Using haptic feedback to increase seat belt use : traffic tech.

Science.gov (United States)

2011-07-01

The legacy of research on increasing seat belt use has : focused on enactment of seat belt legislation, public education, : high-visibility police enforcement, and seat belt : reminder systems. Several behavioral programs have : produced large, susta...

Availability, functionality, and use of seat belts in Beijing taxis prior to the 2008 Beijing Olympic Games.

Science.gov (United States)

Fleiter, Judy J; Gao, Liping; Qiu, Chen; Shi, Kan

2009-03-01

Use of driver seat belts and availability and functionality of passenger seat belts in a convenience sample of 231 Beijing taxis were examined in the months prior to the 2008 Beijing Olympic Games. Driver and front passenger seat belt use was mandated in China from 2004 to help address the growing public health crisis of road trauma. Results from observations made by in-vehicle passengers revealed that 21.2% of drivers were correctly wearing a belt, approximately half were not, and one third were using the belt in a non-functional way. Over 3/4 of this sample of taxi drivers were unrestrained while working. The percentage of functionally available belts was higher for front than rear passengers (88.3% and 22.9%, respectively). This low rate of belt availability in rear seats calls into question the preparedness of the fleet to cater for the safety needs of foreign visitors to China, particularly those from countries with high levels of restraint use. Factors influencing the use/misuse of seat belts in China remain largely unexplored. Results of this pilot study support further investigations of barriers to using injury prevention mechanisms such as seat belts in less motorised countries.

Seat Belt Use Intention among Brazilian Undergraduate Students

OpenAIRE

TORQUATO, RENATA; FRANCO, CLÁUDIO M. A; BIANCHI, ALESSANDRA

2012-01-01

The objectives of this study were to explore self-reported seat belt use and group differences in different scenarios in a Brazilian sample and research the variables related to it. 120 college students answered a questionnaire with variables from the theory of planned behavior in order to evaluate the intention of seat belt use among car occupants. Results indicated that attitude and intention were the variables that most contributed to explaining seat belt use. Intention was highly correlat...

A joint econometric analysis of seat belt use and crash-related injury severity.

Science.gov (United States)

Eluru, Naveen; Bhat, Chandra R

2007-09-01

This paper formulates a comprehensive econometric structure that recognizes two important issues in crash-related injury severity analysis. First, the impact of a factor on injury severity may be moderated by various observed and unobserved variables specific to an individual or to a crash. Second, seat belt use is likely to be endogenous to injury severity. That is, it is possible that intrinsically unsafe drivers do not wear seat belts and are the ones likely to be involved in high injury severity crashes because of their unsafe driving habits. The preceding issues are considered in the current research effort through the development of a comprehensive model of seat belt use and injury severity that takes the form of a joint correlated random coefficients binary-ordered response system. To our knowledge, this is the first instance of such a model formulation and application not only in the safety analysis literature, but in the econometrics literature in general. The empirical analysis is based on the 2003 General Estimates System (GES) data base. Several types of variables are considered to explain seat belt use and injury severity levels, including driver characteristics, vehicle characteristics, roadway design attributes, environmental factors, and crash characteristics. The results, in addition to confirming the effects of various explanatory variables, also highlight the importance of (a) considering the moderating effects of unobserved individual/crash-related factors on the determinants of injury severity and (b) seat belt use endogeneity. From a policy standpoint, the results suggest that seat belt non-users, when apprehended in the act, should perhaps be subjected to both a fine (to increase the chances that they wear seat belts) as well as mandatory enrollment in a defensive driving course (to attempt to change their aggressive driving behaviors).

MACRO MODEL OF SEAT BELT USE BY CAR DRIVERS AND PASSENGERS

Directory of Open Access Journals (Sweden)

Kazimierz JAMROZ

2013-12-01

Full Text Available The article presents some problems of seat belt use by car drivers and passengers. It looks in particular at seat belt use and effectiveness in selected countries. Next, factors of seat belt use are presented and methodology of model development. A macro model of seat belt use is presented based on data from around fifty countries from different continents.

Effectiveness of Ford's belt reminder system in increasing seat belt use

OpenAIRE

Williams, A; Wells, J; Farmer, C

2002-01-01

Objectives: The study investigated the effectiveness in increasing seat belt use of Ford's belt reminder system, a supplementary system that provides intermittent flashing lights and chimes for five minutes if drivers are not belted.

SEAT BELT USE AMONG CAR USERS IN MALAYSIA

Directory of Open Access Journals (Sweden)

S. KULANTHAYAN

2004-01-01

Full Text Available The car is the second (40% most common mode of transportation in Malaysia. In terms of fatal road accidents, car drivers constitute about 9.0% and passengers 13.6% of fatalities. The major cause of car occupants' fatality in such accidents is head injuries, which consist of more than half (56.4% of the fatalities. Thus restraining the head and body, the initial position is the most important injury control strategy for car users. The use of seat belts was deemed one of the most effective ways to reduce road accident fatalities in Malaysia and consequently the mandatory seat belt law was enforced in the early seventies. Therefore, a study on factors influencing the compliance behaviour of seat belt use among cars is needed as to date no such research has been undertaken in Malaysia. A questionnaire study was carried out in Selangor, Malaysia on the compliance behaviour of car occupants in relation to seat belt use. A total of 237 respondents were interviewed and the data analysed using logistic regression method. Six variables were found to be significant at 5 percent level (p<0.05: seating position, location of travel, education level, speeding, night-time driving and enforcement. Compliance with the seat belt law was higher among drivers, educated car users, in the presence of enforcement activities, travelling in city-center areas and car users with a positive attitude towards the risks of speeding and night driving.

Aortic ruptures in seat belt wearers.

Science.gov (United States)

Arajärvi, E; Santavirta, S; Tolonen, J

1989-09-01

Several investigations have indicated that rupture of the thoracic aorta is one of the leading causes of immediate death in victims of road traffic accidents. In Finland in 1983, 92% of front-seat passengers were seat belt wearers on highways and 82% in build-up areas. The mechanisms of rupture of the aorta have been intensively investigated, but the relationship between seat belt wearing and injury mechanisms leading to aortic rupture is still largely unknown. This study comprises 4169 fatally injured victims investigated by the Boards of Traffic Accident Investigation of Insurance Companies during the period 1972 to 1985. Chest injuries were recorded as the main cause of death in 1121 (26.9%) victims, 207 (5.0%) of those victims having worn a seat belt. Aortic ruptures were found at autopsy in 98 victims and the exact information of the location of the aortic tears was available in 68. For a control group, we analyzed 72 randomly chosen unbelted victims who had a fatal aortic rupture in similar accidents. The location of the aortic rupture in unbelted victims was more often in the ascending aorta, especially in drivers, whereas in seat belt wearers the distal descending aorta was statistically more often ruptured, especially in right-front passengers (p less than 0.05). The steering wheel predominated statistically as the part of the car estimated to have caused the injury in unbelted victims (37/72), and some interior part of the car was the most common cause of fatal thoracic impacts in seat belt wearers (48/68) (p less than 0.001). The mechanism of rupture of the aorta in the classic site just distal to the subclavian artery seems to be rapid deceleration, although complex body movements are also responsible in side impact collisions. The main mechanism leading to rupture of the ascending aorta seems to be severe blow to the bony thorax. This also often causes associated thoracic injuries, such as heart rupture and sternal fracture. Injuries in the ascending

Child seat belt guidelines: Examining the 4 feet 9 inches rule as the standard.

Science.gov (United States)

Morse, Amber M; Aitken, Mary E; Mullins, Samantha H; Miller, Beverly K; Pomtree, Mindy M; Ulloa, Erin M; Montgomery, Jeffrey S; Saylors, Marie E

2017-11-01

Current American Academy of Pediatrics recommendations regarding transition from child safety/booster seat to adult safety belt use indicate that children should be at least 4 feet 9 inches, 8 years old, or 80 pounds. Proper fit in the vehicle seat, assessed with a five-point fit test, should also be met. Although most children reach 4 feet 9 inches around age 8 years, each child and vehicle presents a unique combination; thus a child may not fit appropriately in all vehicle types using only the 4 feet 9 inches requirement. We enrolled children, aged 7 years to 12 years, into our study. Height, weight, and demographic data were obtained. A Child Passenger Safety Technician then performed the five-point fit test in each of a uniform lineup of five vehicles. Data were collected on fit in the standard vehicle seat and also in a booster seat. We set 90% as the threshold proportion of children who meet all criteria for proper fit to validate current recommendations of a height of 4 feet 9 inches. Data were collected on 388 children. The percentage of 90% proper fit was met in the compact car and small sport-utility vehicle (SUV). However, only 80 (77%) of 104 students (p guidelines for an adult seat belt do not meet safety requirements for fit, especially in larger, commonly used vehicles (large SUVs and trucks). This emphasizes the need for evaluation of fit by a trained personnel and/or development of standard back seat dimensions in all vehicles for maximum safety. Epidemiologic level 1.

The use of seat belts and contributing factors : an international comparison.

NARCIS (Netherlands)

Mäkinen, T. Wittink, R.D. & Hagenzieker, M.P.

1991-01-01

The purpose of this study was to define factors that contribute to the use or non-use of seat belts. Legislation prescribing compulsory seat belt usage is one of the most important factors. Promotion of the use of seat belts without this legislation is very difficult and time-consuming. So far, the

The effects of seat belt legislation on road traffic injuries.

Science.gov (United States)

Trinca, G W; Dooley, B J

1977-04-01

The compulsory wearing of seat belts, first introduced in the world in Victoria in 1970, has effectively reduced the number of deaths and injuries by approximately one-third for car occupants involved in motor vehicle crashes. Initially, the legislation did not apply to children under the age of eight years, but in 1975 a further law was introduced banning children from the front seat of any vehicle unless properly harnessed. Seat belts offer the best protection for front seat drivers and passengers involved in frontal impacts, but offer less protection to the recipient of a side impact. Ten per cent of car occupants admitted to hospital after a frontal impact show injuries, mostly minor, directly attibutable to the wearing of seat belts.

The 2007 click it or ticket high-visibility seat belt mobilization : traffic tech.

Science.gov (United States)

2010-09-01

In May 2007 the National Highway Traffic Safety Administration : sponsored the fifth national Click It or Ticket (CIOT) : high-visibility seat belt enforcement mobilization, which followed : the CIOT program model of earned and paid media : publicizi...

Race, belief in destiny, and seat belt usage: a pilot study.

Science.gov (United States)

Colón, I

1992-01-01

A survey of 1063 individuals found that when belief in destiny was statistically controlled, differences in seat belt use by race disappeared. Thus, racial differences in seat belt use are statistically accounted for and might be explained by belief in destiny. Efforts to increase seat belt use should target minority groups rather than include them in broadbrush programs. Further, these efforts should take into account this important difference in motivation. PMID:1585969

Increasing seat belt use through state-level demonstration projects : a compendium of initial findings

Science.gov (United States)

2008-08-01

This report summarizes the efforts and results from four of six State-level demonstration projects supported with cooperative agreements from the National Highway Traffic Safety Administration. The projects were intended to increase seat belt use sta...

The Role of Seat Belt in the Prevention of Fatalities and ...

African Journals Online (AJOL)

Background Road traffic crashes still remain a prominent cause of death worldwide but proper use of safety belts can prevent death in some of these accidents. The aim of this study was therefore to examine the role of seat beltuse I violation in Rivers State, Nigeria and to determine its relationship with fatality of road traffic ...

Seat belt, DWI, and other traffic violations among recent immigrants in Florida and Tennessee.

Science.gov (United States)

2013-05-01

Phase I of this project identified two States, Florida and Tennessee, that maintain information on drivers traffic violations and residency status. : Phase II analyzed State databases to examine seat belt nonuse, DWI, and other traffic safety viol...

49 CFR 571.209 - Standard No. 209; Seat belt assemblies.

Science.gov (United States)

2010-10-01

... seat belt assembly to fit the user, including such hardware that may be integral with a buckle... the proper use of the assembly, stressing particularly the importance of wearing the assembly snugly... of Standard No. 208. (a)(1) A manual seat belt assembly, which is subject to the requirements of S5.1...

Car Seat Safety

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Car Seat Safety KidsHealth / For Parents / Car Seat Safety ... certified child passenger safety technician.) Guidelines for Choosing Car Seats Choose a seat with a label that ...

[Use of seat belts and mobile phone while driving in Florence: trend from 2005 to 2009].

Science.gov (United States)

Lorini, Chiara; Pellegrino, Elettra; Mannocci, Federico; Allodi, Guendalina; Indiani, Laura; Mersi, Anna; Petrioli, Giuseppe; Santini, Maria Grazia; Garofalo, Giorgio; Bonaccorsi, Guglielmo

2012-01-01

to evaluate the trend over time of the use of seat belts by drivers and passengers of cars and vans and the use of hand held mobile phone while driving in Florence from 2005 to 2009. DESIGN, SETTING AND PARTICIPANTS AND MAIN OUTCOME MEASURES: direct observations (58,773 vehicles) have been conducted to detect the use of seat belts by occupants of cars and vans, and the use of mobile phone while driving. It has been carried out correlation analysis between the use of the seat belt by occupants of vehicles and between the simultaneous use of this device and mobile phone while driving.Moreover, it has been carried out time series analysis (ARIMA Box Jenkins) of in the prevalence of the use of seat belts by occupants of vehicles observed, of mobile phone by drivers and the trend of the risk to drive using the mobile phone with unfastened seat belt rather than to drive using the mobile phone with fastened seat belt. seat belts were used on average by 75.7% of drivers, 75.5% of front passengers and 25.1% of rear passengers. The average mobile phone use while driving was 4.5%. Drivers most frequently fasten seat belt if front passengers use it and while they do not use mobile phone. The use of seat belts by drivers and front passengers has not changed over time, whereas the use of mobile phone while driving has significantly increased. The prevalence of using mobile phone with unfastened seat belt rather than to use it with fastened seat belt while driving has significantly decreased over the years, indicating an increase in the use of mobile phone, especially among those who fasten the seat belt. it is necessary to plan and realize stronger interventions in the whole area.

Seat belt use to save face: impact on drivers' body region and nature of injury in motor vehicle crashes.

Science.gov (United States)

Han, Guang-Ming; Newmyer, Ashley; Qu, Ming

2015-01-01

Seat belt use is the single most effective way to save lives and reduce injuries in motor vehicle crashes. However, some case reports described seat belt use as a double-edged sword because some injuries are related to seat belt use in motor vehicle crashes. To comprehensively understand the effects of seat belt use, we systemically investigated the association between seat belt use and injuries based on anatomic body region and type of injury in drivers involved in motor vehicle crashes. The injury information was obtained by linking crash reports with hospital discharge data and categorized by using the diagnosis codes based on the Barell injury diagnosis matrix. A total of 10,479 drivers (≥15 years) in passenger vehicles involved in motor vehicle crashes from 2006 to 2011 were included in this study. Seat belt use significantly reduced the proportions of traumatic brain injury (10.4% non-seat belt; 4.1% seat belt) and other head, face, and neck injury (29.3% non-seat belt; 16.6% seat belt) but increased the proportion of spine: thoracic to coccyx injury (17.9% non-seat belt; 35.5% seat belt). Although the proportion of spine: thoracic to coccyx injury was increased in drivers with seat belt use, the severity of injury was decreased, such as fracture (4.2% with seat belt use; 22.0% without seat belt use). Furthermore, the total medical charges decreased due to the change of injury profiles in drivers with seat belt use from a higher percentage of fractures (average cost for per case $26,352) to a higher percentage of sprains and/or strains ($1,897) with spine: thoracic to coccyx injury. This study provide a comprehensive picture for understanding the protective effect of seat belt use on injuries based on anatomic body region and type of injury in drivers involved in motor vehicle crashes.

Using naturalistic driving data to identify variables associated with infrequent, occasional, and consistent seat belt use.

Science.gov (United States)

Reagan, Ian J; McClafferty, Julie A; Berlin, Sharon P; Hankey, Jonathan M

2013-01-01

Seat belt use is one of the most effective countermeasures to reduce traffic fatalities and injuries. The success of efforts to increase use is measured by road side observations and self-report questionnaires. These methods have shortcomings, with the former requiring a binary point estimate and the latter being subjective. The 100-car naturalistic driving study presented a unique opportunity to study seat belt use in that seat belt status was known for every trip each driver made during a 12-month period. Drivers were grouped into infrequent, occasional, or consistent seat belt users based on the frequency of belt use. Analyses were then completed to assess if these groups differed on several measures including personality, demographics, self-reported driving style variables as well as measures from the 100-car study instrumentation suite (average trip speed, trips per day). In addition, detailed analyses of the occasional belt user group were completed to identify factors that were predictive of occasional belt users wearing their belts. The analyses indicated that consistent seat belt users took fewer trips per day, and that increased average trip speed was associated with increased belt use among occasional belt users. The results of this project may help focus messaging efforts to convert occasional and inconsistent seat belt users to consistent users. Copyright © 2012 Elsevier Ltd. All rights reserved.

Pattern of seat belt use and its associated factors among taxi drivers ...

African Journals Online (AJOL)

Objective: Road traffic injuries constitute a major public health concern that demands effective interventions. Use of car seat belts is recommended as an effective intervention to reduce serious and fatal road traffic injuries. The study intended to investigate the pattern of seat belt use and its correlates among taxi drivers in ...

76 FR 53660 - Federal Motor Vehicle Safety Standards; Seat Belt Assemblies

Science.gov (United States)

2011-08-29

... Traffic Safety Administration 49 CFR Part 571 [Docket No. NHTSA-2011-0078] Federal Motor Vehicle Safety... integration of electrical signals from vehicle crash sensors would work with the requested mechanical seat... (350,000) of the vehicles were stopped in the traffic lane prior to the crash event (pg. 22, Table 7...

Beating the Odds. An Educational Program Relating Safety Belt Use to Health Lifestyles for High School Students.

Science.gov (United States)

Department of Transportation, Washington, DC. National Highway Safety Bureau.

This program module is designed to encourage the use of safety measures in driving, emphasizing the use of seat belts. The learning activities focus upon: (1) the importance of the use of safety belts as the most effective preventive measure in a safe and healthy lifestyle; (2) the reasons people cite for not wearing safety belts and the accuracy…

75 FR 66686 - Federal Motor Vehicle Safety Standards; Seat Belt Assembly Anchorages, School Bus Passenger...

Science.gov (United States)

2010-10-29

... loose belts) also applies to seats that have wheelchair positions or side emergency doors behind them... have wheelchair positions or side emergency doors behind them); and, the test requirements for self... which correspond to the size of some high school football players) and school buses closer in weight to...

The benefit of seat belt legislation in the United Kingdom.

Science.gov (United States)

McCarthy, M

1989-09-01

Legislation for compulsory wearing of seat belts by car drivers and front seat passengers has been acclaimed as a major public health advance. Reports from other countries, and two recent evaluative studies in the United Kingdom, have suggested that legislation reduces both deaths and injuries. To assess the effect of the UK law 5 years after its implementation, trends in routine data for 1976-1987 have been reviewed. There were two sources of data: mortality statistics, published by the Office of Population Censuses and Surveys in the quarterly Monitor DH4, and road accident statistics, recorded by the police and published by the Department of Transport. There is a downward trend in deaths over the period, but the data show little impact from the law. One explanation for this lack of effect is the risk compensation hypothesis, which suggests that "safety" improvements are transferred by drivers into increased performance--the amount and speed of travel. Public health policies need to take into account the complex behavioural interactions between travel and safety choices if they are to affect underlying trends.

Attitudes towards child restrains and seat belts usage in the learned population of Karachi, Pakistan.

Science.gov (United States)

Siddiqui, Emaduddin; Ejaz, Kiran; Waheed, Shahan; Kazi, Ghazala Irfan; Khursheed, Munawar

2014-01-01

Motor vehicles crashes (MVCs) are the leading cause of injury related morbidity and mortality in developed countries. Recent evidence proves that properly used child seat belts can dramatically reduce the risk of severe and life-threatening injury from MVCs. There are rarities of thought and inspiration regarding the use of child seat belts in our society and region, therefore we lack of data regarding factors and paucity of usage of child seat belts in motor vehicles. This study aimed to assess the knowledge and attitudes of child seat belt usage among the educated population in Karachi, Pakistan. Altogether 304 employees were investigated. They were employees of Aga Khan University who were using their cars and having children younger than 10 years old. A cross sectional observational study was designed, and a 36-item questionnaire in English was used to collect data on participants' demographic details, designation, educational level, economic status, validity of driving license, number of children and cars, availability of adult seat belts and child seat belts along with their functionality, awareness, knowledge and attitude toward its use, and reason of not using these devices. SPSS version 20 for Windows was used to analyze the data and the Chi-square test was used. Totally 290 participants were recruited with a response rate of 72% (212). Of 212 participants, 126 (59%) were male. 154 (72.6%) participants had valid driver licenses, and 154 (72.6%) had adult seat belts in their vehicles. Only 32 (15%) reported regular use of adult seat belts. Although 168 (79.2%) participants had some knowledge about child restrains (CRs), only 65 (22%) had CRs in their cars. Eighty-two (38.7%) participants got the knowledge about CRs and seat belts from media. Mothers were more concerned about the use of CRs than fathers. Only 14 (6.6%) parents were found to use both adult and child seat belts all the time. Of the 157 parents who did not us use CRs, 42 considered unnecessary

Child seat belt guidelines: Examining the 4 feet 9 inches rule as the standard.

Science.gov (United States)

Morse, Amber M; Aitken, Mary E; Mullins, Samantha H; Miller, Beverly K; Pomtree, Mindy M; Ulloa, Erin M; Montgomery, Jeffrey S; Saylors, Marie E

2017-08-01

Current American Academy of Pediatrics recommendations regarding transition from child safety/booster seat to adult safety belt use indicate that children should be at least 4 feet 9 inches, 8 years old, or 80 pounds. Proper fit in the vehicle seat, assessed with a five-point fit test, should also be met. Although most children reach 4 feet 9 inches around age 8 years, each child and vehicle presents a unique combination; thus a child may not fit appropriately in all vehicle types using only the 4 feet 9 inches requirement. We enrolled children, aged 7 years to 12 years, into our study. Height, weight, and demographic data were obtained. A Child Passenger Safety Technician then performed the five-point fit test in each of a uniform lineup of five vehicles. Data were collected on fit in the standard vehicle seat and also in a booster seat. We set 90% as the threshold proportion of children who meet all criteria for proper fit to validate current recommendations of a height of 4 feet 9 inches. Data were collected on 388 children. The percentage of 90% proper fit was met in the compact car and small sport-utility vehicle (SUV). However, only 80 (77%) of 104 students (p vehicles (large SUVs and trucks). This emphasizes the need for evaluation of fit by a trained personnel and/or development of standard back seat dimensions in all vehicles for maximum safety. Epidemiologic study, level III; Therapeutic study, level V.

A cost benefit analysis of an enhanced seat belt enforcement program in South Africa.

Science.gov (United States)

Harris, G T; Olukoga, I A

2005-04-01

To examine whether a program to increase the wearing of seat belts in a South African urban area would be worthwhile in societal terms. A cost benefit analysis of a one year enhanced seat belt enforcement program in eThekwini (Durban) Municipality. Data were drawn from two main sources--a 1998 study of the cost of road crashes in South Africa and, given the absence of other data, a meta-analysis of the effectiveness of various types of interventions to reduce road crash casualties in the United States--and were analyzed using cost benefit analysis. A program designed to enforce greater wearing of seat belts, estimated to cost 2 million rand in one year, could be reasonably expected to increase seat belt usage rates by 16 percentage points and reduce fatalities and injuries by 9.5%. This would result in saved social costs of 13.6 million rand in the following year or a net present value of 11.6 million rand. There would also be favorable consequences for municipal finances. Investment in a program to increase seat belt wearing rates is highly profitable in societal terms.

[Roadside observation on the use of safety belt in Guangzhou and Nanning cites of China].

Science.gov (United States)

Li, Li-ping; Stevenson, Mark; Ivers, Rebecca; Zhou, Ying

2006-08-01

To determine the rates of correct use of safety belt (CUSB) among drivers and front seat passengers in Guangzhou and Nanning through roadside observation and to provide scientific evidence for the development of intervention plan and to strengthen road safety law enforcement. Observational sites were randomly selected from three road types (Highway, Main Street and Subordinate Street). Targeted automobiles were observed at each site at four different times and uniformed checklists were used to record safety belt use during observations. Within each vehicle, belt use by drivers of different sex, road type, workday/weekend, day/night and seating position were calculated. Data was analyzed, using Chi-square tests to compare the statistic significance. (1)The rate of CUSB and non-use rate among drivers were higher in Nanning than in Guangzhou (P= 0.00) but the rate of incorrect use was on the contrarary. (2) The rate of CUSB by front seat passengers in Guangzhou was higher than that in Nanning (P = 0.04); as well as the rate of (P = 0.00) incorrect use while the non-use rate was on the contrarary. (3)In general, the rate of CUSB was higher on highways than on local streets (P = 0.00). (4) The CUSB rate of drivers and front seat passengers was higher at daytime than at night (P = 0.00), and the rate of incorrect use was higher at working days than weekends (P = 0.00). (5) The CUSB rate was higher for female drivers than for males in Guangzhou (P = 0.00), but there no statistical significance was found in Nanning (P = 0.21). Results suggested that intervention actions should be undertaken to raise the awareness of the importance of safety belt use. Effective public information and education programs, law enforcement and mandatory safety belt use, prioritizing programs on people neglegent to the importance are necessary to increase the safety belt use and to decrease the mortality and injuries caused by traffic accidents.

Head injury causation scenarios for belted, rear-seated children in frontal impacts.

Science.gov (United States)

Bohman, Katarina; Arbogast, Kristy B; Bostrom, Ola

2011-02-01

Head injuries are the most common serious injuries sustained by children in motor vehicle crashes and are of critical importance with regard to long-term disability. There is a lack of understanding of how seat belt-restrained children sustain head injuries in frontal impacts. The aim of the study was to identify the AIS2+ head injury causation scenarios for rear-seated, belt-restrained children in frontal impacts, including the set of parameters contributing to the injury. In-depth crash investigations from two National Highway Traffic Safety Administration (NHTSA) databases, the National Automotive Sampling System-Crashworthiness Data System (NASS-CDS; 1997-2008) and the Crash Injury Research and Engineering Network (CIREN; 1996-2009), were collected and analyzed in detail. Selection criteria were all frontal impacts with principal direction of force (PDOF) of 11, 12, and 1 o'clock involving rear-seated, three-point belt-restrained, with or without booster cushion, children from 3 to 13 years with an AIS2+ head injury. Cases were analyzed using the BioTab method of injury causation assessment in order to systematically analyze the injury causation scenario for each case. There were 27 cases meeting the inclusion criteria, 19 cases with MAIS2 head injuries and 8 cases with MAIS3+ head injuries, including 2 fatalities. Three major injury causation scenarios were identified, including head contact with seatback (10 cases), head contact with side interior (7 cases,) and no evidence of head contact (9 cases). Head injuries with seatback or side interior contact typically included a PDOF greater than 10 degree (similar to the Insurance Institute for Highway Safety [IIHS] and EuroNCAP offset frontal testing) and vehicle maneuvers. For seatback contact, the vehicle's movements contributed to occupant kinematics inboard the vehicle, causing a less than optimal restraint of the torso and/or torso roll out of the shoulder belt. For side interior contact, the PDOF and

Demonstration of the Trauma Nurses Talk Tough seat belt diversion program in North Carolina.

Science.gov (United States)

2014-03-01

Trauma Nurses Talk Tough is a seat belt diversion program originally developed at the Legacy Emanuel Hospital in Portland, Oregon, in 1988. Attendance at the course is a condition for a one-time dismissal of a seat belt citation without fine or court...

Percentage of Drivers and Front Seat Passengers Wearing Seat Belts, 2012 & 2014, All States

Data.gov (United States)

U.S. Department of Health & Human Services — Source for 2012 national data: National Occupant Protection Use Survey (NOPUS), 2012. Source for 2012 state data: State Observational Survey of Seat Belt Use, 2012....

Safety belt and mobile phone usage in vehicles in Barcelona (Spain

Directory of Open Access Journals (Sweden)

Jose M Martínez-Sánchez

2014-07-01

Conclusion: Our study shows noticeably high prevalence of people not wearing safety belt in the rear seats. Moreover, four out of one hundred drivers still use the mobile phone while driving during a moment of the trip.

A social media program to increase adolescent seat belt use.

Science.gov (United States)

Drake, Stacy A; Zhang, Ni; Applewhite, Courtney; Fowler, Katherine; Holcomb, John B

2017-09-01

In response to motor vehicle crashes remaining the leading cause of death for teenagers in the United States, a nursing clinical group (n = 10) in conjunction with a local hospital injury prevention program created an educational campaign to bolster seat belt use. The nursing students created an Instagram account to serve as an educational tool to promote seat belt use among teenagers aged 14-19, and the program was presented at three high school health fairs. In all, 135 postings were made to the account over a 3-month period. The number of likes posted by high school students was the unit of analysis. The most significant result (p = .01) was the difference between postings most liked (celebrities wearing seat belts) and least liked (postings made at the high school health fair), otherwise, differences among postings liked (humor postings, response requests, pictures of celebrities, factual data) were not significant. Instagram user engagement, measured in number of likes, is indicative that social media provides platforms to promote injury prevention efforts. Further research is needed to identify measurable elements of social media and to follow-up on behavioral changes following participation. © 2017 Wiley Periodicals, Inc.

Determining the Relationship of Primary Seat Belt Laws to Minority Ticketing

Science.gov (United States)

2011-09-01

Racial profiling is often raised as an issue when States change their seat belt law from secondary enforcement (i.e., stop only for some other violation) to primary enforcement (i.e., stop for an observed belt law violation alone). Thirteen States ma...

Explaining state-to-state differences in seat belt use : an analysis of socio-demographic variables.

Science.gov (United States)

2011-02-01

"Despite the extensive evidence about the benefits of seat belt use, there is a great deal of variation in use within the US. For example, the national average for seat belt use in 2009 was 84 percent while the state-level averages ranged from 68 per...

Using in-depth investigations to identify transportation safety issues for wheelchair-seated occupants of motor vehicles.

Science.gov (United States)

Schneider, Lawrence W; Klinich, Kathleen D; Moore, Jamie L; MacWilliams, Joel B

2010-04-01

In-depth investigations of motor-vehicle crashes involve detailed inspection, measurement, and photodocumentation of vehicle exterior and interior damage, evidence of belt-restraint use, and evidence of occupant contacts with the vehicle interior. Results of in-depth investigations thereby provide the most objective way to identify current and emerging injury problems and issues in occupant safety and crash protection, and provide important feedback on the real-world performance of the latest restraint-system and vehicle crashworthiness technologies. To provide an objective understanding of real-world transportation safety issues for wheelchair-seated travelers, the University of Michigan Transportation Research Institute (UMTRI) has been conducting and assembling data from in-depth investigations of motor-vehicle crashes and non-crash adverse moving-vehicle incidents, such as emergency vehicle braking, turning, and swerving, in which there was at least one vehicle occupant sitting in a wheelchair. The results of 39 investigations involving 42 wheelchair-seated occupants have been assembled and entered into a wheelchair-occupant crash/injury database. In addition, a biomechanical analysis of each case has been performed to identify key safety issues for wheelchair-seated travelers. The wheelchairs of 34 of the 42 occupants who were seated in wheelchairs while traveling in motor vehicles were effectively secured by either a four-point, strap-type tiedown system or a docking securement device, and all but one of these properly secured wheelchairs remained in place during the crash or non-collision event. However, 30 of the 42 occupants were improperly restrained, either because of non-use or incomplete use of available belt restraints, or because the belt restraints were improperly positioned on the occupant's body. Twenty-six of the 42 occupants sustained significant injuries and 10 of these occupants died as a direct result of injuries sustained, or from

Rural and Urban Differences in Passenger-Vehicle-Occupant Deaths and Seat Belt Use Among Adults - United States, 2014.

Science.gov (United States)

Beck, Laurie F; Downs, Jonathan; Stevens, Mark R; Sauber-Schatz, Erin K

2017-09-22

Motor-vehicle crashes are a leading cause of death in the United States. Compared with urban residents, rural residents are at an increased risk for death from crashes and are less likely to wear seat belts. These differences have not been well described by levels of rurality. 2014. Data from the Fatality Analysis Reporting System (FARS) and the Behavioral Risk Factor Surveillance System (BRFSS) were used to identify passenger-vehicle-occupant deaths from motor-vehicle crashes and estimate the prevalence of seat belt use. FARS, a census of U.S. motor-vehicle crashes involving one or more deaths, was used to identify passenger-vehicle-occupant deaths among adults aged ≥18 years. Passenger-vehicle occupants were defined as persons driving or riding in passenger cars, light trucks, vans, or sport utility vehicles. Death rates per 100,000 population, age-adjusted to the 2000 U.S. standard population and the proportion of occupants who were unrestrained at the time of the fatal crash, were calculated. BRFSS, an annual, state-based, random-digit-dialed telephone survey of the noninstitutionalized U.S. civilian population aged ≥18 years, was used to estimate prevalence of seat belt use. FARS and BRFSS data were analyzed by a six-level rural-urban designation, based on the U.S. Department of Agriculture 2013 rural-urban continuum codes, and stratified by census region and type of state seat belt enforcement law (primary or secondary). Within each census region, age-adjusted passenger-vehicle-occupant death rates per 100,000 population increased with increasing rurality, from the most urban to the most rural counties: South, 6.8 to 29.2; Midwest, 5.3 to 25.8; West, 3.9 to 40.0; and Northeast, 3.5 to 10.8. (For the Northeast, data for the most rural counties were not reported because of suppression criteria; comparison is for the most urban to the second-most rural counties.) Similarly, the proportion of occupants who were unrestrained at the time of the fatal crash

A comparison of safety belt use between commercial and noncommercial light-vehicle occupants.

Science.gov (United States)

Eby, David W; Fordyce, Tiffani A; Vivoda, Jonathon M

2002-05-01

The purpose of this study was to conduct an observational survey of safety belt use to determine the use rate of commercial versus noncommercial light-vehicle occupants. Observations were conducted on front-outboard vehicle occupants in eligible commercial and noncommercial vehicles in Michigan (i.e.. passenger cars, vans/minivans, sport-utility vehicles, and pickup trucks). Commercial vehicles that did not fit into one of the four vehicle type categories, such as tractor-trailers, buses, or heavy trucks, were not included in the survey. The study found that the restraint use rate for commercial light-vehicle occupants was 55.8% statewide. The statewide safety belt use rate for commercial light-vehicles was significantly lower than the rate of 71.2% for noncommercial light-vehicles. The safety belt use rate for commercial vehicles was also significantly different as a function of region, vehicle type, seating position, age group, and road type. The results provide important preliminary data about safety belt use in commercial versus noncommercial light-vehicles and indicate that further effort is needed to promote safety belt use in the commercial light-vehicle occupant population. The study also suggests that additional research is required in order to develop effective programs that address low safety belt use in the commercial light-vehicle occupant population.

Knowledge, attitude and use of seat belt among commercial drivers ...

African Journals Online (AJOL)

The effectiveness of seat belt usage in reducing the severity of the sequelae of road traffic accidents is widely known. ... Each correct response to the knowledge questions was scored one mark and wrong response or non-response was ...

A comparative policy analysis of seat belt laws : final report.

Science.gov (United States)

2014-06-24

This analysis examined data from a variety of sources to estimate the benefit of enhancing Iowas current law to require all : passengers to use seat belts. In addition to assessing Iowans opinions about changing the law, a literature review, a ...

Demonstration of the trauma nurses talk tough seat belt diversion program in North Carolina reaches high-risk drivers : traffic tech.

Science.gov (United States)

2014-03-01

Nationally, more than 8 of every 10 drivers wear seat belts, but : individual State belt rates vary from as high as 98% to as low as : 69%. Within individual States, rural areas often have lower rates. : Strong seat belt laws and highly visible enfor...

Influence of an Enforcement Campaign on Seat-Belt and Helmet Wearing, Karachi-Hala Highway, Pakistan

Science.gov (United States)

Bhatti, Junaid A.; Ejaz, Kiran; Razzak, Junaid A.; Tunio, Israr Ali; Sodhar, Irshad

2011-01-01

This study assessed to what extent an enforcement campaign influenced seat-belt and helmet wearing on a Pakistani highway. The study setting was the Karachi-Hala highway where a traffic enforcement campaign was conducted from Dec 2009 to Feb 2010. Seat-belt and helmet wearing were observed in Nov 2009 and Apr 2010 at Karachi toll plaza. Differences in wearing rates as a function of occupants’ age, sex, and vehicle type were compared between the two periods. On average, 9 119 (Standard deviation=1 896) traffic citations were issued per month from Aug 2009 to Feb 2010; 4.2% of which were for not wearing helmet. A 22.5% increase in citations was observed for Dec 2009 to Feb 2010 periods compared with Aug 2009 to Oct 2009 periods. Nearly six thousand four-wheeled and four hundred two-wheeled motorized vehicle occupants were observed in Nov 2009 and Apr 2010. Overall, two of the five drivers and one of the five front seat occupants wore seat belts. This proportion was significantly higher in drivers and front-seat occupants of cars than those of heavier vehicles. Similarly, one of two motorcyclists used a helmet but this proportion was 5.8% for pillion riders in Nov 2009. The increased enforcement had a limited influence on belt wearing in drivers (+4.0%; 95% Confidence Interval [95%CI]=1.8–6.1) and occupants (+6.2%; 95%CI=4.2–8.2). A higher increase was observed for motorcyclists (+9.8%; 95%CI=2.6–16.8) and pillion riders (+12.8%; 95%CI=5.4, 20.5). These results suggested that serious efforts are required to increase seat-belt and helmet use on Pakistani highways. Improving enforcement resources, increased fines, not allowing such vehicles on roads, and awareness campaigns targeting drivers of heavy vehicles might increase wearing rates in Pakistan. PMID:22105384

Active Prompting to Decrease Cell Phone Use and Increase Seat Belt Use While Driving

OpenAIRE

Clayton, Michael; Helms, Bridgett; Simpson, Cathy

2006-01-01

Automobile crashes are the leading cause of death for those aged 3 to 33, with 43,005 (118 per day) Americans killed in 2002 alone. Seat belt use reduces the risk of serious injury in an accident, and refraining from using a cell phone while driving reduces the risk of an accident. Cell phone use while driving increases accident rates, and leads to 2,600 U.S. fatalities each year. An active prompting procedure was employed to increase seat belt use and decrease cell phone use among drivers ex...

Impact of Implementing a Primary Enforcement Seat Belt Law in Florida : A Case Study

Science.gov (United States)

2012-08-01

On June 30, 2009, Florida implemented a primary seat belt law. The State was already engaged in a Rural : Demonstration Program (RDP) to increase belt usage in rural areas in the northern part of the State and participated : regularly in annual Click...

Seat belt and mobile phone use among vehicle drivers in the city of Doha, Qatar: an observational study.

Science.gov (United States)

Mahfoud, Ziyad R; Cheema, Sohaila; Alrouh, Hekmat; Al-Thani, Mohammed Hamad; Al-Thani, Al Anoud Mohammed; Mamtani, Ravinder

2015-09-22

In Qatar traffic injuries and fatalities are of serious concern. Mobile phone use whilst driving has been associated with increased risk of vehicular collisions and injuries. Seat belt use has been demonstrated to save lives and reduce the severity of road traffic injuries. Whereas previously published studies may have looked at all front passengers, this study aims to obtain reliable estimates of the prevalence of seat belt and mobile phone use among vehicle drivers in the city of Doha, Qatar. Additionally, we aim to investigate the association of these behaviors with other variables namely gender, time of the day and type of vehicle. An observational study on 2,011 vehicles was conducted in 2013. Data were collected at ten sites within Doha city over a two-week period. Two trained observers surveyed each car and recorded observations on a data collection form adapted from a form used in a 2012 Oklahoma observational study. Associations were assessed using the Chi-squared test or Fisher's exact test. A p-value of .05 or less was considered statistically significant. Overall, 1,463 (72.7 %) drivers were found using a seat belt (95 % CI: 70.8-74.7 %) and 150 (7.5 %) their mobile phones (95 % CI: 6.3-8.6 %) during the observation period. Mobile phone use was significantly associated with not using a seat belt and driving a sport utility vehicle. Significantly lower rates of seat belt use were observed in the early morning and late afternoon. No gender differences were observed. Seatbelt use in Doha was found to be similar to countries in the region but lower than those in western countries. Also, studies from other high-income locations, reported lower rates of mobile phone use while driving than in Doha. Despite road traffic crashes being one of the leading causes of death in Qatar, three out of 10 drivers in Doha, Qatar, do not use a seat belt and about one in 12 use a mobile phone while driving. More efforts, in the form of awareness campaigns and increased law

Car seat inspection among children older than 3 years: Using data to drive practice in child passenger safety.

Science.gov (United States)

Kroeker, Amber M; Teddy, Amy J; Macy, Michelle L

2015-09-01

Motor vehicle crashes are the leading cause of unintentional death and disability among children 4 years to 12 years of age in the United States. Despite the high risk of injury from motor vehicle crashes in this age group, parental awareness and child passenger safety programs in particular may lack focus on this age group. This is a retrospective cross-sectional analysis of child passenger safety seat checklist forms from two Safe Kids coalitions in Michigan (2013) to identify restraint type upon arrival to car seat inspections. Other variables were included if the coalition provided a new child safety seat and if the child had a sibling who underwent a car seat inspection. χ statistics were used to compare change in restraint use on arrival and at departure, the proportion of children attending a car seat inspection event by age, the age category of children by site, the proportion of children with siblings also undergoing a car seat inspection by age, and the distribution of a new child safety seat by age. Data were available from 1,316 Safe Kids Huron Valley and 3,215 Safe Kids Greater Grand Rapids car seat inspections. Just 10.8% of the total seats inspected were booster seats. Child safety seats for infant and young children were more commonly inspected (rear-facing carrier [40.3%], rear-facing convertible [10.2%], and forward-facing [19.3%] car seats). Few children at inspections used a seat belt only (5.4%) or had no restraint (13.8%). Children 4 years and older were found to be in a suboptimal restraint at least 30% of the time. Low proportions of parents use car seat inspections for children in the booster seat age group. The proportion of children departing the inspection in a more protective restraint increased with increasing age. This highlights an area of weakness in child passenger safety programs and signals an opportunity to strengthen efforts on The Booster Age Child. Epidemiologic/prognostic study, level III.

Using haptic feedback to increase seat belt use of service vehicle drivers.

Science.gov (United States)

2011-01-01

This study pilot-tested a new application of a technology-based intervention to increase seat belt use. The technology was based on a : contingency in which unbelted drivers experienced sustained haptic feedback to the gas pedal when they exceeded 25...

The Role of Seat Belt in the Prevention of Fatalities and ...

African Journals Online (AJOL)

TNHJOURNALPH

The study was a retrospective study conducted in ... The Role of Seat Belt in Determining Road Traffic Accident Outcomes - Akinbami B.O.. Lagos State is .... The highest number of injured was in 1982 and the lowest in 1977. (figure 1). Table J: Demopaphla ot rcNUJ. accicleau in riven ~.Nigeria from liiOOI5 toJ01J ill Mia sa.

Development of an Emergency Locking Unit for a Belt-In-Seat (BIS System Using a MEMS Acceleration Sensor

Directory of Open Access Journals (Sweden)

Chang Hyun Baek

2010-04-01

Full Text Available This paper proposes an emergency locking unit (ELU for a seat belt retractor which is mounted on the back frame of a vehicle seat. The proposed unit uses a recliner sensor based on a MEMS acceleration sensor and solenoid mechanism. The seat has an upper frame supported to tilt on a lower frame. The retractor in belt in seat (BIS system is supported by the upper frame. The proposed recliner sensor based on a MEMS acceleration sensor comprises orientation means for maintaining a predetermined orientation of emergency relative to the lower frame independently of the force of gravity when the upper frame tilts on the lower frame. Experimental results show that the developed recliner sensor unit operates effectively with respect to rollover angles. Thus, the developed unit will have a considerable potential to offer a new design concept in BIS system.

14 CFR 27.1413 - Safety belts.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Safety belts. 27.1413 Section 27.1413 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Equipment Safety Equipment § 27.1413 Safety belts. Each safety belt...

Expanding the seat belt program strategies toolbox: a starter kit for trying new program ideas.

Science.gov (United States)

2016-10-01

The purpose of this research was to explore alternative strategies for increasing seat belt use. Researchers examined behavior : change strategies proven effective in education, healthcare, advertising, and marketing, and they considered how these : ...

Estimated medical cost savings in Massachusetts by implementation of a primary seat belt law

Science.gov (United States)

2008-12-01

This report examines 2006 hospital discharge data reporting cases where the external cause of injury to a vehicle occupant was a motor vehicle crash to predict the estimated savings to Massachusetts if a primary seat belt law is implemented. The savi...

Does obesity affect the position of seat belt loading in occupants involved in real-world motor vehicle collisions?

Science.gov (United States)

Hartka, Thomas R; Carr, Hannah M; Smith, Brittany R; Melmer, Monica; Sochor, Mark R

2018-02-28

Previous work has shown that the lap belt moves superior and forward compared to the bony pelvis as body mass index (BMI) increases. The goal of this project was to determine whether the location of lap belt loading is related to BMI for occupants who sustained real-world motor vehicle collisions (MVCs). A national MVC database was queried for vehicle occupants over a 10-year period (2003-2012) who were at least 16 years old, restrained by a 3-point seat belt, sitting in the front row, and involved in a front-end collision with a change in velocity of at least 56 km/h. Cases were excluded if there was not an available computed tomography (CT) scan of the abdomen. CT scans were then analyzed using adipose enhancement of 3-dimensional reconstructions. Scans were assessed for the presence a radiographic seat belt sign (rSBS), or subcutaneous fat stranding due to seat belt loading. In scans in which the rSBS was present, anterior and superior displacement of rSBS from the anterior-superior iliac spine (ASIS) was measured bilaterally. This displacement was correlated with BMI and injury severity. The inclusion and exclusion criteria yielded 151 cases for analysis. An rSBS could definitively be identified in 55 cases. Cases in which occupants were older and had higher BMI were more likely to display an rSBS. There was a correlation between increasing BMI and anterior rSBS displacement (P obesity may worsen horizontal position but not the vertical position of the lap belt loading during real-world frontal MVCs.

Estimated medical cost savings in Utah by implementation of a primary seat belt law

Science.gov (United States)

2010-05-01

This report examines 2007 hospital discharge data reporting cases where the external cause of injury to : a vehicle occupant was a motor vehicle crash to predict the estimated savings to Utah if a primary seat : belt law is implemented. The savings a...

Estimated medical cost savings in Nevada by implementation of a primary seat belt law

Science.gov (United States)

2008-09-01

This report examines 2007 hospital discharge data reporting cases where the external cause of injury to a vehicle occupant was a motor vehicle crash to predict the estimated savings to Nevada if a primary seat belt law is implemented. The savings are...

Estimated medical cost savings in Vermont by implementation of a primary seat belt law

Science.gov (United States)

2008-09-01

This report examines 2005 hospital discharge data reporting cases where the external cause of injury to a vehicle occupant was a motor vehicle crash to predict the estimated savings to the State of Vermont if a primary seat belt law is implemented. T...

14 CFR 31.63 - Safety belts.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Safety belts. 31.63 Section 31.63 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: MANNED FREE BALLOONS Design Construction § 31.63 Safety belts. (a) There must be a safety belt...

46 CFR 169.723 - Safety belts.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Safety belts. 169.723 Section 169.723 Shipping COAST... Control, Miscellaneous Systems, and Equipment § 169.723 Safety belts. Each vessel must carry a harness type safety belt conforming to Offshore Racing Council (ORC) standards for each person on watch or...

Evaluation of the May 2005 Click It or Ticket mobilization to increase seat belt use

Science.gov (United States)

2007-05-01

Click It or Ticket (CIOT) is an intense, short-duration, seat belt publicity and enforcement program. The CIOT May 2005 Mobilization involved approximately $33 million of purchased media. Law enforcement agencies across the Nation reported issuing mo...

Car safety seat usage and selection among families attending University Hospital Limerick

LENUS (Irish Health Repository)

Scully, P

2016-05-01

The safest way for children to travel within a car is by provision of a weight-appropriate safety-seat. To investigate this, we conducted a cross-sectional study of adult parents who had children under 12 years, and collected information related to: car use, safety-seat legislation, and type of safety-seat employed. Data were reviewed on 120 children from 60 respondents. Ninety-eight (81.7%) children were transported daily by car. Forty-eight (81.4%) respondents were aware that current safety-seat legislation is based on the weight of the child. One hundred and seven (89.9%) children were restrained during travel using a car safety-seat. One hundred and two (96.2%) safety seats were newly purchased, installed in 82.3% (88) cases by family members with installation instructions fully read in 58 (55.2%) cases. Ninety-nine (83.2%) children were restrained using an appropriate safety-seat for their weight. The results show that four out of five families are employing the most appropriate safety-seat for their child, so providing an effective mechanism to reduce car-related injury. However, the majority of safety-seats are installed by family members, which may have child safety consequences.

Estimated medical cost savings in Rhode Island by implementation of a primary seat belt law

Science.gov (United States)

2008-09-01

This report examines 2006 hospital discharge data reporting cases where the external cause of injury to a vehicle occupant was a motor vehicle crash to predict the estimated savings to Rhode Island if a primary seat belt law is implemented. The savin...

SEAT BELT USE INTENTION AMONG BRAZILIAN UNDERGRADUATE STUDENTS/ INTENCIÓN DE USO DEL CINTURÓN DE SEGURIDAD EN ESTUDIANTES UNIVERSITARIOS BRASILEÑOS/ INTENÇÃO DE USO DO CINTO DE SEGURANÇA EM ESTUDANTES UNIVERSITÁRIOS BRASILEIROS

Directory of Open Access Journals (Sweden)

Alessandra Bianchi

2012-12-01

Full Text Available The objectives of this study were to explore selfreported seat belt use and group differences in different scenarios in a Brazilian sample and research the variables related to it. 120 college students answered a questionnaire with variables from the theory of planned behavior in order to evaluate the intention of seat belt use among car occupants. Results indicated that attitude and intention were the variables that most contributed to explaining seat belt use. Intention was highly correlated with seat belt use, and attitude was correlated with intention. Seat belt use was more frequent among drivers and taxi passengers, but not among front and rear seat passengers. The article discusses the implications of the findings for possible interventions to encourage the use of seat belts among drivers and passengers.

Beslissingsprocessen van verkeersdeelnemers : covernota bij de rapporten van W.H. Janssen: "Risk compensation and the effect of an incentive : a laboratory study" (IFZ 1988 C-26), "An experimental evaluation of safety incentive schemes" (IZF 1989 C-19), en "Seat belt wearing and driving behaviour : an empirical investigation" (IZF 1991 C-15).

NARCIS (Netherlands)

Levelt, P.B.M.

1993-01-01

This cover note comments on the following three TNO Institute for Perception (IZF) Reports: (1) "Risk compensation and the effect of an incentive: a laboratory study"; (2) "An experimental evaluation of safety incentive schemes"; and (3) "Seat belt wearing and driving behaviour: an empirical

Evaluation of a rural demonstration program to increase seat belt use in the Great Lakes Region.

Science.gov (United States)

2009-03-01

Six States in the Great Lakes Region (Region 5) participated in a Rural Demonstration Program to increase seat belt : use in rural areas and among high-risk occupants, such as young males and occupants of pickup trucks. These : efforts, which include...

36 CFR 1004.15 - Safety belts.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Safety belts. 1004.15 Section 1004.15 Parks, Forests, and Public Property PRESIDIO TRUST VEHICLES AND TRAFFIC SAFETY § 1004.15 Safety... administered by the Presidio Trust will have the safety belt or child restraint system properly fastened at all...

Factors associated with rear seating of children in motor vehicles: a study in two low-income, predominantly Hispanic communities.

Science.gov (United States)

Greenberg-Seth, Jennifer; Hemenway, David; Gallagher, Susan S; Lissy, Karen S; Ross, Julie B

2004-07-01

This study examined child seating patterns in two predominantly low-income, Hispanic communities in Massachusetts. The purpose was to determine the factors associated with child rear seating in the community as a whole and for a subset of Hispanic motorists. Five hundred and five vehicles carrying child passengers and no adult other than the driver were observed in parking lots of fast food restaurants and grocery stores. Four hundred and thirty-two vehicle drivers agreed to be interviewed. A child was defined as a passenger younger than age 12 as determined by appearance and height (head below the vehicle headrest when seated). Variables under study included driver gender, age, ethnicity, and educational attainment; driver shoulder belt use; driver perception of passenger-side airbag presence; and the number and ages of children in the car. Overall, 51% of vehicles were observed with all children seated in the rear. In a bivariate analysis, child rear seating was strongly associated with female drivers ( P = 0.01), younger drivers ( P = 0.02) driver shoulder belt use ( P safety behavior (e.g. seat belt use). Messages should be culturally appropriate and should emphasize driver seat belt use in conjunction with rear seating and the importance of rear seating regardless of the presence of a passenger-side airbag.

Synaptic ribbon. Conveyor belt or safety belt?

Science.gov (United States)

Parsons, T D; Sterling, P

2003-02-06

The synaptic ribbon in neurons that release transmitter via graded potentials has been considered as a conveyor belt that actively moves vesicles toward their release sites. But evidence has accumulated to the contrary, and it now seems plausible that the ribbon serves instead as a safety belt to tether vesicles stably in mutual contact and thus facilitate multivesicular release by compound exocytosis.

Active Prompting to Decrease Cell Phone Use and Increase Seat Belt Use while Driving

Science.gov (United States)

Clayton, Michael; Helms, Bridgett; Simpson, Cathy

2006-01-01

Automobile crashes are the leading cause of death for those aged 3 to 33, with 43,005 (118 per day) Americans killed in 2002 alone. Seat belt use reduces the risk of serious injury in an accident, and refraining from using a cell phone while driving reduces the risk of an accident. Cell phone use while driving increases accident rates, and leads…

Seat belt syndrome with unstable Chance fracture dislocation of the second lumbar vertebra without neurological deficits.

Science.gov (United States)

Onu, David O; Hunn, Andrew W; Bohmer, Robert D

2014-01-08

The seat belt syndrome is a recognised complication of seat belt use in vehicles. Unstable Chance fractures of the spine without neurological deficits have been reported infrequently. We describe a young woman with completely disrupted Chance fracture of the second lumbar vertebra in association with left hemidiaphragmatic rupture/hernia, multiple bowel perforations, splenic capsular tear, left humeral shaft and multiple rib fractures. These injuries which resulted from high-speed vehicle collision and led to death of one of the occupants were readily detected by trauma series imaging. The patient was successfully treated by a dedicated multidisciplinary team which adopted a staged surgical approach and prioritisation of care. There were no manifested neurological or other deficits after 1 year of follow-up. To the authors' knowledge, this is the first report of such a case in Australasia. We discuss the challenging surgical management, highlighting the role of radiological imaging in such cases and provide a literature review.

The effects of video-based and activity-based instruction on high school students' knowledge, attitudes, and behavioral intentions related to seat belt use

Science.gov (United States)

Jones, Tudor Griffith, III

The purpose of this study was to determine the effect of video-based science instruction and accompanying activity-based instruction on the knowledge, attitudes, and behavioral intentions of high school students' use of seat belts. Secondarily, the purpose was to determine order effects and interactions between the two treatments used in the study: video-based instruction and hands-on activity-based instruction. The study used Ajzen and Fishbein's theory of reasoned action to investigate the factors influencing high school students' behavioral intentions regarding seat belt use. This study used a pretest-posttest-posttest treatment design. Data were collected on 194 students in high school introductory biology and chemistry classes in Gainesville, Florida. Ten intact high school science classes (eight treatment and two control) took pretests and posttests measuring physics knowledge, attitudes, and behavioral intentions toward seat belt use prior to and after participating in the two treatments. The treatment group students participated in at least 500 minutes of instructional time divided among five lessons over 10 instructional days. All participants were pretested on physics knowledge, attitudes, and behavioral intentions toward seat belt use prior to two treatments. Treatment A was defined as participating in one 50-minute video-based instructional lesson. Treatment B was defined as participating in four hands-on science activities regarding crash-related physics concepts. Cronbach's coefficient alpha was used for analysis of the researcher-designed instruments, and ANOVA was used to analyze the data. The results of the analyses (p young adults.

Seat-belt wearing and driving behavior: an instrumented-vehicle study.

Science.gov (United States)

Janssen, W

1994-04-01

Less-than-expected fatality reductions after seat-belt legislation has been introduced in a jurisdiction may be explained in terms of selective recruitment of parts of the driving population and/or behavioral adaptation by beginning belt users. The present investigation has compared the relative merits of these two hypotheses at the level of individual driver behavior. In the initial study the driving behavior of groups of habitual wearers and nonwearers of the belt was compared. Nonwearers made two trips, one with the belt on and one without the belt. Habitual wearers drove belted only. The main part of the experiment was a 105 km freeway route. Two additional tasks of a somewhat more critical nature, a double lane-change manoeuvre and the performance of a braking manoeuvre in front of a fixed obstacle, were performed after the freeway trips. Factor analysis on 39 variables describing driving behavior on the road and during the additional tasks resulted in five factors. One of these, the factor describing the distribution of driving speed on the freeway, differentiated between nonwearers and wearers (thus yielding support for the selective recruitment hypothesis) as well as between wearing and not wearing the belt by the same drivers (thus yielding support for the behavioral adaptation hypothesis). In the follow-up study the original wearers and nonwearers were assigned to one of four experimental treatments: (i) the promise by the experimenter of a considerable incentive for not having a culpable motor vehicle accident over a period of a year. Half the habitual wearer subjects were assigned to this condition. The expectation was that this group would become more careful in their driving; (ii) a control group, consisting of the remaining habitual wearers; (iii) the agreement between the experimenter and the subject that the latter would buckle up in everyday driving for the year to come--half the habitual nonwearer subjects were assigned to this condition; (iv) a

Evaluation of the League General Insurance Company child safety seat distribution program

Science.gov (United States)

1982-05-01

This report presents an evaluation of the child safety seat distribution initiated by the League General Insurance Company in June 1979. The program provides child safety seats as a benefit under the company's auto insurance policies to policy-holder...

Does unbelted safety requirement affect protection for belted occupants?

Science.gov (United States)

Hu, Jingwen; Klinich, Kathleen D; Manary, Miriam A; Flannagan, Carol A C; Narayanaswamy, Prabha; Reed, Matthew P; Andreen, Margaret; Neal, Mark; Lin, Chin-Hsu

2017-05-29

Federal regulations in the United States require vehicles to meet occupant performance requirements with unbelted test dummies. Removing the test requirements with unbelted occupants might encourage the deployment of seat belt interlocks and allow restraint optimization to focus on belted occupants. The objective of this study is to compare the performance of restraint systems optimized for belted-only occupants with those optimized for both belted and unbelted occupants using computer simulations and field crash data analyses. In this study, 2 validated finite element (FE) vehicle/occupant models (a midsize sedan and a midsize SUV) were selected. Restraint design optimizations under standardized crash conditions (U.S.-NCAP and FMVSS 208) with and without unbelted requirements were conducted using Hybrid III (HIII) small female and midsize male anthropomorphic test devices (ATDs) in both vehicles on both driver and right front passenger positions. A total of 10 to 12 design parameters were varied in each optimization using a combination of response surface method (RSM) and genetic algorithm. To evaluate the field performance of restraints optimized with and without unbelted requirements, 55 frontal crash conditions covering a greater variety of crash types than those in the standardized crashes were selected. A total of 1,760 FE simulations were conducted for the field performance evaluation. Frontal crashes in the NASS-CDS database from 2002 to 2012 were used to develop injury risk curves and to provide the baseline performance of current restraint system and estimate the injury risk change by removing the unbelted requirement. Unbelted requirements do not affect the optimal seat belt and airbag design parameters in 3 out of 4 vehicle/occupant position conditions, except for the SUV passenger side. Overall, compared to the optimal designs with unbelted requirements, optimal designs without unbelted requirements generated the same or lower total injury risks for

The influence of age, seat belt, time of day, and type of vehicles on road accidents in Kerman, Iran.

Science.gov (United States)

Mohammadi, Ghorbanali

2009-04-01

Traffic accidents are one of the main external causes of morbidity and mortality in various parts of the world, including Kerman, a city that has experienced rapid growth in the number of cars in the last 5 years. The objective of this article was to identify the influence of age, belt use, time of day, and type of vehicle road accidents of southeastern Iran. This study used data obtained from Kerman police force reports on incidents of road traffic accidents (RTAs). We analyzed the police reports of total road accidents that occurred from 2005 to 2007. The involvement in fatal and non-fatal accidents was determined for females than among males. The analysis of the data indicated that the female drivers have a much better road safety record than male drivers, especially with regards to their involvement in severe traffic accidents. Forty-nine percent of accidents involve passenger cars, which is higher than other type of vehicles. Female drivers were found to be generally safer drivers than their male counterparts; male drivers who did not use seat belts had a higher involvement rate in road traffic accidents. Time of day analyses suggested that the problems of accidents in darkness are not a matter of visibility but a consequence of the way drivers use the roads at night. A number of recommended measures for the improvement of road safety in southeastern Iran are suggested.

Prevalence of seat belt and mobile phone use and road accident injuries amongst college students in Kerman, Iran

Directory of Open Access Journals (Sweden)

Mohammadi Ghorbanali

2011-06-01

Full Text Available 【Abstract】 Objective: To investigate the prevalence of mobile phone and seat belt use in driving in college stu- dents aged 18-24 years. Methods: The study consisted of two phases. In the first phase, a questionnaire was given to 265 college students. The sample contained 188 males and 77 females. In the second phase, the data pertaining to road accident injuries from March 20, 2007 to March 20, 2008 were collected from Bahonar Central Hospital in Kerman, Iran, and analyzed. Results: There were 14.0% of male and 19.0% of fe- male participants traveled belted while driving on urban roads. It indicated that the participants unbelted or using mobile phone were more involved in accidents in last three years. This study also revealed that 19.0% of male and 4.2% of female drivers considered using mobile phone in driving not hazardous. The highest injury and property damage crash rates were 87 and 137 per 100 000 inhabitants, which occured in male group aged 18-24 years. And 30% of all fatalities were 19-24 years old. Conclusions: More than 50% of college students trav- eled unbelted. The females were less involved in road acci- dent injuries. The college students aged 18-24 years had the highest percentages of trauma and head injury. Key words: Craniocerebral trauma; Accidents, traffic; Seat belts; Cellular phone

Burden of road traffic injuries related to delays in implementing safety belt laws in low- and lower-middle-income countries.

Science.gov (United States)

Martin, Aurélie; Lagarde, Emmanuel; Salmi, L Rachid

2018-02-28

Delayed implementation of effective road safety policies must be considered when quantifying the avoidable part of the fatal and nonfatal injuries burden. We sought to assess the avoidable part of disability-adjusted life years (DALYs) lost due to road traffic injuries related to delays in implementing road safety laws in low- and lower-middle-income countries. We chose one country for each of the regions of the World Health Organization (WHO) and World Bank (WB) country income levels. We used freely available data sets (WHO, International Traffic Safety Data and Analysis Group, the WB). Delays in implementation were calculated until 2013, from the year mandatory use of safety belts by motor vehicle front seat occupants was first introduced worldwide. We used life expectancy tables and age groups as social values in the DALY calculation model. From the estimated total burden, avoidable DALYs were calculated using estimates of the effectiveness of seat belt laws on fatal and nonfatal injuries combined, as extracted from published international reviews of evidence. From the reference year 1972, implementation delays varied from 27 years (Uzbekistan) to 41 years in Bolivia (no seat belt law as of 2013). During delays, total absolute numbers of DALYs lost due to road traffic injuries reached 8,462,099 in Nigeria, 7,203,570 in Morocco, 4,695,500 in Uzbekistan, 3,866,391 in Cambodia, 3,253,359 in Bolivia, and 3,128,721 in Sri Lanka. Using effectiveness estimates ranging from 3 to 20% reduction, the avoidable burden of road traffic injuries for car occupants was highest in Uzbekistan (avoidable part from 1.2 to 10.4%) and in Morocco (avoidable part from 1.5 to 12.3%). In countries where users of public transport and pedestrians were the most affected by the burden, the avoidable parts ranged from 0.5 to 4.4% (Nigeria) and from 0.5 to 3.4% (Bolivia). Burden of road traffic injuries mostly affected motorcyclists in Sri Lanka and Cambodia where the avoidable parts were

Countermeasures that work : a highway safety countermeasure guide for state highway safety offices : eighth edition : 2015

Science.gov (United States)

2015-11-01

The guide is a basic reference to assist State Highway Safety Offices in selecting effective, evidence- based : countermeasures for traffic safety problem areas. These areas include: : - Alcohol-and Drug-Impaired Driving; : - Seat Belts and Child Res...

Safety for Your Child: 8 Years

Science.gov (United States)

... Stages Listen Español Text Size Email Print Share Safety for Your Child: 8 Years Page Content Article ... is not buckled by a seat belt. Sports Safety Ask your doctor which sports are right for ...

Seating position, seat belt wearing, and the consequences in facial fractures in car occupants Posição no veículo, uso de cinto de segurança e suas conseqüências nas fraturas de face em ocupantes de carros

Directory of Open Access Journals (Sweden)

Alexandre Siqueira Franco Fonseca

2007-01-01

Full Text Available INTRODUCTION: Trauma caused by traffic accidents is among the main etiologies involved in the occurrence of facial fractures throughout the world. However, the trauma mechanisms involved are different according to the location where the study was performed, due to different conditions of development, legislation, and culture. A retrospective study was done between February 2001 and July 2006, with the purpose of determining the epidemiology and the mechanisms involved in the occurrence of facial fractures among car occupants in the metropolitan area of São Paulo. METHODS: Data were collected from 297 patients admitted with facial fractures to the emergency room of the Hospital das Clínicas, São Paulo University Medical School. Within this period, 151 individuals had been involved in traffic accidents, among which 56 (37.08% were inside passenger cars. These were grouped based on the seating position that they were occupying at the time of the accident and the wearing of seat belts. Data concerning the number and location of fracture lines were obtained from the different groups, and a fracture/patient index (F/P I was calculated to compare and make reference to the impact energy among these groups, for subsequent analysis and discussion. RESULTS: 323 fracture lines occurred among 56 patients who were car occupants. By applying the F/P I, we obtained higher values in the group of rear-seat passengers who were not wearing seat belts (7.23 fractures per patient, followed by the group of drivers not wearing seat belts (6.33 fractures per patient, the group of front-seat passengers not wearing seat belts (5.58 fractures per patient, the group of drivers wearing seat belts (5.54 fractures per patient and, finally, the group of front-seat passengers wearing seat belts (4.00 fractures per patient. None of the rear-seat passengers was wearing seat belts. CONCLUSION: The data collected indicate that the driver position shows a high incidence of facial

Evaluating the impact of child safety seat check-up events on parental knowledge.

Science.gov (United States)

Herring, Ashley B; Jones, Ches; Nunez, Casandra

2002-12-01

Riding unrestrained is the greatest risk factor for death and injury among children in motor vehicles. Restraining a child can reduce the risk of death for that child by up to 71%. However, despite increased awareness, child safety seat usage rates are still disturbingly low. The purpose of this study was to evaluate the impact that child safety seat check-up events have on parental knowledge on child safety seats and installation. The subjects for this study were 101 parents/caregivers who attended child safety seat check-up events in northwest Arkansas from May 2000 through June 2001. A 20-item survey was conducted via the telephone. Results showed that the check-up events in northwest Arkansas have had an impact on self-efficacy. The participants of the events were primarily Caucasian and females in the 30-34 age group. Nine of 10 subjects scored in the high knowledge category. Conclusions are that check-up events do have an impact on parental knowledge and are accepted by the target group. Additionally, participants believed that car seats are of great importance and do protect their children in the event of a crash.

Roll seat belt induced injury of the duodenum.

Science.gov (United States)

Bergqvist, D; Hedelin, H

1976-05-01

A case of duodenal rupture with a roll three-point seatbelt is described. It is apparently the seventh reported case of duodenal rupture in safety belt users. A female driver fell asleep, and her car went off the road, rolling forward in a ditch, slowing slightly, and then came to a sudden stop. The rupture was unusual: on the first part of duodenum, intraperitoneal, and longitudinal. The rupture mechanism is discussed, and the deficiencies of the roll seatbelt pointed out in accidents like the one described.

Fall Protection Characteristics of Safety Belts and Human Impact Tolerance.

Science.gov (United States)

Hino, Yasumichi; Ohdo, Katsutoshi; Takahashi, Hiroki

2014-08-23

Many fatal accidents due to falls from heights have occurred at construction sites not only in Japan but also in other countries. This study aims to determine the fall prevention performance of two types of safety belts: a body belt 1) , which has been used for more than 40 yr in the Japanese construction industry as a general type of safety equipment for fall accident prevention, and a full harness 2, 3) , which has been used in many other countries. To determine human tolerance for impact trauma, this study discusses features of safety belts with reference 4-9) to relevant studies in the medical science, automobile crash safety, and aircrew safety. For this purpose, simple drop tests were carried out in a virtual workplace to measure impact load, head acceleration, and posture in the experiments, the Hybrid-III pedestrian model 10) was used as a human dummy. Hybrid-III is typically employed in official automobile crash tests (New Car Assessment Program: NCAP) and is currently recognized as a model that faithfully reproduces dynamic responses. Experimental results shows that safety performance strongly depends on both the variety of safety belts used and the shock absorbers attached onto lanyards. These findings indicate that fall prevention equipment, such as safety belts, lanyards, and shock absorbers, must be improved to reduce impact injuries to the human head and body during falls.

Lap belt injuries in children.

LENUS (Irish Health Repository)

McGrath, N

2010-07-01

The use of adult seat belts without booster seats in young children may lead to severe abdominal, lumbar or cervical spine and head and neck injuries. We describe four characteristic cases of lap belt injuries presenting to a tertiary children\\'s hospital over the past year in addition to a review of the current literature. These four cases of spinal cord injury, resulting in significant long-term morbidity in the two survivors and death in one child, arose as a result of lap belt injury. These complex injuries are caused by rapid deceleration characteristic of high impact crashes, resulting in sudden flexion of the upper body around the fixed lap belt, and consequent compression of the abdominal viscera between the lap belt and spine. This report highlights the dangers of using lap belts only without shoulder straps. Age-appropriate child restraint in cars will prevent these injuries.

Misuse of car safety seats.

Science.gov (United States)

Bull, M J; Stroup, K B; Gerhart, S

1988-01-01

Correct use of car seats for small children is essential to prevent serious injuries and death from automotive accidents. Failure to use a car seat properly can contribute to serious injury or death of a child. A case study in which misuse of a car seat occurred is reported. The infant died of hemorrhage and shock secondary to liver laceration which resulted from excessive pressure over the abdomen sustained on impact. Surveys of car seat use for small children prior to and following a child restraint law are also reported. Observers noted types of car seats and specific forms of misuse. Survey results suggest that parents are more likely to misuse car seats for infants than toddlers. Medical professionals can reinforce the importance of proper car seat use by incorporating specific car seat use questions into the patient interview and by providing educational materials.

Advanced Infant Car Seat Would Increase Highway Safety

Science.gov (United States)

Dabney, Richard; Elrod, Susan

2004-01-01

An advanced infant car seat has been proposed to increase highway safety by reducing the incidence of crying, fussy behavior, and other child-related distractions that divert an adult driver s attention from driving. In addition to a conventional infant car seat with safety restraints, the proposed advanced infant car seat would include a number of components and subsystems that would function together as a comprehensive infant-care system that would keep its occupant safe, comfortable, and entertained, and would enable the driver to monitor the baby without having to either stop the car or turn around to face the infant during driving. The system would include a vibrator with bulb switch to operate; the switch would double as a squeeze toy that would make its own specific sound. A music subsystem would include loudspeakers built into the seat plus digital and analog circuitry that would utilize plug-in memory modules to synthesize music or a variety of other sounds. The music subsystem would include a built-in sound generator that could synthesize white noise or a human heartbeat to calm the baby to sleep. A second bulb switch could be used to control the music subsystem and would double as a squeeze toy that would make a distinct sound. An anti-noise sound-suppression system would isolate the baby from potentially disturbing ambient external noises. This subsystem would include small microphones, placed near the baby s ears, to detect ambient noise. The outputs of the microphone would be amplified and fed to the loudspeakers at appropriate amplitude and in a phase opposite that of the detected ambient noise, such that the net ambient sound arriving at the baby s ears would be almost completely cancelled. A video-camera subsystem would enable the driver to monitor the baby visually while continuing to face forward. One or more portable miniature video cameras could be embedded in the side of the infant car seat (see figure) or in a flip-down handle. The outputs of

Motivating signage prompts safety belt use among drivers exiting senior communities.

Science.gov (United States)

Cox, B S; Cox, A B; Cox, D J

2000-01-01

Senior drivers are vulnerable to automobile crashes and subsequent injury and death. Safety belts reduce health risks associated with auto crashes. Therefore, it is important to encourage senior drivers to wear safety belts while driving. Using an AB design, replicated five times, we evaluated the short- and long-term effects of a sign with the message "BUCKLE UP, STAY SAFE" attached to a stop sign at the exits of five different senior communities. Safety belt use was stable during two pretreatment assessments averaged across the five sites and 250 drivers (72% and 68% usage), but significantly increased following installation of these signs (94% usage). Six months after installation of the signs, the effect persisted (88% usage). Use of such signs may be a cost-effective way of promoting safety belt use.

Observed use of automatic seat belts in 1987 cars.

Science.gov (United States)

Williams, A F; Wells, J K; Lund, A K; Teed, N

1989-10-01

Usage of the automatic belt systems supplied by six large-volume automobile manufacturers to meet the federal requirements for automatic restraints were observed in suburban Washington, D.C., Chicago, Los Angeles, and Philadelphia. The different belt systems studied were: Ford and Toyota (motorized, nondetachable automatic shoulder belt), Nissan (motorized, detachable shoulder belt), VW and Chrysler (nonmotorized, detachable shoulder belt), and GM (nonmotorized detachable lap and shoulder belt). Use of automatic belts was significantly greater than manual belt use in otherwise comparable late-model cars for all manufacturers except Chrysler; in Chrysler cars, automatic belt use was significantly lower than manual belt use. The automatic shoulder belts provided by Ford, Nissan, Toyota, and VW increased use rates to about 90%. Because use rates were lower in Ford cars with manual belts, their increase was greater. GM cars had the smallest increase in use rates; however, lap belt use was highest in GM cars. The other manufacturers supply knee bolsters to supplement shoulder belt protection; all--except VW--also provide manual lap belts, which were used by about half of those who used the automatic shoulder belt. The results indicate that some manufacturers have been more successful than others in providing automatic belt systems that result in high use that, in turn, will mean fewer deaths and injuries in those cars.

Road safety performance indicators for the interurban road network.

NARCIS (Netherlands)

Yannis, G. Weijermars, W.A.M. Gitelman, V. Vis, M. Chazirisa, A. Papadimitriou, E. & Lima Azevedo, C.

2013-01-01

Various road safety performance indicators (SPIs) have been proposed for different road safety research areas, mainly as regards driver behaviour (e.g. seat belt use, alcohol, drugs, etc.) and vehicles (e.g. passive safety); however, no SPIs for the road network and design have been developed. The

The behavioral impact of an advertising campaign to promote safety belt use.

Science.gov (United States)

Cope, J G; Moy, S S; Grossnickle, W F

1988-01-01

Safety belt use was observed at one restaurant during McDonald's "Make It Click" promotional campaign. Following baseline, the program was monitored without intervention. During the final 2 weeks of the campaign an incentive strategy was added providing a large soft drink contingent on safety belt use. Safety belt use did not change from baseline levels before the incentive phase. The rate of belt use increased under contingent reward and declined during follow-up. The effects of a verbal prompt could not be assessed because of the almost nonexistent use of the "Make It Click" stickers throughout the study.

Study on Fuzzy Comprehensive Evaluation Model for the Safety of Mine Belt Conveyor

Directory of Open Access Journals (Sweden)

Gong Xiaoyan

2017-01-01

Full Text Available To improve the situation of the frequent failures of mine belt conveyor during operation, a model was used to evaluate the safety of mine belt conveyor. Based on the foundation of collecting and analyzing a large quantity of fault information of belt conveyor in the nationwide coal mine, the fault tree model of belt conveyor has been built, then the safety evaluation index system was established by analyzing and removing some secondary indicators. Furthermore, the weighted value of safety evaluation indexs was determined by analytic hierarchy process(AHP, and the single factor fuzzy evaluation matrix was constructed by experts grading method. Additionally, the model was applied in evaluating the security of belt conveyor in Nanliang coal mine. The results shows the security level is recognized to the “general”, which means that this model can be adopted widely in evaluating the safety of mine belt conveyor.

Seat and seatbelt accommodation in fire apparatus: Anthropometric aspects.

Science.gov (United States)

Hsiao, Hongwei; Whitestone, Jennifer; Wilbur, Michael; Lackore, J Roger; Routley, J Gordon

2015-11-01

This study developed anthropometric information on U.S. firefighters to guide fire-apparatus seat and seatbelt designs and future standards development. A stratified sample of 863 male and 88 female firefighters across the U.S. participated in the study. The study results suggested 498 mm in width, 404 mm in depth, and 365-476 mm in height for seat pans; 429-522 mm in width and 542 mm in height for seat back; 871 mm in height for head support; a seat space of 733 mm at shoulder and 678 mm at hip; and a knee/leg clearance of 909 mm in fire truck cab. Also, 1520 mm of lap belt web effective length and 2828 mm of lap-and-shoulder belt web effective length were suggested. These data for fire-truck seats and seatbelts provide a foundation for fire apparatus manufacturers and standards committees to improve firefighter seat designs and seatbelt usage compliance. Published by Elsevier Ltd.

Thoracic aortic injury in motor vehicle crashes: the effect of impact direction, side of body struck, and seat belt use.

Science.gov (United States)

Fitzharris, Michael; Franklyn, Melanie; Frampton, Richard; Yang, King; Morris, Andrew; Fildes, Brian

2004-09-01

Using in-depth, real-world motor vehicle crash data from the United States and the United Kingdom, we aimed to assess the incidence and risk factors associated with thoracic aorta injuries. De-identified National Automotive Sampling System Crashworthiness Data System (U.S.) and Co-operative Crash Injury Study (U.K.) data formed the basis of this retrospective analysis. Logistic regression was used to assess the level of risk of thoracic aorta injury associated with impact direction, seat belt use and, given the asymmetry of the thoracic cavity, whether being struck toward the left side of the body was associated with increased risk in side-impact crashes. A total of 13,436 U.S. and 3,756 U.K. drivers and front seat passengers were analyzed. The incidence of thoracic aorta injury in the U.S. and U.K. samples was 1.5% (n = 197) and 1.9% (n = 70), respectively. The risk was higher for occupants seated on the side closest to the impact than for occupants involved in frontal impact crashes. This was the case irrespective of whether the force was applied toward the left (belted: relative risk [RR], 4.6; 95% confidence interval [CI], 2.9-7.1; p direction. Thoracic aorta injuries were found to be associated with high impact severity, and being struck by a sports utility vehicle relative to a passenger vehicle (RR, 1.7; 95% CI, 1.2-2.3; p = 0.001). Aortic injuries have been conventionally associated with frontal impacts. However, emergency clinicians should be aware that occupants of side-impact crashes are at greater risk, particularly if the occupant was unbelted and involved in a crash of high impact severity.

Evaluation of a five-year Bloomberg Global Road Safety Program in Turkey.

Science.gov (United States)

Gupta, S; Hoe, C; Özkan, T; Lajunen, T J; Vursavas, F; Sener, S; Hyder, A A

2017-03-01

Turkey was included in the Bloomberg Philanthropies funded Global Road Safety Program (2010-14) with Ankara and Afyonkarahisar (Afyon) selected for interventions to manage speed and encourage seat-belt use. The objectives of this study are to present the monitoring and evaluation findings of seat-belt use and speed in Afyon and Ankara over the five years and to assess overall impact of the program on road traffic injury, and death rates in Turkey. Quasi-experimental before after without comparison. In collaboration with the Middle East Technical University, roadside observations and interviews were coupled with secondary data to monitor changes in risk factors and outcomes at the two intervention sites. The percentage of seat-belt use among drivers and front-seat passengers in Afyon and Ankara increased significantly between 2010 and 2014 with increased self-reported use and preceded by an increase in tickets (fines) for not using seat belts. There were uneven improvements in speed reduction. In Afyon, the average speed increased significantly from 46.3 km/h in 2012 to about 52.7 km/h in 2014 on roads where the speed limits were 50 km/h. In Ankara, the average speed remained less than 55 km/h during the program period (range: 50-54 km/h; P < 0.005) for roads where the speed limits were 50 km/h; however, the average speed on roads with speed limits of 70 km/h decreased significantly from 80.6 km/h in 2012 to 68.44 km/h in 2014 (P < 0.005). The program contributed to increase in seat-belt use in Afyon and Ankara and by drawing political attention to the issue can contribute to improvements in road safety. We are optimistic that the visible motivation within Turkey to substantially reduce road traffic injuries will lead to increased program implementation matched with a robust evaluation program, with suitable controls. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Drivers' opinions of enforcement and incentive strategies to promote safety belt use.

NARCIS (Netherlands)

Hagenzieker, M.P.

2017-01-01

During a nationwide campaign to promote safety belt use among military personnel, a field study was conducted at 12 different military bases in the Netherlands. Amount of enforcement, type of publicity, and incentive strategies were varied among military bases. Observations of safety belt use among

AAP Updates Recommendations on Car Seats

Science.gov (United States)

... Size Email Print Share AAP Updates Recommendations on Car Seats Page Content Article Body Children should ride ... of approved car safety seats. Healthy Children Radio: Car Seat Safety Dennis Durbin, MD, FAAP, lead author ...

78 FR 4985 - Uniform Procedures for State Highway Safety Grant Programs

Science.gov (United States)

2013-01-23

...) that were tied to the agency's child restraint performance standards (FMVSS 213). Thus, under today's... consolidates into one rule a number of old regulations (State Highway Safety Agency, Political Subdivision... Belt Performance Grants (formerly codified at 23 U.S.C. 406) and Child Safety and Child Booster Seat...

Enforcement or incentives ? : promoting safety belt use among military personnel in the Netherlands.

NARCIS (Netherlands)

Hagenzieker, M.P.

1991-01-01

During a nationwide campaign to promote safety belt use among military personnel, a field study was conducted at 12 different military bases in the netherlands. Amount of enforcement, type of publicity, and incentive strategies were varied among military bases. Observations of safety belt use among

49 CFR 571.210 - Standard No. 210; Seat belt assembly anchorages.

Science.gov (United States)

2010-10-01

... bolt holes or the centroid of any other means of attachment to the structure specified in 4.1.3.1... are either: (a) For designated seating positions that are common to the same occupant seat and that... common to the same occupant seat, but that face in the same direction, if the vertical centerline of the...

Pediatrician attitudes, knowledge, and practice behavior regarding teen driving safety.

Science.gov (United States)

Campbell, Brendan T; Borrup, Kevin; Corsi, John M; Kelliher, Kristine M; Saleheen, Hassan; Banco, Leonard; Lapidus, Garry

2009-01-01

Each year about 4,000 teens ages 16-19 die on U.S. roads. Injury prevention counseling is recommended as a valuable and cost-effective part of routine health supervision. This study describes pediatrician knowledge and practice regarding teen driving safety. A 31-item self-administered survey was mailed to pediatricians. 160 of 392 pediatricians (41%) completed the survey. During a health supervision visit 93% of pediatricians reported discussing seat belt use, 89% impaired driving, 54% teen licensing laws, and 16% parent teen contract. Half reported having a teen in their practice killed in a crash. A majority surveyed report discussing and counseling teens on first wave teen driver safety issues (seat belts, alcohol use), but most do not discuss graduated driver licensing laws or related issues. Broadly adopted, this inexpensive counseling approach, could lead to reductions in teen motorvehicle crash injuries.

Disparities in safety belt use by sexual orientation identity among US high school students.

Science.gov (United States)

Reisner, Sari L; Van Wagenen, Aimee; Gordon, Allegra; Calzo, Jerel P

2014-02-01

We examined associations between adolescents' safety belt use and sexual orientation identity. We pooled data from the 2005 and 2007 Youth Risk Behavior Surveys (n = 26,468 weighted; mean age = 15.9 years; 35.4% White, 24.7% Black, 23.5% Latino, 16.4% other). We compared lesbian and gay (1.2%), bisexual (3.5%), and unsure (2.6%) youths with heterosexuals (92.7%) on a binary indicator of passenger safety belt use. We stratified weighted multivariable logistic regression models by sex and adjusted for survey wave and sampling design. Overall, 12.6% of high school students reported "rarely" or "never" wearing safety belts. Sexual minority youths had increased odds of reporting nonuse relative to heterosexuals (48% higher for male bisexuals, 85% for lesbians, 46% for female bisexuals, and 51% for female unsure youths; P < .05), after adjustment for demographic (age, race/ethnicity), individual (body mass index, depression, bullying, binge drinking, riding with a drunk driver, academic achievement), and contextual (living in jurisdictions with secondary or primary safety belt laws, percentage below poverty, percentage same-sex households) risk factors. Public health interventions should address sexual orientation identity disparities in safety belt use.

Protection of children restrained in child safety seats in side impact crashes.

Science.gov (United States)

Arbogast, Kristy B; Locey, Caitlin M; Zonfrillo, Mark R; Maltese, Matthew R

2010-10-01

The performance of child restraint systems (CRS) in side impact motor vehicle crashes has been under study due to the injury and fatality burden of these events. Although previous research has quantified injury risk or described injured body regions, safety advances require an understanding of injury causation. Therefore, the objective was to delineate injury causation scenarios for CRS-restrained children in side impacts and document probable contact points in the vehicle interior. Two in-depth crash investigation databases, the Crash Injury Research and Engineering Network and the Partners for Child Passenger Safety Study, were queried for rear-seated, CRS-restrained children in side impact crashes who sustained Abbreviated Injury Scale 2+ injury. These cases were reviewed by a multidisciplinary team of physicians and engineers to describe injury patterns, injury causation, and vehicle components that contributed to the injuries. Forty-one occupants (average age, 2.6 years) met the inclusion criteria. Twenty-four were near side to the crash, 7 were far side, and 10 were center seated. The most common injuries were to the skull and brain with an increasing proportion of skull fracture as age increased. Head and spine injuries without evidence of head contact were rare but present. All thoracic injuries were lung contusions and no rib fractures occurred. Near-side head and face contacts points were along the rear vertical plane of the window and the horizontal plane of the window sill. Head and face contact points for center- and far-side occupants were along the edges of the front seat back and front seat head restraint. Head injuries are the target for injury prevention for children in CRS in side impact crashes. Most of these injuries are due to the contact; for near-side occupants, contact with the CRS structure and the door interior, for far- or center-seated occupants, contact with the front seat back. These data are useful in developing both educational and

Non-Compliance of Malaysia Motor Vehicles (Safety Seatbelts) Rules 1978

OpenAIRE

Sivasankar SAMBASIVAM; Karmegam KARUPPIAH; Shamsul Bahri Mohd Tamrin; Kulanthayan Subramaniam; Hassan Sadeghi Naeini

2015-01-01

Background: Seat belts have been proven as one of the most successful means of preventing or reducing injuries to occupants of cars during an accident. This paper examines the reasons behind the non-compliance of the seat belt law in Malaysia and suggests possible measures to get the percentage of seat belt usage up higher.Methods: Various databases of articles were searched for seat belt usage in Malaysia, related legislation, related accident data, type of injuries and reviewed to put forth...

Rear seat safety: Variation in protection by occupant, crash and vehicle characteristics.

Science.gov (United States)

Durbin, Dennis R; Jermakian, Jessica S; Kallan, Michael J; McCartt, Anne T; Arbogast, Kristy B; Zonfrillo, Mark R; Myers, Rachel K

2015-07-01

Current information on the safety of rear row occupants of all ages is needed to inform further advances in rear seat restraint system design and testing. The objectives of this study were to describe characteristics of occupants in the front and rear rows of model year 2000 and newer vehicles involved in crashes and determine the risk of serious injury for restrained crash-involved rear row occupants and the relative risk of fatal injury for restrained rear row vs. front passenger seat occupants by age group, impact direction, and vehicle model year. Data from the National Automotive Sampling System Crashworthiness Data System (NASS-CDS) and Fatality Analysis Reporting System (FARS) were queried for all crashes during 2007-2012 involving model year 2000 and newer passenger vehicles. Data from NASS-CDS were used to describe characteristics of occupants in the front and rear rows and to determine the risk of serious injury (AIS 3+) for restrained rear row occupants by occupant age, vehicle model year, and impact direction. Using a combined data set containing data on fatalities from FARS and estimates of the total population of occupants in crashes from NASS-CDS, logistic regression modeling was used to compute the relative risk (RR) of death for restrained occupants in the rear vs. front passenger seat by occupant age, impact direction, and vehicle model year. Among all vehicle occupants in tow-away crashes during 2007-2012, 12.3% were in the rear row where the overall risk of serious injury was 1.3%. Among restrained rear row occupants, the risk of serious injury varied by occupant age, with older adults at the highest risk of serious injury (2.9%); by impact direction, with rollover crashes associated with the highest risk (1.5%); and by vehicle model year, with model year 2007 and newer vehicles having the lowest risk of serious injury (0.3%). Relative risk of death was lower for restrained children up to age 8 in the rear compared with passengers in the right

Survival in fatal road crashes: body mass index, gender, and safety belt use.

Science.gov (United States)

Sivak, Michael; Schoettle, Brandon; Rupp, Jonathan

2010-02-01

This study evaluated the associations of body mass index (BMI), gender, and use of safety belts with the survival of drivers involved in fatal road crashes. The census data of all U.S. fatal crashes that did not involve pedestrians, bicyclists, or motorcyclists were examined for an 11-year period. If involved in a crash with one or more fatalities, the odds of female drivers being among the fatalities are 1.28 times higher than those of male drivers, and the odds of unbelted drivers being among the fatalities are 5.43 times higher than those of belted drivers. The relationship of survivability to BMI depends on the gender and safety belt use of the driver. For male drivers, increased BMI appears beneficial when safety belts are used but detrimental when not used. For belted female drivers, normal BMI is associated with the lowest odds of being killed, and both increased and decreased BMIs increase the odds. For unbelted female drivers, no reliable trends were present among the BMI categories.

Factors associated with the enactment of safety belt and motorcycle helmet laws.

Science.gov (United States)

Law, Teik Hua; Noland, Robert B; Evans, Andrew W

2013-07-01

It has been shown that road safety laws, such as motorcycle helmet and safety belt laws, have a significant effect in reducing road fatalities. Although an expanding body of literature has documented the effects of these laws on road safety, it remains unclear which factors influence the likelihood that these laws are enacted. This study attempts to identify the factors that influence the decision to enact safety belt and motorcycle helmet laws. Using panel data from 31 countries between 1963 and 2002, our results reveal that increased democracy, education level, per capita income, political stability, and more equitable income distribution within a country are associated with the enactment of road safety laws. © 2012 Society for Risk Analysis.

Naturalistic driving study of rear seat child occupants: Quantification of head position using a Kinect™ sensor.

Science.gov (United States)

Arbogast, Kristy B; Kim, Jinyong; Loeb, Helen; Kuo, Jonny; Koppel, Sjaan; Bohman, Katarina; Charlton, Judith L

2016-09-01

Restraint performance is evaluated using anthropomorphic test devices (ATDs) positioned in prescribed, optimal seating positions. Anecdotally, humans-children in particular-assume a variety of positions that may affect restraint performance. Naturalistic driving studies (NDSs), where cameras and other data acquisition systems are placed in a vehicle used by participants during their regular transportation, offer means to collect these data. To date, these studies have used conventional video and analysis methods and, thus, analyses have largely been qualitative. This article describes a recently completed NDS of child occupants in which their position was monitored using a Kinect sensor to quantify their head position throughout normal, everyday driving trips. A study vehicle was instrumented with a data acquisition system to measure vehicle dynamics, a set of video cameras, and a Kinect sensor providing 3D motion capture at 1 Hz of the rear seat occupants. Participant families used the vehicle for all driving trips over 2 weeks. The child occupants' head position was manually identified via custom software from each Kinect color image. The 3D head position was then extracted and its distribution summarized by seat position (left, rear, center) and restraint type (forward-facing child restraint system [FFCRS], booster seat, seat belt). Data from 18 families (37 child occupants) resulted in 582 trips (with children) for analysis. The average age of the child occupants was 45.6 months and 51% were male. Twenty-five child occupants were restrained in FFCRS, 9 in booster seats, and 3 in seat belts. As restraint type moved from more to less restraint (FFCRS to booster seat to seat belt), the range of fore-aft head position increased: 218, 244, and 340 mm on average, respectively. This observation was also true for left-right movement for every seat position. In general, those in the center seat position demonstrated a smaller range of head positions. For the first

Comparative Performance of Rear Facing Child Restraint Systems on the CMVSS 213 Bench and Vehicle Seats

Science.gov (United States)

Tylko, Suzanne; Locey, Caitlin M.; Garcia-Espana, J. Felipe; Arbogast, Kristy B.; Maltese, Matthew R.

2013-01-01

The purpose of this study was to compare the dynamic response of rear-facing child restraint systems (RFCRS) installed on the CMVSS 213 sled bench and a selection of vehicle seats. Thirty-six sled tests were conducted: three models of rear facing CRS with an anthropomorphic test device (ATD) representing a 12 month old child (CRABI) were affixed via lower anchors (LATCH), 3 point belt without CRS base, and 3 point belt with CRS base to one of three vehicle seats or the CMVSS 213 bench seat. All CRS were subjected to an identical sled acceleration pulse. Two types of matched pair analysis: “bench-to-vehicle” and “method of attachment” were conducted. Statistically significant differences were observed in the kinematic responses of the ATD and the CRS. This is the first study to quantify differences between the regulatory bench and vehicle seats on a system level and evaluate the influence of attachment method. Our results show that the difference in RFCRS forward excursion between 3-point belt with base and LATCH installations was between 1 and 7 percent on the bench and 22 to 76 percent on the vehicle seats. When evaluating the dynamic performance of RFCRS, the use of real vehicle seats from vehicles that commonly carry children may provide valuable insight. The findings would require further confirmation using a broader selection of RFCRS and vehicle seats, before generalizable conclusions can be drawn. PMID:24406967

The Behavioral Impact of an Advertising Campaign to Promote Safety Belt Use.

Science.gov (United States)

Cope, John G.; And Others

1988-01-01

Safety belt use with and without addition of an incentive strategy was observed among 8,635 drivers at a drive-through restaurant. During the promotional campaign, average rate of belt use tripled compared to baseline following the introduction of a contingent reward (a large soft drink), and declined during followup. (JW)

Interaction of the Zagros Fold-Thrust Belt and the Arabian-type, deep-seated folds in the Abadan Plain and the Dezful Embayment, SW Iran

Energy Technology Data Exchange (ETDEWEB)

Fard, Iraj Abdollahie [National Iranian Oil Co., Exploration Directorate, Tehran (Iran); Braathen, Alvar [Bergen Univ., Centre for Integrated Petroleum Research, Bergen (Norway); Mokhtari, Mohamad [International Institute of Earthquake Engineering and Seismology, Tehran (Iran); Alavi, Seyed Ahmad [Shahid Beheshti Univ., Earth Sciences Faculty, Tehran (Iran)

2006-07-01

The Dezful Embayment and Abadan Plain (SW Iran) contain major parts of the remaining Iranian oil reserves. These oil provinces are characterized by two types of structural closure: very gentle N-S- to NE-SW-trending basement-cored anticlines (Arabian-type highs) in the SE; and open to tight, NW-SE-trending thrust-related folds in the NE (Zagros Fold-Thrust Belt; ZFTB). Most deep-seated anticlines are upright and symmetrical in Cretaceous and older units. In some cases they reveal steep faults in their core which, in the light of regional observations, suggest that the basement is involved in the faulting. Untested plays around these anticlines include reefal build-ups, debris flows, truncated sedimentary sections and onlapping clastic units. The ZFTB shows a classic structural style, with overall shortening reflected in thrust displacement declining from the Dezful Embayment towards the frontal zone in the Abadan Plain. The Early Cambrian Hormuz Salt represents the fundamental sole for the fold-thrust belt and locates major fault-propagation folds in the southwestern Dezful Embayment. These folds represent the main petroleum target of the area. Another important unit is the Mid-Miocene Gachsaran Formation. This detachment reveals both in-sequence and out-of-sequence thrusting. Interaction of deep-seated anticlines and fold-thrust structures results in thrust imbrications and formation of duplexes within the Gachsaran Formation when thrusts abut deep-seated anticlines. Above the crest of the anticlines, thrusts are forced up-section into syn-tectonic deposits, whereas the forelimb reveals out-of-the-syncline thrusts. Several petroleum plays are identified in such zones of structural interaction, including anticlines above buttress-related duplexes, out-of-sequence imbricate thrust fans with associated folds above major anticlines, truncation of footwall layers below potentially sealing thrusts, and sub-thrust anticlines. (Author)

1991 National campaign to increase safety belt usage.

NARCIS (Netherlands)

National Highway Traffic Safety Administration NHTSA

1992-01-01

The central theme of this paper is the national campaign of the USA to be conducted in 1991 and 1992, in order to reach the goal of 70 percent safety belt usage by 1992. Among other things, it is shown that visible enforcement of existing laws offers the greatest potential for achieving this goal.

Securing the safety of our most precious cargo: SAFE KIDS.

Science.gov (United States)

Vick, Judith W

2010-01-01

There are staggering and tragic statistics involving children, car seats, and motor vehicle accidents. According to the Centers for Disease Control and Prevention, motor vehicle injuries are the leading cause of death among children from 0 to 15 years of age, and in the United States during 2005, 1,335 children ages 14 years and younger died as occupants in motor vehicle accidents; approximately 184,000 were injured. That is an average of 4 deaths and 504 injuries each day. National Highway Traffic Safety Administration (NHTSA) statistics show that nearly one-half of deaths and injuries in children occurred because they were not properly restrained. Child safety seats and safety belts, when installed and used properly, can prevent injuries and save lives. Among children under age 5, an estimated 425 lives were saved in 2006 by child restraint use. Research on the effectiveness of child safety seats has found them to reduce fatal injury by 71% for infants, and by 54% for toddlers in passenger cars. This article discusses the need for increased education of parents and healthcare professionals about selection and installation of car safety restraints, and the importance of developing a child safety restraint program.

The effects of enforcement and rewards on safety-belt use : a field study in The Netherlands.

NARCIS (Netherlands)

Hagenzieker, M.P.

1990-01-01

It turns out that young male drivers aged between 18 and 25 use their safety belt less often than other driver groups in The Netherlands. For this reason, it was decided to conduct a nationwide campaign to promote safety belt use by military personnel during October and November 1988. The campaign

The effect of a 3-point harness restraint and car seat in whiplash-type lateral impacts.

Science.gov (United States)

Kumar, Shrawan; Ferrari, Robert; Narayan, Yogesh; Jones, Troy

2006-01-01

Seventeen healthy volunteers were subjected to right and left lateral impacts 5.0, 6.8, 9.2, and 16.8 m/s acceleration while positioned in a Volvo car seat with lap and shoulder seat belt restraint in laboratory setting. The purpose of this study was to determine the effect of using a standard 3-point lap and shoulder seat belt and Volvo car seat on the response of the cervical muscles to increasing low-velocity lateral impacts. A previous study of lateral impacts in a 5-point harness restraint with head and trunk in neutral posture suggests that the burden of impact is borne primarily by the splenius capitis muscle contralateral to the direction of impact. That study, however, used a nonstandard harness for automobiles, and other studies suggest that a lap-and-shoulder seat belt may increase the risk of whiplash injury. Triaxial accelerometers recorded the acceleration of the 1) sled, 2) torso at the shoulder level, and 3) head of the participant, while bilateral electromyograms of the sternocleidomastoids, trapezii, and splenii capitis were also recorded. For participants experiencing a right or left lateral impact, the muscle responses increased with increasing levels of acceleration (P trend to progressively decrease with increasing levels of acceleration. The peak head accelerations relative to the sled ranged from 2.5 to 10.6 m/s. When the impact was a right lateral impact, at the highest sled acceleration, the left splenius capitis generated 47% of its maximal voluntary contraction (MVC), and the left trapezius also 46% of its MVC; the left and right sternocleidomastoid, right splenius capitis, and right trapezius generated 29% or less of their MVC. For the highest level of acceleration in a left lateral impact, the right splenius capitis generated 48% of its MVC and the right trapezius 57% of the MVC, the left and right sternocleidomastoid, left splenius capitis, and left trapezius generated 29% or less of their MVC. In both directions of impact, the

Keeping our children safe in motor vehicles: knowledge, attitudes and practice among parents in Kuwait regarding child car safety.

Science.gov (United States)

Raman, Sudha R; Landry, Michel D; Ottensmeyer, C Andrea; Jacob, Susan; Hamdan, Elham; Bouhaimed, Manal

2013-01-01

Child safety restraints can reduce risk of death and decrease injury severity from road traffic crashes; however, knowledge about restraints and their use in Kuwait is limited. A cross-sectional, self-administered survey about child car safety was used among a convenience sample of parents of children aged 18 years or younger at five Kuwaiti university campuses. Of 552 respondents, over 44% have seated a child in the front seat and 41.5% have seated a child in their lap while driving. Few parents are aware of and fewer report using the appropriate child restraint; e.g., 36% of parents of infants recognised an infant seat and 26% reported using one. Over 70% reported wearing seat belts either "all of the time" (33%) or "most of the time" (41%). This new information about parents' knowledge and practice regarding child car seat use in Kuwait can inform interventions to prevent child occupant injury and death.

Motivating safety belt use at a community hospital: an effective integration of incentive and commitment strategies.

Science.gov (United States)

Nimmer, J G; Geller, E S

1988-06-01

An effective hospital-based safety-belt program incorporated several advantages over prior attempts to increase safety belt use, including (a) the use of indigenous staff as program sponsors, coordinators, and delivery agents; (b) a yearlong program evaluation; and (c) a combination of extrinsic incentives and intrinsic commitment. To be eligible for a weekly $5, employees met the following contingencies: (a) signed a pledge card; (b) displayed the signed pledge card in their vehicle; and (c) wore a safety belt. Overall, belt use increased from a 2-week baseline mean of 15.6% to 34.7% during the 6-month intervention, and decreased to 25.6% at withdrawal. For the pledge card signers (n = 188) and the nonsigners (n = 533), belt use increased from baseline means of 29.4% and 11.8% to intervention use rates of 75.1 and 17.7%, respectively. Withdrawal and 4-month follow-up use rates were 56.0% and 44.9% for the Pledge group, and 17.2% and 22.1% for the Nonpledge group.

Comparison of Thoracic Injury Risk in Frontal Car Crashes for Occupant Restrained without Belt Load Limiters and Those Restrained with 6 kN and 4 kN Belt Load Limiters.

Science.gov (United States)

Foret-Bruno, J Y; Trosseille, X; Page, Y; Huère, J F; Le Coz, J Y; Bendjellal, F; Diboine, A; Phalempin, T; Villeforceix, D; Baudrit, P; Guillemot, H; Coltat, J C

2001-11-01

In France, as in other countries, accident research studies show that a large proportion of restrained occupants who sustain severe or fatal injuries are involved in frontal impacts (65% and 50%, respectively). In severe frontal impacts with restrained occupants and where intrusion is not preponderant, the oldest occupants very often sustain severe thoracic injuries due to the conventional seat belt. As we have been observing over the last years, we will expect in the coming years developments which include more solidly-built cars, as offset crash test procedures are widely used to evaluate the passive safety of production vehicles. The reduction of intrusion for the most severe frontal impacts, through optimization of car deformation, usually translates into an increase in restraint forces and hence thoracic injury risk with a conventional retractor seat belt for a given impact severity. It is, therefore essential to limit the restraint forces exerted by the seat belt on the thorax in order to reduce the number of road casualties. In order to address thoracic injury risk in frontal impact, Renault cars have been equipped with the Programmed Restraint System (PRS) since 1995. The PRS is a restraint system that combines belt load limitation and pyrotechnic belt pretension. In an initial design of the Programmed Restraint System (PRS1), the belt load limiter was a steel component designed to shear at a given shoulder force, namely 6 kN. It was mounted between the retractor and the lower anchorage point of the belt. The design of the PRS was modified in 1998 (PRS2), but the principle of load limitation was maintained. The threshold was decreased to 4 kN and this lower belt belt-force limiter has been combined with a specially designed airbag. This paper reports on 347 real-world frontal accidents where the EES (Equivalent Energy Speed) ranged from 35 to 75 km/h. One hundred and ninety-eight (198) of these accidents involved cars equipped with the 6 kN load limiter

Lightweight, fire-retardant, crashworthy aircraft seat cushioning

Science.gov (United States)

Haslim, Leonard A.; Mcdonough, Paul T.

1991-01-01

A two page discussion of non-aerospace seating applications and the design of NASA's safety seat cushioning (SSC) is presented. The SSC was designed for both safety and comfort in order to replace polyurethane cushioning which is flammable and produces lethal fumes upon combustion. The SSC is composed of advanced fabric reinforced composites and is lightweight, fire-retardent, and crashworthy. The seat design consists of central elliptical tubular spring supports made of fire-resistant and fatigue-durable composites surrounded by a fire-blocking sheath. The cushioning is made crashworthy by incorporating energy-absorbing, viscoelastic layers between the nested, elliptical-hoop springs. The design is intended to provide comfortable seating that meets aircraft-loading requirements without using the conventional polyurethane materials. The designs of an aircraft seat and structural components of the SSC are also presented.

The Status of Road Safety in Iran during 2001 – 2006

Directory of Open Access Journals (Sweden)

M. J. Jafari

2013-08-01

.Result: The results revealed that during the period of 6 years, death toll has been increased by 9 deaths per 100000 person of the population. Moreover, application of seat belt and safety helmet has been increased by 20% and 18%, respectively. It also indicated that the number of motorists and the length of paved roads have been increased by 20%, and 10%, respectively. The net income per capita has also grown from 5884 US$ to 7968 US$ and the life expectancy has gone up from 68.9 years to 70.9 years, the percentage of the literate population has grown by 2% (from 76% to 78% and the human development index has increased from 0.721 to 0.759. The results of the present study showed that the increased level of death toll per 10000 vehicles and the increased level (% of seat belt as well as helmet application, paved roads, urbanization, the net income per capita, life expectancy, literacy and human development index were statistically significant and R2 coefficient for this factors was 0.84, 0.9, 0.994, 0.9, 0.97, 0.82, 0.69 and 0.84 respectively. .Conclusion: According to result of the present study, roads safety were not in an appropriate level. The roads safety status can be determined using road safety indicators to be applied for road safety promotion.

An ecological model to factors associated with booster seat use: A population based study.

Science.gov (United States)

Shimony Kanat, Sarit; Gofin, Rosa

2017-11-01

Belt-positioning booster seat use (BPB) is an effective technology to prevent severe child injury in cases of car crash. However, in many countries, age-appropriate car restraint use for children aged 4-7 years old remains the lowest among all age groups. The aim of this study was to identify the main determinants of BPB use through a comprehensive approach. An ecological model was used to analyze individual, parent-child relationships, and neighborhood characteristics. Parents of children enrolled in the first and second grades completed a self-reported questionnaire (n=745). The data were subjected to multilevel modeling. The first level examined individual and parent-child relationship variables; in addition the second level tested between neighborhood variance. According to parental self- reports, 56.6% of their children had used a BPB on each car trip during the previous month. The results indicated that the determinants positively related to BPB use were individual and parental; namely, the number of children in the family, the parents' car seat belt use, parental knowledge of children's car safety principles, and a highly authoritative parenting style. Children's temperaments and parental supervision were not associated with BPB use. At the neighborhood level, a small difference was found between neighborhoods for BPB users compared to non-users. Copyright © 2017 Elsevier Ltd. All rights reserved.

Social prejudice hindering proper use of car safety seats.

Science.gov (United States)

Kanburoglu, Mehmet Kenan; Cizmeci, Mehmet Nevzat; Akelma, Ahmet Zulfikar; Orun, Emel; Yesilyurt, Kubra; Tatli, Mustafa Mansur

2013-12-01

The compliance of parents with child passenger safety (CPS) has been mainly explained by their level of knowledge. Social, ethnic and cultural factors have not been investigated in detail. This study investigated the rate of compliance of parents with CPS guidelines, as well as the factors hindering it. Parents of infants aged 2-10 days were enrolled. The proportions of families obtaining a car safety seat (CSS; 57%) and complying with CPS recommendations (2%) were very low. Most of the parents thought CSS were harmful for infants (mother, 57%; father, 63%), despite having already purchased one. Parents believed their children to be too small to use CSS and cannot sit in CSS because they should lie flat on their backs at all times. These prejudices may be due to the social and cultural circumstances specific to Turkey, or corresponding findings may be found in countries with similar socioeconomic status. © 2013 The Authors. Pediatrics International © 2013 Japan Pediatric Society.

NASA Standards Inform Comfortable Car Seats

Science.gov (United States)

2014-01-01

NASA developed standards, which included the neutral body posture (NBP), to specify ways to design flight systems that support human health and safety. Nissan Motor Company, with US offices in Franklin, Tennessee, turned to NASA's NBP research for the development of a new driver's seat. The 2013 Altima now features the new seat, and the company plans to incorporate the seats in upcoming vehicles.

The Application of a Piezo-Resistive Cardiorespiratory Sensor System in an Automobile Safety Belt

Science.gov (United States)

Hamdani, Syed Talha Ali; Fernando, Anura

2015-01-01

Respiratory and heart failure are conditions that can occur with little warning and may also be difficult to predict. Therefore continuous monitoring of these bio-signals is advantageous for ensuring human health. The car safety belt is mainly designed to secure the occupants of the vehicle in the event of an accident. In the current research a prototype safety belt is developed, which is used to acquire respiratory and heart signals, under laboratory conditions. The current safety belt is constructed using a copper ink based nonwoven material, which works based on the piezo-resistive effect due to the pressure exerted on the sensor as a result of expansion of the thorax/abdomen area of the body for respiration and due to the principle of ballistocardiography (BCG) in heart signal sensing. In this research, the development of a theoretical model to qualitatively describe the piezo-resistive material is also presented in order to predict the relative change in the resistance of the piezo-resistive material due to the pressure applied. PMID:25831088

The application of a piezo-resistive cardiorespiratory sensor system in an automobile safety belt.

Science.gov (United States)

Hamdani, Syed Talha Ali; Fernando, Anura

2015-03-30

Respiratory and heart failure are conditions that can occur with little warning and may also be difficult to predict. Therefore continuous monitoring of these bio-signals is advantageous for ensuring human health. The car safety belt is mainly designed to secure the occupants of the vehicle in the event of an accident. In the current research a prototype safety belt is developed, which is used to acquire respiratory and heart signals, under laboratory conditions. The current safety belt is constructed using a copper ink based nonwoven material, which works based on the piezo-resistive effect due to the pressure exerted on the sensor as a result of expansion of the thorax/abdomen area of the body for respiration and due to the principle of ballistocardiography (BCG) in heart signal sensing. In this research, the development of a theoretical model to qualitatively describe the piezo-resistive material is also presented in order to predict the relative change in the resistance of the piezo-resistive material due to the pressure applied.

The Application of a Piezo-Resistive Cardiorespiratory Sensor System in an Automobile Safety Belt

Directory of Open Access Journals (Sweden)

Syed Talha Ali Hamdani

2015-03-01

Full Text Available Respiratory and heart failure are conditions that can occur with little warning and may also be difficult to predict. Therefore continuous monitoring of these bio-signals is advantageous for ensuring human health. The car safety belt is mainly designed to secure the occupants of the vehicle in the event of an accident. In the current research a prototype safety belt is developed, which is used to acquire respiratory and heart signals, under laboratory conditions. The current safety belt is constructed using a copper ink based nonwoven material, which works based on the piezo-resistive effect due to the pressure exerted on the sensor as a result of expansion of the thorax/abdomen area of the body for respiration and due to the principle of ballistocardiography (BCG in heart signal sensing. In this research, the development of a theoretical model to qualitatively describe the piezo-resistive material is also presented in order to predict the relative change in the resistance of the piezo-resistive material due to the pressure applied.

Automated recognition of rear seat occupants' head position using Kinect™ 3D point cloud.

Science.gov (United States)

Loeb, Helen; Kim, Jinyong; Arbogast, Kristy; Kuo, Jonny; Koppel, Sjaan; Cross, Suzanne; Charlton, Judith

2017-12-01

Child occupant safety in motor-vehicle crashes is evaluated using Anthropomorphic Test Devices (ATD) seated in optimal positions. However, child occupants often assume suboptimal positions during real-world driving trips. Head impact to the seat back has been identified as one important injury causation scenario for seat belt restrained, head-injured children (Bohman et al., 2011). There is therefore a need to understand the interaction of children with the Child Restraint System to optimize protection. Naturalistic driving studies (NDS) will improve understanding of out-of-position (OOP) trends. To quantify OOP positions, an NDS was conducted. Families used a study vehicle for two weeks during their everyday driving trips. The positions of rear-seated child occupants, representing 22 families, were evaluated. The study vehicle - instrumented with data acquisition systems, including Microsoft Kinect™ V1 - recorded rear seat occupants in 1120 driving 26 trips. Three novel analytical methods were used to analyze data. To assess skeletal tracking accuracy, analysts recorded occurrences where Kinect™ exhibited invalid head recognition among a randomly-selected subset (81 trips). Errors included incorrect target detection (e.g., vehicle headrest) or environmental interference (e.g., sunlight). When head data was present, Kinect™ was correct 41% of the time; two other algorithms - filtering for extreme motion, and background subtraction/head-based depth detection are described in this paper and preliminary results are presented. Accuracy estimates were not possible because of their experimental nature and the difficulty to use a ground truth for this large database. This NDS tested methods to quantify the frequency and magnitude of head positions for rear-seated child occupants utilizing Kinect™ motion-tracking. This study's results informed recent ATD sled tests that replicated observed positions (most common and most extreme), and assessed the validity of child

Child Passenger Safety (A Minute of Health with CDC)

Centers for Disease Control (CDC) Podcasts

Using the correct car seat for your child can be a lifesaver. This podcast discusses the importance of ensuring children are buckled up in car seats or booster seats that are appropriate for their age and size until adult seat belts fit properly.

Perceived risk and other predictors and correlates of teenagers' safety belt use during the first year of licensure.

Science.gov (United States)

Ouimet, Marie Claude; Morton, Bruce G Simons; Noelcke, Elizabeth A; Williams, Allan F; Leaf, William A; Preusser, David F; Hartos, Jessica L

2008-03-01

Teenagers have the lowest rate of safety belt use and the highest crash rate compared to other age groups. Past studies on teenagers' belt use have mostly been cross-sectional. The first goals of this study were to examine, at licensure, teenagers' and parents' perceptions of risk of crash/injury for newly licensed teenagers when driving unbelted and teenagers' perceived and parents' intended consequences for safety belt rule violations. In addition, the comparability of these variables to other risky driving behaviors was explored. The second goal was to evaluate the importance of these variables in the prediction of teenagers' belt use during the first year of licensure, relative to other factors related to belt use, including demographics and substance use. More than 2,000 parent-teenager dyads were interviewed by telephone, parents at permit and licensure and teenagers at permit, licensure, and 3, 6, and 12 months after licensure. Approximately a third of the teenagers reported at least once at 3, 6, or 12 months post-licensure not always using their safety belt in the past week. At licensure, participants' perceived risk of safety belt non-use was high and ranked among the behaviors most related to crash/injury for newly licensed teenagers, behind driving under the influence of alcohol or drugs. Parent-imposed consequences for safety belt rule violations were not as highly rated as parent-imposed consequences for driving under the influence of alcohol or drugs. Sequential logistic regression modeled the relationship between safety belt use and perceived risk and consequences of non-use, as well as other prospective predictors assessed at permit and licensure, and driving correlates measured after licensure. Teenagers' extreme perceived risk and parents' intended sure consequences for non-use were significant prospective predictors of regular use during the first year of licensure. Other significant predictors and correlates were race (White), high school grade

Auto Safety

Science.gov (United States)

... Safe Videos for Educators Search English Español Auto Safety KidsHealth / For Parents / Auto Safety What's in this ... by teaching some basic rules. Importance of Child Safety Seats Using a child safety seat (car seat) ...

30 CFR 77.1107 - Belt conveyors.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Belt conveyors. 77.1107 Section 77.1107 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY... § 77.1107 Belt conveyors. Belt conveyors in locations where fire would create a hazard to personnel...

Assessing child belt fit, volume II : effect of restraint configuration, booster seat designs, seating procedure, and belt fit on the dynamic response of the hybrid III 10-year-old ATD in sled tests.

Science.gov (United States)

2008-09-01

A total of 49 dynamic sled tests were performed with the Hybrid III 10YO to examine issues relating to child belt fit. The goals of these tests were to evaluate ATD response to realistic belt geometries and belt fit, develop methods for accurate, rep...

Child Passenger Safety (A Minute of Health with CDC)

Centers for Disease Control (CDC) Podcasts

2016-09-29

Using the correct car seat for your child can be a lifesaver. This podcast discusses the importance of ensuring children are buckled up in car seats or booster seats that are appropriate for their age and size until adult seat belts fit properly. .  Created: 9/29/2016 by MMWR.   Date Released: 9/29/2016.

Parental practice of child car safety in Enugu, Southeast Nigeria.

Science.gov (United States)

Ndu, K I; Ekwochi, U; Osuorah, D C; Ifediora, O C; Amadi, F O; Asinobi, I N; Okenwa, O W; Orjioke, J C; Ogbuka, F N; Ulasi, T O

2016-01-01

Child safety restraints and seat belts are regarded as the most successful safety and cost-effective protective devices available to vehicle occupants, which have saved millions of lives. This cross-sectional descriptive study evaluated the practice and use of child car restraints (CCRs) among 458 purposively selected respondents resident in two local government areas in Enugu State, Nigeria. Self-administered questionnaires were sent to parents of children attending private schools who owned a car. Chi-square and multivariate analyses were used to assess the determinants of the use of car restraints in children among respondents. In all, 56% and 45% of adults and children, respectively, used car restraints regularly. The awareness of child safety laws and actual use of age-appropriate CCRs among respondents was negatively and weakly correlated ( r =-0.121, P =0.310). Only respondent's use of seat belt during driving ( P =0.001) and having being cautioned for non-use of CCRs ( P =0.005) maintained significance as determinants of the use of CCRs in cars on multivariate analysis. The most frequent reasons given for the non-use of CCRs included the child being uncomfortable, 64 (31%); restraints not being important, 53 (26%), and restraints being too expensive, 32 (15%). Similarly, for irregular users, exceptions for non-use included the child being asleep (29%), inadequate number of CCRs (22%), and the child being sick (18%). There is a need for a strategy change to enforce the use of CCRs in Nigeria.

Effects of incentive programs to stimulate safety belt use : a meta-analysis.

NARCIS (Netherlands)

Hagenzieker, M.P. Bijleveld, F.D. & Davidse, R.J.

1997-01-01

The effects of campaigns using tangible incentives (rewards) to promote safety belt usage have been evaluated by means of a meta-analytic approach. Two coders extracted a total number of 136 short-term and 114 long-term effect sizes and coded many other variables from 34 journal articles and

Health Care providers and Teen Driving Safety: Topics Discussed and Educational Resources Used in Practice.

Science.gov (United States)

Dellinger, Ann M; West, Bethany A

2015-11-01

Traffic crashes are the leading cause of death among teens. Health care providers have an opportunity to address what works to keep teens safe on the road during the patient visit. An online survey was conducted of 1088 health care providers who saw patients at or near driving age. The survey assessed which road safety topics were discussed and which types of educational products were used most often. Family and general practice physicians represented 44.3% of the sample, followed by pediatricians (22.5%), nurse practitioners (17.6%), and internists (15.5%). Nearly all respondents (92.9%) reported addressing one or more driving safety factors (seat belt use, nighttime driving, fatigue, teen passengers, alcohol/drug use, speeding/reckless driving, and cell phone use/texting) with adolescent patients and/or their parents. Seat belt use was reported more often (83.7%) than other topics. The use of parent-teen driving agreements, a known effective intervention, was reported by less than 10% of respondents. Since health care providers expressed interest in receiving written resource materials, distribution of parent-teen driving agreements to health care providers might encourage greater uptake and use of this effective intervention.

Numerical simulation on flow field of nuclear safety grade 2 single-seat pneumatic diaphragm control valve

International Nuclear Information System (INIS)

Zhong Yun; Zhang Jige; Wang Dezhong; Shi Jianzhong

2010-01-01

The Computational Fluid Dynamics (CFD) method is employed to simulate numerically the steady flow and transient flow under variable openings of the nuclear safety grade 2 single-seat pneumatic diaphragm control valve, which is a sleeve valve. The steady simulations under rated condition tells that there is a large amount of vortex in the valve seat necking and around the valve cone, which leads to a much greater flow impact on the head of the valve cone and uneven pressure distribution on spool face. More consideration should be taken on the characteristics of the valve cone accordingly, when designing a valve of this kind. Then the transient flow under 100% and 40% openings is simulated numerically on the basis of steady simulations. The pulsation of the pressure magnitude at the points with large vorticity, in the valve seat necking and around the valve cone, is monitored. The main pulsation frequencies differ from the low natural frequencies of the model, which means that it is safe from leading to structural resonance. (authors)

Newborn Parent Based Intervention to Increase Child Safety Seat Use

Directory of Open Access Journals (Sweden)

Xiangxiang Liu

2016-08-01

Full Text Available This paper intends to assess the effect of a maternity department intervention on improvement of knowledge and use of child safety seats (CSS among newborn parents. An intervention study included three groups (one education plus free CSS intervention group, one education only group, and one control group. The participants were parents of newborns in the maternity department of two hospitals. Both of the intervention groups received a folded pamphlet of child passenger safety, a height chart and standardized safety education during their hospital stay after giving birth. The education plus free CSS intervention group received an additional free CSS and professional installation training at hospital discharge. The control group received a pamphlet with educational information about nutrition and food safety. Three months after enrollment, a telephone follow-up was conducted among participants in the three groups. Data on child passenger safety knowledge, risky driving behaviors, and use of CSS were evaluated before and after the intervention. A total of 132 newborn parents were enrolled in the study; of those, 52 (39.4% were assigned into the education plus free CSS intervention group, 44 (33.3% were in the education intervention only group, and 36 (27.3% were in the control group. No significant differences existed in demographics among the three groups. There was a significant difference in newborn parents’ child passenger safety knowledge and behaviors in the three groups before and after the intervention. In addition, the CSS use increased significantly in the education plus free CSS group after the intervention compared to parents in the education only or control groups. Education on safety, combined with a free CSS and professional installation training, were effective at increasing newborn parents’ knowledge and use of CSS. Future studies with larger sample sizes and longer follow-up are needed to determine a long-term effect of the

Newborn Parent Based Intervention to Increase Child Safety Seat Use

Science.gov (United States)

Liu, Xiangxiang; Yang, Jingzhen; Cheng, Fuyuan; Li, Liping

2016-01-01

This paper intends to assess the effect of a maternity department intervention on improvement of knowledge and use of child safety seats (CSS) among newborn parents. An intervention study included three groups (one education plus free CSS intervention group, one education only group, and one control group). The participants were parents of newborns in the maternity department of two hospitals. Both of the intervention groups received a folded pamphlet of child passenger safety, a height chart and standardized safety education during their hospital stay after giving birth. The education plus free CSS intervention group received an additional free CSS and professional installation training at hospital discharge. The control group received a pamphlet with educational information about nutrition and food safety. Three months after enrollment, a telephone follow-up was conducted among participants in the three groups. Data on child passenger safety knowledge, risky driving behaviors, and use of CSS were evaluated before and after the intervention. A total of 132 newborn parents were enrolled in the study; of those, 52 (39.4%) were assigned into the education plus free CSS intervention group, 44 (33.3%) were in the education intervention only group, and 36 (27.3%) were in the control group. No significant differences existed in demographics among the three groups. There was a significant difference in newborn parents’ child passenger safety knowledge and behaviors in the three groups before and after the intervention. In addition, the CSS use increased significantly in the education plus free CSS group after the intervention compared to parents in the education only or control groups. Education on safety, combined with a free CSS and professional installation training, were effective at increasing newborn parents’ knowledge and use of CSS. Future studies with larger sample sizes and longer follow-up are needed to determine a long-term effect of the intervention. PMID

The effectiveness of automatic belts in reducing fatality rates in Toyota Cressidas.

Science.gov (United States)

Nash, C E

1989-12-01

Toyota Cressidas have had motor driven automatic belts since 1981. Their observed use rates have been consistently close to 100%. This paper compares fatality rates in Toyota Cressidas with those in the similar Nissan Maximas (which are equipped with three-point manual belts) using the latest data from the Fatal Accident Reporting System. After making adjustments for differences in the average ages of front seat occupants of the two fleets, the Toyotas have a fatality rate that is about three-quarters that of the Nissans. From this, the fatality-reducing effectiveness for the Toyota automatic belts is estimated to be 40% with an uncertainty of +/- 8%. This effectiveness estimate is consistent with earlier estimates of automatic belt effectiveness.

Design and Evaluation Methods for Optimizing Ejection Seat Cushions for Comfort and Safety

Science.gov (United States)

1977-02-01

buttocks to the seat cushion or seat pan. Kohara , a Japaners Investigator discussed the problems of seating comfort and the measuren.ent of buttock/seat...loads In an unpublished report in 1965 (23) and subsequently In a magazine article In 1966 (24). Kohara was able to weasure pressures by means of...Isolation. Kohara has also studied the vibration Isolation requirements in high speed trains (23, 2’). Howeveri the seat cushion has been used only rarely in

Dynamics Analysis and Modeling of Rubber Belt in Large Mine Belt Conveyors

OpenAIRE

Gao Yang

2014-01-01

Rubber belt not only is one of the key components of belt conveyor, but also affects the overall performance of the core part. Research on dynamics analysis of large conveyor not only helps to improve the reliability and design level, but also can guide the rational selection of conveyor safety factor, and effectively reduce the cost of the conveyor belt. Based on unique viscoelastic properties of belt conveyor, it was simplified as one-dimensional viscoelastic rod in this study, and then a d...

Patient safety during assistant propelled wheelchair transfers: the effect of the seat cushion on risk of falling.

Science.gov (United States)

Okunribido, Olanrewaju O

2013-01-01

This article is a report of a study of the effect of the seat cushion on risk of falling from a wheelchair. Two laboratory studies and simulated assistant propelled wheelchair transfers were conducted with four healthy female participants. For the laboratory studies there were three independent variables: trunk posture (upright/flexed forward), seat cushion (flat polyurethane/propad low profile), and feet condition (dangling/supported), and two dependent variables: occupied wheelchair (wheelchair) center of gravity (CG), and stability. For the simulated transfers there was one independent variable: seat cushion (flat polyurethane/propad low profile), and one dependent variable: perception of safety (risk of falling). Results showed that the wheelchair CG was closer to the front wheels, and stability lower for the propad low profile cushion compared to the polyurethane cushion, when the participants sat with their feet dangling. During the simulated transfers, sitting on the propad low profile cushion caused participants to feel more apprehensive (anxious or uneasy) compared to sitting on the polyurethane cushion. The findings can contribute to the assessment of risk and care planning of non-ambulatory wheelchair users.

Evaluation of the five-year Bloomberg Philanthropies Global Road Safety Program in the Russian Federation.

Science.gov (United States)

Gupta, S; Paichadze, N; Gritsenko, E; Klyavin, V; Yurasova, E; Hyder, A A

2017-03-01

Road traffic injuries are a leading cause of morbidity and mortality in the world. In Russia, a road safety program was implemented in Lipetskaya and Ivanovskaya oblasts (regions) as part of a 10-country effort funded by Bloomberg Philanthropies. The program was focused on increasing seat belt and child restraint use and reducing speeding. The primary goals of this monitoring and evaluation study are to assess trends in seat belt use, child restraint use, and speed compliance in the two oblasts over the 5 years and to explore the overall impact of the program on road traffic injury and death rates. Primary data via roadside observations and interviews, and secondary data from official government sources were collected and analyzed for this study. Our results indicate significant improvements in seat belt wearing and child seat use rates and in prevalence of speeding in both intervention oblasts. The observations were consistent with the results from the roadside interviews. In Lipetskaya, restraint use by all occupants increased from 52.4% (baseline, October 2010) to 77.4% (final round, October 2014) and child restraint use increased from 20.9% to 54.1% during the same period. In Ivanovskaya, restraint use by all occupants increased from 48% (baseline, April 2012) to 88.7% (final round, October 2014) and child restraint use increased from 20.6% to 89.4% during the same period. In Lipetskaya, the overall prevalence of speeding (vehicles driving above speed limit) declined from 47.0% (baseline, July 2011) to 30.4% (final round, October 2014) and a similar pattern was observed in Ivanovskaya where the prevalence of speeding decreased from 54.6% (baseline, March 2012) to 46.6% (final round, October 2014). Through 2010-2014, the road traffic crash and injury rates per 100,000 population decreased in Lipetskaya oblast (191.5 and 246.9 in 2010 and 170.4 and 208.6 in 2014, respectively) and slightly increased in Ivanovskaya oblast (184.4 and 236.0 in 2010 and 186.7 and 243

75 FR 37343 - Federal Motor Vehicle Safety Standards; Occupant Crash Protection

Science.gov (United States)

2010-06-29

... indicate that if manufacturers want to provide a voluntary signal that goes beyond what is specified in... through calendar year 2007. Of these 122 cases, only one fatality was attributed to what the agency... parents and caregivers could attach the child seat with the seat belt at such seating positions in...

76 FR 31803 - Airworthiness Directives; Koito Industries, Ltd., Seats and Seating Systems Approved Under...

Science.gov (United States)

2011-06-02

... CONTACT: Patrick Farina, Aerospace Engineer, Cabin Safety Branch, ANM-150L, FAA, Los Angeles Aircraft... understands that the FAA considers this phased testing structure as an acceptable testing plan, but also... the suspect seats were witnessed by FAA ``delegates'' (designated engineering representatives (DERs...

Compatibility of booster seats and vehicles in the U.S. market.

Science.gov (United States)

Bing, Julie A; Agnew, Amanda M; Bolte, John H

2018-05-19

The objective of this study was to analyze booster and rear vehicle seat dimensions to identify the most frequent compatibility problems. Measurements were collected from 40 high-back and backless boosters and 95 left rear and center rear row seating positions in 50 modern vehicles. Dimensions were compared for 3,800 booster/vehicle seat combinations. For validation and estimation of tolerance and correction factors, 72 booster installations were physically completed and compared with measurement-based compatibility predictions. Dimensions were also compared to the International Organization for Standardization (ISO) volumetric envelopes of forward-facing child restraints and boosters. Seat belt buckles in outboard positions accommodated the width of boosters better than center positions (success rates of 85.4 and 34.7%, respectively). Adequate head restraint clearance occurred in 71.9 to 77.2% of combinations, depending on the booster's head support setting. Booster recline angles aligned properly with vehicle seat cushion angles in 71.5% of combinations. In cases of poor angle alignment, booster angles were more obtuse than the vehicle seat angles 97.7% of the time. Head restraint interference exacerbated angle alignment issues. Data indicate success rates above 90% for boosters being fully supported by the length of the seat cushion and for adequate height clearance with the vehicle roofline. Comparison to ISO envelopes indicates that most boosters on the U.S. market are taller and angled more obtusely than ISO target envelopes. This study quantifies some of the common interferences between boosters and vehicles that may complicate booster usage. Data are useful for design and to prioritize specific problem areas.

Enhancement of pressurizer safety valve operability by seating design improvement

International Nuclear Information System (INIS)

Moisidis, N.T.; Ratiu, M.D.

1994-01-01

Operating conditions specific to Pressurizer Safety Valves (PSVs) have led to numerous problems and have caused industry and NRC concerns regarding the adequacy of spring loaded self-actuated safety valves for Reactor Coolant System (RCS) overpressure protection. Specific concerns are: setpoint drift, spurious actuations and leakage. Based on testing and valve construction analysis of a Crosby model 6M6 PSV, it was established that the primary contributor to the valve problems is a susceptibility to weak seating. To eliminate spring instability, a new spring washer was designed, which guides the spring and precludes its rotation from the reference installed position. Results of tests performed on a prototype PSV equipped with the modified upper spring washer has shown significant improvements in valve operability and a consistent setpoint reproducibility to less than ±1% of the PSV setpoint (testing of baseline, unmodified valve, resulted in a setpoint drift of ±2%). Enhanced valve operability will result in a significant decrease in operating and maintenance costs associated with valve maintenance and testing. In addition, the enhanced setpoint reproducibility will allow the development of a nitrogen to steam correlation for future in-house PSV testing which will result in further reductions in costs associated with valve testing

Belt conveyors for bulk materials. 6th ed.

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The 16 chapters are entitled: Belt conveyor general applications economics; Design considerations; Characteristics and conveyability of bulk materials; Capacities, belt widths and speeds; Belt conveyor idlers; Belt tension and power engineering; Belt selection; Pulleys and shafts; Curves; Steep angle conveying; Belt cleaners and accessories; Transfer points; Conveyor motor drives and controls; Operation, maintenance and safety; Belt takeups; and Emerging technologies. 6 apps.

Digital Recovery Sequencer - Advanced Concept Ejection Seats

National Research Council Canada - National Science Library

Ross, David A; Cotter, Lee; Culhane, David; Press, Matthew J

2005-01-01

.... Continued usage of the Analog Sequencer is undesirable due to limitations with respect to its installed life, electronic component obsolescence, flexibility to accommodate seat safety improvements...

75 FR 31691 - Safety Standard for Infant Bath Seats: Final Rule

Science.gov (United States)

2010-06-04

... would actually make the requirement less restrictive than what is already in the voluntary standard. For... various water levels and possible head positions of occupants vs. angles of bath seats to determine what... instructional literature or warnings, it is foreseeable that caregivers will install the bath seat on a wet and...

Underutilization of occupant restraint systems in motor vehicle injury crashes: A quantitative analysis from Qatar.

Science.gov (United States)

El-Menyar, Ayman; Consunji, Rafael; Asim, Mohammad; Abdelrahman, Husham; Zarour, Ahmad; Parchani, Ashok; Peralta, Ruben; Al-Thani, Hassan

2016-01-01

Restraint systems (seat belts and airbags) are important tools that improve vehicle occupant safety during motor vehicle crashes (MVCs). We aimed to identify the pattern and impact of the utilization of passenger restraint systems on the outcomes of MVC victims in Qatar. A retrospective study was conducted for all admitted patients who sustained MVC-related injuries between March 2011 and March 2014 inclusive. Out of 2,730 road traffic injury cases, 1,830 (67%) sustained MVC-related injuries, of whom 88% were young males, 70% were expatriates, and 53% were drivers. The use of seat belts and airbags was documented in 26 and 2.5% of cases, respectively. Unrestrained passengers had greater injury severity scores, longer hospital stays, and higher rates of pneumonia and mortality compared to restrained passengers (P = .001 for all). There were 311 (17%) ejected cases. Seat belt use was significantly lower and the mortality rate was 3-fold higher in the ejected group compared to the nonejected group (P = .001). The overall mortality was 8.3%. On multivariate regression analysis, predictors of not using a seat belt were being a front seat passenger, driver, or Qatari national and young age. Unrestrained males had a 3-fold increase in mortality in comparison to unrestrained females. The risk of severe injury (relative risk [RR] = 1.82, 95% confidence interval [CI], 1.49-2.26, P = .001) and death (RR = 4.13, 95% CI, 2.31-7.38, P = .001) was significantly greater among unrestrained passengers. The nonuse of seat belts is associated with worse outcomes during MVCs in Qatar. Our study highlights the lower rate of seat belt compliance in young car occupants that results in more severe injuries, longer hospital stays, and higher mortality rates. Therefore, we recommend more effective seat belt awareness and education campaigns, the enforcement of current seat belt laws, their extension to all vehicle occupants, and the adoption of proven interventions that will assure sustained

Driver characteristics associated with child safety seat usage in Malaysia: a cross-sectional study.

Science.gov (United States)

Kulanthayan, S; Razak, Ahmad; Schenk, Ellen

2010-03-01

The rapidly motorizing environment in Malaysia has made child occupant safety a current public health concern. The usage of child safety seats (CSS) is a widely regarded intervention to enhance child occupant safety, yet no study has been conducted on CSS in Malaysia. This study aims to determine the CSS usage rates in Malaysia and to assess driver characteristics that are associated with CSS usage. Nine variables - urban versus rural study location, age, gender, marital status, educational status, monthly family income, number of children present in the vehicle, distance traveled to the study location, and attitude - were examined through a cross-sectional study of interviewing drivers of 230 vehicles transporting at least one child safety in Malaysia. The results indicate that interventional efforts should focus on educational programs geared toward drivers that are less educated or extended family members who inconsistently transport young children. Furthermore, any educational efforts could be strongly enhanced by legislation mandating the use of CSS. Every effort should be made to thoroughly assess the effectiveness of any educational or legislative activities that are implemented. Copyright 2009 Elsevier Ltd. All rights reserved.

Enhancement of pressurizer safety valve operability by seating design improvement

International Nuclear Information System (INIS)

Moisidis, N.T.; Ratiu, M.D.

1995-01-01

Operating conditions specific to pressurizer safety valves (PSVs) have led to numerous problems and have caused industry and NRC concerns regarding the adequacy of spring-loaded self-actuated safety valves for reactor coolant system (RCS) overpressure protection. Specific concerns are: setpoint drift, spurious actuations, and pressure protection. Specific concerns are: setpoint drift, spurious actuations, and leakage. Based on testing and valve construction analysis of a Crosby model 6M6 PSV (Moisidis and Ratiu, 1992), it was established that the primary contributor to the valve problems is a susceptibility to weak seating. To eliminate spring instability, a new spring washer was designed, which guides the spring and precludes its rotation from the reference installed position. Results of tests performed on a prototype PSV equipped with the modified upper spring washer has shown significant improvements in valve operability and a consistent setpoint reproducibility to less than ±1% of the PSV setpoint (testing of baseline, unmodified valve, resulted in a setpoint drift of ± 2%). Enhanced valve operability will result in a significant decrease in operating and maintenance costs associated with valve maintenance and testing. In addition, the enhanced setpoint reproducibility will allow the development of a nitrogen to steam correlation for future in-house PSV testing which will result in further reductions in costs associated with valve testing

Occupant Kinematics in Simulated Autonomous Driving Vehicle Collisions: Influence of Seating Position, Direction and Angle.

Science.gov (United States)

Kitagawa, Yuichi; Hayashi, Shigeki; Yamada, Katsunori; Gotoh, Mitsuaki

2017-11-01

This two-part study analyzed occupant kinematics in simulated collisions of future automated driving vehicles in terms of seating configuration. In part one, a frontal collision was simulated with four occupants with the front seats reversed. The left front seat occupant was unbelted while the others were belted. In part two of the study, occupant restraint was examined in various seating configurations using a single seat model with a three-point seatbelt. The seat direction with respect to impact was considered as forward, rearward, and lateral facing in 45 degree increments. The effect of seat recline was also studied in the forward-facing and rear-facing cases by assuming three positions: driving position, resting position and relaxed position. Occupants were represented by human body finite element models. The results of part one showed that the front seat (rear-facing) occupants were restrained by the seatback, resulting in T1 forward displacement less than 100 mm; the rear seat occupants were restrained by the seatbelt resulting larger T1 forward displacement more than 500 mm. The results of the part two showed the directional dependence of occupant restraint. Greater T1 displacements were observed when the occupant faced lateral or front oblique. However, the seatbelt provided some restraint in all directions considered. The seatback generated contact force to the occupant when it was in the impact direction, including the lateral directions. The relaxed position allowed increased excursion compared to the driving position when the occupant faced rearward, but the magnitude of this increase was lower with lower impact speed.

Putting road safety awareness into practice

CERN Multimedia

2003-01-01

To round off the series of articles and posters published as part of its road safety awareness campaign, CERN is organising two information and demonstration open days on 23 and 25 September. Can you brake in time ? Did you know that you are 21 times more at risk of being killed if you are not wearing a seat belt in the event of your car rolling over? All your questions on road safety will be answered at two special days that are being organized on 23 and 25 September. You will also be able to test your reflexes and your knowledge by taking part in demonstrations. The CERN Management attaches high priority to an improvement in safety standards on the Laboratory's roads. These two open days have been arranged to round off the road safety awareness and highway courtesy campaign which was launched last year. They are intended to provide us with an opportunity, through a more "hands-on" approach, of heightening our awareness of the risks associated with road traffic, of the legislation in force, and above all t...

Parental practice of child car safety in Enugu, Southeast Nigeria

Directory of Open Access Journals (Sweden)

Ndu KI

2016-11-01

Full Text Available KI Ndu,1,* U Ekwochi,1,* DC Osuorah,2,* OC Ifediora,3 FO Amadi,1 IN Asinobi,1 OW Okenwa,1 JC Orjioke,1 FN Ogbuka,1 TO Ulasi4 1Department of Paediatrics, Enugu State University of Science and Technology, Enugu State, Engu, Nigeria; 2Child Survival Unit, Medical Research Council UK, The Gambia Unit, Fajara, Gambia; 3Griffiths University Medical School, Gold Coast, QLD, Australia; 4Department of Paediatrics, Nnamdi Azikiwe University Teaching Hospital, Nnewi, Anambra State, Nigeria *These authors contributed equally to this work Abstract: Child safety restraints and seat belts are regarded as the most successful safety and cost-effective protective devices available to vehicle occupants, which have saved millions of lives. This cross-sectional descriptive study evaluated the practice and use of child car restraints (CCRs among 458 purposively selected respondents resident in two local government areas in Enugu State, Nigeria. Self-administered questionnaires were sent to parents of children attending private schools who owned a car. Chi-square and multivariate analyses were used to assess the determinants of the use of car restraints in children among respondents. In all, 56% and 45% of adults and children, respectively, used car restraints regularly. The awareness of child safety laws and actual use of age-appropriate CCRs among respondents was negatively and weakly correlated (r=–0.121, P=0.310. Only respondent’s use of seat belt during driving (P=0.001 and having being cautioned for non-use of CCRs (P=0.005 maintained significance as determinants of the use of CCRs in cars on multivariate analysis. The most frequent reasons given for the non-use of CCRs included the child being uncomfortable, 64 (31%; restraints not being important, 53 (26%, and restraints being too expensive, 32 (15%. Similarly, for irregular users, exceptions for non-use included the child being asleep (29%, inadequate number of CCRs (22%, and the child being sick (18

Active Head Restraints Used to Improve the Car Seats Safety in a Rear Impact Situation, in Accordance with the Requirements of EURO NCAP

Directory of Open Access Journals (Sweden)

D. Yu. Solopov

2014-01-01

Full Text Available This article is devoted to the urgent, presently, problem that is to ensure the best level of the passive safety of car seats with active head restraints, as well as to assess the effectiveness of such constructional designs. This is an impact-related task, to be, as a consequence, essentially nonlinear with large deformations, strains and accelerations.To solve this problem finite element models of three types of seat designs with active head restraints have been developed. When creating the simulation FEM a number of CAD (Computer Aided Design/CAE (Computer Aided Engineering software was used.This work was performed within the framework of the developed technique, which allows an efficient creation of the car seat designs with passive and active head restraints that meet requirements of the passive safety.The results of calculations and experiments allowed us to find that the active head restraint significantly reduced a NIC (Neck Injury Criterion value, namely up to 36.92 (4% when using the active headrest with articulated tilting couch, 29.23 (per 24% when using the active headrest with sliding pad, and 26.15 (31% when using the active head restraint, which is provided with an airbag. We have also managed to achieve significantly reduced head acceleration under impact.It was found that FEM seats with active head restraint, which is provided with an airbag, are the most secure because of the least NIC value under the impact (26.15.Presented in the article materials are used in teaching students at the department “Wheeled vehicles” of scientific and educational complex "Special engineering" in BMSTU.

76 FR 53648 - Federal Motor Vehicle Safety Standards: Occupant Crash Protection

Science.gov (United States)

2011-08-29

... lower attachment nonusers cited their lack of knowledge--not knowing what the anchorages were, that they... LATCH- equipped DSPs because many parents and caregivers still rely on lockable belts to keep their... indicated that they knew what to do with the seat belt. These drivers who preferred to install CRSs with...

Belt conveying of minerals

Energy Technology Data Exchange (ETDEWEB)

Stace, L.R.; Yardley, E.D. [University of Nottingham, Nottingham (United Kingdom). School of Civil Engineering

2008-02-15

A discussion of the history and economics of conveyor applications sets the scene. Conveyor design is investigated in detail, covering power requirements, belt tensioning, and hardware. Principles regarding construction and joining of belts are outlined and a helpful and practical overview of relevant standards, belt test methods, and issues surrounding standardisation is given. Conveyor belt systems can represent a significant operational hazard, so the authors have set out to highlight the important area of safety, with consideration given to fire/electrical resistance, as well as the interface between personnel and conveyor systems - including nip points and operational issues such as man-riding. Selected case studies illustrate some practical aspects of installation and operation, at Selby mine in the UK and Prosper-Haniel Colliery in Germany and others. 3 apps.

Experimental study on occupant evacuation in narrow seat aisle

Science.gov (United States)

Huang, Shenshi; Lu, Shouxiang; Lo, Siuming; Li, Changhai; Guo, Yafei

2018-07-01

Narrow seat aisle is an important area in the train car interior due to the large passenger population, however evacuation therein has not gained enough concerns. In this experimental study, the occupant evacuation of the narrow seat aisle area is investigated, with the aisle width of 0.4-0.6 m and the evacuation direction of forward and backward. The evacuation behaviors are analyzed based on the video record, and the discussion is carried out in the aspect of evacuation time, crowdedness, evacuation order, and aisle conflicts. The result shows that with the increasing aisle width, total evacuation time and the average specific evacuation rate decrease. The aisle is crowded for some time, with a large linear occupant densities. The evacuation order of each occupant is mainly related to the seat position. Moreover, it is found that the aisle conflicts can be well described by Burstedde's model. This study gives a useful benchmark for evacuation simulation of narrow seat aisle, and provides reference to safety design of seat area in train cars.

ANTHROPOMETRIC CHARACTERISTICS OF FLIGHT PERSONNEL FOR DESIGNING DAMPERS FOR SHOCKPROOF SEATS OF HELICOPTER CREWS.

Science.gov (United States)

Moiseev, Yu B; Ignatovich, S N; Strakhov, A Yu

The article discusses anthropometric design of shockproof pilot seats for state-of-the-art helicopters. Object of the investigation was anthropometric parameters of the helicopter aviation personnel of the Russian interior troops. It was stated that the body parameters essential for designing helicopter seat dampers are mass of the body part that presses against the seat in the seating position, and eye level above the seat surface. An uncontrolled seat damper ensuring shockproof safety to 95 % helicopter crews must be designed for the body mass contacting the seat of 99.7 kg and eye level above the seat of 78.6 cm. To absorb.shock effectively, future dampers should be adjustable to pilot's body parameters. The optimal approach to anthropometric design of a helicopter seat is development of type pilot' body models with due account of pilot's the flight outfit and seat geometry. Principle criteria of type models are body mass and eye level. The authors propose a system of type body models facilitating specification of anthropometric data helicopter seat developers.

Public Awareness Survey Recommendations of the NHTSA-GHSA Working Group

Science.gov (United States)

2011-07-01

The Governors Highway Safety Association (GHSA) and the National Highway Traffic Safety Administration (NHTSA) developed a basic set of survey questions including information on seat belt use, impaired driving, and speeding. These core questions can ...

Advocacy for booster seat legislation in Florida: a lesson in politics and policy formation.

Science.gov (United States)

Haring, R Sterling; Frattaroli, Shannon; Schneider, Eric B; Holland, M Becker; Vernick, Jon S

2015-04-01

MVCs are a major contributor to child injury and death. Infant restraint seats and child booster seats have been shown to reduce the odds of severe injury or death when used correctly. While all states have mandated the use of these restraint systems, the age at which a child can be legally restrained using an adult seat belt varies from state to state. Efforts to strengthen Florida's weak child restraint laws have failed for more than a decade; in the 2014 legislative session, advocates succeeded in raising the state's age requirement from 3 years to 5  years. While many factors contributed to this year's success, some key elements included efficient communication of supporting data, a strong and broad advocacy network and the leveraging of election year political rivalries. Efforts to further strengthen the law will continue into future legislative sessions. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Misuse of booster cushions - an observation study of children's performance during buckling up.

Science.gov (United States)

Osvalder, Anna-Lisa; Bohman, Katarina

2008-10-01

Booster cushions are effective tools to protect children from injuries in car crashes, but there remains a large amount of misuse. The aim of this study was to assess potential misuse of booster cushions in an observational laboratory study, and to identify whether booster cushion design, age or clothing had any effect. 130 Swedish children from the ages of 4-12 years participated. Each child buckled up on an integrated and on an aftermarket booster cushion in the rear seat. The older children also buckled up with seat belt only. Interviews, observations and body measurements were performed. Time to buckle up and amount of belt slack were registered. Photographs were taken to document misuse. Results showed that 77% failed to perform correct belt routing on the aftermarket cushion, independent of age, although they were familiar with this system. The misuse rate for the integrated cushion was only 4%. No misuse was found for seat belt only. Few children tightened the belt. The belt slack increased when wearing winter jackets. This indicates the importance of adding pretensioners to the rear seat. Sled tests with HIII&TNO 6y dummies were also performed for the most frequent misuse situations found. The main conclusion is that an integrated booster cushion has many advantages compared to an aftermarket cushion regarding both safety and comfort. It is easy and quick to handle, has few possibilities for misuse, has an intuitive design, the buckling up sequence is equal to buckling up with an ordinary seat belt, and younger children can buckle up correctly.

AUTOMATION OF CONVEYOR BELT TRANSPORT

Directory of Open Access Journals (Sweden)

Nenad Marinović

1990-12-01

Full Text Available Belt conveyor transport, although one of the most economical mining transport system, introduce many problems to mantain the continuity of the operation. Every stop causes economical loses. Optimal operation require correct tension of the belt, correct belt position and velocity and faultless rolls, which are together input conditions for automation. Detection and position selection of the faults are essential for safety to eliminate fire hazard and for efficient maintenance. Detection and location of idler roll faults are still open problem and up to now not solved successfully (the paper is published in Croatian.

Misuse of restraint systems for children in The Netherlands.

NARCIS (Netherlands)

Schoon, C.C. Huijskens, C.G. & Heijkamp, A.H.

1993-01-01

The Dutch Ministry of Transport and Public Works commissioned the SWOV Institute for Road Safety Research and TNO Road-Vehicles Research Institute to carry out a research project. The aim is to establish the extent and type of misuse of both child seats and standard seat belts. This paper deals only

Crash safety concerns for out-of-position occupant postures: A look toward safety in highly automated vehicles.

Science.gov (United States)

McMurry, Timothy L; Poplin, Gerald S; Shaw, Greg; Panzer, Matthew B

2018-04-09

Highly automated vehicle occupants will all be passengers and may be free to ride while in postures for which existing occupant safety systems such as seat belts and airbags were not originally designed. These occupants could therefore face increased risk of injury when a crash occurs. Given that current vehicles are capable of supporting a variety of occupant postures outside of the normal design position, such as reclined or turned passengers, an evaluation of current field data was performed to better understand the risks of being out of position. We investigated the frequency, demographics, and injury outcomes for out-of-position occupants using NASS-CDS. A matched analysis was performed to compare injury outcomes for out-of-position passengers with in-position drivers involved in similar crashes. Finally, case studies for out-of-position occupants were examined in the Crash Injury Research (CIREN) database. Only 0.5% of occupants in NASS-CDS with a coded posture were out of position at the time of crash. Of the out-of-position occupants, being turned or seated sideways was almost as likely as being reclined. Out-of-position occupants were younger and less likely to be belted than their in-position counterparts. Analysis of the injury data indicated a trend that being out of position was associated with an elevated risk for serious injury. However, the number of out-of-position occupants was too small to provide a definitive or statistically significant conclusion on injury outcome. Though highly automated vehicles may eventually reduce the number of crashes and traffic fatalities in the future, there will be a transition period when these vehicles remain at risk from collisions with human-driven vehicles. These crashes could cause higher than anticipated rates of injury if occupants are less likely to be belted or tend to be in positions for which restraints are not optimized. This study highlights the need for future research on occupant response and

Traffic Safety Facts - Research Note: Additional Analysis of National Child Restraint Use Special Study: Characteristics Of Those Not Restrained

Science.gov (United States)

2018-03-01

The National Child Restraint Use Special Study (NCRUSS) recorded the use of car seats and belt-positioning booster seats in children up to 8 years old in 4,167 vehicles. Observers approached vehicles that carried at least one child. They interviewed ...

Healthy Environments for Children

Science.gov (United States)

... AND BE SURE EVERYONE WEARS A HELMET WHEN BIKING. IN THE CAR, CHILDREN SHOULD SIT IN THE BACK SEAT AND ALWAYS FASTEN THEIR SEAT BELTS! 14 AND CHILDREN SHOULD BE TAUGHT TO SWIM FROM THE TIME THEY’RE SMALL. IT’S GOOD FOR THEIR HEALTH AND THEIR SAFETY. PROTECTING CHILDREN FROM DANGERS IN ...

30 CFR 57.4263 - Underground belt conveyors.

Science.gov (United States)

2010-07-01

....4263 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Fire Prevention and Control Firefighting Equipment § 57.4263 Underground belt conveyors. Fire protection shall be...

Car child safety seats use among Iranian children in Mashad.

Science.gov (United States)

Karbakhsh, Mojgan; Jarahi, Lida

2016-01-01

Despite the strong evidence of child safety seats (CSSs) effectiveness in reducing injuries, it is still rarely used in some societies. The purpose of this study was to determine prevalence and predictors of CSS use in Mashad, Iran. Five hundred ninety kindergarten children whose parents owned a car were enrolled in the study. Parents were asked about using CSS for their children, reasons for CSS use/non-use, demographics, history of road traffic injuries and receiving any advice on CSS. Of families, 25.5% expressed that they used CSS for their child at present or any time in the past, but only 6.3% of children travelled restrained in CSS at the time of study. Age-appropriate CSS use was reported in 14.5% of infants and 2.3% of 1-5-year-old children. A significant relationship was observed between lower child age, higher maternal education and high family income with CSS use. The main reasons for CSS none-use were reported as not feeling the need (42%), followed by its high price (22%). Use of CSS was uncommon. The financial concerns and information gap about the essential need for CSS should be considered as priorities for action especially among lower socio-economic groups of society.

CDC Vital Signs: Adult Seat Belt Use in the US

Science.gov (United States)

... gov . Vital Signs Topics Covered Alcohol Antibiotic Resistance Cancer Cardiovascular Diseases Diseases & Conditions Food Safety Healthcare-associated Infections Healthy Living HIV / AIDS Injury, Violence & Safety Motor Vehicle Safety Obesity ...

Dynamics Analysis and Modeling of Rubber Belt in Large Mine Belt Conveyors

Directory of Open Access Journals (Sweden)

Gao Yang

2014-10-01

Full Text Available Rubber belt not only is one of the key components of belt conveyor, but also affects the overall performance of the core part. Research on dynamics analysis of large conveyor not only helps to improve the reliability and design level, but also can guide the rational selection of conveyor safety factor, and effectively reduce the cost of the conveyor belt. Based on unique viscoelastic properties of belt conveyor, it was simplified as one-dimensional viscoelastic rod in this study, and then a discrete element model of conveyor systems was established. The kinetic equations of each discrete unit was derived using kinetic energy, potential energy of driving segment, bearing segment and return segment and equation of energy dissipation and Lagrange equation. Based on Wilson-q algorithm, the kinetic equation of DT1307-type ST2000's conveyor belt was solved by using Matlab to write computer programs. Research on the change rule of conveyor displacement, velocity, acceleration and dynamic tension during the boot process revealed the working mechanism of nonlinear viscoelastic, which lay the theoretical foundation for dynamic performance optimization of large belt conveyor. The calculation results were used to optimize design and analysis of conveyor system, the result showed that it could reduce the driven tension peaks about 12 %, save 5 % of overall manufacturing cost, which bring considerable profits for enterprises.

The dynamic response of human subjects while seated in car seats.

Science.gov (United States)

Pope, M H; Magnusson, M; Broman, N H; Hasson, T

1998-01-01

A pendulum impact method was used to establish the dynamic response of the seated subject. Threaded K wires were placed in the L3 spinous process. The gain and phase angle between the platform and the vertebra were established. The response of the subject was observed while seated on a platform and a variety of other seats. The seats were found to be very important in the attenuation of the impulse, leading to a higher transmissibility. Clinical Relevance Skeletal impact through the lower extremity is quite common in many occupations. The importance of posture and seat design in attenuation of impulses has been established.

Front versus rear seat placement of children aged 12 or younger within vehicles: a rural/urban comparison in North Dakota.

Science.gov (United States)

Huseth-Zosel, Andrea L

2012-01-01

Research has shown that rear-seated children are 36 to 40 percent safer than front-seated children. Because of the substantial differences in traffic safety culture that appear to exist in rural areas and the limited research regarding seat placement and rurality, this study seeks to contribute to the safety literature by determining at what rate children are riding in the front seat and whether differences exist between rural and urban areas in regards to child front seat placement. Current child placement frequencies within vehicles were ascertained through direct observations of morning child drop-offs at randomly selected urban and rural elementary schools in eastern North Dakota during November and December of 2009, with a focus on children aged 12 or younger. Two observers wearing orange safety vests and carrying observation sheets were stationed at each elementary school a minimum of 45 min prior to each school's designated start time. Based on the vehicles that entered the school's parking lot/drop-off circle and from which a minimum of one child exited, observers were instructed to record vehicle type, presence of children in the front seat appearing to be younger than 13 years old, availability of room in the back seat, and placement of other children in the vehicle. During November and December of 2009 a total of 537 vehicles were observed at urban schools and 150 vehicles were observed at rural schools. Of the 537 vehicles observed at urban schools, 28.7 percent had children seated in the front seat, whereas 41.3 percent of the 150 vehicles observed at rural schools had front-seated children. Significant urban/rural differences exist in child seat placement, with vehicles in rural areas much more likely to be carrying front-seated children than vehicles in urban areas. Based on a sample of vehicles observed at urban and rural elementary schools in North Dakota, the results of this study indicate that there are significant rural/urban differences in

Driver injury in near- and far-side impacts: Update on the effect of front passenger belt use.

Science.gov (United States)

Parenteau, Chantal S; Viano, David C

2018-04-03

This is a study that updates earlier research on the influence of a front passenger on the risk for severe driver injury in near-side and far-side impacts. It includes the effects of belt use by the driver and passenger, identifies body regions involved in driver injury, and identifies the sources for severe driver head injury. 1997-2015 NASS-CDS data were used to investigate the risk for Maximum Abbreviated Injury Scale (MAIS) 4 + F driver injury in near-side and far-side impacts by front passenger belt use and as a sole occupant in the driver seat. Side impacts were identified with GAD1 = L or R without rollover (rollover ≤ 0). Front-outboard occupants were included without ejection (ejection = 0). Injury severity was defined by MAIS and fatality (F) by TREATMNT = 1 or INJSEV = 4. Weighted data were determined. The risk for MAIS 4 + F was determined using the number of occupants with known injury status MAIS 0 + F. Standard errors were determined. Overall, belted drivers had greater risks for severe injury in near-side than far-side impacts. As a sole driver, the risk was 0.969 ± 0.212% for near-side and 0.313 ± 0.069% for far-side impacts (P impacts. The risk was 2.17 times greater with an unbelted passenger (NS). The driver's risk was 0.782 ± 0.431% with an unbelted passenger and 0.361% ± 0.114% with a belted passenger in far-side impacts. The risk was 1.57 times greater with an unbelted passenger (P impacts, the leading sources for AIS 4+ head injury were the left B-pillar, roof, and other vehicle. For far-side impacts, the leading sources were the other occupant, right interior, and roof (8.5%). Seat belt use by a passenger lowered the risk of severe driver injury in side impacts. The reduction was 54% in near-side impacts and 36% in far-side impacts. Belted drivers experienced mostly head and thoracic AIS 4+ injuries. Head injuries in the belted drivers were from contact with the side interior and the other occupant, even with a belted passenger.

Burn from car seat heater in a man with paraplegia: case report

Science.gov (United States)

Benjamin, Cheryl; Gittler, Michelle; Lee, Ray

2011-01-01

Objective/background Heated car seats are a common feature in newer automobiles. They are increasingly being recognized as potential hazards as there have been multiple reports of significant burns to its users. The potential for harm is considerably increased in those with impaired sensation with the possibility of a devastating injury. Methods Case report and literature review. Results A 26-year-old male with a T8 ASIA A paraplegia presented to the outpatient clinic for management of a hip burn. Two weeks prior to his visit he was driving a 2004 Jeep Cherokee for approximately 30 minutes. He was unaware that the driver's side seat warmer was set on high. He denied that his seat belt was in direct contact with the skin of his right hip. He presented to an acute care hospital that evening with a hip burn where he was prescribed silver sulfadiazine cream and instructed to apply it until his scheduled follow-up clinic visit. In clinic, the hip wound was unstageable with approximately 95% eschar. A dressing of bismuth tribromophenate in petrolatum was applied to the wound and he was instructed to change the dressing daily. This was later changed to an antimicrobial alginate dressing. The ulcer eventually healed. Conclusions This case illustrates the significant risk of car seat heaters in individuals with spinal cord injuries or neurological impairment who have decreased sensation. Additionally, it highlights an atypical area of potential for burn. Furthermore, it emphasizes the need for a heightened awareness for this unique and dangerous situation. PMID:21756574

The dynamic response of human subjects while seated in car seats.

OpenAIRE

Pope, M. H.; Magnusson, M.; Broman, N. H.; Hasson, T.

1998-01-01

A pendulum impact method was used to establish the dynamic response of the seated subject. Threaded K wires were placed in the L3 spinous process. The gain and phase angle between the platform and the vertebra were established. The response of the subject was observed while seated on a platform and a variety of other seats. The seats were found to be very important in the attenuation of the impulse, leading to a higher transmissibility. Clinical Relevance Skeletal impact through the lower ext...

Take your seats: Leftward asymmetry in classroom seating choice

Directory of Open Access Journals (Sweden)

Victoria Lynn Harms

2015-08-01

Full Text Available Despite an overall body symmetry, human behaviour is full of examples of asymmetry, from writing or gesturing to kissing and cradling. Prior research has revealed that theatre patrons show a bias towards sitting on the right side of a movie theatre. Two competing theories have attempted to explain this seating asymmetry: one posits that expectation of processing demand drives the bias; the other posits that basic motor asymmetries drive the bias. To test these theories we assessed the real-world classroom seating choices of university students using photographs. A bias for students to choose seats on the left side of the classroom was observed, in contrast to the right side bias observed in theatre seating studies. These results provide evidence in support of a processing-expectation bias.

THE REAR CAR SEAT SAFETY BELT: AN ERGONOMIC APPROACH

OpenAIRE

WILSON DE MORAES NOBRE JUNIOR

2005-01-01

Esta dissertação tem como hipótese que as deficiências de projeto do cinto e do habitáculo traseiros dos automóveis de passeio, do ponto de vista ergonômico, causam desconforto e constrangimento no uso ordinário do cinto de segurança, provocando seu uso errado, sua rejeição, e sujeitando os passageiros, em caso de acidentes, a lesões e à morte. Sobre a importância do uso do cinto, especialmente o do banco traseiro, se explica o conceito e a magnitude das...

Blast resistant vehicle seat

Science.gov (United States)

Ripley, Edward B

2013-02-12

Disclosed are various seats for vehicles particularly military vehicles that are susceptible to attack by road-bed explosive devices such as land mines or improvised explosive devices. The seats often have rigid seat shells and may include rigid bracing for rigidly securing the seat to the chassis of the vehicle. Typically embodiments include channels and particulate media such as sand disposed in the channels. A gas distribution system is generally employed to pump a gas through the channels and in some embodiments the gas is provided at a pressure sufficient to fluidize the particulate media when an occupant is sitting on the seat.

An educational intervention in road safety among children and teenagers in Mexico.

Science.gov (United States)

Treviño-Siller, S; Pacheco-Magaña, L E; Bonilla-Fernández, P; Rueda-Neria, C; Arenas-Monreal, L

2017-02-17

The purpose of this article is to describe a public school-based educational intervention (EI) designed to increase knowledge, improve attitudes, and change practices related to road safety. We used a mixed-methods evaluation of a road traffic safety baseline diagnosis conducted in 4 public schools, 2 primary and 2 secondary. Research was organized into 4 phases: (1) diagnosis, (2) EI design, (3) implementation, and (4) evaluation. We used convenience sampling (n = 219 students) across schools and applied a pre-/posttest design based on quantitative and qualitative data. The former related to surveys on road safety experiences, knowledge, attitudes, and practice and the latter to observation checklists, community mapping, ethnography, and focus groups. To compare pre-post scores, we used multilevel mixed-effect ordinal logistic regressions. We developed data matrices, field notes, and systematized community mapping. We also transcribed focus group discussions, generated categories, and carried out thematic analysis. Ethnography indicated poor sidewalk conditions, no helmet or seat belt use, overcrowded public transportation, and no traffic lights or proper signals. Pedestrians did not use sidewalks and crossed streets unsafely. Subsequent to the intervention, however, the study population showed significant changes in their knowledge, practices, and attitudes. They identified road traffic incidents (RTIs) as the first cause of death among children and youth, and most understood that the solution to the problem was incumbent upon each and every individual. They also displayed increased perceptions of danger in practices such as traveling on overcrowded public transportation, failing to wear seat belts in cars and helmets on motorcycles, crossing the street while using mobile phones or playing with friends, and riding with drunk drivers. Changes varied according to gender, and students reported being able to carry out safe practices only when they were in control of

The Effects of Microgravity on Seated Height (Spinal Elongation)

Science.gov (United States)

Young, K. S.; Rajulu, S.

2011-01-01

ABSTRACT Many physiological factors, such as spinal elongation, fluid shifts, bone atrophy, and muscle loss, occur during an exposure to a microgravity environment. Spinal elongation is just one of the factors that can also affect the safety and performance of a crewmember while in space. Spinal elongation occurs due to the lack of gravity/compression on the spinal column. This allows for the straightening of the natural spinal curve. There is a possible fluid shift in the inter-vertebral disks that may also result in changes in height. This study aims at collecting the overall change in seated height for crewmembers exposed to a microgravity environment. During previous Programs, Apollo-Soyuz Test Project (ASTP) and Skylab, spinal elongation data was collected from a small number of subjects in a standing posture but were limited in scope. Data from these studies indicated a quick increase in stature during the first few days of weightlessness, after which stature growth reached a plateau resulting in up to a 3% increase of the original measurement [1-5]. However, this data was collected only for crewmembers in standing posture and not in a seated posture. Seated height may have a different effect than standing height due to a change in posture as well as due to a compounded effect of wearing restraints and a potential compression of the gluteal area. Seated height was deemed as a critical measurement in the design of the Constellation Program s (CxP) Crew Exploration Vehicle (CEV), called Orion which is now the point-of-departure vehicle for the Multi-Purpose Crew Vehicle (MPCV) Program; therefore a better understanding of the effects of microgravity on seated height is necessary. Potential changes in seated height that may not have impacted crew accommodation in previous Programs will have significant effects on crew accommodation due to the layout of seats in the Orion.. The current and existing configuration is such that the four crewmembers are stacked two by

Views of US drivers about driving safety.

Science.gov (United States)

Williams, Allan F

2003-01-01

To assess how drivers view dangers on the highway, what motivates them to drive safely, how they say they reduce their crash and injury risk, and how they rate their own driving skills. Most drivers rated their skills as better than average. The biggest motivating factor for safe driving was concern for safety of others in their vehicle, followed by negative outcomes such as being in a crash, increased insurance costs, and fines. The greatest threats to their safety were thought to be other drivers' actions that increase crash risk such as alcohol impairment or running red lights. In terms of reducing crashes and injuries, drivers tended to focus on actions they could take such as driving defensively or using seat belts. There was less recognition of the role of vehicles and vehicle features in crash or injury prevention. Knowing how drivers view themselves and others, their concerns, and their motivations and techniques for staying out of trouble on the roads provides insight into the difficulty of changing driving practices.

A field-based approach for examining bicycle seat design effects on seat pressure and perceived stability.

Science.gov (United States)

Bressel, Eadric; Bliss, Shantelle; Cronin, John

2009-05-01

The purpose of this study was to investigate the effect of various bicycle seat designs on seat pressure and perceived stability in male and female cyclists using a unique field-based methodology. Thirty participants, comprising male and female cyclists, pedaled a bicycle at 118W over a 350m flat course under three different seat conditions: standard seat, a seat with a partial anterior cutout, and a seat with a complete anterior cutout. The pressure between the bicycle seat and perineum of the cyclist was collected with a remote pressure-sensing mat, and perceived stability was assessed using a continuous visual analogue scale. Anterior seat pressure and stability values for the complete cutout seat were significantly lower (p<0.05; 62-101%) than values for the standard and partial cutout designs. These findings were consistent between males and females. Our results would support the contention that the choice of saddle design should not be dictated by interface pressure alone since optimal anterior seat pressure and perceived seat stability appear to be inversely related.

Misuse of restraint systems for children and adults.

NARCIS (Netherlands)

Schoon, C.C.

1992-01-01

A study is described of the use of child seats in The Netherlands. Four types are used: a) rearward facing baby seat, b) seat with harness belt, c) seat without harness belt but with a shield of foam over which the belt is strapped and d) booster cushion. Seats were examined for the way in which

Design of belt conveyors in bulk terminal applications. Part II

Energy Technology Data Exchange (ETDEWEB)

Goodwin, P J; Ramos, C M

1986-04-01

The main design parameters used for belt conveyors in harbour applications are discussed. Conveyor belting including the carcass, belt cover, belt tension and speed, and safety factors, idlers, conveyor pulleys, motors, fluid couplings and drive arrangements are considered. Technical factors are briefly outlined for the designer to consider to achieve minimum acceptable component service life. A method is discussed to reduce coal degradation investigated using a test chute designed for the purpose of minimizing sized coal degradation at transfer points in the refurbishing of the Durban Coal Terminal. 24 references.

Application of a bus seat buffer to mitigate frontal crash effects

Science.gov (United States)

Stanisławek, Sebastian; Dziewulski, Paweł; Sławiński, Grzegorz

2018-01-01

The paper considers the problem of coach occupant safety during crash events. The authors present a simple low-cost seat buffer concept which may mitigate the effects of frontal impact. The method of computer simulation was chosen to solve the problem efficiently. The Finite Element Method (FEM) implemented in the LS-DYNA commercial code was used. The testing procedure was based on European Commission regulations, under which vehicles move at a defined speed. Simulations have shown that seat occupants suffer serious trauma during a crash, with the head experiencing relatively high acceleration, thus resulting in an HIC36 of 1490. The installation of a protective buffer mounted on the upper part of the seat reduced the HIC36 to only 510. However, in its current form it does not meet the requirements of the regulations. Further modifications to the overlay shape and structure are essential in order to better improve the deceleration of passengers' bodies. Moreover, a detailed model of seats and their anchorage should be taken into account. A more flexible structure should provide more positive and more accurate results.

Practices, attitudes and perceptions toward road safety in yerevan, republic of armenia.

Science.gov (United States)

Chekijian, Sharon Anoush; Truzyan, Nune

2012-01-01

: To determine knowledge and attitudes regarding traffic safety devices, measures, and legislation in the general population in Yerevan, Republic of Armenia. : We conducted a baseline random digit dial fixed line telephone verbal survey of Yerevan households in April 2009 with a follow-up survey in May 2010. Survey domains included restraint use, motor vehicle crash experiences, and attitudes regarding traffic safety. : In the initial survey, of 2137 numbers dialed, 436 persons were reached and 390 (90%) agreed to participate. Of survey respondents, 90% percent of household cars had seatbelts, while 47% had airbags. Twenty-four percent always or usually wore a seatbelt when driving, 21% wore a belt as a passenger. 39% were unaware of child restraints. Of the 61% who were aware of child restraints, only 32% had ever used one. A follow-up survey was conducted one year later after enforcement efforts were increased. In the follow-up survey, 81% percent always or usually wore a seatbelt when driving, and 69% wore a belt as a passenger. There was no significant increase of awareness or use of child restraints in the follow-up survey. : Although cars in Yerevan have seat belts, the majority of drivers and passengers prior to the intervention did not use them. Knowledge and use of child restraints was poor. The follow-up survey conducted after an enforcement campaign was underway in Yerevan showed that improved enforcement greatly increased awareness and compliance with current legislation. This study provides vital baseline information for the formulation of future policy. It also highlights the need for a multi-dimensional road traffic safety initiative through public educational campaigns, enforcement of current laws, and development of novel prevention policies and regulations.

The influence of parental education and other socio-economic factors on child car seat use.

Science.gov (United States)

Rok Simon, Mateja; Korošec, Aleš; Bilban, Marjan

2017-03-01

The behaviour of parents in ensuring car passenger safety for their children is associated with socio-economic (SE) status of the family; however, the influence of parental education has rarely been researched and the findings are contradictory. The aim of the study was to clarify whether parental education influences the use of a child car seat during short rides. A cross-sectional survey was carried out in outpatient clinics for children's healthcare across Slovenia. 904 parents of 3-year-old children participated in the study; the response rate was 95.9%. A self-administered questionnaire was used. A binary multiple logistic regression was applied to assess the association between parental unsafe behaviour as dependent variable, and education and other SE factors as independent variables. 14.6% of parents did not use a child car seat during short rides. Families where mother had low or college education had higher odds of the non-use of a child car seat than families where mother had a university education. Single-parent families and those who lived in areas with low or medium SE status also had higher odds of the non-use of a child car seat. Low educational attainment influences parents' behaviour regarding the non-use of a child car seat. Low parental education is not the only risk factor since some highly educated parents also have high odds of unsafe behaviour. All parents should therefore be included in individually tailored safety counselling programmes. SE inequalities could be further reduced with provision of free child car seats for eligible families.

Promote buckling up and save a child's life

African Journals Online (AJOL)

safety, this number has not improved significantly from 1991 to 2015. (Fig. 2).[6]. Seat belts ... The World Health Organization's Global Status Report on Road Safety 2015 rated the African continent's roads the world's most dangerous. .... likely to bend rather than break, resulting in energy from the collision being transferred ...

Management of cervical spine injuries in young children: lessons learned.

Science.gov (United States)

Smith, Jodi L; Ackerman, Laurie L

2009-07-01

Previous studies have shown that the correct use of car safety seats can protect infants and children from vehicular injury. Although child passenger devices are increasingly used in the US, motor vehicle crashes continue to be the leading cause of death and acquired disability in infants and children younger than 14 years of age. These events are likely related, at least in part, to the high percentage of children who are unrestrained or improperly restrained. The authors present 2 cases of severe cervical spine trauma in young children restrained in car safety seats during a motor vehicle crash: 1) a previously healthy 14-month-old girl who was improperly restrained in a forward-facing booster seat secured to the vehicle by a lap belt, and 2) a previously healthy 30-month-old girl who was a rear seat passenger restrained in a car safety seat. This study points out the unique challenges encountered in treating cervical spine injuries in infants and young children, as well as the lessons learned, and emphasizes the significance of continuing efforts to increase family and public awareness regarding the importance of appropriate child safety seat selection and use.

Development of a method for rating climate seat comfort

Science.gov (United States)

Scheffelmeier, M.; Classen, E.

2017-10-01

The comfort aspect in the vehicle interior is becoming increasingly important. A high comfort level offers the driver a good and secure feeling and has a strong influence on passive traffic safety. One important part of comfort is the climate aspect, especially the microclimate that emerges between passenger and seat. In this research, different combinations of typical seat materials are used. Fourteen woven and knitted fabrics and eight leathers and its substitutes for the face fabric layer, one foam, one non-woven and one 3D spacer for the plus pad layer and for the support layer three foam types with variations in structure and raw material as well as one rubber hair structure were investigated. To characterise this sample set by thermo-physiological aspects (e.g. water vapour resistance Ret, thermal resistance Rct, buffering capacity of water vapour Fd) regular and modified sweating guarded hotplates were used according to DIN EN ISO 11092. The results of the material characterisation confirm the common knowledge that seat covers out of textiles have better water vapour resistance values than leathers and its substitutes. Subject trials in a driving simulator were executed to rate the subjective sensation while driving in a vehicle seat. With a thermal, sweating Manikin (Newton Type, Thermetrics) objective product measurements were carried out on the same seat. Indeed the subject trials show that every test subject has his or her own subjective perception concerning the climate comfort. The results of the subject trials offered the parameters for the Newton measuring method. Respectively the sweating rate, sit-in procedure, ambient conditions and sensor positions on and between the seat layers must be comparable with the subject trials. By taking care of all these parameters it is possible to get repeatable and reliable results with the Newton Manikin. The subjective feelings of the test subjects, concerning the microclimate between seat and passenger, provide

Restraint use by car occupants: Great Britain, 1982-91.

NARCIS (Netherlands)

Broughton, J.

1992-01-01

One of the major developments in road safety in Great Britain during the last decade has been the increasing use of seat belts by people travelling in cars. This has been achieved by legislation, with supporting publicity.

Injury severity and seating position in accidents with German EMS helicopters.

Science.gov (United States)

Hinkelbein, Jochen; Spelten, Oliver; Neuhaus, Christopher; Hinkelbein, Mandy; Özgür, Enver; Wetsch, Wolfgang A

2013-10-01

Accident rates and fatality rates for Helicopter Emergency Medical Service (HEMS) missions have been investigated recently, but none of these studies considered the influence of the seating position in the helicopter. The aim of the present descriptive and observational study was to analyze injury severity depending on the seating position during HEMS accidents in Germany. Data from the German Federal Agency for Flight Accident Investigation was gathered for a period of 40 years (from 1970 to 2009). The seating position in the aircraft during the accident and the resulting injury severity (i.e., 1=no; 2=slight; 3=severe; and 4=fatal) were recorded. Injury severity was compared using the Fisher's exact test. P values accidents were investigated (n=61 accidents did not lead to any injuries in the occupants, n=7 accidents resulted in minor, and n=6 in severe injuries, and lethal injuries resulted from n=15 accidents). The occupant in the "patient" position was most likely to suffer from deadly injuries (44.9%), followed by the HEMS crew member rear seat (25.0%), compared to lower lethality rates in the other seating positions (9.4-11.2%). Sitting on the HEMS crew member rear seat also was associated with the highest percentage of severe and minor injuries (12.5% each). In HEMS accidents, the patients' position and the HEMS crew member rear seat were found to be at the highest risk for fatal or severe injuries. These results support the urgent requirement of a large international data base for HEMS accidents as a basis for further studies to improve the safety in HEMS missions. Copyright © 2013 Elsevier Ltd. All rights reserved.

EVALUATING EXTREMELY LOW FREQUENCY MAGNETIC FIELDS IN THE REAR SEATS OF THE ELECTRIC VEHICLES.

Science.gov (United States)

Lin, Jun; Lu, Meng; Wu, Tong; Yang, Lei; Wu, Tongning

2018-03-23

In the electric vehicles (EVs), children can sit on a safety seat installed in the rear seats. Owing to their smaller physical dimensions, their heads, generally, are closer to the underfloor electrical systems where the magnetic field (MF) exposure is the greatest. In this study, the magnetic flux density (B) was measured in the rear seats of 10 different EVs, for different driving sessions. We used the measurement results from different heights corresponding to the locations of the heads of an adult and an infant to calculate the induced electric field (E-field) strength using anatomical human models. The results revealed that measured B fields in the rear seats were far below the reference levels by the International Commission on Non-Ionizing Radiation Protection. Although small children may be exposed to higher MF strength, induced E-field strengths were much lower than that of adults due to their particular physical dimensions.

Truck drivers' opinion on road safety in Tanzania--a questionnaire study.

Science.gov (United States)

Kircher, Katja; Andersson, Jan

2013-01-01

Even though the traffic fatality risk (fatalities per 100,000 inhabitants) in Tanzania is quite low, the fatality rate (fatalities per 10,000 vehicles) is one of the highest in the world. With increasing vehicle density this means that the number of people dying in traffic will increase dramatically in the near future. Therefore, it is important to implement measures to increase traffic safety as soon as possible, and in order to be able to do this in an efficient way, it is important to investigate where the main problems lie. Within the European Union (EU) project ASSET-Road a questionnaire study on road safety was conducted with 250 truck drivers in Tanzania. The study was done to increase the knowledge about the situation of the Tanzanian truckers, who are the most frequent road users in the country. The drivers were interviewed in 3 different towns in southern Tanzania, and participation was voluntary. The questionnaire treated demographics, the state of the drivers' vehicles, the frequency of breakdowns, and the maintenance of the vehicles. Further questions concerned driver behavior, crash involvement, crash risk, and crash mitigation. The drivers who participated in the study were predominantly male and their average age was 36 years. Truck drivers reported driving 10.6 h without a break on average, with several drivers reporting that they had to drive 24 h without rest. Around 40 percent of the trucks did not have any seat belts installed, with a larger share of older trucks lacking belts. Most of the drivers who had seat belts reported using them, however. Almost 40 percent of the drivers reported being involved in at least one crash, and 45 percent of those drivers had experienced fatal crashes. This underlines that the crash frequency per vehicle is very high, and the results are often severe, especially when heavy vehicles are involved. When asked what the 3 most common crash causations were, driver-related causes were named frequently. Drivers were

Determination of acceleration for belt conveyor speed control in transient operation

NARCIS (Netherlands)

He, D.; Pang, Y.; Lodewijks, G.

2016-01-01

Speed control has been found a feasible mean to reduce the energy consumption of belt conveyors. However, the current research has not taken the determination of the acceleration in transient operation into account sufficiently. With respect to the belt tension rating, demanded safety factor and the

Comfort, experience, physiology and car seat innovation : Theory, Design and Evaluation

NARCIS (Netherlands)

Franz, M.M.

2010-01-01

The development process of car seats is very complex and many factors have to be considered in the development, such as anthropometry, physiology, safety, design and comfort. A factor making it more complex is the fact that future cars should be more sustainable, making the need for weight reduction

75 FR 12123 - Federal Motor Vehicle Safety Standards; Side Impact Protection; Fuel System Integrity; Electric...

Science.gov (United States)

2010-03-15

... Restraint Position for the SID-IIs iii. Adjustable Seat Belt Shoulder Anchor iv. Adjustable Steering Wheels... Definitions 2. Test Dummy Set-Up i. SID-IIs A. Hip Point Specification B. Knee and Ankle Spacing C. Pelvic...

DEVELOPMENT OF THE TEST METHODS OF THE CONVEYOR BELTS USED IN ENVIRONMENTS ENDANGERED BY EXPLOSION HAZARDS

Directory of Open Access Journals (Sweden)

Florin Adrian PĂUN

2012-05-01

Full Text Available Conveyor belts are used for a long period of time in the industry branches where potentially explosive atmospheres could occur. Dangerous phenomena which can be in direct connection with the use of conveyor belts are the ones regarding: - sparks influence over the coating layer and/or resistance internal structure of the stopped conveyor belt; - propagation of a flame along the length of a conveyor belt that was exposed to a energy source relative high like a fire or due to blockage of a conveyor belt as a result of the driving mechanism still operating, that generate a local heating of the conveyor belt in contact with the driving drum, rollers or any other heating source generated by friction. Determining the safety parameters characteristic of the conveyor belts by employing test methods allows assessment of the safety level as well as certification of their explosion protection quality when used in environments with explosion danger.

[The use of seatbelts and child seats in drivers and passengers of motor vehicles in four metropolitan areas in Mexico].

Science.gov (United States)

Cervantes-Trejo, Arturo; Leenen, Iwin

2015-01-01

To estimate the rate of seatbelt and child seat use in drivers and passengers of motor vehicles in four metropolitan areas in Mexico (Guadalajara, León, Monterrey and Mexico City). To evaluate the impact of the Mexican Initiative for Road Safety (IMESEVI) in this respect. Data were collected at the start of IMESEVI (June 2008) and one year after the program's implementation (October 2009) in the four participating metropolitan areas. In particular, the use of seatbelts and child seats was observed in occupants of automobiles, station wagons, and light trucks. The sample included 28,412 (pre) and 52,274 (post) individuals, of which 1,454 (pre) and 1,679 (post) were younger than five years old. The data analysis was based on a hierarchical logistic model. Globally, the probability of using either safety device is 46% (95% CI: 43-49%) at baseline and 52% (95% CI: 48-55%) at the post measurement, with large differences, though, among the four participating metropolitan areas. Factors that significantly affect their use include the individual's position in the vehicle, the type and age of the vehicle, and the individual's sex. Child seat use is very limited. At baseline, about 17% (95% CI: 11-25%) of children below five years old travelled in a special seat, with this number increasing to 26% (95% CI: 19-34%) after the implementation of IMESEVI. Child seat use for children above four years is virtually nonexistent. Continued efforts are required to raise the public awareness of the importance of using safety devices, especially for passengers in the back of the car as well as with respect to the use of adapted seats for small children.

30 CFR 75.1101 - Deluge-type water sprays, foam generators; main and secondary belt-conveyor drives.

Science.gov (United States)

2010-07-01

... and secondary belt-conveyor drives. 75.1101 Section 75.1101 Mineral Resources MINE SAFETY AND HEALTH... Fire Protection § 75.1101 Deluge-type water sprays, foam generators; main and secondary belt-conveyor... be installed at main and secondary belt-conveyor drives. ...

Applications of Mechatronics in Seating Furniture

Directory of Open Access Journals (Sweden)

Hynek Maňák

2014-01-01

Full Text Available Mechatronics is gradually being used in different fields of the production process and final products. In the field of home seating furniture, it has not been formally declared as such yet. The purpose of further development of seating furniture is to improve its ergonomic parameters, to improve user comfort in controlling and using seating furniture or to provide new additional functions of seating furniture. Application of mechatronic principles can be presumed within the framework of this development. An analysis of the current state of reclining seating furniture, which uses mechanical and electromechanical positioning mechanisms, is conducted in order to formulate possible fields of applying mechatronics. The analysis defines individual ergonomic parameters which are influenced in reclining of seating furniture. This analysis is used as a basis for formulating a hypothesis describing potential development fields of applying mechatronics in home seating furniture.

A Motion Control of a Robotic Walker for Continuous Assistance during Standing, Walking and Seating Operation

OpenAIRE

Chugo, Daisuke; Takase, Kunikatsu

2010-01-01

In this paper, we develop an active walker system for standing, walking and seating operation continuously which cooperates the developed standing assistance system with safety and stability. For realizing these conditions, our walker coordinates the assisting position cooperating the standing assistance manipulator according to the posture of the patient. Furthermore, our walker adjusts a seating position when the patient sit down which has high risk for falling down. Using our proposed syst...

Responses and Injuries to PMHS in Side-Facing and Oblique Seats in Horizontal Longitudinal Sled Tests per FAA Emergency Landing Conditions.

Science.gov (United States)

Humm, John R; Yoganandan, Narayan; Pintar, Frank A; DeWeese, Richard L; Moorcroft, David M; Taylor, Amanda M; Peterson, Brian

2016-11-01

The objective of the present exploratory study is to understand occupant responses in oblique and side-facing seats in the aviation environment, which are increasingly installed in modern aircrafts. Sled tests were conducted using intact Post Mortem Human Surrogates (PMHS) seated in custom seats approximating standard aircraft geometry. End conditions were selected to represent candidate aviation seat and restraint configurations. Three-dimensional head center-of-gravity linear accelerations, head angular velocities, and linear accelerations of the T1, T6, and T12 spinous processes, and sacrum were obtained. Three-dimensional kinematics relative to the seat were obtained from retroreflective targets attached to the head, T1, T6, T12, and sacrum. All specimens sustained spinal injuries, although variations existed by vertebral level. While the tension mechanism was associated with cervical spine injuries, complex distraction-coupled with bending and tension was attributed to thoracolumbar spine injuries. Skeletal fractures to the ribcage were attributed to compression induced by the restraint from the seatbelt, the presence of the armrest, and/or severe motions of the unconstrained torso. Pelvic injuries were also attributed to restraint offered by the lap belt on the accelerating torso-pelvis complex in the absence of the armrest. Lower extremity injuries occurred due to the unconstrained motion (flailing mechanism). These results serve as an initial dataset to understand the kinematics of different body regions, injuries and patterns, and potential injury mechanisms describing PMHS responses in the aviation environment.

Het gebruik van autogordels en factoren die daarbij een rol spelen : een internationale vergelijking.

NARCIS (Netherlands)

Mäkinen, T. Wittink, R.D. & Hagenzieker, M.P.

1991-01-01

The purpose of this study was to define factors that contribute to the use or non-use of seat belts. Legislation prescribing compulsory seat belt usage is one of the most important factors. Promotion of the use of seat belts without this legislation is very difficult and time-consuming. So far, the

Standardized error severity score (ESS) ratings to quantify risk associated with child restraint system (CRS) and booster seat misuse.

Science.gov (United States)

Rudin-Brown, Christina M; Kramer, Chelsea; Langerak, Robin; Scipione, Andrea; Kelsey, Shelley

2017-11-17

Although numerous research studies have reported high levels of error and misuse of child restraint systems (CRS) and booster seats in experimental and real-world scenarios, conclusions are limited because they provide little information regarding which installation issues pose the highest risk and thus should be targeted for change. Beneficial to legislating bodies and researchers alike would be a standardized, globally relevant assessment of the potential injury risk associated with more common forms of CRS and booster seat misuse, which could be applied with observed error frequency-for example, in car seat clinics or during prototype user testing-to better identify and characterize the installation issues of greatest risk to safety. A group of 8 leading world experts in CRS and injury biomechanics, who were members of an international child safety project, estimated the potential injury severity associated with common forms of CRS and booster seat misuse. These injury risk error severity score (ESS) ratings were compiled and compared to scores from previous research that had used a similar procedure but with fewer respondents. To illustrate their application, and as part of a larger study examining CRS and booster seat labeling requirements, the new standardized ESS ratings were applied to objective installation performance data from 26 adult participants who installed a convertible (rear- vs. forward-facing) CRS and booster seat in a vehicle, and a child test dummy in the CRS and booster seat, using labels that only just met minimal regulatory requirements. The outcome measure, the risk priority number (RPN), represented the composite scores of injury risk and observed installation error frequency. Variability within the sample of ESS ratings in the present study was smaller than that generated in previous studies, indicating better agreement among experts on what constituted injury risk. Application of the new standardized ESS ratings to installation

Ergonomic Evaluation of Space Shuttle Light-Weight Seat Lever Position and Operation

Science.gov (United States)

Maida, J.; Rajulu, Sudhakar L.; Bond, Robert L. (Technical Monitor)

2000-01-01

During a Shuttle flight in the early part of 1999, one of the crewmembers was unable to operate the backrest lever for the light-weight seat in microgravity. It is essential that the crewmembers are able to adjust this back-rest lever, which is titled forward 2 degrees from vertical during launch and then moved backwards to 10 degrees aft of vertical upon reaching orbit. This adjustment is needed to cushion the crewmembers during an inadvertent crash landing situation. The original Shuttle seats, which had seat controls located on the front left and right sides of the seat, were replaced recently with the new light-weight seats. The controls for these new, seats were moved to the night side with one control at the front and the other at the back. While it was uncertain whether the problem encountered was unique to that crewmember or not it was clear to the personnel responsible for maintaining the Shuttle seats that not knowing the cause of the problem posed a safety concern for NASA. Hence the Anthropometry and Biomechanics Facility (ABF) of the Johnson Space Center was requested to perform an evaluation of the seat controls and provide NASA with appropriate recommendations on whether the seat lever positions and operations should be modified. The ABF designed an experiment to investigate the amount of pull force exerted by subjects, wearing an unpressurized or pressurized crew launch escape suit, when controls were placed in the front and back (on the right side) of the light-weight seat. Single-axis load cells were attached to the seat levers, which measured the maximum static pull forces that were exerted by the subjects. Twelve subjects, six male and six female, participated in this study. Each subject was asked to perform the pull test at least three times for each combination of lever position and suit pressure conditions. The results from this study showed that as a whole (or in general), the subjects were able to pull on the lever at the back position with

77 FR 17394 - Hazardous Materials: Approval and Communication Requirements for the Safe Transportation of Air...

Science.gov (United States)

2012-03-26

... seat-belt pretensioner devices to a capacity not greater than fifty (50) percent of the drum's total... transported; transportation operations conducted under a special permit; the potential for broad application... utilized by 31 grantees with no known safety problems. A review of the Hazardous Materials Incident Data...

Development of a Methodology to Gather Seated Anthropometry in a Microgravity Environment

Science.gov (United States)

Rajulu, Sudhakar; Young, Karen; Mesloh, Miranda

2009-01-01

The Constellation Program's Crew Exploration Vehicle (CEV) is required to accommodate the full population range of crewmembers according to the anthropometry requirements stated in the Human-Systems Integration Requirement (HSIR) document (CxP70024). Seated height is one of many critical dimensions of importance to the CEV designers in determining the optimum seat configuration in the vehicle. Changes in seated height may have a large impact to the design, accommodation, and safety of the crewmembers. Seated height can change due to elongation of the spine when crewmembers are exposed to microgravity. Spinal elongation is the straightening of the natural curvature of the spine and the expansion of inter-vertebral disks. This straightening occurs due to fluid shifts in the body and the lack of compressive forces on the spinal vertebrae. Previous studies have shown that as the natural curvature of the spine straightens, an increase in overall height of 3% of stature occurs which has been the basis of the current HSIR requirements. However due to variations in the torso/leg ratio and impact of soft tissue, data is nonexistent as to how spinal elongation specifically affects the measurement of seated height. In order to obtain this data, an experiment was designed to collect spinal elongation data while in a seated posture in microgravity. The purpose of this study was to provide quantitative data that represents the amount of change that occurs in seated height due to spinal elongation in microgravity environments. Given the schedule and budget constraints of ISS and Shuttle missions and the uniqueness of the problem, a methodology had to be developed to ensure that the seated height measurements were accurately collected. Therefore, simulated microgravity evaluations were conducted to test the methodology and procedures of the experiment. This evaluation obtained seat pan pressure and seated height data to a) ensure that the lap restraint provided sufficient

Fire resistant aircraft seat materials

Science.gov (United States)

Trabold, E. L.

1978-01-01

The establishment of a technical data base for individual seat materials in order to facilitate materials selections is reviewed. The thermal response of multi-layer constructions representative of the basic functional layers of a typical future seat is examined. These functional layers include: (1) decorative fabric cover; (2) slip sheet (topper); (3) fire blocking layer; (4) cushion reinforcement; and (5) cushioning layer. The implications for material selection for full-scale seats are discussed.

The post-traumatic biliary cyst

International Nuclear Information System (INIS)

Stellamor, K.; Hruby, W.; Stelzer, P.

1982-01-01

The case report communicated here illustrates a late complication subsequent to an emergency operation for liver rupture. This complication may result from ligating a branch of the hepatic artery to stop bleeding. If the necessary second operation is omitted for any reason, the hepatic sequester can develop into an abscess or a biliary cyst. It is to be expected that these late complications will occur more frequently in future owing to a probable increase in the incidence of the so-called blunt abdominal traumas. The reason for this is, on the one hand, the growing number of traffic accidents and, on the other hand, the increasing use of safety seat belts which tend to promote the occurrence of ruptures of the liver as part of the blunt abdominal traumas. However, we must emphasize that it is the use of safety seat belts only which ensures the traffic victims' chance of survival. (orig.) [de

Feasibility study for the development and marketing of magnesium seats for motor coaches and other modes of public transit

Energy Technology Data Exchange (ETDEWEB)

Bergeron, F. [IC-2 Technologies Inc., Quebec City, PQ (Canada); Audet, J.F. [J-F Audet Courtier Stratege, Carignan, PQ (Canada)

2004-06-01

Magnesium is currently used for seats in many minivans and luxury cars, as well as in some high speed trains. This paper addresses concerns about the use of magnesium in manufacturing seats for public transit vehicles. This paper aimed to validate the feasibility of magnesium and/or aluminum passenger seats and determine if they met weight and cost reduction objectives currently set by the public transportation industry. An assessment of the North American bus and motor coach market was made, and passenger seat design standards were reviewed. Additionally, magnesium samples were tested to ensure industry standards for material flammability and toxic fumes emissions during exposure to intense heat. Corrosion testing and a comparison with automobile industry tests were made. A number of manufacturing case studies were conducted, including life-cycle costs and comparisons with the manufacture of traditional steel seats. It was concluded that a lighter-weight seat is both technically possible and economically viable. In terms of flammability, magnesium seats met all required industry standards, and when combined with excellent seat design, increased the safety of seat occupants projected forward during collisions. In addition, magnesium's ability to absorb vibration was seen as a substantial benefit in terms of passenger comfort. In terms of manufacturing cost alone, a magnesium-aluminum hybrid was recommended. 15 refs., 25 tabs., 24 figs.

Associations between parenting styles and teen driving, safety-related behaviors and attitudes.

Science.gov (United States)

Ginsburg, Kenneth R; Durbin, Dennis R; García-España, J Felipe; Kalicka, Ewa A; Winston, Flaura K

2009-10-01

The goal was to explore the association between parenting style and driving behaviors. The 2006 National Young Driver Survey gathered data on driving safety behaviors from a nationally representative sample of 5665 ninth-, 10th-, and 11th-graders. A parenting style variable was based on adolescent reports and separated parents into 4 groups, (1) authoritative (high support and high rules/monitoring), (2) authoritarian (low support and high rules/monitoring), (3) permissive (high support and low rules/monitoring), and (4) uninvolved (low support and low rules/monitoring). Associations between parenting style and driving behaviors and attitudes were assessed. One half of parents were described as authoritative, 23% as permissive, 8% as authoritarian, and 19% as uninvolved. Compared with teens with uninvolved parents, those with authoritative parents reported one half the crash risk in the past year (odds ratio [OR]: 0.47 [95% confidence interval [CI]: 0.26-0.87]), were 71% less likely to drive when intoxicated (OR: 0.29 [95% CI: 0.19-0.44]), and were less likely to use a cellular telephone while driving (OR: 0.71 [95% CI: 0.50-0.99]). Teens with authoritative or authoritarian parents reported using seat belts nearly twice as often (authoritative: OR: 1.94 [95% CI: 1.49 -2.54]; authoritarian: OR: 1.85 [95% CI: 1.08 -3.18]) and speeding one half as often (authoritative: OR: 0.47 [95% CI: 0.36-0.61]; authoritarian: OR: 0.63 [95% CI: 0.40-0.99]) as teens with uninvolved parents. No significant differences in crash risk or seat belt use were found between permissive and uninvolved parents. Clinicians should encourage parents to set rules and to monitor teens' driving behaviors, in a supportive context.

Road safety performance indicators for the interurban road network.

Science.gov (United States)

Yannis, George; Weijermars, Wendy; Gitelman, Victoria; Vis, Martijn; Chaziris, Antonis; Papadimitriou, Eleonora; Azevedo, Carlos Lima

2013-11-01

Various road safety performance indicators (SPIs) have been proposed for different road safety research areas, mainly as regards driver behaviour (e.g. seat belt use, alcohol, drugs, etc.) and vehicles (e.g. passive safety); however, no SPIs for the road network and design have been developed. The objective of this research is the development of an SPI for the road network, to be used as a benchmark for cross-region comparisons. The developed SPI essentially makes a comparison of the existing road network to the theoretically required one, defined as one which meets some minimum requirements with respect to road safety. This paper presents a theoretical concept for the determination of this SPI as well as a translation of this theory into a practical method. Also, the method is applied in a number of pilot countries namely the Netherlands, Portugal, Greece and Israel. The results show that the SPI could be efficiently calculated in all countries, despite some differences in the data sources. In general, the calculated overall SPI scores were realistic and ranged from 81 to 94%, with the exception of Greece where the SPI was relatively lower (67%). However, the SPI should be considered as a first attempt to determine the safety level of the road network. The proposed method has some limitations and could be further improved. The paper presents directions for further research to further develop the SPI. Copyright © 2012 Elsevier Ltd. All rights reserved.

Radiation safety of the helicopter air crow-liquidators of the Chernobyl NPP accident

International Nuclear Information System (INIS)

Davydov, B.I.; Ponomarenko, V.A.; Ushakov, I.B.

1992-01-01

Three aspects of the radiation safety of the helicopter air crew who took part in the elimination of the Chernobyl NPP accident after-effects during the period from the 27-th of April to July 1986 were considered: dosimetry, physical protection and radioprotector use. 1125 subjects from the flight and engineer personnel were irradiated: 6%-2.5 mSv and more, 32%-2.1-2.5 mSv and about 60% - up to 2.0 mSv. It is stated that the use of physical protection (local screening of a pilot seat and use of special antiradiation belts) makes irradiation doe 2-3 times less. In the intense conditions of flight activity the pilots preferred the radioprotector adrenaline to cystamin. Alimentary aids in the earlier and later periods after the accident influenced favourably somatic and psychic states. 16 refs.; 1 tab

76 FR 36890 - Clarification of Prior Interpretations of the Seat Belt and Seating Requirements for General...

Science.gov (United States)

2011-06-23

... of safety greater than that which would be provided if the young children were held in the arms of... Building Ground Floor, Room W12-140, Washington, DC 20590-0001. Hand Delivery: Take comments to Docket... Administration, Office of Rulemaking, ARM-1, 800 Independence Avenue, SW., Washington, DC 20591, or by calling...

Towards Reducing the Dangers Associated with Road Traffic ...

African Journals Online (AJOL)

USER

2018-04-25

Apr 25, 2018 ... ensure drivers' personal safety and to comply with traffic regulations explain high seat belt .... which used to be the public transport fares charged for commuting in Bedford 'mummy trucks' .... females generally are risk-averse and have high-risk perception levels ... places of worship and social gatherings.

New developments of belt conveyor systems; Inclined belt systems, vertical pipe elevators, vibration belts, oscillating tubes

Energy Technology Data Exchange (ETDEWEB)

Bahke, E.A. (Universitaet Karlsruhe, Karlsruhe (Germany, F.R.). Inst. fuer Foerdertechnik)

1991-03-01

Factors that have influenced the design of belt conveyor systems are discussed - these include strength and shaping. Belt conveyor systems for inclined, steep-angle and vertical conveying are described and comparison made between cable belt and steel cord belt conveyors used in coal mines. Hose-belt or tube conveyors such as are used in the PWH/Conti-Rollgurt Conveyor System for feeding boilers in German coal fired power stations are mentioned and advantages of the pipe-belt conveyor for vertical transport discussed. Design of the vibratory conveyor for transporting solids upwards by pulses is described. 29 refs., 19 figs., 2 tabs.

Driver kinematic and muscle responses in braking events with standard and reversible pre-tensioned restraints: validation data for human models.

Science.gov (United States)

Osth, Jonas; Olafsdóttir, Jóna Marín; Davidsson, Johan; Brolin, Karin

2013-11-01

The objectives of this study are to generate validation data for human models intended for simulation of occupant kinematics in a pre-crash phase, and to evaluate the effect of an integrated safety system on driver kinematics and muscle responses. Eleven male and nine female volunteers, driving a passenger car on ordinary roads, performed maximum voluntary braking; they were also subjected to autonomous braking events with both standard and reversible pre-tensioned restraints. Kinematic data was acquired through film analysis, and surface electromyography (EMG) was recorded bilaterally for muscles in the neck, the upper extremities, and lumbar region. Maximum voluntary contractions (MVCs) were carried out in a driving posture for normalization of the EMG. Seat belt positions, interaction forces, and seat indentions were measured. During normal driving, all muscle activity was below 5% of MVC for females and 9% for males. The range of activity during steady state braking for males and females was 13-44% in the cervical and lumbar extensors, while antagonistic muscles showed a co-contraction of 2.3-19%. Seat belt pre-tension affects both the kinematic and muscle responses of drivers. In autonomous braking with standard restraints, muscle activation occurred in response to the inertial load. With pre-tensioned seat belts, EMG onset occurred earlier; between 71 ms and 176 ms after belt pre-tension. The EMG onset times decreased with repeated trials and were shorter for females than for males. With the results from this study, further improvement and validation of human models that incorporate active musculature will be made possible.

Travelers' Health: Injuries and Safety

Science.gov (United States)

... Safety Road Safety - 8 Steps MERS Health Advisory poster MERS Pictogram CDC Guide for Healthy Travel Website ... possible, fly on larger planes (>30 seats), in good weather, during the daylight hours, and with experienced ...

Intervention improves physician counseling on teen driving safety.

Science.gov (United States)

Campbell, Brendan T; Borrup, Kevin; Saleheen, Hassan; Banco, Leonard; Lapidus, Garry

2009-07-01

As part of a statewide campaign, we surveyed physician attitudes and practice regarding teen driving safety before and after a brief intervention designed to facilitate in office counseling. A 31-item self-administered survey was mailed to Connecticut physicians, and this was followed by a mailing of teen driving safety materials to physician practices in the state. A postintervention survey was mailed 8 months after the presurvey. A total of 102 physicians completed both the pre and postsurveys. Thirty-nine percent (39%) reported having had a teen in their practice die in a motor vehicle crash in the presurvey, compared with 49% in the postsurvey. Physician counseling increased significantly for a number of issues: driving while impaired from 86% to 94%; restrictions on teen driving from 53% to 64%; teen driving laws from 53% to 63%; safe vehicle from 32% to 42%; parents model safe driving from 29% to 44%; and teen-parent written contract from 15% to 37%. At baseline, the majority of physicians who provide care to teenagers in Connecticut report discussing and counseling teens on first wave teen driver safety issues (seat belts, alcohol use), but most do not discuss graduate driver licensing laws or related issues. After a brief intervention, there was a significant increase in physician counseling of teens on teen driving laws and on the use of teen-parent contracts. Additional interventions targeting physician practices can improve physician counseling to teens and their parents on issues of teen driving safety.

76 FR 53102 - Federal Motor Vehicle Safety Standards; Denial of Petition for Rulemaking; School Buses

Science.gov (United States)

2011-08-25

... small school buses to provide adequate crash protection for the occupants. For large school buses, FMVSS... and crash protection,'' requires lap/shoulder belts for all seating positions on small school buses... for adequate occupant crash protection. For large school buses, we have determined there is not a...

The Impact of Seating Location and Seating Type on Student Performance

OpenAIRE

Meeks, Michael; Knotts, Tami; James, Karen; Williams, Felice; Vassar, John; Wren, Amy

2013-01-01

While an extensive body of research exists regarding the delivery of course knowledge and material, much less attention has been paid to the performance effect of seating position within a classroom. Research findings are mixed as to whether students in the front row of a classroom outperform students in the back row. Another issue that has not been fully examined in higher education is the effect of environmental factors, specifically seating type, on student performance. This study examines...

Fire resistant aircraft seat program

Science.gov (United States)

Fewell, L. A.

1979-01-01

Foams, textiles, and thermoformable plastics were tested to determine which materials were fire retardant, and safe for aircraft passenger seats. Seat components investigated were the decorative fabric cover, slip covers, fire blocking layer, cushion reinforcement, and the cushioning layer.

Validation of seat-off and seat-on in repeated sit-to-stand movements using a single-body-fixed sensor

International Nuclear Information System (INIS)

Van Lummel, R C; Ainsworth, E; Hausdorff, J M; Lindemann, U; Beek, P J; Van Dieën, J H

2012-01-01

The identification of chair rise phases is a prerequisite for quantifying sit-to-stand movements. The aim of this study is to validate seat-off and seat-on detection using a single-body-fixed sensor against detection based on chair switches. A single sensor system with three accelerometers and three gyroscopes was fixed around the waist. Synchronized on–off switches were placed under the chair. Thirteen older adults were recruited from a residential care home and fifteen young adults were recruited among college students. Subjects were asked to complete two sets of five trials each. Six features of the trunk movement during seat-off and seat-on were calculated automatically, and a model was developed to predict the moment of seat-off and seat-on transitions. The predictions were validated with leave-one-out cross-validation. Feature extraction failed in two trials (0.7%). For the optimal combination of seat-off predictors, cross-validation yielded a mean error of 0 ms and a mean absolute error of 51 ms. For the best seat-on predictor, cross-validation yielded a mean error of –3 ms and a mean absolute error of 127 ms. The results of this study demonstrate that seat-off and seat-on in repeated sit-to-stand movements can be detected semi-automatically in young and older adults using a one-body-fixed sensor system with an accuracy of 51 and 127 ms, respectively. The use of the ambulatory instrumentation is feasible for non-technically trained personnel. This is an important step in the development of an automated method for the quantification of sit-to-stand movements in clinical practice. (paper)

Rear-facing car seat (image)

Science.gov (United States)

A rear-facing car seat position is recommended for a child who is very young. Extreme injury can occur in an accident because ... child. In a frontal crash a rear-facing car seat is best, because it cradles the head, ...

Click it or ticket evaluation, 2008–2009 : traffic tech.

Science.gov (United States)

2013-06-01

Click It or Ticket (CIOT) is a high-visibility enforcement : program to increase seat belt use. Click It or Ticket was : adopted as a national program in 2003 and is credited : with steady increases in seat belt use across the Nation. : In 2009, seat...

Evaluation of the seat fastening in the frame of a road bus submitted to frontal impact

Directory of Open Access Journals (Sweden)

Márcio Walber

Full Text Available The collective intercity transportation by bus is currently a mean of locomotion much sought after by people. Security in accidents is a very important factor that must be taken into account in design of bus body structure, being the evaluation of passenger safety of this type of vehicle is an important subject that should be checked, because in many accidents occur disconnection between seats and fastening members causing serious passengers injury, often fatal. This work aims at evaluation the behavior of frame fixing of seats of intercity bus bodies, submitted to the frontal impact situation in a rigid wall of 100% offset, through evaluation by finite element method (FEM. This study uses a numerical model corresponding to the body structure and chassis, developed through flexible beam elements, combining with shell elements for the structure of the seats and its fastening members, with the objective of not missing the essential aspects of the problem, allowing the solution with a reduced computational time. The numerical model of bus body and seat was impacted against a rigid wall at a speed of 8.89 m/s, being its validation according to the deceleration curve established by Regulation 80. Then it was gotten the Von Mises stress in fastening members of the seat structure in bus body. It is also presented a proposal to improve the fastening of the seat structure, comparing the results of the stress gotten in the two types fastening submitted to the frontal impact.

A QUESTIONNAIRE-BASED SURVEY ON ROAD VEHICLE TRAVEL HABITS OF CHILDREN WITH DISABILITIES

Directory of Open Access Journals (Sweden)

Torbjörn FALKMER

2001-01-01

Full Text Available Previous research concerning the transport situation for children with disabilities has shown a lack of reliable data on their travel habits, although such data are essential for producing rules, regulations and guidelines for safe transportation of the target group. The results from the present questionnaire study, which was carried out among 1,060 parents of children with disabilities, showed that the target group travelled frequently in the family vehicle. Most of their journeys occupied a substantial amount of time. Less than a third of all family vehicles were adapted for transporting children with disabilities. There was a large proportion of safety belt users in the family vehicle. Lack of tiedown and safety restraint system procedures meant that journeys by school transportation and Special Transport Systems were a very hazardous means of transport for children with disabilities. The results suggest that school transportation systems must be compelled to use safety belts for children with disabilities, preferably for all children, since children seated in technical aids face an even greater risk in the event of an impact than other children. Tiedown systems must be made compulsory for road vehicle transportation with technical aids used as seating systems.

Active transportation: do current traffic safety policies protect non-motorists?

Science.gov (United States)

Mader, Emily M; Zick, Cathleen D

2014-06-01

This study investigated the impact that state traffic safety regulations have on non-motorist fatality rates. Data obtained from the National Highway Traffic Safety Administration (NHTSA), the Federal Highway Administration (FHWA), and the National Institute on Alcohol Abuse and Alcoholism (NIAAA) were analyzed through a pooled time series cross-sectional model using fixed effects regression for all 50 states from 1999 to 2009. Two dependent variables were used in separate models measuring annual state non-motorist fatalities per million population, and the natural log of state non-motorist fatalities. Independent variables measuring traffic policies included state expenditures for highway law enforcement and safety per capita; driver cell phone use regulations; graduated driver license regulations; driver blood alcohol concentration regulations; bike helmet regulations; and seat belt regulations. Other control variables included percent of all vehicle miles driven that are urban and mean per capita alcohol consumption per year. Non-motorist traffic safety was positively impacted by state highway law enforcement and safety expenditures per capita, with a decrease in non-motorist fatalities occurring with increased spending. Per capita consumption of alcohol also influenced non-motorist fatalities, with higher non-motorist fatalities occurring with higher per capita consumption of alcohol. Other traffic safety covariates did not appear to have a significant impact on non-motorist fatality rates in the models. Our research suggests that increased expenditures on state highway and traffic safety and the initiation/expansion of programs targeted at curbing both driver and non-motorist intoxication are a starting point for the implementation of traffic safety policies that reduce risks for non-motorists. Copyright © 2014 Elsevier Ltd. All rights reserved.

Infant bath seats, drowning and near-drowning.

Science.gov (United States)

Byard, R W; Donald, T

2004-01-01

To investigate the possible role of infant bathtub seats in drowning and near-drowning episodes in infants. A review was conducted of the files of the Forensic Science Centre and Child Protection Unit, Women's and Children's Hospital, Adelaide, South Australia, for significant immersion incidents in infants involving bathtub seats from January 1998 to December 2003. A total of six cases of drowning occurred over the 6-year period of the study in children under 2 years of age, including two infants. One of these cases, a 7-month-old boy, had been left unattended for some time in an adult bath in a bathtub seat. He was found drowned, having submerged after slipping down and becoming trapped in the seat. Three near-drowning episodes occurred in children under the age of 2 years, including two boys aged 7 and 8 months, both of whom had been left for some time in adult baths in bath seats. Both were successfully resuscitated and treated in hospital. These cases demonstrate the vulnerability of infants to immersion incidents when left unattended in bathtubs. Bathtubs are particularly dangerous for infants as the slippery and smooth surfaces predispose to loss of balance and make escape from water difficult. Infant bathtub seats may give parents and child carers a false sense of security leading to infants being left unattended. Unfortunately, however, infants may fall out of, or slip and become trapped in, such seats. Infants and young children cannot be left unsupervised in water, and devices used as bathing aids such as bathtub seats may contribute to immersion incidents.

30 CFR 75.1731 - Maintenance of belt conveyors and belt conveyor entries.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Maintenance of belt conveyors and belt conveyor....1731 Maintenance of belt conveyors and belt conveyor entries. (a) Damaged rollers, or other damaged belt conveyor components, which pose a fire hazard must be immediately repaired or replaced. All other...

Lap belts and three-point belts.

NARCIS (Netherlands)

Kampen, L.T.B. van & Edelman, A.

1975-01-01

Results of the swov-accident investigation prove that if there are any differences in the effectiveness of lap belts and three-point belts, these are so small that they cannot form a basis for giving preference to one type over the other. Furthermore, in spite of the results of this investigation

Simulation of engine auxiliary drive V-belt slip motion. Part 1. Development of belt slip model; Engine hoki V belt slip kyodo no simulation. 1. Belt slip model no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kurisu, T [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

V-belts are widely used for driving auxiliary components of an engine. Inadequet design of such belt system sometimes results in troubles such as belt squeak, side rubber separation and/or bottom rubber crack. However, there has been no design tools which can predict belt slip quantitatively. The author developed a motion simulation program of Auxiliary Drive V-Belt System considering belt slip. The program showed good prediction accuracy for belt slip motion. This paper describes the simulation model. 1 ref., 12 figs.

Who is in control of road safety? A STAMP control structure analysis of the road transport system in Queensland, Australia.

Science.gov (United States)

Salmon, Paul M; Read, Gemma J M; Stevens, Nicholas J

2016-11-01

Despite significant progress, road trauma continues to represent a global safety issue. In Queensland (Qld), Australia, there is currently a focus on preventing the 'fatal five' behaviours underpinning road trauma (drug and drink driving, distraction, seat belt wearing, speeding, and fatigue), along with an emphasis on a shared responsibility for road safety that spans road users, vehicle manufacturers, designers, policy makers etc. The aim of this article is to clarify who shares the responsibility for road safety in Qld and to determine what control measures are enacted to prevent the fatal five behaviours. This is achieved through the presentation of a control structure model that depicts the actors and organisations within the Qld road transport system along with the control and feedback relationships that exist between them. Validated through a Delphi study, the model shows a diverse set of actors and organisations who share the responsibility for road safety that goes beyond those discussed in road safety policies and strategies. The analysis also shows that, compared to other safety critical domains, there are less formal control structures in road transport and that opportunities exist to add new controls and strengthen existing ones. Relationships that influence rather than control are also prominent. Finally, when compared to other safety critical domains, the strength of road safety controls is brought into question. Copyright © 2016 Elsevier Ltd. All rights reserved.

14 CFR 135.113 - Passenger occupancy of pilot seat.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Passenger occupancy of pilot seat. 135.113... Operations § 135.113 Passenger occupancy of pilot seat. No certificate holder may operate an aircraft type certificated after October 15, 1971, that has a passenger seating configuration, excluding any pilot seat, of...

Belt Aligning Revisited

Directory of Open Access Journals (Sweden)

Yurchenko Vadim

2017-01-01

parts of the conveyor, the sides of the belt wear intensively. This results in reducing the life of the belt. The reasons for this phenomenon are well investigated, but the difficulty lies in the fact that they all act simultaneously. The belt misalignment prevention can be carried out in two ways: by minimizing the effect of causes and by aligning the belt. The construction of aligning devices and errors encountered in practice are considered in this paper. Self-aligning roller supports rotational in plan view are recommended as a means of combating the belt misalignment.

Condition-Based Conveyor Belt Replacement Strategy in Lignite Mines with Random Belt Deterioration

Science.gov (United States)

Blazej, Ryszard; Jurdziak, Leszek

2017-12-01

In Polish lignite surface mines, condition-based belt replacement strategies are applied in order to assure profitable refurbishment of worn out belts performed by external firms specializing in belt maintenance. In two of three lignite mines, staff asses belt condition subjectively during visual inspections. Only one mine applies specialized diagnostic device (HRDS) allowing objective magnetic evaluation of belt core condition in order to choose the most profitable moment for the dismantling of worn out belt segments from conveyors and sending them to the maintenance firm which provides their refurbishment. This article describes the advantages of a new diagnostic device called DiagBelt. It was developed at the Faculty of Geoengineering, Mining and Geology, Wroclaw University of Science and Technology. Economic gains from its application are calculated for the lignite mine and for the belt maintenance firm, taking into account random life (durability) of new and reconditioned belts (after the 1st and the 2nd refurbishment). Recursive calculations for following years allow the estimation of the length and costs of replaced, reconditioned and purchased belts on an annual basis, while the use of the Monte Carlo method allows the estimation of their variability caused by random deterioration of belts. Savings are obtained due to better selection of moments (times) for the replacement of belt segments and die to the possibility to qualify worn out belts for refurbishment without the need to remove their covers. In effect, increased belt durability and lowered share of waste belts (which were not qualified for reconditioning) create savings which can quickly cover expenditures on new diagnostic tools and regular belt inspections in the mine.

Development of electrostatic charging evaluation equipment for automobile seat; Jidoshayo seat no taidensei shiken hyoka sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Maeda, K [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

When passengers get out of vehicle, electrostatics is generated by separation of seat cloth and passenger cloth, and then charged to passenger`s body. It has been impossible for us to simulate this induction charging phenomenon with current evaluation equipments. We developed a new seat cloth evaluation equipments using induction charging plate, which enables us to simulate the phenomenon. This paper describes this new electrostatic charging evaluation method for automobile seat cloth. 5 refs., 6 figs.

77 FR 22386 - Hyundai Motor Company, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2012-04-13

... in S4.1.5.5.2, each passenger car shall have a Type 2 seat belt assembly that conforms to Standard No...-facing designated seating positions shall have a Type 1 or Type 2 seat belt assembly that conforms to... be a key or key-like object. Summary of Hyundai's Analysis and Arguments Hyundai believes that the...

78 FR 38444 - Hyundai Motor Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-06-26

... provided in Sec. 4.1.5.5.2, each passenger car shall have a Type 2 seat belt assembly that conforms to..., except that side-facing designated seating positions shall have a Type 1 or Type 2 seat belt assembly... arguments, Hyundai Motor Company does not believe that it is appropriate to conduct a recall campaign to...

Conceptual design of a Moving Belt Radiator (MBR) shuttle-attached experiment

Science.gov (United States)

Aguilar, Jerry L.

1990-01-01

The conceptual design of a shuttle-attached Moving Belt Radiator (MBR) experiment is presented. The MBR is an advanced radiator concept in which a rotating belt is used to radiate thermal energy to space. The experiment is developed with the primary focus being the verification of the dynamic characteristics of a rotating belt with a secondary objective of proving the thermal and sealing aspects in a reduced gravity, vacuum environment. The mechanical design, selection of the belt material and working fluid, a preliminary test plan, and program plan are presented. The strategy used for selecting the basic sizes and materials of the components are discussed. Shuttle and crew member requirements are presented with some options for increasing or decreasing the demands on the STS. An STS carrier and the criteria used in the selection process are presented. The proposed carrier for the Moving Belt Radiator experiment is the Hitchhiker-M. Safety issues are also listed with possible results. This experiment is designed so that a belt can be deployed, run at steady state conditions, run with dynamic perturbations imposed, verify the operation of the interface heat exchanger and seals, and finally be retracted into a stowed position for transport back to earth.

SEAT CHOICE AND DISTANCE JUDGMENT IN PUBLIC SPACES (1).

Science.gov (United States)

Neto, Olavo Avalone; Munakata, Jun

2015-10-01

This research assessed whether public space users will adopt a least-effort approach and choose a less suitable seat nearby or seek the most suitable seat, even if it is farther away from them when the decision is made. How distance assessment affects seat choice was investigated through an observational survey, which allowed the identification of behavioral patterns. Those behavioral patterns were then tested in a paired comparison experiment with 40 participants. The results showed that the effect of distance on seat choice is related to the difference in distance between the options and that a sufficient difference can cause trade-offs between distance and seat properties. The necessary difference in distance is conditioned by the activity and the seat properties.

75 FR 36062 - Availability of Conservation Seat and Diving Operations Seat for the Flower Garden Banks National...

Science.gov (United States)

2010-06-24

... Conservation Seat and Diving Operations Seat for the Flower Garden Banks National Marine Sanctuary Advisory... Flower Garden Banks National Marine Sanctuary Advisory Council: Conservation and Diving Operations... Jennifer Morgan, NOAA--Flower Garden Banks National Marine Sanctuary, 4700 Avenue U, Bldg. 216, Galveston...

Evolution of the stress fields in the Zagros Foreland Folded Belt using focal mechanisms and kinematic analyses: the case of the Fars salient, Iran

Science.gov (United States)

Sarkarinejad, Khalil; Zafarmand, Bahareh; Oveisi, Behnam

2018-03-01

The NW-SE trending Zagros orogenic belt was initiated during the convergence of the Afro-Arabian continent and the Iranian microcontinent in the Late Cretaceous. Ongoing convergence is confirmed by intense seismicity related to compressional stresses collision-related in the Zagros orogenic belt by reactivation of an early extensional faulting to latter compressional segmented strike-slip and dip-slip faulting. These activities are strongly related either to the deep-seated basement fault activities (deep-seated earthquakes) underlies the sedimentary cover or gently dipping shallow-seated décollement horizon of the rheological weak rocks of the infra-Cambrian Hormuz salt. The compressional stress regimes in the different units play an important role in controlling the stress conditions between the different units within the sedimentary cover and basement. A significant set of nearly N-S trending right-lateral strike-slip faults exists throughout the study area in the Fars area in the Zagros Foreland Folded Belt. Fault-slip and focal mechanism data were analyzed using the stress inversion method to reconstruct the paleo and recent stress conditions. The results suggest that the current direction of maximum principal stress averages N19°E, with N38°E that for the past from Cretaceous to Tertiary (although a few sites on the Kar-e-Bass fault yield a different direction). The results are consistent with the collision of the Afro-Arabian continent and the Iranian microcontinent. The difference between the current and paleo-stress directions indicates an anticlockwise rotation in the maximum principle stress direction over time. This difference resulted from changes in the continental convergence path, but was also influenced by the local structural evolution, including the lateral propagation of folds and the presence of several local décollement horizons that facilitated decoupling of the deformation between the basement and the sedimentary cover. The obliquity of

Localization techniques in resection of deep seated cavernous angiomas - review and reevaluation of frame based stereotactic approaches.

Science.gov (United States)

Slotty, P J; Ewelt, C; Sarikaya-Seiwert, S; Steiger, H-J; Vesper, J; Hänggi, D

2013-04-01

Providing high accuracy is crucial in neurosurgery especially for resection of deep seated small cerebral pathologies such as cavernous angiomas. The goal of the present series was to reevaluate the feasibility, accuracy, efficacy and safety of frame-based, stereotactically guided resection for patients suffering from small deep-seated cavernous angiomas. Additionally a review of the literature on navigational tools in cavernoma surgery is provided comparing different navigation strategies. Ten patients with deep-seated, small intracranial, cavernous angiomas being subject to frame-based, stereotactically aided resection are included in this survey. Based on the stereotactic-fused image, set entry and target point aimed at the rim of the cavernoma were calculated. A minicraniotomy (Assets and drawbacks of the stereotactic-aided approach were evaluated, patients were analyzed for surgery-related neurological deficits and completeness of resection. Complete resection was achieved in all ten patients verified by post-surgery MRI imaging. The surgical procedure itself was only slightly aggravated by the stereotactic equipment. No adverse events such as bleedings or infections were observed in our series. Stereotactically guided, minimally invasive resection of deep seated and small cavernous angiomas is accurate and effective. The frame-based stereotactic guidance requires some additional time and effort which seems justified only for deep seated and small cavernous angiomas. Frameless neuronavigation is a common tool in cavernoma surgery and its spatial resolution is sufficient for the majority of cases.

Exploring the design of a lightweight, sustainable and comfortable aircraft seat.

Science.gov (United States)

Kokorikou, A; Vink, P; de Pauw, I C; Braca, A

2016-07-19

Making a lightweight seat that is also comfortable can be contradictory because usually comfort improvement means adding a feature (e.g. headrest, adjustable lumbar support, movable armrests, integrated massage systems, etc.), which makes seats heavier. This paper explores the design of an economy class aircraft seat that aims to be lightweight, comfortable and sustainable. Theory about comfort in seats, ergonomics, lightweight design, Biomimicry and Cradle to cradle was studied and resulted in a list of requirements that the new seat should satisfy. The design process resulted in a new seat that is 36% lighter than the reference seat, which showed that a significant weight reduction can be achieved. This was completed by re-designing the backrest and seat pan and integrating their functions into a reduced number of parts. Apart from the weight reduction that helps in reducing the airplane's environmental impact, the seat also satisfies most of the other sustainability requirements such as the use of recyclable materials, design for disassembly, easy to repair. A user test compared the new seat with a premium economy class aircraft seat and the level of comfort was similar. Strong points of the new design were identified such as the lumbar support and the cushioning material, as well as shortcomings on which the seat needs to be improved, like the seat pan length and the first impression. Long term comfort tests are still needed as the seat is meant for long-haul flights.

Deep-seated sarcomas of the penis

Directory of Open Access Journals (Sweden)

Alberto A. Antunes

2005-06-01

Full Text Available Mesenchymal neoplasias represent 5% of tumors affecting the penis. Due to the rarity of such tumors, there is no agreement concerning the best method for staging and managing these patients. Sarcomas of the penis can be classified as deep-seated if they derive from the structures forming the spongy body and the cavernous bodies. Superficial lesions are usually low-grade and show a small tendency towards distant metastasis. In contrast, deep-seated lesions usually show behavior that is more aggressive and have poorer prognosis. The authors report 3 cases of deep-seated primary sarcomas of the penis and review the literature on this rare and aggressive neoplasia.

Support force measures of midsized men in seated positions.

Science.gov (United States)

Bush, Tamara Reid; Hubbard, Robert P

2007-02-01

Two areas not well researched in the field of seating mechanics are the distribution of normal and shear forces, and how those forces change with seat position. The availability of these data would be beneficial for the design and development of office, automotive and medical seats. To increase our knowledge in the area of seating mechanics, this study sought to measure the normal and shear loads applied to segmental supports in 12 seated positions, utilizing three inclination angles and four levels of seat back articulation that were associated with automotive driving positions. Force data from six regions, including the thorax, sacral region, buttocks, thighs, feet, and hand support were gathered using multi-axis load cells. The sample contained 23 midsized subjects with an average weight of 76.7 kg and a standard deviation of 4.2 kg, and an average height of 1745 mm with a standard deviation of 19 mm. Results were examined in terms of seat back inclination and in terms of torso articulation for relationships between seat positions and support forces. Using a repeated measures analysis, significant differences (p<0.05) were identified for normal forces relative to all inclination angles except for forces occurring at the hand support. Other significant differences were observed between normal forces behind the buttocks, pelvis, and feet for torso articulations. Significant differences in the shear forces occurred under the buttocks and posterior pelvis during changes in seat back inclination. Significant differences in shear forces were also identified for torso articulations. These data suggest that as seat back inclination or torso articulation change, significant shifts in force distribution occur.

Storm-time radiation belt electron dynamics: Repeatability in the outer radiation belt

Science.gov (United States)

Murphy, K. R.; Mann, I. R.; Rae, J.; Watt, C.; Boyd, A. J.; Turner, D. L.; Claudepierre, S. G.; Baker, D. N.; Spence, H. E.; Reeves, G. D.; Blake, J. B.; Fennell, J. F.

2017-12-01

During intervals of enhanced solar wind driving the outer radiation belt becomes extremely dynamic leading to geomagnetic storms. During these storms the flux of energetic electrons can vary by over 4 orders of magnitude. Despite recent advances in understanding the nature of competing storm-time electron loss and acceleration processes the dynamic behavior of the outer radiation belt remains poorly understood; the outer radiation belt can exhibit either no change, an enhancement, or depletion in radiation belt electrons. Using a new analysis of the total radiation belt electron content, calculated from the Van Allen probes phase space density (PSD), we statistically analyze the time-dependent and global response of the outer radiation belt during storms. We demonstrate that by removing adiabatic effects there is a clear and repeatable sequence of events in storm-time radiation belt electron dynamics. Namely, the relativistic (μ=1000 MeV/G) and ultra-relativistic (μ=4000 MeV/G) electron populations can be separated into two phases; an initial phase dominated by loss followed by a second phase dominated by acceleration. At lower energies, the radiation belt seed population of electrons (μ=150 MeV/G) shows no evidence of loss but rather a net enhancement during storms. Further, we investigate the dependence of electron dynamics as a function of the second adiabatic invariant, K. These results demonstrate a global coherency in the dynamics of the source, relativistic and ultra-relativistic electron populations as function of the second adiabatic invariant K. This analysis demonstrates two key aspects of storm-time radiation belt electron dynamics. First, the radiation belt responds repeatably to solar wind driving during geomagnetic storms. Second, the response of the radiation belt is energy dependent, relativistic electrons behaving differently than lower energy seed electrons. These results have important implications in radiation belt research. In particular

Belt attachment and system

Energy Technology Data Exchange (ETDEWEB)

Schneider, Abraham D.; Davidson, Erick M.

2018-03-06

Disclosed herein is a belt assembly including a flexible belt with an improved belt attachment. The belt attachment includes two crossbars spaced along the length of the belt. The crossbars retain bearings that allow predetermined movement in six degrees of freedom. The crossbars are connected by a rigid body that attaches to the bearings. Implements that are attached to the rigid body are simply supported but restrained in pitching rotation.

Time to death analysis of road traffic accidents in relation to delta V, drunk driving, and restraint systems.

Science.gov (United States)

Ju, Yonghan; Sohn, So Young

2014-01-01

The main goal of this research is to identify variables related to the expected time to death due to road traffic accidents (RTAs). Such research is expected to be useful in improving safety laws and regulations and developing new safety systems. The resulting information is crucial not only for reducing accident fatalities but for assessing related insurance policies. In this article, we analyze factors that are potentially associated with variation in the expected survival time after a road traffic accident using Weibull regression. In particular, we consider the association with alcohol involvement, delta V, and restraint systems. Our empirical results, obtained based on the NASS-CDS, indicate that the expected survival time for non-alcohol-impaired drivers is 3.23 times longer at a delta V of 50 km/h than that for alcohol-impaired drivers under the same conditions. In addition, it was observed that, even when occupants were alcohol-impaired, if they were protected by both air bags and seat belts, their expected survival time after an RTA increased 2.59-fold compared to alcohol-impaired drivers who used only seat belts. Our findings may be useful in improving road traffic safety and insurance policies by offering insights into the factors that reduce fatalities.

Elderly road collision injury outcomes associated with seat positions and seatbelt use in a rapidly aging society-A case study in South Korea.

Directory of Open Access Journals (Sweden)

Yuna Noh

Full Text Available Aging has long been regarded as one of the most critical factors affecting crash injury outcomes. In South Korea, where the elderly population is projected to reach 35.9% by 2050, the implications of an increasing number of elderly vehicle users on road safety are evident. In this research, the confounding effect of occupant age in a vehicle in terms of seat position and seatbelt use was investigated. In addition, elderly occupants were divided into a younger-old group aged between 65 and 74 years and an older-old group aged 75 years and older in an effort to assess whether the conventional elderly age standard of 65 years should be reconsidered.A multinomial logit framework was adopted to predict two-level injury severity using collision data between 2008 and 2015. Predictor variables included gender, age group, seat position, seatbelt, road type, road slope, road surface, road line, and type of vehicle. Five models, a base model with no interactions and four interaction models which were combinations of age group, seatbelt use and seat position, were devised and evaluated.With no interacting term, age was the most prominent predictor. Elderly occupants were most likely to suffer from severe injury without a seatbelt in all seat positions, and the use of a seatbelt reduced this likelihood the most in the elderly group as well. Front passenger seats had the highest risk to elderly occupants, while the driver seat was statistically insignificant. When the elderly group was divided into the younger-old group and the older-old group, the older-olds were found to be much more vulnerable compared to the younger-olds. In particular, older drivers were five times more likely to suffer a severe injury without a seatbelt.The degree of injury severity of elderly occupants was reduced the most with the use of a seatbelt, demonstrating the importance of using seat restraints. The sharp increase in the risk of injury of the older-old group suggests that the

Elderly road collision injury outcomes associated with seat positions and seatbelt use in a rapidly aging society-A case study in South Korea.

Science.gov (United States)

Noh, Yuna; Yoon, Yoonjin

2017-01-01

Aging has long been regarded as one of the most critical factors affecting crash injury outcomes. In South Korea, where the elderly population is projected to reach 35.9% by 2050, the implications of an increasing number of elderly vehicle users on road safety are evident. In this research, the confounding effect of occupant age in a vehicle in terms of seat position and seatbelt use was investigated. In addition, elderly occupants were divided into a younger-old group aged between 65 and 74 years and an older-old group aged 75 years and older in an effort to assess whether the conventional elderly age standard of 65 years should be reconsidered. A multinomial logit framework was adopted to predict two-level injury severity using collision data between 2008 and 2015. Predictor variables included gender, age group, seat position, seatbelt, road type, road slope, road surface, road line, and type of vehicle. Five models, a base model with no interactions and four interaction models which were combinations of age group, seatbelt use and seat position, were devised and evaluated. With no interacting term, age was the most prominent predictor. Elderly occupants were most likely to suffer from severe injury without a seatbelt in all seat positions, and the use of a seatbelt reduced this likelihood the most in the elderly group as well. Front passenger seats had the highest risk to elderly occupants, while the driver seat was statistically insignificant. When the elderly group was divided into the younger-old group and the older-old group, the older-olds were found to be much more vulnerable compared to the younger-olds. In particular, older drivers were five times more likely to suffer a severe injury without a seatbelt. The degree of injury severity of elderly occupants was reduced the most with the use of a seatbelt, demonstrating the importance of using seat restraints. The sharp increase in the risk of injury of the older-old group suggests that the age standard of

Civil aircraft side-facing seat research summary.

Science.gov (United States)

2012-11-01

The Federal Aviation Administration (FAA) has standards and regulations that are intended to protect aircraft : occupants in the event of a crash. However, side-facing seats were not specifically addressed when aircraft seat : dynamic test standards ...

25 CFR 170.144 - What are eligible highway safety projects?

Science.gov (United States)

2010-04-01

... RESERVATION ROADS PROGRAM Indian Reservation Roads Program Policy and Eligibility Highway Safety Functions... management system; (g) Education and outreach highway safety programs, such as use of child safety seats... 25 Indians 1 2010-04-01 2010-04-01 false What are eligible highway safety projects? 170.144...

Technical note: Spine loading in automotive seating

NARCIS (Netherlands)

Zenk, R.; Franz, M.; Bubb, H.; Vink, P.

2012-01-01

For car manufacturers, seat comfort is becoming more important in distinguishing themselves from their competitors. Therefore, many studies on participative seat comfort are carried out. In this paper, an objective assessment approach is reported which evaluates the concept of "optimal load

Riding the belt

Energy Technology Data Exchange (ETDEWEB)

Potts, A

1998-04-01

Recent developments in conveyor systems have focused on accessories rather than the belt itself. Radio frequency identification (RFID) is a technology using transponders embedded in conveyor belts and this is the latest development at the German firm Contitech. The system described in the articles developed with Moers, features transponders for cooling, controlling and monitoring conveyor belts. Other developments mentioned include a JOKI drum motor featuring a fully integrated gearbox and electric motor enclosed in a steel shell, from Interoll; a new scraper cleaning system from Hosch, new steel cord belting from Fenner, a conveying system for Schleenhain lignite opencast mine by FAM Foerdelantigen Magdeburg; new bearings from Nadella (the sales arm of Intersoll-Rand), an anti-shock belt transfer table from Rosta and new caliper disc brakes from GE Industrial.

49 CFR 571.207 - Standard No. 207; Seating systems.

Science.gov (United States)

2010-10-01

... standard establishes requirements for seats, their attachment assemblies, and their installation to....2. General performance requirements. When tested in accordance with S5, each occupant seat shall... than a school bus; a passenger seat on a school bus with a GVWR greater than 4,536 kilograms (10,000...

Automation of belts; Automatizacion de Cintas de Interior

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

This document presents the most important aspects, and the results of the project DEVELOPMENT AND COMMISSIONING OF AN INTEGRATED HAULAGE AND VENTILATION CONTROL SYSTEM IN A MINE USING VERY LONG SUBLEVEL-CAVING WINNING METHOD. Project's targets were to develop, implement and commission a distributed control system for underground mining, which should allow the control and optimisation of the whole (continuous) haulage network. It should also integrate statutory safety features required for both winning and haulage. The system is capable of controlling the most common devices used in underground coal mining transport networks, like conveyor belts, armored conveyors, regulation silos, etc. from the winning faces to the surface, and also the interlocks between them. Moreover, the system implements statutory safety functions for conveyor belt operation, and for mining activities carried out in culls de sac. Specifically, for its relationship with the transport system, it should monitor secondary ventilation, fire damp and toxic gases concentration, and mains power presence in the culls de sac, which have already reached a length of 2000 m. The prototype was installed in the mine that Carbones de Pedraforca owns in Saldes, Barcelona. (Author)

Active Suspension of Truck Seat

Directory of Open Access Journals (Sweden)

Masaaki Kawana

1998-01-01

Full Text Available The driver’s seat of a heavy duty truck is usually mounted on a spring–damper assembly anchored to the cab floor. To improve riding comfort, this study investigated the effects of mounting a computer-controlled actuator in parallel with the traditional spring–damper assembly. A dynamic model of the seat is represented by a two degree-of-freedom system, including a cushion. In this paper, a control system is designed, using optimal control theory, which minimizes rms vertical acceleration at a point representing the driver’s hip point. In this system, accelerations of the hip point, the seat frame and the cab floor are picked up and integrated to obtain the state variables to be fed back and fed forward to the actuator through a digital computer. The actuator is constructed with electric servo-motor and ball-screw mechanism. The experimental study was carried out on a shaker, which simulates the vibrations of the cab floor in actual service. Results were obtained for both a dummy and a real human body. The vibration test produced rms accelerations of the seat and the hip point of about 1.0 m/s2 without the actuator, while the rms accelerations were suppressed to about 0.5 m/s2 at a rms input voltage to the servo-motor of 1.0 V.

Trend analysis of incidents involving setpoint drift in safety or safety/relief valves at U.S. LWRs

International Nuclear Information System (INIS)

Watanabe, Norio

2008-01-01

Since the beginning of the 1980's, in the United States, there have been many licensee event reports (LERs) involving setpoint drift in safety or safety/relief valves. The United States Nuclear Regulatory Commission (NRC) has issued a lot of generic communications on this issue and the industry has made efforts to resolve the issue. However, the NRC staff recently highlighted that over 70 LERs involved instances where safety or safety/relief valves failed to meet the allowed setpoint tolerance from 2001 through August 2006. In the present study, we analyzed the U.S. experience with setpoint drift in safety/relief valves (SRVs) at BWRs, pressurizer safety valves (PSVs), and main steam safety valves (MSSVs) at PWRs by reviewing approximately 90 LERs from 2000 to 2006 and examined the trend focusing on causes and setpoint deviation ranges. This study indicates that for SRVs and MSSVs, disc-seat bonding is a dominant cause of the setpoint drifting high and has a tendency to result in a relatively large deviation of the setpoint. This means that disc-seat bonding might be a safety concern from the view point of overpressure protection. For PSVs, the deviation of setpoints is generally small, although its causes are not specified in many instances. (author)

Tribal motor vehicle injury prevention programs for reducing disparities in motor vehicle-related injuries.

Science.gov (United States)

West, Bethany A; Naumann, Rebecca B

2014-04-18

A previous analysis of National Vital Statistics System data for 2003-2007 that examined disparities in rates of motor vehicle-related death by race/ethnicity and sex found that death rates for American Indians/Alaska Natives were two to four times the rates of other races/ethnicities. To address the disparity in motor vehicle-related injuries and deaths among American Indians/Alaska Natives, CDC funded four American Indian tribes during 2004-2009 to tailor, implement, and evaluate evidence-based road safety interventions. During the implementation of these four motor vehicle-related injury prevention pilot programs, seat belt and child safety seat use increased and alcohol-impaired driving decreased. Four American Indian/Alaska Native tribal communities-the Tohono O'odham Nation, the Ho-Chunk Nation, the White Mountain Apache Tribe, and the San Carlos Apache Tribe-implemented evidence-based road safety interventions to reduce motor vehicle-related injuries and deaths. Each community selected interventions from the Guide to Community Preventive Services and implemented them during 2004-2009. Furthermore, each community took a multifaceted approach by incorporating several strategies, such as school and community education programs, media campaigns, and collaborations with law enforcement officers into their programs. Police data and direct observational surveys were the main data sources used to assess results of the programs. Results included increased use of seat belts and child safety seats, increased enforcement of alcohol-impaired driving laws, and decreased motor vehicle crashes involving injuries or deaths. CDC's Office of Minority Health and Health Equity selected the intervention analysis and discussion as an example of a program that might be effective for reducing motor vehicle-related injury disparities in the United States. The Guide to Community Preventive Services recognizes these selected interventions as effective; this report examines the

A target fibre study on seats in public houses.

Science.gov (United States)

Kelly, E; Griffin, R M

1998-01-01

A target fibre survey was conducted to assess the random occurrence of a blue wool fibre on seats in public houses throughout the United Kingdom. Fibre tape lifts were taken from 80 seats. Four seats yielded matching fibres and five of these were found on one seat. A total of 292 fibres were identified; nine fibres proved indistinguishable from the target after comparison microscopy, microspectro-photometry and attempts at thin layer chromatography, and two of these fibres were still apparently indistinguishable after TLC analysis although only one dye component was visible.

Cross-sectional study of road accidents and related law enforcement efficiency for 10 countries: A gap coherence analysis.

Science.gov (United States)

Urie, Yohan; Velaga, Nagendra R; Maji, Avijit

2016-10-02

Road crashes are considered as the eighth leading causes of death. There is a wide disparity in crash severity and law enforcement efficiency among low-, medium-, and high-income countries. It would be helpful to review the crash severity trends in these countries, identify the vulnerable road users, and understand the law enforcement effectiveness in devising efficient road safety improvement strategies. The crash severity, fatality rate among various age groups, and law enforcement strategies of 10 countries representing low-income (i.e., India and Morocco), medium-income (i.e. Argentina, South Korea, and Greece), and high-income (i.e., Australia, Canada, France, the UK, and the United States) are studied and compared for a period of 5 years (i.e., 2008 to 2012). The critical parameters affecting road safety are identified and correlated with education, culture, and basic compliance with traffic safety laws. In the process, possible road safety improvement strategies are identified for low-income countries. The number of registered vehicles shows an increasing trend for low-income countries as do the crash rate and crash severity. Compliance related to seat belt and helmet laws is high in high-income countries. In addition, recent seat belt- and helmet-related safety programs in middle-income countries helped to curb fatalities. Noncompliance with safety laws in low-income countries is attributed to education, culture, and inefficient law enforcement. Efficient law enforcement and effective safety education taking into account cultural diversity are the key aspects to reduce traffic-related injuries and fatalities in low-income countries like India.

The Study of Fabric Performance for Car Seats

Directory of Open Access Journals (Sweden)

Antonin Havelka

2017-09-01

Full Text Available This paper deals with the investigation of the performance of car seat fabrics in terms of physiological comfort of sitting, specifi cally their water vapour resistance and air permeability. The current work presents an alternative approach to increasing the effectiveness of car seat fabrics through a combination of newly designed middle layer with forced convection achieved by a supplementary suction ventilation device. The supplementary device was designed to measure water vapour permeability by means of the sweating guarded hot plate (SGHP system. It consists of two parts: a frame to grip a tested sample for measurements within the SGHP system and two suction ventilators which are arranged at one end of the mentioned frame in order to provide suction into the tested fabric plane during the SGHP test. The results of this investigation show that water vapour transport is increased by approximately 20% compared to the standard way of measurement by means of SGHP because of forced air flow in the plane of ribbed – channelled structure of the car seat middle layer. The findings of this study have a number of important implications for future practice. The combination of a car seat cover with channelled structure and forced air fl ow improves physiological comfort of sitting which is a key issue for both drivers and manufacturers. The suggested device for forced air flow convection in the plane of a car seat fabric has not yet been part of an actual car seat, however it is possible to use its principles in a smart car seat prototype.

Attempting to train a digital human model to reproduce human subject reach capabilities in an ejection seat aircraft

NARCIS (Netherlands)

Zehner, G.F.; Hudson, J.A.; Oudenhuijzen, A.

2006-01-01

From 1997 through 2002, the Air Force Research Lab and TNO Defence, Security and Safety (Business Unit Human Factors) were involved in a series of tests to quantify the accuracy of five Human Modeling Systems (HMSs) in determining accommodation limits of ejection seat aircraft. The results of these

Test tools of physics radiography children as a support for safety radiation and safety patients

International Nuclear Information System (INIS)

Siti Masrochah; Yeti Kartikasari; Ardi Soesilo Wibowo

2013-01-01

Radiographic examination of the thorax children aged 1-3 years have a high sufficiently failure. This failure is caused by the movement and difficulty positioning the patient, resulting in the risk of repeat radiographs to patient safety particularly unnecessary radiation risks. It is therefore necessary to develop research on children design fixation devices. This research aims to create a design tool fixation on radiographs children to support radiation safety and patient safety. This research is a descriptive exploratory approach to tool design. The independent variables were the design tools, variable tool function test results, and radiographic variables controlled thorax. The procedure is done by designing data collection tools, further trials with 20 samples. Processing and analysis of data is done by calculating the performance assessment tool scores with range 1-3. The results showed that the design tool of fixation in the form of standard radiographic cassette equipped with chairs and some form of seat belt fixation. The procedure uses a tool fixation is routine radiographic follow thorax child in an upright position. Function test results aids fixation is to have an average score of 2.66, which means good. While the test results for each component, the majority of respondents stated that the reliability of the device is quite good with a score of 2.45 (60 %), convenience tool with a score of 2.60 (70 %), quality of the radiographs did not incontinence of the thorax radiograph with a score 2.55 (85 %), the child protection (security) with a score of 2.70 (70 %), good design aesthetic design with a score of 2.80 (80 %), addition of radiation from the others on the use of these tools do not need with a score of 2.80 (80 %), and there is no additional radiation due to repetitions with a score of 2.85 (90 %). (author)

Optimization of Aircraft Seat Cushion Fire Blocking Layers.

Science.gov (United States)

1983-03-01

function of cost and weight, and the costs of labor involved in assembling a ccmposite seat cushion. The same classes of high char yield polymers that are...SEAT LATER DESIGN REPORT NRBBNBsg$$$$$$NN$$R$$$$$ SEAT DESIGN NUMBER: 009 LAYER NAME CODE NO. S MANUFACTURER 5 COST FACTORS . LABOR ...72621, 9096.. 7SS43. 73757. 77147. DELTA COSTS 0. 8340. 2922. 1136. 4327. ACOSOS in Iho..aS Of dollars. COST SUIRNY REPORT Re ....... VONR3 MORFA

Earth's radiation belts

International Nuclear Information System (INIS)

Moslehi Fard, M.

1984-01-01

The theory of trapped particles in a magnetic field of approximated dipole is described completely in the first part. Second part contains experimental results. The mechanism of radiation belt source ''albedo neutrons'' and also types of dissipation mechanism about radiation belt is explained. The trapped protons and electrons by radiation belt is discussed and the life-time of trapped particles are presented. Finally the magnetic fields of Moon, Venus, Mars, and Saturn, measured by passengers Mariner 4,10 and pioneer 10,11 are indicated. The experimental and theoretical results for the explanation of trapped plasma around the earth which is looked like two internal and external belt have almost good correspondence

43 CFR 12.2 - What policies are financial assistance awards and subawards in the form of grants and cooperative...

Science.gov (United States)

2010-10-01

..., and authorizes joint dissemination of information and promotion of activities being supported, the... your employees about the importance of wearing seat belts and the consequences of not wearing them. (ii... for their employees about the importance of wearing seat belts and the consequences of not wearing...

Buckle Up on Every Trip (A Cup of Health with CDC)

Centers for Disease Control (CDC) Podcasts

Motor-vehicle crashes are among the leading causes of injury-related deaths in the U.S. Proper seat belt use is the best way to prevent serious injuries and deaths in car crashes. In this podcast, Laurie Beck discusses the importance of regular seat belt use.

Study to develop improved fire resistant aircraft passenger seat materials

Science.gov (United States)

Duskin, F. E.; Schutter, K. J.; Sieth, H. H.; Trabold, E. L.

1980-01-01

The Phase 3 study of the NASA 'Improved Fire Resistant Aircraft Seat Materials' involved fire tests of improved materials in multilayered combinations representative of cushion configurations. Tests were conducted to determine their thermal, smoke, and fire resistance characteristics. Additionally, a 'Design Guideline' for Fire Resistant Passenger Seats was written outlining general seat design considerations. Finally, a three-abreast 'Tourist Class' passenger seat assembly fabricated from the most advanced fire-resistant materials was delivered.

Parameter study for child injury mitigation in near-side impacts through FE simulations.

Science.gov (United States)

Andersson, Marianne; Pipkorn, Bengt; Lövsund, Per

2012-01-01

The objective of this study is to investigate the effects of crash-related car parameters on head and chest injury measures for 3- and 12-year-old children in near-side impacts. The evaluation was made using a model of a complete passenger car that was impacted laterally by a barrier. The car model was validated in 2 crash conditions: the Insurance Institute for Highway Safety (IIHS) and the US New Car Assessment Program (NCAP) side impact tests. The Small Side Impact Dummy (SID-IIs) and the human body model 3 (HBM3) (Total HUman Model for Safety [THUMS] 3-year-old) finite element models were used for the parametric investigation (HBM3 on a booster). The car parameters were as follows: vehicle mass, side impact structure stiffness, a head air bag, a thorax-pelvis air bag, and a seat belt with pretensioner. The studied dependent variables were as follows: resultant head linear acceleration, resultant head rotational acceleration, chest viscous criterion, rib deflection, and relative velocity at head impact. The chest measurements were only considered for the SID-IIs. The head air bag had the greatest effect on the head measurements for both of the occupant models. On average, it reduced the peak head linear acceleration by 54 g for the HBM3 and 78 g for the SID-IIs. The seat belt had the second greatest effect on the head measurements; the peak head linear accelerations were reduced on average by 39 g (HBM3) and 44 g (SID-IIs). The high stiffness side structure increased the SID-IIs' head acceleration, whereas it had marginal effect on the HBM3. The vehicle mass had a marginal effect on SID-IIs' head accelerations, whereas the lower vehicle mass caused 18 g higher head acceleration for HBM3 and the greatest rotational acceleration. The thorax-pelvis air bag, vehicle mass, and seat belt pretensioner affected the chest measurements the most. The presence of a thorax-pelvis air bag, high vehicle mass, and a seat belt pretensioner all reduced the chest viscous criterion

Roadside observation of child passenger restraint use

Directory of Open Access Journals (Sweden)

Beth Bruce

2015-10-01

Full Text Available Background: Despite legislation and research evidence supporting the use of childhood vehicle restraints, motor vehicle crashes remain the leading cause of injury, death and disability among Canadian children. Methods: Working in collaboration with trained car seat specialists and police officers, roadside checks were conducted to observe correct use of child restraints. Results: Of the 1323 child vehicle restraints inspected, 99.6% of the children were restrained, 91% were in the correct seat, and 48% of restraints were correctly installed. The seat/restraint types most used incorrectly used were booster seats (31% and seat belts (53%. The majority of incorrectly installed or fitted seats (55% were forward facing. Common errors in installation and fit included the seat not being secured tightly enough to the vehicle, incorrect tether strap use, the harness not being tight enough, and/or the chest clip being in the wrong place. Conclusions: The greatest proportion of incorrect seat use was among those children who transitioned to a seat belt too soon. The greatest proportion of installation and fit errors were among forward facing seats. Researchers recommend: 1 targeting parents with older children (ages 3 and above regarding transitioning too soon from forward facing seats to booster seats, and from booster seats to seat belts; 2 targeting parents with younger children regarding correct installation of rear facing and forward facing seats; 3 collaborating with police officers to review the most common errors and encourage observation at roadside checks; and 4 creating community awareness by way of roadside checks.

Use of child restraint system and patterns of child transportation in Riyadh, Saudi Arabia.

Science.gov (United States)

Alsanea, Mohammd; Masuadi, Emad; Hazwani, Tarek

2018-01-01

Child restraint system (CRS) is designed to protect children from injury during motor vehicle crash (MVC). However, there is no regulation or enforcement of CRS use in Saudi Arabia. This study estimated the prevalence of CRS use and identified patterns of child transportation in Riyadh, Saudi Arabia. In this cross-sectional study, a self-administered questionnaire was distributed across Riyadh targeting families who drove with children aged less than 5 years. The questionnaire inquired about CRS availability, patterns of child transportation if a CRS was unavailable, seat belt use by the driver and adult passengers, and the perception of CRS. Of 385 respondents, only 36.6% reported the availability of a CRS (95% CI: 31.8-41.7%), with only half of those reported consistent use 74 (52.2%). Nearly 30% of all children aged less than 5 years were restrained during car journeys. Sitting on the lap of an adult passenger on the front seat was the most common pattern of child transportation (54.5%). Approximately 13.5% of respondents were involved in an MVC while driving with children; 63.5% of these children were unprotected by any safety system. Seat belt use by drivers was low, with only 15.3% reporting constant use. The prevalence of CRS use in Riyadh is low, and safety practices are seldom used by drivers and passengers. In addition to legal enforcement of CRS use, implementation of a child transportation policy with age-appropriate height and weight specifications is imperative.

Development and validation of rear impact computer simulation model of an adult manual transit wheelchair with a seated occupant.

Science.gov (United States)

Salipur, Zdravko; Bertocci, Gina

2010-01-01

It has been shown that ANSI WC19 transit wheelchairs that are crashworthy in frontal impact exhibit catastrophic failures in rear impact and may not be able to provide stable seating support and thus occupant protection for the wheelchair occupant. Thus far only limited sled test and computer simulation data have been available to study rear impact wheelchair safety. Computer modeling can be used as an economic and comprehensive tool to gain critical knowledge regarding wheelchair integrity and occupant safety. This study describes the development and validation of a computer model simulating an adult wheelchair-seated occupant subjected to a rear impact event. The model was developed in MADYMO and validated rigorously using the results of three similar sled tests conducted to specifications provided in the draft ISO/TC 173 standard. Outcomes from the model can provide critical wheelchair loading information to wheelchair and tiedown manufacturers, resulting in safer wheelchair designs for rear impact conditions. (c) 2009 IPEM. Published by Elsevier Ltd. All rights reserved.

Multi-leg Seat Inventory Control Based on EMSU and Virtual Bucket

Directory of Open Access Journals (Sweden)

Wei Fan

2014-01-01

Full Text Available Expected marginal seat revenue (EMSR is a well-known method for airline seat inventory control airlines. However, this method employs a static model to study the dynamic reservation process, and does not take into account the risk tolerance of policy makers. Expected marginal seat utility (EMSU replaces revenue by utility, which addresses the real situation of seat inventory control. However, there is still a lack of multi-leg seat control algorithms based on EMSU. Therefore, using EMSU and bucket algorithms, this paper applies the Markov decision-making process to simulate the flight reservation process and builds a dynamic multi-leg seat inventory control model. Experimental results validate the effectiveness of the proposed method.

Risk of injury for occupants of motor vehicle collisions from unbelted occupants.

Science.gov (United States)

MacLennan, P A; McGwin, G; Metzger, J; Moran, S G; Rue, L W

2004-12-01

Unbelted occupants may increase the risk of injury for other occupants in a motor vehicle collision (MVC). This study evaluated the association between occupant restraint use and the risk of injury (including death) to other vehicle occupants. A population based cohort study. United States. MVC occupants (n = 152 191 unweighted, n = 18 426 684 weighted) seated between a belted or unbelted occupant and the line of the principal direction of force in frontal, lateral, and rear MVCs were sampled from the 1991-2002 National Automotive Sampling System General Estimates System. Offset MVCs were not included in the study. Risk ratios and 95% confidence intervals for injury (including death) for occupants seated contiguous to unbelted occupants compared to occupants seated contiguous to belted occupants. Risk ratios were adjusted for at risk occupant's sex, age, seating position, vehicle type, collision type, travel speed, crash severity, and at risk occupants' own seat belt use. Exposure to unbelted occupants was associated with a 40% increased risk of any injury. Belted at risk occupants were at a 90% increased risk of injury but unbelted occupants were not at increased risk. Risks were similar for non-incapacitating and capacitating injuries. There was a 4.8-fold increased risk of death for exposed belted occupants but no increased risk of death for unbelted occupants. Belted occupants are at an increased risk of injury and death in the event of a MVC from unbelted occupants.

Kineto-dynamic design optimisation for vehicle-specific seat-suspension systems

Science.gov (United States)

Shangguan, Wen-Bin; Shui, Yijie; Rakheja, Subhash

2017-11-01

Designs and analyses of seat-suspension systems are invariably performed considering effective vertical spring rate and damping properties, while neglecting important contributions due to kinematics of the widely used cross-linkage mechanism. In this study, a kineto-dynamic model of a seat-suspension is formulated to obtain relations for effective vertical suspension stiffness and damping characteristics as functions of those of the air spring and the hydraulic damper, respectively. The proposed relations are verified through simulations of the multi-body dynamic model of the cross-linkage seat-suspension in the ADAMS platform. The validity of the kineto-dynamic model is also demonstrated through comparisons of its vibration transmission response with the experimental data. The model is used to identify optimal air spring coordinates to attain nearly constant natural frequency of the suspension, irrespective of the seated body mass and seated height. A methodology is further proposed to identify optimal damping requirements for vehicle-specific suspension designs to achieve minimal seat effective amplitude transmissibility (SEAT) and vibration dose value (VDV) considering vibration spectra of different classes of earthmoving vehicles. The shock and vibration isolation performance potentials of the optimal designs are evaluated under selected vehicle vibration superimposed with shock motions. Results show that the vehicle-specific optimal designs could provide substantial reductions in the SEAT and VDV values for the vehicle classes considered.

Belt conveyor apparatus

Science.gov (United States)

Oakley, David J.; Bogart, Rex L.

1987-01-01

A belt conveyor apparatus according to this invention defines a conveyance path including a first pulley and at least a second pulley. An endless belt member is adapted for continuous travel about the pulleys and comprises a lower portion which engages the pulleys and an integral upper portion adapted to receive objects therein at a first location on said conveyance path and transport the objects to a second location for discharge. The upper belt portion includes an opposed pair of longitudinally disposed crest-like members, biased towards each other in a substantially abutting relationship. The crest-like members define therebetween a continuous, normally biased closed, channel along the upper belt portion. Means are disposed at the first and second locations and operatively associated with the belt member for urging the normally biased together crest-like members apart in order to provide access to the continuous channel whereby objects can be received into, or discharged from the channel. Motors are in communication with the conveyance path for effecting the travel of the endless belt member about the conveyance path. The conveyance path can be configured to include travel through two or more elevations and one or more directional changes in order to convey objects above, below and/or around existing structures.

Tectonics, Deep-Seated Structure and Recent Geodynamics of the Caucasus

Science.gov (United States)

Amanatashvili, I.; Adamia, Sh.; Lursmanashvili, N.; Sadradze, N.; Meskhia, V.; Koulakov, I.; Zabelina, I.; Jakovlev, A.

2012-04-01

The tectonics and deep-seated structure of the Caucasus are determined by its position between the still converging Eurasian and Africa-Arabian plates, within a wide zone of continental collision. The region in the Late Proterozoic - Early Cenozoic belonged to the Tethys Ocean and its Eurasian and Africa-Arabian margins. During Oligocene-Middle Miocene and Late Miocene-Quaternary time as a result of collision back-arc basins were inverted to form fold-thrust mountain belts and the Transcaucasian intermontane lowlands. The Caucasus is divided into platform and fold-thrust units, and forelands superimposed mainly on the rigid platform zones. The youngest structural units composed of Neogene-Quaternary continental volcanic formations of the Armenian and Javakheti highlands and extinct volcanoes of the Great Caucasus. As a result of detailed geophysical study of the gravity, magnetic, seismic, and thermal fields, the main features of the deep crustal structure of the Caucasus have been determined. Knowledge on the deep lithospheric structure of the Caucasus region is based on surface geology and deep and super deep drilling data combined with gravity, seismic, heat flow, and magnetic investigations. Close correlation between the geology and its deep-seated structures appears in the peculiarities of spatial distribution of gravitational, thermal and magnetic fields, particularly generally expressed in orientation of regional anomalies that is in good agreement with general tectonic structures. In this study we present two tomographic models derived for the region based on two different tomographic approaches. In the first case, we use the travel time data on regional seismicity recorded by networks located in Caucasus. The tomographic inversion is based on the LOTOS code which enables simultaneous determination of P and S velocity distributions and source locations. The obtained model covers the crustal and uppermost mantle depths. The second model, which is constructed

Predicting the effectiveness of road safety campaigns through alternative research designs.

Science.gov (United States)

Adamos, Giannis; Nathanail, Eftihia

2016-12-01

A large number of road safety communication campaigns have been designed and implemented in the recent years; however their explicit impact on driving behavior and road accident rates has been estimated in a rather low proportion. Based on the findings of the evaluation of three road safety communication campaigns addressing the issues of drinking and driving, seat belt usage, and driving fatigue, this paper applies different types of research designs (i.e., experimental, quasi-experimental, and non-experimental designs), when estimating the effectiveness of road safety campaigns, implements a cross-design assessment, and conducts a cross-campaign evaluation. An integrated evaluation plan was developed, taking into account the structure of evaluation questions, the definition of measurable variables, the separation of the target audience into intervention (exposed to the campaign) and control (not exposed to the campaign) groups, the selection of alternative research designs, and the appropriate data collection methods and techniques. Evaluating the implementation of different research designs in estimating the effectiveness of road safety campaigns, results showed that the separate pre-post samples design demonstrated better predictability than other designs, especially in data obtained from the intervention group after the realization of the campaign. The more constructs that were added to the independent variables, the higher the values of the predictability were. The construct that most affects behavior is intention, whereas the rest of the constructs have a lower impact on behavior. This is particularly significant in the Health Belief Model (HBM). On the other hand, behavioral beliefs, normative beliefs, and descriptive norms, are significant parameters for predicting intention according to the Theory of Planned Behavior (TPB). The theoretical and applied implications of alternative research designs and their applicability in the evaluation of road safety

75 FR 30783 - Agency Information Collection Activities; Proposed Collection; Comment Request; Safety Standard...

Science.gov (United States)

2010-06-02

... product and the retail package. There are three known firms supplying bath seats to the United States... marking and instructional literature requirements in the Safety Standard for Infant Bath Seats. DATES... for marking and instructional literature. We estimate the burden of this collection of information as...

Classroom Seating Considerations for 21st Century Students and Faculty

Science.gov (United States)

Harvey, Eugene J.; Kenyon, Melaine C.

2013-01-01

This quantitative, cross-sectional research study explored students' perceptions of five different seating styles within typical classrooms in an urban public higher education institution. The five seating styles included: modern mobile chairs, tablet arm chairs, fixed tiered seating with tablet arms, rectangle tables with standard chairs, and…

Seat belt control : semi-active belt force actuator

NARCIS (Netherlands)

Deen, I.J.; Jager, de A.G.; Steinbuch, M.

2013-01-01

Letsel aan de borstkas ten gevolge van de autogordel bij (frontale) botsingen komt erg vaak voor. Promotieonderzoek van E.P. van der Laan heeft een continu krachtgeregeld gordelsysteem opgeleverd waarmee dergelijk letsel verminderd zou moeten worden. De praktische uitvoering van dit model bestaat

Thermal comfort of seats as visualized by infrared thermography.

Science.gov (United States)

Sales, Rosemary Bom Conselho; Pereira, Romeu Rodrigues; Aguilar, Maria Teresa Paulino; Cardoso, Antônio Valadão

2017-07-01

Published studies that deal with the question of how the temperature of chair seats influences human activities are few, but the studies considering such a factor, a function of the type of material, could contribute to improvements in the design of chairs. This study evaluates seat temperatures of 8 types of chairs made of different materials. The parts of the furniture that people come into contact with, and the thermal response of the material to heating and cooling have been evaluated. Infrared thermography was used for this, as it is a non-contact technique that does not present any type of risk in the measurement of temperatures. Seats made of synthetic leather (leatherette), wood and polyester fabric were found to have the highest temperatures, and the plywood seat showed the lowest. The study has also revealed that thermography can contribute to studies of thermal comfort of chair seats in addition to determining the most suitable material. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of vehicle front-end stiffness on rear seat dummies in NCAP and FMVSS208 tests.

Science.gov (United States)

Sahraei, Elham; Digges, Kennerly; Marzougui, Dhafer

2013-01-01

This study is devoted to quantifying changes in mass and stiffness of vehicles tested by the National Highway Traffic Safety Administration (NHTSA) over the past 3 decades (model years 1982 to 2010) and understanding the effect of those changes on protection of rear seat occupants. A total of 1179 tests were used, and the changes in their mass and stiffness versus their model year was quantified. Additionally, data from 439 dummies tested in rear seats of NHTSA's full frontal crashes were analyzed. Dummies were divided into 3 groups based on their reference injury criteria. Multiple regressions were performed with speed, stiffness, and mass as predicting variables for head, neck, and chest injury criteria. A significant increase in mass and stiffness over model year of vehicles was observed, for passenger cars as well as large platform vehicles. The result showed a significant correlation (P-value < .05) between the increase in stiffness of the vehicles and increase in head and chest injury criteria for all dummy sizes. These results explain that stiffness is a significant contributor to previously reported decreases in protection of rear seat occupants over model years of vehicles.

Analysis of stress distribution of timing belts by FEM; Yugen yosoho ni yoru timing belt oryoku kaiseki (belt code oryoku bunpu kaiseki hokoku)

Energy Technology Data Exchange (ETDEWEB)

Furukawa, Y; Tomono, K; Takahashi, H; Uchida, T [Honda R and D Co. Ltd., Tokyo (Japan)

1997-10-01

A model of the belt analyzed by-ABAQUS (: a general nonlinear finite element program) successfully confirmed the mechanism that generates the belt cord stress. A quite good agreement between experimental and computed results for the stress distribution of the belt cord. It is found that maximum stress of the cords occurs near the root of the tooth by calculation, where the belt cords break off. 3 refs., 9 figs.

Assessment of Rail Seat Abrasion Patterns and Environment

Science.gov (United States)

2012-05-01

Rail seat abrasion (RSA) of concrete ties is manifested by the loss of material under the rail seat area and, in extreme cases, results in loss of rail clip holding power, reverse rail cant, and gauge widening. RSA was measured in several curves on t...

Health impact assessment of the Atlanta BeltLine.

Science.gov (United States)

Ross, Catherine L; Leone de Nie, Karen; Dannenberg, Andrew L; Beck, Laurie F; Marcus, Michelle J; Barringer, Jason

2012-03-01

Although a health impact assessment (HIA) is a tool that can provide decision makers with recommendations to promote positive health impacts and mitigate adverse health impacts of proposed projects and policies, it is not routinely conducted on most major projects or policies. To make health a decision criterion for the Atlanta BeltLine, a multibillion-dollar transit, trails, parks, and redevelopment project. An HIA was conducted in 2005-2007 to anticipate and influence the BeltLine's effect on health determinants. Changes in access and equity, environmental quality, safety, social capital, and physical activity were forecast, and steps to maximize health benefits and reduce negative effects were recommended. Key recommendations included giving priority to the construction of trails and greenspace rather than residential and retail construction, making health an explicit goal in project priority setting, adding a public health professional to decision-making boards, increasing the connectivity between the BeltLine and civic spaces, and ensuring that affordable housing is built. BeltLine project decision makers have incorporated most of the HIA recommendations into the planning process. The HIA was cited in the awarding of additional funds of $7,000,000 for brownfield clean-up and greenspace development. The project is expected to promote the health of local residents more than in the absence of the HIA. This report is one of the first HIAs to tie specific assessment findings to specific recommendations and to identifiable impacts from those recommendations. The lessons learned from this project may help others engaged in similar efforts. Copyright © 2012. Published by Elsevier Inc.

Vibration control of an energy regenerative seat suspension with variable external resistance

Science.gov (United States)

Ning, Donghong; Sun, Shuaishuai; Du, Haiping; Li, Weihua; Zhang, Nong

2018-06-01

In this paper, an energy regenerative seat suspension with a variable external resistance is proposed and built, and a semi-active controller for its vibration control is also designed and validated. The energy regenerative seat suspension is built with a three-phase generator and a gear reducer, which are installed in the scissors structure centre of the seat suspension, and the vibration energy is directly harvested from the rotary movement of suspension's scissors structure. The electromagnetic torque of the semi-active seat suspension actuator is controlled by an external variable resistor. An integrated model including the seat suspension's kinematics and the generator is built and proven to match the test result very well. A simplified experimental phenomenon model is also built based on the test results for the controller design. A state feedback H∞ controller is proposed for the regenerative seat suspension's semi-active vibration control. The proposed regenerative seat suspension and its controller are validated with both simulations and experiments. A well-tuned passive seat suspension is applied to evaluate the regenerative seat's performance. Based on ISO 2631-1, the frequency-weighted root mean square (FW-RMS) acceleration of the proposed seat suspension has a 22.84% reduction when compared with the passive one, which indicates the improvement of ride comfort. At the same time, the generated RMS power is 1.21 W. The proposed regenerative seat suspension can greatly improve the driver's ride comfort and has the potential to be developed to a self-powered semi-active system.

The Effects of Prototype Helicopter Seat Cushion Concepts on Human Body Vibration Response

National Research Council Canada - National Science Library

Smith, Suzanne

1998-01-01

...), and thigh, and the input at the seat. Seating configurations included the rigid seat, a current inventory seat cushion, and a prototype cushion with an inflatable thigh support in both the deflated and inflated positions...

75 FR 30775 - Availability of Seats for the Monitor National Marine Sanctuary Advisory Council

Science.gov (United States)

2010-06-02

..., Recreational Diving seat, Education seat, Archaeological Research seat, Maritime Museum seat, Youth seat, and... by NOAA's Office of National Marine Sanctuaries. It is one of 13 sanctuaries and protects the wreck..., Recreational Diving, the US Navy, Virginia and North Carolina Department of Historic Resources, the National...

Investigating Car Body Construction Influence on the Passive Safety in a Rear Impact

Directory of Open Access Journals (Sweden)

D. Yu. Solopov

2015-01-01

Full Text Available This article solves the task to assess how much a car body construction influences on the parameters of passive safety in a rear impact. The task concerns the impact and, as a result, is highly nonlinear with large values of deformations, stresses, and accelerations. A finite element method based on software systems LS-DYNA, ANSYS, FEMAP, and others solves this task.One of the most important stages of the work was to develop the finite element models (FEM of the car as a whole, as well as the car seat with a dummy mounted in the car. Body of the Chiseler Grand Caravan car, which parameters are close to average ones, was used as an object of research.The results of calculations and experiments allowed us to find that in assessing the passive safety of a car, taking into consideration the body design with a seat mounted in it, values of velocities, accelerations, and NIC criterion turned out to be lower than when calculating the seat with a dummy separately. The relative error (relative to the results of calculations in the "dangerous" impact of FEM seat of the highest level in accordance with EURO NCAP was 32% for full acceleration and was 33% for NIC criterion.It was found that in the calculations based on the FEM car, as a whole, the results are more accurate than when using the load operation conditions simulating energy absorption by the car body (20%.This leads to the conclusion that the calculations based on the FEM car with the seat mounted in it gives the possibility to design a seat (with passive or active headrest to ensure the best level of passive safety of this car.

Belt drive construction improvement

Directory of Open Access Journals (Sweden)

I.Yu. Khomenko

2012-08-01

Full Text Available The possibility of the traction capacity increase of the belt drive TRK is examined. This was done for the purpose of air conditioning system of passenger car with double-generator system energy supplying. Belts XPC (made by the German firm «Continental ContiTech» testing were conducted. The results confirmed the possibility of their usage in order to improve belt drive TRK characteristics.

Continuous Mass Measurement on Conveyor Belt

Science.gov (United States)

Tomobe, Yuki; Tasaki, Ryosuke; Yamazaki, Takanori; Ohnishi, Hideo; Kobayashi, Masaaki; Kurosu, Shigeru

The continuous mass measurement of packages on a conveyor belt will become greatly important. In the mass measurement, the sequence of products is generally random. An interesting possibility of raising throughput of the conveyor line without increasing the conveyor belt speed is offered by the use of two or three conveyor belt scales (called a multi-stage conveyor belt scale). The multi-stage conveyor belt scale can be created which will adjust the conveyor belt length to the product length. The conveyor belt scale usually has maximum capacities of less than 80kg and 140cm, and achieves measuring rates of more than 150 packages per minute and more. The output signals from the conveyor belt scale are always contaminated with noises due to vibrations of the conveyor and the product to be measured in motion. In this paper an employed digital filter is of Finite Impulse Response (FIR) type designed under the consideration on the dynamics of the conveyor system. The experimental results on the conveyor belt scale suggest that the filtering algorithms are effective enough to practical applications to some extent.

The Surprising Impact of Seat Location on Student Performance

Science.gov (United States)

Perkins, Katherine K.; Wieman, Carl E.

2005-01-01

Every physics instructor knows that the most engaged and successful students tend to sit at the front of the class and the weakest students tend to sit at the back. However, it is normally assumed that this is merely an indication of the respective seat location preferences of weaker and stronger students. Here we present evidence suggesting that in fact this may be mixing up the cause and effect. It may be that the seat selection itself contributes to whether the student does well or poorly, rather than the other way around. While a number of studies have looked at the effect of seat location on students, the results are often inconclusive, and few, if any, have studied the effects in college classrooms with randomly assigned seats. In this paper, we report on our observations of a large introductory physics course in which we randomly assigned students to particular seat locations at the beginning of the semester. Seat location during the first half of the semester had a noticeable impact on student success in the course, particularly in the top and bottom parts of the grade distribution. Students sitting in the back of the room for the first half of the term were nearly six times as likely to receive an F as students who started in the front of the room. A corresponding but less dramatic reversal was evident in the fractions of students receiving As. These effects were in spite of many unusual efforts to engage students at the back of the class and a front-to-back reversal of seat location halfway through the term. These results suggest there may be inherent detrimental effects of large physics lecture halls that need to be further explored.

Equilibria and Free Vibration of a Two-Pulley Belt-Driven System with Belt Bending Stiffness

Directory of Open Access Journals (Sweden)

Jieyu Ding

2014-01-01

Full Text Available Nonlinear equilibrium curvatures and free vibration characteristics of a two-pulley belt-driven system with belt bending stiffness and a one-way clutch are investigated. With nonlinear dynamical tension, the transverse vibrations of the translating belt spans and the rotation motions of the pulleys and the accessory shaft are coupled. Therefore, nonlinear piecewise discrete-continuous governing equations are established. Considering the bending stiffness of the translating belt spans, the belt spans are modeled as axially moving beams. The pattern of equilibria is a nontrivial solution. Furthermore, the nontrivial equilibriums of the dynamical system are numerically determined by using two different approaches. The governing equations of the vibration near the equilibrium solutions are derived by introducing a coordinate transform. The natural frequencies of the dynamical systems are studied by using the Galerkin method with various truncations and the differential and integral quadrature methods. Moreover, the convergence of the Galerkin truncation is investigated. Numerical results reveal that the study needs 16 terms after truncation in order to determine the free vibration characteristics of the pulley-belt system with the belt bending stiffness. Furthermore, the first five natural frequencies are very sensitive to the bending stiffness of the translating belt.

Use of child restraint system and patterns of child transportation in Riyadh, Saudi Arabia.

Directory of Open Access Journals (Sweden)

Mohammd Alsanea

Full Text Available Child restraint system (CRS is designed to protect children from injury during motor vehicle crash (MVC. However, there is no regulation or enforcement of CRS use in Saudi Arabia. This study estimated the prevalence of CRS use and identified patterns of child transportation in Riyadh, Saudi Arabia.In this cross-sectional study, a self-administered questionnaire was distributed across Riyadh targeting families who drove with children aged less than 5 years. The questionnaire inquired about CRS availability, patterns of child transportation if a CRS was unavailable, seat belt use by the driver and adult passengers, and the perception of CRS.Of 385 respondents, only 36.6% reported the availability of a CRS (95% CI: 31.8-41.7%, with only half of those reported consistent use 74 (52.2%. Nearly 30% of all children aged less than 5 years were restrained during car journeys. Sitting on the lap of an adult passenger on the front seat was the most common pattern of child transportation (54.5%. Approximately 13.5% of respondents were involved in an MVC while driving with children; 63.5% of these children were unprotected by any safety system. Seat belt use by drivers was low, with only 15.3% reporting constant use.The prevalence of CRS use in Riyadh is low, and safety practices are seldom used by drivers and passengers. In addition to legal enforcement of CRS use, implementation of a child transportation policy with age-appropriate height and weight specifications is imperative.

49 CFR 571.213 - Standard No. 213; Child restraint systems.

Science.gov (United States)

2010-10-01

... vehicle seat cushion and vehicle seat back. (b) Harnesses manufactured for use on school bus seats must... humidity between 48 and 67 percent, and any ambient temperature between 70° and 77 °F. Measure belt webbing...

Joint overbooking and seat allocation for fare families

DEFF Research Database (Denmark)

Hjorth, Robert; Fiig, Thomas; Bondoux, Nicolas

2016-01-01

Revenue Management Systems (RMS) traditionally solve the seat allocation problem separately from the overbooking problem. Overbooking is managed by inflating the authorization levels obtained from seat allocation by various heuristics. This approach although suboptimal, is necessitated because...... independent demand model, which is readily solved. The resulting availability control can easily by implemented in existing RMS...

MIT-Skywalker: Evaluating comfort of bicycle/saddle seat.

Science.gov (United States)

Goncalves, Rogerio S; Hamilton, Taya; Daher, Ali R; Hirai, Hiroaki; Krebs, Hermano I

2017-07-01

The MIT-Skywalker is a robotic device developed for the rehabilitation of gait and balance after a neurological injury. This device has been designed based on the concept of a passive walker and provides three distinct training modes: discrete movement, rhythmic movement, and balance training. In this paper, we present our efforts to evaluate the comfort of a bicycle/saddle seat design for the system's novel actuated body weight support device. We employed different bicycle and saddle seats and evaluated comfort using objective and subjective measures. Here we will summarize the results obtained from a study of fifteen healthy subjects and one stroke patient that led to the selection of a saddle seat design for the MIT-Skywalker.

Autist mobile seat's frame strength simulation used in a car

Science.gov (United States)

Suryo, S. H.; Jamari, J.; Naufal, G. K.; Ismail, R.; Bayuseno, A. P.; Desiningrum, D. R.

2016-04-01

Going on a car with autistic children needs a special handling. Autistic children that tend to be hyperactive in the car may disturb driving. A tool is needed to keep them in a calm state when they are in the car. Autist Mobile Seat is an aid for the autistic children when going on a car. The aid is an additional seat paired with the main seat of the car. This aid consists of three main things: Main frame, body skin, and pneumatic system. Frame as the main component supporting the Autist Mobile Seat functions as a holder as well as a body skin retainer in order to be able to retain the body of the autistic children. The strength of the frame from this Autist Mobile Seat should be counted as an anticipation from the failure of the frame function when receiving load when used by the autistic children in the car. Consequently, a test on the frame of the Autist Mobile Seat towards the load received should be conducted by using a method of FEM (Finite Element Method) with the help of commercial software. The simulation produces the maximum strength, the frame towards the load received as well as the critical point on the frame when loading occurs.

The Impact of Seating Location and Seating Type on Student Performance

Science.gov (United States)

Meeks, Michael D.; Knotts, Tami L.; James, Karen D.; Williams, Felice; Vassar, John A.; Wren, Amy Oakes

2013-01-01

While an extensive body of research exists regarding the delivery of course knowledge and material, much less attention has been paid to the performance effect of seating position within a classroom. Research findings are mixed as to whether students in the front row of a classroom outperform students in the back row. Another issue that has not…

Belt technology stretches conveyors' coverage

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-15

With China the leading growth engine in the conveyor market, leading belt manufacturers are establishing local manufacturing plants to boost their presence. Fenner is planning to almost triple production capacity over the next three years, with a third of its investment in China. Shanxi-Phoenix Conveyor Belt Systems is a joint venture between Phoenix Conveyor Belt Systems GmbH, now part of ContiTech Ag, and its Chinese partners Lu An Mining Group Co. Ltd. and Jingcheng Anthracite Group Co. Ltd. It manufacturers steel cable belts, PVC and multi-ply belts for coal mines and power plants. Recent belt designs by FennerEurope and Metso Minerals are reported. 2 photos.

"Hot Seat" Questioning: A Technique to Promote and Evaluate Student Dialogue

Science.gov (United States)

Crider, Anthony

Several approaches have been proposed to include students in classroom dialogue, including "think-pair-share" and "talk to your neighbor." I recently implemented an additional technique in which four students answer questions in a "Hot Seat" at the front of the classroom. An unforeseen by-product of this was student-initiated peer instruction outside of the classroom. A small case study (approximately 50 students) on the effect of the Hot Seat using the midterm exam showed that students were 9.5 +/- 3.2% more likely to correctly answer a question related to material covered while they occupied the Hot Seat. Analysis of the Astronomy Diagnostic Test revealed that they were twice as likely to learn their Hot Seat material. A survey revealed one likely reason: Students typically spent 15-60 additional minutes preparing for class on their two assigned Hot Seat dates. Curiously, students received no significant benefit (2.2 +/- 3.6%) from their second turn in the Hot Seat, possibly reflecting student immunization to its motivational pressure.

Finite Element Models Development of Car Seats With Passive Head Restraints to Study Their Meeting Requirements for EURO NCAP

Directory of Open Access Journals (Sweden)

D. Yu. Solopov

2014-01-01

Full Text Available In performing calculations to evaluate passive safety of car seats by computer modelling methods it is desirable to use the final element models (FEM thereby providing the greatest accuracy of calculation results. Besides, it is expedient to use FEM, which can be calculated by computer for a small period of time to give preliminary results for short terms.The paper describes the features to evaluate a passive safety, which is ensured by the developed KEM of seats with passive head restraints according to requirements of the EURO NCAP.Besides, accuracy of calculated results that is provided by the developed KEM was evaluated. Accuracy evaluation was accomplished in relation to the results obtained the by specialists of the organization conducting similar researches (LSTC.This work was performed within the framework of a technique, which allows us to develop effectively the car seat designs both with passive, and active head restraints, meeting requirements for passive safety.By results of made calculations and experiments it was found that when evaluating by the EURO NCAP technique the "rough" KEM (the 1st and 2nd levels can be considered as rational ones (in terms of labour costs for its creation and problem solving as well as by result errors and it is expedient to use them for preliminary and multivariate calculations. Detailed models (the 3rd level provide the greatest accuracy (the greatest accuracy is reached with the evaluated impact of 16km/h speed under the loading conditions "moderate impact". A relative error of full head acceleration is of 12%.In evaluation by EURO NCAP using NIC criterion a conclusion can be drawn that the seat models of the 2nd level (467 936 KE and the 3rd level (1 255 358 KE meet the passive safety requirements according to EURO NCAP requirements under "light", "moderate", and "heavy" impacts.In evaluation by EURO NCAP for preliminary and multivariate calculations a model of the middle level (consisting of 467

Assessing community child passenger safety efforts in three Northwest Tribes.

Science.gov (United States)

Smith, M L; Berger, L R

2002-12-01

To identify strengths and weaknesses in community based child passenger safety programs by developing a scoring instrument and conducting observations of child restraint use in three Native American communities. The three communities are autonomous Tribal reservations in the Pacific Northwest. Their per capita incomes and rates of unemployment are comparable. In each community, 100 children under 5 years old were observed for car seat use. A six item community assessment tool (100 points maximum) awarded points for such items as the type (primary or secondary) and enforcement of child restraint laws; availability of car seats from distribution programs; extent of educational programs; and access to data on vehicle injuries. For children from birth to 4 years, the car seat use rate ranged from 12%-21%. Rates for infants (71%-80%) far exceeded rates for 1-4 year old children (5%-14%). Community scores ranged from 0 to 31.5 points. There was no correlation between scores and observed car seat use. One reason was the total lack of enforcement of restraint laws. A community assessment tool can highlight weaknesses in child passenger efforts. Linking such a tool with an objective measure of impact can be applied to other injury problems, such as fire safety or domestic violence. The very process of creating and implementing a community assessment can enhance agency collaboration and publicize evidence based "best practices" for injury prevention. Further study is needed to address methodologic issues and to examine crash and medical data in relation to community child passenger safety scores.

Buckle Up on Every Trip (A Cup of Health with CDC)

Centers for Disease Control (CDC) Podcasts

2013-05-23

Motor-vehicle crashes are among the leading causes of injury-related deaths in the U.S. Proper seat belt use is the best way to prevent serious injuries and deaths in car crashes. In this podcast, Laurie Beck discusses the importance of regular seat belt use.  Created: 5/23/2013 by MMWR.   Date Released: 5/23/2013.

Understanding international road safety disparities: Why is Australia so much safer than the United States?

Science.gov (United States)

Marshall, Wesley E

2018-02-01

Despite similarities to the US in terms of transportation, land use, and culture, Australia kills 5.3 people per 100,000 population on the roads each year, as compared to the US rate of 12.4. Similar trends hold when accounting for distance driven and the number of registered cars. This paper seeks to understand what is behind the road safety disparities between these two countries. The results suggest that a number of inter-related factors seem to play a role in the better road safety outcomes of Australia as compared to the US. This includes Australia's strategies related to seat belt usage and impaired driving as well as their efforts to help curb vehicle speeds and reduce exposure. Design-related differences include a much greater reliance on roundabouts and narrower street cross-sections as well as guidelines that encourage self-enforcing roads. Policy-related differences include stronger and more extensive enforcement programs, restrictive licensing programs, and higher driving costs. Combined with a more urban population and multimodal infrastructure, Australia tends to discourage driving mileage and exposure while encouraging safer modes of transportation such as transit, at least more so than in most of the US. Australia also enacted their version of Vision Zero - called the Safe System Approach - more than a decade before similar policies began cropping up in US cities. While it is difficult to attribute recent road safety successes to any specific policy, Australia continues to expand their lead on the US in terms of safety outcomes and is a road safety example worthy of consideration. Copyright © 2017 Elsevier Ltd. All rights reserved.

Resection of deep-seated brain glioma by microsurgery assisted with neuronavigation

International Nuclear Information System (INIS)

Feng Ming; Zhou Youxin; Sun Chunming; Zhang Shiming

2009-01-01

Objective: To investigate the clinical value of neuronavigator assisted microsurgery for deep-seated brain glioma. Methods: The electromagnetic neuronavigation system had been applied for microsurgery of deep-seated brain glioma in fifteen cases. Results: Ten from 15 patients were totally removed, 2 were subtotally removed and 3 were partial removed.All patients had no new neurological deficit. Conclusion: The neuronavigator assisted microsurgery for deep-seated brain glioma is of characters including accurate location, minimal invasiveness, and can enhance the rate of total resection and decrease the operative complications in the patients with deep-seated brain glioma. (authors)

A new landing impact attenuation seat in manned spacecraft biologically-inspired by felids

Directory of Open Access Journals (Sweden)

Yu Hui

2015-04-01

Full Text Available When manned spacecraft comes back to the earth, it relies on the impact attenuation seat to protect astronauts from injuries during landing phase. Hence, the seat needs to transfer impact load, as small as possible, to the crew. However, there is little room left for traditional seat to improve further. Herein, a new seat system biologically-inspired by felids’ landing is proposed. Firstly, a series of experiments was carried out on cats and tigers, in which they were trained to jump down voluntarily from different heights. Based on the ground reaction forces combined with kinematics, the experiment indicated that felids’ landing after self-initial jump was a multi-step impact attenuation process and the new seat was inspired by this. Then the construction and work process of new seat were redesigned to realize the multi-step impact attenuation. The dynamic response of traditional and new seat is analyzed under the identical conditions and the results show that the new concept seat can significantly weaken the occupant overload in two directions compared with that of traditional seat. As a consequence, the risk of injury evaluated for spinal and head is also lowered, meaning a higher level of protection which is especially beneficial to the debilitated astronaut.

Powerful conveyer belt real-time online detection system based on x-ray

Science.gov (United States)

Rong, Feng; Miao, Chang-yun; Meng, Wei

2009-07-01

The powerful conveyer belt is widely used in the mine, dock, and so on. After used for a long time, internal steel rope of the conveyor belt may fracture, rust, joints moving, and so on .This would bring potential safety problems. A kind of detection system based on x-ray is designed in this paper. Linear array detector (LDA) is used. LDA cost is low, response fast; technology mature .Output charge of LDA is transformed into differential voltage signal by amplifier. This kind of signal have great ability of anti-noise, is suitable for long-distance transmission. The processor is FPGA. A IP core control 4-channel A/D convertor, achieve parallel output data collection. Soft-core processor MicroBlaze which process tcp/ip protocol is embedded in FPGA. Sampling data are transferred to a computer via Ethernet. In order to improve the image quality, algorithm of getting rid of noise from the measurement result and taking gain normalization for pixel value is studied and designed. Experiments show that this system work well, can real-time online detect conveyor belt of width of 2.0m and speed of 5 m/s, does not affect the production. Image is clear, visual and can easily judge the situation of conveyor belt.

On statistical inference in time series analysis of the evolution of road safety.

Science.gov (United States)

Commandeur, Jacques J F; Bijleveld, Frits D; Bergel-Hayat, Ruth; Antoniou, Constantinos; Yannis, George; Papadimitriou, Eleonora

2013-11-01

Data collected for building a road safety observatory usually include observations made sequentially through time. Examples of such data, called time series data, include annual (or monthly) number of road traffic accidents, traffic fatalities or vehicle kilometers driven in a country, as well as the corresponding values of safety performance indicators (e.g., data on speeding, seat belt use, alcohol use, etc.). Some commonly used statistical techniques imply assumptions that are often violated by the special properties of time series data, namely serial dependency among disturbances associated with the observations. The first objective of this paper is to demonstrate the impact of such violations to the applicability of standard methods of statistical inference, which leads to an under or overestimation of the standard error and consequently may produce erroneous inferences. Moreover, having established the adverse consequences of ignoring serial dependency issues, the paper aims to describe rigorous statistical techniques used to overcome them. In particular, appropriate time series analysis techniques of varying complexity are employed to describe the development over time, relating the accident-occurrences to explanatory factors such as exposure measures or safety performance indicators, and forecasting the development into the near future. Traditional regression models (whether they are linear, generalized linear or nonlinear) are shown not to naturally capture the inherent dependencies in time series data. Dedicated time series analysis techniques, such as the ARMA-type and DRAG approaches are discussed next, followed by structural time series models, which are a subclass of state space methods. The paper concludes with general recommendations and practice guidelines for the use of time series models in road safety research. Copyright © 2012 Elsevier Ltd. All rights reserved.

Traveling with children: beyond car seat safety.

Science.gov (United States)

Polli, Janaina Borges; Polli, Ismael

2015-01-01

To spread knowledge and instigate the health professional to give advice on childcare during travels and on child transport safety. Literature review through the LILACS and MEDLINE(®) databases, using the terms: travel, safety, protective equipment, child, preventive medicine, retrieving articles published in the last 21 years. The authors analyzed 93 articles, of which 66 met the inclusion criteria after summaries were read. For drafting this article, the following sub-themes were proposed: getting ready to travel with children; knowing some of the transfer risks (air, land and water transportation) and exploring the destination with children (sun exposure, accommodations, altitude, food, traveler's diarrhea, insect bites) and return from the trip with children. Over the years, there has been an increase in the number of children who travel around the world. However, this population is still subject to health problems while traveling and may be even more susceptible than the adult age group. These problems arise from a variety of factors, including exposure to infectious organisms, the use of certain types of transportation, and participation in some activities, such as hiking at high altitudes, among others. However, when traveling with children, these risk factors can be overlooked; a trip that is considered safe for an adult might not be a good choice for this age group. The pediatric consultation should be a good opportunity to optimize preventive guidelines at the pre-trip planning. Copyright © 2015 Sociedade Brasileira de Pediatria. Published by Elsevier Editora Ltda. All rights reserved.

Children as passengers in automobiles: the neglected minority on the nation's highways.

Science.gov (United States)

Shelness, A; Charles, S

1975-08-01

The federal government is urging states to enact legislation requiring that safety belts be worn. Small children are excluded from this requirement. Following the neonatal period, the motor vehicle poses the greatest single threat to a child's life. Contrary to popular belief, more small children are killed and injured inside the vehicle than outside. The marjority of children now ride in cars unprotected or inadequately protected. Standard safety belts are unsuitable for small children. Special devices capable of distributing collision forces over a large body area should be used. Original children's car "safety" seats were not intended to protect their occupants in a crash. These seats became subject to a government safety standard in April 1971. Shortly after this standard came into effect it was shown to be grossly inadequate in ensuring crash protection. A proposal for revising current safety criteria was issued in March 1974--to be implemented in September 1975. A number of progressive companies have developed crashworthy devices. As public awareness is being awakened, manufacturers are begining to find that "safety" sells. Child crash protection has not escaped the attention of safety experts whose writings are reviewed, but it is shown that lack of parent awareness and concern can be directly related to sparse and often inaccurate and incomplete information available. Many popular child care books ignore the subject entirely. Because correct use of devices is of such critical importance, instructions detailing what parents must do should be prominently displayed on a permanent label attached to the device. Observation of car seats in use confirms that correct installation of the device itself and/or proper securement of the child within the device in the exception rather than the rule. The development of child restraints is of recent date. It is essential to keep abreast of advances made in the field. Earlier recommendations may be superseded by more recent

Experimental verification of numerical calculations of railway passenger seats

Science.gov (United States)

Ligaj, B.; Wirwicki, M.; Karolewska, K.; Jasińska, A.

2018-04-01

The construction of railway seats is based on industry regulations and the requirements of end users, i.e. passengers. The two main documents in this context are the UIC 566 (3rd Edition, dated 7 January 1994) and the EN 12663-1: 2010+A1:2014. The study was to carry out static load tests of passenger seat frames. The paper presents the construction of the test bench and the results of experimental and numerical studies of passenger seat rail frames. The test bench consists of a frame, a transverse beam, two electric cylinders with a force value of 6 kN, and a strain gauge amplifier. It has a modular structure that allows for its expansion depending on the structure of the seats. Comparing experimental results with numerical results for points A and B allowed to determine the existing differences. It follows from it that higher stress values are obtained by numerical calculations in the range of 0.2 MPa to 35.9 MPa.

Biomechanical investigation of prolonged driving in an ergonomically designed truck seat prototype.

Science.gov (United States)

Cardoso, Michelle; McKinnon, Colin; Viggiani, Dan; Johnson, Michel J; Callaghan, Jack P; Albert, Wayne J

2018-03-01

A postural evaluation during a prolonged driving task was conducted to determine the ergonomic validity of a new freely adjustable truck seat prototype. Twenty participants were recruited to perform two 2-h simulated driving sessions. Postures were assessed using motion capture, accelerometers and pressure pads. Subjective discomfort was also monitored in 15-min increments using ratings of perceived discomfort (RPD) and the Automotive Seating Discomfort Questionnaire. Participants had a more neutral spine posture during the first hour of the drive and reported lower RPDs while sitting in the prototype. Pairing the gluteal backrest panel with the adjustable seat pan helped reduce the average sitting pressure. The industry-standard truck seat may lead to the development of poor whole body posture, and the proposed ergonomic redesign of a new truck seat helped improve sitting posture and reduce perceived discomfort. Practitioner Summary: A new freely adjustable truck seat prototype was compared to an Industry standard seat to assess hypothesised improvements to sitting posture and discomfort for long haul driving. It was found that the adjustable panels in the prototype helped promote spine posture, reduce sitting pressure and improved discomfort ratings.

Utilização de assentos de segurança por crianças matriculadas em creches Utilización de asientos de seguridad por niños matriculados en guarderías Child safety restraint use among children attending day care centers

Directory of Open Access Journals (Sweden)

Sergio Ricardo Lopes de Oliveira

2009-10-01

-sectional study using a stratified sampling conducted in the city of Maringá, Southern Brazil, between March and May 2007. Each day care center was visited at one day only. The outcome was use of child safety restraints by children under four. Vehicles (N=301 driving children under four were approached and information was collected using semi-structured questionnaires. Variables regarding child and adult seat distribution, use of safety restraints by occupants and driver's gender were analyzed. Data analyses included Fisher's exact test, Mantel-Haenszel chi-square test, and logistic regression. RESULTS: Of the drivers approached, 51.8% were using seat belts (60.4% among women, 44.9% among men. Among children, 36.1% were using child safety seats, 45.4% were unrestrained during traveling, 16.0% were seated on an adult lap, and 2.7% were using seat belts. The logistic regression showed the following factors affecting child safety restraint use: child age under 15 months (OR = 3.76; seat belt use by the driver (OR = 2.45; and children from socio-occupational condition with higher income and education (OR = 1.37. CONCLUSIONS: Child safety restraint use was associated to child age, seat belt use by the driver, and socio-occupational condition of day care centers. The finding of low rates of child safety restraint use poses a challenge to preventive medicine in Brazil, requiring attention and action to promote its widespread use.

75 FR 58340 - Airworthiness Directives; Koito Industries, Ltd., Seats and Seating Systems Approved Under...

Science.gov (United States)

2010-09-24

... under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States... cable, hook and loop (hook and loop is a generic term for Velcro), leather cover that is glued to seat...

Seat Adjustment Design of an Intelligent Robotic Wheelchair Based on the Stewart Platform

Directory of Open Access Journals (Sweden)

Po Er Hsu

2013-03-01

Full Text Available A wheelchair user makes direct contact with the wheelchair seat, which serves as the interface between the user and the wheelchair, for much of any given day. Seat adjustment design is of crucial importance in providing proper seating posture and comfort. This paper presents a multiple-DOF (degrees of freedom seat adjustment mechanism, which is intended to increase the independence of the wheelchair user while maintaining a concise structure, light weight, and intuitive control interface. This four-axis Stewart platform is capable of heaving, pitching, and swaying to provide seat elevation, tilt-in-space, and sideways movement functions. The geometry and types of joints of this mechanism are carefully arranged so that only one actuator needs to be controlled, enabling the wheelchair user to adjust the seat by simply pressing a button. The seat is also equipped with soft pressure-sensing pads to provide pressure management by adjusting the seat mechanism once continuous and concentrated pressure is detected. Finally, by comparing with the manual wheelchair, the proposed mechanism demonstrated the easier and more convenient operation with less effort for transfer assistance.

Factors related to seatbelt-wearing among rear-seat passengers in Malaysia.

Science.gov (United States)

Ng, Choy Peng; Law, Teik Hua; Wong, Shaw Voon; Kulanthayan, S

2013-01-01

The benefit of wearing a rear seatbelt in reducing the risk of motor vehicle crash-related fatalities and injuries has been well documented in previous studies. Wearing a seatbelt not only reduces the risk of injury to rear-seat passengers, but also reduces the risk of injury to front-seat occupant who could be crushed by unbelted rear-seat passengers in a motor vehicle crash. Despite the benefits of wearing a rear seatbelt, its rate of use in Malaysia is generally low. The objective of this study was to identify factors that are associated with the wearing of a seatbelt among rear-seat passengers in Malaysia. Multinomial logistic regression analysis of the results of a questionnaire survey of 1651 rear-seat passengers revealed that rear-seat passengers who were younger, male, single and less educated and who had a perception of a low level of legislation enforcement, a lower risk-aversion and less driving experience (only for passengers who are also drivers) were less likely to wear a rear seatbelt. There was also a significant positive correlation between driver seatbelt and rear seatbelt-wearing behaviour. This implies that, in regards to seatbelt-wearing behaviour, drivers are more likely to adopt the same seatbelt-wearing behaviour when travelling as rear-seat passengers as they do when driving. These findings are crucial to the development of new interventions to increase the compliance rate of wearing a rear seatbelt. Copyright © 2012 Elsevier Ltd. All rights reserved.

Physiological Motion Axis for the Seat of a Dynamic Office Chair

Science.gov (United States)

Kuster, Roman Peter; Bauer, Christoph Markus; Oetiker, Sarah; Kool, Jan

2016-01-01

Objective The aim of this study was to determine and verify the optimal location of the motion axis (MA) for the seat of a dynamic office chair. Background A dynamic seat that supports pelvic motion may improve physical well-being and decrease the risk of sitting-associated disorders. However, office work requires an undisturbed view on the work task, which means a stable position of the upper trunk and head. Current dynamic office chairs do not fulfill this need. Consequently, a dynamic seat was adapted to the physiological kinematics of the human spine. Method Three-dimensional motion tracking in free sitting helped determine the physiological MA of the spine in the frontal plane. Three dynamic seats with physiological, lower, and higher MA were compared in stable upper body posture (thorax inclination) and seat support of pelvic motion (dynamic fitting accuracy). Spinal kinematics during sitting and walking were compared. Results The physiological MA was at the level of the 11th thoracic vertebra, causing minimal thorax inclination and high dynamic fitting accuracy. Spinal motion in active sitting and walking was similar. Conclusion The physiological MA of the seat allows considerable lateral flexion of the spine similar to walking with a stable upper body posture and a high seat support of pelvic motion. Application The physiological MA enables lateral flexion of the spine, similar to walking, without affecting stable upper body posture, thus allowing active sitting while focusing on work. PMID:27150530

Self-reported seat discomfort among Dutch commercial truck drivers

NARCIS (Netherlands)

Tan, C.F.; Chen, W.; Rauterberg, G.W.M.

2010-01-01

Comfort is an attribute that today’s consumers demand more and more. The seat has an important role to play in fulfilling these comfort expectations. Seating comfort is a major concern for drivers and other members of the work force who are exposed to extended periods of sitting and its associated

Personality and Politics: The Untold Story of Robert S. McNamara and Curtis E. Lemay

Science.gov (United States)

2012-06-01

against the shiny stove fender, while the frost snapped and crackled outside. The larder was a vague mystery which Pop didn’t bother to penetrate...their aircraft to fill out forms, grab food and refill coffee . In addition, he found the offloading of coal to be a complex and challenging task...issue of auto safety and the use of seat belts. In that hearing, John O. Moore, who had completed Automotive Crash Injury Research at Cornell

Development of adaptive helicopter seat systems for aircrew vibration mitigation

Science.gov (United States)

Chen, Yong; Wickramasinghe, Viresh; Zimcik, David G.

2008-03-01

Helicopter aircrews are exposed to high levels of whole body vibration during flight. This paper presents the results of an investigation of adaptive seat mount approaches to reduce helicopter aircrew whole body vibration levels. A flight test was conducted on a four-blade helicopter and showed that the currently used passive seat systems were not able to provide satisfactory protection to the helicopter aircrew in both front-back and vertical directions. Long-term exposure to the measured whole body vibration environment may cause occupational health issues such as spine and neck strain injuries for aircrew. In order to address this issue, a novel adaptive seat mount concept was developed to mitigate the vibration levels transmitted to the aircrew body. For proof-of-concept demonstration, a miniature modal shaker was properly aligned between the cabin floor and the seat frame to provide adaptive actuation authority. Adaptive control laws were developed to reduce the vibration transmitted to the aircrew body, especially the helmet location in order to minimize neck and spine injuries. Closed-loop control test have been conducted on a full-scale helicopter seat with a mannequin configuration and a large mechanical shaker was used to provide representative helicopter vibration profiles to the seat frame. Significant vibration reductions to the vertical and front-back vibration modes have been achieved simultaneously, which verified the technical readiness of the adaptive mount approach for full-scale flight test on the vehicle.

The repeatability and reproducibility of the BioRID IIg in a repeatable laboratory seat based on a production car seat.

Science.gov (United States)

Hynd, David; Depinet, Paul; Lorenz, Bernd

2013-01-01

The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx . However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My . The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was

Rural roadway safety perceptions among rural teen drivers living in and outside of towns.

Science.gov (United States)

Ramirez, Marizen; Roth, Lisa; Young, Tracy; Peek-Asa, Corinne

2013-01-01

To compare perceptions about rural road and general driving behaviors between teens who live in- and out-of-town from rural communities in Iowa. A cross-sectional survey was conducted with 160 teens anticipating their Intermediate License within 3 months upon enrollment into this study. Self-administered surveys were used to collect demographics and driving exposures (eg, frequency of driving, age when first drove unsupervised). Two Likert scales were included to measure agreement with safe driving behaviors on rural roads and general safe driving behaviors (eg, speeding, seat belt use). T-tests were calculated comparing mean composite scores between in- and out-of-town teens, and between mean rural road and general driving safety attitude scores. A linear regression multivariable model was constructed to identify predictors of the rural road score. While the majority of teens endorsed rural road and general safe driving behaviors, up to 40% did not. Thirty-two percent did not believe the dangers of animals on rural roads, and 40% disagreed that exceeding the speed limit is dangerous. In-town teens were less safety conscious about rural road hazards with a significantly lower mean composite score (4.4) than out-of-town teens (4.6); mean scores for general driving behaviors were similar. Living out-of-town and owning one's own car were significant predictors of increased rural road safety scores. Rural, in-town teens have poorer safety attitudes about rural roadway hazards compared with out-of-town teens. Interventions that involve education, parental supervision, and practice on rural roads are critical for preventing teen crashes on rural roads. No claim to original US government works.

76 FR 18042 - Uniform Criteria for State Observational Surveys of Seat Belt Use

Science.gov (United States)

2011-04-01

... Transportation (MO DOT), Nevada Department of Public Safety (prepared by University of Nevada--Las Vegas) (NV DPS... member of the public stated that conducting such surveys is a waste of taxpayer's money. (Jean Public at...; WY HSP at 1; LA HSC at 1; NJIT at 3; CO DOT at 1; GHSA at 1; ODU at 1- 2; MO DOT at 1; CA OTS at 1...

Analysis of factors associated with traffic injury severity on rural roads in Iran.

Science.gov (United States)

Kashani, Ali Tavakoli; Shariat-Mohaymany, Afshin; Ranjbari, Andishe

2012-01-01

Iran is a country with one of the highest rates of traffic crash fatality and injury, and seventy percent of these fatalities happen on rural roads. The objective of this study is to identify the significant factors influencing injury severity among drivers involved in crashes on two kinds of major rural roads in Iran: two-lane, two-way roads and freeways. According to the dataset, 213569 drivers were involved in rural road crashes in Iran, over the 3 years from 2006 to 2008. The Classification And Regression Tree method (CART) was applied for 13 independent variables, and one target variable of injury severity with 3 classes of no-injury, injury and fatality. Some of the independent variables were cause of crash, collision type, weather conditions, road surface conditions, driver's age and gender and seat belt usage. The CART model was trained by 70% of these data, and tested with the rest. It was indicated that seat belt use is the most important safety factor for two-lane, two-way rural roads, but on freeways, the importance of this variable is less. Cause of crash, also turned out to be the next most important variable. The results showed that for two-lane, two-way rural roads, "improper overtaking" and "speeding", and for rural freeways, "inattention to traffic ahead", "vehicle defect", and "movement of pedestrians, livestock and unauthorized vehicles on freeways" are the most serious causes of increasing injury severity. The analysis results revealed seat belt use, cause of crash and collision type as the most important variables influencing the injury severity of traffic crashes. To deal with these problems, intensifying police enforcement by means of mobile patrol vehicles, constructing overtaking lanes where necessary, and prohibiting the crossing of pedestrians and livestock and the driving of unauthorized vehicles on freeways are necessary. Moreover, creating a rumble strip on the two edges of roads, and paying attention to the design consistency of

VERO cells harbor a poly-ADP-ribose belt partnering their epithelial adhesion belt

Directory of Open Access Journals (Sweden)

Laura Lafon-Hughes

2014-10-01

Full Text Available Poly-ADP-ribose (PAR is a polymer of up to 400 ADP-ribose units synthesized by poly-ADP-ribose-polymerases (PARPs and degraded by poly-ADP-ribose-glycohydrolase (PARG. Nuclear PAR modulates chromatin compaction, affecting nuclear functions (gene expression, DNA repair. Diverse defined PARP cytoplasmic allocation patterns contrast with the yet still imprecise PAR distribution and still unclear functions. Based on previous evidence from other models, we hypothesized that PAR could be present in epithelial cells where cadherin-based adherens junctions are linked with the actin cytoskeleton (constituting the adhesion belt. In the present work, we have examined through immunofluorescence and confocal microscopy, the subcellular localization of PAR in an epithelial monkey kidney cell line (VERO. PAR was distinguished colocalizing with actin and vinculin in the epithelial belt, a location that has not been previously reported. Actin filaments disruption with cytochalasin D was paralleled by PAR belt disruption. Conversely, PARP inhibitors 3-aminobenzamide, PJ34 or XAV 939, affected PAR belt synthesis, actin distribution, cell shape and adhesion. Extracellular calcium chelation displayed similar effects. Our results demonstrate the existence of PAR in a novel subcellular localization. An initial interpretation of all the available evidence points towards TNKS-1 as the most probable PAR belt architect, although TNKS-2 involvement cannot be discarded. Forthcoming research will test this hypothesis as well as explore the existence of the PAR belt in other epithelial cells and deepen into its functional implications.

The transmission of vertical vibration through seats: Influence of the characteristics of the human body

Science.gov (United States)

Toward, Martin G. R.; Griffin, Michael J.

2011-12-01

The transmission of vibration through a seat depends on the impedance of the seat and the apparent mass of the seat occupant. This study was designed to determine how factors affecting the apparent mass of the body (age, gender, physical characteristics, backrest contact, and magnitude of vibration) affect seat transmissibility. The transmission of vertical vibration through a car seat was measured with 80 adults (41 males and 39 females aged 18-65) at frequencies between 0.6 and 20 Hz with two backrest conditions (no backrest and backrest), and with three magnitudes of random vibration (0.5, 1.0, and 1.5 m s -2 rms). Linear regression models were used to study the effects of subject physical characteristics (age, gender, and anthropometry) and features of their apparent mass (resonance frequency, apparent mass at resonance and at 12 Hz) on the measured seat transmissibility. The strongest predictor of both the frequency of the principal resonance in seat transmissibility and the seat transmissibility at resonance was subject age, with other factors having only marginal effects. The transmissibility of the seat at 12 Hz depended on subject age, body mass index, and gender. Although subject weight was strongly associated with apparent mass, weight was not strongly associated with seat transmissibility. The resonance frequency of the seat decreased with increases in the magnitude of the vibration excitation and increased when subjects made contact with the backrest. Inter-subject variability in the resonance frequency and transmissibility at resonance was less with greater vibration excitation, but was largely unaffected by backrest contact. A lumped parameter seat-person model showed that changes in seat transmissibility with age can be predicted from changes in apparent mass with age, and that the dynamic stiffness of the seat appeared to increase with increased loading so as to compensate for increases in subject apparent mass associated with increased sitting

Restraint use and seating position among children in motor vehicles ...

African Journals Online (AJOL)

Just over a third of the children were seated on the front seat of the vehicle, ... meaning adult will be dislodged by the huge gravitational forces in the case of an ..... action. 2009. http://whqlibdoc.who.int/publications/2009/9789241563840_.

Identifying strategies to improve the effectiveness of booster seat laws

Science.gov (United States)

2008-05-01

The objective of this project was to identify strategies to improve the effectiveness of booster seat laws. The project explored the possible factors that relate to the use and nonuse of booster seats, and examined the attitudes of law enforcement of...

Adaptive magnetorheological seat suspension for the expeditionary fighting vehicle

International Nuclear Information System (INIS)

Hiemenz, G J; Hu, W; Wereley, N M

2009-01-01

The Expeditionary Fighting Vehicle (EFV) is an amphibious vehicle designed to operate through harsh conditions and at much higher speeds than its predecessors. These unique capabilities and broadly varying operational conditions lead to a complex design and human factors scenario for the forward seating positions that cannot be solved using conventional passive seat suspension systems. Injurious shock loads transmitted to the occupants when traversing over water in high sea states and/or at high speeds, as well as harmful shock and vibration transmitted to the occupants when the vehicle is travelling over land, pose a threat to occupant health and significantly limit mission duration. In this study, a semi-active magnetorheological (MR) seat suspension is developed which adapts to broadly varying operational conditions, as well as occupant weight, to provide optimal protection of EFV occupants. It is shown that this MR seat suspension system will reduce the shock and vibration transmitted to the occupant by up to 33% and 65%, respectively, as compared to the existing passive suspension.

Adaptive magnetorheological seat suspension for the expeditionary fighting vehicle

Energy Technology Data Exchange (ETDEWEB)

Hiemenz, G J [Techno-Sciences, Inc., 11750 Beltsville Dr. Ste. 300, Beltsville, MD 20705 (United States); Hu, W; Wereley, N M [Aerospace Engineering, University of Maryland, College Park, MD 20712 (United States)], E-mail: greg@technosci.com, E-mail: wereley@umd.edu

2009-02-01

The Expeditionary Fighting Vehicle (EFV) is an amphibious vehicle designed to operate through harsh conditions and at much higher speeds than its predecessors. These unique capabilities and broadly varying operational conditions lead to a complex design and human factors scenario for the forward seating positions that cannot be solved using conventional passive seat suspension systems. Injurious shock loads transmitted to the occupants when traversing over water in high sea states and/or at high speeds, as well as harmful shock and vibration transmitted to the occupants when the vehicle is travelling over land, pose a threat to occupant health and significantly limit mission duration. In this study, a semi-active magnetorheological (MR) seat suspension is developed which adapts to broadly varying operational conditions, as well as occupant weight, to provide optimal protection of EFV occupants. It is shown that this MR seat suspension system will reduce the shock and vibration transmitted to the occupant by up to 33% and 65%, respectively, as compared to the existing passive suspension.

Effects of Wheelchair Seat-height Settings on Alternating Lower Limb Propulsion With Both Legs.

Science.gov (United States)

Murata, Tomoyuki; Asami, Toyoko; Matsuo, Kiyomi; Kubo, Atsuko; Okigawa, Etsumi

2014-01-01

This study investigated the effects of seat-height settings of wheelchairs with alternating propulsion with both legs. Seven healthy individuals with no orthopedic disease participated. Flexion angles at initial contact (FA-IC) of each joint, range of motion during propulsion period (ROM-PP), and ground reaction force (GRF) were measured using a three dimensional motion capture system and force plates, and compared with different seat-height settings. Statistically significant relationships were found between seat-height and speed, stride length, knee FA-IC, ankle FA-IC, hip ROM-PP, vertical ground reaction force (VGRF), and anterior posterior ground reaction force (APGRF). Speed, hip ROM-PP, VGRF and APGRF increased as the seat-height was lowered. This effect diminished when the seat-height was set below -40 mm. VGRF increased as the seat-height was lowered. The results suggest that the seat-height effect can be attributed to hip ROM-PP; therefore, optimal foot propulsion cannot be achieved when the seat height is set either too high or too low. Efficient foot propulsion of the wheelchair can be achieved by setting the seat height to lower leg length according to a combination of physical characteristics, such as the user's physical functions, leg muscles, and range of motion.

Pelvic belt effects on sacroiliac joint ligaments: a computational approach to understand therapeutic effects of pelvic belts.

Science.gov (United States)

Sichting, Freddy; Rossol, Jerome; Soisson, Odette; Klima, Stefan; Milani, Thomas; Hammer, Niels

2014-01-01

The sacroiliac joint is a widely described source of low back pain. Therapeutic approaches to relieve pain include the application of pelvic belts. However, the effects of pelvic belts on sacroiliac joint ligaments as potential pain generators are mostly unknown. The aim of our study was to analyze the influence of pelvic belts on ligament load by means of a computer model. Experimental computer study using a finite element method. A computer model of the human pelvis was created, comprising bones, ligaments, and cartilage. Detailed geometries, material properties of ligaments, and in-vivo pressure distribution patterns of a pelvic belt were implemented. The effects of pelvic belts on ligament strain were computed in the double-leg stance. Pelvic belts increase sacroiliac joint motion around the sagittal axis but decrease motion around the transverse axis. With pelvic belt application, most of the strained sacroiliac joint ligaments were relieved, especially the sacrospinous, sacrotuberous, and the interosseous sacroiliac ligaments. Sacroiliac joint motion and ligament strains were minute. These results agree with validation data from other studies. Assigning homogenous and linear material properties and excluding muscle forces are clear simplifications of the complex reality. Pelvic belts alter sacroiliac joint motion and provide partial relief of ligament strain that is subjectively marked, although minimal in absolute terms. These findings confirm theories that besides being mechanical stabilizers, the sacroiliac joint ligaments are likely involved in neuromuscular feedback mechanisms. The results from our computer model help with unraveling the therapeutic mechanisms of pelvic belts.

30 CFR 57.4503 - Conveyor belt slippage.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Conveyor belt slippage. 57.4503 Section 57.4503... Control Installation/construction/maintenance § 57.4503 Conveyor belt slippage. (a) Surface belt conveyors...) Underground belt conveyors shall be equipped with a detection system capable of automatically stopping the...

Investigation of a new type charging belt

International Nuclear Information System (INIS)

Jones, N.L.

1994-01-01

There are many desirable characteristics for an electrostatic accelerator charging belt. An attempt has been made to find a belt that improves on these properties over the stock belt. Results of the search, procurement, and 1,500 hours of operational experience with a substantially different belt are reported

SIT (seated immobility thromboembolism) syndrome: a 21st century lifestyle hazard.

Science.gov (United States)

Beasley, Richard; Heuser, Patricia; Raymond, Nigel

2005-04-01

The association between prolonged seated immobility and venous thromboembolism (VTE) is well recognised in relation to travel. In this case series, we report the occurrence of deep vein thrombosis (DVT) or pulmonary embolism (PE) following prolonged sitting in relation to work and/or recreation. The cases were characterised by the considerable length of time the individuals sat, the extensive nature of the VTE events in young individuals without other recognised risk factors, and the lack of recognition by the attending doctors of seated immobility as the likely major risk factor. While recognising that the association may be coincidental rather than causal, we propose the acronym 'SIT' (seated immobility thromboembolism) syndrome to encompass all forms of seated immobility associated with VTE.

Belt for picking up liquids

Energy Technology Data Exchange (ETDEWEB)

Sewell, R B.H.; Nelson, S P

1973-05-18

This belt for picking up liquids consists of a layer of strong material, e.g., coarse cloth, sewed on at least one layer of absorbing material, e.g., sponge cloth, the stitching being disposed along chevrons with their apexes along the central axis of the belt; the edges do not contain any other marks. This arrangement facilitates the expulsion of the absorbed liquid when the belt passes between compression rollers.

30 CFR 56.4503 - Conveyor belt slippage.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Conveyor belt slippage. 56.4503 Section 56.4503... Control Installation/construction/maintenance § 56.4503 Conveyor belt slippage. Belt conveyors within... shall attend the belt at the drive pulley when it is necessary to operate the conveyor while temporarily...

Persistence of Salmonella on egg conveyor belts is dependent on the belt type but not on the rdar morphotype.

Science.gov (United States)

Stocki, S L; Annett, C B; Sibley, C D; McLaws, M; Checkley, S L; Singh, N; Surette, M G; White, A P

2007-11-01

Commercial caged layer flocks in Alberta, Canada, are commonly monitored for Salmonella enterica serovar Enteritidis (SE) and S. enterica serovar Typhimurium (ST) by environmental sampling. In one recent case, a SE strain isolated from the egg conveyor belt was a source of persistent infection for the flock. This study was undertaken to examine Salmonella colonization on egg conveyor belts and to determine whether the rdar morphotype, a conserved physiology associated with aggregation and long-term survival, contributed to persistence. Four woven belts constructed of natural or nonnatural fibers and a 1-piece belt made of vinyl were tested with rdar-positive ST and SE strains and a rdar-negative ST DeltaagfD reference strain. The type of egg belt was the most important factor influencing Salmonella colonization and persistence. The vinyl belt, with the least surface area available for colonization, had the fewest Salmonella remaining after washing and disinfection, whereas the hemp-plastic belt, with the greatest surface area, had the most Salmonella remaining. Real-time gene expression indicated that the rdar morphotype was involved in colonizing the egg belt pieces; however, it was not essential for persistence. In addition, rdar-positive and rdar-negative strains were equally similarly to disinfection on the egg belt pieces. The results indicate that Salmonella can persist on a variety of egg belts by mechanisms other than the rdar morphotype, and that using egg conveyer belts with reduced surface area for bacterial colonization can lessen contamination problems.

Granulite belts of Central India with special reference to the Bhopalpatnam Granulite Belt: Significance in crustal evolution and implications for Columbia supercontinent

Science.gov (United States)

Vansutre, Sandeep; Hari, K. R.

2010-11-01

The Central Indian collage incorporates the following major granulite belts: (1) the Balaghat-Bhandara Granulite Belt (BBG), (2) the Ramakona-Katangi Granulite Belt (RKG), (3) the Chhatuabhavna Granulite (CBG) of Bilaspur-Raigarh Belt, (4) the Makrohar Granulite Belt (MGB) of Mahakoshal supracrustals, (5) the Kondagaon Granulite Belt (KGGB), (6) the Bhopalpatnam Granulite Belt (BGB), (7) the Konta Granulite Belt (KTGB) and (8) the Karimnagar Granulite Belt (KNGB) of the East Dharwar Craton (EDC). We briefly synthesize the general geologic, petrologic and geochronologic features of these belts and explain the Precambrian crustal evolution in Central India. On the basis of the available data, a collisional relationship between Bastar craton and the EDC during the Paleo-Mesoproterozoic is reiterated as proposed by the earlier workers. The tectonic evolution of only few of the orogenic belts (BGB in particular) of Central India is related to Columbia.

Materials for fire resistant passenger seats in aircraft

Science.gov (United States)

Tesoro, G.; Moussa, A.

1980-01-01

The paper considers the selection of cushioning foam and upholstery fabric materials for aircraft passenger seats. Polyurethane, polychloroprene, polyimide, and polyphosphazene are the foam materials considered; and a variety of commercial and developmental fabrics (including wool, cotton, synthetics, and blends) are examined. Viable approaches to the design of fire-resistant seat assemblies are indicated. Results of an experimental laboratory study of fabrics and fabric/foam assemblies exposed to external point-source radiative heat flux are discussed.

Fire-resistant materials for aircraft passenger seat construction

Science.gov (United States)

Fewell, L. L.; Tesoro, G. C.; Moussa, A.; Kourtides, D. A.

1979-01-01

The thermal response characteristics of fabric and fabric-foam assemblies are described. The various aspects of the ignition behavior of contemporary aircraft passenger seat upholstery fabric materials relative to fabric materials made from thermally stable polymers are evaluated. The role of the polymeric foam backing on the thermal response of the fabric-foam assembly is also ascertained. The optimum utilization of improved fire-resistant fabric and foam materials in the construction of aircraft passenger seats is suggested.

The Influence of Tractor-Seat Height above the Ground on Lateral Vibrations

Directory of Open Access Journals (Sweden)

Jaime Gomez-Gil

2014-10-01

Full Text Available Farmers experience whole-body vibrations when they drive tractors. Among the various factors that influence the vibrations to which the driver is exposed are terrain roughness, tractor speed, tire type and pressure, rear axle width, and tractor seat height above the ground. In this paper the influence of tractor seat height above the ground on the lateral vibrations to which the tractor driver is exposed is studied by means of a geometrical and an experimental analysis. Both analyses show that: (i lateral vibrations experienced by a tractor driver increase linearly with tractor-seat height above the ground; (ii lateral vibrations to which the tractor driver is exposed can equal or exceed vertical vibrations; (iii in medium-size tractors, a feasible 30 cm reduction in the height of the tractor seat, which represents only 15% of its current height, will reduce the lateral vibrations by around 20%; and (iv vertical vibrations are scarcely influenced by tractor-seat height above the ground. The results suggest that manufacturers could increase the comfort of tractors by lowering tractor-seat height above the ground, which will reduce lateral vibrations.

Musculoskeletal analysis of driving fatigue: The influence of seat adjustments

DEFF Research Database (Denmark)

Majid, Noor Aliah binti Abdul; Abdullah, Mohd Fareez Edzuan; Jamaludin, Mohd Syahmi

2013-01-01

Main causes for discomfort experienced by vehicle drivers during driving were investigated using a rigid-body model originally developed in the AnyBody Modeling System [1]. The interactions between the human body and the car-seat in various combinations of seat-pan/backrest inclinations and the e...

An Active Seat Controller with Vehicle Suspension Feedforward and Feedback States: An Experimental Study

Directory of Open Access Journals (Sweden)

Abdulaziz Alfadhli

2018-04-01

Full Text Available Active seat suspensions can be used to reduce the harmful vertical vibration of a vehicle’s seat by applying an external force using a closed loop controller. Many of the controllers found in the literature are difficult to implement practically, because they are based on using unavailable or difficult and costly measurements. This paper presents both simulation and experimental studies of five novel, simple, and cost-effective control strategies to be used for an active seat suspension in order to improve ride comfort at low frequencies below 20 Hz. These strategies use available and measurable feedforward (preview information states from the vehicle secondary suspension, as well as feedback states from the seat suspension, together with gains optimised to minimise the occupant vibration. The gains were optimised using a genetic algorithm (GA, with a fitness function based on the seat effective amplitude transmissibility (SEAT factor. Constraints on the control force and the seat suspension stroke were also included in the optimisation algorithm. Simulation and laboratory experimental tests were carried out to assess the performance of the proposed controllers according to the ISO 2631-1 standard, in both the frequency and time domains with a range of different road profiles. The experimental tests were performed using a multi-axis simulation table (MAST and a physical active seat suspension configured as a hardware-in-loop (HIL simulation with a virtual linear quarter vehicle model (QvM. The results demonstrate that the proposed controllers substantially attenuate the vertical vibration at the driver’s seat compared with both a passive and a proportional-integral-derivative (PID active seat suspension and thus improve ride comfort together with reducing vibration-linked health risks. Moreover, experimental results show that employing both feedforward information and feedback vehicle body and seat acceleration signals in the controller

Airline seat inventory control benefiting from currency differentials to enhance revenues

Directory of Open Access Journals (Sweden)

C.E. Love

2003-12-01

Full Text Available The purpose of this paper is to develop an airline seat inventory control model which will capitalise on currency differentials that exist between city pairs. The approach taken here is to maximise Expected Marginal Seat Revenues as proposed by Belobaba for non-nested fare classes. the basic Expected Marginal Seat Revenue model is extended to explicitly include the effects of overbooking. Data from the South African Airways return flight between Cape Town and London is utilised to demonstrate the model.

Development of Methodology to Gather Seated Anthropometry Data in a Microgravity Environment

Science.gov (United States)

Rajulu, Sudhakar; Young, Karen; Mesloh, Miranda

2010-01-01

The Constellation Program is designing a new vehicle based off of new anthropometric requirements. These requirements specify the need to account for a spinal elongation factor for anthropometric measurements involving the spine, such as eye height and seated height. However, to date there is no data relating spinal elongation to a seated posture. Only data relating spinal elongation to stature has been collected in microgravity. Therefore, it was proposed to collect seated height in microgravity to provide the Constellation designers appropriate data for their analyses. This document will describe the process in which the best method to collect seated height in microgravity was developed.

Concordancia entre dos observadores en la medición del consumo de tabaco y del uso del cinturón de seguridad y del teléfono móvil en vehículos Agreement between two observers in the measurement of smoking and use of safety belt and cell phones in vehicles

Directory of Open Access Journals (Sweden)

José M. Martínez-Sánchez

2012-02-01

Full Text Available El objetivo de este trabajo es evaluar la factibilidad de realizar observaciones directas del consumo de tabaco y del uso del cinturón de seguridad y del teléfono móvil del conductor del vehículo en la ciudad de Barcelona, así como analizar el grado de concordancia entre dos observadores. Se realizaron 315 pares de observaciones. El porcentaje simple de concordancia interobservador de las variables consumo de tabaco del conductor y de los pasajeros fue del 100%, con un índice Kappa de 1,0. También se obtuvo la máxima concordancia interobservador en la medición del uso del teléfono móvil y del número de pasajeros menores de 14 años. La variable con menor concordancia fue la edad del conductor. En conclusión, los estudios mediante observación directa se muestran como un buen recurso para monitorizar el consumo de tabaco, el uso del cinturón de seguridad y el uso del teléfono móvil del conductor del vehículo.The aim of this study was to assess the feasibility of direct observations of smoking and use of seat belts and cell phones in drivers in the city of Barcelona, and to analyze the agreement between two observers. We performed 315 pairs of observations. The simple percentage inter-observer agreement between driver and passenger smoking was 100% with a Kappa coefficient=1.0. There was high inter-observer agreement in measurement of cell phone use and the number of passengers aged less than 14 years old. The variable with the lowest agreement was the driver's age. In conclusion, direct observation studies are a good resource for monitoring smoking and use of seat belts and cell phones in the drivers of motor vehicles.

Design Method for Fast Switching Seat Valves for Digital Displacement Machines

DEFF Research Database (Denmark)

Roemer, Daniel Beck; Johansen, Per; Pedersen, Henrik C.

2014-01-01

corresponding to the piston movement, which has been shown to facilitate superior part load efficiency combined with high bandwidth compared to traditional displacement machines. However, DD machines need fast switching on-off valves with low pressure loss for efficient operation, especially in fast rotating......Digital Displacement (DD) machines are upcoming technology where the displacement of each pressure chamber is controlled electronically by use of two fast switching seat valves. The effective displacement and operation type (pumping/motoring) may be controlled by manipulating the seat valves...... method for DD seat valves are presented, taking into account the significant aspects related to obtaining efficient DD valves with basis in a given DD machine specifications. The seat area is minimized and the stroke length is minimized to obtain fast switching times while considering the pressure loss...

The seating mechanics of head-neck modular tapers in vitro: Load-displacement measurements, moisture, and rate effects.

Science.gov (United States)

Ouellette, Eric S; Shenoy, Aarti A; Gilbert, Jeremy L

2018-04-01

The mechanically assisted crevice corrosion performance of head-neck modular tapers is a significant concern in orthopedic biomaterials. Fretting crevice corrosion processes in modular tapers are thought to be influenced by a wide array of factors including seating mechanics of the junction, hence there is a need for in vitro test methods that can assess their performance. This study presented a test method to directly measure the load-displacement seating mechanics of modular tapers and used this method to compare the seating mechanics for different tapers, moisture, seating loads and seating rates. Seating mechanics were explored whereby the instantaneous load-displacement behavior of the head seating onto the neck is captured and used to define the mechanics of seating. Two distinct taper design/material combinations were assembled wet or dry using axially applied loads (500, 1,000, 2,000, and 4,000 N) at two loading rates of 100 and 10 4  N/s (n = 5 for each condition) using a servohydraulic test frame. The results showed that pull-off strength scaled with seating load and ranged between 43% and 68% of seating load depending on sample and wetness. Tapers seated wet had higher pull-off strengths (2,200 ± 300 N) than those seated dry (1,800 ± 200 N, p mechanics (load-displacement plots) varied due to sample type and due to wetness with differences in seating energy, seating stiffness, and seating displacement. These results show the detailed mechanics of seating during assembly and provide significant insight into the complex interplay of factors associated with even "ideal" seating (axial, quasistatic) loading. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1164-1172, 2018. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

A peer-to-peer traffic safety campaign program.

Science.gov (United States)

2014-06-01

The purpose of this project was to implement a peer-to-peer drivers safety program designed for high school students. : This project builds upon an effective peer-to-peer outreach effort in Texas entitled Teens in the Driver Seat (TDS), the : nati...

Disturbance observer based Takagi-Sugeno fuzzy control for an active seat suspension

Science.gov (United States)

Ning, Donghong; Sun, Shuaishuai; Zhang, Fei; Du, Haiping; Li, Weihua; Zhang, Bangji

2017-09-01

In this paper, a disturbance observer based Takagi-Sugeno (TS) fuzzy controller is proposed for an active seat suspension; both simulations and experiments have been performed verifying the performance enhancement and stability of the proposed controller. The controller incorporates closed-loop feedback control using the measured acceleration of the seat and deflection of the suspension; these two variables can be easily measured in practical applications, thus allowing the proposed controller to be robust and adaptable. A disturbance observer that can estimate the disturbance caused by friction, model simplification, and controller output error has also been used to compensate a H∞ state feedback controller. The TS fuzzy control method is applied to enhance the controller's performance by considering the variation of driver's weight during operation. The vibration of a heavy duty vehicle seat is largest in the frequency range between 2 Hz and 4 Hz, in the vertical direction; therefore, it is reasonable to focus on controlling low frequency vibration amplitudes and maintain the seat suspensions passivity at high frequency. Moreover, both the simulation and experimental results show that the active seat suspension with the proposed controller can effectively isolate unwanted vibration amplitudes below 4.5 Hz, when compared with a well-tuned passive seat suspension. The active controller has been further validated under bump and random road tests with both a 55 kg and a 70 kg loads. The bump road test demonstrated the controller has good transient response capabilities. The random road test result has been presented both in the time domain and the frequency domain. When with the above two loads, the controlled seat suspensions root-mean-square (RMS) accelerations were reduced by 45.5% and 49.5%, respectively, compared with a well-tuned passive seat suspension. The proposed active seat suspension controller has great potential and is very practical for application

Adaptive magnetorheological seat suspension for shock mitigation

Science.gov (United States)

Singh, Harinder Jit

This research focuses on theoretical and experimental analysis of an adaptive seat suspension employing magnetorheological energy absorber with the objective of minimizing injury potential to seated occupant of different weights subjected to broader crash intensities. The research was segmented into three tasks: (1) development of magnetorheological energy absorber, (2) biodynamic modeling of a seated occupant, and (3) control schemes for shock mitigation. A linear stroking semi-active magnetorheological energy absorber (MREA) was designed, fabricated and tested for intense impact conditions with piston velocities up to 8 m/s. MREA design was optimized on the basis of Bingham-plastic model (BPM model) in order to maximize the energy absorption capabilities at high impact velocities. Computational fluid dynamics and magnetic FE analysis were conducted to validate MREA performance. Subsequently, low-speed cyclic testing (0-2 Hz subjected to 0-5.5 A) and high-speed drop testing (0-4.5 m/s at 0 A) were conducted for quantitative comparison with the numerical simulations. Later, a nonlinear four degrees-of-freedom biodynamic model representing a seated 50th percentile male occupant was developed on the basis of experiments conducted on Hybrid II 50th percentile male anthropomorphic test device. The response of proposed biodynamic model was compared quantitatively against two different biodynamic models from the literature that are heavily implemented for obtaining biodynamic response under impact conditions. The proposed biodynamic model accurately predicts peak magnitude, overall shape and the duration of the biodynamic transient response, with minimal phase shift. The biodynamic model was further validated against 16 impact tests conducted on horizontal accelerator facility at NAVAIR for two different shock intensities. Compliance effects of human body were also investigated on the performance of adaptive seat suspension by comparing the proposed biodynamic model

Plant trial of an under-belt capacitance and gamma-ray backscatter gauge for on-belt determination of moisture in coal

International Nuclear Information System (INIS)

Cutmore, N.G.; Rafter, P.T.; Abernethy, D.A.; Millen, M.J.

1989-01-01

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance, determined using an under-belt capacitance sensor in which a fringing electric field interrogates a layer of coal on the conveyor belt directly about the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal. A plant trial of the technique was conducted at Stockton Borehole Colliery, NSW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7-14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the on-belt gauge. 6 refs., 6 figs., 3 tabs

A designated centre for people with disabilities operated by Ard Aoibhinn Services , Wexford

LENUS (Irish Health Repository)

McGrath, N

2010-07-01

The use of adult seat belts without booster seats in young children may lead to severe abdominal, lumbar or cervical spine and head and neck injuries. We describe four characteristic cases of lap belt injuries presenting to a tertiary children\\'s hospital over the past year in addition to a review of the current literature. These four cases of spinal cord injury, resulting in significant long-term morbidity in the two survivors and death in one child, arose as a result of lap belt injury. These complex injuries are caused by rapid deceleration characteristic of high impact crashes, resulting in sudden flexion of the upper body around the fixed lap belt, and consequent compression of the abdominal viscera between the lap belt and spine. This report highlights the dangers of using lap belts only without shoulder straps. Age-appropriate child restraint in cars will prevent these injuries.

A study on mechanism of wear on body seat in nozzle of diesel fuel injector

Energy Technology Data Exchange (ETDEWEB)

Jeonggee, Son; Yamashita, Toru; Sato, Susumu; Kosaka, Hidenori; Masuko, Masabumi [Tokyo Institute of Technology (Japan)

2013-06-01

Wear of nozzle's body seat of diesel fuel injector, which is caused by the collision of needle on the body seat in a nozzle, affects fuel spray behaviors and injection characteristics. Recently, to reduce the wear of body seat, DLC nozzles are widely used. The DLC on the needle which is called diamond-like carbon has a certain effect in reducing wear of body seat. However, disallowable wear is reported at limited engine operating conditions. Moreover, the wear mechanism of body seat with DLC coated needle has not been made clear yet. In this study, the influence of temperature of the body seat and fuel property on the wear of DLC nozzle was investigated with a newly developed wear testing device which was constructed based on common-rail injection system. Worn surfaces of body seat were observed by FE-SEM, laser scanning microscope and EPMA. The obtained results from the measurements show that DLC nozzle has much less wear amount than non-DLC nozzle on the body seat and the corrosive wear effect is suppressed with DLC nozzle. (orig.)

Awareness and practice of road safety measures among undergraduate medical students in a South Indian state.

Science.gov (United States)

Kulkarni, Vaman; Kanchan, Tanuj; Palanivel, C; Papanna, M K; Kumar, Nithin; Unnikrishnan, B

2013-05-01

The UN general assembly has declared 2011-2020 as the "Decade of Action for Road Safety". The declaration holds significance because road traffic accidents (RTAs) have become a major cause of morbidity and mortality, especially among the adults and middle aged individuals who constitute economically most productive age groups of society. The importance of knowledge and practice of road safety measures needs to be emphasized in the prevention of RTAs. The present study is aimed to assess the knowledge and practice of road safety measures among the students of a medical college in coastal, South India. A total of 260 medical students were included in this cross-sectional study. A semi-structured questionnaire was used to collect the relevant information from the participants. The data collected was analyzed using SPSS version 11.5. Out of the 260 participants, 149 (57.3%) were females and 111 (42.7%) were males. The overall awareness on road safety measures was slightly higher among females (20.6%) than males (19.9%). The participants had significantly low awareness with regard to alcohol and driving (4.2%), use of seat belts (20%) and use of mobile phones without hands free device (6.1%). The participants had a better knowledge about traffic signs and more than half of them identified all the signs correctly. With regard to the road safety practices, 25% were involved in drunken driving in the past one year. The practice of using mobile phones with hands free devices while driving was admitted by 20% of them. Nearly two-third participants (68%) admitted to have crossed speed limits on multiple occasions. Observations of the study emphasize on the need to generate awareness among medical students through training and IEC activities to curb the epidemic of RTAs. Copyright © 2012 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

Development of a multi-body nonlinear model for a seat-occupant system

Science.gov (United States)

Azizi, Yousof

A car seat is an important component of today's cars, which directly affects ride comfort experienced by occupants. Currently, the process of ride comfort evaluation is subjective. Alternatively, the ride comfort can be evaluated by a series of objective metrics in the dynamic response of the occupant. From previous studies it is well known that the dynamic behavior of a seat-occupant system is greatly affected by soft nonlinear viscoelastic materials used in the seat cushion. Therefore, in this research, especial attention was given to efficiently modeling the behavior of seat cushion. In the first part of this research, a phenomenological nonlinear viscoelastic foam model was proposed and its ability to capture uniaxial behavior of foam was investigated. The model is based on the assumption that the total stress can be decomposed into the sum of a nonlinear elastic component, modeled by a higher order polynomial of strain, and a nonlinear hereditary type viscoelastic component. System identification procedures were developed to estimate the model parameters using uniaxial cyclic compression data from experiments conducted at different rates on two types of low density polyurethane foams and three types of high density CONFOR foams. The performance of the proposed model was compared to that of other traditional continuum models. For each foam type, it was observed that lower order models are sufficient to describe the uniaxial behavior of the foam compressed at different rates. Although, the estimated model parameters were functions of the input strain rate. Alternatively, higher order comprehensive models, with strain independent parameters, were estimated as well. The estimated comprehensive model predicts foam responses under different compression rates. Also, a methodology was proposed to predict the stress-response of a layered foam system using the estimated models of each foam in the layers. Next, the estimated foam model was incorporated into a single

La nuova sfida di SEAT Pagine Gialle

Directory of Open Access Journals (Sweden)

Leonardo Landini

2008-03-01

Full Text Available SEAT Pagine Gialle’s new challengeSEAT Pagine Gialle is a company that for over 80 years has provided information services, search and communication tools.The companies success and notoriety is built on a customer base of about 20 million families and 3 million professional operators with a continually updated technology with which it integrates with detailed geographical information that allows it to reach millions of users every day. The services the company offers include an advanced cartographic web-based search, satellite and aerial photos, the calculation of driving instructions, weather forecasts and traffic information, 360 degree views and the modelling of whole cities in 3D.

Application of Failure Mode Effect and Criticality Analysis (FMECA to a Computer Integrated Manufacturing (CIM Conveyor Belt

Directory of Open Access Journals (Sweden)

I. Elbadawi

2018-06-01

Full Text Available Fault finding and failure predicting techniques in manufacturing and production systems often involve forecasting failures, their effects, and occurrences. The majority of these techniques predict failures that may appear during the regular system production time. However, they do not estimate the failure modes and they require extensive source code instrumentation. In this study, we suggest an approach for predicting failure occurrences and modes during system production time intervals at the University of Hail (UoH. The aim of this project is to implement failure mode effect and criticality analysis (FMECA on computer integrated manufacturing (CIM conveyors to determine the effect of various failures on the CIM conveyor belt by ranking and prioritizing each failure according to its risk priority number (RPN. We incorporated the results of FMECA in the development of formal specifications of fail-safe CIM conveyor belt systems. The results show that the highest RPN values are for motor over current failure (450, conveyor chase of vibration (400, belt run off at the head pulley (200, accumulated dirt (180, and Bowed belt (150. The study concludes that performing FMECA is highly effective in improving CIM conveyor belt reliability and safety in the mechanical engineering workshop at UoH.

Chaos on the conveyor belt.

Science.gov (United States)

Sándor, Bulcsú; Járai-Szabó, Ferenc; Tél, Tamás; Néda, Zoltán

2013-04-01

The dynamics of a spring-block train placed on a moving conveyor belt is investigated both by simple experiments and computer simulations. The first block is connected by a spring to an external static point and, due to the dragging effect of the belt, the blocks undergo complex stick-slip dynamics. A qualitative agreement with the experimental results can be achieved only by taking into account the spatial inhomogeneity of the friction force on the belt's surface, modeled as noise. As a function of the velocity of the conveyor belt and the noise strength, the system exhibits complex, self-organized critical, sometimes chaotic, dynamics and phase transition-like behavior. Noise-induced chaos and intermittency is also observed. Simulations suggest that the maximum complexity of the dynamical states is achieved for a relatively small number of blocks (around five).

Designing Train Passenger Seat by Kansei Engineering in Indonesia

Directory of Open Access Journals (Sweden)

Hapsari Sakya Nabila

2017-01-01

Full Text Available Public transport adoption is still major problem in Indonesia. Integrating impression and emotion to service may change the image of public transport, leading to fast adoption rate. As product development technique, Kansei Engineering is well known to facilitate that integration. This paper communicates the implementation of Kansei Engineering (KE in designing train passenger seat in Indonesia. The train between Bandung-Solo (8 hours journey was chosen to be the investigated object. The train was selected to be refurbished by introducing a new passenger seat design, emphasizing on the improvement of passenger experience. As the first step of KE type I technique, travel experience of the existing passengers were taken into the consideration for selecting Kansei words. It was found that the relevant Kansei words to design passenger train seat in Indonesia were: comfort, people-friendly, multifunction, safe, soft, spacious, relaxing, superior, maintainable, strong, producible, minimalist, attractive, modern, unique, and durable. Upon understanding the semantic meaning of those words, physical properties and technical specification were produced by consulting to the related members. Finally, a passenger seat with synthetic leather cover, modular design, foldable table, individual power point, bluesilver color, and adjusted to Indonesian’s anthropometry data was proposed as the final design

Optimum design of automobile seat using statistical design support system; Tokeiteki sekkei shien system no jidoshayo seat eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Kashiwamura, T [NHK Spring Co. Ltd., Yokohama (Japan); Shiratori, M; Yu, Q; Koda, I [Yokohama National University, Yokohama (Japan)

1997-10-01

The authors proposed a new practical optimum design method called statistical design support system, which consists of five steps: the effectivity analysis, reanalysis, evaluation of dispersion, the optimiza4ion and evaluation of structural reliability. In this study, the authors applied the present system to analyze and optimum design of an automobile seat frame subjected to crushing. This study should that the present method could be applied to the complex nonlinear problems such as large deformation, material nonlinearity as well as impact problem. It was shown that the optimum design of the seat frame has been solved easily using the present system. 6 refs., 5 figs., 5 tabs.

Efficacy and tolerability of micafungin monotherapy for candidemia and deep-seated candidiasis in adults with cancer.

Science.gov (United States)

Farmakiotis, Dimitrios; Tarrand, Jeffrey J; Kontoyiannis, Dimitrios P

2014-06-01

The response rate among 58 patients with cancer and candidemia or deep-seated candidiasis treated with micafungin monotherapy was 81%. Intensive care unit (ICU) stay, concomitant nonfungal infections, and acute kidney injury were significantly associated with the 30-day crude mortality rate. Severe neutropenia was an independent predictor of micafungin failure. The efficacy and safety of micafungin in cancer patients with invasive candidiasis were comparable to those reported for patients without malignancy and for cancer patients treated with caspofungin. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

Child car seats – a habitat for house dust mites and reservoir for harmful allergens

Directory of Open Access Journals (Sweden)

David Clarke

2015-02-01

Full Text Available [b]Introduction and objective[/b]. House dust mites produce allergens which can cause or aggravate diseases such as asthma, eczema and rhinitis. The objectives of this study are to quantify typical house dust mite and Der p 1 allergen levels in child car seats, and to determine external variables that may influence mite populations in cars. [b]Materials and Methods[/b]. Dust samples were collected from the child car seats and driver seats of 106 cars using a portable vacuum sampling pump over a two minute sampling period. Mites were counted and identified and results were expressed as mites per gram (mites/g of dust, while Der p 1 content of samples were measured by enzyme-linked immunosorbent assay (ELISA. Questionnaires were completed by participants to identify environmental and behavioural effects on mite populations. Results were analysed using General Linear Model (GLM procedures. [b]Results[/b]. Twelve species of mites, of which nine are known to produce harmful allergens, were recorded from 212 dust samples. Over 80% of drivers’ seats and over 77% of child car seats harboured dust mites with a significant correlation (p = 0.001 between the mites/g of dust and Der p 1 content recovered from each seat. A mean of 53 mites/g of dust per seat was recovered, with a mean Der p 1 level of 1.1µg/g. Over 12% of driver seats and 15% of child car seats contained house dust mite levels sufficient to be risk factors for sensitisation and allergic reactions. [b]Conclusions[/b]. Child car seats and driver seats are habitats to a range of mite species which can be present in sufficient concentrations to cause or aggravate allergen related illnesses in individuals who are genetically predisposed.

Flow Characteristics and Sizing of Annular Seat Valves for Digital Displacement Machines

Directory of Open Access Journals (Sweden)

Christian Nørgård

2018-01-01

Full Text Available This paper investigates the steady-state flow characteristics and power losses of annular seat valves for digital displacement machines. Annular seat valves are promising candidates for active check-valves used in digital displacement fluid power machinery which excels in efficiency in a broad operating range. To achieve high machine efficiency, the valve flow losses and the required electrical power needed for valve switching should be low. The annular valve plunger geometry, of a valve prototype developed for digital displacement machines, is parametrized by three parameters: stroke length, seat radius and seat width. The steady-state flow characteristics are analyzed using static axi-symmetric computational fluid dynamics. The pressure drops and flow forces are mapped in the valve design space for several different flow rates. The simulated results are compared against measurements using a valve prototype. Using the simulated maps to estimate the flow power losses and a simple generic model to estimate the electric power losses, both during digital displacement operation, optimal designs of annular seat valves, with respect to valve power losses, are derived under several different operating conditions.

Drinking and Driving – What You Need to Know

Centers for Disease Control (CDC) Podcasts

This podcast is based on the October, 2011 CDC Vital Signs report. Drinking and driving is still a serious problem. Crashes involving alcohol-impaired drivers kill nearly 11,000 people each year. If you’re drinking, designate a non-drinking driver before you start, call a cab, or get a ride home. Also, always wear your seat belt. Seat belts reduce the risk of serious injuries and death in a crash by 50 percent.

Drinking and Driving – What You Need to Know PSA (:60)

Centers for Disease Control (CDC) Podcasts

This 60 second PSA is based on the October, 2011 CDC Vital Signs report. Drinking and driving is still a serious problem. Crashes involving alcohol-impaired drivers kill nearly 11,000 people each year. If you’re drinking, designate a non-drinking driver before you start, call a cab, or get a ride home. Also, always wear your seat belt. Seat belts reduce the risk of serious injuries and death in a crash by 50 percent.

30 CFR 75.1403-5 - Criteria-Belt conveyors.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Criteria-Belt conveyors. 75.1403-5 Section 75... Criteria—Belt conveyors. (a) Positive-acting stop controls should be installed along all belt conveyors... can be stopped or started at any location. (b) Belt conveyors used for regularly scheduled mantrips...

Design and evaluation of a suspension seat to reduce vibration exposure of subway operators: a case study.

Science.gov (United States)

Marcotte, Pierre; Beaugrand, Sylvie; Boutin, Jérôme; Larue, Christian

2010-01-01

Subway operators have complained about discomfort caused by whole-body vibration. To address this problem, a suspension seat with extensive ergonomic features has been adapted to the confined space of the subway operator cab. The suspension was modified from an existing suspension in order to reduce the dominant frequency of the subway vertical vibration (2.4 Hz). The suspension seat has been extensively tested on a vertical hydraulic shaker. These tests have shown that the SEAT value was lower for a higher vibration level, for higher subject weight, and for the suspension adjusted at median height. The seat also produces a lower SEAT value when there was a predominance of the 6 Hz vibration component. The horizontal seat adjustments had no influence on the suspension SEAT value. Removing the suspension damper also decreases the SEAT value for all the tested configurations. The final version of the suspension seat prototype was validated during normal subway operation with 19 different operators having weight in the 5th, 50th and 95th percentile of the operator population. Accelerations were measured with triaxial accelerometers at the seat cushion, above the suspension and on the floor. In addition to the vibration measurements, each operator was asked about his perceived discomfort from vibration exposure. Globally, the suspension seat attenuated the vertical vibration (SEAT values from 0.86 to 0.99), but discomfort due to amplification of the 2.4 Hz component occurred when the suspension height was adjusted at the minimum, even when the global weighted acceleration was lower (SEAT value < 1). These results suggest that in order to reduce the discomfort caused by whole-body vibration, the transmissibility of the seat should also be considered, in particular when there is a dominant frequency in the vibration spectra.

Comparison of car seats in low speed rear-end impacts using the BioRID dummy and the new neck injury criterion (NIC).

Science.gov (United States)

Boström, O; Fredriksson, R; Håland, Y; Jakobsson, L; Krafft, M; Lövsund, P; Muser, M H; Svensson, M Y

2000-03-01

Long-term whiplash associated disorders (WAD) 1-3 sustained in low velocity rear-end impacts is the most common disability injury in Sweden. Therefore, to determine neck injury mechanisms and develop methods to measure neck-injury related parameters are of importance for current crash-safety research. A new neck injury criterion (NIC) has previously been proposed and evaluated by means of dummy, human and mathematical rear-impact simulations. So far, the criterion appears to be sensitive to the major car and collision related risk factors for injuries with long-term consequences. To further evaluate the applicability of NIC, four seats were tested according to a recently proposed sled-test procedure. 'Good' as well as 'bad' seats were chosen on the basis of a recently presented disability risk ranking list. The dummy used in the current tests was the Biofidelic Rear Impact Dummy (BioRID). The results of this study showed that NICmax values were generally related to the real-world risk of long-term WAD 1-3. Furthermore, these results suggested that NICmax calculated from sled tests using the BioRID dummy can be used for evaluating the neck injury risk of different car seats.

Synchronous and Cogged Fan Belt Performance Assessment

Energy Technology Data Exchange (ETDEWEB)

Cutler, Dylan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Dean, Jesse [National Renewable Energy Lab. (NREL), Golden, CO (United States); Acosta, Jason [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-02-01

The GSA Regional GPG Team commissioned the National Renewable Energy Laboratory (NREL) to perform monitoring of cogged V-belts and synchronous belts on both a constant volume and a variable air volume fan at the Byron G. Rodgers Federal Building and U.S. Courthouse in Denver, Colorado. These motor/fan combinations were tested with their original, standard V-belts (appropriately tensioned by an operation and maintenance professional) to obtain a baseline for standard operation. They were then switched to the cogged V-belts, and finally to synchronous belts. The power consumption by the motor was normalized for both fan speed and air density changes. This was necessary to ensure that the power readings were not influenced by a change in rotational fan speed or by the power required to push denser air. Finally, energy savings and operation and maintenance savings were compiled into an economic life-cycle cost analysis of the different belt options.

Association Between NCAP Ratings and Real-World Rear Seat Occupant Risk of Injury.

Science.gov (United States)

Metzger, Kristina B; Gruschow, Siobhan; Durbin, Dennis R; Curry, Allison E

2015-01-01

Several studies have evaluated the correlation between U.S. or Euro New Car Assessment Program (NCAP) ratings and injury risk to front seat occupants, in particular driver injuries. Conversely, little is known about whether NCAP 5-star ratings predict real-world risk of injury to restrained rear seat occupants. The NHTSA has identified rear seat occupant protection as a specific area under consideration for improvements to its NCAP. In order to inform NHTSA's efforts, we examined how NCAP's current 5-star rating system predicts risk of moderate or greater injury among restrained rear seat occupants in real-world crashes. We identified crash-involved vehicles, model year 2004-2013, in NASS-CDS (2003-2012) with known make and model and nonmissing occupant information. We manually matched these vehicles to their NCAP star ratings using data on make, model, model year, body type, and other identifying information. The resultant linked NASS-CDS and NCAP database was analyzed to examine associations between vehicle ratings and rear seat occupant injury risk; risk to front seat occupants was also estimated for comparison. Data were limited to restrained occupants and occupant injuries were defined as any injury with a maximum Abbreviated Injury Scale (AIS) score of 2 or greater. We linked 95% of vehicles in NASS-CDS to a specific vehicle in NCAP. The 18,218 vehicles represented an estimated 6 million vehicles with over 9 million occupants. Rear seat passengers accounted for 12.4% of restrained occupants. The risk of injury in all crashes for restrained rear seat occupants was lower in vehicles with a 5-star driver rating in frontal impact tests (1.4%) than with 4 or fewer stars (2.6%, P =.015); results were similar for the frontal impact passenger rating (1.3% vs. 2.4%, P =.024). Conversely, side impact driver and passenger crash tests were not associated with rear seat occupant injury risk (driver test: 1.7% for 5-star vs. 1.8% for 1-4 stars; passenger test: 1.6% for 5

Feed chute geometry for minimum belt wear

Energy Technology Data Exchange (ETDEWEB)

Roberts, A W; Wiche, S J [University of Newcastle, Newcastle, NSW (Australia). Centre for Bulk Solids and Particulate Technologies

1998-09-01

The paper is concerned with the feeding and transfer of bulk solids in conveyor belt operation. The paper focuses on chute design where the objective is to prevent spillage and minimise both chute and belt wear. It is shown that these objectives may be met through correct dynamic design of the chute and by directing the flow of bulk solids onto the belt at an acceptable incidence angle. The aim is to match the tangential velocity component of the feed velocity as close as possible to the belt velocity. At the same time, it is necessary to limit the impact pressure due to the change in momentum of the bulk solid as it feeds onto the belt. 2 refs., 8 figs.

Determination of relative immobile and sliding areas between carrying and tractive belts in using of belt conveyor intermediate drives

OpenAIRE

Goncharov K.A.

2015-01-01

Method of determination of relative immobile and sliding areas between carrying and tractive belts in places of mount-ing of belt conveyor intermediate drives made in the form of tractive contours is proposed. The example shows potential of this method in multidrive belt conveyor design process.

An image-based method to measure all-terrain vehicle dimensions for engineering safety purposes.

Science.gov (United States)

Jennissen, Charles A; Miller, Nathan S; Tang, Kaiyang; Denning, Gerene M

2014-04-01

All-terrain vehicle (ATV) crashes are a serious public health and safety concern. Engineering approaches that address ATV injury prevention are critically needed. Avenues to pursue include evidence-based seat design that decreases risky behaviours, such as carrying passengers and operation of adult-size vehicles by children. The goal of this study was to create and validate an image-based method to measure ATV seat length and placement. Publicly available ATV images were downloaded. Adobe Photoshop was then used to generate a vertical grid through the centre of the vehicle, to define the grid scale using the manufacturer's reported wheelbase, and to determine seat length and placement relative to the front and rear axles using this scale. Images that yielded a difference greater than 5% between the calculated and the manufacturer's reported ATV lengths were excluded from further analysis. For the 77 images that met inclusion criteria, the mean±SD for the difference in calculated versus reported vehicle length was 1.8%±1.2%. The Pearson correlation coefficient for comparing image-based seat lengths determined by two independent measurers (20 models) and image-based lengths versus lengths measured at dealerships (12 models) were 0.95 and 0.96, respectively. The image-based method provides accurate and reproducible results for determining ATV measurements, including seat length and placement. This method greatly expands the number of ATV models that can be studied, and may be generalisable to other motor vehicle types. These measurements can be used to guide engineering approaches that improve ATV safety design.

30 CFR 75.1108 - Approved conveyor belts.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Approved conveyor belts. 75.1108 Section 75... Fire-Resistant Hydraulic Fluids on Underground Equipment § 75.1108 Approved conveyor belts. (a) Until December 31, 2009 conveyor belts placed in service in underground coal mines shall be: (1) Approved under...

Determination of relative immobile and sliding areas between carrying and tractive belts in using of belt conveyor intermediate drives

Directory of Open Access Journals (Sweden)

Goncharov K.A.

2015-12-01

Full Text Available Method of determination of relative immobile and sliding areas between carrying and tractive belts in places of mount-ing of belt conveyor intermediate drives made in the form of tractive contours is proposed. The example shows potential of this method in multidrive belt conveyor design process.

Whole-body Vibration Exposure Intervention among Professional Bus and Truck Drivers: A Laboratory Evaluation of Seat-suspension Designs.

Science.gov (United States)

Blood, Ryan P; Yost, Michael G; Camp, Janice E; Ching, Randal P

2015-01-01

Long-term exposure to seated whole-body vibration (WBV) is one of the leading risk factors for the development of low back disorders. Professional bus and truck drivers are regularly exposed to continuous WBV, since they spend the majority of their working hours driving heavy vehicles. This study measured WBV exposures among professional bus and truck drivers and evaluated the effects of seat-suspension designs using simulated field-collected data on a vibration table. WBV exposures were measured and compared across three different seat designs: an air-ride bus seat, an air-ride truck seat, and an electromagnetically active (EM-active) seat. Air-ride seats use a compressed-air bladder to attenuate vibrations, and they have been in operation throughout the transportation industry for many years. The EM-active seat is a relatively new design that incorporates a microprocessor-controlled actuator to dampen vibration. The vibration table simulated seven WBV exposure scenarios: four segments of vertical vibration and three scenarios that used field-collected driving data on different road surfaces-a city street, a freeway, and a section of rough roadway. The field scenarios used tri-axial WBV data that had been collected at the seat pan and at the driver's sternum, in accordance with ISO 2631-1 and 2631-5. This study found that WBV was significantly greater in the vertical direction (z-axis) than in the lateral directions (x-and y-axes) for each of the three road types and each of the three types of seats. Quantitative comparisons of the results showed that the floor-to-seat-pan transmissibility was significantly lower for the EM-active seat than for either the air-ride bus seat or the air-ride truck seat, across all three road types. This study also demonstrated that seat-suspension designs have a significant effect on the vibrations transmitted to vehicle operators, and the study's results may prove useful in designing future seat suspensions.

Crustal Deformation around Zhangjiakou-Bohai Seismically Active Belt

Science.gov (United States)

Jin, H.; Fu, G.; Kato, T.

2011-12-01

Zhangjiakou-Bohai belt is a seismically active belt located in Northern China around Beijing, the capital of China. Near such a belt many great earthquakes occurred in the past centuries (e.g. the 1976 Tanshan Ms7.8 earthquake, the 1998 Zhangbei Ms6.2 earthquake, etc). Chinese Government established dense permanent and regional Global Positioning System (GPS) stations in and near the area. We collected and analyzed all the GPS observation data between 1999 and 2009 around Zhangjiakou-Bohai seismic belt, and obtained velocities at 143 stations. At the same time we investigated Zhangjiakou-Bohai belt slip rate for three profiles from northwest to southeast, and constructed a regional strain field on the Zhangjiakou-Bohai seismic belt region by least-square collocation. Based on the study we found that: 1) Nowadays the Zhangjiakou-Bohai seismic belt is creeping with left-lateral slip rate of 2.0mm~2.4mm/a, with coupling depth of 35~50km; 2) In total, the slip and coupling depth of the northwestern seismic belt is less than the one of southeast side; 3) The maximum shear strain is about 3×10-8 at Beijing-Tianjin-Tangshan area.

Root cause analysis of SI line-seated thermal sleeve separation failures

International Nuclear Information System (INIS)

Jo, Jong Chull; Jhung, Myung Jo; Kim, Hho Jung

2004-01-01

At conventional pressurized water reactors, a thermal sleeve (named simply 'sleeve' hereafter) is seated inside the nozzle part of each Safety Injection (SI) branch pipe to prevent and relieve potential excessive transient thermal stress in the nozzle wall when a cold water is injected during the safety injection mode Recently, mechanical failures that the sleeves are separated from the SI branch pipe and fall into the connected cold leg main pipe were occurred in sequence at Yonggwang units 5 and 6 and Ulchin unit 5. There were many activities and efforts to figure out the causes of those failures with experts' reasoning, but the proposed causes were derived from superficial views rather than physically concrete grounds or analysis results. The prerequisites to find out the root causes of failure mechanism will be to identify the flow situation in the pipe junction area connecting the cold leg with the SI pipe and to know the vibration characteristics of sleeves. This paper investigates the flow field in the pipe junction thru a numerical simulation and vibration characteristics of thermal sleeves thru a modal analysis, from which the root causes of sleeve separation mechanism are analyzed

Legislating child restraint usage -Its effect on self-reported child restraint use rates in a central city.

Science.gov (United States)

Brixey, Suzanne; Ravindran, Karthik; Guse, Clare E

2010-02-01

To assess the effect of the newly enacted child passenger safety law, Wisconsin Act 106, on self-report of proper restraint usage of children in Milwaukee's central city population. A prospective, non-randomized study design was used. The settings used were (a) a pediatric urban health center, and (b) two Women, Infants and Children offices in Milwaukee, Wisconsin. Participants included 11,566 surveys collected over 18 months that spanned the pre-legislation and post-legislation time periods from February 2006 through August 2008. The study set out to assess appropriate child passenger restraint. The results showed that the changes in adjusted proper restraint usage rates for infants between the pre-law, grace period, and post-fine periods were 94%, 94%, and 94% respectively. For children 1-3years old, the adjusted proper usage rates were 65%, 63%, and 59%, respectively. And for children 4-7years old, the rates were 43%, 44% and 42%, respectively. There was a significant increase in premature booster seat use in children who should have been restrained in a rear- or forward-facing car seat (10% pre-law, 12% grace period, 20% post-fine; padvertising and marketing to the correct age group, ease of installation, and mechanisms to prevent incorrect safety strap and harness placement. To ensure accurate and consistent use on every trip, car seat manufacturers must ensure that best practice recommendations for use as well as age, weight, and height be clearly specified on each child restraint. The authors support the United States Department of Transportation's new consumer program that will assist caregivers in identifying the child seat that will fit in their vehicle. In addition, due to the increase in premature graduation of children into belt-positioning booster seats noted as a result of legislation, promoting and marketing booster seat use for children less than 40 pounds should not be accepted. Child passenger safety technicians must continue to promote best

Affirmative Action: Reservation Seats untuk Perempuan di Parlemen India

Directory of Open Access Journals (Sweden)

Evi Yunita Kurniaty

2015-12-01

Full Text Available The study aims to help us understand and analyze women's efforts in the policy-making process to increase their political participation in the constitutional and electoral processes. We can also see the extent to which the values rooted in the patriarchal culture in a society and what can be done and reduce them. Affirmative action is carried out in India by applying the system of reservation seats for women in the Indian Parliament. This is done in India is proven to increase the number of women in the Indian Parliament. By the way there are quotas for women as a strategy for accessing the political arena has growing support among MPs. In this study, Indonesia could get a reservation seats of learning about the system is done. To increase the representation in the "area" is very difficult to be touched by a quota system which is run now, it can be done with reservation seats quota to ensure women's representation in parliament.

Method of monitoring, inspecting or testing conveyor belts

International Nuclear Information System (INIS)

Van der Walt, A.J.

1985-01-01

An invention is discussed which provides a method, installation and kit for monitoring, inspecting or testing a conveyor belt. Provision is made to transmit penetrating rays such as X-rays through a moving conveyor belt, forming a visible moving image from rays transmitted through the belt, and visually inspecting such moving image, after recording it if desired, to ascertain the condition of the interior of the belt. Typically an X-ray tube head is used to transmit the rays through the belt to a fluorescent screen which forms the image. The moving image can be recorded by means of a video camera

The development of an electronic system to continually monitor, indicate and control, 'belt slippage' in industrial friction 'V' belt drive transmission systems

International Nuclear Information System (INIS)

Brown, R E

2012-01-01

Belts have been used for centuries as a mechanism to transfer power from some form of drive system to a variety of load systems. Within industry today, many designs of belts but particularly friction, trapezoidal shaped 'V' belts are used and generally transfer power generated by electrical motors to numerous forms of driven load systems. It is suggested that belt systems, through their simplicity are sadly neglected by maintenance functions and generally are left unattended until high degrees of 'belt slippage' through loss of friction or 'belt breakage' provokes maintenance attention. These circumstances are most often identified through the reduced or loss of manufacturing production or the occurrence of catastrophic circumstances such as fire caused through excessive friction/ high belt slippage conditions. Obviously, these situations incur financial losses to companies and in some cases the near loss of the company's main manufacturing plant. Consequently, a satisfactory, viable solution is currently sought by industry to improve on current labour intensive maintenance practices. This paper will present an account of the development of an industrially robust, accurate and repeatable electronic system which continually monitors and indicates the degree of 'slippage' in a 'V' belt drive transmission system and in the circumstance of belt breakage or high belt slippage will enable and control the switching off the drive motor.

Ergonomic Analysis of Tricycle Sidecar Seats: Basis for Proposed Standard Design

Directory of Open Access Journals (Sweden)

Michael C. Godoy

2015-12-01

Full Text Available Ergonomics (also called human factors engineering is the study of human characteristics for the appropriate design of the living and work environment. It is applied in various industrial areas which includes transportation.Tricycle being one of the most common means of public transportation in Lipa City has various adaptations to suit the culture, and environment. The purpose of this study is to analyze the variability in design of the tricycles in Lipa City, Philippines and propose a standard ergonomically designed tricycle sidecar seat for a greater population. The study was conducted at 26 tricycle terminals with 232 tricycle samples within Lipa City proper including the public market area where 400 commuters were given questionnaires to determine the risk factors associated with the existing tricycle sidecar seat design. Anthropometric measurements of 100 males and 100 female commuters were obtained together with the sidecar dimensions of 232 tricycles to substantiate the observed variations in design. Using the design for the average and design for the extremes, it was found out that most of the tricycles in Lipa City, Philippines have inappropriate inclined seat and lowered sidecar seat pan height which can result to leg and abdominal pain; narrowed seat pan depth which caused pressure on buttocks and legs; narrowed backrest width which can cause upper and low back pain; low backrest height that can pose upper back pain; which can also result to abdominal pain; inclined backrest and limited vertical clearance which can cause upper back pain and neck pain. The researcher proposed a sidecar seat design standard which can be used by the Land Transportation Office, and Land Transportation Franchising and Regulatory Board to provide ease, comfort, and convenience to the passengers.

Grinding Glass Disks On A Belt Sander

Science.gov (United States)

Lyons, James J., III

1995-01-01

Small machine attached to table-top belt sander makes possible to use belt sander to grind glass disk quickly to specified diameter within tolerance of about plus or minus 0.002 in. Intended to be used in place of production-shop glass grinder. Held on driveshaft by vacuum, glass disk rotated while periphery ground by continuous sanding belt.

Autonomous booster device of a safety valve

International Nuclear Information System (INIS)

Namand, H.

1983-01-01

The invention concerns an autonomous booster device of a protection safety valve of a pressure vessel. The valve comprises a hollow structure, a seat connected with a mobile flap forming one piece with a stem and a calibration spring bearing on the stem and on the valve structure to maintain the flap bearing on the seat. The stem of the flap is prolongated in a box forming one piece with the valve structure and receives an added push of a spring. The box acts as a pressure device of which the piston can exercise on the stem a push opposite to and larger than the spring one. The feeding device of the pressure box is finally described in detail [fr

The efficacy and safety of inflatable obstetric belts for management of the second stage of labor.

Science.gov (United States)

Kang, Jin Hee; Lee, Gun Ho; Park, Young Bae; Jun, Hye Sun; Lee, Kyoung Jin; Hahn, Won Bo; Park, Sang Won; Park, Hee Jin; Cha, Dong Hyun

2009-10-01

This study was designed to assess the effect of inflatable obstetric belts on uterine fundal pressure in the management of the second stage of labor. One hundred twenty-three nulliparas with a singleton cephalic pregnancy at term were randomized. Standard care was performed in the control group, and uterine fundal pressure by the Labor Assister (Baidy M-420/Curexo, Inc., Seoul, Korea) was utilized in addition to standard care in the active group. The Labor Assister is an inflatable obstetric belts that synchronized to apply uniform fundal pressure during a uterine contraction. The 62 women in the active group spent less time in the second stage of labor when compared to the 61 women in the control group (41.55+/-30.39 min vs. 62.11+/-35.99 min). There was no significant difference in perinatal outcomes between the two groups. In conclusion, the uterine fundal pressure exerted by the Labor Assister reduces the duration of the second stage of labor without attendant complications.

Colors of Inner Disk Classical Kuiper Belt Objects

Science.gov (United States)

Romanishin, W.; Tegler, S. C.; Consolmagno, G. J.

2010-07-01

We present new optical broadband colors, obtained with the Keck 1 and Vatican Advanced Technology telescopes, for six objects in the inner classical Kuiper Belt. Objects in the inner classical Kuiper Belt are of interest as they may represent the surviving members of the primordial Kuiper Belt that formed interior to the current position of the 3:2 resonance with Neptune, the current position of the plutinos, or, alternatively, they may be objects formed at a different heliocentric distance that were then moved to their present locations. The six new colors, combined with four previously published, show that the ten inner belt objects with known colors form a neutral clump and a reddish clump in B-R color. Nonparametric statistical tests show no significant difference between the B-R color distribution of the inner disk objects compared to the color distributions of Centaurs, plutinos, or scattered disk objects. However, the B-R color distribution of the inner classical Kuiper Belt Objects does differ significantly from the distribution of colors in the cold (low inclination) main classical Kuiper Belt. The cold main classical objects are predominately red, while the inner classical belt objects are a mixture of neutral and red. The color difference may reveal the existence of a gradient in the composition and/or surface processing history in the primordial Kuiper Belt, or indicate that the inner disk objects are not dynamically analogous to the cold main classical belt objects.

COLORS OF INNER DISK CLASSICAL KUIPER BELT OBJECTS

International Nuclear Information System (INIS)

Romanishin, W.; Tegler, S. C.; Consolmagno, G. J.

2010-01-01

We present new optical broadband colors, obtained with the Keck 1 and Vatican Advanced Technology telescopes, for six objects in the inner classical Kuiper Belt. Objects in the inner classical Kuiper Belt are of interest as they may represent the surviving members of the primordial Kuiper Belt that formed interior to the current position of the 3:2 resonance with Neptune, the current position of the plutinos, or, alternatively, they may be objects formed at a different heliocentric distance that were then moved to their present locations. The six new colors, combined with four previously published, show that the ten inner belt objects with known colors form a neutral clump and a reddish clump in B-R color. Nonparametric statistical tests show no significant difference between the B-R color distribution of the inner disk objects compared to the color distributions of Centaurs, plutinos, or scattered disk objects. However, the B-R color distribution of the inner classical Kuiper Belt Objects does differ significantly from the distribution of colors in the cold (low inclination) main classical Kuiper Belt. The cold main classical objects are predominately red, while the inner classical belt objects are a mixture of neutral and red. The color difference may reveal the existence of a gradient in the composition and/or surface processing history in the primordial Kuiper Belt, or indicate that the inner disk objects are not dynamically analogous to the cold main classical belt objects.

Speed Controlled Belt Conveyors: Drives and Mechanical Considerations