Statistical methods for mechanistic model validation: Salt Repository Project

International Nuclear Information System (INIS)

Eggett, D.L.

1988-07-01

As part of the Department of Energy's Salt Repository Program, Pacific Northwest Laboratory (PNL) is studying the emplacement of nuclear waste containers in a salt repository. One objective of the SRP program is to develop an overall waste package component model which adequately describes such phenomena as container corrosion, waste form leaching, spent fuel degradation, etc., which are possible in the salt repository environment. The form of this model will be proposed, based on scientific principles and relevant salt repository conditions with supporting data. The model will be used to predict the future characteristics of the near field environment. This involves several different submodels such as the amount of time it takes a brine solution to contact a canister in the repository, how long it takes a canister to corrode and expose its contents to the brine, the leach rate of the contents of the canister, etc. These submodels are often tested in a laboratory and should be statistically validated (in this context, validate means to demonstrate that the model adequately describes the data) before they can be incorporated into the waste package component model. This report describes statistical methods for validating these models. 13 refs., 1 fig., 3 tabs

Salt repository design approach

International Nuclear Information System (INIS)

Matthews, S.C.

1983-01-01

This paper presents a summary discussion of the approaches that have been and will be taken in design of repository facilities for use with disposal of radioactive wastes in salt formations. Since specific sites have yet to be identified, the discussion is at a general level, supplemented with illustrative examples where appropriate. 5 references, 1 figure

Assessment of crushed salt consolidation and fracture healing processes in a nuclear waste repository in salt

International Nuclear Information System (INIS)

1984-11-01

For a nuclear waste repository in salt, two aspects of salt behavior are expected to contribute to favorable conditions for waste isolation. First, consolidation of crushed salt backfill due to creep closure of the underground openings may result in a backfill barrier with low permeability. Second, fractures created in the salt by excavation may heal under the influence of stress and temperature following sealing. This report reviews the status of knowledge regarding crushed salt consolidation and fracture healing, provides analyses which predict the rates at which the processes will occur under repository conditions, and develops requirements for future study. Analyses of the rate at which crushed salt will consolidate are found to be uncertain because of unexplained wide variation in the creep properties of crushed salt obtained from laboratory testing, and because of uncertainties in predictions of long term closure rates of openings in salt. This uncertainty could be resolved to a large degree by additional laboratory testing of crushed salt. Similarly, additional testing of fracture healing processes is required to confirm that healing will be effective under repository conditions. Extensive references, 27 figures, 5 tables

Salt Repository Project shaft design guide: Revision 0

International Nuclear Information System (INIS)

1987-12-01

The Salt Repository Project (SRP) Shaft Design Guide (SDG) and the accompanying SRP Input to Seismic Design define the basic approach for developing appropriate shaft designs for a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. The SDG is based on current mining industry standards and practices enhanced to meet the special needs of an underground nuclear waste repository. It provides a common approach for design of both the exploratory and repository shafts. The SDG defines shaft lining and material concepts and presents methods for calculating the loads and displacements that will be imposed on lining structures. It also presents the methodology and formulae for sizing lining components. The SDG directs the shaft designer to sources of geoscience and seismic design data for the Deaf Smith County, Texas repository site. In addition, the SDG describes methods for confirming shaft lining design by means of computer analysis, and it discusses performance monitoring needs that must be considered in the design. 113 refs., 18 figs., 14 tabs

Sealing considerations for repository shafts in bedded and dome salt

International Nuclear Information System (INIS)

1981-12-01

The report reviews the geologic and hydrologic data base for penetration seal designs referenced to the Los Medanos bedded salt site in New Mexico and to four candidate salt domes in the Gulf Interior. Experience with existing shafts highlights the importance, for shaft decommissioning as well as operation, of achieving an adequate seal at and immediately below the top of salt. Possible construction procedures for repository shafts are reviewed, noting advantages and disadvantages with respect to repository sealing. At this stage, there does not appear to be a clear preference for excavation by drill and blast or by drilling. If conventional drill and blast methods are used, it may be necessary to grout in permeable zones above the salt. An important consideration with respect to sealing is that grouting operations (or freezing should it be used) should not establish connections between the top of salt and water-bearing zones higher in the stratigraphic section. Generally, it is concluded that Los Medanos and the dome salt sites are favorable candidate repository sites from the point of view of sealing

Chemotoxic materials in a final repository for high-level radioactive wastes. CHEMOTOX concept for defence in depth concerning ground water protection from chemotoxic materials in a final high-level waste repository

International Nuclear Information System (INIS)

Alt, Stefan; Sailer, Michael; Schmidt, Gerhard; Herbert, Horst-Juergen; Krone, Juergen; Tholen, Marion

2009-01-01

The disposal of high-level radioactive wastes in a final repository includes chemotoxic materials. The chemotoxic materials are either part of the radioactive material or part of the packaging material, or the structures within the repository. In the frame of the licensing procedure it has to be demonstrated that no hazardous pollution of the ground water or other disadvantageous changes can occur. The report describes the common project of the Oeko-Institut e.V., the DBE Technology GmbH and the GRS mbH concerning the possible demonstration of a systematic protection of the groundwater against chemotoxic materials in case of a final high-level-radioactive waste repository in the host materials salt and clay stone.

Preliminary analyses of scenarios for potential human interference for repositories in three salt formations

International Nuclear Information System (INIS)

1985-10-01

Preliminary analyses of scenarios for human interference with the performance of a radioactive waste repository in a deep salt formation are presented. The following scenarios are analyzed: (1) the U-Tube Connection Scenario involving multiple connections between the repository and the overlying aquifer system; (2) the Single Borehole Intrusion Scenario involving penetration of the repository by an exploratory borehole that simultaneously connects the repository with overlying and underlying aquifers; and (3) the Pressure Release Scenario involving inflow of water to saturate any void space in the repository prior to creep closure with subsequent release under near lithostatic pressures following creep closure. The methodology to evaluate repository performance in these scenarios is described and this methodology is applied to reference systems in three candidate formations: bedded salt in the Palo Duro Basin, Texas; bedded salt in the Paradox Basin, Utah; and the Richton Salt Dome, Mississippi, of the Gulf Coast Salt Dome Basin

Status of the safety concept and safety demonstration for an HLW repository in salt. Summary report

Energy Technology Data Exchange (ETDEWEB)

Bollingerfehr, W.; Buhmann, D.; Filbert, W.; and others

2013-12-15

safety demonstration are the integrity proofs for the geological and geotechnical barriers and analysis of backfill compaction. In addition, any possible radionuclide release from the repository to the environment has also to be assessed. The safety and demonstration concept developed in the course of the ISIBEL project was further evolved and applied in the course of the R and D project ''Vorlaeufige Sicherheitsanalyse Gorleben - VSG'' (preliminary safety analysis Gorleben) as an example for an HLW repository in a domal salt structure. The repository concepts also consider the requirement for retrievability of stored waste during the operational phase of the repository. The results of the R and D project VSG provide evidence that a safe HLW repository within a salt dome of a suitable geologic structure is feasible. The long-term safety can be ensured using state-of-the-art science and technology. In 2010, the Federal Ministry for the Environment, Nature Conservation and Nuclear Safety (BMU) issued new safety requirements for the disposal of heat-generating radioactive waste. These requirements have been included in the analysis. This study shows the depth of the geological and technical knowledge on final disposal of HLW in a salt dome with a suitable geologic structure and demonstrates that the tools required for safety evaluations are available and allow reliable safety assessments of HLW repositories in salt formations.

Inelastic thermomechanical analysis of a generic bedded salt repository. Technical report

International Nuclear Information System (INIS)

Callahan, G.D.

1981-02-01

The thermomechanical response of a generic bedded salt stratigraphy accommodating a spent fuel repository at a depth of 610 m in a relatively thin salt bed is investigated. The thermal density at waste emplacement was assumed to be 14.8 W/m 2 (60 kW/acre). Emphasis is placed on rock mass properties, elastic and thermal anisotropy (within the shale layers), and structural discontinuities defined as preferred planes of weakness. No attempt is made to include long-term effects of geologic actions, chemical processes, groundwater, and pore water. The rock mass is assumed to contain pre-existing joints and fissures. Therefore, the stratigraphy encompassing the repository (excluding the salt beds) was assumed to be incapable of supporting tensile stresses. Thermoelastic/plastic response of the various sedimentary formations is considered for the intact rock mass and several orientations of preferred planes of weakness. The results indicate an intact buffer zone between the upper strata and the repository approximately 450 m thick, which underwent no irreversible deformation. Contained plastic deformation was observed below the repository along preferred planes of weakness dipping at 60 and 120 degrees. The structural response of this generic bedded salt stratigraphy does not appear to be detrimental to the overall waste containment in the repository

Experimental results on salt concrete for barrier elements made of salt concrete in a repository for radioactive waste in a salt mine

International Nuclear Information System (INIS)

Gutsch, Alex-W.; Preuss, Juergen; Mauke, Ralf

2012-01-01

The Bartensleben rock salt mine in Germany was used as a repository for low and intermediate level radioactive waste from 1971 to 1991 and from 1994 to 1998. The repository with an overall volume of about 6 million m 3 has to be closed. Salt concrete is used for the refill of the voids of the repository. The concrete mixtures contain crushed salt instead of natural aggregates as the void filling material should be as similar to the salt rock as possible. Very high requirements regarding low heat development and little or even no cracking during concrete hardening had to be fulfilled even for the barrier elements made from salt concrete which separate the radioactive waste from the environment. Requirements for the salt concrete were set up with regard to the fluidity of the fresh concrete during the hardening process and its durability. In the view of a comprehensive numerical calculations of the temperature development and thermal stresses in the massive salt concrete elements of the backfill of the voids, experimental results for material properties of the salt concrete are presented: mixture of the salt concrete, thermodynamic properties (adiabatic heat release, thermal dilatation, thermal conductivity and heat capacity), mechanical short term properties, creep (under tension, under compression), autogenous shrinkage

Salt Repository Project transportation program plan

International Nuclear Information System (INIS)

Fisher, R.L.; Greenberg, A.H.; Anderson, T.L.; Yates, K.R.

1987-01-01

The Salt Repository Project (SRP) has the responsibility to develop a comprehensive transportation program plan (TrPP) that treats the transportation of workers, supplies, and high-level radioactive waste to the site and the transportation of salt, low-level, and transuranic wastes from the site. The TrPP has developed a systematic approach to transportation which is directed towards satisfying statutes, regulations, and directives and is guided by a hierarchy of specific functional requirements, strategies, plans, and reports. The TrPP identifies and develops the planning process for transportation-related studies and provides guidance to staff in performing and documenting these activities. The TrPP also includes an explanation of the responsibilities of the organizational elements involved in these transportation studies. Several of the report chapters relate to identifying routes for transporting nuclear waste to the site. These include a chapter on identifying an access corridor for a new rail route leading to the site, identifying and evaluating emergency-response preparedness capabilities along candidate routes in the state, and identifying alternative routes from the state border, ports, or in-state reactors to the site. The TrPP also includes plans for identifying salt disposal routes and a discussion of repository/transportation interface requirements. 89 refs., 6 figs

Performance assessment plans and methods for the Salt Repository Project

International Nuclear Information System (INIS)

1984-08-01

This document presents the preliminary plans and anticipated methods of the Salt Repository Project (SRP) for assessing the postclosure and radiological aspects of preclosure performance of a nuclear waste repository in salt. This plan is intended to be revised on an annual basis. The emphasis in this preliminary effort is on the method of conceptually dividing the system into three subsystems (the very near field, the near field, and the far field) and applying models to analyze the behavior of each subsystem and its individual components. The next revision will contain more detailed plans being developed as part of Site Characterization Plan (SCP) activities. After a brief system description, this plan presents the performance targets which have been established for nuclear waste repositories by regulatory agencies (Chapter 3). The SRP approach to modeling, including sensitivity and uncertainty techniques is then presented (Chapter 4). This is followed by a discussion of scenario analysis (Chapter 5), a presentation of preliminary data needs as anticipated by the SRP (Chapter 6), and a presentation of the SRP approach to postclosure assessment of the very near field, the near field, and the far field (Chapters 7, 8, and 9, respectively). Preclosure radiological assessment is discussed in Chapter 10. Chapter 11 presents the SRP approach to code verification and validation. Finally, the Appendix lists all computer codes anticipated for use in performance assessments. The list of codes will be updated as plans are revised

Repository seal materials performance for a SALT Repository Project 5-year code/model development plan: Draft

International Nuclear Information System (INIS)

1987-06-01

This document describes an integrated laboratory testing and model development effort for the seal system for a high-level nuclear waste repository in salt. The testing and modeling efforts are designed to determine seal material response in the repository environment, to provide models of seal system components for performance assessment, and to assist in the development of seal system designs. A code/model development and performance analysis program will be performed to predict the short- and long-term response of seal materials and seal components. The results from these analyses will be used to support the material testing activities on this contract and to support performance assessment activities that are conducted in other parts of the Salt Repository Project (SRP). 48 refs., 15 figs., 4 tabs

ERG [Engineering Review Group] review of the SRP [Salt Repository Project] salt irradiation effects program: Technical report

International Nuclear Information System (INIS)

Clark, D.E.

1986-11-01

The Engineering Review Group (ERG) was established by the Office of Nuclear Waste Isolation (ONWI) to help evaluate engineering-related issues in the US Department of Energy's nuclear waste repository program. The August 1985 meeting of the ERG reviewed the Salt Repository Project (SRP) salt irradiation effects program. This report documents the ERG's comments and recommendations on these subjects and the ONWI response to the specific points raised by the ERG

Microbial Influence on the Performance of Subsurface, Salt-Based Radioactive Waste Repositories. An Evaluation Based on Microbial Ecology, Bioenergetics and Projected Repository Conditions

International Nuclear Information System (INIS)

Swanson, J.S.; Reed, D.T.; Cherkouk, A.; Arnold, T.; Meleshyn, A.; Patterson, Russ

2018-01-01

For the past several decades, the Nuclear Energy Agency Salt Club has been supporting and overseeing the characterisation of rock salt as a potential host rock for deep geological repositories. This extensive evaluation of deep geological settings is aimed at determining - through a multidisciplinary approach - whether specific sites are suitable for radioactive waste disposal. Studying the microbiology of granite, basalt, tuff, and clay formations in both Europe and the United States has been an important part of this investigation, and much has been learnt about the potential influence of microorganisms on repository performance, as well as about deep subsurface microbiology in general. Some uncertainty remains, however, around the effects of microorganisms on salt-based repository performance. Using available information on the microbial ecology of hyper-saline environments, the bioenergetics of survival under high ionic strength conditions and studies related to repository microbiology, this report summarises the potential role of microorganisms in salt-based radioactive waste repositories

Corrosion behavior of spent MTR fuel elements in a drowned salt mine repository

International Nuclear Information System (INIS)

Brodda, B.G.; Fachinger, J.

1995-01-01

Spent MTR fuel from German Material Test Reactors will not be reprocessed, but stored in a final salt repository in the deep geologic underground. Fuel elements will be placed in POLLUX containers, which are assumed to resist the corrosive attack of an accidentally formed concentrated salt brine for about 500 years. After a container failure the brine would contact the fuel element, corrode the aluminum plating and possibly leach radionuclides from the fuel. A source term for the calculation of radionuclide mobilization results from the investigation of the behavior of MTR fuel in this scenario, which has to be considered for the long-term safety analysis of a deep mined rock salt repository. Experiments with the different plating materials show that the considered aluminum alloys will not resist the corrosive attack of a brine solution, especially in the presence of iron, under the conditions in a drowned salt mine repository. Although differences in the corrosion rates of about two orders of magnitude were observed when applying different parameter sets, the deterioration must be considered to be almost instantaneous in geological terms. Radionuclides are mobilized from irradiated MTR fuel, when the meat of the fuel element becomes accessible to the brine solution. It seems, however, that the radionuclides are effectively trapped by the aluminum hydroxide formed, as the activity concentrations in the brine solution soon reach a constant level with the progressing corrosion of the cladding aluminum. In the presence of iron a more significant initial release was observed, but also in this case an equilibrium activity seems to be reached as a consequence of radionuclide trapping

Release consequence analysis for a hypothetical geologic radioactive waste repository in salt

International Nuclear Information System (INIS)

1979-08-01

One subtask conducted under the INFCE program is to evaluate and compare the health and safety impacts of different fuel cycles in which all radioactive wastes (except those from mining and milling) are placed in a geologic repository in salt. To achieve this objective, INFCE Working Group 7 examined the radiologic dose to humans from geologic repositories containing waste arisings as defined for seven reference fuel cycles. This report examines the release consequences for a generic waste repository in bedded salt. The top of the salt formation and the top of the repository are assumed to be 250 and 600 m, respectively, below the surface. The hydrogeologic structure above the salt consists of two aquifers and two aquitards. The aquifers connect to a river 6.2 km from the repository. The regional gradient to the river is 1 m/km in all aquifers. Hydrologic, transport, and dose models were used to model two release scenarios for each fuel cycle, one without a major disturbance and one in which a major geologic perturbation breached the repository immediately after it was sealed. The purpose of the modeling was to predict the rate of transport of radioactive contaminants from the repository through the geosphere to the biosphere, and to determine the potential dose to humans. Of the many radionuclides in the waste, only 129 I and 226 Ra arrived at the river in sufficient concentrations for a measurable dose calculation. Radionuclide concentrations in the ground water pose no threat to man because the ground water is a concentrated brine and it is diluted by a factor of 10 6 to 10 7 upon entering the river

Expected brine movement at potential nuclear waste repository salt sites

International Nuclear Information System (INIS)

McCauley, V.S.; Raines, G.E.

1987-08-01

The BRINEMIG brine migration code predicts rates and quantities of brine migration to a waste package emplaced in a high-level nuclear waste repository in salt. The BRINEMIG code is an explicit time-marching finite-difference code that solves a mass balance equation and uses the Jenks equation to predict velocities of brine migration. Predictions were made for the seven potentially acceptable salt sites under consideration as locations for the first US high-level nuclear waste repository. Predicted total quantities of accumulated brine were on the order of 1 m 3 brine per waste package or less. Less brine accumulation is expected at domal salt sites because of the lower initial moisture contents relative to bedded salt sites. Less total accumulation of brine is predicted for spent fuel than for commercial high-level waste because of the lower temperatures generated by spent fuel. 11 refs., 36 figs., 29 tabs

Shaft placement in a bedded salt repository

International Nuclear Information System (INIS)

Klasi, M.L.

1982-10-01

Preferred shaft pillar sizes and shaft locations were determined with respect to the induced thermal stresses in a generic bedded salt repository at a depth of 610 m with a gross thermal loading of 14.8 W/m 2 . The model assumes isotropic material properties, plane strain and linear elastic behavior. Various shaft locations were analyzed over a 25 year period. The thermal results show that for this time span, the stratigraphy is unimportant except for the region immediately adjacent to the repository. The thermomechanical results show that for the given repository depth of 610 m, a minimum central shaft pillar radius of 244 m is required to equal the material strength in the barrier pillar. An assumed constant stress and constant temperature distribution creep model of the central shaft region adjacent to the repository conservatively overestimates a creep closure of 310 mm in a 6.1 m diameter centrally-located shaft

Salt Repository Project Waste Package Program Plan: Draft

International Nuclear Information System (INIS)

Carr, J.A.; Cunnane, J.C.

1986-01-01

Under the direction of the Office of Civilian Radioactive Waste Management (OCRWM) created within the DOE by direction of the Nuclear Waste Policy Act of 1982 (NWPA), the mission of the Salt Repository Project (SRP) is to provide for the development of a candidate salt repository for disposal of high-level radioactive waste (HLW) and spent reactor fuel in a manner that fully protects the health and safety of the public and the quality of the environment. In consideration of the program needs and requirements discussed above, the SRP has decided to develop and issue this SRP Waste Package Program Plan. This document is intended to outline how the SRP plans to develop the waste package design and to show, with reasonable assurance, that the developed design will satisfy applicable requirements/performance objectives. 44 refs., 16 figs., 16 tabs

Monitoring system specifications: retrieval of surf from a salt repository

International Nuclear Information System (INIS)

1980-01-01

The task of developing specifications for a reference monitoring system determined by repository environmental conditions, retrieval operations, and federal regulatory criteria is discussed. The monitoring system specified in this report is capable of measuring (1) package position and orientation, (2) vault deformation, (3) brine accumulation, (4) spent fuel dissolution, (5) temperature, (6) nuclear radiation, and (7) package condition with sufficient accuracy to provide data input to a general risk assessment model. In order to define a monitoring system which can provide probabilistic data on radiological risk to operating personnel and the general public for a salt mine repository, the following information is required: (1) a complete design of the salt SURF repository including inventory, density and waste package design details; (2) probalistic failure rate data on containment integrity of the SURF waste package; (3) probabilistic failure rate data on the monitoring system components

Definition of the waste package environment for a repository located in salt

International Nuclear Information System (INIS)

Clark, D.E.; Bradley, D.J.

1983-01-01

The expected environmental conditions for emplaced waste packages in a salt repository are simulated in the materials testing program to evaluate performance. Synthetic brines, based on the analyses of actual brines (both intrusion and inclusion), are used for corrosion and leach testing. Elevated temperatures (to 150 0 C) and radiation fields of up to 10 3 rad/h are employed as conservative conditions to bracket expected performance and provide data for worst case scenarios. Obtaining a precise definition of the waste package environment in a salt repository and its change with time is closely tied to detailed site characterization of the candidate salt repository horizon. It is expected that field testing can augment some of the materials testing currently under way and can provide increased confidence in the predicted site-specific near-field conditions. 17 references, 5 figures, 1 table

Geotechnical instrumentation for repository shafts

International Nuclear Information System (INIS)

Lentell, R.L.; Byrne, J.

1993-01-01

The US Congress passed the Nuclear Waste Policy Act in 1980, which required that three distinctly different geologic media be investigated as potential candidate sites for the permanent disposal of high-level nuclear waste. The three media that were selected for study were basalt (WA), salt (TX, LA, MS, UT), and tuff (NV). Preliminary Exploratory Shaft Facilities (ESF) designs were prepared for seven candidate salt sites, including bedded and domal salt environments. A bedded-salt site was selected in Deaf Smith County, TX for detailed site characterization studies and ESF Final Design. Although Congress terminated the Salt Repository Program in 1988, Final Design for the Deaf Smith ESF was completed, and much of the design rationale can be applied to subsequent deep repository shafts. This paper presents the rationale for the geotechnical instrumentation that was designed for construction and operational performance monitoring of the deep shafts of the in-situ test facility. The instrumentation design described herein can be used as a general framework in designing subsequent instrumentation programs for future high-level nuclear waste repository shafts

USGS studies of physical--chemical relationships in salt repositories

International Nuclear Information System (INIS)

Stewart, D.B.

1977-01-01

The amount and physical properties of brine that can occur in salt repositories at elevated temperatures and pressures adjacent to waste-bearing cannisters will have considerable impact on the mechanical strength and stability of the repository. Brine will form readily from H 2 O absorbed on surfaces, diffusion along grain boundaries, movement of fluid inclusions, dehydration of hydrous minerals such as gypsum, polyhalite or clays, or even from leakage through failed shaft openings. A T-P diagram for NaCl--H 2 O shows the limits for coexisting solid-liquid-gas assemblages in salt repositories. Isobaric T-X diagrams are included to show compositional details at pressures below the critical point and above it. Properties of the fluid phases such as volume, density, heat capacity, enthalpy, viscosity, surface tension, osmotic coefficients, etc. can be well described (>0.01% to 2 O. Because aggregates of solids are mechanically weakened by interstitial liquid, determination of mechanical properties of brine-bearing aggregates is needed. A maximum of one third by weight of brine (not H 2 O), and probably much less, will destroy rock strength

Expected environment for waste packages in a salt repository

International Nuclear Information System (INIS)

Pederson, L.R.; Clark, D.E.; Hodges, F.N.; McVay, G.L.; Rai, D.

1983-01-01

This paper discusses results of recent efforts to define the very near-field (within approximately 2 m) environmental conditions to which waste packages will be exposed in a salt repository. These conditions must be considered in the experimental design for waste package materials testing, which includes corrosion of barrier materials and leaching of waste forms. Site-specific brine compositions have been determined, and standard brine compositions have been selected for testing purposes. Actual brine compositions will vary depending on origin, temperature, irradiation history, and contact with irradiated rock salt. Results of irradiating rock salt, synthetic brines, rock salt/brine mixtures, and reactions of irradiated rock salt with brine solutions are reported. 38 references, 3 figures, 2 tables

The function of packing materials in a high-level nuclear waste repository and some candidate materials: Salt Repository Project

International Nuclear Information System (INIS)

Bunnell, L.R.; Shade, J.W.

1987-03-01

Packing materials should be included in waste package design for a high-level nuclear waste repository in salt. A packing material barrier would increase confidence in the waste package by alleviating possible shortcomings in the present design and prolonging confinement capabilities. Packing materials have been studied for uses in other geologic repositories; appropriately chosen, they would enhance the confinement capabilities of salt repository waste packages in several ways. Benefits of packing materials include retarding or chemically modifying brines to reduce corrosion of the waste package, providing good thermal conductivity between the waste package and host rock, retarding or absorbing radionuclides, and reducing the massiveness of the waste package. These benefits are available at low percentage of total repository cost, if the packing material is properly chosen and used. Several candidate materials are being considered, including oxides, hydroxides, silicates, cement-based mixtures, and clay mixtures. 18 refs

Systems engineering management plan for the Salt Repository Project

International Nuclear Information System (INIS)

Neff, J.O.

1986-08-01

This document presents the plan for using systems engineering in conducting and managing the technical work of the Salt Repository Project (SRP) of the US Department of Energy's Civilian Radioactive Waste Management Program. The need for preparing a Systems Engineering Management Plan (SEMP) is traced back to relevant DOE directives. These directives are interpreted as SRP requirements in the context of the Mined Geologic Disposal System. The strategy for conducting systems engineering on the SRP, including the role of the systems engineering process, is then described. The SEMP also designates who in the project organization will be responsible for carrying out the activities. Finally, the management tools that are used to implement the systems engineering process, including associated documentation on the SRP, are described

Offsite testing in support of the Salt Repository Project

International Nuclear Information System (INIS)

Kalia, H.N.

1987-04-01

This report presents a rationale and recommendation to perform an offsite testing program in support of the Salt Repository Project. The investigation to be performed primarily consists of qualifying test methods and procedures, qualifying personnel-training procedures, evaluating test instruments and selected equipment, and obtaining mining and production equipment performance-related information. The key objective of these activities is to develop capabilities to be used at the exploratory shaft facility (ESF). The ESF is to be excavated at the Deaf Smith County site to characterize the salt site for the construction of a repository used to isolate radioactive waste from the biosphere. The bulk of the offsite testing work will be performed at Avery Island Salt Mine at New Iberia, Lousiana. Additional knowledge will be obtained by exchanging technical information either as participants or as observers at the Waste Isolation Pilot Plant (WIPP) site and the Asse Mine in the Federal Republic of Germany (FRG). It is estimated that the offsite testing program will cost approximately $9.3 million over 4 fiscal years. 14 refs., 1 fig., 8 tabs

Emplacement and retrieval equipment design considerations for a repository in salt

International Nuclear Information System (INIS)

Nair, B.R.; Bahorich, R.J.

1987-01-01

The current design concept for the disposal of nuclear high level waste packages in a repository in salt is based on the emplacement of individual packages in vertical boreholes in the underground mine floor. A key requirement is that the waste packages be capable of being retrieved during the last 26 years of the 76-year repository operating period. The unique design considerations relating to the retrieval of waste packages emplaced in bedded salt are presented in this paper. The information is based on the experience developed during the design of vertical emplacement and retrieval equipment in support of the Sandia Defense High Level Waste experiments at the Waste Isolation Pilot Plant. Also included are the impact of retrievability on the design of the equipment, the special salt cutting technology that was developed for this application, and a description of the equipment

Compilation of data for thermomechanical analyses of four potential salt repositories

International Nuclear Information System (INIS)

Tammemagi, H.Y.; Loken, M.C.; Osnes, J.D.; Wagner, R.A.

1986-01-01

This report includes a collection and summarization of the data which are necessary to perform thermomechanical analyses of four potential salt repository sites: Paradox Basin, Utah; Permian Basin, Texas; Richton Dome, Mississippi; and Vacherie Dome, Louisiana. Thermal, mechanical, and hydrogeological material properties are presented so that the numerical analyses can be subdivided into three geometric regions: canister, disposal room, and repository site. Data are presented for the salt formations, the surrounding geological units, and for human-made materials placed in the repository such as the nuclear waste and its protective steel liner. Wherever possible, site-specific data are used which have been determined from laboratory testing of drill core or from interpretation of geophysical logs. Although much effort has been made to obtain the most appropriate data, there are deficiencies because some of the required site-specific data are either not available or are inconsistent with anticipated values

Waste package for a repository located in salt

International Nuclear Information System (INIS)

Basham, S.J. Jr.

1983-01-01

This paper describes the current status of the waste package designs for salt repositories. The status of the supporting studies of environment definition, corrosion of containment materials, and leaching of waste forms is also presented. Emphasis is on the results obtained in FY 83 and the planned effort in FY 84. 8 references, 3 figures, 1 table

Preliminary evaluation of solution-mining intrusion into a salt-dome repository

International Nuclear Information System (INIS)

1981-06-01

This report is the product of the work of an ONWI task force to evaluate inadvertant human intrusion into a salt dome repository by solution mining. It summarizes the work in the following areas: a general review of the levels of defense that could reduce both the likelihood and potential consequences of human intrusion into a salt dome repository; evaluation of a hypothetical intrusion scenario and its consequences; recommendation for further studies. The conclusions of this task force report can be summarized as follows: (1) it is not possible at present to establish with certainty that solution mining is credible as a human-intrusion event. The likelihood of such an intrusion will depend on the effectiveness of the preventive measures; (2) an example analysis based on the realistic approach is presented in this report; it concluded that the radiological consequences are strongly dependent upon the mode of radionuclide release from the waste form, time after emplacement, package design, impurities in the host salt, the amount of a repository intercepted, the solution mining cavity form, the length of time over which solution mining occurs, the proportion of contaminated salt source for human consumption compared to other sources, and the method of salt purification for culinary purposes; (3) worst case scenarios done by other studies suggest considerable potential for exposures to man while preliminary evaluations of more realistic cases suggest significantly reduced potential consequences. Mathematical model applications to process systems, guided by more advanced assumptions about human intrusion into geomedia, will shed more light on the potential for concerns and the degree to which mitigative measures will be required

Comparison of risks due to HLW and SURF repositories in bedded salt

International Nuclear Information System (INIS)

Chu, M.S.Y.; Ortiz, N.R.; Wahi, K.K.

1983-01-01

A methodology was developed for use in the analysis of risks from geologic disposal of nuclear wastes. This methodology is applied to two conceptual nuclear waste repositories in bedded salt containing High-Level Waste (HLW) and Spent Un-Reprocessed Fuel (SURF), respectively. A comparison of the risk estimated from the HLW and SURF repositories is presented

Further design work on a repository in a salt dome

International Nuclear Information System (INIS)

Hamstra, J.; Janssen, L.G.L.

1985-01-01

The report presents the cost estimate and the work plan for the construction of a repository, to be mined in a medium-size salt dome for the simultaneous disposal of different categories of solid radioactive wastes. The repository is designed for all categories of waste from 40 years of operation of 25 nuclear power stations of 1000 MWe each, including the decommissioning waste from these stations as well as all the radioactive wastes from the hospitals and laboratories during a hundred-year period. The cost estimate includes preparation of a site, the construction, operation and abandonment of that repository. Moreover, an outline has been presented for a future updating and optimization study of the concept

Radiological consequences associated with human intrusion into radioactive waste repositories in salt formations

International Nuclear Information System (INIS)

Jacquier, P.

1989-01-01

The assessment of the radiological impact of human intrusion scenarios is extremely important in the case of repositories located in salt formations, since salt is obviously a valuable economic resource. Salt formations also represent a suitable medium for mining storage caverns for oil and gas. The scenario considered in this report is that of solution mining in salt formations to produce salt for human consumption. It is postulated that the salt is extracted by excavating a cavern through solution-mining and that, in the course of cavern enlargement, the waste is intercepted and drops to the bottom of the cavern. We have assumed that the intrusion takes place 500 or even 2 500 years after the repository has been sealed. The cases considered involve high-level vitrified waste or cemented alpha waste. The paper describes the assumptions on which the scenario is based and uses a simplified model to assess the radiological consequences associated with the ingestion of contaminated salt. The paper also provides details of a sensitivity/uncertainty analysis which identified several areas in which experimental studies should be either initiated or continued [fr

Analysis of the geological stability of a hypothetical radioactive waste repository in a bedded salt formation

International Nuclear Information System (INIS)

Tierney, M.S.; Lusso, F.; Shaw, H.R.

1978-01-01

This document reports on the development of mathematical models used in preliminary studies of the long-term safety of radioactive wastes deeply buried in bedded salt formations. Two analytical approaches to estimating the geological stability of a waste repository in bedded salt are described: (a) use of probabilistic models to estimate the a priori likelihoods of release of radionuclides from the repository through certain idealized natural and anthropogenic causes, and (b) a numerical simulation of certain feedback effects of emplacement of waste materials upon ground-water access to the repository's host rocks. These models are applied to an idealized waste repository for the sake of illustration

Planned investigations for packing materials for a waste package in a salt repository: [Final report

International Nuclear Information System (INIS)

Shade, J.W.; Bunnell, L.R.; Thornton, T.A.

1987-10-01

A considerable number of materials have been either proposed or investigated as packing materials for nuclear waste package systems. Almost always the expandable clays, such as the smectites contained in commercial bentonites, have received the most attention when their primary function is to retard groundwater flow. Other materials including zeolites, metals, and dessicants are considered as special-purpose additives. Materials that tend to hydrolyze and lead to porosity reduction, such as silicates, oxides, and sulfates, have also been suggested as packing materials. All these types of materials are also considered as components of tailored mixtures to achieve a broad range of packing material performance. Some of these materials are reviewed, along with proposed candidate materials, with respect to the properties required to function in a salt repository. The investigation of packing materials is composed of five studies which are discussed below. Initial candidates will consist of calcium hydroxide, a sodium silicate, and a cement-gypsum mixture in addition to the reference crushed salt. Consequently these tests will be necessary to determine properties of individual components and to optimize properties of mixtures. 13 refs., 7 figs., 1 tab

Final repository search together with the citizens. Information, consultation, dialogue, participation

International Nuclear Information System (INIS)

Mueller, Monika C.M.

2013-01-01

The documentation on the Loccum meeting 2013 includes contributions on the following topics: Public participation for the final repository search; Lessons learned from the past; Public participation: what is expected? Experiences of repository operators on public participation; The TRIPLEX concept; From Gorleben to the law on final repository search: a long and a short story; Public participation concerning radioactive waste storage; The public has to be informed on the radioactive waste problem and the possible solutions; After consensus is before consensus - German final repository conflict between legislation and simulated public participation; Political concept of public participation; A fast final repository law will not bring about social peace; Good public participation on final repository search - requirements, challenges, questions and approaches.

Sample management implementation plan: Salt Repository Project

International Nuclear Information System (INIS)

1987-01-01

The purpose of the Sample Management Implementation Plan is to define management controls and building requirements for handling materials collected during the site characterization of the Deaf Smith County, Texas, site. This work will be conducted for the US Department of Energy Salt Repository Project Office (SRPO). The plan provides for controls mandated by the US Nuclear Regulatory Commission and the US Environmental Protection Agency. Salt Repository Project (SRP) Sample Management will interface with program participants who request, collect, and test samples. SRP Sample Management will be responsible for the following: (1) preparing samples; (2) ensuring documentation control; (3) providing for uniform forms, labels, data formats, and transportation and storage requirements; and (4) identifying sample specifications to ensure sample quality. The SRP Sample Management Facility will be operated under a set of procedures that will impact numerous program participants. Requesters of samples will be responsible for definition of requirements in advance of collection. Sample requests for field activities will be approved by the SRPO, aided by an advisory group, the SRP Sample Allocation Committee. This document details the staffing, building, storage, and transportation requirements for establishing an SRP Sample Management Facility. Materials to be managed in the facility include rock core and rock discontinuities, soils, fluids, biota, air particulates, cultural artifacts, and crop and food stuffs. 39 refs., 3 figs., 11 tabs

Salt Repository Project: FY 85 technical project plan

International Nuclear Information System (INIS)

1985-07-01

The FY 85 technical plan for the Salt Repository Project is briefly presented. The objectives of the project in relation to the Civilian Radioactive Waste Management Program are discussed, and the technical activities directed toward accomplishing these objectives are detailed. A budget is presented for each of the Level 2 work breakdown structure tasks (Systems, Waste Package, Site, Repository, Regulatory and Institutional, Exploratory Shaft, Test Facilities, Land Acquisition, and Project Management) in the various sections. An overall description, current status, and planned activities are presented for each of the subtasks which make up the above-mentioned Level 2 tasks. A strategy diagram and a master schedule are included and each of the milestones is also listed chronologically in the sections

Salt Repository Project. FY-84 technical project plan

International Nuclear Information System (INIS)

1984-08-01

The FY 84 technical plans for the Salt Repository Project (SRP) are briefly presented. The objectives of the project in relation to the Civilian Radioactive Waste Management (CRWM) program are discused and the technical activities directed toward accomplishing these objectives are detailed. A budget is presented for each of the Level 2 Work Breakdown Structure Tasks (Systems, Waste Package, Site, Repository, Regulatory and Institutional, Test Facilities, Exploratory Shaft, Land Acquisition, and Program Management) in an appendix. An overall description, current status, and planned activities are presented for each of the subtasks which make up the above-mentioned Level 2 tasks. Milestones and their definitions for the plan year, as well as milestones for the outyears are also presented at this same subtask level for each subtask

Asse salt mine nuclear waste repository simulation experiments

International Nuclear Information System (INIS)

Coyle, A.J.

1983-01-01

The field tests underway in Asse, Federal Republic of Germany are dicected toward the development of test plans, techniques and equipment to be used in Exploratory Shafts or At Depth Test Facilities confirmation tests. These simulated repository tests will also provide information which address the following issues: brine migration (liquid and vapor); radiation effects of gamma rays; gas generation caused by radiation and corrosion; accelerated corrosion and leaching; altered properties of salt (the effects of heat, radiation and brine); and the effects of heat and radiation on test assemblies, instruments, and various materials exposed to repository conditions. This paper is a status of the first 82 days of operation of the Asse Brine Migration Tests, which were initiated on May 25, 1983. 6 references

Requirements of actual final repository concepts for different host rock formations. Final report; Anforderungen an aktuelle Endlagerkonzepte fuer unterschiedliche Wirtsgesteinsformationen. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Fass, Thorsten; Hartwig-Thurat, Eva; Krischer, Angelika; Lambers, Ludger; Larue, Juergen; Uhlmann, Stephan; Weyand, Torben

2017-08-15

In the frame of the research project the basic requirements and technical safety specifications with respect to the retrievability of stored radioactive wastes for the different final repository concepts based on the host rock formations occurring in Germany are presented. Existing international disposal concepts for clay/claystone, granite and salt are described and compared to the actual German regulatory requirements. The safety engineering relations between stock piling and possible retrieval are described and evaluated.

Salt repository project: Technical progress report for the quarter 1 April--30 June 1987

International Nuclear Information System (INIS)

1987-01-01

This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of Energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation

Salt Repository Project technical progress report for the quarter 1 January--31 March 1987

International Nuclear Information System (INIS)

1988-03-01

This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation. 23 refs., 1 fig

Evaluation of iron-base materials for waste package containers in a salt repository

International Nuclear Information System (INIS)

Westerman, R.E.; Nelson, J.L.; Kuhn, W.L.; Basham, S.G.; Moak, D.A.; Pitman, S.G.

1983-11-01

Design studies for high-level nuclear waste packages for salt repositories have identified low-carbon steel as a candidate material for containers. Among the requirements are strength, corrosion resistance, and fabricability. The studies of the corrosion resistance and structural stability of iron-base materials (particularly low-carbon steel) are treated in this paper. The materials have been exposed in brines that are characteristic of the potential sites for salt repositories. The effects of temperature, radiation level, oxygen level and other parameters are under investigation. The initial development of corrosion models for these environments is presented with discussion of the key mechanisms under consideration. 6 references, 5 figures

Aspects on the gas generation and migration in repositories for high level waste in salt formations

International Nuclear Information System (INIS)

Ruebel, Andre; Buhmann, Dieter; Meleshyn, Artur; Moenig, Joerg; Spiessl, Sabine

2013-07-01

In a deep geological repository for high-level waste, gases may be produced during the post-closure phase by several processes. The generated gases can potentially affect safety relevant features and processes of the repository, like the barrier integrity, the transport of liquids and gases in the repository and the release of gaseous radionuclides from the repository into the biosphere. German long-term safety assessments for repositories for high-level waste in salt which were performed prior 2010 did not explicitly consider gas transport and the consequences from release of volatile radionuclides. Selected aspects of the generation and migration of gases in repositories for high-level waste in a salt formation are studied in this report from the viewpoint of the performance assessment. The knowledge on the availability of water in the repository, in particular the migration of salt rock internal fluids in the temperature field of the radioactive waste repository towards the emplacement drifts, was compiled and the amount of water was roughly estimated. Two other processes studied in this report are on the one hand the release of gaseous radionuclides from the repository and their potential impact in the biosphere and on the other hand the transport of gases along the drifts and shafts of the repository and their interaction with the fluid flow. The results presented show that there is some gas production expected to occur in the repository due to corrosion of container material from water disposed of with the backfill and inflowing from the host rock during the thermal phase. If not dedicated gas storage areas are foreseen in the repository concept, these gases might exceed the storage capacity for gases in the repository. Consequently, an outflow of gases from the repository could occur. If there are failed containers for spent fuel, radioactive gases might be released from the containers into the gas space of the backfill and subsequently transported together

Assessment of Effectiveness of Geologic Isolation Systems: REFERENCE SITE INITIAL ASSESSMENT FOR A SALT DOME REPOSITORY

Energy Technology Data Exchange (ETDEWEB)

Harwell, M. A.; Brandstetter, A.; Benson, G. L.; Raymond, J. R.; Brandley, D. J.; Serne, R. J.; Soldat, J. K.; Cole, C. R.; Deutsch, W. J.; Gupta, S. K.; Harwell, C. C.; Napier, B. A.; Reisenauer, A. E.; Prater, L. S.; Simmons, C. S.; Strenge, D. L.; Washburn, J. F.; Zellmer, J. T.

1982-06-01

As a methodology demonstration for the Office of Nuclear Waste Isolation (ONWI), the Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program conducted an initial reference site analysis of the long-term effectiveness of a salt dome repository. The Hainesville Salt Dome in Texas was chosen to be representative of the Gulf Coast interior salt domes; however, the Hainesville Site has been eliminated as a possible nuclear waste repository site. The data used for this exercise are not adequate for an actual assessment, nor have all the parametric analyses been made that would adequately characterize the response of the geosystem surrounding the repository. Additionally, because this was the first exercise of the complete AEGIS and WASTE Rock Interaction Technology (WRIT) methodology, this report provides the initial opportunity for the methodology, specifically applied to a site, to be reviewed by the community outside the AEGIS. The scenario evaluation, as a part of the methodology demonstration, involved consideration of a large variety of potentially disruptive phenomena, which alone or in concert could lead to a breach in a salt dome repository and to a subsequent transport of the radionuclides to the environment. Without waste- and repository-induced effects, no plausible natural geologic events or processes which would compromise the repository integrity could be envisioned over the one-million-year time frame after closure. Near-field (waste- and repository-induced) effects were excluded from consideration in this analysis, but they can be added in future analyses when that methodology development is more complete. The potential for consequential human intrusion into salt domes within a million-year time frame led to the consideration of a solution mining intrusion scenario. The AEGIS staff developed a specific human intrusion scenario at 100 years and 1000 years post-closure, which is one of a whole suite of possible scenarios. This scenario

Compliance status summaries for federal and state statutory directives that apply to the Salt Repository Project at the Deaf Smith County Site, Texas

International Nuclear Information System (INIS)

1986-07-01

This document contains statutory summaries, checklists of compliance requirements, status summaries, and lists of information needs for the environmental and health and safety statutory directives at Federal and State levels that apply to the Salt Repository Project at the Deaf Smith County Site, Texas. Statutes that apply in general to any repository project but not specifically to the Deaf Smith are not included. The information herein supplements the Salt Repository Project Statutory Compliance Plan and the Salt Repository Project Permitting Management Plan by providing lengthy details on statutory directives, compliance requirements, information needs, and the overall status of the environmental and health and safety compliance program for the Salt Repository Project at the Deaf Smith County Site, Texas

Conceptual model for regional radionuclide transport from a salt dome repository: a technical memorandum

International Nuclear Information System (INIS)

Kier, R.S.; Showalter, P.A.; Dettinger, M.D.

1980-01-01

Disposal of high-level radioactive wastes is a major environmental problem influencing further development of nuclear energy in this country. Salt domes in the Gulf Coast Basin are being investigated as repository sites. A major concern is geologic and hydrologic stability of candidate domes and potential transport of radionuclides by groundwater to the biosphere prior to their degradation to harmless levels of activity. This report conceptualizes a regional geohydrologic model for transport of radionuclides from a salt dome repository. The model considers transport pathways and the physical and chemical changes that would occur through time prior to the radionuclides reaching the biosphere. Necessary, but unknown inputs to the regional model involve entry and movement of fluids through the repository dome and across the dome-country rock interface and the effect on the dome and surrounding strata of heat generated by the radioactive wastes

Proceedings of the 7th US/German Workshop on Salt Repository Research, Design, and Operation.

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Steininger, Walter [Karisruhe Inst. of Technology (Germany); Bollingerfehr, Willhelm [DBE TECHNOLOGY GmbH (Germany)

2017-01-01

The 7th US/German Workshop on Salt Repository Research, Design, and Operation was held in Washington, DC on September 7-9, 2016. Over fifty participants representing governmental agencies, internationally recognized salt research groups, universities, and private companies helped advance the technical basis for salt disposal of radioactive waste. Representatives from several United States federal agencies were able to attend, including the Department of Energy´s Office of Environmental Management and Office of Nuclear Energy, the Environmental Protection Agency, the Nuclear Regulatory Commission, and the Nuclear Waste Technical Review Board. A similar representation from the German ministries showcased the covenant established in a Memorandum of Understanding executed between the United States and Germany in 2011. The US/German workshops´ results and activities also contribute significantly to the Nuclear Energy Agency Salt Club repository research agenda.

Nuclear waste repository simulation experiments. Asse salt mine: Annual report 1984

International Nuclear Information System (INIS)

Rothfuchs, T.; Feddersen, H.K.; Schwarzianeck, P.; Staupendahl, G.; Coyle, A.J.; Kalia, H.; Eckert, J.

1985-01-01

This is the Second Annual Report (1984) which describes experiments simulating a nuclear waste repository at the 800 meter-level of the Asse Salt Mine in the Federal Republic of Germany. The report describes the Asse Salt Mine, the test equipment, and the pretest properties of the salt in the mine and in the vicinity of the test area. Also included are test data for the first sixteen months of operation on the following: brine migration rates, thermal mechanical behavior of the salt (including room closure, stress readings and thermal profiles) and borehole gas pressures. In addition to field data laboratory analyses of results are also included in this report. The duration of the experiment will be two years, ending in December 1985. (orig.)

Salt repository sealing materials development program: 5-year work plan

International Nuclear Information System (INIS)

Myers, L.B.

1986-06-01

This plan covers 5 years (fiscal years 1986 through 1990) of work in the repository sealing materials program to support design decisions and licensing activities for a salt repository. The plan covers a development activity, not a research activity. There are firm deliverables as the end points of each part of the work. The major deliverables are: development plans for code development and materials testing; seal system components models; seal system performance specifications; seal materials specifications; and seal materials properties ''handbook.'' The work described in this plan is divided into three general tasks as follows: mathematical modeling; materials studies (salt, cementitious materials, and earthen materials); and large-scale testing. Each of the sections presents an overview, status, planned activities, and summary of program milestones. This plan will be the starting point for preparing the development plans described above, but is subject to change if preparation of the work plan indicates that a different approach or sequence is preferable to achieve the ultimate goal, i.e., support of design and licensing

Salt Repository Project input to seismic design: Revision 0

International Nuclear Information System (INIS)

1987-12-01

The Salt Repository Program (SRP) Input to Seismic Design (ISD) documents the assumptions, rationale, approaches, judgments, and analyses that support the development of seismic-specific data and information to be used for shaft design in accordance with the SRP Shaft Design Guide (SDG). The contents of this document are divided into four subject areas: (1) seismic assessment, (2) stratigraphy and material properties for seismic design, (3) development of seismic design parameters, and (4) host media stability. These four subject areas have been developed considering expected conditions at a proposed site in Deaf Smith County, Texas. The ISD should be used only in conjunction with seismic design of the exploratory and repository shafts. Seismic design considerations relating to surface facilities are not addressed in this document. 54 refs., 55 figs., 18 tabs

Salt Repository Project transportation system interface requirements: Transportation system/repository receiving facility interface requirements

International Nuclear Information System (INIS)

Smith, L.A.; Insalaco, J.W.; Trainer, T.A.

1988-01-01

This report is a preliminary review of the interface between the transportation system and the repository receiving facility for a nuclear waste mined geologic disposal system in salt. Criteria for generic cask and facility designs are developed. These criteria are derived by examining the interfaces that occur as a result of the operations needed to receive nuclear waste at a repository. These criteria provide the basis for design of a safe, operable, practical nuclear waste receiving facility. The processing functions required to move the shipping unit from the gate into the unloading area and back to the gate for dispatch are described. Criteria for a generic receiving facility are discussed but no specific facility design is presented or evaluated. The criteria are stated in general terms to allow application to a wide variety of cask and facility designs. 9 refs., 6 figs., 4 tabs

Effects of gaseous radioactive nuclides on the design and operation of repositories for spent LWR fuel in rock salt

International Nuclear Information System (INIS)

Jenks, G.H.

1979-12-01

Information relating to the identities and amounts of gaseous radionuclides present in spent LWR fuel and to their release from canistered spent fuel under plausible storage and disposal conditions was assembled, reviewed, and analyzed. Information was also reviewed and analyzed on several other subjects that relate to the integrity of the carbon steel canister in which the spent fuel is to be encapsulated and to the expected rates of transfer of gaseous radionuclides through crushed salt backfill within a disposal room in a reference repository in rock salt. The advantages and disadvantages were considered for several different canister-backfill materials, and recommendations were made regarding preferred materials. Other recommendations relate to encapsulation procedures and specifications and to needs for additional experimental studies. The objective of this work was to provide reference information, conclusions, and recommendations that could be used to establish design and operating conditions and procedures for a bedded salt repository for spent LWR fuel and that could also be used to help evaluate the safety of the repository. The results of this work will also generally apply to spent fuel repositories in domal salt. However, because the domal salt may have little or no brine inclusions within it, there may be little or no possibility that brine will migrate into open spaces around an emplaced canister. Addordingly, some of the concerns that result from the possible occurrence of brine migration in bedded salt may be of no importance in domal salt

Classifying decommissioning wastes for allocation to appropriate final repositories

International Nuclear Information System (INIS)

Alder, J.C.; Tunaboylu, K.

1982-01-01

For the safe disposal of radioactive wastes in different repositories, it is of advantage to classify them in well-defined conditioned categories, appropriate for final disposal. These categories, the so-called waste sorts are characterized by similar radionuclide distribution, similar nuclide-specific activity concentrations and similar waste matrix. A methodology is presented for classifying decommissioning wastes and is applied to the decommissioning wastes arising from a Swiss program of 6 GWe. The amounts and nuclide-specific activity inventories of the decommissioning waste sorts have been estimated. A first allocation into two different repository types has been performed. Such a classification enables one to define the source parameters for repository safety analysis and allows one to allocate the different waste categories into appropriate final repositories. This work presents a first iteration to determine which waste sorts belong to which repository type. The characteristics of waste sorts have to be better defined and the protective strength of the repository barriers has to be optimized. 7 references, 2 figures, 4 tables

Natural analogues for containment-providing barriers for a HLW repository in salt

Energy Technology Data Exchange (ETDEWEB)

Wolf, J.; Noseck, U.

2015-06-15

In 2005, a German research project was started to develop a novel approach to prove safety for a HLW repository in a salt formation, to refine the safety concept, to identify open scientific issues and to define necessary R&D work. This project aimed at identifying the key information for a HLW repository in salt. One important question is how this information may be best fulfilled by natural analogue studies. This question is answered by starting a review of the required key information needs of the safety case (post-closure phase) in order to assess whether or not these requirements can be supported by natural analogues information. In order to structure the review and to address the key elements of the safety concepts, three types of natural analogues are distinguished: (i) natural analogues for the integrity of the geological barrier, (ii) natural analogues for the integrity of the geotechnical barriers and (iii) natural analogues for release scenarios. For the safety case in salt type (i) and (ii) are of highest importance and are treated in this paper. The assessment documented in this paper on the one hand indicates the high potential benefit of natural analogues for a safety case in salt and on the other hand helps to focus the available human and financial resources for the safety case on the most safety-relevant aspects. (authors)

Mass transfer in a salt repository

International Nuclear Information System (INIS)

Pigford, T.H.; Chambre, P.L.

1985-05-01

To meet regulatory requirements for radioactive waste in a salt repository it is necessary to predict the rates of corrosion of the waste container, the release rates of radionuclides from the waste package, and the cumulative release of radionuclides into the accessible environment. The mechanisms that may control these rates and an approach to predicting these rates from mass-transfer theory are described. This new mechanistic approach is suggested by three premises: (a) a brine inclusion originally in a salt crystal moves along grain boundaries after thermal-induced migration out of the crystal, (b) brine moves along a grain boundary under the influence of a pressure gradient, and (c) salt surrounding a heat-generating waste package will soon creep and consolidate as a monolithic medium surrounding and in contact with the waste package. After consolidation there may be very little migration of intergranular and intragranular brine to the waste package. The corrosion rate of the waste container may then be limited by the rate at which brine reaches the container and may be calculable from mass-transfer theory, and the rate at which dissolved radionuclides leave the waste package may be limited by molecular diffusion in intragranular brine and may be calculable from mass-transfer theory. If porous nonsalt interbeds intersect the waste-package borehole, the release rate of dissolved radionuclides to interbed brine may also be calculable from mass-transfer theory. The logic of these conclusions is described, as an aid in formulating the calculations that are to be made

Radiological consequences of a human intrusion in a nuclear waste repository in a salt formation

International Nuclear Information System (INIS)

Jacquier, P.; Raimbault, P.

1989-07-01

The assessment of the consequences of human intrusion scenarios for a repository is very important for salt formations, since this material has an undeniable economic interest. In this work, the scenario considers the solution mining of salt for human consumption: salt is extracted from a cavern; by leaching, this cavern enlarges and uncovers the waste, which falls down into the sump. It was assumed that the intrusion takes place either 500 years or 2500 years after the closing of the repository. High-level vitrified waste or alpha cemented waste were considered. This paper displays the assumptions made and, using a simplified modelling of the phenomena, the estimation of the radiological consequences due to ingestion of contamined sals. A sensitivity/uncertainty analysis is presented which emphasizes several fields where experimental studies have to be pursued or launched [fr

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 8. Repository preconceptual design studies: salt

International Nuclear Information System (INIS)

1978-04-01

This volume, Volume 8 ''Repository Preconceptual Design Studies: Salt,'' is one of a 23-volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provides a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This document describes a preconceptual design for a nuclear waste storage facility in salt. The facility design consists of several chambers excavated deep within a geologic formation together with access shafts and supportive surface structures. The facility design provides for: receiving and unloading waste containers; lowering them down shafts to the mine level; transporting them to the proper storage area, and emplacing them in mined storage rooms. Drawings of the facility design are contained in TM-36/9, ''Drawings for Repository Preconceptual Design Studies: Salt.''

Utilities availability report for seven candidate salt sites: Final draft

International Nuclear Information System (INIS)

1984-12-01

Stearns Catalytic Corporation (SC) conducted a study of availability and accessibility of electric power and natural gas supplies for each of the seven candidate sites in salt for a nuclear waste repository. The objective of this study is to indicate the existing or potential availability of adequate electric power and natural gas supplies, together with representative routing of reasonable access corridors for utility lines, for the candidate sites at Richton and Cypress Creek Domes in Mississippi, Vacherie Dome in Louisiana, Swisher and Deaf Smith Counties in Texas, and Davis and Lavender Canyons in Utah. The report describes the major characteristics of each supply and the representative routes by which each supply could be connected to the assumed respective repository site. Included are a brief narrative, maps showing representative utilities access routes, and a summary tabulation of relevant data. The supply routes used in this study are not necessarily the recommended, preferred, or selected routes. No decision affecting the final location of the preferred route has been made, therefore the routes used in this study are not to be construed as an implied decision. The routes and supply sources used in this study are for comparative purposes only, as no final selections will be made prior to site characterization

Performance analysis of conceptual waste package designs in salt repositories

International Nuclear Information System (INIS)

Jansen, G. Jr.; Raines, G.E.; Kircher, J.F.

1984-01-01

A performance analysis of commercial high-level waste and spent fuel conceptual package designs in reference repositories in three salt formations was conducted with the WAPPA waste package code. Expected conditions for temperature, stress, brine composition, radiation level, and brine flow rate were used as boundary conditions to compute expected corrosion of a thick-walled overpack of 1025 wrought steel. In all salt formations corrosion by low Mg salt-dissolution brines typical of intrusion scenarios was too slow to cause the package to fail for thousands of years after burial. In high Mg brines judged typical of thermally migrating brines in bedded salt formations, corrosion rates which would otherwise have caused the packages to fail within a few hundred years were limited by brine availability. All of the brine reaching the package was consumed by reaction with the iron in the overpack, thus preventing further corrosion. Uniform brine distribution over the package surface was an important factor in predicting long package lifetimes for the high Mg brines. 14 references, 15 figures

Review of Y/OWI/TM-36: repository design performance in salt, granite, shale or basalt

International Nuclear Information System (INIS)

Talbot, R.; Nair, O.B.

1979-09-01

As part of the ongoing work by the Lawrence Livermore Laboratory to evaluate repository design performance, this memorandum presents a review of the preconceptual repository design described in Y/OWI/TM-36, Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations, April 1978. The purpose of this review is: to assess the adequacy of the design procedures and assumptions; to identify inappropriate or unsubstantiated design issues; to identify areas where additional numerical analyses may be required; and to develop data for inclusion in a reference repository design. The preconceptual repository design is presented in the form of 23 volumes of data base, analyses, and design layouts for four rock types: bedded salt, shale, granite and basalt. This memorandum reviews all four repository designs

Salt Repository Project waste emplacement mode decision paper: Revison 1

International Nuclear Information System (INIS)

1987-08-01

This paper provides a recommendation as to the mode of waste emplacement to be used as the current basis for site characterization activity for the Deaf Smith County, Texas, high level nuclear waste repository site. It also presents a plan for implementing the recommendation so as to provide a high level of confidence in the project's success. Since evaluations of high-level waste disposal in geologic repositories began in the 1950s, most studies emplacement in salt formations employed the vertical orientation for emplacing waste packages in boreholes in the floor of the underground facility. This orientation was used in trials at Project Salt Vault in the 1960s. The Waste Isolation Pilot Plant (WIPP) has recently settled on a combination of vertical and horizontal modes for various waste types. This paper analyzes the information available and develops a project position upon which to base current site characterization activities. The position recommended is that the SRP should continue to use the vertical waste emplacement mode as the reference design and to carry the horizontal mode as a ''passive'' alternative. This position was developed based upon the conclusions of a decision analysis, risk assessment, and cost/schedule impact assessment. 52 refs., 6 figs., 1 tab

Performance Assessment of a Generic Repository in Bedded Salt for DOE-Managed Nuclear Waste

Science.gov (United States)

Stein, E. R.; Sevougian, S. D.; Hammond, G. E.; Frederick, J. M.; Mariner, P. E.

2016-12-01

A mined repository in salt is one of the concepts under consideration for disposal of DOE-managed defense-related spent nuclear fuel (SNF) and high level waste (HLW). Bedded salt is a favorable medium for disposal of nuclear waste due to its low permeability, high thermal conductivity, and ability to self-heal. Sandia's Generic Disposal System Analysis framework is used to assess the ability of a generic repository in bedded salt to isolate radionuclides from the biosphere. The performance assessment considers multiple waste types of varying thermal load and radionuclide inventory, the engineered barrier system comprising the waste packages, backfill, and emplacement drifts, and the natural barrier system formed by a bedded salt deposit and the overlying sedimentary sequence (including an aquifer). The model simulates disposal of nearly the entire inventory of DOE-managed, defense-related SNF (excluding Naval SNF) and HLW in a half-symmetry domain containing approximately 6 million grid cells. Grid refinement captures the detail of 25,200 individual waste packages in 180 disposal panels, associated access halls, and 4 shafts connecting the land surface to the repository. Equations describing coupled heat and fluid flow and reactive transport are solved numerically with PFLOTRAN, a massively parallel flow and transport code. Simulated processes include heat conduction and convection, waste package failure, waste form dissolution, radioactive decay and ingrowth, sorption, solubility limits, advection, dispersion, and diffusion. Simulations are run to 1 million years, and radionuclide concentrations are observed within an aquifer at a point approximately 4 kilometers downgradient of the repository. The software package DAKOTA is used to sample likely ranges of input parameters including waste form dissolution rates and properties of engineered and natural materials in order to quantify uncertainty in predicted concentrations and sensitivity to input parameters. Sandia

Final repositories for high-level radioactive waste; Endlagerung hochradioaktiver Abfaelle

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-10-15

The brochure on final repositories for high-level radioactive waste covers the following issues: What is the origin of radioactive wastes? How large are the waste amounts? What is going to happen with the wastes? What is the solution for the Waste disposal? A new site search is started. Safety requirements for the final disposal of high-level radioactive wastes. Comparison of host rocks. Who is responsible and who will pay? Final disposal of high-level radioactive wastes worldwide. Short summary: History of the search for a final repository for high-level radioactive wastes in Germany.

Selection and durability of seal materials for a bedded salt repository: preliminary studies

International Nuclear Information System (INIS)

Roy, D.M.; Grutzeck, M.W.; Wakeley, L.D.

1983-11-01

This report details preliminary results of both experimental and theoretical studies of cementitious seal materials for use in a proposed nuclear waste repository in bedded salt. Effects of changes in bulk composition and environment upon phase stability and physical/mechanical properties have been evaluated for more than 25 formulations. Bonding and interfacial characteristics of the region between host rock and seal material or concrete aggregate and cementitious matrix for selected formulations have been studied. Compatibilities of clays and zeolites in brines typical of the SE New Mexico region have been investigated, and their stabilities reviewed. Results of these studies have led to the conclusion that cementitious materials can be formulated which are compatible with the major rock types in a bedded salt repository environment. Strengths are more than adequate, permeabilities are consistently very low, and elastic moduli generally increase only very slightly with time. Seal formulation guidelines and recommendations for present and future work are presented. 73 references, 25 figures, 61 tables

Spent fuel stability under repository conditions - final report of the european project

International Nuclear Information System (INIS)

Poinssot, Ch.; Ferry, C.; Kelm, M.; Cavedon, J.M.; Corbel, C.; Jegou, Ch.; Lovera, P.; Miserque, F.; Poulesquen, A.; Grambow, B.; Andriambololona, Z.; Martinez-Esparza, A.; Kelm, M.; Loida, A.; Rondinella, V.; Wegen, D.; Spahiu, K.; Johnson, L.; Cachoir, Ch.; Lemmens, K.; Quinones, J.; Bruno, J.; Christensen, H.; Grambow, B.; Pablo, J. de

2005-01-01

This report is the final report of the European Project 'Spent Fuel Stability under Repository Conditions' (FIKW-CT-2001-00192 SFS) funded by the European Commission from Nov.2000 to Oct.2004. Gathering the work performed by 13 partners from 6 countries, it aims to specifically focus on the spent nuclear fuel long term alteration in deep repository and the subsequent radionuclides release rate as a function of time. This report synthesised the wide experimental work performed within this project and enlightens the major outcomes, which can be summarised as follow: - A new model for defining the Instant Release Fraction was developed in order to consider the potential fuel evolution before the water penetrates the canister. Quantitative assessment has been produced and shows a significant contribution to the long term dose; - Based on new experimental data, kinetic radiolytic scheme have been upgraded and are used to determine the amount of oxidants produced at the fuel/water interface; - The existence of a dose threshold below which the water radiolysis does not influence the fuel alteration has been demonstrated and occurs between 3.5 and 33 MBq.g UO21. Above the threshold, the fuel alteration rates is directly related to the dose rate. - Hydrogen was experimentally demonstrated to be an efficient oxidants scavenger preventing therefore the fuel oxidation. Molecular mechanism still need to be understood. - Finally, a new Matrix Alteration Model integrating most of the SFS results (apart of the hydrogen effect) has been developed and used to assess the fuel long tern stability in representative conditions of deep repository in salt, clay-rock and granite. The breadth of the results and the significance of the conclusions testify of the success of the collaboration within the project. (authors)

Brine migration test - Asse salt mine, Federal Republic of Germany

International Nuclear Information System (INIS)

Rothfuchs, T.; Wieczorek, K.; Feddersen, H.K.; Staupendahl, G.; Coyle, A.J.; Kalia, H.; Eckert, J.

1988-03-01

This document is the final report on the Cooperative German-American 'Brine Migration Tests' that were performed at the Asse Salt Mine in the Federal Republic of Germany (FRG), the Office of Nuclear Waste Isolation (ONWI), Columbus, Ohio, and the Institut fuer Tieflagerung (IfT), Braunschweig, of the Gesellschaft fuer Strahlen- und Umweltforschung mbH Muenchen (GSF). Final test and equipment design as well as manufacturing and installation was carried out by Westinghouse Electric Corporation. The tests were designed to simulate a nuclear waste repository to measure the effects of heat and gamma radiation on brine migration, salt decrepitation, disassociation of brine, and gases collected. The thermal mechanical behavior of salt, such as room closure, stresses and changes of the properties of salt are measured and compared with predicted behavior. The performance of an array of candidate waste package materials, test equipment and procedures under repository conditions will be evaluated with a view towards future in-depth testing of potential repository sites. (orig./RB)

SKB's safety case for a final repository license application

International Nuclear Information System (INIS)

Hedin, Allan; Andersson, Johan

2014-01-01

The safety assessment SR-Site is a main component in SKB's license application, submitted in March 2011, to construct and operate a final repository for spent nuclear fuel at Forsmark in the municipality of Oesthammar, Sweden. Its role in the application is to demonstrate long-term safety for a repository at Forsmark. The assessment relates to the KBS-3 disposal concept in which copper canisters with a cast iron insert containing spent nuclear fuel are surrounded by bentonite clay and deposited at approximately 500 m depth in saturated, granitic rock. The principal regulatory acceptance criterion, issued by the Swedish Radiation Safety Authority (SSM), requires that the annual risk of harmful effects after closure not exceed 10 -6 for a representative individual in the group exposed to the greatest risk. SSM's regulations also imply that the assessment time for a repository of this type is one million years after closure. The licence applied for is one in a stepwise series of permits, each requiring a safety report. The next step concerns a permit to start excavation of the repository and requires a preliminary safety assessment report (PSAR) covering both operational and post-closure safety. Later steps include permission to commence trial operation, to commence regular operation and to close the final repository. (authors)

Review of geochemical measurement techniques for a nuclear waste repository in bedded salt

International Nuclear Information System (INIS)

Knauss, K.G.; Steinborn, T.L.

1980-01-01

A broad, general review is presented of geochemical measurement techniques that can provide data necessary for site selection and repository effectiveness assessment for a radioactive waste repository in bedded salt. The available measurement techniques are organized according to the parameter measured. The list of geochemical parameters include all those measurable geochemical properties of a sample whole values determine the geochemical characteristics or behavior of the system. For each technique, remarks are made pertaining to the operating principles of the measurement instrument and the purpose for which the technique is used. Attention is drawn to areas where further research and development are needed

Proceedings of the 8th US/German Workshop on Salt Repository Research Design and Operation.

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [RESPEC, Rapid City, SD (United States); Steininger, Walter [Karlsruhe Inst. of Technology (KIT) (Germany); Bollingerfehr, Wilhelm [DBE Technology, Peine (Germany); Kuhlman, Kristopher L [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dunagan, Sean [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-02-01

This document records the Proceedings of the 2017 gathering of salt repository nations. In a spirit of mutual support, technical issues are dissected, led capably by subject matter experts. As before, it is not possible to explore all contemporary issues regarding nuclear waste disposal in salt formations. Instead, the group focused on a few selected issues to be pursued in depth, while at the same time acknowledging and recording ancillary issues.

Status of work on the final repository concept concerning direct disposal of spent fuel rods in fuel rod casks (BSK)

International Nuclear Information System (INIS)

Filbert, W.; Wehrmann, J.; Bollingerfehr, W.; Graf, R.; Fopp, S.

2008-01-01

The reference concept in Germany on direct final storage of spent fuel rods is the burial of POLLUX containers in the final repository salt dome. The POLLUX container is self-shielded. The final storage concept also includes un-shielded borehole storage of high-level waste and packages of compacted waste. GNS has developed a spent fuel container (BSK-3) for unshielded borehole storage with a mass of 5.2 tons that can carry the fuel rods of three PWR reactors of 9 BWR reactors. The advantages of BSK storage include space saving, faster storage processes, less requirements concerning technical barriers, cost savings for self-shielded casks.

Coupled modelling of convergence, steel corrosion, gas production and brine flow in a rock salt repository

International Nuclear Information System (INIS)

Becker, D.A.; Hirsekorn, R.P.

2013-01-01

This poster presents the global simulation of the behaviour of thick-walled steel containers piled up in a borehole in a rock salt repository. The simulation takes into account: the convergence by the creeping of rock salt, the backfill and waste compaction, the porosity dependent flow resistance, the anaerobic corrosion (iron to magnetite transformation, gas production, brine consumption, water consumption and salt precipitation) and pressure development. Mechanical influence of corrosion has not yet been taken into account in the integrated code LOPOS

Thermal Analysis of Disposal of High-Level Nuclear Waste in a Generic Bedded Salt repository using the Semi-Analytical Method.

Energy Technology Data Exchange (ETDEWEB)

Hadgu, Teklu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Matteo, Edward N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

An example case is presented for testing analytical thermal models. The example case represents thermal analysis of a generic repository in bedded salt at 500 m depth. The analysis is part of the study reported in Matteo et al. (2016). Ambient average ground surface temperature of 15°C, and a natural geothermal gradient of 25°C/km, were assumed to calculate temperature at the near field. For generic salt repository concept crushed salt backfill is assumed. For the semi-analytical analysis crushed salt thermal conductivity of 0.57 W/m-K was used. With time the crushed salt is expected to consolidate into intact salt. In this study a backfill thermal conductivity of 3.2 W/m-K (same as intact) is used for sensitivity analysis. Decay heat data for SRS glass is given in Table 1. The rest of the parameter values are shown below. Results of peak temperatures at the waste package surface are given in Table 2.

Modeling of waste/near field interactions for a waste repository in bedded salt: the Dynamic Network (DNET) model

International Nuclear Information System (INIS)

Cranwell, R.M.

1983-01-01

The Fuel Cycle Risk Analysis Division of Sandia National Laboratories has been funded by the US Nuclear Regulatory Commission to develop a methodology for use in assessing the long-term risk from the disposal of radioactive wastes in deep geologic formations. As part of this program, the Dynamic Network (DNET) model was developed to investigate waste/near field interactions associated with the disposal of radioactive wastes in bedded salt formations. The model is a quasi-multi-dimensional network model with capabilities for simulating processes such as fluid flow, heat transport, salt dissolution, salt creep, and the effects of thermal expansion and subsedence on the rock units surrounding the repository. The use of DNET has been demonstrated in the analysis of a hypothetical disposal site containing a bedded salt formation as the host medium for the repository. An example of this demonstration analysis is discussed. Furthermore, the outcome of sensitivity analyses performed on the DNET model are presented

Preliminary constitutive properties for salt and nonsalt rocks from four potential repository sites

International Nuclear Information System (INIS)

Pfeifle, T.W.; Mellegard, K.D.; Senseny, P.E.

1983-07-01

Results are presented from laboratory strength and creep tests performed on salt and nonsalt specimens from the Richton Dome in Mississippi, the Vacherie Dome in Louisiana, the Permian Basin in Texas, and the Paradox Basin in Utah. The constititive properties obtained for salt are the elastic moduli and the failure envelope at 24 0 C and parameter values for the exponential-time creep law. Some additional data are presented to indicate how the elastic moduli and strength change with temperature. The nonsalt constitutive properties reported are the elastic moduli, the unconfined compressive strength and the tensile strength at 24 0 C. The properties given in this report will be used in subsequent numerical simulations that will provide information to assist in the screening and selection of site locations for a nuclear waste repository and to assist in the repository design at the selected site. The matrix of tests performed is the minimum effort required to obtain these constitutive properties. The preliminary values obtained will be supplemented by additional testing for sites that are selected for further investigation

The Microbiology of Subsurface, Salt-Based Nuclear Waste Repositories: Using Microbial Ecology, Bioenergetics, and Projected Conditions to Help Predict Microbial Effects on Repository Performance

International Nuclear Information System (INIS)

Swanson, Juliet S.; Cherkouk, Andrea; Arnold, Thuro; Meleshyn, Artur; Reed, Donald T.

2016-01-01

This report summarizes the potential role of microorganisms in salt-based nuclear waste repositories using available information on the microbial ecology of hypersaline environments, the bioenergetics of survival under high ionic strength conditions, and ''repository microbiology'' related studies. In areas where microbial activity is in question, there may be a need to shift the research focus toward feasibility studies rather than studies that generate actual input for performance assessments. In areas where activity is not necessary to affect performance (e.g., biocolloid transport), repository-relevant data should be generated. Both approaches will lend a realistic perspective to a safety case/performance scenario that will most likely underscore the conservative value of that case.

The Microbiology of Subsurface, Salt-Based Nuclear Waste Repositories: Using Microbial Ecology, Bioenergetics, and Projected Conditions to Help Predict Microbial Effects on Repository Performance

Energy Technology Data Exchange (ETDEWEB)

Swanson, Juliet S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Cherkouk, Andrea [Helmholtz-Zentrum Dresden-Rossendorf, Rossendorf (Germany); Arnold, Thuro [Helmholtz-Zentrum Dresden-Rossendorf, Rossendorf (Germany); Meleshyn, Artur [Gesellschaft fur Anlagen und Reaktorsicherheit, Braunschweig (Germany); Reed, Donald T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-11-17

This report summarizes the potential role of microorganisms in salt-based nuclear waste repositories using available information on the microbial ecology of hypersaline environments, the bioenergetics of survival under high ionic strength conditions, and “repository microbiology” related studies. In areas where microbial activity is in question, there may be a need to shift the research focus toward feasibility studies rather than studies that generate actual input for performance assessments. In areas where activity is not necessary to affect performance (e.g., biocolloid transport), repository-relevant data should be generated. Both approaches will lend a realistic perspective to a safety case/performance scenario that will most likely underscore the conservative value of that case.

Repository site data and information in bedded salt: Palo Duro Basin, Texas

International Nuclear Information System (INIS)

Tien, P.; Nimick, F.B.; Muller, A.B.; Davis, P.A.; Guzowski, R.V.; Duda, L.E.; Hunter, R.L.

1983-11-01

This report is a compilation of data from the literature on the Palo Duro Basin. The Palo Duro Basin is a structural basin, about 150 miles long and 80 miles wide, that is a part of the much larger Permian Basin. The US Department of Energy is investigating the Palo Duro Basin as a potentially suitable area for the site of a repository for the disposal of high-level radioactive waste. Sediments overlying the Precambrian basement range from about 5000 to about 11,000 ft in thickness and from Cambrian to Holocene in age. The strata in the Palo Duro Basin that are of primary interest to the Department of Energy are the bedded salts of the Permian San Andres Formation. The total thickness of the bedded salts is about 2000 ft. The geology of the Palo Duro Basin is well understood. A great deal of information exists on the properties of salt, although much of the available information was not collected in the Palo Duro Basin. Mineral resources are not currently being exploited from the center of the Palo Duro Basin at depth, although the possibility of exploration for and development of such resources can not be ruled out. The continued existence of salts of Permian age indicates a lack of any large amount of circulating ground water. The hydrology of the pre-Tertiary rocks, however, is currently too poorly understood to carry out detailed, site-specific hydrologic modeling with a high degree of confidence. In general, ground water flows from west to east in the Basin. There is little or no hydraulic connection between aquifers above and below the salt sequences. Potable water is pumped from the Ogallala aquifer. Most of the other aquifers yield only nonpotable water. More extensive hydrological data are needed for detailed future modeling in support of risk assessment for a possible repository for high-level waste in the Palo Duro Basin. 464 references

Interim performance specifications for conceptual waste-package designs for geologic isolation in salt repositories

International Nuclear Information System (INIS)

1983-06-01

The interim performance specifications and data requirements presented apply to conceptual waste package designs for all waste forms which will be isolated in salt geologic repositories. The waste package performance specifications and data requirements respond to the waste package performance criteria. Subject areas treated include: containment and controlled release, operational period safety, criticality control, identification, and waste package performance testing requirements. This document was generated for use in the development of conceptual waste package designs in salt. It will be revised as additional data, analyses, and regulatory requirements become available

Site specific statutory compliance planning for the salt repository project at the Deaf Smith County Site, Texas: Requirements, strategy, and status: Revision 4

International Nuclear Information System (INIS)

1986-06-01

This document and the requirements and actions it presents are addressed to the Deaf Smith County Site, Texas. The proposed actions upon which the plan is based are those described in Chapters 4 and 5 of the final EA for the site. Similarly, the environmental and health and safety requirements covered in the plan are those identified in the EA as being potentially applicable to the salt repository project at the Deaf Smith site. 12 figs., 8 tabs

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 16. Repository preconceptual design studies: BPNL waste forms in salt

International Nuclear Information System (INIS)

1978-04-01

This volume, Volume 16, ''Repository Preconceptual Design Studies: BPNL Waste Forms in Salt,'' is one of a 23 volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provide a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. This document describes a preconceptual design for a nuclear waste storage facility in salt. The waste forms assumed to arrive at the repository were supplied by Battelle Pacific Northwest Laboratories (BPNL). The facility design consists of several chambers excavated deep within a geologic formation together with access shafts and supportive surface structures. The facility design provides for: receiving and unloading waste containers; lowering them down shafts to the mine level; transporting them to the proper storage area and emplacing them in mined storage rooms. Drawings of the facility design are contained in TM-36/17, ''Drawings for Repository Preconceptual Design Studies: BPNL Waste Forms in Salt.''

Mass transport in bedded salt and salt interbeds

International Nuclear Information System (INIS)

Hwang, Y.; Pigford, T.H.; Chambre, P.L.; Lee, W.W.L.

1989-08-01

Salt is the proposed host rock for geologic repositories of nuclear waste in several nations because it is nearly dry and probably impermeable. Although experiments and experience at potential salt sites indicate that salt may contain brine, the low porosity, creep, and permeability of salt make it still a good choice for geologic isolation. In this paper we summarize several mass-transfer and transport analyses of salt repositories. The mathematical details are given in our technical reports

Dessicant materials screening for backfill in a salt repository

International Nuclear Information System (INIS)

Simpson, D.R.

1980-10-01

Maintaining an anhydrous environment around nuclear waste stored in a salt repository is a concern which can be alleviated by using a desiccant material for backfilling. Such a desiccant should desiccate a brine yet be non deliquescent, the hydrated product should have moderate thermal stability, and the desiccant should have a high capacity and be readily available. From a literature search MgO and CaO were identified for detailed study. These oxides, and an intimate mixture of the two obtained by calcining dolomite, were used in experiments to further determine their suitability. They proved to be excellent desiccants with a high water capacity. The hydrates of both have moderate thermal stability and a high water content. Both MgO and CaO react in an alkaline chloride brine forming oxychloride compounds with different waters of crystallization. Some of these compounds are the Sorel Cements. CaO hydrates to Ca(OH) 2 which carbonates with CO 2 in air to form CaCO 3 and release the hydrated water. Thus the intimate mixture of CaO and MgO from calcined dolomite may serve as a desiccant and remove CO 2 from the repository atmosphere

Dessicant materials screening for backfill in a salt repository

Energy Technology Data Exchange (ETDEWEB)

Simpson, D.R.

1980-10-01

Maintaining an anhydrous environment around nuclear waste stored in a salt repository is a concern which can be alleviated by using a desiccant material for backfilling. Such a desiccant should desiccate a brine yet be non deliquescent, the hydrated product should have moderate thermal stability, and the desiccant should have a high capacity and be readily available. From a literature search MgO and CaO were identified for detailed study. These oxides, and an intimate mixture of the two obtained by calcining dolomite, were used in experiments to further determine their suitability. They proved to be excellent desiccants with a high water capacity. The hydrates of both have moderate thermal stability and a high water content. Both MgO and CaO react in an alkaline chloride brine forming oxychloride compounds with different waters of crystallization. Some of these compounds are the Sorel Cements. CaO hydrates to Ca(OH)/sub 2/ which carbonates with CO/sub 2/ in air to form CaCO/sub 3/ and release the hydrated water. Thus the intimate mixture of CaO and MgO from calcined dolomite may serve as a desiccant and remove CO/sub 2/ from the repository atmosphere.

Nuclear waste repository simulation experiments, Asse salt mine, Federal Republic of Germany. Annual report 1984

International Nuclear Information System (INIS)

Rothfuchs, T.; Feddersen, H.K.; Schwarzianeck, P.; Staupendahl, G.; Coyle, A.J.; Eckert, J.; Kalia, H.

1986-07-01

This is the second joint annual report (1984) on experiments simulating a nuclear waste repository at the 800-m (2624-ft) level of the Asse salt mine in the Federal Republic of Germany. This report describes the Asse salt mine, the test equipment, and the pretest properties of the salt in the mine and in the vicinity of the test area. Also included are test data for the first 19 months of operation on the following: brine migration rates, thermal mechanical behavior of the salt (including room closure, stress reading, and thermal profiles), and borehole gas pressures. In addition to field data, laboratory analyses of results are included in this report. The duration of the experiment will be 2 years, ending in December 1985

Sensitivity and uncertainty analysis applied to a repository in rock salt

International Nuclear Information System (INIS)

Polle, A.N.

1996-12-01

This document describes the sensitivity and uncertainty analysis with UNCSAM, as applied to a repository in rock salt for the EVEREST project. UNCSAM is a dedicated software package for sensitivity and uncertainty analysis, which was already used within the preceding PROSA project. The use of UNCSAM provides a flexible interface to EMOS ECN by substituting the sampled values in the various input files to be used by EMOS ECN ; the model calculations for this repository were performed with the EMOS ECN code. Preceding the sensitivity and uncertainty analysis, a number of preparations has been carried out to facilitate EMOS ECN with the probabilistic input data. For post-processing the EMOS ECN results, the characteristic output signals were processed. For the sensitivity and uncertainty analysis with UNCSAM the stochastic input, i.e. sampled values, and the output for the various EMOS ECN runs have been analyzed. (orig.)

Shaft seals for final high-level radioactive waste repositories. ELSA. Pt. 1

International Nuclear Information System (INIS)

Kudla, W.; Schreiter, F.; Gruner, M.

2013-01-01

The state of the art in science and technology fir shaft seals with long-term stability is summarized regarding their applicability for high-level waste repository in Germany. The concepts and drafts for the shaft sealing systems ERAM, Asse, Konrad, the WIPP side, the RESEAL concept, the NAGRA concept and the project LASA are reviewed. The methodology of applying partial factors in a safety analysis is summarized and the applicability of this method for geotechnical sealing structures is confirmed. To establish geomechanical boundary conditions of the host rocks and clay stone the stress-strain behavior of the rock mass adjoining the shaft has to be identified including time-dependent thermo-mechanical processes. The general and special requirements for the design of shaft sealing systems, especially in salt rock and clay formations are described, derived from the safety requirements (BMU 2010). Finally general information needs were identified.

SRP [Salt Repository Project] configuration management plan

International Nuclear Information System (INIS)

1987-01-01

This configuration management plan describes the organization, policies, and procedures that will be used on the Salt Repository Project (SRP) to implement the configuration management disciplines and controls. Configuration management is a part of baseline management. Baseline management is defined in the SRP Baseline Procedures Notebook and also includes cost and schedule baselines. Configuration management is a discipline applying technical and administrative direction and surveillance to identify and document the functional and physical characteristics of an item, to control changes to those characteristics, to record and report change processing and implementation status, and to audit the results. Configuration management is designed as a project management tool to determine and control baselines, and ensure and document all components of a project interface both physically and functionally. The purpose is to ensure that the product acquired satisfies the project's technical and operational requirements, and that the technical requirements are clearly defined and controlled throughout the development and acquisition process. 5 figs

Site selection - siting of the final repository for spent nuclear fuel

International Nuclear Information System (INIS)

2011-03-01

SKB has selected Forsmark as the site for the final repository for spent nuclear fuel. The site selection is the end result of an extensive siting process that began in the early 1990s. The strategy and plan for the work was based on experience from investigations and development work over a period of more than ten years prior to then. This document describes the siting work and SKB's choice of site for the final repository. It also presents the information on which the choice was based and the reasons for the decisions made along the way. The document comprises Appendix PV to applications under the Nuclear Activities Act and the Environmental Code for licences to build and operate an encapsulation plant adjacent to the central interim storage facility for spent nuclear fuel in Oskarshamn, and to build and operate a final repository for spent nuclear fuel in Forsmark in Oesthammar Municipality

Site selection - siting of the final repository for spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

2011-03-15

SKB has selected Forsmark as the site for the final repository for spent nuclear fuel. The site selection is the end result of an extensive siting process that began in the early 1990s. The strategy and plan for the work was based on experience from investigations and development work over a period of more than ten years prior to then. This document describes the siting work and SKB's choice of site for the final repository. It also presents the information on which the choice was based and the reasons for the decisions made along the way. The document comprises Appendix PV to applications under the Nuclear Activities Act and the Environmental Code for licences to build and operate an encapsulation plant adjacent to the central interim storage facility for spent nuclear fuel in Oskarshamn, and to build and operate a final repository for spent nuclear fuel in Forsmark in Oesthammar Municipality

Salt Repository Project site study plan for seismographic monitoring: Revision 1

International Nuclear Information System (INIS)

1987-01-01

This site study plan describes the seismographic monitoring activities to be conducted during the early stages of Site Characterization at the Deaf Smith County site, Texas. The field programs has been designed to provide data useful in addressing information/data needs resulting from Federal/State/local regulatory requirements and repository program requirements. Sixteen new and three relocated seismographic stations will be added to the now existing network of 13 stations for a total of 32 stations in the network. The areal extent is being expanded and selected regions covered more densely to provide more accurate monitoring and location of microearthquakes. More sophisticated instruments are being used at selected locations to allow for more detailed analysis. A few seismographs are being installed at depth to provide a limited 3-D monitoring network in the area of the repository. The Salt Repository Project (SRP) Networks specify the schedule under which the program will operate. The Technique Field Services Contractor (TFSC) is responsible for conducting the field program. Data will be handled and reported in accordance with established SRP procedures. A quality assurance program will be utilized to assure that activities affecting quality are performed correctly and that appropriate documentation is maintained. 32 refs., 11 figs., 4 tabs

The thermo-mechanical behaviour of a salt dome with a heat-generating waste repository

International Nuclear Information System (INIS)

Janssen, L.G.J.; Prij, J.; Kevenaar, J.W.A.M.; Jong, C.J.T.; Klok, J.; Beemsterboer, C.

1984-01-01

This report reviews the analytical work on the disposal of radioactive waste in salt domes performed at ECN in the period 1 January 1980 to 31 December 1982. Chapter 4 in the main report covers the global temperature and deformation analyses of the salt dome and the surrounding rocks. The attached three topical reports cover self-contained parts of the study. The computer program TASTE developed to analyse, at acceptable cost and with, for engineering purposes, sufficient accuracies, the temperature rises in the salt dome due to the stored heat-generating waste is described in Annex 1. Annex 2 gives a description of the extended finite element program GOLIA. The program has been extended to make it suitable for the creep analysis of salt domes with repositories of heat-generating waste. The study on the closing and sealing of boreholes wit heat-generating waste is reported in Annex 3

Bibliography of studies for the Salt Repository Project Office of the Civilian Radioactive Waste Management Program, April 1978-May 1986

International Nuclear Information System (INIS)

1986-10-01

DOE/CH/10140-05 is an annotated bibliography of approved reports that have been produced for the US Department of Energy Salt Repository Project Office of the Civilian Radioactive Waste Management Program since April 1978. This document is intended for use by the US Department of Energy, State and local officials, the US Nuclear Regulatory Commission, contractors to the Office of Nuclear Waste Isolation, concerned citizens, and others who need a comprehensive listing of reports related to a nuclear waste repository in salt. This document consists of a main report listing, appendixes with Work Breakdown Structure lists, and a topical index

Bibliography of studies for the Salt Repository Project Office of the Civilian Radioactive Waste Management Program, April 1978-December 1986

International Nuclear Information System (INIS)

1987-06-01

This document is an annotated bibliography of approved reports that have been produced for the US Department of Energy Salt Repository Project Office of the Civilian Radioactive Waste Management Program since April 1978. This document is intended for use by the US Department of Energy, State and local officials, the US Nuclear Regulatory Commission, contractors to the Office of Nuclear Waste Isolation, concerned citizens, and others who need a comprehensive listing of reports related to a nuclear waste repository in salt. This document consists of a main report listing, appendixes with Work Breakdown Structure lists, and a topical index

Alternative methods to manage waste salt from repository excavation in the Deaf Smith County and Swisher County locations, Texas: A scoping study: Technical report

International Nuclear Information System (INIS)

1987-01-01

This report describes and qualitatively evaluates eight options for managing the large volumes of salt and salt-laden rock that would result from the excavation of a high-level radioactive waste repository in Deaf Smith County or Swisher County, Texas. The options are: distribution for commercial use; ocean disposal; deep-well injection; disposal in multilevel mines on the site; disposal in abandoned salt mines off the site; disposal off the site in abandoned mines developed for minerals other than salt; disposal in excavated landfills; and surface disposal on alkali flats. The main features of each option are described, as well as the associated environmental and economic impacts, and regulatory constraints. The options are evaluated in terms of 11 factors that jointly constitute a test of relative suitability. The results of the evaluation and implications for further study are indicated. This document does not consider or include the actual numbers, findings, or conclusions contained in the final Deaf Smith County Environmental Assessment (DOE, 1986). 43 refs., 8 tabs

National waste terminal storage repository in a bedded salt formation for spent unreprocessed fuel. Volume I. Conceptual design report

International Nuclear Information System (INIS)

1978-12-01

In February 1976, the Energy Research and Development Administration (ERDA), now the Department of Energy (DOE), established a National Waste Terminal Storage (NWTS) program. As a part of this program, two parallel conceptual design efforts were initiated in January 1977. One was for deep geologic storage, in domed salt, of high level waste resulting from the reprocessing of spent fuel. The other was for deep geologic storage of unreprocessed spent fuel in bedded salt. These two concepts are identified as NWTS Repository 1 and Repository 2, respectively. Repository 2 (NWTSR2) is the concept which is covered by this Conceptual Design Report. Volume I of the conceptual design report contains the following information: physical description of the report; project purpose and justification; principal safety, fire, and health hazards; environmental impact considerations; quality assurance considerations; assessment of operational interfaces; assessment of research and development interfaces; project schedule; proposed method of accomplishment; summary cost estimate; and outline specifications. The conceptual design for Repository 2 was developed in sufficient detail to permit determination of scope, engineering feasibility, schedule, and cost estimates, all of which are necessary for planning and budgeting the project

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

Energy Technology Data Exchange (ETDEWEB)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-11-15

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

International Nuclear Information System (INIS)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-01-01

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Effects of temperature, temperature gradients, stress, and irradiation on migration of brine inclusions in a salt repository

International Nuclear Information System (INIS)

Jenks, G.H.

1979-07-01

Available experimental and theoretical information on brine migration in bedded salt are reviewed and analyzed. The effects of temperature, thermal gradients, stress, irradiation, and pressure in a salt repository are among the factors considered. The theoretical and experimental (with KCl) results of Anthony and Cline were used to correlate and explain the available data for rates of brine migration at temperatures up to 250 0 C in naturally occurring crystals of bedded salt from Lyons and Hutchinson, Kansas. Considerations of the effects of stressing crystals of bedded salt on the migratin properties of brine inclusions within the crystals led to the conclusion that the most probable effects are a small fractional increase in the solubility of the salt within the liquid and a concomitant and equal fractional increase in the rate of the thermal gradient-induced migration of the brine. The greatest uncertainty relative to the prediction of rates of migration of brine into a waste emplacement cavity in bedded salt is associated with questions concerning the effects of the grain boundaries (within the aggregates of single crystals which comprise a bedded salt deposit) on brine migration through the deposit. The results of some of the estimates of rates and total amounts of brine inflow to HLW and SURF waste packages emplaced in bedded salt were included to illustrate the inflow volumes which might occur in a repository. The results of the brine inflow estimates for 10-year-old HLW emplaced at 150 kW/acre indicated inflow rates starting at 0.7 liter/year and totaling 12 liters at 30 years after emplacement. The results of the estimates for 10-year-old PWR SURF emplaced at 60 kW/acre indicated a constant inflow of 0.035 liter/year for the first 35 years after emplacement

Design principle of TVO's final repository and preliminary adaptation to site specific conditions

International Nuclear Information System (INIS)

Salo, J-P.; Reikkola, R.

1995-01-01

Teollisuuden Voima Oy (TVO) is responsible for the management of spent fuel produced by the Olkiluoto power plant. TVO's current programme of spent fuel management is based on the guidelines and time schedule set by the Finnish Government. TVO has studied a final disposal concept in which the spent fuel bundles are encapsulated in copper canisters and emplaced in Finnish bedrock. According to the plan the final repository for spent fuel will be in operation by 2020. TVO's updated technical plans for the disposal of spent fuel together with a performance analysis (TVO-92) were submitted to the authorities in 1992. The paper describes the design principle of TVO's final repository and preliminary adaptation of the repository to site specific conditions. (author). 10 refs., 5 figs

Identification of release scenarios for a repository of radioactive waste in a salt dome in the Netherlands

International Nuclear Information System (INIS)

Glasbergen, P.; Hamstra, J.

1981-01-01

A review is presented of the long-term scenarios used in the safety analysis which was carried out for the disposal of radioactive waste in salt domes in the Netherlands. The long-term analysis involved the following natural processes or events: climatological and sea-level changes, glacial erosion, diapirism, subsidence, faulting and dissolution. The model calculations which were carried out showed the dominant parameters: the rate of diapirism and the rate of subsurface dissolution of rock salt. During the operational period the intrusion of water in the repository was considered to be the most hazardous event. Because the layout of the disposal mine, the disposal geometry and the disposal mining procedures were still under consideration, the first approach of a release scenario was made on a generic basis. A generic scenario is presented for the events during the flooding of the repository. The transport ways of water through the repository and its surroundings are indicated. It is concluded that release scenario analysis for long-term periods and for the operational period provides essential information to optimize the overall disposal system in an iterative process

Design and construction issues associated with sealing of a repository in salt

International Nuclear Information System (INIS)

Cook, R.

1991-01-01

The isolation of radioactive wastes in geologic repositories requires that man-made penetrations such as shafts, tunnels and boreholes are adequately sealed. This paper presents the current design and construction issues for sealing a repository in salt and outlines some proposed solutions. The sealing components include shaft seals, tunnel seals, panel seals, and disposal room backfill. The performance requirements and construction constraints determine the types of materials selected and their necessary properties. The current issues of interest include: (1) selection of materials for rigid bulkheads used to promote recovery of the disturbed zone permeability; (2) the selection of bulkhead geometry to cutoff flow through more permeable zones, or zones where recovery of the backfill properties occurs more slowly or not at all; and (3) the interaction of fluids with hazardous wastes with brine and, subsequently, with seal materials that might affect seal material longevity. 19 refs., 5 figs., 1 tab

GRS/ISTec strategy for the treatment of gas-related issues for repositories located in rock salt

International Nuclear Information System (INIS)

Muller-Lyda, I.; Javeri, V.; Muller, W.

2001-01-01

The treatment of gas-related issues for repositories located in rock salt by GRS and ISTec has followed a strategy which has been developed with increasing complexity and degree of detail in the past. The strategy today clearly indicates the direction to establish a comprehensive safety case and the work that remains to be done. For gas generation mainly long-term aspects are an issue to increase accuracy of predictions. Physical modelling especially for HLW is still incomplete with regard to the coupling of fluid flow with geomechanics, solution/precipitation effects and geochemistry. The appropriate tools to transform the physical models into numerical solutions are at hand in principle but have to be further developed collaterally to the physical modelling. The first full-scale demonstration of safety regarding gas issues in rock salt will have to be provided for the licensing of the Morsleben repository shut-down in the near future. (authors)

Model-based studies into ground water movement, with water density depending on salt content. Case studies and model validation with respect to the long-term safety of radwaste repositories. Final report

International Nuclear Information System (INIS)

Schelkes, K.

1995-12-01

Near-to-reality studies into ground water movement in the environment of planned radwaste repositories have to take into account that the flow conditions are influenced by the water density which in turn depends on the salt content. Based on results from earlier studies, computer programs were established that allow computation and modelling of ground water movement in salt water/fresh water systems, and the programs were tested and improved according to progress of the studies performed under the INTRAVAL international project. The computed models of ground water movement in the region of the Gorlebener Rinne showed for strongly simplified model profiles that the developing salinity distribution varies very sensitively in response to the applied model geometry, initial input data for salinity distribution, time frame of the model, and size of the transversal dispersion length. The WIPP 2 INTRAVAL experiment likewise studied a large-area ground water movement system influenced by salt water. Based on the concept of a hydraulically closed, regional ground water system (basin model), a sectional profile was worked out covering all relevant layers of the cap rock above the salt formation planned to serve as a repository. The model data derived to describe the salt water/fresh water movements in this profile resulted in essential enlargements and modifications of the ROCKFLOW computer program applied, (relating to input data for dispersion modelling, particle-tracker, computer graphics interface), and yielded important information for the modelling of such systems (relating to initial pressure data at the upper margin, network enhancement for important concentration boundary conditions, or treatment of permeability contrasts). (orig.) [de

Design of repository sealing systems - 1981

International Nuclear Information System (INIS)

Ellison, R.D.; Shukla, D.K.; Kelsall, P.C.; D'Appolonia Consulting Engineers, Albuquerque, NM)

1982-01-01

Isolating nuclear waste in geologic repositories will require the sealing of penetrations such as access shafts and tunnels, disposal rooms, and exploration boreholes. This paper discusses seal designs developed for a repository in bedded salt referenced to the stratigraphy of southeastern New Mexico. Designs are based on a multiple component concept whereby individual components are designed for a specific function and location. For a repository in salt the major function of the seals is to exclude groundwater inflow. Two main types of component are included for this purpose: (1) bulk-heads are dense concrete structures keyed into the walls of the penetration and are intended to reduce flow at the interface between the seal and the salt; (2) backfills are granular materials compacted in place in the penetration. In the repository the major backfill material is crushed salt, which is expected to consolidate and recrystallize as the rooms close in response to salt creep. Densely compacted clays will be used as backfill in the shafts closer to potential sources of water inflow. 22 references, 10 figures, 1 table

Radioactive waste isolation in salt: Peer review of the Fluor Technology, Inc., report and position paper concerning waste emplacement mode and its effect on repository conceptual design

International Nuclear Information System (INIS)

Hambley, D.F.; Russell, J.E.; Whitfield, R.G.

1987-02-01

Recommendations for revising the Fluor Technology, Inc., draft position paper entitled Evaluation of Waste Emplacement Mode and the final report entitled Waste Package/Repository Impact Study include: reevaluate the relative rankings for the various emplacement modes; delete the following want objectives: maximize ability to locate the package horizon because sufficient flexibility exists to locate rooms in the relatively clean San Andres Unit 4 Salt and maximize far-field geologic integrity during retrieval because by definition the far field will be unaffected by thermal and stress perturbations caused by remining; give greater emphasis to want objectives regarding cost and use of present technology; delete the following statements from pages 1-1 and 1-2 of the draft position paper: ''No thought or study was given to the impacts of this configuration [vertical emplacement] on repository construction or short and long-term performance of the site'' and ''Subsequent salt repository designs adopted the vertical emplacement configuration as the accepted method without further evaluation.''; delete App. E and lines 8-17 of page 1-4 of the draft position paper because they are inappropriate; adopt a formal decision-analysis procedure for the 17 identified emplacement modes; revise App. F of the impact study to more accurately reflect current technology; consider designing the underground layout to take advantage of stress-relief techniques; consider eliminating reference to fuel assemblies <10 yr ''out-of-reactor''; model the temperature distribution, assuming that the repository is constructed in an infinitely large salt body; state that the results of creep analyses must be considered tentative until they can be validated by in situ measurements; and reevaluate the peak radial stresses on the waste package so that the calculated stress conditions more closely approximate expected in situ conditions

Proceedings of the 5th US/German Workshop on Salt Repository Research Design and Operation

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Leigh, Christi [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stein, Walter [Karlsruhe Inst. of Technology (KIT) (Germany); Bollingerfehr, Wilhelm [DBE Technology, Peine (Germany); Von Berlepsche, Thilo [DBE Technology, Peine (Germany)

2015-01-01

The 5th US/German Workshop on Salt Repository Research, Design, and Operation was held in Santa Fe New Mexico September 8-10, 2014. The forty seven registered participants were equally divided between the United States (US) and Germany, with one participant from The Netherlands. The agenda for the 2014 workshop was under development immediately upon finishing the 4th Workshop. Ongoing, fundamental topics such as thermomechanical behavior of salt, plugging and sealing, the safety case, and performance assessment continue to advance the basis for disposal of heat-generating nuclear waste in salt formations. The utility of a salt underground research laboratory (URL) remains an intriguing concept engendering discussion of testing protocol. By far the most interest in this years’ workshop pertained to operational safety. Given events at the Waste Isolation Pilot Plant (WIPP), this discussion took on a new sense of relevance and urgency.

Groundwater recharge and discharge scenarios for a nuclear waste repository in bedded salt

International Nuclear Information System (INIS)

Carpenter, D.W.; Steinborn, T.L.; Thorson, L.D.

1979-01-01

Twelve potential scenarios have been identified whereby groundwater may enter or exit a nuclear waste repository in bedded salt. The 12 scenarios may be grouped into 4 categories or failure modes: dissolution, fracturing, voids, and penetration. Dissolution modes include breccia pipe and breccia blanket formation, and dissolution around boreholes. Fracture modes include flow through preexisting or new fractures and the effects of facies changes. Voids include interstitial voids (pores) and fluid inclusions. Penetration modes include shaft and borehole sealing failures, undetected boreholes, and new mines or wells constructed after repository decommissioning. The potential importance of thermal effects on groundwater flow patterns and on the recharge-discharge process is discussed. The appropriate levels of modeling effort, and the interaction between the adequacy of the geohydrologic data base and the warranted degree of model complexity are also discussed

Radioactive waste isolation in salt: special advisory report on the status of the Office of Nuclear Waste Isolation's plans for repository performance assessment

International Nuclear Information System (INIS)

Ditmars, J.D.; Walbridge, E.W.; Rote, D.M.; Harrison, W.; Herzenberg, C.L.

1983-10-01

Repository performance assessment is analysis that identifies events and processes that might affect a repository system for isolation of radioactive waste, examines their effects on barriers to waste migration, and estimates the probabilities of their occurrence and their consequences. In 1983 Battelle Memorial Institute's Office of Nuclear Waste Isolation (ONWI) prepared two plans - one for performance assessment for a waste repository in salt and one for verification and validation of performance assessment technology. At the request of the US Department of Energy's Salt Repository Project Office (SRPO), Argonne National Laboratory reviewed those plans and prepared this report to advise SRPO of specific areas where ONWI's plans for performance assessment might be improved. This report presents a framework for repository performance assessment that clearly identifies the relationships among the disposal problems, the processes underlying the problems, the tools for assessment (computer codes), and the data. In particular, the relationships among important processes and 26 model codes available to ONWI are indicated. A common suggestion for computer code verification and validation is the need for specific and unambiguous documentation of the results of performance assessment activities. A major portion of this report consists of status summaries of 27 model codes indicated as potentially useful by ONWI. The code summaries focus on three main areas: (1) the code's purpose, capabilities, and limitations; (2) status of the elements of documentation and review essential for code verification and validation; and (3) proposed application of the code for performance assessment of salt repository systems. 15 references, 6 figures, 4 tables

High level nuclear waste repository in salt: Sealing systems status and planning report: Draft report

International Nuclear Information System (INIS)

1985-09-01

This report documents the initial conceptual design studies for a repository sealing system for a high-level nuclear waste repository in salt. The first step in the initial design studies was to review the current design level, termed schematic designs. This review identified practicality of construction and development of a design methodology as two key issues for the conceptual design. These two issues were then investigated during the initial design studies for seal system materials, seal placement, backfill emplacement, and a testing and monitoring plan. The results of these studies have been used to develop a program plan for completion of the sealing system conceptual design. 60 refs., 26 figs., 18 tabs

Final Report: Improving the understanding of the coupled thermal-mechanical-hydrologic behavior of consolidating granular salt

Energy Technology Data Exchange (ETDEWEB)

Stormont, John [Univ. of New Mexico, Albuquerque, NM (United States); Lampe, Brandon [Univ. of New Mexico, Albuquerque, NM (United States); Mills, Melissa [Univ. of New Mexico, Albuquerque, NM (United States); Paneru, Laxmi [Univ. of New Mexico, Albuquerque, NM (United States); Lynn, Timothy [Univ. of New Mexico, Albuquerque, NM (United States); Piya, Aayush [Univ. of New Mexico, Albuquerque, NM (United States)

2017-09-09

The goal of this project is to improve the understanding of key aspects of the coupled thermal-mechanical-hydrologic response of granular (or crushed) salt used as a seal material for shafts, drifts, and boreholes in mined repositories in salt. The project is organized into three tasks to accomplish this goal: laboratory measurements of granular salt consolidation (Task 1), microstructural observations on consolidated samples (Task 2), and constitutive model development and evaluation (Task 3). Task 1 involves laboratory measurements of salt consolidation along with thermal properties and permeability measurements conducted under a range of temperatures and stresses expected for potential mined repositories in salt. Testing focused on the role of moisture, temperature and stress state on the hydrologic (permeability) and thermal properties of consolidating granular salt at high fractional densities. Task 2 consists of microstructural observations made on samples after they have been consolidated to interpret deformation mechanisms and evaluate the ability of the constitutive model to predict operative mechanisms under different conditions. Task 3 concerns the development of the coupled thermal-mechanical-hydrologic constitutive model for granular salt consolidation. The measurements and observations in Tasks 1 and 2 were used to develop a thermal-mechanical constitutive model. Accomplishments and status from each of these efforts is reported in subsequent sections of this report

Final repository search together with the citizens. Information, consultation, dialogue, participation; Endlagersuche - gemeinsam mit den Buergern. Information, Konsultation, Dialog, Beteiligung

Energy Technology Data Exchange (ETDEWEB)

Mueller, Monika C.M. (ed.)

2013-07-01

The documentation on the Loccum meeting 2013 includes contributions on the following topics: Public participation for the final repository search; Lessons learned from the past; Public participation: what is expected? Experiences of repository operators on public participation; The TRIPLEX concept; From Gorleben to the law on final repository search: a long and a short story; Public participation concerning radioactive waste storage; The public has to be informed on the radioactive waste problem and the possible solutions; After consensus is before consensus - German final repository conflict between legislation and simulated public participation; Political concept of public participation; A fast final repository law will not bring about social peace; Good public participation on final repository search - requirements, challenges, questions and approaches.

Project ANSICHT. Final repository concept and backfilling and sealing concept for the final repository site model SUeD; Projekt ANSICHT. Endlagerkonzept sowie Verfuell- und Verschlusskonzept fuer das Endlagerstandortmodell SUeD. Technischer Bericht

Energy Technology Data Exchange (ETDEWEB)

Jobmann, Michael; Lommerzheim, Andree

2015-08-03

In the frame of ANSICHT the methodology for the demonstration of safe enclosure for high-level heat generating radioactive wastes is described. The report is based on the safety requirements for final repository concepts and shows a first backfilling and sealing concept that was developed for the final repository site model SUeD. The final repository model SUeD is based on a horizontal line storage concept, the Gorleben (VSG) and ERATO container concept and the mine layout were adopted and adapted to the given conditions. The backfill and sealing concept includes migration barriers, line closures and shaft closures in the frame of a redundant and diverse enclosure system. For all technical and geotechnical barrier components the long-term functional requirements were defined. The backfilling concept of underground cavities considers the variety of possible cavities in the line and infrastructure areas.

A comparison of risks due to HLW and SURF repositories in bedded salt

International Nuclear Information System (INIS)

Chu, M.S.Y.; Ortiz, N.R.; Wahi, K.K.

1983-01-01

A methodology was developed to analyze risks from geologic disposal of nuclear wastes. It was applied to estimate the risk due to spent fuel and high-level waste hypothetical repositories in bedded salt. A number of disruptive scenarios were analyzed for each waste type. A comparison between the spent fuel and high-level waste results is presented. The methodology enables one to identify important radionuclides, parameters, and scenarios in terms of their relative contribution to the overall risk or compliance with the proposed EPA Standard

Report on materials characterization center workshop on stress corrosion cracking for the Salt Repository Project, December 16-17, 1986, Seattle, Washington: Workshop summary

International Nuclear Information System (INIS)

Merz, M.D.; Shannon, D.W.

1986-09-01

The Materials Characterization Center (MCC) at Pacific Northwest Laboratory (PNL) conducted a Workshop on Stress Corrosion Cracking for the Salt Repository Project on December 16 and 17, 1986 in Seattle, Washington. The workshop was held to formulate recommendations for addressing stress corrosion cracking (SCC) in a salt repository. It was attended by 24 representatives from major laboratories, universities, and industry. This report presents the recommendations of the workshop, along with the agenda, list of participants, questions and comments, summaries of working groups on low-strength steel and alternate materials, and materials handed out by the speakers

Waste package materials testing for a salt repository: 1983 status summary report

International Nuclear Information System (INIS)

Moak, D.P.

1986-09-01

The United States plans to safely dispose of nuclear waste in deep, stable geologic formations. As part of these plans, the US Department of Energy is sponsoring research on the designing and testing of waste packages and waste package materials. This fiscal year 1983 status report summarizes recent results of waste package materials testing in a salt environment. The results from these tests will be used by waste package designers and performance assessment experts. Release characteristics data are available on two waste forms (spent fuel and waste-containing glass) that were exposed to leaching tests at various radiation levels, temperatures, pH, glass surface area to solution volume ratios, and brine solutions simulating expected salt repository conditions. Candidate materials tested for corrosion resistance and other properties include iron alloys; TI-CODE 12, the most promising titanium alloy for containment; and nickel alloys. In component interaction testing, synergistic effects have not ruled out any candidate material. 21 refs., 37 figs., 15 tabs

New developments in measurement technology relevant to the studies of deep geological repositories in domed salt and basalt

International Nuclear Information System (INIS)

Ramirez, A.L.; Mao, N.H.

1980-01-01

This report briefly describes recent geophysical and geotechnical instrumentation developments relevant to the studies of deep geologic repositories. Special emphasis has been placed on techniques that appear to minimize measurement problems associated with repositories constructed in basalt or domed salt. Included in the listing are existing measurement capabilities and deficiencies that have been identified by a few authors and instrumentation workshops that have assessed the capabilities of existing instrumentation with respect to repository applications. These deficiencies have been compared with the reported advantages and limitations of the new developments described. Based on these comparisons, areas that merit further research and development have been identified. The report is based on a thorough literature review and on discussions with several instrumentation specialists involved in instrumentation development

Generic aspects of salt repositories

International Nuclear Information System (INIS)

Laughon, R.B.

1979-01-01

The history of geological disposal of radioactive wastes in salt is presented from 1957 when a panel of the National Academy of Sciences-National Research Council recommended burial in bedded salt deposits. Early work began in the Kansas, portion of the Permian Basin where simulated wastes were placed in an abandoned salt mine at Lyons, Kansas, in the late 1960's. This project was terminated when the potential effect of nearby solution mining activities could not be resolved. Evaluation of bedded salts resumed a few years later in the Permian Basin in southeastern New Mexico, and search for suitable sites in the 1970's resulted in the formation of the National Waste Terminal Storage Program in 1976. Evaluation of salt deposits in many regions of the United States has been virtually completed and has shown that deposits having the greatest potential for radioactive waste disposal are those of the largest depositional basins and salt domes of the Gulf Coast region

Preliminary petrological and geochemical results from the Salton Sea Geothermal Field, California: A near-field natural analog of a radioactive waste repository in salt: Topical report No. 2

International Nuclear Information System (INIS)

Elders, W.A.; Cohen, L.H.; Williams, A.E.; Neville, S.; Collier, P.; Oakes, C.

1986-03-01

High concentrations of radionuclides and high temperatures are not naturally encountered in salt beds. For this reason, the Salton Sea Geothermal Field (SSGF) may be the best available geologic analog of some of the processes expected to occur in high level nuclear waste repositories in salt. Subsurface temperatures and brine concentrations in the SSGF span most of the temperature range and fluid inclusion brine range expected in a salt repository, and the clay-rich sedimentary rocks are similar to those which host bedded or domal salts. As many of the chemical processes observed in the SSGF are similar to those expected to occur in or near a salt repository, data derived from it can be used in the validation of geochemical models of the near-field of a repository in salt. This report describes preliminary data on petrology and geochemistry, emphasizing the distribution of rare earth elements and U and Th, of cores and cuttings from several deep wells chosen to span a range of temperature gradients and salinities. Subsurface temperature logs have been augmented by fluid inclusion studies, to reveal the effects of brines of varying temperature and salinity. The presence of brines with different oxygen isotopic signatures also indicate lack of mixing. Whole rock major, minor and trace element analyses and data on brine compositions are being used to study chemical migration in these sediments. 65 refs., 20 figs., 3 tabs

Judicial progress in Germany's nuclear waste disposal policy the Konrad repository decisions of 26 march 2007

International Nuclear Information System (INIS)

Kuhne, G.

2007-01-01

Its exists three final repository sites in Germany, an overview of the status of these sites is necessary to understand concretely the situation. Morsleben, is actually the only final repository for low and medium level radioactive waste. Gorleben is the site of a salt dome which is under exploration as an eventual repository for high level radioactive waste but the study is under a decree of exploration moratorium of at least three years, in order to allow for investigation into conceptual and safety issues. The Konrad ore mine is the site under preparation for a final repository for low and medium level radioactive waste. The present article will briefly address three aspects of the court reasoning: the legal character of the plan approval notice (act of discretion or strict execution of laws), the necessity of planning and safety aspects. (N.C.)

Efficacy of backfilling and other engineered barriers in a radioactive waste repository in salt

International Nuclear Information System (INIS)

Claiborne, H.C.

1982-09-01

In the United States, investigation of potential host geologic formations was expanded in 1975 to include hard rocks. Potential groundwater intrusion is leading to very conservative and expensive waste package designs. Recent studies have concluded that incentives for engineered barriers and 1000-year canisters probably do not exist for reasonable breach scenarios. The assumption that multibarriers will significantly increase the safety margin is also questioned. Use of a bentonite backfill for surrounding a canister of exotic materials was developed in Sweden and is being considered in the US. The expectation that bentonite will remain essentially unchanged for hundreds of years for US repository designs may be unrealistic. In addition, thick bentonite backfills will increase the canister surface temperature and add much more water around the canister. The use of desiccant materials, such as CaO or MgO, for backfilling seems to be a better method of protecting the canister. An argument can also be made for not using backfill material in salt repositories since the 30-cm-thick space will provide for hole closure for many years and will promote heat transfer via natural convection. It is concluded that expensive safety systems are being considered for repository designs that do not necessarily increase the safety margin. It is recommended that the safety systems for waste repositories in different geologic media be addressed individually and that cost-benefit analyses be performed

Constitutive parameters for salt and nonsalt rocks from the Detten, G. Friemel, and Zeeck wells in the Palo Duro Basin, Texas

International Nuclear Information System (INIS)

Senseny, P.E.; Pfeifle, T.W.; Mellegard, K.D.

1985-01-01

Results are presented from laboratory tests performed on salt and nonsalt rocks from the Palo Duro Basin in Texas. The Unit 5 salt from the Lower San Andres is assumed to be the repository horizon and is more completely characterized than other strata. For the Unit 5 salt, values are given for the parameters in the exponential-time constitutive law that models the time-independent elastic deformation and the time-dependent inelastic deformation. Both linear and nonlinear failure envelopes for this salt at 20 0 C are also determined. Data reported for twenty other salt and nonsalt horizons include tangent moduli and principal strain ratios, as well as linear failure envelopes at 20 0 C. The matrix of tests performed is adequate for conceptual repository design and performance analysis. However, final repository design and performance analysis requires more extensive characterization of the constitutive behavior of the stratigraphy, especially the repository-horizon salt

Schematic designs for penetration seals for a repository in the Paradox Basin

International Nuclear Information System (INIS)

Kelsall, P.C.; Meyer, D.; Case, J.B.; Coons, W.E.

1985-12-01

The isolation of radioactive wastes in geologic repositories requires that human-made penetrations such as shafts, tunnels, or boreholes are adequately sealed. This report describes schematic seal designs for a repository in bedded salt referenced to the stratigraphy of the Paradox Basin. The designs are presented for extensive peer review and will be updated as conceptual designs if the Paraodx Basin is selected as a candidate repository site. The principal components used in the shaft seal system are concrete bulkheads interspersed with highly compacted bentonite-rich earth fill. In the repository-level tunnels and rooms, the principal material used in the seal system is crushed salt obtained from excavating the repository. It is anticipated that crushed salt will consolidate in response to closure of the repository rooms, to the degree that mechanical and hydrologic properties will eventually match those of undisturbed, intact salt. For Paradox Basin Cycle 6 salt, analyses indictate that this process will require approximately 300 years for a seal located at the base of one of the repository shafts (where there is little increase in temperature due to waste emplacement) and approximately 140 years for a seal located in a main passageway within the repository. These analyses are based on uncertain laboratory data regarding intact salt creep rates and crushed salt consolidation characteristics, and must be regarded as preliminary

Salt Repository Project: Waste Package Program (WPP) modeling activiteis: FY 1984 annual report

International Nuclear Information System (INIS)

Kuhn, W.L.; Simonson, S.A.; Pulsipher, B.A.

1987-03-01

The Pacific Northwest Laboratory (PNL) is supporting the US Department of Energy's (DOE) Salt Repository Project (SRP) through its Waste Package Program (WPP). During FY 1984, the WPP continued its program of waste package component development and interactions testing and application of the resulting data base to develop predictive models describing waste package degradation and radionuclide release. Within the WPP, the Modeling Task (Task 04 during FY 1984) was conducted to interpret the tests in such a way that scientifically defensible models can be developed for use in qualification of the waste package

Final draft position on geotechnical instrumentation in a salt repository environment: Requirements, performance, recommendations, and development needs

International Nuclear Information System (INIS)

1987-07-01

This report presents the results of a study of the present status of geotechnical instrumentation with respect to potential use in an underground test facility at a candidate nuclear waste repository site in salt. Programmatic factors that have a general impact on the success of underground instrumentation are discussed. Performance requirements relating to accuracy, temperature range, longevity, and capability for automation are established on the basis of criteria proposed for other rock types, perceived needs of the Site Characterization Program, and the authors' experience and judgment. Test site conditions are discussed including underground logistics, corrosion, and other factors that affect instrument reliability. The status of existing instrumentation for measuring deformation, stress, temperature, fluid pressure, acoustic emission, and other less critical parameters is presented. For each instrument not presently capable of satisfying its associated performance requirements, specific development needs and possible approaches are identified, and necessary testing is describe to a conceptual level of detail. A brief discussion of instrument considerations relating to automatic data acquisition is also included. The position of instrument development as a key activity on the critical path under current schedules for the Site Characterization Program is discussed. Annotated references and reports on site visits and meetings used as the data base in evaluating present instrument status are appended to this report. 110 refs., 14 figs., 26 tabs

Salt disposal: Paradox Basin, Utah

International Nuclear Information System (INIS)

1983-04-01

This report presents the findings of a study conducted for the National Waste Terminal Storage (NWTS) Program. Permanent disposal options are examined for salt resulting from the excavation of a waste repository in the bedded salt deposits of the Paradox Basin of southeastern Utah. The study is based on a repository salt backfill compaction of 60% of the original density which leaves a total of 8 million tons of 95% pure salt to be disposed of over a 30-year period. The feasibility, impacts, and mitigation methods are examined for five options: commercial disposal, permanent onsite surface disposal, permanent offsite disposal, deepwell injection, and ocean and Great Salt Lake disposal. The study concludes the following: Commercial marketing of all repository salt would require a subsidy for transportation to major salt markets. Permanent onsite surface storage is both economically and technically feasible. Permanent offsite disposal is technically feasible but would incur additional transportation costs. Selection of an offsite location would provide a means of mitigating impacts associated with surface storage at the repository site. Deepwell injection is an attractive disposal method; however, the large water requirement, high cost of development, and poor performance of similar operating brine disposal wells eliminates this option from consideration as the primary means of disposal for the Paradox Basin. Ocean disposal is expensive because of high transportation cost. Also, regulatory approval is unlikely. Ocean disposal should be eliminated from further consideration in the Paradox Basin. Great Salt Lake disposal appears to be technically feasible. Great Salt Lake disposal would require state approval and would incur substantial costs for salt transportation. Permanent onsite disposal is the least expensive method for disposal of all repository salt

Final report on uncertainties in the detection, measurement, and analysis of selected features pertinent to deep geologic repositories

International Nuclear Information System (INIS)

1978-01-01

Uncertainties with regard to many facets of repository site characterization have not yet been quantified. This report summarizes the state of knowledge of uncertainties in the measurement of porosity, hydraulic conductivity, and hydraulic gradient; uncertainties associated with various geophysical field techniques; and uncertainties associated with the effects of exploration and exploitation activities in bedded salt basins. The potential for seepage through a depository in bedded salt or shale is reviewed and, based upon the available data, generic values for the hydraulic conductivity and porosity of bedded salt and shale are proposed

Thermoelastic analyses of spent fuel repositories in bedded and dome salt. Technical memorandum report RSI-0054

International Nuclear Information System (INIS)

Callahan, G.D.; Ratigan, J.L.

1978-01-01

Global thermoelastic analyses of bedded and dome salt models showed a slight preference for the bedded salt model through the range of thermal loading conditions. Spent fuel thermal loadings should be less than 75 kW/acre of the repository pending more accurate material modeling. One should first limit the study to one or two spent fuel thermal loading (i.e. 75 kW/acre and/or 50 kW/acre) analyses up to a maximum time of approximately 2000 years. Parametric thermoelastic type analyses could then be readily obtained to determine the influence of the thermomechanical properties. Recommendations for further study include parametric analyses, plasticity analyses, consideration of the material interfaces as joints, and possibly consideration of a global joint pattern (i.e. jointed at the same orientation everywhere) for the non-salt materials. Subsequently, the viscoelastic analyses could be performed

Analysis of corrosion data for carbon steels in simulated salt repository brines and acid chloride solutions at high temperatures

International Nuclear Information System (INIS)

Diercks, D.R.; Hull, A.B.; Kassner, T.F.

1988-03-01

Carbon steel is currently the leading candidate material for fabrication of a container for isolation of high level nuclear waste in a salt repository. Since brine entrapped in the bedded salt can migrate to the container by several transport processes, corrosion is an important consideration in the long-term performance of the waste package. A detailed literature search was performed to compile relevant corrosion data for carbon steels in anoxic acid chloride solutions, and simulated salt repository brines at temperatures between ∼ 20 and 400 0 C. The hydrolysis of Mg 2+ ions in simulated repository brines containing high magnesium concentrations causes acidification at temperatures above 25 0 C, which, in turn, influences the protective nature of the magnetite corrosion product layer on carbon steel. The corrosion data for the steels were analyzed, and an analytical model for general corrosion was developed to calculate the amount of penetration (i.e., wall thinning) as a function of time, temperature, and the pressure of corrosion product hydrogen than can build up during exposure in a closed system (e.g., a sealed capsule). Both the temperature and pressure dependence of the corrosion rate of steels in anoxic acid chloride solutions indicate that the rate-controlling partial reaction is the cathodic reduction of water to form hydrogen. Variations in the composition and microstructure of the steels or the concentration of the ionic species in the chloride solutions (provided that they do not change the pH significantly) do not appear to strongly influence the corrosion rate

Salt Repository Project site study plan for background environmental radioactivity: Revision 1

International Nuclear Information System (INIS)

1987-12-01

The Site Study Plan for Background Environmental Radioactivity describes a field program consisting of an initial radiological survey and a radiological sampling program. The field program includes measurement of direct radiation and collection and analysis of background radioactivity samples of air, precipitation, soil, water, milk, pasture grass, food crops, meat, poultry, game, and eggs. The plan describes for each study the need for the study, the study design, data management, and use, schedule of proposed activities, and quality assurance requirements. These studies will provide data needed to satisfy requirements contained in, or derived from, the Salt Repository Project Requirements Document. 43 refs., 10 figs., 7 tabs

Accumulated energy determination in salts rocks irradiated by means of thermoluminescence techniques: application to the high level radioactive wastes repositories analysis

International Nuclear Information System (INIS)

Dies, J.; Ortega. J.; Tarrasa. F.; Cuevas, C.

1995-01-01

The report summarizes the study carried out to develop the radiation effects on salt rocks in order to repository the high level radioactive wastes. The study is structured into 3 main aspects: 1.- Analysis of irradiation experiences in Haw project of Pet ten reactor. 2.- Irradiation of salt sample of CESAR industrial irradiator. 3.- Correlation study between the accumulated energy, termoluminescence answer and the defect concentration

Thermomechanical behaviour of salt rock. Project part 1

International Nuclear Information System (INIS)

Albrecht, H.; Hunsche, U.; Diekmann, N.; Ludwig, R.

1991-08-01

The present final report on the research project KWA 58019, part I, gives an overview of the research done from early in 1988 till mid-1991 in section B 2.13 of the Federal Office of Geosciences and Raw Materials, in the field of salt mechanics. This report contributes to the scientific foundations for dimensioning and safety analysis of a repository for radioactive wastes in a salt dome and for underground exploration of a salt dome. It covers the activities financed both by the research project and by earmarked funds. (orig.) [de

Remaining porosity and permeability of compacted crushed rock salt backfill in a HLW repository. Final report

Energy Technology Data Exchange (ETDEWEB)

Jobmann, M.; Mueller, C.; Schirmer, S.

2015-11-15

The safe containment of radioactive waste is to be ensured by the geotechnical barriers in combination with the containment-providing rock zone (CRZ). The latter is a key element of the recently developed concept of demonstrating the integrity of the geologic barrier (Krone et al., 2013). As stipulated in the safety requirements of the regulating body the CRZ has to have strong barrier properties, and evidence needs to be provided that it retains its integrity throughout the reference period (BMU, 2010). The underground openings excavated in the rock salt will close over time due to the creep properties of the rock salt. This process causes deformations in the surrounding rock salt, which leads to a change in stress state in the virgin rock and may impair the integrity of the containment-providing rock zone. In order to limit the effects of these processes, all underground openings will be backfilled with crushed salt. Immediately after backfilling, the crushed salt will have an initial porosity of approx. 35%, which - over time - will be reduced to very low values due to the creep properties of the rock salt. The supporting pressure that builds up in the crushed salt with increasing compaction slows down the creeping of the salt. Major influencing factors are the temperature (with higher temperatures accelerating the salt creeping) and the moisture of the salt, which - due to the related decrease in the resistance of the crushed salt - facilitates its compaction. The phenomenology of these processes and dependencies is understood to a wide extent. This project investigated the duration until compaction is completed and when and under what circumstances the crushed salt will have the sealing properties necessary to ensure safe containment. Thermo-hydro-mechanical (THM) processes play a crucial role in determining whether solutions which might enter the mine could reach the radioactive waste. This includes changes in material behaviour due to a partial or complete

Mined salt storage feasibility: Engineering study report

International Nuclear Information System (INIS)

1987-07-01

This study addresses a method of eliminating the surface storage of mined salt at the Deaf Smith repository site. It provides rough estimates of the logistics and costs of transporting 3.7 million tons of salt from the repository to the salt disposal site near Carlsbad, New Mexico and returning it to the repository for decommissioning backfill. The study assumes that a railcar/truck system will be installed and that the excavated salt will be transported from the repository to an existing potash mine located near Carlsbad, New Mexico approximately 300 miles from the repository. The 3.7 million tons of salt required for repository decommissioning backfill can be stored in the potash mines along with the excess salt, with no additional capital costs required for either a railcar or a truck transportation system. The capital cost for facilities to reclaim the 3.7 million tons of salt from the potash mine is estimated to be $4,400,000 with either a rail or truck transportation system. Segregating the 3.7 million tons of backfill salt in a surface storage area at the potash mine requires a capital cost of $13,900,000 with a rail system or $11,400,000 with a truck system. Transportation costs are estimated at $0.08/ton-mile for rail and $0.13/ton-mile for truck. 2 figs., 5 tabs

Reconsolidated Salt as a Geotechnical Barrier

International Nuclear Information System (INIS)

Hansen, Francis D.; Gadbury, Casey

2015-01-01

Salt as a geologic medium has several attributes favorable to long-term isolation of waste placed in mined openings. Salt formations are largely impermeable and induced fractures heal as stress returns to equilibrium. Permanent isolation also depends upon the ability to construct geotechnical barriers that achieve nearly the same high-performance characteristics attributed to the native salt formation. Salt repository seal concepts often include elements of reconstituted granular salt. As a specific case in point, the Waste Isolation Pilot Plant recently received regulatory approval to change the disposal panel closure design from an engineered barrier constructed of a salt-based concrete to one that employs simple run-of-mine salt and temporary bulkheads for isolation from ventilation. The Waste Isolation Pilot Plant is a radioactive waste disposal repository for defense-related transuranic elements mined from the Permian evaporite salt beds in southeast New Mexico. Its approved shaft seal design incorporates barrier components comprising salt-based concrete, bentonite, and substantial depths of crushed salt compacted to enhance reconsolidation. This paper will focus on crushed salt behavior when applied as drift closures to isolate disposal rooms during operations. Scientific aspects of salt reconsolidation have been studied extensively. The technical basis for geotechnical barrier performance has been strengthened by recent experimental findings and analogue comparisons. The panel closure change was accompanied by recognition that granular salt will return to a physical state similar to the halite surrounding it. Use of run-of-mine salt ensures physical and chemical compatibility with the repository environment and simplifies ongoing disposal operations. Our current knowledge and expected outcome of research can be assimilated with lessons learned to put forward designs and operational concepts for the next generation of salt repositories. Mined salt

Reconsolidated Salt as a Geotechnical Barrier

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gadbury, Casey [USDOE Carlsbad Field Office, NM (United States)

2015-11-01

Salt as a geologic medium has several attributes favorable to long-term isolation of waste placed in mined openings. Salt formations are largely impermeable and induced fractures heal as stress returns to equilibrium. Permanent isolation also depends upon the ability to construct geotechnical barriers that achieve nearly the same high-performance characteristics attributed to the native salt formation. Salt repository seal concepts often include elements of reconstituted granular salt. As a specific case in point, the Waste Isolation Pilot Plant recently received regulatory approval to change the disposal panel closure design from an engineered barrier constructed of a salt-based concrete to one that employs simple run-of-mine salt and temporary bulkheads for isolation from ventilation. The Waste Isolation Pilot Plant is a radioactive waste disposal repository for defense-related transuranic elements mined from the Permian evaporite salt beds in southeast New Mexico. Its approved shaft seal design incorporates barrier components comprising salt-based concrete, bentonite, and substantial depths of crushed salt compacted to enhance reconsolidation. This paper will focus on crushed salt behavior when applied as drift closures to isolate disposal rooms during operations. Scientific aspects of salt reconsolidation have been studied extensively. The technical basis for geotechnical barrier performance has been strengthened by recent experimental findings and analogue comparisons. The panel closure change was accompanied by recognition that granular salt will return to a physical state similar to the halite surrounding it. Use of run-of-mine salt ensures physical and chemical compatibility with the repository environment and simplifies ongoing disposal operations. Our current knowledge and expected outcome of research can be assimilated with lessons learned to put forward designs and operational concepts for the next generation of salt repositories. Mined salt

Salt repository project site study plan for water resources: Revision 1

International Nuclear Information System (INIS)

1987-12-01

The Site Study Plan for Water Resources describes a field program consisting of surface-water and ground-water characterization. The surface-water studies will determine the drainage basin characteristics (i.e., topography, soils, land use), hydrometeorology, runoff to streams and playas, and surface-water quality (i.e., offsite pollution sources in playa lakes and in streams). The environmental ground-water studies will focus on ground-water quality characterization. The site study plan describes for each study the need for the study, study design, data management and use, schedule of proposed activities, and quality assurance. These studies will provide data needed to satisfy requirements contained in, or derived from, the Salt Repository Projects Requirements Document. 78 refs., 8 figs., 5 tabs

Salton Sea geothermal field as a natural analog for the near-field in a salt high-level nuclear waste repository

International Nuclear Information System (INIS)

Elders, W.A.; Moody, J.B.; Battelle Memorial Inst., Columbus, OH)

1984-01-01

The Salton Sea Geothermal Field (SSGF), on the delta of the Colorado River in southern California, is being studied as a natural analog for the near-field environment of proposed nuclear waste repositories in salt. A combination of mineralogical and geochemical methods is being employed to develop a three-dimenisonal picture of temperature, salinity, lithology, mineralogy, and chemistry of reactions between the reservoir rocks and the hot brines. Our aim is to obtain quantitative data on mineral stabilities and on mobilities of the naturally occurring radionuclides of concern in Commercial High-Level Waste (CHLW). These data will be used to validate the EQ3/6 geochemical code under development to model the salt near-field repository behavior. Maximum temperatures encountered in wells in the SSGF equal or exceed peak temperatures expected in a salt repository. Brines produced from these wells have major element chemistry similar to brines from candidate salt sites. Relative to the rocks, these brines are enriched in Na, Mn, Sr, Ra, and Po, depleted in Ba, Si, Mg, Ti, and Al, and strongly depleted in U and Th. However, the unaltered rocks contain only about 2 to 3 ppm of U and 4 to 12 ppm of Th, largely in detrital epidotes and zircons. Samples of hydrothermally altered rocks from a wide range of temperature and salinity show rather similar uniform low concentrations of these elements, even when authigenic illite, chlorite, ipidote and feldspar are present. These observations suggest that U and Th are relatively immobile in these hot brines. However, Ra, Po, Cs, and Sr are relatively mobile. Work is continuing to document naturally occurring radionuclide partitioning between SSGF minears and brine over a range of temperature, salinity, and lithology. 8 refs., 7 figs., 2 tabs

Repository environmental parameters and models/methodologies relevant to assessing the performance of high-level waste packages in basalt, tuff, and salt

Energy Technology Data Exchange (ETDEWEB)

Claiborne, H.C.; Croff, A.G.; Griess, J.C.; Smith, F.J.

1987-09-01

This document provides specifications for models/methodologies that could be employed in determining postclosure repository environmental parameters relevant to the performance of high-level waste packages for the Basalt Waste Isolation Project (BWIP) at Richland, Washington, the tuff at Yucca Mountain by the Nevada Test Site, and the bedded salt in Deaf Smith County, Texas. Guidance is provided on the identify of the relevant repository environmental parameters; the models/methodologies employed to determine the parameters, and the input data base for the models/methodologies. Supporting studies included are an analysis of potential waste package failure modes leading to identification of the relevant repository environmental parameters, an evaluation of the credible range of the repository environmental parameters, and a summary of the review of existing models/methodologies currently employed in determining repository environmental parameters relevant to waste package performance. 327 refs., 26 figs., 19 tabs.

Repository environmental parameters and models/methodologies relevant to assessing the performance of high-level waste packages in basalt, tuff, and salt

International Nuclear Information System (INIS)

Claiborne, H.C.; Croff, A.G.; Griess, J.C.; Smith, F.J.

1987-09-01

This document provides specifications for models/methodologies that could be employed in determining postclosure repository environmental parameters relevant to the performance of high-level waste packages for the Basalt Waste Isolation Project (BWIP) at Richland, Washington, the tuff at Yucca Mountain by the Nevada Test Site, and the bedded salt in Deaf Smith County, Texas. Guidance is provided on the identify of the relevant repository environmental parameters; the models/methodologies employed to determine the parameters, and the input data base for the models/methodologies. Supporting studies included are an analysis of potential waste package failure modes leading to identification of the relevant repository environmental parameters, an evaluation of the credible range of the repository environmental parameters, and a summary of the review of existing models/methodologies currently employed in determining repository environmental parameters relevant to waste package performance. 327 refs., 26 figs., 19 tabs

Backfilling and sealing of repositories and access shafts and galleries in clay, granite and salt formations

International Nuclear Information System (INIS)

Lake, L.M.; Davies, I.L.; Gera, F.; Jorda, M.; McEwen, T.; Neerdael, B.; Schmidt, M.W.

1985-01-01

The paper summarizes the work carried out under ten Commission contracts in the field of backfilling and sealing radioactive waste repositories. It covers theoretical, laboratory and field trials and experiments involving three potential host types, namely clay, salt and hard rock. It concludes that maximum opportunity should be taken over the next 15 to 25 years with a view to obtaining first hand experience in real ground with real wastes

Numerical and experimental investigations on the time dependent behavior of a salt dome with a high-level waste repository

International Nuclear Information System (INIS)

Prij, J.; Vons, L.H.

1984-01-01

Results are presented of in-situ measurements, performed in a 300 m deep dry-drilled borehole, in the ASSE-mine. Convergence measurements at ambient as well as elevated temperatures and pressure measurements at elevated temperatures are discussed. Creep equations derived from these experiments are used for the numerical analysis of the time dependent behavior of a salt dome with a HLW repository. The analyses show that the total stresses in the salt remain compressive with deviatoric components smaller than 3 MPa. 9 references, 6 figures, 1 table

Development of an international safeguards approach to the final disposal of spent fuel in geological repositories

International Nuclear Information System (INIS)

Murphey, W.M.; Moran, B.W.; Fattah, A.

1996-01-01

The International Atomic Energy Agency (IAEA) is currently pursuing development of an international safeguards approach for the final disposal of spent fuel in geological repositories through consultants meetings and through the Program for Development of Safeguards for Final Disposal of Spent Fuel in Geological Repositories (SAGOR). The consultants meetings provide policy guidance to IAEA; SAGOR recommends effective approaches that can be efficiently implemented by IAEA. The SAGOR program, which is a collaboration of eight Member State Support Programs (MSSPs), was initiated in July 1994 and has identified 15 activities in each of three areas (i.e. conditioning facilities, active repositories, and closed repositories) that must be performed to ensure an efficient, yet effective safeguards approach. Two consultants meetings have been held: the first in May 1991 and the last in November 1995. For nuclear materials emplaced in a geological repository, the safeguards objectives were defined to be (1) to detect the diversion of spent fuel, whether concealed or unconcealed, from the repository and (2) to detect undeclared activities of safeguards concern (e.g., tunneling, underground reprocessing, or substitution in containers)

On the time-dependent behavior of a cylindrical salt dome with a high-level waste repository

International Nuclear Information System (INIS)

Prij, J.

1988-01-01

In a salt dome with a repository for high-level radioactive and heat-generating waste, thermal stresses develop. These stresses can influence the isolation capability of the salt dome if these stresses can initiate cracks or introduce movements along existing closed flaws. The influence of the thermomechanical properties of the rock salt and the surrounding rocks on the thermal stresses and the surface rise is discussed. This discussion is based on a number of finite element creep analyses of a homogeneous cylindrical salt dome. The parameters, varied in the analyses, are constants in the thermomechanical constitutive behavior of salt and rocks, and furthermore the thermal loading has been varied. It is shown that variations in the creep properties, which result in differences in creep strain rate of a factor of 100, have only a very limited influence on the thermal stresses and the surface rise. Of more importance is the elastic stiffness of the materials. In all creep analyses the thermal stresses in the salt are compressive and the shear stresses remain below 2 MPa. The results are evaluated using an analytical treatment. Based on this evaluation, it is shown that the observed trends in the numerical results have a more general character and are not strictly limited to the geometry chosen. It is concluded that the thermal stresses in the salt formation are not strongly dependent on the creep properties of the rock salt

Laboratory investigation of crushed salt consolidation and fracture healing

International Nuclear Information System (INIS)

1987-01-01

A laboratory test program was conducted to investigate the consolidation behavior of crushed salt and fracture healing in natural and artificial salt. Crushed salt is proposed for use as backfill in a nuclear waste repository in salt. Artificial block salt is proposed for use in sealing a repository. Four consolidation tests were conducted in a hydrostatic pressure vessel at a maximum pressure of 2500 psi (17.2 MPa) and at room temperature. Three 1-month tests were conducted on salt obtained from the Waste Isolation Pilot Plant and one 2-month test was conducted on salt from Avery Island. Permeability was obtained using argon and either a steady-state or transient method. Initial porosities ranged from 0.26 to 0.36 and initial permeabilities from 2000 to 50,000 md. Final porosities and permeabilities ranged from 0.05 to 0.19 and from -5 md to 110 md, respectively. The lowest final porosity (0.05) and permeability ( -5 md) were obtained in a 1-month test in which 2.3% moisture was added to the salt at the beginning of the test. The consolidation rate was much more rapid than in any of the dry salt tests. The fracture healing program included 20 permeability tests conducted on fractured and unfractured samples. The tests were conducted in a Hoek cell at hydrostatic pressures up to 3000 psi (20.6 MPa) with durations up to 8 days. For the natural rock salt tested, permeability was strongly dependent on confining pressure and time. The effect of confining pressure was much weaker in the artificial salt. In most cases the combined effects of time and pressure were to reduce the permeability of fractured samples to the same order of magnitude (or less) as the permeability measured prior to fracturing

Problems of the final storage of radioactive waste in salt formations

International Nuclear Information System (INIS)

Hofrichter, E.

1977-01-01

The geological conditions for the final storage of radioactive waste, the occurrence of salt formations, and the tectonics of salt domes are discussed. The safety of salt rocks, the impermeability of the rocks, and the thermal problems in the storage of high-activity waste are dealt with. Possibilities and preconditions of final storage in West Germany are discussed. (HPH) [de

Repository documentation rethought. A comprehensive approach from untreated waste to waste packages for final disposal

Energy Technology Data Exchange (ETDEWEB)

Anthofer, Anton Philipp; Schubert, Johannes [VPC GmbH, Dresden (Germany)

2017-11-15

The German Act on Reorganization of Responsibility for Nuclear Disposal (Entsorgungsuebergangsgesetz (EntsorgUebG)) adopted in June 2017 provides the energy utilities with the new option of transferring responsibility for their waste packages to the Federal Government. This is conditional on the waste packages being approved for delivery to the Konrad final repository. A comprehensive approach starts with the dismantling of nuclear facilities and extends from waste disposal and packaging planning to final repository documentation. Waste package quality control measures are planned and implemented as early as in the process qualification stage so that the production of waste packages that are suitable for final deposition can be ensured. Optimization of cask and loading configuration can save container and repository volume. Workflow planning also saves time, expenditure and exposure time for personnel at the facilities. VPC has evaluated this experience and developed it into a comprehensive approach.

Executive-style briefings on selected repository design issues

International Nuclear Information System (INIS)

1978-01-01

This document is a collection of executive-style briefings on selected repository design issues. Most of the briefings discuss differences between the US repository design bases presented in US Working Draft on Repository Physical Descriptions in a Salt Formation, prepared in support of INFCE discussions of May 1978 and the FRG-Netherlands design bases, presented in Design Study of a Radioactive Waste Repository to be Mined in a Medium-Size Salt Dome by Hamstra and Velzeboer, Netherlands Energy Research Foundation, January 1978. Advantages and disadvantages of the two sets of design bases are discussed, and the impacts of adopting either of these bases on the other's programs and positions are identified

Salt disposal of heat-generating nuclear waste

International Nuclear Information System (INIS)

Leigh, Christi D.; Hansen, Francis D.

2011-01-01

This report summarizes the state of salt repository science, reviews many of the technical issues pertaining to disposal of heat-generating nuclear waste in salt, and proposes several avenues for future science-based activities to further the technical basis for disposal in salt. There are extensive salt formations in the forty-eight contiguous states, and many of them may be worthy of consideration for nuclear waste disposal. The United States has extensive experience in salt repository sciences, including an operating facility for disposal of transuranic wastes. The scientific background for salt disposal including laboratory and field tests at ambient and elevated temperature, principles of salt behavior, potential for fracture damage and its mitigation, seal systems, chemical conditions, advanced modeling capabilities and near-future developments, performance assessment processes, and international collaboration are all discussed. The discussion of salt disposal issues is brought current, including a summary of recent international workshops dedicated to high-level waste disposal in salt. Lessons learned from Sandia National Laboratories' experience on the Waste Isolation Pilot Plant and the Yucca Mountain Project as well as related salt experience with the Strategic Petroleum Reserve are applied in this assessment. Disposal of heat-generating nuclear waste in a suitable salt formation is attractive because the material is essentially impermeable, self-sealing, and thermally conductive. Conditions are chemically beneficial, and a significant experience base exists in understanding this environment. Within the period of institutional control, overburden pressure will seal fractures and provide a repository setting that limits radionuclide movement. A salt repository could potentially achieve total containment, with no releases to the environment in undisturbed scenarios for as long as the region is geologically stable. Much of the experience gained from United

Salt disposal of heat-generating nuclear waste.

Energy Technology Data Exchange (ETDEWEB)

Leigh, Christi D. (Sandia National Laboratories, Carlsbad, NM); Hansen, Francis D.

2011-01-01

This report summarizes the state of salt repository science, reviews many of the technical issues pertaining to disposal of heat-generating nuclear waste in salt, and proposes several avenues for future science-based activities to further the technical basis for disposal in salt. There are extensive salt formations in the forty-eight contiguous states, and many of them may be worthy of consideration for nuclear waste disposal. The United States has extensive experience in salt repository sciences, including an operating facility for disposal of transuranic wastes. The scientific background for salt disposal including laboratory and field tests at ambient and elevated temperature, principles of salt behavior, potential for fracture damage and its mitigation, seal systems, chemical conditions, advanced modeling capabilities and near-future developments, performance assessment processes, and international collaboration are all discussed. The discussion of salt disposal issues is brought current, including a summary of recent international workshops dedicated to high-level waste disposal in salt. Lessons learned from Sandia National Laboratories' experience on the Waste Isolation Pilot Plant and the Yucca Mountain Project as well as related salt experience with the Strategic Petroleum Reserve are applied in this assessment. Disposal of heat-generating nuclear waste in a suitable salt formation is attractive because the material is essentially impermeable, self-sealing, and thermally conductive. Conditions are chemically beneficial, and a significant experience base exists in understanding this environment. Within the period of institutional control, overburden pressure will seal fractures and provide a repository setting that limits radionuclide movement. A salt repository could potentially achieve total containment, with no releases to the environment in undisturbed scenarios for as long as the region is geologically stable. Much of the experience gained from

A new approach to performance assessment of barriers in a repository. Executive summary, draft, technical appendices. Final report

International Nuclear Information System (INIS)

Mueller-Hoeppe, N.; Krone, J.; Niehues, N.; Poehler, M.; Raitz von Frentz, R.; Gauglitz, R.

1999-06-01

Multi-barrier systems are accepted as the basic approach for long term environmental safe isolation of radioactive waste in geological repositories. Assessing the performance of natural and engineered barriers is one of the major difficulties in producing evidence of environmental safety for any radioactive waste disposal facility, due to the enormous complexity of scenarios and uncertainties to be considered. This report outlines a new methodological approach originally developed basically for a repository in salt, but that can be transferred with minor modifications to any other host rock formation. The approach is based on the integration of following elements: (1) Implementation of a simple method and efficient criteria to assess and prove the tightness of geological and engineered barriers; (2) Using the method of Partial Safety Factors in order to assess barrier performance at certain reasonable level of confidence; (3) Integration of a diverse geochemical barrier in the near field of waste emplacement limiting systematically the radiological consequences from any radionuclide release in safety investigations and (4) Risk based approach for the assessment of radionuclide releases. Indicative calculations performed with extremely conservative assumptions allow to exclude any radiological health consequences from a HLW repository in salt to a reference person with a safety level of 99,9999% per year. (orig.)

Refinancing of the search for a repository and of the repository for heat generating radioactive waste. Pt. 1

International Nuclear Information System (INIS)

Moench, Christoph

2013-01-01

The final disposal of radioactive waste is a state task that is assigned to the Federal Government pursuant to section 9a (3) sentence 1 of the Atomic Energy Act (AtG). Since the early 1970's, the Federal Government has been actively searching for and exploring final disposal sites for radioactive waste. In a proceeding accompanied by the intensive participation of technical experts and the public, the Gorleben salt dome (Salzstock) has emerged as a presumably suitable disposal site from a mining standpoint (eignungshoeffig) according to the current status of the exploration. The cost of these exploratory measures - and the subsequent construction - will be financed by the waste producers, in particular the utility companies, by means of advance payments on their contributions. Part I of this article will evaluate the selection and exploration of the Gorleben salt dome to date and examine the provisions on the pre-financing burden from the point of view of constitutional law. Constitutional objections can also be raised against the regulation in section 21b (4) AtG that was introduced in 1998, which excludes a refunding of the pre-financing contributions even if the repository is never erected or operated. Part II of this article, which will appear in the next issue, will take up the question of whether a search for an alternative repository site, as the Federal Ministry for the Environment (BMU) envisions in the working draft of an 'Act on the search for and selection of a site for a repository for heat generating radioactive waste' (Gesetz zur Suche und Auswahl eines Standortes fuer ein Endlager fuer waermeentwickelnde radioaktive Abfaelle), is likewise to be refinanced as a contribution by the parties obliged to make advance payments. (orig.)

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, vertical emplacement mode: Volume 1

International Nuclear Information System (INIS)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packing, and other surface facility operations are described. Operations in the shafts underground are described, including waste hoisting, transfer, and vertical emplacement. This report specifically addresses the vertical emplacement mode, the reference design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, vertical emplacement mode: Volume 1

Energy Technology Data Exchange (ETDEWEB)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packing, and other surface facility operations are described. Operations in the shafts underground are described, including waste hoisting, transfer, and vertical emplacement. This report specifically addresses the vertical emplacement mode, the reference design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs.

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, horizontal emplacment mode: Volume 1

International Nuclear Information System (INIS)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packaging, and other surface facility operations are described. Operations in the shafts and underground are described, including waste hoisting, transfer, and horizontal emplacement. This report specifically addresses the horizontal emplacement mode, the passive alternate design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs

Development of a technical concept for a generic final repository for heat-generating wastes and spent fuel elements in crystalline rock formations in Germany. Final report; Entwicklung eines technischen Konzeptes fuer ein generisches Endlager fuer waermeentwickelnde Abfaelle und ausgediente Brennelemente im Kristallingestein in Deutschland. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Bertrams, Niklas; Herold, Philipp; Herold, Maxi; Krone, Juergen; Lommerzheim, Andree; Prignitz, Sabine; Kuate, Eric Simo

2017-09-15

The research project concerning the development of a generic concept for final repositories in crystalline rock formations has identified three different concepts for long-term safe enclosure efficacy: (i) the KBS-3 concept as pursued in Sweden and Finland based on corrosion resistant copper containers and bentonite buffers in vertical bore holes; (ii) The concept of ''multiple enclosure efficient rock zones'', based on several spatially separated rock zones that allow the demonstration of efficient enclosure; (iii) the concept of a ''superposed enclosure efficient rock zone'', where a sedimentary coverage of the crystalline host rock (for instance clay or salt) shows enclosure efficacy. For each of these concepts a separate final repository concept was developed covering the construction of shafts, ramps and transport routes, the preparation of boreholes, and the backfilling and closure technology, the planning of mine buildings, ventilation, time and cost estimation.

Sandia studies of high-level waste canisters and overpacks applicable for a salt repository

International Nuclear Information System (INIS)

Molecke, M.A.; Schaefer, D.W.; Glass, R.S.; Ruppen, J.A.

1982-01-01

An experimental program to develop candidate materials for use as high-level waste (HLW) overpacks or canisters in a salt repository has been in progress at Sandia National Laboratories since 1976. The main objective of this program is to provide a waste package barrier having a long lifetime in the chemical and physical environment of a repository. This paper summarizes the recent corrosion and metallurgical study results for the prime overpack material, TiCode-12, in the areas of uniform corrosion (extremely low rate and extent); local attack, e.g., pits and crevices (none were found); stress corrosion cracking susceptibility (no significant changes in macroscopic tensile properties were detected); hydrogen sorption-embrittlement effects; effects of gamma irradiation in solution; and sensitization effects (testing is still in process in the last three areas). Previous candidate screening analyses on other alloys and recent work on alternate overpack alloys are reviewed. All phases of these interrelated laboratory, hot-cell, and field experimental studies are described. 16 references, 8 figures, 4 tables

Development of a central final repository management for the coordination of the waste for Schacht Konrad from public authorities

International Nuclear Information System (INIS)

Graffunder, Iris; Dominke-Bendix, Carola; Waldek, Achim

2012-01-01

The central final repository management is supposed to fulfill the following tasks: active collaboration of Konrad contract draft, signing of internal contracts and agreements, cooperation contract with GNS, cooperation with coordination authorities, inventory taking of wastes (existing inventory and prognosis) and interim storage capacities of public authorities, development of planning and management software, optimization of the final repository documentation, container management, logistics concept, long-term disposal planning and prognosis, planning and coordination of the annual waste amount, management and documentation of disposed waste allocation, coordination of transport schedules, consulting service for waste obligations (final repository requirements, product control, documentation).

Brine: a computer program to compute brine migration adjacent to a nuclear waste canister in a salt repository

International Nuclear Information System (INIS)

Duckworth, G.D.; Fuller, M.E.

1980-01-01

This report presents a mathematical model used to predict brine migration toward a nuclear waste canister in a bedded salt repository. The mathematical model is implemented in a computer program called BRINE. The program is written in FORTRAN and executes in the batch mode on a CDC 7600. A description of the program input requirements and output available is included. Samples of input and output are given

Geoprospective study of a nuclear waste repository: salt domes; Bibliographic study of their genesis

International Nuclear Information System (INIS)

Billaux, D.; Robelin, C.

1985-01-01

This report appraises, from the results of a bibliographical study, the possibility of beginning of a domal rise from the salt layer in which or above which would have been placed a repository. The physical mecanisms of salt creep are first screened, together with the factors determining their intensity and relative importance. These factors are primarily the temperature and the state of stress. Semi empirical laws are given for some mecanisms. Present knowledge about the state of the salt in the ground are then examined: we are not able to satisfactorily calculate ''in situ'' stresses, or to explain the existence of an important shear stress, that has been pointed out by most of the stress measurements. The retrospective study of the genesis of existing domes brings an insight into their correlation with sedimentary and tectonic phases. Model studies help us to interpret the distances between domes, and to explain the scale of this phenomenon. After recapitulating the various factors of some importance, we find that the probability of a dome rise from a previously static layer is low, in the time lap we are interested in (100 000 years). Such a rise would have to be triggered by important changes in the sedimentation, erosion or tectonic activity on the site

Temperature calculations on different configurations for disposal of high-level reprocessing waste in a salt dome model

International Nuclear Information System (INIS)

Hamstra, J.; Kevenaar, J.W.A.M.

1978-06-01

A medium size salt dome is considered as a structure in which a repository can be located for all radioactive wastes to be produced within the scope of a postulated nuclear power program. A dominating design factor for the lay-out of such a waste repository is the temperature distribution in the salt dome resulting from decay heat released from the buried solidified high-level reprocessing waste. Two numerical models are presented for the calculation of both global and local rock salt temperatures. The results of calculations performed with these models are demonstrated to be compatible. Rock salt temperatures related to several types of burial configurations, ranging from two layer configurations with various vertical distances between the layers via a three and a four layer repository to deep bore hole concepts varying from 100 to 600 m bore hole depth, can therefore be calculated with one rather simple unit cell model. The results of these calculations indicate that rock salt temperatures can be kept within acceptable limits to realize a repository using standard mining techniques. The temperatures at mine galery level prove to be a dominating factor in the selection of a repository configuration. More detailed calculations of these temperatures taking into account the loading sequence and the cooling capacity of the mine ventilation are recommended. Finally the apparent advantages of a deep bore hole concept emphasize the need for R and D work with respect to advanced drilling techniques in order to achieve deep dry disposal bore holes that can be realized from a burial mine in the salt dome. (Auth.)

Nuclear waste repository design and construction

International Nuclear Information System (INIS)

Bohlke, B.M.; Monsees, J.E.

1987-01-01

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt

Formation and fate of gases in the caverns of a repository in salt rock

International Nuclear Information System (INIS)

Mueller, W.; Morlock, G.; Gronemeyer, C.

1992-01-01

The report summarizes the knowledge avaible today of the mechanisms governing the formation and transport of gases in a salt mine repository for radioactive wastes. The work under review deals with the formation of gases-by way of radiolysis, corrosion, microbial degradation, thermally induced or primary gas generation - and analyses the efficiency of predicting and modelling the gas generation mechanisms in terms of the role of parameters involved, and accuracy. Existing gaps in available knowledge are shown and defined in terms of significance, leading to an analysis of interdependencies between the various mechanisms and to a statement concerning the necessity of establishing materials balances. (orig./EF) [de

Reference concepts for the final disposal of LWR spent fuel and other high activity wastes in Spain

International Nuclear Information System (INIS)

Huertas, F.; Ulibarri, A.

1993-01-01

Studies over the last three years have been recently concluded with the selection of a reference repository concept for the final disposal of spent fuel and other high activity wastes in deep geological formations. Two non-site specific preliminary designs, at a conceptual level, have been developed; one considers granite as the host rock and the other rock salt formations. The Spanish General Radioactive Waste Program also considers clay as a potential host rock for HLW deep disposal; conceptualization for a deep repository in clay is in the initial phase of development. The salt repository concept contemplates the disposal of the HLW in self-shielding casks emplaced in the drifts of an underground facility, excavated at a depth of 850 m in a bedded salt formation. The Custos Type I(7) cask admits up to seven intact PWR fuel assemblies or 21 of BWR type. The final repository facilities are planned to accept a total of 20,000 fuel assemblies (PWR and BWR) and 50 vitrified waste canisters over a period of 25 years. The total space needed for the surface facilities amounts to 322,000 m 2 , including the rock salt dump. The space required for the underground facilities amounts to 1.2 km 2 , approximately. The granite repository concept contemplates the disposal of the HLW in carbon steel canisters, embedded in a 0.75 m thick buffer of swelling smectite clay, in the drifts of an underground facility, excavated at a depth of 55 m in granite. Each canister can host 3 PWR or 9 BWR fuel assemblies. For this concept the total number of canisters needed amounts to 4,860. The space required for the surface and underground facilities is similar to that of the salt concept. The technical principles and criteria used for the design are discussed, and a description of the repository concept is presented

Studies of mechanisms and processes of relevance to the safety of nuclear waste repositories, as carried out prior to, during and after flovelling of the Hope potash salt mine

International Nuclear Information System (INIS)

1985-01-01

Studies on the effects of a hypothetical accident involving water or brine intrusion into a waste repository in a salt mine are of special importance within the framework of safety assessments of salt formations as candidate sites for nuclear waste repositories. The measuring activities under review include the following: Physicochemical measurements for determining dissolution and recipitation of salts, transport mechanisms, temperature curves, natural build-up and efficiency of geochemical barriers in the brine. Geochemical measurements for obtaining information on the rock deformation prior to, during, and after flovelling. Geophysical measurements of microseismic behaviour of rock masses prior to, during, and after flovelling. Examination of an artificial barrier structure for the testing and assessment of technical barriers and their efficiency. (orig./HP) [de

Systems costs for disposal of Savannah River high-level waste sludge and salt

International Nuclear Information System (INIS)

McDonell, W.R.; Goodlett, C.B.

1984-01-01

A systems cost model has been developed to support disposal of defense high-level waste sludge and salt generated at the Savannah River Plant. Waste processing activities covered by the model include decontamination of the salt by a precipitation process in the waste storage tanks, incorporation of the sludge and radionuclides removed from the salt into glass in the Defense Waste Processing Facility (DWPF), and, after interim storage, final disposal of the DWPF glass waste canisters in a federal geologic repository. Total costs for processing of waste generated to the year 2000 are estimated to be about $2.9 billion (1984 dollars); incremental unit costs for DWPF and repository disposal activities range from $120,000 to $170,000 per canister depending on DWPF processing schedules. In a representative evaluation of process alternatives, the model is used to demonstrate cost effectiveness of adjustments in the frit content of the waste glass to reduce impacts of wastes generated by the salt decontamination operations. 13 references, 8 tables

Concepts and Technologies for Radioactive Waste Disposal in Rock Salt

Directory of Open Access Journals (Sweden)

Wernt Brewitz

2007-01-01

Full Text Available In Germany, rock salt was selected to host a repository for radioactive waste because of its excellent mechanical properties. During 12 years of practical disposal operation in the Asse mine and 25 years of disposal in the disused former salt mine Morsleben, it was demonstrated that low-level wastes (LLW and intermediate-level wastes (ILW can be safely handled and economically disposed of in salt repositories without a great technical effort. LLW drums were stacked in old mining chambers by loading vehicles or emplaced by means of the dumping technique. Generally, the remaining voids were backfilled by crushed salt or brown coal filter ash. ILW were lowered into inaccessible chambers through a borehole from a loading station above using a remote control.Additionally, an in-situ solidification of liquid LLW was applied in the Morsleben mine. Concepts and techniques for the disposal of heat generating high-level waste (HLW are advanced as well. The feasibility of both borehole and drift disposal concepts have been proved by about 30 years of testing in the Asse mine. Since 1980s, several full-scale in-situ tests were conducted for simulating the borehole emplacement of vitrified HLW canisters and the drift emplacement of spent fuel in Pollux casks. Since 1979, the Gorleben salt dome has been investigated to prove its suitability to host the national final repository for all types of radioactive waste. The “Concept Repository Gorleben” disposal concepts and techniques for LLW and ILW are widely based on the successful test operations performed at Asse. Full-scale experiments including the development and testing of adequate transport and emplacement systems for HLW, however, are still pending. General discussions on the retrievability and the reversibility are going on.

Salton Sea Geothermal Field, California, as a near-field natural analog of a radioactive waste repository in salt

International Nuclear Information System (INIS)

Elders, W.A.; Cohen, L.H.

1983-11-01

Since high concentrations of radionuclides and high temperatures are not normally encountered in salt domes or beds, finding an exact geologic analog of expected near-field conditions in a mined nuclear waste repository in salt will be difficult. The Salton Sea Geothermal Field, however, provides an opportunity to investigate the migration and retardation of naturally occurring U, Th, Ra, Cs, Sr and other elements in hot brines which have been moving through clay-rich sedimentary rocks for up to 100,000 years. The more than thirty deep wells drilled in this field to produce steam for electrical generation penetrate sedimentary rocks containing concentrated brines where temperatures reach 365 0 C at only 2 km depth. The brines are primarily Na, K, Ca chlorides with up to 25% of total dissolved solids; they also contain high concentrations of metals such as Fe, Mn, Li, Zn, and Pb. This report describes the geology, geophysics and geochemistry of this system as a prelude to a study of the mobility of naturally occurring radionuclides and radionuclide analogs within it. The aim of this study is to provide data to assist in validating quantitative models of repository behavior and to use in designing and evaluating waste packages and engineered barriers. 128 references, 33 figures, 13 tables

Salton Sea Geothermal Field, California, as a near-field natural analog of a radioactive waste repository in salt

Energy Technology Data Exchange (ETDEWEB)

Elders, W.A.; Cohen, L.H.

1983-11-01

Since high concentrations of radionuclides and high temperatures are not normally encountered in salt domes or beds, finding an exact geologic analog of expected near-field conditions in a mined nuclear waste repository in salt will be difficult. The Salton Sea Geothermal Field, however, provides an opportunity to investigate the migration and retardation of naturally occurring U, Th, Ra, Cs, Sr and other elements in hot brines which have been moving through clay-rich sedimentary rocks for up to 100,000 years. The more than thirty deep wells drilled in this field to produce steam for electrical generation penetrate sedimentary rocks containing concentrated brines where temperatures reach 365/sup 0/C at only 2 km depth. The brines are primarily Na, K, Ca chlorides with up to 25% of total dissolved solids; they also contain high concentrations of metals such as Fe, Mn, Li, Zn, and Pb. This report describes the geology, geophysics and geochemistry of this system as a prelude to a study of the mobility of naturally occurring radionuclides and radionuclide analogs within it. The aim of this study is to provide data to assist in validating quantitative models of repository behavior and to use in designing and evaluating waste packages and engineered barriers. 128 references, 33 figures, 13 tables.

Project Guarantee 1985. Final repository for high-level radioactive wastes: The system of safety barriers

International Nuclear Information System (INIS)

Anon.

1985-01-01

Final disposal of radioactive waste involves preventing the waste from returning from the repository location into the biosphere by means of successively arranged containment measures known as safety barriers. In the present volume NGB 85-04 of the series of reports for Project 'Guarantee' 1985, the safety barrier system for the type C repository for high-level waste is described. The barrier parameters which are relevant for safety analysis are quantified and associated error limits and data scatter are given. The aim of the report is to give a summary documentation of the safety analysis input data and their scientific background. For secure containment of radioactive waste safety barriers are used which effectively limit the release of radioactive material from the repository (release barriers) and effectively retard the entry of the original radioactive material into the biosphere (time barriers). Safety barriers take the form of both technically constructed containment measures and the siting of the repository in suitable geological formations. The technical safety barrier system in the case of high-level waste comprises: the waste solidification matrix (borosilicate glass), massive steel canisters, encasement of the waste canisters, encasement of the waste canisters in highly compacted bentonite, sealing of vacant storage space and access routes on repository closure. The natural geological safety barriers - the host rock and overlying formations provide sufficiently long deep groundwater flow times from the repository location to the earth's surface and for additional lengthening of radionuclide migration times by means of various chemical and physical retardation mechanisms. The stability of the geological formations is so great that hydrogeological system is protected for a sufficient length of time from deterioration caused, in particular, by erosion. Observations in the final section of the report indicate that input data for the type C repository safety

Preliminary access routes and cost study analyses for seven potentially acceptable salt sites: Final report, October 1984

International Nuclear Information System (INIS)

1987-02-01

This report analyzes highway and railroad access to seven potentially acceptable salt repository sites: Richton Dome and Cypress Creek Dome in Mississippi, Vacherie Dome in Louisiana, Swisher County and Deaf Smith County in Texas, and Davis Canyon and Lavender Canyon in utah. The objectives of the study were to investigate the routing of reasonable access corridors to the sites, describe major characteristics of each route, and estimate the costs for constructing or upgrading highways and railroads. The routes used in the analysis are not necessarily recommended or preferred over other routes, nor do they represent an implied final selection. Detailed engineering studies must be performed for the Davis Canyon and Lavender Canyon highway access before the analyzed routes can be considered to be viable. 20 refs., 7 figs., 3 tabs

Life cycle assessment of geological repositories for the final disposal of spent fuel in Finland and Sweden

International Nuclear Information System (INIS)

Puhrer, A.; Bauer, C.

2014-01-01

This paper presents a Life Cycle Assessment (LCA) of the geological repositories for the final disposal of spent nuclear fuel in Finland and Sweden. A separate LCA has been performed for the geological spent fuel repository in each country and the results have been compared. A further benchmark comparison has been made with the LCA of the Swiss geological repository for high-level waste and spent fuel. The life cycle inventory (LCI) product system boundaries include the spent fuel repository and encapsulation facility in each country. All materials, processes, consumed utilities and transport associated with the construction, operation and closure of the repositories for spent fuel are included in the LCI. The life cycle impact assessment (LCIA) is performed using two methods: IPCC 2007 Climate Change and ReCiPe. These assessment methods return results pertaining to global warming potential (GWP) as well as a number of environmental impact categories such as human toxicity and natural land transformation. Results indicate that the use of copper for disposal canister fabrication and bentonite for repository backfilling are the causes for most of the environmental impact of the spent fuel repositories in Finland and Sweden. Alternate, less bentonite-intensive backfilling scenarios may mitigate this impact. While the Swiss bentonite consumption is lower and no copper is used for canister fabrication, the Swiss electricity and fuel consumption associated with final disposal of high-level waste and spent fuel is significantly higher than in Finland or Sweden. Approximately 1 g CO 2 -eq is emitted due to the final disposal of spent fuel and HLW per kWh of nuclear generated electricity. This represents some 10% of the emissions due to the entire nuclear energy chain and is practically negligible in the context of GHG emissions of other energy technologies. (authors)

Geological status of NWTS repository siting activities in the paradox basin

International Nuclear Information System (INIS)

Frazier, N.A.; Conwell, F.R.

1981-01-01

Emplacement of waste packages in mined geological repositories is one method being evaluated for isolating high-level nuclear wastes. Granite, dome salt, tuff, basalt and bedded salt are among the rock types being investigated. Described in this paper is the status of geological activities in the Paradox Basin of Utah and Colorado, one region being explored as a part of the National Waste Terminal Storage (NWTS) program to site a geological repository in bedded salt

Safety and performance indicators for repositories in salt and clay formations

International Nuclear Information System (INIS)

Wolf, Jens; Ruebel, Andre; Noseck, Ulrich; Becker, Dirk

2008-07-01

The GRS (Gesellschaft fuer Reaktorsicherheit) study aims to the identification of suitable indicators for repositories in salt and clay formation. It is not intended to compare the two formations with respect to the safe disposal of radioactive waste. A first set of safety and performance indicators for both host rocks has been derived on the basis of results of the SPIN project. Reference values for the safety indicators have been determined. The suitability of the indicators and their significance for different time frames Is demonstrated by means of deterministic model calculations and external parameter variations of previous studies. The safety indicators considered in the report are the effective dose rate (Sv/a), the radiotoxicity concentration in the biosphere water (Sv/m 3 ) and the radiotoxicity flux from the geosphere (overlying rock) (Sv/a). The performance indicators considered in the study are the radiotoxicity inventory in different compartments (S), radiotoxicity fluxes from compartments and the integrated radiotoxicity fluxes from compartments (Sv).

Final storage of radioactive waste - how soon will we be able to catch up again with international developments?

International Nuclear Information System (INIS)

Kuehn, K.

2006-01-01

In Germany, the final storage of radioactive waste from the beginning has been a topic very much influenced by the political debate, especially by party politics. The development initiated after the 1998 change in government has greatly contributed to Germany clearly losing contact with cutting edge international developments in final storage. Here are some proposals for improving the present situation: - The political demand for a single-repository concept should be given up. - Preparatory work on the Konrad repository should be started. - Underground exploration of the Gorleben salt dome should be resumed without any strings attached. - A TSPA should be conducted for the Gorleben project. - After completion of the TSPA, an international peer review should be carried out of the Gorleben project. - An underground laboratory in salt should be established in Germany. - Repository activities should be transferred to a company organized and operating along industrial lines. - Competence for licensing radioactive waste repositories should be concentrated on a national level. (orig.)

Thermomechanical repository and shaft response analyses using the CAVS [Cracking And Void Strain] jointed rock model: Draft final report

International Nuclear Information System (INIS)

Dial, B.W.; Maxwell, D.E.

1986-12-01

Numerical studies of the far-field repository and near-field shaft response for a nuclear waste repository in bedded salt have been performed with the STEALTH computer code using the CAVS model for jointed rock. CAVS is a constitutive model that can simulate the slip and dilatancy of fracture planes in a jointed rock mass. The initiation and/or propagation of fractures can also be modeled when stress intensity criteria are met. The CAVS models are based on the joint models proposed with appropriate modifications for numerical simulations. The STEALTH/CAVS model has been previously used to model (1) explosive fracturing of a wellbore, (2) earthquake effects on tunnels in a generic nuclear waste repository, (3) horizontal emplacement for a nuclear waste repository in jointed granite, and (4) tunnel response in jointed rock. The use of CAVS to model far-field repository and near-field shaft response was different from previous approaches because it represented a spatially oriented approach to rock response and failure, rather than the traditional stress invariant formulation for yielding. In addition, CAVS tracked the response of the joint apertures to the time-dependent stress changes in the far-field repository and near-field shaft regions. 28 refs., 21 figs., 11 tabs

Expedited demonstration of molten salt mixed waste treatment technology. Final report

International Nuclear Information System (INIS)

1995-01-01

This final report discusses the molten salt mixed waste project in terms of the various subtasks established. Subtask 1: Carbon monoxide emissions; Establish a salt recycle schedule and/or a strategy for off-gas control for MWMF that keeps carbon monoxide emission below 100 ppm on an hourly averaged basis. Subtask 2: Salt melt viscosity; Experiments are conducted to determine salt viscosity as a function of ash composition, ash concentration, temperature, and time. Subtask 3: Determine that the amount of sodium carbonate entrained in the off-gas is minimal, and that any deposited salt can easily be removed form the piping using a soot blower or other means. Subtask 4: The provision of at least one final waste form that meets the waste acceptance criteria of a landfill that will take the waste. This report discusses the progress made in each of these areas

Mixed Waste Salt Encapsulation Using Polysiloxane - Final Report

International Nuclear Information System (INIS)

Miller, C.M.; Loomis, G.G.; Prewett, S.W.

1997-01-01

A proof-of-concept experimental study was performed to investigate the use of Orbit Technologies polysiloxane grouting material for encapsulation of U.S. Department of Energy mixed waste salts leading to a final waste form for disposal. Evaporator pond salt residues and other salt-like material contaminated with both radioactive isotopes and hazardous components are ubiquitous in the DOE complex and may exceed 250,000,000 kg of material. Current treatment involves mixing low waste percentages (less than 10% by mass salt) with cement or costly thermal treatment followed by cementation to the ash residue. The proposed technology involves simple mixing of the granular salt material (with relatively high waste loadings-greater than 50%) in a polysiloxane-based system that polymerizes to form a silicon-based polymer material. This study involved a mixing study to determine optimum waste loadings and compressive strengths of the resultant monoliths. Following the mixing study, durability testing was performed on promising waste forms. Leaching studies including the accelerated leach test and the toxicity characteristic leaching procedure were also performed on a high nitrate salt waste form. In addition to this testing, the waste form was examined by scanning electron microscope. Preliminary cost estimates for applying this technology to the DOE complex mixed waste salt problem is also given

Proceedings of the 6th US/German Workshop on Salt Repository Research, Design, and Operation

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Steininger, Walter [Karlsruhe Inst. of Technology (KIT) (Germany); Bollingerfehr, Wilhelm [DBE Technology GmbH, Peine (Germany)

2016-01-11

The 6th US/German Workshop on Salt Repository Research, Design, and Operation was held in Dresden. Germany on September 7-9, 2015. Over seventy participants helped advance the technical basis for salt disposal of radioactive waste. The number of collaborative efforts continues to grow and to produce useful documentation, as well as to define the state of the art for research areas. These Proceedings are divided into Chapters, and a list of authors is included in the Acknowledgement Section. Also in this document are the Technical Agenda, List of Participants, Biographical Information, Abstracts, and Presentations. Proceedings of all workshops and other pertinent information are posted on websites hosted by Sandia National Laboratories and the Nuclear Energy Agency Salt Club. The US/German workshops provide continuity for long-term research, summarize and publish status of mature areas, and develop appropriate research by consensus in a workshop environment. As before, major areas and findings are highlighted, which constitute topical Chapters in these Proceedings. In total, the scientific breadth is substantial and while not all subject matter is elaborated into chapter format, all presentations and abstracts are published in this document. In the following Proceedings, six selected topics are developed in detail.

Geoscience data base handbook for modeling a nuclear waste repository. Volume 1

International Nuclear Information System (INIS)

Isherwood, D.

1979-12-01

This handbook contains reference information on parameters that should be considered in analyzing or modeling a proposed nuclear waste repository site. Only those parameters and values that best represent the natural environment are included. Rare extremes are avoided. Where laboratory and field data are inadequate, theoretical treatments and informed engineering judgements are presented. Volume 1 contains a data base on salt as a repository medium. Chapters on the geology of bedded and dome salt, the geomechanics of salt, hydrology, geochemistry, natural and man-made features, and seismology provide compiled data and related information useful for studying a proposed repository in salt. These and other data will be needed to derive generic deep geologic modeling parameters and will also serve as background for the verification of source data that may be presented in licensing applications for nuclear waste repositories. Volume 2 is the result of a scoping study for a data base on the geology, geomechanics, and hydrology of shale, granite, and basalt as alternative repository media. Except for the geomechanics of shale, most of the sections contain relatively complete compilations of the available data, as well as discussions of the properties that are unique to each rock type

Operational analysis supporting the definition of the repository/transportation interface

International Nuclear Information System (INIS)

Peterson, R.W.; Smith, L.A.; Wampler, J.A.

1985-06-01

This report discusses progress made to date in an on-going effort to analyze operations at the repository-transportation interface of the Mined Geologic Disposal System of the Salt Repository Project (SRP). The interface is where the two systems actually are in physical contact with one another. The overall intent of the on-going effort is to to evaluate several interface design concepts for the extent to which workers are exposed to radiation, for the time required to receive and process transportation casks, and for the associated capital and operating costs. The design criteria report will outline interface functional requirements, which when incorporated into the interfacing systems (transportation-repository receiving), will ensure their physical compatibility, their optimal operation, and their compliance with performance standards. The final design criteria report will subsequently serve as an input to the receiving facility design portions of the SRP System Design Description (SDD), and System Requirements Specifications (SRS), and to the transportation cask design specifications. 6 refs., 13 figs., 6 tabs

Probabilistic risk assessment for salt repository conceptual design of subsurface facilities: A techical basis for Q-list determination

International Nuclear Information System (INIS)

Chen, C.P.; Mayberry, J.J.; Shepherd, J.; Koza, H.; Rahmani, H.; Sinsky, J.

1987-12-01

Subpart G ''Quality Assurance'' of 10 CFR Part 60 requires that the US Department of Energy (DOE) apply a quality assurance program to ''all systems, structures, and components important to safety'' and to ''design and characterization of barriers important to waste isolation.'' In April 1986, DOE's Office of Geologic Repositories (OGR) issued general guidance for formulating a list of such systems, structures, and components---the Q-list. This guidance called for the use of probabilistic risk assessment (PRA) techniques to identify Q-list items. In this report, PRA techniques are applied to the underground facilities and systems described in the conceptual design report for the Salt Repository Project (SRP) in Deaf Smith County, Texas. Based on probability and dose consequence calculations, no specific items were identified for the Q-list. However, evaluation of the analyses indicated that two functions are important in precluding off-site releases of radioactivity: disposal container integrity; and isolation of the underground facility by the heating, ventilation, and air conditioning (HVAC) systems. Items related to these functions are recommended for further evaluation as the repository design progresses. 13 refs., 20 figs

The undersea location of the Swedish Final Repository for reactor waste, SFR - human intrusion aspects

International Nuclear Information System (INIS)

Eng, T.

1989-01-01

The Swedish Final Repository for reactor waste, SFR, is built under the Baltic sea close to the Forsmark nuclear power plant. Sixty metres of rock cover the repository caverns under the seabed. The depth of the Baltic sea is about 5-6 m at this location. A human intrusion scenario that in normal inland locations has shown to be of great importance, is a well that is drilled through or in the close vicinity of the repository. Since the land uplift in the SFR area is about 6 mm/year the undersea location of SFR ensures that no well will be drilled at this location for a considerable time while the area is covered by the Baltic sea

Technical bases for establishing a salt test facility

International Nuclear Information System (INIS)

1985-05-01

The need for a testing facility in which radioactive materials may be used in an underground salt environment is explored. No such facility is currently available in salt deposits in the United States. A salt test facility (STF) would demonstrate the feasibility of safely storing radioactive waste in salt and would provide data needed to support the design, construction, licensing, and operation of a radioactive waste repository in salt. Nineteen issues that could affect long-term isolation of waste materials in a salt repository are identified from the most pertinent recent literature. The issues are assigned an overall priority and a priority relative to the activities of the STF. Individual tests recommended for performance in the STF to resolve the 19 issues are described and organized under three groups: waste package performance, repository design and operation, and site characterization and evaluation. The requirements for a salt test facility are given in the form of functional criteria, and the approach that will be used in the design, execution, interpretation, and reporting of tests is discussed

Buckling design criteria for waste package disposal containers in mined salt repositories: Technical report

International Nuclear Information System (INIS)

Mallett, R.H.

1986-12-01

This report documents analytical and experimental results from a survey of the technical literature on buckling of thick-walled cylinders under external pressure. Based upon these results, a load factor is suggested for the design of waste package containers for disposal of high-level radioactive waste in repositories mined in salt formations. The load factor is defined as a ratio of buckling pressure to allowable pressure. Specifically, a load factor which ranges from 1.5 for plastic buckling to 3.0 for elastic buckling is included in a set of proposed buckling design criteria for waste disposal containers. Formulas are given for buckling design under axisymmetric conditions. Guidelines are given for detailed inelastic buckling analyses which are generally required for design of disposal containers

Attitudes towards a final repository for the spent nuclear fuel. Structure and causes

International Nuclear Information System (INIS)

Sjoeberg, Lennart

2008-09-01

This report presents the results of a questionnaire survey of attitudes towards a final repository for the spent nuclear fuel. The questionnaire was mailed to 3,000 persons. Participants were young and older people in Oskarshamn municipality and Oesthammar municipality as well as in the rest of the country. Fifty-one percent responded. The questionnaire included a large number of questions of possible relevance for understanding the structure of and reasons for the person's attitude towards a final repository. Questions concerning nuclear power were dealt with in a special section. Men were more positively disposed towards a repository than women, older people more than young. The gender differences are mainly attributable to the variation in attitude towards nuclear power and concern about nuclear accidents. In the case of older people, interest was also a factor. Young people were not as interested in the issue. The most important factor in determining the attitude towards a final repository was the benefit it was expected to bring to the municipality. Moral and emotional aspects were also important. Risk played a relatively subordinate role. Social aspects were very important: those who frequently spoke with people who were positively disposed tended to be positive themselves, and vice versa for those who were negative. This factor could explain some of the gender differences in attitude. Attitudes in Oskarshamn were slightly more positive than in Oesthammar, probably due to the fact that the residents in Oskarshamn had a greater sense of participation in the municipality's decision in the matter. Information from SKB was also found to be an important factor for the differences in attitude between the municipalities. Eight percentage points more people had received information in Oskarshamn than in Oesthammar. The difference may be small, but it exists and does appear to be of some importance. Attitudes in Oskarshamn and Oesthammar continued to be much more

Rock grouting. Current competence and development for the final repository

International Nuclear Information System (INIS)

Emmelin, Ann; Brantberger, Martin; Eriksson, Magnus; Gustafson, Gunnar; St ille, Haakan

2007-06-01

The report aims at presenting the overall state of grouting competence and development relating to the final repository and at motivating and giving detail to the grouting sections presented in the 2007 version of the overall SKB report 'Programme for research, development and demonstration of methods for the management and disposal of nuclear waste' that is presented to the government every three years. The report offers suggestions for principles for planning, design and execution of grouting and describes the further work thought to be necessary in order to meet the requirements of the final repository, that are currently given as working premises. This report does not aim to, and cannot, describe the grouting processes in detail. For details of current concepts, experience and development work, a list of references is provided. In Chapter 2, the task of sealing the underground repository is examined and an overall approach presented. Although the requirements related to this task are preliminary, it is made evident that they concern both the actual grouting results and the process leading to the achievement of these results. Chapter 3 is a conceptual description of grouting and the factors that govern the spreading of grout in the rock mass. It is intended as an introduction to Chapters 4-6, which describe the state of grouting competence and the tools available for the sealing of the final repository facility. Both common practice and cutting-edge research are dealt with in these chapters, mainly relying on references where available. Chapters 4 and 5 focus on the system consisting of the fundamental components the rock mass, the grout materials and the grouting technology, and how these system components interact whilst, in Chapter 6, the rock/grout technical system is viewed in a brief organizational context. Based on the requirements on results and the overall grouting process on the one hand and the current competence in grouting theory and practice on the

Rock grouting. Current competence and development for the final repository

Energy Technology Data Exchange (ETDEWEB)

Emmelin, Ann (Swedish Nuclear Fuel and Waste Management Co., Stockholm (SE)); Brantberger, Martin (Ramboell (SE)); Eriksson, Magnus (Vattenfall Power Consultant (SE)); Gustafson, Gunnar (Chalmers Univ. of Technology, Goeteborg (SE)); Stille, Haakan (Royal Inst. of Technology, Stockholm (SE))

2007-06-15

The report aims at presenting the overall state of grouting competence and development relating to the final repository and at motivating and giving detail to the grouting sections presented in the 2007 version of the overall SKB report 'Programme for research, development and demonstration of methods for the management and disposal of nuclear waste' that is presented to the government every three years. The report offers suggestions for principles for planning, design and execution of grouting and describes the further work thought to be necessary in order to meet the requirements of the final repository, that are currently given as working premises. This report does not aim to, and cannot, describe the grouting processes in detail. For details of current concepts, experience and development work, a list of references is provided. In Chapter 2, the task of sealing the underground repository is examined and an overall approach presented. Although the requirements related to this task are preliminary, it is made evident that they concern both the actual grouting results and the process leading to the achievement of these results. Chapter 3 is a conceptual description of grouting and the factors that govern the spreading of grout in the rock mass. It is intended as an introduction to Chapters 4-6, which describe the state of grouting competence and the tools available for the sealing of the final repository facility. Both common practice and cutting-edge research are dealt with in these chapters, mainly relying on references where available. Chapters 4 and 5 focus on the system consisting of the fundamental components the rock mass, the grout materials and the grouting technology, and how these system components interact whilst, in Chapter 6, the rock/grout technical system is viewed in a brief organizational context. Based on the requirements on results and the overall grouting process on the one hand and the current competence in grouting theory and

Study of thermal-gradient-induced migration of brine inclusions in salt. Final report

International Nuclear Information System (INIS)

Olander, D.R.

1984-08-01

Natural salt deposits, which are being considered for high-level waste disposal, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine (the all-liquid inclusions) migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms, which is undesirable. Therefore it is important to consider the migration of brine inclusions in salt under imposed temperature gradients to properly evaluate the performance of a future salt repository for nuclear wastes. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is nonlinear. At high axial loads, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, helium, air and argon were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large-ange grain boundaries was observed

Study of thermal-gradient-induced migration of brine inclusions in salt. Final report

Energy Technology Data Exchange (ETDEWEB)

Olander, D.R.

1984-08-01

Natural salt deposits, which are being considered for high-level waste disposal, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine (the all-liquid inclusions) migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms, which is undesirable. Therefore it is important to consider the migration of brine inclusions in salt under imposed temperature gradients to properly evaluate the performance of a future salt repository for nuclear wastes. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is nonlinear. At high axial loads, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, helium, air and argon were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large-ange grain boundaries was observed.

Salt drying: a low-cost, simple and efficient method for storing plants in the field and preserving biological repositories for DNA diversity research.

Science.gov (United States)

Carrió, Elena; Rosselló, Josep A

2014-03-01

Although a variety of methods have been optimized for the collection and storage of plant specimens, most of these are not suited for field expeditions for a variety of logistic reasons. Drying specimens with silica gel in polyethylene bags is currently the standard for field-sampling methods that are suitable for subsequent DNA extraction. However, silica-gel repositories are not readily available in remote areas, and its use is not very cost-effective for the long-term storage of collections or in developing countries with limited research budgets. Salting is an ancient and traditional drying process that preserves food samples by dehydrating tissues and inhibiting water-dependent cellular metabolism. We compared salt and silica-gel drying methods with respect to dehydration rates overtime, DNA quality and polymerase chain reaction(PCR) success to assess whether dry salting can be used as an effective plant preservation method for DNA analysis. Specimens from eleven plant species covering a variety of leaf structures, leaf thicknesses and water contents were analysed. Experimental work indicated that (i) levels of dehydration in sodium chloride were usually comparable to those obtained when silica gel was used, (ii) no spoilage, fungal or bacterial growth was observed for any of the species with all drying treatments and (iii) good yields of quality genomic DNA suitable for PCR applications were obtained in the salt-drying treatments. The preservation of plant tissues in commercial table salt appears to be a satisfactory, and versatile method that may be suitable in remote areas where cryogenic resources and silica repositories are not available. © 2013 John Wiley & Sons Ltd.

Current status of geotechnical research on the long-term safety of permanent repositories for nuclear waste

International Nuclear Information System (INIS)

Langer, M.

1988-01-01

The planned permanent underground repository for non-heat-generating wastes in the former Konrad iron-ore mine is now in the final stages of the plan approval procedures. The deadline for the final stages of the plan approval procedures for the Gorleben salt dome is approaching. It is time to give an account of what has been accomplished in the geotechnical field. The BGR has developed a complex geotechnical stability analysis that takes into account the requirements of permanent storage and the objectives required for the protection of the biosphere. This stability analysis is based on the following considerations: Owing to the complexity of the boundary conditions, a cavity intended for a permanent repository can be demonstrated to be safe only by a combination of studies and simulations. These studies must integrate engineering geology, geotechnics, rock mechanics, statics, monitoring of the conditions in the repository, and mining expertise. (orig.) With 27 figs

Performance of high level waste forms and engineered barriers under repository conditions

International Nuclear Information System (INIS)

1991-02-01

The IAEA initiated in 1977 a co-ordinated research programme on the ''Evaluation of Solidified High-Level Waste Forms'' which was terminated in 1983. As there was a continuing need for international collaboration in research on solidified high-level waste form and spent fuel, the IAEA initiated a new programme in 1984. The new programme, besides including spent fuel and SYNROC, also placed greater emphasis on the effect of the engineered barriers of future repositories on the properties of the waste form. These engineered barriers included containers, overpacks, buffer and backfill materials etc. as components of the ''near-field'' of the repository. The Co-ordinated Research Programme on the Performance of High-Level Waste Forms and Engineered Barriers Under Repository Conditions had the objectives of promoting the exchange of information on the experience gained by different Member States in experimental performance data and technical model evaluation of solidified high level waste forms, components of the waste package and the complete waste management system under conditions relevant to final repository disposal. The programme includes studies on both irradiated spent fuel and glass and ceramic forms as the final solidified waste forms. The following topics were discussed: Leaching of vitrified high-level wastes, modelling of glass behaviour in clay, salt and granite repositories, environmental impacts of radionuclide release, synroc use for high--level waste solidification, leachate-rock interactions, spent fuel disposal in deep geologic repositories and radionuclide release mechanisms from various fuel types, radiolysis and selective leaching correlated with matrix alteration. Refs, figs and tabs

Disposal alternatives and recommendations for waste salt management for repository excavation in the Palo Duro Basin, Texas

International Nuclear Information System (INIS)

1987-01-01

This report documents an evaluation of five alternatives for the disposal of waste salt that would be generated by the construction of a repository for radioactive waste in underground salt deposits at either of two sites in the Palo Duro Basin, Texas. The alternatives include commercial disposal, offsite deep-well injection, disposal in abandoned mines, ocean disposal, and land surface disposal on or off the site. For each alternative a reference case was rated - positive, neutral, or negative - in terms of environmental and dependability factors developed specifically for Texas sites. The factors constituting the environmental checklist relate to water quality impact, water- and land-use conflicts, ecological compatibility, conformity with air quality standards, and aesthetic impact. Factors on the dependability check-list relate to public acceptance, the adequacy of site characterization, permit and licensing requirements, technological requirements, and operational availability. A comparison of the ratings yielded the following viable alternatives, in order of preference: (1) land surface disposal, specifically disposal on tailings piles associated with abandoned potash mines; (2) disposal in abandoned mines, specifically potash mines; and (3) commercial disposal. Approaches to the further study of these three salt management techniques are recommended

The HAW-Project. Test disposal of highly radioactive radiation sources in the Asse salt mine. Final report

International Nuclear Information System (INIS)

Rothfuchs, T.; Cuevas, C. de las; Donker, H.; Feddersen, H.K.; Garcia-Celma, A.; Gies, H.; Goreychi, M.; Graefe, V.; Heijdra, J.; Hente, B.; Jockwer, N.; LeMeur, R.; Moenig, J.; Mueller, K.; Prij, J.; Regulla, D.; Smailos, E.; Staupendahl, G.; Till, E.; Zankl, M.

1995-01-01

In order to improve the final concept for the disposal of high-level radioactive waste (HAW) in boreholes drilled into salt formation plans were developed a couple of years ago for a full scale testing of the complete technical system of an underground repository. To satisfy the test objectives, thirty highly radioactive radiation sources were planned to be emplaced in six boreholes located in two test galleries at the 800-m-level in the Asse salt mine. A duration of testing of approximately five years was envisaged. Because of licensing uncertainties the German Federal Government decided on December 3rd, 1992 to stop all activities for the preparation of the test disposal immediately. In the course of the preparation of the test disposal, however, a system, necessary for handling of the radiation sources was developed and installed in the Asse salt mine and two non-radioactive reference tests with electrical heaters were started in November 1988. These tests served for the investigation of thermal effects in comparison to the planned radioactive tests. An accompanying scientific investigation programme performed in situ and in the laboratory comprises the estimation and observation of the thermal, radiation-induced, and mechanical interaction between the rock salt and the electrical heaters and the radiation sources, respectively. The laboratory investigations are carried out at Braunschweig (FRG), Petten (NL), Saclay (F) and Barcelona (E). As a consequence of the premature termination of the project the working programme was revised. The new programme agreed to by the project partners included a controlled shutdown of the heater tests in 1993 and a continuation of the laboratory activities until the end of 1994. (orig.)

A review of in situ investigations in salt

International Nuclear Information System (INIS)

Kuehn, K.

1985-01-01

In situ investigations for the disposal of radioactive wastes in rock salt formations have the longest history in the field. Well known names are Project Salt Vault (PSV) which was performed in the Lyons Mine, Kansas/USA, and the Asse salt mine in Germany. The overall objective for in situ investigations is twofold: 1. To produce all necessary data for the construction and operation of repositories and 2. to produce all necessary data for a performance assessment for repositories

Technical and logistic provisions for the delivery of radioactive wastes in the final repository Konrad

International Nuclear Information System (INIS)

Poeppinghaus, Jens

2013-01-01

The beginning of radioactive waste delivery to the final repository Konrad is planned for 2019. The main issue for the technical and logistic provisions is the development of a concept for the transport of the licensed radioactive waste containers to the site, including a turning concept for cylindrical waste forms and planning, construction and manufacture of transport equipment. Further issues include a logistic concept considering specific boundary conditions as administrative processes, priorities, special features of the delivering institutions and technical requirements of the repository.

75 FR 56101 - Lauryl Sulfate Salts Registration Review Final Decision; Notice of Availability

Science.gov (United States)

2010-09-15

... decision for the pesticide, lauryl sulfate salts (also known as sodium lauryl salts), case 4061... announces the availability of EPA's final registration review decision for the lauryl sulfate salts. Sodium... product that contains sodium lauryl sulfate as an active ingredient. The product, Kleenex[reg] Brand...

Drafting of the closure of the Asse salt mine. Final report

International Nuclear Information System (INIS)

Schneefuss, J.U.

2001-01-01

The report of the R and D-project 'Drafting of the closure of the Asse salt mine' contains the results of the first phases 'Basic findings' and 'Predrafting'. These phases were started after the backfilling of the south flank of the Asse salt mine was permitted in accordance to 2.2 of the operating program 'Future work at the Asse salt mine'. The knowledge status of May 2000 is reported. The result obtained in this program provides the basis for future drafting the closure of the Asse salt mine. The final results will include the long-term safety assessment to obtain the permission of the mining authorities for the closure of the Asse salt mine. The evaluation of the basic data has shown that further investigations are necessary. During the predrafting period the method for backfilling of the cavities, transport of the backfill and backfill and closure of the shafts were developed. Other parts of the concept for the closure are not finalized (control of the brine inflow when starting backfilling above the 658-m-level, minimizing of the possible effects of dissolution of carnallitite, avoiding of squeezing brines from deeper cavities through the disposal chambers etc.). (orig.) [de

Rock quality designation of the hydraulic properties in the near field of a final repository for spent nuclear fuel

International Nuclear Information System (INIS)

Carlsson, Hans; Carlsson, Leif; Pusch, Roland

1989-06-01

Quality assurance of a final repository for spent nuclear fuel requires detailed information on the characteristics of the rock, backfill, canisters and the waste itself. Furthermore, and of fundamental importance, is the knowledge of the behaviour of the integrated system of the waste and the different barriers. The in-situ characteristics of the rock must therefore be assessed and their influence on and interactions with the remaining barriers must be predicted and verified. A rock quality designation process of the hydraulic properties in the near-field is out-lined both for the KBS-3 system as well as for the WP-cave system. The process, once updated and approved, will be included in a Quality Assurance Program for the final repository for spent nuclear fuel. Some of the available methods for the near-field designation process are presented as well as techniques that need further development or are not developed at all. Finally, a presentation is given of a generic designation process of the KBS-3 and WP-cave repository systems in the previously investigated area in Central Sweden, where the final repository for reactor waste, SFR, is located. Geological and hydrogeological data are here at hand and it is therefore possible to carry out a simulation of how the designation process would be accomplished. (authors) (72 figs., 12 tabs., 43 refs.)

Assessments of the thermal evolution for a radioactive waste final repository using analytical methods

International Nuclear Information System (INIS)

Radut, A. C.; Roman, M. R.; Florea, S.; Ionescu, D. V.; Olteanu, G.; Valeca, S.

2016-01-01

In the designing process for a radioactive final repository concept, the temperature evolution over time is a significant issue for the stability and long-term safety of entire emplacement. In particular, the maximum value of temperature in the whole structure, during time, must not exceed a certain safety value which depends, beside other criteria, on the bulk material of the repository. A computer code TEMPROC, based on analytical model for the transient thermal heat conduction, described in this paper, was developed inside ''Fuel Performance''Department from ICN Pitesti, in order to evaluate the waste repository's temperature distribution. The program was developed under ''Microsoft FORTRAN Power Station''platform that provides IMSL subroutines library support for numeric algorithm. So the program is relative small, with a good calculus speed. The numerical results obtained with TEMPROC computer code, have been acceptably compared with similar existing data from scientific literature [1]. (authors)

Monitoring as component for the decision making in final repository projects; Monitoring als Baustein fuer die Entscheidungsfindung in Endlagerprojekten

Energy Technology Data Exchange (ETDEWEB)

Kallenbach-Herbert, Beate; Alt, Stefan [Oeko-Institut e.V., Darmstadt (Germany)

2012-12-15

The monitoring in final radioactive waste repositories is performed by continuous or repeated measurements of technical and geologic parameters during long time periods. The collected data serve manifold purposes. The central focus is to provide fundamental information for the decision between and within the three phases of a final repository project. This means that monitoring is not only the sum of technical surveillance measures. Monitoring is also important for several sociopolitical decisions, for instance in case of closure of the repository. The article discusses possible objectives and shows the relevant technical aspects that are used deduce the requirements for an integrated monitoring concept. It is shown that a monitoring concept should be developed early enough involving all groups that are concerned by the waste disposal project.

Comments on US approach to backfilling: Thermochemical characterization of crushed salt

International Nuclear Information System (INIS)

Smith, S.; Hume, H.

1988-01-01

From recent studies and calculations, it has become apparent that expected brine in a United States salt repository would not seriously detract from the usefulness of rock salt as backfill. It also has been shown that adding clay to the salt might add to the pressure on the emplaced waste packages. Nevertheless, the Salt Repository Project has planned to evaluate a betonite/salt mixture during the next few years. The following items have also been discussed: advantages of backfilling, variables affecting crushed salt behavior, and the general approach to a preliminary testing program

Chemical modeling of nuclear waste repositories in the salt repository project

International Nuclear Information System (INIS)

Jansen, G.; Raines, G.E.; Kircher, J.F.; Hubbard, N.

1985-01-01

Salt deposits contain small amounts of water as brine in fluid inclusions in halite and in hydrous minerals, e.g., clays, kieserite (MgSO 4 . H 2 O) and carnallite (KMgCl 3 . 6H 2 O). For the candidate salt deposits, the total amounts of water as volume % brine are: Palo Duro Basin, Texas, approximately 1.8; Paradox Basin, Utah, approximately 5.0 for the carnallite-marker zone, and less than approximately 0.5 below this zone; Gulf Coast salt domes, less than 0.15. For the Palo Duro and Paradox salt, the brines are Mg-rich (approximately 20,000 mg/L to approximately 100,000 mg/L) and sometimes Ca-rich (up to about 20,000 mg/L) NaCl brines. Brine migration calculations have been made using calculations of the time-variant thermal gradient around the waste packages and conservatively high brine volumes in the salt (5.0 volume % for the Texas and Utah sites and 0.5 volume % for the Gulf Coast) as input data. The maximum amounts of brine that eventually migrate to each waste package are about 1.0m 3 (for 5.0 volume % brine) and 0.2m 3 (for 0.5 volume % brine). With current conceptual designs for waste package overpacks (10 to 15 cm thick low-carbon steel), the waste package is not breached by uniform corrosion within 10,000 years. In brines this material thus far shows only uniform corrosion. For the expected conditions, where the brine is provided solely by brine migration, the brine is consumed by reaction with the iron of the overpack nearly as fast as it migrates to the waste package. Therefore, for the expected conditions, data about corrosion rates, radiolysis, etc., are not important. However, it is essential that accurate volumes of in-migrating brine can be calculated

Salt Repository Project site study plan for stratigraphic boreholes: Revision 1, December 18, 1987

International Nuclear Information System (INIS)

1987-01-01

This site study describes the Stratigraphic Boreholes field work to be conducted during the early stages of Site Characterization at the Deaf Smith County, Texas site. The field program has been designed to provide data useful in addressing information/data needs resulting from Federal/State/local regulations, and repository program requirements. Four Stratigraphic Holes will be drilled near the perimeter of the site to document the subsurface geologic conditions in that area and to provide data necessary for design and construction of the Exploratory Shaft Facilities. Continuous samples will be recovered from the ground surface to the total depth of each sell. Geophysical well logs will provide additional coverage of the stratigraphic section. In-situ down hole testing will include short term hydrologic tests and hydraulic fracture tests to provide information on deep groundwater characteristics and regional stress patterns, respectively. Field methods/tests are chosen that provide the best or only means of obtaining the required data. The Salt Repository Project (SRP) Networks specify the schedule which the program will operate. The Technical Services Contractor is responsible for conducting the field program of drilling and testing. Samples and data will be handled and reported in accordance with established SRP procedures. A quality assurance program will be utilized to assure that activities affecting quality are performed correctly and that the appropriate documentation is maintained. 30 refs., 13 figs., 4 tabs

Site study plan for Playa investigations, Deaf Smith County, Texas: Salt Repository Project

International Nuclear Information System (INIS)

1987-01-01

This plan defines the purpose and objectives of the Playa Investigation Study, presents a plan of work to provide the information necessary to resolve issues, and discusses the rationale for test method selection. The required information will be obtained from existing well drilling records, describing and testing of soil and rock samples recovered from project test holes, geophysical well logs, seismic surveys, and shallow test pits excavated at ground surface. There have been numerous, often conflicting, theories presented to explain the origin(s) of the playas of the Texas High Plains. The primary purpose of this study is to establish if existing playas and playa alignments are related to deeper subsurface structure, such as faulting or salt dissolution, the potential for future playa development, and the significance of existing and/or future playas on siting a repository in Deaf Smith County, Texas. 11 refs

Conceptual design of repository facilities

International Nuclear Information System (INIS)

Beale, H.; Engelmann, H.J.; Souquet, G.; Mayence, M.; Hamstra, J.

1980-01-01

As part of the European Economic Communities programme of research into underground disposal of radioactive wastes repository design studies have been carried out for application in salt deposits, argillaceous formations and crystalline rocks. In this paper the design aspects of repositories are reviewed and conceptual designs are presented in relation to the geological formations under consideration. Emphasis has been placed on the disposal of vitrified high level radioactive wastes although consideration has been given to other categories of radioactive waste

Investigations on backfilling and sealing of chambers and shafts in a final salt repository

International Nuclear Information System (INIS)

Glaess, F.; Kappei, G.; Schmidt, M.W.; Schwieger, K.; Starke, C.; Taubert, E.; Wallmueller, R.; Walter, F.; Tischle, N.R.; Haensel, W.; Meyer, T.

1991-03-01

Soil mechanical laboratory investigations as well as geotechnical in situ measurements were carried out. The laboratory tests provided important information on the material behaviour of selected backfill and sealing materials. Initial conclusions on the long-term behaviour of backfill and seals as well as on their interaction with the rock were gained with the results of in situ measurements in backfilled chambers and seals and in the surrounding rock of the Asse salt mine. (orig./DG) [de

Shaft seals for final high-level radioactive waste repositories. ELSA. Pt. 1; Schachtverschluesse fuer Endlager fuer hochradioaktive Abfaelle. ELSA. T. 1

Energy Technology Data Exchange (ETDEWEB)

Kudla, W.; Schreiter, F.; Gruner, M. [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Bergbau und Spezialtiefbau; Jobmann, M.; Bollingerfehr, W.; Mueller-Hoeppe, N.; Herold, P. [DBE Technology GmbH, Peine (Germany)

2013-04-30

The state of the art in science and technology fir shaft seals with long-term stability is summarized regarding their applicability for high-level waste repository in Germany. The concepts and drafts for the shaft sealing systems ERAM, Asse, Konrad, the WIPP side, the RESEAL concept, the NAGRA concept and the project LASA are reviewed. The methodology of applying partial factors in a safety analysis is summarized and the applicability of this method for geotechnical sealing structures is confirmed. To establish geomechanical boundary conditions of the host rocks and clay stone the stress-strain behavior of the rock mass adjoining the shaft has to be identified including time-dependent thermo-mechanical processes. The general and special requirements for the design of shaft sealing systems, especially in salt rock and clay formations are described, derived from the safety requirements (BMU 2010). Finally general information needs were identified.

2008 annual meeting on nuclear technology: topical sessions. Pt. 2. Construction of the final repository KONRAD

International Nuclear Information System (INIS)

Broeskamp, H.

2008-01-01

Summary report by Dipl.-Ing. Holger Broeskamp on the Topical Session ''Constructing the Final Repository KONRAD'' of the Annual Conference on Nuclear Technology held in Hamburg, May 27-29, 2008. (orig.)

Operational experience from SFR - Final repository for low- and intermediate level waste in Sweden

International Nuclear Information System (INIS)

Skogsberg, Marie; Ingvarsson, Roger

2006-01-01

SFR, the Swedish Final Repository for Radioactive Waste, has been in operation since April 1988. It was designed for short lived LLW/ILW from the operation and maintenance of all Swedish Nuclear Power Plants. The first stage was constructed for 63 000 m 3 which was assumed to give a margin and flexibility for the preliminary operational period. Today this volume represents the whole prediction of operational waste. Until the end of 2005 SFR has received 30 930 m 3 waste. In average it has been 2-3 derivations per year at the repository. The most derivations happened in the years 1993-1995, and that was also the years when the repository received the most volume of waste. The most of the derivations those years was related to the waste packages. The dose rate to the personal has always been very low in the latest years the collective dose has been under 0,1 mmanSv/year. (author)

Radioactive waste isolation in salt: peer review of the Office of Nuclear Waste Isolation's report on Functional Design Criteria for a Repository for High-Level Radioactive Waste

International Nuclear Information System (INIS)

Hambley, D.F.; Russell, J.E.; Busch, J.S.; Harrison, W.; Edgar, D.E.; Tisue, M.W.

1984-08-01

This report summarizes Argonne's review of the Office of Nuclear Waste Isolation's (ONWI's) draft report entitled Functional Design Criteria for High-Level Nuclear Waste Repository in Salt, dated January 23, 1984. Recommendations are given for improving the ONWI draft report

Areal thermal loading recommendations for nuclear waste repositories in salt

International Nuclear Information System (INIS)

Russell, J.E.

1979-06-01

This document gives a wider understanding of the history of the recommended thermal loadings in salt for both high-level waste (HLW) from fresh UO 2 -fueled, light-water reactors (LWR) with no recycle and spent unreprocessed fuel (SURF) from LWRs. Aspects of the current recommendations that need further study are identified. Finally, an interim set of design thermal-loading recommendations are given that have a common rationale of satisfying performance limits within our current state of knowledge. These recommendations are made on a generic rather than a site-specific basis. 11 figures, 5 tables

Status and future developments of risk analysis for repositories of radioactive wastes in salt formations in the Federal Republic of Germany

International Nuclear Information System (INIS)

Proske, R.

1977-01-01

In the Federal Republic of Germany a hypothetical repository for High-Level Radioactive Waste in a salt formation was taken as basis for a first attempt to use the methodology of risk analysis in order to get statements on the safety of such a geologic and mining system. Several institutions were engaged in drawing up fault trees, development of release models and calculation of the risk. A lot of R+D-work is scheduled to be carried out in future which includes optimization of the application of risk analysis methodology to geologic and mining systems, further development of release models, development of a model describing the migration of radionuclides in typical geologic strata and soils of the Federal Republic of Germany and application of risk analysis methodology to different repositories and disposal technologies

Project Guarantee 1985. Radioactive wastes: Properties and allocation to final repository types

International Nuclear Information System (INIS)

Anon.

1985-01-01

An overview of waste-specific data, as input into constructional engineering studies and safety analyses of Project Guarantee, is presented which describes the activity inventory of the radioactive waste to be disposed of, classified according to origin, the quantitative spezifications of the waste, the concept of classifying waste into appropriate categories, grouping into major categories and distribution of these between the different repository types, and finally, control measures which ensure observance of the specifications of the waste to be disposed of. It is expedient, for conceptional considerations and for the operational phase of the repository, to split the waste up into several suitably specified waste categories according to the practical aspects of origin and conditioning. This can be done in such a way that the waste within a specific category is sufficiently homogeneous with regard to its radiological properties and chemical composition for the requirements of safety analysis. The present volume contains base-data for around 30 waste types. Two waste types are documented with more detailed data as an example of the practicability of the comprehensive waste characterisation contained in reference report NTB 84-47. It is shown that waste-specific data which go into safety analysis and constructional engineering project studies are available in an appropriate degree of detail. The method of distributing the waste between repositories with differing degrees of protection and procedures for controlling adherence to admission specifications are developed and documented. It can be ensured that no waste with an impermissibly high radiotoxicity level will later be emplaced in a repository for low- and intermediate-level waste

Postclosure risks of alternative SRP nuclear waste forms in geologic repositories

International Nuclear Information System (INIS)

Cheung, H.; Edwards, L.; Harvey, T.; Revelli, M.

1982-05-01

The postclosure risk of REFERENCE and ALTERNATIVE waste forms for the defense high-level waste at the Savannah River Plant (SRP) were compared by analyses with a computer code, MISER, written to study the effects of repository features in a probabilistic framework. MISER traces radionuclide flows through a network of stream tubes from the repository to risk-sensitive points. Uncertainties in waste form, package properties, and geotechnical data are accounted for with Monte Carlo techniques. Our results show: (1) for generic layered-salt and basalt repositories, the difference in performance between the two waste forms is insignificant; (2) where the doses are sensitive to uncertainties in leaching rates, the doses are orders of magnitude below background; (3) disruptive events contribute only slightly to the risk of a layered-salt repository; (4) simple design alterations have strong effects on near field doses; (5) great care should be exercised in selecting the location at which repository risks are to be measured, calculated, or regulated

Long-term environmental impacts of geologic repositories

International Nuclear Information System (INIS)

Pigford, T.H.

1983-05-01

This paper summarizes a study of the long-term environmental impacts of geologic repositories for radioactive wastes. Conceptual repositories in basalt, granite, salt, and tuff were considered. Site-specific hydrological and geochemical parameters were used wherever possible, supplemented with generic parameters when necessary. Radiation doses to future maximally exposed individuals who use the contaminated groundwater and surface water were calculated and compared with a performance criterion of 10 -4 Sv/yr for radiation exposures from probable events. The major contributors to geologic isolation are the absence of groundwater if the repository is in natural salt, the slow dissolution of key radioelements as limited by solubility and by diffusion and convection in groundwater, long water travel times from the waste to the environment, and sorption retardation in the media surrounding the repository. In addition, dilution by surface water can considerably reduce the radiation exposures that result from the small fraction of the waste radioactivity that may ultimately reach the environment. Estimates of environmental impacts are made both for unreprocessed spent fuel and for reprocessing wastes. Accelerated dissolution of waste exposed to groundwater during the period of repository heating is also considered. This study of environmental impacts is a portion of a more comprehensive study of geologic waste disposal carried out by the Waste Isolation System Panel of the US National Research Council

IRIS Toxicological Review of Hydrogen Cyanide and Cyanide Salts (Final Report)

Science.gov (United States)

EPA has finalized the Toxicological Review of Hydrogen Cyanide and Cyanide Salts: in support of the Integrated Risk Information System (IRIS). Now final, this assessment may be used by EPA’s program and regional offices to inform decisions to protect human health.

Review of geotechnical measurement techniques for a nuclear waste repository in bedded salt

International Nuclear Information System (INIS)

1979-12-01

This report presents a description of geotechnical measurement techniques that can provide the data necessary for safe development - i.e., location, design, construction, operation, decommissioning and abandonment - of a radioactive waste repository in bedded salt. Geotechnical data obtained by a diversity of measurement techniques are required during all phases of respository evolution. The techniques discussed in this report are grouped in the following categories: geologic, geophysical and geodetic; rock mechanics; hydrologic, hydrogeologic and water quality; and thermal. The major contribution of the report is the presentation of extensive tables that provide a review of available measurement techniques for each of these categories. The techniques are also discussed in the text to the extent necessary to describe the measurements and associated instruments, and to evaluate the applicability or limitations of the method. More detailed discussions of thermal phenomena, creep laws and geophysical methods are contained in the appendices; references to detailed explanations of measurement techniques and instrumentation are inluded throughout the report

Review of geotechnical measurement techniques for a nuclear waste repository in bedded salt

Energy Technology Data Exchange (ETDEWEB)

1979-12-01

This report presents a description of geotechnical measurement techniques that can provide the data necessary for safe development - i.e., location, design, construction, operation, decommissioning and abandonment - of a radioactive waste repository in bedded salt. Geotechnical data obtained by a diversity of measurement techniques are required during all phases of respository evolution. The techniques discussed in this report are grouped in the following categories: geologic, geophysical and geodetic; rock mechanics; hydrologic, hydrogeologic and water quality; and thermal. The major contribution of the report is the presentation of extensive tables that provide a review of available measurement techniques for each of these categories. The techniques are also discussed in the text to the extent necessary to describe the measurements and associated instruments, and to evaluate the applicability or limitations of the method. More detailed discussions of thermal phenomena, creep laws and geophysical methods are contained in the appendices; references to detailed explanations of measurement techniques and instrumentation are inluded throughout the report.

Modeling the dissolution behavior of defense waste glass in a salt repository environment

International Nuclear Information System (INIS)

McGrain, B.P.

1988-02-01

A mechanistic model describing a dynamic mass balance between the production and consumption of dissolved silica was found to describe the dissolution behavior of SRL-165 defense waste glass in a high-magnesium brine (PBB3) at a temperature of 90 0 C. The synergistic effect of the waste package container on the glass dissolution rate was found to depend on a precipitation reaction for a ferrous silicate mineral. The model predicted that the ferrous silicate precipitate should be variable in composition where the iron/silica stoichiometry depended on the metal/glass surface area ratio used in the experiment. This prediction was confirmed experimentally by the variable iron/silica ratios observed in filtered leachates. However, the interaction between dissolved silica and iron corrosion products needs to be much better understood before the model can be used with confidence in predicting radionuclide release rates for a salt repository. 25 refs., 4 figs., 1 tab

Statement of J.O. Neff, Manager, Salt Repository Project Office, Department of Energy

International Nuclear Information System (INIS)

Anon.

1987-01-01

My name is Jeff Neff and I am the Manager of the US Department of Energy's Salt Repository Project Office, now located in Hereford, Texas. The responsibilities of my office are to manage the day-to-day activities of the site suitability investigations of the designated nine-square-mile site located in Deaf Smith County, near Hereford in the Texas Panhandle. The location is indicated on several of the attachments. My remarks will be divided into five categories: (1) a brief history of how the Deaf Smith County site was designated; (2) a review of major issues for the Texas site and how these are expected to be resolved during site characterization; (3) a summary of major institutional issues; (4) a summary of consultation and cooperation activities with the State of Texas, through its Nuclear Waste Programs Office; and (5) highlights of current and past interactions with local governmental officials and the public in the Panhandle

VerSi - A Methodology for a Comparison of Potential Repository Sites

International Nuclear Information System (INIS)

Hund, Wilhelm

2010-09-01

In the year 2000 the moratorium on the exploration of the Gorleben salt dome as a potential repository for all kinds of radioactive waste became effective as a result of the consensus agreement between the Federal Government and the utilities about phasing out nuclear energy in Germany. All exploration activities were interrupted for at maximum ten years to clarify conceptual and safety relevant questions. A new set of safety requirements for the final disposal of heat-generating radioactive waste in deep geological formations was established in July 2009 by the Federal Ministry for the Environment, Nature Conservation and Nuclear Safety (BMU). As the BMU intended to carry out a comparison of potential repository sites it was necessary to initiate the development of a methodology for the identification of the site with the highest level of safety. A comparison of different repository sites requires a tool ensuring most confident and objective criteria for the comparison, whereas up to present long-term safety analyses were focused on confirming the suitability of sites by meeting the protection objectives by the measures of dose and risk. Within the 2006 established project VerSi a methodology for comparing different sites in different host rocks will be developed on the basis of long-term safety analyses taking into account geoscientific databases, inventory of radioactive waste, waste containers, corresponding disposal concepts and the feasibility of appropriate backfilling and closure concepts. The development of the method is aiming at providing measures other than dose and risk for the evaluation of the level of safety. For testing the tools a HLW-repository hosted in a salt dome (Gorleben) will be compared with a generic HLW-repository in consolidated clay as a host rock. As until now in Germany no clay stone site has been investigated for hosting a HLW repository, the required data are transferred from international research projects and repository concepts

Conceptual waste package interim product specifications and data requirements for disposal of borosilicate glass defense high-level waste forms in salt geologic repositories

International Nuclear Information System (INIS)

1983-06-01

The conceptual waste package interim product specifications and data requirements presented are applicable specifically to the normal borosilicate glass product of the Defense Waste Processing Facility (DWPF). They provide preliminary numerical values for the defense high-level waste form parameters and properties identified in the waste form performance specification for geologic isolation in salt repositories. Subject areas treated include containment and isolation, operational period safety, criticality control, waste form/production canister identification, and waste package performance testing requirements. This document was generated for use in the development of conceptual waste package designs in salt. It will be revised as additional data, analyses, and regulatory requirements become available

Conceptual waste package interim product specifications and data requirements for disposal of glass commercial high-level waste forms in salt geologic repositories

International Nuclear Information System (INIS)

1983-10-01

The conceptual waste package interim product specifications and data requirements presented are applicable to the reference glass composition described in PNL-3838 and carbon steel canister described in ONWI-438. They provide preliminary numerical values for the commercial high-level waste form parameters and properties identified in the waste form performance specification for geologic isolation in salt repositories. Subject areas treated include containment and isolation, operational period safety, criticality control, waste form/production canister identification, and waste package performance testing requirements. This document was generated for use in the development of conceptual waste package designs in salt. It will be revised as additional data, analyses and regulatory requirements become available. 13 references, 1 figure

Final repository for spent nuclear fuel - the role of the municipality

International Nuclear Information System (INIS)

Berggren, Marie; Lindfors, Virpi; Andersson Oehrn, Barbro; Alm, Bertil; Soederblom, Anna-Lena; Berggren, Marie; Lindfors, Virpi

2014-01-01

In Sweden there is a long tradition of local self-government which is enshrined within the Swedish constitution, and the municipalities are responsible for matters relating to its inhabitants and their immediate environment. The municipality of Oesthammar has been engaged in the project of final repository for spent nuclear fuel since 1995 and by that time a consultative committee was established with representatives from all the political parties within the municipality and neighbouring municipalities. Future potentials as well as threats must be considered when making decisions on the most favourable site and the method used for the disposal of nuclear waste, and the application from SKB, as well as the review by the authorities, must stand up to a number of public demands. The work has included several stages of decisions for the municipality, due to the site selection process for SKB. The dialogue between the municipality and SKB as well as between the municipality and the authorities has been of great importance for getting the stepwise decision making process that has become practice in this question. The municipality has intensively followed the process concerning establishment of a final repository through consultation meetings, by being observer on meetings between SKB and Swedish Radiation Safety Authority (SSM), seminars, statements, etc. The openness and transparency throughout the process has been essential between all actors. However, if the municipalities have a right of absolute veto, the government still can say yes even if the municipality has said no

Final report on decommissioning boreholes and wellsite restoration, Gulf Coast Interior Salt Domes of Mississippi

International Nuclear Information System (INIS)

1989-04-01

In 1978, eight salt domes in Texas, Louisiana, and Mississippi were identified for study as potential locations for a nuclear waste repository as part of the National Waste Terminal Storage (NWTS) program. Three domes were selected in Mississippi for ''area characterization'' phase study as follows: Lampton Dome near Columbia, Cypress Creek Dome near New Augusta, and Richton Dome near Richton. The purpose of the studies was to acquire geologic and geohydrologic information from shallow and deep drilling investigations to enable selection of sites suitable for more intensive study. Eleven deep well sites were selected for multiple-well installations to acquire information on the lithologic and hydraulic properties of regional aquifers. In 1986, the Gulf Coast salt domes were eliminated from further consideration for repository development by the selection of three candidate sites in other regions of the country. In 1987, well plugging and restoration of these deferred sites became a closeout activity. The primary objectives of this activity are to plug and abandon all wells and boreholes in accordance with state regulations, restore all drilling sites to as near original condition as feasible, and convey to landowners any wells on their property that they choose to maintain. This report describes the activities undertaken to accomplish these objectives, as outlines in Activity Plan 1--2, ''Activity Plan for Well Plugging and Site Restoration of Test Hole Sites in Mississippi.''

Determination of soil mechanics of salt rock as a potential backfilling material in an underground repository

International Nuclear Information System (INIS)

Kappei, G.

1987-09-01

Within the framework of the research and development project 'Backfilling and sealing of boreholes, chambers and roadways in a final dump', the Institute for Underground Dumping chose - from the broad range of possible stowing materials - the material 'salt spoil' and investigated its soil-mechanical properties in detail. Besides the implementation of soil-mechanical standard analyses (determination of the grain size distribution, bulk density, limits of storage density, proctor density, permeabilities, and shear strength) of two selected salt spoils (heap salt and rock salt spoil), the studies concentrated on the determination of the compression behaviour of salt spoil. In order to obtain data on the compaction behaviour of this material in the case of increasing stress, compression tests with obstructed lateral expansion were carried out on a series of spoil samples differing mainly in the composition of grain sizes. In addition to this, for a small number of samples of rock salt spoil, the creep behaviour at constant stress was determined after the compaction phase. (orig./RB) [de

Final repository for spent nuclear fuel. Underground design Simpevarp, Layout D1

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-04-15

This report is a compilation of the results of the underground design work carried out in design phase D1 of the Repository Design Project within the Deep Repository Project for the Simpevarp site. Similar reports are also being produced for the Laxemar and Forsmark sites. The design phase coincides with the initial site investigation phase. The main purpose of phase D1 is to answer the question 'Can a final repository be accommodated within the designated site', but also to test the design methodology and provide feedback to the modelling project. Design was carried out in accordance with the methodology described in UDP (Underground Design Premises), SKB R-04-60, and was based on preliminary data from various disciplines in the site modelling project. The preliminary input data used were then cross-checked against data in the final Site Descriptive Model SDM v 1.2 and significant differences were integrated in the design work. The design results from each design topic were presented by the designer at presentation meetings for SKB's design management and the reviewers engaged by SKB for the specific topic. After the presentation meeting the designer wrote up the work reports for the topic in question. The work reports were then reviewed by SKB's review team. The results of the review were compiled in a statement that was submitted to the designer to be dealt with. In the statement the designer documented which comments were dealt with and how. This report is a compilation of the entire design phase D1 for Simpevarp. The 3D layout with coordinate lists for deposition holes and tunnels that was drawn to illustrate a possible layout was used in the Preliminary safety evaluation of the Simpevarp subarea and the hydro modelling of the Open Repository, both activities within the Deep Repository Project. According to current plans for the Swedish nuclear programme, the minimum required number of canister positions in the repository is estimated to be

Recommended new criteria for the selection of nuclear waste repository sites in Columbia River basalt and US Gulf Coast domed salt

International Nuclear Information System (INIS)

Steinborn, T.L.; Wagoner, J.L.; Qualheim, B.; Fitts, C.R.; Stetkar, R.E.; Turnbull, R.W.

1980-01-01

Screening criteria and specifications are recommended to aid in the evaluation of sites proposed for nuclear waste disposal in basalt and domed salt. The recommended new criteria proposed in this report are intended to supplement existing repository-related criteria for nuclear waste disposal. The existing criteria are contained in 10 CFR 60 sections which define siting criteria of the Nuclear Regulatory Commission (NRC), and ONWI 33(2) which defines siting criteria of the Office of Nuclear Waste Isolation (ONWI) for the Department of Energy. The specifications are conditions or parameter values that the authors recommend be applied in site acceptance evaluations. The siting concerns covered in this report include repository depth, host rock extent, seismic setting, structural and tectonic conditions, groundwater and rock geochemistry, volcanism, surface and subsurface hydrology, and socioeconomic issues, such as natural resources, land use, and population distribution

Permanent Disposal of Nuclear Waste in Salt

Science.gov (United States)

Hansen, F. D.

2016-12-01

Salt formations hold promise for eternal removal of nuclear waste from our biosphere. Germany and the United States have ample salt formations for this purpose, ranging from flat-bedded formations to geologically mature dome structures. Both nations are revisiting nuclear waste disposal options, accompanied by extensive collaboration on applied salt repository research, design, and operation. Salt formations provide isolation while geotechnical barriers reestablish impermeability after waste is placed in the geology. Between excavation and closure, physical, mechanical, thermal, chemical, and hydrological processes ensue. Salt response over a range of stress and temperature has been characterized for decades. Research practices employ refined test techniques and controls, which improve parameter assessment for features of the constitutive models. Extraordinary computational capabilities require exacting understanding of laboratory measurements and objective interpretation of modeling results. A repository for heat-generative nuclear waste provides an engineering challenge beyond common experience. Long-term evolution of the underground setting is precluded from direct observation or measurement. Therefore, analogues and modeling predictions are necessary to establish enduring safety functions. A strong case for granular salt reconsolidation and a focused research agenda support salt repository concepts that include safety-by-design. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. Author: F. D. Hansen, Sandia National Laboratories

Two-phase flow in a saliniferous final repository using the example of ERAM. Final report; Zweiphasenfluss in einem salinaren Endlager am Beispiel des ERAM. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Kock, Ingo; Frieling, Gerd; Navarro, Martin

2016-10-15

In the frame of the research project ZIESEL the GRS enhanced the state of science and technology for the realization and evaluation of long-term safety cases for the final deposition of radioactive wastes. The superior aim was the improved understanding of two-phase flow processes in a complex final repository system. The consideration of two-phase processes in modeling of final repository systems induces processes and effects that significantly affect the transport behavior of fluid and radionuclides. Two-phase processes include not only capillary pressures and relative permeabilities but also a basic competition of phases with respect to pore volume for storage and transport and density-driven vertical separation of phases. Basically seals have been shown to be essential for the system behavior because of their influence of the gas pressure dependent control function. The system behavior is also influences by the model geometry.

Salt geologic evaluation of the impact of cryogenic fissures and halokinetic deformation processes on the integrity of the geological barrier of the salt dome Gorleben

International Nuclear Information System (INIS)

Hammer, Joerg; Fleig, Stephanie; Mingerzahn, Gerhard

2012-07-01

In several salt domes of the area close to Hannover fissures were observed that might be caused by thermally induced fissure formation due to cold periods (cryogenic fissures). Comprehensive substantial-structural analyses are performed as an example for the salt dome Bokeloh with respect to genesis and transferability to the salt dome Gorleben. Based on recent structure-geological, mineralogical-geochemical and micro-paleontological studies and thermo-mechanical modeling a solely thermally induced fissure formation due to cold periods is unlikely for the salt dome Bokeloh. There is a direct relation between the genesis of the salt dome Bokeloh, its regional tectonic site and the fissure formation. Due to the completely different genesis and another regional-tectonic situation the existence of cryogenic fissures is excluded for the salt dome Gorleben. The salt-geologic and experimental studies on the deformation of anhydrite layers in salt domes are summarized and evaluated with respect to the long-term consequences for a potential final repository for high-level heat-generating radioactive waste in the salt dome Gorleben. The studies confirm the older BGR studies that anhydrite layers do not represent hydraulic potential ling-distance liquid paths.

Project Guarantee 1985. Final repository for low- and intermediate-level radioactive wastes: The system of safety barriers

International Nuclear Information System (INIS)

Anon.

1985-01-01

The safety barrier system for the type B repository for low- and intermediate-level waste is described. The barrier parameters which are relevant for safety analysis are quantified and associated error limits and data scatter are given. The aim of the report is to give a summary documentation of the safety analysis input data and their scientific background. For secure containment of radioactive waste safety barriers are used which effectively limit the release of radioactive material from the repository (release barriers) and effectively retard the entry of the original radioactive material into the biosphere (time barriers). In the case of low- and intermediate-level waste the technical safety barrier system comprises: waste solidification matrix (cement, bitumen and resin), immobilisation of the waste packages in containers using liquid cement, concrete repository containers, backfilling of remaining vacant storage space with special concrete, concrete lining of the repository caverns, sealing of access tunnels on final closure of the repository. Natural geological safety barriers - host rock and overlying formations - have the following important functions. Because of its stability, the host rock in the repository zone protects the technical safety barrier system from destruction caused by climatic effects and erosion for a sufficient length of time. It also provides for low water flow and favourable chemistry (reducing conditions)

Underground repository for radioactive wastes

International Nuclear Information System (INIS)

Cassibba, R.O.

1989-01-01

In the feasibility study for an underground repository in Argentina, the conceptual basis for the final disposal of high activity nuclear waste was set, as well as the biosphere isolation, according to the multiple barrier concept or to the engineering barrier system. As design limit, the container shall act as an engineering barrier, granting the isolation of the radionuclides for approximately 1000 years. The container for reprocessed and vitrified wastes shall have three metallic layers: a stainless steel inner layer, an external one of a metal to be selected and a thick intermediate lead layer preselected due to its good radiological protection and corrosion resistance. Therefore, the study of the lead corrosion behaviour in simulated media of an underground repository becomes necessary. Relevant parameters of the repository system such as temperature, pressure, water flux, variation in salt concentrations and oxidants supply shall be considered. At the same time, a study is necessary on the galvanic effect of lead coupled with different candidate metals for external layer of the container in the same experimental conditions. Also temporal evaluation about the engineering barrier system efficiency is presented in this thesis. It was considered the extrapolated results of corrosion rates and literature data about the other engineering barriers. Taking into account that corrosion is of a generalized type, the integrity of the lead shall be maintained for more than 1000 years and according to temporal evaluation, the multiple barrier concept shall retard the radionuclide dispersion to the biosphere for a period of time between 10 4 and 10 6 years. (Author) [es

Application of systems engineering to determine performance requirements for repository waste packages

International Nuclear Information System (INIS)

Aitken, E.A.; Stimmell, G.L.

1987-01-01

The waste package for a nuclear waste repository in salt must contribute substantially to the performance objectives defined by the Salt Repository Project (SRP) general requirements document governing disposal of high-level waste. The waste package is one of the engineered barriers providing containment. In establishing the performance requirements for a project focused on design and fabrication of the waste package, the systems engineering methodology has been used to translate the hierarchy requirements for the repository system to specific performance requirements for design and fabrication of the waste package, a subsystem of the repository. This activity is ongoing and requires a methodology that provides traceability and is capable of iteration as baseline requirements are refined or changed. The purpose of this summary is to describe the methodology being used and the way it can be applied to similar activities in the nuclear industry

Final repository for spent nuclear fuel. Underground design Forsmark, Layout D1

International Nuclear Information System (INIS)

Brantberger, Martin; Zetterqvist, Anders; Arnbjerg-Nielsen, Torben; Olsson, Tommy; Outters, Nils; Syrjaenen, Pauli

2006-04-01

This report comprises the design step D1 related to the underground design for a deep repository located at the Forsmark site. The design is based on the Site Descriptive Model Forsmark v1.2. All studies have been focussed at an area southeast of the Forsmark nuclear plant, which has been considered to be the most promising area for hosting the repository. SKB has developed guidelines for the design of the repository, which further describes the methodology applied for the studies. From these guidelines the following basic objectives for the design step D1 are summarized: to determine whether the final repository can be accommodated within the studied site; to identify site-specific facility critical issues; to test and evaluate the design methodology; to provide feedback to: the design organisation regarding additional studies that needs to be done; the site investigation and modelling organization regarding further investigations required; and the safety assessment team. The possible locations for a tentative deep repository are analysed in Chapter 3 of the report. The most promising area for the repository (denoted 'priority site') has been defined by SKB to be located southeast of the Forsmark nuclear plant and northwest of the gently dipping deformation zone ZFMNE00A2. Regarding the repository depth, present knowledge acquired from the site investigations indicates that it is possible to locate the repository at all stipulated depths according to SKB, that is between 400 m and 700 m depth. The preliminary assessment made in Chapter 3 clearly demonstrates that the repository can be accommodated within the 'priority site'. The potential to accommodate the repository is essentially the same for both 400 m and 500 m depths. The design of the deposition areas is reported in Chapter 4, which includes the design of layout features for all tunnels and deposition holes, orientation of tunnels, calculation of anticipated loss of deposition holes due to the applied

Final repository for spent nuclear fuel. Underground design Forsmark, Layout D1

Energy Technology Data Exchange (ETDEWEB)

Brantberger, Martin; Zetterqvist, Anders [Ramboell Sweden AB, Stockholm (Sweden); Arnbjerg-Nielsen, Torben [Ramboell Denmark A/S, Virum (Denmark); Olsson, Tommy [IandT Olsson AB, Uppsala (Sweden); Outters, Nils [Golder Associates AB, Uppsala (Sweden); Syrjaenen, Pauli [Gridpoint Oy, Helsinki (Sweden)

2006-04-15

This report comprises the design step D1 related to the underground design for a deep repository located at the Forsmark site. The design is based on the Site Descriptive Model Forsmark v1.2. All studies have been focussed at an area southeast of the Forsmark nuclear plant, which has been considered to be the most promising area for hosting the repository. SKB has developed guidelines for the design of the repository, which further describes the methodology applied for the studies. From these guidelines the following basic objectives for the design step D1 are summarized: to determine whether the final repository can be accommodated within the studied site; to identify site-specific facility critical issues; to test and evaluate the design methodology; to provide feedback to: the design organisation regarding additional studies that needs to be done; the site investigation and modelling organization regarding further investigations required; and the safety assessment team. The possible locations for a tentative deep repository are analysed in Chapter 3 of the report. The most promising area for the repository (denoted 'priority site') has been defined by SKB to be located southeast of the Forsmark nuclear plant and northwest of the gently dipping deformation zone ZFMNE00A2. Regarding the repository depth, present knowledge acquired from the site investigations indicates that it is possible to locate the repository at all stipulated depths according to SKB, that is between 400 m and 700 m depth. The preliminary assessment made in Chapter 3 clearly demonstrates that the repository can be accommodated within the 'priority site'. The potential to accommodate the repository is essentially the same for both 400 m and 500 m depths. The design of the deposition areas is reported in Chapter 4, which includes the design of layout features for all tunnels and deposition holes, orientation of tunnels, calculation of anticipated loss of deposition holes due

Prediction of temperature increases in a salt repository expected from the storage of spent fuel or high-level waste

International Nuclear Information System (INIS)

Llewellyn, G.H.

1978-04-01

Comparisons in temperature increases incurred from hypothetical storage of 133 MW of 10-year-old spent fuel (SF) or high-level waste (HLW) in underground salt formations have been made using the HEATING5 computer code. The comparisons are based on far-field homogenized models that cover areas of 65 and 25 sq miles for SF and HLW, respectively, and near-field unit-cell models covering respective areas of 610 ft 2 and 400 ft 2 . Preliminary comparisons based on heat loads of 150 kW/acre and 3.5 kW/canister indicated near-field temperature increases about 20% higher for the storage of the spent fuel than for the high-level waste. In these comparisons, it was also found that the thermal energy deposited in the salt after 500 years is about twice the energy deposited by the high-level waste. The thermal load in a repository containing 10-year-old spent fuel was thus limited to 60 kW/acre to obtain comparable far-field thermal effects as obtained in a repository containing 10-year-old high-level waste loaded at 150 kW/acre. Detailed far-field and unit-cell comparisons of transient temperature increases have been made based on these loadings. Unit-cell comparisons were made between a canister containing high-level waste with an initial heat production rate of 2.1 kW and a canister containing a PWR spent fuel assembly producing 0.55 kW. Using a three-dimensional unit-cell model, a maximum salt temperature increase of 260 0 F was calculated for the high-level waste prior to back-filling (5 years after burial), whereas a maximum temperature increase of 110 0 F was calculated for the spent fuel prior to backfilling (25 years after burial). Comparisons were also made between various configurational models for the high-level waste showing the applicability of each model

The industrial organization of the repository. Pitfall or logical?

International Nuclear Information System (INIS)

Frostenson, Magnus

2010-11-01

From a systems perspective the organization of the Swedish final repository project for nuclear waste is studied. Different aspects of organization are identified in the report, covering dimensions of geographical, operative, structural, responsibility and contextual organization. Following SKB's site selection for the applications for the final repository for spent nuclear system and the closing of the surplus value agreement, issues concerning operative, structural and contextual organization tend to become particularly pressing, which is reflected in three research questions: - How will the final repository project be organized operatively and structurally over time? - Why is the final repository project organized in this way by SKB? - What kind of contextual organization takes place in the final repository project and what are the consequences of these activities? How the different industrial units of the final repository project should be run and within which structure, for example concerning ownership and integration of units, is established in the report. SKB's reasons for choosing this kind of organization are also highlighted. Apart from legal and safety-related demands that must be met together with the demands of the owners, SKB's strategic preference for insourcing conditions organizational choices. The traditional task centred operative and structural organization of SKB is also reflected in the organizational choices for the present and future units of the final depository system. Contextual organization implies deepened actor relationships between SKB's owners and SKB on the one side and the municipalities Oesthammar and Oskarshamn on the other. Through active organizing, the final repository arena 'narrows down' and the final repository issue turns into an in many respects local issue. There is a clear tendency that the roles of SKB are multiplied in order to handle the demands that central stakeholders - in particular the municipalities - place on

Proceedings of the second international workshop on design and construction of final repositories

Energy Technology Data Exchange (ETDEWEB)

Simmons, G R

1995-11-01

Many international radioactive waste disposal programs are in the design and construction phases for underground laboratories and repositories. To provide a forum for discussion Svensk Kaernbraenslehantering AB (SKB) in 1992 initiated an international workshop series in which the organizations considering disposal in hard crystalline rock could meet to discuss issues relevant to The Design and Construction of Final Repositories. The first workshop with the theme `Excavation through water conducting major fracture zones` was hosted by SKB in Saestaholm, Sweden on 1993 March 30 to 31 and the workshop proceedings are SKB Technical Report 94-06. Atomic Energy of Canada Limited hosted the second workshop with the theme `Factors influencing repository design and layout` in Winnipeg, Canada on 1994 February 15 to 17. Thirty-eight people from organizations in eight countries and representative of the European Community participated in the Workshop. This report is the summary of the second workshop. The discussions at the Workshop were recorded and reproduced in the summary. Some editorial license was used to provide the text that follows. The participants were given the opportunity to comment on the text prior to publication. Unfortunately some individual speakers could not be identified on the recording of the Workshop discussions and are labelled `unidentified` in the text. (author).

Proceedings of the second international workshop on design and construction of final repositories

International Nuclear Information System (INIS)

Simmons, G.R.

1995-11-01

Many international radioactive waste disposal programs are in the design and construction phases for underground laboratories and repositories. To provide a forum for discussion Svensk Kaernbraenslehantering AB (SKB) in 1992 initiated an international workshop series in which the organizations considering disposal in hard crystalline rock could meet to discuss issues relevant to The Design and Construction of Final Repositories. The first workshop with the theme 'Excavation through water conducting major fracture zones' was hosted by SKB in Saestaholm, Sweden on 1993 March 30 to 31 and the workshop proceedings are SKB Technical Report 94-06. Atomic Energy of Canada Limited hosted the second workshop with the theme 'Factors influencing repository design and layout' in Winnipeg, Canada on 1994 February 15 to 17. Thirty-eight people from organizations in eight countries and representative of the European Community participated in the Workshop. This report is the summary of the second workshop. The discussions at the Workshop were recorded and reproduced in the summary. Some editorial license was used to provide the text that follows. The participants were given the opportunity to comment on the text prior to publication. Unfortunately some individual speakers could not be identified on the recording of the Workshop discussions and are labelled 'unidentified' in the text. (author)

Analysis on the use of engineered barriers for geologic isolation of spent fuel in a reference salt site repository

International Nuclear Information System (INIS)

Cloninger, M.O.; Cole, C.R.; Washburn, J.F.

1980-12-01

A perspective on the potential durability and effectiveness requirements for the waste form, container and other engineered barriers for geologic disposal of spent nuclear fuel has been developed. This perspective is based on calculated potential doses to individuals who may be exposed to radioactivity released from a repository via a groundwater transport pathway. These potential dose commitments were calculated with an integrated geosphere transport and bioshpere transport model. A sensitivity analysis was accomplished by varying four important system parameters, namely the waste radionuclide release rate from the repository, the delay prior to groundwater contact with the waste (leach initiation), aquifer flow velocity and flow path length. The nuclide retarding capacity of the geologic media, a major determinant of the isolation effectiveness, was not varied as a parameter but was held constant for a particular reference site. This analysis is limited to looking only at engineered barriers whose net effect is either to delay groundwater contact with the waste form or to limit the rate of release of radionuclides into the groundwater once contact has occurred. The analysis considers only leach incident scenarios, including a water well intrusion into the groundwater near a repository, but does not consider other human intrusion events or catastrophic events. The analysis has so far been applied to a reference salt site repository system and conclusions are presented.Basically, in nearly all cases, the regional geology is the most effective barrier to release of radionuclides to the biosphere; however, for long-lived isotopes of carbon, technetium and iodine, which were poorly sorbed on the geologic media, the geology is not very effective once a leach incident is initiated

Experiments and Modeling in Support of Generic Salt Repository Science

International Nuclear Information System (INIS)

Bourret, Suzanne Michelle; Stauffer, Philip H.; Weaver, Douglas James; Caporuscio, Florie Andre; Otto, Shawn; Boukhalfa, Hakim; Jordan, Amy B.; Chu, Shaoping; Zyvoloski, George Anthony; Johnson, Peter Jacob

2017-01-01

Salt is an attractive material for the disposition of heat generating nuclear waste (HGNW) because of its self-sealing, viscoplastic, and reconsolidation properties (Hansen and Leigh, 2012). The rate at which salt consolidates and the properties of the consolidated salt depend on the composition of the salt, including its content in accessory minerals and moisture, and the temperature under which consolidation occurs. Physicochemical processes, such as mineral hydration/dehydration salt dissolution and precipitation play a significant role in defining the rate of salt structure changes. Understanding the behavior of these complex processes is paramount when considering safe design for disposal of heat-generating nuclear waste (HGNW) in salt formations, so experimentation and modeling is underway to characterize these processes. This report presents experiments and simulations in support of the DOE-NE Used Fuel Disposition Campaign (UFDC) for development of drift-scale, in-situ field testing of HGNW in salt formations.

Experiments and Modeling in Support of Generic Salt Repository Science

Energy Technology Data Exchange (ETDEWEB)

Bourret, Suzanne Michelle [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stauffer, Philip H. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Weaver, Douglas James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Caporuscio, Florie Andre [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Otto, Shawn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boukhalfa, Hakim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Jordan, Amy B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chu, Shaoping [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Zyvoloski, George Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Johnson, Peter Jacob [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-01-19

Salt is an attractive material for the disposition of heat generating nuclear waste (HGNW) because of its self-sealing, viscoplastic, and reconsolidation properties (Hansen and Leigh, 2012). The rate at which salt consolidates and the properties of the consolidated salt depend on the composition of the salt, including its content in accessory minerals and moisture, and the temperature under which consolidation occurs. Physicochemical processes, such as mineral hydration/dehydration salt dissolution and precipitation play a significant role in defining the rate of salt structure changes. Understanding the behavior of these complex processes is paramount when considering safe design for disposal of heat-generating nuclear waste (HGNW) in salt formations, so experimentation and modeling is underway to characterize these processes. This report presents experiments and simulations in support of the DOE-NE Used Fuel Disposition Campaign (UFDC) for development of drift-scale, in-situ field testing of HGNW in salt formations.

Salton Sea Geothermal Field, California, as a near-field natural analog of a radioactive waste repository in salt

Science.gov (United States)

Elders, W. A.; Cohen, L. H.

1983-11-01

Since high concentrations of radionuclides and high temperatures are not normally encountered in salt domes or beds, finding an exact geologic analog of expected near-field conditions in a mined nuclear waste repository in salt will be difficult. The Salton Sea Geothermal Field, however, provides an opportunity to investigate the migration and retardation of naturally occurring U, Th, Ra, Cs, Sr and other elements in hot brines which have been moving through clay-rich sedimentary rocks for up to 100,000 years. The more than thirty deep wells drilled in this field to produce steam for electrical generation penetrate sedimentary rocks containing concentrated brines where temperatures reach 3650C at only 2 km depth. The brines are primarily Na, K, Ca chlorides with up to 25% of total dissolved solids; they also contain high conentrations of metals such as Fe, Mn, Li, Zn, and Pb. This report describes the geology, geophysics and geochemistry of this system as a prelude to a study of the mobility of naturally occurring radionuclides and radionuclide analogs within it.

Repositories; Repositorios

Energy Technology Data Exchange (ETDEWEB)

Freire, Carolina Braccini; Tello, Cledola Cassia Oliveira de [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mails: cbf@cdtn.br; tellocc@cdtn.br

2007-11-15

The use of the nuclear energy is increasing in all areas. Then the radioactive waste management is in continuous development to comply the national and international established requirements. The final objective is to assure that it will not have any contamination of the public or the environmental, and that the exposition doses will be lower than the radiological protection limits. The multi barrier concept for the repository is internationally recognized. Among the repository types, the most used are: near surface, geological formations and of deposition in rock cavities. This article explains the concept and the types of repository and gives some examples of them. (author)

New developments in measurements technology relevant to the studies of deep geological repositories in bedded salt

International Nuclear Information System (INIS)

Mao, N.; Ramirez, A.L.

1980-01-01

This report presents new developments in measurement technology relevant to the studies of deep geological repositories for nuclear waste disposal during all phases of development, i.e., site selection, site characterization, construction, operation, and decommission. Emphasis has been placed on geophysics and geotechnics with special attention to those techniques applicable to bedded salt. The techniques are grouped into sections as follows: tectonic environment, state of stress, subsurface structures, fractures, stress changes, deformation, thermal properties, fluid transport properties, and other approaches. Several areas that merit further research and developments are identified. These areas are: in situ thermal measurement techniques, fracture detection and characterization, in situ stress measurements, and creep behavior. The available instrumentations should generally be improved to have better resolution and accuracy, enhanced instrument survivability, and reliability for extended time periods in a hostile environment

New developments in measurements technology relevant to the studies of deep geological repositories in bedded salt

Science.gov (United States)

Mao, N. H.; Ramirez, A. L.

1980-10-01

Developments in measurement technology are presented which are relevant to the studies of deep geological repositories for nuclear waste disposal during all phases of development, i.e., site selection, site characterization, construction, operation, and decommission. Emphasis was placed on geophysics and geotechnics with special attention to those techniques applicable to bedded salt. The techniques are grouped into sections as follows: tectonic environment, state of stress, subsurface structures, fractures, stress changes, deformation, thermal properties, fluid transport properties, and other approaches. Several areas that merit further research and developments are identified. These areas are: in situ thermal measurement techniques, fracture detection and characterization, in situ stress measurements, and creep behavior. The available instrumentations should generally be improved to have better resolution and accuracy, enhanced instrument survivability, and reliability for extended time periods in a hostile environment.

Calculations on the development in space and time of the temperature field around a repository of medium and high active wastes in a salt formation

International Nuclear Information System (INIS)

Delisle, G.

1980-01-01

The concept of nuclear waste disposal of th of the Federal Republic of Germany calls for the burial of the wastes within a salt formation. A small portion of the wastes will generate heat after the disposal procedure. A temperature rise within the salt formation, in space and time limited, will be the consequence. The temperature change at any point in the near or far field of the disporal area can be calculated with the aid of numerical models. The thermal parameters representative for the bulk material of the Zechstein formation in NW-Germany, on which the calculations are based, will be discussed in detail. The interrelation between the concentration of heat producing wastes in the disposal field and the maximum average temperature in the salt formation will be treated. By defining numerical models, which are based on assumed shapes of a salt dome and a disposal area, the temperature development in the near and far field of a nuclear repository are shown. (orig.) [de

Summary of repository siting models. Final report

International Nuclear Information System (INIS)

Thomas, S.D.; Ross, B.; Mercer, J.W.

1982-07-01

This report is the first in a series of reports that will provide critical reviews and summaries of computer programs that can be used to analyze the potential performance of a high-level radioactive waste repository. The computer programs identified address the following phenomena: saturated and unsaturated subsurface flow, heat transport, solute transport, surface water runoff, geomechanical interactions, and geochemical interactions. The report identifies 183 computer programs that can be used to analyze a repository site and provides a summary description of 31 computer programs. The summary descriptions can be used: to assist in code evaluation, to facilitate code comparison, to determine applicability of codes to specific problems, to identify code deficiencies, and to provide a screening mechanism for code selection

Probabilistic methods as a tool aiding dimensioning drift and shaft seals for a repository in rock salt

Energy Technology Data Exchange (ETDEWEB)

Roehlig, Klaus-Juergen; Plischke, Elmar; Li, Xiaoshuo [TU Clausthal, Clausthal-Zellerfeld (Germany). Inst. of Disposal Research (IELF)

2015-07-01

For repositories in rock salt, demonstrating the integrity of drift and shaft seals is an indispensable part of the long-term safety case. In this study, probabilistic methods are applied to assess the fictitious abutment length for a shaft seal and the effective permeability of a drift seal (dam), i.e. the integral entity for the whole structure including contact zone and damaged salt zone. For the seal permeability, the question arises how to derive it based on permeability measurements with a limited number of samples due to cost restrictions. Furthermore, it is of interest which conclusions can be derived regarding the minimum length of drift seals if the failure probability should be smaller than e.g. 10{sup -4}. Based on numerical experiments it was demonstrated that small-scale measurements can be upscale using known averaging methods. This suggests that dimensioning can be carried out based on cautions average estimates and the required reliability statement (e.g. about a failure probability smaller than e.g. 10{sup -4}) can be derived for realistic dam lengths. However, due to the limited amount of data available there are remaining uncertainties concerning the underlying model assumptions.

Probabilistic methods as a tool aiding dimensioning drift and shaft seals for a repository in rock salt

International Nuclear Information System (INIS)

Roehlig, Klaus-Juergen; Plischke, Elmar; Li, Xiaoshuo

2015-01-01

For repositories in rock salt, demonstrating the integrity of drift and shaft seals is an indispensable part of the long-term safety case. In this study, probabilistic methods are applied to assess the fictitious abutment length for a shaft seal and the effective permeability of a drift seal (dam), i.e. the integral entity for the whole structure including contact zone and damaged salt zone. For the seal permeability, the question arises how to derive it based on permeability measurements with a limited number of samples due to cost restrictions. Furthermore, it is of interest which conclusions can be derived regarding the minimum length of drift seals if the failure probability should be smaller than e.g. 10 -4 . Based on numerical experiments it was demonstrated that small-scale measurements can be upscale using known averaging methods. This suggests that dimensioning can be carried out based on cautions average estimates and the required reliability statement (e.g. about a failure probability smaller than e.g. 10 -4 ) can be derived for realistic dam lengths. However, due to the limited amount of data available there are remaining uncertainties concerning the underlying model assumptions.

Science is the first step to siting nuclear waste repositories

Science.gov (United States)

Neuzil, Christopher E.

2014-01-01

As Shaw [2014] notes, U.S. research on shale as a repository host was halted before expending anything close to the effort devoted to studying crystalline rock, salt, and - most notably - tuff at Yucca Mountain. The new political reality regarding Yucca Mountain may allow reconsideration of the decision to abandon research on shale as a repository host.

Test procedures for salt rock

International Nuclear Information System (INIS)

Dusseault, M.B.

1985-01-01

Potash mining, salt mining, design of solution caverns in salt rocks, disposal of waste in salt repositories, and the use of granular halite backfill in underground salt rock mines are all mining activities which are practised or contemplated for the near future. Whatever the purpose, the need for high quality design parameters is evident. The authors have been testing salt rocks in the laboratory in a number of configurations for some time. Great care has been given to the quality of sample preparation and test methodology. This paper describes the methods, presents the elements of equipment design, and shows some typical results

Problem trap final repository. Social challenges concerning nuclear waste

International Nuclear Information System (INIS)

Brunnengraeber, Achim

2016-01-01

How is it possible that there is still no final storage facility in the entire world for highly radioactive waste from nuclear power stations? How is it possible that electricity has been generated by industrial-scale nuclear installations for decades without the issue of the disposal of nuclear waste having been resolved? The events in Chernobyl in 1986 and Fukushima in 2011 have made it blatantly obvious how risky this technology is and how important it is to keep humans and the environment at a safe distance from radioactivity. This anthology examines the technological, political, social and economic dimensions of the permanent disposal of nuclear waste. It provides an insight into the emergence of the problem and the people involved and their interests. It describes and analyses the changes that are taking place in Germany (for instance, in relation to the government's commission on nuclear repositories) and other countries with regard to how they handle nuclear waste. The book deals with both questions related to socio-technical aspects of the permanent disposal of nuclear waste and calls for the democratic need for participation and new ways of doing so, without which the search for a permanent disposal site will not bear fruit. This anthology presents a comprehensive discussion of the disposal of nuclear waste and the search for a permanent repository for it. Not only will students and teachers find it extremely useful, but so will any readers who are interested in its subject matter and wish to gain a more in-depth insight into it.

ERG review of salt constitutive law, salt stress determinations, and salt corrosion and modeling studies

International Nuclear Information System (INIS)

Balon, J.E.

1986-03-01

The Engineering Review Group (ERG) was established by the Office of Nuclear Waste Isolation (ONWI) to help evaluate engineering-related issues in the US Department of Energy's nuclear waste repository program. The August 1983 meeting of the ERG reviewed a RE/SPEC technical report containing a review of eight constitutive laws that have been proposed to model the creep of salt over the ranges of stress and temperature anticipated in a nuclear repository. This report documents the ERG's comments and recommendations on this subject and the ONWI responses to the specific points raised by the ERG

Project Guarantee 1985. Final repository for low- and intermediate level radioactive wastes: Safety report

International Nuclear Information System (INIS)

Anon.

1985-01-01

Storage of radioactive waste must delay the return of radionuclides to the biosphere for a long period of time and must maintain the release rates at a sufficiently low level for all time. This is achieved with the aid of a series of safety barriers which consist, on the one hand, of technical barriers in the repository and, on the other hand , of natural geological barriers as they occur at the repository location. In order to assess the efficiency of the barriers, the working methods of the technical barriers and the host rock must be understood. This understanding is transferred into quantitative models in order to calculate the safety of the repository. The individual barriers and the methods used to modelling their functions were described in volume NGB 85-07 of the Project Guarantee 1985 report series and the data necessary for modelling were given. The models and data are used in the safety analysis, the results of which are contained in the present report. Safety considerations show that models are available in Switzerland which allow, in principle, an assessment of the long-term behaviour of a repository for low- and intermediate-level waste. The evaluation of earlier studies and experimental work, suitable laboratory measurements and results from field research enable compilation of a representative data-set so that the requirements for quantitative statements on safety of final disposal are met from this side also. The safety calculations show that the radiation doses calculated for a base case scenario with realistic/conservative parameter values are negligibly low. Also, radiation doses which are clearly under the protection standard of 10 mrem per year result for conservative values and the cumulation of several conservative assumptions. Even assuming exposure of the repository by erosion, a radiotoxicity of the soil formed results which is under natural values

Learning from nuclear waste repository design: the ground-control plan

International Nuclear Information System (INIS)

Schmidt, B.

1988-01-01

At present, under a U.S. Department of Energy program, three repositories for commercial spent fuel-in salt, tuff and basalt-are in the phase of site characterization and conceptual design, and one pilot project for defense waste in salt is under development. Because of strict quality assurance requirements throughout design and construction, and the need to predict and ascertain in advance the satisfactory performance of the underground openings, underground openings in the unusual circumstances of the repository environment have been analysed. This will lead to an improved understanding of rock behavior and improved methods of underground analysis and design. A formalized ground control plan was developed, the principles of which may be applied to other types of projects. This paper summarizes the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements. (author)

Mechanical and hydraulic behaviour of compacting crushed salt backfill at low porosities. Project REPOPERM. Phase 2

Energy Technology Data Exchange (ETDEWEB)

Kroehn, Klaus-Peter; Czaikowski, Oliver; Wieczorek, Klaus; Zhang, Chun-Liang; Moog, Helge; Friedenberg, Larissa [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Koeln (Germany); Stuehrenberg, Dieter; Heemann, Ulrich [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany); Jobmann, Michael; Mueller, Christian; Schirmer, Sonja [DBE Technology GmbH (DBE TEC), Peine (Germany)

2017-02-15

The compaction behavior of crushed salt has been extensively investigated by means of experimental as well as theoretical work. The readiness of numerical tools for the application to modeling the complex coupled thermo-hydro-mechanical processes in the crushed salt backfilled in a repository in salt rock has also been demonstrated. Compaction tests were performed under repository-relevant conditions. These tests were supplemented by laboratory work aiming at specific aspects of compaction. The following list covers the topics of these investigations as well as the main results. - Revisiting the determination of the porosity in relevant, past experiments (BGR). - Influence of the grain size distribution on compaction (BGR). - Triaxial compaction test with dry material at low porosities (BGR). - Investigation of the influence of humidity on compaction covers several subtopics. - Permeability associated with low porosity includes two subtopics. - Constitutive equations for two -phase flow (GRS). - Microstructural Investigations (DBE TEC). Parallel to the experimental work attention focussed on several aspects of the basics for modelling the compaction of crushed salt. This work covers checking the validity of the established numerical tools as well as exploring new methods. Topics and main results are listed here: - Development/definition and comparison of constitutive models (BGR). - Benchmark calculations (BGR and GRS). - Capability of scaling-rules for capillary pressure from the oil industry (GRS). - Application of discrete element codes to compacting crushed salt (DBE TEC). Finally, repository-relevant scenarios are discussed as a basis for a realistic but generic numerical model of brine inflow in to a converging back filled drift under a thermal gradient (GRS). This exercise demonstrates the feasibility of modelling crushed salt compaction as a fully coupled thermohydraulic-mechanical process including two-phase flow effects.

Mechanical and hydraulic behaviour of compacting crushed salt backfill at low porosities. Project REPOPERM. Phase 2

International Nuclear Information System (INIS)

Kroehn, Klaus-Peter; Czaikowski, Oliver; Wieczorek, Klaus; Zhang, Chun-Liang; Moog, Helge; Friedenberg, Larissa; Stuehrenberg, Dieter; Heemann, Ulrich; Jobmann, Michael; Mueller, Christian; Schirmer, Sonja

2017-02-01

The compaction behavior of crushed salt has been extensively investigated by means of experimental as well as theoretical work. The readiness of numerical tools for the application to modeling the complex coupled thermo-hydro-mechanical processes in the crushed salt backfilled in a repository in salt rock has also been demonstrated. Compaction tests were performed under repository-relevant conditions. These tests were supplemented by laboratory work aiming at specific aspects of compaction. The following list covers the topics of these investigations as well as the main results. - Revisiting the determination of the porosity in relevant, past experiments (BGR). - Influence of the grain size distribution on compaction (BGR). - Triaxial compaction test with dry material at low porosities (BGR). - Investigation of the influence of humidity on compaction covers several subtopics. - Permeability associated with low porosity includes two subtopics. - Constitutive equations for two -phase flow (GRS). - Microstructural Investigations (DBE TEC). Parallel to the experimental work attention focussed on several aspects of the basics for modelling the compaction of crushed salt. This work covers checking the validity of the established numerical tools as well as exploring new methods. Topics and main results are listed here: - Development/definition and comparison of constitutive models (BGR). - Benchmark calculations (BGR and GRS). - Capability of scaling-rules for capillary pressure from the oil industry (GRS). - Application of discrete element codes to compacting crushed salt (DBE TEC). Finally, repository-relevant scenarios are discussed as a basis for a realistic but generic numerical model of brine inflow in to a converging back filled drift under a thermal gradient (GRS). This exercise demonstrates the feasibility of modelling crushed salt compaction as a fully coupled thermohydraulic-mechanical process including two-phase flow effects.

Reactive transport predictions for an Olkiluoto. Final repository tunnel unit

International Nuclear Information System (INIS)

Luukkonen, A.; Nordman, H.

2007-09-01

The presented hydrogeochemical reactive transport calculations concentrate to a defined unit piece (unit cell) of the planned Olkiluoto repository that is under design for spent nuclear fuel. The material properties assigned to the tunnel unit are based on literature as far as possible. Calculations make up geochemical future scenarios on the repository evolution. Most recent predictions on the potential future climate at Olkiluoto are utilised together with estimates how future hydraulic conditions affect the repository. Two climate scenarios are considered in detail. The Weichselian-R scenario is based on the repetition of the last glacial cycle, while the Emissions-M scenario attempts to predict the future groundwater conditions at Olkiluoto in the situation where the atmospheric greenhouse gasses delay the next glacial cycle at least for 100,000 years. The groundwater compositions, considered active at the repository depth in future, are judged in this study. Several geochemical processes are considered active at the repository depth. Calculations concentrate on the changes occurring with time within the tunnel unit. All simulations are done in geochemically reducing conditions. It turns out that sulphur cycling in these conditions is in central role considering the safety assessment studies of Olkiluoto repository. Furthermore, groundwater salinity and cation occupancy within the exchange sites of montmorillonite contributes to sealing properties of the engineered barrier system. Calculations attempt to estimate effects of possible future scenarios for the Olkiluoto repository. The results indicate that the buffer capacities assigned to the tunnel unit are large enough, at least to next 100,000 years, to maintain dissolved sulphide contents low in the groundwater infiltrating through the tunnel engineered barrier system. Geochemical reactions raise the bicarbonate levels within the groundwater. This is a useful buffer if low pH conditions emerge in the

Nuclear waste repository simulation experiments

International Nuclear Information System (INIS)

Rothfuchs, T.; Wieczorek, K.; Feddersen, H.K.; Staupendahl, G.; Coyle, A.J.; Kalia, H.; Eckert, J.

1986-12-01

This document is the third joint annual report on the Cooperative German-American 'Brine Migration Tests' that are in progress at the Asse salt mine in the Federal Republic of Germany (FRG). This Government supported mine serves as an underground test facility for research and development (R and D)-work in the field of nuclear waste repository research and simulation experiments. The tests are designed to simulate a nuclear waste repository to measure the effects of heat and gamma radiation on brine migration, salt decrepitation, disassociation of brine, and gases collected. The thermal mechanical behavior of salt, such as room closure, stresses and changes of the properties of salt are measured and compared with predicted behavior. This document covers the following sections: Issues and test objectives: This section presents issues that are investigated by the Brine Migration Test, and the test objectives derived from these issues; test site: This section describes the test site location and geology in the Asse mine; test description: A description of the test configuration, procedures, equipment, and instrumentation is given in this section; actual test chronology: The actual history of the test, in terms of the dates at which major activities occured, is presented in this section. Test results: This section presents the test results observed to data and the planned future work that is needed to complete the test; conclusions and recommendations: This section summarizes the conclusions derived to date regarding the Brine Migration Test. Additional work that would be useful to resolve the issues is discussed. (orig.)

Measurement and evaluation of the water and the salt solutions occurring in the exploitation of rock salt, potash or copper shale deposits in the Bernburg Hauptsattel or the Sangerhaeuser Revier in order to assess the long-term safety of repositories

International Nuclear Information System (INIS)

Schwandt, A.

1993-01-01

For a thorough assessment of conditions governing the occurrence of salt solutions or water in a repository in the Zechstein, i.e. in the salt formation and at its boundaries, data measured in other mines developed in this formation can yield valuable information. The studies reported were based on geological, hydrogeological, geochemical and geomechanical data collected for more than 50 inflow areas or salt solution bearing areas, covering approx. 15,000 chemical or physical analyses from which the data were derived describing the characteristics or development of inflow streams with time. In addition, the mapped inflow streams were evaluated with a view to the geological and hydrogeological and the geomechanical conditions of origin, as well as engineering impacts. (DG) [de

Final disposal of decommissioning wastes in the Federal Republic of Germany

Energy Technology Data Exchange (ETDEWEB)

Brewitz, W; Stippler, R

1981-01-01

The waste disposal concept of the Federal Republic of Germany for nuclear power plants provides for the final disposal of radioactive waste in deep geological formations and mines. The radiological safety of such a repository depends on a system of multiple barriers of which the geological barrier is the most important one. The isolation concept must guarantee the waste to decay below the limiting values of the German Radiation Protection Regulation within the repository. The expected total decommissioning waste masses from 12 nuclear power plants operating in the Federal Republic of Germany amounts to approxiametly 85000 Mg. For the final disposal of these wastes there are, under present aspects, two mines being considered as repositories. The pilot repository in the Asse II salt mine is in the state of licensing. The adandoned iron ore mine Konrad is being investigated for its feasibility and licensing will probably be initiated in 1982. Capacity and efficiency calculations have proved that both mines have got the technical requirements needed for the disposal of decommissioning and operating wastes from existent as well as from future built nuclear power plants.

Seismic monitoring of an Underground Repository in Salt - Results of the measurements at the Gorleben Exploratory mine

International Nuclear Information System (INIS)

Altmann, Jurgen

2013-01-01

We have measured seismic and acoustic signals from various mining activities in the Gorleben exploratory mine in Germany, underground at -840 m and at the surface, tasked by the German Support Programme to the IAEA, in order to provide basic knowledge on the detectability of undeclared activities. During 7 weeks total nearly all sources of sound and vibration available in the mine were covered, with sensors at several positions and sources at several sites, sometimes with background signals from on-going exploration elsewhere. The peak-to-peak values of vibration velocity, referred to 100 m distance, range from tenths of micro metres/second for a hand-held chain saw via few μm/s to tens of μm/s for other tools such as picking, for vehicles, drilling and sledge-hammer blows. A grader with compactor plates produces hundreds, and a blast shot around one hundred thousand μm/s. The last two sources could be detected at the surface, too, at about 1.1 km slant distance; blasts were even seen at 5-6 km distance. The signal strengths vary by a factor 2 to 5 for similar conditions. Fitted by a power law, the decrease with distance is with an exponent mostly between -2 and -1. Spectra of seismic signals from periodic sources (such as percussion drilling or vehicle engines) show harmonic series. Rock removal, e.g. by drilling, produces broad-band excitation up to several kilohertz. Acoustic-seismic coupling is relevant. Monitoring could be done with an underground geophone “fence” around the repository, e.g. 500 m from the salt-dome margin and possibly in the salt 1 km off the repository. With that excavation by drilling and blasting could be detected by a simple amplitude criterion. Under which conditions excavation by tunnel boring machine or road header machine and other weaker activities could be detected needs to be studied.

Conceptual design of retrieval systems for emplaced transuranic waste containers in a salt bed depository. Final report

International Nuclear Information System (INIS)

Fogleman, S.F.

1980-04-01

The US Department of Energy and the Nuclear Regulatory Commission have jurisdiction over the nuclear waste management program. Design studies were previously made of proposed repository site configurations for the receiving, processing, and storage of nuclear wastes. However, these studies did not provide operational designs that were suitable for highly reliable TRU retrieval in the deep geologic salt environment for the required 60-year period. The purpose of this report is to develop a conceptual design of a baseline retrieval system for emplaced transuranic waste containers in a salt bed depository. The conceptual design is to serve as a working model for the analysis of the performance available from the current state-of-the-art equipment and systems. Suggested regulations would be based upon the results of the performance analyses

Site Study Plan for salt, Deaf Smith County site, Texas: Environmental Field Program: Preliminary draft

International Nuclear Information System (INIS)

1987-06-01

The Salt Site Study Plan (SSP) describes a program for characterizing the existing salt environment in the site vicinity. A step-by-step approach is described which proceeds from published data and planned theoretical studies, to planned laboratory studies, and finally to planned field studies, to provide the necessary data to meet program requirements contained in the Salt Repository Project - Requirements Document (SRP-RD). The plan also draws on the results of other SSP's for certain data; for example, soil salinity data are to be provided under the Soils SSP. The salt studies consist of evaluation of control and mitigation measures, salt monitoring studies, emission factors development, air models development and validation, and risk assessment. For each study, its design and design rationale; analysis, management, and use of data; schedule of activities; organization of personnel and sample management; and quality assurance requirements are described. 90 refs., 9 figs., 7 tabs

Engineering solution for the backfilling and sealing of radioactive waste repositories

International Nuclear Information System (INIS)

Jorda, M.; Gouvenot, D.; Bonne, A.; Lees, T.P.; Schmidt, M.

1990-01-01

To ensure the safety of radioactive waste deep disposal, backfilling and sealing materials (engineered barriers) have to be used to fill residual voids. For granite medium, stress is put on emplacement techniques for cement- and clay-based materials, including in-situ validation. For clay medium, mined repository and deep boreholes drilled from the surface are considered. In the case of the first solution, the thermomechanical behaviour of a clay backfill is studied. In the same way, backfill made of excavated crushed salt is considered and thermomechanical properties evaluated by means of laboratory tests and in-situ experiments. Finally, basic works on quality assurance procedures and historic concretes behaviour are reported

Shaft sealing concepts for high-level radioactive waste repositories based on the host-rock options rock salt and clay stone; Schachtverschlusskonzepte fuer zukuenftige Endlager fuer hochradioaktive Abfaelle fuer die Wirtsgesteinsoptionen Steinsalz und Ton

Energy Technology Data Exchange (ETDEWEB)

Kudla, Wolfram; Gruner, Matthias [TU Bergakademie Freiberg (Germany). Inst. fuer Erdbau und Spezialtiefbau; Herold, Philipp; Jobmann, Michael [DBE Technology GmbH, Peine (Germany)

2015-07-01

Unlike the shaft barriers used for the dry preservation of former mine workings and underground storage sites, shaft seals designed for radioactive-waste repositories must also fulfil additional requirements associated with the design diversity of the sealing system. This diversity makes use of the simple redundancy principle in order to prevent the proliferation of defects. In practice this means combining several sealing elements made from different materials or from materials with different properties. The R and D project, Shaft sealing systems for final repositories for high-level radioactive waste (ELSA) - phase 2: concept design for shaft seals and testing of the functional elements of shaft seals', which was funded by the Federal Ministry for Economic Affairs and Energy (BMWi), set out to investigate potential sealing elements for the two host-rock options rock salt and mudstone. This paper combines the text that the authors presented at the First International Freiberg Shaft Colloquium held at the Freiberg University of Mining and Technology on 01.10.2014 with a presentation on the sealing elements that were investigated as part of the R and D project.

Analysis of the corrosion of carbon steels in simulated salt repository brines and acid chloride solutions at high temperatures

International Nuclear Information System (INIS)

Diercks, D.R.; Kassner, T.F.

1988-04-01

An analysis of literature data on the corrosion of carbon steels in anoxic brines and acid chloride solutions was performed, and the results were used to assess the expected life of high-level nuclear waste package containers in a salt repository environment. The corrosion rate of carbon steels in moderately acidic aqueous chloride environments obeys an Arrhenius dependence on temperature and a (pH 2 ) -1/2 dependence on hydrogen partial pressure. The cathodic reduction of water to produce hydrogen is the rate-controlling step in the corrosion process. An expression for the corrosion rate incorporating these two dependencies was used to estimate the corrosion life of several proposed waste package configurations. 42 refs., 11 figs., 2 tabs

Improvements of Spiers model for compaction creep of crushed rock salt

International Nuclear Information System (INIS)

Poley, A.D.

1996-10-01

This report describes a number of improvements to the existing model for the process of compaction creep of rock salt developed by Spiers and co-workers. The process of compaction creep determines the behaviour of the seals of crushed rock salt, the last engineered barriers of a repository in rock salt for (radioactive) wastes. In Chapter 2 the derivation of the original model of Spiers and co-workers is followed except for some simplifying approximations. A comparison of the model results is made with experimental data and a number of model adjustments are suggested. In Chapter 3 one of these suggested model adjustments is explored, and an alternative model is developed. The results obtained with this model compare favourably with the experimental data without the use of adjustable shape functions as for the original model. Preliminary investigations of the impact of the new model on estimated releases to the geosphere of radionuclides form a repository in rock salt revealed striking differences: with the new model the compaction of the rock salt seals was so rapid that no releases could occur. The striking differences between the results - in terms of releases form a rock salt repository to the geosphere after groundwater intrusion - obtained using the two models clearly indicate the need for further experimental research into the end-compaction behaviour of rock salt backfill. (orig.)

Radioactive waste isolation in salt: peer review of Westinghouse Electric Corporation's report on reference conceptual designs for a repository waste package

International Nuclear Information System (INIS)

Rote, D.M.; Hull, A.B.; Was, G.S.; Macdonald, D.D.; Wilde, B.E.; Russell, J.E.; Kruger, J.; Harrison, W.; Hambley, D.F.

1985-10-01

This report documents the findings of the peer panel constituted by Argonne National Laboratory to review Region A of Westinghouse Electric Corporation's report entitled Waste Package Reference Conceptual Designs for a Repository in Salt. The panel determined that the reviewed report does not provide reasonable assurance that US Nuclear Regulatory Commission (NRC) requirements for waste packages will be met by the proposed design. It also found that it is premature to call the design a ''reference design,'' or even a ''reference conceptual design.'' This review report provides guidance for the preparation of a more acceptable design document

NWTS conceptual reference repository description (CRRD). Volume 1. Summary

International Nuclear Information System (INIS)

1981-05-01

This report is a Conceptual Reference Repository Description (CRRD) for the terminal storage of spent, unreprocessed fuel assemblies and low-level transuranic waste. It is based on the following three previously prepared conceptual design reports: National Waste Terminal Storage in a Bedded Salt Formation for Spent Unreprocessed Fuel (NWTS-R2), prepared by Kaiser Engineers; National Waste Terminal Storage Repository Number 1 (NWTS-R1), prepared by Stearns-Roger; Spent Fuel Receiving and Packaging Facility Conceptual Design, prepared by Rockwell Hanford Operations and Kaiser Engineers. The CRRD is not itself a conceptual design report, but combines the key features of the above three reports into a description of a reference repository. This description is to be used as a basis for the preparation of a preliminary information report for the repositories. The CRRD discusses from a conceptual engineering standpoint the structures, systems, equipment, and operations necessary to (1) receive unreprocessed spent fuel assemblies via standard shipping casks, (2) offload these assemblies, (3) place the assemblies in canisters, (4) transport the canisters to underground storage locations in the salt dome, and (5) place these canisters in terminal storage. The CRRD also elaborates on the concepts for the retrieval and recovery of the spent fuel after burial; describes the development of the shafts and the underground areas,as well as the supporting operational utility and administrative features of the repository; and discusses the impacts on the reference repository of (1) changes in the waste package concept, (2) dry receiving and dry temporary storage of waste, (3) terminal storage of reprocessing waste, and (4) alternative underground development schemes

Modeling internal deformation of salt structures targeted for radioactive waste disposal

International Nuclear Information System (INIS)

Chemia, Zurab

2008-01-01

This thesis uses results of systematic numerical models to argue that externally inactive salt structures, which are potential targets for radioactive waste disposal, might be internally active due to the presence of dense layers or blocks within a salt layer. The three papers that support this thesis use the Gorleben salt diapir (NW Germany), which was targeted as a future final repository for high-grade radioactive waste, as a general guideline. The first two papers present systematic studies of the parameters that control the development of a salt diapir and how it entrains a dense anhydrite layer. Results from these numerical models show that the entrainment of a dense anhydrite layer within a salt diapir depends on four parameters: sedimentation rate, viscosity of salt, perturbation width and the stratigraphic location of the dense layer. The combined effect of these four parameters, which has a direct impact on the rate of salt supply (volume/area of the salt that is supplied to the diapir with time), shape a diapir and the mode of entrainment. Salt diapirs down-built with sedimentary units of high viscosity can potentially grow with an embedded anhydrite layer and deplete their source layer (salt supply ceases). However, when salt supply decreases dramatically or ceases entirely, the entrained anhydrite layer/segments start to sink within the diapir. In inactive diapirs, sinking of the entrained anhydrite layer is inevitable and strongly depends on the rheology of the salt, which is in direct contact with the anhydrite layer. During the post-depositional stage, if the effective viscosity of salt falls below the threshold value of around 10 18 -10 19 Pa s, the mobility of anhydrite blocks might influence any repository within the diapir. However, the internal deformation of the salt diapir by the descending blocks decreases with increase in effective viscosity of salt. The results presented in this thesis suggest that it is highly likely that salt structures

Release rates from waste packages in a salt repository

International Nuclear Information System (INIS)

Chambre, P.L.; Hwang, Y.; Lee, W.W.L.; Pigford, T.H.

1987-06-01

In this report we present estimates of radionuclide release rates from waste packages into salt. This conservative and bounding analysis shows that release rates from waste packages in salt are well below the US Nuclear Regulatory Commission's performance objectives for the engineered barrier system. 2 refs., 2 figs

Safety evaluation of geological disposal concepts for low and medium-level wastes in rock-salt (Pacoma project)

International Nuclear Information System (INIS)

Prij, J.; Van Dalen, A.; Roodbergen, H.A.; Slagter, W.; Van Weers, A.W.; Zanstra, D.A.; Glasbergen, P.; Koester, H.W.; Lembrechts, J.F.; Nijhof-Pan, I.; Slot, A.F.M.

1991-01-01

In the framework of the Performance Assessment of Confinements for MLW and Alpha Waste (PACOMA) the disposal options dealing with rock-salt are studied by GSF and ECN (with subcontract to RIVM). The overall objectives of these studies are to develop and demonstrate procedures for the radiological safety assessment of a deep repository in salt formations. An essential objective is to show how far appropriate choices of the repository design parameters can improve the performances of the whole system. The research covers two waste inventories (the Dutch OPLA and the PACOMA reference inventory), two disposal techniques (conventional and solution mining) and three types of formations (salt dome, pillow and bedded salt). An important part of the research has been carried out in the socalled VEOS project within the framework of the Dutch OPLA study. The methodology used in the consequence analysis is a deterministic one. The models and calculation tools used to perform the consequence analysis are the codes: EMOS, METROPOL and BIOS. The results are expressed in terms of dose rates and doses to individuals as well as to groups. Detailed information with respect to the input data and the results obtained with the three codes is given in three annexes to this final report

Final report on decommissioning of wells, boreholes, and tiltmeter sites, Gulf Coast Interior Salt Domes of Louisiana

Energy Technology Data Exchange (ETDEWEB)

1989-07-01

In the late 1970s, test holes were drilled in northern Louisiana in the vicinity of Vacherie and Rayburn`s Salt Domes as part of the Department of Energy`s (DOE) National Waste Terminal Storage (NWTS) (rename the Civilian Radioactive Waste Management (CRWM)) program. The purpose of the program was to evaluate the suitability of salt domes for long term storage or disposal of high-level nuclear waste. The Institute for Environmental Studies at Louisiana State University (IES/LSU) and Law Engineering Testing Company (LETCo) of Marietta, Georgia performed the initial field studies. In 1982, DOE awarded a contract to the Earth Technology Corporation (TETC) of Long Beach, California to continue the Gulf Coast Salt Dome studies. In 1986, DOE deferred salt domes from further consideration as repository sites. This report describes test well plugging and site abandonment activities performed by SWEC in accordance with Activity Plan (AP) 1--3, Well Plugging and Site Restoration of Work Sites in Louisiana. The objective of the work outlined in this AP was to return test sites to as near original condition as possible by plugging boreholes, removing equipment, regrading, and seeding. Appendices to this report contain forms required by State of Louisiana, used by SWEC to document decommissioning activities, and pertinent documentation related to lease/access agreements.

Final report on decommissioning of wells, boreholes, and tiltmeter sites, Gulf Coast Interior Salt Domes of Louisiana

International Nuclear Information System (INIS)

1989-07-01

In the late 1970s, test holes were drilled in northern Louisiana in the vicinity of Vacherie and Rayburn's Salt Domes as part of the Department of Energy's (DOE) National Waste Terminal Storage (NWTS) (rename the Civilian Radioactive Waste Management (CRWM)) program. The purpose of the program was to evaluate the suitability of salt domes for long term storage or disposal of high-level nuclear waste. The Institute for Environmental Studies at Louisiana State University (IES/LSU) and Law Engineering Testing Company (LETCo) of Marietta, Georgia performed the initial field studies. In 1982, DOE awarded a contract to the Earth Technology Corporation (TETC) of Long Beach, California to continue the Gulf Coast Salt Dome studies. In 1986, DOE deferred salt domes from further consideration as repository sites. This report describes test well plugging and site abandonment activities performed by SWEC in accordance with Activity Plan (AP) 1--3, Well Plugging and Site Restoration of Work Sites in Louisiana. The objective of the work outlined in this AP was to return test sites to as near original condition as possible by plugging boreholes, removing equipment, regrading, and seeding. Appendices to this report contain forms required by State of Louisiana, used by SWEC to document decommissioning activities, and pertinent documentation related to lease/access agreements

International perspective on repositories for low level waste

International Nuclear Information System (INIS)

Bergstroem, Ulla; Pers, Karin; Almen, Ylva

2011-12-01

Nuclear energy production gives rise to different types of radioactive waste. The use of nuclear isotopes within the research, industry and medical sectors also generates radioactive waste. To protect man and the environment from radiation the waste is isolated and contained by deposition in repositories. These repositories may have various designs regarding location, barriers etc depending on the potential danger of the waste. In Sweden, low- and intermediate level waste (LILW) is disposed of in the SFR repository in Forsmark. The repository is located 60 metres down into the bedrock under the bottom of the sea and covered by 6 metres of water. It is planned to extend SFR to accommodate decommissioning waste from the dismantling of the Swedish nuclear power facilities and also for the additional operation waste caused by the planned prolonged operation time. When planning the extension consultations will be carried out with the host municipality, authorities, organisations and general public. In planning the extension, SKB has performed a worldwide compilation of how other countries have, or plan to, handle the final disposal of similar wastes. The aim of this report is to give a brief description of LILW repositories worldwide; including general brief descriptions of many facilities, descriptions of the waste and the barriers as well as safety assessments for a few chosen repositories which represent different designs. The latter is performed, where possible, to compare certain features against the Swedish SFR. To provide a background and context to this study, international organisations and conventions are also presented along with internationally accepted principles regarding the management of radioactive waste. Similar to SFR, suitable locations for the repositories have, in many countries, been found at sites that already have, or used to have nuclear activities, such as reactor sites. Abandoned and disused mines, such as the salt mines in Germany, also

International perspective on repositories for low level waste

Energy Technology Data Exchange (ETDEWEB)

Bergstroem, Ulla; Pers, Karin; Almen, Ylva (SKB International AB (Sweden))

2011-12-15

Nuclear energy production gives rise to different types of radioactive waste. The use of nuclear isotopes within the research, industry and medical sectors also generates radioactive waste. To protect man and the environment from radiation the waste is isolated and contained by deposition in repositories. These repositories may have various designs regarding location, barriers etc depending on the potential danger of the waste. In Sweden, low- and intermediate level waste (LILW) is disposed of in the SFR repository in Forsmark. The repository is located 60 metres down into the bedrock under the bottom of the sea and covered by 6 metres of water. It is planned to extend SFR to accommodate decommissioning waste from the dismantling of the Swedish nuclear power facilities and also for the additional operation waste caused by the planned prolonged operation time. When planning the extension consultations will be carried out with the host municipality, authorities, organisations and general public. In planning the extension, SKB has performed a worldwide compilation of how other countries have, or plan to, handle the final disposal of similar wastes. The aim of this report is to give a brief description of LILW repositories worldwide; including general brief descriptions of many facilities, descriptions of the waste and the barriers as well as safety assessments for a few chosen repositories which represent different designs. The latter is performed, where possible, to compare certain features against the Swedish SFR. To provide a background and context to this study, international organisations and conventions are also presented along with internationally accepted principles regarding the management of radioactive waste. Similar to SFR, suitable locations for the repositories have, in many countries, been found at sites that already have, or used to have nuclear activities, such as reactor sites. Abandoned and disused mines, such as the salt mines in Germany, also

Methods of calculating the post-closure performance of high-level waste repositories

Energy Technology Data Exchange (ETDEWEB)

Ross, B. (ed.)

1989-02-01

This report is intended as an overview of post-closure performance assessment methods for high-level radioactive waste repositories and is designed to give the reader a broad sense of the state of the art of this technology. As described here, ''the state of the art'' includes only what has been reported in report, journal, and conference proceedings literature through August 1987. There is a very large literature on the performance of high-level waste repositories. In order to make a review of this breadth manageable, its scope must be carefully defined. The essential principle followed is that only methods of calculating the long-term performance of waste repositories are described. The report is organized to reflect, in a generalized way, the logical order to steps that would be taken in a typical performance assessment. Chapter 2 describes ways of identifying scenarios and estimating their probabilities. Chapter 3 presents models used to determine the physical and chemical environment of a repository, including models of heat transfer, radiation, geochemistry, rock mechanics, brine migration, radiation effects on chemistry, and coupled processes. The next two chapters address the performance of specific barriers to release of radioactivity. Chapter 4 treats engineered barriers, including containers, waste forms, backfills around waste packages, shaft and borehole seals, and repository design features. Chapter 5 discusses natural barriers, including ground water systems and stability of salt formations. The final chapters address optics of general applicability to performance assessment models. Methods of sensitivity and uncertainty analysis are described in Chapter 6, and natural analogues of repositories are treated in Chapter 7. 473 refs., 19 figs., 2 tabs.

Methods of calculating the post-closure performance of high-level waste repositories

International Nuclear Information System (INIS)

Ross, B.

1989-02-01

This report is intended as an overview of post-closure performance assessment methods for high-level radioactive waste repositories and is designed to give the reader a broad sense of the state of the art of this technology. As described here, ''the state of the art'' includes only what has been reported in report, journal, and conference proceedings literature through August 1987. There is a very large literature on the performance of high-level waste repositories. In order to make a review of this breadth manageable, its scope must be carefully defined. The essential principle followed is that only methods of calculating the long-term performance of waste repositories are described. The report is organized to reflect, in a generalized way, the logical order to steps that would be taken in a typical performance assessment. Chapter 2 describes ways of identifying scenarios and estimating their probabilities. Chapter 3 presents models used to determine the physical and chemical environment of a repository, including models of heat transfer, radiation, geochemistry, rock mechanics, brine migration, radiation effects on chemistry, and coupled processes. The next two chapters address the performance of specific barriers to release of radioactivity. Chapter 4 treats engineered barriers, including containers, waste forms, backfills around waste packages, shaft and borehole seals, and repository design features. Chapter 5 discusses natural barriers, including ground water systems and stability of salt formations. The final chapters address optics of general applicability to performance assessment models. Methods of sensitivity and uncertainty analysis are described in Chapter 6, and natural analogues of repositories are treated in Chapter 7. 473 refs., 19 figs., 2 tabs

Thermal-gradient migration of brine inclusions in salt

International Nuclear Information System (INIS)

Yagnik, S.K.

1982-02-01

It has been proposed that the high level nuclear waste be buried deep underground in a suitable geologic formation. Natural salt deposits have been under active consideration as one of the geologic formations where a nuclear waste repository may be built in future. The salt deposits, however, are known to contain a small amount (about 0.5 vol.%) of water in the form of brine inclusions which are dispersed throughout the medium. The temperature gradients imposed by the heat generating nuclear waste will mobilize these brine inclusions. It is important to know the rate and the amount of brine accumulating at the waste packages to properly evaluate the performance of a nuclear waste repository. An extensive experimental investigation of the migration velocities of brine inclusions in synthetic single crystals of NaCl and in polycrystalline natural salt crystals has been conducted. The results show that in a salt repository the brine inclusions within a grain would move with the diffusion controlled velocities. The brine reaching a grain boundary may be swept across, if the thermal gradient is high enough. Grain boundaries in polycrystalline rock salt are apparently quite weak and open up due to drilling the hole for a waste canister and to the thermal stresses which accompany the thermal gradient produced by the heat generating waste. The enhanced porosity allows the water reaching the grain boundary to escape by a vapor transport process

Development and validation of a predictive technology for creep closure of underground rooms in salt

International Nuclear Information System (INIS)

Munson, D.E.; DeVries, K.L.

1991-07-01

Because of the concern for public health and safety, when compared to normal engineering practice, radioactive waste repositories have quite unusual requirements governing performance assessment. In part, performance assessment requires prediction of time-dependent or creep response of the repository hundreds to thousands of years into the future. In salt, one specific need is to predict, with confidence, the time at which the repository rooms creep closed sufficiently to encapsulate the waste and seal the repository. Thus, a major task of the Waste Isolation Pilot Plant (WIPP) Program is to develop and validate this predictive technology to calculate creep of repository rooms in the bedded salt deposits of Southeastern New Mexico. 19 refs., 15 figs., 2 tabs

Final repository searching in Germany - what are the next steps?; Endlagerstandortsuche in Deutschland. Wie geht's weiter?

Energy Technology Data Exchange (ETDEWEB)

Neles, Julia Mareike [Oeko-Institut e.V., Darmstadt (Germany). Bereich Nukleartechnik und Anlagensicherheit

2016-07-01

Up to now (2016) the question of final disposal of high-level radioactive wastes is still open in Germany. The Commission of radioactive waste disposal has finalized its report including recommendations for the further process. The next step will be the site selection procedure based on a ''white map''. The protest of several Federal states and communities against repository sites in their region is already developing.

Geoelectric monitoring of bentonite barrier resaturation in the Aespoeprototype repository. Final report

Energy Technology Data Exchange (ETDEWEB)

Wieczorek, Klaus; Komischke, Michael; Miehe, Ruediger; Moog, Helge

2014-10-15

In 1994, SKB started constructing the ''Prototype Repository'', a full-scale replica of a part of a future KBS-3 repository in crystalline rock, at the AespoeHard Rock Laboratory. Six emplacement boreholes were planned and constructed in two tunnel sections until end of 1999. The international EC co-funded Prototype Repository project was started in 2000 (contract FIKW-CT-2000-00055). The project partners were SKB (Sweden), POSIVA (Finland), ENRESA (Spain), GRS (Germany), BGR (Germany), UWC (UK), and JNC (Japan). Between 2000 and 2003 the complete Prototype Repository was equipped and instrumented, and monitoring was started. In February 2004 the EC funding expired. The Prototype Repository project was continued with national funding of the project partners. In 2011, dismantling of Section II was started in a three-year project. Backfill, buffer and canisters as well as part of the instrumentation were retrieved, and numerous laboratory investigations on buffer and backfill samples were performed. GRS' part in the Prototype Repository was the monitoring of backfill and buffer resaturation using geoelectric tomography. The measurements were completed in 2013.

Formulation and evaluation of gas release scenarios for the silo in Swedish Final Repository for Radioactive Waste (SFR)

International Nuclear Information System (INIS)

Carlsson, J.; Moreno, L.

1992-01-01

The Swedish Final Repository for Radioactive Waste (SFR) has been in operation since 1988 and is located in the crystalline rock, 60 m below the Baltic Sea. In the licensing procedure for the SFR the safety assessment has been complemented with a detailed scenario analysis of the performance of the repository. The scenarios include the influence on radionuclide release by gas formation and gas transport processes in the silo. The overall conclusion is that the release of most radionuclides from the silo is only marginally affected by the formation and release of gas, even for scenarios considering unexpected events. The largest effects were found for short-lived radionuclides and radionuclides that have no or low sorption ability. Except for very extreme scenarios for the silo the overall impact from repository on the environment is by far dominated by the release of radionuclides from the rock vaults. 10 refs., 6 figs

Limits on the thermal energy release from radioactive wastes in a mined geologic repository

International Nuclear Information System (INIS)

Scott, J.A.

1983-03-01

The theraml energy release of nuclear wastes is a major factor in the design of geologic repositories. Thermal limits need to be placed on various aspets of the geologic waste disposal system to avoid or retard the degradation of repository performance because of increased temperatures. The thermal limits in current use today are summarized in this report. These limits are placed in a hierarchial structure of thermal criteria consistent with the failure mechanism they are trying to prevent. The thermal criteria hierarchy is used to evaluate the thermal performance of a sample repository design. The design consists of disassembled BWR spent fuel, aged 10 years, close packed in a carbon steel canister with 15 cm of crushed salt backfill. The medium is bedded salt. The most-restrictive temperature for this design is the spent-fuel centerline temperature limit of 300 0 C. A sensitivity study on the effects of additional cooling prior to disposal on repository thermal limits and design is performed

National radioactive wasterRepository Mochovce

International Nuclear Information System (INIS)

2000-01-01

In this leaflet the scheme of the Mochovce National radioactive waste repository for the Slovak Republic is presented. The National radioactive waste repository in Mochovce is a surface type storage facility. It is intended for final disposal of solid and solidified low and intermediate radioactive waste produced during the operation of nuclear power plants and institutions located within the territory of the Slovak Republic. The Repository site is situated about 2 km northwest to the Mochovce NPP

Exploratory shaft conceptual design report: Gulf Interior Region salt domes

International Nuclear Information System (INIS)

1983-07-01

This conceptual design report summarizes the conceptualized design for an exploratory shaft facility at a representative site in the Gulf Interior Region of the United States (Louisiana and Mississippi). Conceptualized designs for other possible locations (Paradox Basin in Utah and Permian Basin in Texas) are summarized in separate reports. The purpose of the exploratory shaft facility is to provide access to the reference repository horizon to permit in-situ testing of the salt. The in-situ testing is necessary to verify repository salt design parameters, evaluate isotropy and homoqeneity of the salt, and provide a demonstration of the constructability and confirmation of the design to gain access to the repository. The fundamental purpose of this conceptual design report is to assure the feasibility of the exploratory shaft project and to develop a reliable cost estimate and realistic schedule. Because a site has not been selected and site-specific subsurface data are not available, it has been necessary to make certain assumptions in order to develop a conceptural design for an exploratory shaft facility in salt. As more definitive information becomes available to support the design process, adjustments in the projected schedule and estimated costs will be required

Radiation induced F-center and colloid formation in synthetic NaCl and natural rock salt: applications to radioactive waste repositories

International Nuclear Information System (INIS)

Levy, P.W.; Loman, J.M.; Kierstead, J.A.

1983-01-01

Radiation damage, particularly Na metal colloid formation, has been studied in synthetic NaCl and natural rock salt using unique equipment for making optical absorption, luminescence and other measurements during irradiation with 1 to 3 MeV electrons. Previous studies have established the F-center and colloid growth phenomenology. At temperatures where colloids form most rapidly, 100 to 250 C, F-centers appear when the irradiation is initiated and increase at a decreasing rate to a plateau, reached at doses of 10 6 to 10 7 rad. Concomitant colloid growth is described by classical nucleation and growth curves with the transition to rapid growth occurring at 10 6 to 10 7 rad. The colloid growth rate is low at 100 C, increases markedly to a maximum at 150 to 175 C and decreases to a negligible rate at 225 C. At 1.2x10 8 rad/h the induction period is >10 4 sec at 100 C, 10 4 sec at 275 C. The colloid growth in salt from 14 localities is well described by C(dose)/sup n/ relations. Data on WIPP site salt (Los Medanos, NM, USA) has been used to estimate roughly the colloid expected in radioactive waste repositories. Doses of 1 to 2x10 10 rad, which will accumulate in salt adjacent to lightly shielded high level canisters in 200 to 500 years, will convert between 1 and 100% of the salt to Na colloids (and Cl) if back reactions or other limiting reactions do not occur. Each high level lightly shielded canister may ultimately be surrounded by 200 to 300 kg of colloid sodium. Low level or heavily shielded canisters may produce as little as 1 kg sodium

Some inspirations drawn from the SKB license-application report for the construction of the final repository for spent nuclear fuel in Sweden

International Nuclear Information System (INIS)

Xu Guoqing

2014-01-01

The following problems are described in this paper: the current state of nuclear energy and spent fuel in Sweden, the brief process of repository site selection and the concise geological settings of candidate site Forsmark, the option of repository design, the data presented in license-application report on repository, construction, the review work presented by OECD/NEA international peer review team (IRT) and some considerations noted by the author: 1) Why the design of underground engineering, also known as 5 shafts + l ramp, is adopted? 2) Why the timescale for the assessment is one million years? 3) Why the computer codes used in performance assessment at Forsmark candidate repository site are different from those used at Yucca Mountain candidate repository site? 4) How to carry out the public involvement, support from local government and volumtary siting in China? 5) What is the most important in the R and D program of HLW disposal? 6) What shall we do for the future license-application report for the construction of the final repository in China? (author)

IAEA safeguards for geological repositories

International Nuclear Information System (INIS)

Moran, B.W.

2005-01-01

In September. 1988, the IAEA held its first formal meeting on the safeguards requirements for the final disposal of spent fuel and nuclear material-bearing waste. The consensus recommendation of the 43 participants from 18 countries at this Advisory Group Meeting was that safeguards should not terminate of spent fuel even after emplacement in, and closure of, a geologic repository.' As a result of this recommendation, the IAEA initiated a series of consultants' meetings and the SAGOR Programme (Programme for the Development of Safeguards for the Final Disposal of Spent Fuel in Geologic Repositories) to develop an approach that would permit IAEA safeguards to verify the non-diversion of spent fuel from a geologic repository. At the end of this process, in December 1997, a second Advisory Group Meeting, endorsed the generic safeguards approach developed by the SAGOR Programme. Using the SAGOR Programme results and consultants' meeting recommendations, the IAEA Department of Safeguards issued a safeguards policy paper stating the requirements for IAEA safeguards at geologic repositories. Following approval of the safeguards policy and the generic safeguards approach, the Geologic Repository Safeguards Experts Group was established to make recommendations on implementing the safeguards approach. This experts' group is currently making recommendations to the IAEA regarding the safeguards activities to be conducted with respect to Finland's repository programme. (author)

Pressure-induced brine migration in consolidated salt in a repository

International Nuclear Information System (INIS)

Hwang, Y.; Chambre, P.L.; Lee, W.W.L.; Pigford, T.H.

1987-06-01

This report describes a mathematical model for brine migration through intact salt near a radioactive waste package emplaced in salt. Solutions indicate limited movement following ten years emplacement

National Geoscience Data Repository System: Phase 2 final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

The American Geological Institute (AGI) has completed Phase 2 of a project to establish a National Geoscience Data Repository System (NGDRS). The project`s primary objectives are to preserve geoscience data in jeopardy of being destroyed and to make that data available to those who have a need to use it in future investigations. These data are available for donation to the public as a result of the downsizing that has occurred in the major petroleum and mining companies in the US for the past decade. In recent years, these companies have consolidated domestic operations, sold many of their domestic properties and relinquished many of their leases. The scientific data associated with those properties are no longer considered to be useful assets and are consequently in danger of being lost forever. The national repository project will make many of these data available to the geoscience community for the first time. Phase 2 encompasses the establishment of standards for indexing and cataloging of geoscience data and determination of the costs of transferring data from the private sector to public-sector data repositories. Pilot projects evaluated the feasibility of the project for transfer of different data types and creation of a Web-based metadata supercatalog and browser. Also as part of the project, a national directory of geoscience data repositories was compiled to assess what data are currently available in existing facilities. The next step, Phase 3, will focus on the initiation of transfer of geoscience data from the private sector to the public domain and development of the web-based Geotrek metadata supercatalog.

Brine migration test for Asse Mine, Federal Republic of Germany: final test plan

International Nuclear Information System (INIS)

1983-07-01

The United States and the Federal Republic of Germany (FRG) will conduct a brine migration test in the Asse Salt Mine in the FRG as part of the US/FRG Cooperative Radioactive Waste Management Agreement. Two sets of two tests each will be conducted to study both liquid inclusion migration and vapor migration in the two salt types chosen for the experiments: (1) pure salt, for its characteristics similar to the salt that might occur in potential US repositories, and (2) transitional salt, for its similarity to the salt that might occur in potential repositories in Germany

Framework programme for detailed characterisation in connection with construction and operation of a final repository for spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

2010-10-15

This report presents a programme for the detailed investigations planned to be applied during construction and operation of the repository for spent nuclear fuel at Forsmark. The report is part of SKB's application according to the Nuclear Activities Act. The detailed investigations shall provide relevant data on and site-descriptive models for the bedrock, soil deposits and eco-system of the site in order to facilitate a step-wise design and construction of the final repository. This shall be implemented in a manner that all demands on long-term safety are fulfilled, including accurate documentation of the construction work, and so that assessments of the environmental impact of the repository can be made. For the operational phase, the detailed investigations should also provide support to the deposition process with related decisions, thereby enabling fulfilment of the design premises for the siting and construction of deposition tunnels and deposition holes, as well as for deposition of canisters, and for the subsequent backfilling and closure of the repository. The Observational Method will be applied during the construction of the repository. This method entails establishing in advance acceptable limits of behaviour regarding selected geoscientific parameters and preparing a plan with measures to keep the outcome within these limits. Predictions of expected rock properties are established for each tunnel section. The outcome after excavation is compared with the acceptable range of outcomes. Information from detailed characterization will be of essential importance for application of the Observational Method and for adapting the repository to the prevailing rock properties. SKB has for the past several decades developed methods for site characterisation, applying both above- and underground investigation techniques. Experiences from this work, put into practice during the site investigations, has resulted in a solid knowledge and understanding of the

Conference report: 2012 Repository Symposium. Final storage in Germany. New start - ways and consequences of the site selection procedure

International Nuclear Information System (INIS)

Kettler, John

2012-01-01

The Aachen Institute for Nuclear Training invited participants to the 3-day '2012 Repository Symposium - Final Storage in Germany' held in Bonn. The subtitle of the event, 'New Start - Ways and Consequences of the Site Selection Procedure,' expressed the organizers' summary that the Repository Finding Act currently under discussion did not give rise to any expectation of a repository for high-level radioactive waste before 2080. The symposium was attended by more than 120 persons from Germany and abroad. They discussed the basic elements of the site selection procedure and its consequences on the basis of the draft so far known to the public. While extensive public participation is envisaged for the stage of finding a repository, this does not apply to the draft legislation in the same way. The legal determinations are negotiated in a small circle by the political parties and the state governments. Michael Sailer (Oeko-Institut e.V.) holds that agreement on a repository finding act is urgent. Prof. Dr. Bruno Thomauske (RWTH Aachen) arrives at the conclusion mentioned above, that no repository for high-level radioactive waste can start operation before 2080 on the basis of the Repository Finding Act. Dr. Bettina Keienburg, attorney at law, in her paper drew attention to the points of dispute in the draft legislation with regard to changes in competency of public authorities. The draft law indicated a clear shift of competency for finding a repository from the Federal Office for Radiation Protection to a federal agency yet to be set up. Prof. Dr. Christoph Moench outlined the deficiencies of the draft legislation in matters of refinancing and the polluter-pays principle. Among the tentative solutions discussed it was above all the Swedish model which was acclaimed most widely. (orig.)

Disposal of high-level waste from nuclear power plants in Denmark. Salt dome investigations. v.2

International Nuclear Information System (INIS)

1981-01-01

The present report deals with the geological investigations performed for determing the feasibility of a repository for high-level waste in a salt dome. It is volume 2 of five volumes that together constitute the final report of the Danish utilities' salt dome investigations. The purpose of the work was to procure a more detailed knowledge of the geology of salt domes in North Jutland on example of Mors. The Mors dome is oval with the two axes of approx. 12.5 km and 8 km respectively. Two deep wells have been drilled into the salt. These wells reach 3400-3500 m below surface. Until a depth of about 3200 m Erslev 2 passes through rock salt of Zechstein 1 which is the oldest evaporite series. However, it could also be interlayed with the slightly younger Zechstein 2. At about 3200 m a marker layer was met with Zechstein 2 salt below. Interpretation of cores and results of downhole electromagnetic and borehole gravimetric measurements show that there is a large area around Erslev 2 which consists of very pure sodium chloride with traces of anhydrite (calcium, sulphate) 1-3%. This area is used for the repository design and safety evaluation. The hydrological conditions existing in the strata above the salt dome (caprock) have been investigated with the help of four hydrogeological wells, placed two each, on two different sites. The cores themselves were taken at various depths in all four holes. With these laboratory methods it has been possible to measure data relevant to hydrology - such as porosity and permeability - as well as geochemistry. (BP)

Salt brickwork as long-term sealing in salt formations

International Nuclear Information System (INIS)

Walter, F.; Yaramanci, U.

1993-01-01

Radioactive wastes can be disposed of in deep salt formations. Rock salt is a suitable geologic medium because of its unique characteristics. Open boreholes, shafts and drifts are created to provide physical access to the repository. Long-term seals must be emplaced in these potential pathways to prevent radioactive release into the biosphere. The sealing materials must be mechanically and, most important, geochemically stable within the host rock. Salt bricks made from compressed salt-powder are understood to be the first choice long-term sealing material. Seals built of salt bricks will be ductile. Large sealing systems are built by combining the individual bricks with mortar. Raw materials for mortar are fine-grained halite powder and ground saliferous clay. This provides for the good adhesive strength of the mortar to the bricks and the high shear-strength of the mortar itself. To test the interaction of rock salt with an emplaced long-term seal, experiments will be carried out in situ, in the Asse salt mine in Germany. Simple borehole sealing experiments will be performed in horizontal holes and a complicated drift sealing experiment is planned, to demonstrate the technology of sealing a standard size drift or shaft inside a disturbed rock mass. Especially, the mechanical stability of the sealing system has to be demonstrated

Brine migration in salt and its implications in the geologic disposal of nuclear waste

International Nuclear Information System (INIS)

Jenks, G.H.; Claiborne, H.C.

1981-12-01

This report respresents a comprehensive review and analysis of available information relating to brine migration in salt surrounding radioactive waste in a salt repository. The topics covered relate to (1) the characteristics of salt formations and waste packages pertinent to considerations of rates, amounts, and effects of brine migration, (2) experimental and theoretical information on brine migration, and (3) means of designing to minimize any adverse effects of brine migration. Flooding, brine pockets, and other topics were not considered, since these features will presumably be eliminated by appropriate site selection and repository design. 115 references

Environmental effects on corrosion in the Tuff repository

International Nuclear Information System (INIS)

Beavers, J.A.; Thompson, N.G.

1990-02-01

Cortest Columbus is investigating the long-term performance of container materials used for high-level waste packages as part of the information needed by the Nuclear Regulatory Commission to assess the Department of Energy's application to construct a geologic repository for high-level radioactive waste. The scope of work consists of employing short-term techniques, to examine a wide range of possible failure modes. Long-term tests are being used to verify and further examine specific failure modes identified as important by the short-term studies. The original focus of the program was on the salt repository but the emphasis was shifted to the Tuff repository. This report summarizes the results of a literature survey performed under Task 1 of the program. The survey focuses on the influence of environmental variables on the corrosion behavior of candidate container materials for the Tuff repository. Environmental variables considered include: radiation, thermal and microbial effects. 80 refs., 44 figs., 44 tabs

Interactions between mobilized radionuclides and secondary phases in final repository-relevant formation aquifers. Final report; Wechselwirkung mobilisierter Radionuklide mit sekundaeren Phasen in endlagerrelevanten Formationswaessern. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Curtius, H.; Kaiser, G.; Paparigas, Z.; Hansen, B.; Neumann, A.; Klinkenberg, M.; Mueller, E.; Bruecher, H.; Bosbach, D.

2010-10-15

The report on interactions between mobilized radionuclides and secondary phases in final repository-relevant formation aquifers covers the following issues: scope of study, leaching experiments, secondary phases, incorporation and sorption studies, summary and prospects. The results show that the investigated spent fuels dissolve instantaneously in contact with the repository-relevant aquifers in presence of iron ions. For the elements Cs and Sr no re-immobilization was observed. These elements have to be considered as mobile species in the radionuclide source term. The secondary phases due to corrosion processes are radionuclide sinks, i.e. actinides are re-immobilized, the retention mechanisms were clarified. The studies with irradiated nuclear fuel show that the uranium/silicon containing phases effect the molar solubility of actinides.

The HAW project. Demonstrative disposal of high-level radioactive wastes in the Asse salt mine

International Nuclear Information System (INIS)

Rothfuchs, T.; Duijves, K.

1988-04-01

Since 1968 the GSF has been carrying out research and development programs for the final disposal of high-level radioactive waste (HAW) in salt formations. The heat producing waste has been simulated so far by means of electrical heaters and also cobalt-60-sources. In order to improve the final concept for HAW disposal in salt formations the complete technical system of an underground repository is to be tested in a one-to-one scale test facility. To satisfy the test objectives thirty high radioactive canisters containing the radionuclides Cs-137 and Sr-90 will be emplaced in six boreholes located in two test galleries at the 800 m-level in the Asse salt mine. The duration of testing will be approximately five years. For the handling of the radioactive canisters and their emplacement into the boreholes a system consisting of transportation casks, transportation vehicle, disposal machine, and borehole slider will be developed and tested. The actual scientific investigation program is based on the estimation and observation of the interaction between the radioactive canisters and the rock salt. This program includes measurement of thermally and radiolytically induced water and gas release from the rock salt and the radiolytical decomposition of salt minerals. Also the thermally induced stress and deformation fields in the surrounding rock mass will be investigated carefully. (orig./HP)

Comparison of the intermediate storage periods and areas required for final storage of high-level radioactive waste and spent fuel in various types of host rock

International Nuclear Information System (INIS)

Mueller-Hoeppe, N.; Lerch, C.; Jobmann, M.; Filbert, W.

2005-01-01

The present new version of the German concept for radioactive waste and spent fuel management is based on the assumption that a repository for high-level waste and spent fuel will not be required until 2030. One reason frequently given for this date is the intermediate storage period of at least forty years to allow the very high initial heat generation to decay. However, calculations performed by the authors have shown that the minimum intermediate storage period for a repository in rock salt is only between four and nineteen years, depending on the final storage concept and the load of the waste package. In clay as a host rock, the minimum intermediate storage times were calculated to be between 31 and 142 years; the same time spans are expected to apply to final storage in magmatic rock, such as granite. The maximum permissible loads of a container holding spent fuel in salt are many times those in clay and granite, respectively. It was also seen that the area requirement for final storage of the same waste structures is roughly a factor of ten higher in clay than in salt. The differences between granite and salt are similar. The reasons for these grave differences, on the one hand, are the better thermal conductivity of salt and, on the other hand, the better heat tolerance of the crushed salt used as backfill material compared to that of bentonite used in the clay and granite concepts. While salt will allow temperatures of up to 200 C, the maximum temperature in bentonite is limited to 100 C. (orig.)

Methods of characterization of salt formations in view of spent fuel final disposal

International Nuclear Information System (INIS)

Diaconu, Daniela; Balan, Valeriu; Mirion, Ilie

2002-01-01

Deep disposal in geological formations of salt, granite and clay seems to be at present the most proper and commonly adopted solution for final disposal of high-level radioactive wastes and spent fuel. Disposing such wastes represents the top-priority issue of the European research community in the field of nuclear power. Although seemingly premature for Romanian power system, the interest for final disposal of spent fuel is justified by the long duration implied by the studies targeting this objective. At the same time these studies represent the Romanian nuclear research contribution in the frame of the efforts of integration within the European research field. Although Romania has not made so far a decision favoring a given geological formation for the final disposal of spent fuel resulting from Cernavoda NPP, the most generally taken into consideration appears the salt formation. The final decision will be made following the evaluation of its performances to spent fuel disposal based on the values of the specific parameters of the geological formation. In order to supply the data required as input parameters in the codes of evaluation of the geological formation performances, the INR Pitesti initiated a package of modern and complex methodologies for such determinations. The studies developed so far followed up the special phenomenon of salt convergence, a phenomenon characteristic for only this kind of rock, as well as the radionuclide migration. These studies allow a better understanding of these processes of upmost importance for disposal's safety. The methods and the experimental installation designed and realized at INR Pitesti aimed at determination of thermal expansion coefficient, thermal conductivity, specific heat, which are all parameters of high specific interest for high level radioactive waste or spent fuel disposal. The paper presents the results of these studies as well as the methodologies, the experimental installations and the findings

The procedure of alternative site selection within the report of the study group on the radioactive waste final repository selection process (AKEnd)

International Nuclear Information System (INIS)

Brenner, M.

2005-01-01

The paper discusses the results of the report of the study group on the radioactive waste final repository selection process with respect to the alternative site selection procedure. Key points of the report are the long-term safety, the alternativity of sites and the concept of one repository. The critique on this report is focussed on the topics site selection and licensing procedures, civil participation, the factor time and the question of cost

A Safety Case Approach for Deep Geologic Disposal of DOE HLW and DOE SNF in Bedded Salt - 13350

Energy Technology Data Exchange (ETDEWEB)

Sevougian, S. David [Advanced Nuclear Energy Programs Group, Sandia National Laboratories, P.O. Box 5800, Albuquerque, NM 87185 (United States); MacKinnon, Robert J. [Advanced Nuclear Energy Programs Group, Sandia National Laboratories, P.O. Box 5800, Albuquerque, NM 87185 (United States); Leigh, Christi D. [Defense Waste Management Programs Group, Sandia National Laboratories, P.O. Box 5800, Albuquerque, NM 87185 (United States); Hansen, Frank D. [Geoscience Research and Applications Group, Sandia National Laboratories, P.O. Box 5800, Albuquerque, NM 87185 (United States)

2013-07-01

The primary objective of this study is to investigate the feasibility and utility of developing a defensible safety case for disposal of United States Department of Energy (U.S. DOE) high-level waste (HLW) and DOE spent nuclear fuel (SNF) in a conceptual deep geologic repository that is assumed to be located in a bedded salt formation of the Delaware Basin [1]. A safety case is a formal compilation of evidence, analyses, and arguments that substantiate and demonstrate the safety of a proposed or conceptual repository. We conclude that a strong initial safety case for potential licensing can be readily compiled by capitalizing on the extensive technical basis that exists from prior work on the Waste Isolation Pilot Plant (WIPP), other U.S. repository development programs, and the work published through international efforts in salt repository programs such as in Germany. The potential benefits of developing a safety case include leveraging previous investments in WIPP to reduce future new repository costs, enhancing the ability to effectively plan for a repository and its licensing, and possibly expediting a schedule for a repository. A safety case will provide the necessary structure for organizing and synthesizing existing salt repository science and identifying any issues and gaps pertaining to safe disposal of DOE HLW and DOE SNF in bedded salt. The safety case synthesis will help DOE to plan its future R and D activities for investigating salt disposal using a risk-informed approach that prioritizes test activities that include laboratory, field, and underground investigations. It should be emphasized that the DOE has not made any decisions regarding the disposition of DOE HLW and DOE SNF. Furthermore, the safety case discussed herein is not intended to either site a repository in the Delaware Basin or preclude siting in other media at other locations. Rather, this study simply presents an approach for accelerated development of a safety case for a potential

A Safety Case Approach for Deep Geologic Disposal of DOE HLW and DOE SNF in Bedded Salt - 13350

International Nuclear Information System (INIS)

Sevougian, S. David; MacKinnon, Robert J.; Leigh, Christi D.; Hansen, Frank D.

2013-01-01

The primary objective of this study is to investigate the feasibility and utility of developing a defensible safety case for disposal of United States Department of Energy (U.S. DOE) high-level waste (HLW) and DOE spent nuclear fuel (SNF) in a conceptual deep geologic repository that is assumed to be located in a bedded salt formation of the Delaware Basin [1]. A safety case is a formal compilation of evidence, analyses, and arguments that substantiate and demonstrate the safety of a proposed or conceptual repository. We conclude that a strong initial safety case for potential licensing can be readily compiled by capitalizing on the extensive technical basis that exists from prior work on the Waste Isolation Pilot Plant (WIPP), other U.S. repository development programs, and the work published through international efforts in salt repository programs such as in Germany. The potential benefits of developing a safety case include leveraging previous investments in WIPP to reduce future new repository costs, enhancing the ability to effectively plan for a repository and its licensing, and possibly expediting a schedule for a repository. A safety case will provide the necessary structure for organizing and synthesizing existing salt repository science and identifying any issues and gaps pertaining to safe disposal of DOE HLW and DOE SNF in bedded salt. The safety case synthesis will help DOE to plan its future R and D activities for investigating salt disposal using a risk-informed approach that prioritizes test activities that include laboratory, field, and underground investigations. It should be emphasized that the DOE has not made any decisions regarding the disposition of DOE HLW and DOE SNF. Furthermore, the safety case discussed herein is not intended to either site a repository in the Delaware Basin or preclude siting in other media at other locations. Rather, this study simply presents an approach for accelerated development of a safety case for a potential

An approach to selecting routes over which to transport excess salt from the Deaf Smith County Site

International Nuclear Information System (INIS)

1987-09-01

This report presents an approach to be utilized in the identification of rail and/or highway routes for the disposal of waste salt and other salt contaminated material from repository construction. Relevant issues regarding salt transport also are identified. The report identifies a sequence of activities that precede actual route selection, i.e., final selection of a salt disposal method and its location, refined estimates of salt shipment volume and schedule, followed by selection of rail or truck or a combination thereof, as the preferred transport mode. After these factors are known, the route selection process can proceed. Chapter 2.0 of this report identifies directives and requirements that potentially could affect salt transport from the Deaf Smith site. A summary of salt disposal alternatives and reference cases is contained in Chapter 3.0. Chapter 4.0 identifies and discusses current methods of salt handling and transport in the United States, and also provides some perspective as to the volume of excess salt to be transported from the Deaf Smith site relative to current industry practices. Chapter 5.0 identifies an approach to the salt transportation issue, and suggests one system for evaluating alternative highway routes for truck shipments

A natural analogue for near-field behaviour in a high level radioactive waste repository in salt: the Salton Sea geothermal field, California, USA

International Nuclear Information System (INIS)

Elders, W.A.

1987-01-01

In the Salton Sea Geothermal Field (SSGF), in the sediments of the delta of the Colorado River, we are developing a three-dimensional picture of active water/rock reactions at temperatures of 0 C and salinities of 7 to 25 weight percent to produce quantitative data on mineral stabilities and mobilities of naturally-occurring radio-nuclides. The aim is to produce data to validate geochemical computer codes being developed to assess the performance of a Commercial High-Level Waste (CHLW) repository in salt. Among the findings to date are: (1) greenschist facies metamorphism is occurring; (2) brine compositions are fairly similar to those expected in candidate salt repository sites; (3) U and Th concentrations in the rocks are typical for sedimentary rocks; (4) the brines are enriched in Na, Mn, Zn, Sr, Ra Po and strongly depleted in U and Th relative to the rocks; (5) significant radioactive disequilibria exist in brines and solid phases of the SSGF. The disequilibria in the actinide series allow estimation of the rates of brine-rock interaction and understanding of hydrologic processes and radionuclide behaviour. Work is continuing emphasizing the reactions of authigenic clay minerals, epidotes, feldspars, chlorites and sulphates. So far, adapting geochemical codes to the necessary combination of high salinity and high temperature has lagged behind the natural analogue study of the SSGF so that validation is still in progress. In the future our data can be also used in validating performance assessment codes which couple geochemistry and transport processes, and in design of waste packages and back fill compositions. (author)

National waste terminal storage conceptual reference repository description

International Nuclear Information System (INIS)

Odgers, I.L.; Collings, J.L.

1981-01-01

The conceptual reference repository description (CRRD) discusses, from a conceptual engineering standpoint, the structures, systems, equipment, and operations necessary to: (1) receive unreprocessed spent fuel assemblies in standard casks; (2) unload these assemblies; (3) place them in canisters; (4) transport the canisters to underground storage locations in the salt dome; and (5) place the canisters in terminal storage. The CRRD also elaborates on the concepts for retrieval and recovery of the spent fuel after burial and describes the development of the shafts and the underground areas, as well as the supporting operational utility and administrative features of the repository

Comments on a letter by George D. DeBuchananne (US Geological Survey) regarding the use of salt domes for high-level waste disposal

International Nuclear Information System (INIS)

1984-08-01

The US Geological Survey (USGS) concluded in a letter to the US Department of Energy, dated March 7, 1981, that subsurface geologic conditions in bedded salt are more predictable and less complex than those in domal salt. This predictability is equated with the relative suitability of bedded and domal salt as repository host media. This report comments on the USGS letter. The key points made are as follows: Complexities which may exist in the geologic setting of a salt dome (or other potential host medium) should not a priori preclude the dome from being an acceptable host medium for a high-level waste (HLW) repository. Predictability, as used by the USGS, focused on the spatial extrapolation of information on geologic conditions and should not be confused with predicting the performance of a repository. Notwithstanding the general characteristics of bedded and domal salt, there are salt domes whose individual characteristics should make them as acceptable as potential bedded salt areas for HLW repository sites. Complexities which may occur in the geologic setting of a salt dome can be explored and characterized with sufficient accuracy by available techniques

Granular Salt Summary: Reconsolidation Principles and Applications

Energy Technology Data Exchange (ETDEWEB)

Hansen, Frank; Popp, Till; Wieczorek, Klaus; Stuehrenberg, Dieter

2014-07-01

The purposes of this paper are to review the vast amount of knowledge concerning crushed salt reconsolidation and its attendant hydraulic properties (i.e., its capability for fluid or gas transport) and to provide a sufficient basis to understand reconsolidation and healing rates under repository conditions. Topics covered include: deformation mechanisms and hydro-mechanical interactions during reconsolidation; the experimental data base pertaining to crushed salt reconsolidation; transport properties of consolidating granulated salt and provides quantitative substantiation of its evolution to characteristics emulating undisturbed rock salt; and extension of microscopic and laboratory observations and data to the applicable field scale.

1972 preliminary safety analysis report based on a conceptual design of a proposed repository in Kansas

International Nuclear Information System (INIS)

Blomeke, J.O.

1977-08-01

This preliminary safety analysis report is based on a proposed Federal Repository at Lyons, Kansas, for receiving, handling, and depositing radioactive solid wastes in bedded salt during the remainder of this century. The safety analysis applies to a hypothetical site in central Kansas identical to the Lyons site, except that it is free of nearby salt solution-mining operations and bore holes that cannot be plugged to Repository specifications. This PSAR contains much information that also appears in the conceptual design report. Much of the geological-hydrological information was gathered in the Lyons area. This report is organized in 16 sections: considerations leading to the proposed Repository, design requirements and criteria, a description of the Lyons site and its environs, land improvements, support facilities, utilities, different impacts of Repository operations, safety analysis, design confirmation program, operational management, requirements for eventually decommissioning the facility, design criteria for protection from severe natural events, and the proposed program of experimental investigations

1972 preliminary safety analysis report based on a conceptual design of a proposed repository in Kansas

Energy Technology Data Exchange (ETDEWEB)

Blomeke, J.O.

1977-08-01

This preliminary safety analysis report is based on a proposed Federal Repository at Lyons, Kansas, for receiving, handling, and depositing radioactive solid wastes in bedded salt during the remainder of this century. The safety analysis applies to a hypothetical site in central Kansas identical to the Lyons site, except that it is free of nearby salt solution-mining operations and bore holes that cannot be plugged to Repository specifications. This PSAR contains much information that also appears in the conceptual design report. Much of the geological-hydrological information was gathered in the Lyons area. This report is organized in 16 sections: considerations leading to the proposed Repository, design requirements and criteria, a description of the Lyons site and its environs, land improvements, support facilities, utilities, different impacts of Repository operations, safety analysis, design confirmation program, operational management, requirements for eventually decommissioning the facility, design criteria for protection from severe natural events, and the proposed program of experimental investigations. (DLC)

In-situ test programs related to design and construction of high-level nuclear waste (HLW) deep geologic repositories. Final report (Task 2), June 1981-November 1982

International Nuclear Information System (INIS)

Roberds, W.; Bauhof, F.; Gonano, L.

1983-03-01

The media and sites considered include (1) basalt at Hanford, Washington; (2) tuff at Yucca Mountain, Nevada Test Site; (3) domal salt at specific Gulf Coast sites; (4) bedded salt at an unspecified site; and (5) granite at an unspecified site. A licensing perspective is outlined and a defensible rationale developed and utilized for the test selection process. This rationale essentially consists of: establishing the information needs for construction authorization; assessing the relevant capabilities of available tests; and matching the capabilities of specific tests to the perceived information needs. The information needs at any time consist of the additional information (if any) needed in order to predict satisfactory repository system performance with the required level of confidence, and thus are a function of: the significance of the repository engineered components and site characteristics to system performance; the currently available information, which may be supplemented with time; and the acceptable level of confidence in satisfactory performance for each licensing step. Determination of the acceptable levels of confidence and the significance of repository system components is outside the scope of this report. Suitable assumptions have thus been made regarding the development of information needs for construction authorization by the time of initial site submittals. Tests which are available and respond to the perceived media/site specific information needs, either by simulation or assessment of site characteristics, are identified and their capabilities assessed. Specific in situ tests are investigated and described in detail. Research and development which might be effective in improving test capabilities have been recommended

Radioactive waste and special waste disposal in salt domes - phoney waste management solutions

International Nuclear Information System (INIS)

Grimmel, E.

1990-01-01

The paper tries to make aware of the fact that an indefinite safe disposal of anthropogeneous wastes in underground repositories is impossible. Suspicion is raised that the Gorleben-Rambow salt dome has never been studied for its suitability as a repository, but that it was simply taken for granted. Safety analyses are meant only to conceal uncertainty. It is demanded to immediately opt out of the ultimate disposal technique for radioactive and special wastes in salt caverns. (DG) [de

Monitoring a repository for high-level radioactive waste in Germany. Possibilities and limits

International Nuclear Information System (INIS)

Jobmann, M.; Haverkamp, B.; Eilers, G.

2011-01-01

Pursuant to the new BMU safety requirements of September 2010 imposed upon the final storage of radioactive waste generating heat, the operator of a repository in Germany must establish a monitoring program which furnishes relevant measured information during the operations phase and for a defined period of time after closure of the repository. Within the framework of a feasibility study, an assessment basis was established to show in what format information about the status of a closed repository mine could be obtained technically without impairing the safety of barriers, for instance, by cable ducts. As a conceptual design basis, processes and measured quantities relevant to monitoring were attributed to the components of the current safety demonstration concept. For one model variant, monitoring possibilities of these processes were shown on the basis of monitoring modules. Some first experiments are being carried out in European underground laboratories about the use of wireless transmission systems in the repository area. On the basis of those activities, experiments could also be designed in the German exploratory mine of Gorleben in order to examine to what extent information obtained by monitoring could be transmitted in a wireless mode in rock salt formations. As far as the autonomous supply of electricity to measurement systems is concerned, which must be guaranteed on a long-term basis, there is now a possibility of using thermoelectric isotope generators or betavoltaic batteries. (orig.)

HAW project. Demonstrative disposal of high-level radioactive wastes in the Asse salt mine

International Nuclear Information System (INIS)

Rothfuchs, T.; Duijves, K.; Stippler, R.

1988-01-01

Since 1968 the GSF has been carrying out research and development programs for the final disposal of high-level radioactive waste (HAW) in salt formations. The heat producing waste has been simulated so far by means of electrical heaters and also cobalt-60-sources. In order to improve the final concept for HAW disposal in salt formations the complete technical system of an underground repository is to be tested in an one-to-one scale test facility. To satisfy the test objectives thirty high radioactive canisters containing the radionuclides Cs-137 and Sr-90 will be emplaced in six boreholes located in two test galleries at the 800 m-level in the Asse salt mine. The duration of testing will be approximately five years. For the handling of the radioactive canisters and their emplacement into the boreholes a system consisting of transportation casks, transportation vehicle, disposal machine, and borehole slider will be developed and tested. The actual scientific investigation program is based on the estimation and observation of the interaction between the radioactive canisters and the rock salt. This program includes measurement of thermally and radiolytically induced water and gas release from the rock salt and the radiolytical decomposition of salt minerals. Also the thermally induced stress and deformation fields in the surrounding rock mass will be investigated carefully. The project is funded by the BMFT and the CEC and carrier out in close co-operation with the Netherlands Energy Research Foundation (ECN)

Basic repository environmental assessment design basis, Davis Canyon site

International Nuclear Information System (INIS)

1984-01-01

This study examines the engineering factors and costs associated with the construction, operation, and decommissioning of a high-level nuclear waste repository in salt in the Paradox Basin in Davis Canyon, Utah. The study assumes a repository capacity of 36,000 metric tons of heavy metal (MTHM) of unreprocessed spent fuel and 36,000 MTHM of commercial high-level reprocessing waste, along with 7,020 canisters of defense high-level reprocessing waste and associated quantities of remote- and contact-handled transuranic waste (TRU). With the exception of TRU, all the waste forms are placed in 300- to 1,000-year-life carbon-steel waste packages in a collected waste handling and packaging facility (WHPF), which is also described. The construction, operation, and decommissioning of the proposed repository is estimated to cost approximately $5.49 billion. Costs include those for the collocated WHPF, engineering, and contingency, but exclude waste form assembly and shipment to the site and waste package fabrication and shipment to the site. These costs reflect the relative average wage rates of the region and the relatively sound nature of the salt at this site. Construction would require an estimated 7.75 years. Engineering factors and costs are not strongly influenced by environmental considerations. 50 refs., 24 figs., 20 tabs

Basic repository environmental assessment design basis, Lavender Canyon site

International Nuclear Information System (INIS)

1988-01-01

This study examines the engineering factors and costs associated with the construction, operation, and decommissioning of a high-level nuclear waste repository in salt in the Paradox Basin in Lavender Canyon, Utah. The study assumes a repository capacity of 36,000 metric tons of heavy metal (MTHM) of unreprocessed spent fuel and 36,000 MTHM of commercial high-level reprocessing waste, along with 7020 canisters of defense high-level reprocessing waste and associated quantities of remote- and contact-handled transuranic waste (TRU). With the exception of TRU, all the waste forms are placed in 300- to 1000-year-life carbon-steel waste packages in a collocated waste handling and packaging facility (WHPF), which is also described. The construction, operation, and decommissioning of the proposed repository is estimated to cost approximately $5.51 billion. Costs include those for the collocated WHPP, engineering, and contingency, but exclude waste form assembly and shipment to the site and waste package fabrication and shipment to the site. These costs reflect the relative average wage rates of the region and the relatively sound nature of the salt at this site. Construction would require an estimated 7.75 years. Engineering factors and costs are not strongly influenced by environmental considerations. 51 refs., 24 figs., 20 tabs

Roadmap for disposal of Electrorefiner Salt as Transuranic Waste.

Energy Technology Data Exchange (ETDEWEB)

Rechard, Robert P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Trone, Janis R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kalinina, Elena Arkadievna [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wang, Yifeng [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hadgu, Teklu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sanchez, Lawrence C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-12-01

The experimental breeder reactor (EBR-II) used fuel with a layer of sodium surrounding the uranium-zirconium fuel to improve heat transfer. Disposing of EBR-II fuel in a geologic repository without treatment is not prudent because of the potentially energetic reaction of the sodium with water. In 2000, the US Department of Energy (DOE) decided to treat the sodium-bonded fuel with an electrorefiner (ER), which produces metallic uranium product, a metallic waste, mostly from the cladding, and the salt waste in the ER, which contains most of the actinides and fission products. Two waste forms were proposed for disposal in a mined repository; the metallic waste, which was to be cast into ingots, and the ER salt waste, which was to be further treated to produce a ceramic waste form. However, alternative disposal pathways for metallic and salt waste streams may reduce the complexity. For example, performance assessments show that geologic repositories can easily accommodate the ER salt waste without treating it to form a ceramic waste form. Because EBR-II was used for atomic energy defense activities, the treated waste likely meets the definition of transuranic waste. Hence, disposal at the Waste Isolation Pilot Plant (WIPP) in southern New Mexico, may be feasible. This report reviews the direct disposal pathway for ER salt waste and describes eleven tasks necessary for implementing disposal at WIPP, provided space is available, DOE decides to use this alternative disposal pathway in an updated environmental impact statement, and the State of New Mexico grants permission.

Ventilation planning for a prospective nuclear waste repository

International Nuclear Information System (INIS)

Wallace, K.G. Jr.

1987-01-01

In 1982, the US Congress passed the Nuclear Waste Policy Act to provide for the development of underground repositories for spent nuclear fuel. This development will be managed by the United States Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository; those sites were: (1) A site in volcanic tuff located at Yucca Mountain in Nevada, (2) a site in bedded salt located in Deaf Smith County in Texas, and (3) a site in basalt located in Hanford, Washington. At present conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation systems designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be re-established to allow re-entry into previously closed rooms for the purpose of inspection, maintenance or retrieval

Safety analysis of the transportation of radioactive waste to the Konrad final repository

International Nuclear Information System (INIS)

Sentuc, F.N.; Bruecher, W.

2010-01-01

A transport risk assessment study has been conducted for transport of radioactive waste with negligible heat-generation to the German final repository Konrad. This study is a revision of the former Konrad Transport Study performed by GRS in 1991 implementing updated waste data among other improved methods and assumptions for the purpose of a more realistic approach to risk assessment. The first part of the transport risk assessment study concerns the radiological consequences from normal (accident-free) transportation of radioactive material, i.e. the radiation exposure of transport personnel and the public. Based on the assessed detailed information on transport arrangements and on the average number and radiological characteristics of waste packages the maximum annual effective doses for the representative persons were estimated. The risk associated with transport incidents and accidents has been quantified for the area within a radius of 25 km around the repository site. The probabilistic method adopted in this study considers parameters as the frequency and severity of railway or road accidents, characteristics of radioactive waste and transport packagings and the frequency of atmospheric dispersion conditions. From a large set of parameter combinations the spectrum of potential radiological consequences and of the associated probability of occurrence was assessed. (orig.)

What do we mean by a cold repository?

International Nuclear Information System (INIS)

Halsey, W.G.

1994-01-01

The topic of thermal loading of a potential repository at Yucca Mountain in Nevada has been the subject of intense discussion within the project technical community. While terms such as ''Hot Repository'' and ''Cold Repository'' are frequently used, they have not been clearly defined. In particular, the definition of a cold repository has remained the opinion of each individual. This has led to confusion and misunderstanding. In this paper, a number of observed definitions for a cold repository are discussed along with the technical implications, assumptions and inconsistencies. Finally, a common language is suggested

Geohydrology surrounding a potential high-level nuclear waste repository in the Paradox Basin, Utah

International Nuclear Information System (INIS)

Brandstetter, A.; Kroitoru, L.; Andrews, R.W.; Thackston, J.W.

1984-01-01

The Gibson Dome area in the Paradox Basin in southeastern Utah has been identified as a potential location for a high-level nuclear waste repository on the basis of an adequate thickness of bedded salt formations at desirable depths, suitable topography for surface facilities, few known archaeological sites, less resource potential than otherwise similar areas, and long-term geologic and tectonic stability. The area appears also suitable from a geohydrologic viewpoint, on the basis of data collected and analyses performed to date. The upper, near-surface, geologic formations include both regionally continuous water-bearing formations and locally perched ground waters that discharge into nearby surface streams and into the Colorado River. Below the Paradox salts, the formations of interest with respect to repository safety include regionally continuous water-bearing formations, with the Leadville limestone being the principal water-transmitting unit. Flows in all water-bearing formations are essentially horizontal. If a vertical connection were established through a potential repository, hydraulic gradients indicate that the flow would first be downward from the upper to the lower formations and then laterally, principally in the Leadville formation. There are some indications that minor leakage could occur into the Colorado River as close as Cataract Canyon, about 20 to 25 km (10 to 15 miles) from a potential repository location in Davis Canyon, or into the Colorado River in Marble Canyon (Arizona), about 240 km (150 miles) to the southwest. Groundwater flow from a repository to these locations is unlikely, however, since water would first have to penetrate the essentially impermeable salt layers before it would reach the Leadville formation. 11 references, 4 figures

The alternative site selection procedure as covered in the report by the Repository Site Selection Procedures Working Group

International Nuclear Information System (INIS)

Brenner, M.

2005-01-01

The 2002 Act on the Regulated Termination of the Use of Nuclear Power for Industrial Electricity Generation declared Germany's opting out of the peaceful uses of nuclear power. The problem of the permanent management of radioactive residues is becoming more and more important also in the light of that political decision. At the present time, there are no repositories offering the waste management capacities required. Such facilities need to be created. At the present stage, eligible repository sites are the Konrad mine, a former iron ore mine near Salzgitter, and the Gorleben salt dome. While the fate of the Konrad mine as a repository for waste generating negligible amounts of heat continues to be uncertain, despite a plan approval decision of June 2002, the Gorleben repository is still in the planning phase, at present in a dormant state, so to speak. The federal government expressed doubt about the suitability of the Gorleben site. Against this backdrop, the Federal Ministry for the Environment, Nature Conservation, and Nuclear Safety in February 1999 established AkEnd, the Working Group on Repository Site Selection Procedures. The Group was charged with developing, based on sound scientific criteria, a transparent site selection procedure in order to facilitate the search for repository sites. The Working Group presented its final report in December 2002 after approximately four years of work. The Group's proposals about alternative site selection procedures are explained in detail and, above all, reviewed critically. (orig.)

Research project for the determination of the suitability of the mine ''Konrad'' as a final repository for radioactive waste products

International Nuclear Information System (INIS)

1984-01-01

A feasibility study of the Konrad mine for its use as a final repository for radioactive waste products was performed in 1978, 1979 and 1980. The report summarizes the most important results gained in the fields of geosciences and technical aspects of disposal operations

Modelling of the thermomechanical behaviour of salt rock

International Nuclear Information System (INIS)

Albers, G.; Graefe, V.; Korthaus, E.; Pudewillis, A.; Prij, J.

1986-01-01

The modelling of the thermomechanical behaviour of salt rock is examined, with respect to the disposal of radioactive waste in salt formations. The calculation methods and programmes currently available for the modelling are described. Some examples are given of calculations carried out in parallel with tests. Some results of modelling calculations for a repository are presented by way of illustration. (U.K.)

Nye County, Nevada 1992 nuclear waste repository program: Program overview. Final report

International Nuclear Information System (INIS)

1998-01-01

The purpose of this document is to provide an overview of the Nye County FY92 Nuclear Waste Repository Program (Program). Funds to pay for Program costs will come from the Federal Nuclear Waste Fund, which was established under the Nuclear Waste Policy Act of 1982 (NWPA). In early 1983, the Yucca Mountain was identified as a potentially suitable site for the nation's first geologic repository for spent reactor fuel and high-level radioactive waste. Later that year, the Nye County Board of County Commissioners (Board) established the capability to monitor the Federal effort to implement the NWPA and evaluate the potential impacts of repository-related activities on Nye County. Over the last eight years, the County's program has grown in complexity and cost in order to address DOE's evolving site characterization studies, and prepare for the potential for facility construction and operation. Changes were necessary as well, in response to Congress's redirection of the repository program specified in the amendments, to the NWPA approved in 1987. In early FY 1991, the County formally established a project office to plan and implement its program of work. The Repository Project Office's (RPO) mission and functions are provided in Section 2.0. The RPO organization structure is described in Section 3.0

Geologic disposal of nuclear wastes: salt's lead is challenged

International Nuclear Information System (INIS)

Kerr, R.A.

1979-01-01

The types of radioactive waste disposal sites available are outlined. The use of salt deposits and their advantages are discussed. The reasons for the selection of the present site for the Waste Isolation Pilot Plant are presented. The possibilities of using salt domes along the Gulf Coast and not-salt rocks as nuclear waste repositories are also discussed. The sea bed characteristics are described and advantages of this type of site selection are presented

Development of a central final repository management for the coordination of the waste for Schacht Konrad from public authorities; Aufbau des zentralen Endlagerungsmanagements fuer die Koordination der Konrad-Abfaelle aus der oeffentlichen Hand

Energy Technology Data Exchange (ETDEWEB)

Graffunder, Iris; Dominke-Bendix, Carola; Waldek, Achim [Energiewerke Nord GmbH (EWN), Eggenstein-Leopoldshafen (Germany). Betriebsstaette Karlsruhe; Wunn, Christoph [admoVa Consulting GmbH, Bad Camberg (Germany)

2012-11-01

The central final repository management is supposed to fulfill the following tasks: active collaboration of Konrad contract draft, signing of internal contracts and agreements, cooperation contract with GNS, cooperation with coordination authorities, inventory taking of wastes (existing inventory and prognosis) and interim storage capacities of public authorities, development of planning and management software, optimization of the final repository documentation, container management, logistics concept, long-term disposal planning and prognosis, planning and coordination of the annual waste amount, management and documentation of disposed waste allocation, coordination of transport schedules, consulting service for waste obligations (final repository requirements, product control, documentation).

In-situ test programs related to design and construction of high-level nuclear waste (HLW) deep geologic repositories. Appendices. Final report (Task 2), June 1981-November 1982

International Nuclear Information System (INIS)

Roberds, W.; Bauhof, F.; Gonano, L.

1983-03-01

The media and sites considered include: (1) basalt at Hanford, Washington; (2) tuff at Yucca Mountain, Nevada Test Site; (3) domal salt at specific Gulf Coast sites; (4) bedded salt at an unspecified site; and (5) granite at an unspecified site. A licensing perspective is outlined and a defensible rationale developed and utilized for the test selection process. This rationale essentially consists of: establishing the information needs for construction authorization; assessing the relevant capabilities of available tests; and matching the capabilities of specific tests to the perceived information needs. The information needs at any time consist of the additional information (if any) needed in order to predict satisfactory repository system performance with the required level of confidence, and thus are a function of: the significance of the repository engineered components and site characteristics to system performance; the currently available information, which may be supplemented with time; and the acceptable level of confidence in satisfactory performance for each licensing step. Determination of the acceptable levels of confidence and the significance of repository system components is outside the scope of this report. Suitable assumptions have thus been made regarding the development of information needs for construction authorization by the time of initial site characterization reports submittals. Tests which are available and respond to the perceived media/site specific information needs, either by simulation or assessment of site characteristics, are identified and their capabilities assessed. Specific in situ tests are investigated and described in detail. Research and development which might be effective in improving tests capabilities have been recommended

Radioactive waste isolation in salt: peer review of Westinghouse Electric Corporation's report on reference conceptual designs for a repository waste package

Energy Technology Data Exchange (ETDEWEB)

Rote, D.M.; Hull, A.B.; Was, G.S.; Macdonald, D.D.; Wilde, B.E.; Russell, J.E.; Kruger, J.; Harrison, W.; Hambley, D.F.

1985-10-01

This report documents the findings of the peer panel constituted by Argonne National Laboratory to review Region A of Westinghouse Electric Corporation's report entitled Waste Package Reference Conceptual Designs for a Repository in Salt. The panel determined that the reviewed report does not provide reasonable assurance that US Nuclear Regulatory Commission (NRC) requirements for waste packages will be met by the proposed design. It also found that it is premature to call the design a ''reference design,'' or even a ''reference conceptual design.'' This review report provides guidance for the preparation of a more acceptable design document.

Uranium, thorium and trace elements in geologic occurrences as analogues of nuclear waste repository conditions

International Nuclear Information System (INIS)

Wollenberg, H.A.; Brookins, D.G.; Cohen, L.H.; Flexser, S.; Abashian, M.; Murphy, M.; Williams, A.E.

1984-01-01

Contact zones between intrusive rocks and tuff, basalt, salt and granitic rock were investigated as possible analogues of nuclear waste repository conditions. Results of detailed studies of contacts between quartz monzonite of Laramide age, intrusive into Precambrian gneiss, and a Tertiary monzonite-tuff contact zone indicate that uranium, thorium and other trace elements have not migrated significantly from the more radioactive instrusives into the country rock. Similar observations resulted from preliminary investigations of a rhyodacite dike cutting basalt of the Columbia River plateau and a kimberlitic dike cutting bedded salt of the Salina basin. This lack of radionuclide migration occurred in hydrologic and thermal conditions comparable to, or more severe than those expected in nuclear waste repository environments and over time periods of the order of concern for waste repositories. Attention is now directed to investigation of active hydrothermal systems in candidate repository rock types, and in this regard a preliminary set of samples has been obtained from a core hole intersecting basalt underlying the Newberry caldera, Oregon, where temperatures presently range from 100 to 265 0 C. Results of mineralogical and geochemical investigations of this core should indicate the alteration mineralogy and behavior of radioelements in conditions analogous to those in the near field of a repository in basalt

Radiological consequences associated with a human intrusion into a saliferous formation containing a radioactive waste repository

International Nuclear Information System (INIS)

Jacquier, P.; Raimbault, P.

1990-01-01

Assessment of the consequences of human intrusion scenarios for a repository in salt formations is very important, since this material has an undeniable economic value: it is also a propitious medium for the storage of hydrocarbons, gases, etc. In this work the scenario considers solution mining of salt for human consumption: salt is extracted from a cavern by leaching, and this enlarges the cavern and uncovers the waste, which then falls down into the sump. It was assumed that the intrusion would take place at 500 or even 2500 years after closing of the repository. High activity vitrified waste or cement enrobed alpha waste was considered. This paper sets out the assumptions made and, using simplified modelling of the phenomena, makes an estimation of the radiological consequences associated with ingestion of contaminated salt. A sensitivity/uncertainty analysis which is presented emphasises several fields in which experimental studies should be launched or pursued. (author)

Alteration of non-metallic barriers and evolution of solution chemistry in salt formations in Germany

International Nuclear Information System (INIS)

Herbert, H.J.; Becker, D.; Hagemann, S.; Meyer, Th.; Noseck, U.; Rubel, A.; Mauke, R.; Wollrath, J.

2005-01-01

Different Engineered Barrier Systems (EBS) materials considered in Germany for the sealing of repositories in salt formations are presented. Their long term behaviour in terms of interactions with salt solutions is discussed and evaluated. The discussed EBS materials are crushed salt, self sealing salt backfill, bentonite and salt concrete. Whereas the knowledge concerning the geochemical, geomechanical, hydrological and thermal behavior of crushed salt and salt concrete is well advanced further research is needed for other EBS materials. The self healing salt backfill has also been investigated in depth recently. In order to fully qualify this material large scale in situ experiments are still needed. The present knowledge on compacted bentonites in a salt environment is not yet sufficient for reliable predictions of the long-term performance in salt formations. The sealing concept of the low- and intermediate-level Radioactive Waste Repository Morsleben (ERAM) in a former rock salt and potash mine is presented. This concept is based on cementitious materials, i.e. salt concrete. The geochemical stability of different salt concretes in contact with brines expected in ERAM is addressed. It is shown how the results from leaching experiments and geochemical modelling are used in the safety analyses and how the chemical boundary conditions prevailing in the EBS influence the development of the permeability of the sealing system and thus control the radionuclide release. As a result of modelling the behaviour of the seals in the safety assessment it is shown, that the seals are corroded within a time span of about 20 000 years. The influence of the uncertainty in the model parameters on the safety of the repository was assessed by a variation of the initial permeability of the seal. The maximum dose rate resulting from the radionuclide release from ERAM is nearly independent of the variation of the initial permeability within four orders of magnitude. (authors)

Development of waste package designs for disposal in a salt repository

International Nuclear Information System (INIS)

Balmert, M.E.

1983-01-01

Three package design concepts were developed for CHLW and DHLW forms and spent fuel rods: (1) carbon steel overpack, borehole emplacement, (2) titanium clad, carbon steel reinforced overpack, borehole emplacement, and (3) carbon steel (self-shield) overpack, tunnel emplacement. For a DHLW canister with titanium clad overpack, the concept features a 9.5-cm-thick carbon steel overpack reinforcement supporting a 0.25-cm-thick titanium shell. The overall package dimensions are 84 cm diameter x 340 cm long weighing about 8.8 mtons. By contrast, a monolithic DHLW borehole package has a carbon steel overpack that is 10.4 cm thick, weighing about 9.3 mtons. The titanium clad/carbon steel reinforced borehole package is intended for remote emplacement in a vertical borehole in salt. The carbon steel overpack reinforcement provides structural integrity, primarily to resist external pressure, while the titanium overpack provides the necessary corrosion resistance to meet containment requirements. The carbon steel borehole package concept provides containment integrity for both external pressure and corrosion environments with a thicker carbon steel overpack in place of the titanium/carbon steel concept. A third concept utilizes an even greater thickness of cast steel or iron to resist external pressure and corrosion as well as reduce external shielding requirements. For example, a cast steel DHLW package would have overall dimensions of 125 cm diameter x 390 cm long, weighing 31 mtons. The purpose of this self-shield concept is to minimize handling and emplacement operations by reducing the package surface radiation dose to about 100 mrem/hr. In addition, it may serve as a shipping cask, thereby eliminating the need for a shielded hot cell at the repository for waste package assembly operations. 7 figures

The industrial organization of the repository. Pitfall or logical?; Slutfoervarets industriella organisering. Fallgrop eller foeljdriktighet?

Energy Technology Data Exchange (ETDEWEB)

Frostenson, Magnus (Dept. of Business Studies, Uppsala Univ., Uppsala (Sweden))

2010-11-15

From a systems perspective the organization of the Swedish final repository project for nuclear waste is studied. Different aspects of organization are identified in the report, covering dimensions of geographical, operative, structural, responsibility and contextual organization. Following SKB's site selection for the applications for the final repository for spent nuclear system and the closing of the surplus value agreement, issues concerning operative, structural and contextual organization tend to become particularly pressing, which is reflected in three research questions: - How will the final repository project be organized operatively and structurally over time? - Why is the final repository project organized in this way by SKB? - What kind of contextual organization takes place in the final repository project and what are the consequences of these activities? How the different industrial units of the final repository project should be run and within which structure, for example concerning ownership and integration of units, is established in the report. SKB's reasons for choosing this kind of organization are also highlighted. Apart from legal and safety-related demands that must be met together with the demands of the owners, SKB's strategic preference for insourcing conditions organizational choices. The traditional task centred operative and structural organization of SKB is also reflected in the organizational choices for the present and future units of the final depository system. Contextual organization implies deepened actor relationships between SKB's owners and SKB on the one side and the municipalities Oesthammar and Oskarshamn on the other. Through active organizing, the final repository arena 'narrows down' and the final repository issue turns into an in many respects local issue. There is a clear tendency that the roles of SKB are multiplied in order to handle the demands that central stakeholders - in particular

Tools for Managing Repository Objects

OpenAIRE

Banker, Rajiv D.; Isakowitz, Tomas; Kauffman, Robert J.; Kumar, Rachna; Zweig, Dani

1993-01-01

working Paper Series: STERN IS-93-46 The past few years have seen the introduction of repository-based computer aided software engineering (CASE) tools which may finally enable us to develop software which is reliable and affordable. With the new tools come new challenges for management: Repository-based CASE changes software development to such an extent that traditional approaches to estimation, performance, and productivity assessment may no longer suffice - if they ever...

Project Guarantee 1985. Final repository for high-level radioactive wastes: Safety report

International Nuclear Information System (INIS)

Anon.

1985-01-01

Disposal of radioactive was involves preventing releases to the biosphere for a long period of time and subsequently limiting the magnitude of releases by means of a series of safety barriers: the waste solidification matrix (borosilicate glass), massive steel canisters in highly compacted bentonite, sealing of void spacer and access routes on repository closure. The geological barriers are formed by the crystalline bed-rock and the overlying sedimentary layers. In order to perform a safety assessment the behaviour of these technical barriers and of the host rock must be understood and this understanding must be translated into quantitative models which allow calculation of repository performance. For the particular case of a Swiss repository, the main criterion is the individual dose limit of 10 mrem/year, which is given in the safety guidelines of the Swiss authorities. The procedure for the safety analysis involves examination of all scenarios which could give rise to radionuclide release from the repository. Qualitative considerations of both the magnitude of their consequences and their likelihood are used in order to identify a restricted number of scenarios for quantitative analysis

Thermophysical properties of reconsolidating crushed salt.

Energy Technology Data Exchange (ETDEWEB)

Bauer, Stephen J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Urquhart, Alexander [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-03-01

Reconsolidated crushed salt is being considered as a backfilling material placed upon nuclear waste within a salt repository environment. In-depth knowledge of thermal and mechanical properties of the crushed salt as it reconsolidates is critical to thermal/mechanical modeling of the reconsolidation process. An experimental study was completed to quantitatively evaluate the thermal conductivity of reconsolidated crushed salt as a function of porosity and temperature. The crushed salt for this study came from the Waste Isolation Pilot Plant (WIPP). In this work the thermal conductivity of crushed salt with porosity ranging from 1% to 40% was determined from room temperature up to 300°C, using two different experimental methods. Thermal properties (including thermal conductivity, thermal diffusivity and specific heat) of single-crystal salt were determined for the same temperature range. The salt was observed to dewater during heating; weight loss from the dewatering was quantified. The thermal conductivity of reconsolidated crushed salt decreases with increasing porosity; conversely, thermal conductivity increases as the salt consolidates. The thermal conductivity of reconsolidated crushed salt for a given porosity decreases with increasing temperature. A simple mixture theory model is presented to predict and compare to the data developed in this study.

The fairy tale on Asse, Gorleben and other final repositories. A never-ending story. 3. ed.

International Nuclear Information System (INIS)

Hinsch, Hermann

2013-01-01

Based on the actual problems in the final repository Asse for low- and medium-level radioactive waste the authors discusses official statements from politicians, scientists and engineers concerning the safety and risks of nuclear power, nuclear wastes, waste management and radiation hazards with respect to reality and scientific knowledge. In this context the author is talking about fairy tales that are supposed to influence the public opinion. The author's opinion is that the risks and hazards of radioactive wastes for environment and the human population are overestimated.

Transport of radioactive wastes to the planned final waste repository Konrad: Radiation exposure resulting from normal transport and radiological risks from transport accidents

International Nuclear Information System (INIS)

Lange, F.; Fett, H.J.; Gruendler, D.; Schwarz, G.

1993-01-01

Radiation exposures of members of critical groups of the general population and of transport personnel resulting from normal transport of radioactive wastes to the planned final waste repository Konrad have been evaluated in detail. By applying probabilistic safety assessment techniques radiological risks from transport accidents have been analysed by quantifying potential radiation exposures and contaminations of the biosphere in connection with their expected frequencies of occurrence. The Konrad transport study concentrates on the local region of the waste repository, where all transports converge. (orig.) [de

Retrieval effects on ventilation and cooling requirements for a nuclear waste repository

International Nuclear Information System (INIS)

Hambley, D.F.

1985-01-01

The Nuclear Waste Policy Act of 1982 (Public Law 97-425) and the regulations promulgated in Title 10, Part 60 of the Code of Federal Regulations (10CFR60) by the US Nuclear Regulatory Commission (NRC) for an underground repository for spent fuel and high level nuclear waste (HLW) require that it is possible to retrieve waste, for whatever reason, from such a facility for a period of 50 years from initial storage or until the completion of the performance confirmation period, whichever comes first. This paper considers the effects that the retrievability option mandates on ventilation and cooling systems required for normal repository operations. An example is given for a hypothetical repository in salt. 18 refs., 1 tab

Region-to-area screening methodology for the crystalline repository project

International Nuclear Information System (INIS)

1984-08-01

The ''Nuclear Waste Policy Act of 1982'' (NWPA), enacted January 7, 1983 as Public Law 97-425, confirmed the responsibility of the US Department of Energy (DOE) for management of high-level radioactive waste. The NWPA directed the DOE to provide safe facilities for isolation of high-level radioactive waste from the environment in federally owned and federally licensed repositories. To achieve the goals of providing licensed repositories for high-level radioactive waste, a technical program has been developed by the DOE to meet all relevant radiological protection criteria and other requirements. By March 1987, the NWPA requires the DOE to recommend to the President a single site, chosen from five nominated sites for construction of the first repository. Rock types being considered as potential hosts for the first repository include salt, basalt, and tuff. The NWPA also requires the DOE to select three candidate sites, chosen from five nominated sites to be recommended to the President by July 1989, as possible locations for the second repository. Potential host rock types for the second federal repository will include crystalline rock. This document outlines the methodology for region-to-area screening of exposed crystalline rock bodies for suitability as sites for further study. 17 refs., 14 figs., 2 tabs

Initial design process of the repository

International Nuclear Information System (INIS)

Osmanlioglu, A.E.

2001-01-01

The concept of the final disposal of high level wastes is to isolate the waste from the biosphere for extremely long periods of time by emplacement of wastes into deep stable geological formations. Several geological formations have been considered as candidate host environments for high level waste disposal and several techniques have been developed for repository design. In this study, interrelationships of main parameters of a general repository design have been defined and effective parameters are shown at each step. Initial design process is based on the long term stability of underground openings as disposal galleries. For this reason, this design process includes two main analyses: mechanical analysis and thermal analysis. Each of the analysis systems is directly related to each other by technical precautions. As a result of this design process, general information about the acceptable depth of the repository, layout and emplacement pattern can be taken. Final design study can be established on the result of initial design process. (author)

Final storage of radioactive waste in Germany. Waste arisings and availability of a repository as seen by an electricity utility

International Nuclear Information System (INIS)

Broeskamp, H.; Brammer, K.J.; Graf, R.

2004-01-01

The management of waste arising in the operation of nuclear power plants has been taken into account since the beginnings of the peaceful uses of nuclear power in Germany. As early as in 1957, a memorandum of the German Advisory Committee on Atomic Energy contains a reference to the need for safe disposal of radioactive waste. Legislation adopted the suggestion and laid down some provisions on the safe utilization of radioactive materials as early as in the Atomic Energy Act of December 23, 1959. In connection with the nuclear waste management center, the Federal Republic also looked for a suitable site for a repository. After thorough site selection proceedings by the federal government and the state of Lower Saxony, the Lower Saxony state government in 1977 defined Gorleben as the site. The decision has been preceded by a three-stage selection process in which more than 140 sites had been investigated. Exploration of the Gorleben site began in 1979 and was interrupted on October 1, 2000 to clarify conceptual and safety-related doubts of the federal government. The German Federal Ministry for the Environment (BMU) seeks to make a repository (for high-level waste) available in 2030. Technically, it is still possible to commission a repository for waste generating heat at Gorleben after 2025 if the salt dome is found to be suitable after speedy conclusion of the exploration work. Reference is made to foreseeable problem areas. Another project pursued by the federal government is the use of the Konrad mine as a repository for low and medium-level radioactive waste. After well over twenty years, the plans approval decision was made in May 2002 and is at present the subject of litigation. On the basis of the data presented about the expected arisings of waste generating no heat in combination with the possible start of emplacement in Konrad in 2013, detailed results are presented. (orig.) [de

Basic repository environmental assessment design basis: Deaf Smith County site

International Nuclear Information System (INIS)

1988-03-01

This study examines the engineering factors and costs associated with the construction, operation, and decommissioning of a high-level nuclear waste repository in salt in the Palo Duro Basin in Deaf Smith County, Texas. The study assumes a repository capacity of 36,000 metric tons of heavy metal (MTHM) of unreprocessed spent fuel and 36,000 MTHM of commercial high-level reprocessing waste, along with 7,020 canisters of defense high-level reprocessing waste and associated quantities or remote- and contact-handled transuranic waste (TRU). With the exception of TRU, all the waste forms are placed in 300- to 1000-year-life carbon-steel waste packages in a collocated waste handling and packaging facility (WHPF), which is also described. The construction, operation, and decommissioning of the proposed repository is estimated to cost approximately $4.64 billion. Costs include those for the collocate WHPF, engineering, and contingency, but exclude waste form assembly and shipment to the site and waste package fabrication and shipment to the site. These costs reflect the relative average wage rates of the region, the relatively easy access to the site, and the relatively weak nature of the salt at this site. Construction would require an estimated 7 to 7.5 years. Engineering factors and costs are not strongly influenced by environmental considerations. 62 refs., 24 figs., 20 tabs

In situ investigations on the impact of heat production and gamma radiation with regard to high-level radioactive waste disposal in rock salt formations

International Nuclear Information System (INIS)

Rothfuchs, T.

1986-01-01

Deep geological formations especially rock salt formations, are considered worldwide as suitable media for the final disposal of radioactive high-level waste (HLW). In the Federal Republic of Germany, the Institut fur Tieflagerung of the Gesellschaft fur Strahlen- und Umweltforschung mbH Munchen operates the Asse Salt Mine as a pilot facility for testing the behavior of an underground nuclear waste repository. The tests are performed using heat and radiation sources to simulate disposed HLW canisters. The measured data obtained since 1965 show that the thermomechanical response of the salt formation and the physical/chemical changes in the vicinity of disposal boreholes are not a serious concern and that their long-term consequences can be estimated based on theoretical considerations and in-situ investigations

Application and further development of models for the final repository safety analyses on the clearance of radioactive materials for disposal. Final report; Anwendung und Weiterentwicklung von Modellen fuer Endlagersicherheitsanalysen auf die Freigabe radioaktiver Stoffe zur Deponierung. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Artmann, Andreas; Larue, Juergen; Seher, Holger; Weiss, Dietmar

2014-08-15

The project of application and further development of models for the final repository safety analyses on the clearance of radioactive materials for disposal is aimed to study the long-term safety using repository-specific simulation programs with respect to radiation exposure for different scenarios. It was supposed to investigate whether the 10 micro Sv criterion can be guaranteed under consideration of human intrusion scenarios. The report covers the following issues: selection and identification of models and codes and the definition of boundary conditions; applicability of conventional repository models for long-term safety analyses; modeling results for the pollutant release and transport and calculation of radiation exposure; determination of the radiation exposure.

Safeguards for geological repositories

International Nuclear Information System (INIS)

Fattah, A.

2000-01-01

substantially large. Change in social, economic, environmental and other scenarios might demand recovery of nuclear and other material from the repository sometime in the future. To this end, the Department of Safeguards has developed a policy paper to guide the planner, designer and operator to incorporate safeguards related features, as appropriate. In parallel, a programme for the Development of Safeguards for Final Disposal of Spent Fuel in Geological Repositories (SAGOR) was launched to foster technological advancement. The mission of SAGOR has been to ensure that the safeguards systems developed for the final disposal of spent fuel effectively meet the objectives of IAEA safeguards, optimise IAEA resources, and make best use of existing technologies while still meeting the requirements for safety and environmental protection. (author)

National waste terminal storage repository in a bedded salt formation for spent unreprocessed fuel. Quality assurance program for licensing

International Nuclear Information System (INIS)

1978-12-01

A National Waste Terminal Storage Repository, in bedded salt, for spent unreprocessed fuel is the subject of a conceptual design project which began in January 1977. This volume presents a preliminary quality assurance program to guide the license applicant in developing a detailed program that will be compatible with anticipated National Waste Terminal Storage (NWTSR2) contracting arrangements and provide the documentation required by regulatory bodies. This QA program is designed to provide confidence that the quality-related activities pertaining to safety-related structures, systems, and components will be identified and controlled. Specific responsibilities for quality-related activities are documented and assigned to personnel and organizations for the major phases of facility design and construction. These responsibilities encompass a broad range of activities and are addressed in this preliminary program. The quality assurance program elements are organized and discussed herein as follows: (1) quality assurance during design and construction; (2) the applicant (DOE); (3) siting contractor; (4) architect/engineer; (5) project field management; and (6) operations contractor

Summary of four release consequence analyses for hypothetical nuclear waste repositories in salt and granite

International Nuclear Information System (INIS)

Cole, C.R.; Bond, F.W.

1980-12-01

Release consequence methology developed under the Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) program has now been applied to four hypothetical repository sites. This paper summarizes the results of these four studies in order to demonstrate that the far-field methodology developed under the AEGIS program offers a practical approach to the post-closure safety assessment of nuclear waste repositories sited in deep continental geologic formations. The four studies are briefly described and compared according to the following general categories: physical description of the repository (size, inventory, emplacement depth); geologic and hydrologic description of the site and the conceptual hydrologic model for the site; description of release scenario; hydrologic model implementation and results; engineered barriers and leach rate modeling; transport model implementation and results; and dose model implementation and results. These studies indicate the following: numerical modeling is a practical approach to post-closure safety assessment analysis for nuclear waste repositories; near-field modeling capability needs improvement to permit assessment of the consequences of human intrusion and pumping well scenarios; engineered barrier systems can be useful in mitigating consequences for postulated release scenarios that short-circuit the geohydrologic system; geohydrologic systems separating a repository from the natural biosphere discharge sites act to mitigate the consequences of postulated breaches in containment; and engineered barriers of types other than the containment or absorptive type may be useful

Safety studies of HLW-disposal in the Mors salt dome - Support to the salt option of the Pagis project

International Nuclear Information System (INIS)

Lindstroem Jensen, K.E.

1987-01-01

The study, which is a support to the Pagis project, covers three tasks concerning the evaluation of the Danish salt dome Mors (variant disposal site): evaluation of the human intrusion scenario where a cavern is excavated near the HLW-repository by solution mining technique. The waste is supposed to be leached during the operation period until the abandoned cavern is closed by convergence and the contaminated brine is pressed up into the overburden. Evaluation of the brine intrusion scenario, where the HLW-repository is inadvertently located close to a major brine pocket which subsequently releases its brine content through defects in the repository to the discharge stream for the catchment area. Collection and description of hydrological data of surface and deep layers (down to circa 700 metres) in the repository region. The data will be used by GSF to calculate the radionuclide migration in the geosphere

Impact of thermal constraints on the optimal design of high-level waste repositories in geologic media

Energy Technology Data Exchange (ETDEWEB)

Malbrain, C; Lester, R K [Massachusetts Inst. of Tech., Cambridge (USA). Dept. of Nuclear Engineering

1982-12-01

An approximate, semi-analytical heat conduction model for predicting the time-dependent temperature distribution in the region of a high-level waste repository has been developed. The model provides the basis for a systematic, inexpensive examination of the impact of several independent thermal design constraints on key repository design parameters and for determining the optimal set of design parameters which satisfy these constraints. Illustrative calculations have been carried out for conceptual repository designs for spent pressurized water reactor (PWR) fuel and reprocessed PWR high-level waste in salt and granite media.

Reference design description for a geologic repository. Revision 02

International Nuclear Information System (INIS)

1999-01-01

This Reference Design Description explains the current design for a potential geologic repository that may be located at Yucca Mountain in Nevada. It describes the proposed design for a surface facility, subsurface repository, and waste packaging; it also presents the current design of the key engineering systems for the final four phases: operations, monitoring, closure, and postclosure. In addition, this Reference Design Description reviews the expected long-term performance of the potential repository. In accordance with current law, this design does not include an interim storage option. This document has six major sections. Section 1 describes the physical layout of the proposed repository. The second section describes the 4-phase evolution of the development of the proposed repository. Section 3 describes the reception of waste from offsite locations. The fourth section details the various systems that will package the waste and move it below ground as well as safety monitoring and closure. Section 5 describes the systems (both physical and analytical) that ensure continued safety after closure. The final section offers design options that may be adopted to increase the margin of safety

Salt site performance assessment activities

International Nuclear Information System (INIS)

Kircher, J.F.; Gupta, S.K.

1983-01-01

During this year the first selection of the tools (codes) for performance assessments of potential salt sites have been tentatively selected and documented; the emphasis has shifted from code development to applications. During this period prior to detailed characterization of a salt site, the focus is on bounding calculations, sensitivity and with the data available. The development and application of improved methods for sensitivity and uncertainty analysis is a focus for the coming years activities and the subject of a following paper in these proceedings. Although the assessments to date are preliminary and based on admittedly scant data, the results indicate that suitable salt sites can be identified and repository subsystems designed which will meet the established criteria for protecting the health and safety of the public. 36 references, 5 figures, 2 tables

Software Hardware Asset Reuse Enterprise (SHARE) Repository Framework Final Report: Component Specification and Ontology

National Research Council Canada - National Science Library

Johnson, Jean; Blais, Curtis

2008-01-01

...) was tasked to develop a component specification and ontology for the SHARE repository. A description of SHARE and the requirements for a component specification and ontology supporting this repository are available in Johnson (2007...

Geologic nuclear waste repository site selection studies in the Paradox Basin, Utah

International Nuclear Information System (INIS)

Rogers, T.H.; Conwell, F.R.

1981-01-01

During Phase I regional-level studies, a literature review was conducted to ascertain geologic characteristics pertinent to repository siting factors. On the basis of the regional screening results, four areas in southeastern Utah were selected as being suitable for more detailed study in Phase II: Elk Ridge and Gibson Dome, containing nearly horizontal bedded salt deposits; Salt Valley, containing a diapiric salt anticline; and Lisbon Valley, containing a non-diapiric salt anticline. During current Phase II area studies, the four study areas are being characterized in greater detail than in Phase I. Phase II will culminate in the identification of a potentially suitable location(s), if any, that will be recommended for study in still greater detail in a subsequent phase of work. 5 refs

Hydrogeologic effects of natural disruptive events on nuclear waste repositories

International Nuclear Information System (INIS)

Davis, S.N.

1980-06-01

Some possible hydrogeologic effects of disruptive events that may affect repositories for nuclear waste are described. A very large number of combinations of natural events can be imagined, but only those events which are judged to be most probable are covered. Waste-induced effects are not considered. The disruptive events discussed above are placed into four geologic settings. Although the geology is not specific to given repository sites that have been considered by other agencies, the geology has been generalized from actual field data and is, therefore, considered to be physically reasonable. The geologic settings considered are: (1) interior salt domes of the Gulf Coast, (2) bedded salt of southeastern New Mexico, (3) argillaceous rocks of southern Nevanda, and (4) granitic stocks of the Basin and Range Province. Log-normal distributions of permeabilities of rock units are given for each region. Chapters are devoted to: poresity and permeability of natural materials, regional flow patterns, disruptive events (faulting, dissolution of rock forming minerals, fracturing from various causes, rapid changes of hydraulic regimen); possible hydrologic effects of disruptive events; and hydraulic fracturing

75 FR 42683 - Certain Potassium Phosphate Salts From the People's Republic of China: Amended Final...

Science.gov (United States)

2010-07-22

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-962] Certain Potassium Phosphate Salts From the People's Republic of China: Amended Final Determination of Sales at Less Than Fair Value and Antidumping Duty Order AGENCY: Import Administration, International Trade Administration...

Chemistry of transuranium elements in salt-base repository

Energy Technology Data Exchange (ETDEWEB)

Borkowski, Marian [Los Alamos National Laboratory; Reed, Donald T [Los Alamos National Laboratory; Lucchini, Jean - Francois [Los Alamos National Laboratory; Richmann, Michael K [Los Alamos National Laboratory; Khaing, H [Los Alamos National Laboratory; Swanson, J [Los Alamos National Laboratory; Ams, D [Los Alamos National Laboratory

2010-12-02

The mobility and potential release of actinides into the accessible environment continues to be the key performance assessment concern of nuclear repositories. Actinide, in particular plutonium speciation under the wide range of conditions that can exist in the subsurface is complex and depends strongly on the coupled effects of redox conditions, inorganic/organic complexation, and the extent/nature of aggregation. Understanding the key factors that define the potential for actinide migration is, in this context, an essential and critical part of making and sustaining a licensing case for a nuclear repository. Herein we report on recent progress in a concurrent modeling and experimental study to determine the speciation of plutonium, uranium and americium in high ionic strength Na-CI-Mg brines. This is being done as part of the ongomg recertification effort m the Waste Isolation Pilot Plant (WIPP). The oxidation-state specific solubility of actinides were established in brine as function of pC{sub H+}, brine composition and the presence and absence of organic chelating agents and carbonate. An oxidation-state invariant analog approach using Nd{sup 3+} and Th{sup 4+} was used for An{sup 3+} and An{sup 4+} respectively. These results show that organic ligands and hydrolysis are key factors for An(III) solubility, hydrolysis at pC{sub H+} above 8 is predominate for An(IV) and carbonates are the key factor for U(VI) solubility. The effect of high ionic strength and brine components measured in absence of carbonates leads to measurable increased in overall solubility over analogous low ionic strength groundwater. Less is known about the bioreduction of actinides by halo-tolerant microorganisms, but there is now evidence that bioreduction does occur and is analogous, in many ways, to what occurs with soil bacteria. Results of solubility studies that focus on Pitzer parameter corrections, new species (e.g. borate complexation), and the thermodynamic parameters for

Hydrological and hydrogeological effects of an open repository in Forsmark. Final MIKE SHE flow modelling results for the Environmental Impact Assessment

International Nuclear Information System (INIS)

Maartensson, Erik; Gustafsson, Lars-Goeran

2010-07-01

This report presents methodology and modelling results concerning a deep-rock repository for spent nuclear fuel in Forsmark. Specifically, the modelling tools MIKE SHE, MIKE 11 and MOUSE are used to quantify the groundwater inflow to the repository and associated hydrological and hydrogeological effects during the construction and operation phases. The modelling results presented in the report provide input to the Environmental Impact Assessment (EIA) that will be part of a permit application according to the Environmental Code. Based on an existing MIKE SHE model for Forsmark, the first step of the modelling process was to implement an updated hydrogeological model of the bedrock and to increase the vertical and horizontal extents of the model domain. Other model updates involve the vegetation classification, and implementation of SFR (final repository for short-lived radioactive waste) and the subsurface drainage system at the nearby nuclear power plant. The updated model was calibrated using measured data on groundwater levels in the Quaternary deposits and the bedrock, water levels in lakes, and stream discharges. The calibrated model was then used for simulation of undisturbed conditions (i.e. without the repository) as a reference for modelling results obtained for disturbed conditions (with the repository). The modelling results for undisturbed conditions that are presented in the report closely resemble those of the final MIKE SHE site descriptive modelling (SDM-Site Forsmark). The repository layout was implemented as pipe links (segments) in the modelling tool MOUSE, and the implemented layout was used for the modelling of disturbed conditions. The study uses an updated and verified MIKE SHE-MOUSE coupling routine that is specifically adapted for calculation of groundwater inflow to grouted rock tunnels. The vertical shafts of the repository are implemented in the form of MIKE SHE grid cells with atmospheric pressure. Modelling results for disturbed

Hydrological and hydrogeological effects of an open repository in Forsmark. Final MIKE SHE flow modelling results for the Environmental Impact Assessment

Energy Technology Data Exchange (ETDEWEB)

Maartensson, Erik; Gustafsson, Lars-Goeran (DHI Sverige AB (Sweden))

2010-07-15

This report presents methodology and modelling results concerning a deep-rock repository for spent nuclear fuel in Forsmark. Specifically, the modelling tools MIKE SHE, MIKE 11 and MOUSE are used to quantify the groundwater inflow to the repository and associated hydrological and hydrogeological effects during the construction and operation phases. The modelling results presented in the report provide input to the Environmental Impact Assessment (EIA) that will be part of a permit application according to the Environmental Code. Based on an existing MIKE SHE model for Forsmark, the first step of the modelling process was to implement an updated hydrogeological model of the bedrock and to increase the vertical and horizontal extents of the model domain. Other model updates involve the vegetation classification, and implementation of SFR (final repository for short-lived radioactive waste) and the subsurface drainage system at the nearby nuclear power plant. The updated model was calibrated using measured data on groundwater levels in the Quaternary deposits and the bedrock, water levels in lakes, and stream discharges. The calibrated model was then used for simulation of undisturbed conditions (i.e. without the repository) as a reference for modelling results obtained for disturbed conditions (with the repository). The modelling results for undisturbed conditions that are presented in the report closely resemble those of the final MIKE SHE site descriptive modelling (SDM-Site Forsmark). The repository layout was implemented as pipe links (segments) in the modelling tool MOUSE, and the implemented layout was used for the modelling of disturbed conditions. The study uses an updated and verified MIKE SHE-MOUSE coupling routine that is specifically adapted for calculation of groundwater inflow to grouted rock tunnels. The vertical shafts of the repository are implemented in the form of MIKE SHE grid cells with atmospheric pressure. Modelling results for disturbed

Development of a method for the comparison of final repository sites in different host rock formations; Weiterentwicklung einer Methode zum Vergleich von Endlagerstandorten in unterschiedlichen Wirtsgesteinsformationen

Energy Technology Data Exchange (ETDEWEB)

Fischer-Appelt, Klaus; Frieling, Gerd; Kock, Ingo; and others

2017-10-15

The report on the development of a method for the comparison of final repository sites in different host rock formations covers the following issues: influence of the requirement of retrievability on the methodology, study on the possible extension of the methodology for repository sites with crystalline host rocks: boundary conditions in Germany, final disposal concept for crystalline host rocks, generic extension of the VerSi method, identification, classification and relevance weighting of safety functions, relevance of the safety functions for the crystalline host rock formation, review of the methodological need for changes for crystalline rock sites under low-permeability covering; study on the applicability of the methodology for the determination of site regions for surface exploitation (phase 1).

Attitudes towards a final repository for the spent nuclear fuel. Structure and causes; Attityd till slutfoervar av anvaent kaernbraensle. Struktur och orsaker

Energy Technology Data Exchange (ETDEWEB)

Sjoeberg, Lennart (Stockholm School of Economics (Sweden). Center for Risk Research)

2008-09-15

This report presents the results of a questionnaire survey of attitudes towards a final repository for the spent nuclear fuel. The questionnaire was mailed to 3,000 persons. Participants were young and older people in Oskarshamn municipality and Oesthammar municipality as well as in the rest of the country. Fifty-one percent responded. The questionnaire included a large number of questions of possible relevance for understanding the structure of and reasons for the person's attitude towards a final repository. Questions concerning nuclear power were dealt with in a special section. Men were more positively disposed towards a repository than women, older people more than young. The gender differences are mainly attributable to the variation in attitude towards nuclear power and concern about nuclear accidents. In the case of older people, interest was also a factor. Young people were not as interested in the issue. The most important factor in determining the attitude towards a final repository was the benefit it was expected to bring to the municipality. Moral and emotional aspects were also important. Risk played a relatively subordinate role. Social aspects were very important: those who frequently spoke with people who were positively disposed tended to be positive themselves, and vice versa for those who were negative. This factor could explain some of the gender differences in attitude. Attitudes in Oskarshamn were slightly more positive than in Oesthammar, probably due to the fact that the residents in Oskarshamn had a greater sense of participation in the municipality's decision in the matter. Information from SKB was also found to be an important factor for the differences in attitude between the municipalities. Eight percentage points more people had received information in Oskarshamn than in Oesthammar. The difference may be small, but it exists and does appear to be of some importance. Attitudes in Oskarshamn and Oesthammar continued to be much

Geology and salt deposits of the Michigan Basin

International Nuclear Information System (INIS)

Johnson, K.S.; Gonzales, S.

1976-07-01

The Silurian-age Salina salt, one of the greatest deposits of bedded rock salt in the world, underlies most of the Michigan basin and parts of the Appalachian basin in Ohio. Pennsylvania, New York, and West Virginia. Interest in this salt deposit has increased in recent years because there may be one or more areas where it could be used safely as a repository for the underground storage of high-level radioactive wastes. The general geology of the Michigan basin is summarized and the major salt deposits are described in the hope that these data will be useful in determining whether there are any areas in the basin that are sufficiently promising to warrant further detailed study. Distribution of the important salt deposits in the basin is limited to the Southern Peninsula of Michigan

VerSi. A method for the quantitative comparison of repository systems

Energy Technology Data Exchange (ETDEWEB)

Kaempfer, T.U.; Ruebel, A.; Resele, G. [AF-Consult Switzerland Ltd, Baden (Switzerland); Moenig, J. [GRS Braunschweig (Germany)

2015-07-01

arguments. We demonstrate the capabilities of the method by comparing two rather different repository systems: (1) a repository in salt with layout and site properties corresponding to the Gorleben site according to the state of knowledge and planning of 2007; (2) a fictive repository in the Lower Cretaceous claystones at a synthetic site in northern Germany with a layout corresponding to the repository planning in Switzerland and France in the years around 2005. The exemplary application of the method shows the kind of statements which can be derived and the restrictions that are often connected to these statements. In particular, it is shown that the two repository systems exhibit fundamentally different probability-consequence profiles. The main reason for this is that, according to the model calculations, radionuclide release from the salt repository occurs only in one scenario that does not represent the expected system evolution, whereas radionuclide release from the claystone repository occurs, though mostly at very low rates, in all scenarios. Such fundamentally different probability-consequence profiles have to be taken into account when evaluating the results of the presented or any other comparison method. It must be emphasized that no conclusions on the suitability of the considered host rocks in general or the Gorleben site in particular may be drawn from the exemplary results presented here.

Potential host media for a high-level waste repository

Energy Technology Data Exchange (ETDEWEB)

Hustrulid, W

1982-01-01

Earlier studies of burial of radioactive wastes in geologic repositories had concentrated on salt formations for well-publicized reasons. However, under the Carter administration, significant changes were made in the US nuclear waste management program. Changes which were made were: (1) expansion of the number of rock types under consideration; (2) adoption of the multiple-barrier approach to waste containment; (3) additional requirements for waste retrieval; and (4) new criteria proposed by the Nuclear Regulatory Commission for the isolation of high-level waste in geologic repositories. Results of the studies of different types of rocks as repository sites are summarized herein. It is concluded that each generic rock type has certain advantages and disadvantages when considered from various aspects of the waste disposal problem and that characteristics of rocks are so varied that a most favorable or least favorable rock type cannot be easily identified. This lack of definitive characteristics of rocks makes site selection and good engineering barriers very important for containment of the wastes. (BLM)

Design aspects of the Alpha Repository. I. Preliminary results of facility layout, room stability, and equipment selection efforts. Summary progress report RSI-0024

International Nuclear Information System (INIS)

Gnirk, P.F.; Grams, W.H.; Zeller, T.J.; Ellis, D.B.; Pariseau, W.G.; Fossum, A.F.; Ratigan, J.L.; Hansen, F.D.

1975-01-01

Results of preliminary analysis of the stability of mines in salt formations underlying Eddy and Lea Counties in New Mexico are presented. Methods and equipment for drilling canister emplacement holes in these formations were evaluated along with methods for excavating storage areas and transport of the excavated salt. Progress during the period is reported in chapters on geological and rock properties at the repository site, preliminary mine layout, basic requirements for repository usage, excavation geometries, drill selection, excavation systems, and safety requirements

Investigation of modern methods of probalistic sensitivity analysis of final repository performance assessment models (MOSEL)

International Nuclear Information System (INIS)

Spiessl, Sabine; Becker, Dirk-Alexander

2017-06-01

Sensitivity analysis is a mathematical means for analysing the sensitivities of a computational model to variations of its input parameters. Thus, it is a tool for managing parameter uncertainties. It is often performed probabilistically as global sensitivity analysis, running the model a large number of times with different parameter value combinations. Going along with the increase of computer capabilities, global sensitivity analysis has been a field of mathematical research for some decades. In the field of final repository modelling, probabilistic analysis is regarded a key element of a modern safety case. An appropriate uncertainty and sensitivity analysis can help identify parameters that need further dedicated research to reduce the overall uncertainty, generally leads to better system understanding and can thus contribute to building confidence in the models. The purpose of the project described here was to systematically investigate different numerical and graphical techniques of sensitivity analysis with typical repository models, which produce a distinctly right-skewed and tailed output distribution and can exhibit a highly nonlinear, non-monotonic or even non-continuous behaviour. For the investigations presented here, three test models were defined that describe generic, but typical repository systems. A number of numerical and graphical sensitivity analysis methods were selected for investigation and, in part, modified or adapted. Different sampling methods were applied to produce various parameter samples of different sizes and many individual runs with the test models were performed. The results were evaluated with the different methods of sensitivity analysis. On this basis the methods were compared and assessed. This report gives an overview of the background and the applied methods. The results obtained for three typical test models are presented and explained; conclusions in view of practical applications are drawn. At the end, a recommendation

Investigation of modern methods of probalistic sensitivity analysis of final repository performance assessment models (MOSEL)

Energy Technology Data Exchange (ETDEWEB)

Spiessl, Sabine; Becker, Dirk-Alexander

2017-06-15

Sensitivity analysis is a mathematical means for analysing the sensitivities of a computational model to variations of its input parameters. Thus, it is a tool for managing parameter uncertainties. It is often performed probabilistically as global sensitivity analysis, running the model a large number of times with different parameter value combinations. Going along with the increase of computer capabilities, global sensitivity analysis has been a field of mathematical research for some decades. In the field of final repository modelling, probabilistic analysis is regarded a key element of a modern safety case. An appropriate uncertainty and sensitivity analysis can help identify parameters that need further dedicated research to reduce the overall uncertainty, generally leads to better system understanding and can thus contribute to building confidence in the models. The purpose of the project described here was to systematically investigate different numerical and graphical techniques of sensitivity analysis with typical repository models, which produce a distinctly right-skewed and tailed output distribution and can exhibit a highly nonlinear, non-monotonic or even non-continuous behaviour. For the investigations presented here, three test models were defined that describe generic, but typical repository systems. A number of numerical and graphical sensitivity analysis methods were selected for investigation and, in part, modified or adapted. Different sampling methods were applied to produce various parameter samples of different sizes and many individual runs with the test models were performed. The results were evaluated with the different methods of sensitivity analysis. On this basis the methods were compared and assessed. This report gives an overview of the background and the applied methods. The results obtained for three typical test models are presented and explained; conclusions in view of practical applications are drawn. At the end, a recommendation

Earthquakes - a danger to deep-lying repositories?

International Nuclear Information System (INIS)

2012-03-01

This booklet issued by the Swiss National Cooperative for the Disposal of Radioactive Waste NAGRA takes a look at geological factors concerning earthquakes and the safety of deep-lying repositories for nuclear waste. The geological processes involved in the occurrence of earthquakes are briefly looked at and the definitions for magnitude and intensity of earthquakes are discussed. Examples of damage caused by earthquakes are given. The earthquake situation in Switzerland is looked at and the effects of earthquakes on sub-surface structures and deep-lying repositories are discussed. Finally, the ideas proposed for deep-lying geological repositories for nuclear wastes are discussed

Testing of high-level waste forms under repository conditions

International Nuclear Information System (INIS)

Mc Menamin, T.

1989-01-01

The workshop on testing of high-level waste forms under repository conditions was held on 17 to 21 October 1988 in Cadarache, France, and sponsored by the Commission of the European Communities (CEC), the Commissariat a l'energie atomique (CEA) and the Savannah River Laboratory (US DOE). Participants included representatives from Australia, Belgium, Denmark, France, Germany, Italy, Japan, the Netherlands, Sweden, Switzerland, The United Kingdom and the United States. The first part of the conference featured a workshop on in situ testing of simulated nuclear waste forms and proposed package components, with an emphasis on the materials interface interactions tests (MIIT). MIIT is a sevent-part programme that involves field testing of 15 glass and waste form systems supplied by seven countries, along with potential canister and overpack materials as well as geologic samples, in the salt geology at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, USA. This effort is still in progress and these proceedings document studies and findings obtained thus far. The second part of the meeting emphasized multinational experimental studies and results derived from repository systems simulation tests (RSST), which were performed in granite, clay and salt environments

Overview of ONWI'S Salt site selection program

International Nuclear Information System (INIS)

Madia, W.J.

1983-01-01

In the past year, activities in the salt site selection program of the Office of Nuclear Waste Isolation (ONWI) have focused on narrowing the number and size of areas under consideration as candidate repository sites. The progressive focusing is illustrated. Bedded salt, in the Permian Basin of West Texas and the Paradox Basin of Utah, and salt domes in the Gulf Coast Salt Dome Region (including parts of East Texas, Louisiana, and Mississippi) have been the subjects of geologic, environmental, and socioeconomic characterization of progressively greater detail as the screening process has proceeded. Detailed, field-oriented research and testing have superceded broad-based studies relying heavily on literature and other existing data. Coinciding with the increased field activities has been the publication of results and recommendations resulting from earlier program efforts

Radiolysis salt phenomenology: application to storage of high level radioactive waste

International Nuclear Information System (INIS)

Akram, Najib

1993-01-01

In France, rock salt is a candidate repository for highly radioactive waste. Rock salt contains water and adsorbed gases which can be released in boreholes after heating due to vitrified wastes. In addition, waste-induced irradiation in near-field conditions induce radiolytic reactions which also contribute to gas release. The aim of this work is to understand and evaluate the effects of heat and irradiation produced by waste containers in a deep disposal, primarily concerning gas production. This is justified by the impact of gases on long-term safety: toxicity, explosibility, chemical reactivity, pressure build-up. We have evidenced the influence of integrated dose, filling gases, temperature and grain size on an homogeneous medium (Asse Mine rock salt). We have then studied heterogeneous samples, which allowed to determine the influence of the chemical and mineralogical composition of rock salt (bedded rock salt from the Mine de Potasse d'Alsace). The role played by organic matter on gas production is important, leading for instance to high consumption rates of oxygen. Through this study, we have also considered the behaviour of clay-rich materials under irradiation. Our results constitute important bases for the future modelling of the phenomena which will take place in the near-field of a rock salt-type repository, especially concerning its long-term safety. (author) [fr

NPP Krsko: LILW Repository or Long Term Storage

International Nuclear Information System (INIS)

Lokner, V.; Subasic, D.; Levanat, I.

2008-01-01

Construction of the facilities for LILW and SF management, as planned in Decommissioning and LILW and SF management program for NPP Krsko, would be a rather expensive and challenging project for such a small nuclear program. In order to accommodate waste arising from a single nuclear power plant, one LILW repository should be constructed before the end of the NPP operation, then one SF dry storage, and finally one geological repository. This requires relatively urgent identification within Slovenian/Croatian territory of three locations that meet the criteria for establishment of such facilities and are acceptable to the local communities. There are very few such potential locations. The siting process for the first of the three facilities is well under way in Slovenia, because the country wants to have its LILW repository in operation by the year 2013. In order to facilitate public acceptance, Slovenian government has introduced financial incentives to local communities for the repository construction and operation. These 'compensations for limited land use' may significantly increase the overall costs of disposal if the repository is in operation for a long period. In the recent years, however, a possibility of long term storage (LTS) is gaining an increased attention in the waste management community, and has already been introduced e.g. in the Netherlands. It is a particularly viable option for limited waste quantities. Disposal remains the final solution, but present technologies have made possible a relatively inexpensive storage up to about hundred years, which can accommodate LILW, HLW and SF from nuclear programs as well as research reactor waste and NORM. Such storage would be a safe and simple temporary solution, encompassing all immediate and near future waste management needs. In addition, it would increase flexibility and reduce financing requirements for the final waste disposal: providing additional time for reduction of radiation emission and heat

Geologic environments for nuclear waste repositories

Directory of Open Access Journals (Sweden)

Paleologos Evan K.

2017-01-01

Full Text Available High-level radioactive waste (HLW results from spent reactor fuel and reprocessed nuclear material. Since 1957 the scientific consensus is that deep geologic disposal constitutes the safest means for isolating HLW for long timescales. Nuclear power is becoming significant for the Arab Gulf countries as a way to diversify energy sources and drive economic developments. Hence, it is of interest to the UAE to examine the geologic environments currently considered internationally to guide site selection. Sweden and Finland are proceeding with deep underground repositories mined in bedrock at depths of 500m, and 400m, respectively. Equally, Canada’s proposals are deep burial in the plutonic rock masses of the Canadian Shield. Denmark and Switzerland are considering disposal of their relative small quantities of HLW into crystalline basement rocks through boreholes at depths of 5,000m. In USA, the potential repository at Yucca Mountain, Nevada lies at a depth of 300m in unsaturated layers of welded volcanic tuffs. Disposal of low and intermediate-level radioactive wastes, as well as the German HLW repository favour structurally-sound layered salt stata and domes. Our article provides a comprehensive review of the current concepts regarding HLW disposal together with some preliminary analysis of potentially appropriate geologic environments in the UAE.

Final storage of radioactive waste in Germany. Are administrative structures in need of modification?

International Nuclear Information System (INIS)

Schneider, Horst

2011-01-01

Delays in commissioning the Konrad Mine as a repository for radioactive waste not generating heat, and in exploring the Gorleben salt dome for suitability as a repository for high-level waste generating heat, invite the question whether the legal regulations in place, especially administration and funding of the repository, are suitable for solving current problems or whether they are in need of improvement. The key principles of the back end of the nuclear fuel cycle, final storage included, were laid down as rules in 1976. Execution of the necessary waste management steps, from radioactive waste arisings to their final disposal, was split between private responsibilities and government competences. Final storage, to this day, has been of prime importance. Pursuant to the Atomic Energy Act, the federal government is required to set up facilities for final storage of radioactive waste. The waste management duties incumbent upon private parties, from radioactive waste arisings to delivery, are mainly subject to safety criteria under the Atomic Energy Act and the Radiation Protection Ordinance. As far as administration is concerned, the private parties are free in the way they comply with regulatory requirements. They are required to bear the cost in accordance with the polluter-pays-principle. In the light of the sluggish execution of government tasks from 1976 to this day, the question of improvements has become more acute than ever. This is where assignment offers an approach towards better administration which can be taken at short notice, as assignment implies a reduction in the number of interfaces and clearer responsibilities. However, even the best administration is unable to lead to the repositories required by law if those responsible in government fail to act in accordance with the spirit and letter of the law. (orig.)

Third report, development of site suitability and design performance data base for a high level nuclear waste repository

International Nuclear Information System (INIS)

1978-05-01

This report presents the results of mining and geotechnical studies provided as support for the development of a technical data base suitable for the generation of a regulatory framework governing high-level nuclear waste disposal: flow path models for basalts, salt domes, and crystalline rocks; simplistic model evaluations; loss of administrative control; repository conceptual designs; repository design considerations; and design performance criteria

The procedure of alternative site selection within the report of the study group on the radioactive waste final repository selection process (AKEnd)

International Nuclear Information System (INIS)

Nies, A.

2005-01-01

The study group on the selection procedures of radioactive waste final repository sites has presented the report in December 2002. The author dicusses the consequences of this report with respect to the site selection focussing on two topics: the serach for the best possible site and the prevention of prejudices

Scientific basis for a safety case of deep geological repositories

Energy Technology Data Exchange (ETDEWEB)

Noseck, Ulrich; Becker, Dirk-Alexander; Brasser, Thomas [and others

2012-11-15

: - The current state-of-the-art in long-term safety assessment has been evaluated within a sub project of the Integration Group for the safety case (IGSC) of OECD/NEA. GRS has strongly contributed to this project called Methods for Safety Assessments (MeSA), by leading working groups and with contributions to selected chapters of the NEA state-of-the-art report. - As an outcome of the MeSA project it was decided to compile the status in the OECD member countries on the use of indicators complementary to dose and risk in the safety case. GRS played a leading role in drafting and finalizing a state-of-the-art report on indicators. Further the applicability of a specific set of indicators previously proposed in Germany was tested and evaluated for repositories in clay and rock salt formations. - GRS is involved in several international working groups to follow the state-of-the-art at the international level as well as to introduce results from German R and D into the international discussion. Important working groups are the Radioactive Waste Management Committee (RWMC) of OECD/NEA with the Integration Group for the Safety Case, its subgroups Clay Club and Salt Club and correlated projects like the NEA sorption project. - The current literature dealing with the role of microbial processes related to repositories in clay formations has been compiled. The potential negative and positive impact of microbes on the long-term integrity of the repository system in clay has been qualitatively evaluated. - Radionuclide inventories of CSD-V containers received from reprocessing in LA Hague have been evaluated and an updated data set for long-term safety assessment is proposed. - The non-isothermal re-saturation of bentonite is investigated by specific laboratory experiments accompanied by modelling with the code VIPER. In addition the model was applied to lab and field experiments provided by the EBS task force and all results have been discussed in this international working group

Scientific basis for a safety case of deep geological repositories

International Nuclear Information System (INIS)

Noseck, Ulrich; Becker, Dirk-Alexander; Brasser, Thomas

2012-11-01

: - The current state-of-the-art in long-term safety assessment has been evaluated within a sub project of the Integration Group for the safety case (IGSC) of OECD/NEA. GRS has strongly contributed to this project called Methods for Safety Assessments (MeSA), by leading working groups and with contributions to selected chapters of the NEA state-of-the-art report. - As an outcome of the MeSA project it was decided to compile the status in the OECD member countries on the use of indicators complementary to dose and risk in the safety case. GRS played a leading role in drafting and finalizing a state-of-the-art report on indicators. Further the applicability of a specific set of indicators previously proposed in Germany was tested and evaluated for repositories in clay and rock salt formations. - GRS is involved in several international working groups to follow the state-of-the-art at the international level as well as to introduce results from German R and D into the international discussion. Important working groups are the Radioactive Waste Management Committee (RWMC) of OECD/NEA with the Integration Group for the Safety Case, its subgroups Clay Club and Salt Club and correlated projects like the NEA sorption project. - The current literature dealing with the role of microbial processes related to repositories in clay formations has been compiled. The potential negative and positive impact of microbes on the long-term integrity of the repository system in clay has been qualitatively evaluated. - Radionuclide inventories of CSD-V containers received from reprocessing in LA Hague have been evaluated and an updated data set for long-term safety assessment is proposed. - The non-isothermal re-saturation of bentonite is investigated by specific laboratory experiments accompanied by modelling with the code VIPER. In addition the model was applied to lab and field experiments provided by the EBS task force and all results have been discussed in this international working group

Heat transfer studies in salt and granite

International Nuclear Information System (INIS)

Just, R.A.

1978-10-01

Results are presented of a scoping study on the feasibility of using a multi-layer terminal repository design in both salt and granite formations to store either high-level waste or spent fuel. Calculations have been made to determine temperature profiles within the repository and to provide an estimate of the thermal uplift that can be expected. Near-field models developed to compare temperature profiles in the regions close to the waste canisters indicated that maximum thermal gradients and maximum temperature increases could be significantly reduced by changing from a single to a multi-layer repository design. For both high-level waste and for spent fuel, the maximum temperature increase in the multi-level repositories was reduced to approximately 60 percent of the temperature increase predicted for the single-level repositories at the same areal loading. After the near-field models had verified that maximum thermal gradients and temperature increases could be reduced by using a multilevel repository design, a series of far-field models was developed. The far-field models used to provide qualitative comparisons of the maximum thermal uplift indicate that the thermal uplift is roughly proportional to the energy supplied to the formation. Changing from a single- to a multi-layer repository but keeping the areal loading constant results in increased thermal uplifts

Probabilistic safety assessment for a generic deep geological repository for high-level waste and long-lived intermediate-level waste in clay

International Nuclear Information System (INIS)

Resele, G.; Holocher, J.; Mayer, G.; Hubschwerlen, N.; Niemeyer, M.; Beushausen, M.; Wollrath, J.

2010-01-01

Document available in extended abstract form only. In the selection procedure for the search of a final site location for the disposal of radioactive wastes, the comparison and evaluation of different potentially suitable repository systems in different types of host rocks will be an essential and crucial step. Since internationally accepted guidelines on how to perform such quantitative comparisons between repository systems with regard to their long-term safety behaviour are still lacking, in 2007 the German Federal Office for Radiation Protection launched the project 'VerSi' (Vergleichende Sicherheitsanalysen - Comparing Safety Assessments) that aims at the development of a methodology for the comparison of long-term safety assessments. A vital part of the VerSi project is the performance of long-term safety assessments for the comparison of two repository systems. The comparison focuses on a future repository for heat-generating, i.e. high-level and long-lived intermediate-level radioactive wastes in Germany. Rock salt is considered as a potential host rock for such a repository, and one repository system in VerSi is defined similarly to the potential site located in the Gorleben salt dome. Another suitable host rock formation may be clay. A generic location within the lower Cretaceous clays in Northern Germany is therefore chosen for the comparison of safety assessments within the VerSi project. The long-term safety assessment of a repository system for heat-generating radioactive waste at the generic clay location comprises different steps, amongst others: - Identifying the relevant processes in the near-field, in the geosphere and in the biosphere which are relevant for the long-term safety behaviour. - Development of a safety concept for the repository system. - Deduction of scenarios of the long-term evolution of the repository system. - Definition of statistic weights, i. e. the likelihood of occurrence of the scenarios. - Performance of a

Radioactive waste isolation in salt: geochemistry of brine in rock salt in temperature gradients and gamma-radiation fields - a selective annotated bibliography

International Nuclear Information System (INIS)

Hull, A.B.; Williams, L.B.

1985-07-01

Evaluation of the extensive research concerning brine geochemistry and transport is critically important to successful exploitation of a salt formation for isolating high-level radioactive waste. This annotated bibliography has been compiled from documents considered to provide classic background material on the interactions between brine and rock salt, as well as the most important results from more recent research. Each summary elucidates the information or data most pertinent to situations encountered in siting, constructing, and operating a mined repository in salt for high-level radioactive waste. The research topics covered include the basic geology, depositional environment, mineralogy, and structure of evaporite and domal salts, as well as fluid inclusions, brine chemistry, thermal and gamma-radiation effects, radionuclide migration, and thermodynamic properties of salts and brines. 4 figs., 6 tabs

Radioactive waste isolation in salt: geochemistry of brine in rock salt in temperature gradients and gamma-radiation fields - a selective annotated bibliography

Energy Technology Data Exchange (ETDEWEB)

Hull, A.B.; Williams, L.B.

1985-07-01

Evaluation of the extensive research concerning brine geochemistry and transport is critically important to successful exploitation of a salt formation for isolating high-level radioactive waste. This annotated bibliography has been compiled from documents considered to provide classic background material on the interactions between brine and rock salt, as well as the most important results from more recent research. Each summary elucidates the information or data most pertinent to situations encountered in siting, constructing, and operating a mined repository in salt for high-level radioactive waste. The research topics covered include the basic geology, depositional environment, mineralogy, and structure of evaporite and domal salts, as well as fluid inclusions, brine chemistry, thermal and gamma-radiation effects, radionuclide migration, and thermodynamic properties of salts and brines. 4 figs., 6 tabs.

Radioactive waste isolation in salt: peer review of the Office of Nuclear Waste Isolation's reports on preferred repository sites within the Palo Duro Basin, Texas

International Nuclear Information System (INIS)

Fenster, D.; Edgar, D.; Gonzales, S.; Domenico, P.; Harrison, W.; Engelder, T.; Tisue, M.

1984-04-01

Documents are being submitted to the Salt Repository Project Office (SRPO) of the US Department of Energy (DOE) by Battelle Memorial Institute's Office of Nuclear Waste Isolation (ONWI) to satisfy milestones of the Salt Repository Project of the Civilian Radioactive Waste Management Program. Some of these documents are being reviewed by multidisciplinary groups of peers to ensure DOE of their adequacy and credibility. Adequacy of documents refers to their ability to meet the standards of the US Nuclear Regulatory Commission, as enunciated in 10 CFR 60, and the requirements of the National Environmental Policy Act and the Nuclear Waste Policy Act of 1982. Credibility of documents refers to the validity of the assumptions, methods, and conclusions, as well as to the completeness of coverage. This report summarizes Argonne's review of ONWI's two-volume draft report entitled Identification of Preferred Sites within the Palo Duro Basin: Vol. 1 - Palo Duro Location A, and Vol. 2 - Palo Duro Location B, dated January 1984. Argonne was requested by DOE to review these documents on January 17 and 24, 1984 (see App. A). The review procedure involved obtaining written comments on the reports from three members of Argonne's core peer review staff and three extramural experts in related research areas. The peer review panel met at Argonne on February 6, 1984, and reviewer comments were integrated into this report by the review session chairman, with the assistance of Argonne's core peer review staff. All of the peer review panelists concurred in the way in which their comments were represented in this report (see App. B). A letter report and a draft of this report were sent to SRPO on February 10, 1984, and April 17, 1984, respectively. 5 references

Precipitates/Salts Model Sensitivity Calculation

International Nuclear Information System (INIS)

Mariner, P.

2001-01-01

The objective and scope of this calculation is to assist Performance Assessment Operations and the Engineered Barrier System (EBS) Department in modeling the geochemical effects of evaporation on potential seepage waters within a potential repository drift. This work is developed and documented using procedure AP-3.12Q, ''Calculations'', in support of ''Technical Work Plan For Engineered Barrier System Department Modeling and Testing FY 02 Work Activities'' (BSC 2001a). The specific objective of this calculation is to examine the sensitivity and uncertainties of the Precipitates/Salts model. The Precipitates/Salts model is documented in an Analysis/Model Report (AMR), ''In-Drift Precipitates/Salts Analysis'' (BSC 2001b). The calculation in the current document examines the effects of starting water composition, mineral suppressions, and the fugacity of carbon dioxide (CO 2 ) on the chemical evolution of water in the drift

Further development of public participation in the site-selection and approval process of a final repository in Germany

Energy Technology Data Exchange (ETDEWEB)

Barth, Regine; Kallenbach-Herbert, Beate [OeEo-Institute e.V., Inst. for Applied Ecology, Darmstadt (Germany); Arens, Georg [Federal Office for Radiation Protection (BfS), Salzgitter (Germany)

2006-09-15

This paper reflects the first findings of a current research project funded by the German Federal Office for Radiation Protection and conducted by an interdisciplinary working group of the OEko-Institute. One focus of this project is the systematic analysis of past and existing participatory processes in different nuclear and non-nuclear projects. On the basis of this analysis and a literature review a specific concept for public participation in the site-selection and approval process of a repository for high radioactive waste (HAW repository) in Germany will be derived. The concept shall foster transparency and acceptance. The working group of the OEko-Institute combines long standing research experience and an intimate knowledge of radioactive waste management including political, technical, management and social problems of final disposal on the one hand. On the other hand members play an active role in stakeholder processes of different non-nuclear projects as well as experience with a wide range of participative measures and their impact. This allows an approach which integrates the specific features of radioactive waste disposal with a wider perspective on the demands and opportunities of stakeholder processes. The procedure of site selection for a HAW repository in Germany still has to be specified. The procedure introduced by the 'Committee on a Site Selection Procedure for Repository Sites' (Arbeitskreis Auswahlverfahren Endlagerstandorte - AkEnd) has not been adopted. The Committee had suggested installing a negotiation group to discuss the AkEnd proposals in the so called 'Phase II'. This suggestion could not be followed because not all relevant stakeholders were willing to participate. An internal draft for a federal law implementing main elements of the AkEnd findings was developed by the Ministry for Environment in 2005, but has never been brought to the cabinet. Due to the change of Government in Germany, the next steps still are

Further development of public participation in the site-selection and approval process of a final repository in Germany

International Nuclear Information System (INIS)

Barth, Regine; Kallenbach-Herbert, Beate; Arens, Georg

2006-01-01

This paper reflects the first findings of a current research project funded by the German Federal Office for Radiation Protection and conducted by an interdisciplinary working group of the OEko-Institute. One focus of this project is the systematic analysis of past and existing participatory processes in different nuclear and non-nuclear projects. On the basis of this analysis and a literature review a specific concept for public participation in the site-selection and approval process of a repository for high radioactive waste (HAW repository) in Germany will be derived. The concept shall foster transparency and acceptance. The working group of the OEko-Institute combines long standing research experience and an intimate knowledge of radioactive waste management including political, technical, management and social problems of final disposal on the one hand. On the other hand members play an active role in stakeholder processes of different non-nuclear projects as well as experience with a wide range of participative measures and their impact. This allows an approach which integrates the specific features of radioactive waste disposal with a wider perspective on the demands and opportunities of stakeholder processes. The procedure of site selection for a HAW repository in Germany still has to be specified. The procedure introduced by the 'Committee on a Site Selection Procedure for Repository Sites' (Arbeitskreis Auswahlverfahren Endlagerstandorte - AkEnd) has not been adopted. The Committee had suggested installing a negotiation group to discuss the AkEnd proposals in the so called 'Phase II'. This suggestion could not be followed because not all relevant stakeholders were willing to participate. An internal draft for a federal law implementing main elements of the AkEnd findings was developed by the Ministry for Environment in 2005, but has never been brought to the cabinet. Due to the change of Government in Germany, the next steps still are under consideration

Analysis of water content in salt deposits: its application to radioactive waste storage

International Nuclear Information System (INIS)

Cuevas Muller, C. de la.

1993-01-01

The salt deposits as radioactive storage medium are analyzed. This report studies the physical-chemical characteristics of water into salts deposits, its implications for the safety of the repository, and the transport water release mechanism. The last part analyzes the geochemical numerical data of correlation analysis, geostatistics analysis and interpretation of statistical data

Search for a final repository site. How is the status of the preparation of final radioactive waste disposal in Germany?; Endlagersuche. Wie steht es um die Vorbereitung der Entsorgung radioaktiver Abfaelle in Deutschland?

Energy Technology Data Exchange (ETDEWEB)

Mueller, Monika C.M. (ed.) [Evangelische Akademie Loccum, Rehburg-Loccum (Germany). Arbeitsbereich Naturwissenschaften, Oekologie und Umweltpolitik

2017-07-01

During the workshop on the status of the preparation of final radioactive waste disposal in Germany the following issues were discussed: socio-economic challenges two years after the final report of the commission for final disposal of radioactive wastes; the question of public participation - the difficult search for a repository site, experiences and intents of public participation during the work of the commission, interim storage of hear generating radioactive wastes, extended interim-storage, long-term interim storage facilities - opinion of the concerned public, how to establish a controlling and correcting surveillance of the process?.

Performance Prediction for Large-Scale Nuclear Waste Repositories: Final Report

International Nuclear Information System (INIS)

Glassley, W E; Nitao, J J; Grant, W; Boulos, T N; Gokoffski, M O; Johnson, J W; Kercher, J R; Levatin, J A; Steefel, C I

2001-01-01

embodied in the code accurately represents the state-of-the-art in modeling these processes, and that the conceptualization of the models used in the simulations honors the primary processes that are controlling these systems. Application of the code to a wide range of important and strategic problems has been undertaken. Particularly significant are results obtained concerning the evolution of a potential high level nuclear waste repository at Yucca Mountain, Nevada. In these simulations, the results suggest that fluid movement and chemical changes will be such as to encourage solute transport around the sides of the waste emplacement tunnels, thus minimizing the potential for seepage of water and dissolved salts into the tunnels. The results also indicate that the short term response of the geological system to waste emplacement will be complex and rapid, and will be most readily detected below waste emplacement tunnels. A successful monitoring program of repository performance during the early stages of the operational period would thus benefit by coordinating design and execution of sampling strategies with a simulation tool such as NUFT-C. Such an approach would allow efficient and cost-effective sampling strategies, and would facilitate interpretation of what will surely be complex and massive data sets

Effects of resource activities upon repository siting and waste containment with reference to bedded salt

International Nuclear Information System (INIS)

Ashby, J.; Rowe, J.

1980-02-01

The primary consideration for the suitability of a nuclear waste repository site is the overall ability of the repository to safely contain radioactive waste. This report is a discussion of the past, present, and future effects of resource activities on waste containment. Past and present resource activities which provide release pathways (i.e., leaky boreholes, adjacent mines) will receive initial evaluation during the early stages of any repository site study. However, other resource activities which may have subtle effects on containment (e.g., long-term pumping causing increased groundwater gradients, invasion of saline water causing lower retardation) and all potential future resource activities must also be considered during the site evaluation process. Resource activities will affect both the siting and the designing of repositories. Ideally, sites should be located in areas of low resource activity and low potential for future activity, and repository design should seek to eliminate or minimize the adverse effects of any resource activity. Buffer zones should be created to provide areas in which resource activities that might adversely affect containment can be restricted or curtailed. This could mean removing large areas of land from resource development. The impact of these frozen assets should be assessed in terms of their economic value and of their effect upon resource reserves. This step could require a major effort in data acquisition and analysis followed by extensive numerical modeling of regional fluid flow and mass transport. Numerical models should be used to assess the effects of resource activity upon containment and should include the cumulative effects of different resource activities. Analysis by other methods is probably not possible except for relatively simple cases

Engineering Review Group (ERG) and Geologic Review Group (GRG) report on brine migration at the Deaf Smith County site salt repository horizon

International Nuclear Information System (INIS)

1986-01-01

In April 1986, ONWI requested the ERG and GRG to jointly address the status of current knowledge of, and ONWI approach to further characterization of, the geohydrology of the candidate repository horizon of the potential site in Deaf Smith County, Texas. Specifically, the ERG-GRG was asked to evaluate the status of understanding of the hydrogeology of the Lower San Andres Unit 4 (LSA-4) evaporite section and identify any major gaps in the data; evaluate the current understanding of the chemistry and movement of brines in the LSA-4 salt and associated interbeds; develop recommendations for estimating the upper limit quantity of brines, and modeling the brine movement, with respect to the emplaced HLW packages; and identify questions concerning the chemistry of the brines and recommend a technical approach to addressing these questions. 19 refs

Influence of the design temperature on long-term safety of a salt dome repository

International Nuclear Information System (INIS)

Buhmann, D.; Brenner, J.; Storck, R.

1993-03-01

All studies made so far within the framwork of the mixed concept system analysis proceeded from a design temperature of the mine structure of 200 C. The concept based on a design temperature of 150 C was aimed at studying whether it made sense to maintain lower temperatures, if necessary. Deterministic and probabilistic calculations were made in order to determine the influence of the lower design temperature on long-term safety. The calculations were based on concept A of Joint Borehole and Gallery Storage. Assuming reference values of the input parameters, the deterministic calculations do not produce any radionuclide release from the mine structure. If, however, one assumes a lower rate for rock convergence, radionuclides are released at maximum dose rates of about 3.10 -5 Sv/a. Even a larger volume of limited brine inclusions may lead to radionuclide releases, in that case with dose commitments of the order of magnitude of 1.10 -5 Sv/a. The probabilistic calculations show that a design temperature of 150 C for long-term safety is less favourable than a higher design temperature. The share of simulations in the probabilistic calculations with a radionuclide release, and the expected value of dose commitment, are almost double as high as in the concept based on 200 C design temperature. Thus a higher design temperature is preferable with regard to the long-term safety of a salt repository. The most important parameters concerning dose commitment are the volume of limited brine inclusions, the convergence rate, and the permeability of barriers and backfilling rock. (orig./HP) [de

Options Assessment Report: Treatment of Nitrate Salt Waste at Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Robinson, Bruce Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stevens, Patrice Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-12-17

This report documents the methodology used to select a method of treatment for the remediated nitrate salt (RNS) and unremediated nitrate salt (UNS) waste containers at Los Alamos National Laboratory (LANL). The method selected should treat the containerized waste in a manner that renders the waste safe and suitable for transport and final disposal in the Waste Isolation Pilot Plant (WIPP) repository, under specifications listed in the WIPP Waste Acceptance Criteria (DOE/CBFO, 2013). LANL recognizes that the results must be thoroughly vetted with the New Mexico Environment Department (NMED) and that a modification to the LANL Hazardous Waste Facility Permit is a necessary step before implementation of this or any treatment option. Likewise, facility readiness and safety basis approvals must be received from the Department of Energy (DOE). This report presents LANL’s preferred option, and the documentation of the process for reaching the recommended treatment option for RNS and UNS waste, and is presented for consideration by NMED and DOE.

Options assessment report: Treatment of nitrate salt waste at Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Robinson, Bruce Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stevens, Patrice Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-09-16

This report documents the methodology used to select a method of treatment for the remediated nitrate salt (RNS) and unremediated nitrate salt (UNS) waste containers at Los Alamos National Laboratory (LANL). The method selected should treat the containerized waste in a manner that renders the waste safe and suitable for transport and final disposal in the Waste Isolation Pilot Plant (WIPP) repository, under specifications listed in the WIPP Waste Acceptance Criteria (DOE/CBFO, 2013). LANL recognized that the results must be thoroughly vetted with the New Mexico Environment Department (NMED) and the a modification to the LANL Hazardous Waste Facility Permit is a necessary step before implementation of this or any treatment option. Likewise, facility readiness and safety basis approvals must be received from the Department of Energy (DOE). This report presents LANL's preferred option, and the documentation of the process for reaching the recommended treatment option for RNS and UNS waste, and is presented for consideration by NMED and DOE.