Belt Aligning Revisited

Directory of Open Access Journals (Sweden)

Yurchenko Vadim

2017-01-01

parts of the conveyor, the sides of the belt wear intensively. This results in reducing the life of the belt. The reasons for this phenomenon are well investigated, but the difficulty lies in the fact that they all act simultaneously. The belt misalignment prevention can be carried out in two ways: by minimizing the effect of causes and by aligning the belt. The construction of aligning devices and errors encountered in practice are considered in this paper. Self-aligning roller supports rotational in plan view are recommended as a means of combating the belt misalignment.

Condition-Based Conveyor Belt Replacement Strategy in Lignite Mines with Random Belt Deterioration

Science.gov (United States)

Blazej, Ryszard; Jurdziak, Leszek

2017-12-01

In Polish lignite surface mines, condition-based belt replacement strategies are applied in order to assure profitable refurbishment of worn out belts performed by external firms specializing in belt maintenance. In two of three lignite mines, staff asses belt condition subjectively during visual inspections. Only one mine applies specialized diagnostic device (HRDS) allowing objective magnetic evaluation of belt core condition in order to choose the most profitable moment for the dismantling of worn out belt segments from conveyors and sending them to the maintenance firm which provides their refurbishment. This article describes the advantages of a new diagnostic device called DiagBelt. It was developed at the Faculty of Geoengineering, Mining and Geology, Wroclaw University of Science and Technology. Economic gains from its application are calculated for the lignite mine and for the belt maintenance firm, taking into account random life (durability) of new and reconditioned belts (after the 1st and the 2nd refurbishment). Recursive calculations for following years allow the estimation of the length and costs of replaced, reconditioned and purchased belts on an annual basis, while the use of the Monte Carlo method allows the estimation of their variability caused by random deterioration of belts. Savings are obtained due to better selection of moments (times) for the replacement of belt segments and die to the possibility to qualify worn out belts for refurbishment without the need to remove their covers. In effect, increased belt durability and lowered share of waste belts (which were not qualified for reconditioning) create savings which can quickly cover expenditures on new diagnostic tools and regular belt inspections in the mine.

Regional setting and geochronology of the Late Cretaceous Banatitic Magmatic and Metallogenetic Belt

Science.gov (United States)

Ciobanu, Cristiana L.; Cook, Nigel J.; Stein, Holly

2002-08-01

The 1,500-km-long Banatitic Magmatic and Metallogenetic Belt (BMMB) of Romania, Serbia and Bulgaria is a complex calc-alkaline magmatic arc of Late Cretaceous age. It hosts a variety of magmatic-hydrothermal Cu, Au, Mo, Zn, Pb and Fe deposits, including Europe's only world-class porphyry-copper deposits. Regional metallogeny can be linked to subduction of the Vardar Ocean during the Late Cretaceous, as part of the closure of the Neotethys Ocean that had separated Europe and Africa in the Mesozoic. Porphyry Cu-(Au)-(Mo) and intimately associated epithermal massive sulphides dominate in the central segments of the belt in southernmost Banat (Romania), Serbia and north-west Bulgaria. These districts are the economically most important today, including major active Cu-Au mines at Moldova Nouă in Romania, Majdanpek, Veliki Krivelj and Bor in Serbia, and Elatsite, Assarel and Chelopech in Bulgaria. More numerous (and mostly mined in the past) are Fe, Cu and Zn-Pb skarns, which occur mainly at the two ends of the belt, in Eastern Bulgaria and in Romania. This paper summarises some of the deposit characteristics within the geodynamic framework of terminal Vardar subduction. Heterogeneous terranes of the belt, including the Apuseni Mountains at the western end, are aligned parallel to the Vardar front following continental collision of the Dacia and Tisza blocks. All available geochronological data (numerous K-Ar and some U-Pb and Re-Os ages) are compiled, and are complemented by a new high-precision Re-Os date for the Dognecea skarn deposit, south-west Romania (76.6±0.3 Ma). These data indicate that magmatism extended over at least 25 million years, from about 90 to 65 Ma in each segment of the belt. Within Apuseni Mountains and Banat, where magma emplacement was related to syn-collisional extension in the orogenic belt of Carpathians, ore formation seems to be restricted in time and maybe constrained by a shared tectonic event.

Effectiveness of Ford's belt reminder system in increasing seat belt use

OpenAIRE

Williams, A; Wells, J; Farmer, C

2002-01-01

Objectives: The study investigated the effectiveness in increasing seat belt use of Ford's belt reminder system, a supplementary system that provides intermittent flashing lights and chimes for five minutes if drivers are not belted.

Storm-time radiation belt electron dynamics: Repeatability in the outer radiation belt

Science.gov (United States)

Murphy, K. R.; Mann, I. R.; Rae, J.; Watt, C.; Boyd, A. J.; Turner, D. L.; Claudepierre, S. G.; Baker, D. N.; Spence, H. E.; Reeves, G. D.; Blake, J. B.; Fennell, J. F.

2017-12-01

During intervals of enhanced solar wind driving the outer radiation belt becomes extremely dynamic leading to geomagnetic storms. During these storms the flux of energetic electrons can vary by over 4 orders of magnitude. Despite recent advances in understanding the nature of competing storm-time electron loss and acceleration processes the dynamic behavior of the outer radiation belt remains poorly understood; the outer radiation belt can exhibit either no change, an enhancement, or depletion in radiation belt electrons. Using a new analysis of the total radiation belt electron content, calculated from the Van Allen probes phase space density (PSD), we statistically analyze the time-dependent and global response of the outer radiation belt during storms. We demonstrate that by removing adiabatic effects there is a clear and repeatable sequence of events in storm-time radiation belt electron dynamics. Namely, the relativistic (μ=1000 MeV/G) and ultra-relativistic (μ=4000 MeV/G) electron populations can be separated into two phases; an initial phase dominated by loss followed by a second phase dominated by acceleration. At lower energies, the radiation belt seed population of electrons (μ=150 MeV/G) shows no evidence of loss but rather a net enhancement during storms. Further, we investigate the dependence of electron dynamics as a function of the second adiabatic invariant, K. These results demonstrate a global coherency in the dynamics of the source, relativistic and ultra-relativistic electron populations as function of the second adiabatic invariant K. This analysis demonstrates two key aspects of storm-time radiation belt electron dynamics. First, the radiation belt responds repeatably to solar wind driving during geomagnetic storms. Second, the response of the radiation belt is energy dependent, relativistic electrons behaving differently than lower energy seed electrons. These results have important implications in radiation belt research. In particular

Belt attachment and system

Energy Technology Data Exchange (ETDEWEB)

Schneider, Abraham D.; Davidson, Erick M.

2018-03-06

Disclosed herein is a belt assembly including a flexible belt with an improved belt attachment. The belt attachment includes two crossbars spaced along the length of the belt. The crossbars retain bearings that allow predetermined movement in six degrees of freedom. The crossbars are connected by a rigid body that attaches to the bearings. Implements that are attached to the rigid body are simply supported but restrained in pitching rotation.

Riding the belt

Energy Technology Data Exchange (ETDEWEB)

Potts, A

1998-04-01

Recent developments in conveyor systems have focused on accessories rather than the belt itself. Radio frequency identification (RFID) is a technology using transponders embedded in conveyor belts and this is the latest development at the German firm Contitech. The system described in the articles developed with Moers, features transponders for cooling, controlling and monitoring conveyor belts. Other developments mentioned include a JOKI drum motor featuring a fully integrated gearbox and electric motor enclosed in a steel shell, from Interoll; a new scraper cleaning system from Hosch, new steel cord belting from Fenner, a conveying system for Schleenhain lignite opencast mine by FAM Foerdelantigen Magdeburg; new bearings from Nadella (the sales arm of Intersoll-Rand), an anti-shock belt transfer table from Rosta and new caliper disc brakes from GE Industrial.

Synaptic ribbon. Conveyor belt or safety belt?

Science.gov (United States)

Parsons, T D; Sterling, P

2003-02-06

The synaptic ribbon in neurons that release transmitter via graded potentials has been considered as a conveyor belt that actively moves vesicles toward their release sites. But evidence has accumulated to the contrary, and it now seems plausible that the ribbon serves instead as a safety belt to tether vesicles stably in mutual contact and thus facilitate multivesicular release by compound exocytosis.

Earth's radiation belts

International Nuclear Information System (INIS)

Moslehi Fard, M.

1984-01-01

The theory of trapped particles in a magnetic field of approximated dipole is described completely in the first part. Second part contains experimental results. The mechanism of radiation belt source ''albedo neutrons'' and also types of dissipation mechanism about radiation belt is explained. The trapped protons and electrons by radiation belt is discussed and the life-time of trapped particles are presented. Finally the magnetic fields of Moon, Venus, Mars, and Saturn, measured by passengers Mariner 4,10 and pioneer 10,11 are indicated. The experimental and theoretical results for the explanation of trapped plasma around the earth which is looked like two internal and external belt have almost good correspondence

Dynamics Analysis and Modeling of Rubber Belt in Large Mine Belt Conveyors

OpenAIRE

Gao Yang

2014-01-01

Rubber belt not only is one of the key components of belt conveyor, but also affects the overall performance of the core part. Research on dynamics analysis of large conveyor not only helps to improve the reliability and design level, but also can guide the rational selection of conveyor safety factor, and effectively reduce the cost of the conveyor belt. Based on unique viscoelastic properties of belt conveyor, it was simplified as one-dimensional viscoelastic rod in this study, and then a d...

Belt conveyor apparatus

Science.gov (United States)

Oakley, David J.; Bogart, Rex L.

1987-01-01

A belt conveyor apparatus according to this invention defines a conveyance path including a first pulley and at least a second pulley. An endless belt member is adapted for continuous travel about the pulleys and comprises a lower portion which engages the pulleys and an integral upper portion adapted to receive objects therein at a first location on said conveyance path and transport the objects to a second location for discharge. The upper belt portion includes an opposed pair of longitudinally disposed crest-like members, biased towards each other in a substantially abutting relationship. The crest-like members define therebetween a continuous, normally biased closed, channel along the upper belt portion. Means are disposed at the first and second locations and operatively associated with the belt member for urging the normally biased together crest-like members apart in order to provide access to the continuous channel whereby objects can be received into, or discharged from the channel. Motors are in communication with the conveyance path for effecting the travel of the endless belt member about the conveyance path. The conveyance path can be configured to include travel through two or more elevations and one or more directional changes in order to convey objects above, below and/or around existing structures.

Analysis of stress distribution of timing belts by FEM; Yugen yosoho ni yoru timing belt oryoku kaiseki (belt code oryoku bunpu kaiseki hokoku)

Energy Technology Data Exchange (ETDEWEB)

Furukawa, Y; Tomono, K; Takahashi, H; Uchida, T [Honda R and D Co. Ltd., Tokyo (Japan)

1997-10-01

A model of the belt analyzed by-ABAQUS (: a general nonlinear finite element program) successfully confirmed the mechanism that generates the belt cord stress. A quite good agreement between experimental and computed results for the stress distribution of the belt cord. It is found that maximum stress of the cords occurs near the root of the tooth by calculation, where the belt cords break off. 3 refs., 9 figs.

Checklist of ichthyofauna of Madampa-Lake sanctuary in Ambalangoda, Southwest Sri Lanka

Directory of Open Access Journals (Sweden)

Hareschandra Bandula Jayaneththi

2017-06-01

Full Text Available Coastal lagoons provide unique services for many kinds of aquatic and semi aquatic organisms. Madampa-Lake is a brackish water lagoon containing a dynamic mangrove ecosystem complex with extraordinary genetic diversity, which is located in the southwest coastal belt near Ambalangoda city, Galle District. Very little literature is available on the Madampa-Lake’s fish and almost none of them have been published. A preliminary assessment on vertebrates and butterfly fauna was carried out during April 2009 to August 2010, and this article covers ichthyofaunal phase of the survey. Ichthyofauna diversity of Madampa is a combination of salt water (sea, brackish water and fresh water fish and their different life stages. During this study, a total of 49 species (33 families were recorded, and this included two endemics and five alien species.

Factors controlling mud accumulation in the Heuksan mud belt off southwestern Korea

Science.gov (United States)

Chang, Tae Soo; Ha, Hun Jun; Chun, Seung Soo

2015-12-01

The Heuksan mud belt (hereafter HMB) is 20~50 km wide, ~200 km long, and ~50 m thick, having accumulated in the course of the Holocene transgression on the tide-dominated epicontinental shelf southwest of Korea. The internal architecture of the HMB is characterized by offshore prograding clinoforms. Of particular interest are the depositional processes responsible for this anomalously thick mud accumulation within a relatively short period of time. Tidal currents are important in the dispersal of mud in the HMB, although these alone cannot explain such an enormous mud deposit. In order to understand the formative processes of the HMB, a detailed sedimentary facies analysis, including high-resolution grain-size measurements, has been conducted on more than 30 short cores and three long drill cores recovered from the mud belt. Five major mud facies were identified. Of these, mud sequences showing a thickening-thinning trend of alternating silt and clay laminae suggestive of a tidal origin occur dominantly at inner to mid shelf locations. By contrast, internally structureless muds with sharp bases and no bioturbation, which are interpreted of representing fluid-mud deposits, are widespread at mid to outer shelf locations. Wave-generated mud ripples and storm beds on the inner shelf suggest that storm waves in winter resuspend previously deposited mud to form near-bed fluid-mud suspensions with resulting gravity-driven mud transport across the low-gradient outer shelf. This previously not recognized process is probably a major factor controlling depositional processes on the giant mud belt, enabling rapid accumulation and offshore progradation even during transgression, i.e., at times of sea-level rise.

Belt drive construction improvement

Directory of Open Access Journals (Sweden)

I.Yu. Khomenko

2012-08-01

Full Text Available The possibility of the traction capacity increase of the belt drive TRK is examined. This was done for the purpose of air conditioning system of passenger car with double-generator system energy supplying. Belts XPC (made by the German firm «Continental ContiTech» testing were conducted. The results confirmed the possibility of their usage in order to improve belt drive TRK characteristics.

Continuous Mass Measurement on Conveyor Belt

Science.gov (United States)

Tomobe, Yuki; Tasaki, Ryosuke; Yamazaki, Takanori; Ohnishi, Hideo; Kobayashi, Masaaki; Kurosu, Shigeru

The continuous mass measurement of packages on a conveyor belt will become greatly important. In the mass measurement, the sequence of products is generally random. An interesting possibility of raising throughput of the conveyor line without increasing the conveyor belt speed is offered by the use of two or three conveyor belt scales (called a multi-stage conveyor belt scale). The multi-stage conveyor belt scale can be created which will adjust the conveyor belt length to the product length. The conveyor belt scale usually has maximum capacities of less than 80kg and 140cm, and achieves measuring rates of more than 150 packages per minute and more. The output signals from the conveyor belt scale are always contaminated with noises due to vibrations of the conveyor and the product to be measured in motion. In this paper an employed digital filter is of Finite Impulse Response (FIR) type designed under the consideration on the dynamics of the conveyor system. The experimental results on the conveyor belt scale suggest that the filtering algorithms are effective enough to practical applications to some extent.

Equilibria and Free Vibration of a Two-Pulley Belt-Driven System with Belt Bending Stiffness

Directory of Open Access Journals (Sweden)

Jieyu Ding

2014-01-01

Full Text Available Nonlinear equilibrium curvatures and free vibration characteristics of a two-pulley belt-driven system with belt bending stiffness and a one-way clutch are investigated. With nonlinear dynamical tension, the transverse vibrations of the translating belt spans and the rotation motions of the pulleys and the accessory shaft are coupled. Therefore, nonlinear piecewise discrete-continuous governing equations are established. Considering the bending stiffness of the translating belt spans, the belt spans are modeled as axially moving beams. The pattern of equilibria is a nontrivial solution. Furthermore, the nontrivial equilibriums of the dynamical system are numerically determined by using two different approaches. The governing equations of the vibration near the equilibrium solutions are derived by introducing a coordinate transform. The natural frequencies of the dynamical systems are studied by using the Galerkin method with various truncations and the differential and integral quadrature methods. Moreover, the convergence of the Galerkin truncation is investigated. Numerical results reveal that the study needs 16 terms after truncation in order to determine the free vibration characteristics of the pulley-belt system with the belt bending stiffness. Furthermore, the first five natural frequencies are very sensitive to the bending stiffness of the translating belt.

Influence of pre-existing basement faults on the structural evolution of the Zagros Simply Folded belt: 3D numerical modelling

Science.gov (United States)

Ruh, Jonas B.; Gerya, Taras

2015-04-01

The Simply Folded Belt of the Zagros orogen is characterized by elongated fold trains symptomatically defining the geomorphology along this mountain range. The Zagros orogen results from the collision of the Arabian and the Eurasian plates. The Simply Folded Belt is located southwest of the Zagros suture zone. An up to 2 km thick salt horizon below the sedimentary sequence enables mechanical and structural detachment from the underlying Arabian basement. Nevertheless, deformation within the basement influences the structural evolution of the Simply Folded Belt. It has been shown that thrusts in form of reactivated normal faults can trigger out-of-sequence deformation within the sedimentary stratigraphy. Furthermore, deeply rooted strike-slip faults, such as the Kazerun faults between the Fars zone in the southeast and the Dezful embayment and the Izeh zone, are largely dispersing into the overlying stratigraphy, strongly influencing the tectonic evolution and mechanical behaviour. The aim of this study is to reveal the influence of basement thrusts and strike-slip faults on the structural evolution of the Simply Folded Belt depending on the occurrence of intercrustal weak horizons (Hormuz salt) and the rheology and thermal structure of the basement. Therefore, we present high-resolution 3D thermo-mechnical models with pre-existing, inversively reactivated normal faults or strike-slip faults within the basement. Numerical models are based on finite difference, marker-in-cell technique with (power-law) visco-plastic rheology accounting for brittle deformation. Preliminary results show that deep tectonic structures present in the basement may have crucial effects on the morphology and evolution of a fold-and-thrust belt above a major detachment horizon.

Dynamics Analysis and Modeling of Rubber Belt in Large Mine Belt Conveyors

Directory of Open Access Journals (Sweden)

Gao Yang

2014-10-01

Full Text Available Rubber belt not only is one of the key components of belt conveyor, but also affects the overall performance of the core part. Research on dynamics analysis of large conveyor not only helps to improve the reliability and design level, but also can guide the rational selection of conveyor safety factor, and effectively reduce the cost of the conveyor belt. Based on unique viscoelastic properties of belt conveyor, it was simplified as one-dimensional viscoelastic rod in this study, and then a discrete element model of conveyor systems was established. The kinetic equations of each discrete unit was derived using kinetic energy, potential energy of driving segment, bearing segment and return segment and equation of energy dissipation and Lagrange equation. Based on Wilson-q algorithm, the kinetic equation of DT1307-type ST2000's conveyor belt was solved by using Matlab to write computer programs. Research on the change rule of conveyor displacement, velocity, acceleration and dynamic tension during the boot process revealed the working mechanism of nonlinear viscoelastic, which lay the theoretical foundation for dynamic performance optimization of large belt conveyor. The calculation results were used to optimize design and analysis of conveyor system, the result showed that it could reduce the driven tension peaks about 12 %, save 5 % of overall manufacturing cost, which bring considerable profits for enterprises.

Lap belt injuries in children.

LENUS (Irish Health Repository)

McGrath, N

2010-07-01

The use of adult seat belts without booster seats in young children may lead to severe abdominal, lumbar or cervical spine and head and neck injuries. We describe four characteristic cases of lap belt injuries presenting to a tertiary children\\'s hospital over the past year in addition to a review of the current literature. These four cases of spinal cord injury, resulting in significant long-term morbidity in the two survivors and death in one child, arose as a result of lap belt injury. These complex injuries are caused by rapid deceleration characteristic of high impact crashes, resulting in sudden flexion of the upper body around the fixed lap belt, and consequent compression of the abdominal viscera between the lap belt and spine. This report highlights the dangers of using lap belts only without shoulder straps. Age-appropriate child restraint in cars will prevent these injuries.

Belt technology stretches conveyors' coverage

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-15

With China the leading growth engine in the conveyor market, leading belt manufacturers are establishing local manufacturing plants to boost their presence. Fenner is planning to almost triple production capacity over the next three years, with a third of its investment in China. Shanxi-Phoenix Conveyor Belt Systems is a joint venture between Phoenix Conveyor Belt Systems GmbH, now part of ContiTech Ag, and its Chinese partners Lu An Mining Group Co. Ltd. and Jingcheng Anthracite Group Co. Ltd. It manufacturers steel cable belts, PVC and multi-ply belts for coal mines and power plants. Recent belt designs by FennerEurope and Metso Minerals are reported. 2 photos.

Vertical displacement during late-collisional escape tectonics (Brasiliano Orogeny) in the Ribeira Belt, São Paulo State, Brazil

Science.gov (United States)

Hackspacher, P. C.; Godoy, A. M.

1999-07-01

During the Brasiliano-Pan-African Orogeny, West Gondwana formed by collisional processes around the São Francisco-Congo Craton. The Ribeira belt, in southeastern Brazil, resulted from northwestward collision (650-600 Ma), followed by large-scale northeast-southwest dextral strike-slip shear movements related to late-collisional escape tectonics ( ca 600 Ma). In São Paulo State, three groups, also interpreted as terranes, are recognised in the Ribeira Belt, the Embu, Itapira and São Roque Groups. The Embu and Itapira Groups are formed of sillimanite-gneisses, schists and migmatites intruded by Neoproterozoic calc-alkaline granitoids, all thrusted northwestward. The São Roque Group is composed of metasediments and metavolcanics in greenschist-facies. Its deformation indicates a transpressional regime associated with tectonic escape. Sub-alkaline granites were emplaced in shallow levels during this regime. Microstructural studies along the Itu, Moreiras and Taxaquara Shear Zones demonstrate the coexistence of horizontal and vertical displacement components during the transpressional regime. The vertical component is regarded as responsible for the lateral juxtaposition of different crustal levels.

Drivers' attitudes toward front or rear child passenger belt use and seat belt reminders at these seating positions.

Science.gov (United States)

Kidd, David G; McCartt, Anne T

2014-01-01

Passengers, especially those in rear seating positions, use seat belts less frequently than drivers. In-vehicle technology can inform drivers when their passengers are unbuckled and encourage passengers to use belts. The current study collected information about drivers' attitudes toward passenger belt use and belt reminders for front passengers and children in back seats. A national telephone survey of 1218 people 18 and older was conducted, of which 477 respondents were drivers who transport a front seat passenger at least once a week and 254 were drivers who transport an 8- to 15-year-old child in the back seat. Respondents were asked about their attitudes toward belt use by their front passengers or rear child passengers and preferences for different passenger belt reminder features. Ninety percent of drivers who regularly transport front seat passengers said that the passengers always use seat belts. Reported belt use was even higher among 8- to 15-year-old children in the back seat (97%). Among the drivers whose children do not always buckle up, about half said their child unbuckled the belt during the trip. Almost every full-time belt use driver (96%) would encourage front passengers to buckle up if not belted, compared to 57 percent of part-time belt users and nonusers. In contrast, nearly every driver who transports children in the back seat would encourage their belt use, regardless of the driver's belt use habits. Most drivers who transport front passengers wanted passenger belt reminders to encourage passengers to buckle up. Most of these drivers wanted a chime/buzzer or warning light or text display and wanted the reminder to last indefinitely. Most drivers who transport child passengers in the rear seat wanted the vehicle to indicate whether child passengers are unbuckled. A large majority of these drivers wanted notifications via a visual diagram of seating positions and belt use, a chime/buzzer, and a warning light or text display. These drivers

Belt conveyors for bulk materials. 6th ed.

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The 16 chapters are entitled: Belt conveyor general applications economics; Design considerations; Characteristics and conveyability of bulk materials; Capacities, belt widths and speeds; Belt conveyor idlers; Belt tension and power engineering; Belt selection; Pulleys and shafts; Curves; Steep angle conveying; Belt cleaners and accessories; Transfer points; Conveyor motor drives and controls; Operation, maintenance and safety; Belt takeups; and Emerging technologies. 6 apps.

Belt conveying of minerals

Energy Technology Data Exchange (ETDEWEB)

Stace, L.R.; Yardley, E.D. [University of Nottingham, Nottingham (United Kingdom). School of Civil Engineering

2008-02-15

A discussion of the history and economics of conveyor applications sets the scene. Conveyor design is investigated in detail, covering power requirements, belt tensioning, and hardware. Principles regarding construction and joining of belts are outlined and a helpful and practical overview of relevant standards, belt test methods, and issues surrounding standardisation is given. Conveyor belt systems can represent a significant operational hazard, so the authors have set out to highlight the important area of safety, with consideration given to fire/electrical resistance, as well as the interface between personnel and conveyor systems - including nip points and operational issues such as man-riding. Selected case studies illustrate some practical aspects of installation and operation, at Selby mine in the UK and Prosper-Haniel Colliery in Germany and others. 3 apps.

Deformation from the 1989 Loma Prieta earthquake near the southwest margin of the Santa Clara Valley, California

Science.gov (United States)

Schmidt, Kevin M.; Ellen, Stephen D.; Peterson, David M.

2014-01-01

Damage to pavement and near-surface utility pipes, caused by the 17 October 1989, Loma Prieta earthquake, provides evidence for ground deformation in a 663 km2 area near the southwest margin of the Santa Clara Valley, California (USA). A total of 1427 damage sites, collected from more than 30 sources, are concentrated in four zones, three of which lie near previously mapped faults. In one of these zones, the channel lining of Los Gatos Creek, a 2-km-long concrete strip trending perpendicular to regional geologic structure, was broken by thrusts that were concentrated in two belts, each several tens of meters wide, separated by more than 300 m of relatively undeformed concrete.

Roll-front uranium occurrences of the South Texas Mineral Belt: Development of a database for mineral potential modelling and quantitative resource assessment

International Nuclear Information System (INIS)

Mihalasky, M.

2014-01-01

The South Texas Mineral Belt in the United States is a broad curvilinear region of marginal-marine roll-front sandstone uranium occurrences. Located ~130 km inland, the belt parallels the Gulf of Mexico coastline and extends from southeast Texas to Mexico. It trends northeast-southwest and is about 400 km long and 10-50 km wide as delineated by alignments and clusters of occurrences, but ~100 km wide if outlying occurrences are included. The occurrences are hosted in coastal plain sediments and rocks of Tertiary age that dip gently towards the Gulf. These include the Lower Eocene Wilcox Group, Middle Eocene Claiborne Group, Upper Eocene Jackson Group, Upper Oligocene–Miocene Catahoula Tuff, Lower Miocene Oakville Sandstone, and Pliocene Goliad Sand. Older sequences are mixed fluvial-beach facies, whereas younger are dominantly fluvial. Occurrence distribution is controlled by host unit strike and dip, and permeable sequences therein, and by a combination of growth faults and locations of reductants.

VERO cells harbor a poly-ADP-ribose belt partnering their epithelial adhesion belt

Directory of Open Access Journals (Sweden)

Laura Lafon-Hughes

2014-10-01

Full Text Available Poly-ADP-ribose (PAR is a polymer of up to 400 ADP-ribose units synthesized by poly-ADP-ribose-polymerases (PARPs and degraded by poly-ADP-ribose-glycohydrolase (PARG. Nuclear PAR modulates chromatin compaction, affecting nuclear functions (gene expression, DNA repair. Diverse defined PARP cytoplasmic allocation patterns contrast with the yet still imprecise PAR distribution and still unclear functions. Based on previous evidence from other models, we hypothesized that PAR could be present in epithelial cells where cadherin-based adherens junctions are linked with the actin cytoskeleton (constituting the adhesion belt. In the present work, we have examined through immunofluorescence and confocal microscopy, the subcellular localization of PAR in an epithelial monkey kidney cell line (VERO. PAR was distinguished colocalizing with actin and vinculin in the epithelial belt, a location that has not been previously reported. Actin filaments disruption with cytochalasin D was paralleled by PAR belt disruption. Conversely, PARP inhibitors 3-aminobenzamide, PJ34 or XAV 939, affected PAR belt synthesis, actin distribution, cell shape and adhesion. Extracellular calcium chelation displayed similar effects. Our results demonstrate the existence of PAR in a novel subcellular localization. An initial interpretation of all the available evidence points towards TNKS-1 as the most probable PAR belt architect, although TNKS-2 involvement cannot be discarded. Forthcoming research will test this hypothesis as well as explore the existence of the PAR belt in other epithelial cells and deepen into its functional implications.

Pelvic belt effects on sacroiliac joint ligaments: a computational approach to understand therapeutic effects of pelvic belts.

Science.gov (United States)

Sichting, Freddy; Rossol, Jerome; Soisson, Odette; Klima, Stefan; Milani, Thomas; Hammer, Niels

2014-01-01

The sacroiliac joint is a widely described source of low back pain. Therapeutic approaches to relieve pain include the application of pelvic belts. However, the effects of pelvic belts on sacroiliac joint ligaments as potential pain generators are mostly unknown. The aim of our study was to analyze the influence of pelvic belts on ligament load by means of a computer model. Experimental computer study using a finite element method. A computer model of the human pelvis was created, comprising bones, ligaments, and cartilage. Detailed geometries, material properties of ligaments, and in-vivo pressure distribution patterns of a pelvic belt were implemented. The effects of pelvic belts on ligament strain were computed in the double-leg stance. Pelvic belts increase sacroiliac joint motion around the sagittal axis but decrease motion around the transverse axis. With pelvic belt application, most of the strained sacroiliac joint ligaments were relieved, especially the sacrospinous, sacrotuberous, and the interosseous sacroiliac ligaments. Sacroiliac joint motion and ligament strains were minute. These results agree with validation data from other studies. Assigning homogenous and linear material properties and excluding muscle forces are clear simplifications of the complex reality. Pelvic belts alter sacroiliac joint motion and provide partial relief of ligament strain that is subjectively marked, although minimal in absolute terms. These findings confirm theories that besides being mechanical stabilizers, the sacroiliac joint ligaments are likely involved in neuromuscular feedback mechanisms. The results from our computer model help with unraveling the therapeutic mechanisms of pelvic belts.

30 CFR 57.4503 - Conveyor belt slippage.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Conveyor belt slippage. 57.4503 Section 57.4503... Control Installation/construction/maintenance § 57.4503 Conveyor belt slippage. (a) Surface belt conveyors...) Underground belt conveyors shall be equipped with a detection system capable of automatically stopping the...

Investigation of a new type charging belt

International Nuclear Information System (INIS)

Jones, N.L.

1994-01-01

There are many desirable characteristics for an electrostatic accelerator charging belt. An attempt has been made to find a belt that improves on these properties over the stock belt. Results of the search, procurement, and 1,500 hours of operational experience with a substantially different belt are reported

Belt for picking up liquids

Energy Technology Data Exchange (ETDEWEB)

Sewell, R B.H.; Nelson, S P

1973-05-18

This belt for picking up liquids consists of a layer of strong material, e.g., coarse cloth, sewed on at least one layer of absorbing material, e.g., sponge cloth, the stitching being disposed along chevrons with their apexes along the central axis of the belt; the edges do not contain any other marks. This arrangement facilitates the expulsion of the absorbed liquid when the belt passes between compression rollers.

30 CFR 56.4503 - Conveyor belt slippage.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Conveyor belt slippage. 56.4503 Section 56.4503... Control Installation/construction/maintenance § 56.4503 Conveyor belt slippage. Belt conveyors within... shall attend the belt at the drive pulley when it is necessary to operate the conveyor while temporarily...

14 CFR 27.1413 - Safety belts.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Safety belts. 27.1413 Section 27.1413 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Equipment Safety Equipment § 27.1413 Safety belts. Each safety belt...

Persistence of Salmonella on egg conveyor belts is dependent on the belt type but not on the rdar morphotype.

Science.gov (United States)

Stocki, S L; Annett, C B; Sibley, C D; McLaws, M; Checkley, S L; Singh, N; Surette, M G; White, A P

2007-11-01

Commercial caged layer flocks in Alberta, Canada, are commonly monitored for Salmonella enterica serovar Enteritidis (SE) and S. enterica serovar Typhimurium (ST) by environmental sampling. In one recent case, a SE strain isolated from the egg conveyor belt was a source of persistent infection for the flock. This study was undertaken to examine Salmonella colonization on egg conveyor belts and to determine whether the rdar morphotype, a conserved physiology associated with aggregation and long-term survival, contributed to persistence. Four woven belts constructed of natural or nonnatural fibers and a 1-piece belt made of vinyl were tested with rdar-positive ST and SE strains and a rdar-negative ST DeltaagfD reference strain. The type of egg belt was the most important factor influencing Salmonella colonization and persistence. The vinyl belt, with the least surface area available for colonization, had the fewest Salmonella remaining after washing and disinfection, whereas the hemp-plastic belt, with the greatest surface area, had the most Salmonella remaining. Real-time gene expression indicated that the rdar morphotype was involved in colonizing the egg belt pieces; however, it was not essential for persistence. In addition, rdar-positive and rdar-negative strains were equally similarly to disinfection on the egg belt pieces. The results indicate that Salmonella can persist on a variety of egg belts by mechanisms other than the rdar morphotype, and that using egg conveyer belts with reduced surface area for bacterial colonization can lessen contamination problems.

Granulite belts of Central India with special reference to the Bhopalpatnam Granulite Belt: Significance in crustal evolution and implications for Columbia supercontinent

Science.gov (United States)

Vansutre, Sandeep; Hari, K. R.

2010-11-01

The Central Indian collage incorporates the following major granulite belts: (1) the Balaghat-Bhandara Granulite Belt (BBG), (2) the Ramakona-Katangi Granulite Belt (RKG), (3) the Chhatuabhavna Granulite (CBG) of Bilaspur-Raigarh Belt, (4) the Makrohar Granulite Belt (MGB) of Mahakoshal supracrustals, (5) the Kondagaon Granulite Belt (KGGB), (6) the Bhopalpatnam Granulite Belt (BGB), (7) the Konta Granulite Belt (KTGB) and (8) the Karimnagar Granulite Belt (KNGB) of the East Dharwar Craton (EDC). We briefly synthesize the general geologic, petrologic and geochronologic features of these belts and explain the Precambrian crustal evolution in Central India. On the basis of the available data, a collisional relationship between Bastar craton and the EDC during the Paleo-Mesoproterozoic is reiterated as proposed by the earlier workers. The tectonic evolution of only few of the orogenic belts (BGB in particular) of Central India is related to Columbia.

Observed use of automatic seat belts in 1987 cars.

Science.gov (United States)

Williams, A F; Wells, J K; Lund, A K; Teed, N

1989-10-01

Usage of the automatic belt systems supplied by six large-volume automobile manufacturers to meet the federal requirements for automatic restraints were observed in suburban Washington, D.C., Chicago, Los Angeles, and Philadelphia. The different belt systems studied were: Ford and Toyota (motorized, nondetachable automatic shoulder belt), Nissan (motorized, detachable shoulder belt), VW and Chrysler (nonmotorized, detachable shoulder belt), and GM (nonmotorized detachable lap and shoulder belt). Use of automatic belts was significantly greater than manual belt use in otherwise comparable late-model cars for all manufacturers except Chrysler; in Chrysler cars, automatic belt use was significantly lower than manual belt use. The automatic shoulder belts provided by Ford, Nissan, Toyota, and VW increased use rates to about 90%. Because use rates were lower in Ford cars with manual belts, their increase was greater. GM cars had the smallest increase in use rates; however, lap belt use was highest in GM cars. The other manufacturers supply knee bolsters to supplement shoulder belt protection; all--except VW--also provide manual lap belts, which were used by about half of those who used the automatic shoulder belt. The results indicate that some manufacturers have been more successful than others in providing automatic belt systems that result in high use that, in turn, will mean fewer deaths and injuries in those cars.

14 CFR 31.63 - Safety belts.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Safety belts. 31.63 Section 31.63 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: MANNED FREE BALLOONS Design Construction § 31.63 Safety belts. (a) There must be a safety belt...

30 CFR 77.1107 - Belt conveyors.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Belt conveyors. 77.1107 Section 77.1107 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY... § 77.1107 Belt conveyors. Belt conveyors in locations where fire would create a hazard to personnel...

46 CFR 169.723 - Safety belts.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Safety belts. 169.723 Section 169.723 Shipping COAST... Control, Miscellaneous Systems, and Equipment § 169.723 Safety belts. Each vessel must carry a harness type safety belt conforming to Offshore Racing Council (ORC) standards for each person on watch or...

Plant trial of an under-belt capacitance and gamma-ray backscatter gauge for on-belt determination of moisture in coal

International Nuclear Information System (INIS)

Cutmore, N.G.; Rafter, P.T.; Abernethy, D.A.; Millen, M.J.

1989-01-01

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance, determined using an under-belt capacitance sensor in which a fringing electric field interrogates a layer of coal on the conveyor belt directly about the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal. A plant trial of the technique was conducted at Stockton Borehole Colliery, NSW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7-14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the on-belt gauge. 6 refs., 6 figs., 3 tabs

Heavy metal deposition fluxes affecting an Atlantic coastal area in the southwest of Spain

Science.gov (United States)

Castillo, Sonia; de la Rosa, Jesús D.; Sánchez de la Campa, Ana M.; González-Castanedo, Yolanda; Fernández-Camacho, Rocío

2013-10-01

The present study seeks to estimate the impact of industrial emissions and harbour activities on total atmospheric deposition in an Atlantic coastal area in the southwest of the Iberian Peninsula. Three large industrial estates and a busy harbour have a notable influence on air quality in the city of Huelva and the surrounding area. The study is based on a geochemical characterization of trace elements deposited (soluble and insoluble fractions) in samples collected at a rate of 15 days/sample from June 2008 to May 2011 in three sampling sites, one in the principal industrial belt, another in the city of Huelva, and the last, 56 km outside Huelva city in an area of high ecological interest. The industrial emissions emitted by the Huelva industrial belt exert a notable influence on atmospheric deposition. Major deposition fluxes were registered for Fe, Cu, V, Ni, P, Pb, As, Sn, Sb, Se and Bi, principally in the insoluble fraction, derived from industrial funnel emissions and from harbour activities. Metals such as Mn, Ni, Cu and Zn, and elements such as P also have a significant presence in the soluble fraction converting them into potentially bio-available nutrients for the living organism in the ocean. A principal component analysis certifies three common emissions sources in the area: 1) a mineral factor composed mainly of elements derived from silicate minerals mixed with certain anthropogenic species (Mg, K, Sr, Na, Al, Ba, LREE, Li, Mn, HREE, Ti, Fe, Se, V, SO-, Ni, Ca and P); 2) an industrial factor composed of the same trace elements in the three areas (Sb, Mo, Bi, As, Pb, Sn and Cd) thus confirming the impact of the emissions from the Huelva industrial belt on remote areas; and 3) a marine factor composed of Na, Cl, Mg and SO.

36 CFR 4.15 - Safety belts.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Safety belts. 4.15 Section 4... TRAFFIC SAFETY § 4.15 Safety belts. (a) Each operator and passenger occupying any seating position of a motor vehicle in a park area will have the safety belt or child restraint system properly fastened at...

Complex fold and thrust belt structural styles: Examples from the Greater Juha area of the Papuan Fold and Thrust Belt, Papua New Guinea

Science.gov (United States)

Mahoney, Luke; Hill, Kevin; McLaren, Sandra; Hanani, Amanda

2017-07-01

The remote and inhospitable Papuan Fold Belt in Papua New Guinea is one of the youngest yet least well-documented fold and thrust belts on Earth. Within the frontal Greater Juha area we have carried out >100 km of geological traverses and associated analyses that have added significantly to the contemporary geological and geophysical dataset. Our structural analysis provides evidence of major inversion, detachment and triangle zone faults within the uplifted Eastern Muller Ranges. We have used the dataset to develop a quasi-3D model for the Greater Juha area, with associated cross-sections revealing that the exposed Cenozoic Darai Limestone is well-constrained with very low shortening of 12.6-21.4% yet structures are elevated up to 7 km above regional. We suggest the inversion of pre-existing rift architecture is the primary influence on the evolution of the area and that structures link to the surface via triangle zones and detachment faults within the incompetent Mesozoic passive-margin sedimentary sequence underlying competent Darai Limestone. Arc-normal oriented structures, dominantly oblique dextral, up-to-the-southeast, are pervasive across a range of scales and are here interpreted to relate at depth to weakened pre-existing basement cross-structures. It is proposed that Palaeozoic basement fabric controlled the structural framework of the basin during Early Mesozoic rifting forming regional-scale accommodation zones and related local-scale transfer structures that are now expressed as regional-scale arc-normal lineaments and local-scale arc-normal structures, respectively. Transfer structures, including complexly breached relay ramps, utilise northeast-southwest striking weaknesses associated with the basement fabric, as a mechanism for accommodating displacement along major northwest-southeast striking normal faults. These structures have subsequently been inverted to form arc-normal oriented zones of tear faulting that accommodate laterally variable

Drive alive: teen seat belt survey program.

Science.gov (United States)

Burkett, Katie M; Davidson, Steve; Cotton, Carol; Barlament, James; Loftin, Laurel; Stephens, James; Dunbar, Martin; Butterfield, Ryan

2010-08-01

To increase teen seat belt use among drivers at a rural high school by implementing the Drive Alive Pilot Program (DAPP), a theory-driven intervention built on highway safety best practices. The first component of the program was 20 observational teen seat belt surveys conducted by volunteer students in a high school parking lot over a 38-month period before and after the month-long intervention. The survey results were published in the newspaper. The second component was the use of incentives, such as gift cards, to promote teen seat belt use. The third component involved disincentives, such as increased police patrol and school policies. The fourth component was a programmatic intervention that focused on education and media coverage of the DAPP program. Eleven pre-intervention surveys and nine post-intervention surveys were conducted before and after the intervention. The pre- and post-intervention seat belt usage showed significant differences (p<0.0001). The average pre-intervention seat belt usage rate was 51.2%, while the average post-intervention rate was 74.5%. This represents a percentage point increase of 23.3 in seat belt use after the DAPP intervention. Based on seat belt observational surveys, the DAPP was effective in increasing seat belt use among rural high school teenagers. Utilizing a theory-based program that builds on existing best practices can increase the observed seat belt usage among rural high school students.

Chaos on the conveyor belt.

Science.gov (United States)

Sándor, Bulcsú; Járai-Szabó, Ferenc; Tél, Tamás; Néda, Zoltán

2013-04-01

The dynamics of a spring-block train placed on a moving conveyor belt is investigated both by simple experiments and computer simulations. The first block is connected by a spring to an external static point and, due to the dragging effect of the belt, the blocks undergo complex stick-slip dynamics. A qualitative agreement with the experimental results can be achieved only by taking into account the spatial inhomogeneity of the friction force on the belt's surface, modeled as noise. As a function of the velocity of the conveyor belt and the noise strength, the system exhibits complex, self-organized critical, sometimes chaotic, dynamics and phase transition-like behavior. Noise-induced chaos and intermittency is also observed. Simulations suggest that the maximum complexity of the dynamical states is achieved for a relatively small number of blocks (around five).

Tomography of the Chukou Fault Zone, Southwest Taiwan: Insights from Microearthquake Data

Directory of Open Access Journals (Sweden)

Yu-Lien Yeh

2016-06-01

Full Text Available The vigorous collision between the Eurasian plate and Philippine Sea plate in Taiwan causes a series of imbricate fold and thrust belts to develop at the deformation front. The Chukou Fault (CKF, characterized by a thrust type fault, located in Chiayi County, southwest (SW Taiwan, is a prominent boundary between the fold-thrust belts and the Western Coastal Plain. Most of the seismicity in SW Taiwan is associated with this fault and its neighboring fault systems. The seismotectonic structures in the CKF zone, especially in the east, are complex due to the interactions among fault systems with distinct slip motions. To gain better insights into the seismogenic characteristics in the CKF zone, we used 1661 microearthquakes recorded by a temporary dense broadband seismic network and the Central Weather Bureau Seismic Network (CWBSN between 2003 and 2004 to investigate the physical properties of the crust in the CKF zone. A waveform cross-correlation technique was applied to 143086 pairs of waveform data to determine the relative differential travel time between the P- and S-waves. By combining both the absolute and relative differential travel time data, we were able to obtain a new 3-D crustal P-wave velocity structure and Vp/Vs ratios. This study suggests that by using both absolute and relative differential travel time data in tomographic inversion can obtain precise 3-D velocity images and also gain better correlation between seismic events and fault structures, which is crucial for understanding the seismogenic process in our study area.

Early mantle dynamics inferred from 142Nd variations in Archean rocks from southwest Greenland

DEFF Research Database (Denmark)

Rizo, Hanika; Boyet, Maud; Blichert-Toft, Janne

2013-01-01

of the Greenland samples from a source formed in the Hadean. This mantle source is the oldest yet identified on Earth and therefore provides key information about the nature and evolution of early-differentiated reservoirs. In contrast, modern mantle-derived rocks from around the world do not have Nd-142 anomalies......The composition and evolution of the silicate Earth during Hadean/Eoarchean times are widely debated and largely unknown due to the sparse geological record preserved from Earth's infancy. The short-lived Sm-146-Nd-142 chronometer applied to 3.8-3.7 Ga old mantle-derived amphibolites from the Isua...... Supracrustal Belt (ISB) in southwest Greenland has revealed ubiquitous Nd-142 excesses in these rocks compared to modern samples and terrestrial Nd standards. Because the parent isotope, Sm-146, was extant only during the first few hundred million years of Solar System history, this implies derivation...

30 CFR 75.1403-5 - Criteria-Belt conveyors.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Criteria-Belt conveyors. 75.1403-5 Section 75... Criteria—Belt conveyors. (a) Positive-acting stop controls should be installed along all belt conveyors... can be stopped or started at any location. (b) Belt conveyors used for regularly scheduled mantrips...

Drive Alive: Teen Seat Belt Survey Program

Directory of Open Access Journals (Sweden)

Loftin, Laurel

2010-08-01

Full Text Available Objective: To increase teen seat belt use among drivers at a rural high school by implementing the Drive Alive Pilot Program (DAPP, a theory-driven intervention built on highway safety best practices.Methods: The first component of the program was 20 observational teen seat belt surveys conducted by volunteer students in a high school parking lot over a 38-month period before and after the month-long intervention. The survey results were published in the newspaper. The second component was the use of incentives, such as gift cards, to promote teen seat belt use. The third component involved disincentives, such as increased police patrol and school policies. The fourth component was a programmatic intervention that focused on education and media coverage of the DAPP program.Results: Eleven pre-intervention surveys and nine post-intervention surveys were conducted before and after the intervention. The pre- and post-intervention seat belt usage showed significant differences (p<0.0001. The average pre-intervention seat belt usage rate was 51.2%, while the average post-intervention rate was 74.5%. This represents a percentage point increase of 23.3 in seat belt use after the DAPP intervention.Conclusion: Based on seat belt observational surveys, the DAPP was effective in increasing seat belt use among rural high school teenagers. Utilizing a theory-based program that builds on existing best practices can increase the observed seat belt usage among rural high school students. [West J Emerg Med. 2010; 11(3: 280-283.

Synchronous and Cogged Fan Belt Performance Assessment

Energy Technology Data Exchange (ETDEWEB)

Cutler, Dylan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Dean, Jesse [National Renewable Energy Lab. (NREL), Golden, CO (United States); Acosta, Jason [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-02-01

The GSA Regional GPG Team commissioned the National Renewable Energy Laboratory (NREL) to perform monitoring of cogged V-belts and synchronous belts on both a constant volume and a variable air volume fan at the Byron G. Rodgers Federal Building and U.S. Courthouse in Denver, Colorado. These motor/fan combinations were tested with their original, standard V-belts (appropriately tensioned by an operation and maintenance professional) to obtain a baseline for standard operation. They were then switched to the cogged V-belts, and finally to synchronous belts. The power consumption by the motor was normalized for both fan speed and air density changes. This was necessary to ensure that the power readings were not influenced by a change in rotational fan speed or by the power required to push denser air. Finally, energy savings and operation and maintenance savings were compiled into an economic life-cycle cost analysis of the different belt options.

AUTOMATION OF CONVEYOR BELT TRANSPORT

Directory of Open Access Journals (Sweden)

Nenad Marinović

1990-12-01

Full Text Available Belt conveyor transport, although one of the most economical mining transport system, introduce many problems to mantain the continuity of the operation. Every stop causes economical loses. Optimal operation require correct tension of the belt, correct belt position and velocity and faultless rolls, which are together input conditions for automation. Detection and position selection of the faults are essential for safety to eliminate fire hazard and for efficient maintenance. Detection and location of idler roll faults are still open problem and up to now not solved successfully (the paper is published in Croatian.

Feed chute geometry for minimum belt wear

Energy Technology Data Exchange (ETDEWEB)

Roberts, A W; Wiche, S J [University of Newcastle, Newcastle, NSW (Australia). Centre for Bulk Solids and Particulate Technologies

1998-09-01

The paper is concerned with the feeding and transfer of bulk solids in conveyor belt operation. The paper focuses on chute design where the objective is to prevent spillage and minimise both chute and belt wear. It is shown that these objectives may be met through correct dynamic design of the chute and by directing the flow of bulk solids onto the belt at an acceptable incidence angle. The aim is to match the tangential velocity component of the feed velocity as close as possible to the belt velocity. At the same time, it is necessary to limit the impact pressure due to the change in momentum of the bulk solid as it feeds onto the belt. 2 refs., 8 figs.

Determination of relative immobile and sliding areas between carrying and tractive belts in using of belt conveyor intermediate drives

OpenAIRE

Goncharov K.A.

2015-01-01

Method of determination of relative immobile and sliding areas between carrying and tractive belts in places of mount-ing of belt conveyor intermediate drives made in the form of tractive contours is proposed. The example shows potential of this method in multidrive belt conveyor design process.

30 CFR 75.1108 - Approved conveyor belts.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Approved conveyor belts. 75.1108 Section 75... Fire-Resistant Hydraulic Fluids on Underground Equipment § 75.1108 Approved conveyor belts. (a) Until December 31, 2009 conveyor belts placed in service in underground coal mines shall be: (1) Approved under...

Effectiveness of media and enforcement campaigns in increasing seat belt usage rates in a state with a secondary seat belt law.

Science.gov (United States)

Vasudevan, Vinod; Nambisan, Shashi S; Singh, Ashok K; Pearl, Traci

2009-08-01

In 2005, in terms of seat belt usage rates, Nevada ranked third nationally and first among states with secondary seat belt use enforcement laws in the United States. An effective combination of a media-based education and enforcement campaign helped in this regard. The objective of this article is to document the effectiveness of enforcement and media-based education and outreach campaigns on the seat belt usage rates in Nevada, a state with a secondary seat belt usage law. Observational data on seat belt usage and passenger fatality data are used to evaluate the effectiveness of enforcement campaigns and media-based education and outreach campaigns. Data based on observations of about 40,000 vehicles in each of the years 2003 to 2005 were analyzed. Statistical analyses show that a significant increase in seat belt usage rates among both drivers and passengers for both genders resulted from the accompanying the media and enforcement campaigns. The results from this study indicate that effective and well-planned media/enforcement campaigns can have a significant impact on seat belt usage rates even in a state where the enforcement of seat belt laws can only be as a secondary violation. They validate and expand on findings from other efforts documented in the literature. These results demonstrate that, if coordinated properly, media and enforcement campaigns work very effectively in increasing seat belt usage rates even in states with secondary seat belt laws.

Determination of relative immobile and sliding areas between carrying and tractive belts in using of belt conveyor intermediate drives

Directory of Open Access Journals (Sweden)

Goncharov K.A.

2015-12-01

Full Text Available Method of determination of relative immobile and sliding areas between carrying and tractive belts in places of mount-ing of belt conveyor intermediate drives made in the form of tractive contours is proposed. The example shows potential of this method in multidrive belt conveyor design process.

Crustal Deformation around Zhangjiakou-Bohai Seismically Active Belt

Science.gov (United States)

Jin, H.; Fu, G.; Kato, T.

2011-12-01

Zhangjiakou-Bohai belt is a seismically active belt located in Northern China around Beijing, the capital of China. Near such a belt many great earthquakes occurred in the past centuries (e.g. the 1976 Tanshan Ms7.8 earthquake, the 1998 Zhangbei Ms6.2 earthquake, etc). Chinese Government established dense permanent and regional Global Positioning System (GPS) stations in and near the area. We collected and analyzed all the GPS observation data between 1999 and 2009 around Zhangjiakou-Bohai seismic belt, and obtained velocities at 143 stations. At the same time we investigated Zhangjiakou-Bohai belt slip rate for three profiles from northwest to southeast, and constructed a regional strain field on the Zhangjiakou-Bohai seismic belt region by least-square collocation. Based on the study we found that: 1) Nowadays the Zhangjiakou-Bohai seismic belt is creeping with left-lateral slip rate of 2.0mm~2.4mm/a, with coupling depth of 35~50km; 2) In total, the slip and coupling depth of the northwestern seismic belt is less than the one of southeast side; 3) The maximum shear strain is about 3×10-8 at Beijing-Tianjin-Tangshan area.

Method of monitoring, inspecting or testing conveyor belts

International Nuclear Information System (INIS)

Van der Walt, A.J.

1985-01-01

An invention is discussed which provides a method, installation and kit for monitoring, inspecting or testing a conveyor belt. Provision is made to transmit penetrating rays such as X-rays through a moving conveyor belt, forming a visible moving image from rays transmitted through the belt, and visually inspecting such moving image, after recording it if desired, to ascertain the condition of the interior of the belt. Typically an X-ray tube head is used to transmit the rays through the belt to a fluorescent screen which forms the image. The moving image can be recorded by means of a video camera

The development of an electronic system to continually monitor, indicate and control, 'belt slippage' in industrial friction 'V' belt drive transmission systems

International Nuclear Information System (INIS)

Brown, R E

2012-01-01

Belts have been used for centuries as a mechanism to transfer power from some form of drive system to a variety of load systems. Within industry today, many designs of belts but particularly friction, trapezoidal shaped 'V' belts are used and generally transfer power generated by electrical motors to numerous forms of driven load systems. It is suggested that belt systems, through their simplicity are sadly neglected by maintenance functions and generally are left unattended until high degrees of 'belt slippage' through loss of friction or 'belt breakage' provokes maintenance attention. These circumstances are most often identified through the reduced or loss of manufacturing production or the occurrence of catastrophic circumstances such as fire caused through excessive friction/ high belt slippage conditions. Obviously, these situations incur financial losses to companies and in some cases the near loss of the company's main manufacturing plant. Consequently, a satisfactory, viable solution is currently sought by industry to improve on current labour intensive maintenance practices. This paper will present an account of the development of an industrially robust, accurate and repeatable electronic system which continually monitors and indicates the degree of 'slippage' in a 'V' belt drive transmission system and in the circumstance of belt breakage or high belt slippage will enable and control the switching off the drive motor.

Grinding Glass Disks On A Belt Sander

Science.gov (United States)

Lyons, James J., III

1995-01-01

Small machine attached to table-top belt sander makes possible to use belt sander to grind glass disk quickly to specified diameter within tolerance of about plus or minus 0.002 in. Intended to be used in place of production-shop glass grinder. Held on driveshaft by vacuum, glass disk rotated while periphery ground by continuous sanding belt.

Colors of Inner Disk Classical Kuiper Belt Objects

Science.gov (United States)

Romanishin, W.; Tegler, S. C.; Consolmagno, G. J.

2010-07-01

We present new optical broadband colors, obtained with the Keck 1 and Vatican Advanced Technology telescopes, for six objects in the inner classical Kuiper Belt. Objects in the inner classical Kuiper Belt are of interest as they may represent the surviving members of the primordial Kuiper Belt that formed interior to the current position of the 3:2 resonance with Neptune, the current position of the plutinos, or, alternatively, they may be objects formed at a different heliocentric distance that were then moved to their present locations. The six new colors, combined with four previously published, show that the ten inner belt objects with known colors form a neutral clump and a reddish clump in B-R color. Nonparametric statistical tests show no significant difference between the B-R color distribution of the inner disk objects compared to the color distributions of Centaurs, plutinos, or scattered disk objects. However, the B-R color distribution of the inner classical Kuiper Belt Objects does differ significantly from the distribution of colors in the cold (low inclination) main classical Kuiper Belt. The cold main classical objects are predominately red, while the inner classical belt objects are a mixture of neutral and red. The color difference may reveal the existence of a gradient in the composition and/or surface processing history in the primordial Kuiper Belt, or indicate that the inner disk objects are not dynamically analogous to the cold main classical belt objects.

COLORS OF INNER DISK CLASSICAL KUIPER BELT OBJECTS

International Nuclear Information System (INIS)

Romanishin, W.; Tegler, S. C.; Consolmagno, G. J.

2010-01-01

We present new optical broadband colors, obtained with the Keck 1 and Vatican Advanced Technology telescopes, for six objects in the inner classical Kuiper Belt. Objects in the inner classical Kuiper Belt are of interest as they may represent the surviving members of the primordial Kuiper Belt that formed interior to the current position of the 3:2 resonance with Neptune, the current position of the plutinos, or, alternatively, they may be objects formed at a different heliocentric distance that were then moved to their present locations. The six new colors, combined with four previously published, show that the ten inner belt objects with known colors form a neutral clump and a reddish clump in B-R color. Nonparametric statistical tests show no significant difference between the B-R color distribution of the inner disk objects compared to the color distributions of Centaurs, plutinos, or scattered disk objects. However, the B-R color distribution of the inner classical Kuiper Belt Objects does differ significantly from the distribution of colors in the cold (low inclination) main classical Kuiper Belt. The cold main classical objects are predominately red, while the inner classical belt objects are a mixture of neutral and red. The color difference may reveal the existence of a gradient in the composition and/or surface processing history in the primordial Kuiper Belt, or indicate that the inner disk objects are not dynamically analogous to the cold main classical belt objects.

Speed Controlled Belt Conveyors: Drives and Mechanical Considerations

Directory of Open Access Journals (Sweden)

BEBIC, M. Z.

2018-02-01

Full Text Available The paper presents variable speed belt conveyor system where the reference speed is changed in order to achieve improved energy efficiency of operation. The recorded measurements show that belt tension varies within the same limits as under constant speed operation. These results introduce a new insight of the present state of the art in variable speed belt conveyor drives. The system is realized with remote control from the control center on an open pit mine. The structure of the multi-motor drive system of a single conveyor, as well as of the network-based control system distributed among belt conveyor stations and the control center are shown. Speed control of a belt conveyor system is organized to provide better utilization of the available material cross section on the belt and reduced electrical energy consumption of the drive. The experimental results obtained on the system prove that, under existing constraints, the applied algorithm has not introduced additional stress to the belt or mechanical assemblies during acceleration and deceleration processes, while providing higher energy efficiency of operation.

Timing belt in power transmission and conveying system

Directory of Open Access Journals (Sweden)

Domek Grzegorz

2018-01-01

Full Text Available This paper presents the problem of phenomena occurring at the contact of a timing belt and a pulley. Depending on a belt size range these phenomena differ significantly. There is no indication as to what solutions are optimal for drive belts. The analysis of the coupling process and performance tests have shown that the drive belt should have a cord of very good mechanical properties and its raceway side should be made from the material of a low friction coefficient against the pulley material. A flat belt in power transmission and conveying systems cooperates with several elements consisting of timing pulleys, tensioners or guiding rails. In gear with timing belts they depend strongly on characteristics of the process as well as the type of friction. In recent constructions, producers of timing belts are very much concerned about achieving as much slippery surface as possible. The work describes the problem of friction on different surfaces as well as its influence on gear lifetime. Research results confirm that on many surfaces bigger coefficient of friction is expected.

Conveyor belt weigher using a nuclear technique

International Nuclear Information System (INIS)

Magal, B.S.

1976-01-01

Principles of operation of different types of continuous conveyor belt weighing machines developed for use in factories for bulk weighing of material on conveyor belts without interupting the material flow, are briefly mentioned. The design of nuclear weighing scale making use of the radiation absorption property of the material used is described in detail. The radiation source, choice of the source, detector and geometry of such a weighing scale are discussed. The nucleonic belt weigher is compared with the gravimetric belt weigher system. The advantages of the nuclear system are pointed out. The assembly drawing of the electronics, calibration procedure and performance evaluation are given. (A.K.)

HERSCHEL -RESOLVED OUTER BELTS OF TWO-BELT DEBRIS DISKS—EVIDENCE OF ICY GRAINS

Energy Technology Data Exchange (ETDEWEB)

Morales, F. Y.; Bryden, G.; Werner, M. W.; Stapelfeldt, K. R., E-mail: Farisa@jpl.nasa.gov [Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Drive, Pasadena, CA 91109 (United States)

2016-11-01

We present dual-band Herschel /PACS imaging for 59 main-sequence stars with known warm dust ( T {sub warm} ∼ 200 K), characterized by Spitzer . Of 57 debris disks detected at Herschel wavelengths (70 and/or 100 and 160 μ m), about half have spectral energy distributions (SEDs) that suggest two-ring disk architectures mirroring that of the asteroid–Kuiper Belt geometry; the rest are consistent with single belts of warm, asteroidal material. Herschel observations spatially resolve the outer/cold dust component around 14 A-type and 4 solar-type stars with two-belt systems, 15 of which for the first time. Resolved disks are typically observed with radii >100 AU, larger than expected from a simple blackbody fit. Despite the absence of narrow spectral features for ice, we find that the shape of the continuum, combined with resolved outer/cold dust locations, can help constrain the grain size distribution and hint at the dust’s composition for each resolved system. Based on the combined Spitzer /IRS+Multiband Imaging Photometer (5-to-70 μ m) and Herschel /PACS (70-to-160 μ m) data set, and under the assumption of idealized spherical grains, we find that over half of resolved outer/cold belts are best fit with a mixed ice/rock composition. Minimum grain sizes are most often equal to the expected radiative blowout limit, regardless of composition. Three of four resolved systems around the solar-type stars, however, tend to have larger minimum grains compared to expectation from blowout ( f {sub MB} = a {sub min}/ a {sub BOS} ∼ 5). We also probe the disk architecture of 39 Herschel -unresolved systems by modeling their SEDs uniformly, and find them to be consistent with 31 single- and 8 two-belt debris systems.

Compliance with Seat Belt Use in Makurdi, Nigeria: An ...

African Journals Online (AJOL)

Background: Seat belts are designed to reduce injuries due to road crash among vehicle occupants. Aims: This study aims to determine the availability of seat belt in vehicles and compliance with seat belt use among vehicle occupants. Materials and methods: This was a 24‑h direct observational study of seat belt usage ...

Enclosed belts in the ascendancy

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-03-15

Although there will always be a place for traditional overland belt conveyors, enclosed belt systems are increasingly being specified where environmental protection assumes high priority or where there is a need to protect material from the weather. The article reports on recent conveyor projects such as: an MRC cable Belt in a 6.4 km system to carry coal in the Appalachian Mountains; a $40 m contract awarded to FL Smidth to supply an integrated coal handling system to LILIAMA in Vietnam and other contracts to handle coal for India's Coastal Gujarat Power; and a contract awarded to Bateman Engineered Technologies to supply a 7 km Japan Pipe Conveyor for a coal power station in Brazil. 3 photos.

Intelligent Belt Conveyor Monitoring and Control

NARCIS (Netherlands)

Pang, Y.

2010-01-01

Belt conveyors have been used worldwide in continuous material transport for about 250 years. Traditional inspection and monitoring of large-scale belt conveyors focus on individual critical components and response to catastrophic system failures. To prevent operational problems caused by the lack

Handbook Timing Belts Principles, Calculations, Applications

CERN Document Server

Perneder, Raimund

2012-01-01

Timing belts offer a broad range of innovative drivetrain solutions; they allow low-backlash operation in robot systems, they are widely used in automated processes and industrial handling involving highly dynamic start-up loads, they are low-maintenance solutions for continuous operation applications, and they can guarantee exact positioning at high operating speeds. Based on his years of professional experience, the author has developed concise guidelines for the dimensioning of timing belt drives and presents proven examples from the fields of power transmission, transport and linear transfer technology. He offers definitive support for dealing with and compensating for adverse operating conditions and belt damage, as well as advice on drive optimization and guidelines for the design of drivetrain details and supporting systems. All market-standard timing belts are listed as brand neutral. Readers will discover an extensive bibliography with information on the various manufacturers and their websites. This...

Energetic electrons in the inner belt in 1968

Energy Technology Data Exchange (ETDEWEB)

West, Jr, H I; Buck, R M [California Univ., Livermore (USA). Lawrence Livermore Lab.

1976-07-01

Pitch-angle data were obtained by the Lawrence Livermore Laboratory's scanning, magnetic electron spectrometer on OGO 5 during its traversals of the inner belt in 1968. Data from the five lowest-energy channels 79 to 822 keV, were analyzed. The inner-belt electron injection following two storm periods was observed; the first was the mild storm of 11 June and the second the more intense storms of 31 October and 1 November. Comparisons with other data indicate that only a small Starfish residual (at > 1 MeV) still remained in the heart of the inner belt; hence, the results are indicative of the normal inner belt. The data are discussed in terms of current ideas regarding the source and loss of particles in the inner belt.

SHRIMP U-Pb dating of detrital zircons in metamorphic rocks from northern Kyushu, western Japan

International Nuclear Information System (INIS)

Tsutsumi, Yukiyasu; Yokoyama, Kazumi; Terada, Kentaro; Sano, Yuji

2003-01-01

Radiometric ages of detrital zircons in psammitic schists from the Nagasaki, Kurume, Konoha and Kiyama areas, northern Kyushu, were obtained from 238 U/ 206 Pb ratio and isotopic compositions of Pb using a Sensitive High Resolution Ion Microprobe (SHRIMP II). Zircons from the Nagasaki, Kurume and Konoha areas show bimodal age distribution with peaks at ca. 1900 Ma and 250 Ma. It is suggested from this study that the older zircons were derived from Proterozoic landmass and the Korean Peninsula. Zircons from the Kiyama metamorphic rock show a different pattern with ages concentrated at 380-590 Ma. Such zircons are rare in rock samples from the Nagasaki, Kurume and Konoha areas, indicating that Kiyama rocks and a different origin than those from the other three areas. The youngest zircons from the Kiyama, Nagasaki, Kurume and Konoha areas show ages of 382±23 Ma, 238±13 Ma, 249±13 Ma, and 175±4 Ma, respectively, These data mark the upper age limit of their deposition. Since a continuous igneous activity occurred during the period from 300 to 170 Ma in Far East Asia, and the metamorphic age has been close to the zircon age of each area, these youngest ages for the Nagasaki, Kurume and Konoha areas are considered nearly contemporary to the depositional ages. An evaluation of the nature of metamorphism and available ages suggest the possibility that the Nagasaki metamorphic rocks as well as the schist from the Kurume area belong to the Suo zone of the Sangun belt, whereas the metamorphic rocks in the Konoha area may belong to the Ryoke belt or Suo zone of the Sangun belt. (author)

Belt design central to conveyor performance

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-15

While a conveyor system comprises a complex range of components, it is the belt design which ultimately dictates its core performance and reliability. The complexity of modern systems can be seen by the recent contract awarded to ThyssenKrupp Foerdertechnik (TKF) to supply systems for a new steel plant (including a coking plant and a power plant) to be built in Sepetiba Bay in Brazil. Phoenix has designed the Phoenotec system to protect steel cord conveyor belts. Fenner Dunlop has developed Fenaplast belting with nylon or polyester load-bearing warp and weft yarns for good impact resistance. 2 photos.

Geography of the asteroid belt

Science.gov (United States)

Zellner, B. H.

1978-01-01

The CSM classification serves as the starting point on the geography of the asteroid belt. Raw data on asteroid types are corrected for observational biases (against dark objects, for instance) to derive the distribution of types throughout the belt. Recent work on family members indicates that dynamical families have a true physical relationship, presumably indicating common origin in the breakup of a parent asteroid.

Klippen Belt, Flysch Belt and Inner Western Carpathian Paleogene Basin Relations in the Northern Slovakia by Magnetotelluric Imaging

Czech Academy of Sciences Publication Activity Database

Majcin, D.; Bezák, V.; Klanica, Radek; Vozár, J.; Pek, Josef; Bilčík, D.; Telecký, Josef

(2018) ISSN 0033-4553 Institutional support: RVO:67985530 Keywords : magnetotellurics * Western Carpathians * Klippen Belt * Flysch Belt * Inner Carpathian Paleogene Subject RIV: DE - Earth Magnetism, Geodesy, Geography OBOR OECD: Physical geography Impact factor: 1.591, year: 2016

7 CFR 1126.2 - Southwest marketing area.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Southwest marketing area. 1126.2 Section 1126.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE SOUTHWEST MARKETING AREA Order Regulating...

14 CFR 125.211 - Seat and safety belts.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Seat and safety belts. 125.211 Section 125... Requirements § 125.211 Seat and safety belts. (a) No person may operate an airplane unless there are available... the airplane who is at least 2 years old; and (2) An approved safety belt for separate use by each...

Belt Conveyor Dynamic Characteristics and Influential Factors

Directory of Open Access Journals (Sweden)

Junxia Li

2018-01-01

Full Text Available This paper uses the Kelvin-Voigt viscoelastic model to establish the continuous dynamic equations for tail hammer tension belt conveyors. The viscoelastic continuity equations are solved using the generalized coordinate method. We analyze various factors influencing longitudinal vibration of the belt conveyor by simulation and propose a control strategy to limit the vibration. The proposed approach and control strategy were verified by several experimental researches and cases. The proposed approach provides improved accuracy for dynamic design of belt conveyors.

Space Weather Effects in the Earth's Radiation Belts

Science.gov (United States)

Baker, D. N.; Erickson, P. J.; Fennell, J. F.; Foster, J. C.; Jaynes, A. N.; Verronen, P. T.

2018-02-01

The first major scientific discovery of the Space Age was that the Earth is enshrouded in toroids, or belts, of very high-energy magnetically trapped charged particles. Early observations of the radiation environment clearly indicated that the Van Allen belts could be delineated into an inner zone dominated by high-energy protons and an outer zone dominated by high-energy electrons. The energy distribution, spatial extent and particle species makeup of the Van Allen belts has been subsequently explored by several space missions. Recent observations by the NASA dual-spacecraft Van Allen Probes mission have revealed many novel properties of the radiation belts, especially for electrons at highly relativistic and ultra-relativistic kinetic energies. In this review we summarize the space weather impacts of the radiation belts. We demonstrate that many remarkable features of energetic particle changes are driven by strong solar and solar wind forcings. Recent comprehensive data show broadly and in many ways how high energy particles are accelerated, transported, and lost in the magnetosphere due to interplanetary shock wave interactions, coronal mass ejection impacts, and high-speed solar wind streams. We also discuss how radiation belt particles are intimately tied to other parts of the geospace system through atmosphere, ionosphere, and plasmasphere coupling. The new data have in many ways rewritten the textbooks about the radiation belts as a key space weather threat to human technological systems.

Southwest Regional Partnership on Carbon Sequestration

Energy Technology Data Exchange (ETDEWEB)

Brian McPherson

2006-03-31

The Southwest Partnership on Carbon Sequestration completed its Phase I program in December 2005. The main objective of the Southwest Partnership Phase I project was to evaluate and demonstrate the means for achieving an 18% reduction in carbon intensity by 2012. Many other goals were accomplished on the way to this objective, including (1) analysis of CO{sub 2} storage options in the region, including characterization of storage capacities and transportation options, (2) analysis and summary of CO{sub 2} sources, (3) analysis and summary of CO{sub 2} separation and capture technologies employed in the region, (4) evaluation and ranking of the most appropriate sequestration technologies for capture and storage of CO{sub 2} in the Southwest Region, (5) dissemination of existing regulatory/permitting requirements, and (6) assessing and initiating public knowledge and acceptance of possible sequestration approaches. Results of the Southwest Partnership's Phase I evaluation suggested that the most convenient and practical ''first opportunities'' for sequestration would lie along existing CO{sub 2} pipelines in the region. Action plans for six Phase II validation tests in the region were developed, with a portfolio that includes four geologic pilot tests distributed among Utah, New Mexico, and Texas. The Partnership will also conduct a regional terrestrial sequestration pilot program focusing on improved terrestrial MMV methods and reporting approaches specific for the Southwest region. The sixth and final validation test consists of a local-scale terrestrial pilot involving restoration of riparian lands for sequestration purposes. The validation test will use desalinated waters produced from one of the geologic pilot tests. The Southwest Regional Partnership comprises a large, diverse group of expert organizations and individuals specializing in carbon sequestration science and engineering, as well as public policy and outreach. These partners

Enhancing Eco-Efficiency of Agro-Products’ Closed-Loop Supply Chain under the Belt and Road Initiatives: A System Dynamics Approach

Directory of Open Access Journals (Sweden)

Rui Zhao

2018-03-01

Full Text Available This study redesigns the supply chain of agricultural products in southwest China under the Belt and Road Initiative to improve its eco-efficiency by considering the associated agro-wastes flowing into bioenergy enterprise for energy production. Two scenarios are created, in which the first assumes that all waste flows into the enterprise, whereas the second only considers the inflow of agro-waste produced by farmers and the wholesale market. A system dynamics simulation is conducted by using carbon emissions per product as an indicator to obtain the optimal scenario for managerial practice and design an incentivizing mechanism to drive supply chain operations. A case study is provided to demonstrate application of the system dynamics. Finally, the limitations of the study are discussed to lay the foundation for further improvement.

An Empirical Planetesimal Belt Radius–Stellar Luminosity Relation

Science.gov (United States)

Matrà, L.; Marino, S.; Kennedy, G. M.; Wyatt, M. C.; Öberg, K. I.; Wilner, D. J.

2018-05-01

Resolved observations of millimeter-sized dust, tracing larger planetesimals, have pinpointed the location of 26 Edgeworth–Kuiper Belt analogs. We report that a belt’s distance R to its host star correlates with the star’s luminosity L ⋆, following R\\propto {L}\\star 0.19 with a low intrinsic scatter of ∼17%. Remarkably, our Edgeworth–Kuiper Belt in the solar system and the two CO snow lines imaged in protoplanetary disks lie close to this R–L ⋆ relation, suggestive of an intrinsic relationship between protoplanetary disk structures and belt locations. To test the effect of bias on the relation, we use a Monte Carlo approach and simulate uncorrelated model populations of belts. We find that observational bias could produce the slope and intercept of the R–L ⋆ relation but is unable to reproduce its low scatter. We then repeat the simulation taking into account the collisional evolution of belts, following the steady-state model that fits the belt population as observed through infrared excesses. This significantly improves the fit by lowering the scatter of the simulated R–L ⋆ relation; however, this scatter remains only marginally consistent with the one observed. The inability of observational bias and collisional evolution alone to reproduce the tight relationship between belt radius and stellar luminosity could indicate that planetesimal belts form at preferential locations within protoplanetary disks. The similar trend for CO snow line locations would then indicate that the formation of planetesimals or planets in the outer regions of planetary systems is linked to the volatility of their building blocks, as postulated by planet formation models.

On-conveyor belt determination of ash in coal

International Nuclear Information System (INIS)

Sowerby, B.; Lim, C.S.; Abernethy, D.A.; Liu, Y.; Maguire, P.A.

1997-01-01

A laboratory feasibility study has been carried out on new and advanced neutron and gamma-ray analysis systems for the direct on-conveyor belt analysis of ash in coal without the need for sample by-lines. Such an analysis system could deliver the combined advantages of a direct on-conveyor configuration with new and accurate analysis techniques. An industry survey of 18 coal companies carried out in early 1996 indicated that accurate on-belt ash analysis is of the highest priority. Subsequent laboratory work has focussed on the investigation of methods with the potential for improving the accuracy of ash content measurement relative to existing on-belt ash analysers, the most widely-used of which are based on dual energy gamma-ray transmission (DUET), which is sensitive to variations in ash composition. The current work indicates that on-belt neutron/gamma-ray techniques combined with advanced spectral analysis techniques show promise for development into an on-belt ash analysis system which is significantly less sensitive to composition changes than DUET and which analyses a much larger proportion of coal on the belt, thus eliminating some key sources of analysis error

36 CFR 1004.15 - Safety belts.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Safety belts. 1004.15 Section 1004.15 Parks, Forests, and Public Property PRESIDIO TRUST VEHICLES AND TRAFFIC SAFETY § 1004.15 Safety... administered by the Presidio Trust will have the safety belt or child restraint system properly fastened at all...

Southwest Airlines: lessons in loyalty.

Science.gov (United States)

D'Aurizio, Patricia

2008-01-01

Southwest Airlines continues to garner accolades in the areas of customer service, workforce management, and profitability. Since both the health care and airlines industries deal with a service rather than a product, the customer experience depends on the people who deliver that experience. Employees' commitment or "loyalty" to their customers, their employer, and their work translates into millions of dollars of revenue. What employee wants to work for "the worst employer in town?" Nine loyalty lessons from Southwest can be carried over to the health care setting for the benefit of employees and patients.

Southwest University's No-Fee Teacher-Training Model

Science.gov (United States)

Chen, Shijian; Yang, Shuhan; Li, Linyuan

2013-01-01

The training model for Southwest University's no-fee teacher education program has taken shape over several years. Based on a review of the documentation and interviews with administrators and no-fee preservice students from different specialties, this article analyzes Southwest University's no-fee teacher-training model in terms of three main…

Estimates Of Radiation Belt Remediation Requirements

Science.gov (United States)

Tuszewski, M.; Hoyt, R. P.; Minor, B. M.

2004-12-01

A low-Earth orbit nuclear detonation could produce an intense artificial radiation belt of relativistic electrons. Many satellites would be destroyed within a few weeks. We present here simple estimates of radiation belt remediation by several different techniques, including electron absorption by gas release, pitch angle scattering by steady electric and magnetic fields from tether arrays, and pitch angle scattering by wave-particle interactions from in-situ transmitters. For each technique, the mass, size, and power requirements are estimated for a one-week remediation (e-folding) timescale, assuming that a 10 kTon blast trapped 1024 fission product electrons (1 to 8 MeV) at L = 1.5 in a dipolar belt of width dL = 0.1.

South and Southwest HSRC

Data.gov (United States)

Federal Laboratory Consortium — The Hazardous Substance Research Center/South and Southwest is a competitively awarded, peer-reviewed research consortium led by Louisiana State University with the...

Modeling of Jupiter's electron an ion radiation belts

International Nuclear Information System (INIS)

Sicard, Angelica

2004-01-01

In the Fifties, James Van Allen showed the existence of regions of the terrestrial magnetosphere consisted of energetic particles, trapped by the magnetic field: the radiation belts. The radiation belts of the Earth were the subject of many modeling works and are studied since several years at the Departement Environnement Spatial (DESP) of ONERA. In 1998, the DESP decided to adapt the radiation belts model of the Earth, Salammbo, to radiation environment of Jupiter. A first thesis was thus carried out on the subject and a first radiation belts model of electrons of Jupiter was developed [Santos-Costa, 2001]. The aim of this second thesis is to develop a radiation belts model for protons and heavy ions. In order to validate the developed model, the comparisons between Salammbo results and observations are essential. However, the validation is difficult in the case of protons and heavy ions because in-situ measurements of the probes are very few and most of the time contaminated by very energetic electrons. To solve this problem, a very good model of electrons radiation belts is essential to confirm or cancel the contamination of protons and heavy ions measurements. Thus, in parallel to the development of the protons and heavy ions radiation belts model, the electrons models, already existing, has been improved. Then Salammbo results have been compared to the different observations available (in-situ measurements, radio-astronomical observations). The different comparisons show a very good agreement between Salammbo results and observations. (author) [fr

Mesin Pemindah Bahan : Studi Prestasi Belt Conveyor Hubungannya Dengan Ukuran Butiran Dan Tingkat Kelembaban Bahan Curah ( Batubara ), Panjang Belt 7,6 Meter ; Lebar 32 Centimeter

OpenAIRE

Nugroho, Rio

2011-01-01

Banyak industri yang menggunakan belt conveyor sebagai alat transportasi material, sebab punya banyak keuntungan. Sehingga, untuk meningkatkan performansi belt conveyor tersebut perlu dilakukan pengidentifikasian prestasi belt conveyor. Identifikasi dilakukan dengan material transfer batubara. Yang akan diamati adalah pengaruh ukuran butiran material dan tingkat kelembaban terhadap kapasitas transfer belt conveyor. Dari pengujian didapatkan kapasitas transfer terbesar adalah material batubar...

Survey of current situation in radiation belt modeling

Science.gov (United States)

Fung, Shing F.

2004-01-01

The study of Earth's radiation belts is one of the oldest subjects in space physics. Despite the tremendous progress made in the last four decades, we still lack a complete understanding of the radiation belts in terms of their configurations, dynamics, and detailed physical accounts of their sources and sinks. The static nature of early empirical trapped radiation models, for examples, the NASA AP-8 and AE-8 models, renders those models inappropriate for predicting short-term radiation belt behaviors associated with geomagnetic storms and substorms. Due to incomplete data coverage, these models are also inaccurate at low altitudes (e.g., <1000 km) where many robotic and human space flights occur. The availability of radiation data from modern space missions and advancement in physical modeling and data management techniques have now allowed the development of new empirical and physical radiation belt models. In this paper, we will review the status of modern radiation belt modeling. Published by Elsevier Ltd on behalf of COSPAR.

Wearing an abdominal belt increases diastolic blood pressure.

Science.gov (United States)

Rafacz, W; McGill, S M

1996-09-01

The purpose of this study was to determine the effect of wearing an abdominal belt on blood pressure (systolic and diastolic) and heart rate during a variety of tasks. The belt was typical of the elastic type with suspenders and Velcro tabs for cinching the belt snug. The tasks performed included sitting at rest, sitting with the torso inclined forward at 45 degrees, standing with the torso inclined forward at 45 degrees (with and without holding an 11-kg weight), a trunk axial rotation task, and squat lifting. Blood pressure was monitored noninvasively with a FINAPRES blood pressure monitor. Twenty healthy men performed each task with and without the abdominal belt. Although no significant increases in mean systolic blood pressure or heart rate were found, there was a significant increase in diastolic blood pressure in all conditions. All people considering wearing an abdominal belt should also consider the risks and liability associated with the additional cardiovascular load, particularly heart attack and stroke.

Study on a metal pushing V-belt type CVT. Numerical analysis for belt tension distribution in brands of a ring at steady state; Kinzoku V belt wo mochiita CVT ni kansuru kenkyu. Sekiso belt (steel ring) no dendo kiko kaiseki

Energy Technology Data Exchange (ETDEWEB)

Fujii, T; Kuwabara, S [Doshisha University, Kyoto (Japan); Kanehara, S [Honda Motor Co. Ltd., Tokyo (Japan)

1997-10-01

The power transmitting mechanisms for laminated belts were studied to analyze belt tension in each band of the ring of metal V-belts. A numerical model consisting of linear springs and frictional elements was proposed. The present model was experimentally proved. It is revealed based on the numerical results that each band shares the ring tension equally when the coefficients of friction for bands and a pulley are the same while the first band must support more when the coefficients of friction between two bands are lower than that between a saddle surface of the block and the inner band. 4 refs., 9 figs.

An Effective Belt Conveyor for Underground Ore Transportation Systems

Science.gov (United States)

Krol, Robert; Kawalec, Witold; Gladysiewicz, Lech

2017-12-01

Raw material transportation generates a substantial share of costs in the mining industry. Mining companies are therefore determined to improve the effectiveness of their transportation system, focusing on solutions that increase both its energy efficiency and reliability while keeping maintenance costs low. In the underground copper ore operations in Poland’s KGHM mines vast and complex belt conveyor systems have been used for horizontal haulage of the run-of-mine ore from mining departments to shafts. Basing upon a long-time experience in the field of analysing, testing, designing and computing of belt conveyor equipment with regard to specific operational conditions, the improvements to the standard design of an underground belt conveyor for ore transportation have been proposed. As the key elements of a belt conveyor, the energy-efficient conveyor belt and optimised carrying idlers have been developed for the new generation of underground conveyors. The proposed solutions were tested individually on the specially constructed test stands in the laboratory and in the experimental belt conveyor that was built up with the use of prototype parts and commissioned for the regular ore haulage in a mining department in the KGHM underground mine “Lubin”. Its work was monitored and the recorded operational parameters (loadings, stresses and strains, energy dissipation, belt tracking) were compared with those previously collected on a reference (standard) conveyor. These in-situ measurements have proved that the proposed solutions will return with significant energy savings and lower maintenance costs. Calculations made on the basis of measurement results in the specialized belt conveyor designing software allow to estimate the possible savings if the modernized conveyors supersede the standard ones in a large belt conveying system.

Southwest Direct Express Bus Demonstration in Orlando, FL

Science.gov (United States)

1988-04-01

In August 1983, the Orange-Seminole-Osceola Transit Authority (OSOTA) initiated six express bus routes in the southwest corridor of Orlando (known collectively as the Southwest Direct) as an UMTA-funded demonstration project. While one objective of t...

The response of the southwest Western Australian wave climate to Indian Ocean climate variability

Science.gov (United States)

Wandres, Moritz; Pattiaratchi, Charitha; Hetzel, Yasha; Wijeratne, E. M. S.

2018-03-01

Knowledge of regional wave climates is critical for coastal planning, management, and protection. In order to develop a regional wave climate, it is important to understand the atmospheric systems responsible for wave generation. This study examines the variability of the southwest Western Australian (SWWA) shelf and nearshore wind wave climate and its relationship to southern hemisphere climate variability represented by various atmospheric indices: the southern oscillation index (SOI), the Southern Annular Mode (SAM), the Indian Ocean Dipole Mode Index (DMI), the Indian Ocean Subtropical Dipole (IOSD), the latitudinal position of the subtropical high-pressure ridge (STRP), and the corresponding intensity of the subtropical ridge (STRI). A 21-year wave hindcast (1994-2014) of the SWWA continental shelf was created using the third generation wave model Simulating WAves Nearshore (SWAN), to analyse the seasonal and inter-annual wave climate variability and its relationship to the atmospheric regime. Strong relationships between wave heights and the STRP and the STRI, a moderate correlation between the wave climate and the SAM, and no significant correlation between SOI, DMI, and IOSD and the wave climate were found. Strong spatial, seasonal, and inter-annual variability, as well as seasonal longer-term trends in the mean wave climate were studied and linked to the latitudinal changes in the subtropical high-pressure ridge and the Southern Ocean storm belt. As the Southern Ocean storm belt and the subtropical high-pressure ridge shifted southward (northward) wave heights on the SWWA shelf region decreased (increased). The wave height anomalies appear to be driven by the same atmospheric conditions that influence rainfall variability in SWWA.

Modeling and energy efficiency optimization of belt conveyors

International Nuclear Information System (INIS)

Zhang, Shirong; Xia, Xiaohua

2011-01-01

Highlights: → We take optimization approach to improve operation efficiency of belt conveyors. → An analytical energy model, originating from ISO 5048, is proposed. → Then an off-line and an on-line parameter estimation schemes are investigated. → In a case study, six optimization problems are formulated with solutions in simulation. - Abstract: The improvement of the energy efficiency of belt conveyor systems can be achieved at equipment and operation levels. Specifically, variable speed control, an equipment level intervention, is recommended to improve operation efficiency of belt conveyors. However, the current implementations mostly focus on lower level control loops without operational considerations at the system level. This paper intends to take a model based optimization approach to improve the efficiency of belt conveyors at the operational level. An analytical energy model, originating from ISO 5048, is firstly proposed, which lumps all the parameters into four coefficients. Subsequently, both an off-line and an on-line parameter estimation schemes are applied to identify the new energy model, respectively. Simulation results are presented for the estimates of the four coefficients. Finally, optimization is done to achieve the best operation efficiency of belt conveyors under various constraints. Six optimization problems of a typical belt conveyor system are formulated, respectively, with solutions in simulation for a case study.

"Abomination"--life as a Bible belt gay.

Science.gov (United States)

Barton, Bernadette

2010-01-01

Drawing on observation, autoethnography, and audio-taped interviews, this article explores the religious backgrounds and experiences of Bible Belt gays. In the Bible Belt, Christianity is not confined to Sunday worship. Christian crosses, messages, paraphernalia, music, news, and attitudes permeate everyday settings. Consequently, Christian fundamentalist dogma about homosexuality-that homosexuals are bad, diseased, perverse, sinful, other, and inferior-is cumulatively bolstered within a variety of other social institutions and environments in the Bible Belt. Of the 46 lesbians and gay men interviewed for this study (age 18-74 years), most describe living through spirit-crushing experiences of isolation, abuse, and self-loathing. This article argues that the geographic region of the Bible Belt intersects with religious-based homophobia. Informants explained that negative social attitudes about homosexuality caused a range of harmful consequences in their lives including the fear of going to hell, depression, low self-esteem, and feelings of worthlessness.

Gravity inferred subsurface structure of Gadwal Schist belt, Andhra

Indian Academy of Sciences (India)

Detailed gravity data collected across the Gadwal schist belt in the state of Andhra Pradesh show an 8.4 mgal residual gravity anomaly associated with meta-sediments/volcanics of the linear NNW-SSE trending schist belt that shows metamorphism from green schist to amphibolite facies. This schist belt is flanked on either ...

Using haptic feedback to increase seat belt use : traffic tech.

Science.gov (United States)

2011-07-01

The legacy of research on increasing seat belt use has : focused on enactment of seat belt legislation, public education, : high-visibility police enforcement, and seat belt : reminder systems. Several behavioral programs have : produced large, susta...

Seat belt injuries and sigmoid colon trauma.

OpenAIRE

Eltahir, E M; Hamilton, D

1997-01-01

Colonic seat belt injuries are rare but carry higher mortality rates than small bowel injuries. The case of a 44 year old man is described who had severe sigmoid colon compression injury from his seat belt a few days after a road traffic accident.

Radiometric measurement independent of profile. Belt weighers

International Nuclear Information System (INIS)

Otto, J.

1986-01-01

Radiometric measuring techniques allow contactless determination of the material carried by belt conveyors. Data defining the material is obtained via attenuation of gamma rays passing through the material on the belt. The method applies the absorption law according to Lambert-Beer, which has to be corrected by a build-up factor because of the stray radiation induced by the Compton effect. The profile-dependent error observed with conventional radiometric belt weighers is caused by the non-linearity of the absorption law in connection with the simultaneous summation of the various partial rays in a detector. The scanning method allows separate evaluation of the partial rays' attenuation and thus yields the correct data of the material carried, regardless of the profile. The scanning method is applied on a finite number of scanning sections, and a residual error has to be taken into account. The stochastics of quantum emission and absorption leads to an error whose expectation value is to be taken into account in the scanning algorithm. As the conveyor belt is in motion during the process of measurements, only part of the material conveyed is irradiated. The resulting assessment error is investigated as a function of the autocorrelation function of the material on the belt. (orig./HP) [de

A comparison of muscle activation between back squats and belt squats.

Science.gov (United States)

Evans, Thomas W; McLester, Cherilyn N; Howard, Jonathan H; McLester, John R; Calloway, Jimmy P

2017-06-08

A machine belt squat is a piece of equipment designed to allow the performance of squats while loading weight on the lifter's hips using a belt. The purpose of this investigation was to determine if belt squats differ from back squats in activation of the primary movers, and to determine the predictive capabilities of back squat load, training status, and anthropometric data on belt squat load. Thirty-one participants (16 males and 15 females) completed anthropometric measurements, a demographic questionnaire, a familiarization visit, and two testing visits, completing a 5 repetition maximum test for back squat and belt squat. Surface electromyography was used to measure muscle activation for the left and right vastus medialis (VMO), vastus lateralis (VLO), rectus femoris (RF), and gluteus maximus (GM). Comparison of muscle activation between the two exercises showed significant differences in the left GM (back squat: 0.84 ± 0.45, belt squat: 0.69 ± 0.22, p=0.015) and right GM (back squat: 0.86 ± 0.45, belt squat: 0.71 ± 0.29, p=0.004). Regression analysis computed significant prediction equations for belt squat load for general population, males, females, and advanced lifters. Overall, results indicate that belt squats may significantly differ in GM activation from back squats. Back squat load, as well as other variables, may be effective in accurately estimating appropriate belt squat load. These findings may help to more appropriately program for training with machine belt squats as a back squat alternative.

PRESENTDAY STRESS STATE OF THE SHANXI TECTONIC BELT

Directory of Open Access Journals (Sweden)

Wang Kaiying

2012-01-01

Full Text Available The Shanxi tectonic belt is a historically earthquakeabundant area. For the majority of strong earthquakes in this area, the distribution of earthquake foci was controlled by the N–S oriented local structures on the tectonic belt. Studies of the present stress state of the Shanxi tectonic belt can contribute to the understanding of the relationship between strong earthquakes’ occurrence and their structural distribution and also facilitate assessments of regional seismic danger and determination of the regions wherein strong earthquakes may occur in future. Using the Cataclastic Analysis Method (CAM, we performed stress inversion based on the focal mechanism data of earthquakes which took place in the Shanxi tectonic belt from 1967 to 2010. Our results show that orientations of the maximum principal compressive stress axis of the Shanxi tectonic belt might have been variable before and after the 2001 Kunlun MS=8.1 strong earthquake, with two different superior trends of the NW–SE and NE–SW orientation in different periods. When the maximum principal compressive stress axis is oriented in the NE–SW direction, the pattern of the space distribution of the seismic events in the Shanxi tectonic belt shows a trend of their concentration in the N–S oriented tectonic segments. At the same time, the stress state is registered as horizontal shearing and horizontal extension in the N–S and NE–SW oriented local segments in turn. When the maximum principal compressive stress axis is NW–SE oriented, the stress state of the N–S and NE–SW oriented tectonic segments is primarily registered as horizontal shearing. Estimations of plunges of stress axes show that seismicity in the Shanxi belt  corresponds primarily to the activity of lowangle faults, and highangle stress sites are located in the NE–SW oriented extensional tectonic segments of the Shanxi belt. This indicates that the stress change of the Shanxi belt is

The Dom Feliciano belt (Brazil-Uruguay)and its fore land (Rio de la Plata Craton): framework, tectonic evolution and correlations with similar terranes of southwestern Africa

International Nuclear Information System (INIS)

Basei, M.; Siga, O.; Masquelin, H.; Harara, O.; Reis Neto, J.; Preciozzi, F.

2000-01-01

The Dom Feliciano Belt (DFB) stretches for ca. 1,200 km along southeastern Brazil and eastern Uruguay, with an average width of 150 km. From its northern limit in Santa Catarina to its termination m Uruguay, DFB is internally organized according three crustal segments characterized, from southeast to northwest, by a Granitoid belt (calci-alkaline to alkaline granitoid rocks deformed to different degrees); a Schist belt (volcano-sedimentary rocks metamorphosed from green schist to amphibolite facies), and a Fore land belt (sedimentary and anchimetamorphic volcanic rocks), the latter situated between the Schist belt and the old western terranes. Despite discontinuously covered by younger sediments, the continuity of these three segments is suggested by the similar lithotypes and structural characteristics, as well as by the gravimetric geophysical signature.In this work, DBF is interpreted as the product of successive subduction s and collisions related to the agglutination of different terranes generated or intensely reworked from the Neoproterozoic to the Cambrian, during the Brasiliano and Rio Doce orogenesis, with maximum time starting at 900 Ma (opening of the Adamastor Ocean) and ending at 530 Ma (deformation of the fore land basins) related to the tecto no-magmatic events associated with the formation of the Western Gondwana.Besides the Neoproterozoic DFB and its fore land, the Rio de la Plata Craton and the Luis Alves Microplate, constituted by Paleoproterozoic gneissic-migmatitic rocks, two other tectonic units can be recognized in southeastern Brazil and eastern Uruguay: the Sao Gabriel Block (RS) where Neoproterozoic juvenile material can be characterized in regional scale (in great part associated with an island are), and the Punta del Este Terrane, which presents, in southern Uruguay, an ortho gneiss basement with ages around 1,000 Ma and a meta sedimentary cover (Rocha Group), which can correspond in the South-American portion, to the Namaqua and Gariep

Seat Belt Use Intention among Brazilian Undergraduate Students

OpenAIRE

TORQUATO, RENATA; FRANCO, CLÁUDIO M. A; BIANCHI, ALESSANDRA

2012-01-01

The objectives of this study were to explore self-reported seat belt use and group differences in different scenarios in a Brazilian sample and research the variables related to it. 120 college students answered a questionnaire with variables from the theory of planned behavior in order to evaluate the intention of seat belt use among car occupants. Results indicated that attitude and intention were the variables that most contributed to explaining seat belt use. Intention was highly correlat...

Asteroid Family Associations of Main-Belt Comets

Science.gov (United States)

Hsieh, Henry H.; Novakovic, Bojan; Kim, Yoonyoung; Brasser, Ramon

2016-10-01

We present a population-level analysis of the asteroid family associations of known main-belt comets or main-belt comet candidates (which, to date, have largely just been analyzed on individual bases as they have been discovered). In addition to family associations that have already been reported in the literature, we have identified dynamical relationships between 324P/La Sagra and the Alauda family, P/2015 X6 (PANSTARRS) and the Aeolia family, and P/2016 G1 (PANSTARRS) and the Adeona family. We will discuss the overall implications of these family associations, particularly as they pertain to the hypothesis that members of primitive asteroid family members may be more susceptible to producing observable sublimation-driven dust emission activity, and thus becoming main-belt comets. We will also discuss the significance of other dynamical and physical properties of a family or sub-family as they relate to the likelihood of that family containing one or more currently active main-belt comets.

Energy-saving belt conveyors installed in Polish collieries

Directory of Open Access Journals (Sweden)

Jerzy ANTONIAK

2010-01-01

Full Text Available An important problem of reducing energy consumption and dioxide emissions in the stage of construction and operation of mine belt conveyors is connected with their broad use in the industry. However, this notion is related to a reduction of electric energy consumption for conveyor drive and for production of conveyor components and assemblies (belts, rollers, load-bearing structure etc.. An essential role is played by an increased life of belt conveyors assemblies and components, principally belts. A reduced electric energy consumption results in a decreased CO2 emissions, e.g. hard coal – fired power station issues 0.28 kg CO2 per production of 1 kWh, in to answer production of 1 t steel accounts for 3.2 t CO2 emissions. The subject-matter presented in the paper concerning energy-saving in the horizontally and inclined mine belt conveyors installed in a Polish colliery – Anna, Jankowice and Marcel, has a big economic significance and it is important from the point of view of environmental protection.

Exploring the collisional evolution of the asteroid belt

Science.gov (United States)

Bottke, W.; Broz, M.; O'Brien, D.; Campo Bagatin, A.; Morbidelli, A.

2014-07-01

The asteroid belt is a remnant of planet-formation processes. By modeling its collisional and dynamical history, and linking the results to constraints, we can probe how the planets and small bodies formed and evolved. Some key model constraints are: (i) The wavy shape of the main-belt size distribution (SFD), with inflection points near 100-km, 10--20-km, 1 to a few km, and ˜0.1-km diameter; (ii) The number of asteroid families created by the catastrophic breakup of large asteroid bodies over the last ˜ 4 Gy, with the number of disrupted D > 100 km bodies as small as ˜20 or as large as 60; (iii) the flux of small asteroids derived from the main belt that have struck the Moon over the last 3.5 Ga --- crater SFDs on lunar terrains with known ages suggest the D 100 km bodies have been significantly battered, but only a fraction have been catastrophically disrupted. Conversely, most small asteroids today are byproducts of fragmentation events. These results are consistent with growing evidence that most of the prominent meteorite classes were produced by young asteroid families. The big question is how to use what we know to determine the main belt's original size and state. This work is ongoing, but dynamical models hint at many possibilities, including both the late arrival and late removal of material from the main belt. In addition, no model has yet properly accounted for the bombardment of the primordial main belt by leftover planetesimals in the terrestrial planet region. It is also possible to use additional constraints, such as the apparent paucity of Vesta-like or V-type objects in the outer main belt, to argue that the primordial main belt at best only 3--4 its current mass at its start. In our talk, we will review what is known, what has been predicted, and some intriguing directions for the future.

SMALL MAIN-BELT ASTEROID SPECTROSCOPIC SURVEY, PHASE II

Data.gov (United States)

National Aeronautics and Space Administration — This data set contains visible-wavelength (0.435-0.925 micron) spectra for 1341 main-belt asteroids observed during the second phase of the Small Main-belt Asteroid...

Continuing scearch for a new type charging belt

International Nuclear Information System (INIS)

Jones, N.L.

1995-01-01

The EN Tandem accelerator at Oak Ridge National Laboratory (ORNL) operates to support a varied program of atomic physics research. As such, the demands on the accelerator often require a range of operation from ∼0.38 to 7.0 MV on the terminal, with low ripple and long term steady state operation. The standard charging belts obtained from the manufacture have generally given acceptable performance, but it is reasonable that modem manufacturing techniques and materials could increase belt lifetimes and improve accelerator performance, particularly voltage ripple. A new belt of significantly different construction from that of the conventional belts was specified, purchased, and installed in 1993. After 2800 hours of use at voltages from 0.38 to 5.8 MV, it was removed from the accelerator in early August 1995

SOUTHWEST REGIONAL PARTNERSHIP ON CARBON SEQUESTRATION

Energy Technology Data Exchange (ETDEWEB)

Brian McPherson; Rick Allis; Barry Biediger; Joel Brown; Jim Cappa; George Guthrie; Richard Hughes; Eugene Kim; Robert Lee; Dennis Leppin; Charles Mankin; Orman Paananen; Rajesh Pawar; Tarla Peterson; Steve Rauzi; Jerry Stuth; Genevieve Young

2004-11-01

The Southwest Partnership Region includes six whole states, including Arizona, Colorado, Kansas, New Mexico, Oklahoma, and Utah, roughly one-third of Texas, and significant portions of adjacent states. The Partnership comprises a large, diverse group of expert organizations and individuals specializing in carbon sequestration science and engineering, as well as public policy and outreach. The main objective of the Southwest Partnership project is to achieve an 18% reduction in carbon intensity by 2012. The Partnership made great progress in this first year. Action plans for possible Phase II carbon sequestration pilot tests in the region are almost finished, including both technical and non-technical aspects necessary for developing and carrying out these pilot tests. All partners in the Partnership are taking an active role in evaluating and ranking optimum sites and technologies for capture and storage of CO{sub 2} in the Southwest Region. We are identifying potential gaps in all aspects of potential sequestration deployment issues.

Transfer points of belt conveyors operating with unfavorable bulk

Energy Technology Data Exchange (ETDEWEB)

Goehring, H [Technische Universitaet, Dresden (German Democratic Republic)

1989-06-01

Describes design of belt conveyor chutes that transfer bulk of surface mines from one conveyor to another. Conveyor belt velocity is a significant parameter. Unfavorable chute design may lead to bulk flow congestion, bulk velocity losses etc. The bulk flow process is analyzed, bulk flow velocities, belt inclinations and bulk feeding from 2 conveyors into one chute are taken into account. Conventional chutes have parabolic belt impact walls. An improved version with divided impact walls is proposed that maintains a relatively high bulk velocity, reduces friction at chute walls and decreases wear and dirt build-up. Design of the improved chute is explained. It is built to adapt to existing structures without major modifications. The angle between 2 belt conveyors can be up to 90 degrees, the best bulk transfer is noted at conveyor angles below 60 degrees. Various graphs and schemes are provided. 6 refs.

Non-linear belt transient analysis. A hybrid model for numerical belt conveyor simulation

Energy Technology Data Exchange (ETDEWEB)

Harrison, A. [Scientific Solutions, Inc., Aurora, CO (United States)

2008-07-01

Frictional and rolling losses along a running conveyor are discussed due to their important influence on wave propagation during starting and stopping. Hybrid friction models allow belt rubber losses and material flexing to be included in the initial tension calculations prior to any dynamic analysis. Once running tensions are defined, a numerical integration method using non-linear stiffness gradients is used to generate transient forces during starting and stopping. A modified Euler integration technique is used to simulate the entire starting and stopping cycle in less than 0.1 seconds. The procedure enables a faster scrutiny of unforeseen conveyor design issues such as low belt tension zones and high forces at drives. (orig.)

Selection of Belt Conveyors Drive Units Number by Technical –Economical Analysis

OpenAIRE

Despodov, Zoran; Mijalkovski, Stojance; Adjiski, Vancho; Panov, Zoran

2014-01-01

In this paper is presented a methodology for selection of belt conveyor drive units number by technical - economical analysis of their parameters. Belt Conveyors with follow drive arrangement will be considered: one, two, three and four drive units. In the technical - economical analysis are including: Tension forces, Power of belt conveyor, Costs for belt, Costs for power and reducers, Total cost for belt conveyor system.

Green operations of belt conveyors by means of speed control

NARCIS (Netherlands)

He, D.; Pang, Y.; Lodewijks, G.

2017-01-01

Belt conveyors can be partially loaded due to the variation of bulk material flow loaded onto the conveyor. Speed control attempts to reduce the belt conveyor energy consumption and to enable the green operations of belt conveyors. Current research of speed control rarely takes the conveyor dynamics

[The velocity of HCV subtype 6a transmission in southwest China].

Science.gov (United States)

Hong, Guo-hu; Tan, Zhao-xia; Guo, Yan; Mao, Qing

2011-07-01

To estimate the velocity of HCV subtype 6a transmission in Southwest China. The HCV CE1 region from 61 patients infected with HCV genotype 6 were amplificated by RT-PCR and sequenced. The subtypes were identified, and the period of HCV 6a strains originated in southwest china was estimated by using molecular clock phylogenetic analysis. The velocity of HCV subtype 6a transmission in southwest China was estimated by BEAST v1.6.1 and Tracer v1.5 software theoretically. Most of HCV 6a strains distributed in Southwest China origine around the year 1968 and at last 4 epidemic strains existed. The earlier origine strains could be isolated both in intravenous drug users (IDU) and non-IDU patients. After 1997, the HCV 6a strains transmission in southwest China accelerated and the trend intensified in 2007. HCV 6a strains spread fastly both in IDU and non-IDU patients, which might be the main HCV subtype distributed in Southwest China in the future.

Radiation belt seed population and its association with the relativistic electron dynamics: A statistical study: Radiation Belt Seed Population

International Nuclear Information System (INIS)

Tang, C. L.; Wang, Y. X.; Ni, B.; Zhang, J.-C.

2017-01-01

Using the Van Allen Probes data, we study the radiation belt seed population and it associated with the relativistic electron dynamics during 74 geomagnetic storm events. Based on the flux changes of 1 MeV electrons before and after the storm peak, these storm events are divided into two groups of “non-preconditioned” and “preconditioned”. The statistical study shows that the storm intensity is of significant importance for the distribution of the seed population (336 keV electrons) in the outer radiation belt. However, substorm intensity can also be important to the evolution of the seed population for some geomagnetic storm events. For non-preconditioned storm events, the correlation between the peak fluxes and their L-shell locations of the seed population and relativistic electrons (592 keV, 1.0 MeV, 1.8 MeV, and 2.1 MeV) is consistent with the energy-dependent dynamic processes in the outer radiation belt. For preconditioned storm events, the correlation between the features of the seed population and relativistic electrons is not fully consistent with the energy-dependent processes. It is suggested that the good correlation between the radiation belt seed population and ≤1.0 MeV electrons contributes to the prediction of the evolution of ≤1.0 MeV electrons in the Earth’s outer radiation belt during periods of geomagnetic storms.

MACRO MODEL OF SEAT BELT USE BY CAR DRIVERS AND PASSENGERS

Directory of Open Access Journals (Sweden)

Kazimierz JAMROZ

2013-12-01

Full Text Available The article presents some problems of seat belt use by car drivers and passengers. It looks in particular at seat belt use and effectiveness in selected countries. Next, factors of seat belt use are presented and methodology of model development. A macro model of seat belt use is presented based on data from around fifty countries from different continents.

High-energy outer radiation belt dynamic modeling

International Nuclear Information System (INIS)

Chiu, Y.T.; Nightingale, R.W.; Rinaldi, M.A.

1989-01-01

Specification of the average high-energy radiation belt environment in terms of phenomenological montages of satellite measurements has been available for some time. However, for many reasons both scientific and applicational (including concerns for a better understanding of the high-energy radiatino background in space), it is desirable to model the dynamic response of the high-energy radiation belts to sources, to losses, and to geomagnetic activity. Indeed, in the outer electron belt, this is the only mode of modeling that can handle the large intensity fluctuations. Anticipating the dynamic modeling objective of the upcoming Combined Release and Radiation Effects Satellite (CRRES) program, we have undertaken to initiate the study of the various essential elements in constructing a dynamic radiation belt model based on interpretation of satellite data according to simultaneous radial and pitch-angle diffusion theory. In order to prepare for the dynamic radiation belt modeling based on a large data set spanning a relatively large segment of L-values, such as required for CRRES, it is important to study a number of test cases with data of similar characteristics but more restricted in space-time coverage. In this way, models of increasing comprehensiveness can be built up from the experience of elucidating the dynamics of more restrictive data sets. The principal objectives of this paper are to discuss issues concerning dynamic modeling in general and to summarize in particular the good results of an initial attempt at constructing the dynamics of the outer electron radiation belt based on a moderately active data period from Lockheed's SC-3 instrument flown on board the SCATHA (P78-2) spacecraft. Further, we shall discuss the issues brought out and lessons learned in this test case

Bayesian inference of radiation belt loss timescales.

Science.gov (United States)

Camporeale, E.; Chandorkar, M.

2017-12-01

Electron fluxes in the Earth's radiation belts are routinely studied using the classical quasi-linear radial diffusion model. Although this simplified linear equation has proven to be an indispensable tool in understanding the dynamics of the radiation belt, it requires specification of quantities such as the diffusion coefficient and electron loss timescales that are never directly measured. Researchers have so far assumed a-priori parameterisations for radiation belt quantities and derived the best fit using satellite data. The state of the art in this domain lacks a coherent formulation of this problem in a probabilistic framework. We present some recent progress that we have made in performing Bayesian inference of radial diffusion parameters. We achieve this by making extensive use of the theory connecting Gaussian Processes and linear partial differential equations, and performing Markov Chain Monte Carlo sampling of radial diffusion parameters. These results are important for understanding the role and the propagation of uncertainties in radiation belt simulations and, eventually, for providing a probabilistic forecast of energetic electron fluxes in a Space Weather context.

Optimal control of operation efficiency of belt conveyor systems

International Nuclear Information System (INIS)

Zhang, Shirong; Xia, Xiaohua

2010-01-01

The improvement of the energy efficiency of belt conveyor systems can be achieved at equipment or operation levels. Switching control and variable speed control are proposed in literature to improve energy efficiency of belt conveyors. The current implementations mostly focus on lower level control loops or an individual belt conveyor without operational considerations at the system level. In this paper, an optimal switching control and a variable speed drive (VSD) based optimal control are proposed to improve the energy efficiency of belt conveyor systems at the operational level, where time-of-use (TOU) tariff, ramp rate of belt speed and other system constraints are considered. A coal conveying system in a coal-fired power plant is taken as a case study, where great saving of energy cost is achieved by the two optimal control strategies. Moreover, considerable energy saving resulting from VSD based optimal control is also proved by the case study.

Optimal control of operation efficiency of belt conveyor systems

Energy Technology Data Exchange (ETDEWEB)

Zhang, Shirong [Department of Automation, Wuhan University, Wuhan 430072 (China); Xia, Xiaohua [Department of Electrical, Electronic and Computer Engineering, University of Pretoria, Pretoria 0002 (South Africa)

2010-06-15

The improvement of the energy efficiency of belt conveyor systems can be achieved at equipment or operation levels. Switching control and variable speed control are proposed in literature to improve energy efficiency of belt conveyors. The current implementations mostly focus on lower level control loops or an individual belt conveyor without operational considerations at the system level. In this paper, an optimal switching control and a variable speed drive (VSD) based optimal control are proposed to improve the energy efficiency of belt conveyor systems at the operational level, where time-of-use (TOU) tariff, ramp rate of belt speed and other system constraints are considered. A coal conveying system in a coal-fired power plant is taken as a case study, where great saving of energy cost is achieved by the two optimal control strategies. Moreover, considerable energy saving resulting from VSD based optimal control is also proved by the case study. (author)

Belt conveyor dynamics in transient operation for speed control

OpenAIRE

He, D.; Pang, Y.; Lodewijks, G.

2016-01-01

Belt conveyors play an important role in continuous dry bulk material transport, especially at the mining industry. Speed control is expected to reduce the energy consumption of belt conveyors. Transient operation is the operation of increasing or decreasing conveyor speed for speed control. According to literature review, current research rarely takes the conveyor dynamics in transient operation into account. However, in belt conveyor speed control, the conveyor dynamic behaviors are signifi...

Deconstructing the conveyor belt.

Science.gov (United States)

Lozier, M Susan

2010-06-18

For the past several decades, oceanographers have embraced the dominant paradigm that the ocean's meridional overturning circulation operates like a conveyor belt, transporting cold waters equatorward at depth and warm waters poleward at the surface. Within this paradigm, the conveyor, driven by changes in deepwater production at high latitudes, moves deep waters and their attendant properties continuously along western boundary currents and returns surface waters unimpeded to deepwater formation sites. A number of studies conducted over the past few years have challenged this paradigm by revealing the vital role of the ocean's eddy and wind fields in establishing the structure and variability of the ocean's overturning. Here, we review those studies and discuss how they have collectively changed our view of the simple conveyor-belt model.

Petrology and geochemistry of the Grouse Canyon Member of the Belted Range Tuff, Rock-Mechanics Drift, U12g Tunnel, Nevada Test Site

International Nuclear Information System (INIS)

Connolly, J.R.; Mansker, W.L.; Hicks, R.; Allen, C.C.; Husler, J.; Keil, K.; Lappin, A.R.

1983-04-01

G-Tunnel at Nevada Test Site (NTS) is the site of thermal and thermomechanical experiments examining the feasibility of emplacing heat-producing nuclear wastes in silicic tuffs. This report describes the general stratigraphy, mineralogy, and bulk chemistry of welded portions of the Grouse Canyon Member of the Belted Range Tuff, the unit in which most of these experiments will be performed. The geologic characteristics of the Grouse Canyon Member are compared with those of the Topopah Spring Member of the Paintbrush Tuff, presently the preferred horizon for an actual waste repository at Yucca Mountain, near the southwest boundary of Nevada Test Site. This comparison suggests that test results obtained in welded tuff from G-Tunnel are applicable, with limitations, to evaluation of the Topopah Spring Member at Yucca Mountain

Design of belt conveyors in bulk terminal applications. Part II

Energy Technology Data Exchange (ETDEWEB)

Goodwin, P J; Ramos, C M

1986-04-01

The main design parameters used for belt conveyors in harbour applications are discussed. Conveyor belting including the carcass, belt cover, belt tension and speed, and safety factors, idlers, conveyor pulleys, motors, fluid couplings and drive arrangements are considered. Technical factors are briefly outlined for the designer to consider to achieve minimum acceptable component service life. A method is discussed to reduce coal degradation investigated using a test chute designed for the purpose of minimizing sized coal degradation at transfer points in the refurbishing of the Durban Coal Terminal. 24 references.

Health Monitoring for Coated Steel Belts in an Elevator System

Directory of Open Access Journals (Sweden)

Huaming Lei

2012-01-01

Full Text Available This paper presents a method of health monitoring for coated steel belts in an elevator system by measuring the electrical resistance of the ropes embedded in the belt. A model on resistance change caused by fretting wear and stress fatigue has been established. Temperature and reciprocating cycles are also taken into consideration when determining the potential strength degradation of the belts. It is proved by experiments that the method could effectively estimate the health degradation of the most dangerous section as well as other ones along the whole belts.

IDENTIFYING COLLISIONAL FAMILIES IN THE KUIPER BELT

International Nuclear Information System (INIS)

Marcus, Robert A.; Ragozzine, Darin; Murray-Clay, Ruth A.; Holman, Matthew J.

2011-01-01

The identification and characterization of numerous collisional families-clusters of bodies with a common collisional origin-in the asteroid belt has added greatly to the understanding of asteroid belt formation and evolution. More recent study has also led to an appreciation of physical processes that had previously been neglected (e.g., the Yarkovsky effect). Collisions have certainly played an important role in the evolution of the Kuiper Belt as well, though only one collisional family has been identified in that region to date, around the dwarf planet Haumea. In this paper, we combine insights into collisional families from numerical simulations with the current observational constraints on the dynamical structure of the Kuiper Belt to investigate the ideal sizes and locations for identifying collisional families. We find that larger progenitors (r ∼ 500 km) result in more easily identifiable families, given the difficulty in identifying fragments of smaller progenitors in magnitude-limited surveys, despite their larger spread and less frequent occurrence. However, even these families do not stand out well from the background. Identifying families as statistical overdensities is much easier than characterizing families by distinguishing individual members from interlopers. Such identification seems promising, provided the background population is well known. In either case, families will also be much easier to study where the background population is small, i.e., at high inclinations. Overall, our results indicate that entirely different techniques for identifying families will be needed for the Kuiper Belt, and we provide some suggestions.

Southwest Energy Efficiency Project (SWEEP) Final Report

Energy Technology Data Exchange (ETDEWEB)

Geller, Howard [Southwest Energy Efficiency Project (SWEEP), Boulder, CO (United States); Meyers, Jim [Southwest Energy Efficiency Project (SWEEP), Boulder, CO (United States)

2018-01-29

SWEEP worked with Energy Efficiency and Renewable Energy (EERE) programs to foster greater energy efficiency throughout the Southwest. SWEEP accomplished this through a combination of analysis and support; preparation and distribution of materials on best practice technologies, policies and programs; and technical assistance and information dissemination to states and municipalities in the southwest supporting BTO, AMO, OWIP for advancement of efficiency in products and practices. These efforts were accomplished during the period 2012 through 2017.

Coal belt options

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-03-15

Whether moving coal long distances overland or short distances in-plant, belt conveyors will always be in demand. The article reports on recent systems developments and applications by Beumer, Horizon Conveyor Equipment, Conveyor Dynamics, Doppelmayr Transport Technology, Enclosed Bulk Systems, ContiTech and Bateman Engineered Technologies. 2 photos.

A Parametric Energy Model for Energy Management of Long Belt Conveyors

Directory of Open Access Journals (Sweden)

Tebello Mathaba

2015-12-01

Full Text Available As electricity prices continue to rise, the increasing need for energy management requires better understanding of models for energy-consuming applications, such as conveyor belts. Conveyor belts are used in a wide range of industries, including power generation, mining and mineral processing. Conveyor technological advances are leading to increasingly long conveyor belts being commissioned. Thus, the energy consumption of each individual belt conveyor unit is becoming increasingly significant. This paper proposes a generic energy model for belt conveyors with long troughed belts. The model has a two-parameter power equation, and it uses a partial differential equation to capture the variable amount of material mass per unit length throughout the belt length. Verification results show that the power consumption calculations of the newly proposed simpler model are consistent with those of a known non-linear model with an error of less than 4%. The online parameter identification set-up of the model is proposed. Simulations indicate that the parameters can be identified successfully from data with up to 15% measurement noise. Results show that the proposed model gives better predictions of the power consumed and material delivered by a long conveyor belt than the steady-state models in the current literature.

RATIONALE FOR CENTERING CAPACITY OF REDISIGNED BELT CONVEYOR DRUMS

Directory of Open Access Journals (Sweden)

V. V. Suglobov

2016-02-01

Full Text Available Purpose. In the study is necessary: 1 to justify aligning drums of a new design of belt conveyors; 2 to develop a method for calculating and determining the rational design parameters of drums depending on the technical parameters of the conveyor belt (the length of the conveyor, belt width, the performance of the conveyor, the diameter of the drive and tension drums, etc.; 3 to carry out pilot studies of efficiency conveyor belt in a production environment in order to determine the magnitude of dynamic loads and a comparative evaluation of the effectiveness of the centering ability of conventional and new designs of drums. Methodology. To substantiate the effectiveness of the centering ability of the drums of a new design by the authors developed a mathematical model of interaction of the tape with the drum. Mathematical simulation of tape reels with new design comes to drawing up a differential equation of the belt based on the dynamic component and restoring force. This model allowed us to estimate the movement of the tape in the transverse direction based on the calculated additional dynamic loads and forces on the investigated centering a conveyor belt with given specifications. For the first time the technique of calculating and determining the rational parameters of the drums, which allows determining the design parameters of the centering portions, depending on the mechanical properties and geometric parameters of the tape. Findings. With the help of mathematical modeling the scientifically substantiated effect of centering the ability of the new design of the drum, which ensures stable tape running along the longitudinal axis of the conveyor. The authors made the following conclusions: 1 the mathematical model of interaction with the new belt design of the drum, which allowed to describe the belt in the transverse direction in view of additional dynamic loads and renewable power was developed; 2 the method of calculation and

Energy saving for belt conveyors by speed control

NARCIS (Netherlands)

He, D.

2017-01-01

Belt conveyors are widely used in bulk solids handling and conveying systems. Considering the extensive use of belt conveyors, their operations involve a large amount of energy. Taking the relevant economic and social challenges into account, there is a strong demand for lowering the energy

Angle stations in or for endless conveyor belts

Science.gov (United States)

Steel, Alan

1987-04-07

In an angle station for an endless conveyor belt, there are presented to each incoming run of the belt stationary curved guide members (18, 19) of the shape of a major segment of a right-circular cylinder and having in the part-cylindrical portion (16 or 17) thereof rectangular openings (15) arranged in parallel and helical paths and through which project small freely-rotatable rollers (14), the continuously-changing segments of the curved surfaces of which projecting through said openings (15) are in attitude to change the direction of travel of the belt (13) through 90.degree. during passage of the belt about the part-cylindrical portion (16 or 17) of the guide member (18 or 19). The rectangular openings (15) are arranged with their longer edges lengthwise of the diagonals representing the mean of the helix but with those of a plurality of the rows nearest to each end of the part-cylindrical portion (16 or 17) slightly out of axial symmetry with said diagonals, being slightly inclined in a direction about the intersections (40) of the diagonals of the main portion of the openings, to provide a "toe-in" attitude in relation to the line of run of the endless conveyor belt.

Seat-belt message and the law?

Science.gov (United States)

Sengupta, S K; Patil, N G; Law, G

1989-09-01

This paper attempts to draw together available information on the use of seat belts, one of the most important safety devices for a person in a car. Considering the high rate of mortality and morbidity due to road traffic accidents in Papua New Guinea the authors strongly feel that seat-belt usage should be made compulsory. When one looks at the history of the implementation of such a successful countermeasure in other countries it seems that legislation is the only answer.

Magnetic refrigeration apparatus with belt of ferro or paramagnetic material

Science.gov (United States)

Barclay, John A.; Stewart, Walter F.; Henke, Michael D.; Kalash, Kenneth E.

1987-01-01

A magnetic refrigerator operating in the 12 to 77K range utilizes a belt which carries ferromagnetic or paramagnetic material and which is disposed in a loop which passes through the center of a solenoidal magnet to achieve cooling. The magnetic material carried by the belt, which can be blocks in frames of a linked belt, can be a mixture of substances with different Curie temperatures arranged such that the Curie temperatures progressively increase from one edge of the belt to the other. This magnetic refrigerator can be used to cool and liquefy hydrogen or other fluids.

Southwest Center for Environmental Excellence and Opportunity Year End Report (Final Deliverable)

Energy Technology Data Exchange (ETDEWEB)

None

1998-11-09

The Southwest Center for Environmental Excellence and Opportunity (Southwest CEEO) has been in existence since October 1996 at Albuquerque Technical Vocational Institute's (TVI) South Valley Campus. The Special Project was comprised of three objectives: (1) Increasing the number of Hispanics in careers related to the environment by improving education and job training opportunities; (2) Strengthening the infrastructure of Hispanic businesses and building their capacity to participate in environmental clean-up activities and potential technology commercialization; and (3) Increasing the Hispanic community's understanding of and participation in environmental protection through improved access to information and outreach activities, paying attention to cultural and linguistic issues. The Southwest CEEO has been successful in each of the above objective areas and continues to provide valuable services to TVI and the community. The Southwest CEEO has developed a scholarship/mentorship program involving business and industry, community organizations, and TVI faculty that will be replicated by other student mentorship programs. The Southwest CEEO has awarded approximately $50,000 over the two-year program funded by the U.S. Department of Energy Oakland Operations Office. The Southwest CEEO has also developed a K-12 partnership with Albuquerque Public Schools (APS) to enhance environmental education for students and professional development for teachers. Incorporated into these student activities are experimental learning opportunities and curriculum development and/or enhancement. The Southwest CEEO has worked closely with the TVI Small Business Development Center (SBDC) to support Hispanic businesses in technology partnership activities. The Southwest CEEO in partnership the TVI SBDC has provided a large business forum and business workshops. In addition, the Southwest CEEO has developed a Technology Transfer Model that will be expanded in the future to a

Gan-Hang tectonic belt and its geologic significance

International Nuclear Information System (INIS)

Deng Jiarui; Zhang Zhiping.

1989-01-01

Gan-Hang tectonic belt is predominantly controlled by Gan-Hang fracture zone. It is mainly composed of Yongfeng-Zhuji downwarping zone, Gan-Hang volcanic activity structural belt and Gan-Hang red basin downfaulted zone. Gan-Hang fracture zone is derived from evolution and development of Shaoxing-Jiangshan deep fracture. It is mainly composed of three deep and large fracture and Fuzhou-Yongfeng large fracture. The fracture zone is a long active belt, but in each active period the geologic structural patterns intensity, depth and forming time were not same. Gan-Hang tectonic belt possesses obvious inheritance. It has always maintained the character of the relative depression or low land since the Caledonian movement. This specific structural environment is favourable for uranium mineralization. At any rate, the formation of this uranium minerogenetic zone has been experiencing a long and complicated processes which were closely associated with long activity of Gan-Hang fracture zone

Magmatic formations in the Okhotsk--Chukotka volcanogenic belt

Energy Technology Data Exchange (ETDEWEB)

Osipov, A.P.

1976-05-01

The relationship between the Okhotsk-Chukotka volcanogenic belt of Northeast USSR and the stage of evolution of magnetism and tectonic development of the region are examined. Recognizing the associations of effusive and intrusive rocks that are typical of the southern part of the volcanogenic belt and that are joined together by some characteristic features, a basic plan is presented for examination of the problem of magnetic formations. On the basis of the distinctive characteristics of epigeosynclinal tectonic development of the territory and the sequence of formation of the magmatic rocks within it, three main groups: volcanic, coleanoplutonic, and plutonic, can be distinguished; and a general scheme of development of these types in space and time within the volcanogenic belt can be developed. According to this scheme, four main stages can be recognized in the Mesozoic and Cenozoic magmatic evolution of the Okhotsk-Chukotka belt. This scheme of classification takes into consideration the factor of the structural development of this tectonomagmatic element.

Dynamics of the earth's radiation belts and inner magnetosphere (geophysical monograph series)

CERN Document Server

2013-01-01

Dynamics of the Earth's Radiation Belts and Inner Magnetosphere draws together current knowledge of the radiation belts prior to the launch of Radiation Belt Storm Probes (RPSP) and other imminent space missions, making this volume timely and unique. The volume will serve as a useful benchmark at this exciting and pivotal period in radiation belt research in advance of the new discoveries that the RPSP mission will surely bring. Highlights include the following: a review of the current state of the art of radiation belt science; a complete and up-to-date account of the wave-particle interactions that control the dynamical acceleration and loss processes of particles in the Earth's radiation belts and inner magnetosphere; a discussion emphasizing the importance of the cross-energy coupling of the particle populations of the radiation belts, ring current, and plasmasphere in controlling the dynamics of the inner magnetosphe...

New Quality Standards of Testing Idlers for Highly Effective Belt Conveyors

Science.gov (United States)

Król, Robert; Gladysiewicz, Lech; Kaszuba, Damian; Kisielewski, Waldemar

2017-12-01

The paper presents result of research and analyses carried out into the belt conveyors idlers’ rotational resistance which is one of the key factor indicating the quality of idlers. Moreover, idlers’ rotational resistance is important factor in total resistance to motion of belt conveyor. The evaluation of the technical condition of belt conveyor idlers is carried out in accordance with actual national and international standards which determine the methodology of measurements and acceptable values of measured idlers’ parameters. Requirements defined by the standards, which determine the suitability of idlers to a specific application, despite the development of knowledge on idlers and quality of presently manufactured idlers maintain the same level of parameters values over long periods of time. Nowadays the need to implement new, efficient and economically justified solution for belt conveyor transportation systems characterized by long routes and energy-efficiency is often discussed as one of goals in belt conveyors’ future. One of the basic conditions for achieving this goal is to use only carefully selected idlers with low rotational resistance under the full range of operational loads and high durability. Due to this it is necessary to develop new guidelines for evaluation of the technical condition of belt conveyor idlers in accordance with actual standards and perfecting of existing and development of new methods of idlers testing. The changes in particular should concern updating of values of parameters used for evaluation of the technical condition of belt conveyor idlers in relation to belt conveyors’ operational challenges and growing demands in terms of belt conveyors’ energy efficiency.

The Stability of the Conveyor Belt Pontoon

Directory of Open Access Journals (Sweden)

Jiří PODEŠVA

2011-06-01

Full Text Available To lead the conveyor belt transport cross water area the pontoon are used to support the carrying structure of the belts. The accident can happen when the pontoon turnover. For this reason the pontoon stability is investigated. The stability is described by the Reed’s diagram. This can be constructed analytically or via numerical modeling. Both methods are described in the paper.

Performance approximation of pick-to-belt orderpicking systems

NARCIS (Netherlands)

M.B.M. de Koster (René)

1994-01-01

textabstractIn this paper, an approximation method is discussed for the analysis of pick-to-belt orderpicking systems. The aim of the approximation method is to provide an instrument for obtaining rapid insight in the performance of designs of pick-to-belt orderpicking systems. It can be used to

Ambient Response Analysis of the Great Belt Bridge

DEFF Research Database (Denmark)

Brincker, Rune; Frandsen, Jeanette B.; Andersen, Palle

2000-01-01

In this paper an ambient response analysis of the Great Belt Bridge is presented. The Great Belt Bridge is one of the largest suspension bridges in the world, and the analysis was carried out in order to investigate the possibilities of estimating reliable damping values from the ambient response...

Overland conveyors. Cable or trough belt for 100 km transport haulage

Energy Technology Data Exchange (ETDEWEB)

Maton, A.E. [Maton Engineering Pty. Ltd., Orange Grove, WA (Australia)

2009-07-01

With the advances in belt conveyor technology today systems of 100 kilometres length are increasingly being considered. This article provides a comparison of two concepts for a 100 kilometre system of five 20 kilometre flights based on trough belt and cable belt technology. (orig.)

Mineralization and geochemical studies in the Kalchouyeh occurrence, southwest of Naein

Directory of Open Access Journals (Sweden)

Hengameh Hosseini Dinani

2012-10-01

Full Text Available Kalchouyeh area in southwest of Naein is located in the Urumieh-Dokhtar volcano-plutonic belt. Mineralization occurred mainly as disseminations and veinlets hosted by trachy-andesite and pyroxene andesites. For mineralogy, alteration, fluid inclusion and geochemical studies, the two major mineralized zones: A (larger vein from the north-northwest and B (smaller vein from the east-southeast of the area were sampled. Alteration studies revealed that the main alteration assemblages are silicification and propylitic. The ore minerals are chalcopyrite, galena, pyrite, bornite, chalcocite, covellite, goethite, malachite, azurite, cerussite and cuprite with quartz, calcite and barite as the main gangues. Fluid inclusion studies demonstrated that salinity and homogenization temperatures were 0.38-4.23 and 0.166-9.188 wt% NaCl and 175-252°C and 250-324°C at the A and B veins, respectively. Rare Earth Element (REE plots show negative slopes that is one of the features for calc-alkaline magmas. La/Y is higher than 1 showing that mineralizing fluids were neutral to basic. According to the data, direction of ore-bearing fluids movement was determined to be from east-southeast toward north-northwest (from B to A veins(, approximate site of mineralization center is located adjacent to smaller vein and the mineralization is epithermal in type.

Belt Conveyor Dynamic Characteristics and Influential Factors

OpenAIRE

Li, Junxia; Pang, Xiaoxu

2018-01-01

This paper uses the Kelvin-Voigt viscoelastic model to establish the continuous dynamic equations for tail hammer tension belt conveyors. The viscoelastic continuity equations are solved using the generalized coordinate method. We analyze various factors influencing longitudinal vibration of the belt conveyor by simulation and propose a control strategy to limit the vibration. The proposed approach and control strategy were verified by several experimental researches and cases. The proposed a...

2005 Southwest Florida Water Management District (SWFWMD) Lidar: Manatee District

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Light Detection and Ranging (LiDAR) LAS dataset is a survey of select areas within Southwest Florida. These data were produced for the Southwest Florida Water...

30 CFR 14.22 - Test for flame resistance of conveyor belts.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Test for flame resistance of conveyor belts. 14..., EVALUATION, AND APPROVAL OF MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS Technical Requirements § 14.22 Test for flame resistance of conveyor belts. (a) Test procedures. The test...

The thrust belts of Western North America

Energy Technology Data Exchange (ETDEWEB)

Moulton, F.C.

1993-08-01

Most of the Basin and Range physiographic province of western North America is now believed to be part of the overthrust. The more obvious overthrust belt along the eastern edge of the Basin and Range Province is named the Sevier orogenic belt, where older rocks are observed thrust onto younger rocks. More detailed surface geological mapping, plus deep multiple-fold geophysical work and many oil and gas wildcat wells, have confirmed an east-vergent shortened and stacked sequence is present in many places in the Basin and Range. This western compressive deformed area in east central Nevada is now named the Elko orogenic belt by the U.S. Geological Survey. This older compressed Elko orogenic belt started forming approximately 250 m.y. ago when the North American plate started to move west as the Pangaea supercontinent started to fragment. The North American plate moved west under the sediments of the Miogeocline that were also moving west. Surface-formed highlands and oceanic island arcs on the west edge of the North American plate restricted the westward movement of the sediments in the Miogeocline, causing east-vergent ramp thrusts to form above the westward-moving North American plate. The flat, eastward-up-cutting thrust assemblages moved on the detachment surfaces.

SLH Timing Belt Powertrain

Energy Technology Data Exchange (ETDEWEB)

Schneider, Abe

2014-04-09

The main goal of this proposal was to develop and test a novel powertrain solution for the SLH hydroEngine, a low-cost, efficient low-head hydropower technology. Nearly two-thirds of U.S. renewable electricity is produced by hydropower (EIA 2010). According to the U.S. Department of Energy; this amount could be increased by 50% with small hydropower plants, often using already-existing dams (Hall 2004). There are more than 80,000 existing dams, and of these, less than 4% generate power (Blankinship 2009). In addition, there are over 800 irrigation districts in the U.S., many with multiple, non-power, low-head drops. These existing, non-power dams and irrigation drops could be retrofitted to produce distributed, baseload, renewable energy with appropriate technology. The problem is that most existing dams are low-head, or less than 30 feet in height (Ragon 2009). Only about 2% of the available low-head hydropower resource in the U.S. has been developed, leaving more than 70 GW of annual mean potential low-head capacity untapped (Hall 2004). Natel Energy, Inc. is developing a low-head hydropower turbine that operates efficiently at heads less than 6 meters and is cost-effective for deployment across multiple low-head structures. Because of the unique racetrack-like path taken by the prime-movers in the SLH, a flexible powertrain is required. Historically, the only viable technological solution was roller chain. Despite the having the ability to easily attach blades, roller chain is characterized by significant drawbacks, including high cost, wear, and vibration from chordal action. Advanced carbon- fiber-reinforced timing belts have been recently developed which, coupled with a novel belt attachment system developed by Natel Energy, result in a large reduction in moving parts, reduced mass and cost, and elimination of chordal action for increased fatigue life. The work done in this project affirmatively addressed each of the following 3 major uncertainties concerning

Security Belt for Wireless Implantable Medical Devices.

Science.gov (United States)

Kulaç, Selman

2017-09-19

In this study, a new protective design compatible with existing non-secure systems was proposed, since it is focused on the secure communication of wireless IMD systems in all transmissions. This new protector is an external wearable device and appears to be a belt fitted around for the patients IMD implanted. However, in order to provide effective full duplex transmissions and physical layer security, some sophisticated transceiver antennas have been placed on the belt. In this approach, beam-focused multi-antennas in optimal positions on the belt are randomly switched when transmissions to the IMD are performed and multi-jammer switching with MRC combining or majority-rule based receiving techniques are applied when transmissions from the IMD are carried out. This approach can also reduce the power consumption of the IMDs and contribute to the prolongation of the IMD's battery life.

The use of seat belts and contributing factors : an international comparison.

NARCIS (Netherlands)

Mäkinen, T. Wittink, R.D. & Hagenzieker, M.P.

1991-01-01

The purpose of this study was to define factors that contribute to the use or non-use of seat belts. Legislation prescribing compulsory seat belt usage is one of the most important factors. Promotion of the use of seat belts without this legislation is very difficult and time-consuming. So far, the

Present condition of uranium exploration and the prospecting direction in southwest China

International Nuclear Information System (INIS)

Ni Shijun; Zhang Chengjiang; Xu Zhengqi; Chen Youliang

2012-01-01

Southwest China is one of the important areas where uranium is distributed. After exploration and research of 50 years, the metallogenic conditions for uranium deposits in Southwest China have been studied more deeply. It is found that uranium ore in Southwest China has more complete types, less deposits and more mineral occurrences, and the amount of uranium resources is disproportionate to the area of Southwest China. Researches of years show that Southwest China is characterized by thick crust. thick sedimentary cover, weak crust-mantle interaction, weak deep flu id activity in shallow strata, strong dynamic formation in shallow strata and obvious deep geologic process on block mar- gins. In this paper, the control of deep geologic process and evolution in uranium metallogenesis in Southwest China is studied by employing new theories and thoughts on the fundamental concept that deep geologic process and evolution has important control on super-large scale deposits. The study focuses on the crust-mantle structure and evolution with uranium metallogenesis, structural and magmatic activity and deep fluid activity with uranium metallogenesis, and ore-con- trolling role of penetrating faults on block edges and inside the blocks. To offer theoretic basis for large-scale uranium deposit prospecting in Southwest China, the key research on uranium deposit in Southwest China in future should be on the deep geologic evolution and uranium metallogenesis in Western Qinling Region, the uranium metallogenesis of iron oxide copper gold deposits on Kangdian axis, the uranium metallogenesis in Yunnan-Guizhou contiguous area, the hydrothermal uranium metallogenesis in Eastern Tibet and Western Sichuan, and the connection between sandstone type uranium deposit and magmatic activity. Meanwhile, the above regions are also the key ones for uranium deposit prospecting in Southwest China in a rather long period in future. (authors)

The evolution of Saturn's radiation belts modulated by changes in radial diffusion

Science.gov (United States)

Kollmann, P.; Roussos, E.; Kotova, A.; Paranicas, C.; Krupp, N.

2017-12-01

Globally magnetized planets, such as the Earth1 and Saturn2, are surrounded by radiation belts of protons and electrons with kinetic energies well into the million electronvolt range. The Earth's proton belt is supplied locally from galactic cosmic rays interacting with the atmosphere3, as well as from slow inward radial transport4. Its intensity shows a relationship with the solar cycle4,5 and abrupt dropouts due to geomagnetic storms6,7. Saturn's proton belts are simpler than the Earth's because cosmic rays are the principal source of energetic protons8 with virtually no contribution from inward transport, and these belts can therefore act as a prototype to understand more complex radiation belts. However, the time dependence of Saturn's proton belts had not been observed over sufficiently long timescales to test the driving mechanisms unambiguously. Here we analyse the evolution of Saturn's proton belts over a solar cycle using in-situ measurements from the Cassini Saturn orbiter and a numerical model. We find that the intensity in Saturn's proton radiation belts usually rises over time, interrupted by periods that last over a year for which the intensity is gradually dropping. These observations are inconsistent with predictions based on a modulation in the cosmic-ray source, as could be expected4,9 based on the evolution of the Earth's proton belts. We demonstrate that Saturn's intensity dropouts result instead from losses due to abrupt changes in magnetospheric radial diffusion.

Deformation and kinematics of the central Kirthar Fold Belt, Pakistan

Science.gov (United States)

Hinsch, Ralph; Hagedorn, Peter; Asmar, Chloé; Nasim, Muhammad; Aamir Rasheed, Muhammad; Kiely, James M.

2017-04-01

The Kirthar Fold Belt is part of the lateral mountain belts in Pakistan linking the Himalaya orogeny with the Makran accretionary wedge. This region is deforming very oblique/nearly parallel to the regional plate motion vector. The study area is situated between the prominent Chaman strike-slip fault in the West and the un-deformed foreland (Kirthar Foredeep/Middle Indus Basin) in the East. The Kirthar Fold Belt is subdivided into several crustal blocks/units based on structural orientation and deformation style (e.g. Kallat, Khuzdar, frontal Kirthar). This study uses newly acquired and depth-migrated 2D seismic lines, surface geology observations and Google Earth assessments to construct three balanced cross sections for the frontal part of the fold belt. Further work was done in order to insure the coherency of the built cross-sections by taking a closer look at the regional context inferred from published data, simple analogue modelling, and constructed regional sketch sections. The Khuzdar area and the frontal Kirthar Fold Belt are dominated by folding. Large thrusts with major stratigraphic repetitions are not observed. Furthermore, strike-slip faults in the Khuzdar area are scarce and not observed in the frontal Kirthar Fold Belt. The regional structural elevation rises from the foreland across the Kirthar Fold Belt towards the hinterland (Khuzdar area). These observations indicate that basement-involved deformation is present at depth. The domination of folding indicates a weak decollement below the folds (soft-linked deformation). The fold pattern in the Khuzdar area is complex, whereas the large folds of the central Kirthar Fold Belt trend SSW-NNE to N-S and are best described as large detachment folds that have been slightly uplifted by basement involved transpressive deformation underneath. Towards the foreland, the deformation is apparently more hard-linked and involves fault-propagation folding and a small triangle zone in Cretaceous sediments

76 FR 8730 - Desert Southwest Customer Service Region-Rate Order No. WAPA-151

Science.gov (United States)

2011-02-15

... DEPARTMENT OF ENERGY Western Area Power Administration Desert Southwest Customer Service Region.... Jack Murray, Rates Manager, Desert Southwest Customer Service Region, Western Area Power Administration... ancillary service rates for the Desert Southwest Customer Service Region in accordance with section 302 of...

Cranberry magnetite deposits Avery County, N.C., and Carter County, Tenn.

Science.gov (United States)

Kline, M.H.; Ballard, T.J.

1948-01-01

The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss in a belt extending from 3 miles southeast of Cranberry, N.C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve, elongated to the north, approximately 26 miles in length.

Geological characteristics of dike-structural belt in Taoshan orefield and its relationship to uranium deposits

International Nuclear Information System (INIS)

Zhang Wanliang; Zou Maoqing; Shao Fei; Nie Bin

2009-01-01

Taoshan uranium field is occurred in the Taoshan composite batholith in the central Jiangxi Province. The main body of the batholith was formed in Triassic-Early Cretaceous. In Late Cretaceous-Eogene, NE strike fault structure and dike belt were developed in the batholith. From the north to the south, there are successive Xiaobu-Matian dike-structural belt, Wangnitian dike- structural belt, Huangtan-Yueyuan dike-structural belt, Xibei-Shangluo dike-structural belt, Jipoling dike-structural belt, Wangce dike-structural belt and Shiyuanling dike-structural belt. These belts are controlled by the main fault, share the same space and similar time with the uranium mineralization, which is one of the important factors in positioning the uranium ore as well as the prospecting direction of exploration. (authors)

Belt conveyor dynamics in transient operation for speed control

NARCIS (Netherlands)

He, D.; Pang, Y.; Lodewijks, G.

2016-01-01

Belt conveyors play an important role in continuous dry bulk material transport, especially at the mining industry. Speed control is expected to reduce the energy consumption of belt conveyors. Transient operation is the operation of increasing or decreasing conveyor speed for speed control.

SEAT BELT USE AMONG CAR USERS IN MALAYSIA

Directory of Open Access Journals (Sweden)

S. KULANTHAYAN

2004-01-01

Full Text Available The car is the second (40% most common mode of transportation in Malaysia. In terms of fatal road accidents, car drivers constitute about 9.0% and passengers 13.6% of fatalities. The major cause of car occupants' fatality in such accidents is head injuries, which consist of more than half (56.4% of the fatalities. Thus restraining the head and body, the initial position is the most important injury control strategy for car users. The use of seat belts was deemed one of the most effective ways to reduce road accident fatalities in Malaysia and consequently the mandatory seat belt law was enforced in the early seventies. Therefore, a study on factors influencing the compliance behaviour of seat belt use among cars is needed as to date no such research has been undertaken in Malaysia. A questionnaire study was carried out in Selangor, Malaysia on the compliance behaviour of car occupants in relation to seat belt use. A total of 237 respondents were interviewed and the data analysed using logistic regression method. Six variables were found to be significant at 5 percent level (p<0.05: seating position, location of travel, education level, speeding, night-time driving and enforcement. Compliance with the seat belt law was higher among drivers, educated car users, in the presence of enforcement activities, travelling in city-center areas and car users with a positive attitude towards the risks of speeding and night driving.

Southwest Ecological Restoration Institutes (SWERI) Biophysical Monitoring Workshop Report

Science.gov (United States)

Joseph Seidenberg; Judy Springer; Tessa Nicolet; Mike Battaglia; Christina Vothja

2009-01-01

On October 15-16, 2009, the Southwest Ecological Restoration Institutes (SWERI) hosted a workshop in which the participants would 1) build a common understanding of the types of monitoring that are occurring in forested ecosystems of the Southwest; 2) analyze and agree on an efficient, yet robust set of biophysical variables that can be used by land mangers and...

The Stratigraphy and Lithofacies of the Paleoproterozoic Volcaniclastic Sequences in the Cape Three Points Area- Akodda section of the Southern in Ashanti Belt in the Birimian of southwest Ghana

Science.gov (United States)

Yoshimaru, S.; Kiyokawa, S.; Ito, T.; Ikehara, M.; Nyame, F. K.; Tetteh, G. M.

2015-12-01

The Paleoproterozoic Era is thought to have experienced one of the most significant changes in earth's environment during earth history. Early continents started to diverge and collide accompanied by first major oxidation of the atmosphere-oceanic system known as the Great Oxidation Environment (GOE). Due to their well-preserved oceanic sedimentary sequences, Paleoproterozoic belts are usually good targets for studies on the history of earth's past environment. In addition, these belts provide great help to understand the nature of the Paleoproterozoic deeper oceanic environments. Birimian greenstone belt in southwestern Ghana is likely to have made up of subduction of oceanic basin to form a volcanic island arc. Birimian rocks are separated by nonconformity from the Tarkwaian Group which is a younger paleoplacer deposit (Perrouty et al., 2012). The Birimian is made up of island-arc volcanic rocks; foreland basin made up of shale, sandstone, quartzite and turbidities derived from 2.17 Ga granite intrusions during Birimian volcanism. In this study, we focused on the coastal area around Cape Three Points at the southernmost part of the Ashanti (Axim-Konongo) belt in Ghana. In the eastern part of the area, excellently preserved Paleoprotorozoic deeper oceanic sedimentary sequences extensively outcrop for over 4km stretch. This volcano-sedimentary sequence has been affected by greenschist facies metamorphism. Structurally, this region preserves S1 cleavage and asymmetrical synform with west vergence and S0 younging to the east. Provisional stratigraphy is very continuous up to more than 2000m thick and, in addition, suggests at least four different fining upward sequences in the area to the east and west of Atwepo, west of Kwetakora and Akodda. These sub-sequences are mainly composed of volcaniclasitc, sandstone, black shale and rare volcanics such as pillow basalt or massive volcanic lava. In other words, this continuous sequence suggests distal submarine

International survey of seat belt use exemptions.

Science.gov (United States)

Weiss, H; Sirin, H; Levine, J A; Sauber, E

2006-08-01

Substantial evidence of seatbelt efficacy has been shown by several studies, and it is widely recommended that motor vehicle occupants use properly fitted seat belts. However, some (but a heretofore unknown number of) countries with national seat belt laws permit various exemptions which may lower use rates. The aim of this study was to survey the variety of exemptions to national seat belt laws. This investigation relied on identifying respondents from national traffic safety agencies, other governmental and non-governmental organizations, Internet searches, personal contacts, and other sources. Questionnaires were deployed through a web based survey supplemented by email and postal versions. Responses were received from 30 countries of which 28 (93.7%) had a national seat belt law. About two thirds (63.7%) of the 28 national laws applied to both front and back seat passengers. The leading exemption types included vehicles made before a certain year (n = 13), antique vehicles (n = 12), military vehicles (n = 11), buses (n = 9), and emergency vehicles (n = 8). Most responding countries reported one or more specific categories of individuals as exempt including those with medical exemptions (n = 20), taxi drivers (n = 11), police (n = 9), emergency medical personnel (n = 8), physically disabled people (n = 6), and pregnant women (n = 6). Out of 26 responses to the question regarding current level of enforcement, 42.3% felt enforcement was "very good or good" and 57.7% characterized it as "fair or poor". This study represents one of the largest international traffic law surveys reported. Most national seatbelt laws offer perilous exemptions to a broad array of vehicle types and road user groups. These findings, coupled with concern over the level of enforcement in the majority of countries surveyed, suggest that international road safety efforts have a long way to go to improve coverage and enforcement of national seat belt laws.

The Social Construction of the Great Belt Fixed Link

DEFF Research Database (Denmark)

Munch, Birgitte

1994-01-01

Working paper in Technology Management. Actor Network theory (ANT) used upon the process of negotiating legislation and constructing the Great Belt fixed link.......Working paper in Technology Management. Actor Network theory (ANT) used upon the process of negotiating legislation and constructing the Great Belt fixed link....

Paired Magmatic-Metallogenic Belts in Myanmar - an Andean Analogue?

Science.gov (United States)

Gardiner, Nicholas; Robb, Laurence; Searle, Michael; Morley, Christopher

2015-04-01

Myanmar (Burma) is richly endowed in precious and base metals, having one of the most diverse collections of natural resources in SE Asia. Its geological history is dominated by the staged closing of Tethys and the suturing of Gondwana-derived continental fragments onto the South China craton during the Mesozoic-Cenozoic. The country is located at a crucial geologic juncture where the main convergent Tethyan collision zone swings south around the Namche Barwa Eastern Himalayan syntaxis. However, despite recent work, the geological and geodynamic history of Myanmar remains enigmatic. Plate margin processes, magmatism, metasomatism and the genesis of mineral deposits are intricately linked, and there has long been recognized a relationship between the distribution of certain mineral deposit types, and the tectonic settings which favour their genesis. A better knowledge of the regional tectonic evolution of a potential exploration jurisdiction is therefore crucial to understanding its minerals prospectivity. This strong association between tectonics and mineralization can equally be applied in reverse. By mapping out the spatial, and temporal, distribution of presumed co-genetic mineral deposits, coupled with an understanding of their collective metallogenetic origin, a better appreciation of the tectonic evolution of a terrane may be elucidated. Identification and categorization of metallotects within a geodynamically-evolving terrane thus provides a complimentary tool to other methodologies (e.g. geochemical, geochronological, structural, geophysical, stratigraphical), for determining the tectonic history and inferred geodynamic setting of that terrane through time. Myanmar is one such study area where this approach can be undertaken. Here are found two near-parallel magmatic belts, which together contain a significant proportion of that country's mineral wealth of tin, tungsten, copper, gold and silver. Although only a few 100 km's apart, these belts exhibit a

Type QH-200 conveyor-belt nuclear scale

International Nuclear Information System (INIS)

Li Shuming; Dong Shiyuan; Li Furong; Wan Zemin

1991-01-01

Type QH-200 conveyor-belt nuclear scale is a reliable and on-line device that weighs solids mass flow continuously by γ-ray absorption and scattering. The operation principle and measuring method are described. And some factors influencing the accuracy are discussed. The full scale total weight of type QH-200 nuclear scale is 10 6 t. The result of calibration in the industrial field shows that the accuracy of QH-200 is better than ±1.0% for typical belt loading

The Sino-American belt study: nickel and cobalt exposure, epidemiology, and clinical considerations.

Science.gov (United States)

Hamann, Dathan; Hamann, Carsten; Li, Lin-Feng; Xiang, Hailian; Hamann, Kylin; Maibach, Howard; Taylor, James S; Thyssen, Jacob P

2012-01-01

Nickel and cobalt are common causes of metal allergy. The objective of this study was to investigate nickel and cobalt exposure in belt buckles by testing 701 belts purchased in China and the United States and to consider the prevalence of nickel allergy and its relevance among Chinese patients. Seven hundred one belt buckles purchased in China and the United States were tested for nickel and cobalt release. Six hundred thirty-one Chinese patients with suspected allergic contact dermatitis were patch tested and interviewed to determine clinical relevance of results. The Chinese and American literature was reviewed to investigate trends in nickel prevalence over the past decades. Sixty percent (n = 219) of belts purchased in China (n = 365) released nickel, and 0.5% (n = 2) released cobalt; 55.7% (n = 187) in the United States (n = 336) released nickel, and 0.9% (n = 3) released cobalt. Belt dermatitis was a significant clinical finding in 34.8% of Chinese nickel-allergic patients. Literature review suggests increasing nickel allergy prevalence in the United States and China. Metallic belt buckles are an important source of nickel exposure to consumers. Belts from lowest socioeconomic vendors were more likely to release nickel. Belts with silver color and dark metallic color were more likely to release nickel and cobalt, respectively. Clinical findings show belt dermatitis in China to be a problem.

The physical imitation experiments of nuclear belt weight scaler

International Nuclear Information System (INIS)

Shi Qicun; Wang Mingqian; Sun Jinhua; Li Zhonghao

1993-01-01

The physical imitation experiments of the nuclear belt weight scaler (NBWS) were performed with a coal-loaded belt. The linearity, repetition and long-time stability; of the NBWS were measured. And the influence of pile shape, load bias and the composition of coal on weight calculation were studied

Variability in measured current structure on the southwest continental shelf of India

Digital Repository Service at National Institute of Oceanography (India)

DineshKumar, P.K.; Srinivas, K.

-1 Variability in Measured Current Structure on the Southwest Continental Shelf of India P.K. Dinesh Kumar and K. Srinivas National Institute of Oceanography, Regional Centre P.O.Box 1913, Cochin - 682018,India Email: dineshku@niokochi.org ABSTRACT... WORDS: Direct current measurements, tidal currents, southwest coast of India. INTRODUCTION The circulation pattern of the eastern Arabian Sea over the southwest continental shelf of India (inferred...

Structural appraisal of the Gadag schist belt from gravity investigations

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

From qualitative analysis of the gravity data, several tectonic features are ... major types of schist belts are identified in the ... Dharwar craton; Gadag schist belt; gravity method; inversion. ..... the Research Associateship of Dr D Himabindu.

Understanding quaternions and the Dirac belt trick

International Nuclear Information System (INIS)

Staley, Mark

2010-01-01

The Dirac belt trick is often employed in physics classrooms to show that a 2π rotation is not topologically equivalent to the absence of rotation whereas a 4π rotation is, mirroring a key property of quaternions and their isomorphic cousins, spinors. The belt trick can leave the student wondering if a real understanding of quaternions and spinors has been achieved, or if the trick is just an amusing analogy. The goal of this paper is to demystify the belt trick and to show that it suggests an underlying four-dimensional parameter space for rotations that is simply connected. An investigation into the geometry of this four-dimensional space leads directly to the system of quaternions, and to an interpretation of three-dimensional vectors as the generators of rotations in this larger four-dimensional world. The paper also shows why quaternions are the natural extension of complex numbers to four dimensions. The level of the paper is suitable for undergraduate students of physics.

Large enhancement of highly energetic electrons in the outer radiation belt and its transport into the inner radiation belt inferred from MDS-1 satellite observations

Science.gov (United States)

Obara, T.; Matsumoto, H.

2016-03-01

We have examined a large increase of relativistic electrons in the outer radiation belt and its penetration into the inner radiation belt over slot region using the MDS-1 satellite observations. Result of analyses demonstrates that a large increase took place in the spring and autumn seasons, and we have newly confirmed that the penetration of outer belt electrons to the inner radiation zone took place during the big magnetic storms by examining a pitch angle distribution of the penetrating electrons.

Aortic ruptures in seat belt wearers.

Science.gov (United States)

Arajärvi, E; Santavirta, S; Tolonen, J

1989-09-01

Several investigations have indicated that rupture of the thoracic aorta is one of the leading causes of immediate death in victims of road traffic accidents. In Finland in 1983, 92% of front-seat passengers were seat belt wearers on highways and 82% in build-up areas. The mechanisms of rupture of the aorta have been intensively investigated, but the relationship between seat belt wearing and injury mechanisms leading to aortic rupture is still largely unknown. This study comprises 4169 fatally injured victims investigated by the Boards of Traffic Accident Investigation of Insurance Companies during the period 1972 to 1985. Chest injuries were recorded as the main cause of death in 1121 (26.9%) victims, 207 (5.0%) of those victims having worn a seat belt. Aortic ruptures were found at autopsy in 98 victims and the exact information of the location of the aortic tears was available in 68. For a control group, we analyzed 72 randomly chosen unbelted victims who had a fatal aortic rupture in similar accidents. The location of the aortic rupture in unbelted victims was more often in the ascending aorta, especially in drivers, whereas in seat belt wearers the distal descending aorta was statistically more often ruptured, especially in right-front passengers (p less than 0.05). The steering wheel predominated statistically as the part of the car estimated to have caused the injury in unbelted victims (37/72), and some interior part of the car was the most common cause of fatal thoracic impacts in seat belt wearers (48/68) (p less than 0.001). The mechanism of rupture of the aorta in the classic site just distal to the subclavian artery seems to be rapid deceleration, although complex body movements are also responsible in side impact collisions. The main mechanism leading to rupture of the ascending aorta seems to be severe blow to the bony thorax. This also often causes associated thoracic injuries, such as heart rupture and sternal fracture. Injuries in the ascending

The Belt voice: Acoustical measurements and esthetic correlates

Science.gov (United States)

Bounous, Barry Urban

This dissertation explores the esthetic attributes of the Belt voice through spectral acoustical analysis. The process of understanding the nature and safe practice of Belt is just beginning, whereas the understanding of classical singing is well established. The unique nature of the Belt sound provides difficulties for voice teachers attempting to evaluate the quality and appropriateness of a particular sound or performance. This study attempts to provide answers to the question "does Belt conform to a set of measurable esthetic standards?" In answering this question, this paper expands on a previous study of the esthetic attributes of the classical baritone voice (see "Vocal Beauty", NATS Journal 51,1) which also drew some tentative conclusions about the Belt voice but which had an inadequate sample pool of subjects from which to draw. Further, this study demonstrates that it is possible to scientifically investigate the realm of musical esthetics in the singing voice. It is possible to go beyond the "a trained voice compared to an untrained voice" paradigm when evaluating quantitative vocal parameters and actually investigate what truly beautiful voices do. There are functions of sound energy (measured in dB) transference which may affect the nervous system in predictable ways and which can be measured and associated with esthetics. This study does not show consistency in measurements for absolute beauty (taste) even among belt teachers and researchers but does show some markers with varying degrees of importance which may point to a difference between our cognitive learned response to singing and our emotional, more visceral response to sounds. The markers which are significant in determining vocal beauty are: (1) Vibrancy-Characteristics of vibrato including speed, width, and consistency (low variability). (2) Spectral makeup-Ratio of partial strength above the fundamental to the fundamental. (3) Activity of the voice-The quantity of energy being produced. (4

Phytomass in southwest Alaska.

Science.gov (United States)

Bert R. Mead

2000-01-01

Phytomass tables are presented for southwest Alaska. The methods used to estimate plant weight and occurrence in the river basin are described and discussed. Average weight is shown for each sampled species of tree, shrub, grass, forb, lichen, and moss in 19 forest and 48 nonforest vegetation types. Species frequency of occurrence and species constancy within the type...

Geological and geochemical characteristics of the Heerenveen and Mpuluzi batholiths south of the Barberton greenstone belt and preliminary thoughts on their petrogenesis

International Nuclear Information System (INIS)

Anhaeusser, C.R.; Robb, L.J.

1982-01-01

The Archaean granitic terrane south and south-west of the Barberton greenstone belt consists predominantly of an older suite of tonalitic and trondhjemitic gneisses into which have been emplaced two large multi-component granitoid bodies known as the Heerenveen and Mpuluzi batholiths. Although geochronologic and Sr-isotopic studies demonstrate that there is little distinction between the ages and initial ratios of the various phases associated with these batholiths, each body displays contrasting textural and geochemical characteristics. The oldest phase is represented by coarse porphyritic granitic rocks into which is intruded a medium-to-fine-grained homogeneous granodioritic phase. Both phases are components of a bimodal association that is, in turn, intruded by a third phase which includes medium-grained pink or grey granodiorite and adamellite dykes feeding a homogeneous sheet-like carapace over-lying the coarser porphyritic granites. A fourth phase, consisting predominantly of potassic migmatites and gneisses, occurs in the areas rimming the batholiths and represents the product of interaction between the batholith magmas and components of the pre-existing crust in the region. Geochemically, the Heerenveen batholith has trondhjemitic affinities whereas the Mpuluzi batholith consists predominantly of potassic granites. Together with the Nelspruit batholith north of the Barberton greenstone belt the three granitic bodies show a progression in actual values of K 2 O, Na 2 O, Rb, and Sr with the Nelspruit body having chemical characteristics intermediate between the two

2005 Southwest Florida Water Management District (SWFWMD) Lidar: Little Manatee District

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Light Detection and Ranging (LiDAR) LAS dataset is a survey of select areas within Southwest Florida. These data were produced for the Southwest Florida Water...

Bouguer gravity trends and crustal structure of the Palmyride Mountain belt and surrounding northern Arabian platform in Syria

Science.gov (United States)

Best, John A.; Barazangi, Muawia; Al-Saad, Damen; Sawaf, Tarif; Gebran, Ali

1990-12-01

This study examines the crustal structure of the Palmyrides and the northern Arabian platform in Syria by two- and three-dimensional modeling of the Bouguer gravity anomalies. Results of the gravity modeling indicate that (1) western Syria is composed of at least two different crustal blocks, (2) the southern crustal block is penetrated by a series of crustal-scale, high-density intrusive complexes, and (3) short-wavelength gravity anomalies in the southwest part of the mountain belt are clearly related to basement structure. The crustal thickness in Syria, as modeled on the gravity profiles, is approximately 40 ±4 km, which is similar to crustal thicknesses interpreted from refraction data in Jordan and Saudi Arabia. The different crustal blocks and large-scale mafic intrusions are best explained, though not uniquely, by Proterozoic convergence and suturing and early Paleozoic rifting, as interpreted in the exposed rocks of the Arabian shield. These two processes, combined with documented Mesozoic rifting and Cenozoic transpression, compose the crustal evolution of the northern Arabian platform beneath Syria.

Bouguer gravity trends and crustal structure of the Palmyride Mountain belt and surrounding northern Arabian platform in Syria

Energy Technology Data Exchange (ETDEWEB)

Best, J.A.; Barazangi, M. (Cornell Univ., Ithaca, NY (USA)); Al-Saad, D.; Sawaf, T.; Gebran, A. (Syrian Petroleum Company, Damascus (Syria))

1990-12-01

This study examines the crustal structure of the Palmyrides and the northern Arabian platform in Syria by two- and three-dimensional modeling of the Bouguer gravity anomalies. Results of the gravity modeling indicate that (1) western Syria is composed of at least two different crustal blocks, (2) the southern crustal block is penetrated by a series of crustal-scale, high-density intrusive complexes, and (3) short-wavelength gravity anomalies in the southwest part of the mountain belt are clearly related to basement structure. The crustal thickness in Syria, as modeled on the gravity profiles, is approximately 40{plus minus}4 km, which is similar to crustal thicknesses interpreted from refraction data in Jordan and Saudi Arabia. The different crustal blocks and large-scale mafic intrusions are best explained, though not uniquely, by Proterozoic convergence and suturing and early Paleozoic rifting, as interpreted in the exposed rocks of the Arabian shield. These two processes, combined with documented Mesozoic rifting and Cenozoic transpression, compose the crustal evolution of the northern Arabian platform beneath Syria.

Monitoring, Analyzing and Assessing Radiation Belt Loss and Energization

Science.gov (United States)

Daglis, I.; Balasis, G.; Bourdarie, S.; Horne, R.; Khotyaintsev, Y.; Mann, I.; Santolik, O.; Turner, D.; Anastasiadis, A.; Georgiou, M.; Giannakis, O.; Papadimitriou, C.; Ropokis, G.; Sandberg, I.; Angelopoulos, V.; Glauert, S.; Grison, B., Kersten T.; Kolmasova, I.; Lazaro, D.; Mella, M.; Ozeke, L.; Usanova, M.

2013-09-01

We present the concept, objectives and expected impact of the MAARBLE (Monitoring, Analyzing and Assessing Radiation Belt Loss and Energization) project, which is being implemented by a consortium of seven institutions (five European, one Canadian and one US) with support from the European Community's Seventh Framework Programme. The MAARBLE project employs multi-spacecraft monitoring of the geospace environment, complemented by ground-based monitoring, in order to analyze and assess the physical mechanisms leading to radiation belt particle energization and loss. Particular attention is paid to the role of ULF/VLF waves. A database containing properties of the waves is being created and will be made available to the scientific community. Based on the wave database, a statistical model of the wave activity dependent on the level of geomagnetic activity, solar wind forcing, and magnetospheric region will be developed. Multi-spacecraft particle measurements will be incorporated into data assimilation tools, leading to new understanding of the causal relationships between ULF/VLF waves and radiation belt dynamics. Data assimilation techniques have been proven as a valuable tool in the field of radiation belts, able to guide 'the best' estimate of the state of a complex system. The MAARBLE (Monitoring, Analyzing and Assessing Radiation Belt Energization and Loss) collaborative research project has received funding from the European Union’s Seventh Framework Programme (FP7-SPACE-2011-1) under grant agreement no. 284520.

On the existence of a comet belt beyond Neptune

International Nuclear Information System (INIS)

Fernandez, J.A.

1980-01-01

The possible existence of a comet belt in connection with the origin of the short-period comets is analysed. It is noted that the current theory - that these comets originate as near-parabolic comets captured by Jupiter and the other giant planets - implies an excessive wastage of comets lost in hyperbolic orbits, which is avoided in the present model. The following picture is predicted. Solid conglomerates up to approximately 10 18 g were formed by gravitational instabilities in the belt region (about 35 to 50 AU). A further fragmentation-accretion process led to a power-law mass distribution similar to that observed in the asteroids. Since then, close encounters between members of the belt have provoked the diffusion of some of them with the effect that they have become subject to the strong perturbations of Neptune. Of these a small number pass from one planet to the next inside and end as short-period comets. By means of a Monte Carlo method, the influence of close encounters between belt comets is then studied in relation to the diffusion of their orbits. It is concluded that if such a belt contains members with masses equal to or greater than that of Ceres, the orbital diffusion could proceed fast enough to maintain the number of observed short-period comets in a steady state. (author)

Clay mineral distribution and provenance in the Heuksan mud belt, Yellow Sea

Science.gov (United States)

Cho, Hyen Goo; Kim, Soon-Oh; Kwak, Kyeong Yoon; Choi, Hunsoo; Khim, Boo-Keun

2015-12-01

The Heuksan mud belt (HMB), located in the southeastern Yellow Sea, runs parallel to the southwest coast of Korea. In this study, the distribution and relative contribution of four major clay minerals are investigated using 101 surface sediment samples collected in the course of KIOST (2001, 2010, 2011) and KIGAM (2012) cruises, as well as 33 river sediment samples (four from the Huanghe River, three from the Changjiang River, and 26 from Korean rivers) in order to clarify the provenance of fine-grained sediments in the HMB. Based on this currently largest and most robust dataset available for interpretation, the clay mineral assemblages of the fine-grained sediments in the HMB are found to be on average composed of 64.7% illite, 17.9% chlorite, 11.4% kaolinite, and 5.9% smectite. Overall, the clay mineral assemblages are similar in both the northern and the southern parts of the HMB, although smectite seems to be relatively enriched in the southern part, whereas kaolinite is slightly more dominant in the northern part. This clearly indicates that the clays are mostly derived from Korean rivers and, in the southern part of the HMB, partly also from the Huanghe River in China. The new data thus confirm and strengthen the tentative interpretation of some earlier work based on a more limited dataset.

Southwest Asia assessment.

Science.gov (United States)

Devendra, T

1984-06-01

Southwest Asia, which support 1/3 of the world's population, is acutely aware of the consequences of rapid and excessive population growth. No other region has consciously devoted so much of its resources to stemming excessive population growth. India, with a population of 684 million, formulated a policy of population limitation in the 1950s. The 1980 government rededicated itself to voluntary family planning and rebuilt the broad coalition of an excellent infrastructure of government institutions, voluntary organizations, and international agencies. Government support for family planning clinics began in Bangladesh in the 1960s. A strong institutional structure has been established under the supervision of the National Population Council. Innovative approaches to family planning service delivery have been initiated by an admirable array of institutions. Pakistan's Population Welfare Plan provides substantial funds and an administrative structure to make maternal/child helath care and family planning services available in rural areas. Another welfare program encourages smaller families through projects to enhance the status of women by improving literacy, establishing rural industries, and advocating late marriage. Nepal has had to struggle with a poor administrative structure, grossly insufficient medical services, and an inadequate database for policy formulation. Family planning services are now a component of the overall health program. The family planning services of the pioneer Afghan Family Guidance Association, established in 1968, have been incorported into the national maternal/child health program. The present government of Iran views foreign assistance as an unacceptable form of persuasion and has phased out all international funded family planning programs. Sri Lanka is the only country in the region to have made the demographic transition to fertility decline. An impressive health infrastructure delivers family planning services at every level using

Effects of a Belt on Intra-Abdominal Pressure during Weight Lifting.

Science.gov (United States)

1988-03-01

potentially injurious b compressive forces on spinal discs during lifting. To investigate the effects of a standard lifting belt on lAP and lifting mechanics... injurious compressive forces on spinal discs during lifting. To investigate the effects of a standard lifting belt on IAP and lifting ! mechanics... weightlifting (7,9). Both olympic and power lifters have used lifting belts for many years, yet virtually no research has been reported which examines

The Valle de Bravo Volcanic Field. A monogenetic field in the central front of the Mexican Volcanic Belt

Science.gov (United States)

Aguirre-Diaz, G. J.; Jaimes-Viera, M. D.; Nieto-Obreg¢n, J.; Lozano-Santacruz, R.

2003-12-01

The Valle de Bravo volcanic field, VBVF, is located in the central-southern front of the Mexican Volcanic Belt just to the southwest of Nevado de Toluca volcano. The VBVF covers 3,703 square Km and includes at least 122 cinder cones, 1 shield volcano, several domes, and the 2 volcanic complexes of Zitacuaro and Villa de Allende. Morphometric parameters calibrated with isotopic ages of the volcanic products indicate four groups or units for the VBVF, Pliocene domes and lava flows, undifferentiated Pleistocene lava flows,> 40 Ka cones and lavas, 40 to 25 Ka cones and lavas, 25 to 10 Ka cones and lavas, and < 10 Ka cones and lavas. Whole-rock chemistry shows that all products of the VBVF range from basaltic andesites to dacites. No basalts were found, in spite of many units are olivine-rich and large some with large weight percent contents of MgO, 1 to 9. There is the possibility that some or all of the olivines in some samples could be xenocrysts. Some andesites are high in Sr, 1000 to 1800 ppm, that correlates with relatively high values of Ba, Cr, Ni, Cu, CaO and MgO. Y and Nb have the typical low values for orogenic rocks. The only shield volcano of the VBVF has a base of 9 Km, and its composition is practically the average composition of the whole field. Stratigraphycally, it is one of the earlier events of the VBVF. Compared with other volcanic fields of the Mexican Volcanic Belt, it lacks basalts and alkalic rocks. All volcanism of this field is calcalkaline

Major geological events and uranium metallogenesis in South-west China

International Nuclear Information System (INIS)

Zhang Chengjiang; Xu Zhengqi; Ni Shijun; Chen Youliang

2012-01-01

Uranium is widely distributed in South-west China, with all types but on a not-so-large scale. South-west China is located on the combining site of several large tectonic elements and every tectonic movement has different effects on different regions. To study and clarify the correlation between the major geological events in South-west China and the Uranium metallogenesis, comprehensive research and field investigation are made besides collecting a lot of materials. Through analysis and research on the major geological events in South-west China, the evolution of those e vents is basically clarified and the events closely related with uranium mineralization are determined. It is discovered that there are several ore-forming geologic events in the geological history of South-west China; almost every major tectonic movement cycle is accompanied with uranium metallogenesis, from Jinning Movement to Chengjiang Movement, to Hercynian Movement, to Indosinian Movement. to Yanshan Movement. to Himalayan movement. Even though every major tectonic cycle is accompanied with uranium mineralization, three major geological events are generally obviously related with uranium metallogenesis, i.e. the Rodinian supercontinent breakup even in Jinning-Chengjiang Period, Yanshan Movement and Himalayan movement, in which the first one is the process of uranium pre-enrichment and provides the source of uranium. Yanshan Movement and Himalayan movement are the important processes for mineralization, mainly the hydrothermal superimposed mineralization. (authors)

Metallogenic epoch of the Jiapigou gold belt, Jilin Province, China

Indian Academy of Sciences (India)

Metallogenic epoch of the Jiapigou gold belt, Jilin Province, China: ... The Jiapigou gold belt is located on the northern margin of the North China Craton, and is one of the ... 29, Xueyuan Road, Beijing 100083, People's Republic of China.

Electron Radiation Belts of the Solar System

Science.gov (United States)

Mauk, Barry; Fox, Nicola

To address the question of what factors dictate similarities and differences between radiation belts, we present comparisons between the electron radiation belt spectra of all five strongly magnetized planets within the solar system: Earth, Jupiter, Saturn, Uranus, and Neptune. We choose the highest intensity observed electron spectrum within each system (highest specifically near 1 MeV) and compare them against expectations based on the so-called Kennel-Petschek limit (KP; 1966) for each system. For evaluating the KP limit, we begin with the new relativis-tically correct formulation of Summers et al. (2009) but then add several refinements of our own. Specifically, we: 1) utilized a much more flexible analytic spectral shape that allows us to accurately fit observed radiation belt spectra; 2) adopt the point of view that the anisotropy parameter is not a free parameter but must take on a minimal value, as originally proposed by Kennel and Petschek (1966); and 3) examine the differential characteristics of the KP limit along the lines of what Schulz and Davidson (1988) performed for the non-relativistic formula-tion. We find that three factors limit the highest electron radiation belt intensities within solar system planetary magnetospheres: a) whistler mode interactions that limit spectral intensities to a differential Kennel-Petschek limit (3 planets); b) the absence of robust acceleration pro-cesses associated with injection dynamics (1 planet); and c) material interactions between the radiation particles and clouds of gas and dust (1 planet).

Conceptual design of a Moving Belt Radiator (MBR) shuttle-attached experiment

Science.gov (United States)

Aguilar, Jerry L.

1990-01-01

The conceptual design of a shuttle-attached Moving Belt Radiator (MBR) experiment is presented. The MBR is an advanced radiator concept in which a rotating belt is used to radiate thermal energy to space. The experiment is developed with the primary focus being the verification of the dynamic characteristics of a rotating belt with a secondary objective of proving the thermal and sealing aspects in a reduced gravity, vacuum environment. The mechanical design, selection of the belt material and working fluid, a preliminary test plan, and program plan are presented. The strategy used for selecting the basic sizes and materials of the components are discussed. Shuttle and crew member requirements are presented with some options for increasing or decreasing the demands on the STS. An STS carrier and the criteria used in the selection process are presented. The proposed carrier for the Moving Belt Radiator experiment is the Hitchhiker-M. Safety issues are also listed with possible results. This experiment is designed so that a belt can be deployed, run at steady state conditions, run with dynamic perturbations imposed, verify the operation of the interface heat exchanger and seals, and finally be retracted into a stowed position for transport back to earth.

Design study of flat belt CVT for electric vehicles

Science.gov (United States)

Kumm, E. L.

1980-01-01

A continuously variable transmission (CVT) was studied, using a novel flat belt pulley arrangement which couples the high speed output shaft of an energy storage flywheel to the drive train of an electric vehicle. A specific CVT arrangement was recommended and its components were selected and sized, based on the design requirements of a 1700 KG vehicle. A design layout was prepared and engineering calculations made of component efficiencies and operating life. The transmission efficiency was calculated to be significantly over 90% with the expected vehicle operation. A design consistent with automotive practice for low future production costs was considered, together with maintainability. The technology advancements required to develop the flat belt CVT were identified and an estimate was made of how the size of the flat belt CVT scales to larger and smaller design output torques. The suitability of the flat belt CVT for alternate application to an electric vehicle powered by an electric motor without flywheel and to a hybrid electric vehicle powered by an electric motor with an internal combustion engine was studied.

Race, belief in destiny, and seat belt usage: a pilot study.

Science.gov (United States)

Colón, I

1992-01-01

A survey of 1063 individuals found that when belief in destiny was statistically controlled, differences in seat belt use by race disappeared. Thus, racial differences in seat belt use are statistically accounted for and might be explained by belief in destiny. Efforts to increase seat belt use should target minority groups rather than include them in broadbrush programs. Further, these efforts should take into account this important difference in motivation. PMID:1585969

Politics-Administration Interface and Sustenance of Public Service Ethos in South-West Nigeria

Directory of Open Access Journals (Sweden)

Salami Issa Afegbua

2016-03-01

Full Text Available This work examined politics-administration interface and the sustenance of public service ethos in Southwest Nigeria. Public servants and political functionaries in Southwest Nigeria are constantly in a struggle to fix each other in their pre-conceived mould of mental judgment which invariably breeds mutual suspicion, apprehension and setting the stage for conflict which is likely to impact negatively on the performance of public servants in Southwest Nigeria. The article identified the factors influencing the interface of public servants and political office holders in Southwest Nigeria. It also determined the influence of the interface between on public service ethos and finally examined the efforts made towards sustaining public service ethos in Southwest Nigeria. In carrying out this work, primary and secondary data were used. In the case of primary data, survey was carried out and questionnaire was used to elicit information from respondents in the Southwest geo-political zone of the country. Purposive random sampling techniques were adopted to determine the target respondents. The study has a sample of five hundred and thirty-five (535, which constitute 50 percent of the total population figure of 1070.  The findings revealed amongst others, that the synergy between political functionaries and public office holders is often characterized by both conflict and cooperation. In addition, there are certain factors influencing the interface of public servants and political office holders in Southwest Nigeria, these factors include: contract awards, consideration in the appointment of top civil servants etc. The study therefore, recommends the need for Southwest Nigeria to strengthen politics-administration interface in such a way that the public services in that region will be more productive. There is also the need for government in the Southwest to clarify the respective roles of political office holders and public servants. The principles

A minimalistic and optimized conveyor belt for neutral atoms.

Science.gov (United States)

Roy, Ritayan; Condylis, Paul C; Prakash, Vindhiya; Sahagun, Daniel; Hessmo, Björn

2017-10-20

Here we report of a design and the performance of an optimized micro-fabricated conveyor belt for precise and adiabatic transportation of cold atoms. A theoretical model is presented to determine optimal currents in conductors used for the transportation. We experimentally demonstrate a fast adiabatic transportation of Rubidium ( 87 Rb) cold atoms with minimal loss and heating with as few as three conveyor belt conductors. This novel design of a multilayered conveyor belt structure is fabricated in aluminium nitride (AlN) because of its outstanding thermal and electrical properties. This demonstration would pave a way for a compact and portable quantum device required for quantum information processing and sensors, where precise positioning of cold atoms is desirable.

Design of a nucleonic conveyor belt weighing machine

International Nuclear Information System (INIS)

Magal, B.S.; Sunder Singh, V.P.

1979-01-01

A brief literature survey of the existing conventional units and the nucleonic belt weigher is made. The design of a 250 ton per hour coal weighing unit working in conjunction with a 24 inch wide belt, running at 350 feet per minute has been attempted and a unit has been built to the above specifications. Caseium-137 line source has been used as an isotope and a 10 litre volume argon filled ionisation chamber has been used as a detector. A line source has been preferred to a point source. The unit is under trial and the accuracy of the same is being evaluated by changing the variables like particle size profile of the material deposited on the belt and sudden changes in loading. Initial trials indicate that an accuracy of +- 1 p.c. can be achieved. (auth.)

Fiscal Year 2013 Comprehensive Oversight Plan for Southwest Asia

Science.gov (United States)

2012-09-26

exclusively a Southwest Asia country. Source: International Organization for Standardization, ISO 3166-1-Alpha-2 Country Codes. FY 2013 COPSWA...the Continental U.S. Other/Multiple = Not exclusively a Southwest Asia country. Source: International Organization for Standardization, ISO 3166-1...rolling stock  R4D of equipment and supplies  R4D of medical equipment and supplies (including hazmat and pharmacy items)  Readiness of the Army

Knowledge, attitude and use of seat belt among commercial drivers in Sokoto Metropolis

Directory of Open Access Journals (Sweden)

A O Abiola

2010-01-01

Conclusion: This study has identified high level of knowledge, positive attitude and reported use of seat belt. It is recommended that public awareness of the safety benefits of seat belts and strong enforcement are necessary to achieve optimal use of seat belt.

A multi points ultrasonic detection method for material flow of belt conveyor

Science.gov (United States)

Zhang, Li; He, Rongjun

2018-03-01

For big detection error of single point ultrasonic ranging technology used in material flow detection of belt conveyor when coal distributes unevenly or is large, a material flow detection method of belt conveyor is designed based on multi points ultrasonic counter ranging technology. The method can calculate approximate sectional area of material by locating multi points on surfaces of material and belt, in order to get material flow according to running speed of belt conveyor. The test results show that the method has smaller detection error than single point ultrasonic ranging technology under the condition of big coal with uneven distribution.

The behavioral impact of an advertising campaign to promote safety belt use.

Science.gov (United States)

Cope, J G; Moy, S S; Grossnickle, W F

1988-01-01

Safety belt use was observed at one restaurant during McDonald's "Make It Click" promotional campaign. Following baseline, the program was monitored without intervention. During the final 2 weeks of the campaign an incentive strategy was added providing a large soft drink contingent on safety belt use. Safety belt use did not change from baseline levels before the incentive phase. The rate of belt use increased under contingent reward and declined during follow-up. The effects of a verbal prompt could not be assessed because of the almost nonexistent use of the "Make It Click" stickers throughout the study.

Study on Fuzzy Comprehensive Evaluation Model for the Safety of Mine Belt Conveyor

Directory of Open Access Journals (Sweden)

Gong Xiaoyan

2017-01-01

Full Text Available To improve the situation of the frequent failures of mine belt conveyor during operation, a model was used to evaluate the safety of mine belt conveyor. Based on the foundation of collecting and analyzing a large quantity of fault information of belt conveyor in the nationwide coal mine, the fault tree model of belt conveyor has been built, then the safety evaluation index system was established by analyzing and removing some secondary indicators. Furthermore, the weighted value of safety evaluation indexs was determined by analytic hierarchy process(AHP, and the single factor fuzzy evaluation matrix was constructed by experts grading method. Additionally, the model was applied in evaluating the security of belt conveyor in Nanliang coal mine. The results shows the security level is recognized to the “general”, which means that this model can be adopted widely in evaluating the safety of mine belt conveyor.

Does unbelted safety requirement affect protection for belted occupants?

Science.gov (United States)

Hu, Jingwen; Klinich, Kathleen D; Manary, Miriam A; Flannagan, Carol A C; Narayanaswamy, Prabha; Reed, Matthew P; Andreen, Margaret; Neal, Mark; Lin, Chin-Hsu

2017-05-29

Federal regulations in the United States require vehicles to meet occupant performance requirements with unbelted test dummies. Removing the test requirements with unbelted occupants might encourage the deployment of seat belt interlocks and allow restraint optimization to focus on belted occupants. The objective of this study is to compare the performance of restraint systems optimized for belted-only occupants with those optimized for both belted and unbelted occupants using computer simulations and field crash data analyses. In this study, 2 validated finite element (FE) vehicle/occupant models (a midsize sedan and a midsize SUV) were selected. Restraint design optimizations under standardized crash conditions (U.S.-NCAP and FMVSS 208) with and without unbelted requirements were conducted using Hybrid III (HIII) small female and midsize male anthropomorphic test devices (ATDs) in both vehicles on both driver and right front passenger positions. A total of 10 to 12 design parameters were varied in each optimization using a combination of response surface method (RSM) and genetic algorithm. To evaluate the field performance of restraints optimized with and without unbelted requirements, 55 frontal crash conditions covering a greater variety of crash types than those in the standardized crashes were selected. A total of 1,760 FE simulations were conducted for the field performance evaluation. Frontal crashes in the NASS-CDS database from 2002 to 2012 were used to develop injury risk curves and to provide the baseline performance of current restraint system and estimate the injury risk change by removing the unbelted requirement. Unbelted requirements do not affect the optimal seat belt and airbag design parameters in 3 out of 4 vehicle/occupant position conditions, except for the SUV passenger side. Overall, compared to the optimal designs with unbelted requirements, optimal designs without unbelted requirements generated the same or lower total injury risks for

40 CFR 81.23 - Southwest Pennsylvania Intrastate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Region. 81.23 Section 81.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.23 Southwest Pennsylvania Intrastate Air Quality Control Region. The Southwest Pennsylvania Intrastate Air Quality Control Region is redesignated to consist of the territorial...

An evaluation of a weightlifting belt and back injury prevention training class for airline baggage handlers.

Science.gov (United States)

Reddell, C R; Congleton, J J; Dale Huchingson, R; Montgomery, J F

1992-10-01

This study evaluated the efficacy of a commercially available weightlifting belt in relation to reduction of lumbar injury incident rate and severity of injuries over an 8-month period. The study used 642 baggage handlers working for a major airline company as participants. Four treatment groups were randomly selected: a group receiving the belt only, a group receiving a 1 h training class only, a group receiving both a belt and a 1 h training class, and a control group receiving nothing. Two treatment groups were added which contained participants who discontinued use of the belt prior to the end of an 8-month study period. Results indicated that there were no significant differences for total lumbar injury incident rate, restricted workday case injury incident rate, lost workdays and restricted workdays rate, and worker's compensation rates. There was, however, a marginal significant difference for lost workday case injury incident rate. Groups with participants who wore the belt for a while then discontinued its use had a higher lost day case injury incident rate than did either the group receiving training only or the control group. Compliance was an overriding factor as the belt questionnaire response indicated that 58% of participants in the belt groups discontinued use of the belt before the end of 8 months. Comments made on the survey forms indicated that the belt was too hot. Similarly, comments suggested that the belt rubbed, pinched, and bruised ribs. Based on these results, the weightlifting belt used for this study cannot be recommended for use in aid of lifting during daily work activities of baggage handlers. Results indicate that use of the belts may, in fact, increase the risk of injury when not wearing a belt following a period of wearing a belt. As industries are experimenting with the use of belts, it is recommended that great care be taken in any further evaluation and close attention directed towards injuries which occur when not wearing the

Southwest Florida Shelf Ecosystems Analysis Study

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Southwest Florida Shelf Ecosystems Analysis Study produced grain size analyses in the historic 073 format for 299 sea floor samples collected from October 25,...

Timber resource statistics for southwest Washington.

Science.gov (United States)

Patricia M. Bassett; Daniel D. Oswald

1981-01-01

This report summarizes a 1978 timber-resource inventory of six counties in southwest Washington: Clark, Cowlitz, Lewis, Pacific, Skamania, and Wahkiakum. Detailed tables of forest area, timber volume, growth, mortality, and harvest are presented.

Belt of Yotvings. Radioecology

International Nuclear Information System (INIS)

Mazheika, J.; Petroshius, R.; Strzelecki, R.; Wolkovitcz, S.; Lewandowski, P.

1997-01-01

Full text: The map of gamma radiation dose of 'Belt of Yotvings' area displays the summarized gamma radiation coming from natural radionuclides of 238 U, 232 Th, 40 K and from cesium isotopes 137 Cs, 134 Cs, artificially supplied into the environment after the Chernobyl disaster. The average value of gamma radiation dose for 'Belt of Yotvings' area is 44.2 n Gy/h, with a distinct regional differentiation. The content of uranium varies from 0 to 4.5 g/t, with the average value of about 1.4 g/t. Thorium content varies from 0 to 10.3 g/t, with the average value of 4.3 g/t. Potassium content varies from 0.1 up to 2.5 %, with the average value of 1.2 %. The concentration of caesium radioisotopes reaches up to 11.6 kBq/m 2 , the average value being 3.8 kBq/m 2 . Radon concentration in soil air has been determined in 55 sites (83 analyses). Radon concentration has been noticed in volumes from trace amounts up to 55 kBq/m3.The radioecological mapping has documented that the highest concentrations of natural radioisotopes and, correspondingly, the highest total gamma radiation dose were observed in the northeastern part of the area studied, which is covered by clay-silty glaciolacustrine deposits. Slightly lower values are typical for the whole northwestern part of 'Belt of Yotvings'. Very low contents of radioactive elements and low total radiation doses are typical for eolian and sandur sands, occurring south-eastward from the line Augustow-Veisiejai. The Chernobyl NPP accident polluted the studied region with artificial cesium radioisotopes un significantly. The concentrations are low and they involve no radioecological hazard. The investigation of radon concentration in soil air have revealed several places affected by high radon emanation. These places should be studied in a more detailed way

Araguaia fold belt, new geochronological data

International Nuclear Information System (INIS)

Lafon, J.M.; Macambira, J.B.; Macambira, M.J.B.; Moura, C.A.V.; Souza, A.C.C.

1990-01-01

The northern part of the Araguaia Fold Belt (AFB) outcrops in a N-S direction for about 400 km in the state of Tocantins. Dome-like structures occur in this fold belt also in a N-S direction. Both deformation and metamorphism increase from the West to the East. The basement of the AFB consist of Colmeia complex and Cantao gneiss, which crop out mainly in the core of the dome-like structures. The supracrustals rocks of the fold belt belongs to the Baixo Araguaia supergroup which is divided into the lower Estrondo group and the upper Tocantins group. Preliminary Sm-Nd data from the Colmeia complex (Grota Rica dome) gave Archean model ages of 2.8 Ga (TNd sub(DM)) while Rb-Sr data in the same rocks give an age of 2530 ± 200 Ma. In the others dome-like structures, the Rb-Sr systematics gave ages for the Colmeia a complex of 2239 ± 47 Ma (Colmeia structure) and 1972 ± 46 Ma (Lontra structure). These younger ages are believed to represent partial to total isotopic resetting of the Rb-Sr system during the Transamazonian Event. The Rb-Sr studies of the Cantao gneiss gave an age of 1774 ± 31 Ma. (author)

40 CFR 81.97 - Southwest Florida Intrastate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Region. 81.97 Section 81.97 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.97 Southwest Florida Intrastate Air Quality Control Region. The Southwest Florida Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

40 CFR 81.118 - Southwest Missouri Intrastate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Region. 81.118 Section 81.118 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.118 Southwest Missouri Intrastate Air Quality Control Region. The Southwest Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

Materials of conference: Hydrogeological Problems of South-West Poland

International Nuclear Information System (INIS)

1996-01-01

Hydrogeological problems of South-west Poland is the collection of conference papers held in Szklarska Poreba on 20-22 June 1996. The materials have been gathered in three topical groups: water quality problems in hydrological cycle, regional hydrogeology of South-west Poland, theoretical problems and research methods in hydrogeology. More of performed articles have a interdisciplinary character taking into account the precipitation and surface water quality and their influence on ground water features

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives.

Science.gov (United States)

Chaitiemwong, N; Hazeleger, W C; Beumer, R R

2010-08-15

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives, in the absence or presence of food debris from meat, fish and vegetables and at temperatures of 10, 25 and 37 degrees C was investigated. The pathogen survived best at 10 degrees C, and better at 25 degrees C than at 37 degrees C on both conveyor belt materials. The reduction in the numbers of the pathogen on belt material with antimicrobial additives in the first 6h at 10 degrees C was 0.6 log unit, which was significantly higher (Padditives. Reductions were significantly less (Pfood residue. At 37 degrees C and 20% relative humidity, large decreases in the numbers of the pathogen on both conveyor belt materials during the first 6h were observed. Under these conditions, there was no obvious effect of the antimicrobial substances. However, at 25 degrees C and 10 degrees C and high humidity (60-75% rh), a rapid decrease in bacterial numbers on the belt material with antimicrobial substances was observed. Apparently the reduction in numbers of L. monocytogenes on belt material with antimicrobial additives was greater than on belt material without additives only when the surfaces were wet. Moreover, the presence of food debris neutralized the effect of the antimicrobials. The results suggest that the antimicrobial additives in conveyor belt material could help to reduce numbers of microorganisms on belts at low temperatures when food residues are absent and belts are not rapidly dried. Copyright 2010 Elsevier B.V. All rights reserved.

A Computerized Tomography Study of Vocal Tract Setting in Hyperfunctional Dysphonia and in Belting.

Science.gov (United States)

Saldias, Marcelo; Guzman, Marco; Miranda, Gonzalo; Laukkanen, Anne-Maria

2018-04-03

Vocal tract setting in hyperfunctional patients is characterized by a high larynx and narrowing of the epilaryngeal and pharyngeal region. Similar observations have been made for various singing styles, eg, belting. The voice quality in belting has been described to be loud, speech like, and high pitched. It is also often described as sounding "pressed" or "tense". The above mentioned has led to the hypothesis that belting may be strenuous to the vocal folds. However, singers and teachers of belting do not regard belting as particularly strenuous. This study investigates possible similarities and differences between hyperfunctional voice production and belting. This study concerns vocal tract setting. Four male patients with hyperfunctional dysphonia and one male contemporary commercial music singer were registered with computerized tomography while phonating on [a:] in their habitual speaking pitch. Additionally, the singer used the pitch G4 in belting. The scannings were studied in sagittal and transversal dimensions by measuring lengths, widths, and areas. Various similarities were found between belting and hyperfunction: high vertical larynx position, small hypopharyngeal width, and epilaryngeal outlet. On the other hand, belting differed from dysphonia (in addition to higher pitch) by a wider lip and jaw opening, and larger volumes of the oral cavity. Belting takes advantage of "megaphone shape" of the vocal tract. Future studies should focus on modeling and simulation to address sound energy transfer. Also, they should consider aerodynamic variables and vocal fold vibration to evaluate the "price of decibels" in these phonation types. Copyright © 2018. Published by Elsevier Inc.

Structural observations and U-Pb mineral ages from igneous rocks at the Archaean-Palaeoproterozoic boundary in the Salahmi Schist Belt, central Finland: constraints on tectonic evolution

Directory of Open Access Journals (Sweden)

Pietikäinen, K.

1999-06-01

Full Text Available The study area in Vieremä, central Finland, contains part of Archaean-Palaeoproterozoic boundary. In the east, the area comprises Archaean gneiss and the Salahmi Schist Belt. The rocks of the schist belt are turbiditic metagreywackes, with well-preserved depositional structures, occurring as Proterozoic wedge-shaped blocks, and staurolite schists, the latter representing higher-strained and metamorphosed equivalents of the metagreywackes. In the west of the area there is an Archaean gneiss block, containing strongly elongated structures, and deformed Svecofennian supracrustal rocks, which are cut by deformed granitoids. These are juxtaposed with the schist belt. The boundaries of these tectonometamorphic blocks are narrow, highly strained mylonites and thrust zones. The metamorphic grade of the supracrustal rocks increases from east to west, the increase being stepwise across the mylonitic block boundaries. The rocks are more deformed from east to west with younger structures overprinting. In the staurolite schists of the Salahmi Schist Belt, the most prominent structure is a lineation (L2 that overprints the bedding and axial plane foliation. In Sorronmäki quarry, at the western boundary of the schist belt, this Palaeoproterozoic lineation dominates all the structures in tonalite gneiss, which gives a U-Pb age of 2731±6 Ma. Southeast of the quarry, at the same boundary, the Salahmi schists have been overturned towards the northeast, suggesting that the Archaean gneiss at Sorronmäki has been thrust towards the northeast over these rocks. In the western part of the study area, the Leppikangas granodiorite that intrudes the Svecofennian supracrustal rocks gives a U-Pb age of 1891+6 Ma. In the granodiorite, a strong lineation formed by the intersection of two foliations, which maybe L2 is associated with thrusting towards the northeast. The monazite age of the Archaean Sorronmäki gneiss is 1817+3 Ma, and the titanite age of the Svecofennian

Using naturalistic driving data to identify variables associated with infrequent, occasional, and consistent seat belt use.

Science.gov (United States)

Reagan, Ian J; McClafferty, Julie A; Berlin, Sharon P; Hankey, Jonathan M

2013-01-01

Seat belt use is one of the most effective countermeasures to reduce traffic fatalities and injuries. The success of efforts to increase use is measured by road side observations and self-report questionnaires. These methods have shortcomings, with the former requiring a binary point estimate and the latter being subjective. The 100-car naturalistic driving study presented a unique opportunity to study seat belt use in that seat belt status was known for every trip each driver made during a 12-month period. Drivers were grouped into infrequent, occasional, or consistent seat belt users based on the frequency of belt use. Analyses were then completed to assess if these groups differed on several measures including personality, demographics, self-reported driving style variables as well as measures from the 100-car study instrumentation suite (average trip speed, trips per day). In addition, detailed analyses of the occasional belt user group were completed to identify factors that were predictive of occasional belt users wearing their belts. The analyses indicated that consistent seat belt users took fewer trips per day, and that increased average trip speed was associated with increased belt use among occasional belt users. The results of this project may help focus messaging efforts to convert occasional and inconsistent seat belt users to consistent users. Copyright © 2012 Elsevier Ltd. All rights reserved.

[Water and environment in the Southwest of Madagascar].

Science.gov (United States)

Razanamparany, L

1993-04-01

The dry and arid southwest region of Madagascar is not a desert but resembles the Sahel region of West Africa. The chronic water deficit is aggravated by the heat and constant winds that accelerate evapotranspiration on the permeable soils. The dryness occurs because the southwest region lies outside the main pluviogenic systems. Erosion occurs at all seasons. In the winter the sun and winds are the main causes, while the rare storms are more conducive to run-off and to erosion than to absorption. The acute water shortage in the southwest has prompted hydrogeologic research and well-drilling, but the high salt content of the water and other impurities will be a limiting factor for development of the area. The population of the southwest is extremely mobile. Human settlements are concentrated in the valleys and depressions and along major roads. Customary rights to land under the control of the traditional chiefs regulate tenure in most areas. But especially in the river bottoms, the coming of cash crops cultivated with modern equipment has resulted in significant erosion which has aggravated ecological problems. Accelerating soil degradation has led peasants to extend their lands under cultivation to the detriment of forest cover. Cattle herding remains the principal economic activity in the southwest. Herding has progressed from nomadism to pastoralism, but it remains a sign of power and wealth. Transhumance is the strategy of herders faced with shortages of water and pasturage, demographic pressure, and environmental degradation. Raising of sheep and goats constitutes a supplemental food source, medium of exchange, and form of savings. But angora goats graze on everything in their path, devastating their surrounds. Fear of cattle thefts militates against efforts to improve the quality of the stock. The various problems together have prompted a wasteful exploitation of the forest resources. Development strategies for the area explored by the government have all

Pilot-scale continuous ultrasonic cleaning equipment reduces Listeria monocytogenes levels on conveyor belts.

Science.gov (United States)

Tolvanen, Riina; Lundén, Janne; Hörman, Ari; Korkeala, Hannu

2009-02-01

Ultrasonic cleaning of a conveyor belt was studied by building a pilot-scale conveyor with an ultrasonic cleaning bath. A piece of the stainless steel conveyor belt was contaminated with meat-based soil and Listeria monocytogenes strains (V1, V3, and B9) and incubated for 72 h to allow bacteria to attach to the conveyor belt surfaces. The effect of ultrasound with a potassium hydroxide-based cleaning detergent was determined by using the cleaning bath at 45 and 50 degrees C for 30 s with and without ultrasound. The detachment of L. monocytogenes from the conveyor belt caused by the ultrasonic treatment was significantly greater at 45 degrees C (independent samples t test, P conveyor belt is effective even with short treatment times.

Motivating signage prompts safety belt use among drivers exiting senior communities.

Science.gov (United States)

Cox, B S; Cox, A B; Cox, D J

2000-01-01

Senior drivers are vulnerable to automobile crashes and subsequent injury and death. Safety belts reduce health risks associated with auto crashes. Therefore, it is important to encourage senior drivers to wear safety belts while driving. Using an AB design, replicated five times, we evaluated the short- and long-term effects of a sign with the message "BUCKLE UP, STAY SAFE" attached to a stop sign at the exits of five different senior communities. Safety belt use was stable during two pretreatment assessments averaged across the five sites and 250 drivers (72% and 68% usage), but significantly increased following installation of these signs (94% usage). Six months after installation of the signs, the effect persisted (88% usage). Use of such signs may be a cost-effective way of promoting safety belt use.

Synthetic approaches to aromatic belts: building up strain in macrocyclic polyarenes.

Science.gov (United States)

Eisenberg, David; Shenhar, Roy; Rabinovitz, Mordecai

2010-08-01

This tutorial review discusses synthetic strategies towards aromatic belts, defined here as double-stranded conjugated macrocycles, such as [n]cyclacenes, [n]cyclophenacenes, Schlüter belt, and Vögtle belt. Their appeal stems, firstly, from the unique nature of their conjugation, having p orbitals oriented radially rather than perpendicular to the plane of the macrocycle. Secondly, as aromatic belts are model compounds of carbon nanotubes of different chiralities, a synthetic strategy towards the buildup of structural strain in these compounds could finally open a route towards rational chemical synthesis of carbon nanotubes. The elusiveness of these compounds has stimulated fascinating and ingenious synthetic strategies over the last decades. The various strategies are classified here by their approach to the buildup of structural strain, which is the main obstacle in the preparation of these curved polyarenes.

Resolving the planetesimal belt of HR 8799 with ALMA

Science.gov (United States)

Booth, Mark; Jordán, Andrés; Casassus, Simon; Hales, Antonio S.; Dent, William R. F.; Faramaz, Virginie; Matrà, Luca; Barkats, Denis; Brahm, Rafael; Cuadra, Jorge

2016-07-01

The star HR 8799 hosts one of the largest known debris discs and at least four giant planets. Previous observations have found evidence for a warm belt within the orbits of the planets, a cold planetesimal belt beyond their orbits and a halo of small grains. With the infrared data, it is hard to distinguish the planetesimal belt emission from that of the grains in the halo. With this in mind, the system has been observed with ALMA in band 6 (1.34 mm) using a compact array format. These observations allow the inner edge of the planetesimal belt to be resolved for the first time. A radial distribution of dust grains is fitted to the data using an MCMC method. The disc is best fitted by a broad ring between 145^{+12}_{-12} au and 429^{+37}_{-32} au at an inclination of 40^{+5}_{-6}° and a position angle of 51^{+8}_{-8}°. A disc edge at ˜145 au is too far out to be explained simply by interactions with planet b, requiring either a more complicated dynamical history or an extra planet beyond the orbit of planet b.

Design of dual energy x-ray detector for conveyor belt with steel wire ropes

Science.gov (United States)

Dai, Yue; Miao, Changyun; Rong, Feng

2009-07-01

A dual energy X-ray detector for conveyor belt with steel wire ropes is researched in the paper. Conveyor belt with steel wire ropes is one of primary transfer equipments in modern production. The traditional test methods like electromagnetic induction principle could not display inner image of steel wire ropes directly. So X-ray detection technology has used to detect the conveyor belt. However the image was not so clear by the interference of the rubber belt. Therefore, the dualenergy X-ray detection technology with subtraction method is developed to numerically remove the rubber belt from radiograph, thus improving the definition of the ropes image. The purpose of this research is to design a dual energy Xray detector that could make the operator easier to found the faulty of the belt. This detection system is composed of Xray source, detector controlled by FPGA chip, PC for running image processing system and so on. With the result of the simulating, this design really improved the capability of the staff to test the conveyor belt.

Seat-belt use still low in Kuwait: self-reported driving behaviours among adult drivers.

Science.gov (United States)

Raman, Sudha R; Ottensmeyer, C Andrea; Landry, Michel D; Alfadhli, Jarrah; Procter, Steven; Jacob, Susan; Hamdan, Elham; Bouhaimed, Manal

2014-01-01

Kuwait mandated seat-belt use by drivers in 1976 and by front seat passengers in 1994. The study objectives were to identify and estimate current factors associated with seat-belt use and levels of potentially unsafe driving behaviours in Kuwait. In 2010, 741 adults were surveyed regarding driving habits and history. Only 41.6% of drivers reported always using a seat belt. Front seat passenger belt use was more common (30.5%) than rear seat belt use (6.5%). Distracted driving behaviours were common, including mobile phone use ('always' or 'almost always': 51.1%) and texting/SMS (32.4%). Logistic regression indicated that drivers who were young (18-19 years), male, Kuwaiti nationals or non-Kuwaiti Arabs, drove over the speed limit, had traffic violation tickets or >1 car crashes in the last year, were less likely to use seat belts. Targeted initiatives to increase public awareness and to enforce car-safety legislation, including use of seat belts, are necessary to decrease the health burden of car crashes in Kuwait.

Nontuberculous mycobacteria: incidence in Southwest Ireland from 1987 to 2000.

LENUS (Irish Health Repository)

Kennedy, M P

2012-02-03

SETTING: The Southwest of Ireland (Counties Cork and Kerry) 1987-2000, average population 549,500. OBJECTIVE: Nontuberculous mycobacteria (NTM) cause significant morbidity worldwide and the study of epidemiology and characteristics helps in their prevention and treatment. This study was performed to determine the incidence of NTM disease in comparison to Mycobacterium tuberculosis (M. tuberculosis) and Mycobacterium bovis (M. bovis) in Southwest Ireland, over the above time period. DESIGN: A retrospective study was carried out in all human isolates of NTM, M. tuberculosis and M. bovis between 1987 and 2000, in the Southwest Region of Ireland. RESULTS: The mean incidence of NTM (0.4\\/100,000 population) has risen since 1995, principally of pulmonary Mycobacterium avium intracellulare complex (MAC). The annual incidence of M. tuberculosis in humans over 14 years in the same region was 971\\/100,000 population with a significant reduction since 1994 and M. bovis remained constant at 0.5\\/100,000 population. CONCLUSION: The increasing incidence of disease causing NTM noted in Southwest Ireland reflects global data and is surmised to be due to an ageing population, increased incidence related to chronic fibrotic lung disease, and environmental mycobacterial factors.

A belt charging system for the Vivitron - design, early results

International Nuclear Information System (INIS)

Helleboid, J.M.; Gaudiot, G.

1990-10-01

A specific belt charging system has been designed, built and assembled for the 35 MV Vivitron. 100 m long belt is used. Together with main features of the design, experimental studies, tests in a pilot machine and the results of the very early tests of the real system are reviewed

Respiratory Belt Transducer Constructed Using a Singing Greeting Card Beeper

Science.gov (United States)

Bhaskar, Anand; Subramani, Selvam; Ojha, Rajdeep

2013-01-01

An article by Belusic and Zupancic described the construction of a finger pulse sensor using a singing greeting card beeper. These authors felt that this beeper made of piezoelectric material could be easily modified to function as a respiratory belt transducer to monitor respiratory movements. Commercially available respiratory belt transducers,…

Cultural Arts in the Southwest.

Science.gov (United States)

Cross, Kate

1998-01-01

Presents a pottery project for eighth-grade students based on a study of ancient and modern forms of Pueblo Indian pottery of the Southwest United States. Details the process for creating either carved, red clay, or painted white clay pottery typical of these cultural groups. Relates student reactions to the project. (DSK)

The Navy’s Environmental Program and Opportunities in the Southwest

Science.gov (United States)

2013-08-27

Achieve RIP for all High Priority IRP Sites FY14 •Achieve RC for 90% of IRP + MRP Sites FY18 •Achieve RC for 95% of IRP + MRP Sites FY21 9 NAVFAC Southwest...8/21/2013 ER,N IRP vs. MRP ($M) NAVFAC SW 0 10 20 30 40 50 60 70 FY 13 FY 14 FY 15 FY 16 FY 17 FY 18 FY 19 FY 20 FY 21 4 4 7 7 7 43 54 42 51...50 57 58 58 51 18 15 11 9 MRP IRP 10 NAVFAC Southwest Southwest ER,N Requirements Overall CTC: $766M ~54% IRP; ~46% MRP IRP , $411 MRP

Upper limit on the inner radiation belt MeV electron intensity

Science.gov (United States)

Li, X; Selesnick, RS; Baker, DN; Jaynes, AN; Kanekal, SG; Schiller, Q; Blum, L; Fennell, J; Blake, JB

2015-01-01

No instruments in the inner radiation belt are immune from the unforgiving penetration of the highly energetic protons (tens of MeV to GeV). The inner belt proton flux level, however, is relatively stable; thus, for any given instrument, the proton contamination often leads to a certain background noise. Measurements from the Relativistic Electron and Proton Telescope integrated little experiment on board Colorado Student Space Weather Experiment CubeSat, in a low Earth orbit, clearly demonstrate that there exist sub-MeV electrons in the inner belt because their flux level is orders of magnitude higher than the background, while higher-energy electron (>1.6 MeV) measurements cannot be distinguished from the background. Detailed analysis of high-quality measurements from the Relativistic Electron and Proton Telescope on board Van Allen Probes, in a geo-transfer-like orbit, provides, for the first time, quantified upper limits on MeV electron fluxes in various energy ranges in the inner belt. These upper limits are rather different from flux levels in the AE8 and AE9 models, which were developed based on older data sources. For 1.7, 2.5, and 3.3 MeV electrons, the upper limits are about 1 order of magnitude lower than predicted model fluxes. The implication of this difference is profound in that unless there are extreme solar wind conditions, which have not happened yet since the launch of Van Allen Probes, significant enhancements of MeV electrons do not occur in the inner belt even though such enhancements are commonly seen in the outer belt. Key Points Quantified upper limit of MeV electrons in the inner belt Actual MeV electron intensity likely much lower than the upper limit More detailed understanding of relativistic electrons in the magnetosphere PMID:26167446

The effectiveness of automatic belts in reducing fatality rates in Toyota Cressidas.

Science.gov (United States)

Nash, C E

1989-12-01

Toyota Cressidas have had motor driven automatic belts since 1981. Their observed use rates have been consistently close to 100%. This paper compares fatality rates in Toyota Cressidas with those in the similar Nissan Maximas (which are equipped with three-point manual belts) using the latest data from the Fatal Accident Reporting System. After making adjustments for differences in the average ages of front seat occupants of the two fleets, the Toyotas have a fatality rate that is about three-quarters that of the Nissans. From this, the fatality-reducing effectiveness for the Toyota automatic belts is estimated to be 40% with an uncertainty of +/- 8%. This effectiveness estimate is consistent with earlier estimates of automatic belt effectiveness.

Fall Protection Characteristics of Safety Belts and Human Impact Tolerance.

Science.gov (United States)

Hino, Yasumichi; Ohdo, Katsutoshi; Takahashi, Hiroki

2014-08-23

Many fatal accidents due to falls from heights have occurred at construction sites not only in Japan but also in other countries. This study aims to determine the fall prevention performance of two types of safety belts: a body belt 1) , which has been used for more than 40 yr in the Japanese construction industry as a general type of safety equipment for fall accident prevention, and a full harness 2, 3) , which has been used in many other countries. To determine human tolerance for impact trauma, this study discusses features of safety belts with reference 4-9) to relevant studies in the medical science, automobile crash safety, and aircrew safety. For this purpose, simple drop tests were carried out in a virtual workplace to measure impact load, head acceleration, and posture in the experiments, the Hybrid-III pedestrian model 10) was used as a human dummy. Hybrid-III is typically employed in official automobile crash tests (New Car Assessment Program: NCAP) and is currently recognized as a model that faithfully reproduces dynamic responses. Experimental results shows that safety performance strongly depends on both the variety of safety belts used and the shock absorbers attached onto lanyards. These findings indicate that fall prevention equipment, such as safety belts, lanyards, and shock absorbers, must be improved to reduce impact injuries to the human head and body during falls.

THE SURFACE COMPOSITION OF LARGE KUIPER BELT OBJECT 2007 OR10

International Nuclear Information System (INIS)

Brown, M. E.; Fraser, W. C.; Burgasser, A. J.

2011-01-01

We present photometry and spectra of the large Kuiper belt object 2007 OR10. The data show significant near-infrared absorption features due to water ice. While most objects in the Kuiper belt with water ice absorption this prominent have the optically neutral colors of water ice, 2007 OR10 is among the reddest Kuiper belt objects known. One other large Kuiper belt object-Quaoar-has similar red coloring and water ice absorption, and it is hypothesized that the red coloration of this object is due to irradiation of the small amounts of methane able to be retained on Quaoar. 2007 OR10, though warmer than Quaoar, is in a similar volatile retention regime because it is sufficiently larger that its stronger gravity can still retain methane. We propose, therefore, that the red coloration on 2007 OR10 is also caused by the retention of small amounts of methane. Positive detection of methane on 2007 OR10 will require spectra with higher signal to noise. Models for volatile retention on Kuiper belt objects appear to continue to do an excellent job reproducing all of the available observations.

A physical model for extreme drought over southwest Asia: Chapter 17

Science.gov (United States)

Hoell, Andrew; Funk, Chris; Barlow, Mathew; Cannon, Forrest

2017-01-01

The socioeconomic difficulties of southwest Asia, defined as the area bound by the domain 25°N–40°N and 40°E–70°E, are exacerbated by extreme precipitation deficits during the November–April rainy season. The precipitation deficits during many southwest Asia droughts have been examined in terms of the forcing by climate variability originating over the Pacific Ocean as a result of the El Niño–Southern Oscillation (ENSO), Pacific decadal variability (PDV), and the long-term warming of Pacific (LT) sea surface temperatures (SST). Here we examine how the most extreme November–April southwest Asia droughts relate to global SSTs and the associated large-scale atmospheric circulation anomalies and analyze the specific atmospheric forcing mechanisms responsible for changes in regional southwest Asian precipitation. The driest November–April seasons during 1948–2012 over southwest Asia are forced by subsidence and reductions of moisture fluxes as a result of the interaction of the mean flow with anomalous zonally symmetric high pressure throughout the Northern Hemisphere. The anomalous zonally symmetric high pressure throughout the Northern Hemisphere occurs simultaneously with cool central and eastern Pacific SST anomalies associated with La Niña and the negative phase of PDV and a warm west Pacific Ocean caused in part by the long-term warming of the west Pacific Ocean.

Radiation Belts of Antiparticles in Planetary Magnetospheres

Science.gov (United States)

Pugacheva, G. I.; Gusev, A. A.; Jayanthi, U. B.; Martin, I. M.; Spjeldvik, W. N.

2007-05-01

The Earth's radiation belts could be populated, besides with electrons and protons, also by antiparticles, such as positrons (Basilova et al., 1982) and antiprotons (pbar). Positrons are born in the decay of pions that are directly produced in nuclear reactions of trapped relativistic inner zone protons with the residual atmosphere at altitudes in the range of about 500 to 3000 km over the Earth's surface. Antiprotons are born by high energy (E > 6 GeV) cosmic rays in p+p - p+p+p+ pbar and in p+p - p+p+n+nbar reactions. The trapping and storage of these charged anti-particles in the magnetosphere result in radiation belts similar to the classical Van Allen belts of protons and electrons. We describe the mathematical techniques used for numerical simulation of the trapped positron and antiproton belt fluxes. The pion and antiproton yields were simulated on the basis of the Russian nuclear reaction computer code MSDM, a Multy Stage Dynamical Model, Monte Carlo code, (i.e., Dementyev and Sobolevsky, 1999). For estimates of positron flux there we have accounted for ionisation, bremsstrahlung, and synchrotron energy losses. The resulting numerical estimates show that the positron flux with energy >100 MeV trapped into the radiation belt at L=1.2 is of the order ~1000 m-2 s-1 sr-1, and that it is very sensitive to the shape of the trapped proton spectrum. This confined positron flux is found to be greater than that albedo, not trapped, mixed electron/positron flux of about 50 m-2 s-1 sr-1 produced by CR in the same region at the top of the geomagnetic field line at L=1.2. As we show in report, this albedo flux also consists mostly of positrons. The trapped antiproton fluxes produced by CR in the Earth's upper rarified atmosphere were calculated in the energy range from 10 MeV to several GeV. In the simulations we included a mathematic consideration of the radial diffusion process, both an inner and an outer antiproton source, losses of particles due to ionization process

49 CFR 571.209 - Standard No. 209; Seat belt assemblies.

Science.gov (United States)

2010-10-01

... seat belt assembly to fit the user, including such hardware that may be integral with a buckle... the proper use of the assembly, stressing particularly the importance of wearing the assembly snugly... of Standard No. 208. (a)(1) A manual seat belt assembly, which is subject to the requirements of S5.1...

Alien Asteroid Belt Compared to our Own

Science.gov (United States)

2005-01-01

[figure removed for brevity, see original site] Figure 1: Band of Light Comparison This artist's concept illustrates what the night sky might look like from a hypothetical alien planet in a star system with an asteroid belt 25 times as massive as the one in our own solar system (alien system above, ours below; see Figure 1). NASA's Spitzer Space Telescope found evidence for such a belt around the nearby star called HD 69830, when its infrared eyes spotted dust, presumably from asteroids banging together. The telescope did not find any evidence for a planet in the system, but astronomers speculate one or more may be present. The movie begins at dusk on the imaginary world, when HD 69830, like our Sun, has begun to set over the horizon. Time is sped up to show the onset of night and the appearance of a brilliant band of light. This light comes from dust in a massive asteroid belt, which scatters sunlight. In our solar system, anybody observing the skies on a moonless night far from city lights can see the sunlight that is scattered by dust in our asteroid belt. Called zodiacal light and sometimes the 'false dawn,' this light appears as a dim band stretching up from the horizon when the Sun is about to rise or set. The light is faint enough that the disk of our Milky Way galaxy remains the most prominent feature in the sky. (The Milky Way disk is shown perpendicular to the zodiacal light in both pictures.) In contrast, the zodiacal light in the HD 69830 system would be 1,000 times brighter than our own, outshining even the Milky Way.

Desert basins of the Southwest

Science.gov (United States)

Leake, Stanley A.; Konieczki, Alice D.; Rees, Julie A.H.

2000-01-01

Ground water is among the Nation’s most important natural resources. It provides drinking water to urban and rural communities, supports irrigation and industry, sustains the flow of streams and rivers, and maintains riparian and wetland ecosystems. In many areas of the Nation, the future sustainability of ground-water resources is at risk from overuse and contamination. Because ground-water systems typically respond slowly to human actions, a long-term perspective is needed to manage this valuable resource. This publication is one in a series of fact sheets that describe ground-water-resource issues across the United States, as well as some of the activities of the U.S. Geological Survey that provide information to help others develop, manage, and protect ground-water resources in a sustainable manner. Ground-water resources in the Southwest are among the most overused in the United States. Natural recharge to aquifers is low and pumping in many areas has resulted in lowering of water tables. The consequences of large-scale removal of water from storage are becoming increasingly evident. These consequences include land subsidence; loss of springs, streams, wetlands and associated habitat; and degradation of water quality. Water managers are now seeking better ways of managing ground-water resources while looking for supplemental sources of water. This fact sheet reviews basic information on ground water in the desert basins of the Southwest. Also described are some activities of the U.S. Geological Survey (USGS) that are providing scientific information for sustainable management of ground-water resources in the Southwest. Ground-water sustainability is defined as developing and using ground water in a way that can be maintained for an indefinite time without causing unacceptable environmental, economic, or social consequences.

Does subterranean flow initiate mud banks off the southwest coast of India?

Digital Repository Service at National Institute of Oceanography (India)

Balachandran, K.K.

Coastal waters off the southwest coast of India draw special attention because of the occurrence of mud banks at certain locations during southwest monsoon period. The present study puts forward a hypothesis of a subterranean flow, which could be a...

Mexican-Americans in the Southwest.

Science.gov (United States)

Galarza, Ernesto; And Others

With findings as presented in this 1969 book, a 2-year field study conducted by a 3-member team analyzed the economic, cultural, political, and educational conditions of Mexican Americans in the Southwest (California, Arizona, New Mexico, Colorado, and Texas) with some reference to braceros and the situation in Mexico. An overview of 8 geographic…

Alkaline intrusion in a granulite ensemble in the Eastern Ghats belt

Indian Academy of Sciences (India)

Alkaline magmatism; Eastern Ghats belt; pull-apart structure; plume tectonics. ... is one of several bodies in the high-grade Eastern Ghats belt, but this one is an ... Geological Studies Unit, Indian Statistical Institute, 203 B. T. Road, Kolkata 700 ...

The atmospheric implications of radiation belt remediation

Directory of Open Access Journals (Sweden)

C. J. Rodger

2006-08-01

Full Text Available High altitude nuclear explosions (HANEs and geomagnetic storms can produce large scale injections of relativistic particles into the inner radiation belts. It is recognised that these large increases in >1 MeV trapped electron fluxes can shorten the operational lifetime of low Earth orbiting satellites, threatening a large, valuable population. Therefore, studies are being undertaken to bring about practical human control of the radiation belts, termed "Radiation Belt Remediation" (RBR. Here we consider the upper atmospheric consequences of an RBR system operating over either 1 or 10 days. The RBR-forced neutral chemistry changes, leading to NOx enhancements and Ox depletions, are significant during the timescale of the precipitation but are generally not long-lasting. The magnitudes, time-scales, and altitudes of these changes are no more significant than those observed during large solar proton events. In contrast, RBR-operation will lead to unusually intense HF blackouts for about the first half of the operation time, producing large scale disruptions to radio communication and navigation systems. While the neutral atmosphere changes are not particularly important, HF disruptions could be an important area for policy makers to consider, particularly for the remediation of natural injections.

Formation and Decay of the Inner Electron Radiation Belt

Science.gov (United States)

2017-01-09

a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 09-01-2017 2. REPORT TYPE...radiation belt: CRAND and trapped solar protons......17 APPENDIX C - Inward diffusion and loss of radiation belt protons...transfer orbit that can be damaged by the intense charged -particle environment. Protons are the prominent hazard, often causing single event upsets in

E3 Success Story - E3 Southwest Virginia: Economy, Energy and the Environment

Science.gov (United States)

E3 Southwest Virginia supports sustainable manufacturing in 17 counties in southwest Virginia. The MTC provides manufacturers with assessments of production processes to reduce their energy consumption and drive innovation.

An Experimental Concept for Probing Nonlinear Physics in Radiation Belts

Science.gov (United States)

Crabtree, C. E.; Ganguli, G.; Tejero, E. M.; Amatucci, B.; Siefring, C. L.

2017-12-01

A sounding rocket experiment, Space Measurement of Rocket-Released Turbulence (SMART), can be used to probe the nonlinear response to a known stimulus injected into the radiation belt. Release of high-speed neutral barium atoms (8- 10 km/s) generated by a shaped charge explosion in the ionosphere can be used as the source of free energy to seed weak turbulence in the ionosphere. The Ba atoms are photo-ionized forming a ring velocity distribution of heavy Ba+ that is known to generate lower hybrid waves. Induced nonlinear scattering will convert the lower hybrid waves into EM whistler/magnetosonic waves. The escape of the whistlers from the ionospheric region into the radiation belts has been studied and their observable signatures quantified. The novelty of the SMART experiment is to make coordinated measurement of the cause and effect of the turbulence in space plasmas and from that to deduce the role of nonlinear scattering in the radiation belts. Sounding rocket will carry a Ba release module and an instrumented daughter section that includes vector wave magnetic and electric field sensors, Langmuir probes and energetic particle detectors. The goal of these measurements is to determine the whistler and lower hybrid wave amplitudes and spectrum in the ionospheric source region and look for precipitated particles. The Ba release may occur at 600-700 km near apogee. Ground based cameras and radio diagnostics can be used to characterize the Ba and Ba+ release. The Van Allen Probes can be used to detect the propagation of the scattering-generated whistler waves and their effects in the radiation belts. By detecting whistlers and measuring their energy density in the radiation belts the SMART mission will confirm the nonlinear generation of whistlers through scattering of lower hybrid along with other nonlinear responses of the radiation belts and their connection to weak turbulence.

Numerical modeling of water spray suppression of conveyor belt fires in a large-scale tunnel.

Science.gov (United States)

Yuan, Liming; Smith, Alex C

2015-05-01

Conveyor belt fires in an underground mine pose a serious life threat to miners. Water sprinkler systems are usually used to extinguish underground conveyor belt fires, but because of the complex interaction between conveyor belt fires and mine ventilation airflow, more effective engineering designs are needed for the installation of water sprinkler systems. A computational fluid dynamics (CFD) model was developed to simulate the interaction between the ventilation airflow, the belt flame spread, and the water spray system in a mine entry. The CFD model was calibrated using test results from a large-scale conveyor belt fire suppression experiment. Simulations were conducted using the calibrated CFD model to investigate the effects of sprinkler location, water flow rate, and sprinkler activation temperature on the suppression of conveyor belt fires. The sprinkler location and the activation temperature were found to have a major effect on the suppression of the belt fire, while the water flow rate had a minor effect.

Numerical modeling of water spray suppression of conveyor belt fires in a large-scale tunnel

Science.gov (United States)

Yuan, Liming; Smith, Alex C.

2015-01-01

Conveyor belt fires in an underground mine pose a serious life threat to miners. Water sprinkler systems are usually used to extinguish underground conveyor belt fires, but because of the complex interaction between conveyor belt fires and mine ventilation airflow, more effective engineering designs are needed for the installation of water sprinkler systems. A computational fluid dynamics (CFD) model was developed to simulate the interaction between the ventilation airflow, the belt flame spread, and the water spray system in a mine entry. The CFD model was calibrated using test results from a large-scale conveyor belt fire suppression experiment. Simulations were conducted using the calibrated CFD model to investigate the effects of sprinkler location, water flow rate, and sprinkler activation temperature on the suppression of conveyor belt fires. The sprinkler location and the activation temperature were found to have a major effect on the suppression of the belt fire, while the water flow rate had a minor effect. PMID:26190905

Radiation Belt Test Model

Science.gov (United States)

Freeman, John W.

2000-10-01

Rice University has developed a dynamic model of the Earth's radiation belts based on real-time data driven boundary conditions and full adiabaticity. The Radiation Belt Test Model (RBTM) successfully replicates the major features of storm-time behavior of energetic electrons: sudden commencement induced main phase dropout and recovery phase enhancement. It is the only known model to accomplish the latter. The RBTM shows the extent to which new energetic electrons introduced to the magnetosphere near the geostationary orbit drift inward due to relaxation of the magnetic field. It also shows the effects of substorm related rapid motion of magnetotail field lines for which the 3rd adiabatic invariant is violated. The radial extent of this violation is seen to be sharply delineated to a region outside of 5Re, although this distance is determined by the Hilmer-Voigt magnetic field model used by the RBTM. The RBTM appears to provide an excellent platform on which to build parameterized refinements to compensate for unknown acceleration processes inside 5Re where adiabaticity is seen to hold. Moreover, built within the framework of the MSFM, it offers the prospect of an operational forecast model for MeV electrons.

Determining the Relationship of Primary Seat Belt Laws to Minority Ticketing

Science.gov (United States)

2011-09-01

Racial profiling is often raised as an issue when States change their seat belt law from secondary enforcement (i.e., stop only for some other violation) to primary enforcement (i.e., stop for an observed belt law violation alone). Thirteen States ma...

Idealized debris flow in flume with bed driven by a conveyor belt

Science.gov (United States)

Ling, Chi-Hai; Chen, Cheng-lung

1989-01-01

The generalized viscoplastic fluid (GVF) model is used to derive the theoretical expressions of two-dimensional velocities and surface profile for debris flow established in a flume with bed driven by a conveyor belt. The rheological parameters of the GVF model are evaluated through the comparison of theoretical results with measured data. A slip velocity of the established (steady) nonuniform flow on the moving bed (i.e., the conveyor belt) is observed, and a relation between the slip velocity and the velocity gradient at the bed is derived. Two belts, one rough and the other smooth, were tested. The flow profile in the flume is found to be linear and dependent on the roughness of the belt, but not much on its speed.

Assessing child belt fit, volume II : effect of restraint configuration, booster seat designs, seating procedure, and belt fit on the dynamic response of the hybrid III 10-year-old ATD in sled tests.

Science.gov (United States)

2008-09-01

A total of 49 dynamic sled tests were performed with the Hybrid III 10YO to examine issues relating to child belt fit. The goals of these tests were to evaluate ATD response to realistic belt geometries and belt fit, develop methods for accurate, rep...

Identification of thermotectonics events by 40Ar/39Ar methodology, in Jauru, Pontes e Lacerda and Rio Alegre Terrane - southwest portion of Amazon Craton

International Nuclear Information System (INIS)

Paulo, Valeria Guimaraes de

2005-01-01

The southwest portion of Amazon Craton, subject of these work, correspond to the southwest region of Mato Grosso State and is inserted on Rio Negro-Juruena, Rondoniana-San Ignacio and Sunsas-Aguapei geochronologic Provinces. This region is surrounded by three big terranes: Jauru, Pontes e Lacerda and Rio Alegre. The main aim of this study is to use the ages of termochronologic events obtained by 40 Ar/ 39 Ar methodology, including data of literature, to contribute with the study of the geotectonic evolution on this region. Twenty samples were analyzed and 40 Ar/ 39 Ar ages found for the Jauru Terrane vary of 1539 ± 3 Ma to 1338 ± 3 Ma, for the Pontes e Lacerda Terrane the interval obtained was of 946,1 ± 0,8 Ma to 890 ± 2 Ma and for Rio Alegre Terrane the ages are between 1407 ± 3 Ma to 1321 ± 2 Ma. U/Pb, Rb/Sr and Sm/Nd data from previous works, together with 40 Ar/ 39 Ar results allowed to obtain cooling average rates to each terrane. The Jauru Terrane units cooling age is equivalent to 1,52 Ga. The cooling average rates found to Alto Jauru Greenstone belt rocks is 2,4 deg C - 1,0 Ma and to Magmatic Arc Cachoeirinha is 10,8 deg C - 1,0 Ma. Stabilization age obtained for Pontes and Lacerda Terrane is about 900 Ma coherent with the cooling age of the Sunsas Aguapei Event (1,0 - 0,9 Ga) and cooling average rates calculate were the lower, equivalent to 1,0 deg C - 1,0 Ma. Cooling age found in Rio Alegre Terrane was 1,35 Ga, possibility correspond to collision age these terrane with Amazonian protoCraton and cooling average rates of 5,0 deg C - 1,0 Ma. Finally, younger age found of 900 Ma, coherent to the Sunsas - Aguapei Event, probably represent the last regional event that affected these rocks, characterizing the stabilization period of the southwest portion of Amazon Craton. (author)

Attachment of Salmonella serovars and Listeria monocytogenes to stainless steel and plastic conveyor belts.

Science.gov (United States)

Veluz, G A; Pitchiah, S; Alvarado, C Z

2012-08-01

In poultry industry, cross-contamination due to processing equipment and contact surfaces is very common. This study examined the extent of bacterial attachment to 6 different types and design of conveyor belts: stainless steel-single loop, stainless steel-balance weave, polyurethane with mono-polyester fabric, acetal, polypropylene mesh top, and polypropylene. Clean conveyor belts were immersed separately in either a cocktail of Salmonella serovars (Salmonella Typhimurium and Salmonella Enteritidis) or Listeria monocytogenes strains (Scott A, Brie 1, ATCC 6744) for 1 h at room temperature. Soiled conveyor chips were dipped in poultry rinses contaminated with Salmonella or Listeria cocktail and incubated at 10°C for 48 h. The polyurethane with mono-polyester fabric conveyor belt and chip exhibited a higher (Pconveyor belt attached a lower (Pconveyor belts exhibited stronger bacterial adhesion compared with stainless steel. The result suggests the importance of selecting the design and finishes of conveyor belt materials that are most resistant to bacterial attachment.

An experimental investigation of microalgal dewatering efficiency of belt filter system

Directory of Open Access Journals (Sweden)

Anjali Sandip

2015-11-01

Full Text Available The objective of this study was to investigate the microalgal dewatering efficiency of a belt filter system for feed concentrations below 10 g dry wt./L. A prototype belt filtration system designed for 50 g dry wt./L microalgal feed concentration was used for this investigation. The highest concentration of microalgal suspension available for testing on the prototype belt filtration system was 6 g dry wt./L obtained from biomass settling tanks at the Lawrence, Kansas domestic wastewater treatment plant. For preparation of feed suspension with concentrations below 10 g dry wt./L, microalgal cultivation was followed by flocculation. A mixed laboratory culture of freshwater species dominated by three eukaryotic green microalgae (Chlorella vulgaris, Scenedesmus sp., and Kirchneriella sp. was cultivated in wastewater effluent. This was followed by flocculation which resulted in a microalgal feed suspension concentration of 4 g dry wt./L. Belt dewatering tests were conducted on microalgal suspensions with feed concentrations of 4 g dry wt./L and 6 g dry wt./L. The maximum microalgal recovery with the belt dewatering system was 46% from the 4 g dry wt./L, and 84% from the 6 g dry wt./L suspensions respectively. The results of this study indicate that microalgal suspension concentrations as low as 6 g dry wt./L can be recovered with a belt filter system improving the overall dewatering efficiency of the system.

Number of conveyor belts optimization regarding to its type and logistical parameters in mining industry

Directory of Open Access Journals (Sweden)

Dušan Malindžák

2008-12-01

Full Text Available Material transportation by belt conveyers is widely used in many industrial branches including mining plants. Belt conveyingdevelopment during the last year was oriented mainly on construction of belts. The consequence of this is the improvement of itsmanufacture qualities bringing down the costs for their exchange and maintenance.Despite the fact that there are some theoreticalcalculations based on a standards it is common in the industry that the belt is not properly selected or it is overdesigned or number of itstypes is too large what can lead to increased costs for its storage. The paper describes the optimization of number of belt types in miningcompany SIDERIT, s. r. o. Nižná Slaná by the method of modernization and unification of belts under practical skills and projectingbased on theoretical calculations.

The sedimentary dynamics in natural and human-influenced delta channel belts

NARCIS (Netherlands)

Hobo, N.

2015-01-01

This study investigates the increased anthropogenic influence on the within-channel belt sedimentary dynamics in the Rhine delta. To make this investigation, the sedimentary dynamics within the life-cycle of a single channel belt were reconstructed for three key periods of increasing human impact,

Feasibility of electro-osmotic belt filter dewatering technology at pilot scale

CSIR Research Space (South Africa)

Snyman, HG

2000-01-01

Full Text Available -air. The technology was found as sensitive to polyelectrolyte dosages as belt presses. The performance of the electro-osmotic belt filter was sensitive to feed rate, but performed well with non-thickened waste activated sludge (0.61% solids), resulting in cake solids...

Using a Split-belt Treadmill to Evaluate Generalization of Human Locomotor Adaptation.

Science.gov (United States)

Vasudevan, Erin V L; Hamzey, Rami J; Kirk, Eileen M

2017-08-23

Understanding the mechanisms underlying locomotor learning helps researchers and clinicians optimize gait retraining as part of motor rehabilitation. However, studying human locomotor learning can be challenging. During infancy and childhood, the neuromuscular system is quite immature, and it is unlikely that locomotor learning during early stages of development is governed by the same mechanisms as in adulthood. By the time humans reach maturity, they are so proficient at walking that it is difficult to come up with a sufficiently novel task to study de novo locomotor learning. The split-belt treadmill, which has two belts that can drive each leg at a different speed, enables the study of both short- (i.e., immediate) and long-term (i.e., over minutes-days; a form of motor learning) gait modifications in response to a novel change in the walking environment. Individuals can easily be screened for previous exposure to the split-belt treadmill, thus ensuring that all experimental participants have no (or equivalent) prior experience. This paper describes a typical split-belt treadmill adaptation protocol that incorporates testing methods to quantify locomotor learning and generalization of this learning to other walking contexts. A discussion of important considerations for designing split-belt treadmill experiments follows, including factors like treadmill belt speeds, rest breaks, and distractors. Additionally, potential but understudied confounding variables (e.g., arm movements, prior experience) are considered in the discussion.

First Results of Modeling Radiation Belt Electron Dynamics with the SAMI3 Plasmasphere Model

Science.gov (United States)

Komar, C. M.; Glocer, A.; Huba, J.; Fok, M. C. H.; Kang, S. B.; Buzulukova, N.

2017-12-01

The radiation belts were one of the first discoveries of the Space Age some sixty years ago and radiation belt models have been improving since the discovery of the radiation belts. The plasmasphere is one region that has been critically important to determining the dynamics of radiation belt populations. This region of space plays a critical role in describing the distribution of chorus and magnetospheric hiss waves throughout the inner magnetosphere. Both of these waves have been shown to interact with energetic electrons in the radiation belts and can result in the energization or loss of radiation belt electrons. However, radiation belt models have been historically limited in describing the distribution of cold plasmaspheric plasma and have relied on empirically determined plasmasphere models. Some plasmasphere models use an azimuthally symmetric distribution of the plasmasphere which can fail to capture important plasmaspheric dynamics such as the development of plasmaspheric drainage plumes. Previous work have coupled the kinetic bounce-averaged Comprehensive Inner Magnetosphere-Ionosphere (CIMI) model used to model ring current and radiation belt populations with the Block-adaptive Tree Solar wind Roe-type Upwind Scheme (BATSRUS) global magnetohydrodynamic model to self-consistently obtain the magnetospheric magnetic field and ionospheric potential. The present work will utilize this previous coupling and will additionally couple the SAMI3 plasmasphere model to better represent the dynamics on the plasmasphere and its role in determining the distribution of waves throughout the inner magnetosphere. First results on the relevance of chorus, hiss, and ultralow frequency waves on radiation belt electron dynamics will be discussed in context of the June 1st, 2013 storm-time dropout event.

Effect of Thermospheric Neutral Density upon Inner Trapped-belt Proton Flux

Science.gov (United States)

Wilson, Thomas L.; Lodhi, M. A. K.; Diaz, Abel B.

2007-01-01

We wish to point out that a secular change in the Earth's atmospheric neutral density alters charged-particle lifetime in the inner trapped radiation belts, in addition to the changes recently reported as produced by greenhouse gases. Heretofore, changes in neutral density have been of interest primarily because of their effect on the orbital drag of satellites. We extend this to include the orbital lifetime of charged particles in the lower radiation belts. It is known that the charged-belt population is coupled to the neutral density of the atmosphere through changes induced by solar activity, an effect produced by multiple scattering off neutral and ionized atoms along with ionization loss in the thermosphere where charged and neutral populations interact. It will be shown here that trapped-belt flux J is bivariant in energy E and thermospheric neutral density , as J(E,rho). One can conclude that proton lifetimes in these belts are also directly affected by secular changes in the neutral species populating the Earth s thermosphere. This result is a consequence of an intrinsic property of charged-particle flux, that flux is not merely a function of E but is dependent upon density rho when a background of neutrals is present.

Study on the application of permanent magnet synchronous motors in underground belt conveyors

Science.gov (United States)

Ma, S. H.

2017-12-01

This paper analyzes and compares the advantages and disadvantages of several kinds of drive devices of belt conveyors from the angle of energy saving, and summarizes the application advantages and using problems of permanent magnet motor variable frequency drive system in belt conveyors. An example is given to demonstrate the energy saving effect of this system compared with other driving methods. This paper points out the application prospect of permanent magnet motor variable frequency drive system on belt conveyors and other large mining machines in coal mine. This paper is aimed to provide the design direction for the designer and the choice basis for the user on belt conveyor.

Realization methodology for optimal design of steel structures conveyors with hanging belt

Directory of Open Access Journals (Sweden)

Boslovyak P.V.

2016-03-01

Full Text Available Presents the results of optimum design of metal structures of the fixed conveyor with hanging belt. The analysis results optimum design of steel structures of stationary conveyor with hanging belt.

Drug problem in southeast and southwest Asia.

Science.gov (United States)

Kulsudjarit, Kongpetch

2004-10-01

In 2002, the drug problem in Southeast and Southwest Asia was serious, particularly in the production of opium and heroin in Afghanistan, Myanmar, and Laos, the three largest producers of illicit opium in the world. The increasing illicit manufacture of ATS, particularly methamphetamine, in Southeast Asia, mainly in China and Myanmar, was also a major concern. Some reports indicated that ephedrine, used for illicitly producing methamphetamine in Southeast Asia, is diverted and smuggled out of China and India, whereas caffeine, the adulterant used for producing methamphetamine tablets, is mainly smuggled into Myanmar through its border with Thailand. Seizure data showed a dramatic increase in trafficking in MDMA through Southeast Asia. In terms of the drug epidemic, in 2002, cannabis remained overall the main drug of abuse in all of the countries of Southeast and Southwest Asia. Opiates, mainly opium and heroin, were also the drugs of choice except in Thailand, where opiate abuse declined, but ATS was the main drug of abuse due to its low cost and availability. A significant increase in ATS abuse, amphetamine, methamphetamine, and MDMA among the youth who smoked, sniffed, and inhaled them was reported in Cambodia, China, Indonesia, Laos, Myanmar, the Philippines, and Thailand. Injecting drug use among opiate abusers has been identified as the prime cause of the rapid spread of HIV/AIDS in Southeast and Southwest Asia.

The belt pinch - a high-β tokamak with non-circular cross-section

International Nuclear Information System (INIS)

Gruber, O.; Peiry, J.M.; Wilhelm, R.

1975-10-01

The stability behaviour of non-circular plasma cross-sections is discussed on the basis of present known theory. Then the technical arrangement and the preionization of the Belt Pinch is described. The following section deals with the establishment of the non-circular equilibrium and summarizes the essential plasma paramters and the used diagnostic methods. The stability properties of the Belt Pinch, lead to a critical q-value. Finnaly, supporting experiments for the future Belt Pinch programm are presented. (orig./GG) [de

PROPOSALS ON IMPROVING THE EXCAVATION, TRANSPORT AND COAL DEPOSIT, USING THE RUBBER CONVEYOR BELT

Directory of Open Access Journals (Sweden)

Nicoleta-Maria MIHUT

2016-05-01

Full Text Available In this work we make a study of the improvement methods of quantity of material transported by conveyor belt. Determination of discharge of solids entail establish of the parameters of the conveyor belt. As a result, we determine the belt speed who provide maximum discharge of solids materials.

[Use of seat belts and mobile phone while driving in Florence: trend from 2005 to 2009].

Science.gov (United States)

Lorini, Chiara; Pellegrino, Elettra; Mannocci, Federico; Allodi, Guendalina; Indiani, Laura; Mersi, Anna; Petrioli, Giuseppe; Santini, Maria Grazia; Garofalo, Giorgio; Bonaccorsi, Guglielmo

2012-01-01

to evaluate the trend over time of the use of seat belts by drivers and passengers of cars and vans and the use of hand held mobile phone while driving in Florence from 2005 to 2009. DESIGN, SETTING AND PARTICIPANTS AND MAIN OUTCOME MEASURES: direct observations (58,773 vehicles) have been conducted to detect the use of seat belts by occupants of cars and vans, and the use of mobile phone while driving. It has been carried out correlation analysis between the use of the seat belt by occupants of vehicles and between the simultaneous use of this device and mobile phone while driving.Moreover, it has been carried out time series analysis (ARIMA Box Jenkins) of in the prevalence of the use of seat belts by occupants of vehicles observed, of mobile phone by drivers and the trend of the risk to drive using the mobile phone with unfastened seat belt rather than to drive using the mobile phone with fastened seat belt. seat belts were used on average by 75.7% of drivers, 75.5% of front passengers and 25.1% of rear passengers. The average mobile phone use while driving was 4.5%. Drivers most frequently fasten seat belt if front passengers use it and while they do not use mobile phone. The use of seat belts by drivers and front passengers has not changed over time, whereas the use of mobile phone while driving has significantly increased. The prevalence of using mobile phone with unfastened seat belt rather than to use it with fastened seat belt while driving has significantly decreased over the years, indicating an increase in the use of mobile phone, especially among those who fasten the seat belt. it is necessary to plan and realize stronger interventions in the whole area.

Determination of acceleration for belt conveyor speed control in transient operation

NARCIS (Netherlands)

He, D.; Pang, Y.; Lodewijks, G.

2016-01-01

Speed control has been found a feasible mean to reduce the energy consumption of belt conveyors. However, the current research has not taken the determination of the acceleration in transient operation into account sufficiently. With respect to the belt tension rating, demanded safety factor and the

Characteristics of the cold-water belt formed off Soya Warm Current

Science.gov (United States)

Ishizu, Miho; Kitade, Yujiro; Matsuyama, Masaji

2008-12-01

We examined the data obtained by acoustic Doppler current profiler, conductivity-temperature-depth profiler, and expendable bathythermograph observations, which were collected in the summers of 2000, 2001, and 2002, to clarify the characteristics of the cold-water belt (CWB), i.e., lower-temperature water than the surrounding water extending from the southwest coast of Sakhalin along the offshore side of Soya Warm Current (SWC) and to confirm one of the formation mechanisms of the CWB as suggested by our previous study, i.e., the upwelling due to the convergence of bottom Ekman transport off the SWC region. The CWB was observed at about 30 km off the coast, having a thickness of 14 m and a minimum temperature of 12°C at the sea surface. The CWB does not have the specific water mass, but is constituted of three representative water types off the northeast coast of Hokkaido in summer, i.e., SWC water, Fresh Surface Okhotsk Sea Water, and Okhotsk Sea Intermediate Water. In a comparison of the horizontal distributions of current and temperature, the CWB region is found to be advected to the southeast at an average of 40 ± 29% of the maximum current velocity of the SWC. The pumping speed due to the convergence of the bottom Ekman transport is estimated as (1.5-3.0) × 10-4 m s-1. We examined the mixing ratio of the CWB, and the results implied that the water mass of the CWB is advected southeastward and mixes with a water mass upwelling in a different region off SWC.

Geochronology of the Jequie-Itabuna granulitic belt and of the Contendas-Mirante volcano-sedimentary belt

International Nuclear Information System (INIS)

Marinho, Moacyr M.; Barbosa, Johildo S.F.; Sabate, Pierre

1995-01-01

The Jequie-Itabuna Granulitic Belt is divided here into the Jequie-Mutuipe-Maracas Domain and the Atlantic Coast Domain. The paper analyzes the geochronological data from the Jequie-Mutuipe-Maracas Domain in two parts: plutonic rocks equilibrated in granulite facies, including the charno-enderbitic rocks from the Laje-Mutuipe region and the charnockitic rocks from the Maracas region; and ortho- and paraderived rocks metamorphosed in granulite facies, with the data obtained from rocks collected at the Jequie quarry and from homogeneous rocks collected at the western outskirts of the Jequirica town. The available geochronological data for the Atlantic Coast Domain is discussed, and due to the lack of petrologic control of the analyzed rocks, the geological significance of the ages between 2.0 and 2.3 is obtained in several line regressions. The paper identifies the following domains within the Contendas-Mirante volcano-sedimentary belt: the the basement dones, the volcano-sedimentary sequence and the intrusive rocks. The basement domes is the domain of the ancient gray gneisses (ca 3.4 Ga), to TTG (tonalite-trondhjemite-granodiorite) terrains and among the different massifs that crop out in the SE sector of the volcano-sedimentary belt, those of Sete Voltas and Boa Vista/Mata Verde have geochronological data available. The volcano-sedimentary sequence is divided into a lower, a middle and an upper unit and its available isotopic data are analyzed. The item referent to the intrusive rocks deals with the following plutons: The Lagoa Morro da Velha granitoid, the Pe da Serra granite, the Rio Jacare sill and the Transamazonian granites. 31 figs., 5 tabs

Detailed Characteristics of Radiation Belt Electrons Revealed by CSSWE/REPTile Measurements

Science.gov (United States)

Zhang, K.; Li, X.; Schiller, Q.; Gerhardt, D. T.; Millan, R. M.

2016-12-01

The outer radiation belt electrons are highly dynamic. We study the detailed characteristics of the relativistic electrons in the outer belt using measurements from the Colorado Student Space Weather Experiment (CSSWE) mission, a low Earth orbit Cubesat, which transverses the radiation belt four times in one orbit ( 1.5 hr) and has the advantage of measuring the dynamic activities of the electrons including their rapid precipitations. Among the features of the relativistic electrons, we show the measured electron distribution as a function of geomagnetic activities and local magnetic field strength. Moreover, a specific precipitation band, which happened on 19 Jan 2013, is investigated based on the conjunctive measurement of CSSWE and the Balloon Array for Radiation belt Relativistic Electron Losses (BARREL). In this precipitation band event, the net loss of the 0.58 1.63 MeV electrons (L=3.5 6) is estimated to account for 6.84% of the total electron content.

[Strategy programming for acupuncture development along One-Belt-One-Road countries].

Science.gov (United States)

Yang, Yuyang; Shen, Zhixiang; Wu, Zhongchao; Luo, Lu; Liu, Jingyuan; Liu, Baoyan

2017-04-12

Acupuncture has been applied in 183 countries and regions and gradually become a name card as TCM spreads across the world. The international influence of which plays a significant role in enhancing TCM development. The laws and regulations of TCM acupuncture along One-Belt-One-Road countries were compared and analyzed in this article. With comprehensive research and analysis, the international development strategy of acupuncture was rationally proposed. Combined with the historical background of China's national initiative One-Belt-One-Road, the acupuncture was taken as a breakthrough to lead the global spreading of TCM culture and Chinese herbs, so as to enhance China's soft strength, which could further create a fine cultural environment for the economic prosperity of One-Belt-One-Road countries. In addition, the strategy selection for China regarding TCM acupuncture development along One-Belt-One-Road countries was proposed, and the suggestive solution and implementation strategy for the essential missions and significant issues were provided.

Adaptive control of dynamic balance in human gait on a split-belt treadmill.

Science.gov (United States)

Buurke, Tom J W; Lamoth, Claudine J C; Vervoort, Danique; van der Woude, Lucas H V; den Otter, Rob

2018-05-17

Human bipedal gait is inherently unstable and staying upright requires adaptive control of dynamic balance. Little is known about adaptive control of dynamic balance in reaction to long-term, continuous perturbations. We examined how dynamic balance control adapts to a continuous perturbation in gait, by letting people walk faster with one leg than the other on a treadmill with two belts (i.e. split-belt walking). In addition, we assessed whether changes in mediolateral dynamic balance control coincide with changes in energy use during split-belt adaptation. In nine minutes of split-belt gait, mediolateral margins of stability and mediolateral foot roll-off changed during adaptation to the imposed gait asymmetry, especially on the fast side, and returned to baseline during washout. Interestingly, no changes in mediolateral foot placement (i.e. step width) were found during split-belt adaptation. Furthermore, the initial margin of stability and subsequent mediolateral foot roll-off were strongly coupled to maintain mediolateral dynamic balance throughout the gait cycle. Consistent with previous results net metabolic power was reduced during split-belt adaptation, but changes in mediolateral dynamic balance control were not correlated with the reduction of net metabolic power during split-belt adaptation. Overall, this study has shown that a complementary mechanism of relative foot positioning and mediolateral foot roll-off adapts to continuously imposed gait asymmetry to maintain dynamic balance in human bipedal gait. © 2018. Published by The Company of Biologists Ltd.

Start-up of belt conveyors used for haulage of large lumps under difficult climatic conditions

Energy Technology Data Exchange (ETDEWEB)

Drobny, J

1979-01-01

Investigations are discussed carried out by the Research and Development Center for Brown Coal in Most, Czechoslovakia into effects of climate, weather and mass of coal lumps on reliability of belt conveyors in surface mines. Dirt buildup on the driving drums reduces friction and increases belt sliding hazards. Belt wear increases. Driving drum diameter, increased by the buildup, negatively influences load distribution among the electric motors of the drive system. In extreme cases belt wear and irregular load distribution cause belt failures. Methods for buildup removal used in Czechoslovakia and methods for protection of the return side of a conveyor are described. Effects of large mass of coal lumps and ice buildup on large lumps on the risk of belt damage (cuts, punctures etc,) are discussed. Recommendations for design of coal transfer points are made. 2 refs.

The effects of seat belt legislation on road traffic injuries.

Science.gov (United States)

Trinca, G W; Dooley, B J

1977-04-01

The compulsory wearing of seat belts, first introduced in the world in Victoria in 1970, has effectively reduced the number of deaths and injuries by approximately one-third for car occupants involved in motor vehicle crashes. Initially, the legislation did not apply to children under the age of eight years, but in 1975 a further law was introduced banning children from the front seat of any vehicle unless properly harnessed. Seat belts offer the best protection for front seat drivers and passengers involved in frontal impacts, but offer less protection to the recipient of a side impact. Ten per cent of car occupants admitted to hospital after a frontal impact show injuries, mostly minor, directly attibutable to the wearing of seat belts.

Optimal regenerative braking with a push-belt CVT: an experimental study

NARCIS (Netherlands)

Berkel, van K.; Hofman, T.; Vroemen, B.G.; Steinbuch, M.

2010-01-01

This paper describes the approach and the results of efficiency experiments on a push-belt Continuously Variable Transmission (CVT) in a new hybrid drive train. The hybrid drive train uses the push-belt CVT to charge a flywheel, with the kinetic energy of the vehicle during regenerative braking and

Optimal regenerative braking with a push-belt CVT : an experimental study

NARCIS (Netherlands)

van Berkel, K.; Hofman, T.; Vroemen, B.; Steinbuch, M.

2010-01-01

This paper describes the approach and the results of efficiency experiments on a push-belt Continuously Variable Transmission (CVT) in a new hybrid drive train. The hybrid drive train uses the push-belt CVT to “charge” a flywheel, with the kinetic energy of the vehicle during regenerative braking

USGS Southwest Repeat Photography Collection: Kanab Creek, southern Utah and northern Arizona, 1872-2010

Data.gov (United States)

Department of the Interior — The USGS Southwest Repeat Photography Collection (‘Collection’), formerly named the Desert Laboratory Repeat Photography Collection, is now housed by the Southwest...

Efficacy of ultraviolet light exposure against survival of Listeria monocytogenes on conveyor belts.

Science.gov (United States)

Morey, Amit; McKee, Shelly R; Dickson, James S; Singh, Manpreet

2010-06-01

Listeria monocytogenes has been repeatedly isolated from foods and food-processing facilities including food contact surfaces such as conveyor belts (CB). CBs are often difficult to clean and require rigorous sanitation programs for decontamination. Ultraviolet (UV) light has exhibited microbicidal properties on food contact surfaces and this study was conducted to determine the efficacy of UV against L. monocytogenes on CB made of different materials. A four-strain cocktail of L. monocytogenes (serotypes 3A, 4A, 4B, and 4C) was made to give a suspension of approximately 10(7) CFU/mL. CBs made from four different types of materials, (1) Ropanyl DM 8/2 A2 + 04 (belt 1), (2) Volta FRMW-3.0 (belt 2), (3) Volta FRMB-3.0 (belt 3), and (4) Ropanyl DM (belt 4), were inoculated with 1 mL of the four-strain cocktail (approximately 10(7) CFU/mL) of the bacterial suspension. CBs were treated with UV light (254 nm) for 1 and 3 sec at 5.53 and 5.95 mW/cm(2). Three replications of the experiments were conducted. Two-way analysis of variance of survival populations of L. monocytogenes showed that bacterial counts were significantly reduced (p belt types irrespective of UV light intensities and times of exposure. L. monocytogenes populations were reduced (p belts 1, 2, and 3 after exposure to 5.95 mW/cm(2) UV light intensity for 3 sec. L. monocytogenes-inoculated CBs that were exposed to 5.53 mW/cm(2) showed higher (p Belt 4 showed survival populations of L. monocytogenes ranging from 1.42 to 1.73 log(10) CFU/cm(2) after UV light treatment for 1 and 3 sec. UV light can be effectively used to reduce L. monocytogenes contamination on CBs.

Belt, Road, and Circle: The Arctic and Northern Europe in China's Belt and Road Initiative

DEFF Research Database (Denmark)

Nørup Sørensen, Camilla Tenna

2018-01-01

Sørensen offers a much-needed analysis of the how the development of the Belt and Road Initiative (BRI) links to China’s growing interests and ambitions in the Arctic showing how China is using the BRI to further intensify and strengthen relations with the Nordic countries in the Arctic. Conducting...

The atmospheric implications of radiation belt remediation

Directory of Open Access Journals (Sweden)

C. J. Rodger

2006-08-01

Full Text Available High altitude nuclear explosions (HANEs and geomagnetic storms can produce large scale injections of relativistic particles into the inner radiation belts. It is recognised that these large increases in >1 MeV trapped electron fluxes can shorten the operational lifetime of low Earth orbiting satellites, threatening a large, valuable population. Therefore, studies are being undertaken to bring about practical human control of the radiation belts, termed "Radiation Belt Remediation" (RBR. Here we consider the upper atmospheric consequences of an RBR system operating over either 1 or 10 days. The RBR-forced neutral chemistry changes, leading to NO_x enhancements and O_x depletions, are significant during the timescale of the precipitation but are generally not long-lasting. The magnitudes, time-scales, and altitudes of these changes are no more significant than those observed during large solar proton events. In contrast, RBR-operation will lead to unusually intense HF blackouts for about the first half of the operation time, producing large scale disruptions to radio communication and navigation systems. While the neutral atmosphere changes are not particularly important, HF disruptions could be an important area for policy makers to consider, particularly for the remediation of natural injections.

Health impact assessment of the Atlanta BeltLine.

Science.gov (United States)

Ross, Catherine L; Leone de Nie, Karen; Dannenberg, Andrew L; Beck, Laurie F; Marcus, Michelle J; Barringer, Jason

2012-03-01

Although a health impact assessment (HIA) is a tool that can provide decision makers with recommendations to promote positive health impacts and mitigate adverse health impacts of proposed projects and policies, it is not routinely conducted on most major projects or policies. To make health a decision criterion for the Atlanta BeltLine, a multibillion-dollar transit, trails, parks, and redevelopment project. An HIA was conducted in 2005-2007 to anticipate and influence the BeltLine's effect on health determinants. Changes in access and equity, environmental quality, safety, social capital, and physical activity were forecast, and steps to maximize health benefits and reduce negative effects were recommended. Key recommendations included giving priority to the construction of trails and greenspace rather than residential and retail construction, making health an explicit goal in project priority setting, adding a public health professional to decision-making boards, increasing the connectivity between the BeltLine and civic spaces, and ensuring that affordable housing is built. BeltLine project decision makers have incorporated most of the HIA recommendations into the planning process. The HIA was cited in the awarding of additional funds of $7,000,000 for brownfield clean-up and greenspace development. The project is expected to promote the health of local residents more than in the absence of the HIA. This report is one of the first HIAs to tie specific assessment findings to specific recommendations and to identifiable impacts from those recommendations. The lessons learned from this project may help others engaged in similar efforts. Copyright © 2012. Published by Elsevier Inc.

Isotopic evidence for two neoproterozoic high-grade metamorphic events in the Brazilia belt

International Nuclear Information System (INIS)

Pimentel, Marcio Martins; Fuck, Reinhardt Adolfo; Piuzanna, Danielle; Moraes, Renato de; Gioia, Simone Maria C.L

2001-01-01

The Brasilia Belt is part of a Brasiliano/Pan African orogen developed between the Amazon and Sao Francisco cratons. The stabilization of the belt occurred after the last metamorphic event at ca. 620 Ma. There has been increasing geochronological evidence, however, for an older Neoproterozoic metamorphic event at ca. 780 Ma, observed mainly in high grade rocks of three large mafic-ultramafic complexes in the northern part of the belt. In this study we present: (i) new U-Pb and Sm-Nd geochronological data, (ii) a review of the existing metamorphic ages in the Brasilia Belt, and (iii) a discussion on the tectonic model to explain the two Neoproterozoic metamorphic ages (au)

THE HARMONIZATION AND OPTIMIZATION OF DIAGNOSTIC METHODS FOR A BELT CONVEYOR

Directory of Open Access Journals (Sweden)

František HELEBRANT

2012-04-01

Full Text Available The final aim of the project MPO FR‐T11/537 called “The Complex Diagnostic System for the Belt Transport” is a single part custom manufacturing and sale of complex diagnostic system for belt transportation and related services. The output of the project is a prototype of a diagnostic system on a model belt conveyor with prepared and certified diagnostic services and methods including their measurements and other supportive tools. The article will introduce the present state of the solution for the given grant project, especially in the field of suggested work on the diagnostic and supportive methods and other measurements.

Hf Isotope Evidence for Subducted Basalt and Sediment Contributions to the Eastern Trans-Mexican Volcanic Belt

Science.gov (United States)

Cai, Y.; Tuena, A. G.; Capra, L.; Straub, S. M.; Goldstein, S. L.; Langmuir, C. H.

2005-12-01

Magmas generated at thick crust continental arcs often have enriched continental crust-like trace element patterns and Pb-Sr-Nd isotope ratios that are intermediate to both upper mantle and crustal compositions. Thus it is difficult to distinguish between contributions from (a) the subducted basalt and the upper mantle wedge, and (b) subducted sediment and the continental crust. These issues have been the focus of major controversy. Here we show evidence for subduction contributions to lavas in a classic thick crust environment. In Eastern Trans-Mexican Volcanic Belt, the upper continental crust is 30 km to 45 km thick. However, primitive mafic lavas erupt on many sites across the arc. We have analyzed the subducting sediments as represented by DSDP 487, located seaward of the trench, where the lower third of the sediment column has strongly hydrothermal pelagic features and the upper two-thirds is composed of terrigenous sediments. The pelagic sediments have distinctive features that could be used to identify a subduction component in the volcanics, including high REE/Hf, negative Ce anomalies, and Nd-Hf isotopes that lie on the "seawater array" and offset from the "mantle-crust" array. We have focused on a unique series of lavas from volcano Nevado de Toluca, located southwest of Mexico City. These lavas show negative Ce anomalies coupled with low REE/Hf and Zr/Nd ratios. Hf-Nd isotope ratios show a shallow trend compared to the mantle-crust array, consistent with a pelagic component. In addition, Hf isotopes show a striking positive correlation with Ce anomalies that trend toward the pelagic sediment compositions. These and other observations provide clear evidence for a component from subducted sediment in the lavas. In addition, there is a negative correlation of Lu/Hf and Hf isotopes that requires a mixing endmember with MORB-like Hf isotope ratios but with lower than MORB Lu/Hf. This indicates a melt from eclogitic subducted basalt. Compared to other

The forcing of monthly precipitation variability over Southwest Asia during the Boreal cold season

Science.gov (United States)

Hoell, Andrew; Shukla, Shraddhanand; Barlow, Mathew; Cannon, Forest; Kelley, Colin; Funk, Christopher C.

2015-01-01

Southwest Asia, deemed as the region containing the countries of Afghanistan, Iran, Iraq and Pakistan, is water scarce and receives nearly 75% of its annual rainfall during8 the boreal cold season of November-April. The forcing of Southwest Asia precipitation has been previously examined for the entire boreal cold season from the perspective of climate variability originating over the Atlantic and tropical Indo-Pacific Oceans. Here, we examine the inter-monthly differences in precipitation variability over Southwest Asia and the atmospheric conditions directly responsible in forcing monthly November-April precipitation. Seasonally averaged November-April precipitation over Southwest Asia is significantly correlated with sea surface temperature (SST) patterns consistent with Pacific Decadal Variability (PDV), the El Nino-Southern Oscillation (ENSO) and the warming trend of SST (Trend). On the contrary, the precipitation variability during individual months of November-April are unrelated and are correlated with SST signatures that include PDV, ENSO and Trend in different combinations. Despite strong inter-monthly differences in precipitation variability during November- April over Southwest Asia, similar atmospheric circulations, highlighted by a stationary equivalent barotropic Rossby wave centered over Iraq, force the monthly spatial distributions of precipitation. Tropospheric waves on the eastern side of the equivalent barotropic Rossby wave modifies the flux of moisture and advects the mean temperature gradient, resulting in temperature advection that is balanced by vertical motions over Southwest Asia. The forcing of monthly Southwest Asia precipitation by equivalent barotropic Rossby waves is different than the forcing by baroclinic Rossby waves associated with tropically-forced-only modes of climate variability.

Analysis on Climatic Characteristics of the Precipitation Anomaly in Southwest China in Recent 60 Years

Institute of Scientific and Technical Information of China (English)

ZHANG; Rong; PANG; Jing; QIN; Jun

2012-01-01

[Objective]The research aimed to analyze temporal-spatial distribution characteristics of the precipitation anomaly in southwest China from 1951 to 2010. [Method] Based on monthly precipitation data at 44 stations of southwest China and 160 stations of China from 1951 to 2010, by using EOF analysis, wavelet analysis and composite analysis, monthly and seasonal change rules of the precipitation in southwest China were analyzed. Corresponding spatial-temporal distribution characteristics of the precipitation in drought and flood years were studied. Temporal-spatial distribution characteristics of the precipitation anomaly in southwest China in recent 60 years were revealed. [Result]Seasonal distribution of the precipitation in southwest China was uneven and was typical single-peak type. Precipitation concentrated from May to September, and peak appeared in July. In recent years, rainfall in autumn significantly became less, while that in other seasons had no obvious change. Precipitation in summer had the cycle of 14 years, another for 6 years and 3-4 years of periodic oscillations. In wet years, precipitation in southwest China had same phase with that in southern China, and anti-phase with that in the junction of Qinghai, Gansu, Xinjiang and Tibet. In dry years, precipitation in southwest China had same phase with that in the eastern part of northwest China and northern China. [Conclusion]The research provided reference basis for prediction and pre-warning of the precipitation in the zone.

A comparison of safety belt use between commercial and noncommercial light-vehicle occupants.

Science.gov (United States)

Eby, David W; Fordyce, Tiffani A; Vivoda, Jonathon M

2002-05-01

The purpose of this study was to conduct an observational survey of safety belt use to determine the use rate of commercial versus noncommercial light-vehicle occupants. Observations were conducted on front-outboard vehicle occupants in eligible commercial and noncommercial vehicles in Michigan (i.e.. passenger cars, vans/minivans, sport-utility vehicles, and pickup trucks). Commercial vehicles that did not fit into one of the four vehicle type categories, such as tractor-trailers, buses, or heavy trucks, were not included in the survey. The study found that the restraint use rate for commercial light-vehicle occupants was 55.8% statewide. The statewide safety belt use rate for commercial light-vehicles was significantly lower than the rate of 71.2% for noncommercial light-vehicles. The safety belt use rate for commercial vehicles was also significantly different as a function of region, vehicle type, seating position, age group, and road type. The results provide important preliminary data about safety belt use in commercial versus noncommercial light-vehicles and indicate that further effort is needed to promote safety belt use in the commercial light-vehicle occupant population. The study also suggests that additional research is required in order to develop effective programs that address low safety belt use in the commercial light-vehicle occupant population.

Quantitative Simulation of QARBM Challenge Events During Radiation Belt Enhancements

Science.gov (United States)

Li, W.; Ma, Q.; Thorne, R. M.; Bortnik, J.; Chu, X.

2017-12-01

Various physical processes are known to affect energetic electron dynamics in the Earth's radiation belts, but their quantitative effects at different times and locations in space need further investigation. This presentation focuses on discussing the quantitative roles of various physical processes that affect Earth's radiation belt electron dynamics during radiation belt enhancement challenge events (storm-time vs. non-storm-time) selected by the GEM Quantitative Assessment of Radiation Belt Modeling (QARBM) focus group. We construct realistic global distributions of whistler-mode chorus waves, adopt various versions of radial diffusion models (statistical and event-specific), and use the global evolution of other potentially important plasma waves including plasmaspheric hiss, magnetosonic waves, and electromagnetic ion cyclotron waves from all available multi-satellite measurements. These state-of-the-art wave properties and distributions on a global scale are used to calculate diffusion coefficients, that are then adopted as inputs to simulate the dynamical electron evolution using a 3D diffusion simulation during the storm-time and the non-storm-time acceleration events respectively. We explore the similarities and differences in the dominant physical processes that cause radiation belt electron dynamics during the storm-time and non-storm-time acceleration events. The quantitative role of each physical process is determined by comparing against the Van Allen Probes electron observations at different energies, pitch angles, and L-MLT regions. This quantitative comparison further indicates instances when quasilinear theory is sufficient to explain the observed electron dynamics or when nonlinear interaction is required to reproduce the energetic electron evolution observed by the Van Allen Probes.

77 FR 2128 - Southwest Pennsylvania Railroad Company-Acquisition Exemption-Laurel Hill Development Corporation

Science.gov (United States)

2012-01-13

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35584] Southwest Pennsylvania Railroad Company--Acquisition Exemption-- Laurel Hill Development Corporation Southwest... 49 CFR 1150.41 to acquire a number of rail lines now owned by Laurel Hill Development Corporation...

Southwest Energy Innovation Forum: Summary Report

Science.gov (United States)

Ewing Marion Kauffman Foundation, 2010

2010-01-01

The Ewing Marion Kauffman Foundation, Arizona State University (ASU), and U.S. Department of Energy's Advanced Research Projects Agency-Energy (ARPA-E) co-convened a conference on Energy Innovation in the Southwest region of the United States that included participation by entrepreneurs, state government officials, representatives of academia,…

Second longest conveyor belt in UK installed and fully operational

Energy Technology Data Exchange (ETDEWEB)

1981-07-01

A conveyor belt (which after the completion of the Selby complex will be the second longest conveyor belt in the UK) has been installed at the Prince Charles Drift Mine, Prince of Wales Colliery, United Kingdom. The 1706 m conveyor is the sole underground-to-surface conveyor at the Drift Mine, and is powered by a single 2240 kW, 3000 hp drive unit.

Seat belt use to save face: impact on drivers' body region and nature of injury in motor vehicle crashes.

Science.gov (United States)

Han, Guang-Ming; Newmyer, Ashley; Qu, Ming

2015-01-01

Seat belt use is the single most effective way to save lives and reduce injuries in motor vehicle crashes. However, some case reports described seat belt use as a double-edged sword because some injuries are related to seat belt use in motor vehicle crashes. To comprehensively understand the effects of seat belt use, we systemically investigated the association between seat belt use and injuries based on anatomic body region and type of injury in drivers involved in motor vehicle crashes. The injury information was obtained by linking crash reports with hospital discharge data and categorized by using the diagnosis codes based on the Barell injury diagnosis matrix. A total of 10,479 drivers (≥15 years) in passenger vehicles involved in motor vehicle crashes from 2006 to 2011 were included in this study. Seat belt use significantly reduced the proportions of traumatic brain injury (10.4% non-seat belt; 4.1% seat belt) and other head, face, and neck injury (29.3% non-seat belt; 16.6% seat belt) but increased the proportion of spine: thoracic to coccyx injury (17.9% non-seat belt; 35.5% seat belt). Although the proportion of spine: thoracic to coccyx injury was increased in drivers with seat belt use, the severity of injury was decreased, such as fracture (4.2% with seat belt use; 22.0% without seat belt use). Furthermore, the total medical charges decreased due to the change of injury profiles in drivers with seat belt use from a higher percentage of fractures (average cost for per case $26,352) to a higher percentage of sprains and/or strains ($1,897) with spine: thoracic to coccyx injury. This study provide a comprehensive picture for understanding the protective effect of seat belt use on injuries based on anatomic body region and type of injury in drivers involved in motor vehicle crashes.

DEVELOPMENT OF THE TEST METHODS OF THE CONVEYOR BELTS USED IN ENVIRONMENTS ENDANGERED BY EXPLOSION HAZARDS

Directory of Open Access Journals (Sweden)

Florin Adrian PĂUN

2012-05-01

Full Text Available Conveyor belts are used for a long period of time in the industry branches where potentially explosive atmospheres could occur. Dangerous phenomena which can be in direct connection with the use of conveyor belts are the ones regarding: - sparks influence over the coating layer and/or resistance internal structure of the stopped conveyor belt; - propagation of a flame along the length of a conveyor belt that was exposed to a energy source relative high like a fire or due to blockage of a conveyor belt as a result of the driving mechanism still operating, that generate a local heating of the conveyor belt in contact with the driving drum, rollers or any other heating source generated by friction. Determining the safety parameters characteristic of the conveyor belts by employing test methods allows assessment of the safety level as well as certification of their explosion protection quality when used in environments with explosion danger.

Clustering of velocities in a GPS network spanning the Sierra Nevada Block, the northern Walker Lane Belt, and the Central Nevada Seismic Belt, California-Nevada

Science.gov (United States)

Savage, James C.; Simpson, Robert W.

2013-01-01

The deformation across the Sierra Nevada Block, the Walker Lane Belt, and the Central Nevada Seismic Belt (CNSB) between 38.5°N and 40.5°N has been analyzed by clustering GPS velocities to identify coherent blocks. Cluster analysis determines the number of clusters required and assigns the GPS stations to the proper clusters. The clusters are shown on a fault map by symbols located at the positions of the GPS stations, each symbol representing the cluster to which the velocity of that GPS station belongs. Fault systems that separate the clusters are readily identified on such a map. Four significant clusters are identified. Those clusters are strips separated by (from west to east) the Mohawk Valley-Genoa fault system, the Pyramid Lake-Wassuk fault system, and the Central Nevada Seismic Belt. The strain rates within the westernmost three clusters approximate simple right-lateral shear (~13 nstrain/a) across vertical planes roughly parallel to the cluster boundaries. Clustering does not recognize the longitudinal segmentation of the Walker Lane Belt into domains dominated by either northwesterly trending, right-lateral faults or northeasterly trending, left-lateral faults.

The energy-saving design of belt conveyors. Energiesparende Auslegung von Gurtfoerderanlagen

Energy Technology Data Exchange (ETDEWEB)

Greune, A

1989-01-01

The examination of the factors affecting the main resistance on an experimental belt conveyor was carried out by varying the velocity and tension of the belt, the diameter of the carrying idlers and the distance between them, and, for the first time, this examination was performed on different belts with different covers. The influences of the varied parameters for the proportions of main resistance, frictional resistance due to imprint, belt flexing resistance and the rotational resistance of the idlers were recorded with the use of formulae and were graphically represented. For the entire relative main resistance referred to 1 m plant length it was possible to obtain a minimum for a particular combination of parameters, and further recommendations for the energy-saving design of belt conveyors were deduced from this. The joint goals of reducing the load-dependence of the rotational resistance and of improving the reliability of seals, at the same time keeping the number of parts to a minimum and making assembly simple, formed the focal point of examination into the possibilities of improving the construction of carrying idlers. Thus, individual components and alternative constructions were examined on a test bench for measuring the rotational resistance as well as on a test bench for seals, and indications for the design of individual assembly groups were developed from this. (orig.).

77 FR 33560 - Southwest Pennsylvania Railroad Company-Acquisition Exemption-Laurel Hill Development Corporation

Science.gov (United States)

2012-06-06

... Pennsylvania Railroad Company--Acquisition Exemption-- Laurel Hill Development Corporation Southwest... 49 CFR 1150.41 to acquire a 0.66-mile line of railroad owned by Laurel Hill Development Corporation... rail line. Most recently, in Southwest Pennsylvania Railroad Company--Acquisition Exemption--Laurel...

Uniquely Acquired Vintage Seismic Reflection Data Reveal the Stratigraphic and Tectonic History of the Montana Disturbed Belt, USA

Science.gov (United States)

Speece, M. A.; Link, C. A.; Stickney, M.

2011-12-01

In 1983 and 1984 Techco of Denver, Colorado, acquired approximately 302 linear kilometers of two-dimensional (2D) seismic reflection data in Flathead and Lake Counties, Montana, USA, as part of an initiative to identify potential drilling targets beneath the Swan and Whitefish Mountain Ranges and adjacent basins of northwestern Montana. These seismic lines were collected in the Montana Disturbed Belt (MDB) or Montana thrust belt along the western edge of Glacier National Park in mountainous terrain with complicated subsurface structures including thrust faults and folds. These structures formed during the Laramide Orogeny as sedimentary rocks of the Precambrian Belt Supergroup were thrust eastward. Later, during the Cenozoic, high-angle normal faults produced prominent west-facing mountain scarps of the Mission, Swan and Whitefish mountains. The 1983 data set consisted of two profiles of 24-fold (96-channels) Vibroseis data and four profiles of 24-fold (96-channels) helicopter-assisted dynamite data. The dynamite data were collected using the Poulter Method in which explosives were placed on poles and air shots were recorded. The 1983 dynamite profiles extend from southwest to northeast across the Whitefish Mountain Range to the edge of Glacier National Park and the Vibroseis data were collected along nearby roadways. The 1984 data set consists of four profiles of 30-fold (120-channels) helicopter-assisted dynamite data that were also collected using the Poulter Method. The 1984 profiles cross the Swan Mountain Range between Flathead Lake and Glacier National Park. All of these data sets were recently donated to Montana Tech and subsequently recovered from nine-track tape. Conventionally processed seismic stacked sections from the 1980s of these data show evidence of a basement decollement that separates relatively undeformed basement from overlying structures of the MDB. Unfortunately, these data sets have not been processed using modern seismic processing

Compliance with Use of Seat Belt among Commercial Drivers in a Nigerian Community

Directory of Open Access Journals (Sweden)

Oluwole C. Omolase

2012-06-01

Full Text Available AIM: This study aimed at determining compliance with use of seat belt among commercial intercity drivers. METHOD: This is a descriptive cross-sectional study conducted in Owo, South West Nigeria among commercial intercity drivers between June and September, 2009. Ethical clearance was obtained from the Ethical Review Committee of Federal Medical Centre, Owo, Ondo State, Nigeria prior to commencement of this study. The permission of the leadership of Road Transport Workers’ Union was also sought and obtained. Ninety intercity commercial drivers out of the estimated one hundred and sixty intercity commercial drivers in the community were enrolled in this study. Informed consent was obtained from each of the respondents. The data obtained was collated and analyzed with SPSS 15.0.1 statistical soft ware version. RESULTS: Ninety respondents were enrolled in this study. The driving experience of the respondents revealed that most respondents: 53 (58.9% had more than 20 years driving experience. Most respondents;78 (86.7% complied with use of seat belt .The main barrier to compliance with seat belt was short trip;28 (50.9%.Most respondents; 67 (74.4%were in support of penalization of defaulters. The major source of awareness about seat belt was Federal Road Safety Corps;59 (65.6%. CONCLUSION: Most respondents complied with use of seat belt. The major barrier to compliance with seat belt was short trip within the community. The Federal Road Safety Corps should enforce compliance with the use of seat belt most especially within communities. [TAF Prev Med Bull 2012; 11(3.000: 281-286

Seat-belt wearing and driving behavior: an instrumented-vehicle study.

Science.gov (United States)

Janssen, W

1994-04-01

Less-than-expected fatality reductions after seat-belt legislation has been introduced in a jurisdiction may be explained in terms of selective recruitment of parts of the driving population and/or behavioral adaptation by beginning belt users. The present investigation has compared the relative merits of these two hypotheses at the level of individual driver behavior. In the initial study the driving behavior of groups of habitual wearers and nonwearers of the belt was compared. Nonwearers made two trips, one with the belt on and one without the belt. Habitual wearers drove belted only. The main part of the experiment was a 105 km freeway route. Two additional tasks of a somewhat more critical nature, a double lane-change manoeuvre and the performance of a braking manoeuvre in front of a fixed obstacle, were performed after the freeway trips. Factor analysis on 39 variables describing driving behavior on the road and during the additional tasks resulted in five factors. One of these, the factor describing the distribution of driving speed on the freeway, differentiated between nonwearers and wearers (thus yielding support for the selective recruitment hypothesis) as well as between wearing and not wearing the belt by the same drivers (thus yielding support for the behavioral adaptation hypothesis). In the follow-up study the original wearers and nonwearers were assigned to one of four experimental treatments: (i) the promise by the experimenter of a considerable incentive for not having a culpable motor vehicle accident over a period of a year. Half the habitual wearer subjects were assigned to this condition. The expectation was that this group would become more careful in their driving; (ii) a control group, consisting of the remaining habitual wearers; (iii) the agreement between the experimenter and the subject that the latter would buckle up in everyday driving for the year to come--half the habitual nonwearer subjects were assigned to this condition; (iv) a

Availability, functionality, and use of seat belts in Beijing taxis prior to the 2008 Beijing Olympic Games.

Science.gov (United States)

Fleiter, Judy J; Gao, Liping; Qiu, Chen; Shi, Kan

2009-03-01

Use of driver seat belts and availability and functionality of passenger seat belts in a convenience sample of 231 Beijing taxis were examined in the months prior to the 2008 Beijing Olympic Games. Driver and front passenger seat belt use was mandated in China from 2004 to help address the growing public health crisis of road trauma. Results from observations made by in-vehicle passengers revealed that 21.2% of drivers were correctly wearing a belt, approximately half were not, and one third were using the belt in a non-functional way. Over 3/4 of this sample of taxi drivers were unrestrained while working. The percentage of functionally available belts was higher for front than rear passengers (88.3% and 22.9%, respectively). This low rate of belt availability in rear seats calls into question the preparedness of the fleet to cater for the safety needs of foreign visitors to China, particularly those from countries with high levels of restraint use. Factors influencing the use/misuse of seat belts in China remain largely unexplored. Results of this pilot study support further investigations of barriers to using injury prevention mechanisms such as seat belts in less motorised countries.

Composite Microdiscs with a Magnetic Belt

DEFF Research Database (Denmark)

Knaapila, Matti; Høyer, Henrik; Helgesen, Geir

2015-01-01

, the spontaneous aggregation of composite particles is suppressed when dispersed into liquid, which is attributed to the increased particle size, reduced magnetic susceptibility, and the shape of the magnetic domain distribution within the particles (spherical versus a belt). When the composite particles...

76 FR 28767 - Desert Southwest Customer Service Region-Rate Order No. WAPA-152

Science.gov (United States)

2011-05-18

... DEPARTMENT OF ENERGY Western Area Power Administration Desert Southwest Customer Service Region..., Desert Southwest Customer Service Region, Western Area Power Administration, P.O. Box 6457, Phoenix, AZ... Customer Service Region, Western Area Power Administration, P.O. Box 6457, Phoenix, AZ 85005-6457, (602...

Investigation into the effect of common factors on rolling resistance of belt conveyor

Directory of Open Access Journals (Sweden)

Lu Yan

2015-08-01

Full Text Available Since indentation rolling resistance accounts for the major part of total resistance of belt conveyor, it is important to compute it using a proper method during the design and application study of the belt conveyor. First, an approximate formula for computing the indentation rolling resistance is offered. In this formula, a one-dimensional Winkler foundation and a three-parameter viscoelastic Maxwell solid model of the belt backing material are used to determine the resistance to motion of a conveyor belt over idlers. With the help of this formula, the authors analyze the effect of common factors on the rolling resistance. Finally, experiments are carried out under certain condition compared with theoretical analysis. A reasonable correlation exists between the experimental results and the theoretical formulae.

Role of mantle dynamics in rebuilding the Tianshan Orogenic Belt in NW China: A seismic tomographic investigation

Science.gov (United States)

He, Chuansong; Santosh, M.

2018-05-01

The Tianshan orogenic belt, Junggar terrane and Altai terrane are located at the southwestern part of the Central Asian Orogenic Belt (CAOB). Here, we investigate the velocity structure beneath the Xinjiang region in NW China, which includes the Tarim terrane, Tianshan orogenic belt, Junggar terrane and Altai terrane with a view to evaluate the mantle dynamics based on teleseismic data recorded by 103 seismic stations. Our tomographic results show both high and low velocity perturbations beneath the Tianshan orogenic belt. We suggest that the high velocity perturbations beneath this orogenic belt might represent the northward subducted lithosphere of the Tarim Basin and the southward subducted lithosphere of the Junggar Basin. The low velocity structure beneath the Tianshan orogenic belt might represent asthenosphere upwelling that triggered the extensive magmatism which contributed to rebuilding of the Tianshan orogenic belt.

SPECIFIC RESISTANCE AND SPECIFIC INTENSITY OF BELT SANDING OF WOOD

Directory of Open Access Journals (Sweden)

Boleslaw Porankiewicz

2010-06-01

Full Text Available This paper examines and discusses the specific belt sanding resistance K (N·cm-2 and specific belt sanding intensity SI (g·cm-2·min-1, for wood of Pinus sylvestris L., Picea abies L., Quercus robra L., Acer pseudoplatanus L., Alnus glutinosa Gaertn., and Populus Nigra L., by different sanding pressure pS, different sanding grit NG number, and different wood grain angles Phi(v.

Survival in fatal road crashes: body mass index, gender, and safety belt use.

Science.gov (United States)

Sivak, Michael; Schoettle, Brandon; Rupp, Jonathan

2010-02-01

This study evaluated the associations of body mass index (BMI), gender, and use of safety belts with the survival of drivers involved in fatal road crashes. The census data of all U.S. fatal crashes that did not involve pedestrians, bicyclists, or motorcyclists were examined for an 11-year period. If involved in a crash with one or more fatalities, the odds of female drivers being among the fatalities are 1.28 times higher than those of male drivers, and the odds of unbelted drivers being among the fatalities are 5.43 times higher than those of belted drivers. The relationship of survivability to BMI depends on the gender and safety belt use of the driver. For male drivers, increased BMI appears beneficial when safety belts are used but detrimental when not used. For belted female drivers, normal BMI is associated with the lowest odds of being killed, and both increased and decreased BMIs increase the odds. For unbelted female drivers, no reliable trends were present among the BMI categories.

Flexible electrode belt for EIT using nanofiber web dry electrodes.

Science.gov (United States)

Oh, Tong In; Kim, Tae Eui; Yoon, Sun; Kim, Kap Jin; Woo, Eung Je; Sadleir, Rosalind J

2012-10-01

Efficient connection of multiple electrodes to the body for impedance measurement and voltage monitoring applications is of critical importance to measurement quality and practicality. Electrical impedance tomography (EIT) experiments have generally required a cumbersome procedure to attach the multiple electrodes needed in EIT. Once placed, these electrodes must then maintain good contact with the skin during measurements that may last several hours. There is usually also the need to manage the wires that run between the electrodes and the EIT system. These problems become more severe as the number of electrodes increases, and may limit the practicality and portability of this imaging method. There have been several trials describing human-electrode interfaces using configurations such as electrode belts, helmets or rings. In this paper, we describe an electrode belt we developed for long-term EIT monitoring of human lung ventilation. The belt included 16 embossed electrodes that were designed to make good contact with the skin. The electrodes were fabricated using an Ag-plated PVDF nanofiber web and metallic threads. A large contact area and padding were used behind each electrode to improve subject comfort and reduce contact impedances. The electrodes were incorporated, equally spaced, into an elasticated fabric belt. We tested the electrode belt in conjunction with the KHU Mark1 multi-frequency EIT system, and demonstrate time-difference images of phantoms and human subjects during normal breathing and running. We found that the Ag-plated PVDF nanofiber web electrodes were suitable for long-term measurement because of their flexibility and durability. Moreover, the contact impedance and stability of the Ag-plated PVDF nanofiber web electrodes were found to be comparable to similarly tested Ag/AgCl electrodes.

Drivers' opinions of enforcement and incentive strategies to promote safety belt use.

NARCIS (Netherlands)

Hagenzieker, M.P.

2017-01-01

During a nationwide campaign to promote safety belt use among military personnel, a field study was conducted at 12 different military bases in the Netherlands. Amount of enforcement, type of publicity, and incentive strategies were varied among military bases. Observations of safety belt use among

Comparison of Thoracic Injury Risk in Frontal Car Crashes for Occupant Restrained without Belt Load Limiters and Those Restrained with 6 kN and 4 kN Belt Load Limiters.

Science.gov (United States)

Foret-Bruno, J Y; Trosseille, X; Page, Y; Huère, J F; Le Coz, J Y; Bendjellal, F; Diboine, A; Phalempin, T; Villeforceix, D; Baudrit, P; Guillemot, H; Coltat, J C

2001-11-01

In France, as in other countries, accident research studies show that a large proportion of restrained occupants who sustain severe or fatal injuries are involved in frontal impacts (65% and 50%, respectively). In severe frontal impacts with restrained occupants and where intrusion is not preponderant, the oldest occupants very often sustain severe thoracic injuries due to the conventional seat belt. As we have been observing over the last years, we will expect in the coming years developments which include more solidly-built cars, as offset crash test procedures are widely used to evaluate the passive safety of production vehicles. The reduction of intrusion for the most severe frontal impacts, through optimization of car deformation, usually translates into an increase in restraint forces and hence thoracic injury risk with a conventional retractor seat belt for a given impact severity. It is, therefore essential to limit the restraint forces exerted by the seat belt on the thorax in order to reduce the number of road casualties. In order to address thoracic injury risk in frontal impact, Renault cars have been equipped with the Programmed Restraint System (PRS) since 1995. The PRS is a restraint system that combines belt load limitation and pyrotechnic belt pretension. In an initial design of the Programmed Restraint System (PRS1), the belt load limiter was a steel component designed to shear at a given shoulder force, namely 6 kN. It was mounted between the retractor and the lower anchorage point of the belt. The design of the PRS was modified in 1998 (PRS2), but the principle of load limitation was maintained. The threshold was decreased to 4 kN and this lower belt belt-force limiter has been combined with a specially designed airbag. This paper reports on 347 real-world frontal accidents where the EES (Equivalent Energy Speed) ranged from 35 to 75 km/h. One hundred and ninety-eight (198) of these accidents involved cars equipped with the 6 kN load limiter

Tertiary evolution of the Shimanto belt (Japan): A large-scale collision in Early Miocene

Science.gov (United States)

Raimbourg, Hugues; Famin, Vincent; Palazzin, Giulia; Yamaguchi, Asuka; Augier, Romain

2017-07-01

To decipher the Miocene evolution of the Shimanto belt of southwestern Japan, structural and paleothermal studies were carried out in the western area of Shikoku Island. All units constituting the belt, both in its Cretaceous and Tertiary domains, are in average strongly dipping to the NW or SE, while shortening directions deduced from fault kinematics are consistently orientated NNW-SSE. Peak paleotemperatures estimated with Raman spectra of organic matter increase strongly across the southern, Tertiary portion of the belt, in tandem with the development of a steeply dipping metamorphic cleavage. Near the southern tip of Ashizuri Peninsula, the unconformity between accreted strata and fore-arc basin, present along the whole belt, corresponds to a large paleotemperature gap, supporting the occurrence of a major collision in Early Miocene. This tectonic event occurred before the magmatic event that affected the whole belt at 15 Ma. The associated shortening was accommodated in two opposite modes, either localized on regional-scale faults such as the Nobeoka Tectonic Line in Kyushu or distributed through the whole belt as in Shikoku. The reappraisal of this collision leads to reinterpret large-scale seismic refraction profiles of the margins, where the unit underlying the modern accretionary prism is now attributed to an older package of deformed and accreted sedimentary units belonging to the Shimanto belt. When integrated into reconstructions of Philippine Sea Plate motion, the collision corresponds to the oblique collision of a paleo Izu-Bonin-Mariana Arc with Japan in Early Miocene.

Improvement of Statistical Typhoon Rainfall Forecasting with ANN-Based Southwest Monsoon Enhancement

Directory of Open Access Journals (Sweden)

Tsung-Yi Pan

2011-01-01

Full Text Available Typhoon Morakot 2009, with significant southwest monsoon flow, produced a record-breaking rainfall of 2361 mm in 48 hours. This study hopes to improve a statistical typhoon rainfall forecasting method used over the mountain region of Taiwan via an artificial neural network based southwest monsoon enhancement (ANNSME model. Rainfall data collected at two mountain weather stations, ALiShan and YuShan, are analyzed to establish the relation to the southwest monsoon moisture flux which is calculated at a designated sea area southwest of Taiwan. The results show that the moisture flux, with southwest monsoon flow, transported water vapor during the landfall periods of Typhoons Mindulle, Bilis, Fungwong, Kalmaegi, Haitaing and Morakot. Based on the moisture flux, a linear regression is used to identify an effective value of moisture flux as the threshold flux which can enhance mountain rainfall in southwestern Taiwan. In particular, a feedforward neural network (FNN is applied to estimate the residuals from the linear model to the differences between simulated rainfalls by a typhoon rainfall climatology model (TRCM and observations. Consequently, the ANNSME model integrates the effective moisture flux, linear rainfall model and the FNN for residuals. Even with very limited training cases, our results indicate that the ANNSME model is robust and suitable for improvement of TRCM rainfall prediction. The improved prediction of the total rainfall and of the multiple rainfall peaks is important for emergency operation.

Linking the collisional history of the main asteroid belt to its dynamical excitation and depletion

Science.gov (United States)

Bottke, William F.; Durda, Daniel D.; Nesvorný, David; Jedicke, Robert; Morbidelli, Alessandro; Vokrouhlický, David; Levison, Harold F.

2005-12-01

The main belt is believed to have originally contained an Earth mass or more of material, enough to allow the asteroids to accrete on relatively short timescales. The present-day main belt, however, only contains ˜5×10 Earth masses. Numerical simulations suggest that this mass loss can be explained by the dynamical depletion of main belt material via gravitational perturbations from planetary embryos and a newly-formed Jupiter. To explore this scenario, we combined dynamical results from Petit et al. [Petit, J. Morbidelli, A., Chambers, J., 2001. The primordial excitation and clearing of the asteroid belt. Icarus 153, 338-347] with a collisional evolution code capable of tracking how the main belt undergoes comminution and dynamical depletion over 4.6 Gyr [Bottke, W.F., Durda, D., Nesvorny, D., Jedicke, R., Morbidelli, A., Vokrouhlický, D., Levison, H., 2005. The fossilized size distribution of the main asteroid belt. Icarus 175, 111-140]. Our results were constrained by the main belt's size-frequency distribution, the number of asteroid families produced by disruption events from diameter D>100 km parent bodies over the last 3-4 Gyr, the presence of a single large impact crater on Vesta's intact basaltic crust, and the relatively constant lunar and terrestrial impactor flux over the last 3 Gyr. We used our model to set limits on the initial size of the main belt as well as Jupiter's formation time. We find the most likely formation time for Jupiter was 3.3±2.6 Myr after the onset of fragmentation in the main belt. These results are consistent with the estimated mean disk lifetime of 3 Myr predicted by Haisch et al. [Haisch, K.E., Lada, E.A., Lada, C.J., 2001. Disk frequencies and lifetimes in young clusters. Astrophys. J. 553, L153-L156]. The post-accretion main belt population, in the form of diameter D≲1000 km planetesimals, was likely to have been 160±40 times the current main belt's mass. This corresponds to 0.06-0.1 Earth masses, only a small fraction

30 CFR 75.1101 - Deluge-type water sprays, foam generators; main and secondary belt-conveyor drives.

Science.gov (United States)

2010-07-01

... and secondary belt-conveyor drives. 75.1101 Section 75.1101 Mineral Resources MINE SAFETY AND HEALTH... Fire Protection § 75.1101 Deluge-type water sprays, foam generators; main and secondary belt-conveyor... be installed at main and secondary belt-conveyor drives. ...

Watershed regressions for pesticides (WARP) for predicting atrazine concentration in Corn Belt streams

Science.gov (United States)

Stone, Wesley W.; Gilliom, Robert J.

2011-01-01

Watershed Regressions for Pesticides (WARP) models, previously developed for atrazine at the national scale, can be improved for application to the U.S. Corn Belt region by developing region-specific models that include important watershed characteristics that are influential in predicting atrazine concentration statistics within the Corn Belt. WARP models for the Corn Belt (WARP-CB) were developed for predicting annual maximum moving-average (14-, 21-, 30-, 60-, and 90-day durations) and annual 95th-percentile atrazine concentrations in streams of the Corn Belt region. All streams used in development of WARP-CB models drain watersheds with atrazine use intensity greater than 17 kilograms per square kilometer (kg/km2). The WARP-CB models accounted for 53 to 62 percent of the variability in the various concentration statistics among the model-development sites.

Design of belt conveyors in bulk terminal applications. Part 1

Energy Technology Data Exchange (ETDEWEB)

Goodwin, P J; Ramos, C M

1985-10-01

This paper discusses belt conveyors and their development in bulk terminal applications in South Africa. Single- and multi-product terminal philosophy is discussed, including methods of handling different products over the same system and limiting the effects of degradation at transfer points. In Part II, some aspects of belt conveyor design, as well as the results of tests on a chute designed to handle a range of products, will be covered. 23 references.

The Fort Smith radioactive belt, Northwest Territories

International Nuclear Information System (INIS)

Charbonneau, B.W.

1980-01-01

The Fort Smith Belt is an elongate zone, about 200 km x 50 km, extending from the East Arm of Great Slave Lake southerly into northeastern Alberta. The major feature of the belt is that it is one of the most radioactive regions so far recognized in the Canadian Shield. Potassium, uranium, and thorium are all enriched but the greatest increase is in thorium. The dominant rock type underlying the area is a foliated porphyritic granite. This rock contains an average of about 80 ppm thorium (with areas of tens of square kilometres containing up to 200 ppm) and approximately 11 ppm uranium. In places, dark elongate zones rich in biotite, apatite, and opaque minerals within the porphyritic granite may contain an order of magnitude more uranium and thorium than the porphyry. Radioactive minerals within both the porphyry and the dark zones are principally monazite (containing up to 16% ThO 2 ) and isolated grains of uraninite. This foliated porphyritic granite is interpreted as being pre- or syntectonic with respect to the Hudsonian event because its foliation parallels that of the surrounding rocks. There has been subsequent deformation. The second characteristic feature of the Fort Smith Belt is the development of a peripheral zone where eU is enriched relative to eTh correlating mainly with granitoid rocks which surround the thorium-rich area and wherein ratios of eU/eTh exceed 1:2 (compared to the crustal average of 1:4). Uranium may have moved laterally into this marginal area from the thorium-rich porphyry, possibly in a vapour phase. There is a possibility that concentrations of uranium as well as other metals such as Cu, Mo, Zn, Sn, and W could exist in the porphyry and its margin in appropriate chemical and/or structural traps. The radioactive granite rocks of the Fort Smith Belt are adjacent to uranium-thorium occurrences in the nearby Proterozoic Nonacho sediments but whether or not a genetic relationship exists between the two situations is uncertain. (auth)

The scattered disk and hot belt, two sides of the same coin?

Science.gov (United States)

Kavelaars, J. J.; Petit, J.-M.; Gladman, B.; Jone, R. L.; Parker, J.; Taylor, M.

2011-10-01

The Canada-France Ecliptic Plane Survey (CFEPS) and High Latitude Extension (HILat)[] obtained characterized observations of nearly 800 sq.deg. of sky to depths in the range ˜23.5 - 24.4 AB mag, providing a database of nearly 200 trans-neptunian objects (TNOs) with high-precision dynamical classification and known discovery efficiency. Using this database, we find that the high-inclination component of the inner (a 47 AU) belt are well represented by a continuous density distribution coming from a constrained q range (35 < q < 40). This range of peri-center is similar to the range which some researchers associated with the scattered disk. In our modeling of the orbital phase space of the Kuiper belt we find that there is no need for two distinct components (ie. both a scattered disk and a hot component to the classical belt). The historical separation of the high-inclination component of the Kuiper belt into these two distinct structures appears to have been mis-guided.

The Global Statistical Response of the Outer Radiation Belt During Geomagnetic Storms

Science.gov (United States)

Murphy, K. R.; Watt, C. E. J.; Mann, I. R.; Jonathan Rae, I.; Sibeck, D. G.; Boyd, A. J.; Forsyth, C. F.; Turner, D. L.; Claudepierre, S. G.; Baker, D. N.; Spence, H. E.; Reeves, G. D.; Blake, J. B.; Fennell, J.

2018-05-01

Using the total radiation belt electron content calculated from Van Allen Probe phase space density, the time-dependent and global response of the outer radiation belt during storms is statistically studied. Using phase space density reduces the impacts of adiabatic changes in the main phase, allowing a separation of adiabatic and nonadiabatic effects and revealing a clear modality and repeatable sequence of events in storm time radiation belt electron dynamics. This sequence exhibits an important first adiabatic invariant (μ)-dependent behavior in the seed (150 MeV/G), relativistic (1,000 MeV/G), and ultrarelativistic (4,000 MeV/G) populations. The outer radiation belt statistically shows an initial phase dominated by loss followed by a second phase of rapid acceleration, while the seed population shows little loss and immediate enhancement. The time sequence of the transition to the acceleration is also strongly μ dependent and occurs at low μ first, appearing to be repeatable from storm to storm.

Pelvic Belt Effects on Health Outcomes and Functional Parameters of Patients with Sacroiliac Joint Pain

Science.gov (United States)

Hammer, Niels; Möbius, Robert; Schleifenbaum, Stefan; Hammer, Karl-Heinz; Klima, Stefan; Lange, Justin S.; Soisson, Odette; Winkler, Dirk; Milani, Thomas L.

2015-01-01

Introduction The sacroiliac joint (SIJ) is a common source of low back pain. However, clinical and functional signs and symptoms correlating with SIJ pain are widely unknown. Pelvic belts are routinely applied to treat SIJ pain but without sound evidence of their pain-relieving effects. This case-control study compares clinical and functional data of SIJ patients and healthy control subjects and evaluates belt effects on SIJ pain. Methods 17 SIJ patients and 17 healthy controls were included in this prospective study. The short-form 36 survey and the numerical rating scale were used to characterize health-related quality of life in patients in a six-week follow-up and the pain-reducing effects of pelvic belts. Electromyography data were obtained from the gluteus maximus, biceps femoris, rectus femoris and medial vastus. Alterations of muscle activity, variability and gait patterns were compared in patients and controls along with the belts’ effects in a dynamic setting when walking. Results Significant improvements were observed in the short-form 36 survey of the SIJ patients, especially in the physical health subscores. Minor declines were also observed in the numerical rating scale on pain. Belt-related changes of muscle activity and variability were similar in patients and controls with one exception: the rectus femoris activity decreased significantly in patients with belt application when walking. Further belt effects include improved cadence and gait velocity in patients and controls. Conclusions Pelvic belts improve health-related quality of life and are potentially attributed to decreased SIJ-related pain. Belt effects include decreased rectus femoris activity in patients and improved postural steadiness during locomotion. Pelvic belts may therefore be considered as a cost-effective and low-risk treatment of SIJ pain. Trial Registration ClinicalTrials.gov NCT02027038 PMID:26305790

Application of the method finite elements by numerical modeling stress-strain state in conveyor belts

Directory of Open Access Journals (Sweden)

Maras Michal

1997-06-01

Full Text Available Solving problems connected with damaging a conveyor belt at the transfer points is conditioned by knowing laws of this phenomenon. Acquiring the knowledge on this phenomen is possible to be gained either by experimental research or by the numerical model GEM 22, which enables to determine the distribution of stresses and strains in a suitably selected cross-section of a conveyor belt. The paper begins by defining the problem, determining the boundary model conditions and continues by modelling the dynamic force acting on the conveyor belt. In the conclusions of the paper there are given table and graphical results of the numerical modelling aimed at solving the problems connected with the damaging of a conveyor belt. By numerical modelling, in this case the finite element method, in the given way can be realized the parametric studies with changing values of input parameters, especially: - stretching force, - thickness of cover layers of the conveyor belt and strain properties of the rubber, - parameters of the steel cord of the conveyor belt.

Creating and destroying mountain belts in a sandbox (Invited)

Science.gov (United States)

Hernandez, M.

2009-12-01

M. Hernandez-1, L. Cruz-1, G. Hilley-1, J. Malinski-1, W.A. Take-2 1-Department of Geological and Environmental Sciences, Stanford University, Stanford, CA 2-Department of Civil Engineering, Queen's University, Kingston, Canada This study uses a new experimental approach to model the kinematic response of the Aconcagua fold-and-thrust belt to erosion using a deforming sand wedge that is eroded according to a fluvial bedrock incision rule. Our objective is to thoroughly examine the impact that erosion may have had on the kinematics of this fold-and-thrust belt and test the applicability of our approach. Our experimental apparatus allows for a variety of boundary conditions to be applied to the wedge, including constant displacement rate, time-varying displacement rate, constant loading, and time-varying loading. This setting also includes three digital cameras that are connected to the apparatus to monitor the top and one side of the experimental sandbox. In this new experimental approach, as we deform the sand wedge, or mountain belt, we select specific time intervals to calculate, using a Matlab code, the topographic slope derived from our erosion rule. We then use a linear laser to project the calculated topographic slope into the sand wedge and remove any excess of sand with a vacuum cleaner. We then let the wedge continue to deform and repeat the above process. After the end of each experiment, we use Particle Image Velocimetry (PIV) techniques to analyze the movement of the sand particles throughout the experiment. The use of PIV requires the images from all three cameras to be corrected due to lens distortion. We use available software, such as Photoshop, to correct and crop the images. The results of our constant-displacement rate experiments indicate, based on geometric comparisons against natural topographic measurements, that our erosional rule could be satisfactorily applied to sandbox simulations. Each of the main deformational stages identified in the

Multi-pulse orbits and chaotic dynamics in motion of parametrically excited viscoelastic moving belt

International Nuclear Information System (INIS)

Zhang Wei; Yao Minghui

2006-01-01

In this paper, the Shilnikov type multi-pulse orbits and chaotic dynamics of parametrically excited viscoelastic moving belt are studied in detail. Using Kelvin-type viscoelastic constitutive law, the equations of motion for viscoelastic moving belt with the external damping and parametric excitation are given. The four-dimensional averaged equation under the case of primary parametric resonance is obtained by directly using the method of multiple scales and Galerkin's approach to the partial differential governing equation of viscoelastic moving belt. From the averaged equations obtained here, the theory of normal form is used to give the explicit expressions of normal form with a double zero and a pair of pure imaginary eigenvalues. Based on normal form, the energy-phrase method is employed to analyze the global bifurcations and chaotic dynamics in parametrically excited viscoelastic moving belt. The global bifurcation analysis indicates that there exist the heteroclinic bifurcations and the Silnikov type multi-pulse homoclinic orbits in the averaged equation. The results obtained above mean the existence of the chaos for the Smale horseshoe sense in parametrically excited viscoelastic moving belt. The chaotic motions of viscoelastic moving belts are also found by using numerical simulation. A new phenomenon on the multi-pulse jumping orbits is observed from three-dimensional phase space

Nonconformities in real-world fatal crashes--electronic stability control and seat belt reminders.

Science.gov (United States)

Lie, Anders

2012-01-01

Many new safety systems are entering the market. Vision Zero is a safety strategy aiming at the elimination of fatalities and impairing injuries by the use of a holistic model for safe traffic to develop a safe system. The aim of this article is to analyze fatalities in modern cars with respect to the Vision Zero model with special respect to electronic stability control (ESC) systems and modern seat belt reminders (SBRs). The model is used to identify and understand cases where cars with ESC systems lost control and where occupants were unbelted in a seat with seat belt reminders under normal driving conditions. The model for safe traffic was used to analyze in-depth studies of fatal crashes with respect to seat belt use and loss of control. Vehicles from 2003 and later in crashes from January 2004 to mid-2010 were analyzed. The data were analyzed case by case. Cars that were equipped with ESC systems and lost control and occupants not using the seat belt in a seat with a seat belt reminder were considered as nonconformities. A total of 138 fatal crashes involving 152 fatally injured occupants were analyzed. Cars with ESC systems had fewer loss-of-control-relevant cases than cars without ESC systems. Thirteen percent of the ESC-equipped vehicles had loss-of-control-relevant crashes and 36 percent of the cars without ESC systems had loss-of-control-relevant crashes. The analysis indicates that only one car of the 9 equipped with ESC that lost control did it on a road surface with relevant friction when driving within the speed restriction of the road. In seats with seat belt reminders that are in accordance with the European New Car Assessment Programme's (Euro NCAP) protocol, 93 percent of the occupants were using a seat belt. In seats without reminders this number was 74 percent. This study shows that ESC systems result in a very significant reduction in fatal crashes, especially under normal driving conditions. Under extreme driving conditions such as speeding

Cleaning of conveyor belt materials using ultrasound in a thin layer of water.

Science.gov (United States)

Axelsson, L; Holck, A; Rud, I; Samah, D; Tierce, P; Favre, M; Kure, C F

2013-08-01

Cleaning of conveyor belts in the food industry is imperative for preventing the buildup of microorganisms that can contaminate food. New technologies for decreasing water and energy consumption of cleaning systems are desired. Ultrasound can be used for cleaning a wide range of materials. Most commonly, baths containing fairly large amounts of water are used. One possibility to reduce water consumption is to use ultrasonic cavitation in a thin water film on a flat surface, like a conveyor belt. In order to test this possibility, a model system was set up, consisting of an ultrasound transducer/probe with a 70-mm-diameter flat bottom, operating at 19.8 kHz, and contaminated conveyor belt materials in the form of coupons covered with a thin layer of water or water with detergent. Ultrasound was then applied on the water surface at different power levels (from 46 to 260 W), exposure times (10 and 20 s), and distances (2 to 20 mm). The model was used to test two different belt materials with various contamination types, such as biofilms formed by bacteria in carbohydrate- or protein-fat-based soils, dried microorganisms (bacteria, yeasts, and mold spores), and allergens. Ultrasound treatment increased the reduction of bacteria and yeast by 1 to 2 log CFU under the most favorable conditions compared with water or water-detergent controls. The effect was dependent on the type of belt material, the power applied, the exposure time, and the distance between the probe and the belt coupon. Generally, dried microorganisms were more easily removed than biofilms. The effect on mold spores was variable and appeared to be species and material dependent. Spiked allergens were also efficiently removed by using ultrasound. The results in this study pave the way for new cleaning designs for flat conveyor belts, with possibilities for savings of water, detergent, and energy consumption.

A joint econometric analysis of seat belt use and crash-related injury severity.

Science.gov (United States)

Eluru, Naveen; Bhat, Chandra R

2007-09-01

This paper formulates a comprehensive econometric structure that recognizes two important issues in crash-related injury severity analysis. First, the impact of a factor on injury severity may be moderated by various observed and unobserved variables specific to an individual or to a crash. Second, seat belt use is likely to be endogenous to injury severity. That is, it is possible that intrinsically unsafe drivers do not wear seat belts and are the ones likely to be involved in high injury severity crashes because of their unsafe driving habits. The preceding issues are considered in the current research effort through the development of a comprehensive model of seat belt use and injury severity that takes the form of a joint correlated random coefficients binary-ordered response system. To our knowledge, this is the first instance of such a model formulation and application not only in the safety analysis literature, but in the econometrics literature in general. The empirical analysis is based on the 2003 General Estimates System (GES) data base. Several types of variables are considered to explain seat belt use and injury severity levels, including driver characteristics, vehicle characteristics, roadway design attributes, environmental factors, and crash characteristics. The results, in addition to confirming the effects of various explanatory variables, also highlight the importance of (a) considering the moderating effects of unobserved individual/crash-related factors on the determinants of injury severity and (b) seat belt use endogeneity. From a policy standpoint, the results suggest that seat belt non-users, when apprehended in the act, should perhaps be subjected to both a fine (to increase the chances that they wear seat belts) as well as mandatory enrollment in a defensive driving course (to attempt to change their aggressive driving behaviors).

Vibration analysis on automatic take-up device of belt conveyor

Science.gov (United States)

Qin, Tailong; Wei, Jin

2008-10-01

Through introducing application condition of belt conveyor in the modern mining industry, the paper proposed, in the dynamic course of its starting, braking or loading, it would produce moving tension and elastic wave. And analyzed the factors cause the automatic take-up device of belt conveyor vibrating: the take-up device's structure and the elastic wave. Finally the paper proposed the measure to reduce vibration and carried on the modeling and simulation on the tension buffer device.

A new press line concept for conveyor belts; Neues Pressenkonzept fuer Foerdergurte

Energy Technology Data Exchange (ETDEWEB)

Aumueller, Steffen [Siempelkamp Maschinen- und Anlagenbau GmbH und Co. KG, Krefeld (Germany)

2010-06-15

Pressure and temperature are the relevant process parameters for the vulcanisation of rubber products. Particularly, the vulcanisation of large-surface rubber products such as belt conveyors sets large requirements on the mechanical characteristics of the press lines. Siempelkamp Maschinen- und Anlagenbau GmbH and Co. KG (Krefeld, Federal Republic of Germany) is specialized on these requirements. For over 100 years, this company constructs vulcanisation presses for the belt conveyor industry. In the first ten decades, the layout of the press lines according to stiffness and transmission of large forces were in the focus. Till to the late 1980ies, these press lines represented the standard of the belt conveyor industry.

A three-dimensional phase space dynamical model of the Earth's radiation belt

International Nuclear Information System (INIS)

Boscher, D. M.; Beutier, T.; Bourdarie, S.

1996-01-01

A three dimensional phase space model of the Earth's radiation belt is presented. We have taken into account the magnetic and electric radial diffusions, the pitch angle diffusions due to Coulomb interactions and interactions with the plasmaspheric hiss, and the Coulomb drag. First, a steady state of the belt is presented. Two main maxima are obtained, corresponding to the inner and outer parts of the belt. Then, we have modelled a simple injection at the external boundary. The particle transport seems like what was measured aboard satellites. A high energy particle loss is found, by comparing the model results and the measurements. It remains to be explained

Modeling of the outer electron belt during magnetic storms

International Nuclear Information System (INIS)

Desorgher, L.; Buehler, P.; Zehnder, A.; Daly, E.; Adams, L.

1999-01-01

The flux dropout of relativistic electrons in the earth's outer radiation belt, during the main phase of the 26 March 1995 magnetic storm is examined. Outer belt measurements by the Radiation Environment Monitor, REM aboard the STRV-1b satellite are presented to characterize this dropout. In order to simulate the dynamics of the electron belt during the storm main phase a particle tracing code was developed which allows to trace the trajectories of equatorially mirroring electrons in a dynamic magnetospheric electromagnetic field. Two simulations were performed in a non-stationary magnetic field, one taking only the induced electric field into account (fully adiabatic motion), and one with an additional non-stationary convection electric field. The simulations show, that adiabatic deceleration can produce the observed count rate decrease and also the observed inward motion of the count rate peak. The convection electric field causes diffusion, which can take particles from low L values out to the magnetopause and contribute to an additional loss of particles, which is suggested by the observations

Model predictive control based on reduced order models applied to belt conveyor system.

Science.gov (United States)

Chen, Wei; Li, Xin

2016-11-01

In the paper, a model predictive controller based on reduced order model is proposed to control belt conveyor system, which is an electro-mechanics complex system with long visco-elastic body. Firstly, in order to design low-degree controller, the balanced truncation method is used for belt conveyor model reduction. Secondly, MPC algorithm based on reduced order model for belt conveyor system is presented. Because of the error bound between the full-order model and reduced order model, two Kalman state estimators are applied in the control scheme to achieve better system performance. Finally, the simulation experiments are shown that balanced truncation method can significantly reduce the model order with high-accuracy and model predictive control based on reduced-model performs well in controlling the belt conveyor system. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

EFFICIENCY INCREASING OF BELT CONVEYOR’S DRIVE BY CERAMIC LAGGING OF DRIVING PULLEY

Directory of Open Access Journals (Sweden)

Josef JURMAN

2012-04-01

Full Text Available In any point of the belt contact with the drum a relative speed compensation takes place that is carried out by a slippage even when the relevant contact spots are fairly clean and dry. This leads to heat generation that is being absorbed by both materials involved – by the belt as well as by the drum. Unlike the belt, the drum lagging would increase its temperature up to a certain limit that depends on number of factors. When the lagging surface temperature is reaching appx. 60°C some structural changes in the lagging material take place and further rise of temperature can create a risk of belt inflammation and destruction of the driving unit. This can be avoided by lagging the drum with new materials that eliminate any friction on the contact surfaces and that are heat resistant.

Mercury's plasma belt: hybrid simulations results compared to in-situ measurements

Science.gov (United States)

Hercik, D.; Travnicek, P. M.; Schriver, D.; Hellinger, P.

2012-12-01

The presence of plasma belt and trapped particles region in the Mercury's inner magnetosphere has been questionable due to small dimensions of the magnetosphere of Mercury compared to Earth, where these regions are formed. Numerical simulations of the solar wind interaction with Mercury's magnetic field suggested that such a structure could be found also in the vicinity of Mercury. These results has been recently confirmed also by MESSENGER observations. Here we present more detailed analysis of the plasma belt structure and quasi-trapped particle population characteristics and behaviour under different orientations of the interplanetary magnetic field.The plasma belt region is constantly supplied with solar wind protons via magnetospheric flanks and tail current sheet region. Protons inside the plasma belt region are quasi-trapped in the magnetic field of Mercury and perform westward drift along the planet. This region is well separated by a magnetic shell and has higher average temperatures and lower bulk proton current densities than surrounding area. On the day side the population exhibits loss cone distribution function matching the theoretical loss cone angle. Simulations results are also compared to in-situ measurements acquired by MESSENGER MAG and FIPS instruments.

Quantitative Assessment of CRAND Contribution to the Inner Belt Electron Intensity

Science.gov (United States)

Zhang, K.; Li, X.; Selesnick, R.; Schiller, Q. A.; Zhao, H.; Baker, D. N.; Temerin, M. A.

2017-12-01

Following the direct identification and measurements of Cosmic Ray Albedo Neutron Decay (CRAND) produced electrons near the inner edge of the inner belt by Colorado Student Space Weather Experiment (CSSWE)1, we extend the study by addressing more comprehensive questions: (1) what is the relative CRAND contribution to the inner belt compared with electrons injected from further out? (2) How does this relative contribution vary with geomagnetic activity and electron energy? (3) What is the solar cycle dependence of CRAND electrons? In order to answer the above questions, extended data of relativistic electrons in the inner belt are needed for a much longer time period and also finer energy resolution is required. Therefore, we will show results regarding the above questions based on data including other low Earth orbit measurements in addition to CSSWE, such as SAMPEX/PET, DEMETER/IDP, and PROBA-V/EPT. [1] Li, Xinlin, Richard Selesnick, Quintin Schiller, Kun Zhang, Hong Zhao, Daniel Baker, and Michael Temerin (2017), Direct detection of albedo neutron decay electrons at the inner edge of the radiation belt and determination of neutron density in near-Earth space, Nature, under review.

The Behavioral Impact of an Advertising Campaign to Promote Safety Belt Use.

Science.gov (United States)

Cope, John G.; And Others

1988-01-01

Safety belt use with and without addition of an incentive strategy was observed among 8,635 drivers at a drive-through restaurant. During the promotional campaign, average rate of belt use tripled compared to baseline following the introduction of a contingent reward (a large soft drink), and declined during followup. (JW)

Dynamical evolution of V-type photometric candidates in the central and outer main belt asteroids

Science.gov (United States)

Carruba, V.; Huaman, M.

2014-07-01

V-type asteroids are associated with basaltic composition, and are supposed to be fragments of crust of differentiated objects. Most V-type asteroids in the main belt are found in the inner main belt, and are either current members of the Vesta dynamical family (Vestoids), or past members that drifted away. However, several V-type photometric candidates have been recently identified in the central and outer main belt. The origin of this large population of V-type objects is not well understood, since it seems unlikely that Vestoids crossing the 3:1 and 5:2 mean-motion resonance with Jupiter could account for the whole observed population. In this work, we investigated a possible origin of the bodies from local sources, such as the parent bodies of the Eunomia, Merxia, and Agnia asteroid families in the central main belt, and Dembowska, Eos and Magnya asteroid families in the outer main belt. Our results show that dynamical evolution from the parent bodies of the Eunomia and Merxia/Agnia families on timescales of 2 Gyr or more could be responsible for the current orbital location of most of the V-type photometric candidates in the central main belt. Studies for the outer main belt are currently in progress. by the FAPESP (grant 2011/19863-3) and CAPES (grant 15029-12-3) funding agencies.

THE ASTEROID BELT AS A RELIC FROM A CHAOTIC EARLY SOLAR SYSTEM

Energy Technology Data Exchange (ETDEWEB)

Izidoro, André; Raymond, Sean N.; Pierens, Arnaud [Laboratoire d’astrophysique de Bordeaux, Université de Bordeaux, CNRS, B18N, allée Geoffroy Saint-Hilaire, F-33615 Pessac (France); Morbidelli, Alessandro [University of Nice-Sophia Antipolis, CNRS, Observatoire de la Côte d’Azur, Laboratoire Lagrange, BP 4229, F-06304 Nice Cedex 4 (France); Winter, Othon C. [UNESP, Univ. Estadual Paulista—Grupo de Dinâmica Orbital and Planetologia, Guaratinguetá, CEP 12.516-410, São Paulo (Brazil); Nesvorny' , David, E-mail: izidoro.costa@gmail.com [Department of Space Studies, Southwest Research Institute, 1050 Walnut St., Suite 300, Boulder, CO 80302 (United States)

2016-12-10

The orbital structure of the asteroid belt holds a record of the solar system’s dynamical history. The current belt only contains ∼10{sup −3} Earth masses yet the asteroids’ orbits are dynamically excited, with a large spread in eccentricity and inclination. In the context of models of terrestrial planet formation, the belt may have been excited by Jupiter’s orbital migration. The terrestrial planets can also be reproduced without invoking a migrating Jupiter; however, as it requires a severe mass deficit beyond Earth’s orbit, this model systematically under-excites the asteroid belt. Here we show that the orbits of the asteroids may have been excited to their current state if Jupiter’s and Saturn’s early orbits were chaotic. Stochastic variations in the gas giants’ orbits cause resonances to continually jump across the main belt and excite the asteroids’ orbits on a timescale of tens of millions of years. While hydrodynamical simulations show that the gas giants were likely in mean motion resonance at the end of the gaseous disk phase, small perturbations could have driven them into a chaotic but stable state. The gas giants’ current orbits were achieved later, during an instability in the outer solar system. Although it is well known that the present-day solar system exhibits chaotic behavior, our results suggest that the early solar system may also have been chaotic.

Running Mechanics and Metabolic Responses with Water Bottles and Bottle Belt Holders.

Science.gov (United States)

Vincent, Heather K; Zdziarski, Laura A; Fallgatter, Kyle; Negron, Giorgio; Chen, Cong; Leavitt, Trevor; Horodyski, MaryBeth; Wasser, Joseph G; Vincent, Kevin R

2018-01-18

This study determined whether differential kinematics, kinetics, rates of energy use and cardiopulmonary responses occurred during running with water bottles and bottle belt holders compared to running only. Trained runners (N=42; 27.2±6.4 yr) ran on an instrumented treadmill for four conditions in a randomized order: 1) control run (CON); 2) hand-held full water bottle (FULL, 16.9 fluid oz; 454 g); 3) hand-held half-full water bottle (HALF, 8.4 fluid oz.; 227 g); and 4) waist-worn bottle belt holder (BELT; hydration belt; 676 g). Gas exchange was measured using a portable gas analyzer. Kinetic and kinematic responses were determined via standard 3D videographic techniques. Interactions of limb side (right, left) by study condition (CON, FULL, HALF, BELT) were tested for rates of oxygen use and energy expenditure, and kinematic and kinetic parameters. No significant limb side × condition interactions existed for rates of oxygen use or energy expenditure. A significant interaction occurred with sagittal elbow flexion (pwater by hand or on the waist does not significantly change kinematics of running motion, rates of oxygen use and energy expenditure or cardiopulmonary measures over short durations. Runners are likely making adjustments to joint moments and powers that preserve balance and protect the lower extremity joints while maintaining the rates of oxygen use and energy expenditure.

Triple junction orogeny: tectonic evolution of the Pan-African Northern Damara Belt, Namibia

Science.gov (United States)

Lehmann, Jérémie; Saalmann, Kerstin; Naydenov, Kalin V.; Milani, Lorenzo; Charlesworth, Eugene G.; Kinnaird, Judith A.; Frei, Dirk; Kramers, Jan D.; Zwingmann, Horst

2014-05-01

Trench-trench-trench triple junctions are generally geometrically and kinematically unstable and therefore can result at the latest stages in complicated collisional orogenic belts. In such geodynamic sites, mechanism and timescale of deformations that accommodate convergence and final assembly of the three colliding continental plates are poorly studied. In western Namibia, Pan-African convergence of three cratonic blocks led to pene-contemporaneous closure of two highly oblique oceanic domains and formation of the triple junction Damara Orogen where the NE-striking Damara Belt abuts to the west against the NNW-striking Kaoko-Gariep Belt. Detailed description of structures and microstructures associated with remote sensing analysis, and dating of individual deformation events by means of K-Ar, Ar-Ar (micas) and U-Pb (zircon) isotopic studies from the Northern Damara Belt provide robust constraints on the tectonic evolution of this palaeo-triple junction orogeny. There, passive margin sequences of the Neoproterozoic ocean were polydeformed and polymetamorphosed to the biotite zone of the greenschist facies to up to granulite facies and anatexis towards the southern migmatitic core of the Central Damara Belt. Subtle relict structures and fold pattern analyses reveal the existence of an early D1 N-S shortening event, tentatively dated between ~635 Ma and ~580 Ma using published data. D1 structures were almost obliterated by pervasive and major D2 E-W coaxial shortening, related to the closure of the Kaoko-Gariep oceanic domain and subsequent formation of the NNW-striking Kaoko-Gariep Belt to the west of the study area. Early, km-scale D1 E-W trending steep folds were refolded during this D2 event, producing either Type I or Type II fold interference patterns visible from space. The D2 E-W convergence could have lasted until ~533 Ma based on published and new U-Pb ages. The final D3 NW-SE convergence in the northernmost Damara Belt produced a NE-striking deformation

Studi Pengaruh Ukuran Butir Dan Tingkat Kelembaban Pasir Terhadap Performansi Belt Conveyor Pada Pabrik Pembuatan Tiang Beton

OpenAIRE

Depari, Prianto

2010-01-01

Pabrik pembuatan tiang beton yang menggunakan belt conveyor sebagai alat transportasi material yang berbentuk bulk. Material pasir adalah salah satu contoh material bulk, yang diangkut dengan belt conveyor untuk proses mix bahan baku dari beton seperti kerikil, semen, agregat dan lain-lain. Penggunaan belt conveyor ini akan meningkatkan efisiensi kerja dari pabrik pembuatan beton. Performansi belt conveyor tersebut perlu diidentifikasian secara baik dan benar. Identifikasi dilakukan dengan be...

Kuiper Belt Dust Grains as a Source of Interplanetary Dust Particles

Science.gov (United States)

Liou, Jer-Chyi; Zook, Herbert A.; Dermott, Stanley F.

1996-01-01

The recent discovery of the so-called Kuiper belt objects has prompted the idea that these objects produce dust grains that may contribute significantly to the interplanetary dust population. In this paper, the orbital evolution of dust grains, of diameters 1 to 9 microns, that originate in the region of the Kuiper belt is studied by means of direct numerical integration. Gravitational forces of the Sun and planets, solar radiation pressure, as well as Poynting-Robertson drag and solar wind drag are included. The interactions between charged dust grains and solar magnetic field are not considered in the model. Because of the effects of drag forces, small dust grains will spiral toward the Sun once they are released from their large parent bodies. This motion leads dust grains to pass by planets as well as encounter numerous mean motion resonances associated with planets. Our results show that about 80% of the Kuiper belt grains are ejected from the Solar System by the giant planets, while the remaining 20% of the grains evolve all the way to the Sun. Surprisingly, the latter dust grains have small orbital eccentricities and inclinations when they cross the orbit of the Earth. This makes them behave more like asteroidal than cometary-type dust particles. This also enhances their chances of being captured by the Earth and makes them a possible source of the collected interplanetary dust particles; in particular, they represent a possible source that brings primitive/organic materials from the outer Solar System to the Earth. When collisions with interstellar dust grains are considered, however, Kuiper belt dust grains around 9 microns appear likely to be collisionally shattered before they can evolve toward the inner part of the Solar System. The collision destruction can be applied to Kuiper belt grains up to about 50 microns. Therefore, Kuiper belt dust grains within this range may not be a significant part of the interplanetary dust complex in the inner Solar

Planck intermediate results. XII: Diffuse Galactic components in the Gould Belt System

DEFF Research Database (Denmark)

Planck Collaboration,; Ade, P. A. R.; Aghanim, N.

2013-01-01

We perform an analysis of the diffuse low-frequency Galactic components in the Southern part of the Gould Belt system (130^\\circ\\leq l\\leq 230^\\circ and -50^\\circ\\leq b\\leq -10^\\circ). Strong ultra-violet (UV) flux coming from the Gould Belt super-association is responsible for bright diffuse...

Pattern of seat belt use and its associated factors among taxi drivers ...

African Journals Online (AJOL)

Objective: Road traffic injuries constitute a major public health concern that demands effective interventions. Use of car seat belts is recommended as an effective intervention to reduce serious and fatal road traffic injuries. The study intended to investigate the pattern of seat belt use and its correlates among taxi drivers in ...

Measurement and monitoring of electrocardiogram belt tension in premature infants for assessment of respiratory function

Directory of Open Access Journals (Sweden)

Hegyi Thomas

2007-04-01

Full Text Available Abstract Background Monitoring of the electrocardiogram (ECG in premature infants with conventional adhesive-backed electrodes can harm their sensitive skin. Use of an electrode belt prevents skin irritation, but the effect of belt pressure on respiratory function is unknown. A strain gauge sensor is described which measures applied belt tension. Method The device frame was comprised of an aluminum housing and slide to minimize the device weight. Velcro tabs connected housing and slide to opposite tabs located at the electrode belt ends. The slide was connected to a leaf spring, to which were bonded two piezoresistive transducers in a half-bridge circuit configuration. The device was tested for linearity and calibrated. The effect on infant respiratory function of constant belt tension in the normal range (30 g–90 g was determined. Results The mechanical response to a step input was second order (fn = 401 Hz, ζ = 0.08. The relationship between applied tension and output voltage was linear in the range 25–225 gm of applied tension (r2 = 0.99. Measured device sensitivity was 2.18 mV/gm tension using a 5 V bridge excitation voltage. When belt tension was increased in the normal range from 30 gm to 90 gm, there was no significant change in heart rate and most respiratory functions during monitoring. At an intermediate level of tension of 50 gm, pulmonary resistance and work of breathing significantly decreased. Conclusion The mechanical and electrical design of a device for monitoring electrocardiogram electrode belt tension is described. Within the typical range of application tension, cardiovascular and respiratory function are not substantially negatively affected by electrode belt force.

Measurement and monitoring of electrocardiogram belt tension in premature infants for assessment of respiratory function.

Science.gov (United States)

Ciaccio, Edward J; Hiatt, Mark; Hegyi, Thomas; Drzewiecki, Gary M

2007-04-19

Monitoring of the electrocardiogram (ECG) in premature infants with conventional adhesive-backed electrodes can harm their sensitive skin. Use of an electrode belt prevents skin irritation, but the effect of belt pressure on respiratory function is unknown. A strain gauge sensor is described which measures applied belt tension. The device frame was comprised of an aluminum housing and slide to minimize the device weight. Velcro tabs connected housing and slide to opposite tabs located at the electrode belt ends. The slide was connected to a leaf spring, to which were bonded two piezoresistive transducers in a half-bridge circuit configuration. The device was tested for linearity and calibrated. The effect on infant respiratory function of constant belt tension in the normal range (30 g-90 g) was determined. The mechanical response to a step input was second order (fn = 401 Hz, zeta = 0.08). The relationship between applied tension and output voltage was linear in the range 25-225 gm of applied tension (r2 = 0.99). Measured device sensitivity was 2.18 mV/gm tension using a 5 V bridge excitation voltage. When belt tension was increased in the normal range from 30 gm to 90 gm, there was no significant change in heart rate and most respiratory functions during monitoring. At an intermediate level of tension of 50 gm, pulmonary resistance and work of breathing significantly decreased. The mechanical and electrical design of a device for monitoring electrocardiogram electrode belt tension is described. Within the typical range of application tension, cardiovascular and respiratory function are not substantially negatively affected by electrode belt force.

Shallow-Water Benthic Habitats of Southwest Puerto Rico

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Shallow-water (<30m) benthic habitat maps of the nearshore marine environment of two areas in Southwest Puerto Rico (PR), including the Guanica Bay/La Parguera...

ALT-II toroidal belt limiter biasing experiments on TEXTOR

International Nuclear Information System (INIS)

Doerner, R.; Boedo, J.A.; Gray, D.S.

1991-01-01

Edge electric fields have been related to H-mode-like behaviour. The experiments reported here are an attempt to control the SOL profiles by electrostatic biasing of the full toroidal-belt limiter ALT-II. The specific goals are: influencing the edge particle flows, particle removal, power deposition and the global confinement. The ALT-II pump limiter is a full toroidal belt located at 45 o below the outer midplane and consisting of eight graphite covered blades which can be independently biased. Particle scoops located behind the limiter neutralize and direct the incoming plasma into the pumping ducts. (author) 5 refs., 3 figs

Crustal scale geometry of the Zagros fold–thrust belt, Iran

OpenAIRE

McQuarrie, Nadine

2004-01-01

Balanced cross-sections across the Zagros fold–thrust belt in Iran are used to analyze the geometry of deformation within the sedimentary cover rocks, and to test the hypothesis of basement involved thrusting throughout the fold–thrust belt. Although the Zagros deformation front is a relatively rectilinear feature, the sinuous map-view morphology of the mountain front is a result of a 6 km structural step in the regional elevation of the Asmari Limestone that produces a pronounced step in top...

Energy optimization of conveyor belts at RWE Power AG; Energetische Optimierung von Foerdergurten bei der RWE Power AG

Energy Technology Data Exchange (ETDEWEB)

Ziegler, Manfred [RWE Power International RE GmbH, Koeln (Germany). Gewinnungs- und Foerdertechnik

2009-11-15

Influencing horizontal resistance to motion has the greatest leverage effect in terms of reducing the power requirements of belt conveyors. The selection of a suitable conveyor belt with optimized running resistance enables substantial cost savings, both with regard to current energy consumption and with regard to the drive power to be installed. Measurements carried out on standard conveyor belts used by RWE Power show differences of up to 30 % in the principal resistance. A method to reliably predict the energy properties of a conveyor belt by means of small specimens was developed. In addition, the requirements to be met in terms of mechanical endurance of a belt depending on conveyor configuration, which set limits to the development of energy-saving belts suitable for operation, will be outlined. To resolve this conflict of aims, conveyor engineers are given concrete tips on the design of belt conveyor systems. (orig.)

Sm-Nd age of ultrabasite-basite massifs of east part of Baikal-Mujya ophiolite belt

International Nuclear Information System (INIS)

Izokh, A.Eh.; Gibsher, A.S.; Zhuravlev, D.Z.; Balykin, P.A.

1998-01-01

Two stratified ultrabasite-basite massifs of the Urals mountains were selected for isotope-geochemical studies. The intrusives, related to plutonic members of the island-arc associations, were used for dating. The Sm-Nd method indicated that one more belt, namely the Vend belt, is taking shape in the Baikal-Mujya tectonic collage alongside with the later Riphean (pre-Baikal) episubconduction belt of stratified intrusives [ru

Dynamics of Quasi-Electrostatic Whistler waves in Earth's Radiation belts

Science.gov (United States)

Goyal, R.; Sharma, R. P.; Gupta, D. N.

2017-12-01

A numerical model is proposed to study the dynamics of high amplitude quasi-electrostatic whistler waves propagating near resonance cone angle and their interaction with finite frequency kinetic Alfvén waves (KAWs) in Earth's radiation belts. The quasi-electrostatic character of whistlers is narrated by dynamics of wave propagating near resonance cone. A high amplitude whistler wave packet is obtained using the present analysis which has also been observed by S/WAVES instrument onboard STEREO. The numerical simulation technique employed to study the dynamics, leads to localization (channelling) of waves as well as turbulent spectrum suggesting the transfer of wave energy over a range of frequencies. The turbulent spectrum also indicates the presence of quasi-electrostatic whistlers and density fluctuations associated with KAW in radiation belts plasma. The ponderomotive force of pump quasi-electrostatic whistlers (high frequency) is used to excite relatively much lower frequency waves (KAWs). The wave localization and steeper spectra could be responsible for particle energization or heating in radiation belts.

Slim belt induced morphea-Price paid for a slimmer look

Directory of Open Access Journals (Sweden)

Tasleem Arif

2015-07-01

Full Text Available Morphea, also known as localized scleroderma, encompasses a group of distinct conditions characterized by sclerosis of the skin and the underlying tissues. Many triggering factors have been implicated in the development of morphea like trauma, immobilization, bacille Calmette–Guérin (BCG vaccination, injections of vitamin K, mechanical compression from clothing, etc. but slim belt as a cause of morphea has not been previously reported to the best of our knowledge. We report a 28 year old married obese woman who developed a shiny brownish indurated plaque over the abdomen after three months of use of a slim belt for her obesity. Skin biopsy was consistent with the diagnosis of morphea. She was prescribed topical tacrolimus 0.1% ointment and improved with course of time. The present case illustrates the first description of morphea as a result of use of slim belt which has not been previously reported in the literature.

Vertical climatic belts in the Tatra Mountains in the light of current climate change

Science.gov (United States)

Łupikasza, Ewa; Szypuła, Bartłomiej

2018-04-01

The paper discusses temporal changes in the configuration of vertical climatic belts in the Tatra Mountains as a result of current climate change. Meteorological stations are scarce in the Tatra Mountains; therefore, we modelled decadal air temperatures using existing data from 20 meteorological stations and the relationship between air temperature and altitude. Air temperature was modelled separately for northern and southern slopes and for convex and concave landforms. Decadal air temperatures were additionally used to delineate five climatic belts previously distinguished by Hess on the basis of threshold values of annual air temperature. The spatial extent and location of the borderline isotherms of 6, 4, 2, 0, and - 2 °C for four decades, including 1951-1960, 1981-1990, 1991-2000, and 2001-2010, were compared. Significant warming in the Tatra Mountains, uniform in the vertical profile, started at the beginning of the 1980s and led to clear changes in the extent and location of the vertical climatic belts delineated on the basis of annual air temperature. The uphill shift of the borderline isotherms was more prominent on southern than on northern slopes. The highest rate of changes in the extent of the climatic belts was found above the isotherm of 0 °C (moderately cold and cold belts). The cold belt dramatically diminished in extent over the research period.

New stratigraphic proposal for supra crustal the Dom Feliciano Belt ( Proterozoic , Uruguay )

International Nuclear Information System (INIS)

Preciozzi, F.; Sanchez Bettucci, L.; Oyhantcabal, P.; Pecoits, E.; Aubet, N.; Peel, E.; Basei, M.

2005-01-01

Dom Feliciano Belt (Fragoso Cesar 1980) is represented in Uruguay so Preciozzi et to the. (1991) defined as Dionisio Blade Belt. It brings together all affected units by metamorphism and deformation during the Brasiliano (sensu Almeida et al. 1973) and magmatism in the same age range, which develops constituting a belt in southeastern Uruguay. Various supra crustal successions have been recognized in the Western domain of this belt in Uruguay, namely Fm. Zanja del Tigre (Sanchez-Bettucci 1998), Lavalleja Group (Bossi 1966), Arroyo del Soldado Group (Gaucher et al. 1996) and Formations Playa Hermosa (Masquelin and Sanchez Bettucci 1993) and Las Ventanas (Midot 1984), among others. The Group has been Lavalleja correlated with Porongos Group and the Brazilian Brusque Metamorphic Complex (Hasui et al. 1975; Silva and Dias 1981). This group has a granitic basement-probably associated gnéissico to Block Valentines (Preciozzi et al. 1979) and the Land Pavas, aged Paleoproterozoicas and Archean (Hartmann et al. 2001). It comprises varied lithologies, metasedimentary; metavolcanic acid; basic and metagabbros metavolcanic

ASPECTS ON THE ACTUAL LEVEL OF EDUCATIONAL DEVELOPMENT AT THE SOUTH-WEST REGION OLTENIA

Directory of Open Access Journals (Sweden)

CHIRCULESCU MARIA FELICIA

2017-08-01

Full Text Available Due to the complexity of the educational sector, the work is topical, even though over time there have been many concerns regarding its education and development and the correlation between the level of educational development and the level of economic development. The aim of the paper is to analyze the educational development at the level of the South-West Oltenia region over the period 2010-2015, thus using the statistical series for the mentioned timeframe we analyzed the evolution of the number of educational units in the South-West Oltenia region And the evolution of the school population in the South-West Oltenia region. Thus, the objective of the paper is enshrined in the overall objective of Romania, namely to reduce the economic and social development disparities between Romania and other EU Member States. The results of the analysis carried out by the two indicators, the number of educational units in the South-West Oltenia region and the number of the school population at the level of the South-West Oltenia region indicate that the number of educational units in the period 2010-2015 decreased by 4.28% And the number of the school population by 14.67%.

Design of belt conveyor electric control device based on CC-link bus

Science.gov (United States)

Chen, Goufen; Zhan, Minhua; Li, Jiehua

2016-01-01

In view of problem of the existing coal mine belt conveyor is no field bus communication function, two levels belt conveyor electric control system design is proposed based on field bus. Two-stage belt conveyor electric control system consists of operation platform, PLC control unit, various sensors, alarm device and the water spraying device. The error protection is realized by PLC programming, made use of CC-Link bus technology, the data share and the cooperative control came true between host station and slave station. The real-time monitor was achieved by the touch screen program. Practical application shows that the system can ensure the coalmine production, and improve the automatic level of the coalmine transport equipment.

Review of Dynamic Modeling and Simulation of Large Scale Belt Conveyor System

Science.gov (United States)

He, Qing; Li, Hong

Belt conveyor is one of the most important devices to transport bulk-solid material for long distance. Dynamic analysis is the key to decide whether the design is rational in technique, safe and reliable in running, feasible in economy. It is very important to study dynamic properties, improve efficiency and productivity, guarantee conveyor safe, reliable and stable running. The dynamic researches and applications of large scale belt conveyor are discussed. The main research topics, the state-of-the-art of dynamic researches on belt conveyor are analyzed. The main future works focus on dynamic analysis, modeling and simulation of main components and whole system, nonlinear modeling, simulation and vibration analysis of large scale conveyor system.

Device for determining the content of bulk materials on conveyor belts

International Nuclear Information System (INIS)

Fritsche, D.

1983-01-01

On the basis of the forward scattering of photon radiation the invention is aimed at determining the content of bulk material, in particular the ash content of lignite, independently of the height of the material conveyed by belts. This could be achieved by making the radiation source support movable, so that the distance between source and conveyor belt is variable and adaptable to the mean height of the bulk material

The Tintina Gold Belt - A global perspective

Science.gov (United States)

Goldfarb, Richard J.; Hart, Craig J.R.; Miller, Marti L.; Miller, Lance D.; Farmer, G. Lang; Groves, David I.; Tucker, Terry L.; Smith, Moira T.

2000-01-01

The so-called Tintina Gold Belt extends for more than 1000 km along the length of the northern North American Cordillera. Middle to Late Cretaceous Au deposits within the belt have various similar characteristics, among which are a spatial and temporal association with magmatism; Bi-W-Te signatures in deposits hosted by granitod stocks and As-Sb signatures where hosted by sedimentary rocks and dyke systems; and δ180 values consistently > 12 per mil for Au-bearing quartz. Nevertheless significant differences in structural styles, levels of deposit emplacement, ore-fluid chemistry, and Au grades suggest that the characteristics represent a broad range of deposit types. Many of these are best classified as orogenic Au deposits in the Yukon-Tanana terrane, as epithermal and porphyry-style Au deposits in the Kuskokwim region, and as Au-bearing, granite-related veins and stockworks, replacements, and skarns, as well as associated polymetallic lodes, in central Yukon. The diverse types of Au deposits and associated plutons of the Tintina Gold Belt collectively define a 45-m.y.-long period of arc magmatism that migrated northwesterly, for about 1000 km, across the active collisional margin of Cretaceous northwestern North America. The initiation of fluid flow and plutonism in Albian time seems to correlate with the onset of oblique subduction and dextral strike-slip on the Denali-Farewell, Tintina-Kaltag, and related fault systems. Initial Au-vein formation and subduction-related magmatism at about 115-110 Ma (e.g., including the Goodpaster and Fortymile districts), within the seaward side of the Yukon-Tanana terrane, correlate with the arrival of the Wrangellia superterrane off the continental margin. Dextral translation of the allochthonous Wrangellia block was associated with the migration of the thermal pulse to the northwest at about 95-90 Ma. Orogenic (or so­ called mesotherrnal) and granitoid-related Au deposits formed across the width of the Yukon

Enforcement or incentives ? : promoting safety belt use among military personnel in the Netherlands.

NARCIS (Netherlands)

Hagenzieker, M.P.

1991-01-01

During a nationwide campaign to promote safety belt use among military personnel, a field study was conducted at 12 different military bases in the netherlands. Amount of enforcement, type of publicity, and incentive strategies were varied among military bases. Observations of safety belt use among

The geology of the gold deposits of Prestea gold belt of Ghana ...

African Journals Online (AJOL)

This paper presents the geology of the gold deposits along the Prestea gold belt of Ghana to assist exploration work for new orebodies along the belt. Prestea district is the third largest gold producer in West Africa after Obuasi and Tarkwa districts (over 250 metric tonnes Au during the last century). The gold deposits are ...

2005/2006 Southwest Florida Water Management District (SWFWMD) Lidar: Peace River South (including Carter Creek)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Light Detection and Ranging (LiDAR) LAS dataset is a survey of select areas within Southwest Florida. These data were produced for the Southwest Florida Water...

Conveyor belt nuclear weighing machine

International Nuclear Information System (INIS)

Anon.

1977-01-01

In many industries the flow of materials on conveyor belts must be measured and controlled. Electromechanical weighing devices have high accuracy but are complicated and expensive to install and maintain. For many applications the nuclear weighing machine has sufficient accuracy but is considerably simpler, cheaper and more robust and is easier to maintain. The rating and performance of a gamma ray balance on the mar ket are detailed. (P.G.R.)

75 FR 61790 - Capital Southwest Corporation; Notice of Application

Science.gov (United States)

2010-10-06

... makes available significant managerial assistance with respect to the issuers of such securities. 2... Accounting Standards Board for operating companies. In addition, Capital Southwest will comply with the...

30 CFR 57.4263 - Underground belt conveyors.

Science.gov (United States)

2010-07-01

....4263 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Fire Prevention and Control Firefighting Equipment § 57.4263 Underground belt conveyors. Fire protection shall be...

Evaluation of Criteria for the Detection of Fires in Underground Conveyor Belt Haulageways.

Science.gov (United States)

Litton, Charles D; Perera, Inoka Eranda

2012-07-01

Large-scale experiments were conducted in an above-ground gallery to simulate typical fires that develop along conveyor belt transport systems within underground coal mines. In the experiments, electrical strip heaters, imbedded ~5 cm below the top surface of a large mass of coal rubble, were used to ignite the coal, producing an open flame. The flaming coal mass subsequently ignited 1.83-meter-wide conveyor belts located approximately 0.30 m above the coal surface. Gas samples were drawn through an averaging probe located approximately 20 m downstream of the coal for continuous measurement of CO, CO 2 , and O 2 as the fire progressed through the stages of smoldering coal, flaming coal, and flaming conveyor belt. Also located approximately 20 m from the fire origin and approximately 0.5 m below the roof of the gallery were two commercially available smoke detectors, a light obscuration meter, and a sampling probe for measurement of total mass concentration of smoke particles. Located upstream of the fire origin and also along the wall of the gallery at approximately 14 m and 5 m upstream were two video cameras capable of both smoke and flame detection. During the experiments, alarm times of the smoke detectors and video cameras were measured while the smoke obscuration and total smoke mass were continually measured. Twelve large-scale experiments were conducted using three different types of fire-resistant conveyor belts and four air velocities for each belt. The air velocities spanned the range from 1.0 m/s to 6.9 m/s. The results of these experiments are compared to previous large-scale results obtained using a smaller fire gallery and much narrower (1.07-m) conveyor belts to determine if the fire detection criteria previously developed (1) remained valid for the wider conveyor belts. Although some differences between these and the previous experiments did occur, the results, in general, compare very favorably. Differences are duly noted and their impact on fire

Reconstructing the size distribution of the primordial Main Belt

Science.gov (United States)

Tsirvoulis, G.; Morbidelli, A.; Delbo, M.; Tsiganis, K.

2018-04-01

In this work we aim to constrain the slope of the size distribution of main-belt asteroids, at their primordial state. To do so we turn out attention to the part of the main asteroid belt between 2.82 and 2.96 AU, the so-called "pristine zone", which has a low number density of asteroids and few, well separated asteroid families. Exploiting these unique characteristics, and using a modified version of the hierarchical clustering method we are able to remove the majority of asteroid family members from the region. The remaining, background asteroids should be of primordial origin, as the strong 5/2 and 7/3 mean-motion resonances with Jupiter inhibit transfer of asteroids to and from the neighboring regions. The size-frequency distribution of asteroids in the size range 17 size distribution slope q = - 1.43 . In addition, applying the same 'family extraction' method to the neighboring regions, i.e. the middle and outer belts, and comparing the size distributions of the respective background populations, we find statistical evidence that no large asteroid families of primordial origin had formed in the middle or pristine zones.

The JET belt limiter tiles

International Nuclear Information System (INIS)

Deksnis, E.

1988-09-01

The belt limiter system, comprising two full toroidal rings of limiter tiles, was installed in JET in 1987. In consists of water-cooled fins with the limiter material in form of tile inbetween. The tiles are designed to absorb heat fluxes during irradiation without the surface temperature exceeding 2000 0 C and to radiate this heat between pulses to the water cooled sink whose temperature is lower than that of the vacuum vessel. An important feature of the design is to maximise the area of the radiating surface facing the water cooled fin. This leads to a tile depth much greater than the width of the tile facing the heat flux. Limiter tiles intercept particles flowing out of the plasma through the area between the two belt limiter rings and through remaining surface area of the plasma column. Power deposition to a limiter tile depends strongly on the shape of the plasma, the edge plasma properties as well as on the surface profile of the tiles. This paper will discuss the methodology that was followed in producing an optimized surface profile of the tiles. This shaped profile has the feature that the resulting power deposition profile is roughly similar for a wide range of plasma parameters. (author)

Origin of the asteroid belt

International Nuclear Information System (INIS)

Wetherill, G.W.

1989-01-01

Earlier work and concepts relevant to the origin of the asteroid belt are reviewed and considered in the context of the more general question of solar system origin. Several aspects of asteroidal origin by accumulation of smaller bodies have been addressed by new dynamic studies. Numerical and analytical solutions of the dynamical theory of planetesimal accumulation are characterized by a bifurcation into runaway and nonrunaway solutions. The differences in time scales resulting from runaway and nonrunaway growth can be more important than conventional time scale differences determined by heliocentric distances. This introduces new possibilities, e.g., planetary accumulation may be more rapid at the distance of Jupiter than in the asteroid belt, thus permitting Jupiter to control asteroidal growth. Although alternatives must be seriously considered, the most promising approach to asteroidal origin is one in which the initial surface density of the solar nebula varied smoothly between the terrestrial and giant-planet region. In the absence of external perturbations, it is found that runaway growth of excessively large asteroids would then occur on <1 Myr, but fairly modest external perturbations by Jupiter, Saturn or other perturbers, resulting in eccentricities ∼0.01 may quench runaways, truncate asteroidal growth at their present size, and then initiate the necessary loss of asteroidal material by mutual fragmentation

Granitoids of South Korea and Southwest Japan. Trace element evidence regarding their differentiation

International Nuclear Information System (INIS)

Tsusue, Akio; Mizuta, Toshio; Tamai, Tadaharu.

1994-01-01

Although we have already published our trace element data for granitoids of South Korea and Southwest Japan, and we have interpreted REE patterns and Ba, Rb and Sr relationships of the granitoids (Tsusue et al., 1986, 1987a, 1987b, 1988), we intend to review briefly the trace element data of South Korea and Southwest Japan in this report. (J.P.N.)

Attitudes towards child restrains and seat belts usage in the learned population of Karachi, Pakistan.

Science.gov (United States)

Siddiqui, Emaduddin; Ejaz, Kiran; Waheed, Shahan; Kazi, Ghazala Irfan; Khursheed, Munawar

2014-01-01

Motor vehicles crashes (MVCs) are the leading cause of injury related morbidity and mortality in developed countries. Recent evidence proves that properly used child seat belts can dramatically reduce the risk of severe and life-threatening injury from MVCs. There are rarities of thought and inspiration regarding the use of child seat belts in our society and region, therefore we lack of data regarding factors and paucity of usage of child seat belts in motor vehicles. This study aimed to assess the knowledge and attitudes of child seat belt usage among the educated population in Karachi, Pakistan. Altogether 304 employees were investigated. They were employees of Aga Khan University who were using their cars and having children younger than 10 years old. A cross sectional observational study was designed, and a 36-item questionnaire in English was used to collect data on participants' demographic details, designation, educational level, economic status, validity of driving license, number of children and cars, availability of adult seat belts and child seat belts along with their functionality, awareness, knowledge and attitude toward its use, and reason of not using these devices. SPSS version 20 for Windows was used to analyze the data and the Chi-square test was used. Totally 290 participants were recruited with a response rate of 72% (212). Of 212 participants, 126 (59%) were male. 154 (72.6%) participants had valid driver licenses, and 154 (72.6%) had adult seat belts in their vehicles. Only 32 (15%) reported regular use of adult seat belts. Although 168 (79.2%) participants had some knowledge about child restrains (CRs), only 65 (22%) had CRs in their cars. Eighty-two (38.7%) participants got the knowledge about CRs and seat belts from media. Mothers were more concerned about the use of CRs than fathers. Only 14 (6.6%) parents were found to use both adult and child seat belts all the time. Of the 157 parents who did not us use CRs, 42 considered unnecessary

The Hawaii trails project: comet-hunting in the main asteroid belt

Science.gov (United States)

Hsieh, H. H.

2009-10-01

Context: The mysterious solar system object 133P/(7968) Elst-Pizarro is dynamically asteroidal, yet displays recurrent comet-like dust emission. Two scenarios were hypothesized to explain this unusual behavior: 1) 133P is a classical comet from the outer solar system that has evolved onto a main-belt orbit or 2) 133P is a dynamically ordinary main-belt asteroid on which subsurface ice has recently been exposed. If 1) is correct, the expected rarity of a dynamical transition onto an asteroidal orbit implies that 133P could be alone in the main belt. In contrast, if 2) is correct, other icy main-belt objects should exist and could also exhibit cometary activity. Aims: Believing 133P to be a dynamically ordinary, yet icy main-belt asteroid, I set out to test the primary prediction of the hypothesis: that 133P-like objects should be common and could be found by an appropriately designed observational survey. Methods: I conducted just such a survey - the Hawaii Trails Project - of selected main-belt asteroids in a search for objects displaying cometary activity. Optical observations were made of targets selected from among the Themis, Koronis, and Veritas asteroid families, the Karin asteroid cluster, and low-inclination, kilometer-scale outer-belt asteroids, using the Lulin 1.0 m, small and moderate aperture research telescope system (SMARTS) 1.0 m, University of Hawaii 2.2 m, southern astrophysical research (SOAR) 4.1 m, Gemini North 8.1 m, Subaru 8.2 m, and Keck I 10 m telescopes. Results: I made 657 observations of 599 asteroids, discovering one active object now known as 176P/LINEAR, leading to the identification of the new cometary class of main-belt comets (MBCs). These results suggest that there could be ~100 currently active MBCs among low-inclination, kilometer-scale outer-belt asteroids. Physically and statistically, MBC activity is consistent with initiation by meter-sized impactors. The estimated rate of impacts and sizes of resulting active sites, however

COMPREHENSIVE CHECK MEASUREMENT OF KEY PARAMETERS ON MODEL BELT CONVEYOR

Directory of Open Access Journals (Sweden)

Vlastimil MONI

2013-07-01

Full Text Available Complex measurements of characteristic parameters realised on a long distance model belt conveyor are described. The main objective was to complete and combine the regular measurements of electric power on drives of belt conveyors operated in Czech opencast mines with measurements of other physical quantities and to gain by this way an image of their mutual relations and relations of quantities derived from them. The paper includes a short description and results of the measurements on an experimental model conveyor with a closed material transport way.

Measurement and monitoring of electrocardiogram belt tension in premature infants for assessment of respiratory function

OpenAIRE

Hegyi Thomas; Hiatt Mark; Ciaccio Edward J; Drzewiecki Gary M

2007-01-01

Abstract Background Monitoring of the electrocardiogram (ECG) in premature infants with conventional adhesive-backed electrodes can harm their sensitive skin. Use of an electrode belt prevents skin irritation, but the effect of belt pressure on respiratory function is unknown. A strain gauge sensor is described which measures applied belt tension. Method The device frame was comprised of an aluminum housing and slide to minimize the device weight. Velcro tabs connected housing and slide to op...

Converter-controlled belt conveyor systems under the difficult conditions; Umrichtergesteuerte Bandanlagen unter schwierigen Bedingungen

Energy Technology Data Exchange (ETDEWEB)

Horz, Michael-Josef [RAG Deutsche Steinkohle, Herne (Germany). Abt. Elektrotechnik unter Tage; Mueller, Uwe [RAG Deutsche Steinkohle, Herne (Germany). Servicebereich Technik- und Logistikdienste

2010-05-15

Panel 572 is located at a depth of 1,200 m in the Girondelle seam at the West mine. The panel has a mean thickness of 2.5 m and is designed as a shearer loader face with a length of 460 m. Coal is conveyed to the shaft by six belts with a total length of about 6 km and a total lifting height of 396 m. The main conveyor belt 1 with an installed power of 3 MW links the panel to a bunker. Conveyor belts 2 to 4 each with 500 kW drive power have operated in a stable manner since the start of working of the panel. Due to in-seam drivage with a selective-cut machine of type AM 85 an area with a marked trough was produced in the coal conveyor road. This area is traversed by belt 5. The planning and control of the conveyor belt in this difficult geological environment impose high demands on drive and control technology. To ensure stable operation under different loads a raft of measures was resolved and implemented. The contribution examines the problem and describes the implemented measures in detail. (orig.)

Disparities in safety belt use by sexual orientation identity among US high school students.

Science.gov (United States)

Reisner, Sari L; Van Wagenen, Aimee; Gordon, Allegra; Calzo, Jerel P

2014-02-01

We examined associations between adolescents' safety belt use and sexual orientation identity. We pooled data from the 2005 and 2007 Youth Risk Behavior Surveys (n = 26,468 weighted; mean age = 15.9 years; 35.4% White, 24.7% Black, 23.5% Latino, 16.4% other). We compared lesbian and gay (1.2%), bisexual (3.5%), and unsure (2.6%) youths with heterosexuals (92.7%) on a binary indicator of passenger safety belt use. We stratified weighted multivariable logistic regression models by sex and adjusted for survey wave and sampling design. Overall, 12.6% of high school students reported "rarely" or "never" wearing safety belts. Sexual minority youths had increased odds of reporting nonuse relative to heterosexuals (48% higher for male bisexuals, 85% for lesbians, 46% for female bisexuals, and 51% for female unsure youths; P < .05), after adjustment for demographic (age, race/ethnicity), individual (body mass index, depression, bullying, binge drinking, riding with a drunk driver, academic achievement), and contextual (living in jurisdictions with secondary or primary safety belt laws, percentage below poverty, percentage same-sex households) risk factors. Public health interventions should address sexual orientation identity disparities in safety belt use.

A cost benefit analysis of an enhanced seat belt enforcement program in South Africa.

Science.gov (United States)

Harris, G T; Olukoga, I A

2005-04-01

To examine whether a program to increase the wearing of seat belts in a South African urban area would be worthwhile in societal terms. A cost benefit analysis of a one year enhanced seat belt enforcement program in eThekwini (Durban) Municipality. Data were drawn from two main sources--a 1998 study of the cost of road crashes in South Africa and, given the absence of other data, a meta-analysis of the effectiveness of various types of interventions to reduce road crash casualties in the United States--and were analyzed using cost benefit analysis. A program designed to enforce greater wearing of seat belts, estimated to cost 2 million rand in one year, could be reasonably expected to increase seat belt usage rates by 16 percentage points and reduce fatalities and injuries by 9.5%. This would result in saved social costs of 13.6 million rand in the following year or a net present value of 11.6 million rand. There would also be favorable consequences for municipal finances. Investment in a program to increase seat belt wearing rates is highly profitable in societal terms.

Discriminating the biophysical impacts of coastal upwelling and mud banks along the southwest coast of India

Digital Repository Service at National Institute of Oceanography (India)

Karnan, C.; Jyothibabu, R.; Arunpandi, N.; Jagadeesan, L.; Muraleedharan, K.R.; Pratihary, A.K.; Balachandran, K.K.; Naqvi, S.W.A.

Coastal upwelling and mud banks are two oceanographic processes concurrently operating along certain stretches of the southwest (Kerala) coast of India during the Southwest Monsoon period (June-September), facilitating significant enhancement...

Radiation Belt Transport Driven by Solar Wind Dynamic Pressure Fluctuations

Science.gov (United States)

Kress, B. T.; Hudson, M. K.; Ukhorskiy, A. Y.; Mueller, H.

2012-12-01

The creation of the Earth's outer zone radiation belts is attributed to earthward transport and adiabatic acceleration of electrons by drift-resonant interactions with electromagnetic fluctuations in the magnetosphere. Three types of radial transport driven by solar wind dynamic pressure fluctuations that have been identified are: (1) radial diffusion [Falthammer, 1965], (2) significant changes in the phase space density radial profile due to a single or few ULF drift-resonant interactions [Ukhorskiy et al., 2006; Degeling et al., 2008], and (3) shock associated injections of radiation belt electrons occurring in less than a drift period [Li et al., 1993]. A progress report will be given on work to fully characterize different forms of radial transport and their effect on the Earth's radiation belts. The work is being carried out by computing test-particle trajectories in electric and magnetic fields from a simple analytic ULF field model and from global MHD simulations of the magnetosphere. Degeling, A. W., L. G. Ozeke, R. Rankin, I. R. Mann, and K. Kabin (2008), Drift resonant generation of peaked relativistic electron distributions by Pc 5 ULF waves, textit{J. Geophys. Res., 113}, A02208, doi:10.1029/2007JA012411. Fälthammar, C.-G. (1965), Effects of Time-Dependent Electric Fields on Geomagnetically Trapped Radiation, J. Geophys. Res., 70(11), 2503-2516, doi:10.1029/JZ070i011p02503. Li, X., I. Roth, M. Temerin, J. R. Wygant, M. K. Hudson, and J. B. Blake (1993), Simulation of the prompt energization and transport of radiation belt particles during the March 24, 1991 SSC, textit{Geophys. Res. Lett., 20}(22), 2423-2426, doi:10.1029/93GL02701. Ukhorskiy, A. Y., B. J. Anderson, K. Takahashi, and N. A. Tsyganenko (2006), Impact of ULF oscillations in solar wind dynamic pressure on the outer radiation belt electrons, textit{Geophys. Res. Lett., 33}(6), L06111, doi:10.1029/2005GL024380.

Design aspects of multiple driven belt conveyors

NARCIS (Netherlands)

Nuttall, A.J.G.

2007-01-01

Worldwide belt conveyors are used to transport a great variety of bulk solid materials. The desire to carry higher tonnages over longer distances and more diverse routes, while keeping exploitation costs as low as possible, has fuelled many technological advances. An interesting development in the

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives

OpenAIRE

Chaitiemwong, N.; Hazeleger, W.C.; Beumer, R.R.

2010-01-01

Survival of Listeria monocytogenes on a conveyor belt material with or without antimicrobial additives, in the absence or presence of food debris from meat, fish and vegetables and at temperatures of 10, 25 and 37 °C was investigated. The pathogen survived best at 10 °C, and better at 25 °C than at 37 °C on both conveyor belt materials. The reduction in the numbers of the pathogen on belt material with antimicrobial additives in the first 6 h at 10 °C was 0.6 log unit, which was significantly...

U.S. Border Patrol Fiscal Year Statistics Southwest border sector deaths - FY 1998 through FY 2013

Data.gov (United States)

Department of Homeland Security — Southwest Border Sectors include: Del Rio, El Centro, El Paso, Laredo, Rio Grande Valley, San Diego, Tucson, Yuma Southwest Border Deaths By Fiscal Year (Oct. 1st...

Two Belts, One Road? - The role of Africa in Chinas's Belt & Road initiative

OpenAIRE

Breuer, Julia

2017-01-01

In the light of the EU-Africa Summit 2017 and of the G20 Summit 2017 with Africa being one of the focus areas, China’s engagement in Africa seems more relevant than ever. China’s “One Belt, One Road” initiative (OBOR) or silk road initiative is often referred to as a Eurasian infrastructure network initiative, but it is in fact much more than that. The maritime silk road is supposed to go past the coast of East Africa, where several ports are being built and will be built. Furthermore, ports ...

Nonlinear Whistler Wave Physics in the Radiation Belts

Science.gov (United States)

Crabtree, Chris

2016-10-01

Wave particle interactions between electrons and whistler waves are a dominant mechanism for controlling the dynamics of energetic electrons in the radiation belts. They are responsible for loss, via pitch-angle scattering of electrons into the loss cone, and energization to millions of electron volts. It has previously been theorized that large amplitude waves on the whistler branch may scatter their wave-vector nonlinearly via nonlinear Landau damping leading to important consequences for the global distribution of whistler wave energy density and hence the energetic electrons. It can dramatically reduce the lifetime of energetic electrons in the radiation belts by increasing the pitch angle scattering rate. The fundamental building block of this theory has now been confirmed through laboratory experiments. Here we report on in situ observations of wave electro-magnetic fields from the EMFISIS instrument on board NASA's Van Allen Probes that show the signatures of nonlinear scattering of whistler waves in the inner radiation belts. In the outer radiation belts, whistler mode chorus is believed to be responsible for the energization of electrons from 10s of Kev to MeV energies. Chorus is characterized by bursty large amplitude whistler mode waves with frequencies that change as a function of time on timescales corresponding to their growth. Theories explaining the chirping have been developed for decades based on electron trapping dynamics in a coherent wave. New high time resolution wave data from the Van Allen probes and advanced spectral techniques are revealing that the wave dynamics is highly structured, with sub-elements consisting of multiple chirping waves with discrete frequency hops between sub-elements. Laboratory experiments with energetic electron beams are currently reproducing the complex frequency vs time dynamics of whistler waves and in addition revealing signatures of wave-wave and beat-wave nonlinear wave-particle interactions. These new data

Distinct motor strategies underlying split-belt adaptation in human walking and running.

Science.gov (United States)

Ogawa, Tetsuya; Kawashima, Noritaka; Obata, Hiroki; Kanosue, Kazuyuki; Nakazawa, Kimitaka

2015-01-01

The aim of the present study was to elucidate the adaptive and de-adaptive nature of human running on a split-belt treadmill. The degree of adaptation and de-adaptation was compared with those in walking by calculating the antero-posterior component of the ground reaction force (GRF). Adaptation to walking and running on a split-belt resulted in a prominent asymmetry in the movement pattern upon return to the normal belt condition, while the two components of the GRF showed different behaviors depending on the gaits. The anterior braking component showed prominent adaptive and de-adaptive behaviors in both gaits. The posterior propulsive component, on the other hand, exhibited such behavior only in running, while that in walking showed only short-term aftereffect (lasting less than 10 seconds) accompanied by largely reactive responses. These results demonstrate a possible difference in motor strategies (that is, the use of reactive feedback and adaptive feedforward control) by the central nervous system (CNS) for split-belt locomotor adaptation between walking and running. The present results provide basic knowledge on neural control of human walking and running as well as possible strategies for gait training in athletic and rehabilitation scenes.

Distinct motor strategies underlying split-belt adaptation in human walking and running.

Directory of Open Access Journals (Sweden)

Tetsuya Ogawa

Full Text Available The aim of the present study was to elucidate the adaptive and de-adaptive nature of human running on a split-belt treadmill. The degree of adaptation and de-adaptation was compared with those in walking by calculating the antero-posterior component of the ground reaction force (GRF. Adaptation to walking and running on a split-belt resulted in a prominent asymmetry in the movement pattern upon return to the normal belt condition, while the two components of the GRF showed different behaviors depending on the gaits. The anterior braking component showed prominent adaptive and de-adaptive behaviors in both gaits. The posterior propulsive component, on the other hand, exhibited such behavior only in running, while that in walking showed only short-term aftereffect (lasting less than 10 seconds accompanied by largely reactive responses. These results demonstrate a possible difference in motor strategies (that is, the use of reactive feedback and adaptive feedforward control by the central nervous system (CNS for split-belt locomotor adaptation between walking and running. The present results provide basic knowledge on neural control of human walking and running as well as possible strategies for gait training in athletic and rehabilitation scenes.

Algoma-type Neoproterozoic BIFs and related marbles in the Seridó Belt (NE Brazil)

DEFF Research Database (Denmark)

Sial, Alcides N.; Campos, Marcel S.; Gaucher, Claudio

2015-01-01

The Jucurutu Formation in the Seridó Belt, northeastern Brazil, encompasses fine-to coarse-grained amphibolite-facies marbles, locally with cross-bedding and stromatolites. Banded iron formations (BIF) at three localities in this belt comprise itabirites (actinolite- or cummingtonite-itabirite an...

Rapid flattening of butterfly pitch angle distributions of radiation belt electrons by whistler-mode chorus

Science.gov (United States)

Yang, Chang; Su, Zhenpeng; Xiao, Fuliang; Zheng, Huinan; Wang, Yuming; Wang, Shui; Spence, H. E.; Reeves, G. D.; Baker, D. N.; Blake, J. B.; Funsten, H. O.

2016-08-01

Van Allen radiation belt electrons exhibit complex dynamics during geomagnetically active periods. Investigation of electron pitch angle distributions (PADs) can provide important information on the dominant physical mechanisms controlling radiation belt behaviors. Here we report a storm time radiation belt event where energetic electron PADs changed from butterfly distributions to normal or flattop distributions within several hours. Van Allen Probes observations showed that the flattening of butterfly PADs was closely related to the occurrence of whistler-mode chorus waves. Two-dimensional quasi-linear STEERB simulations demonstrate that the observed chorus can resonantly accelerate the near-equatorially trapped electrons and rapidly flatten the corresponding electron butterfly PADs. These results provide a new insight on how chorus waves affect the dynamic evolution of radiation belt electrons.

Rapid flattening of butterfly pitch angle distributions of radiation belt electrons by whistler-mode chorus

International Nuclear Information System (INIS)

Yang, Chang; Changsha University of Science and Technology, Changsha; Su, Zhenpeng; Xiao, Fuliang; Zheng, Huinan

2016-01-01

Van Allen radiation belt electrons exhibit complex dynamics during geomagnetically active periods. Investigation of electron pitch angle distributions (PADs) can provide important information on the dominant physical mechanisms controlling radiation belt behaviors. In this paper, we report a storm time radiation belt event where energetic electron PADs changed from butterfly distributions to normal or flattop distributions within several hours. Van Allen Probes observations showed that the flattening of butterfly PADs was closely related to the occurrence of whistler-mode chorus waves. Two-dimensional quasi-linear STEERB simulations demonstrate that the observed chorus can resonantly accelerate the near-equatorially trapped electrons and rapidly flatten the corresponding electron butterfly PADs. Finally, these results provide a new insight on how chorus waves affect the dynamic evolution of radiation belt electrons.

Ice Caps and Ice Belts: The Effects of Obliquity on Ice−Albedo Feedback

Energy Technology Data Exchange (ETDEWEB)

Rose, Brian E. J. [Department of Atmospheric and Environmental Sciences, University at Albany (State University of New York), 1400 Washington Avenue, Albany, NY 12222 (United States); Cronin, Timothy W. [Program in Atmospheres, Oceans, and Climate, Massachusetts Institute of Technology 77 Massachusetts Avenue, Cambridge, MA 02139 (United States); Bitz, Cecilia M., E-mail: brose@albany.edu [Department of Atmospheric Sciences, MS 351640, University of Washington, Seattle, WA 98195-1640 (United States)

2017-09-01

Planetary obliquity determines the meridional distribution of the annual mean insolation. For obliquity exceeding 55°, the weakest insolation occurs at the equator. Stable partial snow and ice cover on such a planet would be in the form of a belt about the equator rather than polar caps. An analytical model of planetary climate is used to investigate the stability of ice caps and ice belts over the widest possible range of parameters. The model is a non-dimensional diffusive Energy Balance Model, representing insolation, heat transport, and ice−albedo feedback on a spherical planet. A complete analytical solution for any obliquity is given and validated against numerical solutions of a seasonal model in the “deep-water” regime of weak seasonal ice line migration. Multiple equilibria and unstable transitions between climate states (ice-free, Snowball, or ice cap/belt) are found over wide swaths of parameter space, including a “Large Ice-Belt Instability” and “Small Ice-Belt Instability” at high obliquity. The Snowball catastrophe is avoided at weak radiative forcing in two different scenarios: weak albedo feedback and inefficient heat transport (favoring stable partial ice cover), or efficient transport at high obliquity (favoring ice-free conditions). From speculative assumptions about distributions of planetary parameters, three-fourths to four-fifths of all planets with stable partial ice cover should be in the form of Earth-like polar caps.

A Seroepidemiological Study of Serogroup A Meningococcal Infection in the African Meningitis Belt.

Directory of Open Access Journals (Sweden)

Olivier Manigart

Full Text Available The pattern of epidemic meningococcal disease in the African meningitis belt may be influenced by the background level of population immunity but this has been measured infrequently. A standardised enzyme-linked immunosorbent assay (ELISA for measuring meningococcal serogroup A IgG antibodies was established at five centres within the meningitis belt. Antibody concentrations were then measured in 3930 individuals stratified by age and residence from six countries. Seroprevalence by age was used in a catalytic model to determine the force of infection. Meningococcal serogroup A IgG antibody concentrations were high in each country but showed heterogeneity across the meningitis belt. The geometric mean concentration (GMC was highest in Ghana (9.09 μg/mL [95% CI 8.29, 9.97] and lowest in Ethiopia (1.43 μg/mL [95% CI 1.31, 1.57] on the margins of the belt. The force of infection was lowest in Ethiopia (λ = 0.028. Variables associated with a concentration above the putative protective level of 2 μg/mL were age, urban residence and a history of recent vaccination with a meningococcal vaccine. Prior to vaccination with the serogroup A meningococcal conjugate vaccine, meningococcal serogroup A IgG antibody concentrations were high across the African meningitis belt and yet the region remained susceptible to epidemics.

Kinematic evolution of fold and thrust belts. Insights from experimental modeling

International Nuclear Information System (INIS)

Ueta, Keiichi

2011-01-01

Physical experiments were performed to gain a better understanding on the kinematic evolution of fold and thrust belts. The present study focuses on deformation of sedimentary cover caused by thrust and reverse movements along the basement fault. Our physical models comprise dry quartz sand representing brittle sedimentary rock and viscous silicone polymer representing overpressured mudstone. Computerized X-ray tomography was applied to the experiments to analyze the kinematic evolution of fold and thrust belts. In the sand models, the width of deformation zone above thrust was wider than that above reverse fault, because back thrust developed on the hanging wall of reverse fault. Within the physical models composed of dry sand and silicone polymer, minor folds and thrusts with minor displacement developed on the footwall of the major monoclinal flexure. These results compare well with the geometry and kinematic evolution of the fold and thrust belts in Japan. (author)

The Security Challenges of the “One Belt, One Road” Initiative and China’s Choices

OpenAIRE

Haiquan, Liu

2017-01-01

The Silk Road Economic Belt and the 21st Century Maritime Silk Road initiatives (“One Belt, One Road”) are of significance in enhancing China’s open economy. This article explores the dual security challenges faced by the “One Belt, One Road” initiative. These challenges include both traditional security challenges, such as great power competition, territorial and island disputes, and political turmoil in the region, as well as non-traditional threats such as terrorism, piracy, and transnatio...

Southwest University's Innovative No-Fee Teacher Education Internships

Science.gov (United States)

Zhang, Huirong; Xiong, Jianjie; Song, Naiqing

2013-01-01

This article describes Southwest University's no-fee teacher education internship models in terms of their organization, content, requirements, and quality assurance. It further introduces the quality assurance system, which comprises building a teaching internship system, establishing internship sites, guiding teacher training, and processing…

Technological choice and change in the Southwest Bath in the Athenian Agora

Directory of Open Access Journals (Sweden)

Artz, James

2012-04-01

Full Text Available During its five architectural phases, the Southwest bath in the Athenian Agora changes from a Greek-style bath into a Roman-style bath. This article will focus on the first two phases, when Roman elements begin to be incorporated into the traditional forms of Greek bath architecture – particularly, a hypocaust floor system and a concrete vaulted ceiling built into a traditional Greek tholos bath. After describing these architectural features and analyzing the techniques used in their construction, I will examine possible sources of influence on the design and construction of the Southwest baths. The Roman army, citizenry, and workmen could all have potentially affected the incorporation of Roman bathing technologies and building techniques into the Southwest bath. The available evidence, however, indicates that the most likely source of influence is Roman workmen, who were employed in large numbers for the numerous building projects underway in Augustan Athens.

A new on-belt elemental analyzer for the cement industry

International Nuclear Information System (INIS)

Sowerby, B.D.; Lim, C.S.; Tickner, J.R.; Manias, C.; Retallack, D.

2001-01-01

On-line control of raw mill feed composition is a key to the improved control of cement plants. Elements of primary importance to the industry are calcium, silicon, aluminum and iron. Direct on-conveyor belt analysis of raw mill feed is required, independent of changes in belt loading, moisture content, and both horizontal and vertical segregation. A new and improved on-conveyor belt elemental analyzer for cement raw mill feed has been developed and tested successfully in Adelaide Brighton's Birkenhead cement plant. The analyzer utilizes two 241 Am-Be neutron sources and multiple BGO detectors to measure both neutron inelastic scatter and thermal neutron capture gamma rays. Dynamic tests in the plant on highly segregated material having depths in the range 100 to 200 mm have shown analyzer total RMS errors of 0.49, 0.52, 0.38 and 0.23 wt.% (on a loss free basis) for CaO, SiO 2 , Al 2 O 3 , and Fe 2 O 3 respectively, when 10-minute counting periods are used

Modeling Belt-Servomechanism by Chebyshev Functional Recurrent Neuro-Fuzzy Network

Science.gov (United States)

Huang, Yuan-Ruey; Kang, Yuan; Chu, Ming-Hui; Chang, Yeon-Pun

A novel Chebyshev functional recurrent neuro-fuzzy (CFRNF) network is developed from a combination of the Takagi-Sugeno-Kang (TSK) fuzzy model and the Chebyshev recurrent neural network (CRNN). The CFRNF network can emulate the nonlinear dynamics of a servomechanism system. The system nonlinearity is addressed by enhancing the input dimensions of the consequent parts in the fuzzy rules due to functional expansion of a Chebyshev polynomial. The back propagation algorithm is used to adjust the parameters of the antecedent membership functions as well as those of consequent functions. To verify the performance of the proposed CFRNF, the experiment of the belt servomechanism is presented in this paper. Both of identification methods of adaptive neural fuzzy inference system (ANFIS) and recurrent neural network (RNN) are also studied for modeling of the belt servomechanism. The analysis and comparison results indicate that CFRNF makes identification of complex nonlinear dynamic systems easier. It is verified that the accuracy and convergence of the CFRNF are superior to those of ANFIS and RNN by the identification results of a belt servomechanism.

Belt Buckles-Increasing Awareness of Nickel Exposure in Children: A Case Report.

Science.gov (United States)

Goldenberg, Alina; Admani, Shehla; Pelletier, Janice L; Jacob, Sharon E

2015-09-01

Children, especially those with atopic dermatitis, are at risk for nickel sensitization and subsequent dermatitis from metal-containing objects, namely belt buckles. We describe allergic contact dermatitis in 12 children with peri-umbilical nickel dermatitis (with and without generalized involvement) caused by dimethylglyoxime-positive belt buckles. The patients' symptoms resolved with avoidance of the nickel-containing products. Copyright © 2015 by the American Academy of Pediatrics.

Impact of Selected Parameters on the Fatigue Strength of Splices on Multiply Textile Conveyor Belts

Science.gov (United States)

Bajda, Mirosław; Błażej, Ryszard; Hardygóra, Monika

2016-10-01

Splices are the weakest points in the conveyor belt loop. The strength of these joints, and thus their design as well as the method and quality of splicing, determine the strength of the whole conveyor belt loop. A special zone in a splice exists, where the stresses in the adjacent plies or cables differ considerably from each other. This results in differences in the elongation of these elements and in additional shearing stresses in the rubber layer. The strength of the joints depends on several factors, among others on the parameters of the joined belt, on the connecting layer and the technology of joining, as well as on the materials used to make the joint. The strength of the joint constitutes a criterion for the selection of a belt suitable for the operating conditions, and therefore methods of testing such joints are of great importance. This paper presents the method of testing fatigue strength of splices made on multi-ply textile conveyor belts and the results of these studies.

Detachments in Shale: Controlling Characteristics on Fold-Thrust Belt Style

Science.gov (United States)

Hansberry, Rowan; King, Ros; Collins, Alan; Morley, Chris

2013-04-01

Fold-thrust belts occur across multiple tectonic settings where thin-skinned deformation is accommodated by one or more detachment zones, both basal and within the fold-thrust belt. These fold-thrust belts exhibit considerable variation in structural style and vergence depending on the characteristics (e.g. strength, thickness, and lithology) and number of detachment zones. Shale as a detachment lithology is intrinsically weaker than more competent silts and sands; however, it can be further weakened by high pore pressures, reducing resistance to sliding and; high temperatures, altering the rheology of the detachment. Despite the implications for petroleum exploration and natural hazard assessment the precise nature by which detachments in shale control and are involved in deformation in fold-thrust belts is poorly understood. Present-day active basal detachment zones are usually located in inaccessible submarine regions. Therefore, this project employs field observations and sample analysis of ancient, exhumed analogues to document the nature of shale detachments (e.g. thickness, lithology, dip and dip direction, deformational temperature and thrust propagation rates) at field sites in Thailand, Norway and New Zealand. X-ray diffraction analysis of illite crystallinity and oxygen stable isotopes analysis are used as a proxy for deformational temperature whilst electron-backscatter diffraction analysis is used to constrain microstructural deformational patterns. K-Ar dating of synkinematic clay fault gouges is being applied to date the final stages of activity on individual faults with a view to constraining thrust activation sequences. It is not possible to directly measure palaeo-data for some key detachment parameters, such as pore pressure and coefficients of friction. However, the use of critical taper wedge theory has been used to successfully infer internal and basal coefficients of friction and depth-normalized pore pressure within a wedge and at its base

Upscaling Ameriflux observations to assess drought impacts on gross primary productivity across the Southwest

Science.gov (United States)

Barnes, M.; Moore, D. J.; Scott, R. L.; MacBean, N.; Ponce-Campos, G. E.; Breshears, D. D.

2017-12-01

Both satellite observations and eddy covariance estimates provide crucial information about the Earth's carbon, water and energy cycles. Continuous measurements from flux towers facilitate exploration of the exchange of carbon dioxide, water and energy between the land surface and the atmosphere at fine temporal and spatial scales, while satellite observations can fill in the large spatial gaps of in-situ measurements and provide long-term temporal continuity. The Southwest (Southwest United States and Northwest Mexico) and other semi-arid regions represent a key uncertainty in interannual variability in carbon uptake. Comparisons of existing global upscaled gross primary production (GPP) products with flux tower data at sites across the Southwest show widespread mischaracterization of seasonality in vegetation carbon uptake, resulting in large (up to 200%) errors in annual carbon uptake estimates. Here, remotely sensed and distributed meteorological inputs are used to upscale GPP estimates from 25 Ameriflux towers across the Southwest to the regional scale using a machine learning approach. Our random forest model incorporates two novel features that improve the spatial and temporal variability in GPP. First, we incorporate a multi-scalar drought index at multiple timescales to account for differential seasonality between ecosystem types. Second, our machine learning algorithm was trained on twenty five ecologically diverse sites to optimize both the monthly variability in and the seasonal cycle of GPP. The product and its components will be used to examine drought impacts on terrestrial carbon cycling across the Southwest including the effects of drought seasonality and on carbon uptake. Our spatially and temporally continuous upscaled GPP product drawing from both ground and satellite data over the Southwest region helps us understand linkages between the carbon and water cycles in semi-arid ecosystems and informs predictions of vegetation response to future

Impact of Implementing a Primary Enforcement Seat Belt Law in Florida : A Case Study

Science.gov (United States)

2012-08-01

On June 30, 2009, Florida implemented a primary seat belt law. The State was already engaged in a Rural : Demonstration Program (RDP) to increase belt usage in rural areas in the northern part of the State and participated : regularly in annual Click...

Demonstration of the Trauma Nurses Talk Tough seat belt diversion program in North Carolina.

Science.gov (United States)

2014-03-01

Trauma Nurses Talk Tough is a seat belt diversion program originally developed at the Legacy Emanuel Hospital in Portland, Oregon, in 1988. Attendance at the course is a condition for a one-time dismissal of a seat belt citation without fine or court...

Coordinates for Representing Radiation Belt Particle Flux

Science.gov (United States)

Roederer, Juan G.; Lejosne, Solène

2018-02-01

Fifty years have passed since the parameter "L-star" was introduced in geomagnetically trapped particle dynamics. It is thus timely to review the use of adiabatic theory in present-day studies of the radiation belts, with the intention of helping to prevent common misinterpretations and the frequent confusion between concepts like "distance to the equatorial point of a field line," McIlwain's L-value, and the trapped particle's adiabatic L* parameter. And too often do we miss in the recent literature a proper discussion of the extent to which some observed time and space signatures of particle flux could simply be due to changes in magnetospheric field, especially insofar as off-equatorial particles are concerned. We present a brief review on the history of radiation belt parameterization, some "recipes" on how to compute adiabatic parameters, and we illustrate our points with a real event in which magnetospheric disturbance is shown to adiabatically affect the particle fluxes measured onboard the Van Allen Probes.

Accelerated Comparative Fatigue Strength Testing of Belt Adhesive Joints

Science.gov (United States)

Bajda, Miroslaw; Blazej, Ryszard; Jurdziak, Leszek

2017-12-01

Belt joints are the weakest link in the serial structure that creates an endless loop of spliced belt segments. This affects not only the lower strength of adhesive joints of textile belts in comparison to vulcanized splices, but also the replacement of traditional glues to more ecological but with other strength parameters. This is reflected in the lowered durability of adhesive joints, which in underground coal mines is nearly twice shorter than the operating time of belts. Vulcanized splices require high precision in performance, they need long time to achieve cross-linking of the friction mixture and, above all, they require specialized equipment (vulcanization press) which is not readily available and often takes much time to be delivered down, which means reduced mining output or even downtime. All this reduces the reliability and durability of adhesive joints. In addition, due to the consolidation on the Polish coal market, mines are joined into large economic units serviced by a smaller number of processing plants. The consequence is to extend the transport routes downstream and increase reliability requirements. The greater number of conveyors in the chain reduces reliability of supply and increases production losses. With high fixed costs of underground mines, the reduction in mining output is reflected in the increase in unit costs, and this at low coal prices on the market can mean substantial losses for mines. The paper describes the comparative study of fatigue strength of shortened samples of adhesive joints conducted to compare many different variants of joints (various adhesives and materials). Shortened samples were exposed to accelerated fatigue in the usually long-lasting dynamic studies, allowing more variants to be tested at the same time. High correlation between the results obtained for shortened (100 mm) and traditional full-length (3×250 mm) samples renders accelerated tests possible.

76 FR 59682 - Desert Southwest Customer Service Region-Western Area Lower Colorado Balancing Authority-Rate...

Science.gov (United States)

2011-09-27

... DEPARTMENT OF ENERGY Western Area Power Administration Desert Southwest Customer Service Region... CONTACT: Mr. Jack Murray, Rates Manager, Desert Southwest Customer Service Region, Western Area Power... Customer Service Region Network Integration Transmission Service Rate Schedules PD-NTS3 and INT-NTS3 for P...

Belt deviation and its solution of belt weighing feeder machine%皮带称重绐料机皮带跑偏问题殁对策

Institute of Scientific and Technical Information of China (English)

张荣轩

2012-01-01

This article analyzes the reasons of common belt deviation problems during the using of belt weighing feeder machine, and combining practical work experience, proposed its solutions.%本文就皮带称重给料机在使用过程中常见的皮带跑偏问题进行了原因分析，并结合本人多年的工作实践经验，提出其相应的解决办法。

Environmental and psychosocial factors affecting seat belt use among Turkish front-seat occupants in Ankara: two observation studies.

Science.gov (United States)

Simşekoğlu, Ozlem; Lajunen, Timo

2008-01-01

Low seat belt use rate among car occupants is one of the main problems contributing to low driver and passenger safety in Turkey, where injury and fatality rates of car occupants are very high in traffic crashes. The present article consists of two observation studies, which were conducted in Ankara. The first study aimed at investigating environmental factors and occupant characteristics affecting seat belt use among front-seat occupants, and the objective of the second study was to investigate the relationship between driver and front-seat passenger seat belt use. In the first study, 4, 227 front-seat occupants (drivers or front seat passengers) were observed on four different road sides and, in the second study 1, 398 front seat occupants were observed in car parks of five different shopping centers in Ankara. In both observations, front-seat occupants' seat bet use (yes, no), sex (male, female), and age ( 50 years) were recorded. The data were analyzed using chi-square statistics and binary logistic regression techniques. Results of the first study showed that seat belt use proportion among observed front seat occupants was very low (25%). Being female and traveling on intercity roads were two main factors positively related to use a seat belt among front-seat occupants. High correlations between seat belt use of the drivers and front-seat passengers were found in the second study. Overall, low seat belt use rate (25%) among the front-seat occupants should be increased urgently for an improved driver and passenger safety in Turkey. Seat belt campaigns especially tailored for male front-seat occupants and for the front-seat occupants traveling on city roads are needed to increase seat belt use rates among them. Also, both drivers and passengers may have an important role in enforcing seat belt use among themselves.

Pelvic belt effects on pelvic morphometry, muscle activity and body balance in patients with sacroiliac joint dysfunction.

Directory of Open Access Journals (Sweden)

Odette Soisson

Full Text Available The sacroiliac joint (SIJ is frequently involved in low back and pelvic girdle pain. However, morphometrical and functional characteristics related to SIJ pain are poorly defined. Pelvic belts represent one treatment option, but evidence still lacks as to their pain-reducing effects and the mechanisms involved. Addressing these two issues, this case-controlled study compares morphometric, functional and clinical data in SIJ patients and healthy controls and evaluates the effects of short-term pelvic belt application.Morphometric and functional data pertaining to pelvic belt effects were compared in 17 SIJ patients and 17 controls. Lumbar spine and pelvis morphometries were obtained from 3T magnetic resonance imaging. Functional electromyography data of pelvis and leg muscles and center of pressure excursions were measured in one-leg stance. The numerical rating scale was used to evaluate immediate pain-reducing effects.Pelvic morphometry was largely unaltered in SIJ patients and also by pelvic belt application. The angle of lumbar lateral flexion was significantly larger in SIJ patients without belt application. Muscle activity and center of pressure were unaffected by SIJ pain or by belt application in one-leg stance. Nine of 17 patients reported decreased pain intensities under moderate belt application, four reported no change and four reported increased pain intensity. For the entire population investigated here, this qualitative description was not confirmed on a statistical significant level.Minute changes were observed in the alignment of the lumbar spine in the frontal plane in SIJ patients. The potential pain-decreasing effects of pelvic belts could not be attributed to altered muscle activity, pelvic morphometry or body balance in a static short-term application. Long-term belt effects will therefore be of prospective interest.

Pelvic Belt Effects on Pelvic Morphometry, Muscle Activity and Body Balance in Patients with Sacroiliac Joint Dysfunction

Science.gov (United States)

Soisson, Odette; Lube, Juliane; Germano, Andresa; Hammer, Karl-Heinz; Josten, Christoph; Sichting, Freddy; Winkler, Dirk; Milani, Thomas L.; Hammer, Niels

2015-01-01

Introduction The sacroiliac joint (SIJ) is frequently involved in low back and pelvic girdle pain. However, morphometrical and functional characteristics related to SIJ pain are poorly defined. Pelvic belts represent one treatment option, but evidence still lacks as to their pain-reducing effects and the mechanisms involved. Addressing these two issues, this case-controlled study compares morphometric, functional and clinical data in SIJ patients and healthy controls and evaluates the effects of short-term pelvic belt application. Methods Morphometric and functional data pertaining to pelvic belt effects were compared in 17 SIJ patients and 17 controls. Lumbar spine and pelvis morphometries were obtained from 3T magnetic resonance imaging. Functional electromyography data of pelvis and leg muscles and center of pressure excursions were measured in one-leg stance. The numerical rating scale was used to evaluate immediate pain-reducing effects. Results Pelvic morphometry was largely unaltered in SIJ patients and also by pelvic belt application. The angle of lumbar lateral flexion was significantly larger in SIJ patients without belt application. Muscle activity and center of pressure were unaffected by SIJ pain or by belt application in one-leg stance. Nine of 17 patients reported decreased pain intensities under moderate belt application, four reported no change and four reported increased pain intensity. For the entire population investigated here, this qualitative description was not confirmed on a statistical significant level. Discussion Minute changes were observed in the alignment of the lumbar spine in the frontal plane in SIJ patients. The potential pain-decreasing effects of pelvic belts could not be attributed to altered muscle activity, pelvic morphometry or body balance in a static short-term application. Long-term belt effects will therefore be of prospective interest. PMID:25781325

Pelvic belt effects on pelvic morphometry, muscle activity and body balance in patients with sacroiliac joint dysfunction.

Science.gov (United States)

Soisson, Odette; Lube, Juliane; Germano, Andresa; Hammer, Karl-Heinz; Josten, Christoph; Sichting, Freddy; Winkler, Dirk; Milani, Thomas L; Hammer, Niels

2015-01-01

The sacroiliac joint (SIJ) is frequently involved in low back and pelvic girdle pain. However, morphometrical and functional characteristics related to SIJ pain are poorly defined. Pelvic belts represent one treatment option, but evidence still lacks as to their pain-reducing effects and the mechanisms involved. Addressing these two issues, this case-controlled study compares morphometric, functional and clinical data in SIJ patients and healthy controls and evaluates the effects of short-term pelvic belt application. Morphometric and functional data pertaining to pelvic belt effects were compared in 17 SIJ patients and 17 controls. Lumbar spine and pelvis morphometries were obtained from 3T magnetic resonance imaging. Functional electromyography data of pelvis and leg muscles and center of pressure excursions were measured in one-leg stance. The numerical rating scale was used to evaluate immediate pain-reducing effects. Pelvic morphometry was largely unaltered in SIJ patients and also by pelvic belt application. The angle of lumbar lateral flexion was significantly larger in SIJ patients without belt application. Muscle activity and center of pressure were unaffected by SIJ pain or by belt application in one-leg stance. Nine of 17 patients reported decreased pain intensities under moderate belt application, four reported no change and four reported increased pain intensity. For the entire population investigated here, this qualitative description was not confirmed on a statistical significant level. Minute changes were observed in the alignment of the lumbar spine in the frontal plane in SIJ patients. The potential pain-decreasing effects of pelvic belts could not be attributed to altered muscle activity, pelvic morphometry or body balance in a static short-term application. Long-term belt effects will therefore be of prospective interest.

First-order control of syntectonic sedimentation on crustal-scale structure of mountain belts

Science.gov (United States)

Erdős, Zoltán.; Huismans, Ritske S.; van der Beek, Peter

2015-07-01

The first-order characteristics of collisional mountain belts and the potential feedback with surface processes are predicted by critical taper theory. While the feedback between erosion and mountain belt structure has been fairly extensively studied, less attention has been given to the potential role of synorogenic deposition. For thin-skinned fold-and-thrust belts, recent studies indicate a strong control of syntectonic deposition on structure, as sedimentation tends to stabilize the thin-skinned wedge. However, the factors controlling basement deformation below fold-and-thrust belts, as evident, for example, in the Zagros Mountains or in the Swiss Alps, remain largely unknown. Previous work has suggested that such variations in orogenic structure may be explained by the thermotectonic "age" of the deforming lithosphere and hence its rheology. Here we demonstrate that sediment loading of the foreland basin area provides an additional control and may explain the variable basement involvement in orogenic belts. When examining the role of sedimentation, we identify two end-members: (1) sediment-starved orogenic systems with thick-skinned basement deformation in an axial orogenic core and thin-skinned deformation in the bordering forelands and (2) sediment-loaded orogens with thick packages of synorogenic deposits, derived from the axial basement zone, deposited on the surrounding foreland fold-and-thrust belts, and characterized by basement deformation below the foreland. Using high-resolution thermomechanical models, we demonstrate a strong feedback between deposition and crustal-scale thick-skinned deformation. Our results show that the loading effects of syntectonic sediments lead to long crustal-scale thrust sheets beneath the orogenic foreland and explain the contrasting characteristics of sediment-starved and sediment-loaded orogens, showing for the first time how both thin- and thick-skinned crustal deformations are linked to sediment deposition in these

The Relationship Between KBO Colors and Kuiper-belt Plane Inclination

Science.gov (United States)

Kane, J. F.; Gulbis, A. A. S.; Elliot, J. L.

2005-08-01

The colors of Kuiper belt objects (KBOs) can indicate different compositions, environmental conditions, or formation characteristics within the Kuiper belt. Photometric color observations of these objects, combined with dynamical information, can provide insight into their composition, the extent to which space-weathering or impact gardening have played a role in surface modification, and the processes at work during the formation of our solar system. Data from the Deep Ecliptic Survey (DES; Millis et al., 2002, AJ, 123, 2083) have been used to determine the plane of the Kuiper belt, identifying "core" and "halo" populations with respect to this plane (Elliot et al. 2005, AJ, 129, 1117). Gulbis et al. (2005, Icarus, submitted) found the colors of the core KBOs, those having inclinations within approximately 4.6 degrees of the Kuiper-belt plane, to be primarily red, unlike the halo objects. We have combined newly obtained Sloan g', r', and i' observations from the 6.5-m Clay telescope at Las Campanas Observatory of 12 KBOs with previously published data to examine the transition between these populations as a function of color. By comparing the colors of objects as a function of inclination, we can establish trends distinguishing the core and halo populations. For inclination bins containing equal numbers of KBOs, we find that the percentage of red objects (B-R > median B-R of the sample) decreases in a smooth, but nonlinear fashion. This research is partially supported by an MIT fellowship, an NSF GSRF and NSF grant AST0406493.

REDDY MAIN BELT ASTEROID SPECTRA V1.0

Data.gov (United States)

National Aeronautics and Space Administration — This data set contains low-resolution (R~150) near-infrared (0.7-2.5 microns) spectra of 90 main belt asteroids observed with the SpeX instrument on the NASA...

Critical phenomenon of granular flow on a conveyor belt.

Science.gov (United States)

De-Song, Bao; Xun-Sheng, Zhang; Guang-Lei, Xu; Zheng-Quan, Pan; Xiao-Wei, Tang; Kun-Quan, Lu

2003-06-01

The relationship between the granular wafer movement on a two-dimensional conveyor belt and the size of the exit together with the velocity of the conveyor belt has been studied in the experiment. The result shows that there is a critical speed v(c) for the granular flow when the exit width d is fixed (where d=R/D, D being the diameter of a granular wafers). When vv(c), the flow rate Q is described as Q=Crho(v)(beta)(d-k)(3/2). These are the effects of the interaction among the granular wafers and the change of the states of the granular flow due to the changing of the speed or the exit width d.

Plasmonic graded nano-disks as nano-optical conveyor belt.

Science.gov (United States)

Kang, Zhiwen; Lu, Haifei; Chen, Jiajie; Chen, Kun; Xu, Fang; Ho, Ho-Pui

2014-08-11

We propose a plasmonic system consisting of nano-disks (NDs) with graded diameters for the realization of nano-optical conveyor belt. The system contains a couple of NDs with individual elements coded with different resonant wavelengths. By sequentially switching the wavelength and polarization of the excitation source, optically trapped target nano-particle can be transferred from one ND to another. The feasibility of such function is verified based on the three-dimensional finite-difference time-domain technique and the Maxwell stress tensor method. Our design may provide an alternative way to construct nano-optical conveyor belt with which target molecules can be delivered between trapping sites, thus enabling many on-chip optofluidic applications.

An Estimate of Recoverable Heavy Oil Resources of the Orinoco Oil Belt, Venezuela

Science.gov (United States)

Schenk, Christopher J.; Cook, Troy A.; Charpentier, Ronald R.; Pollastro, Richard M.; Klett, Timothy R.; Tennyson, Marilyn E.; Kirschbaum, Mark A.; Brownfield, Michael E.; Pitman, Janet K.

2009-01-01

The Orinoco Oil Belt Assessment Unit of the La Luna-Quercual Total Petroleum System encompasses approximately 50,000 km2 of the East Venezuela Basin Province that is underlain by more than 1 trillion barrels of heavy oil-in-place. As part of a program directed at estimating the technically recoverable oil and gas resources of priority petroleum basins worldwide, the U.S. Geological Survey estimated the recoverable oil resources of the Orinoco Oil Belt Assessment Unit. This estimate relied mainly on published geologic and engineering data for reservoirs (net oil-saturated sandstone thickness and extent), petrophysical properties (porosity, water saturation, and formation volume factors), recovery factors determined by pilot projects, and estimates of volumes of oil-in-place. The U.S. Geological Survey estimated a mean volume of 513 billion barrels of technically recoverable heavy oil in the Orinoco Oil Belt Assessment Unit of the East Venezuela Basin Province; the range is 380 to 652 billion barrels. The Orinoco Oil Belt Assessment Unit thus contains one of the largest recoverable oil accumulations in the world.

Exploring maize-legume intercropping systems in Southwest Mexico

NARCIS (Netherlands)

Flores-Sanchez, D.; Pastor, A.V.; Lantinga, E.A.; Rossing, W.A.H.; Kropff, M.J.

2013-01-01

Maize yields in continuous maize production systems of smallholders in the Costa Chica, a region in Southwest Mexico, are low despite consistent inputs of fertilizers and herbicides. This study was aimed at investigating the prospects of intercropping maize (Zea mays L.) and maize-roselle (Hibiscus

Asteroid size distributions for the main belt and for asteroid families

Science.gov (United States)

Kazantzev, A.; Kazantzeva, L.

2017-12-01

The asteroid-size distribution for he Eos family was constructed. The WISE database containing the albedo p and the size D of over 80,000 asteroids was used. The b parameter of the power-law dependence has a minimum at some average values of the asteroid size of the family. A similar dependence b(D) exists for the whole asteroid belt. An assumption on the possible similarity of the formation mechanisms of the asteroid belt as a whole and separate families is made.

Goulds Belt, Interstellar Clouds, and the Eocene-Oligocene Helium-3 Spike

Science.gov (United States)

Rubincam, David Parry

2015-01-01

Drag from hydrogen in the interstellar cloud which formed Gould's Belt may have sent small meteoroids with embedded helium to the Earth, perhaps explaining part or all of the (sup 3) He spike seen in the sedimentary record at the Eocene-Oligocene transition. Assuming the Solar System passed through part of the cloud, meteoroids in the asteroid belt up to centimeter size may have been dragged to the resonances, where their orbital eccentricities were pumped up into Earth-crossing orbits.

Children's and Adults' Comfort Experience of Extra Seat Belts When Riding in the Rear Seat of a Passenger Car.

Science.gov (United States)

Osvalder, Anna-Lisa; Hansson, Ida; Bohman, Katarina

2015-01-01

The objective of this study was to explore passengers' comfort experience of extra seat belts during on-road driving in the rear seat of a passenger car and to investigate how the use of extra belts affects children's and adults' attitudes to the product. Two different seat belt systems were tested, criss-cross (CC) and backpack (BP), consisting of the standard 3-point belt together with an additional 2-point belt. In total, 32 participants (15 children aged 6-10, 6 youths aged 11-15, and 11 adults aged 20-79, who differed considerably in size, shape, and proportions) traveled for one hour with each system, including city traffic and highway driving. Four video cameras monitored the test subject during the drive. Subjective data regarding emotions and perceived discomfort were collected in questionnaires every 20 min. A semistructured interview was held afterwards. All participant groups accepted the new products and especially the increased feeling of safety (P car. CC was appreciated for its symmetry, comfort, and the perceived feeling of safety. Some participants found CC unpleasant because the belts tended to slip close to the neck, described as a strangling feeling. BP was simpler to use and did not cause annoyance to the neck in the way CC did. Instead, it felt asymmetric and to some extent less safe than CC. Body size and shape affected seat belt fit to a great extent, which in turn affected the experience of comfort, both initially and over time. Perceived safety benefit and experienced comfort were the most determinant factors for the attitude toward the extra seat belts. The extra seat belts were perceived as being better than the participants had expected before the test, and they became more used to them over time. This exploratory study provided valuable knowledge from a user perspective for further development of new seat belt systems in cars. In addition to an increased feeling of safety, seat belt fit and comfort are supplementary influencing

Validity of maximal isometric knee extension strength measurements obtained via belt-stabilized hand-held dynamometry in healthy adults.

Science.gov (United States)

Ushiyama, Naoko; Kurobe, Yasushi; Momose, Kimito

2017-11-01

[Purpose] To determine the validity of knee extension muscle strength measurements using belt-stabilized hand-held dynamometry with and without body stabilization compared with the gold standard isokinetic dynamometry in healthy adults. [Subjects and Methods] Twenty-nine healthy adults (mean age, 21.3 years) were included. Study parameters involved right side measurements of maximal isometric knee extension strength obtained using belt-stabilized hand-held dynamometry with and without body stabilization and the gold standard. Measurements were performed in all subjects. [Results] A moderate correlation and fixed bias were found between measurements obtained using belt-stabilized hand-held dynamometry with body stabilization and the gold standard. No significant correlation and proportional bias were found between measurements obtained using belt-stabilized hand-held dynamometry without body stabilization and the gold standard. The strength identified using belt-stabilized hand-held dynamometry with body stabilization may not be commensurate with the maximum strength individuals can generate; however, it reflects such strength. In contrast, the strength identified using belt-stabilized hand-held dynamometry without body stabilization does not reflect the maximum strength. Therefore, a chair should be used to stabilize the body when performing measurements of maximal isometric knee extension strength using belt-stabilized hand-held dynamometry in healthy adults. [Conclusion] Belt-stabilized hand-held dynamometry with body stabilization is more convenient than the gold standard in clinical settings.

Paleomagnetism and tectonics of the Jura arcuate mountain belt in France and Switzerland

Science.gov (United States)

Gehring, Andreas U.; Keller, Peter; Heller, Friedrich

1991-02-01

Goethite and hematite in ferriferous oolitic beds of Callovian age from the Jura mountains (Switzerland, France) carry either pre- and/or post-tectonic magnetization. The frequent pre-tectonic origin of goethite magnetization indicates a temperature range during formation of the arcuate Jura mountain belt below the goethite Néel temperature of about 100°C. The scatter of the pre-tectonic paleomagnetic directions ( D = 11.5° E, I = 55.5°; α95 = 4.7) which reside both in goethite and hematite, provides strong evidence that the arcuate mountain belt was shaped without significant rotation. The paleomagnetic results support tectonic thin-skinned models for the formation of the Jura mountain belt.

Energy efficient idler for belt conveyor systems

Energy Technology Data Exchange (ETDEWEB)

Mukhopadhyay, A.K.; Chattopadhyay, A. [Indian School of Mines Univ., Dhanbad (India). Dept. of Mechanical Engineering and Mining; Soni, R.; Bhattnagar, M.

2009-07-01

In today's economic and legal environment, energy efficiency has become more important than ever. This paper proposes a new design of idler rollers for belt conveyors that could help to them even more efficient by reducing their energy consumption and also their CO{sub 2} footprint. (orig.)

RESEARCH ON THE HOMOGENEITY OF TEMPERATURES IN JOINT'S AREA BY VULCANIZING THE CONVEYOR BELTS

Directory of Open Access Journals (Sweden)

Dan DOBROTA

2016-05-01

Full Text Available The researches presented in this paper have followed the analysis of the heat transfer mode during joining through vulcanization of the conveyor belts and also the homogeneity of the temperatures in the joint area. The researches were made under laboratory conditions taking into account the process of joining of two conveyor belts of the type ST 2000 with an installation of the type DSLQ. Temperature measurement was conducted using an EX42570 pyrometer in four distinct points corresponding to each end of the two conveyor belts on the both sides of the band, namely the active and inactive side.

Watershed regressions for pesticides (warp) models for predicting atrazine concentrations in Corn Belt streams

Science.gov (United States)

Stone, Wesley W.; Gilliom, Robert J.

2012-01-01

Watershed Regressions for Pesticides (WARP) models, previously developed for atrazine at the national scale, are improved for application to the United States (U.S.) Corn Belt region by developing region-specific models that include watershed characteristics that are influential in predicting atrazine concentration statistics within the Corn Belt. WARP models for the Corn Belt (WARP-CB) were developed for annual maximum moving-average (14-, 21-, 30-, 60-, and 90-day durations) and annual 95th-percentile atrazine concentrations in streams of the Corn Belt region. The WARP-CB models accounted for 53 to 62% of the variability in the various concentration statistics among the model-development sites. Model predictions were within a factor of 5 of the observed concentration statistic for over 90% of the model-development sites. The WARP-CB residuals and uncertainty are lower than those of the National WARP model for the same sites. Although atrazine-use intensity is the most important explanatory variable in the National WARP models, it is not a significant variable in the WARP-CB models. The WARP-CB models provide improved predictions for Corn Belt streams draining watersheds with atrazine-use intensities of 17 kg/km2 of watershed area or greater.

Beating the Odds. An Educational Program Relating Safety Belt Use to Health Lifestyles for High School Students.

Science.gov (United States)

Department of Transportation, Washington, DC. National Highway Safety Bureau.

This program module is designed to encourage the use of safety measures in driving, emphasizing the use of seat belts. The learning activities focus upon: (1) the importance of the use of safety belts as the most effective preventive measure in a safe and healthy lifestyle; (2) the reasons people cite for not wearing safety belts and the accuracy…

Proterozoic orogenic belts and rifting of Indian cratons: Geophysical constraints

Directory of Open Access Journals (Sweden)

D.C. Mishra

2014-01-01

Full Text Available The Aravalli–Delhi and Satpura Mobile Belts (ADMB and SMB and the Eastern Ghat Mobile Belt (EGMB in India form major Proterozoic mobile belts with adjoining cratons and contemporary basins. The most convincing features of the ADMB and the SMB have been the crustal layers dipping from both sides in opposite directions, crustal thickening (∼45 km and high density and high conductivity rocks in upper/lower crust associated with faults/thrusts. These observations indicate convergence while domal type reflectors in the lower crust suggest an extensional rifting phase. In case of the SMB, even the remnant of the subducting slab characterized by high conductive and low density slab in lithospheric mantle up to ∼120 km across the Purna–Godavari river faults has been traced which may be caused by fluids due to metamorphism. Subduction related intrusives of the SMB south of it and the ADMB west of it suggest N–S and E–W directed convergence and subduction during Meso–Neoproterozoic convergence. The simultaneous E–W convergence between the Bundelkhand craton and Marwar craton (Western Rajasthan across the ADMB and the N–S convergence between the Bundelkhand craton and the Bhandara and Dharwar cratons across the SMB suggest that the forces of convergence might have been in a NE–SW direction with E–W and N–S components in the two cases, respectively. This explains the arcuate shaped collision zone of the ADMB and the SMB which are connected in their western part. The Eastern Ghat Mobile Belt (EGMB also shows signatures of E–W directed Meso–Neoproterozoic convergence with East Antarctica similar to ADMB in north India. Foreland basins such as Vindhyan (ADMB–SMB, and Kurnool (EGMB Supergroups of rocks were formed during this convergence. Older rocks such as Aravalli (ADMB, Mahakoshal–Bijawar (SMB, and Cuddapah (EGMB Supergroups of rocks with several basic/ultrabasic intrusives along these mobile belts, plausibly formed during

The tropical Atlantic surface wind divergence belt and its effect on clouds

OpenAIRE

Y. Tubul; I. Koren; O. Altaratz

2015-01-01

A well-defined surface wind divergence (SWD) belt with distinct cloud properties forms over the equatorial Atlantic during the boreal summer months. This belt separates the deep convective clouds of the intertropical convergence zone (ITCZ) from the shallow marine stratocumulus cloud decks forming over the cold-water subtropical region of the southern Hadley cell. Using the QuikSCAT-SeaWinds and Aqua-MODIS instruments, we examined the large-scale spatiotemporal ...

Geochemical evidence for Paleozoic crustal growth and tectonic conversion in the Northern Beishan Orogenic Belt, southern Central Asian Orogenic Belt

Science.gov (United States)

Yuan, Yu; Zong, Keqing; He, Zhenyu; Klemd, Reiner; Jiang, Hongying; Zhang, Wen; Liu, Yongsheng; Hu, Zhaochu; Zhang, Zeming

2018-03-01

The Beishan Orogenic Belt is located in the central southernmost part of the Central Asian Orogenic Belt (CAOB), which plays a key role in understanding the formation and evolution of the CAOB. Granitoids are the documents of crustal and tectonic evolution in orogenic belts. However, little is known regarding the petrogenesis and geodynamic setting of the widely distributed Paleozoic granitoids in the Northern Beishan Orogenic Belt (NBOB). The present study reveals significant differences concerning the petrogenesis and tectonic setting of early and late Paleozoic granitoids from the NBOB. The early Paleozoic granitoids from the 446-430 Ma Hongliuxia granite complex of the Mazongshan unit and the 466-428 Ma Shibanjing complex of the Hanshan unit show classic I-type granite affinities as revealed by the relative enrichment of LILEs and LREEs, pronounced depletions of Nb, Ta and Ti and the abundant presence of hornblende. Furthermore, they are characterized by strongly variable zircon εHf(t) values between - 16.7 and + 12.8 and evolved plagioclase Sr isotopic compositions of 0.7145-0.7253, indicating the involvement of both juvenile and ancient continental crust in the magma source. Thus, we propose that the early Paleozoic granitoids in the NBOB were generated in a subduction-related continental arc setting. In contrast, the late Paleozoic 330-281 Ma granitoids from the Shuangjingzi complex of the Hanshan unit exhibit positive zircon εHf(t) values between + 5.8 and + 13.2 and relatively depleted plagioclase Sr isotopic compositions of 0.7037-0.7072, indicating that they were mainly formed by remelting of juvenile crust. Thus, an intra-plate extensional setting is proposed to have occurred during formation of the late Paleozoic granitoids. Therefore, between the early and late Paleozoic, the magma sources of the NBOB granitoids converted from the reworking of both juvenile and ancient crusts during a subduction-induced compressional setting to the remelting of

Research on conditional characteristics vision real-time detection system for conveyor belt longitudinal tear

NARCIS (Netherlands)

Qiao, Tiezhu; Li, Xinyu; Pang, Y.; Lü, Yuxiang; Wang, Feng; Jin, Baoquan

2017-01-01

Conveyor belt longitudinal tear is one of the most serious problems in coal mining. Existing systems cannot realise lossless and real-time detection for longitudinal tear of conveyor belt. Currently, visual detecting systems are proposed by many researchers and are becoming the future trend. A

Spinner dolphins Stenella longirostris off south-west Mauritius ...

African Journals Online (AJOL)

Spinner dolphins Stenella longirostris longirostris off the south-west coast of Mauritius are subject to ongoing anthropogenic disturbance in the form of daily dolphin tourism, which has intensified since 1998. Abundance of this species was estimated using photo-identification data and mark-recapture analysis. Between April ...

Raně středověké kování a část přezky z Meclova-Březí

Czech Academy of Sciences Publication Activity Database

Profantová, Naďa; Řezáč, M.

2014-01-01

Roč. 2014, č. 7 (2014), s. 71-77 ISSN 1804-2953 Institutional support: RVO:67985912 Keywords : bronze belt adornments * South-West Bohemia * Early Middle Ages * long-distance communication * Regensburg Road Subject RIV: AC - Archeology, Anthropology, Ethnology

Earthquake-triggered landslides in southwest China

OpenAIRE

X. L. Chen; Q. Zhou; H. Ran; R. Dong

2012-01-01

Southwest China is located in the southeastern margin of the Tibetan Plateau and it is a region of high seismic activity. Historically, strong earthquakes that occurred here usually generated lots of landslides and brought destructive damages. This paper introduces several earthquake-triggered landslide events in this region and describes their characteristics. Also, the historical data of earthquakes with a magnitude of 7.0 or greater, having occurred in this region, is col...

Echinococcus granulosus Prevalence in Dogs in Southwest Nigeria

Directory of Open Access Journals (Sweden)

Oyeduntan Adejoju Adediran

2014-01-01

Full Text Available Echinococcosis is a public health parasitic disease that is cosmopolitan (Echinococcus granulosus in its distribution. Domestic dogs (Canis familiaris have been recognised as the definitive host of the parasite. The present study was carried out to determine the prevalence of canine echinococcosis in Southwest Nigeria using direct enzyme linked immunosorbent assay (ELISA to detect sera antigen. Two hundred and seventy-three (273 canine sera were tested for the presence of Echinococcus antigen. Purpose of keeping (hunting or companion, age (young or adult, and sex of each dog were considered during sampling. Total prevalence recorded was 12.45% (34/273. There was significant difference (P0.05 between young and adult dogs. There was no association between sex and prevalence of canine echinococcosis. The result of this study established the presence of canine echinococcosis in Southwest Nigeria; thus there is the possibility of occurrence of zoonotic form of the disease (human cystic hydatid diseases in the region.

Powerful conveyer belt real-time online detection system based on x-ray

Science.gov (United States)

Rong, Feng; Miao, Chang-yun; Meng, Wei

2009-07-01

The powerful conveyer belt is widely used in the mine, dock, and so on. After used for a long time, internal steel rope of the conveyor belt may fracture, rust, joints moving, and so on .This would bring potential safety problems. A kind of detection system based on x-ray is designed in this paper. Linear array detector (LDA) is used. LDA cost is low, response fast; technology mature .Output charge of LDA is transformed into differential voltage signal by amplifier. This kind of signal have great ability of anti-noise, is suitable for long-distance transmission. The processor is FPGA. A IP core control 4-channel A/D convertor, achieve parallel output data collection. Soft-core processor MicroBlaze which process tcp/ip protocol is embedded in FPGA. Sampling data are transferred to a computer via Ethernet. In order to improve the image quality, algorithm of getting rid of noise from the measurement result and taking gain normalization for pixel value is studied and designed. Experiments show that this system work well, can real-time online detect conveyor belt of width of 2.0m and speed of 5 m/s, does not affect the production. Image is clear, visual and can easily judge the situation of conveyor belt.

Channel belt architecture formed by a meandering river

NARCIS (Netherlands)

Lageweg, W.I. van de; Dijk, W.M. van; Kleinhans, M.G.

2013-01-01

Stratification in channel belts is the key to reconstructing formative channel dimensions and palaeoflow conditions; this requires an understanding of the relation between river morphodynamics and set thickness. So far, theories for reconstruction of the original morphology from preserved

The Lufilian arc and Irumide belt of Zambia: Results of a geotraverse across their intersection

Science.gov (United States)

Daly, M. C.; Chakraborty, S. K.; Kasolo, P.; Musiwa, M.; Mumba, P.; Naidu, B.; Namateba, C.; Ngambi, O.; Coward, M. P.

The Kibaran aged Irumide belt and the Pan African aged Lufilian arc intersect in central Zambia. The Irumide belt is a thrust belt comprising northwesterly verging structures in the north, upright structures in the central zone and southeasterly verging structures in the south. Tectonic transport, as deduced from regional stretching lineations, changes across the central upright zone. To the north of this zone, movement is to the northwest; to the south of the zone, movement is to the southeast. This divergence of structures about a central upright zone is recognized throughout the belt. The Lufilian arc comprises a northeasterly verging thrust belt involving large basement thrust sheets forming domal culimations throughoutregion. These thrusts climb up-section towards the northeast and have telescoped the Katangan stratigraphy. In the Copperbelt area of the arc, the Irumide and Lufilian structures are separated by a marked unconformity. However in the Mubalashi area, south of the Copperbelt, there is aa coincidence of strike of Lufilian and Irumide structures which, in the past, has made their separation difficult. The structures can be separated on the basis of stretching lineations associated with the deformation. In the ENE striking Lufilian structures stretching lineations are seen to be sub-horizontal, suggesting a lateral ramp relationship to the main Lufilian deformation. Similar striking Irumide structures have a steeply plunging down dip lineation. The intersection of these two belts represents the junction of two different tectonic systems operating in Africa during the Late Proterozoic.

The impact of radiation belts region on top side ionosphere condition during last solar minimum.

Science.gov (United States)

Rothkaehl, Hanna; Przepiórka, Dororta; Matyjasiak, Barbara

2014-05-01

The wave particle interactions in radiation belts region are one of the key parameters in understanding the global physical processes which govern the near Earth environment. The populations of outer radiation belts electrons increasing in response to changes in the solar wind and the interplanetary magnetic field, and decreasing as a result of scattering into the loss cone and subsequent absorption by the atmosphere. The most important question in relation to understanding the physical processes in radiation belts region relates to estimate the ratio between acceleration and loss processes. This can be also very useful for construct adequate models adopted in Space Weather program. Moreover the wave particle interaction in inner radiation zone and in outer radiation zone have significant influence on the space plasma property at ionospheric altitude. The aim of this presentation is to show the manifestation of radiation belts region at the top side ionosphere during the last long solar minimum. The presentation of longitude and seasonal changes of plasma parameters affected by process occurred in radiation belts region has been performed on the base of the DEMETER and COSMIC 3 satellite registration. This research is partly supported by grant O N517 418440

Benthic fauna of southwest and southeast coasts of India

Digital Repository Service at National Institute of Oceanography (India)

Devi, K.S.; Sheba, P.; Balasubramanian; Venugopal, P.; Sankaranarayanan, V.N.

Benthos, sediments characteristics and organic matter content were studied along southwest and southeast coasts of India. Number of groups/species varied with the stations and also with the depths. Population density was very low in southeast coast...

The Security Challenges of the “One Belt, One Road” Initiative and China’s Choices

Directory of Open Access Journals (Sweden)

Haiquan Liu

2017-08-01

Full Text Available The Silk Road Economic Belt and the 21st Century Maritime Silk Road initiatives (“One Belt, One Road” are of significance in enhancing China’s open economy. This article explores the dual security challenges faced by the “One Belt, One Road” initiative. These challenges include both traditional security challenges, such as great power competition, territorial and island disputes, and political turmoil in the region, as well as non-traditional threats such as terrorism, piracy, and transnational organized crime. This article analyzes the present situation of security cooperation in the region covered by “One Belt, One Road” and also suggests that China needs to pay special attention to three issues, namely the supply of public security goods, the interests of the United States and Russia, and the pivot of Pakistan, besides developing its own strength.

2012 Southwest Florida Water Management District (SWFWMD) Lidar: Lake Manatee

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Geographic Information System (GIS). Southwest Florida Water Management District (SWFWMD) regularly uses digital topographic information to support regulatory, land...

The tropical Atlantic surface wind divergence belt and its effect on clouds

OpenAIRE

Y. Tubul; I. Koren; O. Altaratz

2015-01-01

A well-defined surface wind divergence (SWD) belt with distinct cloud properties forms over the equatorial Atlantic during the boreal summer months. This belt separates the deep convective clouds of the Intertropical Convergence Zone (ITCZ) from the shallow marine stratocumulus cloud decks forming over the cold-water subtropical region of the southern branch of the Hadley cell in the Atlantic. Using the QuikSCAT-SeaWinds and Aqua-MODIS instruments, we examined the large-scal...

Medical back belt with integrated neuromuscular electrical stimulation

NARCIS (Netherlands)

Bottenberg, E. (Eliza); Brinks, G.J. (Ger); Hesse, J. (Jenny)

2014-01-01

The medical back belt with integrated neuromuscular electrical stimulation is anorthopedic device, which has two main functions. The first function is to stimulate the backmuscles by using a neuromuscular electrical stimulation device that releases regular,electrical impulses. The second function of

Perception of physiotherapy educators in southwest Nigeria on ...

African Journals Online (AJOL)

The aim of this study was to seek opinions regarding the perceived advantages and disadvantages of the models of clinical education used in south-west, Nigeria. Seventy- four (45 males, 29 females) physiotherapy educators participated in this cross-sectional population-based survey. They were recruited from the three ...

Three-dimensional data assimilation and reanalysis of radiation belt electrons: Observations of a four-zone structure using five spacecraft and the VERB code

Science.gov (United States)

Kellerman, A. C.; Shprits, Y. Y.; Kondrashov, D.; Subbotin, D.; Makarevich, R. A.; Donovan, E.; Nagai, T.

2014-11-01

Obtaining the global state of radiation belt electrons through reanalysis is an important step toward validating our current understanding of radiation belt dynamics and for identification of new physical processes. In the current study, reanalysis of radiation belt electrons is achieved through data assimilation of five spacecraft with the 3-D Versatile Electron Radiation Belt (VERB) code using a split-operator Kalman filter technique. The spacecraft data are cleaned for noise, saturation effects, and then intercalibrated on an individual energy channel basis, by considering phase space density conjunctions in the T96 field model. Reanalysis during the CRRES era reveals a never-before-reported four-zone structure in the Earth's radiation belts during the 24 March 1991 shock-induced injection superstorm: (1) an inner belt, (2) the high-energy shock-injection belt, (3) a remnant outer radiation belt, and (4) a second outer radiation belt. The third belt formed near the same time as the second belt and was later enhanced across keV to MeV energies by a second particle injection observed by CRRES and the Northern Solar Terrestrial Array riometer network. During the recovery phase of the storm, the fourth belt was created near L*=4RE, lasting for several days. Evidence is provided that the fourth belt was likely created by a dominant local heating process. This study outlines the necessity to consider all diffusive processes acting simultaneously and the advantage of supporting ground-based data in quantifying the observed radiation belt dynamics. It is demonstrated that 3-D data assimilation can resolve various nondiffusive processes and provides a comprehensive picture of the electron radiation belts.

Scheelite distribution a long of amphibolitic belt from greenstone belt Barbacena, Minas Gerais, Brazil

International Nuclear Information System (INIS)

Pereira, R.M.; Alexandre, C.A.

1990-01-01

In the middle southern portion of the Minas Gerais state a 60 Km long and 12 Km wide tungsten belt was discovered, and related to the amphibolitic rocks of the Barbacena Greenstone. Tungsten, present as scheelite, is associated with amphibolites, amphibole schists and amphibole gneisses, with chemical characteristics indicating an igneous origin. Chemical analyses on pan concentrates by I.C.P. showed high values on lead, tin, yttrium, lanthanum, cerium and zirconium, and average values for zinc and copper. The scheelite mineralization is probably strata bound and has a possible submarine exhalative origin. (author)

Linking main-belt comets to asteroid families

Science.gov (United States)

Novakovic, B.; Hsieh, H. H.; Cellino, A.

2012-09-01

Here we present our results obtained by applying different methods in order to establish a firm link between the main-belt comets (MBCs) and colisionally-formed asteroid families (AFs), i.e, to possibly find additional line of evidence supporting the hypothesis that MBCs may be preferentially found among the members of young AFs.

A six-part collisional model of the main asteroid belt

Science.gov (United States)

Cibulková, H.; Brož, M.; Benavidez, P. G.

2014-10-01

In this work, we construct a new model for the collisional evolution of the main asteroid belt. Our goals are to test the scaling law of Benz and Asphaug (Benz, W., Asphaug, E. [1999]. Icarus, 142, 5-20) and ascertain if it can be used for the whole belt. We want to find initial size-frequency distributions (SFDs) for the considered six parts of the belt (inner, middle, “pristine”, outer, Cybele zone, high-inclination region) and to verify if the number of synthetic asteroid families created during the simulation matches the number of observed families as well. We used new observational data from the WISE satellite (Masiero et al., 2011) to construct the observed SFDs. We simulate mutual collisions of asteroids with a modified version of the Boulder code (Morbidelli, A., et al. [2009]. Icarus, 204, 558-573), where the results of hydrodynamic (SPH) simulations of Durda et al. (Durda, D.D., et al. [2007]. Icarus, 498-516) and Benavidez et al. (Benavidez, P.G., et al. [2012]. 219, 57-76) are included. Because material characteristics can significantly affect breakups, we created two models - for monolithic asteroids and for rubble-piles. To explain the observed SFDs in the size range D=1 to 10 km we have to also account for dynamical depletion due to the Yarkovsky effect. The assumption of (purely) rubble-pile asteroids leads to a significantly worse fit to the observed data, so that we can conclude that majority of main-belt asteroids are rather monolithic. Our work may also serve as a motivation for further SPH simulations of disruptions of smaller targets (with a parent body size of the order of 1 km).

Anomalous heat flow belt along the continental margin of Brazil

Science.gov (United States)

Hamza, Valiya M.; Vieira, Fabio P.; Silva, Raquel T. A.

2018-01-01

A comprehensive analysis of thermal gradient and heat flow data was carried out for sedimentary basins situated in the continental margin of Brazil (CMB). The results point to the existence of a narrow belt within CMB, where temperature gradients are higher than 30 °C/km and the heat flow is in excess of 70 mW/m2. This anomalous geothermal belt is confined between zones of relatively low to normal heat flow in the adjacent continental and oceanic regions. The width of the belt is somewhat variable, but most of it falls within the range of 100-300 km. The spatial extent is relatively large in the southern (in the basins of Pelotas, Santos and Campos) and northern (in the basins of Potiguar and Ceará) parts, when compared with those in the central parts (in the basins of South Bahia, Sergipe and Alagoas). The characteristics of heat flow anomalies appear to be compatible with those produced by thermal sources at depths in the lower crust. Hence, magma emplacement at the transition zone between lower crust and upper mantle is considered the likely mechanism producing such anomalies. Seismicity within the belt is relatively weak, with focal depths less than 10 km for most of the events. Such observations imply that "tectonic bonding" between continental and oceanic segments, at the transition zone of CMB, is relatively weak. Hence, it is proposed that passive margins like CMB be considered as constituting a type of plate boundary that is aseismic at sub-crustal levels, but allows for escape of significant amounts of earth's internal heat at shallow depths.

Quantification of fold growth of frontal antiforms in the Zagros fold and thrust belt (Kurdistan, NE Iraq)

Science.gov (United States)

Bretis, Bernhard; Bartl, Nikolaus; Graseman, Bernhard; Lockhart, Duncan

2010-05-01

The Zagros fold and thrust belt is a seismically active orogen, where actual kinematic models based on GPS networks suggest a north-south shortening between Arabian and Eurasian in the order of 1.5-2.5 cm/yr. Most of this deformation is partitioned in south-southwest oriented folding and thrusting with northwest-southeast to north-south trending dextral strike slip faults. The Zagros fold and thrust belt is of great economic interest because it has been estimated that this area contains about 15% of the global recoverable hydrocarbons. Whereas the SE parts of the Zagros have been investigated by detailed geological studies, the NW extent being part of the Republic of Iraq have experienced considerably less attention. In this study we combine field work and remote sensing techniques in order to investigate the interaction of erosion and fold growth in the area NE of Erbil (Kurdistan, Iraq). In particular we focus on the interaction of the transient development of drainage patterns along growing antiforms, which directly reflects the kinematics of progressive fold growth. Detailed geomorphological studies of the Bana Bawi-, Permam- and Safeen fold trains show that these anticlines have not developed from subcylindrical embryonic folds but they have merged from different fold segments that joined laterally during fold amplification. This fold segments with length between 5 and 25 km have been detected by mapping ancient and modern river courses that initially cut the nose of growing folds and eventually got defeated leaving behind a wind gap. Fold segments, propagating in different directions force rivers to join resulting in steep gorges, which dissect the merging fold noses. Along rapidly lateral growing folds (e.g. at the SE end of the Bana Bawi Anticline) we observed "curved wind gaps", a new type of abandoned river course, where form of the wind gap mimics a formed nose of a growing antiform. The inherited curved segments of uplifted curved river courses strongly

Telescoping metamorphic isograds: Evidence from 40Ar/39A dating in the Orange-Milford belt, southern Connecticut

Science.gov (United States)

Kunk, Michael J.; Walsh, Gregory J.; Growdon, Martha L.; Wintsch, Robert P.

2013-01-01

New 40Ar/39Ar ages for hornblende and muscovite from the Orange-Milford belt in southern Connecticut reflect cooling from Acadian amphibolite facies metamorphism between ∼380 to 360 Ma followed by retrograde recrystallization of fabric-forming muscovite and chlorite during lower greenschist facies Alleghanian transpression at ∼280 Ma. Reported field temperature and pressure gradients are improbably high for these rocks and a NW metamorphic field gradient climbing from chlorite-grade to staurolite-grade occurs over less than 5 km. Simple tilting cannot account for this compressed isograd spacing given the geothermal gradient of ∼20 °C/km present at the time of regional metamorphism. However, post-metamorphic transpression could effectively telescope the isograds by stretching the belt at an oblique angle to the isograd traces. Textures in the field and in thin section reveal several older prograde schistosities overprinted by lower greenschist facies fabrics. The late cleavages commonly occur at the scale of ∼100 μm and these samples contain multiple age populations of white mica. 40Ar/39Ar analysis of these poly-metamorphic samples with mixed muscovite populations yield climbing or U-shaped age spectra. The ages of the low temperature steps are late Paleozoic, while the ages of the older steps are late Devonian. These results support our petrologic interpretation that the younger cleavage developed under metamorphic conditions below the closure temperature for Ar diffusion in muscovite, that is, in the lower greenschist facies. The correlation of a younger regionally reproducible age population with a pervasive retrograde muscovite ± chlorite cleavage reveals an Alleghanian (∼280 Ma) overprint on the Acadian metamorphic gradient (∼380 Ma). Outcrop-scale structures including drag folds and imbricate boudins suggest that Alleghanian deformation and cleavage development occurred in response to dextral transpression along a northeast striking boundary

Focused seismicity triggered by flank instability on Kīlauea's Southwest Rift Zone

Science.gov (United States)

Judson, Josiah; Thelen, Weston A.; Greenfield, Tim; White, Robert S.

2018-03-01

Swarms of earthquakes at the head of the Southwest Rift Zone on Kīlauea Volcano, Hawai´i, reveal an interaction of normal and strike-slip faulting associated with movement of Kīlauea's south flank. A relocated subset of earthquakes between January 2012 and August 2014 are highly focused in space and time at depths that are coincident with the south caldera magma reservoir beneath the southern margin of Kīlauea Caldera. Newly calculated focal mechanisms are dominantly dextral shear with a north-south preferred fault orientation. Two earthquakes within this focused area of seismicity have normal faulting mechanisms, indicating two mechanisms of failure in very close proximity (10's of meters to 100 m). We suggest a model where opening along the Southwest Rift Zone caused by seaward motion of the south flank permits injection of magma and subsequent freezing of a plug, which then fails in a right-lateral strike-slip sense, consistent with the direction of movement of the south flank. The seismicity is concentrated in an area where a constriction occurs between a normal fault and the deeper magma transport system into the Southwest Rift Zone. Although in many ways the Southwest Rift Zone appears analogous to the more active East Rift Zone, the localization of the largest seismicity (>M2.5) within the swarms to a small volume necessitates a different model than has been proposed to explain the lineament outlined by earthquakes along the East Rift Zone.

An under-belt capacitance and γ-ray backscatter gauge for on-line determination of moisture in coal

International Nuclear Information System (INIS)

Cutmore, N.G.; Roczniok, A.F.; Sowerby, B.D.

1987-01-01

A non-contacting under-belt capacitance and γ-ray backscatter technique has been developed for on-line measurement of moisture in coal. In this technique, moisture was correlated with radiofrequency susceptance and conductance, determined using an under-belt capacitance sensor in which a fringing electric field interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variation in the density and thickness of the coal layer, an under-belt γ-ray backscatter gauge was used to measure an equivalent volume of coal. Laboratory measurements have shown that this technique compensates more accurately for density and thickness than does their direct physical measurement. (author)

A social media program to increase adolescent seat belt use.

Science.gov (United States)

Drake, Stacy A; Zhang, Ni; Applewhite, Courtney; Fowler, Katherine; Holcomb, John B

2017-09-01

In response to motor vehicle crashes remaining the leading cause of death for teenagers in the United States, a nursing clinical group (n = 10) in conjunction with a local hospital injury prevention program created an educational campaign to bolster seat belt use. The nursing students created an Instagram account to serve as an educational tool to promote seat belt use among teenagers aged 14-19, and the program was presented at three high school health fairs. In all, 135 postings were made to the account over a 3-month period. The number of likes posted by high school students was the unit of analysis. The most significant result (p = .01) was the difference between postings most liked (celebrities wearing seat belts) and least liked (postings made at the high school health fair), otherwise, differences among postings liked (humor postings, response requests, pictures of celebrities, factual data) were not significant. Instagram user engagement, measured in number of likes, is indicative that social media provides platforms to promote injury prevention efforts. Further research is needed to identify measurable elements of social media and to follow-up on behavioral changes following participation. © 2017 Wiley Periodicals, Inc.

Mud Banks along the southwest coast of India are not too muddy for plankton.

Science.gov (United States)

Jyothibabu, R; Balachandran, K K; Jagadeesan, L; Karnan, C; Arunpandi, N; Naqvi, S W A; Pandiyarajan, R S

2018-02-07

Considering Alappuzha Mud Bank in the southern Kerala coast as a typical case of biologically productive Mud Banks that form along the southwest coast of India during the Southwest Monsoon (June - September), the present study addresses several pertinent missing links between the physical environment in Mud Banks and their influence on plankton stock. This study showed that very strong coastal upwelling prevails in the entire study domain during the Southwest Monsoon, which manifests itself in the form of significantly cool, hypoxic and nitrate-rich waters surfacing near the coast. The upwelled water persisting throughout the Southwest Monsoon period was found to have fuelled the exceptionally high phytoplankton stock in the entire study area, including the Mud Bank region. Having accepted that Mud Banks are special because of the calm sea surface conditions and relatively high turbidity level in the water column around them, the present study showed that except at points close to the sea bottom, turbidity level in the Alappuzha Mud Bank was below the critical level to inhibit the plankton stock. The suspended sediments that form in the Mud Bank occasionally could be attributed to the disturbance of the bottom fluid muddy layer and their vertical spurts.

Torque-transmitting mechanism of a metal CVT belt; Kinzoku CVT belt no torque dentatsu mechanism

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, D; Mabuchi, Y; Kato, Y [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

The slip mechanism of a metal CVT belt which consisted of several hundred V-shaped elements and two sets of laminated metal rings was analyzed by focusing on the distribution of the gaps occurring between the elements, and a simulation which could predict the slip-limit torque at which the slip ratio increases sharply was developed. In this paper, the outline of the simulation is shown with some comparison between the calculated results and the experimental data. 3 refs., 13 figs.

Motivating safety belt use at a community hospital: an effective integration of incentive and commitment strategies.

Science.gov (United States)

Nimmer, J G; Geller, E S

1988-06-01

An effective hospital-based safety-belt program incorporated several advantages over prior attempts to increase safety belt use, including (a) the use of indigenous staff as program sponsors, coordinators, and delivery agents; (b) a yearlong program evaluation; and (c) a combination of extrinsic incentives and intrinsic commitment. To be eligible for a weekly $5, employees met the following contingencies: (a) signed a pledge card; (b) displayed the signed pledge card in their vehicle; and (c) wore a safety belt. Overall, belt use increased from a 2-week baseline mean of 15.6% to 34.7% during the 6-month intervention, and decreased to 25.6% at withdrawal. For the pledge card signers (n = 188) and the nonsigners (n = 533), belt use increased from baseline means of 29.4% and 11.8% to intervention use rates of 75.1 and 17.7%, respectively. Withdrawal and 4-month follow-up use rates were 56.0% and 44.9% for the Pledge group, and 17.2% and 22.1% for the Nonpledge group.

Discriminating the biophysical impacts of coastal upwelling and mud banks along the southwest coast of India

Science.gov (United States)

Karnan, C.; Jyothibabu, R.; Arunpandi, N.; Jagadeesan, L.; Muraleedharan, K. R.; Pratihari, A. K.; Balachandran, K. K.; Naqvi, S. W. A.

2017-08-01

Coastal upwelling and mud banks are two oceanographic processes concurrently operating along certain stretches of the southwest (Kerala) coast of India during the Southwest Monsoon period (June-September), facilitating significant enhancement in plankton biomass. Mud banks have scientific and societal attention from time immemorial, predominantly due to the large fisheries associated with them. In this paper, for the first time, the specific biophysical roles of these oceanographic processes have been discriminated, based on a focused 18 weekly/fortnightly time-series study (April to September 2014) in a mud bank-upwelling area (off Alappuzha, southwest coast of India). In conjunction with standard hydrographical and satellite remote sensing data, we utilised a FlowCAM to track the biophysical linkage in terms of plankton composition abundance and size structure at three locations (M1, M2 and M3) in the study area. During the Pre-Southwest Monsoon (April-May), the entire study area was warmer with low nitrate concentration in the surface waters, which caused lower biomass of autotrophs compared to the Southwest Monsoon (June-September). By the onset of the Southwest Monsoon (June), drastic hydrographical transformations took place in the study domain due to the Coastal upwelling, reflected as the surfacing of significantly cool, high nutrient and hypoxic waters. Concurrently, mud bank formed at location M2 due to the presence of relatively high-suspended sediments in the region, creating a localised calm environment conducive for fishing activities. In response to the hydrographical transformations in the entire study area during the Southwest Monsoon, the autotrophic plankton biomass and size structure experienced significant change. The micro-autotrophs biomass that was low during the Pre-Southwest Monsoon (av. 0.33 ± 0.2 mgC L- 1 at surface and av. 0.07 ± 0.04 mgC L- 1 at subsurface) noticeably increased during the Southwest Monsoon (av. 1.6 ± 0.4 mgC L- 1 at

Minimising the fire hazard from the use of belt conveyors in intake roadways

Energy Technology Data Exchange (ETDEWEB)

Leeming, J.R. [Health and Safety Executive, Sheffield, S. Yorkshire (United Kingdom)

2010-07-01

The fire that occurred a the Creswell underground coal mine in Derbyshire in 1950 in which 90 miners lost their lives was caused by a damaged rubber conveyor belt that ignited after being friction heated. The fire propagated along the intake trunk roadway by the burning belt itself, which ignited the timber roadway supports and hampered fire-fighting efforts. This paper demonstrated that operating conveyors in intake trunk roadways presents a risk that products of combustion can be carried to the working areas of a mine via ventilation pathways, thus creating a hazard to the underground miners. In North America, the use of belt air is not commonly used to ventilate working areas. However, these arrangements are common in the United Kingdom. As such, installation, inspection and maintenance standards have been created to minimize the risk of fire in underground, remotely operated belt conveyors in underground mines. Monitoring systems are also in place for early detection of any fire. A review of recent underground fires in the United Kingdom has shown that the measures adopted have been successful in avoiding uncontrollable fires. 13 refs., 5 figs.

Magma Supply of Southwest Indian Ocean: Implication from Crustal Thickness Anomalies

Science.gov (United States)

Chiheng, L.; Jianghai, L.; Huatian, Z.; Qingkai, F.

2017-12-01

The Southwest Indian Ridge (SWIR) is one of the world's slowest spreading ridges with a full spreading rate of 14mm a-1, belonging to ultraslow spreading ridge, which are a novel class of spreading centers symbolized by non-uniform magma supply and crustal accretion. Therefore, the crustal thickness of Southwest Indian Ocean is a way to explore the magmatic and tectonic process of SWIR and the hotspots around it. Our paper uses Residual Mantle Bouguer Anomaly processed with the latest global public data to invert the relative crustal thickness and correct it according to seismic achievements. Gravity-derived crustal thickness model reveals a huge range of crustal thickness in Southwest Indian Ocean from 0.04km to 24km, 7.5km of average crustal thickness, and 3.5km of standard deviation. In addition, statistics data of crustal thickness reveal the frequency has a bimodal mixed skewed distribution, which indicates the crustal accretion by ridge and ridge-plume interaction. Base on the crustal thickness model, we divide three types of crustal thickness in Southwest Indian Ocean. About 20.31% of oceanic crust is 9.8km thick as thick crust. Furthermore, Prominent thin crust anomalies are associated with the trend of most transform faults, but thick crust anomalies presents to northeast of Andrew Bain transform fault. Cold and depleted mantle are also the key factors to form the thin crust. The thick crust anomalies are constrained by hotspots, which provide abundant heat to the mantle beneath mid-ocean ridge or ocean basin. Finally, we roughly delineate the range of ridge-plume interaction and transform fault effect.

Canadian radiation belt science in the ILWS era

Science.gov (United States)

Mann, I. R.

The Outer Radiation Belt Injection, Transport, Acceleration, and Loss Satellite (ORBITALS) is a Canadian Space Agency small satellite mission proposed as a Canadian contribution to the satellite infrastructure for the International Living With a Star (ILWS) program. Planned to operate contemporaneously with the NASA Radiation Belt Storm Probes (RBSP), the ORBITALS will monitor the energetic electron and ion populations in the inner magnetosphere across a wide range of energies (keV to tens of MeV) as well as the dynamic electric and magnetic fields, waves, and cold plasma environment which govern the injection, transport, acceleration and loss of these energetic and space weather critical particle populations in the inner magnetosphere. Currently in Phase A Design Study, the ORBITALS will be launched into a low-inclination GTO-like orbit which every second orbit maximizes the long lasting apogee-pass conjunctions with both the ground-based instruments of the Canadian Geospace Monitoring (CGSM) array as well as with the GOES East and West and geosynchronous communications satellites in the North American sector. In a twelve-hour orbit, every second apogee will conjunct with instrumentation 180 degree in longitude away in the Asian sector. Specifically, the ORBITALS will make the measurements necessary to reach reveal fundamental new understanding of the relative importance of different physical processes (for example VLF verses ULF waves) which shape the energetic particle populations in the inner magnetosphere, as well as providing the raw radiation measurements at MEO altitudes necessary for the development of the next-generation of radiation belt specification models. On-board experiments will also monitor the dose, single event upset, and deep-dielectric charging responses of electronic components on-orbit. Supporting ground-based measurements of ULF and higher frequency wave fields from the Canadian CARISMA (www.carisma.ca) magnetometer array, as well as from

Usefulness of abdominal belt for restricting respiratory cardiac motion and improving image quality in myocardial perfusion PET.

Science.gov (United States)

Ichikawa, Yasutaka; Tomita, Yoya; Ishida, Masaki; Kobayashi, Shigeki; Takeda, Kan; Sakuma, Hajime

2018-04-01

The current study evaluated the usefulness of a belt technique for restricting respiratory motion of the heart and for improving image quality of 13 N-ammonia myocardial PET/CT, and it assessed the tolerability of the belt technique in the clinical setting. Myocardial 13 N-ammonia PET/CT scanning was performed in 8 volunteers on Discovery PET/CT 690 with an optical respiratory motion tracking system. Emission scans were performed with and without an abdominal belt. The amplitude of left ventricular (LV) respiratory motion was measured on respiratory-gated PET images. The degree of erroneous decreases in regional myocardial uptake was visually assessed on ungated PET images using a 5-point scale (0 = normal, 1/2/3 = mild/moderate/severe decrease, 4 = defect). The tolerability of the belt technique was evaluated in 53 patients. All subjects tolerated the belt procedure. The amplitude of the LV respiratory motion decreased significantly with the belt (8.1 ± 7.1 vs 12.1 ± 6.1 mm, P = .0078). The belt significantly improved the image quality scores in the anterior (0.29 ± 0.81 vs 0.71 ± 1.04, P = .015) and inferior (0.33 ± 0.92 vs 1.04 ± 1.04, P PET/CT, and it is well tolerated by patients.

49 CFR 392.16 - Use of seat belts.

Science.gov (United States)

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS DRIVING OF COMMERCIAL MOTOR VEHICLES Driving of Commercial Motor Vehicles § 392.16 Use of seat belts. A commercial motor vehicle which...

Earthquake activity along the Himalayan orogenic belt

Science.gov (United States)

Bai, L.; Mori, J. J.

2017-12-01

The collision between the Indian and Eurasian plates formed the Himalayas, the largest orogenic belt on the Earth. The entire region accommodates shallow earthquakes, while intermediate-depth earthquakes are concentrated at the eastern and western Himalayan syntaxis. Here we investigate the focal depths, fault plane solutions, and source rupture process for three earthquake sequences, which are located at the western, central and eastern regions of the Himalayan orogenic belt. The Pamir-Hindu Kush region is located at the western Himalayan syntaxis and is characterized by extreme shortening of the upper crust and strong interaction of various layers of the lithosphere. Many shallow earthquakes occur on the Main Pamir Thrust at focal depths shallower than 20 km, while intermediate-deep earthquakes are mostly located below 75 km. Large intermediate-depth earthquakes occur frequently at the western Himalayan syntaxis about every 10 years on average. The 2015 Nepal earthquake is located in the central Himalayas. It is a typical megathrust earthquake that occurred on the shallow portion of the Main Himalayan Thrust (MHT). Many of the aftershocks are located above the MHT and illuminate faulting structures in the hanging wall with dip angles that are steeper than the MHT. These observations provide new constraints on the collision and uplift processes for the Himalaya orogenic belt. The Indo-Burma region is located south of the eastern Himalayan syntaxis, where the strike of the plate boundary suddenly changes from nearly east-west at the Himalayas to nearly north-south at the Burma Arc. The Burma arc subduction zone is a typical oblique plate convergence zone. The eastern boundary is the north-south striking dextral Sagaing fault, which hosts many shallow earthquakes with focal depth less than 25 km. In contrast, intermediate-depth earthquakes along the subduction zone reflect east-west trending reverse faulting.

Belts and Chains. FOS: Fundamentals of Service.

Science.gov (United States)

John Deere Co., Moline, IL.

This manual on belts and chain drives is one of a series of power mechanics texts and visual aids on theory, of operation, diagnosis, and repair of automotive and off-the-road agricultural and construction equipment. Materials provide basic information and illustrations for use by vocational students and teachers as well as shop servicemen and…

MULTI-OBJECTIVE OPTIMAL NUMBER AND LOCATION FOR STEEL OUTRIGGER-BELT TRUSS SYSTEM

OpenAIRE

MEHDI BABAEI

2017-01-01

During the past two decades, outrigger-belt truss system has been investigated and used in design of tall buildings. Most of the studies focused on the optimization of the system for minimum displacement and some of them proposed the best locations. In this study, however, multi-objective optimization of tall steel frames with belt trusses is investigated to minimize displacement and weight of the structure. For this purpose, structures with 20, 30, 40, and 50 stories are considered as ...

Brusque belt: a monocyclic evolution ?

International Nuclear Information System (INIS)

Basei, M.A.S.

1990-01-01

This paper discusses the radiometric data for the Brusque Belt (SC) where Rb-Sr isochrons, U-Pb in zircons, K-Ar in minerals and whole rock Sm-Nd model ages are available. The analysis of these results reveals two main groups, without intermediate values. The first, 500 to 800Ma., is related to magmatic and metamorphic ages and the second, 1600-2000Ma begin with the (probably) sedimentation age. A monociclic evolution is proposed, but with uncertanties in the age of the first metamorphic phase. (author)

Analysis of tensile strain enhancement in Ge nano-belts on an insulator surrounded by dielectrics

International Nuclear Information System (INIS)

Lu Wei-Fang; Li Cheng; Huang Shi-Hao; Lin Guang-Yang; Wang Chen; Yan Guang-Ming; Huang Wei; Lai Hong-Kai; Chen Song-Yan

2013-01-01

Ge nano-belts with large tensile strain are considered as one of the promising materials for high carrier mobility metal—oxide—semiconductor transistors and efficient photonic devices. In this paper, we design the Ge nano-belts on an insulator surrounded by Si 3 N 4 or SiO 2 for improving their tensile strain and simulate the strain profiles by using the finite difference time domain (FDTD) method. The width and thickness parameters of Ge nano-belts on an insulator, which have great effects on the strain profile, are optimized. A large uniaxial tensile strain of 1.16% in 50-nm width and 12-nm thickness Ge nano-belts with the sidewalls protected by Si 3 N 4 is achieved after thermal treatments, which would significantly tailor the band gap structures of Ge-nanobelts to realize the high performance devices. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Precipitated Fluxes of Radiation Belt Electrons via Injection of Whistler-Mode Waves

Science.gov (United States)

Kulkarni, P.; Inan, U. S.; Bell, T. F.

2005-12-01

Inan et al. (U.S. Inan et al., Controlled precipitation of radiation belt electrons, Journal of Geophysical Research-Space Physics, 108 (A5), 1186, doi: 10.1029/2002JA009580, 2003.) suggested that the lifetime of energetic (a few MeV) electrons in the inner radiation belts may be moderated by in situ injection of whistler mode waves at frequencies of a few kHz. We use the Stanford 2D VLF raytracing program (along with an accurate estimation of the path-integrated Landau damping based on data from the HYDRA instrument on the POLAR spacecraft) to determine the distribution of wave energy throughout the inner radiation belts as a function of injection point, wave frequency and injection wave normal angle. To determine the total wave power injected and its initial distribution in k-space (i.e., wave-normal angle), we apply the formulation of Wang and Bell ( T.N.C. Wang and T.F. Bell, Radiation resistance of a short dipole immersed in a cold magnetoionic medium, Radio Science, 4 (2), 167-177, February 1969) for an electric dipole antenna placed at a variety of locations throughout the inner radiation belts. For many wave frequencies and wave normal angles the results establish that most of the radiated power is concentrated in waves whose wave normals are located near the resonance cone. The combined use of the radiation pattern and ray-tracing including Landau damping allows us to make quantitative estimates of the magnetospheric distribution of wave power density for different source injection points. We use these results to estimate the number of individual space-based transmitters needed to significantly impact the lifetimes of energetic electrons in the inner radiation belts. Using the wave power distribution, we finally determine the energetic electron pitch angle scattering and the precipitated flux signatures that would be detected.

Problems with models of the radiation belts

International Nuclear Information System (INIS)

Daly, E.J.; Lemaire, J.; Heynderickx, D.; Rodgers, D.J.

1996-01-01

The current standard models of the radiation-belt environment have many shortcomings, not the least of which is their extreme age. Most of the data used for them were acquired in the 1960's and early 1970's. Problems with the present models, and the ways in which data from more recent missions are being or can be used to create new models with improved functionality, are described. The phenomenology of the radiation belts, the effects on space systems, and geomagnetic coordinates and modeling are discussed. Errors found in present models, their functional limitations, and problems with their implementation and use are detailed. New modeling must address problems at low altitudes with the south Atlantic anomaly, east-west asymmetries and solar cycle variations and at high altitudes with the highly dynamic electron environment. The important issues in space environment modeling from the point of view of usability and relationship with effects evaluation are presented. New sources of data are discussed. Future requirements in the data, models, and analysis tools areas are presented

Nonlinear Scattering of VLF Waves in the Radiation Belts

Science.gov (United States)

Crabtree, Chris; Rudakov, Leonid; Ganguli, Guru; Mithaiwala, Manish

2014-10-01

Electromagnetic VLF waves, such as whistler mode waves, control the lifetime of trapped electrons in the radiation belts by pitch-angle scattering. Since the pitch-angle scattering rate is a strong function of the wave properties, a solid understanding of VLF wave sources and propagation in the magnetosphere is critical to accurately calculate electron lifetimes. Nonlinear scattering (Nonlinear Landau Damping) is a mechanism that can strongly alter VLF wave propagation [Ganguli et al. 2010], primarily by altering the direction of propagation, and has not been accounted for in previous models of radiation belt dynamics. Laboratory results have confirmed the dramatic change in propagation direction when the pump wave has sufficient amplitude to exceed the nonlinear threshold [Tejero et al. 2014]. Recent results show that the threshold for nonlinear scattering can often be met by naturally occurring VLF waves in the magnetosphere, with wave magnetic fields of the order of 50-100 pT inside the plasmapause. Nonlinear scattering can then dramatically alter the macroscopic dynamics of waves in the radiation belts leading to the formation of a long-lasting wave-cavity [Crabtree et al. 2012] and, when amplification is present, a multi-pass amplifier [Ganguli et al. 2012]. By considering these effects, the lifetimes of electrons can be dramatically reduced. This work is supported by the Naval Research Laboratory base program.

The size of the auroral belt during magnetic storms

Directory of Open Access Journals (Sweden)

N. Yokoyama

1998-05-01

Full Text Available Using the auroral boundary index derived from DMSP electron precipitation data and the Dst index, changes in the size of the auroral belt during magnetic storms are studied. It is found that the equatorward boundary of the belt at midnight expands equatorward, reaching its lowest latitude about one hour before Dst peaks. This time lag depends very little on storm intensity. It is also shown that during magnetic storms, the energy of the ring current quantified with Dst increases in proportion to Le–3, where Le is the L-value corresponding to the equatorward boundary of the auroral belt designated by the auroral boundary index. This means that the ring current energy is proportional to the ion energy obtained from the earthward shift of the plasma sheet under the conservation of the first adiabatic invariant. The ring current energy is also proportional to Emag, the total magnetic field energy contained in the spherical shell bounded by Le and Leq, where Leq corresponds to the quiet-time location of the auroral precipitation boundary. The ratio of the ring current energy ER to the dipole energy Emag is typically 10%. The ring current leads to magnetosphere inflation as a result of an increase in the equivalent dipole moment.Key words. Ionosphere (Auroral ionosphere · Magnetospheric physics (Auroral phenomena; storms and substorms

Explaining the Diverse Response of the Ultra-relativistic Van Allen Radiation Belt to Solar Wind Forcing

Science.gov (United States)

Mann, I. R.; Ozeke, L.; Murphy, K. R.; Claudepierre, S. G.; Rae, J.; Milling, D. K.; Kale, A.; Baker, D. N.