WorldWideScience

Sample records for safety procedures manual

  1. Health and Safety Procedures Manual for hazardous waste sites

    Energy Technology Data Exchange (ETDEWEB)

    Thate, J.E.

    1992-09-01

    The Oak Ridge National Laboratory Chemical Assessments Team (ORNL/CAT) has developed this Health and Safety Procedures Manual for the guidance, instruction, and protection of ORNL/CAT personnel expected to be involved in hazardous waste site assessments and remedial actions. This manual addresses general and site-specific concerns for protecting personnel, the general public, and the environment from any possible hazardous exposures. The components of this manual include: medical surveillance, guidance for determination and monitoring of hazards, personnel and training requirements, protective clothing and equipment requirements, procedures for controlling work functions, procedures for handling emergency response situations, decontamination procedures for personnel and equipment, associated legal requirements, and safe drilling practices.

  2. HASL procedures manual

    International Nuclear Information System (INIS)

    Harley, J.H.

    1977-08-01

    Additions and corrections to the following sections of the HASL Procedures Manual are provided: General, Sampling, Field Measurements; General Analytical Chemistry, Chemical Procedures, Data Section, and Specifications

  3. HASL procedures manual

    International Nuclear Information System (INIS)

    1980-08-01

    Addition and corrections to the following sections of the HASL Procedures Manual are provided: Table of Contents; Bibliography; Fallout Collection Methods; Wet/Dry Fallout Collection; Fluoride in Soil and Sediment; Strontium-90; Natural Series; Alpha Emitters; and Gamma Emitters

  4. EML procedures manual

    International Nuclear Information System (INIS)

    Volchok, H.L.; de Planque, G.

    1982-01-01

    This manual contains the procedures that are used currently by the Environmental Measurements Laboratory of the US Department of Energy. In addition a number of analytical methods from other laboratories have been included. These were tested for reliability at the Battelle, Pacific Northwest Laboratory under contract with the Division of Biomedical and Environmental Research of the AEC. These methods are clearly distinguished. The manual is prepared in loose leaf form to facilitate revision of the procedures and inclusion of additional procedures or data sheets. Anyone receiving the manual through EML should receive this additional material automatically. The contents are as follows: (1) general; (2) sampling; (3) field measurements; (4) general analytical chemistry; (5) chemical procedures; (6) data section; (7) specifications

  5. Chemistry laboratory safety manual available

    Science.gov (United States)

    Elsbrock, R. G.

    1968-01-01

    Chemistry laboratory safety manual outlines safe practices for handling hazardous chemicals and chemistry laboratory equipment. Included are discussions of chemical hazards relating to fire, health, explosion, safety equipment and procedures for certain laboratory techniques and manipulations involving glassware, vacuum equipment, acids, bases, and volatile solvents.

  6. Health and safety manual

    International Nuclear Information System (INIS)

    1980-02-01

    The manual consists of the following chapters: general policies and administration; the Environmental Health and Safety Department; the Medical Services Department: biological hazards; chemical safety; confined space entry; cryogenic safety; electrical safety; emergency plans; engineering and construction; evacuations, trenching, and shoring; fire safety; gases, flammable and compressed; guarding, mechanical; ladders and scaffolds, work surfaces; laser safety; materials handling and storage; noise; personal protective equipment; pressure safety; radiation safety, ionizing and non-ionizing; sanitation; seismic safety; training, environmental health and safety; tools, power and hand-operated; traffic and transportation; and warning signs and devices

  7. Sodium safety manual

    International Nuclear Information System (INIS)

    Hayes, D.J.; Gardiner, R.L.

    1980-09-01

    The sodium safety manual is based upon more than a decade of experience with liquid sodium at Berkeley Nuclear Laboratories (BNL). It draws particularly from the expertise and experience developed in the course of research work into sodium fires and sodium water reactions. It draws also on information obtained from the UKAEA and other sodium users. Many of the broad principles will apply to other Establishments but much of the detail is specific to BNL and as a consequence its application at other sites may well be limited. Accidents with sodium are at best unpleasant and at worst lethal in an extremely painful way. The object of this manual is to help prevent sodium accidents. It is not intended to give detailed advice on specific precautions for particular situations, but rather to set out the overall strategy which will ensure that sodium activities will be pursued safely. More detail is generally conveyed to staff by the use of local instructions known as Sodium Working Procedures (SWP's) which are not reproduced in this manual although a list of current SWP's is included. Much attention is properly given to the safe design and operation of larger facilities; nevertheless evidence suggests that sodium accidents most frequently occur in small-scale work particularly in operations associated with sodium cleaning and special care is needed in all such cases. (U.K.)

  8. Regulations and Procedures Manual

    Energy Technology Data Exchange (ETDEWEB)

    Young, Lydia J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2011-07-25

    The purpose of the Regulations and Procedures Manual (RPM) is to provide LBNL personnel with a reference to University and Lawrence Berkeley National Laboratory (LBNL or Laboratory) policies and regulations by outlining normal practices and answering most policy questions that arise in the day-to-day operations of Laboratory organizations. Much of the information in this manual has been condensed from detail provided in LBNL procedure manuals, Department of Energy (DOE) directives, and Contract DE-AC02-05CH11231. This manual is not intended, however, to replace any of those documents. RPM sections on personnel apply only to employees who are not represented by unions. Personnel policies pertaining to employees represented by unions may be found in their labor agreements. Questions concerning policy interpretation should be directed to the LBNL organization responsible for the particular policy. A link to the Managers Responsible for RPM Sections is available on the RPM home page. If it is not clear which organization is responsible for a policy, please contact Requirements Manager Lydia Young or the RPM Editor.

  9. Regulations and Procedures Manual

    Energy Technology Data Exchange (ETDEWEB)

    Young, Lydia [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2010-09-30

    The purpose of the Regulations and Procedures Manual (RPM) is to provide Laboratory personnel with a reference to University and Lawrence Berkeley National Laboratory policies and regulations by outlining the normal practices and answering most policy questions that arise in the day-to-day operations of Laboratory departments. Much of the information in this manual has been condensed from detail provided in Laboratory procedure manuals, Department of Energy (DOE) directives, and Contract DE-AC02-05CH11231. This manual is not intended, however, to replace any of those documents. The sections on personnel apply only to employees who are not represented by unions. Personnel policies pertaining to employees represented by unions may be found in their labor agreements. Questions concerning policy interpretation should be directed to the department responsible for the particular policy. A link to the Managers Responsible for RPM Sections is available on the RPM home page. If it is not clear which department should be called, please contact the Associate Laboratory Director of Operations.

  10. Idaho Safety Manual.

    Science.gov (United States)

    Idaho State Dept. of Education, Boise. Div. of Vocational Education.

    This manual is intended to help teachers, administrators, and local school boards develop and institute effective safety education as a part of all vocational instruction in the public schools of Idaho. This guide is organized in 13 sections that cover the following topics: introduction to safety education, legislation, levels of responsibility,…

  11. Missouri Highway Safety Manual Recalibration

    Science.gov (United States)

    2018-05-01

    The Highway Safety Manual (HSM) is a national manual for analyzing the highway safety of various facilities, including rural roads, urban arterials, freeways, and intersections. The HSM was first published in 2010, and a 2014 supplement addressed fre...

  12. Construction inspection manual of procedures

    Science.gov (United States)

    2009-01-01

    This manual provides highway construction personnel with relevant, practical information in order to perform accurate inspections and provide relevant construction procedural information for the various roadway and structures items of work. It is the...

  13. Surface Environmental Surveillance Procedures Manual

    Energy Technology Data Exchange (ETDEWEB)

    Hanf, RW; Dirkes, RL

    1990-02-01

    This manual establishes the procedures for the collection of environmental samples and the performance of radiation surveys and other field measurements. Responsibilities are defined for those personnel directly involved in the collection of samples and the performance of field measurements.

  14. Surface Environmental Surveillance Procedures Manual

    International Nuclear Information System (INIS)

    Hanf, Robert W.; Poston, Ted M.

    2000-01-01

    Shows and explains certain procedures needed for surface environmental surveillance. Hanford Site environmental surveillance is conducted by the Pacific Northwest National Laboratory (PNNL) for the U.S. Department of Energy (DOE) under the Surface Environmental Surveillance Project (SESP). The basic requirements for site surveillance are set fourth in DOE Order 5400.1, General Environmental Protection Program Requirements. Guidance for the SESP is provided in DOE Order 5484.1, Environmental Protection, Safety, and Health Protection Information Reporting Requirements and DOE Order 5400.5, Radiation Protection of the Public and Environment. Guidelines for environmental surveillance activities are provided in DOE/EH-0173T, Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance. An environmental monitoring plan for the Hanford Site is outlined in DOE/RL 91-50 Rev. 2, Environmental Monitoring Plan, United States Department of Energy, Richland Operations Office. Environmental surveillance data are used in assessing the impact of current and past site operations on human health and the environment, demonstrating compliance with applicable local, state, and federal environmental regulations, and verifying the adequacy of containment and effluent controls. SESP sampling schedules are reviewed, revised, and published each calendar year in the Hanford Site Environmental Surveillance Master Sampling Schedule. Environmental samples are collected by SESP staff in accordance with the approved sample collection procedures documented in this manual. Personnel training requirements are documented in SESP-TP-01 Rev.2, Surface Environmental Surveillance Project Training Program.

  15. Microbial ecology laboratory procedures manual NASA/MSFC

    Science.gov (United States)

    Huff, Timothy L.

    1990-01-01

    An essential part of the efficient operation of any microbiology laboratory involved in sample analysis is a standard procedures manual. The purpose of this manual is to provide concise and well defined instructions on routine technical procedures involving sample analysis and methods for monitoring and maintaining quality control within the laboratory. Of equal importance is the safe operation of the laboratory. This manual outlines detailed procedures to be followed in the microbial ecology laboratory to assure safety, analytical control, and validity of results.

  16. Surface Environmental Surveillance Procedures Manual

    Energy Technology Data Exchange (ETDEWEB)

    RW Hanf; TM Poston

    2000-09-20

    Environmental surveillance data are used in assessing the impact of current and past site operations on human health and the environment, demonstrating compliance with applicable local, state, and federal environmental regulations, and verifying the adequacy of containment and effluent controls. SESP sampling schedules are reviewed, revised, and published each calendar year in the Hanford Site Environmental Surveillance Master Sampling Schedule. Environmental samples are collected by SESP staff in accordance with the approved sample collection procedures documented in this manual.

  17. Pollutant Assessments Group procedures manual: Volume 2, Technical procedures

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    This is volume 2 of the manuals that describes the technical procedures currently in use by the Pollution Assessments Group. This manual incorporates new developments in hazardous waste assessment technology and administrative policy. Descriptions of the equipment, procedures and operations of such things as radiation detection, soil sampling, radionuclide monitoring, and equipment decontamination are included in this manual. (MB)

  18. Radiological Emergency Response Health and Safety Manual

    Energy Technology Data Exchange (ETDEWEB)

    D. R. Bowman

    2001-05-01

    This manual was created to provide health and safety (H&S) guidance for emergency response operations. The manual is organized in sections that define each aspect of H and S Management for emergency responses. The sections are as follows: Responsibilities; Health Physics; Industrial Hygiene; Safety; Environmental Compliance; Medical; and Record Maintenance. Each section gives guidance on the types of training expected for managers and responders, safety processes and procedures to be followed when performing work, and what is expected of managers and participants. Also included are generic forms that will be used to facilitate or document activities during an emergency response. These ensure consistency in creating useful real-time and archival records and help to prevent the loss or omission of information.

  19. Procedures manual for the Oak Ridge Electron Linear Accelerator

    International Nuclear Information System (INIS)

    Todd, H.A.

    1979-01-01

    The Procedures Manual for the Oak Ridge Electron Linear Accelerator contains specific information pertaining to operation and safety of the facility. Items such as the interlock system, radiation monitoring, emergency procedures, night shift and weekend operation, and maintenance are discussed in detail

  20. Tank farms criticality safety manual

    International Nuclear Information System (INIS)

    FORT, L.A.

    2003-01-01

    This document defines the Tank Farms Contractor (TFC) criticality safety program, as required by Title 10 Code of Federal Regulations (CFR-), Subpart 830.204(b)(6), ''Documented Safety Analysis'' (10 CFR- 830.204 (b)(6)), and US Department of Energy (DOE) 0 420.1A, Facility Safety, Section 4.3, ''Criticality Safety.'' In addition, this document contains certain best management practices, adopted by TFC management based on successful Hanford Site facility practices. Requirements in this manual are based on the contractor requirements document (CRD) found in Attachment 2 of DOE 0 420.1A, Section 4.3, ''Nuclear Criticality Safety,'' and the cited revisions of applicable standards published jointly by the American National Standards Institute (ANSI) and the American Nuclear Society (ANS) as listed in Appendix A. As an informational device, requirements directly imposed by the CRD or ANSI/ANS Standards are shown in boldface. Requirements developed as best management practices through experience and maintained consistent with Hanford Site practice are shown in italics. Recommendations and explanatory material are provided in plain type

  1. Environmental Measurements Laboratory (EML) procedures manual

    International Nuclear Information System (INIS)

    Chieco, N.A.; Bogen, D.C.; Knutson, E.O.

    1990-11-01

    Volume 1 of this manual documents the procedures and existing technology that are currently used by the Environmental Measurements Laboratory. A section devoted to quality assurance has been included. These procedures have been updated and revised and new procedures have been added. They include: sampling; radiation measurements; analytical chemistry; radionuclide data; special facilities; and specifications. 228 refs., 62 figs., 37 tabs. (FL)

  2. Environment, safety, and health manual, closeout report

    International Nuclear Information System (INIS)

    1975-12-01

    A coordination draft of the Environment, Safety, and Health (ES and H) manual was submitted on 2 September 1975. Comments provided by Operational Safety personnel were being incorporated by a task team when the effort was terminated on 31 October 1975. This report documents the development history of the manual and provides a status of the manual up to the time the efforts were discontinued. Also discussed are issues which effect completion of the manual. Additionally a plan for completion of the manual is suggested

  3. Highway Safety Program Manual: Volume 3: Motorcycle Safety.

    Science.gov (United States)

    National Highway Traffic Safety Administration (DOT), Washington, DC.

    Volume 3 of the 19-volume Highway Safety Program Manual (which provides guidance to State and local governments on preferred highway safety practices) concentrates on aspects of motorcycle safety. The purpose and specific objectives of a State motorcycle safety program are outlined. Federal authority in the highway safety area and general policies…

  4. Occupational Safety and Health Curriculum Manual.

    Science.gov (United States)

    Gourley, Frank A., Jr., Comp.

    With the enactment of the Occupational Safety and Health Act of 1970, the need for manpower development in the field of industrial safety and hygiene has resulted in the development of a broad based program in Occupational Safety and Health. The manual provides information to administrators and instructors on a program of study in this field for…

  5. Manual on brachytherapy. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1996-01-01

    This publication is part of practical radiation safety manual series for different fields of application aimed primarily at persons handling radiation sources on a daily routine basis, which could at same time be used by the competent authorities, supporting their efforts in the radiation protection training of workers or medical assistance personnel or helping on-site management to set up local radiation protection rules. It is dedicated to brachytherapy: its application and procedures guides

  6. Manual on maintenance of systems and components important to safety

    International Nuclear Information System (INIS)

    1986-01-01

    The Manual should serve as guidance at the plant management level for the maintenance of systems and components important to safety. It includes a detailed description of management systems, administrative controls and procedures. The Annexes contain examples of documents and practices adopted by Operating Organizations of some Member States. It is not the intention of this Manual to address the technical problem of how to maintain a particular component but rather to cover the programmatic aspects of maintenance. It also contains some aspects of surveillance and verification activities. The Manual makes only general statements about radiation protection provisions in connection with maintenance; detailed guidance can be found in other IAEA documents

  7. Safety Training: "Manual Handling" course in September

    CERN Multimedia

    Safety Training, HSE Unit

    2016-01-01

    The next "Manual Handling" course will be given, in French, on 26 September 2016. This course is designed for anyone required to carry out manual handling of loads in the course of their work.   The main objective of this course is to adopt and apply the basic principles of physical safety and economy of effort. There are places available. If you are interested in following this course, please fill an EDH training request via our catalogue. 

  8. Safety analysis procedures for PHWR

    International Nuclear Information System (INIS)

    Min, Byung Joo; Kim, Hyoung Tae; Yoo, Kun Joong

    2004-03-01

    The methodology of safety analyses for CANDU reactors in Canada, a vendor country, uses a combination of best-estimate physical models and conservative input parameters so as to minimize the uncertainty of the plant behavior predictions. As using the conservative input parameters, the results of the safety analyses are assured the regulatory requirements such as the public dose, the integrity of fuel and fuel channel, the integrity of containment and reactor structures, etc. However, there is not the comprehensive and systematic procedures for safety analyses for CANDU reactors in Korea. In this regard, the development of the safety analyses procedures for CANDU reactors is being conducted not only to establish the safety analyses system, but also to enhance the quality assurance of the safety assessment. In the first phase of this study, the general procedures of the deterministic safety analyses are developed. The general safety procedures are covered the specification of the initial event, selection of the methodology and accident sequences, computer codes, safety analysis procedures, verification of errors and uncertainties, etc. Finally, These general procedures of the safety analyses are applied to the Large Break Loss Of Coolant Accident (LBLOCA) in Final Safety Analysis Report (FSAR) for Wolsong units 2, 3, 4

  9. A manual of nuclear medicine procedures

    International Nuclear Information System (INIS)

    Das, B.K.; Noreen Norfaraheen Lee Abdullah

    2012-01-01

    Nuclear medicine is a fast growing specialty. The procedures provide quantitative parameters of organ functions required for modern practice of medicine. With the development of new machines and increased application of computer software, the procedures are under continuous change. Some procedures have become outdated or redundant while new methods have been introduced to enhance the quality of information obtained from a particular application. Although there are a few books published abroad to inform doctors and technical staff about the procedures, a comprehensive source to give quick information about how different test are performed, particularly the new developments and the expected outcome both in normal and abnormal cases has been a long felt need. The physician ordering a Nuclear Medicine test also needs to know what patient preparations are required for optimal results, how to satisfy the queries of the patient particularly in respect of radiation exposure which sometimes can be a major concern of the patient. This manual has been prepared not only to describe technical details of various procedures that are currently practiced in Nuclear Medicine, but also to provide quick information for the doctors and health care personnel on how to inform the patients about the investigation for which they are being referred and how to interpret the results. Since there is no such comprehensive book published yet in Asia including South-East Asia, it is likely to be in great demand in the region. All students of Master Degree, M.D., DRM, DMRIT, M.Sc. (Nuclear Medicine) and technologists already working in various diagnostic centers will likely buy this book. General practitioners and specialists who refer patients for different radioisotope investigations may find this book useful for quick reference. (author)

  10. Safety handling manual for high dose rate remote afterloading system

    International Nuclear Information System (INIS)

    1999-01-01

    This manual is mainly for safety handling of 192 Ir-RALS (remote afterloading system) of high dose rate and followings were presented: Procedure and document format for the RALS therapy and for handling of its radiation source with the purpose of prevention of human errors and unexpected accidents, Procedure for preventing errors occurring in the treatment schedule and operation, and Procedure and format necessary for newly introducing the system into a facility. Consistency was intended in the description with the quality assurance guideline for therapy with small sealed radiation sources made by JASTRO (Japan Society for Therapeutic Radiology and Oncology). Use of the old type 60 Co-RALS was pointed out to be a serious problem remained and its safety handling procedure was also presented. (K.H.)

  11. IAEA publishes first health and safety manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1959-01-15

    A 'Manual on the Safe Handling of Radioisotopes' was published in English on 15 Dec ember 1958 by the International Atomic Energy Agency. This is a comprehensive handbook of internationally compiled recommendations for users of radioisotopes. It covers organizational, medical and technical aspects of radiation safety practices. It is also the Agency's first technical publication. French, Russian and Spanish editions will appear shortly. The Manual should prove useful to all users of radioisotopes in industry, medicine, research, etc., but is directed mainly to small scale users who may not have access to other sources of information. The recommendations apply only to radioactivity surpassing the limit of 0,002 microcurie concentration per gram of material; or a total activity of more than 0,1 microcuries in the working areas; this limit is based on the most dangerous radioisotopes. The experts state that the limiting level might be higher for less dangerous isotopes, but recommend that all be treated as potentially dangerous. This would have educational value and avoid accidents caused by misidentification. The Manual also stressed that good radiation safety practices depend on effective organization and warns that even very competent workers sometimes ignore or forget important health and safety requirements.

  12. IAEA publishes first health and safety manual

    International Nuclear Information System (INIS)

    1959-01-01

    A 'Manual on the Safe Handling of Radioisotopes' was published in English on 15 Dec ember 1958 by the International Atomic Energy Agency. This is a comprehensive handbook of internationally compiled recommendations for users of radioisotopes. It covers organizational, medical and technical aspects of radiation safety practices. It is also the Agency's first technical publication. French, Russian and Spanish editions will appear shortly. The Manual should prove useful to all users of radioisotopes in industry, medicine, research, etc., but is directed mainly to small scale users who may not have access to other sources of information. The recommendations apply only to radioactivity surpassing the limit of 0,002 microcurie concentration per gram of material; or a total activity of more than 0,1 microcuries in the working areas; this limit is based on the most dangerous radioisotopes. The experts state that the limiting level might be higher for less dangerous isotopes, but recommend that all be treated as potentially dangerous. This would have educational value and avoid accidents caused by misidentification. The Manual also stressed that good radiation safety practices depend on effective organization and warns that even very competent workers sometimes ignore or forget important health and safety requirements

  13. DOE explosives safety manual. Revision 7

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-01

    This manual prescribes the Department of Energy (DOE) safety rules used to implement the DOE safety policy for operations involving explosives. This manual is applicable to all DOE facilities engaged in operations of development, manufacturing, handling, storage, transportation, processing, or testing of explosives, pyrotechnics and propellants, or assemblies containing these materials. The standards of this manual deal with the operations involving explosives, pyrotechnics and propellants, and the safe management of such operations. The design of all new explosives facilities shall conform to the requirements established in this manual and implemented in DOE 6430.1A, ``General Design Criteria Manual.`` It is not intended that existing physical facilities be changed arbitrarily to comply with these provisions, except as required by law. Existing facilities that do not comply with these standards may continue to be used for the balance of their functional life, as long as the current operation presents no significantly greater risk than that assumed when the facility was originally designed and it can be demonstrated clearly that a modification to bring the facility into compliance is not feasible. However, in the case of a major renovation, the facility must be brought into compliance with current standards. The standards are presented as either mandatory or advisory. Mandatory standards, denoted by the words ``shall,`` ``must,`` or ``will,`` are requirements that must be followed unless written authority for deviation is granted as an exemption by the DOE. Advisory standards denoted by ``should`` or ``may`` are standards that may be deviated from with a waiver granted by facility management.

  14. Development of an environmental safety case guidance manual

    International Nuclear Information System (INIS)

    Wellstead, Matthew John

    2014-01-01

    NDA RWMD is currently considering the scope, purpose and structure of a safety case manual that covers the development of nuclear operational, transport and environmental safety cases for a geological disposal facility in the United Kingdom. This paper considers the Environmental Safety Case (ESC) input into such a manual (herein referred to as the 'ESC Manual'), looking at the drivers and benefits that a guidance manual in this area may provide. (authors)

  15. Occupational safety manual. 4. rev. ed.

    International Nuclear Information System (INIS)

    Skiba, R.

    1979-01-01

    With the rapid technical development and increasing life expectancy, protection against occupational hazards has become a central economic and social problem. Consultants and others responsible for occupational safety should not only be interested in their work but also have sufficient basic knowledge. The complex subject is presented in a simplified and easily comprehensible manner, with particular regard to the practical side. The book is at the same time a textbook for basic training and a reference manual for the working practice. (orig./HP) [de

  16. Procedures manual for the ORNL Radiological Survey Activities (RASA) Program

    International Nuclear Information System (INIS)

    Myrick, T.E.; Berven, B.A.; Cottrell, W.D.; Goldsmith, W.A.; Haywood, F.F.

    1987-04-01

    The portion of the radiological survey program performed by ORNL is the subject of this Procedures Manual. The RASA group of the Health and Safety Research Division (HASRD) at ORNL is responsible for the planning, conducting, and reporting of the results of radiological surveys at specified sites and associated vicinity properties. The results of these surveys are used by DOE in determining the need for and extent of remedial actions. Upon completion of the necessary remedial actions, the ORNL-RASA group or other OOS contractor may be called upon to verify the effectiveness of the remedial action. Information from these postremedial action surveys is included as part of the data base used by DOE in certifying a site for unrestricted use

  17. Procedures manual for the ORNL Radiological Survey Activities (RASA) Program

    Energy Technology Data Exchange (ETDEWEB)

    Myrick, T.E.; Berven, B.A.; Cottrell, W.D.; Goldsmith, W.A.; Haywood, F.F.

    1987-04-01

    The portion of the radiological survey program performed by ORNL is the subject of this Procedures Manual. The RASA group of the Health and Safety Research Division (HASRD) at ORNL is responsible for the planning, conducting, and reporting of the results of radiological surveys at specified sites and associated vicinity properties. The results of these surveys are used by DOE in determining the need for and extent of remedial actions. Upon completion of the necessary remedial actions, the ORNL-RASA group or other OOS contractor may be called upon to verify the effectiveness of the remedial action. Information from these postremedial action surveys is included as part of the data base used by DOE in certifying a site for unrestricted use.

  18. Environment, safety and health progress assessment manual

    International Nuclear Information System (INIS)

    1992-12-01

    On June 27, 1989, the Secretary of Energy announced a 10-Point Initiative to strengthen environment, safety, and health (ES ampersand H) programs, and waste management activities at DOE production, research, and testing facilities. One of the points involved conducting dent Tiger Team Assessments of DOE operating facilities. The Office of Special independent Projects (OSP), EH-5, in the Office of the Assistant Secretary for Environment, Safety and Health, EH-1, was assigned the responsibility to conduct the Tiger Team Assessments. Through June 1992, a total of 35 Tiger Team Assessments were completed. The Secretary directed that Corrective Action Plans be developed and implemented to address the concerns identified by the Tiger Teams. In March 1991, the Secretary approved a plan for assessments that are ''more focused, concentrating on ES ampersand H management, ES ampersand H corrective actions, self-assessment programs, and root-cause related issues.'' In July 1991, the Secretary approved the initiation of ES ampersand H Progress Assessments, as a followup to the Tiger Team Assessments, and in the continuing effort to institutionalize the self-assessment process and line management accountability in the ES ampersand H areas. This manual documents the processes to be used to perform the ES ampersand H Progress Assessments. It was developed based upon the lessons learned from Tiger Team Assessments, the two pilot Progress Assessments, and Progress Assessments that have been completed. The manual will be updated periodically to reflect lessons learned or changes in policy

  19. TADS Needs Assessment Procedures Manual, Summer 1980.

    Science.gov (United States)

    Black, Talbot; And Others

    The TADS (Technical Assistance Development System) Needs Assessment Manual is designed to guide the comprehensive review of Handicapped Children's Early Education Program (HCEEP) demonstration projects in identifying technical assistance needs. An introduction reviews the TADS technical assistance model which includes program planning, needs…

  20. XML Syntax for Clinical Laboratory Procedure Manuals

    OpenAIRE

    Saadawi, Gilan; Harrison, James H.

    2003-01-01

    We have developed a document type description (DTD) in Extensable Markup Language (XML)1 for clinical laboratory procedures. Our XML syntax can adequately structure a variety of procedure types across different laboratories and is compatible with current procedure standards. The combination of this format with an XML content management system and appropriate style sheets will allow efficient procedure maintenance, distributed access, customized display and effective searching across a large b...

  1. Safety procedures for radiography works

    International Nuclear Information System (INIS)

    Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

    2004-01-01

    The following subjects are discussed - Work preparation: before exposure, during exposure, after work completion. Radiographic work at the open site: types of open sites, establishment of radiographic boundary, storage of radiographic equipment at sites. Safety procedures for radiography works; radiographic works in exposure room

  2. Operating procedures and safety culture

    International Nuclear Information System (INIS)

    Carnino, A.

    1993-01-01

    The development of new technologies in recent years has led to a tremendous increase in the information to be mastered by operators in industrial processes. The information at operators disposal both in routine situations and accidental ones needs to be well prepared and organized to ensure reliability and safety. The man-machine interface should give operators all the necessary and clear indications on the process status and evolution so that the operators can operate the installation through adequate procedures. Procedures represent the real interface and mode of action of the operators on the machine, and they are of prime importance. Although they are by essence quite different, the routine, accident, and emergency procedures have in common one attribute: They all require a good safety culture both in their development and their implementation. From the definition given by the members of the International Nuclear Safety Advisory Group (INSAG), open-quotes Safety culture is that assembly of characteristics and attitudes in organizations and individuals which establishes that, as an overriding priority, nuclear plant safety issues receive the attention warranted by their significance,close quotes one can see that two aspects are embedded, a collective attitude that in fact is reflected in the managerial framework and an individual one that is linked to personnel behavior and work practices

  3. Manual of functions, assignments, and responsibilities for nuclear safety: Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    1994-10-15

    The FAR Manual is a convenient easy-to-use collection of the functions, assignments, and responsibilities (FARs) of DOE nuclear safety personnel. Current DOE directives, including Orders, Secretary of Energy Notices, and other assorted policy memoranda, are the source of this information and form the basis of the FAR Manual. Today, the majority of FARs for DOE personnel are contained in DOE`s nuclear safety Orders. As these Orders are converted to rules in the Code of Federal Regulations, the FAR Manual will become the sole source for information relating to the functions, assignments, responsibilities of DOE nuclear safety personnel. The FAR Manual identifies DOE directives that relate to nuclear safety and the specific DOE personnel who are responsible for implementing them. The manual includes only FARs that have been extracted from active directives that have been approved in accordance with the procedures contained in DOE Order 1321.1B.

  4. Environment, safety and health progress assessment manual

    International Nuclear Information System (INIS)

    1992-12-01

    On June 27, 1989, the Secretary of Energy announced a 1O-Point Initiative to strengthen environment,safety, and health (ES ampersand H) programs, and waste management activities at involved conducting DOE production, research, and testing facilities. One of the points independent Tiger Team Assessments of DOE operating facilities. The Office of Special Projects (OSP), EH-5, in the Office of the Assistant Secretary for Environment, Safety and Health, EH-1, was assigned the responsibility to conduct the Tiger Team Assessments. Through June 1992, a total of 35 Tiger Team Assessments were completed. The Secretary directed that Corrective Action Plans be developed and implemented to address the concerns identified by the Tiger Teams. In March 1991, the Secretary approved a plan for assessments that are ''more focused, concentrating on ES ampersand H management, ES ampersand H corrective actions, self-assessment programs, and root-cause related issues.'' In July 1991, the Secretary approved the initiation of ES ampersand H Progress Assessments, as a followup to the Tiger Team Assessments, and in the continuing effort to institutionalize the self-assessment process and line management accountability in the ES ampersand H areas. This volume contains appendices to the Environment, Safety and Health Progress Assessment Manual

  5. Manual of use and accounting of radioactive material and procedures of radiological protection for nuclear medicine

    International Nuclear Information System (INIS)

    Chavez, Miguel

    1997-03-01

    This manual of use and accounting of material radioactive and procedures of radiological safety tries to facilitate workings of protection of material radioactive in services of medicine nuclear, during diagnosis (examinations with x-rays, or those that are made in nuclear medicine), or during the processing of diseases, mainly of the carcinomas (x-ray)

  6. The design of operating procedures manuals for nuclear power plants

    International Nuclear Information System (INIS)

    Bohr, E.; Preuss, W.; Reinartz, G.; Thau, G.

    1977-03-01

    This report describes the findings of a research on the desirable design of operating procedures manuals for nuclear power plants. The work was supported by a grant of the Federal Department of the Interior. Information was acquired from different sources. Interviews and discussions on manual design were carried out with manual users in nuclear power plants. Moreover, tasks carried out using procedures were either observed or, alternatively, the manner of using procedures was elicited by interviews. In addition, manual writers, managers from manufacturers and utilities, nuclear experts, and individuals involved in manual specification activities were interviewed. A major source of information has been the pertinent scientific and technical findings scattered in the literature on topics such as instructional technology, engineering psychology, psycholinguistics, and typography. A comprehensive bibliography is included. General rules are established on designing instructional material for use on the job, aiming at increasing their legability, comprehensibility, and suitability to guide human performance. The application of these rules to the design of individual operating procedures is demonstrated. Recommendations are given on the design, layout, development and implementation of manuals. (orig.) [de

  7. Unique safety manual for experimental personnel

    International Nuclear Information System (INIS)

    Busick, D.D.; Warren, G.J.

    1979-01-01

    Within a few months of the discovery of x-rays the first radiation injuries were reported (ta71). During the past thirty years both the number and complexity of x-ray analytical units have increased markedly. The world-wide number of incidents leading to severe injury has also increased. For analytical x-ray machines the need for engineered and administrative safeguards has long been recognized. At Stanford Synchrotron Radiation Laboratory (SSRL) the personnel protection system has been carefully designed to maximize safety and minimize experimental interference. However, all possible experimental configurations cannot be anticipated and some interference is to be expected. There are means by which safeguards can be substituted as long as these substitutions do not degrade the existing degree of safety. any substitutions must be evaluated by the Radiation Safety Committee, the SSRL staff and Operational Health Physics. Some studies have indicated that between fifty and ninety percent of serious radiation accidents are directly related to human errors, i.e., ignoring administrative proccedures, by-passing engineered safeguards or by inadequate training. Lindell has estimated the annual probability of serious injury to be about 1:100 per macchine. No matter what the real probability of serious injury is the personnel protection system should reduce this risk to a value that approaches zero. It is hoped that this manual will bring into sharper focus some of the more serious results of unnecessary risk taking. We also hope that it will convey the very real necessity for safeguards which may at times appear to be arbitrary and unnecessary impediments to experimental purposes

  8. 1983 EML Procedures Manual. 26th Edition

    International Nuclear Information System (INIS)

    Volchok, H.L.; de Planque, G.

    1983-01-01

    This document consists of page and section changes to the following HASL-300 procedures: fallout collection methods, radiochemical 90 Sr, atomic absorption-emission spectrophotometry of trace metals, precipitation and lake water samples, anions by ion chromatography, polynuclear aromatic hydrocarbons in sediments, Mn in saline precipitation samples, and Pb in saline precipitation samples

  9. Procedures manual for the Evaluated Nuclear Structure Data File

    International Nuclear Information System (INIS)

    Bhat, M.R.

    1987-10-01

    This manual is a collection of various notes, memoranda and instructions on procedures for the evaluation of data in the Evaluated Nuclear Structure Data File (ENSDF). They were distributed at different times over the past few years to the evaluators of nuclear structure data and some of them were not readily avaialble. Hence, they have been collected in this manual for ease of reference by the evaluators of the international Nuclear Structure and Decay Data (NSDD) network contribute mass-chains to the ENSDF. Some new articles were written specifically for this manual and others are reivsions of earlier versions

  10. Blood component fractionation: manual versus automatic procedures.

    Science.gov (United States)

    Pasqualetti, Daniela; Ghirardini, Alessandro; Cristina Arista, Maria; Vaglio, Stefania; Fakeri, Azis; Waldman, Alan A; Girelli, Gabriella

    2004-02-01

    Over the last few years, quality system requirements have been introduced for blood components. The necessary compliance with standard productions will have a considerable impact on Blood Banks. The introduction of automated methods is the most satisfactory means to meet these requirements for blood component preparation. A new device has been developed to automate the fractionation of blood into components. We evaluated the efficacy of this instrument as compared to manual methods. A total of 218 units of blood have been collected, into several different commercial blood bag systems (77 into standard quadruple bag systems, 141 into bag systems with integrated in line filters), and used to evaluate the universality of the instrument. Whole blood units were processed using the Top/Top system and the Compomat G4 (Fresenius HemoCare). A separate program protocol was developed for each kind of bag. Use of the Compomat G4 resulted in a statistically significant (pblood components, and has been shown adaptable to use with different blood bag systems.

  11. Manual of bioassay procedures for radionuclides

    International Nuclear Information System (INIS)

    Pleskach, S.; Petkau, A.

    1986-06-01

    A monitoring program is described by which atomic radiation workers ar monitored for internal contamination with radionuclides in the workplace. The program involves analytical procedures for measuring alpha, beta and gamma activity in biological specimens, usually urine. Radionuclides are identified by their characteristic radiation using liquid scintillation counting, and alpha, beta and gamma spectrometry. Examples of calculating the minimum detectable activity for specific radionuclides are given and used to derive call-in-criteria in accordance with which the different groups of workers are monitored each month

  12. Probabilistic safety analysis procedures guide

    International Nuclear Information System (INIS)

    Papazoglou, I.A.; Bari, R.A.; Buslik, A.J.

    1984-01-01

    A procedures guide for the performance of probabilistic safety assessment has been prepared for interim use in the Nuclear Regulatory Commission programs. The probabilistic safety assessment studies performed are intended to produce probabilistic predictive models that can be used and extended by the utilities and by NRC to sharpen the focus of inquiries into a range of tissues affecting reactor safety. This guide addresses the determination of the probability (per year) of core damage resulting from accident initiators internal to the plant and from loss of offsite electric power. The scope includes analyses of problem-solving (cognitive) human errors, a determination of importance of the various core damage accident sequences, and an explicit treatment and display of uncertainties for the key accident sequences. Ultimately, the guide will be augmented to include the plant-specific analysis of in-plant processes (i.e., containment performance) and the risk associated with external accident initiators, as consensus is developed regarding suitable methodologies in these areas. This guide provides the structure of a probabilistic safety study to be performed, and indicates what products of the study are essential for regulatory decision making. Methodology is treated in the guide only to the extent necessary to indicate the range of methods which is acceptable; ample reference is given to alternative methodologies which may be utilized in the performance of the study

  13. RTOD-photo operations and procedures manual

    Energy Technology Data Exchange (ETDEWEB)

    1966-03-15

    This document presents a survey of the EG&G NRDS photographic operation in four major sections and includes the work scope, procedures, some technical backgrounding and operational information. Two sections, Instrumentation and Photo Systems, include the areas of direct responsibilities while a section on Film Handling and Coordination and a section covering special information, pertinent to the project, are included to adequately complete this survey. The photographic group is housed in two trailers within the control point area at NRDS and from these trailers provides photographic support at a number of locations. Four camera bunkers, three camera towers, a kinescope system, a microfilm system and remote camera controls comprise the facilities that the group maintains and operates outside these trailers. The work load includes major items such as: motion picture coverage of the nuclear rocket engine tests, data record microfilming, kinescope recording, and documentary coverage of the company related operational responsibilities. In addition, a number of minor photographic services are extended, when required. The nature of the work, because of its importance within the research and development efforts at NRDS, requires optimum quality and efficiency throughout. The many procedures outlined here have been designed to satisfy these requirements.

  14. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis

    International Nuclear Information System (INIS)

    2016-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  15. 77 FR 51943 - Procedures for Safety Investigations

    Science.gov (United States)

    2012-08-28

    ... rule, Procedures for Safety Investigations, which published July 27, 2012 in the Federal Register, 77... DEFENSE NUCLEAR FACILITIES SAFETY BOARD 10 CFR Part 1708 Procedures for Safety Investigations AGENCY: Defense Nuclear Facilities Safety Board. ACTION: Proposed rule; extension of comment period...

  16. Evaluation of the computerized procedures Manual II (COPMA II)

    International Nuclear Information System (INIS)

    Converse, S.A.

    1995-11-01

    The purpose of this study was to evaluate the effects of a computerized procedure system, the Computerized Procedure Manual II (COPMA-II), on the performance and mental workload of licensed reactor operators. To evaluate COPMA-II, eight teams of two operators were trained to operate a scaled pressurized water reactor facility (SPWRF) with traditional paper procedures and with COPMA-II. Following training, each team operated the SPWRF under normal operating conditions with both paper procedures and COPMA-II. The teams then performed one of two accident scenarios with paper procedures, but performed the remaining accident scenario with COPMA-II. Performance measures and subjective estimates of mental workload were recorded for each performance trial. The most important finding of the study was that the operators committed only half as many errors during the accident scenarios with COPMA-II as they committed with paper procedures. However, time to initiate a procedure was fastest for paper procedures for accident scenario trials. For performance under normal operating conditions, there was no difference in time to initiate or to complete a procedure, or in the number of errors committed with paper procedures and with COPMA-II. There were no consistent differences in the mental workload ratings operators recorded for trials with paper procedures and COPMA-II

  17. Principles and Practices of Occupational Safety and Health: Administrator's Manual.

    Science.gov (United States)

    Occupational Safety and Health Administration, Washington, DC.

    The manual guides an instructor in conducting a training course for first-line supervisors to familiarize them with six aspects relating to the Occupational Safety and Health Act of 1970: (1) requirements of the Act, (2) compliance with its standards, (3) identification of health and safety hazards, (4) correction of adverse conditions, (5) record…

  18. Manual on gamma radiography. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1996-01-01

    This publication is part of practical radiation safety manual series for different fields of application aimed primarily at persons handling radiation sources on a daily routine basis, which could at same time be used by the competent authorities, supporting their efforts in the radiation protection training of workers or medical assistance personnel or helping on-site management to set up local radiation protection rules. It is dedicated to gamma radiography: its application and procedures guides

  19. Manual on therapeutic uses of iodine-131. Incorporating: Applications guide, procedures guide, basics guide

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This publication is part of practical radiation safety manual series for different fields of application aimed primarily at persons handling radiation sources on a daily routine basis, which could at same time be used by the competent authorities, supporting their efforts in the radiation protection training of workers or medical assistance personnel or helping on-site management to set up local radiation protection rules. It is dedicated to therapeutic uses of Iodine-131: its application and procedures guides.

  20. Manual on high energy teletherapy. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1996-01-01

    This publication is part of practical radiation safety manual series for different fields of application aimed primarily at persons handling radiation sources on a daily routine basis, which could at same time be used by the competent authorities, supporting their efforts in the radiation protection training of workers or medical assistance personnel or helping on-site management to set up local radiation protection rules. It is dedicated to high energy radiotherapy: its application and procedures guides

  1. Manual on shielded enclosures. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1996-01-01

    This publication is part of practical radiation safety manual series for different fields of application aimed primarily at persons handling radiation sources on a daily routine basis, which could at same time be used by the competent authorities, supporting their efforts in the radiation protection training of workers or medical assistance personnel or helping on-site management to set up local radiation protection rules. It is dedicated to shielding enclosures: their application and procedures guides

  2. Manual on therapeutic uses of iodine-131. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1996-01-01

    This publication is part of practical radiation safety manual series for different fields of application aimed primarily at persons handling radiation sources on a daily routine basis, which could at same time be used by the competent authorities, supporting their efforts in the radiation protection training of workers or medical assistance personnel or helping on-site management to set up local radiation protection rules. It is dedicated to therapeutic uses of Iodine-131: its application and procedures guides

  3. Manual on nuclear gauges. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1996-01-01

    This publication is part of practical radiation safety manual series for different fields of application aimed primarily at persons handling radiation sources on a daily routine basis, which could at same time be used by the competent authorities, supporting their efforts in the radiation protection training of workers or medical assistance personnel or helping on-site management to set up local radiation protection rules. It is dedicated to nuclear gauges: their application and procedures guides

  4. Radiological survey activities: uranium mill tailings remedial action project procedures manual

    International Nuclear Information System (INIS)

    Little, C.A.; Berven, B.A.; Carter, T.E.

    1986-07-01

    The US Department of Energy (DOE) was assigned the responsibility for conducting remedial action at 24 sites, which are located in one eastern and nine western states. The DOE's responsibilities are being met through its Uranium Mill Tailings Remedial Action Project Office (UMTRA-PO) in Albuquerque, New Mexico. The purpose of this Procedures Manual is to provide a standardized set of procedures that document in an auditable manner the activities performed by the Radiological Survey Activities (RASA) group in the Dosimetry and Biophysical Transport Section (DABTS) of the Health and Safety Research Division (HASRD) at the Oak Ridge National Laboratory (ORNL), in its role as the Inclusion Survey Contractor (ISC). Members of the RASA group assigned to the UMTRA Project are headquartered in the ORNL/RASA office in Grand Junction, Colorado, and report to the ORNL/RASA Project Manager. The Procedures Manual ensures that the organizational, administrative, and technical activities of the RASA/UMTRA group conform properly to those of the ISC as described in the Vicinity Properties Management and Implementation Manual and the Summary Protocol. This manual also ensures that the techniques and procedures used by the RASA/UMTRA group and contractor personnel meet the requirements of applicable governmental, scientific, and industrial standards

  5. Federal Radiological Monitoring and Assessment Center Health and Safety Manual

    Energy Technology Data Exchange (ETDEWEB)

    FRMAC Health and Safety Working Group

    2012-03-20

    This manual is a tool to provide information to all responders and emergency planners and is suggested as a starting point for all organizations that provide personnel/assets for radiological emergency response. It defines the safety requirements for the protection of all emergency responders. The intent is to comply with appropriate regulations or provide an equal level of protection when the situation makes it necessary to deviate. In the event a situation arises which is not addressed in the manual, an appropriate management-level expert will define alternate requirements based on the specifics of the emergency situation. This manual is not intended to pertain to the general public.

  6. Health and Safety Audit Design Manual

    Energy Technology Data Exchange (ETDEWEB)

    Ternes, Mark P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Langley, Brandon R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Accawi, Gina K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Malhotra, Mini [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-10-01

    The Health and Safety Audit is an electronic audit tool developed by the Oak Ridge National Laboratory to assist in the identification and selection of health and safety measures when a home is being weatherized (i.e., receiving home energy upgrades), especially as part of the US Department of Energy (DOE) Weatherization Assistance Program, or during home energy-efficiency retrofit or remodeling jobs. The audit is specifically applicable to existing single-family homes (including mobile homes), and is generally applicable to individual dwelling units in low-rise multifamily buildings. The health and safety issues covered in the audit are grouped in nine categories: mold and moisture, lead, radon, asbestos, formaldehyde and volatile organic compounds (VOCs), combustion, pest infestation, safety, and ventilation. Development of the audit was supported by the US Department of Housing and Urban Development Office of Healthy Homes and Lead Hazard Control and the DOE Weatherization Assistance Program.

  7. Highway Safety Program Manual: Volume 8: Alcohol in Relation to Highway Safety.

    Science.gov (United States)

    National Highway Traffic Safety Administration (DOT), Washington, DC.

    Volume 8 of the 19-volume Highway Safety Program Manual (which provides guidance to State and local governments on preferred highway safety practices) concentrates on alcohol in relation to highway safety. The purpose and objectives of the alcohol program are outlined. Federal authority in the area of highway safety and general policies regarding…

  8. Load research manual. Volume 1. Load research procedures

    Energy Technology Data Exchange (ETDEWEB)

    Brandenburg, L.; Clarkson, G.; Grund, Jr., C.; Leo, J.; Asbury, J.; Brandon-Brown, F.; Derderian, H.; Mueller, R.; Swaroop, R.

    1980-11-01

    This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. In Volumes 1 and 2, procedures are suggested for determining data requirements for load research, establishing the size and customer composition of a load survey sample, selecting and using equipment to record customer electricity usage, processing data tapes from the recording equipment, and analyzing the data. Statistical techniques used in customer sampling are discussed in detail. The costs of load research also are estimated, and ongoing load research programs at three utilities are described. The manual includes guides to load research literature and glossaries of load research and statistical terms.

  9. Nuclear criticality safety. Chapter 0530 of AEC manual

    International Nuclear Information System (INIS)

    2006-01-01

    The programme objectives of this chapter of the U.S. Atomic Energy Commission manual on nuclear criticality safety are to protect the health and safety of the public and of the government and contractor personnel working in plants that handle fissionable material and to protect public and private property from the consequences of a criticality accident occurring in AEC-owned plants and other AEC-contracted activities involving fissionable materials

  10. Tritium radioluminescent devices, Health and Safety Manual

    Energy Technology Data Exchange (ETDEWEB)

    Traub, R.J.; Jensen, G.A.

    1995-06-01

    This document consolidates available information on the properties of tritium, including its environmental chemistry, its health physics, and safe practices in using tritium-activated RL lighting. It also summarizes relevant government regulations on RL lighting. Chapters are divided into a single-column part, which provides an overview of the topic for readers simply requiring guidance on the safety of tritium RL lighting, and a dual-column part for readers requiring more technical and detailed information.

  11. Tritium radioluminescent devices, Health and Safety Manual

    International Nuclear Information System (INIS)

    Traub, R.J.; Jensen, G.A.

    1995-06-01

    This document consolidates available information on the properties of tritium, including its environmental chemistry, its health physics, and safe practices in using tritium-activated RL lighting. It also summarizes relevant government regulations on RL lighting. Chapters are divided into a single-column part, which provides an overview of the topic for readers simply requiring guidance on the safety of tritium RL lighting, and a dual-column part for readers requiring more technical and detailed information

  12. Helicopter Operations and Personnel Safety (Helirescue Manual). Fourth Edition.

    Science.gov (United States)

    Dalle-Molle, John

    The illustrated manual includes information on various aspects of helicopter rescue missions, including mission management roles for key personnel, safety rules around helicopters, requests for helicopter support, sample military air support forms, selection of landing zones, helicopter evacuations, rescuer delivery, passenger unloading, crash…

  13. Importance of the documentation of the manual of quality and procedures handbook in the nuclear technology center

    International Nuclear Information System (INIS)

    Domech More, J.; Bolanos Hernandez, R.; Quitero Rosello, R.; Fernandez Rondon, M.; Milian Lorenzo, D.; Rodriguez Gual, M.

    1997-01-01

    In the present work is presented the methodology used for the elaboration of manual of quality of the Nuclear Technology Center and the technical Procedures Handbook for the execution of Preliminary Safety report of the Juragua Nuclear Power Plant, as well as the importance that has this documentation for the work of the center

  14. 77 FR 44174 - Procedures for Safety Investigations

    Science.gov (United States)

    2012-07-27

    ... of safety investigations. The rule is intended to state clearly the Board's policy and procedures for... statutory authority, when appropriate, following standard safety investigation policies, practices, and... has adhered to the regulatory philosophy and the applicable principles of regulation as set forth in...

  15. Vault Safety and Inventory System users manual, PRIME 2350. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Downey, N.J.

    1994-12-14

    This revision is issued to request review of the attached document: VSIS User Manual, PRIME 2350, which provides user information for the operation of the VSIS (Vault Safety and Inventory System). It describes operational aspects of Prime 2350 minicomputer and vault data acquisition equipment. It also describes the User`s Main Menu and menu functions, including REPORTS. Also, system procedures for the Prime 2350 minicomputer are covered.

  16. Vault Safety and Inventory System users manual, PRIME 2350. Revision 1

    International Nuclear Information System (INIS)

    Downey, N.J.

    1994-01-01

    This revision is issued to request review of the attached document: VSIS User Manual, PRIME 2350, which provides user information for the operation of the VSIS (Vault Safety and Inventory System). It describes operational aspects of Prime 2350 minicomputer and vault data acquisition equipment. It also describes the User's Main Menu and menu functions, including REPORTS. Also, system procedures for the Prime 2350 minicomputer are covered

  17. Radiation safety in nuclear medicine procedures

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Sang Geon; Kim, Ja Hae; Song, Ho Chun [Dept. of Nuclear Medicine, Medical Radiation Safety Research Center, Chonnam National University Hospital, Gwangju (Korea, Republic of)

    2017-03-15

    Since the nuclear disaster at the Fukushima Daiichi Nuclear Power Plant in 2011, radiation safety has become an important issue in nuclear medicine. Many structured guidelines or recommendations of various academic societies or international campaigns demonstrate important issues of radiation safety in nuclear medicine procedures. There are ongoing efforts to fulfill the basic principles of radiation protection in daily nuclear medicine practice. This article reviews important principles of radiation protection in nuclear medicine procedures. Useful references, important issues, future perspectives of the optimization of nuclear medicine procedures, and diagnostic reference level are also discussed.

  18. Radiation safety in nuclear medicine procedures

    International Nuclear Information System (INIS)

    Cho, Sang Geon; Kim, Ja Hae; Song, Ho Chun

    2017-01-01

    Since the nuclear disaster at the Fukushima Daiichi Nuclear Power Plant in 2011, radiation safety has become an important issue in nuclear medicine. Many structured guidelines or recommendations of various academic societies or international campaigns demonstrate important issues of radiation safety in nuclear medicine procedures. There are ongoing efforts to fulfill the basic principles of radiation protection in daily nuclear medicine practice. This article reviews important principles of radiation protection in nuclear medicine procedures. Useful references, important issues, future perspectives of the optimization of nuclear medicine procedures, and diagnostic reference level are also discussed

  19. The Alaska Commercial Fisheries Water Quality Sampling Methods and Procedures Manual

    Energy Technology Data Exchange (ETDEWEB)

    Folley, G.; Pearson, L.; Crosby, C. [Alaska Dept. of Environmental Conservation, Soldotna, AK (United States); DeCola, E.; Robertson, T. [Nuka Research and Planning Group, Seldovia, AK (United States)

    2006-07-01

    A comprehensive water quality sampling program was conducted in response to the oil spill that occurred when the M/V Selendang Ayu ship ran aground near a major fishing port at Unalaska Island, Alaska in December 2004. In particular, the sampling program focused on the threat of spilled oil to the local commercial fisheries resources. Spill scientists were unable to confidently model the movement of oil away from the wreck because of limited oceanographic data. In order to determine which fish species were at risk of oil contamination, a real-time assessment of how and where the oil was moving was needed, because the wreck became a continual source of oil release for several weeks after the initial grounding. The newly developed methods and procedures used to detect whole oil during the sampling program will be presented in the Alaska Commercial Fisheries Water Quality Sampling Methods and Procedures Manual which is currently under development. The purpose of the manual is to provide instructions to spill managers while they try to determine where spilled oil has or has not been encountered. The manual will include a meaningful data set that can be analyzed in real time to assess oil movement and concentration. Sections on oil properties and processes will be included along with scientific water quality sampling methods for whole and dissolved phase oil to assess potential contamination of commercial fishery resources and gear in Alaska waters during an oil spill. The manual will present a general discussion of factors that should be considered when designing a sampling program after a spill. In order to implement Alaska's improved seafood safety measures, the spatial scope of spilled oil must be known. A water quality sampling program can provide state and federal fishery managers and food safety inspectors with important information as they identify at-risk fisheries. 11 refs., 7 figs.

  20. Improvement of Safety Features in Standard Operation Procedure of Tc-99m Generator

    International Nuclear Information System (INIS)

    Manisah Saedon; Mohd Khairul Hakimi; Shyen, A.K.S.

    2011-01-01

    This paper describes the improvements proposed to the original production procedures for Tc-99m generators. Improvements are intended to add safety and health features for workers into the existing procedures. The difference between the new safe work procedures from the original work procedures; is the concern about the safety and health of employees other than the product safety. One of the suggested safety characteristics is by using the visual aid so that the workers can easily see and read the procedures when they perform their duties, whereas the previous procedures are kept in the manual and difficult to access. The purpose of this paper is to share information about the importance of safety and health features for the workers in the procedures established in addition to provide awareness to all parties involved. (author)

  1. Aviation Safety Reporting System: Process and Procedures

    Science.gov (United States)

    Connell, Linda J.

    1997-01-01

    The Aviation Safety Reporting System (ASRS) was established in 1976 under an agreement between the Federal Aviation Administration (FAA) and the National Aeronautics and Space Administration (NASA). This cooperative safety program invites pilots, air traffic controllers, flight attendants, maintenance personnel, and others to voluntarily report to NASA any aviation incident or safety hazard. The FAA provides most of the program funding. NASA administers the program, sets its policies in consultation with the FAA and aviation community, and receives the reports submitted to the program. The FAA offers those who use the ASRS program two important reporting guarantees: confidentiality and limited immunity. Reports sent to ASRS are held in strict confidence. More than 350,000 reports have been submitted since the program's beginning without a single reporter's identity being revealed. ASRS removes all personal names and other potentially identifying information before entering reports into its database. This system is a very successful, proof-of-concept for gathering safety data in order to provide timely information about safety issues. The ASRS information is crucial to aviation safety efforts both nationally and internationally. It can be utilized as the first step in safety by providing the direction and content to informed policies, procedures, and research, especially human factors. The ASRS process and procedures will be presented as one model of safety reporting feedback systems.

  2. A feasibility study for Arizona's roadway safety management process using the Highway Safety Manual and SafetyAnalyst : final report.

    Science.gov (United States)

    2016-07-01

    To enable implementation of the American Association of State Highway Transportation (AASHTO) Highway Safety Manual using : SaftetyAnalyst (an AASHTOWare software product), the Arizona Department of Transportation (ADOT) studied the data assessment :...

  3. Manual for the GAW Precipitation Chemistry Programme: Guidelines, Data Quality Objectives and Standard Operating Procedures

    National Research Council Canada - National Science Library

    Allan, Mary A

    2004-01-01

    This is a manual for the Global Atmosphere Watch Precipitation Chemistry (GAW-PC) Programme. Where possible, it describes standard operating procedures and otherwise provides guidance on methods and procedures...

  4. Operating procedure automation to enhance safety of nuclear power plants

    International Nuclear Information System (INIS)

    Husseiny, A.A.; Sabri, Z.A.; Adams, S.K.; Rodriguez, R.J.; Packer, D.; Holmes, J.W.

    1989-01-01

    Use of logic statements and computer assist are explored as means for automation and improvement on design of operating procedures including those employed in abnormal and emergency situations. Operating procedures for downpower and loss of forced circulation are used for demonstration. Human-factors analysis is performed on generic emergency operating procedures for three strategies of control; manual, semi-automatic and automatic, using standard emergency operating procedures. Such preliminary analysis shows that automation of procedures is feasible provided that fault-tolerant software and hardware become available for design of the controllers. Recommendations are provided for tests to substantiate the promise of enhancement of plant safety. Adequate design of operating procedures through automation may alleviate several major operational problems of nuclear power plants. Also, automation of procedures is necessary for partial or overall automatic control of plants. Fully automatic operations are needed for space applications while supervised automation of land-based and offshore plants may become the thrust of new generation of nulcear power plants. (orig.)

  5. Manual on oil-gas industry waste utilization radioecological safety

    International Nuclear Information System (INIS)

    Kudryashev, V.A.; Lukashenko, S.N.; Tuleushev, A.Zh.; Marabaev, Zh.N.; Pasysaev, V.A.; Kayukov, P.G.; Kozhakhmetov, N.B.; Shevtsov, S.P.

    2003-01-01

    The development of a new document - 'Manual on radio-ecologically safe utilization of waste from oil-and-gas production' is carried out. This document regulates the whole cycle of environment protection measures at waste utilization for the named industry in Kazakhstan and is aimed on lowering the radiation risks and assurance of radioecological safety both at present and for the future. The document presents a set regulations necessary for radioactive wastes handling in the oil-gas industry. The normative document was agreed in both the Ministry of Health of the Republic of Kazakhstan (RK) and Ministry of Environment Protection of RK

  6. Fire and blast safety manual for fuel element manufacture

    International Nuclear Information System (INIS)

    Ensinger, U.; Koehler, B.; Mester, W.; Riotte, H.G.; Sehrbrock, H.W.

    1988-01-01

    The manual aims to enable people involved in the planning, operation, supervision, licensing or appraisal of fuel element factories to make a quick and accurate assessment of blast safety. In Part A, technical plant principles are shown, and a summary lists the flammable materials and ignition sources to be found in fuel element factories, together with theoretical details of what happens during a fire or a blast. Part B comprises a list of possible fires and explosions in fuel element factories and ways of preventing them. Typical fire and explosion scenarios are analysed more closely on the basis of experiments. Part B also contains a list and an assessment of actual fires and explosions which have occurred in fuel element factories. Part C contains safety measures to protect against fire and explosion, in-built fire safety, fire safety in plant design, explosion protection and measures to protect people from radiation and other hazards when fighting fires. A distinction is drawn between UO 2 , MOX and HTR fuel elements. (orig./DG) [de

  7. Manual on panoramic gamma irradiators (categories 2 and 4). Incorporating: Applications guide, procedures guide, basics guide

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The document is the first revision of a previous one published in 1993 to provide guidance on the safe use and regulation of self-contained gamma irradiators (Co-60 or Cs-137 sources) in different fields of application. It includes three parts: Applications Guide, which describes the main applications of self-contained gamma irradiators, the type of equipment, including safety systems, operation and maintenance, and how to deal with incidents. Procedures Guide, which gives step by step instructions on how to carry out the practice. Basics Guide, which explains the fundamentals of radiation, the system of units, interaction of radiation with matter radiation detection, etc. The manual is aimed primarily at persons handling such radiation sources on a daily routine basis, as well as at the competent authorities for training of workers in radiation protection or for setting up local radiation protection rules.

  8. Manual on panoramic gamma irradiators (categories 2 and 4). Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1996-01-01

    The document is the first revision of a previous one published in 1993 to provide guidance on the safe use and regulation of self-contained gamma irradiators (Co-60 or Cs-137 sources) in different fields of application. It includes three parts: Applications Guide, which describes the main applications of self-contained gamma irradiators, the type of equipment, including safety systems, operation and maintenance, and how to deal with incidents. Procedures Guide, which gives step by step instructions on how to carry out the practice. Basics Guide, which explains the fundamentals of radiation, the system of units, interaction of radiation with matter radiation detection, etc. The manual is aimed primarily at persons handling such radiation sources on a daily routine basis, as well as at the competent authorities for training of workers in radiation protection or for setting up local radiation protection rules

  9. The Radiological Safety Analysis Computer Program (RSAC-5) user's manual

    International Nuclear Information System (INIS)

    Wenzel, D.R.

    1994-02-01

    The Radiological Safety Analysis Computer Program (RSAC-5) calculates the consequences of the release of radionuclides to the atmosphere. Using a personal computer, a user can generate a fission product inventory from either reactor operating history or nuclear criticalities. RSAC-5 models the effects of high-efficiency particulate air filters or other cleanup systems and calculates decay and ingrowth during transport through processes, facilities, and the environment. Doses are calculated through the inhalation, immersion, ground surface, and ingestion pathways. RSAC+, a menu-driven companion program to RSAC-5, assists users in creating and running RSAC-5 input files. This user's manual contains the mathematical models and operating instructions for RSAC-5 and RSAC+. Instructions, screens, and examples are provided to guide the user through the functions provided by RSAC-5 and RSAC+. These programs are designed for users who are familiar with radiological dose assessment methods

  10. Principles and Practices of Occupational Safety and Health: Student Manual: Booklet One.

    Science.gov (United States)

    Occupational Safety and Health Administration, Washington, DC.

    The manual is the first of six student manuals for use in a course on occupational health and safety for supervisory personnel. The manual contains lessons 1-3 of the 15 consecutively-numbered lessons, each of which contains study questions (and answers) interwoven with the text and review questions at the end of each section. Lesson 1 (three…

  11. Principles and Practices of Occupational Safety and Health: Student Manual: Booklet Five.

    Science.gov (United States)

    Occupational Safety and Health Administration, Washington, DC.

    The manual is the fifth of six student manuals for use in a course on occupational health and safety for supervisory personnel. The manual contains lessons 14 and 15 of the 15 consecutively-numbered lessons, each of which contains study questions (and answers) interwoven with the text and review questions at the end of each section. Lesson 14…

  12. Simplified Procedures for Eutrophication Assessment and Prediction: User Manual

    Science.gov (United States)

    1996-09-01

    1975), for use in the Lake Erie Wastewater Management Study and is described by Verhoff, Yaksich, and Melfi (1980) and Westerdahl et al. (1981). This...manual," Technical Re- port E-81-9, U.S. Army Engineer Waterways Experiment Station, Vicksburg, MS. Westerdahl , H. E., Ford, W. B., Harris, J., and

  13. Effluent-Monitoring Procedures: Basic Laboratory Skills. Student Reference Manual.

    Science.gov (United States)

    Engel, William T.; And Others

    This is one of several short-term courses developed to assist in the training of waste water treatment plant operational personnel in the tests, measurements, and report preparation required for compliance with their NPDES Permits. This Student Reference Manual provides a review of basic mathematics as it applies to the chemical laboratory. The…

  14. Information Manual: Procedures, Planning Concepts, Subsystems. ABS Publication No. 3.

    Science.gov (United States)

    California Univ., Berkeley.

    This report, the third in a series which presents the results of a systems analysis of the problem of providing science and engineering buildings at the university level, is a technical manual for using the Academic Building Systems (ABS) approach in programing, designing, and constructing such facilities. The document presents (1) planning…

  15. Transferring manual ultrasonic inspection procedures - results of a pilot study

    International Nuclear Information System (INIS)

    Anderson, M.; Taylor, T.; Kadenko, I.

    2002-01-01

    Results of a manual ultrasonic pilot study for NDE specialists at RBMK nuclear reactor sites are presented. Probabilities of detection and false calls, using two different grading criteria, are estimated. Analyses of performance parameters lead to conclusions regarding attributes for improved test discrimination capabilities. (orig.)

  16. Surface Environmental Surveillance Procedures Manual, PNL-MA-580, Rev. 5

    Energy Technology Data Exchange (ETDEWEB)

    Hanf, Robert W.; Poston, Ted M.; Bisping, Lynn E.

    2007-07-01

    This manual contains the procedures that are used for the collection of routine Surface Environmental Surveillance Project environmental samples and field measurements on and around the Hanford Site. Specific responsibilities for project personnel are also defined.

  17. Safety manual for civil engineering and building works of nuclear power plants

    International Nuclear Information System (INIS)

    1988-01-01

    This manual lays down the various important considerations that go into safe design of civil structures for nuclear power plants. This manual identifies the design approach, quality assurance requirements and acceptance criteria that need to be observed to assure safety. Considerations on civil design having bearing on safety, during decommissioning are also indicated. (original). 37 refs., tabs

  18. Survey Procedures Manual for the Environmental Survey and Site Assessment Program (ESSAP). Revision 10

    International Nuclear Information System (INIS)

    2000-01-01

    The Environmental Survey and Site Assessment Program (ESSAP) of the Oak Ridge Institute for Science and Education (ORISE) conducts radiological survey activities under a contract with the U. S. Department of Energy (DOE) and for the U.S. Nuclear Regulatory Commission (NRC). ORISE and its programs are operated by Oak Ridge Associated Universities (ORAU) through a contract with DOE. The purpose of this Procedures Manual is to provide a standardized set of procedures that document activities of the program in an auditable manner. These procedures are applicable to both DOE and NRC operations. Procedures presented in this manual are limited to those associated with site survey activities

  19. Manual on brachytherapy. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1992-01-01

    In addition to a basic guide to the principles of the production of ionizing radiation and to methods of radiation protection and dosimetry, this booklet includes information about radiation protection procedures for brachytherapy

  20. ODIN. Online Database Information Network: ODIN Policy & Procedure Manual.

    Science.gov (United States)

    Townley, Charles T.; And Others

    Policies and procedures are outlined for the Online Database Information Network (ODIN), a cooperative of libraries in south-central Pennsylvania, which was organized to improve library services through technology. The first section covers organization and goals, members, and responsibilities of the administrative council and libraries. Patrons…

  1. System Certification Procedures and Criteria Manual for Deep Submergence Systems

    Science.gov (United States)

    1973-07-01

    safety of the DSS personnel. Milestone Event Schedule A lit of sequential events in the certification process with estimated completion dates. Non...milestone event schedule should include a list of sequential events in the Certification process with estimated dates of completion. The time...valve lineup during flush and the direction of flow. In addition, if flushing blocks are used, the removed valve inter- nals should be cleaned in

  2. Laboratory Safety Manual for Alabama Schools. Bulletin 1975. No. 20.

    Science.gov (United States)

    Alabama State Dept. of Education, Montgomery.

    This document presents the Alabama State Department of Education guidelines for science laboratory safety, equipment, storage, chemical safety, rocket safety, electrical safety, safety with radioisotopes, and safety with biologicals. Also included is a brief bibliography, a teacher's checklist, a listing of laser facts and regulations, and a…

  3. National Economic Development Procedures Manual - Agricultural Flood Damage,

    Science.gov (United States)

    1987-10-01

    based on the conceptual framework of the Economic and Environmental Principles and Guidelines for Water and Related Land Resources Implementation...the planning process and the NED evaluacion ’- ". procedures for agriculture, as described in the P&G, are thei presented. Also identified are some...ood Ioss compu t at ion approach de ’(’ op4 t hie f I ond damage for hypothetical frequency flood events and weights the result to I V- II1. + . IV-11

  4. Manual licensing procedure co-fermentation of manure. Guideline for the initiator; Handboek vergunningverlening co-vergisting van mest. Wegwijzer voor de initiatiefnemer

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-11-15

    This manual helps licensers assess the opportunities and possible bottlenecks in applying for a license for a co-digester. The manual contains elaborate information on the safety of the co-digester, the influence on the environment, the smell, the noise and the transport movements. Moreover, the licensing procedure is explained [Dutch] Dit handboek helpt vergunningverleners bij het inschatten van de kansen en mogelijke knelpunten bij de aanvraag voor een co-vergister. Het handboek bevat uitgebreide informatie over de veiligheid van de co-vergister, de invloed op de omgeving, de geur, het geluid en transportbewegingen. Daarnaast komt de procedure rond de vergunningverlening aan bod.

  5. Highway Safety Manual applied in Missouri - freeway/software : research summary.

    Science.gov (United States)

    2016-03-01

    AASHTOs Highway Safety Manual (HSM) : includes models for freeway segments, speedchange : lanes (transitional area between mainline : and ramps), ramps, and interchange terminals. : These predictive models for freeway : interchanges need to be cal...

  6. Flaws found in Los Alamos safety procedures

    Science.gov (United States)

    Gwynne, Peter

    2017-12-01

    A US government panel on nuclear safety has discovered a series of safety issues at the Los Alamos National Laboratory, concluding that government oversight of the lab's emergency preparation has been ineffective.

  7. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis (Spanish Edition)

    International Nuclear Information System (INIS)

    2017-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  8. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis (French Edition)

    International Nuclear Information System (INIS)

    2017-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  9. Concrete containment integrity software: Procedure manual and guidelines

    International Nuclear Information System (INIS)

    Dameron, R.A.; Dunham, R.S.; Rashid, Y.R.

    1990-06-01

    This report is an executive summary describing the concrete containment analysis methodology and software that was developed in the EPRI-sponsored research to predict the overpressure behavior and leakage of concrete containments. A set of guidelines has been developed for performing reliable 2D axisymmetric concrete containment analysis with a cracking concrete constitutive model developed by ANATECH. The software package developed during this research phase is designed for use in conjunction with ABAQUS-EPGEN; it provides the concrete model and automates axisymmetric grid preparation, and rebar generation for 2D and 3D grids. The software offers the option of generating pre-programmed axisymmetric grids that can be tailored to a specific containment by input of a few geometry parameters. The goal of simplified axisymmetric analysis within the framework of the containment leakage prediction methodology is to compute global liner strain histories at various locations within the containment. A simplified approach for generating peak liner strains at structural discontinuities as function of the global liner strains has been presented in a separate leakage criteria document; the curves for strain magnification factors and liner stress triaxiality factors found in that document are intended to be applied to the global liner strain histories developed through global 2D analysis. This report summarizes the procedures for global 2D analysis and gives an overview of the constitutive model and the special purpose concrete containment analysis software developed in this research phase. 8 refs., 10 figs

  10. Development of manual procedures for care of pregnant patients in radiotherapy service

    International Nuclear Information System (INIS)

    Scarabino, M.L.; Ruggeri, R.M.; Colombo, S.; Mairal, L.; Sardi, M.E.

    2013-01-01

    The work involves the creation of a manual of procedures for the care of pregnant patients in a radiotherapy center in which each instance of treatment is included, from the obstetrician-oncology comprehensive assessment during admission to establishing controls newborn and its subsequent development in multidisciplinary team. For the preparation of the manual had to design an anthropomorphic phantom that resembles a pregnant woman, which was used to carry out internal and external dosimetry. In turn imparted calculations fetal doses using TPS, imaging tests with MRI, avoiding the use of the tomograph and adapted to the resonator involved were carried immobilizer. All experiences and progress made during the treated cases are introduced in the procedures manual, making it a dynamic tool for continuous improvement for the institution

  11. Manual on quality assurance for computer software related to the safety of nuclear power plants

    International Nuclear Information System (INIS)

    1988-01-01

    The objective of the Manual is to provide guidance in the assurance of quality of specification, design, maintenance and use of computer software related to items and activities important to safety (hereinafter referred to as safety related) in nuclear power plants. This guidance is consistent with, and supplements, the requirements and recommendations of Quality Assurance for Safety in Nuclear Power Plants: A Code of Practice, 50-C-QA, and related Safety Guides on quality assurance for nuclear power plants. Annex A identifies the IAEA documents referenced in the Manual. The Manual is intended to be of use to all those who, in any way, are involved with software for safety related applications for nuclear power plants, including auditors who may be called upon to audit management systems and product software. Figs

  12. The procedures manual of the Environmental Measurements Laboratory. Volume 1, 28. edition

    Energy Technology Data Exchange (ETDEWEB)

    Chieco, N.A. [ed.

    1997-02-01

    This manual covers procedures and technology currently in use at the Environmental Measurements Laboratory. An attempt is made to be sure that all work carried out will be of the highest quality. Attention is focused on the following areas: quality assurance; sampling; radiation measurements; analytical chemistry; radionuclide data; special facilities; and specifications.

  13. The procedures manual of the Environmental Measurements Laboratory. Volume 1, 28. edition

    International Nuclear Information System (INIS)

    Chieco, N.A.

    1997-02-01

    This manual covers procedures and technology currently in use at the Environmental Measurements Laboratory. An attempt is made to be sure that all work carried out will be of the highest quality. Attention is focused on the following areas: quality assurance; sampling; radiation measurements; analytical chemistry; radionuclide data; special facilities; and specifications

  14. Field Operations and Enforcement Manual for Air Pollution Control. Volume III: Inspection Procedures for Specific Industries.

    Science.gov (United States)

    Weisburd, Melvin I.

    The Field Operations and Enforcement Manual for Air Pollution Control, Volume III, explains in detail the following: inspection procedures for specific sources, kraft pulp mills, animal rendering, steel mill furnaces, coking operations, petroleum refineries, chemical plants, non-ferrous smelting and refining, foundries, cement plants, aluminum…

  15. Safety of Cargo Aircraft Handling Procedure

    Directory of Open Access Journals (Sweden)

    Daniel Hlavatý

    2017-07-01

    Full Text Available The aim of this paper is to get acquainted with the ways how to improve the safety management system during cargo aircraft handling. The first chapter is dedicated to general information about air cargo transportation. This includes the history or types of cargo aircraft handling, but also the means of handling. The second part is focused on detailed description of cargo aircraft handling, including a description of activities that are performed before and after handling. The following part of this paper covers a theoretical interpretation of safety, safety indicators and legislative provisions related to the safety of cargo aircraft handling. The fourth part of this paper analyzes the fault trees of events which might occur during handling. The factors found by this analysis are compared with safety reports of FedEx. Based on the comparison, there is a proposal on how to improve the safety management in this transportation company.

  16. Considerations to improve the safety of cervical spine manual therapy.

    Science.gov (United States)

    Hutting, Nathan; Kerry, Roger; Coppieters, Michel W; Scholten-Peeters, Gwendolijne G M

    2018-02-01

    Manipulation and mobilisation of the cervical spine are well established interventions in the management of patients with headache and/or neck pain. However, their benefits are accompanied by potential, yet rare risks in terms of serious adverse events, including neurovascular insult to the brain. A recent international framework for risk assessment and management offers directions in the mitigation of this risk by facilitating sound clinical reasoning. The aim of this article is to critically reflect on and summarize the current knowledge about cervical spine manual therapy and to provide guidance for clinical reasoning for cervical spine manual therapy. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Light Water Reactor Generic Safety Issues Database (LWRGSIDB). User's manual

    International Nuclear Information System (INIS)

    1999-01-01

    The IAEA Conference on 'The Safety of Nuclear Power: Strategy for the Future' in 1991 was a milestone in nuclear safety. The objective of this conference was to review nuclear power safety issues for which achieving international consensus would be desirable, to address concerns on nuclear safety and to formulate recommendations for future actions by national and international authorities to advance nuclear safety to the highest level. Two of the important items addressed by this conference were ensuring and enhancing safety of operating plants and treatment of nuclear power plants built to earlier safety standards. Some of the publications related to these two items that have been issued subsequent to this conference are: A Common Basis for Judging the Safety of Nuclear Power Plants Built to Earlier Standards, INSAG-8 (1995), the IAEA Safety Guide 50-SG-O12, Periodic Safety Review of Operational Nuclear Power Plants (1994) and IAEA Safety Reports Series No. 12, Evaluation of the Safety of Operating Nuclear Power Plants Built to Earlier Standards: A Common Basis for Judgement (1998). Some of the findings of the 1991 conference have not yet been fully addressed. An IAEA Symposium on Reviewing the Safety of Existing Nuclear Power Plants in 1996 showed that there is an urgent need for operating organizations and national authorities to review those operating nuclear power plants which do not reach the high safety levels of the vast majority of plants and to undertake improvements with assistance from the international community if required. Safety reviews of operating nuclear power plants take on added importance in the context of the Convention on Nuclear Safety and its implementation. In order to perform safety reviews and to reassess the safety of operating nuclear power plants in a uniform manner, it is imperative to have an internationally accepted reference. Existing guidance needs to be complemented by a list of safety issues which have been encountered and

  18. Trapping safety into rules how desirable or avoidable is proceduralization?

    CERN Document Server

    Bourrier, Mathilde

    2013-01-01

    Rules and procedures are key features for a modern organization to function. It is no surprise to see them to be paramount in safety management. As some sociologists argue, routine and rule following is not always socially resented. It can bring people comfort and reduce anxieties of newness and uncertainty. Facing constant unexpected events entails fatigue and exhaustion. There is also no doubt that proceduralization and documented activities have brought progress, avoided recurrent mistakes and allowed for 'best practices' to be adopted. However, it seems that the exclusive and intensive use of procedures today is in fact a threat to new progress in safety. There is an urgent need to consider this issue because there is doubt that the path chosen by many hazardous industries and activities is the most effective, safety wise, considering the safety level achieved today. As soon as safety is involved, there seems to be an irresistible push towards a wider scope of norms, procedures and processes, whatever the...

  19. Student manual, Book 2: Orientation to occupational safety compliance in DOE

    Energy Technology Data Exchange (ETDEWEB)

    Colley, D.L.

    1993-10-01

    This is a student hand-book an Occupational Safety Compliance in DOE. Topics include the following: Electrical; materials handling & storage; inspection responsibilities & procedures; general environmental controls; confined space entry; lockout/tagout; office safety, ergonomics & human factors; medical & first aid, access to records; construction safety; injury/illness reporting system; and accident investigation procedures.

  20. Student manual, Book 2: Orientation to occupational safety compliance in DOE

    International Nuclear Information System (INIS)

    Colley, D.L.

    1993-01-01

    This is a student hand-book an Occupational Safety Compliance in DOE. Topics include the following: Electrical; materials handling ampersand storage; inspection responsibilities ampersand procedures; general environmental controls; confined space entry; lockout/tagout; office safety, ergonomics ampersand human factors; medical ampersand first aid, access to records; construction safety; injury/illness reporting system; and accident investigation procedures

  1. Quality procedure management for improved nuclear safety

    International Nuclear Information System (INIS)

    Forzano, P.; Castagna, P.

    1995-01-01

    Emergency Operating Procedures and Accident Management Procedures are the next step in the computerization of NPP control rooms. Different improvements are presently conceivable for this operator aid tool, and research activities are in development. Undergoing activities regard especially formal aspects of knowledge representation, Human-Machine interface and procedure life cycle management. These aspects have been investigated deeply by Ansaldo, and partially incorporated in the DIAM prototype. Nuclear Power Plant Procedures can be seen from essentially two viewpoints: the process and the information management. From the first point of view, it is important to supply the knowledge apt to solve problems connected with the control of the process, from the second one the focus of attention is on the knowledge representation, its structure, elicitation and maintenance, and formal quality assurance. These two aspects of procedure representation can be considered and solved separately. In particular, methodological, formal and management issues require long and tedious activities, that in most cases constitute a great barrier for procedures development and upgrade. To solve these problems, Ansaldo is developing DIAM, a wide integrated tool for procedure management to support in procedure writing, updating, usage, and documentation. One of the most challenging features of DIAM is AUTO-LAY, a CASE sub-tool that, in a complete automatical way, structures parts or complete flow diagram. This is the feature that is partial present in some other CASE products, that, anyway, do not allow complex graph handling and isomorphism between video and paper representation. AUTO-LAY has the unique prerogative to draw graphs of any complexity to section them in pages, and to automatically compose a document. This has been recognized in the literature as the most important a second-generation CASE improvement. (Author) 9 Figs., 5 Refs

  2. Reliability assessment of a manual-based procedure towards learning curve modeling and fmea analysis

    Directory of Open Access Journals (Sweden)

    Gustavo Rech

    2013-03-01

    Full Text Available Separation procedures in drug Distribution Centers (DC are manual-based activities prone to failures such as shipping exchanged, expired or broken drugs to the customer. Two interventions seem as promising in improving the reliability in the separation procedure: (i selection and allocation of appropriate operators to the procedure, and (ii analysis of potential failure modes incurred by selected operators. This article integrates Learning Curves (LC and FMEA (Failure Mode and Effect Analysis aimed at reducing the occurrence of failures in the manual separation of a drug DC. LCs parameters enable generating an index to identify the recommended operators to perform the procedures. The FMEA is then applied to the separation procedure carried out by the selected operators in order to identify failure modes. It also deployed the traditional FMEA severity index into two sub-indexes related to financial issues and damage to company´s image in order to characterize failures severity. When applied to a drug DC, the proposed method significantly reduced the frequency and severity of failures in the separation procedure.

  3. Development of a health and safety manual for emergency response operations

    International Nuclear Information System (INIS)

    Riland, C.A.; Junio, S.S.

    2000-01-01

    The Federal Radiological Monitoring and Assessment Center (FRMAC) Health and Safety Manual, which has been under development by a multi-agency group, is nearing completion and publication. The manual applies to offsite monitoring during a radiological accident or incident. Though written for multi-agency offsite monitoring activities (FRMAC), the manual is generic in nature and should be readily adaptable for other emergency response operations. Health and safety issues for emergency response situations often differ from those of normal operations. Examples of these differences and methodologies to address these issues are discussed. Challenges in manual development, including lack of regulatory and guidance documentation, are also discussed. One overriding principle in the Health and Safety Manual development is the overall reduction of risk, not just dose. The manual is broken into several chapters, which include Overview of Responsibities, Health Physics, Industrial Hygiene and Safey, Medical, and Environmental Compliance and Records. Included is a series of appendices, which presents additional information on forms and plans for default scenarios

  4. Manual on self-contained gamma irradiators (categories 1 and 3). Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1996-01-01

    The document is the first revision of a previous one published in 1993 to provide guidance on the safe use and regulation of panoramic gamma irradiators (Co-60 or Cs-137 sources) in different fields of application. It includes three parts: Applications Guide, which describes the main applications of panoramic gamma irradiators, the type of equipment, including safety systems, operation and maintenance, and how to deal with incidents. Procedures Guide, which gives step by step instructions on how to carry out the practice. Basics Guide, which explains the fundamentals of radiation, the system of units, interaction of radiation with matter radiation detection, etc. and which is common to all documents in the series. The manual is aimed primarily at persons handling such radiation sources on a daily routine basis, as well as at the competent authorities for training of workers in radiation protection or for setting up local radiation protection rules

  5. The impact of a medical procedure service on patient safety, procedure quality and resident training opportunities.

    Science.gov (United States)

    Tukey, Melissa H; Wiener, Renda Soylemez

    2014-03-01

    At some academic hospitals, medical procedure services are being developed to provide supervision for residents performing bedside procedures in hopes of improving patient safety and resident education. There is limited knowledge of the impact of such services on procedural complication rates and resident procedural training opportunities. To determine the impact of a medical procedure service (MPS) on patient safety and resident procedural training opportunities. Retrospective cohort analysis comparing characteristics and outcomes of procedures performed by the MPS versus the primary medical service. Consecutive adults admitted to internal medicine services at a large academic hospital who underwent a bedside medical procedure (central venous catheterization, thoracentesis, paracentesis, lumbar puncture) between 1 July 2010 and 31 December 2011. The primary outcome was a composite rate of major complications. Secondary outcomes included resident participation in bedside procedures and use of "best practice" safety process measures. We evaluated 1,707 bedside procedures (548 by the MPS, 1,159 by the primary services). There were no differences in the composite rate of major complications (1.6 % vs. 1.9 %, p = 0.71) or resident participation in bedside procedures (57.0 % vs. 54.3 %, p = 0.31) between the MPS and the primary services. Procedures performed by the MPS were more likely to be successfully completed (95.8 % vs. 92.8 %, p = 0.02) and to use best practice safety process measures, including use of ultrasound guidance when appropriate (96.8 % vs. 90.0 %, p = 0.0004), avoidance of femoral venous catheterization (89.5 vs. 82.7 %, p = 0.02) and involvement of attending physicians (99.3 % vs. 57.0 %, p < 0.0001). Although use of a MPS did not significantly affect the rate of major complications or resident opportunities for training in bedside procedures, it was associated with increased use of best practice safety process measures.

  6. Load research manual. Volume 2. Fundamentals of implementing load research procedures

    Energy Technology Data Exchange (ETDEWEB)

    Brandenburg, L.; Clarkson, G.; Grund, Jr., C.; Leo, J.; Asbury, J.; Brandon-Brown, F.; Derderian, H.; Mueller, R.; Swaroop, R.

    1980-11-01

    This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. In Volumes 1 and 2, procedures are suggested for determining data requirements for load research, establishing the size and customer composition of a load survey sample, selecting and using equipment to record customer electricity usage, processing data tapes from the recording equipment, and analyzing the data. Statistical techniques used in customer sampling are discussed in detail. The costs of load research also are estimated, and ongoing load research programs at three utilities are described. The manual includes guides to load research literature and glossaries of load research and statistical terms.

  7. Manual ward reduction of gastroschisis without anesthesia, a safe procedure – 8 years experience

    Directory of Open Access Journals (Sweden)

    Kamal Nain Rattan

    2017-01-01

    Full Text Available Introduction: Gastroschisis is the most common type of abdominal wall defect at birth. Various modalities of treatment have been proposed ranging from primary closure to the staged closure using prosthetic materials under general anesthesia. One of the modalities is manual ward reduction with primary repair of gastroschisis without anesthesia. We are reporting our 8 years of experience with manual ward reduction of gastroschisis with primary repair without anesthesia.Materials and methods: It is a retrospective analysis of all patients of gastroschisis who presented in our institution from January 2008 to June 2016. The data were analyzed for antenatal diagnosis, sex, day of presentation, weight of baby, associated anomalies, management by manual reduction without anesthesia and post reduction morbidity and mortality.Results: Out of a total of 68 patients, 28 were females and 40 were males. Fifty-five cases (80.8% were antenatally diagnosed. Fifty-nine patients (86.7% presented within 24 hours of birth while the rest had delayed presentation. Preterms (< 37 weeks were 18 (26.4%. Cases of simple gastroschisis were 22 while those complicated were 46. The average birth weight was 1.88 kg with the lowest weight of 1 kg who was a 27-week preterm. In 60 patients (88.2%, bedside manual reduction without anesthesia and primary closure was possible while in 8 patients it could not be done owing to delayed presentation and complications. The mortality in these patients was 40%.Conclusion: Manual reduction and primary closure of gastroschisis without anesthesia is a safe procedure. It requires no ventilator support and can be managed with antibiotics, total parenteral nutrition (TPN and continuous positive airway pressure (CPAP in the post-reduction period.

  8. Manual of extravascular minimally invasive interventional procedures of the liver and biliary tract

    International Nuclear Information System (INIS)

    Miranda Mena, Shirley

    2011-01-01

    The use of interventional radiology and image-guided surgery has increased. Interventional radiologists are involved in patient treatment, well as in the diagnosis of the disease carrying his knowledge to the tumor treatment and procedures more invasive. Large amount of didactic material there are available, but the country lacks a manual to standardize interventional radiological techniques carried out. Also, those that could be instituted and adapted effectively in the management of hepatobiliary pathology of the Sistema de Salud Publica in Costa Rica, that covers the main procedures and adopt guidelines in a standardized way. A manual of procedures minimally invasive radiologic extravascular of the liver and biliary tract, is presented with broad bibliographic support that directs, standardizes and is adaptable to the needs and own resources of Costa Rica. Interventional radiology has been a non surgical alternative of a low index of complications, useful for the management of some health problems, avoids surgery and certainly lower costs. An alternative to surgical treatment of many conditions is offered, thereby reducing complications (morbidity) and can eliminate the need for hospitalization, in some cases. The development of new materials has allowed the most common working tools of the medical field are improved and become increasingly more efficient in the diagnosis and treatment of diseases, improving the training of radiologists in the interventional field. (author) [es

  9. A Procedure for Structural Weight Estimation of Single Stage to Orbit Launch Vehicles (Interim User's Manual)

    Science.gov (United States)

    Martinovic, Zoran N.; Cerro, Jeffrey A.

    2002-01-01

    This is an interim user's manual for current procedures used in the Vehicle Analysis Branch at NASA Langley Research Center, Hampton, Virginia, for launch vehicle structural subsystem weight estimation based on finite element modeling and structural analysis. The process is intended to complement traditional methods of conceptual and early preliminary structural design such as the application of empirical weight estimation or application of classical engineering design equations and criteria on one dimensional "line" models. Functions of two commercially available software codes are coupled together. Vehicle modeling and analysis are done using SDRC/I-DEAS, and structural sizing is performed with the Collier Research Corp. HyperSizer program.

  10. Development of manual procedures for care of pregnant patients in radiotherapy service; Desarrollo de manual de procedimentos para atencion de pacientes embarazadas en servicio de radioterapia

    Energy Technology Data Exchange (ETDEWEB)

    Scarabino, M.L., E-mail: maliscarabino@gmail.com [Hospital Italiano de Buenos Aires (HIBA), Buenos Aires (Argentina); Ruggeri, R.M.; Colombo, S.; Mairal, L.; Sardi, M.E., E-mail: ricardoruggeri@gmail.com [Mevaterapia Centro Medico, Buenos Aires (Argentina)

    2013-11-01

    The work involves the creation of a manual of procedures for the care of pregnant patients in a radiotherapy center in which each instance of treatment is included, from the obstetrician-oncology comprehensive assessment during admission to establishing controls newborn and its subsequent development in multidisciplinary team. For the preparation of the manual had to design an anthropomorphic phantom that resembles a pregnant woman, which was used to carry out internal and external dosimetry. In turn imparted calculations fetal doses using TPS, imaging tests with MRI, avoiding the use of the tomograph and adapted to the resonator involved were carried immobilizer. All experiences and progress made during the treated cases are introduced in the procedures manual, making it a dynamic tool for continuous improvement for the institution.

  11. 49 CFR 195.402 - Procedural manual for operations, maintenance, and emergencies.

    Science.gov (United States)

    2010-10-01

    ... operating conditions by monitoring pressure, temperature, flow or other appropriate operational data and...) Minimization of public exposure to injury and probability of accidental ignition by assisting with evacuation... SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Operation and Maintenance § 195.402 Procedural...

  12. Convention on nuclear safety. Rules of procedure and financial rules

    International Nuclear Information System (INIS)

    1999-01-01

    The document is the first revision of the Rules of Procedures and Financial Rules that apply mutatis mutandis to any meetings of the Contracting Parties to the Convention on Nuclear Safety (INFCIRC/573), convened in accordance with the Chapter 3 of the Convention

  13. Safety and efficacy of procedural sedation and analgesia (PSA ...

    African Journals Online (AJOL)

    Safety and efficacy of procedural sedation and analgesia (PSA) conducted by medical officers in a level 1 hospital in Cape Town. ... Respiratory complications were treated with simple airway manoeuvres; no patient required intubation or experienced respiratory problems after waking up. There was no significant difference ...

  14. Uncodified safety norms and procedural compliance in nuclear power plants

    International Nuclear Information System (INIS)

    Ignatov, M.

    2000-01-01

    The mechanism of procedural compliance in operational teams is analysed. It is investigated the interrelationship between codified (institutional or officials) rules and uncodified safety norm and their influence on the job performance, social behaviour and social interaction of the operational personnel

  15. Convention on nuclear safety. Rules of procedure and financial rules

    International Nuclear Information System (INIS)

    1998-01-01

    The document presents the Rules of Procedure and Financial Rules that apply mutatis mutandis to any meeting of the Contracting Parties to the Convention on Nuclear Safety (INFCIRC/449) convened in accordance with Chapter 3 of the Convention. It includes four parts: General provisions, Preparatory process for review meetings, Review meetings, and Amendment and interpretation of rules

  16. Convention on Nuclear Safety. Rules of procedure and financial rules

    International Nuclear Information System (INIS)

    2002-01-01

    The document is the second revision of the Rules of Procedures and Financial Rules that apply mutatis mutandis to any meetings of the Contracting Parties to the Convention on Nuclear Safety (INFCIRC/573), convened in accordance with the Chapter 3 of the Convention

  17. Manual on radiological safety in uranium and thorium mines and mills

    International Nuclear Information System (INIS)

    1976-01-01

    The manual describes the personnel radiation hazards in uranium and thorium mines and mills. Measures which should be taken in order to protect the workers are outlined. The problems of air born radioactivity, external radiation, surface contamination and radioactive waste are treated. Safety standards in relation to the above mentioned subjects are given. An outline is given for monitoring programme. Monitoring methods, control methods and means of medical control are given

  18. Splash Safety During Dermatologic Procedures Among US Dermatology Residents.

    Science.gov (United States)

    Korta, Dorota Z; Chapman, Lance W; Lee, Patrick K; Linden, Kenneth G

    2017-07-01

    Dermatologists are at potential risk of acquiring infections from contamination of the mucous membranes by blood and body fluids. However, there are little data on splash safety during procedural dermatology. To determine dermatology resident perceptions about splash risk during dermatologic procedures and to quantify the rate of protective equipment use. An anonymous on-line survey was sent to 108 United States ACGME-approved dermatology residency programs assessing frequency of facial protection during dermatologic procedures, personal history of splash injury, and, if applicable, reasons for not always wearing facial protection. A total of 153 dermatology residents responded. Rates of facial protection varied by procedure, with the highest rates during surgery and the lowest during local anesthetic injection. Over 54% of respondents reported suffering facial splash while not wearing facial protection during a procedure. In contrast, 88.9% of respondents correctly answered that there is a small risk of acquiring infection from mucosal splash. Residency program recommendations for facial protection seem to vary by procedure. The authors' results demonstrate that although facial splash is a common injury, facial protection rates and protective recommendations vary significantly by procedure. These data support the recommendation for enhanced facial protection guidelines during procedural dermatology.

  19. Radiation safety procedures in radioiodine therapy for thyroid cancer

    International Nuclear Information System (INIS)

    Rajashekharrao, B.; Samuel, A.M.

    1999-01-01

    During any administration of radioactive materials, it is imperative to always be conversant with any forbidden radiation health safety practices. This need is amplified when dealing with therapeutic amount of radionuclides. Among all the procedures dealing with the use of radiopharmaceuticals, it is easiest to think of 131 I, since this is the most widely used unsealed source of a radiopharmaceutical for treatment of thyroid cancer and hyperthyroidism and carries with it most of the problems associated with therapy applications

  20. Licensing procedures and safety criteria for core conversion in Japan

    International Nuclear Information System (INIS)

    Kanda, K.; Nakagome, Y.; Hayashi, M.

    1983-01-01

    Procedures relating to the construction and operation of reactor facilities are discussed. Specifically, the Safety Analysis Report on the Kyoto University Critical Assembly (KUCA) core conversion (93% to 45% enrichment) is noted. The results of critical experiments in the KUCA and of burnup tests in the Oak Ridge Research (ORR) Reactor will be used in the final determination of the feasibility of the conversion of the Kyoto University High Flux Reactor (KUHFR) to the use of 45% enrichment

  1. A procedure for safety assessment of components with cracks - Handbook

    International Nuclear Information System (INIS)

    Andersson, P.; Bergman, M.; Brickstad, B.; Dahlberg, L.; Nilsson, F.; Sattari-Far, I.

    1996-01-01

    In this handbook a procedure is described which can be used both for assessment of detected cracks or crack like defects or for defect tolerance analysis. The procedure can be used to calculate possible crack growth due to fatigue or stress corrosion and to calculate the reserve margin for failure due to fracture and plastic collapse. For ductile materials, the procedure gives the reserve margin for initiation of stable crack growth. Thus, an extra reserve margin, unknown to size, exists for failure in components made of ductile materials. The procedure was developed for operative use with the following objectives in mind: The procedure should be able to handle both linear and non-linear problems without any a priori division; The procedure shall ensure uniqueness of the safety assessment; The procedure should be well defined and easy to use; The conservatism of the procedure should be well validated; The handbook that documents the procedure should be so complete that for most assessments access to any other fracture mechanics literature should not be necessary. The method utilized is based on the R6-method developed at Nuclear Electric plc. This method can in principle be used for all metallic materials. It is, however, more extensively verified for steel alloys only. The method is not intended for use in temperatures where creep deformation is of importance. The first edition of the handbook was released in 1990 and the second in 1991. This third edition has been extensively revised. A Windows-based program (SACC) has been developed which can perform the assessments described in the book including calculation of crack growth due to stress corrosion and fatigue. 52 refs., 27 figs., 35 tabs

  2. The human touch: skin temperature during the rubber hand illusion in manual and automated stroking procedures.

    Directory of Open Access Journals (Sweden)

    Marieke Rohde

    Full Text Available A difference in skin temperature between the hands has been identified as a physiological correlate of the rubber hand illusion (RHI. The RHI is an illusion of body ownership, where participants perceive body ownership over a rubber hand if they see it being stroked in synchrony with their own occluded hand. The current study set out to replicate this result, i.e., psychologically induced cooling of the stimulated hand using an automated stroking paradigm, where stimulation was delivered by a robot arm (PHANToM(TM force-feedback device. After we found no evidence for hand cooling in two experiments using this automated procedure, we reverted to a manual stroking paradigm, which is closer to the one employed in the study that first produced this effect. With this procedure, we observed a relative cooling of the stimulated hand in both the experimental and the control condition. The subjective experience of ownership, as rated by the participants, by contrast, was strictly linked to synchronous stroking in all three experiments. This implies that hand-cooling is not a strict correlate of the subjective feeling of hand ownership in the RHI. Factors associated with the differences between the two designs (differences in pressure of tactile stimulation, presence of another person that were thus far considered irrelevant to the RHI appear to play a role in bringing about this temperature effect.

  3. Dysfunctional Workers, Functional Texts: The Transformation of Work in Institutional Procedure Manuals.

    Science.gov (United States)

    Sullivan, Francis J.

    1997-01-01

    Examines how conflicts between management and workers over division of labor are enacted in two manuals--the official manual operationalizing Internal Revenue Service (IRS) regulations and a "translation" of the official manual--governing tax examiners' work in an IRS Service Center. Finds that systemic differences between the manuals…

  4. Quality and safety of nuclear installations: the role of administration, and, nuclear safety and regulatory procedures

    International Nuclear Information System (INIS)

    Queniart, D.

    1979-12-01

    In the first paper the author defines the concepts of safety and quality and describes the means of intervention by the Public Authorities in safety matters of nuclear installations. These include individual authorisations, definition and application of technical rules and surveillance of installations. In the second paper he defines the distinction between radiation protection and safety and presents the legislative and regulatory plan for nuclear safety in France. A central safety service for nuclear installations was created in March 1973 within the Ministry of Industrial and Scientific Development, where, amongst other tasks, it draws up regulatory procedures and organizes inspections of the installations. The main American regulations for light water reactors are outlined and the French regulatory system for different types of reactors discussed

  5. Manual gas tungsten arc (dc) and semiautomatic gas metal arc welding of 6XXX aluminum. Welding procedure specification

    International Nuclear Information System (INIS)

    Wodtke, C.H.; Frizzell, D.R.; Plunkett, W.A.

    1985-08-01

    Procedure WPS-1009 is qualified under Section IX of the ASME Boiler and Pressure Vessel Code for manual gas tungsten arc (DC) and semiautomatic gas metal arc (DC) welding of aluminum alloys 6061 and 6063 (P-23), in thickness range 0.187 to 2 in.; filler metal is ER4043 (F-23); shielding gases are helium (GTAW) and argon (GMAW)

  6. Efficacy, safety, and patient acceptability of the Essure™ procedure

    Directory of Open Access Journals (Sweden)

    Hopkins MR

    2011-04-01

    Full Text Available Collette R Lessard, Matthew R HopkinsDepartment of Obstetrics and Gynecology, Mayo Clinic, Rochester, Minnesota, USAAbstract: The Essure™ system for permanent contraception was developed as a less invasive method of female sterilization. Placement of the Essure™ coil involves a hysteroscopic transcervical technique. This procedure can be done in a variety of settings and with a range of anesthetic options. More than eight years have passed since the US Food and Drug Administration approval of Essure™. Much research has been done to evaluate placement success, adverse outcomes, satisfaction, pain, and the contraceptive efficacy of the Essure™. The purpose of this review is to summarize the available literature regarding the efficacy, safety, and patient satisfaction with this new sterilization technique.Keywords: hysteroscopic sterilization, Essure™, safety, efficacy, acceptability

  7. Recommendations to improve radiation safety during invasive cardiovascular procedures

    International Nuclear Information System (INIS)

    Miranda, Patricia; Ubeda, Carlos; Vano, Eliseo; Nocetti, Diego

    2014-01-01

    In this paper we present guidelines aimed to improve radiation safety during invasive cardiovascular procedures. Unwanted effects upon patients and medical personnel are conventionally classified. A program of Quality Assurance is proposed, an aspect of which is a program for radiologic protection, including operator protection, radiation monitoring, shielding and personnel training. Permanent and specific actions should be taken at every cardiovascular lab, before, during and after interventions. In order to implement these guidelines and actions, a fundamental step is a review of current legislation. Specific programs for quality control and radiologic protection along with a definition of acceptable radiation exposure doses are required

  8. Manual on safety aspects of the design and equipment of hot laboratories. 1981 ed

    International Nuclear Information System (INIS)

    1981-01-01

    This manual covers the general principles of planning and design of areas inside laboratories according to the varying potential radiation and contamination hazards; enclosures for radioactive material containment; viewing and lighting systems and various types of manipulators; transfer and transport of radioactive materials within the laboratories; air cleaning and ventilation systems, with particular reference to IAEA Safety Series No.17; techniques for controlling air pollution from the operation of nuclear facilities; various radioactive waste disposal systems; criticality control; fire protection; personnel monitoring, including changing-room monitoring and protective clothing; standardization and automation; and administrative controls. Although alpha, beta, gamma technologies have developed separately, equipment used in radioactive work is common to many operations. There is a step change in technology between work with uranium and plutonium and between work with plutonium and other transuranics; with plutonium one enters the field of alpha, beta, gamma technology. This manual reports the basic requirements and gives reference to more sophisticated techniques available. It is not concerned with work on a commercial scale. Other publications of interest in this context, for instance IAEA Safety Series No.39, are referenced for more detailed information.

  9. PC based manual and safety logic card test setup for 235 MWe PHWRs

    International Nuclear Information System (INIS)

    Chandgadkar, G.M.; Kohli, A.K.; Agarwal, R.G.; Chandra, Rajesh

    1992-01-01

    Fuel handling controls for 235 MWe PHWR make use of Manual and Logic cards (MLCs) for providing safety interlocks. These cards consist of various type of logic blocks. By connecting these logic blocks all the safety interlocks required for fuel handling controls have been provided. Previously trouble shooting of these cards was done by means of logic probe. Since the method was manual, it was laborious and time consuming. PC based test setup has overcome this drawback and detects the fault at the component level within few seconds. It also gives printout of status of faulty MLC cards. Here motherboard has been designed having slots for insertion of MLC cards. The input/output connection of these cards are coming to two 50 pin FRC connectors. PC communicates through 144 line digital input/output card with MLC card under test. Software is user friendly and outputs suitable input patterns to the card under test and checks for output pattern. It compares this output pattern with compare pattern and detects the fault and displays the symptoms. This system is currently in use at test facility for fuelling machine for 235 MWe PHWR reactor at Refuelling Technology Division, Hall-7. This test setup has been proposed for use at NAPP and future reactors. (author). 4 figs., 1 annexure

  10. Licensing procedures and safety criteria for core conversion in Japan

    International Nuclear Information System (INIS)

    Kanda, K.; Nakagome, Y.; Hayashi, M.

    1983-01-01

    In Japan, the establishment and operation of nuclear installations are governed mainly by the Law for Regulation of Nuclear Source Material, Nuclear Fuel Material and Reactors. This law lays down the regulations and conditions for licensing of the various installations involved in the nuclear fuel cycle, namely licensing of installations for refining, fabricating and reprocessing; and reactors, as well as licensing of the use of nuclear fuels in research facilities. Although procedures for the installations listed above vary depending on the installation concerned, only those relating to construction and operation of reactor facilities will be analysed in this study, as the conditions and principles applying to licensing and control of other installations are, to a large extent, similar to those concerning reactor facilities. The second part of this presentation describes the safety review of the KUCA reactor core conversion form HEU to MEU. For the safety review of the core conversion, the Committee on Examination of Reactor Safety of Japanese Government examined mainly the the nuclear characteristics and the integrity of aluminide fuel plates, which was very severe because we had no experience to use aluminide fuel plates in Japan. The integrity of fuel plates and the results of the worst accident analysis for the MEU core are shown with the comparison between the HEU and MEU cores. The significant difference was not observed between them. All the regulatory procedures were completed in September 1980. Fabrication of MEU fuel elements for the KUCA experiments by CERCA in France was started in September 1980, and will be completed in March 1981. The critical experiments in the KUCA with MEU fuel will be started on a single-core in May 1981 as a first step. Those on a coupled-core will follow

  11. Relating safety, productivity and company type for motor-manual logging operations in the Italian Alps.

    Science.gov (United States)

    Montorselli, Niccolò Brachetti; Lombardini, Carolina; Magagnotti, Natascia; Marchi, Enrico; Neri, Francesco; Picchi, Gianni; Spinelli, Raffaele

    2010-11-01

    The study compared the performance of four different logging crews with respect to productivity, organization and safety. To this purpose, the authors developed a data collection method capable of providing a quantitative analysis of risk-taking behavior. Four crews were tested under the same working conditions, representative of close-to-nature alpine forestry. Motor-manual working methods were applied, since these methods are still prevalent in the specific study area, despite the growing popularity of mechanical processors. Crews from public companies showed a significantly lower frequency of risk-taking behavior. The best safety performance was offered by the only (public) crew that had been administered formal safety training. The study seems to deny the common prejudice that safety practice is inversely proportional to productivity. Instead, productivity is increased by introducing more efficient working methods and equipment. The quantitative analysis of risk-taking behavior developed in this study can be applied to a number of industrial fields besides forestry. Characterizing risk-taking behavior for a given case may eventually lead to the development of custom-made training programmes, which may address problem areas while avoiding that the message is weakened by the inclusion of redundant information. In the specific case of logging crews in the central Alps, the study suggests that current training courses may be weak on ergonomics, and advocates a staged training programme, focusing first on accident reduction and then expanding to the prevention of chronic illness. 2010 Elsevier Ltd. All rights reserved.

  12. Cost-benefit analysis model: A tool for area-wide fruit fly management. Procedures manual

    International Nuclear Information System (INIS)

    Enkerlin, W.; Mumford, J.; Leach, A.

    2007-03-01

    The Generic Fruit Fly Cost-Benefit Analysis Model assists in economic decision making associated with area-wide fruit fly control options. The FRUIT FLY COST-BENEFIT ANALYSIS PROGRAM (available on 1 CD-ROM from the Joint FAO/IAEA Programme of Nuclear Techniques in Food and Agriculture) is an Excel 2000 Windows based program, for which all standard Windows and Excel conventions apply. The Model is user friendly and thus largely self-explanatory. Nevertheless, it includes a procedures manual that has been prepared to guide the user, and thus should be used together with the software. Please note that the table presenting the pest management options in the Introductory Page of the model is controlled by spin buttons and click boxes. These controls are linked to macros that hide non relevant tables and boxes. N.B. it is important that the medium level of security is selected from the Tools menu of Excel, to do this go to Tools|Macros|Security| and select Medium. When the file is opened a form will appear containing three buttons, click on the middle button, 'Enable Macros', so that the macros may be used. Ideally the model should be used as a support tool by working groups aiming at assessing the economic returns of different fruit fly control options (suppression, eradication, containment and prevention). The working group should include professionals in agriculture with experience in area-wide implementation of integrated pest management programmes, an economist or at least someone with basic knowledge in economics, and if relevant, an entomologist with some background in the application of the sterile insect technique (SIT)

  13. MORT User's Manual for use with the Management Oversight and Risk Tree analytical logic diagram. [Contains a list of System Safety Development Center publications

    Energy Technology Data Exchange (ETDEWEB)

    Knox, N.W.; Eicher, R.W.

    1992-02-01

    This report contains the User's Manual for MORT (Management Oversight and Risk Tree), a logic diagram in the form of a work sheet'' that illustrates a long series of interrelated questions. MORT is a comprehensive analytical procedure that provides a disciplined method for determining the causes and contributing factors of major accidents. Alternatively, it serves as a tool to evaluate the quality of an existing system. While similar in many respects to fault tree analysis, MORT is more generalized and presents over 1,500 specific elements of an ideal universal'' management program for optimizing environment, safety and health, and other programs. This User's Manual is intended to be used with the MORT diagram dated February 1992.

  14. Efficacy and Safety of Manual Partial Red Cell Exchange in the Management of Severe Complications of Sickle Cell Disease in a Developing Country

    Directory of Open Access Journals (Sweden)

    B. F. Faye

    2017-01-01

    Full Text Available Introduction. The realization of red cell exchange (RCE in Africa faces the lack of blood, transfusion safety, and equipment. We evaluated its efficacy and safety in severe complications of sickle cell disease. Patients and Method. Manual partial RCE was performed among sickle cell patients who had severe complications. Efficacy was evaluated by clinical evolution, blood count, and electrophoresis of hemoglobin. Safety was evaluated on adverse effects, infections, and alloimmunization. Results. We performed 166 partial RCE among 44 patients including 41 homozygous (SS and 2 heterozygous composites SC and 1 S/β0-thalassemia. The mean age was 27.9 years. The sex ratio was 1.58. The regression of symptoms was complete in 100% of persistent vasoocclusive crisis and acute chest syndrome, 56.7% of intermittent priapism, and 30% of stroke. It was partial in 100% of leg ulcers and null in acute priapism. The mean variations of hemoglobin and hematocrit rate after one procedure were, respectively, +1.4 g/dL and +4.4%. That of hemoglobin S after 2 consecutive RCE was −60%. Neither alloimmunization nor viral seroconversion was observed. Conclusion. This work shows the feasibility of manual partial RCE in a low-resource setting and its efficacy and safety during complications of SCD outside of acute priapism.

  15. Efficacy and Safety of Manual Partial Red Cell Exchange in the Management of Severe Complications of Sickle Cell Disease in a Developing Country

    Science.gov (United States)

    Sow, D.; Seck, M.; Dieng, N.; Toure, S. A.; Gadji, M.; Senghor, A. B.; Gueye, Y. B.; Sy, D.; Sall, A.; Dieye, T. N.; Toure, A. O.; Diop, S.

    2017-01-01

    Introduction The realization of red cell exchange (RCE) in Africa faces the lack of blood, transfusion safety, and equipment. We evaluated its efficacy and safety in severe complications of sickle cell disease. Patients and Method Manual partial RCE was performed among sickle cell patients who had severe complications. Efficacy was evaluated by clinical evolution, blood count, and electrophoresis of hemoglobin. Safety was evaluated on adverse effects, infections, and alloimmunization. Results We performed 166 partial RCE among 44 patients including 41 homozygous (SS) and 2 heterozygous composites SC and 1 S/β0-thalassemia. The mean age was 27.9 years. The sex ratio was 1.58. The regression of symptoms was complete in 100% of persistent vasoocclusive crisis and acute chest syndrome, 56.7% of intermittent priapism, and 30% of stroke. It was partial in 100% of leg ulcers and null in acute priapism. The mean variations of hemoglobin and hematocrit rate after one procedure were, respectively, +1.4 g/dL and +4.4%. That of hemoglobin S after 2 consecutive RCE was −60%. Neither alloimmunization nor viral seroconversion was observed. Conclusion This work shows the feasibility of manual partial RCE in a low-resource setting and its efficacy and safety during complications of SCD outside of acute priapism. PMID:28584527

  16. Approaches to document the efficacy and safety of microdermabrasion procedure.

    Science.gov (United States)

    Spencer, James M; Kurtz, Ellen S

    2006-11-01

    Microdermabrasion is a popular cosmetic procedure for skin rejuvenation, which is achieved by mechanical abrasion of the skin at a superficial level. The objective was to study the efficacy of microdermabrasion in photoaging and to investigate the compatibility of a cleanser and a lotion with microdermabrasion. Sixteen women underwent microdermabrasion to the face once a week for a total of six treatments. Subjects were also given a personal skin care regimen (cleanser and lotion). Colorimetry values as well as investigator and patients ratings for safety and efficacy were analyzed at various time points and compared to baseline. There were no significant changes in safety and tolerance variables throughout the study. Clinical efficacy variables (fine wrinkles, dullness, pigmentation, and large pores) significantly improved by the third treatment, with further improvement by the end of the study (six treatments). Subjects perceived improvement in facial photoaging variables. Colorimetry showed increased brightness and decreased yellowness of target skin sites on the face throughout the study. Multiple microdermabrasions were effective in significantly improving various facial photoaging variables. The personal skin care regimen used was well tolerated by the subjects.

  17. Program desk manual for occupational safety and health -- U.S. Department of Energy Richland Operations, Office of Environment Safety and Health

    International Nuclear Information System (INIS)

    Musen, L.G.

    1998-01-01

    The format of this manual is designed to make this valuable information easily accessible to the user as well as enjoyable to read. Each chapter contains common information such as Purpose, Scope, Policy and References, as well as information unique to the topic at hand. This manual can also be provided on a CD or Hanford Internet. Major topics include: Organization and program for operational safety; Occupational medicine; Construction and demolition; Material handling and storage; Hoisting and rigging; Explosives; Chemical hazards; Gas cylinders; Electrical; Boiler and pressure vessels; Industrial fire protection; Industrial hygiene; and Safety inspection checklist

  18. Program desk manual for occupational safety and health -- U.S. Department of Energy Richland Operations, Office of Environment Safety and Health

    Energy Technology Data Exchange (ETDEWEB)

    Musen, L.G.

    1998-08-27

    The format of this manual is designed to make this valuable information easily accessible to the user as well as enjoyable to read. Each chapter contains common information such as Purpose, Scope, Policy and References, as well as information unique to the topic at hand. This manual can also be provided on a CD or Hanford Internet. Major topics include: Organization and program for operational safety; Occupational medicine; Construction and demolition; Material handling and storage; Hoisting and rigging; Explosives; Chemical hazards; Gas cylinders; Electrical; Boiler and pressure vessels; Industrial fire protection; Industrial hygiene; and Safety inspection checklist.

  19. PGSFR Core Thermal Design Procedure to Evaluate the Safety Margin

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Sun Rock; Kim, Sang-Ji [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    The Korea Atomic Energy Research Institute (KAERI) has performed a SFR design with the final goal of constructing a prototype plant by 2028. The main objective of the SFR prototype plant is to verify the TRU metal fuel performance, reactor operation, and transmutation ability of high-level wastes. The core thermal design is to ensure the safe fuel performance during the whole plant operation. Compared to the critical heat flux in typical light water reactors, nuclear fuel damage in SFR subassemblies arises from a creep induced failure. The creep limit is evaluated based on the maximum cladding temperature, power, neutron flux, and uncertainties in the design parameters, as shown in Fig. 1. In this work, the core thermal design procedures are compared to verify the present PGSFR methodology based on the nuclear plant design criteria/guidelines and previous SFR thermal design methods. The PGSFR core thermal design procedure is verified based on the nuclear plant design criteria/guidelines and previous methods in LWRs and SFRs. The present method aims to directly evaluate the fuel cladding failure and to assure more safety margin. The 2 uncertainty is similar to 95% one-side tolerance limit of 1.96 in LWRs. The HCFs, ITDP, and MCM reveal similar uncertainty propagation for cladding midwall temperature for typical SFR conditions. The present HCFs are mainly employed from the CRBR except the fuel-related uncertainty such as an incorrect fuel distribution. Preliminary PGSFR specific HCFs will be developed by the end of 2015.

  20. 23 CFR 630.1106 - Policy and procedures for work zone safety management.

    Science.gov (United States)

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Policy and procedures for work zone safety management... Policy and procedures for work zone safety management. (a) Each agency's policy and processes, procedures, and/or guidance for the systematic consideration and management of work zone impacts, to be...

  1. Radiological Safety Analysis Computer (RSAC) Program Version 7.0 Users’ Manual

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Bradley J Schrader

    2009-03-01

    The Radiological Safety Analysis Computer (RSAC) Program Version 7.0 (RSAC-7) is the newest version of the RSAC legacy code. It calculates the consequences of a release of radionuclides to the atmosphere. A user can generate a fission product inventory from either reactor operating history or a nuclear criticality event. RSAC-7 models the effects of high-efficiency particulate air filters or other cleanup systems and calculates the decay and ingrowth during transport through processes, facilities, and the environment. Doses are calculated for inhalation, air immersion, ground surface, ingestion, and cloud gamma pathways. RSAC-7 can be used as a tool to evaluate accident conditions in emergency response scenarios, radiological sabotage events and to evaluate safety basis accident consequences. This users’ manual contains the mathematical models and operating instructions for RSAC-7. Instructions, screens, and examples are provided to guide the user through the functions provided by RSAC-7. This program was designed for users who are familiar with radiological dose assessment methods.

  2. Radiological Safety Analysis Computer (RSAC) Program Version 7.2 Users’ Manual

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Bradley J Schrader

    2010-10-01

    The Radiological Safety Analysis Computer (RSAC) Program Version 7.2 (RSAC-7) is the newest version of the RSAC legacy code. It calculates the consequences of a release of radionuclides to the atmosphere. A user can generate a fission product inventory from either reactor operating history or a nuclear criticality event. RSAC-7 models the effects of high-efficiency particulate air filters or other cleanup systems and calculates the decay and ingrowth during transport through processes, facilities, and the environment. Doses are calculated for inhalation, air immersion, ground surface, ingestion, and cloud gamma pathways. RSAC-7 can be used as a tool to evaluate accident conditions in emergency response scenarios, radiological sabotage events and to evaluate safety basis accident consequences. This users’ manual contains the mathematical models and operating instructions for RSAC-7. Instructions, screens, and examples are provided to guide the user through the functions provided by RSAC-7. This program was designed for users who are familiar with radiological dose assessment methods.

  3. Radiological Safety Analysis Computer (RSAC) Program Version 7.0 Users Manual

    International Nuclear Information System (INIS)

    Schrader, Bradley J.

    2009-01-01

    The Radiological Safety Analysis Computer (RSAC) Program Version 7.0 (RSAC-7) is the newest version of the RSAC legacy code. It calculates the consequences of a release of radionuclides to the atmosphere. A user can generate a fission product inventory from either reactor operating history or a nuclear criticality event. RSAC-7 models the effects of high-efficiency particulate air filters or other cleanup systems and calculates the decay and ingrowth during transport through processes, facilities, and the environment. Doses are calculated for inhalation, air immersion, ground surface, ingestion, and cloud gamma pathways. RSAC-7 can be used as a tool to evaluate accident conditions in emergency response scenarios, radiological sabotage events and to evaluate safety basis accident consequences. This users manual contains the mathematical models and operating instructions for RSAC-7. Instructions, screens, and examples are provided to guide the user through the functions provided by RSAC-7. This program was designed for users who are familiar with radiological dose assessment methods

  4. Procedures For Microbial-Ecology Laboratory

    Science.gov (United States)

    Huff, Timothy L.

    1993-01-01

    Microbial Ecology Laboratory Procedures Manual provides concise and well-defined instructions on routine technical procedures to be followed in microbiological laboratory to ensure safety, analytical control, and validity of results.

  5. 49 CFR 192.605 - Procedural manual for operations, maintenance, and emergencies.

    Science.gov (United States)

    2010-10-01

    ... operation of pressure-limiting and control devices. (6) Maintaining compressor stations, including... operations of a pipeline system commence. Appropriate parts of the manual must be kept at locations where..., operating and shutting down gas compressor units. (8) Periodically reviewing the work done by operator...

  6. Water Quality & Pollutant Source Monitoring: Field and Laboratory Procedures. Training Manual.

    Science.gov (United States)

    Office of Water Program Operations (EPA), Cincinnati, OH. National Training and Operational Technology Center.

    This training manual presents material on techniques and instrumentation used to develop data in field monitoring programs and related laboratory operations concerned with water quality and pollution monitoring. Topics include: collection and handling of samples; bacteriological, biological, and chemical field and laboratory methods; field…

  7. Procedure manual for the estimation of average indoor radon-daughter concentrations using the filtered alpha-track method

    International Nuclear Information System (INIS)

    George, J.L.

    1988-04-01

    One of the measurement needs of US Department of Energy (DOE) remedial action programs is the estimation of the annual-average indoor radon-daughter concentration (RDC) in structures. The filtered alpha-track method, using a 1-year exposure period, can be used to accomplish RDC estimations for the DOE remedial action programs. This manual describes the procedure used to obtain filtered alpha-track measurements to derive average RDC estimates from the measurrements. Appropriate quality-assurance and quality-control programs are also presented. The ''prompt'' alpha-track method of exposing monitors for 2 to 6 months during specific periods of the year is also briefly discussed in this manual. However, the prompt alpha-track method has been validated only for use in the Mesa County, Colorado, area. 3 refs., 3 figs

  8. Powered bone marrow biopsy procedures produce larger core specimens, with less pain, in less time than with standard manual devices

    Directory of Open Access Journals (Sweden)

    Larry J. Miller

    2011-07-01

    Full Text Available Bone marrow sampling remains essential in the evaluation of hematopoietic and many non-hematopoietic disorders. One common limitation to these procedures is the discomfort experienced by patients. To address whether a Powered biopsy system could reduce discomfort while providing equivalent or better results, we performed a randomized trial in adult volunteers. Twenty-six subjects underwent bilateral biopsies with each device. Core samples were obtained in 66.7% of Manual insertions; 100% of Powered insertions (P=0.002. Initial mean biopsy core lengths were 11.1±4.5 mm for the Manual device; 17.0±6.8 mm for the Powered device (P<0.005. Pathology assessment for the Manual device showed a mean length of 6.1±5.6 mm, width of 1.0±0.7 mm, and volume of 11.0±10.8 mm3. Powered device measurements were mean length of 15.3±6.1 mm, width of 2.0±0.3 mm, and volume of 49.1±21.5 mm3 (P<0.001. The mean time to core ejection was 86 seconds for Manual device; 47 seconds for the Powered device (P<0.001. The mean second look overall pain score was 33.3 for the Manual device; 20.9 for the Powered (P=0.039. We conclude that the Powered biopsy device produces superior sized specimens, with less overall pain, in less time.

  9. Characteristic values of the lumbar load of manual patient handling for the application in workers' compensation procedures

    Directory of Open Access Journals (Sweden)

    Wortmann Norbert

    2011-05-01

    Full Text Available Abstract Background The human spine is often exposed to mechanical load in vocational activities especially in combination with lifting, carrying and positioning of heavy objects. This also applies in particular to nursing activities with manual patient handling. In the present study a detailed investigation on the load of the lumbar spine during manual patient handling was performed. Methods For a total of 13 presumably endangering activities with transferring a patient, the body movements performed by healthcare workers were recorded and the exerted action forces were determined with regard to magnitude, direction and lateral distribution in the time course with a "measuring bed", a "measuring chair" and a "measuring floor". By the application of biomechanical model calculations the load on the lowest intervertebral disc of the lumbar spine (L5-S1 was determined considering the posture and action force data for every manual patient handling. Results The results of the investigations reveal the occurrence of high lumbar load during manual patient handling activities, especially in those cases, where awkward postures of the healthcare worker are combined with high action forces caused by the patient's mass. These findings were compared to suitable issues of corresponding investigations provided in the literature. Furthermore measurement-based characteristic values of lumbar load were derived for the use in statement procedures concerning the disease no. 2108 of the German list of occupational diseases. Conclusions To protect healthcare workers from mechanical overload and the risk of developing a disc-related disease, prevention measures should be compiled. Such measures could include the application of "back-fairer" nursing techniques and the use of "technical" and" small aids" to reduce the lumbar load during manual patient handling. Further studies, concerning these aspects, are necessary.

  10. Characteristic values of the lumbar load of manual patient handling for the application in workers' compensation procedures.

    Science.gov (United States)

    Jordan, Claus; Luttmann, Alwin; Theilmeier, Andreas; Kuhn, Stefan; Wortmann, Norbert; Jäger, Matthias

    2011-05-26

    The human spine is often exposed to mechanical load in vocational activities especially in combination with lifting, carrying and positioning of heavy objects. This also applies in particular to nursing activities with manual patient handling. In the present study a detailed investigation on the load of the lumbar spine during manual patient handling was performed. For a total of 13 presumably endangering activities with transferring a patient, the body movements performed by healthcare workers were recorded and the exerted action forces were determined with regard to magnitude, direction and lateral distribution in the time course with a "measuring bed", a "measuring chair" and a "measuring floor". By the application of biomechanical model calculations the load on the lowest intervertebral disc of the lumbar spine (L5-S1) was determined considering the posture and action force data for every manual patient handling. The results of the investigations reveal the occurrence of high lumbar load during manual patient handling activities, especially in those cases, where awkward postures of the healthcare worker are combined with high action forces caused by the patient's mass. These findings were compared to suitable issues of corresponding investigations provided in the literature. Furthermore measurement-based characteristic values of lumbar load were derived for the use in statement procedures concerning the disease no. 2108 of the German list of occupational diseases. To protect healthcare workers from mechanical overload and the risk of developing a disc-related disease, prevention measures should be compiled. Such measures could include the application of "back-fairer" nursing techniques and the use of "technical" and" small aids" to reduce the lumbar load during manual patient handling. Further studies, concerning these aspects, are necessary.

  11. Partial Red Blood Cell Exchange in Children and Young Patients with Sickle Cell Disease: Manual Versus Automated Procedure.

    Science.gov (United States)

    Escobar, Carlos; Moniz, Marta; Nunes, Pedro; Abadesso, Clara; Ferreira, Teresa; Barra, António; Lichtner, Anabela; Loureiro, Helena; Dias, Alexandra; Almeida, Helena

    2017-10-31

    The benefits of manual versus automated red blood cell exchange have rarely been documented and studies in young sickle cell disease patients are scarce. We aim to describe and compare our experience in these two procedures. Young patients (≤ 21 years old) who underwent manual- or automated-red blood cell exchange for prevention or treatment of sickle cell disease complications were included. Clinical, technical and hematological data were prospectively recorded and analyzed. Ninety-four red blood cell exchange sessions were performed over a period of 68 months, including 57 manual and 37 automated, 63 for chronic complications prevention, 30 for acute complications and one in the pre-operative setting. Mean decrease in sickle hemoglobin levels was higher in automated-red blood cell exchange (p exchange and access alarm on automated-red blood cell exchange. No major complication or alloimunization was recorded. Automated-red blood cell exchange decreased sickle hemoglobin levels more efficiently than manual procedure in the setting of acute and chronic complications of sickle cell disease, with minor technical concerns mainly due to vascular access. The threshold of sickle hemoglobin should be individualized for clinical and hematological goals. In our cohort of young patients, the need for an acceptable venous access was a limiting factor, but iron-overload was avoided. Automated red blood cell exchange is safe and well tolerated. It permits a higher sickle hemoglobin removal efficacy, better volume status control and iron-overload avoidance.

  12. Usefulness and Limitation of Manual Aspiration Immediately After Pneumothorax Complicating Interventional Radiological Procedures with the Transthoracic Approach

    International Nuclear Information System (INIS)

    Yamagami, Takuji; Kato, Takeharu; Hirota, Tatsuya; Yoshimatsu, Rika; Matsumoto, Tomohiro; Nishimura, Tsunehiko

    2006-01-01

    The goal of this study was to evaluate the efficacy of simple aspiration of air from the pleural space to prevent increased pneumothorax and avoid chest tube placement in cases of pneumothorax following interventional radiological procedures performed under computed tomography fluoroscopic guidance with the transthoracic percutaneous approach. While still on the scanner table, 102 cases underwent percutaneous manual aspiration of a moderate or large pneumothorax that had developed during mediastinal, lung, and transthoracic liver biopsies and ablations of lung and hepatic tumors (independent of symptoms). Air was aspirated from the pleural space by an 18- or 20-gauge intravenous catheter attached to a three-way stopcock and 20- or 50-mL syringe. We evaluated the management of each such case during and after manual aspiration. In 87 of the 102 patients (85.3%), the pneumothorax had resolved completely on follow-up chest radiographs without chest tube placement, but chest tube placement was required in 15 patients. Requirement of chest tube insertion significantly increased in parallel with the increased volume of aspirated air. When receiver-operating characteristic curves were applied retrospectively, the optimal cutoff level of aspirated air on which to base a decision to abandon manual aspiration alone and resort to chest tube placement was 670 mL. Percutaneous manual aspiration of the pneumothorax performed immediately after the procedure might prevent progressive pneumothorax and eliminate the need for chest tube placement. However, when the amount of aspirated air is large (such as more than 670 mL), chest tube placement should be considered

  13. Operating manual for the Bulk Shielding Reactor

    International Nuclear Information System (INIS)

    1983-04-01

    The BSR is a pool-type reactor. It has the capabilities of continuous operation at a power level of 2 MW or at any desired lower power level. This manual presents descriptive and operational information. The reactor and its auxillary facilities are described from physical and operational viewpoints. Detailed operating procedures are included which are applicable from source-level startup to full-power operation. Also included are procedures relative to the safety of personnel and equipment in the areas of experiments, radiation and contamination control, emergency actions, and general safety. This manual supercedes all previous operating manuals for the BSR

  14. Operating manual for the Bulk Shielding Reactor

    International Nuclear Information System (INIS)

    1987-03-01

    The BSR is a pool-type reactor. It has the capabilities of continuous operation at a power level of 2 MW or at any desired lower power level. This manual presents descriptive and operational information. The reactor and its auxiliary facilities are described from physical and operational viewpoints. Detailed operating procedures are included which are applicable from source-level startup to full-power operation. Also included are procedures relative to the safety of personnel and equipment in the areas of experiments, radiation and contamination control, emergency actions, and general safety. This manual supersedes all previous operating manuals for the BSR

  15. Operating manual for the Bulk Shielding Reactor

    Energy Technology Data Exchange (ETDEWEB)

    1987-03-01

    The BSR is a pool-type reactor. It has the capabilities of continuous operation at a power level of 2 MW or at any desired lower power level. This manual presents descriptive and operational information. The reactor and its auxiliary facilities are described from physical and operational viewpoints. Detailed operating procedures are included which are applicable from source-level startup to full-power operation. Also included are procedures relative to the safety of personnel and equipment in the areas of experiments, radiation and contamination control, emergency actions, and general safety. This manual supersedes all previous operating manuals for the BSR.

  16. Operating manual for the Bulk Shielding Reactor

    Energy Technology Data Exchange (ETDEWEB)

    1983-04-01

    The BSR is a pool-type reactor. It has the capabilities of continuous operation at a power level of 2 MW or at any desired lower power level. This manual presents descriptive and operational information. The reactor and its auxillary facilities are described from physical and operational viewpoints. Detailed operating procedures are included which are applicable from source-level startup to full-power operation. Also included are procedures relative to the safety of personnel and equipment in the areas of experiments, radiation and contamination control, emergency actions, and general safety. This manual supercedes all previous operating manuals for the BSR.

  17. Procedure manual for the estimation of average indoor radon-daughter concentrations using the radon grab-sampling method

    International Nuclear Information System (INIS)

    George, J.L.

    1986-04-01

    The US Department of Energy (DOE) Office of Remedial Action and Waste Technology established the Technical Measurements Center to provide standardization, calibration, comparability, verification of data, quality assurance, and cost-effectiveness for the measurement requirements of DOE remedial action programs. One of the remedial-action measurement needs is the estimation of average indoor radon-daughter concentration. One method for accomplishing such estimations in support of DOE remedial action programs is the radon grab-sampling method. This manual describes procedures for radon grab sampling, with the application specifically directed to the estimation of average indoor radon-daughter concentration (RDC) in highly ventilated structures. This particular application of the measurement method is for cases where RDC estimates derived from long-term integrated measurements under occupied conditions are below the standard and where the structure being evaluated is considered to be highly ventilated. The radon grab-sampling method requires that sampling be conducted under standard maximized conditions. Briefly, the procedure for radon grab sampling involves the following steps: selection of sampling and counting equipment; sample acquisition and processing, including data reduction; calibration of equipment, including provisions to correct for pressure effects when sampling at various elevations; and incorporation of quality-control and assurance measures. This manual describes each of the above steps in detail and presents an example of a step-by-step radon grab-sampling procedure using a scintillation cell

  18. Evaluation and assessment methodology, standards, and procedures manual of the United States Federal Radiological Monitoring and Assessment Center

    International Nuclear Information System (INIS)

    Kerns, K.C.; Burson, Z.G.; Smith, J.M.; Blanchard, R.L.

    2000-01-01

    In the event of a major radiological emergency, the U.S. Federal Radiological Emergency Response Plan authorises the creation of the Federal Radiological Monitoring and Assessment Center (FRMAC). The FRMAC is established to co-ordinate the Federal off-site monitoring and assessment activities, and is comprised of representatives from several Federal agencies and Department of Energy contractors who provide assistance to the state(s) and Lead Federal Agency. The Evaluation and Assessment (E and A) Division of the FRMAC is responsible for receiving, storing, and interpreting environmental surveillance data to estimate the potential health consequences to the population in the vicinity of the accident site. The E and A Division has commissioned the preparation of a methodology and procedures manual which will result in a consistent approach by Division members in carrying out their duties. The first edition of this manual is nearing completion. In this paper, a brief review of the structure of the FRMAC is presented, with emphasis on the E and A Division. The contents of the E and A manual are briefly described, as are future plans for its expansion. (author)

  19. Risk monitor - a tool for operational safety assessment risk monitor - user's manual

    International Nuclear Information System (INIS)

    Hari Prasad, M.; Vinod, Gopika; Saraf, R.K.; Ghosh, A.K.

    2006-06-01

    Probabilistic Safety Assessment has become a key tool as on today to identify and understand Nuclear Power Plant vulnerabilities. As a result of the availability of these PSA studies, there is a desire to use them to enhance plant safety and to operate the nuclear stations in the most efficient manner. Risk Monitor is a PC based tool, which computes the real time safety level and assists plant personnel to manage day-to-day activities. Risk Monitor is a PC based user friendly software tool used for modification and re-analysis of a nuclear Power plant. Operation of Risk Monitor is based on PSA methods for assisting in day to day applications. Risk Monitoring programs can assess the risk profile and are used to optimize the operation of Nuclear Power Plants with respect to a minimum risk level over the operating time. This report presents the background activities of Risk Monitor, its application areas and the step by step procedure for the user.to interact with the software. This software can be used with the PSA model of any Nuclear Power Plant. (author)

  20. Licensing procedures and safety criteria for research reactors in France

    International Nuclear Information System (INIS)

    Berry, J.L.; Lerouge, B.

    1980-11-01

    This paper summarizes the recent evolution of the French research reactor capacity, describes the licensing process, the main safety criteria which are taken into consideration, and associated safety research. Some of the existing facilities underwent important modifications to comply with more severe safety criteria, increase the experimental capabilities or qualify new low-enrichment fuels for research reactors. At the end, a few considerations are given to the consequences of the Osiris core conversion

  1. Manual on nuclear gauges. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1992-01-01

    In addition to a basic guide to the principles of production of ionizing radiation and to the methods of radiation protection and dosimetry, this booklet considers the procedures that should be employed when using nuclear gauges. Applications for such gauges are described and radiation protection procedures discussed

  2. Oak Ridge National Laboratory whole-body counter: internal operating procedure manual

    International Nuclear Information System (INIS)

    Berger, C.D.; Lane, B.H.

    1982-08-01

    The general purpose of the ORNL Whole Body Counter is to provide a rapid estimation of the type and quantity of radionuclide deposited in the human body. This report contains a review of the equipment in use at the facility and the procedure for its operation, the standard procedure for performing a routine whole body count, and a discussion of interpretation of results

  3. Abdominoplasty: Risk Factors, Complication Rates, and Safety of Combined Procedures.

    Science.gov (United States)

    Winocour, Julian; Gupta, Varun; Ramirez, J Roberto; Shack, R Bruce; Grotting, James C; Higdon, K Kye

    2015-11-01

    Among aesthetic surgery procedures, abdominoplasty is associated with a higher complication rate, but previous studies are limited by small sample sizes or single-institution experience. A cohort of patients who underwent abdominoplasty between 2008 and 2013 was identified from the CosmetAssure database. Major complications were recorded. Univariate and multivariate analysis was performed evaluating risk factors, including age, smoking, body mass index, sex, diabetes, type of surgical facility, and combined procedures. The authors identified 25,478 abdominoplasties from 183,914 procedures in the database. Of these, 8,975 patients had abdominoplasty alone and 16,503 underwent additional procedures. The number of complications recorded was 1,012 (4.0 percent overall rate versus 1.4 percent in other aesthetic surgery procedures). Of these, 31.5 percent were hematomas, 27.2 percent were infections and 20.2 percent were suspected or confirmed venous thromboembolism. On multivariate analysis, significant risk factors (p procedures (1.5), and procedure performance in a hospital or surgical center versus office-based surgical suite (1.6). Combined procedures increased the risk of complication (abdominoplasty alone, 3.1 percent; with liposuction, 3.8 percent; breast procedure, 4.3 percent; liposuction and breast procedure, 4.6 percent; body-contouring procedure, 6.8 percent; liposuction and body-contouring procedure, 10.4 percent). Abdominoplasty is associated with a higher complication rate compared with other aesthetic procedures. Combined procedures can significantly increase complication rates and should be considered carefully in higher risk patients. Risk, II.

  4. Caltrans : construction manual

    Science.gov (United States)

    2009-08-01

    Caltrans intends this manual as a resource for all personnel engaged in contract administration. The manual establishes policies and procedures for the construction phase of Caltrans projects. However, this manual is not a contract document. It impos...

  5. Manual on gamma radiography. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1992-01-01

    This booklet contains information about radiation protection procedures for gamma radiography as well as a basic guide to the principles of the production of ionizing radiation and to methods of radiation protection and dosimetry

  6. Operating manual for the High Flux Isotope Reactor: operating procedures, Part 2

    Energy Technology Data Exchange (ETDEWEB)

    None

    1982-11-01

    Information is presented concerning the research facilities; cooling systems; contaiment heating, ventilating, and air conditioning; emergency procedures; waste systems; on-site utilites; records and data accumulation; auxiliary equipment; and technical specifications requirement.

  7. Bilateral effects of hospital patient-safety procedures on nurses' job satisfaction.

    Science.gov (United States)

    Inoue, T; Karima, R; Harada, K

    2017-09-01

    The aim of this study was to examine how hospital patient-safety procedures affect the job satisfaction of hospital nurses. Additionally, we investigated the association between perceived autonomy and hospital patient-safety procedures and job satisfaction. Recently, measures for patient safety have been recognized as an essential requirement in hospitals. Hospital patient-safety procedures may enhance the job satisfaction of nurses by improving the quality of their work. However, such procedures may also decrease their job satisfaction by imposing excessive stress on nurses because they cannot make mistakes. The participants included 537 nurses at 10 private hospitals in Japan (The surveys were collected from March to July 2012). Factors related to hospital patient-safety procedures were demonstrated using factor analysis, and the associations between these factors and nurses' self-perceived autonomy and job satisfaction were examined using structural equation modelling. Five factors regarding hospital patient-safety procedures were extracted. Additionally, structural equation modelling revealed statistically significant associations between these factors and the nurses' self-perceived autonomy and job satisfaction. The findings showed that nurses' perceived autonomy of the workplace enhanced their job satisfaction and that their perceptions of hospital patient-safety procedures promoted their job satisfaction. However, some styles of chief nurses' leadership regarding patient safety restrict nurses' independent and autonomous decision-making and actions, resulting in a lowering of job satisfaction. This study demonstrated that hospital patient-safety procedures have ambiguous effects on nurses' job satisfaction. In particular, chief nurses' leadership relating to patient safety can have a positive or negative effect on nurses' job satisfaction. The findings indicated that hospital managers should demonstrate positive attitudes to improve patient safety for

  8. PFPF canister counter for foreign plutonium (PCAS-3) hardware operations and procedures manual

    International Nuclear Information System (INIS)

    Menlove, H.O.; Baca, J.; Kroncke, K.E.; Miller, M.C.; Takahashi, S.; Seki, S.; Inose, S.; Yamamoto, T.

    1993-01-01

    A neutron coincidence counter has been designed for the measurement of plutonium powder contained in tall storage canisters. The counter was designed for installation in the Plutonium Fuel Production Facility fabrication plant. Each canister contains from one to five cans of PuO 2 . The neutron counter measures the spontaneous-fission rate from the plutonium and, when this is combined with the plutonium isotopic ratios, the plutonium mass is determined. The system can accommodate plutonium loadings up to 12 kg, with 10 kg being a typical loading. Software has been developed to permit the continuous operation of the system in an unattended mode. Authentication techniques have been developed for the system. This manual describes the system and its operation and gives performance and calibration parameters for typical applications

  9. Research on advanced system safety assessment procedures (4)

    International Nuclear Information System (INIS)

    Suzuki, Kazuhiko; Shimada, Yukiyasu

    2001-03-01

    The past research reports in the area of safety engineering proposed the Computer-aided HAZOP system to be applied to Nuclear Reprocessing Facilities. Automated HAZOP system has great advantage compared with human analysts in terms of accuracy of the results, and time required to conduct HAZOP studies. This report surveys the literature on risk assessment and safety design based on the concept of independent protection layers (IPLs). Furthermore, to improve HAZOP System, tool is proposed to construct the basic model and the internal state model. Such HAZOP system is applied to analyze two kinds of processes, where the ability of the proposed system is verified. In addition, risk assessment support system is proposed to integrate safety design environment and assessment result to be used by other plants as well as to enable the underline plant to use other plants' information. This technique can be implemented using web-based safety information systems. (author)

  10. Procedures for self-assessment of operational safety

    International Nuclear Information System (INIS)

    1997-08-01

    Self-assessment processes have been continuously developed by nuclear organizations, including nuclear power plants. Currently, the nuclear industry and governmental organizations are showing an increasing interest in the implementation of this process as an effective way for improving safety performance. Self-assessment involves the use of different types of tools and mechanisms to assist the organizations in assessing their own safety performance against given standards. This helps to enhance the understanding of the need for improvements, the feeling of ownership in achieving them and and the safety culture as a whole. The concepts developed in this report present the basic approach to self-assessment taking into consideration experience gained during Operational Safety Review Team (OSART) missions, from organizations and utilities which have successfully implemented parts of a self-assessment programme and from meetings organized to discuss the subject

  11. Licensing procedures and safety criteria for research reactors in France

    International Nuclear Information System (INIS)

    Berry, J.L.; Lerouge, B.

    1983-01-01

    From the very beginning of the CEA up to now, a great deal of work has been devoted to the development and utilization of research reactors in France for the needs of fundamental and applied research, production of radioisotopes, and training. In recent years, new reactors were commissioned while others were decommissioned. Moreover some of the existing facilities underwent important modifications to comply with more severe safety criteria, increase the experimental capabilities or qualify new low-enrichment fuels for research reactors (Osiris and Isis). This paper summarizes the recent evolution of the French research reactor capacity, describes the licensing process, the main safety criteria which are taken into consideration, and associated safety research. At the end, a few considerations are given to the consequences of the Osiris core conversion. Safety of research reactors has been studied in detail and many improvements have been brought due to: implementation of a specific experimental program, and adaptation of safety principles and rules elaborated for power reactors. Research reactors in operation in France have been built within a 22 year period. Meanwhile, safety rules have been improved. Old reactors do not comply with all the new rules but modifications are continuously made: after analysis of incidents, when replacement of equipment has to be carried out, when an important modification (fuel conversion for example) is decided upon

  12. Licensing procedures and safety criteria for research reactors in France

    Energy Technology Data Exchange (ETDEWEB)

    Berry, J L; Lerouge, B [Centre d' Etudes Nucleaires de Saclay (France)

    1983-08-01

    From the very beginning of the CEA up to now, a great deal of work has been devoted to the development and utilization of research reactors in France for the needs of fundamental and applied research, production of radioisotopes, and training. In recent years, new reactors were commissioned while others were decommissioned. Moreover some of the existing facilities underwent important modifications to comply with more severe safety criteria, increase the experimental capabilities or qualify new low-enrichment fuels for research reactors (Osiris and Isis). This paper summarizes the recent evolution of the French research reactor capacity, describes the licensing process, the main safety criteria which are taken into consideration, and associated safety research. At the end, a few considerations are given to the consequences of the Osiris core conversion. Safety of research reactors has been studied in detail and many improvements have been brought due to: implementation of a specific experimental program, and adaptation of safety principles and rules elaborated for power reactors. Research reactors in operation in France have been built within a 22 year period. Meanwhile, safety rules have been improved. Old reactors do not comply with all the new rules but modifications are continuously made: after analysis of incidents, when replacement of equipment has to be carried out, when an important modification (fuel conversion for example) is decided upon.

  13. Risk and safety requirements for diagnostic and therapeutic procedures in allergology

    DEFF Research Database (Denmark)

    Kowalski, Marek L; Ansotegui, Ignacio; Aberer, Werner

    2016-01-01

    One of the major concerns in the practice of allergy is related to the safety of procedures for the diagnosis and treatment of allergic disease. Management (diagnosis and treatment) of hypersensitivity disorders involves often intentional exposure to potentially allergenic substances (during skin...... attempted to present general requirements necessary to assure the safety of these procedures. Following review of available literature a group of allergy experts within the World Allergy Organization (WAO), representing various continents and areas of allergy expertise, presents this report on risk...... associated with diagnostic and therapeutic procedures in allergology and proposes a consensus on safety requirements for performing procedures in allergy offices. Optimal safety measures including appropriate location, type and required time of supervision, availability of safety equipment, access...

  14. School Survey on Crime and Safety (SSOCS) 2000 Public-Use Data Files, User's Manual, and Detailed Data Documentation. [CD-ROM].

    Science.gov (United States)

    National Center for Education Statistics (ED), Washington, DC.

    This CD-ROM contains the raw, public-use data from the 2000 School Survey on Crime and Safety (SSOCS) along with a User's Manual and Detailed Data Documentation. The data are provided in SAS, SPSS, STATA, and ASCII formats. The User's Manual and the Detailed Data Documentation are provided as .pdf files. (Author)

  15. The environmental survey manual

    International Nuclear Information System (INIS)

    1987-08-01

    The purpose of this manual is to provide guidance to the Survey and Sampling and Analysis teams that conduct the one-time Environmental Survey of the major US Department of Energy (DOE) operating facilities. This manual includes a discussion of DOE's policy on environmental issues, a review of statutory guidance as it applies to the Survey, the procedures and protocols to be used by the Survey teams, criteria for the use of the Survey teams in evaluating existing environmental data for the Survey effort, generic technical checklists used in every Survey, health and safety guidelines for the personnel conducting the Survey, including the identification of potential hazards, prescribed protective equipment, and emergency procedures, the required formats for the Survey reports, guidance on identifying environmental problems that need immediate attention by the Operations Office responsible for the particular facility, and procedures and protocols for the conduct of sampling and analysis

  16. DoD Program for Stability of Civilian Employment: Policies, Procedures, and Programs Manual

    Science.gov (United States)

    1990-09-01

    history of treatment for mental or emotional problems) .......................................... 91 Severe distortion of limbs and/or spine (e.g., dwarfism ...Cancer-a history of cancer with complete recovery .................. 88 Cancer-undergoing surgical and/or medical treatment ............. 89 Mental...and therefore, the treatment each registrant must receive. e. Activities planning to fill positions through competitive procedures should

  17. 1979-80 Budget Process. Phase I: Educational Programs. Procedures Manual.

    Science.gov (United States)

    Los Angeles Community Coll. District, CA. Div. of Educational Planning and Development.

    As Proposition 13 necessitated more drastic curtailment of expenditures than had been anticipated when the modified zero-based operational plan for 1978-79 was devised, the budget development procedure was revised for 1979-80. The process is divided into three phases: educational programs, district fiscal plan, and the operational plan. This…

  18. The procedures manual of the Environmental Measurements Laboratory. Volume 2, 28. edition

    Energy Technology Data Exchange (ETDEWEB)

    Chieco, N.A. [ed.

    1997-02-01

    This report contains environmental sampling and analytical chemistry procedures that are performed by the Environmental Measurements Laboratory. The purpose of environmental sampling and analysis is to obtain data that describe a particular site at a specific point in time from which an evaluation can be made as a basis for possible action.

  19. Manual on therapeutic uses of iodine-131. Incorporating: Applications guide, procedures guide, basics guide

    International Nuclear Information System (INIS)

    1992-01-01

    This booklet contains information about procedures to protect hospital staff and visitors and families of patients treated with iodine 131 from exposure to radiation from I-131. It also includes a basic guide to the principles of the production of ionizing radiation and to methods of radiation protection and dosimetry

  20. Iodine-125 safety procedures in a biochemical laboratory

    International Nuclear Information System (INIS)

    1989-01-01

    Radioactive isotopes of iodine are of considerable importance in biochemical research and this 14 minute videotape is designed to give workers an introduction to the radiation safety aspects of their use. It deals with I-125, which is now generally used in preference to I-131, but the principles of safe working practice are the same for both isotopes. (author)

  1. Environmental contamination by cyclophosphamide preparation: Comparison of conventional manual production in biological safety cabinet and robot-assisted production by APOTECAchemo.

    Science.gov (United States)

    Schierl, Rudolf; Masini, Carla; Groeneveld, Svenja; Fischer, Elke; Böhlandt, Antje; Rosini, Valeria; Paolucci, Demis

    2016-02-01

    The aim of this study was to compare environmental contamination of cyclophosphamide (CP) during 1 week of drug compounding by conventional manual procedure in a biological safety cabinet (BSC) with laminar airflow and a new robotic drug preparation system (APOTECAchemo). During four consecutive days, similar numbers of infusion bags with cyclophosphamide were prepared with both techniques in a cross-over design. Wipe samples (49 for BSC, 50 for APOTECAchemo) were taken at several locations (gloves, infusion bags, trays, BSC-benches, floor) in the pharmacy and analyzed for CP concentrations by GC-MSMS (LOD 0.2 ng/sample). The detection rate was 70% in the BSC versus 15% in APOTECAchemo. During manual preparation of admixtures using BSC contamination with CP was below 0.001 ng/cm(2) at most locations, but significant on gloves (0.0004-0.0967 ng/cm(2)) and the majority (70%) of infusion bags (preparation by APOTECAchemo, gloves (1 of 8: 0.0007 ng/cm(2)) and infusion bags (3 of 20: 0.0005, 0.0019, 0.0094 ng/cm(2)) were considerably less contaminated. Residual contamination was found on the surfaces under the dosing device in the compounding area (0.0293-0.1603 ng/cm(2)) inside the robotic system. Compared to outcomes of other studies, our results underline good manufacturing procedures in this pharmacy with low contamination for both techniques (BSC and APOTECAchemo). Comparison of both preparation procedures validated that contamination of infusion bags was much lower by using the robotic system. © The Author(s) 2014.

  2. Human Factors Evaluation of Procedures for Periodic Safety Review of Yonggwang Unit no. 1, 2

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Yong Hee; Lee, Jung Woon; Park, Jae Chang (and others)

    2006-01-15

    This report describes the results of human factors assessment on the plant operating procedures as part of Periodic Safety Review(PSR) of Yonggwang Nuclear Power Plant Unit no. 1, 2. The suitability of item and appropriateness of format and structure in the key operating procedures of nuclear power plants were investigated by the review of plant operating experiences and procedure documents, field survey, and experimental assessment on some part of procedures. A checklist was used to perform this assessment and record the review results. The reviewed procedures include EOP(Emergency Operating Procedures), GOP(General Operating Procedures), AOP(Abnormal Operating Procedures), and management procedures of some technical departments. As results of the assessments, any significant problem challenging the safety was not found on the human factors in the operating procedures. However, several small items to be changed and improved were discovered. An action plan is recommended to accommodate the suggestions and review comments. It will enhance the plant safety on the operating procedure.

  3. Miravalles Geothermal Project: Portable Well Flow Test Equipment and Procedures Manual

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-05-01

    The well flow test program has been designed to facilitate the gathering of information, with portable test equipment, from various wells with regard to their capability of flow, the quality of steam produced at various back pressures, the composition and quantity of noncondensable gases flashed from the wells and the composition and quantity of solids in the well's liquid streams (brine). The test program includes procedures for obtaining the following basic flow data pertinent to the plant power cycle design: (1) Effluent steam and brine flows, pressures and temperatures; (2) Noncondensable and dissolved gas contents in steam and brine; (3) H{sub s}S content in gases formed; and (4) Solids content and chemical analysis of steam and brine.

  4. Safety and application of procedures or: how do ''they'' have to use operating procedures in nuclear power plants

    International Nuclear Information System (INIS)

    Dien, Y.

    1993-03-01

    Emergency procedures are inescapable aspects of safety. They can be seen as the laws to be respected in an accident situation. But as for all laws, there remains the problem of their application: should strict adherence to the procedure be imposed under all circumstances. Is this possible. Are there any potential risks with such a requirement. Or, on the contrary, should application be more ''open'', more flexible, allowing for adaptation to the actual situation. But what are the potential risks involved in this approach. Are these two approaches to the application of procedures mutually exclusive, or are they complementary. This paper analyzes the nature of the problem of application of procedures and proposes orientations for further thought on the matter. (author). 11 refs

  5. Propensity scores-potential outcomes framework to incorporate severity probabilities in the highway safety manual crash prediction algorithm.

    Science.gov (United States)

    Sasidharan, Lekshmi; Donnell, Eric T

    2014-10-01

    Accurate estimation of the expected number of crashes at different severity levels for entities with and without countermeasures plays a vital role in selecting countermeasures in the framework of the safety management process. The current practice is to use the American Association of State Highway and Transportation Officials' Highway Safety Manual crash prediction algorithms, which combine safety performance functions and crash modification factors, to estimate the effects of safety countermeasures on different highway and street facility types. Many of these crash prediction algorithms are based solely on crash frequency, or assume that severity outcomes are unchanged when planning for, or implementing, safety countermeasures. Failing to account for the uncertainty associated with crash severity outcomes, and assuming crash severity distributions remain unchanged in safety performance evaluations, limits the utility of the Highway Safety Manual crash prediction algorithms in assessing the effect of safety countermeasures on crash severity. This study demonstrates the application of a propensity scores-potential outcomes framework to estimate the probability distribution for the occurrence of different crash severity levels by accounting for the uncertainties associated with them. The probability of fatal and severe injury crash occurrence at lighted and unlighted intersections is estimated in this paper using data from Minnesota. The results show that the expected probability of occurrence of fatal and severe injury crashes at a lighted intersection was 1 in 35 crashes and the estimated risk ratio indicates that the respective probabilities at an unlighted intersection was 1.14 times higher compared to lighted intersections. The results from the potential outcomes-propensity scores framework are compared to results obtained from traditional binary logit models, without application of propensity scores matching. Traditional binary logit analysis suggests that

  6. Operational limits and conditions and operating procedures for nuclear power plants. Safety guide

    International Nuclear Information System (INIS)

    2005-01-01

    This Safety Guide was prepared as part of the Agency's programme for establishing safety standards relating to nuclear power plants. The present Safety Guide supersedes the IAEA Safety Guide on Operational Limits and Conditions for Nuclear Power Plants which was issued in 1979 as Safety Series No. 50-SG-O3. For a nuclear power plant to be operated in a safe manner, the provisions made in the final design and subsequent modifications shall be reflected in limitations on plant operating parameters and in the requirements on plant equipment and personnel. Under the responsibility of the operating organization, these shall be developed during the design safety evaluation as a set of operational limits and conditions (OLCs). A major contribution to compliance with the OLCs is made by the development and utilization of operating procedures (OPs) that are consistent with and fully implement the OLCs. The requirements for the OLCs and OPs are established in Section 5 of the IAEA Safety Requirements publication Safety of Nuclear Power Plants: Operation, which this Safety Guide supplements. The purpose of this Safety Guide is to provide guidance on the development, content and implementation of OLCs and OPs. The Safety Guide is directed at both regulators and owners/operators. This Safety Guide covers the concept of OLCs, their content as applicable to land based stationary power plants with thermal neutron reactors, and the responsibilities of the operating organization regarding their establishment, modification, compliance and documentation. The OPs to support the implementation of the OLCs and to ensure their observance are also within the scope of this Safety Guide. The particular aspects of the procedures for maintenance, surveillance, in-service inspection and other safety related activities in connection with the safe operation of nuclear power plants are outside the scope of this Safety Guide but can be found in other IAEA Safety Guides. Section 2 indicates the

  7. Operational limits and conditions and operating procedures for nuclear power plants. Safety guide

    International Nuclear Information System (INIS)

    2000-01-01

    This Safety Guide was prepared as part of the Agency's programme for establishing safety standards relating to nuclear power plants. The present Safety Guide supersedes the IAEA Safety Guide on Operational Limits and Conditions for Nuclear Power Plants which was issued in 1979 as Safety Series No. 50-SG-O3. For a nuclear power plant to be operated in a safe manner, the provisions made in the final design and subsequent modifications shall be reflected in limitations on plant operating parameters and in the requirements on plant equipment and personnel. Under the responsibility of the operating organization, these shall be developed during the design safety evaluation as a set of operational limits and conditions (OLCs). A major contribution to compliance with the OLCs is made by the development and utilization of operating procedures (OPs) that are consistent with and fully implement the OLCs. The requirements for the OLCs and OPs are established in Section 5 of the IAEA Safety Requirements publication Safety of Nuclear Power Plants: Operation, which this Safety Guide supplements. The purpose of this Safety Guide is to provide guidance on the development, content and implementation of OLCs and OPs. The Safety Guide is directed at both regulators and owners/operators. This Safety Guide covers the concept of OLCs, their content as applicable to land based stationary power plants with thermal neutron reactors, and the responsibilities of the operating organization regarding their establishment, modification, compliance and documentation. The OPs to support the implementation of the OLCs and to ensure their observance are also within the scope of this Safety Guide. The particular aspects of the procedures for maintenance, surveillance, in-service inspection and other safety related activities in connection with the safe operation of nuclear power plants are outside the scope of this Safety Guide but can be found in other IAEA Safety Guides. Section 2 indicates the

  8. Safety and feasibility of atrial fibrillation ablation using Amigo® system versus manual approach: A pilot study

    Directory of Open Access Journals (Sweden)

    Antonio Scarà

    2018-03-01

    Full Text Available Background: The Amigo® Remote Catheter System is a relatively new robotic system for catheter navigation. This study compared feasibility and safety using Amigo (RCM versus manual catheter manipulation (MCM to treat paroxysmal atrial fibrillation (PAF. Contact force (CF and force-time integral (FTI values obtained during pulmonary vein isolation (PVI ablation were compared. Methods: Forty patients were randomly selected for either RCM (20 or MCM (20. All were studied with the Thermocool® SmartTouch® force-sensing catheter (STc. Contact Force (CF, Force Time Integral (FTI and procedure-related data, were measured/stored in the CARTO®3. Results: All cases achieved complete PVI without major complications. Mean CF was significantly higher in the RCM group (13.3 ± 7.7 g in RCM vs. 12.04 ± 7.42 g in MCM p < 0.001, as was overall mean FTI (425.6 gs ± 199.6 gs with RCM and 407.5 gs ± 288.0 gs in MCM (p = 0.007 and was more likely to fall into the optimal FTI range (400-1000 using RCM (66.1% versus 49.1%, p < 0.001. FTI was significantly more likely to fall within the optimal range in each PV, as was CF within its optimal range in the right PVs, but trended higher in the left PVs. Freedom from atrial tachyarrhythmia was 90.0% for the RCM and 70.0% for the MCM group (p = 0,12 at 540 days follow-up. Conclusions: This pilot study suggests that use of the Amigo RCM system, with STc catheter, seems to be safe and effective for PVI ablation in paroxysmal AF patients. A not statistically significant favorable trend was observed for RCM in term of AF-free survival. Keywords: Atrial fibrillation, Catheter ablation, Remote robotic ablation

  9. Orientation to occupational safety compliance in DOE: Student manual, Book 1

    International Nuclear Information System (INIS)

    1993-01-01

    The purpose of this document is to present Federal safety and health program requirements, provide an overview of DOE Safety and Health Programs, and to present information on the changes presently underway in the Department of Energy regarding safety and health. Public Law 91--596, Executive Order 12196,29 CFR 1960 and various related DOE Orders will be presented

  10. Standards for radiation protection instrumentation: design of safety standards and testing procedures

    International Nuclear Information System (INIS)

    Meissner, Frank

    2008-01-01

    This paper describes by means of examples the role of safety standards for radiation protection and the testing and qualification procedures. The development and qualification of radiation protection instrumentation is a significant part of the work of TUV NORD SysTec, an independent expert organisation in Germany. The German Nuclear Safety Standards Commission (KTA) establishes regulations in the field of nuclear safety. The examples presented may be of importance for governments and nuclear safety authorities, for nuclear operators and for manufacturers worldwide. They demonstrate the advantage of standards in the design of radiation protection instrumentation for new power plants, in the upgrade of existing instrumentation to nuclear safety standards or in the application of safety standards to newly developed equipment. Furthermore, they show how authorities may proceed when safety standards for radiation protection instrumentation are not yet established or require actualization. (author)

  11. In-Office Endoscopic Laryngeal Laser Procedures: A Patient Safety Initiative.

    Science.gov (United States)

    Anderson, Jennifer; Bensoussan, Yael; Townsley, Richard; Kell, Erika

    2018-05-01

    Objective To review complications of in-office endoscopic laryngeal laser procedures after implementation of standardized safety protocol. Methods A retrospective review was conducted of the first 2 years of in-office laser procedures at St Michaels Hospital after the introduction of a standardized safety protocol. The protocol included patient screening, procedure checklist with standardized reporting of processes, medications, and complications. Primary outcomes measured were complication rates of in-office laryngeal laser procedures. Secondary outcomes included hemodynamic changes, local anesthetic dose, laser settings, total laser/procedure time, and incidence of sedation. Results A total of 145 in-office KTP procedures performed on 65 patients were reviewed. In 98% of cases, the safety protocol was fully implemented. The overall complication rate was 4.8%. No major complications were encountered. Minor complications included vasovagal episodes and patient intolerance. The rate of patient intolerance resulting early termination of anticipated procedure was 13.1%. Total local anesthetic dose averaged 172.9 mg lidocaine per procedure. The mean amount of laser energy dispersed was 261.2 J, with mean total procedure time of 48.3 minutes. Sixteen percent of patients had preprocedure sedation. Vital signs were found to vary modestly. Systolic blood pressure was lower postprocedure in 13.8% and symptomatic in 4.1%. Discussion The review of our standardized safety protocol has revealed that in-office laser treatment for laryngeal pathology has extremely low complication rates with safe patient outcomes. Implications for Practice The trend of shifting procedures out of the operating room into the office/clinic setting requires new processes designed to promote patient safety.

  12. Research on advanced system safety assessment procedures (II)

    International Nuclear Information System (INIS)

    Suzuki, Kazuhiko; Shimada, Yukiyasu

    1999-03-01

    HAZOP (Hazard and operability study) is a systematic technique, which requires the involvement of an experienced, interdisciplinary team of engineers, to identify hazards or operability problems throughout an entire facility by brainstorming. Though HAZOP is recognized as the useful safety assessment method, it requires a labor-intensive and time-consuming process. So recently computer-aided HAZOP has been proposed. The research report in 1998 (PNC PJ1612 98-001) presented prototype system, which carries out HAZOP and FT synthesis, by making use of proposed method. Relationships between states of input and output variables, internal and external events of each component are represented using decision tables, and the system is implemented by C++. In this study, the causalities of plant component malfunctions are described as component malfunction basic model and are stored in the computer. Thus, we have developed safety evaluation support system by considering the fault propagation path. Component malfunction basic model is made based on the information on the causalities between the abnormal state and each malfunction in components. This component malfunction basic model provides the common frame to describe abnormal situation in components. By using this basic model, not only state malfunction of component but also the consequence to external circumstance is assessed. G2, which is an excellent object-oriented developer tool in GUI (Graphical User Interface), is used as a tool for developing the system. By using the graphical editor in the system, the user can carry out HAZOP easily. We have applied this system to the Nuclear Reprocessing Facilities to demonstrate the utilities of developing system. (author)

  13. Laboratory manual on sample preparation procedures for x-ray micro-analysis

    International Nuclear Information System (INIS)

    1997-01-01

    X-ray micro fluorescence is a non-destructive and sensitive method for studying the microscopic distribution of different elements in almost all kinds of samples. Since the beginning of this century, x-rays and electrons have been used for the analysis of many different kinds of material. Techniques which rely on electrons are mainly developed for microscopic studies, and are used in conventional Electron Microscopy (EM) or Scanning Electron Microscopy (SEM), while x-rays are widely used for chemical analysis at the microscopic level. The first chemical analysis by fluorescence spectroscopy using small x-ray beams was conducted in 1928 by Glockner and Schreiber. Since then much work has been devoted to developing different types of optical systems for focusing an x-ray beam, but the efficiency of these systems is still inferior to the conventional electron optical systems. However, even with a poor optical efficiency, the x-ray microbeam has many advantages compared with electron or proton induced x-ray emission methods. These include: The analyses are non-destructive, losses of mass are negligible, and due to the low thermal loading of x-rays, materials which may be thermally degraded can be analysed; Samples can be analysed in air, and no vacuum is required, therefore specimens with volatile components such as water in biological samples, can be imaged at normal pressure and temperature; No charging occurs during analysis and therefore coating of the sample with a conductive layer is not necessary; With these advantages, simpler sample preparation procedures including mounting and preservation can be used

  14. Energy Research and Development Administration, Division of Safety, Standards, and Compliance respirator manual

    International Nuclear Information System (INIS)

    Douglas, D.D.; Hack, A.L.; Held, B.J.; Revoir, W.H.

    1976-05-01

    The manual has been prepared to provide technical information for contractors of the Energy Research and Development Administration (ERDA) on the application of respiratory protective devices for protection against airborne contaminants, both radioactive and nonradioactive. The various elements of a respirator program including selection and maintenance of equipment and training of personnel are described to assist in establishing adequate programs

  15. Energy Research and Development Administration, Division of Safety, Standards, and Compliance respirator manual

    Energy Technology Data Exchange (ETDEWEB)

    Douglas, D.D.; Hack, A.L.; Held, B.J.; Revoir, W.H.

    1976-05-01

    The manual has been prepared to provide technical information for contractors of the Energy Research and Development Administration (ERDA) on the application of respiratory protective devices for protection against airborne contaminants, both radioactive and nonradioactive. The various elements of a respirator program including selection and maintenance of equipment and training of personnel are described to assist in establishing adequate programs.

  16. Biosafety Manual

    Energy Technology Data Exchange (ETDEWEB)

    King, Bruce W.

    2010-05-18

    Work with or potential exposure to biological materials in the course of performing research or other work activities at Lawrence Berkeley National Laboratory (LBNL) must be conducted in a safe, ethical, environmentally sound, and compliant manner. Work must be conducted in accordance with established biosafety standards, the principles and functions of Integrated Safety Management (ISM), this Biosafety Manual, Chapter 26 (Biosafety) of the Health and Safety Manual (PUB-3000), and applicable standards and LBNL policies. The purpose of the Biosafety Program is to protect workers, the public, agriculture, and the environment from exposure to biological agents or materials that may cause disease or other detrimental effects in humans, animals, or plants. This manual provides workers; line management; Environment, Health, and Safety (EH&S) Division staff; Institutional Biosafety Committee (IBC) members; and others with a comprehensive overview of biosafety principles, requirements from biosafety standards, and measures needed to control biological risks in work activities and facilities at LBNL.

  17. Research on advanced system safety assessment procedures (III)

    International Nuclear Information System (INIS)

    Suzuki, Kazuhiko; Shimada, Yukiyasu

    2000-03-01

    Though HAZOP is recognized as the useful safety assessment method, it requires a labor-intensive and time-consuming process. So recently computer-aided HAZOP has been proposed. The research report in 1999 (PNC TJ1400 99-003) presented HAZOP system based on the plant component malfunctions basic models. By using this basic model, not only state malfunction of component but also the consequence to external circumstance can be assessed. G2, which is an excellent object-oriented developer tool in GUI (Graphical User Interface), was used as a tool for developing the system. By using the graphical editor in the system, the user can carry out HAZOP easily. The purpose of this research is to improve the ability of the HAZOP system to obtain a more detailed HAZOP results. HAZOP is carried out according to the fault propagation of component level and the one of plant level based on plant component malfunctions basic models. Furthermore, the HAZOP system which can do the cause and effect analysis in detail intended for the component which processes two or more materials is developed. It is possible to carry out HAZOP for various plants by newly adding material information to the knowledge base. We have applied this system to the Nuclear Reprocessing Facilities to demonstrate the utilities of developing system. (author)

  18. Program Management System manual

    International Nuclear Information System (INIS)

    1986-01-01

    The Program Management System (PMS), as detailed in this manual, consists of all the plans, policies, procedure, systems, and processes that, taken together, serve as a mechanism for managing the various subprograms and program elements in a cohesive, cost-effective manner. The PMS is consistent with the requirements of the Nuclear Waste Policy Act of 1982 and the ''Mission Plan for the Civilian Radioactive Waste Management Program'' (DOE/RW-0005). It is based on, but goes beyond, the Department of Energy (DOE) management policies and procedures applicable to all DOE programs by adapting these directives to the specific needs of the Civilian Radioactive Waste Management program. This PMS Manual describes the hierarchy of plans required to develop and maintain the cost, schedule, and technical baselines at the various organizational levels of the Civilian Radioactive Waste Management Program. It also establishes the management policies and procedures used in the implementation of the Program. These include requirements for internal reports, data, and other information; systems engineering management; regulatory compliance; safety; quality assurance; and institutional affairs. Although expanded versions of many of these plans, policies, and procedures are found in separate documents, they are an integral part of this manual. The PMS provides the basis for the effective management that is needed to ensure that the Civilian Radioactive Waste Management Program fulfills the mandate of the Nuclear Waste Policy Act of 1982. 5 figs., 2 tabs

  19. Safety panel and new procedures evaluation by simulator tests

    International Nuclear Information System (INIS)

    Meslin, T.

    1986-01-01

    With more than thirty weeks of simulator testing (for the last three years only) and approximately three hundred scenarios, EDF's experience in this field is extensive. This practice is well known within Fossil and Nuclear Generation and is well accepted by the operating teams which participate in it. Simulator testing appears to be an essential decision-making tool in the process of developing new operating aids in PWR plants. Accelerated development and the elimination of long and expensive modifications after commissioning is an economic advantage. The saving in time is obvious, since modifications are carried out continuously throughout the development phase. Finally, operators participate in the development of systems and receive fixed, well-defined applications. This practice has become systematic, and all new applications concerning the operation of PWR plants are simulator-tested, particularly 1300-MW unit computers and operating procedures, the new generation of 900-MW unit computers, and the new 1500-MW fully computerized control rooms. Finally, this simulator testing allows us to considerably increase our knowledge concerning the behavior of operators in accident situations, and special tests are performed for this purpose

  20. Manual on Safety Aspects of the Design and Equipment of Hot Laboratories

    International Nuclear Information System (INIS)

    1969-01-01

    With the development of atomic energy application and research, hot laboratories are now being constructed in a number of countries. The present publication describes and discusses experience in several countries in designing equipment for these laboratories. The safe handling of highly radioactive substances is the main purpose of hot laboratory design and equipment. The manual aims at helping those persons, particularly in the developing countries, who plan to design and construct a new hot laboratory or modify an existing one. It does not deal in great detail with the engineering design of protective and handling equipment; these matters can be found in the comprehensive list of references. The manual itself covers only basic ideas and different approaches in the design of laboratory building, hot cells, shielded and glove boxes, fume cupboards, and handling and viewing equipment. Systems for transferring materials and main services are also discussed.

  1. Safety management procedures and practices at Indira Gandhi Centre for Atomic Research

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, P.; Lee, S.M.; Kapoor, R.P.; Raghunath, V.M.; Karthikeyan, S.V. [Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India)]. E-mail: kapoor@igcar.ernet.in

    2004-07-01

    The Indira Gandhi Centre for Atomic Research (IGCAR) operates FBTR (Fast Breeder Test Reactor), KAMINI (neutron source reactor), radiometallurgical laboratory, radiochemical laboratory, reprocessing plant, industrial scale sodium loops, advanced research laboratories, workshops, etc. Codified safety management procedures with systematic surveillance are essential for safe and reliable operations and these are described under the classifications of radiation safety, industrial safety and reactor operations with special emphasis on the human factor. Health physics teams, independent of the plant facility, supervise the radioactive facilities of the centre. Industrial safety standards are maintained by another independent section. Safety management for the reactors include a clear organisational structure, adequate documentation, compulsory training and licencing, safe working methods taking into account human factors and review by independent safety authorities. (author)

  2. Safety management procedures and practices at Indira Gandhi Centre for Atomic Research

    International Nuclear Information System (INIS)

    Rodriguez, P.; Lee, S.M.; Kapoor, R.P.; Raghunath, V.M.; Karthikeyan, S.V.

    2004-01-01

    The Indira Gandhi Centre for Atomic Research (IGCAR) operates FBTR (Fast Breeder Test Reactor), KAMINI (neutron source reactor), radiometallurgical laboratory, radiochemical laboratory, reprocessing plant, industrial scale sodium loops, advanced research laboratories, workshops, etc. Codified safety management procedures with systematic surveillance are essential for safe and reliable operations and these are described under the classifications of radiation safety, industrial safety and reactor operations with special emphasis on the human factor. Health physics teams, independent of the plant facility, supervise the radioactive facilities of the centre. Industrial safety standards are maintained by another independent section. Safety management for the reactors include a clear organisational structure, adequate documentation, compulsory training and licencing, safe working methods taking into account human factors and review by independent safety authorities. (author)

  3. Occupational Safety and Health Program Guidelines for Colleges and Universities. An Administrative Resource Manual.

    Science.gov (United States)

    Godbey, Frank W.; Hatch, Loren L.

    Designed as an aid for establishing and strengthening occupational safety and health programs on college and university campuses, this administrator guide is divided into four chapters. The first chapter defines and gives background information on the Occupational Safety and Health Act (OSHA). In addition, it presents a discussion of what the OSHA…

  4. Programing Procedures Manual (PPM).

    Science.gov (United States)

    1981-12-15

    terms ’reel’, ’unit’, and ’volume’ are synonymous and completely interchangeable in the CLOSE statement. Treatment of sequential mass storage files is...logically equivalent to the treatment of a file on tape or analogous sequential media. * For the purpose of showing the effect of various types of CLOSE...Overlay Area CA6 Address of Abend Relative to beginning of overlay segment The programer can now refer to the compile source listing for the overlay

  5. Risk and safety requirements for diagnostic and therapeutic procedures in allergology: World Allergy Organization Statement

    Directory of Open Access Journals (Sweden)

    Marek L. Kowalski

    2016-10-01

    Full Text Available Abstract One of the major concerns in the practice of allergy is related to the safety of procedures for the diagnosis and treatment of allergic disease. Management (diagnosis and treatment of hypersensitivity disorders involves often intentional exposure to potentially allergenic substances (during skin testing, deliberate induction in the office of allergic symptoms to offending compounds (provocation tests or intentional application of potentially dangerous substances (allergy vaccine to sensitized patients. These situations may be associated with a significant risk of unwanted, excessive or even dangerous reactions, which in many instances cannot be completely avoided. However, adverse reactions can be minimized or even avoided if a physician is fully aware of potential risk and is prepared to appropriately handle the situation. Information on the risk of diagnostic and therapeutic procedures in allergic diseases has been accumulated in the medical literature for decades; however, except for allergen specific immunotherapy, it has never been presented in a systematic fashion. Up to now no single document addressed the risk of the most commonly used medical procedures in the allergy office nor attempted to present general requirements necessary to assure the safety of these procedures. Following review of available literature a group of allergy experts within the World Allergy Organization (WAO, representing various continents and areas of allergy expertise, presents this report on risk associated with diagnostic and therapeutic procedures in allergology and proposes a consensus on safety requirements for performing procedures in allergy offices. Optimal safety measures including appropriate location, type and required time of supervision, availability of safety equipment, access to specialized emergency services, etc. for various procedures have been recommended. This document should be useful for allergists with already established

  6. Improvement of the safety level of installations with the generalization of procedures

    International Nuclear Information System (INIS)

    Cornille, Y.; Dupraz, B.; Schektman, N.

    1986-06-01

    The generalization of control procedures to the largest possible spectra of accidental situations which is being developed on pressurized water reactor units will allow to increase the safety level of these installations. This improvement has been quantified for some situations pointing out an appreciable mitigation of meltdown risk which could result. A new improvement is aimed with the definition and the utilization of new procedures ''by states'' which will allow an optimized treatment of situations resulting from multiple failures, now treated in the procedures SPI - SPU - U1. The needs related to these procedures and their development led to joint research and development programs between Electricite de France and the Institute of Protection and Nuclear Safety [fr

  7. The Effectiveness and Safety of Manual Therapy on Pain and Disability in Older Persons With Chronic Low Back Pain: A Systematic Review.

    Science.gov (United States)

    de Luca, Katie E; Fang, Sheng Hung; Ong, Justin; Shin, Ki-Soo; Woods, Samuel; Tuchin, Peter J

    2017-09-01

    The aim of this study was to perform a systematic review of the literature of the effectiveness and safety of manual therapy interventions on pain and disability in older persons with chronic low back pain (LBP). A literature search of 4 electronic databases was performed (PubMed, EMBASE, OVID, and CINAHL). Inclusion criteria included randomized controlled trials of manual therapy interventions on older persons who had chronic LBP. Effectiveness was determined by extracting and examining outcomes for pain and disability, with safety determined by the report of adverse events. The PEDro scale was used for quality assessment of eligible studies. The search identified 405 articles, and 38 full-text articles were assessed. Four studies met the inclusion criteria. All trials were of good methodologic quality and had a low risk of bias. The included studies provided moderate evidence supporting the use of manual therapy to reduce pain levels and alleviate disability. A limited number of studies have investigated the effectiveness and safety of manual therapy in the management of older people with chronic LBP. The current evidence to make firm clinical recommendations is limited. Research with appropriately designed trials to investigate the effectiveness and safety of manual therapy interventions in older persons with chronic LBP is required. Copyright © 2017. Published by Elsevier Inc.

  8. Procedures for treating common cause failures in safety and reliability studies: Procedural framework and examples

    International Nuclear Information System (INIS)

    Mosleh, A.; Fleming, K.N.; Parry, G.W.; Paula, H.M.; Worledge, D.H.; Rasmuson, D.M.

    1988-01-01

    This report presents a framework for the inclusion of the impact of common cause failures in risk and reliability evaluations. Common cause failures are defined as that cutset of dependent failures for which causes are not explicitly included in the logic model as basic events. The emphasis here is on providing procedures for a practical, systematic approach that can be used to perform and clearly document the analysis. The framework comprises four major stages: (1) System Logic Model Development; (2) Identification of Common Cause Component Groups; (3) Common Cause Modeling and Data Analysis; and (4) System Quantification and Interpretation of Results. The framework and the methods discussed for performing the different stages of the analysis integrate insights obtained from engineering assessments of the system and the historical evidence from multiple failure events into a systematic, reproducible, and defensible analysis. 22 figs., 34 tabs

  9. Application of condition-based HRA method for a manual actuation of the safety features in a nuclear power Plant

    International Nuclear Information System (INIS)

    Kang, Hyun Gook; Jang, Seung-Cheol

    2006-01-01

    A practical approach to develop a more realistic fault-tree model with a consideration of various conditions endured by a human operator is proposed. In safety-critical systems, the generation failure of an actuation signal is caused by the concurrent failures of the automated systems and an operator action. These two sources of safety signals are complicatedly correlated. The failures of sensors or automated systems will cause a lack of necessary information for a human operator and result in error-forcing contexts such as the loss of corresponding alarms and indications. It is well known that the error-forcing contexts largely affect the operator's performance. An automated system which consists of multiple processing channels and complex components is also affected by the availability of the sensors. This paper proposes a condition-based human reliability assessment (CBHRA) method in order to address these complicated conditions in a practical way. We apply the CBHRA method to the manual actuation of the safety features such as a reactor trip and auxiliary feedwater actuation in Korean Standard Nuclear Power Plants. Even the human error probability of each given condition is simply assumed, the application results prove that the CBHRA effectively accommodates the complicated error-forcing contexts into the fault trees

  10. Safety evaluation by living probabilistic safety assessment. Procedures and applications for planning of operational activities and analysis of operating experience

    International Nuclear Information System (INIS)

    Johanson, Gunnar; Holmberg, J.

    1994-01-01

    Living Probabilistic Safety Assessment (PSA) is a daily safety management system and it is based on a plant-specific PSA and supporting information systems. In the living use of PSA, plant status knowledge is used to represent actual plant safety status in monitoring or follow-up perspective. The PSA model must be able to express the risk at a given time and plant configuration. The process, to update the PSA model to represent the current or planned configuration and to use the model to evaluate and direct the changes in the configuration, is called living PSA programme. The main purposes to develop and increase the usefulness of living PSA are: Long term safety planning: To continue the risk assessment process started with the basic PSA by extending and improving the basic models and data to provide a general risk evaluation tool for analyzing the safety effects of changes in plant design and procedures. Risk planning of operational activities: To support the operational management by providing means for searching optimal operational maintenance and testing strategies from the safety point of view. The results provide support for risk decision making in the short term or in a planning mode. The operational limits and conditions given by technical specifications can be analyzed by evaluating the risk effects of alternative requirements in order to balance the requirements with respect to operational flexibility and plant economy. Risk analysis of operating experience: To provide a general risk evaluation tool for analyzing the safety effects of incidents and plant status changes. The analyses are used to: identify possible high risk situations, rank the occurred events from safety point of view, and get feedback from operational events for the identification of risk contributors. This report describes the methods, models and applications required to continue the process towards a living use of PSA. 19 tabs, 20 figs

  11. Safety Precautions and Operating Procedures in an (A)BSL-4 Laboratory: 4. Medical Imaging Procedures.

    Science.gov (United States)

    Byrum, Russell; Keith, Lauren; Bartos, Christopher; St Claire, Marisa; Lackemeyer, Matthew G; Holbrook, Michael R; Janosko, Krisztina; Barr, Jason; Pusl, Daniela; Bollinger, Laura; Wada, Jiro; Coe, Linda; Hensley, Lisa E; Jahrling, Peter B; Kuhn, Jens H; Lentz, Margaret R

    2016-10-03

    Medical imaging using animal models for human diseases has been utilized for decades; however, until recently, medical imaging of diseases induced by high-consequence pathogens has not been possible. In 2014, the National Institutes of Health, National Institute of Allergy and Infectious Diseases, Integrated Research Facility at Fort Detrick opened an Animal Biosafety Level 4 (ABSL-4) facility to assess the clinical course and pathology of infectious diseases in experimentally infected animals. Multiple imaging modalities including computed tomography (CT), magnetic resonance imaging, positron emission tomography, and single photon emission computed tomography are available to researchers for these evaluations. The focus of this article is to describe the workflow for safely obtaining a CT image of a live guinea pig in an ABSL-4 facility. These procedures include animal handling, anesthesia, and preparing and monitoring the animal until recovery from sedation. We will also discuss preparing the imaging equipment, performing quality checks, communication methods from "hot side" (containing pathogens) to "cold side," and moving the animal from the holding room to the imaging suite.

  12. A combined deterministic and probabilistic procedure for safety assessment of components with cracks - Handbook.

    Energy Technology Data Exchange (ETDEWEB)

    Dillstroem, Peter; Bergman, Mats; Brickstad, Bjoern; Weilin Zang; Sattari-Far, Iradj; Andersson, Peder; Sund, Goeran; Dahlberg, Lars; Nilsson, Fred (Inspecta Technology AB, Stockholm (Sweden))

    2008-07-01

    SSM has supported research work for the further development of a previously developed procedure/handbook (SKI Report 99:49) for assessment of detected cracks and tolerance for defect analysis. During the operative use of the handbook it was identified needs to update the deterministic part of the procedure and to introduce a new probabilistic flaw evaluation procedure. Another identified need was a better description of the theoretical basis to the computer program. The principal aim of the project has been to update the deterministic part of the recently developed procedure and to introduce a new probabilistic flaw evaluation procedure. Other objectives of the project have been to validate the conservatism of the procedure, make the procedure well defined and easy to use and make the handbook that documents the procedure as complete as possible. The procedure/handbook and computer program ProSACC, Probabilistic Safety Assessment of Components with Cracks, has been extensively revised within this project. The major differences compared to the last revision are within the following areas: It is now possible to deal with a combination of deterministic and probabilistic data. It is possible to include J-controlled stable crack growth. The appendices on material data to be used for nuclear applications and on residual stresses are revised. A new deterministic safety evaluation system is included. The conservatism in the method for evaluation of the secondary stresses for ductile materials is reduced. A new geometry, a circular bar with a circumferential surface crack has been introduced. The results of this project will be of use to SSM in safety assessments of components with cracks and in assessments of the interval between the inspections of components in nuclear power plants

  13. Evaluation procedure of software safety plan for digital I and C of KNGR

    International Nuclear Information System (INIS)

    Lee, Jang Soo; Park, Jong Kyun; Lee, Ki Young; Kwon, Ki Choon; Kim, Jang Yeol; Cheon, Se Woo

    2000-05-01

    The development, use, and regulation of computer systems in nuclear reactor instrumentation and control (I and C) systems to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Korean next generation reactor (KNGR) software safety verification and validation (SSVV) task, Korea Atomic Energy Research Institute, which investigates different aspects of computer software in reactor I and C systems, and describes the engineering procedures for developing such a software. The purpose of this guideline is to give the software safety evaluator the trail map between the code and standards layer and the design methodology and documents layer for the software important to safety in nuclear power plants. Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organizations. The requirements for software important to safety of nuclear reactor are described in such positions and standards, for example, the new standard review plan (SRP), IEC 880 supplements, IEEE standard 1228-1994, IEEE standard 7-4.3.2-1993, and IAEA safety series No. 50-SG-D3 and D8. We presented the guidance for evaluating the safety plan of the software in the KNGR protection systems. The guideline consists of the regulatory requirements for software safety in chapter 2, the evaluation checklist of software safety plan in chapter3, and the evaluation results of KNGR software safety plan in chapter 4

  14. Evaluation procedure of software safety plan for digital I and C of KNGR

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jang Soo; Park, Jong Kyun; Lee, Ki Young; Kwon, Ki Choon; Kim, Jang Yeol; Cheon, Se Woo

    2000-05-01

    The development, use, and regulation of computer systems in nuclear reactor instrumentation and control (I and C) systems to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Korean next generation reactor (KNGR) software safety verification and validation (SSVV) task, Korea Atomic Energy Research Institute, which investigates different aspects of computer software in reactor I and C systems, and describes the engineering procedures for developing such a software. The purpose of this guideline is to give the software safety evaluator the trail map between the code and standards layer and the design methodology and documents layer for the software important to safety in nuclear power plants. Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organizations. The requirements for software important to safety of nuclear reactor are described in such positions and standards, for example, the new standard review plan (SRP), IEC 880 supplements, IEEE standard 1228-1994, IEEE standard 7-4.3.2-1993, and IAEA safety series No. 50-SG-D3 and D8. We presented the guidance for evaluating the safety plan of the software in the KNGR protection systems. The guideline consists of the regulatory requirements for software safety in chapter 2, the evaluation checklist of software safety plan in chapter3, and the evaluation results of KNGR software safety plan in chapter 4.

  15. Radiological safety problems in intracavitary brachytherapy using the manual afterloading in Venezuela

    International Nuclear Information System (INIS)

    Lea, D.; Gonzales, E.; Gallardo, J.; Diaz, M.

    1996-01-01

    In three venezuelan public hospitals it was detected radioactive contamination for Cs-137 during inspection with the wipe test technique in areas where is applied intracavitary brachytherapy using manual afterloading. This caused a condition of great stress in the personal engaged the treatments. In each Cs-137 source in these hospitals was tested leakage. The source plastic holder was analysed. The authors were able to demonstrate: a) The radioactive contamination found in the treatment area had its origin in the Cs-137 capsule corrosion and b) The corrosion in the source capsule was produced by the radiolytic degradation of the PVC tube used as source-holder in the intracavitary treatments. (authors). 3 refs., 1 tab

  16. Health and Safety Research Division manual for the x-ray facility in Building 2008

    International Nuclear Information System (INIS)

    Stansbury, P.S.

    1977-11-01

    The facility in the east end of Building 2008, ORNL, consists of an x-ray machine and a shielded enclosure. The x-ray machine is of the constant potential type and can be operated continuously at generating potentials up to 125 kVcp with tube currents ranging from 0.1 μA to 10 mA. Both the generating potential and the tube current are highly regulated and stabilized. The machine is installed and operated within a large shielded enclosure. In addition to the x-ray machine and its ancillary equipment, the shielded enclosure contains many of the features of a general chemistry and physics laboratory including work benches, sinks, storage space, and electrical and gas service. This manual contains instructions for the safe operation of the x-ray machine

  17. 49 CFR 214.337 - On-track safety procedures for lone workers.

    Science.gov (United States)

    2010-10-01

    ...-track equipment is not impaired by background noise, lights, precipitation, fog, passing trains, or any... performing routine inspection or minor correction may use individual train detection to establish on-track... worker retains an absolute right to use on-track safety procedures other than individual train detection...

  18. 75 FR 34064 - Manufactured Home Construction and Safety Standards, Test Procedures for Roof Trusses

    Science.gov (United States)

    2010-06-16

    ... failure. Failure is rupture, fracture, or excessive yielding. (v) Final recovery phase. Remove 2.0 times... members of the public. Commenters should follow the instructions provided on that site to submit comments... nondestructive testing procedure for roof trusses that permits a lower overall factor of safety to be used in...

  19. Updated procedure for the safety evaluation of natural flavor complexes used as ingredients in food

    NARCIS (Netherlands)

    Cohen, Samuel M.; Eisenbrand, Gerhard; Fukushima, Shoji; Gooderham, Nigel J.; Guengerich, F.P.; Hecht, Stephen S.; Rietjens, Ivonne M.C.M.; Davidsen, Jeanne M.; Harman, Christie L.; Taylor, Sean V.

    2018-01-01

    An effective and thorough approach for the safety evaluation of natural flavor complexes (NFCs) was published in 2005 by the Expert Panel of the Flavor and Extract Manufacturers Association (FEMA). An updated procedure is provided here, which maintains the essential concepts of the use of the

  20. Meat safety consequences of implementing visual postmortem meat inspection procedures in Danish slaughter pigs

    DEFF Research Database (Denmark)

    Mousing, Jan; Kyrval, J.; Jensen, Tim Kåre

    1997-01-01

    The consequences of a change from a traditional meat inspection procedure, including manual handling, palpation and incision, to an entirely postmortem meat inspection procedure in Danish slaughter pigs were assessed by a comparative study of the two methods in 188,383 slaughter pigs. Out of 58...... lesion codes (selected with a prevalence less-than-or-equal-to 5.5 x 10(-5)), 26 (45 percent) were assessed either as merely aesthetic or as the healed stage of an earlier lesion and nine (15 percent) as active, but local processes, occurring only in non-edible tissue. Five lesion codes (9 percent) were...... assessed as active, non-abscessal processes occurring in edible tissue, caused by swine-specific pathogens and 10 (17 percent) were abscessal or pyaemic lesions occurring in edible tissue. Seven lesion codes (12 percent) may be associated with consumer health hazards (two frequently and five rarely...

  1. Procedure for getting safety classed concrete structures approved by Finnish Radiation and Nuclear Safety Authority

    International Nuclear Information System (INIS)

    Halme, Ville-Juhani

    2015-01-01

    Posiva is preparing geological final disposal in the Finnish bedrock in Olkiluoto, Eurajoki. The final disposal facility includes encapsulation plant and underground repository. Most of the main civil structures are concrete structures. STUK is the supervising authority in civil structures. The National Building Code of Finland and STUK's Regulatory Guide on nuclear safety (YVL) are the most important instructions when constructing concrete structures into nuclear installation. Posiva has classified concrete structures in two classes according STUK's YVL-guidance: EYT (non-nuclear) and Safety Class 3 (SC 3, nuclear safety significance). When building SC 3 concrete structures, specific protocol must be followed. Protocol includes planned routines for design, construction, supervision, quality control (QC) and quality assurance (QA) activities. Documents relating concrete structures must be approved by Posiva and STUK before construction work. After structures have been designed and actual building is ongoing, there are two main steps. Before concreting, readiness inspection for concreting must be arranged. Readiness inspection will be arranged according to a specific plan and the date must be informed to STUK. After establishing readiness for concreting, casting work can begin. Once concrete structures are done, inspected and approved, final documentation according to a quality control plan will be reviewed by Posiva. After Posiva's approval, final documentation will be sent for STUK's approval. In the end STUK will give the permission for commissioning of the concrete structures after approved commissioning inspection. The document is made up of an abstract and a poster

  2. Radiation protection in dentistry. Recommended safety procedures for the use of dental x-ray equipment. Safety code 30

    International Nuclear Information System (INIS)

    1994-01-01

    The Radiation Protection Bureau has prepared a series of documents on safety codes to set out requirements for the safe use of radiation-emitting equipment. This Safety Code has been prepared to provide specific guidance to the dentist, dental hygienist, dental assistant and other support personnel concerned with safety procedures and equipment performance. Dental radiography is one of the most valuable tools used in modern dental health care. It makes possible the diagnosis of physical conditions that would otherwise be difficult to identify. The use of dental radiological procedures must be carefully managed, because x-radiation has the potential for damaging healthy cells and tissues. Although no known occurrence of cancer or genetic damage has been observed from radiation doses delivered in modern dentistry, and until more evidence is available, one should practice radiation hygiene with the same care as would be dictated if a hazard were known to exist. The aim of radiation protection in dentistry is to obtain the desired clinical information with minimal radiation exposure to patients, dental personnel and the public. 15 tabs

  3. Radiation protection in dentistry. Recommended safety procedures for the use of dental x-ray equipment. Safety code 30

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    The Radiation Protection Bureau has prepared a series of documents on safety codes to set out requirements for the safe use of radiation-emitting equipment. This Safety Code has been prepared to provide specific guidance to the dentist, dental hygienist, dental assistant and other support personnel concerned with safety procedures and equipment performance. Dental radiography is one of the most valuable tools used in modern dental health care. It makes possible the diagnosis of physical conditions that would otherwise be difficult to identify. The use of dental radiological procedures must be carefully managed, because x-radiation has the potential for damaging healthy cells and tissues. Although no known occurrence of cancer or genetic damage has been observed from radiation doses delivered in modern dentistry, and until more evidence is available, one should practice radiation hygiene with the same care as would be dictated if a hazard were known to exist. The aim of radiation protection in dentistry is to obtain the desired clinical information with minimal radiation exposure to patients, dental personnel and the public. 15 tabs.

  4. The significance of the probabilistic safety analysis (PSA) in administrative procedures under nuclear law

    International Nuclear Information System (INIS)

    Berg, H.P.

    1994-01-01

    The probabilistic safety analysis (PSA) is a useful tool for safety relevant evaluation of nuclear power plant designed on the basis of deterministic specifications. The PSA yields data identifying reliable or less reliable systems, or frequent or less frequent failure modes to be taken into account for safety engineering. Performance of a PSA in administrative procedures under nuclear law, e.g. licensing, is an obligation laid down in a footnote to criterion 1.1 of the BMI safety criteria catalogue, which has been in force unaltered since 1977. The paper explains the application and achievements of PSA in the phase of reactor development concerned with the conceptual design basis and design features, using as an example the novel PWR. (orig./HP) [de

  5. Improving the safety and quality of nursing care through standardized operating procedures in Bosnia and Herzegovina.

    Science.gov (United States)

    Ausserhofer, Dietmar; Rakic, Severin; Novo, Ahmed; Dropic, Emira; Fisekovic, Eldin; Sredic, Ana; Van Malderen, Greet

    2016-06-01

    We explored how selected 'positive deviant' healthcare facilities in Bosnia and Herzegovina approach the continuous development, adaptation, implementation, monitoring and evaluation of nursing-related standard operating procedures. Standardized nursing care is internationally recognized as a critical element of safe, high-quality health care; yet very little research has examined one of its key instruments: nursing-related standard operating procedures. Despite variability in Bosnia and Herzegovina's healthcare and nursing care quality, we assumed that some healthcare facilities would have developed effective strategies to elevate nursing quality and safety through the use of standard operating procedures. Guided by the 'positive deviance' approach, we used a multiple-case study design to examine a criterion sample of four facilities (two primary healthcare centres and two hospitals), collecting data via focus groups and individual interviews. In each studied facility, certification/accreditation processes were crucial to the initiation of continuous development, adaptation, implementation, monitoring and evaluation of nursing-related SOPs. In one hospital and one primary healthcare centre, nurses working in advanced roles (i.e. quality coordinators) were responsible for developing and implementing nursing-related standard operating procedures. Across the four studied institutions, we identified a consistent approach to standard operating procedures-related processes. The certification/accreditation process is enabling necessary changes in institutions' organizational cultures, empowering nurses to take on advanced roles in improving the safety and quality of nursing care. Standardizing nursing procedures is key to improve the safety and quality of nursing care. Nursing and Health Policy are needed in Bosnia and Herzegovina to establish a functioning institutional framework, including regulatory bodies, educational systems for developing nurses' capacities or the

  6. Use of safety analysis to site comfirmation procedure in case of hard rock repository

    International Nuclear Information System (INIS)

    Peltonen, E.K.

    1984-02-01

    The role of safety analysis in a confirmation procedure of a candidate disposal site of radioactive wastes is discussed. Items dealt with include principle reasons and practical goals of the use of safety analysis, methodology of safety analysis and assessment, as well as usefulness and adequacy of the present safety analysis. Safety analysis is a tool, which enables one to estimate quantitatively the possible radiological impacts from the disposal. The results can be compared with the criteria and the suitability conclusions drawn. Because of its systems analytical nature safety analysis is an effective method to reveal, what are the most important factors of the disposal system and the most critical site characteristics inside the lumped parameters often provided by the experimental site investigation methods. Furthermore it gives information on the accuracy needs of different site properties. This can be utilized to judge whether the quality and quantity of the measurements for the characterization are sufficient as well as to guide the further site investigations. A more practical discussion regarding the applicability of the use of safety analysis is presented by an example concerning the assessment of a Finnish candidate site for low- and intermediate-level radioactive waste repository. (author)

  7. Safety code 19: recommended safety procedures for the selection, installation and use of x-ray diffraction equipment

    International Nuclear Information System (INIS)

    1984-01-01

    This document is one of a series of Safety Codes prepared by the Radiation Protection Bureau to set out requirements for the safe use of radiation emitting devices. The equipment and installation guidelines and safety procedures detailed in this Code are primarily for the instruction and guidance of persons employed in Federal Public Service Departments and Agencies, as well as those coming under the jurisdiction of the Canada Labour Code. This Safety Code is also intended to assist other users of X-ray diffraction equipment to select safe equipment and to install and use it so that the radiation hazard to the operator and other persons in its vicinity is negligible. It should be noted that facilities under provincial jurisdiction may be subject to requirements specified under provincial statutes. This Code supersedes Safety Code RPD-SC-7, entitled 'Requirements For Non-Medical X-Ray Equipment, Use and Installation', insofar as X-ray diffraction equipment is concerned, and it is intended to complement X-ray equipment design, construction and performance standards promulgated under the Radiation Emitting Devices Act

  8. The Safety Assessment of OPR-1000 for Station Blackout Applying Combined Deterministic and Probabilistic Procedure

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Dong Gu; Ahn, Seung-Hoon; Cho, Dae-Hyung [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2015-05-15

    This is termed station blackout (SBO). However, it does not generally include the loss of available AC power to safety buses fed by station batteries through inverters or by alternate AC sources. Historically, risk analysis results have indicated that SBO was a significant contributor to overall core damage frequency. In this study, the safety assessment of OPR-1000 nuclear power plant for SBO accident, which is a typical beyond design basis accident and important contributor to overall plant risk, is performed by applying the combined deterministic and probabilistic procedure (CDPP). In addition, discussions are made for reevaluation of SBO risk at OPR-1000 by eliminating excessive conservatism in existing PSA. The safety assessment of OPR-1000 for SBO accident, which is a typical BDBA and significant contributor to overall plant risk, was performed by applying the combined deterministic and probabilistic procedure. However, the reference analysis showed that the CDF and CCDP did not meet the acceptable risk, and it was confirmed that the SBO risk should be reevaluated. By estimating the offsite power restoration time appropriately, the SBO risk was reevaluated, and it was finally confirmed that current OPR-1000 system lies in the acceptable risk against the SBO. In addition, it was demonstrated that the proposed CDPP is applicable to safety assessment of BDBAs in nuclear power plants without significant erosion of the safety margin.

  9. Development of a draft of human factors safety review procedures for the Korean next generation reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jung Woon; Moon, B. S.; Park, J. C.; Lee, Y. H.; Oh, I. S.; Lee, H. C. [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-02-01

    In this study, a draft of human factors engineering (HFE) safety review procedures (SRP) was developed for the safety review of KNGR based on HFE Safety and Regulatory Requirements and Guidelines (SRRG). This draft includes acceptance criteria, review procedure, and evaluation findings for the areas of review including HFE Program Management, Human Factors Analyses, Human Factors Design, and HFE Verification and Validation, based on Section 15.1 'Human Factors Engineering Design Process' and 15.2 'Control Room Human Factors Engineering' of KNGR Specific Safety Requirements and Chapter 15 'Human Factors Engineering' of KNGR Safety Regulatory Guides. For the effective review, human factors concerns or issues related to advanced HSI design that have been reported so far should be extensively examined. In this study, a total of 384 human factors issues related to the advanced HSI design were collected through our review of a total of 145 documents. A summary of each issue was described and the issues were identified by specific features of HSI design. These results were implemented into a database system. 8 refs., 2 figs. (Author)

  10. Development of a draft of human factors safety review procedures for the Korean Next Generation Reactor

    International Nuclear Information System (INIS)

    Lee, Jung Woon; Moon, B. S.; Park, J. C.; Lee, Y. H.; Oh, I. S.; Lee, H. C.

    2000-02-01

    In this study, a draft of Human Factors Engineering (HFE) Safety Review Procedures (SRP) was developed for the safety review of KNGR based on HFE Safety and Regulatory Requirements and Guidelines (SRRG). This draft includes acceptance criteria, review procedure, and evaluation findings for the areas of review including HFE program management, human factors analyses, human factors design, and HFE verification and validation, based on section 15.1 'human factors engineering design process' and 15.2 'control room human factors engineering' of KNGR specific safety requirements and chapter 15 'human factors engineering' of KNGR safety regulatory guides. For the effective review, human factors concerns or issues related to advanced HSI design that have been reported so far should be extensively examined. In this study, a total of 384 human factors issues related to the advanced HSI design were collected through our review of a total of 145 documents. A summary of each issue was described and the issues were identified by specific features of HSI design. These results were implemented into a database system

  11. Evaluating North Carolina Food Pantry Food Safety-Related Operating Procedures.

    Science.gov (United States)

    Chaifetz, Ashley; Chapman, Benjamin

    2015-11-01

    Almost one in seven American households were food insecure in 2012, experiencing difficulty in providing enough food for all family members due to a lack of resources. Food pantries assist a food-insecure population through emergency food provision, but there is a paucity of information on the food safety-related operating procedures used in the pantries. Food pantries operate in a variable regulatory landscape; in some jurisdictions, they are treated equivalent to restaurants, while in others, they operate outside of inspection regimes. By using a mixed methods approach to catalog the standard operating procedures related to food in 105 food pantries from 12 North Carolina counties, we evaluated their potential impact on food safety. Data collected through interviews with pantry managers were supplemented with observed food safety practices scored against a modified version of the North Carolina Food Establishment Inspection Report. Pantries partnered with organized food bank networks were compared with those that operated independently. In this exploratory research, additional comparisons were examined for pantries in metropolitan areas versus nonmetropolitan areas and pantries with managers who had received food safety training versus managers who had not. The results provide a snapshot of how North Carolina food pantries operate and document risk mitigation strategies for foodborne illness for the vulnerable populations they serve. Data analysis reveals gaps in food safety knowledge and practice, indicating that pantries would benefit from more effective food safety training, especially focusing on formalizing risk management strategies. In addition, new tools, procedures, or policy interventions might improve information actualization by food pantry personnel.

  12. Transition to Office-based Obstetric and Gynecologic Procedures: Safety, Technical, and Financial Considerations.

    Science.gov (United States)

    Peacock, Lisa M; Thomassee, May E; Williams, Valerie L; Young, Amy E

    2015-06-01

    Office-based surgery is increasingly desired by patients and providers due to ease of access, overall efficiency, reimbursement, and satisfaction. The adoption of office-based surgery requires careful consideration of safety, efficacy, cost, and feasibility within a providers practice. This article reviews the currently available data regarding patient and provider satisfaction as well as practical considerations of staffing, equipment, and supplies. To aid the practitioner, issues of office-based anesthesia and safety with references to currently available national guidelines and protocols are provided. Included is a brief review of billing, coding, and reimbursement. Technical procedural aspects with information and recommendations are summarized.

  13. Safety procedures in operation of inspection and maintenance of pressure reduction and metering stations

    International Nuclear Information System (INIS)

    Villas Boas, Ademar Jose; Biesemeyer, Marco Aurelio R.

    2000-01-01

    Each local Natural Gas Distribution Company in Brazil has its own working procedures for operations of inspection and maintenance on equipment and accessories connected to the gas network. Some of these Companies developed a better elaborated and documented way of working routines, while others only work based on their operators experience. The objective of this work is to create a standard procedure for operations of inspection and maintenance of Pressure Reducing Stations and Metering Stations, mainly the ones concerned to safety aspects. This work has no intention of exhausting all aspects related to this subject but to become the first step to standardize these types of operations among Natural Gas Distribution Companies. (author)

  14. Introductory user's manual for the US Nuclear Regulatory Commission Reactor Safety Research Data Bank

    International Nuclear Information System (INIS)

    Scofield, N.R.; Hardy, H.A.; Laats, E.T.

    1983-02-01

    The United States Nuclear Regulatory Commission (NRC) has established the NRC/Division of Accident Evaluation (DAE) Data Bank Program to collect, store, and make available data from the many domestic and foreign water safety research programs. Local direction of the program is provided by E G and G Idaho, Inc., prime contractor for the Department of Energy (DOE) at the Idaho National Engineering Laboratory (INEL). The NRC/DAE Data Bank Program provides a central computer storage mechanism and access software for data that is to be used by code development and assessment groups in meeting the code and correlation needs of the nuclear industry. The administrative portion of the program provides data entry, documentation, training, and advisory services to users and the NRC. The NRC/DAE Data Bank and the capabilities of the data access software are described

  15. Introductory user's manual for the US Nuclear Regulatory Commission Reactor Safety Research Data Bank

    International Nuclear Information System (INIS)

    Scofield, N.R.; Hardy, H.A.; Laats, E.T.

    1984-03-01

    The United States NRC has established the NRC/Division of Accident Evaluation (DAE) Data Bank Program to collect, store, and make available data from the many domestic and foreign water reactor safety research programs. Local direction of the program is provided by EG and G Idaho, Inc., prime contractor for the Department of Energy (DOE) at the Idaho National Engineering Laboratory (INEL). The NRC/DAE Data Bank Program provides a central computer storage mechanism and access software for data that is to be used by code development and assessment groups in meeting the code and correlation needs of the nuclear industry. The administrative portion of the program provides data entry, documentation, training, and advisory services to users and the NRC. The NRC/DAE Data Bank and the capabilities of the data access software are described in this document

  16. Introductory user's manual for the US Nuclear Regulatory Commission Reactor Safety Research Data Bank. Revision 3

    International Nuclear Information System (INIS)

    Hardy, H.A.; Laats, E.T.

    1985-03-01

    The United States Nuclear Regulatory Commission (USNRC) has established the NRC/Division of Accident Evaluation (DAE) Data Bank Program to collect, store, and make available data from the many domestic and foreign water reactor safety research programs. Local direction of the program is provided by EG and G Idaho, Inc., prime contractor for the Department of Energy (DOE) at the Idaho National Engineering Laboratory (INEL). The NRC/DAE Data Bank Program provides a central computer storage mechanism and access software for data to be used by code development and assessment groups in meeting the code correlation needs of the nuclear industry. The administrative portion of the program provides data entry, documentation, training, and advisory services to users and the USNRC. The NRC/DAE Data Bank and the capabilities of the data access software are described in this document

  17. An innovative 3-D numerical modelling procedure for simulating repository-scale excavations in rock - SAFETI

    Energy Technology Data Exchange (ETDEWEB)

    Young, R. P.; Collins, D.; Hazzard, J.; Heath, A. [Department of Earth Sciences, Liverpool University, 4 Brownlow street, UK-0 L69 3GP Liverpool (United Kingdom); Pettitt, W.; Baker, C. [Applied Seismology Consultants LTD, 10 Belmont, Shropshire, UK-S41 ITE Shrewsbury (United Kingdom); Billaux, D.; Cundall, P.; Potyondy, D.; Dedecker, F. [Itasca Consultants S.A., Centre Scientifique A. Moiroux, 64, chemin des Mouilles, F69130 Ecully (France); Svemar, C. [Svensk Karnbranslemantering AB, SKB, Aspo Hard Rock Laboratory, PL 300, S-57295 Figeholm (Sweden); Lebon, P. [ANDRA, Parc de la Croix Blanche, 7, rue Jean Monnet, F-92298 Chatenay-Malabry (France)

    2004-07-01

    This paper presents current results from work performed within the European Commission project SAFETI. The main objective of SAFETI is to develop and test an innovative 3D numerical modelling procedure that will enable the 3-D simulation of nuclear waste repositories in rock. The modelling code is called AC/DC (Adaptive Continuum/ Dis-Continuum) and is partially based on Itasca Consulting Group's Particle Flow Code (PFC). Results are presented from the laboratory validation study where algorithms and procedures have been developed and tested to allow accurate 'Models for Rock' to be produced. Preliminary results are also presented on the use of AC/DC with parallel processors and adaptive logic. During the final year of the project a detailed model of the Prototype Repository Experiment at SKB's Hard Rock Laboratory will be produced using up to 128 processors on the parallel super computing facility at Liverpool University. (authors)

  18. Procedures for conducting probabilistic safety assessment for non-reactor nuclear facilities

    International Nuclear Information System (INIS)

    2002-01-01

    A well performed and adequately documented safety assessment of a nuclear facility will serve as a basis to determine whether the facility complies with the safety objectives, principles and criteria as stipulated by the national regulatory body of the country where the facility is in operation. International experience shows that the practices and methodologies used to perform safety assessments and periodic safety re-assessment for non-reactor nuclear facilities differ significantly from county to country. Most developing countries do not have methods and guidance for safety assessment that are prescribed by the regulatory body. Typically the safety evaluation for the facility is based on a case by case assessment. Whilst conservative deterministic analyses are predominantly used as a licensing basis in many countries, recently probabilistic safety assessment (PSA) techniques have been applied as a useful complementary tool to support safety decision making. The main benefit of PSA is to provide insights into the safety aspects of facility design and operation. PSA points up the potential environmental impacts of postulated accidents, including the dominant risk contributors, and enables safety analysts to compare options for reducing risk. In order to advise on how to apply PSA methodology for the safety assessment of non-reactor nuclear facilities, the IAEA organized several consultants meetings, which led to the preparation of this TECDOC. This document is intended as guidance for the conduct of PSA in non-nuclear facilities. The main emphasis here is on the general procedural steps of a PSA that is specific for a non-reactor nuclear facility, rather than the details of the specific methods. The report is directed at technical staff managing or performing such probabilistic assessments and to promote a standardized framework, terminology and form of documentation for these PSAs. It is understood that the level of detail implied in the tasks presented in this

  19. PSAPACK 4.2. A code for probabilistic safety assessment level 1. User`s manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Only limited use has been made until now of the large amount of information contained in probabilistic safety assessments (PSAs). This is mainly due to the complexity of the PSA reports and the difficulties in obtaining intermediate results and in performing updates and recalculations. Moreover, PSA software was developed for mainframe computers, and the files of information such as fault trees and accident sequences were intended for the use of the analysts carrying out PSA studies or other skilled PSA practitioners. The increasing power and availability of personal computers (PCs) and developments in recent years in both hardware and software have made it possible to develop PSA software for use in PCs. Furthermore, the operational characteristics of PCs make them attractive not only for performing PSAs but also for updating the results and in using them in day-to-day applications. The IAEA has therefore developed in co-operation with its Member States, a software package (PSAPACK) for PCs for use in performing a Level 1 PSA and for easy interrogation of the results. Figs.

  20. PSAPACK 4.2. A code for probabilistic safety assessment level 1. User's manual

    International Nuclear Information System (INIS)

    1995-01-01

    Only limited use has been made until now of the large amount of information contained in probabilistic safety assessments (PSAs). This is mainly due to the complexity of the PSA reports and the difficulties in obtaining intermediate results and in performing updates and recalculations. Moreover, PSA software was developed for mainframe computers, and the files of information such as fault trees and accident sequences were intended for the use of the analysts carrying out PSA studies or other skilled PSA practitioners. The increasing power and availability of personal computers (PCs) and developments in recent years in both hardware and software have made it possible to develop PSA software for use in PCs. Furthermore, the operational characteristics of PCs make them attractive not only for performing PSAs but also for updating the results and in using them in day-to-day applications. The IAEA has therefore developed in co-operation with its Member States, a software package (PSAPACK) for PCs for use in performing a Level 1 PSA and for easy interrogation of the results. Figs

  1. Procedures for conducting common cause failure analysis in probabilistic safety assessment

    International Nuclear Information System (INIS)

    1992-05-01

    The principal objective of this report is to supplement the procedure developed in Mosleh et al. (1988, 1989) by providing more explicit guidance for a practical approach to common cause failures (CCF) analysis. The detailed CCF analysis following that procedure would be very labour intensive and time consuming. This document identifies a number of options for performing the more labour intensive parts of the analysis in an attempt to achieve a balance between the need for detail, the purpose of the analysis and the resources available. The document is intended to be compatible with the Agency's Procedures for Conducting Probabilistic Safety Assessments for Nuclear Power Plants (IAEA, 1992), but can be regarded as a stand-alone report to be used in conjunction with NUREG/CR-4780 (Mosleh et al., 1988, 1989) to provide additional detail, and discussion of key technical issues

  2. Improving Safety on the International Space Station: Transitioning to Electronic Emergency Procedure Books on the International Space Station

    Science.gov (United States)

    Carter-Journet, Katrina; Clahoun, Jessica; Morrow, Jason; Duncan, Gary

    2012-01-01

    The National Aeronautics and Space Administration (NASA) originally designed the International Space Station (ISS) to operate until 2015, but have extended operations until at least 2020. As part of this very dynamic Program, there is an effort underway to simplify the certification of Commercial ]of ]the ]Shelf (COTS) hardware. This change in paradigm allows the ISS Program to take advantage of technologically savvy and commercially available hardware, such as the iPad. The iPad, a line of tablet computers designed and marketed by Apple Inc., was chosen to support this endeavor. The iPad is functional, portable, and could be easily accessed in an emergency situation. The iPad Electronic Flight Bag (EFB), currently approved for use in flight by the Federal Aviation Administration (FAA), is a fraction of the cost of a traditional Class 2 EFB. In addition, the iPad fs ability to use electronic aeronautical data in lieu of paper in route charts and approach plates can cut the annual cost of paper data in half for commercial airlines. ISS may be able to benefit from this type of trade since one of the most important factors considered is information management. Emergency procedures onboard the ISS are currently available to the crew in paper form. Updates to the emergency books can either be launched on an upcoming visiting vehicle such as a Russian Soyuz flight or printed using the onboard ISS printer. In both cases, it is costly to update hardcopy procedures. A new operations concept was proposed to allow for the use of a tablet system that would provide a flexible platform to support space station crew operations. The purpose of the system would be to provide the crew the ability to view and maintain operational data, such as emergency procedures while also allowing Mission Control Houston to update the procedures. The ISS Program is currently evaluating the safety risks associated with the use of iPads versus paper. Paper products can contribute to the flammability

  3. NASA Spinoff Article: Automated Procedures To Improve Safety on Oil Rigs

    Science.gov (United States)

    Garud, Sumedha

    2013-01-01

    On May 11th, 2013, two astronauts emerged from the interior of the International Space Station (ISS) and worked their way toward the far end of spacecraft. Over the next 51/2 hours, the two replaced an ammonia pump that had developed a significant leak a few days before. On the ISS, ammonia serves the vital role of cooling components-in this case, one of the station's eight solar arrays. Throughout the extravehicular activity (EVA), the astronauts stayed in constant contact with mission control: every movement, every action strictly followed a carefully planned set of procedures to maximize crew safety and the chances of success. Though the leak had come as a surprise, NASA was prepared to handle it swiftly thanks in part to the thousands of procedures that have been written to cover every aspect of the ISS's operations. The ISS is not unique in this regard: Every NASA mission requires well-written procedures-or detailed lists of step-by-step instructions-that cover how to operate equipment in any scenario, from normal operations to the challenges created by malfunctioning hardware or software. Astronauts and mission control train and drill extensively in procedures to ensure they know what the proper procedures are and when they should be used. These procedures used to be exclusively written on paper, but over the past decade, NASA has transitioned to digital formats. Electronic-based documentation simplifies storage and use, allowing astronauts and flight controllers to find instructions more quickly and display them through a variety of media. Electronic procedures are also a crucial step toward automation: once instructions are digital, procedure display software can be designed to assist in authoring, reviewing, and even executing them.

  4. Fire Safety Trianing in Health Care Institutions.

    Science.gov (United States)

    American Hospital Association, Chicago, IL.

    The manual details the procedures to be followed in developing and implementing a fire safety plan. The three main steps are first, to organize; second, to set up a procedure and put it in writing; and third, to train and drill employees and staff. Step 1 involves organizing a safety committee, appointing a fire marshall, and seeking help from…

  5. A procedure for safety assessment of components with cracks - Handbook. 3rd revised edition

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, P.; Bergman, M.; Brickstad, B.; Dahlberg, L.; Nilsson, F.; Sattari-Far, I. [SAQ Kontroll AB, Stockholm (Sweden)

    1999-12-01

    In this handbook a procedure is described which can be used both for assessment of detected cracks or crack-like defects and for defect tolerance analysis. The procedure can be used to calculate possible crack growth due to fatigue or stress corrosion and to calculate the reserve margin for failure due to fracture and plastic collapse. For ductile materials, the procedure gives the reserve margin for initiation of stable crack growth. Thus, an extra reserve margin, unknown to size, exists for failure in components made of ductile materials. The procedure was developed for operative use with the following objectives in mind: a) The procedure should be able to handle both linear and non-linear problems without any a priori division. b) The procedure shall ensure uniqueness of the safety assessment. c) The procedure should be well defined and easy to use. d) The conservatism of the procedure should be well validated. e) The handbook, that documents the procedure, should be so complete that for most assessments, access to any other fracture mechanics literature should not be necessary. The method utilized in the procedure is based on the R6-method developed at Nuclear Electric plc. The basic assumption is that fracture initiated by a crack can be described by the variables K{sub r} and L{sub r}. K{sub r} is the ratio between the stress intensity factor and the fracture toughness of the material. L{sub r} is the ratio between applied load and the plastic limit load of the structure. The pair of calculated values of these variables is plotted in a diagram. If the point is situated within the noncritical region, fracture is assumed not to occur. If the point is situated outside the region, crack growth and fracture may occur. The method can in principal be used for all metallic materials. It is, however, more extensively verified for steel alloys only. The method is not intended for use in temperature regions where creep deformation is of importance. To fulfil the above

  6. A procedure for safety assessment of components with cracks - Handbook. 3rd revised edition

    International Nuclear Information System (INIS)

    Andersson, P.; Bergman, M.; Brickstad, B.; Dahlberg, L.; Nilsson, F.; Sattari-Far, I.

    1999-12-01

    In this handbook a procedure is described which can be used both for assessment of detected cracks or crack-like defects and for defect tolerance analysis. The procedure can be used to calculate possible crack growth due to fatigue or stress corrosion and to calculate the reserve margin for failure due to fracture and plastic collapse. For ductile materials, the procedure gives the reserve margin for initiation of stable crack growth. Thus, an extra reserve margin, unknown to size, exists for failure in components made of ductile materials. The procedure was developed for operative use with the following objectives in mind: a) The procedure should be able to handle both linear and non-linear problems without any a priori division. b) The procedure shall ensure uniqueness of the safety assessment. c) The procedure should be well defined and easy to use. d) The conservatism of the procedure should be well validated. e) The handbook, that documents the procedure, should be so complete that for most assessments, access to any other fracture mechanics literature should not be necessary. The method utilized in the procedure is based on the R6-method developed at Nuclear Electric plc. The basic assumption is that fracture initiated by a crack can be described by the variables K r and L r . K r is the ratio between the stress intensity factor and the fracture toughness of the material. L r is the ratio between applied load and the plastic limit load of the structure. The pair of calculated values of these variables is plotted in a diagram. If the point is situated within the noncritical region, fracture is assumed not to occur. If the point is situated outside the region, crack growth and fracture may occur. The method can in principal be used for all metallic materials. It is, however, more extensively verified for steel alloys only. The method is not intended for use in temperature regions where creep deformation is of importance. To fulfil the above given objectives

  7. Goldmann applanation tonometry over daily disposable contact lens: accuracy and safety of procedure.

    Science.gov (United States)

    Zeri, Fabrizio; Lupelli, Luigi; Formichella, Paolo; Masci, Carlo; Fletcher, Robert

    2007-09-01

    To study accuracy and safety, related to sensation (discomfort) and trauma, when using Goldmann applanation tonometry (GAT) on eyes wearing daily disposable soft contact lenses. The intra-ocular pressure (IOP) of 136 normal eyes of 68 subjects was measured by Goldmann tonometer. Measurements were made in one eye with a contact lens (hilafilcon A) without anaesthetic drops and then without the contact lens using one drop of 0.4% oxybuprocaine hydrochloride. Each contact lens used was identical as to back optic zone, back vertex power. Standard Goldmann procedure only was used for the fellow eye of each subject. Subjective sensation (discomfort) responses to both procedures were studied in a subgroup (66 eyes) using a scale of discomfort, from 1 (no sensation) to 5 (highest sensation). Epithelial staining after tonometry was evaluated for this subgroup. No significant differences were found for the IOP with and without contact lens (tcontact lens insertion, tonometry on contact lens and application of topical anaesthetic). Corneal epithelial staining following the standard tonometry procedure was significantly higher than following the procedure with a contact lens (pcontact lens is accurate, compared to the standard procedure and within the IOP's normal range studied here. Also using a contact lens results in less trauma whilst discomfort is similar.

  8. Safety of Running Two Rooms: A Systematic Review and Meta-Analysis of Overlapping Neurosurgical Procedures.

    Science.gov (United States)

    Self, D Mitchell; Ilyas, Adeel; Stetler, William R

    2018-04-27

    Overlapping surgery, a long-standing practice within academic neurosurgery centers nationwide, has recently come under scrutiny from the government and media as potentially harmful to patients. Therefore, the objective of this systematic review and meta-analysis is to determine the safety of overlapping neurosurgical procedures. The authors performed a systematic review and meta-analysis in accordance with PRISMA guidelines. A review of PubMed and Medline databases was undertaken with the search phrase "overlapping surgery AND neurosurgery AND outcomes." Data regarding patient demographics, type of neurosurgical procedure, and outcomes and complications were extracted from each study. The principle summary measure was odds ratio (OR) of the association of overlapping versus non-overlapping surgery with outcomes. The literature search yielded a total of 36 studies, of which 5 studies met inclusion criteria and were included in this study. These studies included a total of 25,764 patients undergoing neurosurgical procedures. Overlapping surgery was associated with an increased likelihood of being discharged home (OR = 1.32; 95% CI 1.20 to 1.44; P < 0.001) and a reduced 30-day unexpected return to the operating room (OR = 0.79; 95% CI 0.72 to 0.87; P < 0.001). Overlapping surgery did not significantly affect OR of length of surgery, 30-day mortality, or 30-day readmission. Overlapping neurosurgical procedures were not associated with worse patient outcomes. Additional, prospective studies are needed to further assess the safety overlapping procedures. Copyright © 2018. Published by Elsevier Inc.

  9. Manual for best practice for emergency response procedures, part 2: the management of inrushes, fires, explosions and other emergencies.

    CSIR Research Space (South Africa)

    Spencer, KC

    2000-02-01

    Full Text Available to the strong likelihood of low visibility, disorientation and psychological trauma that can exist following a fire or explosion in a colliery, it is imperative that adequate provision be made to ensure that affected persons reach a place of safety... on the job safety training. 3.3 Locating the refuge bay or place of safety Having to escape in adverse conditions (i.e. zero visibility) can cause considerable psychological trauma and panic. It is therefore suggested that as part of the initial...

  10. Case of sudden death following rupture of thoracic aortic aneurysm during “a manual therapy” procedure in the spinal area

    Directory of Open Access Journals (Sweden)

    Aleksandra Kaczorowska

    2015-03-01

    Full Text Available The reported case concerns the rupture of an aneurysm located in the descending part of the thoracic aorta during the procedure of the so-called “spinal adjustment” performed by a chiropractor. A 45-year-old patient with no significant medical history of cardiovascular diseases visited, along with his wife, one of “manual therapy” practices because of back pain. During the procedure, the patient suddenly lost consciousness. Despite cardiopulmonary resuscitation and emergency assistance given by an ambulance team, the patient died. An autopsy revealed that the cause of death was increasing cardiorespiratory failure secondary to bleeding into the lumen of the left pleural cavity following the rupture of pathologically altered thoracic aortic wall.

  11. Methane measurements manual; Handbok metanmaetningar

    Energy Technology Data Exchange (ETDEWEB)

    Holmgren, Magnus Andreas (SP Technical research institute of Sweden, Boraas (Sweden))

    2011-02-15

    Emissions to air in different parts of the system may arise in biogas plants, where there is biological treatment of organic matter by anaerobic degradation, and during upgrading of biogas to vehicle fuel. There are mainly four reasons why these emissions must be minimized. These are safety, greenhouse gas emissions, economy and smell. This manual gathers experience of several years of work with measurement of methane emissions from biogas and upgrading facilities. This work has been done mainly in the context of Swedish Waste Management's system of voluntary commitment. The purpose of this manual is to standardize methods and procedures when methane measurements are carried out so that the results are comparable between different providers. The main target group of the manual is measurement consultants performing such measurements. Calculation template in Excel is part of the manual, which further contributes to the measurements evaluated in a standardized way. The manual contains several examples which have been calculated in the accompanying Excel template. The handbook also contains a chapter mainly intended for facility staff, in which implementation of accurate leak detection is described, and where there are hints of a system of so-called intermediate inspections to detect leaks in time

  12. Procedure proposed for performance of a probabilistic safety analysis for the event of ''Air plane crash''

    International Nuclear Information System (INIS)

    Hoffmann, H.H.

    1998-01-01

    A procedures guide for a probabilistic safety analysis for the external event 'Air plane crash' has been prepared. The method is based on analysis done within the framework of PSA for German NPPs as well as on international documents. Both crashes of military air planes and commercial air planes contribute to the plant risk. For the determination of the plant related crash rate the air traffic will be divided into 3 different categories of air traffic: - The landing and takeoff phase, - the airlane traffic and waiting loop traffic, - the free air traffic, and the air planes into different types and weight classes. (orig./GL) [de

  13. Procedures for controlling the risks of reliability, safety, and availability of technical systems

    International Nuclear Information System (INIS)

    1987-01-01

    The reference book covers four sections. Apart from the fundamental aspects of the reliability problem, of risk and safety and the relevant criteria with regard to reliability, the material presented explains reliability in terms of maintenance, logistics and availability, and presents procedures for reliability assessment and determination of factors influencing the reliability, together with suggestions for systems technical integration. The reliability assessment consists of diagnostic and prognostic analyses. The section on factors influencing reliability discusses aspects of organisational structures, programme planning and control, and critical activities. (DG) [de

  14. Safety of liver biopsy as a day procedure in Abuth Zaria, Nigeria

    International Nuclear Information System (INIS)

    Samuel, D.O.; Okuleke, I.P.

    2012-01-01

    Chronic liver disease (CLD) is an important condition, diagnosed mainly by liver biopsy and is a leading cause of death among the working class group. It is a major burden in sub-Saharan Africa where it leads to hepatocellular carcinoma with a high mortality. This study was a retrospective one undertaken to determine the safety of performing liver biopsy procedure between January 2000 to January 2009 in terms of the frequency of indications and side effects. A total of 279 entries were found out of which 270 (96.77%) had a definitive liver biopsy histology result. The main indication for liver biopsy was chronic viral hepatitis in 150 patients (53.76%) while the commonest complication was the post-procedure pain that was seen in 16 patients (5.7%). The average duration of hospital stay after biopsy was 6.08 +- 0.52 hours. (author)

  15. Surgical procedures performed in the neonatal intensive care unit on critically ill neonates: feasibility and safety

    International Nuclear Information System (INIS)

    Mallick, M.S.; Jado, A.M.; Al-Bassam, A.R.

    2008-01-01

    Transferring unstable, ill neonates to and from the operating rooms carries significant risks and can lead to morbidity. We report on our experience in performing certain procedures in critically ill neonates in the neonatal intensive care unit (NICU). We examined the feasibility and safety for such an approach. All surgical procedures performed in the NICU between January 1999 and December 2005 were analyzed in terms of demographic data, diagnosis, preoperative stability of the patient, procedures performed, complications and outcome. Operations were performed at beside in the NICU in critically ill, unstable neonates who needed emergency surgery, in neonates of low birth weight (<1000 gm) and in neonates on special equipments like higher frequency ventilators and nitrous oxide. Thirty-seven surgical procedures were performed including 12 laparotomies, bowel resection and stomies, 7 repairs of congenital diaphragmatic hernias, 4 ligations of patent ductus arteriosus and various others. Birth weights ranged between 850 gm and 3500 gm (mean 2000 gm). Gestational age ranged between 25 to 42 weeks (mean, 33 weeks). Age at surgery was between 1 to 30 days (mean, 30 days). Preoperatively, 19 patients (51.3%) were on inotropic support and all were intubated and mechanically ventilated. There was no mortality related to surgical procedures. Postoperatively, one patient developed wound infection and disruption. Performing major surgical procedures in the NICU is both feasible and safe. It is useful in very low birth weight, critically ill neonates who have definite risk attached to transfer to the operating room. No special area is needed in the NICU to perform complication-free surgery, but designing an operating room within the NICU will be ideal. (author)

  16. New highway accident location manual for Missouri.

    Science.gov (United States)

    2013-12-01

    The Missouri HAL manual is used to identify, analyze, and correct high crash locations, and has not been updated since : 1999. This new edition brings the manual up to date, while incorporating the methodology of the national Highway Safety : Manual ...

  17. Probabilistic safety evaluation: Development of procedures with applications on components used in nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Dillstroem, P. [Det Norske Veritas AB, Stockholm (Sweden)

    2000-12-01

    A probabilistic procedure has been developed by SAQ Kontroll AB to calculate two different failure probabilities, P{sub F}: Probability of failure, defect size given by NDT/NDE. Probability of failure, defect not detected by NDT/NDE. Based on the procedure, SAQ Kontroll AB has developed a computer program PROPSE (PRObabilistic Program for Safety Evaluation). Within PROPSE, the following features are implemented: Two different algorithms to calculate the probability of failure are included: Simple Monte Carlo Simulation (MCS), with an error estimate on P{sub F}. First-Order Reliability Method (FORM), with sensitivity factors using the most probable point of failure in a standard normal space. Using these factors, it is possible to rank the parameters within an analysis. Estimation of partial safety factors, given an input target failure probability and characteristic values for fracture toughness, yield strength, tensile strength and defect depth. Extensive validation has been carried out, using the probabilistic computer program STAR6 from Nuclear Electric and the deterministic program SACC from SAQ Kontroll AB. The validation showed that the results from PROPSE were correct, and that the algorithms used in STAR6 were not intended to work for a general problem, when the standard deviation is either 'small' or 'large'. Distributions, to be used in a probabilistic analysis, are discussed. Examples on data to be used are also given.

  18. Probabilistic safety evaluation: Development of procedures with applications on components used in nuclear power plants

    International Nuclear Information System (INIS)

    Dillstroem, P.

    2000-12-01

    A probabilistic procedure has been developed by SAQ Kontroll AB to calculate two different failure probabilities, P F : Probability of failure, defect size given by NDT/NDE. Probability of failure, defect not detected by NDT/NDE. Based on the procedure, SAQ Kontroll AB has developed a computer program PROPSE (PRObabilistic Program for Safety Evaluation). Within PROPSE, the following features are implemented: Two different algorithms to calculate the probability of failure are included: Simple Monte Carlo Simulation (MCS), with an error estimate on P F . First-Order Reliability Method (FORM), with sensitivity factors using the most probable point of failure in a standard normal space. Using these factors, it is possible to rank the parameters within an analysis. Estimation of partial safety factors, given an input target failure probability and characteristic values for fracture toughness, yield strength, tensile strength and defect depth. Extensive validation has been carried out, using the probabilistic computer program STAR6 from Nuclear Electric and the deterministic program SACC from SAQ Kontroll AB. The validation showed that the results from PROPSE were correct, and that the algorithms used in STAR6 were not intended to work for a general problem, when the standard deviation is either 'small' or 'large'. Distributions, to be used in a probabilistic analysis, are discussed. Examples on data to be used are also given

  19. Procedures for initiation, cost-sharing and management of OECD projects in nuclear safety

    International Nuclear Information System (INIS)

    2002-01-01

    The OECD (CSNI) projects aim to produce results relevant for the safe operation of nuclear power plants through international collaborative projects. In general, the projects consist of advanced experimental programmes that are conducted at specialized facilities. At present, the following OECD (CSNI) projects are in operation: - The Halden Project, covering fuel/materials and I and C/Human Factors issues; - The Cabri Project, addressing reactivity transients on high burnup fuels; - The MASCA Project, which deals with in-vessel corium phenomena; - The OLHF Project, dealing with lower head failure mechanisms; - The SETH Project addressing thermal-hydraulics issues, started in 2001; - The MCCI Project on ex-vessel coolability and melt-concrete interaction. There are significant differences among these projects in terms of their motivation, size and scope. The Halden Project and the Cabri Water Loop Project are large undertakings where the host organisations assume full and direct responsibility for the project establishment and administration - as well as for the negotiation with relevant parties on the terms of participation. In the other cases, instead, the NEA secretariat has a more direct responsibility, conferred by the CSNI, in establishing the project technical and financial basis, as well as for its implementation and administration. The objective of this procedure is to provide a common basis for the establishment and management of the OECD projects in the area of nuclear safety. It is a follow-up of a recommendation expressed by the CSNI Bureau during its meeting in October 2001, where the procedures for the establishment and management of the OECD (CSNI) projects in nuclear safety were addressed. While this procedure attempts at defining general guidelines for project initiation, financing and management, one should bear in mind that each project has its own motivation, background and framework. Thus, some degree of flexibility in project structure

  20. PGDP [Paducah Gaseous Diffusion Plant]-UF6 handling, sampling, analysis and associated QC/QA and safety related procedures

    International Nuclear Information System (INIS)

    Harris, R.L.

    1987-01-01

    This document is a compilation of Paducah Gaseous Diffusion Plant procedures on UF 6 handling, sampling, and analysis, along with associated QC/QA and safety related procedures. It was assembled for transmission by the US Department of Energy to the Korean Advanced Energy Institute as a part of the US-Korea technical exchange program

  1. Patient safety improvement programmes for primary care. Review of a Delphi procedure and pilot studies by the LINNEAUS collaboration on patient safety in primary care

    Science.gov (United States)

    Verstappen, Wim; Gaal, Sander; Esmail, Aneez; Wensing, Michel

    2015-01-01

    ABSTRACT Background: To improve patient safety it is necessary to identify the causes of patient safety incidents, devise solutions and measure the (cost-) effectiveness of improvement efforts. Objective: This paper provides a broad overview with practical guidance on how to improve patient safety. Methods: We used modified online Delphi procedures to reach consensus on methods to improve patient safety and to identify important features of patient safety management in primary care. Two pilot studies were carried out to assess the value of prospective risk analysis (PRA), as a means of identifying the causes of a patient safety incident. Results: A range of different methods can be used to improve patient safety but they have to be contextually specific. Practice organization, culture, diagnostic errors and medication safety were found to be important domains for further improvement. Improvement strategies for patient safety could benefit from insights gained from research on implementation of evidence-based practice. Patient involvement and prospective risk analysis are two promising and innovative strategies for improving patient safety in primary care. Conclusion: A range of methods is available to improve patient safety, but there is no ‘magic bullet.’ Besides better use of the available methods, it is important to use new and potentially more effective strategies, such as prospective risk analysis. PMID:26339837

  2. Safety procedures for the MFTF sustaining-neutral-beam power supply

    International Nuclear Information System (INIS)

    Wilson, J.H.

    1981-01-01

    The MFTF SNBPSS comprises a number of sources of potentially hazardous electrical energy in a small physical area. Power is handled at 80 kV dc, 80 A; 70 V dc, 4000 A; 25 V dc, 5500 A; 3 kV dc, 10 A; and 2 kV dc, 10 A. Power for these systems is furnished from two separate 480 V distribution systems and a 13.8 kV distribution system. A defense in depth approach is used; interlocks are provided in the hardware to make it difficult to gain access to an energized circuit, and the operating procedure includes precautions which would protect personnel even if no interlocks were working. The complexity of the system implies a complex operating procedure, and this potential complexity is controlled by presenting the procedure in a modular form using 37 separate checklists for specific operations. The checklists are presented in flowchart form, so contingencies can be handled at the lowest possible level without compromising safety

  3. Developing a Pupil Transportation Manual.

    Science.gov (United States)

    Douglas, Dave

    1987-01-01

    District-level pupil transportation manuals that contain clear, concise information about objectives, policies, and regulations are a must. These manuals should also specify procedures concerning evaluation processes, personnel recruitment and selection, and the driver training program. (MLH)

  4. Probabilistic safety analysis procedures guide, Sections 8-12. Volume 2, Rev. 1

    International Nuclear Information System (INIS)

    McCann, M.; Reed, J.; Ruger, C.; Shiu, K.; Teichmann, T.; Unione, A.; Youngblood, R.

    1985-08-01

    A procedures guide for the performance of probabilistic safety assessment has been prepared for interim use in the Nuclear Regulatory Commission programs. It will be revised as comments are received, and as experience is gained from its use. The probabilistic safety assessment studies performed are intended to produce probabilistic predictive models that can be used and extended by the utilities and by NRC to sharpen the focus of inquiries into a range of issues affecting reactor safety. The first volume of the guide describes the determination of the probability (per year) of core damage resulting from accident initiators internal to the plant (i.e., intrinsic to plant operation) and from loss of off-site electric power. The scope includes human reliability analysis, a determination of the importance of various core damage accident sequences, and an explicit treatment and display of uncertainties for key accident sequences. This second volume deals with the treatment of the so-called external events including seismic disturbances, fires, floods, etc. Ultimately, the guide will be augmented to include the plant-specific analysis of in-plant processes (i.e., containment performance). This guide provides the structure of a probabilistic safety study to be performed, and indicates what products of the study are valuable for regulatory decision making. For internal events, methodology is treated in the guide only to the extent necessary to indicate the range of methods which is acceptable; ample reference is given to alternative methodologies which may be utilized in the performance of the study. For external events, more explicit guidance is given

  5. Probabilistic safety analysis procedures guide. Sections 1-7 and appendices. Volume 1, Revision 1

    International Nuclear Information System (INIS)

    Bari, R.A.; Buslik, A.J.; Cho, N.Z.

    1985-08-01

    A procedures guide for the performance of probabilistic safety assessment has been prepared for interim use in the Nuclear Regulatory Commission programs. It will be revised as comments are received, and as experience is gained from its use. The probabilistic safety assessment studies performed are intended to produce probabilistic predictive models that can be used and extended by the utilities and by NRC to sharpen the focus of inquiries into a range of issues affecting reactor safety. This first volume of the guide describes the determination of the probability (per year) of core damage resulting from accident initiators internal to the plant (i.e., intrinsic to plant operation) and from loss of off-site electric power. The scope includes human reliability analysis, a determination of the importance of various core damage accident sequences, and an explicit treatment and display of uncertainties for key accident sequences. The second volume deals with the treatment of the so-called external events including seismic disturbances, fires, floods, etc. Ultimately, the guide will be augmented to include the plant-specific analysis of in-plant processes (i.e., containment performance). This guide provides the structure of a probabilistic safety study to be performed, and indicates what products of the study are valuable for regulatory decision making. For internal events, methodology is treated in the guide only to the extent necessary to indicate the range of methods which is acceptable; ample reference is given to alternative methodologies which may be utilized in the performance of the study. For external events, more explicit guidance is given

  6. The "SAFARI" Method of Collection Study and Cooperative Acquisition for a Multi-Library Cooperative. A Manual of Procedures.

    Science.gov (United States)

    Sinclair, Dorothy

    This document examines the importance and difficulties in resource sharing and acquisition by libraries and introduces the procedures of the Site Appraisal for Area Resources Inventory (SAFARI) system as a method of comparative evaluation of subject collections among a group of libraries. Resource, or collection, sharing offers specific…

  7. Verification of a primary-to-secondary leaking safety procedure in a nuclear power plant using coloured Petri nets

    International Nuclear Information System (INIS)

    Nemeth, E.; Bartha, T.; Fazekas, Cs.; Hangos, K.M.

    2009-01-01

    This paper deals with formal and simulation-based verification methods of a PRImary-to-SEcondary leaking (abbreviated as PRISE) safety procedure. The PRISE safety procedure controls the draining of the contaminated water in a faulty steam generator when a non-compensable leaking from the primary to the secondary circuit occurs. Because of the discrete nature of the verification, a Coloured Petri Net (CPN) representation is proposed for both the procedure and the plant model. We have proved by using a non-model-based strategy that the PRISE safety procedure is safe, there are no dead markings in the state space, and all transitions are live; being either impartial or fair. Further analysis results have been obtained using a model-based verification approach. We created a simple, low dimensional, nonlinear dynamic model of the primary circuit in a VVER-type pressurized water nuclear power plant for the purpose of the model-based verification. This is in contrast to the widely used safety analysis that requires an accurate detailed model. Our model also describes the relevant safety procedures, as well as all of the major leaking-type faults. We propose a novel method to transform this model to a CPN form by discretization. The composed plant and PRISE safety procedure system has also been analysed by simulation using CPN analysis tools. We found by the model-based analysis-using both single and multiple faults-that the PRISE safety procedure initiates the draining when the PRISE event occurs, and no false alarm will be initiated

  8. Safety and efficacy of rivaroxaban compared with warfarin in patients undergoing peripheral arterial procedures.

    Science.gov (United States)

    Talukdar, Anjan; Wang, S Keisin; Czosnowski, Lauren; Mokraoui, Nassim; Gupta, Alok; Fajardo, Andres; Dalsing, Michael; Motaganahalli, Raghu

    2017-10-01

    Rivaroxaban is a United States Food and Drug Administration-approved oral anticoagulant for venous thromboembolic disease; however, there is no information regarding the safety and its efficacy to support its use in patients after open or endovascular arterial interventions. We report the safety and efficacy of rivaroxaban vs warfarin in patients undergoing peripheral arterial interventions. This single-institution retrospective study analyzed all sequential patients from December 2012 to August 2014 (21 months) who were prescribed rivaroxaban or warfarin after a peripheral arterial procedure. Our study population was then compared using American College of Chest Physicians guidelines with patients then stratified as low, medium, or high risk for bleeding complications. Statistical analyses were performed using the Student t-test and χ 2 test to compare demographics, readmissions because of bleeding, and the need for secondary interventions. Logistic regression models were used for analysis of variables associated with bleeding complications and secondary interventions. The Fisher exact test was used for power analysis. There were 44 patients in the rivaroxaban group and 50 patients in the warfarin group. Differences between demographics and risk factors for bleeding between groups or reintervention rate were not statistically significant (P = .297). However, subgroup evaluation of the safety profile suggests that patients who were aged ≤65 years and on warfarin had an overall higher incidence of major bleeding (P = .020). Patients who were aged >65 years, undergoing open operation, had a significant risk for reintervention (P = .047) when they received rivaroxaban. Real-world experience using rivaroxaban and warfarin in patients after peripheral arterial procedures suggests a comparable safety and efficacy profile. Subgroup analysis of those requiring an open operation demonstrated a decreased bleeding risk when rivaroxaban was used (in those aged <65

  9. Report on nuclear industry quality assurance procedures for safety analysis computer code development and use

    International Nuclear Information System (INIS)

    Sheron, B.W.; Rosztoczy, Z.R.

    1980-08-01

    As a result of a request from Commissioner V. Gilinsky to investigate in detail the causes of an error discovered in a vendor Emergency Core Cooling System (ECCS) computer code in March, 1978, the staff undertook an extensive investigation of the vendor quality assurance practices applied to safety analysis computer code development and use. This investigation included inspections of code development and use practices of the four major Light Water Reactor Nuclear Steam Supply System vendors and a major reload fuel supplier. The conclusion reached by the staff as a result of the investigation is that vendor practices for code development and use are basically sound. A number of areas were identified, however, where improvements to existing vendor procedures should be made. In addition, the investigation also addressed the quality assurance (QA) review and inspection process for computer codes and identified areas for improvement

  10. Pleural procedures and patient safety: a national BTS audit of practice.

    Science.gov (United States)

    Hooper, Clare E; Welham, Sally A; Maskell, Nick A

    2015-02-01

    The BTS pleural procedures audit collected data over a 2-month period in June and July 2011. In contrast with the 2010 audit, which focussed simply on chest drain insertions, data on all pleural aspirations and local anaesthetic thoracoscopy (LAT) was also collected. Ninety hospitals submitted data, covering a patient population of 33 million. Twenty-one per cent of centres ran a specialist pleural disease clinic, 71% had a nominated chest drain safety lead, and 20% had thoracic surgery on site. Additionally, one-third of centres had a physician-led LAT service. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  11. Procedures to relate the NII safety assessment principles for nuclear reactors to risk

    CERN Document Server

    Kelly, G N; Hemming, C R

    1985-01-01

    Within the framework of the Public Inquiry into the proposed pressurised water reactor (PWR) at Sizewell, estimates were made of the levels of individual and societal risk from a PWR designed in a manner which would conform to the safety assessment principles formulated by the Nuclear Installations Inspectorate (NII). The procedures used to derive these levels of risk are described in this report. The opportunity has also been taken to revise the risk estimates made at the time of the Inquiry by taking account of additional data which were not then available, and to provide further quantification of the likely range of uncertainty in the predictions. This re-analysis has led to small changes in the levels of risk previously evaluated, but these are not sufficient to affect the broad conclusions reached before. For a reactor just conforming to the NII safety assessment principles a maximum individual risk of fatal cancer of about 10 sup - sup 6 per year of reactor operation has been estimated; the societal ris...

  12. Application of a statistical thermal design procedure to evaluate the PWR DNBR safety analysis limits

    International Nuclear Information System (INIS)

    Robeyns, J.; Parmentier, F.; Peeters, G.

    2001-01-01

    In the framework of safety analysis for the Belgian nuclear power plants and for the reload compatibility studies, Tractebel Energy Engineering (TEE) has developed, to define a 95/95 DNBR criterion, a statistical thermal design method based on the analytical full statistical approach: the Statistical Thermal Design Procedure (STDP). In that methodology, each DNBR value in the core assemblies is calculated with an adapted CHF (Critical Heat Flux) correlation implemented in the sub-channel code Cobra for core thermal hydraulic analysis. The uncertainties of the correlation are represented by the statistical parameters calculated from an experimental database. The main objective of a sub-channel analysis is to prove that in all class 1 and class 2 situations, the minimum DNBR (Departure from Nucleate Boiling Ratio) remains higher than the Safety Analysis Limit (SAL). The SAL value is calculated from the Statistical Design Limit (SDL) value adjusted with some penalties and deterministic factors. The search of a realistic value for the SDL is the objective of the statistical thermal design methods. In this report, we apply a full statistical approach to define the DNBR criterion or SDL (Statistical Design Limit) with the strict observance of the design criteria defined in the Standard Review Plan. The same statistical approach is used to define the expected number of rods experiencing DNB. (author)

  13. Integration of a browser based operator manual in the system environment of a process computer system

    International Nuclear Information System (INIS)

    Weber, Andreas; Erfle, Robert; Feinkohl, Dirk

    2012-01-01

    The integration of a browser based operator manual in the system environment of a process computer system is an optimization of the operating procedure in the control room and a safety enhancement due to faster and error-free access to the manual contents. Several requirements by the authorities have to be fulfilled: the operating manual has to be available as hard copy, the format has to be true to original, protection against manipulation has to be provided, the manual content of the browser-based version and the hard copy have to identical, and the display presentation has to be consistent with ergonomic principals. The integration of the on-line manual in the surveillance process computer system provides the operator with the relevant comments to the surveillance signal. The described integration of the on-line manual is an optimization of the operator's everyday job with respect to ergonomics and safety (human performance).

  14. Safety Precautions and Operating Procedures in an (A)BSL-4 Laboratory: 2. General Practices.

    Science.gov (United States)

    Mazur, Steven; Holbrook, Michael R; Burdette, Tracey; Joselyn, Nicole; Barr, Jason; Pusl, Daniela; Bollinger, Laura; Coe, Linda; Jahrling, Peter B; Lackemeyer, Matthew G; Wada, Jiro; Kuhn, Jens H; Janosko, Krisztina

    2016-10-03

    Work in a biosafety level 4 (BSL-4) containment laboratory requires time and great attention to detail. The same work that is done in a BSL-2 laboratory with non-high-consequence pathogens will take significantly longer in a BSL-4 setting. This increased time requirement is due to a multitude of factors that are aimed at protecting the researcher from laboratory-acquired infections, the work environment from potential contamination and the local community from possible release of high-consequence pathogens. Inside the laboratory, movement is restricted due to air hoses attached to the mandatory full-body safety suits. In addition, disinfection of every item that is removed from Class II biosafety cabinets (BSCs) is required. Laboratory specialists must be trained in the practices of the BSL-4 laboratory and must show high proficiency in the skills they are performing. The focus of this article is to outline proper procedures and techniques to ensure laboratory biosafety and experimental accuracy using a standard viral plaque assay as an example procedure. In particular, proper techniques to work safely in a BSL-4 environment when performing an experiment will be visually emphasized. These techniques include: setting up a Class II BSC for experiments, proper cleaning of the Class II BSC when finished working, waste management and safe disposal of waste generated inside a BSL-4 laboratory, and the removal of inactivated samples from inside a BSL-4 laboratory to the BSL-2 laboratory.

  15. Procedure for conducting probabilistic safety assessment: level 1 full power internal event analysis

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Won Dae; Lee, Y. H.; Hwang, M. J. [and others

    2003-07-01

    This report provides guidance on conducting a Level I PSA for internal events in NPPs, which is based on the method and procedure that was used in the PSA for the design of Korea Standard Nuclear Plants (KSNPs). Level I PSA is to delineate the accident sequences leading to core damage and to estimate their frequencies. It has been directly used for assessing and modifying the system safety and reliability as a key and base part of PSA. Also, Level I PSA provides insights into design weakness and into ways of preventing core damage, which in most cases is the precursor to accidents leading to major accidents. So Level I PSA has been used as the essential technical bases for risk-informed application in NPPs. The report consists six major procedural steps for Level I PSA; familiarization of plant, initiating event analysis, event tree analysis, system fault tree analysis, reliability data analysis, and accident sequence quantification. The report is intended to assist technical persons performing Level I PSA for NPPs. A particular aim is to promote a standardized framework, terminology and form of documentation for PSAs. On the other hand, this report would be useful for the managers or regulatory persons related to risk-informed regulation, and also for conducting PSA for other industries.

  16. TA-55 change control manual

    International Nuclear Information System (INIS)

    Blum, T.W.; Selvage, R.D.; Courtney, K.H.

    1997-11-01

    This manual is the guide for initiating change at the Plutonium Facility, which handles the processing of plutonium as well as research on plutonium metallurgy. It describes the change and work control processes employed at TA-55 to ensure that all proposed changes are properly identified, reviewed, approved, implemented, tested, and documented so that operations are maintained within the approved safety envelope. All Laboratory groups, their contractors, and subcontractors doing work at TA-55 follow requirements set forth herein. This manual applies to all new and modified processes and experiments inside the TA-55 Plutonium Facility; general plant project (GPP) and line item funded construction projects at TA-55; temporary and permanent changes that directly or indirectly affect structures, systems, or components (SSCs) as described in the safety analysis, including Facility Control System (FCS) software; and major modifications to procedures. This manual does not apply to maintenance performed on process equipment or facility SSCs or the replacement of SSCs or equipment with documented approved equivalents

  17. Processes and Procedures for Application of CFD to Nuclear Reactor Safety Analysis

    International Nuclear Information System (INIS)

    Richard W. Johnson; Richard R. Schultz; Patrick J. Roache; Ismail B. Celik; William D. Pointer; Yassin A. Hassan

    2006-01-01

    Traditionally, nuclear reactor safety analysis has been performed using systems analysis codes such as RELAP5, which was developed at the INL. However, goals established by the Generation IV program, especially the desire to increase efficiency, has lead to an increase in operating temperatures for the reactors. This increase pushes reactor materials to operate towards their upper temperature limits relative to structural integrity. Because there will be some finite variation of the power density in the reactor core, there will be a potential for local hot spots to occur in the reactor vessel. Hence, it has become apparent that detailed analysis will be required to ensure that local ''hot spots'' do not exceed safety limits. It is generally accepted that computational fluid dynamics (CFD) codes are intrinsically capable of simulating fluid dynamics and heat transport locally because they are based on ''first principles''. Indeed, CFD analysis has reached a fairly mature level of development, including the commercial level. However, CFD experts are aware that even though commercial codes are capable of simulating local fluid and thermal physics, great care must be taken in their application to avoid errors caused by such things as inappropriate grid meshing, low-order discretization schemes, lack of iterative convergence and inaccurate time-stepping. Just as important is the choice of a turbulence model for turbulent flow simulation. Turbulence models model the effects of turbulent transport of mass, momentum and energy, but are not necessarily applicable for wide ranges of flow types. Therefore, there is a well-recognized need to establish practices and procedures for the proper application of CFD to simulate flow physics accurately and establish the level of uncertainty of such computations. The present document represents contributions of CFD experts on what the basic practices, procedures and guidelines should be to aid CFD analysts to obtain accurate estimates

  18. A simple intervention to improve patient safety, save time and improve staff experience in the AMU procedure room.

    Science.gov (United States)

    Misselbrook, Gary Peter; Kause, Juliane; Yeoh, Su-Ann

    2016-01-01

    Over the last decade, operating theatres and Intensive Care Units (ICUs) have established systematic methods for performing procedures on patients that have been shown to reduce complications and improve patient safety. Whilst the use of procedure rooms on Acute Medicine Units (AMUs) is highly recommended by patient safety groups and Royal College publications, they are not universally available or appropriately utilised. In this article we discuss a quality improvement project that was undertaken on an AMU at a large university teaching hospital in the United Kingdom, highlighting its successes and challenges.

  19. The safety assessment of OPR-1000 nuclear power plant for station blackout accident applying the combined deterministic and probabilistic procedure

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Dong Gu, E-mail: littlewing@kins.re.kr [Korea Institute of Nuclear Safety, 62 Gwahak-ro, Yuseong-gu, Daejeon 305-338 (Korea, Republic of); Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Chang, Soon Heung [Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 305-701 (Korea, Republic of)

    2014-08-15

    Highlights: • The combined deterministic and probabilistic procedure (CDPP) was proposed for safety assessment of the BDBAs. • The safety assessment of OPR-1000 nuclear power plant for SBO accident is performed by applying the CDPP. • By estimating the offsite power restoration time appropriately, the SBO risk is reevaluated. • It is concluded that the CDPP is applicable to safety assessment of BDBAs without significant erosion of the safety margin. - Abstract: Station blackout (SBO) is a typical beyond design basis accident (BDBA) and significant contributor to overall plant risk. The risk analysis of SBO could be important basis of rulemaking, accident mitigation strategy, etc. Recently, studies on the integrated approach of deterministic and probabilistic method for nuclear safety in nuclear power plants have been done, and among them, the combined deterministic and probabilistic procedure (CDPP) was proposed for safety assessment of the BDBAs. In the CDPP, the conditional exceedance probability obtained by the best estimate plus uncertainty method acts as go-between deterministic and probabilistic safety assessments, resulting in more reliable values of core damage frequency and conditional core damage probability. In this study, the safety assessment of OPR-1000 nuclear power plant for SBO accident was performed by applying the CDPP. It was confirmed that the SBO risk should be reevaluated by eliminating excessive conservatism in existing probabilistic safety assessment to meet the targeted core damage frequency and conditional core damage probability. By estimating the offsite power restoration time appropriately, the SBO risk was reevaluated, and it was finally confirmed that current OPR-1000 system lies in the acceptable risk against the SBO. In addition, it is concluded that the CDPP is applicable to safety assessment of BDBAs in nuclear power plants without significant erosion of the safety margin.

  20. Comparison of the boomerang wire vascular access management system versus manual compression alone during percutaneous diagnostic and interventional cardiovascular procedures: The boomerang™ wire vascular access management trial II.

    Science.gov (United States)

    Goswami, Nilesh J; Smalling, Ronnie G; Sinha, Shantanu; Gammon, Roger S; Ramaiah, Venkatesh G

    2016-01-01

    To evaluate the use of the Boomerang™ Wire as an adjunct to manual compression (MC) in patients requiring diagnostic (Dx) or interventional (Ix) percutaneous procedures. MC remains the standard of care for closure of femoral artery access sites. Adjunctive use of a device to facilitate closure, reduce time to hemostasis (TTH) and ambulation (TTA) without increasing complication rates could reduce costs and hospital resource demands. The Boomerang™ Trial was a prospective, multicenter, randomized, controlled trial comparing use of the Boomerang™ wire, (Cardiva Medical, Sunnyvale, CA) in conjunction with MC versus MC alone to achieve hemostasis in Dx and Ix patients undergoing percutaneous procedures requiring femoral artery access. Endpoints included TTH, TTA, major, and minor access-site related complications. Subjects were randomized 3:1, Boomerang versus MC. No minor or major device-related adverse events were reported. Nondevice related complication rates were 3 (0.9%) in the Boomerang arm (n = 327) and 1 (0.8%) in MC arm (n = 123). Mean TTH for Boomerang vs. MC was 11.2 ± 4.3 vs. 23.2 ± 11 min for Dx (P Boomerang vs. MC was 3.3 ± 3.0 vs. 4.5 ± 2.0 hr (P Boomerang™ use, in conjunction with MC, was associated with low rates of complications and demonstrated that Boomerang™ as an adjunct to MC can significantly decrease TTH and TTA after both Dx and Ix procedures. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

  1. Electrical safety code manual a plan language guide to national electrical code, OSHA and NFPA 70E

    CERN Document Server

    Keller, Kimberley

    2010-01-01

    Safety in any workplace is extremely important. In the case of the electrical industry, safety is critical and the codes and regulations which determine safe practices are both diverse and complicated. Employers, electricians, electrical system designers, inspectors, engineers and architects must comply with safety standards listed in the National Electrical Code, OSHA and NFPA 70E. Unfortunately, the publications which list these safety requirements are written in very technically advanced terms and the average person has an extremely difficult time understanding exactly what they need to

  2. HVAC system operation manual of IMEF

    International Nuclear Information System (INIS)

    Baek, Sang Yeol; Park, Dae Kyu; Ahn, Sang Bok; Ju, Yong Sun.

    1997-06-01

    This manual is operation procedures of the IMEF(Irradiated Material Examination Facility) HVAC(Heating, Ventilation and Air Conditioning) System. General operation procedures and test method of the IMEF HVAC system are described. The manual is as follows; 1. HVAC system operation manual 2. HVAC system management guide 3. HVAC system maintenance manual 4. HVAC system air velocity and flowrate measurement manual 5. HVAC system HEPA filter leak test manual 6. HVAC system charcoal filter leak test manual 7. HVAC system HEPA and charcoal filter exchange manual. (author). 8 tabs

  3. Procedures Manual: A Guide to Uniform Grant and Contract Management Standards and The Common Rule for Uniform Administrative Requirements for Grants and Cooperative Agreements to State and Local Governments.

    Science.gov (United States)

    Conable, Sharon R.

    This manual has been compiled to provide consistent grant application and administrative procedures for state agencies which award grants or contracts to local governments. It provides a conceptual framework of information concerning the reporting, financial, contractual, and auditing requirements for recipients of Texas State Library grants…

  4. Risk and safety of pediatric sedation/anesthesia for procedures outside the operating room.

    Science.gov (United States)

    Cravero, Joseph P

    2009-08-01

    Sedation and anesthesia outside the operating room represents a rapidly growing field of practice that involves a number of different specialty providers including anesthesiology. The literature surrounding this work is found in a variety of journals - many outside anesthesiology. This review is intended to inform readers about the current status of risk and safety involving sedation/anesthesia for tests and minor procedures utilizing a wide range of sources. Two large database studies have helped to define the frequency and nature of adverse events in pediatric sedation/anesthesia practice from a multispecialty perspective. A number of papers describing respiratory and hemodynamic aspects of dexmedetomidine sedation have also been published. Finally, a number of studies relating to training sedation providers, reporting of sedation adverse events, sedation for vulnerable populations, and (in particular) ketamine sedation adverse respiratory events have also come to light. The latest publications continue to document a relatively low risk to pediatric sedation yet also warn us about the potential adverse events in this field. The results help to define competencies required to deliver pediatric sedation and make this practice even safer. Particularly interesting are new jargon and methodologies for defining adverse events and the use of new methods for training sedation providers.

  5. Safety procedures for the electron spectroscopy of actinides at the ALS

    International Nuclear Information System (INIS)

    Shuh, D.K.; Edelstein, N.M.; Bucher, J.J.

    1996-01-01

    This is an addendum to the ALS Experimental Safety Form Renewal for the continuation of actinide microspot experiments on beamlines 7.0. There are several modifications to the previously approved. procedures. There is an increase in the amount of allowable material of the low activity isotopes 238 U, 237 Np, 242 Pu, and 248 Cm. There is also the addition of 99 Tc and the activity isotopes 232 Th and 243 Am to the list of permissible sample materials. All of the materials are alpha-emitters with negligible gamma fields with the exception of 99 Tc which is a beta-emitter. There is a series of new experiments that requires the use of a crystal cleaver in the preparation chamber of the ultraESCA end station. The beamline 7.0 ultraESCA endstation has been suitably modified to permit the safe cleave of YUPd alloy rectangular ingots. AR of the sample materials are solids. The exact nature and composition of the samples are delineated in the sample preparation section that follows. A corresponding Radiological Work Authorization (RWA) must be issued for this work at ALS since the material amounts exceed those in the Low Activity Source (LAS) guidelines in Table I and those in the Values for Exemption of Sealed Source Inventory in Table II. The preliminary date for the next run of these sample materials has been tentatively scheduled in early February 1996 and this will be with the uranium cleave alloys, not the transuranic materials

  6. Road safety audit tools, procedures, and experiences : a literature review and recommendations : research in the framework of the European research project Safety Standards for Road Design and Redesign SAFESTAR, Workpackage 8.

    NARCIS (Netherlands)

    Kooi, R.M. van der

    1999-01-01

    This report describes tools and procedures established in different countries which apply Road Safety Audits (RSA). These RSAs are utilized to identify potential safety problems and they concentrate on safety measures to overcome these problems. This technique is used to detect possible safety

  7. Safety of type and screen method compared to conventional antiglobulin crossmatch procedures for compatibility testing in Indian setting

    Directory of Open Access Journals (Sweden)

    Chaudhary Rajendra

    2011-01-01

    Full Text Available Background: Over the past 30 years, pretransfusion tests have undergone considerable modification. In 1984, AABB recommended that the full cross match could be replaced by an abbreviated cross match in patients with negative antibody screen. However, before implementation of such a policy, issue regarding safety of T & S needs to be evaluated. Objectives: The aim of pretransfusion testing (PTT is to ensure that enough red blood cells (RBCs in the selected red cell components will survive when transfused. Results and Conclusion: We have, therefore in this study; evaluated safety of T & S procedure for PTT in comparison with conventional test tube cross match. The T & S procedure gave a safety of 91.6%. Also, the usefulness of the T & S was shown through the detection of unexpected antibodies in 0.75% (15 out of 2026 of cases.

  8. Modifications of Probabilistic Safety Assessment-1 Nuclear Power Plant Dukovany based upon new version of Emergency Operating Procedures

    International Nuclear Information System (INIS)

    Aldorf, R.

    1997-01-01

    In the frame of 'living Probabilistic Safety Assessment-1 Nuclear Power Plant Dukovany Project' being performed by Nuclear Research Institute Rez during 1997 is planned to reflect on Probabilistic Safety Assessment-1 basis on impact of Emergency Response Guidelines (as one particular event from the list of other modifications) on Plant Safety. Following highlights help to orient the reader in main general aspects, findings and issues of the work that currently continues on. Older results of Probabilistic Safety Assessment-1 Nuclear Power Plant Dukovany have revealed that human behaviour during accident progression scenarios represent one of the most important aspects in plant safety. Current effort of Nuclear Power Plants Dukovany (Czech Republic) and Bohunice (Slovak Republic) is focussed on development of qualitatively new symptom-based Emergency Operating Procedures called Emergency Response Guidelines Supplier - Westinghouse Energy Systems Europe, Brussels works in cooperation with teams of specialist from both Nuclear Power Plants. In the frame of 'living Probabilistic Safety Assessment-1 Nuclear Power Plant Dukovany Project' being performed by Nuclear Research Institute Rez during 1997 is planned to prove on Probabilistic Safety Assessment -1 basis an expected - positive impact of Emergency Response Guidelines on Plant Safety, Since this contract is currently still in progress, it is possible to release only preliminary conclusions and observations. Emergency Response Guidelines compare to original Emergency Operating Procedures substantially reduce uncertainty of general human behaviour during plant response to an accident process. It is possible to conclude that from the current scope Probabilistic Safety Assessment Dukovany point of view (until core damage), Emergency Response Guidelines represent adequately wide basis for mitigating any initiating event

  9. Databases on safety issues for WWER and RBMK reactors. Users' manual. A publication of the extrabudgetary programme on the safety of WWER and RBMK nuclear power plants

    International Nuclear Information System (INIS)

    1996-04-01

    At the beginning of the IAEA Extrabudgetary Programme on the safety of WWER reactors a great number of findings and recommendations (safety items) were collected as a result of design review and safety review missions of the WWER-440/230 type reactors. On the basis of these findings a technical database containing more than 1300 records was established to support the consolidation of the information obtained and to help in identification of safety issues. After the scope of the WWER extrabudgetary programme was extended similar data sets were prepared for the WWER-440/213, WWER-1000 and RBMK nuclear power plants. This publication describes the structure of the databases on safety issues of WWER and RBMK NPPs, the information sources used in the databases and interrogation capabilities for users to obtain the necessary information. 14 refs, 9 figs, 5 tabs

  10. Fuel Element Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Burley, H.H. [ed.

    1956-08-01

    It is the purpose of the Fuel Element Technical Manual to Provide a single document describing the fabrication processes used in the manufacture of the fuel element as well as the technical bases for these processes. The manual will be instrumental in the indoctrination of personnel new to the field and will provide a single data reference for all personnel involved in the design or manufacture of the fuel element. The material contained in this manual was assembled by members of the Engineering Department and the Manufacturing Department at the Hanford Atomic Products Operation between the dates October, 1955 and June, 1956. Arrangement of the manual. The manual is divided into six parts: Part I--introduction; Part II--technical bases; Part III--process; Part IV--plant and equipment; Part V--process control and improvement; and VI--safety.

  11. ABCC publication manual

    Energy Technology Data Exchange (ETDEWEB)

    1959-01-01

    The reporting policy of the Atomic Bomb Casualty Commission is described in detail in this manual. Specific topics covered are: research project register; research publication policy; USA publication procedures; Japan publication procedures, report preparation instructions; and a glossary of institutions terms, phrases, and symbols. 15 figures. (DMC)

  12. Fire Protection Program Manual

    Energy Technology Data Exchange (ETDEWEB)

    Sharry, J A

    2012-05-18

    This manual documents the Lawrence Livermore National Laboratory (LLNL) Fire Protection Program. Department of Energy (DOE) Orders 420.1B, Facility Safety, requires LLNL to have a comprehensive and effective fire protection program that protects LLNL personnel and property, the public and the environment. The manual provides LLNL and its facilities with general information and guidance for meeting DOE 420.1B requirements. The recommended readers for this manual are: fire protection officers, fire protection engineers, fire fighters, facility managers, directorage assurance managers, facility coordinators, and ES and H team members.

  13. Knowledge of Health Volunteers in the Damavand District on Food Safety: A Study Based on the World Health Organization Manual

    Directory of Open Access Journals (Sweden)

    M Ghfari

    2016-09-01

    Full Text Available Introduction: Food borne illnesses are usually infectious or toxic in nature and caused by bacteria, viruses, parasites or chemical substances entering the body through contaminated food or water. Unsafe food causes more than 200 diseases - ranging from diarrhea to cancers. Food safety is a public health priority. The aim of present study was determine level of health communicators' knowledge about food safety in Damavand city that was performed according to the World Health Organization guide. Methods: This study is a descriptive analysis of the target a group of health Volunteers in Damavand depended to Shahid Beheshti University of Medical Sciences. 109 persons were enrolled with s awareness, scarification and consent of the census. Tools for data collection was a questionnaire consisting of 13 questions on demographic characteristics and 24 questions about food safety according to WHO’s guide. Data was analyzed with SPSS-18 software and statistical analysis includes one-way ANOVA, t-test and spearman correlation. Results: The mean age of participant was 44.75 ± 9.98 years. Average score of awareness of food safety was 35.87 ±6.22 and for awareness was 77 (71%. No significant relationships was observed between of awareness and marital status, age, education, occupation and education of wife was not significant relationships (p>0/05. Conclusion: In some safety food items the level of knowledge in some safety food items was good, in other one, such as food storage, transmission of microbes, cooking temperature for meat there was low awareness. In this respect, information, education programs to raise awareness of the health status for health volunteers is recommended

  14. Propofol for procedural sedation and analgesia reduced dedicated emergency nursing time while maintaining safety in a community emergency department.

    Science.gov (United States)

    Reynolds, Joshua C; Abraham, Michael K; Barrueto, Fermin F; Lemkin, Daniel L; Hirshon, Jon M

    2013-09-01

    Procedural sedation and analgesia is a core competency in emergency medicine. Propofol is replacing midazolam in many emergency departments. Barriers to performing procedural sedation include resource utilization. We hypothesized that emergency nursing time is shorter with propofol than midazolam, without increasing complications. Retrospective analysis of a procedural sedation registry for two community emergency departments with combined census of 100,000 patients/year. Demographics, procedure, and ASA physical classification status of adult patients receiving procedural sedation between 2007-2010 with midazolam or propofol were analyzed. Primary outcome was dedicated emergency nursing time. Secondary outcomes were procedural success, ED length of stay, and complication rate. Comparative statistics were performed with Mann-Whitney, Kruskal-Wallis, chi-square, or Fisher's exact test. Linear regression was performed with log-transformed procedural sedation time to define predictors. Of 328 procedural sedation and analgesia, 316 met inclusion criteria, of which 60 received midazolam and 256 propofol. Sex distribution varied between groups (midazolam 3% male; propofol 55% male; P = 0.04). Age, procedure, and ASA status were not significantly different. Propofol had shorter procedural sedation time (propofol 32.5 ± 24.2 minutes; midazolam 78.7 ± 51.5 minutes; P differences between complication rates (propofol 14%; midazolam 13%; P = 0.88) or emergency department length of stay (propofol 262.5 ± 132.8 minutes; midazolam 288.6 ± 130.6 minutes; P = 0.09). Use of propofol resulted in shorter emergency nursing time and higher procedural success rate than midazolam with a comparable safety profile. Copyright © 2013 Emergency Nurses Association. Published by Mosby, Inc. All rights reserved.

  15. The procedures used to review safety analysis reports for packagings submitted to the US Department of Energy for certification

    International Nuclear Information System (INIS)

    Popper, G.F.; Raske, D.T.; Turula, P.

    1988-01-01

    This paper presents an overview of the procedures used at the Argonne National Laboratory (ANL) to review Safety Analysis Reports for Packagings (SARPs) submitted to the US Department of Energy (DOE) for issuance of a Certificate of Compliance. Prior to certification and shipment of a packaging for the transport of radioactive materials, a SARP must be prepared describing the design, contents, analyses, testing, and safety features of the packaging. The SARP must be reviewed to ensure that the specific packaging meets all DOE orders and federal regulations for safe transport. The ANL SARP review group provides an independent review and evaluation function for the DOE to ensure that the packaging meets all the prescribed requirements. This review involves many disciplines and includes evaluating the general information, drawings, construction details, operating procedures, maintenance and test programs, and the quality assurance plan for compliance with requirements. 14 refs., 6 figs

  16. 78 FR 4985 - Uniform Procedures for State Highway Safety Grant Programs

    Science.gov (United States)

    2013-01-23

    ...) that were tied to the agency's child restraint performance standards (FMVSS 213). Thus, under today's... consolidates into one rule a number of old regulations (State Highway Safety Agency, Political Subdivision... Belt Performance Grants (formerly codified at 23 U.S.C. 406) and Child Safety and Child Booster Seat...

  17. Users manual for Aerospace Nuclear Safety Program six-degree-of-freedom reentry simulation (TMAGRA6C)

    International Nuclear Information System (INIS)

    Sharbaugh, R.C.

    1990-02-01

    This report documents the updated six-degree-of-freedom reentry simulation TMAGRA6C used in the Aerospace Nuclear Safety Program, ANSP. The simulation provides for the inclusion of the effects of ablation on the aerodynamic stability and drag of reentry bodies, specifically the General Purpose Heat Source, GPHS. The existing six-degree-of-freedom reentry body simulations (TMAGRA6A and TMAGRA6B) used in the JHU/APL Nuclear Safety Program do not include aerodynamic effects resulting from geometric changes to the configuration due to ablation from reentry flights. A wind tunnel test was conducted in 1989 to obtain the effects of ablation on the hypersonic aerodynamics of the GPHS module. The analyzed data were used to form data sets which are included herein in tabular form. These are used as incremental aerodynamic inputs in the new TMAGRA6C six-degree-of-freedom reentry simulation. 20 refs., 13 figs., 2 tabs

  18. Operating manual for the Tower Shielding Facility

    International Nuclear Information System (INIS)

    1985-12-01

    This manual provides information necessary to operate and perform maintenance on the reactor systems and all equipment or systems which can affect their operation or the safety of personnel at the Tower Shielding Facility. The first four chapters consist of introductory and descriptive material of benefit to personnel in training, the qualifications required for training, the responsibilities of the personnel in the organization, and the procedures for reviewing proposed experiments. Chapter 8, Emergency Procedures, is also a necessary part of the indoctrination of personnel. The procedures for operation of the Tower Shielding Reactor (TSR-II), its water cooling system, and the main tower hoists are outlined in Chapters 5, 6, and 7. The Technical Specification surveillance requirements for the TSR-II are summarized in Chapter 9. The maintenance and calibration schedule is spelled out in Chapter 10. The procedures for assembly and disassembly of the TSR-II are outlined in Chapter 11

  19. An approach toward estimating the safety significance of normal and abnormal operating procedures in nuclear power plants

    International Nuclear Information System (INIS)

    Grant, T.F.; Harris, M.S.

    1989-01-01

    The Nuclear Regulatory Commission's TMI Action Plan calls for a long-term plan to upgrade operating procedures in nuclear power plants. The scope of Generic Issue Human Factors 4.4, which stems from this requirement, includes the recommendation of improvements in nuclear power plant normal and abnormal operating procedures (NOPs and AOPs) and the implementation of appropriate regulatory action. This paper will describe the objectives, methodologies, and results of a Battelle-conducted value impact assessment to determine the costs and benefits of having the NRC implement regulatory action that would specify requirements for the preparation of acceptable NOPs and AOPs by the Commission's nuclear power plant licensees. The results of this value impact assessment are expressed in terms of ten cost/benefit attributes that can be affected by the NRC regulatory action. Five of these attributes require the calculation of change in public risk that could be expected to result from the action which, in this case, required determining the safety significance of NOPs and AOPs. In order to estimate this safety significance, a multi-step methodology was created that relies on an existing Probabilistic Risk Assessment (PRA) to provide a quantitative framework for modeling the role of operating procedures. The purpose of this methodology is to determine what impact the improvement of NOPs and AOPs would have on public health and safety

  20. Development in France of nuclear safety technical regulations and standards used in the licensing procedure

    International Nuclear Information System (INIS)

    Lebouleux, P.

    1983-04-01

    Initially, the Commissariat a l'Energie Atomique was the overall structure which encompassed all nuclear activities in France, including those connected with radiological protection and nuclear safety. As other partners appeared, the Authorities have laid down national regulations relative to nuclear installations since 1963. These regulations more particularly provide for the addition of prescriptions with which the applicant must comply to obtain the necessary licenses and the establishment of General Technical Regulations pertaining to nuclear safety. The technical regulation related to nuclear safety in France is made of a set of regulation texts, of a different nature, that define the requirements for the construction, commissioning and operation of nuclear facilities. Simultaneously, the safety authorities (Service Central de Surete des Installations Nucleaires: SCSIN) issue recommendations or guides which are not strictly speaking regulations in the juridical sense; they are called ''Regles Fondamentales de Surete'' (RFS). The RFS set up and detail the conditions, the respect of which is deemed to be complying with the French regulation practice, for the subject to which they relate. Their purpose is to make known rules judged acceptable by safety authorities, thus making the safety review easier. A RFS, or a letter, can also give the result of the examination of the constructor and operator codes (RCC) by safety authorities

  1. Nuclear material operations manual

    International Nuclear Information System (INIS)

    Tyler, R.P.

    1981-02-01

    This manual provides a concise and comprehensive documentation of the operating procedures currently practiced at Sandia National Laboratories with regard to the management, control, and accountability of nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations-management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of playscripts in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

  2. Nuclear material operations manuals

    International Nuclear Information System (INIS)

    Tyler, R.P.

    1979-06-01

    This manual is intended to provide a concise and comprehensive documentation of the operating procedures currently practiced at Sandia Laboratories with regard to the management, control, and accountability of radioactive and nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations-management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of playscripts in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

  3. Nuclear material operations manual

    International Nuclear Information System (INIS)

    Tyler, R.P.; Gassman, L.D.

    1978-04-01

    This manual is intended to provide a concise and comprehensive documentation of the operating procedures currently practiced at Sandia Laboratories with regard to the management, control, and accountability of radioactive and nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations--management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of ''play-scripts'' in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

  4. Southeast Regional Implementation Manual for Requirements and Procedures for Evaluation of the Ocean Disposal of Dredged Material in Southeastern U.S. Atlantic and Gulf Coast Waters

    Science.gov (United States)

    This Regional Implementation Manual was prepared by EPA Region 4 to provide guidance for applicants proposing open-water disposal of dredged material in southeastern U.S. coastal waters of the Atlantic Ocean and the Gulf of Mexico.

  5. Assessment of the safety of injection practices and injection-related procedures in family health units and centers in Alexandria.

    Science.gov (United States)

    Elhoseeny, Taghareed A; Mourad, Juidan K

    2014-08-01

    The Safe Injection Global Network (SIGN) developed an intervention strategy for reducing overuse of injections and promoting the administration of safe injections. Tool C--Revised is designed to assess the safety of the most common procedures that puncture the skin within health services. The aim of the study was to assess injection safety within the primary healthcare facilities in Alexandria using Tool C--Revised. A total of 45 family health units and centers in Alexandria were selected by proportional allocation from the eight regions of Alexandria. The Tool C--Revised of the WHO was used for observation of the entire facility, injection practices and injection-related procedures, and sterilization practices. Interview of different health providers and immediate supervisor of injections was carried out. Indicators that reflect risk included: deficiency of alcohol-based hand rub for cleansing hands (13.3%), compliance with hand wash before preparing a procedure (56.9% before injection practices, 61.3% before phlebotomy, and 67.6% before lancet puncture), and wearing a new pair of gloves before new procedures (48.6% before injection practices, 9.7% for phlebotomy, 11.8% for lancet puncture, and 80% for both intravenous injections and infusions). Enough disposable equipment in all facilities for at least 2 weeks dependent on the statement of the average numbers of procedures per week was shown. Only 38% of the providers had received training regarding injection safety in the last 2 years and 62.5% had completed their three doses of hepatitis B vaccine. Only 42.2% of staffs who handled healthcare waste had access to heavy gloves. Indicators related to injection and injection-related practices that reflect risk to patients include deficiency of alcohol-based hand rub tools, nonadherence to hand hygiene before preparing an injection, and inadequate adherence to using a clean barrier when opening a glass ampule and use of gloves. Indicators that may reflect risk to

  6. Virtual Road Safety Audits: Recommended Procedures for Using Driving Simulation and Technology to Expand Existing Practices

    Science.gov (United States)

    2018-02-02

    One approach that has been proposed to address the limitations of the current reactive safetymonitoring approaches is the use of road safety audits (RSAs). As part of an RSA, the existing or expected characteristics and traffic conditions of a locati...

  7. Procedure for the determination of gap and base ground surface configurations beneath the bottom plate of storage tanks using neutron gauging inspection techniques : including radiation safety procedure and emergency procedure

    International Nuclear Information System (INIS)

    Jaafar Abdullah

    1993-01-01

    The procedure is intended for the neutron gauging inspection of gap between the bottom plate and the foundation of bulk storage tanks, which potentially exhibit uneven sinking of the bottom plate and the foundation. Its describes the requirements for the performance of neutron back scattered inspection techniques (or radiometric non-destructive evaluation techniques), using an isotopic neutron source associated with neutron detecting systems, to detect and size the gap between the bottom plate and the foundations as well as to quantify the presence of hydrogenous materials (e.g. oil or water) underneath the bottom plate. This procedure is not only outline the requirements for the neutron gauging inspection, but also describes the requirements which shall be taken into account in formulating the radiation safety and emergency procedures for the neutron gauging inspection works

  8. Culture of safety. Indicators of culture of safety. Stage of culture of safety. Optimization of radiating protection. Principle of precaution. Principle ALARA. Procedure ALARA

    International Nuclear Information System (INIS)

    Mursa, E.

    2006-01-01

    Object of research: is the theory and practice of optimization of radiating protection according to recommendations of the international organizations, realization of principle ALARA and maintenance of culture of safety (SC) on the nuclear power plant. The purpose of work - to consider the general aspects of realization of principle ALARA, conceptual bases of culture of safety, as principle of management, and practice of their introduction on the nuclear power plant. The work has the experts' report character in which the following questions are presented: The recommendations materials of the IAEA and other international organizations have been assembled, systematized and analyzed. The definitions, characteristics and universal SC features, and also indicators as a problem of parameters and quantitative SC measurements are described in details advanced. The ALARA principles - principle of precaution; not acceptance of zero risk; choice of a principle ALARA; model of acceptable radiation risk are described. The methodology of an estimation of culture of safety level and practical realization of the ALARA principle in separate organization is shown on a practical example. The SC general estimation at a national level in Republic of Moldova have been done. Taking into consideration that now Safety Culture politics are introduced only in relation to APS, in this paper the attempt of application of Safety Culture methodology to Radiological Objects have been made (Oncological Institute of the Republic of Moldova and Special Objects No.5101 and 5102 for a long time Storage of the Radioactive Waste). (authors)

  9. Safety analysis report 231-Z Building

    Energy Technology Data Exchange (ETDEWEB)

    Powers, C.S.

    1989-03-01

    This report provides an intensive review of the nuclear safety of the operation of the 231-Z Building. For background information complete descriptions of the floor plan, building services, alarm systems, and glove box systems are included in this report. In addition, references are included to The Plutonium Laboratory Radiation Work Procedures, Safety Guides, 231-Z Operating Procedures Manual and Nuclear Materials accountability Procedures. Engineered and administrative features contribute to the overall safety of personnel, the building, and environs. The consequences of credible incidents were considered and are discussed.

  10. Manual on industrial radiography

    International Nuclear Information System (INIS)

    1981-08-01

    This manual is intended as a source of educational material to personnel seeking certification as industrial radiographers, and as a guide and reference text for educational organizations that are providng courses in industrial radiography. It covers the basic principles of x-ray and gamma radiation, radiation safety, films and film processing, welding, casting and forging, aircraft structures and components, radiographic techniques, and records

  11. Methodology for assessing the safety of Hydrogen Systems: HyRAM 1.1 technical reference manual

    Energy Technology Data Exchange (ETDEWEB)

    Groth, Katrina; Hecht, Ethan; Reynolds, John Thomas; Blaylock, Myra L.; Erin E. Carrier

    2017-03-01

    The HyRAM software toolkit provides a basis for conducting quantitative risk assessment and consequence modeling for hydrogen infrastructure and transportation systems. HyRAM is designed to facilitate the use of state-of-the-art science and engineering models to conduct robust, repeatable assessments of hydrogen safety, hazards, and risk. HyRAM is envisioned as a unifying platform combining validated, analytical models of hydrogen behavior, a stan- dardized, transparent QRA approach, and engineering models and generic data for hydrogen installations. HyRAM is being developed at Sandia National Laboratories for the U. S. De- partment of Energy to increase access to technical data about hydrogen safety and to enable the use of that data to support development and revision of national and international codes and standards. This document provides a description of the methodology and models contained in the HyRAM version 1.1. HyRAM 1.1 includes generic probabilities for hydrogen equipment fail- ures, probabilistic models for the impact of heat flux on humans and structures, and computa- tionally and experimentally validated analytical and first order models of hydrogen release and flame physics. HyRAM 1.1 integrates deterministic and probabilistic models for quantifying accident scenarios, predicting physical effects, and characterizing hydrogen hazards (thermal effects from jet fires, overpressure effects from deflagrations), and assessing impact on people and structures. HyRAM is a prototype software in active development and thus the models and data may change. This report will be updated at appropriate developmental intervals.

  12. OIE philosophy, policy and procedures for the development of food safety standards.

    Science.gov (United States)

    Droppers, W F G L

    2006-08-01

    Food safety was identified as a high priority area in the 2001-2005 World Organisation for Animal Health (OIE) Strategic Plan. Member Countries of the OIE considered that the organisation should be more active in issues of public health and consumer protection and that this should include more involvement in the area of diseases or pathogens transmissible through food, whether or not animals are affected by such diseases or pathogens. A permanent Working Group on Animal Production Food Safety was established in 2002 to coordinate the OIE's activities in food safety. The Working Group was requested to focus on food safety measures applicable at farm level and to monitor the ongoing cooperation between the OIE and Codex Alimentarius. More emphasis is now placed on the public health aspects of a disease when OIE standards are developed or revised. For example, the revised chapter on bovine tuberculosis in the Terrestrial Animal Health Code includes food safety recommendations for meat and meat products and for milk and milk products. The revised chapter was approved by the OIE International Committee of Member Countries at their 73rd General Session in May 2005. More chapters will follow, beginning with a chapter addressing bovine brucellosis.

  13. Energetic soft-tissue treatment technologies: an overview of procedural fundamentals and safety factors

    NARCIS (Netherlands)

    van de Berg, N. J.; van den Dobbelsteen, J. J.; Jansen, F. W.; Grimbergen, C. A.; Dankelman, J.

    2013-01-01

    Energy administered during soft-tissue treatments may cauterize, coagulate, seal, or otherwise affect underlying structures. A general overview of the functionality, procedural outcomes, and associated risks of these treatments, however, is not yet generally available. In addition, literature is

  14. Patient safety during procedural sedation using capnography monitoring : A systematic review and meta-analysis

    NARCIS (Netherlands)

    Saunders, Rhodri; Struys, Michel M. R. F.; Pollock, Richard F.; Mestek, Michael; Lightdale, Jenifer R.

    2017-01-01

    Objective: To evaluate the effect of capnography monitoring on sedation-related adverse events during procedural sedation and analgesia (PSA) administered for ambulatory surgery relative to visual assessment and pulse oximetry alone. Design and setting: Systematic literature review and random

  15. Safety training and safe operating procedures written for PBFA [Particle Beam Fusion Accelerator] II and applicable to other pulsed power facilities

    International Nuclear Information System (INIS)

    Donovan, G.L.; Goldstein, S.A.

    1986-12-01

    To ensure that work in advancing pulsed power technology is performed with an acceptably low risk, pulsed power research facilities at Sandia National Laboratories must satisfy general safety guidelines established by the Department of Energy, policies and formats of the Environment, Safety, and Health (ES and H) Department, and detailed procedures formulated by the Pulsed Power Sciences Directorate. The approach to safety training and to writing safe operating procedures, and the procedures presented here are specific to the Particle Beam Fusion Accelerator II (PBFA II) Facility but are applicable as guidelines to other research and development facilities which have similar hazards

  16. Safety training and safe operating procedures written for PBFA (Particle Beam Fusion Accelerator) II and applicable to other pulsed power facilities

    Energy Technology Data Exchange (ETDEWEB)

    Donovan, G.L.; Goldstein, S.A.

    1986-12-01

    To ensure that work in advancing pulsed power technology is performed with an acceptably low risk, pulsed power research facilities at Sandia National Laboratories must satisfy general safety guidelines established by the Department of Energy, policies and formats of the Environment, Safety, and Health (ES and H) Department, and detailed procedures formulated by the Pulsed Power Sciences Directorate. The approach to safety training and to writing safe operating procedures, and the procedures presented here are specific to the Particle Beam Fusion Accelerator II (PBFA II) Facility but are applicable as guidelines to other research and development facilities which have similar hazards.

  17. Operational limits and conditions and operating procedures for research reactors. Safety guide

    International Nuclear Information System (INIS)

    2008-01-01

    This publication provides practical guidance on all important aspects of developing, formulating and presenting the operational limits and conditions as well as the operating procedures for research reactors. It covers the concept of operational limits and conditions, their content, and the responsibilities of the operating organization with respect to their establishment, modification, documentation and compliance. The guidance also covers the training of operating personnel on performing periodic testing, established by the operational limits and conditions, and operating procedures

  18. Safety procedures used during the manufacturing of amorphous silicon solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Dickson, C R

    1987-01-01

    The Solarex Thin Film Division is a leader in the manufacturing of amorphous-silicon products for sale in domestic and foreign markets. Similarly, Solarex assumes a leadership role in recognizing the importance of safety in a manufacturing environment. Although many of the safety issues are similar to those in the semiconductor industry, this paper presents topics specific to amorphous silicon technology and the manufacturing ,f amorphous-silicon products. These topics are deposition of conducting transparent oxides (CTOs), amorphous silicon deposition, laser scribing, processing chemicals, fire prevention and administrative responsibilities.

  19. Manual Therapy

    OpenAIRE

    Hakgüder, Aral; Kokino, Siranuş

    2002-01-01

    Manual therapy has been used in the treatment of pain and dysfunction of spinal and peripheral joints for more than a hundred years. Manual medicine includes manipulation, mobilization, and postisometric relaxation techniques. The aim of manual therapy is to enhance restricted movement caused by blockage of joints keeping postural balance, restore function and maintain optimal body mechanics. Anatomic, biomechanical, and neurophysiological evaluations of the leucomotor system is essential for...

  20. Long Term Resource Monitoring Program procedures: fish monitoring

    Science.gov (United States)

    Ratcliff, Eric N.; Glittinger, Eric J.; O'Hara, T. Matt; Ickes, Brian S.

    2014-01-01

    This manual constitutes the second revision of the U.S. Army Corps of Engineers’ Upper Mississippi River Restoration-Environmental Management Program (UMRR-EMP) Long Term Resource Monitoring Program (LTRMP) element Fish Procedures Manual. The original (1988) manual merged and expanded on ideas and recommendations related to Upper Mississippi River fish sampling presented in several early documents. The first revision to the manual was made in 1995 reflecting important protocol changes, such as the adoption of a stratified random sampling design. The 1995 procedures manual has been an important document through the years and has been cited in many reports and scientific manuscripts. The resulting data collected by the LTRMP fish component represent the largest dataset on fish within the Upper Mississippi River System (UMRS) with more than 44,000 collections of approximately 5.7 million fish. The goal of this revision of the procedures manual is to document changes in LTRMP fish sampling procedures since 1995. Refinements to sampling methods become necessary as monitoring programs mature. Possible refinements are identified through field experiences (e.g., sampling techniques and safety protocols), data analysis (e.g., planned and studied gear efficiencies and reallocations of effort), and technological advances (e.g., electronic data entry). Other changes may be required because of financial necessity (i.e., unplanned effort reductions). This version of the LTRMP fish monitoring manual describes the most current (2014) procedures of the LTRMP fish component.

  1. Operating manual for the critical experiments facility

    International Nuclear Information System (INIS)

    1986-01-01

    The operation of the Critical Experiments Facility (CEF) requires careful attention to procedures in order that all safety precautions are observed. Since an accident could release large amounts of radioactivity, careful operation and strict enforcement of procedures are necessary. To provide for safe operation, detailed procedures have been written for all phases of the operation of this facility. The CEF operating procedures are not to be construed to constitute a part ofthe Technical Specifications. In the event of any discrepancy between the information given herein and the Technical Specifications, limits set forth in the Technical Specifications apply. All normal and most emergency operation conditions are covered by procedures presented in this manual. These procedures are designed to be followed by the operating personnel. Strict adherence to these procedures is expected for the following reasons. (1) To provide a standard, safe method of performing all operations, the procedures were written by reactor engineers experienced in supervising the operation of reactors and were reviewed by an organization with over 30 years of reactor operating experience. (2) To have an up-to-date description of operating techniques available at all times for reference and review, it is necessary that the procedures be written

  2. Operating manual for the critical experiments facility

    Energy Technology Data Exchange (ETDEWEB)

    1986-01-01

    The operation of the Critical Experiments Facility (CEF) requires careful attention to procedures in order that all safety precautions are observed. Since an accident could release large amounts of radioactivity, careful operation and strict enforcement of procedures are necessary. To provide for safe operation, detailed procedures have been written for all phases of the operation of this facility. The CEF operating procedures are not to be construed to constitute a part ofthe Technical Specifications. In the event of any discrepancy between the information given herein and the Technical Specifications, limits set forth in the Technical Specifications apply. All normal and most emergency operation conditions are covered by procedures presented in this manual. These procedures are designed to be followed by the operating personnel. Strict adherence to these procedures is expected for the following reasons. (1) To provide a standard, safe method of performing all operations, the procedures were written by reactor engineers experienced in supervising the operation of reactors and were reviewed by an organization with over 30 years of reactor operating experience. (2) To have an up-to-date description of operating techniques available at all times for reference and review, it is necessary that the procedures be written.

  3. Operating Manual of Helium Refrigerator (Rev. 2)

    Energy Technology Data Exchange (ETDEWEB)

    Song, K.M.; Son, S.H.; Kim, K.S.; Lee, S.K.; Kim, M.S. [Korea Electric Power Research Institute, Taejon (Korea)

    2002-07-01

    A helium refrigerator was installed as a supplier of 20K cold helium to the cryogenic distillation system of WTRF pilot plant. The operating procedures of the helium refrigerator, helium compressor and auxiliary apparatus are described for the safety and efficient operation in this manual. The function of the helium refrigerator is to remove the impurities from the compressed helium of about 250psig, to cool down the helium from ambient temperature to 20K through the heat exchanger and expansion engine and to transfer the cold helium to the cryogenic distillation system. For the smoothly operation of helium refrigerator, the preparation, the start-up, the cool-down and the shut-down of the helium refrigerator are described in this operating manual. (author). 3 refs., 14 tabs.

  4. 78 FR 53497 - Uniform Procedures for State Highway Safety Grant Programs

    Science.gov (United States)

    2013-08-29

    ...., Eastern Time, Monday through Friday, except Federal holidays. Whichever way you submit your comments... holidays. FOR FURTHER INFORMATION CONTACT: Barbara Sauers, Program Manager, National Highway Traffic Safety... Columbia, Puerto Rico, U.S. Virgin Islands, Guam, American Samoa, the Commonwealth of the Northern Mariana...

  5. Coordination and safety procedures for mail delivery on roadways without shoulders : technical report.

    Science.gov (United States)

    2009-08-01

    This research utilized interviews, focus groups, and surveys of U.S. Postal Service (USPS) and Texas Department of Transportation (TxDOT) employees to determine safety and coordination issues related to mail delivery on rural, two-lane highways witho...

  6. Safety Precautions and Operating Procedures in an (A)BSL-4 Laboratory: 1. Biosafety Level 4 Suit Laboratory Suite Entry and Exit Procedures.

    Science.gov (United States)

    Janosko, Krisztina; Holbrook, Michael R; Adams, Ricky; Barr, Jason; Bollinger, Laura; Newton, Je T'aime; Ntiforo, Corrie; Coe, Linda; Wada, Jiro; Pusl, Daniela; Jahrling, Peter B; Kuhn, Jens H; Lackemeyer, Matthew G

    2016-10-03

    Biosafety level 4 (BSL-4) suit laboratories are specifically designed to study high-consequence pathogens for which neither infection prophylaxes nor treatment options exist. The hallmarks of these laboratories are: custom-designed airtight doors, dedicated supply and exhaust airflow systems, a negative-pressure environment, and mandatory use of positive-pressure ("space") suits. The risk for laboratory specialists working with highly pathogenic agents is minimized through rigorous training and adherence to stringent safety protocols and standard operating procedures. Researchers perform the majority of their work in BSL-2 laboratories and switch to BSL-4 suit laboratories when work with a high-consequence pathogen is required. Collaborators and scientists considering BSL-4 projects should be aware of the challenges associated with BSL-4 research both in terms of experimental technical limitations in BSL-4 laboratory space and the increased duration of such experiments. Tasks such as entering and exiting the BSL-4 suit laboratories are considerably more complex and time-consuming compared to BSL-2 and BSL-3 laboratories. The focus of this particular article is to address basic biosafety concerns and describe the entrance and exit procedures for the BSL-4 laboratory at the NIH/NIAID Integrated Research Facility at Fort Detrick. Such procedures include checking external systems that support the BSL-4 laboratory, and inspecting and donning positive-pressure suits, entering the laboratory, moving through air pressure-resistant doors, and connecting to air-supply hoses. We will also discuss moving within and exiting the BSL-4 suit laboratories, including using the chemical shower and removing and storing positive-pressure suits.

  7. Recommended safety procedures for the selection and use of demonstration-type gas discharge devices in schools

    International Nuclear Information System (INIS)

    1979-01-01

    A 1972 survey of 30 Ottawa secondary schools revealed a total of 347 actual or potential X-ray sources available in these schools. More than half of these sources were gas discharge tubes. Some gas discharge tubes, in particular the cold cathode type, can emit X-rays at significantly high levels. Unless such tubes are used carefully, and with regard for good radiation safety practices, they can result in exposures to students that are in excess of the maximum levels recommended by the International Commission on Radiological Protection. Several cases of the recommended dose being exceeded were found in the classes surveyed. This document has been prepared to assist science teachers and others using demonstration-type gas discharge devices to select and use such devices so as to present negligible risk to themselves and students. Useful information on safety procedures to be followed when performing demonstrations or experiments is included. (J.T.A.)

  8. Aircraft operations management manual

    Science.gov (United States)

    1992-01-01

    The NASA aircraft operations program is a multifaceted, highly diverse entity that directly supports the agency mission in aeronautical research and development, space science and applications, space flight, astronaut readiness training, and related activities through research and development, program support, and mission management aircraft operations flights. Users of the program are interagency, inter-government, international, and the business community. This manual provides guidelines to establish policy for the management of NASA aircraft resources, aircraft operations, and related matters. This policy is an integral part of and must be followed when establishing field installation policy and procedures covering the management of NASA aircraft operations. Each operating location will develop appropriate local procedures that conform with the requirements of this handbook. This manual should be used in conjunction with other governing instructions, handbooks, and manuals.

  9. Determining quantitative road safety targets by applying statistical prediction techniques and a multi-stage adjustment procedure.

    Science.gov (United States)

    Wittenberg, P; Sever, K; Knoth, S; Sahin, N; Bondarenko, J

    2013-01-01

    Due to substantial progress made in road safety in the last ten years, the European Union (EU) renewed the ambitious agreement of halving the number of persons killed on the roads within the next decade. In this paper we develop a method that aims at finding an optimal target for each nation, in terms of being as achievable as possible, and with the cumulative EU target being reached. Targets as an important component in road safety policy are given as reduction rate or as absolute number of road traffic deaths. Determination of these quantitative road safety targets (QRST) is done by a top-down approach, formalized in a multi-stage adjustment procedure. Different QRST are derived under consideration of recent research. The paper presents a method to break the national target further down to regional targets in case of the German Federal States. Generalized linear models are fitted to data in the period 1991-2010. Our model selection procedure chooses various models for the EU and solely log-linear models for the German Federal States. If the proposed targets for the EU Member States are attained, the sum of fatalities should not exceed the total value of 15,465 per year by 2020. Both, the mean level and the range of mortality rates within the EU could be lowered from 28-113 in 2010 to 17-41 per million inhabitants in 2020. This study provides an alternative to the determination of safety targets by political commitments only, taking the history of road fatalities trends and population into consideration. Copyright © 2012 Elsevier Ltd. All rights reserved.

  10. Safety syringes and anti-needlestick devices in orthopaedic surgery.

    Science.gov (United States)

    Sibbitt, Wilmer L; Band, Philip A; Kettwich, Lawrence G; Sibbitt, Cristina R; Sibbitt, Lori J; Bankhurst, Arthur D

    2011-09-07

    The American Academy of Orthopaedic Surgery (AAOS), The Joint Commission, the Occupational Safety and Health Administration (OSHA), and the Needlestick Safety and Prevention Act encourage the integration of safety-engineered devices to prevent needlestick injuries to health-care workers and patients. We hypothesized that safety syringes and needles could be used in outpatient orthopaedic injection and aspiration procedures. The study investigated the orthopaedic uses and procedural idiosyncrasies of safety-engineered devices, including (1) four safety needles (Eclipse, SafetyGlide, SurGuard, and Magellan), (2) a mechanical safety syringe (RPD), (3) two automatic retractable syringes (Integra, VanishPoint), (4) three manual retractable syringes (Procedur-SF, Baksnap, Invirosnap), and (5) three shielded syringes (Safety-Lok, Monoject, and Digitally Activated Shielded [DAS] Syringe). The devices were first tested ex vivo, and then 1300 devices were used for 425 subjects undergoing outpatient arthrocentesis, intra-articular injections, local anesthesia, aspiration biopsy, and ultrasound-guided procedures. During the clinical observation, there were no accidental needlesticks (0 needlesticks per 1300 devices). Safety needles could be successfully used on a Luer syringe but were limited to ≤1.5 in (≤3.81 cm) in length and the shield could interfere with sonography. The mechanical safety syringes functioned well in all orthopaedic procedures. Automatic retractable syringes were too small for arthrocentesis of the knee, and the plunger blew out and prematurely collapsed with high-pressure injections. The manual retractable syringes and shielded syringes could be used with conventional needles for most orthopaedic procedures. The most effective and reliable safety devices for orthopaedic syringe procedures are shielded safety needles, mechanical syringes, manual retractable syringes, and shielded syringes, but not automatic retractable syringes. Even when adopting

  11. General Drafting. Technical Manual.

    Science.gov (United States)

    Department of the Army, Washington, DC.

    The manual provides instructional guidance and reference material in the principles and procedures of general drafting and constitutes the primary study text for personnel in drafting as a military occupational specialty. Included is information on drafting equipment and its use; line weights, conventions and formats; lettering; engineering charts…

  12. IAEA safeguards technical manual

    International Nuclear Information System (INIS)

    1980-02-01

    The necessity for statistical inference procedures arises because of time and cost limitations imposed on inspection activities, and also because of inherent limitations of inspection measurement instruments and techniques. This manual produces statistical concepts and techniques in the field of nuclear material control

  13. Coulometer operator's manual

    International Nuclear Information System (INIS)

    Criscuolo, A.L.

    1977-07-01

    The coulometer control system automates the titration of uranium and plutonium as performed by the CMB-1 group. The system consists of a printer, microcontroller, and coulometer, all of which are controlled by an algorithm stored in the microcontroller read-only memory. This manual describes the titration procedure using the coulometer control system, its theory and maintenance

  14. SNL Abuse Testing Manual.

    Energy Technology Data Exchange (ETDEWEB)

    Orendorff, Christopher [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lamb, Joshua [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Steele, Leigh Anna Marie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-07-01

    This report describes recommended abuse testing procedures for rechargeable energy storage systems (RESSs) for electric vehicles. This report serves as a revision to the FreedomCAR Electrical Energy Storage System Abuse Test Manual for Electric and Hybrid Electric Vehicle Applications (SAND2005-3123).

  15. Integration of a browser based operator manual in the system environment of a process computer system; Integration eines browserbasierten Betriebshandbuchs in die Systemumgebung einer Prozessrechneranlage

    Energy Technology Data Exchange (ETDEWEB)

    Weber, Andreas [Westinghouse Electric Germany GmbH (Germany); Erfle, Robert [DOSCO GmbH, Heidelberg (Germany); Feinkohl, Dirk [E.ON Kernkraft GmbH (Germany). Kernkraftwerk Unterweser

    2012-11-01

    The integration of a browser based operator manual in the system environment of a process computer system is an optimization of the operating procedure in the control room and a safety enhancement due to faster and error-free access to the manual contents. Several requirements by the authorities have to be fulfilled: the operating manual has to be available as hard copy, the format has to be true to original, protection against manipulation has to be provided, the manual content of the browser-based version and the hard copy have to identical, and the display presentation has to be consistent with ergonomic principals. The integration of the on-line manual in the surveillance process computer system provides the operator with the relevant comments to the surveillance signal. The described integration of the on-line manual is an optimization of the operator's everyday job with respect to ergonomics and safety (human performance).

  16. Structures manual

    Science.gov (United States)

    2001-01-01

    This manual was written as a guide for use by design personnel in the Vermont Agency of Transportation Structures Section. This manual covers the design responsibilities of the Section. It does not cover other functions that are a part of the Structu...

  17. Quality Manual

    Science.gov (United States)

    Koch, Michael

    The quality manual is the “heart” of every management system related to quality. Quality assurance in analytical laboratories is most frequently linked with ISO/IEC 17025, which lists the standard requirements for a quality manual. In this chapter examples are used to demonstrate, how these requirements can be met. But, certainly, there are many other ways to do this.

  18. IRS/TUEV activities during the licensing procedure. Safety assessment and preexamination

    International Nuclear Information System (INIS)

    Fendler, H.

    1976-01-01

    Short summary about the IRS/TUEV activities in the licensing procedure for a nuclear power plant: work for assessments, for pre-examination and approval specifications and drawings and for the quality control, time and the manpower necessary for this work. (orig./HP) [de

  19. Meat safety consequences of implementing visual postmortem meat inspection procedures in Danish slaughter pigs

    DEFF Research Database (Denmark)

    Mousing, Jan; Kyrval, J.; Jensen, Tim Kåre

    1997-01-01

    lymphadenitis, 7.0 faecally contaminated with Salmonella species, and 3.4 faecally contaminated with Yersinia enterocolitica would remain undetected as a result of changing from traditional to the visual inspection procedure. Two valuable reasons for implementing a visual control system are the potential...

  20. Research on the development of advanced system safety assessment procedures. 2

    International Nuclear Information System (INIS)

    Suzuki, Kazuhiko

    2004-02-01

    The past research reports in the area of safety engineering proposed the Computer-aided HAZOP system to be applied to Nuclear Reprocessing Facilities. Automated HAZOP system has great advantage compared with human analysts in terms of accuracy of the results, and time required to conduct HAZOP studies. However, it also became clear that the disadvantages are difficulty in analyzing the detailed information about a substance and a reaction peculiar to each plant or a process. And the outputted results may contain excess and deficiency compared with the HAZOP results performed by specialists. To improve HAZOP System, function of interventions by human is added to the system. Database-Bridge, which applies information management technology such as SQL operation, Query, is developed to perform intervention function. As the result the HAZOP system can give appropriate measures information to protect accidents to uses. Such HAZOP data is applied to safety management of Nuclear Reprocessing Facilities. (author)

  1. Research on the development of advanced system safety assessment procedures (1)

    International Nuclear Information System (INIS)

    Suzuki, Kazuhiko

    2002-02-01

    The past research reports in the area of safety engineering proposed the Computer-aided HAZOP system to be applied to Nuclear Reprocessing Facilities. Automated HAZOP system has great advantage compared with human analysts in terms of accuracy of the results, and time required to conduct HAZOP studies. This report surveys the literature on risk assessment and safety design based on the concept of independent protection layers (IPLs). Furthermore, to improve HAZOP System, counter measures information related to abnormal situation in plants are added to knowledge base in the system. As the result the HAZOP system can give appropriate measures information to protect accidents to uses. Such HAZOP system is applied to analyze the processes, where the ability of the proposed system is verified. (author)

  2. Safety

    International Nuclear Information System (INIS)

    1998-01-01

    A brief account of activities carried out by the Nuclear power plants Jaslovske Bohunice in 1997 is presented. These activities are reported under the headings: (1) Nuclear safety; (2) Industrial and health safety; (3) Radiation safety; and Fire protection

  3. Procedures for conducting probabilistic safety assessments of nuclear power plants (level 2). Accident progression, containment analysis and estimation of accident source terms

    International Nuclear Information System (INIS)

    1995-01-01

    The present publication on Level 2 PSA is based on a compilation and review of practices in various Member States. It complements Safety Series No. 50-P-4, issued in 1992, on Procedures for Conducting Probabilistic Safety Assessments of Nuclear Power Plants (Level 1). Refs, figs and tabs

  4. A working procedure for identifying emerging food safety issues at an early stage: Implications for European and international risk management practices

    NARCIS (Netherlands)

    Marvin, H.J.P.; Kleter, G.A.; Frewer, L.J.; Cope, S.F.; Wentholt, M.T.A.; Rowe, G.

    2009-01-01

    There is a need for early identification of emerging food safety issues in order to prevent them from developing into health risks. In this paper, various existing methods and procedures which can be used for early identification of safety issues are reviewed, including the monitoring of the

  5. Efficacy, safety, and patient acceptability of the Essure™ procedure

    OpenAIRE

    Hopkins, Matthew; Lessard,Collette

    2011-01-01

    Collette R Lessard, Matthew R HopkinsDepartment of Obstetrics and Gynecology, Mayo Clinic, Rochester, Minnesota, USAAbstract: The Essure™ system for permanent contraception was developed as a less invasive method of female sterilization. Placement of the Essure™ coil involves a hysteroscopic transcervical technique. This procedure can be done in a variety of settings and with a range of anesthetic options. More than eight years have passed since the US Food and Drug Admini...

  6. Radiological control manual. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Kloepping, R.

    1996-05-01

    This Lawrence Berkeley National Laboratory Radiological Control Manual (LBNL RCM) has been prepared to provide guidance for site-specific additions, supplements and interpretation of the DOE Radiological Control Manual. The guidance provided in this manual is one methodology to implement the requirements given in Title 10 Code of Federal Regulations Part 835 (10 CFR 835) and the DOE Radiological Control Manual. Information given in this manual is also intended to provide demonstration of compliance to specific requirements in 10 CFR 835. The LBNL RCM (Publication 3113) and LBNL Health and Safety Manual Publication-3000 form the technical basis for the LBNL RPP and will be revised as necessary to ensure that current requirements from Rules and Orders are represented. The LBNL RCM will form the standard for excellence in the implementation of the LBNL RPP.

  7. Radiological control manual. Revision 1

    International Nuclear Information System (INIS)

    Kloepping, R.

    1996-05-01

    This Lawrence Berkeley National Laboratory Radiological Control Manual (LBNL RCM) has been prepared to provide guidance for site-specific additions, supplements and interpretation of the DOE Radiological Control Manual. The guidance provided in this manual is one methodology to implement the requirements given in Title 10 Code of Federal Regulations Part 835 (10 CFR 835) and the DOE Radiological Control Manual. Information given in this manual is also intended to provide demonstration of compliance to specific requirements in 10 CFR 835. The LBNL RCM (Publication 3113) and LBNL Health and Safety Manual Publication-3000 form the technical basis for the LBNL RPP and will be revised as necessary to ensure that current requirements from Rules and Orders are represented. The LBNL RCM will form the standard for excellence in the implementation of the LBNL RPP

  8. Food Safety Impacts from Post-Harvest Processing Procedures of Molluscan Shellfish.

    Science.gov (United States)

    Baker, George L

    2016-04-18

    Post-harvest Processing (PHP) methods are viable food processing methods employed to reduce human pathogens in molluscan shellfish that would normally be consumed raw, such as raw oysters on the half-shell. Efficacy of human pathogen reduction associated with PHP varies with respect to time, temperature, salinity, pressure, and process exposure. Regulatory requirements and PHP molluscan shellfish quality implications are major considerations for PHP usage. Food safety impacts associated with PHP of molluscan shellfish vary in their efficacy and may have synergistic outcomes when combined. Further research for many PHP methods are necessary and emerging PHP methods that result in minimal quality loss and effective human pathogen reduction should be explored.

  9. DASS: A decision aid integrating the safety parameter display system and emergency functional recovery procedures. Final report

    International Nuclear Information System (INIS)

    Johnson, S.E.

    1984-08-01

    Using a stand-alone developmental test-bed consisting of a minicomputer and a high-resolution color graphics computer, displays and supporting software incorporating advanced on-line decision-aid concepts were developed and evaluated. The advanced concepts embodied in displays designed for the operating crew of a PWR plant include: (1) an integrated display format which supports a top-down approach to problem detection, recovery planning, and control; (2) introduction of nonobservable plant parameters derived from first principles mass and energy balances as part of the displayed information; and (3) systematic processing and display of key success path (plant safety system) attributes. The prototype system, referred to as the PWR-DASS (Disturbance Analysis and Surveillance System), consists of 18 displays targeted for principal use by the control room systems manager. PWR-DASS was conceived to fulfill an operational void not fully supported by safety parameter display systems or reformulated emergency procedure guidelines. The results from the evaluation by licensed operators suggest that organization and display of desired critical safety function and success path information as incorporated in the PWR-DASS prototype can support the systems manager's overview. The results also point to the need for several refinements required for a field grade system, and to the need for a simulator-based evaluation of the prototype or its successor. (author)

  10. Exploration and safety evaluations of salt formations and site selection procedures; Erkundung und Sicherheitsbewertung von Salzformationen und Standortauswahlverfahren

    Energy Technology Data Exchange (ETDEWEB)

    Krapf, Eva Barbara

    2016-12-12

    In 2011 the final decision for the withdrawal from the nuclear energy program was decided in the Federal Republic of Germany. The majority of the produced radioactive waste originate in the operation as well as in the decommissioning and dismantling of nuclear facilities. The long-term containment of especially heat-developing and high-level waste in an underground disposal facility is pursued. The Site Selection Act (StandAG), passed in 2013, defined further procedural steps as well as responsibilities and the way of public participation during the site selection. In this context the newly founded Commission Storage of Highly Radioactive Waste was assigned with the task of giving relevant recommendations based on their investigation of specific aspects and fundamental questions. The objective of this procedure is the selection of the site that can provide the best possible safety for humans and the environment during the defined period of one million years. The Commissions' final report was published in July 2016. In this thesis a possible approach for exploring sites in connection with safety investigations is recommended. The site selection procedure described in the StandAG represents the basis for the considerations. Geoscientific exclusion criteria, minimum requirements as well as weighing criteria can be developed regarding the relevant geoscientific and climatic changes during the defined period of one million years. In contrast to the recommendations made by the Commission Storage of Highly Radioactive Waste no previously existing report has been revised and adapted. Rather, all issues relevant for the long-term containment of radioactive waste in a disposal facility had been newly developed. The considerations are related to salt domes as host rock. Furthermore, according to the StandAG preliminary safety investigations are required in every step of the site selection. The recommendations made in this thesis concerning content and feasibility of

  11. Procedures and results of the probabilistic safety study of the HTR-1160 plant

    International Nuclear Information System (INIS)

    Kroeger, W.; Bongartz, R.

    1981-01-01

    A research team of the Institute for Nuclear Safety Research of the Juelich Nuclear Research Center (KFA) and staff members of the Gesellschaft fuer Reaktorsicherheit, sponsored by the Federal Ministry of the Interior, carried out a safety and risk analysis of high temperature reactors. The studies, which included the transfer to German conditions and the modification in some points of methodology of the American AIPA Study, were performed on the German concept of an 1160 MWe HTR with block-type fuel elements. They referred to accidents and possible impacts on the environment, residual risks and measures to reduce them. The study covered a total of approx. 15 groups of initiating events, including potential external impacts. The dominating initiating events are transients in a pressurized reactor. Differences relative to the light water reactor concept arise with respect to releases as a result of accidents and, above all, release times; they are due to different physical characteristics. HTR'S are characterized by thermal inertia and resistance to temperatures. If the results of the study are extended to the HTR line with a pebble bed core currently in the planning phase, the power densities alone, which are considerably lower in some designs, are indicative of an even more effective fission product retention than is already found in the HTR-1160 plant analyzed here. (orig.) [de

  12. Pacemaker replacement in nonagenarians: Procedural safety and long-term follow-up.

    Science.gov (United States)

    Loirat, Aurélie; Fénéon, Damien; Behaghel, Albin; Behar, Nathalie; Le Helloco, Alain; Mabo, Philippe; Daubert, Jean-Claude; Leclercq, Christophe; Martins, Raphaël P

    2015-01-01

    The rate of pacemaker implantation is rising. Given that the life expectancy of the population is projected to increase, a large number of elderly patients are likely to be implanted in the future. As pacemaker batteries can last for 8-10years, an increasing number of pacemaker recipients will require replacement of their devices when they become nonagenarians. To analyse the short- and long-term outcomes after device replacement in nonagenarians. Patients aged≥90years referred to a tertiary centre for pacemaker replacement from January 2004 to July 2014 were included retrospectively. Clinical follow-up data were obtained from clinical visits or telephone interviews with patients or their families. The primary clinical endpoint was total mortality. Secondary endpoints included early and delayed procedure-related complications and predictive risk factors for total mortality. Sixty-two patients were included (mean age 93.3±2.9years at time of pacemaker replacement). Mean procedure duration was 35.7±17.2minutes. Mean hospital stay was 2.2±1.1days. One patient died from a perioperative complication. Thirty-seven patients (59.7%) died during a median follow-up of 22.1months (interquartile range, 11.8-39.8months). Survival rates were 84.2% (95% confidence interval [CI] 71.8-91.5%) at 1year, 66.9% (95% CI 51.8-78.2%) at 2years and 22.7% (95% CI 10.6-37.7%) at 5years. Atrial fibrillation (hazard ratio 2.47, 95% CI 1.1-5.6) and non-physiological pacing (i.e. VVI pacing in patients in sinus rhythm) (hazard ratio 2.20, 95% CI 1.0-4.9) were predictors of mortality. Pacemaker replacement in nonagenarians is a safe and straightforward procedure. These data suggest that procedures can be performed securely in this old and frail population, with patients living for a median of 30months afterwards. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

  13. Recommended safety procedures for the selection, installation and use of baggage inspection x-ray equipment

    International Nuclear Information System (INIS)

    1978-05-01

    Good X-ray equipment alone will not preclude unnecessary exposure to x-radiation. The equipment must be installed, maintained and used by adequately trained personnel, with due regard for the inherent hazards of such equipment and an appreciation of the need to observe proper operational procedures. It is the intent of this Code to define equipment specifications and conditions of installation and use for baggage inspection X-ray equipment, such that the hazard to operating personnel and the general public from such devices remains negligibly small. (auth)

  14. NASA Safety Standard: Guidelines and Assessment Procedures for Limiting Orbital Debris

    Science.gov (United States)

    1995-01-01

    Collision with orbital debris is a hazard of growing concern as historically accepted practices and procedures have allowed man-made objects to accumulate in orbit. To limit future debris generation, NASA Management Instruction (NMI) 1700.8, 'Policy to Limit Orbital Debris Generation,' was issued in April of 1993. The NMI requires each program to conduct a formal assessment of the potential to generate orbital debris. This document serves as a companion to NMI 1700.08 and provides each NASA program with specific guidelines and assessment methods to assure compliance with the NMI. Each main debris assessment issue (e.g., Post Mission Disposal) is developed in a separate chapter.

  15. An independent safety assessment of Department of Energy nuclear reactor facilities: Procedures, operations and maintenance

    International Nuclear Information System (INIS)

    Toto, G.; Lindgren, A.J.

    1981-02-01

    The 1979 accident at the Three Mile Island commercial nuclear power plant has led to a number of studies of nuclear reactors, in both the public and private sectors. One of these is that of the Department of Energy's (DOE) Nuclear Facilities Personnel Qualification and Training (NFPQT) Committee, which has outlined tasks for assessment of 13 reactors owned by DOE and operated by contractors. This report covers one of the tasks, the assessment of procedures, operations, and maintenance at the DOE reactor facilities, based on a review of actual documents used at the reactor sites

  16. OSH technical reference manual

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-01

    In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

  17. Manual for subject analysis

    International Nuclear Information System (INIS)

    2002-01-01

    This document is one in a series of publications known as the ETDE/INIS Joint Reference Series and also constitutes a part of the ETDE Procedures Manual. It presents the rules, guidelines and procedures to be adopted by centers submitting input to the International Nuclear Information System (INIS) or the Energy Technology Data Exchange (ETDE). It is a manual for the subject analysis part of input preparation, meaning the selection, subject classification, abstracting and subject indexing of relevant publications, and is to be used in conjunction with the Thesauruses, Subject Categories documents and the documents providing guidelines for the preparation of abstracts. The concept and structure of the new manual are intended to describe in a logical and efficient sequence all the steps comprising the subject analysis of documents to be reported to INIS or ETDE. The manual includes new chapters on preparatory analysis, subject classification, abstracting and subject indexing, as well as rules, guidelines, procedures, examples and a special chapter on guidelines and examples for subject analysis in particular subject fields. (g.t.; a.n.)

  18. How safety procedures can follow the evolution in transport of RAM

    International Nuclear Information System (INIS)

    Sousselier, Y.; Grenier, M.

    1983-05-01

    In 1968, in Gatlimburg, an universal Convention was pointed out. It should help to erase many of the legal difficulties encountered in the international Transportation of Radioactive Material. About 15 years later, they have changed a little, they are still changing, but their status stays the same, they are still a basis for Organizations and Countries, as for instance recently for the Regulation issued by ICAO. It seems interesting to examine, under the light of the practical evolution in transport of radioactive materials, whether such a convention is still wishable, and what are the discernible lines of force and overall the solutions we can imagine to the present problems. The present situation is mainly characterized by two essential features: an increasing internationalization of Transportation of Radioactive Materials; and a stronger desire of checking the safety not only in the design of the packaging but also to check and act on the real shipment and the real package

  19. Procedures for conducting probabilistic safety assessments of nuclear power plants (Level 1)

    International Nuclear Information System (INIS)

    1992-01-01

    This report provides guidance for conducting a Level 1 of probabilistic safety assessment (PSA), that is a PSA concerned with events leading to core damage. The scope of this report is confined to internal initiating events (excluding internal fires and floods). A particular aim is to promote a standardized framework, terminology and form of documentation for PSAs so as to facilitate external review of the results of such studies. The report is divided into the following major sections: management and organization; identification of sources of radioactive releases and accident initiators; accident sequence modelling; data assessment and parameter estimation; accident sequence quantification; documentation of the analysis: display and interpretation of result. 45 refs, 7 figs, 23 tabs

  20. Management of Nuclear Safety in the USA: Administrative Procedures for Control

    Energy Technology Data Exchange (ETDEWEB)

    Stevenson, R. L.; Chitwood, R. B. [United States Atomic Energy Commission, Washington, DC (United States)

    1966-05-15

    Practices in preventing accidental criticality within the USAEC Regulatory Program for private industry are described, based on the authors' experience and familiarity with the operating organizations and processing plants, private or owned by the USAEC. The essentials for a programme for prevention of accidental criticality are defined and detailed appraisals are given for those facets requisite to successful implementation of a two contingency policy. In all cases the successful incorporation of the above elements depends upon management attitude, clearly defined functions and responsibilities, and well-understood working relationships between the responsible individuals. The interaction of these requisites is characterized by analyses of organizations spanning the range of complexity and criticality hazard potential encountered in the US industry. The importance of each of the many facets of control such as the selection of design approaches, training programmes, nuclear safety specifications, etc., is placed in perspective by referring to operating experiences and by defining the best features of each. (author)

  1. H12: Examination of safety assessment aims, procedures and results from a wider perspective

    International Nuclear Information System (INIS)

    Neall, F.B; Smith, P.A.

    2004-04-01

    Safety assessment (SA) are a familiar tool for the evaluation of disposal concepts for radioactive waste. There is, however, often confusion in the wider community about the aims, methods and results used in SA. This report aims to present the H12 SA in a way that makes the assessment process clearer and the implications of the results more meaningful both to workers within the SA field and to a wider technical audience. The reasonableness of the assessment results, the quality of the models and databases and redundancy within the natural and engineered barrier system have been considered. A number of recent and somewhat older SAs that address a range of different waste types, host rocks and disposal concepts have been considered, and comparisons made to H12. A further aim is to put both doses and timescales in a more meaningful context. It has been necessary to: consider ways of demonstrating the meaningfulness of calculations that give results for many thousands of years in the future; provide a framework timescale as a context for SA results over long times; demonstrate the smallness of the risk associated with the doses by comparison with other radiological and non-radiological risks. The perception of risk, which is a critical issue for public acceptance of radioactive waste disposal and must be considered when seeking to present safety assessment results 'in perspective' to a wider audience, is also discussed. It is concluded that H12 is comparable in many ways to assessments carried out internationally. Some assumptions are somewhat arbitrary reflecting the generic stage of the Japanese programme, and are likely to become better founded in future exercises. Nevertheless, H12 provides a clear and well-founded message that it is feasible to site and construct a safe repository from HLW in Japan. (author)

  2. Regional anesthesia for pediatric knee surgery: a review of the indications, procedures, outcomes, safety, and challenges

    Directory of Open Access Journals (Sweden)

    Muhly WT

    2015-11-01

    Full Text Available Wallis T Muhly, Harshad G Gurnaney, Arjunan GaneshDepartment of Anesthesiology and Critical Care Medicine, The Children’s Hospital of Philadelphia, Perelman School of Medicine at the University of Pennsylvania, Pennsylvania, PA, USAAbstract: The indications for surgery on the knee in children and adolescents share some similarity to adult practice in that there are an increasing number of sports-related injuries requiring surgical repair. In addition, there are some unique age-related conditions or congenital abnormalities that may present as indications for orthopedic intervention at the level of the knee. The efficacy and safety of peripheral nerve blocks (PNBs for postoperative analgesia following orthopedic surgery has been well established in adults. Recent studies have also demonstrated earlier functional recovery after surgery in patients who received PNBs. In children, PNB is gaining popularity, and increasing data are emerging to demonstrate the feasibility, efficacy, and safety in this population. In this paper, we will review some of the most common indications for surgery involving the knee in children and the anatomy of knee, associated dermatomal and osteotomal innervation, and the PNBs most commonly used to produce analgesia at the level of the knee. We will review the evidence in support of regional anesthesia in children in terms of both the quality conferred to the immediate postoperative care and the role of continuous PNBs in maintaining effective analgesia following discharge. Also we will discuss some of the subtle challenges in utilizing regional anesthesia in the pediatric patient including the use of general anesthesia when performing regional anesthesia and the issue of monitoring for compartment syndrome. Finally, we will offer some thoughts about areas of practice that are in need of further investigation.Keywords: pediatric surgery, regional anesthesia, analgesia, knee surgery

  3. Procedures for treating common cause failures in safety and reliability studies: Analytical background and techniques

    International Nuclear Information System (INIS)

    Mosleh, A.; Fleming, K.N.; Parry, G.W.; Paula, H.M.; Worledge, D.H.; Rasmuson, D.M.

    1989-01-01

    Volume I of this report presents a framework for the inclusion of the impact of common cause failures in risk and reliability evaluations. Common cause failures are defined as that subset of dependent failures for which causes are not explicitly included in the logic model as basic events. The emphasis here is on providing procedures for a practical, systematic approach that can be used to perform and clearly document the analysis. The framework and the methods discussed for performing the different stages of the analysis integrate insights obtained from engineering assessments of the system and the historical evidence from multiple failure events into a systematic, reproducible, and defensible analysis. This document, Volume 2, contains a series of appendices that provide additional background and methodological detail on several important topics discussed in Volume I

  4. Demographic, procedural and 30-day safety results from the WEB Intra-saccular Therapy Study (WEB-IT).

    Science.gov (United States)

    Fiorella, David; Molyneux, Andrew; Coon, Alexander; Szikora, Istvan; Saatci, Isil; Baltacioglu, Feyyaz; Sultan, Ali; Arthur, Adam

    2017-12-01

    The Woven EndoBridge (WEB) represents a novel intrasaccular therapeutic option for the treatment of intracranial wide-necked bifurcation aneurysms (WNBAs). The WEB-IT Study is a pivotal Investigational Device Exemption (IDE) study to determine the safety and effectiveness of the WEB device for the treatment of WNBAs located in the anterior and posterior intracranial circulations. We present the patient demographics, procedural characteristics, and 30-day adverse event data for the US WEB-IT study. WEB-IT is a prospective multicenter single-arm interventional study conducted at 25 US and 6 international centers. The study enrolled 150 adults with WNBAs of the anterior and posterior intracranial circulations. All patients were intended to receive a WEB device delivered via standard endovascular neurosurgical embolization techniques. The study was conducted under Good Clinical Practices and included independent adjudication effectiveness outcomes and all adverse events. One hundred and fifty patients enrolled at 27 investigational sites underwent attempted treatment with the WEB. Mean age was 59 years (range 29-79) and 110 (73.3%) of the patients were female. Treated aneurysms were located at the basilar apex (n=59, 39.3%), middle cerebral artery bifurcation (n=45, 30%), anterior communicating artery (n=40, 26.7%), and internal carotid artery terminus (n=6, 4%). Average aneurysm size was 6.4 mm (range 3.6-11.4) with a mean neck size of 4.8 mm (range 2.0-8.2, mean dome to neck ratio 1.34). Nine patients presented with ruptured aneurysms. Of the enrolled patients, 98.7% were treated successfully with WEB devices. Mean±SD fluoroscopy time was 30.2±15.7 min. One primary safety event (PSE) (0.7%)-a delayed parenchymal hemorrhage 22 days after treatment-occurred between the index procedure and 30-day follow-up. In addition to the single PSE, there were seven (4.7%) minor ischemic strokes (5 resolved without sequelae and 2 had a modified Rankin Scale score of 1

  5. H. W. Laboratory manual: 100 Area section

    Energy Technology Data Exchange (ETDEWEB)

    1950-07-01

    The purpose of this manual is to present a Hazard Breakdown of all jobs normally encountered in the laboratory work of the three sections comprising the Analytic Section, Metallurgy and Control Division of the Technical Department. A Hazard Breakdown is a careful analysis of any job in which the source of possible dangers is clearly indicated for each particular step. The analysis is prepared by individuals who are thoroughly familiar with the specific job or procedure. It is felt that if the hazards herein outlined are recognized by the Laboratory personnel and the suggested safety cautions followed, the chance for injury will be minimized and the worker will become generally more safety conscious. The manual, which is prefaced by the general safety rules applying to all the laboratories, is divided into three main sections, one for each of the three sections into which the Laboratories Division is divided. These sections are as follows: Section 1 -- 200 Area Control; Section 2 -- 100 Area Control; Section 3 -- 300 Area Control, Essential Materials, and Methods Improvement.

  6. A min cut-set-wise truncation procedure for importance measures computation in probabilistic safety assessment

    Energy Technology Data Exchange (ETDEWEB)

    Duflot, Nicolas [Universite de technologie de Troyes, Institut Charles Delaunay/LM2S, FRE CNRS 2848, 12, rue Marie Curie, BP2060, F-10010 Troyes cedex (France)], E-mail: nicolas.duflot@areva.com; Berenguer, Christophe [Universite de technologie de Troyes, Institut Charles Delaunay/LM2S, FRE CNRS 2848, 12, rue Marie Curie, BP2060, F-10010 Troyes cedex (France)], E-mail: christophe.berenguer@utt.fr; Dieulle, Laurence [Universite de technologie de Troyes, Institut Charles Delaunay/LM2S, FRE CNRS 2848, 12, rue Marie Curie, BP2060, F-10010 Troyes cedex (France)], E-mail: laurence.dieulle@utt.fr; Vasseur, Dominique [EPSNA Group (Nuclear PSA and Application), EDF Research and Development, 1, avenue du Gal de Gaulle, 92141 Clamart cedex (France)], E-mail: dominique.vasseur@edf.fr

    2009-11-15

    A truncation process aims to determine among the set of minimal cut-sets (MCS) produced by a probabilistic safety assessment (PSA) model which of them are significant. Several truncation processes have been proposed for the evaluation of the probability of core damage ensuring a fixed accuracy level. However, the evaluation of new risk indicators as importance measures requires to re-examine the truncation process in order to ensure that the produced estimates will be accurate enough. In this paper a new truncation process is developed permitting to estimate from a single set of MCS the importance measure of any basic event with the desired accuracy level. The main contribution of this new method is to propose an MCS-wise truncation criterion involving two thresholds: an absolute threshold in addition to a new relative threshold concerning the potential probability of the MCS of interest. The method has been tested on a complete level 1 PSA model of a 900 MWe NPP developed by 'Electricite de France' (EDF) and the results presented in this paper indicate that to reach the same accuracy level the proposed method produces a set of MCS whose size is significantly reduced.

  7. A min cut-set-wise truncation procedure for importance measures computation in probabilistic safety assessment

    International Nuclear Information System (INIS)

    Duflot, Nicolas; Berenguer, Christophe; Dieulle, Laurence; Vasseur, Dominique

    2009-01-01

    A truncation process aims to determine among the set of minimal cut-sets (MCS) produced by a probabilistic safety assessment (PSA) model which of them are significant. Several truncation processes have been proposed for the evaluation of the probability of core damage ensuring a fixed accuracy level. However, the evaluation of new risk indicators as importance measures requires to re-examine the truncation process in order to ensure that the produced estimates will be accurate enough. In this paper a new truncation process is developed permitting to estimate from a single set of MCS the importance measure of any basic event with the desired accuracy level. The main contribution of this new method is to propose an MCS-wise truncation criterion involving two thresholds: an absolute threshold in addition to a new relative threshold concerning the potential probability of the MCS of interest. The method has been tested on a complete level 1 PSA model of a 900 MWe NPP developed by 'Electricite de France' (EDF) and the results presented in this paper indicate that to reach the same accuracy level the proposed method produces a set of MCS whose size is significantly reduced.

  8. Development of seismic safety reevaluation procedure considering the ageing of NPP facilities

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Myoung Kue [Jeonju Univ., Cheonju (Korea, Republic of); Kim, J. M. [Cheonnam National Univ., Gwangju (Korea, Republic of); Kim, Y. S.; Cheong, S. H.; Kim, I. S.; Lee, M. G.; Kim, D. O. [Andong National Univ., Andong (Korea, Republic of); Lee, G. H. [Mokpo National Maritime Univ., Mokpo (Korea, Republic of)

    2003-03-15

    There are three of Nuclear Power Plants subject to the USI A-46 in Korea, including Kori No 1 and No 2 and Wolsung No 1. For the sake of resolution of the issue the possibility of adopting the GIP developed by the SQUG in USA is very high. In relation to the issue, this study addresses some technical improvements of the GIP including sloshing analysis based on multiple modes, seismic retrofit of cabinet for reduction of ICRS and modification of IRS depending on damping ratio. Dominant degradation factor and its affects NPP concrete elements are reviewed : chloride induced corrosion, carbonation of concrete elements, freezing and thawing of concrete elements, chemical and biological process, crack affect on concrete degradation. Various technical reports and papers about age-related degradation are reviewed for identification of degradation properties of NPP structures and components and degradation trend in NPP structures and components. This report summarizes numerical model for concrete degradation and development procedure of numerical models for concrete degradation. This report proposes the research necessity for performance evaluation of degraded concrete structure and selection of element for further study.

  9. Safety Precautions and Operating Procedures in an (A)BSL-4 Laboratory: 3. Aerobiology.

    Science.gov (United States)

    Bohannon, J Kyle; Janosko, Krisztina; Holbrook, Michael R; Barr, Jason; Pusl, Daniela; Bollinger, Laura; Coe, Linda; Hensley, Lisa E; Jahrling, Peter B; Wada, Jiro; Kuhn, Jens H; Lackemeyer, Matthew G

    2016-10-03

    Aerosol or inhalational studies of high-consequence pathogens have recently been increasing in number due to the perceived threat of intentional aerosol releases or unexpected natural aerosol transmission. Specific laboratories designed to perform these experiments require tremendous engineering controls to provide a safe and secure working environment and constant systems maintenance to sustain functionality. Class III biosafety cabinets, also referred to as gloveboxes, are gas-tight enclosures with non-opening windows. These cabinets are maintained under negative pressure by double high-efficiency-particulate-air (HEPA)-filtered exhaust systems and are the ideal primary containment for housing aerosolization equipment. A well planned workflow between staff members within high containment from, for instance, an animal biosafety level-4 (ABSL-4) suit laboratory to the ABSL-4 cabinet laboratory is a crucial component for successful experimentation. For smooth study execution, establishing a communication network, moving equipment and subjects, and setting up and placing equipment, requires staff members to meticulously plan procedures prior to study initiation. Here, we provide an overview and a visual representation of how aerobiology research is conducted at the National Institutes of Health, National Institute of Allergy and Infectious Diseases Integrated Research Facility at Fort Detrick, Maryland, USA, within an ABSL-4 environment.

  10. Thermal-Hydraulic System Codes in Nulcear Reactor Safety and Qualification Procedures

    Directory of Open Access Journals (Sweden)

    Alessandro Petruzzi

    2008-01-01

    Full Text Available In the last four decades, large efforts have been undertaken to provide reliable thermal-hydraulic system codes for the analyses of transients and accidents in nuclear power plants. Whereas the first system codes, developed at the beginning of the 1970s, utilized the homogenous equilibrium model with three balance equations to describe the two-phase flow, nowadays the more advanced system codes are based on the so-called “two-fluid model” with separation of the water and vapor phases, resulting in systems with at least six balance equations. The wide experimental campaign, constituted by the integral and separate effect tests, conducted under the umbrella of the OECD/CSNI was at the basis of the development and validation of the thermal-hydraulic system codes by which they have reached the present high degree of maturity. However, notwithstanding the huge amounts of financial and human resources invested, the results predicted by the code are still affected by errors whose origins can be attributed to several reasons as model deficiencies, approximations in the numerical solution, nodalization effects, and imperfect knowledge of boundary and initial conditions. In this context, the existence of qualified procedures for a consistent application of qualified thermal-hydraulic system code is necessary and implies the drawing up of specific criteria through which the code-user, the nodalization, and finally the transient results are qualified.

  11. Mitral valve surgery using right anterolateral thoracotomy: is the aortic cannulation a safety procedure?

    Science.gov (United States)

    Guedes, Marco Antonio Vieira; Pomerantzeff, Pablo Maria Alberto; Brandão, Carlos Manuel de Almeida; Vieira, Marcelo Luiz Campos; Grinberg, Max; Stolf, Noedir Antonio Groppo

    2010-01-01

    The right anterolateral thoracotomy is an alternative technique for surgical approach of mitral valve. In these cases, femoral-femoral bypass still has been used, rising occurrence of complications related to femoral cannulation. Describe the technique and results of mitral valve treatment by right anterolateral thoracotomy using aortic cannulation for cardiac pulmonary bypass (CPB). From 1983 e 2008, 100 consecutive female patients, with average age 35 ±13 years, 96 (96%) underwent mitral valve surgical treatment in the Heart Institute of São Paulo. A right anterolateral thoracotomy approach associated with aortic cannulation was used for CPB. Eighty (80%) patients had rheumatic disease and 84 (84%) patients presented functional class III or IV. Were performed 45 (45%) comissurotomies, 38 (38%) valve repairs, 7(7%) mitral valve replacements, seven (7%) recomissurotomies and three (3%) prosthesis replacement. Sparing surgery was performed in 90 (90%) patients. The average CPB and clamp time were 57 ± 27 min e 39 ± 19 min, respectively. There were no in-hospital death, reoperation due to bleeding and convertion to sternotomy. Introperative complications were related to heart harvest (5%), especially in reoperations (3%). The most important complications in postoperative period were related to pulmonary system (11%), followed by atrial fibrilation (10%) but without major systemic repercussions. The mean inhospital length of stay was 8 ± 3 days. Follow-up was 6.038 patients/month. Actuarial survival was 98.0 ± 1.9% and freedom from reoperation was 81.4 ± 7.8% in 180 months. The right anterolateral thoracotomy associated with aortic cannulation in mitral valve surgery is a simple technique, reproducible and safety.

  12. SHARP User Manual

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Y. Q. [Argonne National Lab. (ANL), Argonne, IL (United States); Shemon, E. R. [Argonne National Lab. (ANL), Argonne, IL (United States); Thomas, J. W. [Argonne National Lab. (ANL), Argonne, IL (United States); Mahadevan, Vijay S. [Argonne National Lab. (ANL), Argonne, IL (United States); Rahaman, Ronald O. [Argonne National Lab. (ANL), Argonne, IL (United States); Solberg, Jerome [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-03-31

    SHARP is an advanced modeling and simulation toolkit for the analysis of nuclear reactors. It is comprised of several components including physical modeling tools, tools to integrate the physics codes for multi-physics analyses, and a set of tools to couple the codes within the MOAB framework. Physics modules currently include the neutronics code PROTEUS, the thermal-hydraulics code Nek5000, and the structural mechanics code Diablo. This manual focuses on performing multi-physics calculations with the SHARP ToolKit. Manuals for the three individual physics modules are available with the SHARP distribution to help the user to either carry out the primary multi-physics calculation with basic knowledge or perform further advanced development with in-depth knowledge of these codes. This manual provides step-by-step instructions on employing SHARP, including how to download and install the code, how to build the drivers for a test case, how to perform a calculation and how to visualize the results. Since SHARP has some specific library and environment dependencies, it is highly recommended that the user read this manual prior to installing SHARP. Verification tests cases are included to check proper installation of each module. It is suggested that the new user should first follow the step-by-step instructions provided for a test problem in this manual to understand the basic procedure of using SHARP before using SHARP for his/her own analysis. Both reference output and scripts are provided along with the test cases in order to verify correct installation and execution of the SHARP package. At the end of this manual, detailed instructions are provided on how to create a new test case so that user can perform novel multi-physics calculations with SHARP. Frequently asked questions are listed at the end of this manual to help the user to troubleshoot issues.

  13. SHARP User Manual

    International Nuclear Information System (INIS)

    Yu, Y. Q.; Shemon, E. R.; Thomas, J. W.; Mahadevan, Vijay S.; Rahaman, Ronald O.; Solberg, Jerome

    2016-01-01

    SHARP is an advanced modeling and simulation toolkit for the analysis of nuclear reactors. It is comprised of several components including physical modeling tools, tools to integrate the physics codes for multi-physics analyses, and a set of tools to couple the codes within the MOAB framework. Physics modules currently include the neutronics code PROTEUS, the thermal-hydraulics code Nek5000, and the structural mechanics code Diablo. This manual focuses on performing multi-physics calculations with the SHARP ToolKit. Manuals for the three individual physics modules are available with the SHARP distribution to help the user to either carry out the primary multi-physics calculation with basic knowledge or perform further advanced development with in-depth knowledge of these codes. This manual provides step-by-step instructions on employing SHARP, including how to download and install the code, how to build the drivers for a test case, how to perform a calculation and how to visualize the results. Since SHARP has some specific library and environment dependencies, it is highly recommended that the user read this manual prior to installing SHARP. Verification tests cases are included to check proper installation of each module. It is suggested that the new user should first follow the step-by-step instructions provided for a test problem in this manual to understand the basic procedure of using SHARP before using SHARP for his/her own analysis. Both reference output and scripts are provided along with the test cases in order to verify correct installation and execution of the SHARP package. At the end of this manual, detailed instructions are provided on how to create a new test case so that user can perform novel multi-physics calculations with SHARP. Frequently asked questions are listed at the end of this manual to help the user to troubleshoot issues.

  14. Role of food safety in procedures adopted for the purchase of minimally processed and fresh vegetables by foodservices

    Directory of Open Access Journals (Sweden)

    Kátia Regina Martini Rodrigues

    2010-12-01

    Full Text Available This research was designed to analyze whether the procedures adopted by foodservice establishments for the purchase of minimally processed and fresh vegetables favor the acquisition of safe products. This research investigated the purchasing policies of such establishments, whether self-managed or administered by foodservice contractors, in the municipality of Campinas and its outlying districts. A random sample of thirty-nine establishments participated in the research. The instruments for data collection were pre-tested, and the actual interviews were conducted by trained personnel. Comparative analyses were made using various statistical tests. All of the participating establishments purchase fresh vegetables, although only six of them use minimally processed ones. For most of the establishments, price is at least one of the most important criteria for the selection of a supplier, and they do not normally monitor the safety of the fresh products purchased (51.3%, nor do they make regular technical visits to guarantee quality (46.2%; moreover, most do not carry out a supplier development program. It is suggested that routine technical visits to suppliers should be adopted, as well as the creation of courses, such as those dealing with the safety of vegetables and supplier development, to be offered to foodservices.

  15. Acucise™ endopyelotomy in a porcine model: procedure standardization and analysis of safety and immediate efficacy

    Directory of Open Access Journals (Sweden)

    Andreoni Cássio

    2004-01-01

    Full Text Available PURPOSE: The study here presented was done to test the technical reliability and immediate efficacy of the Acucise device using a standardized technique. MATERIALS AND METHODS: 56 Acucise procedures were performed in pigs by a single surgeon who used a standardized technique: insert 5F angiographic catheter bilaterally up to the midureter, perform retrograde pyelogram, Amplatz super-stiff guidewire is advanced up to the level of the renal pelvis, angiographic catheters are removed, Acucise catheter balloon is advanced to the ureteropelvic junction (UPJ level, the super-stiff guide-wire is removed and the contrast medium in the renal pelvis is aspirated and replaced with distilled water, activate Acucise at 75 watts of pure cutting current, keep the balloon fully inflated for 10 minutes, perform retrograde ureteropyelogram to document extravasation, remove Acucise catheter and pass an ureteral stent and remove guide-wire. RESULTS: In no case did the Acucise device present malfunction. The electrocautery activation time was 2.2 seconds (ranging from 2 to 4 seconds. The extravasation of contrast medium, visible by fluoroscopy, occurred in 53 of the 56 cases (94.6%. In no case there was any evidence of intraoperative hemorrhage. CONCLUSIONS: This study revealed that performing Acucise endopyelotomy routinely in a standardized manner could largely preclude intraoperative device malfunction and eliminate complications while achieving a successful incision in the UPJ. With the guidelines that were used in this study, we believe that Acucise endopyelotomy can be completed successfully and safely in the majority of selected patients with UPJ obstruction.

  16. SAFETY

    CERN Multimedia

    Niels Dupont

    2013-01-01

    CERN Safety rules and Radiation Protection at CMS The CERN Safety rules are defined by the Occupational Health & Safety and Environmental Protection Unit (HSE Unit), CERN’s institutional authority and central Safety organ attached to the Director General. In particular the Radiation Protection group (DGS-RP1) ensures that personnel on the CERN sites and the public are protected from potentially harmful effects of ionising radiation linked to CERN activities. The RP Group fulfils its mandate in collaboration with the CERN departments owning or operating sources of ionising radiation and having the responsibility for Radiation Safety of these sources. The specific responsibilities concerning "Radiation Safety" and "Radiation Protection" are delegated as follows: Radiation Safety is the responsibility of every CERN Department owning radiation sources or using radiation sources put at its disposition. These Departments are in charge of implementing the requi...

  17. T-3 cask users' manual. Revision 1

    International Nuclear Information System (INIS)

    1986-06-01

    This user's manual for the T-C spent fuel cask provides information on: operating procedures; inspection and maintenance procedures; criticality evaluation; shielding evaluation; thermal evaluation; structural evaluation; and limitations

  18. GRACE manual

    International Nuclear Information System (INIS)

    Ishikawa, T.; Kawabata, S.; Shimizu, Y.; Kaneko, T.; Kato, K.; Tanaka, H.

    1993-02-01

    This manual is composed of three kinds of objects, theoretical background for calculating the cross section of elementary process, usage and technical details of the GRACE system. Throughout this manual we take the tree level process e + e - → W + W - γ as an example, including the e ± -scalar boson interactions. The real FORTRAN source code for this process is attached in the relevant sections as well as the results of calculation, which might be a great help for understanding the practical use of the system. (J.P.N.)

  19. Laboratory biosafety manual

    Energy Technology Data Exchange (ETDEWEB)

    1983-01-01

    This book is in three sections; basic standards of laboratory design and equipment; procedures for safe laboratory practice; and the selection and use of essential biosafety equipment. The intention is that the guidance given in the book should have a broad basis and international application, and that it should be a source from which manuals applicable to local and special conditions can be usefully derived.

  20. Safety

    International Nuclear Information System (INIS)

    2001-01-01

    This annual report of the Senior Inspector for the Nuclear Safety, analyses the nuclear safety at EDF for the year 1999 and proposes twelve subjects of consideration to progress. Five technical documents are also provided and discussed concerning the nuclear power plants maintenance and safety (thermal fatigue, vibration fatigue, assisted control and instrumentation of the N4 bearing, 1300 MW reactors containment and time of life of power plants). (A.L.B.)

  1. Sandia SWiFT Wind Turbine Manual.

    Energy Technology Data Exchange (ETDEWEB)

    White, Jonathan; LeBlanc, Bruce Philip; Berg, Jonathan Charles; Bryant, Joshua; Johnson, Wesley D.; Paquette, Joshua

    2016-01-01

    The Scaled Wind Farm Technology (SWiFT) facility, operated by Sandia National Laboratories for the U.S. Department of Energy's Wind and Water Power Program, is a wind energy research site with multiple wind turbines scaled for the experimental study of wake dynamics, advanced rotor development, turbine control, and advanced sensing for production-scale wind farms. The SWiFT site currently includes three variable-speed, pitch-regulated, three-bladed wind turbines. The six volumes of this manual provide a detailed description of the SWiFT wind turbines, including their operation and user interfaces, electrical and mechanical systems, assembly and commissioning procedures, and safety systems. Further dissemination only as authorized to U.S. Government agencies and their contractors; other requests shall be approved by the originating facility or higher DOE programmatic authority. 111 UNCLASSIFIED UNLIMITED RELEASE Sandia SWiFT Wind Turbine Manual (SAND2016-0746 ) approved by: Department Manager SWiFT Site Lead Dave Minster (6121) Date Jonathan White (6121) Date SWiFT Site Supervisor Dave Mitchell (6121) Date Note: Document revision logs are found after the title page of each volume of this manual. iv

  2. Manual on quality assurance programme auditing

    International Nuclear Information System (INIS)

    1984-01-01

    The objective of this Manual is to provide guidance and illustrative examples of the methodology and techniques of internal and external audits that are consistent with the requirements and recommendations of the Code and the Safety Guide. The methodology and techniques are based on the practices of Member States having considerable experience in auditing QA programmes. This Manual is directed primarily towards QA programme auditors and managers and presents methods and techniques considered appropriate for the preparation and performance of audits and the evaluation of results. Its scope includes the techniques and methods used to carry out QA programme audits variously described as 'System', 'Product' and 'Process' audits. The techniques and methods described here may be used as one approach to the evaluation of suppliers' QA capabilities as defined in 50-SG-QA10. Although the Manual is primarily directed towards purchasers and suppliers, it is also relevant to regulatory organizations, such as government offices responsible for quality assurance, which carry out external audits independent of purchasers and suppliers. In such cases similar methods, procedures and techniques may be used

  3. Waste Management Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Buckingham, J.S. [ed.

    1967-08-31

    This Manual has been prepared to provide a documented compendium of the technical bases and general physical features of Isochem Incorporated`s Waste Management Program. The manual is intended to be used as a means of training and as a reference handbook for use by personnel responsible for executing the Waste Management Program. The material in this manual was assembled by members of Isochem`s Chemical Processing Division, Battelle Northwest Laboratory, and Hanford Engineering Services between September 1965 and March 1967. The manual is divided into the following parts: Introduction, contains a summary of the overall Waste Management Program. It is written to provide the reader with a synoptic view and as an aid in understanding the subsequent parts; Feed Material, contains detailed discussion of the type and sources of feed material used in the Waste Management Program, including a chapter on nuclear reactions and the formation of fission products; Waste Fractionization Plant Processing, contains detailed discussions of the processes used in the Waste Fractionization Plant with supporting data and documentation of the technology employed; Waste Fractionization Plant Product and Waste Effluent Handling, contains detailed discussions of the methods of handling the product and waste material generated by the Waste Fractionization Plant; Plant and Equipment, describes the layout of the Waste Management facilities, arrangement of equipment, and individual equipment pieces; Process Control, describes the instruments and analytical methods used for process control; and Safety describes process hazards and the methods used to safeguard against them.

  4. A Methods and procedures to apply probabilistic safety Assessment (PSA) techniques to the cobalt-therapy process. Cuban experience

    International Nuclear Information System (INIS)

    Vilaragut Llanes, J.J.; Ferro Fernandez, R.; Lozano Lima, B; De la Fuente Puch, A.; Dumenigo Gonzalez, C.; Troncoso Fleitas, M.; Perez Reyes, Y.

    2003-01-01

    This paper presents the results of the Probabilistic Safety Analysis (PSA) to the Cobalt Therapy Process, which was performed as part of the International Atomic Energy Agency's Coordinated Research Project (CRP) to Investigate Appropriate Methods and Procedures to Apply Probabilistic Safety Assessment (PSA) Techniques to Large Radiation Sources. The primary methodological tools used in the analysis were Failure Modes and Effects Analysis (FMEA), Event Trees and Fault Trees. These tools were used to evaluate occupational, public and medical exposures during cobalt therapy treatment. The emphasis of the study was on the radiological protection of patients. During the course of the PSA, several findings were analysed concerning the cobalt treatment process. In relation with the Undesired Events Probabilities, the lowest exposures probabilities correspond to the public exposures during the treatment process (Z21); around 10-10 per year, being the workers exposures (Z11); around 10-4 per year. Regarding to the patient, the Z33 probabilities prevail (not desired dose to normal tissue) and Z34 (not irradiated portion to target volume). Patient accidental exposures are also classified in terms of the extent to which the error is likely to affect individual treatments, individual patients, or all the patients treated on a specific unit. Sensitivity analyses were realised to determine the influence of certain tasks or critical stages on the results. As a conclusion the study establishes that the PSA techniques may effectively and reasonably determine the risk associated to the cobalt-therapy treatment process, though there are some weaknesses in its methodological application for this kind of study requiring further research. These weaknesses are due to the fact that the traditional PSA has been mainly applied to complex hardware systems designed to operate with a high automation level, whilst the cobalt therapy treatment is a relatively simple hardware system with a

  5. The Dyslexia Handbook: Procedures Concerning Dyslexia and Related Disorders = Manual sobre la dislexia: Procedimientos relacionados con la dislexia y otros desordenes.

    Science.gov (United States)

    Texas Education Agency, Austin.

    This handbook, available in English and Spanish, contains the Texas State Board of Education's approved procedures concerning dyslexia and related disorders and information regarding the state's dyslexia statutes and their relation to the federal Rehabilitation Act of 1973, Section 504, and the Individuals with Disabilities Education Act. Chapters…

  6. Hysterosalpingo-foam sonography (HyFoSy): Tolerability, safety and the occurrence of pregnancy post-procedure.

    Science.gov (United States)

    Tanaka, Keisuke; Chua, Jackie; Cincotta, Robert; Ballard, Emma L; Duncombe, Gregory

    2018-02-01

    Fallopian tube patency testing is an essential part of infertility evaluation. Hysterosalpingo-contrast sonography (HyCoSy) has been described as reliable, well tolerated and safe compared to other modalities such as laparoscopy and a dye test or hysterosalpingography. Limited availability of the previously used contrast has led to the introduction of a foam contrast agent as an alternative. To assess the tolerability, safety and occurrence of pregnancy post-procedure of hysterosalpingo-foam sonography (HyFoSy). A retrospective cohort study of women who had a HyFoSy at Queensland Ultrasound for Women from March 2013 to February 2015. A questionnaire was sent to their referring doctor to identify any complications or subsequent pregnancies with or without artificial reproductive technology (ART) within six months of the HyFoSy. Of 200 women, four cases were abandoned due to difficulty introducing the intracervical catheter, severe discomfort or a vasovagal episode. Response from referring doctors for 155 women reported no post-procedural complication. One hundred and eleven women were followed up for at least six months. Twenty-four out of 59 women (40.7%) who had ART and 24 out of 52 women (46.2%) who did not have ART conceived. Fifty percent of women who were nulligravida at the time of investigation, found to have at least one patent fallopian tube, whose partner had a normal semen analysis, spontaneously conceived within the time of follow up. HyFoSy is well tolerated and safe. A preponderance of pregnancies in the first month after HyFoSy suggests that a therapeutic effect may exist. © 2017 The Royal Australian and New Zealand College of Obstetricians and Gynaecologists.

  7. Metrication manual

    International Nuclear Information System (INIS)

    Harper, A.F.A.; Digby, R.B.; Thong, S.P.; Lacey, F.

    1978-04-01

    In April 1978 a meeting of senior metrication officers convened by the Commonwealth Science Council of the Commonwealth Secretariat, was held in London. The participants were drawn from Australia, Bangladesh, Britain, Canada, Ghana, Guyana, India, Jamaica, Papua New Guinea, Solomon Islands and Trinidad and Tobago. Among other things, the meeting resolved to develop a set of guidelines to assist countries to change to SI and to compile such guidelines in the form of a working manual

  8. Efficiency and Safety of One-Step Procedure Combined Laparoscopic Cholecystectomy and Eretrograde Cholangiopancreatography for Treatment of Cholecysto-Choledocholithiasis: A Randomized Controlled Trial.

    Science.gov (United States)

    Liu, Zhiyi; Zhang, Luyao; Liu, Yanling; Gu, Yang; Sun, Tieliang

    2017-11-01

    We aimed to evaluate the efficiency and safety of one-step procedure combined endoscopic retrograde cholangiopancreatography (ERCP) and laparoscopic cholecystectomy (LC) for treatment of patients with cholecysto-choledocholithiasis. A prospective randomized study was performed on 63 consecutive cholecysto-choledocholithiasis patients during 2008 and 2011. The efficiency and safety of one-step procedure was assessed by comparing the two-step LC with ERCP + endoscopic sphincterotomy (EST). Outcomes including intraoperative features, postoperative features (length of stay and postoperative complications) were evaluated. One- or two-step procedure of LC with ERCP + EST was successfully performed in all patients, and common bile duct stones were completely removed. Statistical analyses showed that length of stay and pulmonary infection rate were significantly lower in the test group compared with that in the control group (P 0.05). The one-step procedure of LC with ERCP + EST is superior to the two-step procedure for treatment of patients with cholecysto-choledocholithiasis regarding to the reduced hospital stay and inhibited occurrence of pulmonary infections. Compared with two-step procedure, one-step procedure of LC with ERCP + EST may be a superior option for cholecysto-choledocholithiasis patients treatment regarding to hospital stay and pulmonary infections.

  9. ENDF-6 Formats Manual. Data Formats and Procedures for the Evaluated Nuclear Data File ENDF/B-VI and ENDF/B-VII

    International Nuclear Information System (INIS)

    Herman, M.

    2009-01-01

    In December 2006, the Cross Section Evaluation Working Group (CSEWG) of the United States released the new ENDF/B-VII.0 library. This represented considerable achievement as it was the 1st major release since 1990 when ENDF/B-VI has been made publicly available. The two libraries have been released in the same format, ENDF-6, which has been originally developed for the ENDF/B-VI library. In the early stage of work on the VII-th generation of the library CSEWG made important decision to use the same formats. This decision was adopted even though it was argued that it would be timely to modernize the formats and several interesting ideas were proposed. After careful deliberation CSEWG concluded that actual implementation would require considerable resources needed to modify processing codes and to guarantee high quality of the files processed by these codes. In view of this the idea of format modernization has been postponed and ENDF-6 format was adopted for the new ENDF/B-VII library. In several other areas related to ENDF we made our best to move beyond established tradition and achieve maximum modernization. Thus, the 'Big Paper' on ENDF/B-VII.0 has been published, also in December 2006, as the Special Issue of Nuclear Data Sheets 107 (1996) 2931-3060. The new web retrieval and plotting system for ENDF-6 formatted data, Sigma, was developed by the NNDC and released in 2007. Extensive paper has been published on the advanced tool for nuclear reaction data evaluation, EMPIRE, in 2007. This effort was complemented with release of updated set of ENDF checking codes in 2009. As the final item on this list, major revision of ENDF-6 Formats Manual was made. This work started in 2006 and came to fruition in 2009 as documented in the present report.

  10. ENDF-6 Formats Manual Data Formats and Procedures for the Evaluated Nuclear Data File ENDF/B-VI and ENDF/B-VII

    Energy Technology Data Exchange (ETDEWEB)

    Herman, M.; Members of the Cross Sections Evaluation Working Group

    2009-06-01

    In December 2006, the Cross Section Evaluation Working Group (CSEWG) of the United States released the new ENDF/B-VII.0 library. This represented considerable achievement as it was the 1st major release since 1990 when ENDF/B-VI has been made publicly available. The two libraries have been released in the same format, ENDF-6, which has been originally developed for the ENDF/B-VI library. In the early stage of work on the VII-th generation of the library CSEWG made important decision to use the same formats. This decision was adopted even though it was argued that it would be timely to modernize the formats and several interesting ideas were proposed. After careful deliberation CSEWG concluded that actual implementation would require considerable resources needed to modify processing codes and to guarantee high quality of the files processed by these codes. In view of this the idea of format modernization has been postponed and ENDF-6 format was adopted for the new ENDF/B-VII library. In several other areas related to ENDF we made our best to move beyond established tradition and achieve maximum modernization. Thus, the 'Big Paper' on ENDF/B-VII.0 has been published, also in December 2006, as the Special Issue of Nuclear Data Sheets 107 (1996) 2931-3060. The new web retrieval and plotting system for ENDF-6 formatted data, Sigma, was developed by the NNDC and released in 2007. Extensive paper has been published on the advanced tool for nuclear reaction data evaluation, EMPIRE, in 2007. This effort was complemented with release of updated set of ENDF checking codes in 2009. As the final item on this list, major revision of ENDF-6 Formats Manual was made. This work started in 2006 and came to fruition in 2009 as documented in the present report.

  11. National Ignition Facility Project Site Safety Program

    International Nuclear Information System (INIS)

    Dun, C

    2003-01-01

    This Safety Program for the National Ignition Facility (NIF) presents safety protocols and requirements that management and workers shall follow to assure a safe and healthful work environment during activities performed on the NIF Project site. The NIF Project Site Safety Program (NPSSP) requires that activities at the NIF Project site be performed in accordance with the ''LLNL ES and H Manual'' and the augmented set of controls and processes described in this NIF Project Site Safety Program. Specifically, this document: (1) Defines the fundamental NIF site safety philosophy. (2) Defines the areas covered by this safety program (see Appendix B). (3) Identifies management roles and responsibilities. (4) Defines core safety management processes. (5) Identifies NIF site-specific safety requirements. This NPSSP sets forth the responsibilities, requirements, rules, policies, and regulations for workers involved in work activities performed on the NIF Project site. Workers are required to implement measures to create a universal awareness that promotes safe practice at the work site and will achieve NIF management objectives in preventing accidents and illnesses. ES and H requirements are consistent with the ''LLNL ES and H Manual''. This NPSSP and implementing procedures (e.g., Management Walkabout, special work procedures, etc.,) are a comprehensive safety program that applies to NIF workers on the NIF Project site. The NIF Project site includes the B581/B681 site and support areas shown in Appendix B

  12. Systematic safety evaluation of old nuclear power plants

    International Nuclear Information System (INIS)

    Dredemis, G.; Fourest, B.

    1984-01-01

    The French safety authorities have undertaken a systematic evaluation of the safety of old nuclear power plants. Apart from a complete revision of safety documents (safety analysis report, general operating rules, incident and accident procedures, internal emergency plan, quality organisation manual), this examination consisted of analysing the operating experience of systems frequently challenged and a systematic examination of the safety-related systems. This paper is based on an exercise at the Ardennes Nuclear Power Plant which has been in operation for 15 years. This paper also summarizes the main surveys and modifications relating to this power plant. (orig.)

  13. Development of a procedure for qualitative and quantitative evaluation of human factors as a part of probabilistic safety assessments of nuclear power plants. Part A

    International Nuclear Information System (INIS)

    Richei, A.

    1998-01-01

    The objective of this project is the development of a procedure for the qualitative and quantitative evaluation of human factors in the probabilistic safety assessment for nuclear power plants. The Human Error Rate Assessment and Optimizing System (HEROS) is introduced. The evaluation of a task with HEROS is realized in the three evaluation levels, i.e. 'Management Structure', 'Working Environment' and 'Man-Machine-Interface'. The developed expert system uses the fuzzy set theory for an assessment. For the evaluation of cognitive tasks evaluation criteria are derived also. The validation of the procedure is based on three examples, reflecting the common practice of probabilistic safety assessments and including problems, which cannot, respectively - only insufficiently - be evaluated with the established human risk analysis procedures. HERO applications give plausible and comprehensible results. (orig.) [de

  14. Employers' Occupational Health and Safety Training Obligations in Framework Directive and Training Procedure and Rules in Turkey

    OpenAIRE

    Nuray Gökçek Karaca; Berrin Gökçek

    2015-01-01

    Employers occupational safety and health training obligations are regulated in 89/391/EEC Framework Directive and also in 6331 numbered Occupational Health and Safety Law in Turkey. The main objective of this research is to determine and evaluate the employers’ occupational health and safety training obligations in Framework Directive in comparison with the 6331 numbered Occupational Health and Safety Law and to examine training principles in Turkey. For this purpose, ...

  15. Time efficient 124I-PET volumetry in benign thyroid disorders by automatic isocontour procedures: mathematic adjustment using manual contoured measurements in low-dose CT.

    Science.gov (United States)

    Freesmeyer, Martin; Kühnel, Christian; Westphal, Julian G

    2015-01-01

    Benign thyroid diseases are widely common in western societies. However, the volumetry of the thyroid gland, especially when enlarged or abnormally formed, proves to be a challenge in clinical routine. The aim of this study was to develop a simple and rapid threshold-based isocontour extraction method for thyroid volumetry from (124)I-PET/CT data in patients scheduled for radioactive iodine therapy. PET/CT data from 45 patients were analysed 30 h after 1 MBq (124)I administration. Anatomical reference volume was calculated using manually contoured data from low-dose CT images of the neck (MC). In addition, we applied an automatic isocontour extraction method (IC0.2/1.0), with two different threshold values (0.2 and 1.0 kBq/ml), for volumetry of the PET data-set. IC0.2/1.0 shape data that showed significant variation from MC data were excluded. Subsequently, a mathematical correlation using a model of linear regression with multiple variables and step-wise elimination (mIC0.2/1.0), between IC0.2/1.0 and MC, was established. Data from 41 patients (IC0.2), and 32 patients (IC1.0) were analysed. The mathematically calculated volume, mIC, showed a median deviation from the reference (MC), of ±9 % (1-54 %) for mIC0.2 and of ±8.2 % (1-50 %) for mIC1.0 CONCLUSION: Contour extraction with both, mIC1.0 and mIC0.2 gave rapid and reliable results. However, mIC0.2 can be applied to significantly more patients (>90 %) and is, therefore, deemed to be more suitable for clinical routine, keeping in mind the potential advantages of using (124)I-PET/CT for the preparation of patients scheduled for radioactive iodine therapy.

  16. Accident Prevention: A Workers' Education Manual.

    Science.gov (United States)

    International Labour Office, Geneva (Switzerland).

    Devoted to providing industrial workers with a greater knowledge of precautionary measures undertaken and enforced by industries for the protection of workers, this safety education manual contains 14 lessons ranging from "The Problems of Accidents during Work" to "Trade Unions and Workers and Industrial Safety." Fire protection, safety equipment…

  17. Manual for Cyclic Triaxial Test

    DEFF Research Database (Denmark)

    Shajarati, Amir; Sørensen, Kris Wessel; Nielsen, Søren Kjær

    This manual describes the different steps that is included in the procedure for conducting a cyclic triaxial test at the geotechnical Laboratory at Aalborg University. Furthermore it contains a chapter concerning some of the background theory for the static triaxial tests. The cyclic/dynamic tria......This manual describes the different steps that is included in the procedure for conducting a cyclic triaxial test at the geotechnical Laboratory at Aalborg University. Furthermore it contains a chapter concerning some of the background theory for the static triaxial tests. The cyclic...

  18. Materials Handling. Module SH-01. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on materials handling is one of 50 modules concerned with job safety and health. It presents the procedures for safe materials handling. Discussed are manual handling methods (lifting and carrying by hand) and mechanical lifting (lifting by powered trucks, cranes or conveyors). Following the introduction, 15 objectives (each…

  19. Involving patients in patient safety programmes: A scoping review and consensus procedure by the LINNEAUS collaboration on patient safety in primary care

    NARCIS (Netherlands)

    Trier, H.; Valderas, J.M.; Wensing, M.; Martin, H.M.; Egebart, J.

    2015-01-01

    BACKGROUND: Patient involvement has only recently received attention as a potentially useful approach to patient safety in primary care. OBJECTIVE: To summarize work conducted on a scoping review of interventions focussing on patient involvement for patient safety; to develop consensus-based

  20. SRC-I demonstration plant analytical laboratory methods manual. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Klusaritz, M.L.; Tewari, K.C.; Tiedge, W.F.; Skinner, R.W.; Znaimer, S.

    1983-03-01

    This manual is a compilation of analytical procedures required for operation of a Solvent-Refined Coal (SRC-I) demonstration or commercial plant. Each method reproduced in full includes a detailed procedure, a list of equipment and reagents, safety precautions, and, where possible, a precision statement. Procedures for the laboratory's environmental and industrial hygiene modules are not included. Required American Society for Testing and Materials (ASTM) methods are cited, and ICRC's suggested modifications to these methods for handling coal-derived products are provided.

  1. The use of living PSA in safety management, a procedure developed in the nordic project ''safety evaluation, NKS/SIK-1''

    International Nuclear Information System (INIS)

    Johanson, G.; Holmberg, J.

    1994-01-01

    The essential objective with the development of a living PSA concept is to bring the use of the plant specific PSA model out to the daily safety work to allow operational risk experience feedback and to increase the risk awareness of the intended users. This paper will present results of the Nordic project ''Safety Evaluation, NKS/SIK-1''. The SIK-1 project has defined and demonstrated the practical use of living PSA for safety evaluation and for identification of possible improvements in operational safety. Subjects discussed in this paper are dealing with the practical implementation and use of PSA to make proper safety related decisions and evaluation. (author). 24 refs, 1 fig., 1 tab

  2. Profiling safety of intravitreal injections for retinoblastoma using an anti-reflux procedure and sterilisation of the needle track.

    Science.gov (United States)

    Munier, Francis L; Soliman, Sameh; Moulin, Alexandre P; Gaillard, Marie-Claire; Balmer, Aubin; Beck-Popovic, Maja

    2012-08-01

    The preservation of globe integrity has always been a major concern during the treatment of retinoblastoma for fear of extraocular or metastatic spread. Intravitreal chemotherapy has been attempted as a desperate salvage therapy only for eyes with refractory retinoblastoma. Published data on the safety and efficacy of this route are, however, limited. A modified technique of intravitreal injection in eyes with retinoblastoma is described. All children with retinoblastoma who received one or more intravitreal injections using this technique were retrospectively reviewed concerning ocular complications of the injection procedure as well as clinical or histopathological evidence of tumour spread. 30 eyes of 30 children with retinoblastoma received a total of 135 intravitreal injections, with a median follw-up duration of 13.5 months. No extraocular spread was seen on clinical follow-up in any patients and there was no tumour contamination of the retrieved entry sites histopathologically analysed among the five enucleated eyes. No significant ocular side effects were observed except transient localised vitreous haemorrhage (3/135). This technique is potentially safe and effective at a low cost and may play a promising role, especially in the treatment of recurrent and/or resistant vitreous disease in retinoblastoma, as an alternative to enucleation and/or external beam radiotherapy. However, this treatment should not replace the primary standard of care of retinoblastoma and should not be considered in group E eyes. Its application should be approved by an ophthalmological-oncological team and it should be performed by an experienced eye surgeon in a tertiary referral centre after careful selection of a tumour-free injection site.

  3. Involving patients in patient safety programmes: A scoping review and consensus procedure by the LINNEAUS collaboration on patient safety in primary care.

    Science.gov (United States)

    Trier, Hans; Valderas, Jose M; Wensing, Michel; Martin, Helle Max; Egebart, Jonas

    2015-09-01

    Patient involvement has only recently received attention as a potentially useful approach to patient safety in primary care. To summarize work conducted on a scoping review of interventions focussing on patient involvement for patient safety; to develop consensus-based recommendations in this area. Scoping review of the literature 2006-2011 about methods and effects of involving patients in patient safety in primary care identified evidence for previous experiences of patient involvement in patient safety. This information was fed back to an expert panel for the development of recommendations for healthcare professionals and policy makers. The scoping review identified only weak evidence in support of the effectiveness of patient involvement. Identified barriers included a number of patient factors but also the healthcare workers' attitudes, abilities and lack of training. The expert panel recommended the integration of patient safety in the educational curricula for healthcare professionals, and expected a commitment from professionals to act as first movers by inviting and encouraging the patients to take an active role. The panel proposed a checklist to be used by primary care clinicians at the point of care for promoting patient involvement. There is only weak evidence on the effectiveness of patient involvement in patient safety. The recommendations of the panel can inform future policy and practice on patient involvement in safety in primary care.

  4. Review of cause-based decision tree approach for the development of domestic standard human reliability analysis procedure in low power/shutdown operation probabilistic safety assessment

    International Nuclear Information System (INIS)

    Kang, D. I.; Jung, W. D.

    2003-01-01

    We review the Cause-Based Decision Tree (CBDT) approach to decide whether we incorporate it or not for the development of domestic standard Human Reliability Analysis (HRA) procedure in low power/shutdown operation Probabilistic Safety Assessment (PSA). In this paper, we introduce the cause based decision tree approach, quantify human errors using it, and identify merits and demerits of it in comparision with previously used THERP. The review results show that it is difficult to incorporate the CBDT method for the development of domestic standard HRA procedure in low power/shutdown PSA because the CBDT method need for the subjective judgment of HRA analyst like as THERP. However, it is expected that the incorporation of the CBDT method into the development of domestic standard HRA procedure only for the comparision of quantitative HRA results will relieve the burden of development of detailed HRA procedure and will help maintain consistent quantitative HRA results

  5. ETAP user's manual

    International Nuclear Information System (INIS)

    Watanabe, Norio; Higuchi, Suminori.

    1990-11-01

    The event tree analysis technique has been used in Probabilistic Safety Assessment for LWRs to delineate various accident scenarios leading to core melt or containment failure and to evaluate their frequencies. This technique often requires manual preparation of event trees with iterative process and time-consuming work in data handling. For the purpose of reducing manual efforts in event tree analysis, we developed a new software package named ETAP (Event Tree Analysis Supporting Program) for event tree analysis. ETAP is an interactive PC-based program which has the ability to construct, update, document, and quantify event trees. Because of its fast running capability to quantify event trees, use of the EATP program can make it easy to perform the sensitivity studies on a variety of system/containment performance issues. This report provides a user's manual for ETAP, which describes the structure, installation, and use of EATP. This software runs on NEC/PC-9800 or compatible PCs that have a 640 KB memory and MS-DOS 2.11 or higher. (author)

  6. School Survey on Crime and Safety (SSOCS): 2015-16. Public-Use Data File User's Manual. NCES 2018-107

    Science.gov (United States)

    Jackson, Michael; Diliberti, Melissa; Kemp, Jana; Hummel, Steven; Cox, Christina; Gbondo-Tugbawa, Komba; Simon, Dillon

    2018-01-01

    The School Survey on Crime and Safety (SSOCS) is managed by the National Center for Education Statistics (NCES) within the Institute of Education Sciences of the U.S. Department of Education. SSOCS collects extensive crime and safety data from principals and administrators of public schools in the United States. Data from this collection can be…

  7. The role the safety analysis report and other documents in the licensing procedure in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Albrecht, E.; Ballhaus, S.

    1975-01-01

    Legal requirements for the licensing procedure, requirements for and preparation of licensing documents, authorities and experts participating in the licensing procedure, course of the atomic licensing procedure e.g. application for construction and operation, public hearing, site and concept license, partial licenses. (HP) [de

  8. Health physics instrument manual

    International Nuclear Information System (INIS)

    Gupton, E.D.

    1978-08-01

    The purpose of this manual is to provide apprentice health physics surveyors and other operating groups not directly concerned with radiation detection instruments a working knowledge of the radiation detection and measuring instruments in use at the Laboratory. The characteristics and applications of the instruments are given. Portable instruments, stationary instruments, personnel monitoring instruments, sample counters, and miscellaneous instruments are described. Also, information sheets on calibration sources, procedures, and devices are included. Gamma sources, beta sources, alpha sources, neutron sources, special sources, a gamma calibration device for badge dosimeters, and a calibration device for ionization chambers are described

  9. Rural Gas Program manual

    Energy Technology Data Exchange (ETDEWEB)

    1987-11-01

    The intent and purpose of this manual is to describe the various guideliness and administrative procedures associated with the Alberta Rural Gas Program and to consolidate and expand upon the legislation under which the Program has been developed. It is intended primarily for the use and information of rural gas distributors, their agents, and other private or government parties having an interest in the Rural Gas Program. Information is presented on: rural gas franchises, technical applications, contracts and tenders, determination of system capital costs for grant support, grants, Gas Alberta brokerage arrangements, insurance coverage, utility rights-of-way, and lien notes.

  10. SU-E-T-642: Safety Procedures for Error Elimination in Cyberknife Stereotactic Radiosurgery (SRS) and Stereotactic Body Radiation Therapy (SBRT)

    International Nuclear Information System (INIS)

    Hussain, A; Alkafi, A; Al-Najjar, W; Moftah, B

    2014-01-01

    Purpose: Cyberknife system is used for providing stereotactic radiosurgery (SRS) and stereotactic body radiation therapy (SBRT) hypofractionation scheme. The whole treatment delivery is based on live imaging of the patient. The minor error made at any stage may bring severe radiation injury to the patient or damage to the system itself. Several safety measures were taken to make the system safer. Methods: The radiation treatment provided thru a 6MV linac attached to Kuka robot (Cyberknife G4, Accuray Inc. Sunnyvale, CA, USA). Several possible errors were identified related to patient alignment, treatment planning, dose delivery and physics quality assurance. During dose delivery, manual and visual checks were introduced to confirm pre and intra-treatment imaging to reduce possible errors. One additional step was introduced to confirm that software tracking-tools had worked correctly with highest possible confidence level. Robotic head move in different orientations over and around the patient body, the rigidity of linac-head cover and other accessories was checked periodically. The vender was alerted when a tiny or bigger piece of equipment needed additional interlocked support. Results: As of our experience treating 525 patients on Cyberknife during the last four years, we saw on and off technical issues. During image acquisition, it was made essential to follow the site-specific imaging protocols. Adequate anatomy was contoured to document the respective doses. Followed by auto-segmentation, manual tweaking was performed on every structure. The calculation box was enclosing the whole image during the final calculation. Every plan was evaluated on slice-by slice basis. To review the whole process, a check list was maintained during the physics 2nd-check. Conclusion: The implementation of manual and visual additional checks introduced along with automated checks for confirmation was found promising in terms of reduction in systematic errors and making the system

  11. A Clinical Study on Management of Incomplete Abortion by Manual Vacuum Aspiration (MVA

    Directory of Open Access Journals (Sweden)

    Arifa Akter Jahan

    2012-07-01

    Full Text Available Background: Abortion is an important social and public health issue. In Bangladesh complication from unsafe abortion is one of the leading causes of maternal mortality. It is a serious health problem. World Health Organisation estimates that 14% of maternal deaths which occur every year in the countries of South Asia including Bangladesh are due to abortion. Study shows manual vacuum aspiration procedure is safe and effective in incomplete abortion. Very few clinical trials were carried out in Bangladesh to assess the safety and effectivity of manual vacuum aspiration in managing incomplete abortion. Objective: To find out the outcome of manual vacuum aspiration in the management of patients of incomplete abortion. Materials and Methods: This observational descriptive study was conducted in the department of Obstetrics & Gynaecology, Dhaka Medical College & Hospital from June to December, 2004. One hundred cases of diagnosed incomplete abortion up to 12 weeks of gestation were managed by manual vacuum aspiration during this period. A data recording sheet was designed for this purpose. Haemodynamically stable patients with no history of induced abortion and fever were enrolled. Results: Procedure time of manual vacuum aspiration was short, average duration was 7 minutes. Bleeding was minimum (20-30 mL in 67% cases and weighted mean was 29.80 mL. Eighty three percent patients were stable during the procedure and only 3% needed blood transfusion. Nonnarcotic analgesics were used in 59% cases and 33% needed only proper counselling. Average duration of hospital stay was 2 hours. Effectiveness of the procedure was about 98% with very low post procedure complication rate (2%. Conclusion: MVA procedure is a safe and effective technique of uterine evacuation in incomplete abortion. It is quick, less expensive, effective and less painful. Hospital stay and chance of perforation of uterus is less. So this procedure should be considered by health care

  12. Pdap Manual

    DEFF Research Database (Denmark)

    Pedersen, Mads Mølgaard; Larsen, Torben J.

    Pdap, Python Data Analysis Program, is a program for post processing, analysis, visualization and presentation of data e.g. simulation results and measurements. It is intended but not limited to the domain of wind turbines. It combines an intuitive graphical user interface with python scripting...... that allows automation and implementation of custom functions. This manual gives a short introduction to the graphical user interface, describes the mathematical background for some of the functions, describes the scripting API and finally a few examples on how automate analysis via scripting is presented....... The newest version, and more documentation and help on how to used, extend and automate Pdap can be found at the webpage www.hawc2.dk...

  13. Procedure for estimating permanent total enclosure costs

    Energy Technology Data Exchange (ETDEWEB)

    Lukey, M E; Prasad, C; Toothman, D A; Kaplan, N

    1999-07-01

    Industries that use add-on control devices must adequately capture emissions before delivering them to the control device. One way to capture emissions is to use permanent total enclosures (PTEs). By definition, an enclosure which meets the US Environmental Protection Agency's five-point criteria is a PTE and has a capture efficiency of 100%. Since costs play an important role in regulatory development, in selection of control equipment, and in control technology evaluations for permitting purposes, EPA has developed a Control Cost Manual for estimating costs of various items of control equipment. EPA's Manual does not contain any methodology for estimating PTE costs. In order to assist environmental regulators and potential users of PTEs, a methodology for estimating PTE costs was developed under contract with EPA, by Pacific Environmental Services, Inc. (PES) and is the subject of this paper. The methodology for estimating PTE costs follows the approach used for other control devices in the Manual. It includes procedures for sizing various components of a PTE and for estimating capital as well as annual costs. It contains verification procedures for demonstrating compliance with EPA's five-point criteria. In addition, procedures are included to determine compliance with Occupational Safety and Health Administration (OSHA) standards. Meeting these standards is an important factor in properly designing PTEs. The methodology is encoded in Microsoft Exel spreadsheets to facilitate cost estimation and PTE verification. Examples are given throughout the methodology development and in the spreadsheets to illustrate the PTE design, verification, and cost estimation procedures.

  14. Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management. Rules of Procedure and Financial Rules

    International Nuclear Information System (INIS)

    2006-01-01

    The 'Rules of Procedure and Financial Rules' adopted at the Preparatory Meeting of the Contracting Parties to the Joint Convention held from 10 to 12 December 2001 were modified at the First Review Meeting of Contracting Parties held from 3 to 14 November 2003 and the Extraordinary Meeting of Contracting Parties held on 7 November 2005. The modified 'Rules of Procedure and Financial Rules' are set forth in the Attachment hereto

  15. Zooplankton Methodology, Collection & identyification - A field manual

    Digital Repository Service at National Institute of Oceanography (India)

    Goswami, S.C.

    and productivity would largely depend upon the use of correct methodology which involves collection of samples, fixation, preservation, analysis and computation of data. The detailed procedures on all these aspects are given in this manual....

  16. Manual of mathematical techniques for linefish assessment

    CSIR Research Space (South Africa)

    Butterworth, DS

    1989-01-01

    Full Text Available This manual contains an expanded version of material presented at a Linefish Population Dynamics Workshop held in Cape Town in February 1987. First the statistical procedures for fitting curves to data are discussed. The standard single...

  17. SAFETY

    CERN Multimedia

    M. Plagge, C. Schaefer and N. Dupont

    2013-01-01

    Fire Safety – Essential for a particle detector The CMS detector is a marvel of high technology, one of the most precise particle measurement devices we have built until now. Of course it has to be protected from external and internal incidents like the ones that can occur from fires. Due to the fire load, the permanent availability of oxygen and the presence of various ignition sources mostly based on electricity this has to be addressed. Starting from the beam pipe towards the magnet coil, the detector is protected by flooding it with pure gaseous nitrogen during operation. The outer shell of CMS, namely the yoke and the muon chambers are then covered by an emergency inertion system also based on nitrogen. To ensure maximum fire safety, all materials used comply with the CERN regulations IS 23 and IS 41 with only a few exceptions. Every piece of the 30-tonne polyethylene shielding is high-density material, borated, boxed within steel and coated with intumescent (a paint that creates a thick co...

  18. SAFETY

    CERN Multimedia

    C. Schaefer and N. Dupont

    2013-01-01

      “Safety is the highest priority”: this statement from CERN is endorsed by the CMS management. An interpretation of this statement may bring you to the conclusion that you should stop working in order to avoid risks. If the safety is the priority, work is not! This would be a misunderstanding and misinterpretation. One should understand that “working safely” or “operating safely” is the priority at CERN. CERN personnel are exposed to different hazards on many levels on a daily basis. However, risk analyses and assessments are done in order to limit the number and the gravity of accidents. For example, this process takes place each time you cross the road. The hazard is the moving vehicle, the stake is you and the risk might be the risk of collision between both. The same principle has to be applied during our daily work. In particular, keeping in mind the general principles of prevention defined in the late 1980s. These principles wer...

  19. Nuclear materials management procedures

    International Nuclear Information System (INIS)

    Veevers, K.; Silver, J.M.; Quealy, K.J.; Steege, E. van der.

    1987-10-01

    This manual describes the procedures for the management of nuclear materials and associated materials at the Lucas Heights Research Laboratories. The procedures are designed to comply with Australia's nuclear non-proliferation obligations to the International Atomic Energy Agency (IAEA), bilateral agreements with other countries and ANSTO's responsibilities under the Nuclear Non-Proliferation (Safeguards) Act, 1987. The manual replaces those issued by the Australian Atomic Energy Commission in 1959, 1960 and 1969

  20. Improving medication safety in primary care. A review and consensus procedure by the LINNEAUS collaboration on patient safety in primary care

    NARCIS (Netherlands)

    Lainer, M.; Vogele, A.; Wensing, M.; Sonnichsen, A.

    2015-01-01

    BACKGROUND: Drug treatment is an important clinical process in primary care that is associated with risk of error and adverse events. OBJECTIVE: To review currently available research evidence on the topic and to develop a framework, which can help to guide improvement of medication safety. METHODS:

  1. 78 FR 33146 - Importance of Clear Safety Procedures for Temporary Removal From Service of Highway-Rail Grade...

    Science.gov (United States)

    2013-06-03

    ... Safety Advisory 2002-01. FOR FURTHER INFORMATION CONTACT: George Hartman, Staff Director, Signal and...., Washington, DC 20590 (phone: 202-493- 6225, email: George.Hartman@dot.gov ), or Kathryn Shelton, Trial...

  2. Investigation of the possibility of a calculative reactor safety estimation in the licence procedure for nuclear reactors

    International Nuclear Information System (INIS)

    Adler, B.; Kampf, T.

    1975-12-01

    Up to now it is impossible to calculate completely the safety of nuclear reactors. Therefore the authors have collected and employed a number of at a high degree independent safety parameters for mathematical evaluation of the reactor safety. By means of computer programs such parameters from about 400 research reactors have been analysed and the fluctuation ranges of their greatest density were determined. The limits of these fluctuation ranges are quickly available and can be used as recommended values for the layout and for the safety estimation of research reactors. A comparison of the existing layout recommendations and the determined fluctuation ranges in most cases shows a good agreement. In some cases corrections and new layout recommendations have been proposed. The determined fluctuation ranges found their first practical application in the estimation of the Rossendorf Equipment for Critical Experiments (RAKE). (author)

  3. Safety

    International Nuclear Information System (INIS)

    Jones, P.M.S.

    1987-01-01

    Aspects of fission reactors are considered - control, heat removal and containment. Brief descriptions of the reactor accidents at the SL-1 reactor (1961), Windscale (1957), Browns Ferry (1975), Three Mile Island (1979) and Chernobyl (1986) are given. The idea of inherently safe reactor designs is discussed. Safety assessment is considered under the headings of preliminary hazard analysis, failure mode analysis, event trees, fault trees, common mode failure and probabalistic risk assessments. These latter can result in a series of risk distributions linked to specific groups of fault sequences and specific consequences. A frequency-consequence diagram is shown. Fatal accident incidence rates in different countries including the United Kingdom for various industries are quoted. The incidence of fatal cancers from occupational exposure to chemicals is tabulated. Human factors and the acceptability of risk are considered. (U.K.)

  4. HANSF 1.3 Users Manual FAI/98-40-R2 Hanford Spent Nuclear Fuel (SNF) Safety Analysis Model [SEC 1 and 2

    Energy Technology Data Exchange (ETDEWEB)

    DUNCAN, D.R.

    1999-10-07

    The HANSF analysis tool is an integrated model considering phenomena inside a multi-canister overpack (MCO) spent nuclear fuel container such as fuel oxidation, convective and radiative heat transfer, and the potential for fission product release. This manual reflects the HANSF version 1.3.2, a revised version of 1.3.1. HANSF 1.3.2 was written to correct minor errors and to allow modeling of condensate flow on the MCO inner surface. HANSF 1.3.2 is intended for use on personal computers such as IBM-compatible machines with Intel processors running under Lahey TI or digital Visual FORTRAN, Version 6.0, but this does not preclude operation in other environments.

  5. The effect of facility characteristics on patient safety, patient experience, and service availability for procedures in non-hospital-affiliated outpatient settings: A systematic review.

    Science.gov (United States)

    Berglas, Nancy F; Battistelli, Molly F; Nicholson, Wanda K; Sobota, Mindy; Urman, Richard D; Roberts, Sarah C M

    2018-01-01

    Over recent decades, numerous medical procedures have migrated out of hospitals and into freestanding ambulatory surgery centers (ASCs) and physician offices, with possible implications for patient outcomes. In response, states have passed regulations for office-based surgeries, private organizations have established standards for facility accreditation, and professional associations have developed clinical guidelines. While abortions have been performed in office setting for decades, states have also enacted laws requiring that facilities that perform abortions meet specific requirements. The extent to which facility requirements have an impact on patient outcomes-for any procedure-is unclear. We conducted a systematic review to examine the effect of outpatient facility type (ASC vs. office) and specific facility characteristics (e.g., facility accreditation, emergency response protocols, clinician qualifications, physical plant characteristics, other policies) on patient safety, patient experience and service availability in non-hospital-affiliated outpatient settings. To identify relevant research, we searched databases of the published academic literature (PubMed, EMBASE, Web of Science) and websites of governmental and non-governmental organizations. Two investigators reviewed 3049 abstracts and full-text articles against inclusion/exclusion criteria and assessed the quality of 22 identified articles. Most studies were hampered by methodological challenges, with 12 of 22 not meeting minimum quality criteria. Of 10 studies included in the review, most (6) examined the effect of facility type on patient safety. Existing research appears to indicate no difference in patient safety for outpatient procedures performed in ASCs vs. physician offices. Research about specific facility characteristics is insufficient to draw conclusions. More and higher quality research is needed to determine if there is a public health problem to be addressed through facility

  6. Hanford whole body counting manual

    International Nuclear Information System (INIS)

    Palmer, H.E.; Brim, C.P.; Rieksts, G.A.; Rhoads, M.C.

    1987-05-01

    This document, a reprint of the Whole Body Counting Manual, was compiled to train personnel, document operation procedures, and outline quality assurance procedures. The current manual contains information on: the location, availability, and scope of services of Hanford's whole body counting facilities; the administrative aspect of the whole body counting operation; Hanford's whole body counting facilities; the step-by-step procedure involved in the different types of in vivo measurements; the detectors, preamplifiers and amplifiers, and spectroscopy equipment; the quality assurance aspect of equipment calibration and recordkeeping; data processing, record storage, results verification, report preparation, count summaries, and unit cost accounting; and the topics of minimum detectable amount and measurement accuracy and precision. 12 refs., 13 tabs

  7. Reactor safety

    International Nuclear Information System (INIS)

    Butz, H.P.; Heuser, F.W.; May, H.

    1985-01-01

    The paper comprises an introduction into nuclear physics bases, the safety concept generally speaking, safety devices of pwr type reactors, accident analysis, external influences, probabilistic safety assessment and risk studies. It further describes operational experience, licensing procedures under the Atomic Energy Law, research in reactor safety and the nuclear fuel cycle. (DG) [de

  8. Assessment of procedural skills in residents working in a research and training institute: An effort to ensure patient safety and quality control.

    Science.gov (United States)

    Kumari, Kamlesh; Samra, Tanvir; Naik, B Naveen; Saini, Vikas

    2018-01-01

    To ensure patient safety, it is important to regularly assess the knowledge and practical skills of anesthesia trainees. This study was conducted to evaluate the competency of the residents and the impact of various corrective measures in the form of didactic lectures and clinical skill demonstrations on the conduct of various procedural skills by the residents. Ninety-five junior residents were enrolled in this study. Assessment of competency of 1 st , 2 nd , and 3 rd year residents in performing various procedure skills of anesthesia was done in two stages using procedure specific checklist (PSC) and Global Rating Scales (GRSs). Preliminary results of the first assessment (Score 1) were discussed with the residents; deficiencies were identified and corrective measures suggested by didactic lectures and clinical skill demonstrations which were followed by a subsequent assessment after 3 months (Score 2). There was a statistically significant improvement in the PSC and GRS scores after corrective measures for all the procedural interventions studied. Percentage increase in scores was maximum in 1 st year (42.98 ± 6.62) followed by 2 nd year (34.62 ± 5.49) and minimum in 3 rd year residents (18.06 ± 3.69). The percentage increase of scores was almost similar for all subset of procedural skills; low, intermediate, and high skill anesthetic procedures. For assessment of procedural skills of residents, use of PSC and GRS scores should be incorporated and the same should be used to monitor the impact of various corrective measures (didactic lectures and clinical skill demonstrations) on the conduct of various procedural skills by the resident.

  9. WAM-E user's manual

    International Nuclear Information System (INIS)

    Rayes, L.G.; Riley, J.E.

    1986-07-01

    The WAM-E series of mainframe computer codes have been developed to efficiently analyze the large binary models (e.g., fault trees) used to represent the logic relationships within and between the systems of a nuclear power plant or other large, multisystem entity. These codes have found wide application in reliability and safety studies of nuclear power plant systems. There are now nine codes in the WAM-E series, with six (WAMBAM/WAMTAP, WAMCUT, WAMCUT-II, WAMFM, WAMMRG, and SPASM) classified as Type A Production codes and the other three (WAMFTP, WAMTOP, and WAMCONV) classified as Research codes. This document serves as a combined User's Guide, Programmer's Manual, and Theory Reference for the codes, with emphasis on the Production codes. To that end, the manual is divided into four parts: Part I, Introduction; Part II, Theory and Numerics; Part III, WAM-E User's Guide; and Part IV, WAMMRG Programmer's Manual

  10. Light-water-reactor hydrogen manual

    International Nuclear Information System (INIS)

    Camp, A.L.; Cummings, J.C.; Sherman, M.P.; Kupiec, C.F.; Healy, R.J.; Caplan, J.S.; Sandhop, J.R.; Saunders, J.H.

    1983-06-01

    A manual concerning the behavior of hydrogen in light water reactors has been prepared. Both normal operations and accident situations are addressed. Topics considered include hydrogen generation, transport and mixing, detection, and combustion, and mitigation. Basic physical and chemical phenomena are described, and plant-specific examples are provided where appropriate. A wide variety of readers, including operators, designers, and NRC staff, will find parts of this manual useful. Different sections are written at different levels, according to the most likely audience. The manual is not intended to provide specific plant procedures, but rather, to provide general guidance that may assist in the development of such procedures

  11. Towards Automatic Capturing of Manual Data Processing Provenance

    NARCIS (Netherlands)

    Wombacher, Andreas; Huq, M.R.

    2011-01-01

    Often data processing is not implemented by a work ow system or an integration application but is performed manually by humans along the lines of a more or less specified procedure. Collecting provenance information during manual data processing can not be automated. Further, manual collection of

  12. 14 CFR 21.5 - Airplane or Rotorcraft Flight Manual.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Airplane or Rotorcraft Flight Manual. 21.5... CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS General § 21.5 Airplane or Rotorcraft Flight Manual. (a) With each airplane or rotorcraft that was not type certificated with an Airplane or Rotorcraft Flight Manual...

  13. A procedure for the analysis of errors of commission in a Probabilistic Safety Assessment of a nuclear power plant at full power

    International Nuclear Information System (INIS)

    Julius, J.; Jorgenson, E.; Parry, G.W.; Mosleh, A.M.

    1995-01-01

    This paper describes an analytical procedure that has been developed to facilitate the identification of errors of commission for inclusion in a Probabilistic Safety Assessment (PSA) of a nuclear power plant operating at full power. The procedure first identifies the opportunities for error by determining when operators are required to intervene to bring the plant to a safe condition following a transient, and then identifying under what conditions this is likely to occur using a model of the causes of error. In order to make the analysis practicable, a successive screening approach is used to identify those errors with the highest potential of occurrence. The procedure has been applied as part of a PSA study, and the results of that application are summarized. For the particular plant to which the procedure was applied, the conclusion was that, because of the nature of the procedures, the high degree of redundancy in the instrumentation, the operating practices, and the control board layouts, the potential for significant errors of commission is low

  14. Safety related to the implantation of jugular catheters for haemodialysis and usefulness of PA chest X rays post procedure

    International Nuclear Information System (INIS)

    Restrepo, Cesar A; Chacon, Jose Arnob; Mauricio Villota, Duvan

    2007-01-01

    The objective is to determine how safe the implantation of transient double lumen jugular catheters is for hemodialysis in patients with renal disease, and who require dialysis therapy and Posterior Anterior (PA) chest X-Ray post procedure. Design: observational descriptive study. Site: renal units at RTS Ltda. Sucursal Caldas (Hospital Santa Sofia y Hospital Infantil Rafael Henao Toro de la Cruz Roja). Patients: all patients with renal disease in whom it was necessary to do hemodyalitic therapy with implantation of a jugular catheter, with medical records of the events and complications that occurred during the procedure, with subsequent control AP chest X Ray and that showed reports made by the radiologist or physician who carried out the procedure, about the findings in the chest X Ray. Patients with renal disease, in whom jugular catheters had been inserted: Methods: variables such as age, gender, race, body mass index (BMI) etiology of the renal failure,time of evolution of the disease, indications for insertion, priority of catheter insertion, type of catheter inserted, amount of punctures, physician who carried out the procedure and patient's co-morbidities were analyzed. The events considered as complicated were analyzed as well as if there was any relationship with co-morbidities and the analyzed variables. Findings in the PA chest X-Ray were recorded and their relationship with the difficulties encountered during the procedure. A bi-variance analysis was done. The dependent and independent variables were classified in the nominal measurement scale. Results: 774 clinical histories were reviewed. 562 were excluded due to lack of variables and impossibility to read the notes. Men older than de 55 (45,7%). 212 (97.1%) patients with diagnosis of chronic renal disease (CRD) and in whom 238 procedures were carried out. seven patients (2,85%) had acute renal failure (ARF). The fi rst indication for central catheter insertion was in patients with chronic uremia

  15. MELCOR computer code manuals

    Energy Technology Data Exchange (ETDEWEB)

    Summers, R.M.; Cole, R.K. Jr.; Smith, R.C.; Stuart, D.S.; Thompson, S.L. [Sandia National Labs., Albuquerque, NM (United States); Hodge, S.A.; Hyman, C.R.; Sanders, R.L. [Oak Ridge National Lab., TN (United States)

    1995-03-01

    MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. MELCOR is being developed at Sandia National Laboratories for the U.S. Nuclear Regulatory Commission as a second-generation plant risk assessment tool and the successor to the Source Term Code Package. A broad spectrum of severe accident phenomena in both boiling and pressurized water reactors is treated in MELCOR in a unified framework. These include: thermal-hydraulic response in the reactor coolant system, reactor cavity, containment, and confinement buildings; core heatup, degradation, and relocation; core-concrete attack; hydrogen production, transport, and combustion; fission product release and transport; and the impact of engineered safety features on thermal-hydraulic and radionuclide behavior. Current uses of MELCOR include estimation of severe accident source terms and their sensitivities and uncertainties in a variety of applications. This publication of the MELCOR computer code manuals corresponds to MELCOR 1.8.3, released to users in August, 1994. Volume 1 contains a primer that describes MELCOR`s phenomenological scope, organization (by package), and documentation. The remainder of Volume 1 contains the MELCOR Users Guides, which provide the input instructions and guidelines for each package. Volume 2 contains the MELCOR Reference Manuals, which describe the phenomenological models that have been implemented in each package.

  16. MELCOR computer code manuals

    International Nuclear Information System (INIS)

    Summers, R.M.; Cole, R.K. Jr.; Smith, R.C.; Stuart, D.S.; Thompson, S.L.; Hodge, S.A.; Hyman, C.R.; Sanders, R.L.

    1995-03-01

    MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. MELCOR is being developed at Sandia National Laboratories for the U.S. Nuclear Regulatory Commission as a second-generation plant risk assessment tool and the successor to the Source Term Code Package. A broad spectrum of severe accident phenomena in both boiling and pressurized water reactors is treated in MELCOR in a unified framework. These include: thermal-hydraulic response in the reactor coolant system, reactor cavity, containment, and confinement buildings; core heatup, degradation, and relocation; core-concrete attack; hydrogen production, transport, and combustion; fission product release and transport; and the impact of engineered safety features on thermal-hydraulic and radionuclide behavior. Current uses of MELCOR include estimation of severe accident source terms and their sensitivities and uncertainties in a variety of applications. This publication of the MELCOR computer code manuals corresponds to MELCOR 1.8.3, released to users in August, 1994. Volume 1 contains a primer that describes MELCOR's phenomenological scope, organization (by package), and documentation. The remainder of Volume 1 contains the MELCOR Users Guides, which provide the input instructions and guidelines for each package. Volume 2 contains the MELCOR Reference Manuals, which describe the phenomenological models that have been implemented in each package

  17. Selection methodology for LWR safety R and D programs and proposals. Volume III. User's manual for the multi-attribute utility package (MAUP)

    International Nuclear Information System (INIS)

    Hale, M.; Turnage, J.J.; Husseiny, A.A.; Ritzman, R.L.

    1981-02-01

    The computer program which was developed to apply the multi-attribute utility (MAU) methodology to the selection of LWR safety R and D programs and proposals is described. An overview of the MAU method is presented, followed by a description of the steps incorporated in developing individual modules for use in the multi-attribute utility package (MAUP). Each module is described complete with usage information and an example of computer output

  18. Quality management manual for production of high quality cassava flour

    DEFF Research Database (Denmark)

    Dziedzoave, Nanam Tay; Abass, Adebayo Busura; Amoa-Awua, Wisdom K.

    The high quality cassava flour (HQCF) industry has just started to evolve in Africa and elsewhere. The sustainability of the growing industry, the profitability of small- and medium-scale enterprises (SMEs) that are active in the industry and good-health of consumers can best be guaranteed through...... the adoption of proper quality and food safety procedures. Cassava processing enterprises involved in the productionof HQCF must therefore be commited to the quality and food safety of the HQCF. They must have the right technology, appropriate processing machhinery, standard testing instruments...... and the necessary technical expertise. This quality manual was therefore developed to guide small- to medium-scale cassava in the design and implematation of Hazard Analysis Critical Control Point (HACCP) system and Good manufacturing Practices (GMP) plans for HQCF production. It describes the HQCF production...

  19. Safety and efficacy of immediate postoperative feeding and bowel stimulation to prevent ileus after major gynecologic surgical procedures.

    Science.gov (United States)

    Fanning, James; Hojat, Rod

    2011-08-01

    Postoperative ileus is a major complication of abdominal surgical procedures To evaluate the incidence of ileus and gastrointestinal morbidity in patients who received immediate postoperative feeding and bowel stimulation after undergoing major gynecologic surgical procedures. During a 5-year period, the authors tracked demographic, surgical outcome, and follow-up information for 707 patients who underwent major gynecologic operations. All patients received the same postoperative orders, including immediate feeding of a diet of choice and bowel stimulation with 30 mL of magnesium hydroxide (milk of magnesia) twice daily until bowel movements occurred. Of 707 patients, 6 (<1%) had postoperative ileus. No patients experienced postoperative bowel obstruction and 2 patients (0.3%) had postoperative intestinal leak. No serious adverse effects associated with bowel stimulation were reported. Immediate postoperative feeding and bowel stimulation is a safe and effective approach to preventing ileus in patients who undergo major gynecologic surgical procedures.

  20. Structural integrity and its role in nuclear safety: recent UK advances in the development of high temperature design procedures

    International Nuclear Information System (INIS)

    Townley, C.H.A.

    1996-01-01

    This paper takes the liquid metal fast breeder reactor as an example and identifies those topics where research has had a role to play in providing improved design rules. Many of the previously adopted procedures contained large amounts of pessimism to allow for uncertainties in the prediction of long-term structural behaviour. The aim has therefore been to gain an improved physical insight into the phenomena which govern performance and to develope less restrictive procedures which, at the same time, guarantee the high standards of integrity which are required. (orig.)

  1. Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management. Rules of procedure and financial rules

    International Nuclear Information System (INIS)

    2002-01-01

    At the Preparatory Meeting of the Contracting Parties to the Joint Convention held from 10 to 12 December 2001, three documents were adopted concerning the rules and arrangements for conducting meetings of Contracting Parties to the Convention. As announced in the Report on the Preparatory Meeting (GOV/INF/2002/3), these three documents are being made available as INFCIRCs. Accordingly, herewith attached are the Rules of Procedure and Financial Rules. Also being made available are Guidelines regarding the Review Process (INFCIRC/603) and Guidelines regarding the Form and Structure of National Reports (INFCIRC/604)

  2. Aims and procedures used for the evaluation of research results in the field of nuclear safety with regard to the application of the Atomic Energy Law. Vol. 1

    International Nuclear Information System (INIS)

    Adomat, B.

    1985-01-01

    The purpose of this review, being executed for the Minister of the Interior of the German Federal Republic is to inform all parties involved in the licensing procedure as well as the consulting councils on the newest nuclear safety research results and the status of their verification in a precise, short manner. In addition experts opinions are given with regard to the relevance of these research results to nuclear rules and guidelines as well as to the execution of the Atomic Law. Each report is a short evaluation of a final research report. These evaluations are executed by specialists, who are acquainted with the technical aspects of the licensing procedure of nuclear power plants in the German Federal Republic. (orig.) [de

  3. Assessment of dietary intake of flavouring substances within the procedure for their safety evaluation: advantages and limitations of estimates obtained by means of a per capita method.

    Science.gov (United States)

    Arcella, D; Leclercq, C

    2005-01-01

    The procedure for the safety evaluation of flavourings adopted by the European Commission in order to establish a positive list of these substances is a stepwise approach which was developed by the Joint FAO/WHO Expert Committee on Food Additives (JECFA) and amended by the Scientific Committee on Food. Within this procedure, a per capita amount based on industrial poundage data of flavourings, is calculated to estimate the dietary intake by means of the maximised survey-derived daily intake (MSDI) method. This paper reviews the MSDI method in order to check if it can provide conservative intake estimates as needed at the first steps of a stepwise procedure. Scientific papers and opinions dealing with the MSDI method were reviewed. Concentration levels reported by the industry were compared with estimates obtained with the MSDI method. It appeared that, in some cases, these estimates could be orders of magnitude (up to 5) lower than those calculated considering concentration levels provided by the industry and regular consumption of flavoured foods and beverages. A critical review of two studies which had been used to support the statement that MSDI is a conservative method for assessing exposure to flavourings among high consumers was performed. Special attention was given to the factors that affect exposure at high percentiles, such as brand loyalty and portion sizes. It is concluded that these studies may not be suitable to validate the MSDI method used to assess intakes of flavours by European consumers due to shortcomings in the assumptions made and in the data used. Exposure assessment is an essential component of risk assessment. The present paper suggests that the MSDI method is not sufficiently conservative. There is therefore a clear need for either using an alternative method to estimate exposure to flavourings in the procedure or for limiting intakes to the levels at which the safety was assessed.

  4. Uranium tailings sampling manual

    International Nuclear Information System (INIS)

    Feenstra, S.; Reades, D.W.; Cherry, J.A.; Chambers, D.B.; Case, G.G.; Ibbotson, B.G.

    1985-01-01

    The purpose of this manual is to describe the requisite sampling procedures for the application of uniform high-quality standards to detailed geotechnical, hydrogeological, geochemical and air quality measurements at Canadian uranium tailings disposal sites. The selection and implementation of applicable sampling procedures for such measurements at uranium tailings disposal sites are complicated by two primary factors. Firstly, the physical and chemical nature of uranium mine tailings and effluent is considerably different from natural soil materials and natural waters. Consequently, many conventional methods for the collection and analysis of natural soils and waters are not directly applicable to tailings. Secondly, there is a wide range in the physical and chemical nature of uranium tailings. The composition of the ore, the milling process, the nature of tailings depositon, and effluent treatment vary considerably and are highly site-specific. Therefore, the definition and implementation of sampling programs for uranium tailings disposal sites require considerable evaluation, and often innovation, to ensure that appropriate sampling and analysis methods are used which provide the flexibility to take into account site-specific considerations. The following chapters describe the objective and scope of a sampling program, preliminary data collection, and the procedures for sampling of tailings solids, surface water and seepage, tailings pore-water, and wind-blown dust and radon

  5. Stirling engine design manual

    Science.gov (United States)

    Martini, W. R.

    1978-01-01

    This manual is intended to serve both as an introduction to Stirling engine analysis methods and as a key to the open literature on Stirling engines. Over 800 references are listed and these are cross referenced by date of publication, author and subject. Engine analysis is treated starting from elementary principles and working through cycles analysis. Analysis methodologies are classified as first, second or third order depending upon degree of complexity and probable application; first order for preliminary engine studies, second order for performance prediction and engine optimization, and third order for detailed hardware evaluation and engine research. A few comparisons between theory and experiment are made. A second order design procedure is documented step by step with calculation sheets and a worked out example to follow. Current high power engines are briefly described and a directory of companies and individuals who are active in Stirling engine development is included. Much remains to be done. Some of the more complicated and potentially very useful design procedures are now only referred to. Future support will enable a more thorough job of comparing all available design procedures against experimental data which should soon be available.

  6. Safety evaluation of the mixture of chemicals at a specific workplace : theoretical considerations and a suggested two-step procedure

    NARCIS (Netherlands)

    Feron, V.J.; Woutersen, R.A.; Arts, J.H.E.; Cassee, F.R.; Vrijer, F. de; Bladeren, P.J. van

    1995-01-01

    Procedures for the selection of compounds with high health hazard potential are reviewed, and major aspects of the assessment of health risks associated with exposure to mixtures of chemicals are discussed. Examples are given of additivity and synergism of effects following exposure to mixtures.

  7. Common handling procedures conducted in preclinical safety studies result in minimal hepatic gene expression changes in Sprague-Dawley rats.

    Directory of Open Access Journals (Sweden)

    Yudong D He

    Full Text Available Gene expression profiling is a tool to gain mechanistic understanding of adverse effects in response to compound exposure. However, little is known about how the common handling procedures of experimental animals during a preclinical study alter baseline gene expression. We report gene expression changes in the livers of female Sprague-Dawley rats following common handling procedures. Baseline gene expression changes identified in this study provide insight on how these changes may affect interpretation of gene expression profiles following compound exposure. Rats were divided into three groups. One group was not subjected to handling procedures and served as controls for both handled groups. Animals in the other two groups were weighed, subjected to restraint in Broome restrainers, and administered water via oral gavage daily for 1 or 4 days with tail vein blood collections at 1, 2, 4, and 8 hours postdose on days 1 and 4. Significantly altered genes were identified in livers of animals following 1 or 4 days of handling when compared to the unhandled animals. Gene changes in animals handled for 4 days were similar to those handled for 1 day, suggesting a lack of habituation. The altered genes were primarily immune function related genes. These findings, along with a correlating increase in corticosterone levels suggest that common handling procedures may cause a minor immune system perturbance.

  8. Recommendations: Procedure to develop a preliminary safety report as part of the radioactive waste repository construction licensing process

    International Nuclear Information System (INIS)

    2003-01-01

    The structure of a preliminary safety report for the title purpose should be as follows: A. Textual part: 1. General (Introduction, Basic information about the construction, Timetable); 2. Site information (Siting, Geography and demography, Meteorology and climatic situation, Hydrology, Geology and hydrogeology); 3. Repository design description (Basic function and performance requirements, Design, Auxiliary systems, Fire prevention/protection, Emergency plans); 4. Operation of the repository (Waste acceptance and inspection, Waste handling and interim storage, Waste disposal, Operating monitoring), 5. Health and environmental impact assessment (Radionuclide inventory, Radionuclide transport paths and mechanisms of release into the environment, Radionuclide release in normal and emergency situations, Radiation protection - health impact assessment and regulatory compliance, Draft operating limits and conditions, Proposed ways of assuring physical protection, Uncertainty assessment), 6. Safe repository shutdown/decommissioning concept, 7 Quality assurance assessment, 8. List of selected equipment. B. Annexes: Maps, Drawings, Diagrams, Miscellaneous; C. Documentation: Previous safety report amendments, Protocols, Miscellaneous. (P.A.)

  9. CALENDF-2010: user manual

    International Nuclear Information System (INIS)

    Sublet, Jean-Christophe; Ribon, Pierre; Coste-Delclaux, Mireille

    2011-09-01

    CALENDF-2010 represents a Fortran-95 update of the 1994, 2001 then 2005 code distribution with emphasise on programming quality and standards, physics and usage improvements. Devised to process multigroup cross-sections it relies on Gauss quadrature mathematical principle and strength. The followings processes can be handled by the code: moment probability table and effective cross-section calculation; pointwise cross section, probability table and effective cross-section regrouping; probability table condensation; probability table mix for several isotopes; probability table interpolation; effective cross section based probability table calculations; probability table calculations from effective cross-sections; cross-section comparison, complete energy pointwise cross-section processing and thickness dependent averaged transmission sample calculation. The CALENDF user manual, after having listed all principal code functions, describes sequentially each of them and gives comments on their associated output streams. Installation procedures, test cases and running time platform comparisons are given in the appendix. (authors)

  10. Multi-canister overpack operations and maintenance manual

    International Nuclear Information System (INIS)

    PIERCE, S.R.

    1999-01-01

    This manual provides general operating and maintenance instructions for the Multi-Canister Overpack. Procedure outlines included are conceptual in nature and will be modified, expanded, and refined during preparation of detailed operating procedures

  11. Ziptrack manual

    International Nuclear Information System (INIS)

    Ito, A.; Bosworth, W.; Rutherford, J.; Lynch, A.; Tung, L.; Yang, W.

    1983-07-01

    A phenolic cart holding 3 mutually perpendicular search coils is moved through an luminum beam into the magnetic field. Coil voltages re integrated and digitized through a Data Translation 1712 ADC. The cart is controlled and the data is processed by an on-line PDP-11/05 computer. The results are displayed on a Tektronix 4010 terminal, stored on 9 track, 800 bpi tapes, and optionally recorded on a hard copy. Software on a floppy disk controls the system. The position of the cart is located by an encoder and is checked along the beam line by optical switches. One encoder count equals 0.01945 in.. The X and Y positions are changed by manipulators at each end of the beam. 625 horizontal or 500 vertical counts equal 1 in.. The desired field mapping can be automatically set up by programming a grid of encoder counts on the ''SHOW STATUS'' chart. A ziptrack command summary is given. Following that is a typical procedure for ziptrack operations. Also attached are time constants for the integrators and coil calibrations for 30 ft. and 100 ft. long cables

  12. Operation manual for the INEL on-line mass-separator facility

    International Nuclear Information System (INIS)

    Anderl, R.A.

    1984-06-01

    This report is an operation manual for an on-line mass-separator facility which is located in Building 661 at the Test Reactor Area of the Idaho National Engineering Laboratory. The facility provides mass-separated sources of short-lived fission-product radionuclides whose decay properties can be studied using a variety of nuclear spectroscopic techniques. This facility is unique in that it utilizes the gas-jet technique to transport fission products from a 252 Cf source located in a hot cell to the ion source of the mass separator. This document includes the following: (a) a detailed description of the facility, (b) identification of equipment hazards and safety controls, (c) detailed operating procedures for startup, continuous operation and shutdown, (d) operating procedures for the californium hot cell, and (e) an operator's manual for the automated moving tape collector/data acquisition system. 7 references, 16 figures, 8 tables

  13. Facilitating Navigation in Quality Manuals by Providing Bookmarks or Similar

    International Nuclear Information System (INIS)

    Shaharum bin Ramli

    2012-01-01

    Nuclear Malaysia level quality manuals need to be shared with all divisions. A manual is usually distributed in the form of an electronic document that contains all procedures. Navigation from one heading or procedure to another should be facilitated by providing bookmarks or similar. This paper shows how to do it for Microsoft Word and PDF documents. (author)

  14. Janus neodymium glass laser operations manual

    International Nuclear Information System (INIS)

    Auerbach, J.M.; Holmes, N.C.; Trainor, R.J.

    1978-01-01

    A manual, prepared to guide personnel in operating and maintaining the Janus glass laser system, is presented. System components are described in detail. Step-by-step procedures are presented for firing the laser and for performing routine maintenance and calibration procedures

  15. Interlibrary Loan Communications Subsystem: Users Manual.

    Science.gov (United States)

    OCLC Online Computer Library Center, Inc., Dublin, OH.

    The OCLC Interlibrary Loan (ILL) Communications Subsystem provides participating libraries with on-line control of ILL transactions. This user manual includes a glossary of terms related to the procedures in using the system. Sections describe computer entry, searching, loan request form, loan response form, ILL procedures, the special message…

  16. Quality management for nuclear power plant operation: A manual

    International Nuclear Information System (INIS)

    1990-01-01

    The experience from well operated nuclear power plants shows that achievement of safe, reliable and economic performance is closely related to a strong commitment and involvement by the management personnel. A system of controls is necessary to ensure that satisfactory quality in operation is achieved and maintained over the long term. The key to achieving and assuring quality lies in the ability of management to define performance objectives and to ensure that significant safety and reliability problems are prevented or detected early and resolved. This Manual has been developed by the IAEA to assist plant managers in fulfilling their responsibility with regard to the control and direction of quality and of quality assurance activities in nuclear power plant operation. It emphasizes quality objectives for nuclear power plant operation and indicates the way in which a quality system based on quality assurance principles as established in the IAEA NUSS documents can be used by managers to accomplish these objectives. Since the Manual is mainly directed at management personnel, it is presented in the form of short highlighted practices complemented by typical examples of forms and procedures. Since not all the activities under the heading of quality in operation could be covered in a single document, the activities selected for this Manual comprise those where it was felt that practical advice is generally needed. A pragmatic document useful for direct application by plant managers was the envisaged objective

  17. Structural integrity and its role in nuclear safety recent UK developments in the development of high temperature design procedures

    International Nuclear Information System (INIS)

    Townley, C.H.A.

    1991-01-01

    The structural design rules for the reactors which operate at high temperature are not yet well developed. There is not difficulty in producing the plants which meet the high standards required by nuclear industry. However, there are the issues to be resolved which are associated with the deterioration of components in service, in order to achieve the optimum use of materials and the reduction of capital costs. The safety of plants is not at risk since any deterioration is detected by in-service monitoring, nevertheless, there would be severe economic penalty, if a plant must be retired prematurely because the continuing safety could not be demonstrated. In this paper, a liquid metal fast breeder reactor is taken up as an example, and the topics in which research plays a role for providing improved design rules are identified. Shakedown interaction diagrams, the methods of analysis based on shakedown, inelastic analysis and constitutive equations, creep fatigue damage and thermal shock, thermal striping, welds, defect assessment and so on are discussed. (K.I.)

  18. Assessment of LANL transportation policies and procedures

    International Nuclear Information System (INIS)

    Danna, J.G.; Jennrich, E.A.; Lund, D.M.; Davis, K.D.; Hoevemeyer, S.S.

    1991-04-01

    In order to determine whether activities related to the transportation of waste at Los Alamos National Laboratory (LANL) were being conducted in accordance with DOE policy, requirements stated in applicable DOE Orders were reviewed and compared with LANL policies and procedures described in the Administrative Requirements and the On-Site Transportation Manual. The following DOE Orders were determined to pertain to waste transportation and thus reviewed to identify requirements for which LANL is responsible for satisfying: Order 5820.2A Radioactive Waste Management; Order 1540.1 Materials Transportation and Traffic Management; and Order 5480.3 Safety Requirements for the Packaging and Transportation of Hazardous Materials, Hazardous Substances, and Hazardous Wastes. The LANL On-Site Transportation Manual and the Administrative Requirements contained in the LANL Environment, Safety, and Health Manual were reviewed to verify that each of the requirements identified through the review of the Orders and 10 CFR Part 71 were being satisfied. The following Administrative Requirements were considered in this task: Shipment of Radioactive Materials; Radioactive Liquid Waste; Low-Level Radioactive Solid Waste; Chemical, Hazardous, and Mixed Waste; Polychlorinated Biphenyls; and Transuranic (TRU) Solid Waste

  19. Estudo experimental sobre a eficiência e segurança da manobra de hiperinsuflação manual como técnica de remoção de secreção Experimental study on the efficiency and safety of the manual hyperinflation maneuver as a secretion clearance technique

    Directory of Open Access Journals (Sweden)

    Tatiana de Arruda Ortiz

    2013-04-01

    Full Text Available OBJETIVO: Avaliar, em um modelo pulmonar simulando um paciente sob ventilação mecânica, a eficiência e a segurança da manobra de hiperinsuflação manual (HM com o intuito de remover secreção pulmonar. MÉTODOS: Oito fisioterapeutas utilizaram um ressuscitador manual autoinflável para realizar HM com o objetivo de remover secreções, em duas condições: conforme rotineiramente aplicada durante sua prática clínica, e após receberem instruções verbais baseadas em recomendações de especialistas. Três cenários clínicos foram simulados: função pulmonar normal, doença pulmonar restritiva e doença pulmonar obstrutiva. RESULTADOS: Antes da instrução, o uso de duas compressões sequenciais do ressuscitador era comum, e a pressão proximal (Pprox foi mais alta em relação à obtida após a instrução. Entretanto, a pressão alveolar (Palv nunca excedeu 42,5 cmH2O (mediana, 16,1; intervalo interquartil [IQ], 11,7-24,5, mesmo com valores de Pprox de até 96,6 cmH2O (mediana, 36,7; IQ, 22,9-49,4. O volume corrente (VC gerado foi relativamente pequeno (mediana, 640 mL; IQ, 505-735 e o pico de fluxo inspiratório (PFI geralmente excedeu o pico de fluxo expiratório (PFE: 1,37 L/s (IQ, 0,99-1,90 e 1,01 L/s (IQ, 0,55-1,28, respectivamente. Uma relação PFI/PFE OBJECTIVE: To evaluate, in a lung model simulating a mechanically ventilated patient, the efficiency and safety of the manual hyperinflation (MH maneuver as a means of removing pulmonary secretions. METHODS: Eight respiratory therapists (RTs were asked to use a self-inflating manual resuscitator on a lung model to perform MH as if to remove secretions, under two conditions: as routinely applied during their clinical practice; and after receiving verbal instructions based on expert recommendations. In both conditions, three clinical scenarios were simulated: normal lung function, restrictive lung disease, and obstructive lung disease. RESULTS: Before instruction, it was common

  20. Safety handbook

    International Nuclear Information System (INIS)

    1990-01-01

    The purpose of the Australian Nuclear Science and Technology Organization's Safety Handbook is to outline simply the fundamental procedures and safety precautions which provide an appropriate framework for safe working with any potential hazards, such as fire and explosion, welding, cutting, brazing and soldering, compressed gases, cryogenic liquids, chemicals, ionizing radiations, non-ionising radiations, sound and vibration, as well as safety in the office. It also specifies the organisation for safety at the Lucas Heights Research Laboratories and the responsibilities of individuals and committees. It also defines the procedures for the scrutiny and review of all operations and the resultant setting of safety rules for them. ills

  1. Development on inspection and recognition procedure of clearance level of radioactivity in metal wastes, to secure social safety for reused metals

    International Nuclear Information System (INIS)

    Hattori, Takatoshi

    2002-01-01

    The Central Research Institute of Electric Power Industry developed a new procedure automatically measurable on radioactivity level in metal wastes in high precision by using the newest three-dimensional (3D) shape measuring technology and 3D Monte-Carlo computing technology (a code to probabilistically compute formation and movement of gamma-ray from metal wastes to detectors) to contribute to inspection and recognition of clearance level of radioactivity. This procedure can prove no super micro amount of radioactivity of 250 Bq in metal wastes of testing objects. As this proof is an evaluation of conservative safety side showing no pollution at any 100 sq cm of surface of the metal wastes on considering for taking-out reference on matters, for its price, the procedure cancelled all of labors to test all of metal wastes surfaces by survey meter, and so on, and feasibility of overlook of pollution at places difficult to measure by using survey meters can perfectly excluded. Its practical tester is planned to produce at 2002 fiscal year, and testing performance against actual metal wastes is planned to confirm by its proof-test on 2003 to 2004 fiscal years. (G.K.)

  2. Manual of radioisotope production

    International Nuclear Information System (INIS)

    1966-01-01

    The Manual of Radioisotope Production has been compiled primarily to help small reactor establishments which need a modest programme of radioisotope production for local requirements. It is not comprehensive, but gives guidance on essential preliminary considerations and problems that may be met in the early stages of production. References are included as an aid to the reader who wishes to seek further in the extensive literature on the subject. In preparing the Manual, which is in two parts, the Agency consulted several Member States which already have long experience in radioisotope production. An attempt has been made to condense this experience, firstly, by setting out the technical and economic considerations which govern the planning and execution of an isotope programme and, secondly, by providing experimental details of isotope production processes. Part I covers topics common to all radioisotope processing, namely, laboratory design, handling and dispensing of radioactive solutions, quality control, measurement and radiological safety. Part II contains information on the fifteen radioisotopes in most common use. These are bromine-82, cobalt-58, chromium-51, copper-64, fluorine-18, gold-198, iodine-131, iron-59, magnesium-28, potassium-42, sodium-24, phosphorus-32, sulphur-35, yttrium-90 and zinc-65. Their nuclear properties are described, references to typical applications are given and published methods of production are reviewed; also included are descriptions in detail of the production processes used at several national atomic energy organizations. No attempt has been made to distinguish the best values for nuclear data or to comment on the relative merits of production processes. Each process is presented essentially as it was described by the contributor on the understanding that critical comparisons are not necessary for processes which have been well tried in practical production for many years. The information is presented as a guide to enable

  3. User's manual of Tokamak Simulation Code

    International Nuclear Information System (INIS)

    Nakamura, Yukiharu; Nishino, Tooru; Tsunematsu, Toshihide; Sugihara, Masayoshi.

    1992-12-01

    User's manual for use of Tokamak Simulation Code (TSC), which simulates the time-evolutional process of deformable motion of axisymmetric toroidal plasma, is summarized. For the use at JAERI computer system, the TSC is linked with the data management system GAEA. This manual is forcused on the procedure for the input and output by using the GAEA system. Model equations to give axisymmetric motion, outline of code system, optimal method to get the well converged solution are also described. (author)

  4. Simplified operation manual PA-720 particle counter

    International Nuclear Information System (INIS)

    Draper, V.F.

    1980-01-01

    The model PA-720 Automatic Particle Size Analyzer is a simple, relatively high speed device designed to provide accurate size distributions in both tabular and graphic forms. This model has two dynamic ranges; 50 to 2500 microns and 200 to 1600 microns. This is an abbreviated version of the manufacturer's operating manual. It provides all the necessary information for the novice and experienced user. For more detailed explanations and servicing procedures one should reference the full manual

  5. PFP MICON maintenance manual. Revision 1

    International Nuclear Information System (INIS)

    Silvan, G.R.

    1995-01-01

    This manual covers the use of maintenance displays, maintenance procedures, system alarms and common system failures. This manual is intended to supplement the MICON maintenance training not replace it. It also assumes that the user is familiar with the normal operation of the MICON A/S system. The MICON system is a distributed control computer and, among other things, controls the HVAC system for the Plutonium Finishing Plant

  6. L-059: EPR-First responders: Radiological emergency manual for first responders

    International Nuclear Information System (INIS)

    2011-01-01

    This conference is an emergency manual review about the first responders knowledge. The IAEA safety standard manuals, the medical gestion, the security forces and the fast communications are very important in a radiological emergency

  7. Rules and procedures for the design and operation of hazardous research equipment

    International Nuclear Information System (INIS)

    1978-12-01

    The manual has been prepared for use by research personnel involved in experiments at the Lawrence Berkeley Laboratory. It contains rules and procedures for the design, test, installation, and operation of hazardous research equipment. Sect. I contains such information as responsibility of experimenters for safety, descriptions of the various Laboratory safety organizations, and enumeration of various services available to experimenters at the Laboratory. Sect. II describes specific rules for the setup and operation of experimental equipment at the Laboratory. Sect. III gives detailed design criteria and procedures for equipment frequently encountered in the high energy physics laboratory

  8. A Manual of Style.

    Science.gov (United States)

    Nebraska State Dept. of Education, Lincoln.

    This "Manual of Style" is offered as a guide to assist Nebraska State employees in producing quality written communications and in presenting a consistently professional image of government documents. The manual is not designed to be all-inclusive. Sections of the manual discuss formatting documents, memorandums, letters, mailing…

  9. Manual for reactor produced radioisotopes

    International Nuclear Information System (INIS)

    2003-01-01

    Radioisotopes find extensive applications in several fields including medicine, industry, agriculture and research. Radioisotope production to service different sectors of economic significance constitutes an important ongoing activity of many national nuclear programmes. Radioisotopes, formed by nuclear reactions on targets in a reactor or cyclotron, require further processing in almost all cases to obtain them in a form suitable for use. Specifications for final products and testing procedures for ensuring quality are also an essential part of a radioisotope production programme. The International Atomic Energy Agency (IAEA) has compiled and published such information before for the benefit of laboratories of Member States. The first compilation, entitled Manual of Radioisotope Production, was published in 1966 (Technical Reports Series No. 63). A more elaborate and comprehensive compilation, entitled Radioisotope Production and Quality Control, was published in 1971 (Technical Reports Series No. 128). Both served as useful reference sources for scientists working in radioisotope production worldwide. The 1971 publication has been out of print for quite some time. The IAEA convened a consultants meeting to consider the need for compiling an updated manual. The consultants recommended the publication of an updated manual taking the following into consideration: significant changes have taken place since 1971 in many aspects of radioisotope production; many radioisotopes have been newly introduced while many others have become gradually obsolete; considerable experience and knowledge have been gained in production of important radioisotopes over the years, which can be preserved through compilation of the manual; there is still a need for a comprehensive manual on radioisotope production methods for new entrants to the field, and as a reference. It was also felt that updating all the subjects covered in the 1971 manual at a time may not be practical considering the

  10. Procedures for treating common cause failures in safety and reliability studies: Volume 2, Analytic background and techniques: Final report

    International Nuclear Information System (INIS)

    Mosleh, A.; Fleming, K.N.; Parry, G.W.; Paula, H.M.; Worledge, D.H.; Rasmuson, D.M.

    1988-12-01

    This report presents a framework for the inclusion of the impact of common cause failures in risk and reliability evaluations. Common cause failures are defined as that subset of dependent failures for which causes are not explicitly included in the logic model as basic events. The emphasis here is on providing procedures for a practical, systematic approach that can be used to perform and clearly document the analysis. The framework and the methods discussed for performing the different stages of the analysis integrate insights obtained from engineering assessments of the system and the historical evidence from multiple failure events into a systematic, reproducible, and defensible analysis. This document, Volume 2, contains a series of appendices that provide additional background and methodological detail on several important topics discussed in Volume 1

  11. Development of a procedure for qualitative and quantitative evaluation of human factors as a part of probabilistic safety assessments of nuclear power plants. Part B. Technical documentation

    International Nuclear Information System (INIS)

    Richei, A.

    1998-01-01

    As international studies have shown, accidents in plants are increasingly caused by combinations of technical failures and human errors. Therefore careful investigations of man-machine-interactions to determine human reliability are gaining importance worldwide. Regarding nuclear power plants such investigations are usually carried out within the scope of probabilistic safety assessments. A great number of procedures to evaluate human factors has been developed up to now. However, none of them is able to take into account the whole spectrum of requirements - as for instance transferability of date to other plants, analysis of weak points, and evaluation of cognitive tasks - for a complete and reliable probabilistic safety assessment. Based on an advanced model for a man-machine-system, the Human Error Rate Assessment and Optimizing System (HEROS) and a corresponding expert system of the same name are introduced. This expert system enables the quantification of human error probabilities for plant operator actions on the one hand and is also capable of providing quantitative statements regarding the optimization of man-machine-system in terms of human error probability minimization on the other one. Three relevant evaluation levels, i.e. 'Management Structure', 'Working Environment' and 'Man-Machine-Interface', are derived from a model of the man-machine-system. Linguistic variables are assigned to all performance shaping factors at these levels. These variables are used to establish a rule-based expert system. The knowledge bases of this system are represented by rules. Processing of these rules is carried out by means of the fuzzy set theory, after provision of relevant data for a particular personal action to be evaluated. This procedure enables a simple and effective use of ergonomic studies as the relevant database, which is also transferable to other plants with any design. The expert system consist in total of 16 rule bases in which all ascertainable and

  12. Comparative efficacy and safety of the left versus right radial approach for percutaneous coronary procedures: a meta-analysis including 6870 patients

    Directory of Open Access Journals (Sweden)

    S.L. Xia

    2015-08-01

    Full Text Available The radial approach is widely used in the treatment of patients with coronary artery disease. We conducted a meta-analysis of published results on the efficacy and safety of the left and right radial approaches in patients undergoing percutaneous coronary procedures. A systematic search of reference databases was conducted, and data from 14 randomized controlled trials involving 6870 participants were analyzed. The left radial approach was associated with significant reductions in fluoroscopy time [standardized mean difference (SMD=-0.14, 95% confidence interval (CI=-0.19 to -0.09; P<0.00001] and contrast volume (SMD=-0.07, 95%CI=-0.12 to -0.02; P=0.009. There were no significant differences in rate of procedural failure of the left and the right radial approaches [risk ratios (RR=0.98; 95%CI=0.77-1.25; P=0.88] or procedural time (SMD=-0.05, 95%CI=0.17-0.06; P=0.38. Tortuosity of the subclavian artery (RR=0.27, 95%CI=0.14-0.50; P<0.0001 was reported more frequently with the right radial approach. A greater number of catheters were used with the left than with the right radial approach (SMD=0.25, 95%CI=0.04-0.46; P=0.02. We conclude that the left radial approach is as safe as the right radial approach, and that the left radial approach should be recommended for use in percutaneous coronary procedures, especially in percutaneous coronary angiograms.

  13. Nuclear medicine resources manual

    International Nuclear Information System (INIS)

    2006-02-01

    Over the past decade many IAEA programmes have significantly enhanced the capabilities of numerous Member States in the field of nuclear medicine. Functional imaging using nuclear medicine procedures has become an indispensable tool for the diagnosis, treatment planning and management of patients. However, due to the heterogeneous growth and development of nuclear medicine in the IAEA's Member States, the operating standards of practice vary considerably from country to country and region to region. This publication is the result of the work of over 30 international professionals who have assisted the IAEA in the process of standardization and harmonization. This manual sets out the prerequisites for the establishment of a nuclear medicine service, including basic infrastructure, suitable premises, reliable supply of electricity, maintenance of a steady temperature, dust exclusion for gamma cameras and radiopharmacy dispensaries. It offers clear guidance on human resources and training needs for medical doctors, technologists, radiopharmaceutical scientists, physicists and specialist nurses in the practice of nuclear medicine. The manual describes the requirements for safe preparation and quality control of radiopharmaceuticals. In addition, it contains essential requirements for maintenance of facilities and instruments, for radiation hygiene and for optimization of nuclear medicine operational performance with the use of working clinical protocols. The result is a comprehensive guide at an international level that contains practical suggestions based on the experience of professionals around the globe. This publication will be of interest to nuclear medicine physicians, radiologists, medical educationalists, diagnostic centre managers, medical physicists, medical technologists, radiopharmacists, specialist nurses, clinical scientists and those engaged in quality assurance and control systems in public health in both developed and developing countries

  14. Manual for environmental radiological surveillance

    International Nuclear Information System (INIS)

    Sumiya, Shuichi; Matsuura, Kenichi; Nakano, Masanao; Takeyasu, Masanori; Morisawa, Masato; Onuma, Toshimitsu; Fujita, Hiroki; Mizutani, Tomoko; Watanabe, Hajime; Sugai, Masamitsu

    2010-03-01

    Environmental radiation monitoring around the Tokai Reprocessing Plant has been conducted by the Nuclear Fuel Cycle Engineering Laboratories, based on 'Safety Regulations for the Reprocessing Plant of JAEA, Chapter IV - Environmental monitoring' and Environmental Radiation Monitoring Program decided by the Ibaraki prefectural government. The radiation monitoring installations and equipments were also prepared for emergency. This manual describes; (1) the installations of radiological measurement, (2) the installations of meteorological observation, and (3) environmental data processing system for executing the terrestrial environmental monitoring by Environmental Protection Section, Radiation Protection Department. The environmental monitoring has been operated through the manual published in 1993 (PNC TN8520 93-001). Then the whole articles were revised because the partially of installations and equipments having been updated in recent years. (author)

  15. Generic procedures for assessment and response during a radiological emergency

    International Nuclear Information System (INIS)

    2000-08-01

    One of the most important aspects of managing a radiological emergency is the ability to promptly and adequately determine and take actions to protect members of the public and emergency workers. Radiological accident assessment must take account of all critical information available at any time and must be an iterative and dynamic process aimed at reviewing the response as more detailed and complete information becomes available. This manual provides the tools, generic procedures and data needed for an initial response to a non-reactor radiological accident. This manual is one out of a set of IAEA publications on emergency preparedness and response, including Method for the Development of Emergency Response Preparedness for Nuclear or Radiological Accidents (IAEA-TECDOC-953), Generic Assessment Procedures for Determining Protective Actions During a Reactor Accident (IAEA-TECDOC-955) and Intervention Criteria in a Nuclear or Radiation Emergency (Safety Series No. 109)

  16. Synoptic meteorology manual of standard practices

    Energy Technology Data Exchange (ETDEWEB)

    Jenne, D.E.

    1954-03-22

    This report, dated March 22, 1954 details work procedures for the 200- West Area at HAPO. Topics discussed include emergency procedures, safety and housekeeping practices, policies and procedures, instruments and equipment located at the 622 tower, instruments and equipment located offsite, observational procedures, form entries, and card punching, and weather forecasting.

  17. Machinery safety of lathe machine using SHARP-systemic human action reliability procedure: a pilot case study in academic laboratory

    Science.gov (United States)

    Suryoputro, M. R.; Sari, A. D.; Sugarindra, M.; Arifin, R.

    2017-12-01

    This research aimed to understand the human reliability analysis, to find the SHARP method with its functionality on case study and also emphasize the practice in Lathe machine, continued with identifying improvement that could be made to the existing safety system. SHARP comprises of 7 stages including definition, screening, breakdown, representation, impact assessment, quantification and documentation. These steps were combined and analysed using HIRA, FTA and FMEA. HIRA analysed the lathe at academic laboratory showed the level of the highest risk with a score of 9 for the activities of power transmission parts and a score of 6 for activities which shall mean the moving parts required to take action to reduce the level of risk. Hence, the highest RPN values obtained in the power transmission activities with a value of 18 in the power transmission and then the activities of moving parts is 12 and the activities of the operating point of 8. Thus, this activity has the highest risk of workplace accidents in the operation. On the academic laboratory the improvement made on the engineering control initially with a machine guarding and completed with necessary administrative controls (SOP, work permit, training and routine cleaning) and dedicated PPEs.

  18. An overview of the IAEA Safety Series on procedures for evaluating the reliability of predictions made by environmental transfer models

    International Nuclear Information System (INIS)

    Hoffman, F.W.; Hofer, E.

    1987-10-01

    The International Atomic Energy Agency is preparing a Safety Series publication on practical approaches for evaluating the reliability of the predictions made by environmental radiological assessment models. This publication identifies factors that affect the reliability of these predictions and discusses methods for quantifying uncertainty. Emphasis is placed on understanding the quantity of interest specified by the assessment question and distinguishing between stochastic variability and lack of knowledge about either the true value or the true distribution of values for quantity of interest. Among the many approaches discussed, model testing using independent data sets (model validation) is considered the best method for evaluating the accuracy in model predictions. Analytical and numerical methods for propagating the uncertainties in model parameters are presented and the strengths and weaknesses of model intercomparison exercises are also discussed. It is recognized that subjective judgment is employed throughout the entire modelling process, and quantitative reliability statements must be subjectively obtained when models are applied to different situations from those under which they have been tested. (6 refs.)

  19. Safety and Feasibility of a Ketamine Package to Support Emergency and Essential Surgery in Kenya when No Anesthetist is Available: An Analysis of 1216 Consecutive Operative Procedures.

    Science.gov (United States)

    Burke, Thomas F; Suarez, Sebastian; Sessler, Daniel I; Senay, Ayla; Yusufali, Taha; Masaki, Charles; Guha, Moytrayee; Rogo, Debora; Jani, Pankaj; Nelson, Brett D; Rogo, Khama

    2017-12-01

    Lack of access to emergency and essential surgery is widespread in low- and middle-income countries. Scarce anesthesia services contribute to this unmet need. The aim of this study was to evaluate the safety and feasibility of the Every Second Matters for Emergency and Essential Surgery-Ketamine (ESM-Ketamine) package for emergency and essential procedures when no anesthetist was available. From November 2013 to September 2017, the ESM-Ketamine package was used for patients requiring emergency or life-improving surgeries in fifteen selected facilities across Kenya when no anesthetist was available. A mixed-methods approach was used to assess safety and feasibility of the ESM-Ketamine package, including demand, acceptability, and practicality. The primary outcome was ketamine-related adverse events. Key-informant interviews captured perceptions of providers, hospital administrators, and surgeons/proceduralists. Non-anesthetist mid-level providers used ESM-Ketamine for 1216 surgical procedures across the fifteen study facilities. The median ketamine dose was 2.1 mg/kg. Brief (30 s) oxygen desaturations occurred in seven patients (0.6%). There were 157 (13%) reported cases of hallucinations and agitation which were treated with diazepam. All patients recovered uneventfully, and no ketamine-related deaths were reported. Twenty-seven key-informant interviews showed strong support for the program with four main themes: financial considerations, provision of services, staff impact, and scaling considerations. The ESM-Ketamine package appears safe and feasible and is capable of expanding access to emergency and essential surgeries in rural Kenya when no anesthetist is available.

  20. Efficacy, Reliability, and Safety of Completely Autologous Fibrin Glue in Neurosurgical Procedures: Single-Center Retrospective Large-Number Case Study.

    Science.gov (United States)

    Nakayama, Noriyuki; Yano, Hirohito; Egashira, Yusuke; Enomoto, Yukiko; Ohe, Naoyuki; Kanemura, Nobuhiro; Kitagawa, Junichi; Iwama, Toru

    2018-01-01

    Commercially available fibrin glue (Com-FG), which is used commonly worldwide, is produced with pooled human plasma from multiple donors. However, it has added bovine aprotinin, which involves the risk of infection, allogenic immunity, and allergic reactions. We evaluate the efficacy, reliability, and safety of completely autologous fibrin glue (CAFG). From August 2014 to February 2016, prospective data were collected and analyzed from 153 patients. CAFG was prepared with the CryoSeal System using autologous blood and was applied during neurosurgical procedures. Using CAFG-soaked oxidized regenerated cellulose and/or polyglycolic acid sheets, we performed a pinpoint hemostasis, transposed the offending vessels in a microvascular decompression, and covered the dural incision to prevent cerebrospinal fluid leakage. The CryoSeal System had generated up to a mean of 4.51 mL (range, 3.0-8.4 mL) of CAFG from 400 mL autologous blood. Com-FG products were not used in our procedures. Only 6 patients required an additional allogeneic blood transfusion. The hemostatic effective rate was 96.1% (147 of 153 patients). Only 1 patient who received transsphenoidal surgery for a pituitary adenoma presented with the complication of delayed postoperative cerebrospinal fluid leakage (0.65%). No patient developed allergic reactions or systemic complications associated with the use of CAFG. CAFG effectively provides hemostatic, adhesive, and safety performance. The timing and three-dimensional shape of CAFG-soaked oxidized regenerated cellulose and/or polyglycolic acid sheets solidification can be controlled with slow fibrin formation. The cost to prepare CAFG is similar compared with Com-FG products, and it can therefore be easily used at most institutions. Copyright © 2017 Elsevier Inc. All rights reserved.