WE-F-209-02: Radiation Safety Surveys of Linear Accelerators

International Nuclear Information System (INIS)

Martin, M.

2016-01-01

Over the past few years, numerous Accreditation Bodies, Regulatory Agencies, and State Regulations have implemented requirements for Radiation Safety Surveys following installation or modification to x-ray rooms. The objective of this session is to review best practices in performing radiation safety surveys for both Therapy and Diagnostic installations, as well as a review of appropriate survey instruments. This session will be appropriate for both therapy and imaging physicists who are looking to increase their working knowledge of radiation safety surveys. Learning Objectives: Identify Appropriate Survey Meters for Radiation Safety Surveys Develop best practices for Radiation Safety Surveys for Therapy units that include common areas of concern. Develop best practices for Radiation Safety Surveys of Diagnostic and Nuclear Medicine rooms. Identify acceptable dose levels and the factors that affect the calculations associated with performing Radiation Safety Surveys.

Pharmacist medication reviews to improve safety monitoring in primary care patients.

Science.gov (United States)

Gallimore, Casey E; Sokhal, Dimmy; Zeidler Schreiter, Elizabeth; Margolis, Amanda R

2016-06-01

Patients prescribed psychotropic medications within primary care are at risk of suboptimal monitoring. It is unknown whether pharmacists can improve medication safety through targeted monitoring of at risk populations. Access Community Health Centers implemented a quality improvement pilot project that included pharmacists on an integrated care team to provide medication reviews for patients. Aims were to determine whether inclusion of a pharmacist performing medication reviews within a primary care behavioral health (PCBH) practice is feasible and facilitates safe medication use. Pharmacists performed medication reviews of the electronic health record for patients referred for psychiatry consultation. Reviews were performed 1-3 months following consultation and focused on medications with known suboptimal monitoring rates. Reviews were documented within the EHR and routed to the primary care provider. Primary outcome measures were change in percentage up-to-date on monitoring and AIMS assessment, and at risk of experiencing drug interaction(s) between baseline and 3 months postreview. Secondary outcome was provider opinion of medication reviews collected via electronic survey. Reviews were performed for 144 patients. Three months postreview, percentage up-to-date on recommended monitoring increased 18% (p = .0001), at risk for drug interaction decreased 20% (p improved safety monitoring of psychotropic medications. Results identify key areas for improvement that other clinics considering integration of similar pharmacy services should consider. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Safety climate in Swiss hospital units: Swiss version of the Safety Climate Survey

Science.gov (United States)

Gehring, Katrin; Mascherek, Anna C.; Bezzola, Paula

2015-01-01

Abstract Rationale, aims and objectives Safety climate measurements are a broadly used element of improvement initiatives. In order to provide a sound and easy‐to‐administer instrument for the use in Swiss hospitals, we translated the Safety Climate Survey into German and French. Methods After translating the Safety Climate Survey into French and German, a cross‐sectional survey study was conducted with health care professionals (HCPs) in operating room (OR) teams and on OR‐related wards in 10 Swiss hospitals. Validity of the instrument was examined by means of Cronbach's alpha and missing rates of the single items. Item‐descriptive statistics group differences and percentage of ‘problematic responses’ (PPR) were calculated. Results 3153 HCPs completed the survey (response rate: 63.4%). 1308 individuals were excluded from the analyses because of a profession other than doctor or nurse or invalid answers (n = 1845; nurses = 1321, doctors = 523). Internal consistency of the translated Safety Climate Survey was good (Cronbach's alpha G erman = 0.86; Cronbach's alpha F rench = 0.84). Missing rates at item level were rather low (0.23–4.3%). We found significant group differences in safety climate values regarding profession, managerial function, work area and time spent in direct patient care. At item level, 14 out of 21 items showed a PPR higher than 10%. Conclusions Results indicate that the French and German translations of the Safety Climate Survey might be a useful measurement instrument for safety climate in Swiss hospital units. Analyses at item level allow for differentiating facets of safety climate into more positive and critical safety climate aspects. PMID:25656302

The arrangement of deformation monitoring project and analysis of monitoring data of a hydropower engineering safety monitoring system

Science.gov (United States)

Wang, Wanshun; Chen, Zhuo; Li, Xiuwen

2018-03-01

The safety monitoring is very important in the operation and management of water resources and hydropower projects. It is the important means to understand the dam running status, to ensure the dam safety, to safeguard people’s life and property security, and to make full use of engineering benefits. This paper introduces the arrangement of engineering safety monitoring system based on the example of a water resource control project. The monitoring results of each monitoring project are analyzed intensively to show the operating status of the monitoring system and to provide useful reference for similar projects.

Monitoring circuit for reactor safety systems

Science.gov (United States)

Keefe, Donald J.

1976-01-01

The ratio between the output signals of a pair of reactor safety channels is monitored. When ratio falls outside of a predetermined range, it indicates that one or more of the safety channels has malfunctioned.

Radiation safety considerations and compliance within equine veterinary clinics: Results of an Australian survey

International Nuclear Information System (INIS)

Surjan, Y.; Ostwald, P.; Milross, C.; Warren-Forward, H.

2015-01-01

Objective: To examine current knowledge and the level of compliance of radiation safety principles in equine veterinary clinics within Australia. Method: Surveys were sent to equine veterinary surgeons working in Australia. The survey was delivered both online and in hardcopy format; it comprised 49 questions, 15 of these directly related to radiation safety. The participants were asked about their current and previous use of radiation-producing equipment. Information regarding their level of knowledge and application of radiation safety principles and practice standards was collected and analysed. Results: The use of radiation-producing equipment was evident in 94% of responding clinics (a combination of X-ray, CT and/or Nuclear Medicine Cameras). Of those with radiation-producing equipment, 94% indicated that they hold a radiation licence, 78% had never completed a certified radiation safety course and 19% of participants did not use a personal radiation monitor. In 14% of cases, radiation safety manuals or protocols were not available within clinics. Conclusions: The study has shown that knowledge and application of guidelines as provided by the Code of Practice for Radiation Protection in Veterinary Medicine (2009) is poorly adhered to. The importance of compliance with regulatory requirements is pivotal in minimising occupational exposure to ionising radiation in veterinary medicine, thus there is a need for increased education and training in the area. - Highlights: • Application of the Code of Practice for Veterinary Medicine is poorly adhered to. • Majority of veterinary clinics had not completed certified radiation safety course. • One-fifth of participants did not use personal radiation monitoring. • Increased education and training in area of radiation safety and protection required to generate compliance in clinics

Monitoring circuit for reactor safety systems

International Nuclear Information System (INIS)

Keefe, D.J.

1976-01-01

The ratio between the output signals of a pair of reactor safety channels is monitored. When ratio falls outside of a predetermined range, it indicates that one or more of the safety channels has malfunctioned. 3 claims, 2 figures

Safety Culture Survey in Krsko NPP

International Nuclear Information System (INIS)

Strucic, M.; Bilic Zadric, T.

2008-01-01

The high level of nuclear safety, stability and competitiveness of electricity production, and public acceptability are the main objectives of Krsko Nuclear Power Plant. This is achievable only in environment where strong Safety Culture is taking dominant place in the way how employees communicate, perform tasks, share their ideas and attitudes, and demonstrate their concern in all aspects of work and coexistence. To achieve these objectives, behaviour of all employees as well as specific ethical values must become more transparent and that must arise from the heart of organization. Continuous ongoing and periodic self assessments of Safety Culture in Krsko NPP present major tools in implementation process of this approach. Benefits from Periodic interdisciplinary focused self assessment approach, which main intention is finding the strengths and potential areas for improvements, was used second time to assess the area of Safety Culture in Krsko NPP. Main objectives of self assessment, performed in 2006, were to increase the awareness of the present culture, to serve as a basis for improvement and to keep track of the effects of change or improvement over a longer period of time. For the purpose of effective self assessment, extensive questionnaire was used to obtain information that is representative for whole organization. Wide range of questions was chosen to cover five major characteristics of safety culture: Accountability for safety is clear, Safety is integrated into all activities, Safety culture is learning-driven, Leadership for safety is clear and Safety is a clearly recognized value. 484 Krsko NPP employees and 96 contractors were participated in survey. 70-question survey provided information that was quantified and results compared between groups. Anonymity of participant, as well as their willingness to contribute in this assessment implicates the high level of their openness in answering the questions. High number of participant made analysis of

The Safety Pharmacology Society salary survey.

Science.gov (United States)

Pugsley, Michael K; Authier, Simon; Brabham, Tiffini; Soloviev, Maxim; Markgraf, Carrie G; Correll, Krystle; Traebert, Martin; Greiter-Wilke, Andrea; Valentin, Jean-Pierre; Vargas, Hugo; Botchway, Alfred; Leishman, Derek J; Curtis, Michael J

2017-11-01

Safety pharmacology is a growing discipline with scientists broadly distributed across international geographical regions. This electronic salary survey is the first to be distributed amongst the entire Safety Pharmacology Society (SPS) membership. An electronic survey was sent to all members of the Society. Categorical survey questions assessed membership employment types, annual incomes, and professional certifications, along with other associated career attributes. This survey was distributed to the SPS membership that is comprised of safety pharmacologists, toxicologists and pharmacologists working globally in the pharmaceutical industry, at contract research organizations (CRO), regulatory agencies, and academia or within the technology provider industry. The survey was open for responses from December 2015 to March 2016. The survey response rate was 28% (129/453). North America (68%) was the region with the largest number of respondents followed by Europe (28%). A preponderance of respondents (77%) had 12years of industry experience or more. 52% of responders earned annually between $40,000 and $120,000. As expected, salary was generally positively correlated with the number of years of experience in the industry or the educational background but there was no correlation between salary and the number of employee's directly supervised. The median salary was higher for male vs female respondents, but so was median age, indicative of no gender 'salary gap'. Our 2016 SPS salary survey results showcased significant diversity regarding factors that can influence salary compensation within this discipline. These data provided insights into the complex global job market trends. They also revealed the level of scientific specialization embedded within the organization, presently uniquely positioned to support the dynamic career paths of current and future safety pharmacologists. Copyright © 2017 Elsevier Inc. All rights reserved.

Tuning permissiveness of active safety monitors for autonomous systems

OpenAIRE

Masson , Lola; Guiochet , Jérémie; Waeselynck , Hélène; Cabrera , Kalou; Cassel , Sofia; Törngren , Martin

2018-01-01

International audience; Robots and autonomous systems have become a part of our everyday life, therefore guaranteeing their safety is crucial.Among the possible ways to do so, monitoring is widely used, but few methods exist to systematically generate safety rules to implement such monitors. Particularly, building safety monitors that do not constrain excessively the system's ability to perform its tasks is necessary as those systems operate with few human interventions.We propose in this pap...

Risk monitor - a tool for operational safety assessment risk monitor - user's manual

International Nuclear Information System (INIS)

Hari Prasad, M.; Vinod, Gopika; Saraf, R.K.; Ghosh, A.K.

2006-06-01

Probabilistic Safety Assessment has become a key tool as on today to identify and understand Nuclear Power Plant vulnerabilities. As a result of the availability of these PSA studies, there is a desire to use them to enhance plant safety and to operate the nuclear stations in the most efficient manner. Risk Monitor is a PC based tool, which computes the real time safety level and assists plant personnel to manage day-to-day activities. Risk Monitor is a PC based user friendly software tool used for modification and re-analysis of a nuclear Power plant. Operation of Risk Monitor is based on PSA methods for assisting in day to day applications. Risk Monitoring programs can assess the risk profile and are used to optimize the operation of Nuclear Power Plants with respect to a minimum risk level over the operating time. This report presents the background activities of Risk Monitor, its application areas and the step by step procedure for the user.to interact with the software. This software can be used with the PSA model of any Nuclear Power Plant. (author)

Quality and Safety of Home ICP Monitoring Compared with In-Hospital Monitoring

DEFF Research Database (Denmark)

Andresen, Morten; Juhler, Marianne; Munch, Tina Nørgaard

2012-01-01

Introduction: Intracranial pressure (ICP) monitoring is usually conducted in-hospital using stationary devices. Modern mobile ICP monitoring systems present new monitoring possibilities more closely following the patients' daily life. We reviewed patient safety, quality of technical data...

Internet Safety and Security Surveys - A Review

DEFF Research Database (Denmark)

Sharp, Robin

This report gives a review of investigations into Internet safety and security over the last 10 years. The review covers a number of surveys of Internet usage, of Internet security in general, and of Internet users' awareness of issues related to safety and security. The focus and approach...... of the various surveys is considered, and is related to more general proposals for investigating the issues involved. A variety of proposals for how to improve levels of Internet safety and security are also described, and they are reviewed in the light of studies of motivational factors which affect the degree...

Intelligent monitoring-based safety system of massage robot

Institute of Scientific and Technical Information of China (English)

胡宁; 李长胜; 王利峰; 胡磊; 徐晓军; 邹雲鹏; 胡玥; 沈晨

2016-01-01

As an important attribute of robots, safety is involved in each link of the full life cycle of robots, including the design, manufacturing, operation and maintenance. The present study on robot safety is a systematic project. Traditionally, robot safety is defined as follows: robots should not collide with humans, or robots should not harm humans when they collide. Based on this definition of robot safety, researchers have proposed ex ante and ex post safety standards and safety strategies and used the risk index and risk level as the evaluation indexes for safety methods. A massage robot realizes its massage therapy function through applying a rhythmic force on the massage object. Therefore, the traditional definition of safety, safety strategies, and safety realization methods cannot satisfy the function and safety requirements of massage robots. Based on the descriptions of the environment of massage robots and the tasks of massage robots, the present study analyzes the safety requirements of massage robots; analyzes the potential safety dangers of massage robots using the fault tree tool; proposes an error monitoring-based intelligent safety system for massage robots through monitoring and evaluating potential safety danger states, as well as decision making based on potential safety danger states; and verifies the feasibility of the intelligent safety system through an experiment.

Jaguar surveying and monitoring in the United States

Science.gov (United States)

Culver, Melanie

2016-06-10

Because of the jaguar’s (Panthera onca) endangered status under the Endangered Species Act (ESA) of 1973 throughout its range (from Arizona in the north to Argentina in the south), jaguar individuals and populations are monitored to varying degrees throughout their range. Knowledge gained from monitoring jaguars is helpful for wildlife managers who are responsible for conserving this species. The University of Arizona (UA) has conducted a multiyear surveying and monitoring effort for jaguars and ocelots in southern Arizona and New Mexico. The purpose of this work was to establish an effective surveying and monitoring system for jaguars along the United States-Mexico border. Surveying and monitoring in this study focused on the United States side of the border, but the methods could also be used in Mexico. The intent was to develop and implement a surveying and monitoring system that would provide the greatest probability of recording jaguar presence in, and passage through, the border area.

Risk-based reconfiguration of safety monitoring system using dynamic Bayesian network

International Nuclear Information System (INIS)

Kohda, Takehisa; Cui Weimin

2007-01-01

To prevent an abnormal event from leading to an accident, the role of its safety monitoring system is very important. The safety monitoring system detects symptoms of an abnormal event to mitigate its effect at its early stage. As the operation time passes by, the sensor reliability decreases, which implies that the decision criteria of the safety monitoring system should be modified depending on the sensor reliability as well as the system reliability. This paper presents a framework for the decision criteria (or diagnosis logic) of the safety monitoring system. The logic can be dynamically modified based on sensor output data monitored at regular intervals to minimize the expected loss caused by two types of safety monitoring system failure events: failed-dangerous (FD) and failed-safe (FS). The former corresponds to no response under an abnormal system condition, while the latter implies a spurious activation under a normal system condition. Dynamic Bayesian network theory can be applied to modeling the entire system behavior composed of the system and its safety monitoring system. Using the estimated state probabilities, the optimal decision criterion is given to obtain the optimal diagnosis logic. An illustrative example of a three-sensor system shows the merits and characteristics of the proposed method, where the reasonable interpretation of sensor data can be obtained

Assessing medical students' perceptions of patient safety: the medical student safety attitudes and professionalism survey.

Science.gov (United States)

Liao, Joshua M; Etchegaray, Jason M; Williams, S Tyler; Berger, David H; Bell, Sigall K; Thomas, Eric J

2014-02-01

To develop and test the psychometric properties of a survey to measure students' perceptions about patient safety as observed on clinical rotations. In 2012, the authors surveyed 367 graduating fourth-year medical students at three U.S. MD-granting medical schools. They assessed the survey's reliability and construct and concurrent validity. They examined correlations between students' perceptions of organizational cultural factors, organizational patient safety measures, and students' intended safety behaviors. They also calculated percent positive scores for cultural factors. Two hundred twenty-eight students (62%) responded. Analyses identified five cultural factors (teamwork culture, safety culture, error disclosure culture, experiences with professionalism, and comfort expressing professional concerns) that had construct validity, concurrent validity, and good reliability (Cronbach alphas > 0.70). Across schools, percent positive scores for safety culture ranged from 28% (95% confidence interval [CI], 13%-43%) to 64% (30%-98%), while those for teamwork culture ranged from 47% (32%-62%) to 74% (66%-81%). They were low for error disclosure culture (range: 10% [0%-20%] to 27% [20%-35%]), experiences with professionalism (range: 7% [0%-15%] to 23% [16%-30%]), and comfort expressing professional concerns (range: 17% [5%-29%] to 38% [8%-69%]). Each cultural factor correlated positively with perceptions of overall patient safety as observed in clinical rotations (r = 0.37-0.69, P safety behavioral intent item. This study provided initial evidence for the survey's reliability and validity and illustrated its applicability for determining whether students' clinical experiences exemplify positive patient safety environments.

Monitoring and reviewing research reactor safety in Australia

International Nuclear Information System (INIS)

Cairns, R.C.; Greenslade, G.K.

1990-01-01

Th research reactors operated by the Australian Nuclear Science and Technology Organization (ANSTO) comprise the 10 MW reactor HIFAR and the 100 kW reactor Moata. Although there are no power reactors in Australia the problems and issues of public concern which arise in the operation of research reactors are similar to those of power reactors although on a smaller scale. The need for independent safety surveillance has been recognized by the Australian Government and the ANSTO Act, 1987, required the Board of ANSTO to establish a Nuclear Safety Bureau (NSB) with responsibility to the Minister for monitoring and reviewing the safety of nuclear plant operated by ANSTO. The Executive Director of ANSTO operates HIFAR subject to compliance with requirements and arrangements contained in a formal Authorization from the Board of ANSTO. A Ministerial Direction to the Board of ANSTO requires the NSB to report to him, on a quarterly basis, matters relating to its functions of monitoring and reviewing the safety of ANSTO's nuclear plant. Experience has shown that the Authorization provides a suitable framework for the operational requirements and arrangements to be organised in a disciplined and effective manner, and also provides a basis for audits by the NSB by which compliance with the Board's safety requirements are monitored. Examples of the way in which the NSB undertakes its monitoring and reviewing role are given. Moata, which has a much lower operating power level and fission product inventory than HIFAR, has not been subject to a formal Authorization to date but one is under preparation

Survey Result for the Safety Culture Attitude of HANARO in 2008

International Nuclear Information System (INIS)

Wu, Jong Sup; An, Seok Hwa

2009-01-01

One of the important aims of a nuclear management system is to foster a strong safety culture. The safety culture activities for HANARO have been implemented and the importance of safety management in nuclear activities has also been emphasized since its first operation. HANARO developed its own safety culture indicators by referring to the IAEA's documents for the purpose of the evaluation of the safety culture attitude. In June 2008 a survey on the safety culture was conducted based on the new safety culture indicators. The result of the survey shows that the safety culture activities contribute positively to its safe operation. But it is necessary to encourage some activities like training, resources and organizational culture. The survey was helpful to understand the general trends of the safety attitudes and to set the safety culture activities necessary for the improvement of its safe operation

Reliability Analysis of Public Survey in Satisfaction with Nuclear Safety

International Nuclear Information System (INIS)

Park, Moon Soo; Moon, Joo Hyun; Kang, Chang Sun

2005-01-01

Korea Institute of Nuclear Safety (KINS) carried out a questionnaire survey on public's understanding nuclear safety and regulation in order to grasp public acceptance for nuclear energy. The survey was planned to help to analyze public opinion on nuclear energy and provide basic data for advertising strategy and policy development. In this study, based on results of the survey, the reliability of the survey was evaluated according to each nuclear site

78 FR 12065 - Patient Safety Organizations: Delisting for Cause for Independent Data Safety Monitoring, Inc.

Science.gov (United States)

2013-02-21

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Agency for Healthcare Research and Quality Patient Safety... Safety Monitoring, Inc. due to its failure to correct a deficiency. The Patient Safety and Quality Improvement Act of 2005 (Patient Safety Act) authorizes the listing of PSOs, which are entities or component...

A sensor monitoring system for telemedicine, safety and security applications

Science.gov (United States)

Vlissidis, Nikolaos; Leonidas, Filippos; Giovanis, Christos; Marinos, Dimitrios; Aidinis, Konstantinos; Vassilopoulos, Christos; Pagiatakis, Gerasimos; Schmitt, Nikolaus; Pistner, Thomas; Klaue, Jirka

2017-02-01

A sensor system capable of medical, safety and security monitoring in avionic and other environments (e.g. homes) is examined. For application inside an aircraft cabin, the system relies on an optical cellular network that connects each seat to a server and uses a set of database applications to process data related to passengers' health, safety and security status. Health monitoring typically encompasses electrocardiogram, pulse oximetry and blood pressure, body temperature and respiration rate while safety and security monitoring is related to the standard flight attendance duties, such as cabin preparation for take-off, landing, flight in regions of turbulence, etc. In contrast to previous related works, this article focuses on the system's modules (medical and safety sensors and associated hardware), the database applications used for the overall control of the monitoring function and the potential use of the system for security applications. Further tests involving medical, safety and security sensing performed in an real A340 mock-up set-up are also described and reference is made to the possible use of the sensing system in alternative environments and applications, such as health monitoring within other means of transport (e.g. trains or small passenger sea vessels) as well as for remotely located home users, over a wired Ethernet network or the Internet.

Monitoring injury in the New Zealand adventure tourism sector: an operator survey.

Science.gov (United States)

Bentley, Tim A; Page, Stephen; Edwards, Joanna

2008-01-01

Client safety is a major risk management concern for the commercial adventure tourism sector in New Zealand. This study built on previous exploratory analyses of New Zealand adventure tourism safety, including industry surveys conducted by these authors in 1999 and 2003. The aims of the study were to provide a continuation of injury monitoring across the sector through data collected from self-reported injury incidence by industry operators and to compare findings with those from other primary and secondary research studies conducted by the authors. A postal questionnaire was used to survey all identifiable New Zealand adventure tourism operators during 2006. The questionnaire asked respondents about their recorded client injury experience, perceptions of client injury risk factors, and safety management practices. Some 21 adventure tourism activities were represented among the responding sample (n = 127), with most operations being very small in terms of staff numbers, although responding operators catered to nearly 1 million clients in total annually. Highest ranked risk factors for client injury included clients not following instructions; level of client skill, ability, and fitness; and changeable/unpredictable weather conditions. Highest client injury was reported for horse riding, ecotourism, and white water rafting sectors, although serious underreporting of minor injuries was evidenced across the sector. Slips, trips, and falls were the most frequently reported injury mechanism, while safety management measures were inconsistently applied across the sector. The industry should address reporting culture issues and safety management practices generally. Specifically, the industry should consider risk management that focuses on minor (eg, falls) as well as catastrophic events.

Reliability Analysis of Public Survey in Satisfaction with Nuclear Safety

Energy Technology Data Exchange (ETDEWEB)

Park, Moon Soo; Moon, Joo Hyun; Kang, Chang Sun [Seoul National Univ., Seoul (Korea, Republic of)

2005-07-01

Korea Institute of Nuclear Safety (KINS) carried out a questionnaire survey on public's understanding nuclear safety and regulation in order to grasp public acceptance for nuclear energy. The survey was planned to help to analyze public opinion on nuclear energy and provide basic data for advertising strategy and policy development. In this study, based on results of the survey, the reliability of the survey was evaluated according to each nuclear site.

Environmental Baseline Survey for Installation of Five New Hydrogeologic Groundwater Monitoring Wells

Energy Technology Data Exchange (ETDEWEB)

Catechis, Christopher S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-07-01

This Phase I Environmental Baseline Survey (EBS) provides the findings of a survey and assessment for termination of an existing easement granted to the Department of Energy (DOE) for the installation of 5 new hydrogeologic groundwater monitoring wells located on KAFB, New Mexico. The purpose of this EBS is to: Document the nature, magnitude, and extent of any environmental contamination of the property. Identify potential environmental contamination liabilities associated with the property. Develop sufficient information to assess the health and safety risks. Ensure adequate protection for human health and the environment related to a specific property. Determine possible effects of contamination on property valuation, and serve as the basis for notice of environmental condition for applicable federal or local real property disclosure requirements.

Development of a multilevel health and safety climate survey tool within a mining setting.

Science.gov (United States)

Parker, Anthony W; Tones, Megan J; Ritchie, Gabrielle E

2017-09-01

This study aimed to design, implement and evaluate the reliability and validity of a multifactorial and multilevel health and safety climate survey (HSCS) tool with utility in the Australian mining setting. An 84-item questionnaire was developed and pilot tested on a sample of 302 Australian miners across two open cut sites. A 67-item, 10 factor solution was obtained via exploratory factor analysis (EFA) representing prioritization and attitudes to health and safety across multiple domains and organizational levels. Each factor demonstrated a high level of internal reliability, and a series of ANOVAs determined a high level of consistency in responses across the workforce, and generally irrespective of age, experience or job category. Participants tended to hold favorable views of occupational health and safety (OH&S) climate at the management, supervisor, workgroup and individual level. The survey tool demonstrated reliability and validity for use within an open cut Australian mining setting and supports a multilevel, industry specific approach to OH&S climate. Findings suggested a need for mining companies to maintain high OH&S standards to minimize risks to employee health and safety. Future research is required to determine the ability of this measure to predict OH&S outcomes and its utility within other mine settings. As this tool integrates health and safety, it may have benefits for assessment, monitoring and evaluation in the industry, and improving the understanding of how health and safety climate interact at multiple levels to influence OH&S outcomes. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

Industrial safety and applied health physics. Annual report for 1977

International Nuclear Information System (INIS)

Auxier, J.A.; Davis, D.M.

1978-06-01

Progress is reported on the following: radiation monitoring with regard to personnel monitoring and health physics instrumentation; environs surveillance with regard to atmospheric monitoring, water monitoring, radiation background measurements, and soil and grass samples; radiation and safety surveys with regard to laboratory operations monitoring, radiation incidents, and laundry monitoring; industrial safety and special projects with regard to accident analysis, disabling injuries, and safety awards

Temelin safety monitor

International Nuclear Information System (INIS)

Mlady, O.

2000-01-01

Temelin NPP is a WWER-1000/320 two unit plant under construction, originally designed according to the standards of the former Soviet Union. After a series of reviews in the 80s, a decision was taken to upgrade the design of Temelin, including the supply of fuel and instrumentation and instrumentation and control system (I and C). Details on the current design and other related safety matters were presented to the nuclear community in a meeting organized by the IAEA in November 1994. Based upon recommendations of IAEA OSART missions, post TMI requirements and Temelin Risk Audit recommendations it was decided to perform a Probabilistic Safety Assessment within the Temelin PSA Project. The general purpose of this project was to perform systematic examination of the Temelin Unit 1 NPP for severe accident vulnerabilities by performance of a Level 1 and 2 PSA study. In addition to the completion of Temelin documented living PSA model, the decision was to develop and implement a PSA based software tool able to analyze real and scheduled plant conditions for determining the risk impact of plant configurations and on-line maintenance activities. This paper provides an overview of the key features of the Temelin Safety Monitor, describes its development activities and its current status and intended use at Temelin NPP for PSA applications. (author)

Measuring patient safety culture in Taiwan using the Hospital Survey on Patient Safety Culture (HSOPSC).

Science.gov (United States)

Chen, I-Chi; Li, Hung-Hui

2010-06-07

Patient safety is a critical component to the quality of health care. As health care organizations endeavour to improve their quality of care, there is a growing recognition of the importance of establishing a culture of patient safety. In this research, the authors use the Hospital Survey on Patient Safety Culture (HSOPSC) questionnaire to assess the culture of patient safety in Taiwan and attempt to provide an explanation for some of the phenomena that are unique in Taiwan. The authors used HSOPSC to measure the 12 dimensions of the patient safety culture from 42 hospitals in Taiwan. The survey received 788 respondents including physicians, nurses, and non-clinical staff. This study used SPSS 15.0 for Windows and Amos 7 software tools to perform the statistical analysis on the survey data, including descriptive statistics and confirmatory factor analysis of the structural equation model. The overall average positive response rate for the 12 patient safety culture dimensions of the HSOPSC survey was 64%, slightly higher than the average positive response rate for the AHRQ data (61%). The results showed that hospital staff in Taiwan feel positively toward patient safety culture in their organization. The dimension that received the highest positive response rate was "Teamwork within units", similar to the results reported in the US. The dimension with the lowest percentage of positive responses was "Staffing". Statistical analysis showed discrepancies between Taiwan and the US in three dimensions, including "Feedback and communication about error", "Communication openness", and "Frequency of event reporting". The HSOPSC measurement provides evidence for assessing patient safety culture in Taiwan. The results show that in general, hospital staffs in Taiwan feel positively toward patient safety culture within their organization. The existence of discrepancies between the US data and the Taiwanese data suggest that cultural uniqueness should be taken into

Hospital safety culture in Taiwan: a nationwide survey using Chinese version Safety Attitude Questionnaire.

Science.gov (United States)

Lee, Wui-Chiang; Wung, Hwei-Ying; Liao, Hsun-Hsiang; Lo, Chien-Ming; Chang, Fei-Ling; Wang, Pa-Chun; Fan, Angela; Chen, Hsin-Hsin; Yang, Han-Chuan; Hou, Sheng-Mou

2010-08-10

Safety activities have been initiated at many hospitals in Taiwan, but little is known about the safety culture at these hospitals. The aims of this study were to verify a safety culture survey instrument in Chinese and to assess hospital safety culture in Taiwan. The Taiwan Patient Safety Culture Survey was conducted in 2008, using the adapted Safety Attitude Questionnaire in Chinese (SAQ-C). Hospitals and their healthcare workers participated in the survey on a voluntary basis. The psychometric properties of the five SAQ-C dimensions were examined, including teamwork climate, safety climate, job satisfaction, perception of management, and working conditions. Additional safety measures were asked to assess healthcare workers' attitudes toward their collaboration with nurses, physicians, and pharmacists, respectively, and perceptions of hospitals' encouragement of safety reporting, safety training, and delivery delays due to communication breakdowns in clinical areas. The associations between the respondents' attitudes to each SAQ-C dimension and safety measures were analyzed by generalized estimating equations, adjusting for the clustering effects at hospital levels. A total of 45,242 valid questionnaires were returned from 200 hospitals with a mean response rate of 69.4%. The Cronbach's alpha was 0.792 for teamwork climate, 0.816 for safety climate, 0.912 for job satisfaction, 0.874 for perception of management, and 0.785 for working conditions. Confirmatory factor analyses demonstrated a good model fit for each dimension and the entire construct. The percentage of hospital healthcare workers holding positive attitude was 48.9% for teamwork climate, 45.2% for perception of management, 42.1% for job satisfaction, 37.2% for safety climate, and 31.8% for working conditions. There were wide variations in the range of SAQ-C scores in each dimension among hospitals. Compared to those without positive attitudes, healthcare workers with positive attitudes to each SAQ

Multi-dimensional database design and implementation of dam safety monitoring system

Directory of Open Access Journals (Sweden)

Zhao Erfeng

2008-09-01

Full Text Available To improve the effectiveness of dam safety monitoring database systems, the development process of a multi-dimensional conceptual data model was analyzed and a logic design was achieved in multi-dimensional database mode. The optimal data model was confirmed by identifying data objects, defining relations and reviewing entities. The conversion of relations among entities to external keys and entities and physical attributes to tables and fields was interpreted completely. On this basis, a multi-dimensional database that reflects the management and analysis of a dam safety monitoring system on monitoring data information has been established, for which factual tables and dimensional tables have been designed. Finally, based on service design and user interface design, the dam safety monitoring system has been developed with Delphi as the development tool. This development project shows that the multi-dimensional database can simplify the development process and minimize hidden dangers in the database structure design. It is superior to other dam safety monitoring system development models and can provide a new research direction for system developers.

2007 motor vehicle occupant safety survey. Volume 3, air bags report

Science.gov (United States)

2008-11-01

The 2007 Motor Vehicle Occupant Safety Survey was the sixth in a series of periodic national telephone surveys on occupant : protection issues conducted for the National Highway Traffic Safety Administration (NHTSA). Data collection was conducted : b...

78 FR 65661 - Agency Information Collection Activities; Proposed Collection; Comment Request; Food Safety Survey

Science.gov (United States)

2013-11-01

... are used to measure trends in consumer food safety habits including hand and cutting board washing... notice invites comments on a voluntary consumer survey entitled, ``Food Safety Survey.'' DATES: Submit... the safety of the nation's food supply. The Food Safety Survey measures consumers' knowledge...

Applied Health Physics and Safety annual report for 1975

International Nuclear Information System (INIS)

1976-08-01

This report describes and summarizes the activities of the applied sections and/or groups of the Health Physics Division. Projects and activities covered include personnel monitoring, environmental monitoring, radiation and safety surveys, and industrial safety

[Good clinical practices in clinical trials: the responsibility of the researcher. A survey of 827 hospital physicians (I). Availability. Monitoring. Safety. Contract].

Science.gov (United States)

Dal-Ré, R

1993-03-06

The Law of Medicaments establishes that clinical trials (CT) with drugs must be carried out following the of Good Clinical Practice guidelines (GCP). The attitude of hospital physicians to the GCP prior to its implementation as mandatory in accordance with Spanish legislation was considered to be of interest. An anonymous survey was used with closed response questions. Questions referring to the responsibilities of the investigator included in the GCP were included. From December 1988 to February 1990 the survey was distributed among 1,706 hospital medical staff members, of any specialty, who had or had not participated in CT. In this article the results of the questions regarding the availability of the investigative team, CT monitorization, management of adverse reactions, the safety of the participants in the CT and the contract between the sponsor and the researcher are presented. A total of 827 hospital doctors replied to the survey. Fifty-nine percent had intervened in CT with drugs. At least 94% of those surveyed considered that the researcher must have the time and number of eligible patients which the CT requires. There was high acceptance (> or = 78%) of the clinical audits to be performed by the health authorities and the sponsor company of the CT. The need of urgent communication of the severe adverse reactions is admitted by a great majority (> or = 95%) of those surveyed. Eighty-five percent believe that patients should be insured against damage derived from CT with 76% considering that the investigator should sign a contract with the sponsor; 68% and 59% would hand in a copy of the same to the CT committee and the remainder of the research team, respectively. According to the Good Clinical Practice dealt with in this article, the responsibilities of the investigator have been widely accepted by the hospital physicians surveyed, therefore no problems should be expected upon the implementation of the same in this country. However, the economic

Surveying wearable human assistive technology for life and safety critical applications: standards, challenges and opportunities.

Science.gov (United States)

Alam, Muhammad Mahtab; Ben Hamida, Elyes

2014-05-23

In this survey a new application paradigm life and safety for critical operations and missions using wearable Wireless Body Area Networks (WBANs) technology is introduced. This paradigm has a vast scope of applications, including disaster management, worker safety in harsh environments such as roadside and building workers, mobile health monitoring, ambient assisted living and many more. It is often the case that during the critical operations and the target conditions, the existing infrastructure is either absent, damaged or overcrowded. In this context, it is envisioned that WBANs will enable the quick deployment of ad-hoc/on-the-fly communication networks to help save many lives and ensuring people's safety. However, to understand the applications more deeply and their specific characteristics and requirements, this survey presents a comprehensive study on the applications scenarios, their context and specific requirements. It explores details of the key enabling standards, existing state-of-the-art research studies, and projects to understand their limitations before realizing aforementioned applications. Application-specific challenges and issues are discussed comprehensively from various perspectives and future research and development directions are highlighted as an inspiration for new innovative solutions. To conclude, this survey opens up a good opportunity for companies and research centers to investigate old but still new problems, in the realm of wearable technologies, which are increasingly evolving and getting more and more attention recently.

The new Basic Safety Standards Directive and its implications for environmental monitoring

International Nuclear Information System (INIS)

Janssens, Augustin; Necheva, Christina; Tanner, Vesa; Turai, István

2013-01-01

Monitoring of levels of radioactivity in the environment is enshrined in Chapter 3 of the Euratom Treaty, in particular its Articles 35 and 36. These requirements in primary law have had an important impact on the importance of monitoring in Europe but have not been worked out in much detail in secondary legislation. The consolidation and revision of the Basic Safety Standards Directive was an opportunity for doing so. The requirements in Directive 96/29/Euratom had remained rather general. Now, more specific text is introduced on the establishment of discharge authorisations for radioactive effluents, and on monitoring these discharges. Requirements on estimation of public exposures and on environmental monitoring programmes have largely been copied from the old basic safety standards (BSS), however. The main novelty of the new BSS is the introduction of exposure situations, as defined by the ICRP in Publication 103 (2007). Environmental monitoring as part of the management of an emergency exposure situation is now addressed more clearly. As for existing exposure situations, indoor exposure to radon requires extensive surveys of indoor air or soil concentrations, and precise requirements are made on the management of residues from industries processing naturally occurring radioactive materials (NORM) as well as on the monitoring of building materials. Although the BSS do not address specific monitoring issues, studies have been undertaken on effluents from hospitals and on long-term management of uranium mining areas. The proposal for the new Basic Safety Standards Directive is examined in the light of experience of the accident at Fukushima Dai-ichi Nuclear Power Plant disabled by the terrible tsunami on 11 March 2011. The arrangements for information exchange in a normal situation and in an emergency exposure situation need to be looked at from this perspective as well as from the perspective of smaller incidents such as the release of 131 I in Hungary in autumn

A hierarchical factor analysis of a safety culture survey.

Science.gov (United States)

Frazier, Christopher B; Ludwig, Timothy D; Whitaker, Brian; Roberts, D Steve

2013-06-01

Recent reviews of safety culture measures have revealed a host of potential factors that could make up a safety culture (Flin, Mearns, O'Connor, & Bryden, 2000; Guldenmund, 2000). However, there is still little consensus regarding what the core factors of safety culture are. The purpose of the current research was to determine the core factors, as well as the structure of those factors that make up a safety culture, and establish which factors add meaningful value by factor analyzing a widely used safety culture survey. A 92-item survey was constructed by subject matter experts and was administered to 25,574 workers across five multi-national organizations in five different industries. Exploratory and hierarchical confirmatory factor analyses were conducted revealing four second-order factors of a Safety Culture consisting of Management Concern, Personal Responsibility for Safety, Peer Support for Safety, and Safety Management Systems. Additionally, a total of 12 first-order factors were found: three on Management Concern, three on Personal Responsibility, two on Peer Support, and four on Safety Management Systems. The resulting safety culture model addresses gaps in the literature by indentifying the core constructs which make up a safety culture. This clarification of the major factors emerging in the measurement of safety cultures should impact the industry through a more accurate description, measurement, and tracking of safety cultures to reduce loss due to injury. Copyright © 2013 National Safety Council and Elsevier Ltd. All rights reserved.

Monitoring System For Improving Radiation Safety Management

International Nuclear Information System (INIS)

Osovizky, A.; Paran, J.; Tal, N.; Ankry, N.; Ashkenazi, B.; Tirosh, D.; Marziano, R.; Chisin, R.

1999-01-01

Medi SMARTS (Medical Survey Mapping Automatic Radiation Tracing System), a gamma radiation monitoring system, was installed in a nuclear medicine department. In this paper the evaluation of the system's ability to improve radiation safety management is presented. The system is based on a state of the art software that continuously collects on line radiation measurements for display, analysis and logging. Radiation is measured by GM tubes; the signal is transferred to a data processing unit and then via an RS-485 communication line to a computer. The system automatically identifies the detector type and its calibration factor, thus providing compatibility, maintainability and versatility when changing detectors. Radiation levels are displayed on the nuclear medicine department map at six locations. The system has been operating continuously for more than one year, documenting abnormal events caused by routine operation or failure incidents. In cases where abnormal working conditions were encountered, an alarm message was sent automatically to the supervisor via his tele-pager. An interesting issue observed during the system evaluation, was the inability to distinguish between high radiation levels caused by proper routine operation and those caused by safety failure incidents. The solution included examination of two parameters, radiation levels as well as their duration period. A careful analysis of the historical data, applying the appropriated combined parameters determined for each location, verified that such a system can identify abnormal events, provide alarms to warn in case of incidents and improve standard operating procedures

Practical Child Safety Education in England: A National Survey of the Child Safety Education Coalition

Science.gov (United States)

Mulvaney, Caroline A.; Watson, Michael C.; Walsh, Patrick

2013-01-01

Objective: To examine the provision of practical safety education by Child Safety Education Coalition (CSEC) organizations in England. Design: A postal survey. Setting: Providers of child practical safety education who were also part of CSEC. Methods: In February 2010 all CSEC organizations were sent a self-completion postal questionnaire which…

Geoelectrical Methods and Monitoring for Dam Safety Assessment, Republic of Korea

Science.gov (United States)

Lim, S. K.; Oldenburg, D.; Kang, S.; Song, S. H.

2016-12-01

Geoelectrical methods and monitoring to detect the seepage and internal erosion are essential for the safety assessment of earth dams. This work aims to develop improved methodologies to analyze the observed data and to monitor changes in seepage flow using direct current (DC) and self-potential (SP) methods. The seasonal variation of water level at dams causes a change in seepage and water saturation and hence alters the resistivity of the dam material. DC data are sensitive to water saturation and hence changes in saturation can be obtained by repeatedly measuring DC data. However, a more diagnostic parameter for safety assessment is fluid flow, and resistivity is only weakly coupled to that. Fortunately SP signals are directly related to fluid flow, and thus an SP survey has the potential to characterize fluid flow through the earth matrix. In Korea, the safety assessment of earth fill dams has been dealt by Korea Rural Community Corporation (KRC). Most of the dams are relatively old ( >50 years), hence assessing deterioration and corresponding seepage of those dams are crucial. In order to evaluate the engineering geological properties of the soil at earth dams in Korea, two boreholes in each dam were drilled to a bedrock depth that exceeds the height of the dam. A large set of field tests, including standard penetration tests (SPT) and in-situ permeability tests, were carried out along the boreholes. However, seepage paths in the dam is complex hence those limited measurements at a few points is not sufficient to delineate the zone of preferential seepage flow. For this, KRC developed permanent DC monitoring systems at a number of agricultural dams in Korea. The data were automatically collected every 6 hours. During the monitoring, the measurements of the water level at two boreholes were gathered at the same time. In this presentation we select an agricultural dam and delineate an anomalous leakage zone by inverting and interpreting time-lapse DC resistivity

The patient safety climate in healthcare organizations (PSCHO) survey: Short-form development.

Science.gov (United States)

Benzer, Justin K; Meterko, Mark; Singer, Sara J

2017-08-01

Measures of safety climate are increasingly used to guide safety improvement initiatives. However, cost and respondent burden may limit the use of safety climate surveys. The purpose of this study was to develop a 15- to 20-item safety climate survey based on the Patient Safety Climate in Healthcare Organizations survey, a well-validated 38-item measure of safety climate. The Patient Safety Climate in Healthcare Organizations was administered to all senior managers, all physicians, and a 10% random sample of all other hospital personnel in 69 private sector hospitals and 30 Veterans Health Administration hospitals. Both samples were randomly divided into a derivation sample to identify a short-form subset and a confirmation sample to assess the psychometric properties of the proposed short form. The short form consists of 15 items represented 3 overarching domains in the long-form scale-organization, work unit, and interpersonal. The proposed short form efficiently captures 3 important sources of variance in safety climate: organizational, work-unit, and interpersonal. The short-form development process was a practical method that can be applied to other safety climate surveys. This safety climate short form may increase response rates in studies that involve busy clinicians or repeated measures. Published 2017. This article is a U.S. Government work and is in the public domain in the USA.

Survey of radiological safety in dental practice

Energy Technology Data Exchange (ETDEWEB)

Gill, J R [UKAEA Health and Safety Branch, London; Hudson, A P

1977-01-01

A pilot survey of radiological protection in dental practice in Great Britain has been requested by the Health and Safety Executive and is now in progress. The survey should provide more precise data on the use of X-ray equipment. There are approximately 13,000 dentists in Great Britain using X-ray apparatus, and some 600 of these have been selected, on a statistical basis, to be invited to make use of a postal survey over a six month period. The postal survey technique to be used has already been developed as a service following requests from individual dentists. The dentist receives a questionnaire and three initial films to test the timer, then two special cassettes incorporating film and filters. Film badges are worn over a 12 week period by the dentist and by any staff who assist in radiography. Follow-up visits to discuss the survey will be made to one in ten of the selected dentists. The results will give the individual dentists, without cost, assurance of the efficient functioning of their equipment, and advice, should any remedial measures be necessary. Concurrently, the resulting statistics will give an indication of how many, if any, practices fall short of the recommendations of the Code of Practice for the Protection of Persons against Ionizing Radiations arising from Medical and Dental Use. Further action in respect of the Health and Safety at Work Act will be determined in the light of the survey.

Safety performance monitoring of autonomous marine systems

International Nuclear Information System (INIS)

Thieme, Christoph A.; Utne, Ingrid B.

2017-01-01

The marine environment is vast, harsh, and challenging. Unanticipated faults and events might lead to loss of vessels, transported goods, collected scientific data, and business reputation. Hence, systems have to be in place that monitor the safety performance of operation and indicate if it drifts into an intolerable safety level. This article proposes a process for developing safety indicators for the operation of autonomous marine systems (AMS). The condition of safety barriers and resilience engineering form the basis for the development of safety indicators, synthesizing and further adjusting the dual assurance and the resilience based early warning indicator (REWI) approaches. The article locates the process for developing safety indicators in the system life cycle emphasizing a timely implementation of the safety indicators. The resulting safety indicators reflect safety in AMS operation and can assist in planning of operations, in daily operational decision-making, and identification of improvements. Operation of an autonomous underwater vehicle (AUV) exemplifies the process for developing safety indicators and their implementation. The case study shows that the proposed process leads to a comprehensive set of safety indicators. It is expected that application of the resulting safety indicators consequently will contribute to safer operation of current and future AMS. - Highlights: • Process for developing safety indicators for autonomous marine systems. • Safety indicators based on safety barriers and resilience thinking. • Location of the development process in the system lifecycle. • Case study on AUV demonstrating applicability of the process.

Performance Monitoring for Nuclear Safety Related Instrumentation at PUSPATI TRIGA Reactor (RTP)

International Nuclear Information System (INIS)

Zareen Khan Abdul Jalil Khan; Ridzuan Abdul Mutalib; Mohd Sabri Minhat

2015-01-01

The Reactor TRIGA PUSPATI (RTP) at Malaysia Nuclear Agency is a TRIGA Mark II type reactor and pool type cooled by natural circulation of light water. This paper describe on performance monitoring for nuclear safety related instrumentation in TRIGA PUSPATI Reactor (RTP) of based on various parameter of reactor safety instrument channel such as log power, linear power, Fuel temperature, coolant temperature will take into consideration. Methodology of performance on estimation and monitoring is to evaluate and analysis of reactor parameters which is important of reactor safety and control. And also to estimate power measurement, differential of log and linear power and fuel temperature during reactor start-up, operation and shutdown .This study also focus on neutron power fluctuation from fission chamber during reactor start-up and operation. This work will present result of performance monitoring from RTP which indicated the safety parameter identification and initiate safety action on crossing the threshold set point trip. Conclude that performance of nuclear safety related instrumentation will improved the reactor control and safety parameter during reactor start-up, operation and shutdown. (author)

Safety valve opening and closing operation monitor

International Nuclear Information System (INIS)

Kodama, Kunio; Takeshima, Ikuo; Takahashi, Kiyokazu.

1981-01-01

Purpose: To enable the detection of the closing of a safety valve when the internal pressure in a BWR type reactor is a value which will close the safety valve, by inputting signals from a pressure detecting device mounted directly at a reactor vessel and a safety valve discharge pressure detecting device to an AND logic circuit. Constitution: A safety valve monitor is formed of a pressure switch mounted at a reactor pressure vessel, a pressure switch mounted at the exhaust pipe of the escape safety valve and a logic circuit and the lide. When the input pressure of the safety valve is raised so that the valve and the pressure switch mounted at the exhaust pipe are operated, an alarm is indicated, and the operation of the pressure switch mounted at a pressure vessel is eliminated. If the safety valve is not reclosed when the vessel pressure is decreased lower than the pressure at which it is to be reclosed after the safety valve is operated, an alarm is generated by the logic circuit since both the pressure switches are operated. (Sekiya, K.)

Safety culture in regulatory expert organization : analysis result of survey for KINS employees

International Nuclear Information System (INIS)

Choi, G. S.; Choi, Y. S.

2003-01-01

Much has been discussed on safety culture of operating organizations, however, little has been done on that of regulatory organization. Current issues and activities related to nuclear safety culture at IAEA, OECD/NEA, etc. were investigated and relevant literatures were reviewed. Elements essential for safety culture of regulatory organization were proposed and survey questionnaire for employees of regulatory expert organization, KINS, was developed based on the elements proposed. The survey result was presented and its implications were discussed. Based on the result, elements of safety culture in regulatory organization were proposed. The result of this survey can be used in developing safety culture model of regulatory organization, measurement method and also promotion of safety culture in regulatory organization

International survey of living PSA and safety indicators

International Nuclear Information System (INIS)

Holmberg, J.; Laakso, K.; Lehtinen, E.; Bjoere, S.

1992-01-01

The report contains an international overview of applications of living probabilistic assessment and development of operational safety indicators. Features of an ideal living PSA tool are summarized as well as a limited survey of code systems for managing a living probabilistic safety assessment (living PSA) is included. The international survey is used as an input for planning and performance of related tasks within the nordic NKS/SIK-1 project conducted in 1990-93. The research notes are distributed to the Nordic organizations involved or interested in the subject. The report includes an overview and conclusions from technical reports and articles available and presentations and discussions related to development and use of above methods for the evaluation and management of the operational safety of nuclear power plants. A large part of this material is based on material collected and discussed in connection to international specialist meetings relating to the subject

Environmental and Source Monitoring for Purposes of Radiation Protection. Safety Guide (Spanish ed.)

International Nuclear Information System (INIS)

2010-01-01

The purpose of this Safety Guide is to provide international guidance, coherent with contemporary radiation protection principles and IAEA safety requirements, on the strategy of monitoring in relation to: (a) control of radionuclide discharges under practice conditions, and (b) intervention, such as in cases of nuclear or radiological emergencies or past contamination of areas with long lived radionuclides. Three categories of monitoring are discussed: monitoring at the source of the discharge (source monitoring), monitoring in the environment (environmental monitoring) and monitoring of individual exposure in emergencies (individual monitoring). The Safety Guide also provides general guidance on assessment of the doses to critical groups of the population due to the presence of radioactive materials or radiation fields in the environment both from routine operation of nuclear and other related facilities (practice) and from nuclear or radiological emergencies and past contamination of areas with long lived radionuclides (intervention). The dose assessments are based on the results of source monitoring, environmental monitoring, individual monitoring or their combinations. This Safety Guide is primarily intended for use by national regulatory bodies and other agencies involved in national systems of radiation monitoring, as well as by operators of nuclear installations and other facilities where natural or human made radionuclides are treated and monitored. Contents: 1. Introduction; 2. Meeting regulatory requirements for monitoring in practices and interventions; 3. Responsibilities for monitoring; 4. Generic aspects of monitoring programmes; 5. Programmes for monitoring in practices and interventions; 6. Technical conditions for monitoring procedures; 7. Considerations in dose assessment; 8. Interpretation of monitoring results; 9. Quality assurance; 10. Recording of results; 11. Education and training; Glossary.

Leadership Actions to Improve Nuclear Safety Culture

International Nuclear Information System (INIS)

Clewett, L.K.

2016-01-01

The challenge many leaders face is how to effectively implement and then utilise the results of Safety Culture surveys. Bruce Power has recently successfully implemented changes to the Safety Culture survey process including how corrective actions were identified and implemented. The actions taken in response to the latest survey have proven effective with step change performance noted. Nuclear Safety is a core value for Bruce Power. Nuclear Safety at Bruce Power is based on the following four pillars: reactor safety, industrial safety, radiological safety and environmental safety. Processes and practices are in place to achieve a healthy Nuclear Safety Culture within Bruce Power such that nuclear safety is the overriding priority. This governance is based on industry leading practices which monitor, asses and take action to drive continual improvements in the Nuclear Safety Culture within Bruce Power.

Geothermal energy, an environmental and safety mini-overview survey

Energy Technology Data Exchange (ETDEWEB)

1976-07-01

A survey is presented in order to determine the technology status, gaps, and needs for research and development programs in the environment and safety areas of this resource. The information gathered from a survey of geothermal energy development undertaken to provide background for an environment and safety overview program is summarized. A technology assessment for resource development is presented. The three specific environmental problems identified as most potentially limiting to geothermal development; hydrogen sulfide control, brine disposal, and subsidence, are discussed. Current laws, regulations, and standards applying to geothermal systems are summarized. The elements of the environment, health, and safety program considered to be intrinsically related to the development of geothermal energy systems are discussed. Interagency interfaces are touched on briefly. (MHR)

A survey of approaches combining safety and security for industrial control systems

International Nuclear Information System (INIS)

Kriaa, Siwar; Pietre-Cambacedes, Ludovic; Bouissou, Marc; Halgand, Yoran

2015-01-01

The migration towards digital control systems creates new security threats that can endanger the safety of industrial infrastructures. Addressing the convergence of safety and security concerns in this context, we provide a comprehensive survey of existing approaches to industrial facility design and risk assessment that consider both safety and security. We also provide a comparative analysis of the different approaches identified in the literature. - Highlights: • We raise awareness of safety and security convergence in numerical control systems. • We highlight safety and security interdependencies for modern industrial systems. • We give a survey of approaches combining safety and security engineering. • We discuss the potential of the approaches to model safety and security interactions

Report by USSR survey mission of Nuclear Safety Commission

International Nuclear Information System (INIS)

1990-01-01

The USSR survey mission of Nuclear Safety Commission drew up and presents the report as follows. In relation to the accident in Chernobyl Nuclear Power Station in USSR, in order to investigate into the present status of the countermeasures for nuclear power safety in USSR and to exchange opinion, the USSR survey mission inspected nuclear power station facilities and visited the government organs, research institutes and others in USSR. The survey mission comprised 13 members, and went to Moscow, Kiev and two nuclear power station sites, from October 22 to November 1, 1989, for 11 days. At present in USSR, 49 nuclear power plants of about 35 GWe are in operation, and by 2000, the operation of more nuclear power plants of about 30 GWe is needed, but due to the change of social situation in USSR, its attainment seems to be difficult. The plan of nuclear power generation in USSR, the ensuring of safety in general, the recent countermeasures for improving safety, the effect of the accident in Chenobyl Nuclear Power Station on health and so on are reported. The detailed record of the visit to Zaporozhe and Chernobyl Nuclear Power Stations and 7 other research institutes and government organs is given. (K.I.)

Potential of acoustic monitoring for safety assessment of primary system

International Nuclear Information System (INIS)

Olma, B.J.

1997-01-01

Safety assessment of the primary system and its components with respect to their mechanical integrity is increasingly supported by acoustic signature analysis during power operation of the plants. Acoustic signals of Loose Parts Monitoring System sensors are continuously monitored by dedicated digital systems for signal bursts associated with metallic impacts. Several years of ISTec/GRS experience and the practical use of its digital systems MEDEA and RAMSES have shown that acoustic monitoring is very successful for detecting component failures at an early stage. Advanced powerful tools for classification and acoustic evaluation of burst signals have recently been realized. The paper presents diagnosis experiences of BWR's and PWR's safety assessment. (author). 7 refs, 8 figs

Plastic-bag radon gas monitor and survey results

International Nuclear Information System (INIS)

Torri, G.

1990-01-01

The Plastic-bag radon monitor used in the Italian National Survey is described. The choice of this radon gas sampler has been determined by the peculiarity of the italian environmental monitoring program, which is carried out by several different regional laboratories. Results obtained in the past using this radon monitoring device are also reported. (author). 8 refs, 7 figs

[Establishment of model of traditional Chinese medicine injections post-marketing safety monitoring].

Science.gov (United States)

Guo, Xin-E; Zhao, Yu-Bin; Xie, Yan-Ming; Zhao, Li-Cai; Li, Yan-Feng; Hao, Zhe

2013-09-01

To establish a nurse based post-marketing safety surveillance model for traditional Chinese medicine injections (TCMIs). A TCMIs safety monitoring team and a research hospital team engaged in the research, monitoring processes, and quality control processes were established, in order to achieve comprehensive, timely, accurate and real-time access to research data, to eliminate errors in data collection. A triage system involving a study nurse, as the first point of contact, clinicians and clinical pharmacists was set up in a TCM hospital. Following the specified workflow involving labeling of TCM injections and using improved monitoring forms it was found that there were no missing reports at the ratio of error was zero. A research nurse as the first and main point of contact in post-marketing safety monitoring of TCM as part of a triage model, ensures that research data collected has the characteristics of authenticity, accuracy, timeliness, integrity, and eliminate errors during the process of data collection. Hospital based monitoring is a robust and operable process.

Survey of hydrogen monitoring devices

International Nuclear Information System (INIS)

Lai, W.

1981-01-01

Presented are results of a survey of commercially available monitoring devices suitable for hydrogen detection in the secondary containment vessel of a nuclear power plant during the post postulated accident period. Available detectors were grouped into the following five classes: combustion, solid state, electrochemical, thermal conductivity, and absorption. The performance of most available sensors is likely to deteriorate when exposed to the postulated conditions which include moisture, which could be at high temperature, and radioactive noncondensibles. Of the commercial devices, those using metallic filament thermal conductivity detectors seem least susceptible to performance change. Absorption detectors are best suited for this monitoring task but the only available device is designed for pipeline corrosion assessment. Initiation of experimental study to assess apparent deficiencies of commercial detectors is recommended. Also recommended is an analytical/experimental effort to determine the optimum detector array for monitoring in the secondary containment vessels

Maintaining Oversight of Licensee Safety Culture. CSNI/WGHOF Survey Results

International Nuclear Information System (INIS)

2008-01-01

In preparation for this workshop, a survey was sent to members of the WGHOF in Autumn 2006. Purpose of the Survey was to explore and share the methods and approaches used to maintain oversight of licensee safety culture. 13 countries responded to the survey. The responses were used in the development of discussion topics and themes for this workshop. This presentation (slides) summarizes the results of the survey

Occupational safety issues in residential construction surveyed in Wisconsin, United States.

Science.gov (United States)

Choi, Sang D; Carlson, Kathryn

2014-01-01

Residential construction is a high-risk industry in the U.S. due to the exposure to work-related safety hazards and fall injuries. This study aimed to examine the safety training and safe work practices of construction workers within the small residential construction industry. In order to achieve the study objectives, a survey was designed and sent to approximately 200 Wisconsin based residential construction contractors. About one third of the respondents stated that they did not have any form of safety programs. The study indicated that the most common types of work-related injuries in residential construction were slips/trips/falls and cuts/lacerations. The survey findings also suggested that the residential construction contractors needed to increase the utilization of fall protection safety equipment. Further education and subject matter expert training could provide benefits to improve occupational safety and health of the small business workforce in the residential construction industry.

Design of Safety Parameter Monitoring Function in a Research Reactor Facility

Energy Technology Data Exchange (ETDEWEB)

Park, Jaekwan; Suh, Yongsuk [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

The primary purpose of the safety parameter monitoring system (SPDS) is to help operating personnel in the control room make quick assessments of the plant safety status. Thus, the basic function of the SPDS is a provision of a continuous indication of plant parameters or derived variables representative of the safety status of the plant. NUREG-0737 Supplement 1 provides details of the functional criteria for the SPDS, as one of the action plan requirements from TMI accident. The system provides various functions as follows: · Alerting based on safety function decision logics, · Success path analysis to achieve the integrity of the safety functions, · 3 layer display architecture - safety function, success path display for each safety function, system summary and equipment details for each safety function, · Integration with computer-based procedure. According to a Notice of the NSSC No. 2012-31, a research reactor facility generating more than 2 MW of power should also be furnished with the SPDS for emergency preparedness. Generally, a research reactor is a small size facility, and its number of instrumentations is fewer than that of NPPs. In particular, it is actually hard to have various and powerful functions from an economic perspective. Therefore, a safety parameter display system optimized for a research reactor facility must be proposed. This paper provides the requirement analysis results and proposes the design of safety parameter monitoring function for a research reactor. The safety parameter monitoring function supporting control room personnel during emergency conditions should be designed in a research reactor facility. The facility size and number of signals are smaller than that of the power plants. Also, it is actually hard to have various and powerful functions of nuclear power plants from an economic perspective. Thus, a safety parameter display system optimized to a research reactor must be proposed. First, we found important design items

Design of Safety Parameter Monitoring Function in a Research Reactor Facility

International Nuclear Information System (INIS)

Park, Jaekwan; Suh, Yongsuk

2014-01-01

The primary purpose of the safety parameter monitoring system (SPDS) is to help operating personnel in the control room make quick assessments of the plant safety status. Thus, the basic function of the SPDS is a provision of a continuous indication of plant parameters or derived variables representative of the safety status of the plant. NUREG-0737 Supplement 1 provides details of the functional criteria for the SPDS, as one of the action plan requirements from TMI accident. The system provides various functions as follows: · Alerting based on safety function decision logics, · Success path analysis to achieve the integrity of the safety functions, · 3 layer display architecture - safety function, success path display for each safety function, system summary and equipment details for each safety function, · Integration with computer-based procedure. According to a Notice of the NSSC No. 2012-31, a research reactor facility generating more than 2 MW of power should also be furnished with the SPDS for emergency preparedness. Generally, a research reactor is a small size facility, and its number of instrumentations is fewer than that of NPPs. In particular, it is actually hard to have various and powerful functions from an economic perspective. Therefore, a safety parameter display system optimized for a research reactor facility must be proposed. This paper provides the requirement analysis results and proposes the design of safety parameter monitoring function for a research reactor. The safety parameter monitoring function supporting control room personnel during emergency conditions should be designed in a research reactor facility. The facility size and number of signals are smaller than that of the power plants. Also, it is actually hard to have various and powerful functions of nuclear power plants from an economic perspective. Thus, a safety parameter display system optimized to a research reactor must be proposed. First, we found important design items

Development of Operational Safety Monitoring System and Emergency Preparedness Advisory System for CANDU Reactors (I)

International Nuclear Information System (INIS)

Kim, Ma Woong; Shin, Hyeong Ki; Lee, Sang Kyu; Kim, Hyun Koon; Yoo, Kun Joong; Ryu, Yong Ho; Son, Han Seong; Song, Deok Yong

2007-01-01

As increase of operating nuclear power plants, an accident monitoring system is essential to ensure the operational safety of nuclear power plant. Thus, KINS has developed the Computerized Advisory System for a Radiological Emergency (CARE) system to monitor the operating status of nuclear power plant continuously. However, during the accidents or/and incidents some parameters could not be provided from the process computer of nuclear power plant to the CARE system due to limitation of To enhance the CARE system more effective for CANDU reactors, there is a need to provide complement the feature of the CARE in such a way to providing the operating parameters using to using safety analysis tool such as CANDU Integrated Safety Analysis System (CISAS) for CANDU reactors. In this study, to enhance the safety monitoring measurement two computerized systems such as a CANDU Operational Safety Monitoring System (COSMOS) and prototype of CANDU Emergency Preparedness Advisory System (CEPAS) are developed. This study introduces the two integrated safety monitoring system using the R and D products of the national mid- and long-term R and D such as CISAS and ISSAC code

Survey of electronic safety systems in accelerator applications

International Nuclear Information System (INIS)

Mahoney, K.

1997-01-01

This paper presents the preliminary results and analysis of a comprehensive survey of the implementation of accelerator safety interlock systems from over 30 international labs. At the present time there is not a self consistent means to evaluate both the experiences and level of protection provided by electronic safety interlock systems. This research is intended to analyze the strength and weaknesses of several different types of interlock system implementation methodologies. Research, medical, and industrial accelerators are compared. Thomas Jefferson National Accelerator Facility (TJNAF) was one of the first large particle accelerators to implement a safety interlock system using programmable logic controllers. Since that time all of the major new U.S. accelerator construction projects plan to use some form of programmable electronics as part of a safety interlock system in some capacity

"Against the silence": Development and first results of a patient survey to assess experiences of safety-related events in hospital

Directory of Open Access Journals (Sweden)

Schwappach David LB

2008-03-01

and dietary intake. Overall, the in-depth interviews confirmed experiences from the focus groups that many patients feel reluctant to report undesirable events without acknowledging the presence or absence of individual responsibility or failure. Many patients reported that they did not ask or communicate about errors or near misses with staff and some patients even develop strategies to improve their safety but do not disclose these to staff. Conclusion Many patients experience undesirable events during hospitalization and a significant number of patients is seriously concerned about their safety. Surveying patients about experiences with safety-related events in hospital seems a valuable tool for identifying and monitoring problematic areas of care and undesirable events. Evidence from the qualitative interviews indicates that safety remains an unsaid word between patients and their care providers.

[Necessity of applying pharmacovigilance in post-marketing safety monitoring of traditional Chinese medicine injections].

Science.gov (United States)

Wang, Hai-Nan; Chen, Wen; Fu, Zheng; Du, Wen-min; He, Jia

2008-03-01

Traditional Chinese medicine (TCM) injection has become one of the hotspots in the new TCM research and development. The serious adverse drug reactions happened in clinical have arosed attention widely in the whole society. It's very urgent to monitor the post-marketing safety of TCM injections. This paper elucidated the pharmacovigilance's necessity in the post-marketing safety monitoring of TCM injections, basing on the reason of safety problem of TCM injections and the future developing trend of adverse drug reaction monitoring. Also, this paper introduced the rapid signal detection method of spontaneous reporting system database by data mining technology.

Safety measurement and monitoring in healthcare: a framework to guide clinical teams and healthcare organisations in maintaining safety

Science.gov (United States)

Vincent, Charles; Burnett, Susan; Carthey, Jane

2014-01-01

Patients, clinicians and managers all want to be reassured that their healthcare organisation is safe. But there is no consensus about what we mean when we ask whether a healthcare organisation is safe or how this is achieved. In the UK, the measurement of harm, so important in the evolution of patient safety, has been neglected in favour of incident reporting. The use of softer intelligence for monitoring and anticipation of problems receives little mention in official policy. The Francis Inquiry report into patient treatment at the Mid Staffordshire NHS Foundation Trust set out 29 recommendations on measurement, more than on any other topic, and set the measurement of safety an absolute priority for healthcare organisations. The Berwick review found that most healthcare organisations at present have very little capacity to analyse, monitor or learn from safety and quality information. This paper summarises the findings of a more extensive report and proposes a framework which can guide clinical teams and healthcare organisations in the measurement and monitoring of safety and in reviewing progress against safety objectives. The framework has been used so far to promote self-reflection at both board and clinical team level, to stimulate an organisational check or analysis in the gaps of information and to promote discussion of ‘what could we do differently’. PMID:24764136

Monitor for safety engineering facility

International Nuclear Information System (INIS)

Sato, Akira; Kaneda, Mitsunori.

1982-01-01

Purpose: To improve the reactor safety and decrease misoperation upon periodical inspection by instantly obtaining the judgement for the stand-by states in engineering safety facilities of a nuclear power plant. Constitution: Process inputs representing the states of valves, pumps, flowrates or the likes of the facility are gathered into an input device and inputted to a status monitor. The status of the facility inputted to the input device are judged for each of the inputs in a judging section and recognized as a present system stand-by pattern of the system (Valve) to be inspected. While on the other hand, a normal system stand-by pattern previously stored in a memory unit is read out by an instruction from an operator console and judged by comparison with the system stand-by pattern in a comparison section. The results are displayed on a display device. Upon periodical inspection, inspection procedures stored in the memory unit are displayed on the display device by the instruction from the operator console. (Seki, T.)

Report on the results of the safety culture survey conducted in PNRI

International Nuclear Information System (INIS)

Garcia, Corazon M.; Nohay, Carl M.; Badinas, Nelson P.; Melendez, Johnylen V.; Parami, Vangeline K.

2001-01-01

An initial safety culture survey was conducted in the Philippine Nuclear Research Institute (PNRI). Sixty six (66) questionnaires as given in A. Adams and A. Williamson's Measurement of Safety Culture in the Nuclear Industry, UNSW, July 1999 were distributed to the different units of PNRI. The number of sets of survey sheets distributed to the different units corresponded to the number of personnel in the unit based on the information obtained from them. Results were obtained from only 33 respondents. ANSTO has been requested to analyze the results of this survey. While waiting for the results from ANSTO, we attempted to proceed with this analysis in order to learn and practice applying the procedure based on the reference cited above.The respondents from the PNRI showed on the overall neutral views towards safety and their work. Although a minority showed positive responses to safety while a small minority showed negative responses. A remarkable result is that all respondents show strong concern over the welfare of the institute, indicating that there is still a good chance for safety culture to be developed positively among the employees given the proper strategies for motivation. (author)

Neural Net Safety Monitor Design

Science.gov (United States)

Larson, Richard R.

2007-01-01

The National Aeronautics and Space Administration (NASA) at the Dryden Flight Research Center (DFRC) has been conducting flight-test research using an F-15 aircraft (figure 1). This aircraft has been specially modified to interface a neural net (NN) controller as part of a single-string Airborne Research Test System (ARTS) computer with the existing quad-redundant flight control system (FCC) shown in figure 2. The NN commands are passed to FCC channels 2 and 4 and are cross channel data linked (CCDL) to the other computers as shown. Numerous types of fault-detection monitors exist in the FCC when the NN mode is engaged; these monitors would cause an automatic disengagement of the NN in the event of a triggering fault. Unfortunately, these monitors still may not prevent a possible NN hard-over command from coming through to the control laws. Therefore, an additional and unique safety monitor was designed for a single-string source that allows authority at maximum actuator rates but protects the pilot and structural loads against excessive g-limits in the case of a NN hard-over command input. This additional monitor resides in the FCCs and is executed before the control laws are computed. This presentation describes a floating limiter (FL) concept1 that was developed and successfully test-flown for this program (figure 3). The FL computes the rate of change of the NN commands that are input to the FCC from the ARTS. A window is created with upper and lower boundaries, which is constantly floating and trying to stay centered as the NN command rates are changing. The limiter works by only allowing the window to move at a much slower rate than those of the NN commands. Anywhere within the window, however, full rates are allowed. If a rate persists in one direction, it will eventually hit the boundary and be rate-limited to the floating limiter rate. When this happens, a persistent counter begins and after a limit is reached, a NN disengage command is generated. The

Workforce perceptions of hospital safety culture: development and validation of the patient safety climate in healthcare organizations survey.

Science.gov (United States)

Singer, Sara; Meterko, Mark; Baker, Laurence; Gaba, David; Falwell, Alyson; Rosen, Amy

2007-10-01

To describe the development of an instrument for assessing workforce perceptions of hospital safety culture and to assess its reliability and validity. Primary data collected between March 2004 and May 2005. Personnel from 105 U.S. hospitals completed a 38-item paper and pencil survey. We received 21,496 completed questionnaires, representing a 51 percent response rate. Based on review of existing safety climate surveys, we developed a list of key topics pertinent to maintaining a culture of safety in high-reliability organizations. We developed a draft questionnaire to address these topics and pilot tested it in four preliminary studies of hospital personnel. We modified the questionnaire based on experience and respondent feedback, and distributed the revised version to 42,249 hospital workers. We randomly divided respondents into derivation and validation samples. We applied exploratory factor analysis to responses in the derivation sample. We used those results to create scales in the validation sample, which we subjected to multitrait analysis (MTA). We identified nine constructs, three organizational factors, two unit factors, three individual factors, and one additional factor. Constructs demonstrated substantial convergent and discriminant validity in the MTA. Cronbach's alpha coefficients ranged from 0.50 to 0.89. It is possible to measure key salient features of hospital safety climate using a valid and reliable 38-item survey and appropriate hospital sample sizes. This instrument may be used in further studies to better understand the impact of safety climate on patient safety outcomes.

Indicators to monitor NPP operational safety performance

International Nuclear Information System (INIS)

Gomez-Cobo, Ana

2002-01-01

Since December 1995 the IAEA activities on safety performance indicators focused on the elaboration of a framework for the establishment of an operational safety performance indicator programme. The development of this framework began with the consideration of the concept of NPP operational safety performance and the identification of operational safety attributes. For each operational safety attribute, overall indicators, envisioned as providing an overall evaluation of relevant aspects of safety performance, were established. Associated with each overall indicator is a level of strategic indicators intended to provide a bridge from overall to specific indicators. Finally each strategic indicator was supported by a set of specific indicators, which represent quantifiable measures of performance. The programme development was enhanced by pilot plant studies, conducted over a 15 month period from January 1998 to March 1999. The result of all this work is compiled in the IAEA-TECDOC-1141, to be published shortly. This paper presents a summary of this IAEA TECDOC. It describes the operational safety performance indicator framework proposed and discusses the results of and lessons learned from the pilot studies. Despite the efforts described, it is clear that additional research is still necessary in areas such as plant-specific adaptation of proposed frameworks in order to suit individual data collection systems and plant characteristics, indicator selection, indicator definition, goal setting, action thresholds, analysis of trends, indicator display systems, analysis of overall safety performance (i.e., aggregation or combination of indicators), safety culture indicators, qualitative indicators, and use of additional indicators to address issues such as industrial safety attitude and performance, staff welfare, and environmental compliance. This is the rationale for a new IAEA Coordinated Research Project on 'Development and application of indicators to monitor NPP

Survey monitoring of environmental radioactivity in Busan area

Energy Technology Data Exchange (ETDEWEB)

Yang, H. S.; Lee, J. [Busan Regional Monitoring Station, Busan (Korea, Republic of)

2000-12-15

At Pusan Regional Monitoring Station in Busan have been measured periodically in 2000 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Gamma nuclides in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Pusan, vegetables, fishes, shellfish, drinking water (total 23ea) samples were taken from sampling sites which were selected by KlNS. We analysis gamma nuclide for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzing an gamma nuclide concentration in environmental samples in Pusan are fee of radiological contaminants.

Survey monitoring of environmental radioactivity in Busan area

Energy Technology Data Exchange (ETDEWEB)

Yang, Han Soeb; Jang, Young A. [Busan Regional Monitoring Station, Busan (Korea, Republic of)

2003-12-15

At Regional Radioactivity Monitoring Station in Pusan have been measured periodically in 2003 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Gamma nuclides in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Busan foodstuffs, dust, drinking water (total 24ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma nuclide for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzing an gamma nuclide concentration in environmental samples in Pusan are fee of radiological contaminants.

Survey monitoring of environmental radioactivity in Busan area

International Nuclear Information System (INIS)

Yang, Han Soeb; Jang, Young A.

2003-12-01

At Regional Radioactivity Monitoring Station in Pusan have been measured periodically in 2003 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Gamma nuclides in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Busan foodstuffs, dust, drinking water (total 24ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma nuclide for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzing an gamma nuclide concentration in environmental samples in Pusan are fee of radiological contaminants

Selection of indicators for continuous monitoring of patient safety: recommendations of the project 'safety improvement for patients in Europe'

DEFF Research Database (Denmark)

Kristensen, Solvejg; Mainz, Jan; Bartels, Paul

2009-01-01

such as culture, infections, surgical complications, medication errors, obstetrics, falls and specific diagnostic areas. CONCLUSION: The patient safety indicators recommended present a set of possible measures of patient safety. One of the future perspectives of implementing patient safety indicators...... for systematic monitoring is that it will be possible to continuously estimate the prevalence and incidence of patient safety quality problems. The lesson learnt from quality improvement is that it will pay off in terms of improving patient safety....

Monitoring work zone safety and mobility impacts in Texas.

Science.gov (United States)

2009-05-01

In this report, Texas Transportation Institute researchers identify key work zone safety and mobility : performance measures that the Texas Department of Transportation (TxDOT) should target as part of a work : zone monitoring program within a distri...

Monitoring beach changes using GPS surveying techniques

Science.gov (United States)

Morton, Robert; Leach, Mark P.; Paine, Jeffrey G.; Cardoza, Michael A.

1993-01-01

A need exists for frequent and prompt updating of shoreline positions, rates of shoreline movement, and volumetric nearshore changes. To effectively monitor and predict these beach changes, accurate measurements of beach morphology incorporating both shore-parallel and shore-normal transects are required. Although it is possible to monitor beach dynamics using land-based surveying methods, it is generally not practical to collect data of sufficient density and resolution to satisfy a three-dimensional beach-change model of long segments of the coast. The challenge to coastal scientists is to devise new beach monitoring methods that address these needs and are rapid, reliable, relatively inexpensive, and maintain or improve measurement accuracy.

National Highway Traffic Safety Administration 1995 customer satisfaction survey

Science.gov (United States)

1996-05-01

The National Highway Traffic Safety Administration (NHTSA) conducted a national Customer Satisfaction Survey in response to the requirements of the National Performance Review and Executive Order 12862. An independent research organization, Schulman,...

Patient safety in primary care: a survey of general practitioners in the Netherlands

Directory of Open Access Journals (Sweden)

Wensing Michel

2010-01-01

Full Text Available Abstract Background Primary care encompasses many different clinical domains and patient groups, which means that patient safety in primary care may be equally broad. Previous research on safety in primary care has focused on medication safety and incident reporting. In this study, the views of general practitioners (GPs on patient safety were examined. Methods A web-based survey of a sample of GPs was undertaken. The items were derived from aspects of patient safety issues identified in a prior interview study. The questionnaire used 10 clinical cases and 15 potential risk factors to explore GPs' views on patient safety. Results A total of 68 GPs responded (51.5% response rate. None of the clinical cases was uniformly judged as particularly safe or unsafe by the GPs. Cases judged to be unsafe by a majority of the GPs concerned either the maintenance of medical records or prescription and monitoring of medication. Cases which only a few GPs judged as unsafe concerned hygiene, the diagnostic process, prevention and communication. The risk factors most frequently judged to constitute a threat to patient safety were a poor doctor-patient relationship, insufficient continuing education on the part of the GP and a patient age over 75 years. Language barriers and polypharmacy also scored high. Deviation from evidence-based guidelines and patient privacy in the reception/waiting room were not perceived as risk factors by most of the GPs. Conclusion The views of GPs on safety and risk in primary care did not completely match those presented in published papers and policy documents. The GPs in the present study judged a broader range of factors than in previously published research on patient safety in primary care, including a poor doctor-patient relationship, to pose a potential threat to patient safety. Other risk factors such as infection prevention, deviation from guidelines and incident reporting were judged to be less relevant than by policy

Patient safety in primary care: a survey of general practitioners in The Netherlands.

Science.gov (United States)

Gaal, Sander; Verstappen, Wim; Wensing, Michel

2010-01-21

Primary care encompasses many different clinical domains and patient groups, which means that patient safety in primary care may be equally broad. Previous research on safety in primary care has focused on medication safety and incident reporting. In this study, the views of general practitioners (GPs) on patient safety were examined. A web-based survey of a sample of GPs was undertaken. The items were derived from aspects of patient safety issues identified in a prior interview study. The questionnaire used 10 clinical cases and 15 potential risk factors to explore GPs' views on patient safety. A total of 68 GPs responded (51.5% response rate). None of the clinical cases was uniformly judged as particularly safe or unsafe by the GPs. Cases judged to be unsafe by a majority of the GPs concerned either the maintenance of medical records or prescription and monitoring of medication. Cases which only a few GPs judged as unsafe concerned hygiene, the diagnostic process, prevention and communication. The risk factors most frequently judged to constitute a threat to patient safety were a poor doctor-patient relationship, insufficient continuing education on the part of the GP and a patient age over 75 years. Language barriers and polypharmacy also scored high. Deviation from evidence-based guidelines and patient privacy in the reception/waiting room were not perceived as risk factors by most of the GPs. The views of GPs on safety and risk in primary care did not completely match those presented in published papers and policy documents. The GPs in the present study judged a broader range of factors than in previously published research on patient safety in primary care, including a poor doctor-patient relationship, to pose a potential threat to patient safety. Other risk factors such as infection prevention, deviation from guidelines and incident reporting were judged to be less relevant than by policy makers.

Internet of Things Based Combustible Ice Safety Monitoring System Framework

Science.gov (United States)

Sun, Enji

2017-05-01

As the development of human society, more energy is requires to meet the need of human daily lives. New energies play a significant role in solving the problems of serious environmental pollution and resources exhaustion in the present world. Combustible ice is essentially frozen natural gas, which can literally be lit on fire bringing a whole new meaning to fire and ice with less pollutant. This paper analysed the advantages and risks on the uses of combustible ice. By compare to other kinds of alternative energies, the advantages of the uses of combustible ice were concluded. The combustible ice basic physical characters and safety risks were analysed. The developments troubles and key utilizations of combustible ice were predicted in the end. A real-time safety monitoring system framework based on the internet of things (IOT) was built to be applied in the future mining, which provide a brand new way to monitoring the combustible ice mining safety.

Integrated Status and Effectiveness Monitoring Program - Entiat River Snorkel Surveys, 2006-2007.

Energy Technology Data Exchange (ETDEWEB)

Nelle, R.D.

2007-10-01

The USFWS Mid-Columbia River Fishery Resource Office conducted snorkel surveys at 11 sites during the summer 2006 survey period and at 15 sites during fall 2006 and winter 2007 survey periods as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. A total of 39,898 fish from 14 species/genera and an unknown category were enumerated. Chinook salmon were the overall most common fish observed and comprised 19% of fish enumerated followed by mountain whitefish (18%) and rainbow trout (14%). Day and night surveys were conducted during the summer 2006 period (August), while night surveys were conducted during the fall 2006 (October) and winter 2007 (February/March) surveys. This is second annual progress report to Bonneville Power Administration for the snorkel surveys conducted in the Entiat River as related to long-term effectiveness monitoring of restoration programs in this watershed. The objective of this study is to monitor the fish habitat utilization of planned in-stream restoration efforts in the Entiat River by conducting pre- and post-construction snorkel surveys at selected treatment and control sites.

Simultaneous sequential monitoring of efficacy and safety led to masking of effects.

Science.gov (United States)

van Eekelen, Rik; de Hoop, Esther; van der Tweel, Ingeborg

2016-08-01

Usually, sequential designs for clinical trials are applied on the primary (=efficacy) outcome. In practice, other outcomes (e.g., safety) will also be monitored and influence the decision whether to stop a trial early. Implications of simultaneous monitoring on trial decision making are yet unclear. This study examines what happens to the type I error, power, and required sample sizes when one efficacy outcome and one correlated safety outcome are monitored simultaneously using sequential designs. We conducted a simulation study in the framework of a two-arm parallel clinical trial. Interim analyses on two outcomes were performed independently and simultaneously on the same data sets using four sequential monitoring designs, including O'Brien-Fleming and Triangular Test boundaries. Simulations differed in values for correlations and true effect sizes. When an effect was present in both outcomes, competition was introduced, which decreased power (e.g., from 80% to 60%). Futility boundaries for the efficacy outcome reduced overall type I errors as well as power for the safety outcome. Monitoring two correlated outcomes, given that both are essential for early trial termination, leads to masking of true effects. Careful consideration of scenarios must be taken into account when designing sequential trials. Simulation results can help guide trial design. Copyright © 2016 Elsevier Inc. All rights reserved.

Nuclear health and safety

International Nuclear Information System (INIS)

1990-04-01

This report summarizes the responsiveness of DOE and contractors to findings contained in DOE technical safety appraisals and environmental surveys. These appraisals and surveys have been done at DOE facilities and sites to find out the extent of the environmental, safety, and health problems and to prioritize them for corrective action. As of January 1990, DOE computer data showed over 1,700 safety and health problems and almost 1,300 environmental problems. The majority of these problems, however, have not yet been corrected. GAO also looked at the extent to which DOE has developed a computerized tracking system to monitor the status of its environmental, safety, and health problems. GAO found that the computer system lacks important information, such as various field office and independent appraisals. Inclusion of this information would provide a more complete picture of the problems at the site

[Safety monitoring of cell-based medicinal products (CBMPs)].

Science.gov (United States)

Funk, Markus B; Frech, Marion; Spranger, Robert; Keller-Stanislawski, Brigitte

2015-11-01

Cell-based medicinal products (CBMPs), a category of advanced-therapy medicinal products (ATMPs), are authorised for the European market by the European Commission by means of the centralized marketing authorisation. By conforming to the German Medicinal Products Act (Sec. 4b AMG), national authorisation can be granted by the Paul-Ehrlich-Institut in Germany exclusively for ATMPs not based on a routine manufacturing procedure. In both procedures, quality, efficacy, and safety are evaluated and the risk-benefit balance is assessed. For the centralised procedure, mainly controlled clinical trial data must be submitted, whereas the requirements for national procedures could be modified corresponding to the stage of development of the ATMP. After marketing authorization, the marketing authorization/license holder is obligated to report all serious adverse reactions to the competent authority and to provide periodic safety update reports. If necessary, post-authorization safety studies could be imposed. On the basis of these regulatory measures, the safety of advanced therapies can be monitored and improved.

Artificial neural network for research reactor safety status monitoring

International Nuclear Information System (INIS)

Varde, P.V.

2001-01-01

During reactor upset/abnormal conditions, emphasis is placed on plant operator's ability to quickly identify the problem and perform diagnosis and initiate recovery action to ensure safety of the plant. However, the reliability of human action is adversely affected at the time of crisis, due to the time stress and psychological factors. Availability of operational aids capable of monitoring the status of the plant and quickly identifying the deviation from normal operation is expected to significantly improve the operator reliability. Artificial Neural Network (based on Back Propagation Algorithm) has been developed and applied for reactor safety status monitoring, as part of an Operator Support System. ANN has been trained for 14 different plant states using 42 input symptom patterns. Recall tests performed on the ANN show that the system was able to identify the plant state with reasonable accuracy. (author)

Measurement of Food Safety Culture using Survey and Maturity Profiling Tools

OpenAIRE

Jespersen, Lone; Griffiths, Mansel; Maclaurin, Tanya; Chapman, Ben; Wallace, Carol A.

2016-01-01

Organizational culture is defined by dimensions and characteristics that can be used to measure food safety culture in food manufacturing through a food safety maturity model. Maturity models from quality, health care, and information technology have been used since early 1970 and this work presents a novel food safety culture maturity model with five capability areas and food safety pinpointed behaviours specific to functions and levels in a food manufacturing company. A survey tool linked t...

Indicators to monitor NPP safety performance. Working material

International Nuclear Information System (INIS)

1997-01-01

Numerical indicators to monitor safety status and overall safety performance of nuclear power plants (NPPs) are used by operators and some regulators worldwide. During the last few years, the IAEA, through Technical Committee Meetings and Consultants' Meetings has worked on this area. This report presents a framework for nuclear power plant safety performance indicators that was developed during two consultant meetings held at the IAEA headquarters in Vienna in December 1995 and November 1996. Annex 2 on risk based indicators was prepared during a consultants' meeting held in Vienna in July 1996. An additional outcome from these activities, was the recommendation that the IAEA conduce pilot exercises at several nuclear power plants that might be interested to participate, in order to test the validity of the concept and its usefulness. 6 figs

30 CFR 57.5002 - Exposure monitoring.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Exposure monitoring. 57.5002 Section 57.5002 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... monitoring. Dust, gas, mist, and fume surveys shall be conducted as frequently as necessary to determine the...

Comparing NICU teamwork and safety climate across two commonly used survey instruments.

Science.gov (United States)

Profit, Jochen; Lee, Henry C; Sharek, Paul J; Kan, Peggy; Nisbet, Courtney C; Thomas, Eric J; Etchegaray, Jason M; Sexton, Bryan

2016-12-01

Measurement and our understanding of safety culture are still evolving. The objectives of this study were to assess variation in safety and teamwork climate and in the neonatal intensive care unit (NICU) setting, and compare measurement of safety culture scales using two different instruments (Safety Attitudes Questionnaire (SAQ) and Hospital Survey on Patient Safety Culture (HSOPSC)). Cross-sectional survey study of a voluntary sample of 2073 (response rate 62.9%) health professionals in 44 NICUs. To compare survey instruments, we used Spearman's rank correlation coefficients. We also compared similar scales and items across the instruments using t tests and changes in quartile-level performance. We found significant variation across NICUs in safety and teamwork climate scales of SAQ and HSOPSC (pteamwork scales (teamwork climate and teamwork within units) of the two instruments correlated strongly (safety r=0.72, pteamwork r=0.67, p<0.001). However, the means and per cent agreements for all scale scores and even seemingly similar item scores were significantly different. In addition, comparisons of scale score quartiles between the two instruments revealed that half of the NICUs fell into different quartiles when translating between the instruments. Large variation and opportunities for improvement in patient safety culture exist across NICUs. Important systematic differences exist between SAQ and HSOPSC such that these instruments should not be used interchangeably. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Indicators for monitoring of safety operation and condition of nuclear power stations

International Nuclear Information System (INIS)

Manova, D.

2001-01-01

A common goal of all employees in the nuclear power field is safety operation of nuclear power stations. The evaluation and control of NPP safety operation are a part of the elements of safety management. The present report is related only to a part of the total assessment and control of the plant safety operation, namely - the indicator system for monitoring of Kozloduy NPP operation and condition. (author)

A Novel Series Connected Batteries State of High Voltage Safety Monitor System for Electric Vehicle Application

Directory of Open Access Journals (Sweden)

Qiang Jiaxi

2013-01-01

Full Text Available Batteries, as the main or assistant power source of EV (Electric Vehicle, are usually connected in series with high voltage to improve the drivability and energy efficiency. Today, more and more batteries are connected in series with high voltage, if there is any fault in high voltage system (HVS, the consequence is serious and dangerous. Therefore, it is necessary to monitor the electric parameters of HVS to ensure the high voltage safety and protect personal safety. In this study, a high voltage safety monitor system is developed to solve this critical issue. Four key electric parameters including precharge, contact resistance, insulation resistance, and remaining capacity are monitored and analyzed based on the equivalent models presented in this study. The high voltage safety controller which integrates the equivalent models and control strategy is developed. By the help of hardware-in-loop system, the equivalent models integrated in the high voltage safety controller are validated, and the online electric parameters monitor strategy is analyzed and discussed. The test results indicate that the high voltage safety monitor system designed in this paper is suitable for EV application.

A novel series connected batteries state of high voltage safety monitor system for electric vehicle application.

Science.gov (United States)

Jiaxi, Qiang; Lin, Yang; Jianhui, He; Qisheng, Zhou

2013-01-01

Batteries, as the main or assistant power source of EV (Electric Vehicle), are usually connected in series with high voltage to improve the drivability and energy efficiency. Today, more and more batteries are connected in series with high voltage, if there is any fault in high voltage system (HVS), the consequence is serious and dangerous. Therefore, it is necessary to monitor the electric parameters of HVS to ensure the high voltage safety and protect personal safety. In this study, a high voltage safety monitor system is developed to solve this critical issue. Four key electric parameters including precharge, contact resistance, insulation resistance, and remaining capacity are monitored and analyzed based on the equivalent models presented in this study. The high voltage safety controller which integrates the equivalent models and control strategy is developed. By the help of hardware-in-loop system, the equivalent models integrated in the high voltage safety controller are validated, and the online electric parameters monitor strategy is analyzed and discussed. The test results indicate that the high voltage safety monitor system designed in this paper is suitable for EV application.

Understanding of safety monitoring in clinical trials by individuals with CF or their parents: A qualitative analysis.

Science.gov (United States)

Kern-Goldberger, Andrew S; Hessels, Amanda J; Saiman, Lisa; Quittell, Lynne M

2018-03-14

Recruiting both pediatric and adult participants for clinical trials in CF is currently of paramount importance as numerous new therapies are being developed. However, recruitment is challenging as parents of children with CF and adults with CF cite safety concerns as a principal barrier to enrollment. In conjunction with the CF Foundation (CFF) Data Safety Monitoring Board (DSMB), a pilot brochure was developed to inform patients and parents of the multiple levels of safety monitoring; the CFF simultaneously created an infographic representing the safety monitoring process. This study explores the attitudes and beliefs of CF patients and families regarding safety monitoring and clinical trial participation, and elicits feedback regarding the educational materials. Semi-structured interviews were conducted using a pre-tested interview guide and audio-recorded during routine CF clinic visits. Participants included 5 parents of children with CF quotations: attitudes toward clinical trials, safety values, conceptualizing the safety monitoring process, and priorities for delivery of patient education. Participant feedback was used to revise the pilot brochure; text was shortened, unfamiliar words clarified (e.g., "pipeline"), abbreviations eliminated, and redundancy avoided. Qualitative analysis of CF patient and family interviews provided insights into barriers to participation in clinical trials, safety concerns, perspectives on safety monitoring and educational priorities. We plan a multicenter study to determine if the revised brochure reduces knowledge, attitude and practice barriers regarding participation in CF clinical trials. Copyright © 2018 European Cystic Fibrosis Society. Published by Elsevier B.V. All rights reserved.

National Highway Traffic Safety Administration : 1997 customer satisfaction survey

Science.gov (United States)

1998-03-13

In 1995, the National Highway Traffic Safety Administration (NHTSA) conducted its first Customer Satisfaction Survey in response to the requirements of the National Performance Review and Executive Order 12862. An independent research organization, S...

Survey of systems safety analysis methods and their application to nuclear waste management systems

International Nuclear Information System (INIS)

Pelto, P.J.; Winegardner, W.K.; Gallucci, R.H.V.

1981-11-01

This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas for future study

Survey of systems safety analysis methods and their application to nuclear waste management systems

Energy Technology Data Exchange (ETDEWEB)

Pelto, P.J.; Winegardner, W.K.; Gallucci, R.H.V.

1981-11-01

This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas for future study.

Multidisciplinary training program to create new breed of radiation monitor: the health and safety technician

International Nuclear Information System (INIS)

Vance, W.F.

1979-01-01

A multidiscipline training program established to create a new monitor, theHealth and Safety Technician, is described. The training program includes instruction in fire safety, explosives safety, industrial hygiene, industrial safety, health physics, and general safety practices

A survey on reliability and safety analysis techniques of robot systems in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Eom, H S; Kim, J H; Lee, J C; Choi, Y R; Moon, S S

2000-12-01

The reliability and safety analysis techniques was surveyed for the purpose of overall quality improvement of reactor inspection system which is under development in our current project. The contents of this report are : 1. Reliability and safety analysis techniques suvey - Reviewed reliability and safety analysis techniques are generally accepted techniques in many industries including nuclear industry. And we selected a few techniques which are suitable for our robot system. They are falut tree analysis, failure mode and effect analysis, reliability block diagram, markov model, combinational method, and simulation method. 2. Survey on the characteristics of robot systems which are distinguished from other systems and which are important to the analysis. 3. Survey on the nuclear environmental factors which affect the reliability and safety analysis of robot system 4. Collection of the case studies of robot reliability and safety analysis which are performed in foreign countries. The analysis results of this survey will be applied to the improvement of reliability and safety of our robot system and also will be used for the formal qualification and certification of our reactor inspection system.

A survey on reliability and safety analysis techniques of robot systems in nuclear power plants

International Nuclear Information System (INIS)

Eom, H.S.; Kim, J.H.; Lee, J.C.; Choi, Y.R.; Moon, S.S.

2000-12-01

The reliability and safety analysis techniques was surveyed for the purpose of overall quality improvement of reactor inspection system which is under development in our current project. The contents of this report are : 1. Reliability and safety analysis techniques suvey - Reviewed reliability and safety analysis techniques are generally accepted techniques in many industries including nuclear industry. And we selected a few techniques which are suitable for our robot system. They are falut tree analysis, failure mode and effect analysis, reliability block diagram, markov model, combinational method, and simulation method. 2. Survey on the characteristics of robot systems which are distinguished from other systems and which are important to the analysis. 3. Survey on the nuclear environmental factors which affect the reliability and safety analysis of robot system 4. Collection of the case studies of robot reliability and safety analysis which are performed in foreign countries. The analysis results of this survey will be applied to the improvement of reliability and safety of our robot system and also will be used for the formal qualification and certification of our reactor inspection system

An Overview of the NASA Aviation Safety Program Propulsion Health Monitoring Element

Science.gov (United States)

Simon, Donald L.

2000-01-01

The NASA Aviation Safety Program (AvSP) has been initiated with aggressive goals to reduce the civil aviation accident rate, To meet these goals, several technology investment areas have been identified including a sub-element in propulsion health monitoring (PHM). Specific AvSP PHM objectives are to develop and validate propulsion system health monitoring technologies designed to prevent engine malfunctions from occurring in flight, and to mitigate detrimental effects in the event an in-flight malfunction does occur. A review of available propulsion system safety information was conducted to help prioritize PHM areas to focus on under the AvSP. It is noted that when a propulsion malfunction is involved in an aviation accident or incident, it is often a contributing factor rather than the sole cause for the event. Challenging aspects of the development and implementation of PHM technology such as cost, weight, robustness, and reliability are discussed. Specific technology plans are overviewed including vibration diagnostics, model-based controls and diagnostics, advanced instrumentation, and general aviation propulsion system health monitoring technology. Propulsion system health monitoring, in addition to engine design, inspection, maintenance, and pilot training and awareness, is intrinsic to enhancing aviation propulsion system safety.

Assessing the impact of safety monitoring on the efficacy analysis in large Phase III group sequential trials with non-trivial safety event rate.

Science.gov (United States)

Weng, Yanqiu; Palesch, Yuko Y; DeSantis, Stacia M; Zhao, Wenle

2016-01-01

In Phase III clinical trials for life-threatening conditions, some serious but expected adverse events, such as early deaths or congestive heart failure, are often treated as the secondary or co-primary endpoint, and are closely monitored by the Data and Safety Monitoring Committee (DSMC). A naïve group sequential design (GSD) for such a study is to specify univariate statistical boundaries for the efficacy and safety endpoints separately, and then implement the two boundaries during the study, even though the two endpoints are typically correlated. One problem with this naïve design, which has been noted in the statistical literature, is the potential loss of power. In this article, we develop an analytical tool to evaluate this negative impact for trials with non-trivial safety event rates, particularly when the safety monitoring is informal. Using a bivariate binary power function for the GSD with a random-effect component to account for subjective decision-making in safety monitoring, we demonstrate how, under common conditions, the power loss in the naïve design can be substantial. This tool may be helpful to entities such as the DSMCs when they wish to deviate from the prespecified stopping boundaries based on safety measures.

Survey monitoring of environmental radioactivity in Gunsan area

Energy Technology Data Exchange (ETDEWEB)

Kim, Byoung Ho; Ro, Jeong Suk [Kunsan Regional Radioactivity Monitoring Station, Gunsan (Korea, Republic of)

2001-01-15

At Regional Radioactivity Monitoring Station in Kunsan have been measured priodically in 2000 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Artificial radionuclide of {sup 137}Cs in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Jeon-buk, vegetables, fishes, shellfishes, drinking water (total 33ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma isotope for all. No significant Changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzig an artificial nuclide concentration in living environmental sample in Jeon-buk are I fee of radiological contaminants.

Survey monitoring of environmental radioactivity in Gunsan area

Energy Technology Data Exchange (ETDEWEB)

Kim, Byoung Ho; Ro, Jeong Suk [Kunsan Regional Radioactivity Monitoring Station, Gunsan (Korea, Republic of)

2002-12-15

At Regional Radioactivity Monitoring Station in Kunsan have been measured priodically in 2002 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Artificial radionuclide of {sup 137}Cs in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Jeon-buk, vegetables, fishes, shellfishes, drinking water (total 33ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma isotope for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzig an artificial nuclide concentration in living environmental sample in Jeon-buk are fee of radiological contaminants.

Survey monitoring of environmental radioactivity in Gunsan area

International Nuclear Information System (INIS)

Kim, Byoung Ho; Ro, Jeong Suk

2002-12-01

At Regional Radioactivity Monitoring Station in Kunsan have been measured priodically in 2002 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Artificial radionuclide of 137 Cs in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Jeon-buk, vegetables, fishes, shellfishes, drinking water (total 33ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma isotope for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzig an artificial nuclide concentration in living environmental sample in Jeon-buk are fee of radiological contaminants

30 CFR 56.5002 - Exposure monitoring.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Exposure monitoring. 56.5002 Section 56.5002 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Agents Air Quality § 56.5002 Exposure monitoring. Dust, gas, mist, and fume surveys shall be conducted as...

Research oil guidelines for safety review of category 2 waste disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

Safety confirmation items and monitoring items for engineered barriers were compiled, considering the current technical status and monitoring plan for the simulated subsurface disposal and its test facilities. In order to develop the guidelines of the safety review for the disposal of LLW generated from RI facilities and research facilities, technical issues relating toxic substances were surveyed. (author)

Development of radiation safety monitoring system at gamma greenhouse gamma facility

International Nuclear Information System (INIS)

Hairul Nizam Idris; Azimawati Ahmad, Ahmad Zaki Hussain; Ahmad Fairuz Mohd Nasir

2009-01-01

This paper is discussing about installation of radiation safety monitoring system at Gamma Greenhouse Gamma facility, Agrotechnology and Bioscience Division (BAB). This facility actually is an outdoor type irradiation facility, which first in Nuclear Malaysia and the only one in Malaysia. Source Cs-137 (801 Curie) was use as radiation source and it located at the centre of 30 metres diameter size of open irradiation area. The radiation measurement and monitoring system to be equipped in this facility were required the proper equipment and devices, specially purpose for application at outside of building. Research review, literature study and discussion with the equipment manufacturers was being carried out, in effort to identify the best system should be developed. Factors such as tropical climate, environment surrounding and security were considered during selecting the proper system. Since this facility involving with panoramic radiation type, several critical and strategic locations have been fixed with radiation detectors, up to the distance at 200 meter from the radiation source. Apart from that, this developed system also was built for capable to provide the online real-time reading (using internet). In general, it can be summarized that the radiation safety monitoring system for outdoor type irradiation facility was found much different and complex compared to the system for indoor type facility. Keyword: radiation monitoring, radiation safety, Gamma Greenhouse, outdoor irradiation facility, panoramic radiation. (Author)

BARC-risk monitor- a tool for operational safety assessment in nuclear power plants

International Nuclear Information System (INIS)

Vinod, Gopika; Saraf, R.K.; Babar, A.K.; Hadap, Nikhil

2000-12-01

Probabilistic safety assessment has become a key tool as on today to identify and understand nuclear power plant vulnerabilities. As a result of the availability of these PSA studies, there is a desire to use them to enhance plant safety and to operate the nuclear stations in the most efficient manner. Risk monitor is a PC based tool, which computes the real time safety level and assists plant personnel to manage day-to-day activities. Risk monitor is a PC based user friendly software tool used for modification and re-analysis of a nuclear power plant. Operation of risk monitor is based on PSA methods for assisting in day to day applications. Risk monitoring programs can assess the risk profile and are used to optimise the operation of nuclear power plants with respect to a minimum risk level over the operating time. This report presents the background activities of risk monitor, its application areas and also gives the status of such tools in international scenarios. The software is based on the PSA model of Kaiga generating station and would be applicable to similar design configuration. (author)

Radiological safety system based on real-time tritium-in-air monitoring indoor and in effluents

International Nuclear Information System (INIS)

Bidica, Nicolae; Sofalca, Nicolae; Balteanu, Ovidiu-Ioan; Stefan, Ioana-Iuliana

2007-01-01

In this paper we describe an improved real-time tritium monitoring system designed for Heavy Water Detritiation Pilot Plant of National Institute for Cryogenics and Isotopes Separation, Rm. Valcea, Romania. The system consists of three fixed tritium-in-air monitors which measure continuously tritium-in-air concentration (in both species: vapour and gas) in working areas and gaseous effluents. Portable tritium monitors with ionization chamber, and tritium-in-air collector combined with liquid scintillation counter method are also used to supplement fixed instrument measurements. The main functions of tritium monitoring system are: to measure tritium-in air concentration in working areas and gaseous effluents; to alarm the personnel if tritium concentration thresholds are exceeded; to integrate tritium activity released to the environment during a week and to cut off normal ventilation when the activity threshold is exceeded and start the air cleaning system. Now, several especial functions have been added, so that by using appropriate conversion factors, the tritium monitoring system is able to estimate the effective dose rate before starting an activity into the monitored area, during this activity, or soon as the activity was finished. Another new function has been added by coupling tritium-in-air monitoring system with control access system. This is very useful for quick estimation of tritium doses. For routine dosimetric survey, one the internal dose for individuals by measuring tritium in urine is estimated. With all these features our tritium monitoring system is really a safety system for personnel and for environment. (authors)

Reactivity monitoring for safety purposes on the UK prototype fast reactor

International Nuclear Information System (INIS)

Lord, D.J.; Wilkes, D.J.

1987-01-01

The small size and high rating of the liquid metal cooled fast breeder reactor (LMFBR) make the provision of safety related instrumentation for individual subassemblies both difficult and expensive. Global monitoring of the core is thus very attractive. Reactivity monitoring is an important part of such global monitoring. Reactivity monitoring on a short timescale (a few seconds) is used on the UK Prototype Fast Reactor (PFR) as a trip parameter and long-term reactivity monitoring is being developed as a means of providing early warning of slowly developing faults. Results are presented from PFR to demonstrate the capabilities of reactivity monitoring in an operational fast reactor power station. (author)

PTAC driving safety survey results

Energy Technology Data Exchange (ETDEWEB)

Lloyd, E. [Petroleum Technology Alliance Canada, Calgary, AB (Canada)

2005-07-01

The results of a survey conducted by the Petroleum Technology Alliance Canada were presented. The survey identified ways in which companies in the oil and gas industry can reduce the potential for vehicle incidents, as well as improve fleet management techniques. Respondents provided a list of over 60 relevant technologies with high potential for application. Top driving safety challenges included adverse weather and road conditions, as well as driver attitude and awareness. Driver speed and fatigue were also seen as significant challenges, as well as encounters with wildlife and road conditions. Poor site conditions were also identified as a challenge, along with poor hazard recognition training, and lack of experience. A total of 157 representatives responded, whose fleets collectively drive approximately 136,500,000 km per year. The fleets totalled 15,800 vehicles. Respondents' affiliations with the oil and gas industry were included, as well as ownership classifications and company fleet sizes. Total annual fleet kilometers were presented, as well as the number of incidents per company per year, along with the number of respondents' animal strikes per year. tabs, figs.

Analysis of the survey results for the safety culture attitudes of HANARO management division staff

Energy Technology Data Exchange (ETDEWEB)

Lee, M.; Hwang, S. Y.; Lim, I. C.; Kang, T. J.; Choi, H. Y

2003-12-01

This report provides the that analysis results of the surveys on the safety culture attitude and related topics for the HANARO Management Division staff. The survey form consisted of the questionnaire on the safety culture attitude, happiness and life style, drinking habit and traffic safety attitude. The key information drawn from the analysis are as follow; First, the level of safety culture attitude of the staff was confirmed and it was found that the attitude improved when the present analysis results were compared with them for the survey in 1998. Second, the degree of happiness that the staff feel is higher than the average Korean and they enjoy more leisure time than the average Korean. Third, the staff drink more alcohol than the average Korean. Thus, the drinking habit must be improved for the health of the staff. Fourth, the questionnaire of the happiness and the traffic safety attitude should be improved to verify the hypotheses on the relation between them and the safety culture attitude.

Analysis of the survey results for the safety culture attitudes of HANARO management division staff

International Nuclear Information System (INIS)

Lee, M.; Hwang, S. Y.; Lim, I. C.; Kang, T. J.; Choi, H. Y.

2003-12-01

This report provides the that analysis results of the surveys on the safety culture attitude and related topics for the HANARO Management Division staff. The survey form consisted of the questionnaire on the safety culture attitude, happiness and life style, drinking habit and traffic safety attitude. The key information drawn from the analysis are as follow; First, the level of safety culture attitude of the staff was confirmed and it was found that the attitude improved when the present analysis results were compared with them for the survey in 1998. Second, the degree of happiness that the staff feel is higher than the average Korean and they enjoy more leisure time than the average Korean. Third, the staff drink more alcohol than the average Korean. Thus, the drinking habit must be improved for the health of the staff. Fourth, the questionnaire of the happiness and the traffic safety attitude should be improved to verify the hypotheses on the relation between them and the safety culture attitude

Flight physiology training experiences and perspectives: survey of 117 pilots.

Science.gov (United States)

Patrão, Luís; Zorro, Sara; Silva, Jorge; Castelo-Branco, Miguel; Ribeiro, João

2013-06-01

Human factors and awareness of flight physiology play a crucial role in flight safety. Even so, international legislation is vague relative to training requirements in hypoxia and altitude physiology. Based on a previously developed survey, an adapted questionnaire was formulated and released online for Portuguese pilots. Specific questions regarding the need for pilot attention monitoring systems were added to the original survey. There were 117 pilots, 2 of whom were women, who completed the survey. Most of the pilots had a light aviation license and flew in unpressurized cabins at a maximum ceiling of 10,000 ft (3048 m). The majority of the respondents never experienced hypoxic symptoms. In general, most of the individuals agreed with the importance of an introductory hypoxia course without altitude chamber training (ACT) for all pilot populations, and with a pilot monitoring system in order to increase flight safety. Generally, most of the pilots felt that hypoxia education and training for unpressurized aircraft is not extensive enough. However, almost all the respondents were willing to use a flight physiology monitoring system in order to improve flight safety.

Monitoring antimalarial safety and tolerability in clinical trials: A case study from Uganda

Directory of Open Access Journals (Sweden)

Mpimbaza Arthur

2008-06-01

Full Text Available Abstract Background New antimalarial regimens, including artemisinin-based combination therapies (ACTs, have been adopted widely as first-line treatment for uncomplicated malaria. Although these drugs appear to be safe and well-tolerated, experience with their use in Africa is limited and continued assessment of safety is a priority. However, no standardized guidelines for evaluating drug safety and tolerability in malaria studies exist. A system for monitoring adverse events in antimalarial trials conducted in Uganda was developed. Here the reporting system is described, and difficulties faced in analysing and interpreting the safety results are illustrated, using data from the trials. Case description Between 2002 and 2007, eleven randomized, controlled clinical trials were conducted to compare the efficacy, safety, and tolerability of different antimalarial regimens for treatment of uncomplicated malaria in Uganda. The approach to adverse event monitoring was similar in all studies. A total of 5,614 treatments were evaluated in 4,876 patients. Differences in baseline characteristics and patterns of adverse event reporting were noted between the sites, which limited the ability to pool and analyse data. Clinical failure following antimalarial treatment confounded associations between treatment and adverse events that were also common symptoms of malaria, particularly in areas of lower transmission intensity. Discussion and evaluation Despite prospectively evaluating for adverse events, limitations in the monitoring system were identified. New standardized guidelines for monitoring safety and tolerability in antimalarial trials are needed, which should address how to detect events of greatest importance, including serious events, those with a causal relationship to the treatment, those which impact on adherence, and events not previously reported. Conclusion Although the World Health Organization has supported the development of

Survey of factors associated with nurses' perception of patient safety.

Science.gov (United States)

Park, Sun A; Lee, Sui Jin; Choi, Go Un

2011-01-01

To describe the nurses' perception of hospital organization related to cultural issues on the safety of the patient and reporting medical errors. In addition, to identify factors associated with the safety of the patient and the nurse. A survey conducted during December 2008-Jannuary 2009, with 126 nurses using the Korean version of the AHRQ patient safety survey, a self-report 5-point Likert scale. Stata 10.0 was used for descriptive analysis, ANOVA (Analysis of variance) and logistic regression. National Cancer Center in Korea. The means for a working environment related to patient safety was 3.4 (±0.62). The associated factors of duration were at a present hospital, a special area, and direct contact with patients. Among organizational culture factors related to patient safety, the means were 3.81(±0.54) for the boss/manager's perception of patient safety and 3.37(±0.49) for the cooperation/collaboration between units. The frequent number of errors reported by nurses were 1~2(22.2%) times over the past 12 months. For incidence reporting, the items that the 'nurses perceived for communication among clinicians as fair' had a means of 3.23(±0.40) and the 'overall evaluation of patient safety was a good' 3.34(±0.73). The nurses' perception of cooperation and collaboration between units were associated with the direct contact between the patient and the nurse. The frequency of incidence reporting was associated with the duration of working hours at the present hospital and also their work experience. The nurses' perception of hospital environment, organizational culture, and incidence reporting was above average and mostly associated with organizational culture.

Safety regulations regarding to accident monitoring and accident sampling at Russian NPPs with VVER type reactors

International Nuclear Information System (INIS)

Sharafutdinov, Rachet; Lankin, Michail; Kharitonova, Nataliya

2014-01-01

The paper describes a tendency by development of regulatory document requirements related to accident monitoring and accident sampling at Russia's NPPs. Lessons learned from the Fukushima Daiichi accident pointed at the importance and necessary to carry out an additional safety check at Russia's nuclear power plants in the preparedness for management of severe accidents at NPPs. Planned measures for improvement of severe accidents management include development and implementation of the accident instrumentation systems, providing, monitoring, management and storage of information in a severe accident conditions. The draft of Safety Guidelines <monitoring system of nuclear power plants with VVER reactors' prepared by Scientific and Engineering Centre for Nuclear and Radiation Safety (SEC NRS) established the main criteria for accident monitoring instrumentation that can monitor relevant plant parameters in the reactor and inside containment during and after a severe accident in nuclear power plants. Development of these safety guidelines is in line with the recommendations of IAEA Action Plan on Nuclear Safety in response to the Fukushima Daiichi event and recommendations of the IAEA Nuclear Energy series Report <Monitoring Systems for Nuclear Power Plants' (Draft V 2.7). The paper presents the principles, which are used as the basis for selection of plant parameters for accident monitoring and for establishing of accident monitoring instrumentation. The recommendations to the accident sampling system capable to obtain the representative reactor coolant and containment air and fluid samples that support accurate analytical results for the parameters of interest are considered. The radiological and chemistry parameters to be monitored for primary coolant and sump and for containment air are specified. (author)

A Survey of Pilots on the Dissemination of Safety Information

National Research Council Canada - National Science Library

Rakovan, Lori

1999-01-01

A survey was conducted to obtain information from the pilot population on erections of safety-related training currently being offered, its usefulness, and the process through which it might be better...

Work health and safety in cotton ginning industry: a survey of practices in australia

International Nuclear Information System (INIS)

Soomro, N.

2015-01-01

This survey focuses on the WH and S (Work Health and Safety) practices in Australia and relates them with those in Pakistan. It also highlights the planned areas of work required on WH and S in cotton ginning industry of Pakistan. This article is one a series of research studies that will inform a broader approach development. The aim of the survey was to design a standardized health and safety Act for cotton ginning industry of Pakistan and to help ginners meet their due industry obligations under the model WH and S Act. The first component of the research study survey was to review the relevant Australian work and safety model as this provides a framework to protect the health, safety and welfare of all employees at work and of other people who might be affected by the job. The second aspect of the research study survey concerned site visits to cotton gins with the support of Australian Centre for Agricultural Health and Safety, Moree, NSW. During these visits the existing ginning process in terms of WH and S were reviewed. Informal interviews were also conducted with Gin Managers and Ginning Experts regarding WH and S in the Australian cotton ginning industry. (author)

Safety practices, perceptions, and behaviors in radiation oncology: A national survey of radiation therapists.

Science.gov (United States)

Woodhouse, Kristina Demas; Hashemi, David; Betcher, Kathryn; Doucette, Abigail; Weaver, Allison; Monzon, Brian; Rosenthal, Seth A; Vapiwala, Neha

Radiation therapy is complex and demands high vigilance and precise coordination. Radiation therapists (RTTs) directly deliver radiation and are often the first to discover an error. Yet, few studies have examined the practices of RTTs regarding patient safety. We conducted a national survey to explore the perspectives of RTTs related to quality and safety. In 2016, an electronic survey was sent to a random sample of 1500 RTTs in the United States. The survey assessed department safety, error reporting, safety knowledge, and culture. Questions were multiple choice or recorded on a Likert scale. Results were summarized using descriptive statistics and analyzed using multivariate logistic regression. A total of 702 RTTs from 49 states (47% response rate) completed the survey. Respondents represented a broad distribution across practice settings. Most RTTs rated department patient safety as excellent (61%) or very good (32%), especially if they had an incident learning system (ILS) (odds ratio, 2.0). Only 21% reported using an ILS despite 58% reporting an accessible ILS in their department. RTTs felt errors were most likely to occur with longer shifts and poor multidisciplinary communication; 40% reported that burnout and anxiety negatively affected their ability to deliver care. Workplace bullying was also reported among 17%. Overall, there was interest (62%) in improving knowledge in patient safety. Although most RTTs reported excellent safety cultures within their facilities, overall, there was limited access to and utilization of ILSs by RTTs. Workplace issues identified may also represent barriers to delivering quality care. RTTs were also interested in additional resources regarding quality and safety. These results will further enhance safety initiatives and inform future innovative educational efforts in radiation oncology. Copyright © 2017 American Society for Radiation Oncology. Published by Elsevier Inc. All rights reserved.

Concept for creating program-technical complex of safety monitoring with system of safety parameters presentation functions on the basis of routine WWER-1000 systems

International Nuclear Information System (INIS)

Dunaev, V.G.; Tarasov, M. V.; Povarov, P.V.

2005-01-01

Prerequisites of creating the software-hardware complex for reactor safety monitoring on the Volgodonsk NPP are analyzed and generalized. The concept of this complex is based on functions of the safety parameters presentation system. It will serve as an interface between operator and technological process and give to operator a possibility to estimate quickly the state of the safety of the nuclear power unit. The complex will be created on the basis of routine reactor monitoring and control systems intended for the WWER-1000 reactor. In addition to existing soft- and hard-wares for reactor monitoring and for analysis of technological archive, it is proposed to create and connect in parallel the new software-hardware complex which ensures calculation and presentation of generalized factors of reactor safety [ru

Monitoring consumer confidence in food safety: an exploratory study

NARCIS (Netherlands)

Jonge, de J.; Frewer, L.J.; Trijp, van J.C.M.; Renes, R.J.; Wit, de W.; Timmers, J.C.M.

2004-01-01

Abstract: In response to the potential for negative economic and societal effects resulting from a low level of consumer confidence in food safety, it is important to know how confidence is potentially influenced by external events. The aim of this article is to describe the development of a monitor

Uncertain added value of Global Trigger Tool for monitoring of patient safety in cancer care

DEFF Research Database (Denmark)

Lipczak, Henriette; Neckelmann, Kirsten; Steding-Jessen, Marianne

2011-01-01

Monitoring patient safety is a challenging task. The lack of a golden standard has contributed to the recommendation and introduction of several methods. In 2000 the Danish Lung Cancer Registry (DLCR) was established to monitor the clinical management of lung cancer. In 2008 the Global Trigger Tool...... (GTT) was recommended in Denmark as a tool for the monitoring of patient safety. Ideally, the recommendation of a new tool should be preceded by a critical assessment of its added value....

Design of safety monitor system for operation sintering furnace ME-06

International Nuclear Information System (INIS)

Sugeng Rianto; Triarjo; Djoko Kisworo; Agus Sartono

2013-01-01

Design of safety monitoring system for safety operation of sinter furnace ME-06 has been done. Parameters monitored during this operation include: temperature, gas pressure, flow rate of gas, voltage and current furnace. For sintering furnace temperature system that monitored were the temperature of the furnace temperature, the temperature of the cooling water system inlet and outlet, temperature of flow hydrogen gas inlet and outlet. For pressure system and flow rate gas sinter furnace which monitored the pressure and flow rate of hydrogen gas inlet and outlet. The system also monitors current and voltage applied to the sinter furnace heating system. Monitor system hardware consists of: the system temperature sensor, pressure, rate and data acquisition systems. While software systems using the labview driver interface that connects the hard and software systems. Function test results during sintering operation for setting the temperature 1700 °C sintering temperature increases the ramp function by 250 °C/hour average measurements obtained when the sintering time 1707.016 °C with a standard deviation of 0.38 °C. The maximum temperature of the hydrogen gas temperature 35.4 °C. The maximum temperature of the cooling water system 27.4 °C. The maximum pressure of 1,911 bar Gas Inlet and outlet of 0,051 bar. Maximum inlet gas flow 12.996 L / min and outlet 14.086 L / min. (author)

Analysis of an Unmanned Aerial Vehicle Monitoring System for Resurveying of Shipping Routes

Directory of Open Access Journals (Sweden)

Urbahs Aleksandrs

2016-12-01

Full Text Available The paper gives brief description of the conventional and innovative hydrography survey methods and constraints connected with the realization. Proposed hydrographic survey system based on the use of Unmanned Aerial and Maritime systems provides functionality to conduct hydrographic measurements and environment monitoring. System can be easily adapted to fulfil marine safety and security operations, e.g. intrusion threat monitoring, hazardous pollutions monitoring and prevention operations, icing conditions monitoring.

Survey monitoring of environmental radioactivity in Jeju area

Energy Technology Data Exchange (ETDEWEB)

U, Zang Kual; Kang, Tae Woo; Park, Won Pyo [Jeju National Univ., Jeju (Korea, Republic of)

2003-12-15

The project is carried out to monitor the change of environmental radioactivity in Jeju, and to provide a systematic data for radiation monitoring and counter measurement at a radiological emergency situation. Also the survey of natural environmental radioactivities in the samples was conducted to make the reliable data base for evaluation of internal exposure and environmental contamination of radiation. This report contains the data of gamma exposure rates and radioactivities of airborne dust, fallout, precipitation and tap water which were analyzed periodically by Jeju Regional Monitoring Station in 2002. Also it contains the data of natural radioactivity levels of food stuff such as agricultural and marine products, including drinking waters.

Survey monitoring of environmental radioactivity in Jeju area

Energy Technology Data Exchange (ETDEWEB)

U, Z. K.; Oh, S. H. [Jeju National Univ., Jeju (Korea, Republic of)

1998-01-15

The project is carried out to monitor the change of environmental radioactivity in Jeju, and to provide a systematic data for radiation monitoring and counter measurement at a radiological emergency situation. Also the survey of natural environmental radioactivities in the samples was conducted to make the reliable data base for evaluation of internal exposure and environmental contamination of radiation. This report contains the data of gamma exposure rates and radioactivities of airborne dust, fallout, precipitation and tap water which were analyzed periodically by Jeju Regional Monitoring Station in 1997. Also it contains the data of natural radioactivity levels of food stuff such as agricultural and marine products, including drinking waters.

Survey monitoring of environmental radioactivity in Jeju area

Energy Technology Data Exchange (ETDEWEB)

U, Zang Kual; Kang, Tae Woo; Park, Won Pyo [Jeju National Univ., Jeju (Korea, Republic of)

2002-12-15

The project is carried out to monitor the change of environmental radioactivity in Jeju, and to provide a systematic data for radiation monitoring and counter measurement at a radiological emergency situation. Also the survey of natural environmental radioactivities in the samples was conducted to make the reliable data base for evaluation of internal exposure and environmental contamination of radiation. This report contains the data of gamma exposure rates and radioactivities of airborne dust, fallout, precipitation and tap water which were analyzed periodically by Jeju Regional Monitoring Station in 2001. Also it contains the data of natural radioactivity levels of food stuff such as agricultural and marine products, including drinking waters.

Guidance on the implementation of a risk based safety performance monitoring system for nuclear power plants

International Nuclear Information System (INIS)

Sewell, R.T.; Kuritzky, A.S.; Khatib-Rahbar, M.

1997-05-01

The principal objective of the present study is to review and evaluate existing Performance Indicator (PI) monitoring programs, and to develop and demonstrate an overall PSA-based methodology and framework for the monitoring and use of risk-based PIs and SIs (Safety Indicator), that would enable: Identification of trends and patterns in safety performance at a specific plant and a population of plants; Assessment of the significance of the trends and patterns; Identification of precursors of accident sequences and safety reductions; Identification of the most critical functional areas of concern, especially as they relate to a defense-in-depth safety philosophy; Comparison of safety performance trends at a plant with those at comparable plants; Incorporation of the PIs and SIs into a risk- and performance-based decision process. To support the overall project objective, it is important that information needs and data collection procedures are clearly outlined. Of key significance in this regard is the premise that a performance monitoring system should not be burdened by an excessive number of low-level PIs that may have only a peripheral relationship to safety. Other supporting objectives of the study include: To identify and discuss other issues pertaining to the practical implementation of a safety performance monitoring system (outlining the databases and algorithms needed); and to demonstrate implementation of the preliminary guidance for monitoring and use of the selected set of PIs and SIs, within the proposed framework, via application to the operating history of a NPP having a PSA and readily available event data

Voices of nuclear-power monitors in fiscal 1981

International Nuclear Information System (INIS)

1983-01-01

The system of ''nuclear-power monitors'', started in fiscal 1977, is for the purpose of hearing the opinions of general people on nuclear power development and utilization and reflecting the results to the governmental nuclear power administration. The number of monitors in fiscal 1981 is a total of 504. The results in the fiscal year are described: (1) Questionnaire survey: The survey was made from March 10 to 25, 1982. Of the total, 355 (70.4%) answered the questions concerning the following matters: the future of energy, the development of nuclear power, the administration of nuclear power safety, and nuclear power public relations. (2) Voices (opinion) sent by the monitors: Of the total 150 items sent from September, 1981, to March, 1982, 48 concerned public relations, 26 were about the development and utilization and 25 were about the safety. (Mori, K.)

The durban beach monitoring program: simple surveys speak volumes

CSIR Research Space (South Africa)

de Wet, p

2010-10-01

Full Text Available program: simple surveys speak volumes Pierre de Wet, Andrew Mather, Andr? Theron SAEON summit, 6 October 2010 ? CSIR 2010 Slide 1www.csir.co.za Outline ? Background / History ? Monitoring area circle6 Examples of survey data & trends circle6...) and near-shore deposition cf. classical understanding / scheme ? CSIR 2010 Slide 6 ? id. areas vulnerable to erosion ? effect of replenishment rates / locations visible Beach survey data s h o r e l i n e p o s i t i o n [ m...

Monitoring road safety development at regional level: A case study in the ASEAN region.

Science.gov (United States)

Chen, Faan; Wang, Jianjun; Wu, Jiaorong; Chen, Xiaohong; Zegras, P Christopher

2017-09-01

Persistent monitoring of progress, evaluating the results of interventions and recalibrating to achieve continuous improvement over time is widely recognized as being crucial towards the successful development of road safety. In the ASEAN (Association of Southeast Asian Nations) region there is a lack of well-resourced teams that contain multidisciplinary safety professionals, and specialists in individual countries, who are able to carry out this work effectively. In this context, not only must the monitoring framework be effective, it must also be easy to use and adapt. This paper provides a case study that can be easily reproduced; based on an updated and refined Road Safety Development Index (RSDI), by means of the RSR (Rank-sum ratio)-based model, for monitoring/reporting road safety development at regional level. The case study was focused on the road safety achievements in eleven Southeast Asian countries; identifying the areas of poor performance, potential problems and delays. These countries are finally grouped into several classes based on an overview of their progress and achievements regarding to road safety. The results allow the policymakers to better understand their own road safety progress toward their desired impact; more importantly, these results enable necessary interventions to be made in a quick and timely manner. Keeping action plans on schedule if things are not progressing as desired. This would avoid 'reinventing the wheel' and trial and error approaches to road safety, making the implementation of action plans more effective. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Study on the Estimation Method of Risk Based Area for Jetty Safety Monitoring

Directory of Open Access Journals (Sweden)

Byeong-Wook Nam

2015-09-01

Full Text Available Recently, the importance of safety-monitoring systems was highlighted by the unprecedented collision between a ship and a jetty in Yeosu. Accordingly, in this study, we introduce the concept of risk based area and develop a methodology for a jetty safety-monitoring system. By calculating the risk based areas for a ship and a jetty, the risk of collision was evaluated. To calculate the risk based areas, we employed an automatic identification system for the ship, stopping-distance equations, and the regulation velocity near the jetty. In this paper, we suggest a risk calculation method for jetty safety monitoring that can determine the collision probability in real time and predict collisions using the amount of overlap between the two calculated risk based areas. A test was conducted at a jetty control center at GS Caltex, and the effectiveness of the proposed risk calculation method was verified. The method is currently applied to the jetty-monitoring system at GS Caltex in Yeosu for the prevention of collisions.

[Adaptation of the Medical Office Survey on Patient Safety Culture (MOSPSC) tool].

Science.gov (United States)

Silvestre-Busto, C; Torijano-Casalengua, M L; Olivera-Cañadas, G; Astier-Peña, M P; Maderuelo-Fernández, J A; Rubio-Aguado, E A

2015-01-01

To adapt the Medical Office Survey on Patient Safety Culture (MOSPSC) Excel(®) tool for its use by Primary Care Teams of the Spanish National Public Health System. The process of translation and adaptation of MOSPSC from the Agency for Healthcare and Research in Quality (AHRQ) was performed in five steps: Original version translation, Conceptual equivalence evaluation, Acceptability and viability assessment, Content validity and Questionnaire test and response analysis, and psychometric properties assessment. After confirming MOSPSC as a valid, reliable, consistent and useful tool for assessing patient safety culture in our setting, an Excel(®) worksheet was translated and adapted in the same way. It was decided to develop a tool to analyze the "Spanish survey" and to keep it linked to the "Original version" tool. The "Spanish survey" comparison data are those obtained in a 2011 nationwide Spanish survey, while the "Original version" comparison data are those provided by the AHRQ in 2012. The translated and adapted tool and the analysis of the results from a 2011 nationwide Spanish survey are available on the website of the Ministry of Health, Social Services and Equality. It allows the questions which are decisive in the different dimensions to be determined, and it provides a comparison of the results with graphical representation. Translation and adaptation of this tool enables a patient safety culture in Primary Care in Spain to be more effectively applied. Copyright © 2014 SECA. Published by Elsevier Espana. All rights reserved.

49 CFR 385.333 - What happens at the end of the 18-month safety monitoring period?

Science.gov (United States)

2010-10-01

... SAFETY REGULATIONS SAFETY FITNESS PROCEDURES New Entrant Safety Assurance Program § 385.333 What happens at the end of the 18-month safety monitoring period? (a) If a safety audit has been performed within... the same basis as any other carrier. (d) If a safety audit or compliance review has not been performed...

Safety KPIs - Monitoring of safety performance

Directory of Open Access Journals (Sweden)

Andrej Lališ

2014-09-01

Full Text Available This paper aims to provide brief overview of aviation safety development focusing on modern trends represented by implementation of Safety Key Performance Indicators. Even though aviation is perceived as safe means of transport, it is still struggling with its complexity given by long-term growth and robustness which it has reached today. Thus nowadays safety issues are much more complex and harder to handle than ever before. We are more and more concerned about organizational factors and control mechanisms which have potential to further increase level of aviation safety. Within this paper we will not only introduce the concept of Key Performance Indicators in area of aviation safety as an efficient control mechanism, but also analyse available legislation and documentation. Finally we will propose complex set of indicators which could be applied to Czech Air Navigation Service Provider.

Use of the Safety Monitor in operational decision-making at a nuclear generating facility

International Nuclear Information System (INIS)

Chien, Shan H.; Hook, Thomas G.; Lee, Roger J.

1998-01-01

The utilization of Safety Monitor at a nuclear generating facility in 1994 revolutionized the way US nuclear power plants manage configuration risks. At Southern California Edison (SCE) Company's San Onofre Nuclear Generating Station, it transformed probabilistic risk assessment (PRA) from a retrospective tool for understanding past risk into a prospective tool for controlling future risk. Since that time, many other nuclear utilities have taken aggressive steps in using PRA better to understand and manage risks associated with plant operation and maintenance. These utilities have employed a variety of methods ranging from systems similar to San Onofre's Safety Monitor to systems dramatically different in both technology and philosophy. In the development and use of its Safety Monitor, SCE has been guided by two philosophical goals: (1) maximize the objectivity of PRA-informed decision-making relative to managing configuration risks, and (2) ensure that risks are managed conservatively

Radiological safety system based on real-time tritium-in-air monitoring indoors and in effluents

International Nuclear Information System (INIS)

Bidica, N.; Sofalca, N; Balteanu, O.; Srefan, I.

2006-01-01

Exposure to tritium is an important health hazard in any tritium processing facility so that implementing a real-time tritium monitoring system is necessary for its operation in safety conditions. The tritium processing facility operators need to be informed at any time about the in-air tritium concentration indoors or in the stack effluents, in order to detect immediately any leaks in tritium containments, or any releases inside the buildings or to the environment. This information is very important for adopting if necessary protection measures and correcting actions as quickly as possible. In this paper we describe an improved real-time tritium monitoring system designed for the Heavy Water Detritiation Pilot Plant of National Institute for Cryogenics and Isotopes Separation, Rm. Valcea, Romania. The design of the Radiological Safety System implemented for the ICIT Water Detritiation Pilot Plant is intended to provide the maximum safety level based on the ALARA concept. The main functions of tritium monitoring system are: - monitoring the working areas and gaseous effluents by determination of the tritium-in-air activity concentration; - local and remote data display; - assessing of environment dose equivalent rates and dose equivalents in the working environment (for personnel exposure control and work planning); - assessing the total tritium activity released to the environment through ventilation exhaust stack; - safety functions, i.e., local and remote, locking/unlocking personnel access, process shut-down in emergency conditions and start of the air cleaning systems. With all these features our tritium monitoring system is really a safety system adequate for personnel and environmental protection. (authors)

Monitoring of patients treated with lithium for bipolar disorder: an international survey.

Science.gov (United States)

Nederlof, M; Heerdink, E R; Egberts, A C G; Wilting, I; Stoker, L J; Hoekstra, R; Kupka, R W

2018-04-14

Adequate monitoring of patients using lithium is needed for optimal dosing and for early identification of patients with (potential) ADEs. The objective was to internationally assess how health care professionals monitor patients treated with lithium for bipolar disorder. Using networks of various professional organizations, an anonymous online survey was conducted among health care professionals prescribing lithium. Target lithium serum levels and frequency of monitoring was assessed together with monitoring of physical and laboratory parameters. Reasons to and not to monitor and use of guidelines and institutional protocols, and local monitoring systems were investigated. The survey was completed by 117 health care professionals incorporating responses from twenty-four countries. All prescribers reported to monitor lithium serum levels on a regular basis, with varying target ranges. Almost all (> 97%) monitored thyroid and renal function before start and during maintenance treatment. Reported monitoring of other laboratory and physical parameters was variable. The majority of respondents (74%) used guidelines or institutional protocols for monitoring. In general, the prescriber was responsible for monitoring, had to request every monitoring parameter separately and only a minority of patients was automatically invited. Lithium serum levels, renal and thyroid function were monitored by (almost) all physicians. However, there was considerable variation in other monitoring parameters. Our results help to understand why prescribers of lithium monitor patients and what their main reasons are not to monitor patients using lithium.

Automatic crack detection and classification method for subway tunnel safety monitoring.

Science.gov (United States)

Zhang, Wenyu; Zhang, Zhenjiang; Qi, Dapeng; Liu, Yun

2014-10-16

Cracks are an important indicator reflecting the safety status of infrastructures. This paper presents an automatic crack detection and classification methodology for subway tunnel safety monitoring. With the application of high-speed complementary metal-oxide-semiconductor (CMOS) industrial cameras, the tunnel surface can be captured and stored in digital images. In a next step, the local dark regions with potential crack defects are segmented from the original gray-scale images by utilizing morphological image processing techniques and thresholding operations. In the feature extraction process, we present a distance histogram based shape descriptor that effectively describes the spatial shape difference between cracks and other irrelevant objects. Along with other features, the classification results successfully remove over 90% misidentified objects. Also, compared with the original gray-scale images, over 90% of the crack length is preserved in the last output binary images. The proposed approach was tested on the safety monitoring for Beijing Subway Line 1. The experimental results revealed the rules of parameter settings and also proved that the proposed approach is effective and efficient for automatic crack detection and classification.

Automatic Crack Detection and Classification Method for Subway Tunnel Safety Monitoring

Directory of Open Access Journals (Sweden)

Wenyu Zhang

2014-10-01

Full Text Available Cracks are an important indicator reflecting the safety status of infrastructures. This paper presents an automatic crack detection and classification methodology for subway tunnel safety monitoring. With the application of high-speed complementary metal-oxide-semiconductor (CMOS industrial cameras, the tunnel surface can be captured and stored in digital images. In a next step, the local dark regions with potential crack defects are segmented from the original gray-scale images by utilizing morphological image processing techniques and thresholding operations. In the feature extraction process, we present a distance histogram based shape descriptor that effectively describes the spatial shape difference between cracks and other irrelevant objects. Along with other features, the classification results successfully remove over 90% misidentified objects. Also, compared with the original gray-scale images, over 90% of the crack length is preserved in the last output binary images. The proposed approach was tested on the safety monitoring for Beijing Subway Line 1. The experimental results revealed the rules of parameter settings and also proved that the proposed approach is effective and efficient for automatic crack detection and classification.

Toward an integrated system concept for monitoring and evaluation of safety culture

International Nuclear Information System (INIS)

Makino, Maomi; Sakaue, Takeharu

2004-01-01

The concept of ''nuclear safety culture'' has been advocated and has been much discussed internationally by INSAG (The International Nuclear Safety Advisory Group) under IAEA (the International Atomic Energy Agency) and other institutions since Chernobyl accident. On the safety front, Japan had maintained an excellent track record in nuclear power operations throughout the 1990s. However, there have been a series of new type of problems strongly implying degradation of safety culture, e.g., Monju accident, fire and explosion accident at an Asphalt Solidification Process Facility at Tokai, falsification of annealing data at nuclear power plants (NPP), another data falsification for transport cask of spent fuel and JCO criticality accident. Then the TEPCO (Tokyo Electric Power Company) issue was revealed in 2002. Triggered by this issue, the Nuclear and Industrial Safety Agency (NISA) has been implementing a variety of improvements, one of which was the establishment of a study group in 2003, which invited experts from other fields as well as from nuclear-related industries, to study on how to implement safety culture sufficiently and possible recommendations. Subjects such as the followings piled in the study report will indicate leading keys in case it is going to realize such efforts: ''Foundation of safety culture is a quality management'' and ''Realistic and scientific technique is necessary for the evaluation of safety culture''. In order to respond to these requests, JNES have been advancing the development toward an Integrated System Concept for Monitoring and Evaluation of Safety Culture. This paper describes the outline of the study results reported by the study group and then introduces one of subsystems, SCEST, structuring the integrated system concept for Monitoring and Evaluation of Safety Culture. (author)

Agricultural Health and Safety Survey in Friuli Venezia Giulia

Directory of Open Access Journals (Sweden)

Sirio Rossano Secondo Cividino

2018-01-01

Full Text Available The work in the agricultural sector has taken on a fundamental role in the last decades, due to the still too high rate of fatal injuries, workplace accidents, and dangerous occurrences reported each year. The average old age of agricultural machinery is one of the main issues at stake in Italy. Numerous safety problems stem from that; therefore, two surveys were conducted in two different periods, on current levels of work safety in agriculture in relation to agricultural machinery’s age and efficiency, and to show the levels of actual implementation of the Italian legislation on safety and health at work in the agricultural sector. The surveys were carried out, considering a sample of 161 farms located in the region Friuli Venezia Giulia (North-East of Italy. The research highlights the most significant difficulties the sample of farms considered have in enforcing the law. One hand, sanitary surveillance and workers’ information and training represent the main deficiencies and weakest points in family farms. Moreover, family farms do not generally provide the proper documentation concerning health and safety at workplaces, when they award the contract to other companies. On the other hand, lack of maintenance program for machinery and equipment, and of emergency plans and participation of workers’ health and safety representative, are the most common issues in farms with employees. Several difficulties are also evident in planning workers’ training programs. Furthermore, the company physician’s task is often limited to medical controls, so that he is not involved in risk assessment and training. Interviews in heterogeneous samples of farms have shown meaningful outcomes, which have subsequently been used to implement new databases and guidelines for Health and Safety Experts and courses in the field of Work Safety in agriculture. In conclusion, although the legislation making training courses for tractor operators and tractor

Northern Mariana Islands Marine Monitoring Team Reef Flat Surveys

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Commonwealth of the Northern Mariana Islands' (CNMI) interagency marine monitoring team conducts surveys on reef flat areas on the islands of Saipan, Tinian and...

Construction safety monitoring based on the project's characteristic with fuzzy logic approach

Science.gov (United States)

Winanda, Lila Ayu Ratna; Adi, Trijoko Wahyu; Anwar, Nadjadji; Wahyuni, Febriana Santi

2017-11-01

Construction workers accident is the highest number compared with other industries and falls are the main cause of fatal and serious injuries in high rise projects. Generally, construction workers accidents are caused by unsafe act and unsafe condition that can occur separately or together, thus a safety monitoring system based on influencing factors is needed to achieve zero accident in construction industry. The dynamic characteristic in construction causes high mobility for workers while doing the task, so it requires a continuously monitoring system to detect unsafe condition and to protect workers from potential hazards. In accordance with the unique nature of project, fuzzy logic approach is one of the appropriate methods for workers safety monitoring on site. In this study, the focus of discussion is based on the characteristic of construction projects in analyzing "potential hazard" and the "protection planning" to be used in accident prevention. The data have been collected from literature review, expert opinion and institution of safety and health. This data used to determine hazard identification. Then, an application model is created using Delphi programming. The process in fuzzy is divided into fuzzification, inference and defuzzification, according to the data collection. Then, the input and final output data are given back to the expert for assessment as a validation of application model. The result of the study showed that the potential hazard of construction workers accident could be analysed based on characteristic of project and protection system on site and fuzzy logic approach can be used for construction workers accident analysis. Based on case study and the feedback assessment from expert, it showed that the application model can be used as one of the safety monitoring tools.

STRUCTURAL MONITORING WITH GEODETIC SURVEY OF QUADRIFOGLIO CONDOMINIUM (LECCE

Directory of Open Access Journals (Sweden)

D. Costantino

2014-01-01

Full Text Available Monitoring buildings for moving elements has been always a problem of great importance for their conservation and preservation, as well as for risk mitigation. In particular, topographic surveying allows, through the use of the principles and instruments of the geodetic survey, to control moving points which have been identified and measured. In this study case, twelve survey campaigns were done for monitoring a building located in the city of Lecce. The condominium was built five years ago on an old quarry filled with debris to allow construction. Later in time, obviously, cracks started to appear on walls within the property, and for this legal actions were taken. The survey schema adopted has been that of triangulation/trilateration, from two vertices with known coordinates. With this methodologies four cornerstones have been identified, established with forced centering on pillars with anchor plates, connected to same number of framework points, considered stable. From these, 23 control points located on the structure with rotating prisms anchored at the same manner have been surveyed. The elaboration has been carried out by generating redundancy of the measures and compensating the values with least mean squares. The results obtained by the activity of survey and elaboration have confirmed the existence of ongoing phenomena. The causes that have generated the phenomenon have been, subsequently, investigated and have been considered attributable to the existence of a sewer pipeline and a water pipeline not properly put in place and consequently broke down due to the geological characteristics of the site.

Radiation safety assessment and development of environmental radiation monitoring technology

CERN Document Server

Choi, B H; Kim, S G

2002-01-01

The Periodic Safety Review(PSR) of the existing nuclear power plants is required every ten years according to the recently revised atomic energy acts. The PSR of Kori unit 1 and Wolsong unit 1 that have been operating more than ten years is ongoing to comply the regulations. This research project started to develop the techniques necessary for the PSR. The project developed the following four techniques at the first stage for the environmental assessment of the existing plants. 1) Establishment of the assessment technology for contamination and accumulation trends of radionuclides, 2) alarm point setting of environmental radiation monitoring system, 3) Development of Radiation Safety Evaluation Factor for Korean NPP, and 4) the evaluation of radiation monitoring system performance and set-up of alarm/warn set point. A dynamic compartment model to derive a relationship between the release rates of gas phase radionuclides and the concentrations in the environmental samples. The model was validated by comparing ...

Evaluation of a survey tool to measure safety climate in Australian hospital pharmacy staff.

Science.gov (United States)

Walpola, Ramesh L; Chen, Timothy F; Fois, Romano A; Ashcroft, Darren M; Lalor, Daniel J

Safety climate evaluation is increasingly used by hospitals as part of quality improvement initiatives. Consequently, it is necessary to have validated tools to measure changes. To evaluate the construct validity and internal consistency of a survey tool to measure Australian hospital pharmacy patient safety climate. A 42 item cross-sectional survey was used to evaluate the patient safety climate of 607 Australian hospital pharmacy staff. Survey responses were initially mapped to the factor structure previously identified in European community pharmacy. However, as the data did not adequately fit the community pharmacy model, participants were randomly split into two groups with exploratory factor analysis performed on the first group (n = 302) and confirmatory factor analyses performed on the second group (n = 305). Following exploratory factor analysis (59.3% variance explained) and confirmatory factor analysis, a 6-factor model containing 28 items was obtained with satisfactory model fit (χ 2 (335) = 664.61 p  0.643) and model nesting between the groups (Δχ 2 (22) = 30.87, p = 0.10). Three factors (blame culture, organisational learning and working conditions) were similar to those identified in European community pharmacy and labelled identically. Three additional factors (preoccupation with improvement; comfort to question authority; and safety issues being swept under the carpet) highlight hierarchical issues present in hospital settings. This study has demonstrated the validity of a survey to evaluate patient safety climate of Australian hospital pharmacy staff. Importantly, this validated factor structure may be used to evaluate changes in safety climate over time. Copyright © 2016 Elsevier Inc. All rights reserved.

Study on Semi-Parametric Statistical Model of Safety Monitoring of Cracks in Concrete Dams

Directory of Open Access Journals (Sweden)

Chongshi Gu

2013-01-01

Full Text Available Cracks are one of the hidden dangers in concrete dams. The study on safety monitoring models of concrete dam cracks has always been difficult. Using the parametric statistical model of safety monitoring of cracks in concrete dams, with the help of the semi-parametric statistical theory, and considering the abnormal behaviors of these cracks, the semi-parametric statistical model of safety monitoring of concrete dam cracks is established to overcome the limitation of the parametric model in expressing the objective model. Previous projects show that the semi-parametric statistical model has a stronger fitting effect and has a better explanation for cracks in concrete dams than the parametric statistical model. However, when used for forecast, the forecast capability of the semi-parametric statistical model is equivalent to that of the parametric statistical model. The modeling of the semi-parametric statistical model is simple, has a reasonable principle, and has a strong practicality, with a good application prospect in the actual project.

Survey monitoring of environmental radioactivity in Jeju area

Energy Technology Data Exchange (ETDEWEB)

U, Zang Kual; Kang, Tae Woo [Jeju National Univ., Jeju (Korea, Republic of)

2000-12-15

The project is carried out to monitor the change of environmental radioactivity in Jeju, and to provide a systematic data for radiation monitoring and counter measurement at a radiological emergency situation. Also the survey of natural environmental radioactivities in the samples was conducted to make the reliable data base for evaluation of internal exposure and environmental contamination of radiation. This report contains the data of gamma exposure rates and radioactivities of airborne dust, fallout, precipitation and tap water which were analyzed periodically by Jeju Regional Monitoring Station in 2000. Also it contains the data of natural radioactivity levels of food stuff such as agricultural and marine products, including drinking waters. There was no significant difference in environmental radioactivities between 1999 and 2000.

School Safety, Severe Disciplinary Actions, and School Characteristics: A Secondary Analysis of the School Survey on Crime and Safety

Science.gov (United States)

Han, Seunghee; Akiba, Motoko

2011-01-01

On the basis of a secondary analysis of survey data collected from 1,872 secondary school principals in the 2005-2006 School Survey on Crime and Safety, we examined the frequency of and reasons for severe disciplinary actions and the relationship between school characteristics and severe disciplinary actions. We found that severe disciplinary…

Patient safety in practical nurses' education: A cross-sectional survey of newly registered practical nurses in Canada.

Science.gov (United States)

VanDenKerkhof, Elizabeth; Sears, Nancy; Edge, Dana S; Tregunno, Deborah; Ginsburg, Liane

2017-04-01

Practical nurses have experienced an increasing scope of practice, including an expectation to care for complex patients and function on interdisciplinary teams. Little is known about the degree to which patient safety principles are addressed in practical nursing education. To examine self-reported patient safety competencies of practical nurses. A cross-sectional online survey (July 2014) and face-to-face interviews (June 2015). Ontario, Canada. Survey participants were practical nurses newly registered with the College of Nurses of Ontario between January 2012 and December 2013. Interview participants were faculty and students in a practical nursing program in Ontario. Survey respondents completed the Health Professional Education in Patient Safety Survey online. Self-reported competencies in various patient safety domains were compared between classroom and clinical settings. Faculty members were interviewed about educational preparation of practical nurses and students were interviewed to provide insight into interpretation of survey questions. The survey response rate was 28.4% (n=1104/3883). Mean domain scores indicated a high level of confidence in patient safety competence (Nurses of Ontario >2years and in those who obtained their education outside of Canada. Faculty believed their approach to teaching and learning instilled a deep understanding of the limits to practical nurse autonomous practice. Practical nurses were confident in what they learned about patient safety in their educational programs. The high degree of patient safety competence may be a true reflection of practical nurses understanding of, and comfort with, the limits of their knowledge and, ultimately, the limits of their individual autonomous practice. Further exploration as to whether the questionnaire requires additional modification for use with practical nurse populations is warranted. However, this study provides the first examination of practical nurses' perspectives and

From extended integrity monitoring to the safety evaluation of satellite-based localisation system

International Nuclear Information System (INIS)

Legrand, Cyril; Beugin, Julie; Marais, Juliette; Conrard, Blaise; El-Koursi, El-Miloudi; Berbineau, Marion

2016-01-01

Global Navigation Satellite Systems (GNSS) such as GPS, already used in aeronautics for safety-related applications, can play a major role in railway safety by allowing a train to locate itself safely. However, in order to implement this positioning solution in any embedded system, its performances must be evaluated according to railway standards. The evaluation of GNSS performances is not based on the same attributes class than RAMS evaluation. Face to these diffculties, we propose to express the integrity attribute, performance of satellite-based localisation. This attribute comes from aeronautical standards and for a hybridised GNSS with inertial system. To achieve this objective, the integrity attribute must be extended to this kind of system and algorithms initially devoted to GNSS integrity monitoring only must be adapted. Thereafter, the formalisation of this integrity attribute permits us to analyse the safety quantitatively through the probabilities of integrity risk and wrong-side failure. In this paper, after an introductory discussion about the use of localisation systems in railway safety context together with integrity issues, a particular integrity monitoring is proposed and described. The detection events of this algorithm permit us to conclude about safety level of satellite-based localisation system.

Design for safety: theoretical framework of the safety aspect of BIM system to determine the safety index

Directory of Open Access Journals (Sweden)

Ai Lin Evelyn Teo

2016-12-01

Full Text Available Despite the safety improvement drive that has been implemented in the construction industry in Singapore for many years, the industry continues to report the highest number of workplace fatalities, compared to other industries. The purpose of this paper is to discuss the theoretical framework of the safety aspect of a proposed BIM System to determine a Safety Index. An online questionnaire survey was conducted to ascertain the current workplace safety and health situation in the construction industry and explore how BIM can be used to improve safety performance in the industry. A safety hazard library was developed based on the main contributors to fatal accidents in the construction industry, determined from the formal records and existing literature, and a series of discussions with representatives from the Workplace Safety and Health Institute (WSH Institute in Singapore. The results from the survey suggested that the majority of the firms have implemented the necessary policies, programmes and procedures on Workplace Safety and Health (WSH practices. However, BIM is still not widely applied or explored beyond the mandatory requirement that building plans should be submitted to the authorities for approval in BIM format. This paper presents a discussion of the safety aspect of the Intelligent Productivity and Safety System (IPASS developed in the study. IPASS is an intelligent system incorporating the buildable design concept, theory on the detection, prevention and control of hazards, and the Construction Safety Audit Scoring System (ConSASS. The system is based on the premise that safety should be considered at the design stage, and BIM can be an effective tool to facilitate the efforts to enhance safety performance. IPASS allows users to analyse and monitor key aspects of the safety performance of the project before the project starts and as the project progresses.

The micro-processor controlled process radiation monitoring system for reactor safety systems

International Nuclear Information System (INIS)

Mizuno, K.; Noguchi, A.; Kumagami, S.; Gotoh, Y.; Kumahara, T.; Arita, S.

1986-01-01

Digital computers are soon expected to be applied to various real-time safety and safety-related systems in nuclear power plants. Hitachi is now engaged in the development of a micro-processor controlled process radiation monitoring system, which operates on digital processing methods employed with a log ratemeter. A newly defined methodology of design and test procedures is being applied as a means of software program verification for these safety systems. Recently implemented micro-processor technology will help to achieve an advanced man-machine interface and highly reliable performance. (author)

Radiation survey meters used for environmental monitoring

International Nuclear Information System (INIS)

Bjerke, H.; Sigurdsson, T.; Meier Pedersen, K.; Grindborg, J.-E.; Persson, L.; Siiskonen, T.; Hakanen, A.; Kosunen, A.

2012-01-01

The Nordic dosimetry group set up the GammaRate project to investigate how its expertise could be used to assure appropriate usage of survey meters in environmental monitoring. Considerable expertise in calibrating radiation instruments exists in the Nordic radiation protection authorities. The Swedish, Finnish, Danish and Norwegian authorities operate Secondary Standard Dosimetry Laboratories (SSDLs) that provide users with calibration traceable to internationally recognised primary standards. These authorities together with the Icelandic authorities have formally cooperated since 2002 in the field of radiation dosimetry. Dosimetry is the base for assesment of risk from ionising radiation and calibration of instruments is an imported part in dosimetry. The Nordic dosimetry group has been focused on cancer therapy. This work extends the cooperation to the dosimetry of radiation protection and environmental monitoring. This report contains the formal, theoretical and practical background for survey meter measurements. Nordic standards dosimetry laboratories have the capability to provide traceable calibration of instruments in various types of radiation. To verify and explore this further in radiation protection applications a set of survey instruments were sent between the five Nordic countries and each of the authority asked to provide a calibration coefficient for all instruments. The measurement results were within the stated uncertainties, except for some results from NRPA for the ionchamber based instrument. The comparison was shown to be a valuable tool to harmonize the calibration of radiation protection instruments in the Nordic countries. Dosimetry plays an important role in the emergency situations, and it is clear that better traceability and harmonised common guidelines will improve the emergency preparedness and health. (Author)

Radiation survey meters used for environmental monitoring

Energy Technology Data Exchange (ETDEWEB)

Bjerke, H. (ed.) (Norwegian Radiation Protection Authority, NRPA (Norway)); Sigurdsson, T. (Icelandic Radiation Safety Authority, Geislavarnir Rikisins, GR (IS)); Meier Pedersen, K. (National Board of Health, Statens Institut for Straalebeskyttelse (SIS) (Denmark)); Grindborg, J.-E.; Persson, L. (Swedish Radiation Safety Authority, Straalsaekerhetsmyndigheten (SSM) (Sweden)); Siiskonen, T.; Hakanen, A.; Kosunen, A. (Radiation and Nuclear Safety Authority, Saeteilyturvakeskus (STUK) (Finland))

2012-01-15

The Nordic dosimetry group set up the GammaRate project to investigate how its expertise could be used to assure appropriate usage of survey meters in environmental monitoring. Considerable expertise in calibrating radiation instruments exists in the Nordic radiation protection authorities. The Swedish, Finnish, Danish and Norwegian authorities operate Secondary Standard Dosimetry Laboratories (SSDLs) that provide users with calibration traceable to internationally recognised primary standards. These authorities together with the Icelandic authorities have formally cooperated since 2002 in the field of radiation dosimetry. Dosimetry is the base for assesment of risk from ionising radiation and calibration of instruments is an imported part in dosimetry. The Nordic dosimetry group has been focused on cancer therapy. This work extends the cooperation to the dosimetry of radiation protection and environmental monitoring. This report contains the formal, theoretical and practical background for survey meter measurements. Nordic standards dosimetry laboratories have the capability to provide traceable calibration of instruments in various types of radiation. To verify and explore this further in radiation protection applications a set of survey instruments were sent between the five Nordic countries and each of the authority asked to provide a calibration coefficient for all instruments. The measurement results were within the stated uncertainties, except for some results from NRPA for the ionchamber based instrument. The comparison was shown to be a valuable tool to harmonize the calibration of radiation protection instruments in the Nordic countries. Dosimetry plays an important role in the emergency situations, and it is clear that better traceability and harmonised common guidelines will improve the emergency preparedness and health. (Author)

Flammable gas tank safety program: Technical basis for gas analysis and monitoring

International Nuclear Information System (INIS)

Estey, S.D.

1998-01-01

Several Hanford waste tanks have been observed to exhibit periodic releases of significant quantities of flammable gases. Because potential safety issues have been identified with this type of waste behavior, applicable tanks were equipped with instrumentation offering the capability to continuously monitor gases released from them. This document was written to cover three primary areas: (1) describe the current technical basis for requiring flammable gas monitoring, (2) update the technical basis to include knowledge gained from monitoring the tanks over the last three years, (3) provide the criteria for removal of Standard Hydrogen Monitoring System(s) (SHMS) from a waste tank or termination of other flammable gas monitoring activities in the Hanford Tank farms

[Patient safety culture in hospitals: experiences in planning, organising and conducting a survey among hospital staff].

Science.gov (United States)

van Vegten, Amanda; Pfeiffer, Yvonne; Giuliani, Francesca; Manser, Tanja

2011-01-01

This article presents the first hospital-wide survey on patient safety climate, involving all staff (medical and non-medical), in the German-speaking area. Its aim is to share our experiences with planning, organising and conducting this survey. The study was performed at the university hospital in Zurich and had a response rate of 46.8% (2,897 valid questionnaires). The survey instrument ("Patientensicherheitsklimainventar") was based on the Hospital Survey on Patient Safety Culture (AHRQ). Primarily it allowed for assessing the current patient safety climate as well as identifying specific areas for improvement and creating a hospital-wide awareness and acceptance for patient safety issues and interventions (e.g., the introduction of a Critical Incident Reporting System [CIRS]). We discuss the basic principles and the feedback concept guiding the organisation of the overall project. Critical to the success of this project were the guaranteed anonymity of the respondents, adequate communication through well-established channels within the organisation and the commitment of the management across all project phases. Copyright © 2011. Published by Elsevier GmbH.

Monitoring readiness of safety relevant devices in nuclear power plants by means of CRT-colour displays

International Nuclear Information System (INIS)

Haubert, R.; Stokke, R.

1980-01-01

The development of an information system for monitoring readiness of safety relevant devices is encouraged by the requirements of KTA-rule 3501 (DIN 25434), which states in section 4.9.1.1. 'A display shall be provided for giving a survey of the condition of the components of the reactor protection system and the active engineered safeguards including their energy and auxiliary media supplies'. In the first stage of the development which was reported at the Enlarged Halden Programme Group Meeting in Loen, Norway, 5th-9th June, 1978, only the components of parts of a BWR-protection system were considered and no display was provided. This paper outlines the next step in the development which comprises implementation of the active engineered safeguards into the system and development of a display system based on a colour CRT-screen. A prototype of this computer-based system for monitoring of protection systems has been established, and it is planned to demonstrate this prototype system using the computer equipment at GRS, Garching (orig./HP)

Surface Contamination Monitor and Survey Information Management System

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-02-01

Shonka Research Associates, Inc.`s (SRA) Surface Contamination Monitor and Survey Information management System (SCM/SIMS) is designed to perform alpha and beta radiation surveys of floors and surfaces and document the measured data. The SRA-SCM/SIMS technology can be applied to routine operational surveys, characterization surveys, and free release and site closure surveys. Any large nuclear site can make use of this technology. This report describes a demonstration of the SRA-SCM/SIMS technology. This demonstration is part of the chicago Pile-5 (CP-5) Large-Scale Demonstration Project (LSDP) sponsored by the US Department of Energy (DOE), Office of Science and Technology (ST), Deactivation and Decommissioning Focus Area (DDFA). The objective of the LSDP is to select and demonstrate potentially beneficial technologies at the Argonne National Laboratory-East`s (ANL) CP-5 Research Reactor Facility. The purpose of the LSDP is to demonstrate that by using innovative and improved deactivation and decommissioning (D and D) technologies from various sources, significant benefits can be achieved when compared to baseline D and D technologies.

Surface Contamination Monitor and Survey Information Management System

International Nuclear Information System (INIS)

1998-02-01

Shonka Research Associates, Inc.'s (SRA) Surface Contamination Monitor and Survey Information management System (SCM/SIMS) is designed to perform alpha and beta radiation surveys of floors and surfaces and document the measured data. The SRA-SCM/SIMS technology can be applied to routine operational surveys, characterization surveys, and free release and site closure surveys. Any large nuclear site can make use of this technology. This report describes a demonstration of the SRA-SCM/SIMS technology. This demonstration is part of the chicago Pile-5 (CP-5) Large-Scale Demonstration Project (LSDP) sponsored by the US Department of Energy (DOE), Office of Science and Technology (ST), Deactivation and Decommissioning Focus Area (DDFA). The objective of the LSDP is to select and demonstrate potentially beneficial technologies at the Argonne National Laboratory-East's (ANL) CP-5 Research Reactor Facility. The purpose of the LSDP is to demonstrate that by using innovative and improved deactivation and decommissioning (D and D) technologies from various sources, significant benefits can be achieved when compared to baseline D and D technologies

Radiation safety research information database

International Nuclear Information System (INIS)

Yukawa, Masae; Miyamoto, Kiriko; Takeda, Hiroshi; Kuroda, Noriko; Yamamoto, Kazuhiko

2004-01-01

National Institute of Radiological Sciences in Japan began to construct Radiation Safety Research Information Database' in 2001. The research information database is of great service to evaluate the effects of radiation on people by estimating exposure dose by determining radiation and radioactive matters in the environment. The above database (DB) consists of seven DB such as Nirs Air Borne Dust Survey DB, Nirs Environmental Tritium Survey DB, Nirs Environmental Carbon Survey DB, Environmental Radiation Levels, Abe, Metabolic Database for Assessment of Internal Dose, Graphs of Predicted Monitoring Data, and Nirs nuclear installation environment water tritium survey DB. Outline of DB and each DB are explained. (S.Y.)

Safety culture in a pharmacy setting using a pharmacy survey on patient safety culture: a cross-sectional study in China.

Science.gov (United States)

Jia, P L; Zhang, L H; Zhang, M M; Zhang, L L; Zhang, C; Qin, S F; Li, X L; Liu, K X

2014-06-30

To explore the attitudes and perceptions of patient safety culture for pharmacy workers in China by using a Pharmacy Survey on Patient Safety Culture (PSOPSC), and to assess the psychometric properties of the translated Chinese language version of the PSOPSC. Cross-sectional study. Data were obtained from 20 hospital pharmacies in the southwest part of China. We performed χ(2) test to explore the differences on pharmacy staff in different hospital and qualification levels and countries towards patient safety culture. We also computed descriptive statistics, internal consistency coefficients and intersubscale correlation analysis, and then conducted an exploratory factor analysis. A test-retest was performed to assess reproducibility of the items. A total of 630 questionnaires were distributed of which 527 were responded to validly (response rate 84%). The positive response rate for each item ranged from 37% to 90%. The positive response rate on three dimensions ('Teamwork', 'Staff Training and Skills' and 'Staffing, Work Pressure and Pace') was higher than that of Agency for Healthcare Research and Quality (AHRQ) data (pculture at different hospital and qualification levels. The internal consistency of the total survey was comparatively satisfied (Cronbach's α=0.89). The results demonstrated that among the pharmacy staffs surveyed in China, there was a positive attitude towards patient safety culture in their organisations. Identifying perspectives of patient safety culture from pharmacists in different hospital and qualification levels are important, since this can help support decisions about action to improve safety culture in pharmacy settings. The Chinese translation of the PSOPSC questionnaire (V.2012) applied in our study is acceptable. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

A Study of Coal Miners’ Safety Psychological Elements Based on Questionnaire Survey

Directory of Open Access Journals (Sweden)

Li Zeng-bo

2016-01-01

Full Text Available During the production process, the instability of safety psychological elements of coal miners contributes to unsafe behaviors that may result in fatal accident. To search the dominant psychological elements, three types of unsafe psychology, comprising 18 unsafe psychological elements, are obtained by theoretical analysis and site survey. Then, an assessment model is established, and a matched questionnaire is applied to two large modern coal mines in Inner Mongolia Autonomous Region. Based on questionnaire survey results and analytic hierarchy process (AHP, assessment judgment matrixes are constructed, effect weight is calculated, and consistency check is conducted. The analysis results show that safety psychology elements of defective type are the dominant elements that trigger unsafe behaviors of coal miners.

The impact of nurse working hours on patient safety culture: a cross-national survey including Japan, the United States and Chinese Taiwan using the Hospital Survey on Patient Safety Culture

OpenAIRE

Wu, Yinghui; Fujita, Shigeru; Seto, Kanako; Ito, Shinya; Matsumoto, Kunichika; Huang, Chiu-Chin; Hasegawa, Tomonori

2013-01-01

Background A positive patient safety culture (PSC) is one of the most critical components to improve healthcare quality and safety. The Hospital Survey on Patient Safety Culture (HSOPS), developed by the US Agency for Healthcare Research and Quality, has been used to assess PSC in 31 countries. However, little is known about the impact of nurse working hours on PSC. We hypothesized that long nurse working hours would deteriorate PSC, and that the deterioration patterns would vary between coun...

NIOSH national survey of long-haul truck drivers: Injury and safety

Science.gov (United States)

Chen, Guang X.; Sieber, W. Karl; Lincoln, Jennifer E.; Birdsey, Jan; Hitchcock, Edward M.; Nakata, Akinori; Robinson, Cynthia F.; Collins, James W.; Sweeney, Marie H.

2015-01-01

Approximately 1,701,500 people were employed as heavy and tractor-trailer truck drivers in the United States in 2012. The majority of them were long-haul truck drivers (LHTDs). There are limited data on occupational injury and safety in LHTDs, which prompted a targeted national survey. The National Institute of Occupational Safety and Health conducted a nationally representative survey of 1265 LHTDs at 32 truck stops across the contiguous United States in 2010. Data were collected on truck crashes, near misses, moving violations, work-related injuries, work environment, safety climate, driver training, job satisfaction, and driving behaviors. Results suggested that an estimated 2.6% of LHTDs reported a truck crash in 2010, 35% reported at least one crash while working as an LHTD, 24% reported at least one near miss in the previous 7 days, 17% reported at least one moving violation ticket and 4.7% reported a non-crash injury involving days away from work in the previous 12 months. The majority (68%) of non-crash injuries among company drivers were not reported to employers. An estimate of 73% of LHTDs (16% often and 58% sometimes) perceived their delivery schedules unrealistically tight; 24% often continued driving despite fatigue, bad weather, or heavy traffic because they needed to deliver or pick up a load at a given time; 4.5% often drove 10 miles per hours or more over the speed limit; 6.0% never wore a seatbelt; 36% were often frustrated by other drivers on the road; 35% often had to wait for access to a loading dock; 37% reported being noncompliant with hours-of-service rules (10% often and 27% sometimes); 38% of LHTDs perceived their entry-level training inadequate; and 15% did not feel that safety of workers was a high priority with their management. This survey brings to light a number of important safety issues for further research and interventions, e.g., high prevalence of truck crashes, injury underreporting, unrealistically tight delivery schedules

Quality assurance in individual monitoring: A summary of the EURADOS survey 2012

International Nuclear Information System (INIS)

Gilvin, P.; Alves, J.G.; Cherestes, C.; Dijk, J.W.E. van; Lehtinen, M.; Rossi, F.; Vekic, B.

2014-01-01

EURADOS Working Group 2 (WG2) on Harmonization of Individual Monitoring is a network of individual monitoring services (IMSs) that aims to promote quality, technical excellence and good practice in European Member States. To help to improve quality, in 2012 EURADOS WG2 carried out a survey of IMSs in Europe. The survey was sent to about 170 IMS and included questions on: the use of formal quality assurance (QA) standards, QA in dosimetry, matters of practice, and common sources of error. The present paper summarises the main findings of the survey, and compares them with those of an earlier study (2003). The survey found that profile of QA is high amongst the responding IMSs, and that most are following good practice. A majority of services comply with formal quality standards and good attention is paid to traceability, method validation and proficiency testing. There are some areas where lessons can be learned, for example in the assessment of measurement uncertainty; and it remains very instructive to see what the main causes of error are for IMSs in general. - Highlights: • EURADOS has surveyed QA practice amongst European dosimetry services. • The survey was comprehensive, covering most of the monitored workers in Europe. • The profile of QA among IMS is reassuringly high. • Many services follow formal QA standards, e.g. ISO 17025. • But there are still some lessons that can be learned

A security/safety survey of long term care facilities.

Science.gov (United States)

Acorn, Jonathan R

2010-01-01

What are the major security/safety problems of long term care facilities? What steps are being taken by some facilities to mitigate such problems? Answers to these questions can be found in a survey of IAHSS members involved in long term care security conducted for the IAHSS Long Term Care Security Task Force. The survey, the author points out, focuses primarily on long term care facilities operated by hospitals and health systems. However, he believes, it does accurately reflect the security problems most long term facilities face, and presents valuable information on security systems and practices which should be also considered by independent and chain operated facilities.

Survey of instrumentation for environmental monitoring: major update. Volume 3. Radiation

Energy Technology Data Exchange (ETDEWEB)

1979-09-01

This is the third volume of a four-volume (seven-part) series, the culmination of a comprehensive survey of instrumentation for environmental monitoring. Consideration is given to instruments and techniques presently in use and to those developed for other purposes but having possible applications to radiation monitoring. The results of the survey are given as descriptions of the physical and operating characteristics of available instruments, critical comparisons among instrumentation methods, and recommendations of promising methodology and development of new instrumentation. Information is also given regarding the pollutants to be monitored, their characteristics and forms, their sources and pathways, their effects on the ecosystem, and the means of controlling them through process and regulatory controls. The discussion is presented under sections entitled radiation sources; instrumentation: by type of radiation or instrument type; and, instrumentation for specific radionuclides. (JGB)

Survey of instrumentation for environmental monitoring: major update. Volume 3. Radiation

International Nuclear Information System (INIS)

1979-09-01

This is the third volume of a four-volume (seven-part) series, the culmination of a comprehensive survey of instrumentation for environmental monitoring. Consideration is given to instruments and techniques presently in use and to those developed for other purposes but having possible applications to radiation monitoring. The results of the survey are given as descriptions of the physical and operating characteristics of available instruments, critical comparisons among instrumentation methods, and recommendations of promising methodology and development of new instrumentation. Information is also given regarding the pollutants to be monitored, their characteristics and forms, their sources and pathways, their effects on the ecosystem, and the means of controlling them through process and regulatory controls. The discussion is presented under sections entitled radiation sources; instrumentation: by type of radiation or instrument type; and, instrumentation for specific radionuclides

SURVEYS OF ORGANIZATIONAL CULTURE AND SAFETY CULTURE IN NUCLEAR POWER

International Nuclear Information System (INIS)

BROWN, B.S.

2000-01-01

The results of a survey of organizational culture at a nuclear power plant are summarized and compared with those of a similar survey which has been described in the literature on high-reliability organizations. A general-purpose cultural inventory showed a profile of organizational style similar to that reported in the literature; the factor structure for the styles was also similar to that of the plant previously described. A specialized scale designed to measure safety culture did not distinguish among groups within the organization that would be expected to differ

The 8th questionnaire survey report of safety control in nuclear medicine

International Nuclear Information System (INIS)

2008-01-01

A questionnaire survey on safety of nuclear medicine studies was conducted under the subcommittee for radionuclide imaging and nuclear medicine technology of Japan Radioisotope Association to promote patient safety. Questionnaires were sent to 1300 hospitals and 21 clinical laboratories in Japan with 1034 facilities responded (78.3%). Sixty percents of the workers in the facilities were nuclear medicine technologists. Medical doctors comprised 20% of the workers, but 32% in the university hospitals. The number of laboratory technologists decreased in all categories of the facilities. Composite PET/CT scanners increased sharply, whereas 2-detector and 3-detector imaging systems decreased. Regular maintenance was performed in approximately 80% of the SPECT imaging systems, while the single head imaging systems were maintained less frequently. Filmless systems were employed in 25.3% of all of the facilities responded, with the higher rate in the university hospitals. The number of accidents and incidents in the facilities decreased. Falls on floor and fall from an examination bed were reported. The nuclear medicine technologists were concerned about safety mechanism of imaging systems, and dimension and height of examination beds. They also wanted prompt supply of safety information and easy interconnectivity among different data of various vendors' systems. The results of this survey may be a valuable source of information on safety of nuclear medicine procedures. (author)

Patient safety education at Japanese medical schools: results of a nationwide survey.

Science.gov (United States)

Maeda, Shoichi; Kamishiraki, Etsuko; Starkey, Jay

2012-05-10

Patient safety education, including error prevention strategies and management of adverse events, has become a topic of worldwide concern. The importance of the patient safety is also recognized in Japan following two serious medical accidents in 1999. Furthermore, educational curriculum guideline revisions in 2008 by relevant the Ministry of Education includes patient safety as part of the core medical curriculum. However, little is known about the patient safety education in Japanese medical schools partly because a comprehensive study has not yet been conducted in this field. Therefore, we have conducted a nationwide survey in order to clarify the current status of patient safety education at medical schools in Japan. Response rate was 60.0% (n = 48/80). Ninety-eight-percent of respondents (n = 47/48) reported integration of patient safety education into their curricula. Thirty-nine percent reported devoting less than five hours to the topic. All schools that teach patient safety reported use of lecture based teaching methods while few used alternative methods, such as role-playing or in-hospital training. Topics related to medical error theory and legal ramifications of error are widely taught while practical topics related to error analysis such as root cause analysis are less often covered. Based on responses to our survey, most Japanese medical schools have incorporated the topic of patient safety into their curricula. However, the number of hours devoted to the patient safety education is far from the sufficient level with forty percent of medical schools that devote five hours or less to it. In addition, most medical schools employ only the lecture based learning, lacking diversity in teaching methods. Although most medical schools cover basic error theory, error analysis is taught at fewer schools. We still need to make improvements to our medical safety curricula. We believe that this study has the implications for the rest of the world as a

Patient safety education at Japanese medical schools: results of a nationwide survey

Directory of Open Access Journals (Sweden)

Maeda Shoichi

2012-05-01

Full Text Available Abstract Background Patient safety education, including error prevention strategies and management of adverse events, has become a topic of worldwide concern. The importance of the patient safety is also recognized in Japan following two serious medical accidents in 1999. Furthermore, educational curriculum guideline revisions in 2008 by relevant the Ministry of Education includes patient safety as part of the core medical curriculum. However, little is known about the patient safety education in Japanese medical schools partly because a comprehensive study has not yet been conducted in this field. Therefore, we have conducted a nationwide survey in order to clarify the current status of patient safety education at medical schools in Japan. Results Response rate was 60.0% (n = 48/80. Ninety-eight-percent of respondents (n = 47/48 reported integration of patient safety education into their curricula. Thirty-nine percent reported devoting less than five hours to the topic. All schools that teach patient safety reported use of lecture based teaching methods while few used alternative methods, such as role-playing or in-hospital training. Topics related to medical error theory and legal ramifications of error are widely taught while practical topics related to error analysis such as root cause analysis are less often covered. Conclusions Based on responses to our survey, most Japanese medical schools have incorporated the topic of patient safety into their curricula. However, the number of hours devoted to the patient safety education is far from the sufficient level with forty percent of medical schools that devote five hours or less to it. In addition, most medical schools employ only the lecture based learning, lacking diversity in teaching methods. Although most medical schools cover basic error theory, error analysis is taught at fewer schools. We still need to make improvements to our medical safety curricula. We believe that this

Does lean management improve patient safety culture? An extensive evaluation of safety culture in a radiotherapy institute.

Science.gov (United States)

Simons, Pascale A M; Houben, Ruud; Vlayen, Annemie; Hellings, Johan; Pijls-Johannesma, Madelon; Marneffe, Wim; Vandijck, Dominique

2015-02-01

The importance of a safety culture to maximize safety is no longer questioned. However, achieving sustainable culture improvements are less evident. Evidence is growing for a multifaceted approach, where multiple safety interventions are combined. Lean management is such an integral approach to improve safety, quality and efficiency and therefore, could be expected to improve the safety culture. This paper presents the effects of lean management activities on the patient safety culture in a radiotherapy institute. Patient safety culture was evaluated over a three year period using triangulation of methodologies. Two surveys were distributed three times, workshops were performed twice, data from an incident reporting system (IRS) was monitored and results were explored using structured interviews with professionals. Averages, chi-square, logistical and multi-level regression were used for analysis. The workshops showed no changes in safety culture, whereas the surveys showed improvements on six out of twelve dimensions of safety climate. The intention to report incidents not reaching patient-level decreased in accordance with the decreasing number of reports in the IRS. However, the intention to take action in order to prevent future incidents improved (factorial survey presented β: 1.19 with p: 0.01). Due to increased problem solving and improvements in equipment, the number of incidents decreased. Although the intention to report incidents not reaching patient-level decreased, employees experienced sustained safety awareness and an increased intention to structurally improve. The patient safety culture improved due to the lean activities combined with an organizational restructure, and actual patient safety outcomes might have improved as well. Copyright © 2014 Elsevier Ltd. All rights reserved.

A Methodology To Incorporate The Safety Culture Into Probabilistic Safety Assessments

Energy Technology Data Exchange (ETDEWEB)

Park, Sunghyun; Kim, Namyeong; Jae, Moosung [Hanyang University, Seoul (Korea, Republic of)

2015-10-15

In order to incorporate organizational factors into PSA, a methodology needs to be developed. Using the AHP to weigh organizational factors as well as the SLIM to rate those factors, a methodology is introduced in this study. The safety issues related to nuclear safety culture have occurred increasingly. The quantification tool has to be developed in order to include the organizational factor into Probabilistic Safety Assessments. In this study, the state-of-the-art for the organizational evaluation methodologies has been surveyed. This study includes the research for organizational factors, maintenance process, maintenance process analysis models, a quantitative methodology using Analytic Hierarchy Process, Success Likelihood Index Methodology. The purpose of this study is to develop a methodology to incorporate the safety culture into PSA for obtaining more objective risk than before. The organizational factor considered in nuclear safety culture might affect the potential risk of human error and hardware-failure. The safety culture impact index to monitor the plant safety culture can be assessed by applying the developed methodology into a nuclear power plant.

A Methodology To Incorporate The Safety Culture Into Probabilistic Safety Assessments

International Nuclear Information System (INIS)

Park, Sunghyun; Kim, Namyeong; Jae, Moosung

2015-01-01

In order to incorporate organizational factors into PSA, a methodology needs to be developed. Using the AHP to weigh organizational factors as well as the SLIM to rate those factors, a methodology is introduced in this study. The safety issues related to nuclear safety culture have occurred increasingly. The quantification tool has to be developed in order to include the organizational factor into Probabilistic Safety Assessments. In this study, the state-of-the-art for the organizational evaluation methodologies has been surveyed. This study includes the research for organizational factors, maintenance process, maintenance process analysis models, a quantitative methodology using Analytic Hierarchy Process, Success Likelihood Index Methodology. The purpose of this study is to develop a methodology to incorporate the safety culture into PSA for obtaining more objective risk than before. The organizational factor considered in nuclear safety culture might affect the potential risk of human error and hardware-failure. The safety culture impact index to monitor the plant safety culture can be assessed by applying the developed methodology into a nuclear power plant

A Fiber Bragg Grating-Based Monitoring System for Roof Safety Control in Underground Coal Mining

Directory of Open Access Journals (Sweden)

Yiming Zhao

2016-10-01

Full Text Available Monitoring of roof activity is a primary measure adopted in the prevention of roof collapse accidents and functions to optimize and support the design of roadways in underground coalmines. However, traditional monitoring measures, such as using mechanical extensometers or electronic gauges, either require arduous underground labor or cannot function properly in the harsh underground environment. Therefore, in this paper, in order to break through this technological barrier, a novel monitoring system for roof safety control in underground coal mining, using fiber Bragg grating (FBG material as a perceived element and transmission medium, has been developed. Compared with traditional monitoring equipment, the developed, novel monitoring system has the advantages of providing accurate, reliable, and continuous online monitoring of roof activities in underground coal mining. This is expected to further enable the prevention of catastrophic roof collapse accidents. The system has been successfully implemented at a deep hazardous roadway in Zhuji Coal Mine, China. Monitoring results from the study site have demonstrated the advantages of FBG-based sensors over traditional monitoring approaches. The dynamic impacts of progressive face advance on roof displacement and stress have been accurately captured by the novel roadway roof activity and safety monitoring system, which provided essential references for roadway support and design of the mine.

Plasma, a plant safety monitoring and assessment system for VVER-440 reactors

Energy Technology Data Exchange (ETDEWEB)

Hornaes, A.; Hulsund, J. E. [Institutt for energiteknikk (IFE), OECD Halden Reactor Project, Halden (Norway); Lipcsei, S.; Major, Cs.; Racz, A.; Vegh, J. [KFKI, Atomic Energy Research Institute, Budapest (Hungary); Eiler, J. [Paks, Nuclear Power Plant Ltd, Paks (Hungary)

1999-05-15

The objective with the Plant Safety Monitoring and Assessment System (PLASMA) is to develop an operator support system to support the execution of new symptom-based Emergency Operating Procedures for application in VVER reactors, with the Paks NPP in Hungary as the target plant. Many of the VVER reactors are rewriting their EOPs to comply more with Western standards of symptom-based EOPs. In this connection it is desirable to improve the data validation, information integration and presentation for operators when executing the EOPs. The entry-point to a symptom-oriented procedure is defined by the occurrence of a well-defined reactor operation status, with all its symptoms. However, the application of the EOF benefits from an operator support system, which performs plant status and symptom identification reliably and accurately. The development of the PLASMA system is a joint venture between Institutt for energiteknikk (IFE) and KFKI with the NPP Paks as the target plant. The project has been initiated and partly funded by the Science and Technology Agency (STA), Japan through the OECD NEA assistance program. In Hungary, considerable effort has concentrated on the safety reassessment of the Paks NPP and new EOPs are being written, but no comprehensive Operator Support System (OSS) for plant safety assessment is installed. Some safety parameter display functions are incorporated into diverse operator support systems, but an online 'plant safety monitoring and assessment system' is still missing. The present project comprises designing, constructing, testing and installing such an OSS, which to a great extent could support plant operators in their safety assessment work (author) (ml)

A Study on Drug Safety Monitoring Program in India

Science.gov (United States)

Ahmad, A.; Patel, Isha; Sanyal, Sudeepa; Balkrishnan, R.; Mohanta, G. P.

2014-01-01

Pharmacovigilance is useful in assuring the safety of medicines and protecting the consumers from their harmful effects. A number of single drugs as well as fixed dose combinations have been banned from manufacturing, marketing and distribution in India. An important issue about the availability of banned drugs over the counter in India is that sufficient adverse drug reactions data about these drugs have not been reported. The most common categories of drugs withdrawn in the last decade were nonsteroidal antiinflammatory drugs (28%), antidiabetics (14.28%), antiobesity (14.28%), antihistamines (14.28%), gastroprokinetic drugs (7.14%), breast cancer and infertility drugs (7.14%), irritable bowel syndrome and constipation drugs (7.14%) and antibiotics (7.14%). Drug withdrawals from market were made mainly due to safety issues involving cardiovascular events (57.14%) and liver damage (14.28%). Majority of drugs have been banned since 3-5 years in other countries but are still available for sale in India. The present study compares the drug safety monitoring systems in the developed countries such as the USA and UK and provides implications for developing a system that can ensure the safety and efficacy of drugs in India. Absence of a gold standard for a drug safety surveillance system, variations in culture and clinical practice across countries makes it difficult for India to completely adopt another country's practices. There should be a multidisciplinary approach towards drug safety that should be implemented throughout the entire duration spanning from drug discovery to usage by consumers. PMID:25425751

Advances in survey monitoring and deformation analysis of dams

International Nuclear Information System (INIS)

Teskey, W.F.; Biacs, Z.; Ingraham, T.J.

1989-01-01

Survey monitoring is an important method of determining the deformation behavior of structures such as dams. The deformation survey monitoring method used by Alberta Environment is designed to be able to detect horizontal movement in the order of 1.5 cm and vertical movement in the order of 0.5 cm. Using computer simulation, reference and observation points are varied to enable precisions of less than 1 cm at a 95% confidence level. Reference network points are pillars of 20 cm diameter steel pipe driven to refusal, which protrude above ground level to a comfortable instrument height of 1.5 m. Object points are 3 m long, 5 cm diameter steel pipes fitted with a helix base and drilled flush with ground level. Data processing is completely automated from data collection to preparation of report plots, using a microcomputer. If suitable procedures are followed, trigonometric (trig) leveling can replace spirit leveling in deformation surveys. Trig leveling can be used to determine heights of inaccessible points impossible to determine with spirit leveling, and allows totally automated data collection. An example is provided of application of the technique to deformation analysis of the Paddle River Dam situated north of Edmonton. 8 refs., 3 figs

Monitoring system of arch bridge for safety network management

Science.gov (United States)

Joo, Bong Chul; Yoo, Young Jun; Lee, Chin Hyung; Park, Ki Tae; Hwang, Yoon Koog

2010-03-01

Korea has constructed the safety management network monitoring test systems for the civil infrastructure since 2006 which includes airport structure, irrigation structure, railroad structure, road structure, and underground structure. Bridges among the road structure include the various superstructure types which are Steel box girder bridge, suspension bridge, PSC-box-girder bridge, and arch bridge. This paper shows the process of constructing the real-time monitoring system for the arch bridge and the measured result by the system. The arch type among various superstructure types has not only the structural efficiency but the visual beauty, because the arch type superstructure makes full use of the feature of curve. The main measuring points of arch bridges composited by curved members make a difference to compare with the system of girder bridges composited by straight members. This paper also shows the method to construct the monitoring system that considers the characteristic of the arch bridge. The system now includes strain gauges and thermometers, and it will include various sensor types such as CCTV, accelerometers and so on additionally. For the long term and accuracy monitoring, the latest optical sensors and equipments are applied to the system.

Survey of the state of the German safety study

International Nuclear Information System (INIS)

Heuser, F.W.; Kotthoff, K.

1977-01-01

In spring 1976 the Federal Ministry of Research and Technology has ordered a safety study to assess the risk for a nuclear power plant with a PWR. Giving first a survey on the main subtasks of the study the present state of work and some first results are discussed. Assuming a failure of safety systems a core melt event and a subsequent failure of the containment could occur. Corresponding accident sequences are discussed in some detail. Related hereto the results of some calculations for fission product release with respect to different containment failure modes are given. According to the results obtained so far the consequences of a core melt event can essentially be restricted by the retention function of the containment. (orig.) [de

Applying the results of probablistic safety analysis of nuclear power plants: a survey of experience

International Nuclear Information System (INIS)

Andrews, W.B.; Herttrich, M.; Koeberlein, K.; Schwager.

1985-01-01

To date, discussions of the many different types of potential applications of PRA/PSA results and insights to safety-decision-making have been mainly theoretical. Various safety goals have been proposed as decision criteria. However, the discussion on the role of PRA/PSA and Safety Goals in safety-decision-making, especially in licensing, is controversial. A Working Group of the OECD Nuclear Energy Agency is completing a compilation and evaluation of real examples of past and present practical experience with the application of probabilistic methods in reactor safety decision-making, with the idea of developing a common understanding in this area. More than fifty different cases where PRA has influenced decision-making have been surveyed. These include, for example, regulatory changes, fixing of licensing requirements, plant specific modifications of design of operation, prioritization of safety issues and emergency planning. This feedback of experience - both positive and negative - with PRA/PSA applications is considered to provide guidance on how probabilistic approaches can be introduced into current safety practices, and on desirable future developments in probabilistic methods and specific PSA/PRA studies. Generic insights from the survey are given

[2011 after-service customer satisfaction survey of monitoring devices in Shanghai area].

Science.gov (United States)

Wang, Lijun; Li, Bin; Qian, Jianguo; Cao, Shaoping; He, Dehua; Zheng, Yunxin

2013-01-01

In 2011, Shanghai Medical Equipment Management Quality Control Center launched the fifth after-sale service satisfaction survey for medical devices in Shanghai area. There are 8 classes medical devices involving in the survey. This paper demonstrates the investigation results of monitoring devices which are from different manufacturers.

Simulating future uncertainty to guide the selection of survey designs for long-term monitoring

Science.gov (United States)

Garman, Steven L.; Schweiger, E. William; Manier, Daniel J.; Gitzen, Robert A.; Millspaugh, Joshua J.; Cooper, Andrew B.; Licht, Daniel S.

2012-01-01

A goal of environmental monitoring is to provide sound information on the status and trends of natural resources (Messer et al. 1991, Theobald et al. 2007, Fancy et al. 2009). When monitoring observations are acquired by measuring a subset of the population of interest, probability sampling as part of a well-constructed survey design provides the most reliable and legally defensible approach to achieve this goal (Cochran 1977, Olsen et al. 1999, Schreuder et al. 2004; see Chapters 2, 5, 6, 7). Previous works have described the fundamentals of sample surveys (e.g. Hansen et al. 1953, Kish 1965). Interest in survey designs and monitoring over the past 15 years has led to extensive evaluations and new developments of sample selection methods (Stevens and Olsen 2004), of strategies for allocating sample units in space and time (Urquhart et al. 1993, Overton and Stehman 1996, Urquhart and Kincaid 1999), and of estimation (Lesser and Overton 1994, Overton and Stehman 1995) and variance properties (Larsen et al. 1995, Stevens and Olsen 2003) of survey designs. Carefully planned, “scientific” (Chapter 5) survey designs have become a standard in contemporary monitoring of natural resources. Based on our experience with the long-term monitoring program of the US National Park Service (NPS; Fancy et al. 2009; Chapters 16, 22), operational survey designs tend to be selected using the following procedures. For a monitoring indicator (i.e. variable or response), a minimum detectable trend requirement is specified, based on the minimum level of change that would result in meaningful change (e.g. degradation). A probability of detecting this trend (statistical power) and an acceptable level of uncertainty (Type I error; see Chapter 2) within a specified time frame (e.g. 10 years) are specified to ensure timely detection. Explicit statements of the minimum detectable trend, the time frame for detecting the minimum trend, power, and acceptable probability of Type I error (�

The comparison of road safety survey answers between web-panel and face-to-face; Dutch results of SARTRE-4 survey.

Science.gov (United States)

Goldenbeld, C; de Craen, S

2013-09-01

In the Netherlands, a comparison of an online and a face-to-face sample of car drivers was made to study differences on a number of selected questions from the SARTRE-4 road safety survey. Contrary to expectations, there was no indication that online respondents were more likely to come from higher educated or more privileged social groups. Confirming earlier research, the results indicated that online respondents were less inclined to give socially desirable answers and were less inclined to use more extreme ratings in their opinions about measures. Contrary to expectations, face-to-face respondents did not tend to give more positive answers in judgment of road safety measures. Weighting to make samples comparable on gender, age, and education had almost no effect on outcomes. The implications for a transition from face-to-face survey to online panel method are discussed. Copyright © 2013 National Safety Council and Elsevier Ltd. All rights reserved.

Automated extinction monitor for the NLOT site survey

Science.gov (United States)

Kumar Sharma, Tarun

In order to search a few potential sites for the National Large Optical Telescope (NLOT) project, we have initiated a site survey program. Since, most of instruments used for the site survey are custom made, we also started developing our own site characterization instruments. In this process we have designed and developed a device called Automated Extinction Monitor (AEM) and installed the same at IAO, Hanle. The AEM is a small wide field robotic telescope, dedicated to record atmospheric extinction in one or more photometric bands. It gives very accurate statistics of the distribution of photometric nights. In addition to this, instrument also provides the measurement of sky brightness. Here we briefly describe overall instrument and initial results obtained.

Considerations on monitoring needs of advanced, passive safety light water reactors for severe accident management

International Nuclear Information System (INIS)

Bava, G.; Zambardi, F.

1992-01-01

This paper deals with problems concerning information and related instrumentation needs for Accident Management (AM), with special emphasis on Severe Accidents (SA) in the new advanced, passive safety Light Water Reactors (PLWR), presently in a development stage. The passive safety conception adopted in the plants concerned goes parallel with a deeper consideration of SA, that reflects the need of increasing the plant resistance against conditions going beyond traditional ''design basis accidents''. Further, the role of Accident Management (AM) is still emphasized as last step of the defence in depth concept, in spite of the design efforts aimed to reduce human factor importance; as a consequence, the availability of pertinent information on actual plant conditions remains a necessary premise for performing preplanned actions. This information is essential to assess the evolution of the accident scenarios, to monitor the performances of the safety systems, to evaluate the ultimate challenge to the plant safety, and to implement the emergency operating procedures and the emergency plans. Based on these general purposes, the impact of the new conception on the monitoring structure is discussed, furthermore reference is made to the accident monitoring criteria applied in current plants to evaluate the requirements for possible solutions. (orig.)

Measuring safety culture: Application of the Hospital Survey on Patient Safety Culture to radiation therapy departments worldwide.

Science.gov (United States)

Leonard, Sarah; O'Donovan, Anita

Minimizing errors and improving patient safety has gained prominence worldwide in high-risk disciplines such as radiation therapy. Patient safety culture has been identified as an important factor in reducing the incidence of adverse events and improving patient safety in the health care setting. The aim of distributing the Hospital Survey on Patient Safety Culture (HSPSC) to radiation therapy departments worldwide was to assess the current status of safety culture, identify areas for improvement and areas that excel, examine factors that influence safety culture, and raise staff awareness. The safety culture in radiation therapy departments worldwide was evaluated by distributing the HSPSC. A total of 266 participants were recruited from radiation therapy departments and included radiation oncologists, radiation therapists, physicists, and dosimetrists. The positive percent scores for the 12 dimensions of the HSPSC varied from 50% to 79%. The highest composite score among the 12 dimensions was teamwork within units; the lowest composite score was handoffs and transitions. The results indicated that health care professionals in radiation therapy departments felt positively toward patient safety. The HSPSC was successfully applied to radiation therapy departments and provided valuable insight into areas of potential improvement such as teamwork across units, staffing, and handoffs and transitions. Managers and policy makers in radiation therapy may use this assessment tool for focused improvement efforts toward patient safety culture. Copyright © 2017 American Society for Radiation Oncology. Published by Elsevier Inc. All rights reserved.

Development and applicability of Hospital Survey on Patient Safety Culture (HSOPS) in Japan.

Science.gov (United States)

Ito, Shinya; Seto, Kanako; Kigawa, Mika; Fujita, Shigeru; Hasegawa, Toshihiko; Hasegawa, Tomonori

2011-02-07

Patient safety culture at healthcare organizations plays an important role in guaranteeing, improving and promoting overall patient safety. Although several conceptual frameworks have been proposed in the past, no standard measurement tool has yet been developed for Japan. In order to examine possibilities to introduce the Hospital Survey on Patient Safety Culture (HSOPS) in Japan, the authors of this study translated the HSOPS into Japanese, and evaluated its factor structure, internal consistency, and construct validity. Healthcare workers (n = 6,395) from 13 acute care general hospitals in Japan participated in this survey. Confirmatory factor analysis indicated that the Japanese HSOPS' 12-factor model was selected as the most pertinent, and showed a sufficiently high standard partial regression coefficient. The internal reliability of the subscale scores was 0.46-0.88. The construct validity of each safety culture sub-dimension was confirmed by polychoric correlation, and by an ordered probit analysis. The results of the present study indicate that the factor structures of the Japanese and the American HSOPS are almost identical, and that the Japanese HSOPS has acceptable levels of internal reliability and construct validity. This shows that the HSOPS can be introduced in Japan.

Older Driver Safety: A Survey of Psychologists' Attitudes, Knowledge, and Practices.

Science.gov (United States)

Love, Janet; Tuokko, Holly

2016-09-01

Using an online survey, we examined the knowledge, attitudes, and practices with respect to older driver safety concerns of clinical psychologists from across Canada who self-identified as working with at least some drivers over 60 years of age. Eighty-four psychologists completed the survey, and many were aware of the issues relevant to older driver safety, although only about half reported that assessing fitness to drive was an important issue in their practice. The majority (75%) reported that they would benefit from education concerning evaluation of fitness to drive. The primary recommendation emerging from this investigation is to increase efforts to inform and educate psychologists about driving-related assessment and regulatory issues in general, and specifically with respect to older adults. As the population ages, it is of growing importance for all health care providers to understand the influence of mental health conditions-including cognitive impairment and dementia-on driving skills.

The roles of the seismic safety and monitoring systems in the PEC fast reactor

International Nuclear Information System (INIS)

Masoni, P.; Di Tullio, E.M.; Massa, B.; Martelli, A.; Sano, T.

1988-01-01

Two different seismic systems are foreseen in the case of PEC: the seismic safety system, that provides the automatic scram, and the seismic monitoring system. During earthquake, three triaxial seismic switches are triggered if a threshold value of the ground acceleration is exceeded. In this case, the signals from the seismic switches are processed by the safety system (with a 2/3 logic) and the shutdown system is triggered. Peak acceleration is the parameter used by the safety system to quantify the seismic event. This way, however, no information is obtained with regard to earthquake frequency content. Thus, reactor safety is guaranteed by adopting a threshold considerably lower than the Z.P.A. of the Design Basis Earthquake. Furthermore, in the case of significant earthquakes, the seismic motion is measured by about 20 triaxial accelerometers, located both in the free field and on the plant's structures. Data are digitazed and recordered by the seismic monitoring system. This system also elaborates the recordered time-histories providing floor response spectra and compares such spectra to the design values. The above-mentioned elaborations and comparisons are performed in short time for two triaxial measuring positions, thus allowing the Operator to immediately get a more complete information on the seismic event. The complete set of data recorded by the seismic monitoring system also allows the actual dynamic response of the plant to be determined and compared to the design values. On the basis of this comparison the necessary safety analysis can be carried out to verify whether the design limits of the plant were respected: in the positive case the reactor can be restarted. (author)

Road safety issues for bus transport management.

Science.gov (United States)

Cafiso, Salvatore; Di Graziano, Alessandro; Pappalardo, Giuseppina

2013-11-01

Because of the low percentage of crashes involving buses and the assumption that public transport improves road safety by reducing vehicular traffic, public interest in bus safety is not as great as that in the safety of other types of vehicles. It is possible that less attention is paid to the significance of crashes involving buses because the safety level of bus systems is considered to be adequate. The purpose of this study was to evaluate the knowledge and perceptions of bus managers with respect to safety issues and the potential effectiveness of various technologies in achieving higher safety standards. Bus managers were asked to give their opinions on safety issues related to drivers (training, skills, performance evaluation and behaviour), vehicles (maintenance and advanced devices) and roads (road and traffic safety issues) in response to a research survey. Kendall's algorithm was used to evaluate the level of concordance. The results showed that the majority of the proposed items were considered to have great potential for improving bus safety. The data indicated that in the experience of the participants, passenger unloading and pedestrians crossing near bus stops are the most dangerous actions with respect to vulnerable users. The final results of the investigation showed that start inhibition, automatic door opening, and the materials and internal architecture of buses were considered the items most strongly related to bus passenger safety. Brake assistance and vehicle monitoring systems were also considered to be very effective. With the exception of driver assistance systems for passenger and pedestrian safety, the perceptions of the importance of other driver assistance systems for vehicle monitoring and bus safety were not unanimous among the bus company managers who participated in this survey. The study results showed that the introduction of new technologies is perceived as an important factor in improving bus safety, but a better understanding

[Enlightenment of adverse reaction monitoring on safety evaluation of traditional Chinese medicines].

Science.gov (United States)

Song, Hai-bo; Du, Xiao-xi; Ren, Jing-tian; Yang, Le; Guo, Xiao-xin; Pang, Yu

2015-04-01

The adverse reaction monitoring is important in warning the risks of traditional Chinese medicines at an early stage, finding potential quality problems and ensuring the safe clinical medication. In the study, efforts were made to investigate the risk signal mining techniques in line with the characteristics of traditional Chinese medicines, particularly the complexity in component, processing, compatibility, preparation and clinical medication, find early risk signals of traditional Chinese medicines and establish a traditional Chinese medicine safety evaluation system based on adverse reaction risk signals, in order to improve the target studies on traditional Chinese medicine safety, effective and timely control risks and solve the existing frequent safety issue in traditional Chinese medicines.

Patient safety: Safety culture and patient safety ethics

DEFF Research Database (Denmark)

Madsen, Marlene Dyrløv

2006-01-01

,demonstrating significant, consistent and sometimes large differences in terms of safety culture factors across the units participating in the survey. Paper 5 is the results of a study of the relation between safety culture, occupational health andpatient safety using a safety culture questionnaire survey......Patient safety - the prevention of medical error and adverse events - and the initiative of developing safety cultures to assure patients from harm have become one of the central concerns in quality improvement in healthcare both nationally andinternationally. This subject raises numerous...... challenging issues of systemic, organisational, cultural and ethical relevance, which this dissertation seeks to address through the application of different disciplinary approaches. The main focus of researchis safety culture; through empirical and theoretical studies to comprehend the phenomenon, address...

Patient Safety Culture Survey in Pediatric Complex Care Settings: A Factor Analysis.

Science.gov (United States)

Hessels, Amanda J; Murray, Meghan; Cohen, Bevin; Larson, Elaine L

2017-04-19

Children with complex medical needs are increasing in number and demanding the services of pediatric long-term care facilities (pLTC), which require a focus on patient safety culture (PSC). However, no tool to measure PSC has been tested in this unique hybrid acute care-residential setting. The objective of this study was to evaluate the psychometric properties of the Nursing Home Survey on Patient Safety Culture tool slightly modified for use in the pLTC setting. Factor analyses were performed on data collected from 239 staff at 3 pLTC in 2012. Items were screened by principal axis factoring, and the original structure was tested using confirmatory factor analysis. Exploratory factor analysis was conducted to identify the best model fit for the pLTC data, and factor reliability was assessed by Cronbach alpha. The extracted, rotated factor solution suggested items in 4 (staffing, nonpunitive response to mistakes, communication openness, and organizational learning) of the original 12 dimensions may not be a good fit for this population. Nevertheless, in the pLTC setting, both the original and the modified factor solutions demonstrated similar reliabilities to the published consistencies of the survey when tested in adult nursing homes and the items factored nearly identically as theorized. This study demonstrates that the Nursing Home Survey on Patient Safety Culture with minimal modification may be an appropriate instrument to measure PSC in pLTC settings. Additional psychometric testing is recommended to further validate the use of this instrument in this setting, including examining the relationship to safety outcomes. Increased use will yield data for benchmarking purposes across these specialized settings to inform frontline workers and organizational leaders of areas of strength and opportunity for improvement.

Condition Monitoring and Fault Diagnosis for an Antifalling Safety Device

Directory of Open Access Journals (Sweden)

Guangxiang Yang

2015-01-01

Full Text Available There is a constant need for the safe operation and reliability of antifalling safety device (AFSD of an elevator. This paper reports an experimental study on rotation speed and catching torque monitoring and fault diagnosis of an antifalling safety device in a construction elevator. Denoising the signal using wavelet transform is presented in this paper. Based on the denoising effects for several types of wavelets, the sym8 wavelet basis, which introduces the high order approximation and an adaptive threshold, is employed for denoising the signal. The experimental result shows a maximum data error reduction of 7.5% is obtained and SNRs (signal-to-noise ratio of rotation speed and catching torque are improved for 3.9% and 6.4%, respectively.

Real-Time Safety Monitoring and Prediction for the National Airspace System

Science.gov (United States)

Roychoudhury, Indranil

2016-01-01

As new operational paradigms and additional aircraft are being introduced into the National Airspace System (NAS), maintaining safety in such a rapidly growing environment becomes more challenging. It is therefore desirable to have both an overview of the current safety of the airspace at different levels of granularity, as well an understanding of how the state of the safety will evolve into the future given the anticipated flight plans, weather forecasts, predicted health of assets in the airspace, and so on. To this end, we have developed a Real-Time Safety Monitoring (RTSM) that first, estimates the state of the NAS using the dynamic models. Then, given the state estimate and a probability distribution of future inputs to the NAS, the framework predicts the evolution of the NAS, i.e., the future state, and analyzes these future states to predict the occurrence of unsafe events. The entire probability distribution of airspace safety metrics is computed, not just point estimates, without significant assumptions regarding the distribution type and or parameters. We demonstrate our overall approach by predicting the occurrence of some unsafe events and show how these predictions evolve in time as flight operations progress.

Enabling social listening for cardiac safety monitoring: Proceedings from a drug information association-cardiac safety research consortium cosponsored think tank.

Science.gov (United States)

Seifert, Harry A; Malik, Raleigh E; Bhattacharya, Mondira; Campbell, Kevin R; Okun, Sally; Pierce, Carrie; Terkowitz, Jeffrey; Turner, J Rick; Krucoff, Mitchell W; Powell, Gregory E

2017-12-01

This white paper provides a summary of the presentations and discussions from a think tank on "Enabling Social Listening for Cardiac Safety Monitoring" trials that was cosponsored by the Drug Information Association and the Cardiac Safety Research Consortium, and held at the White Oak headquarters of the US Food and Drug Administration on June 3, 2016. The meeting's goals were to explore current methods of collecting and evaluating social listening data and to consider their applicability to cardiac safety surveillance. Social listening is defined as the act of monitoring public postings on the Internet. It has several theoretical advantages for drug and device safety. First, these include the ability to detect adverse events that are "missed" by traditional sources and the ability to detect adverse events sooner than would be allowed by traditional sources, both by affording near-real-time access to data from culturally and geographically diverse sources. Social listening can also potentially introduce a novel patient voice into the conversation about drug safety, which could uniquely augment understanding of real-world medication use obtained from more traditional methodologies. Finally, it can allow for access to information about drug misuse and diversion. To date, the latter 2 of these have been realized. Although regulators from the Food and Drug Administration and the United Kingdom's Medicines and Healthcare Products Regulatory Agency participated in the think tank along with representatives from industry, academia, and patient groups, this article should not be construed to constitute regulatory guidance. Copyright © 2017 Elsevier Inc. All rights reserved.

Psychometric properties of the Hospital Survey on Patient Safety Culture for hospital management (HSOPS_M

Directory of Open Access Journals (Sweden)

Pfeiffer Yvonne

2011-07-01

Full Text Available Abstract Background From a management perspective, it is necessary to examine how a hospital's top management assess the patient safety culture in their organisation. This study examines whether the Hospital Survey on Patient Safety Culture for hospital management (HSOPS_M has the same psychometric properties as the HSOPS for hospital employees does. Methods In 2008, a questionnaire survey including the HSOPS_M was conducted with 1,224 medical directors from German hospitals. When assessing the psychometric properties, we performed a confirmatory factor analysis (CFA. Additionally, we proved construct validity and internal consistency. Results A total of 551 medical directors returned the questionnaire. The results of the CFA suggested a satisfactory global data fit. The indices of local fit indicated a good, but not satisfactory convergent validity. Analyses of construct validity indicated that not all safety culture dimensions were readily distinguishable. However, Cronbach's alpha indicated that the dimensions had an acceptable level of reliability. Conclusion The analyses of the psychometric properties of the HSOPS_M resulted in reasonably good levels of property values. Although the set of dimensions within the HSOPS_M needs further scale refinement, the questionnaire covers a broad range of sub-dimensions and supplies important information on safety culture. The HSOPS_M, therefore, is eligible to measure safety culture from the hospital management's points of view and could be used in nationwide hospital surveys to make inter-organisational comparisons.

HSI for monitoring the critical safety functions status tree of a NPP

International Nuclear Information System (INIS)

Oliveira, Mauro Vitor de; Almeida, Jose Carlos Soares de; Augusto, Silas Cordeiro; Jaime, Guilherme Dutra Gonzaga

2013-01-01

Critical safety function (CSF) is the most significant design concept for prioritize operator actions based on the potential threat to the three barriers (fuel cladding, primary coolant system boundary, and containment) and allows the operator to respond to these threats prior to event diagnosis. CSF has a hierarchical information structure that organizes the system variables affecting the plant safety in terms of goal-means relations. It is important that the operator should be aware of various success paths associated with each CSF in order to respond to unanticipated system failures quickly. When an emergency occurs in NPPs, the operator should monitor CSFs periodically and identify possible success paths as necessary, and try to stabilize or safely shut down the plant using emergency operating procedure (EOP) that includes steps to check the CSFs. This implies that safety function status check may become a cognitively burdensome task that needs to be supported by proper information display. The advanced human-system interface (HSI) in nuclear power plants provides an information environment that supports the operators' burdensome cognitive tasks. This paper describes a CSFs interface design for supporting the operator's tasks to monitor and identify the associated success path for Westinghouse 3-loops NPP. (author)

Criticality safety considerations. Integral Monitored Retrievable Storage (MRS) Facility

International Nuclear Information System (INIS)

1986-09-01

This report summarizes the criticality analysis performed to address criticality safety concerns and to support facility design during the conceptual design phase of the Monitored Retrievable Storage (MRS) Facility. The report addresses the criticality safety concerns, the design features of the facility relative to criticality, and the results of the analysis of both normal operating and hypothetical off-normal conditions. Key references are provided (Appendix C) if additional information is desired by the reader. The MRS Facility design was developed and the related analysis was performed in accordance with the MRS Facility Functional Design Criteria and the Basis for Design. The detailed description and calculations are documented in the Integral MRS Facility Conceptual Design Report. In addition to the summary portion of this report, explanatary notes for various terms, calculation methodology, and design parameters are presented in Appendix A. Appendix B provides a brief glossary of technical terms

Federal Radiological Monitoring and Assessment Center Monitoring Manual Volume 1, Operations

Energy Technology Data Exchange (ETDEWEB)

NSTec Aerial Measurement Systems

2012-07-31

The Monitoring division is primarily responsible for the coordination and direction of: Aerial measurements to delineate the footprint of radioactive contaminants that have been released into the environment. Monitoring of radiation levels in the environment; Sampling to determine the extent of contaminant deposition in soil, water, air and on vegetation; Preliminary field analyses to quantify soil concentrations or depositions; and Environmental and personal dosimetry for FRMAC field personnel, during a Consequence Management Response Team (CMRT) and Federal Radiological Monitoring and Assessment Center (FRMAC) response. Monitoring and sampling techniques used during CM/FRMAC operations are specifically selected for use during radiological emergencies where large numbers of measurements and samples must be acquired, analyzed, and interpreted in the shortest amount of time possible. In addition, techniques and procedures are flexible so that they can be used during a variety of different scenarios; e.g., accidents involving releases from nuclear reactors, contamination by nuclear waste, nuclear weapon accidents, space vehicle reentries, or contamination from a radiological dispersal device. The Monitoring division also provides technicians to support specific Health and Safety Division activities including: The operation of the Hotline; FRMAC facility surveys; Assistance with Health and Safety at Check Points; and Assistance at population assembly areas which require support from the FRMAC. This volume covers deployment activities, initial FRMAC activities, development and implementation of the monitoring and assessment plan, the briefing of field teams, and the transfer of FRMAC to the EPA.

Perceptions of clinical safety climate of the multicultural nursing workforce in Saudi Arabia: a cross-sectional survey.

Science.gov (United States)

Almutairi, Adel F; Gardner, Glenn; McCarthy, Alexandra

2013-01-01

The purpose of this study is to explore the safety climate perceptions of the multicultural nursing workforce, and to investigate the influence of diversity of the multicultural nursing workforce on clinical safety in a large tertiary hospital in Saudi Arabia. Working in a multicultural environment is challenging. Each culture has its own unique characteristics and dimensions that shape the language, lifestyle, beliefs, values, customs, traditions, and patterns of behaviour, which expatriate nurses must come to terms with. However, cultural diversity in the health care environment can potentially affect the quality of care and patient safety. A mixed-method case study (survey, interview and document analysis) was employed. A primary study phase entailed the administration of the Safety Climate Survey (SCS). A population sampling strategy was used and 319 nurses participated, yielding a 76.8% response rate. Descriptive and inferential statistics (Kruskal-Wallis test) were used to analyse survey data. The data revealed the nurses' perceptions of the clinical safety climate in this multicultural environment was unsafe, with a mean score of 3.9 out of 5. No significant difference was found between the age groups, years of nursing experience and their perceptions of the safety climate in this context. A significant difference was observed between the national background categories of nurses and perceptions of safety climate. Cultural diversity within the nursing workforce could have a significant influence on perceptions of clinical safety. These findings have the potential to inform policy and practice related to cultural diversity in Saudi Arabia.

Industrial Safety and Applied Health Physics Division, annual report for 1982

International Nuclear Information System (INIS)

1983-12-01

Activities during the past year are summarized for the Health Physics Department, the Environmental Management Department, and the Safety Department. The Health Physics Department conducts radiation and safety surveys, provides personnel monitoring services for both external and internal radiation, and procures, services, and calibrates appropriate portable and stationary health physics instruments. The Environmental Management Department insures that the activities of the various organizations within ORNL are carried out in a responsible and safe manner. This responsibility involves the measurement, field monitoring, and evaluation of the amounts of radionuclides and hazardous materials released to the environment and the control of hazardous materials used within ORNL. The department also collaborates in the design of ORNL Facilities to help reduce the level of materials released to the environment. The Safety Department is responsible for maintaining a high level of staff safety. This includes aspects of both operational and industrial safety and also coordinates the activities of the Director's Safety Review Committee

Industrial Safety and Applied Health Physics Division, annual report for 1982

Energy Technology Data Exchange (ETDEWEB)

1983-12-01

Activities during the past year are summarized for the Health Physics Department, the Environmental Management Department, and the Safety Department. The Health Physics Department conducts radiation and safety surveys, provides personnel monitoring services for both external and internal radiation, and procures, services, and calibrates appropriate portable and stationary health physics instruments. The Environmental Management Department insures that the activities of the various organizations within ORNL are carried out in a responsible and safe manner. This responsibility involves the measurement, field monitoring, and evaluation of the amounts of radionuclides and hazardous materials released to the environment and the control of hazardous materials used within ORNL. The department also collaborates in the design of ORNL Facilities to help reduce the level of materials released to the environment. The Safety Department is responsible for maintaining a high level of staff safety. This includes aspects of both operational and industrial safety and also coordinates the activities of the Director's Safety Review Committee. (ACR)

Annual evaluation of routine radiological survey/monitoring frequencies for the High Ranking Facilities Deactivating Project at Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1998-12-01

The Bethel Valley Watershed at the Oak Ridge National Laboratory (ORNL) has several Environmental Management (EM) facilities that are designated for deactivation and subsequent decontamination and decommissioning (D and D). The Surplus Facilities Program at ORNL provides surveillance and maintenance support for these facilities as deactivation objectives are completed to reduce the risks associated with radioactive material inventories, etc. The Bechtel Jacobs Company LLC Radiological Control (RADCON) Program has established requirements for radiological monitoring and surveying radiological conditions in these facilities. These requirements include an annual evaluation of routine radiation survey and monitoring frequencies. Radiological survey/monitoring frequencies were evaluated for two High Ranking Facilities Deactivation Project facilities, the Bulk Shielding Facility and Tower Shielding Facility. Considerable progress has been made toward accomplishing deactivation objectives, thus the routine radiological survey/monitoring frequencies are being reduced for 1999. This report identifies the survey/monitoring frequency adjustments and provides justification that the applicable RADCON Program requirements are also satisfied

Introduction of structural health and safety monitoring warning systems for Shenzhen-Hong Kong Western Corridor Shenzhen Bay Bridge

Science.gov (United States)

Li, N.; Zhang, X. Y.; Zhou, X. T.; Leng, J.; Liang, Z.; Zheng, C.; Sun, X. F.

2008-03-01

Though the brief introduction of the completed structural health and safety monitoring warning systems for Shenzhen-Hongkong western corridor Shenzhen bay highway bridge (SZBHMS), the self-developed system frame, hardware and software scheme of this practical research project are systematically discussed in this paper. The data acquisition and transmission hardware and the basic software based on the NI (National Instruments) Company virtual instruments technology were selected in this system, which adopted GPS time service receiver technology and so on. The objectives are to establish the structural safety monitoring and status evaluation system to monitor the structural responses and working conditions in real time and to analyze the structural working statue using information obtained from the measured data. It will be also provided the scientific decision-making bases for the bridge management and maintenance. Potential technical approaches to the structural safety warning systems, status identification and evaluation method are presented. The result indicated that the performance of the system has achieved the desired objectives, ensure the longterm high reliability, real time concurrence and advanced technology of SZBHMS. The innovate achievement which is the first time to implement in domestic, provide the reference for long-span bridge structural health and safety monitoring warning systems design.

Intelligent Packaging Systems: Sensors and Nanosensors to Monitor Food Quality and Safety

Directory of Open Access Journals (Sweden)

Guillermo Fuertes

2016-01-01

Full Text Available The application of nanotechnology in different areas of food packaging is an emerging field that will grow rapidly in the coming years. Advances in food safety have yielded promising results leading to the development of intelligent packaging (IP. By these containers, it is possible to monitor and provide information of the condition of food, packaging, or the environment. This article describes the role of the different concepts of intelligent packaging. It is possible that this new technology could reach enhancing food safety, improving pathogen detection time, and controlling the quality of food and packaging throughout the supply chain.

Survey of bayesian belif nets for quantitative reliability assessment of safety critical software used in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Eom, H.S.; Sung, T.Y.; Jeong, H.S.; Park, J.H.; Kang, H.G.; Lee, K

2001-03-01

As part of the Probabilistic Safety Assessment of safety grade digital systems used in Nuclear Power plants research, measures and methodologies applicable to quantitative reliability assessment of safety critical software were surveyed. Among the techniques proposed in the literature we selected those which are in use widely and investigated their limitations in quantitative software reliability assessment. One promising methodology from the survey is Bayesian Belief Nets (BBN) which has a formalism and can combine various disparate evidences relevant to reliability into final decision under uncertainty. Thus we analyzed BBN and its application cases in digital systems assessment area and finally studied the possibility of its application to the quantitative reliability assessment of safety critical software.

Survey of bayesian belif nets for quantitative reliability assessment of safety critical software used in nuclear power plants

International Nuclear Information System (INIS)

Eom, H. S.; Sung, T. Y.; Jeong, H. S.; Park, J. H.; Kang, H. G.; Lee, K.

2001-03-01

As part of the Probabilistic Safety Assessment of safety grade digital systems used in Nuclear Power plants research, measures and methodologies applicable to quantitative reliability assessment of safety critical software were surveyed. Among the techniques proposed in the literature we selected those which are in use widely and investigated their limitations in quantitative software reliability assessment. One promising methodology from the survey is Bayesian Belief Nets (BBN) which has a formalism and can combine various disparate evidences relevant to reliability into final decision under uncertainty. Thus we analyzed BBN and its application cases in digital systems assessment area and finally studied the possibility of its application to the quantitative reliability assessment of safety critical software

Survey on Monitoring and Quality Controlling of the Mobile Biosignal Delivery.

Science.gov (United States)

Pawar, Pravin A; Edla, Damodar R; Edoh, Thierry; Shinde, Vijay; van Beijnum, Bert-Jan

2017-10-31

A Mobile Patient Monitoring System (MPMS) acquires patient's biosignals and transmits them using wireless network connection to the decision-making module or healthcare professional for the assessment of patient's condition. A variety of wireless network technologies such as wireless personal area networks (e.g., Bluetooth), mobile ad-hoc networks (MANET), and infrastructure-based networks (e.g., WLAN and cellular networks) are in practice for biosignals delivery. The wireless network quality-of-service (QoS) requirements of biosignals delivery are mainly specified in terms of required bandwidth, acceptable delay, and tolerable error rate. An important research challenge in the MPMS is how to satisfy QoS requirements of biosignals delivery in the environment characterized by patient mobility, deployment of multiple wireless network technologies, and variable QoS characteristics of the wireless networks. QoS requirements are mainly application specific, while available QoS is largely dependent on QoS provided by wireless network in use. QoS provisioning refers to providing support for improving QoS experience of networked applications. In resource poor conditions, application adaptation may also be required to make maximum use of available wireless network QoS. This survey paper presents a survey of recent developments in the area of QoS provisioning for MPMS. In particular, our contributions are as follows: (1) overview of wireless networks and network QoS requirements of biosignals delivery; (2) survey of wireless networks' QoS performance evaluation for the transmission of biosignals; and (3) survey of QoS provisioning mechanisms for biosignals delivery in MPMS. We also propose integrating end-to-end QoS monitoring and QoS provisioning strategies in a mobile patient monitoring system infrastructure to support optimal delivery of biosignals to the healthcare professionals.

Assessment of pharmacovigilance approaches for monitoring the safety of antimalarial drugs in pregnancy

NARCIS (Netherlands)

Dellicour, S.O.M.C.

2014-01-01

Post-marketing surveillance of drugs used in pregnancy is challenging, especially in developing countries where resources for pharmacovigilance are rare. There is a need to establish simple but effective systems to monitor safety of drugs given during pregnancy in resource constrained countries.

Research on Safety Monitoring System of Tailings Dam Based on Internet of Things

Science.gov (United States)

Wang, Ligang; Yang, Xiaocong; He, Manchao

2018-03-01

The paper designed and implemented the safety monitoring system of tailings dam based on Internet of things, completed the hardware and software design of sensor nodes, routing nodes and coordinator node by using ZigBee wireless sensor chip CC2630 and 3G/4G data transmission module, developed the software platform integrated with geographic information system. The paper achieved real-time monitoring and data collection of tailings dam dam deformation, seepage line, water level and rainfall for all-weather, the stability of tailings dam based on the Internet of things monitoring is analyzed, and realized intelligent and scientific management of tailings dam under the guidance of the remote expert system.

Technical diagnostics - equipment monitoring for increasing safety and availability of nuclear power plants

International Nuclear Information System (INIS)

Sturm, A.; Foerster, R.

1977-01-01

Utilization of technical diagnostics in equipment monitoring of nuclear power plants for ensuring nuclear safety, economic availability, and for decision making on necessary maintenance is reviewed. Technical diagnostics is subdivided into inspection and early detection of malfunctions. Moreover, combination of technical diagnostics and equipment monitoring, integration of technical diagnostics into maintenance strategy, and problems of introducing early detection of malfunctions into maintenance management of nuclear power plants are also discussed. In addition, a compilation of measuring techniques used in technical diagnostics has been made. The international state of the art of equipment monitoring in PWR nuclear power plants is illustrated by description of the sound and vibration measuring techniques. (author)

Field Application of the Micro Biological Survey Method for the Assessment of the Microbiological Safety of Different Water Sources in Horn of Africa and the Evaluation of the Effectiveness of Moringa Oleifera in Drinking Water Purification.

Science.gov (United States)

Losito, Francesca; Arienzo, Alyexandra; Somma, Daniela; Murgia, Lorenza; Stalio, Ottavia; Zuppi, Paolo; Rossi, Elisabetta; Antonini, Giovanni

2017-06-23

Water monitoring requires expensive instrumentations and skilled technicians. In developing Countries as Africa, the severe economic restrictions and lack of technology make water safety monitoring approaches applied in developed Countries, still not sustainable. The need to develop new methods that are suitable, affordable, and sustainable in the African context is urgent. The simple, economic and rapid Micro Biological Survey (MBS) method does not require an equipped laboratory nor special instruments and skilled technicians, but it can be very useful for routine water analysis. The aim of this work was the application of the MBS method to evaluate the microbiological safety of different water sources and the effectiveness of different drinking water treatments in the Horn of Africa. The obtained results have proved that this method could be very helpful to monitor water safety before and after various purification treatments, with the aim to control waterborne diseases especially in developing Countries, whose population is the most exposed to these diseases. In addition, it has been proved that Moringa oleifera water treatment is ineffective in decreasing bacterial load of Eritrea water samples.

Integrated Status and Effectiveness Monitoring Program - Entiat River Snorkel Surveys and Rotary Screw Trap, 2007.

Energy Technology Data Exchange (ETDEWEB)

Nelle, R.D.

2008-01-01

The USFWS Mid-Columbia River Fishery Resource Office conducted snorkel surveys at 24 sites during the summer and fall periods of 2006 survey periods as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. A total of 37,938 fish from 15 species/genera and an unknown category were enumerated. Chinook salmon were the overall most common fish observed and comprised 15% of fish enumerated followed by rainbow trout (10%) and mountain whitefish (7%). Day surveys were conducted during the summer period 2007 (August), while night surveys were conducted during the fall 2007 (October) surveys. The USFWS Mid-Columbia River Fishery Resource Office (MCFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program (ISEMP) program from August through November of 2007. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 999 wild Oncorhynchus mykiss and 5,107 wild run O. tshawytscha were PIT tagged during the study period. Rotary screw trap efficiencies averaged 22.3% for juvenile O. tshawytscha and 9.0% for juvenile O. mykiss. Rotary screw traps operated 7 days a week and remote capture operations were conducted when flow and temperature regimes permitted. This is third annual progress report to Bonneville Power Administration for the snorkel surveys conducted in the Entiat River as related to long-term effectiveness monitoring of restoration programs in this watershed. The objective of this study is to monitor the fish habitat utilization of planned in-stream restoration efforts in the Entiat River by conducting pre- and post-construction snorkel surveys at selected treatment and control sites.

Survey on the use of configuration risk and safety management tools at nuclear power plants. Final report

International Nuclear Information System (INIS)

Fleming, K.N.; Read, J.W.; Dagan, W.J.; Bidwell, D.A.

1998-09-01

In order to provide input to Electricite de France's (EDF) evaluation of the use of configuration safety and risk management tools in the French plants and to collect information to guide the EPRI efforts to provide useful tools for the EPRI member utilities and international partners, a joint effort to survey US and selected non-US nuclear power stations was conducted. This survey examined the use of various approaches, techniques, and software tools that are being used to evaluate the safety and risk aspects of plant configuration changes and configuration changes during plant outages as well as during power operation. The use of these tools has increased in recent years as a result of efforts to optimize plant maintenance programs, improve plant safety, and increase plant reliability and availability. This report provides the results of the survey of 37 organizations covering 54 nuclear plant sites and 97 reactor units

Benchmarking Global Food Safety Performances: The Era of Risk Intelligence.

Science.gov (United States)

Valleé, Jean-Charles Le; Charlebois, Sylvain

2015-10-01

Food safety data segmentation and limitations hamper the world's ability to select, build up, monitor, and evaluate food safety performance. Currently, there is no metric that captures the entire food safety system, and performance data are not collected strategically on a global scale. Therefore, food safety benchmarking is essential not only to help monitor ongoing performance but also to inform continued food safety system design, adoption, and implementation toward more efficient and effective food safety preparedness, responsiveness, and accountability. This comparative study identifies and evaluates common elements among global food safety systems. It provides an overall world ranking of food safety performance for 17 Organisation for Economic Co-Operation and Development (OECD) countries, illustrated by 10 indicators organized across three food safety risk governance domains: risk assessment (chemical risks, microbial risks, and national reporting on food consumption), risk management (national food safety capacities, food recalls, food traceability, and radionuclides standards), and risk communication (allergenic risks, labeling, and public trust). Results show all countries have very high food safety standards, but Canada and Ireland, followed by France, earned excellent grades relative to their peers. However, any subsequent global ranking study should consider the development of survey instruments to gather adequate and comparable national evidence on food safety.

Statistical considerations in practical contamination monitoring

International Nuclear Information System (INIS)

Brodsky, A.; Gallaghar, R.G.

1991-01-01

This paper reports on an examination of smear survey practices which indicates that many radiation safety programs are lacking in important aspects of contamination monitoring. In order to satisfy regulatory and potential litigatory requirements, smear surveys should include the measurement and recording of the flowing data: area of each smear and smear procedure (by reference); total counts on smear and counting procedure; total counts on appropriate blanks and description of blank; total counts on standard and specifications of standard; and all counting times. The rationale for these smear survey requirements is obtained by examining the formulation of the minimum detectable amount (MDA) on a smear

Results of a survey on accident and safety analysis codes, benchmarks, verification and validation methods

International Nuclear Information System (INIS)

Lee, A.G.; Wilkin, G.B.

1995-01-01

This report is a compilation of the information submitted by AECL, CIAE, JAERI, ORNL and Siemens in response to a need identified at the 'Workshop on R and D Needs' at the IGORR-3 meeting. The survey compiled information on the national standards applied to the Safety Quality Assurance (SQA) programs undertaken by the participants. Information was assembled for the computer codes and nuclear data libraries used in accident and safety analyses for research reactors and the methods used to verify and validate the codes and libraries. Although the survey was not comprehensive, it provides a basis for exchanging information of common interest to the research reactor community

A survey on management perspectives of the state of workplace health and safety practices in Kenya.

Science.gov (United States)

Mbakaya, C F; Onyoyo, H A; Lwaki, S A; Omondi, O J

1999-07-01

A baseline survey was conducted in 1995 on management perspectives of occupational health and safety (OHS) structures and practices in Kenya. This was achieved by interviewing management and supervisory staff attending 1 week multi-disciplinary courses that were organized by the Federation of Kenya Employers (FKE) and the International Labour Office (ILO) at hotel venues in Kenya. The purpose of the survey was to gain some insight into work safety conditions in Kenya and to assess the potential for a new OHS manual to meet existing knowledge gaps. The manual was locally developed in 1993/4 by Kenyan OHS experts in collaboration with colleagues from the Swedish National Institute for Working Life. Results of the survey from 65 participants indicated that most workplace managers were not familiar with the Kenyan work safety legislation. Work injuries were largely attributable to working with dangerous machinery. Occupational diseases and HIV/AIDS were cited as other causes of workplace morbidity and mortality. Although most respondents (70%) were satisfied with their work safety conditions, only 37% said their workplaces were annually audited by labour inspectors while 45% said injured workers were not treated well by management. Many workplaces (65%) violated the mandatory legal requirement on the establishment of health and safety committees. The OHS resource person and course content were rated highly by most respondents (96%). The foregoing results provided the basis of a needs analysis for future OHS programs in Kenya.

Network analytical tool for monitoring global food safety highlights China.

Directory of Open Access Journals (Sweden)

Tamás Nepusz

Full Text Available BACKGROUND: The Beijing Declaration on food safety and security was signed by over fifty countries with the aim of developing comprehensive programs for monitoring food safety and security on behalf of their citizens. Currently, comprehensive systems for food safety and security are absent in many countries, and the systems that are in place have been developed on different principles allowing poor opportunities for integration. METHODOLOGY/PRINCIPAL FINDINGS: We have developed a user-friendly analytical tool based on network approaches for instant customized analysis of food alert patterns in the European dataset from the Rapid Alert System for Food and Feed. Data taken from alert logs between January 2003-August 2008 were processed using network analysis to i capture complexity, ii analyze trends, and iii predict possible effects of interventions by identifying patterns of reporting activities between countries. The detector and transgressor relationships are readily identifiable between countries which are ranked using i Google's PageRank algorithm and ii the HITS algorithm of Kleinberg. The program identifies Iran, China and Turkey as the transgressors with the largest number of alerts. However, when characterized by impact, counting the transgressor index and the number of countries involved, China predominates as a transgressor country. CONCLUSIONS/SIGNIFICANCE: This study reports the first development of a network analysis approach to inform countries on their transgressor and detector profiles as a user-friendly aid for the adoption of the Beijing Declaration. The ability to instantly access the country-specific components of the several thousand annual reports will enable each country to identify the major transgressors and detectors within its trading network. Moreover, the tool can be used to monitor trading countries for improved detector/transgressor ratios.

Undetected latent failures of safety-related systems. Preliminary survey of events in nuclear power plants 1980-1997

International Nuclear Information System (INIS)

Lydell, B.

1998-03-01

This report summarizes results and insights from a preliminary survey of events involving undetected, latent failures of safety-related systems. The survey was limited to events where mispositioned equipment (e.g., valves, switches) remained undetected, thus rendering standby equipment or systems unavailable for short or long time periods. Typically, these events were symptoms of underlying latent errors (e.g., design errors, procedure errors, unanalyzed safety conditions) and programmatic errors. The preliminary survey identified well over 300 events. Of these, 95 events are documented in this report. Events involving mispositioned equipment are commonplace. Most events are discovered soon after occurrence, however. But as evidenced by the survey results, some events remained undetected beyond several shift changes. The recommendations developed by the survey emphasize the importance of applying modern root cause analysis techniques to the event analysis to ensure that the causes and implications of occurred events are fully understood

Traffic Tech : National Telephone Survey on Distracted Driving Attitudes and Behaviors - 2015

Science.gov (United States)

2018-03-01

The National Highway Traffic Safety Administration (NHTSA) conducted its third national telephone survey of distracted driving to monitor the public's attitudes, knowledge, and self-reported behavior about cell phone use and texting while driving, an...

Wide Range Portable Radiation Survey Meter for Emergency Monitoring

Energy Technology Data Exchange (ETDEWEB)

Gangadharan, P.; Bhave, D. G.; Gokarn, R. S.; Khadake, R. G. [Directorate Of Radiation Protection, Bhabha Atomic Research Centre, Trombay, Bombay (India)

1969-05-15

The paper describes a portable battery-operated radiation survey meter for monitoring a wide range of X- and gamma-ray exposure rates from 1 mR/h to 100 R/h. The instrument Incorporates a halogen GM tube as the detector and a count-rate meter for indication. A transistorized d.c. -d.c. converter supplies the necessary high voltage to the GM counter. The instrument response has been made energy independent in the energy range 80 keV to 1.25 MeV. Further, the response is linear over the entire range of exposure rates. Suitable extension rods have been designed to provide sufficient separation between the probe and the meter in cases where remote monitoring is necessary because of high fields. (author)

Self-monitoring blood pressure in patients with hypertension: an internet-based survey of UK GPs.

Science.gov (United States)

Fletcher, Benjamin R; Hinton, Lisa; Bray, Emma P; Hayen, Andrew; Hobbs, Fd Richard; Mant, Jonathan; Potter, John F; McManus, Richard J

2016-11-01

Previous research suggests that most GPs in the UK use self-monitoring of blood pressure (SMBP) to monitor the control of hypertension rather than for diagnosis. This study sought to assess current practice in the use of self-monitoring and any changes in practice following more recent guideline recommendations. To survey the views and practice of UK GPs in 2015 with regard to SMBP and compare them with a previous survey carried out in 2011. Web-based survey of a regionally representative sample of 300 UK GPs. GPs completed an online questionnaire concerning the use of SMBP in the management of hypertension. Analyses comprised descriptive statistics, tests for between-group differences (z, Wilcoxon signed-rank, and χ 2 tests), and multivariate logistic regression. Results were available for 300 GPs (94% of those who started the survey). GPs reported using self-monitoring to diagnose hypertension (169/291; 58%; 95% confidence interval (CI) = 52 to 64) and to monitor control (245/291; 84%; 95% CI = 80 to 88), the former having significantly increased since 2011 (from 37%; 95% CI = 33 to 41; Pmonitoring for control. More than half of GPs used higher systolic thresholds for diagnosis (118/169; 70%; 95% CI = 63 to 77) and treatment (168/225; 75%; 95% CI = 69 to 80) than recommended in guidelines, and under half (120/289; 42%; 95% CI = 36 to 47) adjusted the SMBP results to guide treatment decisions. Since new UK national guidance in 2011, GPs are more likely to use SMBP to diagnose hypertension. However, significant proportions of GPs continue to use non-standard diagnostic and monitoring thresholds. The use of out-of-office methods to improve the accuracy of diagnosis is unlikely to be beneficial if suboptimal thresholds are used. © British Journal of General Practice 2016.

Undetected latent failures of safety-related systems. Preliminary survey of events in nuclear power plants 1980-1997

Energy Technology Data Exchange (ETDEWEB)

Lydell, B. [RSA Technologies, Vista, CA (United States)

1998-03-01

This report summarizes results and insights from a preliminary survey of events involving undetected, latent failures of safety-related systems. The survey was limited to events where mispositioned equipment (e.g., valves, switches) remained undetected, thus rendering standby equipment or systems unavailable for short or long time periods. Typically, these events were symptoms of underlying latent errors (e.g., design errors, procedure errors, unanalyzed safety conditions) and programmatic errors. The preliminary survey identified well over 300 events. Of these, 95 events are documented in this report. Events involving mispositioned equipment are commonplace. Most events are discovered soon after occurrence, however. But as evidenced by the survey results, some events remained undetected beyond several shift changes. The recommendations developed by the survey emphasize the importance of applying modern root cause analysis techniques to the event analysis to ensure that the causes and implications of occurred events are fully understood. 7 refs, 4 tabs, 3 figs. Also available at the SKI Home page: //www.ski.se.

Barriers to Implementing a Reporting and Learning Patient Safety System: Pediatric Chiropractic Perspective.

Science.gov (United States)

Pohlman, Katherine A; Carroll, Linda; Hartling, Lisa; Tsuyuki, Ross T; Vohra, Sunita

2016-04-01

A reporting and learning system is a method of monitoring the occurrence of incidents that affect patient safety. This cross-sectional survey asked pediatric chiropractors about factors that may limit their participation in such a system. The list of potential barriers for participation was developed using a systematic approach. All members of the 2 pediatric councils associated with US national chiropractic organizations were invited to complete the survey (N = 400). The cross-sectional survey was created using an online survey tool (REDCap) and sent directly to member emails addressed by the respective executive committees. Of the 400 potential respondents, 81 responded (20.3%). The most common limitations to participating were identified as time pressure (96%) and patient concerns (81%). Reporting and learning systems have been utilized to increase safety awareness in many high-risk industries. To be successful, future patient safety studies with pediatric chiropractors need to ensure these barriers are understood and addressed. © The Author(s) 2015.

John F. Kennedy Space Center, Safety, Reliability, Maintainability and Quality Assurance, Survey and Audit Program

Science.gov (United States)

1994-01-01

This document is the product of the KSC Survey and Audit Working Group composed of civil service and contractor Safety, Reliability, and Quality Assurance (SR&QA) personnel. The program described herein provides standardized terminology, uniformity of survey and audit operations, and emphasizes process assessments rather than a program based solely on compliance. The program establishes minimum training requirements, adopts an auditor certification methodology, and includes survey and audit metrics for the audited organizations as well as the auditing organization.

Test and assessment method of Automotive Safety Systems (SSB) particularly to monitor traffic incidents

Science.gov (United States)

Pijanowski, B.; Łukjanow, S.; Burliński, R.

2016-09-01

The rapid development of telematics, particularly mobile telephony (GSM), wireless data transmission (GPRS) and satellite positioning (GPS) noticeable in the last decade, resulted in an almost unlimited growth of the possibilities for monitoring of mobile objects. These solutions are already widely used in the so-called “Intelligent Transport Systems” - ITS and affect a significant increase for road safety. The article describes a method of testing and evaluation of Car Safety Systems (Polish abbreviation - SSB) especially for monitoring traffic incidents, such as collisions and accidents. The algorithm of SSB testing process is also presented. Tests are performed on the dynamic test bench, part of which is movable platform with car security system mounted on it. Crash tests with a rigid obstacle are carried out instead of destructive attempts to crash test of the entire vehicle which is expensive. The tested system, depending on the simulated traffic conditions, is mounted in such a position and with the use of components, indicated by the manufacturer for the automotive safety system installation in a vehicle, for which it is intended. Then, the tests and assessments are carried out.

Animal-assisted interventions: A national survey of health and safety policies in hospitals, eldercare facilities, and therapy animal organizations.

Science.gov (United States)

Linder, Deborah E; Siebens, Hannah C; Mueller, Megan K; Gibbs, Debra M; Freeman, Lisa M

2017-08-01

Animal-assisted intervention (AAI) programs are increasing in popularity, but it is unknown to what extent therapy animal organizations that provide AAI and the hospitals and eldercare facilities they work with implement effective animal health and safety policies to ensure safety of both animals and humans. Our study objective was to survey hospitals, eldercare facilities, and therapy animal organizations on their AAI policies and procedures. A survey of United States hospitals, eldercare facilities, and therapy animal organizations was administered to assess existing health and safety policies related to AAI programs. Forty-five eldercare facilities, 45 hospitals, and 27 therapy animal organizations were surveyed. Health and safety policies varied widely and potentially compromised human and animal safety. For example, 70% of therapy animal organizations potentially put patients at risk by allowing therapy animals eating raw meat diets to visit facilities. In general, hospitals had stricter requirements than eldercare facilities. This information suggests that there are gaps between the policies of facilities and therapy animal organizations compared with recent guidelines for animal visitation in hospitals. Facilities with AAI programs need to review their policies to address recent AAI guidelines to ensure the safety of animals and humans involved. Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Atomics International environmental monitoring and facility effluent annual report, 1976

International Nuclear Information System (INIS)

Moore, J.D.

1977-01-01

Environmental and facility effluent radioactivity monitoring at Atomics International (AI) is performend by the Radiation and Nuclear Safety Unit of the Health, Safety, and Radiation Services Department. Soil, vegetation, and surface water are routinely sampled to a distance of 10 miles from AI sites. Continuous ambient air sampling and thermoluminescent dosimetry are performed on site for monitoring airborne radioactivity and site ambient radiation levels. Radioactivity in effluents discharged to the atmosphere from AI facilities is continuously sampled and monitored to ensure that levels released to unrestricted areas are within appropriate limits, and to identify processes which may require additional engineering safeguards to minimize radioactivity levels in such effluents. In addition, selected nonradioactive constituents in surface water discharged to unrestricted areas are determined. This report summarizes and discusses monitoring results for 1976. The results of a special soil plutonium survey performed during the year are also summarized

Assessment of safety culture in isfahan hospitals (2010).

Science.gov (United States)

Raeisi, Ahmed Reza; Nazari, Maryam; Bahmanziari, Najme

2013-01-01

Many internal and external risk factors in health care organizations make safety important and it has caused the management to consider safety in their mission statement. One of the most important tools is to establish the appropriate organizational structure and safety culture. The goal of this research is to inform managers and staff about current safety culture status in hospitals in order to improve the efficiency and effectiveness of health services. This is a descriptive-survey research. The research population was selected hospitals of Isfahan, Iran. Research tool was a questionnaire (Cronbach alpha 0.75). The questionnaire including 93 questions (Likert scale) classified in 12 categories: Demographic questions, Individual attitude, management attitude, Safety Training, Induced stress, pressure and emotional conditions during work, Consultation and participation, Communications, Monitoring and control, work environment, Reporting, safety Rules, procedures and work instructions that distributed among 45 technicians, 208 Nurses and 62 Physicians. All data collected from the serve was analysis with statistical package of social science (SPSS). In this survey Friedman test, Spearman correlation, analysis of variance (ANOVA) and factor analysis have been used for data analyzing. The score of safety culture dimensions was 2.90 for Individual attitude, 3.12 for management attitude, 3.32 for Safety Training, 3.14 for Induced stress, pressure and emotional conditions during work, 3.31 for Consultation and participation, 2.93 for Communications, 3.28 for Monitoring and control, 3.19 for work environment, 3.36 for Reporting, 3.59 safety Rules, procedures and work instructions that Communication and individual attitude were in bad condition. Safety culture among different hospitals: governmental and educational, governmental and non-educational and non-governmental and different functional groups (physicians, nurses, diagnostic) of studied hospitals showed no

Violet Grove CO{sub 2} injection project : monitoring with timelapse VSP surveys

Energy Technology Data Exchange (ETDEWEB)

Coueslan, M.; Lawton, D. [Calgary Univ., Calgary, AB (Canada); Jones, M. [Schlumberger Canada Ltd., Calgary, AB (Canada)

2006-07-01

Several oil and gas fields in western Canada have been depleted through primary production and secondary recovery methods. Injecting carbon dioxide (CO{sub 2}) into a reservoir can enhance oil recovery (EOR) and has the potential benefit of CO{sub 2} sequestration, which reduces greenhouse gas emissions into the atmosphere. It has been estimated that western Canada has a practical CO{sub 2} storage capacity of about 3.3 Gt in its oil and gas reservoirs. In order to claim a reduction in CO{sub 2} emissions, however, the injected CO{sub 2} must be monitored to prove that it is being trapped in these reservoirs. For that reason, the Violet Grove site, near Drayton Valley, Alberta was chosen as a pilot site to study CO{sub 2} injection into a reservoir for enhanced recovery and carbon sequestration purposes. The reservoir is located in the Cardium Formation in the Pembina Field. It was expected that the CO{sub 2} would flow preferentially in the reservoir's dominant fracture orientation, which is northeast-southwest. Simultaneously acquired time-lapse multicomponent surface and borehole seismic surveys were used to monitor changes in the reservoir. Prior to CO{sub 2} injection, a baseline survey was acquired in March 2005. A second survey was acquired 8 months after CO{sub 2} injection. The borehole seismic data displayed higher bandwidth and increased resolution compared to the surface seismic data. The PS-wave borehole seismic data in particular showed much better results. Together, these seismic surveys provide lateral coverage of the area as well as high resolution images near the observation well. Preliminary results from the time-lapse analysis show an increase of 30 to 60 per cent in the reservoir reflectivity amplitudes in the 8 months between the baseline and monitor surveys, suggesting that the CO{sub 2} flood has progressed southwest of the injector, most likely along the dominant fracture trend. 7 refs., 5 figs.

Development and application of the San Onofre safety monitor

International Nuclear Information System (INIS)

Hook, Thomas G.; Lee, Roger J.; Morgan, Thomas A.

2004-01-01

Halliburton NUS Corporation (NUS) has developed a risk-based configuration management software tool for use at Southern California Edison's San Onofre Nuclear Generating Station. The software, called the Safety Monitor, calculates an estimate of current plant core damage risk based upon the plant's current operating configuration (e.g., equipment operability, system operating alignments). All data is entered and displayed in a format easily understood by plant personnel. The plant hopes to use this tool to ensure that risk is minimized during plant operations and to identify situations in which current Technical Specifications can be optimized. Plant configuration data and out-of-service time data is also automatically collected. (author)

A Survey of Intravenous Remifentanil Use for Labor Analgesia at Academic Medical Centers in the United States.

Science.gov (United States)

Aaronson, Jaime; Abramovitz, Sharon; Smiley, Richard; Tangel, Virginia; Landau, Ruth

2017-04-01

Remifentanil is most commonly offered when neuraxial labor analgesia is contraindicated. There is no consensus regarding the optimal administration, dosing strategy, or requirements for maternal monitoring, which may pose a patient safety issue. This exploratory survey evaluated the current practices regarding remifentanil use for labor analgesia at academic centers in the United States. Of 126 obstetric anesthesia directors surveyed, 84 (67%) responded. In 2014 to 2015, an estimated 36% (95% confidence interval: 25.7-46.3) of centers used remifentanil, most of which did so less than 5 times. Some serious maternal and neonatal respiratory complications occurred, emphasizing that clinical protocols and adequate monitoring are key to ensure maternal and neonatal safety.

Patient safety climate profiles across time: Strength and level of safety climate associated with a quality improvement program in Switzerland—A cross-sectional survey study

Science.gov (United States)

Mascherek, Anna C.

2017-01-01

Safety Climate has been acknowledged as an unspecific factor influencing patient safety. However, studies rarely provide in-depth analysis of climate data. As a helpful approach, the concept of “climate strength” has been proposed. In the present study we tested the hypotheses that even if safety climate remains stable on mean-level across time, differences might be evident in strength or shape. The data of two hospitals participating in a large national quality improvement program were analysed for differences in climate profiles at two measurement occasions. We analysed differences on mean-level, differences in percent problematic response, agreement within groups, and frequency histograms in two large hospitals in Switzerland at two measurement occasions (2013 and 2015) applying the Safety Climate Survey. In total, survey responses of 1193 individuals were included in the analyses. Overall, small but significant differences on mean-level of safety climate emerged for some subgroups. Also, although agreement was strong at both time-points within groups, tendencies of divergence or consensus were present in both hospitals. Depending on subgroup and analyses chosen, differences were more or less pronounced. The present study illustrated that taking several measures into account and describing safety climate from different perspectives is necessary in order to fully understand differences and trends within groups and to develop interventions addressing the needs of different groups more precisely. PMID:28753633

Environmental monitoring in Finland 2006-2008

International Nuclear Information System (INIS)

Niemi, J.

2006-01-01

This publication presents environmental monitoring carried out in Finland in 2006-2008. It is a summary of the environmental monitoring activities of the following national institutes: Geological Survey of Finland, Finnish Meteorological Institute, National Public Health Institute, Plant Production Inspection Centre, Finnish Museum of Natural History, Agrifood Research Finland, Finnish Institute of Marine Research, Finnish Forest Research Institute, Information Centre of the Ministry of Agriculture and Forestry, Finnish Game and Fisheries Research Institute, Radiation and Nuclear Safety Authority, Ministry of Social Affairs and Health, Statistics Finland, Finnish Environment Institute, and Regional Environment Centres. Monitoring of natural resources, environmental pressures, state of the environment, water and health, land use and environmental policy are presented. The objective was to compile the information on national environmental monitoring and to activate information exchange and cooperation in this field. (orig.)

Challenging patient safety culture: survey results

NARCIS (Netherlands)

Hellings, Johan; Schrooten, Ward; Klazinga, Niek; Vleugels, Arthur

2007-01-01

PURPOSE: The purpose of this paper is to measure patient safety culture in five Belgian general hospitals. Safety culture plays an important role in the approach towards greater patient safety in hospitals. DESIGN/METHODOLOGY/APPROACH: The Patient Safety Culture Hospital questionnaire was

Application of the Digital Image Technology in the Visual Monitoring and Prediction of Shuttering Construction Safety

Science.gov (United States)

Ummin, Okumura; Tian, Han; Zhu, Haiyu; Liu, Fuqiang

2018-03-01

Construction safety has always been the first priority in construction process. The common safety problem is the instability of the template support. In order to solve this problem, the digital image measurement technology has been contrived to support real-time monitoring system which can be triggered if the deformation value exceed the specified range. Thus the economic loss could be reduced to the lowest level.

Six years of aerial and ground monitoring surveys for sudden oak death in California

Science.gov (United States)

Lisa Bell; Jeff Mai; Zachary Heath; Erik Haunreiter; Lisa M. Fischer

2008-01-01

Aerial surveys have been conducted since 2001 to map recent hardwood mortality and consequently target ground visits for detection of Phytophthora ramorum, the pathogen that causes sudden oak death (SOD). Each year the aerial and ground surveys monitored much of California?s forests at risk for SOD resulting in new maps of hardwood mortality,...

Survey of college students' MP3 listening: Habits, safety issues, attitudes, and education.

Science.gov (United States)

Hoover, Alicia; Krishnamurti, Sridhar

2010-06-01

To survey listening habits and attitudes of typical college students who use MP3 players and to investigate possible safety issues related to MP3 player listening. College students who were frequent MP3 player users (N = 428) filled out a 30-item online survey. Specific areas probed by the present survey included frequency and duration of MP3 player use, MP3 player volume levels used, types of earphones used, typical environments in which MP3 player was worn, specific activities related to safety while listening to MP3 players, and attitudes toward MP3 player use. The majority of listeners wore MP3 players for less than 2 hr daily at safe volume levels. About one third of respondents reported being distracted while wearing an MP3 player, and more than one third of listeners experienced soreness in their ears after a listening session. About one third of respondents reported occasionally using their MP3 players at maximum volume levels. Listeners indicated willingness to (a) reduce volume levels, (b) decrease listening duration, and (c) buy specialized earphones to conserve their hearing. The study found concerns regarding the occasional use of MP3 players at full volume and reduced environmental awareness among some college student users.

National Food Safety Systems in the European Union: A Comparative Survey

Directory of Open Access Journals (Sweden)

Andreas Hadjigeorgiou

2013-04-01

Full Text Available This paper is a comparative survey of the National Food Safety Systems (NFSS of the European Union (EU Member-States (MS and the Central EU level. The main organizational structures of the NFSS, their legal frameworks, their responsibilities, their experiences, and challenges relating to food safety are discussed. Growing concerns about food safety have led the EU itself, its MS and non-EU countries, which are EU trade-partners, to review and modify their food safety systems. Our study suggests that the EU and 22 out of 27 Member States (MS have reorganized their NFSS by establishing a single food safety authority or a similar organization on the national or central level. In addition, the study analyzes different approaches towards the establishment of such agencies. Areas where marked differences in approaches were seen included the division of responsibilities for risk assessment (RA, risk management (RM, and risk communication (RC. We found that in 12 Member States, all three areas of activity (RA, RM, and RC are kept together, whereas in 10 Member States, risk management is functionally or institutionally separate from risk assessment and risk communication. No single ideal model for others to follow for the organization of a food safety authority was observed; however, revised NFSS, either in EU member states or at the EU central level, may be more effective from the previous arrangements, because they provide central supervision, give priority to food control programs, and maintain comprehensive risk analysis as part of their activities.

Lightweight monitoring and control system for coal mine safety using REST style.

Science.gov (United States)

Cheng, Bo; Cheng, Xin; Chen, Junliang

2015-01-01

The complex environment of a coal mine requires the underground environment, devices and miners to be constantly monitored to ensure safe coal production. However, existing coal mines do not meet these coverage requirements because blind spots occur when using a wired network. In this paper, we develop a Web-based, lightweight remote monitoring and control platform using a wireless sensor network (WSN) with the REST style to collect temperature, humidity and methane concentration data in a coal mine using sensor nodes. This platform also collects information on personnel positions inside the mine. We implement a RESTful application programming interface (API) that provides access to underground sensors and instruments through the Web such that underground coal mine physical devices can be easily interfaced to remote monitoring and control applications. We also implement three different scenarios for Web-based, lightweight remote monitoring and control of coal mine safety and measure and analyze the system performance. Finally, we present the conclusions from this study and discuss future work. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Self-reported confidence in patient safety knowledge among Australian undergraduate nursing students: A multi-site cross-sectional survey study.

Science.gov (United States)

Usher, Kim; Woods, Cindy; Parmenter, Glenda; Hutchinson, Marie; Mannix, Judy; Power, Tamara; Chaboyer, Wendy; Latimer, Sharon; Mills, Jane; Siegloff, Lesley; Jackson, Debra

2017-06-01

Patient safety is critical to the provision of quality health care and thus is an essential component of nurse education. To describe first, second and third year Australian undergraduate nursing students' confidence in patient safety knowledge acquired in the classroom and clinical settings across the three years of the undergraduate nursing program. A cross-sectional online survey conducted in 2015. Seven Australian universities with campuses across three states (Queensland, New South Wales, South Australia). A total of 1319 Australian undergraduate nursing students. Participants were surveyed using the 31-item Health Professional Education in Patient Safety Survey (H-PEPSS). Descriptive statistics summarised the sample and survey responses. Paired t-tests, ANOVA and generalized-estimating-equations models were used to compare responses across learning settings (classroom and clinical), and year of nursing course. Participants were most confident in their learning of clinical safety skills and least confident in learning about the sociocultural dimensions of working in teams with other health professionals, managing safety risks and understanding human and environmental factors. Only 59% of students felt confident they could approach someone engaging in unsafe practice, 75% of students agreed it was difficult to question the decisions or actions of those with more authority, and 78% were concerned they would face disciplinary action if they made a serious error. One patient safety subscale, Recognising and responding to remove immediate safety risks, was rated significantly higher by third year nursing students than by first and second year students. Two broader aspects of patient safety scales, Consistency in how patient safety issues are dealt with by different preceptors, and System aspects of patient safety are well covered in our program, were rated significantly higher by first year nursing students than by second and third year students. One scale

Web of Things-Based Remote Monitoring System for Coal Mine Safety Using Wireless Sensor Network

OpenAIRE

Bo, Cheng; Xin, Cheng; Zhongyi, Zhai; Chengwen, Zhang; Junliang, Chen

2014-01-01

Frequent accidents have occurred in coal mine enterprises; therefore, raising the technological level of coal mine safety monitoring systems is an urgent problem. Wireless sensor networks (WSN), as a new field of research, have broad application prospects. This paper proposes a Web of Things- (WoT-) based remote monitoring system that takes full advantage of wireless sensor networks in combination with the CAN bus communication technique that abstracts the underground sensor data and capabili...

Applications of ZigBee Technology in the Safety Monitoring System of Low Gas Pipeline Transportation

Directory of Open Access Journals (Sweden)

Wei Deyu

2015-01-01

Full Text Available The existing safety monitoring system of low gas pipeline transportation establishes a wired communication network monitoring system mainly on the basis of industrial bus. It has problems such as large transmission signal attenuation, complex wiring, high-labor intensity, inconvenient installation and maintenance, high maintenance cost, and so on. Featuring low cost, power-saving, reliability, stability and flexibility, the wireless sensor network established by ZigBee wireless communication technology can realize the real-time all-dimensional dynamic monitoring on parameters of low gas pipeline transportation system and overcome the shortcomings and deficiencies of wired network system.

Catalogue of systems for the monitoring of working conditions relating to health and safety

NARCIS (Netherlands)

Prins, R.; Verboon, F.

1991-01-01

In this Catalogue a number of systems or instruments for Monitoring Working Conditions and workers Health and Safety have been described. The general aim of the project was three-fold: - to obtain an overall assessment of the existing instruments for identifying risk factors and working conditions

The comparison of road safety survey answers between web-panel and face-to-face : Dutch results of SARTRE-4 survey.

NARCIS (Netherlands)

Goldenbeld, C. & Craen, S. de

2013-01-01

In The Netherlands, a comparison of an online and a face-to-face sample of car drivers was made to study differences on a number of selected questions from the SARTRE-4 road safety survey. Contrary to expectations, there was no indication that online respondents were more likely to come from higher

Topical session proceedings of the 6. IGSC Meeting. The role of monitoring in a safety case

International Nuclear Information System (INIS)

2005-01-01

This report summarises the outcomes of a topical session focused on the role of monitoring in a safety case. It was held as part of the 6. plenary meeting of the IGSC. It was attended by 39 participants, representing waste management organisations and regulatory authorities from 15 NEA member countries, the IAEA and the European Commission. The main purpose of this topical session was to create a platform for exchanging views on the key monitoring issues of interest to build confidence in a safety case e.g. relationship with the post-closure phase, functions, requirements, and to determine to what extent the main actions are to be addressed by the IGSC on its ongoing activities on defining the elements of a safety case. The topical session was indeed mainly aimed at exchanging information on: - National strategies or programmes in NEA members' countries. Member countries have organisations planning their own strategy, but some are already, to some extend engaged in implementing monitoring activities, e.g. Posiva Oy, US-DOE-YM, Andra. - Feedback from international projects, e.g. the EC Thematic Network on 'The role of Monitoring in a Phased Approach to Geological Disposal of Radioactive Waste', and the IAEA programme of work. - The expectations of regulators, e.g. SKI. Part A of this document summarises the material orally presented and provides the main lessons drawn from the presentations and the discussions that followed them. The overheads presented are compiled without any further elaboration by the NEA Secretariat as Part B of the document. Part C gives the list of participants. The document as a whole provides a synthesis of current issues in monitoring of a deep geological disposal facility

The adaptive safety analysis and monitoring system

Science.gov (United States)

Tu, Haiying; Allanach, Jeffrey; Singh, Satnam; Pattipati, Krishna R.; Willett, Peter

2004-09-01

The Adaptive Safety Analysis and Monitoring (ASAM) system is a hybrid model-based software tool for assisting intelligence analysts to identify terrorist threats, to predict possible evolution of the terrorist activities, and to suggest strategies for countering terrorism. The ASAM system provides a distributed processing structure for gathering, sharing, understanding, and using information to assess and predict terrorist network states. In combination with counter-terrorist network models, it can also suggest feasible actions to inhibit potential terrorist threats. In this paper, we will introduce the architecture of the ASAM system, and discuss the hybrid modeling approach embedded in it, viz., Hidden Markov Models (HMMs) to detect and provide soft evidence on the states of terrorist network nodes based on partial and imperfect observations, and Bayesian networks (BNs) to integrate soft evidence from multiple HMMs. The functionality of the ASAM system is illustrated by way of application to the Indian Airlines Hijacking, as modeled from open sources.

Safety as experienced by patients themselves: a Finnish survey of the most recent period of care.

Science.gov (United States)

Sahlström, Merja; Partanen, Pirjo; Turunen, Hannele

2014-06-01

We examined patients' experiences of patient safety and participation in promoting safe care during their most recent care period. A survey of patients (N = 175) revealed that treatment, medication, and device safety were mostly experienced as very good or excellent, but responses varied by age and experience. Patients ages 66-75 were most critical of treatment and medication safety. Device safety was rated the worst aspect of safety. Twenty percent of respondents had experienced errors at some time during their care. Patients who had experienced errors and those who were treated at inpatient wards versus a day surgery unit were most critical towards patient participation. Open and transparent error management involving patients is needed to promote treatment, medication, and especially device safety. © 2014 Wiley Periodicals, Inc.

Mobile acoustic transects miss rare bat species: implications of survey method and spatio-temporal sampling for monitoring bats

Directory of Open Access Journals (Sweden)

Elizabeth C. Braun de Torrez

2017-11-01

Full Text Available Due to increasing threats facing bats, long-term monitoring protocols are needed to inform conservation strategies. Effective monitoring should be easily repeatable while capturing spatio-temporal variation. Mobile acoustic driving transect surveys (‘mobile transects’ have been touted as a robust, cost-effective method to monitor bats; however, it is not clear how well mobile transects represent dynamic bat communities, especially when used as the sole survey approach. To assist biologists who must select a single survey method due to resource limitations, we assessed the effectiveness of three acoustic survey methods at detecting species richness in a vast protected area (Everglades National Park: (1 mobile transects, (2 stationary surveys that were strategically located by sources of open water and (3 stationary surveys that were replicated spatially across the landscape. We found that mobile transects underrepresented bat species richness compared to stationary surveys across all major vegetation communities and in two distinct seasons (dry/cool and wet/warm. Most critically, mobile transects failed to detect three rare bat species, one of which is federally endangered. Spatially replicated stationary surveys did not estimate higher species richness than strategically located stationary surveys, but increased the rate at which species were detected in one vegetation community. The survey strategy that detected maximum species richness and the highest mean nightly species richness with minimal effort was a strategically located stationary detector in each of two major vegetation communities during the wet/warm season.

Mobile acoustic transects miss rare bat species: implications of survey method and spatio-temporal sampling for monitoring bats.

Science.gov (United States)

Braun de Torrez, Elizabeth C; Wallrichs, Megan A; Ober, Holly K; McCleery, Robert A

2017-01-01

Due to increasing threats facing bats, long-term monitoring protocols are needed to inform conservation strategies. Effective monitoring should be easily repeatable while capturing spatio-temporal variation. Mobile acoustic driving transect surveys ('mobile transects') have been touted as a robust, cost-effective method to monitor bats; however, it is not clear how well mobile transects represent dynamic bat communities, especially when used as the sole survey approach. To assist biologists who must select a single survey method due to resource limitations, we assessed the effectiveness of three acoustic survey methods at detecting species richness in a vast protected area (Everglades National Park): (1) mobile transects, (2) stationary surveys that were strategically located by sources of open water and (3) stationary surveys that were replicated spatially across the landscape. We found that mobile transects underrepresented bat species richness compared to stationary surveys across all major vegetation communities and in two distinct seasons (dry/cool and wet/warm). Most critically, mobile transects failed to detect three rare bat species, one of which is federally endangered. Spatially replicated stationary surveys did not estimate higher species richness than strategically located stationary surveys, but increased the rate at which species were detected in one vegetation community. The survey strategy that detected maximum species richness and the highest mean nightly species richness with minimal effort was a strategically located stationary detector in each of two major vegetation communities during the wet/warm season.

Survey of environment related monitoring programmes of international organizations and their contribution to international monitoring programmes

International Nuclear Information System (INIS)

1986-12-01

The report is a summary of environment-related monitoring programmes of international governmental organizations and their contribution to international monitoring programmes. it presents the situation as of November 1986: This survey has been prepared by a consultant for the Secretariat as a background document for the second meeting of the Environment Experts, Economic Summit in Munich, November 1986. It serves information purposes only. No claim for completeness is intended. This report may also prove to be helpful for administrators and the scientific community as regards gaining knowledge on present arrangements, approaches and environmental activities in the framework of international organizations. In this light, the present report could facilitate communication and progress in solving pressing environmental problems on the international level. (orig.)

Development of Information Support of the Automated System for Monitoring the State of the Gas Transportation System’s Industrial Safety

Directory of Open Access Journals (Sweden)

Ruslan Skrynkovskyy

2017-08-01

Full Text Available The purpose of the article is to developing the information security of the automated system for monitoring the state of industrial safety of the gas transportation system within the framework of the safety management system, which will enable timely and objective detection of adverse accident hazards (hazardous events and taking the necessary specific measures to eliminate them and operate the gas transport system safely. It is proved that the basis of the information provision of the automated system for monitoring the state of the industrial safety of the gas transmission system is a methodology that includes the following basic procedures: identifying hazards; qualitative and quantitative assessment of emergencies; establishing of unacceptable (unallowable risks and their introduction to the information base (register of unacceptable risks of objects of the gas transportation system; comprehensive assessment and certification of the state of industrial safety of objects of the gas transportation system; identification of effective, productive (efficient risk management measures. The prospect of further research in this area is the development and implementation of an automated system for monitoring the state of industrial safety of the objects of the gas transmission system based on the results of the research (of the submitted information provision.

Breast Ultrasound Examination with Video Monitor System: A Satisfaction Survey among Patients

International Nuclear Information System (INIS)

Ryu, Jung Kyu; Kim, Hyun Cheol; Yang, Dal Mo

2010-01-01

The purpose of this study is to assess the patients satisfaction with a newly established video-monitor system and the associated basic items for performing breast ultrasound exams by conducting a survey among the patients. 349 patients were invited to take the survey and they had undergone breast ultrasound examination once during the 3 months after the monitor system has been introduced. The questionnaire was composed of 8 questions, 4 of which were about the basic items such as age, gender and the reason of their taking the breast ultrasound exam, their preference for the gender of the examiner and the desired length of time for the examination. The other 4 question were about their satisfaction with the video monitor. The patients were divided into two groups according to the purposes of taking the exams, which were screening or diagnostic purposes. The results were compared between these 2 groups. The satisfaction with the video monitor system was assessed by using a scoring system that ranged from 1 to 5. For the total patients, the screening group was composed of 124 patients and the diagnostic group was composed of 225. The reasons why the patients wanted to take the examinations in the diagnostic group varied. The questionnaire about the preference of the gender of the examiner showed that 81.5% in the screening group and 79.1% in the diagnostic group preferred a woman doctor. The required, suitable time for the breast ultrasound examination was 5 to 10 minutes or 10 to 15 minutes for about 70% of the patients. The mean satisfaction score for the video monitor system was as high as 3.95 point. The portion of patients in each group who answered over 3 points for their satisfaction with the monitor system was 88.7% and 94.2%, respectively. Our study showed that patients preferred 5-15 minutes for the length of the examination time and a female examiner. We also confirmed high patient satisfaction with the video monitor system

Breast Ultrasound Examination with Video Monitor System: A Satisfaction Survey among Patients

Energy Technology Data Exchange (ETDEWEB)

Ryu, Jung Kyu; Kim, Hyun Cheol; Yang, Dal Mo [East-West Neo Medical Center, Kyung-Hee University, Seoul (Korea, Republic of)

2010-03-15

The purpose of this study is to assess the patients satisfaction with a newly established video-monitor system and the associated basic items for performing breast ultrasound exams by conducting a survey among the patients. 349 patients were invited to take the survey and they had undergone breast ultrasound examination once during the 3 months after the monitor system has been introduced. The questionnaire was composed of 8 questions, 4 of which were about the basic items such as age, gender and the reason of their taking the breast ultrasound exam, their preference for the gender of the examiner and the desired length of time for the examination. The other 4 question were about their satisfaction with the video monitor. The patients were divided into two groups according to the purposes of taking the exams, which were screening or diagnostic purposes. The results were compared between these 2 groups. The satisfaction with the video monitor system was assessed by using a scoring system that ranged from 1 to 5. For the total patients, the screening group was composed of 124 patients and the diagnostic group was composed of 225. The reasons why the patients wanted to take the examinations in the diagnostic group varied. The questionnaire about the preference of the gender of the examiner showed that 81.5% in the screening group and 79.1% in the diagnostic group preferred a woman doctor. The required, suitable time for the breast ultrasound examination was 5 to 10 minutes or 10 to 15 minutes for about 70% of the patients. The mean satisfaction score for the video monitor system was as high as 3.95 point. The portion of patients in each group who answered over 3 points for their satisfaction with the monitor system was 88.7% and 94.2%, respectively. Our study showed that patients preferred 5-15 minutes for the length of the examination time and a female examiner. We also confirmed high patient satisfaction with the video monitor system

Nursing home safety: does financial performance matter?

Science.gov (United States)

Oetjen, Reid M; Zhao, Mei; Liu, Darren; Carretta, Henry J

2011-01-01

This study examines the relationship between financial performance and selected safety measures of nursing homes in the State of Florida. We used descriptive analysis on a total sample of 1,197. Safety information was from the Online Survey, Certification and Reporting (OSCAR) data of 2003 to 2005, while the financial performance measures were from the Medicare cost reports of 2002 to 2004. Finally, we examined the most frequently cited deficiencies as well as the relationship between financial performance and quality indicators. Nursing homes in the bottom quartile of financial performance perform poorly on most resident-safety measures of care; however, nursing homes in the top two financial categories also experienced a higher number of deficiencies. Nursing homes in the next to lowest quartile of financial performance category best perform on most of these safety measures. The results reinforce the need to monitor nursing home quality and resident safety in US nursing homes, especially among facilities with poor overall financial performance.

National young-driver survey: teen perspective and experience with factors that affect driving safety.

Science.gov (United States)

Ginsburg, Kenneth R; Winston, Flaura K; Senserrick, Teresa M; García-España, Felipe; Kinsman, Sara; Quistberg, D Alex; Ross, James G; Elliott, Michael R

2008-05-01

Motor vehicle crashes are the leading cause of fatality and acquired disability in adolescents. Young, inexperienced drivers are overrepresented in crashes. Our goal was to explore the adolescent perspective on driving safety to provide a better understanding of factors that influence safety and teenagers' exposure to driving hazards. Adolescents generated, prioritized, and explained their viewpoint by using the teen-centered method. These viewpoints were obtained from a school-based nationally representative survey of 9th-, 10th-, and 11th-graders (N = 5665) from 68 high schools, conducted in spring 2006, that included teen-generated items. The main outcome measures were rating of risk and prevalence of witnessing driving hazards. Drinking while driving was ranked as the greatest hazard (87% of the respondents reported that it made a lot of difference), although only 12% witnessed it often. Ranked next as dangers while driving were text-messaging, racing, impairment from marijuana, and road rage. Sixty percent viewed inexperience as a significant hazard, although only 15% reported seeing it often. Cell phone use was viewed as a significant hazard by 28%, although 57% witnessed it frequently. Only 10% viewed peer passengers as hazardous, but 64% frequently observed them. Distracting peer behaviors, among other distractions, were viewed as more dangerous. Subpopulations varied in the degree they perceived hazards. For example, black and Hispanic adolescents viewed substance use while driving as less hazardous than did white adolescents but witnessed it more frequently. Adolescents generally understand the danger of intoxicated driving. However, some groups need to better recognize this hazard. Distractions take teenagers' focus off the road, but not all are viewed as hazardous. Although inexperience is the key factor that interacts with other conditions to cause crashes, adolescents do not recognize what merits experience. Future research is needed to explore how to

Motorcycle Safety Education Programs: Report of a Survey of State Departments of Education and of Colleges and Universities.

Science.gov (United States)

American Driver and Traffic Safety Education Association, Washington, DC.

A survey of State departments of education and colleges and universities, conducted by the Motorcycle Industry Council Safety and Education Foundation, revealed the need for more teacher education programs, instructional materials, and organized workshops that promote motorcycle safety education. The primary interest indicated by State departments…

Behavioral integrity for safety, priority of safety, psychological safety, and patient safety : a team-level study

NARCIS (Netherlands)

Leroy, H.; Dierynck, B.; Anseel, F.; Simons, T.; Halbesleben, J.R.; McCaughey, D.; Savage, G.T.; Sels, L.

2012-01-01

This article clarifies how leader behavioral integrity for safety helps solve follower's double bind between adhering to safety protocols and speaking up about mistakes against protocols. Path modeling of survey data in 54 nursing teams showed that head nurse behavioral integrity for safety

Measurement and monitoring of safety: impact and challenges of putting a conceptual framework into practice.

Science.gov (United States)

Chatburn, Eleanor; Macrae, Carl; Carthey, Jane; Vincent, Charles

2018-03-06

The Measurement and Monitoring of Safety Framework provides a conceptual model to guide organisations in assessing safety. The Health Foundation funded a large-scale programme to assess the value and impact of applying the Framework in regional and frontline care settings. We explored the experiences and reflections of key participants in the programme. The study was conducted in the nine healthcare organisations in England and Scotland testing the Framework (three regional improvement bodies, six frontline settings). Post hoc interviews with clinical and managerial staff were analysed using template analysis. Participants reported that the Framework promoted a substantial shift in their thinking about how safety is actively managed in their environment. It provided a common language, facilitated a more inquisitive approach and encouraged a more holistic view of the components of safety. These changes in conceptual understanding, however, did not always translate into broader changes in practice, with many sites only addressing some aspects of the Framework. One of the three regions did embrace the Framework in its entirety and achieved wider impact with a range of interventions. This region had committed leaders who took time to fully understand the concepts, who maintained a flexible approach to exploring the utility of the Framework and who worked with frontline staff to translate the concepts for local settings. The Measuring and Monitoring of Safety Framework has the potential to support a broader and richer approach to organisational safety. Such a conceptually based initiative requires both committed leaders who themselves understand the concepts and more time to establish understanding and aims than might be needed in a standard improvement programme. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Monitoring visitor satisfaction: a comparison of comment cards and more in-depth surveys

Science.gov (United States)

Alan R. Graefe; James D. Absher; Robert C. Burns

2001-01-01

This paper compares responses to comment cards and more detailed on-site surveys at selected Corps of Engineers lakes. The results shed light on the validity, reliability, and usefulness of these alternative methods of monitoring customer satisfaction.

Radiological safety system based on real-time tritium-in-air monitoring in room and effluents

Energy Technology Data Exchange (ETDEWEB)

Bidica, N.; Sofalca, N.; Balteanu, O.; Stefan, I. [National Institute of Cryogenics and Isotopes Technologies, Ramnicu Valcea (Romania)

2006-07-01

The conceptual design of the radiological safety system based on real time-in-air monitoring in room and effluents is intended to provide the maximum achievable safety level, basing no the ALARA concept. the capabilities of this system are not only to inform any time personnel about tritium in air concentration level, but it will be able to: initiate the shut down procedure and drain off the plant, as well to start the Air cleaning System when the tritium-in-air concentration exceed pre-established threshold; estimate tritium effective dose rate before starting an activity into the monitored area, or during this activity, or soon as the activity was finished; estimate tritium effective dose and instantly record and update individual effective doses, using a special computer application called 'dose record'; lock access into the radiological area for individuals when tritium dose rate in the monitoring area will exceed the pre-established thresholds, or when any individual dose data provided by 'dose records' application ask for, or for other protection consideration; calculate the total tritium activity released to the environment (per day, week, or month). (N.C.)

Radiological safety system based on real-time tritium-in-air monitoring in room and effluents

International Nuclear Information System (INIS)

Bidica, N.; Sofalca, N.; Balteanu, O.; Stefan, I.

2006-01-01

The conceptual design of the radiological safety system based on real time-in-air monitoring in room and effluents is intended to provide the maximum achievable safety level, basing no the ALARA concept. the capabilities of this system are not only to inform any time personnel about tritium in air concentration level, but it will be able to: initiate the shut down procedure and drain off the plant, as well to start the Air cleaning System when the tritium-in-air concentration exceed pre-established threshold; estimate tritium effective dose rate before starting an activity into the monitored area, or during this activity, or soon as the activity was finished; estimate tritium effective dose and instantly record and update individual effective doses, using a special computer application called 'dose record'; lock access into the radiological area for individuals when tritium dose rate in the monitoring area will exceed the pre-established thresholds, or when any individual dose data provided by 'dose records' application ask for, or for other protection consideration; calculate the total tritium activity released to the environment (per day, week, or month). (N.C.)

Renal studies in safety pharmacology and toxicology: A survey conducted in the top 15 pharmaceutical companies.

Science.gov (United States)

Benjamin, Amanda; Gallacher, David J; Greiter-Wilke, Andrea; Guillon, Jean-Michel; Kasai, Cheiko; Ledieu, David; Levesque, Paul; Prelle, Katja; Ratcliffe, Sian; Sannajust, Frederick; Valentin, Jean-Pierre

2015-01-01

With the recent development of more sensitive biomarkers to assess kidney injury preclinically, a survey was designed i) to investigate what strategies are used to investigate renal toxicity in both ICH S7A compliant Safety Pharmacology (SP) studies after a single dose of a compound and within repeat-dose toxicity studies by large pharmaceutical companies today; ii) to understand whether renal SP studies have impact or utility in drug development and/or if it may be more appropriate to assess renal effects after multiple doses of compounds; iii) to ascertain how much mechanistic work is performed by the top 15 largest pharmaceutical companies (as determined by R&D revenue size); iv) to gain an insight into the impact of the validation of DIKI biomarkers and their introduction in the safety evaluation paradigm; and v) to understand the impact of renal/urinary safety study data on progression of projects. Two short anonymous surveys were submitted to SP leaders of the top 15 pharmaceutical companies, as defined by 2012 R&D portfolio size. Fourteen multiple choice questions were designed to explore the strategies used to investigate renal effects in both ICH S7A compliant SP studies and within toxicology studies. A 67% and 60% response rate was obtained in the first and second surveys, respectively. Nine out of ten respondent companies conduct renal excretory measurements (eg. urine analysis) in toxicology studies whereas only five out of ten conduct specific renal SP studies; and all of those 5 also conduct the renal excretory measurements in toxicology studies. These companies measure and/or calculate a variety of parameters as part of these studies, and also on a case by case basis include regulatory qualified and non-qualified DIKI biomarkers. Finally, only one company has used renal/urinary functional data alone to stop a project, whereas the majority of respondents combine renal data with other target organ assessments to form an integrated decision-making set

Monitoring survey of pulsating giant stars in the Local Group galaxies: survey description, science goals, target selection

International Nuclear Information System (INIS)

Saremi, E; Abedi, A; Javadi, A; Khosroshahi, H; Molaei Nezhad, A; Van Loon, J Th; Bamber, J; Hashemi, S A; Nikzat, F

2017-01-01

The population of nearby dwarf galaxies in the Local Group constitutes a complete galactic environment, perfect suited for studying the connection between stellar populations and galaxy evolution. In this study, we are conducting an optical monitoring survey of the majority of dwarf galaxies in the Local Group, with the Isaac Newton Telescope (INT), to identify long period variable stars (LPVs). These stars are at the end points of their evolution and therefore their luminosity can be directly translated into their birth masses; this enables us to reconstruct the star formation history. By the end of the monitoring survey, we will have performed observations over ten epochs, spaced approximately three months apart, and identified long-period, dust-producing AGB stars; five epochs of data have been obtained already. LPVs are also the main source of dust; in combination with Spitzer Space Telescope images at mid-IR wavelengths we will quantify the mass loss, and provide a detailed map of the mass feedback into the interstellar medium. We will also use the amplitudes in different optical passbands to determine the radius variations of the stars, and relate this to their mass loss. (paper)

Monitoring survey of pulsating giant stars in the Local Group galaxies: survey description, science goals, target selection

Science.gov (United States)

Saremi, E.; Javadi, A.; van Loon, J. Th; Khosroshahi, H.; Abedi, A.; Bamber, J.; Hashemi, S. A.; Nikzat, F.; Molaei Nezhad, A.

2017-06-01

The population of nearby dwarf galaxies in the Local Group constitutes a complete galactic environment, perfect suited for studying the connection between stellar populations and galaxy evolution. In this study, we are conducting an optical monitoring survey of the majority of dwarf galaxies in the Local Group, with the Isaac Newton Telescope (INT), to identify long period variable stars (LPVs). These stars are at the end points of their evolution and therefore their luminosity can be directly translated into their birth masses; this enables us to reconstruct the star formation history. By the end of the monitoring survey, we will have performed observations over ten epochs, spaced approximately three months apart, and identified long-period, dust-producing AGB stars; five epochs of data have been obtained already. LPVs are also the main source of dust; in combination with Spitzer Space Telescope images at mid-IR wavelengths we will quantify the mass loss, and provide a detailed map of the mass feedback into the interstellar medium. We will also use the amplitudes in different optical passbands to determine the radius variations of the stars, and relate this to their mass loss.

Safety Evaluation of an Automated Remote Monitoring System for Heart Failure in an Urban, Indigent Population.

Science.gov (United States)

Gross-Schulman, Sandra; Sklaroff, Laura Myerchin; Hertz, Crystal Coyazo; Guterman, Jeffrey J

2017-12-01

Heart Failure (HF) is the most expensive preventable condition, regardless of patient ethnicity, race, socioeconomic status, sex, and insurance status. Remote telemonitoring with timely outpatient care can significantly reduce avoidable HF hospitalizations. Human outreach, the traditional method used for remote monitoring, is effective but costly. Automated systems can potentially provide positive clinical, fiscal, and satisfaction outcomes in chronic disease monitoring. The authors implemented a telephonic HF automated remote monitoring system that utilizes deterministic decision tree logic to identify patients who are at risk of clinical decompensation. This safety study evaluated the degree of clinical concordance between the automated system and traditional human monitoring. This study focused on a broad underserved population and demonstrated a safe, reliable, and inexpensive method of monitoring patients with HF.

Voices of nuclear power monitors in fiscal 1982

International Nuclear Information System (INIS)

1984-01-01

The system of nuclear power monitors was set up to hear candid opinions, etc. from general people on nuclear power development and utilization, and reflect them to nuclear power administration. As the monitors, 416 persons were selected across the country. The results in fiscal 1982 are described. (1) Questionnaire survey: Of the 416, 314 persons answered the questionnaire conducted in March, 1983, on future energy, nuclear power development, nuclear power safety administration, and nuclear power P.R. activities. (2) Occasional voices of monitors: Of the total 74 opinions, etc. from the monitors in fiscal 1982, 31 concerned the nuclear power P.R. activities, followed by 16 on nuclear power development and utilization, and 12 on nuclear power administration. (Mori, K.)

Configuration of risk monitor system by plant defense-in-depth risk monitor and reliability monitor

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Lind Morten; Yang Ming; Hashim Muhammad; Zhang Zhijian

2012-01-01

A new method of risk monitor system of a nuclear power plant has been proposed from the aspect by what degree of safety functions incorporated in the plant system is maintained by multiple barriers of defense-in-depth (DiD). Wherein, the central idea is plant DiD risk monitor and reliability monitor derived from the five aspects of (1) design principle of nuclear safety based on DiD concept, (2) definition of risk and risk to be monitored, (3) severe accident phenomena as major risk, (4) scheme of risk ranking, and (5) dynamic risk display. In this paper, the overall frame of the proposed risk monitor system is summarized and the detailed discussion is made on major items such as definition of risk and risk ranking, anatomy of fault occurrence, two-layer configuration of risk monitor, how to configure individual elements of plant DiD risk monitor, and lastly how to apply for a PWR safety system. (author)

Satellite synthetic aperture radar for monitoring of surface deformation in shallow underground mining environments

CSIR Research Space (South Africa)

Engelbrecht, J

2016-08-01

Full Text Available . There are also human health-and-safety concerns in potentially unstable areas. To monitor the extent of deforming areas over time, ground-based surveys, including GPS and spirit-levelling techniques, are frequently employed. However, the process is time...

The study on safety facility criteria for radioactive waste repository

International Nuclear Information System (INIS)

Lee, S. H.; Choi, M. H.; Han, S. H. and others

1992-12-01

The radioactive waste repository are necessary to install the engineered safety systems to secure the safety for operation of the repository in the event of fire and earthquake. Since the development of safety facility criteria requires a thorough understanding about the characteristics of the engineered safety systems, we should investigate by means of literature survey and visit SKB. In particular, definition, composition of the systems, functional requirement of the systems, engineered safety systems of foreign countries, system design, operation and maintenance requirement should be investigated : fire protection system, ventilation system, drainage system, I and C system, electric system, radiation monitoring system. This proposed criteria consist of purpose, scope of application, ventilation system, fire protection system, drainage system, electric system and this proposed criteria can be applied as a basic reference for the final criteria

Development of a patient safety climate survey for Chinese hospitals: cross-national adaptation and psychometric evaluation.

Science.gov (United States)

Zhu, Junya; Li, Liping; Zhao, Hailei; Han, Guangshu; Wu, Albert W; Weingart, Saul N

2014-10-01

Existing patient safety climate instruments, most of which have been developed in the USA, may not accurately reflect the conditions in the healthcare systems of other countries. To develop and evaluate a patient safety climate instrument for healthcare workers in Chinese hospitals. Based on a review of existing instruments, expert panel review, focus groups and cognitive interviews, we developed items relevant to patient safety climate in Chinese hospitals. The draft instrument was distributed to 1700 hospital workers from 54 units in six hospitals in five Chinese cities between July and October 2011, and 1464 completed surveys were received. We performed exploratory and confirmatory factor analyses and estimated internal consistency reliability, within-unit agreement, between-unit variation, unit-mean reliability, correlation between multi-item composites, and association between the composites and two single items of perceived safety. The final instrument included 34 items organised into nine composites: institutional commitment to safety, unit management support for safety, organisational learning, safety system, adequacy of safety arrangements, error reporting, communication and peer support, teamwork and staffing. All composites had acceptable unit-mean reliabilities (≥0.74) and within-unit agreement (Rwg ≥0.71), and exhibited significant between-unit variation with intraclass correlation coefficients ranging from 9% to 21%. Internal consistency reliabilities ranged from 0.59 to 0.88 and were ≥0.70 for eight of the nine composites. Correlations between composites ranged from 0.27 to 0.73. All composites were positively and significantly associated with the two perceived safety items. The Chinese Hospital Survey on Patient Safety Climate demonstrates adequate dimensionality, reliability and validity. The integration of qualitative and quantitative methods is essential to produce an instrument that is culturally appropriate for Chinese hospitals

Overcoming regulatory challenges in the development of companion diagnostics for monitoring and safety.

Science.gov (United States)

Shimazawa, Rumiko; Ikeda, Masayuki

2016-03-01

Concurrent development and co-approval of a companion diagnostic (CDx) with a corresponding drug is ideal, but often unfeasible. Because of limited exposure to a drug in clinical trials, crucial information on safety is sometimes revealed only after approval. Therefore, a CDx for monitoring/safety is often developed after approval of a corresponding drug. However, regulatory guidance is insufficient if contemporaneous development is not possible, thereby leaving plenty of opportunities for improvement with respect to pharmacovigilance and retrospective validation of the CDx. Furthermore, global harmonization of guidance on how to incorporate new scientific information from retrospective analyses of biomarkers should lead to the establishment of more evidence for the development of CDx for approved drugs.

Assessment of the global trigger tool to measure, monitor and evaluate pateint safety in cancer patients

DEFF Research Database (Denmark)

Otto Mattsson, Thea; Lehmann-Knudsen, Janne; Lauritsen, Jens M

2013-01-01

BACKGROUND: Countries around the world are currently aiming to improve patient safety by means of the Institute for Healthcare Improvement global trigger tool (GTT), which is considered a valid tool for evaluating and measuring patient safety within organisations. So far, only few data....... RESULTS: Only 31% of adverse events (AE) were identified by both teams, and further differences in categorisation of identical events was found. Moderate interrater agreement (κ=0.45) between teams gave rise to different conclusions on the patient safety process when monitoring using SPC charts. The Bland......-Altman plot suggests little systematic error but large random error. CONCLUSIONS: Review teams may identify different AE and reach different conclusions on the safety process when using the GTT on identical charts. Tracking true change in the safety level is difficult due to measurement error of the GTT...

Environmental monitoring activities in JAERI at JCO accident

International Nuclear Information System (INIS)

Yamaguchi, Takenori

2001-01-01

The Japan Atomic Energy Research Institute (JAERI) was involved in a various environmental monitoring activities, such as environmental radiation monitoring by monitoring post and monitoring car, air dust, soil, green vegetables and water sampling and measurements, neutron and gamma radiation dose rate survey around the JCO site for emergency response actions to the JCO accident on September 30, 1999. These activities were performed from Sep. 30 to Oct. 2, and were the initial and first stage activities in the emergency environmental monitoring activities. JAERI has been assigned to the public organization to support the government by Disaster Prevention Fundamental Law. These activities were performed to ensure the public safety to avoid the effluent of the accident. Through the environmental monitoring activities, I recognized that the importance of the accident information to make the best use for the initial environmental monitoring, and the monitoring information exchange is important to perform the effective monitoring activities for taking the early countermeasures such as evacuation to the public. (author)

Exploring relationships between hospital patient safety culture and Consumer Reports safety scores.

Science.gov (United States)

Smith, Scott Alan; Yount, Naomi; Sorra, Joann

2017-02-16

A number of private and public companies calculate and publish proprietary hospital patient safety scores based on publicly available quality measures initially reported by the U.S. federal government. This study examines whether patient safety culture perceptions of U.S. hospital staff in a large national survey are related to publicly reported patient safety ratings of hospitals. The Agency for Healthcare Research and Quality Hospital Survey on Patient Safety Culture (Hospital SOPS) assesses provider and staff perceptions of hospital patient safety culture. Consumer Reports (CR), a U.S. based non-profit organization, calculates and shares with its subscribers a Hospital Safety Score calculated annually from patient experience survey data and outcomes data gathered from federal databases. Linking data collected during similar time periods, we analyzed relationships between staff perceptions of patient safety culture composites and the CR Hospital Safety Score and its five components using multiple multivariate linear regressions. We analyzed data from 164 hospitals, with patient safety culture survey responses from 140,316 providers and staff, with an average of 856 completed surveys per hospital and an average response rate per hospital of 56%. Higher overall Hospital SOPS composite average scores were significantly associated with higher overall CR Hospital Safety Scores (β = 0.24, p Consumer Reports Hospital Safety Score, which is a composite of patient experience and outcomes data from federal databases. As hospital managers allocate resources to improve patient safety culture within their organizations, their efforts may also indirectly improve consumer-focused, publicly reported hospital rating scores like the Consumer Reports Hospital Safety Score.

Systems for the monitoring of working conditions relating to health and safety : extensive descriptions : Belgium, Germany, Luxembourg, The Netherlands

NARCIS (Netherlands)

Prins, R.; Verboon, F.

1991-01-01

This report contains the extensive descriptions of (some of) the monitoring systems on health and safety in use in the Benelux countries and Germany. The project of which this report is a part aimed at gathering information on monitoring systems throughout the EC member states.

Current Trends in Neuromuscular Blockade, Management, and Monitoring amongst Singaporean Anaesthetists

Directory of Open Access Journals (Sweden)

Wendy H. Teoh

2016-01-01

Full Text Available Introduction. This survey aimed to investigate the attitudes/practice pertaining the use, management, and monitoring of neuromuscular blockade amongst Singaporean anaesthetists. Methods. All specialist accredited anaesthetists registered with the Singapore Medical Council were invited to complete an anonymous online survey. Results. The response rate was 39.5%. Neuromuscular monitoring (NM was used routinely by only 13.1% despite the widespread availability of monitors. 82% stated residual NMB (RNMB was a significant risk factor for patient outcome, but only 24% believed NMB monitoring should be compulsory in all paralyzed patients. 63.6% of anaesthetists estimated the risk of RNMB in their own institutions to be 50% said such benefits may be able to offset the associated costs. Conclusions. There is a significant need for reeducation about RNMB, studies on local RNMB incidences, and strengthening of current monitoring practices and guidelines. Strategies are discussed. As NM monitors appear widely available and reversal of NMB standard practice, it is hopeful that Singaporean anaesthetists will change and strive for evidence-based best clinical practice to enhance patient safety.

Report of radioactivity survey research in fiscal year 1989

International Nuclear Information System (INIS)

1990-12-01

In the National Institute of Radiological Sciences, as a part of the radioactivity survey and research of Science and Technology Agency, the survey of environmental radioactivity level due to the radioactive fallout accompanying nuclear explosion experiments and the radioactive substances released from nuclear facilities and others and the safety analysis of these have been carried out. The radioactivity and dose survey for environment, foods and human bodies, the survey of the level around nuclear facilities, the business of radioactivity data center, the basic investigation for the evaluation of the results of radioactivity survey, the training of environmental radiation monitoring technicians and the investigation and research of the measurement of emergency radiation exposure and countermeasures were carried out. Those results are summarized. (K.I.)

Implementation of the surgical safety checklist in Switzerland and perceptions of its benefits: cross-sectional survey.

Directory of Open Access Journals (Sweden)

Stéphane Cullati

Full Text Available OBJECTIVES: To examine the implementation of the Surgical Safety Checklist (SSC among surgeons and anaesthetists working in Swiss hospitals and clinics and their perceptions of the SSC. METHODS: Cross-sectional survey at the 97th Annual Meeting of the Swiss Society of Surgery, Switzerland, 2010. Opinions of the SSC were assessed with a 6-item questionnaire. RESULTS: 152 respondents answered the questionnaire (participation rate 35.1%. 64.7% respondents acknowledged having a checklist in their hospital or their clinic. Median implementation year was 2009. More than 8 out of 10 respondents reported their team applied the Sign In and the Time Out very often or quasi systematically, whereas almost half of respondents acknowledged the Sign Out was applied never or rarely. The majority of respondents agreed that the checklist improves safety and team communication, and helps to develop a safety culture. However, they were less supportive about the opinion that the checklist facilitates teamwork and eliminates social hierarchy between caregivers. CONCLUSIONS: This survey indicates that the SSC has been largely implemented in many Swiss hospitals and clinics. Both surgeons and anaesthetists perceived the SSC as a valuable tool in improving intraoperative patient safety and communication among health care professionals, with lesser importance in facilitating teamwork (and eliminating hierarchical categories.

Development of custom LCD based portable survey/contamination monitors

International Nuclear Information System (INIS)

Reddy, J.D.

2010-01-01

Equipments for carrying out radiation survey measurements for alpha, beta and gamma radiations have evolved considerably with the advancements in Electronics overtime. There are 2 major classes of portable instruments available from most manufacturers - (a) Analog indicator type (b) Direct digital readout type. Analog meters give a direct quantifying feel to radiation levels though they are not rich features nor they have smartness like a digital meter. Digital versions have advantages of direct readout numerically and configurable as per users requirements. To achieve best features of both the techniques a dual indicator type LCD module comprising of Analog indicating LCD segments and digital readout indicating 7 segments has been developed. This LCD comprising of LCD glass and its display driver has been deployed across various types of survey meters and contamination monitors manufactured by Nucleonix. This display now facilitates direct readout of dose rate/count rate in various units simultaneously in both analog LCD scale and direct digital indication. (author)

Photonics for safety and security

CERN Document Server

Mignani, Anna Grazia; Tajani, Antonella

2014-01-01

This volume aims to illustrate the state-of-the-art as well as the newest and latest applications of photonics in safety and security. The contributions from renowned and experienced Italian and international scientists, both from the academic and industrial community, present a multidisciplinary and comprehensive overview of this popular topic. The volume is self-contained and offers a broad survey of the various emerging technologies, as well as their applications in the real world. It spans from applications in cultural heritage, to environment, space, monitoring of coasts, quantum cryptogr

Perception of risks and safety. Results of the November 2001 survey

International Nuclear Information System (INIS)

2001-01-01

After having recalled the themes present in the survey on the perception of risks and safety as far as nuclear energy is concerned, this report proposes an analysis of the obtained results. It discusses the current general concerns, the perception of risks (confidence, truth), the perception of technological and natural risks for the environment (hazardous installations, demand for environmental acceptability of installations, disasters), the opinions on nuclear activities (image, actors, control of these activities, possibility of a nuclear accident), and finally the risks associated with radon

Integrated Status and Effectiveness Monitoring Program - Entiat River Rotary Screw Traps,Snorkel Surveys, and Steelhead Redd Surveys, 2008.

Energy Technology Data Exchange (ETDEWEB)

Nelle, R.D.; Desgroseiller, Tom; Cotter, Michael (U.S. Fish and Wildlife Service)

2009-02-17

The USFWS Mid-Columbia River Fishery Resource Office (MCRFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program from March through November of 2008. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 16,782 wild salmonids were PIT tagged during the study period. Of this, 3,961(23.6%) were wild Oncorhynchus mykiss, 6,987 (41.6%) were wild spring run O. tshawytscha, and 5,591 (33.3%) were identified as wild O. tshawytscha of unknown run. Rotary screw trap efficiencies averaged 40.3% at the upper (Rkm 11.0) trap and 7.8% for the lower (Rkm 2.0) trap. These efficiencies were pooled for emigrant O. tshawytscha and O. mykiss. The MCRFRO conducted effectiveness monitoring snorkel surveys at 24 sites during the winter period and 30 sites during the summer and fall periods of 2008 as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. The 2008 steelhead spawning grounds surveys were conducted weekly in the main Entiat River from rkm 1.1 to 44.2. A total of 222 steelhead redds were identified over the period from February 28 to June 16 2008 with April being the peak spawning month. Approximately 80% of the steelhead redds were located downstream of the rkm 26.

Ward based community road safety performance benchmarking, monitoring and intervention programmes in the City of Johannesburg

CSIR Research Space (South Africa)

Ribbens, H

2008-07-01

Full Text Available benchmarking, monitoring and intervention programme. Community road safety needs in the respective wards are articulated through the ward councillor. The rationale is that the community exactly knows where these problem areas are, because they suffer as a...

Introducing standardized “readbacks” to improve patient safety in surgery: a prospective survey in 92 providers at a public safety-net hospital

Directory of Open Access Journals (Sweden)

Prabhakar Hari

2012-06-01

Full Text Available Abstract Background Communication breakdowns represent the main root cause of preventable complications which lead to harm to surgical patients. Standardized readbacks have been successfully implemented as a main pillar of professional aviation safety for decades, to ensure a safe closed-loop communication between air traffic control and individual pilots. The present study was designed to determine the perception of staff in perioperative services regarding the role of standardized readbacks for improving patient safety in surgery at a single public safety-net hospital and level 1 trauma center. Methods A 12-item questionnaire was sent to 180 providers in perioperative services at Denver Health Medical Center. The survey was designed to determine the individual participants’ perception of (1 appropriateness of current readback processes; (2 willingness to attend a future training module on this topic; (3 specific scenarios in which readbacks may be effective; and (4 perceived major barriers to the implementation of standardized readbacks. Survey results were compared between departments (surgery versus anesthesia and between specific staff roles (attending or midlevel provider, resident physician, nursing staff, using non-parametric tests. Results The response rate to the survey was 50.1 % (n = 92. Respondents overwhelmingly recognized the role of readbacks in reducing communication errors and improving patient safety. There was a strong agreement among respondents to support participation in a readbacks training program. There was no difference in the responses between the surgery and anesthesia departments. There was a statistically significant difference in the healthcare providers willingness to attend a short training module on readbacks (p  The main challenge for respondents, which emanated from their responses, appeared to relate to determining the ideal scenarios in which readbacks may be most appropriately used. Overall

Nurse perceptions of safety climate in Australian acute hospitals: a cross-sectional survey.

Science.gov (United States)

Soh, Sze-Ee; Morello, Renata; Rifat, Sheral; Brand, Caroline; Barker, Anna

2017-03-16

Objectives The aim of the present study was to explore nurse perceptions of safety climate in acute Australian hospitals. Methods Participants included 420 nurses who have worked on 24 acute wards from six Australian hospitals. The Safety Attitudes Questionnaire (SAQ) Short Form was used to quantify nurse perceptions of safety climate and benchmarked against international data. Generalised linear mixed models were used to explore factors that may influence safety climate. Results On average, 53.5% of nurses held positive attitudes towards job satisfaction followed by teamwork climate (50.5%). There was variability in SAQ domain scores across hospitals. The safety climate and perceptions of hospital management domains also varied across wards within a hospital. Nurses who had worked longer at a hospital were more likely to have poorer perceptions of hospital management (β=-5.2; P=0.014). Overall, nurse perceptions of safety climate appeared higher than international data. Conclusions The perceptions of nurses working in acute Victorian and New South Wales hospitals varied between hospitals as well as across wards within each hospital. This highlights the importance of surveying all hospital wards and examining the results at the ward level when implementing strategies to improve patient safety and the culture of safety in organisations. What is known about the topic? Prior studies in American nursing samples have shown that hospitals with higher levels of safety climate have a lower relative incidence of preventable patient complications and adverse events. Developing a culture of safety in hospitals may be useful in targeting efforts to improve patient safety. What does this paper add? This paper has shown that the perceptions of safety climate among nurses working in acute Australian hospitals varied between hospitals and across wards within a hospital. Only half the nurses also reported positive attitudes towards job satisfaction and teamwork climate. What are

Drug Safety

Science.gov (United States)

... over-the-counter drug. The FDA evaluates the safety of a drug by looking at Side effects ... clinical trials The FDA also monitors a drug's safety after approval. For you, drug safety means buying ...

Statistical Analysis of the Worker Engagement Survey Administered at the Worker Safety and Security Team Festival

Energy Technology Data Exchange (ETDEWEB)

Davis, Adam Christopher [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-08-25

The Worker Safety and Security Team (WSST) at Los Alamos National Laboratory holds an annual festival, WSST-fest, to engage workers and inform them about safety- and securityrelated matters. As part of the 2015 WSST-fest, workers were given the opportunity to participate in a survey assessing their engagement in their organizations and work environments. A total of 789 workers participated in the 23-question survey where they were also invited, optionally, to identify themselves, their organization, and to give open-ended feedback. The survey consisted of 23 positive statements (i.e. “My organization is a good place to work.”) with which the respondent could express a level of agreement. The text of these statements are provided in Table 1. The level of agreement corresponds to a 5-level Likert scale ranging from “Strongly Disagree” to “Strongly Agree.” In addition to assessing the overall positivity or negativity of the scores, the results were partitioned into several cohorts based on the response meta-data (self-identification, comments, etc.) to explore trends. Survey respondents were presented with the options to identify themselves, their organizations and to provide comments. These options suggested the following questions about the data set.

Office Visits to Monitor Stimulant Medication Safety and Efficacy: Recommended Care.

Science.gov (United States)

Zima, Bonnie T; Norquist, Grayson S; Altchuler, Steven I; Behrens, Jacob; Iles-Shih, Matthew D; Ng, Yiu Kee Warren; Schaepper, Mary Ann

2018-06-01

The clinical guidance based on the research article, "Specific Components of Pediatricians' Medication-Related Care Predict Attention-Deficit/Hyperactivity Disorder Improvement," published in the June 2017 issue, 1 might be premature. The authors, Epstein et al., suggest that "Physicians do not need to necessarily rely on office visits to monitor medication response and side effects in the week(s) after initially prescribing medication, but instead could use phone calls or email correspondence to check in with the family" (p. 489). However, this advice has the potential to be misinterpreted that phone or email contact is acceptable clinical practice to monitor stimulant medication safety and efficacy, especially during the maintenance phase. It also could be erroneously interpreted that phone or email contact is sufficient for follow-up care for children receiving medication treatment for attention-deficit/hyperactivity disorder (ADHD) for national quality measures. Copyright © 2018 American Academy of Child and Adolescent Psychiatry. Published by Elsevier Inc. All rights reserved.

Advanced hemodynamic monitoring in intensive care medicine : A German web-based survey study.

Science.gov (United States)

Saugel, B; Reese, P C; Wagner, J Y; Buerke, M; Huber, W; Kluge, S; Prondzinsky, R

2018-04-01

Advanced hemodynamic monitoring is recommended in patients with complex circulatory shock. To evaluate the current attitudes and beliefs among German intensivists, regarding advanced hemodynamic monitoring, the actual hemodynamic management in clinical practice, and the barriers to using it. Web-based survey among members of the German Society of Medical Intensive Care and Emergency Medicine. Of 284 respondents, 249 (87%) agreed that further hemodynamic assessment is needed to determine the type of circulatory shock if no clear clinical diagnosis can be made. In all, 281 (99%) agreed that echocardiography is helpful for this purpose (transpulmonary thermodilution: 225 [79%]; pulmonary artery catheterization: 126 [45%]). More than 70% of respondents agreed that blood flow variables (cardiac output, stroke volume) should be measured in patients with hemodynamic instability. The parameters most respondents agreed should be assessed in a patient with hemodynamic instability were mean arterial pressure, cardiac output, and serum lactate. Echocardiography is available in 99% of ICUs (transpulmonary thermodilution: 91%; pulmonary artery catheter: 63%). The respondents stated that, in clinical practice, invasive arterial pressure measurements and serum lactate measurements are performed in more than 90% of patients with hemodynamic instability (cardiac output monitoring in about 50%; transpulmonary thermodilution in about 40%). The respondents did not feel strong barriers to the use of advanced hemodynamic monitoring in clinical practice. This survey study shows that German intensivists deem advanced hemodynamic assessment necessary for the differential diagnosis of circulatory shock and to guide therapy with fluids, vasopressors, and inotropes in ICU patients.

Indicators of safety culture - selection and utilization of leading safety performance indicators

Energy Technology Data Exchange (ETDEWEB)

Reiman, Teemu; Pietikaeinen, Elina (VTT, Technical Research Centre of Finland (Finland))

2010-03-15

Safety indicators play a role in providing information on organizational performance, motivating people to work on safety and increasing organizational potential for safety. The aim of this report is to provide an overview on leading safety indicators in the domain of nuclear safety. The report explains the distinction between lead and lag indicators and proposes a framework of three types of safety performance indicators - feedback, monitor and drive indicators. Finally the report provides guidance for nuclear energy organizations for selecting and interpreting safety indicators. It proposes the use of safety culture as a leading safety performance indicator and offers an example list of potential indicators in all three categories. The report concludes that monitor and drive indicators are so called lead indicators. Drive indicators are chosen priority areas of organizational safety activity. They are based on the underlying safety model and potential safety activities and safety policy derived from it. Drive indicators influence control measures that manage the socio technical system; change, maintain, reinforce, or reduce something. Monitor indicators provide a view on the dynamics of the system in question; the activities taking place, abilities, skills and motivation of the personnel, routines and practices - the organizational potential for safety. They also monitor the efficacy of the control measures that are used to manage the socio technical system. Typically the safety performance indicators that are used are lagging (feedback) indicators that measure the outcomes of the socio technical system. Besides feedback indicators, organizations should also acknowledge the important role of monitor and drive indicators in managing safety. The selection and use of safety performance indicators is always based on an understanding (a model) of the socio technical system and safety. The safety model defines what risks are perceived. It is important that the safety

Indicators of safety culture - selection and utilization of leading safety performance indicators

International Nuclear Information System (INIS)

Reiman, Teemu; Pietikaeinen, Elina

2010-03-01

Safety indicators play a role in providing information on organizational performance, motivating people to work on safety and increasing organizational potential for safety. The aim of this report is to provide an overview on leading safety indicators in the domain of nuclear safety. The report explains the distinction between lead and lag indicators and proposes a framework of three types of safety performance indicators - feedback, monitor and drive indicators. Finally the report provides guidance for nuclear energy organizations for selecting and interpreting safety indicators. It proposes the use of safety culture as a leading safety performance indicator and offers an example list of potential indicators in all three categories. The report concludes that monitor and drive indicators are so called lead indicators. Drive indicators are chosen priority areas of organizational safety activity. They are based on the underlying safety model and potential safety activities and safety policy derived from it. Drive indicators influence control measures that manage the socio technical system; change, maintain, reinforce, or reduce something. Monitor indicators provide a view on the dynamics of the system in question; the activities taking place, abilities, skills and motivation of the personnel, routines and practices - the organizational potential for safety. They also monitor the efficacy of the control measures that are used to manage the socio technical system. Typically the safety performance indicators that are used are lagging (feedback) indicators that measure the outcomes of the socio technical system. Besides feedback indicators, organizations should also acknowledge the important role of monitor and drive indicators in managing safety. The selection and use of safety performance indicators is always based on an understanding (a model) of the socio technical system and safety. The safety model defines what risks are perceived. It is important that the safety

The challenges in monitoring and preventing patient safety incidents for people with intellectual disabilities in NHS acute hospitals: evidence from a mixed-methods study.

Science.gov (United States)

Tuffrey-Wijne, Irene; Goulding, Lucy; Gordon, Vanessa; Abraham, Elisabeth; Giatras, Nikoletta; Edwards, Christine; Gillard, Steve; Hollins, Sheila

2014-09-24

There has been evidence in recent years that people with intellectual disabilities in acute hospitals are at risk of preventable deterioration due to failures of the healthcare services to implement the reasonable adjustments they need. The aim of this paper is to explore the challenges in monitoring and preventing patient safety incidents involving people with intellectual disabilities, to describe patient safety issues faced by patients with intellectual disabilities in NHS acute hospitals, and investigate underlying contributory factors. This was a 21-month mixed-method study involving interviews, questionnaires, observation and monitoring of incident reports to assess the implementation of recommendations designed to improve care provided for patients with intellectual disabilities and explore the factors that compromise or promote patient safety. Six acute NHS Trusts in England took part. Data collection included: questionnaires to clinical hospital staff (n = 990); questionnaires to carers (n = 88); interviews with: hospital staff including senior managers, nurses and doctors (n = 68) and carers (n = 37); observation of in-patients with intellectual disabilities (n = 8); monitoring of incident reports (n = 272) and complaints involving people with intellectual disabilities. Staff did not always readily identify patient safety issues or report them. Incident reports focused mostly around events causing immediate or potential physical harm, such as falls. Hospitals lacked effective systems for identifying patients with intellectual disabilities within their service, making monitoring safety incidents for this group difficult.The safety issues described by the participants were mostly related to delays and omissions of care, in particular: inadequate provision of basic nursing care, misdiagnosis, delayed investigations and treatment, and non-treatment decisions and Do Not Attempt Cardiopulmonary Resuscitation (DNACPR) orders. The events leading to avoidable harm

Radiation Safety in Industrial Radiography. Specific Safety Guide

International Nuclear Information System (INIS)

2011-01-01

This Safety Guide provides recommendations for ensuring radiation safety in industrial radiography used in non-destructive testing. This includes industrial radiography work that utilizes X ray and gamma sources, both in shielded facilities that have effective engineering controls and in outside shielded facilities using mobile sources. Contents: 1. Introduction; 2. Duties and responsibilities; 3. Safety assessment; 4. Radiation protection programme; 5. Training and qualification; 6. Individual monitoring of workers; 7. Workplace monitoring; 8. Control of radioactive sources; 9. Safety of industrial radiography sources and exposure devices; 10. Radiography in shielded enclosures; 11. Site radiography; 12. Transport of radioactive sources; 13. Emergency preparedness and response; Appendix: IAEA categorization of radioactive sources; Annex I: Example safety assessment; Annex II: Overview of industrial radiography sources and equipment; Annex III: Examples of accidents in industrial radiography.

ASIC-based design of NMR system health monitor for mission/safety-critical applications.

Science.gov (United States)

Balasubramanian, P

2016-01-01

N-modular redundancy (NMR) is a generic fault tolerance scheme that is widely used in safety-critical circuit/system designs to guarantee the correct operation with enhanced reliability. In passive NMR, at least a majority (N + 1)/2 out of N function modules is expected to operate correctly at any time, where N is odd. Apart from a conventional realization of the NMR system, it would be useful to provide a concurrent indication of the system's health so that an appropriate remedial action may be initiated depending upon an application's safety criticality. In this context, this article presents the novel design of a generic NMR system health monitor which features: (i) early fault warning logic, that is activated upon the production of a conflicting result by even one output of any arbitrary function module, and (ii) error signalling logic, which signals an error when the number of faulty function modules unfortunately attains a majority and the system outputs may no more be reliable. Two sample implementations of NMR systems viz. triple modular redundancy and quintuple modular redundancy with the proposed system health monitoring are presented in this work, with a 4-bit ALU used for the function modules. The simulations are performed using a 32/28 nm CMOS process technology.

Initial Demonstration of the Real-Time Safety Monitoring Framework for the National Airspace System Using Flight Data

Science.gov (United States)

Roychoudhury, Indranil; Daigle, Matthew; Goebel, Kai; Spirkovska, Lilly; Sankararaman, Shankar; Ossenfort, John; Kulkarni, Chetan; McDermott, William; Poll, Scott

2016-01-01

As new operational paradigms and additional aircraft are being introduced into the National Airspace System (NAS), maintaining safety in such a rapidly growing environment becomes more challenging. It is therefore desirable to have an automated framework to provide an overview of the current safety of the airspace at different levels of granularity, as well an understanding of how the state of the safety will evolve into the future given the anticipated flight plans, weather forecast, predicted health of assets in the airspace, and so on. Towards this end, as part of our earlier work, we formulated the Real-Time Safety Monitoring (RTSM) framework for monitoring and predicting the state of safety and to predict unsafe events. In our previous work, the RTSM framework was demonstrated in simulation on three different constructed scenarios. In this paper, we further develop the framework and demonstrate it on real flight data from multiple data sources. Specifically, the flight data is obtained through the Shadow Mode Assessment using Realistic Technologies for the National Airspace System (SMART-NAS) Testbed that serves as a central point of collection, integration, and access of information from these different data sources. By testing and evaluating using real-world scenarios, we may accelerate the acceptance of the RTSM framework towards deployment. In this paper we demonstrate the framework's capability to not only estimate the state of safety in the NAS, but predict the time and location of unsafe events such as a loss of separation between two aircraft, or an aircraft encountering convective weather. The experimental results highlight the capability of the approach, and the kind of information that can be provided to operators to improve their situational awareness in the context of safety.

Diagnosis function of safety status in the safety parameter display system (SPDS)

International Nuclear Information System (INIS)

Zhang Yuanfang

1993-04-01

An automatic diagnosis function of safety status for nuclear power plant adopted in the SPDS is introduced. To guarantee diagnosis diversification, two diagnosis criteria of a design basis accident monitoring and a critical safety function monitoring used in plant emergency operation are provided. As an extensive function, a parameter deviation monitoring used in plant normal operation is also provided

Evaluation of patient safety culture among Malaysian retail pharmacists: results of a self-reported survey

Science.gov (United States)

Sivanandy, Palanisamy; Maharajan, Mari Kannan; Rajiah, Kingston; Wei, Tan Tyng; Loon, Tan Wee; Yee, Lim Chong

2016-01-01

Background Patient safety is a major public health issue, and the knowledge, skills, and experience of health professionals are very much essential for improving patient safety. Patient safety and medication error are very much associated. Pharmacists play a significant role in patient safety. The function of pharmacists in the medication use process is very different from medical and nursing colleagues. Medication dispensing accuracy is a vital element to ensure the safety and quality of medication use. Objective To evaluate the attitude and perception of the pharmacist toward patient safety in retail pharmacies setup in Malaysia. Methods A Pharmacy Survey on Patient Safety Culture questionnaire was used to assess patient safety culture, developed by the Agency for Healthcare Research and Quality, and the convenience sampling method was adopted. Results The overall positive response rate ranged from 31.20% to 87.43%, and the average positive response rate was found to be 67%. Among all the eleven domains pertaining to patient safety culture, the scores of “staff training and skills” were less. Communication openness, and patient counseling are common, but not practiced regularly in the Malaysian retail pharmacy setup compared with those in USA. The overall perception of patient safety of an acceptable level in the current retail pharmacy setup. Conclusion The study revealed that staff training, skills, communication in patient counseling, and communication across shifts and about mistakes are less in current retail pharmacy setup. The overall perception of patient safety should be improved by educating the pharmacists about the significance and essential of patient safety. PMID:27524887

Evaluation of patient safety culture among Malaysian retail pharmacists: results of a self-reported survey.

Science.gov (United States)

Sivanandy, Palanisamy; Maharajan, Mari Kannan; Rajiah, Kingston; Wei, Tan Tyng; Loon, Tan Wee; Yee, Lim Chong

2016-01-01

Patient safety is a major public health issue, and the knowledge, skills, and experience of health professionals are very much essential for improving patient safety. Patient safety and medication error are very much associated. Pharmacists play a significant role in patient safety. The function of pharmacists in the medication use process is very different from medical and nursing colleagues. Medication dispensing accuracy is a vital element to ensure the safety and quality of medication use. To evaluate the attitude and perception of the pharmacist toward patient safety in retail pharmacies setup in Malaysia. A Pharmacy Survey on Patient Safety Culture questionnaire was used to assess patient safety culture, developed by the Agency for Healthcare Research and Quality, and the convenience sampling method was adopted. The overall positive response rate ranged from 31.20% to 87.43%, and the average positive response rate was found to be 67%. Among all the eleven domains pertaining to patient safety culture, the scores of "staff training and skills" were less. Communication openness, and patient counseling are common, but not practiced regularly in the Malaysian retail pharmacy setup compared with those in USA. The overall perception of patient safety of an acceptable level in the current retail pharmacy setup. The study revealed that staff training, skills, communication in patient counseling, and communication across shifts and about mistakes are less in current retail pharmacy setup. The overall perception of patient safety should be improved by educating the pharmacists about the significance and essential of patient safety.

A Survey on Data Quality for Dependable Monitoring in Wireless Sensor Networks.

Science.gov (United States)

Jesus, Gonçalo; Casimiro, António; Oliveira, Anabela

2017-09-02

Wireless sensor networks are being increasingly used in several application areas, particularly to collect data and monitor physical processes. Non-functional requirements, like reliability, security or availability, are often important and must be accounted for in the application development. For that purpose, there is a large body of knowledge on dependability techniques for distributed systems, which provide a good basis to understand how to satisfy these non-functional requirements of WSN-based monitoring applications. Given the data-centric nature of monitoring applications, it is of particular importance to ensure that data are reliable or, more generically, that they have the necessary quality. In this survey, we look into the problem of ensuring the desired quality of data for dependable monitoring using WSNs. We take a dependability-oriented perspective, reviewing the possible impairments to dependability and the prominent existing solutions to solve or mitigate these impairments. Despite the variety of components that may form a WSN-based monitoring system, we give particular attention to understanding which faults can affect sensors, how they can affect the quality of the information and how this quality can be improved and quantified.

Safety Evakuation Of Triga-2000 Reactor Operation Viewed From Safety Culture

International Nuclear Information System (INIS)

Karliana, Itjeu

2001-01-01

The safety evaluation activities of TRIGA-2000 operation viewed from safety culture performed by questioners data collected from the operators and supervisor site of TRIGA-2000 P3TN, Bandung. There are 9 activity aspects surveyed, for instant to avail the policy of safety from their chairman, safety management, education and training, emergency aids planning, safety consultancy, accident information, safety analysis, safety devices, safety and occupational health. The surveying undertaken by filling the questioner that containing of 9 activity aspects and 20 samples of employees. The safety evaluation results' of the operation personnel in TRIGA-2000 P3TN are good implemented by both the operators and supervisors should be improve and attention need to provide the equipment's. The education and training especially for safety refreshment must be performing

An Online Risk Monitor System (ORMS) to Increase Safety and Security Levels in Industry

International Nuclear Information System (INIS)

Zubair, M; Ur Rahman, Khalil; Ul Hassan, Mehmood

2013-01-01

The main idea of this research is to develop an Online Risk Monitor System (ORMS) based on Living Probabilistic Safety Assessment (LPSA). The article highlights the essential features and functions of ORMS. The basic models and modules such as, Reliability Data Update Model (RDUM), running time update, redundant system unavailability update, Engineered Safety Features (ESF) unavailability update and general system update have been described in this study. ORMS not only provides quantitative analysis but also highlights qualitative aspects of risk measures. ORMS is capable of automatically updating the online risk models and reliability parameters of equipment. ORMS can support in the decision making process of operators and managers in Nuclear Power Plants

An Online Risk Monitor System (ORMS) to Increase Safety and Security Levels in Industry

Science.gov (United States)

Zubair, M.; Rahman, Khalil Ur; Hassan, Mehmood Ul

2013-12-01

The main idea of this research is to develop an Online Risk Monitor System (ORMS) based on Living Probabilistic Safety Assessment (LPSA). The article highlights the essential features and functions of ORMS. The basic models and modules such as, Reliability Data Update Model (RDUM), running time update, redundant system unavailability update, Engineered Safety Features (ESF) unavailability update and general system update have been described in this study. ORMS not only provides quantitative analysis but also highlights qualitative aspects of risk measures. ORMS is capable of automatically updating the online risk models and reliability parameters of equipment. ORMS can support in the decision making process of operators and managers in Nuclear Power Plants.

Results of a survey on accident and safety analysis codes, benchmarks, verification and validation methods

International Nuclear Information System (INIS)

Lee, A.G.; Wilkin, G.B.

1996-03-01

During the 'Workshop on R and D needs' at the 3rd Meeting of the International Group on Research Reactors (IGORR-III), the participants agreed that it would be useful to compile a survey of the computer codes and nuclear data libraries used in accident and safety analyses for research reactors and the methods various organizations use to verify and validate their codes and libraries. Five organizations, Atomic Energy of Canada Limited (AECL, Canada), China Institute of Atomic Energy (CIAE, People's Republic of China), Japan Atomic Energy Research Institute (JAERI, Japan), Oak Ridge National Laboratories (ORNL, USA), and Siemens (Germany) responded to the survey. The results of the survey are compiled in this report. (author) 36 refs., 3 tabs

Safety Gear Decontamination Practices Among Florida Firefighters: Analysis of a Text-Based Survey Methodology.

Science.gov (United States)

Moore, Kevin J; Koru-Sengul, Tulay; Alvarez, Armando; Schaefer-Solle, Natasha; Harrison, Tyler R; Kobetz, Erin N; Caban-Martinez, Alberto J

2018-02-01

Despite the National Fire Protection Association (NFPA) 1851 Personal Protective Equipment Care and Maintenance guidelines, little is known about the routine cleaning of firefighter bunker gear. In collaboration with a large Florida firefighter union, a mobile phone text survey was administered, which included eight questions in an item logic format. In total, 250 firefighters participated in the survey of which 65% reported cleaning their bunker gear in the past 12 months. Approximately 32% ( n = 52) indicated that they had above average confidence in gear cleaning procedures. Arriving at a fire incident response was a significant predictor of gear cleaning in the 12 months preceding survey administration. Using mobile phone-based texting for periodic queries on adherence to NFPA cleaning guidelines and safety message distribution may assist firefighters to increase decontamination procedure frequency.

Survey of Employees' Safety Attitude in a Teaching Hospital Tehran 2010

Directory of Open Access Journals (Sweden)

M. Mahmmoudi

2011-01-01

Full Text Available Background and aimsThe Medical Errors and the potential unsafe actions are always regarded as a serious trouble by the managers and health care providers. Using the employees' attitude data as a measurement criterion in the evaluation of the hospitals performance in the field of the “Safety” can improve the safety level among the personnel and patients . Survey of employees' attitude about safety and its comparison with different groups of offering health services in a teaching Hospital was the main objective of present study.   MethodsIn order to specify patient safety culture in Moddares hospital, all employees including physicians, nurses, managers and employees of Para-clinic, a volume sample consisting of 212 persons were selected. Then it was used from questionnaire of safety attitude within 6 dimensions including Teamwork climate, Safety climate, perceptions of Management , Job Satisfaction, Working Conditions and Stress Recognition. At first this questionnaire was gone under assessing validity and trust. The scale of measuring, Likert was 5 grades. In order to specify difference between groups under study it was used from ANOVA test.   Results Positive safety culture within 6 dimensions including Teamwork Climate, Safety climate, Job Satisfaction, Stress Recognition, Perception of Management , Working Conditions for doctors were 3, 4.13, 17.4, 0, 4.3, and 8.7 respectively; the aforesaid Dimensions for nurses were 19, 2.6, 10.3, 7.8, 2.6 and 15.5 respectively, the aforesaid Dimensions for managers were 30.3, 6.1, 33.3, 0, 18.2 and 21.2 respectively and the aforesaid Dimensions for employees of Para-clinic Were 50, 12.5, 25, 12.5, 10 and 37.5 respectively. There was Significant difference from View Point of statistics (p<0.5 from Dimensions of Job satisfaction among managers and nurses, employees of Para-clinic and nurses this difference Were zero and 0.001. From View Point of Stress recognition among managers and employees of Para

Patient safety in surgical environments: Cross-countries comparison of psychometric properties and results of the Norwegian version of the Hospital Survey on Patient Safety

Directory of Open Access Journals (Sweden)

Nortvedt Monica W

2010-09-01

Full Text Available Abstract Background How hospital health care personnel perceive safety climate has been assessed in several countries by using the Hospital Survey on Patient Safety (HSOPS. Few studies have examined safety climate factors in surgical departments per se. This study examined the psychometric properties of a Norwegian translation of the HSOPS and also compared safety climate factors from a surgical setting to hospitals in the United States, the Netherlands and Norway. Methods This survey included 575 surgical personnel in Haukeland University Hospital in Bergen, an 1100-bed tertiary hospital in western Norway: surgeons, operating theatre nurses, anaesthesiologists, nurse anaesthetists and ancillary personnel. Of these, 358 returned the HSOPS, resulting in a 62% response rate. We used factor analysis to examine the applicability of the HSOPS factor structure in operating theatre settings. We also performed psychometric analysis for internal consistency and construct validity. In addition, we compared the percent of average positive responds of the patient safety climate factors with results of the US HSOPS 2010 comparative data base report. Results The professions differed in their perception of patient safety climate, with anaesthesia personnel having the highest mean scores. Factor analysis using the original 12-factor model of the HSOPS resulted in low reliability scores (r = 0.6 for two factors: "adequate staffing" and "organizational learning and continuous improvement". For the remaining factors, reliability was ≥ 0.7. Reliability scores improved to r = 0.8 by combining the factors "organizational learning and continuous improvement" and "feedback and communication about error" into one six-item factor, supporting an 11-factor model. The inter-item correlations were found satisfactory. Conclusions The psychometric properties of the questionnaire need further investigations to be regarded as reliable in surgical environments. The operating

Voices of nuclear power 'monitors' in fiscal 1985: results of the questionnaire

International Nuclear Information System (INIS)

1986-01-01

The system of nuclear power 'monitors' is to hear opinions etc. of the general people (i.e. of nuclear power monitors) on the nuclear power development and utilization and thereby to reflect the results in the nuclear power administration in Japan. The questionnairing survey by mail was made in June 1985 with 536 monitors across the country, of which 474 answered the questions. The results are described in the following: energies in the future, the development of nuclear power, the development of advanced-type reactors, the nuclear fuel cycle, nuclear power safety administration, nuclear hazard prevention, nuclear power PR activities. (Mori, K.)

Real-time environmental monitoring at the Japan Nuclear Cycle Development Institute O-arai Engineering Center. Using the internet to promote safety and environmental transparency

International Nuclear Information System (INIS)

Motomatsu, Sheila; Nakashima Inoue, Naoko

2000-12-01

The report documents the results of an effort at the Japan Nuclear Cycle Development Institute O-arai Engineering Center (JNC/OEC) to provide via the Internet, in real-time, environmental monitoring data to promote safety and environmental transparency. Provided in Japanese as well as in English, the Internet site provides assurance that OEC nuclear operations are being conducted in a manner that is safe to both people in the surrounding area and the environment. This work conducted by Environmental Monitoring Team of the OEC Safety Administration Section fulfilled the assignment to release data real-time via the Internet tasked by the Information Disclosure Section of the JNC Headquarters Public Relations Division. The work conducted by the visiting exchange scientist fulfilled the experimental portion of Action Sheet 34 of the Agreement between JNC and DOE for Cooperation in Research and Development Concerning Nuclear Material Control and Accounting Measures for Safeguards and Nonproliferation. In Japan, the project for Action Sheet 34 Personnel Exchange on Remote Monitoring and Transparency' entailed both a study and an experiment on how remote monitoring technologies can be used to promote nonproliferation, environmental and safety transparency. Environmental airborne radionuclide monitoring falls under the definition of remote monitoring technology more broadly defined as 'remotely accessed unattended monitoring system technology'. (author)

Development of a web based monitoring system for safety and activity analysis in operating theatres.

Science.gov (United States)

Frosini, Francesco; Miniati, Roberto; Avezzano, Paolo; Cecconi, Giulio; Dori, Fabrizio; Gentili, Guido Biffi; Belardinelli, Andrea

2016-01-01

The management and the monitoring of the operating rooms on the part of the general management have the objective of optimizing their use and maximizing the internal safety. The expenses owed to their safe use represent, besides reimbursements coming from the surgical activity, important factors for the analysis of the medical facility. Given that it is not possible to reduce the safety, it is necessary to develop supporting systems with the aim to enhance and optimize the use of the rooms. The developed analysis model of the operating rooms in this study is based on the specific performance indicators and allows the effective monitoring of both the parameters that influence the safety (environmental, microbiological parameters) and those that influence the efficiency of the usage (employment rate, delays, necessary formalities, etc.). This allows you to have a systematic dashboard on hand for all of the OTs and, thus, organize the intervention schedules and more appropriate improvements. A monitoring dashboard has been achieved, accessible from any platform and any device, capable of aggregating hospital information. The undertaken organizational modifications, through the use of the dashboard, have allowed for an average annual savings of 29.52 minutes per intervention and increase the use of the ORs of 5%. The increment of the employment rate and the optimization of the operating room have allowed for savings of around $299,88 for every intervention carried out in 2013, corresponding to an annual savings of $343,362,60. Integration dashboards, as the one proposed in this study as a prototype, represent a governance model of economically sustainable healthcare systems capable of guiding the hospital management in the choices and in the implementation of the most efficient organizational modifications.

U.S. Geological Survey continuous monitoring workshop—Workshop summary report

Science.gov (United States)

Sullivan, Daniel J.; Joiner, John K.; Caslow, Kerry A.; Landers, Mark N.; Pellerin, Brian A.; Rasmussen, Patrick P.; Sheets, Rodney A.

2018-04-20

Executive SummaryThe collection of high-frequency (in other words, “continuous”) water data has been made easier over the years because of advances in technologies to measure, transmit, store, and query large, temporally dense datasets. Commercially available, in-situ sensors and data-collection platforms—together with new techniques for data analysis—provide an opportunity to monitor water quantity and quality at time scales during which meaningful changes occur. The U.S. Geological Survey (USGS) Continuous Monitoring Workshop was held to build stronger collaboration within the Water Mission Area on the collection, interpretation, and application of continuous monitoring data; share technical approaches for the collection and management of continuous data that improves consistency and efficiency across the USGS; and explore techniques and tools for the interpretation of continuous monitoring data, which increases the value to cooperators and the public. The workshop was organized into three major themes: Collecting Continuous Data, Understanding and Using Continuous Data, and Observing and Delivering Continuous Data in the Future. Presentations each day covered a variety of related topics, with a special session at the end of each day designed to bring discussion and problem solving to the forefront.The workshop brought together more than 70 USGS scientists and managers from across the Water Mission Area and Water Science Centers. Tools to manage, assure, control quality, and explore large streams of continuous water data are being developed by the USGS and other organizations and will be critical to making full use of these high-frequency data for research and monitoring. Disseminating continuous monitoring data and findings relevant to critical cooperator and societal issues is central to advancing the USGS networks and mission. Several important outcomes emerged from the presentations and breakout sessions.

Current practices in long-term video-EEG monitoring services: A survey among partners of the E-PILEPSY pilot network of reference for refractory epilepsy and epilepsy surgery.

Science.gov (United States)

Kobulashvili, Teia; Höfler, Julia; Dobesberger, Judith; Ernst, Florian; Ryvlin, Philippe; Cross, J Helen; Braun, Kees; Dimova, Petia; Francione, Stefano; Hecimovic, Hrvoje; Helmstaedter, Christoph; Kimiskidis, Vasilios K; Lossius, Morten Ingvar; Malmgren, Kristina; Marusic, Petr; Steinhoff, Bernhard J; Boon, Paul; Craiu, Dana; Delanty, Norman; Fabo, Daniel; Gil-Nagel, Antonio; Guekht, Alla; Hirsch, Edouard; Kalviainen, Reetta; Mameniskiené, Ruta; Özkara, Çiğdem; Seeck, Margitta; Rubboli, Guido; Krsek, Pavel; Rheims, Sylvain; Trinka, Eugen

2016-05-01

The European Union-funded E-PILEPSY network aims to improve awareness of, and accessibility to, epilepsy surgery across Europe. In this study we assessed current clinical practices in epilepsy monitoring units (EMUs) in the participating centers. A 60-item web-based survey was distributed to 25 centers (27 EMUs) of the E-PILEPSY network across 22 European countries. The questionnaire was designed to evaluate the characteristics of EMUs, including organizational aspects, admission, and observation of patients, procedures performed, safety issues, cost, and reimbursement. Complete responses were received from all (100%) EMUs surveyed. Continuous observation of patients was performed in 22 (81%) EMUs during regular working hours, and in 17 EMUs (63%) outside of regular working hours. Fifteen (56%) EMUs requested a signed informed consent before admission. All EMUs performed tapering/withdrawal of antiepileptic drugs, 14 (52%) prior to admission to an EMU. Specific protocols on antiepileptic drugs (AED) tapering were available in four (15%) EMUs. Standardized Operating Procedures (SOP) for the treatment of seizure clusters and status epilepticus were available in 16 (59%). Safety measures implemented by EMUs were: alarm seizure buttons in 21 (78%), restricted patient's ambulation in 19 (70%), guard rails in 16 (59%), and specially designated bathrooms in 7 (26%). Average costs for one inpatient day in EMU ranged between 100 and 2200 Euros. This study shows a considerable diversity in the organization and practice patterns across European epilepsy monitoring units. The collected data may contribute to the development and implementation of evidence-based recommended practices in LTM services across Europe. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Integrated Status and Effectiveness Monitoring Program - Entiat River Rotary Screw Traps, Snorkel Surveys, and Steelhead Redd Surveys, 2008-2009.

Energy Technology Data Exchange (ETDEWEB)

Nelle, R.D.; Desgroseillier, Tom; Cotter, Michael [U.S. Fish and Wildlife Service

2009-04-14

The USFWS Mid-Columbia River Fishery Resource Office (MCRFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program from March through November of 2008. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 16,782 wild salmonids were PIT tagged during the study period. Of this, 3,961(23.6%) were wild Oncorhynchus mykiss, 6,987 (41.6%) were wild spring run O. tshawytscha, and 5,591 (33.3%) were identified as wild O. tshawytscha of unknown run. Rotary screw trap efficiencies averaged 40.3% at the upper (Rkm 11.0) trap and 7.8% for the lower (Rkm 2.0) trap. These efficiencies were pooled for emigrant O. tshawytscha and O. mykiss. The MCRFRO conducted effectiveness monitoring snorkel surveys at 24 sites during the winter period and 30 sites during the summer and fall periods of 2008 as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. The 2008 steelhead spawning grounds surveys were conducted weekly in the main Entiat River from rkm 1.1 to 44.2. A total of 222 steelhead redds were identified over the period from February 28 to June 16 2008 with April being the peak spawning month. Approximately 80% of the steelhead redds were located downstream of the rkm 26.

On-line generation of three-dimensional core power distribution using incore detector signals to monitor safety limits

International Nuclear Information System (INIS)

Jang, Jin Wook; Lee, Ki Bog; Na, Man Gyun; Lee, Yoon Joon

2004-01-01

It is essential in commercial reactors that the safety limits imposed on the fuel pellets and fuel clad barriers, such as the Linear Power Density (LPD) and the Departure from Nucleate Boiling Ratio (DNBR), are not violated during reactor operations. In order to accurately monitor the safety limits of current reactor states, a detailed three-dimensional (3D) core power distribution should be estimated from the in-core detector signals. In this paper, we propose a calculation methodology for detailed 3D core power distribution, using in-core detector signals and core monitoring constants such as the 3D Coupling Coefficients (3DCC), node power fraction, and pin-to-node factors. Also, the calculation method for several core safety parameters is introduced. The core monitoring constants for the real core state are promptly provided by the core design code and on-line MASTER(Multi-purpose Analyzer for Static and Transient Effects of Reactors), coupled with the core monitoring program. Through the plant computer, core state variables, which include reactor thermal power, control rod bank position, boron concentration, inlet moderator temperature, and flow rate, are supplied as input data for MASTER. MASTER performs the core calculation based on the neutron balance equation and generates several core monitoring constants corresponding to the real core state in addition to the expected core power distribution. The accuracy of the developed method is verified through a comparison with the current CECOR method. Because in all the verification calculation cases the proposed method shows a more conservative value than the best estimated value and a less conservative one than the current CECOR and COLSS methods, it is also confirmed that this method secures a greater operating margin through the simulation of the YGN-3 cycle-1 core from the viewpoint of the power peaking factor for the LPD and the pseudo hot pin axial power distribution for the DNBR calculation

Trainee Knowledge of Imaging Appropriateness and Safety: Results of a Series of Surveys From a Large Academic Medical Center.

Science.gov (United States)

Hollingsworth, Thaddeus D; Duszak, Richard; Vijayasarathi, Arvind; Gelbard, Rondi B; Mullins, Mark E

2017-10-31

In order to provide high quality care to their patients and utilize imaging most judiciously, physician trainees should possess a working knowledge of appropriate use, radiation dose, and safety. Prior work has suggested knowledge gaps in similar areas. We aimed to evaluate the knowledge of imaging appropriateness, radiation dose, and MRI and contrast safety of physician trainees across a variety of specialties. Between May 2016 and January 2017, three online surveys were distributed to all interns, residents, and fellows in ACGME accredited training programs at a large academic institution over two academic years. Response rates to three surveys ranged from 17.2% (218 of 1266) for MRI and contrast material safety, 19.1% (242 of 1266) for imaging appropriateness, to19.9% (246 of 1238) for radiation dose. Overall 72% (509 of 706) of survey respondents reported regularly ordering diagnostic imaging examinations, but fewer than half (47.8%; 470 of 984) could correctly estimate radiation dose across four commonly performed imaging studies. Only one third (34%; 167 of 488) of trainees chose appropriate imaging in scenarios involving pregnant patients. Trainee post-graduate year was not significantly correlated with overall radiation safety scores, and no significant difference was found between radiation safety or appropriate imaging scores of those who participated in a medical school radiology elective vs. those who did not. A total of 84% (57 of 68) of radiology trainees and 43% (269 of 630) of non-radiology trainees considered their knowledge adequate but that correlated only weakly correlated to actual knowledge scores (pimaging safety exist among many trainees. In order to enhance the value of imaging at the population level, further work is needed to assess the most appropriate method and stage of training to address these knowledge gaps. Copyright © 2017 Elsevier Inc. All rights reserved.

Survey and analysis of radiation safety management systems at medical institutions. Initial report. Radiation protection supervisor, radiation safety organization, and education and training

International Nuclear Information System (INIS)

Ohba, Hisateru; Ogasawara, Katsuhiko; Aburano, Tamio

2005-01-01

In this study, a questionnaire survey was carried out to determine the actual situation of radiation safety management systems in Japanese medical institutions with nuclear medicine facilities. The questionnaire consisted of questions concerning the Radiation Protection Supervisor license, safety management organizations, and problems related to education and training in safety management. Analysis was conducted according to region, type of establishment, and number of beds. The overall response rate was 60%, and no significant difference in response rate was found among regions. Medical institutions that performed nuclear medicine practices without a radiologist participating accounted for 10% of the total. Medical institutions where nurses gave patients intravenous injections of radiopharmaceuticals as part of the nuclear medicine practices accounted for 28% of the total. Of these medical institutions, 59% provided education and training in safety management for nurses. The rate of acquisition of Radiation Protection Supervisor licenses was approximately 70% for radiological technologists and approximately 20% for physicians (regional difference, p=0.02). The rate of medical institutions with safety management organizations was 71% of the total. Among the medical institutions (n=208) without safety management organizations, approximately 56% had 300 beds or fewer. In addition, it became clear that 35% of quasi-public organizations and 44% of private organizations did not provide education and training in safety management (p<0.001, according to establishment). (author)

National distracted driving telephone survey finds most drivers answer the call, hold the phone, and continue to drive : traffic tech.

Science.gov (United States)

2011-12-01

The National Highway Traffic Safety Administration conducted : the first of several periodic national surveys of distracted : driving to monitor the publics attitudes, knowledge, : and self-reported behavior about cell phones, texting, and : drive...

Safeguarding the User - Developing a Multimodal Design for Surveying and Raising Internet Safety and Security Awareness

DEFF Research Database (Denmark)

Gjedde, Lisa; Sharp, Robin; Andersen, Preben

2009-01-01

Internet safety and security for the user is an issue of great importance for the successful implementation of ICT, but since it is a complex field, with a specialist vocabulary that cannot immediately be understood by the common user, it is difficult to survey the field. The user may not underst......Internet safety and security for the user is an issue of great importance for the successful implementation of ICT, but since it is a complex field, with a specialist vocabulary that cannot immediately be understood by the common user, it is difficult to survey the field. The user may...... describes an ICT-based research method that combines a verbal mode of inquiry with a visual mode employing illustrations, animations and simulations to provide the user with a multimodal media experience. The rationale for this is that we are working in a complex technical field with a specialist vocabulary...

Implementation of the safety culture for HANARO safety management

Energy Technology Data Exchange (ETDEWEB)

Wu, Jong Sup; Han, Gee Yang; Kim, Ik Soo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2008-11-15

Safety is the fundamental principal upon which a management system is based. The IAEA INSAG(International Nuclear Safety Group) states the general aims of a safety management system. One of which is to foster and support a strong safety culture through the development and reinforcement of good safety attitudes and behavior in individuals and teams, so as to allow them to carry out their tasks safety. The safety culture activities have been implemented and the importance of a safety management in nuclear activities for a reactor application and utilization has also been emphasized for more than 10 years in HANARO which is a 30 MW multi purpose research reactor that achieved its first criticality in February 1995. The safety culture activities and implementation have been conducted continuously to enhance its safe operation such as the seminars and lectures related to safety matters, participation in international workshops and the development of safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture, the development of operational safety performance indicators (SPIs), the preparation of a safety text book and the development of an e Learning program for a safety education purpose.

Implementation of the safety culture for HANARO safety management

International Nuclear Information System (INIS)

Wu, Jong Sup; Han, Gee Yang; Kim, Ik Soo

2008-01-01

Safety is the fundamental principal upon which a management system is based. The IAEA INSAG(International Nuclear Safety Group) states the general aims of a safety management system. One of which is to foster and support a strong safety culture through the development and reinforcement of good safety attitudes and behavior in individuals and teams, so as to allow them to carry out their tasks safety. The safety culture activities have been implemented and the importance of a safety management in nuclear activities for a reactor application and utilization has also been emphasized for more than 10 years in HANARO which is a 30 MW multi purpose research reactor that achieved its first criticality in February 1995. The safety culture activities and implementation have been conducted continuously to enhance its safe operation such as the seminars and lectures related to safety matters, participation in international workshops and the development of safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture, the development of operational safety performance indicators (SPIs), the preparation of a safety text book and the development of an e Learning program for a safety education purpose

A survey of dynamic methodologies for probabilistic safety assessment of nuclear power plants

International Nuclear Information System (INIS)

Aldemir, Tunc

2013-01-01

Highlights: ► Dynamic methodologies for probabilistic safety assessment (PSA) are surveyed. ► These methodologies overcome the limitations of the traditional approach to PSA. ► They are suitable for PSA using a best estimate plus uncertainty approach. ► They are highly computation intensive and produce very large number of scenarios. ► Use of scenario clustering can assist the analysis of the results. -- Abstract: Dynamic methodologies for probabilistic safety assessment (PSA) are defined as those which use a time-dependent phenomenological model of system evolution along with its stochastic behavior to account for possible dependencies between failure events. Over the past 30 years, numerous concerns have been raised in the literature regarding the capability of the traditional static modeling approaches such as the event-tree/fault-tree methodology to adequately account for the impact of process/hardware/software/firmware/human interactions on the stochastic system behavior. A survey of the types of dynamic PSA methodologies proposed to date is presented, as well as a brief summary of an example application for the PSA modeling of a digital feedwater control system of an operating pressurized water reactor. The use of dynamic methodologies for PSA modeling of passive components and phenomenological uncertainties are also discussed.

Perception of risks and safety. Results of the October 2000 survey

International Nuclear Information System (INIS)

2000-01-01

After having recalled the themes present in the survey on the perception of risks and safety as far as nuclear energy is concerned, this report proposes an analysis of the obtained results. It discusses the current general concerns, the perception of risks (confidence, truth), the opinions on the scientific expertise, the perception of technological and natural risks for the environment (hazardous installations, demand for environmental acceptability of installations, disasters), the opinions on nuclear activities (image, actors, information, control of these activities), the possibility of a nuclear accident and the implemented countermeasures, and finally the risks associated with radon

Perception of risks and safety. Results of the October 1999 survey

International Nuclear Information System (INIS)

1999-01-01

After having recalled the themes present in the survey on the perception of risks and safety as far as nuclear energy is concerned, this report proposes an analysis of the obtained results. It discusses the current general concerns, the perception of risks (demand, confidence, truth), the opinions on scientific expertise, the opinions on nuclear activities (image, actors, information, control of these activities), the issue of radioactive wastes and mining residues (perceived risk depending on the site vicinity, time scale, site management), the possibility of a nuclear accident and the implemented countermeasures, and finally the risks concerning food

Examination of issues related to the development and implementation of real-time operational safety monitoring tools in the nuclear power industry

International Nuclear Information System (INIS)

Puglia, William J.; Atefi, Bahman

1995-01-01

In recent years, risk and reliability techniques have been increasingly used to optimize deterministic requirements and to improve the operational safety of nuclear power stations. This paper discusses the historical development and current status of implementation of real-time operational safety monitoring tools in the nuclear power industry worldwide. A safety monitor is defined as a PC-based risk management tool, based on a plant specific PSA, which can be used to manage plant safety during the day-to-day operation of a nuclear power plant by planning maintenance activities and providing advisory information to plant operational staff in order to avoid high risk plant configurations. As this technique has only been applied in a few plants worldwide, the technology is still evolving and there are several technical and implementation-related issues which still need to be resolved. This paper attempts to summarize all such issues and describe how they have been addressed in several different applications of this technology around the world

Assessing Drinking Water Quality and Water Safety Management in Sub-Saharan Africa Using Regulated Monitoring Data.

Science.gov (United States)

Kumpel, Emily; Peletz, Rachel; Bonham, Mateyo; Khush, Ranjiv

2016-10-18

Universal access to safe drinking water is prioritized in the post-2015 Sustainable Development Goals. Collecting reliable and actionable water quality information in low-resource settings, however, is challenging, and little is known about the correspondence between water quality data collected by local monitoring agencies and global frameworks for water safety. Using 42 926 microbial water quality test results from 32 surveillance agencies and water suppliers in seven sub-Saharan African countries, we determined the degree to which water sources were monitored, how water quality varied by source type, and institutional responses to results. Sixty-four percent of the water samples were collected from piped supplies, although the majority of Africans rely on nonpiped sources. Piped supplies had the lowest levels of fecal indicator bacteria (FIB) compared to any other source type: only 4% of samples of water piped to plots and 2% of samples from water piped to public taps/standpipes were positive for FIB (n = 14 948 and n = 12 278, respectively). Among other types of improved sources, samples from harvested rainwater and boreholes were less often positive for FIB (22%, n = 167 and 31%, n = 3329, respectively) than protected springs or protected dug wells (39%, n = 472 and 65%, n = 505). When data from different settings were aggregated, the FIB levels in different source types broadly reflected the source-type water safety framework used by the Joint Monitoring Programme. However, the insufficient testing of nonpiped sources relative to their use indicates important gaps in current assessments. Our results emphasize the importance of local data collection for water safety management and measurement of progress toward universal safe drinking water access.

Barriers to the Adoption of Wearable Sensors in the Workplace: A Survey of Occupational Safety and Health Professionals.

Science.gov (United States)

Schall, Mark C; Sesek, Richard F; Cavuoto, Lora A

2018-05-01

To gather information on the (a) types of wearable sensors, particularly personal activity monitors, currently used by occupational safety and health (OSH) professionals; (b) potential benefits of using such technologies in the workplace; and (c) perceived barriers preventing the widespread adoption of wearable sensors in industry. Wearable sensors are increasingly being promoted as a means to improve employee health and well-being, and there is mounting evidence supporting their use as exposure assessment and personal health tools. Despite this, many workplaces have been hesitant to adopt these technologies. An electronic survey was emailed to 28,428 registered members of the American Society of Safety Engineers (ASSE) and 1,302 professionals certified by the Board of Certification in Professional Ergonomics (BCPE). A total of 952 valid responses were returned. Over half of respondents described being in favor of using wearable sensors to track OSH-related risk factors and relevant exposure metrics at their respective workplaces. However, barriers including concerns regarding employee privacy/confidentiality of collected data, employee compliance, sensor durability, the cost/benefit ratio of using wearables, and good manufacturing practice requirements were described as challenges precluding adoption. The broad adoption of wearable technologies appears to depend largely on the scientific community's ability to successfully address the identified barriers. Investigators may use the information provided to develop research studies that better address OSH practitioner concerns and help technology developers operationalize wearable sensors to improve employee health and well-being.

The level of knowledge and radiation safety practice amongst cardiovascular technology, medical assistant, nursing and diagnostic radiography students and dose monitoring in radiography laboratory of Kolej Islam Sains dan Teknologi, Kelantan

International Nuclear Information System (INIS)

Ainul Fadhlin Othman; Amran Abdul Majid

2013-01-01

Full-text: This study investigated the knowledge level and practices regarding radiation safety among the cardiovascular technology, medical assistant nursing and radiography diagnostic students of Kolej Islam Sains dan Teknologi (KIST). The objectives of this study are to monitor the dose rate at radiography lab and to propose the guideline on radiation safety topics to improve the syllabus. 274 respondents including 30 psychology students acting as the control group were asked to answer questions from the questionnaires which cover the topics of basic knowledge of radiation and radiation safety practice. There was a significant difference (p < 0.05) between the correct answers and courses for 18 questions except for the question 4. There was a significant different (p < 0.05) between the correct answers and year of study for the questions 4, 5, 7, 12 to 15 and 18 to 20. There was a significance different (p < 0.05) between the correct answers and gender for questions 7, 11 and 19. For area dose monitoring in the radiography diagnostic lab, the assessment report on film batches of 4 walls in the lab were recorded and Victoreen451-RYR survey meter was used to monitor the dose rate for 7 selected areas with the exposure factors set for the chest, abdomen, upper extremity, lower extremity and skull radiography examinations. The dose rates at area 1 to 4, area 5 during the examination of chest, abdomen and skull, area 6 during the examination of abdomen and area 7 during the examination of abdomen, had exceeded the dose limit for radiation worker. The dose rate at the area 1 and 4 are slightly higher than the other areas. The contributing factors are the distance, tube potential, collimation and X-ray tube angulation. This study had shown that the cardiovascular technology and diagnostic radiography students have better knowledge and radiation safety practice level than the medical assistant and nursing students. In general, the level of knowledge and radiation safety

Airborne systems for emergency radiological monitoring

International Nuclear Information System (INIS)

Jupiter, C.; Boyns, P.

1976-01-01

A variety of aerial radiological monitoring systems are available to respond to a radiological accident or incident affecting large areas. These are operated by EG and G, Inc. for ERDA's Division of Operational Safety. A survey system can be airborne within approximately two hours after notification. Both airborne and terrestrial radioactivity can be measured and mapped. Special analysis procedures allow discrimination between radioactivity from most man-made radioelements and naturally occurring radioelements. A position accuracy of +-54 feet can be maintained over a large area survey. Detection sensitivity for gamma sources employing NaI detector arrays on board an airplane flying at 500 feet altitude is better than 2 μR/hr for surface planar contaminants and approximately 10 mCi for a point gamma source

Design and research of safety monitor and control system based on CAN BUS

International Nuclear Information System (INIS)

Wen Xinling; Chen Yu; Zhang Zhen; Zhao Yubin

2007-01-01

In Order to protect machine operator under danger work area in producing-manufacturing industry, we present a distributed safety monitor and control system based on CAN BUS technology. The detection signal is collected based on the photo-voltage characteristics of the infrared sensor and it was processed with the core of AT89C51. The microprocessor controls the CAN BUS controller SJA1000/transceiver PCA82C250 to structure CAN BUS communication system to transmit the data. Through the serial interface MAX232 connected main controller with each control node, PC can monitor and control each machine in real time and renew control scheme. This paper introduces composition principle and the methods of hardware design in detail. Experiments shown that the system has yield control precision of 0.1 mm, defend distance more than 15 m and the measurement accuracy of 100%. Moreover, it can realize to reform FA431 and monitor cotton-breaking, yarn-breaking and product quality. Productivity is improved about 25%-35%. (authors)

Safety analysis report: A comparison of incidents from Safety Years 2006 through 2010, USDA Forest Service, Rocky Mountain Research Station Inventory and Monitoring Program

Science.gov (United States)

Devon Donahue

2012-01-01

This paper is an analysis of 5 years of accident data for the USDA Forest Service, Rocky Mountain Research Station (RMRS) Inventory and Monitoring (IM) Program that identifies past trends, allows for standardized self-comparison, and increases our understanding of the true costs of injuries and accidents. Measuring safety is a difficult task. While most agree that...

Hospital survey on patient safety culture: psychometric analysis on a Scottish sample.

Science.gov (United States)

Sarac, Cakil; Flin, Rhona; Mearns, Kathryn; Jackson, Jeanette

2011-10-01

To investigate the psychometric properties of the Hospital Survey on Patient Safety Culture on a Scottish NHS data set. The data were collected from 1969 clinical staff (estimated 22% response rate) from one acute hospital from each of seven Scottish Health boards. Using a split-half validation technique, the data were randomly split; an exploratory factor analysis was conducted on the calibration data set, and confirmatory factor analyses were conducted on the validation data set to investigate and check the original US model fit in a Scottish sample. Following the split-half validation technique, exploratory factor analysis results showed a 10-factor optimal measurement model. The confirmatory factor analyses were then performed to compare the model fit of two competing models (10-factor alternative model vs 12-factor original model). An S-B scaled χ(2) square difference test demonstrated that the original 12-factor model performed significantly better in a Scottish sample. Furthermore, reliability analyses of each component yielded satisfactory results. The mean scores on the climate dimensions in the Scottish sample were comparable with those found in other European countries. This study provided evidence that the original 12-factor structure of the Hospital Survey on Patient Safety Culture scale has been replicated in this Scottish sample. Therefore, no modifications are required to the original 12-factor model, which is suggested for use, since it would allow researchers the possibility of cross-national comparisons.

Evaluation of patient safety culture among Malaysian retail pharmacists: results of a self-reported survey

Directory of Open Access Journals (Sweden)

Sivanandy P

2016-07-01

Full Text Available Palanisamy Sivanandy,1 Mari Kannan Maharajan,1 Kingston Rajiah,1 Tan Tyng Wei,2 Tan Wee Loon,2 Lim Chong Yee2 1Department of Pharmacy Practice, School of Pharmacy, 2School of Pharmacy, International Medical University, Wilayah Persekutuan Kuala Lumpur, Malaysia Background: Patient safety is a major public health issue, and the knowledge, skills, and experience of health professionals are very much essential for improving patient safety. Patient safety and medication error are very much associated. Pharmacists play a significant role in patient safety. The function of pharmacists in the medication use process is very different from medical and nursing colleagues. Medication dispensing accuracy is a vital element to ensure the safety and quality of medication use.Objective: To evaluate the attitude and perception of the pharmacist toward patient safety in retail pharmacies setup in Malaysia.Methods: A Pharmacy Survey on Patient Safety Culture questionnaire was used to assess patient safety culture, developed by the Agency for Healthcare Research and Quality, and the convenience sampling method was adopted.Results: The overall positive response rate ranged from 31.20% to 87.43%, and the average positive response rate was found to be 67%. Among all the eleven domains pertaining to patient safety culture, the scores of “staff training and skills” were less. Communication openness, and patient counseling are common, but not practiced regularly in the Malaysian retail pharmacy setup compared with those in USA. The overall perception of patient safety of an acceptable level in the current retail pharmacy setup.Conclusion: The study revealed that staff training, skills, communication in patient counseling, and communication across shifts and about mistakes are less in current retail pharmacy setup. The overall perception of patient safety should be improved by educating the pharmacists about the significance and essential of patient safety. Keywords

Configuration of Risk Monitor System by PLant Defense-In.Depth Monitor and Relability Monitor

DEFF Research Database (Denmark)

Yoshikawa, Hidekazu; Lind, Morten; Yang, Ming

2012-01-01

A new method of risk monitor system of a nuclear power plant has been proposed from the aspect by what degree of safety functions incorporated in the plant system is maintained by multiple barriers of defense-in-depth (DiD). Wherein, the central idea is plant DiD risk monitor and reliability...... monitor derived from the four aspects of (i) design principle of nuclear safety to realize DiD concept, (ii) definition of risk and risk to be monitored, (iii) severe accident phenomena as major risk, (iv) scheme of risk ranking, and (v) dynamic risk display. In this paper, the overall frame...... of the proposed frame on risk monitor system is summarized and the detailed discussion is made on the definitions of major terminologies of risk, risk ranking, anatomy of fault occurrence, two-layer configuration of risk monitor, how to configure individual elements of plant DiD risk monitor and its example...

A new standard for multidisciplinary health and safety technicians

International Nuclear Information System (INIS)

Trinoskey, P.A.; Fry, L.A.; Egbert, W.F.

2000-01-01

Over the last two decades, a significant trend in health and safety has been toward greater specialization. However, compartmentalization of health and safety disciplines often leads to an inequity in resources, especially when appropriations overemphasize one risk to the detriment of others. For example, overemphasis on radiological safety can create an imbalance in overall worker protection. A multidisciplinary technical can help restore the balance and provide for a healthier and safer work environment. The key advantages of a multidisciplinary health and safety technician include: Broad coverage of the work area by one technician, More diverse use of the technician pool, Better coverage for off-shift or nonstandard hours, Balance of risks because all hazards are considered, Integrated emergency response, Ownership, Less time of identify the correct person with the requisite skills. We have developed a new standard that establishes the training and related qualifications for a multidisciplinary health and safety technician. The areas of training and qualification that are addressed include elements of industrial hygiene, industrial safety, fire protection, electrical safety, construction safety, and radiation safety. The initial core training program ensures that individuals are trained to the performance of requirements of the job. Initial training is in five areas: Fundamentals, Hazard recognition, Hazard assessment, Hazards controls, Hazards minimization. Core training is followed by formal qualification on specific tasks, including ventilation surveys, air monitoring, noise assessments, radiological monitoring, area inspections, work-area setups, and work coverage. The new standard addresses not only training topics and requirements, but also guidance to ensure that performance objectives are met. The standard applies to technicians, supervisors, technologists, and six specialty areas, including academic institutions and decontamination and decommissioning

A new standard for multidisciplinary health and safety technicians

Energy Technology Data Exchange (ETDEWEB)

Trinoskey, P.A.; Fry, L.A. [Lawrence Livermore National Laboratory, Univ. of California, CA (United States); Egbert, W.F. [Lawrence Livermore National Laboratory, Allied Signal Technical Corporation (United States)

2000-05-01

Over the last two decades, a significant trend in health and safety has been toward greater specialization. However, compartmentalization of health and safety disciplines often leads to an inequity in resources, especially when appropriations overemphasize one risk to the detriment of others. For example, overemphasis on radiological safety can create an imbalance in overall worker protection. A multidisciplinary technical can help restore the balance and provide for a healthier and safer work environment. The key advantages of a multidisciplinary health and safety technician include: Broad coverage of the work area by one technician, More diverse use of the technician pool, Better coverage for off-shift or nonstandard hours, Balance of risks because all hazards are considered, Integrated emergency response, Ownership, Less time of identify the correct person with the requisite skills. We have developed a new standard that establishes the training and related qualifications for a multidisciplinary health and safety technician. The areas of training and qualification that are addressed include elements of industrial hygiene, industrial safety, fire protection, electrical safety, construction safety, and radiation safety. The initial core training program ensures that individuals are trained to the performance of requirements of the job. Initial training is in five areas: Fundamentals, Hazard recognition, Hazard assessment, Hazards controls, Hazards minimization. Core training is followed by formal qualification on specific tasks, including ventilation surveys, air monitoring, noise assessments, radiological monitoring, area inspections, work-area setups, and work coverage. The new standard addresses not only training topics and requirements, but also guidance to ensure that performance objectives are met. The standard applies to technicians, supervisors, technologists, and six specialty areas, including academic institutions and decontamination and decommissioning

Development of IoT-based Urban Sinkhole and Road Collapse Monitoring System

Science.gov (United States)

Jung, B.; Bang, E.; Lee, H. J.; Jeong, S. W.; Ryu, D.; Kim, S. W.; Kim, B. K.; Yum, B. W.; Lee, I. H.

2015-12-01

The consortium of Korean government-funded research institutes is developing IoT- (Internet of things) based underground safety monitoring and alerting system to manage risks arisen from land subsidence and road collapses in metropolitan areas in South Korea. The system consists of four major functional units: subsurface monitoring sensors sending data directly through the internet, centralized servers capable of collecting and processing big data, computational modules providing physical and statistical models for predicting high-risk areas, and geologic information service platforms visualizing underground safety maps for the public. The target urban area will be regionally covered by multi-sensors monitoring soil and groundwater conditions, and by high resolution satellite InSAR images filtering vertical land movements in a centimeter scale. Integrity of buried water supply and sewer lines are also monitored for the possibility of underground cavity formation. Once high-risk area is predicted, more tangible surveying methods such as ground penetrating radar (GPR) and resistivity survey can be applied for locating the cavities. Additionally, laboratory and field experiments are performed to understand overall road collapsing mechanism from the initial cavity creation to its progressive development depending on soil types, degree of compaction, and groundwater condition. Acquired results will update existing fully-coupled hydromechanical models for more accurate prediction of the collapsing-vulnerable area. Preliminary laboratory experiments show that the upward propagation of subsurface cavity is closely related to the soil properties, such as sand-clay ratios and moisture contents, and groundwater dynamics.

Rule-based Dynamic Safety Monitoring for Mobile Robots

DEFF Research Database (Denmark)

Adam, Marian Sorin; Larsen, Morten; Jensen, Kjeld

2016-01-01

—Safety is a key challenge in robotics, in particular for mobile robots operating in an open and unpredictable environment. Safety certification is desired for commercial robots, but no existing approaches for addressing the safety challenge provide a clearly specified and isolated safety layer......, defined in an easily understandable way for facilitating safety certification. In this paper, we propose that functional-safety-critical concerns regarding the robot software be explicitly declared separately from the main program, in terms of externally observable properties of the software. Concretely...

Eight years of the Great Influenza Survey to monitor influenza-like illness in Flanders.

Directory of Open Access Journals (Sweden)

Yannick Vandendijck

Full Text Available In 2003, an internet-based monitoring system of influenza-like illness (ILI, the Great Influenza Survey (GIS, was initiated in Belgium. For the Flemish part of Belgium, we investigate the representativeness of the GIS population and assess the validity of the survey in terms of ILI incidence during eight influenza seasons (from 2003 through 2011. The validity is investigated by comparing estimated ILI incidences from the GIS with recorded incidences from two other monitoring systems, (i the Belgian Sentinel Network and (ii the Google Flu Trends, and by performing a risk factor analysis to investigate whether the risks on acquiring ILI in the GIS population are comparable with results in the literature. A random walk model of first order is used to estimate ILI incidence trends based on the GIS. Good to excellent correspondence is observed between the estimated ILI trends in the GIS and the recorded trends in the Sentinel Network and the Google Flu Trends. The results of the risk factor analysis are in line with the literature. In conclusion, the GIS is a useful additional surveillance network for ILI monitoring in Flanders. The advantages are the speed at which information is available and the fact that data is gathered directly in the community at an individual level.

Systematic survey for monitor signals to reduce fake burst events in a gravitational-wave detector

International Nuclear Information System (INIS)

Ishidoshiro, Koji; Ando, Masaki; Tsubono, Kimio

2006-01-01

We present methods and results to reduce fake burst events induced by nonstationary noises. To reduce these fake events, we systematically surveyed monitor signals recorded with a main (or gravitational-wave) signal of a gravitational-wave detector so as to watch the detector. Our survey was to check whether or not there was a coincidence between the main and monitor signals when we found a burst event from the main signal. If there was a coincidence, we rejected this event as a fake event induced by nonstationary noises, regarding the main signal as being dominated by nonstationary noises. As a result, we succeeded to reject about 90% of the burst events of which the SNR values were larger than 10 as fake events, with an accidental probability of about 5% to reject burst-gravitational-wave candidates

Road Safety Data, Collection, Transfer and Analysis DaCoTa. Workpackage 6, Driver Behaviour Monitoring through Naturalistic Driving: Deliverable 6.3: Report on small scale naturalistic driving pilot.

NARCIS (Netherlands)

Pilgerstorfer, M. Runda, K. Brandstätter, C. Christoph, M. Hakkert, S. Ishaq, R. Toledo, T. & Gatscha, M.

2012-01-01

WP6 of DaCoTA, Driver Behaviour Monitoring through Naturalistic Driving, aims to develop an implementation plan for a large scale activity that uses Naturalistic Driving (ND) Observations to continuously monitor relevant road safety data within the framework of the European Road Safety Observatory.

Does Employee Safety Matter for Patients Too? Employee Safety Climate and Patient Safety Culture in Health Care.

Science.gov (United States)

Mohr, David C; Eaton, Jennifer Lipkowitz; McPhaul, Kathleen M; Hodgson, Michael J

2015-04-22

We examined relationships between employee safety climate and patient safety culture. Because employee safety may be a precondition for the development of patient safety, we hypothesized that employee safety culture would be strongly and positively related to patient safety culture. An employee safety climate survey was administered in 2010 and assessed employees' views and experiences of safety for employees. The patient safety survey administered in 2011 assessed the safety culture for patients. We performed Pearson correlations and multiple regression analysis to examine the relationships between a composite measure of employee safety with subdimensions of patient safety culture. The regression models controlled for size, geographic characteristics, and teaching affiliation. Analyses were conducted at the group level using data from 132 medical centers. Higher employee safety climate composite scores were positively associated with all 9 patient safety culture measures examined. Standardized multivariate regression coefficients ranged from 0.44 to 0.64. Medical facilities where staff have more positive perceptions of health care workplace safety climate tended to have more positive assessments of patient safety culture. This suggests that patient safety culture and employee safety climate could be mutually reinforcing, such that investments and improvements in one domain positively impacts the other. Further research is needed to better understand the nexus between health care employee and patient safety to generalize and act upon findings.

Impact of the Global Food Safety Initiative on Food Safety Worldwide: Statistical Analysis of a Survey of International Food Processors.

Science.gov (United States)

Crandall, Philip G; Mauromoustakos, Andy; O'Bryan, Corliss A; Thompson, Kevin C; Yiannas, Frank; Bridges, Kerry; Francois, Catherine

2017-10-01

In 2000, the Consumer Goods Forum established the Global Food Safety Initiative (GFSI) to increase the safety of the world's food supply and to harmonize food safety regulations worldwide. In 2013, a university research team in conjunction with Diversey Consulting (Sealed Air), the Consumer Goods Forum, and officers of GFSI solicited input from more than 15,000 GFSI-certified food producers worldwide to determine whether GFSI certification had lived up to these expectations. A total of 828 usable questionnaires were analyzed, representing about 2,300 food manufacturing facilities and food suppliers in 21 countries, mainly across Western Europe, Australia, New Zealand, and North America. Nearly 90% of these certified suppliers perceived GFSI as being beneficial for addressing their food safety concerns, and respondents were eight times more likely to repeat the certification process knowing what it entailed. Nearly three-quarters (74%) of these food manufacturers would choose to go through the certification process again even if certification were not required by one of their current retail customers. Important drivers for becoming GFSI certified included continuing to do business with an existing customer, starting to do business with new customer, reducing the number of third-party food safety audits, and continuing improvement of their food safety program. Although 50% or fewer respondents stated that they saw actual increases in sales, customers, suppliers, or employees, significantly more companies agreed than disagreed that there was an increase in these key performance indicators in the year following GFSI certification. A majority of respondents (81%) agreed that there was a substantial investment in staff time since certification, and 50% agreed there was a significant capital investment. This survey is the largest and most representative of global food manufacturers conducted to date.

Major food safety episodes in Taiwan: implications for the necessity of international collaboration on safety assessment and management.

Science.gov (United States)

Li, Jih-Heng; Yu, Wen-Jing; Lai, Yuan-Hui; Ko, Ying-Chin

2012-07-01

The major food safety episodes that occurred in Taiwan during the past decade are briefly reviewed in this paper. Among the nine major episodes surveyed, with the exception of a U.S. beef (associated with Creutzfeldt-Jakob disease)-related incident, all the others were associated with chemical toxicants. The general public, which has a layperson attitude of zero tolerance toward food safety, may panic over these food-safety-associated incidents. However, the health effects and impacts of most incidents, with the exception of the melamine incident, were essentially not fully evaluated. The mass media play an important role in determining whether a food safety concern becomes a major incident. A well-coordinated and harmonized system for domestic and international collaboration to set up standards and regulations is critical, as observed in the incidents of pork with ractopamine, Chinese hairy crab with nitrofuran antibiotics, and U.S. wheat with malathion. In the future, it can be anticipated that food safety issues will draw more attention from the general public. For unknown new toxicants or illicit adulteration of food, the establishment of a more proactive safety assessment system to monitor potential threats and provide real-time information exchange is imperative. Copyright © 2012. Published by Elsevier B.V.

School Survey on Crime and Safety (SSOCS): 2015-16. Public-Use Data File User's Manual. NCES 2018-107

Science.gov (United States)

Jackson, Michael; Diliberti, Melissa; Kemp, Jana; Hummel, Steven; Cox, Christina; Gbondo-Tugbawa, Komba; Simon, Dillon

2018-01-01

The School Survey on Crime and Safety (SSOCS) is managed by the National Center for Education Statistics (NCES) within the Institute of Education Sciences of the U.S. Department of Education. SSOCS collects extensive crime and safety data from principals and administrators of public schools in the United States. Data from this collection can be…

Radiation Safety in Industrial Radiography. Specific Safety Guide (Spanish Edition)

International Nuclear Information System (INIS)

2013-01-01

This Safety Guide provides recommendations for ensuring radiation safety in industrial radiography used in non-destructive testing. This includes industrial radiography work that utilizes X ray and gamma sources, both in shielded facilities that have effective engineering controls and in outside shielded facilities using mobile sources. Contents: 1. Introduction; 2. Duties and responsibilities; 3. Safety assessment; 4. Radiation protection programme; 5. Training and qualification; 6. Individual monitoring of workers; 7. Workplace monitoring; 8. Control of radioactive sources; 9. Safety of industrial radiography sources and exposure devices; 10. Radiography in shielded enclosures; 11. Site radiography; 12. Transport of radioactive sources; 13. Emergency preparedness and response; Appendix: IAEA categorization of radioactive sources; Annex I: Example safety assessment; Annex II: Overview of industrial radiography sources and equipment; Annex III: Examples of accidents in industrial radiography

Radiation Safety in Industrial Radiography. Specific Safety Guide (French Edition)

International Nuclear Information System (INIS)

2013-01-01

This Safety Guide provides recommendations for ensuring radiation safety in industrial radiography used in non-destructive testing. This includes industrial radiography work that utilizes X ray and gamma sources, both in … shielded facilities that have effective engineering controls and in outside shielded facilities using mobile sources. Contents: 1. Introduction; 2. Duties and responsibilities; 3. Safety assessment; 4. Radiation protection programme; 5. Training and qualification; 6. Individual monitoring of workers; 7. Workplace monitoring; 8. Control of radioactive sources; 9. Safety of industrial radiography sources and exposure devices; 10. Radiography in shielded enclosures; 11. Site radiography; 12. Transport of radioactive sources; 13. Emergency preparedness and response; Appendix: IAEA categorization of radioactive sources; Annex I: Example safety assessment; Annex II: Overview of industrial radiography sources and equipment; Annex III: Examples of accidents in industrial radiography

Radiation Safety in Industrial Radiography. Specific Safety Guide (Arabic Edition)

International Nuclear Information System (INIS)

2012-01-01

This Safety Guide provides recommendations for ensuring radiation safety in industrial radiography used in non-destructive testing. This includes industrial radiography work that utilizes X ray and gamma sources, both in shielded facilities that have effective engineering controls and outside shielded facilities using mobile sources. Contents: 1. Introduction; 2. Duties and responsibilities; 3. Safety assessment; 4. Radiation protection programme; 5. Training and qualification; 6. Individual monitoring of workers; 7. Workplace monitoring; 8. Control of radioactive sources; 9. Safety of industrial radiography sources and exposure devices; 10. Radiography in shielded enclosures; 11. Site radiography; 12. Transport of radioactive sources; 13. Emergency preparedness and response; Appendix: IAEA categorization of radioactive sources; Annex I: Example safety assessment; Annex II: Overview of industrial radiography sources and equipment; Annex III: Examples of accidents in industrial radiography.

The safety monitor and RCM workstation as complementary tools in risk based maintenance optimization

International Nuclear Information System (INIS)

Rawson, P.D.

2000-01-01

Reliability Centred Maintenance (RCM) represents a proven technique for rendering maintenance activities safer, more effective, and less expensive, in terms of systems unavailability and resource management. However, it is believed that RCM can be enhanced by the additional consideration of operational plant risk. This paper discusses how two computer-based tools, i.e., the RCM Workstation and the Safety Monitor, can complement each other in helping to create a living preventive maintenance strategy. (author)

Nursing assessment of continuous vital sign surveillance to improve patient safety on the medical/surgical unit.

Science.gov (United States)

Watkins, Terri; Whisman, Lynn; Booker, Pamela

2016-01-01

Evaluate continuous vital sign surveillance as a tool to improve patient safety in the medical/surgical unit. Failure-to-rescue is an important measure of hospital quality. Patient deterioration is often preceded by changes in vital signs. However, continuous multi-parameter vital sign monitoring may decrease patient safety with an abundance of unnecessary alarms. Prospective observational study at two geographically disperse hospitals in a single hospital system. A multi-parameter vital sign monitoring system was installed in a medical/surgical unit in Utah and one in Alabama providing continuous display of SpO2, heart rate, blood pressure and respiration rate on a central station. Alarm thresholds and time to alert annunciations were set based on prior analysis of the distribution of each vital sign. At the end of 4 weeks, nurses completed a survey on their experience. An average alert per patient, per day was determined retrospectively from the saved vital signs data and knowledge of the alarm settings. Ninety-two per cent of the nurses agreed that the number of alarms and alerts were appropriate; 54% strongly agreed. On average, both units experienced 10·8 alarms per patient, per day. One hundred per cent agreed the monitor provided valuable patient data that increased patient safety; 79% strongly agreed. Continuous, multi-parameter patient monitoring could be performed on medical/surgical units with a small and appropriate level of alarms. Continuous vital sign assessment may have initiated nursing interventions that prevented failure-to-rescue events. Nurses surveyed unanimously agreed that continuous vital sign surveillance will help enhance patient safety. Nursing response to abnormal vital signs is one of the most important levers in patient safety, by providing timely recognition of early clinical deterioration. This occurs through diligent nursing surveillance, involving assessment, interpretation of data, recognition of a problem and meaningful

Utilizing data consortia to monitor safety and effectiveness of biosimilars and their innovator products.

Science.gov (United States)

Baldziki, Mike; Brown, Jeff; Chan, Hungching; Cheetham, T Craig; Conn, Thomas; Daniel, Gregory W; Hendrickson, Mark; Hilbrich, Lutz; Johnson, Ayanna; Miller, Steven B; Moore, Tom; Motheral, Brenda; Priddy, Sarah A; Raebel, Marsha A; Randhawa, Gurvaneet; Surratt, Penny; Walraven, Cheryl; White, T Jeff; Bruns, Kevin; Carden, Mary Jo; Dragovich, Charlie; Eichelberger, Bernadette; Rosato, Edith; Sega, Todd

2015-01-01

The Biologics Price Competition and Innovation Act, introduced as part of the Affordable Care Act, directed the FDA to create an approval pathway for biologic products shown to be biosimilar or interchangeable with an FDA-approved innovator drug. These biosimilars will not be chemically identical to the reference agent. Investigational studies conducted with biosimilar agents will likely provide limited real-world evidence of their effectiveness and safety. How do we best monitor effectiveness and safety of biosimilar products once approved by the FDA and used more extensively by patients? To determine the feasibility of developing a distributed research network that will use health insurance plan and health delivery system data to detect biosimilar safety and effectiveness signals early and be able to answer important managed care pharmacy questions from both the government and managed care organizations. Twenty-one members of the AMCP Task Force on Biosimilar Collective Intelligence Systems met November 12, 2013, to discuss issues involved in designing this consortium and to explore next steps. The task force concluded that a managed care biosimilars research consortium would be of significant value. Task force members agreed that it is best to use a distributed research network structurally similar to existing DARTNet, HMO Research Network, and Mini-Sentinel consortia. However, for some surveillance projects that it undertakes, the task force recognizes it may need supplemental data from managed care and other sources (i.e., a "hybrid" structure model). The task force believes that AMCP is well positioned to lead the biosimilar-monitoring effort and that the next step to developing a biosimilar-innovator collective intelligence system is to convene an advisory council to address organizational governance.

The impact of nurse working hours on patient safety culture: a cross-national survey including Japan, the United States and Chinese Taiwan using the Hospital Survey on Patient Safety Culture.

Science.gov (United States)

Wu, Yinghui; Fujita, Shigeru; Seto, Kanako; Ito, Shinya; Matsumoto, Kunichika; Huang, Chiu-Chin; Hasegawa, Tomonori

2013-10-07

A positive patient safety culture (PSC) is one of the most critical components to improve healthcare quality and safety. The Hospital Survey on Patient Safety Culture (HSOPS), developed by the US Agency for Healthcare Research and Quality, has been used to assess PSC in 31 countries. However, little is known about the impact of nurse working hours on PSC. We hypothesized that long nurse working hours would deteriorate PSC, and that the deterioration patterns would vary between countries. Moreover, the common trends observed in Japan, the US and Chinese Taiwan may be useful to improve PSC in other countries. The purpose of this study was to clarify the impact of long nurse working hours on PSC in Japan, the US, and Chinese Taiwan using HSOPS. The HSOPS questionnaire measures 12 sub-dimensions of PSC, with higher scores indicating a more positive PSC. Odds ratios (ORs) were calculated using a generalized linear mixed model to evaluate the impact of working hours on PSC outcome measures (patient safety grade and number of events reported). Tukey's test and Cohen's d values were used to verify the relationships between nurse working hours and the 12 sub-dimensions of PSC. Nurses working ≥60 h/week in Japan and the US had a significantly lower OR for patient safety grade than those working working ≥40 h/week had a significantly higher OR for the number of events reported. The mean score on 'staffing' was significantly lower in the ≥60-h group than in the Japan and Chinese Taiwan. Patient safety grade deteriorated and the number of events reported increased with long working hours. Among the 12 sub-dimensions of PSC, long working hours had an impact on 'staffing' and 'teamwork within units' in Japan, the US and Chinese Taiwan.

Perception of risks and safety. Results of the November 2002 survey

International Nuclear Information System (INIS)

2002-01-01

After having recalled the themes present in the survey on the perception of risks and safety as far as nuclear energy is concerned, this report proposes an analysis of the obtained results. It discusses the current general concerns, the perception of risks (risks for the society, confidence in authorities, spoken truth), the opinions on the scientific expertise (role, opinion, confidence), the perception of technological and natural risks for the environment (hazardous installations, demand for environmental acceptability of installations, participation to information session, industrial and natural disasters), the opinions on nuclear activities (image, actors, information, control of these activities), and finally the possibility of a nuclear accident and the implemented countermeasures

Comparison of hoop-net trapping and visual surveys to monitor abundance of the Rio Grande cooter (Pseudemys gorzugi

Directory of Open Access Journals (Sweden)

Ivana Mali

2018-05-01

Full Text Available Abundance estimates play an important part in the regulatory and conservation decision-making process. It is important to correct monitoring data for imperfect detection when using these data to track spatial and temporal variation in abundance, especially in the case of rare and elusive species. This paper presents the first attempt to estimate abundance of the Rio Grande cooter (Pseudemys gorzugi while explicitly considering the detection process. Specifically, in 2016 we monitored this rare species at two sites along the Black River, New Mexico via traditional baited hoop-net traps and less invasive visual surveys to evaluate the efficacy of these two sampling designs. We fitted the Huggins closed-capture estimator to estimate capture probabilities using the trap data and distance sampling models to estimate detection probabilities using the visual survey data. We found that only the visual survey with the highest number of observed turtles resulted in similar abundance estimates to those estimated using the trap data. However, the estimates of abundance from the remaining visual survey data were highly variable and often underestimated abundance relative to the estimates from the trap data. We suspect this pattern is related to changes in the basking behavior of the species and, thus, the availability of turtles to be detected even though all visual surveys were conducted when environmental conditions were similar. Regardless, we found that riverine habitat conditions limited our ability to properly conduct visual surveys at one site. Collectively, this suggests visual surveys may not be an effective sample design for this species in this river system. When analyzing the trap data, we found capture probabilities to be highly variable across sites and between age classes and that recapture probabilities were much lower than initial capture probabilities, highlighting the importance of accounting for detectability when monitoring this species

Safety and environmental health handbook

Science.gov (United States)

,

1989-01-01

This Safety Handbook (445-1-H.) supplements the Geological Survey Safety Management Program objectives set forth in Survey Manual 445.1. Specifically, it provides a compact source of basic information to assist management and employees in preventing motor vehicle accidents, personal injuries, occupational diseases, fire, and other property damage or loss. All work situations incidental to the Geological Survey cannot be discussed in a handbook, and such complete coverage is not intended in this document. However, a wide range of subjects are covered in which a "common sense" approach to safety has been expressed. These subjects have been organized such that Chapters 1-5 address administrative issues, Chapters 6-12 address activities usually conducted within a facility, and Chapters 13-20 address field activities. No information contained in the Handbook is intended to alter any provision of any Federal law or executive order, Department of the Interior or Survey directive, or collective bargaining agreement. Questions or suggestions regarding the content of the Safety Handbook may be directed to the Survey Safety Manager, Administrative Division, Office of Facilities and Management Services, National Center, Reston, Virginia, Mail Stop 246. The previous edition of the Safety Handbook is superseded.

Disease Risk Perception and Safety Practices: A Survey of Australian Flying Fox Rehabilitators.

Directory of Open Access Journals (Sweden)

Cecilia A Sánchez

2016-02-01

Full Text Available Interactions with flying foxes pose disease transmission risks to volunteer rehabilitators (carers who treat injured, ill, and orphaned bats. In particular, Australian bat lyssavirus (ABLV can be transmitted directly from flying foxes to humans in Australia. Personal protective equipment (PPE and rabies vaccination can be used to protect against lyssavirus infection. During May and June 2014, active Australian flying fox carers participated in an online survey (SOAR: Survey Of Australian flying fox Rehabilitators designed to gather demographic data, assess perceptions of disease risk, and explore safety practices. Responses to open-ended questions were analysed thematically. A logistic regression was performed to assess whether rehabilitators' gender, use of PPE, threat perception, and years of experience predicted variation in their odds of being bitten or scratched. Eligible responses were received from 122 rehabilitators located predominantly on the eastern coast of Australia. Eighty-four percent of respondents were female. Years of experience ranged from <1 to 30 years (median 5 years. Respondents were highly educated. All rehabilitators were vaccinated against rabies and 94% received a rabies titre check at least every two years. Sixty-three percent of carers did not perceive viruses in flying foxes as a potential threat to their health, yet 74% of carers reported using PPE when handling flying foxes. Eighty-three percent of rehabilitators had received a flying fox bite or scratch at some point during their career. Carers provide an important community service by rescuing and rehabilitating flying foxes. While rehabilitators in this study have many excellent safety practices, including a 100% vaccination rate against rabies, there is room for improvement in PPE use. We recommend 1 the establishment of an Australia-wide set of guidelines for safety when caring for bats and 2 that the responsible government agencies in Australia support

Road Safety Data, Collection, Transfer and Analysis DaCoTa. Workpackage 6, Driver Behaviour Monitoring through Naturalistic Driving: Deliverable 6.5: Naturalistic Driving for cross-national monitoring of SPIs and Exposure : an overview.

NARCIS (Netherlands)

Wegman, R.W.N. & Bos, N.M.

2015-01-01

WP6 of DaCoTA, Driver Behaviour Monitoring through Naturalistic Driving, focuses on the usefulness and feasibility of applying the Naturalistic Driving method for monitoring within the framework of ERSO. The aim is to continuously collect comparable information about the road safety level in EU

Survey and evaluation of inherent safety characteristics and passive safety systems for use in probabilistic safety analyses

International Nuclear Information System (INIS)

Wetzel, N.; Scharfe, A.

1998-01-01

The present report examines the possibilities and limits of a probabilistic safety analysis to evaluate passive safety systems and inherent safety characteristics. The inherent safety characteristics are based on physical principles, that together with the safety system lead to no damage. A probabilistic evaluation of the inherent safety characteristic is not made. An inventory of passive safety systems of accomplished nuclear power plant types in the Federal Republic of Germany was drawn up. The evaluation of the passive safety system in the analysis of the accomplished nuclear power plant types was examined. The analysis showed that the passive manner of working was always assumed to be successful. A probabilistic evaluation was not performed. The unavailability of the passive safety system was determined by the failure of active components which are necessary in order to activate the passive safety system. To evaluate the passive safety features in new concepts of nuclear power plants the AP600 from Westinghouse, the SBWR from General Electric and the SWR 600 from Siemens, were selected. Under these three reactor concepts, the SWR 600 is specially attractive because the safety features need no energy sources and instrumentation in this concept. First approaches for the assessment of the reliability of passively operating systems are summarized. Generally it can be established that the core melt frequency for the passive concepts AP600 and SBWR is advantageous in comparison to the probabilistic objectives from the European Pressurized Water Reactor (EPR). Under the passive concepts is the SWR 600 particularly interesting. In this concept the passive systems need no energy sources and instrumentation, and has active operational systems and active safety equipment. Siemens argues that with this concept the frequency of a core melt will be two orders of magnitude lower than for the conventional reactors. (orig.) [de

Patient safety culture among nurses.

Science.gov (United States)

Ammouri, A A; Tailakh, A K; Muliira, J K; Geethakrishnan, R; Al Kindi, S N

2015-03-01

Patient safety is considered to be crucial to healthcare quality and is one of the major parameters monitored by all healthcare organizations around the world. Nurses play a vital role in maintaining and promoting patient safety due to the nature of their work. The purpose of this study was to investigate nurses' perceptions about patient safety culture and to identify the factors that need to be emphasized in order to develop and maintain the culture of safety among nurses in Oman. A descriptive and cross-sectional design was used. Patient safety culture was assessed by using the Hospital Survey on Patient Safety Culture among 414 registered nurses working in four major governmental hospitals in Oman. Descriptive statistics and general linear regression were employed to assess the association between patient safety culture and demographic variables. Nurses who perceived more supervisor or manager expectations, feedback and communications about errors, teamwork across hospital units, and hospital handoffs and transitions had more overall perception of patient safety. Nurses who perceived more teamwork within units and more feedback and communications about errors had more frequency of events reported. Furthermore, nurses who had more years of experience and were working in teaching hospitals had more perception of patient safety culture. Learning and continuous improvement, hospital management support, supervisor/manager expectations, feedback and communications about error, teamwork, hospital handoffs and transitions were found to be major patient safety culture predictors. Investing in practices and systems that focus on improving these aspects is likely to enhance the culture of patient safety in Omani hospitals and others like them. Strategies to nurture patient safety culture in Omani hospitals should focus upon building leadership capacity that support open communication, blame free, team work and continuous organizational learning. © 2014 International

Classification of Variable Objects in Massive Sky Monitoring Surveys

Science.gov (United States)

Woźniak, Przemek; Wyrzykowski, Łukasz; Belokurov, Vasily

2012-03-01

The era of great sky surveys is upon us. Over the past decade we have seen rapid progress toward a continuous photometric record of the optical sky. Numerous sky surveys are discovering and monitoring variable objects by hundreds of thousands. Advances in detector, computing, and networking technology are driving applications of all shapes and sizes ranging from small all sky monitors, through networks of robotic telescopes of modest size, to big glass facilities equipped with giga-pixel CCD mosaics. The Large Synoptic Survey Telescope will be the first peta-scale astronomical survey [18]. It will expand the volume of the parameter space available to us by three orders of magnitude and explore the mutable heavens down to an unprecedented level of sensitivity. Proliferation of large, multidimensional astronomical data sets is stimulating the work on new methods and tools to handle the identification and classification challenge [3]. Given exponentially growing data rates, automated classification of variability types is quickly becoming a necessity. Taking humans out of the loop not only eliminates the subjective nature of visual classification, but is also an enabling factor for time-critical applications. Full automation is especially important for studies of explosive phenomena such as γ-ray bursts that require rapid follow-up observations before the event is over. While there is a general consensus that machine learning will provide a viable solution, the available algorithmic toolbox remains underutilized in astronomy by comparison with other fields such as genomics or market research. Part of the problem is the nature of astronomical data sets that tend to be dominated by a variety of irregularities. Not all algorithms can handle gracefully uneven time sampling, missing features, or sparsely populated high-dimensional spaces. More sophisticated algorithms and better tools available in standard software packages are required to facilitate the adoption of

Crude versus case-mix-adjusted control charts for safety monitoring in thyroid surgery.

Science.gov (United States)

Duclos, Antoine; Voirin, Nicolas; Touzet, Sandrine; Soardo, Pietro; Schott, Anne-Marie; Colin, Cyrille; Peix, Jean-Louis; Lifante, Jean-Christophe

2010-12-01

Patient-safety monitoring based on health-outcome indicators can lead to misinterpretation of changes in case mix. This study aimed to compare the detection of indicator variations between crude and case-mix-adjusted control charts using data from thyroid surgeries. The study population included each patient who underwent thyroid surgery in a teaching hospital from January 2006 to May 2008. Patient safety was monitored according to two indicators, which are immediately recognisable postoperative complications: recurrent laryngeal nerve palsy and hypocalcaemia. Each indicator was plotted monthly on a p-control chart using exact limits. The weighted κ statistic was calculated to measure the agreement between crude and case-mix-adjusted control charts. We evaluated the outcomes of 1405 thyroidectomies. The overall proportions of immediate recurrent laryngeal nerve palsy and hypocalcaemia were 7.4% and 20.5%, respectively. The proportion of agreement in the detection of indicator variations between the crude and case-mix-adjusted p-charts was 95% (95% CI 85% to 99%). The strength of the agreement was κ = 0.76 (95% CI 0.54 to 0.98). The single special cause of variation that occurred was only detected by the case-mix-adjusted p-chart. There was good agreement in the detection of indicator variations between crude and case-mix-adjusted p-charts. The joint use of crude and adjusted charts seems to be a reasonable approach to increase the accuracy of interpretation of variations in outcome indicators.

Practice gaps in patient safety among dermatology residents and their teachers: a survey study of dermatology residents.

Science.gov (United States)

Swary, Jillian Havey; Stratman, Erik J

2014-07-01

Curriculum and role modeling adjustments are necessary to address patient safety gaps occurring during dermatology residency. To identify the source of clinical practices among dermatology residents that affect patient safety and determine the best approach for overcoming gaps in knowledge and practice patterns that contribute to these practices. A survey-based study, performed at a national medical dermatology meeting in Itasca, Illinois, in 2012, included 142 dermatology residents from 44 residency programs in the United States and Canada. Self-reported rates of dermatology residents committing errors, identifying local systems errors, and identifying poor patient safety role modeling. Of surveyed dermatology residents, 45.2% have failed to report needle-stick injuries incurred during procedures, 82.8% reported cutting and pasting a previous author's patient history information into a medical record without confirming its validity, 96.7% reported right-left body part mislabeling during examination or biopsy, and 29.4% reported not incorporating clinical photographs of lesions sampled for biopsy in the medical record at their institution. Residents variably perform a purposeful pause ("time-out") when indicated to confirm patient, procedure, and site before biopsy, with 20.0% always doing so. In addition, 59.7% of residents work with at least 1 attending physician who intimidates the residents, reducing the likelihood of reporting safety issues they witness. Finally, 78.3% have witnessed attending physicians purposefully disregarding required safety steps. Our data reinforce the need for modified curricula, systems, and teacher development to reduce injuries, improve communication with patients and between physicians, residents, and other members of the health care team, and create an environment free of intimidation.

Guide for monitoring effectiveness of utility Reliability Centered Maintenance (RCM) programs

International Nuclear Information System (INIS)

Midgett, W.D.; Wilson, J.F.; Krochmal, D.F.; Owsenek, L.W.

1991-02-01

Reliability centered maintenance (RCM) programs help utilities optimize preventive maintenance efforts while improving plant safety and economy through increased dependability of plant components. The project team developed this guide and accompanying methodology based on status updates from the Ginna and San Onofre demonstration projects. These updates addressed areas ranging from system selection to the effectiveness of RCM program implementation. In addition, the team incorporated information from a 12-utility survey soliciting opinions on the need for a methodology to monitor RCM cost-effectiveness. An analysis of the 12-utility survey showed that no techniques had been developed to measure RCM program cost-effectiveness. Thus, this guide addresses two key areas: Pros and cons of various monitoring techniques available to assess the overall effectiveness of RCM and a methodology for specifically evaluating the cost-effectiveness of RCM programs. 1 fig

Undersafe: Monitoring safety parameters in touristic mines and caves

Science.gov (United States)

Parcerisa, David; Sanmiquel, Lluís; Alfonso, Pura; Oliva, Josep

2014-05-01

Tourism is a key sector of the European economy, generating more than 5% of the EU GPD (Gross Domestic Product). Usually, underground touristic sites receive non-expert visitors; nevertheless these activities are poorly regulated or completely deregulated. Nowadays, safety is provided by underground expert professionals whom proceed to regular inspections and by basic safety infrastructures. Even with these measures, some potential personal and environmental dangers are always present and cannot be totally avoided. Therefore, there is a clear need of a new technological product for safety and environmental continuous monitoring of tourist underground attractions. So, the aim of the Undersafe project is to provide underground attractions with a novel and specifically tailored monitoring system, easy to use and maintain. One of the goals of the Undersafe project is to develop a rock falling detection based on a set of cost limited vibration sensors. Based on the technical needs, but with cost constraints, different types of potential sensors are considered: Underground microphone: It is placed in the surface or in the underground. It is based on the consideration that the impact of the stone generates a ground impact vibration which can be understood as a "noise" that is received by a microphone capsule. Airborne sound sensing microphone: It similarly applies to underground use of the microphones, but now the microphone is tested as for its traditional use (I.e. air sound detection). In such case, the microphone detects the environmental noise produced by the impact of the stone falling onto the ground, which will include the impact sound of the stone. Geophone: It is the de facto standard for ground vibrations. Although this technology was initially discarded due to its high cost, recently, low cost geophones have appeared in the market that allows its use inside the underground attractions. Accelerometers: These, can have enough sensibility to act as vibration

On-line monitoring system for I-131 manufacturing labs

International Nuclear Information System (INIS)

Osovizky, A.; Malamud, Y.; Paran, Y.; Tal, N.; Turgeman, S.; Weinstein, M.

1997-01-01

An on-line monitoring and safety system has been installed in a lab for manufacturing 1-131 capsules for nuclear medicine use. Production of up to 100mCi batches is performed in shielded glove boxes. The safety system is based on a unique, 'Medi SMARTS' system (Medical Survey Mapping Automatic Radiation Tracing System), that collects continuously the radiation measurements for processing, display, and storage for future retrieval. Radiation is measured by GM tubes, data is transferred to a data processing unit, and then via a RS-485 communication line to a computer. In addition to the operational advantages and radiation levels storage, the system is being evaluated for the purpose of identifying risky stages in the process. (authors)

A survey of food safety training in small food manufacturers.

Science.gov (United States)

Worsfold, Denise

2005-08-01

A survey of food safety training was conducted in small food manufacturing firms in South Wales. Structured interviews with managers were used to collect information on the extent and level of food hygiene and HACCP training and the manager's perceptions of and attitude towards training. All the businesses surveyed had undertaken some hygiene training. Hygiene induction programmes were often unstructured and generally unrecorded. Low-risk production workers were usually trained on the job whilst high-care production staff were trained in hygiene to Level 1. Part-time and temporary staff received less training than full-timers. Regular refresher training was undertaken by less than half of the sample. None of the businesses made use of National Vocational Qualification (NVQ) qualifications. Over half of the managers/senior staff had undertaken higher levels of hygiene training and half had attended a HACCP course. Managers trained the workforce to operate the HACCP system. Formal training-related activities were generally only found in the larger businesses. Few of the manufacturers had made use of training consultants. Managers held positive attitudes towards training but most regarded it as operating expense rather than an investment. Resource poverty, in terms of time and money was perceived to be a major inhibiting factor to continual, systematic training.

Guidelines for environmental monitoring after acute oil spill in the marine environment; Retningslinjer for miljoeundersoekelser i marint miljoe etter akutt oljeforurensning

Energy Technology Data Exchange (ETDEWEB)

Joergensen, N.M.; Camus, L.-H.; Larsen, B.; Voegele, G.M.; Spikkerud, C.; Anker-Nilsen, T.; Dijk, J van; Lorentsen, S.-H.; Stabbetorp, O.; Bjoerge, A.; Boitsov, S.; Klungsoeyr, J.

2012-07-01

Contents of environmental damage assessments and monitoring of acute oil spills in the marine environment are outlined. The guideline provides general advice on timing, contents and scope of post spill surveys for documenting biological recovery and food safety.(Author)

SU-D-201-07: A Survey of Radiation Oncology Residents’ Training and Preparedness to Lead Patient Safety Programs in Clinics

International Nuclear Information System (INIS)

Spraker, M; Nyflot, M; Ford, E; Kane, G; Zeng, J; Hendrickson, K