studies will focus on ground-water quality characterization. The site study plan describes for each study the need for the study, study design, data management and use, schedule of proposed activities, and quality assurance. These studies will provide data needed to satisfy requirements contained in, or derived from, the Salt Repository Projects Requirements Document. 78 refs., 8 figs., 5 tabs

Representation of spatial variability for modelling of flow and transport processes in the Culebra Dolomite at the WIPP site

International Nuclear Information System (INIS)

Meigs, L.C.; Beauheim, R.L.

1997-01-01

The Waste Isolation Pilot Plant (WIPP) is a proposed repository for transuranic wastes constructed in bedded Permian-acre halite deposits in southeastern New Mexico, USA. Site-characterization studies at the WIPP site identified groundwater flow in the Culebra Dolomite Member of the Rustler Formation as the most likely Geologic pathway for radio nuclide transport to the accessible environment in the event of a breach of the WIPP repository through inadvertent human intrusion. The Culebra is a 7-m-thick, variably fractured dolomite with massive and layers. Detailed studies at all scales demonstrated that the Culebra is a heterogeneous medium. Heterogeneity in Culebra properties was incorporated into numerical simulations used for data interpretation and PA calculations in different ways, depending on the amount of data available, the certainty with which the effects of a given approach could be evaluated, and the purpose of the study. When abundant, spatially distributed data were available, the heterogeneity was explicitly included. For example, a stochastic approach was used to generate numerous, equally likely, heterogeneous transmissivity fields conditioned on head and transmissivity data. In other cases, constant parameter values were applied over the model domain. These constant values were selected and applied in two different ways. In simple cases where a conservative bounding value could be identified that would not lead to unrealistically conservative results, that value was used for all calculations. In more complex cases, parameter distributions were developed and single values of the parameters were sampled from the distributions and applied across the entire model domain for each of the PA Monte Carlo simulations. We are currently working to refine our understanding of the multiple rates of diffusion attributable to small-scale spatial variability

Salton Sea geothermal field as a natural analog for the near-field in a salt high-level nuclear waste repository

International Nuclear Information System (INIS)

Elders, W.A.; Moody, J.B.; Battelle Memorial Inst., Columbus, OH)

1984-01-01

The Salton Sea Geothermal Field (SSGF), on the delta of the Colorado River in southern California, is being studied as a natural analog for the near-field environment of proposed nuclear waste repositories in salt. A combination of mineralogical and geochemical methods is being employed to develop a three-dimenisonal picture of temperature, salinity, lithology, mineralogy, and chemistry of reactions between the reservoir rocks and the hot brines. Our aim is to obtain quantitative data on mineral stabilities and on mobilities of the naturally occurring radionuclides of concern in Commercial High-Level Waste (CHLW). These data will be used to validate the EQ3/6 geochemical code under development to model the salt near-field repository behavior. Maximum temperatures encountered in wells in the SSGF equal or exceed peak temperatures expected in a salt repository. Brines produced from these wells have major element chemistry similar to brines from candidate salt sites. Relative to the rocks, these brines are enriched in Na, Mn, Sr, Ra, and Po, depleted in Ba, Si, Mg, Ti, and Al, and strongly depleted in U and Th. However, the unaltered rocks contain only about 2 to 3 ppm of U and 4 to 12 ppm of Th, largely in detrital epidotes and zircons. Samples of hydrothermally altered rocks from a wide range of temperature and salinity show rather similar uniform low concentrations of these elements, even when authigenic illite, chlorite, ipidote and feldspar are present. These observations suggest that U and Th are relatively immobile in these hot brines. However, Ra, Po, Cs, and Sr are relatively mobile. Work is continuing to document naturally occurring radionuclide partitioning between SSGF minears and brine over a range of temperature, salinity, and lithology. 8 refs., 7 figs., 2 tabs

Resource Conservation and Recovery Act, Part B Permit Application

International Nuclear Information System (INIS)

1993-01-01

The Waste Isolation Pilot Plant (WIPP) Project was authorized by the US Department of Energy 5 (DOE) National Security and Military Applications of the Nuclear Energy Authorization Act of 1980 (Public Law 96-164). Its legislative mandate is to provide a research and development facility to demonstrate the safe disposal of radioactive waste resulting from national defense programs and activities. To fulfill this mandate, the WIPP facility has been designed to perform scientific investigations of the behavior of bedded salt as a repository medium and the interactions between the soft and radioactive wastes. In 1991, DOE proposed to initiate a experimental Test Phase designed to demonstrate the performance of the repository. The Test Phase activities involve experiments using transuranic (TRU) waste typical of the waste planned for future disposal at the WIPP facility. Much of this TRU waste is co-contaminated with chemical constituents which are defined as hazardous under HWMR-7, Pt. II, sec. 261. This waste is TRU mixed waste and is the subject of this application. Because geologic repositories, such as the WIPP facility, are defined under the Resource Conservation and Recovery Act (RCRA) as land disposal facilities, the groundwater monitoring requirements of HWMR-7, PLV, Subpart X, must be addressed. HWMR-7, Pt. V, Subpart X, must be addressed. This appendix demonstrates that groundwater monitoring is not needed in order to demonstrate compliance with the performance standards; therefore, HWMR-7, Pt.V, Subpart F, will not apply to the WIPP facility

Repository environmental parameters and models/methodologies relevant to assessing the performance of high-level waste packages in basalt, tuff, and salt

Energy Technology Data Exchange (ETDEWEB)

Claiborne, H.C.; Croff, A.G.; Griess, J.C.; Smith, F.J.

1987-09-01

This document provides specifications for models/methodologies that could be employed in determining postclosure repository environmental parameters relevant to the performance of high-level waste packages for the Basalt Waste Isolation Project (BWIP) at Richland, Washington, the tuff at Yucca Mountain by the Nevada Test Site, and the bedded salt in Deaf Smith County, Texas. Guidance is provided on the identify of the relevant repository environmental parameters; the models/methodologies employed to determine the parameters, and the input data base for the models/methodologies. Supporting studies included are an analysis of potential waste package failure modes leading to identification of the relevant repository environmental parameters, an evaluation of the credible range of the repository environmental parameters, and a summary of the review of existing models/methodologies currently employed in determining repository environmental parameters relevant to waste package performance. 327 refs., 26 figs., 19 tabs.

Repository environmental parameters and models/methodologies relevant to assessing the performance of high-level waste packages in basalt, tuff, and salt

International Nuclear Information System (INIS)

Claiborne, H.C.; Croff, A.G.; Griess, J.C.; Smith, F.J.

1987-09-01

This document provides specifications for models/methodologies that could be employed in determining postclosure repository environmental parameters relevant to the performance of high-level waste packages for the Basalt Waste Isolation Project (BWIP) at Richland, Washington, the tuff at Yucca Mountain by the Nevada Test Site, and the bedded salt in Deaf Smith County, Texas. Guidance is provided on the identify of the relevant repository environmental parameters; the models/methodologies employed to determine the parameters, and the input data base for the models/methodologies. Supporting studies included are an analysis of potential waste package failure modes leading to identification of the relevant repository environmental parameters, an evaluation of the credible range of the repository environmental parameters, and a summary of the review of existing models/methodologies currently employed in determining repository environmental parameters relevant to waste package performance. 327 refs., 26 figs., 19 tabs

Backfilling and sealing of repositories and access shafts and galleries in clay, granite and salt formations

International Nuclear Information System (INIS)

Lake, L.M.; Davies, I.L.; Gera, F.; Jorda, M.; McEwen, T.; Neerdael, B.; Schmidt, M.W.

1985-01-01

The paper summarizes the work carried out under ten Commission contracts in the field of backfilling and sealing radioactive waste repositories. It covers theoretical, laboratory and field trials and experiments involving three potential host types, namely clay, salt and hard rock. It concludes that maximum opportunity should be taken over the next 15 to 25 years with a view to obtaining first hand experience in real ground with real wastes

Environmental and health impacts of February 14, 2014 radiation release from the nation's only deep geologic nuclear waste repository.

Science.gov (United States)

Thakur, P; Lemons, B G; Ballard, S; Hardy, R

2015-08-01

The environmental impact of the February 14, 2014 radiation release from the nation's only deep geologic nuclear waste repository, the Waste Isolation Pilot Plant (WIPP) was assessed using monitoring data from an independent monitoring program conducted by the Carlsbad Environmental Monitoring & Research Center (CEMRC). After almost 15 years of safe and efficient operations, the WIPP had one of its waste drums rupture underground resulting in the release of moderate levels of radioactivity into the underground air. A small amount of radioactivity also escaped to the surface through the ventilation system and was detected above ground. It was the first unambiguous release from the WIPP repository. The dominant radionuclides released were americium and plutonium, in a ratio that matches the content of the breached drum. The accelerated air monitoring campaign, which began following the accident, indicates that releases were low and localized, and no radiation-related health effects among local workers or the public would be expected. The highest activity detected was 115.2 μBq/m(3) for (241)Am and 10.2 μBq/m(3) for (239+240)Pu at a sampling station located 91 m away from the underground air exhaust point and 81.4 μBq/m(3) of (241)Am and 5.8 μBq/m(3) of (239+240)Pu at a monitoring station located approximately one kilometer northwest of the WIPP facility. CEMRC's recent monitoring data show that the concentration levels of these radionuclides have returned to normal background levels and in many instances, are not even detectable, demonstrating no long-term environmental impacts of the recent radiation release event at the WIPP. This article presents an evaluation of almost one year of environmental monitoring data that informed the public that the levels of radiation that got out to the environment were very low and did not, and will not harm anyone or have any long-term environmental consequence. In terms of radiological risk at or in the vicinity of the

Numerical and experimental investigations on the time dependent behavior of a salt dome with a high-level waste repository

International Nuclear Information System (INIS)

Prij, J.; Vons, L.H.

1984-01-01

Results are presented of in-situ measurements, performed in a 300 m deep dry-drilled borehole, in the ASSE-mine. Convergence measurements at ambient as well as elevated temperatures and pressure measurements at elevated temperatures are discussed. Creep equations derived from these experiments are used for the numerical analysis of the time dependent behavior of a salt dome with a HLW repository. The analyses show that the total stresses in the salt remain compressive with deviatoric components smaller than 3 MPa. 9 references, 6 figures, 1 table

Brine Sampling and Evaluation Program

International Nuclear Information System (INIS)

Deal, D.E.; Case, J.B.; Deshler, R.M.; Drez, P.E.; Myers, J.; Tyburski, J.R.

1987-12-01

The Brine Sampling and Evaluation Program (BSEP) Phase II Report is an interim report which updates the data released in the BSEP Phase I Report. Direct measurements and observations of the brine that seeps into the WIPP repository excavations were continued through the period between August 1986 and July 1987. That data is included in Appendix A, which extends the observation period for some locations to approximately 900 days. Brine observations at 87 locations are presented in this report. Although WIPP underground workings are considered ''dry,'' small amounts of brine are present. Part of that brine migrates into the repository in response to pressure gradients at essentially isothermal conditions. The data presented in this report is a continuation of moisture content studies of the WIPP facility horizon that were initiated in 1982, as soon as underground drifts began to be excavated. Brine seepages are manifested by salt efflorescences, moist areas, and fluid accumulations in drillholes. 35 refs., 6 figs., 11 tabs

On the time-dependent behavior of a cylindrical salt dome with a high-level waste repository

International Nuclear Information System (INIS)

Prij, J.

1988-01-01

In a salt dome with a repository for high-level radioactive and heat-generating waste, thermal stresses develop. These stresses can influence the isolation capability of the salt dome if these stresses can initiate cracks or introduce movements along existing closed flaws. The influence of the thermomechanical properties of the rock salt and the surrounding rocks on the thermal stresses and the surface rise is discussed. This discussion is based on a number of finite element creep analyses of a homogeneous cylindrical salt dome. The parameters, varied in the analyses, are constants in the thermomechanical constitutive behavior of salt and rocks, and furthermore the thermal loading has been varied. It is shown that variations in the creep properties, which result in differences in creep strain rate of a factor of 100, have only a very limited influence on the thermal stresses and the surface rise. Of more importance is the elastic stiffness of the materials. In all creep analyses the thermal stresses in the salt are compressive and the shear stresses remain below 2 MPa. The results are evaluated using an analytical treatment. Based on this evaluation, it is shown that the observed trends in the numerical results have a more general character and are not strictly limited to the geometry chosen. It is concluded that the thermal stresses in the salt formation are not strongly dependent on the creep properties of the rock salt

Hanford Tank Waste to WIPP - Maximizing the Value of our National Repository Asset

Energy Technology Data Exchange (ETDEWEB)

Tedeschi, Allan R.; Wheeler, Martin

2013-11-11

Preplanning scope for the Hanford tank transuranic (TRU) waste project was authorized in 2013 by the Department of Energy (DOE) Office of River Protection (ORP) after a project standby period of eight years. Significant changes in DOE orders, Hanford contracts, and requirements at the Waste Isolation Pilot Plant (WIPP) have occurred during this time period, in addition to newly implemented regulatory permitting, re-evaluated waste management strategies, and new commercial applications. Preplanning has identified the following key approaches for reactivating the project: qualification of tank inventory designations and completion of all environmental regulatory permitting; identifying program options to accelerate retrieval of key leaking tank T-111; planning fully compliant implementation of DOE Order 413.3B, and DOE Standard 1189 for potential on-site treatment; and re-evaluation of commercial retrieval and treatment technologies for better strategic bundling of permanent waste disposal options.

Hanford Tank Waste to WIPP - Maximizing the Value of our National Repository Asset

International Nuclear Information System (INIS)

Tedeschi, Allan R.; Wheeler, Martin

2013-01-01

Preplanning scope for the Hanford tank transuranic (TRU) waste project was authorized in 2013 by the Department of Energy (DOE) Office of River Protection (ORP) after a project standby period of eight years. Significant changes in DOE orders, Hanford contracts, and requirements at the Waste Isolation Pilot Plant (WIPP) have occurred during this time period, in addition to newly implemented regulatory permitting, re-evaluated waste management strategies, and new commercial applications. Preplanning has identified the following key approaches for reactivating the project: qualification of tank inventory designations and completion of all environmental regulatory permitting; identifying program options to accelerate retrieval of key leaking tank T-111; planning fully compliant implementation of DOE Order 413.3B, and DOE Standard 1189 for potential on-site treatment; and re-evaluation of commercial retrieval and treatment technologies for better strategic bundling of permanent waste disposal options

Assessment of the potential for karst in the Rustler Formation at the WIPP site

International Nuclear Information System (INIS)

Lorenz, John Clay

2006-01-01

. Several surficial depressions at WIPP, suggested to be sinkholes, do not have enough catchment area to form a sinkhole, and holes drilled to investigate the subsurface strata do not support a sinkhole interpretation. Surface drainage across the WIPP site is poorly developed because it has been disrupted by migrating sand dunes and because precipitation is not focused by defined catchment areas in this region of low precipitation and low-dip bedding, not because it has been captured by sinkholes. There are no known points of discharge from the Rustler Formation at WIPP that would indicate the presence of a subsurface karst drainage system. The existing drillholes across the WIPP site, though small in diameter, are sufficient to assess the probability of karst development along the horizontal fractures that are common in the Rustler Formation, and the area of investigation has been augmented significantly by the mapping of four large-diameter shafts excavated into the WIPP repository. The general absence of dissolution, karsting, and related conduits is corroborated by the pumping tests which have interrogated large volumes of the Rustler Formation between drillholes. Diffusion calculations suggest that separate isotopic signatures for the water found in the fractures and the water found in the pores of the matrix rock between fractures are unlikely, thus the isotopic evidence for ancient Rustler formation waters is valid. Geophysical techniques show a number of anomalies, but the anomalies do not overlap to portray consistent and mutually supporting patterns that can be definitively related to karst void space at any given location. The coincidence of the Culebra and Magenta potentiometric heads between Nash Draw and the WIPP site is the inevitable intersection of two non-parallel surfaces rather than an indication of karst-related hydraulic communication between the two units. The proponents of karst in the Rustler Formation at the WIPP site tend to mix data, to take data

Assessment of the potential for karst in the Rustler Formation at the WIPP site.

Energy Technology Data Exchange (ETDEWEB)

Lorenz, John Clay

2006-01-01

. Several surficial depressions at WIPP, suggested to be sinkholes, do not have enough catchment area to form a sinkhole, and holes drilled to investigate the subsurface strata do not support a sinkhole interpretation. Surface drainage across the WIPP site is poorly developed because it has been disrupted by migrating sand dunes and because precipitation is not focused by defined catchment areas in this region of low precipitation and low-dip bedding, not because it has been captured by sinkholes. There are no known points of discharge from the Rustler Formation at WIPP that would indicate the presence of a subsurface karst drainage system. The existing drillholes across the WIPP site, though small in diameter, are sufficient to assess the probability of karst development along the horizontal fractures that are common in the Rustler Formation, and the area of investigation has been augmented significantly by the mapping of four large-diameter shafts excavated into the WIPP repository. The general absence of dissolution, karsting, and related conduits is corroborated by the pumping tests which have interrogated large volumes of the Rustler Formation between drillholes. Diffusion calculations suggest that separate isotopic signatures for the water found in the fractures and the water found in the pores of the matrix rock between fractures are unlikely, thus the isotopic evidence for ancient Rustler formation waters is valid. Geophysical techniques show a number of anomalies, but the anomalies do not overlap to portray consistent and mutually supporting patterns that can be definitively related to karst void space at any given location. The coincidence of the Culebra and Magenta potentiometric heads between Nash Draw and the WIPP site is the inevitable intersection of two non-parallel surfaces rather than an indication of karst-related hydraulic communication between the two units. The proponents of karst in the Rustler Formation at the WIPP site tend to mix data, to take data

Geomechanical applications for the Waste Isolation Pilot Plant (WIPP) project

International Nuclear Information System (INIS)

Matalucci, R.V.; Hunter, T.O.

1981-01-01

The Waste Isolation Pilot Plant (WIPP) is a research and development facility in bedded salt addressing the technical issues associated with the demonstration of disposal of radioactive waste from the defense programs of the USA. The geomechanical program includes laboratory experimentation, constitutive model and computer code development, and in-situ experimentation. Various material models, including creep for salt, and techniques for predicting room response under thermal and mechanical loads have been developed and are being applied to experiment and facility designs. A Benchmark II study has been conducted to compare the capabilities of nine structural codes to predict response of underground configuration under ambient temperature and with a thermal load of 7.5 W/m 2 . Parametric studies are being conducted to evaluate optimum room configurations. A series of in situ experiments is the next step towards validating models and predictive techniques. These experiments will be conducted in a facility in southeastern New Mexico mined at a depth of 659 m

Use of MgO to mitigate the effect of microbial CO2 production in the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Wang, Y.; Brush, L.H.

1997-01-01

The Waste Isolation Pilot Plant (WIPP), located in a salt bed in southern New Mexico, is designed by US Department of Energy to demonstrate the safe and permanent disposal of design-basis transuranic waste. WIPP performance assessment requires consideration of radionuclide release in brines in the event of inadvertent human intrusion. The mobility of radionuclides depends on chemical factors such as brine pmH (-log molality of H + ) and CO 2 fugacity. According to current waste inventory estimates, a large quantity (∼ 10 9 moles C) of organic materials will be emplaced in the WIPP. Those organic material will potentially be degraded by halophilic or halotolerant microorganisms in the presence of liquid water in the repository, especially if a large volume of brine is introduced into the repository by human intrusions. Organic material biodegradation will produce a large amount of CO 2 , which will acidify the WIPP brine and thus significantly increase the mobility of actinides. This communication addresses (1) the rate of organic material biodegradation and the quantity of CO 2 to be possibly generated, (2) the effect of microbial CO 2 production on overall WIPP performance, and (3) the mechanism of using MgO to mitigate this effect

Executive-style briefings on selected repository design issues

International Nuclear Information System (INIS)

1978-01-01

This document is a collection of executive-style briefings on selected repository design issues. Most of the briefings discuss differences between the US repository design bases presented in US Working Draft on Repository Physical Descriptions in a Salt Formation, prepared in support of INFCE discussions of May 1978 and the FRG-Netherlands design bases, presented in Design Study of a Radioactive Waste Repository to be Mined in a Medium-Size Salt Dome by Hamstra and Velzeboer, Netherlands Energy Research Foundation, January 1978. Advantages and disadvantages of the two sets of design bases are discussed, and the impacts of adopting either of these bases on the other's programs and positions are identified

Evaluation of the WIPP Project's compliance with the EPA radiation protection standards for disposal of transuranic waste

International Nuclear Information System (INIS)

Neill, R.H.; Chaturvedi, L.; Rucker, D.F.; Silva, M.K.; Walker, B.A.; Channell, J.K.; Clemo, T.M.

1998-03-01

The US Environmental Protection Agency's (EPA) proposed rule to certify that the Waste Isolation Pilot Plant (WIPP) meets compliance with the long-term radiation protection standards for geologic repositories (40CFR191 Subparts B and C), is one of the most significant milestones to date for the WIPP project in particular, and for the nuclear waste issue in general. The Environmental Evaluation Group (EEG) has provided an independent technical oversight for the WIPP project since 1978, and is responsible for many improvements in the location, design, and testing of various aspects of the project, including participation in the development of the EPA standards since the early 1980s. The EEG reviewed the development of documentation for assessing the WIPP's compliance by the Sandia National Laboratories following the 1985 promulgation by EPA, and provided many written and verbal comments on various aspects of this effort, culminating in the overall review of the 1992 performance assessment. For the US Department of Energy's (DOE) compliance certification application (CCA), the EEG provided detailed comments on the draft CCA in March, 1996, and additional comments through unpublished letters in 1997 (included as Appendices 8.1 and 8.2 in this report). Since the October 30, 1997, publication of the EPA's proposed rule to certify WIPP, the EEG gave presentations on important issues to the EPA on December 10, 1997, and sent a December 31, 1997 letter with attachments to clarify those issues (Appendix 8.3). The EEG has raised a number of questions that may have an impact on compliance. In spite of the best efforts by the EEG, the EPA reaction to reviews and suggestions has been slow and apparently driven by legal considerations. This report discusses in detail the questions that have been raised about containment requirements. Also discussed are assurance requirements, groundwater protection, individual protection, and an evaluation of EPA's responses to EEG's comments

WIPP conceptual design report. Addendum L. Mine safety code review for Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

1977-06-01

An initial review of New Mexico and Federal mining standards and regulations has been made to determine their applicability to the WIPP conceptual design. These standards and regulations are reviewed point by point and the enclosed listing includes comments and recommendations for those which will affect the design and/or eventual operations of WIPP. The majority of the standards, both federal and state, are standard safe mining practices. Those standards are listed which are thought should be emphasized for development of the design; also those that would increase the hazard risk by strict compliance. Because the WIPP facility is different in many respects from mines for which the regulations were intended, strict compliance in some respects would provide an increased hazard, while in other instances the regulations are less strict than is desirable. These are noted in the attached review

Salt disposal of heat-generating nuclear waste

International Nuclear Information System (INIS)

Leigh, Christi D.; Hansen, Francis D.

2011-01-01

This report summarizes the state of salt repository science, reviews many of the technical issues pertaining to disposal of heat-generating nuclear waste in salt, and proposes several avenues for future science-based activities to further the technical basis for disposal in salt. There are extensive salt formations in the forty-eight contiguous states, and many of them may be worthy of consideration for nuclear waste disposal. The United States has extensive experience in salt repository sciences, including an operating facility for disposal of transuranic wastes. The scientific background for salt disposal including laboratory and field tests at ambient and elevated temperature, principles of salt behavior, potential for fracture damage and its mitigation, seal systems, chemical conditions, advanced modeling capabilities and near-future developments, performance assessment processes, and international collaboration are all discussed. The discussion of salt disposal issues is brought current, including a summary of recent international workshops dedicated to high-level waste disposal in salt. Lessons learned from Sandia National Laboratories' experience on the Waste Isolation Pilot Plant and the Yucca Mountain Project as well as related salt experience with the Strategic Petroleum Reserve are applied in this assessment. Disposal of heat-generating nuclear waste in a suitable salt formation is attractive because the material is essentially impermeable, self-sealing, and thermally conductive. Conditions are chemically beneficial, and a significant experience base exists in understanding this environment. Within the period of institutional control, overburden pressure will seal fractures and provide a repository setting that limits radionuclide movement. A salt repository could potentially achieve total containment, with no releases to the environment in undisturbed scenarios for as long as the region is geologically stable. Much of the experience gained from United

Salt disposal of heat-generating nuclear waste.

Energy Technology Data Exchange (ETDEWEB)

Leigh, Christi D. (Sandia National Laboratories, Carlsbad, NM); Hansen, Francis D.

2011-01-01

This report summarizes the state of salt repository science, reviews many of the technical issues pertaining to disposal of heat-generating nuclear waste in salt, and proposes several avenues for future science-based activities to further the technical basis for disposal in salt. There are extensive salt formations in the forty-eight contiguous states, and many of them may be worthy of consideration for nuclear waste disposal. The United States has extensive experience in salt repository sciences, including an operating facility for disposal of transuranic wastes. The scientific background for salt disposal including laboratory and field tests at ambient and elevated temperature, principles of salt behavior, potential for fracture damage and its mitigation, seal systems, chemical conditions, advanced modeling capabilities and near-future developments, performance assessment processes, and international collaboration are all discussed. The discussion of salt disposal issues is brought current, including a summary of recent international workshops dedicated to high-level waste disposal in salt. Lessons learned from Sandia National Laboratories' experience on the Waste Isolation Pilot Plant and the Yucca Mountain Project as well as related salt experience with the Strategic Petroleum Reserve are applied in this assessment. Disposal of heat-generating nuclear waste in a suitable salt formation is attractive because the material is essentially impermeable, self-sealing, and thermally conductive. Conditions are chemically beneficial, and a significant experience base exists in understanding this environment. Within the period of institutional control, overburden pressure will seal fractures and provide a repository setting that limits radionuclide movement. A salt repository could potentially achieve total containment, with no releases to the environment in undisturbed scenarios for as long as the region is geologically stable. Much of the experience gained from

Structural testing of salt loaded HEPA filters for WIPP

International Nuclear Information System (INIS)

Smith, P.R.; Leslie, I.H.; Hensel, E.C.; Shultheis, T.M.; Walls, J.R.

1993-01-01

The ventilation studies of the Waste Isolation Pilot Plant described in this paper were performed by personnel from New Mexico State Univ. in collaboration with Sandia National Laboratories, Los Alamos National Laboratory and Westinghouse Corporation. High efficiency particulate air filters (0.61m by 0.61m by 0.3m) of the type in use at the Waste Isolation Pilot Plant were loaded with salt aerosol provided from that site. The structural strength of salt-loaded, high-efficiency filters was investigated at two humidity levels, high (75%RH) and low (13-14% RH), by subjecting the filters to pressure transients of the types expected from tornadoes. Filters loaded under the high humidity condition proved to have a greater structural strength than did the filters loaded under the low humidity conditions, when both types were subjected to tornado-like pressure pulses. This unexpected results was apparently due to the crystallization of salt upon the wire face guard of the HEPA filter loaded under the high humidity condition which kept salt from penetrating the filter medium while still providing a substantial pressure drop at the standard flow rate. Results are also presented for HEPA filters pre-conditioned at 100% RH before structural testing and for HEPA filters in series with pre-filters

Instrumentation of the thermal/structural interactions in situ tests at the Waste Isolation Pilot Plant (WIPP)

Energy Technology Data Exchange (ETDEWEB)

Munson, D.E. [Sandia National Labs., Albuquerque, NM (United States). Repository Isolation Systems Div.; Hoag, D.L.; Blankenship, D.A.; DeYonge, W.F.; Schiermeister, D.M. [RE/SPEC, Inc., Albuquerque, NM (United States); Jones, R.L.; Baird, G.T. [Tech Reps, Inc., Albuquerque, NM (United States)

1997-04-01

The Department of Energy has constructed the Waste Isolation Pilot Plant (WIPP) to develop the technology for the disposal of radioactive waste from defense programs. Sandia National Laboratories had the responsibility for the experimental activities at the WIPP and fielded several large-scale Thermal/Structural Interactions (TSI) in situ tests to validate techniques used to predict repository performance. The instrumentation of these tests involved the placement of over 4,200 gages including room closure gages, borehole extensometers, stress gages, borehole inclinometers, fixed reference gages, borehole strain gages, thermocouples, thermal flux meters, heater power gages, environmental gages, and ventilation gages. Most of the gages were remotely read instruments that were monitored by an automated data acquisition system, but manually read instruments were also used to provide early deformation information and to provide a redundancy of measurement for the remote gages. Instruments were selected that could operate in the harsh environment of the test rooms and that could accommodate the ranges of test room responses predicted by pretest calculations. Instruments were tested in the field prior to installation at the WIPP site and were modified to improve their performance. Other modifications were made to gages as the TSI tests progressed using knowledge gained from test maintenance. Quality assurance procedures were developed for all aspects of instrumentation including calibration, installation, and maintenance. The instrumentation performed exceptionally well and has produced a large quantity of quality information.

Instrumentation of the thermal/structural interactions in situ tests at the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Munson, D.E.; Jones, R.L.; Baird, G.T.

1997-04-01

The Department of Energy has constructed the Waste Isolation Pilot Plant (WIPP) to develop the technology for the disposal of radioactive waste from defense programs. Sandia National Laboratories had the responsibility for the experimental activities at the WIPP and fielded several large-scale Thermal/Structural Interactions (TSI) in situ tests to validate techniques used to predict repository performance. The instrumentation of these tests involved the placement of over 4,200 gages including room closure gages, borehole extensometers, stress gages, borehole inclinometers, fixed reference gages, borehole strain gages, thermocouples, thermal flux meters, heater power gages, environmental gages, and ventilation gages. Most of the gages were remotely read instruments that were monitored by an automated data acquisition system, but manually read instruments were also used to provide early deformation information and to provide a redundancy of measurement for the remote gages. Instruments were selected that could operate in the harsh environment of the test rooms and that could accommodate the ranges of test room responses predicted by pretest calculations. Instruments were tested in the field prior to installation at the WIPP site and were modified to improve their performance. Other modifications were made to gages as the TSI tests progressed using knowledge gained from test maintenance. Quality assurance procedures were developed for all aspects of instrumentation including calibration, installation, and maintenance. The instrumentation performed exceptionally well and has produced a large quantity of quality information

Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Chapter D, Appendix D1 (conclusion): Volume 3, Revision 1.0

Energy Technology Data Exchange (ETDEWEB)

1992-06-01

This report, Part B (Vol. 3) of the permit application for the WIPP facility, contains information related to the site characterization of the facility, including geology, design, rock salt evaluations, maps, drawings, and shaft excavations. (CBS)

The Rustler Formation at the WIPP [Waste Isolations Pilot Plant] site: Report of a workshop on the geology and hydrology of the Rustler Formation as it relates to the WIPP Project

International Nuclear Information System (INIS)

Chaturvedi, L.

1987-02-01

This workshop contained eight papers characterizing the Rustler Formation at the WIPP site in New Mexico. Four of these reports were processed separately for the data bases. Information contained in the four remaining papers is available in journal articles or in the reports of other conferences and included discussions of ground water flow through the Rustler Formation, the potential migration of leached radionuclides in this rock, the effects of mineral dissolution on the removal of underlying salt deposits, and a possible pathway for radionuclide migration into the biosphere

QA lessons learned for parameter control from the WIPP Project

International Nuclear Information System (INIS)

Richards, R.R.

1998-01-01

This paper provides a summary of lessons learned from experiences on the Waste Isolation Pilot Plant (WJPP) Project in implementation of quality assurance controls surrounding inputs for performance assessment analysis. Since the performance assessment (PA) process is inherent in compliance determination for any waste repository, these lessons-learned are intended to be useful to investigators, analysts, and Quality Assurance (QA) practitioners working on high level waste disposal projects. On the WIPP Project, PA analyses for regulatory-compliance determination utilized several inter-related computer programs (codes) that mathematically modeled phenomena such as radionuclide release, retardation, and transport. The input information for those codes are the parameters that are the subject of this paper. Parameters were maintained in a computer database, which was then queried electronically by the PA codes whenever input was needed as the analyses were run

Shaft seals for final high-level radioactive waste repositories. ELSA. Pt. 1; Schachtverschluesse fuer Endlager fuer hochradioaktive Abfaelle. ELSA. T. 1

Energy Technology Data Exchange (ETDEWEB)

Kudla, W.; Schreiter, F.; Gruner, M. [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Bergbau und Spezialtiefbau; Jobmann, M.; Bollingerfehr, W.; Mueller-Hoeppe, N.; Herold, P. [DBE Technology GmbH, Peine (Germany)

2013-04-30

The state of the art in science and technology fir shaft seals with long-term stability is summarized regarding their applicability for high-level waste repository in Germany. The concepts and drafts for the shaft sealing systems ERAM, Asse, Konrad, the WIPP side, the RESEAL concept, the NAGRA concept and the project LASA are reviewed. The methodology of applying partial factors in a safety analysis is summarized and the applicability of this method for geotechnical sealing structures is confirmed. To establish geomechanical boundary conditions of the host rocks and clay stone the stress-strain behavior of the rock mass adjoining the shaft has to be identified including time-dependent thermo-mechanical processes. The general and special requirements for the design of shaft sealing systems, especially in salt rock and clay formations are described, derived from the safety requirements (BMU 2010). Finally general information needs were identified.

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, vertical emplacement mode: Volume 1

International Nuclear Information System (INIS)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packing, and other surface facility operations are described. Operations in the shafts underground are described, including waste hoisting, transfer, and vertical emplacement. This report specifically addresses the vertical emplacement mode, the reference design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, vertical emplacement mode: Volume 1

Energy Technology Data Exchange (ETDEWEB)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packing, and other surface facility operations are described. Operations in the shafts underground are described, including waste hoisting, transfer, and vertical emplacement. This report specifically addresses the vertical emplacement mode, the reference design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs.

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, horizontal emplacment mode: Volume 1

International Nuclear Information System (INIS)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packaging, and other surface facility operations are described. Operations in the shafts and underground are described, including waste hoisting, transfer, and horizontal emplacement. This report specifically addresses the horizontal emplacement mode, the passive alternate design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs

Hydrostatic and shear consolidation tests with permeability measurements on Waste Isolation Pilot Plant crushed salt

International Nuclear Information System (INIS)

Brodsky, N.S.

1994-03-01

Crushed natural rock salt is a primary candidate for use as backfill and barrier material at the Waste Isolation Pilot Plant (WIPP) and therefore Sandia National Laboratories (SNL) has been pursuing a laboratory program designed to quantify its consolidation properties and permeability. Variables that influence consolidation rate that have been examined include stress state and moisture content. The experimental results presented in this report complement existing studies and work in progress conducted by SNL. The experiments described in this report were designed to (1) measure permeabilities of consolidated specimens of crushed salt, (2) determine the influence of brine saturation on consolidation under hydrostatic loads, and 3) measure the effects of small applied shear stresses on consolidation properties. The laboratory effort consisted of 18 individual tests: three permeability tests conducted on specimens that had been consolidated at Sandia, six hydrostatic consolidation and permeability tests conducted on specimens of brine-saturated crushed WIPP salt, and nine shear consolidation and permeability tests performed on crushed WIPP salt specimens containing 3 percent brine by weight. For hydrostatic consolidation tests, pressures ranged from 1.72 MPa to 6.90 MPa. For the shear consolidation tests, confining pressures were between 3.45 MPa and 6.90 MPa and applied axial stress differences were between 0.69 and 4.14 MPa. All tests were run under drained conditions at 25 degrees C

WIPP Pecos Management Reports

Science.gov (United States)

These reviews and evaluations compiled by Pecos Management Services, Inc. encompass the current and future WIPP activities in the program areas of TRU waste characterization, transportation, and disposal.

Sandia studies of high-level waste canisters and overpacks applicable for a salt repository

International Nuclear Information System (INIS)

Molecke, M.A.; Schaefer, D.W.; Glass, R.S.; Ruppen, J.A.

1982-01-01

An experimental program to develop candidate materials for use as high-level waste (HLW) overpacks or canisters in a salt repository has been in progress at Sandia National Laboratories since 1976. The main objective of this program is to provide a waste package barrier having a long lifetime in the chemical and physical environment of a repository. This paper summarizes the recent corrosion and metallurgical study results for the prime overpack material, TiCode-12, in the areas of uniform corrosion (extremely low rate and extent); local attack, e.g., pits and crevices (none were found); stress corrosion cracking susceptibility (no significant changes in macroscopic tensile properties were detected); hydrogen sorption-embrittlement effects; effects of gamma irradiation in solution; and sensitization effects (testing is still in process in the last three areas). Previous candidate screening analyses on other alloys and recent work on alternate overpack alloys are reviewed. All phases of these interrelated laboratory, hot-cell, and field experimental studies are described. 16 references, 8 figures, 4 tables

The interaction of Plutonium with Bacteria in the Repository Environment

International Nuclear Information System (INIS)

Gillow, J. B.; Francis, A. J.; Lucero, D. A.; Papenguth, H. W.

2000-01-01

Microorganisms in the nuclear waste repository environment may interact with plutonium through (1) sorption, (2) intracellular accumulation, and (3) transformation speciation. These interactions may retard or enhance the mobility of Pu by precipitation reactions, biocolloid formation, or production of more soluble species. Current and planned radioactive waste repository environments, such as deep subsurface halite and granite formations, are considered extreme relative to life processes in the near-surface terrestrial environment. There is a paucity of information on the biotransformation of radionuclides by microorganisms present in such extreme environments. In order to gain a better understanding of the interaction of plutonium with microorganisms present in the waste repository sites we investigated a pure culture (Halomonas sp.) and a mixed culture of bacteria (Haloarcula sinaiiensis, Marinobacter hydrocarbonoclasticus, Altermonas sp., and a γ-proteobacterium) isolated from the Waste Isolation Pilot Plant (WIPP) site and an Acetobacterium sp. from alkaline groundwater at the Grimsel Test Site in Switzerland

Deep geologic disposal of mixed waste in bedded salt: The Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Rempe, N.T.

1993-01-01

Mixed waste (i.e., waste that contains both chemically hazardous and radioactive components) poses a moral, political, and technical challenge to present and future generations. But an international consensus is emerging that harmful byproducts and residues can be permanently isolated from the biosphere in a safe and environmentally responsible manner by deep geologic disposal. To investigate and demonstrate such disposal for transuranic mixed waste, derived from defense-related activities, the US Department of Energy has prepared the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico. This research and development facility was excavated approximately at the center of a 600 m thick sequence of salt (halite) beds, 655 m below the surface. Proof of the long-term tectonic and hydrological stability of the region is supplied by the fact that these salt beds have remained essentially undisturbed since they were deposited during the Late Permian age, approximately 225 million years ago. Plutonium-239, the main radioactive component of transuranic mixed waste, has a half-life of 24,500 years. Even ten half-lives of this isotope - amounting to about a quarter million years, the time during which its activity will decline to background level represent only 0.11 percent of the history of the repository medium. Therefore, deep geologic disposal of transuranic mixed waste in Permian bedded salt appears eminently feasible

Brine: a computer program to compute brine migration adjacent to a nuclear waste canister in a salt repository

International Nuclear Information System (INIS)

Duckworth, G.D.; Fuller, M.E.

1980-01-01

This report presents a mathematical model used to predict brine migration toward a nuclear waste canister in a bedded salt repository. The mathematical model is implemented in a computer program called BRINE. The program is written in FORTRAN and executes in the batch mode on a CDC 7600. A description of the program input requirements and output available is included. Samples of input and output are given

Geoprospective study of a nuclear waste repository: salt domes; Bibliographic study of their genesis

International Nuclear Information System (INIS)

Billaux, D.; Robelin, C.

1985-01-01

This report appraises, from the results of a bibliographical study, the possibility of beginning of a domal rise from the salt layer in which or above which would have been placed a repository. The physical mecanisms of salt creep are first screened, together with the factors determining their intensity and relative importance. These factors are primarily the temperature and the state of stress. Semi empirical laws are given for some mecanisms. Present knowledge about the state of the salt in the ground are then examined: we are not able to satisfactorily calculate ''in situ'' stresses, or to explain the existence of an important shear stress, that has been pointed out by most of the stress measurements. The retrospective study of the genesis of existing domes brings an insight into their correlation with sedimentary and tectonic phases. Model studies help us to interpret the distances between domes, and to explain the scale of this phenomenon. After recapitulating the various factors of some importance, we find that the probability of a dome rise from a previously static layer is low, in the time lap we are interested in (100 000 years). Such a rise would have to be triggered by important changes in the sedimentation, erosion or tectonic activity on the site

Brine transport studies in the bedded salt of the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

McTigue, D.F.; Nowak, E.J.

1987-01-01

Brine flow has been measured to unheated boreholes for periods of a few days and to heated holes for two years in the WIPP facility. It is suggested that Darcy flow may dominate the observed influx of brine. Exact solutions to a linearized model for one-dimensional, radial flow are evaluated for conditions approximating the field experiments. Flow rates of the correct order of magnitude are calculated for permeabilities in the range 10 -21 to 10 -20 m 2 (1 to 10 nanodarcy) for both the unheated and heated cases. 20 refs., 3 figs., 1 tab

WIPP site and vicinity geological field trip. A report of a field trip to the proposed Waste Isolation Pilot Plant project in Southeastern New Mexico, June 16 to 18, 1980

Energy Technology Data Exchange (ETDEWEB)

Chaturvedi, L

1980-10-01

The Environmental Evaluation Group is conducting an assessment of the radiological health risks to people from the Waste Isolation Pilot Plant. As a part of this work, EEG is making an effort to improve the understanding of those geological issues concerning the WIPP site which may affect the radiological consequences of the proposed repository. One of the important geological issues to be resolved is the timing and the nature of the dissolution processes which may have affected the WIPP site. EEG organized a two-day conference of geological scientists, on January 17-18, 1980. On the basis of the January conference and the June field trip, EEG has formed the following conclusions: (1) it has not been clearly established that the site or the surrounding area has been attacked by deep dissolution to render it unsuitable for the nuclear waste pilot repository; (2) the existence of an isolated breccia pipe at the site unaccompanied by a deep dissolution wedge, is a very remote possibility; (3) more specific information about the origin and the nature of the brine reservoirs is needed. An important question that should be resolved is whether each encounter with artesian brine represents a separate pocket or whether these occurrences are interconnected; (4) Anderson has postulated a major tectonic fault or a fracture system at the Basin margin along the San Simon Swale; (5) the area in the northern part of the WIPP site, identified from geophysical and bore hole data as the disturbed zone, should be further investigated to cleary understand the nature and significance of this structural anomaly; and (6) a major drawback encountered during the discussions of geological issues related to the WIPP site is the absence of published material that brings together all the known information related to a particular issue.

WIPP Compliance Certification Application calculations parameters. Part 1: Parameter development

International Nuclear Information System (INIS)

Howarth, S.M.

1997-01-01

The Waste Isolation Pilot Plant (WIPP) in southeast New Mexico has been studied as a transuranic waste repository for the past 23 years. During this time, an extensive site characterization, design, construction, and experimental program was completed, which provided in-depth understanding of the dominant processes that are most likely to influence the containment of radionuclides for 10,000 years. Nearly 1,500 parameters were developed using information gathered from this program; the parameters were input to numerical models for WIPP Compliance Certification Application (CCA) Performance Assessment (PA) calculations. The CCA probabilistic codes frequently require input values that define a statistical distribution for each parameter. Developing parameter distributions begins with the assignment of an appropriate distribution type, which is dependent on the type, magnitude, and volume of data or information available. The development of the parameter distribution values may require interpretation or statistical analysis of raw data, combining raw data with literature values, scaling of lab or field data to fit code grid mesh sizes, or other transformation. Parameter development and documentation of the development process were very complicated, especially for those parameters based on empirical data; they required the integration of information from Sandia National Laboratories (SNL) code sponsors, parameter task leaders (PTLs), performance assessment analysts (PAAs), and experimental principal investigators (PIs). This paper, Part 1 of two parts, contains a discussion of the parameter development process, roles and responsibilities, and lessons learned. Part 2 will discuss parameter documentation, traceability and retrievability, and lessons learned from related audits and reviews

Design, modeling, and current interpretations of the H-19 and H-11 tracer tests at the WIPP site

International Nuclear Information System (INIS)

Meigs, L.C.; Beauheim, R.L.; McCord, J.T.; Tsang, Y.W.; Haggerty, R.

1996-01-01

Site-characterization studies at the Waste Isolation Pilot Plant (WIPP) site in southeastern New Mexico, US identified ground-water flow in the Culebra Dolomite Member of the Rustler Formation as the most likely geologic pathway for radionuclide transport to the accessible environment in the event of a breach of the WIPP repository through inadvertent human intrusion. The results of recent tracer tests, as well as hydraulic tests, laboratory measurements, and re-examination of Culebra geology and stratigraphy, have led to a significant refinement of the conceptual model for transport in the Culebra. Tracer test results and geologic observations suggest that flow occurs within fractures, and to some extent within interparticle porosity and vugs connected by microfractures. Diffusion occurs within all connected porosity. Numerical simulations suggest that the data from the tracer tests cannot be simulated with heterogeneous single-porosity models; significant matrix diffusion appears to be required. The low permeability and lack of significant tracer recovery from tracers injected into the upper Culebra suggest that transport primarily occurs in the lower Culebra

Nuclear waste repository design and construction

International Nuclear Information System (INIS)

Bohlke, B.M.; Monsees, J.E.

1987-01-01

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt

The WIPP transportation system: Demonstrated readiness

International Nuclear Information System (INIS)

Ward, T.R.; Spooner, R.

1991-01-01

The Department of Energy (DOE) has developed an integrated transportation system to transport transuranic (TRU) waste from ten widely-dispersed generator sites to the Waste Isolation Pilot Plant (WIPP). The system consists of a Type B container, a specially- designed trailer, a lightweight tractor, the DOE ''TRANSCOM'' vehicle tracking system, and uniquely qualified and highly-trained drivers. In June of 1989, the National Academy of Sciences reviewed the transportation system and concluded that: ''The system proposed for transportation of TRU waste to WIPP is safer than that employed for any other hazardous material in the United States today and will reduce risk to very low levels'' (emphasis added). The next challenge facing the DOE was demonstrating that this system was ready to transport the TRU waste to the WIPP site efficiently and in the safest manner possible. Not only did the DOE feel that is was necessary to convince itself that the system was safe, but also representatives of the 20 states through which it would travel

The WIPP transportation system: Demonstrated readiness

International Nuclear Information System (INIS)

Ward, T.R.; Spooner, R.

1991-01-01

The Department of Energy (DOE) has developed an integrated transportation system to transport transuranic (TRU) waste from ten widely-dispersed generator sites to the Waste Isolation Pilot Plant (WIPP). The system consists of a Type B container, a specially-designed trailer, a lightweight tractor, the DOE ''TRANSCOM'' vehicle tracing system, and uniquely qualified and highly-trained drivers. In June of 1989, the National Academy of Sciences reviewed the transportation system and concluded that: ''The system proposed for transportation of TRU waste to WIPP is safer than that employed for any other hazardous material in the United States today and will reduce risk to very low levels.'' The next challenge facing the DOE was demonstrating that this system was ready to transport the TRU waste to the WIPP site in the safest manner possible. Not only did the DOE feel that it was necessary to convince itself that the system was safe, but also representatives of the 23 states through which it traveled

Formation and fate of gases in the caverns of a repository in salt rock

International Nuclear Information System (INIS)

Mueller, W.; Morlock, G.; Gronemeyer, C.

1992-01-01

The report summarizes the knowledge avaible today of the mechanisms governing the formation and transport of gases in a salt mine repository for radioactive wastes. The work under review deals with the formation of gases-by way of radiolysis, corrosion, microbial degradation, thermally induced or primary gas generation - and analyses the efficiency of predicting and modelling the gas generation mechanisms in terms of the role of parameters involved, and accuracy. Existing gaps in available knowledge are shown and defined in terms of significance, leading to an analysis of interdependencies between the various mechanisms and to a statement concerning the necessity of establishing materials balances. (orig./EF) [de

Studies of mechanisms and processes of relevance to the safety of nuclear waste repositories, as carried out prior to, during and after flovelling of the Hope potash salt mine

International Nuclear Information System (INIS)

1985-01-01

Studies on the effects of a hypothetical accident involving water or brine intrusion into a waste repository in a salt mine are of special importance within the framework of safety assessments of salt formations as candidate sites for nuclear waste repositories. The measuring activities under review include the following: Physicochemical measurements for determining dissolution and recipitation of salts, transport mechanisms, temperature curves, natural build-up and efficiency of geochemical barriers in the brine. Geochemical measurements for obtaining information on the rock deformation prior to, during, and after flovelling. Geophysical measurements of microseismic behaviour of rock masses prior to, during, and after flovelling. Examination of an artificial barrier structure for the testing and assessment of technical barriers and their efficiency. (orig./HP) [de

Proposed waste isolation pilot project (WIPP) and impacts in the state of New Mexico: a socio-economic analysis. Final report

International Nuclear Information System (INIS)

Cummings, R.D.; Burness, H.S.; Norton, R.D.

1981-04-01

This document is a final report for research conducted concerning the socio-economic impacts in the State of New Mexico that might attend the construction and operation of the proposed Waste Isolation Pilot Plant (WIPP). The proposed site for the WIPP, known as the Los Medanos site, is in Southeastern New Mexico's Eddy County, some 25 miles east of Carlsbad, New Mexico and some 40 miles from Hobbs, New Mexico, in adjacent Lea County. The purpose as set out in the US Department of Energy's environmental impact statements is for storage of TRU waste from the US defense program and the construction of a research and development area for experiments concerning the isolation of all types of nuclear waste in salt. The intended purpose of the study is to identify, measure (when possible) and assess the range of potential socio-economic impacts in the State that may be attributable to the WIPP. Every effort has been made by the authors to approach this task in an objective manner. In efforts to provide an objective analysis of the WIPP, however, particular attention was required in providing a comprehensive review of potential impacts. This means that however unlikely an impact might seem, the authors have purposely avoided pre-judging the potential magnitude of the impact and have applied their best efforts to measure it. On the other hnd, this study is not intended to provide a definitive calculation regarding the net balance of WIPP-related benefits and costs. To help ensure objectivity, two advisory boards, Technical Advisory Board and Public Advisory Board, were formed at the outset of the project for the purpose of providing periodic reviews of research efforts

Arthropod and decomposition studies at the WIPP site, October-November, 1980

International Nuclear Information System (INIS)

Anon.

1981-01-01

These studies were conducted to address topics related to potential environmental impacts resulting from WIPP construction at the Los Medanos site. Studies include the effect of salt piles on soil microarthropod faunas and soil community respiration, quantities of soil moved from deep in the soil column to the surface by termites and ants, and development and testing of a multiple regression model for predicting decomposition. Soil cores were taken at increasing distances from the twenty-year-old salt dump at the Nash Draw Potash facility and examined for microarthropod content and tested for other biological activity. Although there were some reductions in densities of most taxa at the base of the salt pile and at 100 m from the base, all of the dominant soil taxa from the area were found at the base of the pile. If a substantial adverse impact occurred soon after emplacement of the salt, recovery has been relatively complete. Substantial changes in these baseline population densities during or after construction could be indicators of impact to the ecology of the Los Medanos site. A model was developed to predict rates of decomposition of shinnery oak litter based on evapotranspiration and lignin content. The model was less successful in predicting the decomposition rate of creosotebush litter, as removal of litter by termites produced large variances in apparent decomposition rates

Technical basis for external dosimetry at the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Bradley, E.W.; Wu, C.F.; Goff, T.E.

1993-01-01

The WIPP External Dosimetry Program, administered by Westinghouse Electric Corporation, Waste Isolation Division, for the US Department of Energy (DOE), provides external dosimetry support services for operations at the Waste Isolation Pilot Plant (WIPP) Site. These operations include the receipt, experimentation with, storage, and disposal of transuranic (TRU) wastes. This document describes the technical basis for the WIPP External Radiation Dosimetry Program. The purposes of this document are to: (1) provide assurance that the WIPP External Radiation Dosimetry Program is in compliance with all regulatory requirements, (2) provide assurance that the WIPP External Radiation Dosimetry Program is derived from a sound technical base, (3) serve as a technical reference for radiation protection personnel, and (4) aid in identifying and planning for future needs. The external radiation exposure fields are those that are documented in the WIPP Final Safety Analysis Report

Salton Sea Geothermal Field, California, as a near-field natural analog of a radioactive waste repository in salt

International Nuclear Information System (INIS)

Elders, W.A.; Cohen, L.H.

1983-11-01

Since high concentrations of radionuclides and high temperatures are not normally encountered in salt domes or beds, finding an exact geologic analog of expected near-field conditions in a mined nuclear waste repository in salt will be difficult. The Salton Sea Geothermal Field, however, provides an opportunity to investigate the migration and retardation of naturally occurring U, Th, Ra, Cs, Sr and other elements in hot brines which have been moving through clay-rich sedimentary rocks for up to 100,000 years. The more than thirty deep wells drilled in this field to produce steam for electrical generation penetrate sedimentary rocks containing concentrated brines where temperatures reach 365 0 C at only 2 km depth. The brines are primarily Na, K, Ca chlorides with up to 25% of total dissolved solids; they also contain high concentrations of metals such as Fe, Mn, Li, Zn, and Pb. This report describes the geology, geophysics and geochemistry of this system as a prelude to a study of the mobility of naturally occurring radionuclides and radionuclide analogs within it. The aim of this study is to provide data to assist in validating quantitative models of repository behavior and to use in designing and evaluating waste packages and engineered barriers. 128 references, 33 figures, 13 tables

Salton Sea Geothermal Field, California, as a near-field natural analog of a radioactive waste repository in salt

Energy Technology Data Exchange (ETDEWEB)

Elders, W.A.; Cohen, L.H.

1983-11-01

Since high concentrations of radionuclides and high temperatures are not normally encountered in salt domes or beds, finding an exact geologic analog of expected near-field conditions in a mined nuclear waste repository in salt will be difficult. The Salton Sea Geothermal Field, however, provides an opportunity to investigate the migration and retardation of naturally occurring U, Th, Ra, Cs, Sr and other elements in hot brines which have been moving through clay-rich sedimentary rocks for up to 100,000 years. The more than thirty deep wells drilled in this field to produce steam for electrical generation penetrate sedimentary rocks containing concentrated brines where temperatures reach 365/sup 0/C at only 2 km depth. The brines are primarily Na, K, Ca chlorides with up to 25% of total dissolved solids; they also contain high concentrations of metals such as Fe, Mn, Li, Zn, and Pb. This report describes the geology, geophysics and geochemistry of this system as a prelude to a study of the mobility of naturally occurring radionuclides and radionuclide analogs within it. The aim of this study is to provide data to assist in validating quantitative models of repository behavior and to use in designing and evaluating waste packages and engineered barriers. 128 references, 33 figures, 13 tables.

Approach to first principles model prediction of measured WIPP [Waste Isolation Pilot Plant] in situ room closure in salt

International Nuclear Information System (INIS)

Munson, D.E.; Fossum, A.F.; Senseny, P.E.

1989-01-01

The discrepancies between predicted and measured WIPP in situ Room D closures are markedly reduced through the use of a Tresca flow potential, an improved small strain constitutive model, an improved set of material parameters, and a modified stratigraphy. 17 refs., 8 figs., 1 tab

Geological status of NWTS repository siting activities in the paradox basin

International Nuclear Information System (INIS)

Frazier, N.A.; Conwell, F.R.

1981-01-01

Emplacement of waste packages in mined geological repositories is one method being evaluated for isolating high-level nuclear wastes. Granite, dome salt, tuff, basalt and bedded salt are among the rock types being investigated. Described in this paper is the status of geological activities in the Paradox Basin of Utah and Colorado, one region being explored as a part of the National Waste Terminal Storage (NWTS) program to site a geological repository in bedded salt

Safety and performance indicators for repositories in salt and clay formations

International Nuclear Information System (INIS)

Wolf, Jens; Ruebel, Andre; Noseck, Ulrich; Becker, Dirk

2008-07-01

The GRS (Gesellschaft fuer Reaktorsicherheit) study aims to the identification of suitable indicators for repositories in salt and clay formation. It is not intended to compare the two formations with respect to the safe disposal of radioactive waste. A first set of safety and performance indicators for both host rocks has been derived on the basis of results of the SPIN project. Reference values for the safety indicators have been determined. The suitability of the indicators and their significance for different time frames Is demonstrated by means of deterministic model calculations and external parameter variations of previous studies. The safety indicators considered in the report are the effective dose rate (Sv/a), the radiotoxicity concentration in the biosphere water (Sv/m 3 ) and the radiotoxicity flux from the geosphere (overlying rock) (Sv/a). The performance indicators considered in the study are the radiotoxicity inventory in different compartments (S), radiotoxicity fluxes from compartments and the integrated radiotoxicity fluxes from compartments (Sv).

The Geologic and Hydrogeologic Setting of the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Swift, P.N.; Corbet, T.F.

1999-01-01

The Waste Isolation Pilot Plant (WIPP) is a mined repository constructed by the US Department of Energy for the permanent disposal of transuranic wastes generated since 1970 by activities related to national defense. The WIPP is located 42 km east of Carlsbad, New Mexico, in bedded salt (primarily halite) of the Late Permian (approximately 255 million years old) Salado Formation 655 m below the land surface. Characterization of the site began in the mid-1970s. Construction of the underground disposal facilities began in the early 1980s, and the facility received final certification from the US Environmental Protection Agency in May 1998. Disposal operations are planned to begin following receipt of a final permit from the State of New Mexico and resolution of legal issues. Like other proposed geologic repositories for radioactive waste, the WIPP relies on a combination of engineered and natural barriers to isolate the waste from the biosphere. Engineered barriers at the WIPP, including the seals that will be emplaced in the access shafts when the facility is decommissioned, are discussed in the context of facility design elsewhere in this volume. Physical properties of the natural barriers that contribute to the isolation of radionuclides are discussed here in the context of the physiographic, geologic, and hydrogeologic setting of the site

Basic data report for drillhole AEC 8 (Waste Isolation Pilot Plant - WIPP)

International Nuclear Information System (INIS)

1983-01-01

AEC 8 was originally drilled in 1974 to a depth of 3028 ft by Oak Ridge National Laboratory as part of the initial investigations of a site for radioactive waste disposal. In 1976, Sandia National Laboratories deepened the borehole from the top of the Castile Formation into the Bell Canyon Formation to test the hydraulic properties of the Bell Canyon. The borehole encountered in descending order Holocene sands (20 ft), Mescalero caliche (6 ft), Santa Rosa Sandstone (143 ft), Dewey Lake Redbeds (491 ft), Rustler Formation (322 ft), Salado Formation (1990 ft), Castile Formation (1335 ft), and the upper Bell Canyon Formation (603 ft). The borehole stratigraphy is in normal order and there is no significant deformation. An extensive suite of geophysical logs provides information on the lithology and stratigraphy. The potentiometric surfaces of Bell Canyon fluid-bearing zones are 550 ft (for the zone at 4821 ft to 4827 ft) and 565 ft below land surface (for the zone at 4844 to 4860 ft). The WIPP is a demonstration facility for the disposal of transuranic (TRU) waste from defense programs. The WIPP will also provide a research facility to investigate the interactions between bedded salt and high level wastes

WIPP conceptual design report. Addendum C. Cost worksheets for Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

1977-04-01

The cost worksheets for the Waste Isolation Pilot Plant (WIPP) are presented. A summary cost estimate, cost estimate for surface facilities, and cost estimate for shafts and underground facilities are included

In situ permeability testing of rock salt

International Nuclear Information System (INIS)

Peterson, E.W.; Lagus, P.L.; Broce, R.D.; Lie, K.

1981-04-01

Storage of transuranic (TRU) wastes in bedded salt formations requires a knowledge of the in situ permeability of SENM rock salt. Since assumptions for safety assessments have been made in which these wastes could generate gas pressures on the order of the lithostatic pressure over geologic time scales, the permeability of the surrounding formation becomes an important parameter for determining the manner in which the gases will be contained or dispersed. This report describes the series of tests conducted in the AEC-7 borehole, located near the WIPP site, to determine the in situ gas flow characteristics of the bedded salt. In these tests, compressed air was injected into the borehole and flow into the surrounding formation measured. These measured flow rates were interpreted in terms of formation permeabilities and porosities which were, in turn, used as modeling parameters for the repository response analysis. Two series of field tests were performed. The first series consisted of a number of whole-hole flow tests conducted to provide preliminary design information required for future operation of a guarded straddle packer system capable of measuring permeabilities > or = 0.1 μdarcy. The second series of tests were conducted using the Systems, Science and Software (S-Cubed) designed guarded straddle packer system. In these interval permeability tests, 100-foot lengths of borehole were isolated and the flow characteristics of the surrounding formation examined. In this report, a complete description of the test procedures, instrumentation, and measurement techniques is first given. The analytical/numerical methods used for data interpretation are then presented, followed by results of the interval and permeability tests. (The whole-hole tests are summarized in Appendix A.) Conclusions are presented in the final section

Proceedings of the 6th US/German Workshop on Salt Repository Research, Design, and Operation

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Steininger, Walter [Karlsruhe Inst. of Technology (KIT) (Germany); Bollingerfehr, Wilhelm [DBE Technology GmbH, Peine (Germany)

2016-01-11

The 6th US/German Workshop on Salt Repository Research, Design, and Operation was held in Dresden. Germany on September 7-9, 2015. Over seventy participants helped advance the technical basis for salt disposal of radioactive waste. The number of collaborative efforts continues to grow and to produce useful documentation, as well as to define the state of the art for research areas. These Proceedings are divided into Chapters, and a list of authors is included in the Acknowledgement Section. Also in this document are the Technical Agenda, List of Participants, Biographical Information, Abstracts, and Presentations. Proceedings of all workshops and other pertinent information are posted on websites hosted by Sandia National Laboratories and the Nuclear Energy Agency Salt Club. The US/German workshops provide continuity for long-term research, summarize and publish status of mature areas, and develop appropriate research by consensus in a workshop environment. As before, major areas and findings are highlighted, which constitute topical Chapters in these Proceedings. In total, the scientific breadth is substantial and while not all subject matter is elaborated into chapter format, all presentations and abstracts are published in this document. In the following Proceedings, six selected topics are developed in detail.

A regional water balance for the WIPP site and surrounding area

International Nuclear Information System (INIS)

Hunter, R.L.

1987-01-01

A water balance or budget is developed as an accounting of the components of a closed hydrologic system. In the WIPP study area, water-budget techniques have previously been used to compute leakage from Lake Avalon and from potash refinery spoil ponds. A general expression for a closed hydrologic system is presented. In a developed area like the WIPP region, the water budget must include many usage factors, such as municipal or industrial pumpage. In the WIPP water-budget study area, inflows are precipitation, surface- and ground-water inflow, and the artificial addition of surface and ground water. Outflows are surface runoff, evaporation and transpiration, and ground-water outflow. Changes in storage in the WIPP region have also been documented. The WIPP water balance described here is based on a combination of long-term averages and figures for 1980. 12 refs., 5 figs., 1 tab

A sensitivity analysis of the WIPP disposal room model: Phase 1

Energy Technology Data Exchange (ETDEWEB)

Labreche, D.A.; Beikmann, M.A. [RE/SPEC, Inc., Albuquerque, NM (United States); Osnes, J.D. [RE/SPEC, Inc., Rapid City, SD (United States); Butcher, B.M. [Sandia National Labs., Albuquerque, NM (United States)

1995-07-01

The WIPP Disposal Room Model (DRM) is a numerical model with three major components constitutive models of TRU waste, crushed salt backfill, and intact halite -- and several secondary components, including air gap elements, slidelines, and assumptions on symmetry and geometry. A sensitivity analysis of the Disposal Room Model was initiated on two of the three major components (waste and backfill models) and on several secondary components as a group. The immediate goal of this component sensitivity analysis (Phase I) was to sort (rank) model parameters in terms of their relative importance to model response so that a Monte Carlo analysis on a reduced set of DRM parameters could be performed under Phase II. The goal of the Phase II analysis will be to develop a probabilistic definition of a disposal room porosity surface (porosity, gas volume, time) that could be used in WIPP Performance Assessment analyses. This report documents a literature survey which quantifies the relative importance of the secondary room components to room closure, a differential analysis of the creep consolidation model and definition of a follow-up Monte Carlo analysis of the model, and an analysis and refitting of the waste component data on which a volumetric plasticity model of TRU drum waste is based. A summary, evaluation of progress, and recommendations for future work conclude the report.

Coupled multiphase flow and closure analysis of repository response to waste-generated gas at the Waste Isolation Pilot Plant (WIPP)

Energy Technology Data Exchange (ETDEWEB)

Freeze, G.A.; Larson, K.W. [INTERA Inc., Austin, TX (United States); Davies, P.B. [Sandia National Laboratories, Albuquerque, NM (United States)

1995-10-01

A long-term assessment of the Waste Isolation Pilot Plant (WIPP) repository performance must consider the impact of gas generation resulting from the corrosion and microbial degradation of the emplaced waste. A multiphase fluid flow code, TOUGH2/EOS8, was adapted to model the processes of gas generation, disposal room creep closure, and multiphase (brine and gas) fluid flow, as well as the coupling between the three processes. System response to gas generation was simulated with a single, isolated disposal room surrounded by homogeneous halite containing two anhydrite interbeds, one above and one below the room. The interbeds were assumed to have flow connections to the room through high-permeability, excavation-induced fractures. System behavior was evaluated by tracking four performance measures: (1) peak room pressure; (2) maximum brine volume in the room; (3) total mass of gas expelled from the room; and (4) the maximum gas migration distance in an interbed. Baseline simulations used current best estimates of system parameters, selected through an evaluation of available data, to predict system response to gas generation under best-estimate conditions. Sensitivity simulations quantified the effects of parameter uncertainty by evaluating the change in the performance measures in response to parameter variations. In the sensitivity simulations, a single parameter value was varied to its minimum and maximum values, representative of the extreme expected values, with all other parameters held at best-estimate values. Sensitivity simulations identified the following parameters as important to gas expulsion and migration away from a disposal room: interbed porosity; interbed permeability; gas-generation potential; halite permeability; and interbed threshold pressure. Simulations also showed that the inclusion of interbed fracturing and a disturbed rock zone had a significant impact on system performance.

Coupled multiphase flow and closure analysis of repository response to waste-generated gas at the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

Freeze, G.A.; Larson, K.W.; Davies, P.B.

1995-10-01

A long-term assessment of the Waste Isolation Pilot Plant (WIPP) repository performance must consider the impact of gas generation resulting from the corrosion and microbial degradation of the emplaced waste. A multiphase fluid flow code, TOUGH2/EOS8, was adapted to model the processes of gas generation, disposal room creep closure, and multiphase (brine and gas) fluid flow, as well as the coupling between the three processes. System response to gas generation was simulated with a single, isolated disposal room surrounded by homogeneous halite containing two anhydrite interbeds, one above and one below the room. The interbeds were assumed to have flow connections to the room through high-permeability, excavation-induced fractures. System behavior was evaluated by tracking four performance measures: (1) peak room pressure; (2) maximum brine volume in the room; (3) total mass of gas expelled from the room; and (4) the maximum gas migration distance in an interbed. Baseline simulations used current best estimates of system parameters, selected through an evaluation of available data, to predict system response to gas generation under best-estimate conditions. Sensitivity simulations quantified the effects of parameter uncertainty by evaluating the change in the performance measures in response to parameter variations. In the sensitivity simulations, a single parameter value was varied to its minimum and maximum values, representative of the extreme expected values, with all other parameters held at best-estimate values. Sensitivity simulations identified the following parameters as important to gas expulsion and migration away from a disposal room: interbed porosity; interbed permeability; gas-generation potential; halite permeability; and interbed threshold pressure. Simulations also showed that the inclusion of interbed fracturing and a disturbed rock zone had a significant impact on system performance

Basic data report for drillhole ERDA 9 (Waste Isolation Pilot Plant WIPP)

International Nuclear Information System (INIS)

1983-01-01

ERDA 9 was drilled in eastern Eddy County, New Mexico, to investigate and test salt beds for the disposal of nuclear wastes. The hole was placed near the SE corner of section 20, T22S,R31E. It was drilled between April 28 and June 4, 1976, to a depth of 2889 ft (measured from a kelly bushing altitude of 3,420.4 ft MSL). The borehole encountered, from top to bottom, Holocene deposits (including artificial fill) of 22 ft, the Pleistocene Mescalero Caliche (5 ft) and Gatuna Formation (27 ft), 9 ft of the Triassic Santa Rosa Sandstone, and 487 ft of the Dewey Lake Red Beds, 290 ft of the Rustler Formation, 1976 ft of the Salado Formation and 53 ft of the Castile Formation, all of Permian age. Cuttings were collected at 5-ft intervals for the land surface to a depth of 1090 ft, and consecutive cores were taken to a depth of 2876.6 ft. A suite of wireline geophysical logs was run the full length of the borehole to measure distribution of radioactive elements and hydrogen, and variations in rock density and elastic velocity. On the basis of the borehole findings and related hydrological and geophysical programs, the site was judged suitable to pursue the extensive geological characterization program which followed. The core from ERDA 9 provided a suite of samples extensively tested for rock mechanics, physical properties, and mineralogy. Drill-stem tests in ERDA 9 indicated no significant fluids or permeability in the Salado beds of interest. The WIPP is a demonstration facility for the disposal of transuranic (TRU) waste from defense programs. The WIPP will also provide a research facility to investigate the interactions between bedded salt and high level wastes

Independent monitoring of a release from the waste isolation pilot plant in New Mexico, USA. Results and purpose

Energy Technology Data Exchange (ETDEWEB)

Thakur, Punam; Ballard, Sally [Carlsbad Environmental Monitoring and Research Center, Carlsbad, NM (United States)

2015-07-01

The Waste Isolation Pilot Plant (WIPP) is a transuranic (TRU) waste repository operated by the U.S. Department of Energy (DOE). The repository is emplacing defense-related transuranic (TRU) wastes into a bedded salt formation approximately 655 m (2150 ft.) below the surface of the Earth. Located near Carlsbad, New Mexico, an area with less than 30,000 people, the WIPP facility is licensed to accept TRU waste with activity concentrations of alpha-emitting isotopes >3700 Bq/m{sup 3} (> 100 nCi/g) and half-life >20 years. The upper waste acceptance limit is 0.85 TBq/liter (<23 Ci/liter) of total activity and 10 Sv/hr dose rate on contact. The repository, which opened in March 1999 will eventually contain the equivalent of ∝176,000 m{sup 3} of TRU waste. The vast majority of the waste disposed in the WIPP repository is ''contact-handled'' waste, meaning it has a surface dose rate less than 2 mSv per hour. Local acceptance of WIPP is in part due to an independent environmental monitoring program that began before and continues after WIPP began receiving nuclear waste. This independent monitoring is being conducted by the Carlsbad Environmental Monitoring and Research Center (CEMRC), which is associated with New Mexico State University. CEMRC is funded by DOE through a grant process that respects its independence in carrying out and reporting the results of environmental monitoring at and near the WIPP site. The primary focus of CEMRC monitoring is on airborne radioactive particulate; however other pathways are also monitored. Pre-disposal baseline data of various anthropogenic radionuclides present in the WIPP environment is essential for the proper evaluation of the WIPP integrity. These data are compared against disposal phase data to assess whether or not there is any radiological impact from the presence of WIPP on workers and on the regional public. The program has capabilities to detect radionuclides rapidly in case of accidental releases

Geoscience data base handbook for modeling a nuclear waste repository. Volume 1

International Nuclear Information System (INIS)

Isherwood, D.

1979-12-01

This handbook contains reference information on parameters that should be considered in analyzing or modeling a proposed nuclear waste repository site. Only those parameters and values that best represent the natural environment are included. Rare extremes are avoided. Where laboratory and field data are inadequate, theoretical treatments and informed engineering judgements are presented. Volume 1 contains a data base on salt as a repository medium. Chapters on the geology of bedded and dome salt, the geomechanics of salt, hydrology, geochemistry, natural and man-made features, and seismology provide compiled data and related information useful for studying a proposed repository in salt. These and other data will be needed to derive generic deep geologic modeling parameters and will also serve as background for the verification of source data that may be presented in licensing applications for nuclear waste repositories. Volume 2 is the result of a scoping study for a data base on the geology, geomechanics, and hydrology of shale, granite, and basalt as alternative repository media. Except for the geomechanics of shale, most of the sections contain relatively complete compilations of the available data, as well as discussions of the properties that are unique to each rock type

Probabilistic risk assessment for salt repository conceptual design of subsurface facilities: A techical basis for Q-list determination

International Nuclear Information System (INIS)

Chen, C.P.; Mayberry, J.J.; Shepherd, J.; Koza, H.; Rahmani, H.; Sinsky, J.

1987-12-01

Subpart G ''Quality Assurance'' of 10 CFR Part 60 requires that the US Department of Energy (DOE) apply a quality assurance program to ''all systems, structures, and components important to safety'' and to ''design and characterization of barriers important to waste isolation.'' In April 1986, DOE's Office of Geologic Repositories (OGR) issued general guidance for formulating a list of such systems, structures, and components---the Q-list. This guidance called for the use of probabilistic risk assessment (PRA) techniques to identify Q-list items. In this report, PRA techniques are applied to the underground facilities and systems described in the conceptual design report for the Salt Repository Project (SRP) in Deaf Smith County, Texas. Based on probability and dose consequence calculations, no specific items were identified for the Q-list. However, evaluation of the analyses indicated that two functions are important in precluding off-site releases of radioactivity: disposal container integrity; and isolation of the underground facility by the heating, ventilation, and air conditioning (HVAC) systems. Items related to these functions are recommended for further evaluation as the repository design progresses. 13 refs., 20 figs

Results from simulated contact-handled transuranic waste experiments at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Molecke, M.A.; Sorensen, N.R.; Krumhansl, J.L.

1993-01-01

We conducted in situ experiments with nonradioactive, contact-handled transuranic (CH TRU) waste drums at the Waste Isolation Pilot Plant (WIPP) facility for about four years. We performed these tests in two rooms in rock salt, at WIPP, with drums surrounded by crushed salt or 70 wt % salt/30 wt % bentonite clay backfills, or partially submerged in a NaCl brine pool. Air and brine temperatures were maintained at ∼40C. These full-scale (210-L drum) experiments provided in situ data on: backfill material moisture-sorption and physical properties in the presence of brine; waste container corrosion adequacy; and, migration of chemical tracers (nonradioactive actinide and fission product simulants) in the near-field vicinity, all as a function of time. Individual drums, backfill, and brine samples were removed periodically for laboratory evaluations. Waste container testing in the presence of brine and brine-moistened backfill materials served as a severe overtest of long-term conditions that could be anticipated in an actual salt waste repository. We also obtained relevant operational-test emplacement and retrieval experience. All test results are intended to support both the acceptance of actual TRU wastes at the WIPP and performance assessment data needs. We provide an overview and technical data summary focusing on the WIPP CH TRU envirorunental overtests involving 174 waste drums in the presence of backfill materials and the brine pool, with posttest laboratory materials analyses of backfill sorbed-moisture content, CH TRU drum corrosion, tracer migration, and associated test observations

Concentration of uranium in the drinking and surface water around the WIPP site

International Nuclear Information System (INIS)

Khaing, H.; Lemons, B.G.; Thakur, P.

2016-01-01

Activity concentration of uranium isotopes ( 238 U, 234 U and 235 U) were analyzed in drinking and surface water samples collected in the vicinity of the WIPP site using alpha spectroscopy. The purpose of this study was to investigate the changes in uranium concentrations (if any) in the vicinity of the WIPP site and whether the February 14, 2014 radiation release event at the WIPP had any detectable impact on the water bodies around the WIPP. (author)

Technical bases for establishing a salt test facility

International Nuclear Information System (INIS)

1985-05-01

The need for a testing facility in which radioactive materials may be used in an underground salt environment is explored. No such facility is currently available in salt deposits in the United States. A salt test facility (STF) would demonstrate the feasibility of safely storing radioactive waste in salt and would provide data needed to support the design, construction, licensing, and operation of a radioactive waste repository in salt. Nineteen issues that could affect long-term isolation of waste materials in a salt repository are identified from the most pertinent recent literature. The issues are assigned an overall priority and a priority relative to the activities of the STF. Individual tests recommended for performance in the STF to resolve the 19 issues are described and organized under three groups: waste package performance, repository design and operation, and site characterization and evaluation. The requirements for a salt test facility are given in the form of functional criteria, and the approach that will be used in the design, execution, interpretation, and reporting of tests is discussed

Evaporite dissolution relevant to the WIPP site, northern Delaware Basin, southeastern New Mexico

International Nuclear Information System (INIS)

Lambert, S.J.

1982-01-01

Evaluation of the threat of natural dissolution of host evaporites to the integrity of the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico has taken into consideration (1) the volume of missing rock salt, (2) the occurrence (or not) of characteristic dissolution brines, (3) geomorphic features, some of which are unrelated to dissolution, and (4) the time intervals over which dissolution may have been active. Even under the assumption that all missing halite was originally present and has been removed by dissolution, there is no evidence of active preferential removal of the lower Salado Formation halite by any geologically reasonable process. The geologic record contains evidence of dissolution in the Triassic and Jurassic; to constrain all removal of basinal halite to the late Cenozoic yields an unrealistically high rate of removal. Application to the lower Salado of a stratabound mechanism known to be active in Nash Draw, a near-surface feature within the Basin, allows a minimum survival time of 2,500,000 years to be predicted for the subsurface facility for storage of radioactive waste at WIPP. This calculation is based on an analysis of all known dissolution features in the Delaware Basin, and takes into account the wetter (pluvial) climate during the past 600,000 years. 2 figures, 1 table

Progress in long-lived radioactive waste management and disposal at the waste isolation pilot plant

International Nuclear Information System (INIS)

Triay, I.R.; Matthews, M.L.; Eriksson, L.G.

2001-01-01

The Salado Formation is buried more than 350 m beneath the sands and cacti of the Chihuahuan Desert and hosts the Waste Isolation Pilot Plant (WIPP) deep geological repository at a depth of approximately 650 m. Since the WIPP repository is at least 10 years ahead of any other repository development for long-lived radioactive waste, other radioactive waste management organizations and institutions could benefit both scientifically and politically from sharing the lessons learned at WIPP. Benefits would include using existing expertise and facilities to cost-effectively address and solve program-specific issues and to train staff. The characteristics of the WIPP repository and infrastructure are described in this paper. (author)

Progress in long-lived radioactive waste management and disposal at the waste isolation pilot plant

Energy Technology Data Exchange (ETDEWEB)

Triay, I R; Matthews, M L [U.S. Dept. of Energy Carlsbad Field Office, New Mexico (United States); Eriksson, L G [GRAM, Inc., Albuquerque, NM (United States)

2001-07-01

The Salado Formation is buried more than 350 m beneath the sands and cacti of the Chihuahuan Desert and hosts the Waste Isolation Pilot Plant (WIPP) deep geological repository at a depth of approximately 650 m. Since the WIPP repository is at least 10 years ahead of any other repository development for long-lived radioactive waste, other radioactive waste management organizations and institutions could benefit both scientifically and politically from sharing the lessons learned at WIPP. Benefits would include using existing expertise and facilities to cost-effectively address and solve program-specific issues and to train staff. The characteristics of the WIPP repository and infrastructure are described in this paper. (author)

Buckling design criteria for waste package disposal containers in mined salt repositories: Technical report

International Nuclear Information System (INIS)

Mallett, R.H.

1986-12-01

This report documents analytical and experimental results from a survey of the technical literature on buckling of thick-walled cylinders under external pressure. Based upon these results, a load factor is suggested for the design of waste package containers for disposal of high-level radioactive waste in repositories mined in salt formations. The load factor is defined as a ratio of buckling pressure to allowable pressure. Specifically, a load factor which ranges from 1.5 for plastic buckling to 3.0 for elastic buckling is included in a set of proposed buckling design criteria for waste disposal containers. Formulas are given for buckling design under axisymmetric conditions. Guidelines are given for detailed inelastic buckling analyses which are generally required for design of disposal containers

WIPP's Hazardous Waste Facility Permit Renewal Application

International Nuclear Information System (INIS)

Most, W.A.; Kehrman, R.F.

2009-01-01

Hazardous waste permits issued by the New Mexico Environment Department (NMED) have a maximum term of 10-years from the permit's effective date. The permit condition in the Waste Isolation Pilot Plant's (WIPP) Hazardous Waste Facility Permit (HWFP) governing renewal applications, directs the Permittees to submit a permit application 180 days prior to expiration of the Permit. On October 27, 1999, the Secretary of the NMED issued to the United States Department of Energy (DOE), the owner and operator of WIPP, and to Washington TRU Solutions LLC (WTS), the Management and Operating Contractor and the cooperator of WIPP, a HWFP to manage, store, and dispose hazardous waste at WIPP. The DOE and WTS are collectively known as the Permittees. The HWFP is effective for a fixed term not to exceed ten years from the effective date of the Permit. The Permittees may renew the HWFP by submitting a new permit application at least 180 calendar days before the expiration date, of the HWFP. The Permittees are not proposing any substantial changes in the Renewal Application. First, the Permittees are seeking the authority to dispose of Contact-Handled and Remote-Handled TRU mixed waste in Panel 8. Panels 4 through 7 have been approved in the WIPP Hazardous Waste Facility Permit as it currently exists. No other change to the facility or to the manner in which hazardous waste is characterized, managed, stored, or disposed is being requested. Second, the Permittees also seek to include the Mine Ventilation Rate Monitoring Plan, as Attachment Q in the HWFP. This Plan has existed as a separate document since May 2000. The NMED has requested that the Plan be submitted as part of the Renewal Application. The Permittees have been operating to the Mine Ventilation Rate Monitoring Plan since the Plan was submitted. Third, some information submitted in the original WIPP RCRA Part B Application has been updated, such as demographic information. The Permittees will submit this information in the

Crack closure and healing studies in WIPP [Waste Isolation Pilot Plant] salt using compressional wave velocity and attenuation measurements: Test methods and results

International Nuclear Information System (INIS)

Brodsky, N.S.

1990-11-01

Compressional wave ultrasonic data were used to qualitatively assess the extent of crack closure during hydrostatic compression of damaged specimens of WIPP salt. Cracks were introduced during constant strain-rate triaxial tests at low confining pressure (0.5 MPa) as specimens were taken to either 0.5, 1.0, or 1.5 percent axial strain. For three specimens taken to 1.0 percent axial strain, the pressure was increased to 5, 10 or 15 MPa. For the remaining specimens, pressure was raised to 15 MPa. Waveforms for compressional waves traveling both parallel and perpendicular to the direction of maximum principal stress were measured in the undamaged state, during constant strain-rate tests, and then monitored as functions of time while the specimens were held at pressure. Both wave velocities and amplitudes increased over time at pressure, indicating that cracks closed and perhaps healed. The recovery of ultrasonic wave characteristics depended upon both pressure and damage level. The higher the pressure, the greater the velocity recovery; however, amplitude recovery showed no clear correlation with pressure. For both amplitudes and velocities, recoveries were greatest in the specimens with the least damage. 13 refs., 15 figs., 1 tab

Correlation of Creep Behavior of Domal Salts

International Nuclear Information System (INIS)

Munson, D.E.

1999-01-01

The experimentally determined creep responses of a number of domal salts have been reported in, the literature. Some of these creep results were obtained using standard (conventional) creep tests. However, more typically, the creep data have come from multistage creep tests, where the number of specimens available for testing was small. An incremental test uses abrupt changes in stress and temperature to produce several time increments (stages) of different creep conditions. Clearly, the ability to analyze these limited data and to correlate them with each other could be of considerable potential value in establishing the mechanical characteristics of salt domes, both generally and specifically. In any analysis, it is necessary to have a framework of rules to provide consistency. The basis for the framework is the Multimechanism-Deformation (M-D) constitutive model. This model utilizes considerable general knowledge of material creep deformation to supplement specific knowledge of the material response of salt. Because the creep of salt is controlled by just a few micromechanical mechanisms, regardless of the origin of the salt, certain of the material parameters are values that can be considered universal to salt. Actual data analysis utilizes the methodology developed for the Waste Isolation Pilot Plant (WIPP) program, and the response of a bedded pure WIPP salt as the baseline for comparison of the domal salts. Creep data from Weeks Island, Bryan Mound, West Hackberry, Bayou Choctaw, and Big Hill salt domes, which are all sites of Strategic Petroleum Reserve (SPR) storage caverns, were analyzed, as were data from the Avery Island, Moss Bluff, and Jennings salt domes. The analysis permits the parameter value sets for the domal salts to be determined in terms of the M-D model with various degrees of completeness. In turn this permits detailed numerical calculations simulating cavern response. Where the set is incomplete because of the sparse database, reasonable

Environmental monitoring and cooperative resource management at the WIPP site

International Nuclear Information System (INIS)

1992-01-01

This poster session by the Environmental Monitoring Section of the US DOE Waste Isolation Pilot Plant is to demonstrate that the DOE is committed to sound environmental management. This WIPP poster session demonstrates radiological as well as nonradiological environmental monitoring activities conducted routinely at the WIPP. And how data collected prior to the WIPP being operational is used to establish a preoperational baseline for environmental studies in which the samples collected during the operational phase will be compared. Cooperative Resource Management is a relatively new concept for governments agencies. It allows two or more agencies the ability to jointly share in funding a program or project and yet both agencies can benefit from the outcome. These programs are usually a biological type study. The WIPP cooperative agreement between the US BLM, DOE and its contractors is to continue the ongoing documentation of the diversity of the Chihuahuan desert

WIPP startup: Overcoming unprecedented challenges

International Nuclear Information System (INIS)

Hunt, Arlen E.

1992-01-01

Since its authorization by the U.S. Congress in Public Law 96-164, the Waste Isolation Pilot Plant Program has achieved significant progress. Subsequent to a Record of Decision based on the October 1980 Final Environmental Impact Statement (FEIS), the scientific and engineering challenge of constructing a 100-acre mined repository to demonstrate the safe and environmentally sound disposal of defense program generated transuranic waste became reality. Since initial conception, however, a complex program has evolved. Demonstration of compliance with the requirements of the Resource Conservation and Recovery Act (RCRA) and Environmental Protection Agency (EPA) disposal Standards defined in 10 CFR 191, Subpart B (yet to be repromulgated), became prerequisites to a disposal decision. On June 13, 1990, based on a supplement to the 1980 FEIS, the decision was made to redefine the program to include a formal test phase. This decision required an addendum to the Final Safety Analysis Report to assure commitment to safety considerations, an intensive operational readiness review effort, and the need for a No-Migration Determination for the Environmental Protection Agency. In addition to meeting the technical challenges, the need to satisfy a broad spectrum of oversight groups (some directly funded by the Department of Energy) was required. With the decision making process publicly displayed on the Secretary of Energy's Decision Plan, the unprecedented challenges of the WIPP Program were painstakingly met, one by one, in an accountable and visible manner. (author)

Salt drying: a low-cost, simple and efficient method for storing plants in the field and preserving biological repositories for DNA diversity research.

Science.gov (United States)

Carrió, Elena; Rosselló, Josep A

2014-03-01

Although a variety of methods have been optimized for the collection and storage of plant specimens, most of these are not suited for field expeditions for a variety of logistic reasons. Drying specimens with silica gel in polyethylene bags is currently the standard for field-sampling methods that are suitable for subsequent DNA extraction. However, silica-gel repositories are not readily available in remote areas, and its use is not very cost-effective for the long-term storage of collections or in developing countries with limited research budgets. Salting is an ancient and traditional drying process that preserves food samples by dehydrating tissues and inhibiting water-dependent cellular metabolism. We compared salt and silica-gel drying methods with respect to dehydration rates overtime, DNA quality and polymerase chain reaction(PCR) success to assess whether dry salting can be used as an effective plant preservation method for DNA analysis. Specimens from eleven plant species covering a variety of leaf structures, leaf thicknesses and water contents were analysed. Experimental work indicated that (i) levels of dehydration in sodium chloride were usually comparable to those obtained when silica gel was used, (ii) no spoilage, fungal or bacterial growth was observed for any of the species with all drying treatments and (iii) good yields of quality genomic DNA suitable for PCR applications were obtained in the salt-drying treatments. The preservation of plant tissues in commercial table salt appears to be a satisfactory, and versatile method that may be suitable in remote areas where cryogenic resources and silica repositories are not available. © 2013 John Wiley & Sons Ltd.

Disposal alternatives and recommendations for waste salt management for repository excavation in the Palo Duro Basin, Texas

International Nuclear Information System (INIS)

1987-01-01

This report documents an evaluation of five alternatives for the disposal of waste salt that would be generated by the construction of a repository for radioactive waste in underground salt deposits at either of two sites in the Palo Duro Basin, Texas. The alternatives include commercial disposal, offsite deep-well injection, disposal in abandoned mines, ocean disposal, and land surface disposal on or off the site. For each alternative a reference case was rated - positive, neutral, or negative - in terms of environmental and dependability factors developed specifically for Texas sites. The factors constituting the environmental checklist relate to water quality impact, water- and land-use conflicts, ecological compatibility, conformity with air quality standards, and aesthetic impact. Factors on the dependability check-list relate to public acceptance, the adequacy of site characterization, permit and licensing requirements, technological requirements, and operational availability. A comparison of the ratings yielded the following viable alternatives, in order of preference: (1) land surface disposal, specifically disposal on tailings piles associated with abandoned potash mines; (2) disposal in abandoned mines, specifically potash mines; and (3) commercial disposal. Approaches to the further study of these three salt management techniques are recommended

Groundwater monitoring at the waste isolation pilot plant

International Nuclear Information System (INIS)

Kehrman, R.; Broberg, K.; Tatro, G.; Richardson, R.; Dasczcyszak, W.

1990-01-01

This paper discusses the Groundwater Monitoring Program (GMP) being conducted at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. The Regulatory and Environmental Programs (REP) section of the Environment, Safety and Health department (ES ampersand H) is responsible for conducting environmental monitoring at the WIPP. Groundwater monitoring is one of the ongoing environmental activities currently taking place. The REP section includes water-quality sampling and water-level monitoring. The WIPP Project is a research and development facility designed to demonstrate the safe disposal of defense-generated TRU and mixed waste in a geologic repository. The Salado Formation of Permian age serves as the repository medium. The Salado Formation consists of bedded salt and associated evaporites. The formation is 602 meters thick at the site area; the top surface is located at a subsurface depth of 262 meters (10). The repository lies at a subsurface depth of 655 meters. Water-quality sampling for physical, chemical, and radiological parameters has been an ongoing activity at the WIPP site for the past six years, and will continue through the life of the project. Data collected from this program to date, has been used by Sandia National Laboratories for site characterization and performance assessment work. The data has also been used to establish a baseline of preoperational radiological and nonradiological groundwater quality. Once the facility begins receiving waste, this baseline will be used to determine if the WIPP facility influences or alters groundwater quality over time. The water quality of a well is determined while the well is continuously pumped. Serial samples of the pumped water are collected and tested for pH, Eh, temperature, specific gravity, specific conductivity, alkalinity, chlorides, divalent cations, ferrous iron, and total iron. 13 refs., 4 figs., 1 tab

Continuous Improvement and the Safety Case for the Waste Isolation Pilot Plant Geologic Repository - 13467

Energy Technology Data Exchange (ETDEWEB)

Van Luik, Abraham; Patterson, Russell; Nelson, Roger [US Department of Energy, Carlsbad Field Office, 4021 S. National parks Highway, Carlsbad, NM 88220 (United States); Leigh, Christi [Sandia National Laboratories Carlsbad Operations, 4100 S. National parks Highway, Carlsbad, NM 88220 (United States)

2013-07-01

The Waste Isolation Pilot Plant (WIPP) is a geologic repository 2150 feet (650 m) below the surface of the Chihuahuan desert near Carlsbad, New Mexico. WIPP permanently disposes of transuranic waste from national defense programs. Every five years, the U.S. Department of Energy (DOE) submits an application to the U.S. Environmental Protection Agency (EPA) to request regulatory-compliance re-certification of the facility for another five years. Every ten years, DOE submits an application to the New Mexico Environment Department (NMED) for the renewal of its hazardous waste disposal permit. The content of the applications made by DOE to the EPA for re-certification, and to the NMED for permit-renewal, reflect any optimization changes made to the facility, with regulatory concurrence if warranted by the nature of the change. DOE points to such changes as evidence for its having taken seriously its 'continuous improvement' operations and management philosophy. Another opportunity for continuous improvement is to look at any delta that may exist between the re-certification and re-permitting cases for system safety and the consensus advice on the nature and content of a safety case as being developed and published by the Nuclear Energy Agency's Integration Group for the Safety Case (IGSC) expert group. DOE at WIPP, with the aid of its Science Advisor and teammate, Sandia National Laboratories, is in the process of discerning what can be done, in a reasonably paced and cost-conscious manner, to continually improve the case for repository safety that is being made to the two primary regulators on a recurring basis. This paper will discuss some aspects of that delta and potential paths forward to addressing them. (authors)

Waste Isolation Pilot Plant Salt Decontamination Testing

Energy Technology Data Exchange (ETDEWEB)

Rick Demmer; Stephen Reese

2014-09-01

On February 14, 2014, americium and plutonium contamination was released in the Waste Isolation Pilot Plant (WIPP) salt caverns. At the request of WIPP’s operations contractor, Idaho National Laboratory (INL) personnel developed several methods of decontaminating WIPP salt, using surrogate contaminants and also americium (241Am). The effectiveness of the methods is evaluated qualitatively, and to the extent possible, quantitatively. One of the requirements of this effort was delivering initial results and recommendations within a few weeks. That requirement, in combination with the limited scope of the project, made in-depth analysis impractical in some instances. Of the methods tested (dry brushing, vacuum cleaning, water washing, strippable coatings, and mechanical grinding), the most practical seems to be water washing. Effectiveness is very high, and it is very easy and rapid to deploy. The amount of wastewater produced (2 L/m2) would be substantial and may not be easy to manage, but the method is the clear winner from a usability perspective. Removable surface contamination levels (smear results) from the strippable coating and water washing coupons found no residual removable contamination. Thus, whatever is left is likely adhered to (or trapped within) the salt. The other option that shows promise is the use of a fixative barrier. Bartlett Nuclear, Inc.’s Polymeric Barrier System (PBS) proved the most durable of the coatings tested. The coatings were not tested for contaminant entrapment, only for coating integrity and durability.

Test plan: Gas-threshold-pressure testing of the Salado Formation in the WIPP underground facility

International Nuclear Information System (INIS)

Saulnier, G.J. Jr.

1992-03-01

Performance assessment for the disposal of radioactive waste from the United States defense program in the WIPP underground facility must assess the role of post-closure was generation by waste degradation and the subsequent pressurization of the facility. be assimilated by the host formation will Whether or not the generated gas can be assimilated by the host formation will determine the ability of the gas to reach or exceed lithostatic pressure within the repository. The purpose of this test plan is (1) to present a test design to obtain realistic estimates of gas-threshold pressure for the Salado Formation WIPP underground facility including parts of the formation disturbed by the underground of the Salado, and (2) to provide a excavations and in the far-field or undisturbed part framework for changes and amendments to test objectives, practices, and procedures. Because in situ determinations of gas-threshold pressure in low-permeability media are not standard practice, the methods recommended in this testplan are adapted from permeability-testing and hydrofracture procedures. Therefore, as the gas-threshold-pressure testing program progresses, personnel assigned to the program and outside observers and reviewers will be asked for comments regarding the testing procedures. New and/or improved test procedures will be documented as amendments to this test plan, and subject to similar review procedures

Simulations of the pipe overpack to compute constitutive model parameters for use in WIPP room closure calculations

International Nuclear Information System (INIS)

Park, Byoung Yoon; Hansen, Francis D.

2004-01-01

The regulatory compliance determination for the Waste Isolation Pilot Plant includes the consideration of room closure. Elements of the geomechanical processes include salt creep, gas generation and mechanical deformation of the waste residing in the rooms. The WIPP was certified as complying with regulatory requirements based in part on the implementation of room closure and material models for the waste. Since the WIPP began receiving waste in 1999, waste packages have been identified that are appreciably more robust than the 55-gallon drums characterized for the initial calculations. The pipe overpack comprises one such waste package. This report develops material model parameters for the pipe overpack containers by using axisymmetrical finite element models. Known material properties and structural dimensions allow well constrained models to be completed for uniaxial, triaxial, and hydrostatic compression of the pipe overpack waste package. These analyses show that the pipe overpack waste package is far more rigid than the originally certified drum. The model parameters developed in this report are used subsequently to evaluate the implications to performance assessment calculations

Environmental Impact Statement: Waste Isolation Pilot Plant (WIPP): Executive summary

International Nuclear Information System (INIS)

1980-10-01

The purpose of this document is to provide a summary of the environmental impact statement for the Waste Isolation Pilot Plant (WIPP) project. The Draft Environmental Impact Statement for the WIPP was published by the US Department of Energy (DOE) in April 1979. This document was reviewed and commented on by members of the general public, private organizations, and governmental agencies. The Final Environmental Impact Statement was subsequently published in October, 1980. This summary is designed to assist decision-maker and interested individuals in reviewing the material presented in the environmental impact statement for the WIPP project. To make this material widely available, this summary is published in both Spanish and English. Additional, more detailed information concerning the environmental and safety consequences of the WIPP project is available in the Final Environmental Impact Statement. Written comments and public hearing comments on the Draft Environmental Impact Statement are available for review. 27 refs., 4 figs., 7 tabs

WIPP [Waste Isolation Pilot Plant] test phase plan: Performance assessment

International Nuclear Information System (INIS)

1990-04-01

The U.S. Department of Energy (DOE) is responsible for managing the disposition of transuranic (TRU) wastes resulting from nuclear weapons production activities of the United States. These wastes are currently stored nationwide at several of the DOE's waste generating/storage sites. The goal is to eliminate interim waste storage and achieve environmentally and institutionally acceptable permanent disposal of these TRU wastes. The Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico is being considered as a disposal facility for these TRU wastes. This document describes the first of the following two major programs planned for the Test Phase of WIPP: Performance Assessment -- determination of the long-term performance of the WIPP disposal system in accordance with the requirements of the EPA Standard; and Operations Demonstration -- evaluation of the safety and effectiveness of the DOE TRU waste management system's ability to emplace design throughput quantities of TRU waste in the WIPP underground facility. 120 refs., 19 figs., 8 tabs

Hydrologic analyses of two brine encounters in the vicinity of the Waste Isolation Pilot Plant (WIPP) Site

International Nuclear Information System (INIS)

Spiegler, P.

1982-12-01

The data from ERDA-6 indicates a naturally fractured reservoir of the two-porosity type. The best estimate of the volume is about 60 thousand to 120 thousand barrels. The data from WIPP-12 also indicates a naturally fractured reservoir of the two-porosity type. The best estimate of the volume is about 5 million to 10 million barrels. The excess pressure above hydrostatic pressure suggests that the reservoirs were formed many millions of years ago. The location of the fractures suggest that their formation may be connected to the tilting of the Delaware Basin as a unit. The effect of the flow testing data on a drilling scenario through the repository many years following its closure is evaluated

A review of in situ investigations in salt

International Nuclear Information System (INIS)

Kuehn, K.

1985-01-01

In situ investigations for the disposal of radioactive wastes in rock salt formations have the longest history in the field. Well known names are Project Salt Vault (PSV) which was performed in the Lyons Mine, Kansas/USA, and the Asse salt mine in Germany. The overall objective for in situ investigations is twofold: 1. To produce all necessary data for the construction and operation of repositories and 2. to produce all necessary data for a performance assessment for repositories

DOE responses to the State of New Mexico's comments on ''summary of the results of the evaluation of the WIPP site and preliminary design validation program'' (WIPP-DOE-161)

International Nuclear Information System (INIS)

1983-06-01

During the 60-day period provided for comments on the ''Summary of the Results of the Evaluation of the WIPP Site and Preliminary Design Validation Program'' (WIPP-DOE-161), written submittals and hearing testimony from about 133 individuals, 7 citizens groups and 6 state agencies were received by the Department of Energy (DOE). Approximately 25% of the public comment submittals were positive statements supporting the WIPP, with the remaining 75% reflecting concern with one or more aspects of the project. A portion of the state's comment package (submitted by the Governor of New Mexico) contained concerns relevant to WIPP which were unrelated to site suitability. Supportive comments formed the majority of the submittals from the New Mexico Environmental Evaluation Group (EEG) which ''...is charged with the responsibility of evaluating the suitability of the site for carrying out the mission of WIPP by analyzing all the reports and other information which form the background to the DOE evaluation of the site''

Evolution of patterns of regional groundwater flow in southeastern New Mexico: Response to post-Pleistocene changes in climate

International Nuclear Information System (INIS)

Corbet, T.F.

1994-01-01

The Waste Isolation Pilot Plant (WIPP) is a potential repository for transuranic wastes generated by defense programs of the US Department of Energy. The repository site is located 42 km east of the city of Carlsbad, New Mexico in a thick, Permian-age deposit of bedded salt. One consideration in evaluating the performance of the repository is that a future society might inadvertently penetrate the repository with one or more drill holes. Given certain circumstances, these holes could provide a pathway for contaminated brine to move upward into relatively permeable strata located above the bedded salt. There is concern that flowing groundwater could then transport radionuclides laterally to the sub-surface portion of the accessible environment, currently defined by the disposal regulations as the region more than 5 kilometers from the radioactive waste. The simulations presented here are part of a numerical modeling study of the possible impact that a change in climate over the next 10,000 years could have on the pattern of groundwater flow and, consequently, on the migration of radionuclides in strata overlying the repository

Origin of the brines near WIPP from the drill holes ERDA-6 and WIPP-12 based on stable isotope concentrations of hydrogen and oxygen

International Nuclear Information System (INIS)

Spiegler, P.; Updegraff, D.

1983-03-01

Pathways which might alter the isotopic compositions of deuterium and oxygen-18 meteoric water, seawaters, and in hydration waters in gypsum to the isotopic compositions of brines encountered at ERDA-6 and WIPP-12 are discussed. Present geologic conditions do not favor the alteration of the isotopic compositions of waters that exist near the WIPP site to those of the brines by these pathways. It is concluded that the brines encountered at ERDA-6 and WIPP-12 are probably derived from ancient ocean waters that have been isotopically enriched in oxygen-18 by exchange interaction with rock. The dehydration of gypsum as a process of origin of these brines cannot be ruled out

Optimized application of systems engineering to nuclear waste repository projects

International Nuclear Information System (INIS)

Miskimin, P.A.; Shepard, M.

1986-01-01

The purpose of this presentation is to describe a fully optimized application of systems engineering methods and philosophy to the management of a large nuclear waste repository project. Knowledge gained from actual experience with the use of the systems approach on two repository projects is incorporated in the material presented. The projects are currently evaluating the isolation performance of different geologic settings and are in different phases of maturity. Systems engineering methods were applied by the principal author at the Waste Isolation Pilot Plant (WIPP) in the form of a functional analysis. At the Basalt Waste Isolation Project (BWIP), the authors assisted the intergrating contractor with the development and application of systems engineering methods. Based on this experience and that acquired from other waste management projects, an optimized plan for applying systems engineering techniques was developed. The plan encompasses the following aspects: project organization, developing and defining requirements, assigning work responsibilities, evaluating system performance, quality assurance, controlling changes, enhancing licensability, optimizing project performance, and addressing regulatory issues. This information is presented in the form of a roadmap for the practical application of system engineering principles to a nuclear waste repository project

Experiments and Modeling to Support Field Test Design

Energy Technology Data Exchange (ETDEWEB)

Johnson, Peter Jacob [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Bourret, Suzanne Michelle [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Zyvoloski, George Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boukhalfa, Hakim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stauffer, Philip H. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Weaver, Douglas James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-09-25

Disposition of heat-generating nuclear waste (HGNW) remains a continuing technical and sociopolitical challenge. We define HGNW as the combination of both heat generating defense high level waste (DHLW) and civilian spent nuclear fuel (SNF). Numerous concepts for HGNW management have been proposed and examined internationally, including an extensive focus on geologic disposal (c.f. Brunnengräber et al., 2013). One type of proposed geologic material is salt, so chosen because of its viscoplastic deformation that causes self-repair of damage or deformation induced in the salt by waste emplacement activities (Hansen and Leigh, 2011). Salt as a repository material has been tested at several sites around the world, notably the Morsleben facility in Germany (c.f. Fahland and Heusermann, 2013; Wollrath et al., 2014; Fahland et al., 2015) and at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, NM. Evaluating the technical feasibility of a HGNW repository in salt is an ongoing process involving experiments and numerical modeling of many processes at many facilities.

Comments on US approach to backfilling: Thermochemical characterization of crushed salt

International Nuclear Information System (INIS)

Smith, S.; Hume, H.

1988-01-01

From recent studies and calculations, it has become apparent that expected brine in a United States salt repository would not seriously detract from the usefulness of rock salt as backfill. It also has been shown that adding clay to the salt might add to the pressure on the emplaced waste packages. Nevertheless, the Salt Repository Project has planned to evaluate a betonite/salt mixture during the next few years. The following items have also been discussed: advantages of backfilling, variables affecting crushed salt behavior, and the general approach to a preliminary testing program

Pretest parametric calculations for the heated pillar experiment in the WIPP In-Situ Experimental Area

International Nuclear Information System (INIS)

Branstetter, L.J.

1983-03-01

Results are presented for a pretest parametric study of several configurations and heat loads for the heated pillar experiment (Room H) in the Waste Isolation Pilot Plant (WIPP) In Situ Experimental Area. The purpose of this study is to serve as a basis for selection of a final experiment geometry and heat load. The experiment consists of a pillar of undisturbed rock salt surrounded by an excavated annular room. The pillar surface is covered by a blanket heat source which is externally insulated. A total of five thermal and ten structural calculations are described in a four to five year experimental time frame. Results are presented which include relevant temperature-time histories, deformations, rock salt stress component and effective stress profiles, and maximum stresses in anhydrite layers which are in close proximity to the room. Also included are predicted contours of a conservative post-processed measure of potential salt failure. Observed displacement histories are seen to be highly dependent on pillar and room height, but insensitive to other geometrical variations. The use of a tensile cutoff across slidelines is seen to produce more accurate predictions of anhydrite maximum stress, but to have little effect on rock salt stresses. The potential for salt failure is seen to be small in each case for the time frame of interest, and is only seen at longer times in the center of the room floor

Chemical modeling of nuclear waste repositories in the salt repository project

International Nuclear Information System (INIS)

Jansen, G.; Raines, G.E.; Kircher, J.F.; Hubbard, N.

1985-01-01

Salt deposits contain small amounts of water as brine in fluid inclusions in halite and in hydrous minerals, e.g., clays, kieserite (MgSO 4 . H 2 O) and carnallite (KMgCl 3 . 6H 2 O). For the candidate salt deposits, the total amounts of water as volume % brine are: Palo Duro Basin, Texas, approximately 1.8; Paradox Basin, Utah, approximately 5.0 for the carnallite-marker zone, and less than approximately 0.5 below this zone; Gulf Coast salt domes, less than 0.15. For the Palo Duro and Paradox salt, the brines are Mg-rich (approximately 20,000 mg/L to approximately 100,000 mg/L) and sometimes Ca-rich (up to about 20,000 mg/L) NaCl brines. Brine migration calculations have been made using calculations of the time-variant thermal gradient around the waste packages and conservatively high brine volumes in the salt (5.0 volume % for the Texas and Utah sites and 0.5 volume % for the Gulf Coast) as input data. The maximum amounts of brine that eventually migrate to each waste package are about 1.0m 3 (for 5.0 volume % brine) and 0.2m 3 (for 0.5 volume % brine). With current conceptual designs for waste package overpacks (10 to 15 cm thick low-carbon steel), the waste package is not breached by uniform corrosion within 10,000 years. In brines this material thus far shows only uniform corrosion. For the expected conditions, where the brine is provided solely by brine migration, the brine is consumed by reaction with the iron of the overpack nearly as fast as it migrates to the waste package. Therefore, for the expected conditions, data about corrosion rates, radiolysis, etc., are not important. However, it is essential that accurate volumes of in-migrating brine can be calculated

Salt Repository Project site study plan for stratigraphic boreholes: Revision 1, December 18, 1987

International Nuclear Information System (INIS)

1987-01-01

This site study describes the Stratigraphic Boreholes field work to be conducted during the early stages of Site Characterization at the Deaf Smith County, Texas site. The field program has been designed to provide data useful in addressing information/data needs resulting from Federal/State/local regulations, and repository program requirements. Four Stratigraphic Holes will be drilled near the perimeter of the site to document the subsurface geologic conditions in that area and to provide data necessary for design and construction of the Exploratory Shaft Facilities. Continuous samples will be recovered from the ground surface to the total depth of each sell. Geophysical well logs will provide additional coverage of the stratigraphic section. In-situ down hole testing will include short term hydrologic tests and hydraulic fracture tests to provide information on deep groundwater characteristics and regional stress patterns, respectively. Field methods/tests are chosen that provide the best or only means of obtaining the required data. The Salt Repository Project (SRP) Networks specify the schedule which the program will operate. The Technical Services Contractor is responsible for conducting the field program of drilling and testing. Samples and data will be handled and reported in accordance with established SRP procedures. A quality assurance program will be utilized to assure that activities affecting quality are performed correctly and that the appropriate documentation is maintained. 30 refs., 13 figs., 4 tabs

Site study plan for Playa investigations, Deaf Smith County, Texas: Salt Repository Project

International Nuclear Information System (INIS)

1987-01-01

This plan defines the purpose and objectives of the Playa Investigation Study, presents a plan of work to provide the information necessary to resolve issues, and discusses the rationale for test method selection. The required information will be obtained from existing well drilling records, describing and testing of soil and rock samples recovered from project test holes, geophysical well logs, seismic surveys, and shallow test pits excavated at ground surface. There have been numerous, often conflicting, theories presented to explain the origin(s) of the playas of the Texas High Plains. The primary purpose of this study is to establish if existing playas and playa alignments are related to deeper subsurface structure, such as faulting or salt dissolution, the potential for future playa development, and the significance of existing and/or future playas on siting a repository in Deaf Smith County, Texas. 11 refs

Waste Isolation Pilot Plant in situ experimental program for HLW

International Nuclear Information System (INIS)

Molecke, M.A.

1977-01-01

The Waste Isolation Pilot Plant (WIPP) will be a facility to demonstrate the environmental and operational safety of storing radioactive wastes in a deep geologic bedded salt facility. The WIPP will be located in southeastern New Mexico, approximately 30 miles east of the city of Carlsbad. The major focus of the pilot plant operation involves ERDA defense related low and intermediate-level transuranic wastes. The scope of the project also specifically includes experimentation utilizing commercially generated high-level wastes, or alternatively, spent unreprocessed fuel elements. WIPP HLW experiments are being conducted in an inter-related laboratory, bench-scale, and in situ mode. This presentation focuses on the planned in situ experiments which, depending on the availability of commercially reprocessed waste plus delays in the construction schedule of the WIPP, will begin in approximately 1985. Such experiments are necessary to validate preceding laboratory results and to provide actual, total conditions of geologic storage which cannot be adequately simulated. One set of planned experiments involves emplacing bare HLW fragments into direct contact with the bedded salt environment. A second set utilizes full-size canisters of waste emplaced in the salt in the same manner as planned for a future HLW repository. The bare waste experiments will study in an accelerated manner waste-salt bed-brine interactions including matrix integrity/degradation, brine leaching, system chemistry, and potential radionuclide migration through the salt bed. Utilization of full-size canisters of HLW in situ permits us to demonstrate operational effectiveness and safety. Experiments will evaluate corrosion and compatibility interactions between the waste matrix, canister and overpack materials, getter materials, stored energy, waste buoyancy, etc. Using full size canisters also allows us to demonstrate engineered retrievability of wastes, if necessary, at the end of experimentation