Safety Design Approach for the Development of Safety Requirements for Design of Commercial HTGR

International Nuclear Information System (INIS)

Ohashi, Hirofumi; Sato, Hiroyuki; Nakagawa, Shigeaki; Tachibana, Yukio; Nishihara, Tetsuo; Yan, Xing; Sakaba, Nariaki; Kunitomi, Kazuhiko

2014-01-01

The research committee on “Safety requirements for HTGR design” was established in 2013 under the Atomic Energy Society of Japan to develop the draft safety requirements for the design of commercial High Temperature Gas-cooled Reactors (HTGRs), which incorporate the HTGR safety features demonstrated using the High Temperature Engineering Test Reactor (HTTR), lessons learned from the accident of Fukushima Daiichi Nuclear Power Station and requirements for the integration of the hydrogen production plants. The safety design approach for the commercial HTGRs which is a basement of the safety requirements is determined prior to the development of the safety requirements. The safety design approaches for the commercial HTGRs are to confine the radioactive materials within the coated fuel particles not only during normal operation but also during accident conditions, and the integrity of the coated fuel particles and other requiring physical barriers are protected by the inherent and passive safety features. This paper describes the main topics of the research committee, the safety design approaches and the safety functions of the commercial HTGRs determined in the research committee. (author)

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Chinese Ed.)

International Nuclear Information System (INIS)

2012-01-01

On the basis of the principles included in the Fundamental Safety Principles, IAEA Safety Standards Series No. SF-1, this Safety Requirements publication establishes requirements applicable to the design of nuclear power plants. It covers the design phase and provides input for the safe operation of the power plant. It elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (French Ed.)

International Nuclear Information System (INIS)

2012-01-01

On the basis of the principles included in the Fundamental Safety Principles, IAEA Safety Standards Series No. SF-1, this Safety Requirements publication establishes requirements applicable to the design of nuclear power plants. It covers the design phase and provides input for the safe operation of the power plant. It elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Arabic Ed.)

International Nuclear Information System (INIS)

2012-01-01

On the basis of the principles included in the Fundamental Safety Principles, IAEA Safety Standards Series No. SF-1, this Safety Requirements publication establishes requirements applicable to the design of nuclear power plants. It covers the design phase and provides input for the safe operation of the power plant. It elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Safety design features of the IRIS

International Nuclear Information System (INIS)

2009-01-01

The International Reactor Innovative and Secure (IRIS) is an advanced, integral, light water cooled reactor of medium generating capacity (335 MW(e)), that features an integral reactor vessel containing all the reactor primary system components, including steam generators, coolant pumps, pressurizer and heaters, and control rod drive mechanisms; in addition to the typical core, internals, control rods and neutron reflector. This integral configuration allows for the use of a small, high design pressure, spherical steel containment which results in a significant reduction in the size of the nuclear island. Other IRIS innovations include a simplified passive safety system concept and equipment features that derive from the 'safety-by-design' philosophy. This design approach allows for elimination of certain accident initiators at the design stage, or when outright elimination is not possible, decreases accident consequences and/or their probability of occurrence. Major design characteristics of the IRIS are given. As part of the IRIS pre-application licensing review by the U.S. Nuclear Regulatory Commission (NRC), the IRIS design team has developed a test plan that will provide the necessary data for safety analysis computer model verification, as well as for verifying the manufacturing feasibility, operability, and durability of new component designs

Aviation Safety Simulation Model

Science.gov (United States)

Houser, Scott; Yackovetsky, Robert (Technical Monitor)

2001-01-01

The Aviation Safety Simulation Model is a software tool that enables users to configure a terrain, a flight path, and an aircraft and simulate the aircraft's flight along the path. The simulation monitors the aircraft's proximity to terrain obstructions, and reports when the aircraft violates accepted minimum distances from an obstruction. This model design facilitates future enhancements to address other flight safety issues, particularly air and runway traffic scenarios. This report shows the user how to build a simulation scenario and run it. It also explains the model's output.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Spanish Edition)

International Nuclear Information System (INIS)

2012-01-01

This publication is a revision of Safety Requirements No. NS-R-1, Safety of Nuclear Power Plants: Design. It establishes requirements applicable to the design of nuclear power plants and elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. It will be useful for organizations involved in the design, manufacture, construction, modification, maintenance, operation and decommissioning of nuclear power plants, as well as for regulatory bodies. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Russian Edition)

International Nuclear Information System (INIS)

2012-01-01

This publication is a revision of Safety Requirements No. NS-R-1, Safety of Nuclear Power Plants: Design. It establishes requirements applicable to the design of nuclear power plants and elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. It will be useful for organizations involved in the design, manufacture, construction, modification, maintenance, operation and decommissioning of nuclear power plants, as well as for regulatory bodies. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Safety design requirements for safety systems and components of JSFR

International Nuclear Information System (INIS)

Kubo, Shigenobu; Shimakawa, Yoshio; Yamano, Hidemasa; Kotake, Shoji

2011-01-01

Safety design requirements for JSFR were summarized taking the development targets of the FaCT project and design feature of JSFR into account. The related safety principle and requirements for Monju, CRBRP, PRISM, SPX, LWRs, IAEA standards, goals of GIF, basic principle of INPRO etc. were also taken into account so that the safety design requirements can be a next-generation global standard. The development targets for safety and reliability are set based on those of FaCT, namely, ensuring safety and reliability equal to future LWR and related fuel cycle facilities. In order to achieve these targets, the defence-in-depth concept is used as the basic safety design principle. General features of the safety design requirements are 1) Achievement of higher reliability, 2) Achievement of higher inspectability and maintainability, 3) Introduction of passive safety features, 4) Reduction of operator action needs, 5) Design consideration against Beyond Design Basis Events, 6) In-Vessel Retention of degraded core materials, 7) Prevention and mitigation against sodium chemical reactions, and 8) Design against external events. The current specific requirements for each system and component are summarized taking the basic design concept of JSFR into account, which is an advanced loop-type large-output power plant with a mixed-oxide-fuelled core. (author)

Generic radiation safety design for SSRL synchrotron radiation beamlines

Energy Technology Data Exchange (ETDEWEB)

Liu, James C. [Radiation Protection Department, Stanford Linear Accelerator Center (SLAC), MS 48, P.O. Box 20450, Stanford, CA 94309 (United States)]. E-mail: james@slac.stanford.edu; Fasso, Alberto [Radiation Protection Department, Stanford Linear Accelerator Center (SLAC), MS 48, P.O. Box 20450, Stanford, CA 94309 (United States); Khater, Hesham [Radiation Protection Department, Stanford Linear Accelerator Center (SLAC), MS 48, P.O. Box 20450, Stanford, CA 94309 (United States); Prinz, Alyssa [Radiation Protection Department, Stanford Linear Accelerator Center (SLAC), MS 48, P.O. Box 20450, Stanford, CA 94309 (United States); Rokni, Sayed [Radiation Protection Department, Stanford Linear Accelerator Center (SLAC), MS 48, P.O. Box 20450, Stanford, CA 94309 (United States)

2006-12-15

To allow for a conservative, simple, uniform, consistent, efficient radiation safety design for all SSRL beamlines, a generic approach has been developed, considering both synchrotron radiation (SR) and gas bremsstrahlung (GB) hazards. To develop the methodology and rules needed for generic beamline design, analytic models, the STAC8 code, and the FLUKA Monte Carlo code were used to pre-calculate sets of curves and tables that can be looked up for each beamline safety design. Conservative beam parameters and standard targets and geometries were used in the calculations. This paper presents the SPEAR3 beamline parameters that were considered in the design, the safety design considerations, and the main pre-calculated results that are needed for generic shielding design. In the end, the rules and practices for generic SSRL beamline design are summarized.

Specification of advanced safety modeling requirements (Rev. 0).

Energy Technology Data Exchange (ETDEWEB)

Fanning, T. H.; Tautges, T. J.

2008-06-30

The U.S. Department of Energy's Global Nuclear Energy Partnership has lead to renewed interest in liquid-metal-cooled fast reactors for the purpose of closing the nuclear fuel cycle and making more efficient use of future repository capacity. However, the U.S. has not designed or constructed a fast reactor in nearly 30 years. Accurate, high-fidelity, whole-plant dynamics safety simulations will play a crucial role by providing confidence that component and system designs will satisfy established design limits and safety margins under a wide variety of operational, design basis, and beyond design basis transient conditions. Current modeling capabilities for fast reactor safety analyses have resulted from several hundred person-years of code development effort supported by experimental validation. The broad spectrum of mechanistic and phenomenological models that have been developed represent an enormous amount of institutional knowledge that needs to be maintained. Complicating this, the existing code architectures for safety modeling evolved from programming practices of the 1970s. This has lead to monolithic applications with interdependent data models which require significant knowledge of the complexities of the entire code in order for each component to be maintained. In order to develop an advanced fast reactor safety modeling capability, the limitations of the existing code architecture must be overcome while preserving the capabilities that already exist. To accomplish this, a set of advanced safety modeling requirements is defined, based on modern programming practices, that focuses on modular development within a flexible coupling framework. An approach for integrating the existing capabilities of the SAS4A/SASSYS-1 fast reactor safety analysis code into the SHARP framework is provided in order to preserve existing capabilities while providing a smooth transition to advanced modeling capabilities. In doing this, the advanced fast reactor safety models

Specification of advanced safety modeling requirements (Rev. 0)

International Nuclear Information System (INIS)

Fanning, T. H.; Tautges, T. J.

2008-01-01

The U.S. Department of Energy's Global Nuclear Energy Partnership has lead to renewed interest in liquid-metal-cooled fast reactors for the purpose of closing the nuclear fuel cycle and making more efficient use of future repository capacity. However, the U.S. has not designed or constructed a fast reactor in nearly 30 years. Accurate, high-fidelity, whole-plant dynamics safety simulations will play a crucial role by providing confidence that component and system designs will satisfy established design limits and safety margins under a wide variety of operational, design basis, and beyond design basis transient conditions. Current modeling capabilities for fast reactor safety analyses have resulted from several hundred person-years of code development effort supported by experimental validation. The broad spectrum of mechanistic and phenomenological models that have been developed represent an enormous amount of institutional knowledge that needs to be maintained. Complicating this, the existing code architectures for safety modeling evolved from programming practices of the 1970s. This has lead to monolithic applications with interdependent data models which require significant knowledge of the complexities of the entire code in order for each component to be maintained. In order to develop an advanced fast reactor safety modeling capability, the limitations of the existing code architecture must be overcome while preserving the capabilities that already exist. To accomplish this, a set of advanced safety modeling requirements is defined, based on modern programming practices, that focuses on modular development within a flexible coupling framework. An approach for integrating the existing capabilities of the SAS4A/SASSYS-1 fast reactor safety analysis code into the SHARP framework is provided in order to preserve existing capabilities while providing a smooth transition to advanced modeling capabilities. In doing this, the advanced fast reactor safety models will

Generalized railway tank car safety design optimization for hazardous materials transport: Addressing the trade-off between transportation efficiency and safety

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Barkan, Christopher P.L.

2011-01-01

North America railways offer safe and generally the most economical means of long distance transport of hazardous materials. Nevertheless, in the event of a train accident releases of these materials can pose substantial risk to human health, property or the environment. The majority of railway shipments of hazardous materials are in tank cars. Improving the safety design of these cars to make them more robust in accidents generally increases their weight thereby reducing their capacity and consequent transportation efficiency. This paper presents a generalized tank car safety design optimization model that addresses this tradeoff. The optimization model enables evaluation of each element of tank car safety design, independently and in combination with one another. We present the optimization model by identifying a set of Pareto-optimal solutions for a baseline tank car design in a bicriteria decision problem. This model provides a quantitative framework for a rational decision-making process involving tank car safety design enhancements to reduce the risk of transporting hazardous materials.

Analysis and design on airport safety information management system

Directory of Open Access Journals (Sweden)

Yan Lin

2017-01-01

Full Text Available Airport safety information management system is the foundation of implementing safety operation, risk control, safety performance monitor, and safety management decision for the airport. The paper puts forward the architecture of airport safety information management system based on B/S model, focuses on safety information processing flow, designs the functional modules and proposes the supporting conditions for system operation. The system construction is helpful to perfecting the long effect mechanism driven by safety information, continually increasing airport safety management level and control proficiency．

Multi-dimensional database design and implementation of dam safety monitoring system

Directory of Open Access Journals (Sweden)

Zhao Erfeng

2008-09-01

Full Text Available To improve the effectiveness of dam safety monitoring database systems, the development process of a multi-dimensional conceptual data model was analyzed and a logic design was achieved in multi-dimensional database mode. The optimal data model was confirmed by identifying data objects, defining relations and reviewing entities. The conversion of relations among entities to external keys and entities and physical attributes to tables and fields was interpreted completely. On this basis, a multi-dimensional database that reflects the management and analysis of a dam safety monitoring system on monitoring data information has been established, for which factual tables and dimensional tables have been designed. Finally, based on service design and user interface design, the dam safety monitoring system has been developed with Delphi as the development tool. This development project shows that the multi-dimensional database can simplify the development process and minimize hidden dangers in the database structure design. It is superior to other dam safety monitoring system development models and can provide a new research direction for system developers.

EC6 safety design improvements

Energy Technology Data Exchange (ETDEWEB)

Yu, S.; Lee, A.G.; Soulard, M. [Candu Energy Inc., Mississauga, ON (Canada)

2014-07-01

The Enhanced CANDU 6 (EC6) builds on the proven high performance design such as the Qinshan CANDU 6 reactor, and has made improvements to safety, operational performance, and has incorporated extensive operational feedback. Completion of all three phases of the pre-licensing design review by the Canadian Regulator - the Canadian Nuclear Safety Commission has provided a higher level of assurance that the EC6 reference design has taken modern regulatory requirements and expectations into account and further confirmed that there are no fundamental barriers to licensing the EC6 design in Canada. The EC6 design is based on the defence-in-depth principles in INSAG-10 and provides further safety features that address the lessons learned from Fukushima. With these safety features, the EC6 design has strengthened accident prevention as the first priority in the defence-in-depth strategy, as outlined in INSAG-10. As well, the EC6 design has incorporated further mitigation measures to provide additional protection of the public and the environment if the preventive measures fail. The EC6 design has an appropriate combination of inherent, passive safety characteristics, engineered features and administrative safety measures to effectively prevent and mitigate severe accident progressions. A strong contributor to the robustness and redundancy of CANDU design is the two-group separation philosophy. This ensures a high degree of independence between safety systems as well as physical separation and functional independence in how fundamental safety functions are provided. This paper will describe the following safety features based on the application of defence-in-depth and design approach to prevent beyond design basis events progressing to severe accidents and to mitigate the consequences if it occurs: Improved steam generator heat sink via a more reliable emergency heat removal system; Increased time before manual field actions are required via enhanced capacity of

System Design and the Safety Basis

International Nuclear Information System (INIS)

Ellingson, Darrel

2008-01-01

The objective of this paper is to present the Bechtel Jacobs Company, LLC (BJC) Lessons Learned for system design as it relates to safety basis documentation. BJC has had to reconcile incomplete or outdated system description information with current facility safety basis for a number of situations in recent months. This paper has relevance in multiple topical areas including documented safety analysis, decontamination and decommissioning (D and D), safety basis (SB) implementation, safety and design integration, potential inadequacy of the safety analysis (PISA), technical safety requirements (TSR), and unreviewed safety questions. BJC learned that nuclear safety compliance relies on adequate and well documented system design information. A number of PIS As and TSR violations occurred due to inadequate or erroneous system design information. As a corrective action, BJC assessed the occurrences caused by systems design-safety basis interface problems. Safety systems reviewed included the Molten Salt Reactor Experiment (MSRE) Fluorination System, K-1065 fire alarm system, and the K-25 Radiation Criticality Accident Alarm System. The conclusion was that an inadequate knowledge of system design could result in continuous non-compliance issues relating to nuclear safety. This was especially true with older facilities that lacked current as-built drawings coupled with the loss of 'historical knowledge' as personnel retired or moved on in their careers. Walkdown of systems and the updating of drawings are imperative for nuclear safety compliance. System design integration with safety basis has relevance in the Department of Energy (DOE) complex. This paper presents the BJC Lessons Learned in this area. It will be of benefit to DOE contractors that manage and operate an aging population of nuclear facilities

Introduction of Autonomous Vehicles: Roundabouts Design and Safety Performance Evaluation

Directory of Open Access Journals (Sweden)

Aleksandra Deluka Tibljaš

2018-04-01

Full Text Available Driving experiences provided by the introduction of new vehicle technologies are directly impacting the criteria for road network design. New criteria should be taken into consideration by designers, researchers and car owners in order to assure traffic safety in changed conditions that will appear with, for example, introduction of Autonomous Vehicles (AVs in everyday traffic. In this paper, roundabout safety level is analysed on the originally developed microsimulation model in circumstances where different numbers of AVs vehicles are mixed with Conventional Vehicles (CVs. Field data about speed and traffic volumes from existing roundabouts in Croatia were used for development of the model. The simulations done with the Surrogate Safety Assessment Model (SSAM give some relevant highlights on how the introduction of AVs could change both operational and safety parameters at roundabouts. To further explore the effects on safety of roundabouts with the introduction of different shares of AVs, hypothetical safety treatments could be tested to explore whether their effects may change, leading to the estimation of a new set of Crash Modification Factors.

Distinctive safety aspects of the CANDU-PHW reactor design

International Nuclear Information System (INIS)

Kugler, G.

1980-01-01

Two lectures are presented in this report. They were prepared in response to a request from IAEA to provide information on the 'Special characteristics of the safety analysis of heavy water reactors' to delegates from member states attending the Interregional Training Course on Safety Analysis Review, held at Karlsruhe, November 19 to December 20, 1979. The CANDU-PHW reactor is used as a model for discussion. The first lecture describes the distinctive features of the CANDU reactor and how they impact on reactor safety. In the second lecture the Canadian safety philosophy, the safety design objective, and other selected topics on reactor safety analysis are discussed. The material in this report was selected with a view to assisting those not familiar with the CANDU heavy water reactor design in evaluating the distinctive safety aspects of these reactors. (auth)

Development of design and safety analysis supporting system for casks

International Nuclear Information System (INIS)

Ohsono, Katsunari; Higashino, Akira; Endoh, Shuji

1993-01-01

Mitsubishi heavy Industries has developed a design and safety analysis supporting system 'CADDIE' (Cask Computer Aided Design, Drawing and Integrated Evaluation System), with the following objectives: (1) Enhancement of efficiency of the design and safety analysis (2) Further advancement of design quality (3) Response to the diversification of design requirements. The features of this system are as follows: (1) The analysis model data common to analyses is established, and it is prepared automatically from the model made by CAD. (2) The input data for the analysis code is available by simple operation of conversation type from the analysis model data. (3) The analysis results are drawn out in diagrams by output generator, so as to facilitate easy observation. (4) The data of material properties, fuel assembly data, etc. required for the analyses are made available as a data base. (J.P.N.)

Integrated Safety in Design

DEFF Research Database (Denmark)

Schultz, Casper Siebken; Jørgensen, Kirsten

2014-01-01

An on-going research project investigates the inclusion of health and safety considerations in the design phase as a means to achieve a higher level of health and safety in the construction industry. Moreover, the approach is coupled to the overall quality efforts. Two architectural firms and two...... consulting engineering firms are project participants. The hypothesis is that health and safety problems in execution can be prevented through better planning in the early stages of the construction processes and that accidents are prevented by providing safety. In the first stage of the research project...... a theoretical framework is developed from a combination of existing literature on health and safety and a mapping of existing practices based on interviews in all four companies. The interviews revealed that the basic knowledge on OHS among architects and engineers is limited. Also currently designers typically...

Safety design integrated in the Building Delivery System

DEFF Research Database (Denmark)

Jørgensen, Kirsten

2012-01-01

phases of the building delivery system by using the principle of the lean construction modelling. The method for the research was to go through the lean construction building delivery system step by step and create a normative description of what to do, when to do and how to do to fully integration...... of safety in each process. The group of participants who created the description had a high experience in a combination of research, safety and health in general and especial in construction and knowledge of the lean construction processes both from the clients perspective as well as from the designers...... and the consultants. The result is a concept and guideline including control schemes for how to integrate safety design in the lean construction building delivery system including what to do and when. The concept has been tested in an educational context and found useful by the designers. The practical value...

Safety culture in design. Final report

International Nuclear Information System (INIS)

Macchi, L.; Pietikaeinen, E.; Liinasuo, M.; Savioja, P.; Reiman, T.; Wahlstroem, M.; Kahlbom, U.; Rollenhagen, C.

2013-04-01

In this report we approach design from a safety culture approach As this research area is new and understudied, we take a wide scope on the issue. Different theoretical perspectives that can be taken when improving safety of the design process are considered in this report. We suggest that in the design context the concept of safety culture should be expanded from an organizational level to the level of the network of organizations involved in the design activity. The implication of approaching the design process from a safety culture perspective are discussed and the results of the empirical part of the research are presented. In the interview study in Finland and Sweden we identified challenges and opportunities in the design process from safety culture perspective. Also, a small part of the interview study concentrated on state of the art human factors engineering (HFE) practices in Finland and the results relating to that are presented. This report provide a basis for future development of systematic good design practices and for providing guidelines that can lead to safe and robust technical solutions. (Author)

Safety culture in design. Final report

Energy Technology Data Exchange (ETDEWEB)

Macchi, L.; Pietikaeinen, E.; Liinasuo, M.; Savioja, P.; Reiman, T.; Wahlstroem, M. [VTT Technical Research Centre of Finland, Espoo (Finland); Kahlbom, U. [Risk Pilot AB, Stockholm (Sweden); Rollenhagen, C. [Vattenfall, Stockholm, (Sweden)

2013-04-15

In this report we approach design from a safety culture approach As this research area is new and understudied, we take a wide scope on the issue. Different theoretical perspectives that can be taken when improving safety of the design process are considered in this report. We suggest that in the design context the concept of safety culture should be expanded from an organizational level to the level of the network of organizations involved in the design activity. The implication of approaching the design process from a safety culture perspective are discussed and the results of the empirical part of the research are presented. In the interview study in Finland and Sweden we identified challenges and opportunities in the design process from safety culture perspective. Also, a small part of the interview study concentrated on state of the art human factors engineering (HFE) practices in Finland and the results relating to that are presented. This report provide a basis for future development of systematic good design practices and for providing guidelines that can lead to safe and robust technical solutions. (Author)

Safety design of Qinshan Nuclear Power Plant

International Nuclear Information System (INIS)

Ouyang Yu; Zhang Lian; Du Shenghua; Zhao Jiayu

1984-01-01

Safety issues have been greatly emphasized through the design of the Qinshan Nuclear Power Plant. Reasonable safety margine has been taken into account in the plant design parameters, the design incorporated various safeguard systems, such as engineering safety feature systems, safety protection systems and the features to resist natural catastrophes, e. g. earthquake, hurricanes, tide and so on. Preliminary safety analysis and environmental effect assessment have been done and anti-accident provisions and emergency policy were carefully considered. Qinshan Nuclear Power Plant safety related systems are designed in accordance with the common international standards established in the late 70's, as well as the existing engineering standard of China

Safety assessment in plant layout design using indexing approach: Implementing inherent safety perspective

International Nuclear Information System (INIS)

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-01-01

Layout planning plays a key role in the inherent safety performance of process plants since this design feature controls the possibility of accidental chain-events and the magnitude of possible consequences. A lack of suitable methods to promote the effective implementation of inherent safety in layout design calls for the development of new techniques and methods. In the present paper, a safety assessment approach suitable for layout design in the critical early phase is proposed. The concept of inherent safety is implemented within this safety assessment; the approach is based on an integrated assessment of inherent safety guideword applicability within the constraints typically present in layout design. Application of these guidewords is evaluated along with unit hazards and control devices to quantitatively map the safety performance of different layout options. Moreover, the economic aspects related to safety and inherent safety are evaluated by the method. Specific sub-indices are developed within the integrated safety assessment system to analyze and quantify the hazard related to domino effects. The proposed approach is quick in application, auditable and shares a common framework applicable in other phases of the design lifecycle (e.g. process design). The present work is divided in two parts: Part 1 (current paper) presents the application of inherent safety guidelines in layout design and the index method for safety assessment; Part 2 (accompanying paper) describes the domino hazard sub-index and demonstrates the proposed approach with a case study, thus evidencing the introduction of inherent safety features in layout design

Nuclear reaction models - source term estimation for safety design in accelerators

International Nuclear Information System (INIS)

Nandy, Maitreyee

2013-01-01

Accelerator driven subcritical system (ADSS) employs proton induced spallation reaction at a few GeV. Safety design of these systems involves source term estimation in two steps - multiple fragmentation of the target and n+γ emission through a fast process followed by statistical decay of the primary fragments. The prompt radiation field is estimated in the framework of quantum molecular dynamics (QMD) theory, intra-nuclear cascade or Monte Carlo calculations. A few nuclear reaction model codes used for this purpose are QMD, JQMD, Bertini, INCL4, PHITS, followed by statistical decay codes like ABLA, GEM, GEMINI, etc. In the case of electron accelerators photons and photoneutrons dominate the prompt radiation field. High energy photon yield through Bremsstrahlung is estimated in the framework of Born approximation while photoneutron production is calculated using giant dipole resonance and quasi-deuteron formation cross section. In this talk hybrid and exciton PEQ models and QMD formalism will be discussed briefly

Cost vs. safety: A novel design for t

Directory of Open Access Journals (Sweden)

Komali Kantamaneni

2017-08-01

Full Text Available Tornadoes are dangerous and destructive weather phenomena. The strongest category of tornadoes on the enhanced Fujita and TORRO scales is responsible for 75% of property destruction and deaths across the globe. These issues highlight the need for new design practices aimed at producing tornado proof homes in particular 3D CAD models in tornado prone zones at current climatic scenarios. Previous studies were entirely based on traditional slants and failed to offer a reliable tornado proof home, other than small rooms and trailers, while, none of the literature concentrated on multiple factors (cost, safety and high-wind proof. Therefore, a knowledge gap exists. In order to address the current research gap, this study attempts to develop an innovative 3D CAD model for tornado resistant homes by incorporating 2 PA (Two Path Analysis. Consequently, this study provides a new design using a 3D-CAD model for a tornado resistant home as in Path One and cost and safety scenarios in Path Two. However, this new design utilizes missile steel and shield technology. Preliminary results showed that, while this new design is safer and more technically sophisticated, it involves an increase of 25–30% in construction costs. However, this increased expense is low in comparison with rebuilding costs.

PHWR safety: design, siting and construction

International Nuclear Information System (INIS)

Sharma, V.K.

2002-01-01

In all activities associated with NPPs viz. siting, design, construction, commissioning and operation, safety is given overriding importance. The safety design principles of PHWRs are based on defence-in-depth approach, physical and functional separation between process and safety systems and also among various safety systems, redundancy to meet single failure criteria and postulation of a number of design basis events for which the plant must be designed. Apart from engineered safety systems, PHWRs have inherent characteristics which contribute to safety. In siting of a NPP, it is required to ensure that the given site does not pose undue radiological hazard to public and the environment both during normal operation as well as during and following an accident condition. For this purpose, all site related external events, both natural and man induced, are assessed for their effect on the plant and are considered as part of the design basis. Possible radiological impact of the NPP on environment and surrounding population is assessed and ensured to be within acceptable limits. During construction phase, it is essential that the NPP be built in accordance with design intent and with required quality of workmanship to ensure that the NPP will remain safe during all states of operation. This is achieved through careful execution and QA activities encompassing all aspects of component fabrication at manufacturer works, civil construction, site erection, assembly, and commissioning. Future trends in nuclear safety will continue to be based on existing principles which have proved to be sound. These will be further strengthened by features such as increasing use of passive means of performing safety functions and a more explicit treatment of severe accidents. (author)

SAFETY BASIS DESIGN DEVELOPMENT CHALLENGES IMECE2007-42747

Energy Technology Data Exchange (ETDEWEB)

RYAN GW

2007-09-24

'Designing in Safety' is a desired part of the development of any new potentially hazardous system, process, or facility. It is a required part of nuclear safety activities as specified in the U.S. Department of Energy (DOE) Order 420.B, Facility Safety. This order addresses the design of nuclear related facilities developed under federal regulation IOCFR830, Nuclear Safety Management. IOCFR830 requires that safety basis documentation be provided to identify how nuclear safety is being adequately addressed as a condition for system operation (e.g., the safety basis). To support the development of the safety basis, a safety analysis is performed. Although the concept of developing a design that addresses 'Safety is simple, the execution can be complex and challenging. This paper addresses those complexities and challenges for the design activity of a system to treat sludge, a corrosion product of spent nuclear fuel, at DOE's Hanford Site in Washington State. The system being developed is referred to as the Sludge Treatment Project (STP). This paper describes the portion of the safety analysis that addresses the selection of design basis events using the experience gained from the STP and the development of design requirements for safety features associated with those events. Specifically, the paper describes the safety design process and the application of the process for two types of potential design basis accidents associated with the operation of the system, (1) flashing spray leaks and (2) splash and splatter leaks. Also presented are the technical challenges that are being addressed to develop effective safety features to deal with these design basis accidents.

SAFETY BASIS DESIGN DEVELOPMENT CHALLENGES IMECE2007-42747

International Nuclear Information System (INIS)

RYAN GW

2007-01-01

'Designing in Safety' is a desired part of the development of any new potentially hazardous system, process, or facility. It is a required part of nuclear safety activities as specified in the U.S. Department of Energy (DOE) Order 420.B, Facility Safety. This order addresses the design of nuclear related facilities developed under federal regulation IOCFR830, Nuclear Safety Management. IOCFR830 requires that safety basis documentation be provided to identify how nuclear safety is being adequately addressed as a condition for system operation (e.g., the safety basis). To support the development of the safety basis, a safety analysis is performed. Although the concept of developing a design that addresses 'Safety is simple, the execution can be complex and challenging. This paper addresses those complexities and challenges for the design activity of a system to treat sludge, a corrosion product of spent nuclear fuel, at DOE's Hanford Site in Washington State. The system being developed is referred to as the Sludge Treatment Project (STP). This paper describes the portion of the safety analysis that addresses the selection of design basis events using the experience gained from the STP and the development of design requirements for safety features associated with those events. Specifically, the paper describes the safety design process and the application of the process for two types of potential design basis accidents associated with the operation of the system, (1) flashing spray leaks and (2) splash and splatter leaks. Also presented are the technical challenges that are being addressed to develop effective safety features to deal with these design basis accidents

Mitigating construction safety risks using prevention through design.

Science.gov (United States)

Gangolells, Marta; Casals, Miquel; Forcada, Núria; Roca, Xavier; Fuertes, Alba

2010-04-01

Research and practice have demonstrated that decisions made prior to work at construction sites can influence construction worker safety. However, it has also been argued that most architects and design engineers possess neither the knowledge of construction safety nor the knowledge of construction processes necessary to effectively perform Construction Hazards Prevention through Design (CHPtD). This paper introduces a quantitative methodology that supports designers by providing a way to evaluate the safety-related performance of residential construction designs using a risk analysis-based approach. The methodology compares the overall safety risk level of various construction designs and ranks the significance of the various safety risks of each of these designs. The methodology also compares the absolute importance of a particular safety risk in various construction designs. Because the methodology identifies the relevance of each safety risk at a particular site prior to the construction stage, significant risks are highlighted in advance. Thus, a range of measures for mitigating safety risks can then be implemented during on-site construction. The methodology is specially worthwhile for designers, who can compare construction techniques and systems during the design phase and determine the corresponding level of safety risk without their creative talents being restricted. By using this methodology, construction companies can improve their on-site safety performance. Copyright 2010 Elsevier Ltd. All rights reserved.

Safety design philosophy of Mitsubishi PWRs

International Nuclear Information System (INIS)

Hakata, T.; Kitamura, T.

1993-01-01

The basic safety design philosophy of Mitsubishi pressurized water reactors (PWRs) is discussed and compared with the British PWR. PWR plants are designed in accordance with the Japanese regulatory guidelines which are similar to American and International Atomic Energy Agency (IAEA) safety criteria and are based on defence-in-depth principles. The high reliability of nuclear power plants is especially emphasized in Mitsubishi PWRs, and this has been demonstrated by the good operating experience of PWR plants in Japan. The safety system designs of six key items, which were discussed in the recent review of overseas designs by British utilities, are addressed to show the difference in the design philosophy between the United Kingdom and Japan. (Author)

Appendix C: safety design rationale

International Nuclear Information System (INIS)

Ghose, S.

1985-01-01

A brief discussion of the rationale for safety design of fusion plants is presented in the main text. Further detail safety considerations are presented in this appendix in the form of charts and tables. The author present some of the major safety criteria and other criteria used in blanket selection here

A fuzzy-logic-based approach to qualitative safety modelling for marine systems

International Nuclear Information System (INIS)

Sii, H.S.; Ruxton, Tom; Wang Jin

2001-01-01

Safety assessment based on conventional tools (e.g. probability risk assessment (PRA)) may not be well suited for dealing with systems having a high level of uncertainty, particularly in the feasibility and concept design stages of a maritime or offshore system. By contrast, a safety model using fuzzy logic approach employing fuzzy IF-THEN rules can model the qualitative aspects of human knowledge and reasoning processes without employing precise quantitative analyses. A fuzzy-logic-based approach may be more appropriately used to carry out risk analysis in the initial design stages. This provides a tool for working directly with the linguistic terms commonly used in carrying out safety assessment. This research focuses on the development and representation of linguistic variables to model risk levels subjectively. These variables are then quantified using fuzzy sets. In this paper, the development of a safety model using fuzzy logic approach for modelling various design variables for maritime and offshore safety based decision making in the concept design stage is presented. An example is used to illustrate the proposed approach

Design provisions for safety

International Nuclear Information System (INIS)

Birkhofer, A.

1983-01-01

Design provisions for safety of nuclear power plants are based on a well balanced concept: the public is protected against a release of radioactive material by multiple barriers. These barriers are protected according to a 'defence-in-depth' principle. The reactor safety concept is primarily aimed at the prevention of accidents, especially fuel damage. Additionally, measures for consequence limitation are provided in order to prevent a severe release of radioactivity to the environment. However, it is difficult to judge the overall effectiveness of such devices. In a comprehensive safety analysis it has to be shown that the protection systems and safeguards work with sufficient reliability in the event of an accident. For the reliability assessment deterministic criteria (single failure, redundancy, fail-safe, demand for diversity) play an important role. Increasing efforts have been made to assess reliability quantitatively by means of probabilistic methods. It is now usual to perform reliability analyses of essential systems of nuclear power plants in the course of licensing procedures. As an additional level of emergency measures for a further reduction of hazards a reasonable amount of accident information has to be transferred. Operational experience may be considered as an important feedback to the design of plant safety features. Operator training has to include, besides skill in performing of operating procedures, the training of a flexible response to different accident situations. Experience has shown that the design provisions for safety could prevent dangerous release of the radioactive material to the environment after an accident has occurred. For future developments of reactor safety, extensive analyses of operating experience are of great importance. The main goal should be to enhance the reliability of measures for accident prevention, which prevent the core from meltdown or other damages

Safety Analysis for Key Design Features of KALIMER-600 Design Concept

Energy Technology Data Exchange (ETDEWEB)

Lee, Yong Bum; Kwon, Y. M.; Kim, E. K.; Suk, S. D.; Chang, W. P.; Jeong, H. Y.; Ha, K. S

2007-02-15

This report contains the safety analyses of the KALIMER-600 conceptual design which KAERI has been developing under the Long-term Nuclear R and D Program. The analyses have been performed reflecting the design developments during the second year of the 4th design phase in the program. The specific presentations are the key design features with the safety principles for achieving the safety objectives, the event categorization and safety criteria, and results on the safety analyses for the DBAs and ATWS events, the containment performance, and the channel blockages. The safety analyses for both the DBAs and ATWS events have been performed using SSC-K version 1.3., and the results have shown the fulfillment of the safety criteria for DBAs with conservative assumptions. The safety margins as well as the inherent safety also have been confirmed for the ATWS events. For the containment performance analysis, ORIGEN-2.1 and CONTAIN-LMR have been used. In results, the structural integrity has been acceptable and the evaluated exposure dose rate has been complied with 10 CFR 100 and PAG limits. The analysis results for flow blockages of 6-subchannels, 24-subchannels, and 54- subchannels with the MATRA-LMR-FB code, have assured the integrity of subassemblies.

Design safety improvements of Kozloduy NPP

International Nuclear Information System (INIS)

Hinovski, I.

1999-01-01

Design safety improvements of Kozloduy NPP, discussed in detail, are concerned with: primary circuit integrity; reactor pressure vessel integrity; primary coolant piping integrity; primary coolant overpressure protection; leak before break status; design basis accidents and transients; severe accident analysis; improvements of safety and support systems; containment/confinement leak tightness and strength; seismic safety improvements; WWER-1000 control rod insertion; upgrading and modernization of Units 5 and 6; Year 2000 problem

Safety in the ARIES Tokamak Design Study

International Nuclear Information System (INIS)

Herring, J.S.; Wong, C.P.-C.; Cheng, E.T.; Grotz, S.

1989-01-01

Safety is one of the primary goals of the ARIES Tokamak Design Study. Public safety goals are the achievement passive safety which is demonstrable in tests that could precede operation and the assurance that releases from accidents be passively limited such that no evacuation plan in necessary. Strategies for safety of the plant investment are factory fabrication, short construction times and a design such that no off-normal operational transient results in damage which could not be repaired in routine maintenance. ARIES-I, the first of three 'visions' of potential tokamak reactors, will use He at 5 MPa as a blanket coolant and SiC/composite ceramic for the first wall and blanket materials. Both the coolant and the structural material were chosen for their low activation, both in the short term after accidents and for long term waste management. The breeder, Li 4 SiO 4 , was also chosen for low activation. Contemporary plasma physics and aggressive technology are used in ARIES-I, which results in very high toroidal fields (24 T maximum at the coil). The stored TF energy will be about 130 GJ. A central concern is the safe discharge of this stored energy under electrical fault conditions and prevention of a failure in the magnet set from propagating into systems containing radioactive inventories. The TF coil system consists of 16 coils, each containing two separate windings powered by two independent power supplies. Arcs and shorts between the two power supply systems and across individual windings have been modeled. In addition, delay or failure in circuit breaker opening has been modeled. The safety impacts of LOCA, LOFA and disruptive events have also been evaluated. 8 refs., 4 figs., 7 tabs

Safety in the design of production lines

DEFF Research Database (Denmark)

Dyhrberg, Mette Bang; Broberg, Ole; Jacobsen, Peter

2006-01-01

This paper is a case study report on how safety considerations were handled in the process of redesigning a production line. The design process was characterized as a specification and negotiation process between engineers from the company and the supplier organization. The new production line...... in the specification material nor in their face-to-face meetings with the supplier. Safety aspects were not part of their work practice. On this basis, it was suggested that formal guidelines or procedures for integrating safety in the design of production lines would have no effect. Instead, the researchers set up...... became safer, but not as a result of any intentional plan to integrate safety aspects into the design process. Instead, the supplier’s design of a new piece of equipment had a higher built-in safety level. The engineering team in the company was aware of the importance of safety aspects neither...

Preliminary safety design analysis of KALIMER

Energy Technology Data Exchange (ETDEWEB)

Suk, Soo Dong; Kwon, Y. M.; Kim, K. D. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-03-01

The national long-term R and D program updated in 1997 requires Korea Atomic Energy Research Institute(KAERI) to complete by the year 2006 the basic design of Korea Advanced Liquid Metal Reactor (KALIMER), along with supporting R and D work, with the capability of resolving the issue of spent fuel storage as well as with significantly enhanced safety. KALIMER is a 150 MWe pool-type sodium cooled prototype reactor that uses metallic fuel. The conceptual design is currently under way to establish a self consistent design meeting a set of the major safety design requirements for accident prevention. Some of current emphasis include those for inherent and passive means of negative reactivity insertion and decay heat removal, high shutdown reliability, prevention of and protection from sodium chemical reaction, and high seismic margin, among others. All of these requirements affect the reactor design significantly and involve supporting R and D programs of substance. This document first introduces a set of safety design requirements and accident evaluation criteria established for the conceptual design of KALIMER and then summarizes some of the preliminary results of engineering and design analyses performed for the safety of KALIMER. 19 refs., 19 figs., 6 tabs. (Author)

Multi-person and multi-attribute design evaluations using evidential reasoning based on subjective safety and cost analyses

International Nuclear Information System (INIS)

Wang, J.; Yang, J.B.; Sen, P.

1996-01-01

This paper presents an approach for ranking proposed design options based on subjective safety and cost analyses. Hierarchical system safety analysis is carried out using fuzzy sets and evidential reasoning. This involves safety modelling by fuzzy sets at the bottom level of a hierarchy and safety synthesis by evidential reasoning at higher levels. Fuzzy sets are also used to model the cost incurred for each design option. An evidential reasoning approach is then employed to synthesise the estimates of safety and cost, which are made by multiple designers. The developed approach is capable of dealing with problems of multiple designers, multiple attributes and multiple design options to select the best design. Finally, a practical engineering example is presented to demonstrate the proposed multi-person and multi-attribute design selection approach

Fire Safety Design of Wood Structures

DEFF Research Database (Denmark)

Hertz, Kristian Dahl

2006-01-01

Lecture Notes on Fire Safety Design of Wood Structures including charring of wood and load bearing capacity of beams, columns, and connections.......Lecture Notes on Fire Safety Design of Wood Structures including charring of wood and load bearing capacity of beams, columns, and connections....

General design safety principles for nuclear power plants

International Nuclear Information System (INIS)

1986-01-01

This Safety Guide provides the safety principles and the approach that have been used to implement the Code in the Safety Guides. These safety principles and the approach are tied closely to the safety analyses needed to assist the design process, and are used to verify the adequacy of nuclear power plant designs. This Guide also provides a framework for the use of other design Safety Guides. However, although it explains the principles on which the other Safety Guides are based, the requirements for specific applications of these principles are mostly found in the other Guides

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (French Edition)

International Nuclear Information System (INIS)

2017-01-01

This publication establishes requirements applicable to the design of nuclear power plants and elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. It will be useful for organizations involved in design, manufacture, construction, modification, maintenance, operation and decommissioning of nuclear power plants, as well as for regulatory bodies. A review of Safety Requirements publications was commenced in 2011 following the accident in the Fukushima Daiichi nuclear power plant in Japan. The review revealed no significant areas of weakness and resulted in just a small set of amendments to strengthen the requirements and facilitate their implementation, which are contained in the present publication.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Russian Edition)

International Nuclear Information System (INIS)

2016-01-01

This publication establishes requirements applicable to the design of nuclear power plants and elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. It will be useful for organizations involved in design, manufacture, construction, modification, maintenance, operation and decommissioning of nuclear power plants, as well as for regulatory bodies. A review of Safety Requirements publications was commenced in 2011 following the accident in the Fukushima Daiichi nuclear power plant in Japan. The review revealed no significant areas of weakness and resulted in just a small set of amendments to strengthen the requirements and facilitate their implementation, which are contained in the present publication.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Arabic Edition)

International Nuclear Information System (INIS)

2017-01-01

This publication establishes requirements applicable to the design of nuclear power plants and elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. It will be useful for organizations involved in design, manufacture, construction, modification, maintenance, operation and decommissioning of nuclear power plants, as well as for regulatory bodies. A review of Safety Requirements publications was commenced in 2011 following the accident in the Fukushima Daiichi nuclear power plant in Japan. The review revealed no significant areas of weakness and resulted in just a small set of amendments to strengthen the requirements and facilitate their implementation, which are contained in the present publication.

Safety analysis for key design features of KALIMER-600 design concept

International Nuclear Information System (INIS)

Lee, Yong-Bum; Kwon, Y. M.; Kim, E. K.; Suk, S. D.; Chang, W. P.; Joeng, H. Y.; Ha, K. S.; Heo, S.

2005-03-01

KAERI is developing the conceptual design of a Liquid Metal Reactor, KALIMER-600 (Korea Advanced LIquid MEtal Reactor) under the Long-term Nuclear R and D Program. KALIMER-600 addresses key issues regarding future nuclear power plants such as plant safety, economics, proliferation, and waste. In this report, key safety design features are described and safety analyses results for typical ATWS accidents, containment design basis accidents, and flow blockages in the KALIMER design are presented. First, the basic approach to achieve the safety goal and main design features of KALIMER-600 are introduced in Chapter 1, and the event categorization and acceptance criteria for the KALIMER-600 safety analysis are described in Chapter 2, In Chapter 3, results of inherent safety evaluations for the KALIMER-600 conceptual design are presented. The KALIMER-600 core and plant system are designed to assure benign performance during a selected set of events without either reactor control or protection system intervention. Safety analyses for the postulated anticipated transient without scram (ATWS) have been performed using the SSC-K code to investigate the KALIMER-600 system response to the events. The objectives of Chapter 4, are to assess the response of KALIMER-600 containment to the design basis accidents and to evaluate whether the consequences are acceptable or not in the aspect of structural integrity and the exposure dose rate. In Chapter 5, the analysis of flow blockage for KALIMER-600 with the MATRA-LMR-FB code, which has been developed for the internal flow blockage in a LMR subassembly, are described. The cases with a blockage of 6-subchannel, 24-subchannel, and 54-subchannel are analyzed

ELFR: The European Lead Fast Reactor. Design, Safety Approach and Safety Characteristics

International Nuclear Information System (INIS)

Alemberti, Alessandro

2012-01-01

• In the framework of the LEADER project, the safety approach for a Lead cooled fast reactor has been defined and, in particular, all the possible challenges to the main safety functions and their mechanisms have been specified, in order to better define the needed provisions. • On the basis of the above and taking into account the results of the safety analyses performed during previous project (ELSY), a reference configuration of the ELFR plant has been consolidated, by improving and updating the plant design features. In particular, the emerged safety concerns have been analyzed in the LEADER project and a new set of design options and safety provisions have been proposed. • The combination of favourable Lead coolant inherent characteristics and plant design features, specifically developed to face identified challenges, resulted in a very robust and forgiving design, even in very extreme conditions, as a Fukushima-like scenario

Development of ABWR-2 and its safety design

International Nuclear Information System (INIS)

Takafumi, Anegawa; Kenji, Tateiwa

2002-01-01

This paper reports the current status of development project on ABWR-II, a next generation reactor design based on ABWR, and its safety design. This project was initiated over a decade ago and has completed three phases to date. In Phase I (1991-92), basic design requirements were discussed and several plant concepts were studied. In Phase II (1993-95), key design features were selected in order to establish a reference reactor concept. In Phase III (1996-2000), based on the reference reactor concept, modifications and improvements were made to fulfill the design requirements. By adopting large electric output (1 700 MW), large fuel bundle, modified ECCS, and passive heat removal systems, among other design features, we achieved a design concept capable of increasing both economic competitiveness and safety performance. Main focus of this paper will be on the safety design, safety performance, and further research needs related to safety. (authors)

Nuclear safety cooperation for Soviet designed reactors

International Nuclear Information System (INIS)

Reisman, A.W.; Horak, W.C.

1995-01-01

The nuclear accident at the Chernobyl nuclear power plant in 1986 first alerted the West to the significant safety risks of Soviet designed reactors. Five years later, this concern was reaffirmed when the IAEA, as a result of a review by an international team of nuclear safety experts, announced that it did not believe the Kozloduy nuclear power plants in Bulgaria could be operated safely. To address these safety concerns, the G-7 summit in Munich in July 1992 outlined a five point program to address the safety problems of Soviet Designed Reactors: operational safety improvement; near-term technical improvements to plants based on safety assessment; enhancing regulatory regimes; examination of the scope for replacing less safe plants by the development of alternative energy sources and the more efficient use of energy; and upgrading of the plants of more recent design. As of early 1994, over 20 countries and international organizations have pledged hundreds of millions of dollars in financial assistance to improve safety. This paper summarizes these assistance efforts for Soviet designed reactors, draws lessons learned from these activities, and offers some options for better addressing these concerns

Small Column Ion Exchange Design and Safety Strategy

International Nuclear Information System (INIS)

Huff, T.; Rios-Armstrong, M.; Edwards, R.; Herman, D.

2011-01-01

Small Column Ion Exchange (SCIX) is a transformational technology originally developed by the Department of Energy (DOE) Environmental Management (EM-30) office and is now being deployed at the Savannah River Site (SRS) to significantly increase overall salt processing capacity and accelerate the Liquid Waste System life-cycle. The process combines strontium and actinide removal using Monosodium Titanate (MST), Rotary Microfiltration, and cesium removal using Crystalline Silicotitanate (CST, specifically UOP IONSIV(reg s ign)IE-911 ion exchanger) to create a low level waste stream to be disposed in grout and a high level waste stream to be vitrified. The process also includes preparation of the streams for disposal, e.g., grinding of the loaded CST material. These waste processing components are technically mature and flowsheet integration studies are being performed including glass formulations studies, application specific thermal modeling, and mixing studies. The deployment program includes design and fabrication of the Rotary Microfilter (RMF) assembly, ion-exchange columns (IXCs), and grinder module, utilizing an integrated system safety design approach. The design concept is to install the process inside an existing waste tank, Tank 41H. The process consists of a feed pump with a set of four RMFs, two IXCs, a media grinder, three Submersible Mixer Pumps (SMPs), and all supporting infrastructure including media receipt and preparation facilities. The design addresses MST mixing to achieve the required strontium and actinide removal and to prevent future retrieval problems. CST achieves very high cesium loadings (up to 1,100 curies per gallon (Ci/gal) bed volume). The design addresses the hazards associated with this material including heat management (in column and in-tank), as detailed in the thermal modeling. The CST must be size reduced for compatibility with downstream processes. The design addresses material transport into and out of the grinder and

The role of probabilistic safety assessment in the design

International Nuclear Information System (INIS)

Green, A.; Ingham, E.L.

1989-01-01

The use of probabilistic safety assessment (PSA) for Heysham 2 and Torness marked a major change in the design approach to nuclear safety within the U.K. Design Safety Guidelines incorporating probabilistic safety targets required that design justification would necessitate explicit consideration of the consequence of accidents in relation to their frequency. The paper discusses these safety targets and their implications, the integration of PSA into the design process and an outline of the methodology. The influence of PSA on the design is discussed together with its role in the overall demonstration of reactor safety. (author)

Review on JMTR safety design for LEU core conversion

International Nuclear Information System (INIS)

Komori, Yoshihiro; Yokokawa, Makoto; Saruta, Toru; Inada, Seiji; Sakurai, Fumio; Yamamoto, Katsumune; Oyamada, Rokuro; Saito, Minoru

1993-12-01

Safety of the JMTR was fully reviewed for the core conversion to low enriched uranium fuel. Fundamental policies for the JMTR safety design were reconsidered based on the examination guide for safety design of test and research reactors, and safety of the JMTR was confirmed. This report describes the safety design of the JMTR from the viewpoint of major functions for reactor safety. (author)

Safety requirements applicable to the SMART design

International Nuclear Information System (INIS)

Seul, Kwang Won; Kim, Wee Kyong; Kim, Hho Jung

1999-01-01

The 330 MW thermal power of integral reactor, named SMART (System integrated Modular Advanced ReacTor), is under development at KAERI for seawater desalination application and electricity generation. The final product of nuclear desalination plant (NDP) is electricity and fresh water. Thus, in addition to the protection of the public around the plant facility from the possible release of radioactive materials, the fresh water should be prevented from radioactivity contamination. In this study, to ensure the safety of SMART reactor in the early stage of design development, the safety requirements applicable to the SMART design were investigated, based on the current regulatory requirements for the existing NPPs and the advanced light water reactor (LWR) designs. The interface requirements related to the desalination facility were also investigated, based on the recent IAEA research activities pertaining to the NDP. As a result, it was found that the current regulatory requirements and guidance for the existing NPPs and advanced LWR designs are applicable to the SMART design and its safety evaluation. However, the safety requirements related to the SMART-specific design and the desalination plant are needed to develop in the future to assure the safety of the SMART reactor

ITER plasma safety interface models and assessments

International Nuclear Information System (INIS)

Uckan, N.A.; Bartels, H-W.; Honda, T.; Amano, T.; Boucher, D.; Post, D.; Wesley, J.

1996-01-01

Physics models and requirements to be used as a basis for safety analysis studies are developed and physics results motivated by safety considerations are presented for the ITER design. Physics specifications are provided for enveloping plasma dynamic events for Category I (operational event), Category II (likely event), and Category III (unlikely event). A safety analysis code SAFALY has been developed to investigate plasma anomaly events. The plasma response to ex-vessel component failure and machine response to plasma transients are considered

Safety design guides for fire protection for CANDU 9

International Nuclear Information System (INIS)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young; A. C. D. Wright

1996-03-01

This safety design guide establishes design requirements to ensure the radiological risk to the public due to fire is acceptable and operating personnel are adequately protected from the hazards of fires. This safety design guide also specifies the safety criteria for fire protection to be applied to mitigate fires and recommends the fire protection program to be established to initiate, coordinate and document the design activities associated with fire protection. The requirements for fire protection outlined in this safety design guide shall be satisfied in the design stage and the change status of the regulatory requirements, code and standards should be traced and incorporated into this safety design guide accordingly. 1 fig., (Author) .new

Study and design of safety assessment model based on H12 reference case using GoldSim

International Nuclear Information System (INIS)

Nakajima, Kunihiko; Koo, Shigeru; Ebina, Takanori; Ebashi, Takeshi; Inagaki, Manabu

2009-07-01

Reference case of safety assessment analysis at the H12 report was calculated using the numerical code MESHNOTE and MATRICS mainly. On the other hand, recently general simulation software witch has a character of object-oriented is globally used and the numerical code GoldSim is typical software. After the H12 report, probability theory analysis and sensitivity analysis using GoldSim have carried out by statistical method for the purpose of following up safety assessment analysis at the H12 report. On this report, details of the method for the model design using GoldSim are summarized, and to confirm calculation reproducibility, verification between the H12 report and GoldSim results were carried out. And the guide book of calculation method using GoldSim is maintained for other investigators at JAEA who want to calculate reference case on the H12 report. In the future, application resources on this report will be able to upgrade probability theory analysis and other conceptual models. (author)

Predicting the effectiveness of road safety campaigns through alternative research designs.

Science.gov (United States)

Adamos, Giannis; Nathanail, Eftihia

2016-12-01

A large number of road safety communication campaigns have been designed and implemented in the recent years; however their explicit impact on driving behavior and road accident rates has been estimated in a rather low proportion. Based on the findings of the evaluation of three road safety communication campaigns addressing the issues of drinking and driving, seat belt usage, and driving fatigue, this paper applies different types of research designs (i.e., experimental, quasi-experimental, and non-experimental designs), when estimating the effectiveness of road safety campaigns, implements a cross-design assessment, and conducts a cross-campaign evaluation. An integrated evaluation plan was developed, taking into account the structure of evaluation questions, the definition of measurable variables, the separation of the target audience into intervention (exposed to the campaign) and control (not exposed to the campaign) groups, the selection of alternative research designs, and the appropriate data collection methods and techniques. Evaluating the implementation of different research designs in estimating the effectiveness of road safety campaigns, results showed that the separate pre-post samples design demonstrated better predictability than other designs, especially in data obtained from the intervention group after the realization of the campaign. The more constructs that were added to the independent variables, the higher the values of the predictability were. The construct that most affects behavior is intention, whereas the rest of the constructs have a lower impact on behavior. This is particularly significant in the Health Belief Model (HBM). On the other hand, behavioral beliefs, normative beliefs, and descriptive norms, are significant parameters for predicting intention according to the Theory of Planned Behavior (TPB). The theoretical and applied implications of alternative research designs and their applicability in the evaluation of road safety

Modeling Transients and Designing a Passive Safety System for a Nuclear Thermal Rocket Using Relap5

Science.gov (United States)

Khatry, Jivan

Long-term high payload missions necessitate the need for nuclear space propulsion. Several nuclear reactor types were investigated by the Nuclear Engine for Rocket Vehicle Application (NERVA) program of National Aeronautics and Space Administration (NASA). Study of planned/unplanned transients on nuclear thermal rockets is important due to the need for long-term missions. A NERVA design known as the Pewee I was selected for this purpose. The following transients were run: (i) modeling of corrosion-induced blockages on the peripheral fuel element coolant channels and their impact on radiation heat transfer in the core, and (ii) modeling of loss-of-flow-accidents (LOFAs) and their impact on radiation heat transfer in the core. For part (i), the radiation heat transfer rate of blocked channels increases while their neighbors' decreases. For part (ii), the core radiation heat transfer rate increases while the flow rate through the rocket system is decreased. However, the radiation heat transfer decreased while there was a complete LOFA. In this situation, the peripheral fuel element coolant channels handle the majority of the radiation heat transfer. Recognizing the LOFA as the most severe design basis accident, a passive safety system was designed in order to respond to such a transient. This design utilizes the already existing tie rod tubes and connects them to a radiator in a closed loop. Hence, this is basically a secondary loop. The size of the core is unchanged. During normal steady-state operation, this secondary loop keeps the moderator cool. Results show that the safety system is able to remove the decay heat and prevent the fuel elements from melting, in response to a LOFA and subsequent SCRAM.

Safety design guide for safety related systems for CANDU 9

International Nuclear Information System (INIS)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young; A. C. D. Wright

1996-03-01

In general, two types of safety related systems and structures exist in the nuclear plant; The one is a systems and structures which perform safety functions during the normal operation of the plant, and the other is a systems and structures which perform safety functions to mitigate events caused by failure of the normally operating systems or by naturally occurring phenomena. In this safety design guide, these systems are identified in detail, and the major events for which the safety functions are required and the major safety requirements are identified in the list. As the probabilistic safety assessments are completed during the course of the project, additions or deletions to the list may be justified. 3 tabs. (Author) .new

Safety design guide for safety related systems for CANDU 9

Energy Technology Data Exchange (ETDEWEB)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young [Korea Atomic Energy Research Institute, Daeduk (Korea, Republic of); Wright, A.C.D. [Atomic Energy of Canada Ltd., Toronto (Canada)

1996-03-01

In general, two types of safety related systems and structures exist in the nuclear plant; The one is a systems and structures which perform safety functions during the normal operation of the plant, and the other is a systems and structures which perform safety functions to mitigate events caused by failure of the normally operating systems or by naturally occurring phenomena. In this safety design guide, these systems are identified in detail, and the major events for which the safety functions are required and the major safety requirements are identified in the list. As the probabilistic safety assessments are completed during the course of the project, additions or deletions to the list may be justified. 3 tabs. (Author) .new.

Impact of Passive Safety on FHR Instrumentation Systems Design and Classification

International Nuclear Information System (INIS)

Holcomb, David Eugene

2015-01-01

Fluoride salt-cooled high-temperature reactors (FHRs) will rely more extensively on passive safety than earlier reactor classes. 10CFR50 Appendix A, General Design Criteria for Nuclear Power Plants, establishes minimum design requirements to provide reasonable assurance of adequate safety. 10CFR50.69, Risk-Informed Categorization and Treatment of Structures, Systems and Components for Nuclear Power Reactors, provides guidance on how the safety significance of systems, structures, and components (SSCs) should be reflected in their regulatory treatment. The Nuclear Energy Institute (NEI) has provided 10 CFR 50.69 SSC Categorization Guideline (NEI-00-04) that factors in probabilistic risk assessment (PRA) model insights, as well as deterministic insights, through an integrated decision-making panel. Employing the PRA to inform deterministic requirements enables an appropriately balanced, technically sound categorization to be established. No FHR currently has an adequate PRA or set of design basis accidents to enable establishing the safety classification of its SSCs. While all SSCs used to comply with the general design criteria (GDCs) will be safety related, the intent is to limit the instrumentation risk significance through effective design and reliance on inherent passive safety characteristics. For example, FHRs have no safety-significant temperature threshold phenomena, thus enabling the primary and reserve reactivity control systems required by GDC 26 to be passively, thermally triggered at temperatures well below those for which core or primary coolant boundary damage would occur. Moreover, the passive thermal triggering of the primary and reserve shutdown systems may relegate the control rod drive motors to the control system, substantially decreasing the amount of safety-significant wiring needed. Similarly, FHR decay heat removal systems are intended to be running continuously to minimize the amount of safety-significant instrumentation needed to initiate

OSHA and Experimental Safety Design.

Science.gov (United States)

Sichak, Stephen, Jr.

1983-01-01

Suggests that a governmental agency, most likely Occupational Safety and Health Administration (OSHA) be considered in the safety design stage of any experiment. Focusing on OSHA's role, discusses such topics as occupational health hazards of toxic chemicals in laboratories, occupational exposure to benzene, and role/regulations of other agencies.…

Preliminary safety analysis for key design features of KALIMER with breakeven core

Energy Technology Data Exchange (ETDEWEB)

Hahn, Do Hee; Kwon, Y. M.; Chang, W. P.; Suk, S. D.; Lee, Y. B.; Jeong, K. S

2001-06-01

KAERI is currently developing the conceptual design of a Liquid Metal Reactor, KALIMER (Korea Advanced Liquid MEtal Reactor) under the Long-term Nuclear R and D Program. KALIMER addresses key issues regarding future nuclear power plants such as plant safety, economics, proliferation, and waste. In this report, descriptions of safety design features and safety analyses results for selected ATWS accidents for the breakeven core KALIMER are presented. First, the basic approach to achieve the safety goal is introduced in Chapter 1, and the safety evaluation procedure for the KALIMER design is described in Chapter 2. It includes event selection, event categorization, description of design basis events, and beyond design basis events.In Chapter 3, results of inherent safety evaluations for the KALIMER conceptual design are presented. The KALIMER core and plant system are designed to assure benign performance during a selected set of events without either reactor control or protection system intervention. Safety analyses for the postulated anticipated transient without scram (ATWS) have been performed to investigate the KALIMER system response to the events. In Chapter 4, the design of the KALIMER containment dome and the results of its performance analyses are presented. The design of the existing containment and the KALIMER containment dome are compared in this chapter. Procedure of the containment performance analysis and the analysis results are described along with the accident scenario and source terms. Finally, a simple methodology is introduced to investigate the core energetics behavior during HCDA in Chapter 5. Sensitivity analyses have been performed for the KALIMER core behavior during super-prompt critical excursions, using mathematical formulations developed in the framework of the Modified Bethe-Tait method. Work energy potential was then calculated based on the isentropic fuel expansion model.

Design of a Construction Safety Training System using Contextual Design Methodology

OpenAIRE

Baldev, Darshan H.

2006-01-01

In the U.S., the majority of construction companies are small companies with 10 or fewer employees (BLS, 2004). The fatality rate in the construction industry is high, indicating a need for implementing safety training to a greater extent. This research addresses two main goals: to make recommendations and design a safety training system for small construction companies, and to use Contextual Design to design the training system. Contextual Design was developed by Holtzblatt (Beyer and Holtzb...

Use of a probabilistic safety study in the design of the Italian reference PWR

International Nuclear Information System (INIS)

Richardson, D.C.; Russino, G.; Valentini, V.

1985-01-01

The intent of this paper is to provide a description of the experience gained in having performed a Probabilistic Safety Study (PSS) on the proposed Italian reference pressurized water reactor. The experience revealed that through careful application of probabilistic techniques, Probabilistic Risk Assessment (PRA) can be used as a tool to develop an optimum plant design in terms of safety and cost. Furthermore, the PSS can also be maintained as a living document and a tool to assess additional regulatory requirements that may be imposed during the construction and operational life of the plant. Through the use of flexible probabilistic techniques, the probabilistic safety model can provide a living safety assessment starting from the conceptual design and continuing through the construction, testing and operational phases. Moreover, the probabilistic safety model can be used during the operational phase of the plant as a method to evaluate the operational experience and identify potential problems before they occur. The experience, overall, provided additional insights into the various aspects of the plants design and operation that would not have been identified through the use of traditional safety evaluation techniques

DESIGN PACKAGE 1E SYSTEM SAFETY ANALYSIS

Energy Technology Data Exchange (ETDEWEB)

M. Salem

1995-06-23

The purpose of this analysis is to systematically identify and evaluate hazards related to the Yucca Mountain Project Exploratory Studies Facility (ESF) Design Package 1E, Surface Facilities, (for a list of design items included in the package 1E system safety analysis see section 3). This process is an integral part of the systems engineering process; whereby safety is considered during planning, design, testing, and construction. A largely qualitative approach was used since a radiological System Safety Analysis is not required. The risk assessment in this analysis characterizes the accident scenarios associated with the Design Package 1E structures/systems/components(S/S/Cs) in terms of relative risk and includes recommendations for mitigating all identified risks. The priority for recommending and implementing mitigation control features is: (1) Incorporate measures to reduce risks and hazards into the structure/system/component design, (2) add safety devices and capabilities to the designs that reduce risk, (3) provide devices that detect and warn personnel of hazardous conditions, and (4) develop procedures and conduct training to increase worker awareness of potential hazards, on methods to reduce exposure to hazards, and on the actions required to avoid accidents or correct hazardous conditions.

Model-based safety analysis of a control system using Simulink and Simscape extended models

Directory of Open Access Journals (Sweden)

Shao Nian

2017-01-01

Full Text Available The aircraft or system safety assessment process is an integral part of the overall aircraft development cycle. It is usually characterized by a very high timely and financial effort and can become a critical design driver in certain cases. Therefore, an increasing demand of effective methods to assist the safety assessment process arises within the aerospace community. One approach is the utilization of model-based technology, which is already well-established in the system development, for safety assessment purposes. This paper mainly describes a new tool for Model-Based Safety Analysis. A formal model for an example system is generated and enriched with extended models. Then, system safety analyses are performed on the model with the assistance of automation tools and compared to the results of a manual analysis. The objective of this paper is to improve the increasingly complex aircraft systems development process. This paper develops a new model-based analysis tool in Simulink/Simscape environment.

The Role of Probabilistic Design Analysis Methods in Safety and Affordability

Science.gov (United States)

Safie, Fayssal M.

2016-01-01

For the last several years, NASA and its contractors have been working together to build space launch systems to commercialize space. Developing commercial affordable and safe launch systems becomes very important and requires a paradigm shift. This paradigm shift enforces the need for an integrated systems engineering environment where cost, safety, reliability, and performance need to be considered to optimize the launch system design. In such an environment, rule based and deterministic engineering design practices alone may not be sufficient to optimize margins and fault tolerance to reduce cost. As a result, introduction of Probabilistic Design Analysis (PDA) methods to support the current deterministic engineering design practices becomes a necessity to reduce cost without compromising reliability and safety. This paper discusses the importance of PDA methods in NASA's new commercial environment, their applications, and the key role they can play in designing reliable, safe, and affordable launch systems. More specifically, this paper discusses: 1) The involvement of NASA in PDA 2) Why PDA is needed 3) A PDA model structure 4) A PDA example application 5) PDA link to safety and affordability.

Design and qualification of HPD based designs for safety systems

International Nuclear Information System (INIS)

Sharma, Mukesh Kr.; Chavan, Madhavi A.; Sawhney, Pratibha A.; Mohanty, Ashutos; John, Ajith K.; Ganesh, G.

2014-01-01

Field Programmable Gate Arrays (FPGA) and Complex Programmable Logic Devices (CPLD) are increasingly being used in C and I system of NPPs. The function of such an integrated circuit is not defined by the supplier of the physical component or micro-electronic technology but by the C and I designer. The hardware subsystems implemented in these devices typically use Hardware Description Language (HDL) like VHDL or Verilog to describe the functionality at the design entry level. These circuits are commonly known as 'HDL-Programmed Devices', (HPD). RCnD has developed a set of hardware boards to be used in next generation C and I systems. The boards have been designed based on present day technology and components. The intelligence of these boards has been implemented in HPDs (FPGA/CPLD) using VHDL. Since these boards are used in the safety and safety related systems, they have undergone a rigorous V and V process and qualification tests. This paper discusses the design attributes and qualification of these HPD based designs for nuclear class safety systems. (author)

NUCLEAR SAFETY DESIGN BASES FOR LICENSE APPLICATION

International Nuclear Information System (INIS)

Garrett, R.J.

2005-01-01

The purpose of this report is to identify and document the nuclear safety design requirements that are specific to structures, systems, and components (SSCs) of the repository that are important to safety (ITS) during the preclosure period and to support the preclosure safety analysis and the license application for the high-level radioactive waste (HLW) repository at Yucca Mountain, Nevada. The scope of this report includes the assignment of nuclear safety design requirements to SSCs that are ITS and does not include the assignment of design requirements to SSCs or natural or engineered barriers that are important to waste isolation (ITWI). These requirements are used as input for the design of the SSCs that are ITS such that the preclosure performance objectives of 10 CFR 63.111 [DIRS 156605] are met. The natural or engineered barriers that are important to meeting the postclosure performance objectives of 10 CFR 63.113 [DIRS 156605] are identified as ITWI. Although a structure, system, or component (SSC) that is ITS may also be ITWI, this report is only concerned with providing the nuclear safety requirements for SSCs that are ITS to prevent or mitigate event sequences during the repository preclosure period

Design aspects of radiological safety in nuclear facilities

International Nuclear Information System (INIS)

Patkulkar, D.S.; Purohit, R.G.; Tripathi, R.M.

2014-01-01

In order to keep operational performance of a nuclear facility high and to keep occupational and public exposure ALARA, radiological safety provisions must be reviewed at the time of facility design. Deficiency in design culminates in deteriorated system performance and non adherence to safety standards and could sometimes result in radiological incident. Important radiological aspects relevant to safety were compiled based on operating experiences, design deficiencies brought out from past nuclear incidents, experience gained during maintenance, participation in design review of upcoming nuclear facilities and radiological emergency preparedness

Relevant safety issues in designing the HTR-10 reactor

International Nuclear Information System (INIS)

Sun Yuliang; Xu Yuanghui

2001-01-01

The HTR-10 is a 10 MWth pebble bed high temperature gas cooled reactor being constructed as a research facility at the Institute of Nuclear Energy Technology. This paper discusses design issues of the HTR-10 which are related to safety. It addresses the safety criteria used in the development and assessment of the design, the safety important systems, and the safety classification of components. It also summarises the results of safety analysis, including the approach used for the radioactive source term, as well as the approach to containment design. (author)

Safety and environmental requirements and design targets for TIBER-II

International Nuclear Information System (INIS)

Piet, S.J.

1987-09-01

A consistent set of safety and environmental requirements and design targets was proposed and adopted for the TIBER-II (Tokamak Ignition/Burn Experimental Reactor) design effort. TIBER-II is the most recent US version of a fusion experimental test reactor (ETR). These safety and environmental design targets were one contribution of the Fusion Safety Program in the TIBER-II design effort. The other contribution, safety analyses, is documented in the TIBER-II design report. The TIBER-II approach, described here, concentrated on logical development of, first, a complete and consistent set of safety and environmental requirements that are likely appropriate for an ETR, and, second, an initial set of design targets to guide TIBER-II. Because of limited time in the TIBER-II design effort, the iterative process only included one iteration - one set of targets and one design. Future ETR design efforts should therefore build on these design targets and the associated safety analyses. 29 refs., 5 figs., 3 tabs

Environmental, health, and safety by design

International Nuclear Information System (INIS)

Soklow, R.G.

1999-01-01

Solar Turbines Incorporated created a self-directed work team, the Safety and Environmental Awareness (SEA) Team that initiated a company wide effort to raise employee awareness to promote integrating responsible environmental, health, and safety practices into product design, manufacturing, and services. Environmental, health, and safety issues influence how all businesses operate around the world. Companies choose to operate in an environmentally responsible manner because it not only benefits employees and the communities where they live, it also benefits the business when superior performance results in a competitive advantage. Solar surveyed gas turbines users to identify their top environmental and safety concerns and issues. The authors asked about various environmental and safety aspects of their equipment. Results from the survey has helped engineering and design focus efforts so that future products and product improvements assist customers in meeting their regulatory obligations and social responsibilities. Air pollution has historically been one of the most important environmental issues facing customers, because pollutant emissions greatly influence equipment choices and operation flexibility. There are other environmental, health and safety issues: sustainable fire suppression choices, start systems, hazardous materials use and ability to recycle materials, package accessibility, noise and product take back issues

Mathematical modeling of efficacy and safety for anticancer drugs clinical development.

Science.gov (United States)

Lavezzi, Silvia Maria; Borella, Elisa; Carrara, Letizia; De Nicolao, Giuseppe; Magni, Paolo; Poggesi, Italo

2018-01-01

Drug attrition in oncology clinical development is higher than in other therapeutic areas. In this context, pharmacometric modeling represents a useful tool to explore drug efficacy in earlier phases of clinical development, anticipating overall survival using quantitative model-based metrics. Furthermore, modeling approaches can be used to characterize earlier the safety and tolerability profile of drug candidates, and, thus, the risk-benefit ratio and the therapeutic index, supporting the design of optimal treatment regimens and accelerating the whole process of clinical drug development. Areas covered: Herein, the most relevant mathematical models used in clinical anticancer drug development during the last decade are described. Less recent models were considered in the review if they represent a standard for the analysis of certain types of efficacy or safety measures. Expert opinion: Several mathematical models have been proposed to predict overall survival from earlier endpoints and validate their surrogacy in demonstrating drug efficacy in place of overall survival. An increasing number of mathematical models have also been developed to describe the safety findings. Modeling has been extensively used in anticancer drug development to individualize dosing strategies based on patient characteristics, and design optimal dosing regimens balancing efficacy and safety.

Conceptual design study for the demonstration reactor of JSFR. (3) Safety design and evaluation

International Nuclear Information System (INIS)

Tani, Akihiro; Shimakawa, Yoshio; Kubo, Shigenobu; Fujimura, Ken; Yamano, Hidemasa

2011-01-01

This paper describes the result of conceptual safety design and evaluation for the demonstration plant of Japan sodium-cooled fast reactor (JSFR), which was preliminarily conducted for providing information necessary to decide the plant specification for further design study. The plant major specifications except for output power and safety design concept are almost the same as those of the commercial JSFR. A set of safety evaluation for typical design basis events (DBEs) is mainly focused here, which was conducted for the 750 MWe design. Safety analyses for DBEs evaluation were performed on the basis of conservative assumptions using a one-dimensional flow network code with point kinetics. For representative DBEs, transient over power type events and loss of flow type events were analyzed. The long-term loss-of-offsite power event was also calculated to evaluate the natural circulation decay heat removal system. All analytical results showed to meet tentative safety criteria, thus it was confirmed that the safety design concept of JSFR is feasible against DBEs. (author)

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Russian Edition); Bezopasnost' atomnykh ehlektrostantsij: proektirovanie. Konkretnye trebovaniya bezopasnosti

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-04-15

This publication is a revision of Safety Requirements No. NS-R-1, Safety of Nuclear Power Plants: Design. It establishes requirements applicable to the design of nuclear power plants and elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. It will be useful for organizations involved in the design, manufacture, construction, modification, maintenance, operation and decommissioning of nuclear power plants, as well as for regulatory bodies. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Multinational Design Evaluation Programme (MDEP) - Safety Goals

International Nuclear Information System (INIS)

Vaughan, G.J.

2011-01-01

One of the aims of the NEA's Multinational Design Evaluation Programme (MDEP) is to work towards greater harmonisation of regulatory requirements. To achieve this aim, it is necessary that there is a degree of convergence on the safety goals that are required to be met by designers and operators. The term 'safety goals' is defined to cover all health and safety requirements which must be met: these may be deterministic rules and/or probabilistic targets. They should cover the safety of workers, public and the environment in line with the IAEA's Basic Safety Objective; encompassing safety in normal operation through to severe accidents. MDEP is also interested in how its work can be extended to future reactors, which may use significantly different technology to the almost ubiquitous LWRs used today and in the next generation, building on the close co-operation within MDEP between the regulators who are currently engaged in constructing or carrying out design reviews on new designs. For two designs this work has involved several regulators sharing their safety assessments and in some cases issuing statements on issues that need to be addressed. Work is also progressing towards joint regulatory position statements on specific assessment areas. Harmonisation of safety goals will enhance the cooperation between regulators as further developments in design and technology occur. All regulators have safety goals, but these are expressed in many different ways and exercises in comparing them frequently are done at a very low level eg specific temperatures in the reactor vessel of a specific reactor type. The differences in the requirements from different regulators are difficult to resolve as the goals are derived using different principles and assumptions and are often for a specific technology. Therefore a different approach is being investigated, starting with the top-level safety goals and try to derive a structure and means of deriving lower tier

Nuclear Safety Design Base for License Application

International Nuclear Information System (INIS)

R.J. Garrett

2005-01-01

The purpose of this report is to identify and document the nuclear safety design requirements that are specific to structures, systems, and components (SSCs) of the repository that are important to safety (ITS) during the preclosure period and to support the preclosure safety analysis and the license application for the high-level radioactive waste (HLW) repository at Yucca Mountain, Nevada. The scope of this report includes the assignment of nuclear safety design requirements to SSCs that are ITS and does not include the assignment of design requirements to SSCs or natural or engineered barriers that are important to waste isolation (ITWI). These requirements are used as input for the design of the SSCs that are ITS such that the preclosure performance objectives of 10 CFR 63.111(b) [DIRS 173273] are met. The natural or engineered barriers that are important to meeting the postclosure performance objectives of 10 CFR 63.113(b) and (c) [DIRS 173273] are identified as ITWI. Although a structure, system, or component (SSC) that is ITS may also be ITWI, this report is only concerned with providing the nuclear safety requirements for SSCs that are ITS to prevent or mitigate event sequences during the repository preclosure period

Working Towards Unified Safety Design Criteria for Modular High Temperature Gas-cooled Reactor Designs

International Nuclear Information System (INIS)

Reitsma, Frederik; Silady, Fred; Kunitomi, Kazuhiko

2014-01-01

The Nuclear Power Development Section of the IAEA recently received approval for a Coordinated Research Project (CRP) to investigate and make proposals on modular High Temperature Gas-cooled Reactor (HTGR) Safety design criteria. It is expected that these criteria would consider past experience and existing safety standards in the light of modular HTGR material and design characteristics to propose safety design criteria. It will consider the deterministic and risk-informed safety design standards that apply to the wide spectrum of Off- normal events under development worldwide for existing and planned HTGRs. The CRP would also take into account lessons from the Fukushima Daiichi accident, clarifying the safety approach and safety evaluation criteria for design and beyond design basis events, including those events that can affect multiple reactor modules and/or are dependent on the application proximate to the plant site. (e. g., industrial process steam/heat). The logical flow of criteria is from the fundamental inherent safety characteristics of modular HTGRs and associated expected performance characteristics, to the safety functions required to ensure those characteristics during the wide spectrum of Off-normal events, and finally to specific criteria related to those functions. This is detailed in the paper with specific examples included of how it may be applied. The results of the CRP will be made available to the member states and HTGR community. (author)

Safety assessment in plant layout design using indexing approach: Implementing inherent safety perspective

International Nuclear Information System (INIS)

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-01-01

The design of layout plans requires adequate assessment tools for the quantification of safety performance. The general focus of the present work is to introduce an inherent safety perspective at different points of the layout design process. In particular, index approaches for safety assessment and decision-making in the early stages of layout design are developed and discussed in this two-part contribution. Part 1 (accompanying paper) of the current work presents an integrated index approach for safety assessment of early plant layout. In the present paper (Part 2), an index for evaluation of the hazard related to the potential of domino effects is developed. The index considers the actual consequences of possible escalation scenarios and scores or ranks the subsequent accident propagation potential. The effects of inherent and passive protection measures are also assessed. The result is a rapid quantification of domino hazard potential that can provide substantial support for choices in the early stages of layout design. Additionally, a case study concerning selection among various layout options is presented and analyzed. The case study demonstrates the use and applicability of the indices developed in both parts of the current work and highlights the value of introducing inherent safety features early in layout design

Design of disturbances control model at automotive company

Science.gov (United States)

Marie, I. A.; Sari, D. K.; Astuti, P.; Teorema, M.

2017-12-01

The discussion was conducted at PT. XYZ which produces automotive components and motorcycle products. The company produced X123 type cylinder head which is a motor vehicle forming component. The disturbances in the production system has affected the company performance in achieving the target of Key Performance Indicator (KPI). Currently, the determination of the percentage of safety stock of cylinder head products is not in accordance to the control limits set by the company (60% - 80%), and tends to exceed the control limits that cause increasing the inventory wastage in the company. This study aims to identify the production system disturbances that occurs in the production process of manufacturing components of X123 type cylinder head products and design the control model of disturbance to obtain control action and determine the safety stock policy in accordance with the needs of the company. The design stage has been done based on the Disturbance Control Model which already existing and customized with the company need in controlling the production system disturbances at the company. The design of the disturbances control model consists of sub-model of the risk level of the disturbance, sub-model of action status, sub-model action control of the disturbance, and sub-model of determining the safety stock. The model can assist the automotive company in taking the decision to perform the disturbances control action in production system cylinder head while controlling the percentage of the safety stock.

Safety and design limits

International Nuclear Information System (INIS)

Shishkov, L. K.; Gorbaev, V. A.; Tsyganov, S. V.

2007-01-01

The paper touches upon the issues of NPP safety ensuring at the stage of fuel load design and operation by applying special limitations for a series of parameters, that is, design limits. Two following approaches are compared: the one used by west specialists for the PWR reactor and the Russian approach employed for the WWER reactor. The closeness of approaches is established, differences that are mainly peculiarities of terms are noted (Authors)

The approaches of safety design and safety evaluation at HTTR (High Temperature Engineering Test Reactor)

International Nuclear Information System (INIS)

Iigaki, Kazuhiko; Saikusa, Akio; Sawahata, Hiroaki; Shinozaki, Masayuki; Tochio, Daisuke; Honma, Fumitaka; Tachibana, Yukio; Iyoku, Tatsuo; Kawasaki, Kozo; Baba, Osamu

2006-06-01

Gas Cooled Reactor has long history of nuclear development, and High Temperature Gas Cooled Reactor (HTGR) has been expected that it can be supply high temperature energy to chemical industry and to power generation from the points of view of the safety, the efficiency, the environment and the economy. The HTGR design is tried to installed passive safety equipment. The current licensing review guideline was made for a Low Water Reactor (LWR) on safety evaluation therefore if it would be directly utilized in the HTGR it needs the special consideration for the HTGR. This paper describes that investigation result of the safety design and the safety evaluation traditions for the HTGR, comparison the safety design and safety evaluation feature for the HTGT with it's the LWR, and reflection for next HTGR based on HTTR operational experiment. (author)

ARIES-AT safety design and analysis

Energy Technology Data Exchange (ETDEWEB)

Petti, D.A. [Idaho National Engineering and Environmental Laboratory, Fusion Safety Program, P.O. Box 1625, Idaho Falls, ID 83415 (United States)]. E-mail: David.Petti@inl.gov; Merrill, B.J. [Idaho National Engineering and Environmental Laboratory, Fusion Safety Program, P.O. Box 1625, Idaho Falls, ID 83415 (United States); Moore, R.L. [Idaho National Engineering and Environmental Laboratory, Fusion Safety Program, P.O. Box 1625, Idaho Falls, ID 83415 (United States); Longhurst, G.R. [Idaho National Engineering and Environmental Laboratory, Fusion Safety Program, P.O. Box 1625, Idaho Falls, ID 83415 (United States); El-Guebaly, L. [Fusion Technology Institute, 1500 Engineering Drive, University of Wisconsin-Madison, Madison, WI 53706 (United States); Mogahed, E. [Fusion Technology Institute, 1500 Engineering Drive, University of Wisconsin-Madison, Madison, WI 53706 (United States); Henderson, D. [Fusion Technology Institute, 1500 Engineering Drive, University of Wisconsin-Madison, Madison, WI 53706 (United States); Wilson, P. [Fusion Technology Institute, 1500 Engineering Drive, University of Wisconsin-Madison, Madison, WI 53706 (United States); Abdou, A. [Fusion Technology Institute, 1500 Engineering Drive, University of Wisconsin-Madison, Madison, WI 53706 (United States)

2006-01-15

ARIES-AT is a 1000 MWe conceptual fusion power plant design with a very low projected cost of electricity. The design contains many innovative features to improve both the physics and engineering performance of the system. From the safety and environmental perspective, there is greater depth to the overall analysis than in past ARIES studies. For ARIES-AT, the overall spectrum of off-normal events to be examined has been broadened. They include conventional loss of coolant and loss of flow events, an ex-vessel loss of coolant, and in-vessel off-normal events that mobilize in-vessel inventories (e.g., tritium and tokamak dust) and bypass primary confinement such as a loss of vacuum and an in-vessel loss of coolant with bypass. This broader examination of accidents improves the robustness of the design from the safety perspective and gives additional confidence that the facility can meet the no-evacuation requirement under average weather conditions. We also provide a systematic assessment of the design to address key safety functions such as confinement, decay heat removal, and chemical energy control. In the area of waste management, both the volume of the component and its hazard are used to classify the waste. In comparison to previous ARIES designs, the overall waste volume is less because of the compact design.

Validation of a functional model for integration of safety into process system design

DEFF Research Database (Denmark)

Wu, J.; Lind, M.; Zhang, X.

2015-01-01

with the process system functionalities as required for the intended safety applications. To provide the scientific rigor and facilitate the acceptance of qualitative modelling, this contribution focuses on developing a scientifically based validation method for functional models. The Multilevel Flow Modeling (MFM...

Panel 1: Safety design criteria

International Nuclear Information System (INIS)

Yllera, Javier

2013-01-01

There is general consensus in the nuclear community, and more after the Fukushima accident, that the deployment of nuclear energy has to be done at the highest levels of nuclear safety and that safety cannot be compromised by other factors. It is well understood that reactors that are being licensed and the new generations of reactors that will be constructed in the future will need to reach higher safety levels than the existing ones. Several countries and international organizations or international groups are launching initiatives to harmonise safety goals, safety requirements, safety objectives, regulations, criteria or safety reference levels. There are differences in the meanings of these terms and the working approaches, but the overall purpose is the same: to specify how new plants can be safer. In this context, the IAEA has an statutory function for developing international nuclear safety standards. The IAEA safety standards are per se not mandatory for IAEA Member States. Regulating safety is a national responsibility, and many States have decided to adopt the IAEA’s standards for use in their national regulations in different ways. The IAEA Safety Standards represent international consensus on what must constitute a high level of safety for nuclear installations. In the area of NPP design, IAEA safety standards that are published are intended to apply primarily to new plants. It might not be practicable to apply all the requirements to plants that are already in operation. In addition, the focus is primarily on plants with water cooled reactors

Safety research needs for Russian-designed reactors

International Nuclear Information System (INIS)

1998-01-01

In June 1995, an OECD Support Group was set up to perform a broad study of the safety research needs of Russian-designed reactors. This Support Group was endorsed by the CSNI. The Support Group, which is composed of senior experts on safety research from several OECD countries and from Russia, prepared this Report. The Group reviewed the safety research performed to support Russian-designed reactors and set down its views on future needs. The review concentrates on the following main topics: Thermal-Hydraulics/Plant Transients for VVERs; Integrity of Equipment and Structures for VVERs; Severe Accidents for VVERs; Operational Safety Issues; Thermal-Hydraulics/Plant Transients for RBMKs; Integrity of Equipment and Structures for RBMKs; Severe Accidents for RBMKs. (K.A.)

PSA in design of passive/active safety reactors

International Nuclear Information System (INIS)

Sato, T.; Tanabe, A.; Kondo, S.

1995-01-01

PSAs in the design of advanced reactors are applied mainly in level 1 PSA areas. However, even in level 1 PSA, there are certain areas where special care must be taken depending on plant design concepts. This paper identifies these areas both for passive and active safety reactor concepts. For example, 'long-term PSA' and shutdown PSA are very important for a passive safety reactor concept from the standpoint of effectiveness of a grace period and passive safety systems. External events are also important for an active safety reactor concept. These kinds of special PSAs are difficult to conduct precisely in a conceptual design stage. This paper shows methods of conducting these kinds of special PSAs simply and conveniently and the use of acquired insights for the design of advanced reactors. This paper also clarifies the meaning or definition of a grace period from the standpoint of PSA

Safety design integrated in the building delivery system

DEFF Research Database (Denmark)

Jørgensen, Kirsten

2013-01-01

. The purpose of this article is to demonstrate how safety and health can be integrated in the design phases integrated in the management delivery systems within construction, The method for the research was to go through the building delivery system step by step and create a normative description of what, when......In construction, it is important to view safety and health as an integrated part of the way that “designers” are working. The designers cowers architects, constructors, engineers and others who carry out their consulting services in the design phase of a construction project. The philosophy...... and how to fully integrate safety in each part of the process. The result is a concept and guideline including control forms for how to integrate safety design in the Building Delivery System plus what to do and when. The concept has been tested in an educational context. The practical value...

The reactor safety study of experimental multi-purpose VHTR design

International Nuclear Information System (INIS)

Yasuno, T.; Mitake, S.; Ezaki, M.; Suzuki, K.

1981-01-01

Over the past years, the design works of the Experimental Very High Temperature Reactor (VHTR) plant have been conducted at Japan Atomic Energy Research Institute. The conceptual design has been completed and the more detailed design works and the safety analysis of the experimental VHTR plant are continued. The purposes of design studies are to show the feasibility of the experimental VHTR program, to specify the characteristics and functions of the plant components, to point out the R and D items necessary for the experimental VHTR plant construction, and to analyze the feature of the plant safety. In this paper the summary of system design and safety features of the experimental reactor are indicated. Main issues are the safety philosophy for the design basis accident, the accidents assumed and the engineered safety systems adopted in the design works

LABORATORY DESIGN CONSIDERATIONS FOR SAFETY.

Science.gov (United States)

National Safety Council, Chicago, IL. Campus Safety Association.

THIS SET OF CONSIDERATIONS HAS BEEN PREPARED TO PROVIDE PERSONS WORKING ON THE DESIGN OF NEW OR REMODELED LABORATORY FACILITIES WITH A SUITABLE REFERENCE GUIDE TO DESIGN SAFETY. THERE IS NO DISTINCTION BETWEEN TYPES OF LABORATORY AND THE EMPHASIS IS ON GIVING GUIDES AND ALTERNATIVES RATHER THAN DETAILED SPECIFICATIONS. AREAS COVERED INCLUDE--(1)…

Design trade-offs in view of safety considerations

International Nuclear Information System (INIS)

Saji, G.; Kishida, K.; Inoue, T.

1978-01-01

In view of resolving conflicting demands of cost, safety, flexibility of operation and design margins, safety design of various plant systems is discussed referring to their weight on construction costs. An influence of hypothetical core disruptive accident (HCDA) and loss of piping integrity (LOPI) on plant design and thus on construction materials is discussed, in optimising future commercial FBR plants. (author)

The enhancement of Ignalina NPP in design and operational safety

International Nuclear Information System (INIS)

Negrivoda, G.

1999-01-01

Enhancement of Ignalina NPP design include: core design improvements; fuel channel integrity (multiple pressure tube rupture); improvements of shutdown systems; improvements of instrumentation and control devices; containment strength and tightness; design basis accident analysis; improvements of safety and support systems; seismic safety enhancement; Year 2000 project; cracks in pipes. Enhancement of operational safety includes: quality assurance; configuration management; safety management and safety culture; emergency operating procedures; training and full scope simulator; in-service inspection; fire protection and ageing monitoring and management

Status of conceptual safety design study of Japanese sodium-cooled fast reactor

International Nuclear Information System (INIS)

Kubo, Shigenobu; Kurisaka, Kenichi; Niwa, Hajime; Shimakawa, Yoshio

2005-01-01

In this paper, the current conceptual safety design and related evaluation of Japanese Sodium-cooled Fast Reactor which is studied in the framework of the Feasibility Study (FS) on commercialized Fast Reactor Cycle Systems in Japan are described. The purpose of the safety design is to establish a feasible safety concept of FBR which aims at a sustainable energy source of the next generations. The safety targets and the safety design principle are set aiming at realizing worldwide acceptability of the safety level. The basic safety design concept, which can meet the safety targets, was formulated taking along with the defense-in-depth philosophy as the basic safety design principle. In order to cope with wide range of energy and resource demands, there are some various designs both of oxide and metal fuel for JSFR. Some analytical results of typical design basis events, design extension conditions and core damage frequency estimation show the feasibility of the safety design concept for them. (author)

Enhanced CANDU 6 design assist probabilistic safety assessment results and insights

International Nuclear Information System (INIS)

Torabi, T.; Bettig, R.; Iliescu, P.; Robinson, J.; Santamaura, P.; Skorupska, B.; Tyagi, A.K.; Vencel, I.

2013-01-01

The Enhanced CANDU 6(EC6) is a 700 MWe reactor, which has evolved from the well-established CANDU line of reactors, which are heavy-water moderated, and heavy-water cooled horizontal pressure tube reactors, using natural uranium fuel. The EC6 design retains the generic CANDU design features, while incorporating innovations and state-of-the-art technologies to ensure competitiveness with other design with respect to operation, performance and economics. A design assist probabilistic safety assessment (PSA) was conducted during the design change phase of the project. The purpose of the assessment was to assess internal events during at-power operation and identify the design improvements and additional features needed to comply with the latest regulatory requirements in Canada and compete with other reactor designs, internationally. The PSA results show that the EC6 plant response to the postulated initiating events is well balanced, and the design meets its safety objectives. This paper summarizes the results and insights gained during the development of the PSA models for at-power internal events. (author)

Safety design philosophy of gas turbine high temperature reactor (GTHTR300)

International Nuclear Information System (INIS)

Katanishi, Shoji; Kunitomi, Kazuhiko

2003-01-01

Japan Atomic Energy Research Institute has been developing design studies of the Gas Turbine High Temperature Reactor (GTHTR300). The original safety design philosophy has also been discussed and fixed for the GTHTR300. One of the unique feature of the safety philosophy of the GTHTR300 is that a depressurization accident is postulated as a design basis accident in order to show the high level of safety characteristics, though its probability of occurrence is much lower than the probability range of design basis accident. Another feature of safety design is to adopt a double confinement that is one of the original concepts for the GTHTR300. By using a double confinement, a feasibility of safety design without containment vessel was clarified even in case of a depressurization accident. This article describes the safety design philosophy and some results of preliminary evaluations which were conducted in order to clarify the feasibility of original safety design of the GTHTR300. (author)

Toward the modelling of safety violations in healthcare systems.

Science.gov (United States)

Catchpole, Ken

2013-09-01

When frontline staff do not adhere to policies, protocols, or checklists, managers often regard these violations as indicating poor practice or even negligence. More often than not, however, these policy and protocol violations reflect the efforts of well intentioned professionals to carry out their work efficiently in the face of systems poorly designed to meet the diverse demands of patient care. Thus, non-compliance with institutional policies and protocols often signals a systems problem, rather than a people problem, and can be influenced among other things by training, competing goals, context, process, location, case complexity, individual beliefs, the direct or indirect influence of others, job pressure, flexibility, rule definition, and clinician-centred design. Three candidates are considered for developing a model of safety behaviour and decision making. The dynamic safety model helps to understand the relationship between systems designs and human performance. The theory of planned behaviour suggests that intention is a function of attitudes, social norms and perceived behavioural control. The naturalistic decision making paradigm posits that decisions are based on a wider view of multiple patients, expertise, systems complexity, behavioural intention, individual beliefs and current understanding of the system. Understanding and predicting behavioural safety decisions could help us to encourage compliance to current processes and to design better interventions.

SAFETY IN THE DESIGN OF SCIENCE LABORATORIES AND BUILDING CODES.

Science.gov (United States)

HOROWITZ, HAROLD

THE DESIGN OF COLLEGE AND UNIVERSITY BUILDINGS USED FOR SCIENTIFIC RESEARCH AND EDUCATION IS DISCUSSED IN TERMS OF LABORATORY SAFETY AND BUILDING CODES AND REGULATIONS. MAJOR TOPIC AREAS ARE--(1) SAFETY RELATED DESIGN FEATURES OF SCIENCE LABORATORIES, (2) LABORATORY SAFETY AND BUILDING CODES, AND (3) EVIDENCE OF UNSAFE DESIGN. EXAMPLES EMPHASIZE…

Safety aspects and shield design of a Poton irradiator

International Nuclear Information System (INIS)

Mehta, S.K.; Nayak, A.R.; Bongirwar, D.R.; Modi, R.K.; Ramkumar, M.S.

1998-01-01

An irradiation plant, POTON, for irradiation of potatoes and onions is being set up at Nashik. Shield design and safety features of this plant incorporate some novel and innovative features like a compact cell, curved cell boundaries for smooth conveyor movement though the cell labyrinth and conform to ICRP and AERB design safety requirements. The safety features include multiple safety interlocks, audio-visual alarms, scram switches and trip wire for avoiding accidental exposures. (author)

Preliminary safety analysis for key design features of KALIMER

Energy Technology Data Exchange (ETDEWEB)

Hahn, D. H.; Kwon, Y. M.; Chang, W. P.; Suk, S. D.; Lee, S. O.; Lee, Y. B.; Jeong, K. S

2000-07-01

KAERI is currently developing the conceptual design of a liquid metal reactor, KALIMER(Korea Advanced Liquid Metal Reactor) under the long-term nuclear R and D program. In this report, descriptions of the KALIMER safety design features and safety analyses results for selected ATWS accidents are presented. First, the basic approach to achieve the safety goal is introduced in chapter 1, and the safety evaluation procedure for the KALIMER design is described in chapter 2. It includes event selection, event categorization, description of design basis events, and beyond design basis events. In chapter 3, results of inherent safety evaluations for the KALIMER conceptual design are presented. The KALIMER core and plant system are designed to assure design performance during a selected set of events without either reactor control or protection system intervention. Safety analyses for the postulated anticipated transient without scram(ATWS) have been performed to investigate the KALIMER system response to the events. They are categorized as bounding events(BEs) because of their low probability of occurrence. In chapter 4, the design of the KALIMER containment dome and the results of its performance analysis are presented. The designs of the existing LMR containment and the KALIMER containment dome have been compared in this chapter. Procedure of the containment performance analysis and the analysis results are described along with the accident scenario and source terms. Finally, a simple methodology is introduced to investigate the core kinetics and hydraulic behavior during HCDA in chapter 5. Mathematical formulations have been developed in the framework of the modified bethe-tait method, and scoping analyses have been performed for the KALIMER core behavior during super-prompt critical excursions.

Balanced Design of Safety Systems of CAREM Advanced Reactor

International Nuclear Information System (INIS)

Grinblat, Pablo; Gimenez, Marcelo; Schlamp, Miguel

2003-01-01

Nuclear Power Plants must meet the performance that the market and the population demand in order to be part of the electricity supply industry.It is related mainly with the results of reactor's economy and safety.New advances in the methodology developed for reactor economic optimization analyzing its safety at an early engineering stage, aiming at balancing these important features of the design, are presented in this work.In particular, the coupling that appears when dimensioning the Emergency Injection System, the Residual Heat Removal System and the containment height of CAREM reactor is described.The new models appended to the computer code that embodies the methodology to balance de designs are shown.Finally the results obtained with the optimizations when applying it are presented.Furthermore, a criterion to establish the maximal diameter for acceptable breaks in RPV's penetrations arises from this work.The application of the methodology and the computer code developed turns out to prove the advantages they provide to reactor design so that the plants are properly balanced and optimized

Advanced gas cooled reactors - Designing for safety

International Nuclear Information System (INIS)

Keen, Barry A.

1990-01-01

The Advanced Gas-Cooled Reactor Power Stations recently completed at Heysham in Lancashire, England, and Torness in East Lothian, Scotland represent the current stage of development of the commercial AGR. Each power station has two reactor turbo-generator units designed for a total station output of 2x660 MW(e) gross although powers in excess of this have been achieved and it is currently intended to uprate this as far as possible. The design of both stations has been based on the successful operating AGRs at Hinkley Point and Hunterston which have now been in-service for almost 15 years, although minor changes were made to meet new safety requirements and to make improvements suggested by operating experience. The construction of these new AGRs has been to programme and within budget. Full commercial load for the first reactor at Torness was achieved in August 1988 with the other three reactors following over the subsequent 15 months. This paper summarises the safety principles and guidelines for the design of the reactors and discusses how some of the main features of the safety case meet these safety requirements. The paper also summarises the design problems which arose during the construction period and explains how these problems were solved with the minimum delay to programme

Advanced gas cooled reactors - Designing for safety

Energy Technology Data Exchange (ETDEWEB)

Keen, Barry A [Engineering Development Unit, NNC Limited, Booths Hall, Knutsford, Cheshire (United Kingdom)

1990-07-01

The Advanced Gas-Cooled Reactor Power Stations recently completed at Heysham in Lancashire, England, and Torness in East Lothian, Scotland represent the current stage of development of the commercial AGR. Each power station has two reactor turbo-generator units designed for a total station output of 2x660 MW(e) gross although powers in excess of this have been achieved and it is currently intended to uprate this as far as possible. The design of both stations has been based on the successful operating AGRs at Hinkley Point and Hunterston which have now been in-service for almost 15 years, although minor changes were made to meet new safety requirements and to make improvements suggested by operating experience. The construction of these new AGRs has been to programme and within budget. Full commercial load for the first reactor at Torness was achieved in August 1988 with the other three reactors following over the subsequent 15 months. This paper summarises the safety principles and guidelines for the design of the reactors and discusses how some of the main features of the safety case meet these safety requirements. The paper also summarises the design problems which arose during the construction period and explains how these problems were solved with the minimum delay to programme.

A total safety management model

International Nuclear Information System (INIS)

Obadia, I.J.; Vidal, M.C.R.; Melo, P.F.F.F.

2002-01-01

In nuclear organizations, quality and safety are inextricably linked. Therefore, the search for excellence means reaching excellence in nuclear safety. The International Atomic Energy Agency, IAEA, developed, after the Chernobyl accident, the organizational approach for improving nuclear safety based on the safety culture, which requires a framework necessary to provide modifications in personnel attitudes and behaviors in situations related to safety. This work presents a Total Safety Management Model, based on the Model of Excellence of the Brazilian Quality Award and on the safety culture approach, which represents an alternative to this framework. The Model is currently under validation at the Nuclear Engineering Institute, in Rio de Janeiro, Brazil, and the results of its initial safety culture self assessment are also presented and discussed. (author)

Safety research needs for Russian-designed reactors. Requirements situation

International Nuclear Information System (INIS)

Brown, R. Allan; Holmstrom, Heikki; Reocreux, Michel; Schulz, Helmut; Liesch, Klaus; Santarossa, Giampiero; Hayamizu, Yoshitaka; Asmolov, Vladimir; Bolshov, Leonid; Strizhov, Valerii; Bougaenko, Sergei; Nikitin, Yuri N.; Proklov, Vladimir; Potapov, Alexandre; Kinnersly, Stephen R.; Voronin, Leonid M.; Honekamp, John R.; Frescura, Gianni M.; Maki, Nobuo; Reig, Javier; ); Bekjord, Eric S.; Rosinger, Herbert E.

1998-01-01

integrity must be verified, and material property data bases extended. - VVER severe accident research should focus on validation of codes for accident management procedures, and on extension and qualification of an appropriate data base for materials properties and their interactions. - RBMK thermal-hydraulic research is needed to improve the technical basis for further development of RBMK safety criteria. - Assessment of the integrity of the RBMK primary coolant circuit, and especially the fuel channel, requires urgent research. Methods of assessing RBMK pressure boundary integrity must be verified, and material property data bases extended. - RBMK severe accident research should focus on prevention of accidents and Accident Management for cases of loss of heat sink and Beyond Design-Basis Loss-of-Coolant Accidents. For these purposes, simple physical models and parametric codes need development and should be systematically used in plant specific analysis. Recommendations; - A Safety Research Strategic Plan should be developed. Such a plan sets goals, defines products, and describes when and how work will be done, including determination of research priorities. - Key players, including regulators, operators, plant designers and researchers should be involved in developing and implementing this plan and its execution and applying the results. - International cooperation in safety research should be encouraged for purposes of improving quality, preventing technical isolation and cost sharing. - New approaches, such as technical fora for specific technical topics, should be established to make safety research information in OECD countries available to researchers working on the safety of Russian-designed reactors

Modeling Safety Barriers and Defense in Depth with Mulitlevel Flow Modeling

DEFF Research Database (Denmark)

Lind, Morten

2012-01-01

in MFM is a barrier function. It is shown that other barrier types can be represented andthat their combination into barrier chains may be used to analyze and design levels of safety in automated processes.Suggestion for further research on barrier modeling with MFM are included....

Integrating Safeguards and Security with Safety into Design

International Nuclear Information System (INIS)

Bean, Robert S.; Hockert, John W.; Hebditch, David J.

2009-01-01

There is a need to minimize security risks, proliferation hazards, and safety risks in the design of new nuclear facilities in a global environment of nuclear power expansion, while improving the synergy of major design features and raising operational efficiency. In 2008, the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA) launched the Next Generation Safeguards Initiative (NGSI) covering many safeguards areas. One of these, launched by NNSA with support of the DOE Office of Nuclear Energy, was a multi-laboratory project, led by the Idaho National Laboratory (INL), to develop safeguards by design. The proposed Safeguards-by-Design (SBD) process has been developed as a structured approach to ensure the timely, efficient, and cost effective integration of international safeguards and other nonproliferation barriers with national material control and accountability, physical security, and safety objectives into the overall design process for the nuclear facility lifecycle. A graded, iterative process was developed to integrate these areas throughout the project phases. It identified activities, deliverables, interfaces, and hold points covering both domestic regulatory requirements and international safeguards using the DOE regulatory environment as exemplar to provide a framework and guidance for project management and integration of safety with security during design. Further work, reported in this paper, created a generalized SBD process which could also be employed within the licensed nuclear industry and internationally for design of new facilities. Several tools for integrating safeguards, safety, and security into design are discussed here. SBD appears complementary to the EFCOG TROSSI process for security and safety integration created in 2006, which focuses on standardized upgrades to enable existing DOE facilities to meet a more severe design basis threat. A collaborative approach is suggested.

Partial Safety Factors for Fatigue Design of Wind Turbine Blades

DEFF Research Database (Denmark)

Toft, Henrik Stensgaard; Sørensen, John Dalsgaard

2010-01-01

In the present paper calibration of partial safety factors for fatigue design of wind turbine blades is considered. The stochastic models for the physical uncertainties on the material properties are based on constant amplitude fatigue tests and the uncertainty on Miners rule for linear damage...... accumulation is determined from variable amplitude fatigue tests with the Wisper and Wisperx spectra. The statistical uncertainty for the assessment of the fatigue loads is also investigated. The partial safety factors are calibrated for design load case 1.2 in IEC 61400-1. The fatigue loads are determined...... from rainflow-counting of simulated time series for a 5MW reference wind turbine [1]. A possible influence of a complex stress state in the blade is not taken into account and only longitudinal stresses are considered....

Key issues on safety design basis selection and safety assessment

International Nuclear Information System (INIS)

An, S.; Togo, Y.

1976-01-01

In current fast reactor design in Japan, four design accident conditions and four design seismic conditions are adopted as the design base classifications. These are classified by the considerations on both likelihood of occurrence and the severeness of the consequences. There are several major problem areas in safety design consideration such as core accident problems which include fuel sodium interaction, fuel failure propagation and residual decay heat removal, and decay heat removal systems problems which is more or less the problem of selection of appropriate system and of assurance of high reliability of the system. In view of licensing, two kinds of accidents are postulated in evaluating the adequacy of a reactor site. The one is the ''major accident'' which is the accident to give most severe radiation hazard to the public from technical point of view. The other is the ''hypothetical accident'', induced public accident of which is severer than that of major accident. While the concept of the former is rather unique to Japanese licensing, the latter is almost equivalent to design base hypothetical accident of the US practice. In this paper, design bases selections, key safety issues and some of the licensing considerations in Japan are described

Novel modular natural circulation BWR design and safety evaluation

International Nuclear Information System (INIS)

Ishii, Mamoru; Shi, Shanbin; Yang, Won Sik; Wu, Zeyun; Rassame, Somboon; Liu, Yang

2015-01-01

Highlights: • Introduction of BWR-type natural circulation small modular reactor preliminary design (NMR-50). • Design of long fuel cycle length for the NMR-50. • Design of double passive safety systems for the NMR-50. • RELAP5 analyses of design basis accidents for the NMR-50. - Abstract: The Purdue NMR (Novel Modular Reactor) represents a BWR-type small modular reactor with a significantly reduced reactor pressure vessel (RPV) height. Specifically, it has one third the height of a conventional BWR RPV with an electrical output of 50 MWe. The preliminary design of the NMR-50 including reactor, fuel cycle, and safety systems is described and discussed. The improved neutronics design of the NMR-50 extends the fuel cycle length up to 10 years. The NMR-50 is designed with double passive engineering safety system, which is intended to withstand a prolonged station black out with loss of ultimate heat sink accident such as experienced at Fukushima. In order to evaluate the safety features of the NMR-50, two representative design basis accidents, i.e. main steam line break (MSLB) and bottom drain line break (BDLB), are simulated by using the best-estimate thermal–hydraulic code RELAP5. The RPV water inventory, containment pressure, and the performance of engineering safety systems are investigated for about 33 h after the initiation of the accidents

Safety design philosophy of gas turbine high temperature reactor (GTHTR300)

International Nuclear Information System (INIS)

Katanishi, Shoji; Kunitomi, Kazuhiko

2003-01-01

Japan Atomic Energy Research Institute (JAERI) has been developing design studies of the Gas Turbine High Temperature Reactor (GTHTR300). The original safety design philosophy has also been discussed and fixed for the GTHTR300 based on the experience of the High Temperature Engineering Test Reactor (HTTR) of JAERI which is the first High Temperature Gas-cooled Reactor (HTGR) in Japan. One of the unique feature of the safety philosophy of the GTHTR300 is that a depressurization accident induced by a large pipe break is postulated as a design basis accident in order to show the high level of safety characteristics, though its probability of occurrence is lower than the probability range of design basis accident. Another feature of safety design is to adopt a double confinement that is one of the original concepts for the GTHTR300. By using a double confinement, a feasibility of safety design without containment vessel was clarified even in case of the depressurization accident. The safety design philosophies for passive cooling system, reactor shutdown system, and so on were determined. The methodology for the safety evaluation, such as safety criteria and selection of events to be evaluated by using estimation of probability of occurrence, were also discussed and determined. This article describes the safety design philosophy and some results of preliminary evaluations which were conducted in order to clarify the feasibility of original safety design of the GTHTR300. The present study is entrusted from Ministry of Education, Culture, Sports, Science and Technology of Japan. (author)

Prevention through Design Adoption Readiness Model (PtD ARM): An integrated conceptual model.

Science.gov (United States)

Weidman, Justin; Dickerson, Deborah E; Koebel, Charles T

2015-01-01

Prevention through Design (PtD), eliminating hazards at the design-stage of tools and systems, is the optimal method of mitigating occupational health and safety risks. A recent National Institute of Safety and Health initiative has established a goal to increase adoption of PtD innovation in industry. The construction industry has traditionally lagged behind other sectors in the adoption of innovation, in general; and of safety and health prevention innovation, in particular. Therefore, as a first step toward improving adoption trends in this sector, a conceptual model was developed to describe the parameters and causal relationships that influence and predict construction stakeholder "adoption readiness" for PtD technology innovation. This model was built upon three well-established theoretical frameworks: the Health Belief Model, the Diffusion of Innovation Model, and the Technology Acceptance Model. Earp and Ennett's model development methodology was employed to build a depiction of the key constructs and directionality and magnitude of relationships among them. Key constructs were identified from the literature associated with the three theoretical frameworks, with special emphasis given to studies related to construction or OHS technology adoption. A conceptual model is presented. Recommendations for future research are described and include confirmatory structural equation modeling of model parameters and relationships, additional descriptive investigation of barriers to adoption in some trade sectors, and design and evaluation of an intervention strategy.

The impact of safety analyses on the design of the Hanford Waste Vitrification Plant

International Nuclear Information System (INIS)

Koppenaal, T.J.; Yee, A.K.; Reisdorf, J.B.; Hall, B.W.

1993-04-01

Accident analyses are being performed to evaluate and document the safety of the Hanford Waste Vitrification Plant (HWVP). The safety of the HWVP is assessed by evaluating worst-case accident scenarios and determining the dose to offsite and onsite receptors. Air dispersion modeling is done with the GENII computer code. Three accidents are summarized in this paper, and their effects on the safety and the design of the HWVP are demonstrated

Safety design guides for seismic requirements for CANDU 9

International Nuclear Information System (INIS)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young; A. C. D. Wright

1996-03-01

This safety design guide for seismic requirements for CANDU 9 describes the seismic design philosophy, defines the applicable earthquakes and identifies the structures and systems requiring seismic qualification to ensure that the essential safety function can be adequately satisfied following earthquake. The detailed requirements for structures, systems and components which must be seismically qualified are specified in the Appendix. The change status of the regulatory requirements, code and standards should be traced and this safety design guide shall be updated accordingly. 1 fig., (Author) .new

Integrated Safety Culture Model and Application

Institute of Scientific and Technical Information of China (English)

汪磊; 孙瑞山; 刘汉辉

2009-01-01

A new safety culture model is constructed and is applied to analyze the correlations between safety culture and SMS. On the basis of previous typical definitions, models and theories of safety culture, an in-depth analysis on safety culture's structure, composing elements and their correlations was conducted. A new definition of safety culture was proposed from the perspective of sub-cuhure. 7 types of safety sub-culture, which are safety priority culture, standardizing culture, flexible culture, learning culture, teamwork culture, reporting culture and justice culture were defined later. Then integrated safety culture model (ISCM) was put forward based on the definition. The model divided safety culture into intrinsic latency level and extrinsic indication level and explained the potential relationship between safety sub-culture and all safety culture dimensions. Finally in the analyzing of safety culture and SMS, it concluded that positive safety culture is the basis of im-plementing SMS effectively and an advanced SMS will improve safety culture from all around.

Descriptions and models of safety functions - a prestudy

International Nuclear Information System (INIS)

Harms-Ringdahl, L.

1999-09-01

A study has been made with the focus on different theories and applications concerning 'safety functions' and 'barriers'. In this report, a safety function is defined as a technical or organisational function with the aim to reduce probability and/or consequences associated with a hazard. The study contains a limited review of practice and theories related to safety, with a focus on applications from nuclear and industrial safety. The study is based on a literature review and interviews. A summary has been made of definitions and terminology, which shows a large variation. E.g. 'barrier' can have a precise physical and technical meaning, or it can include human, technical and organisational elements. Only a few theoretical models describing safety functions have been found. One section of the report summarises problems related to safety issues and procedures. They concern errors in procedure design and user compliance. A proposal for describing and structuring safety functions has been made. Dimensions in a description could be degree of abstraction, systems level, the different parts of the function, etc. A model for safety functions has been proposed, which includes the division of a safety function in a number connected 'safety function elements'. One conclusion is that there is a potential for improving theories and tools for safety work and procedures. Safety function could be a useful concept in such a development, and advantages and disadvantages with this is discussed. If further work should be done, it is recommended that this is made as a combination of theoretical analysis and case studies

Integrating model checking with HiP-HOPS in model-based safety analysis

International Nuclear Information System (INIS)

Sharvia, Septavera; Papadopoulos, Yiannis

2015-01-01

The ability to perform an effective and robust safety analysis on the design of modern safety–critical systems is crucial. Model-based safety analysis (MBSA) has been introduced in recent years to support the assessment of complex system design by focusing on the system model as the central artefact, and by automating the synthesis and analysis of failure-extended models. Model checking and failure logic synthesis and analysis (FLSA) are two prominent MBSA paradigms. Extensive research has placed emphasis on the development of these techniques, but discussion on their integration remains limited. In this paper, we propose a technique in which model checking and Hierarchically Performed Hazard Origin and Propagation Studies (HiP-HOPS) – an advanced FLSA technique – can be applied synergistically with benefit for the MBSA process. The application of the technique is illustrated through an example of a brake-by-wire system. - Highlights: • We propose technique to integrate HiP-HOPS and model checking. • State machines can be systematically constructed from HiP-HOPS. • The strengths of different MBSA techniques are combined. • Demonstrated through modeling and analysis of brake-by-wire system. • Root cause analysis is automated and system dynamic behaviors analyzed and verified

Safety Design Criteria (SDC) for Gen-IV Sodium-cooled Fast Reactor

International Nuclear Information System (INIS)

Nakai, Ryodai

2013-01-01

SDC Development Background & Objectives: • Safety Design Criteria (SDC) Development for Gen-IV SFR: – Proposed at the GIF Policy Group (PG) meeting in October 2010 –SDC “harmonization” is increasingly important for: • Realization of enhanced safety designs meeting to Gen-IV safety goals and safety approach common to SFR systems; • Preparation for the forthcoming licensing in the near future; • Because Gen-IV SFR are progressing into conceptual design stage. • The SDC is the Reference criteria: – Of the designs of safety-related Structures, Systems & Components that are specific to the SFR system; – For clarifying the requisites systematically & comprehensively; – When the technology developers apply the basic safety approach and use the codes & standards for conceptual design of the Gen-IV SFR system

An aspect-oriented approach for designing safety-critical systems

Science.gov (United States)

Petrov, Z.; Zaykov, P. G.; Cardoso, J. P.; Coutinho, J. G. F.; Diniz, P. C.; Luk, W.

The development of avionics systems is typically a tedious and cumbersome process. In addition to the required functions, developers must consider various and often conflicting non-functional requirements such as safety, performance, and energy efficiency. Certainly, an integrated approach with a seamless design flow that is capable of requirements modelling and supporting refinement down to an actual implementation in a traceable way, may lead to a significant acceleration of development cycles. This paper presents an aspect-oriented approach supported by a tool chain that deals with functional and non-functional requirements in an integrated manner. It also discusses how the approach can be applied to development of safety-critical systems and provides experimental results.

Modeling issues associated with production reactor safety assessment

International Nuclear Information System (INIS)

Stack, D.W.; Thomas, W.R.

1990-01-01

This paper describes several Probabilistic Safety Assessment (PSA) modeling issues that are related to the unique design and operation of the production reactors. The identification of initiating events and determination of a set of success criteria for the production reactors is of concern because of their unique design. The modeling of accident recovery must take into account the unique operation of these reactors. Finally, a more thorough search and evaluation of common-cause events is required to account for combinations of unique design features and operation that might otherwise not be included in the PSA. It is expected that most of these modeling issues also would be encountered when modeling some of the other more unique reactor and nonreactor facilities that are part of the DOE nuclear materials production complex. 9 refs., 2 figs

Safety considerations in the design of PFBR

International Nuclear Information System (INIS)

Vaidyanathan, G.; Om Pal Singh; Govindarajan, S.; Chellapandi, P.; Chetal, S.C.; Shankar Singh, R.; Bhoje, S.B.

1996-01-01

Prototype Fast Breeder Reactor (PFBR) is a 500 MWe reactor under design in India. The overall safety approach adopted is based on the defence-in-depth principle. Design features have been incorporated to minimize occurrence of unsafe conditions. A plant protection system comprising reliable core monitoring to detect the off-normal condition, a reliable shutdown system to ensure safe shutdown and a passive decay heat removal system are provided. Containment is provided to prevent any release of radioactivity to the environment in case of failure of the protective devices. This paper provides a brief outline of the safety considerations in the design of PFBR. (author). 5 refs, 1 tab

Design of reactor containment systems for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2008-01-01

This Safety Guide was prepared under the IAEA programme for safety standards for nuclear power plants. It is a revision of the Safety Guide on Design of the Reactor Containment Systems in Nuclear Power Plants (Safety Series No. 50-Sg-D1) issued in 1985 and supplements the Safety Requirements publication on Safety of Nuclear Power Plants: Design. The present Safety Guide was prepared on the basis of a systematic review of the relevant publications, including the Safety of Nuclear Power Plants: Design, the Safety fundamentals publication on The Safety of Nuclear Installations, Safety Guides, INSAG Reports, a Technical Report and other publications covering the safety of nuclear power plants. 1.2. The confinement of radioactive material in a nuclear plant, including the control of discharges and the minimization of releases, is a fundamental safety function to be ensured in normal operational modes, for anticipated operational occurrences, in design basis accidents and, to the extent practicable, in selected beyond design basis accidents. In accordance with the concept of defence in depth, this fundamental safety function is achieved by means of several barriers and levels of defence. In most designs, the third and fourth levels of defence are achieved mainly by means of a strong structure enveloping the nuclear reactor. This structure is called the 'containment structure' or simply the 'containment'. This definition also applies to double wall containments. 1.3. The containment structure also protects the reactor against external events and provides radiation shielding in operational states and accident conditions. The containment structure and its associated systems with the functions of isolation, energy management, and control of radionuclides and combustible gases are referred to as the containment systems

Design of reactor containment systems for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

This Safety Guide was prepared under the IAEA programme for safety standards for nuclear power plants. It is a revision of the Safety Guide on Design of the Reactor Containment Systems in Nuclear Power Plants (Safety Series No. 50-Sg-D1) issued in 1985 and supplements the Safety Requirements publication on Safety of Nuclear Power Plants: Design. The present Safety Guide was prepared on the basis of a systematic review of the relevant publications, including the Safety of Nuclear Power Plants: Design, the Safety fundamentals publication on The Safety of Nuclear Installations, Safety Guides, INSAG Reports, a Technical Report and other publications covering the safety of nuclear power plants. 1.2. The confinement of radioactive material in a nuclear plant, including the control of discharges and the minimization of releases, is a fundamental safety function to be ensured in normal operational modes, for anticipated operational occurrences, in design basis accidents and, to the extent practicable, in selected beyond design basis accidents. In accordance with the concept of defence in depth, this fundamental safety function is achieved by means of several barriers and levels of defence. In most designs, the third and fourth levels of defence are achieved mainly by means of a strong structure enveloping the nuclear reactor. This structure is called the 'containment structure' or simply the 'containment'. This definition also applies to double wall containments. 1.3. The containment structure also protects the reactor against external events and provides radiation shielding in operational states and accident conditions. The containment structure and its associated systems with the functions of isolation, energy management, and control of radionuclides and combustible gases are referred to as the containment systems

Design for safety: theoretical framework of the safety aspect of BIM system to determine the safety index

Directory of Open Access Journals (Sweden)

Ai Lin Evelyn Teo

2016-12-01

Full Text Available Despite the safety improvement drive that has been implemented in the construction industry in Singapore for many years, the industry continues to report the highest number of workplace fatalities, compared to other industries. The purpose of this paper is to discuss the theoretical framework of the safety aspect of a proposed BIM System to determine a Safety Index. An online questionnaire survey was conducted to ascertain the current workplace safety and health situation in the construction industry and explore how BIM can be used to improve safety performance in the industry. A safety hazard library was developed based on the main contributors to fatal accidents in the construction industry, determined from the formal records and existing literature, and a series of discussions with representatives from the Workplace Safety and Health Institute (WSH Institute in Singapore. The results from the survey suggested that the majority of the firms have implemented the necessary policies, programmes and procedures on Workplace Safety and Health (WSH practices. However, BIM is still not widely applied or explored beyond the mandatory requirement that building plans should be submitted to the authorities for approval in BIM format. This paper presents a discussion of the safety aspect of the Intelligent Productivity and Safety System (IPASS developed in the study. IPASS is an intelligent system incorporating the buildable design concept, theory on the detection, prevention and control of hazards, and the Construction Safety Audit Scoring System (ConSASS. The system is based on the premise that safety should be considered at the design stage, and BIM can be an effective tool to facilitate the efforts to enhance safety performance. IPASS allows users to analyse and monitor key aspects of the safety performance of the project before the project starts and as the project progresses.

European Workshop Industrical Computer Science Systems approach to design for safety

Science.gov (United States)

Zalewski, Janusz

1992-01-01

This paper presents guidelines on designing systems for safety, developed by the Technical Committee 7 on Reliability and Safety of the European Workshop on Industrial Computer Systems. The focus is on complementing the traditional development process by adding the following four steps: (1) overall safety analysis; (2) analysis of the functional specifications; (3) designing for safety; (4) validation of design. Quantitative assessment of safety is possible by means of a modular questionnaire covering various aspects of the major stages of system development.

Reactor design and safety approach for a tank-type fast reactor

International Nuclear Information System (INIS)

Davies, S.M.; Yamaki, Hideo; Goodman, L.

1984-06-01

A tank type plant has been designed that offers compactness, high reliability under seismic and thermal transients, and a safety design approach that provides a balance between public safety and plant availability. This report provides a description of the design philosophy and safety features of the reactor

Opportunities for Using Building Information Modeling to Improve Worker Safety Performance

Directory of Open Access Journals (Sweden)

Kasim Alomari

2017-02-01

Full Text Available Building information modelling (BIM enables the creation of a digital representation of a designed facility combined with additional information about the project attributes, performance criteria, and construction process. Users of BIM tools point to the ability to visualize the final design along with the construction process as a beneficial feature of using BIM. Knowing the construction process in relationship to a facility’s design benefits both safety professionals when planning worker safety measures for a project and designers when creating a project’s design. Success in using BIM to enhance safety partly depends on the familiarity of project personnel with BIM tools and the extent to which the tools can be used to identify and eliminate safety hazards. In a separate, ongoing study, the authors investigated the connection between BIM and safety to document the opportunities, barriers, and impacts. Utilizing an on-line survey of project engineers who work for construction firms together with a comprehensive literature review, the study found those who use BIM feel that it aids in communication of project information and project delivery, both of which have been found to have positive impacts on construction site safety. Further, utilizing the survey results, the authors apply the binary logistic regression econometric framework to better understand the factors that lead to safety professionals believing that BIM increases safety in the work place. In addition, according to the survey results, a large percentage of the engineers who use BIM feel that ultimately it helps to eliminate safety hazards and improve worker safety. The study findings suggest that improvements in safety performance across the construction industry may be due in part to increased use of BIM in the construction industry.

Nuclear reactor conceptual design: methodology for cost-effective internalisation of nuclear safety

International Nuclear Information System (INIS)

Gimenez, M.; Grinblat, P.; Schlamp, M.

2002-01-01

A novel and promising methodology to perform nuclear reactor design is presented in this work. It achieves to balance efficiently safety and economics at the conceptual engineering stage. The key to this integral approach is to take into account safety aspects in a design optimisation process where the design variables are balanced in order to obtain a better figure of merit related with reactor economic performance. Design parameter effects on characteristic or critical safety variables, chosen from reactor behaviour during accidents and from its probabilistic safety assessment -safety performance indicators-, are synthesised on Safety Design Maps. These maps allow one to compare these indicators with limit values, which are determined by design criteria or regulations, and to transfer these restrictions to the design parameters. In this way, reactor dynamic response and other safety aspects are integrated in a global optimisation process, by means of additional rules to the neutronic, thermal-hydraulic and mechanical calculations. This methodology turns out to be promising to balance and optimise reactor and safety system design in an early engineering stage, in order to internalise cost-efficiently safety issues. It also allows one to evaluate the incremental costs of implementing higher safety levels. Furthermore, through this methodology, a simplified design can be obtained, compared to the resultant complexity when these concepts are introduced in a later engineering stage. (author)

Code on the safety of nuclear research reactors: Design

International Nuclear Information System (INIS)

1992-01-01

The main objective of this publication is to provide a safety basis for the design of a research reactor and for the assessment of the design. Another objective is to cover certain aspects related to regulatory supervision, siting and quality assurance, as far as these are related to activities for the design of a research reactor. These objectives are expressed in terms of requirements and recommendations for the design of research reactors. Emphasis is placed on the safety requirements that shall be met rather than on ways in which they can be met. The requirements and recommendations may form the foundation necessary for a Member State to develop specific regulations and safety criteria for its research reactor programme.

Safety of Nuclear Power Plants: Design. Specific Safety Requirements (Spanish Edition); Seguridad de las centrales nucleares: Diseno. Requisitos de seguridad especificos

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-04-15

This publication is a revision of Safety Requirements No. NS-R-1, Safety of Nuclear Power Plants: Design. It establishes requirements applicable to the design of nuclear power plants and elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. It will be useful for organizations involved in the design, manufacture, construction, modification, maintenance, operation and decommissioning of nuclear power plants, as well as for regulatory bodies. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Incorporation of Safety into Design Process : A Systems Engineering Perspective

NARCIS (Netherlands)

Rajabalinejad, M.

2018-01-01

This paper suggests integrating the best safety practices with the design process. This integration enriches the exploration experience for designers and adds extra values and competitor advantages for customers. The paper introduces the safety cube for combining common blocks for design, hazard

Design of concrete structures important to safety of nuclear facilities

International Nuclear Information System (INIS)

2001-10-01

Civil engineering structures in nuclear installations form an important feature having implications to safety performance of these installations. The objective and minimum requirements for the design of civil engineering buildings/structures to be fulfilled to provide adequate assurance for safety of nuclear installations in India (such as pressurised heavy water reactor and related systems) are specified in the Safety standard for civil engineering structures important to safety of nuclear facilities. This standard is written by AERB to specify guidelines for implementation of the above civil engineering safety standard in the design of concrete structures important to safety

Safety assessment in plant layout design using indexing approach: implementing inherent safety perspective. Part 1 - guideword applicability and method description.

Science.gov (United States)

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-12-15

Layout planning plays a key role in the inherent safety performance of process plants since this design feature controls the possibility of accidental chain-events and the magnitude of possible consequences. A lack of suitable methods to promote the effective implementation of inherent safety in layout design calls for the development of new techniques and methods. In the present paper, a safety assessment approach suitable for layout design in the critical early phase is proposed. The concept of inherent safety is implemented within this safety assessment; the approach is based on an integrated assessment of inherent safety guideword applicability within the constraints typically present in layout design. Application of these guidewords is evaluated along with unit hazards and control devices to quantitatively map the safety performance of different layout options. Moreover, the economic aspects related to safety and inherent safety are evaluated by the method. Specific sub-indices are developed within the integrated safety assessment system to analyze and quantify the hazard related to domino effects. The proposed approach is quick in application, auditable and shares a common framework applicable in other phases of the design lifecycle (e.g. process design). The present work is divided in two parts: Part 1 (current paper) presents the application of inherent safety guidelines in layout design and the index method for safety assessment; Part 2 (accompanying paper) describes the domino hazard sub-index and demonstrates the proposed approach with a case study, thus evidencing the introduction of inherent safety features in layout design.

Modelling blood safety

NARCIS (Netherlands)

Janssen, M.P.

2010-01-01

This thesis describes the development and application of methods and models to support decision making on safety measures aimed at preventing the transmission of infections by blood donors. Safety measures refer to screening tests for blood donors, quarantine periods for blood plasma, or methods for

Advanced Test Reactor Safety Basis Upgrade Lessons Learned Relative to Design Basis Verification and Safety Basis Management

International Nuclear Information System (INIS)

G. L. Sharp; R. T. McCracken

2004-01-01

The Advanced Test Reactor (ATR) is a pressurized light-water reactor with a design thermal power of 250 MW. The principal function of the ATR is to provide a high neutron flux for testing reactor fuels and other materials. The reactor also provides other irradiation services such as radioisotope production. The ATR and its support facilities are located at the Test Reactor Area of the Idaho National Engineering and Environmental Laboratory (INEEL). An audit conducted by the Department of Energy's Office of Independent Oversight and Performance Assurance (DOE OA) raised concerns that design conditions at the ATR were not adequately analyzed in the safety analysis and that legacy design basis management practices had the potential to further impact safe operation of the facility.1 The concerns identified by the audit team, and issues raised during additional reviews performed by ATR safety analysts, were evaluated through the unreviewed safety question process resulting in shutdown of the ATR for more than three months while these concerns were resolved. Past management of the ATR safety basis, relative to facility design basis management and change control, led to concerns that discrepancies in the safety basis may have developed. Although not required by DOE orders or regulations, not performing design basis verification in conjunction with development of the 10 CFR 830 Subpart B upgraded safety basis allowed these potential weaknesses to be carried forward. Configuration management and a clear definition of the existing facility design basis have a direct relation to developing and maintaining a high quality safety basis which properly identifies and mitigates all hazards and postulated accident conditions. These relations and the impact of past safety basis management practices have been reviewed in order to identify lessons learned from the safety basis upgrade process and appropriate actions to resolve possible concerns with respect to the current ATR safety

Safety design guides for grouping and separation for CANDU 9

International Nuclear Information System (INIS)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young; A. C. D. Wright

1996-03-01

This safety design guide for grouping and separation describes the philosophy of physical and functional separation for systems, structures and components in CANDU 9 plants and provides the requirements for the implementation of the philosophy in the detailed plant design. The separation of the safety systems is to ensure that common cause events and functional interconnections between systems do not impair the capability to perform the required safety functions for accident conditions. The separation requirements are also applied to the design by grouping the plant systems into two basic groups. Group 1 includes the power production systems and Group 2 includes the safety related systems required for the mitigation of serious process failure. The Group 2 is further separated into subgroups to ensure that events that could cause failure of a special safety system in one subgroup can be mitigated by the other subgroup. The change status for the regulatory requirements, code and standards should be traced and this safety design guide shall be updated accordingly. 2 tabs., 6 figs. (Author) .new

Safety design guides for grouping and separation for CANDU 9

Energy Technology Data Exchange (ETDEWEB)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young [Korea Atomic Energy Research Institute, Daeduk (Korea, Republic of); Wright, A C.D. [Atomic Energy of Canada Ltd., Toronto (Canada)

1996-03-01

This safety design guide for grouping and separation describes the philosophy of physical and functional separation for systems, structures and components in CANDU 9 plants and provides the requirements for the implementation of the philosophy in the detailed plant design. The separation of the safety systems is to ensure that common cause events and functional interconnections between systems do not impair the capability to perform the required safety functions for accident conditions. The separation requirements are also applied to the design by grouping the plant systems into two basic groups. Group 1 includes the power production systems and Group 2 includes the safety related systems required for the mitigation of serious process failure. The Group 2 is further separated into subgroups to ensure that events that could cause failure of a special safety system in one subgroup can be mitigated by the other subgroup. The change status for the regulatory requirements, code and standards should be traced and this safety design guide shall be updated accordingly. 2 tabs., 6 figs. (Author) .new.

Reliability Improved Design for a Safety System Channel

Energy Technology Data Exchange (ETDEWEB)

Oh, Eung Se; Kim, Yun Goo [KHNP, Daejeon (Korea, Republic of)

2016-05-15

Nowadays, these systems are implemented with a same platform type, such as a qualified programmable logic controller (PLC). The platform intensively uses digital communication with fiber-optic links to reduce cabling costs and to achieve effective signal isolation. These communication interface and redundancies within a channel increase the complexness of an overall system design. This paper proposes a simpler channel architecture design to reduce the complexity and to enhance overall channel reliability. Simplified safety channel configuration is proposed and the failure probabilities are compared with baseline safety channel configuration using an estimated generic value. The simplified channel configuration achieves 40 percent failure reduction compare to baseline safety channel configuration. If this configuration can be implemented within a processor module, overall safety channel reliability is increase and costs of fabrication and maintenance will be greatly reduced.

Reliability Improved Design for a Safety System Channel

International Nuclear Information System (INIS)

Oh, Eung Se; Kim, Yun Goo

2016-01-01

Nowadays, these systems are implemented with a same platform type, such as a qualified programmable logic controller (PLC). The platform intensively uses digital communication with fiber-optic links to reduce cabling costs and to achieve effective signal isolation. These communication interface and redundancies within a channel increase the complexness of an overall system design. This paper proposes a simpler channel architecture design to reduce the complexity and to enhance overall channel reliability. Simplified safety channel configuration is proposed and the failure probabilities are compared with baseline safety channel configuration using an estimated generic value. The simplified channel configuration achieves 40 percent failure reduction compare to baseline safety channel configuration. If this configuration can be implemented within a processor module, overall safety channel reliability is increase and costs of fabrication and maintenance will be greatly reduced

Safety principles and design management of Chashma Nuclear Power Plant

International Nuclear Information System (INIS)

Geng Qirui; Cheng Pingdong

1997-01-01

The basic safety consideration and detailed design principles in the design of Chashma Nuclear Power Plant is elaborated. The management within the frame setting up by 'safety culture' and 'quality culture'

Design of integrated passive safety system (IPSS) for ultimate passive safety of nuclear power plants

International Nuclear Information System (INIS)

Chang, Soon Heung; Kim, Sang Ho; Choi, Jae Young

2013-01-01

Highlights: • We newly propose the design concept of integrated passive safety system (IPSS). • It has five safety functions for decay heat removal and severe accident mitigation. • Simulations for IPSS show that core melt does not occur in accidents with SBO. • IPSS can achieve the passive in-vessel retention and ex-vessel cooling strategy. • The applicability of IPSS is high due to the installation outside the containment. -- Abstract: The design concept of integrated passive safety system (IPSS) which can perform various passive safety functions is proposed in this paper. It has the various functions of passive decay heat removal system, passive safety injection system, passive containment cooling system, passive in-vessel retention and cavity flooding system, and filtered venting system with containment pressure control. The objectives of this paper are to propose the conceptual design of an IPSS and to estimate the design characters of the IPSS with accident simulations using MARS code. Some functions of the IPSS are newly proposed and the other functions are reviewed with the integration of the functions. Consequently, all of the functions are modified and integrated for simplicity of the design in preparation for beyond design based accidents (BDBAs) focused on a station black out (SBO). The simulation results with the IPSS show that the decay heat can be sufficiently removed in accidents that occur with a SBO. Also, the molten core can be retained in a vessel via the passive in-vessel retention strategy of the IPSS. The actual application potential of the IPSS is high, as numerous strong design characters are evaluated. The installation of the IPSS into the original design of a nuclear power plant requires minimal design change using the current penetrations of the containment. The functions are integrated in one or two large tanks outside the containment. Furthermore, the operation time of the IPSS can be increased by refilling coolant from the

Safety considerations in the design of the fusion engineering device

International Nuclear Information System (INIS)

Barrett, R.J.

1983-01-01

Safety considerations play a significant role in the design of a near-term Fusion Engineering Device (FED). For the safety of the general public and the plant workers, the radiation environment caused by the reacting plasma and the potential release of tritium fuel are the dominant considerations. The U.S. Department of Energy (DOE) regulations and guidelines for radiation protection have been reviewed and are being applied to the device design. Direct radiation protection is provided by the device shield and the reactor building walls. Radiation from the activated device components and the tritium fuel is to be controlled with shielding, contamination control, and ventilation. The potential release of tritium from the plant has influenced the selection of reactor building and plant designs and specifications. The safety of the plant workers is affected primarily by the radiation from the activated device components and from plasma chamber debris. The highly activated device components make it necessary to design many of the maintenance activities in the reactor building for totally remote operation. The hot cell facility has evolved as a totally remote maintenance facility due to the high radiation levels of the device components. Safety considerations have had substantial impacts on the design of FED. Several examples of safety-related design impacts are discussed in the paper. Feasible solutions have been identified for all outstanding safety-related items, and additional optimization of these solutions is anticipated in future design studies

Design Information from the PSA for Digital Safety-Critical Systems

International Nuclear Information System (INIS)

Kang, Hyun Gook; Jang, Seung Cheol

2005-01-01

Many safety-critical applications such as nuclear field application usually adopt a similar design strategy for digital safety-critical systems. Their differences from the normal design for the non-safety-critical applications could be summarized as: multiple-redundancy, highly reliable components, strengthened monitoring mechanism, verified software, and automated test procedure. These items are focusing on maintaining the capability to perform the given safety function when it is requested. For the past several decades, probabilistic safety assessment (PSA) techniques are used in the nuclear industry to assess the relative effects of contributing events on plant risk and system reliability. They provide a unifying means of assessing physical faults, recovery processes, contributing effects, human actions, and other events that have a high degree of uncertainty. The applications of PSA provide not only the analysis results of already installed system but also the useful information for the system under design. The information could be derived from the PSA experience of the various safety-critical systems. Thanks to the design flexibility, the digital system is one of the most suitable candidates for risk-informed design (RID). In this article, we will describe the feedbacks for system design and try to develop a procedure for RID. Even though the procedure is not sophisticated enough now, it could be the start point of the further investigation for developing more complete and practical methodology

The Design of Cooling System Model on The AP1000 Containment

International Nuclear Information System (INIS)

Daddy Setyawan; Yerri Noer Kartiko; Aryadi Suwono; Ari Darmawan Pasek; Nathanael P Tandian; Efrizon Umar

2009-01-01

The policy of national energy leads to the utilization of new energy as nuclear energy, and also contains some efforts to increase reactor safety and optimizing in the design of safety system component such as passive cooling system on reactor containment tank. Because of this, the assessment of safety level to passive safety system needs to be made. To increase the understanding it, the design of cooling system model on containment tank should be done to get safety level on cooling system in the AP1000 containment. To reach the similar model with reality and inexpensive cost, we should make assessment about similarity and dimensionless number. While the heat transfer of air natural circulation and water spray cooling system are a result of gravity approach, we can calculate Grashof modification number and Reynolds number respectively. By this approach, we have a factor of forty for laboratory model. From this model, we hope that we get characteristic correlation to heat transfer on the containment of AP1000 for both air natural circulation and water spray result from gravity. Finally, we can assess the safety level of passive cooling system on the AP1000 containment. (author)

Safety design guides for environmental qualification for CANDU 9

International Nuclear Information System (INIS)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young; A. C. D. Wright

1996-03-01

This safety design guide describes the safety philosophy and requirements for the environmental qualification of safety related systems and components for CANDU 9. The environmental qualification program identifies the equipments to be qualified and conditions to be used for qualification and provides comprehensive set of documentation to ensure that the qualification is complete and can be maintained for the life of the plant. A summary of the system, components and structures requiring environmental qualification is provided in the table for the guidance of the system design, and this table will be subject to change or confirmation by the environmental qualification program. Also, plant ares subject to harsh environment is provided in the figure. The change status of the regulatory requirements, code and standards should be traced and this safety design guide shall be updated accordingly. 1 tab., 5 figs. (Author) .new

Safety sans Frontières: An International Safety Culture Model.

Science.gov (United States)

Reader, Tom W; Noort, Mark C; Shorrock, Steven; Kirwan, Barry

2015-05-01

The management of safety culture in international and culturally diverse organizations is a concern for many high-risk industries. Yet, research has primarily developed models of safety culture within Western countries, and there is a need to extend investigations of safety culture to global environments. We examined (i) whether safety culture can be reliably measured within a single industry operating across different cultural environments, and (ii) if there is an association between safety culture and national culture. The psychometric properties of a safety culture model developed for the air traffic management (ATM) industry were examined in 17 European countries from four culturally distinct regions of Europe (North, East, South, West). Participants were ATM operational staff (n = 5,176) and management staff (n = 1,230). Through employing multigroup confirmatory factor analysis, good psychometric properties of the model were established. This demonstrates, for the first time, that when safety culture models are tailored to a specific industry, they can operate consistently across national boundaries and occupational groups. Additionally, safety culture scores at both regional and national levels were associated with country-level data on Hofstede's five national culture dimensions (collectivism, power distance, uncertainty avoidance, masculinity, and long-term orientation). MANOVAs indicated safety culture to be most positive in Northern Europe, less so in Western and Eastern Europe, and least positive in Southern Europe. This indicates that national cultural traits may influence the development of organizational safety culture, with significant implications for safety culture theory and practice. © 2015 Society for Risk Analysis.

Safety Effect Analysis of the Large-Scale Design Changes in a Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Lee, Eun-Chan; Lee, Hyun-Gyo [Korea Hydro and Nuclear Power Co. Ltd., Daejeon (Korea, Republic of)

2015-05-15

These activities were predominantly focused on replacing obsolete systems with new systems, and these efforts were not only to prolong the plant life, but also to guarantee the safe operation of the units. This review demonstrates the safety effect evaluation using the probabilistic safety assessment (PSA) of the design changes, system improvements, and Fukushima accident action items for Kori unit 1 (K1). For the large scale of system design changes for K1, the safety effects from the PSA perspective were reviewed using the risk quantification results before and after the system improvements. This evaluation considered the seven significant design changes including the replacement of the control building air conditioning system and the performance improvement of the containment sump using a new filtering system as well as above five system design changes. The analysis results demonstrated that the CDF was reduced by 12% overall from 1.62E-5/y to 1.43E-5/y. The CDF reduction was larger in the transient group than in the loss of coolant accident (LOCA) group. In conclusion, the analysis using the K1 PSA model supports that the plant safety has been appropriately maintained after the large-scale design changes in consideration of the changed operation factors and failure modes due to the system improvements.

Review of design criteria and safety analysis of safety class electric building for fuel test loop

Energy Technology Data Exchange (ETDEWEB)

Kim, J. Y.

1998-02-01

Steady state fuel test loop will be equipped in HANARO to obtain the development and betterment of advanced fuel and materials through the irradiation tests. HANARO fuel test loop was designed for CANDU and PWR fuel testing. Safety related system of Fuel Test Loop such as emergency cooling water system, component cooling water system, safety ventilation system, high energy line break mitigation system and remote control room was required 1E class electric supply to meet the safety operation in accordance with related code. Therefore, FTL electric building was designed to construction and install the related equipment based on seismic category I. The objective of this study is to review the design criteria and analysis the safety function of safety class electric building for fuel test loop, and this results will become guidance for the irradiation testing in future. (author). 10 refs., 6 tabs., 30 figs.

The safety designs for the TITAN reversed-field pinch reactor study

International Nuclear Information System (INIS)

Wong, C.P.C.; Cheng, E.T.; Creedon, R.L.; Hoot, C.G.; Schultz, K.R.; Grotz, S.P.; Blanchard, J.; Sharafat, S.; Najmabadi, F.

1989-01-01

TITAN is a study to investigate the potential of the reversed-field pinch concept as a compact, high-power density energy system. Two reactor concepts were developed, a self-cooled lithium design with vanadium structure and an aqueous solution loop-in-pool design, both operating at 18 MW/m 2 . The key safety features of the TITAN-I lithium-vanadium blanket design are in material selection, fusion power core configuration selection, lithium piping connections, and passive lithium drain tank system. Based on these safety features and results from accident evaluation, TITAN-I can at least be rated at a level 3 of safety assurance. For the TITAN-II aqueous loop-in-pool design, the key passive feature is the complete submersion of the fusion power core and the corresponding primary coolant loop system into a pool of low temperature water. Based on this key safety design feature, the TITAN-II design can be rated at a level 2 of safety assurance. (orig.)

The safety designs for the TITAN reversed-field pinch reactor study

International Nuclear Information System (INIS)

Wong, C.P.C.; Cheng, E.T.; Creedon, R.L.; Hoot, C.G.; Schultz, K.R.; Grotz, S.P.; Blanchard, J.P.; Sharafat, S.; Najmabadi, F.

1988-01-01

TITAN is a study to investigate the potential of the reversed-field pinch concept as a compact, high-power density energy system. Two reactor concepts were developed, a self-cooled lithium design with vanadium structure and an aqueous solution loop-in-pool design, both operating at 18 MW/m 2 . The key safety features of the TITAN-I lithium-vanadium blanket design are in material selection, fusion power core configuration selection, lithium piping connections and passive lithium drain tank system. Based on these safety features and results from accident evaluation, TITAN-I can at least be rated as level 3 of safety assurance. For the TITAN-II aqueous loop-in-pool design, the key passive feature is the complete submersion of the fusion power core and the corresponding primary coolant loop system into a pool of low temperature water. Based on this key safety design feature, the TITAN-II design can be rated as level 2 of safety assurance. 7 refs., 2 figs

Safety requirements in the design of research reactors: A Canadian perspective

International Nuclear Information System (INIS)

Lee, A.G.; Langman, V.J.

2000-01-01

In Canada, the formal development of safety requirements for the design of research reactors in general began under an inter-organizational Small Reactor Criteria Committee. This committee developed safety and licensing criteria for use by several small reactor projects in their licensing discussions with the Atomic Energy Control Board. The small reactor projects or facilities represented included the MAPLE-X10 reactor, the proposed SES-10 heating reactor and its prototype, the SDR reactor at the Whiteshell Laboratories, the Korea Multipurpose Research Reactor (a.k.a., HANARO) in Korea, the SCORE project, and the McMaster University Nuclear Reactor. The top level set of criteria which form a safety philosophy and serve as a framework for more detailed developments was presented at an IAEA Conference in 1989. AECL continued this work to develop safety principles and design criteria for new small reactors. The first major application of this work has been to the design, safety analysis and licensing of the MAPLE 1 and 2 reactors for the MDS Nordion Medical Isotope Reactor Project. This paper provides an overview of the safety principles and design criteria. Examples of an implementation of these safety principles and design criteria are drawn from the work to design the MAPLE 1 and 2 reactors. (author)

Safety design study of fast breeder reactors in Japan

International Nuclear Information System (INIS)

Miura, M.; Inagaki, T.

1992-01-01

This paper reports on two fast breeder reactor (FBR) concepts, the tank type and the loop type, that have been studied as possible reactor designs to be used for a demonstration FBR (DFBR). The basic principle fo the DFBR design is to ensure plant safety through a defense-in-depth methodology. Improvements in the seismic and thermal stress designs have been attempted for both reactor concepts. The system design study strives to maximize the reliability of the safety-related systems and to rationalize commercialization of the plant

AP1000 Containment Design and Safety Assessment

International Nuclear Information System (INIS)

Wright, Richard F.; Ofstun, Richard P.; Bachere, Sebastien

2002-01-01

The AP1000 is an up-rated version of the AP600 passive plant design that recently received final design certification from the US NRC. Like AP600, the AP1000 is a two-loop, pressurized water reactor featuring passive core cooling and passive containment safety systems. One key safety feature of the AP1000 is the passive containment cooling system which maintains containment integrity in the event of a design basis accident. This system utilizes a high strength, steel containment vessel inside a concrete shield building. In the event of a pipe break inside containment, a high pressure signal actuates valves which allow water to drain from a storage tank atop the shield building. Water is applied to the top of the containment shell, and evaporates, thereby removing heat. An air flow path is formed between the shield building and the containment to aid in the evaporation and is exhausted through a chimney at the top of the shield building. Extensive testing and analysis of this system was performed as part of the AP600 design certification process. The AP1000 containment has been designed to provide increased safety margin despite the increased reactor power. The containment volume was increased to accommodate the larger steam generators, and to provide increased margin for containment pressure response to design basis events. The containment design pressure was increased from AP600 by increasing the shell thickness and by utilizing high strength steel. The passive containment cooling system water capacity has been increased and the water application rate has been scaled to the higher decay heat level. The net result is higher margins to the containment design pressure limit than were calculated for AP600 for all design basis events. (authors)

Safety design and evaluation policy for future FBRs in Japan

International Nuclear Information System (INIS)

Aizawa, Kiyoto

1991-01-01

The safety policy for fast breeder reactors (FBRs) has gradually matured in accordance with the development of FBRs. The safety assessment of the Japanese prototype FBR, Monju during the licensing process accelerated the maturity and the integration of knowledge and databases. Results are expected to be reflected in the establishment of the safety design and evaluation policy for FBRs. Although the methodologies and safety policies developed for LWRs are applicable in principle to future FBRs, it is neither rational nor realistic to treat safety only with these policies. It is recommended that one should develop the methodologies and safety policies starting from understanding of the inherent safety characteristics of FBR's through safety research, plant operating experience and design work. In the last few years, some technical committees were organized in Japan and have discussed key safety issues which are specific to FBRs in order to provide preparatory reports and to establish safety standards and guidelines for future commercial FBRs. (author)

Development of quantitative goals for inherent safety feature design and licensing

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.; Okrent, D.

1987-01-01

There is now considerable interest in the development of advanced fast reactors whose major focus is inherent safety. The achievement of inherent safety can be viewed from several aspects. In the Integral Fast Reactor Concept the approach is to utilize the intrinsic characteristics of pool-type liquid metal fast breeder reactors (LMFBRs) and the properties of metal fuels to integrate a high degree of inherent safety into the design. The PRISM and SAFR concepts focus on other inherent safety features. The reactors discussed above represent a radical departure from existing LWR designs as well as previous LMFBR designs (e.g., CRBRP) which are based, for the most part, on the General Design Criteria found in 10CFR50 Appendix. In view of these parallel developments (advanced reactors exploiting inherent safety and the use of quantitative goals to augment licensing), there appears to be a need to perform research on the development of methods for designing, assessing, and licensing inherent safety features in advanced reactors. The objectives of such research are outlined

Proposal for a technology-neutral safety approach for new reactor designs

International Nuclear Information System (INIS)

2007-09-01

Many states are considering an expansion of their nuclear power generation programmes. Many of the technologies and concepts are new and innovative. The current design and licensing rules are applicable to mostly large water reactors and there are no accepted rules in place for design, safety assessment and licensing for new innovative nuclear power plants. This TECDOC proposes a (new) safety approach and a methodology to generate technology-neutral (i.e. independent of reactor technology) safety requirements and a 'safe design' for advanced and innovative reactors. The experience gained in decades of design and licensing, combined with the development of risk-based concepts, has provided insights that will form the basis for new safety rules and requirements. Many lessons learned acknowledge the importance of such concepts as safety goals and defence in depth and the benefits of integrating risk insights early in an iterative design process. A new safety approach will incorporate many of the new developments in these concepts. For example, the probabilistic elements of defence in depth will help define the cumulative provisions to compensate for uncertainty and incompleteness of our knowledge of accident initiation and progression. This TECDOC also identifies areas of work, which will require further definition, research and development and guidance on application. This publication is to be used as a guide to developing a new technology-neutral safety approach, and as a guide in the application of methodologies to define the safety requirements for an innovative reactor designs. The method proposes an integration of deterministic and probabilistic considerations with established principles and concepts such as safety goals and defence in depth. The TECDOC recommends that the structure of the new technology-neutral main pillars for the design and licensing of innovative nuclear reactors be developed following a top-down approach to reflect a newer risk-informed and

Safety design philosophy of the ABWR for the next generation LWRs

International Nuclear Information System (INIS)

Sato, Takashi; Akinaga, Makoto; Kojima, Yoshihiro

2009-01-01

The paper presents safety design philosophy of the advanced boiling water reactor (ABWR) to be reflected in developing the next generation light water reactors (LWRs). The basic policy of the ABWR safety design was to improve safety and reduce cost simultaneously by reflecting lessons learned of precursors, incidents and accidents that were beyond the design basis such as the Three Mile Island Unit 2 (TMI 2) accident. The ABWR is a fully active safety plant. The ABWR enhanced redundancy and diversity of active safety systems using probabilistic safety assessment (PSA) insights. It adopted a complete three division active emergency core cooling system (ECCS) and attained a very low core damage frequency (CDF) value of less than 10 -7 /ry for internal events. Only very small residual risks, if any, rather exist in external events such as an extremely large earthquake beyond the design basis. This is because external events can constitute a common cause that disables all the redundant active safety systems. Therefore, it is useless to add one more ECCS train and make a four division active ECCS for external events. Nowadays, however, fully passive safety LWRs are already established. Incorporating some of these passive safety systems we can also establish the next generation LWRs that are truly strong against external events. We can establish a plant that can survive a giant earthquake at least three days without AC power source, SA proof safety design that enables no containment failure and no evacuation to eliminate the residual risks. The same basic policy as the ABWR to improve safety and reduce cost simultaneously is again effective for the next generation LWRs. (author)

Safety design analyses of Korea Advanced Liquid Metal Reactor

International Nuclear Information System (INIS)

Suk, S.D.; Park, C.K.

2000-01-01

The national long-term R and D program updated in 1997 requires Korea Atomic Energy Research Institute (KAERI) to complete by the year 2006 the basic design of Korea Advanced Liquid Metal Reactor (KALIMER), along with supporting R and D work, with the capability of resolving the issue of spent fuel storage as well as with significantly enhanced safety. KALIMER is a 150 MWe pool-type sodium cooled prototype reactor that uses metallic fuel. The conceptual design is currently under way to establish a self consistent design meeting a set of the major safety design requirements for accident prevention. Some of current emphasis include those for inherent and passive means of negative reactivity insertion and decay heat removal, high shutdown reliability, prevention of and protection from sodium chemical reaction, and high seismic margin, among others. All of these requirements affect the reactor design significantly and involve supporting R and D programs of substance. This paper summarizes some of the results of engineering and design analyses performed for the safety of KALIMER. (author)

An integrative model of organizational safety behavior.

Science.gov (United States)

Cui, Lin; Fan, Di; Fu, Gui; Zhu, Cherrie Jiuhua

2013-06-01

This study develops an integrative model of safety management based on social cognitive theory and the total safety culture triadic framework. The purpose of the model is to reveal the causal linkages between a hazardous environment, safety climate, and individual safety behaviors. Based on primary survey data from 209 front-line workers in one of the largest state-owned coal mining corporations in China, the model is tested using structural equation modeling techniques. An employee's perception of a hazardous environment is found to have a statistically significant impact on employee safety behaviors through a psychological process mediated by the perception of management commitment to safety and individual beliefs about safety. The integrative model developed here leads to a comprehensive solution that takes into consideration the environmental, organizational and employees' psychological and behavioral aspects of safety management. Copyright © 2013 National Safety Council and Elsevier Ltd. All rights reserved.

A preliminary CATHENA thermalhydraulic model of the Canadian SCWR for safety analysis

Energy Technology Data Exchange (ETDEWEB)

Wang, D.F.; Wang, S., E-mail: wangd@aecl.ca [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)

2014-06-15

The supercritical water-cooled reactor (SCWR) is one of six reactor concepts under development in the Generation-IV International Forum (GIF). As a member of GIF, Canada is developing a pressure-tube type SCWR, which has the potential to fulfill all major GIF goals on enhanced safety, sustainability, economics, and proliferation resistance. The system thermalhydraulics code CATHENA will be used in the safety analyses for the Canadian SCWR. Based on the current conceptual design of the Canadian SCWR, a CATHENA idealization has been developed. This model includes all 336 fuel channels with a detailed model of heat transfer in the reactor core. Also modeled are the main pumps, inlet plenum, outlet plenum, turbines, and heavy water moderator. In this paper, the CATHENA idealization of the Canadian SCWR conceptual design is described. Simulation results for steady-state normal operations are also presented for the current Canadian SCWR conceptual design. (author)

Design characteristics of safety parameter display system for nuclear power plants

International Nuclear Information System (INIS)

Zhang Yuangfang

1992-02-01

The design features of safety parameter display system (SPDS) developed by Tsinghua University is introduced. Some new features have been added into the system functions and they are: (1) hierarchical display structure; (2) human factor in the display format design; (3)automatic diagnosis of safety status of nuclear power plant; (4) extension of SPDS use scope; (5) flexible hardware structure. The new approaches in the design are: (1)adopting the international design standards; (2) selecting safety parameters strictly; (3) developing software under multitask operating system; (4) using a nuclear power plant simulator to verify the SPDS design

Safety of research reactors (Design and Operation)

International Nuclear Information System (INIS)

Dirar, H. M.

2012-06-01

The primary objective of this thesis is to conduct a comprehensive up-to-date literature review on the current status of safety of research reactor both in design and operation providing the future trends in safety of research reactors. Data and technical information of variety selected historical research reactors were thoroughly reviewed and evaluated, furthermore illustrations of the material of fuel, control rods, shielding, moderators and coolants used were discussed. Insight study of some historical research reactors was carried with considering sample cases such as Chicago Pile-1, F-1 reactor, Chalk River Laboratories,. The National Research Experimental Reactor and others. The current status of research reactors and their geographical distribution, reactor category and utilization is also covered. Examples of some recent advanced reactors were studied like safety barriers of HANARO of Korea including safety doors of the hall and building entrance and finger print identification which prevent the reactor from sabotage. On the basis of the results of this research, it is apparent that a high quality of safety of nuclear reactors can be attained by achieving enough robust construction, designing components of high levels of efficiency, replacing the compounds of the reactor in order to avoid corrosion and degradation with age, coupled with experienced scientists and technical staffs to operate nuclear research facilities.(Author)

Improved safety of the system 80+TM standard plants design through increased diversity and redundancy of safety systems

International Nuclear Information System (INIS)

Matzie, Regis A.; Carpentino, Frederick L.; Robertson, James E.

1996-01-01

Safely systems in the System 80+ TM Standard Plant are designed with more redundancy, diversity and simplicity than earlier nuclear power plant designs. These gains were accomplished by an evolutionary process that preserved the desirable and proven features in currently operating nuclear plants, while improving reliability and defense-in-depth. The System 80+ safety systems are the primary contributors to a core damage frequency that is more than 100 times lower than 1980's vintage U. S. designs, including the predecessor System 80 R standard nuclear steam supply system (NSSS) design. The System 80+ design includes significant improvements to the safety injection system, emergency feedwater system, shutdown cooling system, containment spray system, reactor coolant gas vent system, and to their vital support systems. These improvements enhance performance for traditional design basis events and significantly reduce the probability of a severe accident. The System 80+ design also incorporates safety systems to mitigate a severe accident. The added systems include the rapid depressurization system, the in-containment refueling water storage tank, the cavity flooding system. These systems fully address the U. S. Nuclear Regulatory Commission's (US NRC) severe accident policy. The System 80+ safety systems are integrated with the System 80+ Nuclear Island (NI) design. The NI general arrangement provides quadrant separation of the safety systems for protection from fire and flooding, and large equipment pull spaces and lay down areas for maintenance. This paper will describe the System 80+ safety systems advanced design features, the improved accident prevention and mitigation capabilities, and startup, operating and maintenance benefits

Modeling the factors affecting unsafe behavior in the construction industry from safety supervisors' perspective.

Science.gov (United States)

Khosravi, Yahya; Asilian-Mahabadi, Hassan; Hajizadeh, Ebrahim; Hassanzadeh-Rangi, Narmin; Bastani, Hamid; Khavanin, Ali; Mortazavi, Seyed Bagher

2014-01-01

There can be little doubt that the construction is the most hazardous industry in the worldwide. This study was designed to modeling the factors affecting unsafe behavior from the perspective of safety supervisors. The qualitative research was conducted to extract a conceptual model. A structural model was then developed based on a questionnaire survey (n=266) by two stage Structural Equation Model (SEM) approach. An excellent confirmed 12-factors structure explained about 62% of variances unsafe behavior in the construction industry. A good fit structural model indicated that safety climate factors were positively correlated with safety individual factors (Pconstruction workers' engagement in safe or unsafe behavior. In order to improve construction safety performance, more focus on the workplace condition is required.

Using Modeling and Rehearsal to Teach Fire Safety to Children with Autism

Science.gov (United States)

Garcia, David; Dukes, Charles; Brady, Michael P.; Scott, Jack; Wilson, Cynthia L.

2016-01-01

We evaluated the efficacy of an instructional procedure to teach young children with autism to evacuate settings and notify an adult during a fire alarm. A multiple baseline design across children showed that an intervention that included modeling, rehearsal, and praise was effective in teaching fire safety skills. Safety skills generalized to…

European passive plant program preliminary safety analyses to support system design

International Nuclear Information System (INIS)

Saiu, Gianfranco; Barucca, Luciana; King, K.J.

1999-01-01

In 1994, a group of European Utilities, together with Westinghouse and its Industrial Partner GENESI (an Italian consortium including ANSALDO and FIAT), initiated a program designated EPP (European Passive Plant) to evaluate Westinghouse Passive Nuclear Plant Technology for application in Europe. In the Phase 1 of the European Passive Plant Program which was completed in 1996, a 1000 MWe passive plant reference design (EP1000) was established which conforms to the European Utility Requirements (EUR) and is expected to meet the European Safety Authorities requirements. Phase 2 of the program was initiated in 1997 with the objective of developing the Nuclear Island design details and performing supporting analyses to start development of Safety Case Report (SCR) for submittal to European Licensing Authorities. The first part of Phase 2, 'Design Definition' phase (Phase 2A) was completed at the end of 1998, the main efforts being design definition of key systems and structures, development of the Nuclear Island layout, and performing preliminary safety analyses to support design efforts. Incorporation of the EUR has been a key design requirement for the EP1000 form the beginning of the program. Detailed design solutions to meet the EUR have been defined and the safety approach has also been developed based on the EUR guidelines. The present paper describes the EP1000 approach to safety analysis and, in particular, to the Design Extension Conditions that, according to the EUR, represent the preferred method for giving consideration to the Complex Sequences and Severe Accidents at the design stage without including them in the design bases conditions. Preliminary results of some DEC analyses and an overview of the probabilistic safety assessment (PSA) are also presented. (author)

Safety criteria for design of nuclear power plants

International Nuclear Information System (INIS)

1997-01-01

In Finland the general safety requirements for nuclear power plants are presented in the Council of State Decision (395/91). In this guide, safety principles which supplement the Council of State Decision and which are to be used in the design of nuclear power plants are defined

Safety design concept and analysis for the upgrading JRR-3

International Nuclear Information System (INIS)

Onishi, N.; Isshiki, M.; Takahashi, H.; Takayanagi, M.

1990-01-01

The Research Reactor No.3 (JRR-3) is under reconstruction for upgrading. This paper describes the safety design concepts of the architectural and engineering design, anticipated operational transients and accident conditions which are the postulated initiating events for the safety evaluation, and the safety criteria of the upgraded JRR-3. The safety criteria are defined taking into account those of Light Water Reactors and the characteristics of the research reactor. Using the example of the safety analysis, this paper describes analytical results of a reactivity insertion by removal of in-core irradiation samples, a pipeline break at the primary coolant loop and flow blockage to a coolant channel, which are the severest postulated initiating events of the JRR-3

Assessment of modelling needs for safety analysis of current HTGR concepts

International Nuclear Information System (INIS)

Kroeger, P.G.; Van Tuyle, G.J.

1985-12-01

In view of the recent shift in emphasis of the DOE/Industry HTGR development efforts to smaller modular designs it became necessary to review the modelling needs and the codes available to assess the safety performance of these new designs. This report provides a final assessment of the most urgent modelling needs, comparing these to the tools available, and outlining the most significant areas where further modelling is required. Plans to implement the required work are presented. 47 refs., 20 figs

Conceptual safety design analysis of Korea advanced liquid metal reactor

International Nuclear Information System (INIS)

Suk, S. D.; Park, C. K.

1999-01-01

The national long-term R and D program, updated in 1977, requires Korea Atomic Energy Research Institute (KAERI) to complete by the year 2006 the basic design of Korea Advanced Liquid Metal Reactor (KALIMER), along with supporting R and D work, with the capability of resolving the issue of spent fuel storage as well as with significantly enhanced safety. KALIMER is a 150 Mwe pool-type sodium cooled prototype reactor that uses metallic fuel. The conceptual design is currently under way to establish a self-consistent design meeting a set of major safety design requirements for accident prevention. Some of the current emphasis includes those for inherent and passive means of negative reactivity insertion and decay heat removal, high shutdown reliability, prevention of and protection from sodium chemical reaction, and high seismic margin, among others. All of these requirements affect the reactor design significantly and involve extensive supporting R and D programs. This paper summarizes some of the results of conceptual engineering and design analyses performed for the safety of KALIMER in the area of inherent safety, passive decay heat removal, sodium water reaction, and seismic isolation. (author)

Job Demands-Control-Support model and employee safety performance.

Science.gov (United States)

Turner, Nick; Stride, Chris B; Carter, Angela J; McCaughey, Deirdre; Carroll, Anthony E

2012-03-01

The aim of this study was to explore whether work characteristics (job demands, job control, social support) comprising Karasek and Theorell's (1990) Job Demands-Control-Support framework predict employee safety performance (safety compliance and safety participation; Neal and Griffin, 2006). We used cross-sectional data of self-reported work characteristics and employee safety performance from 280 healthcare staff (doctors, nurses, and administrative staff) from Emergency Departments of seven hospitals in the United Kingdom. We analyzed these data using a structural equation model that simultaneously regressed safety compliance and safety participation on the main effects of each of the aforementioned work characteristics, their two-way interactions, and the three-way interaction among them, while controlling for demographic, occupational, and organizational characteristics. Social support was positively related to safety compliance, and both job control and the two-way interaction between job control and social support were positively related to safety participation. How work design is related to employee safety performance remains an important area for research and provides insight into how organizations can improve workplace safety. The current findings emphasize the importance of the co-worker in promoting both safety compliance and safety participation. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

Safety principles and design criteria for nuclear power stations

International Nuclear Information System (INIS)

Gazit, M.

1982-01-01

The criteria and safety principles for the design of nuclear power stations are presented from the viewpoint of a nuclear engineer. The design, construction and operation of nuclear power stations should be carried out according to these criteria and safety principles to ensure, to a reasonable degree, that the likelihood of release of radioactivity as a result of component failure or human error should be minimized. (author)

Safety Design Criteria of Indian Sodium Cooled Fast Reactors

International Nuclear Information System (INIS)

Pillai, P.; Chellapandi, P.; Chetal, S.C.; Vasudeva Rao, P.R.

2013-01-01

• Important feedback has been gained through the design and safety review of PFBR. • The safety criteria document prepared by AERB and IGCAR would provide important input to prepare the dedicated document for the Sodium cooled Fast Reactors at the national and international level. • A common approach with regard to safety, among countries pursuing fast reactor program, is desirable. • Sharing knowledge and experimental facilities on collaborative basis. • Evolution of strong safety criteria – fundamental to assure safety

Meeting Human Reliability Requirements through Human Factors Design, Testing, and Modeling

Energy Technology Data Exchange (ETDEWEB)

R. L. Boring

2007-06-01

In the design of novel systems, it is important for the human factors engineer to work in parallel with the human reliability analyst to arrive at the safest achievable design that meets design team safety goals and certification or regulatory requirements. This paper introduces the System Development Safety Triptych, a checklist of considerations for the interplay of human factors and human reliability through design, testing, and modeling in product development. This paper also explores three phases of safe system development, corresponding to the conception, design, and implementation of a system.

Architecture Level Safety Analyses for Safety-Critical Systems

Directory of Open Access Journals (Sweden)

K. S. Kushal

2017-01-01

Full Text Available The dependency of complex embedded Safety-Critical Systems across Avionics and Aerospace domains on their underlying software and hardware components has gradually increased with progression in time. Such application domain systems are developed based on a complex integrated architecture, which is modular in nature. Engineering practices assured with system safety standards to manage the failure, faulty, and unsafe operational conditions are very much necessary. System safety analyses involve the analysis of complex software architecture of the system, a major aspect in leading to fatal consequences in the behaviour of Safety-Critical Systems, and provide high reliability and dependability factors during their development. In this paper, we propose an architecture fault modeling and the safety analyses approach that will aid in identifying and eliminating the design flaws. The formal foundations of SAE Architecture Analysis & Design Language (AADL augmented with the Error Model Annex (EMV are discussed. The fault propagation, failure behaviour, and the composite behaviour of the design flaws/failures are considered for architecture safety analysis. The illustration of the proposed approach is validated by implementing the Speed Control Unit of Power-Boat Autopilot (PBA system. The Error Model Annex (EMV is guided with the pattern of consideration and inclusion of probable failure scenarios and propagation of fault conditions in the Speed Control Unit of Power-Boat Autopilot (PBA. This helps in validating the system architecture with the detection of the error event in the model and its impact in the operational environment. This also provides an insight of the certification impact that these exceptional conditions pose at various criticality levels and design assurance levels and its implications in verifying and validating the designs.

Radiation protection aspects of design for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2005-01-01

The IAEA's Statute authorizes the Agency to establish safety standards to protect health and minimize danger to life and property - standards which the IAEA must use in its own operations, and which a State can apply by means of its regulatory provisions for nuclear and radiation safety. A comprehensive body of safety standards under regular review, together with the IAEA's assistance in their application, has become a key element in a global safety regime. In the mid-1990s, a major overhaul of the IAEA's safety standards programme was initiated, with a revised oversight committee structure and a systematic approach to updating the entire corpus of standards. The new standards that have resulted are of a high calibre and reflect best practices in Member States. With the assistance of the Commission on Safety Standards, the IAEA is working to promote the global acceptance and use of its safety standards. Safety standards are only effective, however, if they are properly applied in practice. The IAEA's safety services - which range in scope from engineering safety, operational safety, and radiation, transport and waste safety to regulatory matters and safety culture in organizations - assist Member States in applying the standards and appraise their effectiveness. These safety services enable valuable insights to be shared and continue to urge all Member States to make use of them. Regulating nuclear and radiation safety is a national responsibility, and many Member States have decided to adopt the IAEA's safety standards for use in their national regulations. For the Contracting Parties to the various international safety conventions, IAEA standards provide a consistent, reliable means of ensuring the effective fulfilment of obligations under the conventions. The standards are also applied by designers, manufacturers and operators around the world to enhance nuclear and radiation safety in power generation, medicine, industry, agriculture, research and education

Design of marine structures with improved safety for environment

International Nuclear Information System (INIS)

Klanac, Alan; Varsta, Petri

2011-01-01

The paper describes a method for design of marine structures with increased safety for environment, considering also the required investment costs as well as the aspects of risk distribution onto the maritime stakeholders. Practically, the paper seeks to answer what is the optimal amount that should be invested into certain safety measure for any given vessel. Due to the uneven distribution of risk, as well as the differing impact of costs emerging from safety improvements, stakeholders experience conflicting ranking of alternatives. To solve this multi-stakeholder decision-making problem, in which each stakeholder is a decision-maker, the method applies concepts of group decision-making theory, namely the Game Theory. The method fosters axiomatic definition of the optimum solution, arguing that the solution, or the final selected design, should satisfy the non-dominance, efficiency, and fairness. These three are thoroughly discussed in terms of structural design, especially the latter. Considering the coupling of environmental risk and structural design, the method also builds on the preference structure of four maritime stakeholders: yards, owners, oil receivers and the public, who either share the risks or directly influence structural design. Method is presented on a practical study of structural design of a tanker with a crashworthy side structure that is capable of reducing the risk of collision. The outcome of this study outlines a number of possibilities for successful improvement of tanker safety that can benefit, concurrently, all maritime stakeholders.

Model-Driven Development of Safety Architectures

Science.gov (United States)

Denney, Ewen; Pai, Ganesh; Whiteside, Iain

2017-01-01

We describe the use of model-driven development for safety assurance of a pioneering NASA flight operation involving a fleet of small unmanned aircraft systems (sUAS) flying beyond visual line of sight. The central idea is to develop a safety architecture that provides the basis for risk assessment and visualization within a safety case, the formal justification of acceptable safety required by the aviation regulatory authority. A safety architecture is composed from a collection of bow tie diagrams (BTDs), a practical approach to manage safety risk by linking the identified hazards to the appropriate mitigation measures. The safety justification for a given unmanned aircraft system (UAS) operation can have many related BTDs. In practice, however, each BTD is independently developed, which poses challenges with respect to incremental development, maintaining consistency across different safety artifacts when changes occur, and in extracting and presenting stakeholder specific information relevant for decision making. We show how a safety architecture reconciles the various BTDs of a system, and, collectively, provide an overarching picture of system safety, by considering them as views of a unified model. We also show how it enables model-driven development of BTDs, replete with validations, transformations, and a range of views. Our approach, which we have implemented in our toolset, AdvoCATE, is illustrated with a running example drawn from a real UAS safety case. The models and some of the innovations described here were instrumental in successfully obtaining regulatory flight approval.

The design and safety features of the IRIS reactor

International Nuclear Information System (INIS)

Carelli, Mario D.; Conway, L.E.; Oriani, L.; Petrovic, B.; Lombardi, C.V.; Ricotti, M.E.; Barroso, A.C.O.; Collado, J.M.; Cinotti, L.; Todreas, N.E.; Grgic, D.; Moraes, M.M.; Boroughs, R.D.; Ninokata, H.; Ingersoll, D.T.; Oriolo, F.

2004-01-01

Salient features of the International Reactor Innovative and Secure (IRIS) are presented here. IRIS, an integral, modular, medium size (335 MWe) PWR, has been under development since the turn of the century by an international consortium led by Westinghouse and including over 20 organizations from nine countries. Described here are the features of the integral design which includes steam generators, pumps and pressurizer inside the vessel, together with the core, control rods, and neutron reflector/shield. A brief summary is provided of the IRIS approach to extended maintenance over a 48-month schedule. The unique IRIS safety-by-design approach is discussed, which, by eliminating accidents, at the design stage, or decreasing their consequences/probabilities when outright elimination is not possible, provides a very powerful first level of defense in depth. The safety-by-design allows a significant reduction and simplification of the passive safety systems, which are presented here, together with an assessment of the IRIS response to transients and postulated accidents

Safety design approach for JSFR toward the realization of GEN IV SFR

International Nuclear Information System (INIS)

Kubo, S.; Yamano, H.; Chikazawa, Y.; Shimakawa, Y.

2013-01-01

Conclusion: Safety Design Approach for JSFR: • Based on the safety design criteria for Generation-IV SFR • DECs, Situations practically eliminated and related design measures are identified and selected with due consideration of the safety features of SFR and the lessons learned from the TEPCO’s Fukushima Dai-ichi nuclear power plants accident Safety Design Concept of JSFR: • For failure to shutdown: Passive shutdown capability, Mitigation of core damage (Prevention of severe mechanical energy release, In-Vessel Retention) • For failure to remove heat: Prevention of significant core damage (Natural circulation DHR, Alternative cooling measures) • Containment: Prevention of sever dynamic loads by design measures (IVR, double boundary concept, inertization)

A new design concept for offshore nuclear power plants with enhanced safety features

International Nuclear Information System (INIS)

Lee, Kihwan; Lee, Kang-Heon; Lee, Jeong Ik; Jeong, Yong Hoon; Lee, Phill-Seung

2013-01-01

Highlights: ► A new design concept for offshore nuclear power plants is proposed. ► The total general arrangement for the concept is suggested. ► A new emergency passive containment cooling system (EPCCS) is proposed. ► A new emergency passive reactor-vessel cooling system (EPRVCS) is proposed. ► Safety features against earthquakes, tsunamis, and storms are discussed. - Abstract: In this paper, we present a new concept for offshore nuclear power plants (ONPP) with enhanced safety features. The design concept of a nuclear power plant (NPP) mounted on gravity-based structures (GBSs), which are widely used offshore structures, is proposed first. To demonstrate the feasibility of the concept, a large-scale land-based nuclear power plant model APR1400, which is the most recent NPP model in the Republic of Korea, is mounted on a GBS while minimizing modification to the original features of APR1400. A new total general arrangement (GA) and basic design principles are proposed and can be directly applied to any existing land based large scale NPPs. The proposed concept will enhance the safety of a NPP due to several aspects. A new emergency passive containment cooling system (EPCCS) and emergency passive reactor-vessel cooling system (EPRVCS) are proposed; their features of using seawater as coolant and safety features against earthquakes, Tsunamis, storms, and marine collisions are also described. We believe that the proposed offshore nuclear power plant is more robust than conventional land-based nuclear power plants and it has strong potential to provide great opportunities in nuclear power industries by decoupling the site of construction and that of installation.

Safe-by-Design : from Safety to Responsibility

NARCIS (Netherlands)

van de Poel, I.R.; Robaey, Z.H.

2017-01-01

Safe-by-design (SbD) aims at addressing safety issues already during the R&D and design phases of new technologies. SbD has increasingly become popular in the last few years for addressing the risks of emerging technologies like nanotechnology and synthetic biology. We ask to what extent SbD

A Technique of Software Safety Analysis in the Design Phase for PLC Based Safety-Critical Systems

International Nuclear Information System (INIS)

Koo, Seo-Ryong; Kim, Chang-Hwoi

2017-01-01

The purpose of safety analysis, which is a method of identifying portions of a system that have the potential for unacceptable hazards, is firstly to encourage design changes that will reduce or eliminate hazards and, secondly, to conduct special analyses and tests that can provide increased confidence in especially vulnerable portions of the system. For the design and implementation phase of the PLC based systems, we proposed a technique for software design specification and analysis, and this technique enables us to generate software design specifications (SDSs) in nuclear fields. For the safety analysis in the design phase, we used architecture design blocks of NuFDS to represent the architecture of the software. On the basis of the architecture design specification, we can directly generate the fault tree and then use the fault tree for qualitative analysis. Therefore, we proposed a technique of fault tree synthesis, along with a universal fault tree template for the architecture modules of nuclear software. Through our proposed fault tree synthesis in this work, users can use the architecture specification of the NuFDS approach to intuitively compose fault trees that help analyze the safety design features of software.

The basic discussion on nuclear power safety improvement based on nuclear equipment design

International Nuclear Information System (INIS)

Zhao Feiyun; Yao Yangui; Yu Hao; He Yinbiao; Gao Lei; Yao Weida

2013-01-01

The safety of strengthening nuclear power design was described based on nuclear equipment design after Fukushima nuclear accident. From these aspects, such as advanced standard system, advanced design method, suitable test means, consideration of beyond design basis event, and nuclear safety culture construction, the importance of nuclear safety improvement was emphatically presented. The enlightenment was given to nuclear power designer. (authors)

Safety considerations in next step fusion design and beyond

International Nuclear Information System (INIS)

Holland, D.F.

1990-01-01

Recent U.S. and international design studies provide insights into the potential safety and environmental advantages of fusion as well as the development needed to realize this potential. We in the Fusion Safety Program at EG ampersand G Idaho have analyzed the Compact Ignition Tokamak (CIT), the International Thermonuclear Engineering Reactor (ITER), and the Advanced Reactor Innovative Engineering Study (ARIES). I have reviewed these three designs to determine issues related to meeting the safety and the environmental goals that guide fusion development in the U.S. The paper lists safety and environmental issues that are generic to fusion and approaches to favorably resolve each issue. The technical developments that have the highest potential of contributing to improving the safety and environmental attractiveness of fusion are identified and discussed. These developments are in the areas of low-activation materials, plasma- facing components, and plasma physics relating to off-normal plasma events and tritium burn-up. 8 refs., 7 tabs

Small nuclear reactor safety design requirements for autonomous operation

International Nuclear Information System (INIS)

Kozier, K.S.; Kupca, S.

1997-01-01

Small nuclear power reactors offer compelling safety advantages in terms of the limited consequences that can arise from major accident events and the enhanced ability to use reliable, passive means to eliminate their occurrence by design. Accordingly, for some small reactor designs featuring a high degree of safety autonomy, it may be-possible to delineate a ''safety envelope'' for a given set of reactor circumstances within which safe reactor operation can be guaranteed without outside intervention for time periods of practical significance (i.e., days or weeks). The capability to operate a small reactor without the need for highly skilled technical staff permanently present, but with continuous remote monitoring, would aid the economic case for small reactors, simplify their use in remote regions and enhance safety by limiting the potential for accidents initiated by inappropriate operator action. This paper considers some of the technical design options and issues associated with the use of small power reactors in an autonomous mode for limited periods. The focus is on systems that are suitable for a variety of applications, producing steam for electricity generation, district heating, water desalination and/or marine propulsion. Near-term prospects at low power levels favour the use of pressurized, light-water-cooled reactor designs, among which those having an integral core arrangement appear to offer cost and passive-safety advantages. Small integral pressurized water reactors have been studied in many countries, including the test operation of prototype systems. (author)

Video Modeling to Teach Social Safety Skills to Young Adults with Intellectual Disability

Science.gov (United States)

Spivey, Corrine E.; Mechling, Linda C.

2016-01-01

This study evaluated the effectiveness of video modeling with a constant time delay procedure to teach social safety skills to three young women with intellectual disability. A multiple probe design across three social safety skills (responding to strangers who: requested personal information; requested money; and entered the participant's…

A cost-effective methodology to internalize nuclear safety in nuclear reactor conceptual design

International Nuclear Information System (INIS)

Gimenez, M.; Grinblat, P.; Schlamp, M.

2003-01-01

A new methodology to perform nuclear reactor design, balancing safety and economics at the conceptual engineering stage, is presented in this work. The goal of this integral methodology is to take into account safety aspects in an optimization design process where the design variables are balanced in order to obtain a better figure of merit related with reactor economic performance. Design parameter effects on characteristic or critical safety variables, chosen from reactor behavior during accidents (safety performance indicators), are synthesized on Design Maps. These maps allow one to compare the safety indicator with limits, which are determined by design criteria or regulations, and to transfer these restrictions to the design parameters. In this way, reactor dynamic response and other safety aspects are integrated in a global optimization process, by means of additional rules to the neutronic, thermal-hydraulic, and mechanical calculations. An application of the methodology, implemented in Integrated Reactor Evaluation Program 3 (IREP3) code, to optimize safety systems of CAREM prototype is presented. It consists in balancing the designs of the Emergency Injection System (EIS), the Residual Heat Removal System (RHRS), the primary circuit water inventory and the containment height, to cope with loss of coolant and loss of heat sink (LOHS) accidental sequences, taking into account cost and reactor performance. This methodology turns out to be promising to internalize cost-efficiently safety issues. It also allows one to evaluate the incremental costs of implementing higher safety levels

Conceptual design of safety instrumentation for PFBR

International Nuclear Information System (INIS)

Muralikrishna, G.; Seshadri, U.; Raghavan, K.

1996-01-01

Instrumentation systems enable monitoring of the process which in turn enables control and shutdown of the process as per the requirements. Safety Instrumentation due to its vital importance has a stringent role and this needs to be designed methodically. This paper presents the details of the conceptual design for PFBR. (author). 4 figs, 3 tabs

DART - for design basis justification and safety related information management

International Nuclear Information System (INIS)

Billington, A.; Blondiaux, P.; Boucau, J.; Cantineau, B.; Doumont, C.; Mared, A.

2000-01-01

DART is the acronym for Design Analysis Re-engineering Tool. It embodies a systematic and integrated approach to NPP safety re-assessment and configuration management, that makes use of Reverse Failure Mode and Effect Analysis in conjunction with a state-of-the-art relational database and a standardized data format, to permit long-term management of plant safety related information. The plant design is reviewed in a step-by-step logical fashion by constructing fault trees that identify the link between undesired consequences and their causes. Each failure cause identified in a fault tree is addressed by defining functional requirements, which are in turn addressed by documenting the specific manner in which the plant complies with the requirement. The database can be used to generate up-to-date plant safety related documents, including: SAR, Systems Descriptions, Technical Specifications and plant procedures. The approach is open-minded by nature and therefore is not regulatory driven, however the plant licensing basis will also be reviewed and documented within the same database such that a Regulatory Conformance Program may be integrated with the other safety documentation. This methodology can thus reconstitute the plant design bases in a comprehensive and systematic way, while allowing to uncover weaknesses in design. The original feature of the DART methodology is that it links all the safety related documents together, facilitating the evaluation of the safety impact resulting from any plant modification. Due to its capability to retrieve the basic justifications of the plant design, it is also a useful tool for training the young generation of plant personnel. The DART methodology has been developed for application to units 2, 3 and 4 at Vattenfall's Ringhals site in Sweden. It may be applied to any nuclear power plant or industrial facility where public safety is a concern. (author)

DART - for design basis justification and safety related information management

International Nuclear Information System (INIS)

Billington, A.; Blondiaux, B.; Boucau, J.; Cantineau, B.; Mared, A.

2001-01-01

DART is the acronym for Design Analysis Re-Engineering Tool. It embodies a systematic and integrated approach to NPP safety re-assessment and configuration management, that makes use of Reverse Failure Mode and Effect Analysis in conjunction with a state-of-the-art relational database and a standardized data format, to permit long-term management of plant safety related information. The plant design is reviewed in a step-by-step logical fashion by constructing fault trees that identify the link between undesired consequences and their causes. Each failure cause identified in a fault tree is addressed by defining functional requirements, which are in turn addressed by documenting the specific manner in which the plant complies with the requirement. The database can then be used to generate up-to-date plant safety related documents, including: SAR, Systems Descriptions, Technical Specifications and plant procedures. The approach is open-minded by nature and therefore is not regulatory driven, however the plant licensing basis will also be reviewed and documented within the same database such that a Regulatory Conformance Program may be integrated with the other safety documentation. This methodology can thus reconstitute the plant design bases in a comprehensive and systematic way, while allowing to uncover weaknesses in design. The original feature of the DART methodology is that it links all the safety related documents together, facilitating the evaluation of the safety impact resulting from any plant modification. Due to its capability to retrieve the basic justifications of the plant design, it is also a useful tool for training the young generation of plant personnel. The DART methodology has been developed for application to units 2, 3 and 4 at Vattenfall's Ringhals site in Sweden. It may be applied to any nuclear power plant or industrial facility where public safety is a concern. (author)

An Innovative Hybrid Loop-Pool SFR Design and Safety Analysis Methods: Today and Tomorrow

International Nuclear Information System (INIS)

Hongbin Zhang; Haihua Zhao; Vincent Mousseau

2008-01-01

Investment in commercial sodium cooled fast reactor (SFR) power plants will become possible only if SFRs achieve economic competitiveness as compared to light water reactors and other Generation IV reactors. Toward that end, we have launched efforts to improve the economics and safety of SFRs from the thermal design and safety analyses perspectives at Idaho National Laboratory. From the thermal design perspective, an innovative hybrid loop-pool SFR design has been proposed. This design takes advantage of the inherent safety of a pool design and the compactness of a loop design to further improve economics and safety. From the safety analyses perspective, we have initiated an effort to develop a high fidelity reactor system safety code

Passive safety design characteristics of the KALIMER-600 burner reactor

International Nuclear Information System (INIS)

Kwon, Young-Min; Jeong, Hae-Yong; Cho, Chung-Ho; Ha, Ki-Seok; Kim, Sang-Ji

2009-01-01

The Korea Atomic Energy Research Institute (KAERI) has recently studied several burner core designs for a transuranics (TRU) transmutation based on the breakeven core geometry of KALIMER-600. The KALIMER-600 is a net electrical rating of 600MWe, sodium-cooled, metallic-fueled, pool-type reactor. For the burner core concept selected for the present analysis, the smearing fractions of the fuel rods in three fuel zones are changed while maintaining the cladding outer diameter and cladding thickness. The resulting fuel slug smearing fractions of the inner, middle, and outer core zones are 36%, 40%, and 48%, respectively. The TRU conversion ratio is 0.57 and the TRU enrichment of the driver fuel is set to 30.0 w/o because of the current practical limitation of the U-TRU-10%Zr metal fuel database. The purpose of this paper is to evaluate the safety performance characteristics provided by the passive safety design features in the KALIMER-600 burner reactor by using a system-wide safety analysis code. The present scoping analysis focuses on an assessment of the enhanced safety design features that provide passive and self-regulating responses to transient conditions and an evaluation of the safety margin during unprotected overpower, unprotected loss of flow, and unprotected loss of heat sink events. The analysis results show that the KALIMER-600 burner reactor provides larger safety margins with respect to the sodium boiling, fuel rod integrity, and structural integrity. The overall inherent safety can be enhanced by accounting for the reactivity feedback mechanisms in the design process. (author)

Designing a Safety Reporting Smartphone Application to Improve Patient Safety After Total Hip Arthroplasty.

Science.gov (United States)

Krumsvik, Ole Andreas; Babic, Ankica

2017-01-01

This paper presents a safety reporting smartphone application which is expected to reduce the occurrence of postoperative adverse events after total hip arthroplasty (THA). A user-centered design approach was utilized to facilitate optimal user experience. Two main implemented functionalities capture patient pain levels and well-being, the two dimensions of patient status that are intuitive and commonly checked. For these and other functionalities, mobile technology could enable timely safety reporting and collection of patient data out of a hospital setting. The HCI expert, and healthcare professionals from the Haukeland University Hospital in Bergen have assessed the design with respect to the interaction flow, information content, and self-reporting functionalities. They have found it to be practical, intuitive, sufficient and simple for users. Patient self-reporting could help recognizing safety issues and adverse events.

The spread model of food safety risk under the supply-demand disturbance.

Science.gov (United States)

Wang, Jining; Chen, Tingqiang

2016-01-01

In this paper, based on the imbalance of the supply-demand relationship of food, we design a spreading model of food safety risk, which is about from food producers to consumers in the food supply chain. We use theoretical analysis and numerical simulation to describe the supply-demand relationship and government supervision behaviors' influence on the risk spread of food safety and the behaviors of the food producers and the food retailers. We also analyze the influence of the awareness of consumer rights protection and the level of legal protection of consumer rights on the risk spread of food safety. This model contributes to the explicit investigation of the influence relationship among supply-demand factors, the regulation behavioral choice of government, the behavioral choice of food supply chain members and food safety risk spread. And this paper provides a new viewpoint for considering food safety risk spread in the food supply chain, which has a great reference for food safety management.

The safety relief valve handbook design and use of process safety valves to ASME and International codes and standards

CERN Document Server

Hellemans, Marc

2009-01-01

The Safety Valve Handbook is a professional reference for design, process, instrumentation, plant and maintenance engineers who work with fluid flow and transportation systems in the process industries, which covers the chemical, oil and gas, water, paper and pulp, food and bio products and energy sectors. It meets the need of engineers who have responsibilities for specifying, installing, inspecting or maintaining safety valves and flow control systems. It will also be an important reference for process safety and loss prevention engineers, environmental engineers, and plant and process designers who need to understand the operation of safety valves in a wider equipment or plant design context. . No other publication is dedicated to safety valves or to the extensive codes and standards that govern their installation and use. A single source means users save time in searching for specific information about safety valves. . The Safety Valve Handbook contains all of the vital technical and standards informat...

Design for safety: A cognitive engineering approach to the control and management of nuclear power plants

International Nuclear Information System (INIS)

Boy, Guy A.; Schmitt, Kara A.

2013-01-01

Highlights: ► Complexity must be understood and handled well in order to design for safety. ► Complexity can be reduced during design by using the AUTOS pyramid model. ► Procedures are human automation, much as software is machine automation. ► Identifying emergent behaviors reduces procedure accumulation. ► Human-in-the-loop-simulations help to understand emergent behaviors. -- Abstract: This paper presents an analytical approach to design for safety that is based on 30 years of experience in the field of Human-centered design. This field is often qualified as governing safety–critical systems where risk management is a crucial issue. We need to better understand what the main facets of safety are that should be taken into account during the design and development processes. There are many factors that contribute to design for safety. We propose some of these factors and an articulation of them from requirement gathering and synthesis to formative evaluations to summative evaluations. Among these factors, we analyze complexity, flexibility, stability, redundancy, support, training, experience and testing. However, we cannot design a safe and reliable product in one shot; design is incremental. A product and its various uses become progressively mature. When we deal with new products, issues come from the fact that practice features emerge from the use of the product and are difficult, even impossible, to predict ahead of time. The automation within is an important portion of this maturity, and must be understood well. This is why design for safety is not possible without anticipatory simulations and a period of tests in the real world, such as operational testing in nuclear power plants. In addition, designing for safety is not finished when the product is delivered; experience feedback, or human-in-the-loop simulation (HITLS) is an important part of the overall global design process. The AUTOS pyramid approach can assist in simplifying the

Using network screening methods to determine locations with specific safety issues: A design consistency case study.

Science.gov (United States)

Butsick, Andrew J; Wood, Jonathan S; Jovanis, Paul P

2017-09-01

The Highway Safety Manual provides multiple methods that can be used to identify sites with promise (SWiPs) for safety improvement. However, most of these methods cannot be used to identify sites with specific problems. Furthermore, given that infrastructure funding is often specified for use related to specific problems/programs, a method for identifying SWiPs related to those programs would be very useful. This research establishes a method for Identifying SWiPs with specific issues. This is accomplished using two safety performance functions (SPFs). This method is applied to identifying SWiPs with geometric design consistency issues. Mixed effects negative binomial regression was used to develop two SPFs using 5 years of crash data and over 8754km of two-lane rural roadway. The first SPF contained typical roadway elements while the second contained additional geometric design consistency parameters. After empirical Bayes adjustments, sites with promise (SWiPs) were identified. The disparity between SWiPs identified by the two SPFs was evident; 40 unique sites were identified by each model out of the top 220 segments. By comparing sites across the two models, candidate road segments can be identified where a lack design consistency may be contributing to an increase in expected crashes. Practitioners can use this method to more effectively identify roadway segments suffering from reduced safety performance due to geometric design inconsistency, with detailed engineering studies of identified sites required to confirm the initial assessment. Copyright © 2017 Elsevier Ltd. All rights reserved.

ARIES-RS safety design and analysis

International Nuclear Information System (INIS)

Steiner, D.; El-Guebaly, L.; Herring, S.; Khater, H.; Mogahed, E.; Thayer, R.; Tillack, M.S.

1997-01-01

The ARIES-RS safety design and analysis focused on achieving two objectives: (1) The avoidance of sheltering or evacuation in the event of an accident; and (2) the generation of only low-level waste, no greater than Class C. The ARIES-RS baseline design employs V-4Cr-4Ti as the blanket structural material and a low activation ferritic steel in the reflector and shield. In the event of a LOCA, the baseline design first wall maximum temperature falls in the range of 1100-1200 C. For this temperature range, the hazard assessment indicates that the dose at the site boundary will be less than 1 rem per year. Thus, no sheltering or evacuation would be required in the event of a LOCA. Although the baseline design satisfies the first safety objective noted above, a first wall maximum temperature of ∝1100-1200 C would likely compromise the integrity of the vanadium blanket structure and would require blanket replacement following such a temperature excursion. To avoid this situation, a modified blanket design incorporating supplemental heat removal is also proposed. Preliminary analysis of this modified design suggests that the first wall maximum temperature can be kept below the temperature range of concern, ∝1000-1100 C, in the event of a LOCA. When the ferritic steel used in the reflector and shield is one reduced in Ir and Ag impurities, all in-vessel components qualify for near-surface shallow land burial as Class C low-level waste. (orig.)

Design concepts and safety concerns of the small and medium size reactors (SMR)

International Nuclear Information System (INIS)

Seul, Kwang Won; Lee, Jae Hun; Kim, Hho Jung

1998-01-01

The small and medium size reactors (SMR) and interface facilities such as desalination plant are expected to be located near the population area because of restrictions in transporting the plant products such as fresh water to long distance area. To protect the public around the plant facility from the possible release of radioactive materials, the design development of the SMR is focusing on an enhancement of the safety and reliability as well as the economics. In this study, the major safety concepts of the SMR designs significantly different from the current PWR designs are investigated and the safety concerns applicable to the integrated SMR design of Korea (called SMART), were identified. Those safety issues include the use of proven technology, application of strengthening defense in depth, event categorization and selection, simplification of emergency planning, determination of accident source terms and so on. The efforts to resolve the safety concerns in the design stage will provide an improvement of the safety of the SMART design

Safety parameter display system (SPDS) for Russian-designed NPPs

International Nuclear Information System (INIS)

Anikanov, S.S.; Catullo, W.J.; Pelusi, J.L.

1997-01-01

As part of the programs aimed at improving the safety of Russian-designed reactors, the US DoE has sponsored a project of providing a safety parameter display system (SPDS) for nuclear power plants with such reactors. The present paper is focused mostly on the system architecture design features of SPDS systems for WWER-1000 and RBMK-1000 reactors. The function and the operating modes of the SPDS are outlined, and a description of the display system is given. The system architecture and system design of both an integrated and a stand-alone IandC system is explained. (A.K.)

Technical Review Report for the Model 9975-96 Package Safety Analysis Report for Packaging (S-SARP-G-00003, Revision 0, January 2008)

International Nuclear Information System (INIS)

West, M.

2009-01-01

This Technical Review Report (TRR) documents the review, performed by the Lawrence Livermore National Laboratory (LLNL) Staff, at the request of the U.S. Department of Energy (DOE), on the Safety Analysis Report for Packaging, Model 9975, Revision 0, dated January 2008 (S-SARP-G-00003, the SARP). The review includes an evaluation of the SARP, with respect to the requirements specified in 10 CFR 71, and in International Atomic Energy Agency (IAEA) Safety Standards Series No. TS-R-1. The Model 9975-96 Package is a 35-gallon drum package design that has evolved from a family of packages designed by DOE contractors at the Savannah River Site. Earlier package designs, i.e., the Model 9965, the Model 9966, the Model 9967, and the Model 9968 Packagings, were originally designed and certified in the early 1980s. In the 1990s, updated package designs that incorporated design features consistent with the then newer safety requirements were proposed. The updated package designs at the time were the Model 9972, the Model 9973, the Model 9974, and the Model 9975 Packagings, respectively. The Model 9975 Package was certified by the Packaging Certification Program, under the Office of Safety Management and Operations. The safety analysis of the Model 9975-85 Packaging is documented in the Safety Analysis Report for Packaging, Model 9975, B(M)F-85, Revision 0, dated December 2003. The Model 9975-85 Package is certified by DOE Certificate of Compliance (CoC) package identification number, USA/9975/B(M)F-85, for the transportation of Type B quantities of uranium metal/oxide, 238 Pu heat sources, plutonium/uranium metals, plutonium/uranium oxides, plutonium composites, plutonium/tantalum composites, 238 Pu oxide/beryllium metal.

Development of safety principles for the design of future nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

The main purpose of this TECDOC is to propose updates to existing safety principles which could be used as a basis for developing safety principles for the design of future NPPs. Accordingly, this document is intended to be useful to reactor designers, owners, operators, researchers and regulators. It is also expected that this document can contribute to international harmonization of safety approaches, and that it will help ensure that future reactors will be designed worldwide to a high standard of safety. As such, these proposed updates are intended to provide general guidance which, if carefully and properly implemented, will result in reactor designs with enhanced safety characteristics beyond those currently in operation. This enhancement results from the fact that the proposals are derived from the lessons learned from more recent operational experience, R and D, design, testing, and analysis developed over the past decade or so, as well as from attempts to reflect the current trends in reactor design, such as the introduction of new technologies. 8 refs, 3 figs.

Development of safety principles for the design of future nuclear power plants

International Nuclear Information System (INIS)

1995-06-01

The main purpose of this TECDOC is to propose updates to existing safety principles which could be used as a basis for developing safety principles for the design of future NPPs. Accordingly, this document is intended to be useful to reactor designers, owners, operators, researchers and regulators. It is also expected that this document can contribute to international harmonization of safety approaches, and that it will help ensure that future reactors will be designed worldwide to a high standard of safety. As such, these proposed updates are intended to provide general guidance which, if carefully and properly implemented, will result in reactor designs with enhanced safety characteristics beyond those currently in operation. This enhancement results from the fact that the proposals are derived from the lessons learned from more recent operational experience, R and D, design, testing, and analysis developed over the past decade or so, as well as from attempts to reflect the current trends in reactor design, such as the introduction of new technologies. 8 refs, 3 figs

A proposed approach for enhancing design safety assurance of future plants

International Nuclear Information System (INIS)

Oh, Kyu Myeng; Ahn, Sang Kyu; Lee, Chang Ju; Kim, Inn Seock

2010-01-01

This paper provides various insights from a detailed review of deterministic approaches typically applied to ensure design safety of nuclear power plants (NPPs) and risk-informed approaches proposed to evaluate safety of advanced reactors such as Generation IV reactors. Also considered herein are the risk-informed safety analysis (RISA) methodology suggested by Westinghouse as a means to improve the conventional accident analysis, together with the Technology Neutral Framework recently suggested by the U.S. NRC for safety evaluation of future plants. These insights from the comparative review of deterministic and risk-informed approaches could be used in further enhancing the methodology for design safety assurance of future plants

Model quality and safety studies

DEFF Research Database (Denmark)

Petersen, K.E.

1997-01-01

The paper describes the EC initiative on model quality assessment and emphasizes some of the problems encountered in the selection of data from field tests used in the evaluation process. Further, it discusses the impact of model uncertainties in safety studies of industrial plants. The model...... that most of these have never been through a procedure of evaluation, but nonetheless are used to assist in making decisions that may directly affect the safety of the public and the environment. As a major funder of European research on major industrial hazards, DGXII is conscious of the importance......-tain model is appropriate for use in solving a given problem. Further, the findings from the REDIPHEM project related to dense gas dispersion will be highlighted. Finally, the paper will discuss the need for model quality assessment in safety studies....

Application of Safety Maturity Model and 4P-4C Model in Safety Culture Assessment

International Nuclear Information System (INIS)

Choi, K. S.; Lee, Y. E.; Ha, J. T.; Chang, H. S.; Kam, S. C.

2010-01-01

Korean government and utility have made efforts to enhance the nuclear safety culture and the development of quantitative index of safety culture was promoted for past several years. Quantitative index of safety culture and the past efforts to understand safety culture need insight into the concept of culture. This paper aims to apply new method of measuring nuclear safety culture through the review of approaches of evaluating safety culture in non-nuclear industries. Scoring table has been developed based on new models and example of result of interviews evaluating the nuclear safety culture is also shown

Design basis and design features of WWER-440 model 213 nuclear power plants. Reference plant: Bohunice V2 (Slovakia)

International Nuclear Information System (INIS)

1994-05-01

The prime objective of the IAEA Technical Co-operation Project on Evaluation of Safety Aspects of WWER-440 model 213 NPPs is to co-ordinate and to integrate assistance to national organizations in studying selected aspects of safety for the same type of reactors. Consequently, the study integrated the results generated by national activities carried out in the Czech Republic, Hungary, Slovakia and Ukraine and co-ordinated through the IAEA. Valuable assistance in carrying out the tasks was also provided by Bulgaria and Poland. A set of publications is being prepared to present the results of the project. The publications are intended to facilitate the review and utilization of the results of the project. They are also providing assistance in further refinement and/or extension of plant specific safety evaluation of model 213 NPPs. This Technical Document addressing the design basis and safety related design features of WWER-440 model 213 plants is the first of the series to be published. It is hoped that this document will be useful to anyone working in the field of WWER safety, and in particular to experts planning, executing or reviewing studies related to the subject. Refs, 36 figs, tabs

Creation of a Sustainable Collaborative Transportation and Safety Model : Tech Transfer Summary

Science.gov (United States)

2018-03-23

The objective of this project was to create a sustainable asset management transportation and safety model for a designated area of St. Louis, Missouri, that can be replicated in other municipalities.

Safety and security aspects in design of digital safety I and C in nuclear power plants

International Nuclear Information System (INIS)

Ding, Yongjian; Waedt, Karl

2016-01-01

The paper describes a safety objective oriented systematic design approach of digital (computerized) safety I and C in modern nuclear power plants which considers the plant safety requirements as well as cybersecurity needs. The defence in depth philosophy is applied by using different defence lines in the I and C architecture and protection zones in the plant IT environment.

Safety and security aspects in design of digital safety I and C in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Ding, Yongjian [University of Applied Sciences Magdeburg-Stendal, Magdeburg (Germany). Inst. of Electrical Engineering; Waedt, Karl [Areva GmbH, Erlangen (Germany). PEAS-G

2016-05-15

The paper describes a safety objective oriented systematic design approach of digital (computerized) safety I and C in modern nuclear power plants which considers the plant safety requirements as well as cybersecurity needs. The defence in depth philosophy is applied by using different defence lines in the I and C architecture and protection zones in the plant IT environment.

Safety regulation for the design approval of special form radioactive sources

International Nuclear Information System (INIS)

Cho, Woon-Kap

2009-01-01

Several kinds of special form radioactive sources for industrial, medical applications are being produced in Korea. Special form radioactive sources should meet strict safety requirements specified in the domestic safety regulations and the design of the sources should be certified by the regulatory authority, the Ministry of Education, Science and Technology (MEST). Several safety tests such as impact, percussion, heating, and leak tests are performed on the sources according to the domestic regulations and the international safety standards such as ANSI N542-1977 and ISO 2919-1999(E). As a regulatory expert body, Korea Institute of Nuclear Safety (KINS) assesses various types of application documents, such as safety analysis report, quality assurance program, and other documents evidencing fulfillment of requirements for design approval of the special form radioactive sources, submitted by a legal person who intends to produce special form radioactive sources and then reports the assessment result to MEST. A design approval certificate is issued to the applicant by MEST on the basis of a technical evaluation report presented by KINS.

Safety design guides for containment extension for CANDU 9

International Nuclear Information System (INIS)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young; A. C. D. Wright

1996-03-01

This safety design guide for containment extension describes the containment isolation philosophy and containment extension requirements. The metal extensions and components falling within the scope of ASME Section III are classified in accordance with the CAN/CSA-N285.0 and CAN/CSA-N285.3. The special consideration for the leak monitoring capability, seismic qualification and inspection requirements for containment extensions, etc., are defined in this design guide. In addition, the containment isolation systems are defined and summarized schematically in appendix A. The change status of the regulatory requirements, code and standards should be traced and this safety design guide shall be updated accordingly. (Author) .new

Design of agricultural product quality safety retrospective supervision system of Jiangsu province

Science.gov (United States)

Wang, Kun

2017-08-01

In store and supermarkets to consumers can trace back agricultural products through the electronic province card to query their origin, planting, processing, packaging, testing and other important information and found that the problems. Quality and safety issues can identify the responsibility of the problem. This paper designs a retroactive supervision system for the quality and safety of agricultural products in Jiangsu Province. Based on the analysis of agricultural production and business process, the goal of Jiangsu agricultural product quality safety traceability system construction is established, and the specific functional requirements and non-functioning requirements of the retroactive system are analyzed, and the target is specified for the specific construction of the retroactive system. The design of the quality and safety traceability system in Jiangsu province contains the design of the overall design, the trace code design and the system function module.

Planning and architectural safety considerations in designing nuclear power plants

International Nuclear Information System (INIS)

Konsowa, Ahmed A.

2009-01-01

To achieve optimum safety and to avoid possible hazards in nuclear power plants, considering architectural design fundamentals and all operating precautions is mandatory. There are some planning and architectural precautions should be considered to achieve a high quality design and construction of nuclear power plant with optimum safety. This paper highlights predicted hazards like fire, terrorism, aircraft crash attacks, adversaries, intruders, and earthquakes, proposing protective actions against these hazards that vary from preventing danger to evacuating and sheltering people in-place. For instance; using safeguards program to protect against sabotage, theft, and diversion. Also, site and building well design focusing on escape pathways, emergency exits, and evacuation zones, and the safety procedures such as; evacuation exercises and sheltering processes according to different emergency classifications. In addition, this paper mentions some important codes and regulations that control nuclear power plants design, and assessment methods that evaluate probable risks. (author)

Safety and environmental aspects in LNG carrier design

International Nuclear Information System (INIS)

Takashi Yoneyama

1997-01-01

'Safety and Reliability' has been and will continue to be a key phr ase in marine transportation of LNG. Mitsui Engineering and Shipbuilding Co.,Ltd. has utilized its all expertise and state of art technologies to realize this objective, resulting in exceptionally successful operations of LNG carrier built by the Co. In line with growing global concern about environmental issues, we need to pay more attention to the environmental aspects of the design and construction of LNG carriers. Accordingly, in this paper, we present some topics related safety and environmental concerns which need to be taken into consideration in LNG carriers design and construction. (Author). 7 figs

Safety and environmental aspects in LNG carrier design

Energy Technology Data Exchange (ETDEWEB)

Yoneyama, Takashi [Mitsui Shipbuilding and Engineering Co. Ltd., Tokyo (Japan)

1997-06-01

`Safety and Reliability` has been and will continue to be a key phr ase in marine transportation of LNG. Mitsui Engineering and Shipbuilding Co.,Ltd. has utilized its all expertise and state of art technologies to realize this objective, resulting in exceptionally successful operations of LNG carrier built by the Co. In line with growing global concern about environmental issues, we need to pay more attention to the environmental aspects of the design and construction of LNG carriers. Accordingly, in this paper, we present some topics related safety and environmental concerns which need to be taken into consideration in LNG carriers design and construction. (Author). 7 figs.

Safety Design Requirements for The Interior Architecture of Scientific Research Laboratories

International Nuclear Information System (INIS)

ElDib, A.A.

2014-01-01

The paper discusses one of the primary objectives of interior architecture design of research laboratories (specially those using radioactive materials) where it should provide a safe, accessible environment for laboratory personnel to conduct their work. A secondary objective is to allow for maximum flexibility for safe research. Therefore, health and safety hazards must be anticipated and carefully evaluated so that protective measures can be incorporated into the interior architectural design of these facilities wherever possible. The interior architecture requirements discussed in this paper illustrate some of the basic health and safety design features required for new and remodeled laboratories.The paper discusses one of the primary objectives of interior architecture design of research laboratories (specially those using radioactive materials) where it should provide a safe, accessible environment for laboratory personnel to conduct their work. A secondary objective is to allow for maximum flexibility for safe research. Therefore, health and safety hazards must be anticipated and carefully evaluated so that protective measures can be incorporated into the interior architectural design of these facilities wherever possible. The interior architecture requirements discussed in this paper illustrate some of the basic health and safety design features required for new and remodeled laboratories.

Performance and safety design of the advanced liquid metal reactor

International Nuclear Information System (INIS)

Berglund, R.C.; Magee, P.M.; Boardman, C.E.; Gyorey, G.L.

1991-01-01

The Advanced Liquid Metal Reactor (ALMR) program led by General Electric is developing, under U.S. Department of Energy sponsorship, a conceptual design for an advanced sodium-cooled liquid metal reactor plant. This design is intended to improve the already excellent level of plant safety achieved by the nuclear power industry while at the same time providing significant reductions in plant construction and operating costs. In this paper, the plant design and performance are reviewed, with emphasis on the ALMR's unique passive design safety features and its capability to utilize as fuel the actinides in LWR spent fuel

Research on conceptual design of simplified nuclear safety instrument and control system

International Nuclear Information System (INIS)

Huang Jie

2015-01-01

The Nuclear safety instrument and control system is directly related to the safety of the reactor. So redundant and diversity design is used to ensure the system's security and reliability. This make the traditional safety system large, more cabinets and wiring complexity. To solve these problem, we can adopt new technology to make the design more simple. The simplify conceptual design can make the system less cabinets, less wiring, but high security, strong reliability. (author)

Code on the safety of nuclear power plants: Design

International Nuclear Information System (INIS)

1988-01-01

This Code is a compilation of nuclear safety principles aimed at defining the essential requirements necessary to ensure nuclear safety. These requirements are applicable to structures, systems and components, and procedures important to safety in nuclear power plants embodying thermal neutron reactors, with emphasis on what safety requirements shall be met rather than on specifying how these requirements can be met. It forms part of the Agency's programme for establishing Codes and Safety Guides relating to land based stationary thermal neutron power plants. The document should be used by organizations designing, manufacturing, constructing and operating nuclear power plants as well as by regulatory bodies

An experimental study on passive safety systems for the SMART design with the SMART-ITL facility

International Nuclear Information System (INIS)

Park, Hyun-Sik; Bae, Hwang; Ryu, Sung-Uk; Jeon, Byong-Guk; Yang, Jin-Hwa; Yi, Sung-Jae

2016-01-01

Passive Safety Systems (PSSs) are added to the SMART design to increase the safety margin during accidents especially under a prolonged station blackout. A set of validation tests were performed for the PSSs of the SMART design with an integral effect test loop of SMART-ITL. Both single and dual trains of the Passive Safety Injection System (PSIS) were simulated to validate the SMART design together with two stages of Automatic Depressurization System (ADS) and four trains of Passive Residual Heat Removal System (PRHRS), and their results were compared. In this paper, the effect of the train number of PSIS on a Small-Break Loss of Coolant Accident (SBLOCA) scenario is investigated for a break size of 0.4 inch. The single and dual train tests show a similar trend in general but the injected water migrates slightly differently in the RV and is discharged through the break nozzle. The parameters of the Reactor Vessel (RV) pressure, RV water level, accumulated break mass, and injection flowrates from the Core Makeup Tank (CMT) and Safety Injection Tank (SIT) were compared. The acquired data will be used to validate the safety analysis code and its related models to evaluate the performance of SMART PSS, and to provide the base data during the application phase of construction licensing of the SMART design. (author)

Radiation protection aspects in the design of nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2008-01-01

The IAEA's Statute authorizes the Agency to establish safety standards to protect health and minimize danger to life and property - standards which the IAEA must use in its own operations, and which a State can apply by means of its regulatory provisions for nuclear and radiation safety. A comprehensive body of safety standards under regular review, together with the IAEA's assistance in their application, has become a key element in a global safety regime. In the mid-1990s, a major overhaul of the IAEA's safety standards programme was initiated, with a revised oversight committee structure and a systematic approach to updating the entire corpus of standards. The new standards that have resulted are of a high calibre and reflect best practices in Member States. With the assistance of the Commission on Safety Standards, the IAEA is working to promote the global acceptance and use of its safety standards. Safety standards are only effective, however, if they are properly applied in practice. The IAEA's safety services - which range in scope from engineering safety, operational safety, and radiation, transport and waste safety to regulatory matters and safety culture in organizations - assist Member States in applying the standards and appraise their effectiveness. These safety services enable valuable insights to be shared and continue to urge all Member States to make use of them. Regulating nuclear and radiation safety is a national responsibility, and many Member States have decided to adopt the IAEA's safety standards for use in their national regulations. For the Contracting Parties to the various international safety conventions, IAEA standards provide a consistent, reliable means of ensuring the effective fulfilment of obligations under the conventions. The standards are also applied by designers, manufacturers and operators around the world to enhance nuclear and radiation safety in power generation, medicine, industry, agriculture, research and education

Radiation shielding and safety design

Energy Technology Data Exchange (ETDEWEB)

Lee, Yong Ouk; Gil, C. S.; Cho, Y. S.; Kim, D. H.; Kim, H. I.; Kim, J. W.; Lee, C. W.; Kim, K. Y.; Kim, B. H. [KAERI, Daejeon (Korea, Republic of)

2011-07-15

A benchmarking for the test facility, evaluations of the prompt radiation fields, evaluation of the induced activities in the facility, and estimation of the radiological impact on the environment were performed in this study. and the radiation safety analysis report for nuclear licensing was written based on this study. In the benchmark calculation, the neutron spectra was measured in the 20 Mev test facility and the measurements were compared with the computational results to verify the calculation system. In the evaluation of the prompt radiation fields, the shielding design for 100 MeV target rooms, evaluations of the leakage doses from the accidents and skyshine analysis were performed. The evaluation of the induced activities were performed for the coolant, inside air, structural materials, soil and ground-water. At last, the radiation safety analysis report was written based on results from these studies

Physical design correlates of efficiency and safety in emergency departments: a qualitative examination.

Science.gov (United States)

Pati, Debajyoti; Harvey, Thomas E; Pati, Sipra

2014-01-01

The objective of this study was to explore and identify physical design correlates of safety and efficiency in emergency department (ED) operations. This study adopted an exploratory, multimeasure approach to (1) examine the interactions between ED operations and physical design at 4 sites and (2) identify domains of physical design decision-making that potentially influence efficiency and safety. Multidisciplinary gaming and semistructured interviews were conducted with stakeholders at each site. Study data suggest that 16 domains of physical design decisions influence safety, efficiency, or both. These include (1) entrance and patient waiting, (2) traffic management, (3) subwaiting or internal waiting areas, (4) triage, (5) examination/treatment area configuration, (6) examination/treatment area centralization versus decentralization, (7) examination/treatment room standardization, (8) adequate space, (9) nurse work space, (10) physician work space, (11) adjacencies and access, (12) equipment room, (13) psych room, (14) staff de-stressing room, (15) hallway width, and (16) results waiting area. Safety and efficiency from a physical environment perspective in ED design are mutually reinforcing concepts--enhancing efficiency bears positive implications for safety. Furthermore, safety and security emerged as correlated concepts, with security issues bearing implications for safety, thereby suggesting important associations between safety, security, and efficiency.

The European space suit, a design for productivity and crew safety

Science.gov (United States)

Skoog, A. Ingemar; Berthier, S.; Ollivier, Y.

In order to fulfil the two major mission objectives, i.e. support planned and unplanned external servicing of the COLUMBUS FFL and support the HERMES vehicle for safety critical operations and emergencies, the European Space Suit System baseline configuration incorporates a number of design features, which shall enhance the productivity and the crew safety of EVA astronauts. The work in EVA is today - and will be for several years - a manual work. Consequently, to improve productivity, the first challenge is to design a suit enclosure which minimizes movement restrictions and crew fatigue. It is covered by the "ergonomic" aspect of the suit design. Furthermore, it is also necessary to help the EVA crewmember in his work, by giving him the right information at the right time. Many solutions exist in this field of Man-Machine Interface, from a very simple system, based on cuff check lists, up to advanced systems, including Head-Up Displays. The design concept for improved productivity encompasses following features: • easy donning/doffing thru rear entry, • suit ergonomy optimisation, • display of operational information in alpha-numerical and graphical from, and • voice processing for operations and safety critical information. Concerning crew safety the major design features are: • a lower R-factor for emergency EVA operations thru incressed suit pressure, • zero prebreath conditions for normal operations, • visual and voice processing of all safety critical functions, and • an autonomous life support system to permit unrestricted operations around HERMES and the CFFL. The paper analyses crew safety and productivity criteria and describes how these features are being built into the design of the European Space Suit System.

Graphical symbols -- Safety colours and safety signs -- Part 1: Design principles for safety signs in workplaces and public areas

CERN Document Server

International Organization for Standardization. Geneva

2002-01-01

This International Standard establishes the safety identification colours and design principles for safety signs to be used in workplaces and in public areas for the purpose of accident prevention, fire protection, health hazard information and emergency evacuation. It also establishes the basic principles to be applied when developing standards containing safety signs. This part of ISO 3864 is applicable to workplaces and all locations and all sectors where safety-related questions may be posed. However, it is not applicable to the signalling used for guiding rail, road, river, maritime and air traffic and, generally speaking, to those sectors subject to a regulation which may differ.

Children's choice: Color associations in children's safety sign design.

Science.gov (United States)

Siu, Kin Wai Michael; Lam, Mei Seung; Wong, Yi Lin

2017-03-01

Color has been more identified as a key consideration in ergonomics. Color conveys messages and is an important element in safety signs, as it provides extra information to users. However, very limited recent research has focused on children and their color association in the context of safety signs. This study thus examined how children use colors in drawing different safety signs and how they associate colors with different concepts and objects that appear in safety signs. Drawing was used to extract children's use of color and the associations they made between signs and colors. The child participants were given 12 referents of different safety signs and were asked to design and draw the signs using different colored felt-tip pens. They were also asked to give reasons for their choices of colors. Significant associations were found between red and 'don't', orange and 'hands', and blue and 'water'. The child participants were only able to attribute the reasons for the use of yellow, green, blue and black through concrete identification and concrete association, and red through abstract association. The children's use of color quite differs from that shown in the ISO registered signs. There is a need to consider the use of colors carefully when designing signs specifically for children. Sign designers should take children's color associations in consideration and be aware if there are any misunderstandings. Copyright © 2016 Elsevier Ltd. All rights reserved.

Laser safety in design of near-infrared scanning LIDARs

Science.gov (United States)

Zhu, X.; Elgin, D.

2015-05-01

3D LIDARs (Light Detection and Ranging) with 1.5μm nanosecond pulse lasers have been increasingly used in different applications. The main reason for their popularity is that these LIDARs have high performance while at the same time can be made eye-safe. Because the laser hazard effect on eyes or skin at this wavelength region (industrial mining applications. We have incorporated the laser safety requirements in the LIDAR design and conducted laser safety analysis for different operational scenarios. While 1.5μm is normally said to be the eye-safe wavelength, in reality a high performance 3D LIDAR needs high pulse energy, small beam size and high pulse repetition frequency (PRF) to achieve long range, high resolution and high density images. The resulting radiant exposure of its stationary beam could be many times higher than the limit for a Class 1 laser device. Without carefully choosing laser and scanning parameters, including field-of-view, scan speed and pattern, a scanning LIDAR can't be eye- or skin-safe based only on its wavelength. This paper discusses the laser safety considerations in the design of eye-safe scanning LIDARs, including laser pulse energy, PRF, beam size and scanning parameters in two basic designs of scanning mechanisms, i.e. galvanometer based scanner and Risley prism based scanner. The laser safety is discussed in terms of device classification, nominal ocular hazard distance (NOHD) and safety glasses optical density (OD).

International cooperation in the safety and environmental assessment for the ITER engineering design activities

International Nuclear Information System (INIS)

Gordon, C.; Baker, D.J.; Bartels, H-W.

1998-01-01

The ITER Project includes design and assessment activities to ensure the safety and environmental attractiveness of ITER and demonstrate that it can be sited in any of the sponsoring Parties with a minimum of site-specific redesign. This paper highlights some of the efforts to develop an international consensus approach for ITER safety design and assessment, including: development of general safety and environmental design criteria; development of quantitative dose-release assessment criteria; development of a radiation protection program; waste characterization; and development of safety analysis guidelines. The high level of interaction, cooperation and collaboration between the Joint Central Team and the Home Teams, and between the safety team and designers, and the spirit of consensus that has guided them have resulted in a safe design for ITER and a safety design and assessment that can meet the needs of the potential host countries. (author)

Safety aspects of designs for future light water reactors (evolutionary reactors)

International Nuclear Information System (INIS)

1993-07-01

The main purpose of this document is to describe the major innovations of proposed designs of future light water reactors, to describe specific safety characteristics and safety analysis methodologies, and to give a general overview of the most important safety aspects related to future reactors. The reactors considered in this report are limited to those intended for fixed station electrical power production, excluding most revolutionary concepts. More in depth discussion is devoted to those designs that are in a more advanced state of completion and have been more extensively described and analysed in the open literature. Other designs will be briefly described, as evidence of the large spectrum of new proposals. Some designs are similar; others implement unique features and require specific discussion (not all aspects of designs with unique features are fully discussed in this document). 131 refs, 22 figs

External Events Excluding Earthquakes in the Design of Nuclear Power Plants. Safety Guide

International Nuclear Information System (INIS)

2008-01-01

This Safety Guide provides recommendations and guidance on design for the protection of nuclear power plants from the effects of external events (excluding earthquakes), i.e. events that originate either off the site or within the boundaries of the site but from sources that are not directly involved in the operational states of the nuclear power plant units. In addition, it provides recommendations on engineering related matters in order to comply with the safety objectives and requirements established in the IAEA Safety Requirements publication, Safety of Nuclear Power Plants: Design. It is also applicable to the design and safety assessment of items important to the safety of land based stationary nuclear power plants with water cooled reactors. Contents: 1. Introduction; 2. Application of safety criteria to the design; 3. Design basis for external events; 4. Aircraft crash; 5. External fire; 6. Explosions; 7. Asphyxiant and toxic gases; 8. Corrosive and radioactive gases and liquids; 9. Electromagnetic interference; 10. Floods; 11. Extreme winds; 12. Extreme meteorological conditions; 13. Biological phenomena; 14. Volcanism; 15. Collisions of floating bodies with water intakes and UHS components; Annex I: Aircraft crashes; Annex II: Detonation and deflagration; Annex III: Toxicity limits.

Design of Safety Parameter Monitoring Function in a Research Reactor Facility

Energy Technology Data Exchange (ETDEWEB)

Park, Jaekwan; Suh, Yongsuk [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

The primary purpose of the safety parameter monitoring system (SPDS) is to help operating personnel in the control room make quick assessments of the plant safety status. Thus, the basic function of the SPDS is a provision of a continuous indication of plant parameters or derived variables representative of the safety status of the plant. NUREG-0737 Supplement 1 provides details of the functional criteria for the SPDS, as one of the action plan requirements from TMI accident. The system provides various functions as follows: · Alerting based on safety function decision logics, · Success path analysis to achieve the integrity of the safety functions, · 3 layer display architecture - safety function, success path display for each safety function, system summary and equipment details for each safety function, · Integration with computer-based procedure. According to a Notice of the NSSC No. 2012-31, a research reactor facility generating more than 2 MW of power should also be furnished with the SPDS for emergency preparedness. Generally, a research reactor is a small size facility, and its number of instrumentations is fewer than that of NPPs. In particular, it is actually hard to have various and powerful functions from an economic perspective. Therefore, a safety parameter display system optimized for a research reactor facility must be proposed. This paper provides the requirement analysis results and proposes the design of safety parameter monitoring function for a research reactor. The safety parameter monitoring function supporting control room personnel during emergency conditions should be designed in a research reactor facility. The facility size and number of signals are smaller than that of the power plants. Also, it is actually hard to have various and powerful functions of nuclear power plants from an economic perspective. Thus, a safety parameter display system optimized to a research reactor must be proposed. First, we found important design items

Design of Safety Parameter Monitoring Function in a Research Reactor Facility

International Nuclear Information System (INIS)

Park, Jaekwan; Suh, Yongsuk

2014-01-01

The primary purpose of the safety parameter monitoring system (SPDS) is to help operating personnel in the control room make quick assessments of the plant safety status. Thus, the basic function of the SPDS is a provision of a continuous indication of plant parameters or derived variables representative of the safety status of the plant. NUREG-0737 Supplement 1 provides details of the functional criteria for the SPDS, as one of the action plan requirements from TMI accident. The system provides various functions as follows: · Alerting based on safety function decision logics, · Success path analysis to achieve the integrity of the safety functions, · 3 layer display architecture - safety function, success path display for each safety function, system summary and equipment details for each safety function, · Integration with computer-based procedure. According to a Notice of the NSSC No. 2012-31, a research reactor facility generating more than 2 MW of power should also be furnished with the SPDS for emergency preparedness. Generally, a research reactor is a small size facility, and its number of instrumentations is fewer than that of NPPs. In particular, it is actually hard to have various and powerful functions from an economic perspective. Therefore, a safety parameter display system optimized for a research reactor facility must be proposed. This paper provides the requirement analysis results and proposes the design of safety parameter monitoring function for a research reactor. The safety parameter monitoring function supporting control room personnel during emergency conditions should be designed in a research reactor facility. The facility size and number of signals are smaller than that of the power plants. Also, it is actually hard to have various and powerful functions of nuclear power plants from an economic perspective. Thus, a safety parameter display system optimized to a research reactor must be proposed. First, we found important design items

Safety and design impact of hurricane Andrew

International Nuclear Information System (INIS)

Guey, Ching N.

2004-01-01

Turkey Point completed the IPE in June of 1991. Hurricane Andrew landed at Turkey Point on August 24, 1992. Although the safety related systems, components and structures were not damaged by the Hurricane Andrew, certain nonsafety related components and the neighboring fossil plant sustained noticeable damage. Among the major components that were nonsafety related but would affect the PRA of the plant included the service water pumps and the high tower. This paper discusses the safety and design impact of Hurricane Andrew on Turkey Point Nuclear Power Plant. The risk of hurricanes on the interim and evolving plant configurations are briefly described. The risk of the plant from internal events as a result of damage incurred during Hurricane Andrew are discussed. The design change as the result of Hurricane Andrew and its impact on the PRA are presented. (author)

Animal models for microbicide safety and efficacy testing.

Science.gov (United States)

Veazey, Ronald S

2013-07-01

Early studies have cast doubt on the utility of animal models for predicting success or failure of HIV-prevention strategies, but results of multiple human phase 3 microbicide trials, and interrogations into the discrepancies between human and animal model trials, indicate that animal models were, and are, predictive of safety and efficacy of microbicide candidates. Recent studies have shown that topically applied vaginal gels, and oral prophylaxis using single or combination antiretrovirals are indeed effective in preventing sexual HIV transmission in humans, and all of these successes were predicted in animal models. Further, prior discrepancies between animal and human results are finally being deciphered as inadequacies in study design in the model, or quite often, noncompliance in human trials, the latter being increasingly recognized as a major problem in human microbicide trials. Successful microbicide studies in humans have validated results in animal models, and several ongoing studies are further investigating questions of tissue distribution, duration of efficacy, and continued safety with repeated application of these, and other promising microbicide candidates in both murine and nonhuman primate models. Now that we finally have positive correlations with prevention strategies and protection from HIV transmission, we can retrospectively validate animal models for their ability to predict these results, and more importantly, prospectively use these models to select and advance even safer, more effective, and importantly, more durable microbicide candidates into human trials.

Modeling of requirement specification for safety critical real time computer system using formal mathematical specifications

International Nuclear Information System (INIS)

Sankar, Bindu; Sasidhar Rao, B.; Ilango Sambasivam, S.; Swaminathan, P.

2002-01-01

Full text: Real time computer systems are increasingly used for safety critical supervision and control of nuclear reactors. Typical application areas are supervision of reactor core against coolant flow blockage, supervision of clad hot spot, supervision of undesirable power excursion, power control and control logic for fuel handling systems. The most frequent cause of fault in safety critical real time computer system is traced to fuzziness in requirement specification. To ensure the specified safety, it is necessary to model the requirement specification of safety critical real time computer systems using formal mathematical methods. Modeling eliminates the fuzziness in the requirement specification and also helps to prepare the verification and validation schemes. Test data can be easily designed from the model of the requirement specification. Z and B are the popular languages used for modeling the requirement specification. A typical safety critical real time computer system for supervising the reactor core of prototype fast breeder reactor (PFBR) against flow blockage is taken as case study. Modeling techniques and the actual model are explained in detail. The advantages of modeling for ensuring the safety are summarized

Physics design of fast reactor safety test facilities for in-pile experiments

International Nuclear Information System (INIS)

Travelli, A.; Matos, J.E.; Snelgrove, J.L.; Shaftman, D.H.; Tzanos, C.P.; Lam, S.K.; Pennington, E.M.; Woodruff, W.L.

1976-01-01

A determined effort to identify and resolve current Fast Breeder Reactor safety testing needs has recently resulted in a number of conceptual designs for FBR safety test facilities which are very complex and diverse both in their features and in their purpose. The paper discusses the physics foundations common to most fast reactor safety test facilities and the constraints which they impose on the design. The logical evolution, features, and capabilities of several major conceptual designs are discussed on the basis of this common background

Applying different quality and safety models in healthcare improvement work: Boundary objects and system thinking

International Nuclear Information System (INIS)

Wiig, Siri; Robert, Glenn; Anderson, Janet E.; Pietikainen, Elina; Reiman, Teemu; Macchi, Luigi; Aase, Karina

2014-01-01

A number of theoretical models can be applied to help guide quality improvement and patient safety interventions in hospitals. However there are often significant differences between such models and, therefore, their potential contribution when applied in diverse contexts. The aim of this paper is to explore how two such models have been applied by hospitals to improve quality and safety. We describe and compare the models: (1) The Organizing for Quality (OQ) model, and (2) the Design for Integrated Safety Culture (DISC) model. We analyze the theoretical foundations of the models, and show, by using a retrospective comparative case study approach from two European hospitals, how these models have been applied to improve quality and safety. The analysis shows that differences appear in the theoretical foundations, practical approaches and applications of the models. Nevertheless, the case studies indicate that the choice between the OQ and DISC models is of less importance for guiding the practice of quality and safety improvement work, as they are both systemic and share some important characteristics. The main contribution of the models lay in their role as boundary objects directing attention towards organizational and systems thinking, culture, and collaboration

Operational characteristics of nuclear power plants - modelling of operational safety

International Nuclear Information System (INIS)

Studovic, M.

1984-01-01

By operational experience of nuclear power plants and realize dlevel of availability of plant, systems and componenst reliabiliuty, operational safety and public protection, as a source on nature of distrurbances in power plant systems and lessons drawn by the TMI-2, in th epaper are discussed: examination of design safety for ultimate ensuring of safe operational conditions of the nuclear power plant; significance of the adequate action for keeping proess parameters in prescribed limits and reactor cooling rquirements; developed systems for measurements detection and monitoring all critical parameters in the nuclear steam supply system; contents of theoretical investigation and mathematical modeling of the physical phenomena and process in nuclear power plant system and components as software, supporting for ensuring of operational safety and new access in staff education process; program and progress of the investigation of some physical phenomena and mathematical modeling of nuclear plant transients, prepared at faculty of mechanical Engineering in Belgrade. (author)

A review of models relevant to road safety.

Science.gov (United States)

Hughes, B P; Newstead, S; Anund, A; Shu, C C; Falkmer, T

2015-01-01

It is estimated that more than 1.2 million people die worldwide as a result of road traffic crashes and some 50 million are injured per annum. At present some Western countries' road safety strategies and countermeasures claim to have developed into 'Safe Systems' models to address the effects of road related crashes. Well-constructed models encourage effective strategies to improve road safety. This review aimed to identify and summarise concise descriptions, or 'models' of safety. The review covers information from a wide variety of fields and contexts including transport, occupational safety, food industry, education, construction and health. The information from 2620 candidate references were selected and summarised in 121 examples of different types of model and contents. The language of safety models and systems was found to be inconsistent. Each model provided additional information regarding style, purpose, complexity and diversity. In total, seven types of models were identified. The categorisation of models was done on a high level with a variation of details in each group and without a complete, simple and rational description. The models identified in this review are likely to be adaptable to road safety and some of them have previously been used. None of systems theory, safety management systems, the risk management approach, or safety culture was commonly or thoroughly applied to road safety. It is concluded that these approaches have the potential to reduce road trauma. Copyright © 2014 Elsevier Ltd. All rights reserved.

GT-MHR design, performance, and safety

International Nuclear Information System (INIS)

Neylan, A.J.; Shenoy, A.; Silady, F.A.; Dunn, T.D.

1994-11-01

The Gas Turbine-Modular Helium Reactor (GT-MHR) is the result of coupling the evolution of a low power density passively safe modular reactor with key technology developments in the U.S. during the last decade: large industrial gas turbines; large active magnetic bearings; and compact, highly effective plate-fin heat exchangers. This is accomplished through the unique use of the Brayton cycle to produce electricity with the helium as primary coolant from the reactor directly driving the gas turbine electrical generator. This cycle can achieve a high net efficiency in the range of 45% to 48%. In the design of the GT-MHR the desirable inherent characteristics of the inert helium coolant, graphite core, and the coated fuel particles are supplemented with specific design features such as passive heat removal to achieve the safety objective of not disturbing the normal day-to-day activities of the public even for beyond design basis rare accidents. Each GT-MHR plant consists of four modules. The GT-MHR module components are contained within steel pressure vessels: a reactor vessel, a power conversion vessel, and a connecting cross vessel. All vessels are sited underground in a concrete silo, which serves as an independent vented low pressure containment structure. By capitalizing on industrial and aerospace gas turbine development, highly effective heat exchanger designs, and inherent gas cooled reactor temperature characteristics, the passively safe GT-MHR provides a sound technical, monetary, and environmental basis for new nuclear power generating capacity. This paper provides an update on the status of the design, which has been under development on the US-DOE program since February 1993. An assessment of plant performance and safety is also included

MODULAR AND FULL SIZE SIMPLIFIED BOILING WATER REACTOR DESIGN WITH FULLY PASSIVE SAFETY SYSTEMS

International Nuclear Information System (INIS)

Ishii, M.; Revankar, S. T.; Downar, T.; Xu, Y.; Yoon, H. J.; Tinkler, D.; Rohatgi, U. S.

2003-01-01

system scaling analysis, design parameters were obtained and designs of the compact modular 200 MWe SBWR and the full size 1200 MWe SBWR were developed. These reactors are provided with passive safety systems. A new passive vacuum breaker check valve was designed to replace the mechanical vacuum beaker check valve. The new vacuum breaker check valve was based on a hydrostatic head, and was fail safe. The performance of this new valve was evaluated both by the thermal-hydraulic code RELAP5 and by the experiments in a scaled SBWR facility, PUMA. In the core neutronic design a core depletion model was implemented to PARCS code. A lattice design for the SBWR fuel assemblies was performed. Design improvements were made to the neutronics/thermal-hydraulics models of SBWR-200 and SBWR-1200, and design analyses of these reactors were performed. The design base accident analysis and evaluation of all the passive safety systems were completed as scheduled in tasks 4 and 5. Initial conditions for the small break loss of coolant accidents (LOCA) and large break LOCA using REALP5 code were obtained. Small and large break LOCA tests were performed and the data was analyzed. An anticipated transient with scram was simulated using the RELAP5 code for SBWR-200. The transient considered was an accidental closure of the main steam isolation valve (MSIV), which was considered to be the most significant transient. The evaluation of the RELAP5 code against experimental data for SBWR-1200 was completed. In task 6, the instability analysis for the three SBWR designs (SBWR-1200, SBWR-600 and SBWR-200) were simulated for start-up transients and the results were similar. Neither the geysering instability, nor the loop type instability was predicted by RAMONA-4B in the startup simulation following the recommended procedure by GE. The density wave oscillation was not observed at all because the power level used in the simulation was not high enough. A study was made of the potential instabilities by

Risk-informed approach for safety, safeguards, and security (3S) by design

International Nuclear Information System (INIS)

Suzuki, Mitsutoshi; Burr, Tom; Howell, John

2011-01-01

Over several decades the nuclear energy society worldwide has developed safety assessment methodology based on probabilistic risk analysis for incorporating its benefit into design and accident prevention for nuclear reactors. Although safeguards and security communities have different histories and technical aspects compared to safety, risk assessment as a supplement to their current requirements could be developed to promote synergism between Safety, Safeguards, and Security (3S) and to install effective countermeasures in the design of complex nuclear fuel cycle facilities. Since the 3S initiative was raised by G8 countries at Hokkaido Toyako-Summit in 2008, one approach to developing synergism in a 3S By Design (3SBD) process has been the application of risk-oriented assessment methodology. In the existing regulations of safeguards and security, a risk notion has already been considered for inherent threat and hazard recognition. To integrate existing metrics into a risk-oriented approach, several mathematical methods have already been surveyed, with attention to the scarcity of intentional acts in the case of safeguards and the sparseness of actual event data. A two-dimensional probability distribution composed of measurement error and incidence probabilities has been proposed to formalize inherent difficulties in the International Atomic Energy Agency (IAEA) safeguards criteria. In particular, the incidence probability that is difficult to estimate has been explained using a Markov model and game theory. In this work, a feasibility study of 3SBD is performed for an aqueous reprocessing process, and synergetic countermeasures are presented for preliminary demonstration of 3SBD. Although differences and conflicts between individual 'S' communities exist, the integrated approach would be valuable for optimization and balance between the 3S design features as well as for effective and efficient implementation under existing regulation frameworks. In addition

Two important safety-related verification tests in the design of Qinshan NPP 600 MWe reactor

International Nuclear Information System (INIS)

Li Pengzhou; Li Tianyong; Yu Danping; Sun Lei

2005-01-01

This paper summarizes two most important verification tests performed in the design of reactor of Qinshan NPP Phase II: seismic qualification test of control rod drive line (CRDL), flow-induced vibration test of reactor internals both in 1:5 scaled model and on-site measurement during heat function testing (HFT). Both qualification tests proved that the structural design of the reactor has large safety margin. (authors)

Design characteristics for pressurized water small modular nuclear power reactors with focus on safety

Energy Technology Data Exchange (ETDEWEB)

Kani, Iraj Mahmoudzadeh [Tehran Univ. (Iran, Islamic Republic of). Civil Faculty; Zandieh, Mehdi [Tehran Univ. (Iran, Islamic Republic of). Civil Faculty; International Univ. of Imam Khomeini (Iran, Islamic Republic of). Architecture Faculty; Abadi, Saeed Kheirollahi Hossein [International Univ. of Imam Khomeini (Iran, Islamic Republic of). Architecture Faculty

2016-05-15

Small Modular Reactors (SMRs) are a technology, attracting attention. Light water SMR possess an upgraded design case and emphasize the significance of integral models. Beside of these advantages, SMRs has faced numerous challenges, e.g. licensing, cost/investment, safety and security observation, social and environmental issues in building new plants.

Design verification enhancement of field programmable gate array-based safety-critical I&C system of nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Ibrahim [Department of Nuclear Engineering, Kyung Hee University, 1732 Deogyeong-daero, Giheung-gu, Yongin-si, Gyeonggi-do 17104 (Korea, Republic of); Jung, Jaecheon, E-mail: jcjung@kings.ac.kr [Department of Nuclear Power Plant Engineering, KEPCO International Nuclear Graduate School, 658-91 Haemaji-ro, Seosang-myeon, Ulju-gun, Ulsan 45014 (Korea, Republic of); Heo, Gyunyoung [Department of Nuclear Engineering, Kyung Hee University, 1732 Deogyeong-daero, Giheung-gu, Yongin-si, Gyeonggi-do 17104 (Korea, Republic of)

2017-06-15

Highlights: • An enhanced, systematic and integrated design verification approach is proposed for V&V of FPGA-based I&C system of NPP. • RPS bistable fixed setpoint trip algorithm is designed, analyzed, verified and discussed using the proposed approaches. • The application of integrated verification approach simultaneously verified the entire design modules. • The applicability of the proposed V&V facilitated the design verification processes. - Abstract: Safety-critical instrumentation and control (I&C) system in nuclear power plant (NPP) implemented on programmable logic controllers (PLCs) plays a vital role in safe operation of the plant. The challenges such as fast obsolescence, the vulnerability to cyber-attack, and other related issues of software systems have currently led to the consideration of field programmable gate arrays (FPGAs) as an alternative to PLCs because of their advantages and hardware related benefits. However, safety analysis for FPGA-based I&C systems, and verification and validation (V&V) assessments still remain important issues to be resolved, which are now become a global research point of interests. In this work, we proposed a systematic design and verification strategies from start to ready-to-use in form of model-based approaches for FPGA-based reactor protection system (RPS) that can lead to the enhancement of the design verification and validation processes. The proposed methodology stages are requirement analysis, enhanced functional flow block diagram (EFFBD) models, finite state machine with data path (FSMD) models, hardware description language (HDL) code development, and design verifications. The design verification stage includes unit test – Very high speed integrated circuit Hardware Description Language (VHDL) test and modified condition decision coverage (MC/DC) test, module test – MATLAB/Simulink Co-simulation test, and integration test – FPGA hardware test beds. To prove the adequacy of the proposed

Design verification enhancement of field programmable gate array-based safety-critical I&C system of nuclear power plant

International Nuclear Information System (INIS)

Ahmed, Ibrahim; Jung, Jaecheon; Heo, Gyunyoung

2017-01-01

Highlights: • An enhanced, systematic and integrated design verification approach is proposed for V&V of FPGA-based I&C system of NPP. • RPS bistable fixed setpoint trip algorithm is designed, analyzed, verified and discussed using the proposed approaches. • The application of integrated verification approach simultaneously verified the entire design modules. • The applicability of the proposed V&V facilitated the design verification processes. - Abstract: Safety-critical instrumentation and control (I&C) system in nuclear power plant (NPP) implemented on programmable logic controllers (PLCs) plays a vital role in safe operation of the plant. The challenges such as fast obsolescence, the vulnerability to cyber-attack, and other related issues of software systems have currently led to the consideration of field programmable gate arrays (FPGAs) as an alternative to PLCs because of their advantages and hardware related benefits. However, safety analysis for FPGA-based I&C systems, and verification and validation (V&V) assessments still remain important issues to be resolved, which are now become a global research point of interests. In this work, we proposed a systematic design and verification strategies from start to ready-to-use in form of model-based approaches for FPGA-based reactor protection system (RPS) that can lead to the enhancement of the design verification and validation processes. The proposed methodology stages are requirement analysis, enhanced functional flow block diagram (EFFBD) models, finite state machine with data path (FSMD) models, hardware description language (HDL) code development, and design verifications. The design verification stage includes unit test – Very high speed integrated circuit Hardware Description Language (VHDL) test and modified condition decision coverage (MC/DC) test, module test – MATLAB/Simulink Co-simulation test, and integration test – FPGA hardware test beds. To prove the adequacy of the proposed

Integrating Safety and Mission Assurance into Systems Engineering Modeling Practices

Science.gov (United States)

Beckman, Sean; Darpel, Scott

2015-01-01

During the early development of products, flight, or experimental hardware, emphasis is often given to the identification of technical requirements, utilizing such tools as use case and activity diagrams. Designers and project teams focus on understanding physical and performance demands and challenges. It is typically only later, during the evaluation of preliminary designs that a first pass, if performed, is made to determine the process, safety, and mission quality assurance requirements. Evaluation early in the life cycle, though, can yield requirements that force a fundamental change in design. This paper discusses an alternate paradigm for using the concepts of use case or activity diagrams to identify safety hazard and mission quality assurance risks and concerns using the same systems engineering modeling tools being used to identify technical requirements. It contains two examples of how this process might be used in the development of a space flight experiment, and the design of a Human Powered Pizza Delivery Vehicle, along with the potential benefits to decrease development time, and provide stronger budget estimates.

Multi-objective optimization of design and testing of safety instrumented systems with MooN voting architectures using a genetic algorithm

International Nuclear Information System (INIS)

Torres-Echeverría, A.C.; Martorell, S.; Thompson, H.A.

2012-01-01

This paper presents the optimization of design and test policies of safety instrumented systems using MooN voting redundancies by a multi-objective genetic algorithm. The objectives to optimize are the Average Probability of Dangerous Failure on Demand, which represents the system safety integrity, the Spurious Trip Rate and the Lifecycle Cost. In this way safety, reliability and cost are included. This is done by using novel models of time-dependent probability of failure on demand and spurious trip rate, recently published by the authors. These models are capable of delivering the level of modeling detail required by the standard IEC 61508. Modeling includes common cause failure and diagnostic coverage. The Probability of Failure on Demand model also permits to quantify results with changing testing strategies. The optimization is performed using the multi-objective Genetic Algorithm NSGA-II. This allows weighting of the trade-offs between the three objectives and, thus, implementation of safety systems that keep a good balance between safety, reliability and cost. The complete methodology is applied to two separate case studies, one for optimization of system design with redundancy allocation and component selection and another for optimization of testing policies. Both optimization cases are performed for both systems with MooN redundancies and systems with only parallel redundancies. Their results are compared, demonstrating how introducing MooN architectures presents a significant improvement for the optimization process.

Model checking of safety-critical software in the nuclear engineering domain

International Nuclear Information System (INIS)

Lahtinen, J.; Valkonen, J.; Björkman, K.; Frits, J.; Niemelä, I.; Heljanko, K.

2012-01-01

Instrumentation and control (I and C) systems play a vital role in the operation of safety-critical processes. Digital programmable logic controllers (PLC) enable sophisticated control tasks which sets high requirements for system validation and verification methods. Testing and simulation have an important role in the overall verification of a system but are not suitable for comprehensive evaluation because only a limited number of system behaviors can be analyzed due to time limitations. Testing is also performed too late in the development lifecycle and thus the correction of design errors is expensive. This paper discusses the role of formal methods in software development in the area of nuclear engineering. It puts forward model checking, a computer-aided formal method for verifying the correctness of a system design model, as a promising approach to system verification. The main contribution of the paper is the development of systematic methodology for modeling safety critical systems in the nuclear domain. Two case studies are reviewed, in which we have found errors that were previously not detected. We also discuss the actions that should be taken in order to increase confidence in the model checking process.

Safety-barrier diagrams as a tool for modelling safety of hydrogen applications

DEFF Research Database (Denmark)

Duijm, Nijs Jan; Markert, Frank

2009-01-01

Safety-barrier diagrams have proven to be a useful tool in documenting the safety measures taken to prevent incidents and accidents in process industry. Especially during the introduction of new hydrogen technologies or applications, as e.g. hydrogen refuelling stations, safety-barrier diagrams...... are considered a valuable supplement to other traditional risk analysis tools to support the communication with authorities and other stakeholders during the permitting process. Another advantage of safety-barrier diagrams is that they highlight the importance of functional and reliable safety barriers in any...... system and here is a direct focus on those barriers that need to be subject to safety management in terms of design and installation, operational use, inspection and monitoring, and maintenance. Safety-barrier diagrams support both quantitative and qualitative approaches. The paper will describe...

Seismic design and performance of nuclear safety related RC structures based on new seismic design principle

International Nuclear Information System (INIS)

Murugan, R.; Sivathanu Pillai, C.; Chattopadhyaya, S.; Sundaramurthy, C.

2011-01-01

Full text: Seismic design of safety related Reinforced Concrete (RC) structures of Nuclear power plants (NPP) in India as per the present AERB codal procedures tries to ensure predominantly elastic behaviour under OBE so that the features of Nuclear Power Plant (NPP) necessary for continued safe operation are designed to remain functional and prevent accident (collapse) of NPP under SSE for which certain Structures, Systems and Components (SSCs) those are necessary to ensure the capability to shut down the reactor safely, are designed to remain functional. While the seismic design principles of non safety related structures as per Indian code (IS 1893-2002) are ensuring elastic behaviour under DBE and inelastic behaviour under MCE by utilizing ductility and energy dissipation capacity of the structure effectively. The design principle of AERB code is ensuring elastic behaviour under OBE and is not enlightening much inference about the overall structural behaviour under SSE (only ensuring the capability of certain SSCs required for safe shutdown of reactor). Various buildings and structures of Indian Nuclear power plant are classified from the basis of associated safety functions in a descending order in according with their roles in preventions and mitigation of an accident or support functions for prevention. This paper covers a comprehensive seismic analysis and design methodology based on the AERB codal provisions followed for safety related RC structure taking Diesel Generator Building of PFBR as a case study and study and investigates its performance under OBE and SSE by carrying out Non-linear static Pushover analysis. Based on the analysis, observed variations, recommendations are given for getting the desired performance level so as to implement performance based design in the future NPP design

Design, fabrication and erection of steel structures important to safety of nuclear facilities

International Nuclear Information System (INIS)

2001-10-01

Civil engineering structures in nuclear installations form an important feature having implications to safety performance of these installations. The objective and minimum requirements for the design of civil engineering buildings/structures to be fulfilled to provide adequate assurance for safety of nuclear installations in India (such as pressurised heavy water reactor and related systems) are specified in the Safety Standard for Civil Engineering Structures Important to Safety of Nuclear Facilities. This standard is written by AERB to specify guidelines for implementation of the above civil engineering safety standard in the design, fabrication and erection of steel structures important to safety

Evaluating Models of Human Performance: Safety-Critical Systems Applications

Science.gov (United States)

Feary, Michael S.

2012-01-01

This presentation is part of panel discussion on Evaluating Models of Human Performance. The purpose of this panel is to discuss the increasing use of models in the world today and specifically focus on how to describe and evaluate models of human performance. My presentation will focus on discussions of generating distributions of performance, and the evaluation of different strategies for humans performing tasks with mixed initiative (Human-Automation) systems. I will also discuss issues with how to provide Human Performance modeling data to support decisions on acceptability and tradeoffs in the design of safety critical systems. I will conclude with challenges for the future.

Criticality safety and facility design considerations

International Nuclear Information System (INIS)

Waltz, W.R.

1991-06-01

Operations with fissile material introduce the risk of a criticality accident that may be lethal to nearby personnel. In addition, concerns over criticality safety can result in substantial delays and shutdown of facility operations. For these reasons, it is clear that the prevention of a nuclear criticality accident should play a major role in the design of a nuclear facility. The emphasis of this report will be placed on engineering design considerations in the prevention of criticality. The discussion will not include other important aspects, such as the physics of calculating limits nor criticality alarm systems

Time series modeling in traffic safety research.

Science.gov (United States)

Lavrenz, Steven M; Vlahogianni, Eleni I; Gkritza, Konstantina; Ke, Yue

2018-08-01

The use of statistical models for analyzing traffic safety (crash) data has been well-established. However, time series techniques have traditionally been underrepresented in the corresponding literature, due to challenges in data collection, along with a limited knowledge of proper methodology. In recent years, new types of high-resolution traffic safety data, especially in measuring driver behavior, have made time series modeling techniques an increasingly salient topic of study. Yet there remains a dearth of information to guide analysts in their use. This paper provides an overview of the state of the art in using time series models in traffic safety research, and discusses some of the fundamental techniques and considerations in classic time series modeling. It also presents ongoing and future opportunities for expanding the use of time series models, and explores newer modeling techniques, including computational intelligence models, which hold promise in effectively handling ever-larger data sets. The information contained herein is meant to guide safety researchers in understanding this broad area of transportation data analysis, and provide a framework for understanding safety trends that can influence policy-making. Copyright © 2017 Elsevier Ltd. All rights reserved.

Advanced nuclear reactor safety design technology research in NPIC

International Nuclear Information System (INIS)

Yu, H.

2014-01-01

After the Fukushima accident happen, Nuclear Power Plants (NPPs) construction has been suspended in China for a time. Now the new regulatory rule has been proposed that the most advanced safety standard must be adopted for the new NPPs and practical elimination of large fission product release by design during the next five plans period. So the advanced reactor research is developing in China. NPIC is engaging on the ACP1000 and ACP100 (Small Module Reactor) design. The main design character will be introduced in this paper. The Passive Combined with Active (PCWA) design was adopted during the ACP1000 design to reduce the core damage frequency (CDF); the Cavity Injection System (CIS) is design to mitigation the consequence of the severe accident. Advance passive safety system was designed to ensure the long term residual heat removal during the Small Module Reactor (SMR). The SMR will be utilized to be the floating reactors, district heating reactor and so on. Besides, the Science and Technology on Reactor System Design Technology Laboratory (LRSDT) also engaged on the fundamental thermal-hydraulic characteristic research in support of the system validation. (author)

Progress in design, research and development and testing of safety systems for advanced water cooled reactors. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

1996-04-01

The meeting covered the following topics: Developments in design of safety-related heat removal components and systems for advanced water cooled reactors; status of test programmes on heat removal components and systems of new designs; range of validity and extrapolation of test results for the qualification of design/licensing computer models and codes for advanced water cooled reactors; future needs and trends in testing of safety systems for advanced water cooled reactors. Tests of heat removal safety systems have been conducted by various groups supporting the design, testing and certification of advanced water cooled reactors. The Technical Committee concluded that the reported test results generally confirm the predicted performance features of the advanced designs. Refs, figs, tabs

Progress in design, research and development and testing of safety systems for advanced water cooled reactors. Proceedings of a technical committee meeting

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

The meeting covered the following topics: Developments in design of safety-related heat removal components and systems for advanced water cooled reactors; status of test programmes on heat removal components and systems of new designs; range of validity and extrapolation of test results for the qualification of design/licensing computer models and codes for advanced water cooled reactors; future needs and trends in testing of safety systems for advanced water cooled reactors. Tests of heat removal safety systems have been conducted by various groups supporting the design, testing and certification of advanced water cooled reactors. The Technical Committee concluded that the reported test results generally confirm the predicted performance features of the advanced designs. Refs, figs, tabs.

mathematical models for prediction of safety factors for a simply

African Journals Online (AJOL)

HOD

Keywords: reliability, code calibration, load factor, safety factor, design, steel beam. 1. INTRODUCTION ... safety factors for the design of a simply supported steel beam using regression .... 5 design criteria for a solid timber portal frame.

A series of student design projects for improving and modernizing safety helmets

NARCIS (Netherlands)

Beurden, van K.M.M. (Karin); Boer, de J. (Johannes); Stilma, M. (Margot); Teeuw, W.B. (Wouter)

2014-01-01

The Saxion Research Centre for Design and Technology employs many students during research projects. This paper discusses a series of student design projects on safety helmets in the Safety@Work project. At construction sites workers are required to wear personal protective equipment during their

Advanced analysis and design for fire safety of steel structures

CERN Document Server

Li, Guoqiang

2013-01-01

Advanced Analysis and Design for Fire Safety of Steel Structures systematically presents the latest findings on behaviours of steel structural components in a fire, such as the catenary actions of restrained steel beams, the design methods for restrained steel columns, and the membrane actions of concrete floor slabs with steel decks. Using a systematic description of structural fire safety engineering principles, the authors illustrate the important difference between behaviours of an isolated structural element and the restrained component in a complete structure under fire conditions. The book will be an essential resource for structural engineers who wish to improve their understanding of steel buildings exposed to fires. It is also an ideal textbook for introductory courses in fire safety for master’s degree programs in structural engineering, and is excellent reading material for final-year undergraduate students in civil engineering and fire safety engineering. Furthermore, it successfully bridges th...

A new safety approach in the design of fast reactors

International Nuclear Information System (INIS)

Neuhold, R.J.; Marchaterre, J.F.; Waltar, A.E.

1987-01-01

A new approach to achieving fast reactor safety goals is becoming really apparent in the US Fast Reactor Program. Whereas the ''defense is best'' philosophy still prevails, there has been a tangible shift toward emphasizing passive mechanisms to protect the reactor and provide public safety---rather than relying on add-on active, engineered safety systems. This paper reviews the technical basis for this new safety approach and provides discussion on its implementation in current US liquid metal-cooled reactor designs. 4 refs., 4 figs

Safety considerations and countermeasures against fire and explosion at an HTGR-hydrogen production system. Proposal of safety design concept

International Nuclear Information System (INIS)

Nishihara, T.; Hada, K.; Shibata, T.; Shiozawa, S.

1996-01-01

Establishment of safety design concept and countermeasures against fire and explosion accidents is among key safety-related issues in an HTGR-hydrogen production system. We propose the different safety design concepts depending upon the origin of fire and explosion which may happen in the HTGR-hydrogen production plant. Against fire and explosion originated outside the reactor building (R/B), namely in the area of hydrogen production plant, the safety design concept is primarily to take a safe distance for preventing the damage on safety-related items or a proof wall if necessary. Because the hydrogen production plant is designed in the same safety level as a conventional chemical plant. The safe distance is proposed to limit an incident overpressure to 10 kPa so as not to suffer any damage on the items and to limit a wall-averaged temperature of concrete structures of the R/B to 175degC according to the current regulation. On the other hand, against a potential possibility of explosion originated inside the R/B, the safety design concept is to minimize the possibility of explosion low enough to assume no occurrence inside the R/B. That is, the measure is to exclude a simultaneous failure of a secondary helium piping and an endothermic chemical reactor. Furthermore, in severe accident condition in which the explosion may be postulated a priori, an incidental overpressure of explosion inside the reactor containment vessel (C/V) should be limited so as not to fail the C/V through restricting the amount of combustible gas ingress into the C/V by means of a combination of C/V isolation valve installed in the helium piping and emergency shut off valve in the process feed gas line. (author)

Occupational health and safety: Designing and building with MACBETH a value risk-matrix for evaluating health and safety risks

Science.gov (United States)

Lopes, D. F.; Oliveira, M. D.; Costa, C. A. Bana e.

2015-05-01

Risk matrices (RMs) are commonly used to evaluate health and safety risks. Nonetheless, they violate some theoretical principles that compromise their feasibility and use. This study describes how multiple criteria decision analysis methods have been used to improve the design and the deployment of RMs to evaluate health and safety risks at the Occupational Health and Safety Unit (OHSU) of the Regional Health Administration of Lisbon and Tagus Valley. ‘Value risk-matrices’ (VRMs) are built with the MACBETH approach in four modelling steps: a) structuring risk impacts, involving the construction of descriptors of impact that link risk events with health impacts and are informed by scientific evidence; b) generating a value measurement scale of risk impacts, by applying the MACBETH-Choquet procedure; c) building a system for eliciting subjective probabilities that makes use of a numerical probability scale that was constructed with MACBETH qualitative judgments on likelihood; d) and defining a classification colouring scheme for the VRM. A VRM built with OHSU members was implemented in a decision support system which will be used by OHSU members to evaluate health and safety risks and to identify risk mitigation actions.

Plasma-safety assessment model and safety analyses of ITER

International Nuclear Information System (INIS)

Honda, T.; Okazaki, T.; Bartels, H.-H.; Uckan, N.A.; Sugihara, M.; Seki, Y.

2001-01-01

A plasma-safety assessment model has been provided on the basis of the plasma physics database of the International Thermonuclear Experimental Reactor (ITER) to analyze events including plasma behavior. The model was implemented in a safety analysis code (SAFALY), which consists of a 0-D dynamic plasma model and a 1-D thermal behavior model of the in-vessel components. Unusual plasma events of ITER, e.g., overfueling, were calculated using the code and plasma burning is found to be self-bounded by operation limits or passively shut down due to impurity ingress from overheated divertor targets. Sudden transition of divertor plasma might lead to failure of the divertor target because of a sharp increase of the heat flux. However, the effects of the aggravating failure can be safely handled by the confinement boundaries. (author)

A proposal for safety design philosophy of HTGR for coupling hydrogen production plant

International Nuclear Information System (INIS)

Sato, Hiroyuki; Ohashi, Hirofumi; Tazawa, Yujiro; Imai, Yoshiyuki; Nakagawa, Shigeaki; Tachibana, Yukio; Kunitomi, Kazuhiko

2013-06-01

Japan Atomic Energy Agency (JAEA) has been conducting research and development for hydrogen production utilizing heat from High Temperature Gas-cooled Reactors (HTGRs). Towards the realization of nuclear hydrogen production, coupled hydrogen production plants should not be treated as an extension of a nuclear plant in order to open the door for the entry of non-nuclear industries as well as assuring reactor safety against postulated abnormal events initiated in the hydrogen production plants. Since hydrogen production plant utilizing nuclear heat has never been built in the world, little attention has been given to the establishment of a safety design for such system including the High Temperature engineering Test Reactor (HTTR). In the present study, requirements in order to design, construct and operate hydrogen production plants under conventional chemical plant standards are identified. In addition, design considerations for safety design of nuclear facility are suggested. Furthermore, feasibility of proposed safety design and design considerations are evaluated. (author)

Modelling and simulation in nuclear safety and the role of experiment

International Nuclear Information System (INIS)

Baek, W-P.

2015-01-01

'Full text:' Modeling and simulation (M&S) technology is a key element in assuring and enhancing the safety of nuclear installations. The M&S technology has been progressed continuously with the introduction of new designs, improved understanding on relevant physical processes, and the improvement of computing environment. This presentation covers the role, progresses and prospect of M&S technology relevant to nuclear safety. Special attention is given to the effective interaction between M&S and experiment. The expected role of experiment to motivate the advancement of M&S technology is emphasized with some typical examples. Finally, relevant R&D activities of Korea are introduced for thermal-hydraulics and severe accident safety. (author)

Design of Vertical Wall Caisson Breakwaters using Partial Safety Factors

DEFF Research Database (Denmark)

Burcharth, H. F.; Sørensen, John Dalsgaard

1999-01-01

The paper presents a new system for implementation of target reliability in caisson breakwater designs by means of partial safety factors. The development of the system is explained, and tables of partial safety factors are presented for important overall stability failure modes related to caisson...

Nuclear safety culture evaluation model based on SSE-CMM

International Nuclear Information System (INIS)

Yang Xiaohua; Liu Zhenghai; Liu Zhiming; Wan Yaping; Peng Guojian

2012-01-01

Safety culture, which is of great significance to establish safety objectives, characterizes level of enterprise safety production and development. Traditional safety culture evaluation models emphasis on thinking and behavior of individual and organization, and pay attention to evaluation results while ignore process. Moreover, determining evaluation indicators lacks objective evidence. A novel multidimensional safety culture evaluation model, which has scientific and completeness, is addressed by building an preliminary mapping between safety culture and SSE-CMM's (Systems Security Engineering Capability Maturity Model) process area and generic practice. The model focuses on enterprise system security engineering process evaluation and provides new ideas and scientific evidences for the study of safety culture. (authors)

Safety Design Strategy for the Advanced Test Reactor Emergency Firewater Injection System Replacement Project

International Nuclear Information System (INIS)

Duckwitz, Noel

2011-01-01

In accordance with the requirements of U.S. Department of Energy (DOE) Order 413.3B, 'Program and Project Management for the Acquisition of Capital Assets,' safety must be integrated into the design process for new or major modifications to DOE Hazard Category 1, 2, and 3 nuclear facilities. The intended purpose of this requirement involves the handling of hazardous materials, both radiological and chemical, in a way that provides adequate protection to the public, workers, and the environment. Requirements provided in DOE Order 413.3B and DOE Order 420.1B, 'Facility Safety,' and the expectations of DOE-STD-1189-2008, 'Integration of Safety into the Design Process,' provide for identification of hazards early in the project and use of an integrated team approach to design safety into the facility. This safety design strategy provides the basic safety-in-design principles and concepts that will be used for the Advanced Test Reactor Reliability Sustainment Project. While this project does not introduce new hazards to the ATR, it has the potential for significant impacts to safety-related systems, structures, and components that are credited in the ATR safety basis and are being replaced. Thus the project has been determined to meet the definition of a major modification and is being managed accordingly.

Analysis of effect of safety classification on DCS design in nuclear power plants

International Nuclear Information System (INIS)

Gou Guokai; Li Guomin; Wang Qunfeng

2011-01-01

By analyzing the safety classification for the systems and functions of nuclear power plants based on the general design requirements for nuclear power plants, especially the requirement of availability and reliability of I and C systems, the characteristics of modem DCS technology and I and C products currently applied in nuclear power field are interpreted. According to the requirements on the safety operation of nuclear power plants and the regulations for safety audit, the effect of different safety classifications on DCS design in nuclear power plants is analyzed, by considering the actual design process of different DCS solutions in the nuclear power plants under construction. (authors)

IEEE standard for design qualification of safety systems equipment used in nuclear power generating stations

International Nuclear Information System (INIS)

Anon.

1980-01-01

This standard is written to serve as a general standard for qualification of all types of safety systems equipment, mechanical and instrumentation as well as electrical. It also establishes principles and procedures to be followed in preparing specific safety systems equipment standards. Guidance for qualifying specific safety systems equipment may be found in various specific equipment qualification standards that are now available or are being prepared. It is required that safety systems equipment in nuclear power generating stations meet or exceed its performance requirements throughout its installed life. This is accomplished by a disciplined program of design qualification and quality assurance of design, production, installation, maintenance and surveillance. This standard is for the design qualification section of the program only. Design qualification is intended to demonstrate the capability of the equipment design to perform its safety function(s) over the expected range of normal, abnormal, design basis event, post design basis event, and in-service test conditions. Inherent to design qualification is the requirement for demonstration, within limitations afforded by established technical state-of-the-art, that in-service aging throughout the qualified life established for the equipment will not degrade safety systems equipment from its original design condition to the point where it cannot perform its required safety function(s), upon demand. The above requirement reflects the primary role of design qualification to provide reasonable assurance that design- and age-related common failure modes will not occur during performance of safety function(s) under postulated service conditions

[Design, implementation and evaluation of a management model of patient safety in hospitals in Catalonia, Spain].

Science.gov (United States)

Saura, Rosa Maria; Moreno, Pilar; Vallejo, Paula; Oliva, Glòria; Alava, Fernando; Esquerra, Miquel; Davins, Josep; Vallès, Roser; Bañeres, Joaquim

2014-07-01

Since its inception in 2006, the Alliance for Patient Safety in Catalonia has played a major role in promoting and shaping a series of projects related to the strategy of the Ministry of Health, Social Services and Equality, for improving patient safety. One such project was the creation of functional units or committees of safety in hospitals in order to facilitate the management of patient safety. The strategy has been implemented in hospitals in Catalonia which were selected based on criteria of representativeness. The intervention was based on two lines of action, one to develop the model framework and the other for its development. Firstly the strategy for safety management based on EFQM (European Foundation for Quality Management) was defined with the development of standards, targets and indicators to implement security while the second part involved the introduction of tools, methodologies and knowledge to the management support of patient safety and risk prevention. The project was developed in four hospital areas considered higher risk, each assuming six goals for safety management. Some of these targets such as the security control panel or system of adverse event reporting were shared. 23 hospitals joined the project in Catalonia. Despite the different situations in each centre, high compliance was achieved in the development of the objectives. In each of the participating areas the security control panel was developed. Stable structures for safety management were established or strengthened. Training in patient safety played and important role, 1415 professionals participated. Through these kind of projects not only have been introduced programs of proven effectiveness in reducing risks, but they also provide to the facilities a work system that allows autonomy in diagnosis and analysis of the different risk situations or centre specific safety issues. Copyright © 2014. Published by Elsevier Espana.

Experimental Study and Computational Simulations of Key Pebble Bed Thermo-mechanics Issues for Design and Safety

Energy Technology Data Exchange (ETDEWEB)

Tokuhiro, Akira; Potirniche, Gabriel; Cogliati, Joshua; Ougouag, Abderrafi

2014-07-08

An experimental and computational study, consisting of modeling and simulation (M&S), of key thermal-mechanical issues affecting the design and safety of pebble-bed (PB) reactors was conducted. The objective was to broaden understanding and experimentally validate thermal-mechanic phenomena of nuclear grade graphite, specifically, spheres in frictional contact as anticipated in the bed under reactor relevant pressures and temperatures. The contact generates graphite dust particulates that can subsequently be transported into the flowing gaseous coolent. Under postulated depressurization transients and with the potential for leaked fission products to be adsorbed onto graphite 'dust', there is the potential for fission products to escape from the primary volume. This is a design safety concern. Furthermore, earlier safety assessment identified the distinct possibility for the dispersed dust to combust in contact with air if sufficient conditions are met. Both of these phenomena were noted as important to design review and containing uncertainty to warrant study. The team designed and conducted two separate effects tests to study and benchmark the potential dust-generation rate, as well as study the conditions under which a dust explosion may occure in a standardized, instrumented explosion chamber.

Basic concept of fuel safety design and assessment for sodium-cooled fast reactor

International Nuclear Information System (INIS)

Nakae, Nobuo; Baba, Toshikazu; Kamimura, Katsuichiro

2013-03-01

'Philosophy in Safety Evaluation of Fast Breeder Reactors' was published as a guideline for safety design and safety evaluation of Sodium-Cooled Fast Reactor in Japan. This guideline points out that cladding creep and swelling due to internal pressure should be taken into account since the fuel is used under high temperature and high burnup, and that fuel assembly deformation and the prevention from coolant channel blockage should be taken into account in viewpoints of nuclear and thermal hydraulic design. However, the requirements including their criteria and evaluation items are not described. Two other domestic guidelines related to core design are applied for fuel design of fast reactor, but the description is considered to not be enough to practically use. In addition, technical standard for nuclear fuel used in power reactors is also applied for fuel inspection. Therefore, the technical standard and guideline for fuel design and safety evaluation are considered to be very important issue for nuclear safety regulation. This document has been developed according to the following steps: The guidelines and the technical standards, which are prepared in foreign countries and international organization, were reviewed. The technical background concerning fuel design and safety evaluation for fast reactor was collected and summarized in the world wide scale. The basic concept of fuel safety design and assessment for sodium-cooled fast reactor was developed by considering a wide range of views of the specialists in Japan. In order to discuss the content with foreign specialists IAEA Consultancy Meetings have been held on January, 2011 and January, 2012. The participants of the meeting came from USA, UK, EC, India, China and South Korea. The specialists of IAEA and JNES were also joined. Although this document is prepared for application to 'Monju'(prototype LMFR), it may be applied to experimental, demonstration and commercial types of LMFR after revising it by taking

Use of safety experience feedback to design new nuclear units

International Nuclear Information System (INIS)

Lange, D.; Crochon, J.P.

1985-06-01

For the designer, and about safety, the experience feedback can take place in 3 fields: the operating experience feedback (incidents analysis), the ''study'' experience feedback (improvement of justification and evolution of safety considerations), and the fabrication experience feedback. Some examples are presented for each field [fr

Safety and environmental aspects of the HYLIFE-II and ARIES fusion reactor designs

International Nuclear Information System (INIS)

Dolan, T.J.; Longhurst, G.R.; Herring, J.S.

1993-01-01

The HYLIFE-II inertial confinement fusion reactor design uses jets of Flibe molten salt to protect the blast chamber walls and to breed tritium. It has a low tritium inventory and effective tritium removal. The issue with this design is not one of safety but of economics. The ARIES reactor designs have safety concerns associated with fires. These reactors designs are described

Safety Evaluation of Kartini Reactor Based on Instrumentation System Design

International Nuclear Information System (INIS)

Tjipta Suhaemi; Djen Djen Dj; Itjeu K; Johnny S; Setyono

2003-01-01

The safety of Kartini reactor has been evaluated based on instrumentation system aspect. The Kartini reactor is designed by BATAN. Design power of the reactor is 250 kW, but it is currently operated at 100 kW. Instrumentation and control system function is to monitor and control the reactor operation. Instrumentation and control system consists of safety system, start-up and automatic power control, and process information system. The linear power channel and logarithmic power channel are used for measuring power. There are 3 types of control rod for controlling the power, i.e. safety rod, shim rod, and regulating rod. The trip and interlock system are used for safety. There are instrumentation equipment used for measuring radiation exposure, flow rate, temperature and conductivity of fluid The system of Kartini reactor has been developed by introducing a process information system, start-up system, and automatic power control. It is concluded that the instrumentation of Kartini reactor has followed the requirement and standard of IAEA. (author)

Design and reliability, availability, maintainability, and safety analysis of a high availability quadruple vital computer system

Institute of Scientific and Technical Information of China (English)

Ping TAN; Wei-ting HE; Jia LIN; Hong-ming ZHAO; Jian CHU

2011-01-01

With the development of high-speed railways in China,more than 2000 high-speed trains will be put into use.Safety and efficiency of railway transportation is increasingly important.We have designed a high availability quadruple vital computer (HAQVC) system based on the analysis of the architecture of the traditional double 2-out-of-2 system and 2-out-of-3 system.The HAQVC system is a system with high availability and safety,with prominent characteristics such as fire-new internal architecture,high efficiency,reliable data interaction mechanism,and operation state change mechanism.The hardware of the vital CPU is based on ARM7 with the real-time embedded safe operation system (ES-OS).The Markov modeling method is designed to evaluate the reliability,availability,maintainability,and safety (RAMS) of the system.In this paper,we demonstrate that the HAQVC system is more reliable than the all voting triple modular redundancy (AVTMR) system and double 2-out-of-2 system.Thus,the design can be used for a specific application system,such as an airplane or high-speed railway system.

Safety instrumented systems in the oil and gas industry : Concepts and methods for safety and reliability assessments in design and operation

Energy Technology Data Exchange (ETDEWEB)

Lundteigen, Mary Ann

2009-07-01

This thesis proposes new methods and gives new insight to safety and reliability assessments of safety instrumented systems (SISs). These systems play an important role in many industry sectors and are used to detect the onset of hazardous events and mitigate their consequences to humans, the environment, and material assets. The thesis focuses on SIS applications in the oil and gas industry. Here, the SIS must respond to hazardous events such as gas leakages, fires, and over pressurization. Because there are personnel onboard the oil and gas installations, the operations take place in a vulnerable marine environment, and substantial values are associated with the offshore facilities, the reliability of SIS is of great concern to the public, the authorities, and the plant owners. The objective of this project has been to identify some of the key factors that influence the SIS reliability, clarify their effects on reliability, and suggest means to improve the treatment of these factors in safety and reliability assessments in design and operation. The project builds on concepts, methods, and definitions in two key standards for SIS design, construction, and operation: IEC 61508 and IEC 61511. The main contributions from this project are: A product development model that integrates reliability, availability, maintainability, and safety (RAMS) requirements with product development. The contributions have been presented in ten articles, five published in international journals, two submitted for publication, and three presented at conferences and in conference proceedings. The contributions are also directed to the industry and the actors that are involved in SIS design, construction, and operation. Even if the oil and gas industry is the main focus area, the results may be relevant for other industry sectors as well. SIS manufacturers and SIS designers face a large number of requirements from authorities, oil companies, international standards, and so on. At the same

Safety Cultural Competency Modeling in Nuclear Organizations

Energy Technology Data Exchange (ETDEWEB)

Kim, Sa Kil; Oh, Yeon Ju; Luo, Meiling; Lee, Yong Hee [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

The nuclear safety cultural competency model should be supplemented through a bottom-up approach such as behavioral event interview. The developed model, however, is meaningful for determining what should be dealt for enhancing safety cultural competency of nuclear organizations. The more details of the developing process, results, and applications will be introduced later. Organizational culture include safety culture in terms of its organizational characteristics.

Impact of ITER liquid metal design options on safety level and licensing - Sweden

International Nuclear Information System (INIS)

Harfors, C.; Devell, L.; Johansson, Kjell; Lundell, B.; Rolandsson, S.

1993-01-01

The safety level and licensability of five design options for ITER coolant, breeding material and structural material are assessed, with emphasis on some specified accident scenarios. The safety level is assessed in terms of barrier requirements and the feasibility to construct and qualify such a barrier. The licensability in Sweden of each design option is assessed based on the indicated safety level and on a judgement of the technical feasibility to construct and qualify the ITER tokamak itself, based on the selected design option. 20 refs

JSFR design progress related to development of safety design criteria for generation IV sodium-cooled fast reactors. (3) Progress of component design

International Nuclear Information System (INIS)

Enuma, Yasuhiro; Kawasaki, Nobuchika; Orita, Junichi; Eto, Masao; Miyagawa, Takayuki

2015-01-01

In the frame work of generation IV international forum (GIF), safety design criteria (SDC) and safety design guideline (SDG) for the generation IV sodium-cooled fast reactors have been developing in the circumstance of worldwide deployment of SFRs. JAEA, JAPC, MFBR have been investigating design study for JSFR to satisfy SDC in the feasibility study of SDG for Sodium-cooled Fast Reactor (SFR). In addition to the safety measures, maintainability, reparability and manufacturability are taken into account in the JSFR design study. This paper describes the design of main components. Enlargement of the access route for the inspection devices and addition of the access routes were carried out for the reactor structure. The pump-integrated IHX (pump/IHX) was modified for the primary heat exchanger (PHX), which was installed for the decay heat removal in the IHX at the upper plenum, to be removable for improved repair and maintenance. For the steam generator (SG), protective wall tube type design is under investigation as an option with less R and D risks. (author)

Assistance for design and realization of real-time safety critical applications according to Oasis

International Nuclear Information System (INIS)

Aussagues, Ch.; Cordonnier, Ch.; Quetueil, I.; David, V.

1998-01-01

Assistance for design and realization is all the more essential when safety-critical, real-time and complex applications are considered. When developing such applications, real-time and dependability features should be managed as soon as possible. Then, since the design phase, programmers have to strive even more than with common applications. In the context of the OASIS approach, assistance for design and realization is based on some intrinsic properties of the model, i.e. determinism, behavior independence and timeliness. The assistance, that may be furnished in the OASIS approach, has three complementary components that constitute the focus of this article. (authors)

Decomobil, Deliverable 3.6, Human Centred Design for Safety Critical Transport Systems

OpenAIRE

PAUZIE, Annie; MENDOZA, Lucile; SIMOES, Anabela; BELLET, Thierry; MOREAU, Fabien

2014-01-01

The scientific seminar on 'Human Centred Design for Safety Critical Transport Systems' organized in the framework of DECOMOBIL has been held the 8th of September 2014 in Lisbon, Portugal, hosted by ADI/ISG. The aims of the event were to present the scientific problematic related to the safety of the complex transport systems and the increasing importance of human-­centred design, with a specific focus on Resilience Engineering concept, a new approach to safety management in highly complex sys...

The spread model of food safety risk under the supply-demand disturbance

OpenAIRE

Wang, Jining; Chen, Tingqiang

2016-01-01

In this paper, based on the imbalance of the supply-demand relationship of food, we design a spreading model of food safety risk, which is about from food producers to consumers in the food supply chain. We use theoretical analysis and numerical simulation to describe the supply-demand relationship and government supervision behaviors? influence on the risk spread of food safety and the behaviors of the food producers and the food retailers. We also analyze the influence of the awareness of c...

Pressurized water reactor system model for control system design and analysis

International Nuclear Information System (INIS)

Cooper, K.F.; Cain, J.T.

1975-01-01

Satisfactory operation of present generation Pressurized Water Reactor (PWR) Nuclear Power systems requires that several independent and interactive control systems be designed. Since it is not practical to use an actual PWR system as a design tool, a mathematical model of the system must be developed as a design and analysis tool. The model presented has been developed to be used as an aid in applying optimal control theory to design and implement new control systems for PWR plants. To be applicable, the model developed must represent the PWR system in its normal operating range. For safety analysis the operating conditions of the system are usually abnormal and, therefore, the system modeling requirements are different from those for control system design and analysis

Developing a model for hospital inherent safety assessment: Conceptualization and validation.

Science.gov (United States)

Yari, Saeed; Akbari, Hesam; Gholami Fesharaki, Mohammad; Khosravizadeh, Omid; Ghasemi, Mohammad; Barsam, Yalda; Akbari, Hamed

2018-01-01

Paying attention to the safety of hospitals, as the most crucial institute for providing medical and health services wherein a bundle of facilities, equipment, and human resource exist, is of significant importance. The present research aims at developing a model for assessing hospitals' safety based on principles of inherent safety design. Face validity (30 experts), content validity (20 experts), construct validity (268 examples), convergent validity, and divergent validity have been employed to validate the prepared questionnaire; and the items analysis, the Cronbach's alpha test, ICC test (to measure reliability of the test), composite reliability coefficient have been used to measure primary reliability. The relationship between variables and factors has been confirmed at 0.05 significance level by conducting confirmatory factor analysis (CFA) and structural equations modeling (SEM) technique with the use of Smart-PLS. R-square and load factors values, which were higher than 0.67 and 0.300 respectively, indicated the strong fit. Moderation (0.970), simplification (0.959), substitution (0.943), and minimization (0.5008) have had the most weights in determining the inherent safety of hospital respectively. Moderation, simplification, and substitution, among the other dimensions, have more weight on the inherent safety, while minimization has the less weight, which could be due do its definition as to minimize the risk.

An Axiomatic Design Approach of Nanofluid-Engineered Nuclear Safety Features for Generation III+ React

International Nuclear Information System (INIS)

Bang, In Cheol; Heo, Gyun Young; Jeong, Yong Hoon; Heo, Sun

2009-01-01

A variety of Generation III/III+ reactor designs featuring enhanced safety and improved economics are being proposed by nuclear power industries around the world to solve the future energy supply shortfall. Nanofluid coolants showing an improved thermal performance are being considered as a new key technology to secure nuclear safety and economics. However, it should be noted that there is a lack of comprehensible design works to apply nanofluids to Generation III+ reactor designs. In this work, the review of accident scenarios that consider expected nanofluid mechanisms is carried out to seek detailed application spots. The Axiomatic Design (AD) theory is then applied to systemize the design of nanofluid-engineered nuclear safety systems such as Emergency Core Cooling System (ECCS) and External Reactor Vessel Cooling System (ERVCS). The various couplings between Gen-III/III+ nuclear safety features and nanofluids are investigated and they try to be reduced from the perspective of the AD in terms of prevention/mitigation of severe accidents. This study contributes to the establishment of a standard communication protocol in the design of nanofluid-engineered nuclear safety systems

An optimization model for improving highway safety

Directory of Open Access Journals (Sweden)

Promothes Saha

2016-12-01

Full Text Available This paper developed a traffic safety management system (TSMS for improving safety on county paved roads in Wyoming. TSMS is a strategic and systematic process to improve safety of roadway network. When funding is limited, it is important to identify the best combination of safety improvement projects to provide the most benefits to society in terms of crash reduction. The factors included in the proposed optimization model are annual safety budget, roadway inventory, roadway functional classification, historical crashes, safety improvement countermeasures, cost and crash reduction factors (CRFs associated with safety improvement countermeasures, and average daily traffics (ADTs. This paper demonstrated how the proposed model can identify the best combination of safety improvement projects to maximize the safety benefits in terms of reducing overall crash frequency. Although the proposed methodology was implemented on the county paved road network of Wyoming, it could be easily modified for potential implementation on the Wyoming state highway system. Other states can also benefit by implementing a similar program within their jurisdictions.

Design of the reactor coolant system and associated systems in nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2008-01-01

This Safety Guide was prepared under the IAEA programme for establishing safety standards for nuclear power plants. The basic requirements for the design of safety systems for nuclear power plants are established in the Safety Requirements publication, Safety Standards Series No. NS-R-1 on Safety of Nuclear Power Plants: Design, which it supplements. This Safety Guide describes how the requirements for the design of the reactor coolant system (RCS) and associated systems in nuclear power plants should be met. 1.2. This publication is a revision and combination of two previous Safety Guides, Safety Series No. 50-SG-D6 on Ultimate Heat Sink and Directly Associated Heat Transport Systems for Nuclear Power Plants (1981), and Safety Series No. 50-SG-D13 on Reactor Coolant and Associated Systems in Nuclear Power Plants (1986), which are superseded by this new Safety Guide. 1.3. The revision takes account of developments in the design of the RCS and associated systems in nuclear power plants since the earlier Safety Guides were published in 1981 and 1986, respectively. The other objectives of the revision are to ensure consistency with Ref., issued in 2000, and to update the technical content. In addition, an appendix on pressurized heavy water reactors (PHWRs) has been included

Research on Evaluation Model for Secondary Task Driving Safety Based on Driver Eye Movements

Directory of Open Access Journals (Sweden)

Lisheng Jin

2014-01-01

Full Text Available This study was designed to gain insight into the influence of performing different types of secondary task while driving on driver eye movements and to build a safety evaluation model for secondary task driving. Eighteen young drivers were selected and completed the driving experiment on a driving simulator. Measures of fixations, saccades, and blinks were analyzed. Based on measures which had significant difference between the baseline and secondary tasks driving conditions, the evaluation index system was built. Method of principal component analysis (PCA was applied to analyze evaluation indexes data in order to obtain the coefficient weights of indexes and build the safety evaluation model. Based on evaluation scores, the driving safety was grouped into five levels (very high, high, average, low, and very low using K-means clustering algorithm. Results showed that secondary task driving severely distracts the driver and the evaluation model built in this study could estimate driving safety effectively under different driving conditions.

A Review of Safety and Design Requirements of the Artificial Pancreas.

Science.gov (United States)

Blauw, Helga; Keith-Hynes, Patrick; Koops, Robin; DeVries, J Hans

2016-11-01

As clinical studies with artificial pancreas systems for automated blood glucose control in patients with type 1 diabetes move to unsupervised real-life settings, product development will be a focus of companies over the coming years. Directions or requirements regarding safety in the design of an artificial pancreas are, however, lacking. This review aims to provide an overview and discussion of safety and design requirements of the artificial pancreas. We performed a structured literature search based on three search components-type 1 diabetes, artificial pancreas, and safety or design-and extended the discussion with our own experiences in developing artificial pancreas systems. The main hazards of the artificial pancreas are over- and under-dosing of insulin and, in case of a bi-hormonal system, of glucagon or other hormones. For each component of an artificial pancreas and for the complete system we identified safety issues related to these hazards and proposed control measures. Prerequisites that enable the control algorithms to provide safe closed-loop control are accurate and reliable input of glucose values, assured hormone delivery and an efficient user interface. In addition, the system configuration has important implications for safety, as close cooperation and data exchange between the different components is essential.

Nuclear safety and radiation protection consideration in the design of research and development facility

International Nuclear Information System (INIS)

Akbar, M.R.

2010-01-01

Nuclear safety is a critically important aspect that must be considered in the design of a nuclear facility in order to ensure the protection of the workers, public and environment. This paper looks at the methodology, approach and incorporation of this aspect, specifically into the design of a research and development facility. The Health, Safety and Environmental Basis of Design is an initial analysis of nuclear safety and radiation protection considerations that is performed during the conceptual design phase and sets the baseline for what the design of the facility must conform to. It consists of general nuclear safety design principles, such as defence in depth and optimisation considerations, and a hazard management strategy. Following the Health, Safety and Environmental Basis of Design, a Preliminary Safety Assessment Report is generated during the basic design phase in conjunction with various analyses in order to assess the impact of hazards on the workers and members of the public. This assessment follows a hazard graded approach where the depth of the analysis will be determined by the impact of the worst case accident scenario in the facility. The assessment also includes a waste management strategy which is an essential aspect to be considered in the design in order to minimize the generation of waste. The safety assessment also demonstrates compliance to dose limits and risk criteria for the workers and members of the public set by the regulatory body and supported by a legal framework. Measures are taken to keep risk as low as reasonably achievable and prevent transgression of the risk and dose limits. However, a balance needs to be maintained between 5 reducing these doses further and the cost of such a reduction, which is known as optimization. It is therefore imperative to have nuclear safety specialists analyse the design in order to protect the worker and member of the public from unwarranted exposure to nuclear radiation. (author)

Design of nuclear power generation plants adopting model engineering method

International Nuclear Information System (INIS)

Waki, Masato

1983-01-01

The utilization of model engineering as the method of design has begun about ten years ago in nuclear power generation plants. By this method, the result of design can be confirmed three-dimensionally before actual production, and it is the quick and sure method to meet the various needs in design promptly. The adoption of models aims mainly at the improvement of the quality of design since the high safety is required for nuclear power plants in spite of the complex structure. The layout of nuclear power plants and piping design require the model engineering to arrange rationally enormous quantity of things in a limited period. As the method of model engineering, there are the use of check models and of design models, and recently, the latter method has been mainly taken. The procedure of manufacturing models and engineering is explained. After model engineering has been completed, the model information must be expressed in drawings, and the automation of this process has been attempted by various methods. The computer processing of design is in progress, and its role is explained (CAD system). (Kako, I.)

A fuzzy-based model to implement the global safety buildings index assessment for agri-food buildings

Directory of Open Access Journals (Sweden)

Francesco Barreca

2014-06-01

Full Text Available The latest EU policies focus on the issue of food safety with a view to ensuring adequate and standard quality levels for the food produced and/or consumed within the EC. To that purpose, the environment where agricultural products are manufactured and processed plays a crucial role in achieving food hygiene. As a consequence, it is of the outmost importance to adopt proper building solutions which meet health and hygiene requirements as well as to use suitable tools to measure the levels achieved. Similarly, it is necessary to verify and evaluate the level of workers’ safety and welfare in their working environment. Workers’ safety has not only an ethical and social value but also an economic implication, since possible accidents or environmental stressors are the major causes of the lower efficiency and productivity of workers. Therefore, it is fundamental to design suitable models of analysis that allow assessing buildings as a whole, taking into account both health and hygiene safety as well as workers’ safety and welfare. Hence, this paper proposes an assessment model that, based on an established study protocol and on the application of a fuzzy logic procedure, allows assessing the global safety level of an agri-food building by means of a global safety buildings index. The model here presented is original since it uses fuzzy logic to evaluate the performances of both the technical and environmental systems of an agri-food building in terms of health and hygiene safety of the manufacturing process as well as of workers’ health and safety. The result of the assessment is expressed through a triangular fuzzy membership function which allows carrying out comparative analyses of different buildings. A specific procedure was developed to apply the model to a case study which tested its operational simplicity and the validity of its results. The proposed model allows obtaining a synthetic and global value of the building performance of

Using a collision model to design safer wind turbine rotors for birds

International Nuclear Information System (INIS)

Tucker, V.A.

1996-01-01

A mathematical model for collisions between birds and propeller-type turbine rotors identifies the variables that can be manipulated to reduce the probability that birds will collide with the rotor. This study defines a safety index--the clearance power density--that allows rotors of different sizes and designs to be compared in terms of the amount of wind energy converted to electrical energy per bird collision. The collision model accounts for variations in wind speed during the year and shows that for model rotors with simple, one-dimensional blades, the safety index increases in proportion to rotor diameter, and variable speed rotors have higher safety indexes than constant speed rotors. The safety index can also be increased by enlarging the region near the center of the rotor hub where the blades move slowly enough for birds to avoid them. Painting the blades to make them more visible might have this effect. Model rotors with practical designs can have safety indexes an order of magnitude higher than those for model rotors typical of the constant speeds rotors in common use today. This finding suggests that redesigned rotors could have collision rates with birds perhaps an order of magnitude lower than today's rotors, with no reduction in the production of wind power. The empirical data that exist for collisions between raptors, such as hawks and eagles, and rotors are consistent with the model: the numbers of raptor carcasses found beneath large variable speed rotors, relative to the numbers found under small constant speed rotors, are in the proportions predicted by the collision model rather than in proportion to the areas swept by the rotor blades. However, uncontrolled variables associated with these data prevent a stronger claim of support for the model

Safety investigation of 'Mutsu', the first nuclear ship in Japan (the correspondence to the guideline of safety design examination, etc.)

International Nuclear Information System (INIS)

1981-01-01

Japan Nuclear Ship Development Agency had made previously application for the permission of the alteration of the reactor installation in the nuclear ship Mutsu (the first of this kind in Japan), based on the overall safety investigation of the ship made by JNDA. Taking the opportunity of the governmental safety examination concerning the permission, the correspondence of the safety aspects of the n.s. Mutsu to the existing guidelines for the safety of nuclear reactor facilities was examined. These results to further enhance the safety of the n.s. Mutsu are described concerning the following matters: the safety design examination guideline for power-generating LWR facilities (58 items); the safety evaluation guideline for power-generating LWR facilities (the analysis of abnormal transients during operation and accidents); the safety countermeasures to be adopted in the reactor plant of the n.s. Mutsu from the situation of the TMI nuclear accident in U.S. (7 in design and 10 in operation management); the analysis simulating the TMI accident. (J.P.N.)

Core design with respect to the safety concept

International Nuclear Information System (INIS)

Kollmar, W.

1981-01-01

In the present paper the following topics are dealt with: Principles of reactor core design and optimization, fuel management and safety concept for higher cycles and results of risk analyses (e.g. rod ejection, steam line break etc.) (RW)

Nuclear safety approach for PWRs design and operation

International Nuclear Information System (INIS)

Vignon, D.

1988-01-01

The implementation of France's major nuclear programme - 56 PWR units in service or under construction - has gone hand in hand with the development of an original philosophy in the field of nuclear safety. From an initial core of deterministic safety philosophy current in the seventies, which has been wholly retained and in some instances refined, a range of additions has been made to include consideration of a number of additional situations based on a probabilistic approach. This has resulted in a better coherence for safety and a mitigation of the severe accident probability. Furthermore, the establishment of emergency plans has enabled the Safety Authorities and the operator to adopt a coherent and logical approach to severe accidents with the aim of achieving greater defence in depth, this has resulted in the provision of certain additional measures designed to further reduce the consequences of severe accidents. This paper describes the culmination of this work, as exemplified in the new 1 400MWe - N4 advanced plant series currently under construction, of which the essential elements are also incorporated into all previous units, thereby giving them an equivalent level of safety. This now constitutes the French safety policy with respect to PWR nuclear units

The Safety Culture Enactment Questionnaire (SCEQ): Theoretical model and empirical validation.

Science.gov (United States)

de Castro, Borja López; Gracia, Francisco J; Tomás, Inés; Peiró, José M

2017-06-01

This paper presents the Safety Culture Enactment Questionnaire (SCEQ), designed to assess the degree to which safety is an enacted value in the day-to-day running of nuclear power plants (NPPs). The SCEQ is based on a theoretical safety culture model that is manifested in three fundamental components of the functioning and operation of any organization: strategic decisions, human resources practices, and daily activities and behaviors. The extent to which the importance of safety is enacted in each of these three components provides information about the pervasiveness of the safety culture in the NPP. To validate the SCEQ and the model on which it is based, two separate studies were carried out with data collection in 2008 and 2014, respectively. In Study 1, the SCEQ was administered to the employees of two Spanish NPPs (N=533) belonging to the same company. Participants in Study 2 included 598 employees from the same NPPs, who completed the SCEQ and other questionnaires measuring different safety outcomes (safety climate, safety satisfaction, job satisfaction and risky behaviors). Study 1 comprised item formulation and examination of the factorial structure and reliability of the SCEQ. Study 2 tested internal consistency and provided evidence of factorial validity, validity based on relationships with other variables, and discriminant validity between the SCEQ and safety climate. Exploratory Factor Analysis (EFA) carried out in Study 1 revealed a three-factor solution corresponding to the three components of the theoretical model. Reliability analyses showed strong internal consistency for the three scales of the SCEQ, and each of the 21 items on the questionnaire contributed to the homogeneity of its theoretically developed scale. Confirmatory Factor Analysis (CFA) carried out in Study 2 supported the internal structure of the SCEQ; internal consistency of the scales was also supported. Furthermore, the three scales of the SCEQ showed the expected correlation

Guidance for implementing an environmental, safety, and health-assurance program. Volume 15. A model plan for line organization environmental, safety, and health-assurance programs

Energy Technology Data Exchange (ETDEWEB)

Ellingson, A.C.; Trauth, C.A. Jr.

1982-01-01

This is 1 of 15 documents designed to illustrate how an Environmental, Safety and Health (ES and H) Assurance Program may be implemented. The generic definition of ES and H Assurance Programs is given in a companion document entitled An Environmental, Safety and Health Assurance Program Standard. This particular document presents a model operational-level ES and H Assurance Program that may be used as a guide by an operational-level organization in developing its own plan. The model presented here reflects the guidance given in the total series of 15 documents.

Transformational leadership and employee safety performance: a within-person, between-jobs design.

Science.gov (United States)

Inness, Michelle; Turner, Nick; Barling, Julian; Stride, Chris B

2010-07-01

We investigated the extent to which the safety performance (i.e., self-reported safety compliance and safety participation) of employees with 2 jobs was predicted by their respective supervisors' transformational leadership behaviors. We compared 2 within-person models: a context-specific model (i.e., transformational leadership experienced by employees in 1 context related to those same employees' safety performance only in that context) and a context-spillover model (i.e., transformational leadership experienced by employees in 1 context related to those same employees' safety performance in the same and other contexts). Our sample comprised 159 "moonlighters" (73 men, 86 women): employees who simultaneously hold 2 different jobs, each with a different supervisor, providing within-person data on the influence of different supervisors on employee safety performance across 2 job contexts. Having controlled for individual differences (negative affectivity and conscientiousness) and work characteristics (e.g., hours worked and length of relationship with supervisor), the context-specific model provided the best fit to the data among alternative nested models. Implications for the role of transformational leadership in promoting workplace safety are discussed.

Knowledge-Based Energy Damage Model for Evaluating Industrialised Building Systems (IBS Occupational Health and Safety (OHS Risk

Directory of Open Access Journals (Sweden)

Abas Nor Haslinda

2016-01-01

Full Text Available Malaysia’s construction industry has been long considered hazardous, owing to its poor health and safety record. It is proposed that one of the ways to improve safety and health in the construction industry is through the implementation of ‘off-site’ systems, commonly termed ‘industrialised building systems (IBS’ in Malaysia. This is deemed safer based on the risk concept of reduced exposure, brought about by the reduction in onsite workers; however, no method yet exists for determining the relative safety of various construction methods, including IBS. This study presents a comparative evaluation of the occupational health and safety (OHS risk presented by different construction approaches, namely IBS and traditional methods. The evaluation involved developing a model based on the concept of ‘argumentation theory’, which helps construction designers integrate the management of OHS risk into the design process. In addition, an ‘energy damage model’ was used as an underpinning framework. Development of the model was achieved through three phases, namely Phase I – knowledge acquisitaion, Phase II – argument trees mapping, and Phase III – validation of the model. The research revealed that different approaches/methods of construction projects carried a different level of energy damage, depending on how the activities were carried out. A study of the way in which the risks change from one construction process to another shows that there is a difference in the profile of OHS risk between IBS construction and traditional methods.Therefore, whether the option is an IBS or traditional approach, the fundamental idea of the model is to motivate construction designers or decision-makers to address safety in the design process and encourage them to examine carefully the probable OHS risk variables surrounding an action, thus preventing accidents in construction.

The design study of the JT-60SU device. No.8. Nuclear shielding and safety design

Energy Technology Data Exchange (ETDEWEB)

Miya, Naoyuki; Kikuchi, Mitsuru; Ushigusa, Kenkichi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment] [and others

1998-03-01

Results of nuclear shielding design study and safety analysis for the steady-state tokamak device JT-60SU are described. D-T operation (option) for two years is adopted in addition to ten years operation using deuterium. Design work has been done in accordance with general laws for radioisotopes handling in Japan as a guideline of safety evaluation, which is applied to the operation of present JT-60U device. Optimization of the shielding design for the device structure including vacuum vessel has been presented to meet with allowable limits of biological shielding determined in advance. It is shown that JT-60SU can be operated safely in the present JT-60 experimental building. It is planed to use 100g/year of tritium in D-T operation phase. A concept of multiple -barrier system is applied to the facility design to prevent propagation of tritium, in which the torus hall and the tritium removal room provide the tertiary confinement. From the design of atmosphere detritiation system for accidental tritium release, it is shown that tritium concentration level can be reduced to the allowable level after two weeks with reasonable compact size components. Safety assessment related to activation of coolant/air, and atmospheric tritium effluents are discussed. (author)

Development and Execution of the RUNSAFE Runway Safety Bayesian Belief Network Model

Science.gov (United States)

Green, Lawrence L.

2015-01-01

One focus area of the National Aeronautics and Space Administration (NASA) is to improve aviation safety. Runway safety is one such thrust of investigation and research. The two primary components of this runway safety research are in runway incursion (RI) and runway excursion (RE) events. These are adverse ground-based aviation incidents that endanger crew, passengers, aircraft and perhaps other nearby people or property. A runway incursion is the incorrect presence of an aircraft, vehicle or person on the protected area of a surface designated for the landing and take-off of aircraft; one class of RI events simultaneously involves two aircraft, such as one aircraft incorrectly landing on a runway while another aircraft is taking off from the same runway. A runway excursion is an incident involving only a single aircraft defined as a veer-off or overrun off the runway surface. Within the scope of this effort at NASA Langley Research Center (LaRC), generic RI, RE and combined (RI plus RE, or RUNSAFE) event models have each been developed and implemented as a Bayesian Belief Network (BBN). Descriptions of runway safety issues from the literature searches have been used to develop the BBN models. Numerous considerations surrounding the process of developing the event models have been documented in this report. The event models were then thoroughly reviewed by a Subject Matter Expert (SME) panel through multiple knowledge elicitation sessions. Numerous improvements to the model structure (definitions, node names, node states and the connecting link topology) were made by the SME panel. Sample executions of the final RUNSAFE model have been presented herein for baseline and worst-case scenarios. Finally, a parameter sensitivity analysis for a given scenario was performed to show the risk drivers. The NASA and LaRC research in runway safety event modeling through the use of BBN technology is important for several reasons. These include: 1) providing a means to clearly

Design and safety of the Sizewell pressurized water reactor

International Nuclear Information System (INIS)

Marshall, W.

1983-01-01

The Central Electricity Generating Board propose to build a pressurized water reactor at Sizewell in Suffolk. The PWR Task Force was set up in June 1981 to provide a communications centre for developing firm design proposals for this reactor. These were to follow the Standardized Nuclear Unit Power Plant System designed by Bechtel for the Westinghouse nuclear steam supply system for reactors built in the United States. Changes were required to the design to accommodate, for example, the use of two turbine generators and to satisfy British safety requirements. Differences exist between the British and American licensing procedures. In the UK the statutory responsibility for the safety of a nuclear power station rests unambiguously with the Generating Boards. In the U.S.A. the Nuclear Regulatory Commission issues detailed written instructions, which must be followed precisely. Much of the debate on the safety of nuclear power focuses on the risks of big nuclear accidents. It is necessary to explain to the public what, in a balanced perspective, the risks of accidents actually are. The long-term consequences can be presented in terms of reduction in life expectancy, increased chance of cancer or the equivalent pattern of compulsory cigarette smoking. (author)

Model-based Development of Safety-critical Functions and ISO 26262 Work Products using modified EAST-ADL

Directory of Open Access Journals (Sweden)

Bülent Sari

2017-07-01

Full Text Available Safety is becoming more and more important with the ever increasing level of safety related E/E Systems built into the cars. Increasing functionality of vehicle systems through electrification of power train, in future even more by autonomous driving, leads to complexity in designing system, software and safety architecture. ISO 26262 aims to reduce the complexity and to approve the traceability of the different safety activities. This paper presents an approach about model-based development of system, software and safety architecture using Electronics Architecture and Software Technology – Architecture Description Language (EAST-ADL, being in line with the relevant standard ISO 26262. In particular, we briefly discuss how the main safety related activities, such as hazard analysis and risk assessment, developing functional and technical safety concepts and performing safety analysis can be performed model-based and how the activities can be related with system and software development. The state-of-art is also provided and compared with the proposed approach.

Safety sign designs for children by considering effect of the colors preferences: A case study

Science.gov (United States)

Iftadi, Irwan; Nugraha, Dian Cahya; Jauhari, Wakhid Ahmad

2018-02-01

Color has become a major consideration in ergonomics. Color conveys a message and it is an important element in safety signs. The importance of colors usage in safety sign designs makes the colors research into one of the things that must be done before designing them. So far, research in the related field only focused on the adult's perspective without involving children's perspective in designing the safety signs. This paper aims to find out how children's perception towards colors affects the safety sign designs. This study consist of eight sections which are literature study, direct observation, determining referents and other parameters, determining research respondents, making the booklet, assessing the colors preferences, determining the design's parameter value and creating the safety sign designs. Limitation of the research are the objects are the students with the age of 10 - 11 years old in Grade IV and then the research is conducted in the school day and hours that apply to the school. Chi square test and odds ratio are employed to assess the colors preferences. Twelve safety sign designs are proposed by considering the children's colors perception. The designs are grouped into three types of sign which are Mandatory Action Sign, Warning Sign and Prohibition Sign. Six colors are used to draw the safety signs i.e. red, orange, yellow, green, blue and black. On the basis of the study, it is concluded that the colors that often appears in safety signs is green with the percentage of 75% and that rarely appears is red with the percentage of 8.33%.

Plant designer's view of the operator's role in nuclear plant safety

International Nuclear Information System (INIS)

Corcoran, W.R.; Church, J.F.; Cross, M.T.; Porter, N.J.

1981-01-01

The nuclear plant operator's role supports the design assumptions and equipment with four functional tasks. He must set up th plant for predictable response to disturbances, operate the plant so as to minimize the likelihood and severity of event initiators, assist in accomplishing the safety functions, and feed back operating experiences to reinforce or redefine the safety analyses' assumptions. The latter role enhances the operator effectiveness in the former three roles. The Safety Level Concept offers a different perspective that enables the operator to view his roles in nuclear plant safety. This paper outlines the operator's role in nuclear safety and classifies his tasks using the Safety Level Concept

Safety assessment in plant layout design using indexing approach: implementing inherent safety perspective. Part 2-Domino Hazard Index and case study.

Science.gov (United States)

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-12-15

The design of layout plans requires adequate assessment tools for the quantification of safety performance. The general focus of the present work is to introduce an inherent safety perspective at different points of the layout design process. In particular, index approaches for safety assessment and decision-making in the early stages of layout design are developed and discussed in this two-part contribution. Part 1 (accompanying paper) of the current work presents an integrated index approach for safety assessment of early plant layout. In the present paper (Part 2), an index for evaluation of the hazard related to the potential of domino effects is developed. The index considers the actual consequences of possible escalation scenarios and scores or ranks the subsequent accident propagation potential. The effects of inherent and passive protection measures are also assessed. The result is a rapid quantification of domino hazard potential that can provide substantial support for choices in the early stages of layout design. Additionally, a case study concerning selection among various layout options is presented and analyzed. The case study demonstrates the use and applicability of the indices developed in both parts of the current work and highlights the value of introducing inherent safety features early in layout design.

Civilian use transport of radioactive substances on public road. Volume 1: Shipment accreditation and approval requests. Guide Nr 7, Revision 2 of 15 February 2016. Volume 2: safety file of package models, European guide 'Package Design Safety Report'. Civilian use transport of radioactive packages or substances on public road. Volume 3: Compliance of package models not subject to accreditation. Guide Nr 7, Revision 7 of the 2015/11/13

International Nuclear Information System (INIS)

2016-01-01

After having recalled the regulatory context and sanctions susceptible to be applied, the first volume presents the accreditation process for a package model: file content, tests programme, safety file, certification studies, documents to be produced, accreditation prorogation request, accreditation extension or package model modifications, instruction delays. Some peculiar cases are described. Models of accreditation certificate are provided, and obligations concerning packaging design, fabrication, use and maintenance are briefly discussed. The second volume is a European technical guide which is intended to assist in the preparation of the Package Design Safety Report (PDSR) to demonstrate compliance of a package design for the transport of radioactive material with the regulatory requirements. It covers package designs requiring competent authority approval, and also covers package designs not requiring competent authority approval. In its first two chapters, this document provides a generic structure and contents of a PDSR which applies to all package types. The contents are described in a comprehensive way to cover all important aspects. Some of these aspects may not be applicable to specific package type and details can be found in the annexes which provide further guidance for the scope of the contents of a PDSR, specifically for each package type. The third volume presents recommendations made by the ASN for all stakeholders to guarantee the compliance to regulation of package models which are 'not submitted to competent authority approval'. After an indication and a comment of the regulatory context, it presents requirements to be applied for the design of those package models, and then describes and comments the structure and content of a safety file for such package models (generalities, authorised contents, packaging description, safety demonstration, receipt, use and maintenance instruction, management system). The last part presents the

Protection against internal fires and explosions in the design of nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

Experience of the past two decades in the operation of nuclear power plants and modern analysis techniques confirm that fire may be a real threat to nuclear safety and should receive adequate attention from the beginning of the design process throughout the life of the plant. Within the framework of the NUSS programme, a Safety Guide on fire protection had therefore been developed to enlarge on the general requirements given in the Code. Since its first publication in 1979, there has been considerable development in protection technology and analysis methods and after the Chernobyl accident it was decided to revise the existing Guide. This Safety Guide supplements the requirements established in Safety of Nuclear Power Plants: Design. It supersedes Safety Series No. 50-SG-D2 (Rev. 1), Fire Protection in Nuclear Power Plants: A Safety Guide, issued in 1992.The present Safety Guide is intended to advise designers, safety assessors and regulators on the concept of fire protection in the design of nuclear power plants and on recommended ways of implementing the concept in some detail in practice

The design features and safety concepts of the nuclear heating reactor developed in China

International Nuclear Information System (INIS)

Zheng Wenxiang; Wang Dazhong

1995-01-01

Based on the specific conditions of the nuclear heat applications and the development objectives of the advanced reactors, the nuclear heating reactor (NHR) exploited in China has adhered to the new safety concepts and been designed with a number of advanced features, including the integrated arrangement, full power natural circulation capacity, self-pressurized performance, dynamically-hydraulic control rod drive and passive safety systems, so that higher standard of safety as well as simplification in the plant systems and improvement in economic viability has been achieved. This paper describes the special consideration in the design as well as the main design features and safety concepts of the NHR. Some experimental and analytical results are also presented to demonstrate the NHR safety features

Hualong One's nuclear reactor core design and relative safety issues research

Energy Technology Data Exchange (ETDEWEB)

Yu, H., E-mail: yuhong_xing@126.com [Nuclear Power Inst. of China, Design and Research Sub-Inst., Chengdu, Sichuan (China)

2015-07-01

'Full text:' Hualong One, a third generation 1000MWe-class pressurized water reactor, is developed by China National Nuclear Cooperation (CNNC), based on the self-reliant technologies and experiences from China 40 years designing, construction, operation and maintenance of NPPs. In China, it has been approved to construct at Fuqing 5&6 and Fangchenggang 3&4. The Hualong One adopts advanced design features to dramatically enhance plant safety, economic efficiency and convenience of operation and maintenance. It consists of three loops with nominal thermal power output 3060 MWt and a 60-year design life. Its reactor core has 177 fuel assemblies, 18 month refueling interval (after initial cycle), and more than 15% thermal margin. It adopts low leakage loading pattern which can achieve better economy of the neutron, higher reactivity and lower radiation damage of pressure vessel. For the safety design, incorporating the feedback of Fukushima accident, the Hualong One has a combination of active and passive safety systems, a single station layout, double containment structure, and comprehensive implementation of defence-in-depth design principles. The new design features has been successfully evaluated to ensure that they enhance the performance and safety of Hualong One. Several experimental activates have been conducted, such as cavity injection and cooling system testing, passive containment heat removal system testing, and passive residual heat removal system of secondary side testing. The future improvements of Hualong reactor will focus on better economic core design and more reliable safety system. (author)