Sample records for safety system surpass

  1. Development and validation of the SURgical PAtient Safety System (SURPASS) checklist

    NARCIS (Netherlands)

    de Vries, E.N.; Hollmann, M.W.; Smorenburg, S.M.; Gouma, D.J.; Boermeester, M.A.


    Introduction: A large number of preventable adverse events are encountered during hospital admission and in particular around surgical procedures. Checklists may well be effective in surgery to prevent errors and adverse events. We developed, validated and evaluated a SURgical PAtient Safety System

  2. Surpassing Shanghai: An Agenda for American Education Built on the World's Leading Systems (United States)

    Tucker, Marc S., Ed.


    This book answers a simple question: How would one redesign the American education system if the aim was to take advantage of everything that has been learned by countries with the world's best education systems? With a growing number of countries outperforming the United States on the most respected comparisons of student achievement--and…

  3. Surpassing the current limitations of biohydrogen production systems: The case for a novel hybrid approach. (United States)

    Boboescu, Iulian Zoltan; Gherman, Vasile Daniel; Lakatos, Gergely; Pap, Bernadett; Bíró, Tibor; Maróti, Gergely


    The steadily increase of global energy requirements has brought about a general agreement on the need for novel renewable and environmentally friendly energy sources and carriers. Among the alternatives to a fossil fuel-based economy, hydrogen gas is considered a game-changer. Certain methods of hydrogen production can utilize various low-priced industrial and agricultural wastes as substrate, thus coupling organic waste treatment with renewable energy generation. Among these approaches, different biological strategies have been investigated and successfully implemented in laboratory-scale systems. Although promising, several key aspects need further investigation in order to push these technologies towards large-scale industrial implementation. Some of the major scientific and technical bottlenecks will be discussed, along with possible solutions, including a thorough exploration of novel research combining microbial dark fermentation and algal photoheterotrophic degradation systems, integrated with wastewater treatment and metabolic by-products usage. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. System safety education focused on flight safety (United States)

    Holt, E.


    The measures necessary for achieving higher levels of system safety are analyzed with an eye toward maintaining the combat capability of the Air Force. Several education courses were provided for personnel involved in safety management. Data include: (1) Flight Safety Officer Course, (2) Advanced Safety Program Management, (3) Fundamentals of System Safety, and (4) Quantitative Methods of Safety Analysis.

  5. Safety system status monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, J.R.; Morgenstern, M.H.; Rideout, T.H.; Cowley, P.J.


    The Pacific Northwest Laboratory has studied the safety aspects of monitoring the preoperational status of safety systems in nuclear power plants. The goals of the study were to assess for the NRC the effectiveness of current monitoring systems and procedures, to develop near-term guidelines for reducing human errors associated with monitoring safety system status, and to recommend a regulatory position on this issue. A review of safety system status monitoring practices indicated that current systems and procedures do not adequately aid control room operators in monitoring safety system status. This is true even of some systems and procedures installed to meet existing regulatory guidelines (Regulatory Guide 1.47). In consequence, this report suggests acceptance criteria for meeting the functional requirements of an adequate system for monitoring safety system status. Also suggested are near-term guidelines that could reduce the likelihood of human errors in specific, high-priority status monitoring tasks. It is recommended that (1) Regulatory Guide 1.47 be revised to address these acceptance criteria, and (2) the revised Regulatory Guide 1.47 be applied to all plants, including those built since the issuance of the original Regulatory Guide.

  6. Software system safety (United States)

    Uber, James G.


    Software itself is not hazardous, but since software and hardware share common interfaces there is an opportunity for software to create hazards. Further, these software systems are complex, and proven methods for the design, analysis, and measurement of software safety are not yet available. Some past software failures, future NASA software trends, software engineering methods, and tools and techniques for various software safety analyses are reviewed. Recommendations to NASA are made based on this review.

  7. Systems Safety and Engineering Division (United States)

    Federal Laboratory Consortium — Volpe's Systems Safety and Engineering Division conducts engineering, research, and analysis to improve transportation safety, capacity, and resiliency. We provide...

  8. Cockpit emergency safety system (United States)

    Keller, Leo


    A comprehensive safety concept is proposed for aircraft's experiencing an incident to the development of fire and smoke in the cockpit. Fire or excessive heat development caused by malfunctioning electrical appliance may produce toxic smoke, may reduce the clear vision to the instrument panel and may cause health-critical respiration conditions. Immediate reaction of the crew, safe respiration conditions and a clear undisturbed view to critical flight information data can be assumed to be the prerequisites for a safe emergency landing. The personal safety equipment of the aircraft has to be effective in supporting the crew to divert the aircraft to an alternate airport in the shortest possible amount of time. Many other elements in the cause-and-effect context of the emergence of fire, such as fire prevention, fire detection, the fire extinguishing concept, systematic redundancy, the wiring concept, the design of the power supplying system and concise emergency checklist procedures are briefly reviewed, because only a comprehensive and complete approach will avoid fatal accidents of complex aircraft in the future.

  9. Aviation Safety Hotline Information System - (United States)

    Department of Transportation — The Aviation Safety Hotline Information System (ASHIS) collects, stores, and retrieves reports submitted by pilots, mechanics, cabin crew, passengers, or the public...

  10. Air Operators’ Safety Assurance System

    Directory of Open Access Journals (Sweden)

    Xie Zhi-Hui


    Full Text Available Construction of air operators’ safety assurance system is important for national civil aviation authority to perform the safety oversight work systematically and efficiently on the air operators. The system is a combination of management process, tools, information platform, which utilize system configuration model and data collection tools to accomplish the air operator system design evaluation and performance evaluation, and output the advice for national civil aviation authority inspectors to take action to improve the air operators’ safety design and performance according to the regulation. Process has been designed to realize design and performance evaluation, and strengthen the safety assurance function during the air operator certification and surveillance phases. Based on the system configuration model, risk indicators, data collection tools and other tools, the system could perform configuration setting, planning, task assignment, data collection, analysis and action during the certification and surveillance. The application of the safety assurance system to different operators has been considered.

  11. System safety education focused on system management (United States)

    Grose, V. L.


    System safety is defined and characteristics of the system are outlined. Some of the principle characteristics include role of humans in hazard analysis, clear language for input and output, system interdependence, self containment, and parallel analysis of elements.

  12. Software Safety Risk in Legacy Safety-Critical Computer Systems (United States)

    Hill, Janice L.; Baggs, Rhoda


    Safety Standards contain technical and process-oriented safety requirements. Technical requirements are those such as "must work" and "must not work" functions in the system. Process-Oriented requirements are software engineering and safety management process requirements. Address the system perspective and some cover just software in the system > NASA-STD-8719.13B Software Safety Standard is the current standard of interest. NASA programs/projects will have their own set of safety requirements derived from the standard. Safety Cases: a) Documented demonstration that a system complies with the specified safety requirements. b) Evidence is gathered on the integrity of the system and put forward as an argued case. [Gardener (ed.)] c) Problems occur when trying to meet safety standards, and thus make retrospective safety cases, in legacy safety-critical computer systems.

  13. CERN Safety System Monitoring - SSM

    CERN Document Server

    Hakulinen, T; Valentini, F; Gonzalez, J; Salatko-Petryszcze, C


    CERN SSM (Safety System Monitoring) [1] is a system for monitoring state-of-health of the various access and safety systems of the CERN site and accelerator infrastructure. The emphasis of SSM is on the needs of maintenance and system operation with the aim of providing an independent and reliable verification path of the basic operational parameters of each system. Included are all network-connected devices, such as PLCs, servers, panel displays, operator posts, etc. The basic monitoring engine of SSM is a freely available system-monitoring framework Zabbix [2], on top of which a simplified traffic-light-type web-interface has been built. The web-interface of SSM is designed to be ultra-light to facilitate access from handheld devices over slow connections. The underlying Zabbix system offers history and notification mechanisms typical of advanced monitoring systems.

  14. Future testing of active safety systems

    NARCIS (Netherlands)

    Hendriks, F.M.; Pelders, H.A.A.W.


    Active safety systems are increasingly becoming available in trucks and passenger vehicles. Developments in the field of active safety are shifting from increasing driver comfort towards increasing occupant safety. Furthermore, this shift is seen within active safety systems: safety functions are

  15. Safety design guide for safety related systems for CANDU 9

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young [Korea Atomic Energy Research Institute, Daeduk (Korea, Republic of); Wright, A.C.D. [Atomic Energy of Canada Ltd., Toronto (Canada)


    In general, two types of safety related systems and structures exist in the nuclear plant; The one is a systems and structures which perform safety functions during the normal operation of the plant, and the other is a systems and structures which perform safety functions to mitigate events caused by failure of the normally operating systems or by naturally occurring phenomena. In this safety design guide, these systems are identified in detail, and the major events for which the safety functions are required and the major safety requirements are identified in the list. As the probabilistic safety assessments are completed during the course of the project, additions or deletions to the list may be justified. 3 tabs. (Author) .new.

  16. System safety education focused on industrial engineering (United States)

    Johnston, W. L.; Morris, R. S.


    An educational program, designed to train students with the specific skills needed to become safety specialists, is described. The discussion concentrates on application, selection, and utilization of various system safety analytical approaches. Emphasis is also placed on the management of a system safety program, its relationship with other disciplines, and new developments and applications of system safety techniques.

  17. Software Safety Risk in Legacy Safety-Critical Computer Systems (United States)

    Hill, Janice; Baggs, Rhoda


    Safety-critical computer systems must be engineered to meet system and software safety requirements. For legacy safety-critical computer systems, software safety requirements may not have been formally specified during development. When process-oriented software safety requirements are levied on a legacy system after the fact, where software development artifacts don't exist or are incomplete, the question becomes 'how can this be done?' The risks associated with only meeting certain software safety requirements in a legacy safety-critical computer system must be addressed should such systems be selected as candidates for reuse. This paper proposes a method for ascertaining formally, a software safety risk assessment, that provides measurements for software safety for legacy systems which may or may not have a suite of software engineering documentation that is now normally required. It relies upon the NASA Software Safety Standard, risk assessment methods based upon the Taxonomy-Based Questionnaire, and the application of reverse engineering CASE tools to produce original design documents for legacy systems.

  18. Firefighter Safety for PV Systems

    DEFF Research Database (Denmark)

    Mathe, Laszlo; Sera, Dezso; Spataru, Sergiu


    An important and highly discussed safety issue for photovoltaic (PV) systems is that as long as the PV panels are illuminated, a high voltage is present at the PV string terminals and cables between the string and inverters that is independent of the state of the inverter's dc disconnection switch....... The presence of these energized conductors on the dc side of the PV system can pose a danger to anyone performing maintenance or firefighting....

  19. The ATLAS Detector Safety System

    CERN Multimedia

    Helfried Burckhart; Kathy Pommes; Heidi Sandaker

    The ATLAS Detector Safety System (DSS) has the mandate to put the detector in a safe state in case an abnormal situation arises which could be potentially dangerous for the detector. It covers the CERN alarm severity levels 1 and 2, which address serious risks for the equipment. The highest level 3, which also includes danger for persons, is the responsibility of the CERN-wide system CSAM, which always triggers an intervention by the CERN fire brigade. DSS works independently from and hence complements the Detector Control System, which is the tool to operate the experiment. The DSS is organized in a Front- End (FE), which fulfills autonomously the safety functions and a Back-End (BE) for interaction and configuration. The overall layout is shown in the picture below. ATLAS DSS configuration The FE implementation is based on a redundant Programmable Logical Crate (PLC) system which is used also in industry for such safety applications. Each of the two PLCs alone, one located underground and one at the s...

  20. System Safety Analysis Application Guide. Safety Analysis Report Update Program

    Energy Technology Data Exchange (ETDEWEB)


    Martin Marietta Energy Systems, Inc., (Energy Systems) is committed to performing and documenting safety analyses for facilities it manages for the Department of Energy (DOE). Safety analyses are performed to identify hazards and potential accidents; to analyze the adequacy of measures taken to eliminate, control, or mitigate hazards; and to evaluate potential accidents and determine associated risks. Safety Analysis Reports (SARs) are prepared to document the safety analysis to ensure facilities can be operated safely and in accordance with regulations. SARs include Technical Safety Requirements (TSRs), which are specific technical and administrative requirements that prescribe limits and controls to ensure safe operation of DOE facilities. These documented descriptions and analyses contribute to the authorization basis for facility operation. Energy Systems has established a process to perform Unreviewed Safety Question Determinations (USQDs) for planned changes and as-found conditions that are not described and analyzed in existing safety analyses. The process evaluates changes and as-found conditions to determine whether revisions to the authorization basis must be reviewed and approved by DOE. There is an Unreviewed Safety Question (USQ) if a change introduces conditions not bounded by the facility authorization basis. When it is necessary to request DOE approval to revise the authorization basis, preparation of a System Safety Analysis (SSA) is recommended. This application guide describes the process of preparing an SSA and the desired contents of an SSA. Guidance is provided on how to identify items and practices which are important to safety; how to determine the credibility and significance of consequences of proposed accident scenarios; how to evaluate accident prevention and mitigation features of the planned change; and how to establish special requirements to ensure that a change can be implemented with adequate safety.

  1. 76 FR 14592 - Safety Management System; Withdrawal (United States)


    ... in response to the ANPRM. The comment period closed on October 21, 2009. The Airline Safety and..., and 145 RIN 2120-AJ15 Safety Management System; Withdrawal AGENCY: Federal Aviation Administration... (``product/ service providers'') to develop a Safety Management System (SMS). The FAA is withdrawing the...

  2. Comprehensive Lifecycle for Assuring System Safety (United States)

    Knight, John C.; Rowanhill, Jonathan C.


    CLASS is a novel approach to the enhancement of system safety in which the system safety case becomes the focus of safety engineering throughout the system lifecycle. CLASS also expands the role of the safety case across all phases of the system's lifetime, from concept formation to decommissioning. As CLASS has been developed, the concept has been generalized to a more comprehensive notion of assurance becoming the driving goal, where safety is an important special case. This report summarizes major aspects of CLASS and contains a bibliography of papers that provide additional details.


    Energy Technology Data Exchange (ETDEWEB)



    In 2007, the Department of Energy (DOE) identified safety culture as one of their top Integrated Safety Management System (ISMS) related priorities. A team was formed to address this issue. The team identified a consensus set of safety culture principles, along with implementation practices that could be used by DOE, NNSA, and their contractors. Documented improvement tools were identified and communicated to contractors participating in a year long pilot project. After a year, lessons learned will be collected and a path forward determined. The goal of this effort was to achieve improved safety and mission performance through ISMS continuous improvement. The focus of ISMS improvement was safety culture improvement building on operating experience from similar industries such as the domestic and international commercial nuclear and chemical industry.

  4. Automation for System Safety Analysis (United States)

    Malin, Jane T.; Fleming, Land; Throop, David; Thronesbery, Carroll; Flores, Joshua; Bennett, Ted; Wennberg, Paul


    This presentation describes work to integrate a set of tools to support early model-based analysis of failures and hazards due to system-software interactions. The tools perform and assist analysts in the following tasks: 1) extract model parts from text for architecture and safety/hazard models; 2) combine the parts with library information to develop the models for visualization and analysis; 3) perform graph analysis and simulation to identify and evaluate possible paths from hazard sources to vulnerable entities and functions, in nominal and anomalous system-software configurations and scenarios; and 4) identify resulting candidate scenarios for software integration testing. There has been significant technical progress in model extraction from Orion program text sources, architecture model derivation (components and connections) and documentation of extraction sources. Models have been derived from Internal Interface Requirements Documents (IIRDs) and FMEA documents. Linguistic text processing is used to extract model parts and relationships, and the Aerospace Ontology also aids automated model development from the extracted information. Visualizations of these models assist analysts in requirements overview and in checking consistency and completeness.

  5. Architecture Level Safety Analyses for Safety-Critical Systems

    Directory of Open Access Journals (Sweden)

    K. S. Kushal


    Full Text Available The dependency of complex embedded Safety-Critical Systems across Avionics and Aerospace domains on their underlying software and hardware components has gradually increased with progression in time. Such application domain systems are developed based on a complex integrated architecture, which is modular in nature. Engineering practices assured with system safety standards to manage the failure, faulty, and unsafe operational conditions are very much necessary. System safety analyses involve the analysis of complex software architecture of the system, a major aspect in leading to fatal consequences in the behaviour of Safety-Critical Systems, and provide high reliability and dependability factors during their development. In this paper, we propose an architecture fault modeling and the safety analyses approach that will aid in identifying and eliminating the design flaws. The formal foundations of SAE Architecture Analysis & Design Language (AADL augmented with the Error Model Annex (EMV are discussed. The fault propagation, failure behaviour, and the composite behaviour of the design flaws/failures are considered for architecture safety analysis. The illustration of the proposed approach is validated by implementing the Speed Control Unit of Power-Boat Autopilot (PBA system. The Error Model Annex (EMV is guided with the pattern of consideration and inclusion of probable failure scenarios and propagation of fault conditions in the Speed Control Unit of Power-Boat Autopilot (PBA. This helps in validating the system architecture with the detection of the error event in the model and its impact in the operational environment. This also provides an insight of the certification impact that these exceptional conditions pose at various criticality levels and design assurance levels and its implications in verifying and validating the designs.

  6. Among High School Seniors, Driving After Marijuana Use Surpasses Drunk Driving (United States)

    ... Driving After Marijuana Use Surpasses Drunk Driving Among High School Seniors, Driving After Marijuana Use Surpasses Drunk Driving ... NIDA Notes Contributing Writer Nearly 1 in 6 high school seniors who responded to a 2011 survey reported ...

  7. Opportunistic Sensing in Train Safety Systems

    NARCIS (Netherlands)

    Scholten, Johan; Bakker, Pascal


    Train safety systems are complex and expensive, and changing them requires huge investments. Changes are evolutionary and small. Current developments, like faster - high speed - trains and a higher train density on the railway network, have initiated research on safety systems that can cope with the

  8. 77 FR 70409 - System Safety Program (United States)


    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF TRANSPORTATION Federal Railroad Administration 49 CFR Part 270 2130-AC31 System Safety Program AGENCY: Federal Railroad... commuter and intercity passenger railroads to develop and implement a system safety program (SSP) to...

  9. Verifying therapy safety interlock system with spin

    CSIR Research Space (South Africa)

    Seotsanyana, M


    Full Text Available on the successful use of model checking in the design and verification of the Safety Interlock System (SIS) at iThemba LABS. SIS is part of proton therapy control system (TCS) and its main task is to monitor and evaluate the safety conditions in the TCS as a whole...

  10. Systems Thinking and Patient Safety

    National Research Council Canada - National Science Library

    Schyve, Paul M


    Patient safety is a prominent theme in health care delivery today. This should come as no surprise, given that "first, do no harm" has been the ethical watchword throughout the history of medicine, nursing, and pharmacy...

  11. Recommendations for the LHC safety alarm system

    CERN Document Server

    Laeger, H


    A working group was set up to define the LHC safety alarm system, also known as Alarm-of-Level-3-System (AL3S). The mandate asked for recommendations to be elaborated on four items: the overall concept of the AL3S for machine and experiments, the transmission and display of safety alarms, the AL3S during civil engineering construction, and the transition from the present LEP to the final LHC safety alarm system. The members of the working group represented a wide range of interest and experience including the CERN Fire Brigade, safety officers from experiments and machines, and specialists for safety and control systems. The recommendations highlight the need for a clear definition of responsibilities and procedures, well-engineered homogeneous systems across CERN, and they point to several important issues outside the mandate of the working group. These recommendations were presented, discussed and accepted by several CERN and LHC committees.

  12. Computer system reliability safety and usability

    CERN Document Server

    Dhillon, BS


    Computer systems have become an important element of the world economy, with billions of dollars spent each year on development, manufacture, operation, and maintenance. Combining coverage of computer system reliability, safety, usability, and other related topics into a single volume, Computer System Reliability: Safety and Usability eliminates the need to consult many different and diverse sources in the hunt for the information required to design better computer systems.After presenting introductory aspects of computer system reliability such as safety, usability-related facts and figures,

  13. Safety-critical Java for embedded systems

    DEFF Research Database (Denmark)

    Schoeberl, Martin; Dalsgaard, Andreas Engelbredt; Hansen, René Rydhof


    This paper presents the motivation for and outcomes of an engineering research project on certifiable Javafor embedded systems. The project supports the upcoming standard for safety-critical Java, which defines asubset of Java and libraries aiming for development of high criticality systems....... The outcome of this projectinclude prototype safety-critical Java implementations, a time-predictable Java processor, analysis tools formemory safety, and example applications to explore the usability of safety-critical Java for this applicationarea. The text summarizes developments and key contributions...


    Directory of Open Access Journals (Sweden)



    Full Text Available In order to increase the confidence of the trading partners and consumers in the products which are sold on the market, enterprises producing food are required to implement the food safety system HACCP,a particularly useful system because the manufacturer is not able to fully control finished products . SR EN ISO 22000:2005 establishes requirements for a food safety management system where an organization in the food chain needs to proove its ability to control food safety hazards in order to ensure that food is safe at the time of human consumption. This paper presents the main steps which ensure food safety using the HACCP system, and SR EN ISO 20000:2005 requirements for food safety.

  15. Integrating system safety into the basic systems engineering process (United States)

    Griswold, J. W.


    The basic elements of a systems engineering process are given along with a detailed description of what the safety system requires from the systems engineering process. Also discussed is the safety that the system provides to other subfunctions of systems engineering.

  16. NASA Aviation Safety Reporting System (ASRS) (United States)

    Connell, Linda J.


    The NASA Aviation Safety Reporting System (ASRS) collects, analyzes, and distributes de-identified safety information provided through confidentially submitted reports from frontline aviation personnel. Since its inception in 1976, the ASRS has collected over 1.4 million reports and has never breached the identity of the people sharing their information about events or safety issues. From this volume of data, the ASRS has released over 6,000 aviation safety alerts concerning potential hazards and safety concerns. The ASRS processes these reports, evaluates the information, and provides selected de-identified report information through the online ASRS Database at The NASA ASRS is also a founding member of the International Confidential Aviation Safety Systems (ICASS) group which is a collection of other national aviation reporting systems throughout the world. The ASRS model has also been replicated for application to improving safety in railroad, medical, fire fighting, and other domains. This presentation will discuss confidential, voluntary, and non-punitive reporting systems and their advantages in providing information for safety improvements.

  17. Prestandardisation Activities for Computer Based Safety Systems

    DEFF Research Database (Denmark)

    Taylor, J. R.; Bologna, S.; Ehrenberger, W.


    Questions of technical safety become more and more important. Due to the higher complexity of their functions computer based safety systems have special problems. Researchers, producers, licensing personnel and customers have met on a European basis to exchange knowledge and formulate positions...

  18. From Safe Systems to Patient Safety

    DEFF Research Database (Denmark)

    Aarts, J.; Nøhr, C.


    for the third conference with the theme: The ability to design, implement and evaluate safe, useable and effective systems within complex health care organizations. The theme for this conference was "Designing and Implementing Health IT: from safe systems to patient safety". The contributions have reflected...... and implementation of safe systems and thus contribute to the agenda of patient safety? The contributions demonstrate how the health informatics community has contributed to the performance of significant research and to translating research findings to develop health care delivery and improve patient safety...

  19. Safety status system for operating room devices. (United States)

    Guédon, Annetje C P; Wauben, Linda S G L; Overvelde, Marlies; Blok, Joleen H; van der Elst, Maarten; Dankelman, Jenny; van den Dobbelsteen, John J


    Since the increase of the number of technological aids in the operating room (OR), equipment-related incidents have come to be a common kind of adverse events. This underlines the importance of adequate equipment management to improve the safety in the OR. A system was developed to monitor the safety status (periodic maintenance and registered malfunctions) of OR devices and to facilitate the notification of malfunctions. The objective was to assess whether the system is suitable for use in an busy OR setting and to analyse its effect on the notification of malfunctions. The system checks automatically the safety status of OR devices through constant communication with the technical facility management system, informs the OR staff real-time and facilitates notification of malfunctions. The system was tested for a pilot period of six months in four ORs of a Dutch teaching hospital and 17 users were interviewed on the usability of the system. The users provided positive feedback on the usability. For 86.6% of total time, the localisation of OR devices was accurate. 62 malfunctions of OR devices were reported, an increase of 12 notifications compared to the previous year. The safety status system was suitable for an OR complex, both from a usability and technical point of view, and an increase of reported malfunctions was observed. The system eases monitoring the safety status of equipment and is a promising tool to improve the safety related to OR devices.

  20. Aviation Safety Reporting System: Process and Procedures (United States)

    Connell, Linda J.


    The Aviation Safety Reporting System (ASRS) was established in 1976 under an agreement between the Federal Aviation Administration (FAA) and the National Aeronautics and Space Administration (NASA). This cooperative safety program invites pilots, air traffic controllers, flight attendants, maintenance personnel, and others to voluntarily report to NASA any aviation incident or safety hazard. The FAA provides most of the program funding. NASA administers the program, sets its policies in consultation with the FAA and aviation community, and receives the reports submitted to the program. The FAA offers those who use the ASRS program two important reporting guarantees: confidentiality and limited immunity. Reports sent to ASRS are held in strict confidence. More than 350,000 reports have been submitted since the program's beginning without a single reporter's identity being revealed. ASRS removes all personal names and other potentially identifying information before entering reports into its database. This system is a very successful, proof-of-concept for gathering safety data in order to provide timely information about safety issues. The ASRS information is crucial to aviation safety efforts both nationally and internationally. It can be utilized as the first step in safety by providing the direction and content to informed policies, procedures, and research, especially human factors. The ASRS process and procedures will be presented as one model of safety reporting feedback systems.

  1. Proactive Management of Aviation System Safety Risk (United States)

    National Aeronautics and Space Administration — Aviation safety systems have undergone dramatic changes over the past fifty years. If you take a look at the early technology in this area, you'll see that there was...

  2. CDC STATE System Tobacco Legislation - Fire Safety (United States)

    U.S. Department of Health & Human Services — 1995-2017. Centers for Disease Control and Prevention (CDC). State Tobacco Activities Tracking and Evaluation (STATE) System. Legislation – Fire-Safety. The STATE...

  3. Diagnosis operational safety of a transport system

    Directory of Open Access Journals (Sweden)

    Maciej WOROPAY


    Full Text Available The transport systems are sociotechnical systems in which the direct realization of the tasks is dealt with by an executive subsystem consisting of the elementary subsystems of a human – a technical object (an operator – a means of transport type realizing the tasks within the system environment. In respect of a human located within a transport system the most significant criterion in the evaluation of transport being realized is their safety.The safety level of the task realization is influenced by the risks resulting from the interaction of the forcing factors, affecting an elementary executive subsystem.These factors may be divided into [8]:-working;-external;-antropotechnical.Due to the complexity of the systems being analysed in the paper, it has been attempted to evaluate the influence of the forcing factors on the safety of this system operation.

  4. Design of an Active Automotive Safety System

    Directory of Open Access Journals (Sweden)

    Y. Wang


    Full Text Available With the development of the national economy, the people's standard of living got corresponding improvement, cars has been one of the indispensable traffic tools in many families. An active safety system is proposed, which can real-time detect the vehicle's running status and judge the security status of the vehicle. The system, which takes single-chip microcomputer as the controlling core and combines with millimeter-wave and ultrasonic distance measurement technology, can detect the distance from vehicle to vehicle and judge the security status of the vehicle. The hardware composition of the system and the data acquiring circuit are proposed, the mathematic model for different situation is established, and the controlling algorithm is completed. This system can accurately measure speed and distance between vehicles; the active safety control system can meet the relevant data measurement and transmission requirement; and can meet the functional requirement of the active safety control system

  5. System for controlling child safety seat environment (United States)

    Dabney, Richard W. (Inventor); Elrod, Susan V. (Inventor)


    A system is provided to control the environment experienced by a child in a child safety seat. Each of a plurality of thermoelectric elements is individually controllable to be one of heated and cooled relative to an ambient temperature. A first portion of the thermoelectric elements are positioned on the child safety seat such that a child sitting therein is positioned thereover. A ventilator coupled to the child safety seat moves air past a second portion of the thermoelectric elements and filters the air moved therepast. One or more jets coupled to the ventilator receive the filtered air. Each jet is coupled to the child safety seat and can be positioned to direct the heated/cooled filtered air to the vicinity of the head of the child sitting in the child safety seat.

  6. Classification of Aeronautics System Health and Safety Documents (United States)

    National Aeronautics and Space Administration — Most complex aerospace systems have many text reports on safety, maintenance, and associated issues. The Aviation Safety Reporting System (ASRS) spans several...

  7. K West integrated water treatment system subproject safety analysis document

    Energy Technology Data Exchange (ETDEWEB)



    This Accident Analysis evaluates unmitigated accident scenarios, and identifies Safety Significant and Safety Class structures, systems, and components for the K West Integrated Water Treatment System.

  8. System Safety in an IT Service Organization (United States)

    Parsons, Mike; Scutt, Simon

    Within Logica UK, over 30 IT service projects are considered safetyrelated. These include operational IT services for airports, railway infrastructure asset management, nationwide radiation monitoring and hospital medical records services. A recent internal audit examined the processes and documents used to manage system safety on these services and made a series of recommendations for improvement. This paper looks at the changes and the challenges to introducing them, especially where the service is provided by multiple units supporting both safety and non-safety related services from multiple locations around the world. The recommendations include improvements to service agreements, improved process definitions, routine safety assessment of changes, enhanced call logging, improved staff competency and training, and increased safety awareness. Progress is reported as of today, together with a road map for implementation of the improvements to the service safety management system. A proposal for service assurance levels (SALs) is discussed as a way forward to cover the wide variety of services and associated safety risks.

  9. Reflections on system safety and the law (United States)

    Hayes, D. F., Sr.


    The application of law to the determination of what constitutes safeness is discussed. The numerous factors are analyzed which enter into the decisions of courts in deciding what is safe and what is unsafe. It is pointed out that as technology changes, legal interpretations of safety also change. Arguements are given for the use of system safety techniques and better engineering analyses as instruments of defense against liability.

  10. Safety Verification for Probabilistic Hybrid Systems

    DEFF Research Database (Denmark)

    Zhang, Lijun; She, Zhikun; Ratschan, Stefan


    hybrid systems and develop a general abstraction technique for verifying probabilistic safety problems. This gives rise to the first mechanisable technique that can, in practice, formally verify safety properties of non-trivial continuous-time stochastic hybrid systems-without resorting to point......-wise discretisation. Moreover, being based on arbitrary abstractions computed by tools for the analysis of non-probabilistic hybrid systems, improvements in effectivity of such tools directly carry over to improvements in effectivity of the technique we describe. We demonstrate the applicability of our approach...

  11. Integrated safety management system verification: Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, R.F.


    Department of Energy (DOE) Policy (P) 450.4, Safety Management System Policy, commits to institutionalization of an Integrated Safety Management System (ISMS) throughout the DOE complex. The DOE Acquisition Regulations (DEAR, 48 CFR 970) requires contractors to manage and perform work in accordance with a documented Integrated Safety Management System (ISMS). Guidance and expectations have been provided to PNNL by incorporation into the operating contract (Contract DE-ACM-76FL0 1830) and by letter. The contract requires that the contractor submit a description of their ISMS for approval by DOE. PNNL submitted their proposed Safety Management System Description for approval on November 25,1997. RL tentatively approved acceptance of the description pursuant to a favorable recommendation from this review. The Integrated Safety Management System Verification is a review of the adequacy of the ISMS description in fulfilling the requirements of the DEAR and the DOE Policy. The purpose of this review is to provide the Richland Operations Office Manager with a recommendation for approval of the ISMS description of the Pacific Northwest Laboratory based upon compliance with the requirements of 49 CFR 970.5204(-2 and -78); and to verify the extent and maturity of ISMS implementation within the Laboratory. Further the review will provide a model for other DOE laboratories managed by the Office of Assistant Secretary for Energy Research.

  12. Traffic safety effects of navigation systems

    NARCIS (Netherlands)

    Feenstra, P.J.; Hogema, J.H.; Vonk, T.


    Abstract— To investigate effects of navigation systems on traffic safety, a literature search, a damages database analysis, a user survey and an instrumented car study were conducted. This paper presents the instrumented car study to investigate the effects of a navigation system on driving behavior

  13. Safety Analysis of Stochastic Dynamical Systems

    DEFF Research Database (Denmark)

    Sloth, Christoffer; Wisniewski, Rafael


    This paper presents a method for verifying the safety of a stochastic system. In particular, we show how to compute the largest set of initial conditions such that a given stochastic system is safe with probability p. To compute the set of initial conditions we rely on the moment method that via...

  14. Applying Systems Thinking to Law Enforcement Safety: Recommendation for a Comprehensive Safety Management Framework (United States)


    THINKING TO LAW ENFORCEMENT SAFETY: RECOMMENDATION FOR A COMPREHENSIVE SAFETY MANAGEMENT FRAMEWORK by Maggie A. DeBoard December 2015...2. REPORT DATE December 2015 3. REPORT TYPE AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE APPLYING SYSTEMS THINKING TO LAW...deaths, systems thinking , safety management systems, risk management, fire safety officer, after-action review, firefighter culture, OSHA

  15. Recent advances in systems safety and security

    CERN Document Server

    Stamatescu, Grigore


    This book represents a timely overview of advances in systems safety and security, based on selected, revised and extended contributions from the 2nd and 3rd editions of the International Workshop on Systems Safety and Security – IWSSS, held in 2014 and 2015, respectively, in Bucharest, Romania. It includes 14 chapters, co-authored by 34 researchers from 7 countries. The book provides an useful reference from both theoretical and applied perspectives in what concerns recent progress in this area of critical interest. Contributions, broadly grouped by core topic, address challenges related to information theoretic methods for assuring systems safety and security, cloud-based solutions, image processing approaches, distributed sensor networks and legal or risk analysis viewpoints. These are mostly accompanied by associated case studies providing additional practical value and underlying the broad relevance and impact of the field.

  16. Modelling safety of multistate systems with ageing components (United States)

    Kołowrocki, Krzysztof; Soszyńska-Budny, Joanna


    An innovative approach to safety analysis of multistate ageing systems is presented. Basic notions of the ageing multistate systems safety analysis are introduced. The system components and the system multistate safety functions are defined. The mean values and variances of the multistate systems lifetimes in the safety state subsets and the mean values of their lifetimes in the particular safety states are defined. The multi-state system risk function and the moment of exceeding by the system the critical safety state are introduced. Applications of the proposed multistate system safety models to the evaluation and prediction of the safty characteristics of the consecutive "m out of n: F" is presented as well.

  17. Safety effects of navigation systems.

    NARCIS (Netherlands)


    Increasing numbers of drivers are using navigation systems in their cars. The advantages to the user are obvious: you can get to your destination via the fastest and shortest route. This reduces stress and exposure to other traffic. However, there are also some (unintended) negative effects. For

  18. Integrated safety management system verification: Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, R.F.


    Department of Energy (DOE) Policy (P) 450.4, Safety Management System Policy, commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex. The DOE Acquisition Regulations (DEAR 48 CFR 970) requires contractors to manage and perform work in accordance with a documented Integrated Safety Management System. The Manager, Richland Operations Office (RL), initiated a combined Phase 1 and Phase 2 Integrated Safety Management Verification review to confirm that PNNL had successfully submitted a description of their ISMS and had implemented ISMS within the laboratory facilities and processes. A combined review was directed by the Manager, RL, based upon the progress PNNL had made in the implementation of ISM. This report documents the results of the review conducted to verify: (1) that the PNNL integrated safety management system description and enabling documents and processes conform to the guidance provided by the Manager, RL; (2) that corporate policy is implemented by line managers; (3) that PNNL has provided tailored direction to the facility management; and (4) the Manager, RL, has documented processes that integrate their safety activities and oversight with those of PNNL. The general conduct of the review was consistent with the direction provided by the Under Secretary`s Draft Safety Management System Review and Approval Protocol. The purpose of this review was to provide the Manager, RL, with a recommendation to the adequacy of the ISMS description of the Pacific Northwest Laboratory based upon compliance with the requirements of 49 CFR 970.5204(-2 and -78); and, to provide an evaluation of the extent and maturity of ISMS implementation within the Laboratory. Further, this review was intended to provide a model for other DOE Laboratories. In an effort to reduce the time and travel costs associated with ISM verification the team agreed to conduct preliminary training and orientation electronically and by phone. These

  19. 77 FR 11120 - Patient Safety Organizations: Voluntary Relinquishment From UAB Health System Patient Safety... (United States)


    ... HUMAN SERVICES Agency for Healthcare Research and Quality Patient Safety Organizations: Voluntary Relinquishment From UAB Health System Patient Safety Organization AGENCY: Agency for Healthcare Research and... relinquishment from the UAB Health System Patient Safety Organization of its status as a Patient Safety...

  20. Analysis and design on airport safety information management system

    Directory of Open Access Journals (Sweden)

    Yan Lin


    Full Text Available Airport safety information management system is the foundation of implementing safety operation, risk control, safety performance monitor, and safety management decision for the airport. The paper puts forward the architecture of airport safety information management system based on B/S model, focuses on safety information processing flow, designs the functional modules and proposes the supporting conditions for system operation. The system construction is helpful to perfecting the long effect mechanism driven by safety information, continually increasing airport safety management level and control proficiency.

  1. Information systems in food safety management

    NARCIS (Netherlands)

    McMeekin, T.A.; Baranyi, J.; Bowman, J.; Dalgaard, P.; Kirk, M.; Ross, T.; Schmid, S.; Zwietering, M.H.


    Information systems are concerned with data capture, storage, analysis and retrieval. In the context of food safety management they are vital to assist decision making in a short time frame, potentially allowing decisions to be made and practices to be actioned in real time. Databases with

  2. The safety potential of navigation systems.

    NARCIS (Netherlands)

    Oei, H.-l.


    This study deals with the possible negative and positive effects of navigation systems on road safety. The literature shows that the human factors side is open for improvement: the design of the menu, possibility of manual programming during driving and shifting the attention of the driver from the


    Directory of Open Access Journals (Sweden)

    Volodymyr Kharchenko


    Full Text Available The article deals with the analysis of the researches conducted in the field of safety management systems.Safety management system framework, methods and tools for safety analysis in Air Traffic Control have been reviewed.Principles of development of Integrated safety management system in Air Traffic Services have been proposed.

  4. A Unified System for Ensuring Drug Safety


    Cave, Neil G.


    There are currently two systems in the United States to ensure the safety of pharmaceutical products: tort and regulation. The shared goal of tort law and Food and Drug Administrative (“FDAâ€) regulation is to make beneficial drugs available to patients while keeping unsafe drugs off the market. This goal will be better served if the two are combined into a unified system, wherein each functions in the role best suited to its relative strengths and weaknesses. In...

  5. Formal Modeling of Safety Requirements in the Model-Driven Development of Safety Critical Embedded Systems


    Sojer, Dominik;Buckl, Christian;Knoll, Alois


    Safety requirements are a very important artifact in the developmentof safety critical embedded systems. They are usually identifiedduring safety analyses and are used by experts as a basis for thecorrect selection and implementation of safety mechanisms. Varioussafety analysis research groups have worked on formal modeling ofsafety requirements with the goal of determining if a system canmeet these requirements. In this abstract, we propose the applicationof formal models of safety requireme...

  6. Does the concept of safety culture help or hinder systems thinking in safety? (United States)

    Reiman, Teemu; Rollenhagen, Carl


    The concept of safety culture has become established in safety management applications in all major safety-critical domains. The idea that safety culture somehow represents a "systemic view" on safety is seldom explicitly spoken out, but nevertheless seem to linger behind many safety culture discourses. However, in this paper we argue that the "new" contribution to safety management from safety culture never really became integrated with classical engineering principles and concepts. This integration would have been necessary for the development of a more genuine systems-oriented view on safety; e.g. a conception of safety in which human, technological, organisational and cultural factors are understood as mutually interacting elements. Without of this integration, researchers and the users of the various tools and methods associated with safety culture have sometimes fostered a belief that "safety culture" in fact represents such a systemic view about safety. This belief is, however, not backed up by theoretical or empirical evidence. It is true that safety culture, at least in some sense, represents a holistic term-a totality of factors that include human, organisational and technological aspects. However, the departure for such safety culture models is still human and organisational factors rather than technology (or safety) itself. The aim of this paper is to critically review the various uses of the concept of safety culture as representing a systemic view on safety. The article will take a look at the concepts of culture and safety culture based on previous studies, and outlines in more detail the theoretical challenges in safety culture as a systems concept. The paper also presents recommendations on how to make safety culture more systemic. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Industrial Personal Computer based Display for Nuclear Safety System

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ji Hyeon; Kim, Aram; Jo, Jung Hee; Kim, Ki Beom; Cheon, Sung Hyun; Cho, Joo Hyun; Sohn, Se Do; Baek, Seung Min [KEPCO, Youngin (Korea, Republic of)


    The safety display of nuclear system has been classified as important to safety (SIL:Safety Integrity Level 3). These days the regulatory agencies are imposing more strict safety requirements for digital safety display system. To satisfy these requirements, it is necessary to develop a safety-critical (SIL 4) grade safety display system. This paper proposes industrial personal computer based safety display system with safety grade operating system and safety grade display methods. The description consists of three parts, the background, the safety requirements and the proposed safety display system design. The hardware platform is designed using commercially available off-the-shelf processor board with back plane bus. The operating system is customized for nuclear safety display application. The display unit is designed adopting two improvement features, i.e., one is to provide two separate processors for main computer and display device using serial communication, and the other is to use Digital Visual Interface between main computer and display device. In this case the main computer uses minimized graphic functions for safety display. The display design is at the conceptual phase, and there are several open areas to be concreted for a solid system. The main purpose of this paper is to describe and suggest a methodology to develop a safety-critical display system and the descriptions are focused on the safety requirement point of view.

  8. The Safety of Unmanned Systems: The Development of Safety Precepts for Unmanned Systems (UMS)

    National Research Council Canada - National Science Library

    English, Thomas P; Shampine, David J; Adams, Julie A; Muniak, Charles G; Kratovil, Edward W


    ...), and a concern for safety when these systems, primarily unmanned air vehicles, were operated over populated areas, or in proximity to other aircraft, both military and civilian, and when configured...

  9. System of its indicator economic safety


    Alexandrova, A.


    The thesis is devoted to the scientific and methodological decision of problem of formulation peculiarity economic safety’s guarantying of Ukraine in regional aspect. The scientific ground of optimization economic safety’s management are design. This work describes the bases of research economic safety, define the structure of this category, system of its indicators. Regional features of social and economical development are determined. Various between social and economical development of reg...

  10. Surpassing the Carnot efficiency by extracting imperfect work (United States)

    Ng, Nelly Huei Ying; Prebin Woods, Mischa; Wehner, Stephanie


    A suitable way of quantifying work for microscopic quantum systems has been constantly debated in the field of quantum thermodynamics. One natural approach is to measure the average increase in energy of an ancillary system, called the battery, after a work extraction protocol. The quality of energy extracted is usually argued to be good by quantifying higher moments of the energy distribution, or by restricting the amount of entropy to be low. This limits the amount of heat contribution to the energy extracted, but does not completely prevent it. We show that the definition of ‘work’ is crucial. If one allows for a definition of work that tolerates a non-negligible entropy increase in the battery, then a small scale heat engine can possibly exceed the Carnot efficiency. This can be done without using any additional resources such as coherence or correlations, and furthermore can be achieved even when one of the heat baths is finite in size.

  11. Daniel K. Inouye Solar Telescope system safety (United States)

    Hubbard, Robert P.; Bulau, Scott E.; Shimko, Steve; Williams, Timothy R.


    System safety for the Daniel K. Inouye Solar Telescope (DKIST) is the joint responsibility of a Maui-based safety team and the Tucson-based systems engineering group. The DKIST project is committed to the philosophy of "Safety by Design". To that end the project has implemented an aggressive hazard analysis, risk assessment, and mitigation system. It was initially based on MIL-STD-882D, but has since been augmented in a way that lends itself to direct application to the design of our Global Interlock System (GIS). This was accomplished by adopting the American National Standard for Industrial Robots and Robot Systems (ANSI/RIA R15.06) for all identified hazards that involve potential injury to personnel. In this paper we describe the details of our augmented hazard analysis system and its use by the project. Since most of the major hardware for the DKIST (e.g., the enclosure, and telescope mount assembly) has been designed and is being constructed by external contractors, the DKIST project has required our contractors to perform a uniform hazard analysis of their designs using our methods. This paper also describes the review and follow-up process implemented by the project that is applied to both internal and external subsystem designs. Our own weekly hazard analysis team meetings have now largely turned to system-level hazards and hazards related to specific tasks that will be encountered during integration, test, and commissioning and maintenance operations. Finally we discuss a few lessons learned, describing things we might do differently if we were starting over today.

  12. Total Quality Management and the System Safety Secretary (United States)

    Elliott, Suzan E.


    The system safety secretary is a valuable member of the system safety team. As downsizing occurs to meet economic constraints, the Total Quality Management (TQM) approach is frequently adopted as a formula for success and, in some cases, for survival.

  13. NASA System Safety Handbook. Volume 1; System Safety Framework and Concepts for Implementation (United States)

    Dezfuli, Homayoon; Benjamin, Allan; Everett, Christopher; Smith, Curtis; Stamatelatos, Michael; Youngblood, Robert


    System safety assessment is defined in NPR 8715.3C, NASA General Safety Program Requirements as a disciplined, systematic approach to the analysis of risks resulting from hazards that can affect humans, the environment, and mission assets. Achievement of the highest practicable degree of system safety is one of NASA's highest priorities. Traditionally, system safety assessment at NASA and elsewhere has focused on the application of a set of safety analysis tools to identify safety risks and formulate effective controls.1 Familiar tools used for this purpose include various forms of hazard analyses, failure modes and effects analyses, and probabilistic safety assessment (commonly also referred to as probabilistic risk assessment (PRA)). In the past, it has been assumed that to show that a system is safe, it is sufficient to provide assurance that the process for identifying the hazards has been as comprehensive as possible and that each identified hazard has one or more associated controls. The NASA Aerospace Safety Advisory Panel (ASAP) has made several statements in its annual reports supporting a more holistic approach. In 2006, it recommended that "... a comprehensive risk assessment, communication and acceptance process be implemented to ensure that overall launch risk is considered in an integrated and consistent manner." In 2009, it advocated for "... a process for using a risk-informed design approach to produce a design that is optimally and sufficiently safe." As a rationale for the latter advocacy, it stated that "... the ASAP applauds switching to a performance-based approach because it emphasizes early risk identification to guide designs, thus enabling creative design approaches that might be more efficient, safer, or both." For purposes of this preface, it is worth mentioning three areas where the handbook emphasizes a more holistic type of thinking. First, the handbook takes the position that it is important to not just focus on risk on an individual

  14. An Integrated Project Management Life Cycle Supporting System Safety (United States)

    Tschürtz, Hans; Schedl, Gabriele

    System failures in safety-critical domains can lead to harmful consequences for humans, the environment and for the system itself. The field of 'system safety' provides relief and aims at identifying possible risks already during the project planning phase of the system development. This requires modern project management support. The realisation of innovative ideas in software often in-creases the complexity and increasingly leads to dangerous system states or even system failures that put the safety of the system at risk.

  15. Quantum Metrology: Surpassing the shot-noise limit with Dzyaloshinskii-Moriya interaction. (United States)

    Ozaydin, Fatih; Altintas, Azmi Ali


    Entanglement is at the heart of quantum technologies such as quantum information and quantum metrology. Providing larger quantum Fisher information (QFI), entangled systems can be better resources than separable systems in quantum metrology. However the effects on the entanglement dynamics such as decoherence usually decrease the QFI considerably. On the other hand, Dzyaloshinskii-Moriya (DM) interaction has been shown to excite entanglement. Since an increase in entanglement does not imply an increase in QFI, and also there are cases where QFI decreases as entanglement increases, it is interesting to study the influence of DM interaction on quantum metrology. In this work, we study the QFI of thermal entanglement of two-qubit and three-qubit Heisenberg models with respect to SU(2) rotations. We show that even at high temperatures, DM interaction excites QFI of both ferromagnetic and antiferromagnetic models. We also show that QFI of the ferromagnetic model of two qubits can surpass the shot-noise limit of the separable states, while QFI of the antiferromagnetic model in consideration can only approach to the shot-noise limit. Our results open new insights in quantum metrology with Heisenberg models.



    Başaran, Burhan


    The increase in the level of welfare of the countriesand the awareness of the consumers have forced the firms in the food sector toseek for new pursuits. In this re­gard, ISO 22000 is the most commonlypreferred food safety system. This study aims to contribute the share­holdersand the researchers studying this topic by in­terpreting the lateststudies in this field and determine the critical relationships inorder to picture an effective and productive implementation ofISO22000 which is one of ...

  17. Information systems in food safety management. (United States)

    McMeekin, T A; Baranyi, J; Bowman, J; Dalgaard, P; Kirk, M; Ross, T; Schmid, S; Zwietering, M H


    Information systems are concerned with data capture, storage, analysis and retrieval. In the context of food safety management they are vital to assist decision making in a short time frame, potentially allowing decisions to be made and practices to be actioned in real time. Databases with information on microorganisms pertinent to the identification of foodborne pathogens, response of microbial populations to the environment and characteristics of foods and processing conditions are the cornerstone of food safety management systems. Such databases find application in: Identifying pathogens in food at the genus or species level using applied systematics in automated ways. Identifying pathogens below the species level by molecular subtyping, an approach successfully applied in epidemiological investigations of foodborne disease and the basis for national surveillance programs. Predictive modelling software, such as the Pathogen Modeling Program and Growth Predictor (that took over the main functions of Food Micromodel) the raw data of which were combined as the genesis of an international web based searchable database (ComBase). Expert systems combining databases on microbial characteristics, food composition and processing information with the resulting "pattern match" indicating problems that may arise from changes in product formulation or processing conditions. Computer software packages to aid the practical application of HACCP and risk assessment and decision trees to bring logical sequences to establishing and modifying food safety management practices. In addition there are many other uses of information systems that benefit food safety more globally, including: Rapid dissemination of information on foodborne disease outbreaks via websites or list servers carrying commentary from many sources, including the press and interest groups, on the reasons for and consequences of foodborne disease incidents. Active surveillance networks allowing rapid dissemination

  18. Safety-Critical Java for Embedded Systems

    DEFF Research Database (Denmark)

    Rios Rivas, Juan Ricardo

    for Java aims at providing a reduced set of the Java programming language that can be used for systems that need to be certified at the highest levels of criticality. Safety-critical Java (SCJ) restricts how a developer can structure an application by providing a specific programming model...... and by restricting the set of methods and libraries that can be used. Furthermore, its memory model do not use a garbage-collected heap but scoped memories. In this thesis we examine the use of the SCJ specification through an implementation in a time-predictable, FPGA-based Java processor. The specification is now...

  19. Design for safety: theoretical framework of the safety aspect of BIM system to determine the safety index

    Directory of Open Access Journals (Sweden)

    Ai Lin Evelyn Teo


    Full Text Available Despite the safety improvement drive that has been implemented in the construction industry in Singapore for many years, the industry continues to report the highest number of workplace fatalities, compared to other industries. The purpose of this paper is to discuss the theoretical framework of the safety aspect of a proposed BIM System to determine a Safety Index. An online questionnaire survey was conducted to ascertain the current workplace safety and health situation in the construction industry and explore how BIM can be used to improve safety performance in the industry. A safety hazard library was developed based on the main contributors to fatal accidents in the construction industry, determined from the formal records and existing literature, and a series of discussions with representatives from the Workplace Safety and Health Institute (WSH Institute in Singapore. The results from the survey suggested that the majority of the firms have implemented the necessary policies, programmes and procedures on Workplace Safety and Health (WSH practices. However, BIM is still not widely applied or explored beyond the mandatory requirement that building plans should be submitted to the authorities for approval in BIM format. This paper presents a discussion of the safety aspect of the Intelligent Productivity and Safety System (IPASS developed in the study. IPASS is an intelligent system incorporating the buildable design concept, theory on the detection, prevention and control of hazards, and the Construction Safety Audit Scoring System (ConSASS. The system is based on the premise that safety should be considered at the design stage, and BIM can be an effective tool to facilitate the efforts to enhance safety performance. IPASS allows users to analyse and monitor key aspects of the safety performance of the project before the project starts and as the project progresses.

  20. Modelling safety of multistate systems with ageing components

    Energy Technology Data Exchange (ETDEWEB)

    Kołowrocki, Krzysztof; Soszyńska-Budny, Joanna [Gdynia Maritime University, Department of Mathematics ul. Morska 81-87, Gdynia 81-225 Poland (Poland)


    An innovative approach to safety analysis of multistate ageing systems is presented. Basic notions of the ageing multistate systems safety analysis are introduced. The system components and the system multistate safety functions are defined. The mean values and variances of the multistate systems lifetimes in the safety state subsets and the mean values of their lifetimes in the particular safety states are defined. The multi-state system risk function and the moment of exceeding by the system the critical safety state are introduced. Applications of the proposed multistate system safety models to the evaluation and prediction of the safty characteristics of the consecutive “m out of n: F” is presented as well.

  1. Addressing firefighter safety around solar PV systems

    Energy Technology Data Exchange (ETDEWEB)

    Harris, B. [Sustainable Energy Technologies, Calgary, AB (Canada)


    The article discussed new considerations for installing photovoltaic (PV) systems that address the needs of fire service personnel. The presence of a PV system presents a multitude of dangers for firefighters, including electrical shock, the inhalation of toxic gases from being unable to cut a hole through the roof, falling debris and flying glass, and dead loading on a compromised structure and tripping on conduits. Mapping systems should be modified so that buildings with PV systems are identified for first responders, including firefighters who should learn that solar modules present an electrical hazard during the day but not at night; covering PV modules with foam or salvage covers may not shut the system down to a safe level; it takes a few moments for the power in PV modules to reduce to zero; and PV modules or conduit should never be cut, broke, chopped, or walked upon. The California Department of Forestry and Fire Protection recommends creating pathways and allowing easier access to the roof by setting the modules back from roof edges, creating a structurally sound pathway for firefighters to walk on and space to cut ventilation holes. However, the setback rule makes the economics of solar installation less viable for residential applications. The technological innovations aimed at addressing system safety all focus on limiting firefighter contact with live electrical components to within the extra-low-voltage (ELV) band. Some of the inverters on the market that support ELV system architecture were described. 1 fig.

  2. Examining the Relationship between Safety Management System Implementation and Safety Culture in Collegiate Flight Schools (United States)

    Robertson, Mike Fuller


    Safety Management Systems (SMS) are becoming the industry standard for safety management throughout the aviation industry. As the Federal Aviation Administration (FAA) continues to mandate SMS for different segments, the assessment of an organization's safety culture becomes more important. An SMS can facilitate the development of a strong…

  3. Model-based safety architecture framework for complex systems

    NARCIS (Netherlands)

    Schuitemaker, K.; Rajabali Nejad, Mohammadreza; Braakhuis, J.G.; Podofilini, Luca; Sudret, Bruno; Stojadinovic, Bozidar; Zio, Enrico; Kröger, Wolfgang


    The shift to transparency and rising need of the general public for safety, together with the increasing complexity and interdisciplinarity of modern safety-critical Systems of Systems (SoS) have resulted in a Model-Based Safety Architecture Framework (MBSAF) for capturing and sharing architectural

  4. Developing and maintaining national food safety control systems ...

    African Journals Online (AJOL)

    The establishment of effective food safety systems is pivotal to ensuring the safety of the national food supply as well as food products for regional and international trade. The development, structure and implementation of modern food safety systems have been driven over the years by a number of developments.

  5. The detector safety system for LHC experiments

    CERN Document Server

    Schmeling, Sascha; Lüders, S; Morpurgo, Giulio


    The Detector Safety System (DSS), currently being developed at CERN under the auspices of the Joint Controls Project (JCOP), will be responsible for assuring the protection of equipment for the four Large Hadron Collider (LHC)**1 experiments. Thus, the DSS will require a high degree of both availability and reliability. After evaluation of various possible solutions, a prototype is being built based on a redundant Siemens PLC**2 front-end, to which the safety- critical part of the DSS task is delegated. This is then supervised by a PVSS**3 SCADA**4 system via an OPC**5 server. The PLC front-end is capable of running autonomously and of automatically taking predefined protective actions whenever required. The supervisory layer provides the operator with a status display and with limited online reconfiguration capabilities. Configuration of the code running in the PLCs will be completely data driven via the contents of a "configuration database." Thus, the DSS can easily adapt to the different and constantly ev...

  6. Assessment of Safety Standards for Automotive Electronic Control Systems (United States)


    This report summarizes the results of a study that assessed and compared six industry and government safety standards relevant to the safety and reliability of automotive electronic control systems. These standards include ISO 26262 (Road Vehicles - ...

  7. Fire safety evaluation system for NASA office/laboratory buildings (United States)

    Nelson, H. E.


    A fire safety evaluation system for office/laboratory buildings is developed. The system is a life safety grading system. The system scores building construction, hazardous areas, vertical openings, sprinklers, detectors, alarms, interior finish, smoke control, exit systems, compartmentation, and emergency preparedness.

  8. Human factors systems approach to healthcare quality and patient safety (United States)

    Carayon, Pascale; Wetterneck, Tosha B.; Rivera-Rodriguez, A. Joy; Hundt, Ann Schoofs; Hoonakker, Peter; Holden, Richard; Gurses, Ayse P.


    Human factors systems approaches are critical for improving healthcare quality and patient safety. The SEIPS (Systems Engineering Initiative for Patient Safety) model of work system and patient safety is a human factors systems approach that has been successfully applied in healthcare research and practice. Several research and practical applications of the SEIPS model are described. Important implications of the SEIPS model for healthcare system and process redesign are highlighted. Principles for redesigning healthcare systems using the SEIPS model are described. Balancing the work system and encouraging the active and adaptive role of workers are key principles for improving healthcare quality and patient safety. PMID:23845724

  9. Role of systems safety in maintaining affordable safety in the 1980's

    Energy Technology Data Exchange (ETDEWEB)

    Hollister, H.; Trauth, C.A. Jr.


    Historically, the Department of Energy and its predecessors have used and supported the development of systems safety programs, practices, and principles, finding them by and large adequate, effective, and managerially efficient. Today, attempts are bing made to resolve increasingly complex environmental, safety, and health problems by turning to increasingly complex and detailed regulation as the primary governmental answer. It is increasingly doubtful that such an approach will provide management of these issues and problems that is either effective or efficient. Challenge is issued to those in systems safety to develop and apply systems safety principles and practices more broadly to total operational systems and not just to hardware and to environmental and health protection and not just to safety, so that the total universe of environmental, safety, and health can be managed effectively and efficiently with encouragement of innovation and creativity, using a relatively brief and concise, but adequate, regulatory base.

  10. 49 CFR 659.15 - System safety program standard. (United States)


    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE SAFETY OVERSIGHT Role of the..., policies, and roles and responsibilities for providing safety and security oversight of the rail transit... safety and security reviews. This section shall specify the role of the oversight agency in overseeing...

  11. Analysis of road safety management systems in Europe.

    NARCIS (Netherlands)

    Muhlrad, N. Vallet, G. Butler, I. Gitelman, V. Doveh, E. Dupont, E. Thomas, P. Talbot, R. Papadimitriou, E. Yannis, G. Persia, L. Giustiniani, G. Machata, K. & Bax, C.A.


    The objective of this paper is the analysis of road safety management in European countries and the identification of “good practice”. A road safety management investigation model was created, based on several “good practice” criteria. Road safety management systems have been thoroughly investigated

  12. Safety climate and culture: Integrating psychological and systems perspectives. (United States)

    Casey, Tristan; Griffin, Mark A; Flatau Harrison, Huw; Neal, Andrew


    Safety climate research has reached a mature stage of development, with a number of meta-analyses demonstrating the link between safety climate and safety outcomes. More recently, there has been interest from systems theorists in integrating the concept of safety culture and to a lesser extent, safety climate into systems-based models of organizational safety. Such models represent a theoretical and practical development of the safety climate concept by positioning climate as part of a dynamic work system in which perceptions of safety act to constrain and shape employee behavior. We propose safety climate and safety culture constitute part of the enabling capitals through which organizations build safety capability. We discuss how organizations can deploy different configurations of enabling capital to exert control over work systems and maintain safe and productive performance. We outline 4 key strategies through which organizations to reconcile the system control problems of promotion versus prevention, and stability versus flexibility. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  13. When learners surpass their models: the acquisition of American Sign Language from inconsistent input. (United States)

    Singleton, Jenny L; Newport, Elissa L


    The present study examines the impact of highly inconsistent input on language acquisition. The American deaf community provides a unique opportunity to observe children exposed to nonnative language models as their only linguistic input. This research is a detailed case study of one child acquiring his native language in such circumstances. It asks whether this child is capable of organizing a natural language out of input data that are not representative of certain natural language principles. Simon is a deaf child whose deaf parents both learned American Sign Language (ASL) after age 15. Simon's only ASL input is provided by his late-learner parents. The study examines Simon's performance at age 7 on an ASL morphology task, compared with eight children who have native signing parents, and also compared with Simon's own parents. The results show that Simon's production of ASL substantially surpasses that of his parents. Simon's parents, like other late learners of ASL, perform below adult native signing criteria, with many inconsistencies and errors in their use of ASL morphology. In contrast, Simon's performance is much more regular, and in fact on most ASL morphemes is equal to that of children exposed to a native signing model. The results thus indicate that Simon is capable of acquiring a regular and orderly morphological rule system for which his input provides only highly inconsistent and noisy data. In addition, the results provide some insight into the mechanisms by which such learning may occur. Although the ASL situation is rare, it reveals clues that may contribute to our understanding of the human capacity for language learning.

  14. Vehicle Safety Enhancement System: Sensing and Communication


    Huihuan Qian; Yongquan Chen; Yuandong Sun; Niansheng Liu; Ning Ding; Yangsheng Xu; Guoqing Xu; Yunjian Tang; Jingyu Yan


    With the substantial increase of vehicles on road, driving safety and transportation efficiency have become increasingly concerned focus from drivers, passengers, and governments. Wireless networks constructed by vehicles and infrastructures provide abundant information to share for the sake of both enhanced safety and network efficiency. This paper presents the systematic research to enhance the vehicle safety by wireless communication, in the aspects of information acquisition through vehic...

  15. Automated Safety Incident Surveillance and Tracking System (ASISTS) (United States)

    Department of Veterans Affairs — The Automated Safety Incident Surveillance and Tracking System (ASISTS) is a repository of Veterans Health Administration (VHA) employee accident data. Many types of...

  16. Design an optimum safety policy for personnel safety management - A system dynamic approach

    Energy Technology Data Exchange (ETDEWEB)

    Balaji, P. [The Glocal University, Mirzapur Pole, Delhi- Yamuntori Highway, Saharanpur 2470001 (India)


    Personnel safety management (PSM) ensures that employee's work conditions are healthy and safe by various proactive and reactive approaches. Nowadays it is a complex phenomenon because of increasing dynamic nature of organisations which results in an increase of accidents. An important part of accident prevention is to understand the existing system properly and make safety strategies for that system. System dynamics modelling appears to be an appropriate methodology to explore and make strategy for PSM. Many system dynamics models of industrial systems have been built entirely for specific host firms. This thesis illustrates an alternative approach. The generic system dynamics model of Personnel safety management was developed and tested in a host firm. The model was undergone various structural, behavioural and policy tests. The utility and effectiveness of model was further explored through modelling a safety scenario. In order to create effective safety policy under resource constraint, DOE (Design of experiment) was used. DOE uses classic designs, namely, fractional factorials and central composite designs. It used to make second order regression equation which serve as an objective function. That function was optimized under budget constraint and optimum value used for safety policy which shown greatest improvement in overall PSM. The outcome of this research indicates that personnel safety management model has the capability for acting as instruction tool to improve understanding of safety management and also as an aid to policy making.

  17. Design an optimum safety policy for personnel safety management - A system dynamic approach (United States)

    Balaji, P.


    Personnel safety management (PSM) ensures that employee's work conditions are healthy and safe by various proactive and reactive approaches. Nowadays it is a complex phenomenon because of increasing dynamic nature of organisations which results in an increase of accidents. An important part of accident prevention is to understand the existing system properly and make safety strategies for that system. System dynamics modelling appears to be an appropriate methodology to explore and make strategy for PSM. Many system dynamics models of industrial systems have been built entirely for specific host firms. This thesis illustrates an alternative approach. The generic system dynamics model of Personnel safety management was developed and tested in a host firm. The model was undergone various structural, behavioural and policy tests. The utility and effectiveness of model was further explored through modelling a safety scenario. In order to create effective safety policy under resource constraint, DOE (Design of experiment) was used. DOE uses classic designs, namely, fractional factorials and central composite designs. It used to make second order regression equation which serve as an objective function. That function was optimized under budget constraint and optimum value used for safety policy which shown greatest improvement in overall PSM. The outcome of this research indicates that personnel safety management model has the capability for acting as instruction tool to improve understanding of safety management and also as an aid to policy making.

  18. Managing Safety and Operations: The Effect of Joint Management System Practices on Safety and Operational Outcomes. (United States)

    Tompa, Emile; Robson, Lynda; Sarnocinska-Hart, Anna; Klassen, Robert; Shevchenko, Anton; Sharma, Sharvani; Hogg-Johnson, Sheilah; Amick, Benjamin C; Johnston, David A; Veltri, Anthony; Pagell, Mark


    The aim of this study was to determine whether management system practices directed at both occupational health and safety (OHS) and operations (joint management system [JMS] practices) result in better outcomes in both areas than in alternative practices. Separate regressions were estimated for OHS and operational outcomes using data from a survey along with administrative records on injuries and illnesses. Organizations with JMS practices had better operational and safety outcomes than organizations without these practices. They had similar OHS outcomes as those with operations-weak practices, and in some cases, better outcomes than organizations with safety-weak practices. They had similar operational outcomes as those with safety-weak practices, and better outcomes than those with operations-weak practices. Safety and operations appear complementary in organizations with JMS practices in that there is no penalty for either safety or operational outcomes.

  19. Safety Evalution of Cryptography Modules within Safety Related Control Systems for Railway Applications

    Directory of Open Access Journals (Sweden)

    Maria Franekova


    Full Text Available The paper deals with the problem of safety evaluation of cryptographic modules used within safety-related control system for applications with increasing safety integrity level. The requirements to cryptographic techniques in safety-related communication for railway application are describe. The mainly part is oriented to description of mathematical apparatus for an error probability of cryptography code with a safety code, used in an additional safety communication layer. The practical results are related with the quantitative evaluation of an average error probability of code word for Euroradio protocol recommended for communication in European Train Control System.

  20. System and safety studies of accelerator driven transmutation systems

    Energy Technology Data Exchange (ETDEWEB)

    Gudowski, W.; Wallenius, J.; Tucek, K.; Eriksson, Marcus; Carlsson, Johan; Seltborg, P.; Cetnar, J. [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Nuclear and Reactor Physics


    The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the department has been focused on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache). Moreover, during the reporting period the EU-project 'IABAT', co-ordinated by the department has been finished and 4 other projects have been initiated in the frame of the 5th European Framework Programme. Most of the research topics reported in this paper are referred to appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details.

  1. Food safety performance indicators to benchmark food safety output of food safety management systems

    NARCIS (Netherlands)

    Jacxsens, L.; Uyttendaele, M.; Devlieghere, F.; Rovira, J.; Oses Gomez, S.; Luning, P.A.


    There is a need to measure the food safety performance in the agri-food chain without performing actual microbiological analysis. A food safety performance diagnosis, based on seven indicators and corresponding assessment grids have been developed and validated in nine European food businesses.

  2. A concurrent diagnosis of microbiological food safety output and food safety management system performance: Cases from meat processing industries

    NARCIS (Netherlands)

    Luning, P.A.; Jacxsens, L.; Rovira, J.; Oses Gomez, S.; Uyttendaele, M.; Marcelis, W.J.


    Stakeholder requirements force companies to analyse their food safety management system (FSMS) performance to improve food safety. Performance is commonly analysed by checking compliance against preset requirements via audits/inspections, or actual food safety (FS) output is analysed by

  3. Research on the improvement of nuclear safety -Thermal hydraulic tests for reactor safety system-

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Moon Kee; Park, Choon Kyung; Yang, Sun Kyoo; Chun, Se Yung; Song, Chul Hwa; Jun, Hyung Kil; Jung, Heung Joon; Won, Soon Yun; Cho, Yung Roh; Min, Kyung Hoh; Jung, Jang Hwan; Jang, Suk Kyoo; Kim, Bok Deuk; Kim, Wooi Kyung; Huh, Jin; Kim, Sook Kwan; Moon, Sang Kee; Lee, Sang Il [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)


    The present research aims at the development of the thermal hydraulic verification test technology for the safety system of the conventional and advanced nuclear power plant and the development of the advanced thermal hydraulic measuring techniques. In this research, test facilities simulating the primary coolant system and safety system are being constructed for the design verification tests of the existing and advanced nuclear power plant. 97 figs, 14 tabs, 65 refs. (Author).

  4. System safety theory and human factors approach to patient safety for radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Abou, S.C. [Univ. of Minnesota, Mechanical and Industrial Engineering Dept., Duluth, Minnesota (United States)


    The research questions in this study while developing modern medical technology for safer applications of radiation therapy are - what medical and radiobiological effects and their quantitative models must be taken into account while defining the radiation risk. The uncertainty in the expression of these consequences for the delayed effects is one of the important problems the solution of which is necessary for radiation safety. The main principles of ensuring the radiation safety and the assessment of software technological risk developed on the basis of the intrinsic compatibility with safety systems theory, as an example, those which follow the concept of 'Inherent safety' are presented in this paper. (author)

  5. Towards predictive cardiovascular safety : a systems pharmacology approach

    NARCIS (Netherlands)

    Snelder, Nelleke


    Cardiovascular safety issues related to changes in blood pressure, arise frequently in drug development. In the thesis “Towards predictive cardiovascular safety – a systems pharmacology approach”, a system-specific model is described to quantify drug effects on the interrelationship between mean

  6. Software for the occupational health and safety integrated management system

    Energy Technology Data Exchange (ETDEWEB)

    Vătăsescu, Mihaela [University Politehnica Timisoara, Department of Engineering and Management, 5 Revolutiei street, 331128 Hunedoara (Romania)


    This paper intends to present the design and the production of a software for the Occupational Health and Safety Integrated Management System with the view to a rapid drawing up of the system documents in the field of occupational health and safety.

  7. Safety Characteristics in System Application Software for Human Rated Exploration (United States)

    Mango, E. J.


    NASA and its industry and international partners are embarking on a bold and inspiring development effort to design and build an exploration class space system. The space system is made up of the Orion system, the Space Launch System (SLS) and the Ground Systems Development and Operations (GSDO) system. All are highly coupled together and dependent on each other for the combined safety of the space system. A key area of system safety focus needs to be in the ground and flight application software system (GFAS). In the development, certification and operations of GFAS, there are a series of safety characteristics that define the approach to ensure mission success. This paper will explore and examine the safety characteristics of the GFAS development.

  8. 77 FR 55371 - System Safety Program (United States)


    ..., controlling, and continually assessing risk; and promotion of safety culture.'' Id. Under FAA's proposed... inclined toward the RSAC recommendation. However, FRA is in no way bound to follow the recommendation and...

  9. Frequency of target crashes for IntelliDrive safety systems (United States)


    This report estimates the frequency of different crash types that would potentially be addressed by various categories of Intelligent Transportation Systems as part of the IntelliDriveSM safety systems program. Crash types include light-vehicle crash...

  10. Development of Safety Grade Control Platforms for Safety I and C System Against Common Cause Failure

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Jong Gyun; Kim, Chang Hoi [KAERI, Daejeon (Korea, Republic of)


    Two diverse control platforms have been developed for application to safety I and C systems which have capability to mitigate CCFs under the project funded by the Korean Ministry of Trade, Industry and Energy. In this project Susan E and S develops the microprocessor based control platform named SPLC and Doosan Heavy Industry is in charge of developing the FPGA based control platform named DFLC-N. This paper describes the typical diversity strategies which can be implemented in safety I and C systems and introduces two safety grade control platforms being developed to improve the diversity of safety I and C systems. Two control platforms have been developed for application to safety I and C systems under the project funded by the Korean Ministry of Trade, Industry and Energy. In this project Susan E and S develops the microprocessor based control platform and Doosan Heavy Industry is in charge of developing the FPGA based control platform In this paper the typical diversity strategies implemented in safety I and C systems were described and the design concept of two safety grade platforms was introduced for mitigating the CCF vulnerabilities.

  11. Declarative Rule-based Safety for Robotic Perception Systems

    DEFF Research Database (Denmark)

    Mogensen, Johann Thor Ingibergsson; Kraft, Dirk; Schultz, Ulrik Pagh


    Mobile robots are used across many domains from personal care to agriculture. Working in dynamic open-ended environments puts high constraints on the robot perception system, which is critical for the safety of the system as a whole. To achieve the required safety levels the perception system needs....... The language allows developers to increase trustworthiness in the robot perception system, which we argue would increase compliance with safety standards. We demonstrate the usage of the language to improve reliability in a perception pipeline and evaluate it against manually written rules on embedded hardware...

  12. Tank waste remediation system nuclear criticality safety program management review

    Energy Technology Data Exchange (ETDEWEB)



    This document provides the results of an internal management review of the Tank Waste Remediation System (TWRS) criticality safety program, performed in advance of the DOE/RL assessment for closure of the TWRS Nuclear Criticality Safety Issue, March 1994. Resolution of the safety issue was identified as Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) Milestone M-40-12, due September 1999.

  13. Simulation of data safety components for corporative systems (United States)

    Yaremko, Svetlana A.; Kuzmina, Elena M.; Savchuk, Tamara O.; Krivonosov, Valeriy E.; Smolarz, Andrzej; Arman, Abenov; Smailova, Saule; Kalizhanova, Aliya


    The article deals with research of designing data safety components for corporations by means of mathematical simulations and modern information technologies. Simulation of threats ranks has been done which is based on definite values of data components. The rules of safety policy for corporative information systems have been presented. The ways of realization of safety policy rules have been proposed on the basis of taken conditions and appropriate class of valuable data protection.

  14. Development of the Advanced Nuclear Safety Information Management (ANSIM) System

    Energy Technology Data Exchange (ETDEWEB)

    Sohn, Jae Min; Ko, Young Cheol; Song, Tai Gil [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    Korea has become a technically independent nuclear country and has grown into an exporter of nuclear technologies. Thus, nuclear facilities are increasing in significance at KAERI (Korea Atomic Energy Research Institute), and it is time to address the nuclear safety. The importance of nuclear safety cannot be overemphasized. Therefore, a management system is needed urgently to manage the safety of nuclear facilities and to enhance the efficiency of nuclear information. We have established ISP (Information Strategy Planning) for the Integrated Information System of nuclear facility and safety management. The purpose of this paper is to develop a management system for nuclear safety. Therefore, we developed the Advanced Nuclear Safety Information Management system (hereinafter referred to as the 'ANSIM system'). The ANSIM system has been designed and implemented to computerize nuclear safety information for standardization, integration, and sharing in real-time. Figure 1 shows the main home page of the ANSIM system. In this paper, we describe the design requirements, contents, configurations, and utilizations of the ANSIM system

  15. METIS: Dependable Cooperative Systems for Public Safety

    NARCIS (Netherlands)

    Hendriks, A.J.; Laar, P.J.L.J. van de


    Much, if not most, information needed to assess a crisis situation originates these days from cooperative sources such as the Internet and social networks. Public safety authorities face the challenge to compile this information of uncertain origin and quality in their situation understanding and

  16. The PIANC Safety Factor System for Breakwaters

    DEFF Research Database (Denmark)

    Burcharth, H. F.


    The paper presents a summary of the recommendations for implementation of safety in breakwater designs given by the PIANC PTC IT Working Group No 12 on Analysis of Rubble Mound Breakwaters with Vertical and Inclined Concrete Walls. The working groups developed for the most important failure modes...

  17. Communication and Networking Techniques for Traffic Safety Systems


    Chisalita, Ioan


    Accident statistics indicate that every year a significant number of casualties and extensive property losses occur due to traffic accidents. Consequently, efforts are directed towards developing passive and active safety systems that help reduce the severity of crashes, or prevent vehicles from colliding with one another. To develop these systems, technologies such as sensor systems, computer vision and vehicular communication have been proposed. Safety vehicular communication is defined as ...

  18. A management system integrating radiation protection and safety supporting safety culture in the hospital. (United States)

    Almén, A; Lundh, C


    Quality assurance has been identified as an important part of radiation protection and safety for a considerable time period. A rational expansion and improvement of quality assurance is to integrate radiation protection and safety in a management system. The aim of this study was to explore factors influencing the implementing strategy when introducing a management system including radiation protection and safety in hospitals and to outline benefits of such a system. The main experience from developing a management system is that it is possible to create a vast number of common policies and routines for the whole hospital, resulting in a cost-efficient system. One of the key benefits is the involvement of management at all levels, including the hospital director. Furthermore, a transparent system will involve staff throughout the organisation as well. A management system supports a common view on what should be done, who should do it and how the activities are reviewed. An integrated management system for radiation protection and safety includes key elements supporting a safety culture. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email:

  19. Occupational Safety and Health Systems: A Three-Country Comparison. (United States)

    Singleton, W. T.


    This article compares the occupational safety and health systems of Switzerland, the United Kingdom, and the United States, looking at the origins of their legislation and its effects on occupational safety and health, with a view to determining what lessons may emerge, particularly for developing countries. (Author/SSH)

  20. Approaches to construction of systems of safety management in airlines

    Directory of Open Access Journals (Sweden)


    Full Text Available The article presents three approaches of building a safety management system (SMS in airlines in the framework of implementation of ICAO SARPs that apply methods of risk assessment based on use of operational activity of airline taking into account existing and implementing "protections" or "safety barriers".

  1. Fasten seat belts: Do car safety systems cause positive externalities?


    Michael Berlemann; Andreas Matthes


    Although traffic safety belongs to the quite intensively regulated sectors, there has been little discussion about the adequacy of the arguments underlying these regulations. We argue that passive and active car safety systems might cause positive externalities for other traffic participants and present empirical evidence in favour of this hypothesis.

  2. Development of a Comprehensive Database System for Safety Analyst

    National Research Council Canada - National Science Library

    Paz, Alexander; Veeramisti, Naveen; Khanal, Indira; Baker, Justin; de la Fuente-Mella, Hanns


    ... not widely used due to a number of challenges as described in this paper. As part of this study, a comprehensive database system and tools to provide data to multiple traffic safety applications, with a focus on Safety Analyst, were developed...

  3. Development of a Comprehensive Database System for Safety Analyst. (United States)

    Paz, Alexander; Veeramisti, Naveen; Khanal, Indira; Baker, Justin; de la Fuente-Mella, Hanns


    This study addressed barriers associated with the use of Safety Analyst, a state-of-the-art tool that has been developed to assist during the entire Traffic Safety Management process but that is not widely used due to a number of challenges as described in this paper. As part of this study, a comprehensive database system and tools to provide data to multiple traffic safety applications, with a focus on Safety Analyst, were developed. A number of data management tools were developed to extract, collect, transform, integrate, and load the data. The system includes consistency-checking capabilities to ensure the adequate insertion and update of data into the database. This system focused on data from roadways, ramps, intersections, and traffic characteristics for Safety Analyst. To test the proposed system and tools, data from Clark County, which is the largest county in Nevada and includes the cities of Las Vegas, Henderson, Boulder City, and North Las Vegas, was used. The database and Safety Analyst together help identify the sites with the potential for safety improvements. Specifically, this study examined the results from two case studies. The first case study, which identified sites having a potential for safety improvements with respect to fatal and all injury crashes, included all roadway elements and used default and calibrated Safety Performance Functions (SPFs). The second case study identified sites having a potential for safety improvements with respect to fatal and all injury crashes, specifically regarding intersections; it used default and calibrated SPFs as well. Conclusions were developed for the calibration of safety performance functions and the classification of site subtypes. Guidelines were provided about the selection of a particular network screening type or performance measure for network screening.

  4. The Danish patient safety experience: the Act on Patient Safety in the Danish Health care system

    DEFF Research Database (Denmark)

    Lundgaard, Mette; Rabøl, Louise; Jensen, Elisabeth Agnete Brøgger


    This paper describes the process that lead to the passing of the Act for Patient Safety in the Danisk health care sytem, the contents of the act and how the act is used in the Danish health care system. The act obligates frontline health care personnel to report adverse events, hospital owners...... to act on the reports and the National Board of Health to commuicate the learning nationally. The act protects health care providers from sanctions as a result of reporting. In January 2004, the Act on Patient Safety in the Danish health care system was put into force. In the first twelve months 5740...... adverse events were reported. the reports were analyzed locally (hospital and region), anonymized ad then sent to the National Board af Health. The Act on Patient Safety has driven the work with patient safety forward but there is room for improvement. Continuous and improved feedback from all parts...

  5. System safety based on a coordinated principle-based theme

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, J.A.


    In this paper, the authors demonstrate a logical progression for the identification of assets, threats, vulnerabilities, and protective measures, based on a structured approach that incorporates the results of the previous paper. The authors utilize a logical structure for identifying the constituents of the problem, derive appropriate applicable principles, and demonstrate a technique for incorporating the principles into a coordinated safety theme. They also show how to qualitatively assess such generally non-quantifiable items such as safety-component and safety-system response to severe abnormal environments. An illustrative example is followed step-by-step through to a safety system design approach and a safety assessment approach. The general approach is illustrated here through an example, generally representing a test rocket launch scenario, where the concern is the potential for loss of life.

  6. Analysis of Aviation Safety Reporting System Incident Data Associated With the Technical Challenges of the Vehicle Systems Safety Technology Project (United States)

    Withrow, Colleen A.; Reveley, Mary S.


    This analysis was conducted to support the Vehicle Systems Safety Technology (VSST) Project of the Aviation Safety Program (AVsP) milestone VSST4.2.1.01, "Identification of VSST-Related Trends." In particular, this is a review of incident data from the NASA Aviation Safety Reporting System (ASRS). The following three VSST-related technical challenges (TCs) were the focus of the incidents searched in the ASRS database: (1) Vechicle health assurance, (2) Effective crew-system interactions and decisions in all conditions; and (3) Aircraft loss of control prevention, mitigation, and recovery.

  7. Software reliability and safety in nuclear reactor protection systems

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence, J.D. [Lawrence Livermore National Lab., CA (United States)


    Planning the development, use and regulation of computer systems in nuclear reactor protection systems in such a way as to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Computer Safety and Reliability Group, Lawrence Livermore that investigates different aspects of computer software in reactor National Laboratory, that investigates different aspects of computer software in reactor protection systems. There are two central themes in the report, First, software considerations cannot be fully understood in isolation from computer hardware and application considerations. Second, the process of engineering reliability and safety into a computer system requires activities to be carried out throughout the software life cycle. The report discusses the many activities that can be carried out during the software life cycle to improve the safety and reliability of the resulting product. The viewpoint is primarily that of the assessor, or auditor.

  8. Analyzing Software Errors in Safety-Critical Embedded Systems (United States)

    Lutz, Robyn R.


    This paper analyzes the root causes of safty-related software faults identified as potentially hazardous to the system are distributed somewhat differently over the set of possible error causes than non-safety-related software faults.

  9. Automated Flight Safety Inference Engine (AFSIE) System Project (United States)

    National Aeronautics and Space Administration — We propose to develop an innovative Autonomous Flight Safety Inference Engine (AFSIE) system to autonomously and reliably terminate the flight of an errant launch...

  10. The mobility and safety of walk-and-ride systems. (United States)


    In this project we investigate the effect of traffic calming measures, such as crosswalks and sidewalks on the overall cost and safety of a multimodal transportation network system design. Our design problem includes auto, transit, and walking as mod...

  11. 33 CFR 147.847 - Safety Zone; BW PIONEER Floating Production, Storage, and Offloading System Safety Zone. (United States)


    ... Production, Storage, and Offloading System Safety Zone. 147.847 Section 147.847 Navigation and Navigable... ZONES § 147.847 Safety Zone; BW PIONEER Floating Production, Storage, and Offloading System Safety Zone. (a) Description. The BW PIONEER, a Floating Production, Storage and Offloading (FPSO) system, is in...

  12. What is Clinical Safety in Electronic Health Care Record Systems? (United States)

    Davies, George

    There is mounting public awareness of an increasing number of adverse clinical incidents within the National Health Service (NHS), but at the same time, large health care projects like the National Programme for IT (NPFIT) are claiming that safer care is one of the benefits of the project and that health software systems in particular have the potential to reduce the likelihood of accidental or unintentional harm to patients. This paper outlines the approach to clinical safety management taken by CSC, a major supplier to NPFIT; discusses acceptable levels of risk and clinical safety as an end-to-end concept; and touches on the future for clinical safety in health systems software.

  13. Simplified safety and containment systems for the iris reactor

    Energy Technology Data Exchange (ETDEWEB)

    Conway, L.E. [Westinghouse Electric Co., Pittsburgh, PA (United States); Lombardi, C.; Ricotti, M.; Oriani, L. [Polytechnic of Milan, Dept. of Nuclear Engineering, Milan (Italy)


    The IRIS (International Reactor Innovative and Secure) is a 100 - 300 MW modular type pressurized water reactor supported by the U.S. DOE NERI Program. IRIS features a long-life core to provide proliferation resistance and to reduce the volume of spent fuel, as well as reduce maintenance requirements. IRIS utilizes an integral reactor vessel that contains all major primary system components. This integral reactor vessel makes it possible to reduce containment size; making the IRIS more cost competitive. IRIS is being designed to enhance reactor safety, and therefore a key aspect of the IRIS program is the development of the safety and containment systems. These systems are being designed to maximize containment integrity, prevent core uncover following postulated accidents, minimize the probability and consequences of severe accidents, and provide a significant simplification over current safety system designs. The design of the IRIS containment and safety systems has been identified and preliminary analyses have been completed. The IRIS safety concept employs some unique features that minimize the consequences of postulated design basis events. This paper will provide a description of the containment design and safety systems, and will summarize the analysis results. (author)

  14. Formal methods in the development of safety critical software systems

    Energy Technology Data Exchange (ETDEWEB)

    Williams, L.G. [Software Engineering Research, Boulder, CO (United States)


    As the use of computers in critical control systems such as aircraft controls, medical instruments, defense systems, missile controls, and nuclear power plants has increased, concern for the safety of those systems has also grown. Much of this concern has focused on the software component of those computer-based systems. This is primarily due to historical experience with software systems that often exhibit larger numbers of errors than their hardware counterparts and the fact that the consequences of a software error may endanger human life, property, or the environment. A number of different techniques have been used to address the issue of software safety. Some are standard software engineering techniques aimed at reducing the number of faults in a software protect, such as reviews and walkthroughs. Others, including fault tree analysis, are based on identifying and reducing hazards. This report examines the role of one such technique, formal methods, in the development of software for safety critical systems. The use of formal methods to increase the safety of software systems is based on their role in reducing the possibility of software errors that could lead to hazards. The use of formal methods in the development of software systems is controversial. Proponents claim that the use of formal methods can eliminate errors from the software development process, and produce programs that are probably correct. Opponents claim that they are difficult to learn and that their use increases development costs unacceptably. This report discusses the potential of formal methods for reducing failures in safety critical software systems.

  15. Passive modular gas safety system for a reactor

    Energy Technology Data Exchange (ETDEWEB)

    Abalin, S.S.; Isaev, I.F.; Kulakov, A.A.; Sivokon, V.P.; Udovenko, A.N.; Ionaitis, R.R.


    Reactor safety systems have developed gradually. Today in particular, auxiliary systems are being developed which are based on nontraditional operational concepts, by using gaseous neutron absorbers. The Scientific-Research and Design Institute of Power Technology (NIKIET) and the Institute of Nuclear Reactors, Kurchatov Institute Reactor Science Center (RNTs), have done preliminary development and experimental verification of separate elements of this system, in which helium is used as the absorber. This article presents a rapid passive safety system based on gaseous absorber, which is made as autonomous modules as the final stage of reactor safety. Its effectiveness is discussed by using an RBMK reactor as an example. As opposed to traditional active, systems, it does not require a functioning power supply and information signals from outside the reactors system, which makes it stable against unsanctioned actions by personnel, the influence of other systems, and also outside actions (sabotage and natural calamities which could destroy the the nuclear power plant structure). Because the gas safety system can operate instantaneously (0.1-0.3 sec), in principle, it can shut down the reactor even with fast-neutron runaway, where traditional safety systems are ineffective.

  16. Evaluating software for safety systems in nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence, J.D.; Persons, W.L.; Preckshot, G.G. [Lawrence Livermore National Lab., CA (United States); Gallagher, J. [Nuclear Regulatory Commission, Washington, DC (United States). Office of Nuclear Reactor Regulation


    In 1991, LLNL was asked by the NRC to provide technical assistance in various aspects of computer technology that apply to computer-based reactor protection systems. This has involved the review of safety aspects of new reactor designs and the provision of technical advice on the use of computer technology in systems important to reactor safety. The latter includes determining and documenting state-of-the-art subjects that require regulatory involvement by the NRC because of their importance in the development and implementation of digital computer safety systems. These subjects include data communications, formal methods, testing, software hazards analysis, verification and validation, computer security, performance, software complexity and others. One topic software reliability and safety is the subject of this paper.

  17. Systems Analysis of NASA Aviation Safety Program: Final Report (United States)

    Jones, Sharon M.; Reveley, Mary S.; Withrow, Colleen A.; Evans, Joni K.; Barr, Lawrence; Leone, Karen


    A three-month study (February to April 2010) of the NASA Aviation Safety (AvSafe) program was conducted. This study comprised three components: (1) a statistical analysis of currently available civilian subsonic aircraft data from the National Transportation Safety Board (NTSB), the Federal Aviation Administration (FAA), and the Aviation Safety Information Analysis and Sharing (ASIAS) system to identify any significant or overlooked aviation safety issues; (2) a high-level qualitative identification of future safety risks, with an assessment of the potential impact of the NASA AvSafe research on the National Airspace System (NAS) based on these risks; and (3) a detailed, top-down analysis of the NASA AvSafe program using an established and peer-reviewed systems analysis methodology. The statistical analysis identified the top aviation "tall poles" based on NTSB accident and FAA incident data from 1997 to 2006. A separate examination of medical helicopter accidents in the United States was also conducted. Multiple external sources were used to develop a compilation of ten "tall poles" in future safety issues/risks. The top-down analysis of the AvSafe was conducted by using a modification of the Gibson methodology. Of the 17 challenging safety issues that were identified, 11 were directly addressed by the AvSafe program research portfolio.

  18. Development of a Safety Assessment Information System for the Management of Periodic Safety Assessment Activities

    Energy Technology Data Exchange (ETDEWEB)

    Song, Tae Young [Nuclear Engineering and Technology Institute, Daejeon (Korea, Republic of)


    At present, the 10-year Periodic Safety Review(PSR) has been performing to confirm all the aspects of safety issues for all the operating plants in compliance with domestic nuclear law of article 23, subarticle 3. For each plant, in addition, Probabilistic Safety Assessment(PSA) and Severe Accident Management Guideline(SAMG) are being implemented and revised periodically to reflect the latest safety level according to principle fulfillment of severe accident policy statement. The assessment reports, as one of outcomes from these activities, are submitted into and reviewed by domestic regulatory body. During reviewing (in-office duty) and licensing (regulatory duty) process, a large number of outcomes of which most are the formal technical reports and licensing materials, are inevitably produced. Moreover, repeated review process over the plants can make them accumulated and produce a variety of documents additionally. This circumstance motivates to develop effective tool or system for the management of these reports and related technical documents for the future use in licensing process and for subsequent plant assessments. This paper presents the development status of Safety Assessment Information System(SAIS) which manages safety-related documents of PSR, PSA and SAMG for practical use for experienced engineers in charge of these areas.

  19. Stakeholder Safety in Information Systems Research

    Directory of Open Access Journals (Sweden)

    R.H. Barbour


    Full Text Available Information Communication Technology (ICT researchers adapt and use tools from reference and cognate disciplines. This application of existing tools outside the context of their development has implications beyond the immediate problem context. ICT researchers have access to a wide variety of data sources including newer ones, such as the Internet, that may bring unexpected outcomes. ICT research can impact on researchers, their institutions and the researched in unexpected ways. People so affected are the stakeholders in ICT research activities. Reputations, welfare and property may be put at risk by unplanned events described in this paper. Legal aspects of ICT research are broadly identified and linked to the tort of negligence. The Social Research Association’s Code for researcher safety is described and its application extended to include the Internet as a potential data source. A common set of underlying ethical principles is identified suggesting that the ICT researcher can refine particular research protocols for specific social contexts.

  20. Risk and safety analysis of nuclear systems

    National Research Council Canada - National Science Library

    Lee, John C; McCormick, Norman J


    ...), and failure modes of systems. All of this material is general enough that it could be used in non-nuclear applications, although there is an emphasis placed on the analysis of nuclear systems...

  1. Editorial: emerging issues in sociotechnical systems thinking and workplace safety. (United States)

    Noy, Y Ian; Hettinger, Lawrence J; Dainoff, Marvin J; Carayon, Pascale; Leveson, Nancy G; Robertson, Michelle M; Courtney, Theodore K


    The burden of on-the-job accidents and fatalities and the harm of associated human suffering continue to present an important challenge for safety researchers and practitioners. While significant improvements have been achieved in recent decades, the workplace accident rate remains unacceptably high. This has spurred interest in the development of novel research approaches, with particular interest in the systemic influences of social/organisational and technological factors. In response, the Hopkinton Conference on Sociotechnical Systems and Safety was organised to assess the current state of knowledge in the area and to identify research priorities. Over the course of several months prior to the conference, leading international experts drafted collaborative, state-of-the-art reviews covering various aspects of sociotechnical systems and safety. These papers, presented in this special issue, cover topics ranging from the identification of key concepts and definitions to sociotechnical characteristics of safe and unsafe organisations. This paper provides an overview of the conference and introduces key themes and topics. Sociotechnical approaches to workplace safety are intended to draw practitioners' attention to the critical influence that systemic social/organisational and technological factors exert on safety-relevant outcomes. This paper introduces major themes addressed in the Hopkinton Conference within the context of current workplace safety research and practice challenges.

  2. Digital Signal Processing for In-Vehicle Systems and Safety

    CERN Document Server

    Boyraz, Pinar; Takeda, Kazuya; Abut, Hüseyin


    Compiled from papers of the 4th Biennial Workshop on DSP (Digital Signal Processing) for In-Vehicle Systems and Safety this edited collection features world-class experts from diverse fields focusing on integrating smart in-vehicle systems with human factors to enhance safety in automobiles. Digital Signal Processing for In-Vehicle Systems and Safety presents new approaches on how to reduce driver inattention and prevent road accidents. The material addresses DSP technologies in adaptive automobiles, in-vehicle dialogue systems, human machine interfaces, video and audio processing, and in-vehicle speech systems. The volume also features: Recent advances in Smart-Car technology – vehicles that take into account and conform to the driver Driver-vehicle interfaces that take into account the driving task and cognitive load of the driver Best practices for In-Vehicle Corpus Development and distribution Information on multi-sensor analysis and fusion techniques for robust driver monitoring and driver recognition ...

  3. Engineering systems reliability, safety, and maintenance an integrated approach

    CERN Document Server

    Dhillon, B S


    Today, engineering systems are an important element of the world economy and each year billions of dollars are spent to develop, manufacture, operate, and maintain various types of engineering systems around the globe. Many of these systems are highly sophisticated and contain millions of parts. For example, a Boeing jumbo 747 is made up of approximately 4.5 million parts including fasteners. Needless to say, reliability, safety, and maintenance of systems such as this have become more important than ever before.  Global competition and other factors are forcing manufacturers to produce highly reliable, safe, and maintainable engineering products. Therefore, there is a definite need for the reliability, safety, and maintenance professionals to work closely during design and other phases. Engineering Systems Reliability, Safety, and Maintenance: An Integrated Approach eliminates the need to consult many different and diverse sources in the hunt for the information required to design better engineering syste...

  4. Epistemic Questions and Answers for Software System Safety (United States)

    Holloway, C. M.; Johnson, Chris W.


    System safety is primarily concerned with epistemic questions, that is, questions concerning knowledge and the degree of confidence that can be placed in that knowledge. For systems with which human experience is long, such as roads, bridges, and mechanical devices, knowledge about what is required to make the systems safe is deep and detailed. High confidence can be placed in the validity of that knowledge. For other systems, however, with which human experience is comparatively short, such as those that rely in part or in whole on software, knowledge about what is required to ensure safety tends to be shallow and general. The confidence that can be placed in the validity of that knowledge is consequently low. In a previous paper, we enumerated a collection of foundational epistemic questions concerning software system safety. In this paper, we review and refine the questions, discuss some difficulties that attend to answering the questions today, and speculate on possible research to improve the situation.

  5. Failure and factors of safety in piping system design

    Energy Technology Data Exchange (ETDEWEB)

    Antaki, G.A.


    An important body of test and performance data on the behavior of piping systems has led to an ongoing reassessment of the code stress allowables and their safety margin. The codes stress allowables, and their factors of safety, are developed from limits on the incipient yield (for ductile materials), or incipient rupture (for brittle materials), of a test specimen loaded in simple tension. In this paper, we examine the failure theories introduced in the B31 and ASME III codes for piping and their inherent approximations compared to textbook failure theories. We summarize the evolution of factors of safety in ASME and B31 and point out that, for piping systems, it is appropriate to reconsider the concept and definition of factors of safety.

  6. Failure and factors of safety in piping system design

    Energy Technology Data Exchange (ETDEWEB)

    Antaki, G.A.


    An important body of test and performance data on the behavior of piping systems has led to an ongoing reassessment of the code stress allowables and their safety margin. The codes stress allowables, and their factors of safety, are developed from limits on the incipient yield (for ductile materials), or incipient rupture (for brittle materials), of a test specimen loaded in simple tension. In this paper, we examine the failure theories introduced in the B31 and ASME III codes for piping and their inherent approximations compared to textbook failure theories. We summarize the evolution of factors of safety in ASME and B31 and point out that, for piping systems, it is appropriate to reconsider the concept and definition of factors of safety.

  7. Safety design integrated in the building delivery system

    DEFF Research Database (Denmark)

    Jørgensen, Kirsten


    In construction, it is important to view safety and health as an integrated part of the way that “designers” are working. The designers cowers architects, constructors, engineers and others who carry out their consulting services in the design phase of a construction project. The philosophy...... is simple, if the demands for safety and health are incorporated early on in the solving of a building assignment, then it becomes much easier to organise the executing phase in a responsible manner safety-wise. But, the problem is that very few of the designers have knowledge or experience of how to do so....... The purpose of this article is to demonstrate how safety and health can be integrated in the design phases integrated in the management delivery systems within construction, The method for the research was to go through the building delivery system step by step and create a normative description of what, when...

  8. Intelligent Transport Systems (ITS) and road safety.

    NARCIS (Netherlands)


    Many developments are taking place in the area of Intelligent Transport Systems (ITS) for traffic purposes. Many of the current ITS applications are mainly aimed at increasing comfort while driving and at improving accessibility. In addition, systems like the alcolock and the seatbelt lock are being

  9. Proceedings of the Digital Systems Reliability and Nuclear Safety Workshop

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, D. R.; Cuthill, B. B.; Ippolito, L. M. [National Inst. of Standards and Technology, Gaithersburg, MD (United States); Beltracchi, L. [Nuclear Regulatory Commission, Washington, DC (United States) ed.


    The United States Nuclear Regulatory Commission (NRC), in cooperation with the National Institute of Standards and Technology conducted the.Digital Systems Reliability and Nuclear Safety Workshop on September 13--14, 1993, in Rockville, Maryland. The workshop provided a forum for the exchange of information among experts within the nuclear industry, experts from other industries, regulators and academia. The information presented at this workshop provided in-depth exposure of the NRC staff and the nuclear industry to digital systems design safety issues and also provided feedback to the NRC from outside experts regarding identified safety issues, proposed regulatory positions, and intended research associated with the use of digital systems in nuclear power plants. Technical presentations provided insights on areas where current software engineering practices may be inadequate for safety-critical systems, on potential solutions for development issues, and on methods for reducing risk in safety-critical systems. This report contains an analysis of results of the workshop, the papers presented panel presentations, and summaries of, discussions at this workshop. The individual papers have been cataloged separately.

  10. A fundamental study for safety in advanced PWR systems

    Energy Technology Data Exchange (ETDEWEB)

    Park, Goon Cherl; Kang, C. S.; Lee, E. C.; Kim, S. N.; Lee, J. S.; Kim, M. H.; Chae, W. S.; Kim, M. H.; Lee, D. H.; No, S. T.; Jeon, G. D.; Lee, T. H.; Kim, B. S.; Park, H. J.; Yoon, J. I.; Kim, J. H.; Jeon, J. H.; Jang, W. H.; Sa, Y. C.; Lee, H. W.; Kim, S. J.; Kim, J. W.; Kim, Y. H.; Lee, S. W.; Yang, C. G.; Kim, Y. S.; Ha, J. B.; Son, M. S.; An, Y. C.; Bae, S. W. [Seoul National University, Seoul (Korea, Republic of)


    For the development of integral type small and medium reactor which is remarkably safer than existing plants, the operability of passive safety systems should be studied and its applicability to the integral type reactor should be evaluated. The purposes of this study are to evaluate the characteristics of various passive safety systems and provide the proper data for the future design with performing experiments and developing analytical methodology. Thus in this study, the following techniques for small reactors and passive safety systems subject to this study are evaluated and a part of basic experiments and numerical works necessary to the experiments were performed, First, heat pipes used in containment vessel which removes hear by passive mechanism during accidents, second, natural circulation characteristics for the passive safety analysis of integrated reactor, third, heat evaluation of the effective function of hydraulic valve in passive decay heat removal systems, fifth, the determination of the improved source term for the integral reactor, and the last, passive containment cooling system, which is the first step in the analysis of the integrated safety and the environmental impacts of nuclear power plant. 184 refs., 49 tabs., 188 figs. (author)

  11. Information communications technologies that surpass the global communications network. Sekai tsushinmo o koeru joho tsushin gijutsu

    Energy Technology Data Exchange (ETDEWEB)


    Development of information communications technologies that surpass the global communications network is being pushed forward in order to establish the global village that McLuhan foretold in 1964. Effects of hybrid intensification with the intensification of communications technologies and computer technologies have become evident as facsimiles, automated teller machines of banks, home videos, automatic response telephones with synthetic voices, compact disks, portable telephones, video games and high-definition televisions were developed and put to use in a wide range. Intensification and integration of computer technologies and communications technologies has every possibility, but it also has a peculiar aspect of lacking guiding principles. Uncertain factors of the values of informations in the market are ever increasing, and their true values are yet to be found. Anyhow, it is a long way to the goal of the global village.

  12. Successful treatment of a giant pediatric fusiform basilar trunk aneurysm with surpass flow diverter. (United States)

    Kan, Peter; Mokin, Maxim; Puri, Ajit S; Wakhloo, Ajay K


    Fusiform aneurysms present a unique challenge to traditional microsurgical and endovascular treatment because of the lack of a discernible neck and the involvement of parent vessel. Flow diversion has increasingly become the treatment of choice for fusiform aneurysms in the anterior circulation, but its results in the posterior circulation are variable. We report successful treatment of a giant fusiform upper basilar trunk aneurysm with the Surpass flow diverter in an adolescent, and discuss the potential advantages of this emerging technology in the treatment of fusiform posterior circulation aneurysms. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to

  13. Driver monitoring system for automotive safety (United States)

    Lörincz, A. E.; Risteiu, M. N.; Ionica, A.; Leba, M.


    The lifestyle of a person is a very active one from all points of view. He travels great distance every day, with car or on foot. Tiredness and stress is found in every person. These can cause major problems when driving up and driving in small or big distances by car. A system developed to prevent the dangers we are prone to in these situations is very useful. System that can be used and implemented both in the production of current cars and the use of those not equipped with this system.

  14. Patient Safety Learning Systems: A Systematic Review and Qualitative Synthesis. (United States)


    A patient safety learning system (sometimes called a critical incident reporting system) refers to structured reporting, collation, and analysis of critical incidents. To inform a provincial working group's recommendations for an Ontario Patient Safety Event Learning System, a systematic review was undertaken to determine design features that would optimize its adoption into the health care system and would inform implementation strategies. The objective of this review was to address two research questions: (a) what are the barriers to and facilitators of successful adoption of a patient safety learning system reported by health professionals and (b) what design components maximize successful adoption and implementation? To answer the first question, we used a published systematic review. To answer the second question, we used scoping study methodology. Common barriers reported in the literature by health care professionals included fear of blame, legal penalties, the perception that incident reporting does not improve patient safety, lack of organizational support, inadequate feedback, lack of knowledge about incident reporting systems, and lack of understanding about what constitutes an error. Common facilitators included a non-accusatory environment, the perception that incident reporting improves safety, clarification of the route of reporting and of how the system uses reports, enhanced feedback, role models (such as managers) using and promoting reporting, legislated protection of those who report, ability to report anonymously, education and training opportunities, and clear guidelines on what to report. Components of a patient safety learning system that increased successful adoption and implementation were emphasis on a blame-free culture that encourages reporting and learning, clear guidelines on how and what to report, making sure the system is user-friendly, organizational development support for data analysis to generate meaningful learning outcomes

  15. New reactor technology: safety improvements in nuclear power systems. (United States)

    Corradini, M L


    Almost 450 nuclear power plants are currently operating throughout the world and supplying about 17% of the world's electricity. These plants perform safely, reliably, and have no free-release of byproducts to the environment. Given the current rate of growth in electricity demand and the ever growing concerns for the environment, nuclear power can only satisfy the need for electricity and other energy-intensive products if it can demonstrate (1) enhanced safety and system reliability, (2) minimal environmental impact via sustainable system designs, and (3) competitive economics. The U.S. Department of Energy with the international community has begun research on the next generation of nuclear energy systems that can be made available to the market by 2030 or earlier, and that can offer significant advances toward these challenging goals; in particular, six candidate reactor system designs have been identified. These future nuclear power systems will require advances in materials, reactor physics, as well as thermal-hydraulics to realize their full potential. However, all of these designs must demonstrate enhanced safety above and beyond current light water reactor systems if the next generation of nuclear power plants is to grow in number far beyond the current population. This paper reviews the advanced Generation-IV reactor systems and the key safety phenomena that must be considered to guarantee that enhanced safety can be assured in future nuclear reactor systems.

  16. Safety restraint systems in heavy truck rollover scenarios

    NARCIS (Netherlands)

    Slaats, P.M.A.; Coo, P.J.A. de


    Safety restraint systems have been widely applied in the passenger car industry. The heavy truck industry has followed along, integrating the seat belts in the seat system. The effectiveness of seat belts, in particular in rollover scenarios, was studied for a number of heavy truck rollover

  17. Continuous restraint control systems: safety improvement for various occupants

    NARCIS (Netherlands)

    Laan, E. van der; Jager, B. de; Veldpaus, F.; Steinbuch, M.; Nunen, E. van; Willemsen, D.


    Occupant safety can be significantly improved by continuous restraint control systems. These restraint systems adjust their configuration during the impact according to the actual operating conditions, such as occupant size, weight, occupant position, belt usage and crash severity. In this study,

  18. Risk and safety analysis of nuclear systems

    National Research Council Canada - National Science Library

    Lee, John C; McCormick, Norman J


    .... The first half of the book covers the principles of risk analysis, the techniques used to develop and update a reliability data base, the reliability of multi-component systems, Markov methods used...

  19. Safety of Hydrogen Systems Installed in Outdoor Enclosures

    Energy Technology Data Exchange (ETDEWEB)

    Barilo, Nick F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)


    The Hydrogen Safety Panel brings a broad cross-section of expertise from the industrial, government, and academic sectors to help advise the U.S. Department of Energy’s (DOE) Fuel Cell Technologies Office through its work in hydrogen safety, codes, and standards. The Panel’s initiatives in reviewing safety plans, conducting safety evaluations, identifying safety-related technical data gaps, and supporting safety knowledge tools and databases cover the gamut from research and development to demonstration and deployment. The Panel’s recent work has focused on the safe deployment of hydrogen and fuel cell systems in support of DOE efforts to accelerate fuel cell commercialization in early market applications: vehicle refueling, material handling equipment, backup power for warehouses and telecommunication sites, and portable power devices. This paper resulted from observations and considerations stemming from the Panel’s work on early market applications. This paper focuses on hydrogen system components that are installed in outdoor enclosures. These enclosures might alternatively be called “cabinets,” but for simplicity, they are all referred to as “enclosures” in this paper. These enclosures can provide a space where a flammable mixture of hydrogen and air might accumulate, creating the potential for a fire or explosion should an ignition occur. If the enclosure is large enough for a person to enter, and ventilation is inadequate, the hydrogen concentration could be high enough to asphyxiate a person who entered the space. Manufacturers, users, and government authorities rely on requirements described in codes to guide safe design and installation of such systems. Except for small enclosures used for hydrogen gas cylinders (gas cabinets), fuel cell power systems, and the enclosures that most people would describe as buildings, there are no hydrogen safety requirements for these enclosures, leaving gaps that must be addressed. This paper proposes that

  20. Survey of systems safety analysis methods and their application to nuclear waste management systems

    Energy Technology Data Exchange (ETDEWEB)

    Pelto, P.J.; Winegardner, W.K.; Gallucci, R.H.V.


    This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas for future study.

  1. Safety Justification of Software Systems. Software Based Safety Systems. Regulatory Inspection Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Dahll, Gustav (OECD Halden Project, Halden (NO)); Liwaang, Bo (Swedish Nuclear Power Inspectorate, Stockholm (Sweden)); Wainwright, Norman (Wainwright Safety Advice (GB))


    The introduction of new software based technology in the safety systems in nuclear power plants also makes it necessary to develop new strategies for regulatory review and assessment of these new systems that is more focused on reviewing the processes at the different phases in design phases during the system life cycle. It is a general requirement that the licensee shall perform different kinds of reviews. From a regulatory point of view it is more cost effective to assess that the design activities at the suppliers and the review activities within the development project are performed with good quality. But the change from more technical reviews over to the development process oriented approach also cause problems. When reviewing development and quality aspects there are no 'hard facts' that can be judged against some specified criteria, the issues are more 'soft' and are more to build up structure of arguments and evidences that the requirements are met. The regulatory review strategy must therefore change to follow the development process over the whole life cycle from concept phase until installation and operation. Even if we know what factors that is of interest we need some guidance on how to interpret and judge the information.For that purpose SKl started research activities in this area at the end of the 1990s. In the first phase, in co-operation with Gustav Dahll at the Halden project, a life cycle model was selected. For the different phases a qualitative influence net was constructed of the type that is used in Bayesian Believe Network together with a discussion on different issues involved. In the second phase of the research work, in co-operation with Norman Wainwright, a former NII inspector, information from a selection of the most important sources as guidelines, IAEA and EC reports etc, was mapped into the influence net structure (the total list on used sources are in the report). The result is presented in the form of

  2. Process Control Systems in the Chemical Industry: Safety vs. Security

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey Hahn; Thomas Anderson


    Traditionally, the primary focus of the chemical industry has been safety and productivity. However, recent threats to our nation’s critical infrastructure have prompted a tightening of security measures across many different industry sectors. Reducing vulnerabilities of control systems against physical and cyber attack is necessary to ensure the safety, security and effective functioning of these systems. The U.S. Department of Homeland Security has developed a strategy to secure these vulnerabilities. Crucial to this strategy is the Control Systems Security and Test Center (CSSTC) established to test and analyze control systems equipment. In addition, the CSSTC promotes a proactive, collaborative approach to increase industry's awareness of standards, products and processes that can enhance the security of control systems. This paper outlines measures that can be taken to enhance the cybersecurity of process control systems in the chemical sector.

  3. Evaluation of food safety management systems in Serbian dairy industry

    Directory of Open Access Journals (Sweden)

    Igor Tomašević


    Full Text Available This paper reports incentives, costs, difficulties and benefits of food safety management systems implementation in the Serbian dairy industry. The survey involved 27 food business operators with the national milk and dairy market share of 65 %. Almost two thirds of the assessed dairy producers (70.4 % claimed that they had a fully operational and certified HACCP system in place, while 29.6 % implemented HACCP, but had no third party certification. ISO 22000 was implemented and certified in 29.6 % of the companies, while only 11.1 % had implemented and certified IFS standard. The most important incentive for implementing food safety management systems for Serbian dairy producers was to increase and improve safety and quality of dairy products. The cost of product investigation/analysis and hiring external consultants were related to the initial set-up of food safety management system with the greatest importance. Serbian dairy industry was not greatly concerned by the financial side of implementing food safety management systems due to the fact that majority of prerequisite programmes were in place and regularly used by almost 100 % of the producers surveyed. The presence of competency gap between the generic knowledge for manufacturing food products and the knowledge necessary to develop and implement food safety management systems was confirmed, despite the fact that 58.8 % of Serbian dairy managers had university level of education. Our study brings about the innovation emphasizing the attitudes and the motivation of the food production staff as the most important barrier for the development and implementation of HACCP. The most important identified benefit was increased safety of dairy products with the mean rank scores of 6.85. The increased customer confidence and working discipline of staff employed in food processing were also found as important benefits of implementing/operating HACCP. The study shows that the level of HACCP


    CERN Document Server

    M. Plagge, C. Schaefer and N. Dupont


    Fire Safety – Essential for a particle detector The CMS detector is a marvel of high technology, one of the most precise particle measurement devices we have built until now. Of course it has to be protected from external and internal incidents like the ones that can occur from fires. Due to the fire load, the permanent availability of oxygen and the presence of various ignition sources mostly based on electricity this has to be addressed. Starting from the beam pipe towards the magnet coil, the detector is protected by flooding it with pure gaseous nitrogen during operation. The outer shell of CMS, namely the yoke and the muon chambers are then covered by an emergency inertion system also based on nitrogen. To ensure maximum fire safety, all materials used comply with the CERN regulations IS 23 and IS 41 with only a few exceptions. Every piece of the 30-tonne polyethylene shielding is high-density material, borated, boxed within steel and coated with intumescent (a paint that creates a thick co...

  5. Segmentation Scheme for Safety Enhancement of Engineered Safety Features Component Control System

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sangseok; Sohn, Kwangyoung [Korea Reliability Technology and System, Daejeon (Korea, Republic of); Lee, Junku; Park, Geunok [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    Common Caused Failure (CCF) or undetectable failure would adversely impact safety functions of ESF-CCS in the existing nuclear power plants. We propose the segmentation scheme to solve these problems. Main function assignment to segments in the proposed segmentation scheme is based on functional dependency and critical function success path by using the dependency depth matrix. The segment has functional independence and physical isolation. The segmentation structure is that prohibit failure propagation to others from undetectable failures. Therefore, the segmentation system structure has robustness to undetectable failures. The segmentation system structure has functional diversity. The specific function in the segment defected by CCF, the specific function could be maintained by diverse control function that assigned to other segments. Device level control signals and system level control signals are separated and also control signal and status signals are separated due to signal transmission paths are allocated independently based on signal type. In this kind of design, single device failure or failures on signal path in the channel couldn't result in the loss of all segmented functions simultaneously. Thus the proposed segmentation function is the design scheme that improves availability of safety functions. In conventional ESF-CCS, the single controller generates the signal to control the multiple safety functions, and the reliability is achieved by multiplication within the channel. This design has a drawback causing the loss of multiple functions due to the CCF (Common Cause Failure) and single failure Heterogeneous controller guarantees the diversity ensuring the execution of safety functions against the CCF and single failure, but requiring a lot of resources like manpower and cost. The segmentation technology based on the compartmentalization and functional diversification decreases the CCF and single failure nonetheless the identical types of

  6. A visual-analytics system for railway safety management. (United States)

    Lira, Wallace P; Alves, Ronnie; Costa, Jean M R; Pessin, Gustavo; Galvao, Lilyan; Cardoso, Ana C; de Souza, Cleidson R B


    The working environment of railways is challenging and complex and often involves high-risk operations. These operations affect both the company staff and inhabitants of the towns and cities alongside the railway lines. To reduce the employees' and public's exposure to risk, railway companies adopt strategies involving trained safety personnel, advanced forms of technology, and special work processes. Nevertheless, unfortunate incidents still occur. To assist railway safety management, researchers developed a visual-analytics system. Using a data analytics workflow, it compiles an incident risk index that processes information about railway incidents. It displays the index on a geographical map, together with socioeconomic information about the associated towns and cities. Feedback on this system suggests that safety engineers and experts can use it to make and communicate decisions.

  7. Can cyclist safety be improved with intelligent transport systems? (United States)

    Silla, Anne; Leden, Lars; Rämä, Pirkko; Scholliers, Johan; Van Noort, Martijn; Bell, Daniel


    In recent years, Intelligent Transport Systems (ITS) have assisted in the decrease of road traffic fatalities, particularly amongst passenger car occupants. Vulnerable Road Users (VRUs) such as pedestrians, cyclists, moped riders and motorcyclists, however, have not been that much in focus when developing ITS. Therefore, there is a clear need for ITS which specifically address VRUs as an integrated element of the traffic system. This paper presents the results of a quantitative safety impact assessment of five systems that were estimated to have high potential to improve the safety of cyclists, namely: Blind Spot Detection (BSD), Bicycle to Vehicle communication (B2V), Intersection safety (INS), Pedestrian and Cyclist Detection System+Emergency Braking (PCDS+EBR) and VRU Beacon System (VBS). An ex-ante assessment method proposed by Kulmala (2010) targeted to assess the effects of ITS for cars was applied and further developed in this study to assess the safety impacts of ITS specifically designed for VRUs. The main results of the assessment showed that all investigated systems affect cyclist safety in a positive way by preventing fatalities and injuries. The estimates considering 2012 accident data and full penetration showed that the highest effects could be obtained by the implementation of PCDS+EBR and B2V, whereas VBS had the lowest effect. The estimated yearly reduction in cyclist fatalities in the EU-28 varied between 77 and 286 per system. A forecast for 2030, taking into accounts the estimated accident trends and penetration rates, showed the highest effects for PCDS+EBR and BSD. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. System safety analysis of an autonomous mobile robot

    Energy Technology Data Exchange (ETDEWEB)

    Bartos, R.J.


    Analysis of the safety of operating and maintaining the Stored Waste Autonomous Mobile Inspector (SWAMI) II in a hazardous environment at the Fernald Environmental Management Project (FEMP) was completed. The SWAMI II is a version of a commercial robot, the HelpMate{trademark} robot produced by the Transitions Research Corporation, which is being updated to incorporate the systems required for inspecting mixed toxic chemical and radioactive waste drums at the FEMP. It also has modified obstacle detection and collision avoidance subsystems. The robot will autonomously travel down the aisles in storage warehouses to record images of containers and collect other data which are transmitted to an inspector at a remote computer terminal. A previous study showed the SWAMI II has economic feasibility. The SWAMI II will more accurately locate radioactive contamination than human inspectors. This thesis includes a System Safety Hazard Analysis and a quantitative Fault Tree Analysis (FTA). The objectives of the analyses are to prevent potentially serious events and to derive a comprehensive set of safety requirements from which the safety of the SWAMI II and other autonomous mobile robots can be evaluated. The Computer-Aided Fault Tree Analysis (CAFTA{copyright}) software is utilized for the FTA. The FTA shows that more than 99% of the safety risk occurs during maintenance, and that when the derived safety requirements are implemented the rate of serious events is reduced to below one event per million operating hours. Training and procedures in SWAMI II operation and maintenance provide an added safety margin. This study will promote the safe use of the SWAMI II and other autonomous mobile robots in the emerging technology of mobile robotic inspection.

  9. Performance scorecard for occupational safety and health management systems

    Directory of Open Access Journals (Sweden)

    Hernâni Veloso Neto


    Full Text Available The pro-active and systematic search for best performances should be the two assumptions of any management system, so safety and health management in organizations must also be guided by these same precepts. However, the scientific production evidences that the performance evaluation processes in safety and health continue to be guided, in their essence, by intermittency, reactivity and negativity, which are not consistent with the assumptions referenced above. Therefore, it is essential that health and safety at work management systems (HSW MS are structured from an active and positive viewpoint, focusing on continuous improvement. This implies considering performance evaluation processes that incorporate, on the one hand, monitoring, measuring and verification procedures, and on the other hand, structured matrixes of results that capture the key factors of success, by mobilizing both reactive and proactive indicators. One of the instruments that can fulfill these precepts of health and safety performance evaluation is the SafetyCard, a performance scorecard for HSW MS that we developed and will seek to outline and demonstrate over this paper.

  10. Investigating the Effects of Safety Management System Practice, Benevolent Leadership and Core Self-evaluations on Cabin Crew Safety Behavior

    National Research Council Canada - National Science Library

    CHEN, Ching-Fu; CHEN, Shu-Chuan


    .... Specifically, we specify perceived airlines' Safety Management System practice, department managers' benevolent leadership and individual core self-evaluations as three factors affecting cabin crew...

  11. The effect of using road safety equipment and systems and ...

    African Journals Online (AJOL)

    In the present communities transportation is a critical component of human life, and one of the main categories in the specification transportation system is the subject of safety. Considering the number of road accidents and deaths caused by it, unfortunately Iran is at the top of countries with the highest number of deaths in ...


    Directory of Open Access Journals (Sweden)

    A. K. Blagorazumov


    Full Text Available This article describes the Aviation Safety Information Monitoring System, namely the architecture, algorithm of collecting and processing of the information as well as user interfaces. With the proposed model one can estimate the efficiency of the operation of aviation security in case of unlawful interference in air transport.

  13. Computer Aided Method for System Safety and Reliability Assessments (United States)


    is a misconception that system safety as an engineering entity is focused on protecting personnel from accidents by focusing on slips, trips, falls...Category 4 • Communications satellites • Fossil fuel/hydro-electric power plants • Water filtration plants • Short-range missiles/rockets

  14. Food safety management systems performance in the lamb production chain

    NARCIS (Netherlands)

    Oses, S.M.; Luning, P.A.; Jacxsens, L.; Jaime, I.; Rovira, J.


    This study describes a performance measurement of implemented food safety management system (FSMS) along the lamb chain using an FSMS-diagnostic instrument (FSMS-DI) and a Microbiological Assessment Scheme (MAS). Three slaughterhouses, 1 processing plant and 5 butcher shops were evaluated. All the

  15. Automated Systems for Road Safety control in a Developing World

    African Journals Online (AJOL)


    Dec 1, 2012 ... concern to researchers and road management agencies. ... critical analysis on road safety reveals many problems facing the control of road traffic. An .... tools, processes, and methodologies are key components to any decision support system and provide end users with rich reporting, monitoring, and.

  16. SAFETY

    CERN Multimedia

    Niels Dupont


    CERN Safety rules and Radiation Protection at CMS The CERN Safety rules are defined by the Occupational Health & Safety and Environmental Protection Unit (HSE Unit), CERN’s institutional authority and central Safety organ attached to the Director General. In particular the Radiation Protection group (DGS-RP1) ensures that personnel on the CERN sites and the public are protected from potentially harmful effects of ionising radiation linked to CERN activities. The RP Group fulfils its mandate in collaboration with the CERN departments owning or operating sources of ionising radiation and having the responsibility for Radiation Safety of these sources. The specific responsibilities concerning "Radiation Safety" and "Radiation Protection" are delegated as follows: Radiation Safety is the responsibility of every CERN Department owning radiation sources or using radiation sources put at its disposition. These Departments are in charge of implementing the requi...

  17. Safety monitoring in the Vaccine Adverse Event Reporting System (VAERS). (United States)

    Shimabukuro, Tom T; Nguyen, Michael; Martin, David; DeStefano, Frank


    The Centers for Disease Control and Prevention (CDC) and the U.S. Food and Drug Administration (FDA) conduct post-licensure vaccine safety monitoring using the Vaccine Adverse Event Reporting System (VAERS), a spontaneous (or passive) reporting system. This means that after a vaccine is approved, CDC and FDA continue to monitor safety while it is distributed in the marketplace for use by collecting and analyzing spontaneous reports of adverse events that occur in persons following vaccination. Various methods and statistical techniques are used to analyze VAERS data, which CDC and FDA use to guide further safety evaluations and inform decisions around vaccine recommendations and regulatory action. VAERS data must be interpreted with caution due to the inherent limitations of passive surveillance. VAERS is primarily a safety signal detection and hypothesis generating system. Generally, VAERS data cannot be used to determine if a vaccine caused an adverse event. VAERS data interpreted alone or out of context can lead to erroneous conclusions about cause and effect as well as the risk of adverse events occurring following vaccination. CDC makes VAERS data available to the public and readily accessible online. We describe fundamental vaccine safety concepts, provide an overview of VAERS for healthcare professionals who provide vaccinations and might want to report or better understand a vaccine adverse event, and explain how CDC and FDA analyze VAERS data. We also describe strengths and limitations, and address common misconceptions about VAERS. Information in this review will be helpful for healthcare professionals counseling patients, parents, and others on vaccine safety and benefit-risk balance of vaccination. Published by Elsevier Ltd.

  18. A Validation Metrics Framework for Safety-Critical Software-Intensive Systems (United States)


    Analysis Achieved HAS Hazard Analysis Space HAZOP Hazard and Operability HRI Hazard Risk Index IAP Interface Adapter Panel IFF Identification...Hazard and Operability Studies ( HAZOP ), etc., - Independent Safety Audit Reports, - Safety Requirements Specification, - System Safety

  19. Railway automatic safety protection system based on GPS

    Directory of Open Access Journals (Sweden)

    Fu Hai Juan


    Full Text Available The automatic protection system of railway safety is designed for the railway construction workers to protect alarm, and the safety protection device by using GPS satellite positioning system to acquire location information of the operating point, through the CTC/TDCS system and computer monitoring system for the running of the train position and the arithmetic distance. Achieving timely and continuously forecasts about the distance of the train which is apart from the operating point to prompt the voice alarm of the approaching train. Using digital technology to realize the function of the traditional analog interphone, eliminates the quality problems of the call. With the GSM-R, mobile wireless transmission channel and terminal technology, it overcomes the restrictions of the analog interphone which influenced by communication distance and more problems of blind areas. Finally to achieve practical, convenient, applicable and adaptable design goals.

  20. Improving safety margin of LWRs by rethinking the emergency core cooling system criteria and safety system capacity

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Youho, E-mail:; Kim, Bokyung, E-mail:; NO, Hee Cheon, E-mail:


    Highlights: • Zircaloy embrittlement criteria can increase to 1370 °C for CP-ECR lower than 13%. • The draft ECCS criteria of U.S. NRC allow less than 5% in power margin. • The Japanese fracture-based criteria allow around 5% in power margin. • Increasing SIT inventory is effective in assuring safety margin for power uprates. - Abstract: This study investigates the engineering compatibility between emergency core cooling system criteria and safety water injection systems, in the pursuit of safety margin increase of light water reactors. This study proposes an acceptable temperature increase to 1370 °C as long as equivalent cladding reacted calculated by the Cathcart–Pawel equation is below 13%, after an extensive literature review. The influence of different ECCS criteria on the safety margin during large break loss of coolant accident is investigated for OPR-1000 by the system code MARS-KS, implemented with the KINS-REM method. The fracture-based emergency core cooling system (ECCS) criteria proposed in this study are shown to enable power margins up to 10%. In the meantime, the draft U.S. NRC’s embrittlement criteria (burnup-sensitive) and Japanese fracture-based criteria are shown to allow less than 5%, and around 5% of power margins, respectively. Increasing safety injection tank (SIT) water inventory is the key, yet convenient, way of assuring safety margin for power increase. More than 20% increase in the SIT water inventory is required to allow 15% power margins, for the U.S. NRC’s burnup-dependent embrittlement criteria. Controlling SIT water inventory would be a useful option that could allow the industrial desire to pursue power margins even under the recent atmosphere of imposing stricter ECCS criteria for the considerable burnup effects.

  1. Safety Metrics for Human-Computer Controlled Systems (United States)

    Leveson, Nancy G; Hatanaka, Iwao


    The rapid growth of computer technology and innovation has played a significant role in the rise of computer automation of human tasks in modem production systems across all industries. Although the rationale for automation has been to eliminate "human error" or to relieve humans from manual repetitive tasks, various computer-related hazards and accidents have emerged as a direct result of increased system complexity attributed to computer automation. The risk assessment techniques utilized for electromechanical systems are not suitable for today's software-intensive systems or complex human-computer controlled systems.This thesis will propose a new systemic model-based framework for analyzing risk in safety-critical systems where both computers and humans are controlling safety-critical functions. A new systems accident model will be developed based upon modem systems theory and human cognitive processes to better characterize system accidents, the role of human operators, and the influence of software in its direct control of significant system functions Better risk assessments will then be achievable through the application of this new framework to complex human-computer controlled systems.

  2. When learners surpass their models: mathematical modeling of learning from an inconsistent source. (United States)

    Mandelshtam, Yelena; Komarova, Natalia L


    It has been reported in the literature that both adults and children can, to a different degree, modify and regularize the often-inconsistent linguistic input they receive. We present a new algorithm to model and investigate the learning process of a learner mastering a set of (grammatical or lexical) forms from an inconsistent source. The algorithm is related to reinforcement learning and drift-diffusion models of decision making, and possesses several psychologically relevant properties such as fidelity, robustness, discounting, and computational simplicity. It demonstrates how a learner can successfully learn from or even surpass its imperfect source. We use the data collected by Singleton and Newport (Cognit Psychol 49(4):370-407, 2004) on the performance of a 7-year-boy Simon, who mastered the American Sign Language (ASL) by learning it from his parents, both of whom were imperfect speakers of ASL. We show that the algorithm possesses a frequency boosting property, whereby the frequency of the most common form of the source is increased by the learner. We also explain several key features of Simon's ASL.

  3. Licensing process for safety-critical software-based systems

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, P. [VTT Automation, Espoo (Finland); Korhonen, J. [VTT Electronics, Espoo (Finland); Pulkkinen, U. [VTT Automation, Espoo (Finland)


    System vendors nowadays propose software-based technology even for the most critical safety functions in nuclear power plants. Due to the nature of software faults and the way they cause system failures new methods are needed for the safety and reliability evaluation of these systems. In the research project 'Programmable automation systems in nuclear power plants (OHA)', financed together by the Radiation and Nuclear Safety Authority (STUK), the Ministry of Trade and Industry (KTM) and the Technical Research Centre of Finland (VTT), various safety assessment methods and tools for software based systems are developed and evaluated. As a part of the OHA-work a reference model for the licensing process for software-based safety automation systems is defined. The licensing process is defined as the set of interrelated activities whose purpose is to produce and assess evidence concerning the safety and reliability of the system/application to be licensed and to make the decision about the granting the construction and operation permissions based on this evidence. The parties of the licensing process are the authority, the licensee (the utility company), system vendors and their subcontractors and possible external independent assessors. The responsibility about the production of the evidence in first place lies at the licensee who in most cases rests heavily on the vendor expertise. The evaluation and gauging of the evidence is carried out by the authority (possibly using external experts), who also can acquire additional evidence by using their own (independent) methods and tools. Central issue in the licensing process is to combine the quality evidence about the system development process with the information acquired through tests, analyses and operational experience. The purpose of the licensing process described in this report is to act as a reference model both for the authority and the licensee when planning the licensing of individual applications

  4. Prospective Safety Analysis and the Complex Aviation System (United States)

    Smith, Brian E.


    Fatal accident rates in commercial passenger aviation are at historic lows yet have plateaued and are not showing evidence of further safety advances. Modern aircraft accidents reflect both historic causal factors and new unexpected "Black Swan" events. The ever-increasing complexity of the aviation system, along with its associated technology and organizational relationships, provides fertile ground for fresh problems. It is important to take a proactive approach to aviation safety by working to identify novel causation mechanisms for future aviation accidents before they happen. Progress has been made in using of historic data to identify the telltale signals preceding aviation accidents and incidents, using the large repositories of discrete and continuous data on aircraft and air traffic control performance and information reported by front-line personnel. Nevertheless, the aviation community is increasingly embracing predictive approaches to aviation safety. The "prospective workshop" early assessment tool described in this paper represents an approach toward this prospective mindset-one that attempts to identify the future vectors of aviation and asks the question: "What haven't we considered in our current safety assessments?" New causation mechanisms threatening aviation safety will arise in the future because new (or revised) systems and procedures will have to be used under future contextual conditions that have not been properly anticipated. Many simulation models exist for demonstrating the safety cases of new operational concepts and technologies. However the results from such models can only be as valid as the accuracy and completeness of assumptions made about the future context in which the new operational concepts and/or technologies will be immersed. Of course that future has not happened yet. What is needed is a reasonably high-confidence description of the future operational context, capturing critical contextual characteristics that modulate

  5. Comparative analysis of existing food safety culture evaluation systems


    Jespersen, Lone; Griffiths, Mansel; Wallace, Carol Anne


    The purpose of the research was firstly, to analyze existing culture evaluation systems for commonalities and differences in research quality, applied validation strategies, and content. Secondly, to suggest a simple structure of food safety cultural dimensions to help unify the culture evaluation field. To achieve these goals, a comparison of eight culture evaluation models applied to varing degrees in the food industry was conducted. The systems were found to vary significantly in applied v...

  6. The elements of a commercial human spaceflight safety reporting system (United States)

    Christensen, Ian


    In its report on the SpaceShipTwo accident the National Transportation Safety Board (NTSB) included in its recommendations that the Federal Aviation Administration (FAA) ;in collaboration with the commercial spaceflight industry, continue work to implement a database of lessons learned from commercial space mishap investigations and encourage commercial space industry members to voluntarily submit lessons learned.; In its official response to the NTSB the FAA supported this recommendation and indicated it has initiated an iterative process to put into place a framework for a cooperative safety data sharing process including the sharing of lessons learned, and trends analysis. Such a framework is an important element of an overall commercial human spaceflight safety system.

  7. Development of the Continued Improvement System for Nuclear Safety Culture

    Energy Technology Data Exchange (ETDEWEB)

    Park, H. C.; Park, H. G.; Park, Y. W.; Park, J. Y. [KAIST, Daejeon (Korea, Republic of)


    It has been found that almost 80 % of the incidents and accidents occurred recently, such as the Fukushima Daiichi disaster and Domestic SBO accident etc. were analyzed to be caused from human errors. (IAEA NES NG-G-2.1) Which strongly claims the importance of the safety culture system. Accordingly, it should be away from a cursory approach like one-off field survey or Snap shop which were being conducted at present for the continued improvement of safety culture. This study introduces an analytical methodology which approaches the generic form of the safety both consciously and unconsciously expressed with behavior, thoughts, and attitude etc. This study was implemented only for open materials such as Inspection report, incidents and accidents reports, QA documents because of the limitation in accessibility to data. More effective use with securing operational data will be possible in future.

  8. Internet of Things Based Combustible Ice Safety Monitoring System Framework (United States)

    Sun, Enji


    As the development of human society, more energy is requires to meet the need of human daily lives. New energies play a significant role in solving the problems of serious environmental pollution and resources exhaustion in the present world. Combustible ice is essentially frozen natural gas, which can literally be lit on fire bringing a whole new meaning to fire and ice with less pollutant. This paper analysed the advantages and risks on the uses of combustible ice. By compare to other kinds of alternative energies, the advantages of the uses of combustible ice were concluded. The combustible ice basic physical characters and safety risks were analysed. The developments troubles and key utilizations of combustible ice were predicted in the end. A real-time safety monitoring system framework based on the internet of things (IOT) was built to be applied in the future mining, which provide a brand new way to monitoring the combustible ice mining safety.

  9. Safety analysis and review system (SARS) assessment report

    Energy Technology Data Exchange (ETDEWEB)

    Browne, E.T.


    Under DOE Order 5481.1, Safety Analysis and Review System for DOE Operations, safety analyses are required for DOE projects in order to ensure that: (1) potential hazards are systematically identified; (2) potential impacts are analyzed; (3) reasonable measures have been taken to eliminate, control, or mitigate the hazards; and (4) there is documented management authorization of the DOE operation based on an objective assessment of the adequacy of the safety analysis. This report is intended to provide the DOE Office of Plans and Technology Assessment (OPTA) with an independent evaluation of the adequacy of the ongoing safety analysis effort. As part of this effort, a number of site visits and interviews were conducted, and FE SARS documents were reviewed. The latter included SARS Implementation Plans for a number of FE field offices, as well as safety analysis reports completed for certain FE operations. This report summarizes SARS related efforts at the DOE field offices visited and evaluates the extent to which they fulfill the requirements of DOE 5481.1.

  10. Evaluating the effectiveness of active vehicle safety systems. (United States)

    Jeong, Eunbi; Oh, Cheol


    Advanced vehicle safety systems have been widely introduced in transportation systems and are expected to enhance traffic safety. However, these technologies mainly focus on assisting individual vehicles that are equipped with them, and less effort has been made to identify the effect of vehicular technologies on the traffic stream. This study proposed a methodology to assess the effectiveness of active vehicle safety systems (AVSSs), which represent a promising technology to prevent traffic crashes and mitigate injury severity. The proposed AVSS consists of longitudinal and lateral vehicle control systems, which corresponds to the Level 2 vehicle automation presented by the National Highway Safety Administration (NHTSA). The effectiveness evaluation for the proposed technology was conducted in terms of crash potential reduction and congestion mitigation. A microscopic traffic simulator, VISSIM, was used to simulate freeway traffic stream and collect vehicle-maneuvering data. In addition, an external application program interface, VISSIM's COM-interface, was used to implement the AVSS. A surrogate safety assessment model (SSAM) was used to derive indirect safety measures to evaluate the effectiveness of the AVSS. A 16.7-km freeway stretch between the Nakdong and Seonsan interchanges on Korean freeway 45 was selected for the simulation experiments to evaluate the effectiveness of AVSS. A total of five simulation runs for each evaluation scenario were conducted. For the non-incident conditions, the rear-end and lane-change conflicts were reduced by 78.8% and 17.3%, respectively, under the level of service (LOS) D traffic conditions. In addition, the average delay was reduced by 55.5%. However, the system's effectiveness was weakened in the LOS A-C categories. Under incident traffic conditions, the number of rear-end conflicts was reduced by approximately 9.7%. Vehicle delays were reduced by approximately 43.9% with 100% of market penetration rate (MPR). These results

  11. A systems-based food safety evaluation: an experimental approach. (United States)

    Higgins, Charles L; Hartfield, Barry S


    Food establishments are complex systems with inputs, subsystems, underlying forces that affect the system, outputs, and feedback. Building on past exploration of the hazard analysis critical control point concept and Ludwig von Bertalanffy General Systems Theory, the National Park Service (NPS) is attempting to translate these ideas into a realistic field assessment of food service establishments and to use information gathered by these methods in efforts to improve food safety. Over the course of the last two years, an experimental systems-based methodology has been drafted, developed, and tested by the NPS Public Health Program. This methodology is described in this paper.

  12. Evaluation of intelligent transport systems impact on school transport safety

    Directory of Open Access Journals (Sweden)

    Jankowska-Karpa Dagmara


    Full Text Available The integrated system of safe transport of children to school using Intelligent Transport Systems was developed and implemented in four locations across Europe under the Safeway2School (SW2S project, funded by the EU. The SW2S system evaluation included speed measurements and an eye-tracking experiment carried out among drivers who used the school bus route, where selected elements of the system were tested. The subject of the evaluation were the following system elements: pedestrian safety system at the bus stop (Intelligent Bus Stop and tags for children, Driver Support System, applications for parents’ and students’ mobile phones, bus stop inventory tool and data server. A new sign designed for buses and bus stops to inform about child transportation/children waiting at the bus stop was added to the system. Training schemes for system users were also provided. The article presents evaluation results of the impact of selected elements of the SW2S system on school transport safety in Poland.

  13. A Novel Control Algorithm for Integration of Active and Passive Vehicle Safety Systems in Frontal Collisions

    Directory of Open Access Journals (Sweden)

    Daniel Wallner


    Full Text Available The present paper investigates an approach to integrate active and passive safety systems of passenger cars. Worldwide, the introduction of Integrated Safety Systems and Advanced Driver Assistance Systems (ADAS is considered to continue the today

  14. Energy Storage System Safety: Plan Review and Inspection Checklist

    Energy Technology Data Exchange (ETDEWEB)

    Cole, Pam C (PNNL); Conover, David R (PNNL)


    Codes, standards, and regulations (CSR) governing the design, construction, installation, commissioning, and operation of the built environment are intended to protect the public health, safety, and welfare. While these documents change over time to address new technology and new safety challenges, there is generally some lag time between the introduction of a technology into the market and the time it is specifically covered in model codes and standards developed in the voluntary sector. After their development, there is also a timeframe of at least a year or two until the codes and standards are adopted. Until existing model codes and standards are updated or new ones are developed and then adopted, one seeking to deploy energy storage technologies or needing to verify the safety of an installation may be challenged in trying to apply currently implemented CSRs to an energy storage system (ESS). The Energy Storage System Guide for Compliance with Safety Codes and Standards1 (CG), developed in June 2016, is intended to help address the acceptability of the design and construction of stationary ESSs, their component parts, and the siting, installation, commissioning, operations, maintenance, and repair/renovation of ESS within the built environment.

  15. On the safety of aircraft systems: A case study

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Guridi, G.; Hall, R.E.; Fullwood, R.R.


    An airplane is a highly engineered system incorporating control- and feedback-loops which often, and realistically, are non-linear because the equations describing such feedback contain products of state variables, trigonometric or square-root functions, or other types of non-linear terms. The feedback provided by the pilot (crew) of the airplane also is typically non-linear because it has the same mathematical characteristics. An airplane is designed with systems to prevent and mitigate undesired events. If an undesired triggering event occurs, an accident may process in different ways depending on the effectiveness of such systems. In addition, the progression of some accidents requires that the operating crew take corrective action(s), which may modify the configuration of some systems. The safety assessment of an aircraft system typically is carried out using ARP (Aerospace Recommended Practice) 4761 (SAE, 1995) methods, such as Fault Tree Analysis (FTA) and Failure Mode and Effects Analysis (FMEA). Such methods may be called static because they model an aircraft system on its nominal configuration during a mission time, but they do not incorporate the action(s) taken by the operating crew, nor the dynamic behavior (non-linearities) of the system (airplane) as a function of time. Probabilistic Safety Assessment (PSA), also known as Probabilistic Risk Assessment (PRA), has been applied to highly engineered systems, such as aircraft and nuclear power plants. PSA encompasses a wide variety of methods, including event tree analysis (ETA), FTA, and common-cause analysis, among others. PSA should not be confused with ARP 4761`s proposed PSSA (Preliminary System Safety Assessment); as its name implies, PSSA is a preliminary assessment at the system level consisting of FTA and FMEA.

  16. Effect of Awareness about Health, Safety and Environment Management System on Safety Climate and Risk Perception in Oil Refinery Employees

    Directory of Open Access Journals (Sweden)

    Ahmadi Marzaleh M. MSc,


    Full Text Available Abstract Aims: Health, safety and environment is an integrated and convergence system and also a synergistic arrangement of human resources, facilities and equipment. This study aimed to determine the relationship of safety climate and perception of risk with the awareness level of HSE management system among oil refineries employees. Instrument & Methods: This cross-sectional study was performed at 2016 in all Kermanshah Oil Refinery employees. “Demographic characteristic”, “safety climate”, “perception of risk” and “awareness of the HSE management system” questionnaires were used for data collection. Data was analyzed in SPSS 22 statistical software using Pearson correlation and ANOVA tests. Findings: The average of total awareness of HSE was 20.85±4.82. The average of safety climate was 157.04±22.42. The average of perception of risk was 3.45±0.84. There was a significant relationship between awareness of HSE management system and safety climate (r=0.219; p=0.001, but there was no significant relationship between awareness of HSE management system and perception of risk (r=0.137; p=0.128. The relationship between perception of risk and safety climate was significant (r=0.651; p=0.001. Conclusion: Oil refinery's employees have the moderate awareness of HSE management system, high perception of risk and positive safety climate. By increasing the perception of risk and safety climate, the safety performance of the refinery staffs increase.

  17. 75 FR 15620 - Federal Motor Vehicle Safety Standards; Air Brake Systems (United States)


    ... National Highway Traffic Safety Administration 49 CFR Part 571 RIN 2127-AK62 Federal Motor Vehicle Safety... that amended the Federal motor vehicle safety standard for air brake systems by requiring substantial... 37122) amending Federal Motor Vehicle Safety Standard (FMVSS) No. 121, Air Brake Systems, to require...


    Directory of Open Access Journals (Sweden)



    Full Text Available Smart Power Team is currently working on the design of an urban electric vehicle designed to compete in the Shell Eco-marathon. One important aspect of this type of vehicle characteristics is it safety. The project of advanced driver assistance systems has included some proposals of such systems and the concept of their execution. The first concept, BLIS (Blind Spot Information System, is to build a system of informing a driver about vehicles appearing in the blind spot. The system constitutes a second concept, CDIS (Collision Detection and Information System, and it is designed to detect a vehicle collision and inform the team. Further systems are: DPMS (Dew Point Measurement System - a system which does not allow a situation, where the windows are fogged, OHRS (Overtaking Horn Reminder System - a system which checks overtaking and MSS (main supervision system - a supervisory system. These concepts are based on the assumption of the use of laser sensors, photoelectric, humidity and temperature, and other commercially available systems. The article presents a detailed description of driver assistance systems and virtual prototyping methodology for these systems, as well as the numerical results of the verification of one of the systems.

  19. Effect of Ischemic Preconditioning on Endurance Performance Does Not Surpass Placebo. (United States)

    Sabino-Carvalho, Jeann L; Lopes, Thiago R; Obeid-Freitas, Tiago; Ferreira, Thiago N; Succi, José E; Silva, Antônio C; Silva, Bruno M


    Recent studies have reported ischemic preconditioning (IPC) can acutely improve endurance exercise performance in athletes. However, placebo and nocebo effects have not been sufficiently controlled, and the effect on aerobic metabolism parameters that determine endurance performance (e.g., oxygen cost of running, lactate threshold, and maximal oxygen uptake [V˙O2max]) has been equivocal. Thus, we circumvented limitations from previous studies to test the effect of IPC on aerobic metabolism parameters and endurance performance in well-trained runners. Eighteen runners (14 men/4 women) were submitted to three interventions, in random order: IPC; sham intervention (SHAM); and resting control (CT). Subjects were told both IPC and SHAM would improve performance compared to CT (i.e., similar placebo induction), and IPC would be harmless despite circulatory occlusion sensations (i.e., nocebo avoidance). Next, pulmonary ventilation and gas exchange, blood lactate concentration, and perceived effort were measured during a discontinuous incremental test on a treadmill. Then, a supramaximal test was used to verify the V˙O2max and assess endurance performance (i.e., time to exhaustion). Ventilation, oxygen uptake, carbon dioxide output, lactate concentration, and perceived effort were similar among IPC, SHAM, and CT throughout the discontinuous incremental test (P > 0.05). Oxygen cost of running, lactate threshold, and V˙O2max were also similar among interventions (P > 0.05). Time to exhaustion was longer after IPC (mean ± SEM, 165.34 ± 12.34 s) and SHAM (164.38 ± 11.71 s) than CT (143.98 ± 12.09 s; P = 0.02 and 0.03, respectively), but similar between IPC and SHAM (P = 1.00). IPC did not change aerobic metabolism parameters, whereas improved endurance performance. The IPC improvement, however, did not surpass the effect of a placebo intervention.

  20. Quantifying Pilot Contribution to Flight Safety during Hydraulic Systems Failure (United States)

    Kramer, Lynda J.; Etherington, Timothy J.; Bailey, Randall E.; Kennedy, Kellie D.


    Accident statistics cite the flight crew as a causal factor in over 60% of large transport aircraft fatal accidents. Yet, a well-trained and well-qualified pilot is acknowledged as the critical center point of aircraft systems safety and an integral safety component of the entire commercial aviation system. The latter statement, while generally accepted, cannot be verified because little or no quantitative data exists on how and how many accidents/incidents are averted by crew actions. A joint NASA/FAA high-fidelity motion-base human-in-the-loop test was conducted using a Level D certified Boeing 737-800 simulator to evaluate the pilot's contribution to safety-of-flight during routine air carrier flight operations and in response to aircraft system failures. To quantify the human's contribution, crew complement (two-crew, reduced crew, single pilot) was used as the independent variable in a between-subjects design. This paper details the crew's actions, including decision-making, and responses while dealing with a hydraulic systems leak - one of 6 total non-normal events that were simulated in this experiment.

  1. European Workshop Industrical Computer Science Systems approach to design for safety (United States)

    Zalewski, Janusz


    This paper presents guidelines on designing systems for safety, developed by the Technical Committee 7 on Reliability and Safety of the European Workshop on Industrial Computer Systems. The focus is on complementing the traditional development process by adding the following four steps: (1) overall safety analysis; (2) analysis of the functional specifications; (3) designing for safety; (4) validation of design. Quantitative assessment of safety is possible by means of a modular questionnaire covering various aspects of the major stages of system development.

  2. Automatic road traffic safety management system in urban areas

    Directory of Open Access Journals (Sweden)

    Oskarbski Jacek


    Full Text Available Traffic incidents and accidents contribute to decreasing levels of transport system reliability and safety. Traffic management and emergency systems on the road, using, among others, automatic detection, video surveillance, communication technologies and institutional solutions improve the organization of the work of various departments involved in traffic and safety management. Automation of incident management helps to reduce the time of a rescue operation as well as of the normalization of the flow of traffic after completion of a rescue operation, which also affects the reduction of the risk of secondary accidents and contributes to reducing their severity. The paper presents the possibility of including city traffic departments in the process of incident management. The results of research on the automatic incident detection in cities are also presented.

  3. A Project Manager's View of Safety-Critical Systems (United States)

    Docker, Thomas

    This paper presents a project manager's view that safety-critical systems are not a special case or category of product development, but is one dimension that is a requirement in increasingly more systems. As with any product development, the degree to which a safety-critical product is tested or proved should be based on 'cost of failure' that, in the final analysis, is a commercial decision based on benefits and business risk. It is argued that with the emphasis on cost of failure, project teams can be more effective in producing safer products, particularly in terms of focusing testing. With effectiveness in mind, an approach to linking benefits to products is described, along with how this relates to requirements and acceptance criteria. Possible impacts of the use of standards in a project are also discussed. Case studies are used to reinforce concepts and highlight concerns.

  4. Development of Operational Safety Monitoring System and Emergency Preparedness Advisory System for CANDU Reactors (I)

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ma Woong; Shin, Hyeong Ki; Lee, Sang Kyu; Kim, Hyun Koon; Yoo, Kun Joong; Ryu, Yong Ho [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of); Son, Han Seong; Song, Deok Yong [ENESYS, Daejeon (Korea, Republic of)


    As increase of operating nuclear power plants, an accident monitoring system is essential to ensure the operational safety of nuclear power plant. Thus, KINS has developed the Computerized Advisory System for a Radiological Emergency (CARE) system to monitor the operating status of nuclear power plant continuously. However, during the accidents or/and incidents some parameters could not be provided from the process computer of nuclear power plant to the CARE system due to limitation of To enhance the CARE system more effective for CANDU reactors, there is a need to provide complement the feature of the CARE in such a way to providing the operating parameters using to using safety analysis tool such as CANDU Integrated Safety Analysis System (CISAS) for CANDU reactors. In this study, to enhance the safety monitoring measurement two computerized systems such as a CANDU Operational Safety Monitoring System (COSMOS) and prototype of CANDU Emergency Preparedness Advisory System (CEPAS) are developed. This study introduces the two integrated safety monitoring system using the R and D products of the national mid- and long-term R and D such as CISAS and ISSAC code.

  5. Configuration and Data Management Process and the System Safety Professional (United States)

    Shivers, Charles Herbert; Parker, Nelson C. (Technical Monitor)


    This article presents a discussion of the configuration management (CM) and the Data Management (DM) functions and provides a perspective of the importance of configuration and data management processes to the success of system safety activities. The article addresses the basic requirements of configuration and data management generally based on NASA configuration and data management policies and practices, although the concepts are likely to represent processes of any public or private organization's well-designed configuration and data management program.

  6. Safety analysis report for packaging (onsite) sample pig transport system

    Energy Technology Data Exchange (ETDEWEB)

    MCCOY, J.C.


    This Safety Analysis Report for Packaging (SARP) provides a technical evaluation of the Sample Pig Transport System as compared to the requirements of the U.S. Department of Energy, Richland Operations Office (RL) Order 5480.1, Change 1, Chapter III. The evaluation concludes that the package is acceptable for the onsite transport of Type B, fissile excepted radioactive materials when used in accordance with this document.

  7. Autonomous Flight Safety System September 27, 2005, Aircraft Test (United States)

    Simpson, James C.


    This report describes the first aircraft test of the Autonomous Flight Safety System (AFSS). The test was conducted on September 27, 2005, near Kennedy Space Center (KSC) using a privately-owned single-engine plane and evaluated the performance of several basic flight safety rules using real-time data onboard a moving aerial vehicle. This test follows the first road test of AFSS conducted in February 2005 at KSC. AFSS is a joint KSC and Wallops Flight Facility (WEF) project that is in its third phase of development. AFSS is an independent subsystem intended for use with Expendable Launch Vehicles that uses tracking data from redundant onboard sensors to autonomously make flight termination decisions using software-based rules implemented on redundant flight processors. The goals of this project are to increase capabilities by allowing launches from locations that do not have or cannot afford extensive ground-based range safety assets, to decrease range costs, and to decrease reaction time for special situations. The mission rules are configured for each operation by the responsible Range Safety authorities and can be loosely categorized in four major categories: Parameter Threshold Violations, Physical Boundary Violations present position and instantaneous impact point (TIP), Gate Rules static and dynamic, and a Green-Time Rule. Examples of each of these rules were evaluated during this aircraft test.

  8. The Art World's Concept of Negative Space Applied to System Safety Management (United States)

    Goodin, Ronnie


    Tools from several different disciplines can improve system safety management. This paper relates the Art World with our system safety world showing useful art schools of thought applied to system safety management; developing an art theory- system safety bridge. This bridge is then used to demonstrate relations with risk management, the legal system, personnel management and basic management (establishing priorities.) One goal of this presentation/paper is simply to be a fun diversion from the many technical topics presented during the conference.

  9. Maximum Safety Regenerative Power Tracking for DC Traction Power Systems

    Directory of Open Access Journals (Sweden)

    Guifu Du


    Full Text Available Direct current (DC traction power systems are widely used in metro transport systems, with running rails usually being used as return conductors. When traction current flows through the running rails, a potential voltage known as “rail potential” is generated between the rails and ground. Currently, abnormal rises of rail potential exist in many railway lines during the operation of railway systems. Excessively high rail potentials pose a threat to human life and to devices connected to the rails. In this paper, the effect of regenerative power distribution on rail potential is analyzed. Maximum safety regenerative power tracking is proposed for the control of maximum absolute rail potential and energy consumption during the operation of DC traction power systems. The dwell time of multiple trains at each station and the trigger voltage of the regenerative energy absorbing device (READ are optimized based on an improved particle swarm optimization (PSO algorithm to manage the distribution of regenerative power. In this way, the maximum absolute rail potential and energy consumption of DC traction power systems can be reduced. The operation data of Guangzhou Metro Line 2 are used in the simulations, and the results show that the scheme can reduce the maximum absolute rail potential and energy consumption effectively and guarantee the safety in energy saving of DC traction power systems.

  10. System Study: High-Pressure Safety Injection 1998-2014

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, John Alton [Idaho National Lab. (INL), Idaho Falls, ID (United States). Risk Assessment and Management Services Dept.


    This report presents an unreliability evaluation of the high-pressure safety injection system (HPSI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2014 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10 year period, while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPSI results.

  11. System Study: High-Pressure Safety Injection 1998–2013

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, John Alton [Idaho National Lab. (INL), Idaho Falls, ID (United States). Risk Assessment and Management Services Dept.


    This report presents an unreliability evaluation of the high-pressure safety injection system (HPSI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2013 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10-year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPSI results.

  12. System Study: High-Pressure Safety Injection 1998–2012

    Energy Technology Data Exchange (ETDEWEB)

    T. E. Wierman


    This report presents an unreliability evaluation of the high-pressure safety injection system (HPSI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2012 for selected components were obtained from the Equipment Performance and Information Exchange (EPIX). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPSI results.

  13. Safety critical systems handbook a straightforward guide to functional safety : IEC 61508 (2010 edition) and related standards

    CERN Document Server

    Smith, David J


    Electrical, electronic and programmable electronic systems increasingly carry out safety functions to guard workers and the public against injury or death and the environment against pollution. The international functional safety standard IEC 61508 was revised in 2010, and this is the first comprehensive guide available to the revised standard. As functional safety is applicable to many industries, this book will have a wide readership beyond the chemical and process sector, including oil and gas, power generation, nuclear, aircraft, and automotive industries, plus project, instrumentation, design, and control engineers. * The only comprehensive guide to IEC 61508, updated to cover the 2010 amendments, that will ensure engineers are compliant with the latest process safety systems design and operation standards* Helps readers understand the process required to apply safety critical systems standards* Real-world approach helps users to interpret the standard, with case studies and best practice design examples...

  14. Cyber Security Test Strategy for Non-safety Display System

    Energy Technology Data Exchange (ETDEWEB)

    Son, Han Seong [Joongbu University, Geumsan (Korea, Republic of); Kim, Hee Eun [KAIST, Daejeon (Korea, Republic of)


    Cyber security has been a big issue since the instrumentation and control (I and C) system of nuclear power plant (NPP) is digitalized. A cyber-attack on NPP should be dealt with seriously because it might cause not only economic loss but also the radioactive material release. Researches on the consequences of cyber-attack onto NPP from a safety point of view have been conducted. A previous study shows the risk effect brought by initiation of event and deterioration of mitigation function by cyber terror. Although this study made conservative assumptions and simplifications, it gives an insight on the effect of cyber-attack. Another study shows that the error on a non-safety display system could cause wrong actions of operators. According to this previous study, the failure of the operator action caused by a cyber-attack on a display system might threaten the safety of the NPP by limiting appropriate mitigation actions. This study suggests a test strategy focusing on the cyber-attack on the information and display system, which might cause the failure of operator. The test strategy can be suggested to evaluate and complement security measures. Identifying whether a cyber-attack on the information and display system can affect the mitigation actions of operator, the strategy to obtain test scenarios is suggested. The failure of mitigation scenario is identified first. Then, for the test target in the scenario, software failure modes are applied to identify realistic failure scenarios. Testing should be performed for those scenarios to confirm the integrity of data and to assure effectiveness of security measures.

  15. 76 FR 55829 - Federal Motor Vehicle Safety Standards; Electronic Stability Control Systems (United States)


    ... National Highway Traffic Safety Administration 49 CFR Part 571 RIN 2127-AL02 Federal Motor Vehicle Safety Standards; Electronic Stability Control Systems AGENCY: National Highway Traffic Safety Administration... changes to a new Federal motor vehicle safety standard requiring light vehicles to be equipped with...

  16. 78 FR 9623 - Federal Motor Vehicle Safety Standards; Air Brake Systems (United States)


    ... National Highway Traffic Safety Administration 49 CFR Part 571 RIN 2127-AL11 Federal Motor Vehicle Safety... published a final rule that amended the Federal motor vehicle safety standard for air brake systems by... published a final rule in the Federal Register amending Federal Motor Vehicle Safety Standard (FMVSS) No...

  17. 33 CFR 96.240 - What functional requirements must a safety management system meet? (United States)


    ... requirements must a safety management system meet? The functional requirements of a safety management system... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false What functional requirements must a safety management system meet? 96.240 Section 96.240 Navigation and Navigable Waters COAST GUARD...

  18. Integrated Safety Management System Phase I Verification for the Plutonium Finishing Plant (PFP) [VOL 1 & 2

    Energy Technology Data Exchange (ETDEWEB)

    SETH, S.S.


    U.S. Department of Energy (DOE) Policy 450.4, Safety Management System Policy commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex as a means of accomplishing its missions safely. DOE Acquisition Regulation 970.5204-2 requires that contractors manage and perform work in accordance with a documented safety management system.

  19. 77 FR 51649 - Federal Motor Vehicle Safety Standards; Motorcycle Brake Systems (United States)


    ... passenger cars.\\7\\ \\6\\ Response to Petitions for Reconsideration, Motorcycle Brake Systems, 37 FR 11973... CFR Part 571 Federal Motor Vehicle Safety Standards; Motorcycle Brake Systems; Final Rule #0;#0... Federal Motor Vehicle Safety Standards; Motorcycle Brake Systems AGENCY: National Highway Traffic Safety...

  20. 78 FR 47012 - Developing Software Life Cycle Processes Used in Safety Systems of Nuclear Power Plants (United States)


    ... COMMISSION Developing Software Life Cycle Processes Used in Safety Systems of Nuclear Power Plants AGENCY... Software Life Cycle Processes for Digital Computer Software used in Safety Systems of Nuclear Power Plants... design quality in software used in safety systems in nuclear power plants. ADDRESSES: Please refer to...

  1. 76 FR 67201 - Information Collection Activities: Oil and Gas Production Safety Systems; Submitted for Office of... (United States)


    ... Production Safety Systems; Submitted for Office of Management and Budget (OMB) Review; Comment Request ACTION... the paperwork requirements in the regulations under Subpart H, ``Oil and Gas Production Safety Systems... H, Oil and Gas Production Safety Systems. Abstract: The Outer Continental Shelf (OCS) Lands Act, as...

  2. 76 FR 50748 - Information Collection Activity: Production Safety Systems, Revision of a Collection; Submitted... (United States)


    ... in the regulations under ``Oil and Gas Production Safety Systems'' (OMB No. 1010-0059). DATES: Submit... 250, subpart H, Oil and Gas Production Safety Systems. OMB Control Number: 1010-0059. Abstract: The... public at large. Facility Production Safety System Applications are subject to cost recovery, and BOEMRE...

  3. 30 CFR 250.802 - Design, installation, and operation of surface production-safety systems. (United States)


    ... production-safety systems. 250.802 Section 250.802 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... Gas Production Safety Systems § 250.802 Design, installation, and operation of surface production-safety systems. (a) General. All production facilities, including separators, treaters, compressors...

  4. Radiation methods in decision support system for food safety

    Directory of Open Access Journals (Sweden)

    Migdal Wojciech


    Full Text Available Mathematical model is the basis for computer decision support system (DSS connected with food security strategy, in which food irradiation is one of the methods used for elimination of substance with pathogens. Such system can support an organisation of many different activities in the area of food safety. It can be designed for a specific region, country, etc., and is addressed to State Sanitary Inspection offices. The paper demonstrates the capabilities of the system in modeling activities of sanitary inspection teams aimed at pathogen elimination with the use of electron beam irradiation in procedures of utilisation of animal originated food, related packaging, or other microbiologically contaminated materials. It describes new application of both computer supported decision systems and radiation processing. The elaborated mathematical models show human activities in the process of microbiological contamination elimination.


    Directory of Open Access Journals (Sweden)

    Gordan Badurina


    Full Text Available Managing the right level of inventory is critical in order to achieve the targeted level of customer service, but it also carries significant cost in supply chain. In majority of cases companies define safety stock on the most downstream level, i.e. the finished product level, using different analytical methods. Safety stock on upstream level, however, usually covers only those problems which companies face on that particular level (uncertainty of delivery, issues in production, etc.. This paper looks into optimizing safety stock in a pharmaceutical supply considering the three stages inventory system. The problem is defined as a single criterion mixed integer programming problem. The objective is to minimize the inventory cost while the service level is predetermined. In order to coordinate inventories at all echelons, the variable representing the so-called service time is introduced. Because of the problem dimensions, metaheuristics based on genetic algorithm and simulated annealing are constructed and compared, using real data from a Croatian pharmaceutical company. The computational results are presented evidencing improvements in minimizing inventory costs.

  6. Supplementary safety system 1/4 scale testing

    Energy Technology Data Exchange (ETDEWEB)

    Garrett, R.L.; Paik, I.K.


    During the course of updating the K-Reactor Safety Analysis Report Chapter 15 in 1990, it was identified that the current Supplementary Safety System (SSS) may not be adequate in protecting the reactor during the process water pump coastdown initiated by a loss of AC power when the safety rods are assumed to fail. A SSS modification project was initiated to add an additional ink injection pathway near the pump suction. In addition, the Department of Energy raised a question on the thermal buoyancy effects on moderator flow pattern and ink dispersion in the moderator space. The development and documentation of a two-dimensional code called MODFLOW was undertaken to describe the problem. This report discusses the results of the moderator flow and ink (Gadolinium Poison Solution - GPS) dispersion tests designed to provide qualified data for validation and benchmarking of the MODFLOW computer code with the secondary objectives being the development of concentration profiles and video footage of simulated GPS dispersion under steady-state and transient flow conditions.

  7. System Interface for an Integrated Intelligent Safety System (ISS for Vehicle Applications

    Directory of Open Access Journals (Sweden)

    Mahammad A. Hannan


    Full Text Available This paper deals with the interface-relevant activity of a vehicle integrated intelligent safety system (ISS that includes an airbag deployment decision system (ADDS and a tire pressure monitoring system (TPMS. A program is developed in LabWindows/CVI, using C for prototype implementation. The prototype is primarily concerned with the interconnection between hardware objects such as a load cell, web camera, accelerometer, TPM tire module and receiver module, DAQ card, CPU card and a touch screen. Several safety subsystems, including image processing, weight sensing and crash detection systems, are integrated, and their outputs are combined to yield intelligent decisions regarding airbag deployment. The integrated safety system also monitors tire pressure and temperature. Testing and experimentation with this ISS suggests that the system is unique, robust, intelligent, and appropriate for in-vehicle applications.

  8. Ship Power System Analysis Based on Safety Aspects

    Directory of Open Access Journals (Sweden)

    Urbaha Margarita


    Full Text Available This article analyses the reasons for the reduction of insulating resistance, processes influencing them and isolation diagnostic methods. It provides a short description of electrical safety situation on ships with isolated neutral electrical power systems. It also covers the methods of protecting personnel from electric shock or preventing ignition or arching damage at the fault location with the help of fault current compensation. Principal fault current compensation circuit diagrams are analysed by using the minimum value and time of transient fault current as criteria.

  9. Safety-Enclosure System For MOCVD Process Chamber (United States)

    Singletery, James, Jr.; Velasquez, Hugo; Warner, Joseph


    Safety-enclosure system filled with nitrogen surrounds reaction chamber in which metallo-organic chemical vapor deposition (MOCVD) performed. Designed to protect against explosions and/or escaping toxic gases and particulates. Gas-purification subsystem ensures during loading and unloading of process materials, interior of MOCVD chamber exposed to less than 1 ppm of oxygen and less than 5 ppm of water in nitrogen atmosphere. Toxic byproducts of MOCVD process collected within inert atmosphere. Enclosure strong enough to contain any fragments in unlikely event of explosion.

  10. Linking better shiftwork arrangements with safety and health management systems. (United States)

    Kogi, Kazutaka


    Various support measures useful for promoting joint change approaches to the improvement of both shiftworking arrangements and safety and health management systems were reviewed. A particular focus was placed on enterprise-level risk reduction measures linking working hours and management systems. Voluntary industry-based guidelines on night and shift work for department stores and the chemical, automobile and electrical equipment industries were examined. Survey results that had led to the compilation of practicable measures to be included in these guidelines were also examined. The common support measures were then compared with ergonomic checkpoints for plant maintenance work involving irregular nightshifts. On the basis of this analysis, a new night and shift work checklist was designed. Both the guidelines and the plant maintenance work checkpoints were found to commonly cover multiple issues including work schedules and various job-related risks. This close link between shiftwork arrangements and risk management was important as shiftworkers in these industries considered teamwork and welfare services to be essential for managing risks associated with night and shift work. Four areas found suitable for participatory improvement by managers and workers were work schedules, ergonomic work tasks, work environment and training. The checklist designed to facilitate participatory change processes covered all these areas. The checklist developed to describe feasible workplace actions was suitable for integration with comprehensive safety and health management systems and offered valuable opportunities for improving working time arrangements and job content together.

  11. Reviewing real-time performance of nuclear reactor safety systems

    Energy Technology Data Exchange (ETDEWEB)

    Preckshot, G.G. [Lawrence Livermore National Lab., CA (United States)


    The purpose of this paper is to recommend regulatory guidance for reviewers examining real-time performance of computer-based safety systems used in nuclear power plants. Three areas of guidance are covered in this report. The first area covers how to determine if, when, and what prototypes should be required of developers to make a convincing demonstration that specific problems have been solved or that performance goals have been met. The second area has recommendations for timing analyses that will prove that the real-time system will meet its safety-imposed deadlines. The third area has description of means for assessing expected or actual real-time performance before, during, and after development is completed. To ensure that the delivered real-time software product meets performance goals, the paper recommends certain types of code-execution and communications scheduling. Technical background is provided in the appendix on methods of timing analysis, scheduling real-time computations, prototyping, real-time software development approaches, modeling and measurement, and real-time operating systems.

  12. Cascade Distillation System Design for Safety and Mission Assurance (United States)

    Sarguisingh, Miriam; Callahan, Michael R.; Okon, Shira


    Per the NASA Human Health, Life Support and Habitation System Technology Area 06 report "crewed missions venturing beyond Low-Earth Orbit (LEO) will require technologies with improved reliability, reduced mass, self-sufficiency, and minimal logistical needs as an emergency or quick-return option will not be feasible".1 To meet this need, the development team of the second generation Cascade Distillation System (CDS 2.0) chose a development approach that explicitly incorporate consideration of safety, mission assurance, and autonomy. The CDS 2.0 preliminary design focused on establishing a functional baseline that meets the CDS core capabilities and performance. The critical design phase is now focused on incorporating features through a deliberative process of establishing the systems failure modes and effects, identifying mitigation strategies, and evaluating the merit of the proposed actions through analysis and test. This paper details results of this effort on the CDS 2.0 design.

  13. Decay Power Calculation for Safety Analysis of Innovative Reactor Systems

    Energy Technology Data Exchange (ETDEWEB)

    Shwageraus, E.; Fridman, E. [Department of Nuclear Engineering, Ben-Gurion University of the Negev Beer-Sheva 84105 (Israel)


    In this work, we verified the decay heat calculation capabilities of BGCore computer code system developed recently at Ben-Gurion University. Decay power was calculated for a typical UO{sub 2} fuel in Pressurized Water Reactor environment using BGCore code and using procedure prescribed by the ANS/ANSI-2005 standard. Very good agreement between the two methods was obtained. Once BGCore calculation capabilities were verified, we calculated decay power as a function of time after shutdown for various reactors with innovative fuels, for which no standard procedure is currently available. Notable differences were observed for decay power of the advanced reactors as compared with conventional UO{sub 2} LWR. The observed differences suggest that the design of new reactors safety systems must be based on corresponding decay power curves for each individual case in order to assure the desired performance of such systems. (authors)

  14. Advancing a sociotechnical systems approach to workplace safety – developing the conceptual framework (United States)

    Carayon, Pascale; Hancock, Peter; Leveson, Nancy; Noy, Ian; Sznelwar, Laerte; van Hootegem, Geert


    Traditional efforts to deal with the enormous problem of workplace safety have proved insufficient, as they have tended to neglect the broader sociotechnical environment that surrounds workers. Here, we advocate a sociotechnical systems approach that describes the complex multi-level system factors that contribute to workplace safety. From the literature on sociotechnical systems, complex systems and safety, we develop a sociotechnical model of workplace safety with concentric layers of the work system, socio-organisational context and the external environment. The future challenges that are identified through the model are highlighted. Practitioner Summary: Understanding the environmental, organisational and work system factors that contribute to workplace safety will help to develop more effective and integrated solutions to deal with persistent workplace safety problems. Solutions to improve workplace safety need to recognise the broad sociotechnical system and the respective interactions between the system elements and levels. PMID:25831959

  15. An integrated risk sensing system for geo-structural safety

    Directory of Open Access Journals (Sweden)

    H.W. Huang


    Full Text Available Over the last decades, geo-structures are experiencing a rapid development in China. The potential risks inherent in the huge amount of construction and asset operation projects in China were well managed in the major project, i.e. the project of Shanghai Yangtze tunnel in 2002. Since then, risk assessment of geo-structures has been gradually developed from a qualitative manner to a quantitative manner. However, the current practices of risk management have been paid considerable attention to the assessment, but little on risk control. As a result, the responses to risks occurrences after a comprehensive assessment are basically too late. In this paper, a smart system for risk sensing incorporating the wireless sensor network (WSN on-site visualization techniques and the resilience-based repair strategy was proposed. The merit of this system is the real-time monitoring for geo-structural performance and dynamic pre-warning for safety of on-site workers. The sectional convergence, joint opening, and seepage of segmental lining of shield tunnel were monitored by the micro-electro-mechanical systems (MEMS based sensors. The light emitting diode (LED coupling with the above WSN system was used to indicate different risk levels on site. By sensing the risks and telling the risks in real time, the geo-risks could be controlled and the safety of geo-structures could be assured to a certain degree. Finally, a resilience-based analysis model was proposed for designing the repair strategy by using the measured data from the WSN system. The application and efficiency of this system have been validated by two cases including Shanghai metro tunnel and underwater road tunnel.

  16. Food safety systems in a small dairy factory: implementation, major challenges, and assessment of systems' performances. (United States)

    Cusato, Sueli; Gameiro, Augusto H; Corassin, Carlos H; Sant'ana, Anderson S; Cruz, Adriano G; Faria, José de Assis F; de Oliveira, Carlos Augusto F


    The present study describes the implementation of a food safety system in a dairy processing plant located in the State of São Paulo, Brazil, and the challenges found during the process. In addition, microbiological indicators have been used to assess system's implementation performance. The steps involved in the implementation of a food safety system included a diagnosis of the prerequisites, implementation of the good manufacturing practices (GMPs), sanitation standard operating procedures (SSOPs), training of the food handlers, and hazard analysis and critical control point (HACCP). In the initial diagnosis, conformity with 70.7% (n=106) of the items analyzed was observed. A total of 12 critical control points (CCPs) were identified: (1) reception of the raw milk, (2) storage of the raw milk, (3 and 4) reception of the ingredients and packaging, (5) milk pasteurization, (6 and 7) fermentation and cooling, (8) addition of ingredients, (9) filling, (10) storage of the finished product, (11) dispatching of the product, and (12) sanitization of the equipment. After implementation of the food safety system, a significant reduction in the yeast and mold count was observed (p<0.05). The main difficulties encountered for the implementation of food safety system were related to the implementation of actions established in the flow chart and to the need for constant training/adherence of the workers to the system. Despite this, the implementation of the food safety system was shown to be challenging, but feasible to be reached by small-scale food industries.

  17. Managing health and safety risks: Implications for tailoring health and safety management system practices. (United States)

    Willmer, D R; Haas, E J


    As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to site-specific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council's Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization's site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

  18. System and safety studies of accelerator driven systems for transmutation. Annual report 2007

    Energy Technology Data Exchange (ETDEWEB)

    Arzhanov, Vasily; Fokau, Andrei; Persson, Calle; Runevall, Odd; Sandberg, Nils; Tesinsky, Milan; Wallenius, Janne; Youpeng Zhang (Div. of Reactor Physics, Royal Institute of Technology, Stockholm (Sweden))


    Within the project 'System and safety studies of accelerator driven systems for transmutation', research on design and safety of sub-critical reactors for recycling of minor actinides is performed. During 2007, the reactor physics division at KTH has calculated safety parameters for EFIT-400 with cermet fuel, permitting to start the transient safety analysis. The accuracy of different reactivity meters applied to the YALINA facility was assessed and neutron detection studies were performed. A model to address deviations from point kinetic behaviour was developed. Studies of basic radiation damage physics included calculations of vacancy formation and activation enthalpies in bcc niobium. In order to predict the oxygen potential of inert matrix fuels, a thermo-chemical model for mixed actinide oxides was implemented in a phase equilibrium code

  19. Integrated Design and Analysis Environment for Safety Critical Human-Automation Systems Project (United States)

    National Aeronautics and Space Administration — Flight deck systems, like many safety critical systems, often involve complex interactions between multiple human operators, automated subsystems, and physical...

  20. Safety problems in vehicles with adaptive cruise control system

    Directory of Open Access Journals (Sweden)

    Yadav Arun K.


    Full Text Available In today’s world automotive industries are still putting efforts towards more autonomous vehicles (AVs. The main concern of introducing the autonomous technology is safety of driver. According to a survey 90% of accidents happen due to mistake of driver. The adaptive cruise control system (ACC is a system which combines cruise control with a collision avoidance system. The ACC system is based on laser and radar technologies. This system is capable of controlling the velocity of vehicle automatically to match the velocity of car, bus or truck in front of vehicle. If the lead vehicle gets slow down or accelerate, than ACC system automatically matches that velocity. The proposed paper is focusing on more accurate methods of detecting the preceding vehicle by using a radar and lidar sensors by considering the vehicle side slip and by controlling the distance between two vehicles. By using this approach i.e. logic for calculation of former vehicle distance and controlling the throttle valve of ACC equipped vehicle, an improvement in driving stability was achieved. The own contribution results with fuel efficient driving and with more safer and reliable driving system, but still some improvements are going on to make it more safe and reliable.

  1. Comprehensive analysis and differentiated assessment of food safety control systems: a diagnostic instrument

    NARCIS (Netherlands)

    Luning, P.A.; Bango, L.; Kussaga, J.; Rovira, J.; Marcelis, W.J.


    In this article, an instrument is presented to diagnose microbial safety control activities in a food safety management system. The need of such a tool is derived from the importance of microbial safety control and the need for improvement of existing control systems. Careful diagnosis of these

  2. 75 FR 56112 - Integrated Food Safety System Online Collaboration Development-Cooperative Agreement With the... (United States)


    ... HUMAN SERVICES Food and Drug Administration Integrated Food Safety System Online Collaboration... the primary goals of the NCFPD is to allow FDA to meet the White House Food Safety Working Group... information sharing in the development of an integrated food safety system, and the development and...

  3. Spent Nuclear Fuel (SNF) project Integrated Safety Management System phase I and II Verification Review Plan

    Energy Technology Data Exchange (ETDEWEB)

    CARTER, R.P.


    The U.S. Department of Energy (DOE) commits to accomplishing its mission safely. To ensure this objective is met, DOE issued DOE P 450.4, Safety Management System Policy, and incorporated safety management into the DOE Acquisition Regulations ([DEAR] 48 CFR 970.5204-2 and 90.5204-78). Integrated Safety Management (ISM) requires contractors to integrate safety into management and work practices at all levels so that missions are achieved while protecting the public, the worker, and the environment. The contractor is required to describe the Integrated Safety Management System (ISMS) to be used to implement the safety performance objective.

  4. Lost in Debate: The Safety of Domestic Unmanned Aircraft Systems

    Directory of Open Access Journals (Sweden)

    Yeonmin Cho


    Full Text Available The United States is poised to integrate commercial unmanned aircraft systems (UAS into the national airspace and enable government entities to use UAS in a more expedient manner. This policy change, mandated by the Federal Aviation Administration (FAA Modernization and Reform Act of 2012, offers new economic, social and scientific opportunities as well as enhanced law enforcement capacity. However, such benefits will be accompanied by concerns over misuse and abuse of the new technologies by criminals and terrorists. Privacy has been the focus of public debate over the more widespread use of UAS. This paper examines a variety of issues related to allowing broad UAS operations in domestic airspace, and puts forth that safety should be the top priority of policy makers in their effort to integrate UAS into the national airspace system.

  5. Design, Operations, and Safety Report for the MERIT Target System

    Energy Technology Data Exchange (ETDEWEB)

    Graves, Van B [ORNL; Spampinato, Philip Thomas [ORNL


    The Mercury Intense Target Project (MERIT) is a proof-of-principal experiment to determine the feasibility of using a free-jet of Hg as a spallation target in a Neutrino Factory or a Muon Collider facility. The 1-cm-diameter, 20-m/sec jet will be generated inside a 15-Tesla magnetic field, and high-speed optical diagnostics will be used to photograph the interaction between the Hg jet and a 24-GeV proton beam.The experiment is scheduled to be conducted at CERN in 2007. ORNL is responsible for the design, fabrication, and testing of a system to deliver the Hg jet within the confines of the 15-cm magnet bore. This report documents the functional and safety requirements of the Hg system along with descriptions of its interfaces to the other experimental equipment.

  6. Commercial-off-the-shelf (COTS) hardware and software for train control applications : system safety considerations. (United States)


    The objective of this study was to assess the feasibility of using commercial off-the-shelf(COTS)processor-based systems for safety- related railroad applications. From the safety perspective,the fundamental challenges of using COTS products are most...

  7. Release mitigation spray safety systems for chemical demilitarization applications.

    Energy Technology Data Exchange (ETDEWEB)

    Leonard, Jonathan; Tezak, Matthew Stephen; Brockmann, John E.; Servantes, Brandon; Sanchez, Andres L.; Tucker, Mark David; Allen, Ashley N.; Wilson, Mollye C.; Lucero, Daniel A.; Betty, Rita G.


    Sandia National Laboratories has conducted proof-of-concept experiments demonstrating effective knockdown and neutralization of aerosolized CBW simulants using charged DF-200 decontaminant sprays. DF-200 is an aqueous decontaminant, developed by Sandia National Laboratories, and procured and fielded by the US Military. Of significance is the potential application of this fundamental technology to numerous applications including mitigation and neutralization of releases arising during chemical demilitarization operations. A release mitigation spray safety system will remove airborne contaminants from an accidental release during operations, to protect personnel and limit contamination. Sandia National Laboratories recently (November, 2008) secured funding from the US Army's Program Manager for Non-Stockpile Chemical Materials Agency (PMNSCMA) to investigate use of mitigation spray systems for chemical demilitarization applications. For non-stockpile processes, mitigation spray systems co-located with the current Explosive Destruction System (EDS) will provide security both as an operational protective measure and in the event of an accidental release. Additionally, 'tented' mitigation spray systems for native or foreign remediation and recovery operations will contain accidental releases arising from removal of underground, unstable CBW munitions. A mitigation spray system for highly controlled stockpile operations will provide defense from accidental spills or leaks during routine procedures.

  8. The dual axis radiographic hydrodynamic test (DARHT) facility personnel safety system (PSS) control system

    Energy Technology Data Exchange (ETDEWEB)

    Jacquez, Edward B [Los Alamos National Laboratory


    The mission of the Dual Axis Radiograph Hydrodynamic Test (DARHT) Facility is to conduct experiments on dynamic events of extremely dense materials. The PSS control system is designed specifically to prevent personnel from becoming exposed to radiation and explosive hazards during machine operations and/or the firing site operation. This paper will outline the Radiation Safety System (RSS) and the High Explosive Safety System (HESS) which are computer-controlled sets of positive interlocks, warning devices, and other exclusion mechanisms that together form the PSS.

  9. [Expert investigation on food safety standard system framework construction in China]. (United States)

    He, Xiang; Yan, Weixing; Fan, Yongxiang; Zeng, Biao; Peng, Zhen; Sun, Zhenqiu


    Through investigating food safety standard framework among food safety experts, to summarize the basic elements and principles of food safety standard system, and provide policy advices for food safety standards framework. A survey was carried out among 415 experts from government, professional institutions and the food industry/enterprises using the National Food Safety Standard System Construction Consultation Questionnaire designed in the name of the Secretariat of National Food Safety Standard Committee. Experts have different advices in each group about the principles of food product standards, food additive product standards, food related product standards, hygienic practice, test methods. According to the results, the best solution not only may reflect experts awareness of the work of food safety standards situation, but also provide advices for setting and revision of food safety standards for the next. Through experts investigation, the framework and guiding principles of food safety standard had been built.

  10. Safety management of a complex R and D ground operating system (United States)

    Connors, J. F.; Maurer, R. A.


    A perspective on safety program management was developed for a complex R&D operating system, such as the NASA-Lewis Research Center. Using a systems approach, hazardous operations are subjected to third-party reviews by designated-area safety committees and are maintained under safety permit controls. To insure personnel alertness, emergency containment forces and employees are trained in dry-run emergency simulation exercises. The keys to real safety effectiveness are top management support and visibility of residual risks.

  11. Software safety analysis techniques for developing safety critical software in the digital protection system of the LMR

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jang Soo; Cheon, Se Woo; Kim, Chang Hoi; Sim, Yun Sub


    This report has described the software safety analysis techniques and the engineering guidelines for developing safety critical software to identify the state of the art in this field and to give the software safety engineer a trail map between the code and standards layer and the design methodology and documents layer. We have surveyed the management aspects of software safety activities during the software lifecycle in order to improve the safety. After identifying the conventional safety analysis techniques for systems, we have surveyed in details the software safety analysis techniques, software FMEA(Failure Mode and Effects Analysis), software HAZOP(Hazard and Operability Analysis), and software FTA(Fault Tree Analysis). We have also surveyed the state of the art in the software reliability assessment techniques. The most important results from the reliability techniques are not the specific probability numbers generated, but the insights into the risk importance of software features. To defend against potential common-mode failures, high quality, defense-in-depth, and diversity are considered to be key elements in digital I and C system design. To minimize the possibility of CMFs and thus increase the plant reliability, we have provided D-in-D and D analysis guidelines.

  12. Engineered safety systems. 2. act. and enl. ed.; Fahrsicherheitssysteme

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, H. (comp.)


    Modern motor cars and industrial vehicles have very efficient brakes, but even the best of brakes cannot prevent human drivers from panicking and braking too hard. The Bosch ABS antiblocking system ensures that a vehicle is under control even during emergency braking. The ASR slip control system prevents wheel spin during starting and acceleration. The latest development, the ESP dynamic control system ensures lateral stability and keeps the vehicle on track in all conditions. This book presents detail and current information on engineered safety systems, with clear descriptions of the most important systems and their components. (orig.) [German] Moderne Pkw und Nkw verfuegen ueber leistungsfaehige und zuverlaessige Bremsanlagen, die auch bei hohen Geschwindigkeiten sehr gute Bremswerte erzielen. Doch auch die besten Bremsen koennen nicht verhindern, dass ein Autofahrer bei schlechten Strassenverhaeltnissen oder in einer Schrecksituation falsch reagiert und zu stark auf das Bremspedal tritt. Mit dem Antiblockiersystem ABS von Bosch bleiben Fahrzeuge selbst bei einer Vollbremsung lenkbar und richtungsstabil. Auch die Antriebsschlupfregelung ASR entlastet den Fahrer, indem sie beim Anfahren und Beschleunigen das Durchdrehen der Antriebsraeder verhindert. Den letzten Stand der Entwicklung bildet die Fahrdynamikregelung ESP, die in allen denkbaren Fahrsituationen durch blitzschnelle gezielte Eingriffe in Motor, Getriebe und Bremsen fuer Stabilitaet sorgt und das Fahrzeug in der Spur haelt. Das Fachbuch informiert umfassend ueber die aktuelle Technik zur Fahrsicherheit. Der an Kfz-Technik interessierte Leser erhaelt damit eine ausfuehrliche, leicht verstaendliche Beschreibung der wichtigsten Steuerungssysteme und Komponenten. (orig.)

  13. Safety inspections in construction sites: A systems thinking perspective. (United States)

    Saurin, Tarcisio Abreu


    Although safety inspections carried out by government officers are important for the prevention of accidents, there is little in-depth knowledge on their outcomes and processes leading to these. This research deals with this gap by using systems thinking (ST) as a lens for obtaining insights into safety inspections in construction sites. Thirteen case studies of sites with prohibited works were carried out, discussing how four attributes of ST were used in the inspections. The studies were undertaken over 6 years, and sources of evidence involved participant observation, direct observations, analysis of documents and interviews. Two complementary ways for obtaining insights into inspections, based on ST, were identified: (i) the design of the study itself needs to be in line with ST; and (ii) data collection and analysis should focus on the agents involved in the inspections, the interactions between agents, the constraints and opportunities faced by agents, the outcomes of interactions, and the recommendations for influencing interactions. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Rail height effects on safety performance of Midwest Guardrail System. (United States)

    Asadollahi Pajouh, Mojdeh; Julin, Ramen D; Stolle, Cody S; Reid, John D; Faller, Ronald K


    Guardrail heights play a crucial role in the way that errant vehicles interact with roadside barriers. Low rail heights increase the propensity of vehicle rollover and override, whereas excessively tall rails promote underride. Further, rail mounting heights and post embedment depths may be altered by variations in roadside terrain. An increased guardrail height may be desirable to accommodate construction tolerances, soil erosion, frost heave, and future roadway overlays. This study aimed to investigate and identify a maximum safe installation height for the Midwest Guardrail System that would be robust and remain crashworthy before and after pavement overlays. A research investigation was performed to evaluate the safety performance of increased mounting heights for the standard 787-mm (31-in.)-tall Midwest Guardrail System (MGS) through crash testing and computer simulation. Two full-scale crash tests with small passenger cars were performed on the MGS with top-rail mounting heights of 864 and 914 mm (34 and 36 in.). Test results were then used to calibrate computer simulation models. In the first test, a small car impacted the MGS with 864-mm (34-in.) rail height at 102 km/h (63.6 mph) and 25.0° and was successfully redirected. In the second test, another small car impacted the MGS with a 914-mm (36-in.) rail height at 103 km/h (64.1 mph) and 25.6° and was successful. Both system heights satisfied the Manual for Assessing Safety Hardware (MASH) Test Level 3 (TL-3) evaluation criteria. Test results were then used to calibrate computer simulation models. A mounting height of 36 in. was determined to be the maximum guardrail height that would safely contain and redirect small car vehicles. Simulations confirmed that taller guardrail heights (i.e., 37 in.) would likely result in small car underride. In addition, simulation results indicated that passenger vehicle models were successfully contained by the 34- and 36-in.-tall MGS installed on approach slopes

  15. SAFETY

    CERN Multimedia

    C. Schaefer and N. Dupont


      “Safety is the highest priority”: this statement from CERN is endorsed by the CMS management. An interpretation of this statement may bring you to the conclusion that you should stop working in order to avoid risks. If the safety is the priority, work is not! This would be a misunderstanding and misinterpretation. One should understand that “working safely” or “operating safely” is the priority at CERN. CERN personnel are exposed to different hazards on many levels on a daily basis. However, risk analyses and assessments are done in order to limit the number and the gravity of accidents. For example, this process takes place each time you cross the road. The hazard is the moving vehicle, the stake is you and the risk might be the risk of collision between both. The same principle has to be applied during our daily work. In particular, keeping in mind the general principles of prevention defined in the late 1980s. These principles wer...

  16. KAERI software safety guideline for developing safety-critical software in digital instrumentation and control system of nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jang Soo; Kim, Jang Yeol; Eum, Heung Seop


    Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organization. The requirements for software important to safety of nuclear reactor are described in such positions and standards. Most of them are describing mandatory requirements, what shall be done, for the safety-critical software. The developers of such a software. However, there have been a lot of controversial factors on whether the work practices satisfy the regulatory requirements, and to justify the safety of such a system developed by the work practices, between the licenser and the licensee. We believe it is caused by the reason that there is a gap between the mandatory requirements (What) and the work practices (How). We have developed a guidance to fill such gap, which can be useful for both licenser and licensee to conduct a justification of the safety in the planning phase of developing the software for nuclear reactor protection systems. (author). 67 refs., 13 tabs., 2 figs.

  17. Quantifying system safety: A comparison of the SBOAT & Safety Barrier Manager tools

    DEFF Research Database (Denmark)

    Hansen, Zaza Nadja Lee; Duijm, Nijs Jan; Markert, Frank


    This paper presents two software tools for analyzing safety risks, SBOAT (Stochastic BPMN Optimisation and Analysis Tool) and SBM (SafetyBarrierManagerr). SBOAT employs principles from stochastic model checking to allow for the quantitative verification of workflows. SBM supports the creation...

  18. Safety management system of subcontractors’ works in foundry companies

    Directory of Open Access Journals (Sweden)

    M. Rączka


    Full Text Available Most companies use the services of subcontractors, either in their core business, or to support the work – e.g. maintenance. This poses the need for effective and systematic monitoring of the work of subcontractors, especially if they perform it on the premises of an enterprise. In some industries such as construction, energy, petrochemicals, metallurgy and foundry additional system requirements appear, particularly with regard to safety and the environment, a compliance with which is necessary to obtain an order. Often, conformity with these requirements must be confirmed with a certificate. The article presents examples of standardised special requirements, such as SCC /VCA, SCT / VCU, SQAS used for sub-contractors of construction work, maintenance, scaffolding etc. in the European Union member states.

  19. Preliminary safety evaluation for the plutonium stabilization and packaging system

    Energy Technology Data Exchange (ETDEWEB)

    Shapley, J.E., Fluor Daniel Hanford


    This Preliminary Safety Evaluation (PSE) describes and analyzes the installation and operation of the Plutonium Stabilization and Packaging System (SPS) at the Plutonium Finishing Plant (PFP). The SPS is a combination of components required to expedite the safe and timely storage of Plutonium (Pu) oxide. The SPS program will receive site Pu packages, process the Pu for storage, package the Pu into metallic containers, and safely store the containers in a specially modified storage vault. The location of the SPS will be in the 2736- ZB building and the storage vaults will be in the 2736-Z building of the PFP, as shown in Figure 1-1. The SPS will produce storage canisters that are larger than those currently used for Pu storage at the PFP. Therefore, the existing storage areas within the PFP secure vaults will require modification. Other modifications will be performed on the 2736-ZB building complex to facilitate the installation and operation of the SPS.

  20. Safety System for Controlling Fluid Flow into a Suction Line (United States)

    England, John Dwight (Inventor); Kelley, Anthony R. (Inventor); Cronise, Raymond J. (Inventor)


    A safety system includes a sleeve fitted within a pool's suction line at the inlet thereof. An open end of the sleeve is approximately aligned with the suction line's inlet. The sleeve terminates with a plate that resides within the suction line. The plate has holes formed therethrough. A housing defining a plurality of distinct channels is fitted in the sleeve so that the distinct channels lie within the sleeve. Each of the distinct channels has a first opening on one end thereof and a second opening on another end thereof. The second openings reside in the sleeve. Each of the distinct channels is at least approximately three feet in length. The first openings are in fluid communication with the water in the pool, and are distributed around a periphery of an area of the housing that prevents coverage of all the first openings when a human interacts therewith.

  1. Safety implications of control systems program at ORNL

    Energy Technology Data Exchange (ETDEWEB)

    Smith, O.L.


    Simulations of two PWRs point to several conclusions that bear on the principle interests of Unresolved Safety Issue A-47: (1) The simulated control systems of both plants exhibit considerable ability to respond to the investigated classes of off-normal disturbances. (2) Overfill of the steam generators usually produced only minor cooling of the primary side. (3) Despite protective features, substantial amounts of water could be injected into the steam lines because of low steam quality or high water level. Whether this creates the potential for water-hammer damage or other mass or momentum effects requires further analysis. (4) Potential core-uncovery scenarios explored steam generator tube rupture and other small breaks that might lead to loss of primary inventory without actuation of high pressure injection. The results indicated situations in which automatic actuation of high pressure injection would terminate the leak and others in which operator intervention appeared necessary. 19 figs.

  2. 23 CFR 973.212 - Indian lands safety management system (SMS). (United States)


    ... 23 Highways 1 2010-04-01 2010-04-01 false Indian lands safety management system (SMS). 973.212... HIGHWAYS MANAGEMENT SYSTEMS PERTAINING TO THE BUREAU OF INDIAN AFFAIRS AND THE INDIAN RESERVATION ROADS PROGRAM Bureau of Indian Affairs Management Systems § 973.212 Indian lands safety management system (SMS...

  3. Nitric Acid Revamp and Upgrading of the Alarm & Protection Safety System at Petrokemija, Croatia

    Directory of Open Access Journals (Sweden)

    Hoško, I.


    Full Text Available Every industrial production, particularly chemical processing, demands special attention in conducting the technological process with regard to the security requirements. For this reason, production processes should be continuously monitored by means of control and alarm safety instrumented systems. In the production of nitric acid at Petrokemija d. d., the original alarm safety system was designed as a combination of an electrical relay safety system and transistorized alarm module system. In order to increase safety requirements and modernize the technological process of nitric acid production, revamping and upgrading of the existing alarm safety system was initiated with a new microprocessor system. The newly derived alarm safety system, Simatic PCS 7, links the function of "classically" distributed control (DCS and logical systems in a common hardware and software platform with integrated engineering tools and operator interface to meet the minimum safety standards with safety integrity level 2 (SIL2 up to level 3 (SIL3, according to IEC 61508 and IEC 61511. This professional paper demonstrates the methodology of upgrading the logic of the alarm safety system in the production of nitric acid in the form of a logical diagram, which was the basis for a further step in its design and construction. Based on the mentioned logical diagram and defined security requirements, the project was implemented in three phases: analysis and testing, installation of the safety equipment and system, and commissioning. Developed also was a verification system of all safety conditions, which could be applied to other facilities for production of nitric acid. With the revamped and upgraded interlock alarm safety system, a new and improved safety boundary in the production of nitric acid was set, which created the foundation for further improvement of the production process in terms of improved analysis.

  4. Safety equipment list for the light duty utility arm system

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, G.A.


    The initial issue (Revision 0) of this Safety Equipment List (SEL) for the Light Duty Utility Arm (LDUA) requires an explanation for both its existence and its being what it is. All LDUA documentation leading up to creation of this SEL, and the SEL itself, is predicated on the LDUA only being approved for use in waste tanks designated as Facility Group 3, i.e., it is not approved for use in Facility Group 1 or 2 waste tanks. Facility Group 3 tanks are those in which a spontaneous or induced hydrogen gas release would be small, localized, and would not exceed 25% of the LFL when mixed with the remaining air volume in the dome space; exceeding these parameters is considered unlikely. Thus, from a NFPA flammable gas environment perspective the waste tank interior is not classified as a hazardous location. Furthermore, a hazards identification and evaluation (HNF-SD-WM-HIE-010, REV 0) performed for the LDUA system concluded that the consequences of actual LDUA system postulated accidents in Flammable Gas Facility Group 3 waste tanks would have either NO IMPACT or LOW IMPACT on the offsite public and onsite worker. Therefore, from a flammable gas perspective, there is not a rationale for classifying any of SSCs associated with the LDUA as either Safety Class (SC) or Safety Significant (SS) SSCs, which, by default, categorizes them as General Service (GS) SSCs. It follows then, based on current PHMC procedures (HNF-PRO-704 and HNF-IP-0842, Vol IV, Section 5.2) for SEL creation and content, and from a flammable gas perspective, that an SEL is NOT REQ@D HOWEVER!!! There is both a precedent and a prudency to capture all SSCS, which although GS, contribute to a Defense-In-Depth (DID) approach to the design and use of equipment in potentially flammable gas environments. This Revision 0 of the LDUA SEL has been created to capture these SSCs and they are designated as GS-DID in this document. The specific reasons for doing this are listed.

  5. Overview of Risk Mitigation for Safety-Critical Computer-Based Systems (United States)

    Torres-Pomales, Wilfredo


    This report presents a high-level overview of a general strategy to mitigate the risks from threats to safety-critical computer-based systems. In this context, a safety threat is a process or phenomenon that can cause operational safety hazards in the form of computational system failures. This report is intended to provide insight into the safety-risk mitigation problem and the characteristics of potential solutions. The limitations of the general risk mitigation strategy are discussed and some options to overcome these limitations are provided. This work is part of an ongoing effort to enable well-founded assurance of safety-related properties of complex safety-critical computer-based aircraft systems by developing an effective capability to model and reason about the safety implications of system requirements and design.

  6. The Art World's Concept of Negative Space Applied to System Safety Management (United States)

    Goodin, James Ronald (Ronnie)


    Tools from several different disciplines can improve system safety management. This paper relates the Art World with our system safety world, showing useful art schools of thought applied to system safety management, developing an art theory-system safety bridge. This bridge is then used to demonstrate relations with risk management, the legal system, personnel management and basic management (establishing priorities). One goal of this presentation/paper is simply to be a fun diversion from the many technical topics presented during the conference.

  7. 75 FR 12123 - Federal Motor Vehicle Safety Standards; Side Impact Protection; Fuel System Integrity; Electric... (United States)


    ... National Highway Traffic Safety Administration 49 CFR Part 571 RIN 2127-AK48 Federal Motor Vehicle Safety Standards; Side Impact Protection; Fuel System Integrity; Electric-Powered Vehicles: Electrolyte Spillage and Electrical Shock Protection AGENCY: National Highway Traffic Safety Administration (NHTSA...

  8. A Microbial Assessment Scheme to measure microbial performance of Food Safety Management Systems

    NARCIS (Netherlands)

    Jacxsens, L.; Kussaga, J.; Luning, P.A.; Spiegel, van der M.; Devlieghere, F.; Uyttendaele, M.


    A Food Safety Management System (FSMS) implemented in a food processing industry is based on Good Hygienic Practices (GHP), Hazard Analysis Critical Control Point (HACCP) principles and should address both food safety control and assurance activities in order to guarantee food safety. One of the

  9. 76 FR 5296 - Safety Management System for Part 121 Certificate Holders; Extension of Comment Period (United States)


    ... and provide meaningful comment to Notice No. 10-15. The Airline Safety and Federal Aviation Extension... Federal Aviation Administration 14 CFR Parts 5 and 119 RIN 2120-AJ86 Safety Management System for Part 121... require each certificate holder operating under 14 CFR part 121 to develop and implement a safety...

  10. Information system equality for food security--implementation of the food safety control system in Taiwan. (United States)

    Chen, Shaun C; Hsu, Guoo-Shyng Wang; Chiu, Chihwei P


    Food security plays a central role in governing agricultural policies in Taiwan. In addition to overuse or the illegal use of pesticide, meat leanness promoters, animal drugs and melamine in the food supply; as well as foodborne illness draws the greatest public concern due to incidents that occur every year in Taiwan. The present report demonstrates the implementation of a food safety control system in Taiwan. In order to control foodborne outbreaks effectively, the central government of the Department of Health of Taiwan launched the food safety control system which includes both the good hygienic practice (GHP) and the HACCP plan, in the last decade. From 1998 to the present, 302 food affiliations that implemented the system have been validated and accredited by a well-established audit system. The implementation of a food safety control system in compliance with international standards is of crucial importance to ensure complete safety and the high quality of foods, not only for domestic markets, but also for international trade.

  11. Safety Psychology Applicating on Coal Mine Safety Management Based on Information System (United States)

    Hou, Baoyue; Chen, Fei

    In recent years, with the increase of intensity of coal mining, a great number of major accidents happen frequently, the reason mostly due to human factors, but human's unsafely behavior are affected by insecurity mental control. In order to reduce accidents, and to improve safety management, with the help of application security psychology, we analyse the cause of insecurity psychological factors from human perception, from personality development, from motivation incentive, from reward and punishment mechanism, and from security aspects of mental training , and put forward countermeasures to promote coal mine safety production,and to provide information for coal mining to improve the level of safety management.

  12. Reference to the Safety Engineering Undergraduate Courses to Improve the Subjects and Contents of the Certified Safety Engineer Qualification and Examination System of China


    Haibin Qiu; Shanghong Shi; Tingdi Zhao; Yiwei Qiao; Jiangshi Zhang


    The aim of this paper is to recommend that the subjects and contents of certified safety engineers use safety engineering undergraduate curriculum system for reference. Human resources play an important role in accident prevention and loss control. Education on safety engineering develops quickly in China. Moreover, the State Administration of Work Safety and the National Human Resources and Social Security Ministry have implemented a certified safety engineer qualification and examination sy...


    Directory of Open Access Journals (Sweden)

    Peter Zajác


    Full Text Available In work is presented verification of food safety management system of deep frozen food. Main emphasis is on creating set of verification questions within articles of standard STN EN ISO 22000:2006 and on searching of effectiveness in food safety management system. Information were acquired from scientific literature sources and they pointed out importance of implementation and upkeep of effective food safety management system. doi:10.5219/28


    Directory of Open Access Journals (Sweden)

    Sadayuki TSUGAWA


    Full Text Available This paper surveys the research on the applications of inter-vehicle communications, the issues of the deployment and technology, and the current status of inter-vehicle communications projects in Europe, the United States and Japan. The inter-vehicle communications, defined here as communications between on-board ITS computers, improve road traffic safety and efficiency by expanding the horizon of the drivers and on-board sensors. One of the earliest studies on inter-vehicle communications began in Japan in the early 1980s. The inter-vehicle communications play an essential role in automated platooning and cooperative driving systems developed since the 1990's by enabling vehicles to obtain data that would be difficult or impossible to measure with on-board sensors. During these years, interest in applications for inter-vehicle communications increased in the EU, the US and Japan, resulting in many national vehicle safety communications projects such as CarTALK2000 in the EU and VSCC in the US. The technological issues include protocol and communications media. Experiments employ various kinds of protocols and typically use infrared, microwave or millimeter wave media. The situation is ready for standardization. The deployment strategy is another issue. To be feasible, deployment should begin with multiple rather than single services that would work even at a low penetration rate of the communication equipment. In addition, non-technological, legal and institutional issues remained unsolved. Although inter-vehicle communications involve many issues, such applications should be promoted because they will lead to safer and more efficient automobile traffic.

  15. Development of Non-safety System Architecture and Evaluation of Components/Systems

    Energy Technology Data Exchange (ETDEWEB)

    Oh, I. S.; Lee, C. K.; Kim, D. H.; Lee, J. W.; Lee, D. Y.; Park, W. M.; Hwang, I. K.; Hur, S.; Kim, J. T.; Park, J. C.; Lee, J. W


    We describe in this report the works performed for a technical evaluation of the non-safety digital control system of the KNICS, the non-safety process control system of the KNICS, a communication load analysis for the MMIS (including both the non-safety and the safety systems) of the KNICS, the development of MMI and an implementation of the logic for the CVCS, and the works performed to support writing a proposal needed for bidding an I and C system based on the KNICS. The technical evaluation results were aimed to be used by the designers to detect parts needed to be corrected or to be newly inserted, and also by the developers during the development phase. The requirement specifications and the data requirement characteristics have been identified for each subsystem of the determined KNICS structure. For each communication node, the specifications related to the data transfer including the data capacity for interfaces, delay time for the data transfer, and the marginal availability of its performance capabilities have been analyzed to identify the amount of data transfer and hence to verify that both of the designed structures for the safety related communications network and for the digital communications network are appropriate. The results of the supporting work performed for writing the technical specifications related to each subsystem of the KNICS structure, are expected to be useful in writing a proposal for the expected Uljin new units 1 and 2, and in the I and C upgrade for any of the existing nuclear power plants under operation. Also included in this report are the descriptions on a design of the chemical volume control system (CVCS), on the supporting work performed to draw the logic diagrams for CVCS using the tool ISaGRAF, and on the generation of a set of system displays to be used as references.

  16. 78 FR 66420 - Proposed Enhancements to the Motor Carrier Safety Measurement System (SMS) Public Web Site (United States)


    ..., the SMS provides the motor carrier industry and other safety stakeholders with more comprehensive... and Fitness Electronic Records System (SAFER) Web site. Displaying current insurance and authority...

  17. Analysis of Aviation Safety Reporting System Incident Data Associated with the Technical Challenges of the System-Wide Safety and Assurance Technologies Project (United States)

    Withrow, Colleen A.; Reveley, Mary S.


    The Aviation Safety Program (AvSP) System-Wide Safety and Assurance Technologies (SSAT) Project asked the AvSP Systems and Portfolio Analysis Team to identify SSAT-related trends. SSAT had four technical challenges: advance safety assurance to enable deployment of NextGen systems; automated discovery of precursors to aviation safety incidents; increasing safety of human-automation interaction by incorporating human performance, and prognostic algorithm design for safety assurance. This report reviews incident data from the NASA Aviation Safety Reporting System (ASRS) for system-component-failure- or-malfunction- (SCFM-) related and human-factor-related incidents for commercial or cargo air carriers (Part 121), commuter airlines (Part 135), and general aviation (Part 91). The data was analyzed by Federal Aviation Regulations (FAR) part, phase of flight, SCFM category, human factor category, and a variety of anomalies and results. There were 38 894 SCFM-related incidents and 83 478 human-factorrelated incidents analyzed between January 1993 and April 2011.

  18. Safety design integrated in the Building Delivery System

    DEFF Research Database (Denmark)

    Jørgensen, Kirsten


    It is important to see safety and health in construction as an integrated part of the way in which designers, architects, constructors, engineers and others carry out their consulting services. The purpose of this article is to demonstrate how safety and health can be integrated in the design...... of safety in each process. The group of participants who created the description had a high experience in a combination of research, safety and health in general and especial in construction and knowledge of the lean construction processes both from the clients perspective as well as from the designers...

  19. 14 CFR 415.127 - Flight safety system design and operation data. (United States)


    ... expendable launch vehicle that uses a flight safety system to protect public safety as required by § 417.107... and connections and wiring diagrams and schematics. For a flight termination system, a description of... document must also contain flight termination system wiring diagrams and schematics and identify the test...

  20. A new safety support system for wandering elderly persons. (United States)

    Matsuoka, Shingo; Ogawa, Hidekuni; Maki, Hiromichi; Yonezawa, Yoshiharu; Caldwell, W Morton


    We have developed a new mobile phone-based safety support system for transmitting information of a wandering elderly person's location and the environmental sounds around that person. The system consists of a wearable sensor and a conventional desktop PC with Internet access acting as the server computer. The wearable sensor, which is attached behind the neck of the elderly person's shirt, is composed of a low transmitting power mobile phone (W-SIM), a small microphone and a one chip microcontroller. The wandering elderly person's location is identified within 100 m from the mobile phone company's antenna ID via the W-SIM. The caregiver sets the elderly person's movement area by specialized computer software. When the elderly person goes out of the area, the sensor automatically records the environmental sound around the wandering elderly person for the presumption of the person's situation with the small microphone. The W-SIM sends both the wandering elderly person's location and the environmental sound to the server computer. The server computer informs automatically the caregiver by the e-mail. The caregiver can monitor the sound and the map of the wandering person's location via Internet. The sound enables the presumption of an accurate location and the situation of the wandering elderly person.

  1. A Real-Time Embedded Blind Spot Safety Assistance System

    Directory of Open Access Journals (Sweden)

    Bing-Fei Wu


    Full Text Available This paper presents an effective vehicle and motorcycle detection system in the blind spot area in the daytime and nighttime scenes. The proposed method identifies vehicle and motorcycle by detecting the shadow and the edge features in the daytime, and the vehicle and motorcycle could be detected through locating the headlights at nighttime. First, shadow segmentation is performed to briefly locate the position of the vehicle. Then, the vertical and horizontal edges are utilized to verify the existence of the vehicle. After that, tracking procedure is operated to track the same vehicle in the consecutive frames. Finally, the driving behavior is judged by the trajectory. Second, the lamps in the nighttime are extracted based on automatic histogram thresholding, and are verified by spatial and temporal features to against the reflection of the pavement. The proposed real-time vision-based Blind Spot Safety-Assistance System has implemented and evaluated on a TI DM6437 platform to perform the vehicle detection on real highway, expressways, and urban roadways, and works well on sunny, cloudy, and rainy conditions in daytime and night time. Experimental results demonstrate that the proposed vehicle detection approach is effective and feasible in various environments.

  2. Safety evaluation of a Medical Device Data System. (United States)

    Liddle, Stephanie; Grover, Lata; Zhang, Rachel; Khitrov, Maxim; Brown, Joan C; Cobb, J Perren; Goldman, Julian; Chou, Joseph; Yagoda, Daniel; Westover, Brandon; Reisner, Andrew T


    Our hospital became interested in the extraction of electronic data from our bedside monitor network to enrich clinical care, and enable various quality improvement projects, research projects, and future applications involving advanced decision-support. We conducted a range of tests to confirm the safety of deploying BedMaster (Excel Medical Electronics, Jupiter FL, USA), which is third-party software sold expressly to provide electronic data extraction and storage from networked General Electric Healthcare bedside patient monitors. We conducted a series of tests examining the changes in network performance when the BedMaster system was on our isolated patient monitor network. We found that use of BedMaster led to measurable, but trivial increases in network traffic and latency. We did not identify any failure scenarios in our analysis and testing. The major value of this report is to highlight potential challenges inherent in data and electronic device integration within the healthcare setting. In describing our strategy for testing the BedMaster system, it is our intention to present one testing protocol and to generate thought and discussion in the broader community about what types of problems can arise with inter-operability, and what types of testing are necessary to mitigate against these risks. Standards for inter-operability would surely reduce the inherent risks.

  3. Human-System Safety Methods for Development of Advanced Air Traffic Management Systems

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, W.R.


    The Idaho National Engineering and Environmental Laboratory (INEEL) is supporting the National Aeronautics and Space Administration in the development of advanced air traffic management (ATM) systems as part of the Advanced Air Transportation Technologies program. As part of this program INEEL conducted a survey of human-system safety methods that have been applied to complex technical systems, to identify lessons learned from these applications and provide recommendations for the development of advanced ATM systems. The domains that were surveyed included offshore oil and gas, commercial nuclear power, commercial aviation, and military. The survey showed that widely different approaches are used in these industries, and that the methods used range from very high-level, qualitative approaches to very detailed quantitative methods such as human reliability analysis (HRA) and probabilistic safety assessment (PSA). In addition, the industries varied widely in how effectively they incorporate human-system safety assessment in the design, development, and testing of complex technical systems. In spite of the lack of uniformity in the approaches and methods used, it was found that methods are available that can be combined and adapted to support the development of advanced air traffic management systems.

  4. Human-system safety methods for development of advanced air traffic management systems

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, William R. [Idaho National Engineering and Environmental Laboratory, Idaho Falls (United States)


    The Idaho National Engineering and Environmental Laboratory (INEEL) is supporting the National Aeronautics and Space Administration in the development of advanced air traffic management (ATM) systems as part of the Advanced Air Transportation Technologies program. As part of this program INEEL conducted a survey of human-system safety methods that have been applied to complex technical systems, to identify lessons learned from these applications and provide recommendations for the development of advanced ATM systems. The domains that were surveyed included offshore oil and gas, commercial nuclear power, commercial aviation, and military. The survey showed that widely different approaches are used in these industries, and that the methods used range from very high-level, qualitative approaches to very detailed quantitative methods such as human reliability analysis (HRA) and probabilistic safety assessment (PSA). In addition, the industries varied widely in how effectively they incorporate human-system safety assessment in the design, development, and testing of complex technical systems. In spite of the lack of uniformity in the approaches and methods used, it was found that methods are available that can be combined and adapted to support the development of advanced air traffic management systems (author) (ml)

  5. Operation safety of complex industrial systems. Main concepts; Surete de fonctionnement des systemes industriels complexes. Principaux concepts

    Energy Technology Data Exchange (ETDEWEB)

    Zwingelstein, G


    Operation safety consists in knowing, evaluating, foreseeing, measuring and mastering the technological system and human failures in order to avoid their impacts on health and people's safety, on productivity, and on the environment, and to preserve the Earth's resources. This article recalls the main concepts of operation safety: 1 - evolutions in the domain; 2 - failures, missions and functions of a system and of its components: functional failure, missions and functions, industrial processes, notions of probability; 3 - basic concepts and operation safety: reliability, unreliability, failure density, failure rate, relations between them, availability, maintainability, safety. (J.S.)

  6. Research on safety analysis for airborne system based on extended functional model

    Directory of Open Access Journals (Sweden)

    Quan Jiang


    Full Text Available With the widespread use of embedded system in safety critical areas, system safety assurance has become one of the research hotspots of engineering technologies. System safety analysis mainly concentrates on the requirement specification and the recent design, and in the process of the actual development of the software, safety requirement analysis and design are two independent processes. This article expands the safety requirements described by fault tree into state diagram and proposes the new concept “fault state diagram,” which can unify safety requirement model and functional model. Based on the fault state diagram, this article proposes the method of airborne system safety analysis, including the following: gives out one method for abstracting and describing safety requirements from system fault tree based on Backus Normal Form; defines the transformation rules from fault tree logic gates and continuous time into state diagram elements; designs safety requirement information mapping table which translates safety requirements into state diagram elements; and designs the automatic construction algorithm of fault state diagram, which is based on the transformation rules and mapping table. Finally, a small gas stove control system case using the method proves the feasibility and effectiveness of the proposed method.

  7. Firefighter safety for PV systems: Overview of future requirements and protection systems

    DEFF Research Database (Denmark)

    Spataru, Sergiu; Sera, Dezso; Blaabjerg, Frede


    An important and highly discussed safety issue for photovoltaic systems is that, as long as they are illuminated, a high voltage is present at the PV string terminals and cables between the string and inverters, independent of the state of the inverter's dc disconnection switch, which poses a risk...... shutdown procedures. This paper gives an overview on the most recent fire - and firefighter safety requirements for PV systems, with focus on system and module shutdown systems. Several solutions are presented, analyzed and compared by considering a number of essential characteristics, including...... for operators during maintenance or fire-fighting. One of the solutions is individual module shutdown by short-circuiting or disconnecting each PV module from the PV string. However, currently no standards have been adopted either for implementing or testing these methods, or doing an evaluation of the module...

  8. The US drug safety system: role of the pharmaceutical industry. (United States)

    Gibson, Brent R; Suh, Ryung; Tilson, Hugh


    Despite increasingly strident calls for improved drug safety in the United States, recent events underscore the continuing gap among manufacturers, regulators, patients, and physicians. In the period leading to the recent Institute of Medicine report on the future of drug safety, representatives from industry were given an opportunity to provide input into this report. In light of continuing concerns about drug safety and pending legislation, this original perspective provides an important context. This work consolidates the views of representatives of individual pharmaceutical companies; the large industry trade associations, the Pharmaceutical Researchers and Manufacturers of America (PhRMA) and the Biotechnology Industry Association (BIO); and those of the authors with regard to the industry role of drug safety in the United States. To ensure continued protection of the public's health, manufacturers must recognize themselves as critical to ensuring safe products; maintain corporate safety functions separate from marketing functions; provide oversight by a senior medical executive; engage in structured epidemiological research, risk assessment, and risk communication; and mandate the formation and maintenance of an internal, interdisciplinary, senior level safety council. The importance of aggressive and accountable drug safety will only become more salient as the public and their elected representatives demand better accountability from industry. Individual corporations now have the opportunity to move first to counter perceptions of profit over safety and to ensure that their business practices adequately protect the public's health. Copyright 2007 John Wiley & Sons, Ltd.

  9. 75 FR 62008 - Safety Management System for Certificated Airports (United States)


    ...) defines SMS as a ``systematic approach to managing safety, including the necessary organizational... airports hosting air carrier operations. An SMS is a formalized approach to managing safety by developing... will post all comments we receive, without change, to , including any...


    Directory of Open Access Journals (Sweden)

    Piotr Kafel


    Full Text Available The purpose of this paper is to analyze the place of occupational health and safety management system (OHSMS within the integrated management system. Implementation aspects of management systems are discussed, namely the different management system standards used for registration, for example ISO 14001, ISO 9001, OHSAS 18001, ISO 27001, the order in which they were implemented, the time required for each implementation, as well as the scope of integration of these management system standards into a single Integrated Management System and the level of integration. In order to do so, some of the results of a survey carried out in 81 organizations registered to at least two management systems selected from popular international standards, e.g.: ISO 9001, ISO 14001, OHSAS 18001, ISO/IEC 27001, ISO 22000 were used. OHSMS is not the system that is implemented as a first one. Usually it is implemented after or simultaneously with ISO 9001 and ISO 14001 standards. Time of implementation of MSSs in second and further round of implementation is shorter than during the implementation of first standards. There is a higher level of integration of implemented management standards in organizations where one of the standards in OHSMS, than in a companies without OHSMS. The paper analyses those sequences of management systems implementation of safety management systems with other system, that allow organizations to achieve higher levels of integration and presents a possible pattern for the companies initiating the integration process.

  11. Research on public participant urban infrastructure safety monitoring system using smartphone (United States)

    Zhao, Xuefeng; Wang, Niannian; Ou, Jinping; Yu, Yan; Li, Mingchu


    Currently more and more people concerned about the safety of major public security. Public participant urban infrastructure safety monitoring and investigation has become a trend in the era of big data. In this paper, public participant urban infrastructure safety protection system based on smart phones is proposed. The system makes it possible to public participant disaster data collection, monitoring and emergency evaluation in the field of disaster prevention and mitigation. Function of the system is to monitor the structural acceleration, angle and other vibration information, and extract structural deformation and implement disaster emergency communications based on smartphone without network. The monitoring data is uploaded to the website to create urban safety information database. Then the system supports big data analysis processing, the structure safety assessment and city safety early warning.

  12. Handbook of driver assistance systems basic information, components and systems for active safety and comfort

    CERN Document Server

    Hakuli, Stephan; Lotz, Felix; Singer, Christina


    This fundamental work explains in detail systems for active safety and driver assistance, considering both their structure and their function. These include the well-known standard systems such as Anti-lock braking system (ABS), Electronic Stability Control (ESC) or Adaptive Cruise Control (ACC). But it includes also new systems for protecting collisions protection, for changing the lane, or for convenient parking. The book aims at giving a complete picture focusing on the entire system. First, it describes the components which are necessary for assistance systems, such as sensors, actuators, mechatronic subsystems, and control elements. Then, it explains key features for the user-friendly design of human-machine interfaces between driver and assistance system. Finally, important characteristic features of driver assistance systems for particular vehicles are presented: Systems for commercial vehicles and motorcycles.

  13. Vaccine safety monitoring systems in developing countries: an example of the Vietnam model. (United States)

    Ali, Mohammad; Rath, Barbara; Thiem, Vu Dinh


    Only few health intervention programs have been as successful as vaccination programs with respect to preventing morbidity and mortality in developing countries. However, the success of a vaccination program is threatened by rumors and misunderstanding about the risks of vaccines. It is short-sighted to plan the introduction of vaccines into developing countries unless effective vaccine safety monitoring systems are in place. Such systems that track adverse events following immunization (AEFI) is currently lacking in most developing countries. Therefore, any rumor may affect the entire vaccination program. Public health authorities should implement the safety monitoring system of vaccines, and disseminate safety issues in a proactive mode. Effective safety surveillance systems should allow for the conduct of both traditional and alternative epidemiologic studies through the use of prospective data sets. The vaccine safety data link implemented in Vietnam in mid-2002 indicates that it is feasible to establish a vaccine safety monitoring system for the communication of vaccine safety in developing countries. The data link provided the investigators an opportunity to evaluate AEFI related to measles vaccine. Implementing such vaccine safety monitoring system is useful in all developing countries. The system should be able to make objective and clear communication regarding safety issues of vaccines, and the data should be reported to the public on a regular basis for maintaining their confidence in vaccination programs.

  14. Developing and Testing the Health Care Safety Hotline: A Prototype Consumer Reporting System for Patient Safety Events. (United States)

    Schneider, Eric C; Ridgely, M Susan; Quigley, Denise D; Hunter, Lauren E; Leuschner, Kristin J; Weingart, Saul N; Weissman, Joel S; Zimmer, Karen P; Giannini, Robert C


    This article describes the design, development, and testing of the Health Care Safety Hotline, a prototype consumer reporting system for patient safety events. The prototype was designed and developed with ongoing review by a technical expert panel and feedback obtained during a public comment period. Two health care delivery organizations in one metropolitan area collaborated with the researchers to demonstrate and evaluate the system. The prototype was deployed and elicited information from patients, family members, and caregivers through a website or an 800 phone number. The reports were considered useful and had little overlap with information received by the health care organizations through their usual risk management, customer service, and patient safety monitoring systems. However, the frequency of reporting was lower than anticipated, suggesting that further refinements, including efforts to raise awareness by actively soliciting reports from subjects, might be necessary to substantially increase the volume of useful reports. It is possible that a single technology platform could be built to meet a variety of different patient safety objectives, but it may not be possible to achieve several objectives simultaneously through a single consumer reporting system while also establishing trust with patients, caregivers, and providers.

  15. [Role of reporting and learning systems in the improvement of patient safety]. (United States)

    Lám, Judit; Sümegi, Viktória; Surján, Cecília; Kullmann, Lajos; Belicza, Éva


    The principles and requirements of a patient safety related reporting and learning system were defined by the World Health Organization Draft Guidelines for Adverse Event Reporting and Learning Systems published in 2005. Since then more and more Hungarian health care organizations aim to improve their patient safety culture. In order to support this goal the NEVES reporting and learning system and the series of Patient Safety Forums for training and consultation were launched in 2006 and significantly renewed recently. Current operative modifications to the Health Law emphasize patient safety, making the introduction of these programs once again necessary.

  16. Design considerations in an active medical product safety monitoring system. (United States)

    Gagne, Joshua J; Fireman, Bruce; Ryan, Patrick B; Maclure, Malcolm; Gerhard, Tobias; Toh, Sengwee; Rassen, Jeremy A; Nelson, Jennifer C; Schneeweiss, Sebastian


    Active medical product monitoring systems, such as the Sentinel System, will utilize electronic healthcare data captured during routine health care. Safety signals that arise from these data may be spurious because of chance or bias, particularly confounding bias, given the observational nature of the data. Applying appropriate monitoring designs can filter out many false-positive and false-negative associations from the outset. Designs can be classified by whether they produce estimates based on between-person or within-person comparisons. In deciding which approach is more suitable for a given monitoring scenario, stakeholders must consider the characteristics of the monitored product, characteristics of the health outcome of interest (HOI), and characteristics of the potential link between these. Specifically, three factors drive design decisions: (i) strength of within-person and between-person confounding; (ii) whether circumstances exist that may predispose to misclassification of exposure or misclassification of the timing of the HOI; and (iii) whether the exposure of interest is predominantly transient or sustained. Additional design considerations include whether to focus on new users, the availability of appropriate active comparators, the presence of an exposure time trend, and the measure of association of interest. When the key assumptions of self-controlled designs are fulfilled (i.e., lack of within-person, time-varying confounding; abrupt HOI onset; and transient exposure), within-person comparisons are preferred because they inherently avoid confounding by fixed factors. The cohort approach generally is preferred in other situations and particularly when timing of exposure or outcome is uncertain because cohort approaches are less vulnerable to biases resulting from misclassification. Copyright © 2012 John Wiley & Sons, Ltd.

  17. Hearing protection: Surpassing the limits to attenuation imposed by the bone-conduction pathways (United States)

    Berger, Elliott H.; Kieper, Ronald W.; Gauger, Dan


    With louder and louder weapon systems being developed and military personnel being exposed to steady noise levels approaching and sometimes exceeding 150 dB, a growing interest in greater amounts of hearing protection is evident. When the need for communications is included in the equation, the situation is even more extreme. New initiatives are underway to design improved hearing protection, including active noise reduction (ANR) earplugs and perhaps even active cancellation of head-borne vibration. With that in mind it may be useful to explore the limits to attenuation, and whether they can be approached with existing technology. Data on the noise reduction achievable with high-attenuation foam earplugs, as a function of insertion depth, will be reported. Previous studies will be reviewed that provide indications of the bone-conduction (BC) limits to attenuation that, in terms of mean values, range from 40 to 60 dB across the frequencies from 125 Hz to 8 kHz. Additionally, new research on the effects of a flight helmet on the BC limits, as well as the potential attenuation from deeply inserted passive foam earplugs, worn with passive earmuffs, or with active-noise reduction (ANR) earmuffs, will be examined. The data demonstrate that gains in attenuation exceeding 10 dB above the head-not-covered limits can be achieved if the head is effectively shielded from acoustical stimulation.

  18. Development of new safety devices for mine hoisting systems

    Energy Technology Data Exchange (ETDEWEB)

    Rowe, P.G. [Hardcastle & Richards Proprietary Ltd., Perth, WA (Australia)


    The only safety device currently in common use to prevent a cage load of men falling to the shaft bottom after a broken rope or attachment is safety grippers for use on wooden guides, and these are not considered entirely satisfactory. The paper describes a concept for a safety device that, in the event of a broken rope, will attach itself to either rope guides or steel guides in the shaft, and bring the cage to rest at a controlled rate of deceleration. Successful initial testwork has been completed on a simple form of restrainer which applies the controlled deceleration force through a wire rope suspension sling. 1 ref., 3 figs.

  19. Carbon reduction in the real world: how the UK will surpass its Kyoto obligations

    Energy Technology Data Exchange (ETDEWEB)

    Eyre, Nick [Energy Saving Trust, London (United Kingdom)


    Carbon dioxide emissions from UK energy use have fallen by more than 20% over the last 30 years, and carbon intensity --- carbon emissions per unit of GDP --- has halved. These reductions have been achieved by a combination of decarbonisation of the energy system and substantial improvements in energy efficiency. Use of natural gas in power generation has been a big factor in recent years, but energy efficiency improvements in households and particularly industry have been more important over a longer period. Government policies designed primarily to address climate change have not been important contributors, until recently. Future reductions in emissions will require more proactive policies. However, they are possible without any economic difficulties, notably by adopting cost-effective energy efficiency measures, using new renewable energy sources and reducing dependence on private cars. These policies will improve economic efficiency. The new UK Climate Change Programme includes policies that combine regulation, investment, fiscal measures and other economic instruments. By working with the grain of other social, environmental and economic policies, they can achieve far more than a carbon tax alone, set at any politically acceptable level. Modelling the costs of emission reductions using a carbon tax as the only instrument would not only massively over-estimate costs, it would bear little resemblance to real world politics. The paper demonstrates that a more diverse set of policy instruments is likely to be an effective and politically acceptable approach in a mature industrial economy. It is concluded that the UK's Kyoto target of a 12.5% reduction in greenhouse gas emissions is not challenging. The UK Government's target of reducing carbon dioxide emissions by 20% between 1990 and 2010 is also achievable. By 2010 per capita emissions from the UK will be well below 2.5tC per year. Claims that some countries, notably the USA, could not reduce per

  20. Overall System Description and Safety Characteristics of Prototype Gen IV Sodium Cooled Fast Reactor in Korea

    Directory of Open Access Journals (Sweden)

    Jaewoon Yoo


    Full Text Available The Prototype Gen IV sodium cooled fast reactor (PGSFR has been developed for the last 4 years, fulfilling the technology demonstration of the burning capability of transuranic elements included in light water reactor spent nuclear fuel. The PGSFR design has been focused on the robustness of safety systems by enhancing inherent safety characteristics of metal fuel and strengthening passive safety features using natural circulation and thermal expansion. The preliminary safety information document as a major outcome of the first design phase of PGSFR development was issued at the end of 2015. The project entered the second design phase at the beginning of 2016. This paper summarizes the overall structures, systems, and components of nuclear steam supply system and safety characteristics of the PGSFR. The research and development activities to demonstrate the safety performance are also briefly introduced in the paper.


    Energy Technology Data Exchange (ETDEWEB)

    William E. Kastenberg; Edward Blandford; Lance Kim


    This project has developed quantitative safety goals for Generation IV (Gen IV) nuclear energy systems. These safety goals are risk based and technology independent. The foundations for a new approach to risk analysis has been developed, along with a new operational definition of risk. This project has furthered the current state-of-the-art by developing quantitative safety goals for both Gen IV reactors and for the overall Gen IV nuclear fuel cycle. The risk analysis approach developed will quantify performance measures, characterize uncertainty, and address a more comprehensive view of safety as it relates to the overall system. Appropriate safety criteria are necessary to manage risk in a prudent and cost-effective manner. This study is also important for government agencies responsible for managing, reviewing, and for approving advanced reactor systems because they are charged with assuring the health and safety of the public.

  2. Ex-ante assessment of the safety effects of intelligent transport systems. (United States)

    Kulmala, Risto


    There is a need to develop a comprehensive framework for the safety assessment of Intelligent Transport Systems (ITS). This framework should: (1) cover all three dimensions of road safety-exposure, crash risk and consequence, (2) cover, in addition to the engineering effect, also the effects due to behavioural adaptation and (3) be compatible with the other aspects of state of the art road safety theories. A framework based on nine ITS safety mechanisms is proposed and discussed with regard to the requirements set to the framework. In order to illustrate the application of the framework in practice, the paper presents a method based on the framework and the results from applying that method for twelve intelligent vehicle systems in Europe. The framework is also compared to two recent frameworks applied in the safety assessment of intelligent vehicle safety systems. Copyright 2010 Elsevier Ltd. All rights reserved.

  3. Factors affecting the status of food safety management systems in the global fresh produce chain

    NARCIS (Netherlands)

    Kirezieva, K.K.; Luning, P.A.; Jacxsens, L.; Allende, A.; Johannessen, G.S.; Tondo, E.C.; Rajkovicb, A.; Uyttendaele, M.; Boekel, van T.


    Increase in global trade raised questions regarding status of food safety management systems in fresh produce companies, especially from developing and emerging countries. The aim of this study was to investigate the status of food safety management systems (FSMSs) implemented at primary production

  4. Estimating Impact and Frequency of Risks to Safety and Mission Critical Systems Using CVSS

    NARCIS (Netherlands)

    Houmb, S.H.; Nunes Leal Franqueira, V.; Engum, E.A.


    Many safety and mission critical systems depend on the correct and secure operation of both supportive and core software systems. E.g., both the safety of personnel and the effective execution of core missions on an oil platform depend on the correct recording storing, transfer and interpretation of

  5. Design of the NSLS-II Top-Off Safety System

    Energy Technology Data Exchange (ETDEWEB)

    Fliller, III R. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Doom, L. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Ganetis, G. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Hetzel, C. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Job, P. K. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Li, Y. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Shaftan, T. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Sharma, S. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Singh, O. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Wang, G. M. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source; Xia, Z. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source


    The NSLS-II accelerators finished commissioning in the fall of 2014, with beamline commissioning underway. Part of the design for the NSLS-II is to operate in top off mode. The Top Off Safety System (TOSS) is presently being installed. In this report we discuss the Top Off Safety System design and implementation, along with the necessary tracking results and radiological calculations.

  6. 75 FR 68664 - Federal Motor Vehicle Safety Standards; Child Restraint Systems; Booster Seat Effectiveness... (United States)


    ... National Highway Traffic Safety Administration Federal Motor Vehicle Safety Standards; Child Restraint... Standard 213, Child Restraint Systems. The report's title is: Booster Seat ] Effectiveness Estimates Based... standards for child restraint systems, including booster seats, manufactured for use in motor vehicles as...

  7. Creating a highway information system for safety roadway features. (United States)


    Roadway departures are the leading cause of roadside fatalities. The Kentucky Transportation Cabinet (KYTC) has : undertaken a number of roadside safety measures to reduce roadway departures. Specifically, KYTC has installed : several low-cost, syste...

  8. Integration of Safety in the Building Delivery System

    DEFF Research Database (Denmark)

    Jørgensen, Kirsten; Sander, Dag; Staghøj, Aage


    recommended as the most suitable for a construction process, since it ensures that considerations for health and safety at work do not conflict with considerations for economical, efficiency wise, quality wise and architectural objectives. The goal is to have the considerations for health and safety at work...... become a natural part of the construction process and thereby also have them incorporated into the detailed design process. The practical value of the concept depends on how you manage and organise the detailed design process. Keeping health and safety at work in mind through all phases...... of the construction process will ensure due considerations with regard to organisation, demands for the outcome, analysing and fulfilling demands for buildability and thereby incorporating the demands for health and safety at work into the project material....

  9. System principles, mathematical models and methods to ensure high reliability of safety systems (United States)

    Zaslavskyi, V.


    Modern safety and security systems are composed of a large number of various components designed for detection, localization, tracking, collecting, and processing of information from the systems of monitoring, telemetry, control, etc. They are required to be highly reliable in a view to correctly perform data aggregation, processing and analysis for subsequent decision making support. On design and construction phases of the manufacturing of such systems a various types of components (elements, devices, and subsystems) are considered and used to ensure high reliability of signals detection, noise isolation, and erroneous commands reduction. When generating design solutions for highly reliable systems a number of restrictions and conditions such as types of components and various constrains on resources should be considered. Various types of components perform identical functions; however, they are implemented using diverse principles, approaches and have distinct technical and economic indicators such as cost or power consumption. The systematic use of different component types increases the probability of tasks performing and eliminates the common cause failure. We consider type-variety principle as an engineering principle of system analysis, mathematical models based on this principle, and algorithms for solving optimization problems of highly reliable safety and security systems design. Mathematical models are formalized in a class of two-level discrete optimization problems of large dimension. The proposed approach, mathematical models, algorithms can be used for problem solving of optimal redundancy on the basis of a variety of methods and control devices for fault and defects detection in technical systems, telecommunication networks, and energy systems.

  10. Safety impact of an integrated crash warning system based on field test data. (United States)


    This paper provides the results of an analysis : conducted to assess the safety impact of an integrated : vehicle-based crash warning system based on : naturalistic driving data collected from a field : operational test. The system incorporates four ...

  11. Digital System Reliability Test for the Evaluation of safety Critical Software of Digital Reactor Protection System

    Directory of Open Access Journals (Sweden)

    Hyun-Kook Shin


    Full Text Available A new Digital Reactor Protection System (DRPS based on VME bus Single Board Computer has been developed by KOPEC to prevent software Common Mode Failure(CMF inside digital system. The new DRPS has been proved to be an effective digital safety system to prevent CMF by Defense-in-Depth and Diversity (DID&D analysis. However, for practical use in Nuclear Power Plants, the performance test and the reliability test are essential for the digital system qualification. In this study, a single channel of DRPS prototype has been manufactured for the evaluation of DRPS capabilities. The integrated functional tests are performed and the system reliability is analyzed and tested. The results of reliability test show that the application software of DRPS has a very high reliability compared with the analog reactor protection systems.

  12. Scale development of safety management system evaluation for the airline industry. (United States)

    Chen, Ching-Fu; Chen, Shu-Chuan


    The airline industry relies on the implementation of Safety Management System (SMS) to integrate safety policies and augment safety performance at both organizational and individual levels. Although there are various degrees of SMS implementation in practice, a comprehensive scale measuring the essential dimensions of SMS is still lacking. This paper thus aims to develop an SMS measurement scale from the perspective of aviation experts and airline managers to evaluate the performance of company's safety management system, by adopting Schwab's (1980) three-stage scale development procedure. The results reveal a five-factor structure consisting of 23 items. The five factors include documentation and commands, safety promotion and training, executive management commitment, emergency preparedness and response plan and safety management policy. The implications of this SMS evaluation scale for practitioners and future research are discussed. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. Assessing the safety effects of cooperative intelligent transport systems: A bowtie analysis approach. (United States)

    Ehlers, Ute Christine; Ryeng, Eirin Olaussen; McCormack, Edward; Khan, Faisal; Ehlers, Sören


    The safety effects of cooperative intelligent transport systems (C-ITS) are mostly unknown and associated with uncertainties, because these systems represent emerging technology. This study proposes a bowtie analysis as a conceptual framework for evaluating the safety effect of cooperative intelligent transport systems. These seek to prevent road traffic accidents or mitigate their consequences. Under the assumption of the potential occurrence of a particular single vehicle accident, three case studies demonstrate the application of the bowtie analysis approach in road traffic safety. The approach utilizes exemplary expert estimates and knowledge from literature on the probability of the occurrence of accident risk factors and of the success of safety measures. Fuzzy set theory is applied to handle uncertainty in expert knowledge. Based on this approach, a useful tool is developed to estimate the effects of safety-related cooperative intelligent transport systems in terms of the expected change in accident occurrence and consequence probability. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Safety Confirmation System Using Ultrasonic Radar for Elderly People Living Alone (United States)

    Tanaka, Kanya; Uchibori, Akihiko; Haruyama, Kazuo; Nishimura, Yuki; Uchikado, Shigeru; Rahman, Faridah Abd

    In Japan, the number of elderly people living alone has increased in recent years. Therefore, we propose a safety confirmation system that includes an ultrasonic radar for confirming the safety of elderly people living alone. This system consists of an ultrasonic radar, a power line communication unit, and an information processing communication unit. The safety confirmation method performs the human body detection in the restroom using ultrasonic radar. In addition, the proposed system contains a self-checking function. The effectiveness of the proposed system has been confirmed by the results of a field experiment.

  15. The Application of Software Safety to the Constellation Program Launch Control System (United States)

    Kania, James; Hill, Janice


    The application of software safety practices on the LCS project resulted in the successful implementation of the NASA Software Safety Standard NASA-STD-8719.138 and CxP software safety requirements. The GOP-GEN-GSW-011 Hazard Report was the first report developed at KSC to identify software hazard causes and their controls. This approach can be applied to similar large software - intensive systems where loss of control can lead to a hazard.

  16. System safety engineering in the development of advanced surface transportation vehicles (United States)

    Arnzen, H. E.


    Applications of system safety engineering to the development of advanced surface transportation vehicles are described. As a pertinent example, the paper describes a safety engineering efforts tailored to the particular design and test requirements of the Tracked Air Cushion Research Vehicle (TACRV). The test results obtained from this unique research vehicle provide significant design data directly applicable to the development of future tracked air cushion vehicles that will carry passengers in comfort and safety at speeds up to 300 miles per hour.

  17. Aging of safety class 1E transformers in safety systems of nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, E.W.; Edson, J.L.; Udy, A.C. [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States)


    This report discusses aging effects on safety-related power transformers in nuclear power plants. It also evaluates maintenance, testing, and monitoring practices with respect to their effectiveness in detecting and mitigating the effects of aging. The study follows the US Nuclear Regulatory Commission`s (NRC`s) Nuclear Plant-Aging Research approach. It investigates the materials used in transformer construction, identifies stressors and aging mechanisms, presents operating and testing experience with aging effects, analyzes transformer failure events reported in various databases, and evaluates maintenance practices. Databases maintained by the nuclear industry were analyzed to evaluate the effects of aging on the operation of nuclear power plants.

  18. Design of agricultural product quality safety retrospective supervision system of Jiangsu province (United States)

    Wang, Kun


    In store and supermarkets to consumers can trace back agricultural products through the electronic province card to query their origin, planting, processing, packaging, testing and other important information and found that the problems. Quality and safety issues can identify the responsibility of the problem. This paper designs a retroactive supervision system for the quality and safety of agricultural products in Jiangsu Province. Based on the analysis of agricultural production and business process, the goal of Jiangsu agricultural product quality safety traceability system construction is established, and the specific functional requirements and non-functioning requirements of the retroactive system are analyzed, and the target is specified for the specific construction of the retroactive system. The design of the quality and safety traceability system in Jiangsu province contains the design of the overall design, the trace code design and the system function module.

  19. Linking better shiftwork arrangements with safety and health management systems

    Directory of Open Access Journals (Sweden)

    Kazutaka Kogi


    Full Text Available OBJECTIVE: Various support measures useful for promoting joint change approaches to the improvement of both shiftworking arrangements and safety and health management systems were reviewed. A particular focus was placed on enterprise-level risk reduction measures linking working hours and management systems. METHODS: Voluntary industry-based guidelines on night and shift work for department stores and the chemical, automobile and electrical equipment industries were examined. Survey results that had led to the compilation of practicable measures to be included in these guidelines were also examined. The common support measures were then compared with ergonomic checkpoints for plant maintenance work involving irregular nightshifts. On the basis of this analysis, a new night and shift work checklist was designed. RESULTS: Both the guidelines and the plant maintenance work checkpoints were found to commonly cover multiple issues including work schedules and various job-related risks. This close link between shiftwork arrangements and risk management was important as shiftworkers in these industries considered teamwork and welfare services to be essential for managing risks associated with night and shift work. Four areas found suitable for participatory improvement by managers and workers were work schedules, ergonomic work tasks, work environment and training. The checklist designed to facilitate participatory change processes covered all these areas. CONCLUSIONS: The checklist developed to describe feasible workplace actions was suitable for integration with comprehensive safety and health management systems and offered valuable opportunities for improving working time arrangements and job content together.OBJETIVOS: Foram revisados diversas medidas de apoio úteis para incentivar abordagens conjuntas para a melhoria na organização do trabalho por turnos e os processos de gestão de saúde e segurança. As medidas para redução de risco em n

  20. Human errors and system variability in safety investigations of ...

    African Journals Online (AJOL)

    Until OJ January 2010, the IMO Code for casualty investigation was annexed to an Assembly Resolution and therefore enjoyed only the status of soft law. However, whilst the legal status then was different, the philosophy of safety investigations remains the same i.e. an investigation should not apportion blame and/or ...

  1. Modelling of the processes synchronized dealing with ecological safety within economic system

    Directory of Open Access Journals (Sweden)

    Prokopenko O. V.


    Full Text Available The synchronization as a scientific category is investigated. A set of indicators concerning economic system constituents at the enterprise and regional level is formed. A methodological approach to assessment of the processes synchronized dealing with ecological safety within economic system is proposed. A methodological approach to forecasting of economic system development dynamics mutually with the tools for the economic safety provision at the highest level is improved.

  2. Performance of safety management systems in Spanish food service establishments in view of their context characteristics

    NARCIS (Netherlands)

    Luning, P.A.; Chinchilla, A.C.; Jacxsens, L.; Kirezieva, K.K.; Rovira, J.


    Food service establishments (FSE) operate under restricted technological and organisational circumstances, making them susceptible to food safety problems as reported frequently. Aim of this study was to get insight in Food Safety Management System (FSMS) performance in different types of FSE in

  3. An approach for functional safety improvement of an existing automotive system

    NARCIS (Netherlands)

    Khabbaz Saberi, A.; Luo, Y.; Pawel Cichosz, F.; Brand, M. van den; Jansen, S.T.H.


    Safety of automotive systems is becoming more involved, specially for the case of autonomous vehicles. The ISO 26262 standard offers a systematic approach for designing a safe road vehicle (or subsystems of a car) from design phase through its production. However, providing functional safety

  4. 78 FR 47015 - Software Requirement Specifications for Digital Computer Software Used in Safety Systems of... (United States)


    ... COMMISSION Software Requirement Specifications for Digital Computer Software Used in Safety Systems of... 1 of RG 1.172, ``Software Requirement Specifications for Digital Computer Software used in Safety... (IEEE) Standard (Std.) 830-1998, ``IEEE Recommended Practice for Software Requirements Specifications...

  5. 14 CFR 91.107 - Use of safety belts, shoulder harnesses, and child restraint systems. (United States)


    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Use of safety belts, shoulder harnesses, and child restraint systems. 91.107 Section 91.107 Aeronautics and Space FEDERAL AVIATION... OPERATING AND FLIGHT RULES Flight Rules General § 91.107 Use of safety belts, shoulder harnesses, and child...

  6. Systematic assessment of core assurance activities in a company specific food safety management system

    NARCIS (Netherlands)

    Luning, P.A.; Marcelis, W.J.; Rovira, J.; Spiegel, van der M.; Uyttendaele, M.; Jacxsens, L.


    The dynamic environment wherein agri-food companies operate and the high requirements on food safety force companies to critically judge and improve their food safety management system (FSMS) and its performance. The objective of this study was to develop a diagnostic instrument enabling a

  7. Integrated care: an Information Model for Patient Safety and Vigilance Reporting Systems. (United States)

    Rodrigues, Jean-Marie; Schulz, Stefan; Souvignet, Julien


    Quality management information systems for safety as a whole or for specific vigilances share the same information types but are not interoperable. An international initiative tries to develop an integrated information model for patient safety and vigilance reporting to support a global approach of heath care quality.

  8. Towards a decision support system for control of multiple food safety hazards in raw milk production

    NARCIS (Netherlands)

    Spiegel, van der M.; Sterrenburg, P.; Haasnoot, W.; Fels-Klerx, van der H.J.


    Decision support systems (DSS) for controlling multiple food safety hazards in raw milk production have not yet been developed, but the underlying components are fragmentarily available. This article presents the state-of-the-art of essential DSS elements for judging food safety compliance of raw

  9. Development, Dissemination, and Assessment of a Food Safety Systems Management Curriculum for Agribusiness Students in Armenia (United States)

    Pokharel, Siroj; Marcy, Joseph E.; Neilan, Angela M.; Cutter, Catherine N.


    This study addresses the development, dissemination, and assessment of a Food Safety System Management (FSSM) curriculum offered to college-aged, agribusiness students in Yerevan, Armenia. Prior to beginning the program, demographic data were collected and a paper-based pretest was administered to access the food safety knowledge, behavior, and…

  10. Improving Occupational and Industrial Safety Management System at Coal Mining Enterprises (United States)

    Smagina, Svetlana; Kadnikova, Oksana; Demidenko, Ksenia; Chistyakova, Galina; Rolgayzer, Anastasia


    The article highlights the problem of mine workers occupational safety. The foreign and domestic experience of the field is analyzed. Some areas, activities and methods that meet modern requirements for ensuring occupational safety and production development, which are aimed at improving the quality of occupational safety management system, are described. The possibilities of their use in industrial safety of Kuzbass coal mining enterprises are considered. The proposed methods were implemented by JSC "Shakhta Yuzhnaya", "Kiselevsky Razrez" Ltd., the coal mining enterprises of the Kemerovo region.

  11. Effective vaccine safety systems in all countries: a challenge for more equitable access to immunization. (United States)

    Amarasinghe, Ananda; Black, Steve; Bonhoeffer, Jan; Carvalho, Sandra M Deotti; Dodoo, Alexander; Eskola, Juhani; Larson, Heidi; Shin, Sunheang; Olsson, Sten; Balakrishnan, Madhava Ram; Bellah, Ahmed; Lambach, Philipp; Maure, Christine; Wood, David; Zuber, Patrick; Akanmori, Bartholomew; Bravo, Pamela; Pombo, María; Langar, Houda; Pfeifer, Dina; Guichard, Stéphane; Diorditsa, Sergey; Hossain, Md Shafiqul; Sato, Yoshikuni


    Serious vaccine-associated adverse events are rare. To further minimize their occurrence and to provide adequate care to those affected, careful monitoring of immunization programs and case management is required. Unfounded vaccine safety concerns have the potential of seriously derailing effective immunization activities. To address these issues, vaccine pharmacovigilance systems have been developed in many industrialized countries. As new vaccine products become available to prevent new diseases in various parts of the world, the demand for effective pharmacovigilance systems in low- and middle-income countries (LMIC) is increasing. To help establish such systems in all countries, WHO developed the Global Vaccine Safety Blueprint in 2011. This strategic plan is based on an in-depth analysis of the vaccine safety landscape that involved many stakeholders. This analysis reviewed existing systems and international vaccine safety activities and assessed the financial resources required to operate them. The Blueprint sets three main strategic goals to optimize the safety of vaccines through effective use of pharmacovigilance principles and methods: to ensure minimal vaccine safety capacity in all countries; to provide enhanced capacity for specific circumstances; and to establish a global support network to assist national authorities with capacity building and crisis management. In early 2012, the Global Vaccine Safety Initiative (GVSI) was launched to bring together and explore synergies among on-going vaccine safety activities. The Global Vaccine Action Plan has identified the Blueprint as its vaccine safety strategy. There is an enormous opportunity to raise awareness for vaccine safety in LMIC and to garner support from a large number of stakeholders for the GVSI between now and 2020. Synergies and resource mobilization opportunities presented by the Decade of Vaccines can enhance monitoring and response to vaccine safety issues, thereby leading to more equitable

  12. Combining System Safety and Reliability to Ensure NASA CoNNeCT's Success (United States)

    Havenhill, Maria; Fernandez, Rene; Zampino, Edward


    Hazard Analysis, Failure Modes and Effects Analysis (FMEA), the Limited-Life Items List (LLIL), and the Single Point Failure (SPF) List were applied by System Safety and Reliability engineers on NASA's Communications, Navigation, and Networking reConfigurable Testbed (CoNNeCT) Project. The integrated approach involving cross reviews of these reports by System Safety, Reliability, and Design engineers resulted in the mitigation of all identified hazards. The outcome was that the system met all the safety requirements it was required to meet.

  13. U.S. Food System Working Conditions as an Issue of Food Safety. (United States)

    Clayton, Megan L; Smith, Katherine C; Pollack, Keshia M; Neff, Roni A; Rutkow, Lainie


    Food workers' health and hygiene are common pathways to foodborne disease outbreaks. Improving food system jobs is important to food safety because working conditions impact workers' health, hygiene, and safe food handling. Stakeholders from key industries have advanced working conditions as an issue of public safety in the United States. Yet, for the food industry, stakeholder engagement with this topic is seemingly limited. To understand this lack of action, we interviewed key informants from organizations recognized for their agenda-setting role on food-worker issues. Findings suggest that participants recognize the work standards/food safety connection, yet perceived barriers limit adoption of a food safety frame, including more pressing priorities (e.g., occupational safety); poor fit with organizational strategies and mission; and questionable utility, including potential negative consequences. Using these findings, we consider how public health advocates may connect food working conditions to food and public safety and elevate it to the public policy agenda.

  14. Applying the Toyota Production System: using a patient safety alert system to reduce error. (United States)

    Furman, Cathie; Caplan, Robert


    In 2002, Virginia Mason Medical Center (VMMC) adapted the Toyota Production System, also known as lean manufacturing. To translate the techniques of zero defects and stopping the line into health care, the Patient Safety Alert (PSA) system requires any employee who encounters a situation that is likely to harm a patient to make an immediate report and to cease any activity that could cause further harm (stopping the line). IMPLEMENTING THE PSA SYSTEM--STOPPING THE LINE: If any VMMC employee's practice or conduct is deemed capable of causing harm to a patient, a PSA can cause that person to be stopped from working until the problem is resolved. A policy statement, senior executive commitment, dedicated resources, a 24-hour hotline, and communication were all key features of implementation. As of December 2006, 6,112 PSA reports were received: 20% from managers, 8% from physicians, 44% from nurses, and 23% from nonclinical support personnel, for example. The number of reports received per month increased from an average of 3 in 2002 to 285 in 2006. Most reports were processed within 24 hours and were resolved within 2 to 3 weeks. Implementing the PSA system has drastically increased the number of safety concerns that are resolved at VMMC, while drastically reducing the time it takes to resolve them. Transparent discussion and feedback have helped promote staff acceptance and participation.

  15. Patient Safety Communication Among Differently Educated Nurses: Converging and Diverging Meaning Systems. (United States)

    Anbari, Allison Brandt; Vogelsmeier, Amy; Dougherty, Debbie S


    Studies that suggest an increased number of bachelor's prepared nurses (BSNs) at the bedside improves patient safety do not stratify their samples into traditional bachelor's and associates (ADN) to BSN graduates. This qualitative study investigated potential differences in patient safety meaning among BSNs and ADN to BSN graduates. Guided by the theory of Language Convergence/Meaning Divergence, interview data from eight BSN and eight ADN to BSN graduates were analyzed. Findings indicate there are two meaning levels or systems, the local level and the systemic level. At the local level, the meaning of patient safety is focused at the patient's bedside and regulated by the nurse. The systemic level included the notion that health system factors such as policies and staffing are paramount to keeping patients safe. More frequently, ADN to BSN graduates' meaning of patient safety was at the local level, while BSNs' meaning centered at the systemic level.

  16. Preliminary design of safety and interlock system for indian test facility of diagnostic neutral beam

    Energy Technology Data Exchange (ETDEWEB)

    Tyagi, Himanshu, E-mail: [ITER-India, Institute For Plasma Research, Bhat, Gandhinagar, Gujarat (India); Soni, Jignesh [Institute For Plasma Research, Bhat, Gandhinagar, Gujarat (India); Yadav, Ratnakar; Bandyopadhyay, Mainak; Rotti, Chandramouli [ITER-India, Institute For Plasma Research, Bhat, Gandhinagar, Gujarat (India); Gahlaut, Agrajit [Institute For Plasma Research, Bhat, Gandhinagar, Gujarat (India); Joshi, Jaydeep; Parmar, Deepak [ITER-India, Institute For Plasma Research, Bhat, Gandhinagar, Gujarat (India); Bansal, Gourab; Pandya, Kaushal; Chakraborty, Arun [Institute For Plasma Research, Bhat, Gandhinagar, Gujarat (India)


    Highlights: • Indian Test Facility being built to characterize DNB for ITER delivery. • Interlock system required to safeguard the investment incurred in building the facility and protecting ITER deliverable components. • Interlock levels upto 3IL-3 identified. • Safety instrumented system for occupational safety being designed. Safety I&C functions of SIL-2 identified. • The systems are based on ITER PIS and PSS design guidelines. - Abstract: Indian Test Facility (INTF) is being built in Institute For Plasma Research to characterize Diagnostic Neutral Beam in co-operation with ITER Organization. INTF is a complex system which consists of several plant systems like beam source, gas feed, vacuum, cryogenics, high voltage power supplies, high power RF generators, mechanical systems and diagnostics systems. Out of these, several INTF components are ITER deliverable, that is, beam source, beam line components and power supplies. To ensure successful operation of INTF involving integrated operation of all the constituent plant systems a matured Data Acquisition and Control System (DACS) is required. The INTF DACS is based on CODAC platform following on PCDH (Plant Control Design Handbook) guidelines. The experimental phases involve application of HV power supplies (100 KV) and High RF power (∼800 KW) which will produce energetic beam of maximum power 6MW within the facility for longer durations. Hence the entire facility will be exposed tohigh heat fluxes and RF radiations. To ensure investment protection and to provide occupational safety for working personnel a matured Safety and Interlock system is required for INTF. The Safety and Interlock systems are high-reliability I&C systems devoted completely to the specific functions. These systems will be separate from the conventional DACS of INTF which will handle the conventional control and acquisition functions. Both, the Safety and Interlock systems are based on IEC 61511 and IEC 61508 standards as

  17. Leading Edge. Volume 7, Number 3. Systems Safety Engineering (United States)


    Technical Laboratory (LNTL) for Laser Safety Within the Department of the Navy (DON) Sheldon Zimmerman , Robert Aldrich, and Thomas Fraser 3 Volume 7...Greg Sellers Kevin Stottlar Jason Taubel Shawn T. Thumm Eric Weissman James H. Yee Michael Zemore Sheldon Zimmerman NSWC Dam Neck Brian J. Schwark...such events as Rachel Carson’s 1962 penning of the con- troversial Silent Spring, the passing of NEPA in 1969, and President Nixon’s establishment

  18. Aspects of safety and reliability for fusion magnet systems first annual report

    Energy Technology Data Exchange (ETDEWEB)

    Powell, J. (ed.)


    General systems aspects of fusion magnet safety are examined first, followed by specific detailed analyses covering structural, thermal, electrical, and other aspects of fusion magnet safety. The design examples chosen for analysis are illustrative and are not intended to be definitive, since fusion magnet designs are rapidly evolving. Included is a comprehensive collection of design and operating data relating to the safety of existing superconducting magnet systems. The remainder of the overview lists the main conclusions developed from the work to date. These should be regarded as initial steps. Since this study has concentrated on examining potential safety concerns, it may tend to overemphasize the problems of fusion magnets. In fact, many aspects of fusion magnets are well developed and are consistent with good safety practice. A short summary of the findings of this study is given.

  19. The Research on Safety Management Information System of Railway Passenger Based on Risk Management Theory (United States)

    Zhu, Wenmin; Jia, Yuanhua


    Based on the risk management theory and the PDCA cycle model, requirements of the railway passenger transport safety production is analyzed, and the establishment of the security risk assessment team is proposed to manage risk by FTA with Delphi from both qualitative and quantitative aspects. The safety production committee is also established to accomplish performance appraisal, which is for further ensuring the correctness of risk management results, optimizing the safety management business processes and improving risk management capabilities. The basic framework and risk information database of risk management information system of railway passenger transport safety are designed by Ajax, Web Services and SQL technologies. The system realizes functions about risk management, performance appraisal and data management, and provides an efficient and convenient information management platform for railway passenger safety manager.

  20. 78 FR 47805 - Test Documentation for Digital Computer Software Used in Safety Systems of Nuclear Power Plants (United States)


    ... COMMISSION Test Documentation for Digital Computer Software Used in Safety Systems of Nuclear Power Plants..., ``Test Documentation for Digital Computer Software Used in Safety Systems of Nuclear Power Plants.'' This... quality in the software used in safety systems of nuclear power plants. ADDRESSES: Please refer to Docket...

  1. L-Band Digital Aeronautical Communications System Engineering - Initial Safety and Security Risk Assessment and Mitigation (United States)

    Zelkin, Natalie; Henriksen, Stephen


    This document is being provided as part of ITT's NASA Glenn Research Center Aerospace Communication Systems Technical Support (ACSTS) contract NNC05CA85C, Task 7: "New ATM Requirements--Future Communications, C-Band and L-Band Communications Standard Development." ITT has completed a safety hazard analysis providing a preliminary safety assessment for the proposed L-band (960 to 1164 MHz) terrestrial en route communications system. The assessment was performed following the guidelines outlined in the Federal Aviation Administration Safety Risk Management Guidance for System Acquisitions document. The safety analysis did not identify any hazards with an unacceptable risk, though a number of hazards with a medium risk were documented. This effort represents a preliminary safety hazard analysis and notes the triggers for risk reassessment. A detailed safety hazards analysis is recommended as a follow-on activity to assess particular components of the L-band communication system after the technology is chosen and system rollout timing is determined. The security risk analysis resulted in identifying main security threats to the proposed system as well as noting additional threats recommended for a future security analysis conducted at a later stage in the system development process. The document discusses various security controls, including those suggested in the COCR Version 2.0.

  2. A survey on reliability and safety analysis techniques of robot systems in nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Eom, H.S.; Kim, J.H.; Lee, J.C.; Choi, Y.R.; Moon, S.S


    The reliability and safety analysis techniques was surveyed for the purpose of overall quality improvement of reactor inspection system which is under development in our current project. The contents of this report are : 1. Reliability and safety analysis techniques suvey - Reviewed reliability and safety analysis techniques are generally accepted techniques in many industries including nuclear industry. And we selected a few techniques which are suitable for our robot system. They are falut tree analysis, failure mode and effect analysis, reliability block diagram, markov model, combinational method, and simulation method. 2. Survey on the characteristics of robot systems which are distinguished from other systems and which are important to the analysis. 3. Survey on the nuclear environmental factors which affect the reliability and safety analysis of robot system 4. Collection of the case studies of robot reliability and safety analysis which are performed in foreign countries. The analysis results of this survey will be applied to the improvement of reliability and safety of our robot system and also will be used for the formal qualification and certification of our reactor inspection system.

  3. What are occupational safety and health management systems and why do companies implement them?

    NARCIS (Netherlands)

    Zwetsloot, G.I.J.M.


    In company practice and in governmental legislation, it is increasingly acknowledged that occupational safety and health (OSH) management should be performed systematically and continually. Implementing an OSH Management System (OSH MS) is the major strategy to achieve this.

  4. 78 FR 50079 - Information Collection Activities: Safety and Environmental Management Systems (SEMS); Proposed... (United States)


    ...: 134E1700D2 EEEE500000 ET1SF0000.DAQ000] Information Collection Activities: Safety and Environmental Management Systems (SEMS); Proposed Collection; Comment Request Correction In notice document 2013-19416...

  5. Safety and fitness electronic records (SAFER) system : logical architecture document : working draft (United States)


    This Logical Architecture Document includes the products developed during the functional analysis of the Safety and Fitness Electronic Records (SAFER) System. This document, along with the companion Operational Concept and Physical Architecture Docum...

  6. Tools to support the self assessment of the performance of Food Safety Management Systems

    NARCIS (Netherlands)

    Luning, P.A.; Jacxsens, L.; Jasson, V.; Marcelis, W.J.; Kussaga, J.; Spiegel, van der M.; Koesta, M.; Oses Gomez, S.; Rovira, J.; Devlieghere, F.; Uyttendaele, M.


    Changes in food supply chains, health and demographic situations, lifestyle and social situations, environmental conditions, and increased legislative requirements have led to significant efforts in the development of quality and safety management systems in agribusiness and food industry worldwide

  7. Renovated Korean nuclear safety and security system: A review and suggestions to successful settlement

    Energy Technology Data Exchange (ETDEWEB)

    Chung, W. S.; Yun, S. W.; Lee, D. S. [Korea Atomic Energy Research Inst., Dukjin-dong 150, Yusung-gu, Daejon, R.O., 305-353 (Korea, Republic of); Go, D. Y. [Kyung Hee Univ., Kyung Hee daero 26, Dongdaemoon-gu, Seoul, R.O., 130-701 (Korea, Republic of)


    Questions of whether past nuclear regulatory body of Korea is not a proper system to monitor and check the country's nuclear energy policy and utilization have been raised. Moreover, a feeling of insecurity regarding nuclear safety after the nuclear accident in Japan has spread across the public. This has stimulated a renovation of the nuclear safety regime in Korea. The Nuclear Safety and Security Commission (NSSC) was launched on October 26, 2011 as a regulatory body directly under the President in charge of strengthening independence and nuclear safety. This was a meaningful event as the NSSC it is a much more independent regulatory system for Korea. However, the NSSC itself does not guarantee an enhanced public acceptance of the nuclear policy and stable use nuclear energy. This study introduces the new NSSC system and its details in terms of organization structure, appropriateness of specialty, budget stability, and management system. (authors)

  8. Safety management of a complex R&D ground operating system (United States)

    Connors, J.; Mauer, R. A.


    Report discusses safety program implementation for large R&D operating system. Analytical techniques are defined and suggested as tools for identifying potential hazards and determining means to effectively control or eliminate hazards.

  9. Data Analysis of Occupational Health and Safety Management and Total Quality Management Systems

    Directory of Open Access Journals (Sweden)

    Ahmet Yakut


    Full Text Available In our study, Total Quality Management, Occupational Health and Safety on the effects of the construction industry, building sites of Istanbul evaluated with the results of the survey of 25 firms. For Occupational Health and Safety program, walked healthy, active employees in her role increased and will increase the importance of education. Due to non-implementation of the OHS system in our country enough, work-related accidents and deaths and injuries resulting from these accidents is very high. Firms as a result of the analysis, an effective health and safety management system needs to be able to fulfill their responsibilities. This system is designated as OHSAS 18001 Occupational Health and Safety Management System and the construction industry can be regarded as the imperatives.

  10. Evolution of System Safety at NASA as Related to Defense-in-Depth (United States)

    Dezfuli, Homayoon


    Presentation given at the Defense-in-Depth Inter-Agency Workshop on August 26, 2015 in Rockville, MD by Homayoon Dezfuli. The presentation addresses the evolution of system safety at NASA as related to Defense-in-Depth.

  11. Analytical Methods for Verification and Validation of Adaptive Systems in Safety-Critical Aerospace Applications Project (United States)

    National Aeronautics and Space Administration — A major challenge of the use of adaptive systems in safety-critical applications is the software life-cycle: requirement engineering through verification and...

  12. Influence of UV Treatment on the Food Safety Status of a Model Aquaponic System

    National Research Council Canada - National Science Library

    Elumalai, Sai; Shaw, Angela; Pattillo, D; Currey, Christopher; Rosentrater, Kurt; Xie, Kun


    ... (15 W, luminous flux of 900 lm) as a food safety intervention in reducing the microbial loads of the water system in a model aquaponic unit growing lettuce, basil, and barramundi (Australian Sea Bass...

  13. Optimization of Safety Instrumented System Design and Maintenance Frequency for Oil and Gas Industry Processes

    National Research Council Canada - National Science Library

    Yury Redutskiy


    ... for safety system design is introduced in a generalized form. The model aims to reflect the divergent perspectives of the main parties involved in oil and gas projects, and, therefore, it is formulated as a multi-objective problem...

  14. Pediatric post-marketing safety systems in North America: assessment of the current status. (United States)

    McMahon, Ann W; Wharton, Gerold T; Bonnel, Renan; DeCelle, Mary; Swank, Kimberley; Testoni, Daniela; Cope, Judith U; Smith, Phillip Brian; Wu, Eileen; Murphy, Mary Dianne


    It is critical to have pediatric post-marketing safety systems that contain enough clinical and epidemiological detail to draw regulatory, public health, and clinical conclusions. The pediatric safety surveillance workshop (PSSW), coordinated by the Food and Drug Administration (FDA), identified these pediatric systems as of 2010. This manuscript aims to update the information from the PSSW and look critically at the systems currently in use. We reviewed North American pediatric post-marketing safety systems such as databases, networks, and research consortiums found in peer-reviewed journals and other online sources. We detail clinical examples from three systems that FDA used to assess pediatric medical product safety. Of the 59 systems reviewed for pediatric content, only nine were pediatric-focused and met the inclusion criteria. Brief descriptions are provided for these nine. The strengths and weaknesses of three systems (two of the nine pediatric-focused and one including both children and adults) are illustrated with clinical examples. Systems reviewed in this manuscript have strengths such as clinical detail, a large enough sample size to capture rare adverse events, and/or a patient denominator internal to the database. Few systems include all of these attributes. Pediatric drug safety would be better informed by utilizing multiple systems to take advantage of their individual characteristics. Copyright © 2015 John Wiley & Sons, Ltd.

  15. A study in improvement of administrative system in the nuclear safety regulation

    Energy Technology Data Exchange (ETDEWEB)

    Yook, Dong Il; Kuk, Doe Hyeong; Lee, Seong Min; Kim, Jong Sam; Hwang, Sun Ho [Chungnam National Univ., Taejon (Korea, Republic of)


    One of the most important tasks to improve nuclear safety regulation system is to separate nuclear regulatory institutes from public agencies which promote the development nuclear power. Moreover, nuclear safety regulation should be not only specialized but optimized to be adapted for new environments such as high-tech information age. Especially, it is necessary to reform the current nuclear safety regulation systems both to be effective under the local self-administration which began to operate in recent years and to be supported by local residents.

  16. Rapid Prototyping of the Central Safety System for Nuclear Risk in ITER

    Energy Technology Data Exchange (ETDEWEB)

    Scibile, L. [ITER Organization, 13 - St. Paul lez Durance (France); Ambrosino, G.; De Tommasi, G.; Pironti, A. [Euratom-ENEA-CREATE, Universita di Napoli Federico II, Napoli (Italy)


    Full text of publication follows: In the current ITER Baseline design, the Central Safety System for Nuclear Risk (CSS-N) is the safety control system in charge to assure nuclear safety for the plant, personnel and environment. In particular it is envisaged that the CSS shall interface to the plant safety systems for nuclear risk and shall coordinate the individual protection provided by the intervention of these systems by the activation, where required, of additional protections. The design of such a system, together with its implementation, strongly depends on the requirements, particularly in terms of reliability. The CSS-N is a safety critical system, thus its validation and commissioning play a very important role, since the required level of reliability must be demonstrated. In such a scenario, where a new and non-conventional system has to be deployed, it is strongly recommended to use modeling and simulation tools since the early design phase. Indeed, the modeling tools will help in the definition of the system requirements, and they will be used to test and validate the control logic. Furthermore these tools can be used to rapid design the safety system and to carry out hardware-in-the-loop (HIL) simulations, which permit to assess the performance of the control hardware against a plant simulator. Both a control system prototype and a safety system oriented plant simulator have been developed to assess first the requirements and then the performance of the CSS-N. In particular the presented SW/HW framework permits to design and verify the CSS protection logics and to test and validate these logics by means of HIL simulations. This work introduces both the prototype and plant simulator architectures, together with the methodology adopted to design and implement these validation tools. (authors)

  17. Importance of Decision Support Systems About Food Safety in Raw Milk Production

    Directory of Open Access Journals (Sweden)

    Ecem Akan


    Full Text Available In raw milk production decision support systems for control of food safety hazards has not been developed but main points of this system are available. The decision support systems’ elements include data identification at critical points in the milk supply chain, an information management system and data exchange. Decision supports systems has been developed on the basis of these elements. In dairy sector decision support systems are significant for controlling of food safety hazards and preferred by producers. When these systems are implemented in the milk supply chain, it can be prevented unnecessary sampling and analysis. In this article it will be underlined effects of decision support system elements on food safety of raw milk.

  18. Integration of occupational health and safety, environmental and quality management system standards. (United States)

    Stromsvag, A; Winder, C


    Occupational health and safety, environmental, and quality (SEQ) issues are commonly managed by three separate departments within organizations. Because of a number of commonalities in the three management systems, there could be a degree of overlap that might lead to inefficiencies. By integrating these three management systems into one SEQ system, the duplication of effort could be minimized and the health and safety, environmental, and quality issues could be managed by one common proactive approach. The draft Australian standard for an occupational health and safety (OHS) management system and the internationally accepted standards for environmental (ISO 14001) and quality (ISO 9001) management systems were analyzed to identify all requirements of the three management systems and integrate this into one SEQ management system standard.

  19. Knowledge management and safety compliance in a high-risk distributed organizational system. (United States)

    Gressgård, Leif Jarle


    In a safety perspective, efficient knowledge management is important for learning purposes and thus to prevent errors from occurring repeatedly. The relationship between knowledge exchange among employees and safety behavior may be of particular importance in distributed organizational systems where similar high-risk activities take place at several locations. This study develops and tests hypotheses concerning the relationship between knowledge exchange systems usage, knowledge exchange in the organizational system, and safety compliance. The operational context of the study is petroleum drilling and well operations involving distributed high-risk activities. The hypotheses are tested by use of survey data collected from a large petroleum operator company and eight of its main contractors. The results show that safety compliance is influenced by use of knowledge exchange systems and degree of knowledge exchange in the organizational system, both within and between units. System usage is the most important predictor, and safety compliance seems to be more strongly related to knowledge exchange within units than knowledge exchange between units. Overall, the study shows that knowledge management is central for safety behavior.

  20. Implementation and evaluation of a prototype consumer reporting system for patient safety events. (United States)

    Weingart, Saul N; Weissman, Joel S; Zimmer, Karen P; Giannini, Robert C; Quigley, Denise D; Hunter, Lauren E; Ridgely, M Susan; Schneider, Eric C


    No methodologically robust system exists for capturing consumer-generated patient safety reports. To address this challenge, we developed and pilot-tested a prototype consumer reporting system for patient safety, the Health Care Safety Hotline. Mixed methods evaluation. The Hotline was implemented in two US healthcare systems from 1 February 2014 through 30 June 2015. Patients, family members and caregivers associated with two US healthcare systems. A consumer-oriented incident reporting system for telephone or web-based administration was developed to elicit medical mistakes and care-related injuries. Key informant interviews, measurement of website traffic and analysis of completed reports. Key informants indicated that Hotline participation was motivated by senior leaders' support and alignment with existing quality and safety initiatives. During the measurement period from 1 October 2014 through 30 June 2015, the home page had 1530 visitors with a unique IP address. During its 17 months of operation, the Hotline received 37 completed reports including 20 mistakes without harm and 15 mistakes with injury. The largest category of mistake concerned problems with diagnosis or advice from a health practitioner. Hotline reports prompted quality reviews, an education intervention, and patient follow-ups. While generating fewer reports than its capacity to manage, the Health Care Safety Hotline demonstrated the feasibility of consumer-oriented patient safety reporting. Further research is needed to understand how to increase consumers' use of these systems.

  1. Problematics of approaches to research of the use safety of ergatic control systems on railway transport

    Directory of Open Access Journals (Sweden)

    O. Y. Kamenyev


    Full Text Available Purpose. Determination of the protective state influence of ergatic control system on a railway transport on their use safety. Making recommendations concerning its accounting for regulations and testing during the development and implementation. Methodology. Research is executed on the base of reliability theory with the use of exponential law of refusals distribution. Findings. It is shown that confirmation of ergatic technical control facilities accordance and trains traffic arrangement to certain functional level of security is not sufficient for guaranteeing of their use safety. It is established that the protective refusal of ergatic control system does not exclude, but only postpones the dangerous condition of the system. Originality. Further development of approach and requirements to research of use safety of ergatic control system on a railway transport are received. Unlike previous they take into account the indexes of not only functional unconcern, but also faultlessness at setting of norms and proof of these systems safety. Practical value. Accounting of protective refusals of technical facilities at tests on their safety application, and also setting of norms of characteristics reliability of control systems by responsible technological processes on a railway transport in accordance with offered approach allows to increase level of their use safety in the exploitation process.

  2. Analysis of Aviation Safety Reporting System Incident Data Associated with the Technical Challenges of the Atmospheric Environment Safety Technology Project (United States)

    Withrow, Colleen A.; Reveley, Mary S.


    This study analyzed aircraft incidents in the NASA Aviation Safety Reporting System (ASRS) that apply to two of the three technical challenges (TCs) in NASA's Aviation Safety Program's Atmospheric Environment Safety Technology Project. The aircraft incidents are related to airframe icing and atmospheric hazards TCs. The study reviewed incidents that listed their primary problem as weather or environment-nonweather between 1994 and 2011 for aircraft defined by Federal Aviation Regulations (FAR) Parts 121, 135, and 91. The study investigated the phases of flight, a variety of anomalies, flight conditions, and incidents by FAR part, along with other categories. The first part of the analysis focused on airframe-icing-related incidents and found 275 incidents out of 3526 weather-related incidents over the 18-yr period. The second portion of the study focused on atmospheric hazards and found 4647 incidents over the same time period. Atmospheric hazards-related incidents included a range of conditions from clear air turbulence and wake vortex, to controlled flight toward terrain, ground encounters, and incursions.

  3. Ecological Design of Cooperative Human-Machine Interfaces for Safety of Intelligent Transport Systems

    Directory of Open Access Journals (Sweden)

    Orekhov Aleksandr


    Full Text Available The paper describes research results in the domain of cooperative intelligent transport systems. The requirements for human-machine interface considering safety issue of for intelligent transport systems (ITSare analyzed. Profiling of the requirements to cooperative human-machine interface (CHMI for such systems including requirements to usability and safety is based on a set of standards for ITSs. An approach and design technique of cooperative human-machine interface for ITSs are suggested. The architecture of cloud-based CHMI for intelligent transport systems has been developed. The prototype of software system CHMI4ITSis described.

  4. Impact of Passive Safety on FHR Instrumentation Systems Design and Classification

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, David Eugene [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)


    Fluoride salt-cooled high-temperature reactors (FHRs) will rely more extensively on passive safety than earlier reactor classes. 10CFR50 Appendix A, General Design Criteria for Nuclear Power Plants, establishes minimum design requirements to provide reasonable assurance of adequate safety. 10CFR50.69, Risk-Informed Categorization and Treatment of Structures, Systems and Components for Nuclear Power Reactors, provides guidance on how the safety significance of systems, structures, and components (SSCs) should be reflected in their regulatory treatment. The Nuclear Energy Institute (NEI) has provided 10 CFR 50.69 SSC Categorization Guideline (NEI-00-04) that factors in probabilistic risk assessment (PRA) model insights, as well as deterministic insights, through an integrated decision-making panel. Employing the PRA to inform deterministic requirements enables an appropriately balanced, technically sound categorization to be established. No FHR currently has an adequate PRA or set of design basis accidents to enable establishing the safety classification of its SSCs. While all SSCs used to comply with the general design criteria (GDCs) will be safety related, the intent is to limit the instrumentation risk significance through effective design and reliance on inherent passive safety characteristics. For example, FHRs have no safety-significant temperature threshold phenomena, thus enabling the primary and reserve reactivity control systems required by GDC 26 to be passively, thermally triggered at temperatures well below those for which core or primary coolant boundary damage would occur. Moreover, the passive thermal triggering of the primary and reserve shutdown systems may relegate the control rod drive motors to the control system, substantially decreasing the amount of safety-significant wiring needed. Similarly, FHR decay heat removal systems are intended to be running continuously to minimize the amount of safety-significant instrumentation needed to initiate

  5. Common-cause Failures as Major Issue in Safety of Control Systems

    Directory of Open Access Journals (Sweden)

    Juraj Ilavsky


    Full Text Available In order to gain an improvement of safety or availability measures of the safety-relevant control system through employment of redundancy a redundant system has to comply with the requirement on independence of redundant parts. If the requirements on the independence of redundant parts are unfulfilled, then a common-cause failure can directly cause a hazardous state on a system level through its effects on multiple redundant parts. Identification of sources and quantification of the common-cause failure parameters has been proved to be a formidable task. The latter problem, including other major safety-affecting factors lays in the focus of this paper. Our proposed technical safety analysis concept is extended, so now it partially covers elusive problems related to the common-cause failures.

  6. Fluor Hanford Integrated Safety Management System Phase II Verification Vol 1 & Vol 2

    Energy Technology Data Exchange (ETDEWEB)



    The U.S. Department of Energy (DOE) is committed to conducting work efficiently and in a manner that ensures protection of the workers, public, and environment. DOE policy mandates that safety management systems be used to systematically integrate safety into management and work practices at all levels while accomplishing mission goals in an effective and efficient manner. The purpose of the Fluor Hanford (FH) Integrated Safety Management System (ISMS) verification was to determine whether FH's ISM system and processes are sufficiently implemented to accomplish the goal of ''Do work safely.'' The purpose of the DOE, Richland Operations Office (RL) verification was to determine whether RL has established processes that adequately describe RL's role in safety management and if those processes are sufficiently implemented.

  7. Optimization of Safety Instrumented System Design and Maintenance Frequency for Oil and Gas Industry Processes

    Directory of Open Access Journals (Sweden)

    Redutskiy Yury


    Full Text Available Oil and gas industry processes are associated with significant expenditures and risks. Adequacy of the decisions on safety measures made during early stages of planning the facilities and processes contributes to avoiding technological incidents and corresponding losses. Formulating straightforward requirements for safety instrumented systems that are followed further during the detailed engineering design and operations is proposed, and a mathematical model for safety system design is introduced in a generalized form. The model aims to reflect the divergent perspectives of the main parties involved in oil and gas projects, and, therefore, it is formulated as a multi-objective problem. Application of black box optimization is suggested for solving real-life problem instances. A Markov model is applied to account for device failures, technological incidents, continuous restorations and periodic maintenance for a given process and safety system configuration. This research is relevant to engineering departments and contractors, who specialize in planning and designing the technological solution.

  8. Fluor Hanford Integrated Safety Management System Phase II Verification Vol 1 and Vol 2

    CERN Document Server

    Parsons, J E


    The U.S. Department of Energy (DOE) is committed to conducting work efficiently and in a manner that ensures protection of the workers, public, and environment. DOE policy mandates that safety management systems be used to systematically integrate safety into management and work practices at all levels while accomplishing mission goals in an effective and efficient manner. The purpose of the Fluor Hanford (FH) Integrated Safety Management System (ISMS) verification was to determine whether FH's ISM system and processes are sufficiently implemented to accomplish the goal of ''Do work safely.'' The purpose of the DOE, Richland Operations Office (RL) verification was to determine whether RL has established processes that adequately describe RL's role in safety management and if those processes are sufficiently implemented.

  9. JACoW Safety instrumented systems and the AWAKE plasma control as a use case

    CERN Document Server

    Blanco Viñuela, Enrique; Fernández Adiego, Borja; Speroni, Roberto


    Safety is likely the most critical concern in many process industries, yet there is a general uncertainty on the proper engineering to reduce the risks and ensure the safety of persons or material at the same time as providing the process control system. Some of the reasons for this misperception are unclear requirements, lack of functional safety engineering knowledge or incorrect protection functionalities attributed to the BPCS (Basic Process Control System). Occasionally the control engineers are not aware of the hazards inherent to an industrial process and this causes an incorrect design of the overall controls. This paper illustrates the engineering of the SIS (Safety Instrumented System) and the BPCS of the plasma vapour controls of the AWAKE R&D; project, the first proton-driven plasma wakefield acceleration experiment in the world. The controls design and implementation refers to the IEC61511/ISA84 standard, including technological choices, design, operation and maintenance. Finally, the publica...

  10. [Implementation of a safety and health planning system in a teaching hospital]. (United States)

    Mariani, F; Bravi, C; Dolcetti, L; Moretto, A; Palermo, A; Ronchin, M; Tonelli, F; Carrer, P


    University Hospital "L. Sacco" had started in 2006 a two-year project in order to set up a "Health and Safety Management System (HSMS)" referring to the technical guideline OHSAS 18001:1999 and the UNI and INAIL "Guidelines for a health and safety management system at workplace". So far, the following operations had been implemented: Setting up of a specific Commission within the Risk Management Committee; Identification and appointment of Departmental Representatives of HSMS; Carrying out of a training course addressed to Workers Representatives for Safety and Departmental Representatives of HSMS; Development of an Integrated Informative System for Prevention and Safety; Auditors qualification; Inspection of the Occupational Health Unit and the Prevention and Safety Service: reporting of critical situations and monitoring solutions adopted. Short term objectives are: Self-evaluation through check-lists of each department; Sharing of the Improvement Plan among the departments of the hospital; Planning of Health and Safety training activities in the framework of the Hospital Training Plan; Safety audit.

  11. On the Safety of Machine Learning: Cyber-Physical Systems, Decision Sciences, and Data Products. (United States)

    Varshney, Kush R; Alemzadeh, Homa


    Machine learning algorithms increasingly influence our decisions and interact with us in all parts of our daily lives. Therefore, just as we consider the safety of power plants, highways, and a variety of other engineered socio-technical systems, we must also take into account the safety of systems involving machine learning. Heretofore, the definition of safety has not been formalized in a machine learning context. In this article, we do so by defining machine learning safety in terms of risk, epistemic uncertainty, and the harm incurred by unwanted outcomes. We then use this definition to examine safety in all sorts of applications in cyber-physical systems, decision sciences, and data products. We find that the foundational principle of modern statistical machine learning, empirical risk minimization, is not always a sufficient objective. We discuss how four different categories of strategies for achieving safety in engineering, including inherently safe design, safety reserves, safe fail, and procedural safeguards can be mapped to a machine learning context. We then discuss example techniques that can be adopted in each category, such as considering interpretability and causality of predictive models, objective functions beyond expected prediction accuracy, human involvement for labeling difficult or rare examples, and user experience design of software and open data.

  12. [New international initiatives to create systems of effective risk prediction and food safety]. (United States)

    Efimochkinal, N R; Bagryantseva, E C; Dupouy, E C; Khotimchenko, S A; Permyakov, E V; Sheveleva, S A; Arnautov, O V


    Ensuring food safety is one of the most important problems that is directly related to health protection of the population. The problem is particularly relevant on aglobalscale because ofincreasingnumberoffood-borne diseases andimportance of the health consequence early detection. In accordance with the position of the Codex Alimentarius Commission, food safety concept also includes quality. In this case, creation of the national, supranational and international early warning systems related to the food safety, designed with the purpose to prevent or minimize risks on different stages of the food value chain in various countries, regions and climate zones specific to national nutrition and lifestyle in different groups of population, gains particular importance. The article describes the principles and working examples of international, supranational and national food safety early warning systems. Great importance is given to the hazards of microbial origin - emergent pathogens. Example of the rapid reaction to the appearance of cases, related to the melanin presence in infant formula, are presented. Analysis of the current food safety and quality control system in Russian Federation shows that main improvements are mostly related to the development of the efficient monitoring, diagnostics and rapid alert procedures forfood safety on interregional and international levels that will allow to estimate real contamination of food with the most dangerous pathogens, chemical and biological contaminants, and the development of the electronic database and scientifically proved algorithms for food safety and quality management for targeted prevention activities against existing and emerging microbiological and other etiology risks, and public health protection.

  13. Discussion on software aging management of nuclear power plant safety digital control system. (United States)

    Liang, Huihui; Gu, Pengfei; Tang, Jianzhong; Chen, Weihua; Gao, Feng


    Managing the aging of digital control systems ensures that nuclear power plant systems are in adequate safety margins during their life cycles. Software is a core component in the execution of control logic and differs between digital and analog control systems. The hardware aging management for the digital control system is similar to that for the analog system, which has matured over decades of study. However, software aging management is still in the exploratory stage. Software aging evaluation is critical given the higher reliability and safety requirements of nuclear power plants. To ensure effective inputs for reliability assessment, this paper provides the required software aging information during the life cycle. Moreover, the software aging management scheme for safety digital control system is proposed on the basis of collected aging information.

  14. Diversity for security: case assessment for FPGA-based safety-critical systems

    Directory of Open Access Journals (Sweden)

    Kharchenko Vyacheslav


    Full Text Available Industrial safety critical instrumentation and control systems (I&Cs are facing more with information (in general and cyber, in particular security threats and attacks. The application of programmable logic, first of all, field programmable gate arrays (FPGA in critical systems causes specific safety deficits. Security assessment techniques for such systems are based on heuristic knowledges and the expert judgment. Main challenge is how to take into account features of FPGA technology for safety critical I&Cs including systems in which are applied diversity approach to minimize risks of common cause failure. Such systems are called multi-version (MV systems. The goal of the paper is in description of the technique and tool for case-based security assessment of MV FPGA-based I&Cs.

  15. The Road Safety Information System RIS : a tool for decision makers. Lecture for the Russian-Swedish seminar on traffic safety, Moscow, June 18, 1996.


    Wesemann, P. & Brouwer, M.


    The subject of this lecture is the use of knowledge in the preparation and evaluation of road safety policy. The following subjects will be dealt with: the organisation of Dutch road safety policy; the type of knowledge that can enhance the effectiveness of this policy; the set-up of the developed Road safety Information System, to which will be referred by its acronym `RIS'; the advantages of the RIS for the users; further application potential of the RIS.

  16. [A simplified occupational health and safety management system designed for small enterprises. Initial validation results]. (United States)

    Bacchi, Romana; Veneri, L; Ghini, P; Caso, Maria Alessandra; Baldassarri, Giovanna; Renzetti, F; Santarelli, R


    Occupational Health and Safety Management Systems (OHSMS) are known to be effective in improving safety at work. Unfortunately they are often too resource-heavy for small businesses. The aim of this project was to develop and test a simplified model of OHSMS suitable for small enterprises. The model consists of 7 procedures and various operating forms and check lists, that guide the enterprise in managing safety at work. The model was tested in 15 volunteer enterprises. In most of the enterprises two audits showed increased awareness and participation of workers; better definition and formalisation of respon sibilities in 8 firms; election of Union Safety Representatives in over one quarter of the enterprises; improvement of safety equipment. The study also helped identify areas where the model could be improved by simplification of unnecessarily complex and redundant procedures.

  17. Key Element Performance In Occupational Safety And Health Management System In Organization (A Literature

    Directory of Open Access Journals (Sweden)

    Agus Salim Nuzaihan Aras


    Full Text Available Setting an effective safety and health management system is crucial in order to reduce problem relating to accident and ill in management organizational. It is involve with multiple level of management and stakeholders who empower the organization to the management in handling the safety and health cases and issues in organizational. It is necessary to prepare a well knowledge about safety and health management systems and preparing the framework for setting a certain scale in measuring its performance in this area. The successful or failure of management does showing the capability of the organization in delivering the responsible to management levels [1]. The problem in safe work issues and practices cause by the management commitment and involvement that create improper safety program and procedures, and this crisis keep continuing till present [2]. This paper describes about key element of safety and health management system and measuring the performance in order to get an effective management system in organization that describes the process in achieving effectiveness in management. The literature review will be conducted through the data collection from research findings and defined the strong character of key element in which focusing on measuring performance. A guide on key element performance in occupational safety and health management system is specifically drawn to prepare for a future research.

  18. Reliability modelling of redundant safety systems without automatic diagnostics incorporating common cause failures and process demand. (United States)

    Alizadeh, Siamak; Sriramula, Srinivas


    Redundant safety systems are commonly used in the process industry to respond to hazardous events. In redundant systems composed of identical units, Common Cause Failures (CCFs) can significantly influence system performance with regards to reliability and safety. However, their impact has been overlooked due to the inherent complexity of modelling common cause induced failures. This article develops a reliability model for a redundant safety system using Markov analysis approach. The proposed model incorporates process demands in conjunction with CCF for the first time and evaluates their impacts on the reliability quantification of safety systems without automatic diagnostics. The reliability of the Markov model is quantified by considering the Probability of Failure on Demand (PFD) as a measure for low demand systems. The safety performance of the model is analysed using Hazardous Event Frequency (HEF) to evaluate the frequency of entering a hazardous state that will lead to an accident if the situation is not controlled. The utilisation of Markov model for a simple case study of a pressure protection system is demonstrated and it is shown that the proposed approach gives a sufficiently accurate result for all demand rates, durations, component failure rates and corresponding repair rates for low demand mode of operation. The Markov model proposed in this paper assumes the absence of automatic diagnostics, along with multiple stage repair strategy for CCFs and restoration of the system from hazardous state to the "as good as new" state. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  19. Engineering a safe landing: engaging medical practitioners in a systems approach to patient safety. (United States)

    Brand, C; Ibrahim, J; Bain, C; Jones, C; King, B


    Several event studies, including the Australian Safety and Quality in Healthcare Study, emphasize gaps in safety for hospitalized patients. It is now recognized that system-based factors contribute significantly to risk of adverse events and this has led to a shift in focus of patient safety from the autonomous responsibility of medical clinicians to a systems-based approach. The aim of this study was to determine medical practitioner awareness of, level of engagement in and barriers to engagement in a systems approach to patient safety and quality. Information from acute and subacute care medical practitioners at a metropolitan public hospital was collected within an anonymous structured electronic survey, a discussion group and key informant interviews. There were 73 survey respondents (response rate 7.6%). Fifty-one (69.9%) were unaware of the Institute of Medicine report 'To Err is human'. Thirty-six (49.3%) were unaware of the Australian Quality in Healthcare Study and 12 (16.4%) had read the article. There was a positive relation identified between awareness and seniority. There was a low level of participation in systems-focused quality and safety activities and limited understanding of the role of systems in medical error causation. There was uncertainty about the changing role of medical practitioners in patient safety and perceived lack of skills to effectively engage with hospital management about safety and quality issues. Several factors are limiting engagement of medical practitioners in a systems approach to patient safety. Increased educational support is needed and may be best focused within clinical effectiveness activities pertinent to practitioner interest and expertise.

  20. Context factors affecting design and operation of Food Safety Management Systems in the fresh produce chain

    NARCIS (Netherlands)

    Kirezieva, K.K.; Nanyunja, J.; Jacxsens, L.; Vorst, van der J.G.A.J.; Uyttendaele, M.; Luning, P.A.


    Recent food-borne outbreaks and cases of non-compliances to maximum residue limits of pesticides, indicated that food safety management systems (FSMS) in fresh produce chain are not yet performing in a satisfactory manner. However, the system output is not only dependent on the system design and

  1. 78 FR 71036 - Pipeline Safety: Random Drug Testing Rate; Contractor Management Information System Reporting... (United States)


    ...; Contractor Management Information System Reporting; and Obtaining Drug and Alcohol Management Information System Sign-In Information AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... Operators to Report Contractor Management Information System (MIS) Data; and New Method for Operators to...

  2. Role of a quality management system in improving patient safety - laboratory aspects. (United States)

    Allen, Lynn C


    The aim of this study is to describe how implementation of a quality management system (QMS) based on ISO 15189 enhances patient safety. A literature review showed that several European hospitals implemented a QMS based on ISO 9001 and assessed the impact on patient safety. An Internet search showed that problems affecting patient safety have occurred in a number of laboratories across Canada. The requirements of a QMS based on ISO 15189 are outlined, and the impact of the implementation of each requirement on patient safety is summarized. The Quality Management Program - Laboratory Services in Ontario is briefly described, and the experience of Ontario laboratories with Ontario Laboratory Accreditation, based on ISO 15189, is outlined. Several hospitals that implemented ISO 9001 reported either a positive impact or no impact on patient safety. Patient safety problems in Canadian laboratories are described. Implementation of each requirement of the QMS can be seen to have a positive effect on patient safety. Average laboratory conformance on Ontario Laboratory Accreditation is very high, and laboratories must address and resolve any nonconformities. Other standards, practices, and quality requirements may also contribute to patient safety. Implementation of a QMS based on ISO 15189 provides a solid foundation for quality in the laboratory and enhances patient safety. It helps to prevent patient safety issues; when such issues do occur, effective processes are in place for investigation and resolution. Patient safety problems in Canadian laboratories might have been prevented had effective QMSs been in place. Ontario Laboratory Accreditation has had a positive impact on quality in Ontario laboratories. Copyright © 2013 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

  3. Safety Design Strategy for the Advanced Test Reactor Emergency Firewater Injection System Replacement Project

    Energy Technology Data Exchange (ETDEWEB)

    Noel Duckwitz


    In accordance with the requirements of U.S. Department of Energy (DOE) Order 413.3B, “Program and Project Management for the Acquisition of Capital Assets,” safety must be integrated into the design process for new or major modifications to DOE Hazard Category 1, 2, and 3 nuclear facilities. The intended purpose of this requirement involves the handling of hazardous materials, both radiological and chemical, in a way that provides adequate protection to the public, workers, and the environment. Requirements provided in DOE Order 413.3B and DOE Order 420.1B, “Facility Safety,” and the expectations of DOE-STD-1189-2008, “Integration of Safety into the Design Process,” provide for identification of hazards early in the project and use of an integrated team approach to design safety into the facility. This safety design strategy provides the basic safety-in-design principles and concepts that will be used for the Advanced Test Reactor Reliability Sustainment Project. While this project does not introduce new hazards to the ATR, it has the potential for significant impacts to safety-related systems, structures, and components that are credited in the ATR safety basis and are being replaced. Thus the project has been determined to meet the definition of a major modification and is being managed accordingly.

  4. An Uninhabited Aerial System Safety Analysis Model (USAM) Project (United States)

    National Aeronautics and Space Administration — The National Airspace System (NAS) in the United States will become a complex array of commercial and general aviation aircraft, unmanned aircraft systems, reusable...

  5. Enhancing Patient Safety Event Reporting. A Systematic Review of System Design Features. (United States)

    Gong, Yang; Kang, Hong; Wu, Xinshuo; Hua, Lei


    Electronic patient safety event reporting (e-reporting) is an effective mechanism to learn from errors and enhance patient safety. Unfortunately, the value of e-reporting system (a software or web server based platform) in patient safety research is greatly overshadowed by low quality reporting. This paper aims at revealing the current status of system features, detecting potential gaps in system design, and accordingly proposing suggestions for future design and implementation of the system. Three literature databases were searched for publications that contain informative descriptions of e-reporting systems. In addition, both online publicly accessible reporting forms and systems were investigated. 48 systems were identified and reviewed. 11 system design features and their frequencies of occurrence (Top 5: widgets (41), anonymity or confidentiality (29), hierarchy (20), validator (17), review notification (15)) were identified and summarized into a system hierarchical model. The model indicated the current e-reporting systems are at an immature stage in their development, and discussed their future development direction toward efficient and effective systems to improve patient safety.

  6. Safety Management Characteristics Reflected in Interviews at Swedish Nuclear Power Plants: A System Perspective Approach

    Energy Technology Data Exchange (ETDEWEB)

    Salo, Ilkka (Risk Analysis, Social and Decision Research Unit, Dept. of Psychology, Stockholm Univ., Stockholm (Sweden))


    The present study investigated safety management characteristics reflected in interviews with participants from two Swedish nuclear power plants. A document analysis regarding the plants' organization, safety policies, and safety culture work was carried out as well. The participants (n=9) were all nuclear power professionals, and the majority managers at different levels with at least 10 years of nuclear power experience. The interview comprised themes relevant for organizational safety and safety management, such as: organizational structures and organizational change, threats to safety, information feedback and knowledge transfer, safety analysis, safety policy, and accident and incident analysis and reporting. The results were in part modeled to important themes derived from a general system theoretical framework suggested by Svenson and developed by Svenson and Salo in relation to studies of 'non-nuclear' safety organizations. A primer to important features of the system theoretical framework is presented in the introductory chapter. The results from the interviews generated interesting descriptions about nuclear safety management in relation to the above themes. Regarding organizational restructuring, mainly centralizations of resources, several examples of reasons for the restructuring and related benefits for this centralization of resources were identified. A number of important reminders that ought to be considered in relation to reorganization were also identified. Regarding threats to the own organization a number of such was interpreted from the interviews. Among them are risks related to generation and competence change-over and risks related to outsourcing of activities. A thorough picture of information management and practical implications related to this was revealed in the interviews. Related to information feedback is the issue of organizational safety indicators and safety indicators in general. The interview answers indicated

  7. A novel series connected batteries state of high voltage safety monitor system for electric vehicle application. (United States)

    Jiaxi, Qiang; Lin, Yang; Jianhui, He; Qisheng, Zhou


    Batteries, as the main or assistant power source of EV (Electric Vehicle), are usually connected in series with high voltage to improve the drivability and energy efficiency. Today, more and more batteries are connected in series with high voltage, if there is any fault in high voltage system (HVS), the consequence is serious and dangerous. Therefore, it is necessary to monitor the electric parameters of HVS to ensure the high voltage safety and protect personal safety. In this study, a high voltage safety monitor system is developed to solve this critical issue. Four key electric parameters including precharge, contact resistance, insulation resistance, and remaining capacity are monitored and analyzed based on the equivalent models presented in this study. The high voltage safety controller which integrates the equivalent models and control strategy is developed. By the help of hardware-in-loop system, the equivalent models integrated in the high voltage safety controller are validated, and the online electric parameters monitor strategy is analyzed and discussed. The test results indicate that the high voltage safety monitor system designed in this paper is suitable for EV application.

  8. Implementation of child safety and health management system by means of FMEA method

    Directory of Open Access Journals (Sweden)

    B. Akbari Neisiani


    Full Text Available Every year, many accidents leading to physical injuries in kindergartens, indicates that a very large percentage of them are related to the safety concerns and lack of hygiene in these places. Families, due to their busy life style and working hours and also children needs of preschool education, are searching to find most suitable kindergartens for their children. Selecting a kindergarten with various suitable training programs, although very important criteria for selection, but is not sufficient. Indicators such as health, safety and environment issues in these places must be crucial factors in this decision making. Child safety and health management system is an integrated system, derived from health, safety and environmental management regulations which helps the kindergartens complies with relevant regulations to reduce the number of accidents occurrence. The present case study has tried, by using failure modes and effects analysis method and child safety and health management system to find the best practicable indicators to assess the relative impact of different failures in order to identify the parts of the process that are most in need of change. In this regards, 10 semi-governmental kindergartens located in Tehran District 6 of Tehran Municipality, which are supervised by municipality of Tehran were selected and evaluated. The results showed that according to the child safety and health management system and failure modes and effects analysis, all these places need massive infrastructural changes according to the preventive action list in order to be considered a safe and hygienic place for the children.

  9. A Novel Series Connected Batteries State of High Voltage Safety Monitor System for Electric Vehicle Application

    Directory of Open Access Journals (Sweden)

    Qiang Jiaxi


    Full Text Available Batteries, as the main or assistant power source of EV (Electric Vehicle, are usually connected in series with high voltage to improve the drivability and energy efficiency. Today, more and more batteries are connected in series with high voltage, if there is any fault in high voltage system (HVS, the consequence is serious and dangerous. Therefore, it is necessary to monitor the electric parameters of HVS to ensure the high voltage safety and protect personal safety. In this study, a high voltage safety monitor system is developed to solve this critical issue. Four key electric parameters including precharge, contact resistance, insulation resistance, and remaining capacity are monitored and analyzed based on the equivalent models presented in this study. The high voltage safety controller which integrates the equivalent models and control strategy is developed. By the help of hardware-in-loop system, the equivalent models integrated in the high voltage safety controller are validated, and the online electric parameters monitor strategy is analyzed and discussed. The test results indicate that the high voltage safety monitor system designed in this paper is suitable for EV application.

  10. The application of systems approach for road safety policy making, Deliverable 8.1 of the H2020 project SafetyCube (Safety CaUsation, Benefits and Efficiency).

    NARCIS (Netherlands)

    Filtness, A. Thomas, P. Talbot, R. Quigley, C. Papadimitriou, E. Yannis, G. Theofilatos, A. Aigner-Breuss, E. Kaiser, S. Machata, K. Weijermars, W.A.M. Schagen, I.N.L.G. van & Hermitte, T.


    The present Deliverable (D8.1) describes the co-ordination of the analysis of risks and measures using a systems framework within the SafetyCube project. It outlines the results of Task 8.1 of Work Package (WP) 8 of SafetyCube. This has involved (i) defining the systems approach to be used within

  11. CESAR cost-efficient methods and processes for safety-relevant embedded systems

    CERN Document Server

    Wahl, Thomas


    The book summarizes the findings and contributions of the European ARTEMIS project, CESAR, for improving and enabling interoperability of methods, tools, and processes to meet the demands in embedded systems development across four domains - avionics, automotive, automation, and rail. The contributions give insight to an improved engineering and safety process life-cycle for the development of safety critical systems. They present new concept of engineering tools integration platform to improve the development of safety critical embedded systems and illustrate capacity of this framework for end-user instantiation to specific domain needs and processes. They also advance state-of-the-art in component-based development as well as component and system validation and verification, with tool support. And finally they describe industry relevant evaluated processes and methods especially designed for the embedded systems sector as well as easy adoptable common interoperability principles for software tool integratio...

  12. Forklift safety, traffic engineering and intelligent transport systems: a case study. (United States)

    Horberry, Tim; Larsson, Tore J; Johnston, Ian; Lambert, John


    This paper details a forklift safety demonstration project undertaken at two manufacturing sites in Victoria, Australia. The purpose of the work was both to help improve safety at the two sites, and, more broadly, to develop, help implement and evaluate a series of human-centred design interventions involving vehicles and pedestrian workers. The 'before' and 'after' case study presented here summarises the background to the research and introduces the test sites. Thereafter, it describes the overall nature of the safety interventions proposed and introduces the methods developed to assess safety. For the traffic engineering interventions, positive safety results were found in terms of reductions in the number of potentially hazardous interactions involving forklifts. Similarly, for the vehicle interventions, the research found that forklift drivers and managers considered the newly developed and installed Intelligent Transport Systems to be broadly acceptable in operational conditions, and the systems' intended safety benefits were well understood. The results are discussed and conclusions are drawn regarding human factors aspects of forklift safety.

  13. Engaging Employees: The Importance of High-Performance Work Systems for Patient Safety. (United States)

    Etchegaray, Jason M; Thomas, Eric J


    To develop and test survey items that measure high-performance work systems (HPWSs), report psychometric characteristics of the survey, and examine associations between HPWSs and teamwork culture, safety culture, and overall patient safety grade. We reviewed literature to determine dimensions of HPWSs and then asked executives to tell us which dimensions they viewed as most important for safety and quality. We then created a HPWSs survey to measure the most important HPWSs dimensions. We administered an anonymous, electronic survey to employees with direct patient care working at a large hospital system in the Southern United States and looked for linkages between HPWSs, culture, and outcomes. Similarities existed for the HPWS practices viewed as most important by previous researchers and health-care executives. The HPWSs survey was found to be reliable, distinct from safety culture and teamwork culture based on a confirmatory factor analysis, and was the strongest predictor of the extent to which employees felt comfortable speaking up about patient safety problems as well as patient safety grade. We used information from a literature review and executive input to create a reliable and valid HPWSs survey. Future research needs to examine whether HPWSs is associated with additional safety and quality outcomes.

  14. A study to develop the domestic functional requirements of the specific safety systems of CANDU

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Man Woong [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of); Lee, Jae Young; Park, Kun Chul [Handong Global Univ., Pohang (Korea, Republic of)] (and others)


    The present research has been made to develop and review critically the functional requirements of the specific safety systems of CANDU such as SDS-1, SDS2, ECCS, and containment. Based on R documents for this, a systematic study was made to develop the domestic regulation statements. Also, the conventional laws are carefully reviewed to see the compatibility to CANDU. Also, the safety assessment method for CANDU was studied by reviewing C documents and recommendation of IAEA. Through the present works, the vague policy in the CANDU safety regulation is cleaning up in a systematic form and a new frame to measure the objective risk of nuclear power plants was developed.

  15. A study to develop the domestic functional requirements of the specific safety systems of CANDU

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Man Woong; Lee, Jae Young; Bang, Kwang Hyun [Handong Global Univ., Pohang (Korea, Republic of)] (and others)


    The present research has been made to develop and review critically the functional requirements of the specific safety systems of CANDU such as SOS-1, SOS-2, ECCS and containment. Based on R documents for this, a systematic study was made to develop the domestic regulation statements. Also, the conventional laws are carefully reviewed to see the compatibility to CANDU. Also, the safety assessment method for CANDU was studied by reviewing C documents and recommendation of IAEA. Through the present works, the vague policy in the CANDU safety regulation is cleaning up in a systematic form and a new frame to measure the objective risk of nuclear power plants was developed.

  16. Control of AWD System for Vehicle Performance and Safety

    Directory of Open Access Journals (Sweden)

    Jung Hojin


    Full Text Available AWD (All-Wheel Drive system transfers drive force to all wheels so that it can help vehicle escape low mu surface or climb hill more conveniently. Recently, AWD system for on road vehicle has become popular to improve vehicle driving performance. However, there has not been enough research of applying AWD system for vehicle stability especially for lateral movement. Compared with ESC (Electronic Stability Control, AWD system does not cause any inconveniences to the driver because it controls vehicle only by distributing front and rear drive torque, without using brake. By allowing slipping/locking of wet clutch inside the transfer case, AWD system can distribute different amount of torque between front and rear axle. This paper introduces modelling of AWD system and suggests the control of AWD system based on peak slip ratio and slip angle at which tyre saturates. Carsim based vehicle simulation results of AWD controller is presented.

  17. The Effect of Quality Tracing System on Safety of Agricultural Product

    Directory of Open Access Journals (Sweden)

    Jun Zhao


    Full Text Available Frequent occurrence of food safety incidents in recent years has made analyzing safety of agricultural product in view of contract theory become academic research focus. Based on incentive theory, in this paper we establish a static game under the condition of asymmetric information and analyze how the “company + farmer” contract is influenced by a complete quality tracing system composed of ex-ante inspection and ex-post traceability. Meanwhile, we find out that a complete quality tracing system can increase the safety level of agricultural product and that ex-ante inspection and ex-post traceability can replace each other in the process. Finally, we put forward policy suggestion for the policy-maker to solve the problem of food safety.

  18. Study on development of education model and its evaluation system for radiation safety

    CERN Document Server

    Seo, K W; Nam, Y M


    As one of the detailed action strategy of multi object preparedness for strengthening of radiation safety management by MOST, this project was performed, in order to promote the safety culture for user and radiation worker through effective education program. For the prevention of radiological accident and effective implementation of radiation safety education and training, this project has been carried out the development of education model and its evaluation system on radiation safety. In the development of new education model, education course was classified; new and old radiation worker, temporary worker, lecturer and manager. The education model includes the contents of expanding the education opportunity and workplace training. In the development of evaluation system, the recognition criteria for commission-education institute and inside-education institute which should establish by law were suggested for evaluation program. The recognition criteria contains classification, student, method, facilities, ...

  19. A cloud medication safety support system using QR code and Web services for elderly outpatients. (United States)

    Tseng, Ming-Hseng; Wu, Hui-Ching


    Drug is an important part of disease treatment, but medication errors happen frequently and have significant clinical and financial consequences. The prevalence of prescription medication use among the ambulatory adult population increases with advancing age. Because of the global aging society, outpatients need to improve medication safety more than inpatients. The elderly with multiple chronic conditions face the complex task of medication management. To reduce the medication errors for the elder outpatients with chronic diseases, a cloud medication safety supporting system is designed, demonstrated and evaluated. The proposed system is composed of a three-tier architecture: the front-end tier, the mobile tier and the cloud tier. The mobile tier will host the personalized medication safety supporting application on Android platforms that provides some primary functions including reminders for medication, assistance with pill-dispensing, recording of medications, position of medications and notices of forgotten medications for elderly outpatients. Finally, the hybrid technology acceptance model is employed to understand the intention and satisfaction level of the potential users to use this mobile medication safety support application system. The result of the system acceptance testing indicates that this developed system, implementing patient-centered services, is highly accepted by the elderly. This proposed M-health system could assist elderly outpatients' homecare in preventing medication errors and improving their medication safety.

  20. Rapid prototyping of the Central Safety System for Nuclear Risk in ITER

    Energy Technology Data Exchange (ETDEWEB)

    Scibile, L. [ITER Organization, CS 90 046, St. Paul-lez-Durance, Cedex (France); Ambrosino, G. [Consorzio CREATE, Universita degli Studi di Napoli Federico II, via Claudio 21, 80125, Napoli (Italy); De Tommasi, G., E-mail: detommas@unina.i [Consorzio CREATE, Universita degli Studi di Napoli Federico II, via Claudio 21, 80125, Napoli (Italy); Pironti, A. [Consorzio CREATE, Universita degli Studi di Napoli Federico II, via Claudio 21, 80125, Napoli (Italy)


    The Central Safety System for Nuclear Risk (CSS-N) coordinates the safety control systems to ensure nuclear safety for the ITER complex. Since the CSS-N is a safety critical system, its validation and commissioning play a very important role; in particular the required level of reliability must be demonstrated. In such a scenario, it is strongly recommended to use modeling and simulation tools since the early design phase. Indeed, the modeling tools will help in the definition of the control system requirements. Furthermore the models can than be used for the rapid prototyping of the safety system. Hardware-in-the-loop simulations can also be performed in order to assess the performance of the control hardware against a plant simulator. The proposed approach relies on the availability of a plant simulator to develop the prototype of the control system. This paper introduces the methodology used to design and develop both the CSS-N Oriented Plant Simulator and the CSS-N Prototype.

  1. Quality and Safety Education for Nurses (QSEN): The Key is Systems Thinking. (United States)

    Dolansky, Mary A; Moore, Shirley M


    Over a decade has passed since the Institute of Medicine's reports on the need to improve the American healthcare system, and yet only slight improvement in quality and safety has been reported. The Quality and Safety Education for Nurses (QSEN) initiative was developed to integrate quality and safety competencies into nursing education. The current challenge is for nurses to move beyond the application of QSEN competencies to individual patients and families and incorporate systems thinking in quality and safety education and healthcare delivery. This article provides a history of QSEN and proposes a framework in which systems thinking is a critical aspect in the application of the QSEN competencies. We provide examples of how using this framework expands nursing focus from individual care to care of the system and propose ways to teach and measure systems thinking. The conclusion calls for movement from personal effort and individual care to a focus on care of the system that will accelerate improvement of healthcare quality and safety.

  2. Bayesian Statistics and Uncertainty Quantification for Safety Boundary Analysis in Complex Systems (United States)

    He, Yuning; Davies, Misty Dawn


    The analysis of a safety-critical system often requires detailed knowledge of safe regions and their highdimensional non-linear boundaries. We present a statistical approach to iteratively detect and characterize the boundaries, which are provided as parameterized shape candidates. Using methods from uncertainty quantification and active learning, we incrementally construct a statistical model from only few simulation runs and obtain statistically sound estimates of the shape parameters for safety boundaries.


    Directory of Open Access Journals (Sweden)

    N. G. Ptitsyna


    Full Text Available Magnetic fields produced by electric drive vehicles may break electromagnetic safety. For electromagnetic safety and electromagnetic compatibility knowledge about characteristics and sources of magnetic fields in the electric transport is necessary. The article deals with analysis of available data about magnetic fields in electric cars and comparison with results of our measurements carried out in the other types of electrified transport systems.

  4. The safety assurance method of railway control systems using object oriented languages (United States)

    Sumiła, Marek; Lewiński, Andrzej


    The paper deals with introduction of safety rules to the software designed for railway control systems. The basic assumption is related to software designed using high level language UML with possibility of modelling, verification, functional testing and simulation in CASE environment. The object methodology - the base of UML regards the software implementation with respect to safety and real time control corresponding to UIC recommendations and CENELEC standards.

  5. Development of safety and reliability prediction methodology for aircraft systems with common-cause failures


    Nam, G. W.


    A methodology has been developed for predicting aircraft safety and reliability incorporating both C.C.F.s(Common-Cause Failures), and phased missions. Failure behaviour of an aircraft, or its systems due to both independent failures and C.C.F.s are modelled by the Markov process, and simulated using Monte Carlo method with the robust variance reduction techniques. Prediction of safety and reliability is made through discrete-event simulation of aircraft operations. Validati...

  6. Urban traffic safety analysis and assessment system based on GIS: system design, key techniques and implementation strategy (United States)

    Du, Peijun; Pei, Jianzhong; Chen, Xiaowei; Yan, Zhigang


    As the most important technical support to digital transportation and intelligent transportation system (ITS), Geographical Information System (GIS) has become an important tool for traffic safety assessment, management and accident prevention. In this paper, the key techniques, system design method and implementation strategy of Traffic Safety Analysis and Assessment System (TSAAS) is investigated based on the integration of GIS and traffic safety models. TSAAS takes road segment as basic units and uses node sets and directed edge sets to describe road network. Event driven spatial data model is adopted to organize information about traffic accidents in order to link accidents with road network data. In order to solve the problem of data storage, Microsoft SQL Server2000 is used as the basic database platform and SuperMap SDX+ large spatial database engine is used. Traffic safety analysis modeling is usually based on many random accident events, and the results are expressed by certain numerical criteria. Taking two typical traffic safety models: black point model and traffic safety assessment model as examples, the integration of traffic models with GIS is explored in detail. Finally the implementation strategy of TSAAS is investigated, and the secondary development scheme based on ComGIS product, SuperMap Objects, is recommended.

  7. Possible scenarios for a safety upgrade of the ventilation system

    CERN Document Server

    Inigo-Golfin, J


    This paper/presentation describes the existing LHC ventilation (HVAC) system, the design principle followed for the LEP Project and the modifications implemented for the LHC Project. A discussion on possible referential standards to compare the existing system with is presented and possible axes for its improvement, based on these referentials, are discussed. Finally, some recommendations are given based on the system's present capabilities and the estimated investment necessary to achieve compliance to the referentials chosen.

  8. Environment, safety, and health information technology systems integration.

    Energy Technology Data Exchange (ETDEWEB)

    Hendrickson, David A.; Bayer, Gregory W.


    The ES&H Information Systems department, motivated by the numerous isolated information technology systems under its control, undertook a significant integration effort. This effort was planned and executed over the course of several years and parts of it still continue today. The effect was to help move the ES&H Information Systems department toward integration with the corporate Information Solutions and Services center.

  9. Improving patient safety incident reporting systems by focusing upon feedback - lessons from English and Welsh trusts. (United States)

    Wallace, Louise M; Spurgeon, Peter; Benn, Jonathan; Koutantji, Maria; Vincent, Charles


    This paper describes practical implications and learning from a multi-method study of feedback from patient safety incident reporting systems. The study was performed using the Safety Action and Information Feedback from Incident Reporting model, a model of the requirements of the feedback element of a patient safety incident reporting and learning system, derived from a scoping review of research and expert advice from world leaders in safety in high-risk industries. We present the key findings of the studies conducted in the National Health Services (NHS) trusts in England and Wales in 2006. These were a survey completed by risk managers for 351 trusts in England and Wales, three case studies including interviews with staff concerning an example of good practice feedback and an audit of 90 trusts clinical risk staff newsletters. We draw on an Expert Workshop that included 71 experts from the NHS, from regulatory bodies in health care, Royal Colleges, Health and Safety Executive and safety agencies in health care and high-risk industries (commercial aviation, rail and maritime industries). We draw recommendations of enduring relevance to the UK NHS that can be used by trust staff to improve their systems. The recommendations will be of relevance in general terms to health services worldwide.

  10. A smartphone-based driver safety monitoring system using data fusion. (United States)

    Lee, Boon-Giin; Chung, Wan-Young


    This paper proposes a method for monitoring driver safety levels using a data fusion approach based on several discrete data types: eye features, bio-signal variation, in-vehicle temperature, and vehicle speed. The driver safety monitoring system was developed in practice in the form of an application for an Android-based smartphone device, where measuring safety-related data requires no extra monetary expenditure or equipment. Moreover, the system provides high resolution and flexibility. The safety monitoring process involves the fusion of attributes gathered from different sensors, including video, electrocardiography, photoplethysmography, temperature, and a three-axis accelerometer, that are assigned as input variables to an inference analysis framework. A Fuzzy Bayesian framework is designed to indicate the driver's capability level and is updated continuously in real-time. The sensory data are transmitted via Bluetooth communication to the smartphone device. A fake incoming call warning service alerts the driver if his or her safety level is suspiciously compromised. Realistic testing of the system demonstrates the practical benefits of multiple features and their fusion in providing a more authentic and effective driver safety monitoring.

  11. Capturing Safety Requirements to Enable Effective Task Allocation Between Humans and Automaton in Increasingly Autonomous Systems (United States)

    Neogi, Natasha A.


    There is a current drive towards enabling the deployment of increasingly autonomous systems in the National Airspace System (NAS). However, shifting the traditional roles and responsibilities between humans and automation for safety critical tasks must be managed carefully, otherwise the current emergent safety properties of the NAS may be disrupted. In this paper, a verification activity to assess the emergent safety properties of a clearly defined, safety critical, operational scenario that possesses tasks that can be fluidly allocated between human and automated agents is conducted. Task allocation role sets were proposed for a human-automation team performing a contingency maneuver in a reduced crew context. A safety critical contingency procedure (engine out on takeoff) was modeled in the Soar cognitive architecture, then translated into the Hybrid Input Output formalism. Verification activities were then performed to determine whether or not the safety properties held over the increasingly autonomous system. The verification activities lead to the development of several key insights regarding the implicit assumptions on agent capability. It subsequently illustrated the usefulness of task annotations associated with specialized requirements (e.g., communication, timing etc.), and demonstrated the feasibility of this approach.

  12. A Method for Cyber-Physical System Behavior Modeling and Safety Verification Based on Extended Hybrid System Description Language

    Directory of Open Access Journals (Sweden)

    Tuo Ming Fu


    Full Text Available The safety of Cyber-physical system(CPS is up to its behavior, and it is a key property for CPS to be applied in critical application fields. A method for CPS behavior modeling and safety verification is put forward in this paper. The behavior model of CPS is described by extended hybrid system description language(EHYSDEL. The formal definition of hybrid program(HP is given, and the behavior model is transformed to HP based on the definition. The safety of CPS is verified by inputting the HP to KeYmarea. The advantage of the approach is that it models CPS intuitively and verify it’s safety strictly avoiding the state space explosion

  13. A model of Occupational Safety and Health Management System (OSHMS) for promoting and controlling health and safety in textile industry. (United States)

    Manimaran, S; Rajalakshmi, R; Bhagyalakshmi, K


    The development of Occupational Safety and Health Management System in textile industry will rejuvenate the workers and energize the economy as a whole. In India, especially in Tamil Nadu, approximately 1371 textile business is running with the help of 38,461 workers under Ginning, Spinning, Weaving, Garment and Dyeing sectors. Textile industry of contributes to the growth of Indian economy but it fails to foster education and health as key components of human development and help new democracies. The present work attempts to measure and develop OSHMS which reduce the hazards and risk involved in textile industry. Among all other industries textile industry is affected by enormous hazards and risk because of negligence by management and Government. It is evident that managements are not abiding by law when an accident has occurred. Managements are easily deceiving workers and least bothered about the Quality of Work Life (QWL). A detailed analysis of factors promoting safety and health to the workers has been done by performing confirmatory factor analysis, evaluating Risk Priority Number and the framework of OHMS has been conceptualized using Structural Equation Model. The data have been collected using questionnaire and interview method. The study finds occupation health for worker in Textile industry is affected not only by safety measure but also by technology and management. The work shows that difficulty in identifying the cause and effect of hazards, the influence of management in controlling and promoting OSHMS under various dimensions. One startling fact is existence of very low and insignificance correlation between health factors and outcome.

  14. Measurability and Safety Verification for Stochastic Hybrid Systems

    DEFF Research Database (Denmark)

    Fränzle, Martin; Hahn, Ernst Moritz; Hermanns, Holger


    Dealing with the interplay of randomness and continuous time is important for the formal verification of many real systems. Considering both facets is especially important for wireless sensor networks, distributed control applications, and many other systems of growing importance. An important...... traditional design and verification goal for such systems is to ensure that unsafe states can never be reached. In the stochastic setting, this translates to the question whether the probability to reach unsafe states remains tolerable. In this paper, we consider stochastic hybrid systems where the continuous...... method that establishes safe upper bounds on reachability probabilities. To arrive there requires us to solve semantic intricacies as well as practical problems. In particular, we show that measurability of a complete system follows from the measurability of its constituent parts. On the practical side...

  15. Validation study on reliability analysis of main safety system in Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Nam Jin; Cho, Chang Keun; Kim, Yong Hui; Kim, Tae Hyeong; Hong, Seo Kee; Park, Keon Woo; Park, Chang Jea [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Cheong, Woo Sik [Institute for Advanced Engineering, Yongin (Korea, Republic of); Park, Moon Kyu [KEPRI, Taejon (Korea, Republic of)


    The scope and contents of this validation study are to review the design changes of the four main safety systems in Wolsong 2/3/4 Nuclear Power Plants, to review the consideration of the above design changes in the AECL reports, the structure of fault trees, and the data base used in the quantification of the fault trees, to quantify the unavailabilities of main safety systems and check them if they meet the requirements, and to recommend desirable design changes in the emergency core cooling system to reduce the unavailability.

  16. Preliminary assessment of a combined passive safety system for typical 3-loop PWR CPR1000

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Zijiang; Shan, Jianqiang, E-mail:; Gou, Junli


    Highlights: • A combined passive safety system was placed on a typical 3-loop PWR CPR1000. • Three accident analyses show the three different accident mitigation methods of the passive safety system. • The three mitigation methods were proved to be useful. - Abstract: As the development of the nuclear industry, passive technology turns out to be a remarkable characteristic of advanced nuclear power plants. Since the 20th century, much effort has been given to the passive technology, and a number of evolutionary passive systems have developed. Thoughts have been given to upgrade the existing reactors with passive systems to meet stricter safety demands. In this paper, the CPR1000 plant, which is one kind of mature pressurized water reactor plants in China, is improved with some passive systems to enhance safety. The passive systems selected are as follows: (1) the reactor makeup tank (RMT); (2) the advanced accumulator (A-ACC); (3) the in-containment refueling water storage tank (IRWST); (4) the passive emergency feed water system (PEFS), which is installed on the secondary side of SGs; (5) the passive depressurization system (PDS). Although these passive components is based on the passive technology of some advanced reactors, their structural and trip designs are adjusted specifically so that it could be able to mitigate accidents of the CPR1000. Utilizing the RELAP5/MOD3.3 code, accident analyses (small break loss of coolant accident, large break loss of coolant accident, main feed water line break accident) of this improved CPR1000 plant were presented to demonstrate three different accident mitigation methods of the safety system and to test whether the passive safety system preformed its function well. In the SBLOCA, all components of the passive safety system were put into work sequentially, which prevented the core uncover. The LBLOCA analysis illustrates the contribution of the A-ACCs whose small-flow-rate injection can control the maximum cladding

  17. The effect of Health, Safety and Environment Management System (HSE-MS on the improvement of safety performance indices in Urea and Ammonia Kermanshah Petrochemical Company

    Directory of Open Access Journals (Sweden)

    M. S. Poursoleiman


    Full Text Available Introduction: Work-related accidents may cause damage to people, environment and lead to waste of time and money. Health, Safety and Environment Management System has been developed in order to reduce accidents. This study aimed to investigate the effect of implementation of this system on reduction of the accidents and its consequences and also on the safety performance indices in Kermanshah Petrochemical Company. Material and Method: In this study, records of accidents were collected by OSHA incident report form 301 over 4 years. Following, the mean annual accidents and its consequences and safety performance indices were calculated and reported. Then, using statistical analysis, the impacts of two years implementation of this system on the accidents and its consequences and safety performance indices were evaluated. Result: The results showed that the implementation of HSE system was significantly correlated with Frequency Severity Indicator, Accident Severity Rate, lost days, minor accidents and total incidents (P-value 0.05. Conclusion: The implementation of Health, Safety and the Environment Management System caused a reduction in accidents and its consequences and most of the safety performance indices in the entire process cycle of Kermanshah Petrochemical Company. Overall, safety condition has been improved considerably.

  18. Context-aware system for pre-triggering irreversible vehicle safety actuators. (United States)

    Böhmländer, Dennis; Dirndorfer, Tobias; Al-Bayatti, Ali H; Brandmeier, Thomas


    New vehicle safety systems have led to a steady improvement of road safety and a reduction in the risk of suffering a major injury in vehicle accidents. A huge leap forward in the development of new vehicle safety systems are actuators that have to be activated irreversibly shortly before a collision in order to mitigate accident consequences. The triggering decision has to be based on measurements of exteroceptive sensors currently used in driver assistance systems. This paper focuses on developing a novel context-aware system designed to detect potential collisions and to trigger safety actuators even before an accident occurs. In this context, the analysis examines the information that can be collected from exteroceptive sensors (pre-crash data) to predict a certain collision and its severity to decide whether a triggering is entitled or not. A five-layer context-aware architecture is presented, that is able to collect contextual information about the vehicle environment and the actual driving state using different sensors, to perform reasoning about potential collisions, and to trigger safety functions upon that information. Accident analysis is used in a data model to represent uncertain knowledge and to perform reasoning. A simulation concept based on real accident data is introduced to evaluate the presented system concept. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Model-based safety analysis of a control system using Simulink and Simscape extended models

    Directory of Open Access Journals (Sweden)

    Shao Nian


    Full Text Available The aircraft or system safety assessment process is an integral part of the overall aircraft development cycle. It is usually characterized by a very high timely and financial effort and can become a critical design driver in certain cases. Therefore, an increasing demand of effective methods to assist the safety assessment process arises within the aerospace community. One approach is the utilization of model-based technology, which is already well-established in the system development, for safety assessment purposes. This paper mainly describes a new tool for Model-Based Safety Analysis. A formal model for an example system is generated and enriched with extended models. Then, system safety analyses are performed on the model with the assistance of automation tools and compared to the results of a manual analysis. The objective of this paper is to improve the increasingly complex aircraft systems development process. This paper develops a new model-based analysis tool in Simulink/Simscape environment.

  20. Health and safety. Preliminary comparative assessment of the satellite power system (SPS) and other energy alternatives

    Energy Technology Data Exchange (ETDEWEB)

    Habegger, L.J.; Gasper, J.R.; Brown, C.D.


    Existing data on the health and safety risks of a satellite power system and four electrical generation systems are analyzed: a combined-cycle coal power system with a low-Btu gasifier and open-cycle gas turbine, a fission power system with fuel reprocessing, a central-station, terrestrial, solar-photovoltaic power system, and a first-generation design for a fusion power system. The systems are compared on the basis of expected deaths and person-days lost per year associated with 1000 MW of average electricity generation and the number of health and safety risks that are identified as potentially significant but unquantifiable. The appendices provide more detailed information on risks, uncertainties, additional research needed, and references for the identified impacts of each system.

  1. Airbag 2000: 5th international symposium on sophisticated car occupant safety systems

    Energy Technology Data Exchange (ETDEWEB)

    Ziegahn, K.F. (ed.)


    Modern concepts for the protection of passengers in vehicles provide the optimal degree of safety. The most well known and technically mature system is the airbag, which uses chemical gas generators, for which the dependability and service life demands are significant. All features of the system must be directly appropriate to the profile of the passenger. (AKF)

  2. Feminist Heuristics: Transforming the Foundation of Food Quality and Safety Assurance Systems (United States)

    Kimura, Aya Hirata


    Food safety and quality assurance systems have emerged as a key mechanism of food governance in recent years and are also popular among alternative agrofood movements, such as the organic and fair trade movements. Rural sociologists have identified many problems with existing systems, including corporate cooptation, the marginalization of small…

  3. The electronic security partnership of safety/security and information systems departments. (United States)

    Yow, J Art


    The ever-changing world of security electronics is reviewed in this article. The author focuses on its usage in a hospital setting and the need for safety/security and information systems departments to work together to protect and get full value from IP systems.

  4. Challenges in Performance of Food Safety Management Systems: A Case of Fish Processing Companies in Tanzania

    NARCIS (Netherlands)

    Kussaga, J.B.; Luning, P.A.; Tiisekwa, B.P.M.; Jacxsens, L.


    This study provides insight for food safety (FS) performance in light of the current performance of core FS management system (FSMS) activities and context riskiness of these systems to identify the opportunities for improvement of the FSMS. A FSMS diagnostic instrument was applied to assess the

  5. 14 CFR 135.128 - Use of safety belts and child restraint systems. (United States)


    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Use of safety belts and child restraint systems. 135.128 Section 135.128 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF.... 213 (49 CFR 571.213)), vest- and harness-type child restraint systems, and lap held child restraints...

  6. Developing a Safety Management System for Fatigue Related Risks in easyJet

    NARCIS (Netherlands)

    Stewart, S.; Koornneef, F.; Akselsson, R.; Turner, C.


    Chapter 5: Developing a Safety Management System for Fatigue Related Risks in easyJet The European Commission HILAS project (Human Integration into the Lifecycle of Aviation Systems - a project supported by the European Commission’s 6th Framework between 2005-2009) was focused on using human factors

  7. Current performance of food safety management systems of dairy processing companies in Tanzania

    NARCIS (Netherlands)

    Kussaga, J.B.; Luning, P.A.; Tisekwa, B.P.M.; Jacxsens, L.


    food safety management system (FSMS)-diagnostic instrument was applied in 22 dairy processing companies to analyse the set-up and operation of core control and assurance activities in view of the risk characteristics of the systems' context. Three clusters of companies were identified differing in

  8. Airport Movement Area Safety System (AMASS) Operational Test, Final Report

    National Research Council Canada - National Science Library

    Dellmyer, Dan


    ...) was to verify the Critical Operational Issues (COT). The AMASS is a runway collision alert system that provides tower air traffic controllers with automated conflict warnings and alerts to reduce the risks of runway collisions...

  9. Extended GTST-MLD for aerospace system safety analysis. (United States)

    Guo, Chiming; Gong, Shiyu; Tan, Lin; Guo, Bo


    The hazards caused by complex interactions in the aerospace system have become a problem that urgently needs to be settled. This article introduces a method for aerospace system hazard interaction identification based on extended GTST-MLD (goal tree-success tree-master logic diagram) during the design stage. GTST-MLD is a functional modeling framework with a simple architecture. Ontology is used to extend the ability of system interaction description in GTST-MLD by adding the system design knowledge and the past accident experience. From the level of functionality and equipment, respectively, this approach can help the technician detect potential hazard interactions. Finally, a case is used to show the method. © 2011 Society for Risk Analysis.

  10. Sensors and Systems to Enhance Aviation Safety Against Weather Hazards


    Mahapatra, Pravas R; Zrnic, Dusan S


    Weather-related factors are among major causes of aviation hazards, passenger discomfort, poor airline schedule-keeping, and poor operating economy. A variety of new high-technology electronic sensors and systems for aviation weather are being developed and installed across the US. The aviation weather monitoring system of the future will be centered around Doppler weather radars which offer the best combination of coverage, resolution, and agility for this purpose, and are able to detect and...

  11. Safety of Systemic Agents for the Treatment of Pediatric Psoriasis. (United States)

    Bronckers, Inge M G J; Seyger, Marieke M B; West, Dennis P; Lara-Corrales, Irene; Tollefson, Megha; Tom, Wynnis L; Hogeling, Marcia; Belazarian, Leah; Zachariae, Claus; Mahé, Emmanuel; Siegfried, Elaine; Philipp, Sandra; Szalai, Zsuzsanna; Vleugels, Ruth Ann; Holland, Kristen; Murphy, Ruth; Baselga, Eulalia; Cordoro, Kelly; Lambert, Jo; Alexopoulos, Alex; Mrowietz, Ulrich; Kievit, Wietske; Paller, Amy S


    Use of systemic therapies for moderate to severe psoriasis in children is increasing, but comparative data on their use and toxicities are limited. To assess patterns of use and relative risks of systemic agents for moderate to severe psoriasis in children. A retrospective review was conducted at 20 centers in North America and Europe, and included all consecutive children with moderate to severe psoriasis who used systemic medications or phototherapy for at least 3 months from December 1, 1990, to September 16, 2014. The minimal core data set included age, sex, severity of psoriasis, systemic interventions, monitoring, adverse events (AEs), and reason for discontinuation. For 390 children (203 girls and 187 boys; mean [SD] age at diagnosis, 8.4 [3.7] years) with psoriasis who used 1 or more systemic medications, the mean interval between diagnosis and starting systemic therapy was 3.0 years. Methotrexate was used by 270 patients (69.2%), biologic agents (primarily etanercept) by 106 (27.2%), acitretin by 57 (14.6%), cyclosporine by 30 (7.7%), fumaric acid esters by 19 (4.9%), and more than 1 medication was used by 73 (18.7%). Of 270 children taking methotrexate, 130 (48.1%) reported 1 or more AEs associated with methotrexate, primarily gastrointestinal (67 [24.8%]). Folic acid 6 days per week (odds ratio, 0.16; 95% CI, 0.06-0.41; P psoriasis.

  12. Establishment of mobile based nuclear safety inspection system

    Energy Technology Data Exchange (ETDEWEB)

    Kim, In Hyeon; Lee, Yoon; Choi, Keun Ho; Lee, Kwang Pyo; Cha, Gi Hyeon; Gook, Cheol Woong; Park, Tae Joo; Kang, Roc Hyeong; Kim, Ji Young; Yoo, Mi Jung [Korea geoSpatial Information and Communication Co., Ltd., Seoul (Korea, Republic of)


    We have developed the mobile-based atomic energy status real time monitoring system and mobile-based atomic energy accident and trouble retrieval system through this study. The mobile-based atomic energy status real time monitoring system is the system enabling its users to monitor nineteen (19) Nuclear Power Plants under operation in the real time based on the PDA(Personal Digital Assistance) via a wireless communication. We have developed the mobile information providing server program and PDA client program for the purpose of providing the atomic energy status information service on the PDA by linking the real time atomic energy status information collected by the computerized technical advisory system for the radiological emergency installed and operated by the KINS. The mobile based atomic energy accident and trouble retrieval system has been developed under the intention of enabling the site inspector to effectively use the past information upon performing the test works at the sites through the local retrieval of past accidents and troubles occurred in the Nuclear Power Plants at the mobile client(PDA). In this regard, we have developed the client program to retrieve the atomic energy accident and trouble status by installing the accident and trouble information database. We also include the function supporting the rapid site report through the employees' information retrieval, site status image file transmission, e-mail and SMS(Short Message Service)

  13. Towards a Usability and Error "Safety Net": A Multi-Phased Multi-Method Approach to Ensuring System Usability and Safety. (United States)

    Kushniruk, Andre; Senathirajah, Yalini; Borycki, Elizabeth


    The usability and safety of health information systems have become major issues in the design and implementation of useful healthcare IT. In this paper we describe a multi-phased multi-method approach to integrating usability engineering methods into system testing to ensure both usability and safety of healthcare IT upon widespread deployment. The approach involves usability testing followed by clinical simulation (conducted in-situ) and "near-live" recording of user interactions with systems. At key stages in this process, usability problems are identified and rectified forming a usability and technology-induced error "safety net" that catches different types of usability and safety problems prior to releasing systems widely in healthcare settings.

  14. Measuring safety in aviation : empirical results about the relation between safety outcomes and safety management system processes, operational activities and demographic data

    NARCIS (Netherlands)

    Kaspers, Steffen; Karanikas, Nektarios; Piric, Selma; van Aalst, Robbert; de Boer, Robert Jan; Roelen, Alfred


    A literature review conducted as part of a research project named “Measuring Safety in Aviation – Developing Metrics for Safety Management Systems” revealed several challenges regarding the safety metrics used in aviation. One of the conclusions was that there is limited empirical evidence about the

  15. Mathematical modelling of active safety system functions as tools for development of driverless vehicles (United States)

    Ryazantsev, V.; Mezentsev, N.; Zakharov, A.


    This paper is dedicated to a solution of the issue of synthesis of the vehicle longitudinal dynamics control functions (acceleration and deceleration control) based on the element base of the vehicle active safety system (ESP) – driverless vehicle development tool. This strategy helps to reduce time and complexity of integration of autonomous motion control systems (AMCS) into the vehicle architecture and allows direct control of actuators ensuring the longitudinal dynamics control, as well as reduction of time for calibration works. The “vehicle+wheel+road” longitudinal dynamics control is complicated due to the absence of the required prior information about the control object. Therefore, the control loop becomes an adaptive system, i.e. a self-adjusting monitoring system. Another difficulty is the driver’s perception of the longitudinal dynamics control process in terms of comfort. Traditionally, one doesn’t pay a lot of attention to this issue within active safety systems, and retention of vehicle steerability, controllability and stability in emergency situations are considered to be the quality criteria. This is mainly connected to its operational limits, since it is activated only in critical situations. However, implementation of the longitudinal dynamics control in the AMCS poses another challenge for the developers – providing the driver with comfortable vehicle movement during acceleration and deceleration – while the possible highest safety level in terms of the road grip is provided by the active safety system (ESP). The results of this research are: universal active safety system – AMCS interaction interface; block diagram for the vehicle longitudinal acceleration and deceleration control as one of the active safety system’s integrated functions; ideology of adaptive longitudinal dynamics control, which enables to realize the deceleration and acceleration requested by the AMCS; algorithms synthesised; analytical experiments proving

  16. National Food Safety Systems in the European Union: A Comparative Survey

    Directory of Open Access Journals (Sweden)

    Andreas Hadjigeorgiou


    Full Text Available This paper is a comparative survey of the National Food Safety Systems (NFSS of the European Union (EU Member-States (MS and the Central EU level. The main organizational structures of the NFSS, their legal frameworks, their responsibilities, their experiences, and challenges relating to food safety are discussed. Growing concerns about food safety have led the EU itself, its MS and non-EU countries, which are EU trade-partners, to review and modify their food safety systems. Our study suggests that the EU and 22 out of 27 Member States (MS have reorganized their NFSS by establishing a single food safety authority or a similar organization on the national or central level. In addition, the study analyzes different approaches towards the establishment of such agencies. Areas where marked differences in approaches were seen included the division of responsibilities for risk assessment (RA, risk management (RM, and risk communication (RC. We found that in 12 Member States, all three areas of activity (RA, RM, and RC are kept together, whereas in 10 Member States, risk management is functionally or institutionally separate from risk assessment and risk communication. No single ideal model for others to follow for the organization of a food safety authority was observed; however, revised NFSS, either in EU member states or at the EU central level, may be more effective from the previous arrangements, because they provide central supervision, give priority to food control programs, and maintain comprehensive risk analysis as part of their activities.

  17. A quality control method for nuclear instrumentation and control systems based on software safety prediction (United States)

    Son, Han Seong; Seong, Poong Hyun


    In the case of safety-related applications like nuclear instrumentation and control (NI&C), safety-oriented quality control is required. The objective of this paper is to present a software safety classification method as a safety-oriented quality control tool. Based on this method, we predict the risk (and thus safety) of software items that are at the core of NI&C systems. Then we classify the software items according to the degree of the risk. The method can be used earlier than at the detailed design phase. Furthermore, the method can also be used in all the development phases without major changes. The proposed method seeks to utilize the measures that can be obtained from the safety analysis and requirements analysis. Using the measures proved to be desirable in a few aspects. The authors have introduced fuzzy approximate reasoning to the classification method because experts' knowledge covers the vague frontiers between good quality and bad quality with linguistic uncertainty and fuzziness. Fuzzy Colored Petri Net (FCPN) is introduced in order to offer a formal framework for the classification method and facilitate the knowledge representation, modification, or verification. Through the proposed quality control method, high-quality NI&C systems can be developed effectively and used safely.

  18. A safety assessment methodology applied to CNS/ATM-based air traffic control system

    Energy Technology Data Exchange (ETDEWEB)

    Vismari, Lucio Flavio, E-mail: lucio.vismari@usp.b [Safety Analysis Group (GAS), School of Engineering at University of Sao Paulo (Poli-USP), Av. Prof. Luciano Gualberto, Trav.3, n.158, Predio da Engenharia de Eletricidade, Sala C2-32, CEP 05508-900, Sao Paulo (Brazil); Batista Camargo Junior, Joao, E-mail: joaocamargo@usp.b [Safety Analysis Group (GAS), School of Engineering at University of Sao Paulo (Poli-USP), Av. Prof. Luciano Gualberto, Trav.3, n.158, Predio da Engenharia de Eletricidade, Sala C2-32, CEP 05508-900, Sao Paulo (Brazil)


    In the last decades, the air traffic system has been changing to adapt itself to new social demands, mainly the safe growth of worldwide traffic capacity. Those changes are ruled by the Communication, Navigation, Surveillance/Air Traffic Management (CNS/ATM) paradigm , based on digital communication technologies (mainly satellites) as a way of improving communication, surveillance, navigation and air traffic management services. However, CNS/ATM poses new challenges and needs, mainly related to the safety assessment process. In face of these new challenges, and considering the main characteristics of the CNS/ATM, a methodology is proposed at this work by combining 'absolute' and 'relative' safety assessment methods adopted by the International Civil Aviation Organization (ICAO) in ICAO Doc.9689 , using Fluid Stochastic Petri Nets (FSPN) as the modeling formalism, and compares the safety metrics estimated from the simulation of both the proposed (in analysis) and the legacy system models. To demonstrate its usefulness, the proposed methodology was applied to the 'Automatic Dependent Surveillance-Broadcasting' (ADS-B) based air traffic control system. As conclusions, the proposed methodology assured to assess CNS/ATM system safety properties, in which FSPN formalism provides important modeling capabilities, and discrete event simulation allowing the estimation of the desired safety metric.

  19. [B-BS and occupational health and safety management systems: the SGSL certification]. (United States)

    Calabrese, G; Candura, G


    The social costs deriving from the lack of occupational safety, which nowadays constitute approximately 2.8% of the GDP, tend not to come down despite the regulations, the inspections and the sanctions. The problems may be ascribed both to a shortage of systemic actions and to inappropriate training of the workers. Possible solutions are represented by the adoption of organizational models (D. Lgs. 81 art. 30) and by the implementation of protocols such as the Behavior-Based Safety (B-BS). Organisational and Management Models have been introduced with art. 30 D.Lgs. 81/2008 and with art. 6 D.Lgs. 231/2001. The comparison between their requisites and the ones specified by the OHSAS 18001 standards, confirms the partial overlapping of the Organizational Models with the Occupational Health & Safety Management Systems. Nevertheless such Systems are rarely adopted by Italian companies and their implementation still doesn't grant complete effectiveness. The B-BS protocol is proving to be a tool of extraordinary value to increase the level of safety, especially when used along with the known Health & Safety Management Systems.

  20. Nanoparticles and the blood coagulation system. Part II: safety concerns (United States)

    Ilinskaya, Anna N; Dobrovolskaia, Marina A


    Nanoparticle interactions with the blood coagulation system can be beneficial or adverse depending on the intended use of a nanomaterial. Nanoparticles can be engineered to be procoagulant or to carry coagulation-initiating factors to treat certain disorders. Likewise, they can be designed to be anticoagulant or to carry anticoagulant drugs to intervene in other pathological conditions in which coagulation is a concern. An overview of the coagulation system was given and a discussion of a desirable interface between this system and engineered nanomaterials was assessed in part I, which was published in the May 2013 issue of Nanomedicine. Unwanted pro- and anti-coagulant properties of nanoparticles represent significant concerns in the field of nanomedicine, and often hamper the development and transition into the clinic of many promising engineered nanocarriers. This part will focus on the undesirable effects of engineered nanomaterials on the blood coagulation system. We will discuss the relationship between the physicochemical properties of nanoparticles (e.g., size, charge and hydrophobicity) that determine their negative effects on the blood coagulation system in order to understand how manipulation of these properties can help to overcome unwanted side effects. PMID:23730696

  1. Patient safety reporting systems: sustained quality improvement using a multidisciplinary team and "good catch" awards. (United States)

    Herzer, Kurt R; Mirrer, Meredith; Xie, Yanjun; Steppan, Jochen; Li, Matthew; Jung, Clinton; Cover, Renee; Doyle, Peter A; Mark, Lynette J


    Since 1999, hospitals have made substantial commitments to health care quality and patient safety through individual initiatives of executive leadership involvement in quality, investments in safety culture, education and training for medical students and residents in quality and safety, the creation of patient safety committees, and implementation of patient safety reporting systems. At the Weinberg Surgical Suite at The Johns Hopkins Hospital (Baltimore), a 16-operating-room inpatient/outpatient cancer center, a patient safety reporting process was developed to maximize the usefulness of the reports and the long-term sustainability of quality improvements arising from them. A six-phase framework was created incorporating UHC's Patient Safety Net (PSN): Identify, report, analyze, mitigate, reward, and follow up. Unique features of this process included a multidisciplinary team to review reports, mitigate hazards, educate and empower providers, recognize the identifying/reporting individuals or groups with "Good Catch" awards, and follow up to determine if quality improvements were sustained over time. Good Catch awards have been given in recognition of 29 patient safety hazards identified since 2008; in each of these cases, an initiative was developed to mitigate the original hazard. Twenty-five (86%) of the associated quality improvements have been sustained. Two Good Catch award-winning projects--vials of heparin with an unusually high concentration of the drug that posed a potential overdose hazard and a rapid infusion device that resisted practitioner control--are described in detail. A multidisciplinary team's analysis and mitigation of hazards identified in a patient safety reporting process entailed positive recognition with a Good Catch award, education of practitioners, and long-term follow-up.

  2. Sense and avoid requirements for unmanned aircraft systems using a target level of safety approach. (United States)

    Melnyk, Richard; Schrage, Daniel; Volovoi, Vitali; Jimenez, Hernando


    One of the most critical challenges to full integration of unmanned aircraft systems (UAS) into the National Airspace System (NAS) is the requirement to comply with CFR 14 Part 91.113 to "see and avoid" other aircraft. Various attempts have been made to develop systems to "sense and avoid" other aircraft so UAS can comply with the intent of the regulation. This article proposes a framework to develop effectiveness requirements for any SAA system by linking UAS characteristics and operating environments to midair collision risk quantified by a fatality rate. The framework consists of a target level of safety (TLS) approach using an event tree format. Safety has been identified as the most important consideration in the UAS integration process. While safety can be defined in many ways, the authors propose using a fatality rate metric that follows other statistics used in the industry. This metric allows for the use of a TLS approach to the development of SAA requirements for system certification. Failure to adequately link system requirements to safety could result in the implementation of SAA systems that either do not adequately mitigate the risk associated with UAS operations or are overdesigned, resulting in increased cost and complexity. This article demonstrates the use of the proposed framework to develop specific SAA effectiveness standards based on UAS weight and airspace class combinations. © 2014 Society for Risk Analysis.

  3. Security warning method and system for worker safety during live-line working (United States)

    Jiang, Chilong; Zou, Dehua; Long, Chenhai; Yang, Miao; Zhang, Zhanlong; Mei, Daojun


    Live-line working is an essential part in the operations in an electric power system. Live-line workers are required to wear shielding clothing. Shielding clothing, however, acts as a closed environment for the human body. Working in a closed environment for a long time can change the physiological responses of the body and even endanger personal safety. According to the typical conditions of live-line working, this study synthesizes environmental factors related to shielding clothing and the physiological factors of the body to establish the heart rate variability index RMSSD and the comprehensive security warning index SWI. On the basis of both indices, this paper proposes a security warning method and system for the safety live-line workers. The system can monitor the real-time status of workers during live-line working to provide security warning and facilitate the effective safety supervision by the live operation center during actual live-line working.

  4. The Legitimacy of Safety Management Systems in the Minds of Norwegian Seafarers

    Directory of Open Access Journals (Sweden)

    Bjarne Vandeskog


    Full Text Available All seafarers I have met are concerned with their own safety and all serious shipping companies, national regulatory authorities, unions and larger shipping clients work to improve safety at sea. Formalised risk management systems are at the heart of these efforts, and there is good reason to believe that they have been very successful. One would therefore expect that seafarers had a positive attitude and were committed to their implementation. Empirical data suggests the opposite. During observational fieldworks over the last two and a half years, on eight different ships in Norway, Australia and Malaysia, not one of the observed seafarers expressed mainly positive opinions about the safety management systems imposed on them. The great majority of seafarers whose opinions have been recorded expressed massive negative sentiments. Assuming a Weberian perspective this paper explores how the bureaucratic implementation of such risk management systems may contribute to this picture.

  5. Construction of Traceability System for Quality Safety of Cereal and Oil Products (United States)

    Zheng, Huoguo; Liu, Shihong; Meng, Hong; Hu, Haiyan

    After several significant food safety incident, global food industry and governments in many countries are putting increasing emphasis on establishment of food traceability systems. Food traceability has become an effective way in food quality and safety management. The traceability system for quality safety of cereal and oil products was designed and implemented with HACCP and FMECA method, encoding, information processing, and hardware R&D technology etc, according to the whole supply chain of cereal and oil products. Results indicated that the system provide not only the management in origin, processing, circulating and consuming for enterprise, but also tracing service for customers and supervisor by means of telephone, internet, SMS, touch machine and mobile terminal.

  6. Intelligent transportation systems dependable vehicular communications for improved road safety

    CERN Document Server

    Ferreira, Joaquim; Fonseca, José


    This book presents cutting-edge work on the most challenging research issues concerning intelligent transportation systems (ITS), introducing selected, highly relevant advanced research on scheduling and real-time communication for vehicular networks, as well as fault tolerance, test beds and simulations for ITS. The authors define new architectures that support cooperative sensing in ITS and offer guidance for the development of a reference end-to-end implementation. The presented results allow advanced traffic and travel management strategies to be formulated on the basis of reliable and real-time input data. The effectiveness of these new strategies, together with the proposed systems, is assessed in field trials and via simulations. The chapters in this book detail new research findings, algorithms, protocols, and the development of an implementation platform for ITS that merges and integrates heterogeneous data sources into a common system. In addition, they provide a set of advanced tools for the contro...

  7. Cancer in pregnancy: safety and efficacy of systemic therapies. (United States)

    Boere, Ingrid; Lok, Christianne; Vandenbroucke, Tineke; Amant, Frédéric


    Cancer in pregnancy has become increasingly frequent. It has become clear that for specific cancers under well defined circumstances, oncological treatment in pregnancy can be well tolerated and feasible for both mother and fetus. Continued critical assessment of the available literature and registration of cancer in pregnancy cases and outcomes for mother and child are necessary to work toward implementing optimal cancer treatment during pregnancy. Physiologic changes in pregnancy may alter distribution and efficacy of systemic therapy. Data on systemic therapy including, chemotherapy, hormonal therapy, and targeted therapy during pregnancy are available but incomplete. Outcomes of fetuses exposed to chemotherapy in utero are generally reassuring, but new targeted therapies are mostly discouraged in pregnancy. Cancer treatment during pregnancy is possible, depending on type and timing of systemic therapy and treatment modality. Available data are reassuring with a modest increase in complications such as growth restriction and preterm birth. The effect of new targeted therapies is often still unclear and therefore discouraged.

  8. Accelerator driven systems from the radiological safety point of view

    Indian Academy of Sciences (India)

    Abstract. In the proposed accelerator driven systems (ADS) the possible use of several milliamperes of protons of about 1 GeV incident on high mass targets like the molten lead– bismuth eutectic is anticipated to pose radiological problems that have so far not been encountered by the radiation protection community.

  9. Efficacy and Safety of Midostaurin in Advanced Systemic Mastocytosis

    NARCIS (Netherlands)

    Gotlib, Jason; Kluin-Nelemans, Hanneke C.; George, Tracy I.; Akin, Cem; Sotlar, Karl; Hermine, Olivier; Awan, Farrukh T.; Hexner, Elizabeth; Mauro, Michael J.; Sternberg, David W.; Villeneuve, Matthieu; Labed, Alice Huntsman; Stanek, Eric J.; Hartmann, Karin; Horny, Hans-Peter; Valent, Peter; Reiter, Andreas


    BACKGROUND Advanced systemic mastocytosis comprises rare hematologic neoplasms that are associated with a poor prognosis and lack effective treatment options. The multikinase inhibitor midostaurin inhibits KIT D816V, a primary driver of disease pathogenesis. METHODS We conducted an open-label study

  10. Accelerator driven systems from the radiological safety point of view

    Indian Academy of Sciences (India)


    Nov 27, 2015 ... In the proposed accelerator driven systems (ADS) the possible use of several milliamperes of protons of about 1 GeV incident on high mass targets like the molten lead–bismuth eutectic is anticipated to pose radiological problems that have so far not been encountered by the radiation protection community.

  11. Electronics system design techniques for safety critical applications

    CERN Document Server

    Sterpone, Luca


    Addresses the development of techniques for the evaluation and the hardening of designs implemented on SRAM-based Field Programmable Gate Arrays. This title presents a design methodology solving industrial designer''s needs for implementing electronic systems using SRAM-based FPGAs in critical environments, like the space or avionic ones.

  12. Thermohydraulic safety issues for liquid metal cooled systems

    Energy Technology Data Exchange (ETDEWEB)

    Gerbeth, Gunter; Stefani, Frank [Helmholtz-Zentrum Dresden-Rossendorf (HZDR) e.V., Dresden (Germany). Inst. of Fluid Dynamics; Eckert, Sven


    In this paper recent developments of various techniques for single-phase and two-phase flow measurements with relevance to liquid metal cooled systems will be presented. Further, the status of the DRESDYN platform for large-scale experiments with liquid sodium is sketched.

  13. Cloud/Fog Computing System Architecture and Key Technologies for South-North Water Transfer Project Safety

    Directory of Open Access Journals (Sweden)

    Yaoling Fan


    Full Text Available In view of the real-time and distributed features of Internet of Things (IoT safety system in water conservancy engineering, this study proposed a new safety system architecture for water conservancy engineering based on cloud/fog computing and put forward a method of data reliability detection for the false alarm caused by false abnormal data from the bottom sensors. Designed for the South-North Water Transfer Project (SNWTP, the architecture integrated project safety, water quality safety, and human safety. Using IoT devices, fog computing layer was constructed between cloud server and safety detection devices in water conservancy projects. Technologies such as real-time sensing, intelligent processing, and information interconnection were developed. Therefore, accurate forecasting, accurate positioning, and efficient management were implemented as required by safety prevention of the SNWTP, and safety protection of water conservancy projects was effectively improved, and intelligential water conservancy engineering was developed.

  14. How Rembrandt surpassed the Ancients, Italians and Rubens as the Master of ‘the Passions of the Soul'

    Directory of Open Access Journals (Sweden)

    Eric Jan Sluijter


    Full Text Available The passions had to be rendered through the movements of the human figure (Van Mander; however it was an Italian cliché that Netherlandish artists were not able to depict figures properly. This article demonstrates how Rembrandt from his earliest works promoted the image of being the master of the lijdingen des gemoeds. Throughout his career Rembrandt aspired to surpass the artists of antiquity and the Italians through the portrayal of the passions to arouse the strongest possible empathy in the viewer, as Huygens immediately recognised. It is argued that concepts grafted onto classical rhetoric, such as oogenblikkige beweging (a term of his pupil Van Hoogstraten; a violent movement due to a sudden reversal of emotion that involves the viewer forcefully were paramount in his earlier period, and in which one finds parallels with the Senecan-Scaligerian tragedies popular at that time. In contrast, in his later works Rembrandt avoided any movement, realising that the depiction of violent motion undermines the persuasiveness of the still image; he forces the viewer to imagine the inner conflicts in the minds of the protagonists who recognise their fate. To engage the viewer powerfully through a radical ‘from life’ ideology (situating himself in a northern tradition was for Rembrandt a central concern in his continuous competition with the greatest exponents of his art (Titian, Rubens. Hoe Rembrandt schilders uit de Oudheid, de Italianen en Rubens overtrof als meester van de ‘lijdingen des gemoeds’.De passies dienden te worden verbeeld door middel van de bewegingen van de ledematen van de menselijke figuur (Van Mander, maar het was een Italiaanse gemeenplaats dat noorderlingen slecht waren in het schilderen van figuren. In dit artikel wordt gedemonstreerd hoe Rembrandt zich vanaf zijn vroegste werk nadrukkelijk presenteerde als dé meester van de ‘lijdingen des gemoeds’ en gedurende zijn gehele carrière ernaar streefde om door middel

  15. System Coordination of Survivability and Safety of Complex Engineering Objects Operation

    Directory of Open Access Journals (Sweden)

    Nataliya Pankratova


    Full Text Available A system strategy to estimation the guaranteed survivability and safety of complex engineering objects (CEO operation is proposed. The principles that underlie the strategy of the guaranteed safety of CEO operation provide a flexible approach to timely detection, recognition, forecast, and system diagnostics of risk factors and situations, to formulation and implementation of a rational decision in a practicable time within an unremovable time constraint. Implementation of the proposed strategy is shown on example of diagnostics of electromobile-refrigerator functioning in real mode.

  16. Unilever food safety assurance system for refined vegetable oils and fats

    Directory of Open Access Journals (Sweden)

    van Duijn Gerrit


    Full Text Available The Unilever Food Safety Assurance system for refined oils and fats is based on risk assessments for the presence of contaminants or pesticide residues in crude oils, and refining process studies to validate the removal of these components. Crude oil risk assessments were carried out by combining supply chain visits, and analyses of the contaminant and pesticide residue levels in a large number of crude oil samples. Contaminants like poly-aromatic hydrocarbons and hydrocarbons of mineral origin, and pesticide residues can largely be removed by refining. For many years, this Food Safety Assurance System has proven to be effective in controlling contaminant levels in refined vegetable oils and fats.

  17. Idaho National Laboratory Integrated Safety Management System 2010 Effectiveness Review and Declaration Report

    Energy Technology Data Exchange (ETDEWEB)

    Thomas J. Haney


    Idaho National Laboratory completes an annual Integrated Safety Management System effectiveness review per 48 CFR 970.5223-1 “Integration of Environment, Safety and Health into Work Planning and Execution.” The annual review assesses ISMS effectiveness, provides feedback to maintain system integrity, and helps identify target areas for focused improvements and assessments for the following year. Using one of the three Department of Energy (DOE) descriptors in DOE M 450.4-1 regarding the state of ISMS effectiveness during Fiscal Year (FY) 2010, the information presented in this review shows that INL achieved “Effective Performance.”

  18. Integrating incident data from five reporting systems to assess patient safety: making sense of the elephant. (United States)

    Levtzion-Korach, Osnat; Frankel, Allan; Alcalai, Hanna; Keohane, Carol; Orav, John; Graydon-Baker, Erin; Barnes, Janet; Gordon, Kathleen; Puopulo, Anne Louise; Tomov, Elena Ivanova; Sato, Luke; Bates, David W


    A study was conducted to examine and compare information gleaned from five different reporting systems within one institution: incident reporting, patient complaints, risk management, medical malpractice claims, and executive walk rounds. These data sources vary in the timing of the reporting (retrospective or prospective), severity of the events, and profession of the reporters. A common methodology was developed for classifying incidents. Data specific to each incident were abstracted from each system and then categorized using the same framework into one of 23 categories. Overall, there was little overlap, although each reporting system identified important safety issues. Communication problems were common among patient complaints and malpractice claims; malpractice claims' leading category was clinical judgement. Walk rounds identified issues with equipment and supplies. Adverse event reporting systems highlighted identification issues, especially mislabelled specimens. The frequency of contributions of reports by provider group varied substantially by system. Physicians accounted for 50% of risk management reports, but in adverse event reporting, where nurses were the main reporters, physicians accounted for only 2.5% of reports. Complaints and malpractice claims come primarily from patients. The five reporting systems each identified different yet complementary patient safety issues. To obtain a comprehensive picture of their patient safety problems and to develop priorities for improving safety, hospitals should use a broad portfolio of approaches and then synthesize the messages from all individual approaches into a collated and cohesive whole.

  19. Certification Strategies using Run-Time Safety Assurance for Part 23 Autopilot Systems (United States)

    Hook, Loyd R.; Clark, Matthew; Sizoo, David; Skoog, Mark A.; Brady, James


    Part 23 aircraft operation, and in particular general aviation, is relatively unsafe when compared to other common forms of vehicle travel. Currently, there exists technologies that could increase safety statistics for these aircraft; however, the high burden and cost of performing the requisite safety critical certification processes for these systems limits their proliferation. For this reason, many entities, including the Federal Aviation Administration, NASA, and the US Air Force, are considering new options for certification for technologies that will improve aircraft safety. Of particular interest, are low cost autopilot systems for general aviation aircraft, as these systems have the potential to positively and significantly affect safety statistics. This paper proposes new systems and techniques, leveraging run-time verification, for the assurance of general aviation autopilot systems, which would be used to supplement the current certification process and provide a viable path for near-term low-cost implementation. In addition, discussions on preliminary experimentation and building the assurance case for a system, based on these principles, is provided.

  20. Iterative Cellular Screening System for Nanoparticle Safety Testing

    Directory of Open Access Journals (Sweden)

    Franziska Sambale


    Full Text Available Nanoparticles have the potential to exhibit risks to human beings and to the environment; due to the wide applications of nanoproducts, extensive risk management must not be neglected. Therefore, we have constructed a cell-based, iterative screening system to examine a variety of nanoproducts concerning their toxicity during development. The sensitivity and application of various cell-based methods were discussed and proven by applying the screening to two different nanoparticles: zinc oxide and titanium dioxide nanoparticles. They were used as benchmarks to set up our methods and to examine their effects on mammalian cell lines. Different biological processes such as cell viability, gene expression of interleukin-8 and heat shock protein 70, as well as morphology changes were investigated. Within our screening system, both nanoparticle suspensions and coatings can be tested. Electric cell impedance measurements revealed to be a good method for online monitoring of cellular behavior. The implementation of three-dimensional cell culture is essential to better mimic in vivo conditions. In conclusion, our screening system is highly efficient, cost minimizing, and reduces the need for animal studies.

  1. Idaho National Laboratory Integrated Safety Management System FY 2012 Effectiveness Review and Declaration Report

    Energy Technology Data Exchange (ETDEWEB)

    Farren Hunt


    Idaho National Laboratory (INL) performed an Annual Effectiveness Review of the Integrated Safety Management System (ISMS), per 48 Code of Federal Regulations (CFR) 970.5223 1, “Integration of Environment, Safety and Health into Work Planning and Execution.” The annual review assessed Integrated Safety Management (ISM) effectiveness, provided feedback to maintain system integrity, and identified target areas for focused improvements and assessments for fiscal year (FY) 2013. Results of the FY 2012 annual effectiveness review demonstrated that the INL’s ISMS program was significantly strengthened. Actions implemented by the INL demonstrate that the overall Integrated Safety Management System is sound and ensures safe and successful performance of work while protecting workers, the public, and environment. This report also provides several opportunities for improvement that will help further strengthen the ISM Program and the pursuit of safety excellence. Demonstrated leadership and commitment, continued surveillance, and dedicated resources have been instrumental in maturing a sound ISMS program. Based upon interviews with personnel, reviews of assurance activities, and analysis of ISMS process implementation, this effectiveness review concludes that ISM is institutionalized and is “Effective”.

  2. The Parable of the Boiled System Safety Professional: Drift to Failure (United States)

    Shivers, C. Herbert


    Recall from the Parable of the Boiled Frog, that tossing a frog into boiling water causes the frog to jump out and hop away while placing a frog in suitable temperature water and slowly bringing the water to a boil results in the frog boiling due to not being aware of the slowly increasing danger, theoretically, of course. System safety professionals must guard against allowing dangers to creep unnoticed into their projects and be ever alert to notice signs of impending problems. People have used various phrases related to the idea, most notably, latent conditions, James Reason in Managing the Risks of Organizational Accidents (1, pp 10-11), Drift to Failure, Sydney Dekker (2, pp 82-86) in Resilience Engineering: Chronicling the Emergence of Confused Consensus in Resilience Engineering: Concepts and Precepts, Hollnagel, Woods and Leveson, and normalization of deviance, Diane Vaughan in The Challenger Launch Decision: Risky Technology, Culture, and Deviance at NASA (3). Reason also said, If eternal vigilance is the price of liberty, then chronic unease is the price of safety (1, p 37). Our challenge as system safety professionals is to be aware of the emergence of signals that warn us of slowly eroding safety margins. This paper will discuss how system safety professionals might better perform in that regard.

  3. Analysis of Media Agenda-Setting Effects on Consumer Confidence in the Safety of the U.S. Food System


    Bharad, Abhishek Bhagwat; Harrison, R. Wes; Kinsey, Jean D.; Degeneffe, Dennis J.; Ferreira, Gustavo F.C.


    Results from continuous tracking of consumer confidence and media coverage of food safety events over a 67 week period between May 2008 and August 2009 are reported. An ordered probit model is used to test the hypothesis that media coverage of food safety events affects consumer confidence in the safety of the U.S. food system. The results show that media coverage significantly and negatively affected consumer confidence in the safety of nation’s food supply during the sample period. Socioeco...

  4. Health and safety: Preliminary comparative assessment of the Satellite Power System (SPS) and other energy alternatives (United States)

    Habegger, L. J.; Gasper, J. R.; Brown, C.


    Data readily available from the literature were used to make an initial comparison of the health and safety risks of a fission power system with fuel reprocessing; a combined-cycle coal power system with a low-Btu gasifier and open-cycle gas turbine; a central-station, terrestrial, solar photovoltaic power system; the satellite power system; and a first-generation fusion system. The assessment approach consists of the identification of health and safety issues in each phase of the energy cycle from raw material extraction through electrical generation, waste disposal, and system deactivation; quantitative or qualitative evaluation of impact severity; and the rating of each issue with regard to known or potential impact level and level of uncertainty.

  5. Towards the Verification of Safety-critical Autonomous Systems in Dynamic Environments

    Directory of Open Access Journals (Sweden)

    Adina Aniculaesei


    Full Text Available There is an increasing necessity to deploy autonomous systems in highly heterogeneous, dynamic environments, e.g. service robots in hospitals or autonomous cars on highways. Due to the uncertainty in these environments, the verification results obtained with respect to the system and environment models at design-time might not be transferable to the system behavior at run time. For autonomous systems operating in dynamic environments, safety of motion and collision avoidance are critical requirements. With regard to these requirements, Macek et al. [6] define the passive safety property, which requires that no collision can occur while the autonomous system is moving. To verify this property, we adopt a two phase process which combines static verification methods, used at design time, with dynamic ones, used at run time. In the design phase, we exploit UPPAAL to formalize the autonomous system and its environment as timed automata and the safety property as TCTL formula and to verify the correctness of these models with respect to this property. For the runtime phase, we build a monitor to check whether the assumptions made at design time are also correct at run time. If the current system observations of the environment do not correspond to the initial system assumptions, the monitor sends feedback to the system and the system enters a passive safe state.

  6. Water Safety (United States)

    ... School Counselors Kidney Stones Brain and Nervous System Water Safety KidsHealth > For Teens > Water Safety Print A ... tied to alcohol use. previous continue At the Water Park OK, so you do more splashing than ...

  7. An integrated framework for safety, quality and risk management: an information and incident management system based on a universal patient safety classification (United States)

    Runciman, W B; Williamson, J A H; Deakin, A; Benveniste, K A; Bannon, K; Hibbert, P D


    More needs to be done to improve safety and quality and to manage risks in health care. Existing processes are fragmented and there is no single comprehensive source of information about what goes wrong. An integrated framework for the management of safety, quality and risk is needed, with an information and incident management system based on a universal patient safety classification. The World Alliance for Patient Safety provides a platform for the development of a coherent approach; 43 desirable attributes for such an approach are discussed. An example of an incident management and information system serving a patient safety classification is presented, with a brief account of how and where it is currently used. Any such system is valueless unless it improves safety and quality. Quadruple‐loop learning (personal, local, national and international) is proposed with examples of how an exemplar system has been successfully used at the various levels. There is currently an opportunity to “get it right” by international cooperation via the World Health Organization to develop an integrated framework incorporating systems that can accommodate information from all sources, manage and monitor things that go wrong, and allow the worldwide sharing of information and the dissemination of tools for the implementation of strategies which have been shown to work. PMID:17142615

  8. Analysis of the Influence of Construction Insulation Systems on Public Safety in China


    Guowei Zhang; Guoqing Zhu; Guoxiang Zhao


    With the Government of China?s proposed Energy Efficiency Regulations (GB40411-2007), the implementation of external insulation systems will be mandatory in China. The frequent external insulation system fires cause huge numbers of casualties and extensive property damage and have rapidly become a new hot issue in construction evacuation safety in China. This study attempts to reconstruct an actual fire scene and propose a quantitative risk assessment method for upward insulation system fires...

  9. Assessment of patient safety culture in clinical laboratories in the Spanish National Health System. (United States)

    Giménez-Marín, Angeles; Rivas-Ruiz, Francisco; García-Raja, Ana M; Venta-Obaya, Rafael; Fusté-Ventosa, Margarita; Caballé-Martín, Inmaculada; Benítez-Estevez, Alfonso; Quinteiro-García, Ana I; Bedini, José Luis; León-Justel, Antonio; Torra-Puig, Montserrat


    There is increasing awareness of the importance of transforming organisational culture in order to raise safety standards. This paper describes the results obtained from an evaluation of patient safety culture in a sample of clinical laboratories in public hospitals in the Spanish National Health System. A descriptive cross-sectional study was conducted among health workers employed in the clinical laboratories of 27 public hospitals in 2012. The participants were recruited by the heads of service at each of the participating centers. Stratified analyses were performed to assess the mean score, standardized to a base of 100, of the six survey factors, together with the overall patient safety score. 740 completed questionnaires were received (88% of the 840 issued). The highest standardized scores were obtained in Area 1 (individual, social and cultural) with a mean value of 77 (95%CI: 76-78), and the lowest ones, in Area 3 (equipment and resources), with a mean value of 58 (95%CI: 57-59). In all areas, a greater perception of patient safety was reported by the heads of service than by other staff. We present the first multicentre study to evaluate the culture of clinical safety in public hospital laboratories in Spain. The results obtained evidence a culture in which high regard is paid to safety, probably due to the pattern of continuous quality improvement. Nevertheless, much remains to be done, as reflected by the weaknesses detected, which identify areas and strategies for improvement.


    Directory of Open Access Journals (Sweden)

    Alexander Michaylovich Lushkin


    Full Text Available In order to implement the concept of acceptable risk all airlines should have the Safety Management System (SMS from 01.01.2009 - at the request of ICAO and from 01.01.2010 - at the request of the Federal Air Transport Agen- cy. State requirements for SMS have not been formulated clearly. Leading airlines, in an effort to meet international stand- ards, develop and implement SMS on their own. So the implemented SMS differ in control settings (level of safety, proce- dures and methodological support of the processes of safety management. The summary of the best experience in develop- ment, implementation and improvement of SMS in leading airlines, allows to create a standard SMS to the airline, where the basic procedures required by the standards are systematized. The standard SMS is formed on experience in design, implementation and development of corporate SMS in three leading Russian airlines, in which the author worked in 2006-2015, and can be the basis of an SMS of the airlines operat- ing the planes and helicopters. Taken into account in a typical SMS requirements of international and national standards, research results, developed and implemented methodical maintenance of management procedures level of safety, contribut- ed to the successful passage of IATA periodic audits on developing standards of operational safety IOSA by the airline members and achieve the best level of safety not only in Russia but also in the world.

  11. CMIS: Crime Map Information System for Safety Environment (United States)

    Kasim, Shahreen; Hafit, Hanayanti; Yee, Ng Peng; Hashim, Rathiah; Ruslai, Husni; Jahidin, Kamaruzzaman; Syafwan Arshad, Mohammad


    Crime Map is an online web based geographical information system that assists the public and users to visualize crime activities geographically. It acts as a platform for the public communities to share crime activities they encountered. Crime and violence plague the communities we are living in. As part of the community, crime prevention is everyone's responsibility. The purpose of Crime Map is to provide insights of the crimes occurring around Malaysia and raise the public's awareness on crime activities in their neighbourhood. For that, Crime Map visualizes crime activities on a geographical heat maps, generated based on geospatial data. Crime Map analyse data obtained from crime reports to generate useful information on crime trends. At the end of the development, users should be able to make use of the system to access to details of crime reported, crime analysis and report crimes activities. The development of Crime Map also enable the public to obtain insights about crime activities in their area. Thus, enabling the public to work together with the law enforcer to prevent and fight crime.

  12. Cost-Efficient Methods and Processes for Safety Relevant Embedded Systems (CESAR) - An Objective Overview (United States)

    Jolliffe, Graham

    For developing embedded safety critical systems, industrial companies have to face increasing complexity and variety coupled with increasing regulatory constraints, while costs, performances and time to market are constantly challenged. This has led to a profusion of enablers (new processes, methods and tools), which are neither integrated nor interoperable because they have been developed more or less independently (addressing only a part of the complexity: e.g. Safety) in the absence of internationally recognized open standards. CESAR has been established under ARTEMIS, the European Union's Joint Technology Initiative for research in embedded systems, with the aim to improve this situation and this pa-per will explain what CESAR's objectives are, how they are expected to be achieved and, in particular, how current best practice can ensure that safety engineering requirements can be met.

  13. Factors influencing workers to follow food safety management systems in meat plants in Ontario, Canada. (United States)

    Ball, Brita; Wilcock, Anne; Aung, May


    Small and medium sized food businesses have been slow to adopt food safety management systems (FSMSs) such as good manufacturing practices and Hazard Analysis Critical Control Point (HACCP). This study identifies factors influencing workers in their implementation of food safety practices in small and medium meat processing establishments in Ontario, Canada. A qualitative approach was used to explore in-plant factors that influence the implementation of FSMSs. Thirteen in-depth interviews in five meat plants and two focus group interviews were conducted. These generated 219 pages of verbatim transcripts which were analysed using NVivo 7 software. Main themes identified in the data related to production systems, organisational characteristics and employee characteristics. A socio-psychological model based on the theory of planned behaviour is proposed to describe how these themes and underlying sub-themes relate to FSMS implementation. Addressing the various factors that influence production workers is expected to enhance FSMS implementation and increase food safety.

  14. An Examination of Safety Management Systems and Aviation Technologies in the Helicopter Emergency Medical Services Industry (United States)

    Buckner, Steven A.

    The Helicopter Emergency Medical Service (HEMS) industry has a significant role in the transportation of injured patients, but has experienced more accidents than all other segments of the aviation industry combined. With the objective of addressing this discrepancy, this study assesses the effect of safety management systems implementation and aviation technologies utilization on the reduction of HEMS accident rates. Participating were 147 pilots from Federal Aviation Regulations Part 135 HEMS operators, who completed a survey questionnaire based on the Safety Culture and Safety Management System Survey (SCSMSS). The study assessed the predictor value of SMS implementation and aviation technologies to the frequency of HEMS accident rates with correlation and multiple linear regression. The correlation analysis identified three significant positive relationships. HEMS years of experience had a high significant positive relationship with accident rate (r=.90; psafety culture within the HEMS industry.

  15. Idaho National Laboratory Integrated Safety Management System 2011 Effectiveness Review and Declaration Report

    Energy Technology Data Exchange (ETDEWEB)

    Farren Hunt


    Idaho National Laboratory (INL) performed an annual Integrated Safety Management System (ISMS) effectiveness review per 48 Code of Federal Regulations (CFR) 970.5223-1, 'Integration of Environment, Safety and Health into Work Planning and Execution.' The annual review assessed Integrated Safety Management (ISM) effectiveness, provided feedback to maintain system integrity, and helped identify target areas for focused improvements and assessments for fiscal year (FY) 2012. The information presented in this review of FY 2011 shows that the INL has performed many corrective actions and improvement activities, which are starting to show some of the desired results. These corrective actions and improvement activities will continue to help change culture that will lead to better implementation of defined programs, resulting in moving the Laboratory's performance from the categorization of 'Needs Improvement' to the desired results of 'Effective Performance.'

  16. Multi-dimensional database design and implementation of dam safety monitoring system

    Directory of Open Access Journals (Sweden)

    Er-feng ZHAO


    Full Text Available To improve the effectiveness of dam safety monitoring database systems, the development process of a multi-dimensional conceptual data model was analyzed and a logic design was achieved in multi-dimensional database mode. The optimal data model was confirmed by identifying data objects, defining relations and reviewing entities. The conversion of relations among entities to external keys and entities and physical attributes to tables and fields was interpreted completely. On this basis, a multi-dimensional database that reflects the management and analysis of a dam safety monitoring system on monitoring data information has been established, for which factual tables and dimensional tables have been designed. Finally, based on service design and user interface design, the dam safety monitoring system has been developed with Delphi as the development tool. This development project shows that the multi-dimensional database can simplify the development process and minimize hidden dangers in the database structure design. It is superior to other dam safety monitoring system development models and can provide a new research direction for system developers.

  17. The hazard analysis and critical control point system in food safety. (United States)

    Herrera, Anavella Gaitan


    The Hazard Analysis and Critical Control Point (HACCP) system is a preventive method of ensuring food safety. Its objectives are the identification of consumer safety hazards that can occur in the production line and the establishment of a control process to guarantee a safer product for the consumer; it is based on the identification of potential hazards to food safety and on measures aimed at preventing these hazards. HACCP is the system of choice in the management of food safety. The principles of HACCP are applicable to all phases of food production, including basic husbandry practices, food preparation and handling, food processing, food service, distribution systems, and consumer handling and use. The HACCP system is involved in every aspect of food safety production (according to the UN Food and Agriculture Organization [FAO] and the International Commission on Microbiological Specifications for Foods [ICMSF]). The most basic concept underlying the HACCP system is that of prevention rather than inspection. The control of processes and conditions comprises the critical control point (CCP) element. HACCP is simply a methodical, flexible, and systematic application of the appropriate science and technology for planning, controlling, and documenting the safe production of foods. The successful application of HACCP requires the full commitment and involvement of management and the workforce, using a multidisciplinary approach that should include, as appropriate, expertise in agronomy, veterinary health, microbiology, public health, food technology, environmental health, chemistry, engineering, and so on according to the particular situation. Application of the HACCP system is compatible with the implementation of total quality management (TQM) systems such as the ISO 9000 series.

  18. Advances in coupled safety modeling using systems analysis and high-fidelity methods.

    Energy Technology Data Exchange (ETDEWEB)

    Fanning, T. H.; Thomas, J. W.; Nuclear Engineering Division


    The potential for a sodium-cooled fast reactor to survive severe accident initiators with no damage has been demonstrated through whole-plant testing in EBR-II and FFTF. Analysis of the observed natural protective mechanisms suggests that they would be characteristic of a broad range of sodium-cooled fast reactors utilizing metal fuel. However, in order to demonstrate the degree to which new, advanced sodium-cooled fast reactor designs will possess these desired safety features, accurate, high-fidelity, whole-plant dynamics safety simulations will be required. One of the objectives of the advanced safety-modeling component of the Reactor IPSC is to develop a science-based advanced safety simulation capability by utilizing existing safety simulation tools coupled with emerging high-fidelity modeling capabilities in a multi-resolution approach. As part of this integration, an existing whole-plant systems analysis code has been coupled with a high-fidelity computational fluid dynamics code to assess the impact of high-fidelity simulations on safety-related performance. With the coupled capabilities, it is possible to identify critical safety-related phenomenon in advanced reactor designs that cannot be resolved with existing tools. In this report, the impact of coupling is demonstrated by evaluating the conditions of outlet plenum thermal stratification during a protected loss of flow transient. Outlet plenum stratification was anticipated to alter core temperatures and flows predicted during natural circulation conditions. This effect was observed during the simulations. What was not anticipated, however, is the far-reaching impact that resolving thermal stratification has on the whole plant. The high temperatures predicted at the IHX inlet due to thermal stratification in the outlet plenum forces heat into the intermediate system to the point that it eventually becomes a source of heat for the primary system. The results also suggest that flow stagnation in the

  19. Automatic Verification of Timing Constraints for Safety Critical Space Systems (United States)

    Fernandez, Javier; Parra, Pablo; Sanchez Prieto, Sebastian; Polo, Oscar; Bernat, Guillem


    In this paper is presented an automatic process of verification. We focus in the verification of scheduling analysis parameter. This proposal is part of process based on Model Driven Engineering to automate a Verification and Validation process of the software on board of satellites. This process is implemented in a software control unit of the energy particle detector which is payload of Solar Orbiter mission. From the design model is generated a scheduling analysis model and its verification model. The verification as defined as constraints in way of Finite Timed Automatas. When the system is deployed on target the verification evidence is extracted as instrumented points. The constraints are fed with the evidence, if any of the constraints is not satisfied for the on target evidence the scheduling analysis is not valid.

  20. New Techniques for Improved Safety in Complex Systems

    DEFF Research Database (Denmark)

    Rasmussen, Jens


    During the latest decade analyses of accidents invariably have pointed to the role of human error and it is often stated that 80-90 % of all accidents are caused by human error. Consequently, considerable resources have been spent on human error research. The concept of human error is,however, very...... elusive. At a closer look, the frequent allocation of accidental causes to human error appears to rather subjective. This is a simple reflection of the nature of causal analysis. The lecture will present a discussion of the cognitive aspects of errors and the close relationship with human learning...... and adaptation are discussed. Errors are the reflection of normally very effective cognitive mechanisms in a particular context. Based on this position, some directions for design of error tolerant systems will be presented....

  1. Safety of Systemic Agents for the Treatment of Pediatric Psoriasis

    DEFF Research Database (Denmark)

    Bronckers, Inge M G J; Seyger, Marieke M B; West, Dennis P


    , the mean interval between diagnosis and starting systemic therapy was 3.0 years. Methotrexate was used by 270 patients (69.2%), biologic agents (primarily etanercept) by 106 (27.2%), acitretin by 57 (14.6%), cyclosporine by 30 (7.7%), fumaric acid esters by 19 (4.9%), and more than 1 medication was used...... against gastrointestinal AEs more than once-weekly folic acid, regardless of the total weekly dosage. Methotrexate-associated hepatic transaminase elevations were associated with obesity (35 of 270 patients [13.0%]), but a folic acid regimen was not. Injection site reactions occurred in 20 of 106 patients...... inhibitors, but having 1 or more infections related to medication (predominantly upper airway) was less likely. Six patients developed a serious treatment-related AE (methotrexate, 3; fumaric acid esters, 2; and adalimumab, 1), but methotrexate and biologic agents were taken for a mean duration that was 2...

  2. Safety leadership and systems thinking: application and evaluation of a Risk Management Framework in the mining industry. (United States)

    Donovan, Sarah-Louise; Salmon, Paul M; Lenné, Michael G; Horberry, Tim


    Safety leadership is an important factor in supporting safety in high-risk industries. This article contends that applying systems-thinking methods to examine safety leadership can support improved learning from incidents. A case study analysis was undertaken of a large-scale mining landslide incident in which no injuries or fatalities were incurred. A multi-method approach was adopted, in which the Critical Decision Method, Rasmussen's Risk Management Framework and Accimap method were applied to examine the safety leadership decisions and actions which enabled the safe outcome. The approach enabled Rasmussen's predictions regarding safety and performance to be examined in the safety leadership context, with findings demonstrating the distribution of safety leadership across leader and system levels, and the presence of vertical integration as key to supporting the successful safety outcome. In doing so, the findings also demonstrate the usefulness of applying systems-thinking methods to examine and learn from incidents in terms of what 'went right'. The implications, including future research directions, are discussed. Practitioner Summary: This paper presents a case study analysis, in which systems-thinking methods are applied to the examination of safety leadership decisions and actions during a large-scale mining landslide incident. The findings establish safety leadership as a systems phenomenon, and furthermore, demonstrate the usefulness of applying systems-thinking methods to learn from incidents in terms of what 'went right'. Implications, including future research directions, are discussed.

  3. Modelling of Disturbing Efects within Communication Channel for Safety-Related Communication System

    Directory of Open Access Journals (Sweden)

    Maria Franekova


    Full Text Available The aim of the paper is using of modelling within development of safety–related communication systems presented in the areas where guaranty of safety integrity level is required. In the paper basic principles used in the process of safety evaluation in closed transmission systems are summarised. Dangerous states of system are mainly caused by random failures of HW within non-trusted transmission system, by electromagnetic interference caused with noise or interferences and by systematic failures within specification of system. Main part of paper describes the simulation of disturbing effects within communication channel via programme Matlab, relations for determination of probability of undetected errors of code words with using block codes and results of residual error rate for Hamming code.

  4. Application of Petri nets to reliability prediction of occupant safety systems with partial detection and repair

    Energy Technology Data Exchange (ETDEWEB)

    Kleyner, Andre, E-mail: [Delphi Corporation, Electronics and Safety Division, P.O. Box 9005, M.S. CTC 2E, Kokomo, IN 46904 (United States); Volovoi, Vitali, E-mail: vitali.volovoi@ae.gatech.ed [School of Aerospace Engineering, Georgia Institute of Technology, Atlanta, GA 30332 (United States)


    This paper presents an application of stochastic Petri nets (SPN) to calculate the availability of safety critical on-demand systems. Traditional methods of estimating system reliability include standards-based or field return-based reliability prediction methods. These methods do not take into account the effect of fault-detection capability and penalize the addition of detection circuitry due to the higher parts count. Therefore, calculating system availability, which can be linked to the system's probability of failure on demand (P{sub fd}), can be a better alternative to reliability prediction. The process of estimating the P{sub fd} of a safety system can be further complicated by the presence of system imperfections such as partial-fault detection by users and untimely or uncompleted repairs. Additionally, most system failures cannot be represented by Poisson process Markov chain methods, which are commonly utilized for the purposes of estimating P{sub fd}, as these methods are not well-suited for the analysis of non-Poisson failures. This paper suggests a methodology and presents a case study of SPN modeling adequately handling most of the above problems. The model will be illustrated with a case study of an automotive electronics airbag controller as an example of a safety critical on-demand system.

  5. Are automatic systems the future of motorcycle safety? A novel methodology to prioritize potential safety solutions based on their projected effectiveness. (United States)

    Gil, Gustavo; Savino, Giovanni; Piantini, Simone; Baldanzini, Niccolò; Happee, Riender; Pierini, Marco


    Motorcycle riders are involved in significantly more crashes per kilometer driven than passenger car drivers. Nonetheless, the development and implementation of motorcycle safety systems lags far behind that of passenger cars. This research addresses the identification of the most effective motorcycle safety solutions in the context of different countries. A knowledge-based system of motorcycle safety (KBMS) was developed to assess the potential for various safety solutions to mitigate or avoid motorcycle crashes. First, a set of 26 common crash scenarios was identified from the analysis of multiple crash databases. Second, the relative effectiveness of 10 safety solutions was assessed for the 26 crash scenarios by a panel of experts. Third, relevant information about crashes was used to weigh the importance of each crash scenario in the region studied. The KBMS method was applied with an Italian database, with a total of more than 1 million motorcycle crashes in the period 2000-2012. When applied to the Italian context, the KBMS suggested that automatic systems designed to compensate for riders' or drivers' errors of commission or omission are the potentially most effective safety solution. The KBMS method showed an effective way to compare the potential of various safety solutions, through a scored list with the expected effectiveness of each safety solution for the region to which the crash data belong. A comparison of our results with a previous study that attempted a systematic prioritization of safety systems for motorcycles (PISa project) showed an encouraging agreement. Current results revealed that automatic systems have the greatest potential to improve motorcycle safety. Accumulating and encoding expertise in crash analysis from a range of disciplines into a scalable and reusable analytical tool, as proposed with the use of KBMS, has the potential to guide research and development of effective safety systems. As the expert assessment of the crash

  6. Intensity of EMF generated by electronic safety system devices

    Directory of Open Access Journals (Sweden)

    Pospisilik Martin


    Full Text Available As the importance of wireless networks based on radio frequencies increases in time, a space for discussion on harmfulness of the electromagnetic radiation has occurred. On the one hand there are studies showing that a direct influence of non-ionizing electromagnetic waves on the human organism was not confirmed until a certain intensity has been reached. On the other hand, critical voices appear, warning that even low intensities of non-ionizing electromagnetic fields are harmful to the human body, if it is exposed to the radiation for a prolonged time. The authors of this paper have no ambition to resolve this dispute. However, they provide data on the intensity of the electromagnetic fields generated by several components of electronic security system that are operating on the basis of the wireless network. The data have been gained in a specialized workplace and will allow the reader to imagine how intensive the radio signals generated by the battery-operated devices are compared to the current hygienic and technical limits.

  7. An Intelligent Monitoring System for the Safety of Building Structure under the W2T Framework

    NARCIS (Netherlands)

    Wang, H.; Huang, Z.; Zhong, N.; Han, Y.; Zhang, F.


    Monitoring systems for the safety of building structure (SBS) can provide people with important data related to main supporting points in a building and then help people to make a reasonable maintenance schedule. However, more and more data bring a challenge for data management and data mining. In

  8. Co-existence of TV broadcast and wireless systems for public safety ...

    African Journals Online (AJOL)

    The spectrum sharing between primary TV systems (Channels 9 and 35) and Public Safety Networks (PSNs) is presented in this article. The networks to be deployed within Television White Space (TVWS) in Ilorin metropolis of Kwara State operate on a secondary basis spatially, without causing harmful interference to ...

  9. Architecture-led Requirements and Safety Analysis of an Aircraft Survivability Situational Awareness System (United States)


    of safety hazards through a fault propagation ontology and This material is based upon...Administration (FAA) Requirements Engineering Management Handbook (Ref. 3). ALRS adapts the CPRET (Ref.4) representation of a system defined by the...release. Distribution unlimited. 3 annotates an AADL model with fault information utilizing an error propagation ontology as illustrated graphically

  10. Wind Turbine Generator System Safety and Function Test Report for the Ventera VT10 Wind Turbine

    Energy Technology Data Exchange (ETDEWEB)

    Smith, J.; Huskey, A.; Jager, D.; Hur, J.


    This report summarizes the results of a safety and function test that NREL conducted on the Ventera VT10 wind turbine. This test was conducted in accordance with the International Electrotechnical Commissions' (IEC) standard, Wind Turbine Generator System Part 2: Design requirements for small wind turbines, IEC 61400-2 Ed.2.0, 2006-03.

  11. Wind Turbine Generator System Safety and Function Test Report for the Entegrity EW50 Wind Turbine

    Energy Technology Data Exchange (ETDEWEB)

    Smith, J.; Huskey, A.; Jager, D.; Hur, J.


    This report summarizes the results of a safety and function test that NREL conducted on the Entegrity EW50 wind turbine. This test was conducted in accordance with the International Electrotechnical Commissions' (IEC) standard, Wind Turbine Generator System Part 2: Design requirements for small wind turbines, IEC 61400-2 Ed.2.0, 2006-03.

  12. Towards Future Broadband Public Safety Systems: Current Issues and Future Directions

    DEFF Research Database (Denmark)

    Popovska Avramova, Andrijana; Ruepp, Sarah Renée; Dittmann, Lars


    The vision of the Fifth generation (5G) of mobile communication is that it will be an umbrella for communications for various vertical industries that have different requirements for delay, data rates, reliability, availability, and security. 5G will not be a single technology - rather a converge...... broadband trusted communication system for safety and critical missions...

  13. 78 FR 47014 - Configuration Management Plans for Digital Computer Software Used in Safety Systems of Nuclear... (United States)


    ... (IEEE) Standard 828-2005, ``IEEE Standard for Software Configuration Management Plans,'' issued in 2005... RG 1.169 endorses IEEE Std. 828-2005, ``IEEE Standard for Software Configuration Management Plans... COMMISSION Configuration Management Plans for Digital Computer Software Used in Safety Systems of Nuclear...

  14. Development of crash imminent test scenarios for Integrated Vehicle-Based Safety Systems (United States)


    This report identifies crash imminent test scenarios based on common pre-crash scenarios for integrated vehicle-based safety systems that alert the driver of a light vehicle or a heavy truck to an impending rear-end, lane change, or run-off-road cras...

  15. The traffic safety of the Carin car information and navigation system : Summary report

    NARCIS (Netherlands)

    Blikman, G.


    Report of the Delft University of Technology, Department of Transportation Planning and Highway Engineering in assignment of Philips International B.V. The Carin Car Information and Navigation system has been analysed on its possible positive and negative effects on traffic safety. Requirements have

  16. Development of a GIS-based monitoring and management system for underground coal mining safety

    Energy Technology Data Exchange (ETDEWEB)

    Salap, Seda; Karslioglu, Mahmut Onur [Civil Engineering Department, Geomatics Division, Middle East Technical University, Ankara (Turkey); Demirel, Nuray [Mining Engineering Department, Middle East Technical University, Ankara (Turkey)


    Coal mine safety is of paramount concern to mining industry. Mine accidents have various causes and consequences including catastrophic failure of mine, substantial economic losses and most notably loss of lives. Therefore, any initiative in mine monitoring is of vital importance for progressing safety surveillance and maintenance. This paper presents the development of a geographic information system (GIS)-based monitoring and management system for underground mine safety in three levels as constructive safety, surveillance and maintenance, and emergency. The developed model integrates the database design and management to the monitoring system implementation which encompasses query and analysis operations with the help of web and desktop applications. Interactive object-oriented graphical user interfaces (GUIs) were developed to visualize information about the entities gathered from the model and also to provide analysis operations based on the graphical representations and demonstrations using data tables and map objects. The research methodology essentially encompasses five main stages: (i) designing a conceptual database model; (ii) development of a logical model in terms of entity-relationship (ER) diagrams; (iii) development of a physical model based on physical constraints and requirements; (iv) development of GUIs and implementation of the developed model, analysis and queries; (v) verification and validation of the created model for Oemerler underground coal mine in Turkey. The proposed system is expected to be an efficient tool for improving and maintaining healthy standards in underground coal mines which can possibly be extended to a national GIS infrastructure. (author)

  17. Next Generation Nuclear Plant Structures, Systems, and Components Safety Classification White Paper

    Energy Technology Data Exchange (ETDEWEB)

    Pete Jordan


    This white paper outlines the relevant regulatory policy and guidance for a risk-informed approach for establishing the safety classification of Structures, Systems, and Components (SSCs) for the Next Generation Nuclear Plant and sets forth certain facts for review and discussion in order facilitate an effective submittal leading to an NGNP Combined Operating License application under 10 CFR 52.

  18. A Formal Application of Safety and Risk Assessment in Software Systems (United States)


    Analysis (FTA), Petri Nets, Failure Modes Effect and Criticality Analysis (FMECA), HAZOP , Impact Analysis, and Cigital’s Safety Net Methodology based on...Government Off The Shelf GUI Graphical User Interface (H) Hazardous Event HAZOP Hazardous Operation 318 I The set of all Inputs in the System IAM

  19. Artificial neural networks and neuro-fuzzy inference systems as virtual sensors for hydrogen safety prediction

    Energy Technology Data Exchange (ETDEWEB)

    Karri, Vishy; Ho, Tien [School of Engineering, University of Tasmania, GPO Box 252-65, Hobart, Tasmania 7001 (Australia); Madsen, Ole [Department of Production, Aalborg University, Fibigerstraede 16, DK-9220 Aalborg (Denmark)


    Hydrogen is increasingly investigated as an alternative fuel to petroleum products in running internal combustion engines and as powering remote area power systems using generators. The safety issues related to hydrogen gas are further exasperated by expensive instrumentation required to measure the percentage of explosive limits, flow rates and production pressure. This paper investigates the use of model based virtual sensors (rather than expensive physical sensors) in connection with hydrogen production with a Hogen 20 electrolyzer system. The virtual sensors are used to predict relevant hydrogen safety parameters, such as the percentage of lower explosive limit, hydrogen pressure and hydrogen flow rate as a function of different input conditions of power supplied (voltage and current), the feed of de-ionized water and Hogen 20 electrolyzer system parameters. The virtual sensors are developed by means of the application of various Artificial Intelligent techniques. To train and appraise the neural network models as virtual sensors, the Hogen 20 electrolyzer is instrumented with necessary sensors to gather experimental data which together with MATLAB neural networks toolbox and tailor made adaptive neuro-fuzzy inference systems (ANFIS) were used as predictive tools to estimate hydrogen safety parameters. It was shown that using the neural networks hydrogen safety parameters were predicted to less than 3% of percentage average root mean square error. The most accurate prediction was achieved by using ANFIS. (author)

  20. 30 CFR 250.1630 - Safety-system testing and records. (United States)


    ... Section 250.1630 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL.... Testing must be in accordance with API RP 14C, Appendix D (incorporated by reference as specified in § 250.198). For safety system devices other than those listed in API RP 14C, Appendix D, you must utilize...