WorldWideScience

Sample records for safety quality control

  1. Quality control guarantees the safety of radiotherapy

    International Nuclear Information System (INIS)

    Aaltonen, P.

    1994-01-01

    While radiotherapy equipment has seen some decisive improvements in the last few decades, the technology has also become more complicated. The advanced equipment produces increasingly good treatment results, but the condition of the equipment must be controlled efficiently so as to eliminate any defects that might jeopardise patient safety. The quality assurance measures that are taken to show that certain equipment functions as required are known as quality control. The advanced equipment and stricter requirements set for the precision of radiotherapy have meant that more attention must be paid to quality control. The present radiation legislation stipulates that radiotherapy equipment must undergo regular quality control. The implementation of the quality control is supervised by the Finnish Centre for Radiation and Nuclear Safety (STUK). Hospitals carry out quality control in accordance with a programme approved by STUK, and STUK inspectors periodically visit hospitals to check the results of quality control. (orig.)

  2. Safety of timber : An analysis of quality control options

    NARCIS (Netherlands)

    Kovryga, A.; Stapel, P.; Van de Kuilen, J.W.G.

    2014-01-01

    The quality assurance of timber properties is important for the safety of timber structures. In the current study, the quality control options of timber are analysed under the prism of the different growth regions. Therefore, these options - machine and output control - are simulated in accordance

  3. Watershed safety and quality control by safety threshold method

    Science.gov (United States)

    Da-Wei Tsai, David; Mengjung Chou, Caroline; Ramaraj, Rameshprabu; Liu, Wen-Cheng; Honglay Chen, Paris

    2014-05-01

    Taiwan was warned as one of the most dangerous countries by IPCC and the World Bank. In such an exceptional and perilous island, we would like to launch the strategic research of land-use management on the catastrophe prevention and environmental protection. This study used the watershed management by "Safety Threshold Method" to restore and to prevent the disasters and pollution on island. For the deluge prevention, this study applied the restoration strategy to reduce total runoff which was equilibrium to 59.4% of the infiltration each year. For the sediment management, safety threshold management could reduce the sediment below the equilibrium of the natural sediment cycle. In the water quality issues, the best strategies exhibited the significant total load reductions of 10% in carbon (BOD5), 15% in nitrogen (nitrate) and 9% in phosphorus (TP). We found out the water quality could meet the BOD target by the 50% peak reduction with management. All the simulations demonstrated the safety threshold method was helpful to control the loadings within the safe range of disasters and environmental quality. Moreover, from the historical data of whole island, the past deforestation policy and the mistake economic projects were the prime culprits. Consequently, this study showed a practical method to manage both the disasters and pollution in a watershed scale by the land-use management.

  4. Quality Control Activities Related to Mechanical Maintenance of Safety Related Components at Krsko NPP

    International Nuclear Information System (INIS)

    Djakovic, D.

    2016-01-01

    For successful, safe and reliable operation of nuclear power plant, maintenance processes have to be systematically controlled and procedures for quality control of maintenance activities shall be established. This is requested by the quality assurance program, which shall provide control over activities affecting the quality of structures, systems, and components, considering their importance to safety. As a part of Quality and Nuclear Oversight Division (QNOD; SKV), the Quality Control Department (QC) provides quality control activities, which are deeply involved in maintenance processes at Krsko NPP, both on safety related and non-safety related (non-nuclear safety) components. QC activities on safety related components have to fulfil all requirements, which will enable the components to perform their intended safety functions. This paper describes quality control activities related to mechanical maintenance of safety related components at Krsko NPP and significant role of the Krsko plant QC Department in three particular maintenance cases connected with safety related components. In these three specific cases, the QC has confirmed its importance in compliance with quality assurance program and presented its significant added value in providing safe and reliable operation of the plant. The first maintenance activity was installation of nozzle check valves in the scope of a modification for improving regulation of spent fuel pit pumps. The QC Department performed receipt inspection of the valves. Using non-destructive examination methods and X-ray spectrometry, it was found out that the valve diffuser was made of improper material, which could cause progressive corrosion of the valve diffuser in borated water and consequently a loss of safety function of the valves followed by long-term consequences. The second one was the receipt inspection of containment ventilation fan coolers. The coolers were claimed and sent back to the supplier because the QC Department

  5. Specification of safety requirements for waste packages with respect to practicable quality control measures

    International Nuclear Information System (INIS)

    Gruendler, D.; Wurtinger, W.

    1987-01-01

    Waste packages for disposal in a repository in the Federal Republic of Germany have to meet safety requirements derived from site specific safety analyses. The examination of the waste packages with regard to compliance with these requirements is the main objective of quality control measures. With respect to quality control the requirements have to be specified in a way that practicable control measures can be applied. This is dealt with for the quality control of the activity inventory and the quality control of the waste form. The paper discusses the determination of the activity of hard-to-measure radionuclides and the specification of safety related requirements for the waste form and the packaging using typical examples

  6. Food Safety and Quality Control: Hints from Proteomics

    Directory of Open Access Journals (Sweden)

    Angelo D'Alessandro

    2012-01-01

    Full Text Available Over the last decade, proteomics has been successfully applied to the study of quality control in production processes of food (including meat, wine and beer, transgenic plants and milk and food safety (screening for food-derived pathogens. Indeed, food quality and safety and their influence on the health of end consumers have growingly become a founding principle in the international agenda of health organizations. The application of proteomics in food science was at first characterized by exploratory analyses of food of various origin (bovine, swine, chicken or lamb meat, but also transgenic food such as genetically modified maize, for example and beverages (beer, wine, in parallel to the genomic and transcriptomic approaches seeking determination of quantitative trait loci. In the last few years, technical improvements such as microbial biotyping strategies have growingly allowed proteomicists to address the safety issue as well. The newly introduced technical improvements (instrumentation characterized by higher sensitivity such as mass spectrometers have paved the way for the individuation of food-contaminating pathogens in a fast and efficient workflow which is mandatory in industrial food production chains.

  7. Critical review of controlled release packaging to improve food safety and quality.

    Science.gov (United States)

    Chen, Xi; Chen, Mo; Xu, Chenyi; Yam, Kit L

    2018-03-19

    Controlled release packaging (CRP) is an innovative technology that uses the package to release active compounds in a controlled manner to improve safety and quality for a wide range of food products during storage. This paper provides a critical review of the uniqueness, design considerations, and research gaps of CRP, with a focus on the kinetics and mechanism of active compounds releasing from the package. Literature data and practical examples are presented to illustrate how CRP controls what active compounds to release, when and how to release, how much and how fast to release, in order to improve food safety and quality.

  8. Safety assessment and quality control of medical x-ray facilities in some hospitals in Ghana

    International Nuclear Information System (INIS)

    Darko, E.O.; Charles, D.F.

    1998-01-01

    Safety assessment and quality control measurements of diagnostic x-ray installations were carried out in five hospitals in Ghana. The study was focused on the siting, design and construction of the buildings housing the x-ray units, assessment of safety systems and devices and measurements of the technical performance, and film processing conditions. The location, inadequacies in the design/construction, unavailability of relevant safety systems and devices, violation of basic safety principles and poor performance of some of the x-ray facilities indicate the need to improve quality control programmes, safety culture and enforcement of regulatory standards in diagnostic x-ray examinations in Ghana. (author). 8 refs., 11 tabs., 8 figs

  9. FOOD QUALITY MANAGEMENT AND SAFETY

    OpenAIRE

    Rizwana Khatoon; Debkumar Chakraborty; R.C. Chandni; Amar Sankar; A.V. Raghu

    2017-01-01

    Food safety system mainly focuses on identifying and preventing hazards that may lead product to deteriorate. The main important of manufacturing practice is a system that ensures that products meet food safety, quality and legal requirements. The hazard analysis and critical control point system, applies to food safety management, uses the approach of controlling critical points in food handling to prevent food safety problems. Besides enhancing food safety, other benefits of applying HACCP ...

  10. New Paradigm in Nuclear Safety from Quality Assurance to Safety Management System

    International Nuclear Information System (INIS)

    Lim, Nam-Jin; Park, Chan-Gook; Nam, Ji-Hee; Kim, Kwan-Hyun; Kwon, Hyuk-il; Lee, Young-Gun Lee

    2006-01-01

    The initial concept of Quality Control (QC) controlling the quality of products is now evolving toward the Management System (MS) achieving safety, through Quality Assurance (QA) ensuring the quality of products and Quality Management (QM) managing the quality by a systematic approach. Nuclear safety can be achieved through an integrated MS that ensures the health, environmental, security, quality and economic requirements being considered together with nuclear safety requirements. MS approach is developed through realizing that most of nuclear accidents had occurred not by the malfunction of hardware or equipment, but by the human error. The MS is a set of inter-related or interacting elements (system) that establishes policies and objectives and which enables those objectives to be achieved in an efficient and effective way

  11. Radiation safety and quality control in the cyclotron laboratory

    International Nuclear Information System (INIS)

    Sharma, S.; Krause, G.; Ebadi, M.

    2006-01-01

    Radiation safety was determined to maintain quality control in the cyclotron laboratory. Based on the results of 438 runs in the Faraday cup (20 μA for 10 min), 20 runs on 18 O-water target (40 μA for 2 h) and 10 runs on 18 O-gas targets (30 μA for 45 min), we have established that occupationally exposed workers remain 10 ± 5 times below federal regulatory limits (FRLs) in the cyclotron vault, 30 ± 8 times below FRL in the radiochemistry laboratory and 200 ± 10 times below the FRL outside the cyclotron laboratory during beam operation. (The FRL for unrestricted area are <20 μSv in 1 h.) The non-occupationally exposed workers serving in offices in the vicinity of the cyclotron vault within 100 m distance remained 200 times below the FRL irrespective of beam being on or off, suggesting that routine beam operation of 40 μA for 2 h once a day during office hours is safe provided quality control and system performance measures as discussed in this report are strictly maintained. (authors)

  12. [Quality control in herbal supplements].

    Science.gov (United States)

    Oelker, Luisa

    2005-01-01

    Quality and safety of food and herbal supplements are the result of a whole of different elements as good manufacturing practice and process control. The process control must be active and able to individuate and correct all possible hazards. The main and most utilized instrument is the hazard analysis critical control point (HACCP) system the correct application of which can guarantee the safety of the product. Herbal supplements need, in addition to standard quality control, a set of checks to assure the harmlessness and safety of the plants used.

  13. A holistic strategy for quality and safety control of traditional Chinese medicines by the "iVarious" standard system.

    Science.gov (United States)

    Chen, Anzhen; Sun, Lei; Yuan, Hang; Wu, Aiying; Lu, Jingguang; Ma, Shuangcheng

    2017-10-01

    An effective quality control system is the key to ensuring the quality, safety and efficacy of traditional Chinese medicines (TCMs). However, the current quality standard research lacks the top-design and systematic design, mostly based on specific technologies or evaluation methods. To resolve the challenges and questions of quality control of TCMs, a brand-new quality standard system, named "iVarious", was proposed. The system comprises eight elements in a modular format. Meaning of every element was specifically illustrated via corresponding research instances. Furthermore, frankincense study was taken as an example for demonstrating standards and research process, based on the "iVarious" system. This system highlighted a holistic strategy for effectiveness, security, integrity and systematization of quality and safety control standards of TCMs. The establishment of "iVarious" integrates multi-disciplinary technologies and progressive methods, basis elements and key points of standard construction. The system provides a novel idea and technological demonstration for regulation establishment of TCMs quality standards.

  14. Software quality assurance and software safety in the Biomed Control System

    International Nuclear Information System (INIS)

    Singh, R.P.; Chu, W.T.; Ludewigt, B.A.; Marks, K.M.; Nyman, M.A.; Renner, T.R.; Stradtner, R.

    1989-01-01

    The Biomed Control System is a hardware/software system used for the delivery, measurement and monitoring of heavy-ion beams in the patient treatment and biology experiment rooms in the Bevalac at the Lawrence Berkeley Laboratory (LBL). This paper describes some aspects of this system including historical background philosophy, configuration management, hardware features that facilitate software testing, software testing procedures, the release of new software quality assurance, safety and operator monitoring. 3 refs

  15. Patient Safety and Healthcare Quality

    Directory of Open Access Journals (Sweden)

    Aikaterini Toska

    2012-01-01

    Full Text Available Introduction: Due to a variety of circumstances and world-wide research findings, patient safety andquality care during hospitalization have emerged as major issues. Patient safety deficits may burdenhealth systems as well as allocated resources. The international community has examined severalproposals covering general and systemic aspects in order to improve patient safety; several long-termprograms and strategies have also been implemented promoting the participation of health-relatedagents, and also government agencies and non-governmental organizations.Aim: Those factors that have negative correlations with patient safety and quality healthcare weredetermined; WHO and EU programs as well as the Greek health policy were also reviewed.Method: Local and international literature was reviewed, including EU and WHO official publications,by using the appropriate keywords.Conclusions: International cooperation on patient safety is necessary in order to improvehospitalization and healthcare quality standards. Such incentives depend heavily on establishing worldwideviable and effective health programs and planning. These improvements also require further stepson safe work procedures, environment safety, hazard management, infection control, safe use ofequipment and medication, and sufficient healthcare staff.

  16. A holistic strategy for quality and safety control of traditional Chinese medicines by the “iVarious” standard system

    Directory of Open Access Journals (Sweden)

    Anzhen Chen

    2017-10-01

    Full Text Available An effective quality control system is the key to ensuring the quality, safety and efficacy of traditional Chinese medicines (TCMs. However, the current quality standard research lacks the top-design and systematic design, mostly based on specific technologies or evaluation methods. To resolve the challenges and questions of quality control of TCMs, a brand-new quality standard system, named “iVarious”, was proposed. The system comprises eight elements in a modular format. Meaning of every element was specifically illustrated via corresponding research instances. Furthermore, frankincense study was taken as an example for demonstrating standards and research process, based on the “iVarious” system. This system highlighted a holistic strategy for effectiveness, security, integrity and systematization of quality and safety control standards of TCMs. The establishment of “iVarious” integrates multi-disciplinary technologies and progressive methods, basis elements and key points of standard construction. The system provides a novel idea and technological demonstration for regulation establishment of TCMs quality standards.

  17. The Role Of Quality Assurance Program For Safety Operation Of Nuclear Installations

    International Nuclear Information System (INIS)

    Harjanto, N.T.; Purwadi, K.P.; Boru, D.S.; Farida; Suharni

    2000-01-01

    Nuclear installations expose potential hazard of radiation, therefore in their construction, operation and maintenance, it is necessary to consider safety aspect, in which the safety requirements which has been determined must be met. One of the requirements that is absolutely needed is quality assurance, which covers arrangement of quality assurance program, organization and administration of the implementation of quality assurance, and supervision. Quality Assurance program is a guideline containing quality policies and basic determination on the realization of activities that effect the quality of equipment's and items used in the operation of nuclear installations in order that the operation of nuclear installation can run safety and in accordance with their design aims and operation limits. Quality Assurance Program includes document control, design control, supply control, control of equipment s and items, operation/process control, inspection and control of equipment test, and control of nonconformance and corrections. General system of nuclear installation operation is equipped with safety and supporting systems. These systems must apply the quality assurance program that cover control of activities in the systems. In the implementation of the quality assurance program, it is necessary to establish procedures, work guidelines/instructions, and quality recording that constitutes documents of quality system 2 nd , 3 th , and 4 th level after the quality assurance program. To ensure the effectivity and to prove whether the realization of the program has been pursuant to the determined requirements, an internal audit must be conducted accordingly

  18. Efficacy, safety, quality control, marketing and regulatory guidelines for herbal medicines (phytotherapeutic agents

    Directory of Open Access Journals (Sweden)

    J.B. Calixto

    2000-02-01

    Full Text Available This review highlights the current advances in knowledge about the safety, efficacy, quality control, marketing and regulatory aspects of botanical medicines. Phytotherapeutic agents are standardized herbal preparations consisting of complex mixtures of one or more plants which contain as active ingredients plant parts or plant material in the crude or processed state. A marked growth in the worldwide phytotherapeutic market has occurred over the last 15 years. For the European and USA markets alone, this will reach about $7 billion and $5 billion per annum, respectively, in 1999, and has thus attracted the interest of most large pharmaceutical companies. Insufficient data exist for most plants to guarantee their quality, efficacy and safety. The idea that herbal drugs are safe and free from side effects is false. Plants contain hundreds of constituents and some of them are very toxic, such as the most cytotoxic anti-cancer plant-derived drugs, digitalis and the pyrrolizidine alkaloids, etc. However, the adverse effects of phytotherapeutic agents are less frequent compared with synthetic drugs, but well-controlled clinical trials have now confirmed that such effects really exist. Several regulatory models for herbal medicines are currently available including prescription drugs, over-the-counter substances, traditional medicines and dietary supplements. Harmonization and improvement in the processes of regulation is needed, and the general tendency is to perpetuate the German Commission E experience, which combines scientific studies and traditional knowledge (monographs. Finally, the trend in the domestication, production and biotechnological studies and genetic improvement of medicinal plants, instead of the use of plants harvested in the wild, will offer great advantages, since it will be possible to obtain uniform and high quality raw materials which are fundamental to the efficacy and safety of herbal drugs.

  19. Quality assurance for software important to safety

    International Nuclear Information System (INIS)

    2000-01-01

    Software applications play an increasingly relevant role in nuclear power plant systems. This is particularly true of software important to safety used in both: calculations for the design, testing and analysis of nuclear reactor systems (design, engineering and analysis software); and monitoring, control and safety functions as an integral part of the reactor systems (monitoring, control and safety system software). Computer technology is advancing at a fast pace, offering new possibilities in nuclear reactor design, construction, commissioning, operation, maintenance and decommissioning. These advances also present new issues which must be considered both by the utility and by the regulatory organization. Refurbishment of ageing instrumentation and control systems in nuclear power plants and new safety related application areas have emerged, with direct (e.g. interfaces with safety systems) and indirect (e.g. operator intervention) implications for safety. Currently, there exist several international standards and guides on quality assurance for software important to safety. However, none of the existing documents provides comprehensive guidance to the developer, manager and regulator during all phases of the software life-cycle. The present publication was developed taking into account the large amount of available documentation, the rapid development of software systems and the need for updated guidance on h ow to do it . It provides information and guidance for defining and implementing quality assurance programmes covering the entire life-cycle of software important to safety. Expected users are managers, performers and assessors from nuclear utilities, regulatory bodies, suppliers and technical support organizations involved with the development and use of software applied in nuclear power plants

  20. Leadership, safety climate, and continuous quality improvement: impact on process quality and patient safety.

    Science.gov (United States)

    McFadden, Kathleen L; Stock, Gregory N; Gowen, Charles R

    2014-10-01

    Successful amelioration of medical errors represents a significant problem in the health care industry. There is a need for greater understanding of the factors that lead to improved process quality and patient safety outcomes in hospitals. We present a research model that shows how transformational leadership, safety climate, and continuous quality improvement (CQI) initiatives are related to objective quality and patient safety outcome measures. The proposed framework is tested using structural equation modeling, based on data collected for 204 hospitals, and supplemented with objective outcome data from the Centers for Medicare and Medicaid Services. The results provide empirical evidence that a safety climate, which is connected to the chief executive officer's transformational leadership style, is related to CQI initiatives, which are linked to improved process quality. A unique finding of this study is that, although CQI initiatives are positively associated with improved process quality, they are also associated with higher hospital-acquired condition rates, a measure of patient safety. Likewise, safety climate is directly related to improved patient safety outcomes. The notion that patient safety climate and CQI initiatives are not interchangeable or universally beneficial is an important contribution to the literature. The results confirm the importance of using CQI to effectively enhance process quality in hospitals, and patient safety climate to improve patient safety outcomes. The overall pattern of findings suggests that simultaneous implementation of CQI initiatives and patient safety climate produces greater combined benefits.

  1. Radiation safety and quality control assurance in X-ray diagnostics 1998

    International Nuclear Information System (INIS)

    Servomaa, A.

    1998-03-01

    The report is based on a seminar course of lectures 'Radiation safety and quality assurance in X-ray diagnostics 1998' organized by the Radiation and Nuclear Safety Authority (STUK) in Finland. The lectures included actual information on X-ray examinations: methods of quality assurance, methods of measuring and calculating patient doses, examination frequencies, patient doses, occupational doses, and radiation risks. Paediatric X-ray examinations and interventional procedures were the most specific topics. The new Council Directive 97/43/Euratom on medical exposure, and the European Guidelines on quality criteria for diagnostic radiographic images, were discussed in several lectures. Lectures on general radiation threats and preparedness, examples of radiation accidents, and emergency preparedness in hospitals were also included. (editor)

  2. Sci-Fri AM: Quality, Safety, and Professional Issues 01: CPQR Technical Quality Control Suite Development including Quality Control Workload Results

    Energy Technology Data Exchange (ETDEWEB)

    Malkoske, Kyle; Nielsen, Michelle; Brown, Erika; Diamond, Kevin; Frenière, Normand; Grant, John; Pomerleau-Dalcourt, Natalie; Schella, Jason; Schreiner, L. John; Tantot, Laurent; Barajas, Eduardo Villareal; Bissonnette, Jean-Pierre [Royal Victoria Hospital, Trillium Health Partners, CPQR, Juravinski Cancer Centre, CIUSSS MCQ - CHAUR, Cape Breton Health Care Complex, Centre d’oncologie Dr. Léon-Richard / Dr. Léon Richard Oncology Centre, QEII Health Sciences Centre, Cancer Centre of Southeastern Ontario, Hôpital Maisonneuve-Rosemont, Tom Baker Cancer Centre, Princess Margaret Cancer Centre (Canada)

    2016-08-15

    A close partnership between the Canadian Partnership for Quality Radiotherapy (CPQR) and the Canadian Organization of Medical Physicist’s (COMP) Quality Assurance and Radiation Safety Advisory Committee (QARSAC) has resulted in the development of a suite of Technical Quality Control (TQC) Guidelines for radiation treatment equipment, that outline specific performance objectives and criteria that equipment should meet in order to assure an acceptable level of radiation treatment quality. The framework includes consolidation of existing guidelines and/or literature by expert reviewers, structured stages of public review, external field-testing and ratification by COMP. The adopted framework for the development and maintenance of the TQCs ensures the guidelines incorporate input from the medical physics community during development, measures the workload required to perform the QC tests outlined in each TQC, and remain relevant (i.e. “living documents”) through subsequent planned reviews and updates. This presentation will show the Multi-Leaf Linear Accelerator document as an example of how feedback and cross-national work to achieve a robust guidance document. During field-testing, each technology was tested at multiple centres in a variety of clinic environments. As part of the defined feedback, workload data was captured. This lead to average time associated with testing as defined in each TQC document. As a result, for a medium-sized centre comprising 6 linear accelerators and a comprehensive brachytherapy program, we evaluate the physics workload to 1.5 full-time equivalent physicist per year to complete all QC tests listed in this suite.

  3. Sci-Fri AM: Quality, Safety, and Professional Issues 01: CPQR Technical Quality Control Suite Development including Quality Control Workload Results

    International Nuclear Information System (INIS)

    Malkoske, Kyle; Nielsen, Michelle; Brown, Erika; Diamond, Kevin; Frenière, Normand; Grant, John; Pomerleau-Dalcourt, Natalie; Schella, Jason; Schreiner, L. John; Tantot, Laurent; Barajas, Eduardo Villareal; Bissonnette, Jean-Pierre

    2016-01-01

    A close partnership between the Canadian Partnership for Quality Radiotherapy (CPQR) and the Canadian Organization of Medical Physicist’s (COMP) Quality Assurance and Radiation Safety Advisory Committee (QARSAC) has resulted in the development of a suite of Technical Quality Control (TQC) Guidelines for radiation treatment equipment, that outline specific performance objectives and criteria that equipment should meet in order to assure an acceptable level of radiation treatment quality. The framework includes consolidation of existing guidelines and/or literature by expert reviewers, structured stages of public review, external field-testing and ratification by COMP. The adopted framework for the development and maintenance of the TQCs ensures the guidelines incorporate input from the medical physics community during development, measures the workload required to perform the QC tests outlined in each TQC, and remain relevant (i.e. “living documents”) through subsequent planned reviews and updates. This presentation will show the Multi-Leaf Linear Accelerator document as an example of how feedback and cross-national work to achieve a robust guidance document. During field-testing, each technology was tested at multiple centres in a variety of clinic environments. As part of the defined feedback, workload data was captured. This lead to average time associated with testing as defined in each TQC document. As a result, for a medium-sized centre comprising 6 linear accelerators and a comprehensive brachytherapy program, we evaluate the physics workload to 1.5 full-time equivalent physicist per year to complete all QC tests listed in this suite.

  4. Assuring fish safety and quality in international fish trade

    International Nuclear Information System (INIS)

    Ababouch, Lahsen . E-mail lahsen.ababouch@fao.org

    2006-01-01

    International trade in fishery commodities reached US$ 58.2 billion in 2002, a 5% improvement relative to 2000 and a 45% increase over 1992 levels. Within this global trade, developing countries registered a net trade surplus of US$ 17.4 billion in 2002 and accounted for almost 50% by value and 55% of fish exports by volume. This globalization of fish trade, coupled with technological developments in food production, handling, processing and distribution, and the increasing awareness and demand of consumers for safe and high quality food have put food safety and quality assurance high in public awareness and a priority for many governments. Consequently, many countries have tightened food safety controls, imposing additional costs and requirements on imports. As early as 1980, there was an international drive towards adopting preventative HACCP-based safety and quality systems. More recently, there has been a growing awareness of the importance of an integrated, multidisciplinary approach to food safety and quality throughout the entire food chain. Implementation of this approach requires an enabling policy and regulatory environment at national and international levels with clearly defined rules and standards, establishment of appropriate food control systems and programmes at national and local levels, and provision of appropriate training and capacity building. This paper discusses the international framework for fish safety and quality, with particular emphasis on the United Nation's Food and Agricultural Organization's (FAO) strategy to promote international harmonization and capacity building

  5. Assuring fish safety and quality in international fish trade

    Energy Technology Data Exchange (ETDEWEB)

    Ababouch, Lahsen [United Nations, Food and Agricultural Organization, Chief, Fish Utilization and Marketing Services, FAO Headquarters, F-607 Rome (Italy)]. E-mail lahsen.ababouch@fao.org

    2006-07-01

    International trade in fishery commodities reached US$ 58.2 billion in 2002, a 5% improvement relative to 2000 and a 45% increase over 1992 levels. Within this global trade, developing countries registered a net trade surplus of US$ 17.4 billion in 2002 and accounted for almost 50% by value and 55% of fish exports by volume. This globalization of fish trade, coupled with technological developments in food production, handling, processing and distribution, and the increasing awareness and demand of consumers for safe and high quality food have put food safety and quality assurance high in public awareness and a priority for many governments. Consequently, many countries have tightened food safety controls, imposing additional costs and requirements on imports. As early as 1980, there was an international drive towards adopting preventative HACCP-based safety and quality systems. More recently, there has been a growing awareness of the importance of an integrated, multidisciplinary approach to food safety and quality throughout the entire food chain. Implementation of this approach requires an enabling policy and regulatory environment at national and international levels with clearly defined rules and standards, establishment of appropriate food control systems and programmes at national and local levels, and provision of appropriate training and capacity building. This paper discusses the international framework for fish safety and quality, with particular emphasis on the United Nation's Food and Agricultural Organization's (FAO) strategy to promote international harmonization and capacity building.

  6. [Establishment of Quality Control System of Nucleic Acid Detection for Ebola Virus in Sierra Leone-China Friendship Biological Safety Laboratory].

    Science.gov (United States)

    Wang, Qin; Zhang, Yong; Nie, Kai; Wang, Huanyu; Du, Haijun; Song, Jingdong; Xiao, Kang; Lei, Wenwen; Guo, Jianqiang; Wei, Hejiang; Cai, Kun; Wang, Yanhai; Wu, Jiang; Gerald, Bangura; Kamara, Idrissa Laybohr; Liang, Mifang; Wu, Guizhen; Dong, Xiaoping

    2016-03-01

    The quality control process throughout the Ebola virus nucleic acid detection in Sierra Leone-China Friendship Biological Safety Laboratory (SLE-CHN Biosafety Lab) was described in detail, in order to comprehensively display the scientific, rigorous, accurate and efficient practice in detection of Ebola virus of first batch detection team in SLE-CHN Biosafety Lab. Firstly, the key points of laboratory quality control system was described, including the managements and organizing, quality control documents and information management, instrument, reagents and supplies, assessment, facilities design and space allocation, laboratory maintenance and biosecurity. Secondly, the application of quality control methods in the whole process of the Ebola virus detection, including before the test, during the test and after the test, was analyzed. The excellent and professional laboratory staffs, the implementation of humanized management are the cornerstone of the success; High-level biological safety protection is the premise for effective quality control and completion of Ebola virus detection tasks. And professional logistics is prerequisite for launching the laboratory diagnosis of Ebola virus. The establishment and running of SLE-CHN Biosafety Lab has landmark significance for the friendship between Sierra Leone and China, and the lab becomes the most important base for Ebola virus laboratory testing in Sierra Leone.

  7. Application of Proteomics in Food Technology and Food Biotechnology: Process Development, Quality Control and Product Safety

    Directory of Open Access Journals (Sweden)

    Dajana Gašo-Sokač

    2010-01-01

    Full Text Available Human food is a very complex biological mixture and food processing and safety are very important and essential disciplines. Proteomics technology using different high-performance separation techniques such as two-dimensional gel electrophoresis, one-dimensional and multidimensional chromatography, combined with high-resolution mass spectrometry has the power to monitor the protein composition of foods and their changes during the production process. The use of proteomics in food technology is presented, especially for characterization and standardization of raw materials, process development, detection of batch-to-batch variations and quality control of the final product. Further attention is paid to the aspects of food safety, especially regarding biological and microbial safety and the use of genetically modified foods.

  8. Safety culture and quality management of Kartini research reactor

    International Nuclear Information System (INIS)

    Syarip; Hauptmanns, Ulrich

    1999-01-01

    The evaluation for assessing the safety culture and quality of safety management of Kartini research reactor is presented. The method is based on the concept of management control of safety (audit) as well as by using the developed method i.e. the questionnaires concerning areas of relevance which have to be answered with value statements. There are seven statements or qualifiers in answering the questions. Since such statements are vague, they are represented by fuzzy numbers. The weaknesses can be identified from the different areas contemplated. The evaluation result show that the quality of safety management of Kartini research reactor is globally rated as 'Average'. The operator behavior in the implementation of 'safety culture' concept is found as a weakness, therefore this area should be improved. (author)

  9. Safety culture and quality management of Kartini research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Syarip [Yogyakarta Nuclear Research Centre, Yogyakarta (Indonesia); Hauptmanns, Ulrich [Department of Plant Design and Safety, Otto-Von-Guericke-University, Magdeburg (Germany)

    1999-10-01

    The evaluation for assessing the safety culture and quality of safety management of Kartini research reactor is presented. The method is based on the concept of management control of safety (audit) as well as by using the developed method i.e. the questionnaires concerning areas of relevance which have to be answered with value statements. There are seven statements or qualifiers in answering the questions. Since such statements are vague, they are represented by fuzzy numbers. The weaknesses can be identified from the different areas contemplated. The evaluation result show that the quality of safety management of Kartini research reactor is globally rated as 'Average'. The operator behavior in the implementation of 'safety culture' concept is found as a weakness, therefore this area should be improved. (author)

  10. Software Quality Assurance for Nuclear Safety Systems

    International Nuclear Information System (INIS)

    Sparkman, D R; Lagdon, R

    2004-01-01

    The US Department of Energy has undertaken an initiative to improve the quality of software used to design and operate their nuclear facilities across the United States. One aspect of this initiative is to revise or create new directives and guides associated with quality practices for the safety software in its nuclear facilities. Safety software includes the safety structures, systems, and components software and firmware, support software and design and analysis software used to ensure the safety of the facility. DOE nuclear facilities are unique when compared to commercial nuclear or other industrial activities in terms of the types and quantities of hazards that must be controlled to protect workers, public and the environment. Because of these differences, DOE must develop an approach to software quality assurance that ensures appropriate risk mitigation by developing a framework of requirements that accomplishes the following goals: (sm b ullet) Ensures the software processes developed to address nuclear safety in design, operation, construction and maintenance of its facilities are safe (sm b ullet) Considers the larger system that uses the software and its impacts (sm b ullet) Ensures that the software failures do not create unsafe conditions Software designers for nuclear systems and processes must reduce risks in software applications by incorporating processes that recognize, detect, and mitigate software failure in safety related systems. It must also ensure that fail safe modes and component testing are incorporated into software design. For nuclear facilities, the consideration of risk is not necessarily sufficient to ensure safety. Systematic evaluation, independent verification and system safety analysis must be considered for software design, implementation, and operation. The software industry primarily uses risk analysis to determine the appropriate level of rigor applied to software practices. This risk-based approach distinguishes safety

  11. Efficiency of the functioning of the state control system for the safety and quality of animal products in Ukraine

    Directory of Open Access Journals (Sweden)

    I. Kyryliuk

    2017-12-01

    Full Text Available The study reveals the results of evaluating the effectiveness of the state control system (supervision on the safety and individual indicators of the quality of livestock products in Ukraine. The necessity of application of such components of efficiency as legislation, management and its organizational structure, inspection and laboratory service, information, training and communications is substantiated. It has been determined that during a sufficiently long period of time (until 2015, the system of state control (supervision was archaic and actually focused on the principles of command and administrative economy. The modern tendencies and specifics of the improvement of the Ukrainian control system in the direction of its harmonization with the European one are shown. The emphasis was on significant volumes of work that needed to be done in a very short time, as well as in the absence of adequate funding and appropriate skilled specialists. The emergence of clarity and unambiguousness in determining the responsibility of market operators for violating the legislation requirements in the field of production and circulation of animal origin food products was emphasized. Along with the achievements, there were identified systemic problems related to the technical regulation of safety assurance processes and individual quality indicators in Ukraine. Also it was noted and revealed that legislation in the area of guaranteeing the quality and safety of livestock products in Ukraine remains incomplete and not fully developed. The necessity of development of a number of by-laws and allocation of necessary financing for effective functioning of the state control system over product safety is substantiated. Article specified on the presence of insufficient number of professional inspection and laboratory services is underlined. The mechanisms of avoiding corruption risks and excessive pressure on the subjects of the livestock production market are

  12. The influence of farmland pollution on the quality and safety of agricultural products

    Science.gov (United States)

    Ma, Z. L.; Li, L. Y.; Ye, C.; Lin, X. Y.; B, C.; Wei

    2018-02-01

    The quality and safety of agricultural products is not only a major livelihood issues for people’s health, but also the main barriers to international trade of agricultural products nowadays. The soil is the foundation to the production of agricultural products and the guarantee of agricultural development. The farmland soil quality is directly related to the quality and safety of agricultural products. Our country’s soil has been polluted by a series of pollution, Such as the excessive discharge of industrial wastes, the encroachment of household waste, and the unreasonable use of pesticides and fertilizers. Soil degradation is a serious threat to the quality and safety of agricultural products, so eliminating soil degradation is the fundamental way out for quality and safety of agricultural products. By analyzing problems of the quality and safety of agricultural products in our country, and exploring the farmland soil influence on the quality and safety of agricultural products. This article provides a reference for improving the control level of quality and safety of agricultural products and the farmland soil quality.

  13. Process safety improvement-Quality and target zero

    Energy Technology Data Exchange (ETDEWEB)

    Van Scyoc, Karl [Det Norske Veritas (U.S.A.) Inc., DNV Energy Solutions, 16340 Park Ten Place, Suite 100, Houston, TX 77084 (United States)], E-mail: karl.van.scyoc@dnv.com

    2008-11-15

    Process safety practitioners have adopted quality management principles in design of process safety management systems with positive effect, yet achieving safety objectives sometimes remain a distant target. Companies regularly apply tools and methods which have roots in quality and productivity improvement. The 'plan, do, check, act' improvement loop, statistical analysis of incidents (non-conformities), and performance trending popularized by Dr. Deming are now commonly used in the context of process safety. Significant advancements in HSE performance are reported after applying methods viewed as fundamental for quality management. In pursuit of continual process safety improvement, the paper examines various quality improvement methods, and explores how methods intended for product quality can be additionally applied to continual improvement of process safety. Methods such as Kaizen, Poke yoke, and TRIZ, while long established for quality improvement, are quite unfamiliar in the process safety arena. These methods are discussed for application in improving both process safety leadership and field work team performance. Practical ways to advance process safety, based on the methods, are given.

  14. Process safety improvement-Quality and target zero

    International Nuclear Information System (INIS)

    Van Scyoc, Karl

    2008-01-01

    Process safety practitioners have adopted quality management principles in design of process safety management systems with positive effect, yet achieving safety objectives sometimes remain a distant target. Companies regularly apply tools and methods which have roots in quality and productivity improvement. The 'plan, do, check, act' improvement loop, statistical analysis of incidents (non-conformities), and performance trending popularized by Dr. Deming are now commonly used in the context of process safety. Significant advancements in HSE performance are reported after applying methods viewed as fundamental for quality management. In pursuit of continual process safety improvement, the paper examines various quality improvement methods, and explores how methods intended for product quality can be additionally applied to continual improvement of process safety. Methods such as Kaizen, Poke yoke, and TRIZ, while long established for quality improvement, are quite unfamiliar in the process safety arena. These methods are discussed for application in improving both process safety leadership and field work team performance. Practical ways to advance process safety, based on the methods, are given

  15. Process safety improvement--quality and target zero.

    Science.gov (United States)

    Van Scyoc, Karl

    2008-11-15

    Process safety practitioners have adopted quality management principles in design of process safety management systems with positive effect, yet achieving safety objectives sometimes remain a distant target. Companies regularly apply tools and methods which have roots in quality and productivity improvement. The "plan, do, check, act" improvement loop, statistical analysis of incidents (non-conformities), and performance trending popularized by Dr. Deming are now commonly used in the context of process safety. Significant advancements in HSE performance are reported after applying methods viewed as fundamental for quality management. In pursuit of continual process safety improvement, the paper examines various quality improvement methods, and explores how methods intended for product quality can be additionally applied to continual improvement of process safety. Methods such as Kaizen, Poke yoke, and TRIZ, while long established for quality improvement, are quite unfamiliar in the process safety arena. These methods are discussed for application in improving both process safety leadership and field work team performance. Practical ways to advance process safety, based on the methods, are given.

  16. Quality and safety in Spain

    International Nuclear Information System (INIS)

    Prieto Barrio, J. M.; Martinez Martin, D. J.

    2015-01-01

    For three decades, and after the entry of Spain into the EU, it has been developed a regulatory, stable but evolving, framework that has allowed to create the conditions and structures to have stringent safety conditions of products and manufacturing facilities, as well as all the activities necessary for their certification and control. This development has been possible, among others, by the work of impulse and coordination of the Ministry of industry, Energy and Tourism, and particularly of the quality and Industrial safety sub directorate. On the other hand it has been developed a quality infrastructure that has, at the State level, with a standardisation (AENOR) entity and an accreditation body (ENAC) with recognized prestige around the world. In this article, in the first part, a list the regulations which apply to products and manufacturing facilities is shown, as well as explain the role played by standards and accreditation system in industrial safety and the factor of competitiveness that this entails for our industrial sector, and, in the second part, the institutional role of the Ministry and, the aforementioned Sub directorate, is described. The aim of the article is to be a descriptive reference of the current regulatory framework as well as the role of the State in this process. (Author)

  17. Quality and safety in radiotherapy

    CERN Document Server

    Pawlicki, Todd

    2010-01-01

    The first text to focus solely on quality and safety in radiotherapy, this work encompasses not only traditional, more technically oriented, quality assurance activities, but also general approaches of quality and safety. It includes contributions from experts both inside and outside the field to present a global view. The task of assuring quality is no longer viewed solely as a technical, equipment-dependent endeavor. Instead, it is now recognized as depending on both the processes and the people delivering the service. Divided into seven broad categories, the text covers: Quality Management

  18. Social but safe? Quality and safety of diabetes-related online social networks.

    Science.gov (United States)

    Weitzman, Elissa R; Cole, Emily; Kaci, Liljana; Mandl, Kenneth D

    2011-05-01

    To foster informed decision-making about health social networking (SN) by patients and clinicians, the authors evaluated the quality/safety of SN sites' policies and practices. Multisite structured observation of diabetes-focused SN sites. Measurements 28 indicators of quality and safety covering: (1) alignment of content with diabetes science and clinical practice recommendations; (2) safety practices for auditing content, supporting transparency and moderation; (3) accessibility of privacy policies and the communication and control of privacy risks; and (4) centralized sharing of member data and member control over sharing. Quality was variable across n=10 sites: 50% were aligned with diabetes science/clinical practice recommendations with gaps in medical disclaimer use (30% have) and specification of relevant glycosylated hemoglobin levels (0% have). Safety was mixed with gaps in external review approaches (20% used audits and association links) and internal review approaches (70% use moderation). Internal safety review offers limited protection: misinformation about a diabetes 'cure' was found on four moderated sites. Of nine sites with advertising, transparency was missing on five; ads for unfounded 'cures' were present on three. Technological safety was poor with almost no use of procedures for secure data storage and transmission; only three sites support member controls over personal information. Privacy policies' poor readability impedes risk communication. Only three sites (30%) demonstrated better practice. Limitations English-language diabetes sites only. The quality/safety of diabetes SN is variable. Observed better practice suggests improvement is feasible. Mechanisms for improvement are recommended that engage key stakeholders to balance autonomy, community ownership, conditions for innovation, and consumer protection.

  19. Software quality assurance for safety analysis and risk management at the Savannah River Site

    International Nuclear Information System (INIS)

    Ades, M.J.; Toffer, H.; Crowe, R.D.

    1991-01-01

    As part of its Reactor Operations Improvement Program at the Savannah River Site (SRS), Westinghouse Savannah River Company (WSRC), in cooperation with the Westinghouse Hanford Company, has developed and implemented quality assurance for safety-related software for technical programs essential to the safety and reliability of reactor operations. More specifically, the quality assurance process involved the development and implementation of quality standards and attendant procedures based on industry software quality standards. These procedures were then applied to computer codes in reactor safety and probabilistic risk assessment analyses. This paper provides a review of the major aspects of the WSRC safety-related software quality assurance. In particular, quality assurance procedures are described for the different life cycle phases of the software that include the Requirements, Software Design and Implementation, Testing and Installation, Operation and Maintenance, and Retirement Phases. For each phase, specific provisions are made to categorize the range of activities, the level of responsibilities, and the documentation needed to assure the control of the software. The software quality assurance procedures developed and implemented are evolutionary in nature, and thus, prone to further refinements. These procedures, nevertheless, represent an effective controlling tool for the development, production, and operation of safety-related software applicable to reactor safety and probabilistic risk assessment analyses

  20. Study on Food Quality and Safety Management Based on Hotel Management

    Directory of Open Access Journals (Sweden)

    Shi Zengye

    2017-12-01

    Full Text Available In recent years, with the frequent occurrence of food safety problems, people have begun to pay attention to food safety, especially the food safety of hotels. This paper proposed a Hazard Analysis and Critical Control Point (HACCP management system to analyze food safety issues of hotels in order to improve the food quality and safety in hotel management. Through the practical application of the HACCP management system in the hotel catering industry, it was found that the amount of bacteria greatly reduced and the pass rate of tableware disinfection increased significantly in the hotel's food processing links, while customer satisfaction greatly improved. Therefore, the HACCP management system had great applicability in improving the food quality and safety of hotels.

  1. Quality Control and Quality Assurance of Radiation Oncology

    International Nuclear Information System (INIS)

    Abaza, A.

    2016-01-01

    Radiotherapy (RT) has played important roles in cancer treatment for more than one century. The development of RT techniques allows high-dose irradiation to tumors while reducing the radiation doses delivered to surrounding normal tissues. However, RT is a complex process and involves understanding of the principles of medical physics, radiobiology, radiation safety, dosimetry, radiation treatment planning, simulation and interaction of radiation with other treatment modalities. Each step in the integrated process of RT needs quality control and quality assurance (QA) to prevent errors and to ensure that patients will receive the prescribed treatment correctly. The aim of this study is to help the radio therapists in identifying a system for QA that balances patient safety and quality with available resources. Recent advances in RT focus on the need for a systematic RT QA program that balances patient safety and quality with available resources. It is necessary to develop more formal error mitigation and process analysis methods, such as failure mode and effect analysis (FMEA), to focus available QA resources optimally on the process components. External audit programs are also effective. Additionally, Clinical trial QA has a significant role in enhancing the quality of care. The International Atomic Energy Agency (IAEA) has operated both an on-site and off-site postal dosimetry audit to improve practice and to assure the dose from RT equipment. Both postal dosimetry audit and clinical trial RTQA, especially for advanced technologies, in collaboration with global networks, will serve to enhance patient safety and quality of care

  2. Control of quality in mammography

    International Nuclear Information System (INIS)

    2006-10-01

    The present protocol of quality control/quality assurance in mammography is the result of the work of two regional projects realised in Latin America within the frame of ARCAL with the support of the IAEA. The first is ARCAL LV (RLA/6/043) project on quality assurance/quality control in mammography studies which analysed the present situation of the mammography in the member countries of the project which include: Bolivia, Colombia, Costa Rica, Cuba, El Salvador, Guatemala, Nicaragua, Panama, Paraguay, Peru, Dominican Republic and Republic of Venezuela and the second is ARCAL XLIX (RLA/9/035) project, whose members were Brazil, Colombia, Cuba, Chile, Mexico, and Peru, worked the application of Basic Safety Standards for the protection against ionising radiation with the aim to improve radiation protection in X-ray diagnosis medical practices through the implementation of the Basic Safety Standards (BSS) related to x-ray diagnosis in selected hospitals located in each country involved in the project. The work of both projects had been consolidated and harmonized in the present publication

  3. Study on Food Quality and Safety Management Based on Hotel Management

    OpenAIRE

    Shi Zengye

    2017-01-01

    In recent years, with the frequent occurrence of food safety problems, people have begun to pay attention to food safety, especially the food safety of hotels. This paper proposed a Hazard Analysis and Critical Control Point (HACCP) management system to analyze food safety issues of hotels in order to improve the food quality and safety in hotel management. Through the practical application of the HACCP management system in the hotel catering industry, it was found that the amount of bacteria...

  4. Documents pertaining to safety control of nuclear facilities

    International Nuclear Information System (INIS)

    1998-01-01

    The Finnish Radiation and Nuclear Safety Authority (STUK) controls the safety of nuclear facilities in Finland. This control encompasses on one hand the evaluation of plant safety on the basis of plans and analyses pertaining to the plant and on the other hand the inspection of plant structures, systems and components as well as of operational activity. STUK also monitors plants operational experience feedback and technical developments in the field, as well as the development of safety research and takes the necessary measures on their basis. Guide YVL 1.1 describes how STUK controls the design, construction and operation of nuclear power plants. The documents to be submitted to STUK are described in the nuclear energy legislation and YVL guides. This guide presents the mode of delivery, quality, contents and number of documents to be submitted to STUK

  5. NAVIGATING A QUALITY ROUTE TO A NATIONAL SAFETY AWARD

    Energy Technology Data Exchange (ETDEWEB)

    PREVETTE SS

    2009-05-26

    Deming quality methodologies applied to safety are recognized with the National Safety Council's annual Robert W. Campbell Award. Over the last ten years, the implementation of Statistical Process Control and quality methodologies at the U.S. Department of Energy's Hanford Site have contributed to improved safety. Improvements attributed to Statistical Process Control are evidenced in Occupational Safety and Health records and documented through several articles in Quality Progress and the American Society of Safety Engineers publication, Professional Safety. Statistical trending of safety, quality, and occurrence data continues to playa key role in improving safety and quality at what has been called the world's largest environmental cleanup project. DOE's Hanford Site played a pivotal role in the nation's defense beginning in the 1940s, when it was established as part of the Manhattan Project. After more than 50 years of producing material for nuclear weapons, Hanford, which covers 586 square miles in southeastern Washington state, is now focused on three outcomes: (1) Restoring the Columbia River corridor for multiple uses; (2) Transitioning the central plateau to support long-term waste management; and (3) Putting DOE assets to work for the future. The current environmental cleanup mission faces challenges of overlapping technical, political, regulatory, environmental, and cultural interests. From Oct. 1, 1996 through Sept. 30, 2008, Fluor Hanford was a prime contractor to the Department of Energy's Richland Operations Office. In this role, Fluor Hanford managed several major cleanup activities that included dismantling former nuclear-processing facilities, cleaning up the Site's contaminated groundwater, retrieving and processing transuranic waste for shipment and disposal off-site, maintaining the Site's infrastructure, providing security and fire protection, and operating the Volpentest HAMMER Training and Education

  6. Quality and safety control in the production of recreational-purpose cottage cheese

    OpenAIRE

    Мостова, Людмила Миколаївна; Клусович, Тетяна Валеріївна

    2015-01-01

    The paper deals with the relevant problem of implementing safety control systems according to HACCP principles for Ukrainian catering establishments in the integration of trade space. Taking into account high competition and consumer audience gaining priority, the work emphasizes the need to develop and implement safety control system according to HACCP principles as a precondition for leadership of catering establishments  in the national market, and get significant competitive advantages in...

  7. 2011 John M. Eisenberg Patient Safety and Quality Awards. The effect of a novel Housestaff Quality Council on quality and patient safety. Innovation in patient safety and quality at the local level.

    Science.gov (United States)

    Fleischut, Peter M; Faggiani, Susan L; Evans, Adam S; Brenner, Samantha; Liebowitz, Richard S; Forese, Laura; Kerr, Gregory E; Lazar, Eliot J

    2012-07-01

    In 2008 New York-Presbyterian Hospital (NYP)/Weill Cornell Medical Center, New York City, the largest not-for-profit, nonsectarian hospital in the United States, created and implemented a novel approach--the Housestaff Quality Council (HQC)--to engaging house-staff in quality and patient safety activities. The HQC represented an innovative collaboration between the housestaff, the Department of Anesthesiology, the Division of Quality and Patient Safety, the Office of Graduate Medical Education, and senior leadership. As key managers of patient care, the housestaff sought to become involved in the quality and patient safety decision- and policy-making processes at the hospital. Its members were determined to decrease or minimize adverse events by facilitating multimodal communication, ensuring smart work flow, and measuring outcomes to determine best practices. The HQC, which also included frontline hospital staff or managers from areas such as nursing, pharmacy, and information technology, aligned its initiatives with those of the division of quality and patient safety and embarked on two projects--medication reconciliation and use of the electronic medical record. More than three years later, the resulting improvements have been sustained and three new projects--hand hygiene, central line-associated bloodstream infections, and patient handoffs--have been initiated. The HQC model is highly replicable at other teaching institutions as a complementary approach to their other quality and patient safety initiatives. However, the ability to sustain positive momentum is dependent on the ability of residents to invest time and effort in the face of a demanding residency training schedule and focus on specialty-specific clinical and research activities.

  8. Quality control of three main materials for civil construction of nuclear power plant

    International Nuclear Information System (INIS)

    Wang Feng

    2011-01-01

    The construction and operation of nuclear power plant is a systematic engineering. To ensure quality and safety of nuclear power plants, each work from design to operation can have certain impact on the quality and safety of the project. The quality of each related work shall be controlled. Starting from the quality control over raw materials for the civil construction of nuclear power plant, this article mainly analyzes how to control the quality and manage the three main materials of steel, concrete and modular parts in the civil construction. (author)

  9. The 7 basic tools of quality applied to radiological safety

    International Nuclear Information System (INIS)

    Gonzalez F, J.A.

    1991-01-01

    This work seeks to establish a series of correspondences among the search of the quality and the optimization of the doses received by the occupationally exposed personnel. There are treated about the seven basic statistic tools of the quality: the Pareto technique, Cause effect diagrams, Stratification, Verification sheet, Histograms, Dispersion diagrams and Graphics and control frames applied to the Radiological Safety

  10. Food quality and safety: Consumer perception and demand

    DEFF Research Database (Denmark)

    Grunert, Klaus G.

    2005-01-01

    choice and consumer demand, addressing questions of price perception and the validity of willingness-to-pay measurements. It is concluded that food quality and safety are central issues in today's food economics, though many research questions remain to be addressed. Udgivelsesdato: SEP 1......Research on consumer quality perception is reviewed using the Total Food Quality Model as a structuring device. The relationship between food safety and quality is addressed, and is discussed in the context of research on consumer risk perception. Quality and safety perception is linked to food...

  11. Food quality and safety: Consumer perception and demand

    DEFF Research Database (Denmark)

    Grunert, Klaus G.

    2005-01-01

    Research on consumer quality perception is reviewed using the Total Food Quality Model as a structuring device. The relationship between food safety and quality is addressed, and is discussed in the context of research on consumer risk perception. Quality and safety perception is linked to food...... choice and consumer demand, addressing questions of price perception and the validity of willingness-to-pay measurements. It is concluded that food quality and safety are central issues in today's food economics, though many research questions remain to be addressed. Udgivelsesdato: SEP 1...

  12. Safety regulations concerning instrumentation and control systems for research reactors

    International Nuclear Information System (INIS)

    El-Shanshoury, A.I.

    2009-01-01

    A brief study on the safety and reliability issues related to instrumentation and control systems in nuclear reactor plants is performed. In response, technical and strategic issues are used to accomplish instrumentation and control systems safety. For technical issues there are ; systems aspects of digital I and C technology, software quality assurance, common-mode software, failure potential, safety and reliability assessment methods, and human factors and human machine interfaces. The strategic issues are the case-by-case licensing process and the adequacy of the technical infrastructure. The purpose of this work was to review the reliability of the safety systems related to these technical issues for research reactors

  13. Performance Testing Methodology for Safety-Critical Programmable Logic Controller

    International Nuclear Information System (INIS)

    Kim, Chang Ho; Oh, Do Young; Kim, Ji Hyeon; Kim, Sung Ho; Sohn, Se Do

    2009-01-01

    The Programmable Logic Controller (PLC) for use in Nuclear Power Plant safety-related applications is being developed and tested first time in Korea. This safety-related PLC is being developed with requirements of regulatory guideline and industry standards for safety system. To test that the quality of the developed PLC is sufficient to be used in safety critical system, document review and various product testings were performed over the development documents for S/W, H/W, and V/V. This paper provides the performance testing methodology and its effectiveness for PLC platform conducted by KOPEC

  14. Layoffs and tradeoffs: production, quality, and safety demands under the threat of job loss.

    Science.gov (United States)

    Probst, Tahira M

    2002-07-01

    Employees often face a conflict between production targets, quality assurance, and adherence to safety policies. In a time when layoffs are on the rise, it is important to understand the effects of employee job insecurity on these potentially competing demands. A laboratory experiment manipulated the threat of layoffs in a simulated organization and assessed its effect on employee productivity, product quality, and adherence to safety policies. Results suggest that student participants faced with the threat of layoffs were more productive, yet violated more safety rules and produced lower quality outputs, than participants in the control condition. Implications for organizations contemplating layoffs and directions for future research are discussed.

  15. Informatization of items quality control for NI in nuclear power plant

    International Nuclear Information System (INIS)

    Zhang Jiankui; Zang Baiqi

    2010-01-01

    Design ideas, implementation methods and some key techniques for item quality control of NI in nuclear power plant are illustrated in this article according to item quality management mode. The item quality control method can improve the quality of NI, ensure the safety and lower the construction and operation cost of nuclear power plant. (authors)

  16. Model quality and safety studies

    DEFF Research Database (Denmark)

    Petersen, K.E.

    1997-01-01

    The paper describes the EC initiative on model quality assessment and emphasizes some of the problems encountered in the selection of data from field tests used in the evaluation process. Further, it discusses the impact of model uncertainties in safety studies of industrial plants. The model...... that most of these have never been through a procedure of evaluation, but nonetheless are used to assist in making decisions that may directly affect the safety of the public and the environment. As a major funder of European research on major industrial hazards, DGXII is conscious of the importance......-tain model is appropriate for use in solving a given problem. Further, the findings from the REDIPHEM project related to dense gas dispersion will be highlighted. Finally, the paper will discuss the need for model quality assessment in safety studies....

  17. IAEA code and safety guides on quality assurance

    International Nuclear Information System (INIS)

    Raisic, N.

    1980-01-01

    In the framework of its programme in safety standards development, the IAEA has recently published a Code of Practice on Quality Assurance for Safety in Nuclear Power Plants. The Code establishes minimum requirements for quality assurance which Member States should use in the context of their own nuclear safety requirements. A series of 10 Safety Guides which describe acceptable methods of implementing the requirements of specific sections of the Code are in preparation. (orig.)

  18. Quality and Safety as a Core Leadership Competency.

    Science.gov (United States)

    Bleich, Michael R

    2018-05-01

    A leader's toolbox of competencies comprises knowledge, skills, and abilities in clinical care, finance, human resource management, and more. As essential as these are, a strong command of quality and safety competencies is sovereign in leading and managing, ensuring an optimal patient experience. Four core areas of quality and safety competencies are presented: systems science, knowledge workers, implementation science and big data, and quality safety tools and techniques. J Contin Educ Nurs. 2018;49(5):200-202. Copyright 2018, SLACK Incorporated.

  19. Radiation safety and quality control assurance in X-ray diagnostics 1998; Saeteilyturvallisuus ja laadunvarmistus roentgendiagnostiikassa 1998

    Energy Technology Data Exchange (ETDEWEB)

    Servomaa, A [ed.

    1998-03-01

    The report is based on a seminar course of lectures `Radiation safety and quality assurance in X-ray diagnostics 1998` organized by the Radiation and Nuclear Safety Authority (STUK) in Finland. The lectures included actual information on X-ray examinations: methods of quality assurance, methods of measuring and calculating patient doses, examination frequencies, patient doses, occupational doses, and radiation risks. Paediatric X-ray examinations and interventional procedures were the most specific topics. The new Council Directive 97/43/Euratom on medical exposure, and the European Guidelines on quality criteria for diagnostic radiographic images, were discussed in several lectures. Lectures on general radiation threats and preparedness, examples of radiation accidents, and emergency preparedness in hospitals were also included. (editor)

  20. Implementation of Programmatic Quality and the Impact on Safety

    Science.gov (United States)

    Huls, Dale Thomas; Meehan, Kevin

    2005-01-01

    The purpose of this paper is to discuss the implementation of a programmatic quality assurance discipline within the International Space Station Program and the resulting impact on safety. NASA culture has continued to stress safety at the expense of quality when both are extremely important and both can equally influence the success or failure of a Program or Mission. Although safety was heavily criticized in the media after Colimbiaa, strong case can be made that it was the failure of quality processes and quality assurance in all processes that eventually led to the Columbia accident. Consequently, it is possible to have good quality processes without safety, but it is impossible to have good safety processes without quality. The ISS Program quality assurance function was analyzed as representative of the long-term manned missions that are consistent with the President s Vision for Space Exploration. Background topics are as follows: The quality assurance organizational structure within the ISS Program and the interrelationships between various internal and external organizations. ISS Program quality roles and responsibilities with respect to internal Program Offices and other external organizations such as the Shuttle Program, JSC Directorates, NASA Headquarters, NASA Contractors, other NASA Centers, and International Partner/participants will be addressed. A detailed analysis of implemented quality assurance responsibilities and functions with respect to NASA Headquarters, the JSC S&MA Directorate, and the ISS Program will be presented. Discussions topics are as follows: A comparison of quality and safety resources in terms of staffing, training, experience, and certifications. A benchmark assessment of the lessons learned from the Columbia Accident Investigation (CAB) Report (and follow-up reports and assessments), NASA Benchmarking, and traditional quality assurance activities against ISS quality procedures and practices. The lack of a coherent operational

  1. Methods for the computerized control of nuclear power plants for improved safety, quality, and productivity

    International Nuclear Information System (INIS)

    Heising, C.D.

    1988-12-01

    The purpose of this research project was to translate the Total Quality Control (TQC) management system to the operation of nuclear power plants. This work began on September 30, 1986 and continued through December 30, 1988 at an original funding level of $251,000. Four graduate research assistants were employed during the two year project period, with all four completing master's level degree theses or projects. In addition, several papers were presented at technical conferences regarding this work. Currently, one paper has been accepted for publication in the journal of Operations Research, and two more papers are currently being written for submission in the near future. The project also received favorable publicity at the university and elsewhere. The major findings of this work was that, indeed, the Japanese management system of Total Quality Control (TQC) may be applied to nuclear power plant operation to achieve enhanced safety and increased efficiency. Two utilities are already heavily engaged in implementing TQC at their nuclear power plants: the Kansai Electric Company of Osaka, Japan and the Florida Power and Light Company of Miami, Florida. We have documented in detail the progress of these utilities in their attempts to implement TQC, as well as highlighting ''success stories'' of TQC implementation in other industries

  2. Improving patient safety through quality assurance.

    Science.gov (United States)

    Raab, Stephen S

    2006-05-01

    Anatomic pathology laboratories use several quality assurance tools to detect errors and to improve patient safety. To review some of the anatomic pathology laboratory patient safety quality assurance practices. Different standards and measures in anatomic pathology quality assurance and patient safety were reviewed. Frequency of anatomic pathology laboratory error, variability in the use of specific quality assurance practices, and use of data for error reduction initiatives. Anatomic pathology error frequencies vary according to the detection method used. Based on secondary review, a College of American Pathologists Q-Probes study showed that the mean laboratory error frequency was 6.7%. A College of American Pathologists Q-Tracks study measuring frozen section discrepancy found that laboratories improved the longer they monitored and shared data. There is a lack of standardization across laboratories even for governmentally mandated quality assurance practices, such as cytologic-histologic correlation. The National Institutes of Health funded a consortium of laboratories to benchmark laboratory error frequencies, perform root cause analysis, and design error reduction initiatives, using quality assurance data. Based on the cytologic-histologic correlation process, these laboratories found an aggregate nongynecologic error frequency of 10.8%. Based on gynecologic error data, the laboratory at my institution used Toyota production system processes to lower gynecologic error frequencies and to improve Papanicolaou test metrics. Laboratory quality assurance practices have been used to track error rates, and laboratories are starting to use these data for error reduction initiatives.

  3. Regulatory Control of Radiation Sources. Safety Guide

    International Nuclear Information System (INIS)

    2009-01-01

    This Safety Guide is intended to assist States in implementing the requirements established in Safety Standards Series No. GS-R-1, Legal and Governmental Infrastructure for Nuclear, Radiation, Radioactive Waste and Transport Safety, for a national regulatory infrastructure to regulate any practice involving radiation sources in medicine, industry, research, agriculture and education. The Safety Guide provides advice on the legislative basis for establishing regulatory bodies, including the effective independence of the regulatory body. It also provides guidance on implementing the functions and activities of regulatory bodies: the development of regulations and guides on radiation safety; implementation of a system for notification and authorization; carrying out regulatory inspections; taking necessary enforcement actions; and investigating accidents and circumstances potentially giving rise to accidents. The various aspects relating to the regulatory control of consumer products are explained, including justification, optimization of exposure, safety assessment and authorization. Guidance is also provided on the organization and staffing of regulatory bodies. Contents: 1. Introduction; 2. Legal framework for a regulatory infrastructure; 3. Principal functions and activities of the regulatory body; 4. Regulatory control of the supply of consumer products; 5. Functions of the regulatory body shared with other governmental agencies; 6. Organization and staffing of the regulatory body; 7. Documentation of the functions and activities of the regulatory body; 8. Support services; 9. Quality management for the regulatory system.

  4. Research on Cooperation Strategy of Enterprises’ Quality and Safety in Food Supply Chain

    Directory of Open Access Journals (Sweden)

    Jining Wang

    2015-01-01

    Full Text Available In order to prevent and control risk factors which harm the quality and safety of the food supply chain effectively and reduce the probability of food safety incidents, this paper investigated on some problems of the upstream and downstream enterprises of the food supply chain under the three different forms of cooperation based on the neoclassic economics and game theory method. These problems include the effectiveness of the quality and safety efforts, the profits, the effect of the losses that the food safety incidents caused on the quality efforts’ efficacy, and the social welfare comparison. Meanwhile, we constructed evolutionary game model to analyze the macro and micro factors that influenced the cooperation strategy and demonstrated the effect of diversity of decision-making parameters on evolution results based on numerical simulation. By the theoretical and simulation analysis, we found that (1 the quality efforts’ efficacy, the profits, the sensitivity coefficient of the quality efforts efficiency to the losses, and the social welfare without thinking about the externality all met their maximum under the full cooperation situation; (2 strengthening supervision over the source of the food supply chain can reduce the probability of food safety incidents; (3 macro and micro environment will be the important basis for companies’ decision-making on cooperation strategy in the food supply chain.

  5. IMPACTS OF SAFETY and QUALITY IN ENVIRONMENTAL RESTORATION AT HANFORD

    International Nuclear Information System (INIS)

    PREVETTE, S.S.

    2004-01-01

    The aim of this paper is to demonstrate the integration of safety methodology, quality tools, leadership, and teamwork at Hanford and their significant positive impact on safe performance of work. Control charts, Pareto Charts, Dr. W. Edward Deming's Red Bead Experiment, and Dr. Deming's System of Profound Knowledge have been the principal tools and theory of an integrated management system. Coupled with involved leadership and teamwork they have led to significant improvements in worker safety and protection, and environmental restoration at one of the nation's largest nuclear cleanup sites

  6. Food quality and safety management

    Directory of Open Access Journals (Sweden)

    Agnieszka Bilska

    2014-09-01

    Full Text Available Ensuring quality and safety of food are nowadays the most important goals set by companies who produce and distribute it. As a result, regulations have been introduced in the European Union countries concerning the production and distribution of food as well as norms which oblige companies to implement and execute several quality management systems.

  7. Quality and Safety Assurance of Iron Casts and Manufacturing Processes

    OpenAIRE

    Kukla S.

    2016-01-01

    The scope of this work focuses on the aspects of quality and safety assurance of the iron cast manufacturing processes. Special attention was given to the processes of quality control and after-machining of iron casts manufactured on automatic foundry lines. Due to low level of automation and huge work intensity at this stage of the process, a model area was established which underwent reorganization in accordance with the assumptions of the World Class Manufacturing (WCM). An analysis of wor...

  8. The History of Infant Formula: Quality, Safety, and Standard Methods.

    Science.gov (United States)

    Wargo, Wayne F

    2016-01-01

    Food-related laws and regulations have existed since ancient times. Egyptian scrolls prescribed the labeling needed for certain foods. In ancient Athens, beer and wines were inspected for purity and soundness, and the Romans had a well-organized state food control system to protect consumers from fraud or bad produce. In Europe during the Middle Ages, individual countries passed laws concerning the quality and safety of eggs, sausages, cheese, beer, wine, and bread; some of these laws still exist today. But more modern dietary guidelines and food regulations have their origins in the latter half of the 19th century when the first general food laws were adopted and basic food control systems were implemented to monitor compliance. Around this time, science and food chemistry began to provide the tools to determine "purity" of food based primarily on chemical composition and to determine whether it had been adulterated in any way. Since the key chemical components of mammalian milk were first understood, infant formulas have steadily advanced in complexity as manufacturers attempt to close the compositional gap with human breast milk. To verify these compositional innovations and ensure product quality and safety, infant formula has become one of the most regulated foods in the world. The present paper examines the historical development of nutritional alternatives to breastfeeding, focusing on efforts undertaken to ensure the quality and safety from antiquity to present day. The impact of commercial infant formulas on global regulations is addressed, along with the resulting need for harmonized, fit-for-purpose, voluntary consensus standard methods.

  9. Building quality into performance and safety assessment software

    International Nuclear Information System (INIS)

    Wojciechowski, L.C.

    2011-01-01

    Quality assurance is integrated throughout the development lifecycle for performance and safety assessment software. The software used in the performance and safety assessment of a Canadian deep geological repository (DGR) follows the CSA quality assurance standard CSA-N286.7 [1], Quality Assurance of Analytical, Scientific and Design Computer Programs for Nuclear Power Plants. Quality assurance activities in this standard include tasks such as verification and inspection; however, much more is involved in producing a quality software computer program. The types of errors found with different verification methods are described. The integrated quality process ensures that defects are found and corrected as early as possible. (author)

  10. Quality management of pharmacology and safety pharmacology studies

    DEFF Research Database (Denmark)

    Spindler, Per; Seiler, Jürg P

    2002-01-01

    to safety pharmacology studies, and, when indicated, to secondary pharmacodynamic studies, does not influence the scientific standards of studies. However, applying formal GLP standards will ensure the quality, reliability and integrity of studies, which reflect sound study management. It is important...... to encourage a positive attitude among researchers and academics towards these lines, whenever possible. GLP principles applied to the management of non-clinical safety studies are appropriate quality standards when studies are used in the context of protecting public health, and these quality standards...... of pharmacology studies (ICH S7A): primary pharmacodynamic, secondary pharmacodynamic and safety pharmacology studies, and guidance on the quality standards (expectations for GLP conformity) for these study types have been provided. Primary pharmacodynamic studies are the only study types that are fully exempt...

  11. Theoretical Application of Supervision over Quality and Safety of Agricultural Products

    Institute of Scientific and Technical Information of China (English)

    Xin; CHENG; Ying; ZHANG

    2013-01-01

    Supervision over quality and safety of agricultural products has received high attention of management department.Competent authorities have formulated and issued many measures to strengthen supervision over quality and safety of agricultural products and improve China’s agricultural product quality and safety level.From the perspective of management science,this paper elaborates basic contents of two basic management theories,Broken Windows Effect and Effect of Heat Furnace.Then,it analyzes influence of Broken Windows Effect and Effect of Heat Furnace on supervision over quality and safety of agricultural products.Finally,it comes up with recommendations for supervision over quality and safety of agricultural products.

  12. Safety control and risk management

    International Nuclear Information System (INIS)

    Rasmussen, J.

    1987-01-01

    The acceptable probability of major accidents in nuclear power is very small, and can not be determined from direct empirical evidence. Therefore, control of the level of safety is a complex problem. The difficulty is related to the fact that a variable, 'safety', which is not accessible to direct measurement, is to be tightly controlled. Control, therefore, depends on a systematic, analytical prediction of the target state, i.e., the level of safety, from indirect evidence. From a control theoretic point of view this means that safety is controlled by a system which includes openloop as well as closed loop control paths. The aim of the paper is to take a general systems view on the complex mechanisms involved in the control of safety of industrial installations like nuclear power. From this, the role of probabilistic risk analysis is evaluated and needs for further development discussed. (author)

  13. A study on enforcement effects of radiation safety control regulations for diagnostic X-ray equipment

    International Nuclear Information System (INIS)

    Sung, Mo IL; Park, Myeong Hwan; Kwon, Duk Moon; Lee, Joon IL

    1999-01-01

    The purposes of this study are to analyze the realities after enforcements of safety control regulations for diagnostic X-ray equipment and to suggest means for an improvement of low radiation safety control. A questionnaire survey for medical radiologic technologists was carried out to determine enforcement effects of the safety control regulations. The results of analysis from the survey are as follows. That is, most of he respondents realized the importance of the radiation safety control system, but about a half of them revealed that regulations were not well observed in accordance with their purposes. Only 43.9 percent of the respondents took an active part in quality control of radiation. And responsibility, sex, age, and knowledge for safety control were important indicators for observations of the regulations. Training for the safety control regulations are needed to ensure safety control and proper usage of diagnostic X-ray equipment. And management of organizations using diagnostic X-ray equipment have to understand and stress the importance of radiation safety control system. (author)

  14. Innovation of Supervision System for Quality and Safety of Edible Agricultural Products

    Institute of Scientific and Technical Information of China (English)

    Xingxing; MEI; Zhongchao; FENG

    2014-01-01

    This paper elaborated multidimensional characteristics of quality and safety of agricultural products,introduced current situation of quality and safety supervision of edible agricultural products in China,analyzed existing problems of quality and safety supervision system and corresponding reasons,and finally came up with recommendations for innovation of supervision system for quality and safety of agricultural products.

  15. Quality assurance/quality control, reliability and availability of nuclear power plants

    International Nuclear Information System (INIS)

    Kueffer, K.

    1981-01-01

    In a first part this lectures will present a survey on nuclear power production and plant performance in the Western World and discuss key parameters such as load factors and non-availability. Some main reasons for reliable performance of nuclear power plants are given. The second part of this lecture deals with the question how quality assurance and quality control measures do directly influence plant reliability, availability and, thus, economy. Derived from worldwide experience gained from operating nuclear power plants, it may be concluded that the implementation of an overall quality assurance programme does not only satisfy safety requirements set forth by the nuclear regulatory bodies, but has also a considerable impact on plant reliability and availability. A positive effect on these figures will be achieved if the established quality assurance programme provides for a coordinated approach to all activities affecting quality. It is discussed how the quality of a product should be controlled and what kind of quality assurance measures by performed examples are given to demonstrate that the expenditure for maintenance work on components will decrease if planned and systematic quality assurance actions have been implemented during all procurement stages. (orig./RW)

  16. FOOD SAFETY CONTROL SYSTEM IN CHINA

    Institute of Scientific and Technical Information of China (English)

    Liu Wei-jun; Wei Yi-min; Han Jun; Luo Dan; Pan Jia-rong

    2007-01-01

    Most countries have expended much effort to develop food safety control systems to ensure safe food supplies within their borders. China, as one of the world's largest food producers and consumers,pays a lot of attention to food safety issues. In recent years, China has taken actions and implemented a series of plans in respect to food safety. Food safety control systems including regulatory, supervisory,and science and technology systems, have begun to be established in China. Using, as a base, an analysis of the current Chinese food safety control system as measured against international standards, this paper discusses the need for China to standardize its food safety control system. We then suggest some policies and measures to improve the Chinese food safety control system.

  17. Physical aspects of quality assurance in nuclear medicine and radiotherapy, regulatory approach of the National Nuclear Safety Center

    International Nuclear Information System (INIS)

    Gonzalez C, D.; Fuente P, A. de la; Quevedo G, J.R.; Lopez F, Y.; Varela C, C.

    2006-01-01

    The physical aspects of the quality guarantee in Nuclear Medicine and Radiotherapy its are of cardinal importance to guarantee the quality of the diagnoses and treatments that are carried out to the patients in this type of services. The OIEA, the OMS and other scientific and professional organizations have contributed significantly to the elaboration of recommendations, Protocols, etc. applicable in the quality control programs and safety of the Nuclear Medicine and Radiotherapy departments. In spite of the great effort developed in this sense the Installation of the programs of quality control and safety of the Nuclear Medicine and Radiotherapy departments can fail if the same ones are not based in three decisive elements that are: the existence of national regulations, the existence of the infrastructure required for it and the existence of enough qualified personnel to develop this programs. The present work shows the regulatory focus that on this topic, it has followed the National Center of Nuclear Safety of Cuba (CNSN). The same left of strengthen all the existent Synergies in the different organizations of the country and it went in two fundamental directions: installation of the regulatory requirements that govern this activity and the Authorization of a Cuban Entity, specialized in carrying out audits to the quality control and safety programs of the Nuclear Medicine and Radiotherapy departments. After 4 work years in this direction, the results confirm the validity of the experience developed by the CNSN, at the moment all the services of Nuclear Medicine and Radiotherapy of Cuba possess quality control and safety programs, these programs are annually Auditing by an Authorized entity by the CNSN and the Inspectors of the Regulatory Authority, control, during the inspections, the one execution of the established requirements in the national regulations. The work developed so far can serve, modestly, of reference to others countries of Latin America that

  18. Compositional Synthesis of Safety Controllers

    NARCIS (Netherlands)

    Kuijper, W.

    2012-01-01

    In my thesis I investigate compositional techniques for synthesis of safety controllers. A safety controller, in this context, is a state machine that gives the set of safe control outputs for every possible sequence of observations from the plant under control. Compositionality, in this context,

  19. NIF Projects Controls and Information Systems Software Quality Assurance Plan

    Energy Technology Data Exchange (ETDEWEB)

    Fishler, B

    2011-03-18

    Quality achievement for the National Ignition Facility (NIF) and the National Ignition Campaign (NIC) is the responsibility of the NIF Projects line organization as described in the NIF and Photon Science Directorate Quality Assurance Plan (NIF QA Plan). This Software Quality Assurance Plan (SQAP) is subordinate to the NIF QA Plan and establishes quality assurance (QA) activities for the software subsystems within Controls and Information Systems (CIS). This SQAP implements an activity level software quality assurance plan for NIF Projects as required by the LLNL Institutional Software Quality Assurance Program (ISQAP). Planned QA activities help achieve, assess, and maintain appropriate quality of software developed and/or acquired for control systems, shot data systems, laser performance modeling systems, business applications, industrial control and safety systems, and information technology systems. The objective of this SQAP is to ensure that appropriate controls are developed and implemented for management planning, work execution, and quality assessment of the CIS organization's software activities. The CIS line organization places special QA emphasis on rigorous configuration control, change management, testing, and issue tracking to help achieve its quality goals.

  20. NIF Projects Controls and Information Systems Software Quality Assurance Plan

    International Nuclear Information System (INIS)

    Fishler, B.

    2011-01-01

    Quality achievement for the National Ignition Facility (NIF) and the National Ignition Campaign (NIC) is the responsibility of the NIF Projects line organization as described in the NIF and Photon Science Directorate Quality Assurance Plan (NIF QA Plan). This Software Quality Assurance Plan (SQAP) is subordinate to the NIF QA Plan and establishes quality assurance (QA) activities for the software subsystems within Controls and Information Systems (CIS). This SQAP implements an activity level software quality assurance plan for NIF Projects as required by the LLNL Institutional Software Quality Assurance Program (ISQAP). Planned QA activities help achieve, assess, and maintain appropriate quality of software developed and/or acquired for control systems, shot data systems, laser performance modeling systems, business applications, industrial control and safety systems, and information technology systems. The objective of this SQAP is to ensure that appropriate controls are developed and implemented for management planning, work execution, and quality assessment of the CIS organization's software activities. The CIS line organization places special QA emphasis on rigorous configuration control, change management, testing, and issue tracking to help achieve its quality goals.

  1. Consumer Choice between Food Safety and Food Quality: The Case of Farm-Raised Atlantic Salmon

    Science.gov (United States)

    Haghiri, Morteza

    2016-01-01

    Since the food incidence of polychlorinated biphenyls in farm-raised Atlantic salmon, its market demand has drastically changed as a result of consumers mistrust in both the quality and safety of the product. Policymakers have been trying to find ways to ensure consumers that farm-raised Atlantic salmon is safe. One of the suggested policies is the implementation of integrated traceability methods and quality control systems. This article examines consumer choice between food safety and food quality to purchase certified farm-raised Atlantic salmon, defined as a product that has passed through various stages of traceability systems in the province of Newfoundland and Labrador, Canada. PMID:28231118

  2. Factors impacting on the microbiological quality and safety of ...

    African Journals Online (AJOL)

    Problems with the safety and shelf life of export hake have been raised by the Namibian fishing industry. This prompted an investigation into the factors that may have an impact on the microbiological quality and safety of processed hake. Samples were collected along the processing line; the general microbiological quality ...

  3. Implementation of an Enhanced Measurement Control Program for handling nuclear safety samples at WSRC

    International Nuclear Information System (INIS)

    Boler-Melton, C.; Holland, M.K.

    1991-01-01

    In the separation and purification of nuclear material, nuclear criticality safety (NCS) is of primary concern. The primary nuclear criticality safety controls utilized by the Savannah River Site (SRS) Separations Facilities involve administrative and process equipment controls. Additional assurance of NCS is obtained by identifying key process hold points where sampling is used to independently verify the effectiveness of production control. Nuclear safety measurements of samples from these key process locations provide a high degree of assurance that processing conditions are within administrative and procedural nuclear safety controls. An enhanced procedure management system aimed at making improvements in the quality, safety, and conduct of operation was implemented for Nuclear Safety Sample (NSS) receipt, analysis, and reporting. All procedures with nuclear safety implications were reviewed for accuracy and adequate detail to perform the analytical measurements safely, efficiently, and with the utmost quality. Laboratory personnel worked in a ''Deliberate Operating'' mode (a systematic process requiring continuous expert oversight during all phases of training, testing, and implementation) to initiate the upgrades. Thus, the effort to revise and review nuclear safety sample procedures involved a team comprised of a supervisor, chemist, and two technicians for each procedure. Each NSS procedure was upgraded to a ''Use Every Time'' (UET) procedure with sign-off steps to ensure compliance with each step for every nuclear safety sample analyzed. The upgrade program met and exceeded both the long and short term customer needs by improving measurement reliability, providing objective evidence of rigid adherence to program principles and requirements, and enhancing the system for independent verification of representative sampling from designated NCS points

  4. European demands for food quality and safety

    OpenAIRE

    Bulatsyk, Sofiya; Yavorska, Nadiya

    2017-01-01

    In this article was investigated regulations and other normative documents of the European Union concerning food quality and safety and was arranged EU demands regards to food safety. There were determined the basic business concerns of the domestic enterprises in the process of manufacturing and marketing food products

  5. Quality management, a directive approach to patient safety.

    Science.gov (United States)

    Ayuso-Murillo, Diego; de Andrés-Gimeno, Begoña; Noriega-Matanza, Concha; López-Suárez, Rafael Jesús; Herrera-Peco, Ivan

    Nowadays the implementation of effective quality management systems and external evaluation in healthcare is a necessity to ensure not only transparency in activities related to health but also access to health and patient safety. The key to correctly implementing a quality management system is support from the managers of health facilities, since it is managers who design and communicate to health professionals the strategies of action involved in quality management systems. This article focuses on nursing managers' approach to quality management through the implementation of cycles of continuous improvement, participation of improvement groups, monitoring systems and external evaluation quality models (EFQM, ISO). The implementation of a quality management system will enable preventable adverse effects to be minimized or eliminated, and promote patient safety and safe practice by health professionals. Copyright © 2017 Elsevier España, S.L.U. All rights reserved.

  6. Quality control of the packet of RELAP5/MOD2 code

    International Nuclear Information System (INIS)

    Pomier Baez, L.E.

    1993-01-01

    The methodology that should be used to perform the quality control of entrance data set of RELAP5 calculation code is expounded in this work with this control method an extreme reliability is quarantined in the calculation model established to perform the safety thermohydraulic analysis with the help of RELAP5. This makes possible the complex simulation studies of a nuclear power plant with the quality required

  7. Ensuring the quality of occupational safety risk assessment.

    Science.gov (United States)

    Pinto, Abel; Ribeiro, Rita A; Nunes, Isabel L

    2013-03-01

    In work environments, the main aim of occupational safety risk assessment (OSRA) is to improve the safety level of an installation or site by either preventing accidents and injuries or minimizing their consequences. To this end, it is of paramount importance to identify all sources of hazards and assess their potential to cause problems in the respective context. If the OSRA process is inadequate and/or not applied effectively, it results in an ineffective safety prevention program and inefficient use of resources. An appropriate OSRA is an essential component of the occupational safety risk management process in industries. In this article, we performed a survey to elicit the relative importance for identified OSRA tasks to enable an in-depth evaluation of the quality of risk assessments related to occupational safety aspects on industrial sites. The survey involved defining a questionnaire with the most important elements (tasks) for OSRA quality assessment, which was then presented to safety experts in the mining, electrical power production, transportation, and petrochemical industries. With this work, we expect to contribute to the main question of OSRA in industries: "What constitutes a good occupational safety risk assessment?" The results obtained from the questionnaire showed that experts agree with the proposed OSRA process decomposition in steps and tasks (taxonomy) and also with the importance of assigning weights to obtain knowledge about OSRA task relevance. The knowledge gained will enable us, in the near future, to build a framework to evaluate OSRA quality for industrial sites. © 2012 Society for Risk Analysis.

  8. Regulatory Control of Radiation Sources. Safety Guide (Arabic Edition)

    International Nuclear Information System (INIS)

    2012-01-01

    This Safety Guide is intended to assist States in implementing the requirements established in Safety Standards Series No. GS-R-1, Legal and Governmental Infrastructure for Nuclear, Radiation, Radioactive Waste and Transport Safety, for a national regulatory infrastructure to regulate any practice involving radiation sources in medicine, industry, research, agriculture and education. The Safety Guide provides advice on the legislative basis for establishing regulatory bodies, including the effective independence of the regulatory body. It also provides guidance on implementing the functions and activities of regulatory bodies: the development of regulations and guides on radiation safety; implementation of a system for notification and authorization; carrying out regulatory inspections; taking necessary enforcement actions; and investigating accidents and circumstances potentially giving rise to accidents. The various aspects relating to the regulatory control of consumer products are explained, including justification, optimization of exposure, safety assessment and authorization. Guidance is also provided on the organization and staffing of regulatory bodies. Contents: 1. Introduction; 2. Legal framework for a regulatory infrastructure; 3. Principal functions and activities of the regulatory body; 4. Regulatory control of the supply of consumer products; 5. Functions of the regulatory body shared with other governmental agencies; 6. Organization and staffing of the regulatory body; 7. Documentation of the functions and activities of the regulatory body; 8. Support services; 9. Quality management for the regulatory system.

  9. Quality assurance: image production and film quality

    International Nuclear Information System (INIS)

    Abd Aziz Mhd Ramli

    2004-01-01

    The contents of this chapter are follows - Factors Affecting Image Quality and Patient Dose: Quality Control in Diagnostic Radiology, Mechanical Safety, Electrical Safety, Radiation Protection, Performance and Safety Standard, Calibration of QC Test Tools

  10. Quality control in diagnostic radiology: experience and challenges

    International Nuclear Information System (INIS)

    Abd Aziz Mhd Ramli; Mohd Ramli Arshad; Mohd Khalid Matori; Muhammad Jamal Md Isa; Husaini Salleh; Abdullah Tahir Aliyasak; Zainal Jamaluddin; Hasrul Hisham Hussain

    2005-01-01

    Malaysian Institute for Nuclear Technology Research through its Medical Physics Group has been providing Quality Control (QC) services for medical x-ray apparatus used in diagnostic radiology to private clinics and hospitals since the year 1997. The quality control (QC) in diagnostic radiology is considered as part of quality assurance program which provide accurate diagnostic information at the lowest cost and the least exposure of the patients to radiation. Many experience and obstacles were faced by Medical Physics Group. This paper will discuss on some of the experiences and challenges that could be shared together with MINT staff especially in the safety aspect related to electrical and mechanical, radiation protection, performance and standard. The challenging in administrative aspect also will discuss. (Author)

  11. Quality management and perceptions of teamwork and safety climate in European hospitals.

    Science.gov (United States)

    Kristensen, Solvejg; Hammer, Antje; Bartels, Paul; Suñol, Rosa; Groene, Oliver; Thompson, Caroline A; Arah, Onyebuchi A; Kutaj-Wasikowska, Halina; Michel, Philippe; Wagner, Cordula

    2015-12-01

    This study aimed to investigate the associations of quality management systems with teamwork and safety climate, and to describe and compare differences in perceptions of teamwork climate and safety climate among clinical leaders and frontline clinicians. We used a multi-method, cross-sectional approach to collect survey data of quality management systems and perceived teamwork and safety climate. Our data analyses included descriptive and multilevel regression methods. Data on implementation of quality management system from seven European countries were evaluated including patient safety culture surveys from 3622 clinical leaders and 4903 frontline clinicians. Perceived teamwork and safety climate. Teamwork climate was reported as positive by 67% of clinical leaders and 43% of frontline clinicians. Safety climate was perceived as positive by 54% of clinical leaders and 32% of frontline clinicians. We found positive associations between implementation of quality management systems and teamwork and safety climate. Our findings, which should be placed in a broader clinical quality improvement context, point to the importance of quality management systems as a supportive structural feature for promoting teamwork and safety climate. To gain a deeper understanding of this association, further qualitative and quantitative studies using longitudinally collected data are recommended. The study also confirms that more clinical leaders than frontline clinicians have a positive perception of teamwork and safety climate. Such differences should be accounted for in daily clinical practice and when tailoring initiatives to improve teamwork and safety climate. © The Author 2015. Published by Oxford University Press in association with the International Society for Quality in Health Care; all rights reserved.

  12. Recent developments in intelligent packaging for enhancing food quality and safety.

    Science.gov (United States)

    Sohail, Muhammad; Sun, Da-Wen; Zhu, Zhiwei

    2018-03-07

    The role of packaging cannot be denied in the life cycle of any food product. Intelligent packaging is an emerging technology in the food packaging sector. Although it still needs its full emergence in the market, its importance has been proved for the maintenance of food quality and safety. The present review describes several aspects of intelligent packaging. It first highlights different tools used in intelligent packaging and elucidates the role of these packaging devices for maintaining the quality of different food items in terms of controlling microbial growth and gas concentration, and for providing convenience and easiness to its users in the form of time temperature indication. This review also discusses other intelligent packaging solutions in supply chain management of food products to control theft and counterfeiting conducts and broaden the image of the food companies in terms of branding and marketing. Overall, intelligent packaging can ensure food quality and safety in the food industry, however there are still some concerns over this emerging technology including high cost and legal aspects, and thus future work should be performed to overcome these problems for further promoting its applications in the food industry. Moreover, work should also be carried out to combine several single intelligent packaging devices into a single one, so that most of the benefits from this emerging technology can be achieved.

  13. The future trends for research on quality and safety of animal products

    Directory of Open Access Journals (Sweden)

    Nigel D. Scollan

    2010-01-01

    Full Text Available Quality must now be considered as a convergence between consumers' wishes and needs and the intrinsic and extrinsic quality attributes of food products. The increasing number of quality attributes which must be considered, increasing globalisation and the heterogeneity in consumption habits between countries are making this convergence progressively more difficult. In parallel, science is rapidly evolving (with the advent of genomics for instance, and a growing number of applications is thus expected for the improvement of food safety and quality. Among the meat and fish quality attributes, colour is very important because it determines, at least in part, consumer choice. The key targets to ensure a satisfactory colour are animal nutrition and management for fish, processing and product conditioning for meat. Tenderness and flavour continue to be important issues for the consumer because eating remains a pleasure. They both determine quality experience which itself influences repetitive purchase. Meat tenderness is a very complex problem which can be solved only by a holistic approach involving all the factors from conception, animal breeding and production, muscle biology and slaughter practice to carcass processing and meat preparation at the consumer end. Today, safety and healthiness are among the most important issues. Unfortunately, animal products can potentially be a source of biological and chemical contamination for consumers. The introduction of both control strategies along the food chain and the development of a food safety management system, from primary production to the domestic environment, are key issues that must be achieved. Despite a high dietary supply of saturated fats by dairy and meat products, it is imperative that professionals involved in animal research and in the associated industry convey the positive nutritional contributions of animal products to both consumers and health professionals. The latter include protein

  14. Visualising differences in professionals' perspectives on quality and safety.

    Science.gov (United States)

    Travaglia, Joanne Francis; Nugus, Peter Ivan; Greenfield, David; Westbrook, Johanna Irene; Braithwaite, Jeffrey

    2012-09-01

    The safety-and-quality movement is now two decades old. Errors persist despite best efforts, indicating that there are entrenched overt and perhaps less explicit barriers limiting the success of improvement efforts. OBJECTIVES AND HYPOTHESES: To examine the perspectives of five groups of healthcare workers (administrative staff, nurses, medical practitioners, allied health and managers) and to compare and contrast their descriptions of quality-and-safety activities within their organisation. Differences in perspectives can be an indicator of divergence in the conceptualisation of, and impetus for, quality-improvement strategies which are intended to engage healthcare professions and staff. Study data were collected in a defined geographical healthcare jurisdiction in Australia, via individual and group interviews held across four service streams (aged care and rehabilitation; mental health; community health; and cancer services). Data were collected in 2008 and analysed, using data-mining software, in 2009. Clear differences in the perspectives of professional groups were evident, suggesting variations in the perceptions of, and priorities for, quality and safety. The visual representation of quality and safety perspectives provides insights into the conceptual maps currently utilised by healthcare workers. Understanding the similarity and differences in these maps may enable more effective targeting of interprofessional improvement strategies.

  15. Prevention and control of food safety risks: the role of governments, food producers, marketers, and academia.

    Science.gov (United States)

    Lupien, John R

    2007-01-01

    Food systems are rapidly changing as world population grows, increasing urbanization occurs, consumer tastes and preferences change and differ in various countries and cultures, large scale food production increases, and food imports and exports grow in volume and value. Consumers in all countries have become more insistent that foods available in the marketplace are of good quality and safe, and do not pose risks to them and their families. Publicity about food risk problems and related risks, including chemical and microbiological contamination of foods, mad-cow disease, avian flu, industrial chemical contamination all have made consumers and policy makers more aware of the need of the control of food safety risk factors in all countries. To discuss changes in food systems, and in consumer expectations, that have placed additional stress on the need for better control of food safety risks. Food producers, processors, and marketers have additional food law and regulations to meet; government agencies must increase monitoring and enforcement of adequate food quality and safety legislation and coordinate efforts between agriculture, health, trade, justice and customs agencies; and academia must take action to strengthen the education of competent food legislation administrators, inspectorate, and laboratory personnel for work in government and industry, including related food and food safety research . Both Government and the food industry must assure that adequate control programs are in place to control the quality and safety of all foods, raw or processed, throughout the food chain from production to final consumption. This includes appropriate laboratory facilities to perform necessary analysis of foods for risk and quality factors, and to carry out a wide range of food science, toxicological and related research.

  16. Total Quality Management and the System Safety Secretary

    Science.gov (United States)

    Elliott, Suzan E.

    1993-01-01

    The system safety secretary is a valuable member of the system safety team. As downsizing occurs to meet economic constraints, the Total Quality Management (TQM) approach is frequently adopted as a formula for success and, in some cases, for survival.

  17. Quality control aspects of herbs and botanicals in developing countries: Coleus forskohlii Briq a case study

    Directory of Open Access Journals (Sweden)

    Ennus Tajuddin Tamboli

    2015-01-01

    Full Text Available Objective: Current trend of commercialization of herbal medicines draw a huge need of maintaining their quality. The declaration of quality, safety and efficacy of medicinal plants as well as poly-herbal formulations has become an important issue. Hence, qualitative and quantitative analysis of herbal drugs and formulations viz., fingerprint profiles and quantification of the various markers become key factors of quality control. Materials and Methods: Present investigation is a detailed report for quality control of well-known herb Coleus forskohlii Briq, which includes physicochemical parameter determination, safety evaluation, microscropical evaluation, and chromatographic fingerprinting as well. Results: Physico-chemical characters were evaluated according to Indian Pharmacopoeia, further microscopic evaluation of transverse section of Coleus reveals that periderm, secondary phloem, and wide secondary xylem cylinder, which occupies major portion of the root fragmentary. Chromatographic fingerprint profiles of Coleus have been generated, and a marker based standardization strategy was adopted; using different analytical technique like high-performance thin layer chromatography, high-performance liquid chromatography and gas chromatography-mass spectroscopy to maintain quality and ensure safety as well as efficacy. Conclusion: These advancements in modern techniques of analysis can lead to effective quality control of Coleus as well as other herbs. Present report can act as pioneer for quality control of modern herbal medicine.

  18. Microbiological quality and safety assessment of lettuce production in Brazil.

    Science.gov (United States)

    Ceuppens, Siele; Hessel, Claudia Titze; de Quadros Rodrigues, Rochele; Bartz, Sabrina; Tondo, Eduardo César; Uyttendaele, Mieke

    2014-07-02

    The microbiological quality and safety of lettuce during primary production in Brazil were determined by enumeration of hygiene indicators Escherichia coli, coliforms and enterococci and detection of enteric pathogens Salmonella and E. coli O157:H7 in organic fertilizers, soil, irrigation water, lettuce crops, harvest boxes and worker's hands taken from six different lettuce farms throughout the crop growth cycle. Generic E. coli was a suitable indicator for the presence of Salmonella and E. coli O157:H7, while coliforms and enterococci were not. Few pathogens were detected: 5 salmonellae and 2 E. coli O157:H7 from 260 samples, of which only one was lettuce and the others were manure, soil and water. Most (5/7) pathogens were isolated from the same farm and all were from organic production. Statistical analysis revealed the following environmental and agro-technical risk factors for increased microbial load and pathogen prevalence in lettuce production: high temperature, flooding of lettuce fields, application of contaminated organic fertilizer, irrigation with water of inferior quality and large distances between the field and toilets. Control of the composting process of organic fertilizers and the irrigation water quality appear most crucial to improve and/or maintain the microbiological quality and safety during the primary production of lettuce. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Production process and quality control for the HTTR fuel

    International Nuclear Information System (INIS)

    Yoshimuta, S.; Suzuki, N.; Kaneko, M.; Fukuda, K.

    1991-01-01

    Development of the production and inspection technology for High Temperature Engineering Test Reactor (HTTR) fuel has been carried out by cooperative work between Japan Atomic Energy Research Institute (JAERI) and Nuclear Fuel Industries, Ltd (NFI). The performance and the quality level of the developed fuel are well established to meet the design requirements of the HTTR. For the commercial scale production of the fuel, statistical quality control and quality assurance must be carefully considered in order to assure the safety of the HTTR. It is also important to produce the fuel under well controlled process condition. To meet these requirements in the production of the HTTR fuel, a new production process and quality control system is to be introduced in the new facilities. The main feature of the system is a computer integrated control system. Process control data at each production stage of products and semi-products are all gathered by terminal computers and processed by a host computer. The processed information is effectively used for the production, quality and accountancy control. With the aid of this system, all the products will be easily traceable from starting materials to final stages and the statistical evaluation of the quality of products becomes more reliable. (author). 8 figs

  20. Quality assurance and radiation safety in positron emission tomography

    International Nuclear Information System (INIS)

    Kmetyuk, Ya.V.; Radosh, H.V.; Bezshyyko, O.A.; Golinka-Bezshyyko, L.O.; Kadenko, I.M.; Kazinova, O.A.; Nagai, A.O.

    2012-01-01

    Scientific studies, clinical experience and economic analysis have shown that the positron emission tomography (PET) is clinically and cost effective cancer diagnostics method. Combined PET and computed tomography (PET/CT) has proven clinical utility, particularly in the diagnosis, staging or restaging malignant disease and metastases, surgical planning, radiation therapy planning and evaluation of treatment response. The use of PET/CT has grown substantially in the past few years, with an increasing number of hospitals and installations of PET/CT imaging centers each year. In the same time combination of 2 procedures, each of which impart a radiation dose and, as a result, increases the deleterious influence for health, creates additional radiation safety issues. In these conditions the role of quality assurance (QA) and quality control (QC) programs is getting more and more important. We considered main QA and radiation safety requirements for whole PET technology chain from radio-pharmacy facilities to PET/CT scanning and patient release criteria. All these issues were considered and assessed having the example of PET facilities and technology chain of All-Ukrainian Center for Radiosurgery of the Clinical Hospital 'Feofania'

  1. Safety culture as a matter of regulatory control and regulatory effectiveness

    International Nuclear Information System (INIS)

    Camargo, C.T.M.; Furieri, E.B.; Arrieta, L.A.I.; Almeida, C.U.C.

    2002-01-01

    More than 15 years have passed since the term 'safety culture' was introduced by the International Nuclear Safety Advisory Group (INSAG), and although the concept now is widely accepted, practical applications and characteristics have been disseminated mainly for nuclear power plant operating organizations. There is still a lack of international guidance on the use of safety culture as a regulatory matter and on the application of the concept within regulatory organizations. This work explores the meaning of safety culture in two different fields: as an element of safety management systems it shall be a matter of regulatory control; as a complementary tool for quality management it should be used to enhance regulatory effectiveness. Brazilian recent experience on regulating nuclear power reactors provide some examples on how the concept of safety culture may influence regulatory strategies and regulatory management. (author)

  2. A kaizen approach to food safety quality management in the value chain from wheat to bread

    CERN Document Server

    Hill, Victoria

    2014-01-01

    This book provides a Management Science approach to quality management in food production. Aspects of food quality, product conformance and reliability/food safety are examined, starting with wheat and ending with its value chain transformation into bread. Protein qualities that influence glycemic index levels in bread are used to compare the value chains of France and the US. With Kaizen models the book shows how changes in these characteristics are the result of management decisions made by the wheat growers in response to government policy and industry strategy. Lastly, it provides step-by-step instructions on how to apply kaizen methodology and Deming's work on quality improvement to make the HACCPs (Hazard Analysis and Critical Control Points) in food safety systems more robust.

  3. Nuclear safety: a large scale quality audit of pressurized equipment

    International Nuclear Information System (INIS)

    Faudon, Valerie

    2016-01-01

    This article notably refers to, quotes and comments a hearing organised by the French Public Office for the Assessment Scientific and Technological Choices (OPECST) on the issue of safety of pressurized equipment in nuclear reactors, and which gathered the main concerned actors (Areva, EDF, IRSN, ASN) to have an overview of quality controls in AREVA NP fabrication plants. Two different issues have been addressed: a technical metallurgical issue related to some boiler-making parts, and an issue related to quality assurance. These issues concern different older reactors (Fessenheim for example) as well as new ones (EPR Flamanville). The article indicates the different measures planned, envisaged or already implemented by the concerned actors in order to improve knowledge in the boiler-making industry, and to ensure a better quality

  4. quality and safety characteristics of cassava crisps sold in urban

    African Journals Online (AJOL)

    ACSS

    QUALITY AND SAFETY CHARACTERISTICS OF CASSAVA CRISPS SOLD IN. URBAN KENYA. G.O. ABONG', S.I. SHIBAIRO, ... This study sought to characterise the quality and safety in terms of cyanide levels of cassava crisps ... Crantz) to food security and incomes for rural communities in sub-Saharan Africa, cannot be.

  5. TU-EF-BRD-01: Topics in Quality and Safety Research and Level of Evidence

    Energy Technology Data Exchange (ETDEWEB)

    Pawlicki, T. [UCSD Medical Center (United States)

    2015-06-15

    Research related to quality and safety has been a staple of medical physics academic activities for a long time. From very early on, medical physicists have developed new radiation measurement equipment and analysis techniques, created ever increasingly accurate dose calculation models, and have vastly improved imaging, planning, and delivery techniques. These and other areas of interest have improved the quality and safety of radiotherapy for our patients. With the advent of TG-100, quality and safety is an area that will garner even more research interest in the future. As medical physicists pursue quality and safety research in greater numbers, it is worthwhile to consider what actually constitutes research on quality and safety. For example, should the development of algorithms for real-time EPID-based in-vivo dosimetry be defined as “quality and safety” research? How about the clinical implementation of such as system? Surely the application of failure modes and effects analysis to a clinical process would be considered quality and safety research, but is this type of research that should be included in the medical physics peer-reviewed literature? The answers to such questions are of critical importance to set researchers in a direction that will provide the greatest benefit to our field and the patients we serve. The purpose of this symposium is to consider what constitutes research in the arena of quality and safety and differentiate it from other research directions. The key distinction here is developing the tool itself (e.g. algorithms for EPID dosimetry) vs. studying the impact of the tool with some quantitative metric. Only the latter would I call quality and safety research. Issues of ‘basic’ versus ‘applied’ quality and safety research will be covered as well as how the research results should be structured to provide increasing levels of support that a quality and safety intervention is effective and sustainable. Examples from existing

  6. TU-EF-BRD-04: Summing It Up: The Future of Quality and Safety Research

    Energy Technology Data Exchange (ETDEWEB)

    Ford, E. [University of Washington (United States)

    2015-06-15

    Research related to quality and safety has been a staple of medical physics academic activities for a long time. From very early on, medical physicists have developed new radiation measurement equipment and analysis techniques, created ever increasingly accurate dose calculation models, and have vastly improved imaging, planning, and delivery techniques. These and other areas of interest have improved the quality and safety of radiotherapy for our patients. With the advent of TG-100, quality and safety is an area that will garner even more research interest in the future. As medical physicists pursue quality and safety research in greater numbers, it is worthwhile to consider what actually constitutes research on quality and safety. For example, should the development of algorithms for real-time EPID-based in-vivo dosimetry be defined as “quality and safety” research? How about the clinical implementation of such as system? Surely the application of failure modes and effects analysis to a clinical process would be considered quality and safety research, but is this type of research that should be included in the medical physics peer-reviewed literature? The answers to such questions are of critical importance to set researchers in a direction that will provide the greatest benefit to our field and the patients we serve. The purpose of this symposium is to consider what constitutes research in the arena of quality and safety and differentiate it from other research directions. The key distinction here is developing the tool itself (e.g. algorithms for EPID dosimetry) vs. studying the impact of the tool with some quantitative metric. Only the latter would I call quality and safety research. Issues of ‘basic’ versus ‘applied’ quality and safety research will be covered as well as how the research results should be structured to provide increasing levels of support that a quality and safety intervention is effective and sustainable. Examples from existing

  7. TU-EF-BRD-04: Summing It Up: The Future of Quality and Safety Research

    International Nuclear Information System (INIS)

    Ford, E.

    2015-01-01

    Research related to quality and safety has been a staple of medical physics academic activities for a long time. From very early on, medical physicists have developed new radiation measurement equipment and analysis techniques, created ever increasingly accurate dose calculation models, and have vastly improved imaging, planning, and delivery techniques. These and other areas of interest have improved the quality and safety of radiotherapy for our patients. With the advent of TG-100, quality and safety is an area that will garner even more research interest in the future. As medical physicists pursue quality and safety research in greater numbers, it is worthwhile to consider what actually constitutes research on quality and safety. For example, should the development of algorithms for real-time EPID-based in-vivo dosimetry be defined as “quality and safety” research? How about the clinical implementation of such as system? Surely the application of failure modes and effects analysis to a clinical process would be considered quality and safety research, but is this type of research that should be included in the medical physics peer-reviewed literature? The answers to such questions are of critical importance to set researchers in a direction that will provide the greatest benefit to our field and the patients we serve. The purpose of this symposium is to consider what constitutes research in the arena of quality and safety and differentiate it from other research directions. The key distinction here is developing the tool itself (e.g. algorithms for EPID dosimetry) vs. studying the impact of the tool with some quantitative metric. Only the latter would I call quality and safety research. Issues of ‘basic’ versus ‘applied’ quality and safety research will be covered as well as how the research results should be structured to provide increasing levels of support that a quality and safety intervention is effective and sustainable. Examples from existing

  8. Safety control and minimization of radioactive wastes

    International Nuclear Information System (INIS)

    Wang Jinming; Rong Feng; Li Jinyan; Wang Xin

    2010-01-01

    Compared with the developed countries, the safety control and minimization of the radwastes in China are under-developed. The research of measures for the safety control and minimization of the radwastes is very important for the safety control of the radwastes, and the reduction of the treatment and disposal cost and environment radiation hazards. This paper has systematically discussed the safety control and the minimization of the radwastes produced in the nuclear fuel circulation, nuclear technology applications and the process of decommission of nuclear facilities, and has provided some measures and methods for the safety control and minimization of the radwastes. (authors)

  9. Quality and safety is the integral part of our business

    International Nuclear Information System (INIS)

    Fadeev, Y.

    2011-01-01

    During 65 years from Joint-stock Company Afrikantov OKBM foundation over 400 reactor projects were developed - primarily, various modifications of marine propulsion reactors for nuclear submarines and icebreakers of several generations. Today, OKBM designs reactors of various types and purposes as well as equipment, control and protection mechanisms, and is the world leader in fast-neutron sodium-cooled reactor technology. Much attention in OKBM is given to the safety and quality of production, specialists education [ru

  10. Quality and safety training in primary care: making an impact.

    Science.gov (United States)

    Byrne, John M; Hall, Susan; Baz, Sam; Kessler, Todd; Roman, Maher; Patuszynski, Mark; Thakkar, Kruti; Kashner, T Michael

    2012-12-01

    Preparing residents for future practice, knowledge, and skills in quality improvement and safety (QI/S) is a requisite element of graduate medical education. Despite many challenges, residency programs must consider new curricular innovations to meet the requirements. We report the effectiveness of a primary care QI/S curriculum and the role of the chief resident in quality and patient safety in facilitating it. Through the Veterans Administration Graduate Medical Education Enhancement Program, we added a position for a chief resident in quality and patient safety, and 4 full-time equivalent internal medicine residents, to develop the Primary Care Interprofessional Patient-Centered Quality Care Training Curriculum. The curriculum includes a first-or second-year, 1-month block rotation that serves as a foundational experience in QI/S and interprofessional care. The responsibilities of the chief resident in quality and patient safety included organizing and teaching the QI/S curriculum and mentoring resident projects. Evaluation included prerotation and postrotation surveys of self-assessed QI/S knowledge, abilities, skills, beliefs, and commitment (KASBC); an end-of-the-year KASBC; prerotation and postrotation knowledge test; and postrotation and faculty surveys. Comparisons of prerotation and postrotation KASBC indicated significant self-assessed improvements in 4 of 5 KASBC domains: knowledge (P < .001), ability (P < .001), skills (P < .001), and belief (P < .03), which were sustained on the end-of-the-year survey. The knowledge test demonstrated increased QI/S knowledge (P  =  .002). Results of the postrotation survey indicate strong satisfaction with the curriculum, with 76% (25 of 33) and 70% (23 of 33) of the residents rating the quality and safety curricula as always or usually educational. Most faculty members acknowledged that the chief resident in quality and patient safety enhanced both faculty and resident QI/S interest and

  11. Evaluating the Effectiveness of Two Teaching Strategies to Improve Nursing Students' Knowledge, Skills, and Attitudes About Quality Improvement and Patient Safety.

    Science.gov (United States)

    Maxwell, Karen L; Wright, Vivian H

    The purpose of this study was to evaluate two teaching strategies with regard to quality and safety education for nurses content on quality improvement and safety. Two groups (total of 64 students) participated in online learning or online learning in conjunction with a flipped classroom. A pretest/posttest control group design was used. The use of online modules in conjunction with the flipped classroom had a greater effect on increasing nursing students' knowledge of quality improvement than the use of online modules only. There was no statistically significant difference between the groups for safety.

  12. [Technological innovations in radiation oncology require specific quality controls].

    Science.gov (United States)

    Lenaerts, E; Mathot, M

    2014-01-01

    During the last decade, the field of radiotherapy has benefited from major technological innovations and continuously improving treatment efficacy, comfort and safety of patients. This mainly concerns the imaging techniques that allow 4D CT scan recording the respiratory phases, on-board imaging on linear accelerators that ensure perfect positioning of the patient for treatment and irradiation techniques that reduce very significantly the duration of treatment sessions without compromising quality of the treatment plan, including IMRT (Intensity Modulated Radiation Therapy) and VMAT (Volumetric Modulated Arc therapy). In this context of rapid technological change, it is the responsibility of medical physicists to regularly and precisely monitor the perfect functioning of new techniques to ensure patient safety. This requires the use of specific quality control equipment best suited to these new techniques. We will briefly describe the measurement system Delta4 used to control individualized treatment plan for each patient treated with VMAT technology.

  13. Intelligent Packaging Systems: Sensors and Nanosensors to Monitor Food Quality and Safety

    Directory of Open Access Journals (Sweden)

    Guillermo Fuertes

    2016-01-01

    Full Text Available The application of nanotechnology in different areas of food packaging is an emerging field that will grow rapidly in the coming years. Advances in food safety have yielded promising results leading to the development of intelligent packaging (IP. By these containers, it is possible to monitor and provide information of the condition of food, packaging, or the environment. This article describes the role of the different concepts of intelligent packaging. It is possible that this new technology could reach enhancing food safety, improving pathogen detection time, and controlling the quality of food and packaging throughout the supply chain.

  14. The complications of controlling agency time discretion: FDA review deadlines and postmarket drug safety.

    Science.gov (United States)

    Carpenter, Daniel; Chattopadhyay, Jacqueline; Moffitt, Susan; Nall, Clayton

    2012-01-01

    Public agencies have discretion on the time domain, and politicians deploy numerous policy instruments to constrain it. Yet little is known about how administrative procedures that affect timing also affect the quality of agency decisions. We examine whether administrative deadlines shape decision timing and the observed quality of decisions. Using a unique and rich dataset of FDA drug approvals that allows us to examine decision timing and quality, we find that this administrative tool induces a piling of decisions before deadlines, and that these “just-before-deadline” approvals are linked with higher rates of postmarket safety problems (market withdrawals, severe safety warnings, safety alerts). Examination of data from FDA advisory committees suggests that the deadlines may impede quality by impairing late-stage deliberation and agency risk communication. Our results both support and challenge reigning theories about administrative procedures, suggesting they embody expected control-expertise trade-offs, but may also create unanticipated constituency losses.

  15. The role of quality management in safety case development - Nagra's experience

    International Nuclear Information System (INIS)

    Schneider, Juerg W.; Zuidema, Piet

    2014-01-01

    This paper discusses the role of quality management (QM) in safety case development based on Nagra's experience from a broad range of projects. These include Project Gewahr (L/ILW and HLW, Nagra, 1985), the Wellenberg Project (L/ILW, Nagra, 1994), Project Opalinus Clay (HLW, Nagra, 2002a, 2002b), and recent project work needed in the context of the Swiss site selection process (L/ILW and HLW, Nagra, 2008a, 2008b, 2008c, 2010). Broadly speaking, Nagra's Quality Management policy is focused on ensuring: i) the quality of the disposal system (siting, design and implementation); ii) the quality of the underlying scientific understanding, which are seen as key elements of a credible safety case, along with the quality of the safety calculations themselves and of compiling the safety case, including the drawing of conclusions (Nagra, 2002a). All aspects of QM discussed in this paper should be seen in this context. (authors)

  16. Documenting Quality Improvement and Patient Safety Efforts: The Quality Portfolio. A Statement from the Academic Hospitalist Taskforce

    OpenAIRE

    Taylor, Benjamin B.; Parekh, Vikas; Estrada, Carlos A.; Schleyer, Anneliese; Sharpe, Bradley

    2013-01-01

    Physicians increasingly investigate, work, and teach to improve the quality of care and safety of care delivery. The Society of General Internal Medicine Academic Hospitalist Task Force sought to develop a practical tool, the quality portfolio, to systematically document quality and safety achievements. The quality portfolio was vetted with internal and external stakeholders including national leaders in academic medicine. The portfolio was refined for implementation to include an outlined fr...

  17. Safety implications of standardized continuous quality improvement programs in community pharmacy.

    Science.gov (United States)

    Boyle, Todd A; Ho, Certina; Mackinnon, Neil J; Mahaffey, Thomas; Taylor, Jeffrey M

    2013-06-01

    Standardized continuous quality improvement (CQI) programs combine Web-based technologies and standardized improvement processes, tools, and expectations to enable quality-related events (QREs) occurring in individual pharmacies to be shared with pharmacies in other jurisdictions. Because standardized CQI programs are still new to community pharmacy, little is known about how they impact medication safety. This research identifies key aspects of medication safety that change as a result of implementing a standardized CQI program. Fifty-three community pharmacies in Nova Scotia, Canada, adopted the SafetyNET-Rx standardized CQI program in April 2010. The Institute for Safe Medication Practices (ISMP) Canada's Medication Safety Self-Assessment (MSSA) survey was administered to these pharmacies before and 1 year into their use of the SafetyNET-Rx program. The nonparametric Wilcoxon signed-rank test was used to explore where changes in patient safety occurred as a result of SafetyNETRx use. Significant improvements occurred with quality processes and risk management, staff competence, and education, and communication of drug orders and other information. Patient education, environmental factors, and the use of devices did not show statistically significant changes. As CQI programs are designed to share learning from QREs, it is reassuring to see that the largest improvements are related to quality processes, risk management, staff competence, and education.

  18. Analysis approach for common cause failure on non-safety digital control system

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yun Goo; Oh, Eungse [Korea Hydro and Nuclear Power Co. Ltd., Daejeon (Korea, Republic of)

    2014-05-15

    The effects of common cause failure (CCF) on safety digital instrumentation and control (I and C) system had been considered in defense in depth and diversity coping analysis with safety analysis method. For the non-safety system, single failure had been considered for safety analysis. IEEE Std. 603-1991, Clause 5.6.3.1(2), 'Isolation' states that no credible failure on the non-safety side of an isolation device shall prevent any portion of a safety system from meeting its minimum performance requirements during and following any design basis event requiring that safety function. The software CCF is one of the credible failure on the non-safety side. In advanced digital I and C system, same hardware component is used for different control system and the defect in manufacture or common external event can generate CCF. Moreover, the non-safety I and C system uses complex software for its various function and software quality assurance for the development process is less severe than safety software for the cost effective design. Therefore the potential defects in software cannot be ignored and the effect of software CCF on non-safety I and C system is needed to be evaluated. This paper proposes the general process and considerations for the analysis of CCF on non-safety I and C system.

  19. Railing for safety: job demands, job control, and safety citizenship role definition.

    Science.gov (United States)

    Turner, Nick; Chmiel, Nik; Walls, Melanie

    2005-10-01

    This study investigated job demands and job control as predictors of safety citizenship role definition, that is, employees' role orientation toward improving workplace safety. Data from a survey of 334 trackside workers were framed in the context of R. A. Karasek's (1979) job demands-control model. High job demands were negatively related to safety citizenship role definition, whereas high job control was positively related to this construct. Safety citizenship role definition of employees with high job control was buffered from the influence of high job demands, unlike that of employees with low job control, for whom high job demands were related to lower levels of the construct. Employees facing both high job demands and low job control were less likely than other employees to view improving safety as part of their role orientation. Copyright (c) 2005 APA, all rights reserved.

  20. Quality and Safety Education for Nurses (QSEN): The Key is Systems Thinking.

    Science.gov (United States)

    Dolansky, Mary A; Moore, Shirley M

    2013-09-30

    Over a decade has passed since the Institute of Medicine's reports on the need to improve the American healthcare system, and yet only slight improvement in quality and safety has been reported. The Quality and Safety Education for Nurses (QSEN) initiative was developed to integrate quality and safety competencies into nursing education. The current challenge is for nurses to move beyond the application of QSEN competencies to individual patients and families and incorporate systems thinking in quality and safety education and healthcare delivery. This article provides a history of QSEN and proposes a framework in which systems thinking is a critical aspect in the application of the QSEN competencies. We provide examples of how using this framework expands nursing focus from individual care to care of the system and propose ways to teach and measure systems thinking. The conclusion calls for movement from personal effort and individual care to a focus on care of the system that will accelerate improvement of healthcare quality and safety.

  1. Safety-related control air systems

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    This Standard applies to those portions of the control air system that furnish air required to support, control, or operate systems or portions of systems that are safety related in nuclear power plants. This Standard relates only to the air supply system(s) for safety-related air operated devices and does not apply to the safety-related air operated device or to air operated actuators for such devices. The objectives of this Standard are to provide (1) minimum system design requirements for equipment, piping, instruments, controls, and wiring that constitute the air supply system; and (2) the system and component testing and maintenance requirements

  2. A complex tool and three simple approaches to improving quality assurance and safety in external radiotherapy

    International Nuclear Information System (INIS)

    Salinas, F; Sansogne, R; Arbiser, S; Suarez, V; Franco, M; Escobar, J

    2012-01-01

    Quality assurance and safety controls in radiation therapy delivery processes that involve the Physics Department of an institution are commonly time consuming tasks. Carrying out daily controls in very busy clinics without compromising patient schedule is challenging. This work describes the usage of Electronic Portal Imaging Devices in combination with some in-house software to simplify and systematize three different tasks of the Physics Department Quality Assurance Program, improving the easiness, reliability and velocity of daily tests (author)

  3. Consumer perception of meat quality and safety

    DEFF Research Database (Denmark)

    Brunsø, Karen; Grunert, Klaus G.; Bredahl, Lone

    2003-01-01

    The evaluation of meat quality and safety is not an easy task for consumers. In this article, the Total Food Quality Model will be introduced as a framework for understanding how consumers perceive meat quality, and results from a Danish study dealing with consumer perception and experience of beef...... will be presented. Consumers form expectations about the eating quality of meat at the point of purchase, based on prior experience and information available in the shopping environment, while the eating quality is experienced in the home during and after meal preparation. Results show that consumers have...... difficulty in evaluating meat quality, resulting in uncertainty and dissatisfaction, and reveal a need for educating consumers about evaluating eating quality during shopping....

  4. Management services, quality assurance, and safety

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    Broad technical and administrative support for the programmatic research and development activities of the Fusion Energy Division is provided by the Management Services Section and by the division's quality assurance (QA) and safety programs. Support is provided through effective communication with division programmatic staff and through the coordination of resources from disciplines outside the division. The QA activity in the division emphasizes the development and documentation of a QA program that conforms to national standards, the review and approval of engineering documents, supplier surveillance, identification and documentation of nonconforming items, audits, and QA assessments/plans. The division's safety activities include a formal safety program, emergency planning activities, and environmental protection services. Efforts devoted to the removal of hazardous wastes from division facilities were expanded during 1986

  5. The Role and Quality of Software Safety in the NASA Constellation Program

    Science.gov (United States)

    Layman, Lucas; Basili, Victor R.; Zelkowitz, Marvin V.

    2010-01-01

    In this study, we examine software safety risk in the early design phase of the NASA Constellation spaceflight program. Obtaining an accurate, program-wide picture of software safety risk is difficult across multiple, independently-developing systems. We leverage one source of safety information, hazard analysis, to provide NASA quality assurance managers with information regarding the ongoing state of software safety across the program. The goal of this research is two-fold: 1) to quantify the relative importance of software with respect to system safety; and 2) to quantify the level of risk presented by software in the hazard analysis. We examined 154 hazard reports created during the preliminary design phase of three major flight hardware systems within the Constellation program. To quantify the importance of software, we collected metrics based on the number of software-related causes and controls of hazardous conditions. To quantify the level of risk presented by software, we created a metric scheme to measure the specificity of these software causes. We found that from 49-70% of hazardous conditions in the three systems could be caused by software or software was involved in the prevention of the hazardous condition. We also found that 12-17% of the 2013 hazard causes involved software, and that 23-29% of all causes had a software control. Furthermore, 10-12% of all controls were software-based. There is potential for inaccuracy in these counts, however, as software causes are not consistently scoped, and the presence of software in a cause or control is not always clear. The application of our software specificity metrics also identified risks in the hazard reporting process. In particular, we found a number of traceability risks in the hazard reports may impede verification of software and system safety.

  6. FAO/IAEA International Symposium on Food Safety and Quality: Applications of Nuclear and Related Techniques, Vienna, Austria, 10−13 November 2014

    International Nuclear Information System (INIS)

    2015-01-01

    Ensuring food supply integrity is of the utmost importance in relation to food security, safety and quality, consumer protection and international trade. Control measures throughout the entire food production and supply chain are essential to maintain and assure this integrity. The fundamental purpose of the controls is to support food safety and quality, because both are essential and set the foundation for food security and consumer protection as well as facilitating both domestic and international trade. The need for methods to monitor and verify food safety and quality is evidenced by the ever growing list of food product recalls and incidents such as melamine, antibiotic and dioxin contamination. Food fraud (e.g. the adulteration of beef products with horse meat), the introduction of new technologies with potential food safety implications (e.g. nanotechnology) and environmental factors (e.g. climate change) further highlight the importance of continued refinement, development and innovation to improve food control measures. Effective techniques are necessary to help assess and manage risks and protect the consumer. These include food irradiation to treat food directly, as well as other nuclear and related technologies for tracing food products in order to verify their provenance or to detect and control contaminants. To explore some of these challenges experienced by many Member States, an International Symposium on Food Safety and Quality: Applications of Nuclear and Related Techniques was held in Vienna, Austria, from 10 to 13 November 2014, under the auspices of the Food and Environmental Protection Subprogramme.

  7. A computerized diagnostic system for nuclear plant control rooms based on statistical quality control

    International Nuclear Information System (INIS)

    Heising, C.D.; Grenzebach, W.S.

    1990-01-01

    In engineering science, statistical quality control techniques have traditionally been applied to control manufacturing processes. An application to commercial nuclear power plant maintenance and control is presented that can greatly improve safety. As a demonstration of such an approach to plant maintenance and control, a specific system is analyzed: the reactor coolant pumps of the St. Lucie Unit 2 nuclear power plant located in Florida. A 30-day history of the four pumps prior to a plant shutdown caused by pump failure and a related fire within the containment was analyzed. Statistical quality control charts of recorded variables were constructed for each pump, which were shown to go out of statistical control many days before the plant trip. The analysis shows that statistical process control methods can be applied as an early warning system capable of identifying significant equipment problems well in advance of traditional control room alarm indicators

  8. Microbiological safety and quality control of poultry products sold in retail chains of Saint Petersburg and Leningrad region.

    Directory of Open Access Journals (Sweden)

    A. K. Alieva

    2017-01-01

    Full Text Available Food safety and food raw materials is an important task which needs to be under government’s and public associations’ control, under enterprises which produce and sale them, and other economy departments. Nutrition is one of the most important factors influencing human health. To 70% alien substances of chemical and microbiological origin get into the human body with food. The heavy metals, nitrates, nitrites, pesticides, nitrosescomounds, mycotoxins, antibiotics, radionuclides and others are xenobiotics of chemical origin. The poultry products represented in commercial networks by poultry plants located in Saint-Petersburg and Leningrad region: “Roskar”, “Sinyavinskaya”, “North”, “Lebyazhye” were picked up for analysis. We used the bacteriological, virological, immunological, mycological, and statistical methods of research. Sanitary -hygienic or microbiological safety of food products was evaluated for the contenting of disease-causing (pathogenic microorganisms such as bacteria groups, coliforms, Staphylococcus, Salmonella and etc. in them. The poultry products sold in commercial networks of St. Petersburg were picked up for analysis. After processing the statistical were revealed 6 nosological forms where the leading position has finding colibacillosis – 27%. The number of positive samples for streptococcosis – 18%, staphylococcus – 8%, aspergillosis–2.6%, salmonellosis – 1.8%, pasteurellosis–1.6 %. The microbiological control of food products which can be the sources of infections should be regular for providing inhabitants with harmless poultry products. It is necessary to adopt and to use the modern microbiological criteria of food safety that will allow to realize the monitoring of their conformity with sanitary norms. The results of these analysis shows that the quality of poultry products sold in commercial networks of Saint Petersburg and the Leningrad region meet the standards.

  9. Radiation measurements and quality control

    International Nuclear Information System (INIS)

    McLaughlin, W.L.

    1977-01-01

    Accurate measurements are essential to research leading to a successful radiation process and to the commissioning of the process and the facility. On the other hand, once the process is in production, the importance to quality control of measuring radiation quantities (i.e., absorbed dose, dose rate, dose distribution) rather than various other parameters of the process (i.e. conveyor speed, dwell time, radiation field characteristics, product dimensions) is not clearly established. When the safety of the product is determined by the magnitude of the administered dose, as in radiation sterilization, waste control, or food preservation, accuracy and precision of the measurement of the effective dose are vital. Since physical dose measurements are usually simpler, more reliable and reproducible than biological testing of the product, there is a trend toward using standardized dosimetry for quality control of some processes. In many industrial products, however, such as vulcanized rubber, textiles, plastics, coatings, films, wire and cable, the effective dose can be controlled satisfactorily by controlling process variables or by product testing itself. In the measurement of radiation dose profiles by dosimetry, it is necessary to have suitable dose meter calibrations, to account for sources of error and imprecision, and to use correct statistical procedures in specifying dwell times or conveyor speeds and source and product parameters to achieve minimum and maximum doses within specifications. (author)

  10. Role of a quality management system in improving patient safety - laboratory aspects.

    Science.gov (United States)

    Allen, Lynn C

    2013-09-01

    The aim of this study is to describe how implementation of a quality management system (QMS) based on ISO 15189 enhances patient safety. A literature review showed that several European hospitals implemented a QMS based on ISO 9001 and assessed the impact on patient safety. An Internet search showed that problems affecting patient safety have occurred in a number of laboratories across Canada. The requirements of a QMS based on ISO 15189 are outlined, and the impact of the implementation of each requirement on patient safety is summarized. The Quality Management Program - Laboratory Services in Ontario is briefly described, and the experience of Ontario laboratories with Ontario Laboratory Accreditation, based on ISO 15189, is outlined. Several hospitals that implemented ISO 9001 reported either a positive impact or no impact on patient safety. Patient safety problems in Canadian laboratories are described. Implementation of each requirement of the QMS can be seen to have a positive effect on patient safety. Average laboratory conformance on Ontario Laboratory Accreditation is very high, and laboratories must address and resolve any nonconformities. Other standards, practices, and quality requirements may also contribute to patient safety. Implementation of a QMS based on ISO 15189 provides a solid foundation for quality in the laboratory and enhances patient safety. It helps to prevent patient safety issues; when such issues do occur, effective processes are in place for investigation and resolution. Patient safety problems in Canadian laboratories might have been prevented had effective QMSs been in place. Ontario Laboratory Accreditation has had a positive impact on quality in Ontario laboratories. Copyright © 2013 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

  11. Constitution of a centralised data base for the internal quality control in radiotherapy

    International Nuclear Information System (INIS)

    Fau, P.; Rodrigues, C.; Ruchaud, R.; Bravetti, J.

    2009-01-01

    The objective of this project was to implement a centralised data base of internal quality control in radiotherapy according to the criteria of the decree of A.f.s.s.a.p.s. (French agency of sanitary safety of health products on 27 july 2007, about the internal quality control of external radiotherapy facilities. The software on one year meets the objectives: compliance by comparison with A.f.s.s.a.p.s. criteria but particularly optimization of the centralisation and analysis of the internal quality controls. (N.C.)

  12. FOOD QUALITY AND SAFETY ASSURANCE IN TERMS OF LOSS AND WASTE LIMITATION

    Directory of Open Access Journals (Sweden)

    Maria Śmiechowska

    2016-06-01

    Full Text Available One of the greatest challenges of 21st century is satisfying the food needs of the fast growing population of the world. Food must fulfill quality and safety standards.  The access to safe and appropriate food is not the same everywhere.  Food excess and, in consequence, food waste is present in many regions of the world. This study is meant to explain the causes of food waste on the basis of the author’s own research and study results of other scientists. The lack of authenticity and falsification belong to the new factors endangering food safety and food waste related thereto. This analysis proves that the authenticity of food improves its safety through the implementation of quality management systems, the appropriate system of food labelling and food identification by means of applicable law regulations, supervision and control systems. Main aim of this study is to address why, even though there are so many quality standards and systems, a significant problem with food loss and waste constantly occurs. Waste-causing factors have been determined on the example of bread and the handling of unconsumed bread has been attempted in this study. Waste limiting actions are necessary as food production is significantly overburdening the natural environment and generating increasing amount of waste, hazardous to the clean air. 

  13. Quality assurance of radiotherapy in cancer treatment. Toward improvement of patient safety and quality of care

    International Nuclear Information System (INIS)

    Ishikura, Satoshi

    2008-01-01

    The process of radiotherapy (RT) is complex and involves understanding of the principles of medical physics, radiobiology, radiation safety, dosimetry, radiation treatment planning, simulation and interaction of radiation with other treatment modalities. Each step in the integrated process of RT needs quality control and quality assurance (QA) to prevent errors and to give high confidence that patients will receive the prescribed treatment correctly. Recent advances in RT, including intensity-modulated and image-guided RT, focus on the need for a systematic RTQA program that balances patient safety and quality with available resources. It is necessary to develop more formal error mitigation and process analysis methods, such as failure mode and effect analysis, to focus available QA resources optimally on process components. External audit programs are also effective. The International Atomic Energy Agency has operated both an on-site and off-site postal dosimetry audit to improve practice and to assure the dose from RT equipment. Several countries have adopted a similar approach for national clinical auditing. In addition, clinical trial QA has a significant role in enhancing the quality of care. The Advanced Technology Consortium has pioneered the development of an infrastructure and QA method for advanced technology clinical trials, including credentialing and individual case review. These activities have an impact not only on the treatment received by patients enrolled in clinical trials, but also on the quality of treatment administered to all patients treated in each institution, and have been adopted globally; by the USA, Europe and Japan also. (author)

  14. Quality assurance of radiotherapy in cancer treatment: toward improvement of patient safety and quality of care.

    Science.gov (United States)

    Ishikura, Satoshi

    2008-11-01

    The process of radiotherapy (RT) is complex and involves understanding of the principles of medical physics, radiobiology, radiation safety, dosimetry, radiation treatment planning, simulation and interaction of radiation with other treatment modalities. Each step in the integrated process of RT needs quality control and quality assurance (QA) to prevent errors and to give high confidence that patients will receive the prescribed treatment correctly. Recent advances in RT, including intensity-modulated and image-guided RT, focus on the need for a systematic RTQA program that balances patient safety and quality with available resources. It is necessary to develop more formal error mitigation and process analysis methods, such as failure mode and effect analysis, to focus available QA resources optimally on process components. External audit programs are also effective. The International Atomic Energy Agency has operated both an on-site and off-site postal dosimetry audit to improve practice and to assure the dose from RT equipment. Several countries have adopted a similar approach for national clinical auditing. In addition, clinical trial QA has a significant role in enhancing the quality of care. The Advanced Technology Consortium has pioneered the development of an infrastructure and QA method for advanced technology clinical trials, including credentialing and individual case review. These activities have an impact not only on the treatment received by patients enrolled in clinical trials, but also on the quality of treatment administered to all patients treated in each institution, and have been adopted globally; by the USA, Europe and Japan also.

  15. DASHBOARDS AND CONTROL CHARTS. EXPERIENCES IN IMPROVING SAFETY AT HANFORD WASHINGTON

    International Nuclear Information System (INIS)

    PREVETTE, S.S.

    2006-01-01

    The aim of this paper is to demonstrate the integration of safety methodology, quality tools, leadership, and teamwork at Hanford and their significant positive impact on safe performance of work. Dashboards, Leading Indicators, Control charts, Pareto Charts, Dr. W. Edward Deming's Red Bead Experiment, and Dr. Deming's System of Profound Knowledge have been the principal tools and theory of an integrated management system. Coupled with involved leadership and teamwork, they have led to significant improvements in worker safety and protection, and environmental restoration at one of the nation's largest nuclear cleanup sites

  16. Safety versus Security in the Quality Calculus

    DEFF Research Database (Denmark)

    Nielson, Hanne Riis; Nielson, Flemming

    2013-01-01

    Safety and security are both needed for ensuring that cyber-physical systems live up to expectations, but often an intelligent trade-off is called for, because sometimes it is impossible to obtain optimal safety at the same time as optimal security. In the context of the Quality Calculus we develop...... a type system for checking the extent to which safety and security goals have been met. Safety goals include showing that certain error configurations are in fact not reachable and hence do not require intelligent error handling. Security goals include showing that highly trusted communications can only...... of the implicit flow). This is illustrated on a worked example taken from the automotive sector and we conclude with a discussion of the theoretical properties of the type system....

  17. Improving health care quality and safety: the role of collective learning.

    Science.gov (United States)

    Singer, Sara J; Benzer, Justin K; Hamdan, Sami U

    2015-01-01

    Despite decades of effort to improve quality and safety in health care, this goal feels increasingly elusive. Successful examples of improvement are infrequently replicated. This scoping review synthesizes 76 empirical or conceptual studies (out of 1208 originally screened) addressing learning in quality or safety improvement, that were published in selected health care and management journals between January 2000 and December 2014 to deepen understanding of the role that collective learning plays in quality and safety improvement. We categorize learning activities using a theoretical model that shows how leadership and environmental factors support collective learning processes and practices, and in turn team and organizational improvement outcomes. By focusing on quality and safety improvement, our review elaborates the premise of learning theory that leadership, environment, and processes combine to create conditions that promote learning. Specifically, we found that learning for quality and safety improvement includes experimentation (including deliberate experimentation, improvisation, learning from failures, exploration, and exploitation), internal and external knowledge acquisition, performance monitoring and comparison, and training. Supportive learning environments are characterized by team characteristics like psychological safety, appreciation of differences, openness to new ideas social motivation, and team autonomy; team contextual factors including learning resources like time for reflection, access to knowledge, organizational capabilities; incentives; and organizational culture, strategy, and structure; and external environmental factors including institutional pressures, environmental dynamism and competitiveness and learning collaboratives. Lastly learning in the context of quality and safety improvement requires leadership that reinforces learning through actions and behaviors that affect people, such as coaching and trust building, and through

  18. Food safety and total quality management

    NARCIS (Netherlands)

    Barendsz, A.W.

    1998-01-01

    Food safety is a growing global concern not only because of its continuing importance for public health but also because of its impact on international trade. The application of total quality management (TQM) provides the best possible care by continuously improving products and services to meet or

  19. Management of safety and quality and the relationship with employee decisions in country grain elevators.

    Science.gov (United States)

    Mosher, G A; Keren, N; Freeman, S A; Hurburgh, C R

    2012-07-01

    Human factors play an important role in the management of safety and quality in an agricultural work environment. Although employee actions and decisions have been identified as a key component of successful occupational safety programs and quality management programs, little attention has been given to the employees' role in these types of programs. This research explored two safety relationships that have theoretical connections but little previous research: the relationship between safety climate and quality climate, and the relationship of the safety and quality climates between the organizational level and the group level within a workplace. Survey data were collected at three commercial grain handling facilities from 177 employees. Employees also participated in safety and quality decision-making simulations. Significant positive predictions were noted for safety and quality climate. Decision-making predictions are also discussed. This research suggests that organizational safety is an important predictor of group safety. In addition, recognizing the larger role that supervisors play in group workplace behavior, more should be done to increase employee perceptions of group-level involvement in quality climate to promote more quality-oriented decision-making by employees.

  20. 76 FR 7854 - Patient Safety Organizations: Voluntary Delisting From Quality Excellence, Inc./PSO

    Science.gov (United States)

    2011-02-11

    ... Arkansas Foundation for Medical Care, of its status as a Patient Safety Organization (PSO). The Patient Safety and Quality Improvement Act of 2005 (Patient Safety Act), Public Law 109-41, 42 U.S.C. 299b-21--b... DEPARTMENT OF HEALTH AND HUMAN SERVICES Agency for Healthcare Research and Quality Patient Safety...

  1. Control of safety and risk management software at the Savannah River Site

    International Nuclear Information System (INIS)

    Ades, M.J.; Toffer, H.; Crowe, R.D.

    1992-01-01

    As a part of its Reactor Operations Improvement Program at the Savannah River Site (SRS), Westinghouse Savannah River Company (WSRC), in cooperation with the Westinghouse Hanford Company, has developed and implemented software quality assurance (SQA) for computer codes essential to the safety and reliability of reactor operations. This effort includes the use of quality standards and attendant procedures developed for and applied to computer codes used in safety and risk management analyses. The certification process that was recently implemented is in compliance with site wide and departmental SQA requirements. Certification consists of preparing a specific verification and validation (V and V) plan, a configuration control plan, and user qualifications. Applicable documentation is reviewed to determine compliance with V and V and configuration control action items. The results of this review are documented and serve as a baseline for additional certification activities. Resource commitment and schedules are drawn up for each individual code to complete certification in accordance with SQA requirements

  2. Ion mobility spectrometry for food quality and safety.

    Science.gov (United States)

    Vautz, W; Zimmermann, D; Hartmann, M; Baumbach, J I; Nolte, J; Jung, J

    2006-11-01

    Ion mobility spectrometry is known to be a fast and sensitive technique for the detection of trace substances, and it is increasingly in demand not only for protection against explosives and chemical warfare agents, but also for new applications in medical diagnosis or process control. Generally, a gas phase sample is ionized by help of ultraviolet light, ss-radiation or partial discharges. The ions move in a weak electrical field towards a detector. During their drift they collide with a drift gas flowing in the opposite direction and, therefore, are slowed down depending on their size, shape and charge. As a result, different ions reach the detector at different drift times, which are characteristic for the ions considered. The number of ions reaching the detector are a measure of the concentration of the analyte. The method enables the identification and quantification of analytes with high sensitivity (ng l(-1) range). The selectivity can even be increased - as necessary for the analyses of complex mixtures - using pre-separation techniques such as gas chromatography or multi-capillary columns. No pre-concentration of the sample is necessary. Those characteristics of the method are preserved even in air with up to a 100% relative humidity rate. The suitability of the method for application in the field of food quality and safety - including storage, process and quality control as well as the characterization of food stuffs - was investigated in recent years for a number of representative examples, which are summarized in the following, including new studies as well: (1) the detection of metabolites from bacteria for the identification and control of their growth; (2) process control in food production - beer fermentation being an example; (3) the detection of the metabolites of mould for process control during cheese production, for quality control of raw materials or for the control of storage conditions; (4) the quality control of packaging materials during

  3. Procurement and quality control of components important to safety in nuclear engineering projects

    International Nuclear Information System (INIS)

    Zhang Zhihua; Zhang Yiyun

    2006-01-01

    The procurement and quality control of components is a very important work in the nuclear engineering. This paper introduces the project management techniques, such as how to make a plan of components purchase in nuclear engineering. This paper discussed the classification of components, evaluation of the potential suppliers, invitation of bids, exchange of design details with the suppliers, quality assurance and quality assurance audit, and the equipment checks before acceptance and some engineering experiences. (authors)

  4. 38 CFR 17.155 - Minimum standards of safety and quality for automotive adaptive equipment.

    Science.gov (United States)

    2010-07-01

    ... safety and quality for automotive adaptive equipment. 17.155 Section 17.155 Pensions, Bonuses, and... Minimum standards of safety and quality for automotive adaptive equipment. (a) The Under Secretary for... officials that it meets implicit standards of safety and quality adopted by the industry or as later...

  5. 77 FR 42738 - Patient Safety Organizations: Voluntary Relinquishment From the Coalition for Quality and Patient...

    Science.gov (United States)

    2012-07-20

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Agency for Healthcare Research and Quality Patient Safety Organizations: Voluntary Relinquishment From the Coalition for Quality and Patient Safety of Chicagoland (CQPS.... SUMMARY: The Patient Safety and Quality Improvement Act of 2005 (Patient Safety Act), Public Law 109-41,42...

  6. Six sigma tools for a patient safety-oriented, quality-checklist driven radiation medicine department.

    Science.gov (United States)

    Kapur, Ajay; Potters, Louis

    2012-01-01

    The purpose of this work was to develop and implement six sigma practices toward the enhancement of patient safety in an electronic, quality checklist-driven, multicenter, paperless radiation medicine department. A quality checklist process map (QPM), stratified into consultation through treatment-completion stages was incorporated into an oncology information systems platform. A cross-functional quality management team conducted quality-function-deployment and define-measure-analyze-improve-control (DMAIC) six sigma exercises with a focus on patient safety. QPM procedures were Pareto-sorted in order of decreasing patient safety risk with failure mode and effects analysis (FMEA). Quantitative metrics for a grouped set of highest risk procedures were established. These included procedural delays, associated standard deviations and six sigma Z scores. Baseline performance of the QPM was established over the previous year of usage. Data-driven analysis led to simplification, standardization, and refinement of the QPM with standard deviation, slip-day reduction, and Z-score enhancement goals. A no-fly policy (NFP) for patient safety was introduced at the improve-control DMAIC phase, with a process map interlock imposed on treatment initiation in the event of FMEA-identified high-risk tasks being delayed or not completed. The NFP was introduced in a pilot phase with specific stopping rules and the same metrics used for performance assessments. A custom root-cause analysis database was deployed to monitor patient safety events. Relative to the baseline period, average slip days and standard deviations for the risk-enhanced QPM procedures improved by over threefold factors in the NFP period. The Z scores improved by approximately 20%. A trend for proactive delays instead of reactive hard stops was observed with no adverse effects of the NFP. The number of computed potential no-fly delays per month dropped from 60 to 20 over a total of 520 cases. The fraction of computed

  7. Research of quality control during development of NPP DCS 1E classified software

    International Nuclear Information System (INIS)

    Shi Weihua; Lu Zhenguo; Xie Qi

    2012-01-01

    The Nuclear safety depends on right behavior of 1E software, which is a important part of 1E DCS system. Nowadays, user focus on good function of 1E system, but pay little attention to quality control of 1E software. In fact, it's declared in IEC61513 and IEC60880 that 1E software should under strict quality control during all stages of development. This article is related to the practice of 1E DCS system quality control and explores the QC surveillance for 1E software from the user's point of view. (authors)

  8. Association between product quality control and process quality control of bulk milk

    NARCIS (Netherlands)

    Velthuis, A.; Asseldonk, van M.A.P.M.

    2010-01-01

    Assessment of dairy-milk quality is based on product quality control (testing bulk-milk samples) and process quality control (auditing dairy farms). It is unknown whether process control improves product quality. To quantify possible association between product control and process control a

  9. IOT for Agriculture: Food Quality and Safety

    Science.gov (United States)

    Witjaksono, Gunawan; Abdelkreem Saeed Rabih, Almur; Yahya, Noorhana bt; Alva, Sagir

    2018-03-01

    Food is the main energy source for the living beings; as such food quality and safety have been in the highest demand throughout the human history. Internet of things (IOT) is a technology with a vision to connect anything at anytime and anywhere. Utilizing IOT in the food supply chain (FSC) is believed to enhance the quality of life by tracing and tracking the food conditions and live-sharing the obtained data with the consumers or the FSC supervisors. Currently, full application of IOT in the FSC is still in the developing stage and there is a big gap for improvements. The purpose of this paper is to explore the possibility of applying IOT for agriculture to trace and track food quality and safety. Mobile application for food freshness investigation was successfully developed and the results showed that consumer mobile camera could be used to test the freshness of food. By applying the IOT technology this information could be shared with all the consumers and also the supervisors.

  10. Quantitative safety assessment of air traffic control systems through system control capacity

    Science.gov (United States)

    Guo, Jingjing

    Quantitative Safety Assessments (QSA) are essential to safety benefit verification and regulations of developmental changes in safety critical systems like the Air Traffic Control (ATC) systems. Effectiveness of the assessments is particularly desirable today in the safe implementations of revolutionary ATC overhauls like NextGen and SESAR. QSA of ATC systems are however challenged by system complexity and lack of accident data. Extending from the idea "safety is a control problem" in the literature, this research proposes to assess system safety from the control perspective, through quantifying a system's "control capacity". A system's safety performance correlates to this "control capacity" in the control of "safety critical processes". To examine this idea in QSA of the ATC systems, a Control-capacity Based Safety Assessment Framework (CBSAF) is developed which includes two control capacity metrics and a procedural method. The two metrics are Probabilistic System Control-capacity (PSC) and Temporal System Control-capacity (TSC); each addresses an aspect of a system's control capacity. And the procedural method consists three general stages: I) identification of safety critical processes, II) development of system control models and III) evaluation of system control capacity. The CBSAF was tested in two case studies. The first one assesses an en-route collision avoidance scenario and compares three hypothetical configurations. The CBSAF was able to capture the uncoordinated behavior between two means of control, as was observed in a historic midair collision accident. The second case study compares CBSAF with an existing risk based QSA method in assessing the safety benefits of introducing a runway incursion alert system. Similar conclusions are reached between the two methods, while the CBSAF has the advantage of simplicity and provides a new control-based perspective and interpretation to the assessments. The case studies are intended to investigate the

  11. Quality Control Applications

    CERN Document Server

    Chorafas, Dimitris N

    2013-01-01

    Quality control is a constant priority in electrical, mechanical, aeronautical, and nuclear engineering – as well as in the vast domain of electronics, from home appliances to computers and telecommunications. Quality Control Applications provides guidance and valuable insight into quality control policies; their methods, their implementation, constant observation and associated technical audits. What has previously been a mostly mathematical topic is translated here for engineers concerned with the practical implementation of quality control. Once the fundamentals of quality control are established, Quality Control Applications goes on to develop this knowledge and explain how to apply it in the most effective way. Techniques are described and supported using relevant, real-life, case studies to provide detail and clarity for those without a mathematical background. Among the many practical examples, two case studies dramatize the importance of quality assurance: A shot-by-shot analysis of the errors made ...

  12. Design of agricultural product quality safety retrospective supervision system of Jiangsu province

    Science.gov (United States)

    Wang, Kun

    2017-08-01

    In store and supermarkets to consumers can trace back agricultural products through the electronic province card to query their origin, planting, processing, packaging, testing and other important information and found that the problems. Quality and safety issues can identify the responsibility of the problem. This paper designs a retroactive supervision system for the quality and safety of agricultural products in Jiangsu Province. Based on the analysis of agricultural production and business process, the goal of Jiangsu agricultural product quality safety traceability system construction is established, and the specific functional requirements and non-functioning requirements of the retroactive system are analyzed, and the target is specified for the specific construction of the retroactive system. The design of the quality and safety traceability system in Jiangsu province contains the design of the overall design, the trace code design and the system function module.

  13. Safety and security analysis for distributed control system in nuclear power plants

    International Nuclear Information System (INIS)

    Lu Zhigang; Liu Baoxu

    2011-01-01

    The Digital Distributed Control System (DCS) is the core that manages all monitoring and operation tasks in a Nuclear Power Plant (NPP). So, Digital Distributed Control System in Nuclear Power Plant has strict requirements for control and automation device safety and security due to many factors. In this article, factors of safety are analyzed firstly, while placing top priority on reliability, quality of supply and stability have also been carefully considered. In particular, advanced digital and electronic technologies are adopted to maintain sufficient reliability and supervisory capabilities in nuclear power plants. Then, security of networking and information technology have been remarked, several design methodologies considering the security characteristics are suggested. Methods and technologies of this article are being used in testing and evaluation for a real implement of a nuclear power plant in China. (author)

  14. Quality and Safety Aspects of Cereals (Wheat) and Their Products.

    Science.gov (United States)

    Varzakas, Theo

    2016-11-17

    Cereals and, most specifically, wheat are described in this chapter highlighting on their safety and quality aspects. Moreover, wheat quality aspects are adequately addressed since they are used to characterize dough properties and baking quality. Determination of dough properties is also mentioned and pasta quality is also described in this chapter. Chemometrics-multivariate analysis is one of the analyses carried out. Regarding production weighing/mixing of flours, kneading, extruded wheat flours, and sodium chloride are important processing steps/raw materials used in the manufacturing of pastry products. Staling of cereal-based products is also taken into account. Finally, safety aspects of cereal-based products are well documented with special emphasis on mycotoxins, acrylamide, and near infrared methodology.

  15. Quality control programme for radiotherapy

    International Nuclear Information System (INIS)

    Campos de Araujo, A.M.; Viegas, C.C.B.; Viamonte, A.M.

    2002-01-01

    A 3 years pilot programme started in January 2000 with 33 philanthropic cancer institutions that provides medical services to 60% of the patients from the national social security system. Brazil has today 161 radiotherapy services (144 operating with megavoltage equipment). These 33 institutions are distributed over 19 Brazilian states. The aim of this programme is: To create conditions to allow the participants to apply the radiotherapy with quality and efficacy; To promote up dating courses for the physicians, physicists and technicians of these 33 Institutions. With the following objectives: To recommend dosimetric and radiological protection procedures in order to guarantee the tumor prescribed dose and safe working conditions; To help in establishing and implementing these procedures. The main activities are: local quality control evaluations, postal TLD audits in reference conditions, postal TLD audits in off axis conditions and training. The local quality control program has already evaluated 22 institutions with 43 machines (25 Co-60 and 18 linear accelerators). In these visits we perform dosimetric, electrical, mechanical and safety tests. As foreseen, we found more problems among the old Co-60 machines i.e., field flatness, size, symmetry and relative output factors; lasers positioning system alignment; optical distance indicator; radiation and light field coincidence; optical and mechanical distance indicators agreement, than among the linear accelerators i.e., field flatness and size; lasers positioning system alignment; tray interlocking and wedge filter factors

  16. Suggestion for improvement of PET quality control tests in Brazil

    International Nuclear Information System (INIS)

    Ferreira, Fernanda C.L.; Magalhaes, Cinthia M.S.; Souza, Divanizia N.

    2009-01-01

    Nowadays nuclear medicine has a considerable importance among the other medical specialties. This medical specialty utilizes high-tech equipment for imaging in the diagnosis, obtaining information on the clinical functionality of organs and systems of the human body through the use of radioisotopes . In view of the importance of guaranteeing the image quality in SPECT and PET systems, enabling patients not repeat exams due to lack of quality control of equipment used in nuclear medicine, this paper aims to present a possible suggestion to update the quality control tests needed for quality assurance of nuclear medicine services. They were considered the requirements of the National Commission of Nuclear Energy (CNEN) and the National Health Surveillance Agency (ANVISA) in Brazil. The minimum requirements to be defined for inclusion of quality control tests on PET in the standard CNEN are extremely important because they will guide the evaluation of PET systems, determining the quality control tests to be performed. And those tests for PET will be a regulatory requirement by the CNEN and ANVISA. As the National Health Surveillance Agency has already publication of RDC 38 with recommendations for services of nuclear medicine. This study will continue with evaluation of PET systems and presenting the tests of quality control with additional objects and simulators to ensure safety in PET systems have not standardized in nuclear medicine services in Brazil. (author)

  17. Food-packaging interactions influencing quality and safety.

    Science.gov (United States)

    Hotchkiss, J H

    1997-01-01

    Interactions between foods and packaging can be detrimental to quality and/or safety. Changes in product flavour due to aroma sorption and the transfer of undesirable flavours from packaging to foods are important mechanisms of deterioration when foods are packaged in polymer-based materials. Careful consideration must be given to those factors affecting such interactions when selecting packaging materials in order to maximize product quality, safety, and shelf-life while minimizing undesirable changes. Product considerations include sensitivity to flavour and related deteriorations, colour changes, vitamin loss, microbial activity, and amount of flavour available. Storage considerations include temperature, time, and processing method. Polymer considerations include type of polymer and processing method, volume or mass of polymer to product ratio, and whether the interaction is Fickian or non-Fickian. Methodology to determine the extent of such interactions must be developed. Direct interactions between food and packaging are not necessarily detrimental. The same principles governing undesirable interactions can be used to affect desirable outcomes. Examples include films which directly intercept or absorb oxygen, inhibit microorganisms, remove undesirable flavours by sorption, or indicate safety and product shelf-life.

  18. Software quality assurance plans for safety-critical software

    International Nuclear Information System (INIS)

    Liddle, P.

    2006-01-01

    Application software is defined as safety-critical if a fault in the software could prevent the system components from performing their nuclear-safety functions. Therefore, for nuclear-safety systems, the AREVA TELEPERM R XS (TXS) system is classified 1E, as defined in the Inst. of Electrical and Electronics Engineers (IEEE) Std 603-1998. The application software is classified as Software Integrity Level (SIL)-4, as defined in IEEE Std 7-4.3.2-2003. The AREVA NP Inc. Software Program Manual (SPM) describes the measures taken to ensure that the TELEPERM XS application software attains a level of quality commensurate with its importance to safety. The manual also describes how TELEPERM XS correctly performs the required safety functions and conforms to established technical and documentation requirements, conventions, rules, and standards. The program manual covers the requirements definition, detailed design, integration, and test phases for the TELEPERM XS application software, and supporting software created by AREVA NP Inc. The SPM is required for all safety-related TELEPERM XS system applications. The program comprises several basic plans and practices: 1. A Software Quality-Assurance Plan (SQAP) that describes the processes necessary to ensure that the software attains a level of quality commensurate with its importance to safety function. 2. A Software Safety Plan (SSP) that identifies the process to reasonably ensure that safety-critical software performs as intended during all abnormal conditions and events, and does not introduce any new hazards that could jeopardize the health and safety of the public. 3. A Software Verification and Validation (V and V) Plan that describes the method of ensuring the software is in accordance with the requirements. 4. A Software Configuration Management Plan (SCMP) that describes the method of maintaining the software in an identifiable state at all times. 5. A Software Operations and Maintenance Plan (SO and MP) that

  19. Quality and safety implications of emergency department information systems.

    Science.gov (United States)

    Farley, Heather L; Baumlin, Kevin M; Hamedani, Azita G; Cheung, Dickson S; Edwards, Michael R; Fuller, Drew C; Genes, Nicholas; Griffey, Richard T; Kelly, John J; McClay, James C; Nielson, Jeff; Phelan, Michael P; Shapiro, Jason S; Stone-Griffith, Suzanne; Pines, Jesse M

    2013-10-01

    The Health Information Technology for Economic and Clinical Health Act of 2009 and the Centers for Medicare & Medicaid Services "meaningful use" incentive programs, in tandem with the boundless additional requirements for detailed reporting of quality metrics, have galvanized hospital efforts to implement hospital-based electronic health records. As such, emergency department information systems (EDISs) are an important and unique component of most hospitals' electronic health records. System functionality varies greatly and affects physician decisionmaking, clinician workflow, communication, and, ultimately, the overall quality of care and patient safety. This article is a joint effort by members of the Quality Improvement and Patient Safety Section and the Informatics Section of the American College of Emergency Physicians. The aim of this effort is to examine the benefits and potential threats to quality and patient safety that could result from the choice of a particular EDIS, its implementation and optimization, and the hospital's or physician group's approach to continuous improvement of the EDIS. Specifically, we explored the following areas of potential EDIS safety concerns: communication failure, wrong order-wrong patient errors, poor data display, and alert fatigue. Case studies are presented that illustrate the potential harm that could befall patients from an inferior EDIS product or suboptimal execution of such a product in the clinical environment. The authors have developed 7 recommendations to improve patient safety with respect to the deployment of EDISs. These include ensuring that emergency providers actively participate in selection of the EDIS product, in the design of processes related to EDIS implementation and optimization, and in the monitoring of the system's ongoing success or failure. Our recommendations apply to emergency departments using any type of EDIS: custom-developed systems, best-of-breed vendor systems, or enterprise systems

  20. Quality and Safety Assurance - Priority Task at Nuclear Power Projects Implementation

    International Nuclear Information System (INIS)

    Nenkova, B.; Manchev, B.; Tomov, E.

    2010-01-01

    Quality and safety assurance at implementation of nuclear power engineering projects is important and difficult task for realization. Many problems arise during this process, when many companies from different countries participate, with various kinds of activities and services provided. The scope of activities necessary for quality and safety assurance is therefore quite expanded and diverse. In order to increase the safety and reliability of Kozloduy NPP Plc (KNPP) Units 5 and 6, as well as to bring the units in conformity with the newest international requirements for quality and safety in the field of nuclear energy, a program for their modernization on the basis of different technical studies and assessments was implemented. The Units 5 and 6 Modernization Program of Kozloduy Nuclear Power Plant was composed of 212 modifications aimed to improve the safety, operability, and reliability of the Units. The Program was realized by stages during yearly planned outages since year 2002 to 2007, without additional outages. A major Program Objective was to extend the Units Life Time in at least 15 Years, under a continuous, safe, and reliable operation. The Modernization Program of Units 5 and 6 of the Bulgarian Nuclear Power Plant in Kozloduy was the first and for the time being the only one in the world, program in the field of nuclear power engineering, by which the full scope of recommendations for improvement of the Kozloduy NPP units was applied. The main goal of the National Electric Company, which is the Employer for the construction of new nuclear facility in Bulgaria, is after completion of all activities regarding construction of Belene NPP the plant to meet or exceed the requirements of the respective national and international quality and safety codes and standards, as well as the IAEA guidelines, as they are established. The objective of this report is to describe different aspects of the quality assurance according to the requirements of quality and

  1. Microbiological quality control practices at Australian Radioisotopes

    International Nuclear Information System (INIS)

    Saunders, M.

    1987-01-01

    As a domestic manufacturer of therapeutic substances, Australian Radioisotopes (ARI) must adhere to guidelines set out by the Commonwealth Department of Health in the Code of Good Manufacturing Practices for Therapeutic Goods 1983 (GMP). The GMP gives guidelines for staff training, building requirements, sanitation, documentation and quality control practices. These guidelines form the basis for regular audits performed by officers of the National Biological Standards Laboratories. At Lucas Heights, ARI has combined the principles of the GMP with the overriding precautions introduced for environmental and staff safety and protection. Its policy is to maintain a high level of quality assurance for product identity, purity and sterility and apyrogenicity during all stages of product manufacture

  2. Basic quality control in diagnostic radiology

    International Nuclear Information System (INIS)

    Wikstrom, Erik

    2016-01-01

    Along the route toward regular performance of Quality Control in the Diagnostic Imaging sector there are a number of balances to negotiate: Patient/Staff safety considerations vs Regulatory compliance vs Performance of modern equipment vs Clinic's Productivity. At first glance these ambitions may seem in conflict. The tests performed to meet regulatory requirements may or may not bear any semblance to real clinical measurement scenarios. And the process of collecting the data from the quality assurance tests may induce a system down- time that adversely affects the clinic's overall productivity. Furthermore, the time it takes to complete the analysis of the test data and provide the report required to take the facility back into operation is time wasted for patients waiting for a diagnostic imaging exam

  3. Quality assurance of the modernized Dukovany I and C safety system software

    International Nuclear Information System (INIS)

    Karpeta, C.

    2005-01-01

    The approach to quality assurance of the software that implements the instrumentation and control functions for safety category A as per IEC 61226, which has been adopted within the 'NPP Dukovany I and C Refurbishment' project, is described. A survey of the requirements for software quality assurance of the systems that initiate protection interventions in the event of anticipated operational occurrences or accident conditions is given. The software development process applied by the system designers and manufacturers, from the software requirements specification phase to the software testing phase, is outlined. Basic information on technical audits of the software development process is also provided. (orig.)

  4. Organizing quality control programmes

    International Nuclear Information System (INIS)

    Hjardemaal, O.

    1989-01-01

    When procuring new equipment, performance and safety should be specified, if possible by reference to international standards. Some of the characteristics of the International Electrotechnical Commission (IEC) standard for X-ray generators, in particular the accuracy of the operating data, are described. The quality control tests to be performed after installation comprise acceptance test, status test and constancy test. The first two involve absolute measurements and will be the responsibility of physicists or engineers. Apparently limiting values stipulated by users are a factor of two lower than the limits of the IEC standard. By means of an example it is shown that modern X-ray generators can meet the lower limits of the users without problems. In order to obtain optimum initial quality when procuring new equipment operating data, limiting values must be specified and must be verified by acceptance testing, etc. However, in many countries physicists and engineers are not available for this job. A relatively uncomplicated test object can be used by radiographers for checks on fluoroscopic systems. The findings from such tests in Denmark are compared with other published findings and good agreement is found. Therefore it is proposed that such uncomplicated tests could form the basis for quality evaluation. (author)

  5. Improving health care quality and safety: the role of collective learning

    Directory of Open Access Journals (Sweden)

    Singer SJ

    2015-11-01

    Full Text Available Sara J Singer,1–4 Justin K Benzer,4–6 Sami U Hamdan4,6 1Department of Health Policy and Management, Harvard T.H. Chan School of Public Health, Boston, MA, USA; 2Department of Medicine, Harvard Medical School, Boston, MA, USA; 3Mongan Institute for Health Policy, Massachusetts General Hospital, Boston, MA, USA; 4Center for Healthcare Organization and Implementation Research, VA Boston Healthcare System, Boston, MA, USA; 5VISN 17 Center of Excellence for Research on Returning War Veterans, Waco, TX, USA; 6Department of Health Policy and Management, Boston University School of Public Health, Boston, MA, USA Abstract: Despite decades of effort to improve quality and safety in health care, this goal feels increasingly elusive. Successful examples of improvement are infrequently replicated. This scoping review synthesizes 76 empirical or conceptual studies (out of 1208 originally screened addressing learning in quality or safety improvement, that were published in selected health care and management journals between January 2000 and December 2014 to deepen understanding of the role that collective learning plays in quality and safety improvement. We categorize learning activities using a theoretical model that shows how leadership and environmental factors support collective learning processes and practices, and in turn team and organizational improvement outcomes. By focusing on quality and safety improvement, our review elaborates the premise of learning theory that leadership, environment, and processes combine to create conditions that promote learning. Specifically, we found that learning for quality and safety improvement includes experimentation (including deliberate experimentation, improvisation, learning from failures, exploration, and exploitation, internal and external knowledge acquisition, performance monitoring and comparison, and training. Supportive learning environments are characterized by team characteristics like psychological

  6. Quality and safety in Spain; La calidad y seguridad industrial en Espana

    Energy Technology Data Exchange (ETDEWEB)

    Prieto Barrio, J. M.; Martinez Martin, D. J.

    2015-07-01

    For three decades, and after the entry of Spain into the EU, it has been developed a regulatory, stable but evolving, framework that has allowed to create the conditions and structures to have stringent safety conditions of products and manufacturing facilities, as well as all the activities necessary for their certification and control. This development has been possible, among others, by the work of impulse and coordination of the Ministry of industry, Energy and Tourism, and particularly of the quality and Industrial safety sub directorate. On the other hand it has been developed a quality infrastructure that has, at the State level, with a standardisation (AENOR) entity and an accreditation body (ENAC) with recognized prestige around the world. In this article, in the first part, a list the regulations which apply to products and manufacturing facilities is shown, as well as explain the role played by standards and accreditation system in industrial safety and the factor of competitiveness that this entails for our industrial sector, and, in the second part, the institutional role of the Ministry and, the aforementioned Sub directorate, is described. The aim of the article is to be a descriptive reference of the current regulatory framework as well as the role of the State in this process. (Author)

  7. Factors impacting on the microbiological quality and safety of ...

    African Journals Online (AJOL)

    hope&shola

    2010-12-06

    Dec 6, 2010 ... microbiological quality and safety of processed hake. Samples were collected along the processing line; the general microbiological quality (mesophylic and psychrotrophic aerobic plate counts), total. Vibrio species and common fish spoilage bacterial counts were performed. The results constantly showed ...

  8. Study on the Problems and Countermeasure in the Animal Products Quality and Safety

    Institute of Scientific and Technical Information of China (English)

    Shishan; WANG

    2013-01-01

    As the supply chain of animal products is long,there are many factors which would influence the quality safety of animal production.Therefore,by focusing on the present and having a vision for future,Jiaozuo government promulgated Ten Polices on the Food Safety in Jiaozuo City,which pushed forward the technological development,intensified measures to monitor the quality of animal products,set up a series of mechanism,and provided reference for the food quality and safety monitoring.

  9. Food safety and nutritional quality for the prevention of non communicable diseases: the Nutrient, hazard Analysis and Critical Control Point process (NACCP).

    Science.gov (United States)

    Di Renzo, Laura; Colica, Carmen; Carraro, Alberto; Cenci Goga, Beniamino; Marsella, Luigi Tonino; Botta, Roberto; Colombo, Maria Laura; Gratteri, Santo; Chang, Ting Fa Margherita; Droli, Maurizio; Sarlo, Francesca; De Lorenzo, Antonino

    2015-04-23

    The important role of food and nutrition in public health is being increasingly recognized as crucial for its potential impact on health-related quality of life and the economy, both at the societal and individual levels. The prevalence of non-communicable diseases calls for a reformulation of our view of food. The Hazard Analysis and Critical Control Point (HACCP) system, first implemented in the EU with the Directive 43/93/CEE, later replaced by Regulation CE 178/2002 and Regulation CE 852/2004, is the internationally agreed approach for food safety control. Our aim is to develop a new procedure for the assessment of the Nutrient, hazard Analysis and Critical Control Point (NACCP) process, for total quality management (TMQ), and optimize nutritional levels. NACCP was based on four general principles: i) guarantee of health maintenance; ii) evaluate and assure the nutritional quality of food and TMQ; iii) give correct information to the consumers; iv) ensure an ethical profit. There are three stages for the application of the NACCP process: 1) application of NACCP for quality principles; 2) application of NACCP for health principals; 3) implementation of the NACCP process. The actions are: 1) identification of nutritional markers, which must remain intact throughout the food supply chain; 2) identification of critical control points which must monitored in order to minimize the likelihood of a reduction in quality; 3) establishment of critical limits to maintain adequate levels of nutrient; 4) establishment, and implementation of effective monitoring procedures of critical control points; 5) establishment of corrective actions; 6) identification of metabolic biomarkers; 7) evaluation of the effects of food intake, through the application of specific clinical trials; 8) establishment of procedures for consumer information; 9) implementation of the Health claim Regulation EU 1924/2006; 10) starting a training program. We calculate the risk assessment as follows

  10. Safety critical FPGA-based NPP instrumentation and control systems: assessment, development and implementation

    International Nuclear Information System (INIS)

    Bakhmach, E. S.; Siora, A. A.; Tokarev, V. I.; Kharchenko, V. S.; Sklyar, V. V.; Andrashov, A. A.

    2010-10-01

    The stages of development, production, verification, licensing and implementation methods and technologies of safety critical instrumentation and control systems for nuclear power plants (NPP) based on FPGA (Field Programmable Gates Arrays) technologies are described. A life cycle model and multi-version technologies of dependability and safety assurance of FPGA-based instrumentation and control systems are discussed. An analysis of NPP instrumentation and control systems construction principles developed by Research and Production Corporation Radiy using FPGA-technologies and results of these systems implementation and operation at Ukrainian and Bulgarian NPP are presented. The RADIY TM platform has been designed and developed by Research and Production Corporation Radiy, Ukraine. The main peculiarity of the RADIY TM platform is the use of FPGA as programmable components for logic control operation. The FPGA-based RADIY TM platform used for NPP instrumentation and control systems development ensures sca lability of system functions types, volume and peculiarities (by changing quantity and quality of sensors, actuators, input/output signals and control algorithms); sca lability of dependability (safety integrity) (by changing a number of redundant channel, tiers, diagnostic and reconfiguration procedures); sca lability of diversity (by changing types, depth and method of diversity selection). (Author)

  11. Impact of Performance Obstacles on Intensive Care Nurses‘ Workload, Perceived Quality and Safety of Care, and Quality of Working Life

    Science.gov (United States)

    Gurses, Ayse P; Carayon, Pascale; Wall, Melanie

    2009-01-01

    Objectives To study the impact of performance obstacles on intensive care nurses‘ workload, quality and safety of care, and quality of working life (QWL). Performance obstacles are factors that hinder nurses‘ capacity to perform their job and that are closely associated with their immediate work system. Data Sources/Study Setting Data were collected from 265 nurses in 17 intensive care units (ICUs) between February and August 2004 via a structured questionnaire, yielding a response rate of 80 percent. Study Design A cross-sectional study design was used. Data were analyzed by correlation analyses and structural equation modeling. Principal Findings Performance obstacles were found to affect perceived quality and safety of care and QWL of ICU nurses. Workload mediated the impact of performance obstacles with the exception of equipment-related issues on perceived quality and safety of care as well as QWL. Conclusions Performance obstacles in ICUs are a major determinant of nursing workload, perceived quality and safety of care, and QWL. In general, performance obstacles increase nursing workload, which in turn negatively affect perceived quality and safety of care and QWL. Redesigning the ICU work system to reduce performance obstacles may improve nurses‘ work. PMID:19207589

  12. Fisheries and aquaculture industries involvement to control product health and quality safety to satisfy consumer-driven objectives on retail markets in Europe.

    Science.gov (United States)

    Roth, Eva; Rosenthal, Harald

    2006-01-01

    Over the past years the export of agricultural and fishery products from developing countries has substantially increased to markets within the OECD. Retailers and importers are expanding their international operations to meet consumer demands for year-round delivery of products. Moreover, consumers have become increasingly concerned about the safety of food, including those derived from aquatic resources [FAO/NACA/WHO Joint Study Group, 1999. Report food safety issues associated with products from aquaculture. WHO Technical Report Series No 883: VII, pp. 1-55]. Governments and leading businesses are responding by imposing new safety regulations and standards to the international food system (e.g. HACCP, EUREP-GAP), product liability and labeling [Reilly, A., Howgate, P., Käferstein, F., 1997. Safety hazards and the application of HACCP in aquaculture. In: Proceedings of the Second International Conference on Fish Inspection and Quality Control: A Global Focus, Arlington, VA, 19-24 May 1996. Technomic Publishing, Lancaster, PA, pp. 353-373]. Initial concerns for imports of aquacultural products from developing to industrialized countries focussed on bacterial contamination [Buras, N. 1993. Microbial safety of produce from wastewater-fed aquaculture. In: Pullin, R.V.C., Rosenthal, H., MacLean, J.L.(Eds.), Proceedings of ICLARM Conferences, vol. 31, pp. 285-295]. Today, if trade opportunities are to be maintained, these countries must adapt to a full array of regulations and standards. This paper describes four scenarios in aquaculture and fishing product trade between developing countries and countries in the European Union.

  13. Fisheries and aquaculture industries involvement to control product health and quality safety to satisfy consumer-driven objectives on retail markets in Europe

    International Nuclear Information System (INIS)

    Roth, Eva; Rosenthal, Harald

    2006-01-01

    Over the past years the export of agricultural and fishery products from developing countries has substantially increased to markets within the OECD. Retailers and importers are expanding their international operations to meet consumer demands for year-round delivery of products. Moreover, consumers have become increasingly concerned about the safety of food, including those derived from aquatic resources [FAO/NACA/WHO Joint Study Group, 1999. Report food safety issues associated with products from aquaculture. WHO Technical Report Series No 883: VII, pp. 1-55]. Governments and leading businesses are responding by imposing new safety regulations and standards to the international food system (e.g. HACCP, EUREP-GAP), product liability and labeling [Reilly, A., Howgate, P., Kaeferstein, F., 1997. Safety hazards and the application of HACCP in aquaculture. In: Proceedings of the Second International Conference on Fish Inspection and Quality Control: A Global Focus, Arlington, VA, 19-24 May 1996. Technomic Publishing, Lancaster, PA, pp. 353-373]. Initial concerns for imports of aquacultural products from developing to industrialized countries focussed on bacterial contamination [Buras, N. 1993. Microbial safety of produce from wastewater-fed aquaculture. In: Pullin, R.V.C., Rosenthal, H., MacLean, J.L.(Eds.), Proceedings of ICLARM Conferences, vol. 31, pp. 285-295]. Today, if trade opportunities are to be maintained, these countries must adapt to a full array of regulations and standards. This paper describes four scenarios in aquaculture and fishing product trade between developing countries and countries in the European Union

  14. Fisheries and aquaculture industries involvement to control product health and quality safety to satisfy consumer-driven objectives on retail markets in Europe

    Energy Technology Data Exchange (ETDEWEB)

    Roth, Eva [University of South Denmark, Department of Environmental and Business Economics, Niels Bohrs vej 9, DK-6700 Esbjerg (Denmark); Institute for Marine Research, University Kiel, Duesternbrooker Weg 20, 24105 Kiel (Germany); Rosenthal, Harald [University of South Denmark, Department of Environmental and Business Economics, Niels Bohrs vej 9, DK-6700 Esbjerg (Denmark); Institute for Marine Research, University Kiel, Duesternbrooker Weg 20, 24105 Kiel (Germany)

    2006-07-01

    Over the past years the export of agricultural and fishery products from developing countries has substantially increased to markets within the OECD. Retailers and importers are expanding their international operations to meet consumer demands for year-round delivery of products. Moreover, consumers have become increasingly concerned about the safety of food, including those derived from aquatic resources [FAO/NACA/WHO Joint Study Group, 1999. Report food safety issues associated with products from aquaculture. WHO Technical Report Series No 883: VII, pp. 1-55]. Governments and leading businesses are responding by imposing new safety regulations and standards to the international food system (e.g. HACCP, EUREP-GAP), product liability and labeling [Reilly, A., Howgate, P., Kaeferstein, F., 1997. Safety hazards and the application of HACCP in aquaculture. In: Proceedings of the Second International Conference on Fish Inspection and Quality Control: A Global Focus, Arlington, VA, 19-24 May 1996. Technomic Publishing, Lancaster, PA, pp. 353-373]. Initial concerns for imports of aquacultural products from developing to industrialized countries focussed on bacterial contamination [Buras, N. 1993. Microbial safety of produce from wastewater-fed aquaculture. In: Pullin, R.V.C., Rosenthal, H., MacLean, J.L.(Eds.), Proceedings of ICLARM Conferences, vol. 31, pp. 285-295]. Today, if trade opportunities are to be maintained, these countries must adapt to a full array of regulations and standards. This paper describes four scenarios in aquaculture and fishing product trade between developing countries and countries in the European Union.

  15. [Quality process control system of Chinese medicine preparation based on "holistic view"].

    Science.gov (United States)

    Wang, Ya-Qi; Jiao, Jiao-Jiao; Wu, Zhen-Feng; Zheng, Qin; Yang, Ming

    2018-01-01

    "High quality, safety and effectiveness" are the primary principles for the pharmaceutical research and development process in China. The quality of products relies not only on the inspection method, but also on the design and development, process control and standardized management. The quality depends on the process control level. In this paper, the history and current development of quality control of traditional Chinese medicine (TCM) preparations are reviewed systematically. Based on the development model of international drug quality control and the misunderstanding of quality control of TCM preparations, the reasons for impacting the homogeneity of TCM preparations are analyzed and summarized. According to TCM characteristics, efforts were made to control the diversity of TCM, make "unstable" TCM into "stable" Chinese patent medicines, put forward the concepts of "holistic view" and "QbD (quality by design)", so as to create the "holistic, modular, data, standardized" model as the core of TCM preparation quality process control model. Scientific studies shall conform to the actual production of TCM preparations, and be conducive to supporting advanced equipment and technology upgrade, thoroughly applying the scientific research achievements in Chinese patent medicines, and promoting the cluster application and transformation application of TCM pharmaceutical technology, so as to improve the quality and effectiveness of the TCM industry and realize the green development. Copyright© by the Chinese Pharmaceutical Association.

  16. A Scholarly Pathway in Quality Improvement and Patient Safety.

    Science.gov (United States)

    Ferguson, Catherine C; Lamb, Geoffrey

    2015-10-01

    There are several challenges to teaching quality improvement (QI) and patient safety material to medical students, as successful programs should combine didactic and experiential teaching methods, integrate the material into the preclinical and clinical years, and tailor the material to the schools' existing curriculum. The authors describe the development, implementation, and assessment of the Quality Improvement and Patient Safety (QuIPS) Scholarly Pathway-a faculty-mentored, three-year experience for students interested in gaining exposure to QI and patient safety concepts at the Medical College of Wisconsin (MCW). The QuIPS pathway capitalized on the existing structure of scholarly pathways for MCW medical students, allowing QI and patient safety to be incorporated into the existing curriculum using didactic and experiential instruction and spanning preclinical and clinical education. Student reaction to the QuIPS pathway has been favorable. Preliminary data demonstrate that student knowledge as measured by the Quality Improvement Knowledge Assessment Tool significantly increased after the first year of implementation. A novel curriculum such as the QuIPS pathway provides an important opportunity to develop and test new assessment tools for curricula in systems-based practice and practice-based learning and improvement. The authors also hope that by bringing together local QI and patient safety experts and stakeholders during the curricular development process, they have laid the groundwork for the creation of a more pervasive curriculum that will reach all MCW students in the future. The model may be generalizable to other U.S. medical schools with scholarly pathways as well.

  17. Perinatal staff perceptions of safety and quality in their service.

    Science.gov (United States)

    Sinni, Suzanne V; Wallace, Euan M; Cross, Wendy M

    2014-11-28

    Ensuring safe and appropriate service delivery is central to a high quality maternity service. With this in mind, over recent years much attention has been given to the development of evidence-based clinical guidelines, staff education and risk reporting systems. Less attention has been given to assessing staff perceptions of a service's safety and quality and what factors may influence that. In this study we set out to assess staff perceptions of safety and quality of a maternity service and to explore potential influences on service safety. The study was undertaken within a new low risk metropolitan maternity service in Victoria, Australia with a staffing profile comprising midwives (including students), neonatal nurses, specialist obstetricians, junior medical staff and clerical staff. In depth open-ended interviews using a semi-structured questionnaire were conducted with 23 staff involved in the delivery of perinatal care, including doctors, midwives, nurses, nursing and midwifery students, and clerical staff. Data were analyzed using naturalistic interpretive inquiry to identify emergent themes. Staff unanimously reported that there were robust systems and processes in place to maintain safety and quality. Three major themes were apparent: (1) clinical governance, (2) dominance of midwives, (3) inter-professional relationships. Overall, there was a strong sense that, at least in this midwifery-led service, midwives had the greatest opportunity to be an influence, both positively and negatively, on the safe delivery of perinatal care. The importance of understanding team dynamics, particularly mutual respect, trust and staff cohesion, were identified as key issues for potential future service improvement. Senior staff, particularly midwives and neonatal nurses, play central roles in shaping team behaviors and attitudes that may affect the safety and quality of service delivery. We suggest that strategies targeting senior staff to enhance their performance in

  18. Quality and safety of nuclear plants: the role of the administrative authorities

    International Nuclear Information System (INIS)

    Queniart, D.

    1977-10-01

    After specifying the notions of 'safety' and 'quality', the terms and conditions governing the intervention of the public authorities in the matter of safety of nuclear plants are described: individual permits, the establishing and application of technical rules of a general character, surveillance of the plants. The criteria and regulations guiding the evaluation of safety and quality and, in conclusion, insisting on the necessity for permanent discussions among the various organizations concerned are presented

  19. A comparison of the difference of requirements between functional safety and nuclear safety controllers

    Energy Technology Data Exchange (ETDEWEB)

    Chen, C.K.; Lee, C.L.; Shyu, S.S. [Inst. of Nuclear Energy Research, Taoyuan, Taiwan (China)

    2014-07-01

    In order to establish self-reliant capabilities of nuclear I&C systems in Taiwan, Taiwan's Nuclear I&C System (TNICS) project had been established by Institute of Nuclear Energy Research (INER). A Triple Modular Redundant (TMR) safety controller (SCS-2000) has been completed and gone through the IEC 61508 Safety Integrity Level 3 (SIL3) certification of Functional Safety for industries. Based on the certification processes, the difference of requirements between Functional Safety and Nuclear Safety controllers in term of hardware and software are addressed in this study. Besides, the measures used to determine and verify the reliability of the safety control system design are presented. (author)

  20. Role of quality assurance in reactor safety

    International Nuclear Information System (INIS)

    Roedel, J.A.

    1975-01-01

    A quality assurance program based on common sense, designed to accomplish what is reasonable and necessary, giving proper consideration to safety and economics can be an effective and essential management tool for the design, construction and operation of safe and economical nuclear power plants

  1. Quality control and quality standards for the production of bone allografts in China

    International Nuclear Information System (INIS)

    Sun Shiquan; Li Youchen

    1999-01-01

    There is a rapid progress of tissue banking especially Bone Banking in China, In order to strengthen the control on medical devices, Ministry of Public Health (MPH) issued the 'Regulation on Supervision of Critical Medical Devices, MPH Decree No. 54' in 1997. The SPTB was requested to submit new application for the approval of production and providing of tissue allografts. The needed documents are clinical reports, package insert, quality standards of product, Quality System Regulation (QSR) and audit report. Quality System Regulation document adopted the GMP standard for medical devices of FDA, US (21 CFR 620-1997). SPTB will amend the existed Quality Manual to suit the requirement of QSR. Referring to the AATB Standards, SPTB established 'Technical Standards' for Tissue Banking and was approved by the local government, which will be the supplement of the submitted QSR document. Considering the need of market control, MPH requested to submit a 'Quality Standard of Product' and the method of inspection. SPTB has completed such standards for final inspection of bone products, which includes the test for residual water, microbiology, bone species, colour and structure. In addition, the Tissue Bank has completed standards for in process inspection, which includes residual blood, radiation sterilization, initial bioburden, package leakage and biomechanics. In-process inspection is important for the control of non-conforming final products to assure the safety and efficacy of bone grafts. Methods of in process inspection and final inspection are described and discussed in this paper

  2. Safety critical application of fuzzy control

    International Nuclear Information System (INIS)

    Schildt, G.H.

    1995-01-01

    After an introduction into safety terms a short description of fuzzy logic will be given. Especially, for safety critical applications of fuzzy controllers a possible controller structure will be described. The following items will be discussed: Configuration of fuzzy controllers, design aspects like fuzzfiication, inference strategies, defuzzification and types of membership functions. As an example a typical fuzzy rule set will be presented. Especially, real-time behaviour a fuzzy controllers is mentioned. An example of fuzzy controlling for temperature control purpose within a nuclear reactor together with membership functions and inference strategy of such a fuzzy controller will be presented. (author). 4 refs, 17 figs

  3. Understanding the role of sleep quality and sleep duration in commercial driving safety.

    Science.gov (United States)

    Lemke, Michael K; Apostolopoulos, Yorghos; Hege, Adam; Sönmez, Sevil; Wideman, Laurie

    2016-12-01

    Long-haul truck drivers in the United States suffer disproportionately high injury rates. Sleep is a critical factor in these outcomes, contributing to fatigue and degrading multiple aspects of safety-relevant performance. Both sleep duration and sleep quality are often compromised among truck drivers; however, much of the efforts to combat fatigue focus on sleep duration rather than sleep quality. Thus, the current study has two objectives: (1) to determine the degree to which sleep impacts safety-relevant performance among long-haul truck drivers; and (2) to evaluate workday and non-workday sleep quality and duration as predictors of drivers' safety-relevant performance. A non-experimental, descriptive, cross-sectional design was employed to collect survey and biometric data from 260 long-haul truck drivers. The Trucker Sleep Disorders Survey was developed to assess sleep duration and quality, the impact of sleep on job performance and accident risk, and other relevant work organization characteristics. Descriptive statistics assessed work organization variables, sleep duration and quality, and frequency of engaging in safety-relevant performance while sleepy. Linear regression analyses were conducted to evaluate relationships between sleep duration, sleep quality, and work organization variables with safety composite variables. Drivers reported long work hours, with over 70% of drivers working more than 11h daily. Drivers also reported a large number of miles driven per week, with an average of 2,812.61 miles per week, and frequent violations of hours-of-service rules, with 43.8% of drivers "sometimes to always" violating the "14-h rule." Sleep duration was longer, and sleep quality was better, on non-workdays compared on workdays. Drivers frequently operated motor vehicles while sleepy, and sleepiness impacted several aspects of safety-relevant performance. Sleep quality was better associated with driving while sleepy and with job performance and concentration

  4. The level of perceived quality and safety of health services by recipients. Recommendations and inter- ventions for health care policies

    Directory of Open Access Journals (Sweden)

    Foteini Koulouri

    2017-06-01

    Full Text Available In recent years, the importance of the quality in health sector is more and more acknowledged. In broader terms the literature on quality in health care contributed to this, and stressed the importance of meeting the needs of the service recipient. Safety and quality in health care constitute a multi-dimensional parameter and involve many factors and various resources. Safety is positively associated to the quality, as the existence of the one ensures the improvement of the other. Thus, there is a great effort to create a framework, through guidelines and instructions that could contribute to the protection and development of quality and safety. It is important that this framework includes many features that have been expressed as requests by the patients themselves and which can contribute to the development of realistic and effective recommendations for improvement. Greek reality reveals certain gaps in safety and quality of services delivered, so the main attention has to be focused on developing an integral national health policy; the development of guidelines and the appropriate evaluation of their implementation could be a first effective approach. Formulating an institutional framework about safety and quality in health sector should be incorporated in the culture of all health organizations. To this end, the involvement of health professionals is a vital and strategic point. Health care practitioners should incorporate safety and quality culture in their daily routine and health managers should enact efficient ways of evaluation and control mechanisms in order to achieve better outcomes. Motivation to this direction and active participation should be encouraged with positive approaches, away from any kind of sanction. Any mistakes, adverse effects and deviations should be identified, reported, analyzed and formulate the base of the corrective action. In conclusion, safety and quality in health sector are essential and strongly associated

  5. FURNAS activities in safety and quality assurance

    International Nuclear Information System (INIS)

    Dezordi, W.L.; Correa Filho, S.M.; Sacco, W.; Morais, L.H.G. de

    1980-01-01

    The aspects involved in the quality assurance performed by FURNAS for Nuclear Power Plant - Angra Unit I, are shown. Furnas' responsabilities in the licensing regarding reactor safety are also discussed. A summary of the computer codes used in the licensing process is given. (e.G.) [pt

  6. A Comparative Study of Natural Antimicrobial Delivery Systems for Microbial Safety and Quality of Fresh-Cut Lettuce.

    Science.gov (United States)

    Hill, Laura E; Oliveira, Daniela A; Hills, Katherine; Giacobassi, Cassie; Johnson, Jecori; Summerlin, Harvey; Taylor, T Matthew; Gomes, Carmen L

    2017-05-01

    Nanoencapsulation can provide a means to effectively deliver antimicrobial compounds and enhance the safety of fresh produce. However, to date there are no studies which directly compares how different nanoencapsulation systems affect fresh produce safety and quality. This study compared the effects on quality and safety of fresh-cut lettuce treated with free and nanoencapsulated natural antimicrobial, cinnamon bark extract (CBE). A challenge study compared antimicrobial efficacy of 3 different nanoencapsulated CBE systems. The most effective antimicrobial treatment against Listeria monocytogenes was chitosan-co-poly-N-isopropylacrylamide (chitosan-PNIPAAM) encapsulated CBE, with a reduction on bacterial load up to 2 log 10 CFU/g (P lettuce was stored at 5 °C and 10 °C for 15 d. Subsequently, chitosan-PNIPAAM-CBE nanoparticles (20, 40, and 80 mg/mL) were compared to a control and free CBE (400, 800, and 1600 μg/mL) for its effects on fresh-cut lettuce quality over 15 d at 5 °C. By the 10th day, the most effective antimicrobial concentration was 80 mg/mL for chitosan-PNIPAAM-CBE, up to 2 log 10 CFU/g reduction (P lettuce shelf-life. Overall, nanoencapsulation provided a method to effectively deliver essential oil and enhanced produce safety, while creating little to no detrimental quality changes on the fresh-cut lettuce. © 2017 Institute of Food Technologists®.

  7. 30 CFR 250.806 - Safety and pollution prevention equipment quality assurance requirements.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Safety and pollution prevention equipment... Gas Production Safety Systems § 250.806 Safety and pollution prevention equipment quality assurance... install only certified safety and pollution prevention equipment (SPPE) in wells located on the OCS. SPPE...

  8. Circles of quality in radiological safety

    International Nuclear Information System (INIS)

    Gonzalez F, J.A.

    1991-01-01

    The concept of Circles of quality arose in Japan like an option to capitalize the enormous potential that the workers had developed as a result of its training in the statistical tools of quality. There are presented a series of steps that could be given with the purpose of implementing a program of ALARA circles. The radiological safety is in it finishes instance responsibility of each hard-working one and there won't be a protection program that can work among apathetic people, it is in this sense where the ALARA circles can provide its maximum contribution creating a conscience of responsibility and participation

  9. Journey Toward High Reliability: A Comprehensive Safety Program to Improve Quality of Care and Safety Culture in a Large, Multisite Radiation Oncology Department.

    Science.gov (United States)

    Woodhouse, Kristina Demas; Volz, Edna; Maity, Amit; Gabriel, Peter E; Solberg, Timothy D; Bergendahl, Howard W; Hahn, Stephen M

    2016-05-01

    High-reliability organizations (HROs) focus on continuous identification and improvement of safety issues. We sought to advance a large, multisite radiation oncology department toward high reliability through the implementation of a comprehensive safety culture (SC) program at the University of Pennsylvania Department of Radiation Oncology. In 2011, with guidance from safety literature and experts in HROs, we designed an SC framework to reduce radiation errors. All state-reported medical events (SRMEs) from 2009 to 2016 were retrospectively reviewed and plotted on a control chart. Changes in SC grade were assessed using the Agency for Healthcare Research and Quality Hospital Survey. Outcomes measured included the number of radiation treatment fractions and days between SRMEs, as well as SC grade. Multifaceted safety initiatives were implemented at our main academic center and across all network sites. Postintervention results demonstrate increased staff fundamental safety knowledge, enhanced peer review with an electronic system, and special cause variation of SRMEs on control chart analysis. From 2009 to 2016, the number of days and fractions between SRMEs significantly increased, from a mean of 174 to 541 days (P safety framework. Our multifaceted initiatives, focusing on culture and system changes, can be successfully implemented in a large academic radiation oncology department to yield measurable improvements in SC and outcomes. Copyright © 2016 by American Society of Clinical Oncology.

  10. Transformational Leadership: The Chief Nursing Officer Role in Leading Quality and Patient Safety.

    Science.gov (United States)

    Jones, Pam; Polancich, Shea; Steaban, Robin; Feistritzer, Nancye; Poe, Terri

    This department column highlights leadership perspectives of quality and patient safety practice. The purpose of this article is to provide strategic direction for transformational quality and safety leadership as the chief nursing officer (CNO) within the academic medical center environment.

  11. Examining quality function deployment in safety promotion in Sweden.

    Science.gov (United States)

    Kullberg, Agneta; Nordqvist, Cecilia; Lindqvist, Kent; Timpka, Toomas

    2014-09-01

    The first-hand needs and demands of laypersons are not always considered when safety promotion programmes are being developed. We compared focal areas for interventions identified from residents' statements of safety needs with focal areas for interventions identified by local government professionals in a Swedish urban community certified by the international Safe Community movement supported by the World Health Organization. Quantitative and qualitative data on self-expressed safety needs from 787 housing residents were transformed into an intervention design, using the quality function deployment (QFD) technique and compared with the safety intervention programme developed by professionals at the municipality administrative office. The outcome of the comparison was investigated with regard to implications for the Safe Community movement. The QFD analysis identified the initiation and maintenance of social integrative processes in housing areas as the most highly prioritized interventions among the residents, but failed to highlight the safety needs of several vulnerable groups (the elderly, infants and persons with disabilities). The intervention programme designed by the public health professionals did not address the social integrative processes, but it did highlight the vulnerable groups. This study indicates that the QFD technique is suitable for providing residential safety promotion efforts with a quality orientation from the layperson's perspective. Views of public health professionals have to be included to ascertain that the needs of socially deprived residents are adequately taken into account. QFD can augment the methodological toolbox for safety promotion programmes, including interventions in residential areas. © The Author (2013). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  12. Results of pilot project on introducing quality control of mammographic equipment

    International Nuclear Information System (INIS)

    Vasileva, Zh.; Lichev, A.; Dimov, A.; Kostova, E.; Dimov, G.

    2003-01-01

    Objective:The results from a pilot project, realized in the framework of the PHARE Project 'Radiation Protection and Safety in Medical Use of the Ionizing Radiation'. The main goal of the project is the elaboration a quality control program for mammographic equipment and its implementation in 4 radiological units in the country. Another task is to examine the possibility for conducting a mammographic screening using this equipment. Material and methods: The developed quality control program has the following components: test parameters; criteria for intervention; minimal frequency of measurement. Methodologies for measurement of the parameters and assessment of the results in accordance with the European Protocol for physical and technical aspects of the mammographic screening. Standard protocols have been elaborated. Results: The quality program has been tested for three month at different hospitals. Conclusions: Optimization and strict control of the process of film development are needed. The exposure equipment. The quality control program should be implemented on all mammographic equipment in the country. For the performance of mammographic screening a strict selection of the equipment is necessary

  13. Financial Control and Safety. An investigation on how financial and safety aspects are integrated in the decision making at the Swedish nuclear power plants; Ekonomistyrning och saekerhet. En utredning om hur ekonomi- och saekerhetsaspekter integreras vid beslutsfattandet vid kaernkraftverken

    Energy Technology Data Exchange (ETDEWEB)

    Vaernild, Ola [OV Konsult i Vaesteraas AB, Vaesteraas (Sweden)

    2005-08-01

    The alleged inter-relationship between economy and nuclear safety has been investigated. Through interviews and review of instructions and other documents, information on how management at Swedish nuclear power plants integrates financial control and safety management has been compiled. Owners of nuclear power plants have well founded expectations on that the plants are profitable and that the operations are rationalized in order to reduce costs. This could allegedly threaten the nuclear safety. However, it is not to be expected that there are any obvious relationships between expenditures and safety. The quality of the safety management has to be judged in terms of how well safety requirements are met irrespective of the associated costs. The owners have imposed clear financial objectives on the nuclear power plants. At the same time they have also established policies for nuclear safety. The nuclear power plants have systems for operations management, which basically comprise separate parts for operations planning and quality management. Financial control and safety management are included in the operations planning and quality management respectively. The quality management impose restrictions to be adhered to in the operations planning. This means that from a formal point of view, the safety management is superior to the operations planning. There are examples of simple as well as advanced approaches to financial management at the nuclear power plants. In all cases the methods used are reasonably well adapted to the needs. Typical for all plants is the focus on long-term aspects. Investments are for example analysed in a plant life-time perspective. With regard to safety, profitability calculations are not required to the same extent for safety related investments as for other investments. A number of factors, which tend to warrant that safety aspects are given the appropriate attention in the decision making, have been identified. Examples of such factors are

  14. Configuration control during maintenance of safety related equipment

    International Nuclear Information System (INIS)

    Irish, C.S.

    2001-01-01

    Possibly the most important aspect of performing maintenance of safety related equipment is maintaining the component's original design basis. Assuring that the repaired item will perform the same safety function within the original performance and equipment qualification parameters is commonly referred to as configuration control. Maintaining configuration control of a technologically current well documented item is easy. Unfortunately, this does not describe most safety related items requiring maintenance within the global nuclear industry. Items such as motors, transformers, metal clad switchgear (low and medium voltage circuit breakers), refrigeration compressors, and electronic components (i.e. circuit boards, power supplies, regulators, etc.) which routinely require repair have been in service for twenty plus years. As a result, finding replacement parts and or material to repair the items to the original condition is becoming more and more difficult. An added difficulty is the lack of original technical documentation available on the item which is being repaired. The lack of technical documentation makes it difficult to identify replacement material and parts when the original part or material is not available. The lack of documentation also makes it difficult to test the repaired item to make sure that the original configuration has been maintained after the repair. The presentation will discuss the details of repairing various items including motors, metal clad switchgear, refrigeration compressors and power supplies and the controls which are necessary to maintain the configuration of the original item. The discussion will include the Quality Assurance and engineering necessary to identify and evaluate replacement material and parts necessary to perform repairs on safety related equipment when the original material or part is not available. Examples of repairs which required different parts or materials than the original to be used in the repair will be

  15. Configuration control during maintenance of safety related equipment

    International Nuclear Information System (INIS)

    Irish, C.S.

    2003-01-01

    Possibly the most important aspect of performing maintenance of safety related equipment is maintaining the component's original design basis. Assuring that the repaired item will perform the same safety function within the original performance and equipment qualification parameters is commonly referred to as configuration control. Maintaining configuration control of a technologically current well documented item is easy. Unfortunately, this does not describe most safety related items requiring maintenance within the global nuclear industry. Items such as motors, transformers, metal clad switchgear (low and medium voltage circuit breakers), refrigeration compressors, and electronic components (i.e. circuit boards, power supplies, regulators, etc.) which routinely require repair have been in service for twenty plus years. As a result, finding replacement parts and or material to repair the items to the original condition is becoming more and more difficult. An added difficulty is the lack of original technical documentation available on the item which is being repaired. The lack of technical documentation makes it difficult to identify replacement material and parts when the original part or material is not available. The lack of documentation also makes it difficult to test the repaired item to make sure that the original configuration has been maintained after the repair. The presentation will discuss the details of repairing various items including motors, metal clad switchgear, refrigeration compressors and power supplies and the controls which are necessary to maintain the configuration of the original item. The discussion will include the Quality Assurance and engineering necessary to identify and evaluate replacement material and parts necessary to perform repairs on safety related equipment when the original material or part is not available. Examples of repairs which required different parts or materials than the original to be used in the repair will be

  16. Job Demands-Control-Support model and employee safety performance.

    Science.gov (United States)

    Turner, Nick; Stride, Chris B; Carter, Angela J; McCaughey, Deirdre; Carroll, Anthony E

    2012-03-01

    The aim of this study was to explore whether work characteristics (job demands, job control, social support) comprising Karasek and Theorell's (1990) Job Demands-Control-Support framework predict employee safety performance (safety compliance and safety participation; Neal and Griffin, 2006). We used cross-sectional data of self-reported work characteristics and employee safety performance from 280 healthcare staff (doctors, nurses, and administrative staff) from Emergency Departments of seven hospitals in the United Kingdom. We analyzed these data using a structural equation model that simultaneously regressed safety compliance and safety participation on the main effects of each of the aforementioned work characteristics, their two-way interactions, and the three-way interaction among them, while controlling for demographic, occupational, and organizational characteristics. Social support was positively related to safety compliance, and both job control and the two-way interaction between job control and social support were positively related to safety participation. How work design is related to employee safety performance remains an important area for research and provides insight into how organizations can improve workplace safety. The current findings emphasize the importance of the co-worker in promoting both safety compliance and safety participation. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

  17. Safety critical FPGA-based NPP instrumentation and control systems: assessment, development and implementation

    Energy Technology Data Exchange (ETDEWEB)

    Bakhmach, E. S.; Siora, A. A.; Tokarev, V. I. [Research and Production Corporation Radiy, 29 Geroev Stalingrada Str., Kirovograd 25006 (Ukraine); Kharchenko, V. S.; Sklyar, V. V.; Andrashov, A. A., E-mail: marketing@radiy.co [Center for Safety Infrastructure-Oriented Research and Analysis, 37 Astronomicheskaya Str., Kharkiv 61085 (Ukraine)

    2010-10-15

    The stages of development, production, verification, licensing and implementation methods and technologies of safety critical instrumentation and control systems for nuclear power plants (NPP) based on FPGA (Field Programmable Gates Arrays) technologies are described. A life cycle model and multi-version technologies of dependability and safety assurance of FPGA-based instrumentation and control systems are discussed. An analysis of NPP instrumentation and control systems construction principles developed by Research and Production Corporation Radiy using FPGA-technologies and results of these systems implementation and operation at Ukrainian and Bulgarian NPP are presented. The RADIY{sup TM} platform has been designed and developed by Research and Production Corporation Radiy, Ukraine. The main peculiarity of the RADIY{sup TM} platform is the use of FPGA as programmable components for logic control operation. The FPGA-based RADIY{sup TM} platform used for NPP instrumentation and control systems development ensures sca lability of system functions types, volume and peculiarities (by changing quantity and quality of sensors, actuators, input/output signals and control algorithms); sca lability of dependability (safety integrity) (by changing a number of redundant channel, tiers, diagnostic and reconfiguration procedures); sca lability of diversity (by changing types, depth and method of diversity selection). (Author)

  18. The Armstrong Institute: An Academic Institute for Patient Safety and Quality Improvement, Research, Training, and Practice.

    Science.gov (United States)

    Pronovost, Peter J; Holzmueller, Christine G; Molello, Nancy E; Paine, Lori; Winner, Laura; Marsteller, Jill A; Berenholtz, Sean M; Aboumatar, Hanan J; Demski, Renee; Armstrong, C Michael

    2015-10-01

    Academic medical centers (AMCs) could advance the science of health care delivery, improve patient safety and quality improvement, and enhance value, but many centers have fragmented efforts with little accountability. Johns Hopkins Medicine, the AMC under which the Johns Hopkins University School of Medicine and the Johns Hopkins Health System are organized, experienced similar challenges, with operational patient safety and quality leadership separate from safety and quality-related research efforts. To unite efforts and establish accountability, the Armstrong Institute for Patient Safety and Quality was created in 2011.The authors describe the development, purpose, governance, function, and challenges of the institute to help other AMCs replicate it and accelerate safety and quality improvement. The purpose is to partner with patients, their loved ones, and all interested parties to end preventable harm, continuously improve patient outcomes and experience, and eliminate waste in health care. A governance structure was created, with care mapped into seven categories, to oversee the quality and safety of all patients treated at a Johns Hopkins Medicine entity. The governance has a Patient Safety and Quality Board Committee that sets strategic goals, and the institute communicates these goals throughout the health system and supports personnel in meeting these goals. The institute is organized into 13 functional councils reflecting their behaviors and purpose. The institute works daily to build the capacity of clinicians trained in safety and quality through established programs, advance improvement science, and implement and evaluate interventions to improve the quality of care and safety of patients.

  19. Effect of Storage on the Quality and Safety of Grains in Tharaka ...

    African Journals Online (AJOL)

    The contribution of grains to food security is limited by deterioration during storage and as such it was necessary to document the effect of storage on their quality and safety. The objective of this study was to determine the effect of storage on the quality and safety of grains in Maragua and Gikingo locations, Tharaka District, ...

  20. One complex tool and three simple approaches to the improvement of quality assurance and safety in external beam radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Salinas, F.; Sansogne, R.; Arbiser, S.; Suarez, V., E-mail: flavio.salinas@rtp.com.ar [Vidt Centro Medico (Argentina); Franco, M., E-mail: mauricio.franco@rtp.com.ar [Centro de Radioterapia San Juan (Argentina); Escobar, J., E-mail: jorge.escobar@iprc.com.ar [Instituto Privado de Radioterapia Cuyo, Buenos Aires (Argentina)

    2013-10-01

    Quality assurance and safety controls in radiation therapy delivery processes that involve the Physics Department of an institution are commonly time consuming tasks. Carrying out daily controls in very busy clinics without compromising patient schedule is challenging. This work describes the usage of Electronic Portal Imaging Devices in combination with some in-house software to simplify and systematize three different tasks of the Physics Department Quality Assurance Program, improving the easiness, reliability and velocity of daily tests. (author)

  1. One complex tool and three simple approaches to the improvement of quality assurance and safety in external beam radiotherapy

    International Nuclear Information System (INIS)

    Salinas, F.; Sansogne, R.; Arbiser, S.; Suarez, V.; Franco, M.; Escobar, J.

    2013-01-01

    Quality assurance and safety controls in radiation therapy delivery processes that involve the Physics Department of an institution are commonly time consuming tasks. Carrying out daily controls in very busy clinics without compromising patient schedule is challenging. This work describes the usage of Electronic Portal Imaging Devices in combination with some in-house software to simplify and systematize three different tasks of the Physics Department Quality Assurance Program, improving the easiness, reliability and velocity of daily tests. (author)

  2. Modern control system of quality of services of public catering

    Directory of Open Access Journals (Sweden)

    Lavrova Larisa Jur'evna

    2015-12-01

    Full Text Available The modern control system of quality of services of public catering as the instrument of management of safety is effective and legitimate. In article changes in requirements of normative documents are considered. Interdisciplinary mechanisms of implementation of requirements of normative documents are described. Uniform approaches between marketing and quality management regarding monitoring of satisfaction of consumers are determined. Results of researches of the organization of collection of information about degree of satisfaction of consumers are described. Knowledge, necessary for the staff of catering establishments, and skills regarding development, introduction and maintenance of quality management system in activity of the enterprises of food are established.

  3. Quality Management, Quality Assurance and Quality Control in Blood Establishments

    OpenAIRE

    Bolbate, N

    2008-01-01

    Quality terms and the roots of the matter are analyzed according to European Committee’s recommendations. Essence of process and product quality control as well as essence of quality assurance is described. Quality system’s structure including quality control, quality assurance and management is justified in the article.

  4. Caregivers’ Use of Child Passenger Safety Resources and Quality of Future Child Restraint System Installations

    Directory of Open Access Journals (Sweden)

    Jessica H. Mirman

    2017-10-01

    Full Text Available Objectives: Child Restraint System (CRS misuse is common. We characterized caregivers’ use of child passenger safety informational and instructional resources and determined whether there were differences in the quality of CRS installations associated with prior exposure to specific resources as evaluated in a standardized CRS installation environment. Methods: Caregivers completed self-report surveys and installed a forward-facing CRS in a controlled environment. Installations were evaluated for security (tightness and accuracy (no errors by a child passenger safety technician (CPST. Results: CRS manuals were the most common way caregivers learned to install a CRS. Primary care providers (PCPs were the most frequently endorsed source of CRS safety information. There was no strong pattern of associations between prior exposure to resources and installation quality (security or accuracy, although some evidence supports protective effects of learning from CPSTs; 13% (19 out of 151 installations were secure and 57% (86 out of 151 installations were accurate. Conclusions: A focus on developing effective and lasting behavioral interventions is needed.

  5. Ten years after the IOM report: Engaging residents in quality and patient safety by creating a House Staff Quality Council.

    Science.gov (United States)

    Fleischut, Peter M; Evans, Adam S; Nugent, William C; Faggiani, Susan L; Lazar, Eliot J; Liebowitz, Richard S; Forese, Laura L; Kerr, Gregory E

    2011-01-01

    Ten years after the 1999 Institute of Medicine report, it is clear that despite significant progress, much remains to be done to improve quality and patient safety (QPS). Recognizing the critical role of postgraduate trainees, an innovative approach was developed at New York-Presbyterian Hospital, Weill Cornell Medical Center to engage residents in QPS by creating a Housestaff Quality Council (HQC). HQC leaders and representatives from each clinical department communicate and partner regularly with hospital administration and other key departments to address interdisciplinary quality improvement (QI). In support of the mission to improve patient care and safety, QI initiatives included attaining greater than 90% compliance with medication reconciliation and reduction in the use of paper laboratory orders by more than 70%. A patient safety awareness campaign is expected to evolve into a transparent environment where house staff can openly discuss patient safety issues to improve the quality of care.

  6. Use of irradiation to improve the safety and quality of Thai prepared meal

    Energy Technology Data Exchange (ETDEWEB)

    Noomhorm, A [Food Engineering and Bioprocess Technology, Asian Institute of Technology (Thailand)

    2002-07-01

    There is a dynamic growth of market for chilled prepared meals in Thailand because of the growth of food services in supermarkets and convenient stores. However, the shelf life of this food is short furthermore it is implicated in a number of serious foodborne disease outbreaks. Irradiation could provide a potential to improve the microbiological safety and extend the shelf life of chilled prepared meals. It is possibly used alone or together with chilling. With the combination of irradiation and chilling, frozen condition could be replaced resulting to saving in energy and cost. However, there is a limitation of information about the application of irradiation on chilled prepared meals. Also, information relevant to the application of food safety control system like Hazard Analysis and Critical Control Point (HACCP) should be gathered to ensure more safety of the irradiated prepared meals. For Thai dishes, they are normally composed of herb and spicy with different types of meat. All dishes are eaten along with rice. Both Thai aromatic rice and herb are susceptible to deterioration in quality by processing factors. Therefore, the study of the effect of irradiation on Thai dishes, which compose of these two components, is necessary.

  7. Spallation Neutron Source Accelerator Facility Target Safety and Non-safety Control Systems

    International Nuclear Information System (INIS)

    Battle, Ronald E.; DeVan, B.; Munro, John K. Jr.

    2006-01-01

    The Spallation Neutron Source (SNS) is a proton accelerator facility that generates neutrons for scientific researchers by spallation of neutrons from a mercury target. The SNS became operational on April 28, 2006, with first beam on target at approximately 200 W. The SNS accelerator, target, and conventional facilities controls are integrated by standardized hardware and software throughout the facility and were designed and fabricated to SNS conventions to ensure compatibility of systems with Experimental Physics Integrated Control System (EPICS). ControlLogix Programmable Logic Controllers (PLCs) interface to instruments and actuators, and EPICS performs the high-level integration of the PLCs such that all operator control can be accomplished from the Central Control room using EPICS graphical screens that pass process variables to and from the PLCs. Three active safety systems were designed to industry standards ISA S84.01 and IEEE 603 to meet the desired reliability for these safety systems. The safety systems protect facility workers and the environment from mercury vapor, mercury radiation, and proton beam radiation. The facility operators operated many of the systems prior to beam on target and developed the operating procedures. The safety and non-safety control systems were tested extensively prior to beam on target. This testing was crucial to identify wiring and software errors and failed components, the result of which was few problems during operation with beam on target. The SNS has continued beam on target since April to increase beam power, check out the scientific instruments, and continue testing the operation of facility subsystems

  8. Tank safety screening data quality objective. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, J.W.

    1995-04-27

    The Tank Safety Screening Data Quality Objective (DQO) will be used to classify 149 single shell tanks and 28 double shell tanks containing high-level radioactive waste into safety categories for safety issues dealing with the presence of ferrocyanide, organics, flammable gases, and criticality. Decision rules used to classify a tank as ``safe`` or ``not safe`` are presented. Primary and secondary decision variables used for safety status classification are discussed. The number and type of samples required are presented. A tabular identification of each analyte to be measured to support the safety classification, the analytical method to be used, the type of sample, the decision threshold for each analyte that would, if violated, place the tank on the safety issue watch list, and the assumed (desired) analytical uncertainty are provided. This is a living document that should be evaluated for updates on a semiannual basis. Evaluation areas consist of: identification of tanks that have been added or deleted from the specific safety issue watch lists, changes in primary and secondary decision variables, changes in decision rules used for the safety status classification, and changes in analytical requirements. This document directly supports all safety issue specific DQOs and additional characterization DQO efforts associated with pretreatment and retrieval. Additionally, information obtained during implementation can assist in resolving assumptions for revised safety strategies, and in addition, obtaining information which will support the determination of error tolerances, confidence levels, and optimization schemes for later revised safety strategy documentation.

  9. Anesthesia Quality and Patient Safety in China: A Survey.

    Science.gov (United States)

    Zhu, Bin; Gao, Huan; Zhou, Xiangyong; Huang, Jeffrey

    There has been no nationwide investigation into anesthesia quality and patient safety in China. The authors surveyed Chinese anesthesiologists about anesthesia quality by sending a survey to all anesthesiologist members of the New Youth Anesthesia Forum via WeChat. The respondents could choose to use a mobile device or desktop to complete the survey. The overall response rate was 43%. Intraoperative monitoring: 77.9% of respondents reported that electrocardiogram monitoring was routinely applied for all patients; only 55% of the respondents reported that they routinely used end-tidal carbon dioxide monitoring for their patients under general anesthesia. 10.3% of respondents admitted that they had at least one wrong medicine administration in the past 3 months; 12.4% reported that they had at least one case of cardiac arrest in the past year. This is the first anesthesia quality survey in China. The findings revealed potential anesthesia safety issues in China.

  10. Improving Employees' Safety Awareness in Healthcare Organizations Using the DMAIC Quality Improvement Approach.

    Science.gov (United States)

    Momani, Amer; Hirzallah, Muʼath; Mumani, Ahmad

    Occupational injuries and illnesses in healthcare can cause great human suffering, incur high cost, and have an adverse impact on the quality of patient care. One of the most effective solutions for addressing health and safety issues and improving decisions at the point of care rests in raising employees' safety awareness to recognize, avoid, or respond to potential problems before they arise. In this article, the DMAIC Six Sigma model (Define, Measure, Analyze, Improve, Control) is used as a systematic program to measure, improve, and sustain employees' safety awareness in healthcare organizations. We report on a case study using the model, which was implemented and validated at a local hospital. First, the occupational health and safety knowledge that each job requires was identified. Next, the degree of competence of jobholders to meet these requirements was assessed. Based on the assessment, different awareness-raising efforts were proposed and implemented. The results showed significant improvement in the overall safety awareness compliance assessed: from 74.2% to 84.4% (p < .001) after the intervention. The proposed model ensures that the organization's awareness-raising efforts serve its actual needs and produce optimized and sustained results that eventually lead to safer healthcare service.

  11. Incorporating Traffic Control and Safety Hardware Performance Functions into Risk-based Highway Safety Analysis

    Directory of Open Access Journals (Sweden)

    Zongzhi Li

    2017-04-01

    Full Text Available Traffic control and safety hardware such as traffic signs, lighting, signals, pavement markings, guardrails, barriers, and crash cushions form an important and inseparable part of highway infrastructure affecting safety performance. Significant progress has been made in recent decades to develop safety performance functions and crash modification factors for site-specific crash predictions. However, the existing models and methods lack rigorous treatments of safety impacts of time-deteriorating conditions of traffic control and safety hardware. This study introduces a refined method for computing the Safety Index (SI as a means of crash predictions for a highway segment that incorporates traffic control and safety hardware performance functions into the analysis. The proposed method is applied in a computation experiment using five-year data on nearly two hundred rural and urban highway segments. The root-mean square error (RMSE, Chi-square, Spearman’s rank correlation, and Mann-Whitney U tests are employed for validation.

  12. Controlled versus automatic processes: which is dominant to safety? The moderating effect of inhibitory control.

    Directory of Open Access Journals (Sweden)

    Yaoshan Xu

    Full Text Available This study explores the precursors of employees' safety behaviors based on a dual-process model, which suggests that human behaviors are determined by both controlled and automatic cognitive processes. Employees' responses to a self-reported survey on safety attitudes capture their controlled cognitive process, while the automatic association concerning safety measured by an Implicit Association Test (IAT reflects employees' automatic cognitive processes about safety. In addition, this study investigates the moderating effects of inhibition on the relationship between self-reported safety attitude and safety behavior, and that between automatic associations towards safety and safety behavior. The results suggest significant main effects of self-reported safety attitude and automatic association on safety behaviors. Further, the interaction between self-reported safety attitude and inhibition and that between automatic association and inhibition each predict unique variances in safety behavior. Specifically, the safety behaviors of employees with lower level of inhibitory control are influenced more by automatic association, whereas those of employees with higher level of inhibitory control are guided more by self-reported safety attitudes. These results suggest that safety behavior is the joint outcome of both controlled and automatic cognitive processes, and the relative importance of these cognitive processes depends on employees' individual differences in inhibitory control. The implications of these findings for theoretical and practical issues are discussed at the end.

  13. Water-safety strategies and local-scale spatial quality

    NARCIS (Netherlands)

    Nillesen, A.L.

    2013-01-01

    Delta regions throughout the world are subject to increasing flood risks. For protection, regional water safety strategies are being developed. Local-scale spatial qualities should be included in their evaluation. An experimental methodology has been developed for this purpose. This paper

  14. [Drinking water quality and safety].

    Science.gov (United States)

    Gómez-Gutiérrez, Anna; Miralles, Maria Josepa; Corbella, Irene; García, Soledad; Navarro, Sonia; Llebaria, Xavier

    2016-11-01

    The purpose of drinking water legislation is to guarantee the quality and safety of water intended for human consumption. In the European Union, Directive 98/83/EC updated the essential and binding quality criteria and standards, incorporated into Spanish national legislation by Royal Decree 140/2003. This article reviews the main characteristics of the aforementioned drinking water legislation and its impact on the improvement of water quality against empirical data from Catalonia. Analytical data reported in the Spanish national information system (SINAC) indicate that water quality in Catalonia has improved in recent years (from 88% of analytical reports in 2004 finding drinking water to be suitable for human consumption, compared to 95% in 2014). The improvement is fundamentally attributed to parameters concerning the organoleptic characteristics of water and parameters related to the monitoring of the drinking water treatment process. Two management experiences concerning compliance with quality standards for trihalomethanes and lead in Barcelona's water supply are also discussed. Finally, this paper presents some challenges that, in the opinion of the authors, still need to be incorporated into drinking water legislation. It is necessary to update Annex I of Directive 98/83/EC to integrate current scientific knowledge, as well as to improve consumer access to water quality data. Furthermore, a need to define common criteria for some non-resolved topics, such as products and materials in contact with drinking water and domestic conditioning equipment, has also been identified. Copyright © 2016 SESPAS. Publicado por Elsevier España, S.L.U. All rights reserved.

  15. Instrumentation and control systems important to safety in nuclear power plants. Safety guide

    International Nuclear Information System (INIS)

    2005-01-01

    This Safety Guide was prepared under the IAEA programme for establishing safety standards for nuclear power plants. It supplements Safety Standards Series No. NS-R-1: Safety of Nuclear Power Plants: Design (the Requirements for Design), which establishes the design requirements for ensuring the safety of nuclear power plants. This Safety Guide describes how the requirements should be met for instrumentation and control (I and C) systems important to safety. This publication is a revision and combination of two previous Safety Guides: Safety Series Nos 50-SG-D3 and 50-SG-D8, which are superseded by this new Safety Guide. The revision takes account of developments in I and C systems important to safety since the earlier Safety Guides were published in 1980 and 1984, respectively. The objective of this Safety Guide is to provide guidance on the design of I and C systems important to safety in nuclear power plants, including all I and C components, from the sensors allocated to the mechanical systems to the actuated equipment, operator interfaces and auxiliary equipment. This Safety Guide deals mainly with design requirements for those I and C systems that are important to safety. It expands on paragraphs of Ref in the area of I and C systems important to safety. This publication is intended for use primarily by designers of nuclear power plants and also by owners and/or operators and regulators of nuclear power plants. This Safety Guide provides general guidance on I and C systems important to safety which is broadly applicable to many nuclear power plants. More detailed requirements and limitations for safe operation specific to a particular plant type should be established as part of the design process. The present guidance is focused on the design principles for systems important to safety that warrant particular attention, and should be applied to both the design of new I and C systems and the modernization of existing systems. Guidance is provided on how design

  16. Development of digital safety system logic and control

    International Nuclear Information System (INIS)

    Nishikawa, H.; Sakamoto, H.

    1995-01-01

    Advanced-BWR (ABWR) uses total digital control and instrumentation (C and I) system. In particular, ABWR adopts a newly developed safety system using advanced digital technology. In the presentation the digital safety system design, manufacturing and factory validation test method are shortly overviewed. The digital safety system consists of micro-processor based digital controllers, data and information transmission by optical fibers and human-machine interface using color flat displays. This new developed safety system meet the nuclear safety requirements such as high reliability, independence of divisions, operability and maintainability. (2 refs., 4 figs., 1 tab.)

  17. An analysis of safety control effectiveness

    International Nuclear Information System (INIS)

    Son, K.S.; Melchers, R.E.; Kal, W.M.

    2000-01-01

    The cost of injuries and 'accidents' to an organisation is very important in establishing how much it should spend on safety control. Despite the usefulness of information about the cost of a company's accidents, it is not customary accounting practice to make these data available. Of the two kinds of costs incurred by a company through occupational injuries and accidents, direct costs and indirect costs; the direct costs are much easier to estimate. However, the uninsured costs are usually more critical and should be estimated by each company. The authors investigate a general model to estimate the above costs and hence to establish efficient safety control. One construction company has been a pilot for this study. By analysing actual company data for three years, it is found that the efficient safety control cost should be 1.2-1.3% of total contract costs

  18. Safety climate and self-reported injury: assessing the mediating role of employee safety control.

    Science.gov (United States)

    Huang, Yueng-Hsiang; Ho, Michael; Smith, Gordon S; Chen, Peter Y

    2006-05-01

    To further reduce injuries in the workplace, companies have begun focusing on organizational factors which may contribute to workplace safety. Safety climate is an organizational factor commonly cited as a predictor of injury occurrence. Characterized by the shared perceptions of employees, safety climate can be viewed as a snapshot of the prevailing state of safety in the organization at a discrete point in time. However, few studies have elaborated plausible mechanisms through which safety climate likely influences injury occurrence. A mediating model is proposed to link safety climate (i.e., management commitment to safety, return-to-work policies, post-injury administration, and safety training) with self-reported injury through employees' perceived control on safety. Factorial evidence substantiated that management commitment to safety, return-to-work policies, post-injury administration, and safety training are important dimensions of safety climate. In addition, the data support that safety climate is a critical factor predicting the history of a self-reported occupational injury, and that employee safety control mediates the relationship between safety climate and occupational injury. These findings highlight the importance of incorporating organizational factors and workers' characteristics in efforts to improve organizational safety performance.

  19. Food safety and quality assurance : foods of animal origin

    National Research Council Canada - National Science Library

    Hughes, Keith L; Hinton, Michael H; Hubbert, William T; Hagstad, Harry V; Spangler, Elizabeth

    1996-01-01

    The second edition of Food Safety and Quality Assurance is a basic reference for veterinarians, extension specialists, and others who help food-animal producers throughout the food chain to provide...

  20. Safety-related control air systems - approved 1977

    International Nuclear Information System (INIS)

    Anon.

    1978-01-01

    This standard applies to those portions of the control air system that furnish air required to support, control, or operate systems or portions of systems that are safety related in nuclear power plants. This standard relates only to the air supply system(s) for safety-related air operated devices and does not apply to the safety-related air operated device or to air operated actuators for such devices. The objectives of this standard are to provide (1) minimum system design requirements for equipment, piping, instruments, controls, and wiring that constitute the air supply system; and (2) the system and component testing and maintenance requirements

  1. The association between event learning and continuous quality improvement programs and culture of patient safety.

    Science.gov (United States)

    Mazur, Lukasz; Chera, Bhishamjit; Mosaly, Prithima; Taylor, Kinley; Tracton, Gregg; Johnson, Kendra; Comitz, Elizabeth; Adams, Robert; Pooya, Pegah; Ivy, Julie; Rockwell, John; Marks, Lawrence B

    2015-01-01

    To present our approach and results from our quality and safety program and to report their possible impact on our culture of patient safety. We created an event learning system (termed a "good catch" program) and encouraged staff to report any quality or safety concerns in real time. Events were analyzed to assess the utility of safety barriers. A formal continuous quality improvement program was created to address these reported events and make improvements. Data on perceptions of the culture of patient safety were collected using the Agency for Health Care Research and Quality survey administered before, during, and after the initiatives. Of 560 good catches reported, 367 could be ascribed to a specific step on our process map. The calculated utility of safety barriers was highest for those embedded into the pretreatment quality assurance checks performed by physicists and dosimetrists (utility score 0.53; 93 of 174) and routine checks done by therapists on the initial day of therapy. Therapists and physicists reported the highest number of good catches (24% each). Sixty-four percent of events were caused by performance issues (eg, not following standardized processes, including suboptimal communications). Of 31 initiated formal improvement events, 26 were successfully implemented and sustained, 4 were discontinued, and 1 was not implemented. Most of the continuous quality improvement program was conducted by nurses (14) and therapists (7). Percentages of positive responses in the patient safety culture survey appear to have increased on all dimensions (p continuous quality improvement programs can be successfully implemented and that there are contemporaneous improvements in the culture of safety. Copyright © 2015 American Society for Radiation Oncology. Published by Elsevier Inc. All rights reserved.

  2. TH-E-19A-01: Quality and Safety in Radiation Therapy

    Energy Technology Data Exchange (ETDEWEB)

    Ford, E [University of Washington, Seattle, WA (United States); Ezzell, G [Mayo Clinic Arizona, Phoenix, AZ (United States); Miller, B [Henry Ford Health System, Clinton Township, MI (United States); Yorke, E [Memorial Sloan-Kettering Cancer Center, New York, NY (United States)

    2014-06-15

    Clinical radiotherapy data clearly demonstrate the link between the quality and safety of radiation treatments and the outcome for patients. The medical physicist plays an essential role in this process. To ensure the highest quality treatments, the medical physicist must understand and employ modern quality improvement techniques. This extends well beyond the duties traditionally associated with prescriptive QA measures. This session will review the current best practices for improving quality and safety in radiation therapy. General elements of quality management will be reviewed including: what makes a good quality management structure, the use of prospective risk analysis such as FMEA, and the use of incident learning. All of these practices are recommended in society-level documents and are incorporated into the new Practice Accreditation program developed by ASTRO. To be effective, however, these techniques must be practical in a resource-limited environment. This session will therefore focus on practical tools such as the newly-released radiation oncology incident learning system, RO-ILS, supported by AAPM and ASTRO. With these general constructs in mind, a case study will be presented of quality management in an SBRT service. An example FMEA risk assessment will be presented along with incident learning examples including root cause analysis. As the physicist's role as “quality officer” continues to evolve it will be essential to understand and employ the most effective techniques for quality improvement. This session will provide a concrete overview of the fundamentals in quality and safety. Learning Objectives: Recognize the essential elements of a good quality management system in radiotherapy. Understand the value of incident learning and the AAPM/ASTRO ROILS incident learning system. Appreciate failure mode and effects analysis as a risk assessment tool and its use in resource-limited environments. Understand the fundamental principles of good

  3. TH-E-19A-01: Quality and Safety in Radiation Therapy

    International Nuclear Information System (INIS)

    Ford, E; Ezzell, G; Miller, B; Yorke, E

    2014-01-01

    Clinical radiotherapy data clearly demonstrate the link between the quality and safety of radiation treatments and the outcome for patients. The medical physicist plays an essential role in this process. To ensure the highest quality treatments, the medical physicist must understand and employ modern quality improvement techniques. This extends well beyond the duties traditionally associated with prescriptive QA measures. This session will review the current best practices for improving quality and safety in radiation therapy. General elements of quality management will be reviewed including: what makes a good quality management structure, the use of prospective risk analysis such as FMEA, and the use of incident learning. All of these practices are recommended in society-level documents and are incorporated into the new Practice Accreditation program developed by ASTRO. To be effective, however, these techniques must be practical in a resource-limited environment. This session will therefore focus on practical tools such as the newly-released radiation oncology incident learning system, RO-ILS, supported by AAPM and ASTRO. With these general constructs in mind, a case study will be presented of quality management in an SBRT service. An example FMEA risk assessment will be presented along with incident learning examples including root cause analysis. As the physicist's role as “quality officer” continues to evolve it will be essential to understand and employ the most effective techniques for quality improvement. This session will provide a concrete overview of the fundamentals in quality and safety. Learning Objectives: Recognize the essential elements of a good quality management system in radiotherapy. Understand the value of incident learning and the AAPM/ASTRO ROILS incident learning system. Appreciate failure mode and effects analysis as a risk assessment tool and its use in resource-limited environments. Understand the fundamental principles of good

  4. Research priorities for coordinating management of food safety and water quality.

    Science.gov (United States)

    Crohn, David M; Bianchi, Mary L

    2008-01-01

    Efforts to exclude disease organisms from farms growing irrigated lettuce and leafy vegetables on California's central coast are conflicting with traditionally accepted strategies to protect surface water quality. To begin resolving this dilemma, over 100 officials, researchers, and industry representatives gathered in April 2007 to set research priorities that could lead to effective co-management of both food safety and water quality. Following the meeting, research priorities were refined and ordered by way of a Delphi process completed by 35 meeting participants. Although water quality and food safety experts conceptualized the issues differently, there were no deep disagreements with respect to research needs. Top priority was given to investigating the fate of pathogens potentially present on farms. Intermediate priorities included characterizing the influence of specific farm management practices on food safety and improving our understanding of vector processes. A scientific subdiscipline focusing on competing risks is needed to characterize and resolve conflicts between human and environmental health.

  5. Quality and safety of nuclear installations: the role of administration, and, nuclear safety and regulatory procedures

    International Nuclear Information System (INIS)

    Queniart, D.

    1979-12-01

    In the first paper the author defines the concepts of safety and quality and describes the means of intervention by the Public Authorities in safety matters of nuclear installations. These include individual authorisations, definition and application of technical rules and surveillance of installations. In the second paper he defines the distinction between radiation protection and safety and presents the legislative and regulatory plan for nuclear safety in France. A central safety service for nuclear installations was created in March 1973 within the Ministry of Industrial and Scientific Development, where, amongst other tasks, it draws up regulatory procedures and organizes inspections of the installations. The main American regulations for light water reactors are outlined and the French regulatory system for different types of reactors discussed

  6. Principles and Practices for Quality Assurance and Quality Control

    Science.gov (United States)

    Jones, Berwyn E.

    1999-01-01

    Quality assurance and quality control are vital parts of highway runoff water-quality monitoring projects. To be effective, project quality assurance must address all aspects of the project, including project management responsibilities and resources, data quality objectives, sampling and analysis plans, data-collection protocols, data quality-control plans, data-assessment procedures and requirements, and project outputs. Quality control ensures that the data quality objectives are achieved as planned. The historical development and current state of the art of quality assurance and quality control concepts described in this report can be applied to evaluation of data from prior projects.

  7. Safety Evaluation Approach with Security Controls for Safety I and C Systems on Nuclear Power Plants

    International Nuclear Information System (INIS)

    Kim, D. H.; Jeong, S. Y.; Kim, Y. M.; Park, H. S.; Lee, M. S.; Kim, T. H.

    2016-01-01

    This paper addresses concepts of safety and security and relations between them for assessing effects of security features in safety systems. Also, evaluation approach for avoiding confliction with safety requirements and cyber security features which may be adopted in safety-related digital I and C system will be described. In this paper, safety-security life cycle model based confliction avoidance method was proposed to evaluate the effects when the cyber security control features are implemented in the safety I and C system. Also, safety effect evaluation results using the proposed evaluation method were described. In case of technical security controls, many of them are expected to conflict with safety requirements, otherwise operational and managerial controls are not relatively. Safety measures and cyber security measures for nuclear power plants should be implemented not to conflict with one another. Where safety function and security features are both required within the systems, and also where security features are implemented within safety systems, they should be justified

  8. Safety Evaluation Approach with Security Controls for Safety I and C Systems on Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Kim, D. H.; Jeong, S. Y.; Kim, Y. M.; Park, H. S. [KINS, Daejeon (Korea, Republic of); Lee, M. S.; Kim, T. H. [Formal Works Inc., Seoul (Korea, Republic of)

    2016-05-15

    This paper addresses concepts of safety and security and relations between them for assessing effects of security features in safety systems. Also, evaluation approach for avoiding confliction with safety requirements and cyber security features which may be adopted in safety-related digital I and C system will be described. In this paper, safety-security life cycle model based confliction avoidance method was proposed to evaluate the effects when the cyber security control features are implemented in the safety I and C system. Also, safety effect evaluation results using the proposed evaluation method were described. In case of technical security controls, many of them are expected to conflict with safety requirements, otherwise operational and managerial controls are not relatively. Safety measures and cyber security measures for nuclear power plants should be implemented not to conflict with one another. Where safety function and security features are both required within the systems, and also where security features are implemented within safety systems, they should be justified.

  9. Checking quality control?

    DEFF Research Database (Denmark)

    Brodersen, Lars

    2005-01-01

    How is quality control doing within the community of GIS, web-services based on geo-information, GI etc.?......How is quality control doing within the community of GIS, web-services based on geo-information, GI etc.?...

  10. Development of a quality assurance safety assessment database for near surface radioactive waste disposal

    International Nuclear Information System (INIS)

    Park, J. W.; Kim, C. L.; Park, J. B.; Lee, E. Y.; Lee, Y. M.; Kang, C. H.; Zhou, W.; Kozak, M. W.

    2003-01-01

    A quality assurance safety assessment database, called QUARK (QUality Assurance program for Radioactive waste management in Korea), has been developed to manage both analysis information and parameter database for safety assessment of Low- and Intermediate-Level radioactive Waste (LILW) disposal facility in Korea. QUARK is such a tool that serves QA purposes for managing safety assessment information properly and securely. In QUARK, the information is organized and linked to maximize the integrity of information and traceability. QUARK provides guidance to conduct safety assessment analysis, from scenario generation to result analysis, and provides a window to inspect and trace previous safety assessment analysis and parameter values. QUARK also provides default database for safety assessment staff who construct input data files using SAGE(Safety Assessment Groundwater Evaluation), a safety assessment computer code

  11. Management concepts and safety applications for nuclear fuel facilities

    International Nuclear Information System (INIS)

    Eisner, H.; Scotti, R.S.

    1995-05-01

    This report presents an overview of effectiveness of management control of safety. It reviews several modern management control theories as well as the general functions of management and relates them to safety issues at the corporate and at the process safety management (PSM) program level. Following these discussions, structured technique for assessing management of the safety function is suggested. Seven modern management control theories are summarized, including business process reengineering, the learning organization, capability maturity, total quality management, quality assurance and control, reliability centered maintenance, and industrial process safety. Each of these theories is examined for-its principal characteristics and implications for safety management. The five general management functions of planning, organizing, directing, monitoring, and integrating, which together provide control over all company operations, are discussed. Under the broad categories of Safety Culture, Leadership and Commitment, and Operating Excellence, key corporate safety elements and their subelements are examined. The three categories under which PSM program-level safety issues are described are Technology, Personnel, and Facilities

  12. Management concepts and safety applications for nuclear fuel facilities

    Energy Technology Data Exchange (ETDEWEB)

    Eisner, H.; Scotti, R.S. [George Washington Univ., Washington, DC (United States). School of Engineering and Applied Science; Delicate, W.S. [KEVRIC Co., Inc., Silver Spring, MD (United States)

    1995-05-01

    This report presents an overview of effectiveness of management control of safety. It reviews several modern management control theories as well as the general functions of management and relates them to safety issues at the corporate and at the process safety management (PSM) program level. Following these discussions, structured technique for assessing management of the safety function is suggested. Seven modern management control theories are summarized, including business process reengineering, the learning organization, capability maturity, total quality management, quality assurance and control, reliability centered maintenance, and industrial process safety. Each of these theories is examined for-its principal characteristics and implications for safety management. The five general management functions of planning, organizing, directing, monitoring, and integrating, which together provide control over all company operations, are discussed. Under the broad categories of Safety Culture, Leadership and Commitment, and Operating Excellence, key corporate safety elements and their subelements are examined. The three categories under which PSM program-level safety issues are described are Technology, Personnel, and Facilities.

  13. Quality assurance for safety in the radioactive waste management: a quality assurance system in Novi Han radioactive waste repository

    International Nuclear Information System (INIS)

    Petrova, A.; Kolev, I.

    2000-01-01

    Novi Han Radioactive Waste Repository (RWR) is still the only place in Bulgaria for storage of low and intermediate level radioactive waste. It is necessary to establish and maintain a Quality Assurance (QA) system to ensure that the RWR can be operated safely with regard to the health and safety of the general public and site personnel. A QA system has to establish the basic requirements for quality assurance in order to enhance nuclear safety by continuously improving the methods employed to achieve quality. It is envisaged that the QA system for the Novi Han RWR will cover the operation and maintenance of the radioactive waste disposal facilities, the radiation protection and monitoring of the site, as well as the scientific and technology development aspects. The functions of the Novi Han RWR presume the availability of an environmental management system. It is appropriate to establish a QA system based on the requirements of the ISO Standards 9001 and 14000, using the recommendations of the IAEA (Quality assurance for safety in NPPs and other nuclear installations, code and safety guides Q1-Q14). (authors)

  14. Restructuring within an academic health center to support quality and safety: the development of the Center for Quality and Safety at the Massachusetts General Hospital.

    Science.gov (United States)

    Bohmer, Richard M J; Bloom, Jonathan D; Mort, Elizabeth A; Demehin, Akinluwa A; Meyer, Gregg S

    2009-12-01

    Recent focus on the need to improve the quality and safety of health care has created new challenges for academic health centers (AHCs). Whereas previously quality was largely assumed, today it is increasingly quantifiable and requires organized systems for improvement. Traditional structures and cultures within AHCs, although well suited to the tripartite missions of teaching, research, and clinical care, are not easily adaptable to the tasks of measuring, reporting, and improving quality. Here, the authors use a case study of Massachusetts General Hospital's efforts to restructure quality and safety to illustrate the value of beginning with a focus on organizational culture, using a systematic process of engaging clinical leadership, developing an organizational framework dependent on proven business principles, leveraging focus events, and maintaining executive dedication to execution of the initiative. The case provides a generalizable example for AHCs of how applying explicit management design can foster robust organizational change with relatively modest incremental financial resources.

  15. Quality assurance program plan for 324 Building B-Cell safety cleanout project (BCCP)

    International Nuclear Information System (INIS)

    Tanke, J.M.

    1997-01-01

    This Quality Assurance Program Plan (QAPP) provides information on how the Quality Assurance Program is implemented for the 324 Building B-Cell Safety Cleanout Project (BCCP). This QAPP is responsive to the Westinghouse Hanford Company Quality Assurance Program and Implementation Plan, WHC-SP-1131, for 10 CFR 830.120, Nuclear Safety Management, Quality Assurance Requirements; and DOE Order 5700.6C, Quality Assurance. This QAPP supersedes PNNL PNL-MA-70 QAP Quality Assurance Plan No. WTC-050 Rev. 2, issue date May 3, 1996. This QAPP has been developed specifically for the BCCP. It applies to those items and tasks which affect the completion of activities identified in the work breakdown structure of the Project Management Plan (PMP). These activities include all aspects of decontaminating B-Cell and project related operations within the 324 Building as it relates to the specific activities of this project. General facility activities (i.e. 324 Building Operations) are covered in the Building 324 QAPP. In addition, this QAPP supports the related quality assurance activities addressed in CM-2-14, Hazardous Material Packaging and Shipping, and HSRCM-1, Hanford Site Radiological Control Manual, The 324 Building is currently transitioning from being a Pacific Northwest National Laboratory (PNNL) managed facility to a B and W Hanford Company (BWHC) managed facility. During this transition process existing, PNNL procedures and documents will be utilized until replaced by BWHC procedures and documents. These documents conform to the requirements found in PNL-MA-70, Quality Assurance Manual and PNL-MA-8 1, Hazardous Materials Shipping Manual. The Quality Assurance Program Index (QAPI) contained in Table 1 provides a matrix which shows how project activities relate to 10 CFR 83 0.120 and 5700.6C criteria. Quality Assurance program requirements will be addressed separate from the requirements specified in this document. Other Hanford Site organizations/companies may be

  16. Safety and quality management at the high flux reactor Petten

    International Nuclear Information System (INIS)

    Zurita, A.; Ahlf, J.

    1995-01-01

    The High Flux Reactor (HFR) is one high power multi-purpose materials testing research reactor of the tank-in-pool type, cooled and moderated by light-water. It is operated at 45 MW at a prescribed schedule of 11 cycles per year, each comprising 25 operation days and three shut-down days. Since the licence for the operation of HFR was granted in 1962, a total of 14 amendments to the original licence have been made following different modifications in the installations. In the meantime, international nuclear standards were developed, especially in the framework of the NUSS programme of the IAEA, which were adopted by the Dutch Licensing Authorities. In order to implement the new standards, the situation at the HFR was comprehensively reviewed in the course of an audit performed by the Dutch Licensing Authorities in 1988. This also resulted in formulating the task of setting-up an 'HFR - Integral Quality Assurance Handbook' (HFR-IQAD) involving both organizations JRCIAM and ECN, which had the unique framework and basic guideline to assure the safe and efficient operation and exploitation of the HFR and to promote safety and quality in all aspects of HFR related activities. The assurance of safe and efficient operation and exploitation of the HFR is condensed together under the concepts of safety and quality of services and is achieved through the safety and quality management. (orig.)

  17. Development of nuclear power plant online monitoring system using statistical quality control

    International Nuclear Information System (INIS)

    An, Sang Ha

    2006-02-01

    Statistical Quality Control techniques have been applied to many aspects of industrial engineering. An application to nuclear power plant maintenance and control is also presented that can greatly improve plant safety. As a demonstration of such an approach, a specific system is analyzed: the reactor coolant pumps (RCP) and the fouling resistance of heat exchanger. This research uses Shewart X-bar, R charts, Cumulative Sum charts (CUSUM), and Sequential Probability Ratio Test (SPRT) to analyze the process for the state of statistical control. And we made Control Chart Analyzer (CCA) to support these analyses that can make a decision of error in process. The analysis shows that statistical process control methods can be applied as an early warning system capable of identifying significant equipment problems well in advance of traditional control room alarm indicators. Such a system would provide operators with enough time to respond to possible emergency situations and thus improve plant safety and reliability

  18. Environmental radiation control and quality management system in design and operation of sealed radioactive sources

    International Nuclear Information System (INIS)

    Hussein, A.Z.

    2007-01-01

    New environmental regulations and radiation safety standards are being implemented almost daily to ensure radiation safety, in particular for practices causing exposures to undue radiation doses. A particular emphasis of real challenge for organizations and users of radiation sources has to be for proper radiological safety assessment and is becoming cost effectively to be prepared for auditing. Special concern for the environment is of global . nature, and hence environmental auditing has been and will continue to be an essential practice for improving the environment and for meeting the relevant regulations and standards. In general, most facilities that deal with radioactive sources undertake strict safety measures in terms of personnel radiation protection, handling procedures and security. Hence, those measures should comply with the requirements of the environmental protection standards. Accordingly, a successful quality management system must balance realities of organization and personnel in achieving quality objectives. Organizational principles are found in the technical aspects of' quality management, such as, charting, requirements, measurements, procedures, ... , etc. Human principles are found in the communication side of quality management (e.g. meetings, ,decision making, ,teams, ... , etc). The quality management must understand and balance skills needed to blend them together. Large gamma irradiators present a high potential radiation hazard to the surrounding environment, since the amount of radioactivity is of the order of (P Bq) and a very high dose rates are produced during irradiation. Application of environmental radiation control deemed by regulatory authority and a proper quality management system by the utility would serve public health and safety

  19. Technical safety requirements control level verification

    International Nuclear Information System (INIS)

    STEWART, J.L.

    1999-01-01

    A Technical Safety Requirement (TSR) control level verification process was developed for the Tank Waste Remediation System (TWRS) TSRs at the Hanford Site in Richland, WA, at the direction of the US. Department of Energy, Richland Operations Office (RL). The objective of the effort was to develop a process to ensure that the TWRS TSR controls are designated and managed at the appropriate levels as Safety Limits (SLs), Limiting Control Settings (LCSs), Limiting Conditions for Operation (LCOs), Administrative Controls (ACs), or Design Features. The TSR control level verification process was developed and implemented by a team of contractor personnel with the participation of Fluor Daniel Hanford, Inc. (FDH), the Project Hanford Management Contract (PHMC) integrating contractor, and RL representatives. The team was composed of individuals with the following experience base: nuclear safety analysis; licensing; nuclear industry and DOE-complex TSR preparation/review experience; tank farm operations; FDH policy and compliance; and RL-TWRS oversight. Each TSR control level designation was completed utilizing TSR control logic diagrams and TSR criteria checklists based on DOE Orders, Standards, Contractor TSR policy, and other guidance. The control logic diagrams and criteria checklists were reviewed and modified by team members during team meetings. The TSR control level verification process was used to systematically evaluate 12 LCOs, 22 AC programs, and approximately 100 program key elements identified in the TWRS TSR document. The verification of each TSR control required a team consensus. Based on the results of the process, refinements were identified and the TWRS TSRs were modified as appropriate. A final report documenting key assumptions and the control level designation for each TSR control was prepared and is maintained on file for future reference. The results of the process were used as a reference in the RL review of the final TWRS TSRs and control suite. RL

  20. [Colonoscopy quality control as a requirement of colorectal cancer screening].

    Science.gov (United States)

    Quintero, Enrique; Alarcón-Fernández, Onofre; Jover, Rodrigo

    2013-11-01

    The strategies used in population-based colorectal screening strategies culminate in colonoscopy and consequently the success of these programs largely depends on the quality of this diagnostic test. The main factors to consider when evaluating quality are scientific-technical quality, safety, patient satisfaction, and accessibility. Quality indicators allow variability among hospitals, endoscopy units and endoscopists to be determined and can identify those not achieving recommended standards. In Spain, the working group for colonoscopy quality of the Spanish Society of Gastroenterology and the Spanish Society of Gastrointestinal Endoscopy have recently drawn up a Clinical Practice Guideline that contains the available evidence on the quality of screening colonoscopy, as well as the basic requirements that must be met by endoscopy units and endoscopists carrying out this procedure. The implementation of training programs and screening colonoscopy quality controls are strongly recommended to guarantee the success of population-based colorectal cancer screening. Copyright © 2013 Elsevier España, S.L. and AEEH y AEG. All rights reserved.

  1. Safety in Agri-food chains

    NARCIS (Netherlands)

    Luning, P.A.; Vlieghere, de F.; Verhé, R.

    2006-01-01

    Increasing public demand for adequate and safe food supply has led to extensive development in the field of plant-animal production, food processing, quality and safety procedures, food analysis and control and regulations. However, safety of food can only be guaranteed by the integration of control

  2. Modelling the microbial quality and safety of foods

    NARCIS (Netherlands)

    Wijtzes, T.

    1996-01-01

    Quality and safety of foods are often influenced by the presence and growth of microorganisms. Microorganisms in foods can be divided into two groups: pathogenic organisms, causing illness, and microorganisms that are not harmful to health, but that can spoil a product. Presence and growth of

  3. Ferrocyanide Safety Program: Data requirements for the ferrocyanide safety issue developed through the data quality objectives (DQO) process

    International Nuclear Information System (INIS)

    Buck, J.W.; Anderson, C.M.; Pulsipher, B.A.; Toth, J.J.; Turner, P.J.; Cash, R.J.; Dukelow, G.T.; Meacham, J.E.

    1993-12-01

    This document records the data quality objectives (DQO) process applied to the Ferrocyanide Waste Tank Safety Issue at the Hanford Site by the Pacific Northwest Laboratory and Westinghouse Hanford Company. Specifically, the major recommendations and findings from this Ferrocyanide DQO process are presented so that decision makers can determine the type, quantity, and quality of data required for addressing tank safety issues. The decision logic diagrams and error tolerance equations also are provided. Finally, the document includes the DQO sample-size formulas for determining specific tank sampling requirements

  4. Regulatory control of nuclear safety in Finland. Annual report 2008

    International Nuclear Information System (INIS)

    Kainulainen, E.

    2009-06-01

    This report covers the regulatory control of nuclear safety in 2008, including the design, construction and operation of nuclear facilities, as well as nuclear waste management and nuclear materials. The control of nuclear facilities and nuclear waste management, as well as nuclear non-proliferation, concern two STUK departments: Nuclear Reactor Regulation and Nuclear Waste and Material Regulation. It constitutes the report on regulatory control in the field of nuclear energy, which the Radiation and Nuclear Safety Authority (STUK) is required to submit to the Ministry of Employment and the Economy pursuant to section 121 of the Finnish Nuclear Energy Decree. The first parts of the report explain the basics of the nuclear safety regulation included as part of STUK's responsibilities, as well as the objectives of the operations, and briefly introduce the objects of regulation. The chapter concerning the development and implementation of legislation and regulations describes changes in nuclear legislation, as well as the progress of STUK's YVL Guide revision. The chapter also includes a summary of the application of the updated YVL Guides to nuclear facilities. The section concerning the regulation of nuclear facilities contains a complete safety assessment of the nuclear facilities currently in operation or under construction. For the nuclear facilities in operation, the section describes plant operation, events during operation, annual maintenance, development of the plants and their safety, and observations made during monitoring. Data and observations gained during regulatory activities are reviewed with a focus on ensuring the safety functions of nuclear facilities and the integrity of structures and components. The report also includes a description of the oversight of the operations and quality management of organisations, oversight of operational experience feedback activities, and the results of these oversight activities. The radiation safety of nuclear

  5. Quality Control of Concrete Structure For APR1400 Construction

    International Nuclear Information System (INIS)

    Seo, Inseop; Song, Changhak; Kim, Duill

    2012-01-01

    Nuclear structure shall be constructed to protect internal facilities in the normal operation against external accidents such as the radiation shielding, earthquakes and to be leak-proof of radioactive substances to the external environment in case of loss of coolants. containment and auxiliary building of nuclear power plants are built in reinforced concrete structures to maintain these protection functions. Nuclear structures shall be designed to ensure soundness in operation since they are located on the waterfront where is easy do drain the cooling water and so deterioration and damage of concrete structures caused by seawater can occur. Durability is ensured for concrete structures of APR1400, a Korea standard NPP, in compliance with all safety requirements. In particular, owners perform quality control directly on the production and pouring of cast in place concrete for the concrete structure construction to make sure concrete structures established with quality homogeneity and durability. This report is to look into the quality control standard and management status of cast in place concrete for APR1400 construction

  6. Health Information Technology in Healthcare Quality and Patient Safety: Literature Review.

    Science.gov (United States)

    Feldman, Sue S; Buchalter, Scott; Hayes, Leslie W

    2018-06-04

    The area of healthcare quality and patient safety is starting to use health information technology to prevent reportable events, identify them before they become issues, and act on events that are thought to be unavoidable. As healthcare organizations begin to explore the use of health information technology in this realm, it is often unclear where fiscal and human efforts should be focused. The purpose of this study was to provide a foundation for understanding where to focus health information technology fiscal and human resources as well as expectations for the use of health information technology in healthcare quality and patient safety. A literature review was conducted to identify peer-reviewed publications reporting on the actual use of health information technology in healthcare quality and patient safety. Inductive thematic analysis with open coding was used to categorize a total of 41 studies. Three pre-set categories were used: prevention, identification, and action. Three additional categories were formed through coding: challenges, outcomes, and location. This study identifies five main categories across seven study settings. A majority of the studies used health IT for identification and prevention of healthcare quality and patient safety issues. In this realm, alerts, clinical decision support, and customized health IT solutions were most often implemented. Implementation, interface design, and culture were most often noted as challenges. This study provides valuable information as organizations determine where they stand to get the most "bang for their buck" relative to health IT for quality and patient safety. Knowing what implementations are being effectivity used by other organizations helps with fiscal and human resource planning as well as managing expectations relative to cost, scope, and outcomes. The findings from this scan of the literature suggest that having organizational champion leaders that can shepherd implementation, impact culture

  7. Selection of chemical markers for the quality control of medicinal plants of the genus Cecropia.

    Science.gov (United States)

    Rivera-Mondragón, Andrés; Ortíz, Orlando O; Bijttebier, Sebastiaan; Vlietinck, Arnold; Apers, Sandra; Pieters, Luc; Caballero-George, Catherina

    2017-12-01

    Several Cecropia (Cecropiaceae) species are traditionally used in Latin America for the treatment of a variety of diseases including diabetes, arterial hypertension, asthma, bronchitis, anxiety, and inflammation. At present, a number of commercial products based on these plants have been introduced into the market with very little information on methods for guaranteeing their quality and safety. This work proposes potential chemical markers for the quality control of the raw materials of Cecropia obtusifolia Bertol., Cecropia peltata L., Cecropia glaziovii Snethl., Cecropia pachystachya Trécul, and Cecropia hololeuca Miq. The Herbal Chemical Marker Ranking System (Herb MaRS) developed by the National Institute of Complementary Medicine (NICM) at the University of Western Sydney was used for selecting chemical markers for the quality control of selected medicinal species of Cecropia. This review covers the period from 1982 to 2016. Chlorogenic acid, flavonoidal glycosides (orientin, isoorientin, vitexin, isovitexin, and rutin), catechin, epicatechin, procyanidins (B2, B5, and C1), steroids (β-sitosterol), and triterpenoids (α-amyrin, pomolic, tormentic and ursolic acids) were selected as chemical markers for the quality control of the leaves. It is necessary to establish comprehensive standards for guaranteeing quality, safety and efficacy of herbal drugs. The selection of adequate chemical markers for quality control purposes requires a good knowledge about the chemical composition of medicinal plants and their associated biological properties. To the best of our knowledge this review article is the first to address the identification and quantitative determination of the chemical markers for the genus Cecropia.

  8. Segmentation Scheme for Safety Enhancement of Engineered Safety Features Component Control System

    International Nuclear Information System (INIS)

    Lee, Sangseok; Sohn, Kwangyoung; Lee, Junku; Park, Geunok

    2013-01-01

    Common Caused Failure (CCF) or undetectable failure would adversely impact safety functions of ESF-CCS in the existing nuclear power plants. We propose the segmentation scheme to solve these problems. Main function assignment to segments in the proposed segmentation scheme is based on functional dependency and critical function success path by using the dependency depth matrix. The segment has functional independence and physical isolation. The segmentation structure is that prohibit failure propagation to others from undetectable failures. Therefore, the segmentation system structure has robustness to undetectable failures. The segmentation system structure has functional diversity. The specific function in the segment defected by CCF, the specific function could be maintained by diverse control function that assigned to other segments. Device level control signals and system level control signals are separated and also control signal and status signals are separated due to signal transmission paths are allocated independently based on signal type. In this kind of design, single device failure or failures on signal path in the channel couldn't result in the loss of all segmented functions simultaneously. Thus the proposed segmentation function is the design scheme that improves availability of safety functions. In conventional ESF-CCS, the single controller generates the signal to control the multiple safety functions, and the reliability is achieved by multiplication within the channel. This design has a drawback causing the loss of multiple functions due to the CCF (Common Cause Failure) and single failure Heterogeneous controller guarantees the diversity ensuring the execution of safety functions against the CCF and single failure, but requiring a lot of resources like manpower and cost. The segmentation technology based on the compartmentalization and functional diversification decreases the CCF and single failure nonetheless the identical types of controllers

  9. Segmentation Scheme for Safety Enhancement of Engineered Safety Features Component Control System

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sangseok; Sohn, Kwangyoung [Korea Reliability Technology and System, Daejeon (Korea, Republic of); Lee, Junku; Park, Geunok [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-05-15

    Common Caused Failure (CCF) or undetectable failure would adversely impact safety functions of ESF-CCS in the existing nuclear power plants. We propose the segmentation scheme to solve these problems. Main function assignment to segments in the proposed segmentation scheme is based on functional dependency and critical function success path by using the dependency depth matrix. The segment has functional independence and physical isolation. The segmentation structure is that prohibit failure propagation to others from undetectable failures. Therefore, the segmentation system structure has robustness to undetectable failures. The segmentation system structure has functional diversity. The specific function in the segment defected by CCF, the specific function could be maintained by diverse control function that assigned to other segments. Device level control signals and system level control signals are separated and also control signal and status signals are separated due to signal transmission paths are allocated independently based on signal type. In this kind of design, single device failure or failures on signal path in the channel couldn't result in the loss of all segmented functions simultaneously. Thus the proposed segmentation function is the design scheme that improves availability of safety functions. In conventional ESF-CCS, the single controller generates the signal to control the multiple safety functions, and the reliability is achieved by multiplication within the channel. This design has a drawback causing the loss of multiple functions due to the CCF (Common Cause Failure) and single failure Heterogeneous controller guarantees the diversity ensuring the execution of safety functions against the CCF and single failure, but requiring a lot of resources like manpower and cost. The segmentation technology based on the compartmentalization and functional diversification decreases the CCF and single failure nonetheless the identical types of

  10. Safety Management System in Croatia Control Ltd.

    OpenAIRE

    Pavlin, Stanislav; Sorić, Vedran; Bilać, Dragan; Dimnik, Igor; Galić, Daniel

    2009-01-01

    International Civil Aviation Organization and other international aviation organizations regulate the safety in civil aviation. In the recent years the International Civil Aviation Organization has introduced the concept of the safety management system through several documents among which the most important is the 2006 Safety Management Manual. It treats the safety management system in all the segments of civil aviation, from carriers, aerodromes and air traffic control to design, constructi...

  11. Roles of the operator and the safety services in nuclear power plant quality assurance

    International Nuclear Information System (INIS)

    Widmer, M.; Perrot, J.

    1985-01-01

    With regard to the operation of nuclear power plants, Electricite de France formally recognized in 1973 that it was necessary for safety reasons and economically acceptable to adopt organizational principles of quality assurance that would be applicable both to its own activities and to those of its suppliers. Generally speaking, the form and spirit of the quality assurance programme chosen is based largely on the Code of Practice No. 50-C-QA. In particular, the programme focuses on the flexible character of quality assurance requirements and stresses that in the final analysis product quality depends above all on those to whom the project has been assigned, because it is they who are responsible for meeting the quality objectives set. Ten years of experience with the suppliers of Electricite de France has shown that these suppliers, after some initial difficulty, have been able to adapt the application of quality assurance so as to achieve satisfactory quality as regards both safety and availability. In the case of the French standard nuclear power plants, quality assurance is particularly important thanks to the traceability which it affords and to the allowance for corrective measures which it demands. The safety services normally take action related to quality assurance in three ways: through regulation, the analysis of measures to assure plant safety, and plant supervision. As regards regulation, an order has just been published relating to design, construction and operational quality in base-load nuclear power plants. The requirements laid down in this document incorporate the recommendations of the IAEA Code on quality assurance. (author)

  12. Quality control of intelligence research

    International Nuclear Information System (INIS)

    Lu Yan; Xin Pingping; Wu Jian

    2014-01-01

    Quality control of intelligence research is the core issue of intelligence management, is a problem in study of information science This paper focuses on the performance of intelligence to explain the significance of intelligence research quality control. In summing up the results of the study on the basis of the analysis, discusses quality control methods in intelligence research, introduces the experience of foreign intelligence research quality control, proposes some recommendations to improve quality control in intelligence research. (authors)

  13. The quality and safety of nuclear plants: the part played by the administrative authorities

    International Nuclear Information System (INIS)

    Queniart, Daniel

    1976-01-01

    After specifying the notions of 'safety' and 'quality', the terms and conditions governing the intervention of the public authorities in the matter of safety of nuclear plants are described: individual permits, the establishing and application of technical rules of a general character, surveillance of the plants. The criteria and regulations guiding the evaluation of safety and quality and, in conclusion, insisting on the necessity for permanent discussions among the various organizations concerned are presented [fr

  14. Interaction between production control and quality control

    NARCIS (Netherlands)

    Bij, van der J.D.; Ekert, van J.H.W.

    1999-01-01

    Describes a qualitative study on interaction between systems for production control and quality control within industrial organisations. Production control and quality control interact in a sense. Good performance for one aspect often influences or frustrates the performance of the other. As far as

  15. 46 CFR 61.30-20 - Automatic control and safety tests.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Automatic control and safety tests. 61.30-20 Section 61... TESTS AND INSPECTIONS Tests and Inspections of Fired Thermal Fluid Heaters § 61.30-20 Automatic control and safety tests. Operational tests and checks of all safety and limit controls, combustion controls...

  16. Association of adherence to epilepsy quality standards with seizure control.

    Science.gov (United States)

    Moura, Lidia M V R; Mendez, Diego Yacaman; Jesus, Jonathan De; Andrade, Rogger A; Weissman, Joel S; Vickrey, Barbara G; Hoch, Daniel B

    2015-11-01

    We assessed the relationship between adherence to epilepsy quality measures (EQM) and seizure control over 2-3 years in a retrospective cohort study. 6150 patients were identified at two large academic medical centers with a primary or secondary diagnosis of epilepsy, were 18-85 years old and seen in outpatient general neurology or epilepsy units between June 2011 and May 2014. Patients were included if: their initial visit was between June 2011 and June 2012, treatment was with ≥1 anti-seizure drug, there was ≥1 visit per year during the timeframe, and seizure frequency was documented at initial and final visits, yielding 162 patients/1055 visits from which socio-demographic, clinical and care quality data were abstracted. Quality care was assessed as (1) percent adherence to up to 8 eligible EQM, and (2) defect-free care (DFC: adherence to all eligible EQM). Seizure control (SC) was defined as ≥50% reduction in average seizures/month between initial and final visits. Chi-square and t-test compared care quality with seizure control. Logistic regression was used to assess the relationships between SC, quality of care and subspecialist involvement. Care quality, reflected by documentation of seizure frequency, addressing therapeutic interventions, and referral to a comprehensive epilepsy center, all exceeded 80% adherence. Care quality as reflected by documentation of seizure type, etiology or syndrome; assessment of side effects, counseling about epilepsy safety and women's issues, and screening for psychiatric disorders ranged from 40 to 57%. Mean EQM adherence across all applicable measures was associated with greater seizure control (p=0.0098). DFC was low (=8%) and did not covary with seizure control (p=0.55). The SC and non-SC groups only differed on epilepsy etiology (p=0.04). Exploratory analysis showed that mean quality scores are associated with seizure control (OR=4.9 [1.3-18.5], p=0.017) while controlling for the effect of subspecialty involvement

  17. Quality control of 5mg diazepam suppositories manipulated in the city of Campos Goytacazes – RJ

    OpenAIRE

    Renata Aparecida Venturi Canzian; Fernanda Fraga Pessanha; Jean Carlos Brandão Storck

    2012-01-01

    Diazepam suppositories are widely used by children and elderly, and require close attention to quality control because it is a controlled prescription drug. The objective of the study was to analyze diazepam suppositories manipulated in Campos dos Goytacazes, RJ, to verify if they are within the required quality standards, and offer safety and efficiency to patients. We analyzed samples of 5mg diazepam suppositories acquired in five randomly selected pharmacies, identified as Pharmacy A, Phar...

  18. Quality control in radiotherapy

    International Nuclear Information System (INIS)

    Batalla, A.

    2009-01-01

    The authors discuss the modalities and periodicities of internal quality control on radiotherapy installations. They indicate the different concerned systems and the aspects and items to be controlled (patient and personnel security, apparatus mechanical characteristics, beam quality, image quality, isodose and irradiation duration calculation, data transfer). They present the measurement instruments and tools used for the mechanical controls, dose measurement, beam homogeneity and symmetry, anatomic data acquisition systems, and dose distribution and control imagery calculation

  19. Safety precautions in atomic pile control (1962)

    International Nuclear Information System (INIS)

    Furet, J.

    1962-01-01

    We have been led to study the problem of safety in atomic pile control as a result of our participation on the one hand in the planning of C.E.A. atomic piles, and on the other hand in the pile safety sub omission considering atomic pile safety of operational or planned C.E.A. piles. We have thus had to consider the wishes occurring in piles during their operation and also their behaviour in the dynamic state The present work deals mainly with the importance of intrinsic safety devices, with the influence of reactivity variations on the power fluctuations during accidental operation, and with the development of robust and reliable safety appliances. The starting p accident has been especially studied both for low-flux piles where a compromise is necessary between the response time of the safety appliances and the statistical fluctuations and for high lux piles where xenon poisoning has an effect on the lower limit of the velocity of reactivity liberation. The desirability has been stressed of automation as a safety factor in atomic pile control. The details required for an understanding of the diagrams of the apparatus are given. (author) [fr

  20. Manual on quality assurance for computer software related to the safety of nuclear power plants

    International Nuclear Information System (INIS)

    1988-01-01

    The objective of the Manual is to provide guidance in the assurance of quality of specification, design, maintenance and use of computer software related to items and activities important to safety (hereinafter referred to as safety related) in nuclear power plants. This guidance is consistent with, and supplements, the requirements and recommendations of Quality Assurance for Safety in Nuclear Power Plants: A Code of Practice, 50-C-QA, and related Safety Guides on quality assurance for nuclear power plants. Annex A identifies the IAEA documents referenced in the Manual. The Manual is intended to be of use to all those who, in any way, are involved with software for safety related applications for nuclear power plants, including auditors who may be called upon to audit management systems and product software. Figs

  1. High perfomance liquid chromatography fingerprint analysis for quality control of brotowali (Tinospora crispa)

    Science.gov (United States)

    Syarifah, V. B.; Rafi, M.; Wahyuni, W. T.

    2017-05-01

    Brotowali (Tinospora crispa) is widely used in Indonesia as ingredient of herbal medicine formulation. To ensure the quality, safety, and efficacy of herbal medicine products, its chemical constituents should be continuously evaluated. High performance liquid chromatography (HPLC) fingerprint is one of powerful technique for this quality control process. In this study, HPLC fingerprint analysis method was developed for quality control of brotowali. HPLC analysis was performed in C18 column and detection was performed using photodiode array detector. The optimum mobile phase for brotowali fingerprint was acetonitrile (ACN) and 0.1% formic acid in gradient elution mode at a flow rate of 1 mL/min. The number of peaks detected in HPLC fingerprint of brotowali was 32 peaks and 23 peaks for stems and leaves, respectively. Berberine as marker compound was detected at retention time of 20.525 minutes. Evaluation of analytical performance including precision, reproducibility, and stability prove that this HPLC fingerprint analysis was reliable and could be applied for quality control of brotowali.

  2. Applying different quality and safety models in healthcare improvement work: Boundary objects and system thinking

    International Nuclear Information System (INIS)

    Wiig, Siri; Robert, Glenn; Anderson, Janet E.; Pietikainen, Elina; Reiman, Teemu; Macchi, Luigi; Aase, Karina

    2014-01-01

    A number of theoretical models can be applied to help guide quality improvement and patient safety interventions in hospitals. However there are often significant differences between such models and, therefore, their potential contribution when applied in diverse contexts. The aim of this paper is to explore how two such models have been applied by hospitals to improve quality and safety. We describe and compare the models: (1) The Organizing for Quality (OQ) model, and (2) the Design for Integrated Safety Culture (DISC) model. We analyze the theoretical foundations of the models, and show, by using a retrospective comparative case study approach from two European hospitals, how these models have been applied to improve quality and safety. The analysis shows that differences appear in the theoretical foundations, practical approaches and applications of the models. Nevertheless, the case studies indicate that the choice between the OQ and DISC models is of less importance for guiding the practice of quality and safety improvement work, as they are both systemic and share some important characteristics. The main contribution of the models lay in their role as boundary objects directing attention towards organizational and systems thinking, culture, and collaboration

  3. Design and Implementation of the Harvard Fellowship in Patient Safety and Quality.

    Science.gov (United States)

    Gandhi, Tejal K; Abookire, Susan A; Kachalia, Allen; Sands, Kenneth; Mort, Elizabeth; Bommarito, Grace; Gagne, Jane; Sato, Luke; Weingart, Saul N

    2016-01-01

    The Harvard Fellowship in Patient Safety and Quality is a 2-year physician-oriented training program with a strong operational orientation, embedding trainees in the quality departments of participating hospitals. It also integrates didactic and experiential learning and offers the option of obtaining a master's degree in public health. The program focuses on methodologically rigorous improvement and measurement, with an emphasis on the development and implementation of innovative practice. The operational orientation is intended to foster the professional development of future quality and safety leaders. The purpose of this article is to describe the design and development of the fellowship. © The Author(s) 2014.

  4. Construction of Traceability System for Quality Safety of Cereal and Oil Products

    Science.gov (United States)

    Zheng, Huoguo; Liu, Shihong; Meng, Hong; Hu, Haiyan

    After several significant food safety incident, global food industry and governments in many countries are putting increasing emphasis on establishment of food traceability systems. Food traceability has become an effective way in food quality and safety management. The traceability system for quality safety of cereal and oil products was designed and implemented with HACCP and FMECA method, encoding, information processing, and hardware R&D technology etc, according to the whole supply chain of cereal and oil products. Results indicated that the system provide not only the management in origin, processing, circulating and consuming for enterprise, but also tracing service for customers and supervisor by means of telephone, internet, SMS, touch machine and mobile terminal.

  5. MANAGEMENT OF QUALITY AND SAFETY OF FOOD PRODUCTS OF ANIMAL ORIGIN

    Directory of Open Access Journals (Sweden)

    Goryana Yonkova

    2016-12-01

    Full Text Available Bulgaria is famous not only in Europe but throughout the world, except for its rich natural and cultural heritage, but also traditional dairy products (yogurt and cheese - cow, sheep, buffalo and goats; yellow cheese, honey and bee products, rose oil. To be competitive on national and international markets, food production must meet the requirements for quality assurance and food safety. The article presents the key economic indicators and threats related to quality management and safety of food products of animal origin in relation to the conservation of components of the environment and human health.

  6. Quality systems for radiotherapy: Impact by a central authority for improved accuracy, safety and accident prevention

    International Nuclear Information System (INIS)

    Jaervinen, H.; Sipilae, P.; Parkkinen, R.; Kosunen, A.; Jokelainen, I.

    2001-01-01

    High accuracy in radiotherapy is required for the good outcome of the treatments, which in turn implies the need to develop comprehensive Quality Systems for the operation of the clinic. The legal requirements as well as the recommendation by professional societies support this modern approach for improved accuracy, safety and accident prevention. The actions of a national radiation protection authority can play an important role in this development. In this paper, the actions of the authority in Finland (STUK) for the control of the implementation of the new requirements are reviewed. It is concluded that the role of the authorities should not be limited to simple control actions, but comprehensive practical support for the development of the Quality Systems should be provided. (author)

  7. Postharvest quality and safety maintenance of the physical ...

    African Journals Online (AJOL)

    Biodegradable edible coatings from Moringa oil(MO) and Neem oil (NO) was applied to carrot fruits in order to provide environmentally friendly, healthy treatments (with which to better preserve fresh fruit quality) and safety during postharvest storage at ambient temperature of 27± 3oC and relative humidity of 50-60% .

  8. Food Safety: an Integral Part of Food Security

    International Nuclear Information System (INIS)

    Kilian, Lizette

    2012-01-01

    In recent years, many countries have developed integrated and harmonized food safety and quality control guidelines in accordance with national legislation and international standards to protect the health of consumers. But food safety standards alone are not enough. Radiation technology can complement and supplement existing technologies to ensure food security, safety and quality.

  9. Development of Quality Control Method for Glucofarmaka Antidiabetic Jamu by HPLC Fingerprint Analysis

    Directory of Open Access Journals (Sweden)

    Hanifullah Habibie

    2017-04-01

    Full Text Available Herbal medicines become increasingly popular all over the world for preventive and therapeutic purposes. Quality control of herbal medicines is important to make sure their safety and efficacy. Chromatographic fingerprinting has been accepted by the World Health Organization as one reliable strategy for quality control method in herbal medicines. In this study, high-performance liquid chromatography fingerprint analysis was developed as a quality control method for glucofarmaka antidiabetic jamu. The optimum fingerprint chromatogram were obtained using C18 as the stationary phase and linear gradient elution using 10–95% acetonitrile:water as the mobile phase within 60 minutes of elution and detection at 210 nm. About 20 peaks were detected and could be used as fingerprint of glucofarmaka jamu. To evaluate the analytical performance of the method, we determined the precision, reproducibility, and stability. The result of the analytical performance showed reliable results. The proposed method could be used as a quality control method for glucofarmaka antidiabetic jamu and also for its raw materials.

  10. Quality assurance and quality control

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    The practice of nuclear diagnostic imaging requires an appropriate quality assurance program to attain high standards of efficiency and reliability. The International Atomic Energy Agency defines the term quality assurance as ''the closeness with which the outcome of a given procedure approaches some ideal, free from all errors and artifacts.'' The term quality control is used in reference to the specific measures taken to ensure that one particular aspect of the procedure is satisfactory. Therefore, quality assurance is a hospital-wide concept that should involve all aspects of clinical practice. Quality control is concerned with the submission of requests for procedures; the scheduling of patients; the preparation and dispensing of radiopharmaceuticals; the protection of patients, staff, and the general public against radiation hazards and accidents caused by radioactive materials or by faulty equipment; the setting up, use, and maintenance of electronic instruments; the methodology of the actual procedures; the analysis and interpretation of data; the reporting of results; and, finally, the keeping of records. The chapter discusses each of these areas

  11. Quality assurance requirements for the computer software and safety analyses

    International Nuclear Information System (INIS)

    Husarecek, J.

    1992-01-01

    The requirements are given as placed on the development, procurement, maintenance, and application of software for the creation or processing of data during the design, construction, operation, repair, maintenance and safety-related upgrading of nuclear power plants. The verification and validation processes are highlighted, and the requirements put on the software documentation are outlined. The general quality assurance principles applied to safety analyses are characterized. (J.B.). 1 ref

  12. The performance regulatory approach in quality assurance: Its application to safety in nuclear power plants

    International Nuclear Information System (INIS)

    Sajaroff, Pedro M.

    2000-01-01

    In early 1991, the IAEA assembled an Advisory Group on the Comprehensive Revision of the Code and the Safety on Quality Assurance of the NUSS Programme. The Group was made up by specialists from a number of countries and from ISO, FORATOM, the EC and the IAEA itself, and its objective was completed in June 1995. This paper is aimed at describing the conceptual contents of the final draft of the revision 2 of the 50-C-QA Code 'Quality Assurance for Safety in Nuclear Power Plants and other Nuclear Facilities' (hereinafter, the Code) which is essentially based on performance. Although the performance regulatory approach is not new in Argentina and in other countries, what is indeed novel is applying performance based QA. In such a way the Code will contribute to preventing both QA misinterpretations (i.e., a formalistic regulatory requirement) and the execution of non-effective work without attaining the needed quality level (what may be seen as a pathological deviation of QA). The Code contains ten basic requirements to be adopted when QA programmes are established and implemented in nuclear power plants. The goal is improving safety through an improvement in the methods applied for attaining quality. In line with the current developments in quality management techniques, priority is given to effectiveness of the QA programme. All the involved individuals (that is those in the managerial level, those performing the work and those assessing the work performed) must contribute to quality in a co-ordinated manner. The revised Safety Guides are being introduced, standing out those non existing before. Interrelation between quality assurance, safety culture and quality culture is to be noted. Besides QA for safety-related software mentioned as an issue to be considered by the IAEA. (author)

  13. Application of quality assurance program to safety related aging equipment or components

    International Nuclear Information System (INIS)

    Papaiya, N.C.

    1990-01-01

    This paper addresses how quality assurance programs and their criteria are applied to safety related and aging equipment or components used in commercial nuclear plant applications. The QA Programs referred to are 10CFR50 Appendix B and EPRI NP-5652. The QA programs as applicable are applied to equipment/component aging qualification, preventive maintenance, surveillance testing and procurement engineering. The intent of this paper is not the technical issues, methods and research of aging. The paper addresses QA program's application to age-related equipment or components in safety related applications. Quality Assurance Program 10CFR50 Appendix B applies to all safety related aging components or equipment related to the qualification program and associated preventive maintenance and surveillance testing programs. Quality Assurance involvement with procurement engineering for age-related commercial grade items supports EPRI NP-5652 and assures that the dedicated OGI is equal to the item purchased as a basic component to 10CFR50 Appendix B requirements

  14. Safety analysis of control rod drive computers

    International Nuclear Information System (INIS)

    Ehrenberger, W.; Rauch, G.; Schmeil, U.; Maertz, J.; Mainka, E.U.; Nordland, O.; Gloee, G.

    1985-01-01

    The analysis of the most significant user programmes revealed no errors in these programmes. The evaluation of approximately 82 cumulated years of operation demonstrated that the operating system of the control rod positioning processor has a reliability that is sufficiently good for the tasks this computer has to fulfil. Computers can be used for safety relevant tasks. The experience gained with the control rod positioning processor confirms that computers are not less reliable than conventional instrumentation and control system for comparable tasks. The examination and evaluation of computers for safety relevant tasks can be done with programme analysis or statistical evaluation of the operating experience. Programme analysis is recommended for seldom used and well structured programmes. For programmes with a long, cumulated operating time a statistical evaluation is more advisable. The effort for examination and evaluation is not greater than the corresponding effort for conventional instrumentation and control systems. This project has also revealed that, where it is technologically sensible, process controlling computers or microprocessors can be qualified for safety relevant tasks without undue effort. (orig./HP) [de

  15. Quality management and perceptions of teamwork and safety climate in European hospitals

    NARCIS (Netherlands)

    Kristensen, S.; Hammer, A.; Bartels, P.; Sunol, R.; Groene, O.; Thompson, C.A.; Arah, O.A.; Kutaj-Wasikowska, H.; Michel, P.; Wagner, C.

    2015-01-01

    Objective: This study aimed to investigate the associations of quality management systems with teamwork and safety climate, and to describe and compare differences in perceptions of teamwork climate and safety climate among clinical leaders and frontline clinicians. Method: We used a multi-method,

  16. Construction of the All-region Linkage System for Emergency Management of Agricultural Product Quality and Safety in West China

    Institute of Scientific and Technical Information of China (English)

    Hua; YU; Yanbin; QI; Yubao; YAN

    2013-01-01

    Quality and safety of agricultural products are significant for national socioeconomic development,sustainable development,and vital interests of people.To safeguard quality and safety of agricultural products in west China is to safeguard economic safety and ecological safety of the country,public health and social stability,of which an important task is to properly handle emergencies concerning quality and safety of agricultural products.Considering actual conditions of west China,suggestions are given to construct the all-region linkage system for emergency management of agricultural product quality and safety in the local area,enhance the all-region linkage,and improve the linkage efficiency.

  17. Probabilistic safety assessment for instrumentation and control systems in nuclear power plants: an overview

    International Nuclear Information System (INIS)

    Lu, Lixuan; Jiang, Jin

    2004-01-01

    Deregulation in the electricity market has resulted in a number of challenges in the nuclear power industry. Nuclear power plants must find innovative ways to remain competitive by reducing operating costs without jeopardizing safety. Instrumentation and Control (I and C) systems not only play important roles in plant operation, but also in reducing the cost of power generation while maintaining and/or enhancing safety. Therefore, it is extremely important that I and C systems are managed efficiently and economically. With the increasing use of digital technologies, new methods are needed to solve problems associated with various aspects of digital I and C systems. Probabilistic Safety Assessment (PSA) has proved to be an effective method for safety analysis and risk-based decisions, even though challenges are still present. This paper provides an overview of PSA applications in three areas of digital I and C systems in nuclear power plants. These areas are Graded Quality Assurance, Surveillance Testing, and Instrumentation and Control System Design. In addition, PSA application in the regulation of nuclear power plants that adopt digital I and C systems is also investigated. (author)

  18. Implementation Science: New Approaches to Integrating Quality and Safety Education for Nurses Competencies in Nursing Education.

    Science.gov (United States)

    Dolansky, Mary A; Schexnayder, Julie; Patrician, Patricia A; Sales, Anne

    Although quality and safety competencies were developed and disseminated nearly a decade ago by the Quality and Safety Education for Nurses (QSEN) project, the uptake in schools of nursing has been slow. The use of implementation science methods may be useful to accelerate quality and safety competency integration in nursing education. The article includes a definition and description of implementation science methods and practical implementation strategies for nurse educators to consider when integrating the QSEN competencies into nursing curriculum.

  19. Quality management and patient safety: survey results from 102 Hungarian hospitals.

    NARCIS (Netherlands)

    Makai, P.; Klazinga, N.; Wagner, C.; Boncz, I.; Gulácsi, L.

    2009-01-01

    OBJECTIVES: The aim of this study is to describe the development of quality management systems in Hungarian hospitals. It also aims to answer the policy question, whether a separate patient safety policy should be created additional to quality policies, on national as well as hospital level. METHOD:

  20. [On-site quality control of acupuncture randomized controlled trial: design of content and checklist of quality control based on PICOST].

    Science.gov (United States)

    Li, Hong-Jiao; He, Li-Yun; Liu, Zhi-Shun; Sun, Ya-Nan; Yan, Shi-Yan; Liu, Jia; Zhao, Ye; Liu, Bao-Yan

    2014-02-01

    To effectively guarantee quality of randomized controlld trial (RCT) of acupuncture and develop reasonable content and checklist of on-site quality control, influencing factors on quality of acupuncture RCT are analyzed and scientificity of quality control content and feasibility of on-site manipulation are put into overall consideration. Based on content and checklist of on-site quality control in National 11th Five-Year Plan Project Optimization of Comprehensive Treatment Plan for TCM in Prevention and Treatment of Serious Disease and Clinical Assessment on Generic Technology and Quality Control Research, it is proposed that on-site quality control of acupuncture RCT should be conducted with PICOST (patient, intervention, comparison, out come, site and time) as core, especially on quality control of interveners' skills and outcome assessment of blinding, and checklist of on-site quality control is developed to provide references for undertaking groups of the project.

  1. The Health and Safety Executive's regulatory framework for control of nuclear criticality safety

    International Nuclear Information System (INIS)

    Smith, K.; Simister, D.N.

    1991-01-01

    In the United Kingdom the Health and Safety at Work Act, 1974 is the main legal instrument under which risks to people from work activities are controlled. Certain sections of the Nuclear Installations Act, 1965 which deal with the licensing of nuclear sites and the regulatory control of risks arising from them, including the risk from accidental criticality, are relevant statutory provisions of the Health and Safety at Work Act. The responsibility for safety rests with the operator who has to make and implement arrangements to prevent accidental criticality. The adequacy of these arrangements must be demonstrated in a safety case to the regulatory authorities. Operators are encouraged to treat each plant on its own merits and develop the safety case accordingly. The Nuclear Installations Inspectorate (NII), for its part, assesses the adequacy of the operator's safety case against the industry's own standards and criteria, but more particularly against the NII's safety assessment principles and guides, and international standards. Risks should be made as low as reasonably practicable. Generally, the NII seeks improvements in safety using an enforcement policy which operates at a number of levels, ranging from persuasion through discussion to the ultimate deterrent of withdrawal of a site licence. This paper describes the role of the NII, which includes a specialist criticality expertise, within the Health and Safety Executive, in regulating the nuclear sites from the criticality safety viewpoint. (Author)

  2. Integrated Management System Incorporating Quality Management and Management of Environment, Health and Occupational Safety

    International Nuclear Information System (INIS)

    Manchev, B.; Nenkova, B.; Tomov, E.

    2012-01-01

    Risk Engineering Ltd is a Bulgarian private company founded in 1990 to provide engineering and consulting services applicable to each and every field of the energy sector. Since its establishment Risk Engineering Ltd develops, implement and apply a System for quality assurance, certified for the first time by BVQI (now Bureau Veritas Certification) in 1999 for conformity with the standard ISO 9001:1994. Later on, in connection with the revision of the standards of ISO 9000 series and introduction of the standard ISO 9001:2000 a Quality Management System in conformity with the standard ISO 9001:2000 was developed, introduced and certified. At present, Risk Engineering Ltd has got developed, documented, introduced and certified by Lloyd's Register Quality Assurance (LRQA) Quality Management System in compliance with ISO 9001:2008 on the process approach basis. On this basis and including the requirements of the ISO 14001:2004 (regarding the environment) and OHSAS 18001:2007 (regarding the health and occupational safety), Risk Engineering Ltd has developed and introduced Integrated Management System aim at achieving and demonstrating good results regarding protection of the environment, health and occupational safety. The processes under control by the Integrated Management System and applicable at the company are divided in two general types: A) Management processes: Strategic management and Management of the human resources. B) Processes describing the main activities: design/development process; project management; management of industrial projects and technical infrastructure project; construction, installation, repair and operation of power industry facilities; commercial activities and marketing; investigation of energy efficiency of industrial systems and certification of buildings regarding energy efficiency; consulting activity in the field of industry and energy as well as consultant in accordance with the Law of the Spatial Planning; management of the

  3. Safety implications of control systems

    International Nuclear Information System (INIS)

    Smith, O.L.

    1983-01-01

    The Safety Implications of Control Systems Program has three major activities in support of USI-A47. The first task is a failure mode and effects analysis of all plant systems which may potentially induce control system disturbance that have safety implications. This task has made a preliminary study of overfill events and recommended cases for further analysis on the hybrid simulator. Work continues on overcooling and undercooling. A detailed investigation of electric power network is in progress. LERs are providing guidance on important failure modes that will provide initial conditions for further simulator studies. The simulator taks is generating a detailed model of the control system supported by appropriate neutronics, hydraulics, and thermodynamics submodels of all other principal plant components. The simulator is in the last stages of development. Checkout calculations are in progress to establish model stability, robustness, and qualitative credibility. Verification against benchmark codes and plant data will follow

  4. Safety Impacts of the Actuated Signal Control at Urban Intersections

    Directory of Open Access Journals (Sweden)

    Sang Hyuk Lee

    2016-02-01

    Full Text Available To reduce travel time, the actuated signal controls have been implemented at urban intersections. However, the safety impacts of actuated signal controls thus far have rarely been examined. In this assessment of the safety impact of urban intersections with semi-actuated signal controls, the safety performance functions and EB approaches were applied. The semi-actuated signal controls have increased injuries and total crashes in all crash types by around 5.9% and 3.8%, respectively. Regarding the most common crash types, such as angle, sideswipe & rear-end, and head-on crashes, semi-actuated signal controls have been seen to decrease injuries by 7.7%. Total crashes have been reduced by over 9.2% through the use of semi-actuated signal controls. This may be result of optimal signal timings considering traffic conditions during peak time periods. In conclusion, safety impact factors which have been established in this study can be used to improve safety and minimize travel times using semi-actuated signal controls.

  5. Radiation safety and control

    International Nuclear Information System (INIS)

    Kim, Jang Hee; Kim, Gi Sub.

    1996-12-01

    The principal objective of radiological safety control is intended for achievement and maintenance of appropriately safe condition in environmental control for activities involving exposure from the use of radiation. In order to establish these objective, we should be to prevent deterministic effects and to limit the occurrence stochastic effects to level deemed to be acceptable by the application of general principles of radiation protection and systems of dose limitation based on ICRP recommendations. (author). 22 tabs., 13 figs., 11 refs

  6. Radiological safety and control

    International Nuclear Information System (INIS)

    Kim, Jang Hee; Kim, Ki Sub

    1995-01-01

    The practical objective of radiological safety control is intended for achievement and maintenance of appropreately safe condition in environmental control for activities involving exposure from the use of radiation. In order to establish these objectives, we should be to prevent deterministic effects and to limit the occurrence stochastic effects to level deemed to be acceptable by the application of general principles of radiation protection and systems of dose limitation based on ICRP recommendations. 34 tabs., 19 figs., 11 refs. (Author) .new

  7. Optimizing Quality of Care and Patient Safety in Malaysia: The Current Global Initiatives, Gaps and Suggested Solutions.

    Science.gov (United States)

    Jarrar, Mu'taman; Abdul Rahman, Hamzah; Don, Mohammad Sobri

    2015-10-20

    Demand for health care service has significantly increased, while the quality of healthcare and patient safety has become national and international priorities. This paper aims to identify the gaps and the current initiatives for optimizing the quality of care and patient safety in Malaysia. Review of the current literature. Highly cited articles were used as the basis to retrieve and review the current initiatives for optimizing the quality of care and patient safety. The country health plan of Ministry of Health (MOH) Malaysia and the MOH Malaysia Annual Reports were reviewed. The MOH has set four strategies for optimizing quality and sustaining quality of life. The 10th Malaysia Health Plan promotes the theme "1 Care for 1 Malaysia" in order to sustain the quality of care. Despite of these efforts, the total number of complaints received by the medico-legal section of the MOH Malaysia is increasing. The current global initiatives indicted that quality performance generally belong to three main categories: patient; staffing; and working environment related factors. There is no single intervention for optimizing quality of care to maintain patient safety. Multidimensional efforts and interventions are recommended in order to optimize the quality of care and patient safety in Malaysia.

  8. Optimizing Quality of Care and Patient Safety in Malaysia: The Current Global Initiatives, Gaps and Suggested Solutions

    Science.gov (United States)

    Jarrar, Mu’taman; Rahman, Hamzah Abdul; Don, Mohammad Sobri

    2016-01-01

    Background and Objective: Demand for health care service has significantly increased, while the quality of healthcare and patient safety has become national and international priorities. This paper aims to identify the gaps and the current initiatives for optimizing the quality of care and patient safety in Malaysia. Design: Review of the current literature. Highly cited articles were used as the basis to retrieve and review the current initiatives for optimizing the quality of care and patient safety. The country health plan of Ministry of Health (MOH) Malaysia and the MOH Malaysia Annual Reports were reviewed. Results: The MOH has set four strategies for optimizing quality and sustaining quality of life. The 10th Malaysia Health Plan promotes the theme “1 Care for 1 Malaysia” in order to sustain the quality of care. Despite of these efforts, the total number of complaints received by the medico-legal section of the MOH Malaysia is increasing. The current global initiatives indicted that quality performance generally belong to three main categories: patient; staffing; and working environment related factors. Conclusions: There is no single intervention for optimizing quality of care to maintain patient safety. Multidimensional efforts and interventions are recommended in order to optimize the quality of care and patient safety in Malaysia. PMID:26755459

  9. A holistic approach to control process safety risks: Possible ways forward

    International Nuclear Information System (INIS)

    Pasman, H.J.; Knegtering, B.; Rogers, W.J.

    2013-01-01

    Pursuing process safety in a world of continuously increasing requirements is not a simple matter. Keeping balance between producing quality and volume under budget constraints while maintaining an adequate safety level proves time and time again a difficult task given that evidently major accidents cannot be avoided. Lack of resilience from an organizational point of view to absorb unwanted and unforeseen disturbances has in recent years been put forward as a major cause, while organizational erosive drift is shown to be responsible for complacency and degradation of safety attitude. A systems approach to safety provides a new paradigm with the promise of new comprehensive tools. At the same time, one realizes that risk assessment will fall short of identifying and quantifying all possible scenarios. First, human error is in most assessments not included. It is even argued that determining human failure probability by decomposing it to basic elements of error is not possible. Second, the crux of the systemic approach is that safety is an emergent property, which means the same holds for the technological aspect: risk is not fully predictable from failure of components. By surveying and applying recent literature, besides analysing, this paper proposes a way forward by considering resilience of a socio-technical system both from an organizational and a technical side. The latter will for a large part be determined by the plant design. Sufficient redundancy and reserve shall be kept to preserve sufficient resilience, but the question that rises is how. Available methods are risk assessment and process simulation. It is helpful that the relation between risk and resilience analysis has been recently defined. Also, in a preliminary study the elements of resilience of a process have become listed. In the latter, receiving and interpreting weak signals to boost situational awareness plays an important role. To maintain alertness on the functioning of a safety management

  10. Survey of product quality control of radioactive waste

    International Nuclear Information System (INIS)

    Warnecke, E.

    1989-01-01

    The PTB has developed basic procedures with regard to deriving final storage conditions and product quality control. After this, requirements for radioactive waste are derived via safety analysers, in which information about the radioactive waste, the geological overall situation of the site and the layout of the final storage mine, in particular, are included as basic data. The final storage conditions are only determined with the awarding of the planning decision. Compliance with them can be proved by random sample tests on waste containers or via a qualification and inspection of the conditioning process. (DG) [de

  11. Medical Devices; Immunology and Microbiology Devices; Classification of the Assayed Quality Control Material for Clinical Microbiology Assays. Final order.

    Science.gov (United States)

    2017-07-27

    The Food and Drug Administration (FDA, Agency, or we) is classifying the assayed quality control material for clinical microbiology assays into class II (special controls). The special controls that will apply to the device are identified in this order and will be part of the codified language for the assayed quality control material for clinical microbiology assays' classification. The Agency is classifying the device into class II (special controls) to provide a reasonable assurance of safety and effectiveness of the device.

  12. Taking up national safety alerts to improve patient safety in hospitals: The perspective of healthcare quality and risk managers.

    Science.gov (United States)

    Pfeiffer, Yvonne; Schwappach, David

    2016-01-01

    National safety alert systems publish relevant information to improve patient safety in hospitals. However, the information has to be transformed into local action to have an effect on patient safety. We studied three research questions: How do Swiss healthcare quality and risk managers (qm/rm(1)) see their own role in learning from safety alerts issued by the Swiss national voluntary reporting and analysis system? What are their attitudes towards and evaluations of the alerts, and which types of improvement actions were fostered by the safety alerts? A survey was developed and applied to Swiss healthcare risk and quality managers, with a response rate of 39 % (n=116). Descriptive statistics are presented. The qm/rm disseminate and communicate with a broad variety of professional groups about the alerts. While most respondents felt that they should know the alerts and their contents, only a part of them felt responsible for driving organizational change based on the recommendations. However, most respondents used safety alerts to back up their own patient safety goals. The alerts were evaluated positively on various dimensions such as usefulness and were considered as standards of good practice by the majority of the respondents. A range of organizational responses was applied, with disseminating information being the most common. An active role is related to using safety alerts for backing up own patient safety goals. To support an active role of qm/rm in their hospital's learning from safety alerts, appropriate organizational structures should be developed. Furthermore, they could be given special information or training to act as an information hub on the issues discussed in the alerts. Copyright © 2016. Published by Elsevier GmbH.

  13. Competition and safety in the law on technical inspection and control - is it a contradiction?

    International Nuclear Information System (INIS)

    Roth, H.A.

    1987-01-01

    For some time now, objections have been raised against the argument that technical inspection and control should indeed remain a task exlusively for the Technical Control Boards and their offices, organisations and employed inspectors, because competition in this very safety-related sector would not be a positive factor of selection but rather a mechanism reducing the inspection quality, resulting in a hazardous lowering of the safety level. The objections are primarily raised by the free-lance technical experts and their organisations who would like to enlarge their field of activity in this direction. The book at hand discusses the question how much free manoeuvering space there is for the legislative body to deal with such demands and reconcile the interests of safety and competition. The problem is discussed with a view to the Basic Law, which is said to create no legal basis for the demand for more competition in this field. The Basic Law leaves this decision to the discretion of the legislature. (orig./HP) [de

  14. Software product quality control

    CERN Document Server

    Wagner, Stefan

    2013-01-01

    Quality is not a fixed or universal property of software; it depends on the context and goals of its stakeholders. Hence, when you want to develop a high-quality software system, the first step must be a clear and precise specification of quality. Yet even if you get it right and complete, you can be sure that it will become invalid over time. So the only solution is continuous quality control: the steady and explicit evaluation of a product's properties with respect to its updated quality goals.This book guides you in setting up and running continuous quality control in your environment. Star

  15. AEC controlled area safety program

    Energy Technology Data Exchange (ETDEWEB)

    Hendricks, D W [Nevada Operations Office, Atomic Energy Commission, Las Vegas, NV (United States)

    1969-07-01

    The detonation of underground nuclear explosives and the subsequent data recovery efforts require a comprehensive pre- and post-detonation safety program for workers within the controlled area. The general personnel monitoring and environmental surveillance program at the Nevada Test Site are presented. Some of the more unusual health-physics aspects involved in the operation of this program are also discussed. The application of experience gained at the Nevada Test Site is illustrated by description of the on-site operational and safety programs established for Project Gasbuggy. (author)

  16. AEC controlled area safety program

    International Nuclear Information System (INIS)

    Hendricks, D.W.

    1969-01-01

    The detonation of underground nuclear explosives and the subsequent data recovery efforts require a comprehensive pre- and post-detonation safety program for workers within the controlled area. The general personnel monitoring and environmental surveillance program at the Nevada Test Site are presented. Some of the more unusual health-physics aspects involved in the operation of this program are also discussed. The application of experience gained at the Nevada Test Site is illustrated by description of the on-site operational and safety programs established for Project Gasbuggy. (author)

  17. Controlling for quality in the hospital cost function.

    Science.gov (United States)

    Carey, Kathleen; Stefos, Theodore

    2011-06-01

    This paper explores the relationship between the cost and quality of hospital care from the perspective of applied microeconomics. It addresses both theoretical and practical complexities entailed in incorporating hospital quality into the estimation of hospital cost functions. That literature is extended with an empirical analysis that examines the use of 15 Patient Safety Indicators (PSIs) as measures of hospital quality. A total operating cost function is estimated on 2,848 observations from five states drawn from the period 2001 to 2007. In general, findings indicate that the PSIs are successful in capturing variation in hospital cost due to adverse patient safety events. Measures that rely on the aggregate number of adverse events summed over PSIs are found to be superior to risk-adjusted rates for individual PSIs. The marginal cost of an adverse event is estimated to be $22,413. The results contribute to a growing business case for inpatient safety in hospital services.

  18. Quality control and disinfestation of spices for export

    International Nuclear Information System (INIS)

    George, C.K.

    1998-01-01

    India is the largest producer, consumer and exporter of spices in the world. Other than a few, all spices are grown in this country. The production is estimated at 2.6 million tonnes with an export of about 0.22 million tonnes valued around US $ 333 million. India's share in the world trade is over 40 % in quantity and 20 % in value. Many spices produced in India face quality problems as in other countries. For identifying quality produce, grade specifications have been introduced for all the important spices. With the liberalization of government controls, compulsory pre-shipment inspection has been withdrawn unless insisted by the buyer abroad. To meet the sanitary and phytosanitary requirements, the Spices Board has taken up a massive programme for upgradation of quality of Indian spices. Logo mark and Spice House Certificates are awarded to those spice exporting units having necessary infrastructure for assuring quality. By now, 6 units have been accredited to ISO 9000. Though different chemical and non-chemical treatments are available for improving hygienic quality, irradiation appears to be a reliable method. However, its wide application in the spice industry depends upon the conviction of the consumers of its safety. Because of the comprehensive programmes taken up for quality improvement of spices, India is confident of exporting spices meeting quality specifications prescribed by the importing countries. (author)

  19. Quality assurance and quality control

    International Nuclear Information System (INIS)

    Kaden, W.

    1986-01-01

    General preconditions and methods for QA work in the nuclear field are analysed. The application of general QA principles to actual situations is illustrated by examples in the fields of engineering and of the manufacturing of mechanical and electrical components. All QA measures must be fitted to the complexity and relevance of the work steps, which are under consideration. The key to good product quality is the control of working processes. The term 'controlled process' is discussed in detail and examples of feed back systems are given. The main QA measures for the operation of nuclear power plants include the establishment of a Quality Assurance Program, training and qualification of personnel, procurement control, inspection and tests, reviews and audits. These activities are discussed. (orig.)

  20. The impact of safety and quality of health care on Chinese nursing career decision-making.

    Science.gov (United States)

    Zhu, Junhong; Rodgers, Sheila; Melia, Kath M

    2014-05-01

    The aim of the study was to understand why nurses leave nursing practice in China by exploring the process from recruitment to final exit. This report examines the impact of safety and quality of health care on nursing career decision-making from the leavers' perspective. The nursing shortage in China is more serious than in most developed countries, but the loss of nurses through voluntarily leaving nursing practice has not attracted much attention. This qualitative study draws on a grounded theory approach. In-depth interviews with 19 nurses who have left nursing practice and were theoretically sampled from one provincial capital city in Mainland China. 'Loss of confidence in the safety and quality of health care' became one of the main categories from all leavers' accounts of their decision to leave nursing practice. It emerged from three themes 'Perceiving risk in clinical practice', 'Recognising organisational barriers to safety' and 'Failing to meet expectations of patients'. The findings indicate that the essential work value of nursing to the leavers is the safety and quality of care for their patients. When nurses perceived that they could not fulfil this essential work value in their nursing practice, some of them could not accept the compromise to their value of nursing and left voluntarily to get away from the physical and mental stress. However, some nurses had to stay and accept the limitations on the safety and quality of health care. The study suggests that well-qualified nurses voluntarily leaving nursing practice is a danger signal for patients and hospitals, and has caused deterioration in nursing morale for both current and potential nursing workforces. It suggests that safety and quality of health care could be improved when individual nurses are empowered to exercise nursing autonomy with organisational and managerial support. The priority retention strategies need to remove organisational barriers to the safety and quality of health care

  1. Quality control in nuclear medicine

    International Nuclear Information System (INIS)

    Leme, P.R.

    1983-01-01

    The following topics are discussed: objectives of the quality control in nuclear medicine; the necessity of the quality control in nuclear medicine; guidelines and recommendations. An appendix is given concerning the guidelines for the quality control and instrumentation in nuclear medicine. (M.A.) [pt

  2. [JUSTIFICATION OF USING EQUIVALENCE OF THE INDICES OF QUALITY, SAFETY, AND EFFICACY IN DEVELOPING BIOANALOGS].

    Science.gov (United States)

    Niyazov, R R; Goryachev, D V; Gavrishina, E V; Romodanovskii, D P; Dranitsyna, M A

    2015-01-01

    We describe general principles of demonstrating biosimilarity, as well as selecting the biosimilarity margins. Any change in the structure of a biological molecule can modify its functional activity. Therefore, therapeutic equivalence between a biosimilar product and the corresponding reference product cannot be demonstrated using a single criterion. To demonstrate biosimilarity between two medicinal products, their various characteristics have to be evaluated which may, directly or indirectly, justify that clinically significant differences are absent. Insufficient understanding of 6ritical quality attributes brings a risk for the biosimilar product developer. This will either increase the number of non-clinical and clinical tests and trials needed or will result in awareness that the manufacturing process needs to be improved at the late stages of development, after investing significant resources in the development process. At the same time, the specification of the biological medicinal product cannot solely ensure safety and efficacy thereof. Properly characterized and controlled manufacturing process, which ensures consistency in its attributes not adequately controlled in specifications but influencing safety and efficacy profiles and showing their relevance in non-clinical tests and clinical trials, is an additional quality assurance factor. Justification of all development strategy details, including biosimilarity margins, has to be provided each time when the development process is initiated or when proceeding to the next steps. All problems encountered by the developer have to be resolved in close communication with the regulatory authority. In order to increase the quality of investigation and developer's adherence to good practices, clinical trial results should be published in detail.

  3. Risk assessment of safety data link and network communication in digital safety feature control system of nuclear power plant

    International Nuclear Information System (INIS)

    Lee, Sang Hun; Son, Kwang Seop; Jung, Wondea; Kang, Hyun Gook

    2017-01-01

    Highlights: • Safety data communication risk assessment framework and quantitative scheme were proposed. • Fault-tree model of ESFAS unavailability due to safety data communication failure was developed. • Safety data link and network risk were assessed based on various ESF-CCS design specifications. • The effect of fault-tolerant algorithm reliability of safety data network on ESFAS unavailability was assessed. - Abstract: As one of the safety-critical systems in nuclear power plants (NPPs), the Engineered Safety Feature-Component Control System (ESF-CCS) employs safety data link and network communication for the transmission of safety component actuation signals from the group controllers to loop controllers to effectively accommodate various safety-critical field controllers. Since data communication failure risk in the ESF-CCS has yet to be fully quantified, the ESF-CCS employing data communication systems have not been applied in NPPs. This study therefore developed a fault tree model to assess the data link and data network failure-induced unavailability of a system function used to generate an automated control signal for accident mitigation equipment. The current aim is to provide risk information regarding data communication failure in a digital safety feature control system in consideration of interconnection between controllers and the fault-tolerant algorithm implemented in the target system. Based on the developed fault tree model, case studies were performed to quantitatively assess the unavailability of ESF-CCS signal generation due to data link and network failure and its risk effect on safety signal generation failure. This study is expected to provide insight into the risk assessment of safety-critical data communication in a digitalized NPP instrumentation and control system.

  4. 'BeSAFE', effect-evaluation of internet-based, tailored safety information combined with personal counselling on parents' child safety behaviours: study design of a randomized controlled trial

    Directory of Open Access Journals (Sweden)

    van Beeck Eduard F

    2010-08-01

    Full Text Available Abstract Background Injuries in or around the home are the most important cause of death among children aged 0-4 years old. It is also a major source of morbidity and loss of quality of life. In order to reduce the number of injuries, the Consumer Safety Institute introduced the use of Safety Information Leaflets in the Netherlands to provide safety education to parents of children aged 0-4 years. Despite current safety education, necessary safety behaviours are still not taken by a large number of parents, causing unnecessary risk of injury among young children. In an earlier study an E-health module with internet-based, tailored safety information was developed and applied. It concerns an advice for parents on safety behaviours in their homes regarding their child. The aim of this study is to evaluate the effect of this safety information combined with personal counselling on parents' child safety behaviours. Methods/Design Parents who are eligible for the regular well-child visit with their child at child age 5-8 months are invited to participate in this study. Participating parents are randomized into one of two groups: 1 internet-based, tailored safety information combined with personal counselling (intervention group, or 2 personal counselling using the Safety Information Leaflets of the Consumer Safety Institute in the Netherlands for children aged 12 to 24 months (control group. All parents receive safety information on safety topics regarding the prevention of falling, poisoning, drowning and burning. Parents of the intervention group will access the internet-based, tailored safety information module when their child is approximately 10 months old. After completion of the assessment questions, the program compiles a tailored safety advice. The parents are asked to devise and inscribe a personal implementation intention. During the next well-child visit, the Child Health Clinic professional will discuss this tailored safety information

  5. The Effect of Safety Costs on Productivity and Quality: A Case Study of Five Steel Companies in Ahvaz

    Directory of Open Access Journals (Sweden)

    Gholamabbas Shirali

    2016-10-01

    Full Text Available Background The implementation of a safety program is one of the most effective factors in increasing productivity. A look to safety from the perspective of efficiency can indicate necessary investment in safety for all, especially the managers of companies. Objectives The aim of this study was to evaluate the effect of safety costs on some indicators of productivity and quality in industrial companies. Methods This study was a retrospective analysis and was implemented in five steel companies in Ahvaz. The data relating to the safety costs such as staffing costs and total safety costs, and productivity and quality indicators were collected in five years. This information and data were collected according to statistics from documents and archives of safety, accounting, and production sectors of companies. Costs as well as numbers and figures of variables were expressed in the form of per capita and percentage to make the data comparable. Linear and generalized regression models and Wald Chi-Square test were used by the SPSS 22 software to determine the relationships between them. Results Safety costs such as capita labor safety costs and capita total safety costs or percentage safety labor costs to labor costs, showed a significant positive effect on labor productivity, labor competitiveness, total factor productivity, quality index and production rates (in some cases, P = 0.001. Conclusions The total safety cost and safety labor compensation generally, regardless of the nature and quality of the safety management system, can impact productivity, quality and quantity of production in addition to other factors of production. Surely if safety programs are targeted and codified, the effect of the investment will be doubled.

  6. USAEC Controls for Nuclear Criticality Safety

    Energy Technology Data Exchange (ETDEWEB)

    McCluggage, W. C. [Division of Operational Safety, United States Atomic Energy Commission Washington, DC (United States)

    1966-05-15

    This is a paper written to provide a broad general view of the United States Atomic Energy Commission's controls for nuclear criticality safety within its own facilities. Included also is a brief' discussion of the USAEC's methods of obtaining assurance that the controls are being applied. The body of the document contains three sections. The first two describe the functions of the USAEC; the third deals with the contractors. The provisions of the Atomic Energy Act applicable to health and safety are discussed in relation to nuclear criticality safety. The use of United States Atomic Energy Commission manual chapters and Federal regulations is described. The functions of the USAEC Headquarters' offices and the operations offices are briefly outlined. Comments regarding the USAEC's inspection, auditing and appraisal programmes are included. Also briefly mentioned are the basic qualifications which must be met to become a contractor to possess and process or use fissionable materials. On the plant, factory or facility level the duties and responsibilities of industrial management are briefly outlined. The fundamental standards and their origin, together with the principal documents and guides are mentioned. The chief methods of control used by contractors operating large USAEC facilities and plants are described and compared. These include diagrams of how a typical nuclear criticality safety problem is handled from inception, design, construction and finally plant operation. Also included is a brief discussion of the contractors' methods of assuring strict employee compliance with the operating rules and limits. (author)

  7. Technical safety requirements control level verification; TOPICAL

    International Nuclear Information System (INIS)

    STEWART, J.L.

    1999-01-01

    A Technical Safety Requirement (TSR) control level verification process was developed for the Tank Waste Remediation System (TWRS) TSRs at the Hanford Site in Richland, WA, at the direction of the US. Department of Energy, Richland Operations Office (RL). The objective of the effort was to develop a process to ensure that the TWRS TSR controls are designated and managed at the appropriate levels as Safety Limits (SLs), Limiting Control Settings (LCSs), Limiting Conditions for Operation (LCOs), Administrative Controls (ACs), or Design Features. The TSR control level verification process was developed and implemented by a team of contractor personnel with the participation of Fluor Daniel Hanford, Inc. (FDH), the Project Hanford Management Contract (PHMC) integrating contractor, and RL representatives. The team was composed of individuals with the following experience base: nuclear safety analysis; licensing; nuclear industry and DOE-complex TSR preparation/review experience; tank farm operations; FDH policy and compliance; and RL-TWRS oversight. Each TSR control level designation was completed utilizing TSR control logic diagrams and TSR criteria checklists based on DOE Orders, Standards, Contractor TSR policy, and other guidance. The control logic diagrams and criteria checklists were reviewed and modified by team members during team meetings. The TSR control level verification process was used to systematically evaluate 12 LCOs, 22 AC programs, and approximately 100 program key elements identified in the TWRS TSR document. The verification of each TSR control required a team consensus. Based on the results of the process, refinements were identified and the TWRS TSRs were modified as appropriate. A final report documenting key assumptions and the control level designation for each TSR control was prepared and is maintained on file for future reference. The results of the process were used as a reference in the RL review of the final TWRS TSRs and control suite. RL

  8. Quality assurance for safety in nuclear power plants. A code of practice

    International Nuclear Information System (INIS)

    1978-01-01

    The Code of Practice is a part of the International Atomic Energy Agency's programme, referred to as the NUSS programme (Nuclear Safety Standards), for establishing Codes of Practice and Safety Guides relating to land-based stationary thermal neutron power plants. The documents are based on documentation and experience from various national systems and practices. The present document provides the recommended principles and objectives for the establishment and implementation of a quality assurance programme during design, manufacture, construction, commissioning and operation of structures, system and components important to safety. They are applicable by all those responsible for the power plant, by plant designers, suppliers, architect-engineers, plant constructors, plant operators and other organizations participating in activities affecting quality. The Lists of relevant definition and the Provisional List of NUSS Programme Titles are given

  9. Quality and safety evaluation of a Ghanaian polyherbal product EAF ...

    African Journals Online (AJOL)

    McRoy

    means that issues concerning their quality, safety and efficacy need to be answered. In the current study, ... taken by several agencies like the World ..... this class of secondary metabolites detected ... during the manufacturing process as they.

  10. 40 CFR 75.21 - Quality assurance and quality control requirements.

    Science.gov (United States)

    2010-07-01

    ... quality assurance audit or any other audit, the system is out-of-control. The owner or operator shall... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Quality assurance and quality control... assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner or...

  11. Constitution of a centralised data base for the internal quality control in radiotherapy; Constitution d'une base de donnees centralisee pour le controle de qualite interne en radiotherapie

    Energy Technology Data Exchange (ETDEWEB)

    Fau, P.; Rodrigues, C.; Ruchaud, R.; Bravetti, J. [Centre Prive de Radiotherapie de Metz, 57 - Metz (France)

    2009-10-15

    The objective of this project was to implement a centralised data base of internal quality control in radiotherapy according to the criteria of the decree of A.f.s.s.a.p.s. (French agency of sanitary safety of health products on 27 july 2007, about the internal quality control of external radiotherapy facilities. The software on one year meets the objectives: compliance by comparison with A.f.s.s.a.p.s. criteria but particularly optimization of the centralisation and analysis of the internal quality controls. (N.C.)

  12. Quality control of radiopharmaceuticals

    International Nuclear Information System (INIS)

    Kristensen, K.

    1981-01-01

    Quality assurance was introduced in the pharmaceutical field long before it was used in many other areas, and the term quality control has been used in a much broader sense than merely analytical quality control. The term Good Manufacturing Practice (GMP) has been used to describe the system used for producing safe and effective drugs of a uniform quality. GMP has also been used for the industrial production of radiopharmaceuticals. For the preparation and control of radiopharmaceuticals in hospitals a similar system has been named Good Radiopharmacy Practice (GRP). It contains the same elements as GMP but takes into account the special nature of this group of drugs. Data on the assessment of the quality of radiopharmaceuticals in relation to present standards are reviewed. The general conclusion is that the quality of radiopharmaceuticals appears comparable to that of other drugs. It seems possible to establish the production of radiopharmaceuticals, generators and preparation kits in such a way that analytical control of the final product at the hospital may be limited provided the final preparation work is carried out in accordance with GRP principles. The elements of GRP are reviewed. (author)

  13. The quality control and management of the updating of the process measurement and protection system of HFETR

    International Nuclear Information System (INIS)

    Cao Junru; Duan Tianyuan; Zhao Zengqiao; Xing Rujun; Xia Guanghua; Jiang Yiqun

    2001-01-01

    The author emphasizes the presentation of the quality control and management of implement process. Owing to the strict and scientific organizing, the field implement was completed only in 4 months, and comprehensive operation test of reactor was successful at one go. The management target that is safety, high efficiency and high quality, success at one go, was hit

  14. Report on probabilistic safety assessment (PSA) quality assurance in utilization of risk information

    International Nuclear Information System (INIS)

    2006-12-01

    Recently in Japan, introduction of nuclear safety regulations using risk information such as probabilistic safety assessment (PSA) has been considered and utilization of risk information in the rational and practical measures on safety assurance has made a progress to start with the operation or inspection area. The report compiled results of investigation and studies of PSA quality assurance in risk-informed activities in the USA. Relevant regulatory guide and standard review plan as well as issues and recommendations were reviewed for technical adequacy and advancement of probabilistic risk assessment technology in risk-informed decision making. Useful and important information to be referred as issues in PSA quality assurance was identified. (T. Tanaka)

  15. Experience in the implementation of quality assurance program and safety culture assessment of research reactor operation and maintenance

    International Nuclear Information System (INIS)

    Syarip; Suryopratomo, K.

    2001-01-01

    The implementation of quality assurance program and safety culture for research reactor operation are of importance to assure its safety status. It comprises an assessment of the quality of both technical and organizational aspects involved in safety. The method for the assessment is based on judging the quality of fulfillment of a number of essential issues for safety i.e. through audit, interview and/or discussions with personnel and management in plant. However, special consideration should be given to the data processing regarding the fuzzy nature of the data i.e. in answering the questionnaire. To accommodate this situation, the SCAP, a computer program based on fuzzy logic for assessing plant safety status, has been developed. As a case study, the experience in the assessment of Kartini research reactor safety status shows that it is strongly related to the implementation of quality assurance program in reactor operation and awareness of reactor operation staffs to safety culture practice. It is also shown that the application of the fuzzy rule in assessing reactor safety status gives a more realistic result than the traditional approach. (author)

  16. Commercial jet fuel quality control

    Energy Technology Data Exchange (ETDEWEB)

    Strauss, K.H.

    1995-05-01

    The paper discusses the purpose of jet fuel quality control between the refinery and the aircraft. It describes fixed equipment, including various types of filters, and the usefulness and limitations of this equipment. Test equipment is reviewed as are various surveillance procedures. These include the Air Transport Association specification ATA 103, the FAA Advisory Circular 150/5230-4, the International Air Transport Association Guidance Material for Fuel Quality Control and Fuelling Service and the Guidelines for Quality Control at Jointly Operated Fuel Systems. Some past and current quality control problems are briefly mentioned.

  17. SPECT quality control tests

    International Nuclear Information System (INIS)

    Robilotta, C.C.; Rebelo, M.F.S.; Oliveira, M.A.; Abe, R.

    1987-01-01

    Quality control tests of tomographic system composed by a rotatory chamber (CGR Gammatomome T-9000) and a microcomputer are presented. Traditional quality control tests for scintilation chambers and specific tests for tomographic systems are reported. (M.A.C.) [pt

  18. SAFETY: STRICTER CONTROLS IN CONTROLLED AREAS IN THE PS

    CERN Multimedia

    G. Daems

    2001-01-01

    The PS accelerators will soon stop for several months. Work will take place in controlled areas in the PS and will involve many people who are not always aware of the risks associated with the work sites. To guarentee the safety of these workers, the following two measures will be applied: everyone working in a controlled zone - Linacs, PSB, and PS machines tunnels, and transfer lines - must wear, visibly, his CERN access card and his film badge. the CERN access card and the film badge will only be issued after following a basic safety course. Regular checks will be carried out during the shutdown. Anyone without these two items on their person will be obliged to leave the area immediately.

  19. Reliability Analysis on NPP's Safety-Related Control Module with Field Data

    International Nuclear Information System (INIS)

    Lee, Sang Yong; Jung, Jae Hyun; Kim, Seong Hun

    2006-01-01

    The automatic control systems used in nuclear power plant (NPP) consists of numerous control modules that can be considered to be a network of components various complex ways. The control modules require relatively high reliability than industrial electronic products. Reliability prediction provides the rational basis of system designs and also provides the safety significance of system operations. The aim of this paper is to minimize the deficiencies of the traditional reliability prediction method calculation using the available field return data. This way is possible to do more realistic reliability assessment. SAMCHANG Enterprise Company (SEC) has established database containing high quality data at the module and component level from module maintenance in NPP. On the basis of these, this paper compares results that add failure record (field data) to Telcordia-SR-332 reliability prediction model with MIL-HDBK-217F prediction results

  20. Audit Report The Procurement of Safety Class/Safety-Significant Items at the Savannah River Site

    International Nuclear Information System (INIS)

    2009-01-01

    the Savannah River Site. Our review disclosed that the Department had procured and installed safety-class and safety-significant SSCs that did not meet NQA-1 quality standards. Specifically, we identified multiple instances in which critical components did not meet required quality and safety standards. For example: (1) Three structural components were procured and installed by the prime contractor at Savannah River during construction of the MOX Facility that did not meet the technical specifications for items relied on for safety. These substandard items necessitated costly and time consuming remedial action to, among other things, ensure that nonconforming materials and equipment would function within safety margins; (2) In six instances, items used in the construction of TEF failed to satisfy quality standards. In one of these situations, operating procedures had to be modified to ensure that the problem item did not compromise safety; and (3) Finally, at the ISP, one component that did not meet quality standards was procured. The failure of the item could have resulted in a spill of up to 15,000 gallons of high-level radioactive waste. Based on an extensive examination of relevant internal controls and procurement practices, we concluded that these failures were attributable to inadequate attention to quality assurance at Savannah River. Simply put, Departmental controls were not adequate to prevent and/or detect quality assurance problems. For example, Federal and prime contractor officials did not expressly require that subcontractors or lower-tiered vendors comply with quality assurance requirements. Additionally, management did not effectively communicate quality assurance concerns between the several Departmental program elements operating at Savannah River. The procurement and installation of these nonconforming components resulted in cost increases. For example, as of October 2008, the MOX Facility had incurred costs of more than $680,000 due to problems

  1. Educational background of nurses and their perceptions of the quality and safety of patient care.

    Science.gov (United States)

    Swart, Reece P; Pretorius, Ronel; Klopper, Hester

    2015-04-30

    International health systems research confirms the critical role that nurses play in ensuring the delivery of high quality patient care and subsequent patient safety. It is therefore important that the education of nurses should prepare them for the provision of safe care of a high quality. The South African healthcare system is made up of public and private hospitals that employ various categories of nurses. The perceptions of the various categories of nurses with reference to quality of care and patient safety are unknown in South Africa (SA). To determine the relationship between the educational background of nurses and their perceptions of quality of care and patient safety in private surgical units in SA. A descriptive correlational design was used. A questionnaire was used for data collection, after which hierarchical linear modelling was utilised to determine the relationships amongst the variables. Both the registered- and enrolled nurses seemed satisfied with the quality of care and patient safety in the units were they work. Enrolled nurses (ENs) indicated that current efforts to prevent errors are adequate, whilst the registered nurses (RNs) obtained high scores in reporting incidents in surgical wards. From the results it was evident that perceptions of RNs and ENs related to the quality of care and patient safety differed. There seemed to be a statistically-significant difference between RNs and ENs perceptions of the prevention of errors in the unit, losing patient information between shifts and patient incidents related to medication errors, pressure ulcers and falls with injury.

  2. 78 FR 55257 - Patient Safety and Quality Improvement: Civil Money Penalty Inflation Adjustment

    Science.gov (United States)

    2013-09-10

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Patient Safety and Quality Improvement: Civil Money... Civil Rights has determined that an adjustment to the maximum civil money penalty amount for violations... confidentiality and privilege protections of Patient Safety Work Product (PSWP), and procedures for enforcement...

  3. Quality and Safety Assurance of Iron Casts and Manufacturing Processes

    Directory of Open Access Journals (Sweden)

    Kukla S.

    2016-06-01

    Full Text Available The scope of this work focuses on the aspects of quality and safety assurance of the iron cast manufacturing processes. Special attention was given to the processes of quality control and after-machining of iron casts manufactured on automatic foundry lines. Due to low level of automation and huge work intensity at this stage of the process, a model area was established which underwent reorganization in accordance with the assumptions of the World Class Manufacturing (WCM. An analysis of work intensity was carried out and the costs were divided in order to identify operations with no value added, particularly at individual manufacturing departments. Also an analysis of ergonomics at work stations was carried out to eliminate activities that are uncomfortable and dangerous to the workers' health. Several solutions were proposed in terms of rationalization of work organization at iron cast after-machining work stations. The proposed solutions were assessed with the use of multi-criteria assessment tools and then the best variant was selected based on the assumed optimization criteria. The summary of the obtained results reflects benefits from implementation of the proposed solutions.

  4. Quality assurance and quality control of nuclear engineering during construction phase

    International Nuclear Information System (INIS)

    Zhang Zhihua; Deng Yue; Liu Yaoguang; Xu Xianqi; Zhou Shan; Qian Dazhi; Zhang Yang

    2007-01-01

    The quality assurance (QA) and quality control (QC) is a very important work in the nuclear engineering. This paper starts with how to establish quality assurance system of nuclear engineering construction phase, then introduces several experiments and techniques such as the implementation of quality assurance program, the quality assurance and quality control of contractors, the quality surveillance and control of supervisory companies, quality assurance audit and surveillance of builders. (authors)

  5. Quality control of Cordyceps sinensis, a valued traditional Chinese medicine.

    Science.gov (United States)

    Li, S P; Yang, F Q; Tsim, Karl W K

    2006-08-28

    Cordyceps sinensis, a well-known and valued traditional Chinese medicine, is also called DongChongXiaCao (winter worm summer grass) in Chinese. It is commonly used to replenish the kidney and soothe the lung for the treatment of fatigue, night sweating, hyposexualities, hyperglycemia, hyperlipidemia, asthemia after severe illness, respiratory disease, renal dysfunction and renal failure, arrhythmias and other heart disease, and liver disease. As the rarity and upstanding curative effects of natural Cordyceps, several mycelial strains have been isolated from natural Cordyceps and manufactured in large quantities by fermentation technology, and they are commonly sold as health food products in Asia. In addition, some substitutes such as Cordyceps militaris also have been used and adulterants also confused the market. Therefore, quality control of C. sinensis and its products is very important to ensure their safety and efficacy. Herein, markers and analytical methods for quality control of Cordyceps were reviewed and discussed.

  6. Operation safety of control systems. Principles and methods

    International Nuclear Information System (INIS)

    Aubry, J.F.; Chatelet, E.

    2008-01-01

    This article presents the main operation safety methods that can be implemented to design safe control systems taking into account the behaviour of the different components with each other (binary 'operation/failure' behaviours, non-consistent behaviours and 'hidden' failures, dynamical behaviours and temporal aspects etc). To take into account these different behaviours, advanced qualitative and quantitative methods have to be used which are described in this article: 1 - qualitative methods of analysis: functional analysis, preliminary risk analysis, failure mode and failure effects analyses; 2 - quantitative study of systems operation safety: binary representation models, state space-based methods, event space-based methods; 3 - application to the design of control systems: safe specifications of a control system, qualitative analysis of operation safety, quantitative analysis, example of application; 4 - conclusion. (J.S.)

  7. Verbal Communication Quality Analysis of Human Operators in Main Control Room

    International Nuclear Information System (INIS)

    Kim, Seung Hwan; Park, Jin kyun

    2012-01-01

    Verbal communication problems have been one of the major human factors causing serious problems in many industries. The results of existing researches have revealed that keeping good communication quality is essential to ensure the safety of a large-sized and highly advanced industrial process system. Communication Quality is ensured only when both parties involved in a communication process understand and comprehend each other correctly, and it can be decided based on the correctness of the messages communicated between them. In this paper, we suggested a method to measure the quality of communication during off-normal situation in main control room of nuclear power plants. It evaluates the cosine similarity that is a measure of sentence similarity between two operators by finding the cosine of the angle between them

  8. Quality and safety aspects of reusable plastic food packaging materials : influence of reuse on intrinsic properties

    NARCIS (Netherlands)

    Jetten, J.; Kruijf, N. de

    2002-01-01

    The aim of the project was to develop a comprehensive package of quality assurance criteria for use by the industry and by regulatory authorities to ensure the quality and safety-in-use (sensory, microbiological and chemical safety) of reused plastics for food packaging. The paper describes the

  9. Nuclear power plants - Instrumentation and control systems important for safety - Classification (International Electrotechnical Commission Standard Publication 1226:1993)

    International Nuclear Information System (INIS)

    Stefanik, J.

    1996-01-01

    This international standard established a method of classification of the information and command functions for nuclear power plants, and the I and C and equipment that provide those functions, into categories that designate the importance for safety of the functions, and the associated systems and equipment. The resulting classification then determines relevant design criteria. The design criteria are the measures of quality by which the adequacy of each functions, and the associated systems and equipment in relation to its importance to plant safety is ensured. In this standard, the criteria are those of functionality, reliability, performance, environmental durability and quality assurance. This standard is applicable to all the information and command functions, and the instrumentation and control systems and equipment that provide those functions. The functions, systems and equipment under consideration provide automated protection, closed or open loop control, and information to the operating staff. They keep the NPP conditions inside the safe operating envelope and provide automatic actions, or enable manual actions, that mitigate accidents or prevent or minimize radioactive releases to the site or wider environment. The functions, and the associated systems and equipment that fulfill these roles safeguard the health and safety of the NPP operators and the public. This standard complements, and does not replace or supersede, the Safety Guides and Codes of Practice published by the International Atomic Energy Agency

  10. Beyond metrics? Utilizing 'soft intelligence' for healthcare quality and safety.

    Science.gov (United States)

    Martin, Graham P; McKee, Lorna; Dixon-Woods, Mary

    2015-10-01

    Formal metrics for monitoring the quality and safety of healthcare have a valuable role, but may not, by themselves, yield full insight into the range of fallibilities in organizations. 'Soft intelligence' is usefully understood as the processes and behaviours associated with seeking and interpreting soft data-of the kind that evade easy capture, straightforward classification and simple quantification-to produce forms of knowledge that can provide the basis for intervention. With the aim of examining current and potential practice in relation to soft intelligence, we conducted and analysed 107 in-depth qualitative interviews with senior leaders, including managers and clinicians, involved in healthcare quality and safety in the English National Health Service. We found that participants were in little doubt about the value of softer forms of data, especially for their role in revealing troubling issues that might be obscured by conventional metrics. Their struggles lay in how to access softer data and turn them into a useful form of knowing. Some of the dominant approaches they used risked replicating the limitations of hard, quantitative data. They relied on processes of aggregation and triangulation that prioritised reliability, or on instrumental use of soft data to animate the metrics. The unpredictable, untameable, spontaneous quality of soft data could be lost in efforts to systematize their collection and interpretation to render them more tractable. A more challenging but potentially rewarding approach involved processes and behaviours aimed at disrupting taken-for-granted assumptions about quality, safety, and organizational performance. This approach, which explicitly values the seeking out and the hearing of multiple voices, is consistent with conceptual frameworks of organizational sensemaking and dialogical understandings of knowledge. Using soft intelligence this way can be challenging and discomfiting, but may offer a critical defence against the

  11. Canadian Association of Gastroenterology consensus guidelines on safety and quality indicators in endoscopy.

    Science.gov (United States)

    Armstrong, David; Barkun, Alan; Bridges, Ron; Carter, Rose; de Gara, Chris; Dube, Catherine; Enns, Robert; Hollingworth, Roger; Macintosh, Donald; Borgaonkar, Mark; Forget, Sylviane; Leontiadis, Grigorios; Meddings, Jonathan; Cotton, Peter; Kuipers, Ernst J

    2012-01-01

    Increasing use of gastrointestinal endoscopy, particularly for colorectal cancer screening, and increasing emphasis on health care quality, highlight the need for clearly defined, evidence-based processes to support quality improvement in endoscopy. To identify processes and indicators of quality and safety relevant to high-quality endoscopy service delivery. A multidisciplinary group of 35 voting participants developed recommendation statements and performance indicators. Systematic literature searches generated 50 initial statements that were revised iteratively following a modified Delphi approach using a web-based evaluation and voting tool. Statement development and evidence evaluation followed the AGREE (Appraisal of Guidelines, REsearch and Evaluation) and GRADE (Grading of Recommendations, Assessment, Development and Evaluation) guidelines. At the consensus conference, participants voted anonymously on all statements using a 6-point scale. Subsequent web-based voting evaluated recommendations for specific, individual quality indicators, safety indicators and mandatory endoscopy reporting fields. Consensus was defined a priori as agreement by 80% of participants. Consensus was reached on 23 recommendation statements addressing the following: ethics (statement 1: agreement 100%), facility standards and policies (statements 2 to 9: 90% to 100%), quality assurance (statements 10 to 13: 94% to 100%), training, education, competency and privileges (statements 14 to 19: 97% to 100%), endoscopy reporting standards (statements 20 and 21: 97% to 100%) and patient perceptions (statements 22 and 23: 100%). Additionally, 18 quality indicators (agreement 83% to 100%), 20 safety indicators (agreement 77% to 100%) and 23 recommended endoscopy-reporting elements (agreement 91% to 100%) were identified. The consensus process identified a clear need for high-quality clinical and outcomes research to support quality improvement in the delivery of endoscopy services. The

  12. 76 FR 35130 - Pipeline Safety: Control Room Management/Human Factors

    Science.gov (United States)

    2011-06-16

    ...: Control Room Management/Human Factors AGENCY: Pipeline and Hazardous Materials Safety Administration... the Control Room Management/Human Factors regulations in order to realize the safety benefits sooner... FR 5536). By this amendment to the Control Room Management/Human Factors (CRM) rule, an operator must...

  13. [Endorsement of risk management and patient safety by certification of conformity in health care quality assessment].

    Science.gov (United States)

    Waßmuth, Ralf

    2015-01-01

    Certification of conformity in health care should provide assurance of compliance with quality standards. This also includes risk management and patient safety. Based on a comprehensive definition of quality, beneficial effects on the management of risks and the enhancement of patient safety can be expected from certification of conformity. While these effects have strong face validity, they are currently not sufficiently supported by evidence from health care research. Whether this relates to a lack of evidence or a lack of investigation remains open. Advancing safety culture and "climate", as well as learning from adverse events rely in part on quality management and are at least in part reflected in the certification of healthcare quality. However, again, evidence of the effectiveness of such measures is limited. Moreover, additional factors related to personality, attitude and proactive action of healthcare professionals are crucial factors in advancing risk management and patient safety which are currently not adequately reflected in certification of conformity programs.

  14. The Impact of eHealth on the Quality and Safety of Healthcare

    Science.gov (United States)

    Majeed, Azeem; Black, Ashly; Car, Josip; Anandan, Chantelle; Cresswell, Kathrin; McKinstry, Brian; Pagliari, Claudia; Procter, Rob; Sheikh, Aziz

    There is considerable interest in using information technology (IT) to enhance the quality and safety of healthcare. We undertook a systematic literature review to assess the impact of eHealth applications on the quality and safety of healthcare. We retrieved 46,349 potentially relevant publications, from which we selected 67 relevant systematic reviews for inclusion. The literature was found to be poorly collated and of variable quality in its methodology, reporting and utility. We categorised eHealth applications into three main areas: i). storing, managing and transmission of data; ii). supporting clinical decision-making; and iii). facilitating care from a distance. We found that relative to the potential benefits noted within the literature, little empirical evidence exists in support of these applications. Of the few studies revealing the clearest evidence of benefits, many are from academic clinical centres where developers of new applications have also been directly associated with their evaluation. It is therefore unclear how effective these applications would be if deployed outside the environment in which they were developed. Our review of the impact of eHealth applications on quality and safety of healthcare demonstrated a vast gap between the postulated and empirically demonstrated benefits. In addition, there is a lack of robust research on risks and costs. Consequently, the cost-effectiveness of these interventions has yet to be demonstrated.

  15. Trichinella diagnostics and control: Mandatory and best practices for ensuring food safety

    DEFF Research Database (Denmark)

    Gajadhar, A. A.; Pozio, E.; Gamble, H. R.

    2009-01-01

    Because of its role in human disease, there are increasing global requirements for reliable diagnostic and control methods for Trichinella in food animals to ensure meat safety and to facilitate trade. Consequently, there is a need for standardization of methods, programs, and best practices used...... in various porcine and equine pre- and post-slaughter programs, including farm or herd certification programs is also discussed. A brief review of the effectiveness of meat processing methods, such as freezing, cooking and preserving is provided. The importance of proper quality assurance and its application...

  16. Cooperation and competence in global food chains : perspectives on food quality and safety

    NARCIS (Netherlands)

    Vellema, S.; Boselie, D.M.

    2003-01-01

    Supermarket chains, retailers and wholesalers have made food safety and food quality an integral element of their business strategies. What does this mean for producers in the South, who have to comply with international standards for good agricultural practices as well as with strict food safety

  17. Gust Wind Effects on Stability and Ride Quality of Actively Controlled Maglev Guideway Systems

    Directory of Open Access Journals (Sweden)

    Dong-Ju Min

    2017-01-01

    Full Text Available The purpose of this paper is to present a framework to analyze the interaction between an actively controlled magnetic levitation vehicle and a guideway structure under gusty wind. The equation of motion is presented for a 30-dof maglev vehicle model consisting of one cabin and four bogies. In addition, a lateral electromagnetic suspension (EMS system is introduced to improve the running safety and ride quality of the maglev vehicle subjected to turbulent crosswind. By using the developed simulation tools, the effects of various parameters on the dynamic response of the vehicle and guideway are investigated in the case of the UTM maglev vehicle running on a simply supported guideway and cable-stayed guideway. The simulation results show that the independent lateral EMS and associated control scheme are definitely helpful in improving the running safety and ride quality of the vehicle under gusty wind. In the case of the cable-stayed guideway, at low wind speed, vehicle speed is the dominant factor influencing the dynamic responses of the maglev vehicle and the guideway, but at wind speed over 10 m/s, wind becomes the dominant factor. For the ride quality of the maglev vehicle, wind is also the most influential factor.

  18. EFFECTS OF FIRE FUMES ON ALMOND SAFETY AND QUALITY

    Directory of Open Access Journals (Sweden)

    Amanda Ramírez-Gandolfo

    2011-08-01

    Full Text Available A fire originated and burnt two cold chambers; the present study focused on almonds stored in adjacent chambers (4, 5, 6 and 13 and evaluated both their food safety and quality. Testing for polycyclic aromatic hydrocarbons, polychlorinated dibenzo-p-dioxins and dibenzofurans was carried out in affected facilities, packaging and almonds. Experimental results proved that fire fumes did not reach chambers 4-6, but traces were found in bin packaging of chamber 13; thus, packaging from this chamber were changed. Concentrations of benzo(apyrene were low enough to prove that fire fumes did not get in contact with the stored almonds. Later, only volatile compounds typical of nuts were identified in both raw and toasted almonds. Finally, a trained panel concluded that no sensory signal of fumes reaching almonds was found. This manuscript could be taken as a model protocol to establish whether fire fumes have reached and affected the safety and/or quality of foods. This information will be especially useful for insurance companies.

  19. Improving Quality and Occupational Safety on Automated Casting Lines

    Directory of Open Access Journals (Sweden)

    Kukla S.

    2017-09-01

    Full Text Available The paper presents a practical example of improving quality and occupational safety on automated casting lines. Working conditions on the line of box moulding with horizontal mould split were analysed due to low degree of automation at the stage of cores or filters installation as well as spheroidizing mortar dosing. A simulation analysis was carried out, which was related to the grounds of introducing an automatic mortar dispenser to the mould. To carry out the research, a simulation model of a line in universal Arena software for modelling and simulation of manufacturing systems by Rockwell Software Inc. was created. A simulation experiment was carried out on a model in order to determine basic parameters of the working system. Organization and working conditions in other sections of the line were also analysed, paying particular attention to quality, ergonomics and occupational safety. Ergonomics analysis was carried out on manual cores installation workplace and filters installation workplace, and changes to these workplaces were suggested in order to eliminate actions being unnecessary and onerous for employees.

  20. Safety evaluation for instrumentation and control system upgrading project of Malaysian TRIGA MARK II PUSPATI Research reactor

    International Nuclear Information System (INIS)

    Ridha Roslan; Nik Mohd Faiz Khairuddin

    2013-01-01

    Full-text: Malaysian TRIGA MARK II research reactor has been in safe operation since its first criticality in 1982. The reactor is licensed to be operated by Malaysian Nuclear Agency to perform training and research development related activities. Due to its extensive operation since last three decades, the option of modifications for safety and safety-related item and component become a necessary to replace the outdated equipment to a stat-of-art, reliable technologies. This paper will present the current regulatory activities performed by Atomic Energy Licensing Board (AELB) to ensure the upgrading of analogue to digital instrumentation and control system is implemented in safe manner. The review activity includes documentation review, manufacturer quality audit and on-site inspection for commissioning. The review performed by AELB is based on The International Atomic Energy Agency (IAEA) Safety Requirements NS-R-4, entitled Safety of Research Reactors. During this endeavour, AELB seeks technical cooperation from Korea Institute of Nuclear Safety (KINS), the nuclear experts organization of the country of origin of the instrumentation and control technology. The regulatory activity is still on-going and is expected to be completed by issuance of Authorization for Restart on December 2013. (author)

  1. Active and intelligent packaging: The indication of quality and safety.

    Science.gov (United States)

    Janjarasskul, Theeranun; Suppakul, Panuwat

    2018-03-24

    The food industry has been under growing pressure to feed an exponentially increasing world population and challenged to meet rigorous food safety law and regulation. The plethora of media consumption has provoked consumer demand for safe, sustainable, organic, and wholesome products with "clean" labels. The application of active and intelligent packaging has been commercially adopted by food and pharmaceutical industries as a solution for the future for extending shelf life and simplifying production processes; facilitating complex distribution logistics; reducing, if not eliminating the need for preservatives in food formulations; enabling restricted food packaging applications; providing convenience, improving quality, variety and marketing features; as well as providing essential information to ensure consumer safety. This chapter reviews innovations of active and intelligent packaging which advance packaging technology through both scavenging and releasing systems for shelf life extension, and through diagnostic and identification systems for communicating quality, tracking and brand protection.

  2. Radiological protection and quality control for diagnostic radiology in China

    International Nuclear Information System (INIS)

    Baorong, Yue

    2008-01-01

    Full text: There are 43,000 diagnostic departments, nearly 70,000 X-ray diagnostic facilities, 7,000 CT, 250 million for the annual total numbers of X-ray examinations, 120,000 occupationally exposed workers in diagnostic radiology. 'Basic standards for protection against ionizing radiation and for the safety of radiation sources' is promulgated on October, 2002. This basic standard follows the BSS. 'Rule on the administration of radio-diagnosis and radiotherapy', as a order of the Ministry of Health No. 46, is promulgated by Minister of Health on January 24, 2006. It includes general provisions, requirements and practice, establishment and approval of radio-diagnosis and radiotherapy services, safeguards and quality assurance, and so on. There are a series of radiological protection standards and quality control standards in diagnostic radiology, including 'radiological protection standard for the examination in X-ray diagnosis', 'radiological health protection standards for X-ray examination of child-bearing age women and pregnant women', 'radiological protection standards for the children in X-ray diagnosis', 'standards for radiological protection in medical X-ray diagnosis', 'specification for radiological protection monitoring in medical X-ray diagnosis', 'guide for reasonable application of medical X-ray diagnosis', 'general aspects for quality assurance in medical X-ray image of diagnosis', 'specification of image quality control test for the medical X-ray diagnostic equipment', 'specification of image quality assurance test for X-ray equipment for computed tomography', 'specification for testing of quality control in computed radiography (CR)' and 'specification for testing of quality control in X-ray mammography'. With the X-ray diagnostic equipment, there are acceptant tests, status tests and routing tests in large hospitals. It is poor for routing test in middle and smaller hospitals. CT is used widely in diagnostic radiology, however most workers in CT

  3. 40 CFR 51.359 - Quality control.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 2 2010-07-01 2010-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts are...

  4. What is the value and impact of quality and safety teams? A scoping review

    Directory of Open Access Journals (Sweden)

    Norris Jill M

    2011-08-01

    Full Text Available Abstract Background The purpose of this study was to conduct a scoping review of the literature about the establishment and impact of quality and safety team initiatives in acute care. Methods Studies were identified through electronic searches of Medline, Embase, CINAHL, PsycINFO, ABI Inform, Cochrane databases. Grey literature and bibliographies were also searched. Qualitative or quantitative studies that occurred in acute care, describing how quality and safety teams were established or implemented, the impact of teams, or the barriers and/or facilitators of teams were included. Two reviewers independently extracted data on study design, sample, interventions, and outcomes. Quality assessment of full text articles was done independently by two reviewers. Studies were categorized according to dimensions of quality. Results Of 6,674 articles identified, 99 were included in the study. The heterogeneity of studies and results reported precluded quantitative data analyses. Findings revealed limited information about attributes of successful and unsuccessful team initiatives, barriers and facilitators to team initiatives, unique or combined contribution of selected interventions, or how to effectively establish these teams. Conclusions Not unlike systematic reviews of quality improvement collaboratives, this broad review revealed that while teams reported a number of positive results, there are many methodological issues. This study is unique in utilizing traditional quality assessment and more novel methods of quality assessment and reporting of results (SQUIRE to appraise studies. Rigorous design, evaluation, and reporting of quality and safety team initiatives are required.

  5. Quality control of image-intensifier television chains in Finland

    International Nuclear Information System (INIS)

    Pirinen, M.

    1989-01-01

    There are some 500 image-intensifier television (TV) chains connected to fluoroscopic units in Finland, most installed in the 1970s, although the oldest still in use date back to the late 1960s. To establish performance levels of the chains, 300 of them were assessed in 1982 by the Finnish Centre for Radiation and Nuclear Safety (STUK). Results showed great diversity in the condition of the chains. The main reason was lack of periodical quality assurance of the chains. Recommendations for limits were established from results of assessing three parameters describing the condition of the chains: spatial resolution, automatically controlled dose-rate and contrast sensitivity. Recommendations also advise hospitals on how to arrange alternative quality assurance measurements and observations, either by hospital's maintenance staff, the manufacturer, or the supervising authority (STUK). Results following adoption of the recommendations by hospitals are presented. (author)

  6. The state of quality improvement and patient safety teaching in health professional education in New Zealand.

    Science.gov (United States)

    Robb, Gillian; Stolarek, Iwona; Wells, Susan; Bohm, Gillian

    2017-10-27

    To investigate how quality and patient safety domains are being taught in the pre-registration curricula of health profession education programmes in New Zealand. All tertiary institutions providing training for medicine, nursing, midwifery, dentistry, pharmacy, physiotherapy, dietetics and 11 other allied health professions in New Zealand were contacted and a person with relevant curriculum knowledge was invited to participate. Interviews were conducted using a semi-structured interview guide to explore nine quality and safety domains; improvement science, patient safety, quality and safety culture, evidence-based practice, patient-centred care, teamwork and communication, leadership for change, systems thinking and use of information technology (IT). Transcribed data were extracted and categorised by discipline and domain. Two researchers independently identified and categorised themes within each domain, using a general inductive approach. Forty-nine institutions were contacted and 43 (88%) people were interviewed. The inclusion and extent of quality and safety teaching was variable. Evidence-based practice, patient-centred care and teamwork and communication were the strongest domains and well embedded in programmes, while leadership, systems thinking and the role of IT were less explicitly included. Except for two institutions, improvement science was absent from pre-registration curricula. Patient safety teaching was focused mainly around incident reporting, and to a lesser extent learning from adverse events. Although a 'no blame' culture was articulated as important, the theme of individual accountability was still apparent. While participants agreed that all domains were important, the main barriers to incorporating improvement science and patient safety concepts into existing programmes included an 'already stretched curriculum' and having faculty with limited expertise in these areas. Although the building blocks for improving the quality and safety of

  7. Safety assessment for the above ground storage of Cadmium Safety and Control Rods at the Solid Waste Management Facility

    International Nuclear Information System (INIS)

    Shaw, K.W.

    1993-11-01

    The mission of the Savannah River Site is changing from radioisotope production to waste management and environmental restoration. As such, Reactor Engineering has recently developed a plan to transfer the safety and control rods from the C, K, L, and P reactor disassembly basin areas to the Transuranic (TRU) Waste Storage Pads for long-term, retrievable storage. The TRU pads are located within the Solid Waste Management Facilities at the Savannah River Site. An Unreviewed Safety Question (USQ) Safety Evaluation has been performed for the proposed disassembly basin operations phase of the Cadmium Safety and Control Rod Project. The USQ screening identified a required change to the authorization basis; however, the Proposed Activity does not involve a positive USQ Safety Evaluation. A Hazard Assessment for the Cadmium Safety and Control Rod Project determined that the above-ground storage of the cadmium rods results in no change in hazard level at the TRU pads. A Safety Assessment that specifically addresses the storage (at the TRU pads) phase of the Cadmium Safety and Control Rod Project has been performed. Results of the Safety Assessment support the conclusion that a positive USQ is not involved as a result of the Proposed Activity

  8. Development of embedded Control System for Control and Safety Rod Drive Mechanisms (CSRDMs) of PFBR

    International Nuclear Information System (INIS)

    Kameswari, K.; Palanisami, K.; Thirugnana Murthy, D.; Murali, N.; Satyamurty, S.A.V.

    2013-01-01

    Prototype Fast Breeder Reactor (PFBR), a 500 MWe, Sodium cooled, fast breeder reactor is nearing completion at Kalpakkam, Tamil Nadu. PFBR has two independent, fast acting and diverse shutdown systems, one with nine Control and Safety Rods (CSRs) and another with three Diverse Safety Rods (DSRs), with independent driving mechanisms called CSRDMs and DSRDMs respectively. This paper deals with the development of Real Time Computer based Control system for controlling nine CSRDMs with model based software development environment - SCADE (Safety Critical Application Development Environment). (author)

  9. A strategic approach to quality improvement and patient safety education and resident integration in a general surgery residency.

    Science.gov (United States)

    O'Heron, Colette T; Jarman, Benjamin T

    2014-01-01

    To outline a structured approach for general surgery resident integration into institutional quality improvement and patient safety education and development. A strategic plan to address Accreditation Council for Graduate Medical Education (ACGME) Clinical Learning Environment Review assessments for resident integration into Quality Improvement and Patient Safety initiatives is described. Gundersen Lutheran Medical Foundation is an independent academic medical center graduating three categorical residents per year within an integrated multi-specialty health system serving 19 counties over 3 states. The quality improvement and patient safety education program includes a formal lecture series, online didactic sessions, mandatory quality improvement or patient safety projects, institutional committee membership, an opportunity to serve as a designated American College of Surgeons National Surgical Quality Improvement Project and Quality in Training representative, mandatory morbidity and mortality conference attendance and clinical electives in rural surgery and international settings. Structured education regarding and participation in quality improvement and patient safety programs are able to be accomplished during general surgery residency. The long-term outcomes and benefits of these strategies are unknown at this time and will be difficult to measure with objective data. © 2013 Published by Association of Program Directors in Surgery on behalf of Association of Program Directors in Surgery.

  10. Radiological safety and control

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Sea Young; Yoo, Y S; Lee, J C; Lee, T Y; Lee, J L; Kim, B W; Lee, B J; Chung, K K; Chung, R I; Kim, J S; Lee, H S; Han, Y D; Lee, J I; Lee, K C; Yoon, J H; Sul, C W; Kim, C K; Yoon, K S; Seo, K W; Yoon, Y C [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1996-01-01

    This report describes the annual results of radiological safety and control program of 1995. This program consists of working area monitoring including HANARO, personnel radiation monitoring, education for radiation protection. As a result, the objectives of radiation protection have been achieved satisfactorily through the activities mentioned above. Also, the calibration services were provided to insure accurate radiation measurement in the radiation working places. 21 figs., 39 tabs., 5 refs. (Author) .new.

  11. Selecting Optimal Control Portfolios to Improve Army Aviation Safety

    National Research Council Canada - National Science Library

    Shelton, Sarah

    2001-01-01

    .... The Safety Center chartered the Aviation Safety Investment Strategy Team to evaluate accidents to determine their hazards, or contributing conditions, and their controls, or reduction measures...

  12. Information about the control of nuclear safety in France

    International Nuclear Information System (INIS)

    Gerster, D.

    1994-01-01

    The permanent objective of the French Nuclear Safety Authority is the public information about technical controls performed in French nuclear installations. Three publications from the DSIN (Direction of Nuclear Installations Safety) are devoted to this effort: the MAGNUC Minitel magazine, the annual activity report and the CONTROLE magazine. Details about the content of these publications are given. A large part of the information about control of nuclear safety concerns the incidents and accidents and their importance level. A seriousness scale was created in France at the beginning of 1988 and replaced in April 1994 by the very similar International Nuclear Event Scale (INES). Explanation of this scale is given and illustrated with examples of real events and accidents. However, international comparison between incidents and accidents remains delicate because the detailed content of safety reports can change significantly from one country to another. (J.S.). 1 fig

  13. Network-based production quality control

    Science.gov (United States)

    Kwon, Yongjin; Tseng, Bill; Chiou, Richard

    2007-09-01

    This study investigates the feasibility of remote quality control using a host of advanced automation equipment with Internet accessibility. Recent emphasis on product quality and reduction of waste stems from the dynamic, globalized and customer-driven market, which brings opportunities and threats to companies, depending on the response speed and production strategies. The current trends in industry also include a wide spread of distributed manufacturing systems, where design, production, and management facilities are geographically dispersed. This situation mandates not only the accessibility to remotely located production equipment for monitoring and control, but efficient means of responding to changing environment to counter process variations and diverse customer demands. To compete under such an environment, companies are striving to achieve 100%, sensor-based, automated inspection for zero-defect manufacturing. In this study, the Internet-based quality control scheme is referred to as "E-Quality for Manufacturing" or "EQM" for short. By its definition, EQM refers to a holistic approach to design and to embed efficient quality control functions in the context of network integrated manufacturing systems. Such system let designers located far away from the production facility to monitor, control and adjust the quality inspection processes as production design evolves.

  14. Can traceability improve consumers' confidence in food quality and safety?

    NARCIS (Netherlands)

    Rijswijk, van W.; Cornelisse-Vermaat, J.R.; Frewer, L.J.

    2006-01-01

    Abstract This paper investigates whether the implementation of traceability systems in line with the European General Food Law as well as food labelling laws related to allergens can impact on consumer confidence in food quality and safety. It aims to give insight into consumer demands regarding

  15. Low-Cost Quality Control and Nondestructive Evaluation Technologies for General Aviation Structures

    Science.gov (United States)

    Cramer, K. Elliott; Gavinsky, Bob; Semanskee, Grant

    1998-01-01

    NASA's Advanced General Aviation Transport Experiments (AGATE) Program has as a goal to reduce the overall cost of producing private aviation aircraft while maintaining the safety of these aircraft. In order to successfully meet this goal, it is necessary to develop nondestructive inspection techniques which will facilitate the production of the materials used in these aircraft and assure the quality necessary to maintain airworthiness. This paper will discuss a particular class of general aviation materials and several nondestructive inspection techniques that have proven effective for making these inspections. Additionally, this paper will discuss the investigation and application of other commercially available quality control techniques applicable to these structures.

  16. Administrative controls and quality assurance for the operational phase of nuclear power plants

    International Nuclear Information System (INIS)

    Anon.

    1983-01-01

    This standard provides requirements and recommendations for an adminstrative controls and quality assurance program to help ensure that activities associated with nuclear power plant operation are carried out without undue risk to the health and safety of the public. This standard applies to all activities affecting those functions important to the safety of nuclear power plant structures, systems, and components. Activities included are: design changes, purchasing, fabricating, handling, shipping, storing, cleaning and decontaminating, erecting, installing, inspecting, testing, operating, maintaining, repairing, refueling, modifying and decomissioning. This standard is not specifically intended for application to test, mobile or experimental reactors, nor reactors not subject to U.S. Nuclear Regulatory Commission licensing

  17. The roles of government in improving health care quality and safety.

    Science.gov (United States)

    Tang, Ning; Eisenberg, John M; Meyer, Gregg S

    2004-01-01

    Discussions surrounding the role of government have been and continue to be a favorite American pastime. A framework is provided for understanding the 10 roles that government plays in improving health care quality and safety in the United States. Examples of proposed federal actions to reduce medical errors and enhance patient safety are provided to illustrate the 10 roles: (1) purchase health care, (2) provide health care, (3) ensure access to quality care for vulnerable populations, (4) regulate health care markets, (5) support acquisition of new knowledge, (6) develop and evaluate health technologies and practices, (7) monitor health care quality, (8) inform health care decision makers, (9) develop the health care workforce, and (10) convene stakeholders from across the health care system. Government's responsibility to protect and advance the interests of society includes the delivery of high-quality health care. Because the market alone cannot ensure all Americans access to quality health care, the government must preserve the interests of its citizens by supplementing the market where there are gaps and regulating the market where there is inefficiency or unfairness. The ultimate goal of achieving high quality of care will require strong partnerships among federal, state, and local governments and the private sector. Translating general principles regarding the appropriate role of government into specific actions within a rapidly changing, decentralized delivery system will require the combined efforts of the public and private sectors.

  18. [Quality assurance in food production in Europe according to ISO 90000 and HACCP (Hazard Analysis and Critical Control Points)].

    Science.gov (United States)

    Jouve, J L

    1996-12-01

    HACCP is intended to make food protection programs evolve from a mainly retrospective quality control toward a preventative quality assurance approach and to provide an increased confidence in food safety. In parallel, the continuous evolution of quality concepts in the food industry resulted in the development of quality systems and quality assurance techniques with regard to the EN 29,000 (ISO 9000) series of standards. Specific to the food industry, HACCP can be seen as a very effective method to prepare specific Safety Assurance Plans (cf. the quality assurance plan concept) within a quality systems approach (Jouve, 1993). By reference to ISO 8402, a Quality Assurance Plan (QAP) basically sets out "the specific quality practices, resources and sequence of activities relevant to a particular product, service, contract or project". Quality assurance plans are more particularly useful for projects relating to new products or processes and/or comprising inter-related tasks whose interaction may be complex. In addition, in contractual or regulatory situations, such plans can be used to demonstrate the supplier's capability to meet identified objectives, specification or standards. In the food industry, the management of safety is a critical and complex issue which fits very well in the scope of application of a specific QAP; it is also where the use of HACCP is otherwise recommended by priority.

  19. Code on the safety of nuclear power plants: Quality assurance

    International Nuclear Information System (INIS)

    1988-01-01

    This revised Code provides the principles and objectives for the establishment and implementation of quality assurance programmes applied to both the overall and each of the constituent activities associated with a nuclear power plant project. The quality assurance principles enumerated in the present Code can be usefully applied to nuclear facilities other than nuclear power plants. The quality assurance programme encompasses: (1) the activities that are necessary to achieve the appropriate quality of the respective item or service; and (2) the activities that are necessary for verifying that the required quality is achieved and that objective evidence is produced to that effect. Quality assurance is an essential aspect of good management and the quality assurance programme is the main management tool for a disciplined approach to all activities affecting quality, including, where appropriate, verification that each task has been satisfactorily performed and that necessary corrective actions have been implemented. The principles and objectives provided by the Code are applicable by all those responsible for the nuclear power plant, by plant designers, suppliers, architect-engineers, plant constructors, plant operators and other organizations participating in activities affecting quality. The Code is a revision of the previous Code of Practice (1978) on the same subject of interest to regulatory bodies and experts in quality assurance for design, siting and operation of nuclear power plants. Contents: Definitions; 1. Introduction; 2. Quality assurance programmes; 3. Organization; 4. Document control; 5. Design control; 6. Procurement control; 7. Control of items; 8. Process control; 9. Inspection and test control; 10. Non-conformance control; 11. Corrective actions; 12, Records; 13. Audits

  20. Defining quality metrics and improving safety and outcome in allergy care.

    Science.gov (United States)

    Lee, Stella; Stachler, Robert J; Ferguson, Berrylin J

    2014-04-01

    The delivery of allergy immunotherapy in the otolaryngology office is variable and lacks standardization. Quality metrics encompasses the measurement of factors associated with good patient-centered care. These factors have yet to be defined in the delivery of allergy immunotherapy. We developed and applied quality metrics to 6 allergy practices affiliated with an academic otolaryngic allergy center. This work was conducted at a tertiary academic center providing care to over 1500 patients. We evaluated methods and variability between 6 sites. Tracking of errors and anaphylaxis was initiated across all sites. A nationwide survey of academic and private allergists was used to collect data on current practice and use of quality metrics. The most common types of errors recorded were patient identification errors (n = 4), followed by vial mixing errors (n = 3), and dosing errors (n = 2). There were 7 episodes of anaphylaxis of which 2 were secondary to dosing errors for a rate of 0.01% or 1 in every 10,000 injection visits/year. Site visits showed that 86% of key safety measures were followed. Analysis of nationwide survey responses revealed that quality metrics are still not well defined by either medical or otolaryngic allergy practices. Academic practices were statistically more likely to use quality metrics (p = 0.021) and perform systems reviews and audits in comparison to private practices (p = 0.005). Quality metrics in allergy delivery can help improve safety and quality care. These metrics need to be further defined by otolaryngic allergists in the changing health care environment. © 2014 ARS-AAOA, LLC.

  1. Quality control in dental diagnostic radiology : anomalous in the use of radiological equipment

    International Nuclear Information System (INIS)

    Alcaraz, M.; Martinez-Beneyto, Y.; Jodar, S.; Velasco, E.; Garcia-Vera, M. C.

    2004-01-01

    7,176 official quality control reports on dental diagnostic radiology were studied, relating to dental clinics located in 37 Spanish provinces covering 16 different autonomous Regions. The reports were issued as a result of the entry into force of Royal Decree 2071/1995 on quality control in General Diagnostic Radiology facilities, this Royal Decree was replaced by R. D. 1976/1999. The reports were writen by the UTPR (Technical Unit of Radiological Protection) Agsigma S. A. L., a company approved by the Nuclear Safety Council, and they correspond with the official reports issued during 1996-2001. This meants that a 5-year period has been monitored in order to observe the impacts of the establlishment of this legislation on quality control in intraoral dental diagnostic radiology facilities. The results show that 72.79% of the reports checked in 2001 would comply with the European Union's official recommendation (70 kVp, 8 mA> 1.5 mm of Al and 20 cm collimator length). Significant alterations have detected in a third (30.59%) of the radiological equipment. (Author) 36 refs

  2. Responsibility for quality improvement and patient safety: hospital board and medical staff leadership challenges.

    Science.gov (United States)

    Goeschel, Christine A; Wachter, Robert M; Pronovost, Peter J

    2010-07-01

    Concern about the quality and safety of health care persists, 10 years after the 1999 Institute of Medicine report To Err is Human. Despite growing awareness of quality and safety risks, and significant efforts to improve, progress is difficult to measure. Hospital leaders, including boards and medical staffs, are accountable to improve care, yet they often address this duty independently. Shared responsibility for quality and patient safety improvement presents unique challenges and unprecedented opportunities for boards and medical staffs. To capitalize on the pressure to improve, both groups may benefit from a better understanding of their synergistic potential. Boards should be educated about the quality of care provided in their institutions and about the challenges of valid measurement and accurate reporting. Boards strengthen their quality oversight capacity by recruiting physicians for vacant board seats. Medical staff members strengthen their role as hospital leaders when they understand the unique duties of the governing board. A quality improvement strategy rooted in synergistic efforts by the board and the medical staff may offer the greatest potential for safer care. Such a mutually advantageous approach requires a clear appreciation of roles and responsibilities and respect for differences. In this article, we review these responsibilities, describe opportunities for boards and medical staffs to collaborate as leaders, and offer recommendations for how boards and medical staff members can address the challenges of shared responsibility for quality of care.

  3. Setting quality and safety priorities in a target-rich environment: an academic medical center's challenge.

    Science.gov (United States)

    Mort, Elizabeth A; Demehin, Akinluwa A; Marple, Keith B; McCullough, Kathryn Y; Meyer, Gregg S

    2013-08-01

    Hospitals are continually challenged to provide safer and higher-quality patient care despite resource constraints. With an ever-increasing range of quality and safety targets at the national, state, and local levels, prioritization is crucial in effective institutional quality goal setting and resource allocation.Organizational goal-setting theory is a performance improvement methodology with strong results across many industries. The authors describe a structured goal-setting process they have established at Massachusetts General Hospital for setting annual institutional quality and safety goals. Begun in 2008, this process has been conducted on an annual basis. Quality and safety data are gathered from many sources, both internal and external to the hospital. These data are collated and classified, and multiple approaches are used to identify the most pressing quality issues facing the institution. The conclusions are subject to stringent internal review, and then the top quality goals of the institution are chosen. Specific tactical initiatives and executive owners are assigned to each goal, and metrics are selected to track performance. A reporting tool based on these tactics and metrics is used to deliver progress updates to senior hospital leadership.The hospital has experienced excellent results and strong organizational buy-in using this effective, low-cost, and replicable goal-setting process. It has led to improvements in structural, process, and outcomes aspects of quality.

  4. Patient safety, quality of care, and knowledge translation in the intensive care unit.

    Science.gov (United States)

    Needham, Dale M

    2010-07-01

    A large gap exists between the completion of clinical research demonstrating the benefit of new treatment interventions and improved patient outcomes resulting from implementation of these interventions as part of routine clinical practice. This gap clearly affects patient safety and quality of care. Knowledge translation is important for addressing this gap, but evaluation of the most appropriate and effective knowledge translation methods is still ongoing. Through describing one model for knowledge translation and an example of its implementation, insights can be gained into systematic methods for advancing the implementation of evidence-based interventions to improve safety, quality, and patient outcomes.

  5. Guide for reviewing safety analysis reports for packaging: Review of quality assurance requirements

    International Nuclear Information System (INIS)

    Moon, D.W.

    1988-10-01

    This review section describes quality assurance requirements applying to design, purchase, fabrication, handling, shipping, storing, cleaning, assembly, inspection, testing, operation, maintenance, repair, and modification of components of packaging which are important to safety. The design effort, operation's plans, and quality assurance requirements should be integrated to achieve a system in which the independent QA program is not overly stringent and the application of QA requirements is commensurate with safety significance. The reviewer must verify that the applicant's QA section in the SARP contains package-specific QA information required by DOE Orders and federal regulations that demonstrate compliance. 8 refs

  6. Integrating Quality and Safety Competencies to Improve Outcomes: Application in Infusion Therapy Practice.

    Science.gov (United States)

    Sherwood, Gwen; Nickel, Barbara

    Despite intense scrutiny and process improvement initiatives, patient harm continues to occur in health care with alarming frequency. The Quality and Safety Education for Nursing (QSEN) project provides a roadmap to transform nursing by integrating 6 competencies: patient-centered care, teamwork and collaboration, evidence-based practice, quality improvement, safety, and informatics. As front-line caregivers, nurses encounter inherent risks in their daily work. Infusion therapy is high risk with multiple potential risks for patient harm. This study examines individual and system application of the QSEN competencies and the Infusion Nurses Society's 2016 Infusion Therapy Standards of Practice in the improvement of patient outcomes.

  7. A task force model for statewide change in nursing education: building quality and safety.

    Science.gov (United States)

    Mundt, Mary H; Clark, Margherita Procaccini; Klemczak, Jeanette Wrona

    2013-01-01

    The purpose of this article was to describe a statewide planning process to transform nursing education in Michigan to improve quality and safety of patient care. A task force model was used to engage diverse partners in issue identification, consensus building, and recommendations. An example of a statewide intervention in nursing education and practice that was executed was the Michigan Quality and Safety in Nursing Education Institute, which was held using an integrated approach to academic-practice partners from all state regions. This paper describes the unique advantage of leadership by the Michigan Chief Nurse Executive, the existence of a nursing strategic plan, and a funding model. An overview of the Task Force on Nursing Education is presented with a focus on the model's 10 process steps and resulting seven recommendations. The Michigan Nurse Education Council was established to implement the recommendations that included quality and safety. Copyright © 2013 Elsevier Inc. All rights reserved.

  8. Improving Safety, Quality and Efficiency through the Management of Emerging Processes: The TenarisDalmine Experience

    Science.gov (United States)

    Bonometti, Patrizia

    2012-01-01

    Purpose: The aim of this contribution is to describe a new complexity-science-based approach for improving safety, quality and efficiency and the way it was implemented by TenarisDalmine. Design/methodology/approach: This methodology is called "a safety-building community". It consists of a safety-behaviour social self-construction…

  9. Quantification of microbial quality and safety in minimally processed foods

    NARCIS (Netherlands)

    Zwietering, M.H.

    2002-01-01

    To find a good equilibrium between quality and margin of safety of minimally processed foods, often various hurdles are used. Quantification of the kinetics should be used to approach an optimum processing and to select the main aspects. Due to many factors of which the exact quantitative effect is

  10. Quality and safety evaluation of a Ghanaian polyherbal product EAF ...

    African Journals Online (AJOL)

    Background: The widespread use of herbal medicines in recent years means that issues concerning their quality, safety and efficacy need to be answered. In the current study, the polyherbal formulation EAF-2011 used in the Centre for Scientific Research into Plant Medicine, Mampong- Akwapemfor the management of ...

  11. Evidence-Based Quality Improvement: A recipe for improving medication safety and handover of care

    NARCIS (Netherlands)

    Smeulers, M.

    2016-01-01

    In healthcare we strive to provide the highest possible quality of care. Even though healthcare professionals work together with the intention to provide safe care, medical errors still threaten patient safety. Patient safety has received considerable attention since the beginning of this century,

  12. PATIENT SAFETY IN SURGERY: THE QUALITY OF IMPLEMENTATION OF PATIENT SAFETY CHECKLISTS IN A REGIONAL HOSPITAL

    Directory of Open Access Journals (Sweden)

    V. Karyadinata

    2012-09-01

    Full Text Available Introduction. Patient safety and the avoidance of inhospital adverse events is a key focus of clinical practice and medical audit. A large of proportion of medical errors affect surgical patients in the peri-operative setting. Safety checklists have been adopted by the medical profession from the aviation industry as a cheap and reliable method of avoiding errors which arise from complex or stressful situations. Current evidence suggests that the use of periooperative checklists has led to a decrease in surgical morbidity and hospital costs. Aim. To assess the quality of implementation of a modified patient safety checklist in a UK district general hospital. Methods. An observational tool was designed to assess in real time the peri-operative performance of the surgical safety checklist in patients undergoing general surgical, urological or orthopaedic procedures. Initiation of the checklist, duration of performance and staff participation were audited in real time. Results. 338 cases were monitored. Nurses were most active in initiating the safety checklist. The checklist was performed successfully in less than a minute in most cases. 11-24% of staff (according to professional group present in the operating room did not participate in the checklist. Critical safety checks (patient identity and procedure name were performed in all cases across all specialties. Variations were noted in checking other categories, such as deep vein thrombosis (DVT prophylaxis or patient warming. Conclusions. There is still a potential for improving the practice and culture of surgical patient safety activities. Staff training and designation of patient safety leadership roles is needed in increasing compliance and implementation of patient safety mechanism, such as peri-operative checklists. There is significant data to advocate the need to implement patient safety surgical checklists internationally

  13. Radiopharmaceutical quality control-Pragmatic approach

    International Nuclear Information System (INIS)

    Barbier, Y.

    1994-01-01

    The quality control must be considered in a practical manner. The radiopharmaceuticals are drugs. They must satisfy the quality assurance control. These products are then conform to Pharmacopeia. But sometimes the user must control some data especially radiochemical purity and pH value. On all the administered solutions four controls are compulsory: radionuclide identity, administered radioactivity, organoleptic character and pH

  14. 7 CFR 981.42 - Quality control.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

  15. Quality Attribute Techniques Framework

    Science.gov (United States)

    Chiam, Yin Kia; Zhu, Liming; Staples, Mark

    The quality of software is achieved during its development. Development teams use various techniques to investigate, evaluate and control potential quality problems in their systems. These “Quality Attribute Techniques” target specific product qualities such as safety or security. This paper proposes a framework to capture important characteristics of these techniques. The framework is intended to support process tailoring, by facilitating the selection of techniques for inclusion into process models that target specific product qualities. We use risk management as a theory to accommodate techniques for many product qualities and lifecycle phases. Safety techniques have motivated the framework, and safety and performance techniques have been used to evaluate the framework. The evaluation demonstrates the ability of quality risk management to cover the development lifecycle and to accommodate two different product qualities. We identify advantages and limitations of the framework, and discuss future research on the framework.

  16. Patient safety and infection control: bases for curricular integration.

    Science.gov (United States)

    Silva, Andréa Mara Bernardes da; Bim, Lucas Lazarini; Bim, Felipe Lazarini; Sousa, Alvaro Francisco Lopes; Domingues, Pedro Castania Amadio; Nicolussi, Adriana Cristina; Andrade, Denise de

    2018-05-01

    To analyze curricular integration between teaching of patient safety and good infection prevention and control practices. Integrative review, designed to answer the question: "How does curricular integration of content about 'patient safety teaching' and content about 'infection prevention and control practices' occur in undergraduate courses in the health field?". The following databases were searched for primary studies: CINAHL, LILACS, ScienceDirect, Web of Science, Scopus, Europe PMC and MEDLINE. The final sample consisted of 13 studies. After content analysis, primary studies were grouped into two subject categories: "Innovative teaching practices" and "Curricular evaluation. Patient safety related to infection prevention and control practices is present in the curriculum of health undergraduate courses, but is not coordinated with other themes, is taught sporadically, and focuses mainly on hand hygiene.

  17. Quality control of dosemeters

    International Nuclear Information System (INIS)

    Mendes, L.

    1984-01-01

    Nuclear medicine laboratories are required to assay samples of radioactivity to be administered to patients. Almost universally, these assays are acomplished by use of a well ionization chamber isotope calibrator. The Instituto de Radioprotecao e Dosimetria (Institute for Radiological Protection and Dosimetry) of the Comissao Nacional de Energia Nuclear (National Commission for Nuclear Energy) is carrying out a National Quality Control Programme in Nuclear Medicine, supported by the International Atomic Energy Agency. The assessment of the current needs and practices of quality control in the entire country of Brazil includes Dose Calibrators and Scintilation Cameras, but this manual is restricted to the former. Quality Control Procedures for these Instruments are described in this document together with specific recommendations and assessment of its accuracy. (Author) [pt

  18. Patient safety--worker safety: building a culture of safety to improve healthcare worker and patient well-being.

    Science.gov (United States)

    Yassi, Annalee; Hancock, Tina

    2005-01-01

    Patient safety within the Canadian healthcare system is currently a high national priority, which merits a comprehensive understanding of the underlying causes of adverse events. Not least among these is worker health and safety, which is linked to patient outcomes. Healthcare workers have a high risk of workplace injuries and more mental health problems than most other occupational groups. Many healthcare professionals feel fatigued, stressed, in pain, or at risk of illness or injury-factors they feel impede their ability to provide consistent quality care. With this background, the Occupational Health and Safety Agency for Healthcare (OHSAH) in British Columbia, jointly governed by healthcare unions and healthcare employers, launched several major initiatives to improve the healthcare workplace. These included the promotion of safe patient handling, adaptive clothing, scheduled toileting, stroke management training, measures to improve management of aggressive behaviour and, of course, infection control-all intended to improve the safety of workers, but also to improve patient safety and quality of care. Other projects also explicitly promoting physical and mental health at work, as well as patient safety are also underway. Results of the projects are at various stages of completion, but ample evidence has already been obtained to indicate that looking after the well-being of healthcare workers results in safer and better quality patient care. While more research is needed, our work to date suggests that a comprehensive systems approach to promoting a climate of safety, which includes taking into account workplace organizational factors and physical and psychological hazards for workers, is the best way to improve the healthcare workplace and thereby patient safety.

  19. Krsko NPP Quality Assurance Plan Application to Nuclear Safety Upgrade Projects (PCFV System and PAR System)

    International Nuclear Information System (INIS)

    Biscan, Romeo; Fifnja, Igor

    2014-01-01

    Nuklearna Elektrarna Krsko (NEK) has undertaken Nuclear Safety Upgrade Projects as a safety improvement driven by the lessons learned from the Fukushima-Daiichi Accident. Among other projects, new modification 1008-VA-L Passive Containment Filtered Vent (PCFV) System has been installed which acts as the last barrier minimizing the release of radioactive material into the environment in case of failure of all safety systems, and to insure containment integrity during beyond design basis accidents (BDBA). In addition, modification 1002-GH-L Severe Accident Hydrogen Control System (PAR) has been implemented to prevent and mitigate the consequences of explosive gas generation (hydrogen and carbon monoxide) in case of reactor core melting. To ensure containment integrity for all design basis accidents (DBA) and BDBA conditions, NEK has eliminated existing safety-related electrical recombiners, replaced them with two safety-related passive autocatalytic recombiners (PARs) and added 20 new PARs designed for the BDBA conditions. Krsko NPP Quality Assurance Plan has been applied to Nuclear Safety Upgrade Projects (PCFV System and PAR System) through the following activities: · Internal audit of modification process was performed. · Supplier audits were performed to evaluate QA program efficiency of the main design organization and engineering organizations. · Evaluation and approval of Suppliers were performed. · QA engineer was involved in the review and approval of 1008-VA-L and 1002-GH-L modification documentation (Conceptual Design Package, Design Modification Package, Installation Package, Field Design Change Request, Problem/Deficiency Report, and Final Documentation Package). · Purchasing documentation for modifications 1008-VA-L and 1002-GH-L (technical specifications, purchase orders) has been verified and approved by QA. · QA and QC engineers were involved in oversight of production and testing of the new 1008-VA-L and 1002-GH-L plant components.

  20. Editorial: Advances in healthcare provider and patient training to improve the quality and safety of patient care

    OpenAIRE

    Elizabeth M. Borycki

    2015-01-01

    This special issue of the Knowledge Management & E-Learning: An International Journal is dedicated to describing “Advances in Healthcare Provider and Patient Training to Improve the Quality and Safety of Patient Care.” Patient safety is an important and fundamental requirement of ensuring the quality of patient care. Training and education has been identified as a key to improving healthcare provider patient safety competencies especially when working with new technologies such as electronic ...

  1. Environment, Safety, Health, and Quality Plan for the Buried Waste Integrated Demonstration Program

    International Nuclear Information System (INIS)

    Walker, S.

    1994-05-01

    The Buried Waste Integrated Demonstration (BWID) is a program funded by the US Department of Energy Office of Technology Development. BWID supports the applied research, development, demonstration, testing, and evaluation of a suite of advanced technologies that together form a comprehensive remediation system for the effective and efficient remediation of buried waste. This document describes the Environment, Safety, Health, and Quality requirements for conducting BWID activities at the Idaho National Engineering Laboratory. Topics discussed in this report, as they apply to BWID operations, include Federal, State of Idaho, and Environmental Protection Agency regulations, Health and Safety Plans, Quality Program Plans, Data Quality Objectives, and training and job hazard analysis. Finally, a discussion is given on CERCLA criteria and System and Performance audits as they apply to the BWID Program

  2. Control cards as a statistical quality control resource

    Directory of Open Access Journals (Sweden)

    Aleksandar Živan Drenovac

    2013-02-01

    Full Text Available Normal 0 false false false MicrosoftInternetExplorer4 This paper proves that applying of statistical methods can significantly contribute increasing of products and services quality, as well as increasing of institutions rating. Determining of optimal, apropos anticipatory and limitary values, is based on sample`s statistical analyze. Control cards represent very confident instrument, which is simple for use and efficient for control of process, by which process is maintained in set borders. Thus, control cards can be applied in quality control of procesess of weapons and military equipment production, maintenance of technical systems, as well as for seting of standards and increasing of quality level for many other activities.

  3. Effectiveness of web-based tailored advice on parents' child safety behaviors: randomized controlled trial.

    Science.gov (United States)

    van Beelen, Mirjam Elisabeth Johanna; Beirens, Tinneke Monique Jozef; den Hertog, Paul; van Beeck, Eduard Ferdinand; Raat, Hein

    2014-01-24

    Injuries at home are a major cause of death, disability, and loss of quality of life among young children. Despite current safety education, required safety behavior of parents is often lacking. To prevent various childhood disorders, the application of Web-based tools has increased the effectiveness of health promotion efforts. Therefore, an intervention with Web-based, tailored, safety advice combined with personal counseling (E-Health4Uth home safety) was developed and applied. To evaluate the effect of E-Health4Uth home safety on parents' safety behaviors with regard to the prevention of falls, poisoning, drowning, and burns. A randomized controlled trial was conducted (2009-2011) among parents visiting well-baby clinics in the Netherlands. Parents were randomly assigned to the intervention group (E-Health4Uth home safety intervention) or to the control condition consisting of usual care. Parents in the intervention condition completed a Web-based safety behavior assessment questionnaire; the resulting tailored safety advice was discussed with their child health care professional at a well-baby visit (age approximately 11 months). Parents in the control condition received counseling using generic safety information leaflets at this well-baby visit. Parents' child safety behaviors were derived from self-report questionnaires at baseline (age 7 months) and at follow-up (age 17 months). Each specific safety behavior was classified as safe/unsafe and a total risk score was calculated. Logistic and linear regression analyses were used to reveal differences in safety behavior between the intervention and the control condition at follow-up. A total of 1292 parents (response rate 44.79%) were analyzed. At follow-up, parents in the intervention condition (n=643) showed significantly less unsafe behavior compared to parents in the control condition (n=649): top of staircase (23.91% vs. 32.19%; OR 0.65, 95% CI 0.50-0.85); bottom of staircase (63.53% vs. 71.94%; OR 0

  4. 7 CFR 930.44 - Quality control.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of the...

  5. Assessment of Contributions to Patient Safety Knowledge by the Agency for Healthcare Research and Quality-Funded Patient Safety Projects

    Science.gov (United States)

    Sorbero, Melony E S; Ricci, Karen A; Lovejoy, Susan; Haviland, Amelia M; Smith, Linda; Bradley, Lily A; Hiatt, Liisa; Farley, Donna O

    2009-01-01

    Objective To characterize the activities of projects funded in Agency for Healthcare Research and Quality (AHRQ)' patient safety portfolio and assess their aggregate potential to contribute to knowledge development. Data Sources Information abstracted from proposals for projects funded in AHRQ' patient safety portfolio, information on safety practices from the AHRQ Evidence Report on Patient Safety Practices, and products produced by the projects. Study Design This represented one part of the process evaluation conducted as part of a longitudinal evaluation based on the Context–Input–Process–Product model. Principal Findings The 234 projects funded through AHRQ' patient safety portfolio examined a wide variety of patient safety issues and extended their work beyond the hospital setting to less studied parts of the health care system. Many of the projects implemented and tested practices for which the patient safety evidence report identified a need for additional evidence. The funded projects also generated a substantial body of new patient safety knowledge through a growing number of journal articles and other products. Conclusions The projects funded in AHRQ' patient safety portfolio have the potential to make substantial contributions to the knowledge base on patient safety. The full value of this new knowledge remains to be confirmed through the synthesis of results. PMID:21456108

  6. A Vehicle Active Safety Model: Vehicle Speed Control Based on Driver Vigilance Detection Using Wearable EEG and Sparse Representation.

    Science.gov (United States)

    Zhang, Zutao; Luo, Dianyuan; Rasim, Yagubov; Li, Yanjun; Meng, Guanjun; Xu, Jian; Wang, Chunbai

    2016-02-19

    In this paper, we present a vehicle active safety model for vehicle speed control based on driver vigilance detection using low-cost, comfortable, wearable electroencephalographic (EEG) sensors and sparse representation. The proposed system consists of three main steps, namely wireless wearable EEG collection, driver vigilance detection, and vehicle speed control strategy. First of all, a homemade low-cost comfortable wearable brain-computer interface (BCI) system with eight channels is designed for collecting the driver's EEG signal. Second, wavelet de-noising and down-sample algorithms are utilized to enhance the quality of EEG data, and Fast Fourier Transformation (FFT) is adopted to extract the EEG power spectrum density (PSD). In this step, sparse representation classification combined with k-singular value decomposition (KSVD) is firstly introduced in PSD to estimate the driver's vigilance level. Finally, a novel safety strategy of vehicle speed control, which controls the electronic throttle opening and automatic braking after driver fatigue detection using the above method, is presented to avoid serious collisions and traffic accidents. The simulation and practical testing results demonstrate the feasibility of the vehicle active safety model.

  7. A new radiation safety control system for Ganil

    International Nuclear Information System (INIS)

    Saint Jores, P. De; Luong, T.T.; Martina, L.; Vega, G.

    1991-01-01

    A second generation radiation safety control system has been installed to upgrade the initial system which was not flexible enough to support new ion beams and new experimental conditions required by the accelerator operation. The main reasons which necessitated the improvement of the safety control system are presented. The new system which controls the Ganil accelerator from the first quarter of 1990 is described. It uses a star structured architecture, VME standard processors and front-end modules activated by pDOS operating system and high level language (C and Fortran) tasks, associated with enhanced resolution color displays for real time synoptics. (R.P.) 4 refs., 4 figs

  8. Quality control analysis at the hospital

    International Nuclear Information System (INIS)

    Kristensen, K.

    1979-01-01

    Quality control analysis is an integral part of quality assurance. In a system as with radiopharmaceuticals where part of the finishing of the product takes place at individual hospitals, the need for quality control analysis at the hospital can be discussed. Data are presented that stresses the importance of quality control by the manufacturer as a basis for limitation of such work at hospitals. A simplified programme is proposed

  9. Quality assurance in the procurement of items and services for nuclear power plants

    International Nuclear Information System (INIS)

    1979-01-01

    This Safety Guide was prepared as part of the Agency's programme, referred to as the NUSS programme, for establishing Codes of Practice and Safety Guides relating to nuclear power plants. It supplements the Agency's Code of Practice on Quality Assurance for Safety in Nuclear Power Plants (Safety Series No.50-C-QA), which states requirements for the control of procurement of items and services which are important to the safety of nuclear power plants, for the purpose of achieving quality. The establishment and implementation of controls over the procurement process provide a basis for establishing an appropriate level of confidence that the activities undertaken during procurement of items and services have been performed in accordance with the principles of quality assurance expressed in the Code, and that the required quality of items and services has been achieved. The purchaser, in establishing control over procurement, shall ensure that the quality criteria, quality level, and other quality requirements specified for the particular item or service are taken into account

  10. Evaluating Performance of Safety Management and Occupational Health Using Total Quality Safety Management Model (TQSM

    Directory of Open Access Journals (Sweden)

    E Mohammadfam

    2015-11-01

    Full Text Available Introduction: All organizations, whether public or private, necessitate performance evaluation systems in regard with growth, stability, and development in the competitive fields. One of the existing models for performance evaluation of occupational health and safety management is Total Quality Safety Management model (TQSM. Therefore, the present study aimed to evaluate performance of safety management and occupational health utilizing TQSM model. Methods: In this descriptive-analytic study, the population consisted of 16 individuals, including managers, supervisors, and members of technical protection and work health committee. Then the participants were asked to respond to TQSM questionnaire before and after the implementation of Occupational Health & Safety Advisory Services 18001 (OHSAS18001. Ultimately, the level of each program as well as the TQSM status were determined before and after the implementation of OHSAS18001. Results: The study results showed that the scores obtained by the company before OHSAS 18001’s implementation, was 43.7 out of 312. After implementing OHSAS 18001 in the company and receiving the related certificate, the total score of safety program that company could obtain was 127.12 out of 312 demonstrating a rise of 83.42 scores (26.8%. The paired t-test revealed that mean difference of TQSM scores before and after OHSAS 18001 implementation was proved to be significant (p> 0.05. Conclusion: The study findings demonstrated that TQSM can be regarded as an appropriate model in order to monitor the performance of safety management system and occupational health, since it possesses the ability to quantitatively evaluate the system performance.

  11. Harnessing implementation science to improve care quality and patient safety: a systematic review of targeted literature.

    Science.gov (United States)

    Braithwaite, Jeffrey; Marks, Danielle; Taylor, Natalie

    2014-06-01

    Getting greater levels of evidence into practice is a key problem for health systems, compounded by the volume of research produced. Implementation science aims to improve the adoption and spread of research evidence. A linked problem is how to enhance quality of care and patient safety based on evidence when care settings are complex adaptive systems. Our research question was: according to the implementation science literature, which common implementation factors are associated with improving the quality and safety of care for patients? We conducted a targeted search of key journals to examine implementation science in the quality and safety domain applying PRISMA procedures. Fifty-seven out of 466 references retrieved were considered relevant following the application of exclusion criteria. Included articles were subjected to content analysis. Three reviewers extracted and documented key characteristics of the papers. Grounded theory was used to distil key features of the literature to derive emergent success factors. Eight success factors of implementation emerged: preparing for change, capacity for implementation-people, capacity for implementation-setting, types of implementation, resources, leverage, desirable implementation enabling features, and sustainability. Obstacles in implementation are the mirror image of these: for example, when people fail to prepare, have insufficient capacity for implementation or when the setting is resistant to change, then care quality is at risk, and patient safety can be compromised. This review of key studies in the quality and safety literature discusses the current state-of-play of implementation science applied to these domains. © The Author 2014. Published by Oxford University Press in association with the International Society for Quality in Health Care; all rights reserved.

  12. 14 CFR 21.139 - Quality control.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Quality control. 21.139 Section 21.139... PROCEDURES FOR PRODUCTS AND PARTS Production Certificates § 21.139 Quality control. The applicant must show that he has established and can maintain a quality control system for any product, for which he...

  13. 33 CFR 385.21 - Quality control.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Quality control. 385.21 Section... Processes § 385.21 Quality control. (a) The Corps of Engineers and the non-Federal sponsor shall prepare a quality control plan, in accordance with applicable Corps of Engineers regulations, for each product that...

  14. Evaluating the U.S. Food Safety Modernization Act Produce Safety Rule Standard for Microbial Quality of Agricultural Water for Growing Produce

    NARCIS (Netherlands)

    Havelaar, Arie H; Vazquez, Kathleen M; Topalcengiz, Zeynal; Muñoz-Carpena, Rafael; Danyluk, Michelle D

    2017-01-01

    The U.S. Food and Drug Administration (FDA) has defined standards for the microbial quality of agricultural surface water used for irrigation. According to the FDA produce safety rule (PSR), a microbial water quality profile requires analysis of a minimum of 20 samples for Escherichia coli over 2 to

  15. Patient safety and quality of care: how may clinical simulation contribute?

    DEFF Research Database (Denmark)

    Jensen, Sanne

    2015-01-01

    The usability of health information technology (IT) is increasingly recognized as critically important to the development of systems that ensure patient safety and quality of care. The substantial complexity of organizations, work practice and physical environments within the healthcare sector...... influences the development and application of health IT. When health IT is introduced in local clinical work practices, potential patient safety hazards and insufficient support of work practices need to be examined. Qualitative methods, such as clinical simulation, may be used to evaluate new technology...

  16. [Infection control and safety culture in German hospitals].

    Science.gov (United States)

    Hansen, Sonja; Schwab, Frank; Gropmann, Alexander; Behnke, Michael; Gastmeier, Petra

    2016-07-01

    Healthcare-associated infections (HAI) are the most frequent adverse events in the healthcare setting and their prevention is an important contribution to patient safety in hospitals. To analyse to what extent safety cultural aspects with relevance to infection control are implemented in German hospitals. Safety cultural aspects of infection control were surveyed with an online questionnaire; data were analysed descriptively. Data from 543 hospitals with a median of [IQR] 275 [157; 453] beds were analysed. Almost all hospitals (96.6 %) had internal guidelines for infection control (IC) in place; 82 % defined IC objectives, most often regarding hand hygiene (HH) (93 %) and multidrug resistant organisms (72 %) and less frequently for antibiotic stewardship (48 %) or prevention of specific HAI. In 94 % of hospitals, a reporting system for adverse events was in place, which was also used to report low compliance with HH, outbreaks and Clostridium difficile-associated infections. Members of the IC team were most often seen to hold daily responsibility for IC in the hospital, but rarely other hospital staff (94 versus 19 %). Safety cultural aspects are not fully implemented in German hospitals. IC should be more strongly implemented in healthcare workers' daily routine and more visibly supported by hospital management.

  17. Quality assurance and nuclear power plant safety

    International Nuclear Information System (INIS)

    Mullan, J.V.

    1983-01-01

    Quality assurance in the nuclear industry was born in the late 1960s. Atomic Energy Control Board staff began its regulatory practice on quality assurance during that period. In this presentation the author traces the circumstances that first led to the establishment of Canadian nuclear power plant quality assurance programmes, summarizes progress over the last decade and a half, and outlines the current regulatory approach and what has been learned so far

  18. Related regulation of quality control of industrial products

    International Nuclear Information System (INIS)

    1983-04-01

    This book introduce related regulation of quality control of industrial products, which includes regulations of industrial products quality control, enforcement ordinance of industrial products quality control, enforcement regulation of quality control of industrial products, designated items with industrial production quality indication, industrial production quality test, and industrial production quality test organization and management tips of factory quality by grade.

  19. Assessment of Safety Standards for Automotive Electronic Control Systems

    Science.gov (United States)

    2016-06-01

    This report summarizes the results of a study that assessed and compared six industry and government safety standards relevant to the safety and reliability of automotive electronic control systems. These standards include ISO 26262 (Road Vehicles - ...

  20. Nuclear electric power safety, operation, and control aspects

    CERN Document Server

    Knowles, J Brian

    2013-01-01

    Assesses the engineering of renewable sources for commercial power generation and discusses the safety, operation, and control aspects of nuclear electric power From an expert who advised the European Commission and UK government in the aftermath of Three Mile Island and Chernobyl comes a book that contains experienced engineering assessments of the options for replacing the existing, aged, fossil-fired power stations with renewable, gas-fired, or nuclear plants. From geothermal, solar, and wind to tidal and hydro generation, Nuclear Electric Power: Safety, Operation, and Control Aspects ass

  1. Patient safety and quality improvement education: a cross-sectional study of medical students’ preferences and attitudes

    Directory of Open Access Journals (Sweden)

    Teigland Claire L

    2013-02-01

    Full Text Available Abstract Background Recent educational initiatives by both the World Health Organization and the American Association of Medical Colleges have endorsed integrating teaching of patient safety and quality improvement (QI to medical students. Curriculum development should take into account learners’ attitudes and preferences. We surveyed students to assess preferences and attitudes about QI and patient safety education. Methods An electronic survey was developed through focus groups, literature review, and local expert opinion and distributed via email to all medical students at a single medical school in the spring of 2012. Results A greater proportion of students reported previous exposure to patient safety than to quality improvement topics (79% vs. 47%. More than 80% of students thought patient safety was of the same or greater importance than basic science or clinical skills whereas quality improvement was rated as the same or more important by about 70% of students. Students rated real life examples of quality improvement projects and participation in these projects with actual patients as potentially the most helpful (mean scores 4.2/5 and 3.9/5 respectively. For learning about patient safety, real life examples of mistakes were again rated most highly (mean scores 4.5/5 for MD presented mistakes and 4.1/5 for patient presented mistakes. Students rated QI as very important to their future career regardless of intended specialty (mean score 4.5/5. Conclusions Teaching of patient safety and quality improvement to medical students will be best received if it is integrated into clinical education rather than solely taught in pre-clinical lectures or through independent computer modules. Students recognize that these topics are important to their careers as future physicians regardless of intended specialty.

  2. Some safety considerations in laser-controlled thermonuclear reactors. Final report

    International Nuclear Information System (INIS)

    Botts, T.E.; Breton, D.; Chan, C.K.; Levy, S.I.; Sehnert, M.; Ullman, A.Z.

    1978-07-01

    A major objective of this study was to identify potential safety questions for laser controlled thermonuclear reactors. From the safety viewpoint, it does not appear that the actual laser controlled thermonuclear reactor conceptual designs present hazards very different than those of magnetically confined fusion reactors. Some aspects seem beneficial, such as small lithium inventories, and the absence of cryogenic devices, while other aspects are new, for example the explosion of pressure vessels and laser hazards themselves. Major aspects considered in this report include: (a) general safety considerations, (b) tritium inventories, (c) system behavior during loss of flow accidents, and (d) safety considerations of laser related penetrations

  3. Code of practice on quality assurance for safety in nuclear power plants

    International Nuclear Information System (INIS)

    1988-01-01

    The code sets forth the management principles and objectives to be met during the implementation of activities in different phases of the nuclear power plants (NPPs) for assuring safety. It is intended for use by organisations and individuals responsible for safety related functions in design, manufacturing, construction, commissioning, operation and decommissioning of NPPs. It covers the functions of management, performance, verification and corrective action. It also deals with the quality assurance records. (M.G.B.)

  4. Food safety and quality management in Kenya: An overview of the ...

    African Journals Online (AJOL)

    Food safety and quality management in Kenya: An overview of the roles ... of the enormous informal sector in the food industry accounting for at least 80% of the ... management in the food supply chain has cost implications and income is a ...

  5. Patient safety is not enough: targeting quality improvements to optimize the health of the population.

    Science.gov (United States)

    Woolf, Steven H

    2004-01-06

    Ensuring patient safety is essential for better health care, but preoccupation with niches of medicine, such as patient safety, can inadvertently compromise outcomes if it distracts from other problems that pose a greater threat to health. The greatest benefit for the population comes from a comprehensive view of population needs and making improvements in proportion with their potential effect on public health; anything less subjects an excess of people to morbidity and death. Patient safety, in context, is a subset of health problems affecting Americans. Safety is a subcategory of medical errors, which also includes mistakes in health promotion and chronic disease management that cost lives but do not affect "safety." These errors are a subset of lapses in quality, which result not only from errors but also from systemic problems, such as lack of access, inequity, and flawed system designs. Lapses in quality are a subset of deficient caring, which encompasses gaps in therapeutics, respect, and compassion that are undetected by normative quality indicators. These larger problems arguably cost hundreds of thousands more lives than do lapses in safety, and the system redesigns to correct them should receive proportionately greater emphasis. Ensuring such rational prioritization requires policy and medical leaders to eschew parochialism and take a global perspective in gauging health problems. The public's well-being requires policymakers to view the system as a whole and consider the potential effect on overall population health when prioritizing care improvements and system redesigns.

  6. Quality control as a way to find out doses as low as reasonably practicable in mammography systems

    International Nuclear Information System (INIS)

    Hwang, S.F.; Nogueira, M.S.; Peixoto, J.E.; Paraguay, Y.V.

    2008-01-01

    The breast cancer is the most common neoplasm amongst women. Mammography is an essential tool for diagnosis and early detection of this disease. In order to guarantee the effectiveness of the diagnosis taking into account the patient radiation safety, it is mandatory to perform the quality control tests of the mammographic equipment. The main objective of this work has been to evaluate the relationship between the image quality and the total performance of the medical equipment. Primary data were collected from several radiological facilities during the quality control inspections performed by the local regulatory authorities of the Brazilian health, the National Commission of Nuclear Energy and the Brazilian College of Radiology. The main important functioning parameters were evaluated as well as the image quality using the simulator 'phantom mama'. In spite of the fact that high quality images could suggest delivering large radiation doses to patients it has been demonstrated that it is possible to acquire images with a good quality for clinical diagnosis without delivering high doses if the system is working properly. It has been concluded that following an optimized quality control program could avoid the complex dosimetric studies to guarantee good images quality. (author)

  7. Quality control of 5mg diazepam suppositories manipulated in the city of Campos Goytacazes – RJ

    Directory of Open Access Journals (Sweden)

    Renata Aparecida Venturi Canzian

    2012-10-01

    Full Text Available Diazepam suppositories are widely used by children and elderly, and require close attention to quality control because it is a controlled prescription drug. The objective of the study was to analyze diazepam suppositories manipulated in Campos dos Goytacazes, RJ, to verify if they are within the required quality standards, and offer safety and efficiency to patients. We analyzed samples of 5mg diazepam suppositories acquired in five randomly selected pharmacies, identified as Pharmacy A, Pharmacy B, Pharmacy C, Pharmacy D, and Pharmacy E. We ran tests on average weight, organoleptic control, hardness, melting point, and dissolution. Data was analyzed and compared with the requirements of the Brazilian Pharmacopoeia. This analysis was made over a table in Excel. We conclude that only C Pharmacy was approved in all tests, and this is the only laboratory that has analyzed the quality of the product warranty. Laboratories A, B, D and E have been approved in some tests, and failed one or more tests. To ensure quality control, suppositories needed to pass in all tests, which was not the case of these labs. Therefore, we recommended the following procedures to the investigated laboratories: changes in packaging, greater precision in handling, quality control prior to dispensing the product, and efficient pharmaceutical care service.

  8. Quality factors quantification/assurance for software related to safety in nuclear power plants

    International Nuclear Information System (INIS)

    Nunez McLeod, J.E.; Rivera, S.S.

    1997-01-01

    Quality assurance plan is needed to guarantee the software quality. The use of such a plan involves activities that should take place all along the life cycle, and which can be evaluated using the so called quality factors. This is due to the fact that the quality itself cannot be measured, but some of its manifestations can be used for this purpose. In the present work, a methodology to quantify a set of quality factors is proposed, for software based systems to be used in safety related areas in nuclear power plants. (author) [es

  9. Assessment of Quality and Safety of Street-vended Fried West ...

    African Journals Online (AJOL)

    This study was carried out to assess the quality and safety of street-vended fried West African ilisha (Ilisha africana) from major markets in Ibadan, Oyo State, Nigeria. A total number of 100 fried fish samples obtained from ten major markets in Ibadan, Oyo State, Nigeria were analysed in the laboratory for: proximate ...

  10. The Trends and their Impact on Fishery Products Safety and Quality

    Directory of Open Access Journals (Sweden)

    Gheorghe Adrian ZUGRAVU

    2012-11-01

    Full Text Available The paper follows two main objectives: to understand consumers’ perception of safety and quality of fishery products and to identify communication levers in order to improve the perceived image of fishery products. The present research is focused on the fishery products, regardless of their presentation – fresh, frozen or processed. This paper conducted a questionnaire survey of Romanian consumers’ perception toward fishery products. The empirical study with brands indicated that consumers are different awareness to domestic and foreign safety fish products. National fishery products got more attention from the consumers.

  11. A proposal of safety indicators aggregation to assess the safety management effectiveness of nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Jose Antonio B.; Saldanha, Pedro L.C. [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil). Coordenacao-Geral de Reatores e Ciclo Combustivel], e-mail: jantonio@cnen.gov.br, e-mail: saldanha@cnen.gov.br; Melo, Paulo F.F. Frutuoso e [Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear], e-mail: frutuoso@con.ufrj.br

    2009-07-01

    Safety management has changed with the evolution of management methods, named Quality Systems, moving from Quality Control, where the focus was the product, passing through Quality Assurance, which takes care of the whole manufacturing process and reaching the Total Quality Management, where policies and goals are established. Nowadays, there is a trend towards Management Systems, which integrate all different aspects related to the management of an organization (safety, environment, security, quality, costs and, etc), but it is necessary to have features to establish and assure that safety overrides the remaining aspects. The most usual way to reach this goal is to establish a policy where safety is a priority, but its implementation and the assessment of its effectiveness are no so simple. Nuclear power plants usually have over a hundred safety indicators in many processes dedicated to prevent and detect problems, although a lot of them do not evaluate these indicators in an integrated manner or point out degradation trends of organizational aspects, which can affect the plant safety. This work develops an aggregation of proactive and reactive safety indicators in order to evaluate the effectiveness of nuclear power plant safety management and to detect, at early stages, signs of process degradation or activities used to establish, maintain and assure safety conditions. The aggregation integrates indicators of the usual processes and is based on the manner the management activities have been developed in the last decades, that is: Planning, Doing, Checking and Acting - known as PDCA cycle - plus a fifth element related to the capability of those who perform safety activities. The proposed aggregation is in accordance to Brazilian standards and international recommendations and constitutes a friendly link between the top management level and the daily aspects of the organization. (author)

  12. A proposal of safety indicators aggregation to assess the safety management effectiveness of nuclear power plants

    International Nuclear Information System (INIS)

    Carvalho, Jose Antonio B.; Saldanha, Pedro L.C.; Melo, Paulo F.F. Frutuoso e

    2009-01-01

    Safety management has changed with the evolution of management methods, named Quality Systems, moving from Quality Control, where the focus was the product, passing through Quality Assurance, which takes care of the whole manufacturing process and reaching the Total Quality Management, where policies and goals are established. Nowadays, there is a trend towards Management Systems, which integrate all different aspects related to the management of an organization (safety, environment, security, quality, costs and, etc), but it is necessary to have features to establish and assure that safety overrides the remaining aspects. The most usual way to reach this goal is to establish a policy where safety is a priority, but its implementation and the assessment of its effectiveness are no so simple. Nuclear power plants usually have over a hundred safety indicators in many processes dedicated to prevent and detect problems, although a lot of them do not evaluate these indicators in an integrated manner or point out degradation trends of organizational aspects, which can affect the plant safety. This work develops an aggregation of proactive and reactive safety indicators in order to evaluate the effectiveness of nuclear power plant safety management and to detect, at early stages, signs of process degradation or activities used to establish, maintain and assure safety conditions. The aggregation integrates indicators of the usual processes and is based on the manner the management activities have been developed in the last decades, that is: Planning, Doing, Checking and Acting - known as PDCA cycle - plus a fifth element related to the capability of those who perform safety activities. The proposed aggregation is in accordance to Brazilian standards and international recommendations and constitutes a friendly link between the top management level and the daily aspects of the organization. (author)

  13. Safety management of software-based equipment

    CERN Document Server

    Boulanger, Jean-Louis

    2013-01-01

    A review of the principles of the safety of software-based equipment, this book begins by presenting the definition principles of safety objectives. It then moves on to show how it is possible to define a safety architecture (including redundancy, diversification, error-detection techniques) on the basis of safety objectives and how to identify objectives related to software programs. From software objectives, the authors present the different safety techniques (fault detection, redundancy and quality control). "Certifiable system" aspects are taken into account throughout the book. C

  14. Quality and reliability control on assemblies

    International Nuclear Information System (INIS)

    Mueller, H.

    1976-01-01

    Taking as an example electronic assemblies in printed circuit board engineering, quality control during manufacture is dealt with. After giving a survey of four phases of quality and reliability control, some specific methods of quality control are dealt with by means of a flowchart, and by some examples the necessity and the success of these measures are shown. (RW) [de

  15. [Quality of care and safety indicators in anticoagulated patients with non-valvular auricular fibrillation and deep venous thromboembolic disease].

    Science.gov (United States)

    Ignacio, E; Mira, J J; Campos, F J; López de Sá, E; Lorenzo, A; Caballero, F

    2018-03-19

    To identify and prioritise indicators to assess the quality of care and safety of patients with non-valvular auricular fibrillation (NVAF) and deep vein thrombosis (DVT) treated with anticoagulants. Using the consensus conference technique, a group of professionals and clinical experts, the determining factors of the NVAF and DVT care process were identified, in order to define the quality and safety criteria. A proposal was made for indicators of quality and safety that were prioritised, taking into account a series of pre-established attributes. The selected indicators were classified into indicators of context, safety, action, and outcomes of the intervention in the patient. A set of 114 health care and safety quality indicators were identified, of which 35 were prioritised: 15 for NVAF and 20 for DVT. About half (49%) of the indicators (40% for NVAF and 55% for DVT) applied to patient safety, and 26% (33% for NVAF and 20% for DVT) to the outcomes of interventions in the patient. The present work presents a set of agreed indicators by a group of expert professionals that can contribute to the improvement of the quality of care of patients with NVAF and DVT treated with anticoagulants. Copyright © 2018 SECA. Publicado por Elsevier España, S.L.U. All rights reserved.

  16. Quality Control in Mammography: Image Quality and Patient Doses

    International Nuclear Information System (INIS)

    Ciraj Bjelac, O.; Arandjic, D.; Boris Loncar, B.; Kosutic, D.

    2008-01-01

    Mammography is method of choice for early detection of breast cancer. The purpose of this paper is preliminary evaluation the mammography practice in Serbia, in terms of both quality control indicators, i.e. image quality and patient doses. The survey demonstrated considerable variations in technical parameters that affect image quality and patients doses. Mean glandular doses ranged from 0.12 to 2.8 mGy, while reference optical density ranged from 1.2 to 2.8. Correlation between image contrast and mean glandular doses was demonstrated. Systematic implementation of quality control protocol should provide satisfactory performance of mammography units and maintain satisfactory image quality and keep patient doses as low as reasonably practicable. (author)

  17. Improving elementary school quality through the use of a social-emotional and character development program: a matched-pair, cluster-randomized, controlled trial in Hawai'i.

    Science.gov (United States)

    Snyder, Frank J; Vuchinich, Samuel; Acock, Alan; Washburn, Isaac J; Flay, Brian R

    2012-01-01

    School safety and quality affect student learning and success. This study examined the effects of a comprehensive elementary school-wide social-emotional and character education program, Positive Action, on teacher, parent, and student perceptions of school safety and quality utilizing a matched-pair, cluster-randomized, controlled design. The Positive Action Hawai'i trial included 20 racially/ethnically diverse schools and was conducted from 2002-2003 through 2005-2006. School-level archival data, collected by the Hawai'i Department of Education, were used to examine program effects at 1-year post-trial. Teacher, parent, and student data were analyzed to examine indicators of school quality such as student safety and well-being, involvement, and satisfaction, as well as overall school quality. Matched-paired t-tests were used for the primary analysis, and sensitivity analyses included permutation tests and random-intercept growth curve models. Analyses comparing change from baseline to 1-year post-trial revealed that intervention schools demonstrated significantly improved school quality compared to control schools, with 21%, 13%, and 16% better overall school quality scores as reported by teachers, parents, and students, respectively. Teacher, parent, and student reports on individual school-quality indicators showed improvement in student safety and well-being, involvement, satisfaction, quality student support, focused and sustained action, standards-based learning, professionalism and system capacity, and coordinated team work. Teacher reports also showed an improvement in the responsiveness of the system. School quality was substantially improved, providing evidence that a school-wide social-emotional and character education program can enhance school quality and facilitate whole-school change. © 2011, American School Health Association.

  18. Optimizing Quality of Care and Patient Safety in Malaysia: The Current Global Initiatives, Gaps and Suggested Solutions

    OpenAIRE

    Jarrar, Mu?taman; Rahman, Hamzah Abdul; Don, Mohammad Sobri

    2015-01-01

    Background and Objective: Demand for health care service has significantly increased, while the quality of healthcare and patient safety has become national and international priorities. This paper aims to identify the gaps and the current initiatives for optimizing the quality of care and patient safety in Malaysia. Design: Review of the current literature. Highly cited articles were used as the basis to retrieve and review the current initiatives for optimizing the quality of care and patie...

  19. VGI QUALITY CONTROL

    Directory of Open Access Journals (Sweden)

    C. C. Fonte

    2015-08-01

    Full Text Available This paper presents a framework for considering quality control of volunteered geographic information (VGI. Different issues need to be considered during the conception, acquisition and post-acquisition phases of VGI creation. This includes items such as collecting metadata on the volunteer, providing suitable training, giving corrective feedback during the mapping process and use of control data, among others. Two examples of VGI data collection are then considered with respect to this quality control framework, i.e. VGI data collection by National Mapping Agencies and by the most recent Geo-Wiki tool, a game called Cropland Capture. Although good practices are beginning to emerge, there is still the need for the development and sharing of best practice, especially if VGI is to be integrated with authoritative map products or used for calibration and/or validation of land cover in the future.

  20. Quality assurance guidance for TRUPACT-II [Transuranic Package Transporter-II] payload control

    International Nuclear Information System (INIS)

    1989-10-01

    The Transuranic Package Transporter-II (TRUPACT-II) Safety Analysis Report for Packaging (SARP) approved by the Nuclear Regulatory Commission (NRC), discusses authorized methods for payload control in Appendix 1.3.7 and the Quality Assurance (QA) requirements in Section 9.3. Subsection 9.3.2.1 covers maintenance and use of the TRUPACT-II and the specific QA requirements are given in DOE/WIPP 89-012. Subsection 9.3.2.2 covers payload compliance, for which this document was written. 6 refs

  1. Revision: quality control of 99mTc

    International Nuclear Information System (INIS)

    Alves, S.M.; Kabad, M.C.; Teixeira, G.J.; Sousa, C H.S.

    2015-01-01

    The radiopharmaceutical most commonly used in nuclear medicine is technetium-99m. Radiopharmaceuticals labeled with 99m Tc are the main agents for diagnosis, being used in the vast majority of procedures due to radionuclide characteristics. During its preparation impurities can be generated that make products with different qualities of the desired. In this paper were presented some of the factors that can interfere with radiopharmaceuticals and the tests used for quality assurance, certifying that the product is fit for purpose. It is up to nuclear medicine centers deploy a program to raise the quality of exams and increase patient safety. (author)

  2. 7 CFR 58.928 - Quality control tests.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be...

  3. Expert database system for quality control

    Science.gov (United States)

    Wang, Anne J.; Li, Zhi-Cheng

    1993-09-01

    There are more competitors today. Markets are not homogeneous they are fragmented into increasingly focused niches requiring greater flexibility in the product mix shorter manufacturing production runs and above allhigher quality. In this paper the author identified a real-time expert system as a way to improve plantwide quality management. The quality control expert database system (QCEDS) by integrating knowledge of experts in operations quality management and computer systems use all information relevant to quality managementfacts as well as rulesto determine if a product meets quality standards. Keywords: expert system quality control data base

  4. Guidebook on quality control of water reactor fuel

    International Nuclear Information System (INIS)

    1983-01-01

    As a result of the increasing contribution of nuclear power to the world's supply of electrical energy, growing emphasis is being placed on the reliability of nuclear fuel performance. The need to produce a reliable product is based not only on economic reasons but also on safety considerations. Fuel assemblies must withstand the operational requirements placed on them while in the reactor; also, in some cases, they have to be stored for long periods in water-filled basins until they are either reprocessed or ultimately subjected to disposal. One of the keys to consistent and reliable fuel production is an adequate Quality Control (QC) programme, operating under a Quality Assurance (QA) system. In connection with various activities sponsored by the International Atomic Energy Agency it has been suggested for some time that a guidebook should be published, highlighting the role that QC plays in the manufacture of nuclear fuel and stressing the relationship that exists between the QC and QA functions. The aim of this book is to give a summary of the present state of practical experience in the areas of: quality-relevant design requirements; quality control of products and processes. Specific QA requirements are referred to where they are important for an understanding of the co-operation required between the various activities involved in nuclear fuel technology. Examples are also given to illustrate specific needs or specific types of experience in this area. In order to distinguish clearly between the generally required criteria and rules and the details of particular practical experience, the book is divided into two main parts. Part A focuses on the philosophy and principles; Part B supplements Part A with technically detailed descriptions and examples

  5. Automated safety control by video cameras

    NARCIS (Netherlands)

    Lefter, I.; Rothkrantz, L.; Somhorst, M.

    2012-01-01

    At this moment many surveillance systems are installed in public domains to control the safety of people and properties. They are constantly watched by human operators who are easily overloaded. To support the human operators, a surveillance system model is designed that detects suspicious behaviour

  6. Positioning Continuing Education: Boundaries and Intersections between the Domains Continuing Education, Knowledge Translation, Patient Safety and Quality Improvement

    Science.gov (United States)

    Kitto, Simon; Bell, Mary; Peller, Jennifer; Sargeant, Joan; Etchells, Edward; Reeves, Scott; Silver, Ivan

    2013-01-01

    Public and professional concern about health care quality, safety and efficiency is growing. Continuing education, knowledge translation, patient safety and quality improvement have made concerted efforts to address these issues. However, a coordinated and integrated effort across these domains is lacking. This article explores and discusses the…

  7. 7 CFR 58.335 - Quality control tests.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Quality control tests. 58.335 Section 58.335... Procedures § 58.335 Quality control tests. All milk, cream and related products are subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow...

  8. Bulk H analysis using neutrons for routine quality control of cassava and products

    International Nuclear Information System (INIS)

    Jonah, S.A.; Okunade, I.O.; Abolude, O.; Onyike, E.; Inuwa, I.M.

    2011-01-01

    Nuclear and related techniques are useful in addressing the issues of food security and safety facing the world today, via quality control of raw materials and products. In this work, experimental investigations were performed to assess the use of total hydrogen content in cassava and products as a quality control indicator of starch and cyanide contents. The work was carried out using a neutron reflection facility at the Centre for Energy Research and Training, Ahmadu Bello University, Zaria, Nigeria. Cassava samples and products were obtained from retail outlets of Ibadan, Umudike and Zaria, representing three major regions of Nigeria. In general, data obtained indicate a total hydrogen content range of 4.47±0.11-10.71±0.27 wt% for the various samples, including raw, dry and processed cassava. Results show that samples having low hydrogen content are generally rich in cyanide compounds and demonstrate an inverse relationship between hydrogen content and cyanide content. The implication of this is that the neutron reflection facility can be used as a quality control setup for routine determination of hydrogen as an indicator of the cyanide content in cassava and products.

  9. Design and research of safety monitor and control system based on CAN BUS

    International Nuclear Information System (INIS)

    Wen Xinling; Chen Yu; Zhang Zhen; Zhao Yubin

    2007-01-01

    In Order to protect machine operator under danger work area in producing-manufacturing industry, we present a distributed safety monitor and control system based on CAN BUS technology. The detection signal is collected based on the photo-voltage characteristics of the infrared sensor and it was processed with the core of AT89C51. The microprocessor controls the CAN BUS controller SJA1000/transceiver PCA82C250 to structure CAN BUS communication system to transmit the data. Through the serial interface MAX232 connected main controller with each control node, PC can monitor and control each machine in real time and renew control scheme. This paper introduces composition principle and the methods of hardware design in detail. Experiments shown that the system has yield control precision of 0.1 mm, defend distance more than 15 m and the measurement accuracy of 100%. Moreover, it can realize to reform FA431 and monitor cotton-breaking, yarn-breaking and product quality. Productivity is improved about 25%-35%. (authors)

  10. Quality control of radiopharmaceuticals

    International Nuclear Information System (INIS)

    Verdera, E.S.

    1994-01-01

    The quality control of radiopharmaceuticals is based in physics, physics-chemical and biological controls. Between the different controls can be enumerated the following: visual aspect,side, number of particle beams,activity,purity,ph,isotonicity,sterility,radioinmunoessay,toxicity,stability and clinical essay

  11. The Qualification Experiences for Safety-critical Software of POSAFE-Q

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jang Yeol; Son, Kwang Seop; Cheon, Se Woo; Lee, Jang Soo; Kwon, Kee Choon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2009-05-15

    Programmable Logic Controllers (PLC) have been applied to the Reactor Protection System (RPS) and the Engineered Safety Feature (ESF)-Component Control System (CCS) as the major safety system components of nuclear power plants. This paper describes experiences on the qualification of the safety-critical software including the pCOS kernel and system tasks related to a safety-grade PLC, i.e. the works done for the Software Verification and Validation, Software Safety Analysis, Software Quality Assurance, and Software Configuration Management etc.

  12. Quality and safety based management of radiological and clinical equipment

    International Nuclear Information System (INIS)

    Arora, S.; Saini, P.S.

    2001-01-01

    TQM (Total quality management) is the 'buzz' acronym expected in almost every aspect of industrial manufacturing, product development and services solicited by the outside agencies. The correct management of the many technological resources in health institutions in terms of efficiency, effectiveness and safety is a necessity in view of the criteria on which modern medicine is based. Almost all activities -be they diagnostic, therapeutic and rehabilitative - carried out within a modern hospital are based on widespread application of equipment and technology, the efficiency of which can directly influence the quality of service offered to the patient

  13. Good safety culture maintenance at Leningrad nuclear power plant

    International Nuclear Information System (INIS)

    Ardanov, A.

    1996-01-01

    The evidence in favour of the Leningrad NPP commitment to safety tasks, as the case is in the international practice, is The Safety Policy Statement document where safety is declared to be more significant than the power generation related issues, with the entire responsibility for the safety provision taken over by the operating utility. To avoid the situation when the stated safety tasks and policy remain only a declaration, the organizational structure of the operating utility was expanded to include The Safety Control Department and The Quality Control Department whose tasks encompass the control of the achieved safety level, development of recommendations, measures and actions aimed at the safety culture improvement, assessment and revision of the criteria and requirements to the personnel and management. Each individual at LNPP whose activity affects the plant safety has been familiarized with The Safety Policy Statement document

  14. Good safety culture maintenance at Leningrad nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Ardanov, A [Safety Control Dept., Leningrad Nuclear Power Plant, Leningrad (Russian Federation)

    1997-12-31

    The evidence in favour of the Leningrad NPP commitment to safety tasks, as the case is in the international practice, is The Safety Policy Statement document where safety is declared to be more significant than the power generation related issues, with the entire responsibility for the safety provision taken over by the operating utility. To avoid the situation when the stated safety tasks and policy remain only a declaration, the organizational structure of the operating utility was expanded to include The Safety Control Department and The Quality Control Department whose tasks encompass the control of the achieved safety level, development of recommendations, measures and actions aimed at the safety culture improvement, assessment and revision of the criteria and requirements to the personnel and management. Each individual at LNPP whose activity affects the plant safety has been familiarized with The Safety Policy Statement document.

  15. 7 CFR 58.642 - Quality control tests.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Quality control tests. 58.642 Section 58.642... Procedures § 58.642 Quality control tests. All mix ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow line samples as...

  16. Control of Nuclear Materials and Special Equipment (Nuclear Safety Regulations)

    International Nuclear Information System (INIS)

    Cizmek, A.; Prah, M.; Medakovic, S.; Ilijas, B.

    2008-01-01

    Based on Nuclear Safety Act (OG 173/03) the State Office for Nuclear Safety (SONS) in 2008 adopted beside Ordinance on performing nuclear activities (OG 74/06) and Ordinance on special conditions for individual activities to be performed by expert organizations which perform activities in the area of nuclear safety (OG 74/06) the new Ordinance on the control of nuclear material and special equipment (OG 15/08). Ordinance on the control of nuclear material and special equipment lays down the list of nuclear materials and special equipment as well as of nuclear activities covered by the system of control of production of special equipment and non-nuclear material, the procedure for notifying the intention to and filing the application for a license to carry out nuclear activities, and the format and contents of the forms for doing so. This Ordinance also lays down the manner in which nuclear material records have to be kept, the procedure for notifying the State administration organization (regulatory body) responsible for nuclear safety by the nuclear material user, and the keeping of registers of nuclear activities, nuclear material and special equipment by the State administration organization (regulatory body) responsible for nuclear safety, as well as the form and content of official nuclear safety inspector identification card and badge.(author)

  17. Quality control of nuclear medicine instrumentation

    International Nuclear Information System (INIS)

    Mould, R.F.

    1983-09-01

    The proceedings of a conference held by the Hospital Physicists' Association in London 1983 on the quality control of nuclear medicine instrumentation are presented. Section I deals with the performance of the Anger gamma camera including assessment during manufacture, acceptance testing, routine testing and long-term assessment of results. Section II covers interfaces, computers, the quality control problems of emission tomography and the quality of software. Section III deals with radionuclide measurement and impurity assessment and Section IV the presentation of images and the control of image quality. (U.K.)

  18. Safety Metrics for Human-Computer Controlled Systems

    Science.gov (United States)

    Leveson, Nancy G; Hatanaka, Iwao

    2000-01-01

    The rapid growth of computer technology and innovation has played a significant role in the rise of computer automation of human tasks in modem production systems across all industries. Although the rationale for automation has been to eliminate "human error" or to relieve humans from manual repetitive tasks, various computer-related hazards and accidents have emerged as a direct result of increased system complexity attributed to computer automation. The risk assessment techniques utilized for electromechanical systems are not suitable for today's software-intensive systems or complex human-computer controlled systems.This thesis will propose a new systemic model-based framework for analyzing risk in safety-critical systems where both computers and humans are controlling safety-critical functions. A new systems accident model will be developed based upon modem systems theory and human cognitive processes to better characterize system accidents, the role of human operators, and the influence of software in its direct control of significant system functions Better risk assessments will then be achievable through the application of this new framework to complex human-computer controlled systems.

  19. A cross-sectional study to identify organisational processes associated with nurse-reported quality and patient safety

    Science.gov (United States)

    Tvedt, Christine; Sjetne, Ingeborg Strømseng; Helgeland, Jon; Bukholm, Geir

    2012-01-01

    Objectives The purpose of this study was to identify organisational processes and structures that are associated with nurse-reported patient safety and quality of nursing. Design This is an observational cross-sectional study using survey methods. Setting Respondents from 31 Norwegian hospitals with more than 85 beds were included in the survey. Participants All registered nurses working in direct patient care in a position of 20% or more were invited to answer the survey. In this study, 3618 nurses from surgical and medical wards responded (response rate 58.9). Nurses' practice environment was defined as organisational processes and measured by the Nursing Work Index Revised and items from Hospital Survey on Patient Safety Culture. Outcome measures Nurses' assessments of patient safety, quality of nursing, confidence in how their patients manage after discharge and frequency of adverse events were used as outcome measures. Results Quality system, nurse–physician relation, patient safety management and staff adequacy were process measures associated with nurse-reported work-related and patient-related outcomes, but we found no associations with nurse participation, education and career and ward leadership. Most organisational structures were non-significant in the multilevel model except for nurses’ affiliations to medical department and hospital type. Conclusions Organisational structures may have minor impact on how nurses perceive work-related and patient-related outcomes, but the findings in this study indicate that there is a considerable potential to address organisational design in improvement of patient safety and quality of care. PMID:23263021

  20. Safety aspects of core power distribution surveillance and control

    International Nuclear Information System (INIS)

    Beraha, D.; Grumbach, R.; Hoeld, A.; Werner, W.

    1978-01-01

    The incentives for improved core surveillance and core control systems are outlined. An efficient code for evaluating the power distribution is indispensable for designing and testing such a system. The characteristics of the core simulator QUABOX/CUBBOX and the features required for off-line and on-line applications are described. The important role of the simulator for the safety assessment of a digital core control system is underlined. With regard to the safety aspects of core control, possible disturbances are classified. Simulation results are given concerning the failure of a control actuator. It is shown that means can be devised to prevent unstable behaviour of the control system and, furthermore, to contribute to a safe reactor operation by accounting for process disturbances. (author)

  1. Control by quality: proposition of a typology.

    Science.gov (United States)

    Pujo, P; Pillet, M

    The application of Quality tools and methods in industrial management has always had a fundamental impact on the control of production. It influences the behavior of the actors concerned, while introducing the necessary notions and formalizations, especially for production systems with little or no automation, which constitute a large part of the industrial activity. Several quality approaches are applied in the workshop and are implemented at the level of the control. In this paper, the authors present a typology of the various approaches that have successively influenced control, such as statistical process control, quality assurance, and continuous improvement. First the authors present a parallel between production control and quality organizational structure. They note the duality between control, which is aimed at increasing productivity, and quality, which aims to satisfy the needs of the customer. They also note the hierarchical organizational structure of these two systems of management with, at each level, the notion of a feedback loop. This notion is fundamental to any kind of decision making. The paper is organized around the operational, tactical, and strategic levels, by describing for each level the main methods and tools for control by quality. The overview of these tools and methods starts at the operational level, with the Statistical Process Control, the Taguchi technique, and the "six sigma" approach. On the tactical level, we find a quality system approach, with a documented description of the procedures introduced in the firm. The management system can refer here to Quality Assurance, Total Productive Maintenance, or Management by Total Quality. The formalization through procedures of the rules of decision governing the process control enhances the validity of these rules. This leads to the enhancement of their reliability and to their consolidation. All this counterbalances the human, intrinsically fluctuating, behavior of the control

  2. INFORMATION SYSTEM QUALITY CONTROL KNOWLEDGE

    Directory of Open Access Journals (Sweden)

    Vladimir Nikolaevich Babeshko

    2017-02-01

    Full Text Available The development of the educational system is associated with the need to control the quality of educational services. Quality control knowledge is an important part of the scientific process. The penetration of computers into all areas of activities changing approaches and technologies that previously they were used.

  3. A Vehicle Active Safety Model: Vehicle Speed Control Based on Driver Vigilance Detection Using Wearable EEG and Sparse Representation

    Directory of Open Access Journals (Sweden)

    Zutao Zhang

    2016-02-01

    Full Text Available In this paper, we present a vehicle active safety model for vehicle speed control based on driver vigilance detection using low-cost, comfortable, wearable electroencephalographic (EEG sensors and sparse representation. The proposed system consists of three main steps, namely wireless wearable EEG collection, driver vigilance detection, and vehicle speed control strategy. First of all, a homemade low-cost comfortable wearable brain-computer interface (BCI system with eight channels is designed for collecting the driver’s EEG signal. Second, wavelet de-noising and down-sample algorithms are utilized to enhance the quality of EEG data, and Fast Fourier Transformation (FFT is adopted to extract the EEG power spectrum density (PSD. In this step, sparse representation classification combined with k-singular value decomposition (KSVD is firstly introduced in PSD to estimate the driver’s vigilance level. Finally, a novel safety strategy of vehicle speed control, which controls the electronic throttle opening and automatic braking after driver fatigue detection using the above method, is presented to avoid serious collisions and traffic accidents. The simulation and practical testing results demonstrate the feasibility of the vehicle active safety model.

  4. Quality and Safety of Home ICP Monitoring Compared with In-Hospital Monitoring

    DEFF Research Database (Denmark)

    Andresen, Morten; Juhler, Marianne; Munch, Tina Nørgaard

    2012-01-01

    Introduction: Intracranial pressure (ICP) monitoring is usually conducted in-hospital using stationary devices. Modern mobile ICP monitoring systems present new monitoring possibilities more closely following the patients' daily life. We reviewed patient safety, quality of technical data...

  5. Investigation of radiation safety and safety culture of medical sanitation vocation in Suzhou

    International Nuclear Information System (INIS)

    Tang Bo; Tu Yu; Zhang Yin

    2009-01-01

    Objective: To investigate the construction of radiation safety and safety culture of medical sanitation vocation in Suzhou. Methods: All medical units registered in administration center of Suzhou were included. The above selected medical units were completely investigated, district and county under the same condition of quality control. Results: The radiation safety and safety culture are existing differences among different property and grade hospitals of medicai sanitation vocation in Suzhou. Conclusion: The construction of radiation safety and safety culture is generally occupying in good level in suhzou, but there are obvious differences among different property and grade hospitals. The main reason for the differences in the importance attached to by the hospital decision-making and department management officials as well as the staff personal. (authors)

  6. Programmable controllers replace relays in MFTF-B personnel-safety interlocks

    International Nuclear Information System (INIS)

    Branum, J.D.

    1981-01-01

    This paper describes a new approach for implementing personnel safety interlocks logic using industrial-type programmable controllers. The logic for all personnel safety interlocks except those totally internal to a subsystem is implemented in two non-redundant controllers. A high degree of fail-safe reliability is achieved by augmenting the protective features intrinsic to each controller with those provided by a small amount of external support hardware. The controllers are interfaced to the host computer system via fiber optic data links to enable display of interlock and overall system status on the control room graphic displays. When fully implemented, the controllers will perform the equivalent of over 2000 discreet relay functions

  7. 2. Product quality control and assurance system

    International Nuclear Information System (INIS)

    1990-01-01

    Product quality control and assurance are dealt with in relation to reliability in nuclear power engineering. The topics treated include product quality control in nuclear power engineering, product quality assurance of nuclear power plant equipment, quality assurance programs, classification of selected nuclear power equipment, and standards relating to quality control and assurance and to nuclear power engineering. Particular attention is paid to Czechoslovak and CMEA standards. (P.A.). 2 figs., 1 tab., 12 refs

  8. A survey of approaches combining safety and security for industrial control systems

    International Nuclear Information System (INIS)

    Kriaa, Siwar; Pietre-Cambacedes, Ludovic; Bouissou, Marc; Halgand, Yoran

    2015-01-01

    The migration towards digital control systems creates new security threats that can endanger the safety of industrial infrastructures. Addressing the convergence of safety and security concerns in this context, we provide a comprehensive survey of existing approaches to industrial facility design and risk assessment that consider both safety and security. We also provide a comparative analysis of the different approaches identified in the literature. - Highlights: • We raise awareness of safety and security convergence in numerical control systems. • We highlight safety and security interdependencies for modern industrial systems. • We give a survey of approaches combining safety and security engineering. • We discuss the potential of the approaches to model safety and security interactions

  9. Patients' perceptions of safety and quality of maternity clinical handover

    Directory of Open Access Journals (Sweden)

    Chin Georgiana SM

    2011-08-01

    Full Text Available Abstract Background Maternity clinical handover serves to address the gaps in knowledge existing when transitions between individuals or groups of clinicians occur throughout the antenatal, intra-partum and postnatal period. There are limited published studies on maternity handover and a paucity of information about patients' perceptions of the same. This paper reports postnatal patients' perceptions of how maternity handover contributes to the quality and safety of maternity care. Methods This paper reports on a mixed-methods study consisting of qualitative interviews and quantitative medical record analysis. Thirty English-speaking postnatal patients who gave birth at an Australian tertiary maternity hospital participated in a semi-structured interview prior to discharge from hospital. Interview data were coded thematically using the constant comparative method and managed via NVivo software; this data set was supplemented by medical record data analysed using STATA. Results Almost half of the women were aware of a handover process. Clinician awareness of patient information was seen as evidence that handover had taken place and was seen as representing positive aspects of teamwork, care and communication by participants, all important factors in the perception of quality health care. Collaborative cross-checking, including the use of cognitive artefacts such as hand held antenatal records and patient-authored birth plans, and the involvement of patients and their support people in handover were behaviours described by participants to be protective mechanisms that enhanced quality and safety of care. These human factors also facilitated team situational awareness (TSA, shared decision making and patient motivation in labour. Conclusions This study illustrates that many patients are aware of handover processes. For some patients, evidence of handover, through clinician awareness of information, represented positive aspects of teamwork, care and

  10. Determination and evaluation of air quality control. Manual of ambient air quality control in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Lahmann, E.

    1997-07-01

    Measurement of air pollution emissions and ambient air quality are essential instruments for air quality control. By undertaking such measurements, pollutants are registered both at their place of origin and at the place where they may have an effect on people or the environment. Both types of measurement complement each other and are essential for the implementation of air quality legislation, particularly, in compliance with emission and ambient air quality limit values. Presented here are similar accounts of measurement principles and also contains as an Appendix a list of suitability-tested measuring devices which is based on information provided by the manufacturers. In addition, the guide of ambient air quality control contains further information on discontinuous measurement methods, on measurement planning and on the assessment of ambient air quality data. (orig./SR)

  11. Identification of Patient Safety Risks Associated with Electronic Health Records: A Software Quality Perspective.

    Science.gov (United States)

    Virginio, Luiz A; Ricarte, Ivan Luiz Marques

    2015-01-01

    Although Electronic Health Records (EHR) can offer benefits to the health care process, there is a growing body of evidence that these systems can also incur risks to patient safety when developed or used improperly. This work is a literature review to identify these risks from a software quality perspective. Therefore, the risks were classified based on the ISO/IEC 25010 software quality model. The risks identified were related mainly to the characteristics of "functional suitability" (i.e., software bugs) and "usability" (i.e., interface prone to user error). This work elucidates the fact that EHR quality problems can adversely affect patient safety, resulting in errors such as incorrect patient identification, incorrect calculation of medication dosages, and lack of access to patient data. Therefore, the risks presented here provide the basis for developers and EHR regulating bodies to pay attention to the quality aspects of these systems that can result in patient harm.

  12. 30 CFR 74.6 - Quality control.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality control. 74.6 Section 74.6 Mineral... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and... DUST SAMPLING DEVICES Approval Requirements for Coal Mine Dust Personal Sampler Unit § 74.6 Quality...

  13. The role of hospital managers in quality and patient safety: a systematic review.

    Science.gov (United States)

    Parand, Anam; Dopson, Sue; Renz, Anna; Vincent, Charles

    2014-09-05

    To review the empirical literature to identify the activities, time spent and engagement of hospital managers in quality of care. A systematic review of the literature. A search was carried out on the databases MEDLINE, PSYCHINFO, EMBASE, HMIC. The search strategy covered three facets: management, quality of care and the hospital setting comprising medical subject headings and key terms. Reviewers screened 15,447 titles/abstracts and 423 full texts were checked against inclusion criteria. Data extraction and quality assessment were performed on 19 included articles. The majority of studies were set in the USA and investigated Board/senior level management. The most common research designs were interviews and surveys on the perceptions of managerial quality and safety practices. Managerial activities comprised strategy, culture and data-centred activities, such as driving improvement culture and promotion of quality, strategy/goal setting and providing feedback. Significant positive associations with quality included compensation attached to quality, using quality improvement measures and having a Board quality committee. However, there is an inconsistency and inadequate employment of these conditions and actions across the sample hospitals. There is some evidence that managers' time spent and work can influence quality and safety clinical outcomes, processes and performance. However, there is a dearth of empirical studies, further weakened by a lack of objective outcome measures and little examination of actual actions undertaken. We present a model to summarise the conditions and activities that affect quality performance. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  14. Preliminary measurements of the establishment of a quality control programme for the activimeter calibration reference system

    International Nuclear Information System (INIS)

    Martins, Elaine W.; Potiens, Maria da Penha A.

    2009-01-01

    The nuclear medicine techniques efficiency and safety depends on, beside other factors, a quality control programme, mainly regards to the nuclides activimeter utilization. The Calibration Laboratory of IPEN uses as a work standard, a tertiary standard system Capintec, calibrated at the Accredited Dosimetry Calibration Laboratory of the Medical radiation Research Center - University of Wisconsin. In this work, as preliminary measurements to establish a quality control programme for the activimeter calibration procedures, initially the repeatability and reproducibility (long term stability) tests were performed using a sealed check source of 133 Ba. Later on, to complete this quality control programme other check sources ( 137 Cs, 57 Co, 60 Co) will be used to perform the same tests. A series of 80 experiments of 10 measurements each has been carried out. The reference system showed a good behaviour to the repeatability test, considering the tolerance limits of 5%. The percent deviations of all tested sources in the activity measurements were lower 1% to 133 Ba. (author)

  15. Application of quality assurance controls to TBM tunneling on the Yucca Mountain Project

    International Nuclear Information System (INIS)

    Christensen, J.D.

    1996-01-01

    As part of the Yucca Mountain Project (YMP), a 7.62-meter diameter tunnel is being constructed using a Tunnel Boring Machine (TBM). This tunnel, which may form a portion of a permanent high-level nuclear waste repository, is being constructed under the auspices of a nuclear quality assurance (QA) program. The YMP nuclear QA program applies to items and activities determined to be important to radiological safety, waste isolation, and potential interactions with the environment. The items and activities determined to be important have been assigned a quality assurance classification. This paper focuses on the items (rockbolts, steel sets, and shotcrete) and quality affecting activities involved in providing ground support and excavating the tunnel. Typical activities that have been assigned QA classifications include TBM maintenance, control of water used in the tunnel during construction, and control of diesel emissions in the tunnel. The paper concludes that the key to the successful implementation of nuclear QA requirements for tunneling at Yucca Mountain was the assignment of personnel with the appropriate mix of tunneling and nuclear experience

  16. Comparative analysis of quality assurance systems which effectively control, review and verify the quality of components manufactured for liquid metal cooled fast breeder reactors within the EEC

    International Nuclear Information System (INIS)

    Benn, L.A.

    1985-01-01

    Comparative analyses are made of Quality Assurance Systems, by techniques and the methodology used, for the manufacture of component parts for the Liquid Metal Cooled Fast Breeder Reactor (LMFBR) within the EEC. Two differing alternative systems are presented in the analysis. First, a tabulated analytical treatment which analyses 14 codes and standards relating to Quality Assurance which can be applied to LMFBR's. The comparison equates equivalent clauses between codes and standards followed by an analysis of individual clauses in tabular form, the International Standard ISO 6215. A statistical summary and recommendations conclude this analysis. The second alternative system used in the comparison is a descriptive analytical method applied to 9 selected codes and standards relating to Quality Assurance based on the 13 criteria of the International IAEA Code of Practice no. 50 C.QA entitled ''Quality Assurance for Safety in Nuclear Power Plants''. An investigation is then made of the state of the art on the subject of classification of component parts bearing generally on Quality Assurance. The method of classification is segregated into General, Safety and Inspection categories. A summary of destructive and non destructive controls that may be applied during the manufacture of LMFBR components is given, together with tests that may be applied to selected components, namely Primary Tank, Secondary Sodium Pump and the Primary Cold Trap allocated to Safety Classes, 1, 2 and 3 respectively. The report concludes with a summary of typical records produced at the delivery of a component

  17. Quality factors in the life cycle of software oriented to safety systems in nuclear power plants

    International Nuclear Information System (INIS)

    Nunez McLeod, J.E.; Rivera, S.S.

    1997-01-01

    The inclusion of software in safety related systems for nuclear power plants, makes it necessary to include the software quality assurance concept. The software quality can be defined as the adjustment degree between the software and the specified requirements and user expectations. To guarantee a certain software quality level it is necessary to make a systematic and planned set of tasks, that constitute a software quality guaranty plan. The application of such a plan involves activities that should be performed all along the software life cycle, and that can be evaluated through the so called quality factors, due to the fact that the quality itself cannot be directly measured, but indirectly as some of it manifestations. In this work, a software life cycle model is proposed, for nuclear power plant safety related systems. A set os software quality factors is also proposed , with its corresponding classification according to the proposed model. (author) [es

  18. Application of miniaturized near-infrared spectroscopy for quality control of extemporaneous orodispersible films.

    Science.gov (United States)

    Foo, Wen Chin; Widjaja, Effendi; Khong, Yuet Mei; Gokhale, Rajeev; Chan, Sui Yung

    2018-02-20

    Extemporaneous oral preparations are routinely compounded in the pharmacy due to a lack of suitable formulations for special populations. Such small-scale pharmacy preparations also present an avenue for individualized pharmacotherapy. Orodispersible films (ODF) have increasingly been evaluated as a suitable dosage form for extemporaneous oral preparations. Nevertheless, as with all other extemporaneous preparations, safety and quality remain a concern. Although the United States Pharmacopeia (USP) recommends analytical testing of compounded preparations for quality assurance, pharmaceutical assays are typically not routinely performed for such non-sterile pharmacy preparations, due to the complexity and high cost of conventional assay methods such as high performance liquid chromatography (HPLC). Spectroscopic methods including Raman, infrared and near-infrared spectroscopy have been successfully applied as quality control tools in the industry. The state-of-art benchtop spectrometers used in those studies have the advantage of superior resolution and performance, but are not suitable for use in a small-scale pharmacy setting. In this study, we investigated the application of a miniaturized near infrared (NIR) spectrometer as a quality control tool for identification and quantification of drug content in extemporaneous ODFs. Miniaturized near infrared (NIR) spectroscopy is suitable for small-scale pharmacy applications in view of its small size, portability, simple user interface, rapid measurement and real-time prediction results. Nevertheless, the challenge with miniaturized NIR spectroscopy is its lower resolution compared to state-of-art benchtop equipment. We have successfully developed NIR spectroscopy calibration models for identification of ODFs containing five different drugs, and quantification of drug content in ODFs containing 2-10mg ondansetron (OND). The qualitative model for drug identification produced 100% prediction accuracy. The quantitative

  19. Analysis Method of Common Cause Failure on Non-safety Digital Control System

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yun Goo; Oh, Eun Gse [KHNP, Daejeon (Korea, Republic of)

    2014-08-15

    The effects of common cause failure on safety digital instrumentation and control system had been considered in defense in depth analysis with safety analysis method. However, the effects of common cause failure on non-safety digital instrumentation and control system also should be evaluated. The common cause failure can be included in credible failure on the non-safety system. In the I and C architecture of nuclear power plant, many design feature has been applied for the functional integrity of control system. One of that is segmentation. Segmentation defenses the propagation of faults in the I and C architecture. Some of effects from common cause failure also can be limited by segmentation. Therefore, in this paper there are two type of failure mode, one is failures in one control group which is segmented, and the other is failures in multiple control group because that the segmentation cannot defense all effects from common cause failure. For each type, the worst failure scenario is needed to be determined, so the analysis method has been proposed in this paper. The evaluation can be qualitative when there is sufficient justification that the effects are bounded in previous safety analysis. When it is not bounded in previous safety analysis, additional analysis should be done with conservative assumptions method of previous safety analysis or best estimation method with realistic assumptions.

  20. Distributed sensor architecture for intelligent control that supports quality of control and quality of service.

    Science.gov (United States)

    Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

    2015-02-25

    This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems.

  1. Distributed Sensor Architecture for Intelligent Control that Supports Quality of Control and Quality of Service

    Directory of Open Access Journals (Sweden)

    Jose-Luis Poza-Lujan

    2015-02-01

    Full Text Available This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS parameters and the optimization of control using Quality of Control (QoC parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS communication standard as proposed by the Object Management Group (OMG. As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems.

  2. Quality control education in the community college

    Science.gov (United States)

    Greene, J. Griffen; Wilson, Steve

    1966-01-01

    This paper describes the Quality Control Program at Daytona Beach Junior College, including course descriptions. The program in quality control required communication between the college and the American Society for Quality Control (ASQC). The college has machinery established for certification of the learning process, and the society has the source of teachers who are competent in the technical field and who are the employers of the educational products. The associate degree for quality control does not have a fixed program, which can serve all needs, any more than all engineering degrees have identical programs. The main ideas which would be common to all quality control programs are the concept of economic control of a repetitive process and the concept of developing individual potentialities into individuals who are needed and productive.

  3. TRAINING SYSTEM OF FUTURE SPECIALISTS: QUALITY CONTROL

    Directory of Open Access Journals (Sweden)

    Vladimir A. Romanov

    2015-01-01

    Full Text Available The aim of the investigation is development of innovative strategy of quality control training of engineers and skilled workers (hereinafter – future specialists in educational professional organizations on the principles of social partnership.Methods. Theoretic: theoretic and methodological analysis, polytheoretic synthesis, modeling. Empirical: research and generalization of the system, process and competence – based approaches experience, experiment, observation, surveys, expert evaluation, SWOT-analysis as a method of strategic planning which is to identify the internal and external factors (socio-cultural of the organization surrounding.Results. The strategy of the development of the process of quality control training in educational professional organizations and a predictive model of the system of quality control training for future engineers and workers have been created on the analysis and synthesis of a quantitative specification of the quality, the obtained experience and success in control training of future specialists in educational professional organizations in recent economic and educational conditions.Scientific novelty. There has been built a predicative model of quality control training of future specialists to meet modern standards and the principles of social partnership; the control algorithm of the learning process, developed in accordance with the standards (international of quality ISO in the implementation of the quality control systems of the process approach (matrix-based responsibility, competence and remit of those responsible for the education process in the educational organization, the «problem» terms and diagnostic tools for assessing the quality of professional training of future specialists. The perspective directions of innovation in the control of the quality of future professionals training have been determined; the parameters of a comprehensive analysis of the state of the system to ensure the

  4. Stabilization with guaranteed safety using Control Lyapunov–Barrier Function

    NARCIS (Netherlands)

    Romdlony, Muhammad Zakiyullah; Jayawardhana, Bayu

    2016-01-01

    We propose a novel nonlinear control method for solving the problem of stabilization with guaranteed safety for nonlinear systems. The design is based on the merging of the well-known Control Lyapunov Function (CLF) and the recent concept of Control Barrier Function (CBF). The proposed control

  5. SU-F-P-08: Medical Physics Perspective On Radiation Therapy Quality and Safety Considerations in Low Income Settings

    Energy Technology Data Exchange (ETDEWEB)

    Van Dyk, J [Western University London, ON (Canada); Meghzifene, A [International Atomic Energy Agency, Vienna (Austria)

    2016-06-15

    Purpose: The last few years have seen a significant growth of interest in the global radiation therapy crisis. Various organizations are quantifying the need and providing aid in support of addressing the shortfall existing in many low-to-middle income countries (LMICs). The Lancet Oncology Commission report (Lancet Oncol. Sep;16(10):1153-86, 2015) projects a need of 22,000 new medical physicists in LMICs by 2035 if there is to be equal access globally. With the tremendous demand for new facilities, equipment and personnel, it is very important to recognize quality and safety considerations and to address them directly. Methods: A detailed examination of quality and safety publications was undertaken. A paper by Dunscombe (Front. Oncol. 2: 129, 2012) reviewed the recommendations of 7 authoritative reports on safety in radiation therapy and found the 12 most cited recommendations, summarized in order of most to least cited: training, staffing, documentation/standard operating procedures, incident learning, communication/questioning, check lists, QC/PM, dosimetric audit, accreditation, minimizing interruptions, prospective risk assessment, and safety culture. However, these authoritative reports were generally based on input from high income contexts. In this work, the recommendations were analyzed with a special emphasis on issues that are significant in LMICs. Results: The review indicated that there are significant challenges in LMICs with training and staffing ranking at the top in terms quality and safety. Conclusion: With the recognized need for expanding global access to radiation therapy, especially in LMICs, and the backing by multiple support organizations, quality and safety considerations must be overtly addressed. While multidimensional, training and staffing are top priorities. The use of outdated systems with poor interconnectivity, coupled with a lack of systematic QA in high patient load settings are additional concerns. Any support provided to lower

  6. SU-F-P-08: Medical Physics Perspective On Radiation Therapy Quality and Safety Considerations in Low Income Settings

    International Nuclear Information System (INIS)

    Van Dyk, J; Meghzifene, A

    2016-01-01

    Purpose: The last few years have seen a significant growth of interest in the global radiation therapy crisis. Various organizations are quantifying the need and providing aid in support of addressing the shortfall existing in many low-to-middle income countries (LMICs). The Lancet Oncology Commission report (Lancet Oncol. Sep;16(10):1153-86, 2015) projects a need of 22,000 new medical physicists in LMICs by 2035 if there is to be equal access globally. With the tremendous demand for new facilities, equipment and personnel, it is very important to recognize quality and safety considerations and to address them directly. Methods: A detailed examination of quality and safety publications was undertaken. A paper by Dunscombe (Front. Oncol. 2: 129, 2012) reviewed the recommendations of 7 authoritative reports on safety in radiation therapy and found the 12 most cited recommendations, summarized in order of most to least cited: training, staffing, documentation/standard operating procedures, incident learning, communication/questioning, check lists, QC/PM, dosimetric audit, accreditation, minimizing interruptions, prospective risk assessment, and safety culture. However, these authoritative reports were generally based on input from high income contexts. In this work, the recommendations were analyzed with a special emphasis on issues that are significant in LMICs. Results: The review indicated that there are significant challenges in LMICs with training and staffing ranking at the top in terms quality and safety. Conclusion: With the recognized need for expanding global access to radiation therapy, especially in LMICs, and the backing by multiple support organizations, quality and safety considerations must be overtly addressed. While multidimensional, training and staffing are top priorities. The use of outdated systems with poor interconnectivity, coupled with a lack of systematic QA in high patient load settings are additional concerns. Any support provided to lower

  7. Current quality criteria

    International Nuclear Information System (INIS)

    Sajaroff, Pedro M.

    1999-01-01

    The Safety Series 50-C/SG-Q 'Quality Assurance for Safety in Nuclear Power Plants and other Nuclear Installations' published by the IAEA in 1996, contains the Code and 14 Safety Guides. It is more addressed to operating organizations than to regulatory authorities. Priority is assigned to programme implementation and to work effectiveness. Emphasis is putted on doing work correctly from the very beginning (right first time attitude), and not on finding and correcting errors instead of preventing them. The essential aspects for assuring quality (that is, for achieving and maintaining an acceptable level of safety) cover the ten basic requirements established by the Code: Management (QA programme, training and qualification, non-conformance control and corrective actions, document control and records); Performance (work, design, procurement, inspection and testing for acceptance); and Assessment (management self-assessment, independent assessment). These requirements are applicable, on a graded approach basis, to the overall QA programme of the operating organization and its partial programmes during design, construction, commissioning, operation and decommissioning stages. The requirements can be also applied, with due adaptations, to other nuclear installations. The research and development activities related to such stages are comprised under the quality 'umbrella' as well. Therefore the scope of the traditional quality assurance is expanded and consolidated as a management tool more oriented to user. Responsibilities for achieving quality objectives are assigned to all involved individuals and organizations at all levels: management, working groups and assessment teams. Managers' is important but individual responsibilities are unavoidable. For the Argentine Nuclear Regulatory Authority, performance-based quality assurance was not a novelty. In line with the regulatory philosophy (which is essentially based on performance) the regulatory standard AR 3.6.1 (Rev.1

  8. Physical aspects of quality assurance in nuclear medicine and radiotherapy, regulatory approach of the National Nuclear Safety Center; Aspectos fisicos de garantia de calidad en medicina nuclear y radioterapia. Enfoque regulatorio del centro Nacional de Seguridad Nuclear

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez C, D.; Fuente P, A. de la; Quevedo G, J.R.; Lopez F, Y. [CNSN, Calle 28 No. 504 e/5 y 7, Ave. Miramar, La Habana (Cuba); Varela C, C. [CCEEM, Calle 4 No. 455 e/19 y 21, Ave. Vedado, La Habana (Cuba)]. e-mail: cruz@orasen.co.cu

    2006-07-01

    The physical aspects of the quality guarantee in Nuclear Medicine and Radiotherapy its are of cardinal importance to guarantee the quality of the diagnoses and treatments that are carried out to the patients in this type of services. The OIEA, the OMS and other scientific and professional organizations have contributed significantly to the elaboration of recommendations, Protocols, etc. applicable in the quality control programs and safety of the Nuclear Medicine and Radiotherapy departments. In spite of the great effort developed in this sense the Installation of the programs of quality control and safety of the Nuclear Medicine and Radiotherapy departments can fail if the same ones are not based in three decisive elements that are: the existence of national regulations, the existence of the infrastructure required for it and the existence of enough qualified personnel to develop this programs. The present work shows the regulatory focus that on this topic, it has followed the National Center of Nuclear Safety of Cuba (CNSN). The same left of strengthen all the existent Synergies in the different organizations of the country and it went in two fundamental directions: installation of the regulatory requirements that govern this activity and the Authorization of a Cuban Entity, specialized in carrying out audits to the quality control and safety programs of the Nuclear Medicine and Radiotherapy departments. After 4 work years in this direction, the results confirm the validity of the experience developed by the CNSN, at the moment all the services of Nuclear Medicine and Radiotherapy of Cuba possess quality control and safety programs, these programs are annually Auditing by an Authorized entity by the CNSN and the Inspectors of the Regulatory Authority, control, during the inspections, the one execution of the established requirements in the national regulations. The work developed so far can serve, modestly, of reference to others countries of Latin America that

  9. Pharmaceutical quality of "party pills" raises additional safety concerns in the use of illicit recreational drugs.

    Science.gov (United States)

    Young, Simon A; Thrimawithana, Thilini R; Antia, Ushtana; Fredatovich, John D; Na, Yonky; Neale, Peter T; Roberts, Amy F; Zhou, Huanyi; Russell, Bruce

    2013-06-14

    To determine the content and release kinetics of 1-benzylpiperazine (BZP) and 1-(3-trifluoromethyl-phenyl)piperazine (TFMPP) from "party pill" formulations. From these data, the possible impact of pharmaceutical quality upon the safety of such illicit formulations may be inferred. The amount of BZP and TFMPP in party pill formulations was determined using a validated HPLC method. The in-vitro release kinetics of selected party pill brands were determined using a USP dissolution apparatus (75 rpm, 37.5 degrees Celsius). The release data were then fitted to a first order release model using PLOT software and the time taken to achieve 90% release reported. Many of the tested party pill brands contained amounts of BZP and TFMPP that varied considerably from that stated on the packaging; including considerable TFMPP content in some brands not labelled to contain this drug. Dissolution studies revealed that there was considerable variability in the release kinetics between brands; in one case 90% release required >30 minutes. Lack of quality control in party pill manufacture may have led to the toxic effects reported by users unaware of the true content and release of drug from pills. More stringent regulation in the manufacture and quality control of "new generation party pills" is essential to the harm reduction campaign.

  10. Data Analysis of Occupational Health and Safety Management and Total Quality Management Systems

    Directory of Open Access Journals (Sweden)

    Ahmet Yakut

    2013-01-01

    Full Text Available In our study, Total Quality Management, Occupational Health and Safety on the effects of the construction industry, building sites of Istanbul evaluated with the results of the survey of 25 firms. For Occupational Health and Safety program, walked healthy, active employees in her role increased and will increase the importance of education. Due to non-implementation of the OHS system in our country enough, work-related accidents and deaths and injuries resulting from these accidents is very high. Firms as a result of the analysis, an effective health and safety management system needs to be able to fulfill their responsibilities. This system is designated as OHSAS 18001 Occupational Health and Safety Management System and the construction industry can be regarded as the imperatives.

  11. Safety of nuclear operation and maintenance

    International Nuclear Information System (INIS)

    Mori, M.; Nitta, T.; Sakai, K.

    1994-01-01

    The Kansai Electric Power Co. Inc.(Kansai EPC) aims to pursue a high quality and highly reliable operation in nuclear power generation in order to ensure safety by reducing the risk of accidents and win the confidence from the society and the public. It is emphasised that in order to realize this aim manufacturers and contractors cooperate with each other in performing high quality maintenance through plant lifetime maintenance system. TQC (Total Quality Control) activity enhances the motivation for each individual to have a quality-oriented mind and cultivate the safety culture. Under the lifetime employment practice, Kansai EPC and maintenance contractors can conduct systematic education and training, and the Maintenance Training Center helps to make it effective. 6 figs

  12. 14 CFR 145.211 - Quality control system.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Quality control system. 145.211 Section 145...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable to...

  13. 18 CFR 12.40 - Quality control programs.

    Science.gov (United States)

    2010-04-01

    ... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Quality control... PROJECT WORKS Other Responsibilities of Applicant or Licensee § 12.40 Quality control programs. (a... meeting any requirements or standards set by the Regional Engineer. If a quality control program is...

  14. Developing methods of controlling quality costs

    Directory of Open Access Journals (Sweden)

    Gorbunova A. V.

    2017-01-01

    Full Text Available The article examines issues of managing quality costs, problems of applying economic methods of quality control, implementation of progressive methods of quality costs management in enterprises with the view of improving the efficiency of their evaluation and analysis. With the aim of increasing the effectiveness of the cost management mechanism, authors introduce controlling as a tool of deviation analysis from the standpoint of the process approach. A list of processes and corresponding evaluation criteria in the quality management system of enterprises is introduced. Authors also introduce the method of controlling quality costs and propose it for the practical application, which allows them to determine useful and unnecessary costs at the existing operating plant. Implementing the proposed recommendations in the system of cost management at an enterprise will allow to improve productivity of processes operating and reduce wasted expense on the quality of the process on the basis of determining values of useful and useless costs of quality according to criteria of processes functioning in the system of quality management.

  15. Microbiological Quality and Safety of Fresh Fruits and Vegetables at Retail Levels in Korea.

    Science.gov (United States)

    Tango, Charles Nkufi; Wei, Shuai; Khan, Imran; Hussain, Mohammad Shakhawat; Kounkeu, Paul-François Ngnitcho; Park, Joong-Hyun; Kim, Se-Hun; Oh, Deog Hwan

    2018-02-01

    The aim of this study was to evaluate the microbiological quality and safety of fresh produce at retail level in Korea in order to periodically update information and establish available risks associated with consumption of fresh fruits and vegetables. The samples from different markets located in 3 provinces of South Korea were collected. The protocol in the Korean Food Standards Codex was applied and generic Escherichia coli, coliforms, aerobic mesophilic bacteria (AMB), and yeast and mold (YM) in 360 packaged and unpackaged fresh fruits and vegetables were analyzed. Presence of pathogens was examined using real-time polymerase chain reaction (q-PCR) after enrichment of samples. For all, the microbial counts ranged from 1.7 to 10.6 log cfu/g for AMB, 2.2 to 7.9 log cfu/g for coliforms, and 5.5 to 7.9 log cfu/g for YM. Three lettuce samples were contaminated by E. coli with a bacterial load ranging from 2 to 4 log cfu/g. Salmonella spp. were not detected in any fresh produce. Listeria monocytogenes, E. coli O157:H7, and Staphylococcus aureus were found in 1 (0.6%), 3 (0.8%), and 5 (1.4%) fresh produce samples, respectively. Bacillus cereus (50.3%) and Clostridium perfringens (13.3%) had the highest prevalence. These results indicate the need for employing strict control measures and developing preventive strategies to improve the quality and safety of fresh produce in Korea. © 2018 Institute of Food Technologists®.

  16. Improving Hospital Quality and Patient Safety an Examination of Organizational Culture and Information Systems

    Science.gov (United States)

    Gardner, John Wallace

    2012-01-01

    This dissertation examines the effects of safety culture, including operational climate and practices, as well as the adoption and use of information systems for delivering high quality healthcare and improved patient experience. Chapter 2 studies the influence of both general and outcome-specific hospital climate and quality practices on process…

  17. Trends in Control Area of PLC Reliability and Safety Parameters

    Directory of Open Access Journals (Sweden)

    Juraj Zdansky

    2008-01-01

    Full Text Available Extension of the PLC application possibilities is closely related to increase of reliability and safety parameters. If the requirement of reliability and safety parameters will be suitable, the PLC could by implemented to specific applications such the safety-related processes control. The goal of this article is to show the way which producers are approaching to increase PLC`s reliability and safety parameters. The second goal is to analyze these parameters for range of present choice and describe the possibility how the reliability and safety parameters can be affected.

  18. Some questions of monitoring on nuclear installations and quality of safety assessments

    International Nuclear Information System (INIS)

    Labazov, V.

    1998-01-01

    The paper is prepared on the basis of assessment performed by the State Scientific and Technical Centre on Nuclear and Radiation safety which deals with scientific and technical support of the Regulatory Authorities of Ukraine concerning integrity of pressurised elements in the NPP. A number of acute issues on control equipment could be distinguished: placement of sensors should provide adequate information on the data under control necessary for safety analysis; properties of instrumentation should provide trustworthy information about measured values; accurate recommendations should be imposed to operating organisations for performing special analyses for control devices

  19. Computer controlled quality of analytical measurements

    International Nuclear Information System (INIS)

    Clark, J.P.; Huff, G.A.

    1979-01-01

    A PDP 11/35 computer system is used in evaluating analytical chemistry measurements quality control data at the Barnwell Nuclear Fuel Plant. This computerized measurement quality control system has several features which are not available in manual systems, such as real-time measurement control, computer calculated bias corrections and standard deviation estimates, surveillance applications, evaluaton of measurement system variables, records storage, immediate analyst recertificaton, and the elimination of routine analysis of known bench standards. The effectiveness of the Barnwell computer system has been demonstrated in gathering and assimilating the measurements of over 1100 quality control samples obtained during a recent plant demonstration run. These data were used to determine equaitons for predicting measurement reliability estimates (bias and precision); to evaluate the measurement system; and to provide direction for modification of chemistry methods. The analytical chemistry measurement quality control activities represented 10% of the total analytical chemistry effort

  20. Control of the Saclay CEA's base nuclear installations - Inspection n. INS-2010-CEASAC-0006 31 May 2010-4 June 2010 - Safety management

    International Nuclear Information System (INIS)

    2010-01-01

    This document reports an inspection dedicated to safety management, and performed by the ASN (the French Nuclear Safety Authority) on several nuclear installations present on the CEA's Saclay site. The inspected installations have been the INBs (base nuclear installations) number 35 (STEL), 40 (Osiris), 49 (LHA), 50 (LECI), 77 (Poseidon) and 101 (Orphee), and four departments (CCSIMN, USL2TI, SP2S and DANS) involved in safety or in charge of it. The report describes the requested corrective actions about the quality of the internal diagnosis, about the follow-up of actions and directives, about internal authorizations, about the follow-up of commitments, about second level control, about the management of the return on experience, about interesting events, about the control of subcontractors. Some additional information requests are also formulated

  1. Who is in control of road safety? A STAMP control structure analysis of the road transport system in Queensland, Australia.

    Science.gov (United States)

    Salmon, Paul M; Read, Gemma J M; Stevens, Nicholas J

    2016-11-01

    Despite significant progress, road trauma continues to represent a global safety issue. In Queensland (Qld), Australia, there is currently a focus on preventing the 'fatal five' behaviours underpinning road trauma (drug and drink driving, distraction, seat belt wearing, speeding, and fatigue), along with an emphasis on a shared responsibility for road safety that spans road users, vehicle manufacturers, designers, policy makers etc. The aim of this article is to clarify who shares the responsibility for road safety in Qld and to determine what control measures are enacted to prevent the fatal five behaviours. This is achieved through the presentation of a control structure model that depicts the actors and organisations within the Qld road transport system along with the control and feedback relationships that exist between them. Validated through a Delphi study, the model shows a diverse set of actors and organisations who share the responsibility for road safety that goes beyond those discussed in road safety policies and strategies. The analysis also shows that, compared to other safety critical domains, there are less formal control structures in road transport and that opportunities exist to add new controls and strengthen existing ones. Relationships that influence rather than control are also prominent. Finally, when compared to other safety critical domains, the strength of road safety controls is brought into question. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Development and perceived effects of an educational programme on quality and safety in medication handling in residential facilities.

    Science.gov (United States)

    Mygind, Anna; El-Souri, Mira; Rossing, Charlotte; Thomsen, Linda Aagaard

    2018-04-01

    To develop and test an educational programme on quality and safety in medication handling for staff in residential facilities for the disabled. The continuing pharmacy education instructional design model was used to develop the programme with 22 learning objectives on disease and medicines, quality and safety, communication and coordination. The programme was a flexible, modular seven + two days' course addressing quality and safety in medication handling, disease and medicines, and medication supervision and reconciliation. The programme was tested in five Danish municipalities. Municipalities were selected based on their application for participation; each independently selected a facility for residents with mental and intellectual disabilities, and a facility for residents with severe mental illnesses. Perceived effects were measured based on a questionnaire completed by participants before and after the programme. Effects on motivation and confidence as well as perceived effects on knowledge, skills and competences related to medication handling, patient empowerment, communication, role clarification and safety culture were analysed conducting bivariate, stratified analyses and test for independence. Of the 114 participants completing the programme, 75 participants returned both questionnaires (response rate = 66%). Motivation and confidence regarding quality and safety in medication handling significantly improved, as did perceived knowledge, skills and competences on 20 learning objectives on role clarification, safety culture, medication handling, patient empowerment and communication. The programme improved staffs' motivation and confidence and their perceived ability to handle residents' medication safely through improved role clarification, safety culture, medication handling and patient empowerment and communication skills. © 2017 Royal Pharmaceutical Society.

  3. A systematic review of human factors and ergonomics (HFE)-based healthcare system redesign for quality of care and patient safety.

    Science.gov (United States)

    Xie, Anping; Carayon, Pascale

    2015-01-01

    Healthcare systems need to be redesigned to provide care that is safe, effective and efficient, and meets the multiple needs of patients. This systematic review examines how human factors and ergonomics (HFE) is applied to redesign healthcare work systems and processes and improve quality and safety of care. We identified 12 projects representing 23 studies and addressing different physical, cognitive and organisational HFE issues in a variety of healthcare systems and care settings. Some evidence exists for the effectiveness of HFE-based healthcare system redesign in improving process and outcome measures of quality and safety of care. We assessed risk of bias in 16 studies reporting the impact of HFE-based healthcare system redesign and found varying quality across studies. Future research should further assess the impact of HFE on quality and safety of care, and clearly define the mechanisms by which HFE-based system redesign can improve quality and safety of care.

  4. Quality assurance, quality control and quality audit in diagnostic radiology

    International Nuclear Information System (INIS)

    Vassileva, J.

    2009-01-01

    Full text:The lecture aims to present contemporary view of quality assurance in X-Ray diagnosis and its practical realization in Bulgaria. In the lecture the concepts of quality assurance, quality control and clinical audit will be defined and their scope will be considered. An answer of the following questions will be given: why is it necessary to determine the dose of patient in X-ray studies, what is the reference dose level and how it is used for dosimetric quantity which characterized the patient's exposure in X-ray, mammography and CT scans and how they are measured, who conducted the measurement and how to keep the records, what are the variations of doses in identical tests and what defines them? The findings from a national survey of doses in diagnostic radiology, conducted in 2008-2009 and the developed new national reference levels will be presented. The main findings of the first tests of radiological equipment and the future role of quality control as well as the concept of conducting clinical audit and its role in quality assurance are also presented. Quality assurance of the diagnostic process with minimal exposure of patients is a strategic goal whose realization requires understanding, organization and practical action, both nationally and in every hospital. To achieve this the important role of education and training of physicians, radiological technicians and medical physicists is enhanced

  5. Safety margins in older adults increase with improved control of a dynamic object

    Science.gov (United States)

    Hasson, Christopher J.; Sternad, Dagmar

    2014-01-01

    Older adults face decreasing motor capabilities due to pervasive neuromuscular degradations. As a consequence, errors in movement control increase. Thus, older individuals should maintain larger safety margins than younger adults. While this has been shown for object manipulation tasks, several reports on whole-body activities, such as posture and locomotion, demonstrate age-related reductions in safety margins. This is despite increased costs for control errors, such as a fall. We posit that this paradox could be explained by the dynamic challenge presented by the body or also an external object, and that age-related reductions in safety margins are in part due to a decreased ability to control dynamics. To test this conjecture we used a virtual ball-in-cup task that had challenging dynamics, yet afforded an explicit rendering of the physics and safety margin. The hypotheses were: (1) When manipulating an object with challenging dynamics, older adults have smaller safety margins than younger adults. (2) Older adults increase their safety margins with practice. Nine young and 10 healthy older adults practiced moving the virtual ball-in-cup to a target location in exactly 2 s. The accuracy and precision of the timing error quantified skill, and the ball energy relative to an escape threshold quantified the safety margin. Compared to the young adults, older adults had increased timing errors, greater variability, and decreased safety margins. With practice, both young and older adults improved their ability to control the object with decreased timing errors and variability, and increased their safety margins. These results suggest that safety margins are related to the ability to control dynamics, and may explain why in tasks with simple dynamics older adults use adequate safety margins, but in more complex tasks, safety margins may be inadequate. Further, the results indicate that task-specific training may improve safety margins in older adults. PMID:25071566

  6. Safety Margins in Older Adults Increase with Improved Control of a Dynamic Object

    Directory of Open Access Journals (Sweden)

    Christopher James Hasson

    2014-07-01

    Full Text Available Older adults face decreasing motor capabilities due to pervasive neuromuscular degradations. As a consequence errors in movement control increase. Thus, older individuals should maintain larger safety margins than younger adults. While this has been shown for object manipulation tasks, several reports on whole-body activities, such as posture and locomotion, however demonstrate age-related reductions in safety margins. This is despite increased costs for control errors, such as a fall. We posit that this paradox could be explained by the dynamic challenge presented by the body or an external object, and that age-related reductions in safety margins are in part due to a decreased ability to control dynamics. To test this conjecture we used a virtual ball-in-cup task that had challenging dynamics, yet afforded an explicit rendering of the physics and safety margin. The hypotheses were: 1 When manipulating an object with challenging dynamics, older adults have smaller safety margins than younger adults. 2 Older adults increase their safety margins with practice. Nine young and 10 healthy older adults practiced moving the virtual ball-in-cup to a target location in exactly two seconds. The accuracy and precision of the timing error quantified skill and the ball energy relative to an escape threshold quantified the safety margin. Compared to the young adults, older adults had increased timing errors, greater variability, and decreased safety margins. With practice, both young and older adults improved their ability to control the object with decreased timing errors and variability, and increased their safety margins. These results suggest that safety margins are related to the ability to control dynamics, and may explain why in tasks with simple dynamics older adults use adequate safety margins, but in more complex tasks, safety margins may be inadequate. Further, the results indicate that task-specific training may improve safety margins in older

  7. Employee quality, monitoring environment and internal control

    Directory of Open Access Journals (Sweden)

    Chunli Liu

    2017-03-01

    Full Text Available We investigate the effect of internal control employees (ICEs on internal control quality. Using special survey data from Chinese listed firms, we find that ICE quality has a significant positive influence on internal control quality. We examine the effect of monitoring on this result and find that the effect is more pronounced for firms with strict monitoring environments, especially when the firms implement the Chinese internal control regulation system (CSOX, have higher institutional ownership or attach greater importance to internal control. Our findings suggest that ICEs play an important role in the design and implementation of internal control systems. Our study should be of interest to both top managers who wish to improve corporate internal control quality and regulators who wish to understand the mechanisms of internal control monitoring.

  8. METHODS OF CONTROL DIPHTHERIA VACCINE SAFETY

    Directory of Open Access Journals (Sweden)

    Isayenko Ye. Yu

    2016-12-01

    Full Text Available Vaccination success depends not only on the timely coverage of threatened contingents, but also on the quality of vaccines. Every day, the requirements for security guarantees vaccines and their use guarantees of security increases. For the fast, reliable and independent scientific assessment of vaccine safety issues, WHO in 1999 created the Global Advisory Committee on Vaccine Safety. To enhance the capacity of pharmaceutical supervision in relation to vaccines in 2012 it was developed the Global Vaccine Safety Initiative. The main directions of the Global Vaccine Safety programs are considered in this review. It’s noted more strict requirements of Ukrainian pharmaceutical industry to produce public immunization drugs regulated Supplements to the State Pharmacopoeia of Ukraine, in comparison with other countries. This review considered diphtheria vaccine safety monitoring in the process of production according to the recommendations of the World Health Organization (WHO, described a subcutaneous method for determining the specific toxicity of the combined purified toxoid, characterized an intracutaneous method of determining of the presence of diphtheria toxin in each sample of the combined purified toxoid, that additionally used by some manufacturers. The definition of diphtheria toxin in dilutions of purified toxoid is presented. This review considered diphtheria vaccine safety monitoring in the process of production according to the recommendations of the World Health Organization (WHO, described a subcutaneous method for determining the specific toxicity of the combined purified toxoid, characterized an intracutaneous method of determining of the presence of diphtheria toxin in each sample of the combined purified toxoid, that additionally used by some manufacturers. The definition of diphtheria toxin in dilutions of purified toxoid is presented. As methods for determination of diphtheria toxin must be able to detect even a small amount

  9. Problems of quality assurance and quality control in diagnostic radiology

    International Nuclear Information System (INIS)

    Angerstein, W.

    1986-01-01

    Topical problems of quality assurance and quality control in diagnostic radiology are discussed and possible solutions are shown. Complex units are differentiated with reference to physicians, technicians, organization of labour, methods of examination and indication. Quality control of radiologic imaging systems should involve three stages: (1) simple tests carried out by radiologic technicians, (2) measurements by service technicians, (3) testing of products by the manufacturer and independent governmental or health service test agencies. (author)

  10. Quality Control in construction.

    Science.gov (United States)

    1984-01-01

    behavioral scientists. In 1962, Dr. Kaoru Ishikawa gave shape to the form of training which featured intradepartmental groups of ten or so workers seated...and Japanese circles bears closer scrutiny. 4.3.1 Japanese Ingredients of Quality The founder of quality circles, Dr. Kaoru Ishikawa , gives six...around 51 a table; hence the name Quality Control Circle. 4 Dr. 0 Ishikawa was an engineering professor at Tokyo University, and the circles were

  11. Safety aspects in radiology

    International Nuclear Information System (INIS)

    Silva, D.C. da.

    1991-05-01

    The development of a program for the evaluation of the physical installations and operational procedures in diagnostic radiology with respect to radiation-safety is described. In addition, a proposal for the quality analysis of X-ray equipment and film-processing is presented. The purpose is both to ensure quality and safety of the radiology service, as well as to aid in the initial and in-service training of the staff. Interviews with patients, staff practicing radiology at a wide range of levels and the controlling authorities were carried out in the State of Rio de Janeiro in order to investigate the existence and the effective use of personal radioprotection equipment as well as user's and staff's concern for radiation safety. Additionally physical measurements were carried out in University Hospitals in Rio de Janeiro to assess the quality of equipment in day-to-day use. It was found that in the locations which did not have routine maintenance the equipment was generally in a poor state which lead to a high incidence of repetition of examinations and the consequent financial loss. (author)

  12. Establishment for quality control of experimental animal

    International Nuclear Information System (INIS)

    Kim, Tae Hwan; Kim, Soo Kwan; Kim, Tae Kyoung

    1999-06-01

    Until now, because we have imported experimental animal from foreign experimental animal corporation, we could have saved money by establishing the quality control of animal in barrier system. In order to improve the quality of animal experiment and efficiency of biomedical study, it is indispensable to control many factors that effect in the experiment. Therefore, it is essential to organize the system of laboratory animal care for enhancing reliability and revivability of experimental results. The purpose of the present investigation was to establish the quality control system of experimental animals that we can provide good quality animals according to the experimental condition of each investigator although the exact quality control system to estimate the infection of bacteria and virus easily remains ill-defined yet. Accordingly, we established the useful quality control system for microbiologic monitoring and environmental monitoring to protect experimental animal from harmful bacteria and virus

  13. Establishment for quality control of experimental animal

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae Hwan; Kim, Soo Kwan; Kim, Tae Kyoung

    1999-06-01

    Until now, because we have imported experimental animal from foreign experimental animal corporation, we could have saved money by establishing the quality control of animal in barrier system. In order to improve the quality of animal experiment and efficiency of biomedical study, it is indispensable to control many factors that effect in the experiment. Therefore, it is essential to organize the system of laboratory animal care for enhancing reliability and revivability of experimental results. The purpose of the present investigation was to establish the quality control system of experimental animals that we can provide good quality animals according to the experimental condition of each investigator although the exact quality control system to estimate the infection of bacteria and virus easily remains ill-defined yet. Accordingly, we established the useful quality control system for microbiologic monitoring and environmental monitoring to protect experimental animal from harmful bacteria and virus.

  14. Modern Aspects of Safety Assessment of Foodstuff

    Directory of Open Access Journals (Sweden)

    Tetiana Chorna

    2018-04-01

    Full Text Available Food safety is one of the decisive components of the economic security of each state and is determined by the ability of the country to control effectively the production and import of safe and high-quality food on the generally accepted principles of the world. This sphere of activity in human society has extremely important humanitarian, social, economic and political aspects. The food raw materials and food products quality and safety control is currently the most relevant analytical task. It is more important than environmental pollution, according to some data, more than 70 % of harmful pollutants in the human body gets through food, 20% of water and 10 % of the air. Technogenic pollution of the environment through soil, water and air gets directly into the food. However, food products are contaminated with natural harmful substances that appear in improper storage, in violation of technologies, food processing and processing charts. The article is devoted to the main factors analysis influencing the safety of food products and the improvement of instrumental methods for the study of quality aromatic products (for example, coffee.

  15. Analyze for the Quality Control of General X-ray Systems in Capital region

    International Nuclear Information System (INIS)

    Kang, Byung Sam; Lee, Kang Min; Shin, Woo Yong; Park, Soon Chul; Choi, Hak Dong; Cho, Yong Kwon

    2012-01-01

    Thanks to the rapid increase of the interest in the quality control of the General X-ray systems, this research proposes the direction of the quality control through comparing and inspecting the actual condition of the respective quality control in the Clinic, the educational institution and the hospital. The subjects of the investigation are diagnostic radiation equipment's in the clinic, the educational institution and the hospital around the capital. A test of kVp, mR/mAs out put test and reproducibility of the exposure dose, half value layer, an accordance between the light field and the beam alignment test, and lastly reproducibility of the exposure time. Then the mean difference of the percentage, the CV (Coefficient of Variation, CV) and the attenuated curve which are respectively resulted from the above tests are computed. After that we have evaluated the values according to the regulations on the Diagnostic Radiation Equipment Safety Administration regulations. In the case of the clinic and the educational institution, there were 22 general X-ray devices. And 18.2% of the kVp test, 13.6% of the reproducibility of exposure dose test, 9.1% of the mR/mAs out put test, and 13.6% of the HVL (Half Value Layer) test appeared to be improper. In the case of the hospital, however, there were 28 devices. And 7.1% of the reproducibility of exposure dose, 7.1% of the difference in the light field/ beam alignment, and 7.1% of the reproducibility of the exposure time appeared to be improper. According to the investigation, the hospital's quality control condition is better than the condition in the clinic and the educational institution. The quality control condition of the general X-ray devices in the clinic is unsatisfactory compared to the hospital. Thus, it is considered that realizing the importance of the quality control is necessary.

  16. Quality control for dose calibrators

    International Nuclear Information System (INIS)

    Mendes, L.C.G.

    1984-01-01

    Nuclear medicine laboratories are required to assay samples of radioactivity to be administered to patients. Almost universally, these assays are accomplished by use of a well ionization chamber isotope calibrator. The Instituto de Radioprotecao e Dosimetria (Institute for Radiological Protection and Dosimetry) of the Comissao Nacional de Energia Nuclear (National Commission for Nuclear Energy) is carrying out a National Quality Control Programme in Nuclear Medicine, supported by the International Atomic Energy Agency. The assessment of the current needs and practices of quality control in the entire country of Brazil includes Dose Calibrators and Scintillation Cameras, but this manual is restricted to the former. Quality Control Procedures for these Instruments are described in this document together with specific recommendations and assessment of its accuracy. (author)

  17. Antisideslip and Antirollover Safety Speed Controller Design for Vehicle on Curved Road

    Directory of Open Access Journals (Sweden)

    Guo Lie

    2014-01-01

    Full Text Available When the drivers cannot be aware of the existing of forthcoming curved roads and fail to regulate their safety speeds accordingly, sideslip or rollover may occur with high probability. The antisideslip and antirollover control of vehicle on curved road in automatic highway systems is studied. The safety speed warning system is set before entering the curved road firstly. The speed adhesion control is adopted to shorten the braking distance while decelerating and to guarantee the safety speed. The velocity controller when decelerating on the straight path and the posture controller when driving on curved road are designed, respectively, utilizing integral backstepping technology. Simulation results demonstrate that this control system is characterized by quick and precise tracking and global stability. Consequently, it is able to avoid the dangerous operating conditions, such as sideslip and rollover, and guarantee the safety and directional stability when driving on curved road.

  18. New Methodology for a Comprehensive Modular Safety Control System in a Cyclotron Site

    International Nuclear Information System (INIS)

    Kaufman, Y.; Kravitz, M.; Arad, M.; Osovizky, A.; Paran, J.; Sarussi, B.; Ellenbogen, M.; Tal, N.

    2004-01-01

    This Paper describes a new methodology for a comprehensive modular Safety Control System (SCS), for a cyclotron site. The developed SCS is a modular approach for controlling the production procedures, safety conditions and documentation aspects in the Cyclotron site. Usually, the safety conditions in cyclotron sites are maintained by a variety of sensors. The cyclotron is supplied from the manufacturer with a self-integrated control system for its operation, yet the comprehensive SCS has to be defined and setup by the customer. Therefore, customers face a lot of integration problems in trying to combine all the signals from the different safety systems such as radiation monitoring, environmental and access control, in order to maintain proper safety working conditions. The presented SCS design provides main user interface and the complete safety solution required by including preset control logic definitions and open logic for specific user applications. The knowledge for the preset control logic definitions was gathered in previous projects. Failure Mode and Effects Analysis (FMEA) method has been implemented on the SCS to analyze the potential failure modes and their impact on the product reliability

  19. Canadian Association of Gastroenterology Consensus Guidelines on Safety and Quality Indicators in Endoscopy

    Directory of Open Access Journals (Sweden)

    David Armstrong

    2012-01-01

    Full Text Available Several organizations worldwide have developed procedure-based guidelines and/or position statements regarding various aspects of quality and safety indicators, and credentialing for endoscopy. Although important, they do not specifically address patient needs or provide a framework for their adoption in the context of endoscopy services. The consensus guidelines reported in this article, however, aimed to identify processes and indicators relevant to the provision of high-quality endoscopy services that will support ongoing quality improvement across many jurisdictions, specifically in the areas of ethics, facility standards and policies, quality assurance, training and education, reporting standards and patient perceptions.

  20. The Designing Bus for Nuclear Safety Class Controller

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dongil; Lee, Myeongkyun; Yun, Donghwa [PONUTech Co,. Ltd., Research Institute, Ulsan (Korea, Republic of); Ryoo, Kwangki [Hanbat National Univ., Daejeon (Korea, Republic of)

    2013-10-15

    EtherCAT (Ethernet for Control Automation Technology) is based on the IEEE 802.3 standard as one of the communication which is the I/O (Input/Output), sensors and communication function of PLC (Programmable Logic Controller) in industry and factory environment use is increasing. The Nuclear Safety Class Controller implemented by the EtherCAT applied bus can be shown the improving performance of data transmission in the controller.