Safe Transport of Radioactive Material, International Regulations and its Supporting Documents

Energy Technology Data Exchange (ETDEWEB)

El-Shinawy, R M.K. [Radiation Protection Dept., NRC, Atomic Energy Authority, Cairo (Egypt)

2005-04-01

Safe transport of radioactive material regulations issued by IAEA since 1961, provide standards for insuring a high level of safety of people,transport workers, property and environment against radiation, contamination and criticality hazards as well as thermal effects associated with the transport of the radioactive wastes and material. The history ,development, philosophy and scope of these international regulations were mentioned as well as the different supporting documents to the regulations for safe transport of radioactive material were identified.The first supporting document , namely TS - G-1.1 ( ST-2) ,Advisory material is also issued by the IAEA.It contains both the advisory and explanatory materials previously published in safety series No 7 and 37 and therefore TS-G-1.1 (ST-2) will supersede safety series No 7 and 37. The second supporting document namely TS-G-1.2 (ST-3), planning and preparing for emergency response to transport accidents involving radioactive material ,which will supersede safety series No 87. In addition to quality assurance (SS=113), compliance assurance (SS=112), the training manual and other.

Hysteresis effects on the high-temperature internal friction of polycrystalline zirconium

International Nuclear Information System (INIS)

Povolo, F.; Molinas, B.J.; Rosario Univ. Nacional

1985-01-01

Hysteresis effects present on the high temperature internal friction of annealed polycrystalline zirconium are investigated in detail. It is shown that two internal friction maxima are present when the measurements are performed on heating. If a high enough temperature is reached, only one internal friction maximum is observed on cooling. Furthermore, when the temperature is not decreased below a certain value (critical temperature) only the lower temperature peak is present during a subsequent heating cycle. The critical temperature is strongly dependent on the grain size. Finally, both the hysteresis effects and the internal friction maxima are explained by relaxation mechanisms associated with grain boundary sliding and segregation of impurities to the grain boundaries. (author)

FAST and SAFE Passive Safety Devices for Sodium-cooled Fast Reactor

Energy Technology Data Exchange (ETDEWEB)

Hartanto, Donny; Kim, Chihyung; Kim, In-Hyung; Kim, Yonghee [KAIST, Daejeon (Korea, Republic of)

2015-05-15

The major factor is the impact of the neutron spectral hardening. The second factor that affects the CVR is reduced capture by the coolant when the coolant voiding occurs. To improve the CVR, many ideas and concepts have been proposed, which include introduction of an internal blanket, spectrum softening, or increasing the neutron leakage. These ideas may reduce the CVR, but they deteriorate the neutron economy. Another potential solution is to adopt a passive safety injection device such as the ARC (autonomous reactivity control) system, which is still under development. In this paper, two new concepts of passive safety devices are proposed. The devices are called FAST (Floating Absorber for Safety at Transient) and SAFE (Static Absorber Feedback Equipment). Their purpose is to enhance the negative reactivity feedback originating from the coolant in fast reactors. SAFE is derived to balance the positive reactivity feedback due to sodium coolant temperature increases. It has been demonstrated that SAFE allows a low-leakage SFR to achieve a self-shutdown and self-controllability even though the generic coolant temperature coefficient is quite positive and the coolant void reactivity can be largely managed by the new FAST device. It is concluded that both FAST and SAFE devices will improve substantially the fast reactor safety and they deserve more detailed investigations.

High temperature internal friction in α-zirconium

International Nuclear Information System (INIS)

Ritchie, I.G.; Sprungman, K.W.

1981-03-01

The high temperature internal friction spectrum of α-Zr is resolved into five peaks, P 0 to P 4 , in addition to a background, B, that increases exponentially with the temperature. P 0 is attributed to the thermally assisted unpinning of dislocations from oxygen interstitial pinning points. P 1 is caused by the longitudinal redistribution of the same pinning points in the dislocation core, while P 2 is caused by the transverse core diffusion of these pinning points. Both P 0 and P 1 give rise to characteristic peaks of internal friction as a function of strain amplitude. The ratio of the modulus defect to the internal friction at the peak position is 0.5 in the case of unpinning, and significantly greater than 0.5 in the case of longitudinal core diffusion. A behavioural phase diagram or map is constructed to interpret the complex non-linear behaviour occurring in the temperature-strain amplitude plane in the regions where P 0 , P 1 and P 2 overlap. (author)

Rapid self-heating and internal temperature sensing of lithium-ion batteries at low temperatures

International Nuclear Information System (INIS)

Zhang, Guangsheng; Ge, Shanhai; Xu, Terrence; Yang, Xiao-Guang; Tian, Hua; Wang, Chao-Yang

2016-01-01

Highlights: • Self-heating lithium-ion battery (SHLB) structure provided a practical solution to the poor performance at subzero temperatures. • We report an improved SHLB that heats from −20 °C to 0 °C in 12.5 seconds, or 56% more rapidly, while consuming 24% less energy than previously reported. • The nickel foil heating element embedded inside a SHLB cell plays a dominant role in rapid self-heating. • The embedded nickel foil can simultaneously perform as an internal temperature sensor (ITS). • 2-sheet design self-heats faster than 1-sheet design due to more uniform internal temperature distribution. - Abstract: The recently discovered self-heating lithium-ion battery structure provided a practical solution to the poor performance at subzero temperatures that has hampered battery technology for decades. Here we report an improved self-heating lithium-ion battery (SHLB) that heats from −20 °C to 0 °C in 12.5 seconds, or 56% more rapidly, while consuming 24% less energy than that reported previously. We reveal that a nickel foil heating element embedded inside a SHLB cell plays a dominant role in self-heating and we experimentally demonstrate that a 2-sheet design can achieve dramatically accelerated self-heating due to more uniform internal temperature distribution. We also report, for the first time, that this embedded nickel foil can simultaneously perform as an internal temperature sensor (ITS) due to the perfectly linear relationship between the foil’s electrical resistance and temperature.

A new challenges in international cooperation. Via interdisciplinary approach towards safe nuclear industry back-end

International Nuclear Information System (INIS)

Dreimanis, Andrejs

2011-01-01

Development of multinational radioactive waste and spent nuclear fuel repositories requires safe nuclear industry back-end. We propose an interdisciplinary synergetic approach to multilevel consensus building for siting shared multinational repositories, based on self-organization, chaos and fuzziness concepts. An entire partnering country is considered as a higher-level stakeholder - the national stakeholder, being faced to simultaneous seeking an upward (international) and a downward (intra-national) consensus in the environment, being characterized by diverse political, economic and social interests. There is deduced: a) building of international stakeholder consensus could be promoted by activating the international scale multilateral interactions between intra- and international stakeholders, b) gradual progress in intergovernmental consensus and reaching multilateral agreements - the result of dialogue, via observing the whole set of various interests and common resolving of emerged controversies, and c) knowledge, mental flexibility and systems thinking - basic prerogatives for elevating the level of mutual understanding and consensus. (author)

Ensuring safe international trade: how are the roles and responsibilities evolving and what will the situation be in ten years' time?

Science.gov (United States)

Brückner, G K

2011-04-01

The roles of the international standard-setting bodies that are mandated to facilitate safe trade, such as the World Organisation for Animal Health (OIE), the Codex Alimentarius Commission, the International Plant Protection Convention and the World Trade Organization, are well documented, as are the roles of the international organisations responsible for global health issues: the OIE, the World Health Organization and the Food and Agriculture Organization of the United Nations. However, developments in international trade, such as accelerating globalisation and the frequent emergence and re-emergence of diseases affecting both humans and animals, have brought new challenges and the need to reconsider the future roles of such organisations. New participants and new demands have also emerged to challenge these mandates, leading to potential areas of conflict. The need for countries to establish themselves as new trade partners, or to strengthen their positions while still maintaining safe trade, poses a challenge to standard-setting organisations, which must meet these demands while still remaining sensitive to the needs of developing countries. In this paper, the author describes and discusses some of these challenges and suggests how international organisations could evolve to confront such issues.

Measuring the internal temperature of a levitated nanoparticle in high vacuum

Science.gov (United States)

Hebestreit, Erik; Reimann, René; Frimmer, Martin; Novotny, Lukas

2018-04-01

The interaction of an object with its surrounding bath can lead to a coupling between the object's internal degrees of freedom and its center-of-mass motion. This coupling is especially important for nanomechanical oscillators, which are among the most promising systems for preparing macroscopic objects in quantum mechanical states. Here we exploit this coupling to derive the internal temperature of a levitated nanoparticle from measurements of its center-of-mass dynamics. For a laser-trapped silica particle in high vacuum, we find an internal temperature of 1000 (60 )K . The measurement and control of the internal temperature of nanomechanical oscillators is of fundamental importance because black-body emission sets limits to the coherence of macroscopic quantum states.

Plutonium safe handling

International Nuclear Information System (INIS)

Tvehlov, Yu.

2000-01-01

The abstract, prepared on the basis of materials of the IAEA new leadership on the plutonium safe handling and its storage (the publication no. 9 in the Safety Reports Series), aimed at presenting internationally acknowledged criteria on the radiation danger evaluation and summarizing the experience in the safe management of great quantities of plutonium, accumulated in the nuclear states, is presented. The data on the weapon-class and civil plutonium, the degree of its danger, the measures for provision of its safety, including the data on accident radiation consequences with the fission number 10 18 , are presented. The recommendations, making it possible to eliminate the super- criticality danger, as well as ignition and explosion, to maintain the tightness of the facility, aimed at excluding the radioactive contamination and the possibility of internal irradiation, to provide for the plutonium security, physical protection and to reduce irradiation are given [ru

12th International Workshop on Low Temperature Electronics

International Nuclear Information System (INIS)

2017-01-01

The present volume of the Journal of Physics: Conference Series represents contributions from participants of the 12th International Workshop on Low Temperature Electronics held in Tempe, Arizona, USA from September 18-21, 2016. The conference was organized by the School of Earth and Space Exploration at Arizona State University.The International Workshop on Low Temperature Electronics (WOLTE) is a biennial conference devoted to the presentation and exchange of the most recent advances in the field of low temperature electronics and its applications. This international forum is open to everyone in the field.The technical program included oral presentations and posters on fundamental properties of cryogenic materials, cryogenic transistors, quantum devices and systems, astronomy and physics instrumentation, and fabrication of cryogenic devices. More than 50 scientists and engineers from various academic, government, and industrial institutions in Europe, Asia, and the Americas attended the conference.We would like to thank all speakers for their presentations and all attendees for their participation. We would also like to express our sincerest gratitude to our sponsors: Lake Shore Cryotronics, ASU NewSpace, ASU School of Earth and Space Exploration, and IRA A. Fulton Schools of Engineering for making this conference possible. (paper)

Online Internal Temperature Estimation for Lithium-Ion Batteries Based on Kalman Filter

OpenAIRE

Jinlei Sun; Guo Wei; Lei Pei; Rengui Lu; Kai Song; Chao Wu; Chunbo Zhu

2015-01-01

The battery internal temperature estimation is important for the thermal safety in applications, because the internal temperature is hard to measure directly. In this work, an online internal temperature estimation method based on a simplified thermal model using a Kalman filter is proposed. As an improvement, the influences of entropy change and overpotential on heat generation are analyzed quantitatively. The model parameters are identified through a current pulse test. The charge/discharg...

Online Internal Temperature Estimation for Lithium-Ion Batteries Based on Kalman Filter

Directory of Open Access Journals (Sweden)

Jinlei Sun

2015-05-01

Full Text Available The battery internal temperature estimation is important for the thermal safety in applications, because the internal temperature is hard to measure directly. In this work, an online internal temperature estimation method based on a simplified thermal model using a Kalman filter is proposed. As an improvement, the influences of entropy change and overpotential on heat generation are analyzed quantitatively. The model parameters are identified through a current pulse test. The charge/discharge experiments under different current rates are carried out on the same battery to verify the estimation results. The internal and surface temperatures are measured with thermocouples for result validation and model construction. The accuracy of the estimated result is validated with a maximum estimation error of around 1 K.

On the problem of safe usage of 12MKh steel at elevated temperatures and high hydrogen pressures

International Nuclear Information System (INIS)

Archakov, Yu.I.; Teslya, B.M.

1982-01-01

The behaviour of the 12MKh steel in hydrogen at pressures of 4-100 MPa and temperatures of 450-600 deg C has been investigated to study the regularities of hydrogen corrosion process. The samples are held in hydrogen under all-round compression in autoclaves with subsequent determination of mechanical properties, carbon content and microstructure. Dependencies of time to begining of intensive embrittlement under given conditions are found. The empiric equation for the calculation of time to beginning of hydrogen corrosion is derived, the safe usage of the 12MKh steel at different temperatures and pressures are determined

Predicting the diversity of internal temperatures from the English residential sector using panel methods

International Nuclear Information System (INIS)

Kelly, Scott; Shipworth, Michelle; Shipworth, David; Gentry, Michael; Wright, Andrew; Pollitt, Michael; Crawford-Brown, Doug; Lomas, Kevin

2013-01-01

Highlights: ► A new method is proposed incorporating behavioural, environmental and building efficiency variables to explain internal dwelling temperatures. ► It is the first time panel methods have been used to predict internal dwelling temperatures over time. ► The proposed method is able to explain 45% of the variance of internal temperature between heterogeneous dwellings. ► Results support qualitative research on the importance of social, cultural and psychological behaviour in determining internal dwelling temperatures. behaviour. ► This method presents new opportunities to quantify the size of the direct rebound effect between heterogeneous dwellings. -- Abstract: In this paper, panel methods are applied in new and innovative ways to predict daily mean internal temperature demand across a heterogeneous domestic building stock over time. This research not only exploits a rich new dataset but presents new methodological insights and offers important linkages for connecting bottom-up building stock models to human behaviour. It represents the first time a panel model has been used to estimate the dynamics of internal temperature demand from the natural daily fluctuations of external temperature combined with important behavioural, socio-demographic and building efficiency variables. The model is able to predict internal temperatures across a heterogeneous building stock to within ∼0.71 °C at 95% confidence and explain 45% of the variance of internal temperature between dwellings. The model confirms hypothesis from sociology and psychology that habitual behaviours are important drivers of home energy consumption. In addition, the model offers the possibility to quantify take-back (direct rebound effect) owing to increased internal temperatures from the installation of energy efficiency measures. The presence of thermostats or thermostatic radiator valves (TRVs) are shown to reduce average internal temperatures, however, the use of an automatic timer

Safe affordable fission engine (SAFE 30) module conductivity test thermal model correlation

International Nuclear Information System (INIS)

Roman, Jose

2001-01-01

The SAFE 30 is a simple, robust space fission power system that is comprised of several independent modules. Each module contains 4 fuel tubes bonded to a central heatpipe. Fission energy is conducted from the fuel tubes to the heatpipe, which in turn transfers the energy to a power conversion system. This paper benchmarks a thermal model of the SAFE 30 with actual test data from simulated SAFE 30 module tests. Two 'dummy' SAFE 30 modules were fabricated - each consisted of 4 1-inch dia. tubes (simulating the fuel tubes) bonded to a central '1' dia. tube (simulating the heatpipe). In the first module the fuel tubes were simply brazed to the heatpipe along the line of contact (leaving void space in the interstices), and in the second module the tubes and heatpipe were brazed via tri-cusps that completely fill the interstices between the tubes. In these tests, fission energy is simulated by placing resistance heaters within each of the 4 fuel tubes. The tests were conducted in a vacuum chamber in 4 configurations: tri-cusps filled with and without an outer insulation wrap, and no tri-cusps with and without an outer insulation wrap. The baseline SAFE 30 configuration uses the brazed tri-cusps. During the tests, the power applied to the heaters was varied in a stepwise fashion, until a steady-state temperature profile was reached. These temperature levels varied between 773 K and 1073 K. To benchmark the thermal model, the input energy and chamber surface temperature were used as boundary conditions for the model. The analytical results from the nodes at the same location as the test thermocouples were plotted again test data to determinate the accuracy of the analysis. The unknown variables on the analysis are the radiation emissivity of the pipe and chamber and the radiation view factor between the module and the chamber. A correlation was determined using a parametric analysis by varying the surface emissivity and view factor until a good match was reached. This

Internal modes in high-temperature plasmas

International Nuclear Information System (INIS)

Crew, G.B.

1983-02-01

The linear stability of current-carrying toroidal plamsas is examined to determine the possibility of exciting global internal modes. The ideal magnetohydrodynamic (MHD) theory provides a useful framework for the analysis of these modes, which involve a kinking of the central portion of the plasma column. Non-ideal effects can also be important, and these are treated for high-temperature regimes where the plasma is collisionless

International conference on lessons learned from the decommissioning of nuclear facilities and the safe termination of nuclear activities. Contributed papers

International Nuclear Information System (INIS)

2006-12-01

The International Atomic Energy Agency (IAEA), in cooperation with the European Commission (EC), Nuclear Energy Agency to the Organisation for Economic Co-operation and Development (OECD/NEA), and the World Nuclear Association (WNA), organized an International Conference on Lessons Learned from the Decommissioning of Nuclear Facilities and the Safe Termination of Nuclear Activities from 11 to 15 December 2006 in Athens, Greece. This Book of Contributed Papers contains technical papers and posters contributed by experts from operating organisations, regulatory bodies, technical support organisations, and other institutions on issues falling within the scope of the Conference. The following main topics were covered: Evolution of national and international policies and criteria for the safe and efficient decommissioning of nuclear facilities and safe termination of nuclear activities; Review of lessons learned from ongoing or completed activities associated with decommissioning; Improvement of safety and efficiency through the use of new and innovative technologies; Practical aspects in the management of material, waste and sites resulting from decommissioning, including the management of waste in the absence of repositories and waste acceptance requirements; Procedures for demonstrating compliance with clearance criteria; Experience from radiological assessments associated with decommissioning; Involvement of the local communities and the impact that decommissioning activities has on them. The presented papers and posters were reviewed and accepted following the guidelines established by the Conference Programme Committee for consideration at the Conference. The material compiled in this Book of Contributed Papers has not undergone rigorous editing by the editorial staff of the IAEA. However, certain modifications were made: a unified format was adopted for all papers; and minor corrections were made in the text where required. Each paper and poster has been indexed

International conference on lessons learned from the decommissioning of nuclear facilities and the safe termination of nuclear activities. Contributed papers

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-12-15

The International Atomic Energy Agency (IAEA), in cooperation with the European Commission (EC), Nuclear Energy Agency to the Organisation for Economic Co-operation and Development (OECD/NEA), and the World Nuclear Association (WNA), organized an International Conference on Lessons Learned from the Decommissioning of Nuclear Facilities and the Safe Termination of Nuclear Activities from 11 to 15 December 2006 in Athens, Greece. This Book of Contributed Papers contains technical papers and posters contributed by experts from operating organisations, regulatory bodies, technical support organisations, and other institutions on issues falling within the scope of the Conference. The following main topics were covered: Evolution of national and international policies and criteria for the safe and efficient decommissioning of nuclear facilities and safe termination of nuclear activities; Review of lessons learned from ongoing or completed activities associated with decommissioning; Improvement of safety and efficiency through the use of new and innovative technologies; Practical aspects in the management of material, waste and sites resulting from decommissioning, including the management of waste in the absence of repositories and waste acceptance requirements; Procedures for demonstrating compliance with clearance criteria; Experience from radiological assessments associated with decommissioning; Involvement of the local communities and the impact that decommissioning activities has on them. The presented papers and posters were reviewed and accepted following the guidelines established by the Conference Programme Committee for consideration at the Conference. The material compiled in this Book of Contributed Papers has not undergone rigorous editing by the editorial staff of the IAEA. However, certain modifications were made: a unified format was adopted for all papers; and minor corrections were made in the text where required. Each paper and poster has been indexed

Impedance Characterization and Modeling of Lithium-Ion Batteries Considering the Internal Temperature Gradient

Directory of Open Access Journals (Sweden)

Haifeng Dai

2018-01-01

Full Text Available Battery impedance is essential to the management of lithium-ion batteries for electric vehicles (EVs, and impedance characterization can help to monitor and predict the battery states. Many studies have been undertaken to investigate impedance characterization and the factors that influence impedance. However, few studies regarding the influence of the internal temperature gradient, which is caused by heat generation during operation, have been presented. We have comprehensively studied the influence of the internal temperature gradient on impedance characterization and the modeling of battery impedance, and have proposed a discretization model to capture battery impedance characterization considering the temperature gradient. Several experiments, including experiments with artificial temperature gradients, are designed and implemented to study the influence of the internal temperature gradient on battery impedance. Based on the experimental results, the parameters of the non-linear impedance model are obtained, and the relationship between the parameters and temperature is further established. The experimental results show that the temperature gradient will influence battery impedance and the temperature distribution can be considered to be approximately linear. The verification results indicate that the proposed discretization model has a good performance and can be used to describe the actual characterization of the battery with an internal temperature gradient.

Overview of the international legal framework governing the safe and peaceful uses of nuclear energy - Some practical steps

International Nuclear Information System (INIS)

Rautenbach, J.; Tonhauser, W.; Wetherall, A.

2006-01-01

The accident on 26 April 1986 in unit 4 of the Chernobyl nuclear power plant in the former Ukrainian Republic of the Union of Soviet Socialist Republics, near the present borders of Belarus, the Russian Federation and Ukraine, was categorised at the time as 'the most devastating accident in the history of nuclear power'. Two decades on, the assessment of the health, environmental and socio-economic impacts of the accident still continues, with the aim of providing definitive and authoritative answers. In addition, from a legal perspective the accident underlined some significant deficiencies and gaps in the international legal and regulatory norms that had been established to govern the safe and peaceful uses of nuclear energy. At the same time, it stressed the need for a collective international focus on [nuclear] safety and, in its wake, prompted a call for the creation of an international regime for the safe development of [nuclear energy] under the auspices of the IAEA. For all its devastating consequences, the accident was in fact a wake-up call for the 'international nuclear community' and led to a new era in international nuclear cooperation, involving states which had so far been removed both geographically and technologically from nuclear power. In its aftermath, the international nuclear community, in an attempt to allay concerns of the public and political world over the use of the atom as a viable energy source, sought to rebuild confidence in the safety of nuclear energy, primarily through the IAEA, by urgently addressing those main deficiencies in the existing international legal framework that had been exemplified by the accident. As much as has already been written on the substantive provisions and negotiating history of the different international instruments that compromise this legal framework and that were developed under the auspices of the IAEA in the two decades since the Chernobyl accident, this paper only briefly describes their substance

Inherently safe technologies-chemical and nuclear

International Nuclear Information System (INIS)

Weinberg, A.M.

1984-01-01

Probabilistic risk assessments show an inverse relationship between the likelihood and the consequences of nuclear and chemical plant accidents, but the Bhopal accident has change public complacency about the safety of chemical plants to such an extent that public confidence is now at the same low level as with nuclear plants. The nuclear industry's response was to strengthen its institutions and improve its technologies, but the public may not be convinced. One solution is to develop reactors which do not depend upon the active intervention of humans of electromechanical devices to deal with emergencies, but which have physical properties that limit the possible temperature and power of a reactor. The Process Inherent Ultimately Safe and the modular High-Temperature Gas-Cooled reactors are two possibilities. the chemical industry needs to develop its own inherently safe design precepts that incorporate smallness, safe processes, and hardening against sabotage. 5 references

The international surface temperature initiative

Science.gov (United States)

Thorne, P. W.; Lawrimore, J. H.; Willett, K. M.; Allan, R.; Chandler, R. E.; Mhanda, A.; de Podesta, M.; Possolo, A.; Revadekar, J.; Rusticucci, M.; Stott, P. A.; Strouse, G. F.; Trewin, B.; Wang, X. L.; Yatagai, A.; Merchant, C.; Merlone, A.; Peterson, T. C.; Scott, E. M.

2013-09-01

The aim of International Surface Temperature Initiative is to create an end-to-end process for analysis of air temperature data taken over the land surface of the Earth. The foundation of any analysis is the source data. Land surface air temperature records have traditionally been stored in local, organizational, national and international holdings, some of which have been available digitally but many of which are available solely on paper or as imaged files. Further, economic and geopolitical realities have often precluded open sharing of these data. The necessary first step therefore is to collate readily available holdings and augment these over time either through gaining access to previously unavailable digital data or through data rescue and digitization activities. Next, it must be recognized that these historical measurements were made primarily in support of real-time weather applications where timeliness and coverage are key. At almost every long-term station it is virtually certain that changes in instrumentation, siting or observing practices have occurred. Because none of the historical measures were made in a metrologically traceable manner there is no unambiguous way to retrieve the true climate evolution from the heterogeneous raw data holdings. Therefore it is desirable for multiple independent groups to produce adjusted data sets (so-called homogenized data) to adequately understand the data characteristics and estimate uncertainties. Then it is necessary to benchmark the performance of the contributed algorithms (equivalent to metrological software validation) through development of realistic benchmark datasets. In support of this, a series of successive benchmarking and assessment cycles are envisaged, allowing continual improvement while avoiding over-tuning of algorithms. Finally, a portal is proposed giving access to related data-products, utilizing the assessment results to provide guidance to end-users on which product is the most suited to

The initial safe range of motion of the ankle joint after three methods of internal fixation of simulated fractures of the medial malleolus.

Science.gov (United States)

Shimamura, Yoshio; Kaneko, Kazuo; Kume, Kazuhiko; Maeda, Mutsuhiro; Iwase, Hideaki

2006-07-01

Previous studies have demonstrated the safe passive range of ankle motion for inter-bone stiffness after internal fixation under load but there is a lack of information about the safe range of ankle motion for early rehabilitation in the absence of loading. The present study was designed to assess the effect of ankle movement on inter-bone displacement characteristics of medial malleolus fractures following three types of internal fixation to determine the safe range of motion. Five lower legs obtained during autopsy were used to assess three types of internal fixation (two with Kirschner-wires alone; two with Kirschner-wires plus tension band wiring; and, one with an AO/ASIF malleolar screw alone). Following a simulated fracture by sawing through the medial malleolus the displacement between the fractured bone ends was measured during a passive range of movement with continuous monitoring using omega (Omega) shaped transducers and a biaxial flexible goniometer. Statistical analysis was performed with repeated measures analysis of variance. Inter-bone displacement was not proportional to the magnitude of movement throughout the range of ankle motion as, when separation exceeded 25 microm, there was increasingly wide separation as plantar-flexion or dorsal-flexion was increased. There was no statistical significant difference between the small amount of inter-bone displacement observed with three types of fixation within the safe range of dorsal-flexion and plantar-flexion for early rehabilitation. However the inter-bone separation when fixation utilized two Kirschner-wires alone tended to be greater than when using the other two types of fixation during dorsal-flexion and eversion. The present study revealed a reproducible range of ankle motion for early rehabilitation which was estimated to be within the range of 20 degrees of dorsal-flexion and 10 degrees of plantar-flexion without eversion. Also, internal fixation with two Kirschner-wires alone does not seem to

On the nature of low temperature internal friction peaks in metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Khonik, V.A. [State Pedagogical Univ., Voronezh (Russian Federation); Spivak, L.V. [State Univ., Perm (Russian Federation)

1996-01-01

Low temperature (30 < T < 300 K) internal friction in a metallic glass Ni{sub 60}Nb{sub 40} subjected to preliminary inhomogeneous deformation by cold rolling, homogeneous tensile deformation or electrolytic charging with hydrogen is investigated. Cold rolling or hydrogenation result in appearance of similar internal friction peaks and hysteresis damping. Homogeneous deformation has no influence on low temperature internal friction. The phenomenon of microplastic deformation during hydrogenation of weakly stressed samples is revealed. It is argued that microplastic deformation of metallic glasses during hydrogenation without external stress takes place too. Plastic flow both on cold rolling and hydrogenation occurs via formation and motion of dislocation-like defects which are the reason of the observed anelastic anomalies. It is concluded that low temperature internal friction peaks described in the literature for as-cast, cold deformed and hydrogenated samples have common dislocation-like origin.

General guidelines for safe and expeditious international transport of samples subjected to biological dosimetry assessment.

Science.gov (United States)

Di Giorgio, Marina; Radl, Analía; Taja, María R; Bubniak, Ruth; Deminge, Mayra; Sapienza, Carla; Vázquez, Marina; Baciu, Florian; Kenny, Pat

2014-06-01

It has been observed that victims of accidental overexposures show better chance of survival if they receive medical treatment early. The increased risk of scenarios involving mass casualties has stimulated the scientific community to develop tools that would help the medical doctors to treat victims. The biological dosimetry has become a routine test to estimate the dose, supplementing physical and clinical dosimetry. In case of radiation emergencies, in order to provide timely and effectively biological dosimetry assistance it is essential to guarantee an adequate transport of blood samples in principal, for providing support to countries that do not have biodosimetry laboratories. The objective of the present paper is to provide general guidelines, summarised in 10 points, for timely and proper receiving and sending of blood samples under National and International regulations, for safe and expeditious international transport. These guidelines cover the classification, packaging, marking, labelling, refrigeration and documentation requirements for the international shipping of blood samples and pellets, to provide assistance missions with a tool that would contribute with the preparedness for an effective biodosimetric response in cases of radiological or nuclear emergencies. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Development status of PIUS/ISER - a inherently safe reactor for the international use

International Nuclear Information System (INIS)

Wakabayashi, Hiroaki

1987-01-01

It is just in early 1980s that LWR-based nuclear power has become a substantial power source. Though the safety level of nuclear power is always claimed to be sufficiently high by the industry, it rests on the idea of defense in depth, the calculation by probabilistic risk assessment (PRA) or probabilistic safety assessment (PSA). The TMI-2 and Chernobyl-4 accidents occurred in the industrially most advanced countries. In this paper, an alternative way to safe nuclear power is sought in so-called inherently safe reactors (ISR) including the LWR type PIUS/ISER. With proper consideration into the design of nuclear reactor plants, those can be made basically safe through the use of passive safe mechanism for their design. In short, an ISR is a nuclear power reactor which has passive and intrinsic core cooling capability and automatic shutdown capability. As the nuclear power reactors which are currently claimed to be inherently safe, there are the process inherent and ultimately safe reactor (PIUS) of ASEA-ATOM Sweden and the inherently safe and economical reactor (ISER) of the University of Tokyo, Japan, of LWR type. The current status of the development, the reliability, and some technical problems of ISER/PIUS and the attitude of various countries toward ISER/PIUS are described. (Kako, I.)

Numerical simulation of cometary nuclei. III. Internal temperatures of cometary nuclei

International Nuclear Information System (INIS)

Herman, G.; Weissman, P.R.

1987-01-01

The thermal diffusion equation for the internal temperature of cometary nuclei is exactly solved by means of a one-dimensional numerical model in order to shed light on the complex behavior of these temperatures with varying orbital and thermal parameters and in order to consider possible cometary nucleus thermal evolution targets for comet rendezvous and/or sample-return missions. The concept of new and old comets, classified in terms of how many passages around the sun have been made, may take on new meaning in view of the present demonstration that differences in eccentricity between two comets having the same period and number of apparitions may yield significantly different internal temperature profiles. 19 references

On the nature of low temperature internal friction peaks in metallic glasses

International Nuclear Information System (INIS)

Khonik, V.A.; Spivak, L.V.

1996-01-01

Low temperature (30 60 Nb 40 subjected to preliminary inhomogeneous deformation by cold rolling, homogeneous tensile deformation or electrolytic charging with hydrogen is investigated. Cold rolling or hydrogenation result in appearance of similar internal friction peaks and hysteresis damping. Homogeneous deformation has no influence on low temperature internal friction. The phenomenon of microplastic deformation during hydrogenation of weakly stressed samples is revealed. It is argued that microplastic deformation of metallic glasses during hydrogenation without external stress takes place too. Plastic flow both on cold rolling and hydrogenation occurs via formation and motion of dislocation-like defects which are the reason of the observed anelastic anomalies. It is concluded that low temperature internal friction peaks described in the literature for as-cast, cold deformed and hydrogenated samples have common dislocation-like origin

Analysis of the internal temperature of the cells in a battery pack during SOC balancing

Science.gov (United States)

Mizanur, R.; Rashid, M. M.; Rahman, A.; Zahirul Alam, A. H. M.; Ihsan, S.; Mollik, M. S.

2017-03-01

Lithium-ion batteries are more suitable for the application of electric vehicle due to high energy and power density compared to other rechargeable batteries. However, the battery pack temperature has a great impact on the overall performance, cycle life, normal charging-discharging behaviour and even safety. During rapid charge transferring process, the internal temperature may exceed its allowable limit (460C). In this paper, an analysis of internal temperature during charge balancing and discharging conditions is presented. Specific interest is paid to the effects of temperature on the different rate of ambient temperature and discharging current. Matlab/Simulink Li-ion battery model and quasi-resonant converter base balancing system are used to study the temperature effect. Rising internal temperature depends on the rate of balancing current and ambient temperature found in the simulation results.

A method to measure internal stray radiation of cryogenic infrared imaging systems under various ambient temperatures

Science.gov (United States)

Tian, Qijie; Chang, Songtao; Li, Zhou; He, Fengyun; Qiao, Yanfeng

2017-03-01

The suppression level of internal stray radiation is a key criterion for infrared imaging systems, especially for high-precision cryogenic infrared imaging systems. To achieve accurate measurement for internal stray radiation of cryogenic infrared imaging systems under various ambient temperatures, a measurement method, which is based on radiometric calibration, is presented in this paper. First of all, the calibration formula is deduced considering the integration time, and the effect of ambient temperature on internal stray radiation is further analyzed in detail. Then, an approach is proposed to measure the internal stray radiation of cryogenic infrared imaging systems under various ambient temperatures. By calibrating the system under two ambient temperatures, the quantitative relation between the internal stray radiation and the ambient temperature can be acquired, and then the internal stray radiation of the cryogenic infrared imaging system under various ambient temperatures can be calculated. Finally, several experiments are performed in a chamber with controllable inside temperatures to evaluate the effectiveness of the proposed method. Experimental results indicate that the proposed method can be used to measure internal stray radiation with high accuracy at various ambient temperatures and integration times. The proposed method has some advantages, such as simple implementation and the capability of high-precision measurement. The measurement results can be used to guide the stray radiation suppression and to test whether the internal stray radiation suppression performance meets the requirement or not.

Combined IR imaging-neural network method for the estimation of internal temperature in cooked chicken meat

Science.gov (United States)

Ibarra, Juan G.; Tao, Yang; Xin, Hongwei

2000-11-01

A noninvasive method for the estimation of internal temperature in chicken meat immediately following cooking is proposed. The external temperature from IR images was correlated with measured internal temperature through a multilayer neural network. To provide inputs for the network, time series experiments were conducted to obtain simultaneous observations of internal and external temperatures immediately after cooking during the cooling process. An IR camera working at the spectral band of 3.4 to 5.0 micrometers registered external temperature distributions without the interference of close-to-oven environment, while conventional thermocouples registered internal temperatures. For an internal temperature at a given time, simultaneous and lagged external temperature observations were used as the input of the neural network. Based on practical and statistical considerations, a criterion is established to reduce the nodes in the neural network input. The combined method was able to estimate internal temperature for times between 0 and 540 s within a standard error of +/- 1.01 degree(s)C, and within an error of +/- 1.07 degree(s)C for short times after cooking (3 min), with two thermograms at times t and t+30s. The method has great potential for monitoring of doneness of chicken meat in conveyor belt type cooking and can be used as a platform for similar studies in other food products.

A Mean-Variance Diagnosis of the Financial Crisis: International Diversification and Safe Havens

Directory of Open Access Journals (Sweden)

Alexander Eptas

2010-12-01

Full Text Available We use mean-variance analysis with short selling constraints to diagnose the effects of the recent global financial crisis by evaluating the potential benefits of international diversification in the search for ‘safe havens’. We use stock index data for a sample of developed, advanced-emerging and emerging countries. ‘Text-book’ results are obtained for the pre-crisis analysis with the optimal portfolio for any risk-averse investor being obtained as the tangency portfolio of the All-Country portfolio frontier. During the crisis there is a disjunction between bank lending and stock markets revealed by negative average returns and an absence of any empirical Capital Market Line. Israel and Colombia emerge as the safest havens for any investor during the crisis. For Israel this may reflect the protection afforded by special trade links and diaspora support, while for Colombia we speculate that this reveals the impact on world financial markets of the demand for cocaine.

Monitoring on internal temperature of composite insulator with embedding fiber Bragg grating for early diagnosis

Science.gov (United States)

Chen, Wen; Tang, Ming

2017-04-01

The abnormal temperature rise is the precursor of the defective composite insulator in power transmission line. However no consolidated techniques or methodologies can on line monitor its internal temperature now. Thus a new method using embedding fiber Bragg grating (FBG) in fiber reinforced polymer (FRP) rod is adopted to monitor its internal temperature. To correctly demodulate the internal temperature of FRP rod from the Bragg wavelength shift of FBG, the conversion coefficient between them is deduced theoretically based on comprehensive investigation on the thermal stresses of the metal-composite joint, as well as its material and structural properties. Theoretical model shows that the conversion coefficients of FBG embedded in different positions will be different because of non-uniform thermal stress distribution, which is verified by an experiment. This work lays the theoretical foundation of monitoring the internal temperature of composite insulator with embedding FBG, which is of great importance to its health structural monitoring, especially early diagnosis.

Standards for safe operation of research reactors

International Nuclear Information System (INIS)

1996-01-01

The safety of research reactors is based on many factors such as suitable choice of location, design and construction according to the international standards, it also depends on well trained and qualified operational staff. These standards determine the responsibilities of all who are concerned with the research reactors safe operation, and who are responsible of all related activities in all the administrative and technical stages in a way that insures the safe operation of the reactor

PREFACE: 4th International Conference on Safe Production and Use of Nanomaterials (Nanosafe2014)

Science.gov (United States)

Tardif, F.; Damlencourt, J.-F.; Schuster, F.; Gaultier, V.

2015-05-01

This volume contains a collection of contributions presented at the 4th International Conference on Safe Production and Use of Nanomaterials (NANOSAFE 2014) held in Grenoble, France, from 18th to 20th November 2014. The issues of fast progress in the field of Nanosafety are up to the potential benefits that nanotechnology can bring to mankind. Making more efficient - more sustainable - easier to share mineral resources, increasing the yields of new energy technologies, enabling drugs that act selectively and locally are just few examples of the wide range of nanomaterial applications that currently benefit humanity. Nevertheless, the dynamic development of nanomaterials requires the adhesion from the general public who rightly demand major progresses in Nanosafety as a prerequisite. This is our exciting responsibility and challenge! Following the successful outcome of the three past international conferences on safe production and use of nanomaterials: Nanosafe 2008, 2010 and 2012, the organizing committee has the pleasure to welcoming you again to Minatec, Grenoble with some of the most famous specialists in the field. This year, two new topics have been added dealing with the "New Application of Nanomaterials" and "Nano-responsible Development" in addition to the usual issues addressed in previous Nanosafe conferences such as Expology, Detection and Characterization, Toxicology, Environmental Interactions, Nanomaterials Release, Life Cycle Analysis, Regulation and Standardization, Risk Management. The debates in 2012 proved highly successful so this formula has been kept in 2014 with 3 round tables: Nano-Responsible Development, Risks and Benefits for the Environment, Toxicology Progress. In this 4th edition, there were more than 330 registered participants from 28 different countries including 160 oral presentation covering the whole Nanosafety issues in 12 sessions, satellite workshops and round tables. This high number of participants makes this edition one of

Working safely with ionising radiation

International Nuclear Information System (INIS)

McDowell, D.J.

1990-01-01

A small leaflet provides information on working safely with ionizing radiation. Topics covered include the types of radiation, radiological units, external radiation, contamination and internal radiation, methods of protection form radiation, radiation monitors, protective clothing for contamination, personal dosemeters, radiation dose limits for classified workers and finally the Ionising Radiations Regulations 1985. (UK)

Towards an ethics safe harbor for global biomedical research

Science.gov (United States)

Dove, Edward S.; Knoppers, Bartha M.; Zawati, Ma'n H.

2014-01-01

Although increasingly global, data-driven genomics and other ‘omics’-focused research hold great promise for health discoveries, current research ethics review systems around the world challenge potential improvements in human health from such research. To overcome this challenge, we propose a ‘Safe Harbor Framework for International Ethics Equivalency’ that facilitates the harmonization of ethics review of specific types of data-driven international research projects while respecting globally transposable research ethics norms and principles. The Safe Harbor would consist in part of an agency supporting an International Federation for Ethics Review (IFER), formed by a voluntary compact among countries, granting agencies, philanthropies, institutions, and healthcare, patient advocacy, and research organizations. IFER would be both a central ethics review body, and also a forum for review and follow-up of policies concerning ethics norms for international research projects. It would be built on five principle elements: (1) registration, (2) compliance review, (3) recognition, (4) monitoring and enforcement, and (5) public participation. The Safe Harbor would create many benefits for researchers, countries, and the general public, and may eventually have application beyond (gen)omics to other areas of biomedical research that increasingly engage in secondary use of data and present only negligible risks. PMID:27774154

Safe Grid

Science.gov (United States)

Chow, Edward T.; Stewart, Helen; Korsmeyer, David (Technical Monitor)

2003-01-01

The biggest users of GRID technologies came from the science and technology communities. These consist of government, industry and academia (national and international). The NASA GRID is moving into a higher technology readiness level (TRL) today; and as a joint effort among these leaders within government, academia, and industry, the NASA GRID plans to extend availability to enable scientists and engineers across these geographical boundaries collaborate to solve important problems facing the world in the 21 st century. In order to enable NASA programs and missions to use IPG resources for program and mission design, the IPG capabilities needs to be accessible from inside the NASA center networks. However, because different NASA centers maintain different security domains, the GRID penetration across different firewalls is a concern for center security people. This is the reason why some IPG resources are been separated from the NASA center network. Also, because of the center network security and ITAR concerns, the NASA IPG resource owner may not have full control over who can access remotely from outside the NASA center. In order to obtain organizational approval for secured remote access, the IPG infrastructure needs to be adapted to work with the NASA business process. Improvements need to be made before the IPG can be used for NASA program and mission development. The Secured Advanced Federated Environment (SAFE) technology is designed to provide federated security across NASA center and NASA partner's security domains. Instead of one giant center firewall which can be difficult to modify for different GRID applications, the SAFE "micro security domain" provide large number of professionally managed "micro firewalls" that can allow NASA centers to accept remote IPG access without the worry of damaging other center resources. The SAFE policy-driven capability-based federated security mechanism can enable joint organizational and resource owner approved remote

From Safe Systems to Patient Safety

DEFF Research Database (Denmark)

Aarts, J.; Nøhr, C.

2010-01-01

for the third conference with the theme: The ability to design, implement and evaluate safe, useable and effective systems within complex health care organizations. The theme for this conference was "Designing and Implementing Health IT: from safe systems to patient safety". The contributions have reflected...... and implementation of safe systems and thus contribute to the agenda of patient safety? The contributions demonstrate how the health informatics community has contributed to the performance of significant research and to translating research findings to develop health care delivery and improve patient safety......This volume presents the papers from the fourth International Conference on Information Technology in Health Care: Socio-technical Approaches held in Aalborg, Denmark in June 2010. In 2001 the first conference was held in Rotterdam, The Netherlands with the theme: Sociotechnical' approaches...

Safe operation of critical assemblies and research reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1960-09-15

Some countries have accumulated considerable experience in the operation of these reactors and have in the process developed safe practices. On the other hand, other countries which have recently acquired, or will soon acquire, such reactors do not have sufficient background of experience with them to have developed full knowledge regarding their safe operation. In this situation, the International Atomic Energy Agency has considered that it would be useful to make available to all its Member States a set of recommendations on the safe operation of these reactors, based on the accumulated experience and best practices. The Director General accordingly nominated a Pane Ion Safe Operation of Critical Assemblies and Research Reactors to assist the Agency's Secretariat in drafting such recommendations

Safe disposal of radioactive wastes

International Nuclear Information System (INIS)

Hooker, P.; Metcalfe, R.; Milodowski, T.; Holliday, D.

1997-01-01

A high degree of international cooperation has characterized the two studies reported here which aim to address whether radioactive waste can be disposed of safely. Using hydrogeochemical and mineralogical surveying techniques earth scientists from the British Geological Survey have sought to identify and characterise suitable disposal sites. Aspects of the studies are explored emphasising their cooperative nature. (UK)

Soil inertia and shallow basement envelope impact on cellar internal temperature

Directory of Open Access Journals (Sweden)

Naima Sakami

2016-06-01

Full Text Available This work deals with a three dimensional numerical study of heat transfer by conduction between the soil and the shallow basement in the city of Marrakech (Morocco. The heat transfer equation is solved by the finite difference method using the implicit alternative direction (ADI. The internal temperature of the cellar is computed by using energy balance equation in the cellar. The objective of this work is to evaluate the effects of the nature of the soil, the nature of the walls, the thickness of the walls of the cellar and the distance L far from the cellar on the internal temperature and the heat exchanged between the soil and the shallow basement

Effect of fuel temperature on the methanol spray and nozzle internal flow

International Nuclear Information System (INIS)

Chen, Zhifang; Yao, Anren; Yao, Chunde; Yin, Zenghui; Xu, Han; Geng, Peilin; Dou, Zhancheng; Hu, Jiangtao; Wu, Taoyang; Ma, Ming

2017-01-01

Highlights: • Cavitation region increases with the increasing of methanol temperature. • The nozzle exit velocity increases with the increasing of methanol temperature. • The discharge coefficient decreases with the increasing of methanol temperature. • Droplet SMD reduces when methanol temperature increases measured by PDPA system. • Droplet velocity has the maximum value when methanol temperature is 60 °C. - Abstract: The increasing of fuel temperature can reduce the droplet size and have an advantage of improving spray atomization, while investigations of the effect of temperature on the methanol injector internal flow and external spray is rare. Firstly, a detailed three dimensional numerical simulations of nozzle internal flow have been conducted to probe into the cavitation in methanol injector nozzles, and then an experimental study has been carried out to investigate the droplet size and velocity of methanol spray at various temperatures using the Phase Doppler Particle Analyzer (PDPA) detecting system. And results show that the region of cavitations in nozzle orifice enlarges as methanol temperature and injection pressure increases, and the temperature for 'super-cavitation' occurring decreases gradually with the increasing of injection pressure. Moreover, the nozzle exit velocity, discharge coefficient and cavitations number were also analyzed. However, the discharge coefficient reduces nearly equal under various pressure when the methanol temperature is higher than 60 °C. In addition, the Sauter Mean Diameter (SMD) and velocity of methanol droplet were also analyzed, and found that the droplet velocity reaches the maximum value when the methanol temperature is 60 °C.

Determination of Factors Related to Students' Understandings of Heat, Temperature and Internal Energy Concepts

Science.gov (United States)

Gurcay, Deniz; Gulbas, Etna

2018-01-01

The purpose of this research is to investigate the relationships between high school students' learning approaches and logical thinking abilities and their understandings of heat, temperature and internal energy concepts. Learning Approach Questionnaire, Test of Logical Thinking and Three-Tier Heat, Temperature and Internal Energy Test were used…

SAFE: A computer code for the steady-state and transient thermal analysis of LMR fuel elements

International Nuclear Information System (INIS)

Hayes, S.L.

1993-12-01

SAFE is a computer code developed for both the steady-state and transient thermal analysis of single LMR fuel elements. The code employs a two-dimensional control-volume based finite difference methodology with fully implicit time marching to calculate the temperatures throughout a fuel element and its associated coolant channel for both the steady-state and transient events. The code makes no structural calculations or predictions whatsoever. It does, however, accept as input structural parameters within the fuel such as the distributions of porosity and fuel composition, as well as heat generation, to allow a thermal analysis to be performed on a user-specified fuel structure. The code was developed with ease of use in mind. An interactive input file generator and material property correlations internal to the code are available to expedite analyses using SAFE. This report serves as a complete design description of the code as well as a user's manual. A sample calculation made with SAFE is included to highlight some of the code's features. Complete input and output files for the sample problem are provided

Pregnant women maintain body temperatures within safe limits during moderate-intensity aqua-aerobic classes conducted in pools heated up to 33 degrees Celsius: an observational study.

Science.gov (United States)

Brearley, Amanda L; Sherburn, Margaret; Galea, Mary P; Clarke, Sandy J

2015-10-01

What is the body temperature response of healthy pregnant women exercising at moderate intensity in an aqua-aerobics class where the water temperature is in the range of 28 to 33 degrees Celsius, as typically found in community swimming pools? An observational study. One hundred and nine women in the second and third trimester of pregnancy who were enrolled in a standardised aqua-aerobics class. Tympanic temperature was measured at rest pre-immersion (T1), after 35minutes of moderate-intensity aqua-aerobic exercise (T2), after a further 10minutes of light exercise while still in the water (T3) and finally on departure from the facility (T4). The range of water temperatures in seven indoor community pools was 28.8 to 33.4 degrees Celsius. Body temperature increased by a mean of 0.16 degrees Celsius (SD 0.35, ptemperature response was not related to the water temperature (T2 r = -0.01, p = 0.9; T3 r = -0.02, p=0.9; T4 r=0.03, p=0.8). Analysis of variance demonstrated no difference in body temperature response between participants when grouped in the cooler, medium and warmer water temperatures (T2 F=0.94, p=0.40; T3 F=0.93, p=0.40; T4 F=0.70, p=0.50). Healthy pregnant women maintain body temperatures within safe limits during moderate-intensity aqua-aerobic exercise conducted in pools heated up to 33 degrees Celsius. The study provides evidence to inform guidelines for safe water temperatures for aqua-aerobic exercise during pregnancy. Copyright © 2015 Australian Physiotherapy Association. Published by Elsevier B.V. All rights reserved.

Elevated temperature design of KALIMER reactor internals accounting for creep and stress-rupture effects

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Yoo, Bong

2000-01-01

In most LMFBR (Liquid Metal Fast Breed Reactor) design, the operating temperature is very high and the time-dependent creep and stress-rupture effects become so important in reactor structural design. Therefore, unlike with conventional PWR, the normal operating conditions can be basically dominant design loading because the hold time at elevated temperature condition is so long and enough to result in severe total creep ratcheting strains during total service lifetime. In this paper, elevated temperature design of the conceptually designed baffle annulus regions of KALIMER (Korea Advanced Liquid Metal Reactor) reactor internal structures is carried out for normal operating conditions which have the operating temperature 530 deg. C and the total service lifetime of 30 years. For the elevated temperature design of reactor internal structures, the ASME Code Case N-201-4 is used. Using this code, the time-dependent stress limits, the accumulated total inelastic strain during service lifetime, and the creep-fatigue damages are evaluated with the calculation results by the elastic analysis under conservative assumptions. The application procedures of elevated temperature design of the reactor internal structures using ASME code case N-201-4 with the elastic analysis method are described step by step in detail. This paper will be useful guide for actual application of elevated temperature design of various reactor types accounting for creep and stress-rupture effects. (author)

Online junction temperature measurement via internal gate resistance during turn-on

DEFF Research Database (Denmark)

Baker, Nick; Munk-Nielsen, Stig; Liserre, Marco

2014-01-01

A new method for junction temperature measurement of power semiconductor switches is presented. The measurement exploits the temperature dependent resistance of the temperature sensitive electrical parameter (TSEP): the internal gate resistance. This dependence can be observed during the normal...... switching transitions of an IGBT or MOSFET, and as a result the presented method uses the integral of the gate voltage during the turn-on delay. A measurement circuit can be integrated into a gate driver with no modification to converter or gate driver operation and holds significant advantages over other...

Safe sex

Science.gov (United States)

... sex; Sexually transmitted - safe sex; GC - safe sex; Gonorrhea - safe sex; Herpes - safe sex; HIV - safe sex; ... contact. STIs include: Chlamydia Genital herpes Genital warts Gonorrhea Hepatitis HIV HPV Syphilis STIs are also called ...

Design of a safe cylindrical lithium/thionyl chloride cell

Science.gov (United States)

Johnson, D. H.; Ayers, A. D.; Zupancic, R. L.; Alberto, V. S.; Bailey, J. C.

1984-05-01

Cell design criteria have been established which can result in a safe lithium/thionyl chloride cell. A cell vent, a low area internal anode design, cell balance and composition of the cathode-electrolyte solution have been found to be important factors in the design of a safe cell. In addition to routine testing, both undischarged and discharged cells have been subjected to electrical abuse, environmental abuse and mechanical abuse without disassembly.

Mechanism of high-temperature background of internal friction in metals

International Nuclear Information System (INIS)

Shapoval, B.I.; Arzhavitin, V.M.

1988-01-01

Data of theoretical and experimental studies on energy dissipation in vibrating metal at small amplitudes and elevated temperatures (high temperature background of internal friction) are generalized and systematized. Evolution of knowledge of the background as a phenomenon influenced mainly by crystal structure defects - their form, quantity, mobility and interaction is followed. Considered is a wide range of investigated metal states and measurement conditions, and interrelations with other characteristics, for instance, strength ones. On the basis of the data obtained by authors and other investigations a concept of an additional third stage of the background increase with the temperature - the stage of deviation from exponential dependence at premelting point, is introduced. 107 refs.; 32 figs.; 3 tabs

A dynamic model and an experimental study for the internal air and soil temperatures in an innovative greenhouse

International Nuclear Information System (INIS)

Joudi, Khalid A.; Farhan, Ammar A.

2015-01-01

Highlights: • Simulation model for internal Greenhouse temperature including soil reflectance. • Greenhouse soil heat exchange affects internal temperature by approximately 12%. • Solar air heaters as greenhouse roof maintain better internal temperature year round. - Abstract: An innovative greenhouse which integrates a conventional greenhouse with roof mounted solar air heaters is used in this investigation. This design reduces the solar radiation incoming to the greenhouse in summer which reduced the load and cost of greenhouse cooling and provides a means of solar heating. Experimental measurements of the internal air and internal soil sub-layer temperatures in the greenhouse, without crops, were performed in Baghdad University, Baghdad, Iraq (33.3 °N, 44.4 °E). Measurements were recorded for clear and partly cloudy winter days. A dynamic model was developed to predict the all internal temperatures of the greenhouse. This model includes soil surface heat exchange with the greenhouse air which was found to give a more accurate prediction of the internal temperatures. Soil surface heat exchange has a positive contribution to the internal environment. The input parameters of the model were the measured meteorological conditions and the thermo-physical properties of the greenhouse components which include the cover, inside air, and soil. Comparisons between the predicted and measured results show good agreement. Also, results show that soil sub-layers inside the greenhouse at 50 cm depth are the best place for heat storage elements. The integrated system rendered maximum differences between ambient and internal air temperatures of 16 °C in February and 10 °C in June without operating any heating or cooling system

Inherently safe light water reactors

International Nuclear Information System (INIS)

Ise, Takeharu

1987-01-01

Today's large nuclear power reactors of world-wise use have been designed based on the philosophy. It seems that recent less electricity demand rates, higher capital cost and the TMI accident let us acknowledge relative small and simplified nuclear plants with safer features, and that Chernobyl accident in 1983 underlines the needs of intrinsic and passive safety characteristics. In such background, several inherently safe reactor concepts have been presented abroad and domestically. First describing 'Can inherently safe reactors be designed,' then I introduce representative reactor concepts of inherently safe LWRs advocated abroad so far. All of these innovative reactors employ intrinsic and passive features in their design, as follows: (1) PIUS, an acronym for Process Inherent Ultimate Safety, or an integral PWR with passive heat sink and passive shutdown mechanism, advocated by ASEA-ATOM of Sweden. (2) MAP(Minimum Attention Plant), or a self-pressurized, natural circulation integral PWR, promoted by CE Inc. of the U.S. (3) TPS(TRIGA Power System), or a compact PWR with passive heat sink and inherent fuel characteristics of large prompt temperature coefficient, prompted by GA Technologies Inc. of the U.S. (4) PIUS-BWR, or an inherently safe BWR employing passively actuated fluid valves, in competition with PIUS, prompted by ORNL of the U.S. Then, I will describe the domestic trends in Japan and the innovative inherently safe LWRs presented domestically so far. (author)

Safe handling of plutonium in research laboratories

International Nuclear Information System (INIS)

1976-01-01

The training film illustrates the main basic requirements for the safe handling of small amounts of plutonium. The film is intended not only for people setting up plutonium research laboratories but also for all those who work in existing plutonium research laboratories. It was awarded the first prize in the category ''Protection of Workers'' at the international film festival organized by the 4th World Congress of the International Radiation Protection Association (IRPA) in Paris in April 1977

Safe handling of plutonium in research laboratories

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-12-31

The training film illustrates the main basic requirements for the safe handling of small amounts of plutonium. The film is intended not only for people setting up plutonium research laboratories but also for all those who work in existing plutonium research laboratories. It was awarded the first prize in the category ``Protection of Workers`` at the international film festival organized by the 4th World Congress of the International Radiation Protection Association (IRPA) in Paris in April 1977

Power control of SAFE reactor using fuzzy logic

International Nuclear Information System (INIS)

Irvine, Claude

2002-01-01

Controlling the 100 kW SAFE (Safe Affordable Fission Engine) reactor consists of design and implementation of a fuzzy logic process control system to regulate dynamic variables related to nuclear system power. The first phase of development concentrates primarily on system power startup and regulation, maintaining core temperature equilibrium, and power profile matching. This paper discusses the experimental work performed in those areas. Nuclear core power from the fuel elements is simulated using resistive heating elements while heat rejection is processed by a series of heat pipes. Both axial and radial nuclear power distributions are determined from neuronic modeling codes. The axial temperature profile of the simulated core is matched to the nuclear power profile by varying the resistance of the heating elements. The SAFE model establishes radial temperature profile equivalence by establishing 32 control zones as the nodal coordinates. Control features also allow for slow warm up, since complete shutoff can occur in the heat pipes if heat-source temperatures drop/rise below a certain minimum value, depending on the specific fluid and gas combination in the heat pipe. The entire system is expected to be self-adaptive, i.e., capable of responding to long-range changes in the space environment. Particular attention in the development of the fuzzy logic algorithm shall ensure that the system process remains at set point, virtually eliminating overshoot on start-up and during in-process disturbances. The controller design will withstand harsh environments and applications where it might come in contact with water, corrosive chemicals, radiation fields, etc

Nuclear hydrogen production and its safe handling

International Nuclear Information System (INIS)

Chung, Hongsuk; Paek, Seungwoo; Kim, Kwang-Rag; Ahn, Do-Hee; Lee, Minsoo; Chang, Jong Hwa

2003-01-01

An overview of the hydrogen related research presently undertaken at the Korea Atomic Energy Research Institute are presented. These encompass nuclear hydrogen production, hydrogen storage, and the safe handling of hydrogen, High temperature gas-cooled reactors can play a significant role, with respect to large-scale hydrogen production, if used as the provider of high temperature heat in fossil fuel conversion or thermochemical cycles. A variety of potential hydrogen production methods for high temperature gas-cooled reactors were analyzed. They are steam reforming of natural gas, thermochemical cycles, etc. The produced hydrogen should be stored safely. Titanium metal was tested primarily because its hydride has very low dissociation pressures at normal storage temperatures and a high capacity for hydrogen, it is easy to prepare and is non-reactive with air in the expected storage conditions. There could be a number of potential sources of hydrogen evolution risk in a nuclear hydrogen production facility. In order to reduce the deflagration detonation it is necessary to develop hydrogen control methods that are capable of dealing with the hydrogen release rate. A series of experiments were conducted to assess the catalytic recombination characteristics of hydrogen in an air stream using palladium catalysts. (author)

Failure maps for internally pressurized Zr-2.5% Nb pressure tubes with circumferential temperature variations

International Nuclear Information System (INIS)

Shewfelt, R.S.W.

1986-01-01

During some postulated loss-of-coolant accidents, the pressure tube temperature may rise before the internal pressure drops, causing the pressure tube to balloon. The temperature around the pressure tube circumference would likely be nonuniform, producing localized deformation that could possibly cause failure. The computer program, GRAD, was used to determine the circumferential temperature distribution required to cause an internally pressurized Zr-2.5% Nb pressure tube to fail before coming into full contact with its calandria tube. These results were used to construct failure maps. 7 refs

Maximal combustion temperature estimation

International Nuclear Information System (INIS)

Golodova, E; Shchepakina, E

2006-01-01

This work is concerned with the phenomenon of delayed loss of stability and the estimation of the maximal temperature of safe combustion. Using the qualitative theory of singular perturbations and canard techniques we determine the maximal temperature on the trajectories located in the transition region between the slow combustion regime and the explosive one. This approach is used to estimate the maximal temperature of safe combustion in multi-phase combustion models

Advances in catalysts for internal reforming in high temperature fuel cells

Science.gov (United States)

Dicks, A. L.

Catalytic steam reforming of natural gas is an attractive method of producing the hydrogen required by the present generation of fuel cells. The molten carbonate (MCFC) and solid oxide (SOFC) fuel cells operate at high enough temperatures for the endothermic steam reforming reaction to be carried out within the stack. For the MCFC, the conventional anodes have insufficient activity to catalyse the steam reforming of natural gas. For these cells, internal reforming can be achieved only with the addition of a separate catalyst, preferably located in close proximity to the anode. However, in the so-called `Direct Internal Reforming' configuration, attack from alkali in the MCFC may severely limit catalyst lifetime. In the case of the state-of-the-art SOFC, natural gas can be reformed directly on the nickel cermet anode. However, in the SOFC, temperature variations in the cell caused by the reforming reaction may limit the amount of internal reforming that can be allowed in practice. In addition, some external pre-reforming may be desirable to remove high molecular weight hydrocarbons from the fuel gas, which would otherwise crack to produce elemental carbon. Degradation of the SOFC anode may also be a problem when internal reforming is carried out. This has prompted several research groups to investigate the use of alternative anode materials.

Elimination of bus voltage impact on temperature sensitive electrical parameter during turn-on transition for junction temperature estimation of high-power IGBT modules

DEFF Research Database (Denmark)

Luo, Haoze; Iannuzzo, Francesco; Blaabjerg, Frede

2017-01-01

Junction temperature is of great importance to safe operating area of IGBT modules. Various information of the IGBT operating state is reflected on electrical characteristics during turn-on transient. A unified extraction method for internal junction temperature via dynamic thermo......-sensitive electrical parameters (DTSEP) during turn-on transient is proposed. Two DTSEP, turn-on delay time (tdon) and the maximum increasing rate of collector current dic/dt(max), are combined to eliminate the bus voltage impact. Using the inherent emitter-auxiliary inductor LeE in high-power modules, the temperature......-dependent DTSEPs can be converted into a low-voltage and measurable signal. Finally, experiment results are exhibited to verify the effectiveness of proposed method....

Safe Handling of Radioisotopes

International Nuclear Information System (INIS)

1958-01-01

Under its Statute the International Atomic Energy Agency is empowered to provide for the application of standards of safety for protection against radiation to its own operations and to operations making use of assistance provided by it or with which it is otherwise directly associated. To this end authorities receiving such assistance are required to observe relevant health and safety measures prescribed by the Agency. As a first step, it has been considered an urgent task to provide users of radioisotopes with a manual of practice for the safe handling of these substances. Such a manual is presented here and represents the first of a series of manuals and codes to be issued by the Agency. It has been prepared after careful consideration of existing national and international codes of radiation safety, by a group of international experts and in consultation with other international bodies. At the same time it is recommended that the manual be taken into account as a basic reference document by Member States of the Agency in the preparation of national health and safety documents covering the use of radioisotopes.

A least squares method for a longitudinal fin with temperature dependent internal heat generation and thermal conductivity

International Nuclear Information System (INIS)

Aziz, A.; Bouaziz, M.N.

2011-01-01

Highlights: → Analytical solutions for a rectangular fin with temperature dependent heat generation and thermal conductivity. → Graphs give temperature distributions and fin efficiency. → Comparison of analytical and numerical solutions. → Method of least squares used for the analytical solutions. - Abstract: Approximate but highly accurate solutions for the temperature distribution, fin efficiency, and optimum fin parameter for a constant area longitudinal fin with temperature dependent internal heat generation and thermal conductivity are derived analytically. The method of least squares recently used by the authors is applied to treat the two nonlinearities, one associated with the temperature dependent internal heat generation and the other due to temperature dependent thermal conductivity. The solution is built from the classical solution for a fin with uniform internal heat generation and constant thermal conductivity. The results are presented graphically and compared with the direct numerical solutions. The analytical solutions retain their accuracy (within 1% of the numerical solution) even when there is a 60% increase in thermal conductivity and internal heat generation at the base temperature from their corresponding values at the sink temperature. The present solution is simple (involves hyperbolic functions only) compared with the fairly complex approximate solutions based on the homotopy perturbation method, variational iteration method, and the double series regular perturbation method and offers high accuracy. The simple analytical expressions for the temperature distribution, the fin efficiency and the optimum fin parameter are convenient for use by engineers dealing with the design and analysis of heat generating fins operating with a large temperature difference between the base and the environment.

Expanding the Operational Limits of the Single-Point Impedance Diagnostic for Internal Temperature Monitoring of Lithium-ion Batteries

International Nuclear Information System (INIS)

Spinner, Neil S.; Love, Corey T.; Rose-Pehrsson, Susan L.; Tuttle, Steven G.

2015-01-01

Highlights: • Single-point impedance diagnostic technique demonstrated for lithium-ion batteries • Correlation between imaginary impedance and internal temperature determined • Instantaneous monitoring of commercial lithium-ion battery internal temperature • Expanded temperature range from −10°C up to 95°C • Non-invasive method useful for practical temperature monitoring of commercial cells - Abstract: Instantaneous internal temperature monitoring of a commercial 18650 LiCoO 2 lithium-ion battery was performed using a single-point EIS measurement. A correlation between the imaginary impedance, –Z imag , and internal temperature at 300 Hz was developed that was independent of the battery’s state of charge. An Arrhenius-type dependence was applied, and the activation energy for SEI ionic conductivity was found to be 0.13 eV. Two separate temperature-time experiments were conducted with different sequences of temperature, and single-point impedance tests at 300 Hz were performed to validate the correlation. Limitations were observed with the upper temperature range (68°C < T < 95°C), and consequently a secondary, empirical fit was applied for this upper range to improve accuracy. Average differences between actual and fit temperatures decreased around 3-7°C for the upper range with the secondary correlation. The impedance response at this frequency corresponded to the anode/SEI layer, and the SEI is reported to be thermally stable up to around 100°C, at which point decomposition may occur leading to battery deactivation and/or total failure. It is therefore of great importance to be able to track internal battery temperatures up to this critical point of 100°C, and this work demonstrates an expansion of the single-point EIS diagnostic to these elevated temperatures

FLANGE-ORNL, Flanged Pipe Joint Stress Analysis, Internal Pressure, Moment Loads, Temperature

International Nuclear Information System (INIS)

Rodabaugh, E.C.; Moore, S.E.

1979-01-01

1 - Description of problem or function: FLANGE-ORNL calculates appropriate loads, stresses, and displacements for the flanges, bolts, and gaskets that comprise a flanged piping joint for internal pressure or moment loading on the pipe, temperature difference between the flange hub and ring, and variations in bolt load that result from pressure, hub-ring temperature gradient and/or bolt-ring temperature differences. Flanges considered may be tapered-hub, straight or blind. 2 - Method of solution: The solution is based on discontinuity analysis and the theory of plates and shells

Is selective internal radioembolization safe and effective for patients with inoperable hepatocellular carcinoma and venous thrombosis?

Science.gov (United States)

Woodall, Charles E; Scoggins, Charles R; Ellis, Susan F; Tatum, Clifton M; Hahl, Michael J; Ravindra, Kadiyala V; McMasters, Kelly M; Martin, Robert C G

2009-03-01

The goal of this study was to examine the safety and efficacy of selective internal radioembolization (SIR) for hepatocellular carcinoma (HCC) with portal vein or caval thrombosis (VT), or both. Recent reports have demonstrated that SIR is safe for patients with HCC, but the impact on efficacy of venous thrombosis is unknown. Prospective single-arm study of the use of Therasphere in patients with unresectable HCC enrolled from January 2004 to June 2007. Patients were categorized into three groups based on VT status and therapy. Fifty-two patients were enrolled: 20 patients without VT who received SIR, 15 patients with VT who were treated, and 17 patients (10 with VT) who were not treated because of preprocedure screening failure. Fifty-eight treatments were administered, with a median of two treatments per patient (range of one to three treatments). Child's score was different between groups. Of the VT patients treated, 67% had portal VT, 7% had cava VT, and 26% had both. There were no treatment-related deaths. There was no difference in complications among groups (p = 0.34). Treated patients without thrombosis had a median overall survival of 13.9 months versus 2.7 months for those treated with thrombosis and 5.2 months for the untreated group given best supportive care only (p = 0.01). SIR is safe in patients with HCC. Although SIR can be delivered with minimal morbidity, there might be no benefit for patients with VT. Continued emphasis on multimodality therapy in this population is needed to improve survival.

Serotonin Receptors in the Medulla Oblongata of the Human Fetus and Infant: The Analytic Approach of the International Safe Passage Study

Science.gov (United States)

Folkerth, Rebecca D.; Paterson, David S.; Broadbelt, Kevin G.; Dan Zaharie, S.; Hewlett, Richard H.; Dempers, Johan J.; Burger, Elsie; Wadee, Shabbir; Schubert, Pawel; Wright, Colleen; Sens, Mary Ann; Nelsen, Laura; Randall, Bradley B.; Tran, Hoa; Geldenhuys, Elaine; Elliott, Amy J.; Odendaal, Hein J.; Kinney, Hannah C.

2016-01-01

The Safe Passage Study is an international, prospective study of approximately 12 000 pregnancies to determine the effects of prenatal alcohol exposure (PAE) upon stillbirth and the sudden infant death syndrome (SIDS). A key objective of the study is to elucidate adverse effects of PAE upon binding to serotonin (5-HT) 1A receptors in brainstem homeostatic networks postulated to be abnormal in unexplained stillbirth and/or SIDS. We undertook a feasibility assessment of 5-HT1A receptor binding using autoradiography in the medulla oblongata (6 nuclei in 27 cases). 5-HT1A binding was compared to a reference dataset from the San Diego medical examiner’s system. There was no adverse effect of postmortem interval ≤100 h. The distribution and quantitated values of 5-HT1A binding in Safe Passage Study cases were essentially identical to those in the reference dataset, and virtually identical between stillbirths and live born fetal cases in grossly non-macerated tissues. The pattern of binding was present at mid-gestation with dramatic changes in binding levels in the medullary 5-HT nuclei over the second half of gestation; there was a plateau at lower levels in the neonatal period and into infancy. This study demonstrates feasibility of 5-HT1A binding analysis in the medulla in the Safe Passage Study. PMID:27634962

Issues on safe radioactive waste management at ChNPP site in International Shelter Implementation Plan

International Nuclear Information System (INIS)

Bykov, V.; Kilochytska, T.; Gromyko, S.; Kadkin, Y.; Kondratiev, S.; Pavlenko, A.; Bogorinski, P.

2003-01-01

The International Shelter Implementation Plan (SIP) [1], is aimed to convert the ChNPP unit 4, destroyed by a beyond-design accident in 1986, into an environmentally safe facility by means of large-scale projects such as stabilization of the existing Sarcophagus (Shelter), construction of a New Safe Confinement (NSC), and installation of engineering and monitoring systems. This report presents some important safety issues concerning radioactive waste (RAW) management at the Shelter. One of the main problems of RAW management is to dispose of large volumes of RAW generated during ground preparation work. It is necessary that RAW be sorted carefully to separate low-active radioactive waste (LLW), which will be the majority, from high-level waste. Considering the fact that the Shelter is in the exclusion zone, the interim storage of LLW in this zone is possible, but a set of safety measures is required, e.g. prevention of dust generation or spreading of radioactivity with water. Another problem is high level RAW management. Highly radioactive fragments of the core, including fuel were ejected during the accident and are now buried under the man-made layer around the Shelter. Unanticipated disclosure of such fragments may happen during any ground preparation work as well as during clearing of premises inside the damaged buildings. Therefore, permanent radiation monitoring is required to prevent any intolerable exposure of workers. Unanticipated disclosure of high-active radioactive waste (HLW) could lead to considerable delay of any work. Since it is particularly difficult to remove HLW from those locations, which can not be easily accessed with removal equipment, such waste needs to be confined and properly shielded at in situ. Due to absence of a permanent HLW storage, an interim storage needs to be provided for in the territory of the Sarcophagus. (author)

Zambia Communications Support for Health Safe Love Campaign Outcome Evaluation

Data.gov (United States)

US Agency for International Development — The Safe Love campaign was a three-year comprehensive HIV prevention behavior change and communication (BCC) initiative implemented between June 2011 and June 2014....

International Conference on Fast Reactors and Related Fuel Cycles: Safe Technologies and Sustainable Scenarios (FR13). Presentations

International Nuclear Information System (INIS)

2013-01-01

The conference, which was held from 4 to 7 of March 2013 in Paris, provided a forum to exchange information on national and international programmes, and more generally new developments and experience, in the field of fast reactors and related fuel cycle technologies. A first goal was to identify and discuss strategic and technical options that have been proposed by individual countries or companies. Another goal was to promote the development of fast reactors and related fuel cycle technologies in a safe, proliferation resistant and economic way. A third goal was to identify gaps and key issues that need to be addressed in relation to the industrial deployment of fast reactors with a closed fuel cycle. A fourth goal was to engage young scientists and engineers in this field, in particular with sustainability, innovation, simulation, safety, economics and public acceptance

Randomized controlled trial of internal and external targeted temperature management methods in post- cardiac arrest patients.

Science.gov (United States)

Look, Xinqi; Li, Huihua; Ng, Mingwei; Lim, Eric Tien Siang; Pothiawala, Sohil; Tan, Kenneth Boon Kiat; Sewa, Duu Wen; Shahidah, Nur; Pek, Pin Pin; Ong, Marcus Eng Hock

2018-01-01

Targeted temperature management post-cardiac arrest is currently implemented using various methods, broadly categorized as internal and external. This study aimed to evaluate survival-to-hospital discharge and neurological outcomes (Glasgow-Pittsburgh Score) of post-cardiac arrest patients undergoing internal cooling verses external cooling. A randomized controlled trial of post-resuscitation cardiac arrest patients was conducted from October 2008-September 2014. Patients were randomized to either internal or external cooling methods. Historical controls were selected matched by age and gender. Analysis using SPSS version 21.0 presented descriptive statistics and frequencies while univariate logistic regression was done using R 3.1.3. 23 patients were randomized to internal cooling and 22 patients to external cooling and 42 matched controls were selected. No significant difference was seen between internal and external cooling in terms of survival, neurological outcomes and complications. However in the internal cooling arm, there was lower risk of developing overcooling (p=0.01) and rebound hyperthermia (p=0.02). Compared to normothermia, internal cooling had higher survival (OR=3.36, 95% CI=(1.130, 10.412), and lower risk of developing cardiac arrhythmias (OR=0.18, 95% CI=(0.04, 0.63)). Subgroup analysis showed those with cardiac cause of arrest (OR=4.29, 95% CI=(1.26, 15.80)) and sustained ROSC (OR=5.50, 95% CI=(1.64, 20.39)) had better survival with internal cooling compared to normothermia. Cooling curves showed tighter temperature control for internal compared to external cooling. Internal cooling showed tighter temperature control compared to external cooling. Internal cooling can potentially provide better survival-to-hospital discharge outcomes and reduce cardiac arrhythmia complications in carefully selected patients as compared to normothermia. Copyright © 2017. Published by Elsevier Inc.

Low-temperature internal friction in high-purity monocrystalline and impure polycrystalline niobium after plastic deformation

International Nuclear Information System (INIS)

Wasserbaech, W.; Thompson, E.

2001-01-01

The internal friction Q -1 of plastically deformed, high-purity monocrystalline and impure polycrystalline niobium specimens was measured in the temperature range between 65 mK and about 2 K. Plastic deformation has a pronounced effect on the internal friction Q -1 of the high-purity monocrystalline specimens, and the effect has been found to be almost temperature independent. By contrast, surprisingly, the internal friction Q -1 of the impure polycrystalline specimens was found to be almost independent of the extent of plastic deformation. Comparison of the experimental results with different models of a dynamic scattering of acoustic phonons by dislocations leads to the conclusion that the results cannot be explained with the two-level tunneling model. Instead it is suggested that a strong interaction between acoustic phonons and geometrical kinks in non-screw dislocations is responsible for the observed internal friction Q -1 . (orig.)

The top 10 list for a safe and effective sign-out.

Science.gov (United States)

Kemp, Clinton D; Bath, Jonathan M; Berger, Jonathan; Bergsman, Aaron; Ellison, Trevor; Emery, Katherine; Garonzik-Wang, Jacqueline; Hui-Chou, Helen G; Mayo, Skye C; Serrano, Oscar K; Shridharani, Sachin; Zuberi, Kashif; Lipsett, Pamela A; Freischlag, Julie A

2008-10-01

With the advent of the 80-hour workweek, much attention has been focused on the benefits of shorter work hours regarding resident fatigue and reduced medical errors. Along with this change, however, there has been more reliance on multiple teams of residents who assume the care of inpatients at different times. In this new paradigm, a safe and effective sign-out process is needed to ensure a seamless transition of care from one resident to another. Several studies have been published on the sign-out process among interns in internal medicine, but the literature is sparse with regards to the best way to hand over care of a busy inpatient surgical service. To aid in this process, the Halsted surgical interns performed a review of the current literature on this topic. They also reflected on their personal experiences and developed a 10-point method for safe and effective sign-outs. This process is emphasized for incoming interns and used across the various surgical services at The Johns Hopkins Hospital.

On the nature of low temperature internal friction peaks in metallic glasses

NARCIS (Netherlands)

Khonik, VA; Spivak, LV

Low temperature (30 internal friction in a metallic glass Ni60Nb40 subjected to preliminary inhomogeneous deformation by cold rolling, homogeneous tensile deformation or electrolytic charging with hydrogen is investigated. Cold rolling or hydrogenation result in appearance of similar

Operationalizing safe operating space for regional social-ecological systems.

Science.gov (United States)

Hossain, Md Sarwar; Dearing, John A; Eigenbrod, Felix; Johnson, Fiifi Amoako

2017-04-15

This study makes a first attempt to operationalize the safe operating space concept at a regional scale by considering the complex dynamics (e.g. non-linearity, feedbacks, and interactions) within a systems dynamic model (SD). We employ the model to explore eight 'what if' scenarios based on well-known challenges (e.g. climate change) and current policy debates (e.g. subsidy withdrawal). The findings show that the social-ecological system in the Bangladesh delta may move beyond a safe operating space when a withdrawal of a 50% subsidy for agriculture is combined with the effects of a 2°C temperature increase and sea level rise. Further reductions in upstream river discharge in the Ganges would push the system towards a dangerous zone once a 3.5°C temperature increase was reached. The social-ecological system in Bangladesh delta may be operated within a safe space by: 1) managing feedback (e.g. by reducing production costs) and the slow biophysical variables (e.g. temperature, rainfall) to increase the long-term resilience, 2) negotiating for transboundary water resources, and 3) revising global policies (e.g. withdrawal of subsidy) that negatively impact at regional scales. This study demonstrates how the concepts of tipping points, limits to adaptations, and boundaries for sustainable development may be defined in real world social-ecological systems. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Temperature dependent measurement of internal damping of austenitic stainless steels

Directory of Open Access Journals (Sweden)

Oravcová Monika

2018-01-01

Full Text Available This article is aimed on the analysis of the internal damping changes of austenitic stainless steels AISI 304, AISI 316L and AISI 316Ti depending from temperature. In experimental measurements only resonance method was used which is based on continuous excitation of oscillations of the specimens and the whole apparatus vibrates at the frequency near to the resonance. Microplastic processes and dissipation of energy within the metals are evaluated and investigated by internal damping measurements. Damping capacity of materials is closely tied to the presence of defects including second phase particles and voids. By measuring the energy dissipation in the material, we can determine the elastic characteristics, Youngs modulus, the level of stress relaxation and many other.

General problems associated with the control and safe use of radiation sources (199)

International Nuclear Information System (INIS)

Ahmed, J.U.

1993-01-01

There are problems at various levels in ensuring safety in the use of radiation sources. A relatively new problem that warrants international action is the smuggling of radioactive material across international borders. An international convention on the control and safe use of radiation sources is essential to provide a universally harmonized mechanism for ensuring safety

76 FR 12719 - Safe Schools/Healthy Students Program; Office of Safe and Drug-Free Schools; Safe Schools/Healthy...

Science.gov (United States)

2011-03-08

... DEPARTMENT OF EDUCATION Safe Schools/Healthy Students Program; Office of Safe and Drug- Free Schools; Safe Schools/Healthy Students Program; Catalog of Federal Domestic Assistance (CFDA) Numbers: 84... priorities, requirements, and definitions under the Safe Schools/Healthy Students (SS/HS) program. Since...

Temperature dependence of Young's modulus and internal friction of G-10CR and G-11CR epoxy resins

International Nuclear Information System (INIS)

Ledbetter, H.M.; Maerz, G.

1980-01-01

The Young's moduli of the epoxy-resin matrix material used in NEMA-designation G-10CR and G-11CR fiberglass-cloth-reinforced composites were measured dynamically and semicontinuously between ambient and liquid-nitrogen temperatures. Both materials exhibit regular temperature behavior, showing large Young's-modulus changes, about 125 and 50%, respectively. Internal friction decreased about 80% during cooling to liquid-nitrogen temperature (76 0 K). The different thermoelastic coefficients of the two materials indicate a different internal structure

International consensus on safety principles

International Nuclear Information System (INIS)

Warnecke, E.

1993-01-01

The International Atomic Energy Agency (IAEA) has been regularly requested by its Member States to provide evidence that radioactive waste can be managed safely and to help demonstrate a harmonization of approach at the international level by providing safety documents. In response, IAEA established a special series of safety documents devoted to radioactive waste management. These documents will be elaborated within the Radioactive Waste Safety Standards (RADWASS) programme [1,2] which covers all aspects of radioactive waste management. The RADWASS programme develops a series of international consensus documents on all parts of the safe management of radioactive waste, including disposal. The purpose of the RADWASS programme is to (i) document existing international consensus in the approaches and methodologies for safe radioactive waste management, (ii) create a mechanism to establish consensus where it does not exist and (iii) provide Member States with a comprehensive series of internationally agreed upon documents to complement national standards and criteria. This paper describes the RADWASS programme, and covers the structure, implementation plans and status of documents under preparation

Measuring internal friction at sonic and ultrasonic frequencies in high temperature superconductors

International Nuclear Information System (INIS)

Anderson, A.R.; Russell, G.J.

1996-01-01

Internal friction measurements provide a sensitive means for probing some structural properties of materials. Defect relaxation processes and phase changes are frequently reflected in internal friction measurements as a function of temperature. Relaxation processes associated with oxygen content have been observed in YBCO and BSCCO (2212). By measuring the internal friction at different frequencies activation energies associated with relaxation processes can be determined. Structural changes are temperature dependent and independent of frequency. The composite bar technique developed employs a piezoelectric quartz bar (with lengths of 2 cm or 3 cm and resonant frequencies of approximately 85 kHz or 120 kHz) with a resonant bar of HTSC attached to one end. The quartz bar is suspended at its nodal points and the system excited electrically using a regenerative feedback system. The composite bar method can also be used at low kilohertz frequencies by attaching the HTSC specimen used in the previous technique to the end of a much longer (e g 30 cm) fused silica rod which has very low damping. The resulting composite bar can be excited electrostatically or electromagnetically at frequencies below 10 kHz. The internal friction can be measured by scanning through the resonant frequency and measuring the bandwidth or by observing the decay of free oscillation in the bar. The advantage of using the two composite bar techniques is that the measurements can be made on the same specimen at different frequencies

Safe transport of radioactive materials in Egypt

International Nuclear Information System (INIS)

El-Shinawy, R.M.K.

1994-01-01

In Egypt the national regulations for safe transport of radioactive materials (RAM) are based on the International Atomic Energy Agency (IAEA) regulations. In addition, regulations for the safe transport of these materials through the Suez Canal (SC) were laid down by the Egyptian Atomic Energy Authority (EAEA) and the Suez Canal Authority (SCA). They are continuously updated to meet the increased knowledge and the gained experience. The technical and protective measures taken during transport of RAM through SC are mentioned. Assessment of the impact of transporting radioactive materials through the Suez Canal using the INTERTRAN computer code was carried out in cooperation with IAEA. The transported activities and empty containers, the number of vessels carrying RAM through the canal from 1963 and 1991 and their nationalities are also discussed. The protective measures are mentioned. A review of the present situation of the radioactive wastes storage facilities at the Atomic Energy site at Inshas is given along with the regulation for safe transportation and disposal of radioactive wastes. (Author)

Managing radioactive waste safely. Engaging Scotland

International Nuclear Information System (INIS)

Elrick, D.; Boyes, L.; McCormick, J.

2002-01-01

Between January and May 2002 the Scottish Council Foundation undertook a research project to assess 1 the level of public awareness about and interest in engaging the public in decision-making on managing radioactive waste safely in Scotland. This paper presents the main findings from the research that involved 70 people from across Scotland, aged between 14 and over 65 years old, and a literature review of Scottish, UK and international experience in engaging the public

Study on phase transformations in superconducting Ti-50%Nb alloy using temperature-dependent internal friction method

International Nuclear Information System (INIS)

Shapoval, B.I.; Tikhinskij, G.F.; Somov, A.I.; Chernyj, O.V.; Rudycheva, T.Yu.; Andrievskaya, N.F.

1980-01-01

The internal friction method is used to study phase transformations in the Ti-50%Nb alloy parallel with other methods. The effect of annealing temperature and time, as well as the content of interstitial impurities in the alloy and its thermomechanical treatment (TMT) is studied. In the 250-300 deg C temperature range the complex maximum of internal friction caused by extraction of secondary phases is observed. The latter is confirmed by the measurement data of mechanical properties and electron microscopic analysis. The maximum consists of three overlapping peaks that reflects stepped form of the decomposition process of the metastable solid solution. The preliminary thermo-mechanical alloy treatment consisting of equidirectional plastic deformation with the following recrystallization annealing leads to peak increase. This fact testifies to the stimulating effect of thermo-mechanical treatment on the degree of solid solution decomposition and reveals in the increase of the critical current density of a wire made of the ingot. The increase of the interstitial impurity content in the alloy has the analogous effect. The reduction of the internal friction level during isothermal stand-up at temperatures higher than the third peak temperature proceeds in two stages [ru

Cool and Safe: Multiplicity in Safe Innovation at Unilever

Science.gov (United States)

Penders, Bart

2011-01-01

This article presents the making of a safe innovation: the application of ice structuring protein (ISP) in edible ices. It argues that safety is not the absence of risk but is an active accomplishment; innovations are not "made safe afterward" but "safe innovations are made". Furthermore, there are multiple safeties to be accomplished in the…

Into 21 century with the safe 'Ukrittya' shelter

International Nuclear Information System (INIS)

Kupnij, V.Yi.; Tovstogan, A.S.

2002-01-01

There exists a considerable vagueness in present situation with 'Ukrittya', its main components, and high risk in construction works, as well as nuclear, fire and ecological danger. All these problems are considered and discussed. The final aim consists in complete cleaning of the Unit-4 from nuclear wastes and to make it safe according to international standards

Cost-competitive, inherently safe LFMBR pool plant

International Nuclear Information System (INIS)

McDonald, J.S.; Brunings, J.E.; Chang, Y.I.; Hren, R.R.; Seidensticker, R.W.

1984-01-01

The Cost-Competitive, Inherently Safe LMFBR Pool Plant design was prepared in GFY 1983 under a DOE-sponsored program. This plant design was developed as a joint effort by Rockwell International and the Argonne National Laboratory with major contributions from the Bechtel Group, Inc.; Combustion engineering, Inc.; the Chicago Bridge and Iron Company; and the General Electric Company. Using current LMFBR technology, many innovative features were developed and incorporated into the design to meet the ultimate objectives of the Breeder Program, i.e., energy costs competitive with LWRs and inherent safety features to maintain the plant in a safe condition following assumed accidents without requiring operator action. This paper provides a description of the principal features that were incorporated into the design to achieve low cost and inherent safety

Glass and crystallization like transitions at low temperature in Zr-Cu based glasses by internal friction measurements

Directory of Open Access Journals (Sweden)

Aboki A.T.

2011-05-01

Full Text Available Low temperature β internal friction peak evolution upon thermal cycles shows two peculiar peaks similar to high temperature internal friction peak. The modulus softening associated to these peaks suggest a phase transformation phenomenon and the relaxation time τo in order of 10-23–10-35s, close to that observed in grains boundary sliding are due to interface motions in the amorphous structure under combined thermal and mechanical energies.

Exoskeleton may influence the internal body temperatures of Neotropical dung beetles (Col. Scarabaeinae

Directory of Open Access Journals (Sweden)

Valentina Amore

2017-05-01

Full Text Available The insect exoskeleton is a multifunctional coat with a continuum of mechanical and structural properties constituting the barrier between electromagnetic waves and the internal body parts. This paper examines the ability of beetle exoskeleton to regulate internal body temperature considering its thermal permeability or isolation to simulated solar irradiance and infrared radiation. Seven Neotropical species of dung beetles (Coleoptera, Scarabaeinae differing in colour, surface sculptures, size, sexual dimorphism, period of activity, guild category and altitudinal distribution were studied. Specimens were repeatedly subjected to heating trials under simulated solar irradiance and infrared radiation using a halogen neodymium bulb light with a balanced daylight spectrum and a ceramic infrared heat emitter. The volume of exoskeleton and its weight per volume unit were significantly more important for the heating rate at the beginning of the heating process than for the asymptotic maximum temperature reached at the end of the trials: larger beetles with relatively thicker exoskeletons heated more slowly. The source of radiation greatly influences the asymptotic temperature reached, but has a negligible effect in determining the rate of heat gain by beetles: they reached higher temperatures under artificial sunlight than under infrared radiation. Interspecific differences were negligible in the heating rate but had a large magnitude effect on the asymptotic temperature, only detectable under simulated sun irradiance. The fact that sun irradiance is differentially absorbed dorsally and transformed into heat among species opens the possibility that differences in dorsal exoskeleton would facilitate the heat gain under restrictive environmental temperatures below the preferred ones. The findings provided by this study support the important role played by the exoskeleton in the heating process of beetles, a cuticle able to act passively in the thermal

Exoskeleton may influence the internal body temperatures of Neotropical dung beetles (Col. Scarabaeinae).

Science.gov (United States)

Amore, Valentina; Hernández, Malva I M; Carrascal, Luis M; Lobo, Jorge M

2017-01-01

The insect exoskeleton is a multifunctional coat with a continuum of mechanical and structural properties constituting the barrier between electromagnetic waves and the internal body parts. This paper examines the ability of beetle exoskeleton to regulate internal body temperature considering its thermal permeability or isolation to simulated solar irradiance and infrared radiation. Seven Neotropical species of dung beetles (Coleoptera, Scarabaeinae) differing in colour, surface sculptures, size, sexual dimorphism, period of activity, guild category and altitudinal distribution were studied. Specimens were repeatedly subjected to heating trials under simulated solar irradiance and infrared radiation using a halogen neodymium bulb light with a balanced daylight spectrum and a ceramic infrared heat emitter. The volume of exoskeleton and its weight per volume unit were significantly more important for the heating rate at the beginning of the heating process than for the asymptotic maximum temperature reached at the end of the trials: larger beetles with relatively thicker exoskeletons heated more slowly. The source of radiation greatly influences the asymptotic temperature reached, but has a negligible effect in determining the rate of heat gain by beetles: they reached higher temperatures under artificial sunlight than under infrared radiation. Interspecific differences were negligible in the heating rate but had a large magnitude effect on the asymptotic temperature, only detectable under simulated sun irradiance. The fact that sun irradiance is differentially absorbed dorsally and transformed into heat among species opens the possibility that differences in dorsal exoskeleton would facilitate the heat gain under restrictive environmental temperatures below the preferred ones. The findings provided by this study support the important role played by the exoskeleton in the heating process of beetles, a cuticle able to act passively in the thermal control of body

Comparison of Different Energy Levels of Er:YAG Laser Regarding Intrapulpal Temperature Change During Safe Ceramic Bracket Removal.

Science.gov (United States)

Nalbantgil, Didem; Tozlu, Murat; Oztoprak, Mehmet Oguz

2018-04-01

This study was done to compare the intrapulpal temperature change generated by different energy levels of Er:YAG laser used during debonding of ceramic brackets and find the most suitable level for clinical use. Eighty polycrystalline alumina brackets were bonded on bovine incisor teeth, which were randomly divided into 4 groups of 20. One group was assigned as control. In the study groups, after laser exposure with 2, 4, or 6 Watt energy levels, brackets were debonded using an Instron Universal Testing machine. Adhesive remnant index (ARI) scores were recorded to evaluate the site of debonding. To assess intrapulpal thermal increase, 60 human premolar teeth that were prepared in the same way, at the same energy levels, by a thermocouple were used. When the debonding forces, intrapulpal temperature increases, and ARI of the groups were examined, statistically significant difference was observed between the groups. Mean temperature increases of 0.67°C ± 0.12°C, 1.25°C ± 0.16°C, and 2.36°C ± 0.23°C were recorded for the 2, 4, and 6 Watt laser groups. The mean shear bond strength was 21.35 ± 3.43 megapascals (MPa) for the control group, whereas they were 8.79 ± 2.47, 3.28 ± 0.73, and 2.46 ± 0.54 MPa for the 2, 4, and 6 Watt laser groups, respectively. Four watts is the most efficient and safe energy level to be used, utilizing Er:YAG laser with water cooling spray for 6 sec by scanning method during debonding of polycrystalline alumina brackets without any carbonization effects and detrimental temperature changes at debond sites.

Internal quantum efficiency and tunable colour temperature in monolithic white InGaN/GaN LED

Science.gov (United States)

Titkov, Ilya E.; Yadav, Amit; Zerova, Vera L.; Zulonas, Modestas; Tsatsulnikov, Andrey F.; Lundin, Wsevolod V.; Sakharov, Alexey V.; Rafailov, Edik U.

2014-03-01

Internal Quantum Efficiency (IQE) of two-colour monolithic white light emitting diode (LED) was measured by temperature dependant electro-luminescence (TDEL) and analysed with modified rate equation based on ABC model. External, internal and injection efficiencies of blue and green quantum wells were analysed separately. Monolithic white LED contained one green InGaN QW and two blue QWs being separated by GaN barrier. This paper reports also the tunable behaviour of correlated colour temperature (CCT) in pulsed operation mode and effect of self-heating on device performance.

The high temperature out-of-pile test of LVDT for internal pressure measurement of nuclear fuel rod

Energy Technology Data Exchange (ETDEWEB)

Son, J. M.; Kim, B. K.; Kim, D. S.; Yoon, K. B.; Sin, Y. T.; Park, S. J.; Kang, Y. H. [KAERI, Taejon (Korea, Republic of)

2002-10-01

As a part of the development of instrumentation technologies for the nuclear fuel irradiation test in HANARO(High-flux Advanced Nuclear Application Reactor), the internal pressure measurement technique of the nuclear fuel rod is being developed using LVDT(Linear Variable Differential Transformer). As the results of out-of-pile test at room temperature, it was concluded that the well qualified out-of-pile tests were needed to understand the LVDT's detail characteristics at high temperature for the detail design of the fuel irradiation capsule, because LVDT is very sensitive to variation of temperature. Therefore, the high temperature out-of-pile test system for pressure measurement was developed, and this test was performed under the temperature condition between room temperature and 300 .deg. C increasing the pressure from 0 bar to 30 bar. The LVDT's high temperature characteristics and temperature sensitivity of LVDT were analyzed through this experiment. Based on the result of this test, the method for the application of LVDT at high temperature was introduced. It is known that the results will be used to predict accurately the internal pressure of fuel rod during irradiation test.

Transportation of perishable and refrigerated foods in mylar foil bags and insulated containers: a time-temperature study.

Science.gov (United States)

Li, Yanyan; Schrade, John P; Su, Haiyan; Specchio, John J

2014-08-01

Data are lacking on the temperature changes of food during transport without the use of refrigerated trucks. The purpose of this study was to evaluate the ability of several insulated and noninsulated containers with or without frozen gel packs to keep perishable and refrigerated foods within the temperature safe zone in relationship to duration of transport. The study was designed to duplicate the practices exhibited by customers purchasing perishable food products from a cash-and-carry business. Approximately 40 perishable food items were evaluated. Four types of containers were tested: a mylar foil bag, a commercial insulated bag, a generic insulated bag, and a commercial insulated blanket. Mixed foods were placed into these containers with or without frozen gel packs, transported in unrefrigerated vehicles, and monitored for 4 h for temperature changes. Two environmental temperatures, room temperature of 21.1°C and a stress temperature of 37.8°C, were evaluated. The internal temperature and surface temperature of the food products in these containers increased slowly but remained well below the U.S. Food and Drug Administration Food Code requirements. The various containers were similar in their ability to retain coolness. The presence of frozen gel packs dramatically enhanced the cold-holding capacity of the containers. The temperature of foods increased more rapidly when stressed in a heated environment. The containers tested used with the frozen gel packs can keep the surface and internal temperatures of various perishable foods (starting at 4.4°C or less) within the Food Code recommendation of under 21.1°C for 4 h. Cash-and-carry businesses should strongly encourage their retail customers to utilize these containers with frozen gel packs to safely transport perishable foods.

Design of an integrated information management system for safe management of radioactive waste

International Nuclear Information System (INIS)

Son, Dong Chan; Hong, Suk Young; An, Kyoung Il

2003-05-01

An integrated data management system for the safe management of radioactive waste and spent fuel in Korea is developed to collect basic information, provide the framework for national regulation, and improve national competition and efficiency in the management of radioactive waste and spent fuel. This system can also provide public access to information such as a statistical graphs and integrated data from various waste generators to meet increased public needs and interests. Objectives can be summarized as: the five principles (independence, openness, clearance, efficiency and reliance) of safety regulation can be realized. Public understanding and reliance on the safety of spent fuel and radioactive waste management can be promoted by providing reliable information. Ensure an openness within the international nuclear community and efficiently support international agreements among contracting parties by operating safe and efficient management of spent fuel and radioactive waste (IAEA joint convention on the safety of spent fuel management and on the safety of radioactive waste management). The system can compensate for the imperfections in safe regulation of radioactive waste and spent fuel management related to waste generation, storage and disposal, and make it possible to holistic control. Re-organize the basic framework of KINS's intermediate and long term research organization and trends, regarding waste management policy is to integrate safe management and unit safe disposal

Design of an integrated information management system for safe management of radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Son, Dong Chan; Hong, Suk Young; An, Kyoung Il [Daesang Information Technology Co., Ltd., Seoul (Korea, Republic of)] (and others)

2003-05-15

An integrated data management system for the safe management of radioactive waste and spent fuel in Korea is developed to collect basic information, provide the framework for national regulation, and improve national competition and efficiency in the management of radioactive waste and spent fuel. This system can also provide public access to information such as a statistical graphs and integrated data from various waste generators to meet increased public needs and interests. Objectives can be summarized as: the five principles (independence, openness, clearance, efficiency and reliance) of safety regulation can be realized. Public understanding and reliance on the safety of spent fuel and radioactive waste management can be promoted by providing reliable information. Ensure an openness within the international nuclear community and efficiently support international agreements among contracting parties by operating safe and efficient management of spent fuel and radioactive waste (IAEA joint convention on the safety of spent fuel management and on the safety of radioactive waste management). The system can compensate for the imperfections in safe regulation of radioactive waste and spent fuel management related to waste generation, storage and disposal, and make it possible to holistic control. Re-organize the basic framework of KINS's intermediate and long term research organization and trends, regarding waste management policy is to integrate safe management and unit safe disposal.

PREFACE: Nanosafe2010: International Conference on Safe Production and Use of Nanomaterials

Science.gov (United States)

Sentein, Carole; Schuster, Frédéric; Tardif, François

2011-07-01

Conference logo The second edition of the international conference on the "Safe production and use of nanomaterials" - NanoSafe2010 - was held between 16-18 November at the Maison Minatec congress center located in Grenoble, France. As is recognised, the rapidly developing field of nanotechnologies presents many opportunities and benefits for new materials with significantly improved properties as well as revolutionary applications in the fields of energy, environment, medicine, etc. However, the potential impact of these new materials on human health and the environment is viewed with apprehension. All the security aspects have to be solved in order to reach an acceptable level of risk. The new nano industry can only develop dynamically if these legitimate concerns are satisfactory allayed. Initiated within the framework of the Integrated European project NanoSafe2 and funded by the European Commission under FP6 programs, this biennial event was organized by the French Commissariat à l'Energie Atomique (CEA). NanoSafe2010 had broad international participation from 30 countries representing 4 continents, with registered delegates numbering over 300. The scientific program involved the presentation and discussion of 175 papers, classified as 13 plenary lectures, 117 oral presentations and 45 posters. The conference attracted many of the best known leading scientists and specialists from almost all of the different fields of expertise covering nanosafety issues: Exposure, Characterisation, Detection, Monitoring, Life cycle, Toxicology, Environmental impact, Personal protection, Secure industrial production, Safety parameter evaluation, Standardization, Regulation, and Education. An exhibition took place in parallel with the conference where 16 exhibitors presented the commercial equipment available today in relation to safety during the production or the use of nanomaterials. We believe that this conference, with the above topics, has provided a forum where the many

Factors influencing internal color of cooked meats.

Science.gov (United States)

Suman, Surendranath P; Nair, Mahesh N; Joseph, Poulson; Hunt, Melvin C

2016-10-01

This manuscript overviews the pertinent research on internal color of uncured cooked meats, biochemical processes involved in meat cookery, and fundamental mechanisms governing myoglobin thermal stability. Heat-induced denaturation of myoglobin, responsible for the characteristic dull-brown color of cooked meats, is influenced by a multitude of endogenous (i.e., pH, muscle source, species, redox state) and exogenous (i.e., packaging, ingredients, storage) factors. The interactions between these factors critically influence the internal cooked color and can confuse the consumers, who often perceive cooked color to be a reliable indicator for doneness and safety. While certain phenomena in cooked meat color are cosmetic in nature, others can mislead consumers and result in foodborne illnesses. Research in meat color suggests that processing technologies and cooking practices in industry as well as households influence the internal cooked color. Additionally, the guidelines of many international public health and regulatory authorities recommend using meat thermometers to determine safe cooking endpoint temperature and to ensure product safety. Copyright © 2016 Elsevier Ltd. All rights reserved.

The safe management of sources of radiation: Principles and strategies. INSAG-11. A report by the International Nuclear Safety Advisory Group

International Nuclear Information System (INIS)

1999-01-01

The IAEA activities relating to nuclear safety are based upon a number of premises. First and foremost, each Member State bears full responsibility for the safety of its nuclear facilities. States can be advised, but cannot be relieved of this responsibility. Secondly, much can be gained by exchanging experience; lessons learned can prevent accidents. Finally, the image of nuclear safety is international; a serious accident anywhere affects the public view of nuclear power everywhere. With the intention of strengthening its contribution to ensuring safety of nuclear power plants, the IAEA established the International Safety Advisory Group (INSAG), whose duties include serving as a forum for the exchange of information on nuclear safety issues of international significance and formulating commonly shared safety principles. The present report deals with the general principles governing the safety of all sources of radiation and with application of these principles. It intends to show that, at the conceptual level, the distinction traditionally made between nuclear safety and radiation protection is hardly justifiable. It is intended primarily for those non-specialists who need to take decisions about safe management of sources of radiation and who wish to gain a better understanding of the approach followed in managing the safety of these sources

Small intrinsically safe reactor implications

International Nuclear Information System (INIS)

Wakabayashi, Hiroaki

1985-01-01

Reviewing the history of nuclear power, it is found that peaceful uses of nuclear power are children of the war-like atom. Importance of special growth in a shielded environment is emphasized to exploit fully the advantages of nuclear power. Nuclear power reactors must be safe for their assimilation into society from the points of view of both technology and social psychology. ISR/ISER is identified as a missing link in the development of nuclear power reactors from this perspective and advocated for international development and utilization, being unleashed from the concerns of politicization, safety, and proliferation

Instantaneous measurement of the internal temperature in lithium-ion rechargeable cells

International Nuclear Information System (INIS)

Srinivasan, Rengaswamy; Carkhuff, Bliss G.; Butler, Michael H.; Baisden, Andrew C.

2011-01-01

We demonstrate, in three different rechargeable lithium-ion cells, the existence of an intrinsic relationship between a cell's internal temperature and a readily measurable electrical parameter, namely the phase shift between an applied sinusoidal current and the resulting voltage. The temperature range examined spanned from -20 to 66 deg. C. The optimum single frequency for the phase measurement is in the 40-100 Hz range, allowing for a measurement time of much less than a second; the phase shift in this range depends predominantly on temperature, and is almost completely independent of the state-of-charge. Literature reports suggest that the observed dependence of the phase shift on temperature arises from the ionic conduction of the so-called solid-electrolyte-interphase layer between the graphite anode and the electrolyte. A meter measuring the phase shift across this interphase is analogous to a thermometer reporting the temperature, thereby providing feedback for rapid corrections of any operating conditions that might lead to the catastrophic destruction of the cell. This level of monitoring and control is distinctly different from the present safety-enabling mechanisms: typically positive thermal coefficient ceramics/plastics, or 'shutdown' separators based on polyethylene that act to often permanently shut down current flow through the cell.

Safe Software for Space Applications: Building on the DO-178 Experience

Science.gov (United States)

Dorsey, Cheryl A.; Dorsey, Timothy A.

2013-09-01

DO-178, Software Considerations in Airborne Systems and Equipment Certification, is the well-known international standard dealing with the assurance of software used in airborne systems [1,2]. Insights into the DO-178 experiences, strengths and weaknesses can benefit the international space community. As DO-178 is an excellent standard for safe software development when used appropriately, this paper provides lessons learned and suggestions for using it effectively.

Design and assembly of a torsion pendulum for the measurement of internal friction at low temperatures

International Nuclear Information System (INIS)

San Juan, J. M.; Gallego, I.; No, M. L.

2001-01-01

In this work we describe the assembly, operation and specifications of an inverted torsion pendulum designed to measure internal friction at low temperatures (from 4.2 K to 500 K). The high precision mechanics allow us to obtain internal friction spectra with low levels of noise from amplitudes as small as 2x10''7. The inertia components of the pendulum have been built with specific materials, so that the resonance frequency of the pendulum can be changed within two orders of magnitude (0.1-10Hz). In addition, the sample can be in situ deformed at any temperature and can be inserted into the pendulum at liquid nitrogen temperature. The operation of the pendulum, all the control p recesses and data acquisition are completely automated. (Author) 4 refs

Internal delensing of Planck CMB temperature and polarization

Energy Technology Data Exchange (ETDEWEB)

Carron, Julien [Department of Physics and Astronomy, University of Sussex, Brighton BN1 9QH (United Kingdom); Lewis, Antony; Challinor, Anthony, E-mail: j.carron@sussex.ac.uk, E-mail: Antony.Lewis@sussex.ac.uk, E-mail: a.d.challinor@ast.cam.ac.uk [Institute of Astronomy and Kavli Institute for Cosmology, Madingley Road, Cambridge, CB3 0HA (United Kingdom)

2017-05-01

We present a first internal delensing of CMB maps, both in temperature and polarization, using the public foreground-cleaned (SMICA) Planck 2015 maps. After forming quadratic estimates of the lensing potential, we use the corresponding displacement field to undo the lensing on the same data. We build differences of the delensed spectra to the original data spectra specifically to look for delensing signatures. After taking into account reconstruction noise biases in the delensed spectra, we find an expected sharpening of the power spectrum acoustic peaks with a delensing efficiency of 29 % ( TT ) 25 % ( TE ) and 22 % ( EE ). The detection significance of the delensing effects is very high in all spectra: 12 σ in EE polarization; 18 σ in TE ; and 20 σ in TT . The null hypothesis of no lensing in the maps is rejected at 26 σ. While direct detection of the power in lensing B -modes themselves is not possible at high significance at Planck noise levels, we do detect (at 4.5 σ (under the null hypothesis)) delensing effects in the B -mode map, with 7 % reduction in lensing power. Our results provide a first demonstration of polarization delensing, and generally of internal CMB delensing, and stand in agreement with the baseline ΛCDM Planck 2015 cosmology expectations.

The SafeCOP ECSEL Project: Safe Cooperating Cyber-Physical Systems Using Wireless Communication

DEFF Research Database (Denmark)

Pop, Paul; Scholle, Detlef; Hansson, Hans

2016-01-01

This paper presents an overview of the ECSEL project entitled "Safe Cooperating Cyber-Physical Systems using Wireless Communication" (SafeCOP), which runs during the period 2016 -- 2019. SafeCOP targets safety-related Cooperating Cyber-Physical Systems (CO-CPS) characterised by use of wireless...... detection of abnormal behaviour, triggering if needed a safe degraded mode. SafeCOP will also develop methods and tools, which will be used to produce safety assurance evidence needed to certify cooperative functions. SafeCOP will extend current wireless technologies to ensure safe and secure cooperation...

Regulatory requirements on management of radioactive material safe transport in China

International Nuclear Information System (INIS)

Chu, C.

2016-01-01

Since 1980s, the IAEA Regulation for safe transport of radioactive material was introduced into China; the regulatory system of China began with international standards, and walked towards the institutionalized. In 2003 the National People’s Congress (NPC) promulgated “the Act on the Prevention of Radioactive Pollution of the People's Republic of China”. In 2009 “Regulation for the Safe Transport of Radioactive Material” (Referred to “Regulation”) was promulgated by the State Council. Subsequently, the National Nuclear Safety Administration (NNSA) began to formulate executive detailed department rules, regulations guidelines and standards. The present system of acts, regulations and standards on management of safe transport of radioactive material in China and future planning were introduced in this paper. Meanwhile, the paper described the specific administration requirements of the Regulation on classification management of radioactive materials, license management of transport packaging including design, manufacture and use, licensing management of transport activities and the provisions of illegal behaviors arising in safe transport of radioactive material. (author)

Inherently safe nuclear-driven internal combustion engines

International Nuclear Information System (INIS)

Alesso, P.; Chow, Tze-Show; Condit, R.; Heidrich, J.; Pettibone, J.; Streit, R.

1991-01-01

A family of nuclear driven engines is described in which nuclear energy released by fissioning of uranium or plutonium in a prompt critical assembly is used to heat a working gas. Engine performance is modeled using a code that calculates hydrodynamics, fission energy production, and neutron transport self-consistently. Results are given demonstrating a large negative temperature coefficient that produces self-shutoff of energy production. Reduced fission product inventory and the self-shutoff provide inherent nuclear safety. It is expected that nuclear engine reactor units could be scaled from 100 MW on up. 7 refs., 3 figs

Safe Kids Worldwide

Science.gov (United States)

... Blog Videos Newsletter facebook twitter instagram pinterest gplus youtube Search Menu Why It Matters Who We Are What We Do Find Your Safe Kids Safe Kids Day Main menu Keeping All Kids Safe Safety Tips Get Involved 4 Star Charity Donate Text Burns and Scalds 4 tips ...

Internal and External Temperature Monitoring of a Li-Ion Battery with Fiber Bragg Grating Sensors

Directory of Open Access Journals (Sweden)

Susana Novais

2016-08-01

Full Text Available The integration of fiber Bragg grating (FBG sensors in lithium-ion cells for in-situ and in-operando temperature monitoring is presented herein. The measuring of internal and external temperature variations was performed through four FBG sensors during galvanostatic cycling at C-rates ranging from 1C to 8C. The FBG sensors were placed both outside and inside the cell, located in the center of the electrochemically active area and at the tab-electrode connection. The internal sensors recorded temperature variations of 4.0 ± 0.1 °C at 5C and 4.7 ± 0.1 °C at 8C at the center of the active area, and 3.9 ± 0.1 °C at 5C and 4.0 ± 0.1 °C at 8C at the tab-electrode connection, respectively. This study is intended to contribute to detection of a temperature gradient in real time inside a cell, which can determine possible damage in the battery performance when it operates under normal and abnormal operating conditions, as well as to demonstrate the technical feasibility of the integration of in-operando microsensors inside Li-ion cells.

Safe and reliable solutions for Internet application in power sector

International Nuclear Information System (INIS)

Eichelburg, W. K.

2004-01-01

The requirements for communication of various information systems (control systems, EMS, ERP) continually increase. Internet is prevailingly a Universal communication device for interconnection of the distant systems at the present. However, the communication with the outside world is important, the internal system must be protected safely and reliably. The goal of the article is to inform the experienced participants with the verified solutions of the safe and reliable Internet utilization for interconnection of control systems on the superior level, the distant management, the diagnostic and for interconnection of information systems. An added value is represented by the solutions using Internet for image and sound transmission. (author)

Safe shutdown analysis for submerged equipment inside containment

International Nuclear Information System (INIS)

Song, Dong Soo; Lee, Seung Chan; Yoon, Duk Joo; Ha, Sang Jun

2017-01-01

The purpose of the paper is to analyze internal flooding effects on the submerged safety-related components inside containment building. Safe shutdown analysis has been performed based on the criteria, assumptions and guideline provided in ANSI/ANS-56.11-1988 and ANSI/ANS-58.11-1988. Flooding can be postulated from a failure of several systems located inside the containment. Loss of coolant accident (LOCA), Feed water line break (FWLB), and other pipe breaks/cracks are assumed. The worst case flooding scenario is a large break LOCA. The maximum flood level for a large break LOCA is calculated based on the combined inventory of the reactor coolant system, the three accumulators, the boron injection tank (BIT), the chemical additive tank (CAT), and the refueling water storage tank (RWST) flooding the containment. The maximum flood level that could occur from all of the water which is available in containment is 2.3 m from the base elevation. A detailed flooding analysis for the components has been performed to demonstrate that internal flooding resulting from a postulated initiating event does not cause the loss of equipment required to achieve and maintain safe shutdown of the plant, emergency core cooling capability, or equipment whose failure could result in unacceptable offsite radiological consequences. The flood height can be calculated as h = (dh/dt) x (t-t 0 ) + h 0 , where h = time dependent flood height and subscript 0 means the initial value and height slope dh/dt. In summary, the submerged components inside containment are acceptable because they complete the mission of safety injection (SI) prior to submeregency or have no safe shutdown function including containment isolation during an accident. (author)

"Same Room, Safe Place".

Science.gov (United States)

Keene Woods, Nikki

2017-04-01

There are many different professional stances on safe sleep and then there is the reality of caring for a newborn. There is a debate among professionals regarding safe sleep recommendations. The continum of recommendations vary from the American Academy of Pediatrics (AAP) Safe Sleep Guidelines to the bed-sharing recommendations from the Mother-Baby Behavioral Sleep Laboratory. The lack of consistent and uniform safe sleep recommendations from health professionals has been confusing for families but has more recently raised a real professional ethical dilemma. Despite years of focused safe sleep community education and interventions, sleep-related infant deaths are on the rise in many communities. This commentary calls for a united safe sleep message from all health professionals to improve health for mothers and infants most at-risk, "Same Room, Safe Place."

Internal drainage of infected pancreatic pseudocysts: safe or sorry?

NARCIS (Netherlands)

Boerma, D.; van Gulik, T. M.; Obertop, H.; Gouma, D. J.

1999-01-01

BACKGROUND: External drainage is the traditional surgical therapy for infected pancreatic pseudocyst, although associated with high morbidity and mortality rates. In this study it was determined whether internal drainage is feasible with acceptable postoperative morbidity and recurrence rates.

Forcing, feedback and internal variability in global temperature trends.

Science.gov (United States)

Marotzke, Jochem; Forster, Piers M

2015-01-29

Most present-generation climate models simulate an increase in global-mean surface temperature (GMST) since 1998, whereas observations suggest a warming hiatus. It is unclear to what extent this mismatch is caused by incorrect model forcing, by incorrect model response to forcing or by random factors. Here we analyse simulations and observations of GMST from 1900 to 2012, and show that the distribution of simulated 15-year trends shows no systematic bias against the observations. Using a multiple regression approach that is physically motivated by surface energy balance, we isolate the impact of radiative forcing, climate feedback and ocean heat uptake on GMST--with the regression residual interpreted as internal variability--and assess all possible 15- and 62-year trends. The differences between simulated and observed trends are dominated by random internal variability over the shorter timescale and by variations in the radiative forcings used to drive models over the longer timescale. For either trend length, spread in simulated climate feedback leaves no traceable imprint on GMST trends or, consequently, on the difference between simulations and observations. The claim that climate models systematically overestimate the response to radiative forcing from increasing greenhouse gas concentrations therefore seems to be unfounded.

Convective cells of internal gravity waves in the earth's atmosphere with finite temperature gradient

Directory of Open Access Journals (Sweden)

O. Onishchenko

2013-03-01

Full Text Available In this paper, we have investigated vortex structures (e.g. convective cells of internal gravity waves (IGWs in the earth's atmosphere with a finite vertical temperature gradient. A closed system of nonlinear equations for these waves and the condition for existence of solitary convective cells are obtained. In the atmosphere layers where the temperature decreases with height, the presence of IGW convective cells is shown. The typical parameters of such structures in the earth's atmosphere are discussed.

An internal reference model-based PRF temperature mapping method with Cramer-Rao lower bound noise performance analysis.

Science.gov (United States)

Li, Cheng; Pan, Xinyi; Ying, Kui; Zhang, Qiang; An, Jing; Weng, Dehe; Qin, Wen; Li, Kuncheng

2009-11-01

The conventional phase difference method for MR thermometry suffers from disturbances caused by the presence of lipid protons, motion-induced error, and field drift. A signal model is presented with multi-echo gradient echo (GRE) sequence using a fat signal as an internal reference to overcome these problems. The internal reference signal model is fit to the water and fat signals by the extended Prony algorithm and the Levenberg-Marquardt algorithm to estimate the chemical shifts between water and fat which contain temperature information. A noise analysis of the signal model was conducted using the Cramer-Rao lower bound to evaluate the noise performance of various algorithms, the effects of imaging parameters, and the influence of the water:fat signal ratio in a sample on the temperature estimate. Comparison of the calculated temperature map and thermocouple temperature measurements shows that the maximum temperature estimation error is 0.614 degrees C, with a standard deviation of 0.06 degrees C, confirming the feasibility of this model-based temperature mapping method. The influence of sample water:fat signal ratio on the accuracy of the temperature estimate is evaluated in a water-fat mixed phantom experiment with an optimal ratio of approximately 0.66:1. (c) 2009 Wiley-Liss, Inc.

9th international conference on high-temperature reactors - coal and nuclear energy for electricity and gas generation

International Nuclear Information System (INIS)

Kelber, G.

1987-01-01

The site of the high-temperatur reactor in the Ruhr region neighbouring on a coal-fired power plant is not accidental. The potential of the high-temperature reactor as a central plant element for the supply of heat for heating purposes and process heat covers also the possibility of coal gasification and liquefaction. Therefore the high-temperature reactor is, in the long term, a ray of hope for the coal region, able to compensate for the production-related competitive disadvantages of local coal. It can contribute to guaranteeing in the long term the task of German hard coal as an essential pillar of our energy supply. The VGB as a technical association of thermal power plant operators is particularly committed to the integration of coal and nuclear energy. Within the bounds of its possibilities, it will contribute to promoting the safe and environmentally beneficial generation of electricity from the two primary energy sources. (orig./DG) [de

Low temperature internal friction in La75Al20Si5 metallic glass

International Nuclear Information System (INIS)

Zolotukhin, I.V.; Kalinin, Yu.E.

1991-01-01

Results of investigation of temperature dependence of internal friction (IF) in amorphous alloy La 75 Al 20 Si 5 are presented. The amorphous state was atteined by quenching from liquid melt at a rate of 10 5 -10 6 K/s. Two IF maxima at Q -1 (T) dependence are observed at the temperatures of 185 and 230 K. Increase in the frequency of mechanical vibrations results in the shift of IF maxima to the side of high temperatures, which indicates their relaxation origin. The first peak of IF in the studied alloy La 75 Al 20 Si 5 is in all probability related to reorientation of chemical bonds La-La and La-Al. The maximum at T∼230 K is related to the switching of La-Si chemical bonds

International Law governing the Safe and Peaceful Uses of Nuclear Energy

International Nuclear Information System (INIS)

Jankowitsch-Prevor, O.

2002-01-01

1. The International Governmental Institutions. History and mandates: IAEA, OECD/NEA, EURATOM. 2. International Treaties and Conventions: The Peaceful Uses of Nuclear Energy: Commitment and Verification (the NPT, Safeguards Agreements with the IAEA, The Additional protocol, Regional Non-proliferation Treaties); the Physical protection of Nuclear Material (Convention on the Physical Protection of Nuclear Material); Civil Liability for Nuclear Damage (Vienna Convention on the Civil Liability for Nuclear Damage, Protocol to Amend the Vienna Convention, Paris Convention on Civil Liability, Joint Protocol relating to the Application of the Vienna Convention and the Paris Convention, Convention on Supplementary compensation for Nuclear Damage); In case of Nuclear Accident: Notification and Assistance (Convention on Early Notification of a Nuclear Accident, Convention on Assistance in the case of a Nuclear Accident or Radiological Emergency); International Law Governing Nuclear Safety (Nuclear Safety Convention, Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management). 3. Relationship between International and National Law

Development and design of an integrated information management system for safe management of radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Son, Dong Chan; Hong, Suk Young; An, Kyoung Il [Daesang Information Technology Co., Ltd., Seoul (Korea, Republic of)

2004-05-15

An integrated data management system for the safe management of radioactive waste and spent fuel in Korea is developed to collect basic information, provide the framework for national regulation, and improve national competition and efficiency in the management of radioactive waste and spent fuel. This system can also provide public access to information such as a statistical graphs and integrated data from various waste generators to meet increased public needs and interests. Objectives can be summarized as; the five principles (independence, openness, clearance, efficiency and reliance) of safety regulation can be realized. Public understanding and reliance on the safety of spent fuel and radioactive waste management can be promoted by providing reliable information. Ensure an openness within the international nuclear community and efficiently support international agreements among contracting parties by operating safe and efficient management of spent fuel and radioactive waste (IAEA joint convention on the safety of spent fuel management and on the safety of radioactive waste management). The system can compensate for the imperfections In safe regulation of radioactive waste and spent fuel management related to waste generation, storage and disposal, and make it possible to holistic control. Re-organize the basic framework of KINS's intermediate and long term research organization and trends, regarding waste management policy is to integrate safe management and unit safe disposal.

Development and design of an integrated information management system for safe management of radioactive waste

International Nuclear Information System (INIS)

Son, Dong Chan; Hong, Suk Young; An, Kyoung Il

2004-05-01

An integrated data management system for the safe management of radioactive waste and spent fuel in Korea is developed to collect basic information, provide the framework for national regulation, and improve national competition and efficiency in the management of radioactive waste and spent fuel. This system can also provide public access to information such as a statistical graphs and integrated data from various waste generators to meet increased public needs and interests. Objectives can be summarized as; the five principles (independence, openness, clearance, efficiency and reliance) of safety regulation can be realized. Public understanding and reliance on the safety of spent fuel and radioactive waste management can be promoted by providing reliable information. Ensure an openness within the international nuclear community and efficiently support international agreements among contracting parties by operating safe and efficient management of spent fuel and radioactive waste (IAEA joint convention on the safety of spent fuel management and on the safety of radioactive waste management). The system can compensate for the imperfections In safe regulation of radioactive waste and spent fuel management related to waste generation, storage and disposal, and make it possible to holistic control. Re-organize the basic framework of KINS's intermediate and long term research organization and trends, regarding waste management policy is to integrate safe management and unit safe disposal

Estimation of Surface Temperature and Heat Flux by Inverse Heat Transfer Methods Using Internal Temperatures Measured While Radiantly Heating a Carbon/Carbon Specimen up to 1920 F

Science.gov (United States)

Pizzo, Michelle; Daryabeigi, Kamran; Glass, David

2015-01-01

The ability to solve the heat conduction equation is needed when designing materials to be used on vehicles exposed to extremely high temperatures; e.g. vehicles used for atmospheric entry or hypersonic flight. When using test and flight data, computational methods such as finite difference schemes may be used to solve for both the direct heat conduction problem, i.e., solving between internal temperature measurements, and the inverse heat conduction problem, i.e., using the direct solution to march forward in space to the surface of the material to estimate both surface temperature and heat flux. The completed research first discusses the methods used in developing a computational code to solve both the direct and inverse heat transfer problems using one dimensional, centered, implicit finite volume schemes and one dimensional, centered, explicit space marching techniques. The developed code assumed the boundary conditions to be specified time varying temperatures and also considered temperature dependent thermal properties. The completed research then discusses the results of analyzing temperature data measured while radiantly heating a carbon/carbon specimen up to 1920 F. The temperature was measured using thermocouple (TC) plugs (small carbon/carbon material specimens) with four embedded TC plugs inserted into the larger carbon/carbon specimen. The purpose of analyzing the test data was to estimate the surface heat flux and temperature values from the internal temperature measurements using direct and inverse heat transfer methods, thus aiding in the thermal and structural design and analysis of high temperature vehicles.

International cooperation on technical support for regulation of safety-related activities on the transformation of the destroyed Chernobyl Nuclear Power Plant Power Unit into an ecologically safe system

International Nuclear Information System (INIS)

Groniov, G.; Kondratiev, S.; Kutina, L.; Bachner, D.; Kuechler, L.; Denver, D.

2010-01-01

The world's most severe nuclear accident destroyed the fourth unit at the Chernobyl nuclear power plant in 1986. In the six months following the accident, a localizing building was erected over the unit to contain the nuclear materials and provide support services for managing the destroyed reactor. Since 1997, an international project which includes both urgent measures for stabilization and safety upgrading as well as long-term measures for transforming the facility into an ecologically safe system has been under way. This paper discusses an important aspect of this project which has been the cooperation amongst the technical support organizations of the Ukrainian regulatory authorities and the technical support from international organizations. (author)

DroidSafe

Science.gov (United States)

2016-12-01

Massachusetts Avenue, Build E19-750 Cambridge , MA 02139-4307 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS...Activity objects illustrating the challenges of points-to and information flow analysis...measure how many malicious flows Droid- Safe was able to detect). As these results illustrate , DroidSafe implements an analysis of unprece- dented

The safe management of sources of radiation: Principles and strategies. INSAG-11. A report by the International Nuclear Safety Advisory Group (Russian Edition)

International Nuclear Information System (INIS)

2015-01-01

The IAEA activities relating to nuclear safety are based upon a number of premises. First and foremost, each Member State bears full responsibility for the safety of its nuclear facilities. States can be advised, but cannot be relieved of this responsibility. Secondly, much can be gained by exchanging experience; lessons learned can prevent accidents. Finally, the image of nuclear safety is international; a serious accident anywhere affects the public view of nuclear power everywhere. With the intention of strengthening its contribution to ensuring safety of nuclear power plants, the IAEA established the International Safety Advisory Group (INSAG), whose duties include serving as a forum for the exchange of information on nuclear safety issues of international significance and formulating commonly shared safety principles. The present report deals with the general principles governing the safety of all sources of radiation and with application of these principles. It intends to show that, at the conceptual level, the distinction traditionally made between nuclear safety and radiation protection is hardly justifiable. It is intended primarily for those non-specialists who need to take decisions about safe management of sources of radiation and who wish to gain a better understanding of the approach followed in managing the safety of these sources

Safe havens in Europe

DEFF Research Database (Denmark)

Paldam, Martin

2013-01-01

Eleven safe havens exist in Europe providing offshore banking and low taxes. Ten of these states are very small while Switzerland is moderately small. All 11 countries are richer than their large neighbors. It is shown that causality is from small to safe haven to wealth, and that theoretically...... equilibriums are likely to exist where a certain regulation is substantially lower in a small country than in its big neighbor. This generates a large capital inflow to the safe havens. The pool of funds that may reach the safe havens is shown to be huge. It is far in excess of the absorptive capacity...... of the safe havens, but it still explains, why they are rich. Microstates offer a veil of anonymity to funds passing through, and Switzerland offers safe storage of funds....

Traveling Safely with Medicines

Science.gov (United States)

... Medications Safely My Medicine List How to Administer Traveling Safely with Medicines Planes, trains, cars – even boats ... your trip, ask your pharmacist about how to travel safely with your medicines. Make sure that you ...

SAFE-3D, Stress Analysis of 3-D Composite Structure by Finite Elements Method

International Nuclear Information System (INIS)

Cornell, D.C.; Jadhav, K.; Crowell, J.S.

1969-01-01

1 - Description of problem or function: SAFE-3D is a finite-element program for the three-dimensional elastic analysis of heterogeneous composite structures. The program uses the following types of finite elements - (1) tetrahedral elements to represent the continuum, (2) triangular plane stress membrane elements to represent inner liner or outer case, and (3) uniaxial tension-compression elements to represent internal reinforcement. The structure can be of arbitrary geometry and have any distribution of material properties, temperatures, surface loadings, and boundary conditions. 2 - Method of solution: The finite-element variational method is used. Equilibrium equations are solved by the alternating component iterative method. 3 - Restrictions on the complexity of the problem - Maxima of: 5000 nodes; 16000 elements. The program cannot be applied to incompressible solids and is not recommended for Poisson's ratio in the range of nu between 0.495 and 0.5

Brain injury in the international multicenter randomized SafeBoosC phase II feasibility trial

DEFF Research Database (Denmark)

Plomgaard, Anne M; Hagmann, Cornelia; Alderliesten, Thomas

2016-01-01

BACKGROUND: Abnormal cerebral perfusion during the first days of life in preterm infants is associated with higher grades of intraventricular hemorrhages and lower developmental score. In SafeBoosC II, we obtained a significant reduction of cerebral hypoxia by monitoring cerebral oxygenation in c...

High-temperature deformation and rupture behavior of internally-pressurized Zircaloy-4 cladding in vacuum and steam enivronments

International Nuclear Information System (INIS)

Chung, H.M.; Garde, A.M.; Kassner, T.F.

1977-01-01

The high-temperature diametral expansion and rupture behavior of Zircaloy-4 fuel-cladding tubes have been investigated in vacuum and steam environments under transient-heating conditions that are of interest in hypothetical loss-of-coolant accident situations in light-water reactors. The effects of internal pressure, heating rate, axial constraint, and localized temperature nonuniformities in the cladding on the maximum circumferential strain have been determined for burst temperatures between approximately 650 and 1350 0 C

Design of a control system for HIRFL-CSRe internal target facility in Lanzhou

International Nuclear Information System (INIS)

Wang Yanyu; Liu Wufeng; Shao Caojie; Lin Feiyu; Zhang Jianchuan; Xiao Wenjun

2010-01-01

It is described in this paper the design of the control system for HIRFL-CSRe internal target facility, in which there are many different kinds of units need to be monitored and controlled. The control system is composed of several subsystems which are designed to control the gas-jet temperature, chamber vacuum, valves and molecular pumps. A human-computer interaction interface is also realized to do the data acquisition, data processing and display. The whole system has been working stably and safely, it fully meets the requirements of physical experiments in the internal target facility. In January of 2010, the first physics experiment of the radioactive electron capture was finished successfully with the aids of this control system. (authors)

Safe Handling of Radioisotopes. 1973 Edition

International Nuclear Information System (INIS)

1973-01-01

Under its Statute the International Atomic Energy Agency is empowered to provide for the application of standards of safety for protection against radiation to its own operations and to operations making use of assistance provided by it or with which it is otherwise directly associated. To this end authorities receiving such assistance are required to observe relevant health and safety measures prescribed by the Agency. As a first step, it was considered an urgent task to provide users of radionuclides with a manual of practice for the safe handling of these substances. The first edition of such a manual was published in 1958 and represented the first of the ''Safety Series'', a series of manuals and codes on health and safety published by the Agency. It was prepared after careful consideration of existing national and international codes of radiation safety by a group of international experts and in consultation with other international bodies. This edition presents the second revision. In response to the suggestion made by some Member States, the term 'radioisotopes' has been changed to 'radionuclides' in the title and, as appropriate, in the text because the term 'radionuclides' includes the radioactive element itself as well as the isotopes. The series of manuals and codes published in the Safety Series and the Technical Reports Series give more complete advice to the user on specialized topics.

Internal Thermal Control System Hose Heat Transfer Fluid Thermal Expansion Evaluation Test Report

Science.gov (United States)

Wieland, P. O.; Hawk, H. D.

2001-01-01

During assembly of the International Space Station, the Internal Thermal Control Systems in adjacent modules are connected by jumper hoses referred to as integrated hose assemblies (IHAs). A test of an IHA has been performed at the Marshall Space Flight Center to determine whether the pressure in an IHA filled with heat transfer fluid would exceed the maximum design pressure when subjected to elevated temperatures (up to 60 C (140 F)) that may be experienced during storage or transportation. The results of the test show that the pressure in the IHA remains below 227 kPa (33 psia) (well below the 689 kPa (100 psia) maximum design pressure) even at a temperature of 71 C (160 F), with no indication of leakage or damage to the hose. Therefore, based on the results of this test, the IHA can safely be filled with coolant prior to launch. The test and results are documented in this Technical Memorandum.

Heat Pipe Reactor Dynamic Response Tests: SAFE-100 Reactor Core Prototype

Science.gov (United States)

Bragg-Sitton, Shannon M.

2005-01-01

The SAFE-I00a test article at the NASA Marshall Space Flight Center was used to simulate a variety of potential reactor transients; the SAFEl00a is a resistively heated, stainless-steel heat-pipe (HP)-reactor core segment, coupled to a gas-flow heat exchanger (HX). For these transients the core power was controlled by a point kinetics model with reactivity feedback based on core average temperature; the neutron generation time and the temperature feedback coefficient are provided as model inputs. This type of non-nuclear test is expected to provide reasonable approximation of reactor transient behavior because reactivity feedback is very simple in a compact fast reactor (simple, negative, and relatively monotonic temperature feedback, caused mostly by thermal expansion) and calculations show there are no significant reactivity effects associated with fluid in the HP (the worth of the entire inventory of Na in the core is .tests, the point kinetics model was based on core thermal expansion via deflection measurements. It was found that core deflection was a strung function of how the SAFE-100 modules were fabricated and assembled (in terms of straightness, gaps, and other tolerances). To remove the added variable of how this particular core expands as compared to a different concept, it was decided to use a temperature based feedback model (based on several thermocouples placed throughout the core).

Safe transport of radioactive material. Second edition

International Nuclear Information System (INIS)

1996-01-01

In 1991, the International Atomic Energy Agency published Training Course Series No. 1 (TCS-1), a training manual that provides in 20 chapters a detailed discussion of the background, philosophy, technical bases and requirements and implementation aspects of the Regulations for the Safe Transport of Radioactive Material. The Transport Regulations are widely implemented by the IAEA's Member States and are also used as the bases for radioactive material transport requirements of modal organisations such as the International Maritime Organization and the International Civil Aviation Organization. This document is a supplement of TCS-1 to provide additional material in the form of learning aids and new exercises, that have been developed with the use of TCS-1 at succeeding IAEA training courses. The learning aids in the first part of the supplement are hitherto unpublished material that provide detailed guidance useful in solving the exercises presented in the second part. Solutions to the exercises are on field at the IAEA Secretariat and are available by arrangement to lectures presenting IAEA training courses. 4 refs, 1 fig., 6 tabs

A Bayesian Retrieval of Greenland Ice Sheet Internal Temperature from Ultra-wideband Software-defined Microwave Radiometer (UWBRAD) Measurements

Science.gov (United States)

Duan, Y.; Durand, M. T.; Jezek, K. C.; Yardim, C.; Bringer, A.; Aksoy, M.; Johnson, J. T.

2017-12-01

The ultra-wideband software-defined microwave radiometer (UWBRAD) is designed to provide ice sheet internal temperature product via measuring low frequency microwave emission. Twelve channels ranging from 0.5 to 2.0 GHz are covered by the instrument. A Greenland air-borne demonstration was demonstrated in September 2016, provided first demonstration of Ultra-wideband radiometer observations of geophysical scenes, including ice sheets. Another flight is planned for September 2017 for acquiring measurements in central ice sheet. A Bayesian framework is designed to retrieve the ice sheet internal temperature from simulated UWBRAD brightness temperature (Tb) measurements over Greenland flight path with limited prior information of the ground. A 1-D heat-flow model, the Robin Model, was used to model the ice sheet internal temperature profile with ground information. Synthetic UWBRAD Tb observations was generated via the partially coherent radiation transfer model, which utilizes the Robin model temperature profile and an exponential fit of ice density from Borehole measurement as input, and corrupted with noise. The effective surface temperature, geothermal heat flux, the variance of upper layer ice density, and the variance of fine scale density variation at deeper ice sheet were treated as unknown variables within the retrieval framework. Each parameter is defined with its possible range and set to be uniformly distributed. The Markov Chain Monte Carlo (MCMC) approach is applied to make the unknown parameters randomly walk in the parameter space. We investigate whether the variables can be improved over priors using the MCMC approach and contribute to the temperature retrieval theoretically. UWBRAD measurements near camp century from 2016 was also treated with the MCMC to examine the framework with scattering effect. The fine scale density fluctuation is an important parameter. It is the most sensitive yet highly unknown parameter in the estimation framework

Internal stresses in steel plate generated by shape memory alloy inserts

International Nuclear Information System (INIS)

Malard, B.; Pilch, J.; Sittner, P.; Davydov, V.; Sedlák, P.; Konstantinidis, K.; Hughes, D.J.

2012-01-01

Graphical abstract: Display Omitted Highlights: ► Thermoresponsive internal stresses introduced into steel by embedding SMA inclusions. ► Neutron strain scanning on steel plate coupons with NiTi inserts at 21 °C and 130 °C. ► Internal stress field in steel evaluated directly from strains and by FE simulation. ► Internal stress generation by SMA insert resistant to thermal and mechanical fatigue. - Abstract: Neutron strain scanning was employed to investigate the internal stress fields in steel plate coupons with embedded prestrained superelastic NiTi shape memory alloy inserts. Strain fields in steel were evaluated at T = 21 °C and 130 °C on virgin coupons as well as on mechanically and thermally fatigued coupons. Internal stress fields were evaluated by direct calculation of principal stress components from the experimentally measured lattice strains as well as by employing an inverse finite element modeling approach. It is shown that if the NiTi inserts are embedded into the elastic steel matrix following a carefully designed technological procedure, the internal stress fields vary with temperature in a reproducible and predictable way. It is estimated that this mechanism of internal stress generation can be safely applied in the temperature range from −20 °C to 150 °C and is relatively resistant to thermal and mechanical fatigue. The predictability and fatigue endurance of the mechanism are of essential importance for the development of future smart metal matrix composites or smart structures with embedded shape memory alloy components.

Taking the moon's internal temperature

International Nuclear Information System (INIS)

Duba, A.G.

1976-01-01

LLL geophysicists were instrumental in resolving a serious discrepancy between lunar magnetic-field data and melting studies of lunar basalts brought back from the Moon by Apollo astronauts. Estimates of the subsurface temperatures, based on lunar electrical conductivity measurements and laboratory experiments, were hundreds of degrees below those given by models using known melting points of various minerals. The work uncovered a basic flaw in previous measurements. New measurements under more realistic conditions brought the electrical-conductivity temperature estimates into agreement with temperatures derived from melting experiments. This same work also contributed to in situ coal gasification studies; to ERDA's dry, hot-rock geothermal effort; and to a program of monitoring for seismic evidence of clandestine nuclear testing. 4 figures

Auto-ignition control in turbocharged internal combustion engines operating with gaseous fuels

International Nuclear Information System (INIS)

Duarte, Jorge; Amador, Germán; Garcia, Jesus; Fontalvo, Armando; Vasquez Padilla, Ricardo; Sanjuan, Marco; Gonzalez Quiroga, Arturo

2014-01-01

Control strategies for auto-ignition control in turbocharged internal combustion engines operating with gaseous fuels are presented. Ambient temperature and ambient pressure are considered as the disturbing variables. A thermodynamic model for predicting temperature at the ignition point is developed, adjusted and validated with a large experimental data-set from high power turbocharged engines. Based on this model, the performance of feedback and feedforward auto-ignition control strategies is explored. A robustness and fragility analysis for the Feedback control strategies is presented. The feedforward control strategy showed the best performance however its implementation entails adding a sensor and new control logic. The proposed control strategies and the proposed thermodynamic model are useful tools for increasing the range of application of gaseous fuels with low methane number while ensuring a safe running in internal combustion engines. - Highlights: • A model for predicting temperature at the ignition point. • Robust PID, modified PID, and feedforward strategies for auto-ignition control. • λ′ were the best set of tuning equations for calculating controller parameters. • Robust PID showed significant improvements in auto-ignition control. • Feedforward control showed the best performance

Safe management of the operating lifetimes of nuclear power plants. INSAG-14. A report by the International Nuclear Safety Advisory Group

International Nuclear Information System (INIS)

2014-01-01

The International Atomic Energy Agency's activities relating to nuclear safety are based upon a number of premises. First and foremost, each Member State bears full responsibility for the safety of its nuclear facilities. States can be advised, but they cannot be relieved of this responsibility. Secondly, much can be gained by exchanging experience; lessons learned can prevent accidents. Finally, the image of nuclear safety is international; a serious accident anywhere affects the public's view of nuclear power everywhere. With the intention of strengthening its contribution to ensuring the safety of nuclear power plants, the IAEA established the International Nuclear Safety Advisory Group (INSAG), whose duties include serving as a forum for the exchange of information on nuclear safety issues of international significance and formulating, where possible, commonly shared safety principles. The present report by INSAG deals with a general approach to the safe management of the operating lifetimes of nuclear power plants. It responds to the concerns about maintaining adequate safety levels at ageing plants, even beyond their design lifetimes. Maintaining adequate safety levels implies first and foremost stringent control of equipment ageing, consistent with the design safety bases of the plants. However, as stated in the 75-INSAG-3 report, 'Basic Safety Principles for Nuclear Power Plants', nuclear safety requires a continuing quest for excellence; this implies enhancinuest for excellence; this implies enhancing the safety levels of operating nuclear power plants as far as reasonably practicable, with due account taken of experience and advancement in knowledge. Moreover, in view of the present situation of the nuclear industry, it may become difficult to maintain adequate competences in many countries with nuclear power programmes. These topics are considered in this latest INSAG report and released to a wider audience

Safe management of the operating lifetimes of nuclear power plants. INSAG-14. A report by the International Nuclear Safety Advisory Group

International Nuclear Information System (INIS)

1999-01-01

The International Atomic Energy Agency's activities relating to nuclear safety are based upon a number of premises. First and foremost, each Member State bears full responsibility for the safety of its nuclear facilities. States can be advised, but they cannot be relieved of this responsibility. Secondly, much can be gained by exchanging experience; lessons learned can prevent accidents. Finally, the image of nuclear safety is international; a serious accident anywhere affects the public's view of nuclear power everywhere. With the intention of strengthening its contribution to ensuring the safety of nuclear power plants, the IAEA established the International Nuclear Safety Advisory Group (INSAG), whose duties include serving as a forum for the exchange of information on nuclear safety issues of international significance and formulating, where possible, commonly shared safety principles. The present report by INSAG deals with a general approach to the safe management of the operating lifetimes of nuclear power plants. It responds to the concerns about maintaining adequate safety levels at ageing plants, even beyond their design lifetimes. Maintaining adequate safety levels implies first and foremost stringent control of equipment ageing, consistent with the design safety bases of the plants. However, as stated in the 75-INSAG-3 report, 'Basic Safety Principles for Nuclear Power Plants', nuclear safety requires a continuing quest for excellence; this implies enhancing the safety levels of operating nuclear power plants as far as reasonably practicable, with due account taken of experience and advancement in knowledge. Moreover, in view of the present situation of the nuclear industry, it may become difficult to maintain adequate competences in many countries with nuclear power programmes. These topics are considered in this latest INSAG report and released to a wider audience

Regulatory control for safe usage of radiation sources in India

International Nuclear Information System (INIS)

Ghosh, P.K.; Sonawane, A.U.

1998-01-01

The widespread applications of radioactive materials and radiation generating equipment in the field of industry, medicine agriculture and research in India necessitated the establishment of an efficient regulatory framework and consequently the Atomic Energy Regulatory Board (AERB) was constituted to exercise regulatory control over the safe usage of the radioactive materials and the radiation generating equipment. The Atomic Energy Act, 1962 and the Radiation Protection Rules, 1971 promulgated under the Act forms the basis of radiation safety in India and Chairman, AERB is the Competent Authority to enforce the regulatory provisions of the Radiation Protection Rules, 1971, for safe use of radiation source in the country. AERB has published a number of documents such as Radiation Surveillance Procedures, Standards, Codes, Guides and Manuals for safe use and handling of radioactive materials and radiation generating equipment. Apart from nuclear fuel cycle documents, these publications pertain to industrial radiography, medical application of radiation, transport of radioactive material, industrial gamma irradiators, X-ray units etc. AERB safety related publications are based on international standards e.g. BSS, IAEA, ICRP, ISO etc. This paper outlines the methodology of regulatory control exercised by AERB for safe use of the radioactive materials and the radiation generating equipment in the country. (author)

The experience of the Republic of Belarus in the field of safe and secure transport of radioactive material

International Nuclear Information System (INIS)

Astashka, R.; Kronava, Z.; Prykhodzka, A.; Tkachonak, I.

2016-01-01

The experience of the safe and secure transport of radioactive material of the Republic of Belarus includes domestic and international movements. Transit is a substantial part of international movements taking into account the location of the country. Legislative and regulatory requirements on safety and security of radioactive material transport being in force in the country include the demands making by such state structures as the Department on Nuclear and Radiation Safety, the Department on supervision for the safe industrial activities, the Ministry of Health of the Republic of Belarus. At the same time response to accidents and security events belongs to the scope of activity of special subdivisions of the Ministry for Emergency Situations and the Ministry of Internal Affairs of the Republic of Belarus. For safety purposes all the above-mentioned structures are executing their duties in close collaboration with each other and are following the IAEA safety and security recommendations. The regulatory infrastructure concerning the safe and secure transport of radioactive material of the Republic of Belarus is the subject of the contributed paper. (author)

Thermohydraulic design of saturated temperature capsule for IASCC irradiation test

International Nuclear Information System (INIS)

Ide, Hiroshi; Matsui, Yoshinori; Itabashi, Yukio

2002-10-01

An advanced water chemistry controlled irradiation research device is being developed in JAERI, to perform irradiation tests for irradiation assisted stress corrosion cracking (IASCC) research concerned with aging of LWR. This device enables the irradiation tests under the water chemistry condition and the temperature, which simulate the conditions for BWR core internals. The advanced water chemistry controlled irradiation research device is composed of saturated temperature capsule inserted into the JMTR core and the water chemistry control unit installed in the reactor building. Regarding the saturated temperature capsule, the Thermohydraulic design of capsule structure was done, aimed at controlling the specimen's temperature, feeding water velocity on specimen's surface to the environment of BWR nearer. As the result of adopting the new capsule structure based on the design study, it was found out that feeding water velocity at the surface of specimen's is increased to about 10 times as much as before, and nuclear heat generated in the capsule components can be removed safely even in the abnormal event such as the case of loss of feeding water. (author)

Thermohydraulic design of saturated temperature capsule for IASCC irradiation test

Energy Technology Data Exchange (ETDEWEB)

Ide, Hiroshi; Matsui, Yoshinori; Itabashi, Yukio [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment] [and others

2002-10-01

An advanced water chemistry controlled irradiation research device is being developed in JAERI, to perform irradiation tests for irradiation assisted stress corrosion cracking (IASCC) research concerned with aging of LWR. This device enables the irradiation tests under the water chemistry condition and the temperature, which simulate the conditions for BWR core internals. The advanced water chemistry controlled irradiation research device is composed of saturated temperature capsule inserted into the JMTR core and the water chemistry control unit installed in the reactor building. Regarding the saturated temperature capsule, the Thermohydraulic design of capsule structure was done, aimed at controlling the specimen's temperature, feeding water velocity on specimen's surface to the environment of BWR nearer. As the result of adopting the new capsule structure based on the design study, it was found out that feeding water velocity at the surface of specimen's is increased to about 10 times as much as before, and nuclear heat generated in the capsule components can be removed safely even in the abnormal event such as the case of loss of feeding water. (author)

The recommended Threshold Limit Values for heat exposure fail to maintain body core temperature within safe limits in older working adults.

Science.gov (United States)

Lamarche, Dallon T; Meade, Robert D; D'Souza, Andrew W; Flouris, Andreas D; Hardcastle, Stephen G; Sigal, Ronald J; Boulay, Pierre; Kenny, Glen P

2017-09-01

temperature from exceeding 38°C in older workers. Furthermore, a stable core temperature was not achieved within safe limits (i.e., ≤38°C) indicating that the TLV® guidelines may not adequately protect all individuals during work in hot conditions.

A Flexible Three-in-One Microsensor for Real-Time Monitoring of Internal Temperature, Voltage and Current of Lithium Batteries.

Science.gov (United States)

Lee, Chi-Yuan; Peng, Huan-Chih; Lee, Shuo-Jen; Hung, I-Ming; Hsieh, Chien-Te; Chiou, Chuan-Sheng; Chang, Yu-Ming; Huang, Yen-Pu

2015-05-19

Lithium batteries are widely used in notebook computers, mobile phones, 3C electronic products, and electric vehicles. However, under a high charge/discharge rate, the internal temperature of lithium battery may rise sharply, thus causing safety problems. On the other hand, when the lithium battery is overcharged, the voltage and current may be affected, resulting in battery instability. This study applies the micro-electro-mechanical systems (MEMS) technology on a flexible substrate, and develops a flexible three-in-one microsensor that can withstand the internal harsh environment of a lithium battery and instantly measure the internal temperature, voltage and current of the battery. Then, the internal information can be fed back to the outside in advance for the purpose of safety management without damaging the lithium battery structure. The proposed flexible three-in-one microsensor should prove helpful for the improvement of lithium battery design or material development in the future.

Elastic modulus and internal friction of SOFC electrolytes at high temperatures under controlled atmospheres

Science.gov (United States)

Kushi, Takuto; Sato, Kazuhisa; Unemoto, Atsushi; Hashimoto, Shinichi; Amezawa, Koji; Kawada, Tatsuya

2011-10-01

Mechanical properties such as Young's modulus, shear modulus, Poisson's ratio and internal friction of conventional electrolyte materials for solid oxide fuel cells, Zr0.85Y0.15 O1.93 (YSZ), Zr0.82Sc0.18O1.91 (ScSZ), Zr0.81Sc0.18Ce0.01O2-δ (ScCeSZ), Ce0.9Gd0.1O2-δ (GDC), La0.8Sr0.2Ga0.8Mg0.15Co0.05O3-δ (LSGMC), La0.8Sr0.2Ga0.8Mg0.2O3-δ (LSGM), were evaluated by a resonance method at temperatures from room temperature to 1273 K in various oxygen partial pressures. The Young's modulus of GDC gradually decreased with increasing temperature in oxidizing conditions. The Young's moduli of the series of zirconia and lanthanum gallate based materials drastically decreased in an intermediate temperature range and increased slightly with increasing temperature at higher temperatures. The Young's modulus of GDC considerably decreased above 823 K in reducing atmospheres in response to the change of oxygen nonstoichiometry. However, temperature dependences of the Young's moduli of ScCeSZ and LSGMC in reducing atmospheres did not show any significant differences with those in oxidizing atmospheres.

Influence of the choice of internal temperatures on the composition of CxHyOzNt plasmas out of thermodynamic equilibrium: Application to CH2 plasma

International Nuclear Information System (INIS)

Koalaga, Zacharie

2002-01-01

The purpose of this paper is to study the influence of the choice of internal temperatures on the composition of C x H y O z N t plasmas out of thermodynamic equilibrium. The numerical calculation is specially performed for CH 2 plasma in the pressure range 0.1-1 MPa and for the electron temperature range 5000-30 000 K. Precisely, the investigation of this plasma allows one to show that the choice of internal temperatures can have more influence on plasma composition than the choice of the form of the two-temperature Saha and Guldberg-Waage laws. Indeed, for one of the supposed hypotheses, it is observed that the two forms of the two-temperature system used here can give the same equilibrium composition by uncoupling the excitation temperature of the diatomic and the monatomic species. Great attention must then be given to the adopted hypothesis for internal temperature and not only to the form of the two temperature system used. An accurate comparison between the two models requires the measurement of plasma parameters such as the various internal temperatures and the species concentration. Therefore, we have also carried out an analysis of the potential experimental diagnostics of these plasma parameters. Such diagnostics can help to test and validate theoretical models

An international nuclear safety regime

International Nuclear Information System (INIS)

Rosen, M.

1995-01-01

For all the parties involved with safe use of nuclear energy, the opening for signature of the 'Convention on Nuclear Safety' (signed by 60 countries) and the ongoing work to prepare a 'Convention on Radioactive Waste Safety' are particularly important milestones. 'Convention on Nuclear Safety' is the first legal instrument that directly addresses the safety of nuclear power plants worldwide. The two conventions are only one facet of international cooperation to enhance safety. A review of some cooperative efforts of the past decades, and some key provisions of the new safety conventions, presented in this paper, show how international cooperation is increasing nuclear safety worldwide. The safety philosophy and practices involved with legal framework for the safe use of nuclear power will foster a collective international involvement and commitment. It will be a positive step towards increasing public confidence in nuclear power

Burst pressure of super duplex stainless steel pipes subject to combined axial tension, internal pressure and elevated temperature

International Nuclear Information System (INIS)

Lasebikan, B.A.; Akisanya, A.R.

2014-01-01

The burst pressure of super duplex stainless steel pipe is measured under combined internal pressure, external axial tension and elevated temperature up to 160 °C. The experimental results are compared with existing burst pressure prediction models. Existing models are found to provide reasonable estimate of the burst pressure at room temperature but significantly over estimate the burst pressure at elevated temperature. Increasing externally applied axial stress and elevated temperature reduces the pressure capacity. - Highlights: • The burst pressure of super duplex steel is measured under combined loading. • Effect of elevated temperature on burst pressure is determined. • Burst pressure decreases with increasing temperature. • Existing models are reliable at room temperature. • Burst strength at elevated temperature is lower than predictions

SAFE Newsletter

OpenAIRE

2013-01-01

The Center of Excellence SAFE – “Sustainable Architecture for Finance in Europe” – is a cooperation of the Center for Financial Studies and Goethe University Frankfurt. It is funded by the LOEWE initiative of the State of Hessen (Landes-Offensive zur Entwicklung wissenschaftlich-ökonomischer Exzellenz). SAFE brings together more than 40 professors and just as many junior researchers who are all dedicated to conducting research in support of a sustainable financial architecture. The Center has...

Safe handling of plutonium: a panel report

Energy Technology Data Exchange (ETDEWEB)

1974-01-01

This guide results from a meeting of a Panel of Experts held by the International Atomic Energy Agency on 8 to 12 November 1971. It is directed to workers in research laboratories handling plutonium in gram amounts. Contents: aspects of the physical and chemical properties of plutonium; metabolic features of plutonium; facility design features for safe handling of plutonium (layout of facility, working zones, decontamination room, etc.); glove boxes; health surveillance (surveillance of environment and supervision of workers); emergencies; organization. Annexes: types of glove boxes; tables; mobile ..cap alpha.. air sampler; aerosol monitor; bio-assay limits of detection; examples of contamination control monitors.

Communication of 10 June 2009 received from the Permanent Mission of the United Kingdom with regard to the International Nuclear Fuel Supply Conference: Securing safe access to peaceful power

International Nuclear Information System (INIS)

2009-01-01

The Secretariat has received a communication dated 10 June 2009 from the Permanent Mission of the United Kingdom of Great Britain and Northern Ireland, attaching a note from the United Kingdom and the final remarks of the Chairman of the International Nuclear Fuel Supply Conference: Securing safe access to peaceful power, held in London on 17 and 18 March 2009. As requested in that communication, the note and final remarks are herewith circulated for the information of Member States

Safe and efficient operation of multistage cold compressor systems

International Nuclear Information System (INIS)

Kauschke, M.; Haberstroh, C.; Quack, H.

1996-01-01

Large refrigeration rates in the temperature range of super fluid helium can only be obtained with the help of centrifugal cold compressors. For the large 2 K systems, four compression stages are necessary to reach atmospheric pressure. Centrifugal cold compressors are quite sensitive to mass flow and suction temperature variations; but these have to be expected in a real system. The first step in the systems design is to find safe and efficient quasi-stationary modes of operation. The system which is being proposed for the TESLA refrigerators relies on two features. The first is to allow the room temperature screw compressor, downstream of the cold compressors to work occasionally with a subatmospheric suction pressure. The second is to stabilize the suction temperature of the third stage of compression at about 10 K. With these features it is possible, that in all modes of operation all four compressor stages operate exactly at their design point

A Flexible Three-in-One Microsensor for Real-Time Monitoring of Internal Temperature, Voltage and Current of Lithium Batteries

Directory of Open Access Journals (Sweden)

Chi-Yuan Lee

2015-05-01

Full Text Available Lithium batteries are widely used in notebook computers, mobile phones, 3C electronic products, and electric vehicles. However, under a high charge/discharge rate, the internal temperature of lithium battery may rise sharply, thus causing safety problems. On the other hand, when the lithium battery is overcharged, the voltage and current may be affected, resulting in battery instability. This study applies the micro-electro-mechanical systems (MEMS technology on a flexible substrate, and develops a flexible three-in-one microsensor that can withstand the internal harsh environment of a lithium battery and instantly measure the internal temperature, voltage and current of the battery. Then, the internal information can be fed back to the outside in advance for the purpose of safety management without damaging the lithium battery structure. The proposed flexible three-in-one microsensor should prove helpful for the improvement of lithium battery design or material development in the future.

Safe and reliable solutions for Internet application in power sector. SAT automation

International Nuclear Information System (INIS)

Eichelburg, W. K.

2004-01-01

The requirements for communication of various information systems (control systems, EMS, ERP) continually increase. Internet is prevailingly a Universal communication device for interconnection of the distant systems at the present. However, the communication with the outside world is important, the internal system must be protected safely and reliably. The goal of the article is to inform the experienced participants with the verified solutions of the safe and reliable Internet utilization for interconnection of control systems on the superior level, the distant management, the diagnostic and for interconnection of information systems. An added value is represented by the solutions using Internet for image and sound transmission. (author)

Sample environment for neutron scattering measurements of internal stresses in engineering materials in the temperature range of 6 K to 300 K.

Science.gov (United States)

Kirichek, O; Timms, J D; Kelleher, J F; Down, R B E; Offer, C D; Kabra, S; Zhang, S Y

2017-02-01

Internal stresses in materials have a considerable effect on material properties including strength, fracture toughness, and fatigue resistance. The ENGIN-X beamline is an engineering science facility at ISIS optimized for the measurement of strain and stress using the atomic lattice planes as a strain gauge. Nowadays, the rapidly rising interest in the mechanical properties of engineering materials at low temperatures has been stimulated by the dynamic development of the cryogenic industry and the advanced applications of the superconductor technology. Here we present the design and discuss the test results of a new cryogenic sample environment system for neutron scattering measurements of internal stresses in engineering materials under a load of up to 100 kN and in the temperature range of 6 K to 300 K. Complete cooling of the system starting from the room temperature down to the base temperature takes around 90 min. Understanding of internal stresses in engineering materials at cryogenic temperatures is vital for the modelling and designing of cutting-edge superconducting magnets and other superconductor based applications.

International Space Station Temperature and Humidity Control Subsystem Verification for Node 1

Science.gov (United States)

Williams, David E.

2007-01-01

The International Space Station (ISS) Node 1 Environmental Control and Life Support (ECLS) System is comprised of five subsystems: Atmosphere Control and Supply (ACS), Atmosphere Revitalization (AR), Fire Detection and Suppression (FDS), Temperature and Humidity Control (THC), and Water Recovery and Management (WRM). This paper provides a summary of the nominal operation of the Node 1 THC subsystem design. The paper will also provide a discussion of the detailed Element Verification methodologies for nominal operation of the Node 1 THC subsystem operations utilized during the Qualification phase.

Adoption of the B2SAFE EUDAT replication service by the EPOS community

Science.gov (United States)

Cacciari, Claudio; Fares, Massimo; Fiameni, Giuseppe; Michelini, Alberto; Danecek, Peter; Wittenburg, Peter

2014-05-01

B2SAFE is the EUDAT service for moving and replicating data between sites and storage systems for different purposes. The goal of B2SAFE is to keep the data from a repository safe by replicating it across different geographical and administrative zones according to a set of well-defined policies. It is also a way to store large volumes of data permanently at those sites which are providing powerful on-demand data analysis facilities. In particular, B2SAFE operates on the domain of registered data where data objects are referable via persistent identifiers (PIDs). B2SAFE is more than just copying data because the PIDs must be carefully managed when data objects are moved or replicated. The EUDAT B2SAFE Service offers functionality to replicate datasets across different data centres in a safe and efficient way while maintaining all information required to easily find and query information about the replica locations. The information about the replica locations and other important information is stored in PID records, each managed in separate administrative domains. The B2SAFE Service is implemented as an iRODS module providing a set of iRODS rules or policies to interface with the EPIC handle API and uses the iRODS middleware to replicate datasets from a source data (or community) centre to a destination data centre. The definition of the dataset(s) to replicate is flexible and up to the communities using the B2SAFE service. While the B2SAFE is internally using the EPIC handle API, communities have the choice to use any PID system they prefer to assign PIDs to their digital objects. A reference to one or more EUDAT B2SAFE PIDs is returned by the B2SAFE service when a dataset is replicated. The presentation will introduce the problem space of B2SAFE, presents the achievements that have been made during the last year for enabling communities to make use of the B2SAFE service, demonstrates a EPOS use cases, outlines the commonalities and differences between the policies

A thermal extrapolation method for the effective temperatures and internal energies of activated ions

Science.gov (United States)

Meot-Ner (Mautner), Michael; Somogyi, Árpád

2007-11-01

The internal energies of dissociating ions, activated chemically or collisionally, can be estimated using the kinetics of thermal dissociation. The thermal Arrhenius parameters can be combined with the observed dissociation rate of the activated ions using kdiss = Athermalexp(-Ea,thermal/RTeff). This Arrhenius-type relation yields the effective temperature, Teff, at which the ions would dissociate thermally at the same rate, or yield the same product distributions, as the activated ions. In turn, Teff is used to calculate the internal energy of the ions and the energy deposited by the activation process. The method yields an energy deposition efficiency of 10% for a chemical ionization proton transfer reaction and 8-26% for the surface collisions of various peptide ions. Internal energies of ions activated by chemical ionization or by gas phase collisions, and of ions produced by desorption methods such as fast atom bombardment, can be also evaluated. Thermal extrapolation is especially useful for ion-molecule reaction products and for biological ions, where other methods to evaluate internal energies are laborious or unavailable.

Search Results | Page 18 | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

Results 171 - 180 of 257 ... ... Safe and Inclusive Cities 1 Apply Safe and Inclusive Cities filter · Technology ... Regional Dialogue on the Information Society Network (Latin ... engaged in international cooperation for development but don't have ... The study's author, Stacie Travers, also carried out four case studies on Canadian ...

Safe Handling of Radioisotopes. Medical Addendum

International Nuclear Information System (INIS)

Hercik, F.; Jammet, H.

1960-01-01

The International Atomic Energy Agency published in 1958 a Manual entitled ''Safe Handling of Radioisotopes'' (Safety Series No. 1 - STI/PUB/1), based on the work of an international panel convened by the Agency. As recommended by that panel and approved by the Agency's Board of Governors, this Addendum has now been prepared, primarily as a supplement to the Manual. It contains information necessary to medical officers concerned with the implementation of the controls given in the Manual. In addition, it is intended to serve as a brief introduction to the medical problems encountered in radiological protection work and to the methods of resolving them. As in the case of the Manual itself, the information given in this Addendum is particularly relevant to the problems encountered by the small user of radioisotopes. Although the basic principles set forth in it apply to all work with radiation sources, the Addendum is not intended to serve as a radiological protection manual for use in reactor installations or large-scale nuclear industry, where more specialized techniques and information are required.

Poly(3-hydroxybutyrate-co-R-3-hydroxyhexanoate) nanoparticles with polyethylenimine coat as simple, safe, and versatile vehicles for cell targeting

DEFF Research Database (Denmark)

Wu, Linping; Wang, Danyang; Parhamifar, Ladan

2014-01-01

A simple and highly safe poly(3-hydroxybutyrate-co-R-3-hydroxyhexanoate) nanoparticulate delivery system that targets different cell types is developed. A sub-cytotoxic level of polyethylenimine coat mediates universal cell targeting. Internalized nanoparticles traffic along endolysosomal compart...... compartments, endoplasmic reticulum and the Golgi complex. Nanoparticles have no detrimental effects on cell morphology and respiration.......A simple and highly safe poly(3-hydroxybutyrate-co-R-3-hydroxyhexanoate) nanoparticulate delivery system that targets different cell types is developed. A sub-cytotoxic level of polyethylenimine coat mediates universal cell targeting. Internalized nanoparticles traffic along endolysosomal...

Safe transport of radioactive material. Second edition

International Nuclear Information System (INIS)

1991-01-01

The transport of radioactive material embraces the carriage of radioisotopes for industrial, medical and research uses, and the movement of waste, in addition to consignments of nuclear fuel cycle material. It has been estimated that between eighteen and thirty-eight million package shipments take place each year. On the recommendation of the Standing Advisory Group on the Safe Transport of Radioactive Material (SAGSTRAM), which enjoys wide representations from the Agency's Member States and international organizations, the Secretariat is preparing a training kit comprising this training manual and complementary visual aids. The kit is intended to be the basis for an extensive course on the subject and can be used in whole or in part for inter-regional, regional and even national training purposes. Member States can thus benefit from the material either through training courses sponsored by the Agency, or, alternatively, organized by themselves. As a step towards achieving that goal, the current training manual was compiled using material from the first Inter-Regional Training Course on the Safe Transport of Radioactive material that was held in co-operation with the Nuclear Power Training Centre of the then Central Electricity Generating Board at Bristol, United Kingdom. This Manual was initially published in 1990. On the recommendation of the Agency's Standing Advisory Group on the Safe Transport of Radioactive Material (SAGSTRAM), the Manual has since been expanded and updated in time for the second Inter-Regional Training Course, that will in 1991 similarly be held in Bristol. Refs, figs, tabs

How safe is safe enough?

International Nuclear Information System (INIS)

Desnoyers, B.; Chanzy, Y.

2004-01-01

The IAEA Regulations for the Safe Transport of Radioactive Material, were historically established with the objective to reduce the probability that persons be exposed to unacceptable doses due to normal operation or accident situations during transport of radioactive material. Based on the International Basic Safety Standards for Protection against Ionizing Radiation (BSS), the definition, which was adopted for an unacceptable dose for an accident situation, is the excess of the maximum dose limits permissible in a single year for the occupational exposure of a worker in the BSS. Concerning the severity of accident situations, it has always be clearly stated that the objective of the tests for demonstrating ability to withstand accident conditions of transport was not to cover every accident condition, but solely most of them. The last available evaluations regarding the rate of accidents which are covered by the standardised accident conditions of transport defined in the IAEA Regulations give a range of about 80%, plus or minus 15% which depends on transport mode and studies. Consequently, slight variations in the capabilities of the packages to meet the specified performance would probably not have significant consequences on the protection level in case of accident. In the assessment of the compliance with the regulations, the tendency of experts, taking advantage of the enhanced performances of computer calculation codes, is to ask more and more calculations, with more and more accuracy, leading to more and more restrictions. Consequently, cost and delay are considerably increased without any evidence of an equivalent effect on the level of protection. This paper will initiate a reflection on the general objectives and principles when implementing the Regulations, in such a way that demonstrations remain cost effective, taking into account evolution of the techniques and a high level of safety

Characterizing high-temperature deformation of internally heated nuclear fuel element simulators

Energy Technology Data Exchange (ETDEWEB)

Belov, A.I.; Fong, R.W.L.; Leitch, B.W.; Nitheanandan, T.; Williams, A., E-mail: alexander.belov@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada)

2016-06-15

The sag behaviour of a simulated nuclear fuel element during high-temperature transients has been investigated in an experiment utilizing an internal indirect heating method. The major motivation of the experiment was to improve understanding of the dominant mechanisms underlying the element thermo-mechanical response under loss-of-coolant accident conditions and to obtain accurate experimental data to support development of 3-D computational fuel element models. The experiment was conducted using an electrically heated CANDU fuel element simulator. Three consecutive thermal cycles with peak temperatures up to ≈1000 {sup o}C were applied to the element. The element sag deflections and sheath temperatures were measured. On heating up to 600 {sup o}C, only minor lateral deflections of the element were observed. Further heating to above 700 {sup o}C resulted in an element multi-rate creep and significant permanent bow. Post-test visual and X-ray examinations revealed a pronounced necking of the sheath at the pellet-to-pellet interface locations. A wall thickness reduction was detected in the necked region that is interpreted as a sheath longitudinal strain localization effect. The sheath cross-sectioning showed signs of a 'hard' pellet-cladding interaction due to the applied cycles. A 3-D model of the experiment was generated using the ANSYS finite element code. As a fully coupled thermal mechanical simulation is computationally expensive, it was deemed sufficient to use the measured sheath temperatures as a boundary condition, and thus an uncoupled mechanical simulation only was conducted. The ANSYS simulation results match the experiment sag observations well up to the point at which the fuel element started cooling down. (author)

Safe Transport of Radioactive Material, Philosophy and Overview

Energy Technology Data Exchange (ETDEWEB)

EL-Shinawy, R M.K. [Radiation Protection Dept., Nuclear Rasearch Center, Atomic Energy Authority, Cairo (Egypt)

2008-07-01

Safe transport of radioactive material regulations issued by IAEA since 1961, provide standards for insuring a high level of safety of people,transport workers, property and environment against radiation, contamination and criticality hazards as well as thermal effects associated with the transport of the radioactive wastes and material. The history ,development, philosophy and scope of these international and national regulations were mentioned as well as the different supporting documents to the regulations for safe transport of radioactive material were identified.The first supporting document , namely TS - G-1.1(ST-2) ,Advisory material is also issued by the IAEA.It contains both the advisory and explanatory materials previously published in safety series Nos 7and 37 and therefore TS-G-1.1 (ST-2) will supersede safety series Nos 7 and 37. The second supporting document namely TS-G-1.2 (ST-3), planning and preparing for emergency response to transport accidents involving radioactive material ,which will supersede safety series No 87. In addition to quality assurance (SS no.113), compliance assurance (SS no. 112), the training manual and others.

Safe Transport of Radioactive Material, Philosophy and Overview

International Nuclear Information System (INIS)

EL-Shinawy, R.M.K.

2008-01-01

Safe transport of radioactive material regulations issued by IAEA since 1961, provide standards for insuring a high level of safety of people,transport workers, property and environment against radiation, contamination and criticality hazards as well as thermal effects associated with the transport of the radioactive wastes and material. The history ,development, philosophy and scope of these international and national regulations were mentioned as well as the different supporting documents to the regulations for safe transport of radioactive material were identified.The first supporting document , namely TS - G-1.1(ST-2) ,Advisory material is also issued by the IAEA.It contains both the advisory and explanatory materials previously published in safety series Nos 7and 37 and therefore TS-G-1.1 (ST-2) will supersede safety series Nos 7 and 37. The second supporting document namely TS-G-1.2 (ST-3), planning and preparing for emergency response to transport accidents involving radioactive material ,which will supersede safety series No 87. In addition to quality assurance (SS no.113), compliance assurance (SS no. 112), the training manual and others

Status of international HTGR [high-temperature gas-cooled reactor] development

International Nuclear Information System (INIS)

Homan, F.J.; Simon, W.A.

1988-01-01

Programs for the development of high-temperature gas-cooled reactor (HTGR) technology over the past 30 years in eight countries are briefly described. These programs have included both government sector and industrial participation. The programs have produced four electricity-producing prototype/demonstration reaactors, two in the United States, and two in the Federal Republic of Germany. Key design parameters for these reactors are compared with the design parameters planned for follow-on commercial-scale HTGRs. The development of HTGR technology has been enhanced by numerous cooperative agreements over the years, involving both government-sponsored national laboratories and industrial participants. Current bilateral cooperative agreements are described. A relatively new component in the HTGR international cooperation is that of multinational industrial alliances focused on supplying commercial-scale HTGR power plants. Current industrial cooperative agreements are briefly discussed

By-pass flows and temperature distribution in a hot gas duct internally insulated by carbon stone

International Nuclear Information System (INIS)

Konuk, A.A.

1979-01-01

A mathematical model has been developed to calculate by-pass flows and temperature distribution in a hot gas duct internally insulated by carbon stone rings. The equations of conservation of mass and momentum are solved for a piping system to obtain axial and radial by-pass velocities. The energy equation is solved next by a marching method to obtain the radial temperature distribution along the duct. The results, although qualitative due to simplifications in the model, are useful to study the effects of duct geometry on its performance. (Author) [pt

Coherent anti-Stokes Raman spectroscopy temperature measurements in an internal combustion engine

Science.gov (United States)

Ball, Don; Driver, H. Steve T.; Hutcheon, Richard J.; Lockett, Russel J.; Robertson, Gerald N.

1994-09-01

Part of a project to investigate the physics and chemistry of alternative fuels in internal combustion engines is reported. Coherent anti-Stokes Raman spectroscopy (CARS) is used to probe the fuel-air mixture in the cylinder of a Richardo E6 variable compression ratio research engine. The laser system comprises a passively Q- switched single-longitudinal-mode frequency-doubled Nd:YAG laser and a broadband dye laser, both with a pulse length of 15 ns. A crankshaft encoder and electronic delay are used to fire the lasers at specified times during the engine cycle, and CARS spectra are acquired using a 0.75 m spectrometer and a 1024 optical multichannel analyzer. Because of the uncertainties associated with collisional narrowing in the theoretical modeling of high-pressure CARS spectra, temperatures are determined by comparing the engine spectra with a library of experimental CARS spectra from a calibrated high-pressure, high- temperature cell. This purely experimental technique is shown to be superior to two theoretical models under the considered conditions, giving temperatures during the compression stroke of the engine with standard deviations of typically 10 K and a possible systematic error of 15 K. Together with pressure records, this information is used as input data for chemical kinetic modeling of the combustion process.

Isoeugenol is an important contact allergen: can it be safely replaced with isoeugenyl acetate?

DEFF Research Database (Denmark)

White, I R; Johansen, Jeanne Duus; Arnau, E G

1999-01-01

The prevalence of contact allergy to the fragrance mix in individuals with eczema is up to 10%. Within the mix, isoeugenol (CAS 97-54-1) is an important individual allergen. Until May 1998, the IFRA (International Fragrance Association) guidelines suggested that isoeugenol could safely be used at...

Temperature oscillations in the upper thermocline region- A case study on internal waves off Kalpeni Island in the southern Arabian Sea

Digital Repository Service at National Institute of Oceanography (India)

Charyulu, R.J.K.; Sarma, Y.V.B.; Sarma, M.S.S.; Rao, L.V.G.

characteristics of the temperature oscillations. The power spectra of temperature fluctuations at 11 depths in the upper thermocline from 80 to 100 m with 2 m interval, were computed for studying the short period internal waves. Power spectra density was higher...

The Safe Routes to School Program in California: An Update

Science.gov (United States)

Chaufan, Claudia; Fox, Patrick

2012-01-01

Despite efforts to combat increasing rates of childhood obesity, the problem is worsening. Safe Routes to School (SRTS), an international movement motivated by the childhood obesity epidemic, seeks to increase the number of children actively commuting (walking or biking) to school by funding projects that remove barriers preventing them from doing so. We summarize the evaluation of the first phase of an ongoing SRTS program in California and discuss ways to enhance data collection. PMID:22515862

International co-operation for safe radioactive waste management

International Nuclear Information System (INIS)

1983-01-01

As a specialised inter-governmental body, NEA pursues three main objectives for its radioactive waste management programme: - The promotion of studies to improve the data base available in support of national programmes. - The support of Research and Development through co-ordination of national activities and promotion of international projects. - An improvement in the general level of understanding of waste management issues and options, particularly in the field of waste disposal. The management of radioactive waste from nuclear activities covers several sequences of complex technical operations. However, as the ultimate objective of radioactive waste management is the disposal of the waste, the largest part of the work programme is directed towards the analysis of disposal options. In addition, NEA is active in various other areas of waste management, such as the treatment and conditioning of waste, the decommissioning of nuclear facilities and the institutional aspects of the long term management of radioactive waste

Low Temperature Catalyst for NH3 Removal

Science.gov (United States)

Monje, Oscar; Melendez, Orlando

2013-01-01

Air revitalization technologies maintain a safe atmosphere inside spacecraft by the removal of C02, ammonia (NH3), and trace contaminants. NH3 onboard the International Space Station (ISS) is produced by crew metabolism, payloads, or during an accidental release of thermal control refrigerant. Currently, the ISS relies on removing NH3 via humidity condensate and the crew wears hooded respirators during emergencies. A different approach to cabin NH3 removal is to use selective catalytic oxidation (SCO), which builds on thermal catalytic oxidation concepts that could be incorporated into the existing TCCS process equipment architecture on ISS. A low temperature platinum-based catalyst (LTP-Catalyst) developed at KSC was used for converting NH3 to H20 and N2 gas by SCO. The challenge of implementing SCO is to reduce formation of undesirable byproducts like NOx (N20 and NO). Gas mixture analysis was conducted using FTIR spectrometry in the Regenerable VOC Control System (RVCS) Testbed. The RVCS was modified by adding a 66 L semi-sealed chamber, and a custom NH3 generator. The effect of temperature on NH3 removal using the LTP-Catalyst was examined. A suitable temperature was found where NH3 removal did not produce toxic NO, (NO, N02) and N20 formation was reduced.

Exhaust Gas Temperature Measurements in Diagnostics of Turbocharged Marine Internal Combustion Engines Part I Standard Measurements

Directory of Open Access Journals (Sweden)

Korczewski Zbigniew

2015-01-01

Full Text Available The article discusses the problem of diagnostic informativeness of exhaust gas temperature measurements in turbocharged marine internal combustion engines. Theoretical principles of the process of exhaust gas flow in turbocharger inlet channels are analysed in its dynamic and energetic aspects. Diagnostic parameters are defined which enable to formulate general evaluation of technical condition of the engine based on standard online measurements of the exhaust gas temperature. A proposal is made to extend the parametric methods of diagnosing workspaces in turbocharged marine engines by analysing time-histories of enthalpy changes of the exhaust gas flowing to the turbocompressor turbine. Such a time-history can be worked out based on dynamic measurements of the exhaust gas temperature, performed using a specially designed sheathed thermocouple.

Are Detox Diets Safe?

Science.gov (United States)

... Safe Videos for Educators Search English Español Are Detox Diets Safe? KidsHealth / For Teens / Are Detox Diets ... seguras las dietas de desintoxicación? What Is a Detox Diet? The name sounds reassuring — everyone knows that ...

How to improve communication for the safe use of medicines?: Discussions on social marketing and patient-tailored approaches at the annual meetings of the WHO Programme for International Drug Monitoring.

Science.gov (United States)

Bahri, Priya; Harrison-Woolrych, Mira

2012-12-01

Over the past decade, the annual meetings of national centres participating in the WHO Programme for International Drug Monitoring have increasingly included discussions on how to improve communication between national pharmacovigilance centres, patients, healthcare professionals, policy makers and the general public, with the aim of promoting the safe use of medicines. At the most recent meetings, working groups were dedicated to discuss possible applications and implementation of social marketing and patient-tailored approaches. This article provides the history and a summary of the recent discussions and recommendations to support progress in this respect at national and global level. Recommendations are made to investigate and pilot these approaches in small-scale projects at national pharmacovigilance centres. Applying elements from the social marketing and patient-tailored approaches to support behaviours of safe medicines use in patients and healthcare professionals should give the pharmacovigilance community new tools to achieve their goal to minimize risks with medicines and improve patient safety.

International certification in developing countries: the role of internal and external institutional pressure.

Science.gov (United States)

Fikru, Mahelet G

2014-11-01

This paper examines the different internal and external institutional factors that affect the decision of businesses in developing countries to adopt international certification (IC). Past studies focus on pressure from international laws, the role of multinationals, and businesses mimicking practices of their counterparts in developed countries. This paper finds that, in addition to these external factors, internal factors may have a significant role. Even though environmental regulation is weak in developing countries, governments do not ignore industrial pollution and casualties. They respond by increasing bureaucratic regulations for businesses and this can affect the decision to adopt IC. Furthermore, internal pressure may come from workers' unions that push for a safe and healthy working environment. Published by Elsevier Ltd.

Safe decommissioning of the Romanian VVR-S research reactor

International Nuclear Information System (INIS)

Garlea, C.; Garlea, I.; Kelerman, C.; Rodna, A.

2002-01-01

The VVR-S Romania research reactor was operated between 1957-1997, at 2 MW nominal power, for research and radioisotopical production. The detailed decommissioning plan was developed between 1995-1998, in the frame of the International Atomic Energy Agency Technical assistance project ROM/9/017. The proposed strategy agreed by the counterpart as well as international experts was stage 1. In 1997, an independent analysis performed by European Commission experts, in the frame of PHARE project PH04.1/1994 was dedicated to the 'Study of Soviet Design Research Reactors', had consolidated the development of the project emphasizing technical options of safe management for radioactive wastes and VVR-S spent fuel. The paper presents the main technical aspects as well as those of social impact, which lead to the establishment of strategy for safe management of decommissioning. Technical analysis of the VVR-S reactor and associated radwaste facilities (Radioactive Waste Treatment Plant - Magurele and National Repository Baita-Bihor) proved the possibility of the classical method utilization for dismantling of the facility and treatment-conditioning-disposal of the arrised wastes in safe conditions. The decommissioning plan at stage 2 has been developed based on radiological safety assessment, evaluation of radwaste inventory (removed as well as preserved on site), cost analysis and environmental impact. Technical data were provided by the R and D programme including neutron calculations and experiments, radiological characterizing (for facility and its influence area), seismic analysis and environmental balance during the operation and after shut down of the reactor. A special chapter is dedicated to regulatory issues concerning the development of decommissioning under nuclear safety. Based on the Fundamental Norms of Radiological Safety, the Regulatory Body defined the clearance levels and safety criteria for the process. The development of National Norms for the

HySafe - The Network of Excellence for Hydrogen Safety

International Nuclear Information System (INIS)

Jordan, T.

2006-01-01

Safety always has been a critical issue for innovations as it influences the economic attractiveness and public acceptance of any new idea. Furthermore, a fair market for trading innovative products has to be based on homogenized legal regulations, which usually refer commonly accepted standards. Ideally, these standards should be the unique outcome of safety assessments, based on profound and concerted pre-normative research work. However, in Europe the research related to hydrogen safety is still fragmented. This was the reason for the European Commission to support the needed integration and focusing of the related efforts with the help of a new instrument, the so-called Networks of Excellence NoE. So, the goal of NoE HySafe is to provide the basis to facilitate the safe introduction of hydrogen as an energy carrier, by removing the described safety related obstacles. The network is constituted by 24 partners from 12 European countries and from Canada, representing private industries, especially from the automotive sector, universities and research institutions. More than 120 scientists perform integrative work in 15 work packages. A biennial report on Hydrogen Safety is going to be published, the available experimental facilities have been catalogued and qualified, educational programs are designed. After the first successful International Conference on Hydrogen Safety the second will be organized 2007 in San Sebastian, Spain. The European codes and standards activities will be supported by scientifically based information formulated in the HySafe position papers. The web-site www.hysafe.net offers a versatile platform for internal and external communication. The further work program is orientated not only at the results of a state-of-the-art report and a PIRT analysis performed within the NoE but also complies with the needs identified in the external network including other European projects related to hydrogen like StorHy, HyWays and NATURALHY. By shifting

Effects of the International Temperature Scale of 1990 (ITS-90) on CIE documentary standards for radiometry, photometry, and colorimetry

International Nuclear Information System (INIS)

Mielenz, K.D.; Hsia, J.J.

1990-01-01

The differences between ITS-90 and IPTS-68 (International Practical Temperature Scale of 1968) above 1235 K are described. It is shown that none of the following CIE (Commission Internationale de l'Eclairage or International Commission on Illumination) definitions or recommendations require revision because of the introduction of the ITS-90: International Lighting Vocabulary definitions; CIE Standard Illuminants A, D(65), other illuminants; and sources for realizing CIE Illuminants. The effect of the ITS-90 on previously calibrated sources for realizing CIE illuminants is negligibly small

Multi-boiling Heat Transfer Analysis of a Convective Straight Fin with Temperature-Dependent Thermal Properties and Internal Heat Generation

Directory of Open Access Journals (Sweden)

Gbeminiyi Sobamowo

2017-10-01

Full Text Available In this study, by using the finite volume method, the heat transfer in a convective straight fin with temperature-dependent thermal properties and an internal heat generation under multi-boiling heat transfer modes are analyzed. In this regard, the local heat transfer coefficient is considered to vary within a power-law function of temperature. In the present study, the coexistence of all the boiling modes is taken into consideration. The developed heat transfer models and the corresponding numerical solutions are used to investigate the effects of various thermo-geometric parameters on the thermal performance of the longitudinal rectangular fin. The results shows that the fin temperature distribution, the total heat transfer, and the fin efficiency are significantly affected by the thermo-geometric parameters of the fin and the internal heat generation within the fin. The obtained results can provide a platform for improvements in the design of the fin in the heat transfer equipment.

Safe Anesthesia For Every Tot

DEFF Research Database (Denmark)

Weiss, Markus; Vutskits, Laszlo; Hansen, Tom G

2015-01-01

PURPOSE OF REVIEW: The term 'safe use of anesthesia in children is ill-defined and requires definition of and focus on the 'safe conduct of pediatric anesthesia'. RECENT FINDINGS: The Safe Anesthesia For Every Tot initiative (www.safetots.org) has been set up during the last year to focus...... on the safe conduct of pediatric anesthesia. This initiative aims to provide guidance on markers of quality anesthesia care. The introduction and implementation of national regulations of 'who, where, when and how' are required and will result in an improved perioperative outcome in vulnerable children....... The improvement of teaching, training, education and supervision of the safe conduct of pediatric anesthesia are the main goals of the safetots.org initiative. SUMMARY: This initiative addresses the well known perioperative risks in young children, perioperative causes for cerebral morbidity as well as gaps...

Outlooks for the development of ozone-safe refrigerant production at the Minatom facilities

International Nuclear Information System (INIS)

Shatalov, V.V.; Orekhov, V.T.; Dedov, A.S.; Zakharov, V.Yu.; Golubev, A.N.; Tsarev, V.A.

2001-01-01

Results of activities undertaken at the All-Russian Research Institute of Chemical Technology since 1988, which were aimed at search of new methods of synthesis of ozone-safe refrigerants, using depleted uranium hexafluoride waste formed at gas-diffusion plants as fluorinating agent, are considered. It is pointed out that major advantages of the flowsheets making use of UF 6 versus traditional method consist in the fact that the processes are conducted in gas phase under normal pressure and moderate temperatures with UF 6 transfer into a more environmentally friendly form. Outlooks for expansion of production of ozone-safe refrigerants by the method described are discussed [ru

Safe Handling of Radioisotopes. Health Physics Addendum

Energy Technology Data Exchange (ETDEWEB)

Appleton, G J; Krishnamoorthy, P N

1960-07-15

The International Atomic Energy Agency published in 1958 a Manual entitled ''Safe Handling of Radioisotopes'' (Safety Series No. 1 - STI/PUB/1), based on the work of an international panel convened by the Agency. As recommended by that panel and approved by the Agency's Board of Governors, this Addendum has now been prepared, primarily as a supplement to the Manual. It contains technical information necessary for the implementation of the controls given in the Manual. In addition, it is intended to serve as a brief introduction to the technical problems encountered in radiological protection work and to the methods of resolving them. As in the case of the Manual itself, the information given in this Addendum is particularly relevant to the problems encountered by the small user of radioisotopes. Although the basic principles set forth in it apply to all work with radiation sources, the Addendum is not intended to serve as a radiological protection manual for use in reactor installations or large-scale nuclear industry, where more specialized techniques and information are required.

Safe Handling of Radioisotopes. Health Physics Addendum

International Nuclear Information System (INIS)

Appleton, G.J.; Krishnamoorthy, P.N.

1960-01-01

The International Atomic Energy Agency published in 1958 a Manual entitled ''Safe Handling of Radioisotopes'' (Safety Series No. 1 - STI/PUB/1), based on the work of an international panel convened by the Agency. As recommended by that panel and approved by the Agency's Board of Governors, this Addendum has now been prepared, primarily as a supplement to the Manual. It contains technical information necessary for the implementation of the controls given in the Manual. In addition, it is intended to serve as a brief introduction to the technical problems encountered in radiological protection work and to the methods of resolving them. As in the case of the Manual itself, the information given in this Addendum is particularly relevant to the problems encountered by the small user of radioisotopes. Although the basic principles set forth in it apply to all work with radiation sources, the Addendum is not intended to serve as a radiological protection manual for use in reactor installations or large-scale nuclear industry, where more specialized techniques and information are required.

Measurement of Internal Friction for Tungsten by the Curve Vibrating Method with Variation of Voltage and Temperature

Directory of Open Access Journals (Sweden)

Elin Yusibani

2013-12-01

Full Text Available Application of a curved vibrating wire method (CVM to measure gas viscosity has been widely used. A fine Tungsten wire with 50 mm of diameter is bent into a semi-circular shape and arranged symmetrically in a magnetic field of about 0.2 T. The frequency domain is used for calculating the viscosity as a response for forced oscillation of the wire. Internal friction is one of the parameter in the CVM which is has to be measured beforeahead. Internal friction coefficien for the wire material which is the inverse of the quality factor has to be measured in a vacuum condition. The term involving internal friction actually represents the effective resistance of motion due to all non-viscous damping phenomena including internal friction and magnetic damping. The testing of internal friction measurement shows that at different induced voltage and elevated temperature at a vacuum condition, it gives the value of internal friction for Tungsten is around 1 to 4 10-4.

Internal development of vegetative buds of Norway spruce trees in relation to accumulated chilling and forcing temperatures.

Science.gov (United States)

Viherä-Aarnio, Anneli; Sutinen, Sirkka; Partanen, Jouni; Häkkinen, Risto

2014-05-01

The timing of budburst of temperate trees is known to be controlled by complicated interactions of temperature and photoperiod. To improve the phenological models of budburst, better knowledge of the internal bud development preceding budburst in relation to environmental cues is needed. We studied the effect of accumulated chilling and forcing temperatures on the internal development of vegetative buds preceding budburst in Norway spruce [Picea abies (L.) Karst.]. Branches from 17-year-old trees of southern Finnish origin were transferred eight times at 1- to 2-week intervals from October to December 2007 from the field at Punkaharju (61°48'N, 29°20'E) to the greenhouse with forcing conditions (day length 12 h, +20 °C). After seven different durations of forcing, the developmental phase and primordial shoot growth of the buds were analysed at the stereomicroscopic level. Air temperature was recorded hourly throughout the study period. The accumulated chilling unit sum had a significant effect on the temperature sum that was required to attain a certain developmental phase; a higher amount of chilling required a lower amount of forcing. The variation in the rate of development of different buds within each sample branch in relation to the chilling unit and forcing temperature sum was low. Regarding primordial shoot growth, there was also an inverse relation between accumulated chilling and forcing, i.e., a higher accumulated chilling unit sum before forcing required a lower temperature sum to initiate primordial shoot growth and resulted in a stronger effect of accumulated forcing. A second-order regression model with an interaction of chilling and forcing explained the variation of primordial shoot growth with high precision (R(2) = 0.88). However, further studies are required to determine the final parameter values to be used in phenological modelling. © The Author 2014. Published by Oxford University Press. All rights reserved.

The internal energy and thermodynamic behaviour of a boson gas below the Bose-Einstein temperature

International Nuclear Information System (INIS)

Deeney, F.A.; O'Leary, J.P.

2011-01-01

We have examined the issue of the kinetic energy of particles in the ground state of an ideal boson gas. By assuming that the particles, on dropping into the ground state, retain the kinetic energy they possess at the Bose-Einstein temperature T B , we obtain new expressions for the pressure and internal energy of the gas below T B , that are free of the difficulties associated with the corresponding expressions in current theory. Furthermore, these new equations yield a value for the maximum density temperature in liquid 4 He that is very close to the measured value. - Highlights: → A new equation of state for an ideal boson gas that is anomaly-free. → A prediction of the existence of a density maximum in all ideal boson gases. → Calculation of the temperature at which a density maximum will occur in liquid 4 He.

The safe home project.

Science.gov (United States)

Arphorn, Sara; Jiraniratisai, Sopaphan; Rungtakul, Rungsri; Phutta, Nikom

2011-12-01

The Thai Health Promotion Foundation supported the Improvement of Quality of Life of Informal Workers project in Ban Luang District, Amphur Photaram, Ratchaburi Province. There were many informal workers in Ban Luang District. Sweet-crispy fish producers in Ban Luang were the largest group among the sweet-crispy fish producers in Thailand. This project was aimed at improving living and working conditions of informal workers, with a focus on the sweet-crispy fish group. Good practices of improved living and working conditions were used to help informal workers build safe, healthy and productive work environments. These informal workers often worked in substandard conditions and were exposed to various hazards in the working area. These hazards included risk of exposure to hot work environment, ergonomics-related injuries, chemical hazards, electrical hazards etc. Ergonomics problems were commonly in the sweet-crispy fish group. Unnatural postures such as prolonged sitting were performed dominantly. One hundred and fifty informal workers participated in this project. Occupational health volunteers were selected to encourage occupational health and safety in four groups of informal workers in 2009. The occupational health volunteers trained in 2008 were farmers, beauty salon workers and doll makers. The occupational health and safety knowledge is extended to a new informal worker group: sweet-crispy fish producer, in 2009. The occupational health and safety training for sweet-crispy fish group is conducted by occupational health volunteers. The occupational health volunteers increased their skills and knowledge assist in to make safe home and safe community through participatory oriented training. The improvement of living and working condition is conducted by using a modified WISH, Work Improvement for Safe Home, checklist. The plans of improvement were recorded. The informal workers showed improvement mostly on material handling and storage. The safe uses and safe

Blood, donors and dollars: Rethinking financial sustainability of safe blood services in Tanzania

Directory of Open Access Journals (Sweden)

Kahabi Ganka Isangula

2016-01-01

Full Text Available Introduction Collection, processing and distribution of safe blood in Tanzania occurs within a free-for-service context, that is, a collection from non-remunerated blood donors and distributing freely to the needy people through health facilities. The safe blood services in the country appear to be crippled with many challenges and cannot meet the demand for blood and its products. As such, a need for rethinking collection methods, financial models and possible mechanisms for donor remuneration is evident. Methods In this paper, we venture on multi-stakeholder meetings and ongoing discussions regarding the internal mechanisms of safe blood transfusion financing. The intent is to offer a perspective on the considerations for self- sustaining safe blood services in the country and the extent to which they may be implemented or not. Results We suggest that despite huge demand, the external donor dependent financing mechanisms for safe blood services in the country are ineffective. Therefore, we discuss two potential ‘internal’ financing mechanisms that have been identified in recent shareholders forums 1 introducing a blood processing fee accompanied by policy change to allow direct charging of either recipients or hospitals or 2 influencing the introduction of ‘blood services’ within the current insurance schemes. Conclusion We conclude that there is a need for constructing alternative financial mechanisms to sustain the demand of safe blood in the country. We discuss two cost recovery mechanisms, blood processing fee and insurance schemes; however, warning is noted that their implementation warrants structural adjustments, massive community sensitization and optimum stakeholder engagement to maximize acceptability within the country.

Fail-safe system for activity cooled supersonic and hypersonic aircraft. [using liquid hydrogen fuel

Science.gov (United States)

Jones, R. A.; Braswell, D. O.; Richie, C. B.

1975-01-01

A fail-safe-system concept was studied as an alternative to a redundant active cooling system for supersonic and hypersonic aircraft which use the heat sink of liquid-hydrogen fuel for cooling the aircraft structure. This concept consists of an abort maneuver by the aircraft and a passive thermal protection system (TPS) for the aircraft skin. The abort manuever provides a low-heat-load descent from normal cruise speed to a lower speed at which cooling is unnecessary, and the passive TPS allows the aircraft skin to absorb the abort heat load without exceeding critical skin temperature. On the basis of results obtained, it appears that this fail-safe-system concept warrants further consideration, inasmuch as a fail-safe system could possibly replace a redundant active cooling system with no increase in weight and would offer other potential advantages.

Acceptance and Use of Eight Arsenic-Safe Drinking Water Options in Bangladesh

Science.gov (United States)

Inauen, Jennifer; Hossain, Mohammad Mojahidul; Johnston, Richard B.; Mosler, Hans-Joachim

2013-01-01

Arsenic contamination of drinking water is a serious public health threat. In Bangladesh, eight major safe water options provide an alternative to contaminated shallow tubewells: piped water supply, deep tubewells, pond sand filters, community arsenic-removal, household arsenic removal, dug wells, well-sharing, and rainwater harvesting. However, it is uncertain how well these options are accepted and used by the at-risk population. Based on the RANAS model (risk, attitudes, norms, ability, and self-regulation) this study aimed to identify the acceptance and use of available safe water options. Cross-sectional face-to-face interviews were used to survey 1,268 households in Bangladesh in November 2009 (n = 872), and December 2010 (n = 396). The questionnaire assessed water consumption, acceptance factors from the RANAS model, and socioeconomic factors. Although all respondents had access to at least one arsenic-safe drinking water option, only 62.1% of participants were currently using these alternatives. The most regularly used options were household arsenic removal filters (92.9%) and piped water supply (85.6%). However, the former result may be positively biased due to high refusal rates of household filter owners. The least used option was household rainwater harvesting (36.6%). Those who reported not using an arsenic-safe source differed in terms of numerous acceptance factors from those who reported using arsenic-safe sources: non-users were characterized by greater vulnerability; showed less preference for the taste and temperature of alternative sources; found collecting safe water quite time-consuming; had lower levels of social norms, self-efficacy, and coping planning; and demonstrated lower levels of commitment to collecting safe water. Acceptance was particularly high for piped water supplies and deep tubewells, whereas dug wells and well-sharing were the least accepted sources. Intervention strategies were derived from the results in order to

Infant Safe Sleep Interventions, 1990-2015: A Review.

Science.gov (United States)

Salm Ward, Trina C; Balfour, Giselle M

2016-02-01

Sleep-related infant deaths remain a major public health issue. Multiple interventions have been implemented in efforts to increase adherence to safe sleep recommendations. We conducted a systematic review of the international research literature to synthesize research on interventions to reduce the risk of sleep-related deaths and their effectiveness in changing infant sleep practices. We searched PubMed, CINAHL, PsycINFO, and Google Scholar for peer-reviewed articles published between 1990 and 2015 which described an intervention and reported results. Twenty-nine articles were included for review. Studies focused on infant caregivers, health care professionals, peers, and child care professionals. Targeted behaviors included sleep position, location, removing items from the crib, breastfeeding, smoke exposure, clothing, pacifier use, and knowledge of Sudden Infant Death Syndrome. Most articles described multi-faceted interventions, including: one-on-one or group education, printed materials, visual displays, videos, and providing resources such as cribs, pacifiers, wearable blankets, and infant t-shirts. Two described public education campaigns, one used an educative questionnaire, and one encouraged maternal note taking. Health professional interventions included implementing safe sleep policies, in-service training, printed provider materials, eliciting agreement on a Declaration of Safe Sleep Practice, and sharing adherence data. Data collection methods included self-report via surveys and observational crib audits. Over half of the studies utilized comparison groups which helped determine effectiveness. Most articles reported some degree of success in changing some of the targeted behaviors; no studies reported complete adherence to recommendations. Future studies should incorporate rigorous evaluation plans, utilize comparison groups, and collect demographic and collect follow-up data.

International regulatory activities

International Nuclear Information System (INIS)

Anon.

2002-01-01

Different international regulatory activities are presented: recommendation on the protection of the public against exposure to radon in drinking water supplies, amendment to the legislation implementing the regulation on imports of agricultural products originating in third countries following the Chernobyl accident, resolution on the commission green paper towards a European strategy for the security of energy supply, declaration of mandatory nature of the international code for the safe carriage of packaged irradiated nuclear fuel, plutonium and high level radioactive wastes on board ships, adoption of action plan against nuclear terrorism. (N.C.)

Designing for elevated temperature

International Nuclear Information System (INIS)

Boer, G.A. de

1982-01-01

The reasons for the application of higher process temperatures are explained. The properties of stainless steel are compared with those of other materials such as molybdenum. Factors influencing the choice of the material such as availability of material data at high temperature, controllability, and strength of heat-affected zone are discussed. The process of designing a structure for safe and economic high-temperature application is outlined: design-by-analysis in contrast to the design-by-rule which is general practice for low-temperature applications. The rules laid down in the ASME Pressure Vessel Code Case N47 are explained as well as the procedure for inelastic stress calculations. (author)

Method for making a low density polyethylene waste form for safe disposal of low level radioactive material

Science.gov (United States)

Colombo, P.; Kalb, P.D.

1984-06-05

In the method of the invention low density polyethylene pellets are mixed in a predetermined ratio with radioactive particulate material, then the mixture is fed through a screw-type extruder that melts the low density polyethylene under a predetermined pressure and temperature to form a homogeneous matrix that is extruded and separated into solid monolithic waste forms. The solid waste forms are adapted to be safely handled, stored for a short time, and safely disposed of in approved depositories.

SAFE/SNAP application to shipboard security

International Nuclear Information System (INIS)

Grady, L.M.; Walker, J.L.; Polito, J.

1981-11-01

An application of the combined Safeguards Automated Facility Evaluation/Safeguards Network Analysis Procedure (SAFE/SNAP) modeling technique to a physical protection system (PPS) aboard a generic ship is described. This application was performed as an example of how the SAFE and SNAP techniques could be used. Estimates of probability of interruption and neutralization for the example shipboard PPS are provided by SAFE as well as an adversary scenario, which serves as input to SNAP. This adversary scenario is analyzed by SNAP through four cases which incorporate increasingly detailed security force tactics. Comparisons between the results of the SAFE and SNAP analyses are made and conclusions drawn on the validity of each technique. Feedback from SNAP to SAFE is described, and recommendations for upgrading the ship based on the results of the SAFE/SNAP application are also discussed

Procurement Officer | IDRC - International Development Research ...

International Development Research Centre (IDRC) Digital Library (Canada)

... which involves exercising sound judgement, flexibility and the application of previous ... Plans and organizes the logistics required to safely and efficiently ship client's ... risks, and costs associated with domestic and international shipments;.

Target Trailing With Safe Navigation With Colregs for Maritime Autonomous Surface Vehicles

Science.gov (United States)

Kuwata, Yoshiaki (Inventor); Wolf, Michael T. (Inventor); Zarzhitsky, Dimitri V. (Inventor); Aghazarian, Hrand (Inventor); Huntsberger, Terrance L. (Inventor); Howard, Andrew B. (Inventor)

2014-01-01

Systems and methods for operating autonomous waterborne vessels in a safe manner. The systems include hardware for identifying the locations and motions of other vessels, as well as the locations of stationary objects that represent navigation hazards. By applying a computational method that uses a maritime navigation algorithm for avoiding hazards and obeying COLREGS using Velocity Obstacles to the data obtained, the autonomous vessel computes a safe and effective path to be followed in order to accomplish a desired navigational end result, while operating in a manner so as to avoid hazards and to maintain compliance with standard navigational procedures defined by international agreement. The systems and methods have been successfully demonstrated on water with radar and stereo cameras as the perception sensors, and integrated with a higher level planner for trailing a maneuvering target.

Characterization of Decommissioned PWR Vessel Internals Materials Samples: Material Certification, Fluence, and Temperature (Nonproprietary Version)

International Nuclear Information System (INIS)

Krug, M.; Shogan, R.; Fero, A.; Snyder, M.

2004-01-01

Pressurized water reactor (PWR) cores, operate under extreme environmental conditions due to coolant chemistry, operating temperature, and neutron exposure. Extending the life of PWRs require detailed knowledge of the changes in mechanical and corrosion properties of the structural austenitic stainless steel components adjacent to the fuel. This report contains basic material characterization information of the as-installed samples of reactor internals material which were harvested from a decommissioned PWR

Safe Handling of Radioisotopes. First Edition with Revised Appendix I

International Nuclear Information System (INIS)

1966-01-01

Under its Statute the International Atomic Energy Agency is empowered to provide for the application of standards of safety for protection against radiation to its own operations and to operations making use of assistance provided by it or with which it is otherwise directly associated. To this end authorities receiving such assistance are required to observe relevant health and safety measures prescribed by the Agency. As a first step, it was considered an urgent task to provide users of radioisotopes with a manual of practice for the safe handling of these substances. The first edition of such a manual was published in 1958 and represented the first of the 'Safety Series', a series of manuals and codes on health and safety published by the Agency. It was prepared after careful consideration of existing national and international codes of radiation safety by a group of international experts and in consultation with other international bodies. This edition presents the first revision. It incorporates in the Appendices the latest recommendations of the International Commission on Radiological Protection and extracts from the report of the Committee II of the I.C.R.P. on permissible dose for internal radiation. The Health Physics and Medical Addenda to this Manual, published as No. 2 and No. 3 in the Safety Series in 1960, give more complete advice to the user on specialized topics.

Protein Internal Dynamics Associated With Pre-System Glass Transition Temperature Endothermic Events: Investigation of Insulin and Human Growth Hormone by Solid State Hydrogen/Deuterium Exchange.

Science.gov (United States)

Fang, Rui; Grobelny, Pawel J; Bogner, Robin H; Pikal, Michael J

2016-11-01

Lyophilized proteins are generally stored below their glass transition temperature (T g ) to maintain long-term stability. Some proteins in the (pure) solid state showed a distinct endotherm at a temperature well below the glass transition, designated as a pre-T g endotherm. The pre-T g endothermic event has been linked with a transition in protein internal mobility. The aim of this study was to investigate the internal dynamics of 2 proteins, insulin and human growth hormone (hGH), both of which exhibit the pre-T g endothermic event with onsets at 50°C-60°C. Solid state hydrogen/deuterium (H/D) exchange of both proteins was characterized by Fourier transform infrared spectroscopy over a temperature range from 30°C to 80°C. A distinct sigmoidal transition in the extent of H/D exchange had a midpoint of 56.1 ± 1.2°C for insulin and 61.7 ± 0.9°C for hGH, suggesting a transition to greater mobility in the protein molecules at these temperatures. The data support the hypothesis that the pre-T g event is related to a transition in internal protein mobility associated with the protein dynamical temperature. Exceeding the protein dynamical temperature is expected to activate protein internal motion and therefore may have stability consequences. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

A Micropulse eye-safe all-fiber molecular backscatter coherent temperature lidar

Directory of Open Access Journals (Sweden)

Abari Cyrus F.

2016-01-01

Full Text Available In this paper, we analyze the performance of an all-fiber, micropulse, 1.5 μm coherent lidar for remote sensing of atmospheric temperature. The proposed system benefits from the recent advances in optics/electronics technology, especially an all-fiber image-reject homodyne receiver, where a high resolution spectrum in the baseband can be acquired. Due to the presence of a structured spectra resulting from the spontaneous Rayleigh-Brillouine scattering, associated with the relevant operating regimes, an accurate estimation of the temperature can be carried out. One of the main advantages of this system is the removal of the contaminating Mie backscatter signal by electronic filters at the baseband (before signal conditioning and amplification. The paper presents the basic concepts as well as a Monte-Carlo system simulation as the proof of concept.

Light water ultra-safe plant concept: First annual report

International Nuclear Information System (INIS)

Klevans, E.

1987-01-01

Since the accident at Three Mile Island (TMI) Penn State Nuclear Engineering Department Faculty and Staff have considered various methods to improve already safe reactor designs and public perception of the safety of Nuclear Power. During the last year, the Department of Energy funded the study of a plant reconfiguration originally proposed by M.A. Shultz. This report presents the status of the project at the end of the first year. A broad set of specifications to improve safety and public perception were set forth and the realization of these goals is achieved in a plant design named, ''The Light Water Ultra-Safe Plant Concept.'' The most significant goals of the concept address the station black-out problem and simplification of required operator actions during abnormal situations. These goals are achieved in the Ultra-Safe Concept by addition of an in-containment atmospheric tank containing a large quantity of cool water, replacement of the conventional PWR pressurizer system with a pressurizing pump, internal emergency power generation, and arrangement of components to utilize natural circulation at shut-down. The first year effort included an evaluation of the normal operation characteristics of the primary system pressurizing concept, evaluating parameters and modeling for analysis of the shutdown scenario, design of a low power density core, design of a low-pressure waste handling system, arrangement of a drainage system for pipe break considerations, and failure modes and effects analysis

Electronic Data Safes as an Infrastructure for Transformational Government? A Case Study

OpenAIRE

Pfister, Joachim; Schwabe, Gerhard

2015-01-01

Part 3: Services, Processes and Infrastructure; International audience; This article introduces and explores the potential of an active electronic data safe (AEDS) serving as an infrastructure to achieve transformational government. An AEDS connects individuals and organizations from the private and the public sector to exchange information items related to business processes following the user-managed access paradigm. To realize the transformational government’s vision of user-centricity, fu...

Chernobyl new safe confinement

International Nuclear Information System (INIS)

Dodd, L.

2011-01-01

The author presents the new safe confinement that will be commissioned at Unit 4 of the Chernobyl NPP in 2015. The confinement will ensure that Chernobyl Unit 4 will be placed in an environmentally safe condition for at least next 100 years. The article highlights the current work status, future perspectives and the feasibility of confinement concept [ru

Asymptotically Safe Dark Matter

DEFF Research Database (Denmark)

Sannino, Francesco; Shoemaker, Ian M.

2015-01-01

We introduce a new paradigm for dark matter (DM) interactions in which the interaction strength is asymptotically safe. In models of this type, the coupling strength is small at low energies but increases at higher energies, and asymptotically approaches a finite constant value. The resulting...... searches are the primary ways to constrain or discover asymptotically safe dark matter....

THE ROLE OF TEENAGEERS’ LIFE EXPERIENCE ACTUALIZATION IN THE FRAMEWORK OF THE SAFE SOCIAL ENVIRONMENT FORMATION

Directory of Open Access Journals (Sweden)

O. A. Selivanov

2013-01-01

Full Text Available The paper looks at the problem of social security and emphasizes the urgent need for developing the general theory of social security, its concepts and models designed to meet the requirements of time and specify different aspects and levels of socialization process – federal, regional and municipal. The author regards actualization of teenagers’ life experience as a promising direction for exploring the opportunities for creating the safe social environment.The individual socio-psychological functioning is delineated as a multilevel correlation of internal and external human resources used for resolving difficult situations. According to the author, the prompt mobilization of internal resources of a teenager, training the ability to apply the external resources for solving the problem and developing the safe behavior can improve the quality of life in the modern society. Along with the risks of modern information society, the author emphasizes a number of dangerous social trends: disruption of social institutions, ifantilization of education, distortion of historical cultural channels, and devaluation of the collectivism idea.In author’s opinion, teenagers should get some special knowledge and individual training to develop the skills of safe behavior in actual situations; and the prospects of the modern society considerably depend on the above procedures. 

Royal Decree 1749/1984 of 1 August approving the national regulations on the safe transport of dangerous goods by air together with technical instructions for the safe transport of dangerous goods by air

International Nuclear Information System (INIS)

1984-01-01

This Royal Decree approves the national Regulations on the safe transport of dangerous goods by air. The Regulations as well as the attached detailed technical instructions are based on the 1981 revised text of the Annex concerning dangerous goods of the Chicago Convention on International Civil Aviation. It also covers radioactive materials. (NEA) [fr

Effect of dietary organic selenium and zinc on the internal egg quality of quail eggs for different periods and under different temperatures

Directory of Open Access Journals (Sweden)

IB Fernandez

2011-03-01

Full Text Available The objective of this study was to evaluate the internal quality of eggs of Japanese quails fed diets supplemented with chelated selenium and zinc. The experiment was carried out for 120 days, and 144 birds were divided in random blocks into four treatments (control; 0.3 ppm Se; 60 ppm Zn and 0.3 ppm Se + 60 ppm Zn. Ten, 14, 18, and 22 weeks after the beginning of lay, eggs were collected and stored under two different temperatures (environmental temperature or refrigeration and for 10, 20, and 30 days. Eggs were analyzed for: Haugh units (HU, albumen height (AH, yolk index (YI, and albumen index (AI. Parameters were only statistically influenced by the interaction between dietary treatment and storage time. It was concluded that the addition of organic Se and Zn influenced internal egg quality when eggs were stored up to 20 days, independently of storage temperature, suggesting that the combined supplementation of organic Se and Zn improve internal egg quality and extend egg shelf life.

A safe strategy for addition of vitamins and minerals to foods

DEFF Research Database (Denmark)

Rasmussen, S.; Andersen, Niels Lyhne; Dragsted, L.O.

2006-01-01

Addition of vitamins and minerals to foods must be done without health risk to any consumer group. International expert groups have aimed at establishing tolerable upper intake levels (ULs) for vitamins and minerals although lack of solid data on their safety is a major obstacle to this work....... The levels are applied in a model for calculation of safe fortification levels for all ages.We have estimated the upper 95(th) percentile intake of vitamins and minerals from food in various Danish age and gender groups and suggest that a daily multivitaminmineral pill is included in the calculation of total...... dietary intake levels of all vitamins and minerals. By subtracting this dietary intake level from the UL, GL or TGL, we calculate the amount that can be safely used for fortification. Since safety must be assured for all age groups, the smallest difference relative to energy intake calculated for any age...

Low temperature internal friction on γ-irradiated polyvinylidene fluoride (PVDF)

International Nuclear Information System (INIS)

Callens, A.; Eersels, L.; De Batist, R.

1978-01-01

A least-squares fitting of the below room temperature part of the internal friction spectra, obtained by the torsion pendulum technique on as-received and γ-irradiated (up to 1 Grad) strips and fibres of polyvinylidene fluoride by a superposition of single Debye functions, reveals that the spectral component features are determined not only by purely amorphous chain characteristics but also by the dose-dependence of crystallinity. A careful analysis of the relaxation spectra confirms that at least one relaxation effect (approximately 236 K) is created upon irradiation. The analysis of the dose dependence of the characteristics of the β (glass transition; approximately 220 K) and βsub(u) (apparent upper glass transition; approximately 270 K) relaxations, suggests the probable influence of crystallinity on the molecular motion in the amorphous phase. The increase of the intensity of the γ relaxation (approximately 190 K) is related to the irradiation-induced crystallite degradation. (author)

International co-operation. Key issue paper no. 6

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

In accordance with guidance provided by the Steering Group, this report assesses the adequacy and effectiveness of international co-operation relating to the nuclear fuel cycle, with a view toward identifying any needed new forms or arrangements for co-operation. In more specific terms, the Steering Committee`s guidance identified the following questions: Is the existing international framework sufficient for: the safe and secure operation of the fuel cycle; the economic and orderly development of the world`s nuclear energy systems (or their phase-out should this take place); international co-operation in R and D; international co-operation in industrial activities? Are there places where these requirements overlap or interact so as to impede activities which are desirable? Can new forms of co-operation be foreseen which would make it easier to implement any of the fuel cycle options in a safe, secure and responsible way? Are there other new forms of international co-operation which would affect the fuel cycle, e.g. regional institutions; international plutonium management regime and/or storage? Finally: What is the appropriate role of IAEA in any of these?.

High energy eye-safe and mid-infrared optical parametric oscillator

International Nuclear Information System (INIS)

Liu, J; Liu, Q; Huang, L; Gong, M

2010-01-01

A high energy eye-safe and mid-infrared optical parametric oscillator (OPO) is demonstrated. The nonlinear media is a Y-cut KTA crystal with the length of 20 mm, which is pumped by a Nd:YAG laser. Both eye-safe and mid-infrared laser are output with high energy. When the pump energy is 1 J and the pulse duration is 10 ns, we get 53 mJ idler at 3.632 μm and 151 mJ signal at 1.505 μm. As we know, the idler energy is the highest at the wavelength beyond 3.5 μm and the signal energy is the highest with Y-cut KTA. The results prove that the Y-cut KTA crystal can produce the signal and idler with the energies as high as these in the paper. We have tested the temperature-tuning characters and the coefficient of the idler is 0.26 nm/°C

Mexico into the globalization: Nuevo Leon, the safe border for international trade program

Directory of Open Access Journals (Sweden)

Barragan, J.

2006-07-01

Full Text Available The presentation of this research paper in the 10th annual Conference of the Western Hemispheric Development in the University of Texas A&M in Laredo Texas, (April 23-25, 2005 brought a great opportunity to reflect the efforts of a region in the north of Mexico for the world’s peace and security inside the International trade with the gowth factors important for any and all nations. In this investigation the combined efforts of USA and Mexico are shown to protect the International Trade against the acts of terrorism and smuggling of illegal drugs which constantly try to infiltrate their illicit activities, delivering a great damage to companies that carry out activities of international trade. Relevant conclusions are presented at the end of the paper.

Residential tornado safe room from commodity wood products – impact and wind pressure testing

Science.gov (United States)

Robert H. Falk; James J. Bridwell; C. Adam Senalik; Marshall Begel

2018-01-01

A tornado safe room is a shelter designed to provide protection during a tornado and is specifically engineered to resist the high wind pressures and debris impact generated by these high wind events. The required performance criteria of these shelters has been established and is found in the International Code Council Standard for the Design and Construction of Storm...

75 FR 1734 - Children’s Online Privacy Protection Rule Safe Harbor Proposed Self-Regulatory Guidelines; i-SAFE...

Science.gov (United States)

2010-01-13

... Proposed Self-Regulatory Guidelines; i-SAFE, Inc. Application for Safe Harbor AGENCY: Federal Trade... for public comment concerning proposed self-regulatory guidelines submitted by i-SAFE, Inc. under the... approval self-regulatory guidelines that would implement the Rule's protections.\\3\\ \\1\\ 64 FR 59888 (1999...

Creep-Fatigue Damage Evaluation of a Model Reactor Vessel and Reactor Internals of Sodium Test Facility according to ASME-NH and RCC-MRx Codes

International Nuclear Information System (INIS)

Lim, Dong-Won; Lee, Hyeong-Yeon; Eoh, Jae-Hyuk; Son, Seok-Kwon; Kim, Jong-Bum; Jeong, Ji-Young

2016-01-01

The objective of the STELLA-2 is to support the specific design approval for PGSFR by synthetic reviews of key safety issues and code validations through the integral effect tests. Due to its high temperature operation in SFRs (and in a testing facility) up to 550 °C, thermally induced creep-fatigue damage is very likely in components including a reactor vessel, reactor internals (interior structures), heat exchangers, pipelines, etc. In this study, structural integrity of the components such as reactor vessel and internals in STELLA-2 has been evaluated against creep-fatigue failures at a concept-design step. As 2D analysis yields far conservative results, a realistic 3D simulation is performed by a commercial software. A design integrity guarding against a creep-fatigue damage failure operating at high temperature was evaluated for the reactor vessel with its internal structure of the STELLA-2. Both the high temperature design codes were used for the evaluation, and results were compared. All the results showed the vessel as a whole is safely designed at the given operating conditions, while the ASME-NH gives a conservative evaluation

Creep-Fatigue Damage Evaluation of a Model Reactor Vessel and Reactor Internals of Sodium Test Facility according to ASME-NH and RCC-MRx Codes

Energy Technology Data Exchange (ETDEWEB)

Lim, Dong-Won; Lee, Hyeong-Yeon; Eoh, Jae-Hyuk; Son, Seok-Kwon; Kim, Jong-Bum; Jeong, Ji-Young [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The objective of the STELLA-2 is to support the specific design approval for PGSFR by synthetic reviews of key safety issues and code validations through the integral effect tests. Due to its high temperature operation in SFRs (and in a testing facility) up to 550 °C, thermally induced creep-fatigue damage is very likely in components including a reactor vessel, reactor internals (interior structures), heat exchangers, pipelines, etc. In this study, structural integrity of the components such as reactor vessel and internals in STELLA-2 has been evaluated against creep-fatigue failures at a concept-design step. As 2D analysis yields far conservative results, a realistic 3D simulation is performed by a commercial software. A design integrity guarding against a creep-fatigue damage failure operating at high temperature was evaluated for the reactor vessel with its internal structure of the STELLA-2. Both the high temperature design codes were used for the evaluation, and results were compared. All the results showed the vessel as a whole is safely designed at the given operating conditions, while the ASME-NH gives a conservative evaluation.

Safeness of radiological machinery

International Nuclear Information System (INIS)

Yokoyama, Shun

1979-01-01

The human factors affecting the safeness of radiological machinery, which are often very big and complicated machines, are described from the stand point of handling. 20 to 50% of the troubles on equipments seem to be caused by men. This percentage will become even higher in highly developed equipments. Human factors have a great influence on the safeness of radiological equipments. As the human factors, there are sensory factors and knowledge factors as well as psychological factors, and the combination of these factors causes mishandling and danger. Medical services at present are divided in various areas, and consist of the teamwork of the people in various professions. Good human relationship, education and control are highly required to secure the safeness. (Kobatake, H.)

A Micropulse eye-safe all-fiber molecular backscatter coherent temperature lidar

DEFF Research Database (Denmark)

Abari, Cyrus F.; Chu, Xinzhao; Mann, Jakob

2016-01-01

resolution spectrum in the baseband can be acquired. Due to the presence of a structured spectra resulting from the spontaneous Rayleigh-Brillouine scattering, associated with the relevant operating regimes, an accurate estimation of the temperature can be carried out. One of the main advantages...

Conductive Cotton Textile from Safely Functionalized Carbon Nanotubes

Directory of Open Access Journals (Sweden)

Mohammad Jellur Rahman

2015-01-01

Full Text Available Electroconductive cotton textile has been prepared by a simple dipping-drying coating technique using safely functionalized multiwalled carbon nanotubes (f-MWCNTs. Owing to the surface functional groups, the f-MWCNTs become strongly attached with the cotton fibers forming network armors on their surfaces. As a result, the textile exhibits enhanced electrical properties with improved thermal conductivity and therefore is demonstrated as a flexible electrothermal heating element. The fabricated f-MWCNTs/cotton textile can be heated uniformly from room temperature to ca. 100°C within few minutes depending on the applied voltage. The textile shows good thermal stability and repeatability during a long-term heating test.

Application of high-temperature superconducting coil for internal ring devices

Energy Technology Data Exchange (ETDEWEB)

Ogawa, Yuichi [High Temperature Plasma Center, University of Tokyo, 5-1-5 Kashiwanoha, Kashiwa, Chiba 277-8568 (Japan)]. E-mail: ogawa@ppl.k.u-tokyo.ac.jp; Morikawa, Junji [High Temperature Plasma Center, University of Tokyo, 5-1-5 Kashiwanoha, Kashiwa, Chiba 277-8568 (Japan); Mito, Toshiyuki [National Institute for Fusion Science, Oroshi, Toki, Gifu 509-5292 (Japan); Yanagi, Nagato [National Institute for Fusion Science, Oroshi, Toki, Gifu 509-5292 (Japan); Iwakuma, Masataka [Kyushu University, 6-10-1 Hakozaki, Higashi-ku, Fukuoka 812-8581 (Japan)

2006-11-15

A high-temperature superconducting (HTS) coil is applied for plasma confinement devices, where plasma is confined with a magnetic field of a floating HTS coil. The internal coil device mini-RT with a BSCCO tape has been constructed, in which the coil major radius and magnetomotive force are 0.15 m and 50 kA, respectively. The coil is cooled to 20 K with a helium gas by using a demountable transfer tube and check valve system. The coil current is directly excited by the external power supply with demountable electrodes. To reduce the heat load, the electrodes were cooled with liquid nitrogen. The levitation experiment of the HTS coil has been carried out. The position of the HTS coil is measured by laser sensors, and is feedback-controlled with the levitation coil current. We have succeeded in levitating the HTS coil during 1 h with accuracy of less than 20 {mu}m. The magnetic field strength near the internal coil is around 0.1 T, and a radio-frequency wave of 2.45 GHz is applied for the plasma production. At the floating condition of the HTS coil, a high-density plasma with more than 10{sup 17} m{sup -3}, which is higher than the cut-off density of a 2.45 GHz microwave, has been produced. A new device RT-1 with a major radius of 0.25 m and a magnetomotive force of 250 kA is under construction, and a persistent current has been demonstrated. The feasibility on YBCO tape is briefly discussed.

IAEA Mission Says France Committed to Safe, Responsible Management of Radioactive Waste

International Nuclear Information System (INIS)

2018-01-01

An International Atomic Energy Agency (IAEA) team of experts said France demonstrated a comprehensive commitment to safety with a responsible approach to the management of radioactive waste and spent nuclear fuel. The team also made suggestions aimed at further enhancements and noted several good practices. The Integrated Review Service for Radioactive Waste and Spent Fuel Management, Decommissioning and Remediation (ARTEMIS) team concluded an 11-day mission to France on 24 January. The mission, requested by the Government of France, was hosted by the Directorate General of Energy and Climate (DGEC), with the participation of officials from several relevant organizations including the French National Radioactive Waste Agency (ANDRA) and the Nuclear Safety Authority (ASN), which is responsible for nuclear and radiation safety regulation in the country. ARTEMIS missions provide independent expert advice from an international team of specialists convened by the IAEA. Reviews are based on the IAEA safety standards as well as international good practices. The mission to France aimed to help the country meet European Union obligations that require an independent peer review of national programmes for the safe and responsible management of spent fuel and radioactive waste. Nuclear power currently generates more than 70 percent of France’s electricity. The country has 58 operating nuclear power reactors, which will require the continuing safe management of radioactive waste and spent fuel. France operates facilities for the disposal of very low-level and low-level wastes, and is developing a deep geological repository for the disposal of high-level waste.

The Role of Well Control Training in Developing Safe Onshore and Offshore Oil Drilling Operations

Science.gov (United States)

Abulhassn, Aber

2016-01-01

This research investigates the role of the International Well Control Forum (IWCF) Rotary Drilling Well Control Training Program in developing safe oil drilling operations from the perspective of onshore and offshore drilling crews. The research methodology is a qualitative case study. A total of 40 IWCF candidates were interviewed, with 10 from…

IDRC - International Development Research Centre |

International Development Research Centre (IDRC) Digital Library (Canada)

Learn moreArtificial intelligence and human development ... Our experts share insights on the issues and approaches challenging the international ... Shadow Libraries: Access to Knowledge in Global Higher Education · Book cover: ... Social Theories of Urban Violence in the Global South: Towards Safe and Inclusive Cities.

Isotopic dependence of the fragments' internal temperatures determined from multifragment emission

Science.gov (United States)

Souza, S. R.; Donangelo, R.

2018-05-01

The internal temperatures of fragments produced by an excited nuclear source are investigated by using the microcanonical version of the statistical multifragmentation model, with discrete energy. We focus on the fragments' properties at the breakup stage, before they have time to deexcite by particle emission. Since the adopted model provides the excitation energy distribution of these primordial fragments, it allows one to calculate the temperatures of different isotope families and to make inferences about the sensitivity to their isospin composition. It is found that, due to the functional form of the nuclear density of states and the excitation energy distribution of the fragments, proton-rich isotopes are hotter than neutron-rich isotopes. This property has been taken to be an indication of earlier emission of the former from a source that cools down as it expands and emits fragments. Although this scenario is incompatible with the prompt breakup of a thermally equilibrated source, our results reveal that the latter framework also provides the same qualitative features just mentioned. Therefore they suggest that this property cannot be taken as evidence for nonequilibrium emission. We also found that this sensitivity to the isotopic composition of the fragments depends on the isospin composition of the source, and that it is weakened as the excitation energy of the source increases.

Temperature metrology

Science.gov (United States)

Fischer, J.; Fellmuth, B.

2005-05-01

The majority of the processes used by the manufacturing industry depend upon the accurate measurement and control of temperature. Thermal metrology is also a key factor affecting the efficiency and environmental impact of many high-energy industrial processes, the development of innovative products and the health and safety of the general population. Applications range from the processing, storage and shipment of perishable foodstuffs and biological materials to the development of more efficient and less environmentally polluting combustion processes for steel-making. Accurate measurement and control of temperature is, for instance, also important in areas such as the characterization of new materials used in the automotive, aerospace and semiconductor industries. This paper reviews the current status of temperature metrology. It starts with the determination of thermodynamic temperatures required on principle because temperature is an intensive quantity. Methods to determine thermodynamic temperatures are reviewed in detail to introduce the underlying physical basis. As these methods cannot usually be applied for practical measurements the need for a practical temperature scale for day-to-day work is motivated. The International Temperature Scale of 1990 and the Provisional Low Temperature Scale PLTS-2000 are described as important parts of the International System of Units to support science and technology. Its main importance becomes obvious in connection with industrial development and international markets. Every country is strongly interested in unique measures, in order to guarantee quality, reproducibility and functionability of products. The eventual realization of an international system, however, is only possible within the well-functioning organization of metrological laboratories. In developed countries the government established scientific institutes have certain metrological duties, as, for instance, the maintenance and dissemination of national

Temperature metrology

International Nuclear Information System (INIS)

Fischer, J; Fellmuth, B

2005-01-01

The majority of the processes used by the manufacturing industry depend upon the accurate measurement and control of temperature. Thermal metrology is also a key factor affecting the efficiency and environmental impact of many high-energy industrial processes, the development of innovative products and the health and safety of the general population. Applications range from the processing, storage and shipment of perishable foodstuffs and biological materials to the development of more efficient and less environmentally polluting combustion processes for steel-making. Accurate measurement and control of temperature is, for instance, also important in areas such as the characterization of new materials used in the automotive, aerospace and semiconductor industries. This paper reviews the current status of temperature metrology. It starts with the determination of thermodynamic temperatures required on principle because temperature is an intensive quantity. Methods to determine thermodynamic temperatures are reviewed in detail to introduce the underlying physical basis. As these methods cannot usually be applied for practical measurements the need for a practical temperature scale for day-to-day work is motivated. The International Temperature Scale of 1990 and the Provisional Low Temperature Scale PLTS-2000 are described as important parts of the International System of Units to support science and technology. Its main importance becomes obvious in connection with industrial development and international markets. Every country is strongly interested in unique measures, in order to guarantee quality, reproducibility and functionability of products. The eventual realization of an international system, however, is only possible within the well-functioning organization of metrological laboratories. In developed countries the government established scientific institutes have certain metrological duties, as, for instance, the maintenance and dissemination of national

Quench evolution and hot spot temperature in the ATLAS B0 model coil

CERN Document Server

Dudarev, A; Boxman, H; Broggi, F; Dolgetta, N; Juster, F P; Tetteroo, M; ten Kate, H H J

2004-01-01

The 9-m long superconducting model coil B0 was built to verify design parameters and exercise the construction of the Barrel Toroid magnet of ATLAS Detector. The model coil has been successfully tested at CERN. An intensive test program to study quench propagation through the coil windings as well as the temperature distribution has been carried out. The coil is well equipped with pickup coils, voltage taps, superconducting quench detectors and temperature sensors. The current is applied up to 24 kA and about forty quenches have been induced by firing internal heaters. Characteristic numbers at full current of 24 kA are a normal zone propagation of 15 m/s in the conductor leading to a turn-to-turn propagation of 0.1 m/s, the entire coil in normal state within 5.5 s and a safe peak temperature in the windings of 85 K. The paper summarizes the quench performance of the B0 coil. Based on this experience the full-size coils are now under construction and first test results are awaited by early 2004. 7 Refs.

The ultimate safe (US) Reactor: A concept for the third millenium

International Nuclear Information System (INIS)

Gat, U.

1986-01-01

The Ultimate Safe (U.S.) Reactor is based on a novel safety concept. Fission products in the reactor are allowed to accumulate only to a level at which they would constitute a harmless source term. Removal of fission products also removes the decay heat - the driving force for the source term. The reactor has no excess criticality and is controlled by the reactivity temperature coefficient. Safety is inherent and passive. Waste is removed from the site promptly

Safe Cooperating Cyber-Physical Systems using Wireless Communication

DEFF Research Database (Denmark)

Pop, Paul; Scholle, Detlef; Sljivo, Irfan

2017-01-01

This paper presents an overview of the ECSEL project entitled ―Safe Cooperating Cyber-Physical Systems using Wireless Communication‖ (SafeCOP), which runs during the period 2016–2019. SafeCOP targets safety-related Cooperating Cyber-Physical Systems (CO-CPS) characterised by use of wireless...... detection of abnormal behaviour, triggering if needed a safe degraded mode. SafeCOP will also develop methods and tools, which will be used to produce safety assurance evidence needed to certify cooperative functions. SafeCOP will extend current wireless technologies to ensure safe and secure cooperation...

Materials for Nuclear Plants From Safe Design to Residual Life Assessments

CERN Document Server

Hoffelner, Wolfgang

2013-01-01

The clamor for non-carbon dioxide emitting energy production has directly  impacted on the development of nuclear energy. As new nuclear plants are built, plans and designs are continually being developed to manage the range of challenging requirement and problems that nuclear plants face especially when managing the greatly increased operating temperatures, irradiation doses and extended design life spans. Materials for Nuclear Plants: From Safe Design to Residual Life Assessments  provides a comprehensive treatment of the structural materials for nuclear power plants with emphasis on advanced design concepts.   Materials for Nuclear Plants: From Safe Design to Residual Life Assessments approaches structural materials with a systemic approach. Important components and materials currently in use as well as those which can be considered in future designs are detailed, whilst the damage mechanisms responsible for plant ageing are discussed and explained. Methodologies for materials characterization, material...

Technical and safe development features of modern research reactor

International Nuclear Information System (INIS)

Wang Jiaying; Dong Duo

1998-01-01

The development trend of research reactor in the world, and development situation in China are introduced. Up to now, some research reactors have serviced for long time and equipment have aged, not to be satisfied for requirement of science and technology development. New research reactors must been developed. The technical features and safe features of new type research reactor in China, for example: multi-pile utilization, compact core of high flux, high automation level of control, reactor two independent shutdown systems, great coefficient of negative temperature, passive safety systems, reliable residual heat removal system are studied

Towards Safe Navigation by Formalizing Navigation Rules

Directory of Open Access Journals (Sweden)

Arne Kreutzmann

2013-06-01

Full Text Available One crucial aspect of safe navigation is to obey all navigation regulations applicable, in particular the collision regulations issued by the International Maritime Organization (IMO Colregs. Therefore, decision support systems for navigation need to respect Colregs and this feature should be verifiably correct. We tackle compliancy of navigation regulations from a perspective of software verification. One common approach is to use formal logic, but it requires to bridge a wide gap between navigation concepts and simple logic. We introduce a novel domain specification language based on a spatio-temporal logic that allows us to overcome this gap. We are able to capture complex navigation concepts in an easily comprehensible representation that can direcly be utilized by various bridge systems and that allows for software verification.

Changing pattern of landslide risk in Europe - The SafeLand project

Science.gov (United States)

Nadim, F.; Kalsnes, B.

2012-04-01

The need to protect people and property with a changing pattern of landslide hazard and risk caused by climate change and changes in demography, and the reality for societies in Europe to live with the risk associated with natural hazards, were the motives for the project SafeLand: "Living with landslide risk in Europe: Assessment, effects of global change, and risk management strategies." SafeLand is a large, integrating research project under the European Commission's 7th Framework Programme (FP7). The project started on 1 May 2009 and will end on 30 April 2012. It involves 27 partners from 12 European countries, and has international collaborators and advisers from China, India, USA, Japan and Hong Kong. SafeLand also involves 25 End-Users from 11 countries. SafeLand is coordinated by the International Centre for Geohazards (ICG) at Norwegian Geotechnical Institute in Norway. Further information on the SafeLand project can be found at its web site http://safeland-fp7.eu/. Main results achieved in SafeLand include: - Various guidelines related to landslide triggering processes and run-out modelling. - Development and testing of several empirical methods for predicting the characteristics of threshold rainfall events for triggering of precipitation-induced landslides, and development of an empirical model for assessing the changes in landslide frequency (hazard) as a function of changes in the demography and population density. - Guideline for landslide susceptibility, hazard and risk assessment and zoning. - New methodologies for physical and societal vulnerability assessment. - Identification of landslide hazard and risk hotspots for Europe. The results show clearly where areas with the largest landslide risk are located in Europe and the objective approach allows a ranking of the countries by exposed area and population. - Different regional and local climate model simulations over selected regions of Europe at spatial resolutions of 10x10 km and 2.8x2.8 km

InaSAFE applications in disaster preparedness

Science.gov (United States)

Pranantyo, Ignatius Ryan; Fadmastuti, Mahardika; Chandra, Fredy

2015-04-01

Disaster preparedness activities aim to reduce the impact of disasters by being better prepared to respond when a disaster occurs. In order to better anticipate requirements during a disaster, contingency planning activities can be undertaken prior to a disaster based on a realistic disaster scenario. InaSAFE is a tool that can inform this process. InaSAFE is a free and open source software that estimates the impact to people and infrastructure from potential hazard scenarios. By using InaSAFE, disaster managers can develop scenarios of disaster impacts (people and infrastructures affected) to inform their contingency plan and emergency response operation plan. While InaSAFE provides the software framework exposure data and hazard data are needed as inputs to run this software. Then InaSAFE can be used to forecast the impact of the hazard scenario to the exposure data. InaSAFE outputs include estimates of the number of people, buildings and roads are affected, list of minimum needs (rice and clean water), and response checklist. InaSAFE is developed by Indonesia's National Disaster Management Agency (BNPB) and the Australian Government, through the Australia-Indonesia Facility for Disaster Reduction (AIFDR), in partnership with the World Bank - Global Facility for Disaster Reduction and Recovery (GFDRR). This software has been used in many parts of Indonesia, including Padang, Maumere, Jakarta, and Slamet Mountain for emergency response and contingency planning.

Creep strength of hastelloy X TIG-welded cylinder under internal pressure at elevated temperature

International Nuclear Information System (INIS)

Udoguchi, Teruyoshi; Indo, Hirosato; Isomura, Kazuyuki; Kobatake, Kiyokazu; Nakanishi, Tsuneo.

1981-01-01

Creep tests on circumferentially TIG-welded Hastelloy x cylinders were carried out under internal pressure for the investigation of structural behavior of welded components in high temperature environment. The creep rupture strength of TIG-welded cylinders was much lower than that of non-welded cylinders, while such reduction was not found in uniaxial creep tests on TIG-welded bars. It was deduced that the reduction was due to the low ductility (ranging from 1 to 5%) of the weld metal to which enhanced creep was induced by the adjacent base metal whose creep strain rate was much higher than that of the weld metal. Therefore, uniaxial creep tests on bar specimens is not sufficient for proper assessment of the creep rupture strength of welded components. Both creep strain rate and creep ductility should be concerned for the assessment. Creep tests by using components such as cylinder under internal pressure are recommendable for the confirmation of creep strength of welded structures and components. (author)

Statistical analysis of the low-temperature dislocation peak of internal friction (Bordoni peak) in nanostructured copper

International Nuclear Information System (INIS)

Vatazhuk, E.N.; Natsik, V.D.

2011-01-01

The temperature-frequency dependence of internal friction in the nanostructured samples of Cu and fibred composite C-32 vol.%Nb with the sizes of structure fragments approx 200 nm is analyzed. Experiments are used as initial information for such analysis. The characteristic for the heavily deformed copper Bordoni peak, located nearby a temperature 90 K, was recorded on temperature dependence of vibration decrement (frequencies 73-350 kHz) in previous experiments. The peak is due to the resonance interaction of sound with the system of thermal activated relaxators, and its width considerably greater in comparison with the width of standard internal friction peak with the single relaxation time. Statistical analysis of the peak is made in terms of assumption that the reason of broadening is random activation energy dispersion of relaxators as a result of intense distortion of copper crystal structure. Good agreement of experimental data and Seeger theory considers thermal activated paired kinks at linear segments of dislocation lines, placed in potential Peierls relief valley, as relaxators of Bordoni peak, was established. It is shown that the registered peak height in experiment correspond to presence at the average one dislocation segment in the interior of crystalline grain with size of 200 nm. Empirical estimates for the critical Peierls stress σp ∼ 2x10 7 Pa and integrated density of the interior grain dislocations ρ d ∼ 10 13 m -2 are made. Nb fibers in the composite Cu-Nb facilitate to formation of nanostructured copper, but do not influence evidently on the Bordoni peak.

7th International Topical Meeting on High Temperature Reactor Technology: The modular HTR is advancing towards reality. Papers and Presentations

International Nuclear Information System (INIS)

2014-01-01

HTR2014 aimed at providing an international platform for researchers, engineers and industrial professionals to share their innovative ideas, valuable experience and recent progresses on high temperature gas-cooled reactor (HTR) and its application technologies.

A newly developed container for safe, easy, and cost-effective overnight transportation of tissues and organs by electrically keeping tissue or organ temperature at 3 to 6°C.

Science.gov (United States)

Ohkawara, H; Kitagawa, T; Fukushima, N; Ito, T; Sawa, Y; Yoshimine, T

2012-05-01

As there is only one skin procurement organization in Japan the Japan Skin Bank Network (JSBN), all skin grafts procured in Japan are sent by a commercialized delivery system. Preliminarily, bottles containing saline were transported in a cardboard box using a so-called "cooled home delivery service" using a truck with a refrigerated cargo container. During transportation the temperature in the cardboard box increased to 18°C in summer and decreased to -5°C in winter. For these reasons, we investigated whether a newly developed container "Medi Cube" would be useful to transport skin grafts. Four bottles with a capacity of 300 mL containing 150 mL of saline in a Medi Cube container were transported from Osaka to the JSBN in Tokyo between 4 PM and 10 AM using a commercialized cooled home delivery service. Two bottles were transported in a Medi Cube container without phase change materials (PCM) in winter and summer, respectively. Another two bottles were transported in the Medi Cube with PCMs in winter. The temperatures inside saline, inside a transportation container, and outside the container, and air temperature were monitored continuously with a recordable thermometer. The temperatures inside saline and inside a Medi Cube container were maintained between 3 and 6°C, even when the temperature outside the container increased during parking. The temperature inside a Medi Cube container without PCM decreased to -3°C when the inside of the cargo container was overcooled in winter. However, the temperatures inside saline and inside a Medi Cube container with PCM were between 3 and 6°C, even when the temperature outside the container decreased to below 0°C in winter. A Medi Cube container with PCM provided a safe, easy, and cost-effective method for overnight transportation of skin grafts. Copyright © 2012 Elsevier Inc. All rights reserved.

International Space Station Environmental Control and Life Support System Acceptance Testing for Node 1 Temperature and Humidity Control Subsystem

Science.gov (United States)

Williams, David E.

2011-01-01

The International Space Station (ISS) Node 1 Environmental Control and Life Support (ECLS) System is comprised of five subsystems: Atmosphere Control and Storage (ACS), Atmosphere Revitalization (AR), Fire Detection and Suppression (FDS), Temperature and Humidity Control (THC), and Water Recovery and Management (WRM). This paper will provide a summary of the Node 1 ECLS THC subsystem design and a detailed discussion of the ISS ECLS Acceptance Testing methodology utilized for this subsystem.The International Space Station (ISS) Node 1 Environmental Control and Life Support (ECLS) System is comprised of five subsystems: Atmosphere Control and Storage (ACS), Atmosphere Revitalization (AR), Fire Detection and Suppression (FDS), Temperature and Humidity Control (THC), and Water Recovery and Management (WRM). This paper will provide a summary of the Node 1 ECLS THC subsystem design and a detailed discussion of the ISS ECLS Acceptance Testing methodology utilized for this subsystem.

The inherently-safe power reactor DYONISOS (Dynamic Nuclear Inherently-Safe Reactor Operating with Spheres)

International Nuclear Information System (INIS)

Taube, M.; Lanfranchi, M.; Weissenfluh, Th. von; Ligou, J.; Yadigaroglu, G.; Taube, P.

1986-01-01

A philosophy of inherent safety is formulated and an inherently-safe thermal power reactor is presented. Solid fuel in the form of spheres a few centimetres in diameter is suspended under the hydro-dynamic pressure of molten lead coolant in vertical channels within the graphite moderator. Loss of main pump pressure, or a loss-of-coolant accident (LOCA), results in immediate removal of the fuel to rigid sieves below the core, with consequent subcriticality. Residual and decay heat are carried away by thermal conduction through the coolant or, in the case of a LOCA, by a combination of radiation and natural convection of cover gas or incoming air from the fuel to the reactor vessel and convection of air between the vessel and steel containment wall. All decay heat removal systems are passive, though actively initiated external spray cooling of the containment can be used to reduce wall temperature. This, however, is only necessary in the case of a LOCA and after a period of 24 h. (author)

Making Our Food Safe

International Nuclear Information System (INIS)

Madsen, Michael

2013-01-01

Full text: As civilization has progressed societies have strived to make food safer; from using fire to cook our food, and boiling our water to make it safe to drink, advances in technology have helped kill microorganisms that can make food unsafe. The FAO/IAEA Joint Division helps provide technical assistance to Member States that want to implement irradiation technology in making their food safer. Food and waterborne diarrhoeal diseases are estimated to kill roughly 2.2 million people annually, of which 1.9 million are children. Irradiating some of the foods we eat can save many of these lives by reducing the risk of food poisoning and killing the organisms that cause disease. Irradiation works by treating food with a small dose of ionizing radiation, this radiation disrupts the bacteria’s DNA and cell membranes structure stopping the organism from reproducing or functioning, but does not make the food radioactive. It can be applied to a variety of foods from spices and seasonings, to fruits and vegetables and is similar to pasteurization, but without the need for high temperatures that might impair food quality. (author)

Steering teens safe: a randomized trial of a parent-based intervention to improve safe teen driving.

Science.gov (United States)

Peek-Asa, Corinne; Cavanaugh, Joseph E; Yang, Jingzhen; Chande, Vidya; Young, Tracy; Ramirez, Marizen

2014-07-31

Crashes are the leading cause of death for teens, and parent-based interventions are a promising approach. We assess the effectiveness of Steering Teens Safe, a parent-focused program to increase safe teen driving. Steering Teens Safe aimed to improve parental communication with teens about safe driving using motivational interviewing techniques in conjunction with 19 safe driving lessons. A randomized controlled trial involved 145 parent-teen dyads (70 intervention and 75 control). Intervention parents received a 45-minute session to learn the program with four follow-up phone sessions, a DVD, and a workbook. Control parents received a standard brochure about safe driving. Scores were developed to measure teen-reported quantity and quality of parental communication about safe driving. The main outcome measure was a previously validated Risky Driving Score reported by teens. Because the Score was highly skewed, a generalized linear model based on a gamma distribution was used for analysis. Intervention teens ranked their parent's success in talking about driving safety higher than control teens (p = 0.035) and reported that their parents talked about more topics (non-significant difference). The Risky Driving Score was 21% lower in intervention compared to control teens (85% CI = 0.60, 1.00). Interaction between communication quantity and the intervention was examined. Intervention teens who reported more successful communication had a 42% lower Risky Driving Score (95% CI = 0.37, 0.94) than control parents with less successful communication. This program had a positive although not strong effect, and it may hold the most promise in partnership with other programs, such as Driver's Education or Graduated Driver's License policies. ClinicalTrials.gov NCT01014923. Registered Nov. 16, 2009.

Staying Safe in the Water

Centers for Disease Control (CDC) Podcasts

In this podcast, Dr. Julie Gilchrist, a pediatrician and medical epidemiologist from CDC’s Injury Center, talks about staying safe in the water. Tips are for all audiences, with a focus on preventing drownings and keeping children safe in and around the pool, lake, or ocean.

Safe biodegradable fluorescent particles

Science.gov (United States)

Martin, Sue I [Berkeley, CA; Fergenson, David P [Alamo, CA; Srivastava, Abneesh [Santa Clara, CA; Bogan, Michael J [Dublin, CA; Riot, Vincent J [Oakland, CA; Frank, Matthias [Oakland, CA

2010-08-24

A human-safe fluorescence particle that can be used for fluorescence detection instruments or act as a safe simulant for mimicking the fluorescence properties of microorganisms. The particle comprises a non-biological carrier and natural fluorophores encapsulated in the non-biological carrier. By doping biodegradable-polymer drug delivery microspheres with natural or synthetic fluorophores, the desired fluorescence can be attained or biological organisms can be simulated without the associated risks and logistical difficulties of live microorganisms.

Heat transfer and thermodynamic performance of convective–radiative cooling double layer walls with temperature-dependent thermal conductivity and internal heat generation

International Nuclear Information System (INIS)

Torabi, Mohsen; Zhang, Kaili

2015-01-01

Highlights: • First and second laws of thermodynamics have been investigated in a composite wall. • Convective–radiative heat transfer is assumed on both surfaces. • Optimum interface location is calculated to minimize the total entropy generation rate. • Thermal conductivities ratio has great effects on the temperature and entropy generation. - Abstract: Composite geometries have numerous applications in industry and scientific researches. This work investigates the temperature distribution, and local and total entropy generation rates within two-layer composite walls using conjugate convection and radiation boundary conditions. Thermal conductivities of the materials of walls are assumed temperature-dependent. Temperature-dependent internal heat generations are also incorporated into the modeling. The differential transformation method (DTM) is used as an analytical technique to tackle the highly nonlinear system of ordinary differential equations. Thereafter, the local and total entropy generation rates are calculated using the DTM formulated temperature distribution. An exact analytical solution, for the temperature-independent model without radiation effect, is also derived. The correctness and accuracy of the DTM solution are checked against the exact solution. After verification, effects of thermophysical parameters such as location of the interface, convection–conduction parameters, radiation–conduction parameters, and internal heat generations, on the temperature distribution, and both local and total entropy generation rates are examined. To deliver the minimum total entropy generation rate, optimum values for some parameters are also found. Since composite walls are widely used in many fields, the abovementioned investigation is a beneficial tool for many engineering industries and scientific fields to minimize the entropy generation, which is the exergy destruction, of the system

Safe Haven.

Science.gov (United States)

Bush, Gail

2003-01-01

Discusses school libraries as safe havens for teenagers and considers elements that foster that atmosphere, including the physical environment, lack of judgments, familiarity, leisure, and a welcoming nature. Focuses on the importance of relationships, and taking the time to listen to teens and encourage them. (LRW)

Internally generated natural variability of global-mean temperatures

International Nuclear Information System (INIS)

Wigley, T.M.L.; Raper, S.C.B.

1990-01-01

Quantitative frequency-domain and time-domain estimates are made of an important aspect of natural variability of global-mean temperatures, namely, passive internal variability resulting from the modulation of atmospheric variability by the ocean. The results are derived using an upwelling-diffusion, energy-balance climate model. In the frequency domain, analytical spectral results show a transition from a high-frequency region in which the response is determined by the mixed-layer heat capacity and is independent of the climate sensitivity (time scales less than around 10 years), to a low-frequency region in which the response depends only on the climate sensitivity. In the former region the spectral power is proportional to f -2 , where f is the frequency, while in the latter the power is independent of frequency. The range of validity of these results depends on the components of the climate system that are included in the model. In this case these restrict the low-frequency results to time scales less than about 1,000 years. A qualitative extrapolation is presented in an attempt to explain the observed low-frequency power spectra from deep-sea-core δ 18 O time series. The spectral results are also used to estimate the effective heat capacity of the ocean as a function of frequency. At low frequencies, this can range up to 50 times greater than the heat capacity of the mixed layer. Results in the time domain are obtained by solving the model equations numerically

Nursing care update: Internal radiation therapy

International Nuclear Information System (INIS)

Lowdermilk, D.L.

1990-01-01

Internal radiation therapy has been used in treating gynecological cancers for over 100 years. A variety of radioactive sources are currently used alone and in combination with other cancer treatments. Nurses need to be able to provide safe, comprehensive care to patients receiving internal radiation therapy while using precautions to keep the risks of exposure to a minimum. This article discusses current trends and issues related to such treatment for gynecological cancers.20 references

International Surface Temperature Initiative (ISTI) Global Land Surface Temperature Databank - Stage 3 Monthly

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Global Land Surface Temperature Databank contains monthly timescale mean, maximum, and minimum temperature for approximately 40,000 stations globally. It was...

Influence of changes in humidity on dry temperature in GPS RO climatologies

Directory of Open Access Journals (Sweden)

J. Danzer

2014-09-01

. As a consequence, we performed a model study, investigating the increase in height of the transition region between moist and dry air. We used data from the fifth phase of the Coupled Model Intercomparison Project (CMIP5, analyzing again monthly mean dry temperature to physical temperature differences, now from the years 2006 to 2050. We used the highest emission scenario RCP8.5 (representative concentration pathway, studying all available models of the CMIP5 project, analyzing one internal run per model, with the goal to identify the altitude region where trends in dry temperature can be safely regarded as reflecting trends in physical temperature. From all models we therefore choose a selection of models ("max 8" CMIP5 models, which showed the largest trend differences. As a result, our trend study suggests that the lower boundary of the region where dry temperature is essentially equal to physical temperature rises about 150 m decade−1.

Analysis of Effective and Internal Cyclic Stress Components in the Inconel Superalloy Fatigued at Elevated Temperature

Czech Academy of Sciences Publication Activity Database

Šmíd, Miroslav; Petrenec, Martin; Polák, Jaroslav; Obrtlík, Karel; Chlupová, Alice

2011-01-01

Roč. 278, 4 July (2011), s. 393-398 ISSN 1022-6680. [European Symposium on Superalloys and their Application. Wildbad Kreuth, 25.5.2010-28.5.2010] R&D Projects: GA ČR GA106/08/1631 Institutional research plan: CEZ:AV0Z20410507 Keywords : low cycle fatigue * superalloys * high temperature * hysteresis loop * effective and internal stresses Subject RIV: JL - Materials Fatigue, Friction Mechanics; JL - Materials Fatigue, Friction Mechanics (UFM-A)

International Surface Temperature Initiative (ISTI) Global Land Surface Temperature Databank - Stage 2 Daily

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The global land surface temperature databank contains monthly timescale mean, max, and min temperature for approximately 40,000 stations globally. It was developed...

International Surface Temperature Initiative (ISTI) Global Land Surface Temperature Databank - Stage 2 Monthly

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The global land surface temperature databank contains monthly timescale mean, max, and min temperature for approximately 40,000 stations globally. It was developed...

International Surface Temperature Initiative (ISTI) Global Land Surface Temperature Databank - Stage 1 Monthly

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The global land surface temperature databank contains monthly timescale mean, max, and min temperature for approximately 40,000 stations globally. It was developed...

International Surface Temperature Initiative (ISTI) Global Land Surface Temperature Databank - Stage 1 Daily

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The global land surface temperature databank contains monthly timescale mean, max, and min temperature for approximately 40,000 stations globally. It was developed...

Potential safe termination by injection of polypropylene pellets in JET

International Nuclear Information System (INIS)

Schmidt, G.L.; Ali-Arshad, S.; Bartlett, D.

1995-01-01

Thermal energy and the magnetic field energy associated with the plasma current must be dissipated safely when a tokamak discharge is terminated in a disruption. Magnetic energy can be dissipated by impurity radiation if position control is maintained. Prior to the dissipation of magnetic energy, thermal energy is usually conducted to the plasma contact points on a 1ms time scale in a thermal quench. A resistive, highly radiating plasma formed prior to the thermal quench, might dissipate both the thermal and magnetic energy by radiation minimizing damage due to local deposition. High speed injection of a low Z material can produce a resistive, highly radiating plasma on a 1ms time scale. Neon has recently been used in such an application on JT60-U. A large carbon pellet producing dilution temperatures < 1 keV is a possible alternative. This paper summarizes the results of an initial experiment performed in JET using carbon injected at high speed, as a 6mm polypropylene pellet, to investigate this potential approach to a safe plasma termination

Aflatoxins & Safe Storage

Directory of Open Access Journals (Sweden)

Philippe eVillers

2014-04-01

Full Text Available The paper examines both field experience and research on the prevention of the exponential growth of aflatoxins during multi-month post harvest storage in hot, humid countries. The approach described is the application of modern safe storage methods using flexible, Ultra Hermetic™ structures that create an unbreatheable atmosphere through insect and microorganism respiration alone, without use of chemicals, fumigants, or pumps. Laboratory and field data are cited and specific examples are given describing the uses of Ultra Hermetic storage to prevent the growth of aflatoxins with their significant public health consequences. Also discussed is the presently limited quantitative information on the relative occurrence of excessive levels of aflatoxin (>20 ppb before versus after multi-month storage of such crops as maize, rice and peanuts when under high humidity, high temperature conditions and, consequently, the need for further research to determine the frequency at which excessive aflatoxin levels are reached in the field versus after months of post-harvest storage. The significant work being done to reduce aflatoxin levels in the field is mentioned, as well as its probable implications on post harvest storage. Also described is why, with some crops such as peanuts, using Ultra Hermetic storage may require injection of carbon dioxide or use of an oxygen absorber as an accelerant. The case of peanuts is discussed and experimental data is described.

More than a Safe Space

Science.gov (United States)

Sadowski, Michael

2016-01-01

Over the past three decades, much of the conversation about LGBTQ students in schools has centered on safety--anti-bullying policies, the "safe space" of gay-straight alliances, and "safe zones" marked by rainbow-colored stickers on classroom doors. In this article, Michael Sadowski argues that it's time to move beyond safety…

Safe injection procedures, injection practices, and needlestick ...

African Journals Online (AJOL)

Results: Safe injection procedures regarding final waste disposal were sufficiently adopted, while measures regarding disposable injection equipment, waste containers, hand hygiene, as well as injection practices were inadequately carried out. Lack of job aid posters that promote safe injection and safe disposal of ...

Main corrective measures in an early phase of nuclear power plants’ preparation for safe long term operation

Energy Technology Data Exchange (ETDEWEB)

Krivanek, Robert, E-mail: r.krivanek@iaea.org [International Atomic Energy Agency (IAEA), Department of Nuclear Safety and Security, Operational Safety Section, Vienna 1400 (Austria); Fiedler, Jan, E-mail: fiedler@fme.vutbr.cz [University of Technology Brno, Faculty of Mechanical Engineering, Energy Institute, Technická 2896/2, 616 69 Brno (Czech Republic)

2017-05-15

Highlights: • Results of SALTO missions provide the most important issues for safe long term operation (LTO) of nuclear power plants. • The most important technical corrective measures in an early phase of preparation for safe LTO are described. • Their satisfactory resolution creates a basis for further activities to demonstrate preparedness for safe LTO. - Abstract: This paper presents the analysis of main technical deficiencies of nuclear power plants (NPPs) in preparedness for safe long term operation (LTO) and the main corrective measures in an early phase of preparation for safe LTO of NPPs. It focuses on technical aspects connected with management of physical ageing of NPP structures, systems and components (SSCs). It uses as a basis results of IAEA SALTO missions performed between 2005 and 2016 (see also paper NED8805 in Nuclear Engineering and Design in May 2016) and the personal experiences of the authors with preparation of NPPs for safe LTO. This paper does not discuss other important aspects of safe LTO of NPPs, e.g. national nuclear energy policies, compliance of NPPs with the latest international requirements on design, obsolescence, environmental impact and economic aspects of LTO. Chapter 1 provides a brief introduction of the current status of the NPP’ fleet in connection with LTO. Chapter 2 provides an overview of SALTO peer review service results with a focus on deficiencies related to physical ageing of safety SSCs and a demonstration that SSCs will perform their safety function during the intended period of LTO. Chapter 3 discusses the main corrective measures which NPPs typically face during the preparation for demonstration of safe LTO. Chapter 4 summarizes the current status of the NPP’ fleet in connection with LTO and outlines further steps needed in preparation for safe LTO.

Guidelines for safe design of shipping packages against brittle fracture

International Nuclear Information System (INIS)

1993-08-01

In 1992, the ninth meeting of the Standing Advisory Group on the Safe Transport of Radioactive Materials recommended the publication of this TECDOC in an effort to promote the widest debate on the criteria for the brittle fracture safe design of transport packages. The published IAEA advice on the influence of brittle fracture on material integrity is contained in Appendix IX of the Advisory Material for the IAEA Regulations for the Safety Transport of Radioactive Material (1985 Edition, as amended 1990), Safety Series No. 37. This guidance is limited in scope, dealing only with ferritic steels in general terms. It is becoming more common for designers to specify materials other than austenitic stainless steel for packaging components. The data on ferritic steels cannot be assumed to apply to other metals, hence the need for further guidance on the development of relationships describing material properties at low temperatures. The methods described in this TECDOC will be considered by the Revision Panel for inclusion in the 1996 Edition of the IAEA Regulations for the Safe Transport of Radioactive Material and the supporting documents. If accepted by the Revision Panel, this advice will be a candidate for upgrading to a Safety Practice. In the interim period, this TECDOC offers provisional advice on brittle fracture evaluation. It is acknowledged that, at this stage, the views expressed do not necessarily reflect those of the governments of Member States or organizations under whose auspices this manuscript was produced. Refs and figs

Managing Cassini Safe Mode Attitude at Saturn

Science.gov (United States)

Burk, Thomas A.

2010-01-01

The Cassini spacecraft was launched on October 15, 1997 and arrived at Saturn on June 30, 2004. It has performed detailed observations and remote sensing of Saturn, its rings, and its satellites since that time. In the event safe mode interrupts normal orbital operations, Cassini has flight software fault protection algorithms to detect, isolate, and recover to a thermally safe and commandable attitude and then wait for further instructions from the ground. But the Saturn environment is complex, and safety hazards change depending on where Cassini is in its orbital trajectory around Saturn. Selecting an appropriate safe mode attitude that insures safe operation in the Saturn environment, including keeping the star tracker field of view clear of bright bodies, while maintaining a quiescent, commandable attitude, is a significant challenge. This paper discusses the Cassini safe table management strategy and the key criteria that must be considered, especially during low altitude flybys of Titan, in deciding what spacecraft attitude should be used in the event of safe mode.

The continuous review and periodic revision process for the International Atomic Energy Agencies regulations for the safe transport of radioactive materials - A status report

International Nuclear Information System (INIS)

O'Sullivan, R.A.; Pettersson, B.G.; Pope, R.B.

1989-01-01

The International Atomic Energy Agencies (IAEA) Regulations for the Safe Transport of Radioactive Material, Safety Series No.6 (hereinafter denoted as the Regulations) have developed into the model for international modal organization and individual country regulations (and other regulatory-related documentation) controlling the packaging and transportation of radioactive materials. The Regulations were initially developed in 1961 and have been periodically revised since then. Revised editions of the Regulations, accounting for developments in technology and shipping practices, were issued in 1965, 1967, 1973 (also, an amended 1973 Edition was issued in 1979), and in 1985. The process of developing these documents has been performed on a cooperative basis utilizing inputs from various member states of the IAEA and from other interested international organizations. The latest comprehensive revision of the Regulations and its supportive documents was initiated in 1979, and culminated in the 1985 Edition of the Regulations. This was the first complete revision to be published since 1973 (except for the amended Edition thereto being issued in 1979). During the process which led to the 1985 Edition of the Regulations and its supportive documents, it became apparent that changes needed to be made in this process. Not addressing issues related to transportation regulations on a continuing basis created many difficulties in trying to efficiently and acceptably review and revise these documents in a short period of time. The purpose of this paper is to outline the review/revision process which was established, to summarize the results from that process so far (in terms of changes that have been made to the 1985 Edition through supplements thereto), and to discuss current plans for carrying on with the review/revision process with slight modifications

A fail-safe microprocessor-based protection system utilising low-level multiplexed sensor signals

International Nuclear Information System (INIS)

Orme, S.; Evans, N.J.; Wey, B.O.

1985-01-01

The paper describes a fail-safe reactor protection system, called the individual sub-assembly temperature monitoring system (ISAT). It is being developed for the commercial demonstration fast reactor. The system incorporates recent advances in solid-state electronics and in particular microprocessors to implement time-shared data acquisition techniques to obtain and process data from around 1400 fast response thermocouples whilst meeting the required levels for reliability and availability. (author)

Key convention on safe management of spent fuel and radioactive waste to enter into force

International Nuclear Information System (INIS)

2001-01-01

At a ceremony at IAEA Headquarters today, Ireland deposited its instrument of ratification to an important convention on the safe management of spent fuel and radioactive waste, thereby ensuring its entry into force. The Convention will be the first international instrument to address the safety of management and storage of radioactive wastes and spent fuels in countries with and without nuclear programmes

Sustainable access to safe drinking water: fundamental human right in the international and national scene

Directory of Open Access Journals (Sweden)

Celso Maran de Oliveira

2017-12-01

Full Text Available Access to potable water is absolutely essential to the maintenance of life, as well as to provide regular exercise of other human rights. The lack of access to water in sufficient quantity or access to non-potable water may cause serious and irreparable damage to people. This paper investigates the evolution of international and national recognition of this fundamental human right, whether implicit or explicit. This was accomplished by the study of international human rights treaties, bibliographic information on water resources and their corresponding legal systems, national and international. The results suggest that sustainable access to drinking water is a fundamental human right in the context of international relations and the State. Further, even without explicitly stating this right in the Constitution of 1988, Brazil has incorporated the main international provisions on the subject, but this right must be acknowledged according to the principles of non-typical fundamental rights and the dignity of the human person. This right should be universally guaranteed by the Government in sufficient quantity and quality, regardless of the economic resources of individuals.

Conceptual design of a passively safe thorium breeder Pebble Bed Reactor

International Nuclear Information System (INIS)

Wols, F.J.; Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der

2015-01-01

Highlights: • This work proposes three possible designs for a thorium Pebble Bed Reactor. • A high-conversion PBR (CR > 0.96), passively safe and within practical constraints. • A thorium breeder PBR (220 cm core) in practical regime, but not passively safe. • A passively safe breeder, requiring higher fuel reprocessing and recycling rates. - Abstract: More sustainable nuclear power generation might be achieved by combining the passive safety and high temperature applications of the Pebble Bed Reactor (PBR) design with the resource availability and favourable waste characteristics of the thorium fuel cycle. It has already been known that breeding can be achieved with the thorium fuel cycle inside a Pebble Bed Reactor if reprocessing is performed. This is also demonstrated in this work for a cylindrical core with a central driver zone, with 3 g heavy metal pebbles for enhanced fission, surrounded by a breeder zone containing 30 g thorium pebbles, for enhanced conversion. The main question of the present work is whether it is also possible to combine passive safety and breeding, within a practical operating regime, inside a thorium Pebble Bed Reactor. Therefore, the influence of several fuel design, core design and operational parameters upon the conversion ratio and passive safety is evaluated. A Depressurized Loss of Forced Cooling (DLOFC) is considered the worst safety scenario that can occur within a PBR. So, the response to a DLOFC with and without scram is evaluated for several breeder PBR designs using a coupled DALTON/THERMIX code scheme. With scram it is purely a heat transfer problem (THERMIX) demonstrating the decay heat removal capability of the design. In case control rods cannot be inserted, the temperature feedback of the core should also be able to counterbalance the reactivity insertion by the decaying xenon without fuel temperatures exceeding 1600 °C. Results show that high conversion ratios (CR > 0.96) and passive safety can be combined in

Varying influences of motivation factors on employees' likelihood to perform safe food handling practices because of demographic differences.

Science.gov (United States)

Ellis, Jason D; Arendt, Susan W; Strohbehn, Catherine H; Meyer, Janell; Paez, Paola

2010-11-01

Food safety training has been the primary avenue for ensuring food workers are performing proper food handling practices and thus, serving safe food. Yet, knowledge of safe food handling practices does not necessarily result in actual performance of these practices. This research identified participating food service employees' level of agreement with four factors of motivation (internal motivations, communication, reward-punishment, and resources) and determined if respondents with different demographic characteristics reported different motivating factors. Data were collected from 311 food service employees who did not have any supervisory responsibilities. Intrinsic motivation agreement scores were consistently the highest of all four motivational factors evaluated and did not differ across any of the demographic characteristics considered. In contrast, motivation agreement scores for communication, reward-punishment, and resources did differ based on respondents' gender, age, place of employment, job status, food service experience, completion of food handler course, or possession of a food safety certification. In general, respondents agreed that these motivation factors influenced their likelihood to perform various safe food handling procedures. This research begins to illustrate how employees' demographic characteristics influence their responses to various motivators, helping to clarify the complex situation of ensuring safe food in retail establishments. Future research into why employee willingness to perform varies more for extrinsic motivation than for intrinsic motivation could assist food service managers in structuring employee development programs and the work environment, in a manner that aids in improving external motivation (communication, reward-punishment, and resources) and capitalizing on internal motivation.

EM International, July 1994, Volume 2

International Nuclear Information System (INIS)

1994-01-01

The Office of Environmental Management (EM) at the Department of Energy (DOE) is seeking out and leveraging foreign technology, data, and resources in keeping with EM's mandate to protect public health and the environment through the safe and cost-effective remediation of the Department's nuclear weapons sites. EM works closely with foreign governments, industry, and universities to obtain innovative environmental technologies, scientific and engineering expertise, and operations experience that will support EM's objectives. Where appropriate, these international resources are used to manage the more urgent risks at our sites, secure a safe workplace, help build consensus on critical issues, and strengthen our technology development program. Through international agreements EM engages in cooperative exchange of information, technology, and individuals. Currently, we are managing agreements with a dozen countries in Europe, Latin America, and Asia. These agreements focus on environmental restoration, waste management, transportation of radioactive wastes, and decontamination and decommissioning. This publication contains the following articles: in situ remediation integrated program; in-situ characterization and inspection of tanks; multimedia environmental pollutant assessment system (MEPAS); LLNL wet oxidation -- AEA technology. Besides these articles, this publication covers: EU activities with Russia; technology transfer activities; and international organization activities

Dementia - keeping safe in the home

Science.gov (United States)

... this page: //medlineplus.gov/ency/patientinstructions/000031.htm Dementia - keeping safe in the home To use the ... make sure the homes of people who have dementia are safe for them. Safety Tips for the ...

Safeguards Automated Facility Evaluation (SAFE) methodology

International Nuclear Information System (INIS)

Chapman, L.D.; Grady, L.M.; Bennett, H.A.; Sasser, D.W.; Engi, D.

1978-01-01

The SAFE procedure is an efficient method of evaluating the physical protection system of a nuclear facility. Since the algorithms used in SAFE for path generation and evaluation are analytical, many paths can be evaluated with a modest investment in computer time. SAFE is easy to use because the information required is well-defined and the interactive nature of this procedure lends itself to straightforward operation. The modular approach that has been taken allows other functionally equivalent modules to be substituted as they become available. The SAFE procedure has broad applications in the nuclear facility safeguards field as well as in the security field in general. Any fixed facility containing valuable materials or components to be protected from theft or sabotage could be analyzed using this same automated evaluation technique

A new lithium-ion battery internal temperature on-line estimate method based on electrochemical impedance spectroscopy measurement

Science.gov (United States)

Zhu, J. G.; Sun, Z. C.; Wei, X. Z.; Dai, H. F.

2015-01-01

The power battery thermal management problem in EV (electric vehicle) and HEV (hybrid electric vehicle) has been widely discussed, and EIS (electrochemical impedance spectroscopy) is an effective experimental method to test and estimate the status of the battery. Firstly, an electrochemical-based impedance matrix analysis for lithium-ion battery is developed to describe the impedance response of electrochemical impedance spectroscopy. Then a method, based on electrochemical impedance spectroscopy measurement, has been proposed to estimate the internal temperature of power lithium-ion battery by analyzing the phase shift and magnitude of impedance at different ambient temperatures. Respectively, the SoC (state of charge) and temperature have different effects on the impedance characteristics of battery at various frequency ranges in the electrochemical impedance spectroscopy experimental study. Also the impedance spectrum affected by SoH (state of health) is discussed in the paper preliminary. Therefore, the excitation frequency selected to estimate the inner temperature is in the frequency range which is significantly influenced by temperature without the SoC and SoH. The intrinsic relationship between the phase shift and temperature is established under the chosen excitation frequency. And the magnitude of impedance related to temperature is studied in the paper. In practical applications, through obtaining the phase shift and magnitude of impedance, the inner temperature estimation could be achieved. Then the verification experiments are conduced to validate the estimate method. Finally, an estimate strategy and an on-line estimation system implementation scheme utilizing battery management system are presented to describe the engineering value.

Admission body temperature predicts long-term mortality after acute stroke

DEFF Research Database (Denmark)

Kammersgaard, L P; Jørgensen, H S; Rungby, Jørgen

2002-01-01

Body temperature is considered crucial in the management of acute stroke patients. Recently hypothermia applied as a therapy for stroke has been demonstrated to be feasible and safe in acute stroke patients. In the present study, we investigated the predictive role of admission body temperature...

Selection of exception limits for all actinide nuclides based on revised criteria for safe international transport

International Nuclear Information System (INIS)

Lavarenne, C.; Rouyer, V.; Sert, G.; Mennerdahl, D.; Dean, C.; Barton, N.; Jean, F.

2003-01-01

Since 1998, there have been some speculations about future transport of significant quantities and concentrations of other actinide nuclides than the four currently listed in the regulation for the safe transport of the radioactive material. Therefore, it raised a need to specify exception limits for such actinides. Additionally, the total fissile nuclide mass per consignment of excepted packages was limited in the 1996 edition of the regulations (a conveyance limit is preliminary supported in the 2003 revision). The proposed changes of the rules have to take this new control into account. The European Community (DGTREN) decided to fund a project related to this subject. In order to define credible exception limits, it was necessary to have reasonably accurate data for all actinide nuclides. Then the authors of the study decided to perform calculations with different codes (MONK, MCNP, CRISTAL, SCALE) and different cross-section libraries (JEF2.2, ENDFB, JENDL, etc.). This article presents the work achieved and gives propositions of modification for the IAEA requirements for the Safe Transport of Radioactive Material related to, firstly, the list of the fissile materials, and secondly, the rule to determine the quantities of actinide nuclides that can be excepted from the requirements for the packages containing fissile materials. The participants acknowledge the DGTREN who made this work possible due to its support. (author)

Breastfeeding FAQs: Safely Storing Breast Milk

Science.gov (United States)

... Search English Español Breastfeeding FAQs: Safely Storing Breast Milk KidsHealth / For Parents / Breastfeeding FAQs: Safely Storing Breast ... may have. How do I store my breast milk? You can freeze and/or refrigerate your pumped ( ...

Microbes safely, effectively bioremediate oil field pits

International Nuclear Information System (INIS)

Shaw, B.; Block, C.S.; Mills, C.H.

1995-01-01

Natural and augmented bioremediation provides a safe, environmental, fast, and effective solution for removing hydrocarbon stains from soil. In 1992, Amoco sponsored a study with six bioremediation companies, which evaluated 14 different techniques. From this study, Amoco continued using Environmental Protection Co.'s (EPC) microbes for bioremediating more than 145 sites near Farmington, NM. EPC's microbes proved effective on various types of hydrocarbon molecules found in petroleum stained soils from heavy crude and paraffin to volatiles such as BTEX (benzene, toluene, ethylbenzene, xylene) compounds. Controlled laboratory tests have shown that these microbes can digest the hydrocarbon molecules with or without free oxygen present. It is believed that this adaptation gives these microbes their resilience. The paper describes the bioremediation process, environmental advantages, in situ and ex situ bioremediation, goals of bioremediation, temperature effects, time, cost, and example sites that were treated

Curiosity's Autonomous Surface Safing Behavior Design

Science.gov (United States)

Neilson, Tracy A.; Manning, Robert M.

2013-01-01

The safing routines on all robotic deep-space vehicles are designed to put the vehicle in a power and thermally safe configuration, enabling communication with the mission operators on Earth. Achieving this goal is made a little more difficult on Curiosity because the power requirements for the core avionics and the telecommunication equipment exceed the capability of the single power source, the Multi-Mission Radioisotope Thermoelectric Generator. This drove the system design to create an operational mode, called "sleep mode", where the vehicle turns off most of the loads in order to charge the two Li-ion batteries. The system must keep the vehicle safe from over-heat and under-heat conditions, battery cell failures, under-voltage conditions, and clock failures, both while the computer is running and while the system is sleeping. The other goal of a safing routine is to communicate. On most spacecraft, this simply involves turning on the receiver and transmitter continuously. For Curiosity, Earth is above the horizon only a part of the day for direct communication to the Earth, and the orbiter overpass opportunities only occur a few times a day. The design must robustly place the Rover in a communicable condition at the correct time. This paper discusses Curiosity's autonomous safing behavior and describes how the vehicle remains power and thermally safe while sleeping, as well as a description of how the Rover communicates with the orbiters and Earth at specific times.

Advanced microsystems for automotive applications 2013 smart systems for safe and green vehicles

CERN Document Server

Meyer, Gereon

2013-01-01

The road vehicle of the future will embrace innovations from three major automotive technology fields: driver assistance systems, vehicle networking and alternative propulsion. Smart systems such as adaptive ICT components and MEMS devices, novel network architectures, integrated sensor systems, intelligent interfaces and functional materials form the basis of these features and permit their successful and synergetic integration. They increasingly appear to be the key enabling technologies for safe and green road mobility. For more than fifteen years the International Forum on Advanced Microsystems for Automotive Applications (AMAA) has been successful in detecting novel trends and in discussing the technological implications from early on. The topic of the AMAA 2013 will be “Smart Systems for Safe and Green Vehicles”. This book contains peer-reviewed papers written by leading engineers and researchers which all address the ongoing research and novel developments in the field. www.amaa.de.

Problems relating to international transport of nuclear fuels

International Nuclear Information System (INIS)

Timm, U.E.

1985-01-01

Owing to the tremendous geographic distances between uranium deposits of interest, to the various degrees of sophistication of nuclear industry in industrialized countries and to the close international cooperation in the field of nuclear energy, safe international transports, physical protection and transport handling play an important role. It is suggested to better coordinate the activities of nuclear power plant operators, the nuclear industry and specialized transport companies with respect to all national and international issues of nuclear fuel transports. (DG) [de

Removing Hair Safely

Science.gov (United States)

... For Consumers Home For Consumers Consumer Updates Removing Hair Safely Share Tweet Linkedin Pin it More sharing ... related to common methods of hair removal. Laser Hair Removal In this method, a laser destroys hair ...

Destruction mechanism of the internal structure in Lithium-ion batteries used in aviation industry

International Nuclear Information System (INIS)

Swornowski, Paweł J.

2017-01-01

In the article, the reasons for destruction of the internal structure in Lithium-ion batteries used in aviation industry have been explained. They manifest themselves in the battery's overheating, and in extreme cases they result in explosion. The report presents the results of experiments, which consisted in subjecting the tested Lithium-ion battery to vibration over a specified period of time and observing the changes of temperature inside it with the use of a thermal infrared camera. Another focal point of the study was the influence of vibrations on voltage change in relation to variable current load, and the influence of ambient temperature change on the Lithium-ion battery's voltage change. It has also been demonstrated that vibrations can damage the control electronics of the Lithium-ion battery. Moreover, the mechanism by which potentially dangerous thermal hot spots are formed in a Lithium-ion battery has been presented, as well as an uncertainty analysis of all measurement results. - Highlights: • The causes of internal destruction of Lithium-ion batteries are external vibrations. • The influence of vibrations on the change of a Lithium-ion battery's most parameters. • The mechanism leading to the explosion of a Lithium-ion battery was demonstrated. • The conclusions ensuring safe exploitation of a Lithium-ion battery were presented.

Battery Internal Temperature Estimation for LiFePO4 Battery Based on Impedance Phase Shift under Operating Conditions

Directory of Open Access Journals (Sweden)

Jiangong Zhu

2017-01-01

Full Text Available An impedance-based temperature estimation method is investigated considering the electrochemical non-equilibrium with short-term relaxation time for facilitating the vehicular application. Generally, sufficient relaxation time is required for battery electrochemical equilibrium before the impedance measurement. A detailed experiment is performed to investigate the regularity of the battery impedance in short-term relaxation time after switch-off current excitation, which indicates that the impedance can be measured and also has systematical decrement with the relaxation time growth. Based on the discussion of impedance variation in electrochemical perspective, as well as the monotonic relationship between impedance phase shift and battery internal temperature in the electrochemical equilibrium state, an exponential equation that accounts for both measured phase shift and relaxation time is established to correct the measuring deviation caused by electrochemical non-equilibrium. Then, a multivariate linear equation coupled with ambient temperature is derived considering the temperature gradients between the active part and battery surface. Equations stated above are all identified with the embedded thermocouple experimentally. In conclusion, the temperature estimation method can be a valuable alternative for temperature monitoring during cell operating, and serve the functionality as an efficient implementation in battery thermal management system for electric vehicles (EVs and hybrid electric vehicles (HEVs.

LEADIR-PS: the path to a safe and economic SMR

Energy Technology Data Exchange (ETDEWEB)

Hart, R.S. [Nothern Nuclear Industries Inc., Cambridge, Ontario (Canada)

2014-07-01

Northern Nuclear Industries Incorporated (N{sup 2} I{sup 2}) is developing a family of Small Modular Reactors (SMRs) called LEADIR-PS, an acronym for LEAD-cooled Integral Reactor-Passively Safe. LEADIR-PS plants under development, focused on process heat applications and the energy demands of Canada, are the LEADIR-PS100 with an output of 100 MWth and LEADIR-PS300 with an output of 300 MWth. A plant consisting of six LEADIR-PS300 reactor modules serving a common turbine-generator, called the LEADIR-PS Six-Pack, is focused on serving areas with higher energy demands. LEADIR-PS integrates the inherent safety features of the Modular High Temperature Gas Reactor and molten lead coolant in an integral pool type reactor configuration. Molten lead coolant, which boils at 1750 {sup o}C,avoids the cost of a reactor pressure vessel and high pressure/high temperature reactor coolant systems, and the safety concerns regarding pressure vessel and large capacity reactor coolant system piping rupture and precludes evaporation of the coolant. Molten lead does not chemically react with air, water, or graphite. The Gen IV+ LEADIR-PS plants are inherently/passively safe. There are no active systems required for safe shutdown and decay heat removal. Safety is assured without active or stored energy power supply, without a requirement to reposition valves or other devices and operator intervention or action. The unprecedented safety achieved by LEADIR-PS reactors avoids requirements for a large exclusion radius and demanding evacuation plan requirements. LEADIR-PS, with steam conditions of 370 {sup o}C and 12 MPa (more than twice that of water cooled reactors), can serve over 85% of the world's non-transportation process heat demands and is ideally suited to serving Combined Heat and Electricity demands and industrial parks. Energy utilization of over 95% is feasible in process heat and Combined Heat and Electricity applications. The simple robust design of LEADIR-PS plants in

Safe transport of radioactive material. 3. ed

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-12-01

The IAEA has developed a standardized approach to transport safety training as a means of helping Member States to implement the Transport Regulations. The training manual is an anchor of this standardized approach to training: it contains all the topics presented in the sequential order recommended by the IAEA for the student to gain a thorough understanding of the body of knowledge that is needed to ensure that radioactive material ranked as Class 7 in the United Nations' nomenclature for dangerous goods - is transported safely. The explanations in the text refer, where needed, to the appropriate requirements in the IAEA's Transport Regulations; additional useful information is also provided. Thus, the training manual in addition to the Transport Regulations and their supporting documents is used by the IAEA as the basis for delivering all of its training courses on the safe transport of radioactive material. Enclosed with the training manual is a CD-ROM that contains the text of the manual as well as the visual aids that are used at the IAEA's training courses. The following topics are covered: review of radioactivity and radiation; review of radiation protection principles; regulatory terminology; basic safety concepts: materials and packages; activity limits and material restrictions; selection of optimal package type; test procedures: material and packages; requirements for transport; control of material in transport; fissile material: regulatory requirements and operational aspects; quality assurance; national competent authority; additional regulatory constraints for transport; international liability and insurance; emergency planning and preparedness; training; services provided by the IAEA.

Safe transport of radioactive material. 3. ed

International Nuclear Information System (INIS)

2002-01-01

The IAEA has developed a standardized approach to transport safety training as a means of helping Member States to implement the Transport Regulations. The training manual is an anchor of this standardized approach to training: it contains all the topics presented in the sequential order recommended by the IAEA for the student to gain a thorough understanding of the body of knowledge that is needed to ensure that radioactive material ranked as Class 7 in the United Nations' nomenclature for dangerous goods - is transported safely. The explanations in the text refer, where needed, to the appropriate requirements in the IAEA's Transport Regulations; additional useful information is also provided. Thus, the training manual in addition to the Transport Regulations and their supporting documents is used by the IAEA as the basis for delivering all of its training courses on the safe transport of radioactive material. Enclosed with the training manual is a CD-ROM that contains the text of the manual as well as the visual aids that are used at the IAEA's training courses. The following topics are covered: review of radioactivity and radiation; review of radiation protection principles; regulatory terminology; basic safety concepts: materials and packages; activity limits and material restrictions; selection of optimal package type; test procedures: material and packages; requirements for transport; control of material in transport; fissile material: regulatory requirements and operational aspects; quality assurance; national competent authority; additional regulatory constraints for transport; international liability and insurance; emergency planning and preparedness; training; services provided by the IAEA

Developing Safe Schools Partnerships with Law Enforcement

Science.gov (United States)

Rosiak, John

2009-01-01

Safe schools are the concern of communities throughout the world. If a school is safe, and if children feel safe, students "are better able to learn. But what are the steps to make" this happen? First, it is important to understand the problem: What are the threats to school safety? These include crime-related behaviors that find their way to…

SAFE USE OF DRUGS DURING PREGNANCY IN FOCUS OF INTERNATIONAL PRACTICE OF PHARMACOVIGILANCE SYSTEM AND TERATOLOGICAL INFORMATION SERVICE ORGANIZATION

Directory of Open Access Journals (Sweden)

K. A. Lutsevich

2012-01-01

Full Text Available The safe use of drugs during pregnancy is essential to optimize the health of both pregnant woman and her future child. At the same time obstetrician-gynecologists often face the lack of evidence-based information on the use of drugs and leave the issue to the woman herself — whether the treatment benefit to the mother outweighs risks to the unborn child — relying on the limited amount of scientific data. Preconception discussion of actual risks and safe treatment reduces patient fears and maximizes the emphasis on the therapy safety. At the same time, the lack of adequate information on safety for the majority of drugs used by pregnant women combined with the need to make appropriate treatment decisions and communicate drug risk information to a potentially vulnerable population is the most challenging and critical issue of pregnant women's health.

The medicines refrigerator and the importance of the cold chain in the safe storage of medicines.

Science.gov (United States)

Hatchett, Richard

2017-10-04

The medicines refrigerator is a common piece of equipment found in clinical areas. It is used to ensure specific medicines are safely stored within a narrow temperature range in line with manufacturers' instructions; this is usually between +2˚C and +8˚C, and ideally +5˚C. Drugs stored in the medicines refrigerator include: vaccines; insulin; chemotherapy drugs; topical preparations, such as some types of eye drops; and other treatments such as glucagon, which is used to manage severe hypoglycaemia. This article reviews the function of the medicines refrigerator and the checks required by healthcare practitioners to ensure that medicines remain safely stored and their effectiveness is maintained. It also outlines the medicines refrigeration procedure known as the 'cold chain', which includes the use of cold boxes or vaccine carriers to maintain the required temperature of medicines during transport from the manufacturer to user, or between healthcare departments. ©2012 RCN Publishing Company Ltd. All rights reserved. Not to be copied, transmitted or recorded in any way, in whole or part, without prior permission of the publishers.

Development of a National System to Regulate Safe Transport of Radioactive Materials in Ukraine

International Nuclear Information System (INIS)

Gashev, M.; Kutuzova, T.; Sakalo, V.

2016-01-01

The paper provides brief information on development of the legislative framework and regulatory requirements in transport of radioactive materials in Ukraine. The application of IAEA documents is demonstrated and their contribution to the improvement of the national regulatory control system and processes of its harmonization with international safety requirements is underlined. Proposals for coordination and interaction enhancement in order to improve safety in safe transport of radioactive materials are defined in the conclusion. (author)

Solid-solid phase transformation via internal stress-induced virtual melting, significantly below the melting temperature. Application to HMX energetic crystal.

Science.gov (United States)

Levitas, Valery I; Henson, Bryan F; Smilowitz, Laura B; Asay, Blaine W

2006-05-25

We theoretically predict a new phenomenon, namely, that a solid-solid phase transformation (PT) with a large transformation strain can occur via internal stress-induced virtual melting along the interface at temperatures significantly (more than 100 K) below the melting temperature. We show that the energy of elastic stresses, induced by transformation strain, increases the driving force for melting and reduces the melting temperature. Immediately after melting, stresses relax and the unstable melt solidifies. Fast solidification in a thin layer leads to nanoscale cracking which does not affect the thermodynamics or kinetics of the solid-solid transformation. Thus, virtual melting represents a new mechanism of solid-solid PT, stress relaxation, and loss of coherence at a moving solid-solid interface. It also removes the athermal interface friction and deletes the thermomechanical memory of preceding cycles of the direct-reverse transformation. It is also found that nonhydrostatic compressive internal stresses promote melting in contrast to hydrostatic pressure. Sixteen theoretical predictions are in qualitative and quantitative agreement with experiments conducted on the PTs in the energetic crystal HMX. In particular, (a) the energy of internal stresses is sufficient to reduce the melting temperature from 551 to 430 K for the delta phase during the beta --> delta PT and from 520 to 400 K for the beta phase during the delta --> beta PT; (b) predicted activation energies for direct and reverse PTs coincide with corresponding melting energies of the beta and delta phases and with the experimental values; (c) the temperature dependence of the rate constant is determined by the heat of fusion, for both direct and reverse PTs; results b and c are obtained both for overall kinetics and for interface propagation; (d) considerable nanocracking, homogeneously distributed in the transformed material, accompanies the PT, as predicted by theory; (e) the nanocracking does not

Internal friction and microplasticity of ice Isub(h)

International Nuclear Information System (INIS)

Perez, J.; Mai, C.; Tatibouet, J.; Vassoille, R.

1976-01-01

This study is concerned with internal-friction measurements made at low frequency (torsion pendulum) on specimens of ice Isub(h). In the case of a single crystal, the spectrum of internal friction vs. temperature exhibits the classical relaxation peak. This peak is followed by an increase of damping above 260 K. Furthermore, in this temperature range, the internal friction delta is shown to be amplitude dependent: delta increases with shear strain γ as long as the temperature T is high. These features are strongly modified by plastic deformation of ice in particular i) high-temperature internal friction is increased as long as the plastic defomation ratio is important, ii) high-temperature internal friction becomes more amplitude dependent. In the high-temperature range the mobility of dislocations in ice increase quickly. During the internal-friction measurements the cyclic stress causes movement of linear defects and, hence, damping phenomena. Then, the theoretical analysis of the dynamic behaviour of dislocations in ice has been used to interpret the preceding results. This interpretation allows us to connect our damping data with the microplastic behaviour of ice

Creep behavior under internal pressure of zirconium alloy cladding oxidized in steam at high temperature

International Nuclear Information System (INIS)

Chosson, Raphael

2014-01-01

During hypothetical Loss-Of-Coolant-Accident (LOCA) scenarios, zirconium alloy fuel cladding tubes creep under internal pressure and are oxidized on their outer surface at high temperature (HT). Claddings become stratified materials: zirconia and oxygen-stabilized α phase, called α(O), are formed on the outer surface of the cladding whereas the inner part remains in the β domain. The strengthening effect of oxidation on the cladding creep behavior under internal pressure has been highlighted at HT. In order to model this effect, the creep behavior of each layer had to be determined. This study focused on the characterization of the creep behavior of the α(O) phase at HT, through axial creep tests performed under vacuum on model materials, containing from 2 to 7 wt.% of oxygen and representative of the α(O) phase. For the first time, two creep flow regimes have been observed in this phase. Underlying physical mechanisms and relevant microstructural parameters have been discussed for each regime. The strengthening effect due to oxygen on the α(O) phase creep behavior at HT has been quantified and creep flow equations have been identified. A ductile to brittle transition criterion has been also suggested as a function of temperature and oxygen content. Relevance of the creep flow equations for each layer, identified in this study or from the literature, has been discussed. Then, a finite element model, describing the oxidized cladding as a stratified material, has been built. Based on this model, a fraction of the experimental strengthening during creep is predicted. (author) [fr

[Sciatic nerve block "out-of-plane" distal to the bifurcation: effective and safe].

Science.gov (United States)

Geiser, T; Apel, J; Vicent, O; Büttner, J

2017-03-01

Ultrasound guided distal sciatic nerve block (DSB) at bifurcation level shows fast onset and provides excellent success rates. However, its safe performance might be difficult for the unexperienced physician. Just slightly distal to the bifurcation, the tibial nerve (TN) and common fibular nerve (CFN) can be shown clearly separated from each other. Therefore, we investigated if a block done here would provide similar quality results compared to the DSB proximally to the division, with a potentially lower risk of nerve damage. In this randomized, prospective trial, 56 patients per group received either a DSB distal to the bifurcation "out-of-plane" (dist.) or proximally "in-plane" (prox.) with 30 ml of Mepivacaine 1% each. Success was tested by a blinded examiner after 15 and 30 min respectively (sensory and motor block of TN and CFN: 0 = none, 2 = complete, change of skin temperature). Videos of the blocks were inspected by an independent expert retrospectively with regard to the spread of the local anesthetic (LA) and accidental intraneural injection. Cumulative single nerve measurements and temperature changes revealed significant shorter onset and better efficacy (dist/prox: 15 min: 3.13 ± 1.86/1.82 ± 1.62; 30 min: 5.73 ± 1.92/3.21 ± 1.88; T 15 min : 30.3 ± 3.48/28.0 ± 3.67, T 30 min . 33.0 ± 2.46/30.6 ± 3.86; MV/SD; ANOVA; p safe application of the LA, so an effective block can be done with just one injection. DSB slightly distal to the bifurcation, in an out-of-plane technique between the TN and CFN, can be done fast, effectively and safe.

Summary of advanced LMR [Liquid Metal Reactor] evaluations: PRISM [Power Reactor Inherently Safe Module] and SAFR [Sodium Advanced Fast Reactor

International Nuclear Information System (INIS)

Van Tuyle, G.J.; Slovik, G.C.; Chan, B.C.; Kennett, R.J.; Cheng, H.S.; Kroeger, P.G.

1989-10-01

In support of the US Nuclear Regulatory Commission (NRC), Brookhaven National Laboratory (BNL) has performed independent analyses of two advanced Liquid Metal Reactor (LMR) concepts. The designs, sponsored by the US Department of Energy (DOE), the Power Reactor Inherently Safe Module (PRISM) [Berglund, 1987] and the Sodium Advanced Fast Reactor (SAFR) [Baumeister, 1987], were developed primarily by General Electric (GE) and Rockwell International (RI), respectively. Technical support was provided to DOE, RI, and GE, by the Argonne National Laboratory (ANL), particularly with respect to the characteristics of the metal fuels. There are several examples in both PRISM and SAFR where inherent or passive systems provide for a safe response to off-normal conditions. This is in contrast to the engineered safety systems utilized on current US Light Water Reactor (LWR) designs. One important design inherency in the LMRs is the ''inherent shutdown'', which refers to the tendency of the reactor to transition to a much lower power level whenever temperatures rise significantly. This type of behavior was demonstrated in a series of unscrammed tests at EBR-II [NED, 1986]. The second key design feature is the passive air cooling of the vessel to remove decay heat. These systems, designated RVACS in PRISM and RACS in SAFR, always operate and are believed to be able to prevent core damage in the event that no other means of heat removal is available. 27 refs., 78 figs., 3 tabs

Towards Safe Robotic Surgical Systems

DEFF Research Database (Denmark)

Sloth, Christoffer; Wisniewski, Rafael

2015-01-01

a controller for motion compensation in beating-heart surgery, and prove that it is safe, i.e., the surgical tool is kept within an allowable distance and orientation of the heart. We solve the problem by simultaneously finding a control law and a barrier function. The motion compensation system is simulated...... from several initial conditions to demonstrate that the designed control system is safe for every admissible initial condition....

Safe use of ionizing radiations

Energy Technology Data Exchange (ETDEWEB)

1973-01-01

Based on the ''Code of Practice for the protection of persons against ionizing radiations arising from medical and dental use'' (CIS 74-423), this handbook shows how hospital staff can avoid exposing themselves and others to these hazards. It is designed particularly for junior and student nurses. Contents: ionizing radiations, their types and characteristics; their uses and dangers; basic principles in their safe use; safe use in practice; explanation of terms.

Staying Safe in the Water

Centers for Disease Control (CDC) Podcasts

2008-05-15

In this podcast, Dr. Julie Gilchrist, a pediatrician and medical epidemiologist from CDC’s Injury Center, talks about staying safe in the water. Tips are for all audiences, with a focus on preventing drownings and keeping children safe in and around the pool, lake, or ocean.  Created: 5/15/2008 by National Center for Injury Prevention and Control (NCIPC).   Date Released: 5/19/2008.

[Towards safe motherhood. World Health Day].

Science.gov (United States)

Plata, M I

1998-06-01

The objective of the 'safe motherhood' initiative is to reduce maternal mortality by 50% by the year 2000. A strong policy is needed to permit development of national and international programs. The lifetime risk of death from causes related to complications of pregnancy is estimated at 1/16 in Africa, 1/65 in Asia, 1/130 in Latin America and the Caribbean, 1/1400 in Europe, and 1/3700 in North America. A minimum of 585,000 women die of maternal causes each year, with nearly 90% of the deaths occurring in Asia and Africa. Approximately 50 million women suffer from illnesses related to childbearing. A principal cause of maternal mortality is lack of medical care during labor, delivery, and the postpartum period. Motherhood will become safe if governments, multilateral and bilateral funding agencies, and nongovernmental organizations give it the high priority it requires. Women also die because they lack rights. Their reduced decision-making power and inequitable access to family and social resources prevents them from overcoming barriers to health care. Women die when they begin childbearing at a very young age, yet an estimated 11% of births throughout the world each year are to adolescents. Adolescents have very limited access to family planning, either through legal restrictions or obstacles created by family planning workers. Maternal deaths would be avoided if all births were attended by trained health workers; an estimated 60 million births annually are not. Prevention of unwanted pregnancy and, thus, of the 50 million abortions estimated to take place each year would avoid over 200 maternal deaths each day. Unsafe abortions account for 13% of maternal deaths. The evidence demonstrates that rates of unsafe abortion and abortion mortality are higher where laws are more restrictive.

Internal state variable plasticity-damage modeling of AISI 4140 steel including microstructure-property relations: temperature and strain rate effects

Science.gov (United States)

Nacif el Alaoui, Reda

Mechanical structure-property relations have been quantified for AISI 4140 steel. under different strain rates and temperatures. The structure-property relations were used. to calibrate a microstructure-based internal state variable plasticity-damage model for. monotonic tension, compression and torsion plasticity, as well as damage evolution. Strong stress state and temperature dependences were observed for the AISI 4140 steel. Tension tests on three different notched Bridgman specimens were undertaken to study. the damage-triaxiality dependence for model validation purposes. Fracture surface. analysis was performed using Scanning Electron Microscopy (SEM) to quantify the void. nucleation and void sizes in the different specimens. The stress-strain behavior exhibited. a fairly large applied stress state (tension, compression dependence, and torsion), a. moderate temperature dependence, and a relatively small strain rate dependence.

Implementation of the 1996 edition of the IAEA regulations for the safe transport of radioactive material

International Nuclear Information System (INIS)

Rawl, R.R.; Kervella, O.

1998-01-01

The International Atomic Energy Agency (IAEA) completed a 10 year and revision of its 'Regulations for the Safe Transport of Radioactive Material' with approval of the amendments by its Board of Governors in September 1996. The revised edition contains some important changes in the regulations, including: type C package requirements; provisions for low dispersible material; uranium hexafluoride packaging; exemption value specifications; operational requirements, including the creation of a criticality safety index and new proper shipping names/UN numbers. The 1996 edition of the IAEA regulations has been published and corresponding revisions now being considered by the international transport safety organizations and Member States. In particular, the United Nations Committee of Experts on the Transport of Dangerous Goods, International Civil Aviation Organization and International Maritime Organization and preparing revisions to take into account the revised Class 7 requirements. An effective date of 1 January 2001 has been recommended so that international and domestic requirements might come into force simultaneously, thereby avoiding disruptive out-of-phase implementation. (authors)

CREST-SAFE: Snow LST validation, wetness profiler creation, and depth/SWE product development

Science.gov (United States)

Perez Diaz, C. L.; Lakhankar, T.; Romanov, P.; Khanbilvardi, R.; Munoz Barreto, J.; Yu, Y.

2017-12-01

CREST-SAFE: Snow LST validation, wetness profiler creation, and depth/SWE product development The Field Snow Research Station (also referred to as Snow Analysis and Field Experiment, SAFE) is operated by the NOAA Center for Earth System Sciences and Remote Sensing Technologies (CREST) in the City University of New York (CUNY). The field station is located within the premises of the Caribou Municipal Airport (46°52'59'' N, 68°01'07'' W) and in close proximity to the National Weather Service (NWS) Regional Forecast Office. The station was established in 2010 to support studies in snow physics and snow remote sensing. The Visible Infrared Imager Radiometer Suite (VIIRS) Land Surface Temperature (LST) Environmental Data Record (EDR) and Moderate Resolution Imaging Spectroradiometer (MODIS) LST product (provided by the Terra and Aqua Earth Observing System satellites) were validated using in situ LST (T-skin) and near-surface air temperature (T-air) observations recorded at CREST-SAFE for the winters of 2013 and 2014. Results indicate that T-air correlates better than T-skin with VIIRS LST data and that the accuracy of nighttime LST retrievals is considerably better than that of daytime. Several trends in the MODIS LST data were observed, including the underestimation of daytime values and night-time values. Results indicate that, although all the data sets showed high correlation with ground measurements, day values yielded slightly higher accuracy ( 1°C). Additionally, we created a liquid water content (LWC)-profiling instrument using time-domain reflectometry (TDR) at CREST-SAFE and tested it during the snow melt period (February-April) immediately after installation in 2014. Results displayed high agreement when compared to LWC estimates obtained using empirical formulas developed in previous studies, and minor improvement over wet snow LWC estimates. Lastly, to improve on global snow cover mapping, a snow product capable of estimating snow depth and snow water

Safe operating envelope

Energy Technology Data Exchange (ETDEWEB)

Oliva, N [Ontario Hydro, Toronto, ON (Canada)

1997-12-01

Safe Operating Envelope is described representing: The outer bound of plant conditions within which day-to-day plant operation must be maintained in order to comply with regulatory requirements, associated safety design criteria and corporate nuclear safety goals. Figs.

Safe operating envelope

International Nuclear Information System (INIS)

Oliva, N.

1997-01-01

Safe Operating Envelope is described representing: The outer bound of plant conditions within which day-to-day plant operation must be maintained in order to comply with regulatory requirements, associated safety design criteria and corporate nuclear safety goals. Figs

An Automated Safe-to-Mate (ASTM) Tester

Science.gov (United States)

Nguyen, Phuc; Scott, Michelle; Leung, Alan; Lin, Michael; Johnson, Thomas

2013-01-01

Safe-to-mate testing is a common hardware safety practice where impedance measurements are made on unpowered hardware to verify isolation, continuity, or impedance between pins of an interface connector. A computer-based instrumentation solution has been developed to resolve issues. The ASTM is connected to the circuit under test, and can then quickly, safely, and reliably safe-to-mate the entire connector, or even multiple connectors, at the same time.

Safe management of waste from health-care activities

International Nuclear Information System (INIS)

Pruess, A.; Giroult, E.; Rushbrook, P.

1999-01-01

The waste produced in the course of health-care activities, from contaminated needles to radioactive isotopes, carries a greater potential for causing infection and injury than any other type of waste, and inadequate or inappropriate management is likely to have serious public health consequences and deleterious effects on the environment. This handbook - the result of extensive international consultation and collaboration - provides comprehensive guidance on safe, efficient, and environmentally sound methods for the handling and disposal of health-care wastes. The various categories of waste are clearly defined and the particular hazards that each poses are described. Considerable prominence is given to the careful planning that is essential for the success of waste management; workable means of minimizing waste production are outlined and the role of reuse and recycling of waste is discussed. Most of the text, however, is devoted to the collection, segregation, storage, transport, and disposal of wastes. Details of containers for each category of waste, labelling of waste packages, and storage conditions are provided, and the various technologies for treatment of waste and disposal of final residues are discussed at length. Advice is given on occupational safety for all personnel involved with waste handling, and a separate chapter is devoted to the closely related topic of hospital hygiene and infection control. The handbook pays particular attention to basic processes and technologies that are not only safe but also affordable, sustainable, and culturally appropriate. For health-care settings in which resources are severely limited there is a separate chapter on minimal programmes; this summarizes all the simplest and least costly techniques that can be employed for the safe management of health-care wastes. The guide is aimed at public health managers and policy-makers, hospital managers, environmental health professionals, and all administrators with an

REPORT FROM THE ORGANIZERS: The 25th International Conference on Low Temperature Physics

Science.gov (United States)

Kes, Peter

2009-03-01

The 25th International Conference on Low Temperature Physics (LT25) was hosted by the Kamerlingh Onnes Laboratorium of the Leiden Institute of Physics and held in the RAI Convention Center in Amsterdam, The Netherlands, 6-13 August 2008. It was the second time that the Kamerlingh Onnes Laboratory had the privilege of organizing an LT conference. In 1958, at LT6, 50 years of liquid helium temperatures were commemorated; in 2008 we celebrated the 100th anniversary of the remarkable achievements of Heike Kamerlingh Onnes and his collaborators in Leiden. In 1958 there were 323 participants and 145 papers appeared in the proceedings; in 2008 these numbers had increased to 1390 participants and 900 papers, of which eventually 849 were accepted. This large participation required adequate conference and housing facilities. These could not be found in Leiden, but were conveniently available in Amsterdam. The triennial International Low Temperature Conferences are organized under the auspices of the International Union of Pure and Applied Physics (IUPAP) through Commission C5 on Low Temperature Physics. It is the most important global meeting that brings together the international scientific community in the broad field of Low Temperature Physics. Because the meeting is held only every third year the 11 plenary and 22 half plenary talks (of 45 or 30 min.) generally provide an overview of important new discoveries over the last few years, whereas the 161 short oral presentations (20 min.) are mainly focused on very recent developments. Since the field is broad, embracing a large section of condensed matter physics, the program is divided into five parallel program lines: A. Quantum Gases, Fluids and Solids B. Superconductivity C. Quantum Phase Transitions and Magnetism D. Electronic Quantum Transport in Condensed Matter E. Cryogenic Techniques and Applications This distinction was used both to group the 1625 accepted abstracts, and the short-oral and poster presentations; the

Internal friction of Fe-B alloys neutron irradiated at low temperature

International Nuclear Information System (INIS)

Kitajima, Kazunori; Futagami, Koji; Abe, Hironobu; Yoshida, Hiroyuki.

1975-01-01

Measurements were made on the internal friction of Fe-B alloys irradiated by neutron at 16 0 K to the dose of 3x10 16 nvt (>1 MeV) and 6x10 17 nvt (thermal). Boron was used to enhance the production of defects by the nuclear transformation B 10 (n,α)Li 7 . Relaxation peaks were found in specimens containing dispersed fine precipitates of NbB 2 in range of B 500--7200 wt ppm and Nb 2000--30000 wt ppm. The most prominent peak is the one with the peak temperature of 169 0 K at the frequency of 264 c/sec. Activation energy determined from the peak shift is 0.28+-0.01 eV, which is nearly equal to that of migration of self-interstitial reported on pure iron. However activation energy of the decay of peaks by annealing is about 0.7 eV. Interpretation was presented that the peak may be attributed to re-orientation of self-interstitials loosely bound to a boron atom. (auth.)

USING THE SAFE SYSTEM APPROACH TO KEEP OLDER DRIVERS SAFELY MOBILE

Directory of Open Access Journals (Sweden)

Jim LANGFORD

2006-01-01

Full Text Available In 2003, Australian road transport jurisdictions collectively accepted that the greatest road safety gains would be achieved through adopting a Safe System approach, derived from Sweden's Vision Zero and the Netherlands' Sustainable Safety strategies. A key objective of all three approaches is to manage vehicles, the road infrastructure, speeds, road users and the interactions between these components, to ensure that in the event of crashes, crash energies will remain at levels that minimize the probability of death and serious injury. Older drivers pose a particular challenge to the Safe System approach, given particularly their greater physical frailty, their driving patterns and for some at least, their reduced fitness to drive. This paper has analyzed the so-called ‘older driver problem’ and identified a number of key factors underpinning their crash levels, for which countermeasures can be identified and implemented within a Safe System framework. The recommended countermeasures consist of: (1 safer roads, through a series of design improvements particularly governing urban intersections; (2 safer vehicles, through both the promotion of crashworthiness as a critical consideration when purchasing a vehicle and the wide use of developed and developing ITS technologies; (3 safer speeds especially at intersections; and (4 safer road users, through both improved assessment procedures to identify the minority of older drivers with reduced fitness to drive and educational efforts to encourage safer driving habits particularly but not only through self-regulation.

Training in radiation protection and the safe use of radiation sources

International Nuclear Information System (INIS)

2001-01-01

The need for education and training in the various disciplines of radiation protection has long been recognized by the IAEA, the International Labour Organization (ILO), the United Nations Educational, Scientific and Cultural Organization, the World Health Organization and the Pan American Health Organization (PAHO). This need has been partially met through the many training courses undertaken by these organizations, either individually or in collaboration. The IAEA has assisted developing Member States in the training of specialists in radiation protection and safety through its organized educational and specialized training courses, workshops, seminars, fellowships and scientific visits. Training is an important means of promoting safety culture and enhancing the level of competence of personnel involved in radiation protection activities, and has acquired a place in the IAEA's programme accordingly. For example, the IAEA Post-graduate Educational Course in Radiation Protection and the Safe Use of Radiation Sources is regularly offered in countries around the world, and has been provided in Arabic, English, French, Spanish and Russian. The training provided by the IAEA is primarily aimed at regulators, professionals working in radiation protection and those responsible for the development of training programmes in their own countries. The importance of adequate and appropriate training for all those working with ionizing radiation has been highlighted by the results of the IAEA's investigations of radiological accidents. A significant contributory factor in a number of the accidents has been a lack of adequate training, which gave rise to errors with serious consequences. This report provides assistance in organizing training and complying with the requirements on training of the International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources (BSS). The previous version of this report. Technical Reports

Evolution of Near-Surface Internal and External Oxide Morphology During High-Temperature Selective Oxidation of Steels

Science.gov (United States)

Story, Mary E.; Webler, Bryan A.

2018-05-01

In this work we examine some observations made using high-temperature confocal scanning laser microscopy (HT-CSLM) during selective oxidation experiments. A plain carbon steel and advanced high-strength steel (AHSS) were selectively oxidized at high temperature (850-900°C) in either low oxygen or water vapor atmospheres. Surface evolution, including thermal grooving along grain boundaries and oxide growth, was viewed in situ during heating. Experiments investigated the influence of the microstructure and oxidizing atmosphere on selective oxidation behavior. Sequences of CSLM still frames collected during the experiment were processed with ImageJ to obtain histograms that showed a general darkening trend indicative of oxidation over time with all samples. Additional ex situ scanning electron microscopy and energy dispersive spectroscopy analysis supported in situ observations. Distinct oxidation behavior was observed for each case. Segregation, grain orientation, and extent of internal oxidation were all found to strongly influence surface evolution.

Feeling safe during an inpatient hospitalization: a concept analysis.

Science.gov (United States)

Mollon, Deene

2014-08-01

This paper aims to explore the critical attributes of the concept feeling safe. The safe delivery of care is a high priority; however; it is not really known what it means to the patient to 'feel safe' during an inpatient hospitalization. This analysis explores the topic of safety from the patient's perspective. Concept analysis. The data bases of CINAHL, Medline, PsychInfo and Google Scholar for the years 1995-2012 were searched using the terms safe and feeling safe. The eight-step concept analysis method of Walker and Avant was used to analyse the concept of feeling safe. Uses and defining attributes, as well as identified antecedents, consequences and empirical referents, are presented. Case examples are provided to assist in the understanding of defining attributes. Feeling safe is defined as an emotional state where perceptions of care contribute to a sense of security and freedom from harm. Four attributes were identified: trust, cared for, presence and knowledge. Relationship, environment and suffering are the antecedents of feeling safe, while control, hope and relaxed or calm are the consequences. Empirical referents and early development of a theory of feeling safe are explored. This analysis begins the work of synthesizing qualitative research already completed around the concept of feeling safe by defining the key attributes of the concept. Support for the importance of developing patient-centred models of care and creating positive environments where patients receive high-quality care and feel safe is provided. © 2014 John Wiley & Sons Ltd.

Experimental optimization of temperature distribution in the hot-gas duct through the installation of internals in the hot-gas plenum of a high-temperature reactor

International Nuclear Information System (INIS)

Henssen, J.; Mauersberger, R.

1990-01-01

The flow conditions in the hot-gas plenum and in the adjacent hot-gas ducts and hot-gas pipes for the high-temperature reactor project PNP-1000 (nuclear process heat project for 1000 MW thermal output) have been examined experimentally. The experiments were performed in a closed loop in which the flow model to be analyzed, representing a 60deg sector of the core bottom of the PNP-1000 with connecting hot-gas piping and diverting arrangements, was installed. The model scale was approx. 1:5.6. The temperature and flow velocity distribution in the hot-gas duct was registered by means of 14 dual hot-wire flowmeters. Through structural changes and/or the installation of internals into the hot-gas plenum of the core bottom offering little flow resistance coolant gas temperature differentials produced in the core could be reduced to such an extent that a degree of mixture amounting to over 80% was achieved at the entrance of the connected heat exchanger systems. Thereby the desired goal of an adequate degree of mixture of the hot gas involving an acceptable pressure loss was reached. (orig.)

Materials for passively safe reactors

International Nuclear Information System (INIS)

Simnad, T.

1993-01-01

Future nuclear power capacity will be based on reactor designs that include passive safety features if recent progress in advanced nuclear power developments is realized. There is a high potential for nuclear systems that are smaller and easier to operate than the current generation of reactors, especially when passive or intrinsic characteristics are applied to provide inherent stability of the chain reaction and to minimize the burden on equipment and operating personnel. Taylor, has listed the following common generic technical features as the most important goals for the principal reactor development systems: passive stability, simplification, ruggedness, case of operation, and modularity. Economic competitiveness also depends on standardization and assurance of licensing. The performance of passively safe reactors will be greatly influenced by the successful development of advanced fuels and materials that will provide lower fuel-cycle costs. A dozen new designs of advanced power reactors have been described recently, covering a wide spectrum of reactor types, including pressurized water reactors, boiling water reactors, heavy-water reactors, modular high-temperature gas-cooled reactors (MHTGRs), and fast breeder reactors. These new designs address the need for passive safety features as well as the requirement of economic competitiveness

Creating Safe Spaces for Music Learning

Science.gov (United States)

Hendricks, Karin S.; Smith, Tawnya D.; Stanuch, Jennifer

2014-01-01

This article offers a practical model for fostering emotionally safe learning environments that instill in music students a positive sense of self-belief, freedom, and purpose. The authors examine the implications for music educators of creating effective learning environments and present recommendations for creating a safe space for learning,…

Keeping Food Safe

Centers for Disease Control (CDC) Podcasts

2009-05-27

This CDC Kidtastics podcast discusses things kids and parents can do to help prevent illness by keeping food safe.  Created: 5/27/2009 by National Center for Zoonotic, Vector-Borne, and Enteric Diseases (NCZVED).   Date Released: 5/27/2009.

Calculation of the fuel temperature coefficient of reactivity considering non-uniform radial temperature distribution in the fuel rod

Energy Technology Data Exchange (ETDEWEB)

Pazirandeh, Ali [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Science and Research Branch; Hooshyar Mobaraki, Almas

2017-07-15

The safe operation of a reactor is based on feedback models. In this paper we attempted to discuss the influence of a non-uniform radial temperature distribution on the fuel rod temperature coefficient of reactivity. The paper demonstrates that the neutron properties of a reactor core is based on effective temperature of the fuel to obtain the correct fuel temperature feedback. The value of volume-averaged temperature being used in the calculations of neutron physics with feedbacks would result in underestimating the probable event. In the calculation it is necessary to use the effective temperature of the fuel in order to provide correct accounting of the fuel temperature feedback. Fuel temperature changes in different zones of the core and consequently reactivity coefficient change are an important parameter for analysis of transient conditions. The restricting factor that compensates the inserted reactivity is the temperature reactivity coefficient and effective delayed neutron fraction.

Cold-fusion as safe and hazardless energy-source of the 21st century

International Nuclear Information System (INIS)

Gupta, R.C.; Gupta, Sushant

2012-01-01

Out of the two processes for nuclear-energy; nuclear-fission is plagued with problem of nuclear-radiation hazard, whereas though nuclear-fusion is safe but almost impossible to be done on earth specially at room- temperature. In 1989, two scientists Fleischmann and Pons in USA proposed a table-top, room temperature electrolysis-experiment of heavy-water with palladium-electrode; this is commonly called cold-fusion wherein nuclear-fusion is said to be taking place. This created a big storm and controversy in the scientific community. Initially the cold-fusion was heavily criticized and several objections (such as: non-reproducibility, non-observation of telltale signature of nuclear-reaction) were raised. The research-work of McKubre and others have clarified the objections and have established that for cold-fusion to take place certain threshold conditions (such as purity of electrode, current-density, deuterium to palladium loading ratio) needs to be satisfied. In due course of time, the Truth prevailed and the cold-fusion got more and more support by many scientists in several countries including India (BARC historic role has been appreciated worldwide). Biggest objection, however, was lack of a proper theory for how Coulomb-repulsion is overcome in cold-fusion. A possible explanation for how the Coulomb-repulsion is overcome, is given in this paper; which is based on a new-found Gupta-Dinu effect, which is a natural outcome of special-relativity via modification in Lorentz force formula. The recent nuclear-accidents have raised international-opinion against nuclear-fission, whereas sin-like hot-fusion on earth is not possible. Now it seems that ultimately it is the cold-fusion which will provide hazardless neat and cheap energy for the 21 st century and India could play a leading role in this direction. (author)

Evaluation of internal boiler components and gases using a high-temperature infrared (IR) lens

Science.gov (United States)

Hammaker, Robert G.; Colsher, Richard J.; Miles, Jonathan J.; Madding, Robert P.

1996-03-01

Fuel accounts for an average of seventy percent of the yearly operational and maintenance costs of all the fossil stations in the United States. This amounts to 30 billion dollars spent for fuel each year. In addition, federal and state environmental codes have been enforcing stricter regulations that demand cleaner environments, such as the reduction of nitrogen oxides (NOx), which are a by-product of the fossil fuel flame. If the burn of the flame inside a boiler could be optimized, the usage of fuel and the amounts of pollution produced would be significantly reduced, and many of the common boiler tube failures can be avoided. This would result in a major dollar savings to the utility industry, and would provide a cleaner environment. Accomplishing these goals will require a major effort from the designers and operators that manufacture, operate, and maintain the fossil stations. Over the past few years re-designed burners have been installed in many boilers to help control the temperatures and shape of the flame for better performance and NOx reduction. However, the measurement of the processes and components inside the furnace, that could assist in determining the desired conditions, can at times be very difficult due to the hostile hot environment. In an attempt to resolve these problems, the EPRI M&D Center and a core group of EPRI member utilities have undertaken a two-year project with various optical manufacturers, IR manufacturers, and IR specialists, to fully develop an optical lens that will withstand the high furnace temperatures. The purpose of the lens is to explore the possibilities of making accurate high temperature measurements of the furnace processes and components in an ever-changing harsh environment. This paper provides an introduction to EPRI's internal boiler investigation using an IR high temperature lens (HTL). The paper describes the objectives, approach, benefits, and project progress.

Analysis of application of different approaches to secure safe drinking water

Directory of Open Access Journals (Sweden)

Pendić Zoran

2017-01-01

Full Text Available In this analysis, the risk systems include the systems within which services sensitive to risk are executed. The complex service of population supply with safe drinking water is considered to be risky. Guidelines for drinking water quality of the World Health Organization (WHO recommends the use of effective preventive approaches to risk-based management of the safety and quality of drinking water. For example, Food Safety Law of the Republic of Serbia stipulates mandatory application of HACCP system in order to obtain safe drinking water. Different approaches to preventive risk-based management for the sake of the safety and quality of drinking water are applied nowadays. In this paper we consider the following approaches: Original Codex Alimentarius HACCP system and some of its modified versions; International standard ISO 22000: 2005 Food safety management systems - Requirements for any organization in the food chain; Water Safety Plan (WSP of the World Health Organization (WHO; Generalized HACCP system. All of these approaches are based, to a greater or lesser extent, on the original Codex Alimentarius HACCP system. The paper gives a situation analysis (SWOT analysis of considered approaches.

Quicker yet safe: skeletonization of 1640 internal mammary arteries with harmonic technology in 965 patients.

Science.gov (United States)

Kieser, Teresa M; Rose, M Sarah; Aluthman, Uthman; Narine, Kishan

2014-05-01

Skeletonization of the internal mammary artery (IMA) facilitates arterial grafting and has been shown to reduce deep sternal infection but is more time-consuming and tedious than pedicle harvest. We wished to determine if use of harmonic technology (HT) facilitates skeletonization of the IMA and is as safe as the conventional technique of skeletonization. In a consecutive series of 1057 patients with isolated coronary artery bypass graft (CABG) surgery from 2003 to 2013, adverse events and recorded harvest times were compared between harmonic (965 patients) and non-harmonic patients (86 patients). HT was used to harvest 1640 IMAs in 965 (91%) of 1057 consecutive CABG patients and skeletonization with the traditional technique (use of an electrocautery tip as a dissector) was used to harvest 147 IMAs in 86 patients. Six patients had no IMA harvested with this surgery (4 patients had an IMA used from a previous CABG, 1 had no disease of the left anterior descending coronary artery and 1 patient was in cardiogenic shock precluding IMA use). Excluding patients with single-vessel disease, 730/987 (74%) of patients received bilateral IMAs. Demographics of patients with and without harmonic skeletonization, respectively, were the following: mean age: 64.7 vs 67.7 years; diabetes: 33 vs 34%; women: 21 vs 26% and median European System for Cardiac Operative Risk Evaluation: 2.9 vs 3.2. The mean harvest time for 77 non-harmonic skeletonized mammary arteries (49 surgeries) was 32.2 min (95% confidence interval (CI): 30.1, 34.3), for harmonic skeletonized arteries after 450 surgeries was 28.4 min, (95% CI: 27.8, 29.1) and in the last 100 IMAs harvested for the isolated harmonic device use/mammary was 15.4 min (95% CI: 14.0, 16.7). Major adverse events for patients with and without harmonic skeletonization, respectively, were: reoperation for bleeding: 2.7 vs 3.5% (difference = 0.8%, 95% CI: -3.2, 4.8); damaged mammaries: 0.4 vs 0.7% (difference = 0.3%, 95% CI: -1.0, 1.7); deep

Safe injection practice among health care workers, Gharbiya, Egypt.

Science.gov (United States)

Ismail, Nanees A; Aboul Ftouh, Aisha M; El Shoubary, Waleed H

2005-01-01

A cross-sectional study was conducted in 25 health care facilities in Gharbiya governorate to assess safe injection practices among health care workers (HCWs). Two questionnaires, one to collect information about administrative issues related to safe injection and the other to collect data about giving injections, exposure to needle stick injuries, hepatitis B vaccination status and safe injection training. Practices of injections were observed using a standardized checklist. The study revealed that there was lack of both national and local infection control policies and lack of most of the supplies needed for safe injection practices. Many safe practices were infrequent as proper needle manipulation before disposal (41%), safe needle disposal (47.5%), reuse of used syringe & needle (13.2%) and safe syringe disposal (0%). Exposure to needle stick injuries were common among the interviewed HCWs (66.2%) and hand washing was the common post exposure prophylaxis measure (63.4%). Only 11.3% of HCWs had full course hepatitis B vaccination. Infection control -including safe injections- training programs should be afforded to all HCWs.

Regulations for the Safe Transport of Radioactive Materials. 1964 Revised Edition

International Nuclear Information System (INIS)

1965-01-01

In 1961 the International Atomic Energy Agency, within the framework of its statutory functions and in accordance with recommendations made by its Preparatory Commission and by the Economic and Social Council of the United Nations, published safety regulations which could be applied to the national and international transport of radio active materials by all means of transport. At the same time, the Director General of the Agency indicated that these regulations would be revised at appropriate intervals in consultation with Member States and the organizations concerned and invited suggestions for their improvement in the light of experience and increased knowledge. In preparing the revised regulations presented in this document, the Agency has received considerable support from its Member States and the organizations concerned, which have made extensive studies and suggestions in order to assist in its work. The Agency also convened several meetings of experts from its Member States and of representatives of a number of international organizations, and has been represented in several meetings convened by those organizations. In publishing the revised transport regulations which result from that co-ordinated effort, the Agency aims at proposing a lasting framework of principles and rules, complemented by appropriate technical data, acceptable for the safe transport of radio active materials by air, land and water. In particular, the developments which have been introduced concerning the packaging requirements, the nuclear safety criteria for the transport of fissile materials and the methods for testing packages should facilitate the international acceptance of packages by the authorities concerned. The Board of Governors of the Agency approved the revised regulations in June and September 1964. It authorized the Director General to apply them, as appropriate, to Agency operations and Agency assisted operations and to recommend to Member States and to the

SafeNet: a methodology for integrating general-purpose unsafe devices in safe-robot rehabilitation systems.

Science.gov (United States)

Vicentini, Federico; Pedrocchi, Nicola; Malosio, Matteo; Molinari Tosatti, Lorenzo

2014-09-01

Robot-assisted neurorehabilitation often involves networked systems of sensors ("sensory rooms") and powerful devices in physical interaction with weak users. Safety is unquestionably a primary concern. Some lightweight robot platforms and devices designed on purpose include safety properties using redundant sensors or intrinsic safety design (e.g. compliance and backdrivability, limited exchange of energy). Nonetheless, the entire "sensory room" shall be required to be fail-safe and safely monitored as a system at large. Yet, sensor capabilities and control algorithms used in functional therapies require, in general, frequent updates or re-configurations, making a safety-grade release of such devices hardly sustainable in cost-effectiveness and development time. As such, promising integrated platforms for human-in-the-loop therapies could not find clinical application and manufacturing support because of lacking in the maintenance of global fail-safe properties. Under the general context of cross-machinery safety standards, the paper presents a methodology called SafeNet for helping in extending the safety rate of Human Robot Interaction (HRI) systems using unsafe components, including sensors and controllers. SafeNet considers, in fact, the robotic system as a device at large and applies the principles of functional safety (as in ISO 13489-1) through a set of architectural procedures and implementation rules. The enabled capability of monitoring a network of unsafe devices through redundant computational nodes, allows the usage of any custom sensors and algorithms, usually planned and assembled at therapy planning-time rather than at platform design-time. A case study is presented with an actual implementation of the proposed methodology. A specific architectural solution is applied to an example of robot-assisted upper-limb rehabilitation with online motion tracking. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Making and Executing Decisions for Safe and Independent Living (MED-SAIL): development and validation of a brief screening tool.

Science.gov (United States)

Mills, Whitney L; Regev, Tziona; Kunik, Mark E; Wilson, Nancy L; Moye, Jennifer; McCullough, Laurence B; Naik, Aanand D

2014-03-01

Older adults prefer to remain in their own homes for as long as possible. The purpose of this article is to describe the development and preliminary validation of Making and Executing Decisions for Safe and Independent Living (MED-SAIL), a brief screening tool for capacity to live safely and independently in the community. Prospective preliminary validation study. Outpatient geriatrics clinic located in a community-based hospital. Forty-nine community-dwelling older adults referred to the clinic for a comprehensive capacity assessment. We examined internal consistency, criterion-based validity, concurrent validity, and accuracy of classification for MED-SAIL. The items included in MED-SAIL demonstrated internal consistency (5 items; α = 0.85). MED-SAIL was significantly correlated with the Independent Living Scales (r = 0.573, p ≤0.001) and instrumental activities of daily living (r = 0.440, p ≤0.01). The Mann-Whitney U test revealed significant differences between the no capacity and partial/full capacity classifications on MED-SAIL (U(48) = 60.5, Z = -0.38, p SAIL as a brief screening tool to identify older adults with impaired capacity for remaining safe and independent in their current living environment. MED-SAIL is useful tool for health and social service providers in the community for the purpose of referral for definitive capacity evaluation. Published by Elsevier Inc.

Changes in the regulations for the safe transport of radioactive material

International Nuclear Information System (INIS)

Lopez Vietri, Jorge R.; Vidal, Dora N.; Piumetti, Elsa H.; Capadona, Nancy M.

2000-01-01

The objective of this paper is to describe and to analyze the relevant changes, dealing with the design, operation and administrative requirements, to be introduced in the Revision 1 of the AR 10.16.1 standard 'Transport of radioactive material' that will be put into force on July, 1st 2001 by the Nuclear Regulatory Authority (competent authority of Argentina). In that way, the Revision 1 of the mentioned standard will be coincident with the 1996 edition (revised) of the 'Regulations for the safe transport of radioactive material', Safety Standards Series No. TS-R-1 (ST-1, revised) issued by the International Atomic Energy Agency (IAEA). (author)

Ademe et Vous. International Newsletter No. 44. The International Solar Alliance

International Nuclear Information System (INIS)

Gracy, Cecile; Dubourg, Laurence; Chazal, Olivier; Tsitsikalis, Alicia; Martin, Valerie; Seguin-Jacques, Catherine; Vermorel, Lucie; Aulas, Camille

2018-03-01

Although energy use is the biggest contributing factor to climate change, 1.1 billion people around the world still don't have access to electricity and 2.8 billion people don't have access to safe and clean cooking equipment, especially in Sub-Saharan Africa. The fight against climate change in those countries is thus closely linked to development issues. A number of international coalitions were created in the last few years in the follow-up to COP21 in order to meet this challenge. As part of this initiative, the first summit of the International Solar Alliance (ISA), launched by India and France during COP21, was held on 11 march 2018 in New Delhi in the presence of the French President Emmanuel Macron and the Indian Prime Minister, Narendra Modi. In this edition: - Focus: The International Solar Alliance; - Expertise: Investments for the Future programme, assesment; - Worldwide: MEDENER, improved dynamics

Implicit attitudes towards risky and safe driving

DEFF Research Database (Denmark)

Martinussen, Laila Marianne; Sømhovd, Mikael Julius; Møller, Mette

; further, self-reports of the intention to drive safely (or not) are socially sensitive. Therefore, we examined automatic preferences towards safe and risky driving with a Go/No-go Association Task (GNAT). The results suggest that (1) implicit attitudes towards driving behavior can be measured reliably...... with the GNAT; (2) implicit attitudes towards safe driving versus towards risky driving may be separable constructs. We propose that research on driving behavior may benefit from routinely including measures of implicit cognition. A practical advantage is a lesser susceptibility to social desirability biases......, compared to self-report methods. Pending replication in future research, the apparent dissociation between implicit attitudes towards safe versus risky driving that we observed may contribute to a greater theoretical understanding of the causes of unsafe and risky driving behavior....

Feedback control of a primary pump for safe and stable operation of a PIUS-type reactor

International Nuclear Information System (INIS)

Tasaka, K.; Imai, S.; Masaoka, H.; Tamaki, M.; Kukita, Y.

1993-01-01

A new automatic pump speed control system by using a measurement of the temperature distribution in the lower density lock is proposed for the PIUS-type reactor. This control system maintains the fluid temperature at the axial center of the lower density lock at the average of the fluid temperatures below and above the density lock in order to prevent the poison water from penetrating into the core during normal operation. The effectiveness of this control system was successfully confirmed by a series of experiments such as start-up and power ramping tests for the stable normal operation and a loss-of-feedwater test for the safe shutdown in an accident condition, using a small scale atmospheric pressure test loop which simulated the PIUS principle. (orig.)

Investigations of mechanical properties and Debye temperature of U2Ti

International Nuclear Information System (INIS)

Chattaraj, D.; Dash, Smruti; Kulkarni, S.G.

2012-01-01

U 2 Ti is a potential solid state material for safe storage, supply and recovery of hydrogen isotopes. It is not pyrophoric and its hydride is resistance to powdering upon hydrogenation. These two properties made this alloy advantageous over the conventionally used uranium as tritium getter material. Hence, thorough study of material properties like thermodynamic and elastic properties of U 2 Ti is important. Recently, present authors have reported thermodynamic functions for U 2 Ti. However, elastic moduli of this alloy have not been reported. The second derivatives of the internal energy with respect to strain, gives adiabatic elastic constants. Thus adiabatic elastic constants are related to interatomic potentials of material. They are also related to the thermal properties of a solid through the Debye theory. For metal hydride material, the elastic constants are useful for an evaluation of the elastic contribution to the hydrogen-hydrogen interaction energy and the elastic energy associated with the precipitation of hydride phases. The present paper reports the ultrasonic measurement of the elastic moduli and Debye temperature of U 2 Ti at room temperature using 38 DL plus ultrasonic velocitymeter

Prospects for inherently safe reactors

International Nuclear Information System (INIS)

Barkenbus, J.N.

1988-01-01

Public fears over nuclear safety have led some within the nuclear community to investigate the possibility of producing inherently safe nuclear reactors; that is, reactors that are transparently incapable of producing a core melt. While several promising designs of such reactors have been produced, support for large-scale research and development efforts has not been forthcoming. The prospects for commercialization of inherently safe reactors, therefore, are problematic; possible events such as further nuclear reactor accidents and superpower summits, could alter the present situation significantly. (author)

Temperature Pill

Science.gov (United States)

1988-01-01

Ingestible Thermal Monitoring System was developed at Johns Hopkins University as means of getting internal temperature readings for treatments of such emergency conditions as dangerously low (hypothermia) and dangerously high (hyperthermia) body temperatures. ITMS's accuracy is off no more than one hundredth of a degree and provides the only means of obtaining deep body temperature. System has additional applicability in fertility monitoring and some aspects of surgery, critical care obstetrics, metabolic disease treatment, gerontology (aging) and food processing research. Three-quarter inch silicone capsule contains telemetry system, micro battery, and a quartz crystal temperature sensor inserted vaginally, rectally, or swallowed.

50 CFR 216.91 - Dolphin-safe labeling standards.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 7 2010-10-01 2010-10-01 false Dolphin-safe labeling standards. 216.91... MAMMALS Dolphin Safe Tuna Labeling § 216.91 Dolphin-safe labeling standards. (a) It is a violation of... include on the label of those products the term “dolphin-safe” or any other term or symbol that claims or...

Medications: Using Them Safely

Science.gov (United States)

... to Safely Give Ibuprofen Childproofing and Preventing Household Accidents Medicines for Diabetes Complementary and Alternative Medicine How Do Pain Relievers Work? What Medicines Are and What They Do Medicines ...

Can oceanic reanalyses be used to assess recent anthropogenic changes and low-frequency internal variability of upper ocean temperature?

Energy Technology Data Exchange (ETDEWEB)

Corre, L.; Terray, L.; Weaver, A. [Cerfacs-CNRS, Toulouse (France); Balmaseda, M. [E.C.M.W.F, Reading (United Kingdom); Ribes, A. [CNRM-GAME, Meteo France-CNRS, Toulouse (France)

2012-03-15

A multivariate analysis of the upper ocean thermal structure is used to examine the recent long-term changes and decadal variability in the upper ocean heat content as represented by model-based ocean reanalyses and a model-independent objective analysis. The three variables used are the mean temperature above the 14 C isotherm, its depth and a fixed depth mean temperature (250 m mean temperature). The mean temperature above the 14 C isotherm is a convenient, albeit simple, way to isolate thermodynamical changes by filtering out dynamical changes related to thermocline vertical displacements. The global upper ocean observations and reanalyses exhibit very similar warming trends (0.045 C per decade) over the period 1965-2005, superimposed with marked decadal variability in the 1970s and 1980s. The spatial patterns of the regression between indices (representative of anthropogenic changes and known modes of internal decadal variability), and the three variables associated with the ocean heat content are used as fingerprint to separate out the different contributions. The choice of variables provides information about the local heat absorption, vertical distribution and horizontal redistribution of heat, this latter being suggestive of changes in ocean circulation. The discrepancy between the objective analysis and the reanalyses, as well as the spread among the different reanalyses, are used as a simple estimate of ocean state uncertainties. Two robust findings result from this analysis: (1) the signature of anthropogenic changes is qualitatively different from those of the internal decadal variability associated to the Pacific Interdecadal Oscillation and the Atlantic Meridional Oscillation, and (2) the anthropogenic changes in ocean heat content do not only consist of local heat absorption, but are likely related with changes in the ocean circulation, with a clear shallowing of the tropical thermocline in the Pacific and Indian oceans. (orig.)

A comparison and accuracy analysis of impedance-based temperature estimation methods for Li-ion batteries

NARCIS (Netherlands)

Beelen, H.P.G.J.; Raijmakers, L.H.J.; Donkers, M.C.F.; Notten, P.H.L.; Bergveld, H.J.

2016-01-01

In order to guarantee safe and proper use of Lithium-ion batteries during operation, an accurate estimate of the battery temperature is of paramount importance. Electrochemical Impedance Spectroscopy (EIS) can be used to estimate the battery temperature and several EIS-based temperature estimation

Identification of efforts required for continued safe operation of KANUPP

International Nuclear Information System (INIS)

Ghafoor, M.A.; Hashmi, J.A.; Siddiqui, Z.H.

1991-01-01

Kanupp, the first commercial CANDU PHWR, rated at 137 MWe, was built on turnkey basis by the Canadian General Electric Company for the Pakistan Atomic Energy Commission, and went operational in October, 1972 near Karachi. It has operated since then with a lifetime average availability factor of 51.5% and capacity factor of 25%. In 1976, Kanupp suffered loss of technical support from its original vendors due to the Canadian embargo on export of nuclear technology. Simultaneously, the world experienced the most explosive development and advancement in electronic and computer technology, accelerating the obsolescence of such equipment and systems installed in Kanupp. Replacement upgrading of obsolete computers, control and instrumentation was thus the first major set of efforts realized as essential f or continued safe operation. On the other hand, Kanupp was able to cope with the normal maintenance of its process, mechanical and electrical equipment till the late 80's. But now many of these components are reaching the end of their useful life, and developing chronic problems due to ageing, which can only be solved by complete replacement. This is much more difficult for custom-made nuclear process equipment, e.g. the reactor internals and the fuelling machine. Public awareness and international concern about nuclear safety have increased significantly since the TMI and Chernobyl events. Corresponding realization of the critical role of human factors and the importance of operational experience feedback, has helped Kanupp by opening international channels of communication, including renewed cooperation on CANDU technology. The safety standards and criteria for CANDU as well as other NPPs have matured and evolved gradually over the past two decades. First Kanupp has to ensure that its present ageing-induced equipment problems are resolved to satisfy the original safety requirements and public risk targets which are still internationally acceptable. But as a policy, we

Identification of efforts required for continued safe operation of KANUPP

Energy Technology Data Exchange (ETDEWEB)

Ghafoor, M A; Hashmi, J A; Siddiqui, Z H [Karachi Nuclear Power Plant, Karachi (Pakistan)

1991-04-01

Kanupp, the first commercial CANDU PHWR, rated at 137 MWe, was built on turnkey basis by the Canadian General Electric Company for the Pakistan Atomic Energy Commission, and went operational in October, 1972 near Karachi. It has operated since then with a lifetime average availability factor of 51.5% and capacity factor of 25%. In 1976, Kanupp suffered loss of technical support from its original vendors due to the Canadian embargo on export of nuclear technology. Simultaneously, the world experienced the most explosive development and advancement in electronic and computer technology, accelerating the obsolescence of such equipment and systems installed in Kanupp. Replacement upgrading of obsolete computers, control and instrumentation was thus the first major set of efforts realized as essential f or continued safe operation. On the other hand, Kanupp was able to cope with the normal maintenance of its process, mechanical and electrical equipment till the late 80's. But now many of these components are reaching the end of their useful life, and developing chronic problems due to ageing, which can only be solved by complete replacement. This is much more difficult for custom-made nuclear process equipment, e.g. the reactor internals and the fuelling machine. Public awareness and international concern about nuclear safety have increased significantly since the TMI and Chernobyl events. Corresponding realization of the critical role of human factors and the importance of operational experience feedback, has helped Kanupp by opening international channels of communication, including renewed cooperation on CANDU technology. The safety standards and criteria for CANDU as well as other NPPs have matured and evolved gradually over the past two decades. First Kanupp has to ensure that its present ageing-induced equipment problems are resolved to satisfy the original safety requirements and public risk targets which are still internationally acceptable. But as a policy, we

Implementation of Safe-by-Design for Nanomaterial Development and Safe Innovation: Why We Need a Comprehensive Approach.

Science.gov (United States)

Kraegeloh, Annette; Suarez-Merino, Blanca; Sluijters, Teun; Micheletti, Christian

2018-04-14

Manufactured nanomaterials (MNMs) are regarded as key components of innovations in various fields with high potential impact (e.g., energy generation and storage, electronics, photonics, diagnostics, theranostics, or drug delivery agents). Widespread use of MNMs raises concerns about their safety for humans and the environment, possibly limiting the impact of the nanotechnology-based innovation. The development of safe MNMs and nanoproducts has to result in a safe as well as functional material or product. Its safe use, and disposal at the end of its life cycle must be taken into account too. However, not all MNMs are similarly useful for all applications, some might bear a higher hazard potential than others, and use scenarios could lead to different exposure probabilities. To improve both safety and efficacy of nanotechnology, we think that a new proactive approach is necessary, based on pre-regulatory safety assessment and dialogue between stakeholders. On the basis of the work carried out in different European Union (EU) initiatives, developing and integrating MNMs Safe-by-Design and Trusted Environments (NANoREG, ProSafe, and NanoReg2), we present our point of view here. This concept, when fully developed, will allow for cost effective industrial innovation, and an exchange of key information between regulators and innovators. Regulators are thus informed about incoming innovations in good time, supporting a proactive regulatory action. The final goal is to contribute to the nanotechnology governance, having faster, cheaper, effective, and safer nano-products on the market.

Temperature fluctuations inside savanna termite mounds: Do size and plant shade matter?

Science.gov (United States)

Ndlovu, M; Pérez-Rodríguez, A

2018-05-01

Mound building termites are key ecosystem engineers of subtropical savanna regions. Mounds allow termites to maintain suitable conditions for termite reproduction and food cultivation ('fungus gardens'). We studied how the internal mound temperature of Macrotermes natalensis, a dominant mound-building termite of the subtropical savanna of southern Africa, responds to a number of environmental variables. We used general additive mixed models (GAMM) to determine how external temperature, mound size (volume) and the amount of vegetation shade affects mound internal temperature over a 24-h period. Internal mound temperature varied daily following changes of the external temperature, although the range of variation was much smaller. Active termite mounds maintained a higher internal temperature than inactive ones, and mound activity reinforced the positive effect of mound size and moderated the negative effect of vegetation shade on internal temperatures. In turn, external temperature fluctuations equally affected active and inactive mounds. Large mounds maintained near optimal internal temperatures compared to smaller sized mounds. We therefore conclude that termite mound size is a stronger determinant of internal mound temperature stability compared to plant shade cover. Copyright © 2018 Elsevier Ltd. All rights reserved.

Safe havens in Europe: Switzerland and the ten dwarfs

Directory of Open Access Journals (Sweden)

Martin Paldam

2013-12-01

Full Text Available Eleven safe havens exist in Europe providing offshore banking and low taxes. Ten of these states are very small while Switzerland is moderately small. All 11countries are richer than their large neighbors. It is shown that causality is from small to safe haven towealth, and that theoretically equilibriums are likely to exist where a certain regulation is substantially lower in a small country than in its big neighbor. This generates a large capital inflow to the safe havens. The pool of funds that may reach the safe havens is shown to be huge. It is far in excess of the absorptive capacity of the safe havens, but it still explains, why they are rich. Microstates offer a veil of anonymity to funds passing through, and Switzerland offers safe storage of funds.

Between Soft Legality and Strong Legitimacy : A Political Economy Approach to the Struggle for Basic Entitlements to Safe Water and Sanitation

NARCIS (Netherlands)

de Gaay Fortman, B.|info:eu-repo/dai/nl/068346581; Marcatelli, M.

2015-01-01

This article argues that the internationally declared “human right to safe water and sanitation,” although characterized by soft legality, may yet support universal access to such basic entitlements by virtue of its strong legitimacy. From a strategic perspective, human rights do indeed provide

Safe and Liquid Mortgage Bonds

DEFF Research Database (Denmark)

Dick-Nielsen, Jens; Gyntelberg, Jacob; Lund, Jesper

This paper shows that strict match pass-through funding of covered bonds provides safe and liquid mortgage bonds. Despite a 30% drop in house prices during the 2008 global crisis Danish mortgage bonds remained as liquid as most European government bonds. The Danish pass-through system effectively...... eliminates credit risk from the investor's perspective. Similar to other safe bonds, funding liquidity becomes the main driver of mortgage bond liquidity and this creates commonality in liquidity across markets and countries. These findings have implications for how to design a robust mortgage bond system...

An integrated approach to assessing the fracture safe margins of fusion reactor structures

International Nuclear Information System (INIS)

Odette, G.R.

1996-01-01

Design and operation of fusion reactor structures will require an appropriate data base closely coupled to a reliable failure analysis method to safely manage irradiation embrittlement. However, ongoing irradiation programs will not provide the information on embrittlement necessary to accomplish these objectives. A new engineering approach is proposed based on the concept of a master toughness-temperature curve indexed on an absolute temperature scale using shifts to account for variables such as size scales, crack geometry and loading rates as well as embrittlement. While providing a simple practical engineering expedient, the proposed method can also be greatly enhanced by fundamental mechanism based models of fracture and embrittlement. Indeed, such understanding is required for the effective use of small specimen test methods, which is a integral element in developing the necessary data base

Implementation of an Improved Safe Operating Envelope

International Nuclear Information System (INIS)

Prime, Robyn; McIntyre, Mark; Reeves, David

2008-01-01

This paper is a continuation of the paper presented at IYNC 2004 on 'The Definition of a Safe Operating Envelope'. The current paper concentrates on the implementation process of the Safe Operating Envelope employed at the Point Lepreau Generating Station. (authors)

Proposed apparatus for measuring internal friction in rocks at high temperatures and pressures: a design analysis

Energy Technology Data Exchange (ETDEWEB)

Bonner, B.P.

1977-10-03

An apparatus is described that measures internal friction in rocks at high temperatures (approximately 800/sup 0/C) and pressures (approximately 1.0 GPa). Steady oscillations (approximately 1.0 Hz) are induced in a jacketed sample while coaxial capacitive transducers monitor the resulting radial strain. Sample strains are continuously compared to the deformation of a low-loss standard, which acts as a stress transducer. The stress state produced is uniaxial stress. We use the theory of viscoelasticity to partition the loss into components depending on pure shear and dilatation. The theoretical results emphasize the importance of ultimately measuring each loss independently.

On the use of hydrogen in confined spaces: Results from the internal project InsHyde

NARCIS (Netherlands)

Venetsanos, A.G.; Adams, P.; Azkarate, I.; Bengaouer, A.; Brett, L.; Carcassi, M.N.; Engebø, A.; Gallego, E.; Gavrikov, A.I.; Hansen, O.R.; Hawksworth, S.; Jordan, T.; Kessler, A.; Kumar, S.; Molkov, V.; Nilsen, S.; Reinecke, E.; Stöcklin, M.; Schmidtchen, U.; Teodorczyk, A.; Tigreat, D.; Versloot, N.H.A.

2011-01-01

The paper presents an overview of the main achievements of the internal project InsHyde of the HySafe NoE. The scope of InsHyde was to investigate realistic small-medium indoor hydrogen leaks and provide recommendations for the safe use/storage of indoor hydrogen systems. Additionally, InsHyde

The GT-MHR - clear, economic, and safe power for the Pacific Rim

International Nuclear Information System (INIS)

Blue, L.S.; Etzel, K.T.; Simon, W.A.; Wistrom, J.D.

1994-01-01

In recent decades the nations of the Pacific Rim have outpaced the rest of the world in economic growth. Beyond an abundant labor market and the region's natural resources, energy has played a pivotal role in fuelling this boom. The diverse sources of this energy largely reflect the naturally occurring fuel assets in the Rim countries. Only in the countries where these resources are less plentiful has nuclear energy become a significant sources of electric power generation. Persuasive as the argument for non-polluting power may be by itself it does not sell the nuclear energy option. In addition to being clean it must also be economically competitive and very safe. The authors claim that the Gas-Turbine Modular Helium Reactor (GT-MHR) is an advances nuclear power system that addresses the issues, and should be viewed as an attractive candidate to meet future energy needs. The GT-MHR derives from the coupling of a small, passively safe, modular reactor directly with a compact power conversion module. It uses the Brayton cycle to produce electricity directly with the primary helium coolant driving the turbine-generator. Thus, it shows promise for a quantum reduction in power generation costs by increasing plant efficiency to a remarkable 48% This paper highlights the advantages of the fact that the design is based on proven technology, and offers a clean, economic and safe energy for electricity and high temperature process heat. 2 refs., 4 figs

International Conference of Ukrainian Nuclear Society ''NPP's safety and protection''(annotations)

International Nuclear Information System (INIS)

Barbashev, S.V.

1997-01-01

The abstracts of reports submitted to the Conference include: - New developments of the safe nuclear installations; - NPP ecological safety; - Methods of personnel and population protection; - Waste management safety (at transportation, processing and storage); - Spent nuclear fuel management; - NPP life extension and decommissioning; - Public opinion as an element of NPP safety; - Training of personnel, scientific support and safety culture; - Forecasting of nuclear power and industry safe development; - Development of international cooperation in nuclear power

Implementation of an Improved Safe Operating Envelope

Energy Technology Data Exchange (ETDEWEB)

Prime, Robyn; McIntyre, Mark [NB Power Nuclear, P.O. Box 600, Lepreau, NB (Canada); Reeves, David [Atlantic Nuclear Services Ltd., PO Box 1268 Fredericton, NB (Canada)

2008-07-01

This paper is a continuation of the paper presented at IYNC 2004 on 'The Definition of a Safe Operating Envelope'. The current paper concentrates on the implementation process of the Safe Operating Envelope employed at the Point Lepreau Generating Station. (authors)

Distribution of steady state temperatures and thermoelastic stresses in a cylindrical shell with internal heat generation and cooled on both sides or only on one side

International Nuclear Information System (INIS)

Melese d'Hospital, G.B.

1979-10-01

General expressions for steady state temperatures and elastic thermal stress distributions are derived for a hollow fuel element cooled on both sides. The main simplifying assumptions consist of one dimensional heat transfer and a single medium. Dimensionless numerical results are plotted in the case of uniform internal heat generation and for constant thermal conductivity. Solid rods and flat plates are treated as special cases. As could be expected, cooling on both sides rather than on only one side, leads to significant reduction in maximum fuel temperature and thermal stresses for a given power density, or to a significant increase in power density for either given maximum temperature drop in the fuel or for maximum tensile thermal stress. Typically, for a rod diameter ratio of 2, the power density could be increased by a factor of 3 to 4 without increasing the maximum stress. Similarly, for the same power density, replacing internal cooling of a hollow fuel element by external cooling reduces the maximum fuel temperature drop by a factor of 1.5 and the average fuel temperature drop (or maximum tensile stress) by a factor of 2, with the same maximum compressive stress

Low temperature safety of lithium-thionyl chloride cells

Science.gov (United States)

Subbarao, S.; Deligiannis, F.; Shen, D. H.; Dawson, S.; Halpert, G.

The use of lithium thionyl chloride cells for low-temperature applications is presently restricted because of their unsafe behavior. An attempt is made in the present investigation to identify the safe/unsafe low temperature operating conditions and to understand the low temperature cell chemistry responsible for the unsafe behavior. Cells subjected to extended reversal at low rate and -40 C were found to explode upon warm-up. Lithium was found to deposit on the carbon cathodes during reversal. Warming up to room temperature may be accelerating the lithium corrosion in the electrolyte. This may be one of the reasons for the cell thermal runaway.

The first safe country

Directory of Open Access Journals (Sweden)

Raffaela Puggioni

2012-06-01

Full Text Available The Dublin II Regulation makes the first safe country of refuge solelyresponsible for refugees and asylum seekers. In the case of Italy, thefirst responsible country has not been acting responsibly.

Karate: Keep It Safe.

Science.gov (United States)

Jordan, David

1981-01-01

Safety guidelines for each phase of a karate practice session are presented to provide an accident-free and safe environment for teaching karate in a physical education or traditional karate training program. (JMF)

Internal pump monitoring device

International Nuclear Information System (INIS)

Kurosaki, Toshikazu.

1996-01-01

In the present invention, a thermometer is disposed at the upper end of an internal pump casing of a coolant recycling system in a BWR type reactor to detect leakage of reactor water thereby ensuring the improvement of reliability of the internal pump. Namely, a thermometer is disposed, which can detect temperature elevation occurred when water in the internal pump leaked from a reactor pressure vessel passes through the gap between a stretch tube and an upper end of the pump casing. Signals from the thermometer are transmitted to a signal processing device by an instrumentation cable. The signal processing device generates an alarm when the temperature signal exceeds a predetermined value and announces that leakage of reactor water occurs in the internal pump. Since the present invention can detect the leakage of the reactor water in the pump casing in an early stage, it can contribute to the improvement of the safety and reliability of the internal pump. (I.S.)

Prepare to protect: Operating and maintaining a tornado safe room.

Science.gov (United States)

Herseth, Andrew; Goldsmith-Grinspoon, Jennifer; Scott, Pataya

2017-06-01

Operating and maintaining a tornado safe room can be critical to the effective continuity of business operations because a firm's most valuable asset is its people. This paper describes aspects of operations and maintenance (O&M) for existing tornado safe rooms as well as a few planning and design aspects that affect the ultimate operation of a safe room for situations where a safe room is planned, but not yet constructed. The information is based on several Federal Emergency Management Agency safe room publications that provide guidance on emergency management and operations, as well as the design and construction of tornado safe rooms.

SafeCare: An Innovative Approach for Improving Quality Through Standards, Benchmarking, and Improvement in Low- and Middle- Income Countries.

Science.gov (United States)

Johnson, Michael C; Schellekens, Onno; Stewart, Jacqui; van Ostenberg, Paul; de Wit, Tobias Rinke; Spieker, Nicole

2016-08-01

In low- and middle-income countries (LMICs), patients often have limited access to high-quality care because of a shortage of facilities and human resources, inefficiency of resource allocation, and limited health insurance. SafeCare was developed to provide innovative health care standards; surveyor training; a grading system for quality of care; a quality improvement process that is broken down into achievable, measurable steps to facilitate incremental improvement; and a private sector-supported health financing model. Three organizations-PharmAccess Foundation, Joint Commission International, and the Council for Health Service Accreditation of Southern Africa-launched SafeCare in 2011 as a formal partnership. Five SafeCare levels of improvement are allocated on the basis of an algorithm that incorporates both the overall score and weighted criteria, so that certain high-risk criteria need to be in place before a facility can move to the next SafeCare certification level. A customized quality improvement plan based on the SafeCare assessment results lists the specific, measurable activities that should be undertaken to address gaps in quality found during the initial assessment and to meet the nextlevel SafeCare certificate. The standards have been implemented in more than 800 primary and secondary facilities by qualified local surveyors, in partnership with various local public and private partner organizations, in six sub-Saharan African countries (Ghana, Kenya, Nigeria, Namibia, Tanzania, and Zambia). Expanding access to care and improving health care quality in LMICs will require a coordinated effort between institutions and other stakeholders. SafeCare's standards and assessment methodology can help build trust between stakeholders and lay the foundation for country-led quality monitoring systems.

Safe actinide disposition in molten salt reactors

International Nuclear Information System (INIS)

Gat, U.

1997-01-01

Safe molten salt reactors (MSR) can readily accommodate the burning of all fissile actinides. Only minor compromises associated with plutonium are required. The MSRs can dispose safely of actinides and long lived isotopes to result in safer and simpler waste. Disposing of actinides in MSRs does increase the source term of a safety optimized MSR. It is concluded that the burning and transmutation of actinides in MSRs can be done in a safe manner. Development is needed for the processing to handle and separate the actinides. Calculations are needed to establish the neutron economy and the fuel management. 9 refs

Safe Sleep for Babies

Science.gov (United States)

... 5 MB] Read the MMWR Science Clips Safe Sleep for Babies Eliminating hazards Recommend on Facebook Tweet ... Page Problem Every year, there are thousands of sleep-related deaths among babies. View large image and ...

Safety aspects of forced flow cooldown transients in modular high temperature gas-cooled reactors

International Nuclear Information System (INIS)

Kroeger, P.G.

1992-01-01

During some of the design basis accidents in Modular High Temperature Gas Cooled Reactors (MHTGRs) the main Heat Transport System (HTS) and the Shutdown Cooling System (SCS), are assumed to have failed. Decay heat is then removed by the passive Reactor Cavity Cooling System (RCCS) only. If either forced flow cooling system becomes available during such a transient, its restart could significantly reduce the down-time. This paper uses the THATCH code to examine whether such restart, during a period of elevated core temperatures, can be accomplished within safe limits for fuel and metal component temperatures. If the reactor is scrammed, either system can apparently be restarted at any time, without exceeding any safe limits. However, under unscrammed conditions a restart of forced cooling can lead to recriticality, with fuel and metal temperatures significantly exceeding the safety limits

The relative contributions of tropical Pacific sea surface temperatures and atmospheric internal variability to the recent global warming hiatus

Science.gov (United States)

Deser, Clara; Guo, Ruixia; Lehner, Flavio

2017-08-01

The recent slowdown in global mean surface temperature (GMST) warming during boreal winter is examined from a regional perspective using 10-member initial-condition ensembles with two global coupled climate models in which observed tropical Pacific sea surface temperature anomalies (TPAC SSTAs) and radiative forcings are specified. Both models show considerable diversity in their surface air temperature (SAT) trend patterns across the members, attesting to the importance of internal variability beyond the tropical Pacific that is superimposed upon the response to TPAC SSTA and radiative forcing. Only one model shows a close relationship between the realism of its simulated GMST trends and SAT trend patterns. In this model, Eurasian cooling plays a dominant role in determining the GMST trend amplitude, just as in nature. In the most realistic member, intrinsic atmospheric dynamics and teleconnections forced by TPAC SSTA cause cooling over Eurasia (and North America), and contribute equally to its GMST trend.

Safe motherhood -- from advocacy to action.

Science.gov (United States)

Tinker, A

1991-12-01

Every minute a woman dies from complications related to pregnancy or childbirth. That translates to 500,000 annually, of which, 99% live in developing countries. A woman in Africa has a 1:18 lifetime chance of dying from pregnancy-related causes, compared with a northern European woman who has a 1:10,000 chance. Thus, in 1987 international and regional agencies and national governments started a global program titled the Safe Motherhood Initiative. Its goal is to reduce maternal morbidity and mortality 50% by 2000. The death of a woman during pregnancy or child birth means that her surviving children are much more likely to die. In a bangladesh study it was found that the death of the mother was associated with a 200% increase in mortality for her sons and 350% for her daughters for children up to 10. Family planning is the key, since it is the single best tool of preventing these deaths, by reducing the number of times a woman gets pregnant. Family planning also reduces the number of abortions which are estimated to kill 200,000 women annually in developing countries. Trained midwives who can provide obstetrical emergency assistance will also make a large impact. Risk assessment was once considered very important, but studies have shown that the majority of pregnancy complications develop without being detected. Further, the number of women with risk factors that develop complications is much lower than the number of women who develop complications during pregnancy. So monitoring women with risk factors misses most complications. Regular monitoring and medical examinations are much more effective for preventing complications. Safe motherhood can only be achieved if each program is tailored to the needs of the community. Donor nations are necessary for this program to succeed, but ultimate success rests in the hands of each country. National priorities must be set, resources must be allocated, and programs must be designed to be effective.

Escola segura Safe school

Directory of Open Access Journals (Sweden)

Edson Ferreira Liberal

2005-11-01

Full Text Available OBJETIVO: Revisão das estratégias para tornar o ambiente escolar seguro. Inicialmente os autores contextualizam a violência e os acidentes no ambiente escolar e fazem recomendações, baseadas em dados da literatura, para a implantação de escolas seguras. FONTE DE DADOS: Artigos publicados entre 1993 e 2005 na base de dados MEDLINE. Dados nacionais epidemiológicos e da literatura também foram pesquisados. SÍNTESE DOS DADOS: Há evidência crescente de que a intervenção tem múltiplos componentes. O foco político é a prática em educação em saúde com o envolvimento de toda a comunidade. O norte dessas intervenções é ajudar estudantes e toda a comunidade a adotar um comportamento seguro e saudável. As escolas estão assumindo um envolvimento crescente na promoção da saúde, prevenção de doenças e prevenção de trauma. Nesse contexto de prevenção de causas externas de morbimortalidade, é importante reconhecer o risco ambiental, locais e comportamentos de risco como favoráveis ao trauma e à violência, além de um novo conceito de acidentes como algo que possa ser evitado. CONCLUSÃO: A implementação da escola segura representa uma nova direção promissora para o trabalho preventivo baseado na escola. É importante notar que uma escola segura deve intervir não meramente na sua estrutura física, mas também torná-la tão segura quanto possível, trabalhando com a comunidade escolar por meio de educação em saúde, discutindo principalmente o comportamento saudável.OBJECTIVE: To review the strategies to make school a safe environment. The paper first addresses the social context of accidents and violence in the school environment, and makes recommendations, based on the literature data, for the implementation of safe schools. SOURCE OF DATA: Articles published between 1993 and 2005 in the MEDLINE database. Brazilian epidemiological and literature data have also been searched. SUMMARY OF THE FINDINGS: There is

Buying & Using Medicine Safely

Science.gov (United States)

... Reducers Safe Daily Use of Aspirin Medication Health Fraud Resources for You FDA Consumer Updates (Drugs) Page ... feeds Follow FDA on Twitter Follow FDA on Facebook View FDA videos on YouTube View FDA photos ...

PEGylation of Phytantriol-Based Lyotropic Liquid Crystalline Particles-The Effect of Lipid Composition, PEG Chain Length, and Temperature on the Internal Nanostructure

DEFF Research Database (Denmark)

Nilsson, Christa; Ostergaard, Jesper; Larsen, Susan Weng

2014-01-01

of these lipidic nonlamellar liquid crystalline particles by using DSPE-mPEGs with three different block lengths of the hydrophilic PEG segment. The effects of lipid composition, PEG chain length, and temperature on the morphology and internal nanostructure of these self-assembled lipidic aqueous dispersions based...

Stochastic field theory and finite-temperature supersymmetry

International Nuclear Information System (INIS)

Ghosh, P.; Bandyopadhyay, P.

1988-01-01

The finite-temperature behavior of supersymmetry is considered from the viewpoint of stochastic field theory. To this end, it is considered that Nelson's stochastic mechanics may be generalized to the quantization of a Fermi field when the classical analog of such a field is taken to be a scalar nonlocal field where the internal space is anisotropic in nature such that when quantized this gives rise to two internal helicities corresponding to fermion and antifermion. Stochastic field theory at finite temperature is then formulated from stochastic mechanics which incorporates Brownian motion in the external space as well as in the internal space of a particle. It is shown that when the anisotropy of the internal space is suppressed so that the internal time ξ 0 vanishes and the internal space variables are integrated out one has supersymmetry at finite temperature. This result is true for T = 0, also. However, at this phase equilibrium will be destroyed. Thus for a random process van Hove's result involving quantum mechanical operators, i.e., that when supersymmetry remains unbroken at T = 0 it will also remain unbroken at Tnot =0, occurs. However, this formalism indicates that when at T = 0 broken supersymmetry results, supersymmetry may be restored at a critical temperature T/sub c/

Time-saving and fail-safe dissection method for vestibulocochlear organs in gross anatomy classes.

Science.gov (United States)

Suzuki, Ryoji; Konno, Naoaki; Ishizawa, Akimitsu; Kanatsu, Yoshinori; Funakoshi, Kodai; Akashi, Hideo; Zhou, Ming; Abe, Hiroshi

2017-09-01

Because the vestibulocochlear organs are tiny and complex, and are covered by the petrous part of the temporal bone, they are very difficult for medical students to dissect and visualize during gross anatomy classes. Here, we report a time-saving and fail-safe procedure we have devised, using a hand-held hobby router. Nine en bloc temporal bone samples from donated human cadavers were used as trial materials for devising an appropriate procedure for dissecting the vestibulocochlear organs. A hand-held hobby router was used to cut through the temporal bone. After trials, the most time-saving and fail-safe method was selected. The performance of the selected method was assessed by a survey of 242 sides of 121 cadavers during gross anatomy classes for vestibulocochlear dissection. The assessment was based on the observation ratio. The best procedure appeared to be removal of the external acoustic meatus roof and tympanic cavity roof together with removal of the internal acoustic meatus roof. The whole procedure was completed within two dissection classes, each lasting 4.5 hr. The ratio of surveillance for the chorda tympani and three semicircular canals by students was significantly improved during 2013 through 2016. In our dissection class, "removal of the external acoustic meatus roof and tympanic cavity roof together with removal of the internal acoustic meatus roof" was the best procedure for students in the limited time available. Clin. Anat. 30:703-710, 2017. © 2017Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Virus Alert: Ten Steps to Safe Computing.

Science.gov (United States)

Gunter, Glenda A.

1997-01-01

Discusses computer viruses and explains how to detect them; discusses virus protection and the need to update antivirus software; and offers 10 safe computing tips, including scanning floppy disks and commercial software, how to safely download files from the Internet, avoiding pirated software copies, and backing up files. (LRW)

Internal variability in a 1000-yr control simulation with the coupled climate model ECHO-G - I. Near-surface temperature, precipitation and mean sea level pressure.

Energy Technology Data Exchange (ETDEWEB)

Min, Seung-Ki; Hense, Andreas [Univ. of Bonn (Germany). Meteorological Inst.; Legutke, Stephanie [Max Planck Inst. for Meteorology, Hamburg (Germany); Kwon, Won-Tae [Meteorological Research Inst., Seoul (Korea, Republic of)

2005-08-01

The internal variability in a 1000-yr control simulation with the coupled atmosphere/ocean global climate model ECHO-G is analysed using near-surface temperature, precipitation and mean sea level pressure variables, and is compared with observations and other coupled climate model simulations. ECHO-G requires annual mean flux adjustments for heat and freshwater in order to simulate no significant climate drift for 1000 yr, but no flux adjustments for momentum. The ECHO-G control run captures well most aspects of the observed seasonal and annual climatology and of the interannual to decadal variability of the three variables. Model biases are very close to those in ECHAM4 (atmospheric component of ECHO-G) stand-alone integrations with prescribed observed sea surface temperature. A trend comparison between observed and modelled near-surface temperatures shows that the observed near-surface global warming is larger than internal variability produced by ECHO-G, supporting previous studies. The simulated global mean near-surface temperatures, however, show a 2-yr spectral peak which is linked with a strong biennial bias of energy in the El Nino Southern Oscillation signal. Consequently, the interannual variability (39 yr) is underestimated.

Oesophageal heat exchangers with a diameter of 11mm or 14.7mm are equally effective and safe for targeted temperature management.

Directory of Open Access Journals (Sweden)

Daniel C Schroeder

Full Text Available Targeted temperature management (TTM is widely used in critical care settings for conditions including hepatic encephalopathy, hypoxic ischemic encephalopathy, meningitis, myocardial infarction, paediatric cardiac arrest, spinal cord injury, traumatic brain injury, ischemic stroke and sepsis. Furthermore, TTM is a key treatment for patients after out-of-hospital cardiac-arrest (OHCA. However, the optimal cooling method, which is quick, safe and cost-effective still remains controversial. Since the oesophagus is adjacent to heart and aorta, fast heat-convection to the central blood-stream could be achieved with a minimally invasive oesophageal heat exchanger (OHE. To date, the optimal diameter of an OHE is still unknown. While larger diameters may cause thermal- or pressure-related tissue damage after long-term exposure to the oesophageal wall, smaller diameter (e.g., gastric tubes, up to 11mm may not provide effective cooling rates. Thus, the objective of the study was to compare OHE-diameters of 11mm (OHE11 and 14.7mm (OHE14.7 and their effects on tissue and cooling capability.Pigs were randomized to OHE11 (N = 8 or OHE14.7 (N = 8. After cooling, pigs were maintained at 33°C for 1 hour. After 10h rewarming, oesophagi were analyzed by means of histopathology. The oesophagus of four animals from a separate study that underwent exactly the identical preparation and cooling protocol described above but received a maintenance period of 24h were used as histopathological controls.Mean cooling rates were 2.8±0.4°C°C/h (OHE11 and 3.0±0.3°C °C/h (OHE14.7; p = 0.20. Occasional mild acute inflammatory transepithelial infiltrates were found in the cranial segment of the oesophagus in all groups including controls. Deviations from target temperature were 0.1±0.4°C (OHE11 and 0±0.1°C (OHE14.7; p = 0.91. Rewarming rates were 0.19±0.07°C °C/h (OHE11 and 0.20±0.05°C °C/h (OHE14.7; p = 0.75.OHE with diameters of 11 mm and 14.7 mm achieve

Safe driving for teens

Science.gov (United States)

Driving and teenagers; Teens and safe driving; Automobile safety - teenage drivers ... months before taking friends as passengers. Teenage-related driving deaths occur more often in certain conditions. OTHER SAFETY TIPS FOR TEENS Reckless driving is still a ...

Regulations for the safe management of radioactive wastes and spent nuclear fuel

International Nuclear Information System (INIS)

Voica, Anca

2007-01-01

The paper presents the national, international and European regulations regarding radioactive waste management. ANDRAD is the national authority charged with nation wide coordination of safe management of spent fuel and radioactive waste including their final disposal. ANDRAD's main objectives are the following: - establishing the National Strategy concerning the safety management of radioactive waste and spent nuclear fuel; - establishing the national repositories for the final disposal of the spent nuclear fuel and radioactive waste; - developing the technical procedures and establishing norms for all stages of management of spent nuclear fuel and radioactive waste, including the disposal and the decommissioning of the nuclear and radiologic facilities

A simulation model for predicting the temperature during the application of MR-guided focused ultrasound for stroke treatment using pulsed ultrasound

Science.gov (United States)

Hadjisavvas, V.; Damianou, C.

2011-09-01

In this paper a simulation model for predicting the temperature during the application of MR-guided focused ultrasound for stroke treatment using pulsed ultrasound is presented. A single element spherically focused transducer of 5 cm diameter, focusing at 10 cm and operating at either 0.5 MHz or 1 MHz was considered. The power field was estimated using the KZK model. The temperature was estimated using the bioheat equation. The goal was to extract the acoustic parameters (power, pulse duration, duty factor and pulse repetition frequency) that maintain a temperature increase of less than 1 °C during the application of a pulse ultrasound protocol. It was found that the temperature change increases linearly with duty factor. The higher the power, the lower the duty factor needed to keep the temperature change to the safe limit of 1 °C. The higher the frequency the lower the duty factor needed to keep the temperature change to the safe limit of 1 °C. Finally, the deeper the target, the higher the duty factor needed to keep the temperature change to the safe limit of 1 °C. The simulation model was tested in brain tissue during the application of pulse ultrasound and the measured temperature was in close agreement with the simulated temperature. This simulation model is considered to be very useful tool for providing acoustic parameters (frequency, power, duty factor, pulse repetition frequency) during the application of pulsed ultrasound at various depths in tissue so that a safe temperature is maintained during the treatment. This model could be tested soon during stroke clinical trials.

Predominance of neurologic diseases in international aeromedical transportation.

Science.gov (United States)

Chen, Wan-Lin; Lin, Yu-Ming; Ma, Hong-Ping; Chiu, Wen-Ta; Tsai, Shin-Han

2009-12-01

International travel industry in Taiwan is expanding. The number of people traveling abroad was approximately 480,000 people in 1980; 2,940,000 in 1990; 7,320,000 in 2000, and in 2007, it has reached 8,960,000, which was more than one third of total population. Air medical transportation will be necessary when local medical facilities do not approximate the international standards. No previous study on epidemiology in Taiwan on patients received international medical repatriation. This is the first report to discuss the epidemiology of Taiwan's international aeromedical transportation and its focus on neurologic diseases. Retrospective analysis of all international aeromedical transports on Taiwanese patients from October 2005 to September 2007 was performed. All materials were collected from the databank of International SOS, Taipei. The data were analyzed with Microsoft Excel and SPSS v. 11.0 software (SPSS, Chicago, Ill). A total of 416 patients were transported. Excluding expatriates transported outbound and 2-stage inbound transports, the Taiwanese patient number with international aeromedical transport was 379; 51 by air ambulance and 328 commercially. There were 271 male (72%) and 108 female patients (18%). Of the 379 patients, 178 (47%) were neurologic diseases. Two hundred ninety-five (78%) patients were transported from China. Patient transports peaked in autumn by 105 (28%). Of all 33 ventilated patients, 12 (36%) were neurologic diseases. In-flight complications occurred in 10% of neurologic and 2% of nonneurologic cases. No in-flight mortality occurred in both groups. Neurologic diseases comprise most of the Taiwanese patients that requires medical transportation. With relatively suboptimal medical standard and high medical expenses in China, patients with neurologic conditions need timely and safe aeromedical transport than those with other diseases. Transport of patients with neurologic diseases, either by air ambulance or commercial flights, can

The international radioactive transportation regulations: A model for national regulations

International Nuclear Information System (INIS)

Pope, R.B.; Rawl, R.R.

1990-06-01

The International Atomic Energy Agency's (IAEA) Regulations for the Safe Transport of Radioactive Material, Safety Series No. 6 (herein after denoted as the ''International Regulations'') serve as the model for the regulations for individual countries and international modal organizations controlling the packaging and transportation of radioactive materials. The purpose of this paper is to outline the background and history of the International Regulations, the general principles behind the requirements of the International Regulations, the structure and general contents of the latest edition of the International Regulations, and the roles of various international bodies in the development and implementation of the International Regulations and the current status of regulatory and supportive document development at both the international and domestic level. This review will provide a basis for users and potential users to better understand the source and application of the International Regulations. 1 tab

Influence of anisotropy effect and internal stresses upon the superconductive critical temperature of plastically deformed tin

International Nuclear Information System (INIS)

Wagner, D.; Stangler, F.

1976-01-01

The influence of plastic deformation on the superconductive critical temperature of tin single crystals has been investigated experimentally. It was shown by measurements that the lattice defects produced by plastic deformation lead to an anisotropy effect (according to the theory of Markowitz and Kadanoff), as do impurities in alloyed material. The decrease in T/sub c/ due to this effect can be measured, however, only with samples of certain special orientations. Samples with other orientations show an increase in T/sub c/, which can be explained by the assumption of internal stresses from dislocation pileups. A model is discussed which accounts for the measured rise in T/sub c/

Elaboration of Safe Community Assessment System

Directory of Open Access Journals (Sweden)

Birutė Mikulskienė

2013-08-01

Full Text Available The paper aims to design an assessment system to monitor and evaluate safety parameters and administrative efforts with the purpose to increase safety in municipalities. The safety monitoring system considered is to be the most important tool for creation and development of safe communities in Lithuania. Several methods were applied to achieve this purpose. In order to determine the role of local government in ensuring the safety of people, property and environment at the local level of a meta-analysis of research reports, the Lithuanian national legislation, strategic planning documents of the state and local government were carried out. Analysis of statistical data, structural analysis, comparative analysis and synthesis methods were used while investigating the areas of safety uncertainty, risk groups, identifying safety risk factors, determining their relationship, and creating a safe community assessment system. A safe community assessment system, which consists of two types of criteria, has been elaborated. The assessment system is based on the multi-level criteria for safety monitoring and the multi-level criteria for the evaluation of municipal activities in the field of building safety. Links between the criteria, peculiarities of their application and advantages in the process of safe community creation and development are analyzed. Design and implementation of the safe community assessment system is one of the most important stages to implement the idea of safe communities. The proposed system integrates a variety of risk areas, the safety achievement criteria are linked to the criteria used in the strategic planning. Periodic assessment of the safety situation using the proposed system ensures possibility to monitor current local safety conditions and assess the changes and the trends. A safe community assessment system is proposed to be used as a tool to unified municipalities safety comprehensiveness and compare safety level in

Elaboration of Safe Community Assessment System

Directory of Open Access Journals (Sweden)

Algirdas Astrauskas

2011-12-01

Full Text Available The paper aims to design an assessment system to monitor and evaluate safety parameters and administrative efforts with the purpose to increase safety in municipalities. The safety monitoring system considered is to be the most important tool for creation anddevelopment of safe communities in Lithuania. Several methods were applied to achieve this purpose. In order to determine the role of local government in ensuring the safety of people, property and environment at the local level of a meta-analysis of research reports,the Lithuanian national legislation, strategic planning documents of the state and local government were carried out. Analysis of statistical data, structural analysis, comparative analysis and synthesis methods were used while investigating the areas of safety uncertainty, risk groups, identifying safety risk factors, determining their relationship, and creating a safe community assessment system.A safe community assessment system, which consists of two types of criteria, has been elaborated. The assessment system is based on the multi-level criteria for safety monitoring and the multi-level criteria for the evaluation of municipal activities in the field of building safety. Links between the criteria, peculiarities of their application and advantages in the process of safe community creation and development are analyzed.Design and implementation of the safe community assessment system is one of the most important stages to implement the idea of safe communities. The proposed system integrates a variety of risk areas, the safety achievement criteria are linked to the criteria used in thestrategic planning. Periodic assessment of the safety situation using the proposed system ensures possibility to monitor current local safety conditions and assess the changes and the trends. A safe community assessment system is proposed to be used as a tool to unified municipalities safety comprehensiveness and compare safety level in

Safe use of nanomaterials

CERN Multimedia

2013-01-01

The use of nanomaterials  is on the increase worldwide, including at CERN. The HSE Unit has established a safety guideline to inform you of the main requirements for the safe handling and disposal of nanomaterials at CERN.   A risk assessment tool has also been developed which guides the user through the process of evaluating the risk for his or her activity. Based on the calculated risk level, the tool provides a list of recommended control measures.   We would therefore like to draw your attention to: Safety Guideline C-0-0-5 - Safe handling and disposal of nanomaterials; and Safety Form C-0-0-2 - Nanomaterial Risk Assessment   You can consult all of CERN’s safety rules and guidelines here. Please contact the HSE Unit for any questions you may have.   The HSE Unit

25 CFR 700.55 - Decent, safe, and sanitary dwelling.

Science.gov (United States)

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Decent, safe, and sanitary dwelling. 700.55 Section 700... PROCEDURES General Policies and Instructions Definitions § 700.55 Decent, safe, and sanitary dwelling. (a) General. The term decent, safe, and sanitary dwelling means a dwelling which— (1) Meets applicable federal...

Experimental results showing the internal three-component velocity field and outlet temperature contours for a model gas turbine combustor

CSIR Research Space (South Africa)

Meyers, BC

2011-09-01

Full Text Available by the American Institute of Aeronautics and Astronautics Inc. All rights reserved ISABE-2011-1129 EXPERIMENTAL RESULTS SHOWING THE INTERNAL THREE-COMPONENT VELOCITY FIELD AND OUTLET TEMPERATURE CONTOURS FOR A MODEL GAS TURBINE COMBUSTOR BC Meyers*, GC... identifier c Position identifier F Fuel i Index L (Combustor) Liner OP Orifice plate Introduction There are often inconsistencies when comparing experimental and Computational Fluid Dynamics (CFD) simulations for gas turbine combustors [1...

Design of an internal dosimetry program

International Nuclear Information System (INIS)

Wu, C.F.; Goff, T.E.

2004-01-01

Measurement of radiation dose is an essential element of radiation protection programs at nuclear facilities. To protect workers and demonstrate compliance with regulatory requirements, dosimetry programs must be established based on sound technical basis. Historically, external exposure was controlled by occupational dose limits. Internal exposure to radionuclides was limited by maximum permissible body burden and maximum permissible concentration. With the issuance of ICRP 26, ICRP 30, DOE Order 5480.11, DOE/EH-0256T, and the new 10 CFR 20, it has become a requirement that internal dose be assessed and the sum of internal and external doses be maintained below regulatory limits. Nuclear facilities are required to have internal dose evaluation programs adequate to demonstrate compliance with radiation protection standards (RPSs). The Waste Isolation Pilot Plant is a DOE facility designed to demonstrate safe disposal of transuranic (TRU) wastes in an ancient salt bed 2,150 feet underground. Internal dose measurement is required to support waste handling activities. This paper describes the technical basis for the WIPP Internal Dosimetry Program. (author)

Transfer pricing and safe harbours

Directory of Open Access Journals (Sweden)

Veronika Solilová

2013-01-01

Full Text Available Transfer prices are significant for both taxpayers and tax administrations because they determine in large part taxable profits of associated enterprises in different tax jurisdictions. Moreover, in the context of taxation, transfer prices must be complied with the arm’s length principle. However, Multinational Enterprises have been faced daily by conflicting rules and approaches to applying the arm’s length principle, burdensome documentation requirements, inconsistent audit standards and unpredictable competent authority outcomes. Therefore, the Committee on Fiscal Affairs launched another project on the administrative aspects of transfer pricing in 2010. On 16 May 2013 as a partial solution of this project was approved by the OECD Council the Revised Section E on Safe Harbours in Chapter IV of the Transfer Pricing Guidelines for Multinational Enterprises and Tax Authorities. The paper is focused on significant changes of newly approved chapter IV of the Transfer Pricing Guidelines for Multinational Enterprises and Tax Authorities, further on analysis of practice in this area, on advantages and disadvantages of safe harbours for taxpayers and competent authorities with aim to suggest recommendations on use of safe harbours in the Czech Republic.

A methodology for thermodynamic simulation of high temperature, internal reforming fuel cell systems

Science.gov (United States)

Matelli, José Alexandre; Bazzo, Edson

This work presents a methodology for simulation of fuel cells to be used in power production in small on-site power/cogeneration plants that use natural gas as fuel. The methodology contemplates thermodynamics and electrochemical aspects related to molten carbonate and solid oxide fuel cells (MCFC and SOFC, respectively). Internal steam reforming of the natural gas hydrocarbons is considered for hydrogen production. From inputs as cell potential, cell power, number of cell in the stack, ancillary systems power consumption, reformed natural gas composition and hydrogen utilization factor, the simulation gives the natural gas consumption, anode and cathode stream gases temperature and composition, and thermodynamic, electrochemical and practical efficiencies. Both energetic and exergetic methods are considered for performance analysis. The results obtained from natural gas reforming thermodynamics simulation show that the hydrogen production is maximum around 700 °C, for a steam/carbon ratio equal to 3. As shown in the literature, the found results indicate that the SOFC is more efficient than MCFC.

STRRAP system-A software for hazardous materials risk assessment and safe distances calculation

International Nuclear Information System (INIS)

Godoy, S.M.; Santa Cruz, A.S.M.; Scenna, N.J.

2007-01-01

This work presents a powerful computational tool (Stochastic Toxic Release Risk Assessment Package, STRRAP) useful in risk assessment and emergency planning (safe distance calculation), which allows to handle the stochastic uncertainty of atmospheric parameters, critical for risk calculation when diffusion of hazardous gases or particulate matter occur as a consequence of an emission or accidental release. In fact, the random behaviour of wind intensity, wind direction, atmospheric stability and temperature, given a time horizon, (a season or a complete year), is taken into account considering also the day or night condition. STRRAP can be used for releases or emissions from static sources (for example a stack or a fixed tank in a facility) or from transportation accidents (road, rail, maritime and pipeline transport) involving different scenarios. After a stochastic simulation based on well-known diffusion models (dense and light gases, particulate matter) is carried out, the downwind pollutant concentrations are obtained, in order to compute safe distances and/or individual and societal risks. Some study cases are analyzed to show STRRAP capabilities

Intrinsically Safe and Economical Reactor (ISER)

International Nuclear Information System (INIS)

Wakabayashi, Hiroaki; Asahi, Yoshiro

1991-01-01

The Intrinsically Safe and Economical Reactor (ISER) is designed based on the principle of a process inherent ultimate safe reactor, PIUS, a so-called inherently safe reactor (ISR). ISER has been developed joingly by the members of the Kanagawa Institute of Technology, the University of Tokyo, the Japan Atomic Energy Research Institute (JAERI) and several industrial firms in Japan. This paper describes the requirements for the next generation of power reactor, the safety design philosphy of ISR and ISER, the controllability of ISER and the results of analyses of some of the design-based accidents (DBA) of ISER, namely station blackout, accidents in which the pressurizer relief valve becomes jammed and stuck in open position and tube breaks in the steam generator. It is concluded that the ISER can ensure a wide range of contraollabitily and fuel integrity for all the analysed DBAs. (orig.)

PREFACE: Proceedings of the 25th International Conference on Low Temperature Physics (LT25) (Amsterdam, The Netherlands, 6-13 August 2008) Proceedings of the 25th International Conference on Low Temperature Physics (LT25) (Amsterdam, The Netherlands, 6-13 August 2008)

Science.gov (United States)

Kes, Peter; Jochemsen, Reijer

2009-04-01

This issue forms part I of the Proceedings of the 25th International Conference on Low Temperature Physics (LT25) (Amsterdam, The Netherlands, 67-13 August 2008). The majority of the special invited lectures, such as the London prize lectures, the international union of pure and applied physics (IUPAP) young scientist award lectures, the plenary, half-plenary and public lectures, and the historical lectures presented at the LT25 conference, are included. The papers relating to the oral and poster presentations will appear in part II of the proceedings in a dedicated open access issue of Journal of Physics: Conference Series (2009 J. Phys.: Conf. Ser. 150). In addition to the organizer's report and a summary of the new developments in low temperature physics, which can also be found in this issue, part II provides useful information about LT25, such as an overview of committees, sponsors, exhibitors, and some conference statistics. To ensure the high publication standard mandated by Journal of Physics: Condensed Matter and Journal of Physics: Conference Series every paper was reviewed by at least one referee before it was accepted for publication. The editors are indebted to many colleagues for invaluable assistance in the preparation and review of 900 papers appearing in both parts I and II of these proceedings. In particular, we would like to thank Carlo Beenakker, Jeroen van den Brink, Hans Brom, Jos de Jongh, Horst Rogalla, Fons de Waele, and Jan Zaanen.

Elevated temperature effects on concrete properties

International Nuclear Information System (INIS)

Grant, P.R.; Gruber, R.S.; Van Katwijk, C.

1993-08-01

The design of facilities to process or store radioactive wastes presents many challenging engineering problems. Such facilities must not only provide for safe storage of radioactive wastes but they must also be able to maintain confinement of these materials during and after natural phenomena events. Heat generated by the radioactive decay of the wastes will cause the temperature of the concrete containment structure to increase to a magnitude higher than that found in conventional structures. These elevated temperatures will cause strength-related concrete properties to degrade over time. For concrete temperatures less than 150 degree F, no reduction in strength is taken and the provisions of ACI 349, which states that higher temperatures are allowed if tests are provided to evaluate the reduction in concrete strength properties, apply. Methods proposed in a Pacific Northwest Laboratory (PNL) report, Modeling of Time-Variant Concrete Properties at Elevated Temperatures, can be used to evaluate the effects of elevated temperatures on concrete properties. Using these modified concrete properties the capacity of a concrete structure, subjected to elevated temperatures, to resist natural phenomena hazards can be determined

Internal friction in uranium dioxide

International Nuclear Information System (INIS)

Paulin Filho, Pedro Iris

1979-01-01

The uranium dioxide inelastic properties were studied measuring internal friction at low frequencies (of the order of 1 Hz). The work was developed in the 160 to 400 deg C temperature range. The effect of stoichiometry variation was studied oxidizing the sample with consequent change of the defect structure originally present in the non-stoichiometric uranium dioxide. The presence of a wide and irregular peak due to oxidation was observed at low temperatures. Activation energy calculations indicated the occurrence of various relaxation processes and assuming the existence of a peak between - 80 and - 70 deg C , the absolute value obtained for the activation energy (0,54 eV) is consistent with the observed values determined at medium and high frequencies for the stress induced reorientation of defects. The microstructure effect on the inelastic properties was studied for stoichiometric uranium dioxide, by varying grain size and porosity. These parameters have influence on the high temperature measurements of internal friction. The internal friction variation for temperatures higher than 340 deg C is thought to be due to grain boundary relaxation phenomena. (author)

A safe and accurate method to perform esthetic mandibular contouring surgery for Far Eastern Asians.

Science.gov (United States)

Hsieh, A M-C; Huon, L-K; Jiang, H-R; Liu, S Y-C

2017-05-01

A tapered mandibular contour is popular with Far Eastern Asians. This study describes a safe and accurate method of using preoperative virtual surgical planning (VSP) and an intraoperative ostectomy guide to maximize the esthetic outcomes of mandibular symmetry and tapering while mitigating injury to the inferior alveolar nerve (IAN). Twelve subjects with chief complaints of a wide and square lower face underwent this protocol from January to June 2015. VSP was used to confirm symmetry and preserve the IAN while maximizing the surgeon's ability to taper the lower face via mandibular inferior border ostectomy. The accuracy of this method was confirmed by superimposition of the perioperative computed tomography scans in all subjects. No subjects complained of prolonged paresthesia after 3 months. A safe and accurate protocol for achieving an esthetic lower face in indicated Far Eastern individuals is described. Copyright © 2016 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Regulations for the safe transport of radioactive material

International Nuclear Information System (INIS)

1995-01-01

Regulations and rules for the safe transport of radioactive materials by all kinds of conveyance are offered. Different types of packages and the conditions associated with the methods of safe packaging are given

Tympanic membrane temperature decreases during head up tilt

DEFF Research Database (Denmark)

Lorr, David; Lund, Anton; Fredrikson, Mats

2017-01-01

INTRODUCTION: Changes in blood flow influence temperature of surrounding tissues. Since the internal carotid artery (ICA) and internal jugular vein (IJV) neighbor the tympanic membrane, changes in their blood flow most likely determine changes in tympanic membrane temperature (TMT). We sought to ...

Temperature measurement in the flowing medium

Directory of Open Access Journals (Sweden)

Sedlák Kamil

2018-01-01

Full Text Available The article deals with a brief description of methods of temperature measurements in a flowing water steam. Attention is paid to the measurement of pseudo static temperature by a single sealed thermocouple entering the flowing liquid through the flown-by wall. Then three types of probes for stagnation temperature measurement are shown, whose properties were tested using CFD calculations. The aim was to design a probe of stagnation parameters of described properties which can be used for measuring flow parameters in a real steam turbine. An important factor influencing the construction is not only the safe manipulation of the probe when inserting and removing it from the machine in operation, but also the possibility to traverse the probe along the blade length.

Large scale international bioenergy trading. How bioenergy trading can be reliazed under safe and sustainable frame conditions?

DEFF Research Database (Denmark)

Holm-Nielsen, Jens Bo; Kirchovas, Simas

2011-01-01

Biomass sources as Woodchips – Wood pellets, Straw – Bio pellets, animal manure, farm-by products and new cropping systems are integrated in our society’s needs. The mindset for shifting from fossil fuels based economies into sustainable energy economies already exist. Bioenergy utilization systems...... sustainability criteria. The sustainability criteria agreed internationally could be realized as a tool to secure the positive impacts of bioenergy and to foster the international trade. This study investigates the developments by national and international bodies of biomass standardization and certification...

U.K. policy responses to international influences - nuclear power

International Nuclear Information System (INIS)

Jones, P.M.S.

1978-01-01

An account is given of U.K. participation in international discussions directed towards the safe development and application of nuclear power. Particular attention is given to the International Fuel Cycle Evaluation (INFCE), which is stated to be looking at the whole question of proliferation and the merits and disadvantages of a range of alternative fuel cycles and nuclear power strategies. A summary is also given of U.K. participation in work on radiological protection (through the I.C.R.P.) and radioactive waste disposal. International cooperation in research and development is mentioned. Public involvement in policy making is also discussed briefly. (U.K.)

Estimation of internal heat transfer coefficients and detection of rib positions in gas turbine blades from transient surface temperature measurements

International Nuclear Information System (INIS)

Heidrich, P; Wolfersdorf, J v; Schmidt, S; Schnieder, M

2008-01-01

This paper describes a non-invasive, non-destructive, transient inverse measurement technique that allows one to determine internal heat transfer coefficients and rib positions of real gas turbine blades from outer surface temperature measurements after a sudden flow heating. The determination of internal heat transfer coefficients is important during the design process to adjust local heat transfer to spatial thermal load. The detection of rib positions is important during production to fulfill design and quality requirements. For the analysis the one-dimensional transient heat transfer problem inside of the turbine blade's wall was solved. This solution was combined with the Levenberg-Marquardt method to estimate the unknown boundary condition by an inverse technique. The method was tested with artificial data to determine uncertainties with positive results. Then experimental testing with a reference model was carried out. Based on the results, it is concluded that the presented inverse technique could be used to determine internal heat transfer coefficients and to detect rib positions of real turbine blades.

Effect of rotational speed modulation on heat transport in a fluid layer with temperature dependent viscosity and internal heat source

Directory of Open Access Journals (Sweden)

B.S. Bhadauria

2014-12-01

Full Text Available In this paper, a theoretical investigation has been carried out to study the combined effect of rotation speed modulation and internal heating on thermal instability in a temperature dependent viscous horizontal fluid layer. Rayleigh–Bénard momentum equation with Coriolis term has been considered to describe the convective flow. The system is rotating about it is own axis with non-uniform rotational speed. In particular, a time-periodic and sinusoidally varying rotational speed has been considered. A weak nonlinear stability analysis is performed to find the effect of modulation on heat transport. Nusselt number is obtained in terms of amplitude of convection and internal Rayleigh number, and depicted graphically for showing the effects of various parameters of the system. The effect of modulated rotation speed is found to have a stabilizing effect for different values of modulation frequency. Further, internal heating and thermo-rheological parameters are found to destabilize the system.

THE CONSEQUENCES OF GLOBALIZATION UPON SAFE TOURISM

Directory of Open Access Journals (Sweden)

Svetlana Mihić

2009-11-01

Full Text Available Globalization, a phenomenon on the rise, is characterized by the free cross-bor- der movement of individuals, technologies, and capital. It has far- reaching consequen- ces for tourism, too, as it implies travel for leisure and business, and correspondingly, financial transfers between various nation states. Startinf from the status quo in the field, the current paper sets out to analyze the consequences and implications of globalization upon safe tourism and conduct a marketing research into the perceptions of consumers upon Serbia as a safe vacation destination for the purpose of safe tourism. Finally the research results will be presented and several solutions will be provided for improving security in tourism zones

Sun Safe Mode Controller Design for LADEE

Science.gov (United States)

Fusco, Jesse C.; Swei, Sean S. M.; Nakamura, Robert H.

2015-01-01

This paper presents the development of sun safe controllers which are designed to keep the spacecraft power positive and thermally balanced in the event an anomaly is detected. Employed by NASA's Lunar Atmosphere and Dust Environment Explorer (LADEE), the controllers utilize the measured sun vector and the spacecraft body rates for feedback control. To improve the accuracy of sun vector estimation, the least square minimization approach is applied to process the sensor data, which is proven to be effective and accurate. To validate the controllers, the LADEE spacecraft model engaging the sun safe mode was first simulated and then compared with the actual LADEE orbital fight data. The results demonstrated the applicability of the proposed sun safe controllers.

Influencing behaviour for safe working environments

OpenAIRE

Boer, de, J. (Johannes); Teeuw, W.B. (Wouter)

2011-01-01

Safety at work The objective of the project Safety at Work is to increase safety at the workplace by applying and combining state of the art artefacts from personal protective equipment and ambient intelligence technology. In this state of the art document we focus on the developments with respect to how (persuasive) technology can help to influence behaviour in a natural, automatic way in order to make industrial environments safer. We focus on personal safety, safe environments and safe beh...

Now, It's Your Turn: How You Can Take Medicine Safely

Science.gov (United States)

... turn Javascript on. Feature: Taking Medicines Safely Now, It's Your Turn: How You Can Take Medicine Safely ... medicine. The pharmacist has filled the prescription. Now it's up to you to take the medicine safely. ...

Internal shorting and fuel loss of a low temperature solid oxide fuel cell with SDC electrolyte

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xinge; Robertson, Mark; Deces-Petit, Cyrille; Qu, Wei; Kesler, Olivera; Maric, Radenka; Ghosh, Dave [Institute for Fuel Cell Innovation, National Research Council Canada, 4250 Wesbrook Mall, Vancouver, BC V6T 1W5 (Canada)

2007-02-10

A solid oxide fuel cell with Sm{sub 0.2}Ce{sub 0.8}O{sub 1.9} (SDC) electrolyte of 10 {mu}m in thickness and Ni-SDC anode of 15 {mu}m in thickness on a 0.8 mm thick Ni-YSZ cermet substrate was fabricated by tape casting, screen printing and co-firing. A composite cathode, 75 wt.% Sm{sub 0.5}Sr{sub 0.5}CoO{sub 3} (SSCo) + 25 wt.% SDC, approximately 50 {mu}m in thickness, was printed on the co-fired half-cell, and sintered at 950 C. The cell showed a high electrochemical performance at temperatures ranging from 500 to 650 C. Peak power density of 545 mW cm{sup -2} at 600 C was obtained. However, the cell exhibited severe internal shorting due to the mixed conductivity of the SDC electrolyte. Both the amount of water collected from the anode outlet and the open circuit voltage (OCV) indicated that the internal shorting current could reach 0.85 A cm{sup -2} or more at 600 C. Zr content inclusions were found at the surface and in the cross-section of the SDC electrolyte, which could be one of the reasons for reduced OCV and oxygen ionic conductivity. Fuel loss due to internal shorting of the thin SDC electrolyte cell becomes a significant concern when it is used in applications requiring high fuel utilization and electrical efficiency. (author)

Knock-limited performance of several internal coolants

Science.gov (United States)

Bellman, Donald R; Evvard, John C

1945-01-01

The effect of internal cooling on the knock-limited performance of an-f-28 fuel was investigated in a CFR engine, and the following internal coolants were used: (1) water, (2), methyl alcohol-water mixture, (3) ammonia-methyl alcohol-water mixture, (4) monomethylamine-water mixture, (5) dimethylamine-water mixture, and (6) trimethylamine-water mixture. Tests were run at inlet-air temperatures of 150 degrees and 250 degrees F. to indicate the temperature sensitivity of the internal-coolant solutions.

Touch Temperature Coating for Off-the-Shelf Electrical Equipment Used on Spacecraft

Science.gov (United States)

Ungar, Eugene K.; Brady, Timothy K.

2010-01-01

Off-the-shelf electrical equipment is frequently used in space-based applications to control costs. However, the reduced heat transfer in the spacecraft microgravity environment causes the equipment to operate at significantly higher temperatures than it would in terrestrial applications. This creates touch temperature issues where items particularly metallic ones become too hot for the crew to handle safely. A touch temperature coating layup has been developed that can be added to spacebased electrically powered hardware. The coating allows the crew to safely handle the hardware, but only slightly impedes the heat transfer from the component during normal operation. In the present work, the coating generic requirements are developed and a layup is described that meets these specifications. Analytical and experimental results are presented that demonstrate the ability of the coating layup to increase the allowable limits of touch temperature while only marginally degrading heat transfer to the environment. This allows the spacecraft crew to handle objects that, if not coated, would be hot enough to cause pain or skin damage.

Evaluation of green tea extract as a safe personal hygiene against viral infections.

Science.gov (United States)

Lee, Yun Ha; Jang, Yo Han; Kim, Young-Seok; Kim, Jinku; Seong, Baik Lin

2018-01-01

Viral infections often pose tremendous public health concerns as well as economic burdens. Despite the availability of vaccines or antiviral drugs, personal hygiene is considered as effective means as the first-hand measure against viral infections. The green tea catechins, in particular, epigallocatechin-3-gallate (EGCG), are known to exert potent antiviral activity. In this study, we evaluated the green tea extract as a safe personal hygiene against viral infections. Using the influenza virus A/Puerto Rico/8/34 (H1N1) as a model, we examined the duration of the viral inactivating activity of green tea extract (GTE) under prolonged storage at various temperature conditions. Even after the storage for 56 days at different temperatures, 0.1% GTE completely inactivated 10 6 PFU of the virus (6 log 10 reduction), and 0.01% and 0.05% GTE resulted in 2 log 10 reduction of the viral titers. When supplemented with 2% citric acid, 0.1% sodium benzoate, and 0.2% ascorbic acid as anti-oxidant, the inactivating activity of GTE was temporarily compromised during earlier times of storage. However, the antiviral activity of the GTE was steadily recovered up to similar levels with those of the same concentrations of GTE without the supplements, effectively prolonging the duration of the virucidal function over extended period. Cryo-EM and DLS analyses showed a slight increase in the overall size of virus particles by GTE treatment. The results suggest that the virucidal activity of GTE is mediated by oxidative crosslinking of catechins to the viral proteins and the change of physical properties of viral membranes. The durability of antiviral effects of GTE was examined as solution type and powder types over extended periods at various temperature conditions using human influenza A/H1N1 virus. GTE with supplements demonstrated potent viral inactivating activity, resulting in greater than 4 log 10 reduction of viral titers even after storage for up to two months at a wide range of

Safe clinical practice for patients hospitalised in a suicidal crisis: a study protocol for a qualitative case study.

Science.gov (United States)

Berg, Siv Hilde; Rørtveit, Kristine; Walby, Fredrik A; Aase, Karina

2017-01-27

Suicide prevention in psychiatric care is arguably complex and incompletely understood as a patient safety issue. A resilient healthcare approach provides perspectives through which to understand this complexity by understanding everyday clinical practice. By including suicidal patients and healthcare professionals as sources of knowledge, a deeper understanding of what constitutes safe clinical practice can be achieved. This planned study aims to adopt the perspective of resilient healthcare to provide a deeper understanding of safe clinical practice for suicidal patients in psychiatric inpatient care. It will describe the experienced components and conditions of safe clinical practice and the experienced practice of patient safety. The study will apply a descriptive case study approach consisting of qualitative semistructured interviews and focus groups. The data sources are hospitalised patients in a suicidal crisis and healthcare professionals in clinical practice. This study was approved by the Regional Ethics Committee (2016/34). The results will be disseminated through scientific articles, a PhD dissertation, and national and international conferences. These findings can generate knowledge to be integrated into the practice of safety for suicidal inpatients in Norway and to improve the feasibility of patient safety measures. Theoretical generalisations can be drawn regarding safe clinical practice by taking into account the experiences of patients and healthcare professionals. Thus, this study can inform the conceptual development of safe clinical practice for suicidal patients. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Frugal Biotech Applications of Low-Temperature Plasma.

Science.gov (United States)

Machala, Zdenko; Graves, David B

2017-09-01

Gas discharge low-temperature air plasma can be utilized for a variety of applications, including biomedical, at low cost. We term these applications 'frugal plasma' - an example of frugal innovation. We demonstrate how simple, robust, low-cost frugal plasma devices can be used to safely disinfect instruments, surfaces, and water. Copyright © 2017 Elsevier Ltd. All rights reserved.

The origin and evolution of safe-yield policies in the Kansas groundwater management districts

Science.gov (United States)

Sophocleous, M.

2000-01-01

The management of groundwater resources in Kansas continues to evolve. Declines in the High Plains aquifer led to the establishment of groundwater management districts in the mid-1970s and reduced streamflows prompted the enactment of minimum desirable streamflow standards in the mid-1980s. Nonetheless, groundwater levels and streamflows continued to decline, although at reduced rates compared to premid-1980s rates. As a result, "safe-yield" policies were revised to take into account natural groundwater discharge in the form of stream baseflow. These policies, although a step in the right direction, are deficient in several ways. In addition to the need for more accurate recharge data, pumping-induced streamflow depletion, natural stream losses, and groundwater evapotranspiration need to be accounted for in the revised safe-yield policies. Furthermore, the choice of the 90% flow-duration statistic as a measure of baseflow needs to be reevaluated, as it significantly underestimates mean baseflow estimated from baseflow separation computer programs; moreover, baseflow estimation needs to be refined and validated. ?? 2000 International Association for Mathematical Geology.

Is nuclear power safe enough

Energy Technology Data Exchange (ETDEWEB)

Andresen, A F [Institutt for Atomenergi, Kjeller (Norway)

1979-01-01

The lecture formed a commentary on the report of the Norwegian Government's Commission on Nuclear power Safety which was published in October 1978. It was introductorily pointed out that 'safe' and 'safety' are not in themselves meaningful terms and that the probability of an occurrence is the real measure. The main items in the Commission's report have been core meltdown, releases during reprocessing, waste disposal, plutonium diversion and environmental impacts. The 21 members of the Commission were unanimous in 7 of the 8 chapters. In chapter 2, 'Summary and Conclusions', 3 members dissented from the majority opinion, that, subject to certain conditions, nuclear power was a safe and acceptable source of energy.

Modular high-temperature reactor launched (and wallchart)

International Nuclear Information System (INIS)

Steinwarz, W.

1987-01-01

In view of the need for a technically unsophisticated, safe and economic reactor system, the KWU group has integrated the experience gained from German light-water reactor engineering and from successful operation of the German AVR experimental high-temperature reactor into the development of the High-Temperature Reactor (HTR)-module. The main components are illustrated and explained and technical data for the HTR-module is given. Safety is also considered. This includes graphs of core heat-up temperature for pebble-bed HTR and a graph of the temperature load of the fuel elements. The operation, control and applications are considered. The latter includes use in combined heat and power generation and community heating. Feasibility studies have shown that the HTR-module is cheaper, comparatively, than coal-fired power stations. (U.K.)

A 'simple anterior fish excluder' (SAFE for mitigating penaeid-trawl bycatch.

Directory of Open Access Journals (Sweden)

Matthew J McHugh

Full Text Available Various plastic strips and sheets (termed 'simple anterior fish excluders'-SAFEs were positioned across the openings of penaeid trawls in attempts at reducing the unwanted bycatches of small teleosts. Initially, three SAFEs (a single wire without, and with small and large plastic panels were compared against a control (no SAFE on paired beam trawls. All SAFEs maintained targeted Metapenaeus macleayi catches, while the largest plastic SAFE significantly reduced total bycatch by 51% and the numbers of Pomatomus saltatrix, Mugil cephalus and Herklotsichthys castelnaui by up to 58%. A redesigned SAFE ('continuous plastic' was subsequently tested (against a control on paired otter trawls, significantly reducing total bycatch by 28% and P. saltatrix and H. castelnaui by up to 42%. The continuous-plastic SAFE also significantly reduced M. macleayi catches by ~7%, but this was explained by ~5% less wing-end spread, and could be simply negated through otter-board refinement. Further work is required to refine the tested SAFEs, and to quantify species-specific escape mechanisms. Nevertheless, the SAFE concept might represent an effective approach for improving penaeid-trawl selectivity.

The safe transport of radioactive materials

CERN Document Server

Gibson, R

1966-01-01

The Safe Transport of Radioactive Materials is a handbook that details the safety guidelines in transporting radioactive materials. The title covers the various regulations and policies, along with the safety measures and procedures of radioactive material transport. The text first details the 1963 version of the IAEA regulation for the safe transport of radioactive materials; the regulation covers the classification of radionuclides for transport purposes and the control of external radiation hazards during the transport of radioactive materials. The next chapter deals with concerns in the im

Definition of the «Economic Security of an Enterprise» and «Safe Development of an Enterprise» Notions

Directory of Open Access Journals (Sweden)

Yefimova Ganna V.

2013-11-01

Full Text Available The necessity of this study is explained by difference of opinions regarding understanding of the “economic security of an enterprise” notion, on the one hand, and the poorly studied issue of a combination of the process of enterprise development with a necessary task of ensuring a high level of its economic security, on the other hand. Analysing, systemising and generalising results of scientific studies, the article identifies that economic security of an enterprise is an economic category, which characterises the enterprise functioning conditions. Favourable conditions of functioning ensure a high level of stability and steadiness of an enterprise and its ability of self-realisation and expanded self-reproduction. This becomes possible if an enterprise is capable of resisting external threats and preventing internal ones. Since development of an enterprise is an objective process, which takes place under conditions of uncertainty and changeability of external and internal environments, it is accompanied with a system of threats, which the system of economic security should protect an enterprise from. Taking into account the above, safe development of an enterprise is a process of consecutive transitions of the economic system from one state to another, which is not of a poorer quality than a previous one, which envisages producing new goals and creation of safe conditions for transition from one specific goal, achieved in the process of enterprise functioning, to another. The proposed definitions allow consideration of such significant issues of methodology of management of safe development of an enterprise as the diagnostics of its level and planning.

Combined SAFE/SNAP approach to safeguards evaluation

International Nuclear Information System (INIS)

Engi, D.; Chapman, L.D.; Grant, F.H.; Polito, J.

1980-01-01

Generally, the scope of a safeguards evaluation model can efficiently address one of two issues, (1) global safeguards effectiveness, or (2) vulnerability analysis for individual scenarios. The Safeguards Automated Facility Evaluation (SAFE) focuses on (1) while the Safeguards Network Analysis Procedure (SNAP) is directed at (2). SAFE addresses (1) in that it considers the entire facility, i.e., the composite system of hardware and human components, in one global analysis. SNAP addresses (2) by providing a safeguards modeling symbology sufficiently flexible to represent quite complex scenarios from the standpoint of hardware interfaces while also accounting for a rich variety of human decision making. A combined SAFE/SNAP approach to the problem of safeguards evaluation is described and illustrated through an example

The pros and cons of safe electronuclear station with accelerator as a driver

International Nuclear Information System (INIS)

Svistunov, Yu.A.; Vorogushin, M.F.; Gavrish, Yu.N.; Kudinovich, I.V.; Struev, V.P.

2001-01-01

Creation of 200 MW compact safe energetic installation on a base of a high-temperature, gas-cooled,subcritical reactor was discussed in paper. Chain reaction was initiated by the outer neutron flow. It was proposed to obtain such a source by irradiation of different substances with an intensive proton beam from the linac. Now possibilities of such a scheme are considered in more details.Structure of the reactor active zone is discussed. The use of the cyclotron as a driver is considered as an alternative variant. Problems of reliability, radiation safety and cost of installation are taken into account too

The pros and cons of safe electronuclear station with accelerator as a driver

CERN Document Server

Svistunov, Y A; Gavrish, Y N; Kudinovich, I V; Struev, V P

2001-01-01

Creation of 200 MW compact safe energetic installation on a base of a high-temperature, gas-cooled,subcritical reactor was discussed in paper. Chain reaction was initiated by the outer neutron flow. It was proposed to obtain such a source by irradiation of different substances with an intensive proton beam from the linac. Now possibilities of such a scheme are considered in more details.Structure of the reactor active zone is discussed. The use of the cyclotron as a driver is considered as an alternative variant. Problems of reliability, radiation safety and cost of installation are taken into account too.

LACK OF AWARENESS ABOUT SAFE BLOOD IN PAKISTANI POPULATION

Directory of Open Access Journals (Sweden)

Muhammad Usman

2014-12-01

Full Text Available Blood transfusion is a life saving procedure in various transfusion-dependent life threatening conditions and donation of safe blood is a prerequisite for achieving this goal. This study was designed to evaluate the awareness regarding “safe blood” in Pakistani population. This study was conducted at a large scale through a population survey. The test population was divided into two groups i.e. general population and students. The Performa was designed for a general and student population and included 20 questions related to awareness of safe blood. A total of 4900 individuals belonging to different ethnic groups were included in this population survey. Results of social survey were analyzed by using Usman and Moin awareness chart. Results of this study revealed profound unawareness about safe blood in Pakistani population. This study found lack of awareness about safe blood as a major factor that is playing a vital role in the propagation of blood borne diseases in Pakistan. To secure the recipients from blood borne complications through blood donation, it is necessary to create effective awareness about safe blood in Pakistani population.

Development of Safe Food Handling Guidelines for Korean Consumers.

Science.gov (United States)

Kang, Hee-Jin; Lee, Min-Woo; Hwang, In-Kyeong; Kim, Jeong-Weon

2015-08-01

The purpose of this study was to develop guidelines for Korean consumers with regard to safe food handling practices at home by identifying current food handling issues. Korean consumers' behaviors regarding their safe food handling were identified via survey questionnaires that included items on individual hygiene practices, prepreparation steps when cooking, the cooking process, and the storage of leftover foods. The subjects were 417 Korean parents with elementary school children living in Seoul and Gyeonggi Province in the central area of Korea. The survey results revealed gaps between the knowledge or practices of Korean consumers and scientific evidence pertaining to safe food handling practices. Based on these findings, a leaflet on safe food handling guidelines was developed in accordance with Korean food culture. These guidelines suggest personal hygiene practices as well as fundamental principles and procedures for safe food handling from the stage of food purchase to that of keeping leftover dishes. A pilot application study with 50 consumers revealed that the guidelines effectively improved Korean consumers' safe food handling practices, suggesting that they can serve as practical educational material suitable for Korean consumers.

Classical entropy generation analysis in cooled homogenous and functionally graded material slabs with variation of internal heat generation with temperature, and convective–radiative boundary conditions

International Nuclear Information System (INIS)

Torabi, Mohsen; Zhang, Kaili

2014-01-01

This article investigates the classical entropy generation in cooled slabs. Two types of materials are assumed for the slab: homogeneous material and FGM (functionally graded material). For the homogeneous material, the thermal conductivity is assumed to be a linear function of temperature, while for the FGM slab the thermal conductivity is modeled to vary in accordance with the rule of mixtures. The boundary conditions are assumed to be convective and radiative concurrently, and the internal heat generation of the slab is a linear function of temperature. Using the DTM (differential transformation method) and resultant temperature fields from the DTM, the local and total entropy generation rates within slabs are derived. The effects of physically applicable parameters such as the thermal conductivity parameter for the homogenous slab, β, the thermal conductivity parameter for the FGM slab, γ, gradient index, j, internal heat generation parameter, Q, Biot number at the right side, Nc 2 , conduction–radiation parameter, Nr 2 , dimensionless convection sink temperature, δ, and dimensionless radiation sink temperature, η, on the local and total entropy generation rates are illustrated and explained. The results demonstrate that considering temperature- or coordinate-dependent thermal conductivity and radiation heat transfer at both sides of the slab have great effects on the entropy generation. - Highlights: • The paper investigates entropy generation in a slab due to heat generation and convective–radiative boundary conditions. • Both homogeneous material and FGM (functionally graded material) were considered. • The calculations are carried out using the differential transformation method which is a well-tested analytical technique

IAEA mode-related research in the safe transport of radioactive material

Energy Technology Data Exchange (ETDEWEB)

Blalock, L.G.; Rawl, R.R. [International Atomic Energy Agency, IAEA, Vienna (Austria)

1998-07-01

The International Atomic Energy Agency sponsors Co-ordinated Research Programmes (CRP) in the safe transport of radioactive material. The CRPs are intended to encourage research by Member States in identified areas and to facilitate co-ordination of exchange of information and resources to reach a common understanding of the problem and alternative solutions. Two of these programmes are: Accident Severity at Sea During the Transport of Radioactive Material and Accident Severity During the Air Transport of Radioactive Material. This paper will discuss these two programmes and their relationship to the continuing regulatory revision process and interfaces with the International Maritime Organization (IMO) and the International Civil Aviation Organization (ICAO). Some Member States and non-governmental organizations in IMO meetings expressed concerns that accidents on board ships may be more severe than the IAEA regulatory tests account for, and that package failure with subsequent release of radioactive material may occur. The CRP on accident severity at sea was established to develop further quantitative information on potential accident severities during the transport of radioactive material by ships. The primary objective of this programme is to collect and evaluate statistical data of marine accidents, perform analyses of potential accident conditions and evaluate the risks resulting from such shipments. The CRP on air transport was established to make a major international effort to collect relevant frequency and severity data and to analyze it so the accident forces to which a packages of radioactive material might be subjected to in a severe air accident can be more confidently quantified. Several countries have ongoing data collection activities related to aircraft accidents and severity and other sources of statistics for in-flight aircraft accidents will be explored. The International Civil Aviation Organization informed the IAEA of their plans to improve

IAEA mode-related research in the safe transport of radioactive material

International Nuclear Information System (INIS)

Blalock, L.G.; Rawl, R.R.

1998-01-01

The International Atomic Energy Agency sponsors Co-ordinated Research Programmes (CRP) in the safe transport of radioactive material. The CRPs are intended to encourage research by Member States in identified areas and to facilitate co-ordination of exchange of information and resources to reach a common understanding of the problem and alternative solutions. Two of these programmes are: Accident Severity at Sea During the Transport of Radioactive Material and Accident Severity During the Air Transport of Radioactive Material. This paper will discuss these two programmes and their relationship to the continuing regulatory revision process and interfaces with the International Maritime Organization (IMO) and the International Civil Aviation Organization (ICAO). Some Member States and non-governmental organizations in IMO meetings expressed concerns that accidents on board ships may be more severe than the IAEA regulatory tests account for, and that package failure with subsequent release of radioactive material may occur. The CRP on accident severity at sea was established to develop further quantitative information on potential accident severities during the transport of radioactive material by ships. The primary objective of this programme is to collect and evaluate statistical data of marine accidents, perform analyses of potential accident conditions and evaluate the risks resulting from such shipments. The CRP on air transport was established to make a major international effort to collect relevant frequency and severity data and to analyze it so the accident forces to which a packages of radioactive material might be subjected to in a severe air accident can be more confidently quantified. Several countries have ongoing data collection activities related to aircraft accidents and severity and other sources of statistics for in-flight aircraft accidents will be explored. The International Civil Aviation Organization informed the IAEA of their plans to improve

Relationship between alertness, performance, and body temperature in humans

Science.gov (United States)

Wright, Kenneth P Jr; Hull, Joseph T.; Czeisler, Charles A.

2002-01-01

Body temperature has been reported to influence human performance. Performance is reported to be better when body temperature is high/near its circadian peak and worse when body temperature is low/near its circadian minimum. We assessed whether this relationship between performance and body temperature reflects the regulation of both the internal biological timekeeping system and/or the influence of body temperature on performance independent of circadian phase. Fourteen subjects participated in a forced desynchrony protocol allowing assessment of the relationship between body temperature and performance while controlling for circadian phase and hours awake. Most neurobehavioral measures varied as a function of internal biological time and duration of wakefulness. A number of performance measures were better when body temperature was elevated, including working memory, subjective alertness, visual attention, and the slowest 10% of reaction times. These findings demonstrate that an increased body temperature, associated with and independent of internal biological time, is correlated with improved performance and alertness. These results support the hypothesis that body temperature modulates neurobehavioral function in humans.

Impact of international and local conditions on sovereign bond spreads: International evidence

Directory of Open Access Journals (Sweden)

Selma Izadi

2018-03-01

Full Text Available This paper examines the effect of international and domestic factors on the sovereign bond spreads for 22 developed countries in North America, Europe and Pacific Rim regions. First, for all the regions the impact of global factors on the sovereign bond spreads is more intense than regional factors. Second, the findings confirm that for the bond spreads of each region over its domestic government bonds, the countries’ local fundamentals are better determinants of the spreads compared to the spread over US government bonds as a safe haven. Third, the influence of worldwide factors in the Eurozone compared to other regions bond spreads is less. Fourth, the relationship of the market sentiment and the investor risk aversion with the sovereign bond spreads of all regions is positive. Equity market volatility plays significant role in yield speads in international bond markets.

Guide to the design, testing and use of packaging for the safe transport of radioactive materials

International Nuclear Information System (INIS)

1976-01-01

This guide gives to designers, manufacturers and users of packaging, advice supplementary to, or in amplification of, the recommendations made by the International Atomic Energy Agency for the safe transport of radioactive materials as given in IAEA Safety Series No. 6 (1973) and the advisory material given in IAEA Safety Series No. 37 (1973). This guide should be read and used in conjunction with these recommendations, the appropriate national regulations and any applicable regulations or requirements of the carriers concerned. (author)

Fiber Bragg Gratings for High-Temperature Thermal Characterization

International Nuclear Information System (INIS)

Stinson-Bagby, Kelly L.; Fielder, Robert S.

2004-01-01

Fiber Bragg grating (FBG) sensors were used as a characterization tool to study the SAFE-100 thermal simulator at the Nasa Marshal Space Flight Center. The motivation for this work was to support Nasa space nuclear power initiatives through the development of advanced fiber optic sensors for space-based nuclear power applications. Distributed high temperature measurements, up to 1150 deg. C, were made with FBG temperature sensors. Additionally, FBG strain measurements were taken at elevated temperatures to provide a strain profile of the core during operation. This paper will discuss the contribution of these measurements to meet the goals of Nasa Marshall Space Flight Center's Propulsion Research Center. (authors)

Safe-haven CDS Premia

DEFF Research Database (Denmark)

Klingler, Sven; Lando, David

We argue that Credit Default Swap (CDS) premia for safe-haven sovereigns, like Germany and the United States, are driven to a large extent by regulatory requirements under which derivatives dealing banks have an incentive to buy CDS to hedge counterparty credit risk of their counterparties. We...

International Aspects of Nuclear Safety

International Nuclear Information System (INIS)

Lash, T.R.

2000-01-01

Even though not all the world's nations have developed a nuclear power industry, nuclear safety is unquestionably an international issue. Perhaps the most compelling proof is the 1986 accident at Chornobyl nuclear power plant in what is now Ukraine. The U.S. Department of Energy conducts a comprehensive, cooperative effort to reduce risks at Soviet-designed nuclear power plants. In the host countries : Armenia, Ukraine, Russia, Bulgaria, the Czech Republic, Hungary, Lithuania, Slovakia, and Kazakhstan joint projects are correcting major safety deficiencies and establishing nuclear safety infrastructures that will be self-sustaining.The U.S. effort has six primary goals: 1. Operational Safety - Implement the basic elements of operational safety consistent with internationally accepted practices. 2. Training - Improve operator training to internationally accepted standards. 3. Safety Maintenance - Help establish technically effective maintenance programs that can ensure the reliability of safety-related equipment. 4. Safety Systems - Implement safety system improvements consistent with remaining plant lifetimes. 5. Safety Evaluations - Transfer the capability to conduct in-depth plant safety evaluations using internationally accepted methods. 6. Legal and Regulatory Capabilities - Facilitate host-country implementation of necessary laws and regulatory policies consistent with their international treaty obligations governing the safe use of nuclear power

EPB standard EN ISO 52016: calculation of the building’s energy needs for heating and cooling, internal temperatures and heating and cooling load

NARCIS (Netherlands)

Dijk, H.A.L. van; Spiekman, M.E.; Hoes-van Oeffelen, E.C.M.

2016-01-01

EN ISO 52016-1 presents a coherent set of calculation methods at different levels of detail, for the (sensible) energy needs for the space heating and cooling and (latent) energy needs (de)humidification of a building and/or internal temperatures and heating and/or cooling loads, including the

A study by internal friction of defects produced in iron and nickel irradiated at very low temperatures; Etude au moyen du frottement interne des defauts crees par irradiation a tres basse temperature dans le fer et le nickel

Energy Technology Data Exchange (ETDEWEB)

Keating-Hart, G de [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1969-07-01

This work represents a contribution to the study of point defects in metals. After a brief review of the theory of internal friction we will discuss some technical innovations aimed at increasing the flexibility of the apparatus at our disposal. These innovations have allowed us to extend our range of measurements down to 20 deg. K. We will then discuss our experimental results. Firstly, we describe preliminary experiments on electron irradiated iron and the evidence for a laminar structure. Secondly, we present and account of the first measurements on nickel after neutron irradiation at 27 deg. K. We will compare the results with those obtained by other methods in this laboratory. Essentially we have observed transitory peaks at low temperature due to close Frenkel pairs and we have noticed the absence of a peak which would correspond to the magnetic after effect band of stage I{sub E}. An attempt is made to explain the disappearance of the observed peaks upon the application of an internal saturating magnetic field. (author) [French] Ce memoire constitue une contribution a l'etude des defauts ponctuels dans les metaux. Apres un bref apercu theorique sur le frottement interne, nous presenterons quelques realisations techniques destinees a accroitre les possibilites des instruments qui nous ont ete confies. Ces dernieres nous ont permis d'etendre la gamme des mesures jusqu'a 20 deg. K. Nous parlerons ensuite de nos resultats experimentaux. En premier lieu, ceux obtenus au cours de premieres experiences, sur le fer irradie aux electrons mettent en evidence des structures de laminage. En second lieu, nous exposerons les premieres mesures realisees sur du nickel irradie aux neutrons; nous comparerons ces resultats avec ceux obtenus par d'autres moyens experimentaux dans le laboratoire. Nous avons observe essentiellement des pics fugitifs a basse temperature dus aux paires proches de Frenckel et nous avons constate l'absence d'un pic correspondant a la bande de tramage

Swimming Safely (A Cup of Health with CDC)

Centers for Disease Control (CDC) Podcasts

In the summertime, families will be flocking to pools for relaxation and relief from the heat. A few simple precautions can help ensure a safe day in the water. In this podcast, Michele Hlavsa discusses ways to stay safe at the pool.

How safe are nuclear plants? How safe should they be?

International Nuclear Information System (INIS)

Kouts, H.

1988-01-01

It has become customary to think about safety of nuclear plants in terms of risk as defined by the WASH-1400 study that some of the implications for the non-specialist escape our attention. Yet it is known that a rational program to understand safety, to identify unsafe events, and to use this kind of information or analysis to improve safety, requires us to use the methods of quantitative risk assessment. How this process can be made more understandable to a broader group of nontechnical people and how can a wider acceptance of the results of the process be developed have been questions under study and are addressed in this report. These are questions that have been struggled with for some time in the world of nuclear plant safety. The Nuclear Regulatory Commission examined them for several years as it moved toward developing a position on safety goals for nuclear plants, a requirement that had been assigned it by Congress. Opinion was sought from a broad spectrum of individuals, within the field of nuclear power and outside it, on the topic that was popularly called, ''How safe is safe enough?'' Views were solicited on the answer to the question and also on the way the answer should be framed when it was adopted. This report discusses the public policy and its implementation

Ergonomics: safe patient handling and mobility.

Science.gov (United States)

Hallmark, Beth; Mechan, Patricia; Shores, Lynne

2015-03-01

This article reviews and investigates the issues surrounding ergonomics, with a specific focus on safe patient handling and mobility. The health care worker of today faces many challenges, one of which is related to the safety of patients. Safe patient handling and mobility is on the forefront of the movement to improve patient safety. This article reviews the risks associated with patient handling and mobility, and informs the reader of current evidence-based practice relevant to this area of care. Copyright © 2015 Elsevier Inc. All rights reserved.

Extended Reconstructed Sea Surface Temperature (ERSST)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Extended Reconstructed Sea Surface Temperature (ERSST) dataset is a global monthly sea surface temperature analysis derived from the International Comprehensive...

[Food poisoning--importance of international perspective].

Science.gov (United States)

Nishibuchi, Mitsuaki

2012-08-01

It is important to obtain the information on food security in the countries other than Japan since more than 60 % of the food consumed come from these countries. Food security is now considered as a global issue. A global trend persuading us to provide safe food to humans is based on the concept of human security development associated with a sense of human mission to sustain one's life. Another global tendency pushing us to secure safety and hygiene of food is driven by the economic pressure coming from the rules in international trade established by Codex Committee under FAO/WHO. In contrast to these trends under globalization requesting safe and hygienic food, food habits based on tradition or religion are maintained locally in various parts of the world. These local habits include eating raw or improperly cooked foods, which may become a risk of being exposed to food poisoning pathogens. This issue may be adequately solved by a risk assessment approach based on the concept of appropriate level of protection (ALOP). Like or not, people in some local areas live in the unhygienic environment where they are unintentionally and frequently exposed to enteric pathogens or immunologically cross-reacting microorganisms through which they may acquire specific immunity to the pathogens and escape from infection by the pathogens. There are therefore many areas in the world where people understand the necessity to provide safe food at the international level (globalization) but actually consume food in varying hygienic conditions from area to area due in part to traditional food habits or living environments (localization); we call this situation as glocalization (global+local).

An art report to analyze internal and external research status for the establishment of the safe supply system of the foods for military meal service using ionization energy

International Nuclear Information System (INIS)

Byun, Myung Woo; Lee, Ju Woon; Kim, Jang Ho; Jo, Cheol Hun; Kim, Dong Ho; Lee, You Seok

2003-09-01

Since the risk of food-borne pathogenic diseases such as E. coli O157:H7 and Salmonella always remains in the military meal service system, it is necessary to develop the method to eliminate this problem. According to the preference survey of military meals, it is shown that soldiers preferred the improvement in quality such as tastes and variety to the increase in quantity. For this reason, the supply of diverse foods, improvement of cooking methods, and the complement of meal service facilities are required. The developed countries such as the United States maintain the facilities to control the environmental factors such as temperature, moisture, and oxygen and they develop and use the rapid methods to test the storage times of each category of foods based on the theoretical studies of food storage/preservation/processing and their experimental data. Due to the ordinary sanitation methods are gradually limited all over the world, as new technology for prevention of food-borne diseases and establishment to manufacture wholesome food, a radiation technology is very effective to ensure safe food and preservation/distribution, improve the safety of processed food and its manufacturing processes. And, the military meal service including combat rations furnishes viability, energy, ability for duty, and mental rest to soldiers. Furthermore, it ensures combat capabilities, enhances mobility power of troops, improves combat efficiency, and establishes the military supply system. It is necessary to study irradiation technique in order to establish the safe food supply system for military meal service and eliminate contamination such as food-borne disease for combat crews as an essential element in military power

Be-safe travel, a web-based geographic application to explore safe-route in an area

Science.gov (United States)

Utamima, Amalia; Djunaidy, Arif

2017-08-01

In large cities in developing countries, the various forms of criminality are often found. For instance, the most prominent crimes in Surabaya, Indonesia is 3C, that is theft with violence (curas), theft by weighting (curat), and motor vehicle theft (curanmor). 3C case most often occurs on the highway and residential areas. Therefore, new entrants in an area should be aware of these kind of crimes. Route Planners System or route planning system such as Google Maps only consider the shortest distance in the calculation of the optimal route. The selection of the optimal path in this study not only consider the shortest distance, but also involves other factors, namely the security level. This research considers at the need for an application to recommend the safest road to be passed by the vehicle passengers while drive an area. This research propose Be-Safe Travel, a web-based application using Google API that can be accessed by people who like to drive in an area, but still lack of knowledge of the pathways which are safe from crime. Be-Safe Travel is not only useful for the new entrants, but also useful for delivery courier of valuables goods to go through the safest streets.

Fail-safe computer-based plant protection systems

International Nuclear Information System (INIS)

Keats, A.B.

1983-01-01

A fail-safe mode of operation for computers used in nuclear reactor protection systems was first evolved in the UK for application to a sodium cooled fast reactor. The fail-safe properties of both the hardware and the software were achieved by permanently connecting test signals to some of the multiplexed inputs. This results in an unambiguous data pattern, each time the inputs are sequentially scanned by the multiplexer. The ''test inputs'' simulate transient excursions beyond defined safe limits. The alternating response of the trip algorithms to the ''out-of-limits'' test signals and the normal plant measurements is recognised by hardwired pattern recognition logic external to the computer system. For more general application to plant protection systems, a ''Test Signal Generator'' (TSG) is used to compute and generate test signals derived from prevailing operational conditions. The TSG, from its knowledge of the sensitivity of the trip algorithm to each of the input variables, generates a ''test disturbance'' which is superimposed upon each variable in turn, to simulate a transient excursion beyond the safe limits. The ''tripped'' status yielded by the trip algorithm when using data from a ''disturbed'' input forms part of a pattern determined by the order in which the disturbances are applied to the multiplexer inputs. The data pattern formed by the interleaved test disturbances is again recognised by logic external to the protection system's computers. This fail-safe mode of operation of computer-based protection systems provides a powerful defence against common-mode failure. It also reduces the importance of software verification in the licensing procedure. (author)

Safe handling of radiation sources

International Nuclear Information System (INIS)

Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

2004-01-01

This chapter discussed the subjects related to the safe handling of radiation sources: type of radiation sources, method of use: transport within premises, transport outside premises; Disposal of Gamma Sources

Strategies and challenges for safe injection practice in developing countries.

Science.gov (United States)

Gyawali, Sudesh; Rathore, Devendra Singh; Shankar, P Ravi; Kumar, Kc Vikash