Review of design criteria and safety analysis of safety class electric building for fuel test loop

Energy Technology Data Exchange (ETDEWEB)

Kim, J. Y.

1998-02-01

Steady state fuel test loop will be equipped in HANARO to obtain the development and betterment of advanced fuel and materials through the irradiation tests. HANARO fuel test loop was designed for CANDU and PWR fuel testing. Safety related system of Fuel Test Loop such as emergency cooling water system, component cooling water system, safety ventilation system, high energy line break mitigation system and remote control room was required 1E class electric supply to meet the safety operation in accordance with related code. Therefore, FTL electric building was designed to construction and install the related equipment based on seismic category I. The objective of this study is to review the design criteria and analysis the safety function of safety class electric building for fuel test loop, and this results will become guidance for the irradiation testing in future. (author). 10 refs., 6 tabs., 30 figs.

Definition and means of maintaining the criticality detectors and alarms portion of the PFP safety envelope

Energy Technology Data Exchange (ETDEWEB)

White, W.F.

1997-05-13

The purpose of this document is to provide the definition and means of maintaining the Safety Envelope (SE) related to the Criticality Alarm System (CAS). This document provides amplification of the Limiting Condition for Operation (LCO) described in the Plutonium Finishing Plant (PFP) Operational Safety Requirements (OSR), WHC-SD-CP-OSR-010, Rev. 0, 1994, Section 3.1.2, Criticality Detectors and Alarms. This document, with its appendices, provides the following: (1) System functional requirements for determining system operability (Section 3); (2) A list of annotated system block diagrams which indicate the safety envelope boundaries (Appendix C); (3) A list of the Safety Class 1 and 2 Safety Envelope (SC-1/2 SE) equipment for input into the Master Component Index (Appendix B); (4) Functional requirements for individual SC-1/2 SE components, including appropriate setpoints and process parameters (Section 6 and Appendix A); (5) A list of the operational, maintenance and surveillance procedures necessary to operate and maintain the SC-1/2 SE components as required by the LCO (Section 6 and Appendix A).

Definition and means of maintaining the criticality detectors and alarms portion of the PFP safety envelope

International Nuclear Information System (INIS)

White, W.F.

1997-01-01

The purpose of this document is to provide the definition and means of maintaining the Safety Envelope (SE) related to the Criticality Alarm System (CAS). This document provides amplification of the Limiting Condition for Operation (LCO) described in the Plutonium Finishing Plant (PFP) Operational Safety Requirements (OSR), WHC-SD-CP-OSR-010, Rev. 0, 1994, Section 3.1.2, Criticality Detectors and Alarms. This document, with its appendices, provides the following: (1) System functional requirements for determining system operability (Section 3); (2) A list of annotated system block diagrams which indicate the safety envelope boundaries (Appendix C); (3) A list of the Safety Class 1 and 2 Safety Envelope (SC-1/2 SE) equipment for input into the Master Component Index (Appendix B); (4) Functional requirements for individual SC-1/2 SE components, including appropriate setpoints and process parameters (Section 6 and Appendix A); (5) A list of the operational, maintenance and surveillance procedures necessary to operate and maintain the SC-1/2 SE components as required by the LCO (Section 6 and Appendix A)

Discussion map and cooking classes: testing the effectiveness of teaching food safety to immigrants and refugees.

Science.gov (United States)

Gold, Abby; Yu, Nan; Buro, Brandy; Garden-Robinson, Julie

2014-01-01

To evaluate the effectiveness of a food safety map as an educational method with English language learners. English language learner community members (n = 73) were assigned randomly to participate in 1 of 3 experimental conditions: food safety map, cooking class, and control. Participants in the food safety map and cooking class conditions completed a pre-education demographic and cooking history questionnaire, a post-education knowledge and intention questionnaire, and a 2-week post-cooking and food safety habits assessment. Participants in the control group received no educational training but completed the pre- and 2-week post-education assessments. The cooking class and the map class were both effective in increasing food safety knowledge. Specifically, by comparing with the control group, they significantly increased participants' knowledge of safely cooking large meat (χ² [df = 2, n = 66] = 40.87; P effects on boosting food safety behavioral intention (measured right after the class). The data collected 2 weeks after the classes suggested that individuals who took the classes followed the suggested food behaviors more closely than those in the control group (P < .01). The food safety map is simple to use and prepare, beneficial for oral and visual learners, and inexpensive. Compared with a food safety cooking class, the map produces similar learning and behavioral outcomes. Copyright © 2014 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

Effects of hydroxyurea treatment for patients with hemoglobin SC disease.

Science.gov (United States)

Luchtman-Jones, Lori; Pressel, Sara; Hilliard, Lee; Brown, R Clark; Smith, Mary G; Thompson, Alexis A; Lee, Margaret T; Rothman, Jennifer; Rogers, Zora R; Owen, William; Imran, Hamayun; Thornburg, Courtney; Kwiatkowski, Janet L; Aygun, Banu; Nelson, Stephen; Roberts, Carla; Gauger, Cynthia; Piccone, Connie; Kalfa, Theodosia; Alvarez, Ofelia; Hassell, Kathryn; Davis, Barry R; Ware, Russell E

2016-02-01

Although hemoglobin SC (HbSC) disease is usually considered less severe than sickle cell anemia (SCA), which includes HbSS and HbS/β(0) -thalassemia genotypes, many patients with HbSC experience severe disease complications, including vaso-occlusive pain, acute chest syndrome, avascular necrosis, retinopathy, and poor quality of life. Fully 20 years after the clinical and laboratory efficacy of hydroxyurea was proven in adult SCA patients, the safety and utility of hydroxyurea treatment for HbSC patients remain unclear. Recent NHLBI evidence-based guidelines highlight this as a critical knowledge gap, noting HbSC accounts for ∼30% of sickle cell patients within the United States. To date, only 5 publications have reported short-term, incomplete, or conflicting laboratory and clinical outcomes of hydroxyurea treatment in a total of 71 adults and children with HbSC. We now report on a cohort of 133 adult and pediatric HbSC patients who received hydroxyurea, typically for recurrent vaso-occlusive pain. Hydroxyurea treatment was associated with a stable hemoglobin concentration; increased fetal hemoglobin (HbF) and mean corpuscular volume (MCV); and reduced white blood cell count (WBC), absolute neutrophil count (ANC), and absolute reticulocyte count (ARC). Reversible cytopenias occurred in 22% of patients, primarily neutropenia and thrombocytopenia. Painful events were reduced with hydroxyurea, more in patients >15 years old. These multicenter data support the safety and potentially salutary effects of hydroxyurea treatment for HbSC disease; however, a multicenter, placebo-controlled, Phase 3 clinical trial is needed to determine if hydroxyurea therapy has efficacy for patients with HbSC disease. © 2015 Wiley Periodicals, Inc.

Research and design of hanger and support series of nuclear safety class process piping

International Nuclear Information System (INIS)

Mao Chengzhang; Shi Jiemin

1995-12-01

Hangers and supports of nuclear safety class piping are an important part of primary system piping in a nuclear power plant. They will directly affect the reliability of operation, the period at construction and the investment for a nuclear power plant. It is an absolutely necessary job for Pakistan Chashma Nuclear Power Plant Project to research and design a series of piping supports in accordance with ASME-III NF. It is also an important designing for developing nuclear power plant later in China. After working over two years, a series of piping supports of nuclear safety class which have 57 types and more than 2460 specifications have been designed. This series is perfect, and can satisfy the requirements of piping final designing for nuclear power plant. This series of hangers and supports is mainly used in the process piping of nuclear safety class 1,2,3. They can also be used in other piping of nuclear safety class and piping with aseismic requirement of non-nuclear safety class

Project W-030 safety class upgrade summary report

International Nuclear Information System (INIS)

Kriskovich, J.R.

1998-01-01

This document presents a summary of safety class criteria for the 241-AY/AZ Tank Farm primary ventilation system upgrade under Project W-030, and recommends acceptance of the system as constructed, based on a review of supporting documentation

Development of SC structure modularization in Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Mun, Taeyoup [Korea Hydro and Nuclear Power Co., Ltd., Seoul (Korea, Republic of)

2008-04-15

New Focus on NPP are Rising Concerns on Global Warming, Potential energy crisis (geo-political), Improved reliability and safety of nuclear power plant, Advent of Generation 3+ NPP technology and Economical Energy Resource. New NPPs are 6 units in Korea and 23 in Asia being built, 32 units being planned in China by 2020 (150 by 2050), 10 units being planned in US by 2020 and IAEA expects $200 billions on NPP construction next 25 years (up to 30% of total world energy). {open_square} SC(Steel Plate Concrete) structure {center_dot} Steel Plate is used as a Structural Element instead of Reinforcing Bars in RC {center_dot} SC structure consists of Steel Plate with Headed Studs. Connected by Tie-bars - The Primary Purpose of Tie-bars is to Stiffen and Hold Together the Plates during Construction Process - Headed Studs are Welded to the Inside of Steel Plate for composite action {open_square} Benefits of SC Structure {center_dot} Shorten Construction Duration for Re bar, Forming and Scaffolding Works {center_dot} Minimize Site Labors {center_dot} Improve the Construction Quality {center_dot} Enable Construction Sites to be kept Clean {open_square} SC Modularization {center_dot} Fit for Modular Construction for Structural Features {center_dot} Fit for Modular Construction for Structural Features {center_dot} Inattentively Effective for Integrated Modules {center_dot} Pre-fabrication, Pre-assembly and Modularization {open_square} Project Overview {center_dot} Project Name: Development of SC structure for Modularization in NPP {center_dot} Project Type: Electric Power Industry R and D (Ministry of Knowledge Economy) {center_dot} Duration: Sep. 2005 {approx} Aug. 2008 (36 Months) {center_dot} Research Team and Scopes - Project Management: Korea Hydro and Nuclear Power Company (KHNP) - Development of Code and Standards for SC Structure: Korea Society of Steel Construction (KSSC) Korea Electric Power Research Institute (KEPRI) - Development of SC Structural Analysis and Design

Bullying prevention in schools by targeting cognitions, emotions, and behavior: Evaluating the effectiveness of the REBE-ViSC program.

Science.gov (United States)

Trip, Simona; Bora, Carmen; Sipos-Gug, Sebastian; Tocai, Ioana; Gradinger, Petra; Yanagida, Takuya; Strohmeier, Dagmar

2015-10-01

The effectiveness of a class-based antibullying prevention program on cognitions, emotions, and behaviors was investigated. The program consists of a cognitive-behavioral (Rational Emotive Behavioral Education; REBE) and a behavioral (Viennese Social Competence; ViSC) component. The REBE program is based on rational emotive behavioral theory and contains 9 student lessons. The ViSC program is based on social learning theory and comprises 10 student lessons. The order of the programs was experimentally manipulated. The REBE-ViSC program was implemented in 5 schools (14 classes), the ViSC-REBE program was implemented in 3 schools (9 classes), and 3 schools (11 classes) served as an untreated control group. Data were collected during 1 school year at pretest, midpoint, and posttest. Emotions (overt and internalizing anger), cognitions (learning and entitlement), and behaviors (bullying perpetration and bullying victimization) were measured with self-assessments. To examine the effectiveness of the REBE-ViSC/ViSC-REBE program, multilevel growth models were applied (time points at Level 1, individuals at Level 2, and classes at Level 3). The analyses revealed that the program effects differed depending on the order of the programs. The REBE-ViSC condition was more effective in changing negative emotions than the ViSC-REBE condition; both experimental conditions were effective in reducing dysfunctional cognitions, whereas no behavioral change was found in the 2 experimental groups when compared with the control group. To improve program effectiveness regarding behavioral changes, a multilevel whole-school approach including a teacher component is recommended. (c) 2015 APA, all rights reserved).

Spinning cylinder experiments SC-I and SC-II: A review of results and analyses provided to the FALSIRE project

International Nuclear Information System (INIS)

Morland, E.; Sherry, A.H.

1993-01-01

A series of six large-scale experiments have been carried out at AEA Technology using the Spinning Cylinder test facility. Results from two of those experiments (SC-I and SC-II) have been provided to Project FALSIRE and are reviewed in this paper. The Spinning Cylinder tests were carried out using hollow cylinders of 1.4m outer diameter, 0.2m wall thickness and 1.3m length, containing full-length axial defects and fabricated from a modified A508 Class 3 steel. The first Spinning Cylinder test (SC-I) was an investigation of stable ductile growth induced via mechanical (primary) loading and under conditions of contained yielding. Mechanical loading was provided in the hoop direction by rotating the cylinder about its major axis within an enclosed oven. The second test (SC-II) investigated stable ductile growth under severe thermal shock (secondary) loading again under conditions of contained yielding. In this case thermal shock was produced by spraying cold water on the inside surface of the heated cylinder whilst it was rotating. For each experiment, results are presented in terms of a number of variables, eg. crack growth, temperature, stress, strain and applied K and J. In addition, an overview of the analyses of the FALSIRE Phase-1 report is also presented with respect to test SC-I and SC-II. 4 refs., 14 figs., 13 tabs

Audit Report The Procurement of Safety Class/Safety-Significant Items at the Savannah River Site

International Nuclear Information System (INIS)

2009-01-01

The Department of Energy operates several nuclear facilities at its Savannah River Site, and several additional facilities are under construction. This includes the National Nuclear Security Administration's Tritium Extraction Facility (TEF) which is designated to help maintain the reliability of the U.S. nuclear stockpile. The Mixed Oxide Fuel Fabrication Facility (MOX Facility) is being constructed to manufacture commercial nuclear reactor fuel assemblies from weapon-grade plutonium oxide and depleted uranium. The Interim Salt Processing (ISP) project, managed by the Office of Environmental Management, will treat radioactive waste. The Department has committed to procuring products and services for nuclear-related activities that meet or exceed recognized quality assurance standards. Such standards help to ensure the safety and performance of these facilities. To that end, it issued Departmental Order 414.1C, Quality Assurance (QA Order). The QA Order requires the application of Quality Assurance Requirements for Nuclear Facility Applications (NQA-1) for nuclear-related activities. The NQA-1 standard provides requirements and guidelines for the establishment and execution of quality assurance programs during the siting, design, construction, operation, and decommissioning of nuclear facilities. These requirements, promulgated by the American Society of Mechanical Engineers, must be applied to 'safety-class' and 'safety-significant' structures, systems and components (SSCs). Safety-class SSCs are defined as those necessary to prevent exposure off site and to protect the public. Safety-significant SSCs are those whose failure could irreversibly impact worker safety such as a fatality, serious injury, or significant radiological or chemical exposure. Due to the importance of protecting the public, workers, and environment, we initiated an audit to determine whether the Department of Energy procured safety-class and safety-significant SSCs that met NQA-1 standards at

Product Engineering Class in the Software Safety Risk Taxonomy for Building Safety-Critical Systems

Science.gov (United States)

Hill, Janice; Victor, Daniel

2008-01-01

When software safety requirements are imposed on legacy safety-critical systems, retrospective safety cases need to be formulated as part of recertifying the systems for further use and risks must be documented and managed to give confidence for reusing the systems. The SEJ Software Development Risk Taxonomy [4] focuses on general software development issues. It does not, however, cover all the safety risks. The Software Safety Risk Taxonomy [8] was developed which provides a construct for eliciting and categorizing software safety risks in a straightforward manner. In this paper, we present extended work on the taxonomy for safety that incorporates the additional issues inherent in the development and maintenance of safety-critical systems with software. An instrument called a Software Safety Risk Taxonomy Based Questionnaire (TBQ) is generated containing questions addressing each safety attribute in the Software Safety Risk Taxonomy. Software safety risks are surfaced using the new TBQ and then analyzed. In this paper we give the definitions for the specialized Product Engineering Class within the Software Safety Risk Taxonomy. At the end of the paper, we present the tool known as the 'Legacy Systems Risk Database Tool' that is used to collect and analyze the data required to show traceability to a particular safety standard

Creation and Support of the State of Psychological Safety of Pupils of Cadet Classes

Directory of Open Access Journals (Sweden)

Baeva I.A.,

2017-01-01

Full Text Available The author's approach to the support of psychological safety in the educational process. As cadet classes make high demands to the capabilities and resources of the child, the task of tracking these educational programs in terms of psychological safety of children is particularly relevant. The study tested the assumption that the program support the state of psychological safety, implementing a risk-resource approach and aimed at updating / generation components of psychological safety (satisfaction, protection, reference, subjective well-being of the child in the Cadet educational environment, activity, will be effective when accompanied by cadet training programs. Testing of the developed program was carried out with students of third cadet classes (53 people in the experimental group and 26 in the control group. components and criteria of psychological safety of the younger schoolboy were determined on the basis of theoretical analysis. The methods of interrogation (questioning, testing, projective method examined the children, parents and teachers in the cadet classes to identify the initial and final levels of psychological safety of younger students. Statistical analysis were used cluster and discriminant analysis, chi-square test for contingency tables, sign test G. The article describes the features of the program, aimed at the formation and maintenance of psychological safety of younger pupils, pupils of cadet classes. The efficiency of it on all the selected criteria with a level of significance of not more than p <0,005. Ideas forming program can be used in the practice of psychological work in schools, as well as for further research of psychological safety of children in the educational environment of schools of different types and species.

Cold Vacuum Drying Safety Class Instrumentation and Control System Design Description

International Nuclear Information System (INIS)

WHITEHURST, R.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) Safety Class Instrumentation and Control system (SCIC). The SCIC provides safety functions and features to protect the environment, off-site and on-site personnel and equipment. The function of the SCIC is to provide automatic trip features, valve interlocks, alarms, indication and control for the cold vacuum drying process

SC*994C>T causes the Sc(null) phenotype in Pacific Islanders and successful transfusion of Sc3+ blood to a patient with anti-Sc3.

Science.gov (United States)

Reid, Marion E; Hue-Roye, Kim; Velliquette, Randall W; Larimore, Kathleen; Moscarelli, Sue; Ohswaldt, Nicolas; Lomas-Francis, Christine

2013-01-01

Antigens in the SC blood group system are expressed by the human erythrocyte membrane-associated protein (ERMAP).Two molecular bases have been reported for the Sc,un phenotype:SC*307del2 and SC*994C>T. We report our investigation of the molecular background of five Sc,n1 individuals from the Pacific Islands and describe the successful transfusion of Sc3+ blood to a patient with anti-Sc3 in her plasma. SC (ERMAP) exons 2,3, and 12 and their flanking intronic regions were analyzed. TheSC*994C>T change introduces a restriction enzyme cleavage site for Tsp45I, and polymerase chain reaction (PCR) products from exon 12 were subjected to this PCR-restriction fragment length polymorphism (RFLP) assay. The five samples had the variant SC*994T/T. One sample, from a first cousin of one Marshallese proband, was heterozygous for SC*1514C/T (in the 3' untranslated region); the other four samples were SC*1514C/C(consensus sequence). Samples from white donors (n = 100) and African American donors (n = 99) were tested using the Tsp45IPCR-RFLP assay; all gave a banding pattern that was consistent with the SC*994C/C consensus sequence. In all five samples,our analyses showed homozygosity for the nonsense nucleotide change SC*994C>Tin an allele carrying the nucleotide associated with SLd. Further investigation determined that one of the probands reported previously with the SC*994C>T change was from the Marshall Islands (which form part of the Micronesian Pacific Islands) and the other was from an unspecified location within the large collection of Pacific Islands. Taken together, the five known probands with the SC*994C>T silencing nucleotide change were from the Pacific Islands.

Safety learning from drugs of the same class

DEFF Research Database (Denmark)

Stefansdottir, G; Knol, M J; Arnardottir, A H

2012-01-01

This study was aimed at assessing the extent of safety learning from data pertaining to other drugs of the same class. We studied drug classes for which the first and second drugs were centrally registered in the European Union from 1995 to 2008. We assessed whether adverse drug reactions (ADRs......) associated with one of the drugs also appeared in the Summary of Product Characteristics (SPC) of the other drug, either initially or during the postmarketing phase. We identified 977 ADRs from 19 drug pairs, of which 393 ADRs (40.2%) were listed in the SPCs of both drugs of a pair. Of these 393 that were...... present in both SPCs of a drug pair, 241 (61.3%) were present when the drug entered the market and 152 (30.7%) appeared in the postmarketing phase. The mention of ADRs in the SPCs of both same-class drugs in the postmarketing phase was associated with type A ADRs, marketing in the same regulator country...

Sc-W-Si and Sc-W-Ge ternary systems

International Nuclear Information System (INIS)

Kotur, B.Ya.; Voznyak, O.M.; Bodak, O.I.

1989-01-01

Phase equilibria in Sc-W-Si and Sc-W-Ge ternary systems are investigated at 1070 K. Sc 2+x W 3-x Si 4 ternary compound (0≤x≤1) is determined, its crystal structure (Ce 2 Sc 3 Si 4 structural type), as well as, change of elementary cell parameters and microhardness within homogeneity range are determined. Regularities of component interaction within Sc-M-Si(Ge) (M-Cr, Mo, W) ternary system are determined. Ternary systems with Mo and W are more closer to each other according to the phase equilibria character, than to ternary systems with Cr

Analysis on typical illegal events for nuclear safety class 1 valve

International Nuclear Information System (INIS)

Tian Dongqing; Gao Runsheng; Jiao Dianhui; Yang Lili; Chen Peng

2014-01-01

Illegal welding events of nuclear safety class l valve forging occurred to the manufacturer, while the valve was returned to be repaired. Illegal nondestructive test event of nuclear safety class valve occurred also to the manufacturer in the manufacturing process. The two events have resulted in quality incipient fault for the installed valves and the valves in the manufacturing process. It was reflected that operation of the factory quality assurance system isn't activated, and nuclear power engineering and operating company have insufficient supervision. The event-related parties should strengthen quality management and process control, get rid of the quality incipient fault, and experience feedback should be done well to guarantee quality of equipment in nuclear power plant. (authors)

The Designing Bus for Nuclear Safety Class Controller

Energy Technology Data Exchange (ETDEWEB)

Lee, Dongil; Lee, Myeongkyun; Yun, Donghwa [PONUTech Co,. Ltd., Research Institute, Ulsan (Korea, Republic of); Ryoo, Kwangki [Hanbat National Univ., Daejeon (Korea, Republic of)

2013-10-15

EtherCAT (Ethernet for Control Automation Technology) is based on the IEEE 802.3 standard as one of the communication which is the I/O (Input/Output), sensors and communication function of PLC (Programmable Logic Controller) in industry and factory environment use is increasing. The Nuclear Safety Class Controller implemented by the EtherCAT applied bus can be shown the improving performance of data transmission in the controller.

The Designing Bus for Nuclear Safety Class Controller

International Nuclear Information System (INIS)

Lee, Dongil; Lee, Myeongkyun; Yun, Donghwa; Ryoo, Kwangki

2013-01-01

EtherCAT (Ethernet for Control Automation Technology) is based on the IEEE 802.3 standard as one of the communication which is the I/O (Input/Output), sensors and communication function of PLC (Programmable Logic Controller) in industry and factory environment use is increasing. The Nuclear Safety Class Controller implemented by the EtherCAT applied bus can be shown the improving performance of data transmission in the controller

A decomposition of the class of semiconvex games

NARCIS (Netherlands)

Driessen, Theo; Derks, J.J.M.

1993-01-01

The paper studies the classSC N of cooperative games with player setN which have the semiconvexity property.SC N is decomposed into an algebraic sum of convex cones of games for which generating sets are available. The union of these sets thus forms a generating set forSC N . Special attention is

Fatigue check of nuclear safety class 1 reactor coolant pipe

International Nuclear Information System (INIS)

Wang Qing; Fang Yonggang; Chu Qibao; Xu Yu; Li Hailong

2015-01-01

Fatigue and thermal ratcheting analyses of nuclear safety Class 1 reactor coolant pipe in a nuclear power plant were independently carried out in this paper. The software used for calculation is ROCOCO, which is based on RCC-M code. The difference of nuclear safety Class 1 pipe fatigue evaluation between RCC-M code and ASME code was compared. The main aspects of comparison include the calculation scoping of fatigue design, the calculation method of primary plus secondary stress intensity, the elastic-plastic correction coefficient calculation, and the dynamic load combination method etc. By correcting inconsistent algorithm of ASME code within ROCOCO, the fatigue usage factor and thermal ratcheting design margin of 65 mm and 55 mm wall thickness of the pipe were obtained. The results show that the minimum wall thickness of the pipe must exceed 55 mm and the design value of the thermal ratcheting of 55 mm wall thickness reaches 95% of the allowable value. (authors)

Dedication for Safety-Related Fuses used in Class-1E Power System

International Nuclear Information System (INIS)

Hong, Younghee

2014-01-01

The safety-related fuses used in class-1E power system provide overcurrent protection for electrical system and isolate the class 1E circuit from a fault or overload condition. These days, the number of nuclear grade suppliers has been reduced. Accordingly, commercial grade, instead of safety-related, fuses are procured and used in the utilities through the dedication process. Therefore, this paper introduces the commercial grade fuse dedication process/engineering and how to assure the quality requirements with this process and engineering. The fuses used in class-1E power system are to protect overcurrent and to isolate fault. Therefore the fuse for acceptance in order to improve the quality and reliability for commercial grade fuses shall be dedicated. The fuse resistance value may be useful as an indicator of acceptance. The current carrying capacity test can change the fuse performance properties. Therefore these critical characteristics are needed for additional review and analysis with fuse manufactures

Original Research: Use of hydroxyurea and phlebotomy in pediatric patients with hemoglobin SC disease.

Science.gov (United States)

Summarell, Carly C Ginter; Sheehan, Vivien A

2016-04-01

Hydroxyurea is an excellent therapeutic agent for the pharmacological induction of HbF in patients with sickle cell disease (SCD). However, all completed clinical trials of hydroxyurea have excluded patients with hemoglobin SC (HbSC) disease. HbSC differs significantly in pathophysiology from HbSS, as HbC does not sickle, but instead causes cellular dehydration which potentiates sickling of HbS. Many severely affected HbSC patients have been placed on hydroxyurea on a case by case basis, but there are no large scale prospective data on safety or efficacy of hydroxyurea in this subset of patients with SCD. Here, we report a case series of 14 pediatric patients with HbSC treated to maximum tolerated dose (MTD) with hydroxyurea. Those who failed to show clinical improvement after at least six months at MTD were offered phlebotomy in addition to hydroxyurea. Five out of 11 patients with HbSC who achieved MTD failed to demonstrate clinical improvement on hydroxyurea. Of the four placed on dual hydroxyurea and phlebotomy therapy, all showed at least partial clinical improvement. Percent dense red blood cells (%DRBC) were measured via an ADVIA hematology analyzer. A marked rise in percent dense cells preceded clinical complications in three patients. Dual therapy with hydroxyurea and phlebotomy may be an effective approach to patients with HbSC that do not experience improvement with hydroxyurea alone. Monitoring of %DRBC may predict adverse events and aid in assessing hydroxyurea compliance. Large scale clinical trials are needed to evaluate the safety and efficacy of hydroxyurea and hydroxyurea with phlebotomy in patients with HbSC disease. © 2016 by the Society for Experimental Biology and Medicine.

Safety and adverse events of neoadjuvant short-course hyperfractionated accelerated radiotherapy (SC-HART) for rectal cancer

International Nuclear Information System (INIS)

Doi, Hiroshi; Kamikonya, Norihiko; Hirota, Shozo; Beppu, Naohito; Yanagi, Hidenori

2014-01-01

We presented good tolerability and short-term outcomes of neoadjuvant short-course hyperfractionated accelerated radiotherapy (SC-HART; 25 Gy in 10 fractions for 5 days) combined with chemotherapy in a total of 73 patients with lower rectal cancer. Age, gender, tumor differentiation, and the type of surgery seemed to have no apparent effects on toxicity of SC-HART. SC-HART appeared to have a good feasibility for use in further clinical trials. (author)

Revised Safety Instruction 41 (IS41 REV.)

CERN Multimedia

SC Secretariat

2005-01-01

Please note that the Revised Safety Instruction No. 41 (IS41 REV.), entitled 'The use of plastic and other non-metallic materials at CERN with respect to fire safety and radiation resistance' is available on the web at the following url: https://edms.cern.ch/document/335806/LAST_RELEASED Paper copies can also be obtained from the SC Unit Secretariat, e-mail: sc.secretariat@cern.ch SC Secretariat

Investigating ethnic minorities' perceptions of safety climate in the construction industry.

Science.gov (United States)

Chan, Albert P C; Wong, Francis K W; Hon, Carol K H; Lyu, Sainan; Javed, Arshad Ali

2017-12-01

An increasing number of ethnic minorities (EMs) have been employed in the construction industry to alleviate severe labor shortages in many countries. Unfortunately, statistics show that EMs have higher fatal and non-fatal occupational injury rates than their local counterparts. However, EMs are often underrepresented in safety climate (SC) research as they are difficult to reach and gauge their perception. A positive relationship has been widely found between SC and safety performance. Understanding the safety perceptions of EMs helps to reduce injuries and improve their safety performance. Based on a sample of 320 EMs from 20 companies in the construction industry, exploratory factor analysis (EFA) and confirmatory factor analysis (CFA) were used to identify the SC factors of EMs, and validate the extracted factors, respectively. Multivariate analysis of variance was undertaken to examine mean differences in perceptions of SC by personal characteristics. Three SC factors for EMs encapsulating 16 variables were identified through EFA. The hypothesized CFA model for a three-factor structure derived from EFA showed a satisfactory goodness-of-fit, composite reliability, and construct validity. Three SC factors were identified, namely: (a) safety management commitment, safety resources, and safety communication; (b) employee's involvement and workmate's influence; and (c) perception of safety rules, procedures and risks. The perceptions of SC differed significantly by nationality, marital status, the number of family members supported, and drinking habit. This study reveals the perception of EMs toward SC. The findings highlight the areas for safety improvement and provide leading indicators for safety performance of EMs. The findings are also enlightening for countries with a number of EMs, such as the United Sates, the United Kingdom, Australia, Singapore, and the Middle East. Copyright © 2017. Published by Elsevier Ltd.

Structure and bonding of ScCN and ScNC: Ground and low-lying states

International Nuclear Information System (INIS)

Kalemos, Apostolos; Metropoulos, Aristophanes; Mavridis, Aristides

2012-01-01

Graphical abstract: The experimentally unknown systems ScCN and ScNC have been studied through single reference CISD and CCSD(T) methods. A total of 20 = 10 (ScCN) + 10 (ScNC) states were examined. All states are quite ionic whereas ScNC(X ∼3 Δ) is stabler than ScCN(X ∼3 Δ) by ∼5 kcal/mol. Display Omitted Highlights: ► We have studied through ab initio methods the polytopic system Sc[CN]. ► A series of low lying states for both isomeric forms have been examined. ► Around equilibrium the system displays a pronounced Sc + [CN] − ionic character. - Abstract: We have studied the experimentally unknown Sc[CN] molecular system in both its isomeric forms, scandium cyanide (ScCN) and isocyanide (ScNC), through ab initio computations. We report energetics, geometries, harmonic frequencies, and dipole moments for the first 20 Sc[CN] states correlating diabatically to Sc + ( 3 D, 1 D, 3 F) + CN − (X 1 Σ + ). Both isomers have a pronounced ionic character around equilibrium due to the high electron affinity of the CN group and the low ionization energy of the Sc atom. According to our calculations the ScNC isomer (X ∼3 Δ) is stabler than the ScCN(X ∼3 Δ) by ∼5 kcal/mol.

Safety Commission databases support

CERN Document Server

Petit, S; CERN. Geneva. TS Department

2005-01-01

A collaboration project between the Safety Commission (SC) and the Controls, Safety and Engineering databases group (TS/CSE) started last year. The aim of this collaboration is to transfer several SC applications from their local environments onto the D7i-MTF EDMS framework, for which the TS/CSE group is responsible. Different domains of activity and projects have been defined in the areas of equipment management, safety inspections, accidents and risks management. Priorities have been established in collaboration with SC. This paper presents the new Safety Inspections Management system (SIM) which will be put in production before the summer 2005 and reviews the constraints of both the users and the development and operational framework that needed to be taken into account. The technical solutions adopted to assure a successful production start-up and operation of the SIM system are described. Progress on other on-going projects and plans for the next year are also reported.

QUALITY MANAGEMENT OF BAKERY PRODUCTS: A CASE STUDY IN SC

Directory of Open Access Journals (Sweden)

Nicoleta- Luminiţa STRÂMBEANU RISTEA

2013-01-01

Full Text Available The paper aimed to present the benefits of implementing HACCP (Hazard Analysis and Critical Control Points to company S.C. "DOBRE AND SONS" S.R.L. Constanta, Romania. The data have been provided by the above mentioned manufacturer. The objectives of S.C. "DOBRE AND SONS" S.R.L. are protecting the health of the consumers of the products and their satisfaction regarding the consumption of products that are nutritional, tasty, fresh, free from microbiological, chemical and physical hazard, as well as possessing stable properties during the validity for consumption. In this respect, there has been implemented and maintained an integrated management system of food quality and safety according to SR EN ISO 9001:2008, SR EN ISO 22000:2005 and according to IFS standard, version 5/2007, which consists of determining the potential biological, chemical and physical hazards that might affect the safety of bread and bakery products, or the health of the consumer. HACCP team is analyzing hazard using one of the recommended techniques: brainstorming or the cause - effect diagram. In conclusion, the company S.C. "DOBRE AND SONS" S.R.L. Constanta, Romania provides awareness and employee involvement at all levels in achieving the appointed objectives.

Assessment of safety culture in the Iranian nuclear installations

International Nuclear Information System (INIS)

Farahani, H.F.; Davilu, H.; Sepanloo, K.

2005-01-01

The deficient safety culture (S.C) is the center of safety issues of nuclear industry. To benefit from the advantages of nuclear technology and considering the fact of potential hazards of accidents in nuclear installations it is essential to view safety as the highest priority. S.C is an amalgamation of values, standards, morals and norms of acceptable behavior. Organizations having effective S.C show constant commitment to safety as a top level priority. Furthermore, the personnel of a nuclear facility shall recognize the safety significance of their tasks. Many people even those who work in the field of safety do not have a correct understanding of what S.C looks like in practical sense. In this study, by conducting a survey according to IAEA-TECDOC-1329 in some nuclear facilities, the S.C within the Iranian nuclear facilities is assessed. The human and organizational factors in Tehran Research Reactor are evaluated using a questionnaire method with active participation of the reactor operators. The results sho w that the operators are pretty aware of the subject. Also it has been identified some areas of improvement. (authors)

Sc-45 nuclear magnetic resonance analysis of precipitation in dilute Al-Sc alloys

NARCIS (Netherlands)

Celotto, S; Bastow, TJ

Nuclear magnetic resonance (NMR) with Sc-45 is used to determine the solid solubility of scandium in aluminium and to follow the precipitation of Al3Sc during the ageing of an Al-0.06 at.% Sc alloy via the two fully resolved peaks, corresponding to Sc in the solid solution Al matrix and to Sc in the

Crystal structure and phase stability of AlSc in the near-equiatomic Al–Sc alloy

Energy Technology Data Exchange (ETDEWEB)

Li, Juan; Huang, Li; Liang, Yongfeng [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, 30 Xueyuan Road, Beijing 100083 (China); Ye, Feng, E-mail: yefeng@skl.ustb.edu.cn [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, 30 Xueyuan Road, Beijing 100083 (China); Lin, Junpin [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, 30 Xueyuan Road, Beijing 100083 (China); Shang, Shunli; Liu, Zikui [Department of Materials Science and Engineering, The Pennsylvania State University, University Park, PA 16802 (United States)

2015-01-05

Highlights: • Two lattice structures of equiatomic Al–Sc compounds are confirmed. • Al–Sc phase at Sc 50 at.% has a space group of Pbam. • Al–Sc phase at Sc 55 at.% has a space group of B2. • B2 AlSc is a metastable phase with Sc 50 at.%. • Lattice transition between two compounds is proposed under local thermal stress. - Abstract: Intermetallic compound AlSc is found in the equiatomic Al–Sc binary alloy. The present work indicates that the orthorhombic AlSc with the Au{sub 2}CuZn-type structure can be formed at 50 at.% Sc, while the CsCl-type (B2) AlSc will be formed at 55 at.% Sc. After annealing at 1100 °C, some orthorhombic AlSc grains transit to the B2 structure, and the annealing at lower temperatures leads to the disappearance of B2 phase, indicating that the B2 AlSc is also a metastable phase in the alloy at lower Sc content (<50 at.%). First-principle calculations at 0 K reveal that the orthorhombic AlSc is more stable than the B2 AlSc with the energy difference between them being 5.4 meV/atom. The fast transition between these two phases, which cannot be interpreted by the mechanism of atomic diffusion, was tentatively analyzed by the volume change based on the calculated atomic positions of these two phases.

46 CFR 7.70 - Folly Island, SC to Hilton Head Island, SC.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Folly Island, SC to Hilton Head Island, SC. 7.70 Section... BOUNDARY LINES Atlantic Coast § 7.70 Folly Island, SC to Hilton Head Island, SC. (a) A line drawn from the...′ W. (Port Royal Sound Lighted Whistle Buoy “2PR”); thence to the easternmost extremity of Hilton Head...

Two sides of the safety coin?: How patient engagement and safety climate jointly affect error occurrence in hospital units.

Science.gov (United States)

Schiffinger, Michael; Latzke, Markus; Steyrer, Johannes

2016-01-01

Safety climate (SC) and more recently patient engagement (PE) have been identified as potential determinants of patient safety, but conceptual and empirical studies combining both are lacking. On the basis of extant theories and concepts in safety research, this study investigates the effect of PE in conjunction with SC on perceived error occurrence (pEO) in hospitals, controlling for various staff-, patient-, and hospital-related variables as well as the amount of stress and (lack of) organizational support experienced by staff. Besides the main effects of PE and SC on error occurrence, their interaction is examined, too. In 66 hospital units, 4,345 patients assessed the degree of PE, and 811 staff assessed SC and pEO. PE was measured with a new instrument, capturing its core elements according to a recent literature review: Information Provision (both active and passive) and Activation and Collaboration. SC and pEO were measured with validated German-language questionnaires. Besides standard regression and correlational analyses, partial least squares analysis was employed to model the main and interaction effects of PE and SC on pEO, also controlling for stress and (lack of) support perceived by staff, various staff and patient attributes, and potential single-source bias. Both PE and SC are associated with lower pEO, to a similar extent. The joint effect of these predictors suggests a substitution rather than mutually reinforcing interaction. Accounting for control variables and/or potential single-source bias slightly attenuates some effects without altering the results. Ignoring PE potentially amounts to forgoing a potential source of additional safety. On the other hand, despite the abovementioned substitution effect and conjectures of SC being inert, PE should not be considered as a replacement for SC.

Safety culture relationships with hospital nursing sensitive metrics.

Science.gov (United States)

Brown, Diane Storer; Wolosin, Robert

2013-01-01

Public demand for safer care has catapulted the healthcare industry's efforts to understand relationships between patient safety and hospital performance. This study explored linkages between staff perceptions of safety culture (SC) and ongoing measures of hospital nursing unit-based structures, care processes, and adverse patient outcomes. Relationships between nursing-sensitive measures of hospital performance and SC were explored at the unit-level from 9 California hospitals and 37 nursing units. SC perceptions were measured 6 months prior to collection of nursing metrics and relationships between the two sets of data were explored using correlational and regression analyses. Significant relationships were found with reported falls and process measures for fall prevention. Multiple associations were identified with SC and the structure of care delivery: skill mix, staff turnover, and workload intensity demonstrated significant relationships with SC, explaining 22-45% of the variance. SC was an important factor to understand in the quest to advance safe patient care. These findings have affordability and care quality implications for hospital leadership. When senior leaders prioritized a safety culture, patient outcomes may have improved with less staff turnover and more productivity. A business case could be made for investing in patient safety systems to provide reliably safe care. © 2013 National Association for Healthcare Quality.

Modeling the Relationship between Safety Climate and Safety Performance in a Developing Construction Industry: A Cross-Cultural Validation Study.

Science.gov (United States)

Zahoor, Hafiz; Chan, Albert P C; Utama, Wahyudi P; Gao, Ran; Zafar, Irfan

2017-03-28

This study attempts to validate a safety performance (SP) measurement model in the cross-cultural setting of a developing country. In addition, it highlights the variations in investigating the relationship between safety climate (SC) factors and SP indicators. The data were collected from forty under-construction multi-storey building projects in Pakistan. Based on the results of exploratory factor analysis, a SP measurement model was hypothesized. It was tested and validated by conducting confirmatory factor analysis on calibration and validation sub-samples respectively. The study confirmed the significant positive impact of SC on safety compliance and safety participation , and negative impact on number of self-reported accidents/injuries . However, number of near-misses could not be retained in the final SP model because it attained a lower standardized path coefficient value. Moreover, instead of safety participation , safety compliance established a stronger impact on SP. The study uncovered safety enforcement and promotion as a novel SC factor, whereas safety rules and work practices was identified as the most neglected factor. The study contributed to the body of knowledge by unveiling the deviations in existing dimensions of SC and SP. The refined model is expected to concisely measure the SP in the Pakistani construction industry, however, caution must be exercised while generalizing the study results to other developing countries.

High-resolution clean-sc

NARCIS (Netherlands)

Sijtsma, P.; Snellen, M.

2016-01-01

In this paper a high-resolution extension of CLEAN-SC is proposed: HR-CLEAN-SC. Where CLEAN-SC uses peak sources in “dirty maps” to define so-called source components, HR-CLEAN-SC takes advantage of the fact that source components can likewise be derived from points at some distance from the peak,

Cold Vacuum Drying Safety Class Instrumentation and Control System Design Description SYS 93-2

International Nuclear Information System (INIS)

WHITEHURST, R.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) Safety Class Instrumentation and Control system (SCIC). The SCIC provides safety functions and features to protect the environment, off-site and on-site personnel and equipment. The function of the SCIC is to provide automatic trip features, valve interlocks, alarms, indication and control for the cold vacuum drying process

Mochovce NPP safety improvement and completion

International Nuclear Information System (INIS)

1997-01-01

6th Nuclear society information meeting dealt with the completion of the Mochovce NPP with regard to implementation of safety measures. It was aimed to next problems: I. 'Survey' presentation on the situation of the nuclear power industry in partner countries; II. Basic technical presentations; III. Presentations of operators of the other VVER 440/213 NPPs on their activities in the field of safety improvement in relation to IAEA recommendations; IV. Technical solutions of safety improvements ranked with IAEA degree 3 (Report SC 108 VVER); V: Technical solutions of selected Safety Measures ranked with IAEA degree 2 and 1 (Report SC 108 VVER)

Experimental and theoretical investigation of Cr_1-xSc_xN solid solutions for thermoelectrics

DEFF Research Database (Denmark)

Kerdsongpanya, Sit; Sun, Bo; Eriksson, Fredrik

2016-01-01

The ScN- and CrN-based transition-metal nitrides have recently emerged as a novel and unexpected class of materials for thermoelectrics. These materials constitute well-defined model systems for investigating mixing thermodynamics, phase stability, and band structure aiming for property tailoring......-factor improvement by Sc3d orbital delocalization on Cr3d electrons giving decreasing electrical resistivity, while localized Cr3d orbitals with a large DOS slope may yield an improved Seebeck coefficient. Sc-rich solid solutions show a large improvement in power factor compared to pure ScN, and all films have power...

Culture of safety. Indicators of culture of safety. Stage of culture of safety. Optimization of radiating protection. Principle of precaution. Principle ALARA. Procedure ALARA

International Nuclear Information System (INIS)

Mursa, E.

2006-01-01

Object of research: is the theory and practice of optimization of radiating protection according to recommendations of the international organizations, realization of principle ALARA and maintenance of culture of safety (SC) on the nuclear power plant. The purpose of work - to consider the general aspects of realization of principle ALARA, conceptual bases of culture of safety, as principle of management, and practice of their introduction on the nuclear power plant. The work has the experts' report character in which the following questions are presented: The recommendations materials of the IAEA and other international organizations have been assembled, systematized and analyzed. The definitions, characteristics and universal SC features, and also indicators as a problem of parameters and quantitative SC measurements are described in details advanced. The ALARA principles - principle of precaution; not acceptance of zero risk; choice of a principle ALARA; model of acceptable radiation risk are described. The methodology of an estimation of culture of safety level and practical realization of the ALARA principle in separate organization is shown on a practical example. The SC general estimation at a national level in Republic of Moldova have been done. Taking into consideration that now Safety Culture politics are introduced only in relation to APS, in this paper the attempt of application of Safety Culture methodology to Radiological Objects have been made (Oncological Institute of the Republic of Moldova and Special Objects No.5101 and 5102 for a long time Storage of the Radioactive Waste). (authors)

Journey Toward High Reliability: A Comprehensive Safety Program to Improve Quality of Care and Safety Culture in a Large, Multisite Radiation Oncology Department.

Science.gov (United States)

Woodhouse, Kristina Demas; Volz, Edna; Maity, Amit; Gabriel, Peter E; Solberg, Timothy D; Bergendahl, Howard W; Hahn, Stephen M

2016-05-01

High-reliability organizations (HROs) focus on continuous identification and improvement of safety issues. We sought to advance a large, multisite radiation oncology department toward high reliability through the implementation of a comprehensive safety culture (SC) program at the University of Pennsylvania Department of Radiation Oncology. In 2011, with guidance from safety literature and experts in HROs, we designed an SC framework to reduce radiation errors. All state-reported medical events (SRMEs) from 2009 to 2016 were retrospectively reviewed and plotted on a control chart. Changes in SC grade were assessed using the Agency for Healthcare Research and Quality Hospital Survey. Outcomes measured included the number of radiation treatment fractions and days between SRMEs, as well as SC grade. Multifaceted safety initiatives were implemented at our main academic center and across all network sites. Postintervention results demonstrate increased staff fundamental safety knowledge, enhanced peer review with an electronic system, and special cause variation of SRMEs on control chart analysis. From 2009 to 2016, the number of days and fractions between SRMEs significantly increased, from a mean of 174 to 541 days (P safety framework. Our multifaceted initiatives, focusing on culture and system changes, can be successfully implemented in a large academic radiation oncology department to yield measurable improvements in SC and outcomes. Copyright © 2016 by American Society of Clinical Oncology.

Static resistance function for steel-plate composite (SC) walls subject to impactive loading

International Nuclear Information System (INIS)

Bruhl, Jakob C.; Varma, Amit H.; Kim, Joo Min

2015-01-01

Highlights: • An idealized static resistance function for SC walls is proposed. • The influence of design parameters on static resistance is explained. • SDOF models can accurately estimate global response of SC walls to missile impact. - Abstract: Steel-plate composite (SC) walls consist of a plain concrete core reinforced with two steel faceplates on the surfaces. Modules (consisting of steel faceplates, shear connectors and tie-bars) can be shop-fabricated and shipped to the site for erection and concrete casting, which expedites construction schedule and thus economy. SC structures have recently been used in nuclear power plant designs and are being considered for the next generation of small modular reactors. Design for impactive and impulsive loading is an important consideration for SC walls in safety-related nuclear facilities. The authors have previously developed design methods to prevent local failure (perforation) of SC walls due to missile impact. This paper presents the development of static resistance functions for use in single-degree-of-freedom (SDOF) analyses to predict the maximum displacement response of SC walls subjected to missile impact and designed to resist local failure (perforation). The static resistance function for SC walls is developed using results of numerical analyses and parametric studies conducted using benchmarked 3D finite element (FE) models. The influence of various design parameters are discussed and used to develop idealized bilinear resistance functions for SC walls with fixed edges and simply supported edges. Results from dynamic non-linear FE analysis of SC panels subjected to rigid missile impact are compared with the maximum displacements predicted by SDOF analyses using the bilinear resistance function.

Static resistance function for steel-plate composite (SC) walls subject to impactive loading

Energy Technology Data Exchange (ETDEWEB)

Bruhl, Jakob C., E-mail: jbruhl@purdue.edu; Varma, Amit H., E-mail: ahvarma@purdue.edu; Kim, Joo Min, E-mail: kim1493@purdue.edu

2015-12-15

Highlights: • An idealized static resistance function for SC walls is proposed. • The influence of design parameters on static resistance is explained. • SDOF models can accurately estimate global response of SC walls to missile impact. - Abstract: Steel-plate composite (SC) walls consist of a plain concrete core reinforced with two steel faceplates on the surfaces. Modules (consisting of steel faceplates, shear connectors and tie-bars) can be shop-fabricated and shipped to the site for erection and concrete casting, which expedites construction schedule and thus economy. SC structures have recently been used in nuclear power plant designs and are being considered for the next generation of small modular reactors. Design for impactive and impulsive loading is an important consideration for SC walls in safety-related nuclear facilities. The authors have previously developed design methods to prevent local failure (perforation) of SC walls due to missile impact. This paper presents the development of static resistance functions for use in single-degree-of-freedom (SDOF) analyses to predict the maximum displacement response of SC walls subjected to missile impact and designed to resist local failure (perforation). The static resistance function for SC walls is developed using results of numerical analyses and parametric studies conducted using benchmarked 3D finite element (FE) models. The influence of various design parameters are discussed and used to develop idealized bilinear resistance functions for SC walls with fixed edges and simply supported edges. Results from dynamic non-linear FE analysis of SC panels subjected to rigid missile impact are compared with the maximum displacements predicted by SDOF analyses using the bilinear resistance function.

Determination of Sc and Th in ScI3-NaI-ThI4 sample

International Nuclear Information System (INIS)

Yuan Hui; Yang Zhihong

1999-01-01

Determination of Sc and Th in ScI 3 -NaI-ThI 4 sample is studied by X-ray fluorescence and complexometry. The effect of working condition of Sc on X-ray fluorescence spectrometer and different sample-making method on the determination of Sc and Th are studied experimentally. The X-ray fluorescence analysis of determination of Sc and Th is developed by polyester film sample-making technique, the measuring precision of Sc and Th is better than 4%. The effect of acidity and temperature on the determining end point of titration is obvious. The results of different complexometric methods are compared. The precision of Sc and Th is less than 2% by comlexometry, it is fit for the routine analysis of ScI 3 -NaI-ThI 4 sample

An item-response theory approach to safety climate measurement: The Liberty Mutual Safety Climate Short Scales.

Science.gov (United States)

Huang, Yueng-Hsiang; Lee, Jin; Chen, Zhuo; Perry, MacKenna; Cheung, Janelle H; Wang, Mo

2017-06-01

Zohar and Luria's (2005) safety climate (SC) scale, measuring organization- and group- level SC each with 16 items, is widely used in research and practice. To improve the utility of the SC scale, we shortened the original full-length SC scales. Item response theory (IRT) analysis was conducted using a sample of 29,179 frontline workers from various industries. Based on graded response models, we shortened the original scales in two ways: (1) selecting items with above-average discriminating ability (i.e. offering more than 6.25% of the original total scale information), resulting in 8-item organization-level and 11-item group-level SC scales; and (2) selecting the most informative items that together retain at least 30% of original scale information, resulting in 4-item organization-level and 4-item group-level SC scales. All four shortened scales had acceptable reliability (≥0.89) and high correlations (≥0.95) with the original scale scores. The shortened scales will be valuable for academic research and practical survey implementation in improving occupational safety. Copyright © 2017 The Author(s). Published by Elsevier Ltd.. All rights reserved.

33 CFR 80.712 - Morris Island, SC to Hilton Head Island, SC.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Morris Island, SC to Hilton Head..., SC to Hilton Head Island, SC. (a) A line drawn from the easternmost tip of Folley Island to the... easternmost extremity of Hilton Head at latitude 32°13.0′ N. longitude 80°40.1′ W. [CGD 77-118a, 42 FR 35784...

Toxicity, tissue distribution and excretion of 46ScCl3 and 46Sc-EDTA in mice

International Nuclear Information System (INIS)

Lachine, E.E.; Noujaim, A.A.; Ediss, C.; Wiebe, L.I.

1976-01-01

The acute toxicity, differential distribution in tissue, and elimination of ScCl 3 , 46 ScCl 3 , Sc-EDTA and 46 Sc-EDTA, in mice, has been investigated. The LD 50 sup(24hr) doses for ScCl 3 were 440 and 24 mg kg -1 respectively after intraperitioneal and intravenous injection, and 720 and 108 mg kg -1 respectively for Sc-EDTA. 46 ScCl 3 was extensively deposited in the liver and the spleen. 46 Sc-EDTA was rapidly taken up by the kidney with subsequent elimation via the urine. While-body desaturation kinetics for 46 Sc-EDTA were found to fit a three compartmental model. The fast elimination phase (T1/2 = 12.75 min; K = 0.05540 min -1 ) accounted for 74.6% of the dose; the intermediate phase (T1/2 = 40.2 min; K = 0.01722 min -1 ) for 21.8%, and the slow (T1/2 = 5351 min; K = 0.00013 min -1 ) for 3.6% of the dose. (author)

Magnetic moment of {sup 48}Sc

Energy Technology Data Exchange (ETDEWEB)

Ohtsubo, T., E-mail: tohtsubo@np.gs.niigata-u.ac.jp; Kawamura, Y.; Ohya, S. [Niigata University, Department of Physics (Japan); Izumikawa, T. [Niigata University, Radioisotope Center (Japan); Nishimura, K. [Toyama University, Faculty of Engineering (Japan); Muto, S. [Neutron Science Laboratory, KEK (Japan); Shinozuka, T. [Tohoku University, Cyclotron and Radioisotope Center (Japan)

2007-11-15

Nuclear magnetic resonances were measured for {sup 48}Sc and {sup 44m}Sc oriented at 8 mK in an Fe host metal. The magnetic hyperfine splitting frequencies at an external magnetic field of 0.2 T were determined to be 63.22(11) MHz and 64.81(1) MHz for {sup 48}Sc and {sup 44m}Sc, respectively. With the known magnetic moment of {mu}({sup 44m}Sc)=+3.88 (1) {mu}{sub N}, the magnetic moment of {sup 48}Sc is deduced as {mu}({sup 44}Sc)=+3.785(12) {mu}{sub N}. The measured magnetic moment of {sup 48}Sc is discussed in terms of the shell model using the effective interactions.

4SC-202 activates ASK1-dependent mitochondrial apoptosis pathway to inhibit hepatocellular carcinoma cells

International Nuclear Information System (INIS)

Fu, Meili; Wan, Fuqiang; Li, Zhengling; Zhang, Fenghua

2016-01-01

The aim of the present study is to investigate the potential anti-hepatocellular carcinoma (HCC) cell activity by 4SC-202, a novel class I HDAC inhibitor (HDACi). The associated signaling mechanisms were also analyzed. We showed that 4SC-202 treatment induced potent cytotoxic and proliferation–inhibitory activities against established HCC cell lines (HepG2, HepB3, SMMC-7721) and patient-derived primary HCC cells. Further, adding 4SC-202 in HCC cells activated mitochondrial apoptosis pathway, which was evidenced by mitochondrial permeability transition pore (mPTP) opening, cytochrome C cytosol release and caspase-3/-9 activation. Inhibition of this apoptosis pathway, by caspase-3/-9 inhibitors, mPTP blockers, or by shRNA-mediated knockdown of cyclophilin-D (Cyp-D, a key component of mPTP), significantly attenuated 4SC-202-induced HCC cell death and apoptosis. Reversely, over-expression of Cyp-D enhanced 4SC-202's sensitivity in HCC cells. Further studies showed that 4SC-202 induced apoptosis signal-regulating kinase 1 (ASK1) activation, causing it translocation to mitochondria and physical association with Cyp-D. This mitochondrial ASK1-Cyp-D complexation appeared required for mediating 4SC-202-induced apoptosis activation. ASK1 stable knockdown by targeted-shRNAs largely inhibited 4SC-202-induced mPTP opening, cytochrome C release, and following HCC cell apoptotic death. Together, we suggest that 4SC-202 activates ASK1-dependent mitochondrial apoptosis pathway to potently inhibit human HCC cells. - Highlights: • 4SC-202 exerts potent anti-proliferative and cytotoxic activity against established/primary HCC cells. • SC-202-induced anti-HCC cell activity relies on caspase-dependent apoptosis activation. • 4SC-202 activates Cyp-D-dependent mitochondrial apoptosis pathway in HCC cells. • 4SC-202 activates ASK1 in HCC cells, causing it translocation to mitochondria. • Mitochondrial ASK1-Cyp-D complexation mediates 4SC-202's activity in HCC cells.

4SC-202 activates ASK1-dependent mitochondrial apoptosis pathway to inhibit hepatocellular carcinoma cells

Energy Technology Data Exchange (ETDEWEB)

Fu, Meili, E-mail: fumeilidrlinyi@tom.com [Department of Infectious Disease, Linyi People' s Hospital, Linyi 276000 (China); Wan, Fuqiang [Department of Head and Neck Surgery, Linyi Tumor Hospital, Linyi 276000 (China); Li, Zhengling [Department of Nursing, Tengzhou Central People' s Hospital, Tengzhou 277500 (China); Zhang, Fenghua [Department of Operating Room, Linyi People' s Hospital, Linyi 276000 (China)

2016-03-04

The aim of the present study is to investigate the potential anti-hepatocellular carcinoma (HCC) cell activity by 4SC-202, a novel class I HDAC inhibitor (HDACi). The associated signaling mechanisms were also analyzed. We showed that 4SC-202 treatment induced potent cytotoxic and proliferation–inhibitory activities against established HCC cell lines (HepG2, HepB3, SMMC-7721) and patient-derived primary HCC cells. Further, adding 4SC-202 in HCC cells activated mitochondrial apoptosis pathway, which was evidenced by mitochondrial permeability transition pore (mPTP) opening, cytochrome C cytosol release and caspase-3/-9 activation. Inhibition of this apoptosis pathway, by caspase-3/-9 inhibitors, mPTP blockers, or by shRNA-mediated knockdown of cyclophilin-D (Cyp-D, a key component of mPTP), significantly attenuated 4SC-202-induced HCC cell death and apoptosis. Reversely, over-expression of Cyp-D enhanced 4SC-202's sensitivity in HCC cells. Further studies showed that 4SC-202 induced apoptosis signal-regulating kinase 1 (ASK1) activation, causing it translocation to mitochondria and physical association with Cyp-D. This mitochondrial ASK1-Cyp-D complexation appeared required for mediating 4SC-202-induced apoptosis activation. ASK1 stable knockdown by targeted-shRNAs largely inhibited 4SC-202-induced mPTP opening, cytochrome C release, and following HCC cell apoptotic death. Together, we suggest that 4SC-202 activates ASK1-dependent mitochondrial apoptosis pathway to potently inhibit human HCC cells. - Highlights: • 4SC-202 exerts potent anti-proliferative and cytotoxic activity against established/primary HCC cells. • SC-202-induced anti-HCC cell activity relies on caspase-dependent apoptosis activation. • 4SC-202 activates Cyp-D-dependent mitochondrial apoptosis pathway in HCC cells. • 4SC-202 activates ASK1 in HCC cells, causing it translocation to mitochondria. • Mitochondrial ASK1-Cyp-D complexation mediates 4SC-202's activity in HCC cells.

Two studies evaluating the safety and immunogenicity of a live, attenuated Shigella flexneri 2a vaccine (SC602) and excretion of vaccine organisms in North American volunteers.

Science.gov (United States)

Katz, David E; Coster, Trinka S; Wolf, Marcia K; Trespalacios, Fernando C; Cohen, Dani; Robins, Guy; Hartman, Antoinette B; Venkatesan, Malabi M; Taylor, David N; Hale, Thomas L

2004-02-01

We report the first community-based evaluation of Shigella flexneri 2a strain SC602, a live, oral vaccine strain attenuated by deletion of the icsA (virG) plasmid virulence gene, given at 10(4) CFU. The primary objectives of this trial were to determine the safety and immunogenicity of the vaccine and to determine the duration of colonization. Four of 34 volunteers experienced transient fevers, and three reported diarrhea during the first 3 days of the study. Half of the volunteers mounted a positive serum immunoglobulin A (IgA) response to S. flexneri lipopolysaccharide. All but one of the volunteers excreted the vaccine in their stools for 1 to 33 days, and this excretion was often intermittent. Data from the community-based study were supplemented with an inpatient trial in which three volunteers received 10(3) and nine received 10(4) CFU. All volunteers who received 10(3) CFU excreted SC602 and had an IgA antibody-secreting cell response. Two of these had a serum IgA response. Six of the nine volunteers who received 10(4) CFU excreted SC602. One vaccinee had a transient fever and two met the definition of diarrhea. Six volunteers that received 10(4) CFU had an antibody-secreting cell response, and four had a serum IgA response. SC602 has now been tested at 10(4) CFU in a total of 58 volunteers. The cumulative results of these clinical trials, reported here and previously (Coster et al., Infect. Immun. 67:3437-3443, 1999), have demonstrated that SC602 is a substantially attenuated candidate vaccine that can evoke protection against the most severe symptoms of shigellosis in a stringent human challenge model of disease.

Topotactic oxidation pathway of ScTiO3 and high-temperature structure evolution of ScTiO3.5 and Sc4Ti3O12-type phases.

Science.gov (United States)

Shafi, Shahid P; Hernden, Bradley C; Cranswick, Lachlan M D; Hansen, Thomas C; Bieringer, Mario

2012-02-06

The novel oxide defect fluorite phase ScTiO(3.5) is formed during the topotactic oxidation of ScTiO(3) bixbyite. We report the oxidation pathway of ScTiO(3) and structure evolution of ScTiO(3.5), Sc(4)Ti(3)O(12), and related scandium-deficient phases as well as high-temperature phase transitions between room temperature and 1300 °Cusing in-situ X-ray diffraction. We provide the first detailed powder neutron diffraction study for ScTiO(3). ScTiO(3) crystallizes in the cubic bixbyite structure in space group Ia3 (206) with a = 9.7099(4) Å. The topotactic oxidation product ScTiO(3.5) crystallizes in an oxide defect fluorite structure in space group Fm3m (225) with a = 4.89199(5) Å. Thermogravimetric and differential thermal analysis experiments combined with in-situ X-ray powder diffraction studies illustrate a complex sequence of a topotactic oxidation pathway, phase segregation, and ion ordering at high temperatures. The optimized bulk synthesis for phase pure ScTiO(3.5) is presented. In contrast to the vanadium-based defect fluorite phases AVO(3.5+x) (A = Sc, In) the novel titanium analogue ScTiO(3.5) is stable over a wide temperature range. Above 950 °C ScTiO(3.5) undergoes decomposition with the final products being Sc(4)Ti(3)O(12) and TiO(2). Simultaneous Rietveld refinements against powder X-ray and neutron diffraction data showed that Sc(4)Ti(3)O(12) also exists in the defect fluorite structure in space group Fm3m (225) with a = 4.90077(4) Å. Sc(4)Ti(3)O(12) undergoes partial reduction in CO/Ar atmosphere to form Sc(4)Ti(3)O(11.69(2)).

CERN: SC-33

Energy Technology Data Exchange (ETDEWEB)

Anon.

1991-06-15

On 22 April a forward-looking CERN also looked back for a day, when the 'SC-33' event reviewed the achievements of CERN's first machine, the 600 MeV SynchroCyclotron (SC), which closed down on 17 December after 33 years of valiant service.

CERN: SC-33

International Nuclear Information System (INIS)

Anon.

1991-01-01

On 22 April a forward-looking CERN also looked back for a day, when the 'SC-33' event reviewed the achievements of CERN's first machine, the 600 MeV SynchroCyclotron (SC), which closed down on 17 December after 33 years of valiant service

S-C Mylonites

NARCIS (Netherlands)

Lister, G.S.; Snoke, A.W.

1984-01-01

Two types of foliations are commonly developed in mylonites and mylonitic rocks: (a) S-surfaces related to the accumulation of finite strain and (b) C-surfaces related to displacement discontinuities or zones of relatively high shear strain. There are two types of S-C mylonites. Type I S-C

Functional verification of a safety class controller for NPPs using a UVM register Model

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyu Chull [Dept. of Applied Computer Engineering, Dankook University, Cheonan (Korea, Republic of)

2014-06-15

A highly reliable safety class controller for NPPs (Nuclear Power Plants) is mandatory as even a minor malfunction can lead to disastrous consequences for people, the environment or the facility. In order to enhance the reliability of a safety class digital controller for NPPs, we employed a diversity approach, in which a PLC-type controller and a PLD-type controller are to be operated in parallel. We built and used structured testbenches based on the classes supported by UVM for functional verification of the PLD-type controller designed for NPPs. We incorporated a UVM register model into the testbenches in order to increase the controllability and the observability of the DUT(Device Under Test). With the increased testability, we could easily verify the datapaths between I/O ports and the register sets of the DUT, otherwise we had to perform black box tests for the datapaths, which is very cumbersome and time consuming. We were also able to perform constrained random verification very easily and systematically. From the study, we confirmed the various advantages of using the UVM register model in verification such as scalability, reusability and interoperability, and set some design guidelines for verification of the NPP controllers.

Determination of 46Sc in water

International Nuclear Information System (INIS)

Huo Bijun; Ji Zhaogang; Wang Juying

1985-01-01

Analytical procedures for the determination of 46 Sc in water is presented. 46 Sc in water is concentrated with Fe(OH) 3 ; Then 46 Sc is extracted with TBP and purified by precipitating it with Amygdalic Acid. Finally the precipitate is ignited into Sc 2 O 3 under 800 deg C and β-activity is counted. In this method chemical reeovery for Sc was (90.8 +- 2.8)% and radiochemical recovery for 46 Sc was (89.8 +- 3.8)%. Purification factors for some of the relevant Radionuclides ranged from 10 3 to 10 5

The effect of Sc additions on the microstructure and age hardening behaviour of as cast Al–Sc alloys

International Nuclear Information System (INIS)

Costa, S.; Puga, H.; Barbosa, J.; Pinto, A.M.P.

2012-01-01

Highlights: ► The Sc effect on the microstructure and ageing behaviour of Al–Sc alloys is studied. ► Cast into copper mould allows the elimination of solution heat treatment. ► Directly aged as cast alloys exhibits higher hardness and precipitation kinetics. ► Sc addition and optimised ageing result in an increase in Al–Sc mechanical properties. -- Abstract: The grain refinement effect and the ageing behaviour of Al–0.5 wt.% Sc, Al–0.7 wt.% Sc, and Al–1 wt.% Sc alloys are studied on the basis of optic microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) observations and hardness measurements. In Al–Sc alloys the higher grain refinement is observed for Sc contents greater than 0.5 wt.% accompanied by a notorious morphology modification, from coarse columnar grains to a fine perfect equiaxed structure. The as cast structures are characterised by a rich supersaturated solid solution in Sc, that promotes a great age hardening response at 250 °C and 300 °C. The age hardening curves also demonstrate a low overageing kinetics for all the alloys. Although the higher Sc content in solid solution for the alloys with 0.7 and 1 wt.% Sc, the age hardening response of all the Al–Sc alloys remains similar. The direct age hardening response of the as cast Al–0.5 wt.% Sc is shown to be greater than the solutionised and age hardened alloy.

PopSc: Computing Toolkit for Basic Statistics of Molecular Population Genetics Simultaneously Implemented in Web-Based Calculator, Python and R.

Science.gov (United States)

Chen, Shi-Yi; Deng, Feilong; Huang, Ying; Li, Cao; Liu, Linhai; Jia, Xianbo; Lai, Song-Jia

2016-01-01

Although various computer tools have been elaborately developed to calculate a series of statistics in molecular population genetics for both small- and large-scale DNA data, there is no efficient and easy-to-use toolkit available yet for exclusively focusing on the steps of mathematical calculation. Here, we present PopSc, a bioinformatic toolkit for calculating 45 basic statistics in molecular population genetics, which could be categorized into three classes, including (i) genetic diversity of DNA sequences, (ii) statistical tests for neutral evolution, and (iii) measures of genetic differentiation among populations. In contrast to the existing computer tools, PopSc was designed to directly accept the intermediate metadata, such as allele frequencies, rather than the raw DNA sequences or genotyping results. PopSc is first implemented as the web-based calculator with user-friendly interface, which greatly facilitates the teaching of population genetics in class and also promotes the convenient and straightforward calculation of statistics in research. Additionally, we also provide the Python library and R package of PopSc, which can be flexibly integrated into other advanced bioinformatic packages of population genetics analysis.

PopSc: Computing Toolkit for Basic Statistics of Molecular Population Genetics Simultaneously Implemented in Web-Based Calculator, Python and R.

Directory of Open Access Journals (Sweden)

Shi-Yi Chen

Full Text Available Although various computer tools have been elaborately developed to calculate a series of statistics in molecular population genetics for both small- and large-scale DNA data, there is no efficient and easy-to-use toolkit available yet for exclusively focusing on the steps of mathematical calculation. Here, we present PopSc, a bioinformatic toolkit for calculating 45 basic statistics in molecular population genetics, which could be categorized into three classes, including (i genetic diversity of DNA sequences, (ii statistical tests for neutral evolution, and (iii measures of genetic differentiation among populations. In contrast to the existing computer tools, PopSc was designed to directly accept the intermediate metadata, such as allele frequencies, rather than the raw DNA sequences or genotyping results. PopSc is first implemented as the web-based calculator with user-friendly interface, which greatly facilitates the teaching of population genetics in class and also promotes the convenient and straightforward calculation of statistics in research. Additionally, we also provide the Python library and R package of PopSc, which can be flexibly integrated into other advanced bioinformatic packages of population genetics analysis.

Solid-State NMR Spectroscopy Proves the Presence of Penta-coordinated Sc Sites in MIL-100(Sc).

Science.gov (United States)

Giovine, Raynald; Volkringer, Christophe; Ashbrook, Sharon E; Trébosc, Julien; McKay, David; Loiseau, Thierry; Amoureux, Jean-Paul; Lafon, Olivier; Pourpoint, Frédérique

2017-07-18

Advanced solid-state NMR methods and first-principles calculations demonstrate for the first time the formation of penta-coordinated scandium sites. These coordinatively unsaturated sites were shown during the thermal activation of scandium-based metal-organic frameworks (MOFs). A 45 Sc NMR experiment allows their specific observation in activated Sc 3 BTB 2 (H 3 BTB=1,3,5-tris(4-carboxyphenyl)benzene) and MIL-100(Sc) MOFs. The assignment of the ScO 5 groups is supported by the DFT calculations of NMR parameters. The presence of ScO 5 Lewis acid sites in MIL-100(Sc) explains furthermore its catalytic activity. The first NMR experiment to probe 13 C- 45 Sc distances is also introduced. This advanced solid-state NMR pulse sequence allows the demonstration of the shrinkage of the MIL-100(Sc) network when the activation temperature is raised. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Research on the evaluation model of the software reliability in nuclear safety class digital instrumentation and control system

International Nuclear Information System (INIS)

Liu Ying; Yang Ming; Li Fengjun; Ma Zhanguo; Zeng Hai

2014-01-01

In order to analyze the software reliability (SR) in nuclear safety class digital instrumentation and control system (D-I and C), firstly, the international software design standards were analyzed, the standards' framework was built, and we found that the D-I and C software standards should follow the NUREG-0800 BTP7-14, according to the NRC NUREG-0800 review of requirements. Secondly, the quantitative evaluation model of SR using Bayesian Belief Network and thirteen sub-model frameworks were established. Thirdly, each sub-models and the weight of corresponding indexes in the evaluation model were analyzed. Finally, the safety case was introduced. The models lay a foundation for review and quantitative evaluation on the SR in nuclear safety class D-I and C. (authors)

Infectivity-associated PrP(Sc) and disease duration-associated PrP(Sc) of mouse BSE prions.

Science.gov (United States)

Miyazawa, Kohtaro; Okada, Hiroyuki; Masujin, Kentaro; Iwamaru, Yoshifumi; Yokoyama, Takashi

2015-01-01

Disease-related prion protein (PrP(Sc)), which is a structural isoform of the host-encoded cellular prion protein, is thought to be a causative agent of transmissible spongiform encephalopathies. However, the specific role of PrP(Sc) in prion pathogenesis and its relationship to infectivity remain controversial. A time-course study of prion-affected mice was conducted, which showed that the prion infectivity was not simply proportional to the amount of PrP(Sc) in the brain. Centrifugation (20,000 ×g) of the brain homogenate showed that most of the PrP(Sc) was precipitated into the pellet, and the supernatant contained only a slight amount of PrP(Sc). Interestingly, mice inoculated with the obtained supernatant showed incubation periods that were approximately 15 d longer than those of mice inoculated with the crude homogenate even though both inocula contained almost the same infectivity. Our results suggest that a small population of fine PrP(Sc) may be responsible for prion infectivity and that large, aggregated PrP(Sc) may contribute to determining prion disease duration.

Flexural behavior and design of steel-plate composite (SC) walls for accident thermal loading

Energy Technology Data Exchange (ETDEWEB)

Booth, Peter N., E-mail: boothpn@purdue.edu [Lyles School of Civil Engineering, Purdue University, West Lafayette, IN (United States); Varma, Amit H., E-mail: ahvarma@purdue.edu [Lyles School of Civil Engineering, Purdue University, West Lafayette, IN (United States); Sener, Kadir C., E-mail: ksener@purdue.edu [Lyles School of Civil Engineering, Purdue University, West Lafayette, IN (United States); Malushte, Sanjeev R. [Bechtel Corp., Frederick, MD (United States)

2015-12-15

Modular steel-plate composite (SC) safety-related nuclear power plant structures must be designed to resist accident thermal and mechanical loads. The design accident thermal load represents the condition where high pressure and temperature steam is released as result of a mechanical failure and applied against the surfaces of power plant structural walls. The effect of heating and pressure can have both short and long term effects on the mechanical integrity of SC structures including degradation and cracking of concrete infill, residual stresses, and out-of-plane deformations. The purpose of this research is to study the effects of thermal and mechanical loads on the out-of-plane flexural response of SC walls and to develop simplified equations that can be used to predict behavior. Four experimental beam tests are reported that represent full-scale cross-sections of SC walls subjected to combinations of mechanical and thermal loads. The study determined that thermal loads reduce the out-of-plane flexural stiffness of SC walls. For the ambient condition, the flexural stiffness closely matches a conventional elastic cracked-transformed model, and at elevated temperatures, the stiffness is reduced to a fully-cracked flexural stiffness that only takes into account the stiffness of the steel faceplates. A method is presented for estimating the thermal curvature, ϕ{sub th}, and thermal moment, M{sub th}, resulting from unequal heating of opposing faces of an SC wall. Based on the tests in this study, the application of accident thermal loads did not result in a reduction of the flexural strength of the SC section.

SC tuning fork

CERN Document Server

The tuning fork used to modulate the radiofrequency system of the synchro cyclotron (SC) from 1957 to 1973. This piece is an unused spare part. The SC was the 1st accelerator built at CERN. It operated from August 1957 until it was closed down at the end of 1990. In the SC the magnetic field did not change with time, and the particles were accelerated in successive pulses by a radiofrequency voltage of some 20kV which varied in frequency as they spiraled outwards towards the extraction radius. The frequency varied from 30MHz to about 17Mz in each pulse. The tuning fork vibrated at 55MHz in vacuum in an enclosure which formed a variable capacitor in the tuning circuit of the RF system, allowing the RF to vary over the appropriate range to accelerate protons from the centre of the macine up to 600Mev at extraction radius. In operation the tips of the tuning fork blade had an amplitude of movement of over 1 cm. The SC accelerator underwent extensive improvements from 1973 to 1975, including the installation of a...

Measurement for commercial exposives with SC-DSC test. Sangyoyo bakuhayaku no SC-DSC sokutei

Energy Technology Data Exchange (ETDEWEB)

Yabashi, H.; Wada, Y.; Hwang, D.; Akutsu, Y.; Tamura, M.; Yoshida, T. (The University of Tokyo, Tokyo (Japan). Faculty of Engineering); Matsuzawa, T. (Nippon Kayaku Co. Ltd., Tokyo (Japan))

1991-08-30

The sealed cell differential scanning calorimetry (SC-DSC) was sintroduced of commercial blasting explosives. As a series of testing the commercial blasting explosives in performance, an SC-DSC test was made to compare the critical detonability line with that resulting therefrom. From the result of SC-DSC measurement, the critical dilution rate was estimated of commercial blasting explosives to become without detonating propagation. As a result, all the explosives with exception of ANFO one were assumed to have a possibility of detonating propagation so that the ANFO explosive was known to be material, unable to exactly evaluate the detonability by the SC-DSC test. The explosion heat, then calculated by the REITP2 in order to assume how the reaction proceeded in the DSC cell, was compared with the reaction heat measured by the SC-DSC test. As a result, the calculated value was known to be almost equal to or slightly larger than the measured one. 15 refs., 4 figs., 2 tabs.

α-ScVSe2O8, β-ScVSe2O8, and ScVTe2O8: new quaternary mixed metal oxides composed of only second-order Jahn-Teller distortive cations.

Science.gov (United States)

Kim, Yeong Hun; Lee, Dong Woo; Ok, Kang Min

2013-10-07

Three new quaternary scandium vanadium selenium/tellurium oxides, α-ScVSe2O8, β-ScVSe2O8, and ScVTe2O8 have been synthesized through hydrothermal and standard solid-state reactions. Although all three reported materials are stoichiometrically similar, they exhibit different crystal structures: α-ScVSe2O8 has a three-dimensional framework structure consisting of ScO6, VO6, and SeO3 groups. β-ScVSe2O8 reveals another three-dimensional framework composed of ScO7, VO5, and SeO3 polyhedra. ScVTe2O8 shows a layered structure with ScO6, VO4, and TeO4 polyhedra. Interestingly, the constituent cations, that is, Sc(3+), V(5+), Se(4+), and Te(4+) are all in a distorted coordination environment attributable to second-order Jahn-Teller (SOJT) effects. Complete characterizations including infrared spectroscopy, elemental analyses, thermal analyses, dipole moment calculation, and the magnitudes of out-of-center distortions for the compounds are reported. Transformation reactions suggest that α-ScVSe2O8 may change to β-ScVSe2O8, and then to Sc2(SeO3)3·H2O under hydrothermal conditions.

Structural changes and molecular interactions of hydrophobin SC3 in solution and on a hydrophobic surface

NARCIS (Netherlands)

Wang, X.; Vocht, M.L. de; Poolman, B.; Robillard, G.T.; Wang, [No Value; Jonge, J. de

2002-01-01

The hydrophobin SC3 belongs to a class of small proteins functioning in the growth and development of fungi. Its unique amphipathic property and remarkable surface activity make it interesting not only for biological studies but also for medical and industrial applications. Biophysical studies have

CERN Technical Training 2004: New Short Course III (SC III) on Microsoft Outlook - Meetings and Delegation

CERN Multimedia

Monique Duval

2004-01-01

The CERN Technical Training programme is now proposing a new format for courses on Microsoft Outlook. Three two-hours Short Courses (SC) cover basic and advanced functionalities of the recommended mail client for email at CERN. Each module can be followed independently. The next scheduled session of the 3rd module will take place as follows: Outlook (SC III): Meetings and Delegation. Next session: 9.11.2004 (14:00-16:00) SC III will cover how to organise and manage meetings, work with meeting requests, share tasks, and use email and calendar delegation. The number of participants to each session is limited to 8. The instructor is English-French bilingual, and she will be available some time after each session to answer specific questions, or provide further explanations following demand. The cost of attending any SC module on Outlook is 70.- CHF. The above session will be confirmed if there are enough participants, and the attendance costs will be lower in case of a full class. If you are interested in...

Study on safety classifications of software used in nuclear power plants and distinct applications of verification and validation activities in each class

International Nuclear Information System (INIS)

Kim, B. R.; Oh, S. H.; Hwang, H. S.; Kim, D. I.

2000-01-01

This paper describes the safety classification regarding instrumentation and control (I and C) systems and their software used in nuclear power plants, provides regulatory positions for software important to safety, and proposes verification and validation (V and V) activities applied differently in software classes which are important elements in ensuring software quality assurance. In other word, the I and C systems important to safety are classified into IC-1, IC-2, IC-3, and Non-IC and their software are classified into safety-critical, safety-related, and non-safety software. Based upon these safety classifications, the extent of software V and V activities in each class is differentiated each other. In addition, the paper presents that the software for use in I and C systems important to safety is divided into newly-developed and previously-developed software in terms of design and implementation, and provides the regulatory positions on each type of software

Probable variations of a passive safety containment for a 1700 MWe class PWR with passive safety systems

International Nuclear Information System (INIS)

Sato, Takashi; Fujiki, Yasunobu; Oikawa, Hirohide; Ofstun, Richard P.

2009-01-01

The paper presents probable variations of a passive safety containment for a PWR. The passive safety containment is named Mark P containment tentatively. It is a pressure suppression type containment for a large scale PWR with a BWR type passive containment cooling system (PCCS). More than 3-day grace period can be achieved even for a 1700 MWe class large scale PWR owing to the PCCS. The containment is a reinforced concrete containment vessel (RCCV). The design pressure of the RCCV can be low owing to the suppression pool (S/P) and no prestressed tendon is necessary. It is a single barrier CV that can withstand a large airplane crash by itself. This simple configuration results in good economy and short construction term. The BWR type passive safety systems also include the Passive Cooling and Depressurization System (PCDS). The PCDS has 3-day grace period for the SBO induced by a giant earthquake and can practically eliminate the residual risk of a giant earthquake beyond the design basis earthquake of Ss. It also has a safety function to automatically depressurize the primary system at accidents such as SGTR and eliminate the need for operator actions. It is a large 1700 MWe passive safety PWR that has more than 3-day grace period for extremely severe natural disasters including a giant earthquake, a mega hurricane, tsunami and so on; no containment failure at a SA establishing a no evacuation plant; protection for a large airplane crash with the RCCV single barrier; good economy and short construction term. (author)

An evaluation of safety culture initiatives at BNSF Railway

Science.gov (United States)

2015-04-01

Major safety culture (SC) initiatives initiated in the FRA Office of Research, Technology and Development (RT&D), such as Clear Signal for Action (CSA), the Investigation of Safety Related Occurrences Protocol (ISROP), the Participative Safety Rules ...

Seismic analysis of safety class 1 incinerator glovebox in building 232-Z 200 W Area

International Nuclear Information System (INIS)

Ocoma, E.C.

1994-09-01

This report documents the seismic evaluation for the existing safety class 1 incinerator glovebox in 232Z Building. The glovebox is no longer in use and most of the internal mechanical equipment have been removed. However, the insulation firebricks are still in the glovebox for proper disposal

Two anionically derivatized scandium oxoselenates(IV): ScF[SeO3] and Sc2O2[SeO3

Science.gov (United States)

Greiner, Stefan; Chou, Sheng-Chun; Schleid, Thomas

2017-02-01

Scandium fluoride oxoselenate(IV) ScF[SeO3] and scandium oxide oxoselenate(IV) Sc2O2[SeO3] could be synthesized through solid-state reactions. ScF[SeO3] was obtained phase-pure, by reacting mixtures of Sc2O3, ScF3 and SeO2 (molar ratio: 1:1:3) together with CsBr as fluxing agent in corundum crucibles embedded into evacuated glassy silica ampoules after firing at 700 °C for seven days. Sc2O2[SeO3] first emerged as by-product during the attempts to synthesize ScCl[SeO3] following aforementioned synthesis route and could later be reproduced from appropriate Sc2O3/SeO3 mixtures. ScF[SeO3] crystallizes monoclinically in space group P21/m with a=406.43(2), b =661.09(4), c=632.35(4) pm, β=93.298(3)° and Z=2. Sc2O2[SeO3] also crystallizes in the monoclinic system, but in space group P21/n with a=786.02(6), b=527.98(4), c=1086.11(8) pm, β=108.672(3)° for Z=4. The crystal structures of both compounds are strongly influenced by the stereochemically active lone pairs of the ψ1-tetrahedral [SeO3]2- anions. They also show partial structures, where the derivatizing F- or O2- anions play an important role. For ScF[SeO3] chains of the composition 2+∞ 1[FS c 2 / 2 ] form from connected [FSc2]5+ dumbbells, while [OSc3]7+ pyramids and [OSc4]10+ tetrahedra units are condensed to layers according to 2+ ∞ 2[O2Sc2 ] in Sc2O2[SeO3].

Compensation of native donor doping in ScN: Carrier concentration control and p-type ScN

Science.gov (United States)

Saha, Bivas; Garbrecht, Magnus; Perez-Taborda, Jaime A.; Fawey, Mohammed H.; Koh, Yee Rui; Shakouri, Ali; Martin-Gonzalez, Marisol; Hultman, Lars; Sands, Timothy D.

2017-06-01

Scandium nitride (ScN) is an emerging indirect bandgap rocksalt semiconductor that has attracted significant attention in recent years for its potential applications in thermoelectric energy conversion devices, as a semiconducting component in epitaxial metal/semiconductor superlattices and as a substrate material for high quality GaN growth. Due to the presence of oxygen impurities and native defects such as nitrogen vacancies, sputter-deposited ScN thin-films are highly degenerate n-type semiconductors with carrier concentrations in the (1-6) × 1020 cm-3 range. In this letter, we show that magnesium nitride (MgxNy) acts as an efficient hole dopant in ScN and reduces the n-type carrier concentration, turning ScN into a p-type semiconductor at high doping levels. Employing a combination of high-resolution X-ray diffraction, transmission electron microscopy, and room temperature optical and temperature dependent electrical measurements, we demonstrate that p-type Sc1-xMgxN thin-film alloys (a) are substitutional solid solutions without MgxNy precipitation, phase segregation, or secondary phase formation within the studied compositional region, (b) exhibit a maximum hole-concentration of 2.2 × 1020 cm-3 and a hole mobility of 21 cm2/Vs, (c) do not show any defect states inside the direct gap of ScN, thus retaining their basic electronic structure, and (d) exhibit alloy scattering dominating hole conduction at high temperatures. These results demonstrate MgxNy doped p-type ScN and compare well with our previous reports on p-type ScN with manganese nitride (MnxNy) doping.

Investigation of Sc(3) state in nonaqueous solutions by the 45Sc NMR method of high permission

International Nuclear Information System (INIS)

Buslaev, Yu.A.; Kirakosyan, G.A.; Tarasov, V.P.

1980-01-01

The ScCl 3 + CH 3 CN and ScCl 3 + KNCS + CH 3 CN solutions have been studied by a high-resolution NMR 45 Sc method. It has been estimated that in acetonitrile solutions, with competing ligands of Cl - and NCS - being available, hexacoordination Sc(3) complexes of various compositions are formed, and solvent molecules also take part in formation of the coordination sphere of scandium. Chemical shifts in NMR 45 Sc signals depend linearly on the number of chlor- or NCS - ions bound to scandium(3). This made it possible to determine the value of chemical shifts in signals of all 28 potential complexes formed in a system with three competing ligands

Development of standardized radioactive 46Sc solution

International Nuclear Information System (INIS)

Du Hongshan; Jia Zhang; Yu Yiguang; Sun Naiyao

1988-01-01

A method of preparation of standardized radioactive 46 Sc solution is developed. The separation of 46 Sc, the composition of 46 Sc solution and its stability, and radioactivity measurement of 46 Sc are systematically studied. The results obtained in the study and in the applications in many laboratories have shown that our method is effective and reliable

Method to classify the safety class of Structure, System and Components in a Defueled Condition of Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Kim, Dong-Hak; Jeon, Dang-Hee [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

During pre-decommissioning phase, licensing and engineering work need to change the design basis of the plant such as safety analysis report, downgrade of systems, technical specifications and program and procedures to change of NPP condition from in an operation condition to in a defueled condition. The many systems to need to operate in an operational condition will not be operated during in a defueled condition and the function of systems will be changed from in an operation condition to in a defueled condition. So a downgrade of systems may be needed and reclassifying the safety class of structure, system and component (SSC) may be conducted. By the reclassification of SSC, activity related with quality assurance and maintenance of SSC is affected. In this paper, the method to reclassify SSC in a defueled condition is studied. The many systems to need to operate in an operational condition will not be operated during in a defueled condition and the function of systems will be changed from in an operation condition to in a defueled condition. The operation of NPP during a defueled condition need to conduct licensing and engineering work need to change the design basis of the plant optimize by downgrading systems and reclassifying the safety class of SSC. In this paper, the method to reclassify safety class for a defueled condition is studied.

SC-FDMA for mobile communications

CERN Document Server

Abd El-Samie, Fathi E

2013-01-01

SC-FDMA for Mobile Communications examines Single-Carrier Frequency Division Multiple Access (SC-FDMA). Explaining this rapidly evolving system for mobile communications, it describes its advantages and limitations and outlines possible solutions for addressing its current limitations. The book explores the emerging trend of cooperative communication with SC-FDMA and how it can improve the physical layer security. It considers the design of distributed coding schemes and protocols for wireless relay networks where users cooperate to send their data to the destination. Supplying you with the re

A safety equipment list for rotary mode core sampling systems operation in single shell flammable gas tanks

International Nuclear Information System (INIS)

SMALLEY, J.L.

1999-01-01

This document identifies all interim safety equipment to be used for rotary mode core sampling of single-shell flammable gas tanks utilizing Rotary Mode Core Sampling systems (RMCS). This document provides the safety equipment for RMCS trucks HO-68K-4600, HO-68K-4647, trucks three and four respectively, and associated equipment. It is not intended to replace or supersede WHC-SD-WM-SEL-023, (Kelly 1991), or WHC-SD-WM-SEL-032, (Corbett 1994), which classifies 80-68K-4344 and HO-68K-4345 respectively. The term ''safety equipment'' refers to safety class (SC) and safety significant (SS) equipment, where equipment refers to structures, systems and components (SSC's). The identification of safety equipment in this document is based on the credited design safety features and analysis contained in the Authorization Basis (AB) for rotary mode core sampling operations in single-shell flammable gas tanks. This is an interim safety classification since the AB is interim. This document will be updated to reflect the final RMCS equipment safety classification designations upon completion of a final AB which will be implemented with the release of the Final Safety Analysis Report (FSAR)

Precipitation in cold-rolled Al-Sc-Zr and Al-Mn-Sc-Zr alloys prepared by powder metallurgy

KAUST Repository

Vlach, Martin

2013-12-01

The effects of cold-rolling on thermal, mechanical and electrical properties, microstructure and recrystallization behaviour of the AlScZr and AlMnScZr alloys prepared by powder metallurgy were studied. The powder was produced by atomising in argon with 1% oxygen and then consolidated by hot extrusion at 350 C. The electrical resistometry and microhardness together with differential scanning calorimetry measurements were compared with microstructure development observed by transmission and scanning electron microscopy, X-ray diffraction and electron backscatter diffraction. Fine (sub)grain structure developed and fine coherent Al3Sc and/or Al3(Sc,Zr) particles precipitated during extrusion at 350 C in the alloys studied. Additional precipitation of the Al3Sc and/or Al3(Sc,Zr) particles and/or their coarsening was slightly facilitated by the previous cold rolling. The presence of Sc,Zr-containing particles has a significant antirecrystallization effect that prevents recrystallization at temperatures minimally up to 420 C. The precipitation of the Al6Mn- and/or Al 6(Mn,Fe) particles of a size ~ 1.0 μm at subgrain boundaries has also an essential antirecrystallization effect and totally suppresses recrystallization during 32 h long annealing at 550 C. The texture development of the alloys seems to be affected by high solid solution strengthening by Mn. The precipitation of the Mn-containing alloy is highly enhanced by a cold rolling. The apparent activation energy of the Al3Sc particles formation and/or coarsening and that of the Al6Mn and/or Al 6(Mn,Fe) particle precipitation in the powder and in the compacted alloys were determined. The cold deformation has no effect on the apparent activation energy values of the Al3Sc-phase and the Al 6Mn-phase precipitation. © 2013 Elsevier Inc.

Precipitation in cold-rolled Al-Sc-Zr and Al-Mn-Sc-Zr alloys prepared by powder metallurgy

KAUST Repository

Vlach, Martin; Stulí ková , Ivana; Smola, Bohumil; Kekule, Tomá š; Kudrnová , Hana; Daniš, Stanislav; Gemma, Ryota; Očená šek, Vladivoj; Má lek, Jaroslav; Tanprayoon, Dhritti; Neubert, Volkmar

2013-01-01

The effects of cold-rolling on thermal, mechanical and electrical properties, microstructure and recrystallization behaviour of the AlScZr and AlMnScZr alloys prepared by powder metallurgy were studied. The powder was produced by atomising in argon with 1% oxygen and then consolidated by hot extrusion at 350 C. The electrical resistometry and microhardness together with differential scanning calorimetry measurements were compared with microstructure development observed by transmission and scanning electron microscopy, X-ray diffraction and electron backscatter diffraction. Fine (sub)grain structure developed and fine coherent Al3Sc and/or Al3(Sc,Zr) particles precipitated during extrusion at 350 C in the alloys studied. Additional precipitation of the Al3Sc and/or Al3(Sc,Zr) particles and/or their coarsening was slightly facilitated by the previous cold rolling. The presence of Sc,Zr-containing particles has a significant antirecrystallization effect that prevents recrystallization at temperatures minimally up to 420 C. The precipitation of the Al6Mn- and/or Al 6(Mn,Fe) particles of a size ~ 1.0 μm at subgrain boundaries has also an essential antirecrystallization effect and totally suppresses recrystallization during 32 h long annealing at 550 C. The texture development of the alloys seems to be affected by high solid solution strengthening by Mn. The precipitation of the Mn-containing alloy is highly enhanced by a cold rolling. The apparent activation energy of the Al3Sc particles formation and/or coarsening and that of the Al6Mn and/or Al 6(Mn,Fe) particle precipitation in the powder and in the compacted alloys were determined. The cold deformation has no effect on the apparent activation energy values of the Al3Sc-phase and the Al 6Mn-phase precipitation. © 2013 Elsevier Inc.

Band structure of the quaternary Heusler alloys ScMnFeSn and ScFeCoAl

Science.gov (United States)

Shanthi, N.; Teja, Y. N.; Shaji, Shephine M.; Hosamani, Shashikala; Divya, H. S.

2018-04-01

In our quest for materials with specific applications, a theoretical study plays an important role in predicting the properties of compounds. Heusler alloys or compounds are the most studied in this context. More recently, a lot of quaternary Heusler compounds are investigated for potential applications in fields like Spintronics. We report here our preliminary study of the alloys ScMnFeSn and ScFeCoAl, using the ab-initio linear muffin-tin orbital method within the atomic sphere approximation (LMTO-ASA). The alloy ScMnFeSn shows perfect half-metallicity, namely, one of the spins shows a metallic behaviour and the other spin shows semi-conducting behaviour. Such materials find application in devices such as the spin-transfer torque random access memory (STT-MRAM). In addition, the alloy ScMnFeSn is found to have an integral magnetic moment of 4 µB, as predicted by the Slater-Pauling rule. The alloy ScFeCoAl does not show half-metallicity.

Archform comparisons between skeletal class II and III malocclusions.

Directory of Open Access Journals (Sweden)

Wei Zou

Full Text Available The purpose of this cross-sectional research was to explore the relationship of the mandibular dental and basal bone archforms between severe Skeletal Class II (SC2 and Skeletal Class III (SC3 malocclusions. We also compared intercanine and intermolar widths in these two malocclusion types. Thirty-three virtual pretreatment mandibular models (Skeletal Class III group and Thirty-five Skeletal Class II group pretreatment models were created with a laser scanning system. FA (the midpoint of the facial axis of the clinical crownand WALA points (the most prominent point on the soft-tissue ridgewere employed to produce dental and basal bone archforms, respectively. Gained scatter diagrams of the samples were processed by nonlinear regression analysis via SPSS 17.0. The mandibular dental and basal bone intercanine and intermolar widths were significantly greater in the Skeletal Class III group compared to the Skeletal Class II group. In both groups, a moderate correlation existed between dental and basal bone arch widths in the canine region, and a high correlation existed between dental and basal bone arch widths in the molar region. The coefficient of correlation of the Skeletal Class III group was greater than the Skeletal Class II group. Fourth degree, even order power functions were used as best-fit functions to fit the scatter plots. The radius of curvature was larger in Skeletal Class III malocclusions compared to Skeletal Class II malocclusions (rWALA3>rWALA2>rFA3>rFA2. In conclusion, mandibular dental and basal intercanine and intermolar widths were significantly different between the two groups. Compared with Skeletal Class II subjects, the mandibular archform was more flat for Skeletal Class III subjects.

A safety equipment list for rotary mode core sampling systems operation in single shell flammable gas tanks; TOPICAL

International Nuclear Information System (INIS)

SMALLEY, J.L.

1999-01-01

This document identifies all interim safety equipment to be used for rotary mode core sampling of single-shell flammable gas tanks utilizing Rotary Mode Core Sampling systems (RMCS). This document provides the safety equipment for RMCS trucks HO-68K-4600, HO-68K-4647, trucks three and four respectively, and associated equipment. It is not intended to replace or supersede WHC-SD-WM-SEL-023, (Kelly 1991), or WHC-SD-WM-SEL-032, (Corbett 1994), which classifies 80-68K-4344 and HO-68K-4345 respectively. The term ''safety equipment'' refers to safety class (SC) and safety significant (SS) equipment, where equipment refers to structures, systems and components (SSC's). The identification of safety equipment in this document is based on the credited design safety features and analysis contained in the Authorization Basis (AB) for rotary mode core sampling operations in single-shell flammable gas tanks. This is an interim safety classification since the AB is interim. This document will be updated to reflect the final RMCS equipment safety classification designations upon completion of a final AB which will be implemented with the release of the Final Safety Analysis Report (FSAR)

Development of nuclear safety class filter elements with long life and high quality

International Nuclear Information System (INIS)

Zhang Jinghua

2009-04-01

This paper describes the development on nuclear safety class filter elements with long life and high quality used for collecting radioactive contaminants, fragments of resin and impurities in primary systems of NPPs. The filter elements made of glass fibre elements are used for PWR, and of paper elements are used for PHWR. During the research, a series of tests for optimization were performed for selection of filter material and the improvement of binder. The flow rate and comprehensive performance have been measured in simulated conditions. The result shows that the application requirements for operational NPPs can be met, and the reliability and safety of the frame are also be verified. The comprehensive performance of the filter elements is equivalent to that of oversea similar products. The products have been used in NPPs in operation. (authors)

Proposal for the improvement of IRD safety culture based on risk analysis

International Nuclear Information System (INIS)

Aguiar, L.A.; Ferreira, P.R.R.; Silveira, C.S.

2017-01-01

The Safety Culture (SC) is a concept about the relationship of individuals and organizations towards the safety in a specific activity. Any organization that carries out activities with risks has a SC, even at minimum levels. People perceive different types of radiation risks in very different ways, therefore, to identify and to analysis of the possible radiation risks resulting from normal operation or accident conditions is an important issue in order to improve the SC in organization. The main is to present guidelines for the improvement of the safety culture in the Institute of Radiation Protection and Dosimetry - IRD through on risk-based approach. The methodology proposed here is: A) select a division of the IRD for case study; B) assess the level of the 10 culture safety basic elements of the IRD division selected; C) conduct a survey of the hazards and risks associated with the various activities developed by the division; D) reassess the level of the 10 basic elements of CS; And E) analyze the results and correlate the impact of risk knowledge on safety culture improvement. The expected result is improvement the safety and of safety culture by understanding of radiation risks and hazards relating to work and to the working environment; and thus enforce a collective commitment to safety by teams and individuals and raise the safety culture to higher levels. (author)

Proposal for the improvement of IRD safety culture based on risk analysis

Energy Technology Data Exchange (ETDEWEB)

Aguiar, L.A.; Ferreira, P.R.R. [Instituto de Radioproteção e Dosimetria (DIRAD/IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Silveira, C.S., E-mail: laguiar@ird.gov.br [Comissão Nacional de Energia Nuclear (DRS/CGMI/CNEN), Rio de Janeiro, RJ (Brazil)

2017-07-01

The Safety Culture (SC) is a concept about the relationship of individuals and organizations towards the safety in a specific activity. Any organization that carries out activities with risks has a SC, even at minimum levels. People perceive different types of radiation risks in very different ways, therefore, to identify and to analysis of the possible radiation risks resulting from normal operation or accident conditions is an important issue in order to improve the SC in organization. The main is to present guidelines for the improvement of the safety culture in the Institute of Radiation Protection and Dosimetry - IRD through on risk-based approach. The methodology proposed here is: A) select a division of the IRD for case study; B) assess the level of the 10 culture safety basic elements of the IRD division selected; C) conduct a survey of the hazards and risks associated with the various activities developed by the division; D) reassess the level of the 10 basic elements of CS; And E) analyze the results and correlate the impact of risk knowledge on safety culture improvement. The expected result is improvement the safety and of safety culture by understanding of radiation risks and hazards relating to work and to the working environment; and thus enforce a collective commitment to safety by teams and individuals and raise the safety culture to higher levels. (author)

Discussion on the safety classification of nuclear safety mechanical equipment

International Nuclear Information System (INIS)

Shen Wei

2010-01-01

The purpose and definition of the equipment safety classification in nuclear plant are introduced. The differences of several safety classification criterions are compared, and the object of safety classification is determined. According to the regulation, the definition and category of the safety functions are represented. The safety classification method, safety classification process, safety class interface, and the requirement for the safety class mechanical equipment are explored. At last, the relation of the safety classification between the mechanical and electrical equipment is presented, and the relation of the safety classification between mechanical equipment and system is also presented. (author)

The Development of the Safety Related Valve Class 1E Electrical Motor, the Target and the Results

International Nuclear Information System (INIS)

Saban, I.; Grgic, D.; Fancev, T.; Flegar, Lj.; Novosel, N.

1996-01-01

The development of the safety related valves class 1E electric motor is described. The design implemented in order to satisfy the 1E requirements, and a way in which related 1E standards are addressed, are shown. The development was realized in three stages. In the first stage eight motorettes were made and the insulation system was tested. In the second stage the motor was produced in accordance with producer's prototype QA program. In the third stage part of the testing of the produced motor was made. The results of the testing, finished until now, show that produced motor, as well as similarly produced motors, is able to perform its safety function in the design bases accident conditions as requested by class 1E requirements. The rest of the testing (LOCA test) can be made on the same or similar motor in the future. (author)

An overview on development of safety culture of regulatory body in Korea

International Nuclear Information System (INIS)

Yoon, Myunghyun; Choi, Young Sung; Yi, Kyungjoo

2015-01-01

Fukushima accident revealed not only licensees but also regulatory bodies' (RBs) establishment of robust safety culture (SC) is crucial to implement effective safety regulation. Result of the IAEA IRRS held in 2011 required regulatory body in Korea to make improvement measure for the enhancement of safety culture of regulatory body (SCRB). Compared to works done to assess SC focused on working organizations of nuclear industry, not enough attention has been paid to assess the RBs. To achieve this goal, long-term comprehensive drive plan has to be made. The IAEA is putting great effort to establish and enhance SC in RBs. OECD/NEA CNRA is planning to produce Green Booklet on SCRB for regulatory guidance. SCRB is an organization's culture, RBs ultimately has to possess in order to assure secure use of nuclear energy. An organization's culture emerges from, and is manifested in, the interplay of its members' emotion, cognition, attitudes, behaviors and interaction patterns. As a result of this mechanism, organizational structures and culture influence individual's attitude and behavior when entered into a situation. Each organization has its strengths and weakness in SC. Safety culture defective components of the Fukushima accident was analyzed by JNES in 2012. According to the casual factors indicated in the investigation report, Nuclear Regulatory Organizations (NROs) of Korea also had weakness of the SCRB in terms of questioning attitude, continuous learning, issue identification and resolution and safety leadership. It doesn't have to be same but necessary for both NSSC and KINS to be consistent in building SC traits to carry out a coherent policy with synergy effect. NROs should communicated and convey consistent message to the stakeholders. Not limited to development of SCRB itself, influence of SCRB on licensee's SC is recommended for further study. Also, what behaviors are expected to make positive effects and whether they can

An overview on development of safety culture of regulatory body in Korea

Energy Technology Data Exchange (ETDEWEB)

Yoon, Myunghyun; Choi, Young Sung; Yi, Kyungjoo [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2015-10-15

Fukushima accident revealed not only licensees but also regulatory bodies' (RBs) establishment of robust safety culture (SC) is crucial to implement effective safety regulation. Result of the IAEA IRRS held in 2011 required regulatory body in Korea to make improvement measure for the enhancement of safety culture of regulatory body (SCRB). Compared to works done to assess SC focused on working organizations of nuclear industry, not enough attention has been paid to assess the RBs. To achieve this goal, long-term comprehensive drive plan has to be made. The IAEA is putting great effort to establish and enhance SC in RBs. OECD/NEA CNRA is planning to produce Green Booklet on SCRB for regulatory guidance. SCRB is an organization's culture, RBs ultimately has to possess in order to assure secure use of nuclear energy. An organization's culture emerges from, and is manifested in, the interplay of its members' emotion, cognition, attitudes, behaviors and interaction patterns. As a result of this mechanism, organizational structures and culture influence individual's attitude and behavior when entered into a situation. Each organization has its strengths and weakness in SC. Safety culture defective components of the Fukushima accident was analyzed by JNES in 2012. According to the casual factors indicated in the investigation report, Nuclear Regulatory Organizations (NROs) of Korea also had weakness of the SCRB in terms of questioning attitude, continuous learning, issue identification and resolution and safety leadership. It doesn't have to be same but necessary for both NSSC and KINS to be consistent in building SC traits to carry out a coherent policy with synergy effect. NROs should communicated and convey consistent message to the stakeholders. Not limited to development of SCRB itself, influence of SCRB on licensee's SC is recommended for further study. Also, what behaviors are expected to make positive effects and whether they can

Saccharomyces cerevisiae Differential Functionalization of Presumed ScALT1 and ScALT2 Alanine Transaminases Has Been Driven by Diversification of Pyridoxal Phosphate Interactions

Directory of Open Access Journals (Sweden)

Erendira Rojas-Ortega

2018-05-01

Full Text Available Saccharomyces cerevisiae arose from an interspecies hybridization (allopolyploidiza-tion, followed by Whole Genome Duplication. Diversification analysis of ScAlt1/ScAlt2 indicated that while ScAlt1 is an alanine transaminase, ScAlt2 lost this activity, constituting an example in which one of the members of the gene pair lacks the apparent ancestral physiological role. This paper analyzes structural organization and pyridoxal phosphate (PLP binding properties of ScAlt1 and ScAlt2 indicating functional diversification could have determined loss of ScAlt2 alanine transaminase activity and thus its role in alanine metabolism. It was found that ScAlt1 and ScAlt2 are dimeric enzymes harboring 67% identity and intact conservation of the catalytic residues, with very similar structures. However, tertiary structure analysis indicated that ScAlt2 has a more open conformation than that of ScAlt1 so that under physiological conditions, while PLP interaction with ScAlt1 allows the formation of two tautomeric PLP isomers (enolimine and ketoenamine ScAlt2 preferentially forms the ketoenamine PLP tautomer, indicating a modified polarity of the active sites which affect the interaction of PLP with these proteins, that could result in lack of alanine transaminase activity in ScAlt2. The fact that ScAlt2 forms a catalytically active Schiff base with PLP and its position in an independent clade in “sensu strictu” yeasts suggests this protein has a yet undiscovered physiological function.

Saccharomyces cerevisiae Differential Functionalization of Presumed ScALT1 and ScALT2 Alanine Transaminases Has Been Driven by Diversification of Pyridoxal Phosphate Interactions

Science.gov (United States)

Rojas-Ortega, Erendira; Aguirre-López, Beatriz; Reyes-Vivas, Horacio; González-Andrade, Martín; Campero-Basaldúa, Jose C.; Pardo, Juan P.; González, Alicia

2018-01-01

Saccharomyces cerevisiae arose from an interspecies hybridization (allopolyploidiza-tion), followed by Whole Genome Duplication. Diversification analysis of ScAlt1/ScAlt2 indicated that while ScAlt1 is an alanine transaminase, ScAlt2 lost this activity, constituting an example in which one of the members of the gene pair lacks the apparent ancestral physiological role. This paper analyzes structural organization and pyridoxal phosphate (PLP) binding properties of ScAlt1 and ScAlt2 indicating functional diversification could have determined loss of ScAlt2 alanine transaminase activity and thus its role in alanine metabolism. It was found that ScAlt1 and ScAlt2 are dimeric enzymes harboring 67% identity and intact conservation of the catalytic residues, with very similar structures. However, tertiary structure analysis indicated that ScAlt2 has a more open conformation than that of ScAlt1 so that under physiological conditions, while PLP interaction with ScAlt1 allows the formation of two tautomeric PLP isomers (enolimine and ketoenamine) ScAlt2 preferentially forms the ketoenamine PLP tautomer, indicating a modified polarity of the active sites which affect the interaction of PLP with these proteins, that could result in lack of alanine transaminase activity in ScAlt2. The fact that ScAlt2 forms a catalytically active Schiff base with PLP and its position in an independent clade in “sensu strictu” yeasts suggests this protein has a yet undiscovered physiological function. PMID:29867852

The ternary systems Sc-Sm(Dy)-Si at 870 K

International Nuclear Information System (INIS)

Kotur, B.Ya.; Mokra, I.Ya.; Toporinskij, A.Ya.

1991-01-01

Isothermal cross sections of the ternary systems Sc-Sm-Si and Sc-Dy-Si at 870 K have been plotted. Investigation of scandium and disprosium in ternary systems have been examined by X-ray diffraction and microstructure analysis. Besides literary data on binary systems Sc-Si, Sm-Si, Dy-Si have been used. Formation of limited (Sc-Sm-Si, Sc-Dy-Si) and continuous (Sc-Dy-Si) solid solutions based on bisilicides of Sc and Sm(Dy) is discovered. Two and five ternary compounds in Sc-Sm-Si and Sc-Dy-Si systems have been determined and their crystal structure has been established. When investigating of Sc-(rare earth element)-Si ternary systems and should take into account the specific interaction of scandium and samarium with REE

The role of the regulator in promoting and evaluating safety culture. Operating experience feedback programme approach

International Nuclear Information System (INIS)

Perez, S.

2002-01-01

Promoting and Evaluating Safety Culture (S.C.) in Operating Organizations must be one of the main Nuclear Regulator goals to achieve. This can be possible only if each and every one of the regulatory activities inherently involves S.C. It can be seen throughout attitudes, values, uses and practices in both individuals and the whole regulatory organization. One among all the regulatory tools commonly used by regulators to promote and evaluate the commitment of the licensees with safety culture as a whole involves organizational factors and particular attention is directed to the operating organization. This entailed a wide range of activities, including all those related with management of safety performance. Operating Experience Feedback Programme as a tool to enhance safety operation is particularly useful for regulators in the evaluation of the role of S.C. in operating organization. Safety Culture is recognized as a subset of the wider Organizational Culture. Practices that improve organizational effectiveness can also contribute to enhance safety. An effective event investigation methodology is a specific practice, which contributes to a healthy Safety Culture. (author)

Hydride vapor phase epitaxy growth of GaN, InGaN, ScN, and ScAIN

NARCIS (Netherlands)

Bohnen, T.

2010-01-01

Chemical vapor deposition (CVD); hydride vapor phase epitaxy (HVPE); gallium nitride (GaN); indium gallium nitride (InGaN); scandium nitride (ScN); scandium aluminum nitride (ScAlN); semiconductors; thin films; nanowires; III nitrides; crystal growth - We studied the HVPE growth of different III

Block-Iterative Frequency-Domain Equalizations for SC-IDMA Systems

Directory of Open Access Journals (Sweden)

Salah Awad Salman

2015-07-01

Full Text Available In wireless broadband communications using single-carrier interleave division multiple access (SC-IDMA systems, efficient multiuser detection (MUD classes that make use of joint hybrid decision feedback equalization (HDFE/ frequency decision-feedback equalization (FDFE and interference cancellation (IC techniques, are proposed in conjunction with channel coding to deal with several users accessing the multipath fading channels. In FDFE-IDMA, the feedforward (FF and feedback (FB filtering operations of FDFE, which use to remove intersymbol interference (ISI, are implemented by Fast Fourier Transforms (FFTs, while in HDFE-IDMA the only FF filter is implemented by FFTs. Further, the parameters involved in the FDFE/HDFE filtering are derived according to the minimum mean square error (MMSE criteria, and the feedback symbol decisions are directly designed from soft detection of the decoded signals at the previous iteration. The simulation results including comparisons with those of frequency domain equalization (FDE, SC-FDE-IDMA and multi-carrier OFDM-IDMA schemes, with cyclic prefixing (CP and zero padding (ZP techniques, show that the combination of FDFE-IC/HDFE-IC provides an efficient solution with good performance for IDMA systems in ISI channels. Moreover, these iterative structures with block equalization yield a much lower complexity than equivalent existing structures, making them attractive for a wealth of applications.

Ultimate internal pressure capacity assessment of SC structure

International Nuclear Information System (INIS)

Park, Hyungkui; Choi, Inkil

2013-01-01

An SC structure applied to a containment building can be quite effective. However, an SC structure cannot be applied to a containment building, because its internal pressure resistance performance has not been verified. The containment building, which undergoes ultimate internal pressure, resists the internal pressure through a pre-stress tendon. It is hard to apply a tendon to an SC structure because of its structural characteristics. Therefore, the internal pressure resistance performance of the SC structure itself should be ensured to apply it to a structure with internal pressure resistance. In this study, the suitability of an SC structure as a substitution for the tendon of a pressure resistant structure was evaluated. A containment structure model was used in this study, because it was representative structures that resistance of ultimate internal pressure be required. In this study, a nonlinear analysis was performed to evaluate and compare the behaviors of tendon model and SC structure model. By comparing the internal pressure-displacement according to the structure type, the stability of SC structure model was assessed

Seismic qualification of safety class components in non-reactor nuclear facilities at Hanford site

International Nuclear Information System (INIS)

Ocoma, E.C.

1989-01-01

This paper presents the methods used during the walkdowns to compile as-built structural information to seismically qualify or verify the seismic adequacy of safety class components in the Plutonium Finishing Plant complex. The Plutonium finishing Plant is a non-reactor nuclear facility built during the 1950's and was designed to the Uniform Building Code criteria for both seismic and wind events. This facility is located at the US Department of Energy Hanford Site near Richland, Washington

Ab-initio studies of the Sc adsorption and the ScN thin film formation on the GaN(000-1)-(2 × 2) surface

International Nuclear Information System (INIS)

Guerrero-Sánchez, J.; Sánchez-Ochoa, F.; Cocoletzi, Gregorio H.; Rivas-Silva, J.F.; Takeuchi, Noboru

2013-01-01

First principles total energy calculations have been performed to investigate the initial stages of the Sc adsorption and ScN thin film formation on the GaN(000-1)-(2 × 2) surface. Studies are done within the periodic density functional theory as implemented in the PWscf code of the Quantum ESPRESSO package. The Sc adsorption at high symmetry sites results in the bridge site as the most stable structure. When a Sc monolayer is deposited above the surface the T4 site results as the most stable geometry. The Sc migration into the first Ga monolayer induces the Ga displaced ad-atom to be adsorbed at the T4-2 site. A ScN bilayer may be obtained under the Ga monolayer. Finally a ScN bilayer may be formed in the wurtzite phase above the surface. The formation energy plots show that in the moderate Ga-rich conditions we obtain the formation of a ScN bilayer under the gallium monolayer. However at N-rich conditions the formation of ScN bilayer above the surface is the most favorable structure. We report the density of states to explain the electronic structure of the most favorable geometries. - Highlights: • Studies of the initial stages in the formation of Sc and ScN structures on GaN • In the adsorption of Sc on the GaN the Br site is the most favorable geometry. • When a Sc replaces a Ga of the first monolayer the displaced Ga occupies a T4-2 site. • For Ga-rich conditions there is formation of ScN under the Ga monolayer. • In N-rich conditions there is formation of ScN in the wurtzite phase

Nuclear safety review for qualification of class 1E motor inside containment for nuclear power stations

International Nuclear Information System (INIS)

Li Shixin; Wu Qi; Zhang Yunbo; Wu Caixia

2013-01-01

In nuclear power plants with pressurized water reactors, the review for class 1E motor inside containment qualification process and documents is an important aspect of nuclear safety equipment review, and the reviewers should make evaluations for the qualification test results in terms of the compliance with standard and regulation, and the consistency with inside containment environment. Firstly, this paper introduces the qualification test of class 1E motor inside containment for nuclear power generating stations, such as aging test and design-basis-event test. Second, there is a discussion about typical problems of review. At last, comparison of IEEE334 with RCC-E is conducted and explored. (authors)

Design Review Report for formal review of safety class features of exhauster system for rotary mode core sampling

International Nuclear Information System (INIS)

JANICEK, G.P.

2000-01-01

Report documenting Formal Design Review conducted on portable exhausters used to support rotary mode core sampling of Hanford underground radioactive waste tanks with focus on Safety Class design features and control requirements for flammable gas environment operation and air discharge permitting compliance

Design Review Report for formal review of safety class features of exhauster system for rotary mode core sampling

Energy Technology Data Exchange (ETDEWEB)

JANICEK, G.P.

2000-06-08

Report documenting Formal Design Review conducted on portable exhausters used to support rotary mode core sampling of Hanford underground radioactive waste tanks with focus on Safety Class design features and control requirements for flammable gas environment operation and air discharge permitting compliance.

Issue on NPP-I and C important to safety-Data Communication

International Nuclear Information System (INIS)

Koo, I. S.; Hong, S. B.; Cho, J. W.; Choi, Y. S.; Lee, J. C.

2010-01-01

1. Issue on CDV and FDIS of IEC61500 - Nuclear Power Plants - Instrumentation and control important to safety -Data communication - Activities on IEC TC45, SC45A/WGA3. 2. As issue the requirements for safety data communication which is essential part of digital I and C systems, the fundamental technology for IT based nuclear I and C is established. 3. Approval and circulation of IED61500 CDV and FDIS - Issue of the international standard, IEC 61500. 4. Issue one IEC61500, three interim documents, three presentations and five technical support to industry, and participation in IEC TC45 and SC45A plenary meeting and intermediate meeting on SC45A/WGA3. 5. Based on IEC61500, an new project on wireless technologyes application to NPP will be proceeded

The Evaluation of the Safety Benefits of Combined Passive and On-Board Active Safety Applications

Science.gov (United States)

Page, Yves; Cuny, Sophie; Zangmeister, Tobias; Kreiss, Jens-Peter; Hermitte, Thierry

2009-01-01

One of the objectives of the European TRACE project (TRaffic Accident Causation in Europe, 2006–2008) was to estimate the proportion of injury accidents that could be avoided and/or the proportion of injury accidents where the severity could be mitigated for on-the-market safety applications, if 100 % of the car fleet would be equipped with them. We have selected for evaluation the Electronic Stability Control (ESC) and the Emergency Brake Assist (EBA) applications. As for passive safety systems, recent cars are designed to offer overall safety protection. Car structure, load limiters, front airbags, side airbags, knee airbags, pretensioners, padding and non aggressive structures in the door panel, the dashboard, the windshield, the seats, and the head rest also contribute to applying more protection. The whole safety package is very difficult to evaluate separately, one element independently segmented from the others. We decided to consider evaluating the effectivenessof the whole passive safety package, This package,, for the sake of simplicity, was the number of stars awarded at the Euro NCAP testing. The challenges were to compare the effectiveness of some safety configuration SC I, with the effectiveness of a different safety configuration SC II. A safety configuration is understood as a package of safety functions. Ten comparisons have been carried out such as the evaluation of the safety benefit of a fifth star given that the car has four stars and an EBA. The main outcome of this analysis is that any addition of a passive or active safety function selected in this analysis is producing increased safety benefits. For example, if all cars were five stars fitted with EBA and ESC, instead of four stars without ESC and EBA, injury accidents would be reduced by 47.2% for severe injuries and 69.5% for fatal injuries. PMID:20184838

Design and Structural Analysis for the Vacuum Vessel of Superconducting Tokamak JT-60SC

International Nuclear Information System (INIS)

Kudo, Y.; Sakurai, S.; Masaki, K.; Urata, K.; Sasajima, T.; Matsukawa, M.; Sakasai, A.; Ishida, S.

2003-01-01

A modification of the JT-60 is planned to be a superconducting tokamak (JT-60SC) in order to establish steady-state operation of high beta plasma for 100 s, and to ensure the applicability of ferritic steel as a reduced activation material for reactor relevant break-even class plasmas. This paper describes the detailed design of the vacuum vessel, which has a unique structure for cost effective manufacturing, as well as structural analysis results for a feasibility study

Energy Levels and Radiative Rates for Transitions in F-like Sc XIII and Ne-like Sc XII and Y XXX

Science.gov (United States)

Aggarwal, Kanti

2018-05-01

Energy levels, radiative rates and lifetimes are reported for F-like Sc~XIII and Ne-like Sc~XII and Y~XXX for which the general-purpose relativistic atomic structure package ({\\sc grasp}) has been adopted. For all three ions limited data exist in the literature but comparisons have been made wherever possible to assess the accuracy of the calculations. In the present work the lowest 102, 125 and 139 levels have been considered for the respective ions. Additionally, calculations have also been performed with the flexible atomic code ({\\sc fac}) to (particularly) confirm the accuracy of energy levels.

Cyclotron production of {sup 44}Sc for clinical application

Energy Technology Data Exchange (ETDEWEB)

Krajewski, S.; Bilewicz, A. [Institute of Nuclear Chemistry and Technology, Warsaw (Poland); Cydzik, I. [Institute of Nuclear Chemistry and Technology, Warsaw (Poland); European Commission Joint Research Center, Ispra (Italy). Inst. for Health and Consumer Protection; Warsaw Univ. (Poland). Heavy Ion Lab.; Abbas, K. [European Commission Joint Research Center, Ispra (Italy). Institute for Transuranium Elements; Bulgheroni, A.; Simonelli, F.; Holzwarth, U. [European Commission Joint Research Center, Ispra (Italy). Inst. for Health and Consumer Protection

2013-08-01

{sup 44} is a promising {beta}{sup +}-emitter for molecular imaging with intermediate half-life of 4 h. Due to the chemical similarity of Sc{sup 3+} to the Lu{sup 3+} and Y{sup 3+} cations, {sup 44}Sc-DOTA bioconjugates are expected to demonstrate similar properties in vivo as the {sup 177}Lu- and {sup 90}Y-bioconjugates, what is important in planning the radionuclide therapy. {sup 44}Sc can be obtained from the {sup 44}Ti/{sup 44}Sc generator. An alternative method for {sup 44}Sc production can be the irradiation of {sup 44}Ca target at small cyclotrons. The aim of our work was to optimize the parameters of {sup 44}CaCO{sub 3} irradiation and to develop a simple procedure for {sup 44}Sc separation from the calcium target. For optimization study, {sup 44}CaCO{sub 3} targets were irradiated by protons in the energy range of 5.6-17.5 MeV with 9 MeV being found to be the best energy for {sup 44}Ca irradiations. A simple and fast separation procedure of {sup 44}Sc from calcium target was developed using chelating resin Chelex 100. DOTATATE conjugate was successfully radiolabelled with high yield at elevated temperature using the produced {sup 44}Sc. While {sup 44}CaCO{sub 3} is relatively expensive, the cost of {sup 44}Sc-DOTATATE production can be reduced by target recovery. Due to low proton energy required to produce GBq activity level of {sup 44}Sc, the availability of {sup 44}Sc radioisotope could be enhanced to open new opportunities for applications in medical imaging. (orig.)

Radiation Protection Section (SC/SL/RP)

CERN Document Server

2006-01-01

We should like to inform you that the Radiation Protection Section (SC/SL/RP) located on the Prévessin site has moved from Building 865 (ground floor) to new premises in Wing A of Building 892 (second floor). Telephone numbers remain the same. SC/SL/RP section

Comprehensive Lifecycle for Assuring System Safety

Science.gov (United States)

Knight, John C.; Rowanhill, Jonathan C.

2017-01-01

CLASS is a novel approach to the enhancement of system safety in which the system safety case becomes the focus of safety engineering throughout the system lifecycle. CLASS also expands the role of the safety case across all phases of the system's lifetime, from concept formation to decommissioning. As CLASS has been developed, the concept has been generalized to a more comprehensive notion of assurance becoming the driving goal, where safety is an important special case. This report summarizes major aspects of CLASS and contains a bibliography of papers that provide additional details.

Engineering approach to relative quantitative assessment of safety culture and related social issues in NPP operation

International Nuclear Information System (INIS)

Sivokon, V.; Gladyshev, M.; Malkin, S.

2005-01-01

The report is devoted to presentation of engineering approach and software tool developed for Safety Culture (SC) assessment as well as to the results of their implementation at Smolensk NPP. The engineering approach is logic evolution of the IAEA ASSET method broadly used at European NPPs in 90-s. It was implemented at Russian and other plants including Olkiluoto NPP in Finland. The approach allows relative quantitative assessing and trending the aspects of SC by the analysis of evens features and causes, calculation and trending corresponding indicators. At the same time plant's operational performances and related social issues, including efficiency of plant operation and personnel reliability, can be monitored. With the help of developed tool the joint team combined from personnel of Smolensk NPP and RRC 'Kurchatov Institute' ('KI') issued the SC self-assessment report, which identifies: families of recurrent events, main safety and operational problems ; their trends and importance to SC and plant efficiency; recommendations to enhance SC and operational performance

Longterm Safety and Efficacy of Subcutaneous Tocilizumab Monotherapy: Results from the 2-year Open-label Extension of the MUSASHI Study.

Science.gov (United States)

Ogata, Atsushi; Amano, Koichi; Dobashi, Hiroaki; Inoo, Masayuki; Ishii, Tomonori; Kasama, Tsuyoshi; Kawai, Shinichi; Kawakami, Atsushi; Koike, Tatsuya; Miyahara, Hisaaki; Miyamoto, Toshiaki; Munakata, Yasuhiko; Murasawa, Akira; Nishimoto, Norihiro; Ogawa, Noriyoshi; Ojima, Tomohiro; Sano, Hajime; Shi, Kenrin; Shono, Eisuke; Suematsu, Eiichi; Takahashi, Hiroki; Tanaka, Yoshiya; Tsukamoto, Hiroshi; Nomura, Akira

2015-05-01

To evaluate the longterm safety and efficacy of subcutaneous tocilizumab (TCZ-SC) as monotherapy in patients with rheumatoid arthritis (RA). Of 346 patients who received 24 weeks of double-blind treatment with either TCZ-SC monotherapy, 162 mg every 2 weeks (q2w); or intravenous TCZ (TCZ-IV) monotherapy, 8 mg/kg every 4 weeks; 319 patients continued to receive TCZ-SC q2w in the 84-week open-label extension (OLE) of the MUSASHI study (JAPICCTI-101117). Efficacy, safety, and immunogenicity were evaluated for all patients treated with TCZ during 108 weeks. The proportions of patients who achieved American College of Rheumatology 20/50/70 responses, low disease activity [28-joint Disease Activity Score (DAS28) ≤ 3.2], or remission (DAS28 < 2.6) at Week 24 were maintained until Week 108. The incidences of adverse events and serious adverse events were 498.3 and 16.9 per 100 patient-years (PY), respectively. The overall safety of TCZ-SC monotherapy was similar to that of TCZ-IV monotherapy. Rates of injection site reactions (ISR) through 108 weeks remained similar to rates through 24 weeks. ISR were mild and did not cause any patient withdrawals. No serious hypersensitivity events (including anaphylactic reactions) occurred. Anti-TCZ antibodies were present in 2.1% of patients treated with TCZ-SC monotherapy. TCZ-SC monotherapy maintained a favorable safety profile and consistent efficacy throughout the 108-week study. Like TCZ-IV, TCZ-SC could provide an additional treatment option for patients with RA.

Cyclotron production of {sup 43}Sc for PET imaging

Energy Technology Data Exchange (ETDEWEB)

Walczak, Rafał [Institute of Nuclear Chemistry and Technology, Dorodna 16, 03-195 Warsaw (Poland); Krajewski, Seweryn [Synektik S.A., Research and Development Center, Warsaw (Poland); Szkliniarz, Katarzyna [Department of Nuclear Physics, University of Silesia, Katowice (Poland); Sitarz, Mateusz [Heavy Ion Laboratory, University of Warsaw, Warsaw (Poland); Abbas, Kamel [Nuclear Security Unit, Joint Research Centre, Institute for Transuranium Elements, European Commission, Ispra (Italy); Choiński, Jarosław; Jakubowski, Andrzej; Jastrzębski, Jerzy [Heavy Ion Laboratory, University of Warsaw, Warsaw (Poland); Majkowska, Agnieszka [Institute of Nuclear Chemistry and Technology, Dorodna 16, 03-195 Warsaw (Poland); Simonelli, Federica [Nuclear Decommissioning Unit, Joint Research Centre, Ispra Site Management Directorate, European Commission, Ispra (Italy); Stolarz, Anna; Trzcińska, Agnieszka [Heavy Ion Laboratory, University of Warsaw, Warsaw (Poland); Zipper, Wiktor [Department of Nuclear Physics, University of Silesia, Katowice (Poland); Bilewicz, Aleksander [Institute of Nuclear Chemistry and Technology, Dorodna 16, 03-195 Warsaw (Poland)

2015-12-04

Recently, significant interest in {sup 44}Sc as a tracer for positron emission tomography (PET) imaging has been observed. Unfortunately, the co-emission by {sup 44}Sc of high-energy γ rays (E{sub γ} = 1157, 1499 keV) causes a dangerous increase of the radiation dose to the patients and clinical staff. However, it is possible to produce another radionuclide of scandium—{sup 43}Sc—having properties similar to {sup 44}Sc but is characterized by much lower energy of the concurrent gamma emissions. This work presents the production route of {sup 43}Sc by α irradiation of natural calcium, its separation and purification processes, and the labeling of [DOTA,Tyr3] octreotate (DOTATATE) bioconjugate. Natural CaCO{sub 3} and enriched [{sup 40}Ca]CaCO{sub 3} were irradiated with alpha particles for 1 h in an energy range of 14.8–30 MeV at a beam current of 0.5 or 0.25 μA. In order to find the optimum method for the separation of {sup 43}Sc from irradiated calcium targets, three processes previously developed for {sup 44}Sc were tested. Radiolabeling experiments were performed with DOTATATE radiobioconjugate, and the stability of the obtained {sup 43}Sc-DOTATATE was tested in human serum. Studies of {sup nat}CaCO{sub 3} target irradiation by alpha particles show that the optimum alpha particle energies are in the range of 24–27 MeV, giving 102 MBq/μA/h of {sup 43}Sc radioactivity which creates the opportunity to produce several GBq of {sup 43}Sc. The separation experiments performed indicate that, as with {sup 44}Sc, due to the simplicity of the operations and because of the chemical purity of the {sup 43}Sc obtained, the best separation process is when UTEVA resin is used. The DOTATATE conjugate was labeled by the obtained {sup 43}Sc with a yield >98 % at elevated temperature. Tens of GBq activities of {sup 43}Sc of high radionuclidic purity can be obtainable for clinical applications by irradiation of natural calcium with an alpha beam.

Assessment of Safety Culture within the Pakistan Nuclear Regulatory Authority (PNRA)

Energy Technology Data Exchange (ETDEWEB)

Afzal, Muhammad [Pakistan Nuclear Regulatory Authority, Islamabad (Pakistan); Choi, Kwang Sik [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2015-10-15

The objective of this study is to assess the SC of the Pakistan Nuclear Regulatory Authority (PNRA) by developing a performance indicator-based questionnaire. Aspects that potentially play important roles in developing perceptions of SC, including age, type of job, gender and duty hours of regulatory staff, are given due importance in this study. The study also identifies the strengths and weaknesses in the SC of the PNRA and can be used as a model study to assess the SC of other RBs. The questionnaire, developed to assess the SC of the PNRA, was in line with the PNRA's own defined attributes for SC. In the past, significant efforts have been made to ensure the safe operation of NPPs by improving designs and operating procedures; however, the nuclear accident at the Fukushima NPP in Japan in March 2011 revealed that the currently allotted hardware safety margins are not sufficient, and much work is needed to improve safety management in terms of SC. Initially, the concept of SC was introduced for operating organizations to ensure safe operation of NPPs; nonetheless, more recent investigations of nuclear events and accidents, especially Fukushima, and at Davis-Besse, in the US, have revealed that a strong focus is required to address and improve the SC of Regulatory Bodies (RBs). Strong SC is considered a vital tool for RBs to achieve their objectives and discharge their responsibilities in an effective and efficient manner. Though the relationship between the SC of RBs and that of operating organizations is not straight forward, it is believed that the former has a strong influence over the latter. The questionnaire was consistent in terms of the credible nature of its questions, and the response group covered different levels of PNRA staff, from managers to lower level staff. The results show that the PNRA staff have a very good understanding of the nature and significance of attributes of SC and are doing their best to exercise the same within the

Assessment of Safety Culture within the Pakistan Nuclear Regulatory Authority (PNRA)

International Nuclear Information System (INIS)

Afzal, Muhammad; Choi, Kwang Sik

2015-01-01

The objective of this study is to assess the SC of the Pakistan Nuclear Regulatory Authority (PNRA) by developing a performance indicator-based questionnaire. Aspects that potentially play important roles in developing perceptions of SC, including age, type of job, gender and duty hours of regulatory staff, are given due importance in this study. The study also identifies the strengths and weaknesses in the SC of the PNRA and can be used as a model study to assess the SC of other RBs. The questionnaire, developed to assess the SC of the PNRA, was in line with the PNRA's own defined attributes for SC. In the past, significant efforts have been made to ensure the safe operation of NPPs by improving designs and operating procedures; however, the nuclear accident at the Fukushima NPP in Japan in March 2011 revealed that the currently allotted hardware safety margins are not sufficient, and much work is needed to improve safety management in terms of SC. Initially, the concept of SC was introduced for operating organizations to ensure safe operation of NPPs; nonetheless, more recent investigations of nuclear events and accidents, especially Fukushima, and at Davis-Besse, in the US, have revealed that a strong focus is required to address and improve the SC of Regulatory Bodies (RBs). Strong SC is considered a vital tool for RBs to achieve their objectives and discharge their responsibilities in an effective and efficient manner. Though the relationship between the SC of RBs and that of operating organizations is not straight forward, it is believed that the former has a strong influence over the latter. The questionnaire was consistent in terms of the credible nature of its questions, and the response group covered different levels of PNRA staff, from managers to lower level staff. The results show that the PNRA staff have a very good understanding of the nature and significance of attributes of SC and are doing their best to exercise the same within the

Effective single chain antibody (scFv) concentrations in vivo via adenoviral vector mediated expression of secretory scFv

NARCIS (Netherlands)

Arafat, WO; Gomez-Navarro, J; Buchsbaum, DJ; Xiang, J; Casado, E; Barker, SD; Mahasreshti, PJ; Haisma, HJ; Barnes, MN; Siegal, GP; Alvarez, RD; Hemminki, A; Nettelbeck, DM; Curiel, DT

Single chain antibodies (scFv) represent powerful interventional agents for the achievement of targeted therapeutics. The practical utility of these agents have been limited, however, by difficulties related to production of recombinant scFv and the achievement of effective and sustained levels of

Hemoglobin C, S-C, and E Diseases

Science.gov (United States)

... quickly than others, resulting in chronic anemia. Hemoglobin C disease Hemoglobin C disease occurs mostly in blacks. ... a common complication of hemoglobin C disease. Hemoglobin S-C disease Hemoglobin S-C disease occurs in people who ...

INCREASING OF THE EXPRESSION OF RECOMBINANT scFv-ANTIBODIES EFFICIENCY

Directory of Open Access Journals (Sweden)

O.V. Galkin

2017-10-01

Full Text Available Obtaining single-chain variable fragments (scFv of recombinant antibodies in E. coli cells is often associated with numerous problems causing low yields or inactive conformation of the product. The aim of this work was to study the influence of staphylococcal protein A fragment fused with scFv antibodies (SpA-tag on the efficiency of expression of final product. Examination of scFv antibodies of different origin and specificity has shown that in similar expression systems fused scFv is synthesized in much higher quantities than free scFv. Furthermore, the scFv antibodies in fused form retained their antigen-binding properties and the SpA fragment the ability to bind other immunoglobulins. Thus, the proposed strategy can be considered effective in improving the efficiency of scFv-antibodies production in E. coli cells.

Knowledge and practices about hospital waste disposal and universal safety precautions in class IV employee.

Science.gov (United States)

Megha, Khobragade; Daksha, Pandit

2013-01-01

Norms and guidelines are formed for safe disposal of hospital waste but question is whether these guidelines are being followed and if so, to what extent. Hence, this study was conducted with objective to study the knowledge and practices about hospital waste disposal and universal safety precautions in class IV employee and to study its relationship with education, occupation and training. A cross-sectional study was carried out in a teaching hospital in Mumbai using semi-structured questionnaire in which Class IV employee were included. Questionnaire was filled by face to face interview. Data were analyzed using SPSS. 48.7% Class IV employee were not trained. More than 40% were following correct practices about disinfection of infectious waste. None of the respondents were using protective footwear while handling hospital waste. Only 25.5% were vaccinated for hepatitis B. 16% had done HIV testing due to contact with blood, body fluid, needle stick injury. Knowledge and practices about hospital waste disposal and universal precaution were statistically significant in trained respondents. Training of employees should be given top priority; those already in service should be given on the job training at the earliest.

PET imaging of 64Cu-DOTA-scFv-anti-PSMA lipid nanoparticles (LNPs): Enhanced tumor targeting over anti-PSMA scFv or untargeted LNPs

International Nuclear Information System (INIS)

Wong, Patty; Li, Lin; Chea, Junie; Delgado, Melissa K.; Crow, Desiree; Poku, Erasmus; Szpikowska, Barbara; Bowles, Nicole; Channappa, Divya; Colcher, David; Wong, Jeffrey Y.C.; Shively, John E.; Yazaki, Paul J.

2017-01-01

Introduction: Single chain (scFv) antibodies are ideal targeting ligands due to their modular structure, high antigen specificity and affinity. These monovalent ligands display rapid tumor targeting but have limitations due to their fast urinary clearance. Methods: An anti-prostate membrane antigen (PSMA) scFv with a site-specific cysteine was expressed and evaluated in a prostate cancer xenograft model by Cu-64 PET imaging. To enhance tumor accumulation, the scFv-cys was conjugated to the co-polymer DSPE-PEG-maleimide that spontaneously assembled into a homogeneous multivalent lipid nanoparticle (LNP). Results: The targeted LNP exhibited a 2-fold increase in tumor uptake compared to the scFv alone using two different thiol ester chemistries. The anti-PSMA scFv-LNP exhibited a 1.6 fold increase in tumor targeting over the untargeted LNP. Conclusions: The targeted anti-PSMA scFv-LNP showed enhanced tumor accumulation over the scFv alone or the untargeted DOTA-micelle providing evidence for the development of this system for drug delivery. Advances in knowledge and implications for patient care: Anti-tumor scFv antibody fragments have not achieved their therapeutic potential due to their fast blood clearance. Conjugation to an LNP enables multivalency to the tumor antigen as well as increased molecular size for chemotherapy drug delivery.

A Further Study of the Products of Sc and Dioxygen Reactions

Science.gov (United States)

Bauschlicher, Charles W., Jr.; Zhou, Mingfei; Andrews, Lester; Johnson, J. R. Tobias; Panas, Itai; Snis, Anders; Roos, Bjoern O.; Arnold, James O. (Technical Monitor)

1999-01-01

The products of the reaction of Sc and dioxygen have been reinvestigated. By adding the electron-trapping molecule CC14, additional information about the IR spectra has been obtained, as well as the observation of new bands. New ab initio calculations are also performed on possible products of the Sc plus O2 reaction. The previously observed band at 722.5 per cm is assigned as the b2 mode of ScO2(-). Bands arising from ScO(+), Sc(O2)(+), and(O2)ScO are also assigned. We are still unable to assign any bands to OScO. The problems associated with the computational study of ScO2 are discussed.

Synthesis and Isolation of the Titanium-Scandium Endohedral Fullerenes-Sc2 TiC@Ih -C80 , Sc2 TiC@D5h -C80 and Sc2 TiC2 @Ih -C80 : Metal Size Tuning of the Ti(IV) /Ti(III) Redox Potentials.

Science.gov (United States)

Junghans, Katrin; Ghiassi, Kamran B; Samoylova, Nataliya A; Deng, Qingming; Rosenkranz, Marco; Olmstead, Marilyn M; Balch, Alan L; Popov, Alexey A

2016-09-05

The formation of endohedral metallofullerenes (EMFs) in an electric arc is reported for the mixed-metal Sc-Ti system utilizing methane as a reactive gas. Comparison of these results with those from the Sc/CH4 and Ti/CH4 systems as well as syntheses without methane revealed a strong mutual influence of all key components on the product distribution. Whereas a methane atmosphere alone suppresses the formation of empty cage fullerenes, the Ti/CH4 system forms mainly empty cage fullerenes. In contrast, the main fullerene products in the Sc/CH4 system are Sc4 C2 @C80 (the most abundant EMF from this synthesis), Sc3 C2 @C80 , isomers of Sc2 C2 @C82 , and the family Sc2 C2 n (2 n=74, 76, 82, 86, 90, etc.), as well as Sc3 CH@C80 . The Sc-Ti/CH4 system produces the mixed-metal Sc2 TiC@C2 n (2 n=68, 78, 80) and Sc2 TiC2 @C2 n (2 n=80) clusterfullerene families. The molecular structures of the new, transition-metal-containing endohedral fullerenes, Sc2 TiC@Ih -C80 , Sc2 TiC@D5h -C80 , and Sc2 TiC2 @Ih -C80 , were characterized by NMR spectroscopy. The structure of Sc2 TiC@Ih -C80 was also determined by single-crystal X-ray diffraction, which demonstrated the presence of a short Ti=C double bond. Both Sc2 TiC- and Sc2 TiC2 -containing clusterfullerenes have Ti-localized LUMOs. Encapsulation of the redox-active Ti ion inside the fullerene cage enables analysis of the cluster-cage strain in the endohedral fullerenes through electrochemical measurements. © 2016 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Loosely coupled class families

DEFF Research Database (Denmark)

Ernst, Erik

2001-01-01

are expressed using virtual classes seem to be very tightly coupled internally. While clients have achieved the freedom to dynamically use one or the other family, it seems that any given family contains a xed set of classes and we will need to create an entire family of its own just in order to replace one...... of the members with another class. This paper shows how to express class families in such a manner that the classes in these families can be used in many dierent combinations, still enabling family polymorphism and ensuring type safety....

Characteristics of the safety climate in teams with world-class safety ...

African Journals Online (AJOL)

interact to deliver a project successfully in terms of cost .... small-scale accidents occurring at high frequency and from diverse ... the team dynamics of role players in a construction project and .... modified safety pyramid to measure the impact of the safety climate ...... Methodological Centre for Vocational Education and.

Energy Levels, wavelengths and hyperfine structure measurements of Sc II

Science.gov (United States)

Hala, Fnu; Nave, Gillian

2018-01-01

Lines of singly ionized Scandium (Sc II) along with other Iron group elements have been observed [1] in the region surrounding the massive star Eta Carinae [2,3] called the strontium filament (SrF). The last extensive analysis of Sc II was the four-decade old work of Johansson & Litzen [4], using low-resolution grating spectroscopy. To update and extend the Sc II spectra, we have made observation of Sc/Ar, Sc/Ne and Sc/Ge/Ar hollow cathode emission spectrum on the NIST high resolution FT700 UV/Vis and 2 m UV/Vis/IR Fourier transform spectrometers (FTS). More than 850 Sc II lines have been measured in the wavelength range of 187 nm to 3.2 μm. connecting a total of 152 energy levels. The present work also focuses to resolve hyperfine structure (HFS) in Sc II lines. We aim to obtain accurate transition wavelengths, improved energy levels and HFS constants of Sc II. The latest results from work in progress will be presented.Reference[1] Hartman H, Gull T, Johansson S and Smith N 2004 Astron. Astrophys. 419 215[2] Smith N, Morse J A and Gull T R 2004 Astrophys. J. 605 405[3] Davidson K and Humphreys R M 1997 Annu. Rev. Astron. Astrophys. 35[4] Johansson S and Litzén U 1980 Phys. Scr. 22 49

Sc-Decorated WS_2 Nanoribbons as Hydrogen Storage Media

International Nuclear Information System (INIS)

Xu Bin; Wang Yu-Sheng; Zhang Jing; Song Na-Hong; Li Meng; Yi Lin

2016-01-01

The hydrogen storage behavior of Sc-decorated WS_2 monolayer and WS_2 nanoribbons is systematically studied by using first principles calculations based on the density functional theory. The present results indicate that an Sc-decorated WS_2 monolayer is not suitable for storing hydrogen due to the weak interaction between the monolayer WS_2 sheet and the Sc atoms. It is found that both the hybridization mechanism and the Coulomb attraction make the Sc atoms stably adsorb on the edges of WS_2 nanoribbons without clustering. The 2Sc/WS_2 NRs system can adsorb at most eight H_2 molecules with average adsorption energy of 0.20 eV/H_2. The results show that the desorption of H_2 is possible by lowering the pressure or by increasing the temperature. (paper)

CORRELATION BETWEEN SEED TESTS AND FIELD EMERGENCE OF TWO MAIZE HYBRIDS (SC704 AND SC500)

OpenAIRE

A.A. ALILOO; B. SHOKATI

2011-01-01

Early emergence and stand establishment of maize (Zea mays L.) are considered to be the most important yield-contributing factors. The influence of seed vigor on these factors is vital. Therefore, five laboratory tests and field experiment were conducted on basis of a randomized complete block design (RCBD) with five replications in 2011, to evaluate the correlation among the seed vigor tests and field emergence of two maize hybrids (SC704 and SC500). In laboratory tests, differences between ...

Depletion of Arabidopsis SC35 and SC35-like serine/arginine-rich proteins affects the transcription and splicing of a subset of genes.

Science.gov (United States)

Yan, Qingqing; Xia, Xi; Sun, Zhenfei; Fang, Yuda

2017-03-01

Serine/arginine-rich (SR) proteins are important splicing factors which play significant roles in spliceosome assembly and splicing regulation. However, little is known regarding their biological functions in plants. Here, we analyzed the phenotypes of mutants upon depleting different subfamilies of Arabidopsis SR proteins. We found that loss of the functions of SC35 and SC35-like (SCL) proteins cause pleiotropic changes in plant morphology and development, including serrated leaves, late flowering, shorter roots and abnormal silique phyllotaxy. Using RNA-seq, we found that SC35 and SCL proteins play roles in the pre-mRNA splicing. Motif analysis revealed that SC35 and SCL proteins preferentially bind to a specific RNA sequence containing the AGAAGA motif. In addition, the transcriptions of a subset of genes are affected by the deletion of SC35 and SCL proteins which interact with NRPB4, a specific subunit of RNA polymerase II. The splicing of FLOWERING LOCUS C (FLC) intron1 and transcription of FLC were significantly regulated by SC35 and SCL proteins to control Arabidopsis flowering. Therefore, our findings provide mechanistic insight into the functions of plant SC35 and SCL proteins in the regulation of splicing and transcription in a direct or indirect manner to maintain the proper expression of genes and development.

Building a World-Class Safety Culture: The National Ignition Facility and the Control of Human and Organizational Error

International Nuclear Information System (INIS)

Bennett, C T; Stalnaker, G

2002-01-01

Accidents in complex systems send us signals. They may be harbingers of a catastrophe. Some even argue that a ''normal'' consequence of operations in a complex organization may not only be the goods it produces, but also accidents and--inevitably--catastrophes. We would like to tell you the story of a large, complex organization, whose history questions the argument ''that accidents just happen.'' Starting from a less than enviable safety record, the National Ignition Facility (NIF) has accumulated over 2.5 million safe hours. The story of NIF is still unfolding. The facility is still being constructed and commissioned. But the steps NIF has taken in achieving its safety record provide a principled blueprint that may be of value to others. Describing that principled blueprint is the purpose of this paper. The first part of this paper is a case study of NIF and its effort to achieve a world-class safety record. This case study will include a description of (1) NIF's complex systems, (2) NIF's early safety history, (3) factors that may have initiated its safety culture change, and (4) the evolution of its safety blueprint. In the last part of the paper, we will compare NIF's safety culture to what safety industry experts, psychologists, and sociologists say about how to shape a culture and control organizational error

Safety, Tolerability, and Antihypertensive Effect of SER100, an Opiate Receptor-Like 1 (ORL-1) Partial Agonist, in Patients With Isolated Systolic Hypertension.

Science.gov (United States)

Kantola, Ilkka; Scheinin, Mika; Gulbrandsen, Trygve; Meland, Nils; Smerud, Knut T

2017-11-01

The purpose of the present trial was to evaluate safety, tolerability, and effect on systolic blood pressure (SBP) of SER100 in a small group of patients with isolated systolic hypertension (ISH) in treatment with at least 1 antihypertensive drug. Eligible patients were randomized to either SER100 (10 mg) or placebo in a crossover design, and 2 doses were given subcutaneously (SC), 8 hours apart, on 2 consecutive days. On all treatment days patients were monitored with an ambulatory blood pressure measurement device for 12 daytime hours. Seventeen patients completed treatment. There were no serious or severe adverse events. Relative to placebo SER100 induced an average reduction of SBP during the 2 treatment days of 7.0 mm Hg (P = 0.0032), whereas the average reduction of diastolic blood pressure (DBP) over the same period was 3.8 mm Hg (P = 0.0011). For patients with ISH, this short-term cross-over study of SC SER100 demonstrated an acceptable safety profile and consistent, significant lowering of SBP and DBP. As initial clinical proof of concept for a new class of drugs, a nociceptin agonist peptide, the results were encouraging and warrant further research. © 2016, The American College of Clinical Pharmacology.

Evaluation of temporary non-code repairs in safety class 3 piping systems

International Nuclear Information System (INIS)

Godha, P.C.; Kupinski, M.; Azevedo, N.F.

1996-01-01

Temporary non-ASME Code repairs in safety class 3 pipe and piping components are permissible during plant operation in accordance with Nuclear Regulatory Commission Generic Letter 90-05. However, regulatory acceptance of such repairs requires the licensee to undertake several timely actions. Consistent with the requirements of GL 90-05, this paper presents an overview of the detailed evaluation and relief request process. The technical criteria encompasses both ductile and brittle piping materials. It also lists appropriate evaluation methods that a utility engineer can select to perform a structural integrity assessment for design basis loading conditions to support the use of temporary non-Code repair for degraded piping components. Most use of temporary non-code repairs at a nuclear generating station is in the service water system which is an essential safety related system providing the ultimate heat sink for various plant systems. Depending on the plant siting, the service water system may use fresh water or salt water as the cooling medium. Various degradation mechanisms including general corrosion, erosion/corrosion, pitting, microbiological corrosion, galvanic corrosion, under-deposit corrosion or a combination thereof continually challenge the pressure boundary structural integrity. A good source for description of corrosion degradation in cooling water systems is provided in a cited reference

DiSC-OPAL

DEFF Research Database (Denmark)

Kemal, Mohammed Seifu; Pedersen, Rasmus; Iov, Florin

2017-01-01

of such systems. The simulation tool should be able to model Electrical Grid and flexible assets with different time scales and resolution levels fulfilling specific functionalities. In this paper DiSC-OPAL, an OPAL-RT compatible toolbox library for modelling of assets is presented. The library is suitable...

New indides Sc{sub 6}Co{sub 2.18}In{sub 0.82}, Sc{sub 10}Ni{sub 9}In{sub 19.44} and ScCu{sub 4}In-synthesis, structure, and crystal chemistry

Energy Technology Data Exchange (ETDEWEB)

Zaremba, R.I.; Rodewald, U. Ch.; Poettgen, R. [Inst. fuer Anorganische und Analytische Chemie, Westfaelische Wilhelms-Univ. Muenster (Germany); Kalychak, Y.M.; Zaremba, V.I. [Inorganic Chemistry Dept., Ivan Franko National Univ. of Lviv, Lviv (Ukraine)

2006-08-15

New indides Sc{sub 6}Co{sub 2.18}In{sub 0.82}, Sc{sub 10}Ni{sub 9}In{sub 19.44} and ScCu{sub 4}In have been synthesized from the elements by arc-melting. Single crystals were grown by special annealing modes. The thee indides were investigated via X-ray powder and single crystal diffraction: Ho{sub 6}Co{sub 2}Ga type, Immm, a = 886.7(3), b = 878.0(2), c = 932.1(3) pm, wR2 = 0.0517, 711 F{sup 2} values, 35 variables for Sc{sub 6}Co{sub 2.18}In{sub 0.82}, Ho{sub 10}Ni{sub 9}In{sub 20} type, P4/nmm, a = 1287.5(2), c = 884.7(1) pm, wR2 = 0.0642, 1221 F{sup 2} values, 63 variables for Sc{sub 10}Ni{sub 9}In{sub 19.44}, and MgCu{sub 4}Sn type, anti F 43m, a = 704.03(7) pm, wR2 = 0.0267, 101 F{sup 2} values, and 7 variables for ScCu{sub 4}In. The scandium rich indide Sc{sub 6}Co{sub 2.18}In{sub 0.82} contains two Co{sub 2} dumb-bells at Co-Co distances of 221 and 230 pm. Each cobalt atom within these dumb-bells has a tricapped trigonal prismatic coordination. The In1 site has a distorted cube-like coordination by scandium and shows a mixed occupancy (36%) with cobalt. The In2 atoms have distorted icosahedral scandium coordination. As a consequence of the small size of the scandium atoms, the In4 site in Sc{sub 10}Ni{sub 9}In{sub 19.44} shows defects and was furthermore refined with a split model leading to a new distorted variant within the family of Ho{sub 10}Ni{sub 9}In{sub 20} compounds. ScCu{sub 4}In is an ordered version of the cubic Laves phase with scandium and indium atoms in the CN16 voids of the copper substructure. The Cu-Cu distances within the three-dimensional network of corner-sharing tetrahedra are 248.6 and 249.2 pm. The crystal chemical peculiarities of these three indide structures are briefly discussed. (orig.)

PET Imaging of 64Cu-DOTA-scFv-Anti-PSMA Lipid Nanoparticles (LNPs): Enhanced Tumor Targeting over Anti-PSMA scFv or Untargeted LNPs

Science.gov (United States)

Wong, Patty; Li, Lin; Chea, Junie; Delgado, Melissa K.; Crow, Desiree; Poku, Erasmus; Szpikowska, Barbara; Bowles, Nicole; Channappa, Divya; Colcher, David; Wong, Jeffrey Y.C.; Shively, John E.; Yazaki, Paul J.

2017-01-01

Introduction Single chain (scFv) antibodies are ideal targeting ligands due to their modular structure, high antigen specificity and affinity. These monovalent ligands display rapid tumor targeting but have limitations due to their fast urinary clearance. Methods An anti-prostate membrane antigen (PSMA) scFv with a site-specific cysteine was expressed and evaluated in a prostate cancer xenograft model by Cu-64 PET imaging. To enhance tumor accumulation, the scFv-cys was conjugated to the co-polymer DSPE-PEG-maleimide that spontaneously assembled into a homogeneous multivalent lipid nanoparticle (LNP). Results The targeted LNP exhibited a 2-fold increase in tumor uptake compared to the scFv alone using two different thiol ester chemistries. The anti-PSMA scFv-LNP exhibited a 1.6 fold increase in tumor targeting over the untargeted LNP. Conclusions The targeted anti-PSMA scFv-LNP showed enhanced tumor accumulation over the scFv alone or the untargeted DOTA-micelle providing evidence for the development of this system for drug delivery. Advances in Knowledge and implications for patient care Anti-tumor scFv antibody fragments have not achieved their therapeutic potential due to their fast blood clearance. Conjugation to a LNP enables multivalency to the tumor antigen as well as increased molecular size for chemotherapy drug delivery. PMID:28126683

Molecular and functional characterization of peptidoglycan-recognition protein SC2 (PGRP-SC2) from Nile tilapia (Oreochromis niloticus) involved in the immune response to Streptococcus agalactiae.

Science.gov (United States)

Gan, Zhen; Chen, Shannan; Hou, Jing; Huo, Huijun; Zhang, Xiaolin; Ruan, Baiye; Laghari, Zubair Ahmed; Li, Li; Lu, Yishan; Nie, Pin

2016-07-01

PGRP-SC2, the member of PGRP family, plays an important role in regulation of innate immune response. In this paper, a PGRP-SC2 gene of Nile tilapia, Oreochromis niloticus (designated as On-PGRP-SC2) was cloned and its expression pattern under the infection of Streptococcus agalactiae was investigated. Sequence analysis showed main structural features required for amidase activity were detected in the deduced amino acid sequence of On-PGRP-SC2. In healthy tilapia, the On-PGRP-SC2 transcripts could be detected in all the examined tissues, with the most abundant expression in the muscle. When infected with S. agalactiae, there was a clear time-dependent expression pattern of On-PGRP-SC2 in the spleen, head kidney and brain. The assays for the amidase activity suggested that recombinant On-PGRP-SC2 protein had a Zn(2+)-dependent PGN-degrading activity. Moreover, our works showed that recombinant On-PGRP-SC2 protein could significantly reduce bacterial load in target organs attacked by S. agalactiae. These findings indicated that On-PGRP-SC2 may play important roles in the immune response to S. agalactiae in Nile tilapia. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pascal-SC a computer language for scientific computation

CERN Document Server

Bohlender, Gerd; von Gudenberg, Jürgen Wolff; Rheinboldt, Werner; Siewiorek, Daniel

1987-01-01

Perspectives in Computing, Vol. 17: Pascal-SC: A Computer Language for Scientific Computation focuses on the application of Pascal-SC, a programming language developed as an extension of standard Pascal, in scientific computation. The publication first elaborates on the introduction to Pascal-SC, a review of standard Pascal, and real floating-point arithmetic. Discussions focus on optimal scalar product, standard functions, real expressions, program structure, simple extensions, real floating-point arithmetic, vector and matrix arithmetic, and dynamic arrays. The text then examines functions a

Thermodynamic modeling of the Sc-Zn system coupled with first-principles calculation

Directory of Open Access Journals (Sweden)

Tang C.

2012-01-01

Full Text Available The Sc-Zn system has been critically reviewed and assessed by means of CALPHAD (CALculation of PHAse Diagram approach. By means of first-principles calculation, the enthalpies of formation at 0 K for the ScZn, ScZn2, Sc17Zn58, Sc3Zn17 and ScZn12 have been computed with the desire to assist thermodynamic modeling. A set of self-consistent thermodynamic parameters for the Sc-Zn system is then obtained. The calculated phase diagram and thermodynamic properties agree well with the experimental data and first-principles calculations, respectively.

Lifetime and g-factor measurements in 44Sc

International Nuclear Information System (INIS)

Chevallier, A.; Chavallier, J.; Gross, J.L.; Haas, B.; Schulz, N.; Styczen, J.; Toulemonde, M.

1975-01-01

The lifetimes of the 235 keV, 2 - state and 350 keV, 4 + state in 44 Sc have been measured via the 44 Ca(p, n) 44 Sc reaction with a pulsed proton beam. The time integral perturbed angular distribution technique with an external field was used to measure the precession angles of the 2 - and 4 + states populated by the 30 Si( 16 O, pnγ) 44 Sc reaction. The following values for the mean-lives and g-factors were obtained: π(2 - ) = 8.83(33) ns, g(2 - ) = 0.30(13) and π(4 + ) = 4.52(27)ns, g(4 + ) = 0.90(12). The results for the 2 - state support a rotational description of the negative parity states in 44 Sc. The magnetic moment of the 4 + state is compared to shell model predictions. (orig.) [de

Electronic structure and local distortions in epitaxial ScGaN films

International Nuclear Information System (INIS)

Knoll, S M; Zhang, S; Rovezzi, M; Joyce, T B; Moram, M A

2014-01-01

High energy resolution fluorescence-detected x-ray absorption spectroscopy and density functional theory calculations were used to investigate the local bonding and electronic structure of Sc in epitaxial wurtzite-structure Sc x Ga 1−x N films with x ≤ 0.059. Sc atoms are found to substitute for Ga atoms, accompanied by a local distortion involving an increase in the internal lattice parameter u around the Sc atoms. The local bonding and electronic structure at Sc are not affected strongly by the strain state or the defect microstructure of the films. These data are consistent with theoretical predictions regarding the electronic structure of dilute Sc x Ga 1−x N alloys. (paper)

Verification of BGA type FPGA logic applied to a control equipment with Safety Class using the special socket

International Nuclear Information System (INIS)

Chung, YounHu; Yoo, Kwanwoo; Lee, Myeongkyun; Yun, Donghwa

2015-01-01

This article aims to provide the verification method for BGA-type FPGA of Programmable Logic Controller (PLC) developed as Safety Class. The logic of FPGA in the control device with Safety Class is the circuit to control overall logic of PLC. This device converts to the different module from the input signals for both digital and analogue of the equipment in the field and outputs their data. In addition, it should perform the logical controls such as backplane communication control and data communication. We suggest acquiring method of the data signal with efficient logic using the socket in this article. Proposed test socket is made by simpler process than former one, and the process is done in batches by which cost can be reduces, and the test socket can be quickly produced in response to any request. Also, it is possible to reduce the wear by reducing the contact force of the ball phenomenon. The structure on the basis of silicon can be reduced the modification, and it has excellent linearity. At the logic verification, the operation that state data block is designed in the FPGA could be easily confirmed by using a socket

Safety Assessment in Installation of Precast Concrete

Directory of Open Access Journals (Sweden)

Yashrri S.N.

2014-03-01

Full Text Available This study was carried out to identify the safety aspects and the level of safety during the installation process in construction sites. A questionnaire survey and interviews were done to provide data on safety requirements in precast concrete construction. All of the interviews and the research questionnaire survey were conducted among contractors that are registered as class 1 to class 7 with the Construction Industry Development Board (CIDB and class A to class G with Pusat Khidmat Kontraktor (PKK in Penang. Returned questionnaires were analysed with the use of simple percentages and the Likert Scale analysis method to identify safety aspects of precast construction. The results indicate that the safety aspect implemented by companies involved in the precast construction process is at a good level in the safety aspect during bracing, propping, welding and grouting processes and at a very good level of safety in general aspects and safety aspects during lifting processes.

Design of SC walls and slabs for impulsive loading

Energy Technology Data Exchange (ETDEWEB)

Varma, Amit H. [Purdue Univ., West Lafayette, IN (United States)

2015-11-11

Reinforced concrete (RC) structures have historically been the preferred choice for blast resistant structures because of their mass and the ductility provided by steel reinforcement. Steel-plate composite (SC) walls are a viable alternative to RC for protecting the infrastructure against explosive threats. SC structures consist of two steel faceplates with a plain concrete core between them. The steel faceplates are anchored to the concrete using stud anchors and connected to each other using tie bars. SC structures provide mass from the concrete infill and ductility from the continuous external steel faceplates. This dissertation presents findings and recommendations from experimental and analytical investigations of the performance of SC walls subjected to far-field blast loads.

LOCAL COLLISION SIMULATION OF AN SC WALL USING ENERGY ABSORBING STEEL

Directory of Open Access Journals (Sweden)

CHUL-HUN CHUNG

2013-08-01

Full Text Available This study evaluates the local damage of a turbine in an auxiliary building of a nuclear power plant due to an external impact by using the LS-DYNA finite element program. The wall of the auxiliary building is SC structure and the material of the SC wall plate is high manganese steel, which has superior ductility and energy absorbance compared to the ordinary steel used for other SC wall plates. The effects of the material of the wall, collision speed, and angle on the magnitude of the local damage were evaluated by local collision analysis. The analysis revealed that the SC wall made of manganese steel had significantly less damage than the SC wall made of ordinary steel. In conclusion, an SC wall made of manganese steel can have higher effective resistance than an SC wall made of ordinary steel against the local collision of an airplane engine or against a turbine impact.

Local Collision Simulation of an SC Wall Using Energy Absorbing Steel

Energy Technology Data Exchange (ETDEWEB)

Chung, Chulhun; Choi, Hyun; Park, Jaegyun [Dankook Univ., Yongin (Korea, Republic of)

2013-08-15

This study evaluates the local damage of a turbine in an auxiliary building of a nuclear power plant due to an external impact by using the LS-DYNA finite element program. The wall of the auxiliary building is SC structure and the material of the SC wall plate is high manganese steel, which has superior ductility and energy absorbance compared to the ordinary steel used for other SC wall plates. The effects of the material of the wall, collision speed, and angle on the magnitude of the local damage were evaluated by local collision analysis. The analysis revealed that the SC wall made of manganese steel had significantly less damage than the SC wall made of ordinary steel. In conclusion, an SC wall made of manganese steel can have higher effective resistance than an SC wall made of ordinary steel against the local collision of an airplane engine or against a turbine impact.

Longterm Safety and Efficacy of Subcutaneous Abatacept in Patients with Rheumatoid Arthritis: 5-year Results from a Phase IIIb Trial.

Science.gov (United States)

Genovese, Mark C; Pacheco-Tena, César; Covarrubias, Arturo; Leon, Gustavo; Mysler, Eduardo; Keiserman, Mauro; Valente, Robert M; Nash, Peter; Simon-Campos, J Abraham; Box, Jane; Legerton, Clarence W; Nasonov, Evgeny; Durez, Patrick; Elegbe, Ayanbola; Wong, Robert; Li, Xiaohui; Banerjee, Subhashis; Alten, Rieke

2018-04-15

To assess 5-year safety, tolerability, and efficacy of subcutaneous (SC) abatacept (ABA) in methotrexate (MTX)-refractory patients with rheumatoid arthritis (RA). The Abatacept Comparison of sub[QU]cutaneous versus intravenous in Inadequate Responders to methotrexatE (ACQUIRE) phase IIIb, randomized, double-dummy, multinational trial compared efficacy and safety of SC and intravenous (IV) ABA in patients with RA. In the initial 6-month double-blind (DB) period, patients received IV or SC ABA, plus MTX, and in the subsequent open-label longterm extension (LTE) period, all patients received SC ABA (125 mg/wk). The final 5-year safety, tolerability, and efficacy analyses are reported. Of 1385 patients who completed the DB period, 1372 entered LTE and 945 (68.8%) completed ≥ 5 years of treatment. During LTE, 97 (7.1%) patients discontinued treatment because of an adverse event (AE). Incidence rate (IR; event/100 patient-yrs of exposure; based on LTE data, 95% CI) for AE of interest were the following: serious AE 7.73 (6.96-8.58), infection 38.60 (36.24-41.12), serious infection 1.68 (1.35-2.07), malignancies 1.09 (0.84-1.42), and autoimmune disorders 1.33 (1.05-1.69), and were stable over time. No association between immunogenicity and either worsening of ABA safety or loss of efficacy was noted. Efficacy in the LTE was consistent with the DB period and was maintained to the end of the study. These 5-year data establish that SC ABA (125 mg/wk) has a consistent safety profile and durable efficacy for longterm treatment of patients with RA who had an inadequate response to MTX.

Atomic bonding and mechanical properties of Al-Mg-Zr-Sc alloy

Institute of Scientific and Technical Information of China (English)

高英俊; 班冬梅; 韩永剑; 钟夏平; 刘慧

2004-01-01

The valence electron structures of Al-Mg alloy with minor Sc and Zr were calculated according to the empirical electron theory(EET) in solid. The results show that because of the strong interaction of Al atom with Zr and Sc atom in melting during solidification, the Al3 Sc and Al3 (Sc1-xZrx) particles which act as heterogeneous nuclear are firstly crystallized in alloy to make grains refine. In progress of solidification, the Al-Sc, Al-Zr-Sc segregation regions are formed in solid solution matrix of Al-Mg alloy owing to the strong interaction of Al atom with Zr, Scatoms in bulk of alloy, so in the following homogenization treatment, the finer dispersed Al3 Sc and Al3 (Sc1-x Zrx) second-particles which are coherence with the matrix are precipitated in the segregation region. These finer second particles with the strong Al-Zr, Al-Sc covalent bonds can strengthen the covalent bonds in matrix of the alloy, and also enhance the hardness and strength of Al-Mg alloy. Those finer second-particles precipitated in interface of sub-grains can also strengthen the covalence bonds there, and effectively hinder the interface of sub-grains from migrating and restrain the sub-grains from growing, and cause better thermal stability of Al-Mg alloy.

Microstructure evolution of the 1469 Al–Cu–Li–Sc alloy during homogenization

Energy Technology Data Exchange (ETDEWEB)

Jia, Min, E-mail: jm_lushan@163.com; Zheng, Ziqiao, E-mail: csu1469@163.com; Gong, Zhu, E-mail: start123gz@163.com

2014-11-25

Highlights: • The formation of the W phase (AlCuSc) was found in the 1469 Al-Cu–Li–Sc alloy. • The W phase formed during the homogenization process. • We model the formation process of the W phase. • The formation of the W phase consumes lots of Cu and Sc atoms. - Abstract: The present work aims to clarify the formation of the W phase (AlCuSc) and its formation time in the high Cu content alloy with Sc addition. The microstructure evolution during the two-step homogenization annealing process was investigated in the 1469 Al–Cu–Li–Sc alloy. No evidences of the Al{sub 3}Sc phase and the W phase were found in the solidification structure. The arrays of the W phases were found to form after homogenization. The AlCu phases with traces of Sc that formed during solidification suppose to be the precursor of the W phases, and then transform into the W phases by consuming the Sc atoms that fixed in the supersaturate solid solution. The formation of the W phase inhibits the precipitation of the Al{sub 3}Sc phase. A corresponding model of the W phase formation mechanism is proposed.

Review of the conclusions of the 1996 workshop on safety culture, in Forsmark, Sweden

Energy Technology Data Exchange (ETDEWEB)

Eckered, T [PROMENT LTD (Sweden)

1997-09-01

The IAEA/SiP Senior Managers Workshop on International Promotion of Safety Culture for the NPPs with RBMK reactors was organized by IAEA and the Swedish International Project Nuclear Safety (SiP). It took place at the Forsmark NPP, Sweden, from 1 to 4 October 1996. The objective of the workshop were to provide a forum managers to exchange national and international experience on factors influencing safety culture, to better understand these factors and to further enhance promotion of safety culture. The Workshop participants started work by agreeing to seek the answers to the following three questions: 1. What constitutes a good Safety Culture? 2. What is good and bad in our own countries and plants from a Safety Culture point of view? 3. Where can we find advice and help from our colleagues to improve our own Safety Culture? This was the first workshop specifically addressing Safety Culture in RBMK countries. The aim was therefore not to produce good practices, but to lay a foundation for further work and development. A follow-up workshop should deepen the understanding of the SC concept and address specific SC matters identified at this Workshop.

Review of the conclusions of the 1996 workshop on safety culture, in Forsmark, Sweden

International Nuclear Information System (INIS)

Eckered, T.

1997-01-01

The IAEA/SiP Senior Managers Workshop on International Promotion of Safety Culture for the NPPs with RBMK reactors was organized by IAEA and the Swedish International Project Nuclear Safety (SiP). It took place at the Forsmark NPP, Sweden, from 1 to 4 October 1996. The objective of the workshop were to provide a forum managers to exchange national and international experience on factors influencing safety culture, to better understand these factors and to further enhance promotion of safety culture. The Workshop participants started work by agreeing to seek the answers to the following three questions: 1. What constitutes a good Safety Culture? 2. What is good and bad in our own countries and plants from a Safety Culture point of view? 3. Where can we find advice and help from our colleagues to improve our own Safety Culture? This was the first workshop specifically addressing Safety Culture in RBMK countries. The aim was therefore not to produce good practices, but to lay a foundation for further work and development. A follow-up workshop should deepen the understanding of the SC concept and address specific SC matters identified at this Workshop

A Model Proposal and Implementation Concerning Occupational Health and Safety within the Framework of World Class Manufacturing

OpenAIRE

GÜMÜŞOĞLU, Şevkinaz; TEPEKULE, Esin Tuba

2017-01-01

The approach, which aims atbecoming the best in every application and operation realizing every strategythat it has at a perfect level, has been referred to as World ClassManufacturing (WCM).  The synergic effectof WCM inherent in application and strategies will be helpful in takingbusinesses’ strength to the desired level in the current competitiveenvironment. For businesses in applications of Occupational Health and Safety(OHS) to perform at the top level will contribute to become the best,...

Lightweight hydrogen-storage material Mg0.65Sc0.35D2 studied with 2H and 2H–{45Sc} MAS NMR exchange spectroscopy

NARCIS (Netherlands)

Srinivasan, S.; Magusin, P.C.M.M.

2011-01-01

Using double-quantum 2H MAS NMR with 45Sc recoupling and Bloch–Siegert compensated 2H–{45Sc} TRAPDOR we have identified the overlapping NMR signals of deuterium with and without scandium neighbors in Mg0.65Sc0.35D2, a candidate lightweight material for hydrogen storage. At room temperature we also

Role of cell death in the propagation of PrP(Sc) in immune cells.

Science.gov (United States)

Takahashi, Kenichi; Inoshima, Yasuo; Ishiguro, Naotaka

2015-03-01

A number of studies have suggested that macrophages, dendritic cells, and follicular dendritic cells play an important role in the propagation of PrP(Sc). Both accumulation and proteolysis of PrP(Sc) have been demonstrated in peripheral macrophages. Macrophages may act as reservoirs for PrP(Sc) particles if the cells die during transient PrP(Sc) propagation. However, whether cell death plays a role in PrP(Sc) propagation in macrophages remains unclear. In this study, we investigated the possibility of propagation and transmission of PrP(Sc) between dead immune cells and living neural cells. We found that under specific conditions, transient PrP(Sc) propagation occurs in dead cells, indicating that interaction between PrP(C) and PrP(Sc) on plasma membrane lipid rafts might be important for PrP(Sc) propagation. Co-culturing of killed donor PrP(Sc)-infected macrophages with recipient N2a-3 neuroblastoma cells accelerated PrP(Sc) transmission. Our results suggest that cell death may play an important role in PrP(Sc) propagation, whereas transient PrP(Sc) propagation in macrophages has little effect on PrP(Sc) transmission.

CERN Technical Training 2004: New Short Courses (SC) on Microsoft Outlook

CERN Multimedia

Monique Duval

2004-01-01

The CERN Technical Training programme is now proposing a new format for courses on Microsoft Outlook. Three two-hours Short Courses (SC) will cover basic and advanced functionalities of the recommended mail client for email at CERN. Each module can be followed independently. The next scheduled sessions will take place as follows: Outlook (SC I): E-mail. Next session: 22.10.2004 (9h00-11h00) Outlook (SC II): Calendar, Tasks and Notes. Next session: 22.10.2004 (14h00-16h00) Outlook (SC III): Meetings and Delegation. Next session: 9.11.2004 (14h00-16h00) In particular, SC I will cover how to open, create and send email, work with attachments, use stationery, organise mail, and work with the address book, SC II will show how to work with the calendar, tasks and notes, and SC III will cover how to organise and manage meetings, work with meeting requests, share tasks, and use email and calendar delegation. The number of participants to each session is limited to 8. The instructor is English-French bilingual, and...

Problems of safety and risk in physical education

Directory of Open Access Journals (Sweden)

Robert Podstawski

2015-10-01

Full Text Available Purpose: One of the methodology issues in Physical Education is providing children with safety. The purpose of this work is to present basic concepts of safety at Physical Education classes. Material & Methods: The issues connected with safety at classes of Physical Education have been discussed in the subsections, each of which focuses on different concepts such as: legal safety regulations, causes of hazards, theoretical models of preventing hazards at P.E. classes, nutrition programs related to exercise’s fulfillment, prevention of heat disorders and dehydration. Results: According to experts’ opinion, the causes of safety hazards at P.E. classes can be divided into three groups: caused by instructor, caused by a student, and finally hazards technical in nature. The number of accidents during P.E. classes is still substantial, and among most common hazards there are the following: fractures of upper and lower limbs, dislocations, contusions, tendonitis, muscle tear and cuts. Curiously, boys experience such injuries more frequently than girls. Conclusions: Even though safety rules at Physical Education classes are defined by specific regulations, children’s absolute safety is never guaranteed. In order to diminish the number of misadventures, instructor is obliged not only to adhere to the norms but also to teach children to safety rules.

Electrochemical Characterization of Ni/(Sc)YSZ Electrodes

DEFF Research Database (Denmark)

Ramos, Tania; Thydén, Karl Tor Sune; Mogensen, Mogens Bjerg

2010-01-01

Investigations of Ni/(Sc)YSZ cermets for solid oxide cells (SOCs) were performed by electrochemical impedance spectroscopy (EIS), under varying experimental conditions and upon redox cycling, using three different designs of symmetric cells. The deconvolution and fitting of the obtained impedance...... parameters. Initial degradation results for both Ni/ScYSZ and Ni/YSZ based anodes under very high steam content are also reported. ©2010 COPYRIGHT ECS - The Electrochemical Society...

One-Step Partially Purified Lipases (ScLipA and ScLipB from Schizophyllum commune UTARA1 Obtained via Solid State Fermentation and Their Applications

Directory of Open Access Journals (Sweden)

Yew Chee Kam

2017-12-01

Full Text Available Lipases with unique characteristics are of value in industrial applications, especially those targeting cost-effectiveness and less downstream processes. The aims of this research were to: (i optimize the fermentation parameters via solid state fermentation (SSF; and (ii study the performance in hydrolysis and esterification processes of the one-step partially purified Schizophyllum commune UTARA1 lipases. Lipase was produced by cultivating S. commune UTARA1 on sugarcane bagasse (SB with used cooking oil (UCO via SSF and its production was optimized using Design-Expert® 7.0.0. Fractions 30% (ScLipA and 70% (ScLipB which contained high lipase activity were obtained by stepwise (NH42SO4 precipitation. Crude fish oil, coconut oil and butter were used to investigate the lipase hydrolysis capabilities by a free glycerol assay. Results showed that ScLipA has affinities for long, medium and short chain triglycerides, as all the oils investigated were degraded, whereas ScLipB has affinities for long chain triglycerides as it only degrades crude fish oil. During esterification, ScLipA was able to synthesize trilaurin and triacetin. Conversely, ScLipB was specific towards the formation of 2-mono-olein and triacetin. From the results obtained, it was determined that ScLipA and ScLipB are sn-2 regioselective lipases. Hence, the one-step partial purification strategy proved to be feasible for partial purification of S. commune UTARA1 lipases that has potential use in industrial applications.

Baculovirus display of single chain antibody (scFv using a novel signal peptide

Directory of Open Access Journals (Sweden)

Gonzalez Gaëlle

2010-11-01

Full Text Available Abstract Background Cells permissive to virus can become refractory to viral replication upon intracellular expression of single chain fragment variable (scFv antibodies directed towards viral structural or regulatory proteins, or virus-coded enzymes. For example, an intrabody derived from MH-SVM33, a monoclonal antibody against a conserved C-terminal epitope of the HIV-1 matrix protein (MAp17, was found to exert an inhibitory effect on HIV-1 replication. Results Two versions of MH-SVM33-derived scFv were constructed in recombinant baculoviruses (BVs and expressed in BV-infected Sf9 cells, N-myristoylation-competent scFvG2/p17 and N-myristoylation-incompetent scFvE2/p17 protein, both carrying a C-terminal HA tag. ScFvG2/p17 expression resulted in an insoluble, membrane-associated protein, whereas scFvE2/p17 was recovered in both soluble and membrane-incorporated forms. When coexpressed with the HIV-1 Pr55Gag precursor, scFvG2/p17 and scFvE2/p17 did not show any detectable negative effect on virus-like particle (VLP assembly and egress, and both failed to be encapsidated in VLP. However, soluble scFvE2/p17 isolated from Sf9 cell lysates was capable of binding to its specific antigen, in the form of a synthetic p17 peptide or as Gag polyprotein-embedded epitope. Significant amounts of scFvE2/p17 were released in the extracellular medium of BV-infected cells in high-molecular weight, pelletable form. This particulate form corresponded to BV particles displaying scFvE2/p17 molecules, inserted into the BV envelope via the scFv N-terminal region. The BV-displayed scFvE2/p17 molecules were found to be immunologically functional, as they reacted with the C-terminal epitope of MAp17. Fusion of the N-terminal 18 amino acid residues from the scFvE2/p17 sequence (N18E2 to another scFv recognizing CD147 (scFv-M6-1B9 conferred the property of BV-display to the resulting chimeric scFv-N18E2/M6. Conclusion Expression of scFvE2/p17 in insect cells using a BV

IEC SC15E: Report on liaison activities of CIGRÉ-SC15

DEFF Research Database (Denmark)

Henriksen, Mogens

2000-01-01

WG’s activities under CIGRÉ SC15:WG 15.01 - Fluid impregnated systems.WG 15.02 - Dielectric Liquids.WG 15.03 - Gas Insulation.WG 15.04 - Outdoor Insulation.WG 15.05 - Capacitors.WG 15.07 - Solid Insulating Materials for Rotating Machines.WG 15/33.08 - Insulation Monitoring and Life Estimation. WG...

Learning Low-Rank Class-Specific Dictionary and Sparse Intra-Class Variant Dictionary for Face Recognition

Science.gov (United States)

Tang, Xin; Feng, Guo-can; Li, Xiao-xin; Cai, Jia-xin

2015-01-01

Face recognition is challenging especially when the images from different persons are similar to each other due to variations in illumination, expression, and occlusion. If we have sufficient training images of each person which can span the facial variations of that person under testing conditions, sparse representation based classification (SRC) achieves very promising results. However, in many applications, face recognition often encounters the small sample size problem arising from the small number of available training images for each person. In this paper, we present a novel face recognition framework by utilizing low-rank and sparse error matrix decomposition, and sparse coding techniques (LRSE+SC). Firstly, the low-rank matrix recovery technique is applied to decompose the face images per class into a low-rank matrix and a sparse error matrix. The low-rank matrix of each individual is a class-specific dictionary and it captures the discriminative feature of this individual. The sparse error matrix represents the intra-class variations, such as illumination, expression changes. Secondly, we combine the low-rank part (representative basis) of each person into a supervised dictionary and integrate all the sparse error matrix of each individual into a within-individual variant dictionary which can be applied to represent the possible variations between the testing and training images. Then these two dictionaries are used to code the query image. The within-individual variant dictionary can be shared by all the subjects and only contribute to explain the lighting conditions, expressions, and occlusions of the query image rather than discrimination. At last, a reconstruction-based scheme is adopted for face recognition. Since the within-individual dictionary is introduced, LRSE+SC can handle the problem of the corrupted training data and the situation that not all subjects have enough samples for training. Experimental results show that our method achieves the

Learning Low-Rank Class-Specific Dictionary and Sparse Intra-Class Variant Dictionary for Face Recognition.

Science.gov (United States)

Tang, Xin; Feng, Guo-Can; Li, Xiao-Xin; Cai, Jia-Xin

2015-01-01

Face recognition is challenging especially when the images from different persons are similar to each other due to variations in illumination, expression, and occlusion. If we have sufficient training images of each person which can span the facial variations of that person under testing conditions, sparse representation based classification (SRC) achieves very promising results. However, in many applications, face recognition often encounters the small sample size problem arising from the small number of available training images for each person. In this paper, we present a novel face recognition framework by utilizing low-rank and sparse error matrix decomposition, and sparse coding techniques (LRSE+SC). Firstly, the low-rank matrix recovery technique is applied to decompose the face images per class into a low-rank matrix and a sparse error matrix. The low-rank matrix of each individual is a class-specific dictionary and it captures the discriminative feature of this individual. The sparse error matrix represents the intra-class variations, such as illumination, expression changes. Secondly, we combine the low-rank part (representative basis) of each person into a supervised dictionary and integrate all the sparse error matrix of each individual into a within-individual variant dictionary which can be applied to represent the possible variations between the testing and training images. Then these two dictionaries are used to code the query image. The within-individual variant dictionary can be shared by all the subjects and only contribute to explain the lighting conditions, expressions, and occlusions of the query image rather than discrimination. At last, a reconstruction-based scheme is adopted for face recognition. Since the within-individual dictionary is introduced, LRSE+SC can handle the problem of the corrupted training data and the situation that not all subjects have enough samples for training. Experimental results show that our method achieves the

Learning Low-Rank Class-Specific Dictionary and Sparse Intra-Class Variant Dictionary for Face Recognition.

Directory of Open Access Journals (Sweden)

Xin Tang

Full Text Available Face recognition is challenging especially when the images from different persons are similar to each other due to variations in illumination, expression, and occlusion. If we have sufficient training images of each person which can span the facial variations of that person under testing conditions, sparse representation based classification (SRC achieves very promising results. However, in many applications, face recognition often encounters the small sample size problem arising from the small number of available training images for each person. In this paper, we present a novel face recognition framework by utilizing low-rank and sparse error matrix decomposition, and sparse coding techniques (LRSE+SC. Firstly, the low-rank matrix recovery technique is applied to decompose the face images per class into a low-rank matrix and a sparse error matrix. The low-rank matrix of each individual is a class-specific dictionary and it captures the discriminative feature of this individual. The sparse error matrix represents the intra-class variations, such as illumination, expression changes. Secondly, we combine the low-rank part (representative basis of each person into a supervised dictionary and integrate all the sparse error matrix of each individual into a within-individual variant dictionary which can be applied to represent the possible variations between the testing and training images. Then these two dictionaries are used to code the query image. The within-individual variant dictionary can be shared by all the subjects and only contribute to explain the lighting conditions, expressions, and occlusions of the query image rather than discrimination. At last, a reconstruction-based scheme is adopted for face recognition. Since the within-individual dictionary is introduced, LRSE+SC can handle the problem of the corrupted training data and the situation that not all subjects have enough samples for training. Experimental results show that our

Laser photoelectron spectrometry of Sc- and Y-

International Nuclear Information System (INIS)

Feigerle, C.S.; Herman, Z.; Lineberger, W.C.

1981-01-01

The photoelectron spectra of Sc - and Y - have been obtained in a crossed ion- and laser-beam experiment. Analysis of the Sc - spectrum yields two bound terms of 3d4s 2 4p configuration ( 1 D 0 and 3 D 0 ), with EA(Sc) = 0.189 +- 0.020 eV and an excited-state binding energy of 0.042 +- 0.020 eV. Similarly, the (4d5s 2 5p) 1 D 0 ground state of Y - is bound by 0.308 +- 0.012 eV and a (4d5s 2 5p) 3 D 0 excited term is bound by 0.165 +- 0.025 eV. With the determination of the bound electronic configuration of Sc - as 3d4s 2 4p, the order of filling of electron shells of the first transition series negative ions is found to be 4s 2 ep, 3d4s 2 4p, the order of filling of electron shells of the first transition series negative ions is found to be 4s 2 4p, 3d4s 2 4p, followed by 3dsup(k) 4s 2 (k = 3, 4, ..., 10). (orig.)

The SC gets ready for visitors

CERN Multimedia

Antonella Del Rosso

2012-01-01

Hall 300, which houses the Synchrocyclotron (SC), CERN’s first accelerator, is getting ready to host a brand-new exhibition. The site will be one of the stops on the new visit itineraries that will be inaugurated for the 2013 CERN Open Day.   The Synchrocyclotron through the years. Just as it did in the late 1950s, when the accelerator was first installed, the gigantic red structure of the Synchrocyclotron's magnet occupies a large part of the 300-square-metre hall. “We have completed the first phase of the project that will give the SC a new lease of life,” says Marco Silari, the project leader and a member of CERN’s Radiation Protection Group. “We have removed all the equipment that was not an integral part of the accelerator. The hall is now ready for the civil-engineering work that will precede the installation of the exhibition.” The SC was witness to a big part of the history of CERN. The accelerator produced ...

CERN Technical Training 2004: New Short Courses (SC) on Microsoft Outlook

CERN Multimedia

Monique Duval

2004-01-01

The CERN Technical Training programme is now proposing a new format for courses on Microsoft Outlook. Three two-hours Short Courses (SC) will cover basic and advanced functionalities of the recommended mail client for email at CERN. Each module can be followed independently. The next scheduled sessions will take place as follows: Outlook (SC I): E-mail. Next session: 31.8.2004 (9h00-11h00) Outlook (SC II): Calendar, Tasks and Notes. Next session: 31.8.2004 (14h00-16h00) Outlook (SC III): Meetings and Delegation. Next session: 7.9.2004 (14h00-16h00) In particular, SC I will cover how to open, create and send email, work with attachments, use stationery, organise mail, and work with the address book, SC II will show how to work with the calendar, tasks and notes, and SC III will cover how to organise and manage meetings, work with meeting requests, share tasks, and use email and calendar delegation. The number of participants to each session is limited to 8. The instructor is English-French bilingual, and she...

Aldehyde dehydrogenase 1 is a marker for normal and malignant human colonic stem cells (SC) and tracks SC overpopulation during colon tumorigenesis.

Science.gov (United States)

Huang, Emina H; Hynes, Mark J; Zhang, Tao; Ginestier, Christophe; Dontu, Gabriela; Appelman, Henry; Fields, Jeremy Z; Wicha, Max S; Boman, Bruce M

2009-04-15

Although the concept that cancers originate from stem cells (SC) is becoming scientifically accepted, mechanisms by which SC contribute to tumor initiation and progression are largely unknown. For colorectal cancer (CRC), investigation of this problem has been hindered by a paucity of specific markers for identification and isolation of SC from normal and malignant colon. Accordingly, aldehyde dehydrogenase 1 (ALDH1) was investigated as a possible marker for identifying colonic SC and for tracking them during cancer progression. Immunostaining showed that ALDH1(+) cells are sparse and limited to the normal crypt bottom, where SCs reside. During progression from normal epithelium to mutant (APC) epithelium to adenoma, ALDH1(+) cells increased in number and became distributed farther up the crypt. CD133(+) and CD44(+) cells, which are more numerous and broadly distributed in normal crypts, showed similar changes during tumorigenesis. Flow cytometric isolation of cancer cells based on enzymatic activity of ALDH (Aldefluor assay) and implantation of these cells in nonobese diabetic-severe combined immunodeficient mice (a) generated xenograft tumors (Aldefluor(-) cells did not), (b) generated them after implanting as few as 25 cells, and (c) generated them dose dependently. Further isolation of cancer cells using a second marker (CD44(+) or CD133(+) serially) only modestly increased enrichment based on tumor-initiating ability. Thus, ALDH1 seems to be a specific marker for identifying, isolating, and tracking human colonic SC during CRC development. These findings also support our original hypothesis, derived previously from mathematical modeling of crypt dynamics, that progressive colonic SC overpopulation occurs during colon tumorigenesis and drives CRC development.

Polymorphous GdScO3 as high permittivity dielectric

International Nuclear Information System (INIS)

Schäfer, A.; Rahmanizadeh, K.; Bihlmayer, G.; Luysberg, M.; Wendt, F.; Besmehn, A.; Fox, A.

2015-01-01

Four different polymorphs of GdScO 3 are assessed theoretically and experimentally with respect to their suitability as a dielectric. The calculations carried out by density functional theory reveal lattice constants, band gaps and the energies of formation of three crystal phases. Experimentally all three crystal phases and the amorphous phase can be realized as thin films by pulsed laser deposition using various growth templates. Their respective crystal structures are confirmed by X-ray diffraction and transmission electron microscopy reflecting the calculated lattice constants. X-ray photoelectron spectroscopy unveils the band gaps of the different polymorphs of GdScO 3 which are above 5 eV for all films demonstrating good insulating properties. From capacitance voltage measurements, high permittivities of up to 27 for hexagonal GdScO 3 are deduced. - Highlights: • Different epitaxial polymorph phases of GdScO 3 were grown by pulsed laser deposition. • The cubic phase of GdScO 3 is reported for the first time. • All phases are proven to be useful for the use in silicon based and III–V based microelectronic devices.

Piezoelectric coefficients and spontaneous polarization of ScAlN

International Nuclear Information System (INIS)

Caro, Miguel A; Laurila, Tomi; Zhang, Siyuan; Moram, Michelle A; Riekkinen, Tommi; Ylilammi, Markku; Molarius, Jyrki; Lopez-Acevedo, Olga

2015-01-01

We present a computational study of spontaneous polarization and piezoelectricity in Sc x Al 1−x N alloys in the compositional range from x = 0 to x = 0.5, obtained in the context of density functional theory and the Berry-phase theory of electric polarization using large periodic supercells. We report composition-dependent values of piezoelectric coefficients e ij , piezoelectric moduli d ij and elastic constants C ij . The theoretical findings are complemented with experimental measurement of e 33 for a series of sputtered ScAlN films carried out with a piezoelectric resonator. The rapid increase with Sc content of the piezoelectric response reported in previous studies is confirmed for the available data. A detailed description of the full methodology required to calculate the piezoelectric properties of ScAlN, with application to other complex alloys, is presented. In particular, we find that the large amount of internal strain present in ScAlN and its intricate relation with electric polarization make configurational sampling and the use of large supercells at different compositions necessary in order to accurately derive the piezoelectric response of the material. (paper)

The SC15 protein of Schizophyllum commune mediates formation of aerial hyphae and attachment in the absence of the SC3 hydrophobin

NARCIS (Netherlands)

Lugones, L G; de Jong, J F; de Vries, O M H; Jalving, R; Dijksterhuis, J; Wösten, H A B

Disruption of the SC3 gene in the basidiomycete Schizophyllum commune affected not only formation of aerial hyphae but also attachment to hydrophobic surfaces. However, these processes were not completely abolished, indicating involvement of other molecules. We here show that the SC15 protein

FRACTIONAL RECRYSTALLIZATION KINETICS IN DIRECTLY COLD ROLLED Al-Mg, Al-Mg-Sc AND Al-Mg-Sc-Zr ALLOY

Directory of Open Access Journals (Sweden)

M. S. Kaiser

2014-12-01

Full Text Available The evaluation of texture as a function of recrystallization has been characterized for directly cold rolled Al-6Mg, Al-6Mg-0.4Sc and Al-6Mg-0.4Sc-0.2Zr alloys. Samples were annealed isothermally at 400 °C for 1 to 240 minutes to allow recrystallization. Recrystallization kinetics of the alloys is analyzed from the micro-hardness variation. Isothermally annealed samples of aluminum alloys were also studied using JMAK type analysis to see if there exists any correlation between the methods. Recrystallization fraction behavior between two methods the scandium added alloys show the higher variation due to precipitation hardening and higher recrystallization behavior. The scandium and zirconium as a combined shows the more variation due to formation of Al3(Sc, Zr precipitate. From the microstructure it is also observed that the base Al-Mg alloy attained almost fully re-crystallized state after annealing at 400 °C for 60 minutes

Chemical and biological evaluation of 153Sm and 46/47Sc complexes of indazolebisphosphonates for targeted radiotherapy

International Nuclear Information System (INIS)

Neves, Maria; Teixeira, Fatima C.; Antunes, Ines; Majkowska, Agnieszka; Gano, Lurdes; Santos, Ana Cristina

2011-01-01

Introduction: Novel 1-hydroxy-1,1-bisphosphonates derived from indazole and substituted at the C-3 position were labeled with the radionuclides 46 Sc and 153 Sm. Several parameters such as molar ligand concentration, pH, reaction time and temperature were studied. The radiolabelling yield, reaction kinetics and stability were assessed and radiocomplexes were evaluated by in vitro and in vivo experiments. Methods: The radionuclides 46 Sc and 153 Sm were obtained by neutron irradiation of natural Sc 2 O 3 and enriched 152 Sm 2 O 3 (98.4%) targets at the neutron flux of 3x10 14 n cm -2 s -1 . The radiolabelling yield, reaction kinetics and stability were accomplished by ascending instant thin layer chromatography. The radiocomplexes were submitted to in vitro experiments (hydroxyapatite binding and lipophilicity) and biodistribution studies in animal models. Results: The radionuclides 46 Sc and 153 Sm were produced with specific activities of 100 and 430 MBq mg -1 , respectively. High radiochemical yields were achieved and the hydrophilic radiocomplexes have shown high degree of binding to hydroxyapatite. Biodistribution studies at 1, 3 and 24 h of the 4 radiocomplexes under study, have showed a similar biodistribution profile with a relatively high bone uptake, slow clearance from blood and a very slow rate of total radioactivity excretion from the whole animal body. Conclusion: We have developed a new class of indazolebisphosphonates complexes with radioisotopes of samarium and scandium. All complexes have shown high degree of binding to hydroxyapatite, which could be attributed to the ionized phosphonate groups. The bone uptake and the bone-to-muscle ratios were relatively low.

Reusable libraries for safety-critical Java

DEFF Research Database (Denmark)

Rios Rivas, Juan Ricardo; Schoeberl, Martin

2014-01-01

The large collection of Java class libraries is a main factor of the success of Java. However, these libraries assume that a garbage-collected heap is used. Safety-critical Java uses scope-based memory areas instead of a garbage-collected heap. Therefore, the Java class libraries are problematic...... to use in safety-critical Java. We have identified common programming patterns in the Java class libraries that make them unsuitable for safety-critical Java. We propose ways to improve the libraries to avoid the impact of the identified problematic patterns. We illustrate these changes by implementing...

Creep properties and precipitate evolution in Al-Li alloys microalloyed with Sc and Yb

Energy Technology Data Exchange (ETDEWEB)

Krug, Matthew E. [Department of Materials Science and Engineering, Northwestern University, 2220 Campus Drive, Evanston, IL 60208 (United States); Seidman, David N. [Department of Materials Science and Engineering, Northwestern University, 2220 Campus Drive, Evanston, IL 60208 (United States); Northwestern Center for Atom Probe Tomography, Northwestern University, 2220 Campus Drive, Evanston, IL 60208 (United States); Dunand, David C., E-mail: dunand@northwestern.edu [Department of Materials Science and Engineering, Northwestern University, 2220 Campus Drive, Evanston, IL 60208 (United States)

2012-07-30

Highlights: Black-Right-Pointing-Pointer We examine the creep behavior of Al-alloys with Li and rare earth element additions. Black-Right-Pointing-Pointer These alloys exhibit threshold stresses below which no measurable creep occurs. Black-Right-Pointing-Pointer Larger precipitate size and lattice parameter mismatch increase creep resistance. Black-Right-Pointing-Pointer A simple parameter describes the threshold stress behavior in ternary Al-Sc-X alloys. Black-Right-Pointing-Pointer The findings are explained by a recent model of dislocation-precipitate interactions. - Abstract: A dilute Al-Sc alloy (Al-0.12 Sc, at.%, Al-Sc), its counterpart with a Li addition (Al-2.9 Li-0.11 Sc, at.%, Al-Li-Sc), as well as a quaternary alloy (Al-5.53 Li-0.048 Sc-0.009 Yb, at.%, Al-Li-Sc-Yb) were isothermally aged at 325 Degree-Sign C, and in some cases isochronally aged to 450 Degree-Sign C. As the {alpha} Prime -Al{sub 3}(Li,Sc) and Al{sub 3}(Li,Sc,Yb) precipitates, with L1{sub 2} structure, coarsen in the two Li-containing alloys, their Li and Yb concentrations decrease and their Sc concentration increases. A significant interfacial excess of Li also segregates at the {alpha}-Al matrix/{alpha} Prime -Al{sub 3}Sc(Li,Sc,Yb) precipitate interface: 5.99 {+-} 0.05 atoms nm{sup -2} in Al-Li-Sc and 13.2 {+-} 0.4 atoms nm{sup -2} in Al-Li-Sc-Yb after aging isochronally to 450 Degree-Sign C. During compression creep at 300 Degree-Sign C, the aged alloys exhibit threshold stresses between 8 and 22 MPa. A recent threshold stress model based on elastic interactions between dislocations and precipitates predicts correctly that Li additions in the Al-Li-Sc alloy reduce the threshold stress, while Yb in the Al-Li-Sc-Yb alloy increases it. The model is also in agreement with the threshold stresses of all Al-Sc-X alloys published to date.

Safety and Efficacy of AAV Retrograde Pancreatic Ductal Gene Delivery in Normal and Pancreatic Cancer Mice.

Science.gov (United States)

Quirin, Kayla A; Kwon, Jason J; Alioufi, Arafat; Factora, Tricia; Temm, Constance J; Jacobsen, Max; Sandusky, George E; Shontz, Kim; Chicoine, Louis G; Clark, K Reed; Mendell, Joshua T; Korc, Murray; Kota, Janaiah

2018-03-16

Recombinant adeno-associated virus (rAAV)-mediated gene delivery shows promise to transduce the pancreas, but safety/efficacy in a neoplastic context is not well established. To identify an ideal AAV serotype, route, and vector dose and assess safety, we have investigated the use of three AAV serotypes (6, 8, and 9) expressing GFP in a self-complementary (sc) AAV vector under an EF1α promoter (scAAV.GFP) following systemic or retrograde pancreatic intraductal delivery. Systemic delivery of scAAV9.GFP transduced the pancreas with high efficiency, but gene expression did not exceed >45% with the highest dose, 5 × 10 12 viral genomes (vg). Intraductal delivery of 1 × 10 11 vg scAAV6.GFP transduced acini, ductal cells, and islet cells with >50%, ∼48%, and >80% efficiency, respectively, and >80% pancreatic transduction was achieved with 5 × 10 11 vg. In a Kras G12D -driven pancreatic cancer mouse model, intraductal delivery of scAAV6.GFP targeted acini, epithelial, and stromal cells and exhibited persistent gene expression 5 months post-delivery. In normal mice, intraductal delivery induced a transient increase in serum amylase/lipase that resolved within a day of infusion with no sustained pancreatic inflammation or fibrosis. Similarly, in PDAC mice, intraductal delivery did not increase pancreatic intraepithelial neoplasia progression/fibrosis. Our study demonstrates that scAAV6 targets the pancreas/neoplasm efficiently and safely via retrograde pancreatic intraductal delivery.

Safety and Efficacy of AAV Retrograde Pancreatic Ductal Gene Delivery in Normal and Pancreatic Cancer Mice

Directory of Open Access Journals (Sweden)

Kayla A. Quirin

2018-03-01

Full Text Available Recombinant adeno-associated virus (rAAV-mediated gene delivery shows promise to transduce the pancreas, but safety/efficacy in a neoplastic context is not well established. To identify an ideal AAV serotype, route, and vector dose and assess safety, we have investigated the use of three AAV serotypes (6, 8, and 9 expressing GFP in a self-complementary (sc AAV vector under an EF1α promoter (scAAV.GFP following systemic or retrograde pancreatic intraductal delivery. Systemic delivery of scAAV9.GFP transduced the pancreas with high efficiency, but gene expression did not exceed >45% with the highest dose, 5 × 1012 viral genomes (vg. Intraductal delivery of 1 × 1011 vg scAAV6.GFP transduced acini, ductal cells, and islet cells with >50%, ∼48%, and >80% efficiency, respectively, and >80% pancreatic transduction was achieved with 5 × 1011 vg. In a KrasG12D-driven pancreatic cancer mouse model, intraductal delivery of scAAV6.GFP targeted acini, epithelial, and stromal cells and exhibited persistent gene expression 5 months post-delivery. In normal mice, intraductal delivery induced a transient increase in serum amylase/lipase that resolved within a day of infusion with no sustained pancreatic inflammation or fibrosis. Similarly, in PDAC mice, intraductal delivery did not increase pancreatic intraepithelial neoplasia progression/fibrosis. Our study demonstrates that scAAV6 targets the pancreas/neoplasm efficiently and safely via retrograde pancreatic intraductal delivery.

Local Impact Simulation of SC Wall Structures using Aircraft Engine Projectile

International Nuclear Information System (INIS)

Chung, Chulhun; Lee, Jungwhee; Lee, Hanjoo; Jung, Raeyoung; Hyun, Changhun

2013-01-01

SC wall structure developed for nuclear power plant buildings consists of plain concrete and two steel plates on both surface of the concrete, while RC structure consists of re bar and concrete. SC structure has higher scabbing resistance than RC structure due to the action of steel plate on the rear side of impact. Therefore SC structure is known as more effective structure from the viewpoint of aircraft crash than RC structure. However, most of the recent researches and experiments about local impact damage deal with RC structures, and the effect of re bar and steel plate is not considered reasonably. Although Walter et al. and Make-work et al. suggested a formula for evaluating perforation depth of steel plate covered RC walls, most of the previous researches about SC structure are focused on perforation and scabbing due to the impact of hard projectile, rather than soft projectile such as an aircraft. In this research a soft projectile, i. e. aircraft engine, is utilized for impact simulation of RC and SC walls. To evaluate local damage of SC wall structures, parametric study with the variables of wall thickness and steel ratio of the cover plate is performed, and the results are compared with those of RC structures. Since scabbing was prevented by the steel plates, penetration mode of damage was observed in SC walls while scabbing damage was occurred in RC walls. It is confirmed that the rear steel plate not only contains concrete debris, but also reduces the internal damage of the concrete walls. Penetration depth of SC walls did not largely vary due to the increasing steel ratio, and similar results to RC walls were observed when the wall thickness is larger than a certain value since the impact resistance of SC wall is mainly governed by the thickness of concrete part. Therefore, it is expected that similar level of impact resistance to RC structure can be produced with the minimum thickness of steel plates of SC structure. According to these results, SC

LOCA analysis of SCWR-M with passive safety system

Energy Technology Data Exchange (ETDEWEB)

Liu, X.J., E-mail: xiaojingliu@sjtu.edu.cn [School of Nuclear Science and Engineering, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai 200240 (China); Fu, S.W. [Navy University of Engineering, Wuhan, Hubei (China); Xu, Z.H. [Shanghai Nuclear Engineering Research and Design Institute, Shanghai (China); Yang, Y.H. [School of Nuclear Science and Engineering, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai 200240 (China); Cheng, X. [Institute of Fusion and Nuclear Technology, Karlsruhe Institute of Technology (KIT), Kaiserstr. 12, 76131 Karlsruhe (Germany)

2013-06-15

Highlights: • Application of the ATHLET-SC code to the trans-critical analysis for SCWR. • Development of a passive safety system for SCWR-M. • Analysis of hot/cold leg LOCA behaviour with different break size. • Introduction of some mitigation measures for SCWR-M -- Abstract: A new SCWR conceptual design (mixed spectrum supercritical water cooled reactor: SCWR-M) is proposed by Shanghai Jiao Tong University (SJTU). R and D activities covering core design, safety system design and code development of SCWR-M are launched at SJTU. Safety system design and analysis is one of the key tasks during the development of SCWR-M. Considering the current advanced reactor design, a new passive safety system for SCWR-M including isolation cooling system (ICS), accumulator injection system (ACC), gravity driven cooling system (GDCS) and automatic depressurization system (ADS) is proposed. Based on the modified and preliminarily assessed system code ATHLET-SC, loss of coolant accident (LOCA) analysis for hot and cold leg is performed in this paper. Three different break sizes are analyzed to clarify the hot and cold LOCA characteristics of the SCWR-M. The influence of the break location and break size on the safety performance of SCWR-M is also concluded. Several measures to induce the core coolant flow and to mitigate core heating up are also discussed. The results achieved so far demonstrate the feasibility of the proposed passive safety system to keep the SCWR-M core at safety condition during loss of coolant accident.

Radiolabeling of DOTATOC with the long-lived positron emitter {sup 44}Sc

Energy Technology Data Exchange (ETDEWEB)

Pruszynski, Marek; Majkowska-Pilip, Agnieszka [Centre of Radiochemistry and Nuclear Chemistry, Institute of Nuclear Chemistry and Technology, Dorodna 16, 03-195 Warszawa (Poland); Loktionova, Natalia S.; Eppard, Elisabeth [Institute of Nuclear Chemistry, Johannes Gutenberg-University of Mainz, Fritz-Strassmann-Weg 2, D-55128 Mainz (Germany); Roesch, Frank, E-mail: frank.roesch@uni-mainz.de [Institute of Nuclear Chemistry, Johannes Gutenberg-University of Mainz, Fritz-Strassmann-Weg 2, D-55128 Mainz (Germany)

2012-06-15

The positron-emitting radionuclide {sup 44}Sc with a half-life of 3.97 h and a {beta}{sup +} branching of 94.3% is of potential interest for clinical PET. As so far it is available from a {sup 44}Ti/{sup 44}Sc generator in Mainz, where long-lived {sup 44}Ti decays to no-carrier-added (nca) {sup 44}Sc. The {sup 44}Sc is a trivalent metal cation and should be suitable for complexation with many well established bifunctional chelators conjugated to peptides or other molecular targeting vectors. Thus, the aim of this work was to investigate the potential of {sup 44}Sc for labeling of DOTA-conjugated peptides. DOTA-D-Phe{sup 1}-Tyr{sup 3}-octreotide (DOTATOC) was used as a model molecule to study and optimize labeling procedure. Reaction parameters such as buffer conditions, concentration of peptide, pH range, reaction temperature and time were optimized. Addition of 21 nmol of DOTATOC to {sup 44}Sc in ammonium acetate buffer pH 4.0 provided labeling yields >98% within 25 min of heating in an oil-bath at 95 Degree-Sign C. This time can be reduced to 3 min only by applying microwave supported heating. {sup 44}Sc-DOTATOC was found to be stable in 0.9% NaCl, PBS pH 7.4, fetal calf and human serums, and also in the presence of competing metal cations (Fe{sup 3+}, Ca{sup 2+}, Cu{sup 2+}, Mg{sup 2+}), as well as other ligand competitors, like EDTA and DTPA, even after almost 25 h incubation at 37 Degree-Sign C. Present study shows that nca {sup 44}Sc forms stable complexes with the macrocyclic ligand DOTA and that {sup 44}Sc-DOTATOC and analog targeting vectors may be synthesized for further preclinical and clinical investigations. - Highlights: Black-Right-Pointing-Pointer Labeling of somatostatin analouges with positron emitter {sup 44}Sc was tested. Black-Right-Pointing-Pointer DOTATOC was labeled with {sup 44}Sc isotope. Black-Right-Pointing-Pointer Optimal conditions for {sup 44}Sc-DOTATOC synthesis were found. Black-Right-Pointing-Pointer Stability of {sup 44}Sc

Measuring social capital through multivariate analyses for the IQ-SC.

Science.gov (United States)

Campos, Ana Cristina Viana; Borges, Carolina Marques; Vargas, Andréa Maria Duarte; Gomes, Viviane Elisangela; Lucas, Simone Dutra; Ferreira e Ferreira, Efigênia

2015-01-20

Social capital can be viewed as a societal process that works toward the common good as well as toward the good of the collective based on trust, reciprocity, and solidarity. Our study aimed to present two multivariate statistical analyses to examine the formation of latent classes of social capital using the IQ-SC and to identify the most important factors in building an indicator of individual social capital. A cross-sectional study was conducted in 2009 among working adolescents supported by a Brazilian NGO. The sample consisted of 363 individuals, and data were collected using the World Bank Questionnaire for measuring social capital. First, the participants were grouped by a segmentation analysis using the Two Step Cluster method based on the Euclidian distance and the centroid criteria as the criteria for aggregate answers. Using specific weights for each item, discriminant analysis was used to validate the cluster analysis in an attempt to maximize the variance among the groups with respect to the variance within the clusters. "Community participation" and "trust in one's neighbors" contributed significantly to the development of the model with two distinct discriminant functions (p < 0.001). The majority of cases (95.0%) and non-cases (93.1%) were correctly classified by discriminant analysis. The two multivariate analyses (segmentation analysis and canonical discriminant analysis), used together, can be considered good choices for measuring social capital. Our results indicate that it is possible to form three social capital groups (low, medium and high) using the IQ-SC.

Gadolinium scandium germanide, Gd2Sc3Ge4

Directory of Open Access Journals (Sweden)

Sumohan Misra

2009-04-01

Full Text Available Gd2Sc3Ge4 adopts the orthorhombic Pu5Rh4-type structure. The crystal structure contains six sites in the asymmetric unit: two sites are statistically occupied by rare-earth atoms with Gd:Sc ratios of 0.967 (4:0.033 (4 and 0.031 (3:0.969 (3, one site (.m. symmetry is occupied by Sc atoms, and three distinct sites (two of which with .m. symmetry are occupied by Ge atoms. The rare-earth atoms form two-dimensional slabs with Ge atoms occupying the trigonal-prismatic voids.

Monitor of SC beam profiles

CERN Document Server

CERN PhotoLab

1977-01-01

A high-resolution secondary emission grid for the measurement of SC beam profiles. Modern techniques of metal-ceramic bonding, developed for micro-electronics, have been used in its construction. (See Annual Report 1977 p. 105 Fig. 12.)

Performance Analysis of OFDM 60GHz System and SC-FDE 60GHz System

Directory of Open Access Journals (Sweden)

Han Xueyan

2016-01-01

Full Text Available In this paper, the performance of 60GHz wireless communication system with SC and OFDM is studied, the models of OFDM 60GHz system and SC 60GHz frequency domain equalization (SC-FDE system are established, and the bit error rate (BER performance of OFDM 60GHz system and SC-FDE 60GHz system in 802.15.3c channels is compared. The simulation results show that SC-FDE 60GHz system has a slight advantage over OFDM system in line-of-sight (LOS channels, while OFDM 60GHz system has a slight advantage over SC-FDE system in non-line-of-sight (NLOS channels. For 60GHz system, OFDM 60GHz system has a slight advantage over SC-FDE system in overcoming multipath fading, but the performance of both is close whether in the LOS or NLOS case.

Gallium-containing Heusler phases ScRh{sub 2}Ga, ScPd{sub 2}Ga, TmRh{sub 2}Ga and LuRh{sub 2}Ga. Magnetic and solid state NMR-spectroscopic characterization

Energy Technology Data Exchange (ETDEWEB)

Heletta, Lukas; Seidel, Stefan; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Benndorf, Christopher [Leipzig Univ. (Germany). Inst. fuer Mineralogie, Kristallographie und Materialwissenschaften; Eckert, Hellmut [Muenster Univ. (Germany). Inst. fuer Physikalische Chemie; Sao Paulo Univ., Sao Carlos (Brazil). Inst. of Physics

2017-10-01

The gallium-containing Heusler phases ScRh{sub 2}Ga, ScPd{sub 2}Ga, TmRh{sub 2}Ga and LuRh{sub 2}Ga have been synthesized by arc-melting of the elements followed by different annealing sequences to improve phase purity. The samples have been studied by powder X-ray diffraction. The structures of Lu{sub 0.97}Rh{sub 2}Ga{sub 1.03} (Fm3m, a=632.94(5) pm, wR2=0.0590, 46 F{sup 2} values, seven variables) and Sc{sub 0.88}Rh{sub 2}Ga{sub 1.12} (a=618.91(4) pm, wR2=0.0284, 44 F{sup 2} values, six variables) have been refined from single crystal X-ray diffractometer data. Both gallides show structural disorder through Lu/Ga and Sc/Ga mixing. Temperature dependent magnetic susceptibility measurements showed Pauli paramagnetism for ScRh{sub 2}Ga, ScPd{sub 2}Ga, and LuRh{sub 2}Ga and Curie-Weiss paramagnetism for TmRh{sub 2}Ga. {sup 45}Sc and {sup 71}Ga solid state MAS NMR spectroscopic investigations of the Sc containing compounds confirmed the site mixing effects typically observed for Heusler phases. The data indicate that the effect of mixed Sc/Ga occupancy is significantly stronger in ScRh{sub 2}Ga than in ScPd{sub 2}Ga.

PEMODELAN KONDUKTIVITAS ION DALAM STRUKTUR Li2Sc3(PO43 (Modeling Ionic Conductivity in Li2Sc3(PO43 Structure

Directory of Open Access Journals (Sweden)

Akram La Kilo

2011-11-01

Full Text Available ABSTRAK Fasa Li2Sc3(PO43 merupakan material konduktor superionik yang dapat diaplikasikan sebagai baterai yang dapat diisi ulang (rechargeable. Ion Li+ dalam struktur Li2Sc3(PO4 dapat mengalami migrasi dari posisi terisi ke posisi kosong. Penelitian ini telah memodelkan migrasi ion Li+ dalam struktur Li2Sc3(PO4 dengan menggunakan metode bond valence sum (BVS. Metode ini dapat memprediksi bilangan oksidasi suatu atom berdasarkan jarak dengan atom-atom tetangga. Source code berbasis BVS yang digunakan adalah JUMPITER yang mensimulasi efek gaya listrik eksternal yang bertindak pada ion litium sehingga nilai BVS litium dapat dipetakan terhadap jarak. Hasil simulasi menunjukkan bahwa konduksi ion Li+ dapat terjadi pada arah [010], [101], dan [120]. Namun, lintasan konduksi ion Li+ lebih mudah terjadi pada arah [120] atau bidang ab dengan nilai maksimum BVS adalah 0,982. ABSTRACT g-phase of Li2Sc3(PO43 is a lithium super ionic conductor which can be applied as a rechargeable lithium battery. Lithium ions of g-Li2Sc3(PO43 can migrate from occupied site to vacant site. In this research, simulation of Li+ ions migration in the structure of g-Li2Sc3(PO43 carried out using bond valence sum (BVS to predict the oxidation state of Li+ion based on the distance of the ion to neighboring atoms. BVS-based code used JUMPITER to simulate the effect of external electrical force acting on the lithium ions to produce the lithium BVS value which can be mapped to the distance. The simulation results shows that Li+ ion conduction can be occurred on [010], [101], and [120] directions. However, the Li ion conduction pathway occur more easily in the direction of [120] or ab plane with the BVS maximum value is 0.982.

File list: Unc.PSC.50.AllAg.EpiSC [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Unc.PSC.50.AllAg.EpiSC mm9 Unclassified Pluripotent stem cell EpiSC SRX1074917,SRX1...074905,SRX1074908 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/Unc.PSC.50.AllAg.EpiSC.bed ...

File list: Unc.PSC.05.AllAg.EpiSC [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Unc.PSC.05.AllAg.EpiSC mm9 Unclassified Pluripotent stem cell EpiSC SRX1074917,SRX1...074908,SRX1074905 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/Unc.PSC.05.AllAg.EpiSC.bed ...

File list: Unc.PSC.20.AllAg.EpiSC [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Unc.PSC.20.AllAg.EpiSC mm9 Unclassified Pluripotent stem cell EpiSC SRX1074917,SRX1...074908,SRX1074905 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/Unc.PSC.20.AllAg.EpiSC.bed ...

Phase relationship in AL-Cu-Sc alloys at 450-500 deg C

International Nuclear Information System (INIS)

Kharakterova, M.L.

1991-01-01

Al-Cu-Sc alloys containing up to 40% Cu and up to 6% Sc at 450 deg C and 500 deg C are studied using light microscopy, X-ray-spectral microanalysis, X-ray diffraction analysis, scanning electron microscopy, measurement of microhardness and electric resistance. It is determined, that in equilibrium with aluminium solid solution under the given temperature ther are Al 3 Sc, CuAl 2 phases of the respective binary systems and W (ScCu 6.6-4 Al 5.4-8 ) ternary phase. Isothermal cross sections of Al-Cu-Sc system at 450 and 500 deg C are plotted. Microhardness of equilibrium phases is measured. Combined solubility of copper and scandium in aluminium is determined

Effect of Sc addition on microstructure and mechanical properties of 1460 alloy

Directory of Open Access Journals (Sweden)

Juan Ma

2014-02-01

Full Text Available The effect of minor addition of Sc on microstructure, age hardening behavior, tensile properties and fracture morphology of 1460 alloy have been studied. It is found that Sc content increase from 0.11 wt% to 0.22 wt% is favorable for grain refinement in as-cast alloy but results in a coarsening of Cu-rich particles. The alloy with 0.11 wt% Sc exhibits enhanced mechanical properties and age hardening effect. Transmission electron microscopy (TEM investigations on the alloy with 0.11 wt% Sc have suggested that a large amount of Al3(Sc, Zr particles precipitated at the earlier aging may inhibit recrystallization effectively.

Mathematical models of some geomagnetic storms with SC

International Nuclear Information System (INIS)

Ivanova, P.K.

1990-01-01

Regressive equations for H horizontal component of three geomagnetic storms with Sc:0.1.03.82, 24.01.74 and 23.03.69 -are calculated using step-by-step regression analysis. These equations relate H with parameters of solar wind and interplanetary magnetic field. Nonlinear, square, logarithmic and trigonometric dependences are considered, as well. Most essential parameters, which contribute mostly into Sc, are determined from multiplicity (46 factors) of independent parameters

Radiation protection Group (SC/RP) desperately seeking...

CERN Document Server

A. Hervé, Y. Donjoux / SC

2006-01-01

We are trying to trace two transit permits (passavants), which constitute the customs clearance documentation for two 'AD6'portable radiation detectors. The two permits (No. 1308 and No. 1309) were sent in the same internal mail envelope towards the middle of March 2006 but never reached their final destination. After weeks of searching in vain, we are now appealing for your help. If you have these two permits in your possession, please get in touch with us. Many thanks in advance. A.HERVE - SC/RP- ( 163168 / 70927) Y.DONJOUX - SC/RP - (160105 / 73171)

[Roberts-SC phocomelia syndrome].

Science.gov (United States)

Musfeld, D A; Bühler, E M; Heinzl, S

2001-01-01

The Roberts-SC phocomelia syndrome is a rare autosomal recessive inherited disorder clinically manifested by tetraphocomelia, pre- and postnatal growth retardation, and craniofacial abnormalities (skull, eyes, lip, and palate), accompanied at times by centromer puffing and splitting, renal abnormalities, heart defect, clitoral or penile enlargement, and bilateral corneal opacities. Mental retardation is common in surviving patients.

Model of Dees and Rotco for the 600 MeV SC

CERN Multimedia

CERN PhotoLab

1978-01-01

The accelerating frequency of the 600 MeV Synchro-Cyclotron (SC) was modulated by the varying capacity of a rotating condenser ("Rotco", the most delicate component of the SC). A 1/5-scale model, dating from the design-period of the SC, was used to study improvements to the SC RF-system, and also the acceleration of ions, first Helium and, at the time of this picture, Carbon. In the middle of the picture is the case containing the Dees. To the left, at the wide end of the cone, a rotco. Reinhold Hohbach is busy with measurements. See also 7805235 (Annual Report 1978, p.110).

First coil for the SC

CERN Multimedia

CERN PhotoLab

1955-01-01

The coils for the SC magnet were stored in the large hangar of the Cointrin Airport (to make sure that they would be available before snow and ice would block the roads and canals from Belgium, where they were built).

Selecting safety standards for nuclear power plants

International Nuclear Information System (INIS)

1981-01-01

Today, many thousands of documents are available describing the requirements, guidelines, and industrial standards which can be used as bases for a nuclear power plant programme. Many of these documents relate to nuclear safety which is currently the focus of world-wide attention. The multitude of documents available on the subject, and their varying status and emphasis, make the processes of selection and implementation very important. Because nuclear power plants are technically intricate and advanced, particularly in relation to the technological status of many developing countries, these processes are also complicated. These matters were the subject of a seminar held at the Agency's headquarters in Vienna last December. The IAEA Nuclear Safety Standards (NUSS) programme was outlined and explained at the Seminar. The five areas of the NUSS programme for nuclear power plants cover, governmental organization, siting, design; operation; quality assurance. In each area the Agency has issued Codes of Practice and is developing Safety Guides. These provide regulatory agencies with a framework for safety. The Seminar recognized that the NUSS programme should enable developing countries to identify priorities in their work, particularly the implementation of safety standards. The ISO activities in the nuclear field are carried out in the framework of its Technical Committee 85 (ISO/TC85). The work is distributed in sub-committees. Seminar on selection and implementation of safety standards for nuclear power plants, jointly organized by the IAEA and the International Organization for Standardization (ISO), and held in Vienna from 15 to 18 December 1980 concerned with: terminology, definitions, units and symbols (SC-1), radiation protection (SC-2), power reactor technology (SC-3), nuclear fuel technology (SC-5). There was general agreement that the ISO standards are complementary to the NUSS codes and guides. ISO has had close relations with the IAEA for several years

Some peculiarities of ScFe2 and ScNi2 interaction with ammonia in the presence of NH4Cl

International Nuclear Information System (INIS)

Shilkin, S.P.; Fokin, V.N.; Fokina, Eh.Eh.; Tarasov, B.P.; Korobkov, I.I.

2000-01-01

Interaction of ScFe 2 and ScNi 2 intermetallic compounds with ammonia in the presence of NH 4 Cl (10 mass % from intermetallide introduced in reaction) as an activator of the process in initial ammonia pressure 0.6-0.8 MPa is investigated. Possibility of preparation of crystalline intermetallide hydrides and amorphous products in highly dispersed state at different temperature are shown. It is established that intermetallides decompose in ammonia medium at ≥ 450 Deg C [ru

Theoretical study of stability and superconductivity of ScHn (n =4 -8 ) at high pressure

Science.gov (United States)

Qian, Shifeng; Sheng, Xiaowei; Yan, Xiaozhen; Chen, Yangmei; Song, Bo

2017-09-01

The synthesis of hydrogen sulfides, with the potential of high-temperature superconductivity, was recently proposed at high Tc = 203 K. It motivated us to employ an ab initio approach for the predictions of crystal structures to find the stable scandium hydrides. In addition to the earlier predicted three stoichiometries of ScH, ScH2, and ScH3, we identify three other metallic stoichiometries of ScH4, ScH6, and ScH8, which show superconductivity at significantly higher temperatures. The phases of ScH4 and ScH6, whose stability does not require extremely high pressures (ZPE), are primarily ionic compounds containing exotic quasimolecular H2 arrangements. The present electron-phonon calculations revealed the superconductive potential of ScH4 and ScH6 with estimated Tc of 98 K and 129 K at 200 GPa and 130 GPa, respectively. The superconductivity of ScHn stems from the large electron-phonon coupling associated with the wagging, bending, and intermediate-frequency modes attributed mainly to the hydrogen atoms.

Methods for production of UNK SC-dipoles magnetic measurements

International Nuclear Information System (INIS)

Smirnov, N.L.

1991-01-01

Many SC-dipoles for UNK will require from the chosen magnetic measurement methods high accuracy and efficiency. The brief of using methods, their possibilities and analysis of their errors are given. The measurements results for a full-scale model of SC-dipole SPDM1 are presented. 5 refs.; 4 figs.; 4 tabs

Study of the hyperfine magnetic field at Ta181 site in the Heusler Co2 Sc Sn, Co2 Sc Ga and Co2 Hf Sn alloys

International Nuclear Information System (INIS)

Attili, R.N.

1992-01-01

The hyperfine magnetic fields acting on 181 Ta nuclei at the Sc and Hf sites have been measured in Heusler alloys Co 2 Sc Sn and Co 2 Sc Ga and Co 2 Hf Sn using the Time Differential Perturbed γ-γ Angular Correlation (TDPAC) technique. The measurements were carried out using an automatic spectrometer consisting of two Ba F 2 detectors and the conventional electronics. The magnitude of hyperfine magnetic field at 181 Ta was measured for all the alloys. The signs of the were determined in the cases of Co 2 Sc Sn and Co 2 Hf Sn alloys by performing the Perturbed Angular Correlation measurements with an external polarizing magnetic field of ≅ 5 k Gauss. The hyperfine magnetic fields obtained are -187,6± 3,3 and 90,0 ± 2,1 kOe measured at 77 K for Co 2 Sc Sn and Co 2 Sc Ga alloys respectively, and -342,4 ± 10,1 kOe measured at the room temperature for Co 2 Hf Sn alloy. These results are discussed and compared with the hyperfine magnetic field systematics in Co-based Heusler alloy. (author)

Class 2 piping rules in elevated temperature applications compared with Class 1 prescriptions for LMFBRs

International Nuclear Information System (INIS)

Capello, R.; Stretti, G.; Cesari, F.G.

1989-01-01

An LMFBR plant has many piping systems subjected to elevated temperature (> 427 o C) which, depending on their function and safety criteria, are classified as of quality level 1 or 2. The design of class 1 and class 2 piping for elevated temperatures is performed in accordance with ASME CCN-47 and CCN-253 respectively. This paper discusses what level of knowledge and analysis is necessary, to apply the rules of class 2 (CCN-253) rather than those of class 1 (CCN-47) for the design analysis of piping systems. From the designer viewpoint the burden of verification is much greater in class 1 than in class 2. This paper also examines the reliability of class 2 rules for elevated temperature when used to obtain structural results and justify the design of class 1 systems. In fact it can be shown that in some cases it is possible to design class 1 piping systems using class 2 rules. (author)

Level densities and γ strength functions in light Sc and Ti isotopes

International Nuclear Information System (INIS)

Burger, A.; Larsen, A.C.; Syed, N.U.H.; Guttormsen, M.; Nyhus, H.; Siem, S.; Harissopulos, S.; Konstantinopoulos, T.; Lagoyannis, A.; Perdidakis, G.; Spyrou, A.; Kmiecik, M.; Mazurek, K.; Krticka, M.; Loennroth, T.; Norby, M.; Voinov, A.

2010-01-01

We present preliminary results from a measurement of nuclear level densities and the γ-ray strength of light Sc (Sc 43 , Sc 45 ) and Ti (Ti 44 , Ti 45 and Ti 46 ) isotopes using the Oslo Method. The article begins with a presentation of the experimental setup. (authors)

Analysis of various types of single-polypeptide-chain (sc) heterodimeric A{sub 2A}R/D{sub 2}R complexes and their allosteric receptor–receptor interactions

Energy Technology Data Exchange (ETDEWEB)

Kamiya, Toshio, E-mail: kamiya@z2.keio.jp [Department of Molecular Cell Signaling, Tokyo Metropolitan Institute for Neuroscience, 2-6 Musashidai, Fuchu, Tokyo 183-8526 (Japan); Department of Neurology, Tokyo Metropolitan Institute for Neuroscience, 2-6 Musashidai, Fuchu, Tokyo 183-8526 (Japan); Cell Biology Laboratory, School of Pharmaceutical Sciences, Kinki University, 3-4-1 Kowakae, Higashi-Osaka, Osaka 577-8502 (Japan); Yoshioka, Kazuaki; Nakata, Hiroyasu [Department of Molecular Cell Signaling, Tokyo Metropolitan Institute for Neuroscience, 2-6 Musashidai, Fuchu, Tokyo 183-8526 (Japan)

2015-01-09

Highlights: • Various scA{sub 2A}R/D{sub 2}R constructs, with spacers between the two receptors, were created. • Using whole cell binding assay, constructs were examined for their binding activity. • Although the apparent ratio of A{sub 2A}R to D{sub 2}R binding sites should be 1, neither was 1. • Counter agonist-independent binding cooperativity occurred in context of scA{sub 2A}R/D{sub 2}R. - Abstract: Adenosine A{sub 2A} receptor (A{sub 2A}R) heteromerizes with dopamine D{sub 2} receptor (D{sub 2}R). However, these class A G protein-coupled receptor (GPCR) dimers are not fully formed, but depend on the equilibrium between monomer and dimer. In order to stimulate the heteromerization, we have previously shown a successful design for a fusion receptor, single-polypeptide-chain (sc) heterodimeric A{sub 2A}R/D{sub 2}R complex. Here, using whole cell binding assay, six more different scA{sub 2A}R/D{sub 2}R constructs were examined. Not only in scA{sub 2A}R/D{sub 2}R ‘liberated’ with longer spacers between the two receptors, which confer the same configuration as the prototype, the A{sub 2A}R-odr4TM-D{sub 2L}R, but differ in size (Forms 1–3), but also in scA{sub 2A}R/D{sub 2L}R (Form 6) fused with a transmembrane (TM) of another type II TM protein, instead of odr4TM, neither of their fixed stoichiometry (the apparent ratios of A{sub 2A}R to D{sub 2}R binding sites) was 1, suggesting their compact folding. This suggests that type II TM, either odr4 or another, facilitates the equilibrial process of the dimer formation between A{sub 2A}R and D{sub 2L}R, resulting in the higher-order oligomer formation from monomer of scA{sub 2A}R/D{sub 2L}R itself. Also, in the reverse type scA{sub 2A}R/D{sub 2L}R, i.e., the D{sub 2L}R-odr4TM-A{sub 2A}R, counter agonist-independent binding cooperativity (cooperative folding) was found to occur (Forms 4 and 5). In this way, the scA{sub 2A}R/D{sub 2L}R system has unveiled the cellular phenomenon as a snapshot of the

The data acquisition system (DAS) for the improved CERN SC

CERN Document Server

Beger, H; Fiebig, A; Schroot, H

1975-01-01

A digital data acquisition system (DAS) based on a minicomputer is described which registers the failure sequences in various equipment areas of the CERN synchrocyclotron (henceforward referred to as the SC). The avalanches of failure signals which occur from time to time are tapped from the alarm/security systems, time-resolved to 10 msec and recorded on a printer in order to aid SC failure diagnosis. The mechanisms of the DAS and its relation to the SC equipment are explained in some detail. All programs were constructed at assembler language level for speed and for ease of on-line program maintenance. The alarm sequences recorded have been of considerable help during the running in of the new radiofrequency system. Now that the new SC is operational, the DAS furnishes useful data from several equipment areas to the operators and engineers.

Paracyclophane functionalized with Sc and Li for hydrogen storage

Science.gov (United States)

Sathe, Rohit Y.; Dhilip Kumar, T. J.

2018-01-01

Li and Sc metals functionalized on the delocalized π -electrons of benzene rings in [2,2]paracyclophane structure are studied for hydrogen storage efficiency by using the M06 DFT functional with 6-311G(d,p) basis set. It is found that Sc and Li functionalized [2,2]paracyclophane complexes can hold up to 10 H2 molecules and 8 H2 molecules by Kubas-Niu-Jena interaction and charge polarization mechanism with hydrogen weight percentage of 11.4 and 13.5, respectively. Molecular dynamics simulation at various temperatures showed appreciable thermal stability while the chemical potential calculation at room temperature reveals that Sc functionalized [2,2]paracyclophane system will be a promising hydrogen storage material.

Switching between intravenous and subcutaneous trastuzumab: safety results from the PrefHer trial

OpenAIRE

Gligorov, Joseph; Curigliano, Giuseppe; Müller, Volkmar; Knoop, Ann; Jenkins, Valerie; Verma, Sunil; Osborne, Stuart; Lauer, Sabine; Machackova, Zuzana; Fallowfield, Lesley; Pivot, Xavier

2017-01-01

Aim: To assess the safety and tolerability of switching between subcutaneous (SC) and intravenous (IV) trastuzumab in the PrefHer study (NCT01401166).\\ud \\ud Patients and methods: Patients with HER2-positive early breast cancer completed (neo)adjuvant chemotherapy and were randomised to receive four cycles of SC trastuzumab, via single-use injection device (SID; Cohort 1) or hand-held syringe (Cohort 2), followed by four cycles of IV, or vice versa (the crossover period presented here) as par...

Toward low-cost affinity reagents: lyophilized yeast-scFv probes specific for pathogen antigens.

Directory of Open Access Journals (Sweden)

Sean A Gray

Full Text Available The generation of affinity reagents, usually monoclonal antibodies, remains a critical bottleneck in biomedical research and diagnostic test development. Recombinant antibody-like proteins such as scFv have yet to replace traditional monoclonal antibodies in antigen detection applications, in large part because of poor performance of scFv in solution. To address this limitation, we have developed assays that use whole yeast cells expressing scFv on their surfaces (yeast-scFv in place of soluble purified scFv or traditional monoclonal antibodies. In this study, a nonimmune library of human scFv displayed on the surfaces of yeast cells was screened for clones that bind to recombinant cyst proteins of Entamoeba histolytica, an enteric pathogen of humans. Selected yeast-scFv clones were stabilized by lyophilization and used in detection assay formats in which the yeast-scFv served as solid support-bound monoclonal antibodies. Specific binding of antigen to the yeast-scFv was detected by staining with rabbit polyclonal antibodies. In flow cytometry-based assays, lyophilized yeast-scFv reagents retained full binding activity and specificity for their cognate antigens after 4 weeks of storage at room temperature in the absence of desiccants or stabilizers. Because flow cytometry is not available to all potential assay users, an immunofluorescence assay was also developed that detects antigen with similar sensitivity and specificity. Antigen-specific whole-cell yeast-scFv reagents can be selected from nonimmune libraries in 2-3 weeks, produced in vast quantities, and packaged in lyophilized form for extended shelf life. Lyophilized yeast-scFv show promise as low cost, renewable alternatives to monoclonal antibodies for diagnosis and research.

Morphologies and growth mechanisms of the eutectic particles in as-cast Al-Mg-Sc alloy; Morphologien und Wachstumsmechanismen eutektischer Partikel in Al-Mg-Sc-Legierung im Gusszustand

Energy Technology Data Exchange (ETDEWEB)

Pan, Dejiang; Zhou, Shi' ang; Li, Heng [Hefei Univ. of Technology (China); Zhang, Zhen; Wu, Yucheng [Laboratories of Nonferrous Metal Material and Processing Engineering of Anhui Province, Hefei (China); Li, Ming [Anhui Jianghuai Automobile Co., Ltd, Hefei (China)

2017-04-15

Primary particles with faceted cubic morphology were produced in as-cast Al-Mg alloy due to the addition of Sc. The cross-section of the particles revealed some eutectic structure composed of multilayer of 'Al{sub 3}Sc + α-Al + Al{sub 3}Sc..'. At the cooling rate of 200 - 300 K/s, Al{sub 3}Sc primary phase nucleated initially on oxides within the melt and developed to a cubic structure with a 'cellular-dendritic' mode of growth. The formation of α-Al structural shells was attributed as a reason for the segregation of Mg-rich lamellar dendrites at later stages. A growth mechanism for multilayer structure was proposed using the results presented.

Bayesian narrowband interference mitigation in SC-FDMA

KAUST Repository

Ali, Anum; Masood, Mudassir; Al-Ghadhban, Samir; Al-Naffouri, Tareq Y.

2015-01-01

This paper presents a novel narrowband interference (NBI) mitigation scheme for SC-FDMA systems. The proposed scheme exploits the frequency domain sparsity of the unknown NBI signal and adopts a low complexity Bayesian sparse recovery procedure. In practice, however, the sparsity of the NBI is destroyed by a grid mismatch between NBI sources and SC-FDMA system. Towards this end, an accurate grid mismatch model is presented and a sparsifying transform is utilized to restore the sparsity of the unknown signal. Numerical results are presented that depict the suitability of the proposed scheme for NBI mitigation.

Bayesian narrowband interference mitigation in SC-FDMA

KAUST Repository

Ali, Anum

2015-08-12

This paper presents a novel narrowband interference (NBI) mitigation scheme for SC-FDMA systems. The proposed scheme exploits the frequency domain sparsity of the unknown NBI signal and adopts a low complexity Bayesian sparse recovery procedure. In practice, however, the sparsity of the NBI is destroyed by a grid mismatch between NBI sources and SC-FDMA system. Towards this end, an accurate grid mismatch model is presented and a sparsifying transform is utilized to restore the sparsity of the unknown signal. Numerical results are presented that depict the suitability of the proposed scheme for NBI mitigation.

Crystal Structure of Saccharomyces cerevisiae ECM4, a Xi-Class Glutathione Transferase that Reacts with Glutathionyl-(hydroquinones.

Directory of Open Access Journals (Sweden)

Mathieu Schwartz

Full Text Available Glutathionyl-hydroquinone reductases (GHRs belong to the recently characterized Xi-class of glutathione transferases (GSTXs according to unique structural properties and are present in all but animal kingdoms. The GHR ScECM4 from the yeast Saccharomyces cerevisiae has been studied since 1997 when it was found to be potentially involved in cell-wall biosynthesis. Up to now and in spite of biological studies made on this enzyme, its physiological role remains challenging. The work here reports its crystallographic study. In addition to exhibiting the general GSTX structural features, ScECM4 shows extensions including a huge loop which contributes to the quaternary assembly. These structural extensions are probably specific to Saccharomycetaceae. Soaking of ScECM4 crystals with GS-menadione results in a structure where glutathione forms a mixed disulfide bond with the cysteine 46. Solution studies confirm that ScECM4 has reductase activity for GS-menadione in presence of glutathione. Moreover, the high resolution structures allowed us to propose new roles of conserved residues of the active site to assist the cysteine 46 during the catalytic act.

Ternary scandium-rich indides Sc{sub 50}T{sub 13}In{sub 3} and Sc{sub 50}Rh{sub 13}In{sub 3}O{sub y} (T = Rh, Ir; y {approx} 8) - synthesis and crystal structure

Energy Technology Data Exchange (ETDEWEB)

Zaremba, R.; Poettgen, R. [Inst. fuer Anorganische und Analytische Chemie, Univ. Muenster (Germany)

2007-12-15

New intermetallic compounds Sc{sub 50}Rh{sub 13.3}In{sub 2.7} and Sc{sub 50}Ir{sub 13.6}In{sub 2.4} and the suboxides Sc{sub 49.2}Rh{sub 13}In{sub 3.8}O{sub 8.8} and Sc{sub 49.2}Rh{sub 13.7}In{sub 2.8}O{sub 8.0} were synthesized from the elements or with Sc{sub 2}O{sub 3} as an oxygen source, respectively, in sealed tantalum tubes in a water-cooled sample chamber of an induction furnace. They crystallize with a new cubic structure type, space group F m anti 3, a = 1772.5(6) pm, wR2 = 0.032, 1111 F{sup 2} values, 34 variables for Sc{sub 50}Rh{sub 13.3}In{sub 2.7}, a = 1766.5(6) pm, wR2 = 0.041, 745 F{sup 2} values, 34 variables for Sc{sub 50}Ir{sub 13.6}In{sub 2.4}, a = 1764.4(2) pm, wR2 = 0.044, 640 F{sup 2} values, 41 variables for Sc{sub 49.2}Rh{sub 13}In{sub 3.8}O{sub 8.8}, and a = 1761.5(6) pm, wR2 = 0.054, 740 F{sup 2} values, 42 variables for Sc{sub 49.2}Rh{sub 13.7}In{sub 2.8}O{sub 8.0}. The main structural motifs are rhodium-centered indium cubes in an fcc like arrangement in which the octahedral and tetrahedral voids are filled by In2Sc{sub 12} and In1Sc{sub 12} icosahedra, respectively, resembling a Li{sub 3}Bi-like structure. The Rh1 (Ir1) and Sc4 atoms lie between these polyhedral units. The oxygen atoms partially fill Sc{sub 6} octahedra in Sc{sub 49.2}Rh{sub 13}In{sub 3.8}O{sub 8.8} and Sc{sub 49.2}Rh{sub 13.7}In{sub 2.8}O{sub 8.0} with Sc-O distances of 214 - 230 pm. These octahedra are condensed via common edges and faces, encapsulating the In2Sc{sub 12} icosahedra. Due to the high scandium content one observes strong Sc-Sc bonding with Sc-Sc distances ranging from 303 to 362 pm in Sc{sub 49.2}Rh{sub 13}In{sub 3.8}O{sub 8.8}. The shortest distances occur for Sc-Rh (267 - 295 pm). The crystal chemical relationship with the Li{sub 3}Bi-related suboxide Ti{sub 12}Sn{sub 3}O{sub 10} is discussed. (orig.)

Sc-Decorated Porous Graphene for High-Capacity Hydrogen Storage: First-Principles Calculations.

Science.gov (United States)

Chen, Yuhong; Wang, Jing; Yuan, Lihua; Zhang, Meiling; Zhang, Cairong

2017-08-02

The generalized gradient approximation (GGA) function based on density functional theory is adopted to investigate the optimized geometrical structure, electron structure and hydrogen storage performance of Sc modified porous graphene (PG). It is found that the carbon ring center is the most stable adsorbed position for a single Sc atom on PG, and the maximum number of adsorbed H₂ molecules is four with the average adsorption energy of -0.429 eV/H₂. By adding a second Sc atom on the other side of the system, the hydrogen storage capacity of the system can be improved effectively. Two Sc atoms located on opposite sides of the PG carbon ring center hole is the most suitable hydrogen storage structure, and the hydrogen storage capacity reach a maximum 9.09 wt % at the average adsorption energy of -0.296 eV/H₂. The adsorption of H₂ molecules in the PG system is mainly attributed to orbital hybridization among H, Sc, and C atoms, and Coulomb attraction between negatively charged H₂ molecules and positively charged Sc atoms.

Establishment and characterization of Roberts syndrome and SC phocomelia model medaka (Oryzias latipes).

Science.gov (United States)

Morita, Akihiro; Nakahira, Kumiko; Hasegawa, Taeko; Uchida, Kaoru; Taniguchi, Yoshihito; Takeda, Shunichi; Toyoda, Atsushi; Sakaki, Yoshiyuki; Shimada, Atsuko; Takeda, Hiroyuki; Yanagihara, Itaru

2012-06-01

Roberts syndrome and SC phocomelia (RBS/SC) are genetic autosomal recessive syndromes caused by establishment of cohesion 1 homolog 2 ( ESCO 2) mutation. RBS/SC appear to have a variety of clinical features, even with the same mutation of the ESCO2 gene. Here, we established and genetically characterized a medaka model of RBS/SC by reverse genetics. The RBS/SC model was screened from a mutant medaka library produced by the Targeting Induced Local Lesions in Genomes method. The medaka mutant carrying the homozygous mutation at R80S in the conserved region of ESCO2 exhibited clinical variety (i.e. developmental arrest with craniofacial and chromosomal abnormalities and embryonic lethality) as characterized in RBS/SC. Moreover, widespread apoptosis and downregulation of some gene expression, including notch1a, were detected in the R80S mutant. The R80S mutant is the animal model for RBS/SC and a valuable resource that provides the opportunity to extend knowledge of ESCO2. Downregulation of some gene expression in the R80S mutant is an important clue explaining non-correlation between genotype and phenotype in RBS/SC. © 2012 The Authors Development, Growth & Differentiation © 2012 Japanese Society of Developmental Biologists.

MuSC is involved in regulating axonal fasciculation of mouse primary vestibular afferents.

Science.gov (United States)

Kawauchi, Daisuke; Kobayashi, Hiroaki; Sekine-Aizawa, Yoko; Fujita, Shinobu C; Murakami, Fujio

2003-10-01

Regulation of axonal fasciculation plays an important role in the precise patterning of neural circuits. Selective fasciculation contributes to the sorting of different types of axons and prevents the misrouting of axons. However, axons must defasciculate once they reach the target area. To study the regulation of fasciculation, we focused on the primary vestibulo-cerebellar afferents (PVAs), which show a dramatic change from fasciculated axon bundles to defasciculated individual axons at their target region, the cerebellar primordium. To understand how fasciculation and defasciculation are regulated in this system, we investigated the roles of murine SC1-related protein (MuSC), a molecule belonging to the immunoglobulin superfamily. We show: (i) by comparing 1,1'-dioctadecyl-3,3,3',3'-tetramethylindocarbocyanine perchlorate (Dil) labelling and anti-MuSC immunohistochemistry, that downregulation of MuSC in PVAs during development is concomitant with the defasciculation of PVA axons; (ii) in a binding assay with cells expressing MuSC, that MuSC has cell-adhesive activity via a homophilic binding mechanism, and this activity is increased by multimerization; and (iii) that MuSC also displays neurite outgrowth-promoting activity in vestibular ganglion cultures. These findings suggest that MuSC is involved in axonal fasciculation and its downregulation may help to initiate the defasciculation of PVAs.

Improved Soluble ScFv ELISA Screening Approach for Antibody Discovery Using Phage Display Technology.

Science.gov (United States)

Tohidkia, Mohammad R; Sepehri, Maryam; Khajeh, Shirin; Barar, Jaleh; Omidi, Yadollah

2017-09-01

Phage display technology (PDT) is a powerful tool for the isolation of recombinant antibody (Ab) fragments. Using PDT, target molecule-specific phage-Ab clones are enriched through the "biopanning" process. The individual specific binders are screened by the monoclonal scFv enzyme-linked immunosorbent assay (ELISA) that may associate with inevitable false-negative results. Thus, in this study, three strategies were investigated for optimization of the scFvs screening using Tomlinson I and J libraries, including (1) optimizing the expression of functional scFvs, (2) improving the sensitivity of ELISA, and (3) preparing different samples containing scFvs. The expression of all scFv Abs was significantly enhanced when scFv clones were cultivated in the terrific broth (TB) medium at the optimum temperature of 30 °C. The protein A-conjugated with horseradish peroxidase (HRP) was found to be a well-suited reagent for the detection of Ag-bound scFvs in comparison with either anti-c-myc Ab or the mixing procedure. Based on our findings, it seems there is no universal media supplement for an improved expression of all scFvs derived from both Tomlinson I and J libraries. We thus propose that expression of scFv fragments in a microplate scale is largely dependent on a variety of parameters, in particular the scFv clones and relevant sequences.

Organisational culture: variation across hospitals and connection to patient safety climate.

Science.gov (United States)

Speroff, T; Nwosu, S; Greevy, R; Weinger, M B; Talbot, T R; Wall, R J; Deshpande, J K; France, D J; Ely, E W; Burgess, H; Englebright, J; Williams, M V; Dittus, R S

2010-12-01

Bureaucratic organisational culture is less favourable to quality improvement, whereas organisations with group (teamwork) culture are better aligned for quality improvement. To determine if an organisational group culture shows better alignment with patient safety climate. Cross-sectional administration of questionnaires. Setting 40 Hospital Corporation of America hospitals. 1406 nurses, ancillary staff, allied staff and physicians. Competing Values Measure of Organisational Culture, Safety Attitudes Questionnaire (SAQ), Safety Climate Survey (SCSc) and Information and Analysis (IA). The Cronbach alpha was 0.81 for the group culture scale and 0.72 for the hierarchical culture scale. Group culture was positively correlated with SAQ and its subscales (from correlation coefficient r = 0.44 to 0.55, except situational recognition), ScSc (r = 0.47) and IA (r = 0.33). Hierarchical culture was negatively correlated with the SAQ scales, SCSc and IA. Among the 40 hospitals, 37.5% had a hierarchical dominant culture, 37.5% a dominant group culture and 25% a balanced culture. Group culture hospitals had significantly higher safety climate scores than hierarchical culture hospitals. The magnitude of these relationships was not affected after adjusting for provider job type and hospital characteristics. Hospitals vary in organisational culture, and the type of culture relates to the safety climate within the hospital. In combination with prior studies, these results suggest that a healthcare organisation's culture is a critical factor in the development of its patient safety climate and in the successful implementation of quality improvement initiatives.

Oversight and Influencing of Licensee Leadership and Management for Safety, Including Safety Culture - Regulatory Approaches and Methods. Proceedings of an NEA/IAEA Workshop, Chester, United Kingdom, 26-28 September 2011

International Nuclear Information System (INIS)

2012-01-01

the inquiry into the Nimrod air crash. There were also presentations by regulatory bodies on developments in their approaches to oversight of leadership and management for safety/safety culture (LMfS/SC) since the previous workshop, and by industry representatives on perceptions of regulatory approaches. The workshop programme also included structured discussion sessions, in which a set of issues were explored by small groups and then discussed in a plenary session. A pre-workshop survey of participating regulatory bodies was also conducted to obtain information on current approaches and areas for discussion. The discussions during the workshop and results of the pre-workshop survey confirmed that most regulators have further developed their approaches to LMfS/SC oversight since Chester. Key developments include: - Use of a structured framework for LMfS/SC interventions is now common. - Training for regulatory staff in LMfS/SC and intervention strategies/approaches is more prevalent. - There is increasing dialogue on LMfS/SC between regulators and licensees. - There is widespread recognition of the need to use multiple data sources and processes to build a meaningful picture of strengths and areas for improvement. - Increasing engagement is taking place at corporate levels of the licensee organisation, recognising the importance of focusing on key decision makers

The safety and clinical outcomes of chemoembolization in child-pugh class C patients with hepatocellular carcinomas

Energy Technology Data Exchange (ETDEWEB)

Choi, Tae Won; Kim, Hyo Cheol; Lee, Jeong Hoon; Yu, Su Jong; Kang, Beom Sik; Hur, Sae Beom; Lee, Myung Su; Jae, Hwan Jun; Chung, Jin Wook [Seoul National University College of Medicine, Seoul National University Hospital, Seoul (Korea, Republic of)

2015-12-15

To evaluate the safety and clinical outcomes of chemoembolization in Child-Pugh class C patients with hepatocellular carcinomas (HCC). The study comprised 55 patients with HCC who were classified as Child-Pugh class C and who underwent initial chemoembolization between January 2003 and December 2012. Selective chemoembolization was performed in all technically feasible cases to minimize procedure-related complications. All adverse events within 30 days were recorded using the Common Terminology Criteria for Adverse Events (CTCAE). The tumor response to chemoembolization was evaluated using the modified Response Evaluation Criteria In Solid Tumors. Thirty (54.5%) patients were within the Milan criteria, and 25 (45.5%) were beyond. The mortality of study subjects at 30 days was 5.5%. Major complications were observed in five (9.1%) patients who were all beyond the Milan criteria: two hepatic failures, one hepatic encephalopathy, and two CTCAE grade 3 increases in aspartate aminotransferase/alanine aminotransferase abnormality. The mean length of hospitalization was 6.3 ± 8.3 days (standard deviation), and 18 (32.7%) patients were discharged on the next day after chemoembolization. The tumor responses of the patients who met the Milan criteria were significantly higher (p = 0.014) than those of the patients who did not. The overall median survival was 7.1 months (95% confidence interval: 4.4-9.8 months). Even in patients with Child-Pugh class C, chemoembolization can be performed safely with a selective technique in selected cases with a small tumor burden.

Rotary condenser for SC2

CERN Multimedia

1975-01-01

During 1975 the SC2 performance was improved among other things by redesigning some of the elements of the ROTCO (Annual Report 1975, p. 55). The photo shows an interior wiew of the housing of the rotary condenser and of the sixteen sets of shaped stator blades.

Low-β SC linacs: past, present, and future

International Nuclear Information System (INIS)

Bollinger, L. M.

1998-01-01

This paper is a general review of superconducting low-β technology and applications from its beginning in 1969 into the near-term future. The emphasis is on studies of accelerating resonators and on SC linacs that boost the energy of heavy-ion beams from tandem electrostatic accelerators used for nuclear-physics research. Other topics are positive-ion SC injectors to replace tandems and the need for accelerating structures with β outside of the present proven range, 0.008 < β < 0.2

Impact of Minimum Driveway Spacing Policies on Safety Performance: An Integrated Traffic Micro-Simulation and Automated Conflict Analysis

Directory of Open Access Journals (Sweden)

Chu C. Minh

2014-09-01

Full Text Available A key strategy for successful access management is the adoption of driveway spacing guidelines that consider both safety and operations. The goal is to provide sufficient distance from one driveway to the next so that drivers can perceive and react to the conditions at each potential conflict point in succession. State DOTs across the country have adopted different driveway spacing standards that vary according to the access class and characteristics of the adjacent roadway, such as type of roadway, posted speed limit, and traffic volume. Utilizing the VISSIM microscopic traffic simulation tool and FHWA's Surrogate Safety Assessment Model (SSAM, this research examined safety implications of four different driveway spacing policies representing 13 states. The analysis involved calibrating the VISSIM model for an arterial roadway corridor in West Columbia, SC, and then using the calibrated model to simulate various operational changes to the corridor, including speed limits, traffic volumes, and the associated minimum driveway spacing criteria for the four different policies. SSAM was used to analyze vehicle trajectories derived from VISSIM to determine the number of conflict points. Experimental results indicate that posted speed limit and traffic volume are the primary impact factors for driveway safety, and thus, these parameters should be considered in establishing minimum driveway spacing. Findings from this study indicate that there are significant differences in safety impacts between the different driveway spacing policies adopted by various state DOTs.

SC-HTGR Performance Impact for Arid Sites

International Nuclear Information System (INIS)

Lommers, L.; Geschwindt, J.; Southworth, F.; Shahrokhi, F.

2014-01-01

The SC-HTGR provides high temperature steam which can support industrial process heat applications as well as high efficiency electricity generation. The increased generating efficiency resulting from using high steam temperature provides greater plant output than lower temperature concepts, and it also reduces the fraction of waste heat which must be rejected. This capability is particularly attractive for sites with little or no water for heat rejection. This high temperature capability provides greater flexibility for these sites, and it results in a smaller performance penalty than for lower temperature systems when dry cooling must be used. The performance of the SC-HTGR for a conventional site with wet cooling is discussed first. Then the performance for arid sites is evaluated. Dry cooling performance is evaluated for both moderately arid sites and very hot sites. Offdesign performance of the dry cooling system under extreme conditions is also considered. Finally, operating strategies are explored for sites where some cooling water may be available but only in very limited quantities. Results of these assessments confirm that the higher operating temperatures of the SC-HTGR are very beneficial for arid sites, providing significant advantages for both gross and net power generation. (author)

Technical Training: CERN Technical Training 2004 - New Short Courses (SC) on Microsoft Outlook

CERN Multimedia

Monique Duval

2004-01-01

The CERN Technical Training programme is now proposing a new format for courses on Microsoft Outlook. Three two-hours Short Courses (SC) will cover basic and advanced functionalities of the recommended mail client for email at CERN. Each module can be followed independently. The next scheduled sessions will take place as follows: Outlook (SC I): E-mail. Next session: 31.8.2004 (9h00-11h00) Outlook (SC II): Calendar, Tasks and Notes. Next session: 31.8.2004 (14h00-16h00) Outlook (SC III): Meetings and Delegation. Next session: 7.9.2004 (14h00-16h00) In particular, SC I will cover how to open, create and send email, work with attachments, use stationery, organise mail, and work with the address book, SC II will show how to work with the calendar, tasks and notes, and SC III will cover how to organise and manage meetings, work with meeting requests, share tasks, and use email and calendar delegation. The number of participants to each session is limited to 8. The instructor is English-French bilingual, and s...

Sc-Decorated Porous Graphene for High-Capacity Hydrogen Storage: First-Principles Calculations

Directory of Open Access Journals (Sweden)

Yuhong Chen

2017-08-01

Full Text Available The generalized gradient approximation (GGA function based on density functional theory is adopted to investigate the optimized geometrical structure, electron structure and hydrogen storage performance of Sc modified porous graphene (PG. It is found that the carbon ring center is the most stable adsorbed position for a single Sc atom on PG, and the maximum number of adsorbed H2 molecules is four with the average adsorption energy of −0.429 eV/H2. By adding a second Sc atom on the other side of the system, the hydrogen storage capacity of the system can be improved effectively. Two Sc atoms located on opposite sides of the PG carbon ring center hole is the most suitable hydrogen storage structure, and the hydrogen storage capacity reach a maximum 9.09 wt % at the average adsorption energy of −0.296 eV/H2. The adsorption of H2 molecules in the PG system is mainly attributed to orbital hybridization among H, Sc, and C atoms, and Coulomb attraction between negatively charged H2 molecules and positively charged Sc atoms.

Emission ability of La-Sc-Mo cathode

International Nuclear Information System (INIS)

Yang Jiancan; Nie Zuoren; Xi Xiaoli; Wang Yiman

2004-01-01

In this paper La-Sc-Mo cathode has been prepared and its electron emission ability was measured. This type of cathode shows good electron emission performance that the saturated current density is 6.74 A cm -1 and the work function is about 2.59 eV at 1300 deg. C, which is much lower than thoriated tungsten cathode (Th-W). So it is a potential cathode to replace the Th-W cathode with radioactive pollution. Surface analysis shows that good emission ability due to the 20 nm surplus La layer and the element Sc may do good to the La diffusion to the surface

Mechanical Property Characteristics of Butt-Fusion Joint of High Density Polyethylene Pipe for NPP Safety Class Application

International Nuclear Information System (INIS)

Oh, Youngjin; Kim, Kyoungsu; Lee, Seunggun; Park, Heungbae; Yu, Jeongho; Kim, Jongsung; Kim, Jeonghyun; Jang, Changheui; Choi, Sunwoong

2013-01-01

Several NPPs in United States replaced parts of sea water or raw water system pipes to HDPE (high density polyethylene) pipes, which have outstanding resistance for oxidation and seismic loading. ASME B and PV code committee developed Code Case N-755, which describes rules for the construction of Safety Class 3 polyethylene pressure piping components. Several NPP's in US proposed relief requests in order to apply Code Case N-755. Although US NRC permitted using Code Case N-755 and HDPE materials for Class 3 buried piping, their permission was limited to only 10 years because of several concerns for material performance of HDPE. US NRC's major concerns are about material properties and the quality of fusion zone of HDPE. In this study, material property tests for HDPE fusion zone are conducted with varying standard fusion procedures. Mechanical property tests for fused material for HDPE pipes were conducted. Fused material shows lower toughness than base material and fused material of lower fusion pressure shows higher toughness than that of higher fusion pressure

Luminescence and scintillation properties of XPO4:Nd3+ (X = Y, Lu, Sc, La) crystals

Science.gov (United States)

Makowski, Michał; Witkowski, Marcin E.; Drozdowski, Winicjusz; Wojtowicz, Andrzej J.; Wisniewski, Krzysztof; Boatner, Lynn A.

2018-05-01

Due to their very fast short-wavelength emission, neodymium-doped materials are a subject of current interest as potential scintillators. Although the initial reports regarding neodymium-doped orthophosphates (in crystalline form) and their scintillation properties appeared almost twenty years ago, they remain an interesting class of materials since there is no in-depth understanding of their fundamental scintillation mechanism. In the present research, we focus on the crystalline systems: XPO4:Nd3+, where X = Y, Lu, La, Sc. The pulse height, optical absorption, radioluminescence and photoluminescence spectra were investigated and are reported here for various temperatures from 10 to 350 K. Additionally, results of both low and high temperature thermoluminescence measurements are reported in this communication.

European and International Standards on health and safety in welding

International Nuclear Information System (INIS)

Howe, A

2009-01-01

A number of European and International Standards on health and safety in welding have been published in recent years and work on several more is nearing completion. These standards have been prepared jointly by the International Standards Organization (ISO) and the European Committee for Standardization (CEN). The standards development work has mostly been led by CEN/TC 121/SC 9, with excellent technical input from experts within Europe; but work on the revision of published standards, which has recently gathered pace, is now being carried out by ISO/TC 44/SC 9, with greater international involvement. This paper gives an overview of the various standards that have been published, are being revised or are under development in this field of health and safety in welding, seeking to (i) increase international awareness of published standards, (ii) encourage wider participation in health and safety in welding standards work and (iii) obtain feedback and solicit comments on standards that are currently under development or revision. Such an initiative is particularly timely because work is currently in progress on the revision of one of the more important standards in this field, namely EN ISO 10882:2001 Health and safety in welding and allied processes- Sampling of airborne particles and gases in the operator's breathing zone - Part 1: Sampling of airborne particles.

Crystal Structure of Saccharomyces cerevisiae ECM4, a Xi-Class Glutathione Transferase that Reacts with Glutathionyl-(hydro)quinones

Science.gov (United States)

Schwartz, Mathieu; Didierjean, Claude; Hecker, Arnaud; Girardet, Jean-Michel; Morel-Rouhier, Mélanie; Gelhaye, Eric; Favier, Frédérique

2016-01-01

Glutathionyl-hydroquinone reductases (GHRs) belong to the recently characterized Xi-class of glutathione transferases (GSTXs) according to unique structural properties and are present in all but animal kingdoms. The GHR ScECM4 from the yeast Saccharomyces cerevisiae has been studied since 1997 when it was found to be potentially involved in cell-wall biosynthesis. Up to now and in spite of biological studies made on this enzyme, its physiological role remains challenging. The work here reports its crystallographic study. In addition to exhibiting the general GSTX structural features, ScECM4 shows extensions including a huge loop which contributes to the quaternary assembly. These structural extensions are probably specific to Saccharomycetaceae. Soaking of ScECM4 crystals with GS-menadione results in a structure where glutathione forms a mixed disulfide bond with the cysteine 46. Solution studies confirm that ScECM4 has reductase activity for GS-menadione in presence of glutathione. Moreover, the high resolution structures allowed us to propose new roles of conserved residues of the active site to assist the cysteine 46 during the catalytic act. PMID:27736955

DIMM-SC: a Dirichlet mixture model for clustering droplet-based single cell transcriptomic data.

Science.gov (United States)

Sun, Zhe; Wang, Ting; Deng, Ke; Wang, Xiao-Feng; Lafyatis, Robert; Ding, Ying; Hu, Ming; Chen, Wei

2018-01-01

Single cell transcriptome sequencing (scRNA-Seq) has become a revolutionary tool to study cellular and molecular processes at single cell resolution. Among existing technologies, the recently developed droplet-based platform enables efficient parallel processing of thousands of single cells with direct counting of transcript copies using Unique Molecular Identifier (UMI). Despite the technology advances, statistical methods and computational tools are still lacking for analyzing droplet-based scRNA-Seq data. Particularly, model-based approaches for clustering large-scale single cell transcriptomic data are still under-explored. We developed DIMM-SC, a Dirichlet Mixture Model for clustering droplet-based Single Cell transcriptomic data. This approach explicitly models UMI count data from scRNA-Seq experiments and characterizes variations across different cell clusters via a Dirichlet mixture prior. We performed comprehensive simulations to evaluate DIMM-SC and compared it with existing clustering methods such as K-means, CellTree and Seurat. In addition, we analyzed public scRNA-Seq datasets with known cluster labels and in-house scRNA-Seq datasets from a study of systemic sclerosis with prior biological knowledge to benchmark and validate DIMM-SC. Both simulation studies and real data applications demonstrated that overall, DIMM-SC achieves substantially improved clustering accuracy and much lower clustering variability compared to other existing clustering methods. More importantly, as a model-based approach, DIMM-SC is able to quantify the clustering uncertainty for each single cell, facilitating rigorous statistical inference and biological interpretations, which are typically unavailable from existing clustering methods. DIMM-SC has been implemented in a user-friendly R package with a detailed tutorial available on www.pitt.edu/∼wec47/singlecell.html. wei.chen@chp.edu or hum@ccf.org. Supplementary data are available at Bioinformatics online. © The Author

Thermoelectric performance of functionalized Sc2C MXenes

KAUST Repository

Kumar, S.; Schwingenschlö gl, Udo

2016-01-01

Functionalization of the MXene Sc2C, which has the rare property to realize semiconducting states for various functionalizations including O, F, and OH, is studied with respect to the electronic and thermal behavior. The lowest lattice thermal conductivity is obtained for OH functionalization and an additional 30% decrease can be achieved by confining the phonon mean free path to 100 nm. Despite a relatively low Seebeck coefficient, Sc2C(OH)2 is a candidate for intermediate-temperature thermoelectric applications due to compensation by a high electrical conductivity and very low lattice thermal conductivity.

Thermoelectric performance of functionalized Sc2C MXenes

KAUST Repository

Kumar, S.

2016-07-05

Functionalization of the MXene Sc2C, which has the rare property to realize semiconducting states for various functionalizations including O, F, and OH, is studied with respect to the electronic and thermal behavior. The lowest lattice thermal conductivity is obtained for OH functionalization and an additional 30% decrease can be achieved by confining the phonon mean free path to 100 nm. Despite a relatively low Seebeck coefficient, Sc2C(OH)2 is a candidate for intermediate-temperature thermoelectric applications due to compensation by a high electrical conductivity and very low lattice thermal conductivity.

Energy Levels and Radiative Rates for Transitions in F-like Sc XIII and Ne-like Sc XII and Y XXX

Directory of Open Access Journals (Sweden)

Kanti M. Aggarwal

2018-05-01

Full Text Available Energy levels, radiative rates and lifetimes are reported for F-like Sc XIII and Ne-like Sc XII and Y XXX for which the general-purpose relativistic atomic structure package (GRASP has been adopted. For all three ions, limited data exist in the literature but comparisons have been made wherever possible to assess the accuracy of the calculations. In the present work, the lowest 102, 125 and 139 levels have been considered for the respective ions. Additionally, calculations have also been performed with the flexible atomic code (FAC to (particularly confirm the accuracy of energy levels.

Characteristics of the safety climate in teams with world-class safety ...

African Journals Online (AJOL)

Accidents and incidents in the construction environment are not reduced or eliminated effectively, despite numerous efforts made to improve health and safety in the industry. An extensive field of research has been conducted on how teams in the construction environment interact to deliver a project successfully in terms of ...

Chemical and biological evaluation of {sup 153}Sm and {sup 46/47}Sc complexes of indazolebisphosphonates for targeted radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Neves, Maria, E-mail: mneves@itn.p [Instituto Tecnologico e Nuclear, Sacavem (Portugal); Teixeira, Fatima C.; Antunes, Ines [INETI-Departamento de Tecnologia de Industrias Quimicas, Lisboa (Portugal); Majkowska, Agnieszka [Institute of Nuclear Chemistry and Technology, Warsaw (Poland); Gano, Lurdes [Instituto Tecnologico e Nuclear, Sacavem (Portugal); Santos, Ana Cristina [IBB-Instituto de Biofisica e Biomatematica, Coimbra (Portugal)

2011-01-15

Introduction: Novel 1-hydroxy-1,1-bisphosphonates derived from indazole and substituted at the C-3 position were labeled with the radionuclides {sup 46}Sc and {sup 153}Sm. Several parameters such as molar ligand concentration, pH, reaction time and temperature were studied. The radiolabelling yield, reaction kinetics and stability were assessed and radiocomplexes were evaluated by in vitro and in vivo experiments. Methods: The radionuclides {sup 46}Sc and {sup 153}Sm were obtained by neutron irradiation of natural Sc{sub 2}O{sub 3} and enriched {sup 152}Sm{sub 2}O{sub 3} (98.4%) targets at the neutron flux of 3x10{sup 14} n cm{sup -2} s{sup -1}. The radiolabelling yield, reaction kinetics and stability were accomplished by ascending instant thin layer chromatography. The radiocomplexes were submitted to in vitro experiments (hydroxyapatite binding and lipophilicity) and biodistribution studies in animal models. Results: The radionuclides {sup 46}Sc and {sup 153}Sm were produced with specific activities of 100 and 430 MBq mg{sup -1}, respectively. High radiochemical yields were achieved and the hydrophilic radiocomplexes have shown high degree of binding to hydroxyapatite. Biodistribution studies at 1, 3 and 24 h of the 4 radiocomplexes under study, have showed a similar biodistribution profile with a relatively high bone uptake, slow clearance from blood and a very slow rate of total radioactivity excretion from the whole animal body. Conclusion: We have developed a new class of indazolebisphosphonates complexes with radioisotopes of samarium and scandium. All complexes have shown high degree of binding to hydroxyapatite, which could be attributed to the ionized phosphonate groups. The bone uptake and the bone-to-muscle ratios were relatively low.

A word from the DG: Improved safety at CERN

CERN Multimedia

2006-01-01

One of the important objectives of my term of office is improving safety at CERN. My consideration of safety issues over the last few months, in conjunction with the Safety Commission and the Heads of Department, has led me to define a new approach for the implementation of safety policy at CERN. It is not a question of changing the safety policy and the basic safety rules laid down in document 'Safety Policy at CERN' (SAPOCO 42) but, rather, of improving the way they are applied by clarifying the roles of everyone concerned. The existing safety policy and rules have yet to be fully implemented. Some people continue to think, for example, that safety implementation only concerns the Safety Commission (SC). In reality, as SAPOCO 42 clearly specifies, safety is the responsibility of each and every individual. This means that each person in charge of a task is also responsible for guaranteeing its safe completion by implementing all the necessary measures. To enhance the awareness of this responsibility and t...

An ideal scintillator – ZnO:Sc for sub-nanosecond pulsed radiation detection

Energy Technology Data Exchange (ETDEWEB)

Zhang, Kan, E-mail: zhangkan8414@163.com [Northwest Institute of Nuclear Technology, Xi’an 710024 (China); Ouyang, Xiaoping [Northwest Institute of Nuclear Technology, Xi’an 710024 (China); Xi’an Jiaotong University, Xi’an 710049 (China); Song, Zhaohui; Han, Hetong [Northwest Institute of Nuclear Technology, Xi’an 710024 (China); Zuo, Yanbin [China Nonferrous Metal Guilin Research Institute of Geology for Mineral Resource, Guilin 541004 (China); Guan, Xingyin [Northwest Institute of Nuclear Technology, Xi’an 710024 (China); Xi’an Jiaotong University, Xi’an 710049 (China); Tan, Xinjian; Zhang, Zichuan; Liu, Junhong [Northwest Institute of Nuclear Technology, Xi’an 710024 (China)

2014-08-21

ZnO-based scintillators are particularly well suited for use as ultrafast pulsed radiation detectors which have shown broad application prospects in various fields such as the inertial confinement fusion (ICF) diagnosis, the nuclear reaction mechanism, etc. Using the hydro-thermal method, a ZnO single-crystal doped with Scandium (ZnO:Sc) sample was prepared. As a new ZnO-based scintillator, the scintillation characteristics of ZnO:Sc have not been reported previously. In this paper, optical and scintillation characteristics of ZnO:Sc single-crystal were studied. Also a scintillation detector based on ZnO:Sc was designed. Excited by the alpha-particle, the rise time of ZnO:Sc detectors was from 162.5 to 170.7 ps, and the fall time was from 300.4 to 328.8 ps.

An ideal scintillator – ZnO:Sc for sub-nanosecond pulsed radiation detection

International Nuclear Information System (INIS)

Zhang, Kan; Ouyang, Xiaoping; Song, Zhaohui; Han, Hetong; Zuo, Yanbin; Guan, Xingyin; Tan, Xinjian; Zhang, Zichuan; Liu, Junhong

2014-01-01

ZnO-based scintillators are particularly well suited for use as ultrafast pulsed radiation detectors which have shown broad application prospects in various fields such as the inertial confinement fusion (ICF) diagnosis, the nuclear reaction mechanism, etc. Using the hydro-thermal method, a ZnO single-crystal doped with Scandium (ZnO:Sc) sample was prepared. As a new ZnO-based scintillator, the scintillation characteristics of ZnO:Sc have not been reported previously. In this paper, optical and scintillation characteristics of ZnO:Sc single-crystal were studied. Also a scintillation detector based on ZnO:Sc was designed. Excited by the alpha-particle, the rise time of ZnO:Sc detectors was from 162.5 to 170.7 ps, and the fall time was from 300.4 to 328.8 ps

Chronic hypoxia suppresses the CO2 response of solitary complex (SC) neurons from rats.

Science.gov (United States)

Nichols, Nicole L; Wilkinson, Katherine A; Powell, Frank L; Dean, Jay B; Putnam, Robert W

2009-09-30

We studied the effect of chronic hypobaric hypoxia (CHx; 10-11% O(2)) on the response to hypercapnia (15% CO(2)) of individual solitary complex (SC) neurons from adult rats. We simultaneously measured the intracellular pH and firing rate responses to hypercapnia of SC neurons in superfused medullary slices from control and CHx-adapted adult rats using the blind whole cell patch clamp technique and fluorescence imaging microscopy. We found that CHx caused the percentage of SC neurons inhibited by hypercapnia to significantly increase from about 10% up to about 30%, but did not significantly alter the percentage of SC neurons activated by hypercapnia (50% in control vs. 35% in CHx). Further, the magnitudes of the responses of SC neurons from control rats (chemosensitivity index for activated neurons of 166+/-11% and for inhibited neurons of 45+/-15%) were the same in SC neurons from CHx-adapted rats. This plasticity induced in chemosensitive SC neurons by CHx appears to involve intrinsic changes in neuronal properties since they were the same in synaptic blockade medium.

Use of antifungal Saponin SC-2 of Solanum chrysotrichum for the ...

African Journals Online (AJOL)

Fungistatic and fungicidal activity of saponin SC-2 on Candida albicans and other Candida species, fluconazole and ketoconazole resistaent strains was demostrated. SC-2-associated ultrastructural alterations in several Candida species were observed. An exploratory clinical, randomized, double-blind, and controlled ...

The role of the bimodal distribution of ultra-fine silicon phase and nano-scale V-phase (AlSi2Sc2) on spark plasma sintered hypereutectic Al–Si–Sc alloys

International Nuclear Information System (INIS)

Raghukiran, Nadimpalli; Kumar, Ravi

2016-01-01

Hypereutectic Al–Si and Al–Si–Sc alloys were spark plasma sintered from corresponding gas-atomized powders. The microstructures of the Al–Si and Al–Si–Sc alloys possessed remarkably refined silicon particles in the size range of 0.38–3.5 µm and 0.35–1.16 µm respectively in contrast to the silicon particles of size greater than 100 µm typically found in conventionally cast alloys. All the sintered alloys exhibited significant ductility of as high as 85% compressive strain without failure even with the presence of relatively higher weight fraction of the brittle silicon phase. Moreover, the Al–Si–Sc alloys have shown appreciable improvement in the compressive strength over their binary counterparts due to the presence of intermetallic compound AlSi 2 Sc 2 of size 10–20 nm distributed uniformly in the matrix of those alloys. The dry sliding pin-on-disc wear tests showed improvement in the wear performance of the sintered alloys with increase in silicon content in the alloys. Further, the Al–Si–Sc ternary alloys with relatively lesser silicon content exhibited appreciable improvement in the wear resistance over their binary counterparts. The Al–Si–Sc alloys with bimodal distribution of the strengthening phases consisting of ultra-fine (sub-micron size) silicon particles and the nano-scale AlSi 2 Sc 2 improved the strength and wear properties of the alloys while retaining significant amount of ductility.

Magnet measuring equipment of SC2

CERN Multimedia

CERN PhotoLab

1974-01-01

Checking the positioning of the magnet measuring equipment installed between the poles of SC2. The steel structure in front of the magnet is designed to house the rotary condenser and to shield it from the stray magnetic field of the accelerator.

A Study on the Determination of Power Supply Class for HVAC System in KJRR

International Nuclear Information System (INIS)

Kim, Hagtae; Kim, Minjin; Suh, Yong-Suk; Kim, Jun-Yeon; Chae, Hee-Taek

2016-01-01

The purpose of this paper is to propose an appropriate electrical class, power supply class, and operation logic for the major equipment of the HVAC system such as a Confinement Isolation Damper (CID), Fission Molybdenum Isolation Damper (FID), Air Handling Unit (AHU), Air Cleaning Unit (ACU), and Contaminated Air Purification System (CAPS) in light of their functional requirements and importance. The classification for the overall HVAC system of the KJRR is a safety class NNS, Non-Seismic category, quality class S, and electrical class Non-1E. Exceptionally, the CID and FID are safety class 3, seismic category I, and quality class Q. The electrical class for the major equipment of the HVAC system should be determined considering the operation concept during Loss of Normal Electric Power (LOEP) regardless of the safety class. In this paper, the electrical and power supply class is determined and the operation logic is proposed for the major equipment of the HVAC system for the KJRR such as the CID, FID, CAPS, ACU, and AHU. The electrical class Non-1E is determined to implement a fail closed for the enhancement of safety. The power supply class is based on the functional requirements of each equipment. The CID, FID, CAPS, and ACU are Class III, but the AHU is Class IV by reflecting the importance and electrical load. After the recovery of the power supply, there is a difference in the operation concept for the HVAC system between the reactor building and fission molybdenum production building depending on the operator's residence time. The CID and CAPS are operated manually through procedures for checking the accident status, and the FID and ACU are operated automatically without special procedures

A Study on the Determination of Power Supply Class for HVAC System in KJRR

Energy Technology Data Exchange (ETDEWEB)

Kim, Hagtae; Kim, Minjin; Suh, Yong-Suk; Kim, Jun-Yeon; Chae, Hee-Taek [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The purpose of this paper is to propose an appropriate electrical class, power supply class, and operation logic for the major equipment of the HVAC system such as a Confinement Isolation Damper (CID), Fission Molybdenum Isolation Damper (FID), Air Handling Unit (AHU), Air Cleaning Unit (ACU), and Contaminated Air Purification System (CAPS) in light of their functional requirements and importance. The classification for the overall HVAC system of the KJRR is a safety class NNS, Non-Seismic category, quality class S, and electrical class Non-1E. Exceptionally, the CID and FID are safety class 3, seismic category I, and quality class Q. The electrical class for the major equipment of the HVAC system should be determined considering the operation concept during Loss of Normal Electric Power (LOEP) regardless of the safety class. In this paper, the electrical and power supply class is determined and the operation logic is proposed for the major equipment of the HVAC system for the KJRR such as the CID, FID, CAPS, ACU, and AHU. The electrical class Non-1E is determined to implement a fail closed for the enhancement of safety. The power supply class is based on the functional requirements of each equipment. The CID, FID, CAPS, and ACU are Class III, but the AHU is Class IV by reflecting the importance and electrical load. After the recovery of the power supply, there is a difference in the operation concept for the HVAC system between the reactor building and fission molybdenum production building depending on the operator's residence time. The CID and CAPS are operated manually through procedures for checking the accident status, and the FID and ACU are operated automatically without special procedures.

Phase equilibria in the system Li2O - MoO3 - Sc2O3

International Nuclear Information System (INIS)

Safonov, V.V.; Chaban, N.G.; Porotnikov, N.V.

1984-01-01

Using the methods of DTA and X-ray phase analysis, interaction of components in the system Li 2 O-MoO 3 -Sc 2 O 3 in concentration range, adjacent to the vertex of MoO 3 , has been studied. Projection of the Li 2 MoO 4 -MoO 3 -Sc 2 (MoO 4 ) 3 system liquidus on concentrational triangle of the compositions Li 2 O-MoO 3 -Sc 2 O 3 , which consists of the fields of primary separation of Li 2 MoO 4 , Li 2 Mo 5 O 17 , Li 2 Mo 4 O 13 , MoO 3 , Sc 2 (MoO 4 ) 3 , Li 3 Sc(MoO 4 ) 3 and LiSc(MoO 4 ) 2 , is built

LHCb Data Replication During SC3

CERN Multimedia

Smith, A

2006-01-01

LHCb's participation in LCG's Service Challenge 3 involves testing the bulk data transfer infrastructure developed to allow high bandwidth distribution of data across the grid in accordance with the computing model. To enable reliable bulk replication of data, LHCb's DIRAC system has been integrated with gLite's File Transfer Service middleware component to make use of dedicated network links between LHCb computing centres. DIRAC's Data Management tools previously allowed the replication, registration and deletion of files on the grid. For SC3 supplementary functionality has been added to allow bulk replication of data (using FTS) and efficient mass registration to the LFC replica catalog.Provisional performance results have shown that the system developed can meet the expected data replication rate required by the computing model in 2007. This paper details the experience and results of integration and utilisation of DIRAC with the SC3 transfer machinery.

Mise en scène ja kertova lavastus

OpenAIRE

Bruun, Ida

2013-01-01

Tämä opinnäytetyö tutkii mise en scèneä ja lavastuksen kerronnallista vaikutusta elokuvassa. Työ on toteutettu toiminnallisena ja koostuu kirjallisesta osasta ja teososasta. Teososa on vuonna 2012 ensi-iltansa saanut fiktiivinen lyhytelokuva Varjelus. Toimin elokuvassa lavastajana ja rekvisitöörinä. Kirjallinen osuus alkaa käsittelemällä mise en scènen, eli ’näyttämöllepanon’ määritelmää ja sen syntyä elokuvalliseksi konseptiksi. Työ etenee esittelemään ja tarkastelemaan käsitteen eri vis...

Determination of NEHRP Site Class of Seismic Recording Stations in the Northwest Himalayas and Its Adjoining Area Using HVSR Method

Science.gov (United States)

Harinarayan, N. H.; Kumar, Abhishek

2018-01-01

Local site characteristics play an important role in controlling the damage pattern during earthquakes (EQs). These site characteristics may vary from simple to complex and can be estimated by various field tests. In addition, extended Nakamura's method, which uses horizontal to vertical spectral ratio (HVSR) based on available EQ records also available for site class (SC) determination. In this study, SCs for 90 recording stations which are maintained by Program for Excellence in Strong Motion Studies (PESMOS), located in the northwestern Himalayas and the adjoining areas are determined using extended Nakamura's technique. Average HVSR curves obtained at majority of the recording stations are found matching with the existing literature. Predominant frequency ( f peak) from average HVSR curve at each recording station is then used for the determination of SC. Original SC given by PESMOS is purely based on geology and not based on comprehensive soil investigation exercise. In this study, the SC, which is based on the average HVSR curves is found matching with SC given by PESMOS for a majority of recording stations. However, for considerable number of recording stations, a mismatch is also found which is consistent with the existing literature. In addition, SC based on National Earthquake Hazard Reduction Program (NEHRP) scheme is proposed based on f peak for all the 90 recording stations.

Phonon and thermodynamical properties of CuSc: A DFT study

Science.gov (United States)

Jain, Ekta; Pagare, Gitanjali; Dubey, Shubha; Sanyal, S. P.

2018-05-01

A detailed systematic theoretical investigation of phonon and thermodynamical behavior of CuSc intermetallic compound has been carried out by uing first-principles density functional theory in B2-type (CsCl) crystal structure. Phonon dispersion curve and phonon density of states (PhDOS) are studied which confirm the stability of CuSc intermetallic compound in B2 phase. It is found that PhDOS at high frequencies mostly composed of Sc states. We have also presented some temperature dependent properties such as entropy, free energy, heat capacity, internal energy and thermal displacement, which are computed under PHONON code. The various features of these quantities are discussed in detail. From these results we demonstrate that the particular intermetallic have better ductility and larger thermal expansion.

Original Research: Use of hydroxyurea and phlebotomy in pediatric patients with hemoglobin SC disease

OpenAIRE

Summarell, Carly C Ginter; Sheehan, Vivien A

2016-01-01

Hydroxyurea is an excellent therapeutic agent for the pharmacological induction of HbF in patients with sickle cell disease (SCD). However, all completed clinical trials of hydroxyurea have excluded patients with hemoglobin SC (HbSC) disease. HbSC differs significantly in pathophysiology from HbSS, as HbC does not sickle, but instead causes cellular dehydration which potentiates sickling of HbS. Many severely affected HbSC patients have been placed on hydroxyurea on a case by case basis, but ...

First-principles study of the nucleation and stability of ordered precipitates in ternary Al-Sc-Li alloys

International Nuclear Information System (INIS)

Mao, Z.; Chen, W.; Seidman, D.N.; Wolverton, C.

2011-01-01

First-principles density functional calculations are used to study the nucleation and stability of L1 2 -ordered precipitates in Al-Sc-Li alloys. For dilute Al alloys, there are three possible ordered L1 2 precipitates: Al 3 Sc, Al 3 Li and an Al 3 Sc/Al 3 Li core/shell structure. To calculate the nucleation behavior, information about bulk thermodynamics (both static total energies and vibrational free energies), interfacial energetics and coherency strain is required. The study finds the following: (1) the coherency strain energies for forming coherent interfaces between Al/Al 3 Sc, Al/Al 3 Li and Al 3 Sc/Al 3 Li are relatively small, owing to the small atomic size mismatches in these systems; (2) the sublattice site preferences of Sc and Li are calculated, and it is demonstrated that Sc and Li share the same sublattice sites in both Al 3 Sc(L1 2 ) and Al 3 Li(L1 2 ), in agreement with recent experimental results; (3) the calculated solubilities of Sc and Li in α-Al alloys are in good agreement with experimental values and, for Sc, agree well with prior first-principles results; (4) the interfacial energies for Al/Al 3 Sc, Al/Al 3 Li and Al 3 Sc/Al 3 Li for (1 0 0), (1 1 0) and (1 1 1) interfaces are calculated: the values of the Al/Al 3 Sc interfacial energies are significantly larger than those of the Al/Al 3 Li and Al 3 Sc/Al 3 Li interfaces; (5) combining the bulk and interfacial energies yields the nucleation barriers and critical radii for Al 3 Sc and Al 3 Li precipitates; and (6) the energetic stability of the Al 3 Sc/Al 3 Li core/shell structure is compared with individual Al 3 Sc and Al 3 Li nuclei, and the range of precipitate sizes for which the core/shell structure is energetically favored is determined quantitatively.

Design of SC solenoid with high homogeneity

International Nuclear Information System (INIS)

Yang Xiaoliang; Liu Zhong; Luo Min; Luo Guangyao; Kang Qiang; Tan Jie; Wu Wei

2014-01-01

A novel kind of SC (superconducting) solenoid coil is designed to satisfy the homogeneity requirement of the magnetic field. In this paper, we first calculate the current density distribution of the solenoid coil section through the linear programming method. Then a traditional solenoid and a nonrectangular section solenoid are designed to produce a central field up to 7 T with a homogeneity to the greatest extent. After comparison of the two solenoid coils designed in magnet field quality, fabrication cost and other aspects, the new design of the nonrectangular section of a solenoid coil can be realized through improving the techniques of framework fabrication and winding. Finally, the outlook and error analysis of this kind of SC magnet coil are also discussed briefly. (authors)

The stress and strain analysis research of class 1 eqnipments

International Nuclear Information System (INIS)

Ye Yuanwu; Tang Long; Wang Yueying; Qi Min; Yu Huajin

2008-01-01

The class 1 equipment is very important in the nuclear device, in the design and testing process required to carry out their stress and strain analysis, so as to ensure their safety. There are two ways to get stress and strain analysis of the class 1 equipment, the theoretical and experimental methods. Through theoretical method can get the stress and strain of the class 1 equipment, so as to provide a basis for the design of the equipment; through the experimental method to verify the accuracy of the theoretical methods and provide a basis for the safety assessment of the equipment. The main ressel of CEFR (China Experimental Fast Reactor) is the class 1 equipment. In this paper, according to the stress and strain analysis research of CEFR main vessel, the theories and expperimental methods of nuclear class 1 equipments stress and strain analysis has been described. (authors)

Impregnated cathode coated with tungsten thin film containing Sc2O3

International Nuclear Information System (INIS)

Yamamoto, S.; Taguchi, S.; Watanabe, I.; Kawase, S.

1987-01-01

An impregnated cathode of a novel structure is proposed, fabricated, and evaluated. A thin tungsten film 100--400 nm in thickness containing various amounts of Sc 2 O 3 is coated on a standard impregnated cathode composed of a porous tungsten body in which electron emissive materials are impregnated. The electron emission property measured with a diode configuration is found to be dependent on Sc 2 O 3 content and surface atom distribution. Surface atom distribution is depicted by means of Auger electron spectroscopy. For high electron emission enhancement it is necessary for Sc 2 O 3 content to be 2.5--6.5 wt. % and for a layer of the order of a monolayer in thickness composed of Ba, Sc, and O to develop on the cathode surface

Differential dynamics of splicing factor SC35 during the cell cycle

Indian Academy of Sciences (India)

Fluorescence recovery after photobleaching (FRAP) experiments revealed that the mobility of GFP-SC35 was distinct in different mitotic compartments. Interestingly, the mobility of GFP-SC35 was 3-fold higher in the cytoplasm of metaphase cells compared with interphase speckles, the nucleoplasm or MIGs. Treatment of ...

BOOK REVIEW: Assessing Sc1 for GCSE

Science.gov (United States)

Reynolds, H.

2000-01-01

It is well known that investigations that `fit' the National Curriculum or examination board criteria are few in number. The fair testing emphasis means that pupils all over the country are finding out what affects the rate of a chemical reaction, the rate of photosynthesis or, in the case of Physics, the resistance of a wire. This book focuses on nine of the most common Sc1 investigations and how to prepare for them, manage and assess them. The author, a GCSE examiner, has turned his expertise into a handbook for improving Sc1 performance in the classroom. He has produced a book that would be extremely useful to both newly qualified teachers and experienced teachers. The first aim of the book, however, is to explain the requirements of Sc1. This is done comprehensively with examples of what the jargon means in practice. By breaking down the elements of planning, obtaining evidence, analysing evidence and evaluating, it is easy to see the subtleties of the mark descriptors. At first glance there seems to be little difference between the type of scientific knowledge needed for planning at level 6 and level 8. However, the level 8 statement specifies `detailed' scientific knowledge and understanding, which would mean a student should use equations from physics or symbolic chemical equations to support their arguments. One of the most useful sections in the book details the marking problems that can arise with some investigations. For example, in an investigation into electromagnets it is difficult for students to provide sufficient relevant scientific theory to satisfy the requirements of planning at level 6. One of the problems with Sc1 is that certain requirements, such as graph plotting, are difficult for many students. This book provides exercises that can be given to students to improve those skills. Each of the nine investigations is covered in great detail. Each investigation begins with an introduction detailing the rationale for choosing it, whether students

Overview of Recent Activities on Safety Culture and Human and Organizational Factors Carried Out at the Joint Research Centre of the European Commission

International Nuclear Information System (INIS)

Stručić, M.; Manna, G.

2016-01-01

The Institute for Energy and Transport (IET) of the Joint Research Centre (JRC) of the European Commission (EC) is since more than ten years active in the field of Safety Culture (SC) and Human and Organizational Factors (HOF). Several activities related to SC and HOF have been and are carried out in the frame of the EU Nuclear Safety Clearinghouse for Operating Experience Feedback (Clearinghouse). The Clearinghouse was established in 2008 to enhance nuclear safety through the lessons learned from NPP events, and to provide help in Operational Experience Feedback (OEF) process primarily to nuclear safety Regulatory Authorities and to their Technical Support Organizations within the EU. Additionally to these activities, during the Fukushima accident, Clearinghouse has been regularly providing reports on the status and progress of the accident to the EU Regulatory Authorities. Moreover, experts, selected from the JRC staffing, were directly engaged in the EU-wide risk and safety assessments of nuclear power plants known as “the Stress Tests”.

44Sc-DOTA-BN[2-14]NH2 in comparison to 68Ga-DOTA-BN[2-14]NH2 in pre-clinical investigation. Is 44Sc a potential radionuclide for PET?

International Nuclear Information System (INIS)

Koumarianou, E.; Loktionova, N.S.; Fellner, M.; Roesch, F.; Thews, O.; Pawlak, D.; Archimandritis, S.C.; Mikolajczak, R.

2012-01-01

Aim: In the present study we demonstrate the in vitro and in vivo comparison of the 44 Sc and 68 Ga labeled DOTA-BN[2-14]NH 2 . 44 Sc is a positron emitter with a half life of 3.92 h. Hence it could be used for PET imaging with ligands requiring longer observation time than in the case of 68 Ga. Methods: The binding affinity of nat Sc-DOTA-BN[2-14]NH 2 and nat Ga-DOTA-BN[2-14]NH 2 to GRP receptors was studied in competition to [ 125 I-Tyr 4 ]-Bombesin in the human prostate cancer cell line PC-3. A preliminary biodistribution in normal rats was performed, while first microPET images were assessed in male Copenhagen rats bearing the androgen-independent Dunning R-3327-AT-1 prostate cancer tumor. Results: The affinity to GRP receptors in the PC-3 cell line was higher for nat Ga-DOTA-BN[2-14]NH 2 (IC 50 (nM)=0.85±0.06) than that of nat Sc-DOTA-BN[2-14]NH 2 (IC 50 (nM)=6.49±0.13). The internalization rate of 68 Ga labeled DOTA-BN[2-14]NH 2 was slower than that of 44 Sc, but their final internalization percents were comparable. 68 Ga-DOTA-BN[2-14]NH 2 was externalized faster than 44 Sc-DOTA-BN[2-14]NH 2 . The biodistribution of 44 Sc-DOTA-BN[2-14]NH 2 and 68 Ga-DOTA-BN[2-14]NH 2 in normal rats revealed a higher uptake in target organs and tissues of the first one while both excreted mainly through urinary tract. In microPET images both tracers were accumulated in the tumor with similar uptake patterns. Conclusions: Despite the differences in the receptor affinity both the 68 Ga- and the 44 Sc-labeled DOTA-BN[2-14]NH 2 tracers showed comparable distribution and similar time constants of uptake and elimination. Moreover no differences in tumor accumulation (neither in the overall uptake nor in the dynamics) were observed from the microPet imaging. From that perspective the use of either 44 Sc or 68 Ga for detecting tumors with GRP receptors is equivalent. - Highlights: ► In vitro and in vivo evaluation of 44 Sc- and 68 Ga-DOTA-BN[2-14]NH 2 in reference to published

New separation method of no-carrier-added {sup 47}Sc from titanium targets

Energy Technology Data Exchange (ETDEWEB)

Bartos, B.; Majkowska, A.; Kasperek, A.; Krajewski, S.; Bilewicz, A. [Institute of Nuclear Chemistry and Technology, Warszawa (Poland). Nuclear Chemistry and Radiochemistry Center

2012-07-01

Radionuclides with medium energy beta emission and a several day half-life are attractive candidates for radioimmunotherapy. Among the most promising in this category is {sup 47}Sc produced by fast neutron irradiation (E{sub n} > 1 MeV) of titanium target with high energy neutrons in {sup 47}Ti(n,p){sup 47}Sc nuclear reaction. In the previously reported production scheme the dissolution of the TiO{sub 2} target in hot concentrated H{sub 2}SO{sub 4} and evaporation of the resulting solution were the most time-consuming steps. The present paper describes new, simple and efficient production method of {sup 47}Sc, where the slow dissolution of the target is avoided. After irradiation in fast neutron flux {sup 47}TiO{sub 2} and Li{sub 2}{sup 47}TiF{sub 6} targets were dissolved in HF solutions. Next {sup 47}Sc was separated from the target using anion exchange resin Dowex 1 with 0.4 M HF + 0.06 M HNO{sub 3} solution as eluent. The eluted {sup 47}Sc was adsorbed on cation exchange resin and eluted with 0.5 M of ammonium acetate. The 47Sc separation yield in the proposed procedure is about 90% with the separation time less than 2 h. The obtained no-carrier-added {sup 47}Sc was used to label DOTATATE conjugate with 96% labeling yield. (orig.)

Enhanced hardness in epitaxial TiAlScN alloy thin films and rocksalt TiN/(Al,Sc)N superlattices

Energy Technology Data Exchange (ETDEWEB)

Saha, Bivas [School of Materials Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Birck Nanotechnology Center, Purdue University, West Lafayette, Indiana 47907 (United States); Lawrence, Samantha K.; Bahr, David F. [School of Materials Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Schroeder, Jeremy L.; Birch, Jens [Thin Film Physics Division, Department of Physics, Chemistry, and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden); Sands, Timothy D. [School of Materials Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Birck Nanotechnology Center, Purdue University, West Lafayette, Indiana 47907 (United States); School of Electrical and Computer Engineering, Purdue University, West Lafayette, Indiana 47907 (United States)

2014-10-13

High hardness TiAlN alloys for wear-resistant coatings exhibit limited lifetimes at elevated temperatures due to a cubic-AlN to hexagonal-AlN phase transformation that leads to decreasing hardness. We enhance the hardness (up to 46 GPa) and maximum operating temperature (up to 1050 °C) of TiAlN-based coatings by alloying with scandium nitride to form both an epitaxial TiAlScN alloy film and epitaxial rocksalt TiN/(Al,Sc)N superlattices on MgO substrates. The superlattice hardness increases with decreasing period thickness, which is understood by the Orowan bowing mechanism of the confined layer slip model. These results make them worthy of additional research for industrial coating applications.

Final Report: Molecular Mechanisms of Interfacial Reactivity in Near Surface and Extreme Geochemical Environments (DE-SC0009362)

Energy Technology Data Exchange (ETDEWEB)

Dixon, David A [Univ. of Alabama, Tuscaloosa, AL (United States)

2016-03-27

The prediction of the long-term stability and safety of geologic sequestration of greenhouse gases requires a detailed understanding of subsurface transport and chemical interactions between the disposed greenhouse gases and the geologic media. In this regard, mineral-fluid interactions are of prime importance since reactions that occur on or near the interface can assist in the long term sequestration of CO2 by trapping in mineral phases such as carbonates, as well as influencing the subsurface migration of the disposed fluids via creation or plugging of pores or fractures in the host rock strata. Previous research on mineral-fluid interaction for subsurface CO2 storage has focused almost entirely on the aqueous phase, i.e., reactivity with aqueous solutions or brines containing dissolved CO2. However, interactions with neat to water-saturated non-aqueous fluids are of equal if not greater importance since supercritical CO2 (scCO2) is less dense than the aqueous phase or oil which will create a buoyant scCO2 plume that ultimately will dominate the pore volume within the caprock, and the injected scCO2 will contain water soon after injection and this water can be highly reactive. Collectively, therefore, mineral interactions with water-saturated scCO2-dominated fluids are pivotal and could result in the stable sequestration of CO2 by trapping in mineral phases such as metal carbonates within otherwise permeable zones in the caprock. The primary objective is to unravel the molecular mechanisms governing the reactivity of mineral phases important in the geologic sequestration of CO2 with variably wet supercritical carbon dioxide as a function of T, P, and mineral structure using computational chemistry. This work is in close collaboration with the PNNL Geosciences effort. The focus of the work at The University of Alabama is computational studies of the formation of magnesium and calcium carbonates and oxides and their reactivity and providing computational support

Martensitic Transformation in a β-Type Mg-Sc Alloy

Science.gov (United States)

Ogawa, Yukiko; Ando, Daisuke; Sutou, Yuji; Somekawa, Hidetoshi; Koike, Junichi

2018-03-01

Recently, we found that a Mg-Sc alloy with a bcc (β) phase exhibits superelasticity and a shape memory effect at low temperature. In this work, we examined the stress-induced and thermally induced martensitic transformation of the β-type Mg-Sc alloy and investigated the crystal structure of the thermally induced martensite phase based on in situ X-ray diffraction (XRD) measurements. The lattice constants of the martensite phase were calculated to be a = 0.3285 nm, b = 0.5544 nm, and c = 0.5223 nm when we assumed that the martensite phase has an orthorhombic structure (Cmcm). Based on the lattice correspondence between a bcc and an orthorhombic structures such as that in the case of β-Ti shape memory alloys, we estimated the transformation strain of the β Mg-Sc alloy. As a result, the transformation strains along the 001, 011, and 111 directions in the β phase were calculated to be + 5.7, + 8.8, and + 3.3%, respectively.

Martensitic Transformation in a β-Type Mg-Sc Alloy

Science.gov (United States)

Ogawa, Yukiko; Ando, Daisuke; Sutou, Yuji; Somekawa, Hidetoshi; Koike, Junichi

2017-12-01

Recently, we found that a Mg-Sc alloy with a bcc (β) phase exhibits superelasticity and a shape memory effect at low temperature. In this work, we examined the stress-induced and thermally induced martensitic transformation of the β-type Mg-Sc alloy and investigated the crystal structure of the thermally induced martensite phase based on in situ X-ray diffraction (XRD) measurements. The lattice constants of the martensite phase were calculated to be a = 0.3285 nm, b = 0.5544 nm, and c = 0.5223 nm when we assumed that the martensite phase has an orthorhombic structure (Cmcm). Based on the lattice correspondence between a bcc and an orthorhombic structures such as that in the case of β-Ti shape memory alloys, we estimated the transformation strain of the β Mg-Sc alloy. As a result, the transformation strains along the 001, 011, and 111 directions in the β phase were calculated to be + 5.7, + 8.8, and + 3.3%, respectively.

The development of the code package PERMAK--3D//SC--1

International Nuclear Information System (INIS)

Bolobov, P. A.; Oleksuk, D. A.

2011-01-01

Code package PERMAK-3D//SC-1 was developed for performing pin-by-pin coupled neutronic and thermal hydraulic calculation of the core fragment of seven fuel assemblies and was designed on the basis of 3D multigroup pin-by-pin code PERMAK-3D and 3D (subchannel) thermal hydraulic code SC-1 The code package predicts axial and radial pin-by-pin power distribution and coolant parameters in stimulated region (enthalpies,, velocities,, void fractions,, boiling and DNBR margins).. The report describes some new steps in code package development. Some PERMAK-3D//SC-1 outcomes of WWER calculations are presented in the report. (Authors)

Assembly of a supercrystal (SC) of the CMS endcap electromagnetic calorimeter

CERN Multimedia

J. Williams et al., RAL

2004-01-01

The first three pictures show the insertion of the first three rows of crystals into the supercrystal SC03 on Jan. 2004 and the completion of the SC endstops. Fig. 4 shows a complete supercrystal and Fig. 5 its components (alveolar, interface plate, housing, optical fibre, insert, crystal and VPT, endstop). A set of 25 inserts is shown in Fig. 6, while Fig. 7 shows housing, interface plates and inserts. Finally, a SC rear view showing the Vacum Phototriode (VPT) wires through the inserts can be seen in Fig. 8. Fig. 9 and 10 show two supercrystals under test on Dee F and R, respectively.

Experimental Study on Temperature Behavior of SC Structures under Pure Bending

International Nuclear Information System (INIS)

Ham, K. W.; Lee, K. J.; Park, D. S.; Jeon, J. H.

2006-01-01

SC(Steel plate Concrete) module method uses steel plate instead of reinforcing bar and mold in existing RC structure. Steel plate modules are fabricated in advance, installed and poured with concrete in construction field, so construction period is remarkably shortened by SC module technique. In case of existence of temperature gap between internal and external structure surface such as spent fuel storage pool, thermal stress is taken place and as a result of it, structural strength is deteriorated. In this study, we designed three test specimens and several tests with or without temperature heating were conducted to evaluate temperature behavior of SC structures under pure bending loading condition

Final Scientific Report: DE-SC0008580

Energy Technology Data Exchange (ETDEWEB)

Seidler, Gerald T. [Univ. of Washington, Seattle, WA (United States)

2017-03-16

We report scientific, technical, and organizational accomplishments under DE-SC0008580. This includes 10 publications, 5 patent or provisional patent applications, beamtime with important results at both LCLS and APS, and new progress in understanding target design for x-ray heating experiments at x-ray heating facilities.

Observed travel times for Multiply-reflected ScS waves from a deep-focus earthquake

Directory of Open Access Journals (Sweden)

A. F. ESPISOSA

1966-06-01

Full Text Available Tlie deep-focus Argentinean earthquake of December 8
1962, generated multiply reflected ScS phases which were recorded very
clearly at stations of the IGY and the TJSC&GS standardized worldwide
networks and at Canadian stations. The data gathered from this earthquake
for the multiply-reflected ScS and sScS were used to construct the
travel times and to extend them to shorter epicentral distances. These
new data brought to light an error in published travel times for the 2(ScS
phase.

Transport of one SC coil through the village of Meyrin

CERN Multimedia

1956-01-01

In 1952, before CERN was officially founded, two accelerator projects were launched: one for an innovative accelerator to operate at an energy level unequalled at the time, the other for a more standard machine, a Synchro-Cyclotron (SC) to operate at 600 MeV. Design work on the SC was started in 1952 and carried out by teams scattered throughout Europe. Once construction began in 1954, CERN had to arrange road transport for the first of what has since been a long series of spectacular component deliveries, such as those of the machine's two magnetic coils each weighing 60 tonnes and measuring 7.2 metres in diameter. Above, one of them is seen passing through the village of Meyrin. The SC was commissioned in 1957 and was operational for 34 years!

A drought severity climatology for the Carpathian Region using Sc-PDSI

Science.gov (United States)

Antofie, Tiberiu; Naumann, Gustavo; Spinoni, Jonathan; Weynants, Melanie; Szalai, Sandor; Szentimrey, Tamas; Bihari, Zita; Vogt, Jürgen

2013-04-01

Monthly grids of the self-calibrating Palmer Drought Severity Index (Sc-PDSI) have been calculated for the period 1961-2010 for the Carpathian Region (17˚-27˚E, 44˚-50˚N) with a spatial resolution of 0.1˚x 0.1˚. Using the Sc-PDSI and the assumptions of the Palmer Drought Model (PDM), the approximated precipitation required for drought termination (achieved when the Sc-PDSI turns back above -0.5) and amelioration (achieved when the Sc-PDSI value turns back above -2.0) are computed for periods of 1, 3, 6, and 9 months. The Sc-PDSI is based on a modified version of the Palmer Drought Severity Index (PDSI), first introduced by Palmer (1965) with the intent to measure the cumulative departure (related to local normal conditions) of moisture supply and demand. Due to its empirically derived climatic characteristic (K) and duration factors - limited to U.S. climatic conditions - Wells et al. (2004) improved it and transformed the PDSI into the Sc-PDSI, which is more appropriate for spatial comparisons in different climatic regions. The Sc-PDSI is based on the supply-and-demand concept of a complex water budget system based on precipitation and temperature records and also on the soil characteristics at any location. The inputs used in this study are the Available Water Capacity of the soil (AWC) derived from the soil texture (European Soil Database of JRC) with a spatial resolution of 0.1˚x0.1˚, Potential Evapo-Transpiration (PET), and 6 hydrological parameters of the soil water balance: recharge, runoff, loss, and their potential values (used in the calculation of Palmer's constants to define the normal climate for the specific location, i.e. the so called CAFEC). PET has been computed using the 0.1˚x 0.1˚ gridded monthly precipitation and mean temperature for 1961-2010 provided by the CARPATCLIM project in the framework of the construction of a Climate Atlas for the Carpathian Region. The Sc-PDSI focuses on the monthly anomalies of the soil moisture, thus it

L-Arginine ethylester enhances in vitro amplification of PrP(Sc) in macaques with atypical L-type bovine spongiform encephalopathy and enables presymptomatic detection of PrP(Sc) in the bodily fluids.

Science.gov (United States)

Murayama, Y; Ono, F; Shimozaki, N; Shibata, H

2016-02-12

Protease-resistant, misfolded isoforms (PrP(Sc)) of a normal cellular prion protein (PrP(C)) in the bodily fluids, including blood, urine, and saliva, are expected to be useful diagnostic markers of prion diseases, and nonhuman primate models are suited for performing valid diagnostic tests for human Creutzfeldt-Jakob disease (CJD). We developed an effective amplification method for PrP(Sc) derived from macaques infected with the atypical L-type bovine spongiform encephalopathy (L-BSE) prion by using mouse brain homogenate as a substrate in the presence of polyanions and L-arginine ethylester. This method was highly sensitive and detected PrP(Sc) in infected brain homogenate diluted up to 10(10) by sequential amplification. This method in combination with PrP(Sc) precipitation by sodium phosphotungstic acid is capable of amplifying very small amounts of PrP(Sc) contained in the cerebrospinal fluid (CSF), saliva, urine, and plasma of macaques that have been intracerebrally inoculated with the L-BSE prion. Furthermore, PrP(Sc) was detectable in the saliva or urine samples as well as CSF samples obtained at the preclinical phases of the disease. Thus, our novel method may be useful for furthering the understanding of bodily fluid leakage of PrP(Sc) in nonhuman primate models. Copyright © 2016 Elsevier Inc. All rights reserved.

Verification of Safety Margins of Battery Banks Capacity of Class 1E DC System in a Nuclear Power Plant

International Nuclear Information System (INIS)

Lukman, Abdulrauf; Zhu, Oon-Pyo

2015-01-01

According to Ref 'Station blackout (SBO) is generally a plant condition with complete loss of all alternating current (AC) power from off-site sources, from the main generator and from standby AC power sources important to safety to the essential and nonessential switchgear buses. Direct current (DC) power supplies and uninterruptible AC power supplies may be available as long as batteries can supply the loads, alternate AC power supplies are available'. The above IAEA document indicated the importance of batteries during SBO. Prior to the Fukushima accident, most batteries might be designed with coping capability of four hours. However, the accident showed the need for the coping capability to be increased to at least eight hours. The purpose of this research is to verify the safety capacity margin of the nuclear qualified battery banks of class 1E DC system and test the response to SBO using the load profile of a Korean design nuclear power plant (NPP). The capacity margins of class 1E batteries of DC power system batteries in a nuclear power plant were determined using the load profile of the plant. It was observed that if appropriate manufacturer Kt data are not available, the accuracy of the battery capacity might not be accurately calculated. The result obtained shows that the batteries have the coping capability of two hours for channel A and B, and eight hours for channel C and D. Also capacity margin as show in figure show a reasonable margin for each batteries of the DC system

Correlative characterization of primary Al{sub 3}(Sc,Zr) phase in an Al–Zn–Mg based alloy

Energy Technology Data Exchange (ETDEWEB)

Li, J.H., E-mail: jie-hua.li@hotmail.com [Institute of Casting Research, Montanuniversität Leoben, A-8700 Leoben (Austria); Wiessner, M. [Materials Center Leoben Forschung GmbH, A-8700 Leoben (Austria); Albu, M. [Institute for Electron Microscopy and Nanoanalysis, Graz University of Technology, Center for Electron Microscopy (Austria); Wurster, S. [Department of Materials Physics, Montanuniversität Leoben, Erich Schmid Institute of Materials Science of the Austrian Academy of Sciences, A-8700 Leoben (Austria); Sartory, B. [Materials Center Leoben Forschung GmbH, A-8700 Leoben (Austria); Hofer, F. [Institute for Electron Microscopy and Nanoanalysis, Graz University of Technology, Center for Electron Microscopy (Austria); Schumacher, P. [Institute of Casting Research, Montanuniversität Leoben, A-8700 Leoben (Austria); Austrian Foundry Research Institute, A-8700 Leoben (Austria)

2015-04-15

Three-dimensional electron backscatter diffraction, focused ion beam, transmission electron microscopy and energy filtered transmission electron microscopy were employed to investigate the structural information of primary Al{sub 3}(Sc,Zr) phase, i.e. size, shape, element distribution and orientation relationship with the α-Al matrix. It was found that (i) most primary Al{sub 3}(Sc,Zr) phases have a cubic three-dimensional morphology, with a size of about 6–10 μm, (ii) most primary Al{sub 3}(Sc,Zr) phases are located within the α-Al matrix, and exhibit a cube to cube orientation relationship with the α-Al matrix, and (iii) a layer by layer growth was observed within primary Al{sub 3}(Sc,Zr) phases. Al, Cu, Si and Fe are enriched in the α-Al matrix between the layers of cellular eutectic Al{sub 3}(Sc,Zr) phase, while Sc, Ti and Zr are enriched in small Al{sub 3}(Sc,Zr) phases. A peritectic reaction and subsequent eutectic reaction between Al{sub 3}Sc and Al was proposed to interpret the observed layer by layer growth. This paper demonstrates that the presence of impurities (Fe, Si, Cu, Ti) in the diffusion field surrounding the growing Al{sub 3}(Sc,Zr) particle enhances the heterogeneous nucleation of Al{sub 3}(Sc,Zr) phases. - Highlights: • Most fine cubic primary Al{sub 3}(Sc,Zr) phases were observed within the α-Al matrix. • A layer by layer growth within primary Al{sub 3}(Sc,Zr) phase was observed. • A peritectic and subsequent eutectic reaction between Al{sub 3}Sc and Al was proposed. • Impurities in diffusion fields enhance heterogeneous nucleation of Al{sub 3}(Sc,Zr)

Lanthanide-doped NaScF4 nanoprobes: crystal structure, optical spectroscopy and biodetection.

Science.gov (United States)

Ai, Yu; Tu, Datao; Zheng, Wei; Liu, Yongsheng; Kong, Jintao; Hu, Ping; Chen, Zhuo; Huang, Mingdong; Chen, Xueyuan

2013-07-21

Trivalent lanthanide ions (Ln(3+))-doped inorganic nanoparticles (NPs) as potential luminescent bioprobes have been attracting tremendous interest because of their unique upconversion (UC) and downconversion (DC) luminescence properties. NaScF4, as an important host material, has been rarely reported and its crystal structure remains unclear. Herein, based on the single crystal X-ray diffraction, the space group of NaScF4 crystals was determined to be P31 containing multiple sites of Sc(3+) with crystallographic site symmetry of C1, which was verified by high-resolution photoluminescence spectroscopy of Eu(3+) at low temperature (10 K). Furthermore, monodisperse and size-controllable NaScF4:Ln(3+) NPs were synthesized via a facile thermal decomposition method. The biotinylated NaScF4:Er(3+)/Yb(3+) NPs were demonstrated for their applications as a heterogeneous UC luminescence bioprobe to detect avidin with a detection limit of 180 pM. After bioconjugation with amino-terminal fragment (ATF) of urokinase plasminogen activator (uPA), NaScF4:Ln(3+) NPs also exhibited specific recognition of cancer cells overexpressed with uPA receptor (uPAR, an important marker of tumor biology and metastasis), showing great potentials in tumor-targeted bioimaging.

Reduction of the thermal conductivity of the thermoelectric material ScN by Nb alloying

DEFF Research Database (Denmark)

Tureson, Nina; Van Nong, Ngo; Fournier, Daniele

2017-01-01

) orientation. The crystal structure, morphology, thermal conductivity, and thermoelectric and electrical properties were investigated. The ScN reference film exhibited a Seebeck coefficient of −45 μV/K and a power factor of 6 × 10−4 W/m K2 at 750 K. Estimated from room temperature Hall measurements, all...... samples exhibit a high carrier density of the order of 1021 cm−3. Inclusion of heavy transition metals into ScN enables the reduction in thermal conductivity by an increase in phonon scattering. The Nb inserted ScN thin films exhibited a thermal conductivity lower than the value of the ScN reference (10.......5 W m−1 K−1) down to a minimum value of 2.2 Wm−1 K−1. Insertion of Nb into ScN thus resulted in a reduction in thermal conductivity by a factor of ∼5 due to the mass contrast in ScN, which increases the phonon scattering in the material....

Optimizing complex scandium-3,3 benzilidene BIS [4-hydroxycoumarin] with 46Sc radiotracer

International Nuclear Information System (INIS)

Khanza Aktari Dewi; Muhamad Basit Febrian; Duyeh Setiawan

2015-01-01

Coumarin, coumarin derivatives and coumarin complex compounds known to possess biological activities such as anticancer and antiviral. The reaction between the active compound coumarin derivatives with radioisotopes Sc-46 is expected to give a complex that will be marked for further investigation of its biological activity in purpose of drug development based on coumarin. This study aims to determine the optimum conditions in the synthesis of its complex compounds as well as the physico chemical characteristics including physical properties and radiochemical purity of the complex. 3.3 benzilidene bis [4-hydroxycoumarin] ligand has successfully synthesized by reacting 4-hydroxycoumarin with benzaldehyde. Complex solids formed instantly when the solution ScCl 3 labeled by Sc-46 with a pH of 5 is reacted with a ligand solution with a pH of 11 with the optimum ratio of Sc: ligand were 1:2 with optimum labeling percentage of 99,75 ± 0,02%. FTIR analysis of complex compounds and ligands show some shift in absorption due to the formation of complex. Melting point of ligand was 234°C whilst complex compound was not yet melted in maximum range of Fischer-Jons instrument at 300°C. The complex was white reddish coloured and well soluble in DMSO. Radiochemical purity of the complex Sc-(3,3 benzilidene bis [4-hydroxycoumarin]) 2 .2H 2 O was 91.22%. Complex compound of coumarin labeled by Sc-46 has been successfully synthesized and characterized with proposed molecular formula of Sc-(3,3 benzilidene bis [4-hydroxycoumarin]) 2 .2H 2 O. (author)

High Reflectance Nanoscale V/Sc Multilayer for Soft X-ray Water Window Region.

Science.gov (United States)

Huang, Qiushi; Yi, Qiang; Cao, Zhaodong; Qi, Runze; Loch, Rolf A; Jonnard, Philippe; Wu, Meiyi; Giglia, Angelo; Li, Wenbin; Louis, Eric; Bijkerk, Fred; Zhang, Zhong; Wang, Zhanshan

2017-10-10

V/Sc multilayer is experimentally demonstrated for the first time as a high reflectance mirror for the soft X-ray water window region. It primarily works at above the Sc-L edge (λ = 3.11 nm) under near normal incidence while a second peak appears at above the V-L edge (λ = 2.42 nm) under grazing incidence. The V/Sc multilayer fabricated with a d-spacing of 1.59 nm and 30 bilayers has a smaller interface width (σ = 0.27 and 0.32 nm) than the conventional used Cr/Sc (σ = 0.28 and 0.47 nm). For V/Sc multilayer with 30 bilayers, the introduction of B 4 C barrier layers has little improvement on the interface structure. As the number of bilayers increasing to 400, the growth morphology and microstructure of the V/Sc layers evolves with slightly increased crystallization. Nevertheless, the surface roughness remains to be 0.25 nm. A maximum soft X-ray reflectance of 18.4% is measured at λ = 3.129 nm at 9° off-normal incidence using the 400-bilayers V/Sc multilayer. According to the fitted model, an s-polarization reflectance of 5.2% can also be expected at λ = 2.425 nm under 40° incidence. Based on the promising experimental results, further improvement of the reflectance can be achieved by using a more stable deposition system, exploring different interface engineering methods and so on.

An Original Transformer and Switched-Capacitor (T & SC-Based Extension for DC-DC Boost Converter for High-Voltage/Low-Current Renewable Energy Applications: Hardware Implementation of a New T & SC Boost Converter

Directory of Open Access Journals (Sweden)

Sanjeevikumar Padmanaban

2018-03-01

Full Text Available In this article a new Transformer and Switched Capacitor-based Boost Converter (T & SC-BC is proposed for high-voltage/low-current renewable energy applications. The proposed T & SC-BC is an original extension for DC-DC boost converter which is designed by utilizing a transformer and switched capacitor (T & SC. Photovoltaic (PV energy is a fast emergent segment among the renewable energy systems. The proposed T & SC-BC combines the features of the conventional boost converter and T & SC to achieve a high voltage conversion ratio. A Maximum Power Point Tracking (MPPT controller is compulsory and necessary in a PV system to extract maximum power. Thus, a photovoltaic MPPT control mechanism also articulated for the proposed T & SC-BC. The voltage conversion ratio (Vo/Vin of proposed converter is (1 + k/(1 − D where, k is the turns ratio of the transformer and D is the duty cycle (thus, the converter provides 9.26, 13.88, 50/3 voltage conversion ratios at 78.4 duty cycle with k = 1, 2, 2.6, respectively. The conspicuous features of proposed T & SC-BC are: (i a high voltage conversion ratio (Vo/Vin; (ii continuous input current (Iin; (iii single switch topology; (iv single input source; (v low drain to source voltage (VDS rating of control switch; (vi a single inductor and a single untapped transformer are used. Moreover, the proposed T & SC-BC topology was compared with recently addressed DC-DC converters in terms of number of components, cost, voltage conversion ratio, ripples, efficiency and power range. Simulation and experimental results are provided which validate the functionality, design and concept of the proposed approach.

Ferromagnetism carried by highly delocalized hybrid states in Sc-doped ZnO thin films

KAUST Repository

Benali Kanoun, Mohammed

2012-05-29

We present first-principles results for Sc-doped ZnOthin films. Neighboring Sc atoms in the surface and/or subsurface layers are found to be coupled ferromagnetically, where only two of the possible configurations induce spin polarization. In the first configuration, the polarization is carried by the Sc d states as expected for transition metaldoping. However, there is a second configuration which is energetically favorable. It is governed by polarized hybrid states of the Zns, O p, and Sc d orbitals. Such highly delocalized states can be an important ingredient for understanding the magnetism of dopedZnOthin films.

Acute oral safety study of sodium caseinate glycosylated via maillard reaction with galactose in rats.

Science.gov (United States)

Anadón, Arturo; Martínez, Maria A; Ares, Irma; Castellano, Victor; Martínez-Larrañaga, Maria R; Corzo-Martínez, Marta; Moreno, F Javier; Villamiel, Mar

2014-03-01

In order to potentially use sodium caseinate (SC) glycated with galactose (Gal) in the food industry as a new functional ingredient with proved technological and biological properties, an evaluation of oral acute toxicity has been carried out. An acute safety study with SC-Gal glycoconjugates in the Wistar rat with a single oral gavage dose of 2,000 mg/kg of body weight was conducted. The SC-Gal glycoconjugates were well tolerated; no adverse effects or mortality was observed during the 2-week observation period. No abnormal signs, behavioral changes, body weight changes, or alterations in food and water consumption occurred. After this period, no changes in hematological and serum chemistry parameters, organ weights, or gross pathology or histopathology were detected. It was concluded that SC-Gal glycoconjugates obtained via the Maillard reaction were well tolerated in rats at an acute oral dose of 2,000 mg/kg of body weight. The SC-Gal glycoconjugates have a low order of acute toxicity, and the oral 50 % lethal dose for male and female rats is in excess of 2,000 mg/kg of body weight.

Update on the NSF PAARE Program at SC State

Science.gov (United States)

Walter, Donald K.; Ajello, Marco; Brittain, Sean D.; Cash, Jennifer; Hartmann, Dieter; Ho, Shirley; Howell, Steve B.; King, Jeremy R.; Leising, Mark D.; Smith, Daniel M.

2017-01-01

We report on results from our NSF PAARE program during Year 2 of the project. Our partnership under this PAARE award includes South Carolina State University (a Historically Black College/University), Clemson University (a Ph.D. granting institution) as well as individual investigators at NASA Ames and Carnegie Mellon University. Our recent work on variable and peculiar stars, work with the Kepler Observatory and our educational products in cosmology for non-STEM majors will be presented. We have successfully piloted sharing our teaching resources by offering an upper-level astrophysics course taught at Clemson via video conferencing , allowing a graduating senior from SC State to take a course not available through his home institution. Additionally, we are working on a memorandum of agreement between the two institutions that will allow for the seamless transfer of an undergraduate from SC State to Clemson’s graduate program in physics and astronomy. Our curriculum work includes new web-based cosmology activities and laboratory experiments. SC State undergraduates are reporting at this conference on their work with the light curves of semiregular variables using Kepler data. Additionally, we are heavily involved in the Citizen CATE Experiment. A PAARE scholarship student from SC State and the PAARE PI traveled to Indonesia for the March 2016 solar eclipse. Their results are also being presented elsewhere at this conference (see Myles McKay’s poster). Support for this work includes our NSF PAARE award AST-1358913 as well as resources and support provided by Clemson University and the National Optical Astronomy Observatory. Additional support has been provided by the South Carolina Space Grant Consortium and from NASA to SC State under awards NNX11AB82G and NNX13AC24G. CATE work has been supported by NASA SMD award NNX16AB92A to the National Solar Observatory. Additional details can be found at: http://physics.scsu.edu

Isospin excitation of nucleus in 42,44,48Ca (p,n)42,44,48Sc

International Nuclear Information System (INIS)

Suzuki, Keiji

2002-01-01

To obtain information of (p,n) reaction of heavy nucleus in 100 MeV or less, 42,44,48 Ca(p,n) 42,44,48 Sc was observed on the Cyclotron Radio Isotope Center in Tohoku University. The experimental results showed that 7, 8 and 10 spin parities were determined for 42 Sc, 44 Sc and 48 SC, respectively. It was the first determination of one and two negative parity transition of 42 Sc and 48 Sc,respectively, by (p,n) reaction. The full space wave function made by 0f1p shell effective interaction by Richter,et al is good accuracy and reliability. On the (p,n) reaction at E p =35 MeV, the transition matrix elements of 42 Ca, 44 Ca and 48 Ca were derived. On the experiment of 42 Ca(p,n) 42 Sc at E p 2 on energy was agreed with the calculation results by Franey and Love. The nuclear structure of 42 Ca was thought to show more stronger U(4) symmetry, because strong GT transition at T=1 was not observed, which was expected by j-j bonding shell model calculation. (S.Y.)

Crystal, magnetic, calorimetric and electronic structure investigation of GdScGe1-x Sb x compounds

Science.gov (United States)

Guillou, F.; Pathak, A. K.; Hackett, T. A.; Paudyal, D.; Mudryk, Y.; Pecharsky, V. K.

2017-12-01

Experimental investigations of crystal structure, magnetism and heat capacity of compounds in the pseudoternary GdScGe-GdScSb system combined with density functional theory projections have been employed to clarify the interplay between the crystal structure and magnetism in this series of RTX materials (R  =  rare-earth, T   =  transition metal and X  =  p-block element). We demonstrate that the CeScSi-type structure adopted by GdScGe and CeFeSi-type structure adopted by GdScSb coexist over a limited range of compositions 0.65 ≤slant x ≤slant 0.9 . Antimony for Ge substitutions in GdScGe result in an anisotropic expansion of the unit cell of the parent that is most pronounced along the c axis. We believe that such expansion acts as the driving force for the instability of the double layer CeScSi-type structure of the parent germanide. Extensive, yet limited Sb substitutions 0 ≤slant x disappearance of the induced magnetic moments on Sc. For the parent antimonide, heat capacity measurements indicate an additional transition below the main antiferromagnetic transition.

Fast conversion of scFv to Fab antibodies using type IIs restriction enzymes.

Science.gov (United States)

Sanmark, Hanna; Huovinen, Tuomas; Matikka, Tero; Pettersson, Tiina; Lahti, Maria; Lamminmäki, Urpo

2015-11-01

Single chain variable fragment (scFv) antibody libraries are widely used for developing novel bioaffinity reagents, although Fab or IgG molecules are the preferred antibody formats in many final applications. Therefore, rapid conversion methods for combining multiple DNA fragments are needed to attach constant domains to the scFv derived variable domains. In this study we describe a fast and easy cloning method for the conversion of single framework scFv fragments to Fab fragments using type IIS restriction enzymes. All cloning steps excluding plating of the Fab transformants can be done in 96 well plates and the procedure can be completed in one working day. The concept was tested by converting 69 scFv clones into Fab format on 96 well plates, which resulted in 93% success rate. The method is particularly useful as a high-throughput tool for the conversion of the chosen scFv clones into Fab molecules in order to analyze them as early as possible, as the conversion can significantly affect the binding properties of the chosen clones. Copyright © 2015 Elsevier B.V. All rights reserved.

Nuclear power plant systems, structures and components and their safety classification

International Nuclear Information System (INIS)

2000-01-01

The assurance of a nuclear power plant's safety is based on the reliable functioning of the plant as well as on its appropriate maintenance and operation. To ensure the reliability of operation, special attention shall be paid to the design, manufacturing, commissioning and operation of the plant and its components. To control these functions the nuclear power plant is divided into structural and functional entities, i.e. systems. A systems safety class is determined by its safety significance. Safety class specifies the procedures to be employed in plant design, construction, monitoring and operation. The classification document contains all documentation related to the classification of the nuclear power plant. The principles of safety classification and the procedures pertaining to the classification document are presented in this guide. In the Appendix of the guide, examples of systems most typical of each safety class are given to clarify the safety classification principles

β decay and isomeric properties of neutron-rich Ca and Sc isotopes

International Nuclear Information System (INIS)

Crawford, H. L.; Mantica, P. F.; Berryman, J. S.; Stoker, J. B.; Janssens, R. V. F.; Carpenter, M. P.; Kay, B. P.; Lauritsen, T.; Zhu, S.; Broda, R.; Cieplicka, N.; Fornal, B.; Grinyer, G. F.; Minamisono, K.; Hoteling, N.; Stefanescu, I.; Walters, W. B.

2010-01-01

The isomeric and β-decay properties of neutron-rich 53-57 Sc and 53,54 Ca nuclei near neutron number N=32 are reported, and the low-energy level schemes of 53,54,56 Sc and 53-57 Ti are presented. The low-energy level structures of the 21 Sc isotopes are discussed in terms of the coupling of the valence 1f 7/2 proton to states in the corresponding 20 Ca cores. Implications with respect to the robustness of the N=32 subshell closure are discussed, as well as the repercussions for a possible N=34 subshell closure.

Investigating the local structure of B-site cations in (1-x)BaTiO3-xBiScO3 and (1-x)PbTiO3-xBiScO3 using X-ray absorption spectroscopy

Science.gov (United States)

Blanchard, Peter E. R.; Grosvenor, Andrew P.

2018-05-01

The structural properties of (1-x)BaTiO3-xBiScO3 and (1-x)PbTiO3-xBiScO3 were investigated using powder X-ray diffraction and X-ray absorption spectroscopy. Diffraction measurements confirmed that substituting small amounts of BiScO3 into BaTiO3 initially stabilizes a cubic phase at x = 0.2 before impurity phases begin to form at x = 0.5. BiScO3 substitution also resulted in noticeable changes in the local coordination environment of Ti4+. X-ray absorption near-edge spectroscopy (XANES) analysis showed that replacing Ti4+ with Sc3+ results in an increase in the off-centre displacement of Ti4+ cations. Surprisingly, BiScO3 substitution has no effect on the displacement of the Ti4+ cation in the (1-x)PbTiO3-xBiScO3 solid solution.

Roberts-SC phocomelia syndrome.

Science.gov (United States)

Maheshwari, A; Kumar, P; Dutta, S; Narang, A

2001-06-01

A severely growth retarded baby was born at 38 weeks gestation. He had multiple craniofacial anomalies, microbrachycephaly, phocomelia in the upper limbs and renal cysts visible on ultrasound. He died of recurrent apneas. The autopsy showed left sided multicystic dysplastic kidney and absence of one testis. Cytogenetic studies did not reveal any abnormality. The phenotypic features match those described in the Roberts-SC phocomelia syndrome. A literature review revealed that 50% of these patients have chromosomal defects and antenatal detection is possible on ultrasound and by chromosome analysis of the amniocytes.

Safety code 19: recommended safety procedures for the selection, installation and use of x-ray diffraction equipment

International Nuclear Information System (INIS)

1984-01-01

This document is one of a series of Safety Codes prepared by the Radiation Protection Bureau to set out requirements for the safe use of radiation emitting devices. The equipment and installation guidelines and safety procedures detailed in this Code are primarily for the instruction and guidance of persons employed in Federal Public Service Departments and Agencies, as well as those coming under the jurisdiction of the Canada Labour Code. This Safety Code is also intended to assist other users of X-ray diffraction equipment to select safe equipment and to install and use it so that the radiation hazard to the operator and other persons in its vicinity is negligible. It should be noted that facilities under provincial jurisdiction may be subject to requirements specified under provincial statutes. This Code supersedes Safety Code RPD-SC-7, entitled 'Requirements For Non-Medical X-Ray Equipment, Use and Installation', insofar as X-ray diffraction equipment is concerned, and it is intended to complement X-ray equipment design, construction and performance standards promulgated under the Radiation Emitting Devices Act

Timescale differences between SC-PDSI and SPEI for drought monitoring in China

Science.gov (United States)

Zhao, Haiyan; Gao, Ge; An, Wei; Zou, Xukai; Li, Haitao; Hou, Meiting

2017-12-01

The Palmer Drought Severity Index (PDSI) has been widely used to monitor drought. Its characteristics are more suitable for measuring droughts of longer timescales, and this fact has not received much attention. The Standardized Precipitation Evapotranspiration Index (SPEI) can better reflect the climatic water balance, owing to its combination of precipitation and potential evapotranspiration. In this study, we selected monthly average air temperature and precipitation data from 589 meteorological stations of China's National Meteorological Information Center, to compare the effects of applying a self-calibrating PDSI (SC-PDSI) and SPEI to monitor drought events in the station regions, with a special focus on differences of event timescale. The results show the following. 1) Comparative analysis using SC-PDSI and SPEI for drought years and characters of three dry periods from 1961 to 2011 in the Beijing region showed that durations of SC-PDSI-based dry spells were longer than those of 3-month and 6-month SPEIs, but equal to those of 12-month or longer timescale SPEIs. 2) For monitoring evolution of the fall 2009 to spring 2010 Southwest China drought and spring 2000 Huang-Huai drought, 3-month SPEI could better monitor the initiation, aggravation, alleviation and relief of drought in the two regions, whereas the SC-PDSI was insensitive to drought recovery because of its long-term memory of previous climate conditions. 3) Analysis of the relationship between SC-PDSI for different regions and SPEI for different timescales showed that correlation of the two indexes changed with region, and SC-PDSI was maximally correlated with SPEI of 9-19 months in China. Therefore, SC-PDSI is only suitable for monitoring mid- and long-term droughts, owing to the strong lagged autocorrelation such as 0.4786 for 12-month lagged ones in Beijing, whereas SPEI is suitable for both short- and long-term drought-monitoring and should have greater application prospects in China.

Cytogenetic diagnosis of Roberts SC phocomelia syndrome: First ...

African Journals Online (AJOL)

Tahir M. Malla

2015-07-14

/licenses/by-nc-nd/4.0/). 1. Introduction. Roberts SC phocomelia syndrome is an autosomal recessive developmental disorder characterized by pre and postnatal growth retardation, microcephaly, craniofacial anomalies,.

Safety classification of nuclear power plant systems, structures and components

International Nuclear Information System (INIS)

1992-01-01

The Safety Classification principles used for the systems, structures and components of a nuclear power plant are detailed in the guide. For classification, the nuclear power plant is divided into structural and operational units called systems. Every structure and component under control is included into some system. The Safety Classes are 1, 2 and 3 and the Class EYT (non-nuclear). Instructions how to assign each system, structure and component to an appropriate safety class are given in the guide. The guide applies to new nuclear power plants and to the safety classification of systems, structures and components designed for the refitting of old nuclear power plants. The classification principles and procedures applying to the classification document are also given

IGSC Experience: Links Between RD and D and Stakeholder Confidence: The Aspect of Long-Term Safety

International Nuclear Information System (INIS)

Stroemberg, Bo

2008-01-01

Bo Stroemberg from the IGSC Core Group (SKI, Sweden) reported on the International Symposium on the Safety Case organised in 2007 by IGSC. Participants of a session focusing on the role of the safety case in societal dialogue pointed out that in the technical community there is a shared understanding of the issues of long-term safety, which the SC should address. They observed, however, that public concerns may be quite different from these issues. For example, the extremely long timescales are not easily understood by the broader public. Also, technical experts' focus on quantitative indicators is incompatible with the perceptions of non-experts, who tend to give heavier weight to qualitative characteristics of risks. Therefore, conducting a dialogue with the public in which their safety concerns are explored is of key importance. It is not only the technical content but also the presentation of the SC which should be adapted to stakeholders' concerns. At the same time, stakeholder input can improve both the technical basis and the presentation of the SC. Mr Stroemberg went on to present IGSC Core Group answers to questions addressed to them by the FSC: 1. What are the questions about safety and the safety case you feel the public is asking? What kind of reply? Or approach to replying? Do they require? What weight should they be given? 2. How has dialogue with stakeholders improved your safety case? What lessons may be drawn for the technical community to improve on its capability to respond to questions from the general public and other stakeholders? 3. What is the role of RD and D when arguing safety or confidence in safety? Anecdotal experience was received from Europe, Japan and the United States. Common concerns expressed by the public focus on how scientists can 'know they are right' when making safety predictions for the long term, and whether unexpected events can be addressed. Because some concerns fall beyond the topics typically covered by a safety case

Laser Safety Inspection Criteria

International Nuclear Information System (INIS)

Barat, K

2005-01-01

A responsibility of the Laser Safety Officer (LSO) is to perform laser safety audits. The American National Standard Z136.1 Safe use of Lasers references this requirement in several sections: (1) Section 1.3.2 LSO Specific Responsibilities states under Hazard Evaluation, ''The LSO shall be responsible for hazards evaluation of laser work areas''; (2) Section 1.3.2.8, Safety Features Audits, ''The LSO shall ensure that the safety features of the laser installation facilities and laser equipment are audited periodically to assure proper operation''; and (3) Appendix D, under Survey and Inspections, it states, ''the LSO will survey by inspection, as considered necessary, all areas where laser equipment is used''. Therefore, for facilities using Class 3B and or Class 4 lasers, audits for laser safety compliance are expected to be conducted. The composition, frequency and rigueur of that inspection/audit rests in the hands of the LSO. A common practice for institutions is to develop laser audit checklists or survey forms. In many institutions, a sole Laser Safety Officer (LSO) or a number of Deputy LSO's perform these audits. For that matter, there are institutions that request users to perform a self-assessment audit. Many items on the common audit list and the associated findings are subjective because they are based on the experience and interest of the LSO or auditor in particular items on the checklist. Beam block usage is an example; to one set of eyes a particular arrangement might be completely adequate, while to another the installation may be inadequate. In order to provide more consistency, the National Ignition Facility Directorate at Lawrence Livermore National Laboratory (NIF-LLNL) has established criteria for a number of items found on the typical laser safety audit form. These criteria are distributed to laser users, and they serve two broad purposes: first, it gives the user an expectation of what will be reviewed by an auditor, and second, it is an

Intracellular scFvs against the viral E6 oncoprotein provoke apoptosis in human papillomavirus-positive cancer cells

International Nuclear Information System (INIS)

Lagrange, Magali; Boulade-Ladame, Charlotte; Mailly, Laurent; Weiss, Etienne; Orfanoudakis, Georges; Deryckere, Francois

2007-01-01

The E6 protein of human papillomavirus type 16 (16E6) is involved in the tumorigenesis of human cervical cells by targeting numerous cellular proteins. We have designed a strategy for neutralizing 16E6 based on the intracellular expression of single-chain Fv antibodies (scFvs) specific to 16E6. Recombinant adenovirus vectors were constructed to allow expression of two 16E6-binding scFvs and one 16E6-non-binding scFv in HPV16-positive and -negative cells. Expression of the scFvs provoked two types of effects: (i) inhibition of proliferation of all cell lines tested, this aspecific toxicity being likely due to the aggregation of unfolded scFvs; and (ii) apoptosis observed only in HPV16-positive cervical cancer cell lines after expression of 16E6-binding scFvs, this specific effect being proportional to the intracellular solubility of the scFvs. These data demonstrate the feasibility of intracellular immunization with anti-16E6 scFvs and highlight the importance of the solubility of the intracellular antibodies

Preliminary safety evaluation (PSE) for Sodium Storage Facility at the Fast Flux Test Facility

International Nuclear Information System (INIS)

Bowman, B.R.

1994-01-01

This evaluation was performed for the Sodium Storage Facility (SSF) which will be constructed at the Fast Flux Test Facility (FFTF) in the area adjacent to the South and West Dump Heat Exchanger (DHX) pits. The purpose of the facility is to allow unloading the sodium from the FFTF plant tanks and piping. The significant conclusion of this Preliminary Safety Evaluation (PSE) is that the only Safety Class 2 components are the four sodium storage tanks and their foundations. The building, because of its imminent risk to the tanks under an earthquake or high winds, will be Safety Class 3/2, which means the building has a Safety Class 3 function with the Safety Class 2 loads of seismic and wind factored into the design

Synthesis and crystal structure of the first Sc-Nb-O-N phases

Energy Technology Data Exchange (ETDEWEB)

Orthmann, Steven; Lerch, Martin [Institut fuer Chemie, Technische Universitaet Berlin (Germany)

2017-11-17

Synthesis of phase-pure materials in the system Sc-Nb-O-N is challenging. In this contribution we report on the preparation of the first scandium niobium oxide nitrides via reaction of water-saturated gaseous ammonia or an ammonia-oxygen mixture with amorphous scandium niobium oxides. Two new phases were obtained: rutile-type ScNb{sub 4}O{sub 7}N{sub 3}, which crystallizes in space group P4{sub 2}/mnm, and an anion-deficient fluorite-type Sc{sub 2}Nb(O,N,⬜){sub 6} phase crystallizing in space group Fm anti 3m. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Magnet measuring equipment of SC2

CERN Multimedia

1974-01-01

Checking the positioning of the magnet measuring equipment installed between the poles of SC2. The steel structure in front of the magnet is designed to house the rotary condenser and to shield it from the stray magnetic field of the accelerator. On the left, Marinus van Gulik. (See Photo Archive 7402005 and Annual Report 1974, p. 44.)

Measurement of the elastic tensor of SmScO3 and NdScO3 using resonant ultrasound spectroscopy with ab initio calculations

Directory of Open Access Journals (Sweden)

K. A. Pestka II

2011-09-01

Full Text Available The complete elastic tensors of SmScO3 and NdScO3 were measured using resonant ultrasound spectroscopy (RUS in combination with ab-initio calculations. Measurement of the elastic tensor of these recently synthesized single crystal RE scandates is essential for understanding dynamic lattice applications including phonon confinement, strain induced thin film growth and superlattice construction. On average, the experimental elastic constants differed by less than 5% of the theoretical values, further validating the accuracy of modern ab-initio calculations as a means of estimating the initial elastic constants used in RUS measurements.

A novel fusion protein of IP10-scFv retains antibody specificity and chemokine function

International Nuclear Information System (INIS)

Guo Junqing; Chen Liu; Ai Hongwu; Jing Jiannian; Zhou Jiyong; Zhang Chuyu; You Shangyou

2004-01-01

We combined the specificity of tumor-specific antibody with the chemokine function of interferon-γ inducible protein 10 (IP-10) to recruit immune effector cells in the vicinity of tumor cells. A novel fusion protein of IP10-scFv was constructed by fusing mouse IP-10 to V H region of single-chain Fv fragment (scFv) against acidic isoferritin (AIF), and expressed in NS0 murine myeloma cells. The IP10-scFv fusion protein was shown to maintain the specificity of the antiAIF scFv with similar affinity constant, and bind to the human hepatocarcinoma SMMC 7721 cells secreting AIF as well as the activated mouse T lymphocytes expressing CXCR3 receptor. Furthermore, the IP10-scFv protein either in solution or bound on the surface of SMMC 7721 cells induced significant chemotaxis of mouse T cells in vitro. The results indicate that the IP10-scFv fusion protein possesses both bioactivities of the tumor-specific antibody and IP-10 chemokine, suggesting its possibility to induce an enhanced immune response against the residual tumor cells in vivo

Conductivity ageing studies on 1M10ScSZ (M4+=Ce, Hf)

DEFF Research Database (Denmark)

Omar, Shobit; Bin Najib, Waqas; Bonanos, Nikolaos

2011-01-01

The long-term conductivity stability is tested on zirconia based electrolyte materials for solid oxide fuel cell applications. The ageing studies have been performed on the samples of ZrO2 co-doped with 10mol% of Sc2O3 and 1mol% MO2, where M = Ce or Hf (denoted respectively 1Ce10ScSZ and 1Hf10Sc......SZ) in oxidising and reducing atmospheres, at 600°C for 3000h. At 600°C, these compositions show initial conductivity of around 9–12mS∙cm−1 in air. After 3000h of ageing, no phase transitions are observed in any of the samples. For the first 1000h, the degradation rate is higher than in the subsequent 2000h......; thereafter, conductivity degrades linearly with time for all samples. In air, the loss in the conductivity is lower than in reducing conditions. The 1Ce10ScSZ shows the highest degradation rate of 3.8%/1000h in wet H2/N2 after the first 1000h of ageing. A colour change of the 1Ce10ScSZ sample from white...

SC-CO2-assisted process for a high energy density aerogel supercapacitor: the effect of GO loading

Science.gov (United States)

Sarno, Maria; Baldino, Lucia; Scudieri, Carmela; Cardea, Stefano; Ciambelli, Paolo; Reverchon, Ernesto

2017-05-01

Energy density, safety, and simple and environmentally friendly preparation methods are very significant aspects in the realization of a compact supercapacitor. Herein we report the use of a supercritical CO2-assisted gel drying process (SC-CO2) for the preparation of porous electrodes containing dispersed graphene in a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) binder membrane to sandwich in a new portable supercapacitor based on graphene oxide (GO). A GO loading of 60 wt.% was found to give the best combination of factors (porosity, wettability, mechanical and electrochemical properties). Cycling voltammetry and charge/discharge studies showed an excellent capacitance behaviour and stability in an ionic liquid electrolyte, suggesting SC-CO2 processing as a promising platform to produce highly bulky and porous films for supercapacitors. The supercapacitor device delivers a very high energy density of 79.2 Wh kg-1 at a power density of 0.23 KW kg-1 (current density 0.5 A g-1, specific capacitance 36.2 F g-1) while that of steel remains at 50.3 Wh kg-1 at a power density of 2.8 KW kg-1 (current density 6 A g-1, specific capacitance 23.5 F g-1).

Methodology for safety classification of PWR type nuclear power plants items

International Nuclear Information System (INIS)

Oliveira, Patricia Pagetti de

1995-01-01

This paper contains the criteria and methodology which define a classification system of structures, systems and components in safety classes according to their importance to nuclear safety. The use of this classification system will provide a set of basic safety requirements associated with each safety class specified. These requirements, when available and applicable, shall be utilized in the design, fabrication and installation of structures, systems and components of Pressurized Water Reactor Nuclear Power Plants. (author). 13 refs, 1 tab

Cytogenetic diagnosis of Roberts SC phocomelia syndrome: First report from Kashmir

Directory of Open Access Journals (Sweden)

Tahir M. Malla

2016-01-01

Full Text Available There are several syndromes in which specific mitotic chromosomal abnormalities can be seen, like premature centromere separation, premature (sister chromatid separation, and somatic aneuploidies. Identifications of such specific cytogenetic findings can be the key factor that leads towards the diagnosis of syndromes like Roberts SC phocomelia. The case presented here as Roberts SC phocomelia syndrome was identified as a child with multiple congenital anomalies and dysmorphic features. Conventional cytogenetic analysis of the case revealed premature sister chromatid separation. The premature centromeric separation was also confirmed by C banding analysis of the child. It is the first and the only case of Roberts SC phocomelia diagnosed from this part of the world. The present case report emphasizes the importance of conventional cytogenetics in the diagnosis of such syndromes.

Magnetic properties of Sc{sub x}Ti{sub 1-x}Fe{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Kessler, M. [Lab. de Cristallographie, CNRS, 38 - Grenoble (France); Deportes, J. [Lab. Louis Neel, CNRS, 38 - Grenoble (France); Ouladdiaf, B. [Institut Laue-Langevin, 38 - Grenoble (France); Sayetat, F. [Lab. de Cristallographie, CNRS, 38 - Grenoble (France)

1995-02-09

The magnetic properties and their thermal dependences of Sc{sub 0.1}Ti{sub 0.9}Fe{sub 1.96}, Sc{sub 0.1}Ti{sub 0.9}Fe{sub 2} and Sc{sub 0.1}Ti{sub 0.9}Fe{sub 2.04} are compared with those of TiFe{sub 2}. The substitution changes the iron-iron distances. Consequently, the Fe atoms on the 6h site show in addition to the antiferromagnetic component a small ferromagnetic one, and a weak magnetic moment appears on the 2a site. ((orig.)).

44Sc-DOTA-BN[2-14]NH2 in comparison to 68Ga-DOTA-BN[2-14]NH2 in pre-clinical investigation. Is 44Sc a potential radionuclide for PET?

Science.gov (United States)

Koumarianou, E; Loktionova, N S; Fellner, M; Roesch, F; Thews, O; Pawlak, D; Archimandritis, S C; Mikolajczak, R

2012-12-01

In the present study we demonstrate the in vitro and in vivo comparison of the (44)Sc and (68)Ga labeled DOTA-BN[2-14]NH(2). (44)Sc is a positron emitter with a half life of 3.92 h. Hence it could be used for PET imaging with ligands requiring longer observation time than in the case of (68)Ga. The binding affinity of (nat)Sc-DOTA-BN[2-14]NH(2) and (nat)Ga-DOTA-BN[2-14]NH(2) to GRP receptors was studied in competition to [(125)I-Tyr(4)]-Bombesin in the human prostate cancer cell line PC-3. A preliminary biodistribution in normal rats was performed, while first microPET images were assessed in male Copenhagen rats bearing the androgen-independent Dunning R-3327-AT-1 prostate cancer tumor. The affinity to GRP receptors in the PC-3 cell line was higher for (nat)Ga-DOTA-BN[2-14]NH(2) (IC(50)(nM)=0.85 ± 0.06) than that of (nat)Sc-DOTA-BN[2-14]NH(2) (IC(50) (nM)=6.49 ± 0.13). The internalization rate of (68)Ga labeled DOTA-BN[2-14]NH(2) was slower than that of (44)Sc, but their final internalization percents were comparable. (68)Ga-DOTA-BN[2-14]NH(2) was externalized faster than (44)Sc-DOTA-BN[2-14]NH(2). The biodistribution of (44)Sc-DOTA-BN[2-14]NH(2) and (68)Ga-DOTA-BN[2-14]NH(2) in normal rats revealed a higher uptake in target organs and tissues of the first one while both excreted mainly through urinary tract. In microPET images both tracers were accumulated in the tumor with similar uptake patterns. Despite the differences in the receptor affinity both the (68)Ga- and the (44)Sc-labeled DOTA-BN[2-14]NH(2) tracers showed comparable distribution and similar time constants of uptake and elimination. Moreover no differences in tumor accumulation (neither in the overall uptake nor in the dynamics) were observed from the microPet imaging. From that perspective the use of either (44)Sc or (68)Ga for detecting tumors with GRP receptors is equivalent. Copyright © 2012 Elsevier Ltd. All rights reserved.

Piezoelectric characterization of Sc0.26Al0.74N layers on Si (001) substrates

Science.gov (United States)

Sinusía Lozano, M.; Pérez-Campos, A.; Reusch, M.; Kirste, L.; Fuchs, Th; Žukauskaitė, A.; Chen, Z.; Iriarte, G. F.

2018-03-01

Scandium aluminum nitride (ScAlN) films have been synthesized by pulsed-DC reactive magnetron sputtering. The degree of c-axis orientation as well as piezoelectric characteristics of the Sc0.26Al0.74N thin films grown on Si (001) at various discharge powers and processing pressures values have been investigated. According to x-ray diffraction (XRD) measurements, the texture of the as-grown Sc0.26Al0.74N thin films becomes more prominent in the [0001]-direction at the highest target power (700 W) and at the lowest processing pressure (4 mTorr). The piezoelectric response, as determined by measuring the d33 piezoelectric constant, shows a maximum value of -12 pC/N also at 4 mTorr and 700 W, confirming a direct correlation between the d33 piezoelectric constant and the degree of orientation in the [0001]-direction. The atomic concentration of Sc and Al in the synthesized ScAlN thin film, determined by secondary ion mass spectroscopy (SIMS), reveals a Sc concentration lower than in the ScAl alloy target. The piezoresponse force microscopy (PFM) shows homogeneous polarity distribution with no inversion domains. The piezoelectric layers have been used to fabricate and measure surface acoustic wave (SAW) resonators on a Sc0.26Al0.74N/Si (001) bilayer system with resonance frequency of 1.4 GHz and coupling coefficient of 0.567. Such characteristic in the frequency response reveals the potential of these materials for advanced SAW devices in applications such as next generation (5 G) wireless communication systems.

Early Stages of Precipitation Process in Al-(Mn-)Sc-Zr Alloy Characterized by Positron Annihilation

KAUST Repository

Vlach, Martin; Cizek, Jakub; Melikhova, Oksana; Stulikova, Ivana; Smola, Bohumil; Kekule, Tomas; Kudrnova, Hana; Gemma, Ryota; Neubert, Volkmar

2015-01-01

Thermal effects on the precipitation stages in as-cast Al-0.70 at. pct Mn-0.15 at. pct Sc-0.05 at. pct Zr alloy were studied. The role of lattice defects was elucidated by positron annihilation spectroscopy (lifetime and coincidence Doppler broadening) enabling investigation of solutes clustering at the atomic scale. This technique has never been used in the Al-Sc- and/or Al-Zr-based alloys so far. Studies by positron annihilation were combined with resistometry, hardness measurements, and microstructure observations. Positrons trapped at defects are preferentially annihilated by Sc electrons. Lifetime of trapped positrons indicates that Sc atoms segregate at dislocations. Maximum fraction of positrons annihilated by Sc electrons occurring at 453 K (180 °C) suggests that clustering of Sc bound with vacancies takes place. It is followed by peak of this fraction at 573 K (300 °C). A rise of the contribution of trapped positrons annihilated by Zr electrons starting at 513 K (240 °C) and attaining maximum also at 573 K (300 °C) confirms that Zr participates in precipitation of the Al3Sc particles already at these temperatures. The pronounced hardening at 573 K (300 °C) has its nature in the precipitation of the Al3Sc particles with a Zr-rich shell. The contribution of trapped positrons annihilated by Mn electrons was found to be negligible. © 2015, The Minerals, Metals & Materials Society and ASM International.

Early Stages of Precipitation Process in Al-(Mn-)Sc-Zr Alloy Characterized by Positron Annihilation

KAUST Repository

Vlach, Martin

2015-01-29

Thermal effects on the precipitation stages in as-cast Al-0.70 at. pct Mn-0.15 at. pct Sc-0.05 at. pct Zr alloy were studied. The role of lattice defects was elucidated by positron annihilation spectroscopy (lifetime and coincidence Doppler broadening) enabling investigation of solutes clustering at the atomic scale. This technique has never been used in the Al-Sc- and/or Al-Zr-based alloys so far. Studies by positron annihilation were combined with resistometry, hardness measurements, and microstructure observations. Positrons trapped at defects are preferentially annihilated by Sc electrons. Lifetime of trapped positrons indicates that Sc atoms segregate at dislocations. Maximum fraction of positrons annihilated by Sc electrons occurring at 453 K (180 °C) suggests that clustering of Sc bound with vacancies takes place. It is followed by peak of this fraction at 573 K (300 °C). A rise of the contribution of trapped positrons annihilated by Zr electrons starting at 513 K (240 °C) and attaining maximum also at 573 K (300 °C) confirms that Zr participates in precipitation of the Al3Sc particles already at these temperatures. The pronounced hardening at 573 K (300 °C) has its nature in the precipitation of the Al3Sc particles with a Zr-rich shell. The contribution of trapped positrons annihilated by Mn electrons was found to be negligible. © 2015, The Minerals, Metals & Materials Society and ASM International.

Roberts-SC syndrome, a rare syndrome and cleft palate repair

Directory of Open Access Journals (Sweden)

Murthy Jyotsna

2008-01-01

Full Text Available Roberts SC syndrome is a rare syndrome with only 17 previously recognized patients reported in medical literature. The syndrome is characterized by multiple malformations, particularly, symmetrical limb reduction, craniofacial anomalies such as bilateral cleft lip and palate, micrognathia, and severe growth and mental retardation. Our patient, a young child of five years having Roberts-SC, was successfully operated for cleft palate under general anesthesia. The main features of the syndrome and the technical problems of anesthesia and surgery are discussed in this report.

CMS ECAL Endcap (EE) Dee Assembly - SC mounting on Dee 1

CERN Multimedia

Cockerill, D

2007-01-01

Protection panels on back of Dee 1, Completion of SC mounting, 03/10/2007: Completion of SC mounting (aart from the inner 3-2-1)on the first quadrant of Dee 1 and subsequent survey. 22-28/08/2007: The first supercrystals on Dee1, Dee1 in 867 with the first column of SCs ready for mounting, Dee1 with its protection panels over the laser monitoring fibre system

Cytogenetic diagnosis of Roberts SC phocomelia syndrome: First report from Kashmir

OpenAIRE

Tahir M. Malla; Arshad A. Pandith; Fayaz A. Dar; Mahrukh H. Zargar

2016-01-01

There are several syndromes in which specific mitotic chromosomal abnormalities can be seen, like premature centromere separation, premature (sister) chromatid separation, and somatic aneuploidies. Identifications of such specific cytogenetic findings can be the key factor that leads towards the diagnosis of syndromes like Roberts SC phocomelia. The case presented here as Roberts SC phocomelia syndrome was identified as a child with multiple congenital anomalies and dysmorphic features. Conve...

Thermal neutron capture and resonance integral cross sections of {sup 45}Sc

Energy Technology Data Exchange (ETDEWEB)

Van Do, Nguyen; Duc Khue, Pham; Tien Thanh, Kim [Institute of Physics, Vietnam Academy of Science and Technology, 10 Dao Tan, Hanoi (Viet Nam); Thi Hien, Nguyen [Institute of Physics, Vietnam Academy of Science and Technology, 10 Dao Tan, Hanoi (Viet Nam); Department of Physics and Center for High Energy Physics, Kyungpook National University, Daegu 702-701 (Korea, Republic of); Kim, Guinyun, E-mail: gnkim@knu.ac.kr [Department of Physics and Center for High Energy Physics, Kyungpook National University, Daegu 702-701 (Korea, Republic of); Kim, Kwangsoo [Department of Physics and Center for High Energy Physics, Kyungpook National University, Daegu 702-701 (Korea, Republic of); Shin, Sung-Gyun; Cho, Moo-Hyun [Department of Advanced Nuclear Engineering, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); Lee, Manwoo [Research Center, Dongnam Institute of Radiological and Medical Science, Busan 619-953 (Korea, Republic of)

2015-11-01

The thermal neutron cross section (σ{sub 0}) and resonance integral (I{sub 0}) of the {sup 45}Sc(n,γ){sup 46}Sc reaction have been measured relative to that of the {sup 197}Au(n,γ){sup 198}Au reaction by means of the activation method. High-purity natural scandium and gold foils without and with a cadmium cover of 0.5 mm thickness were irradiated with moderated pulsed neutrons produced from the Pohang Neutron Facility (PNF). The induced activities in the activated foils were measured with a high purity germanium (HPGe) detector. In order to improve the accuracy of the experimental results the counting losses caused by the thermal (G{sub th}) and resonance (G{sub epi}) neutron self-shielding, the γ-ray attenuation (F{sub g}) and the true γ-ray coincidence summing effects were made. In addition, the effect of non-ideal epithermal spectrum was also taken into account by determining the neutron spectrum shape factor (α). The thermal neutron cross-section and resonance integral of the {sup 45}Sc(n,γ){sup 46}Sc reaction have been determined relative to the reference values of the {sup 197}Au(n,γ){sup 198}Au reaction, with σ{sub o,Au} = 98.65 ± 0.09 barn and I{sub o,Au} = 1550 ± 28 barn. The present thermal neutron cross section has been determined to be σ{sub o,Sc} = 27.5 ± 0.8 barn. According to the definition of cadmium cut-off energy at 0.55 eV, the present resonance integral cross section has been determined to be I{sub o,Sc} = 12.4 ± 0.7 barn. The present results are compared with literature values and discussed.

Ionic conductivity of co-doped Sc2O3-ZrO2 ceramics

DEFF Research Database (Denmark)

Omar, Shobit; bin Najib, Waqas; Chen, Weiwu

2012-01-01

The oxide ionic conductivity of Sc0.18Zr0.82O1.91 doped with 0.5 mol.% of both Yb2O3 and In2O3 is evaluated at various temperatures in air. Among various co-doped compositions, In0.02Sc0.18Zr0.80O1.90 exhibits the highest grain ionic conductivity followed by Yb0.02Sc0.18Zr0.80O1.90 at 500°C....... However, it also possesses phase transformation from c- to β-phase at 475°C on cooling. In the present work, an attempt is made to completely stabilize the cphase in In0.02Sc0.18Zr0.80O1.90 by substituting 0.5 mol.% of In2O3 with Yb2O3, which can enhance the ionic conductivity in co-doped compositions....

Crystal structure of Na3Sc2(PO4)3 at 60 deg C

International Nuclear Information System (INIS)

Lazoryak, B.I.; Kalinin, V.B.; Stefanovich, S.Yu.; Efremov, V.A.

1980-01-01

The structure of the ferroelectric phase of Na 3 Sc 2 (PO 4 ) 3 compound was studied. Na 3 Sc 2 (PO 4 ) 3 monocrystal heated by a jet of warm N 2 was investigated at 60 deg C. The rhombohedron modification was determined: a=8.927(3), c=22.34(4) A, Z=6, space group R anti 3c. Interatomic distances and inner angles of polyhedrons in Na 3 Sc 2 (PO 4 ) 3 structure were determined

Self-assembling complexes of quantum dots and scFv antibodies for cancer cell targeting and imaging.

Directory of Open Access Journals (Sweden)

Tatiana A Zdobnova

Full Text Available Semiconductor quantum dots represent a novel class of fluorophores with unique physical and chemical properties which could enable a remarkable broadening of the current applications of fluorescent imaging and optical diagnostics. Complexes of quantum dots and antibodies are promising visualising agents for fluorescent detection of selective biomarkers overexpressed in tumor tissues. Here we describe the construction of self-assembling fluorescent complexes of quantum dots and anti-HER1 or anti-HER2/neu scFv antibodies and their interactions with cultured tumor cells. A binding strategy based on a very specific non-covalent interaction between two proteins, barnase and barstar, was used to connect quantum dots and the targeting antibodies. Such a strategy allows combining the targeting and visualization functions simply by varying the corresponding modules of the fluorescent complex.

Reaction of intermetallic compounds of the ScT composition (T=Ag, Cu, Zn, Ni) with hydrogen

International Nuclear Information System (INIS)

Shilkin, S.P.; Volkova, L.S.; Tarasov, B.P.

1995-01-01

Reaction of intermetallic compounds of ScT composition (T=Ag, Cu, Zn, Ni), crystallized in CsCl structural type, with hydrogen at 0.2-10 MPa pressure and 293-673 K temperature is studied by chemical, x-ray phase and complex thermogravimetry analysis methods. It is shown that under such conditions hydrogen absorption by ScAg and ScCu is accompanied by the decay of their source matrices into scandium dihydride and metal silver and copper respectively. For ScZn a fine-dispersion mixture of scandium dihydride with zinc and hydride phase of a new zinc-containing intermetallic compound appears to be the finite reaction product. In case of ScNi a hydride phase of ScNiH 2.6 composition is produced, which is crystallized in a rhombic syngony with the lattice periods: a=0.5281±0.0007, b=0.7393±0.0009 and c=0.3327±0.0004 nm. 9 refs.; 2 tabs

The Synchrocyclotron (SC) in building 300

CERN Multimedia

Maximilien Brice

2012-01-01

The red magnet of CERN's first accelerator, the Synchrocyclotron (SC), has occupied a large part of Hall 300 since it was installed in the late 1950s. The remaining part of the 300-square-metre building has been used as a storage room since the accelerator was shut down in 1990. Now a public exhibition will breathe new life into the hall.

In the presence of fluoride, free Sc³⁺ is not a good predictor of Sc bioaccumulation by two unicellular algae: possible role of fluoro-complexes.

Science.gov (United States)

Crémazy, Anne; Campbell, Peter G C; Fortin, Claude

2014-08-19

We investigated the effect of fluoride complexation on scandium accumulation by two unicellular algae, Chlamydomonas reinhardtii and Pseudokirchneriella subcapitata. This trivalent metal was selected for its chemical similarities with aluminum and for its convenient radioisotope (Sc-46), which can be used as a tracer in short-term bioaccumulation studies. Scandium surface-bound concentrations (Sc(ads)) and uptake fluxes (J(int)) were estimated in the two algae over short-term (organisms.

44Sc for labeling of DOTA- and NODAGA-functionalized peptides: preclinical in vitro and in vivo investigations.

Science.gov (United States)

Domnanich, Katharina A; Müller, Cristina; Farkas, Renata; Schmid, Raffaella M; Ponsard, Bernard; Schibli, Roger; Türler, Andreas; van der Meulen, Nicholas P

2017-01-01

Recently, 44 Sc (T 1/2  = 3.97 h, Eβ + av  = 632 keV, I = 94.3 %) has emerged as an attractive radiometal candidate for PET imaging using DOTA-functionalized biomolecules. The aim of this study was to investigate the potential of using NODAGA for the coordination of 44 Sc. Two pairs of DOTA/NODAGA-derivatized peptides were investigated in vitro and in vivo and the results obtained with 44 Sc compared with its 68 Ga-labeled counterparts.DOTA-RGD and NODAGA-RGD, as well as DOTA-NOC and NODAGA-NOC, were labeled with 44 Sc and 68 Ga, respectively. The radiopeptides were investigated with regard to their stability in buffer solution and under metal challenge conditions using Fe 3+ and Cu 2+ . Time-dependent biodistribution studies and PET/CT imaging were performed in U87MG and AR42J tumor-bearing mice. Both RGD- and NOC-based peptides with a DOTA chelator were readily labeled with 44 Sc and 68 Ga, respectively, and remained stable over at least 4 half-lives of the corresponding radionuclide. In contrast, the labeling of NODAGA-functionalized peptides with 44 Sc was more challenging and the resulting radiopeptides were clearly less stable than the DOTA-derivatized matches. 44 Sc-NODAGA peptides were clearly more susceptible to metal challenge than 44 Sc-DOTA peptides under the same conditions. Instability of 68 Ga-labeled peptides was only observed if they were coordinated with a DOTA in the presence of excess Cu 2+ . Biodistribution data of the 44 Sc-labeled peptides were largely comparable with the data obtained with the 68 Ga-labeled counterparts. It was only in the liver tissue that the uptake of 68 Ga-labeled DOTA compounds was markedly higher than for the 44 Sc-labeled version and this was also visible on PET/CT images. The 44 Sc-labeled NODAGA-peptides showed a similar tissue distribution to those of the DOTA peptides without any obvious signs of in vivo instability. Although DOTA revealed to be the preferred chelator for stable coordination of 44

Fermilab's SC Accelerator Magnet Program for Future U.S. HEP Facilities

International Nuclear Information System (INIS)

Lamm, Michael; Zlobin, Alexander

2010-01-01

The invention of SC accelerator magnets in the 1970s opened wide the possibilities for advancing the energy frontier of particle accelerators, while limiting the machine circumference and reducing their energy consumption. The successful development of SC accelerator magnets based on NbTi superconductor have made possible a proton-antiproton collider (Tevatron) at Fermilab, an electron-proton collider (HERA) at DESY, a relativistic heavy ion collider (RHIC) at BNL and recently a proton-proton collider (LHC) at CERN. Further technological innovations and inventions are required as the US HEP looks forward towards the post-LHC energy or/and intensity frontiers. A strong, goal oriented national SC accelerator magnet program must take on this challenge to provide a strong base for the future of HEP in the U.S. The results and experience obtained by Fermilab during the past 30 years will allow us to play a leadership role in the SC accelerator magnet development in the U.S., in particular, focusing on magnets for a Muon Collider/Neutrino Factory (1)-(2). In this paper, we summarize the required Muon Collider magnet needs and challenges, summarize the technology advances in the Fermilab accelerator magnet development over the past few years, and present and discuss our vision and long-term plans for these Fermilab-supported accelerator initiatives.

Spectrophotometric determination of Sc in eriochrome cyanine R(chrome azurol S) - phosphatidyl choline system

International Nuclear Information System (INIS)

Xu, Y.; Chen, X.; Hu, Z.

1987-01-01

Eriochrome cyanine R(chrome azurol S) is used as a color reagent to determine Sc in the presence of phosphatidyl choline, eta = 3.7 * 10 4 (4.5 * 10 4 ). This method has been connected to extraction separation to determine Sc in the presence of rare earth elements, and good results have been obtained. Phosphatidyl choline(PC) is a biochemical reagent, which can be used as a surfactant. It has been reported that chrome azurol S(CAS) can be used to determine Be in the presence of PC but it has not been reported that eriochrome cyanine R(ECR) and CAS can been used to determine Sc in the presence of PC. This paper has put forward a method by which Sc can be determined. ECR (CAS) has been used as a color reagent and PC as a surfactant. Conditional experiments have been made and this method has been connected to extraction separation. Tributyl phosphate (TBP) extracts Sc from rare earth elements to make a determination and good results have been obtained

Issues associated with the metalorganic chemical vapor deposition of ScGaN and YGaN alloys.

Energy Technology Data Exchange (ETDEWEB)

Koleske, Daniel David; Knapp, James Arthur; Lee, Stephen Roger; Crawford, Mary Hagerott; Creighton, James Randall; Cross, Karen Charlene; Thaler, Gerald

2009-07-01

The most energy efficient solid state white light source will likely be a combination of individually efficient red, green, and blue LED. For any multi-color approach to be successful the efficiency of deep green LEDs must be significantly improved. While traditional approaches to improve InGaN materials have yielded incremental success, we proposed a novel approach using group IIIA and IIIB nitride semiconductors to produce efficient green and high wavelength LEDs. To obtain longer wavelength LEDs in the nitrides, we attempted to combine scandium (Sc) and yttrium (Y) with gallium (Ga) to produce ScGaN and YGaN for the quantum well (QW) active regions. Based on linear extrapolation of the proposed bandgaps of ScN (2.15 eV), YN (0.8 eV) and GaN (3.4 eV), we expected that LEDs could be fabricated from the UV (410 nm) to the IR (1600 nm), and therefore cover all visible wavelengths. The growth of these novel alloys potentially provided several advantages over the more traditional InGaN QW regions including: higher growth temperatures more compatible with GaN growth, closer lattice matching to GaN, and reduced phase separation than is commonly observed in InGaN growth. One drawback to using ScGaN and YGaN films as the active regions in LEDs is that little research has been conducted on their growth, specifically, are there metalorganic precursors that are suitable for growth, are the bandgaps direct or indirect, can the materials be grown directly on GaN with a minimal defect formation, as well as other issues related to growth. The major impediment to the growth of ScGaN and YGaN alloys was the low volatility of metalorganic precursors. Despite this impediment some progress was made in incorporation of Sc and Y into GaN which is detailed in this report. Primarily, we were able to incorporate up to 5 x 10{sup 18} cm{sup -3} Y atoms into a GaN film, which are far below the alloy concentrations needed to evaluate the YGaN optical properties. After a no-cost extension was

40 CFR 82.70 - Nonessential Class II products and exceptions.

Science.gov (United States)

2010-07-01

... provide for motor vehicle safety in accordance with Federal Motor Vehicle Safety Standards until January 1... 21 CFR 2.125(e); (ii) Lubricants, coatings or cleaning fluids for electrical or electronic equipment...; (iii) Lubricants, coatings or cleaning fluids used for aircraft maintenance, which contain class II...

78 FR 48294 - Amendment of Class E Airspace; Mason, TX

Science.gov (United States)

2013-08-08

...-1141; Airspace Docket No. 12-ASW-12] Amendment of Class E Airspace; Mason, TX AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule. SUMMARY: This action amends Class E airspace at Mason, TX... Approach Procedures at Mason County Airport. This action enhances the safety and management of Instrument...

Lanthanide-doped Na xScF 3+ x nanocrystals: Crystal structure evolution and multicolor tuning

KAUST Repository

Teng, Xue

2012-05-23

Rare-earth-based nanomaterials have recently drawn considerable attention because of their unique energy upconversion (UC) capabilities. However, studies of Sc 3+-based nanomaterials are still absent. Herein we report the synthesis and fine control of Na xScF 3+x nanocrystals by tuning of the ratio of oleic acid (OA, polar surfactant) to 1-octadecene (OD, nonpolar solvent). When the OA:OD ratio was increased from low (3:17) to high (3:7), the nanocrystals changed from pure monoclinic phase (Na 3ScF 6) to pure hexagonal phase (NaScF 4) via a transition stage at an intermediate OA:OD ratio (3:9) where a mixture of nanocrystals in monoclinic and hexagonal phases was obtained and the coexistence of the two phases inside individual nanocrystals was also observed. More significantly, because of the small radius of Sc 3+, Na xScF 3+x:Yb/Er nanocrystals show different UC emission from that of NaYF 4:Yb/Er nanocrystals, which broadens the applications of rare-earth-based nanomaterials ranging from optical communications to disease diagnosis. © 2012 American Chemical Society.

A novel fusion protein of IP10-scFv retains antibody specificity and chemokine function

Energy Technology Data Exchange (ETDEWEB)

Junqing, Guo; Liu, Chen; Hongwu, Ai; Jiannian, Jing; Jiyong, Zhou; Chuyu, Zhang; Shangyou, You

2004-07-23

We combined the specificity of tumor-specific antibody with the chemokine function of interferon-{gamma} inducible protein 10 (IP-10) to recruit immune effector cells in the vicinity of tumor cells. A novel fusion protein of IP10-scFv was constructed by fusing mouse IP-10 to V{sub H} region of single-chain Fv fragment (scFv) against acidic isoferritin (AIF), and expressed in NS0 murine myeloma cells. The IP10-scFv fusion protein was shown to maintain the specificity of the antiAIF scFv with similar affinity constant, and bind to the human hepatocarcinoma SMMC 7721 cells secreting AIF as well as the activated mouse T lymphocytes expressing CXCR3 receptor. Furthermore, the IP10-scFv protein either in solution or bound on the surface of SMMC 7721 cells induced significant chemotaxis of mouse T cells in vitro. The results indicate that the IP10-scFv fusion protein possesses both bioactivities of the tumor-specific antibody and IP-10 chemokine, suggesting its possibility to induce an enhanced immune response against the residual tumor cells in vivo.

A single amino acid mutation in Spo0A results in sporulation deficiency of Paenibacillus polymyxa SC2.

Science.gov (United States)

Hou, Xiaoyang; Yu, Xiaoning; Du, Binghai; Liu, Kai; Yao, Liangtong; Zhang, Sicheng; Selin, C; Fernando, W G D; Wang, Chengqiang; Ding, Yanqin

2016-01-01

Sporulating bacteria such as Bacillus subtilis and Paenibacillus polymyxa exhibit sporulation deficiencies during their lifetime in a laboratory environment. In this study, spontaneous mutants SC2-M1 and SC2-M2, of P. polymyxa SC2 lost the ability to form endospores. A global genetic and transcriptomic analysis of wild-type SC2 and spontaneous mutants was carried out. Genome resequencing analysis revealed 14 variants in the genome of SC2-M1, including three insertions and deletions (indels), 10 single nucleotide variations (SNVs) and one intrachromosomal translocation (ITX). There were nine variants in the genome of SC2-M2, including two indels and seven SNVs. Transcriptomic analysis revealed that 266 and 272 genes showed significant differences in expression in SC2-M1 and SC2-M2, respectively, compared with the wild-type SC2. Besides sporulation-related genes, genes related to exopolysaccharide biosynthesis (eps), antibiotic (fusaricidin) synthesis, motility (flgB) and other functions were also affected in these mutants. In SC2-M2, reversion of spo0A resulted in the complete recovery of sporulation. This is the first global analysis of mutations related to sporulation deficiency in P. polymyxa. Our results demonstrate that a SNV within spo0A caused the sporulation deficiency of SC2-M2 and provide strong evidence that an arginine residue at position 211 is essential for the function of Spo0A. Copyright © 2016 The Author(s). Published by Elsevier Masson SAS.. All rights reserved.

Optimum Safety Levels for Breakwaters

DEFF Research Database (Denmark)

Burcharth, H. F.; Sørensen, John Dalsgaard

2005-01-01

Optimum design safety levels for rock and cube armoured rubble mound breakwaters without superstructure are investigated by numerical simulations on the basis of minimization of the total costs over the service life of the structure, taking into account typical uncertainties related to wave...... statistics and structure response. The study comprises the influence of interest rate, service lifetime, downtime costs and damage accumulation. Design limit states and safety classes for breakwaters are discussed. The results indicate that optimum safety levels are somewhat higher than the safety levels...

Sci-Fri AM: Quality, Safety, and Professional Issues 03: The Increasing Costs of Shielding Diagnostic CT Scanners in Ontario

Energy Technology Data Exchange (ETDEWEB)

Richer, Jeff; Frimeth, Jeff; Nesbitt, James [Windsor Regional Hospital, Xspect Inc., XRCT Inc. (Canada)

2016-08-15

Purpose: In Ontario, shielding for all X-ray machines, including CT scanners, must be evaluated according to Safety Code 20A (Health Canada, 1983) which is based on NCRP-49 (NCRP, 1976). NCRP-147 (NCRP, 2004) is the international standard for shielding calculations of CT scanners and is also referenced in Safety Code 35 (Health Canada, 2008) which, was published to supersede SC20A. The goal of this work is to demonstrate the cost effectiveness of NCRP-147 for CT scanner shielding. Methods: CT scanner shielding calculations are performed using SC20A and NCRP-147: A room located on the third floor with the nearest building 75m away A room with high occupancy uncontrolled adjacent spaces Two side by side rooms on the main floor Results: 1. SC20A: The exterior windows required 0.1mm of Pb to protect the public who may occupy the building at 75m. 1. NCRP-147: No additional shielding required. 2. SC20A: Two walls adjacent to high occupancy uncontrolled space required an additional 1.58mm Pb. 2. NCRP-147: No additional shielding required. 3. SC20A: The entire floor and ceiling slabs in both rooms required an additional 0.79mm Pb. In addition, 0.79mm Pb was added to the walls from the ceiling to overlap the existing Pb shielding in the walls. 3. NCRP-147: No additional shielding required. Conclusion: The application of NCRP Report No. 147 affords the required protection to staff and the public, in the true spirit of the ALARA principle, taking into account relevant social and economic factors.

AlScN thin film based surface acoustic wave devices with enhanced microfluidic performance

OpenAIRE

Wang, Wenbo; Fu, Yong Qing; Chen, Jinju; Xuan, Weipeng; Chen, Jinkai; Mayrhofer, Paul; Duan, Pengfei; Bittner, Elmar; Luo, Jikui

2016-01-01

This paper reports the characterization of scandium aluminum nitride (Al1−x Sc x N, x  =  27%) films and discusses surface acoustic wave (SAW) devices based on them. Both AlScN and AlN films were deposited on silicon by sputtering and possessed columnar microstructures with (0 0 0 2) crystal orientation. The AlScN/Si SAW devices showed improved electromechanical coupling coefficients (K 2, ~2%) compared with pure AlN films (

Undergraduate Organic Chemistry Laboratory Safety

Science.gov (United States)

Luckenbaugh, Raymond W.

1996-11-01

Each organic chemistry student should become familiar with the educational and governmental laboratory safety requirements. One method for teaching laboratory safety is to assign each student to locate safety resources for a specific class laboratory experiment. The student should obtain toxicity and hazardous information for all chemicals used or produced during the assigned experiment. For example, what is the LD50 or LC50 for each chemical? Are there any specific hazards for these chemicals, carcinogen, mutagen, teratogen, neurotixin, chronic toxin, corrosive, flammable, or explosive agent? The school's "Chemical Hygiene Plan", "Prudent Practices for Handling Hazardous Chemicals in the Laboratory" (National Academy Press), and "Laboratory Standards, Part 1910 - Occupational Safety and Health Standards" (Fed. Register 1/31/90, 55, 3227-3335) should be reviewed for laboratory safety requirements for the assigned experiment. For example, what are the procedures for safe handling of vacuum systems, if a vacuum distillation is used in the assigned experiment? The literature survey must be submitted to the laboratory instructor one week prior to the laboratory session for review and approval. The student should then give a short presentation to the class on the chemicals' toxicity and hazards and describe the safety precautions that must be followed. This procedure gives the student first-hand knowledge on how to find and evaluate information to meet laboartory safety requirements.

Avance normativo del SC 8 de AENOR “Conservación, restauración y rehabilitación de edificios” = Standardisation Advance of AENOR SC 8 “Conservation, Restoration and Rehabilitation of Buildings”

OpenAIRE

Recopar, Editor

2014-01-01

Avance normativo del SC 8 de AENOR “Conservación, restauración y rehabilitación de edificios” = Standardisation Advance of AENOR SC 8 “Conservation, Restoration and Rehabilitation of Buildings”

Cross-sections of 45Sc(n,2n)44m,gSc reaction from the reaction threshold to 20 MeV

International Nuclear Information System (INIS)

Luo, J.; Peking Univ., Beijing; Liu, R.; Jiang, L.; Liu, Z.; Sun, G.; Ge, S.

2013-01-01

Cross sections of 45 Sc(n,2n) 44m,g Sc reactions and their isomeric cross section ratios σ m /σ g have been measured at three neutron energies between 13.5 and 14.8 MeV using the activation technique. The pure cross section of the groundstate was then obtained by utilizing the absolute cross section of the metastable state and analysis methods of residual nuclear decay. The monoenergetic neutron beam was produced via the 3 H(d, n) 4 He reaction. The cross sections were also estimated with the TALYS-1.2 nuclear model code using different level density options, at neutron energies varying from the reaction threshold to 20 MeV. Results are also discussed and compared with some corresponding values found in the literature. (orig.)

Effect of Trace Be and Sc Additions on the Mechanical Properties of A357 Alloys

Directory of Open Access Journals (Sweden)

Yu-Chih Tzeng

2018-03-01

Full Text Available The effect of the addition of Be and Sc on the microstructure and mechanical properties of A357 alloy were systematically investigated. The results show that the addition of small amounts of Be and Sc could change the acicular structure of iron-bearing intermetallic compounds to harmless compact Al-Fe-Si and Sc-Fe iron-bearing intermetallic compounds. Compact iron-bearing intermetallic compounds could improve fluidity, causing a reduction in interdendritic shrinkage during solidification. The addition of 0.05 wt % Be enhanced the quality index of the A357 alloy by 11% and increased the notch-yield ratio of fracture toughness by 4.5%. In contrast, the addition of 0.05 wt % Sc increased the quality index and the notch to yield ratio of fracture toughness up to 17% and 9%, respectively. Therefore, the microstructure and mechanical properties of the A357 alloy could be improved by substituting Be with Sc.

Reactive diffusion in Sc/Si multilayer X-ray mirrors with CrB2 barrier layers

International Nuclear Information System (INIS)

Pershyn, Y.P.; Zubarev, E.N.; Kondratenko, V.V.; Sevryukova, V.A.; Kurbatova, S.V.

2011-01-01

Processes undergoing in Sc/Si multilayer X-ray mirrors (MXMs) with periods of ∝27 nm and barrier layers of CrB 2 0.3- and 0.7-nm thick within the temperature range of 420-780 K were studied by methods of small-angle X-ray reflectivity (λ=0.154 nm) and cross-sectional transmission electron microscopy. All layers with the exception of Sc ones are amorphous. Barrier layers are stable at least up to a temperature of 625 K and double the activation energy of diffusional intermixing at moderate temperatures. Introduction of barriers improves the thermal stability of Sc/Si MXMs at least by 80 degrees. Diffusion of Si atoms through barrier layers into Sc layers with formation of silicides was shown to be the main degradation mechanism of MXMs. A comparison of the stability for Sc/Si MXMs with different barriers published in the literature is conducted. The ways of further improvement of barrier properties are discussed. (orig.)

75 FR 53876 - Proposed Establishment of Class E Airspace; Berryville, AR

Science.gov (United States)

2010-09-02

... Class E Airspace; Berryville, AR AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). SUMMARY: This action proposes to establish Class E airspace at Berryville, AR... SIAPs operations at Carroll County Airport, Berryville, AR. Controlled airspace is needed for the safety...

Ferromagnetism carried by highly delocalized hybrid states in Sc-doped ZnO thin films

KAUST Repository

Benali Kanoun, Mohammed; Goumri-Said, Souraya; Manchon, Aurelien; Schwingenschlö gl, Udo

2012-01-01

We present first-principles results for Sc-doped ZnOthin films. Neighboring Sc atoms in the surface and/or subsurface layers are found to be coupled ferromagnetically, where only two of the possible configurations induce spin polarization

AERB information booklet: personal protective equipment- safety footwear

International Nuclear Information System (INIS)

1992-01-01

The main classes of safety footwear required for industrial operations in the units of Department of Atomic Energy are the following; leather safety boots and shoes, firemen's leather boots - Wellington type, electrical safety shoes, chemical safety shoes, shoes suitable for mining operations. The criteria to be adopted for selection of safety shoes for nuclear installations are given. (M.K.V.). 5 annexures, 1 appendix

Analysis of effectiveness, safety and optimization of tocilizumab in a cohort of patients with rheumatoid arthritis in clinical practice.

Science.gov (United States)

Mena-Vázquez, Natalia; Manrique-Arija, Sara; Rojas-Giménez, Marta; Ureña-Garnica, Inmaculada; Jiménez-Núñez, Francisco G; Fernández-Nebro, Antonio

2017-07-01

To evaluate the effectiveness and safety of tocilizumab (TCZ) in patients with rheumatoid arthritis (RA) in clinical practice, establishing the optimized regimen and switching from intravenous (IV) to subcutaneous (SC) therapy. Retrospective observational study. We included 53 RA patients treated with TCZ. The main outcome was TCZ effectiveness at week 24. Secondary outcome variables included effectiveness at week 52, therapeutic maintenance, physical function and safety. The effectiveness of optimization and the switch from IV to SC was evaluated at 3 and 6 months. The efficacy was measured with the Disease Activity Score. Paired t-tests or Wilcoxon were used to evaluate effectiveness and survival time using Kaplan-Meier. The proportion of patients who achieved remission or low disease activity at weeks 24 and 52 was 75.5% and 87.3%, respectively. The mean retention time (95% confidence interval [95% CI] was 81.7 months [76.6-86.7]). Twenty-one of 53 patients (39.6%) optimized the TCZ dose and 35 patients switched from IV TCZ to SC, with no changes in effectiveness. The adverse event rate was 13.6 events/100 patient-years. Tocilizumab appears to be effective and safe in RA in clinical practice. The optimized regimen appears to be effective in most patients in remission, even when they change from IV to SC. Copyright © 2017 Elsevier España, S.L.U. and Sociedad Española de Reumatología y Colegio Mexicano de Reumatología. All rights reserved.

Effect of lectin (ScLL on fibroblasts stimulated with LPS - an in vitro study

Directory of Open Access Journals (Sweden)

Manuella Verdinelli de Paula REIS

Full Text Available Abstract: The lectin (ScLL extracted from the Synadenium carinatum plant has been evaluated as an immunomodulator in diseases such as asthma, neosporosis and leishmaniasis. However, it has not yet been evaluated in the oral cavity. This study evaluated the effect of ScLL on viability, proliferation and release of IL-10 in human gingival fibroblasts (HGF stimulated with lipopolysaccharide (LPS. HGF were stimulated with LPS 1 µg/ml and treated with ScLL in concentrations of 10, 5 and 2 µg/ml for 1 and 5 h, and evaluated by flow cytometry for viability, apoptosis (initial/advanced and necrosis. The supernatant was collected to detect release of IL-10 by ELISA. The proliferation was assessed with the BrdU assay. Positive control consisted of cells maintained in Dulbecco's Modified Eagles Medium (DMEM, and the negative control, of those kept in tap water. Data were analyzed by ANOVA and Dunnett's test (α = 0.05. No significant difference was found for ScLL concentrations regarding viability or initial and advanced apoptosis (p=0.455. All the groups, including the positive control, had a significantly lower necrosis parameter than negative control at 5 h (p < 0.001. No difference was found for proliferation among the experimental groups (p = 0.832. ScLL at 5 and 2 µg/ml resulted in a lower release of IL-10 than positive and negative controls at 5 h (p = 0.047. The results indicated that ScLL concentrations tested were not cytotoxic, and had no effect on proliferation and release of IL-10 parameters. A thorough understanding of ScLL, regarding its immunomodulatory potential, may open the door to new perspectives for dentistry.

Safety, Tolerability, Pharmacokinetics, and Pharmacodynamics of the CGRP Binding Monoclonal Antibody LY2951742 (Galcanezumab in Healthy Volunteers

Directory of Open Access Journals (Sweden)

David Monteith

2017-10-01

Full Text Available Background: Calcitonin gene-related peptide (CGRP is pivotal in the pathophysiology of migraine headaches and represents a promising target for migraine treatment. The humanized monoclonal antibody galcanezumab (LY2951742 binds to CGRP and may be effective in migraine prophylaxis.Objectives: The primary objective was to evaluate the safety and tolerability of single and multiple doses of galcanezumab in humans. Secondary objectives included assessing the pharmacokinetics and evaluating target engagement.Methods: A double-blind, randomized, placebo-controlled study (NCT 01337596 with single escalating and multiple subcutaneous (SC doses of galcanezumab was performed in healthy male volunteers. Single doses of 1, 5, 25, 75, 200, and 600 mg of galcanezumab (n = 7/dose or placebo (n = 2/dose were injected SC in six consecutive cohorts of nine subjects each. One cohort of nine subjects received multiple (4 150 mg doses of galcanezumab or placebo every other week. Target engagement was evaluated by measuring inhibition of capsaicin-induced increase in dermal blood flow (DBF.Findings: Sixty-three subjects were randomized and included in the safety analyses. Galcanezumab was well tolerated in single doses (1–600 mg SC and consecutive doses (150 mg SC. There was no dose-dependent difference in type or frequency of treatment-emergent adverse events, and no clinically meaningful difference when compared with placebo. Pharmacokinetics were linear. Galcanezumab induced a robust, dose-dependent, and durable inhibition of capsaicin-induced increase in DBF, supporting the continued clinical development of galcanezumab for prophylaxis in migraine patients.

Isolation and characterization of anti c-met single chain fragment variable (scFv) antibodies.

Science.gov (United States)

Qamsari, Elmira Safaie; Sharifzadeh, Zahra; Bagheri, Salman; Riazi-Rad, Farhad; Younesi, Vahid; Abolhassani, Mohsen; Ghaderi, Sepideh Safaei; Baradaran, Behzad; Somi, Mohammad Hossein; Yousefi, Mehdi

2017-12-01

The receptor tyrosine kinase (RTK) Met is the cell surface receptor for hepatocyte growth factor (HGF) involved in invasive growth programs during embryogenesis and tumorgenesis. There is compelling evidence suggesting important roles for c-Met in colorectal cancer proliferation, migration, invasion, angiogenesis, and survival. Hence, a molecular inhibitor of an extracellular domain of c-Met receptor that blocks c-Met-cell surface interactions could be of great thera-peutic importance. In an attempt to develop molecular inhibitors of c-Met, single chain variable fragment (scFv) phage display libraries Tomlinson I + J against a specific synthetic oligopeptide from the extracellular domain of c-Met receptor were screened; selected scFv were then characterized using various immune techniques. Three c-Met specific scFv (ES1, ES2, and ES3) were selected following five rounds of panning procedures. The scFv showed specific binding to c-Met receptor, and significantly inhibited proliferation responses of a human colorectal carcinoma cell line (HCT-116). Moreover, anti- apoptotic effects of selected scFv antibodies on the HCT-116 cell line were also evaluated using Annexin V/PI assays. The results demonstrated rates of apoptotic cell death of 46.0, 25.5, and 37.8% among these cells were induced by use of ES1, ES2, and ES3, respectively. The results demonstrated ability to successfully isolate/char-acterize specific c-Met scFv that could ultimately have a great therapeutic potential in immuno-therapies against (colorectal) cancers.

Topological phase, electronic, magnetic and optical properties of ScPdBi compound with Gd, Np and Cm impurities

Energy Technology Data Exchange (ETDEWEB)

Narimani, Mitra; Nourbakhsh, Zahra, E-mail: z.nourbakhsh@sci.ui.ac.ir

2017-07-15

Highlights: • Gd, Np and Cm impurities induce the magnetic moment in ScPdBi compound. • ScPdBi compound with Gd, Np and Cm impurities has normal band order. • The ε(0) and R(0) increase by increasing the atomic number of X atom. - Abstract: The electronic, magnetic and optical properties of X-doped ScPdBi (X = Gd, Np, Cm) are investigated in the framework of density functional theory. The exchange-correlation potential is treated using generalized gradient approximation with Coulomb interaction parameter. The band order and energy band gap of X-doped ScPdBi are investigated by calculation of band structure. The effect of doping impurity on magnetic properties of ScPdBi compound is studied by calculation of total and partial magnetic moments of X-doped ScPdBi compound. Furthermore, the optical properties of X-doped ScPdBi are calculated and compared in the energy range of 0–25 eV.

Design and initial characterization of the SC-200 proteomics standard mixture.

Science.gov (United States)

Bauman, Andrew; Higdon, Roger; Rapson, Sean; Loiue, Brenton; Hogan, Jason; Stacy, Robin; Napuli, Alberto; Guo, Wenjin; van Voorhis, Wesley; Roach, Jared; Lu, Vincent; Landorf, Elizabeth; Stewart, Elizabeth; Kolker, Natali; Collart, Frank; Myler, Peter; van Belle, Gerald; Kolker, Eugene

2011-01-01

High-throughput (HTP) proteomics studies generate large amounts of data. Interpretation of these data requires effective approaches to distinguish noise from biological signal, particularly as instrument and computational capacity increase and studies become more complex. Resolving this issue requires validated and reproducible methods and models, which in turn requires complex experimental and computational standards. The absence of appropriate standards and data sets for validating experimental and computational workflows hinders the development of HTP proteomics methods. Most protein standards are simple mixtures of proteins or peptides, or undercharacterized reference standards in which the identity and concentration of the constituent proteins is unknown. The Seattle Children's 200 (SC-200) proposed proteomics standard mixture is the next step toward developing realistic, fully characterized HTP proteomics standards. The SC-200 exhibits a unique modular design to extend its functionality, and consists of 200 proteins of known identities and molar concentrations from 6 microbial genomes, distributed into 10 molar concentration tiers spanning a 1,000-fold range. We describe the SC-200's design, potential uses, and initial characterization. We identified 84% of SC-200 proteins with an LTQ-Orbitrap and 65% with an LTQ-Velos (false discovery rate = 1% for both). There were obvious trends in success rate, sequence coverage, and spectral counts with protein concentration; however, protein identification, sequence coverage, and spectral counts vary greatly within concentration levels.

The Use of Theatre Tours in Road Safety Education.

Science.gov (United States)

Powney, Janet; And Others

The Scottish Road Safety Campaign and the Road Safety Council of Wales have made a large investment in theater tours as a method of providing road safety education. This study aimed to evaluate the effectiveness of a road safety message delivered by a theater group, Road Safety Officers (RSOs), or, teachers for pupils in upper secondary classes.…

Soil class around me Serpong experimental power reactor (EPR) site plan base on micro tremor data

International Nuclear Information System (INIS)

Marjiyono; Soehaimi A; Hadi Suntoko; Yuliastuti; Syaeful H

2015-01-01

Surface geological characteristics has an important role on site response analysis in a region. In regard with experimental power reactor (EPR) construction plan in Serpong, the subsurface modeling from combination array and single station micro tremor data was done. The array and single station micro tremor measurement were performed in 9 and 90 sites, respectively, at ± 1 km radius around the EPR site plan. The Vs30 value was calculated from shear wave velocity structure around the investigated area. The soil classification based on Vs30 in the investigated area generally consists of SD (medium soil) and SC (soft rock) class. The EPR site plan its self in the SD class region. (author)

Effects of co-sintering in self-standing CGO/YSZ and CGO/ ScYSZ dense bi-layers

DEFF Research Database (Denmark)

Teocoli, Francesca; Ni, De Wei; Brodersen, Karen

2014-01-01

-layers are critical due to the mismatch of thermo-mechanical and sintering properties among the materials. Despite the better sinteractivity of ScYSZ, the self-standing CGO/ScYSZ bilayer presents more challenges in terms of densification compared with the CGO/YSZ bi-layer. In particular, above 1200 C, ScYSZ and CGO......-standing bi-layered electrolyte system. The combined use of thermo-mechanical analysis, optical dilatometry, and scanning electron microscopy ensures a systematic characterization of both the individual layers and CGO/YSZ and CGO/ScYSZ bi-layered laminates. The results of the co-firing process of the bi...

Effect of Recrystallization and Natural Aging on Mechanical Properties of Al-Zn-Mg-Cu-Sc Alloys

International Nuclear Information System (INIS)

Yu, Min Kyu; Hong, Soon Hyung; Kwon, Oh Yeol; Lee, Yong Yeon

2015-01-01

In this study, the recrystallization volume fraction of the Al-Zn-Mg-Cu-Sc alloy after solid solution heat treatment varied with different temperatures (445℃ - 465℃). The highest elongation of the Al-Zn-Mg-Cu-Sc alloy was obtained at 465℃. Further, the hardness and strength of the solid solution heat treated Al-Zn-Mg-Cu-Sc alloy increased at room temperature due to G.P zone precipitates. The results confirmed that we can obtain advanced mechanical properties for the Al-Zn-Mg-Cu-Sc alloy from solid solution heat treatment and natural aging.

76 FR 53359 - Proposed Establishment of Class E Airspace; Nashville, AR

Science.gov (United States)

2011-08-26

...-0497; Airspace Docket No. 11-ASW-4] Proposed Establishment of Class E Airspace; Nashville, AR AGENCY... action proposes to establish Class E airspace at Nashville, AR. Controlled airspace is necessary to... approach procedures at Howard County Airport, Nashville, AR. Controlled airspace is needed for the safety...

77 FR 16783 - Proposed Amendment of Class E Airspace; Orlando, FL

Science.gov (United States)

2012-03-22

...-0503; Airspace Docket No. 11-ASO-19] Proposed Amendment of Class E Airspace; Orlando, FL AGENCY... action proposes to amend Class E Airspace at Orlando, FL, as new Standard Instrument Approach Procedures have been developed at Orlando Executive Airport. This action would enhance the safety and airspace...

Production of in vivo biotinylated scFv specific to almond (Prunus dulcis) proteins by recombinant Pichia pastoris.

Science.gov (United States)

de la Cruz, Silvia; Alcocer, Marcos; Madrid, Raquel; García, Aina; Martín, Rosario; González, Isabel; García, Teresa

2016-06-10

The methylotropic yeast Pichia pastoris has demonstrated its suitability for large-scale production of recombinant proteins. As an eukaryotic organism P. pastoris presents a series of advantages at expression and processing of heterologous proteins when compared with Escherichia coli. In this work, P. pastoris has been used to express a scFv from a human synthetic library previously shown to bind almond proteins. In order to facilitate purification and post processing manipulations, the scFv was engineered with a C-terminal tag and biotinylated in vivo. After purification, biotinylated scFv were bound to avidin conjugated with HRP producing a multimeric scFv. The multimeric scFv showed to maintain their ability to recognize almond protein when assayed in ELISA, reaching a LOD of 470mgkg(-1). This study describes an easy method to produce large quantities of in vivo biotinylated scFv in P. pastoris. By substituting the enzyme or fluorochromes linked to avidin, it will be possible to generate a diverse number of multimeric scFv as probes to suit different analytical platforms in the detection of almond in food products. Copyright © 2016 Elsevier B.V. All rights reserved.

A Sub-µW Tuneable Switched-Capacitor Amplifier-Filter for Neural Recording Using a Class-C Inverter

Directory of Open Access Journals (Sweden)

A Ghorbani-Nejad

2013-12-01

Full Text Available A two stage sub-µW Inverter-based switched-capacitor amplifier-filter is presented which is capable of amplifying both spikes and local field potentials (LFP signals. Here we employ a switched capacitor technique for frequency tuning and reducing of 1/f noise of two stages. The reduction of power consumption is very necessary for neural recording devices however, in switched capacitor (SC circuits OTA is a major building block that consumes most of the power. Therefore an OTA-less technique utilizing a class-C inverter is employed that significantly reduces the power consumption. A detailed analysis of noise performance for the inverter-based SC circuits is presented. A mathematical model useful for analysis of such SC integrators is derived and a good comparison is obtained between simulation and analytical technique. With a supply voltage of 0.7V and using 0.18 µm CMOS technology, this design can achieves a power consumption of about 538 nW. The designed amplifier-filter has the gains 18.6 dB and 28.2 dB for low pass only and cascaded filter, respectively. By applying different sampling frequencies, the filter attains a reconfigurable bandwidth.

Calibration of the DLP-SC-3300-02 probe

DEFF Research Database (Denmark)

Pivnenko, Sergey; Breinbjerg, Olav

This report douments the calibration measurement of the DLP-SC-3300-02 dual-linearly polarized near-field probe. The measurement comprises radiation pattern, diretivity, gain, spetra of spherial wave coefients, polarization charateristis, and complex channel balance at 41 frequencies, as well...

Zero lattice mismatch and twin-free single crystalline ScN buffer layers for GaN growth on silicon

Energy Technology Data Exchange (ETDEWEB)

Lupina, L.; Zoellner, M. H.; Dietrich, B.; Capellini, G. [IHP, Im Technologiepark 25, 15236 Frankfurt, Oder (Germany); Niermann, T.; Lehmann, M. [Technische Universität Berlin, Institut für Optik und Atomare Physik, Straße des 17. Juni 135, 10623 Berlin (Germany); Thapa, S. B.; Haeberlen, M.; Storck, P. [SILTRONIC AG, Hanns-Seidel-Platz 4, 81737 München (Germany); Schroeder, T. [IHP, Im Technologiepark 25, 15236 Frankfurt, Oder (Germany); BTU Cottbus, Konrad-Zuse-Str. 1, 03046 Cottbus (Germany)

2015-11-16

We report the growth of thin ScN layers deposited by plasma-assisted molecular beam epitaxy on Sc{sub 2}O{sub 3}/Y{sub 2}O{sub 3}/Si(111) substrates. Using x-ray diffraction, Raman spectroscopy, and transmission electron microscopy, we find that ScN films grown at 600 °C are single crystalline, twin-free with rock-salt crystal structure, and exhibit a direct optical band gap of 2.2 eV. A high degree of crystalline perfection and a very good lattice matching between ScN and GaN (misfit < 0.1%) makes the ScN/Sc{sub 2}O{sub 3}/Y{sub 2}O{sub 3} buffer system a very promising template for the growth of high quality GaN layers on silicon.

X-ray spectra, chemical bonding, and electron structure of ScM2Si2 (M = Fe, Co, Ni)

International Nuclear Information System (INIS)

Shcherba, I.D.; Kotur, B.Ya.

1990-01-01

In a study of the interaction of the components in the ternary systems Sc-M-Si (where M is a 3d transition metal) it was established that there are compounds of the empirical formula ScM 2 Si 2 (M = Fe, Co, Ni). They crystallize in two structural types, HfFe 2 Si 2 (the compound ScFe 2 Si 2 ) and CeGa 2 Al 2 (ScCo 2 Si 2 and ScNi 2 Si 2 ) (ref. 1), leading to different coordination environment of the atoms in the structures of the compounds. With the aim of investigating the electron structure and the type ofin these compounds, they authors made a systematic x-ray spectral investigation with simultaneous analysis of the crystal structures of ScM 2 Si 2

Seismic and environmental qualification of class IE equipment manufactured in Spain

International Nuclear Information System (INIS)

Gerini, P.; Lumbreras, A.; Naredo, F.

1978-01-01

Nuclear power plant instrumentation and control design is affected by several factors such as various plant operating conditions, transient response capability, safety requirements and changes in IEEE standards. Recent upgraded IEEE standards that call for Qualification of all Safety related I anc C equipment, namely IEEE 323 (Qualifying Class IE Electric Equipment for nuclear power generating stations) and its daughter Standard IEEE 344 (Recommended Practices for Seismic Qualification of Class IE Equipment for nuclear power generating stations) have been endorsed by the United States Nuclear Regulatory Commission through the issuance of corresponding Regulatory Guides. The author describes the Qualification requirements applicable to the Class IE I and C Components made in Spain for the different vintages of plants, and the programs implemented or plans established by Westinghouse to fulfill those requirements. (author)

World class manufacturing in metallurgical enterprise

OpenAIRE

B. Gajdzik

2013-01-01

World Class Manufacturing (WCM) assumes increase of efficiency of the company by elimination of all the losses, wastage and dangers of safety. In ArcelorMittal the concept of WCM is implemented in particular enterprises within the capital group. In this publication the activities conducted in some of those enterprises are described.

Bulk viscosity in 2SC quark matter

International Nuclear Information System (INIS)

Alford, Mark G; Schmitt, Andreas

2007-01-01

The bulk viscosity of three-flavour colour-superconducting quark matter originating from the nonleptonic process u + s ↔ u + d is computed. It is assumed that up and down quarks form Cooper pairs while the strange quark remains unpaired (2SC phase). A general derivation of the rate of strangeness production is presented, involving contributions from a multitude of different subprocesses, including subprocesses that involve different numbers of gapped quarks as well as creation and annihilation of particles in the condensate. The rate is then used to compute the bulk viscosity as a function of the temperature, for an external oscillation frequency typical of a compact star r-mode. We find that, for temperatures far below the critical temperature T c for 2SC pairing, the bulk viscosity of colour-superconducting quark matter is suppressed relative to that of unpaired quark matter, but for T ∼> T c /30 the colour-superconducting quark matter has a higher bulk viscosity. This is potentially relevant for the suppression of r-mode instabilities early in the life of a compact star

75 FR 6592 - Proposed Amendment of Class E Airspace; Emmetsburg, IA

Science.gov (United States)

2010-02-10

...-1153; Airspace Docket No. 09-ACE-13] Proposed Amendment of Class E Airspace; Emmetsburg, IA AGENCY... action proposes to amend Class E airspace at Emmetsburg, IA. Additional controlled airspace is necessary..., Emmetsburg, IA. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules...

76 FR 3571 - Proposed Establishment of Class E Airspace; Kahului, HI

Science.gov (United States)

2011-01-20

...-1233; Airspace Docket No. 10-AWP-21] Proposed Establishment of Class E Airspace; Kahului, HI AGENCY... action proposes to establish Class E airspace at Kahului Airport, Kahului, HI. Controlled airspace is... procedures at Kahului Airport, Kahului, HI. The FAA is proposing this action to enhance the safety and...

75 FR 6594 - Proposed Amendment of Class E Airspace; Osceola, AR

Science.gov (United States)

2010-02-10

...-1183; Airspace Docket No. 09-ASW-38] Proposed Amendment of Class E Airspace; Osceola, AR AGENCY... action proposes to amend Class E airspace at Osceola, AR. Decommissioning of the Osceola non-directional beacon (NDB) at Osceola Municipal Airport, Osceola, AR, has made this action necessary for the safety and...

The Effect of Surfactant Content over Cu-Ni Coatings Electroplated by the sc-CO₂ Technique.

Science.gov (United States)

Chuang, Ho-Chiao; Sánchez, Jorge; Cheng, Hsiang-Yun

2017-04-19

Co-plating of Cu-Ni coatings by supercritical CO₂ (sc-CO₂) and conventional electroplating processes was studied in this work. 1,4-butynediol was chosen as the surfactant and the effects of adjusting the surfactant content were described. Although the sc-CO₂ process displayed lower current efficiency, it effectively removed excess hydrogen that causes defects on the coating surface, refined grain size, reduced surface roughness, and increased electrochemical resistance. Surface roughness of coatings fabricated by the sc-CO₂ process was reduced by an average of 10%, and a maximum of 55%, compared to conventional process at different fabrication parameters. Cu-Ni coatings produced by the sc-CO₂ process displayed increased corrosion potential of ~0.05 V over Cu-Ni coatings produced by the conventional process, and 0.175 V over pure Cu coatings produced by the conventional process. For coatings ~10 µm thick, internal stress developed from the sc-CO₂ process were ~20 MPa lower than conventional process. Finally, the preferred crystal orientation of the fabricated coatings remained in the (111) direction regardless of the process used or surfactant content.

Simultaneous reduction and adsorption for immobilization of uranium from aqueous solution by nano-flake Fe-SC

Energy Technology Data Exchange (ETDEWEB)

Kong, Lingjun, E-mail: kongl_jun@163.com [School of Environmental Science and Engineering, Guangzhou University, Guangzhou, 510275 (China); Guangdong Provincial Key Laboratory of radioactive contamination control and resources, Guangzhou University, Guangzhou, 510275 (China); Guangdong Provincial Key Laboratory of Environmental Pollution Control and Remediation Technology, Sun Yat-sen University, Guangzhou, 510275 (China); Zhu, Yuting; Wang, Min; Li, Zhixuan; Tan, Zhicong; Xu, Ruibin; Tang, Hongmei; Chang, Xiangyang [School of Environmental Science and Engineering, Guangzhou University, Guangzhou, 510275 (China); Guangdong Provincial Key Laboratory of radioactive contamination control and resources, Guangzhou University, Guangzhou, 510275 (China); Xiong, Ya [Guangdong Provincial Key Laboratory of Environmental Pollution Control and Remediation Technology, Sun Yat-sen University, Guangzhou, 510275 (China); Chen, Diyun, E-mail: cdy@gzhu.edu.cn [School of Environmental Science and Engineering, Guangzhou University, Guangzhou, 510275 (China); Guangdong Provincial Key Laboratory of radioactive contamination control and resources, Guangzhou University, Guangzhou, 510275 (China)

2016-12-15

Uranium containing radioactive wastewater is seriously hazardous to the natural environment if it is being discharged directly. Herein, nano-flake like Fe loaded sludge carbon (Fe-SC) is synthesized by carbothermal process from Fe-rich sludge waste and applied in the immobilization of uranium in aqueous. Batch isotherm and kinetic adsorption experiments are adopted to investigate the adsorption behavior of Fe-SC to uranium in aqueous. XPS analyses were conducted to evaluate the immobilized mechanism. It was found that the carbonized temperature played significant role in the characteristics and immobilization ability of the resulted Fe-SC. The Fe-SC-800 carbonized at 800 °C takes more advantageous ability in immobilization of uranium from aqueous than the commercial available AC and powder zero valent iron. The adsorption behavior could be fitted well with the Langmuir isotherm adsorption model and pseudo-second order model. The equilibrium adsorption amount and rate for Fe-SC-800 is high to 148.99 mg g{sup -1} and 0.015 g mg{sup -1} min{sup -1}, respectively. Both reductive precipitation and physical adsorption are the main mechanisms of immobilization of uranium from aqueous by Fe-SC-800.

Preliminary Analysis of the Social and Scientific Impact of the UAEM-ININ M.Sc. and D.Sc. Graduate Programme in Medical Physics

Science.gov (United States)

Mitsoura, Eleni; Isaac-Olive, Keila; Torres-Garcia, Eugenio; Camacho-Lopez, Miguel Angel; Hardy-Perez, Alberto

2010-12-01

Sponsored by the International Atomic Energy Agency (IAEA) in 1994, the Instituto Nacional de Investigaciones Nucleares (ININ) started in Mexico a teaching and training programme (Diplomado) in Radiotherapy Medical Physics. Based on this experience, the Universidad Autónoma del Estado de México (UAEM) and the Instituto Nacional de Investigaciones Nucleares (ININ) launched two years later, the first Graduate Programme in Science (M.Sc. and D.Sc.), specialised in Medical Physics in Mexico. A preliminary analysis of the social and scientific impact of the UAEM-ININ Programme is presented in this work based on the achievements attained, regarding the number of graduated Medical Physicists, their geographic and academic origin, their current professional activities and the number of scientific publications produced as a result of the thesis, as well as their citations.

Safety and immunogenicity of an HIV adenoviral vector boost after DNA plasmid vaccine prime by route of administration: a randomized clinical trial.

Directory of Open Access Journals (Sweden)

Beryl A Koblin

Full Text Available In the development of HIV vaccines, improving immunogenicity while maintaining safety is critical. Route of administration can be an important factor.This multicenter, open-label, randomized trial, HVTN 069, compared routes of administration on safety and immunogenicity of a DNA vaccine prime given intramuscularly at 0, 1 and 2 months and a recombinant replication-defective adenovirus type 5 (rAd5 vaccine boost given at 6 months by intramuscular (IM, intradermal (ID, or subcutaneous (SC route. Randomization was computer-generated by a central data management center; participants and staff were not blinded to group assignment. The outcomes were vaccine reactogenicity and humoral and cellular immunogenicity. Ninety healthy, HIV-1 uninfected adults in the US and Peru, aged 18-50 were enrolled and randomized. Due to the results of the Step Study, injections with rAd5 vaccine were halted; thus 61 received the booster dose of rAd5 vaccine (IM: 20; ID:21; SC:20. After the rAd5 boost, significant differences by study arm were found in severity of headache, pain and erythema/induration. Immune responses (binding and neutralizing antibodies, IFN-γ ELISpot HIV-specific responses and CD4+ and CD8+ T-cell responses by ICS at four weeks after the rAd5 booster were not significantly different by administration route of the rAd5 vaccine boost (Binding antibody responses: IM: 66.7%; ID: 70.0%; SC: 77.8%; neutralizing antibody responses: IM: 11.1%; ID: 0.0%; SC 16.7%; ELISpot responses: IM: 46.7%; ID: 35.3%; SC: 44.4%; CD4+ T-cell responses: IM: 29.4%; ID: 20.0%; SC: 35.3%; CD8+ T-cell responses: IM: 29.4%; ID: 16.7%; SC: 50.0%.This study was limited by the reduced sample size. The higher frequency of local reactions after ID and SC administration and the lack of sufficient evidence to show that there were any differences in immunogenicity by route of administration do not support changing route of administration for the rAd5 boost.ClinicalTrials.gov NCT00384787.

VFR Class B Graphics - Aeronautical Information Services Digital Products

Data.gov (United States)

Department of Transportation — These graphics are designed to increase safety and aid pilots in gaining situational awareness within existing and redesigned Class B areas. The graphic provides an...

Development of a methodology for safety classification on a non-reactor nuclear facility illustrated using an specific example

International Nuclear Information System (INIS)

Scheuermann, F.; Lehradt, O.; Traichel, A.

2015-01-01

To realize the safety of personnel and environment systems and components of nuclear facilities are classified according to their potential danger into safety classes. Based on this classification different demands on the manufacturing quality result. The objective of this work is to present the standardized method developed by NUKEM Technologies Engineering Services for the categorization into the safety classes restricted to Non-reactor nuclear facilities (NRNF). Exemplary the methodology is used on the complex Russian normative system (four safety classes). For NRNF only the lower two safety classes are relevant. The classification into the lowest safety class 4 is accordingly if the maximum resulting dose following from clean-up actions in case of incidents/accidents remains below 20 mSv and the volume activity restrictions of set in NRB-99/2009 are met. The methodology is illustrated using an example. In short the methodology consists of: - Determination of the working time to remove consequences of incidents, - Calculation of the dose resulting from direct radiation and due to inhalation during these works. The application of this methodology avoids over-conservative approaches. As a result some previously higher classified equipment can be classified into the lower safety class.

Safety Education in the Elementary School. Fastback 170.

Science.gov (United States)

Wayne, Joseph E.

This pamphlet deals with incorporating effective safety education programs into the elementary school curriculum. Covered in a discussion of the scope and nature of the safety problem are classes of accidents (motor vehicle, home, work, and public accidents) and causes of accidents. Various functions of safety education in elementary schools are…

Assessment of the GLLB-SC potential for solid-state properties and attempts for improvement

Science.gov (United States)

Tran, Fabien; Ehsan, Sohaib; Blaha, Peter

2018-02-01

Based on the work of Gritsenko et al. (GLLB) [Phys. Rev. A 51, 1944 (1995), 10.1103/PhysRevA.51.1944], the method of Kuisma et al. [Phys. Rev. B 82, 115106 (2010), 10.1103/PhysRevB.82.115106] to calculate the band gap in solids was shown to be much more accurate than the common local density approximation (LDA) and generalized gradient approximation (GGA). The main feature of the GLLB-SC potential (SC stands for solid and correlation) is to lead to a nonzero derivative discontinuity that can be conveniently calculated and then added to the Kohn-Sham band gap for a comparison with the experimental band gap. In this work, a thorough comparison of GLLB-SC with other methods, e.g., the modified Becke-Johnson (mBJ) potential [Tran and Blaha, Phys. Rev. Lett. 102, 226401 (2009), 10.1103/PhysRevLett.102.226401], for electronic, magnetic, and density-related properties is presented. It is shown that for the band gap, GLLB-SC does not perform as well as mBJ for systems with a small band gap and strongly correlated systems, but is on average of similar accuracy as hybrid functionals. The results on itinerant metals indicate that GLLB-SC overestimates significantly the magnetic moment (much more than mBJ does), but leads to excellent results for the electric field gradient, for which mBJ is in general not recommended. In the aim of improving the results, variants of the GLLB-SC potential are also tested.

Changes in expression of Class 3 Semaphorins and their receptors during development of the rat retina and superior colliculus.

Science.gov (United States)

Sharma, Anil; LeVaillant, Chrisna J; Plant, Giles W; Harvey, Alan R

2014-07-26

Members of the Semaphorin 3 family (Sema3s) influence the development of the central nervous system, and some are implicated in regulating aspects of visual system development. However, we lack information about the timing of expression of the Sema3s with respect to different developmental epochs in the mammalian visual system. In this time-course study in the rat, we document for the first time changes in the expression of RNAs for the majority of Class 3 Semaphorins (Sema3s) and their receptor components during the development of the rat retina and superior colliculus (SC). During retinal development, transcript levels changed for all of the Sema3s examined, as well as Nrp2, Plxna2, Plxna3, and Plxna4a. In the SC there were also changes in transcript levels for all Sema3s tested, as well as Nrp1, Nrp2, Plxna1, Plxna2, Plxna3, and Plxna4a. These changes correlate with well-established epochs, and our data suggest that the Sema3s could influence retinal ganglion cell (RGC) apoptosis, patterning and connectivity in the maturing retina and SC, and perhaps guidance of RGC and cortical axons in the SC. Functionally we found that SEMA3A, SEMA3C, SEMA3E, and SEMA3F proteins collapsed purified postnatal day 1 RGC growth cones in vitro. Significantly this is a developmental stage when RGCs are growing into and within the SC and are exposed to Sema3 ligands. These new data describing the overall temporal regulation of Sema3 expression in the rat retina and SC provide a platform for further work characterising the functional impact of these proteins on the development and maturation of mammalian visual pathways.

Properties of the low-lying negative parity states in 45Sc

International Nuclear Information System (INIS)

Chevallier, J.; Haas, B.; Schulz, N.; Toulemonde, M.

1975-01-01

The electromagnetic decay of negative parity states in 45 Sc up to an excitation energy of 2107keV have been investigated via the 42 Ca(α,pγ) 45 Sc reaction at a bombarding energy of 10.5MeV. Spin and lifetime of the levels as well as branching and mixing ratios of their decay γ-rays have been obtained from proton-gamma angular correlation measurements. Calculations based on the strong coupling model have been performed. The results are compared with experiment [fr

Structural characteristics of ScBx genes controlling the biosynthesis of hydroxamic acids in rye (Secale cereale L.).

Science.gov (United States)

Bakera, Beata; Makowska, Bogna; Groszyk, Jolanta; Niziołek, Michał; Orczyk, Wacław; Bolibok-Brągoszewska, Hanna; Hromada-Judycka, Aneta; Rakoczy-Trojanowska, Monika

2015-08-01

Benzoxazinoids (BX) are major secondary metabolites of gramineous plants that play an important role in disease resistance and allelopathy. They also have many other unique properties including anti-bacterial and anti-fungal activity, and the ability to reduce alfa-amylase activity. The biosynthesis and modification of BX are controlled by the genes Bx1 ÷ Bx10, GT and glu, and the majority of these Bx genes have been mapped in maize, wheat and rye. However, the genetic basis of BX biosynthesis remains largely uncharacterized apart from some data from maize and wheat. The aim of this study was to isolate, sequence and characterize five genes (ScBx1, ScBx2, ScBx3, ScBx4 and ScBx5) encoding enzymes involved in the synthesis of DIBOA, an important defense compound of rye. Using a modified 3D procedure of BAC library screening, seven BAC clones containing all of the ScBx genes were isolated and sequenced. Bioinformatic analyses of the resulting contigs were used to examine the structure and other features of these genes, including their promoters, introns and 3'UTRs. Comparative analysis showed that the ScBx genes are similar to those of other Poaceae species, especially to the TaBx genes. The polymorphisms present both in the coding sequences and non-coding regions of ScBx in relation to other Bx genes are predicted to have an impact on the expression, structure and properties of the encoded proteins.

A Computational Model of the SC Multisensory Neurons: Integrative Capabilities, Maturation, and Plasticity

Directory of Open Access Journals (Sweden)

Cristiano Cuppini

2011-10-01

Full Text Available Different cortical and subcortical structures present neurons able to integrate stimuli of different sensory modalities. Among the others, one of the most investigated integrative regions is the Superior Colliculus (SC, a midbrain structure whose aim is to guide attentive behaviour and motor responses toward external events. Despite the large amount of experimental data in the literature, the neural mechanisms underlying the SC response are not completely understood. Moreover, recent data indicate that multisensory integration ability is the result of maturation after birth, depending on sensory experience. Mathematical models and computer simulations can be of value to investigate and clarify these phenomena. In the last few years, several models have been implemented to shed light on these mechanisms and to gain a deeper comprehension of the SC capabilities. Here, a neural network model (Cuppini et al., 2010 is extensively discussed. The model considers visual-auditory interaction, and is able to reproduce and explain the main physiological features of multisensory integration in SC neurons, and their acquisition during postnatal life. To reproduce a neonatal condition, the model assumes that during early life: 1 cortical-SC synapses are present but not active; 2 in this phase, responses are driven by non-cortical inputs with very large receptive fields (RFs and little spatial tuning; 3 a slight spatial preference for the visual inputs is present. Sensory experience is modeled by a “training phase” in which the network is repeatedly exposed to modality-specific and cross-modal stimuli at different locations. As results, Cortical-SC synapses are crafted during this period thanks to the Hebbian rules of potentiation and depression, RFs are reduced in size, and neurons exhibit integrative capabilities to cross-modal stimuli, such as multisensory enhancement, inverse effectiveness, and multisensory depression. The utility of the modelling

Crystal structure and magnetic properties of the solid-solution phase Ca3Co2-v Sc v O6

International Nuclear Information System (INIS)

Hervoches, Charles H.; Fredenborg, Vivian Miksch; Kjekshus, Arne; Fjellvag, Helmer; Hauback, Bjorn C.

2007-01-01

The two crystallographically non-equivalent Co atoms of the quasi-one-dimensional crystal structure of Ca 3 Co 2 O 6 form chains with alternating, face-sharing polyhedra of Co2O 6 trigonal prisms and Co1O 6 octahedra. This compound forms a substitutional solid-solution phase with Sc, in which the Sc atoms enter the Co2 sublattice exclusively. The homogeneity range of Ca 3 Co 2- v Sc v O 6 (more specifically Ca 3 Co1Co2 1- v Sc v O 6 ) extends up to v∼0.55. The crystal structure belongs to space group R3-barc with lattice parameters (in hexagonal setting): 9.0846(3)≤a≤9.1300(2) A and 10.3885(4)≤c≤10.4677(4) A. The magnetic moment decreases rapidly with increasing amount of the non-magnetic Sc solute in the lattice. - Graphical abstract: The quasi-one-dimensional Ca 3 Co 2 O 6 phase forms a substitutional solid-solution system with Sc, in which the Sc atoms enter the Co2 sublattice exclusively. The homogeneity range of Ca 3 Co 2- v Sc v O 6 extends up to v∼0.55. The magnetic moment decreases rapidly with increasing amount of the non-magnetic Sc solute in the lattice

TSE strain differentiation in mice by immunohistochemical PrP(Sc) profiles and triplex Western blot.

Science.gov (United States)

van Keulen, Lucien J M; Langeveld, Jan P M; Dolstra, Corry H; Jacobs, Jorg; Bossers, Alex; van Zijderveld, Fred G

2015-10-01

TSE strains are routinely identified by their incubation period and vacuolation profile in the brain after intracerebral inoculation and serial passaging in inbred mouse lines. There are some major drawbacks to this method that are related to the variation in vacuolation that exists in the brains of mice infected with the same TSE strain and to variation between observers and laboratories in scoring vacuolation and determining the final incubation period. We investigated the potential of PrP(Sc) immunohistochemistry and triplex Western blotting as possible alternative methods to differentiate between TSE strains. TSE reference strains ME7, 87A/87V, 22A/22C, 79A/79V and 301C/301V were intracerebrally inoculated in RIII or VM inbred mice that differ in their PrP genotype. Immunohistochemical PrP(Sc) profiles were drawn up by scanning light microscopy both on coronal and sagittal sections. On the basis of the localization of PrP(Sc) in the cerebral cortex, hippocampus, and cerebellar cortex and the overall type of PrP(Sc) staining, all TSE strains could be well differentiated from each other through their typical strain dependent characteristics. In addition, Western blot showed that the combination of glycosylation profile and 12B2 epitope content of PrP(Sc) allowed to distinguish between all reference strains except for ME7 and 22A in VM mice. TSE strains in mice can be identified on the basis of their PrP(Sc) profile alone. The potential to identify TSE strains in ruminants with these PrP(Sc) profiles after a single primary passage in mice will be the topic of future studies. © 2014 British Neuropathological Society.

Relapse outcomes, safety, and treatment patterns in patients diagnosed with relapsing-remitting multiple sclerosis and initiated on subcutaneous interferon β-1a or dimethyl fumarate: a real-world study.

Science.gov (United States)

Ernst, Frank R; Barr, Peri; Elmor, Riad; Wong, Schiffon L

2017-12-01

To estimate real-world treatment patterns, safety, and relapse outcomes of subcutaneous (sc) interferon (IFN) β-1a (Rebif) vs dimethyl fumarate (DMF; Tecfidera), to treat relapsing-remitting multiple sclerosis (RRMS). A US retrospective chart review of 450 randomly selected adults newly diagnosed with RRMS who received sc IFN β-1a (n = 143) or DMF (n = 307) was conducted. Patients were either (a) treatment-naïve, initiating first-line treatment with sc IFN β-1a or DMF, or (b) previously treated, switching to sc IFN β-1a or DMF. Two years' follow-up data were captured. Patient characteristics, persistence, and adverse events between treatment groups were compared using t-tests or Chi-square tests. Kaplan-Meier curves with log-rank tests and Cox proportional hazards models were used to compare time to, and risk of non-persistence. Annualized Relapse Rates (ARR) were calculated using a robust variance Poisson model adjusting for covariates. Propensity scores were used to address possible selection bias. One hundred and twelve patients became non-persistent, most commonly due to an adverse event (n = 37). No difference was observed in time to overall non-persistence between sc IFN β-1a and DMF patients. Among treatment-naïve patients, those receiving DMF had 2.4-times the risk (HR = 2.439, 95% CI = 1.007-5.917, p = .0483) of experiencing a discontinuation than patients receiving sc IFN β-1a. Non-persistent patients receiving DMF had 2.3-times the risk (HR = 2.311, 95% CI = 1.350-3.958, p = .0023) of experiencing an adverse event at a given time point than patients prescribed sc IFN β-1a. No differences in relapse risk or ARR between sc IFN β-1a- and DMF-treated patients were observed. sc IFN β-1a-treated patients had comparable persistence and relapse outcomes, and better safety outcomes vs DMF-treated patients across 2 years.

AlScN thin film based surface acoustic wave devices with enhanced microfluidic performance

International Nuclear Information System (INIS)

Wang, W B; Xuan, W P; Chen, J K; Wang, X Z; Luo, J K; Fu, Y Q; Chen, J J; Duan, P F; Mayrhofer, P; Bittner, A; Schmid, U

2016-01-01

This paper reports the characterization of scandium aluminum nitride (Al 1−xS c xN , x   =  27%) films and discusses surface acoustic wave (SAW) devices based on them. Both AlScN and AlN films were deposited on silicon by sputtering and possessed columnar microstructures with (0 0 0 2) crystal orientation. The AlScN/Si SAW devices showed improved electromechanical coupling coefficients ( K 2 , ∼2%) compared with pure AlN films (<0.5%). The performance of the two types of devices was also investigated and compared, using acoustofluidics as an example. The AlScN/Si SAW devices achieved much lower threshold powers for the acoustic streaming and pumping of liquid droplets, and the acoustic streaming and pumping velocities were 2  ×  and 3  ×  those of the AlN/Si SAW devices, respectively. Mechanical characterization showed that the Young’s modulus and hardness of the AlN film decreased significantly when Sc was doped, and this was responsible for the decreased acoustic velocity and resonant frequency, and the increased temperature coefficient of frequency, of the AlScN SAW devices. (paper)

Experimental Studies on the Interaction of scCO2 and scCO2-SO2 With Rock Forming Minerals at Conditions of Geologic Carbon Storages - First Results

Science.gov (United States)

Erzinger, J.; Wilke, F.; Wiersberg, T.; Vasquez Parra, M.

2010-12-01

Co-injection of SO2 (plus possibly NOx and O2) during CO2 storage in deep saline aquifers may cause stronger brine acidification than CO2 alone. Because of that, we investigate chemical corrosion of rocks and rock-forming minerals with impure supercritical CO2 (scCO2) at possible storage conditions of >73.7 bar and >31°C. Contaminates were chosen with respect to the composition of CO2 captured industrially from coal-fired power plants using the oxyfuel technology. The resulting data should build a base for the long-term prediction of the behavior of CO2 in geologic storage reservoirs. Experiments of up to 1000 hrs duration have been performed with 10 natural mineral concentrates (calcite, dolomite, siderite, anhydrite, hematite, albite, microcline, kaolinite, muscovite, biotite) in 3n NaCl solution and pure scCO2 or scCO2+SO2 (99.5+0.5 vol%). The NaCl reaction fluid resembles the average salinity of deep formation waters of the North German Basin and is not free of oxygen. To increase reaction rates all minerals were ground and the reagents agitated either by stirring or shaking in autoclaves of about one liter in volume. The autoclaves consist of Hastelloy™ or ferromagnetic stainless steel fully coated with PTFE. We used in average 15 g of solids, 700 ml liquid, and the vessels were pressurized up to 100 bars with CO2 or CO2-SO2 mixture. Experiments were run at temperatures up to 90°C. Before, during and after the experiments small amounts fluids were sampled and analyzed for dissolved constituents and pH. Solid phases were characterized by XRF, XRD, and EMPA before and after the experiments. Pure scCO2 corrodes all carbonates, reacts only slightly with anhydrite, albite, and microcline at a minimum pH of 4, and does not recognizably interact with the others. After the experiment, albite has gained in a, not yet fully identified, carbonate phase which might be dawsonite. Reaction fluids of the experiments with scCO2+SO2 have mostly lower pH than using scCO2

Characterization of Anti-Citrinin Specific ScFvs Selected from Non-Immunized Mouse Splenocytes by Eukaryotic Ribosome Display.

Directory of Open Access Journals (Sweden)

Haiwei Cheng

Full Text Available Single chain variable fragments (scFvs against citrinin (CIT were selected from a scFv library constructed from the splenocytes of non-immunized mice by an improved eukaryotic ribosome display technology in this study. Bovine serum albumin (BSA/ CIT-BSA and ovalbumin (OVA/ CIT-OVA were used as the antigens to select specific anti-CIT scFvs. Eukaryotic in situ RT-PCR method was used to recover the selected mRNA after every affinity selection. After six rounds of ribosome display, expression vector pTIG-TRX carrying specific scFv DNAs were constructed and transformed into Escherichia coli BL21 (DE3 for protein expression. Thirteen positive clones were selected out of which three (designated 23, 68 and 109 showed high binding activity and specificity to CIT by indirect ELISA, while no clone showed binding activity with carrier proteins. The three scFvs showed high specificity to CIT and the cross reactivity with other mycotoxins was below 0.01% as determined by indirect competitive ELISA. These specific scFvs offer a potential novel immunoassay method for CIT residues. This study confirmed the effectiveness of the improved eukaryotic ribosome display system and could be used as a reference for the selection of scFvs specific to other small molecules using ribosome display.

Recombinant norovirus-specific scFv inhibit virus-like particle binding to cellular ligands

Directory of Open Access Journals (Sweden)

Hardy Michele E

2008-01-01

Full Text Available Abstract Background Noroviruses cause epidemic outbreaks of gastrointestinal illness in all age-groups. The rapid onset and ease of person-to-person transmission suggest that inhibitors of the initial steps of virus binding to susceptible cells have value in limiting spread and outbreak persistence. We previously generated a monoclonal antibody (mAb 54.6 that blocks binding of recombinant norovirus-like particles (VLP to Caco-2 intestinal cells and inhibits VLP-mediated hemagglutination. In this study, we engineered the antigen binding domains of mAb 54.6 into a single chain variable fragment (scFv and tested whether these scFv could function as cell binding inhibitors, similar to the parent mAb. Results The scFv54.6 construct was engineered to encode the light (VL and heavy (VH variable domains of mAb 54.6 separated by a flexible peptide linker, and this recombinant protein was expressed in Pichia pastoris. Purified scFv54.6 recognized native VLPs by immunoblot, inhibited VLP-mediated hemagglutination, and blocked VLP binding to H carbohydrate antigen expressed on the surface of a CHO cell line stably transfected to express α 1,2-fucosyltransferase. Conclusion scFv54.6 retained the functional properties of the parent mAb with respect to inhibiting norovirus particle interactions with cells. With further engineering into a form deliverable to the gut mucosa, norovirus neutralizing antibodies represent a prophylactic strategy that would be valuable in outbreak settings.

DiSC aitab käitumist parandada / Ain Kivesti

Index Scriptorium Estoniae

Kivesti, Ain

2008-01-01

DiSC testi abil on võimalik saada ülevaade personaalsetest käitumishoiakutest ning vastavalt olukorrale on võimalik harjumuspärast reageerimisstiili radikaalselt muuta. Kommenteerivad Jorma Sarv ja Paavo Pilv

Cosmogenic 45Sc in Gibeon iron meteorite by radioanalytical neutron activation analysis

International Nuclear Information System (INIS)

Oura, Y.; Honda, M.; Ebihara, M.; Bajo, K.; Nagao, K.

2011-01-01

Cosmogenic nuclides in many fragments of Gibeon iron meteorite have been studied by Honda and coworkers. They observed that their concentrations varied by 5 orders and found that Gibeon gives two different exposure ages using pair of stable noble gas isotopes and radinuclide. To assess one possible cause for the difference, namely loss of partial noble gases due to atmospheric heating of the incoming meteoroid, concentrations of non-volatile and stable cosmogenic 45 Sc of Gibeon were determined by radiochemical neutron activation analysis (RNAA). For RNAA, a radiochemical procedure using extraction chromatography was developed to separate Sc from an iron meteorite. Concentrations of 45 Sc in 7 fragments ranged from 0.0064 to 0.11 ppb and correlated with cosmogenic 4 He concentrations. This correlation suggests that noble gases in Gibeon were not lost during the fall to the earth. (orig.)

76 FR 53353 - Proposed Amendment of Class E Airspace; Carroll, IA

Science.gov (United States)

2011-08-26

...-0845; Airspace Docket No. 11-ACE-19] Proposed Amendment of Class E Airspace; Carroll, IA AGENCY... action proposes to amend Class E airspace at Carroll, IA. Decommissioning of the Carroll non-directional beacon (NDB) at Arthur N. Neu Airport, Carroll, IA, has made this action necessary for the safety and...

75 FR 6595 - Proposed Amendment of Class E Airspace; Mapleton, IA

Science.gov (United States)

2010-02-10

...-1155; Airspace Docket No. 09-ACE-14] Proposed Amendment of Class E Airspace; Mapleton, IA AGENCY... action proposes to amend Class E airspace at Mapleton, IA. Additional controlled airspace is necessary to..., Mapleton, IA. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules...

76 FR 66870 - Proposed Amendment of Class E Airspace; Rugby, ND

Science.gov (United States)

2011-10-28

...-0433; Airspace Docket No. 11-AGL-12] Proposed Amendment of Class E Airspace; Rugby, ND AGENCY: Federal... proposes to amend Class E airspace at Rugby, ND. Decommissioning of the Rugby non-directional beacon (NDB) at Rugby Municipal Airport, Rugby, ND, has made this action necessary for the safety and management...

75 FR 43884 - Proposed Amendment of Class E Airspace; Searcy, AR

Science.gov (United States)

2010-07-27

...-1182; Airspace Docket No. 09-ASW-37] Proposed Amendment of Class E Airspace; Searcy, AR AGENCY: Federal... proposes to amend Class E airspace at Searcy, AR. Decommissioning of the Searcy non-directional beacon (NDB) at Searcy Municipal Airport, Searcy, AR, has made this action necessary for the safety and management...

Plutonium finishing plant safety systems and equipment list

International Nuclear Information System (INIS)

Bergquist, G.G.

1995-01-01

The Safety Equipment List (SEL) supports Analysis Report (FSAR), WHC-SD-CP-SAR-021 and the Plutonium Finishing Plant Operational Safety Requirements (OSRs), WHC-SD-CP-OSR-010. The SEL is a breakdown and classification of all Safety Class 1, 2, and 3 equipment, components, or system at the Plutonium Finishing Plant complex

Safety functions and component classification for BWR, PWR and PTR

International Nuclear Information System (INIS)

1979-01-01

The Safety Guide forms part of the IAEA programme, referred to as the NUSS programme (Nuclear Safety Standards), for establishing Codes of Practice and Safety Guides relating to thermal neutron power plants. The present Safety Guide has the following chapters: safety functions, ranking of safety functions, assignment of safety class requirements. Design requirements for structural integrity of boundaries of fluid-retaining components are also discussed

Software Quality Assurance for Nuclear Safety Systems

International Nuclear Information System (INIS)

Sparkman, D R; Lagdon, R

2004-01-01

-critical software and applies the highest level of rigor for those systems. DOE has further defined a risk approach to nuclear safety system software consistent with the analyses required for operation of nuclear facilities. This requires the grading of software in terms of safety class and safety significant structures, systems and components (SSCs). Safety-class SSCs are related to public safety where as safety-significant SSCs are identified for specific aspects of defense-in-depth and worker safety. Industry standards do not directly categorize nuclear safety software and DOE sites are not consistent in their approach to nuclear safety software quality assurance. DOE is establishing a more detailed graded approach for software associated with safety class and safety significant systems. This paper presents the process and results that DOE utilized to develop a detailed classification scheme for nuclear safety software

Electronic structure and physical properties of ScN in pressure: density-functional theory calculations

International Nuclear Information System (INIS)

Guan Pengfei; Wang Chongyu; Yu Tao

2008-01-01

Local density functional is investigated by using the full-potential linearized augmented plane wave (FP-LAPW) method for ScN in the hexagonal structure and the rocksalt structure and for hexagonal structures linking a layered hexagonal phase with wurtzite structure along a homogeneous strain transition path. It is found that the wurtzite ScN is unstable and the layered hexagonal phase, labelled as h o , in which atoms are approximately fivefold coordinated, is metastable, and the rocksalt ScN is stable. The electronic structure, the physical properties of the intermediate structures and the energy band structure along the transition are presented. It is found that the band gaps change from 4.0 to 1.0 eV continuously when c/a value varies from 1.68 to 1.26. It is noticeable that the study of ScN provides an opportunity to apply this kind of material (in wurtzite[h]-derived phase). (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Study on examples of safety culture enhancing activities at U.S. Nuclear Power Stations

International Nuclear Information System (INIS)

Ichiki, Kuniyasu

2010-01-01

After the wake of the incident of reactor vessel head degradation at Davis Basse in 2002, the NRC, the regulatory body in the U.S., included extraction of safety culture (SC) related elements from every failure into its inspection scheme of Reactor Oversight Process, since July 2006. The idea of SC itself was established some time ago, though, there are very few similar examples of such evaluation so far. This study is an attempt of making analyses on various activities with regard to SC in the U.S., to gain useful knowledge for considering the way to improve station's SC in Japan. Despite the fact that the numbers of inspection findings at stations are generally seen as unchanged, it is obvious that there are substantial difference in the number of the NRC's findings by each station. This appears to show that the condition of SC may largely different by stations. At several stations which accepted our investigation, those staff have made serious efforts to correct their area for improvements which were pointed out by the NRC. Such examples include improving management of their Corrective Action Program and establishing various measures to enable transmitting employee's concerns. It is thought that such activities aim to achieve efficient transfer of vital information among the station. This kind of activities should help every station solve various deficiencies in equipment, and also remove any obstacles in its communication. Their effort seem to result in not only the decrease in number of trouble but also much enhancement of mutual trust among the station, which would contribute to the great advance in their SC. (author)

Linking Gateway Technical College with Workforce Development: The SC Johnson-A Family Company Story.

Science.gov (United States)

Knudson, Edward

2004-01-01

Seven years ago, SC Johnson--A Family Company approached Gateway Technical College with a need to further strengthen their incumbent workforce's technical training and education. Retirements, brain drain, and competition for technical expertise were the forces driving SC Johnson to develop a comprehensive, flexible, and timely workplace education…

Production of a germline-humanized cetuximab scFv and evaluation of its activity in recognizing EGFR- overexpressing cancer cells.

Science.gov (United States)

Banisadr, Arsham; Safdari, Yaghoub; Kianmehr, Anvarsadat; Pourafshar, Mahdieh

2018-04-03

The aim of this study was to produce a humanized single chain antibody (scFv) as a potential improved product design to target EGFR (Epidermal Growth Factor Receptor) overexpressing cancer cells. To this end, CDR loops of cetuximab (an FDA-approved anti-EGFR antibody) were grafted on framework regions derived from type 3 (VH3 and VL3 kappa) human germline sequences to obtain recombinant VH and VL domainslinked together with a flexible linker [(Gly 4 Ser) 3 ] to form a scFv. Codon optimized synthetic gene encoding the scFv (with NH2-VH-linker-VL-COOH orientation) was expressed in E. coli Origami™ 2(DE3) cells and the resultant scFv purified by using Ni-NTA affinity chromatography. The scFv, called cet.Hum scFv, was evaluated in ELISA and immunoblot to determine whether it can recognize EGFR. The scFv was able to recognize EGFR over-expressing cancer cells (A-431) but failed to detect cancer cells with low levels of EGFR (MCF-7 cells). Although the affinity of the scFv forA-431 cells was 9 fold lower than that of cetuximab, it was strong enough to recognize these cells. Considering its ability to bind EGFR molecules, the scFv may exhibit a potential application for the detection of EGFR-overexpressing cancer cells.

World class manufacturing in metallurgical enterprise

Directory of Open Access Journals (Sweden)

B. Gajdzik

2013-01-01

Full Text Available World Class Manufacturing (WCM assumes increase of efficiency of the company by elimination of all the losses, wastage and dangers of safety. In ArcelorMittal the concept of WCM is implemented in particular enterprises within the capital group. In this publication the activities conducted in some of those enterprises are described.

K West integrated water treatment system subproject safety analysis document

International Nuclear Information System (INIS)

SEMMENS, L.S.

1999-01-01

This Accident Analysis evaluates unmitigated accident scenarios, and identifies Safety Significant and Safety Class structures, systems, and components for the K West Integrated Water Treatment System

K West integrated water treatment system subproject safety analysis document

Energy Technology Data Exchange (ETDEWEB)

SEMMENS, L.S.

1999-02-24

This Accident Analysis evaluates unmitigated accident scenarios, and identifies Safety Significant and Safety Class structures, systems, and components for the K West Integrated Water Treatment System.

Evaluation of the first 44Sc-labeled Affibody molecule for imaging of HER2-expressing tumors

International Nuclear Information System (INIS)

Honarvar, Hadis; Müller, Cristina; Cohrs, Susan; Haller, Stephanie; Westerlund, Kristina; Karlström, Amelie Eriksson; Meulen, Nicholas P. van der; Schibli, Roger; Tolmachev, Vladimir

2017-01-01

Introduction: Affibody molecules are small (58 amino acids) high-affinity proteins based on a tri-helix non-immunoglobulin scaffold. A clinical study has demonstrated that PET imaging using Affibody molecules labeled with 68 Ga (T ½ = 68 min) can visualize metastases of breast cancer expressing human epidermal growth factor receptor type 2 (HER2) and provide discrimination between tumors with high and low expression level. This may help to identify breast cancer patients benefiting from HER2-targeting therapies. The best discrimination was at 4 h post injection. Due to longer half-life, a positron-emitting radionuclide 44 Sc (T ½ = 4.04 h) might be a preferable label for Affibody molecules for imaging at several hours after injection. Methods: A synthetic second-generation anti-HER2 Affibody molecule Z HER2:2891 was labeled with 44 Sc via a DOTA-chelator conjugated to the N-terminal amino group. Binding specificity, affinity and cellular processing 44 Sc-DOTA-Z HER2:2891 and 68 Ga-DOTA-Z HER2:2891 were compared in vitro using HER2-expressing cells. Biodistribution and imaging properties of 44 Sc-DOTA-Z HER2:2891 and 68 Ga-DOTA-Z HER2:2891 were evaluated in Balb/c nude mice bearing HER2-expression xenografts. Results: The labeling yield of 98 ± 2% and specific activity of 7.8 GBq/μmol were obtained. The conjugate demonstrated specific binding to HER2-expressing SKOV3.ip cells in vitro and to SKOV3.ip xenografts in nude mice. The distribution of radioactivity at 3 h post injection was similar for 44 Sc-DOTA-Z HER2:2891 and 68 Ga-DOTA-Z HER2:2891 , but the blood clearance of the 44 Sc-labeled variant was slower and the tumor-to-blood ratio was reduced (15 ± 2 for 44 Sc-DOTA-Z HER2:2891 vs 46 ± 9 for 68 Ga-DOTA-Z HER2:2891 ). At 6 h after injection of 44 Sc-DOTA-Z HER2:2891 the tumor uptake was 8 ± 2% IA/g and the tumor-to-blood ratio was 51 ± 8. Imaging using small-animal PET/CT demonstrated that 44 Sc-DOTA-Z HER2:2891 provides specific and high

Quaternary borocarbides: New class of intermetallic superconductors

Science.gov (United States)

Nagarajan, R.; Gupta, L. C.; Dhar, S. K.; Mazumdar, Chandan; Hossain, Zakir; Godart, C.; Levy-Clement, C.; Padalia, B. D.; Vijayaraghavan, R.

1995-01-01

Our recent discovery of superconductivity (SC) in the four-element multiphase Y-Ni-B-C system at an elevated temperature (TC approximately 12 K) has opened up great possibilities of identifying new superconducting materials and generating new physics. Superconductivity with Tc (greater than 20 K) higher than that known so far in bulk intermetallics has been observed in multiphase Y-Pd-B-C and Th-Pd-B-C systems and a family of single phase materials RENi2B2C (RE= Y, rare earth) have been found. Our investigations show YNi2B2C to be a strong coupling hard type-II SC. HC2(T) exhibits an unconventional temperature dependence. Specific heat and magnetization studies reveal coexistence of SC and magnetism in RNi2B2C (R = Ho, Er, Tm) with magnetic ordering temperatures (Tc approximately 8 K, 10.5 K, 11 K and Tm approximately 5 K, approximately 7K, approximately 4 K respectively) that are remarkably higher than those in known magnetic superconductors . Mu-SR studies suggest the possibility of Ni atoms carrying a moment in TmNi2B2C. Resistivity results suggests a double re-entrant transition (SC-normal-SC) in HoNi2B2C. RENi2B2C (RE = Ce, Nd, Gd) do not show SC down to 4.2 K. The Nd- and Gd-compounds order magnetically at approximately 4.5 K and approximately 19.5 K, respectively. Two SC transitions are observed in Y-Pd-B-C (Tc approximately 22 K, approximately 10 K) and in Th-Pd-B-C (Tc approximately 20 K, approximately 14 K) systems, which indicate that there are at least two structures which support SC in these borocarbides. In our multiphase ThNi2B2C we observe SC at approximately 6 K. No SC was seen in multiphase UNi2B2C, UPd2B2C, UOs2Ge2C and UPd5B3C(0.35) down to 4.2 K. Tc in YNi2B2C is depressed by substitutions (Gd, Th and U at Y-sites and Fe, Co at Ni-sites).

Plutonium Finishing Plant (PFP) HVAC System Component Index; FINAL

International Nuclear Information System (INIS)

DICK, J.D.

1999-01-01

This document identities the components, design media, procedures and defines the critical characteristics of Commercial Grade Items necessary to ensure the HVAC system provides these functions. This document lists safety class (SC) and safety significant (SS) components for the Heating Ventilation Air Conditioning (HVAC) and specifies the critical characteristics for Commercial Grade Items (CGI), as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics for any one item

M.Sc. in Civil and Structural Engineering

DEFF Research Database (Denmark)

The following pages contain a list of project ideas proposed by the scientific staff at the Department of Civil Engineering, Aalborg University, and a number of companies. Most of the project ideas in this catalogue may form the basis for long and short master projects as well as regular 3rd...... semester projects at the M.Sc. programme in Civil and Structural Engineering....

M.Sc. in Civil and Structural Engineering

DEFF Research Database (Denmark)

Clausen, Johan

The report contain a list of project ideas proposed by the scientific staff at the Department of Civil Engineering, Aalborg University, and a number of companies. Most of the project ideas in this catalogue may form the basis for long and short candidate projects as well as regular 3rd semester...... projects at the M.Sc. programme in Civil and Structural Engineering....

M.Sc. in Civil and Structural Engineering

DEFF Research Database (Denmark)

The catalogue contain a list of project ideas proposed by the scientific staff at the Department of Civil Engineering, Aalborg University, and a number of companies. Most of the project ideas in this catalogue may form the basis for long and short candidate projects as well as regular 3rd semester...... projects at the M.Sc. programme in Civil and Structural Engineering....

M.Sc. in Civil and Structural Engineering

DEFF Research Database (Denmark)

This catalogue contains a list of project ideas proposed by the scientific staff at the Department of Civil Engineering, Aalborg University, and a number of companies. Most of the project ideas in this catalogue may form the basis for long and short candidate projects as well as regular 3rd...... semester projects at the M.Sc. programme in Civil and Structural Engineering....

Solution Synthesis, Structure, and CO2 Reduction Reactivity of a Scandium(II) Complex, {Sc[N(SiMe3 )2 ]3 }.

Science.gov (United States)

Woen, David H; Chen, Guo P; Ziller, Joseph W; Boyle, Timothy J; Furche, Filipp; Evans, William J

2017-02-13

The first crystallographically characterizable complex of Sc 2+ , [Sc(NR 2 ) 3 ] - (R=SiMe 3 ), has been obtained by LnA 3 /M reactions (Ln=rare earth metal; A=anionic ligand; M=alkali metal) involving reduction of Sc(NR 2 ) 3 with K in the presence of 2.2.2-cryptand (crypt) and 18-crown-6 (18-c-6) and with Cs in the presence of crypt. Dark maroon [K(crypt)] + , [K(18-c-6)] + , and [Cs(crypt)] + salts of the [Sc(NR 2 ) 3 ] - anion are formed, respectively. The formation of this oxidation state of Sc is also indicated by the eight-line EPR spectra arising from the I=7/2 45 Sc nucleus. The Sc(NR 2 ) 3 reduction differs from Ln(NR 2 ) 3 reactions (Ln=Y and lanthanides) in that it occurs under N 2 without formation of isolable reduced dinitrogen species. [K(18-c-6)][Sc(NR 2 ) 3 ] reacts with CO 2 to produce an oxalate complex, {K 2 (18-c-6) 3 }{[(R 2 N) 3 Sc] 2 (μ-C 2 O 4 -κ 1 O:κ 1 O'')}, and a CO 2 - radical anion complex, [(R 2 N) 3 Sc(μ-OCO-κ 1 O:κ 1 O')K(18-c-6)] n . © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

First-in-Human PET/CT Imaging of Metastatic Neuroendocrine Neoplasms with Cyclotron-Produced 44Sc-DOTATOC: A Proof-of-Concept Study.

Science.gov (United States)

Singh, Aviral; van der Meulen, Nicholas P; Müller, Cristina; Klette, Ingo; Kulkarni, Harshad R; Türler, Andreas; Schibli, Roger; Baum, Richard P

2017-05-01

44 Sc is a promising positron emission tomography (PET) radionuclide (T 1/2  = 4.04 hours, E β+average  = 632 keV) and can be made available, using a cyclotron production route, in substantial quantities as a highly pure product. Herein, the authors report on a first-in-human PET/CT study using 44 Sc-DOTATOC prepared with cyclotron-produced 44 Sc. The production of 44 Sc was carried out through the 44 Ca(p,n) 44 Sc nuclear reaction at Paul Scherrer Institut, Switzerland. After separation, 44 Sc was shipped to Zentralklinik Bad Berka, Germany, where radiolabeling was performed, yielding radiochemically pure 44 Sc-DOTATOC. Two patients, currently followed up after peptide receptor radionuclide therapy of metastatic neuroendocrine neoplasms, participated in this proof-of-concept study. Blood sampling was performed before and after application of 44 Sc-DOTATOC. PET/CT acquisitions, performed at different time points after injection of 44 Sc-DOTATOC, allowed detection of even very small lesions on delayed scans. No clinical adverse effects were observed and the laboratory hematological, renal, and hepatic profiles remained unchanged. In this study, cyclotron-produced 44 Sc was used in the clinic for the first time. It is attractive for theranostic application with 177 Lu, 90 Y, or 47 Sc as therapeutic counterparts. 44 Sc-based radiopharmaceuticals will be of particular value for PET facilities without radiopharmacy, to which they can be shipped from a centralized production site.

AAZTA: an ideal chelating agent for the development of {sup 44}Sc PET imaging agents

Energy Technology Data Exchange (ETDEWEB)

Nagy, Gabor; Szikra, Dezso; Trencsenyi, Gyoergy [Scanomed Ltd., Debrecen (Hungary); University of Debrecen, Medical Imaging Clinic (Hungary); Fekete, Aniko [University of Debrecen, Medical Imaging Clinic (Hungary); Garai, Ildiko [Scanomed Ltd., Debrecen (Hungary); Giani, Arianna M.; Negri, Roberto [Dipartimento di Scienze del Farmaco, Universita del Piemonte Orientale, Novara (Italy); Masciocchi, Norberto [Dipartimento di Scienza e Alta Tecnologia e To.Sca.Lab, Universita degli Studi dell' Insubria, Como (Italy); Maiocchi, Alessandro; Uggeri, Fulvio [Bracco Imaging spa, Bracco Research Centre, Colleretto Giacosa (Italy); Toth, Imre [Department of Inorganic and Analytical Chemistry, University of Debrecen (Hungary); Aime, Silvio [Dipartimento di Biotecnologie Molecolari e Scienze della Salute, Centro di Imaging Molecolare e Preclinico, Universita degli Studi di Torino (Italy); Giovenzana, Giovanni B. [Dipartimento di Scienze del Farmaco, Universita del Piemonte Orientale, Novara (Italy); CAGE Chemicals srl, Novara (Italy); Baranyai, Zsolt [Bracco Imaging spa, Bracco Research Centre, Colleretto Giacosa (Italy); Department of Inorganic and Analytical Chemistry, University of Debrecen (Hungary)

2017-02-13

Unprecedented fast and efficient complexation of Sc{sup III} was demonstrated with the chelating agent AAZTA (AAZTA=1,4-bis(carboxymethyl)-6-[bis(carboxymethyl)] amino-6-methylperhydro-1,4-d iazepine) under mild experimental conditions. The robustness of the {sup 44}Sc(AAZTA){sup -} chelate and conjugated biomolecules thereof is further shown by in vivo PET imaging in healthy and tumor mice models. The new results pave the way towards development of efficient Sc-based radiopharmaceuticals using the AAZTA chelator. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Calibration of the 46Sc sand tracer detector and it's application

International Nuclear Information System (INIS)

Li Zhangsu; Du Xiaoyun

1993-01-01

The authors describe the process and result for the calibration of radioactive 46 Sc detector in details. The calibration was carried out under the hydrological conditions similar to the field test. The relation between the intensity of the scattered γ-rays and the various water depths was studied by using a 46 Sc plane source. The purpose of calibration of the detector with the plane source is to determine both the detector sensitivity factor and the γ-ray absorption coefficient for san/water mixture in order to calculate the thickness of the mobile water layer by means of the count rate balance method. The relation curve between the various thicknesses of the mobile layers and count rates was studied in detailed in details by using a slab source and the uniformly mixed layers with 46 Sc glass. The curve is used as the calibration curve for determining the recovery of tracking radioactive tracer in situ. The recovery of tracer shows whether the field tracer data can be used to calculate the transport sediment rate or the in fill rate of sediment

PEGylation of polylysine dendrimers improves absorption and lymphatic targeting following SC administration in rats.

Science.gov (United States)

Kaminskas, Lisa M; Kota, Jagannath; McLeod, Victoria M; Kelly, Brian D; Karellas, Peter; Porter, Christopher Jh

2009-12-03

Polylysine dendrimers have potential as highly flexible, biodegradable nanoparticular carriers that may also promote lymphatic transport. The current study was undertaken to determine the impact of PEGylation on the absorption and lymphatic transport of polylysine dendrimers modified by surface derivatisation with PEG (200, 570 or 2000Da) or 4-benzene sulphonate following SC or IV dosing. PEGylation led to the PEG(200) derived dendrimer being rapidly and completely absorbed into the blood after SC administration, however only 3% of the administered dose was recovered in pooled thoracic lymph over 30h. Increasing the PEG chain length led to a systematic decrease in absorption into the blood and an enhancement of the proportion recovered in the lymphatics (up to 29% over 30h). For the PEG(570) and PEG(2000) derived dendrimers, indirect access to the lymph via equilibration across the capillary beds also appeared to play a role in lymphatic targeting after both IV and SC dosing. In contrast, the anionic benzene sulphonate-capped dendrimer was not well absorbed from the SC injection site (26% bioavailability) into either the blood or the lymph. The data suggest that PEGylated poly-L-lysine dendrimers are well absorbed from SC injection sites and that the extent of lymphatic transport may be enhanced by increasing the size of the PEGylated dendrimer complex.