Effect of heterogeneous distribution of crosslink density on physical properties of radiation vulcanized NR (Natural Rubber) latex film

International Nuclear Information System (INIS)

Keizo Makuuchi; Fumio Yoshii; Miura, H.; Murakami, K.

1996-01-01

Thus a study has been carried out to investigate the effect of particle to particle variation in crosslink density on physical properties of radiation vulcanized NR latex film. NR latex was irradiated in small bottle by γ rays without vulcanization accelerator to provide latex rubber particles having homogeneous distribution of crosslink density. The doses were 30, 50, 100, 250, 300, 400, 500 and 600 kGy. Weight swelling ratio, gel fraction, tensile strength and elongation at break of the latex film from the mixed latex were measured. The vulcanization dose of this latex was 250 kGy. Then the two different latexes were mixed in a such way to adjust the average dose of 250 kGy to prepare a latex consisting of rubber particles having heterogeneous distribution of crosslink density. Tensile strength of the latex film was depressed by mixing. The reduction increased with increasing the decrease of gel fraction by mixing. However the reduction was not serious when the dose difference of two latexes was less than 200 kGy

Aspects of Degradability and Aging of Natural Rubber Latex Films Obtained by Induced Ionizing Radiation Processes of Latex Vulcanization

International Nuclear Information System (INIS)

Parra, D. F.

2006-01-01

This study refers to the degradability of NRLF, natural rubber latex films, obtained by ionizing radiation. Three types of NRLF were prepared: irradiated latex, irradiated latex with about 1% of soy lecithin and sulfur-vulcanized latex, by cold vulcanization process. The films were buried in vases of two different kinds of soil: common soil and common soil with earthworm humus. Fast aging tests in laboratory with exposition to ultraviolet rays were done in irradiated latex films and irradiated latex films with soy lecithin. The results obtained after ten months of tests with buried films agree with the results of the fast aging tests, showing singularities of each type of soil and each kind of latex process. It also shows how weather inclemency can induce the films degradation process. The sulfur-vulcanized films were weakly degraded when buried. The films with lecithin and buried in vase with only common soil showed the biggest mass loss, but the films with lecithin buried in vases with common earthworm humus and soil increased their weigh and dimensions due to fungi formation. The irradiated latex films are more degradable then the sulfur-vulcanized films. The irradiated latex film, unlike the sulfur vulcanized film, showed high fungi colonization when buried. We conclude that the irradiated latex films are more easily biodegradable than the sulfur vulcanized latex films. The biodegradability increases with the addition of small amounts of soy lecithin (∼1%). The mechanical resistance of the buried films decreased related to the non-buried ones, proving that the outdoor aging in soil and the presence of fungi in the films can modify the mechanical properties of the irradiated latex owing to the biodegradation

Radiation vulcanization of natural rubber latex with low energy accelerator

Energy Technology Data Exchange (ETDEWEB)

Haque, Emdadul; Makuuchi, Keizo; Ikeda, Kenichi; Yoshii, Fumio; Kume Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Mitomo, Hiroshi [Gunma Univ., Faculty of Engineering, Department of Biological and Chemical Engineering, Kiryu, Gunma (Japan)

2001-03-01

The radiation vulcanization of natural rubber latex (RVNRL) with the recently installed electron beam (EB) pilot plant at Takasaki Radiation Chemistry Research Establishment, Takasaki, Japan has been discussed. The accelerating voltage and beam current of the plant are 250 kV and 10 mA respectively. The plant has a reaction vessel with the capacity of 18 liters latex to irradiate at a time. In order to obtain a suitable setting of experimental for RVNRL under EB of the plant the parameters such as irradiation time, defoamer concentration, volume of latex, beam current etc. are being optimized by varying the individual parameter at a constant set of the other variables. (author)

Surgical gloves fabrication using natural rubber latex vulcanized with gamma radiation

International Nuclear Information System (INIS)

Collantes, Hugo David Chirinos.

1995-01-01

Surgical gloves were manufactured by immersion coagulant method from vulcanized natural rubber latex by gamma rays at dose of 10 kGy in the air, at room temperature, using the following sensitizer vulcanization An-B 3 phr/KOH 0.2 phr. The influence of the parameter in the thickness of the surgical gloves manufacture, studied through fractional factorial designs technic, can be resumed by empirical linear correlation: y = 0.213 + 0.025 [Ca Cl 2 ] + 0.019 t. (author). 49 refs., 13 figs., 31 tabs

Toxicological evaluation of natural rubber latex film vulcanized with ionizing radiation

International Nuclear Information System (INIS)

Campos, Vania E.; Higa, Olga Z.; Guedes, Selma M.L.; Hanada, Seico

1999-01-01

The industrial vulcanization of natural rubber latex (NRL) is made worldwide by conventional process using sulphur, but it can be made by an alternative process using ionizing radiation. The main advantages of this process are related to absence of toxic effect promoted by chemical substances added to the NRL on the conventional process. In this research was tested the toxicological properties of the films vulcanized by the alternative process in relation to that vulcanized by the conventional process. The toxicity was evaluated by in vitro cytotoxicity assay and in vivo systemic toxicity assay. The results showed that vulcanized films by gamma ray are less cytotoxic. The systemic toxicity assay showed that only the vulcanized film using sulphur induced allaying and motor in coordination on the animals for a short period of time. these results evidence the less cytotoxic properties of vulcanized films by gamma ray in relation to that vulcanized by conventional process using sulphur. (author)

Biodegradability and aging study of rubber films obtained by gamma radiation vulcanization processes of latex

International Nuclear Information System (INIS)

Martins, Carlos Felipe Pinto

2005-01-01

The natural rubber latex (NRL) is industrially crosslinked by the conventional process of vulcanization, which uses sulphur and heat. Otherwise, the network can also be done by the alternative process with ionizing radiation. In this work the crosslinking of NRL was studied by the comparison of the conventional vulcanization system and the ionizing radiation process of 60 C source. The products obtained, the irradiated latex, the irradiated latex with approximately 1% of soy lecithin and the sulphur vulcanized latex were tested by accelerated aging with ultraviolet (UV) and outdoor aging with compostage, tensile strength at break, swelling and gel fraction, fungi micro biota, scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and thermogravimetry and differential scanning calorimetry analysis (TG and DSC). The results showed that the aging with microorganisms have a great influence in the physical properties of the samples. The thermal stability order observed showed that the sulphur vulcanized latex is more resistant, what is probably associated to a network more stable under the aging conditions. On the other hand, the irradiated latex showed intense biodegradation aspects, particularly with the presence of the soy lecithin. (author)

Extractable protein of radiation vulcanized natural rubber latex

International Nuclear Information System (INIS)

Soebianto, Y.S.; Upul, R.M.; Makuuchi, K.; Yoshii, F.; Kume, T.

2000-01-01

A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) as much as 3 phr in three different processes: added to RVNRL, added to re-centrifuged RVNRL, and added to RVNRL followed by centrifugation. The protein content was determined by enhanced BCA method, and identified by SDS-PAGE analysis. Addition of WSP followed by centrifugation reduces EP up to the minimum protein detection, and shortens the leaching time to 20-30 min. SDS-PAGE analysis confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The molecular weight of WSP dictates the efficiency of protein removal. (author)

Extractable protein of radiation vulcanized natural rubber latex

Energy Technology Data Exchange (ETDEWEB)

Soebianto, Y.S. [Center for Research and Development of Isotopes and Radiation Technology, BATAN, Jakarta (Indonesia); Upul, R.M. [Rubber Research Institute of Sri Lanka, Ratmalana (Sri Lanka); Makuuchi, K.; Yoshii, F.; Kume, T. [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

2000-03-01

A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) as much as 3 phr in three different processes: added to RVNRL, added to re-centrifuged RVNRL, and added to RVNRL followed by centrifugation. The protein content was determined by enhanced BCA method, and identified by SDS-PAGE analysis. Addition of WSP followed by centrifugation reduces EP up to the minimum protein detection, and shortens the leaching time to 20-30 min. SDS-PAGE analysis confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The molecular weight of WSP dictates the efficiency of protein removal. (author)

Radiation Vulcanization of Natural Rubber Latex (RVNRL): A Potential Material for Nuclear Power Plant Gloves

International Nuclear Information System (INIS)

Pairu Ibrahim; Wan Manshol Wan Zain; Keong, C.C.; Mohd Noorwadi Mat Lazim

2011-01-01

Radiation vulcanization of natural rubber latex has great potential for the production of nuclear power plant gloves due to its low ash and mineral content. And this is in-line with the role played by Malaysian Nuclear Agency as Technical Supporting Organization for Nuclear Power Program. This paper discussed the evaluation done to determine ash content in RVNRL and SVNRL films. Both samples were prepared using casting technique and the properties were compared. Films prepared from raw latex without any vulcanizing agent were regarded as a control. (author)

Extractable proteins from field radiation vulcanized natural rubber latex

Energy Technology Data Exchange (ETDEWEB)

Parra, Duclerc F. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil)]. E-mail: dfparra@ipen.br; Pinto Martins, Carlos Felipe [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil); Collantes, Hugo D.C. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil); Lugao, Ademar B. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil)

2005-07-01

The type I allergy associated with the use of natural rubber latex (NRL) products is caused by the NRL proteins leached by the sweat or other body fluids. Makuuchi's group proposed for the first time the proteins removal by the addition of water-soluble polymers (WSP) on radiation vulcanization of natural rubber latex (RVNRL) that is a promising process under development in many countries. In this study, Brazilian field natural rubber was irradiated with a {sup 60}Co gamma source to reduce the content of WSP in the final product. WSP was used as additive to improve the extraction of protein. After irradiation the RVNRL was centrifuged to extract the WSP and proteins. The analytical methodology for protein content was based on the modified Lowry method according to ASTM D5712. Protein determination was carried out in serum of latex and in the extracts of the gloves. The concentration of extractable water-soluble proteins in serum of irradiated field NRL (NRL1), not irradiated one (NRL2); of twice centrifuged sample with polymer additive NRL (NRL3) and of the glove manufactured (NRLG) are compared with commercial glove (CG). The irradiation process increases the extractable water-soluble proteins, EP, as reported in the literature. In this study the use of polymeric additive on the bi-centrifugation process to remove protein was successful and the EP of the glove obtained in NRL3 was at around 40% of the commercial glove.

Development of rubber gloves by radiation vulcanization

International Nuclear Information System (INIS)

Makuuchi, K.; Yoshii, F.; Ishigaki, I.; Mogi, M.; Saito, T.

1990-01-01

The processes of radiation vulcanization and production of protective rubber gloves for radioactive contamination are described. A newly developed sensitizing system consisting of 5 phr 2-ethylhexyl acrylate and 1 phr carbon tetrachloride was used to vulcanize natural rubber latex at 12 kGy. Transparent and soft gloves were obtained from the radiation vulcanized latex by a coagulant dipping process. The mechanical properties of the gloves meet Japanese Industrial Standard specification for protective gloves. Combustion analysis of the gloves revealed that the amount of evolved sulfur dioxide and remaining ashes are less than those from commercially available rubber gloves. A trial usage of the gloves at a nuclear power plant showed that the gloves were easy to use for delicate work without undergoing fatigue. (author)

Efficiency of 1,9- Nonane-diol-diacrylate as a radiation vulcanization accelerator for natural rubber latex

International Nuclear Information System (INIS)

Haque, M.E.

2003-09-01

The efficiency of 1,9- Nonane-diol-diacrylate (NDDA) as a radiation vulcanization accelerator (RVA) for natural rubber latex (NRL) was investigated. Both gamma rays and electron beam (EB) were used for vulcanizing NRL with NDDA. The radiation dose of gamma rays, concentration of NDDA required to vulcanize the latex were optimized. 20 kGy radiation dose of gamma rays and 5 phr concentration of NDDA were found optimum to get maximum tensile and related properties. NRL was vulcanized under EB to find out the optimum condition of irradiation with this RVA. The defoamer concentrations, length of irradiation time under EB, concentration of RVA were optimizer by changing various parameters of the EB machine with a constant set of the others. 0.2 phr defoamer concentration, 30 minutes irradiation time and 5 phr concentration of NDDA were found optimum for irradiation of NRL under the EB machine. Effect of low current and optimum volume of latex charged in the reaction vessel suitable for vulcanization at a time were found out. (author)

Effect of Antioxidants on Radiation Vulcanization Natural Rubber Latex (RVNRL) Film

International Nuclear Information System (INIS)

Syuhada Ramli; Sofian Ibrahim; Muhammad Saiful Omar

2015-01-01

This paper presents the results on the effects of different antioxidants used in Radiation Vulcanization Natural Rubber Latex (RVNRL)) films between 0 to 10 weeks monitoring. Antioxidants used for the RVNRL formulation were Aquanox LP, Irganox and Wingstay L. Color difference evaluation by using Chroma Meter CR-400 found that RVNRL film with Irganox was the most stained yellowish after 8 weeks monitoring. Tensile strength for RVNRL with Aquanox found achieved the optimum strength between 25.4 to 27.13 mPa. The scanner electron microscopic (SEM) indicated more Aquanox molecules to penetrate and interact with the rubber molecule, thus becoming more effective inhibitor against its oxidative ageing. (author)

The influence of radiolytic sensitizers in natural rubber latex vulcanization induced by ionizing radiation

International Nuclear Information System (INIS)

Guedes, S.M.L.; Souza, A. de

1991-01-01

This work made on radiation vulcanization of natural rubber latex process by gamma rays from 60 Co source and electron beam of 1.5 MeV, 25 m A by Dynamitron, instead of classic process using sulfur. The experiment was carried out to study the influence of sensitizers (C Cl 4 and n-butyl acrylate) and was reported the vulcanization dose for each sensitizers, related to maximum tensile strength. The results show the possibility to introduce the volatile sensitizer (n-butyl acrylate) instead of C Cl 4 (toxic) in industry applications. (author)

Study on preparation of new antioxidants for radiation vulcanized natural rubber latex product. Antioxidant from keratin

International Nuclear Information System (INIS)

Nguyen Quoc Hien; Nguyen Van Toan; Vo Tan Thien; Le Hai

2000-01-01

The thermo-oxidative aging resistance of radiation vulcanization of natural rubber latex (RVNRL) products should be adequately by using suitable antioxidants or new kind of effective antioxidant. This work presents the results of preparation of natural antioxidant from hair keratin. Characteristics and effectiveness of resultant antioxidant are also presented. The results obtained indicates that antioxidant made from hair keratin is safe and effective for rubber products from RVNRL. (author)

Pilot scale experiments on radiation vulcanization of NR latex

Science.gov (United States)

Ridwan, M.

The potential of irradiated latex as raw material of commercial use is under testing on pilot plant scale in Indonesia which has 225 kCi Co-60 irradiation facility and can irradiate 1000 tonnes of centrifuged latex per annum. The facility was jointly designed by BATAN of Indonesia and JAERI of Japan and was jointly financed by UNDP/IAEA, Government of Japan and Government of Indonesia under UNDP/IAEA Regional Cooperative Agreement Project on Industrial Application of Isotopes and Radiation Technology. The facility is a water pool type and can accomodate 400 kCi Co-60. The Co-60 rack has two shapes, plate and cylindrical shapes. The plate shape source is used for natural rubber latex irradiation and the cylindrical one is used for other irradiation services. The vulcanization system consists of three major components : emulsification unit ( height : 650 mm, diameter 500 mm ), mixing unit ( height : 1900mm, diameter 1200 mm ) and vulcanization reactor ( height : 1800 mm, diameter 1300 mm ). The first two components are located outside shielded room while the third one-in irradiation room. The radiation vulcanization process is a much simpler energy saving process comparedto the conventional thermal process which has two vulcanization steps before and after dipping. The physical and mechanical properties of irradiated NR Latex are comparable to those of sulfur vulcanized, and depend on many factors such as irradiation dose, sensitizer content, dry rubber content and storage time.

The effect of proteins on the aging properties of radiation vulcanized natural rubber latex

International Nuclear Information System (INIS)

Abad, L.V.

1993-01-01

The effect of natural rubber latex (NRL) proteins on the aging properties of NRL films was investigated. SDS-PAGE electrophoresis of the rubber proteins in NRL (Sri-Lanka) indicated a total of 18 proteins. A sharp decrease in tensile strength was observed after aging when NRL films were leached in 1% NH 4 OH. However, when these films were soaked in ethanol prior to leaching, the aging properties approximated those of the unleashed samples. Electrophoretic analysis of the proteins present in the NH 3 extracts of leached RVNRL films showed a high concentration of the protein herein. This protein was not found in the NH 3 extracts of ethanol soaked films. NRL proteins were shown to decelerate the aging process of Radiation Vulcanized Natural Rubber Latex (RVNRL) films. Among the proteins, herein exhibited good anti-aging properties. The hydrolyzates from NR proteins also enhanced considerably the aging properties of RVNRL. (auth.). 8 refs.; 40 figs.; 30 tabs

Pilot scale experiments on radiation vulcanization of NR latex

International Nuclear Information System (INIS)

Ridwan, M.

1985-01-01

The potential of irradiated latex as raw material of commercial use is under testing on pilot plant scale in Indonesia which has 225 kCi Co-60 irradiation facility and can irradiate 1000 tonnes of centrifuged latex per annum. The facility was jointly designed by BATAN of Indonesia and JAERI of Japan and was jointly financed by UNDP/IAEA, Government of Japan and Government of Indonesia under UNDP/IAEA Regional Cooperative Agreement Project on Industrial Application of Isotopes and Radiation Technology. The facility is a water pool type and can accommodate 400 kCi Co-60. The Co-60 rack has two shapes, plate and cylindrical shapes. The plate shape source is used for natural rubber latex irradiation and the cylindrical one is used for other irradiation services. The vulcanization system consists of three major components: emulsification unit, mixing unit and vulcanization reactor. The first two components are located outside shielded room while the third one in irradiation room. The radiation vulcanization process is a much simpler energy saving process compared to the conventional thermal process which has two vulcanization steps before and after dipping. The physical and mechanical properties of irradiated NR latex are comparable to those of sulfur vulcanized. (author)

Production Of Hollow Toy Product From Radiation Pre vulcanized Natural Rubber Latex (RVNRL) By Using Casting And Moulding Technique

International Nuclear Information System (INIS)

Mohd Noorwadi Mat Lazim; Sofian Ibrahim; Muhammad Saiful Omar

2013-01-01

Hollow toy products are very synonym to the child from the age of months since it able to stimulating each of their sense such as sight, hearing, taste, touch and smell. Most of hollow toy products are made from natural rubber latex by using moulding and casting technique. The moulding and casting technique is a manufacturing process by pored liquid latex into a mould, which contain cavity of the desired shape. The mould made from plaster of Paris able to absorbs water from latex meanwhile the presence of calcium ions from plaster of Paris will tend to diffuse into latex thus promote formation of deposit on surface of cavity mould. To improve the quality and safety of hollow toy product made from latex, Radiation Pre vulcanized Natural Rubber Latex (RVNRL) has been identified to be used because it can fulfill the standard requirement for latex and also due to its special abilities such as lower modulus (soft latex products), nitrosamines free, low in nitrosatables, free from chemical accelerators induced allergies and better biodegradability. This paper identify the problem appears from the process of making hollow toy products from RVNRL by using moulding and casting technique. (author)

n-BA/KOH/t-BHP behaviour in the natural rubber latex vulcanization by gamma rays

International Nuclear Information System (INIS)

Souza, A. de.

1994-01-01

Natural rubber latex was vulcanized in the absence and in the presence of sensitizer (S), with gamma ray from 60 Co source, panoramic type, at the dose rate range of 1,20-1,33 kGy/h. The components of used S were n-butyl acrylate (n-BA), the KOH as stabilizer and t-butyl hydroperoxide (t-BHP) as co-S. The purpose of this work was to study the efficiency and the behaviour of each component of S in the irradiated latex crosslinking by tensile strength (T b ), volume fraction and permanent set. In the absence of S occur straight crosslinking between macromolecular adjacent radicals. IN the presence of S, the n-BA participates in the crosslinking through acrylic bridges between macromolecules. (author)

Cost evaluation of radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Makuuchi, K.

2003-01-01

Cost of radiation vulcanized NR latex was evaluated. The plant would be built in an existing dipping factory in an industrial area in a Southeast Asian country. One thousands dry tons of NR latex are vulcanized with a low energy electron accelerator. The electron accelerator is a self-shielding low energy type. The maximum accelerating voltage is 300 kV and the output power is 10 kW. The total construction cost of the plant is $400,000 including electron accelerator and other equipments. Costs of raw materials and utilities are $1.165 and $0.023 per one kg of product, respectively. The fixed costs of the plant consist of labor costs, labor overhead, maintenance, plant overhead, depreciation, and bank interest. It is $0.190/kg of product. The company overhead for operation including company management, R and D and insurance is $0.044/kg of product. Thus, the total production cost is estimated to be $1.422/kg of product. (author)

A study of using polythiol compounds and 2-ethyl-hexyl-acrylate with carbon tetrachloride as sensitizers for radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Polsuksiri, C.

1989-01-01

Experiments on using 3 different compounds of polythiol and an acrylate as sensitizer for radiation vulcanization were conducted. It was found that 1,4 butane diol propane tris-3-mercapto propionate showed the tendency to be a good sensitizer. The tensile strength of the rubber film prepared from the irradiated latex was found to be 14 MPa at sensitizer concentration of 1 phr and radiation dose of 45 kGy. As for 2-ethyl hexyl acrylate (2EHA), the maximum tensile strength of rubber film was found to be 23 MPa at concentration of 3 phr and radiation dose of 35 kGy. The mixture of 2 EHA and CCl 4 at various ratio was also used as sensitizer. The optimum ratio was found to be 5:1 at concentration of 6 phr and radiation dose of 15 kGy. The maximum tensile strength was as high as 25 MPa. The study also revealed that the radiation vulcanized latex with crosslink density of about 18x10 18 C.L./cm 3 would give the rubber film of highest tensile strength

Radiation response of Philippine natural rubber latex

International Nuclear Information System (INIS)

Dela Rosa, A.M.; Abad, L.V.; Ana-Relleve, L.S.; Tranquilan-Aranilla, C.; Pascual, C.L.

1998-01-01

Our earlier work has shown that the natural rubber latex (NRL) produced and processed in the Philippines is suited for radiation vulcanization. The cast films from NRL with 50% TSC exhibited maximum tensile strengths of 25-32 MPa at 15 kGy, which is the vulcanization dose or Dv. In the manufacture of dipped NRL products, certain specifications such as %TSC, protein content and tensile properties, must be met to ensure an acceptable product. For radiation vulcanization of natural rubber latex (RVNRL) to be accepted as an alternative process, it must also meet the requirements. Thus, this paper presents additional data on the radiation response of local NRL at different total solids contents (TSC), leachable proteins from NRL films as a function of dose, and the thermal activities of irradiated natural rubber latex (INRL). Different formulations of NRL showed varying tolerances to nBA. Data showed that as %TSC increases, the maximum concentration of nBA that can be added without affecting the stability of the latex decreases. The Dv increases as the %TSC increases and the nBA content decreases. This difference in response may be attributed to a lower concentration of nBA in formulations with higher %TSC. These data indicate that the parameters in the radiation treatment will be dictated by the intended applications of INRL. The thermogravimetric data showed greater stability of INRL to thermal oxidation relative to the unirradiated NRL, which correlates directly with the tensile properties of the INRL. A radiation dose of 10 kGy increased the amount of proteins leached from cast latex films. The amount of extractable proteins did not increase significantly at higher doses. The SDS PAGE analysis of the extractable proteins from unirradiated latex film showed distinct bands. An additional band at 60 Kda appeared at 10 kGy. All these bands became diffuse at higher doses, indicating the radiolysis of the proteins

Biodegradability and aging study of rubber films obtained by gamma radiation vulcanization processes of latex; Estudo da biodegradabilidade e envelhecimento de filmes de borracha obtidos por processos de vulcanizacao do latex por radiacao induzida de fonte gama

Energy Technology Data Exchange (ETDEWEB)

Martins, Carlos Felipe Pinto

2005-07-01

The natural rubber latex (NRL) is industrially crosslinked by the conventional process of vulcanization, which uses sulphur and heat. Otherwise, the network can also be done by the alternative process with ionizing radiation. In this work the crosslinking of NRL was studied by the comparison of the conventional vulcanization system and the ionizing radiation process of {sup 60}C source. The products obtained, the irradiated latex, the irradiated latex with approximately 1% of soy lecithin and the sulphur vulcanized latex were tested by accelerated aging with ultraviolet (UV) and outdoor aging with compostage, tensile strength at break, swelling and gel fraction, fungi micro biota, scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and thermogravimetry and differential scanning calorimetry analysis (TG and DSC). The results showed that the aging with microorganisms have a great influence in the physical properties of the samples. The thermal stability order observed showed that the sulphur vulcanized latex is more resistant, what is probably associated to a network more stable under the aging conditions. On the other hand, the irradiated latex showed intense biodegradation aspects, particularly with the presence of the soy lecithin. (author)

Effect of gamma radiation dose and sensitizer on the physical properties of irradiated natural rubber latex

International Nuclear Information System (INIS)

Komgrit, R.; Thawat, C.; B, Tripob; Wirach, T.

2009-07-01

Full text: The vulcanization of natural rubber latex can be induced by gamma radiation, which enhances cross-linking within the rubber matrix. The purpose of this research is to investigate the effect of gamma radiation dose and sensitizers on the physical properties of irradiated natural rubber. Three sensitizers n-butyl acrylate (n-B A), tetrachloroethylene (C 2 Cl 4 ) and trichloromethane (CHCl 3 ) were mixed with natural rubber latex before irradiation with gamma ray dose varied from 14 to 22 kGy. Results showed that the mixture of three sensitizers with specific ratios effectively induced the cross-linking of natural rubber latex. The cross-linking ratio and improved physical properties increased with increasing gamma dose. Therefore, the mixture ratios of n-B A, C 2 Cl 4 and CHCl 3 have shown to be a critical parameter in the vulcanization of natural rubber latex by gamma radiation

Thermal-kinetic study of natural rubber latex films vulcanized by using gamma radiation; Estudo termo-cinetico de filmes de latex de borracha natural de Hevea brasiliensis vulcanizada por radiacao gama

Energy Technology Data Exchange (ETDEWEB)

Leal, Ana Paula Pinho Rodrigues; Barros, Glaucione Gomes de [Brasilia Univ., DF (Brazil). Inst. de Quimica; Guedes, Selma M.L. [Instituto de Pesquisa em Energia Nuclear, Sao Paulo, SP (Brazil)

1999-07-01

Vulcanization of natural rubber latex by ionization radiation produces the crosslink in disperse latex particles. Advantages over conventional process of vulcanization are: the absence of carcinogenic nitrosamines, low cytotoxicity and better degradation at room conditions, due to mainly to the absence of sulfur, zinc oxide and dithiocarbamates. Thermogravimetric analysis (TG) is the measurement of the weight change of a material as a function of temperature and time. TG data different heat speed provide an alternative model of the kinetics of degradation of polymeric materials. The kinetic studies of this material showed a single degradation process at least for 76,5% of mass loss. The activation energy was 49 Kcal/mol. For higher mass loss (85%) the degradation was characterized by associate mechanism. (author)

The role of proteins on the thermal oxidative aging of radiation vulcanized natural rubber latex

International Nuclear Information System (INIS)

Abad, L.V.; Rosa, A. de la; Keizo Makuuchi; Fumio Yoshii

1996-01-01

The effect of Hevea latex proteins on the aging properties of radiation vulcanized natural rubber latex (RVNRL) was investigated. Unpurified RVNRL films exhibited better aging properties than the purified RVNRL films. A sharp decrease in tensile strength was observed after aging when RVNRL films were leached in 1% NH sub 4 OH. However, when these films were soaked in ethanol prior to leaching, the aging properties approximated those of the unleached samples. Kjeldahl and FT-IR analyses of the leached and unleached RVNRL films indicated a higher protein content for both the unleached and ethanol-soaked films than for leached films. Electrophoretic analysis of the proteins present in the NH, extracts of leached RVNRL films showed a high concentration of hevein. This protein was not found in the ATH, extracts of ethanol soaked films. Hevein was shown to improve the aging properties of RVNRL

Toxicological evaluation of natural rubber films from vulcanized latex by the conventional process and the alternative process with ionizing radiation

International Nuclear Information System (INIS)

Campos, Vania Elisabeth

1997-01-01

The industrial vulcanization of natural rubber latex (NRL) is made all over the world by conventional process using sulphur and heat but it can be made by an alternative process using ionizing radiation. In this research the NRL was tested by 13 physical, chemical and mechanical assays which showed its good quality. It was done a preliminary study of the toxicological properties of 4 natural rubber films obtained by casting process of NRL: one non vulcanized, other vulcanized by the conventional process and two vulcanized by the alternative process. In the alternative process the films were obtained by irradiation of NRL by gamma rays from the 60 Co source at 250 kGy in the absence of sensitizer and irradiated NRL at 12 kGy in the presence of 4ph r of n-butyl acrylate / 0.2 phr of KOH. These vulcanization doses were determined from broken tensile strength. In the conventional process, sulphur vulcanized NRL was made using a classical composition. Another film was made with non vulcanized NRL. The preliminary evaluation of the toxicological properties was made from in vitro cytotoxicity and in vivo systemic toxicity assays. The LBN films vulcanized by the alternative process have less cytotoxicity than the NRL film vulcanized by the conventional process. The sensitized vulcanized films by gamma rays and non vulcanized films showed similar cytotoxicity while the vulcanized films without sensitizer showed a slight lower cytotoxicity. The non vulcanized NRL film and the NRL films vulcanized by the alternative process did not show toxic effects int he 72 hours period of the systemic toxicity assay. However the NRL film vulcanized with sulphur induced effects like allaying and motor in coordination on the animals treated with an oil extract at the fourth hour and recovering after that. The alternative process promoted lower toxic effects than conventional process because there was no toxic substances present. (author)

Extraction and comparison of proteins from natural rubber latex by conventional and ionizing radiation methods

International Nuclear Information System (INIS)

Rogero, Sizue O.; Spencer, Patrick J.; Campos, Vania E.; Lusvarghi, Fabio M.; Higa, Olga Z.

1997-01-01

Several proteins in natural rubber latex (NRL) have been assigned to be significant allergens. It is known that proteins submitted to ionizing radiation suffer denaturation and immunochemical modification resulting in low antigenic reactivity. The aim of this study was to extract and compare water extractable proteins from NRL films vulcanized by conventional and by ionizing radiation methods. SDS-polyacrylamide gel electrophoresis (SDS--PAGE) and high pressure liquid chromatography (HPLC) showed a diffuse protein band of about 14 KDa, which we believe is rubber elongation factor (REF), in both eluates, but smaller in latex film vulcanized by ionizing radiation. REF has been suggested to be a major latex allergen. These data suggest that ionizing radiation vulcanization could be an useful method for the production of NRL goods with low antigenicity. (author). 8 refs., 2 figs., 1 tab

Effect of cellulose nanocrystals from corn cob with dispersion agent polyvinyl pyrrolidone in natural rubber latex film after aging treatment

Science.gov (United States)

Harahap, H.; Ridha, M.; Halimatuddahliana; Taslim; Iriany

2018-02-01

This study about the resistance of natural rubber latex films using nanocrystals cellulose filler from corn cob waste by aging treatment. Corn cob used as organic filler composed of cellulose, hemicellulose, and lignin. Each component has a potential for reuse, such as cellulose. Cellulose from corn cob has potential application as a filler prepared by hydrolysis process using a strong acid. The producing of natural rubber latex films through coagulant dowsing process. This research started with the pre-vulcanization process of natural rubber latex at 70 °C and followed by process of vulcanization at 110 °C for 20 minutes. Natural rubber latex films that have been produced continued with the aging treatment at 70 °C for 168 hours. The mechanical properties of natural rubber latex films after aging treatment are the tensile strength, elongation at break, M100 and M300 have performed.

Studied on Virgin Coconut Oil (VCO) and Olive Oil (OO) as an Alternative for Stabilizer of Radiation Vulcanized Natural Rubber Latex (RVNRL) Preparation

International Nuclear Information System (INIS)

Syuhada Ramli; Sofian Ibrahim; Mohd Noorwadi Mat Lazim

2016-01-01

This paper presents the effects of virgin coconut oil (VCO) and olive oil (OO) as an alternative stabilizer in the radiation vulcanized natural rubber latex (RVNRL). Potassium laurite (KL) as a stabilizer considered as a control of RVNRL sample were compared to mixed ratio 1:1 KL: VCO and 1:1 KL: OO stabilizer formulation. Total solid content (TSC) and tensile strength (TS) results showed no significant different between the formulations. Mechanical stability time (MST) indicates higher stability of RVNRL with addition of VCO. The fatty acid composition in VCO indicate VCO was acting well as stabilizer for latex stabilizer formulation. (author)

Preparation of irradiated natural rubber latex-styrene copolymer for electrical gloves

International Nuclear Information System (INIS)

Made Sumarti Kardha

2010-01-01

Research on irradiated natural rubber latex-styrene copolymer to prepare electrical glove have been done. Vulcanization of natural rubber latex (NRL) was done by mixing 2 phr (per hundred of rubber) of normal butyl acrylate (n-BA) emulsion then irradiated with ã-ray "6"0Co at the dose of 30 kGy producing irradiated natural rubber latex (INRL). Natural rubber latex-styrene copolymers (SC) were prepared by mixing NRL and styrene monomer at styrene concentrations of 50 phr, 75 phr, 100 phr, 500 phr and irradiated at the doses of 15 kGy, 30 kGy and 45 kGy, then characterized their latex and film properties to obtain optimum SC of SC50. This optimum SC, SC50 then mixed with IRNL at the weight ratio of 0/100, 30/70, 50/50, 70/30 and 100/0, to produce irradiated natural rubber latex-styrene copolymer. The properties of copolymer rubber films made by dipping process i.e., % conversion, total solid content, latex viscosity, tensile strength, modulus 300 %, elongation at break, electrical resistance and dielectric constant were then characterized. Characterization result showed that (INRL-SC50) with 50/50 ratio irradiated at the dose of 30 kGy, have % conversion of 80.93 %, electrical resistivity of 1.73 x 10"1"4 Ohm cm and dielectric constant of 2.76 which fulfill the requirement as material for electrical gloves. (author)

Hevea brasiliensis natural rubber latex film vulcanization by gamma radiation containing n-butyl acrylate: properties and morphology; Filme de latex de borracha natural de Hevea brasiliensis vulcanizado por radiacao gama contendo acrilato de n-butila: propriedades e morfologia

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Ana Paula Pinho; Barros, Glaucione Gomes de [Brasilia Univ., DF (Brazil). Dept. de Quimica; Guedes, Selma M.L. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

1997-07-01

Radiation vulcanization of natural rubber latex (RVNRL) in the presence of n-butyl acrylate (n-Ba) as sensitizer was carried out. The RVNRL films were investigated with respect to their thermal properties and morphology. The films presented two T{sub g} values obtained by DSC which were identified as due to linear and crosslinked domains. The thermal stability of the material was similar to that of linear material rubber. The morphology showed smooth regular surface characteristic of homogeneous phase domains. (author)

Extractable proteins from electron beam (EB) irradiated natural rubber (NR) latex

International Nuclear Information System (INIS)

Feroza Akhtar; Fumio Yoshii; Keizo Makuuchi

1996-01-01

The protein assay of natural rubber latex (NRL) vulcanized by low energy electron beam (EB, 300 keV, 30 mA) has been carried out using Bicinchoninic acid (BCA) reagent. Extractable protein in irradiated latex film was determined by measuring the absorption of colored solution at 562 nm using UV spectrometer. The effect of various radiation doses on the extractable protein content of NRL was investigated. It was ,found that the quantities of extractable protein increases with radiation dose. When compared with ,gamma-ray irradiated samples the same trend was observed. Electron beam irradiated latex films are leached in 1% (ammonia water for various lengths of time. From the results it was established that within 2 hours of leaching in ammonia water most of the extractable protein (96%) were removed from rubber film

A test trial irradiation of natural rubber latex on large scale for the production of examination gloves in a production scale

International Nuclear Information System (INIS)

Devendra, R.; Kulatunge, S.; Chandralal, H.N.K.K.; Kalyani, N.M.V.; Seneviratne, J.; Wellage, S.

1996-01-01

Radiation Vulcanization of natural rubber latex has been developed extensively through various research and development programme. During these investigations many data was collected and from these data it was proved that radiation vulcanized natural rubber latex (RVNRL) can be used as a new material for industry (RVNRL symposium 1989; Makuuchi IAEA report). This material has been extensively tested in making of dipped goods and extruded products. However these investigations were confined only to laboratory experiments and these experiments mainly reflected material properties of RVNRL and only a little was observed about its behavior in actual production scale operation. The present exercise was carried out mainly to study the behavior of the material in production scale by irradiating latex on a large scale and producing gloves in a production scale plant. It was found that RVNRL can be used in conventional glove plants without making major alteration to the plant. Quality of the gloves that were produced using RVNRL is acceptable. It was also found that the small deviation of vulcanization dose will affect the crosslinking density of films. This will drastically reduce the tensile strength of the film. Crosslinking density or pre-vulcanized relax modulus (PRM) at 100% is a reliable property to control the pre vulcanization of latex by radiation

Research and application of fuzzy subtractive clustering model on tensile strength of radiation vulcanization for nitrile-butadiene rubber

International Nuclear Information System (INIS)

Zuo Duwen; Wang Hong; Zhu Nankang

2010-01-01

By use of fuzzy subtractive clustering model, the relationship between tensile strength of radiation vulcanization of NBRL (Nitrile-butadiene rubber latex) and irradiation parameters have been investigated. The correlation coefficient was calculated to be 0.8222 in the comparison of experimental data to the predicted data. It was obvious that fuzzy model identification method is not only high precision with small computation, but also easy to be used. It can directly supply the evolution of tensile strength of NBR by fuzzy modeling method in radiation vulcanization process for nitrile-butadiene rubber. (authors)

Rubber/clay nanocomposites by combined latex compounding and melt mixing: A masterbatch process

International Nuclear Information System (INIS)

Tan, Jinghua; Wang, Xiaoping; Luo, Yuanfang; Jia, Demin

2012-01-01

Highlights: → Rubber/Ca-montmorillonite nanocomposites were prepared by the masterbatch process. → Latex compounding method is efficient to improve the Ca-montmorillonite dispersion. → Exfoliated structure was obtained in the masterbatch by latex compounding method. → Intercalated and exfoliated structures were achieved in the vulcanizate. → The properties of vulcanizate are improved by the addition of Ca-montmorillonite. -- Abstract: Rubber/Ca-montmorillonite (Ca-MMT) nanocomposites with well exfoliated Ca-MMT layers were prepared by combination of latex compounding and melt mixing. Firstly, a high Ca-MMT content masterbatch was co-coagulated by natural rubber (NR) latex and modified Ca-MMT aqueous suspension through latex compounding. The masterbatch was added in the system of styrene butadiene rubber (SBR) and epoxidized natural rubber (ENR) by melt mixing subsequently. The X-ray diffraction (XRD) and transmission electronic microscopy (TEM) results showed that intercalated and exfoliated nanocomposites were obtained by the masterbatch technique. The effects of modified Ca-MMT introduction into the rubber matrix, via the masterbatch technique, on the properties of the resulting composites were studied. It was found that the vulcanization was hindered by the incorporation of modified Ca-MMT, while mechanical performances, thermal stability and aging resistance were improved. The increasingly glass transition temperature and the storage modulus with the loading of modified Ca-MMT were measured by dynamic mechanical analysis (DMA).

Study on grafting of monomer onto natural rubber latex by radiation technique

International Nuclear Information System (INIS)

Nguyen Tan Man; Le Hai; Tran Thi Tam; Le Huu Tu, Pham Thi Sam; Dao Minh Phuong; Ha Thuc Huy

2004-01-01

Radiation vulcanization of natural rubber latex has been extensively developed through programmers assisted by the IAEA and UNDP under RCA in Asia and Pacific Region. R-D has been done in most of the Member States with technical assistance from Japan's Takasaki Radiation Chemistry Establishment. Radiation vulcanized natural rubber latex (RVNRL) has many advantages over the conventional sulfur vulcanized latex, such as absence of nitrosamine and low cytotoxicity. Radiation crosslinking is a room temperature process, itself an important cost advantage, it is easily controlled and desired extend of crosslinking is easily achieved by controlling the dose (irradiation time). Disadvantages of RVNRL to be improved are poor physical properties of film such as low tensile strength and tear strength. The research groups of Japan, Thailand and Indonesia concentrated on the improvement of physical properties of RVNRL using radiation grafted PMMA as additive [2]. F. Sundardi and W. Sofiarti have reported that tensile strength and hardness increased by radiation grafting of styrene onto NR [5]. Ono et al have reported the grafting of MMA onto NR by gamma irradiation at a dose of 5 kGy for producing thermoplastic elastomers [4]. The objective of this project is to report the results of studies of radiation graft-copolymerization of methyl methacrylate (MMA) or styrene (St) onto natural rubber latex in order to improve their physico-mechanical properties and evaluation of grafted material using Small-Angle Neutron Scattering through FNCA Project. The grafting degree of MMA and St onto NR increased with the increase of irradiation dose and monomer concentration. The alteration of grafted products structure was determined by IR method. Tensile strength, Shore A hardness, 100% modulus of grafted products increased with the increase of monomer concentration and irradiation dose while elongation at break decreased. The grafted products were characterized by Transmission Electron

Vulcanization of polybutadiene latex induced by 60Co γ-rays irradiation

International Nuclear Information System (INIS)

Liu Yuguang; Huang Yudong; Hou Jing; Gao Deyu; Zhang Xuequan

2007-01-01

Fully vulcanized polybutadiene rubber particles (FVBR) were prepared by polybutadiene latex (PBL) vulcanization induced by 60 Co γ-rays irradiation, and the effect of absorbed dose on crosslinking behavior was studied. Mean diameter, diameter distribution and morphology of the particles in the PBL irradiated at different doses as well as in the FVBR were characterized by laser particle analyzer and AFM. The crosslinking effect on the mechanical properties of the films, by casting from PBL at different doses correspondingly, was evaluated by mechanical and dynamic mechanical analysis (DMA) respectively. The results showed that the diameter and swelling property decreased with absorbed dose, while crosslink density and gel fraction increased. Moreover, the decrease of the tensile strength and elongation at break, the increase of the hardness in shore A and young's modulus (E), and the increase of storage modulus (E') and narrowing of loss tangent peak (Tan 8) were all accounted for the increment of crosslinking. The Charlesby-Pinner equation fits well with the PBL vulcanization in the range of absorbed doses from 0 to 200kGy. (authors)

Production of medical supplies from elastomers vulcanized with ionizing radiation

International Nuclear Information System (INIS)

Guedes, Selma M.L.; Collantes, Hugo David Chirinos; Kodama, Yasko

1996-01-01

The silicon was vulcanized by gamma rays in the absence of organic peroxides. The natural rubber latex was vulcanized by gamma rays and electron beams in the absence and presence of sensitizer. The surgical gloves fabricated with latex containing nB-A vulcanized by gamma rays can be commercialized. Another expected applications are the development of the catheter and the material utilized in the radiotherapy treatment. (author)

Vulcanization Kinetics of Natural Rubber Based On Free Sulfur Determination

Directory of Open Access Journals (Sweden)

Abu Hasan

2013-05-01

Full Text Available The determination of free sulfur in the rubber vulcanizates provided significant representation of vulcanization reaction. In this research, the effects of vulcanization temperature, the mixing method of carbon black into rubber, the ingredients mixing sequence and the type of carbon black were studied on masticated and milled natural rubber in which the reaction was observed by un-reacted sulfur determination. The results showed that higher vulcanization temperature provided faster vulcanization reaction and greater reaction rate constant. Similarly, the mixing sequence of ingredient and carbon black into rubber influenced the rate of vulcanization reaction. The subsequent ingredients mixing sequence, in this case, resulted in higher vulcanization rate compared to that of the simultaneous one. However, the mixing method of carbon black into rubber brought small effect on the rate of vulcanization reaction. The type of carbon black applied was observed to influence the reaction rate of vulcanization. Smaller particle sizes of carbon black gave larger reaction rate constant. In this case, the type of carbon black N 330 gave faster vulcanization rate than that of N 660.

Toxicological evaluation of natural rubber films from vulcanized latex by the conventional process and the alternative process with ionizing radiation; Avaliacao toxicologica de filmes de borracha natural obtidos do latex vulcanizado pelo processo convencional e pelo processo alternativo com radiacao ionizante

Energy Technology Data Exchange (ETDEWEB)

Campos, Vania Elisabeth

1997-07-01

The industrial vulcanization of natural rubber latex (NRL) is made all over the world by conventional process using sulphur and heat but it can be made by an alternative process using ionizing radiation. In this research the NRL was tested by 13 physical, chemical and mechanical assays which showed its good quality. It was done a preliminary study of the toxicological properties of 4 natural rubber films obtained by casting process of NRL: one non vulcanized, other vulcanized by the conventional process and two vulcanized by the alternative process. In the alternative process the films were obtained by irradiation of NRL by gamma rays from the {sup 60} Co source at 250 kGy in the absence of sensitizer and irradiated NRL at 12 kGy in the presence of 4ph r of n-butyl acrylate / 0.2 phr of KOH. These vulcanization doses were determined from broken tensile strength. In the conventional process, sulphur vulcanized NRL was made using a classical composition. Another film was made with non vulcanized NRL. The preliminary evaluation of the toxicological properties was made from in vitro cytotoxicity and in vivo systemic toxicity assays. The LBN films vulcanized by the alternative process have less cytotoxicity than the NRL film vulcanized by the conventional process. The sensitized vulcanized films by gamma rays and non vulcanized films showed similar cytotoxicity while the vulcanized films without sensitizer showed a slight lower cytotoxicity. The non vulcanized NRL film and the NRL films vulcanized by the alternative process did not show toxic effects in the 72 hours period of the systemic toxicity assay. However the NRL film vulcanized with sulphur induced effects like allaying and motor in coordination on the animals treated with an oil extract at the fourth hour and recovering after that. The alternative process promoted lower toxic effects than conventional process because there was no toxic substances present. (author)

Effect of vulcanization temperature and humidity on the properties of RTV silicone rubber

Science.gov (United States)

Wu, Xutao; Li, Xiuguang; Hao, Lu; Wen, Xishan; Lan, Lei; Yuan, Xiaoqing; Zhang, Qingping

2017-06-01

In order to study the difference in performance of room temperature vulcanized (RTV) silicone rubber in vulcanization environment with different temperature and humidity, static contact angle method, FTIR and TG is utilized to depict the properties of hydrophobicity, transfer of hydrophobicity, functional groups and thermal stability of RTV silicone rubber. It is found that different vulcanization conditions have effects on the characteristics of RTV silicone rubber, which shows that the hydrophobicity of RTV silicone rubber changes little with the vulcanization temperature but a slight increase with the vulcanization humidity. Temperature and humidity have obvious effects on the hydrophobicity transfer ability of RTV silicone rubber, which is better when vulcanization temperature is 5°C or vulcanization humidity is 95%. From the Fourier transform infrared spectroscopy, it can be concluded that humidity and temperature of vulcanization conditions have great effect on the functional groups of silicone rubber, and vulcanization conditions also have effect on thermal stability of RTV silicone rubber. When vulcanization temperature is 5°C or vulcanization humidity is 15% or 95%, the thermal stability of silicone rubber becomes worse.

Cream concentrated latex for foam rubber products

Science.gov (United States)

Suksup, R.; Imkaew, C.; Smitthipong, W.

2017-12-01

Fresh natural latex (around 40% rubber and 60% water) can be transformed to concentrated natural latex (around 60% rubber and 40% water) in order to realise economical transportation and easier latex product’s preparation. The concentrated natural latex is an extremely valuable material. It can be applied for many types of products, for example, foam rubber as pillow and mattress, elastic band, etc. Industrially, the concentrated natural latex can be prepared by centrifugation which requires an enormous expensive machine. From the eco-friendly products point of view, most of rubber entrepreneurs in the world try to develop a green rubber product. So, the main objective of this study is to prepare the cream concentrated latex without any sophisticated machine. Thus, we work on a simple, cheap and green method that does not use any expensive machine but uses water-based chemical as sodium alginate to prepare the cream concentrated latex. The optimal amount of sodium alginate in the latex was studied. The main characteristics of the cream concentrated latex were tested by various technics, such as alkalinity, total solid content (TSC), dry rubber content (DRC), etc. We found that there are no significant differences of results between fresh natural latex and cream concentrated latex, except for the TSC and DRC. The TSC and DRC of cream latex are higher than those of fresh natural latex. Finally, we propose a model of natural rubber particle and sodium alginate to form the cream concentrated latex.

Pilot Scale Production of Irradiated Natural Rubber Latex and its Dipping Products

Directory of Open Access Journals (Sweden)

M. Utama

2005-07-01

Full Text Available One hundred and fifty kg natural rubber latex (NRL before and after concentration were added with 3 phr (part hundred ratio of rubber normal butyl acrylate, then the mixture were irradiated at 25 kGy by gamma rays of 60Co in pilot scale. The irradiated natural rubber latex (INRL were then being to use for producing rubber products such as condom, surgical gloves, and spygmomanometer in factory scale. The quality of INRL and rubber products such as : total solid content (TSC, dry rubber content (DRC, KOH, VFA and MST number, tensile strength, modulus, elongation at break, extractable protein content, and response against Type I allergy etc. were evaluated. The economic aspect for producing INRL by means of Gamma Irradiator (GI and Electron Beam Machine (EBM such as payback period (PP, net present value (NPV and internal rate return (IRR were calculated. The results showed that the latex properties of INRL such as DRC, TSC, KOH, VFA, and MST number are not only found to the requirement of the ISO 2004 standard but also the latex has low protein, lipid, and carbohydrate content. The physical and mechanical properties (tensile strength, modulus, and elongation at break of rubber dipping products such as condom, gloves, and sphygmomanometer are not only found to the requirement of ISO 4074, ISO 10282, and ANSI/AAMI SP-1994 standards, but also the allergic response tested clinical latex-sensitive protein allergen by ELISA test on gloves, and by SPT test on condom are found to be negative. It indicates that production of INRL or PVNRL or RVNRL by EBM 250 keV/10 mA, was more cheap than by using gamma γ irradiator 200 kCi, or sulfur vulcanization. The value of PBP (payback period was 2,1 years, NPV (net present value was 4,250 US $, PI (profitability index 1,06 and IRR (internal rate of returns was 25,0%.

Safety Evaluation Test on Human for Radiation Pre vulcanised Natural Rubber Latex (RVNRL)

International Nuclear Information System (INIS)

Pairu Ibrahim; Wan Manshol Wan Zain; Chai, Chee Keong; Sofian Ibrahim; Saadiah Sulaiman; Sharifah Ismail

2010-01-01

This paper discussed about clinical test conducted to determine safety evaluations on human for latex examination gloves and latex films made from Radiation Vulcanized Natural Rubber Latex (RVNRL). Two types of test were being adopted which are i) Modified Draize-95 test and ii) Patch Test on Sensitized Individuals. Modified Draize-95 test was conducted on 200 non-sensitized human subjects and Patch Test on Sensitized Individuals was conducted on 25 individuals who are allergic to the defined major chemical sensitizer presents in natural rubber product. It was found that Modified Draize-95 test has prove that there is no clinical evidence on the presence of residual chemical additives at the level that may induce Type IV allergy in the un sensitized general user population in the RVNRL gloves. Meanwhile Patch Test on Sensitized Individuals has proved that the patch test conducted using the test article on 25 individuals who are allergic to the defined major chemical sensitizers present in natural rubber products, thiuram, carbamates or thiazoles produced a negative response, meeting the pre requirement for the claim of reduced reaction-inducing potential. (author)

The Effect of Gamma Irradiation on the Mechanical Properties of vulcanized Natural Rubber and Natural Rubber-Polyethylene Blends

International Nuclear Information System (INIS)

Sudradjat Iskandar

2008-01-01

To enhance the quality of vulcanized natural rubber and natural rubber-polyethylene blends, gamma irradiation has been done. The compound of natural rubber and natural rubber-polyethylene blends made by using roll mill machine. The mixed materials were antioxidant, anti ozon, plasticizer and vulcanisator. The natural rubber and natural rubber-polyethylene blends compound were vulcanizer and made a slab (film of sample) using hot and could press machine. The slabs produced were then gamma irradiated at irradiation dose of 75, 150 and 300 kGy. Before and after irradiation, the slab were characterized using strograph R1 machine. The results showed that the modulus 300 and hardness of vulcanized natural rubber and natural rubber-polyethylene blends were increasing; the tensile strength and tear strength were increasing to maximum level then decreasing with gamma irradiation, while the elongation at break was decreasing. The maximum tensile strength of vulcanized natural rubber and natural rubber-polyethylene blends were found at irradiation dose of 75 kGy. At the irradiation dose of 75 kGy, the tensile strength of vulcanized natural rubber increased from 17.6 MN/m 2 to 21.2 MN/m 2 , while the tensile strength of vulcanized natural rubber-polyethylene blends increased slightly from 18.7 MN/m 2 to 19.4 MN/m 2 . (author)

Electron linear accelerator system for natural rubber vulcanization

Science.gov (United States)

Rimjaem, S.; Kongmon, E.; Rhodes, M. W.; Saisut, J.; Thongbai, C.

2017-09-01

Development of an electron accelerator system, beam diagnostic instruments, an irradiation apparatus and electron beam processing methodology for natural rubber vulcanization is underway at the Plasma and Beam Physics Research Facility, Chiang Mai University, Thailand. The project is carried out with the aims to improve the qualities of natural rubber products. The system consists of a DC thermionic electron gun, 5-cell standing-wave radio-frequency (RF) linear accelerator (linac) with side-coupling cavities and an electron beam irradiation apparatus. This system is used to produce electron beams with an adjustable energy between 0.5 and 4 MeV and a pulse current of 10-100 mA at a pulse repetition rate of 20-400 Hz. An average absorbed dose between 160 and 640 Gy is expected to be archived for 4 MeV electron beam when the accelerator is operated at 400 Hz. The research activities focus firstly on assembling of the accelerator system, study on accelerator properties and electron beam dynamic simulations. The resonant frequency of the RF linac in π/2 operating mode is 2996.82 MHz for the operating temperature of 35 °C. The beam dynamic simulations were conducted by using the code ASTRA. Simulation results suggest that electron beams with an average energy of 4.002 MeV can be obtained when the linac accelerating gradient is 41.7 MV/m. The rms transverse beam size and normalized rms transverse emittance at the linac exit are 0.91 mm and 10.48 π mm·mrad, respectively. This information can then be used as the input data for Monte Carlo simulations to estimate the electron beam penetration depth and dose distribution in the natural rubber latex. The study results from this research will be used to define optimal conditions for natural rubber vulcanization with different electron beam energies and doses. This is very useful for development of future practical industrial accelerator units.

The Effect of Paraffin Wax to Properties of Radiation Vulcanization Natural Rubber Latex (RVNRL)

International Nuclear Information System (INIS)

Mohd Noorwadi Mat Lazim; Sofian Ibrahim; Muhammad Saiful Omar

2015-01-01

Dipping factories often encounter a serious problem with high tackiness of the finish products during storage. The tackiness effect can be lead to rejection of products. This tackiness effect of natural (NR) rubber film originates in the free rubber chain ends at the surface of the film. The tackiness is not depends on the degree of crosslinking (vulcanization), since radiation itself unable to reduce the tackiness effect. The RVNRL requires addition of additive or anti-tack agent into formulation to reduce tackiness effect. In this experiment, paraffin wax manufactured by Emulco Sdn Bhd under the trade name Aquawax 48 was added into RVNRL formulation as anti-tack and the effect of paraffin wax to physical and mechanical properties of RVNRL was study. (author)

Performance Study of the Natural Rubber Composite with Clay Minerals

International Nuclear Information System (INIS)

Nyo Nyo Myint; Tin Tin Aye; Kyaw Myo Naing; Nyunt Wynn

2008-03-01

The preparation, characterization and some applications of natural rubber clay composite have been studied. This study investigated the possibility of natural rubber latex to replace some part of natural clays. In formulation of rubber clay composite from natural rubber latex and various clay minerals, three main steps were involved (i) preparation of latex cream (ii) prevulcanization of latex cream (iii) mixing vulcanized latex compound, with other ingredients. In each step, several parameters have been carefully investigated to optimize the performance of natural rubber clay composite production. The composite products were of better quality and can be considered to be more cost effective.

Degradation of blending vulcanized natural rubber and nitril rubber (NR/NBR) by dimethyl ether through variation of elastomer ratio

Science.gov (United States)

Saputra, A. H.; Juneva, S.; Sari, T. I.; Cifriadi, A.

2018-04-01

Dimethyl ether can cause degradation of the rubber material seal in some applications. In order to use of natural rubber in industry, research about a blending of natural rubber (NR) and nitrile rubber (NBR) to produce rubber to meet the standard seal material application were conducted. This study will observe the degradation mechanisms that occur in the blending natural rubber and nitrile rubber (NR/NBR) by dimethyl ether. Nitrile rubber types used in this study is medium quality nitrile rubber with 33% of acrylonitrile content (NBR33). The observed parameters are percent change in mass, mechanical properties and surface morphology. This study is limited to see the effect of variation vulcanized blending ratio (NR/NBR33) against to swelling. The increase of nitrile rubber (NBR33) ratio of blending rubber vulcanized can reduce the tensile strength and elongation. The best elastomer variation was obtained after comparing with the standard feasibility material of seal is rubber vulcanized blending (NR/NBR33) with ratio 40:60 NR: NBR.

Radio-vulcanization of natural rubber in the latex phase. Study of an experimental 1 tonne per hour production; Radio-vulcanisation du caoutchouc naturel en phase latex. Etude d'une production experimentale de 1 tonne par heure

Energy Technology Data Exchange (ETDEWEB)

Leveque, P; Puig, J R; Roudeix, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-07-01

After briefly reviewing the main research carried out on the radio-vulcanization of latex and elastomers, a description is given of 4 types of cell which have been used successively with a view to industrial irradiation. They have made it possible to acquire the information necessary for resolving the main problem arising during irradiation - the formation of coagulum. The first two cell are designed for irradiation by a horizontal beam ('Dynamitron'), the two others use a vertical beam ('Circe'). The study of the properties of the rubber obtained shows it to compare favorably with 'Revultex'. In the appendix are given some characteristics of natural latex and information about its processing. (authors) [French] Apres un rappel des principales etudes sur la radio-vulcanisation du latex et des elastomeres, on decrit les quatre types de cellules successivement essayes en vue de l'irradiation industrielle. Ils ont permis d'acquerir les informations necessaires a la resolution du probleme principal pose par l'irradiation, la formation de coagulum au cours de celle,-ci. Les deux premiers sont concus pour l'irradiation par un faisceau horizontal ('Dynamitron'), les derniers par un faisceau vertical ('Circe'). L'etude des proprietes du caoutchouc obtenu montre qu'il se compare favorablement au 'Revultex'. Un apercu est donne en annexe des caracteristiques du latex naturel et de sa mise en oeuvre. (auteurs)

Production of medical supplies from elastomers vulcanized with ionizing radiation; Obtencao de artefatos medicos a partir de elastomeros vulcanizados com radiacao ionizante

Energy Technology Data Exchange (ETDEWEB)

Guedes, Selma M.L.; Collantes, Hugo David Chirinos; Kodama, Yasko [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

1996-07-01

The silicon was vulcanized by gamma rays in the absence of organic peroxides. The natural rubber latex was vulcanized by gamma rays and electron beams in the absence and presence of sensitizer. The surgical gloves fabricated with latex containing nB-A vulcanized by gamma rays can be commercialized. Another expected applications are the development of the catheter and the material utilized in the radiotherapy treatment. (author)

Vulcanization of rubber mixtures by simultaneous electron beam and microwave irradiation

Energy Technology Data Exchange (ETDEWEB)

Martin, D. E-mail: martin@ifin.nipne.ro; Ighigeanu, D.; Mateescu, E.; Craciun, G.; Ighigeanu, A

2002-08-01

The comparative results obtained by applying separate electron beam (EB) irradiation and simultaneous EB and microwave (MW) irradiation to vulcanization of rubber mixtures based on natural rubber and polybutadiene rubber with carbon black are presented. In the absence of MW, EB irradiation doses of 200-250 kGy are required in order to obtain a higher vulcanization degree. The irradiation doses as well as irradiation times were markedly diminished, from 2 to 6 times, by simultaneous EB and MW irradiation.

Environmental Exposure and Accelerated Testing of Rubber-to-Metal Vulcanized Bonded Assemblies

Science.gov (United States)

1974-11-01

btadiene/acrylonitrile ( NBR ) rubber -to-metat -. canized bonded assemblies at the two exposure sites are shown in Table 5. After exposure for one year...AD-A0-17 368 EN~VIRONMENTAL EXPOSURE AND ACCELERATED TESTING OF RUBBER -TO-METAL VULCANIZED BONDED ASSEMBLIES John A. WilliamsI Rock Island Arseital...COMMERCE 325116 1AD R-TR-75-013 ENViRONMENTAL EXPOSURE AND ACCELERATED TESTING OF RUBBER -TO-METAL VULCANIZED BONDED ASSEMBLIES by __ John A. Williams

ESR investigation of NR and IR rubber vulcanized with different cross-link agents

Directory of Open Access Journals (Sweden)

P. Posadas

2016-01-01

Full Text Available This study evaluates the formation of radical species in natural rubber (NR and poly-isoprene rubber (IR during the vulcanization process and the uniaxial deformation of the formed networks by means of Electron Spin Resonance (ESR. Vulcanization of NR and IR always shows a radical pathway, where the different vulcanization systems dictate the concentration of radical species in the course of this complex process. The greatest concentration of radicals were detected during the vulcanization with sulfur/accelerator based on efficient systems (EV, followed by conventional (CV and sulfur donor systems, whereas azide and organic peroxide agents showed smaller concentration of radicals. Independently of the vulcanization system, certain amount of radicals was detected on the vulcanized samples after the end of the vulcanization process. Comparison between different matrices demonstrates that NR always shows higher concentration of radicals than IR in the vulcanization process as well as during uniaxial deformation, fact that could be associated to the presence of nonrubber components in NR.

The Effect of Novel Binary Accelerator System on Properties of Vulcanized Natural Rubber

Directory of Open Access Journals (Sweden)

Moez Kamoun

2009-01-01

Full Text Available The mechanical properties, curing characteristics, and swelling behaviour of vulcanized natural rubber with a novel binary accelerator system are investigated. Results indicate that the mechanical properties were improved. Crosslinking density of vulcanized natural rubber was measured by equilibrium swelling method. As a result, the new binary accelerator was found to be able to improve both cure rate and crosslinking density. Using the numerical analysis of test interaction between binary accelerator and operational modelling of vulcanization-factors experiments, it can be concluded that the interaction (Cystine, N-cyclohexyl-2-benzothiazyl sulfenamide was significant and the optimum value of binary accelerator was suggested, respectively, at levels 0 and +1.

Exploiting epoxidized natural rubber latex (ENRL) as a starting raw material for latex-based products

Science.gov (United States)

Siti Nor Qamarina, M.; Fatimah Rubaizah, M. R.; Nurul Suhaira, A.; Norhanifah, M. Y.

2017-12-01

Epoxidized natural rubber latex (ENRL) is a chemically modified natural rubber latex produced from epoxidation process that involves usage of organic peracids. Conversion of the ENRL into dry rubber products has been known to exhibit many beneficial properties, however limited published works were found on diversifiying the ENRL latex-based products applications. In this preliminary work, different source of raw materials and neutralization systems were investigated. The objective was to explore possibilities in producing distinctive ENRL. Findings have demonstrated that different source of raw materials and neutralization systems influenced the typical ENRL specifications, stability behavior and particle size distribution. Morphological observations performed on these ENRL systems appeared to agree with the ENRL characteristics achieved. Since experimenting these two main factors resulted in encouraging ENRL findings, detailed work shall be further scrutinized to search for an optimum condition in producing marketable ENRL specifically for latex-based products applications.

Allergenicity of latex rubber products used in South African dental ...

African Journals Online (AJOL)

Fourteen latex examination gloves (powdered and non-powdered) and five dental rubber dams, representing 6 brands, from five dental academic institutions were analysed for latex allergens and total protein. Total protein content was determined using the BioRad DC protein assay kit and natural rubber allergen levels ...

Natural rubber latex: past, present and future in Latin America

International Nuclear Information System (INIS)

Lugao, A.B.; Miranda, A.; Mindrisz, A.C.; Andrade e Silva, L.G. de

1996-01-01

The origin of the Hevea braziliensis tree was the Amazonian region in South America, particularly the Brazilian jungle. The rubber expansion at the end of 9th century brought prosperity and determined the borders of Amazonian countries. In spite of that, the Brazilian government has failed in establishing a successful policy for improving the NR production in the jungle. However, rubber plantations were successfully introduced recently near marginal areas of the humid forest in the Amazon due to the absence of the fungus Microcyclos ulei. Both, extraction of wild rubber and plantation have a key role in the maintenance of the forest health. The market for dipping products is small but is growing very fast and is expected to follow this pattern as the sanitary conditions are improved by the health authority. The history of the Brazilian NR products industry is contemporary and is based on the policy of market protection and on the lack of investments due to extremely high interest rates. As a result, the industry was not competitive. It was concluded that, in order to cope with the future challenge, the industry is required to invest in very modern technologies to produce first class goods with international acceptance. Latin America would follow the world trend for nitrosamine and protein free products. The radiation vulcanization of natural rubber latex could prove itself as a profitable solution and not only a quality solution. It was also concluded that both wild rubber and rubber plantations in Brazil have their future coupled with the future of a regional dipping industry. Moreover, the buildup of the dipping industry will be beneficial to the protection of the humid forest and the recovery of degraded areas

Design of Self-Healing Supramolecular Rubbers by Introducing Ionic Cross-Links into Natural Rubber via a Controlled Vulcanization.

Science.gov (United States)

Xu, Chuanhui; Cao, Liming; Lin, Baofeng; Liang, Xingquan; Chen, Yukun

2016-07-13

Introducing ionic associations is one of the most effective approaches to realize a self-healing behavior for rubbers. However, most of commercial rubbers are nonpolar rubbers without now available functional groups to be converted into ionic groups. In this paper, our strategy was based on a controlled peroxide-induced vulcanization to generate massive ionic cross-links via polymerization of zinc dimethacrylate (ZDMA) in natural rubber (NR) and exploited it as a potential self-healable material. We controlled vulcanization process to retard the formation of covalent cross-link network, and successfully generated a reversible supramolecular network mainly constructed by ionic cross-links. Without the restriction of covalent cross-linkings, the NR chains in ionic supramolecular network had good flexibility and mobility. The nature that the ionic cross-links was easily reconstructed and rearranged facilitating the self-healing behavior, thereby enabling a fully cut sample to rejoin and retain to its original properties after a suitable self-healing process at ambient temperature. This study thus demonstrates a feasible approach to impart an ionic association induced self-healing function to commercial rubbers without ionic functional groups.

Radiation vulcanization of ethylene-propylene rubber with polyfunctional monomers

Energy Technology Data Exchange (ETDEWEB)

Jinhua, Wang; Yoshii, Fumio; Makuuchi, Keizo

2001-01-01

This paper reports on the sensitizing efficiency of several polyfunctional monomers to radiation vulcanization of ethylene-propylene rubber. And the results show that triethyleneglycol dimethacrylate (TEGDMA) gave the best results. TEGDMA not only lowers the vulcanization dose (D{sub v}), but also increases the tensile strength greatly. The content of TEGDMA does not affect the D{sub v} of TEGDMA-EPM, but affects the tensile strength at the D{sub v}. At best content (0.04 mol/100 g EPM), the tensile strength is increased from 6.0 to 12 MPa, and the elongation is 790% at the D{sub v}. (author)

Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

International Nuclear Information System (INIS)

Dessouki, A.M.; Taher, N.H.; El-Nahas, H.H.

1996-01-01

The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the ζ potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs

Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

Dessouki, A M; Taher, N H; El-Nahas, H H [National Center for Radiation Research and Technology, Atomic Energy Athority, Cairo (Egypt)

1996-03-01

The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the {zeta} potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs.

Study on irradiation condition in radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Zhu Nankang; Wang Chunlei; Makuuchi, K.; Yoshii, F.

1996-01-01

The effect of gamma rays irradiation dose rates on RVNRL preparation was studied using Malaysian latex added with O.2 phr of KOH and 5 phr n-BA. The results showed, to ensure the tensile strength of the latex film meet the requirement, when applying vulcanisation doses, Dv of 20 kGy 20 and 15 kGy, irradiation dose rates should not be greater than 0. 49 kGy/hr and 1. 6 kGy/hr respectively. Its was found that within the storage time of 20 days there was no change in the physical properties of the latex films

Reinforcing Natural Rubber with Cellulose Nanofibrils Extracted from Bleached Eucalyptus Kraft Pulp

Science.gov (United States)

Chunmei Zhang; Tianliang Zhai; Ronald Sabo; Craig Clemons; Yi Dan; Lih-Sheng Turng

2014-01-01

Reinforced natural rubber (NR) nanocomposites were prepared by solution mixing, casting, and evaporation of pre-vulcanized natural rubber latex and an aqueous suspension of cellulose nanofibrils (CNFs) extracted from bleached eucalyptus kraft pulp. Scanning electron microscopy (SEM) images showed that there were no micro-scaled aggregates observed in the nanocomposites...

The working of RVNRL pilot plant of Rubber Board and it's safety devices

International Nuclear Information System (INIS)

Britto, I.J.; Thomas, E.V.

1996-01-01

A pilot plant for producing radiation vulcanized natural rubber latex (RVNRL) was established at Rubber Board, India in 1992. Irradiation is done by a batch process in the plant. The plant has a versatile safety system for safety of operators and people working in and around the plant

Comparative studies on sulfur, peroxide, and radiation vulcanization of EFDM rubber

International Nuclear Information System (INIS)

Abdel-Aziz, M.M.; Basfar, A.A.; Mofti, S.

2000-01-01

The temperature and concentration dependence of the vulcanization characteristics and mechanical properties of epdm rubber containing various concentrations of peroxide compounds was studied. The peroxides used are Luperox Di, Luperox 500-40 Ke, peroximon Dc Sc and peroximon Dc 40 Ke. The optimum cure parameters for the different types of peroxides indicated that Luperox Di, relatively, Give the best properties among the studied peroxides. The mechanical properties of EPDM containing different concentrations of Luperox Di and vulcanized at different temperatures were compared with those of either radiation or sulfur-cured EPDM. The modulus stress and tensile strength of the Luperox Di-cured EPDM were found to increase with either increasing the temperature of vulcanization and/ or concentration of the peroxide. Moreover, the tensile strength values are much higher than those of the sulfur-cured samples, except for those with low concentration of peroxide and vulcanized at relatively low temperature. A comparable result to those of the chemically vulcanized samples was attained by the radiation- vulcanized samples containing 1 phr of crosslinking agent and irradiated to 150 KGy

Improved properties of dissimilar rubber-rubber blends using plasma polymer encapsulated curatives : a novel surface modification method to improve co-vulcanization

NARCIS (Netherlands)

Guo, R.

2009-01-01

In industrial applications, different rubber types are often blended to fine-tune or optimize the property portfolio required for successful performance of articles. Considering the complexity of a rubber blend compound, wherein numerous additives are involved, vulcanization or cure mismatch often

MATERIAL PARAMETER OF RUBBER GLOVE VULCANIZED USING COMBINED INFRARED AND HOT-AIR HEATING

OpenAIRE

Tipapon Khamdaeng; Numpon Panyoyai; Thanasit Wongsiriamnuay

2014-01-01

Vulcanization is an important chemical-thermal process in production of rubber products resulting in change of material properties, increased elasticity and strength. In general, Young’s modulus is used as an indicator of elastic deformation at loading configuration. However, rubber is not truly elastic and a single parameter is insufficient to describe the whole deformation contributed by microstructure of rubber network. Therefore, we present the material parameters concerning the mec...

Latex Rubber Gloves as a Sampling Dosimeter Using a Novel Surrogate Sampling Device.

Science.gov (United States)

Sankaran, Gayatri; Lopez, Terry; Ries, Steve; Ross, John; Vega, Helen; Eastmond, David A; Krieger, Robert I

2015-01-01

Pesticide exposure during harvesting of crops occurs primarily to the workers' hands. When harvesters wear latex rubber gloves for personal safety and hygiene harvesting reasons, gloves accumulate pesticide residues. Hence, characterization of the gloves' properties may be useful for pesticide exposure assessments. Controlled field studies were conducted using latex rubber gloves to define the factors that influence the transfer of pesticides to the glove and that would affect their use as a residue monitoring device. A novel sampling device called the Brinkman Contact Transfer Unit (BCTU) was constructed to study the glove characteristics and residue transfer and accumulation under controlled conditions on turf. The effectiveness of latex rubber gloves as sampling dosimeters was evaluated by measuring the transferable pesticide residues as a function of time. The validation of latex rubber gloves as a residue sampling dosimeter was performed by comparing pesticide transfer and dissipation from the gloves, with the turf transferable residues sampled using the validated California (CA) Roller, a standard measure of residue transfer. The observed correlation (Pearson's correlation coefficient R(2)) between the two methods was .84 for malathion and .96 for fenpropathrin, indicating that the BCTU is a useful, reliable surrogate tool for studying available residue transfer to latex rubber gloves under experimental conditions. Perhaps more importantly, these data demonstrate that latex gloves worn by workers may be useful quantifiable matrices for measuring pesticide exposure.

Mechanical Properties of Dynamically Vulcanized Thermoplastic Polyurethane (TPU/Polybutadiene Rubber (BR Blends

Directory of Open Access Journals (Sweden)

Ji-Hoo Kim

2017-01-01

Full Text Available To obtain thermoplastic polyurethane (TPU with low hardness, dynamically vulcanized TPU/polybutadiene rubber(BR(70/30 blends were prepared. The effect of dicumyl peroxide (DCP content and stabilizers on the tensile strength and elongation at break of the dynamically vulcanized blends was examined. The tensile strength and elongation at break of the dynamically vulcanized blends decrease with increasing content of DCP. The addition of optimal content of stabilizer leads to the improvement of tensile strength and elongation at break of the blends. Also, the effect of sulfur cure systems and accelerators on the tensile strength and elongation of the blends was investigated. The tensile strength and elongation at break of all the dynamically vulcanized TPU/BR (70/30 blends using 1-step processing are not higher than those of simple TPU/BR (70/30 blends. However, the tensile strength and elongation of the dynamically vulcanized blends prepared at 8 min (mixing time using 2-step processing are higher than those of the simple blends.

Surface modification of halloysite nanotubes by vulcanization accelerator and properties of styrene-butadiene rubber nanocomposites with modified halloysite nanotubes

Energy Technology Data Exchange (ETDEWEB)

Zhong, Bangchao; Jia, Zhixin, E-mail: zxjia@scut.edu.cn; Hu, Dechao; Luo, Yuanfang; Guo, Baochun; Jia, Demin

2016-03-15

Graphical abstract: - Highlights: • Vulcanization accelerant was used to modify halloysite nanotubes (HNTs). • The modified HNTs reduced the activation energy of vulcanization. • Strong filler–rubber interaction was achieved in rubber/modified HNTs composites. • The modified HNTs exhibited excellent reinforcement effect on rubber. - Abstract: Vulcanization accelerant N-cyclohexyl-2-benzothiazole sulfenamide (CZ) was used as a surface modifier and chemically grafted on the surface of halloysite nanotubes (HNTs) to obtain CZ-functionalized HNTs (HNTs-s-CZ). It was found that HNTs-s-CZ could be homogeneously dispersed into styrene-butadiene rubber (SBR). The grafted CZ molecules, exactly located at the filler-rubber interface, reduced the activation energy of vulcanization of SBR/HNTs-s-CZ compounds. Besides, the density of chain segments introduced by the interfacial phase of SBR/HNTs-s-CZ nanocomposites was higher than the other nanocomposites with silane-modified HNTs (m-HNTs) or pristine HNTs, manifesting an indication of enhanced filler-rubber interfacial interaction in SBR/HNTs-s-CZ nanocomposites. Consequently, SBR/HNTs-s-CZ nanocomposites showed excellent mechanical properties. The tensile strength could be enhanced by as much as 38.6% and 102.5% compared to those of SBR/m-HNTs and SBR/HNTs nanocomposites, respectively, though containing equivalent accelerant component. The value of this work lies in the fact that apparent properties improvement of elastomer composites has been achieved by the incorporation of vulcanization accelerant-functionalized HNTs, which may be fruitful for the rational design of filler surface treatment and offer new scientific and technological opportunities for the preparation of high performance elastomer composites.

Surface modification of halloysite nanotubes by vulcanization accelerator and properties of styrene-butadiene rubber nanocomposites with modified halloysite nanotubes

International Nuclear Information System (INIS)

Zhong, Bangchao; Jia, Zhixin; Hu, Dechao; Luo, Yuanfang; Guo, Baochun; Jia, Demin

2016-01-01

Graphical abstract: - Highlights: • Vulcanization accelerant was used to modify halloysite nanotubes (HNTs). • The modified HNTs reduced the activation energy of vulcanization. • Strong filler–rubber interaction was achieved in rubber/modified HNTs composites. • The modified HNTs exhibited excellent reinforcement effect on rubber. - Abstract: Vulcanization accelerant N-cyclohexyl-2-benzothiazole sulfenamide (CZ) was used as a surface modifier and chemically grafted on the surface of halloysite nanotubes (HNTs) to obtain CZ-functionalized HNTs (HNTs-s-CZ). It was found that HNTs-s-CZ could be homogeneously dispersed into styrene-butadiene rubber (SBR). The grafted CZ molecules, exactly located at the filler-rubber interface, reduced the activation energy of vulcanization of SBR/HNTs-s-CZ compounds. Besides, the density of chain segments introduced by the interfacial phase of SBR/HNTs-s-CZ nanocomposites was higher than the other nanocomposites with silane-modified HNTs (m-HNTs) or pristine HNTs, manifesting an indication of enhanced filler-rubber interfacial interaction in SBR/HNTs-s-CZ nanocomposites. Consequently, SBR/HNTs-s-CZ nanocomposites showed excellent mechanical properties. The tensile strength could be enhanced by as much as 38.6% and 102.5% compared to those of SBR/m-HNTs and SBR/HNTs nanocomposites, respectively, though containing equivalent accelerant component. The value of this work lies in the fact that apparent properties improvement of elastomer composites has been achieved by the incorporation of vulcanization accelerant-functionalized HNTs, which may be fruitful for the rational design of filler surface treatment and offer new scientific and technological opportunities for the preparation of high performance elastomer composites.

Properties of Vulcanized Polyisoprene Rubber Composites Filled with Opalized White Tuff and Precipitated Silica

Directory of Open Access Journals (Sweden)

Suzana Samaržija-Jovanović

2014-01-01

Full Text Available Opalized white tuff (OWT with 40 μm average particle size and 39.3 m2/g specific surface area has been introduced into polyisoprene rubber (NR. Their reinforcing effects were evaluated by comparisons with those from precipitated silica (PSi. The cure characteristic, apparent activation energy of cross-link (Eac and reversion (Ear, and mechanical properties of a variety of composites based on these rubbers were studied. This was done using vulcanization techniques, mechanical testing, and scanning electron microscopy (SEM. The results showed that OWT can greatly improve the vulcanizing process by shortening the time of optimum cure (tc90 and the scorch time (ts2 of cross-linked rubber composites, which improves production efficiency and operational security. The rubber composites filled with 50 phr of OWT were found to have good mechanical and elastomeric properties. The tensile strengths of the NR/OWT composites are close to those of NR/PSi composites, but the tear strength and modulus are not as good as the corresponding properties of those containing precipitated silica. Morphology results revealed that the OWT is poorly dispersed in the rubber matrix. According to that, the lower interactions between OWT and polyisoprene rubber macromolecules are obtained, but similar mechanical properties of NR/OWT (100/50 rubber composites compared with NR/PSi (100/50 rubber composites are resulted.

Properties of natural rubber/attapulgite composites prepared by latex compounding method: Effect of filler loading

International Nuclear Information System (INIS)

Muttalib, Siti Nadzirah Abdul; Othman, Nadras; Ismail, Hanafi

2015-01-01

This paper reports on the effect of filler loading on properties of natural rubber (NR)/attapulgite (ATP) composites. The NR/ATP composites were prepared by latex compounding method. It is called as masterbatch. The masterbatch was subsequently added to the NR through melt mixing process. The vulcanized NR/ATP composites were subjected to mechanical, swelling and morphological tests. All the results were compared with NR/ATP composites prepared by conventional system. The composites from masterbatch method showed better results compared to composites prepared by conventional method. They have higher tensile properties, elongation at break and tear strength. The images captured through scanning electron microscopy test revealed the improvement of tensile strength in masterbatch NR/ATP composites. It can be seen clearly that masterbatch NR/ATP have better filler dispersion compared to conventional method NR/ATP composites

Properties of natural rubber/attapulgite composites prepared by latex compounding method: Effect of filler loading

Energy Technology Data Exchange (ETDEWEB)

Muttalib, Siti Nadzirah Abdul, E-mail: sitinadzirah.amn@gmail.com; Othman, Nadras, E-mail: srnadras@usm.my; Ismail, Hanafi, E-mail: ihanafi@usm.my [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, Seri Ampangan, 14300 Nibong Tebal, Pulau Pinang (Malaysia)

2015-07-22

This paper reports on the effect of filler loading on properties of natural rubber (NR)/attapulgite (ATP) composites. The NR/ATP composites were prepared by latex compounding method. It is called as masterbatch. The masterbatch was subsequently added to the NR through melt mixing process. The vulcanized NR/ATP composites were subjected to mechanical, swelling and morphological tests. All the results were compared with NR/ATP composites prepared by conventional system. The composites from masterbatch method showed better results compared to composites prepared by conventional method. They have higher tensile properties, elongation at break and tear strength. The images captured through scanning electron microscopy test revealed the improvement of tensile strength in masterbatch NR/ATP composites. It can be seen clearly that masterbatch NR/ATP have better filler dispersion compared to conventional method NR/ATP composites.

Preparation of highly stabilised natural rubber latex for radiation vulcanisation

International Nuclear Information System (INIS)

Kulatunge, S.S.; Nadarajah, M.; Kalyani, N.M.V.; Chandralal, H.N.K.K.; Devendra, R.

1996-01-01

There is a bright future for radiation vulcanised natural rubber latex (RVNRL) but there are problems in manufacturing it as the centrifuged latex to be used for radiation has to be kept for at least a month or sometimes even three to six months before adding the sensitisers and even then the latex sometimes coagulates on adding the sensitisers. This paper describes a process by which the latex can be stabilised by addition of an anionic soap before centrifuging so that it has a high mechanical stability and hence can be used even within one week of the manufacture of the centrifuged latex

ODC-Free Solvent Implementation Issues for Vulcanized Rubber and Bond Systems

Science.gov (United States)

Hodgson, James R.; McCool, Alex (Technical Monitor)

2001-01-01

Thiokol Propulsion has worked extensively to replace 1,1,1-trichloroethane (TCA) with ozone depleting chemicals (ODC)-free solvents for use in the manufacture of the Reusable Solid Rocket Motor (RSRM) for the Space Shuttle Program. As Thiokol has transitioned from sub-scale to full-scale testing and implementation of these new solvents, issues have been discovered which have required special attention. The original intent of Thiokol's solvent replacement strategy was to replace TCA with a single drop-in solvent for all equivalent applications. We have learned that a single candidate does not exist for replacing TCA. Solvent incompatibility with process materials has caused us to seek for niche solvents and/or processing changes that provide an ODC-free solution for special applications. This paper addresses some of the solvent incompatibilities, which have lead to processes changes and possible niche solvent usage. These incompatibilities were discovered during full-scale testing of ODC-free solvents and relate to vulcanized rubber and bond systems in the RSRM. Specifically, the following items are presented: (1) Cure effects of d-limonene based solvents on Silica Filled Ethylene Propylene Diene Monomer (SF-EPDM) rubber. During full-scale test operations, Thiokol discovered that d-limonene (terpene) based solvents inhibit the cure of EPDM rubber. Subsequent testing showed the same issue with Nitrile Butadiene Rubber (NBR). Also discussed are efforts to minimize uncured rubber exposure to solvents; and (2) Cured bond system sensitivity to ODC-free solvents. During full scale testing it was discovered that a natural rubber to steel vulcanized bond could degrade after prolonged exposure to ODC-free solvents. Follow on testing showed that low vapor pressure and residence time seemed to be most likely cause for failure.

Natural rubber latex: determination and interpretation of flow curves

Directory of Open Access Journals (Sweden)

Harrison Lourenço Corrêa

2015-08-01

Full Text Available AbstractAs consumers become more demanding, the importance grows of guaranteeing the quality of products. The employment of reliable testing techniques that assure the origin and characteristics of the inputs used by industry is a key factor in this respect. In the rubber processing industry, the most commonly used characterization tests include determination of the total solids and dry rubber content, mechanical stability, odor, color and presence of volatile compounds, among others. For the most part, these tests are sufficient for the latex transformation industry. However, in situations where there is a need to know the behavior of latex in reaction to the mechanical forces of machines (mixers, pumps, etc., other tests must be used. Rheological tests to determine viscoelastic data by means of plotting flow curves combined with the application of theoretical models can provide important details for characterization of different types of latex. This article presents the protocol employed by the Rheology and Image Laboratory of Rio de Janeiro State University (UERJ for the rheological study of Brazilian latex. The samples analyzed came from the state of São Paulo.

A novel thermoplastic elastomer based on dynamically vulcanized polypropylene/acrylic rubber blends

Directory of Open Access Journals (Sweden)

2008-08-01

Full Text Available Thermoplastic elastomer based on polypropylene (PP and acrylic rubber (ACM was investigated, with special attention on the compatibilization and dynamic vulcanization. ACM component contains chlorine and carboxyl groups along the backbone, which act as center for the curing and reactive compatibilization. The last event was carried out by adding a combination of maleic anhydride-modified PP (PP-g-MA and triethylene tetramine (TETA, which act as interfacial agents between PP and ACM phases. The effectiveness of the compatibilization was suggested from mixing torque and viscosity, determined from rheological measurements. Outstanding mechanical performance, especially elongation at break, and better tensile set (lower values were obtained with the compatibilization. The dynamic vulcanization also resulted in good mechanical properties for compatibilized blends, but the performance was inferior to that observed for non vulcanized blends. The effect of the compatibilization and/or dynamic vulcanization on the dynamic mechanical, thermal, morphological and stress relaxation properties was investigated.

Type I allergy to natural rubber latex and type IV allergy to rubber chemicals in health care workers with glove-related skin symptoms.

Science.gov (United States)

Nettis, E; Assennato, G; Ferrannini, A; Tursi, A

2002-03-01

It has been established that there are type I and type IV allergens in latex gloves. The purpose of the study was to establish the prevalence of rubber glove-induced skin symptoms among health care workers in one Italian hospital. Health care workers (n = 1584) were evaluated using a written questionnaire and 295 respondents with glove-induced skin symptoms were tested. We performed: skin prick test with latex glove extract and commercial latex, and environmental and food allergens; glove use test; patch tests with a rubber additive series; and RASTs. Hospital employees who used or had used latex gloves at work were 1294. Three hundred and sixteen (24.4%) reported glove-induced symptoms, namely, cutaneous symptoms in all the cases and non-cutaneous symptoms in 105 subjects (8.1%). Twenty-seven of the 295 symptomatic employees tested (9.1%) were latex sensitive. Thirty-one patients (10.5%) exhibited positive patch test to rubber-related allergens. The most positive readings were obtained from the Thiuram mix and the Carba mix, with 12 and 9 positivities, respectively. The risk factors for latex skin sensitization were: a previous history of atopy and asthma; history of surgery; pre-existing hand dermatitis; work-related symptoms; and positive skin tests to common inhalant and certain foods (P skin complaints of latex gloves are related to skin irritation rather than to allergy. The immediate allergy to latex and the delayed allergy to rubber chemicals suggest that all the health care workers with glove-related dermatitis should undergo both skin prick test and glove use test to detect type I hypersensitivity to latex, and patch test to detect type IV hypersensitivity to rubber chemicals.

Multifunctional Peroxidegas Alternative Crosslink Agents for Dynamically Vulcanized Expoxidized Natural Rubber/Polypropylene Blends

NARCIS (Netherlands)

Thitithammawong, A.; Thitithammawong, A.; Sahakaro, Kannika; Noordermeer, Jacobus W.M.

2009-01-01

Commonly used dicumyl peroxide (DCP) in combination with coagent, triallyl cyanurate (TAC), as a crosslinking agent is well acceptable for dynamically vulcanized rubber phase of thermoplastic vulcanizates (TPVs). However, it generally produces volatile decomposition products, which cause a typical

Gamma irradiator design concepts for radiation vulcanisation of natural rubber latex

International Nuclear Information System (INIS)

Aggarwal, K.S.; Muralidharan, P.; Apte, M.G.; Kalurkar, A.R.; Shah, B.M.

1990-01-01

Radiation vulcanisation of natural rubber latex (NRL) is a new and yet unproven technology and one which involves undefined problems of consumer acceptance and high degree of radiation risk. Therefore, the designer should take care that the initial capital cost of the plant is as low as possible to keep the unit processing cost low during the initial lean period of the product requirement by the market. Three irradiators to process natural rubber latex have been designed as per capacity requirement of the user. Their salient features are described. (author). 2 tabs., 24 figs

High concentrations of natural rubber latex allergens in gloves used ...

African Journals Online (AJOL)

Introduction. Gloves made of natural rubber latex (NRL) are commonly used by healthcare workers because of their good qualities. However, allergic reactions to latex allergens are still commonly reported. Objective. To measure the concentrations of Hev b 1, Hev b 3, Hev b 5 and Hev b 6.02 allergens in gloves used by a ...

Color Spectrum Properties of Pure and Non-Pure LATEX in Discriminating Rubber Clone Series

International Nuclear Information System (INIS)

Noor Aishah Khairuzzaman; Hadzli Hashim; Nina Korlina Madzhi; Noor Ezan Abdullah; Faridatul Aima Ismail; Ahmad Faiz Sampian; Azhana Fatnin Che Will

2015-01-01

A study of color spectrum properties for pure and non-pure latex in discriminating rubber clone series has been presented in this paper. There were five types of clones from the same series being used as samples in this study named RRIM2002, RRIM2007, RRIM2008, RRIM2014, and RRIM3001. The main objective is to identify the significant color spectrum (RGB) from pure and non-pure latex that can discriminate rubber clone series. The significant information of color spectrum properties for pure and non-pure latex is determined by using spectrometer and Statistical Package for the Social Science (SPSS). Visible light spectrum (VIS) is used as a radiation light of the spectrometer to emit light to the surface of the latex sample. By using SPSS software, the further numerical analysis of color spectrum properties is being conducted. As the conclusion, blue color spectrum for non-pure is able to discriminate for all rubber clone series whereas only certain color spectrum can differentiate several clone series for pure latex. (author)

Capacitance Regression Modelling Analysis on Latex from Selected Rubber Tree Clones

International Nuclear Information System (INIS)

Rosli, A D; Baharudin, R; Hashim, H; Khairuzzaman, N A; Mohd Sampian, A F; Abdullah, N E; Kamaru'zzaman, M; Sulaiman, M S

2015-01-01

This paper investigates the capacitance regression modelling performance of latex for various rubber tree clones, namely clone 2002, 2008, 2014 and 3001. Conventionally, the rubber tree clones identification are based on observation towards tree features such as shape of leaf, trunk, branching habit and pattern of seeds texture. The former method requires expert persons and very time-consuming. Currently, there is no sensing device based on electrical properties that can be employed to measure different clones from latex samples. Hence, with a hypothesis that the dielectric constant of each clone varies, this paper discusses the development of a capacitance sensor via Capacitance Comparison Bridge (known as capacitance sensor) to measure an output voltage of different latex samples. The proposed sensor is initially tested with 30ml of latex sample prior to gradually addition of dilution water. The output voltage and capacitance obtained from the test are recorded and analyzed using Simple Linear Regression (SLR) model. This work outcome infers that latex clone of 2002 has produced the highest and reliable linear regression line with determination coefficient of 91.24%. In addition, the study also found that the capacitive elements in latex samples deteriorate if it is diluted with higher volume of water. (paper)

Thermal stability of radiation vulcanized EPDM rubber

International Nuclear Information System (INIS)

Abdel-Aziz, M.M.

2005-01-01

Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) have been used to study the thermal stability of gamma- ray vulcanized ethylene-propylene diene rubber (EPDM) stabilized with various types of antioxidants. The antioxidants used were penta erythrityl tetrakis(3,5- di-tert-butyl(-4-hydroxyphenyl)propionate (Irganox 1010), Irganox 1035, Irganox 1520 D, as primary antioxidants; Irganox B 561 and Irganox B 900, as synergistic blends; hindered amine light stabilizer (HALS), i.e. Tinuvin 622 LD; N-isopropyl-N-phenyl-p-phenylene diamine (IPPD) and Trimethyl quinoline (TMQ) and their mixtures. The measurements were carried out under atmospheric conditions. The effect of antioxidant type, selected concentration and mechanism of reaction were determined

NMR relaxation times of natural rubber latex

International Nuclear Information System (INIS)

Harun, S.; Aziz, H.; Basir, Z.

1994-01-01

NMR relaxation times T sub 1 and T sub 2 of natural rubber latex have been measured at 25 degree C on a pulsed NMR spectrometer. The work focuses on the variation of the relaxation times with the amount of water content from 0% to 50%. The water content was adjusted by centrifuging and removing a certain amount of water from the sample. The data were analysed using a biexponential fitting procedure which yields simultaneously either T sub 1a and T sub 1b or T sub 2a and T sub 2b. The amount of solid was compared with the known amount of dry rubber content

Costs and return analysis in rubber latex production in Edo State ...

African Journals Online (AJOL)

The study examined the costs and return analysis in rubber latex production in Edo Sate, Nigeria. Multi-stage sampling method was adopted to select 96 smallholder rubber framers for the study. The first stage was a purposive sampling of two LGAs and then simple random sampling of 6 villages each from the two LGA.

Isolation rubber latex binary composites consisting of cotton and poly-N, N-dimethyl-N, N-diallilammony chloride

Directory of Open Access Journals (Sweden)

J. Cornejo Tueros

2012-01-01

Full Text Available The paper discusses the application of rubber from latex binary coagulating agent consisting of cotton - textile waste and polymeric quaternary ammonium salts. The influence on the process of extracting rubber from latex flow coagulating agent temsperatury and concentration of the dispersed phase.

Marine bacterial prodigiosin as dye for rubber latex, polymethyl ...

African Journals Online (AJOL)

Prodigiosin is known for its immunomodulatory, antibacterial, antimycotic, antimalarial, algicidal and anticancer activities. Here, we reported the evaluation of prodigiosin pigment as a dyeing agent in rubber latex, paper and polymethyl methacrylate (PMMA) so that it can be considered as an alternative to synthetic pigments.

Maillard Reaction in Natural Rubber Latex: Characterization and Physical Properties of Solid Natural Rubber

Directory of Open Access Journals (Sweden)

S. Montha

2016-01-01

Full Text Available Maillard reaction in Natural Rubber (NR latex was investigated by treating fresh NR latex with glutaraldehyde (C5H8O2 in amounts of 0, 50, 100, and 200 mmol/kg of latex. Protein cross-linking in fresh NR latex and solid NR was confirmed by using sodium dodecylsulfate polyacrylamide gel electrophoresis (SDS-PAGE and attenuated total reflection infrared (ATR-IR spectroscopy, respectively. It was found that degree of protein cross-linking in NR increased with increasing C5H8O2 concentration. Physical properties of untreated and treated NR substances in terms of gel content, initial Wallace plasticity (P0, plasticity retention index (PRI, Mooney viscosity, and tensile strength were carefully explored. Results clearly showed that the Maillard cross-linking of proteins had remarkable effect on bulk NR properties, that is, solvent resistance, hardness, resistance to oxidation, rheological behavior, and resistance to stretching out.

Comparative Proteomics of Rubber Latex Revealed Multiple Protein Species of REF/SRPP Family Respond Diversely to Ethylene Stimulation among Different Rubber Tree Clones

Directory of Open Access Journals (Sweden)

Zheng Tong

2017-05-01

Full Text Available Rubber elongation factor (REF and small rubber particle protein (SRPP are two key factors for natural rubber biosynthesis. To further understand the roles of these proteins in rubber formation, six different genes for latex abundant REF or SRPP proteins, including REF138,175,258 and SRPP117,204,243, were characterized from Hevea brasiliensis Reyan (RY 7-33-97. Sequence analysis showed that REFs have a variable and long N-terminal, whereas SRPPs have a variable and long C-terminal beyond the REF domain, and REF258 has a β subunit of ATPase in its N-terminal. Through two-dimensional electrophoresis (2-DE, each REF/SRPP protein was separated into multiple protein spots on 2-DE gels, indicating they have multiple protein species. The abundance of REF/SRPP proteins was compared between ethylene and control treatments or among rubber tree clones with different levels of latex productivity by analyzing 2-DE gels. The total abundance of each REF/SRPP protein decreased or changed a little upon ethylene stimulation, whereas the abundance of multiple protein species of the same REF/SRPP changed diversely. Among the three rubber tree clones, the abundance of the protein species also differed significantly. Especially, two protein species of REF175 or REF258 were ethylene-responsive only in the high latex productivity clone RY 8-79 instead of in RY 7-33-97 and PR 107. Some individual protein species were positively related to ethylene stimulation and latex productivity. These results suggested that the specific protein species could be more important than others for rubber production and post-translational modifications might play important roles in rubber biosynthesis.

PROPERTIES TYRE TREAD RUBBERS DEPENDING ON PARTICULARITY OF RUBBER COMPOUND

Directory of Open Access Journals (Sweden)

Z. S. Shashok

2014-01-01

Full Text Available Summary. The results of studies of the elastomeric compositions based on natural rubber containing curatives different ratio "curing agent : vulcanization accelerator" listed in this article. Influence of the composition of the vulcanizing group on stress-strain and elastic- deformation properties of tire tread rubber was installed. It has been shown that a significant effect on thermo-oxidative aging of vulcanizates was the composition of the vulcanizing group. Results of studies resistance tread rubber to exposure to elevated temperatures were presented . Vulcanizates differing type and density by varying the cross-linking ratio of "curing agent : vulcanization accelerator" were obtained . Research results in the formation of rubber resistance and crack growth at different temperatures were presented. Revealed that the best education and resistance to tear propagation under normal conditions characterized by rubber ratio "curing agent : vulcanization accelerator" equal to 1.5:1. It has been established that a dynamic endurance study rubbers depends largely on the nature and concentration of the cross-linking cross-links and movable promote increase efficiency due to the grid and reduce the sulfidity rearrangement. During loading mode alternating deformations at elevated temperatures lability of polysulfide bonds negatively affects the performance of rubber, and the decisive role of providing strength and thermal cross-linking. It is shown that the performance of the spatial grid rubbers allow indirectly judge the dynamic vulcanizates endurance and predict performance rubbers at elevated temperatures under conditions of repeated cyclic deformation. Revealed that the vulcanizing system containing sulfur and vulcanization accelerator TBBS 1:2, promotes the formation of the optimal structure of vulcanized rubber , which provides the best resistance to repeated cyclic deformations in the operating temperatures of the tire.

Surface modification of argon/oxygen plasma treated vulcanized ethylene propylene diene polymethylene surfaces for improved adhesion with natural rubber

International Nuclear Information System (INIS)

Basak, Ganesh C.; Bandyopadhyay, Abhijit; Neogi, Sudarsan; Bhowmick, Anil K.

2011-01-01

Vulcanized ethylene propylene diene polymethylene (EPDM) rubber surface was treated in a radio frequency capacitatively coupled low pressure argon/oxygen plasma to improve adhesion with compounded natural rubber (NR) during co-vulcanization. The plasma modified surfaces were analyzed by means of contact angle measurement, surface energy, attenuated total reflection-infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, energy dispersive X-ray sulfur mapping and atomic force microscopy. Several experimental variables such as plasma power, length of exposure time and composition of the argon-oxygen gas mixture were considered. It was delineated that plasma treatment changed both surface composition and roughness, and consequently increased peel strength. The change in surface composition was mainly ascribed to the formation of C-O and -C=O functional groups on the vulcanized surfaces. A maximum of 98% improvement in peel strength was observed after plasma treatment.

Surface modification of argon/oxygen plasma treated vulcanized ethylene propylene diene polymethylene surfaces for improved adhesion with natural rubber

Energy Technology Data Exchange (ETDEWEB)

Basak, Ganesh C. [Rubber Technology Centre, Indian Institute of Technology, Kharagpur 721302 (India); Bandyopadhyay, Abhijit [Department of Polymer Science and Technology, University of Calcutta, Calcutta 700 009 (India); Neogi, Sudarsan [Department of Chemical Engineering, Indian Institute of Technology, Kharagpur 721302 (India); Bhowmick, Anil K., E-mail: anilkb@rtc.iitkgp.ernet.in [Rubber Technology Centre, Indian Institute of Technology, Kharagpur 721302 (India)

2011-01-15

Vulcanized ethylene propylene diene polymethylene (EPDM) rubber surface was treated in a radio frequency capacitatively coupled low pressure argon/oxygen plasma to improve adhesion with compounded natural rubber (NR) during co-vulcanization. The plasma modified surfaces were analyzed by means of contact angle measurement, surface energy, attenuated total reflection-infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, energy dispersive X-ray sulfur mapping and atomic force microscopy. Several experimental variables such as plasma power, length of exposure time and composition of the argon-oxygen gas mixture were considered. It was delineated that plasma treatment changed both surface composition and roughness, and consequently increased peel strength. The change in surface composition was mainly ascribed to the formation of C-O and -C=O functional groups on the vulcanized surfaces. A maximum of 98% improvement in peel strength was observed after plasma treatment.

Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

Energy Technology Data Exchange (ETDEWEB)

Karim, Ahmad Fikri Abdul, E-mail: a.fikri-89@yahoo.com; Ariff, Zulkifli Mohamad [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia); Ismail, Hanafi [Cluster for Polymer Composites (CPC), Science and Engineering Research Centre, Engineering Campus, Universiti Sains Malaysia,14300 Nibong Tebal, Pulau Pinang (Malaysia)

2015-07-22

This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM)

Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

International Nuclear Information System (INIS)

Karim, Ahmad Fikri Abdul; Ariff, Zulkifli Mohamad; Ismail, Hanafi

2015-01-01

This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM)

Science and technology of rubber reclamation with special attention to NR based waste latex products

NARCIS (Netherlands)

Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

2006-01-01

A comprehensive overview of reclamation of cured rubber with special emphasis on latex reclamation is depicted in this paper. The latex industry has expanded over the years to meet the world demands for gloves, condoms, latex thread, etc. Due to the strict specifications for the products and the

Radiation-induced grafting polymerization of MMA onto polybutadiene rubber latex

International Nuclear Information System (INIS)

Peng Jing; Wang Maolin; Qiao Jinliang; Wei Genshuan

2005-01-01

The grafting of methyl methacrylate (MMA) onto polybutadiene rubber latex by the direct radiation method was carried out. The effects of monomer concentration, absorbed dose and dose rate of gamma rays on the grafting yield were investigated. The graft copolymers were characterized by transmission electron microscopy (TEM), FTIR spectroscopy, and differential scanning calorimetry. TEM photographs revealed that the core-shell structures of latex particles are formed at low MMA content, and with the increasing of MMA content, the semi-IPN-like structure with core-shell could be developed due to the high gel fraction of polybutadiene (PBD) seed particles. In addition, infrared analysis confirmed that MMA could be grafted onto PBD molecular chains effectively under appropriate irradiation conditions. The interfacial adhesion between PBD rubber (core) and PMMA (shell) phases could be enhanced with the increase of MMA concentration

Thermo-chemical de-vulcanization of suphur-vulcanized SBR assisted by de-vulcanization aids and oxidation stabilizers

NARCIS (Netherlands)

Saiwari, Sitisaiyidah; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

2013-01-01

Ground tire rubber (GTR) from whole passenger car tires is composed of several types of rubbers and fillers, making de-vulcanization of this material rather complicated. The most critical component in this material is SBR, as it tends to degrade and recombine during the commonly used reclaiming

Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

Energy Technology Data Exchange (ETDEWEB)

Keong, C C; Zin, W M Wan; Ibrahim, P; Ibrahim, S, E-mail: chai@nuclearmalaysia.gov.my [Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

2010-05-15

Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

International Nuclear Information System (INIS)

Keong, C C; Zin, W M Wan; Ibrahim, P; Ibrahim, S

2010-01-01

Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

Trialed production of low protein irradiated natural rubber latex in factory scale by gamma irradiation technique

International Nuclear Information System (INIS)

Utama, Marga; Herwinarni, S.; Halik, H.M.; Siswanto; Suharyanto; Syamsu, Y.; Handoko, B.

2006-01-01

Four tons fresh field natural rubber latex (FNRL) with total solid content 30% were added with 2 phr (part hundred ratio of rubber) normal butyl acrylate (nBA) then irradiated by gamma rays at 25 kGy. The irradiated FNRL was centrifuged, then the properties of irradiated centrifuged natural rubber latex (INRL) and its film were measured before and after storage for 5 months. It is found that the INRL is stable latex during storage in 5 months, with lowest protein, and free nitrosamine content. The tensile strength of INRL film was 24-27 MPa, and modulus 600% was 1,5-2,0 MPa, elongation at break was 900%, and hardness was 27-29 Shore A, while the extractable protein content less than 100 μg/g. (author)

Irradiation grafting of natural rubber latex with maleic anhydride and its compatibilization of poly(lactic acid)/natural rubber blends

Science.gov (United States)

Pongsathit, Siriwan; Pattamaprom, Cattaleeya

2018-03-01

Maleic anhydride (MA) is an interesting monomer to be grafted onto natural rubber(NR) due to its potential as a compatibilizer of hydrophobic rubbers and polymers with higher polarity. So far, radiation grafting of MA onto NR in latex state has not been reported. In this study, the grafting of NR with MA in latex state was investigated by exposing the latex to cobalt-60 gamma irradiation at a fixed MA content of 9% and a varied absorbed doses from 2 to 10 kGy. The FTIR spectrometer, 1H NMR spectrometer and gel content analysis have confirmed successful grafting of MA onto NR after irradiation. The grafted NRs were then used to increase the compatibility and the impact property of PLA/NR blends. It was found that the highest impact strength of the blends was achieved when the grafting was carried out at the absorbed dose of 4 kGy.

Prevalence of Allergy to Natural Rubber Latex and Potential Cross Reacting Food in Operation Room Staff in Shiraz Hospitals -2006

OpenAIRE

H Nabavizade; R Amin

2007-01-01

Introduction & Objective: Allergic reactions to natural rubber latex have increased during past 10 years especially among health care workers and patients with high exposure to latex allergens. Allergic reaction to latex is related to many diseases like occupational asthma. This study was performed to determine the prevalence of allergy to natural rubber latex and potential cross reacting food in operation room staff in Shiraz hospitals. Materials & Methods: In this cross-sectional descr...

Analysis of sulfidic linkages formed in natural rubber latex medical gloves by using X-ray absorption near edge structure

Science.gov (United States)

Chankrachang, M.; Limphirat, W.; Yongyingsakthavorn, P.; Nontakaew, U.; Tohsan, A.

2017-09-01

A study of sulfidic linkages formed in natural rubber (NR) latex medical gloves by using X-ray Absorption Near Edge Structure (XANES) is presented in this paper. The NR latex compound was prepared by using prevulcanization method, that is, it was prevulcanized at room temperature for 24 hrs before utilization. After the 24 hrs of prevulcanization, the latex film samples were obtained by dipping process. The dipped films were subjected to vulcanize at 110°C for 5 to 25 min. It was observed that after the compound was prevulcanized for 24 hrs, polysulfidic linkages were mainly formed in the sample. It was however found that after curing at 110°C for 5-25 min, the polysulfidic linkages are tended to change into disulfide linkages. Especially, in the case of 25 minutes cured sample, disulfide linkages are found to be the main linkages. In term of tensile strength, it was observed that when cure time increased from 5 - 10 min, tensile strengths were also increased. But when the cure time of the film is 25 minutes, tensile strength was slightly dropped. The dropped of tensile strength when cure time is longer than 10 minutes can be ascribed to a degradation of polysulfidic and disulfidic linkages during curing. Therefore, by using XANES analysis, it was found to be very useful to understand the cure characteristic, thus it can be very helpful to optimize cure time and tensile properties of the product.

Evaluation of peptides release using a natural rubber latex biomembrane as a carrier.

Science.gov (United States)

Miranda, M C R; Borges, F A; Barros, N R; Santos Filho, N A; Mendonça, R J; Herculano, R D; Cilli, E M

2018-05-01

The biomembrane natural (NRL-Natural Rubber Latex), manipulated from the latex obtained from the rubber tree Hevea brasiliensis, has shown great potential for application in biomedicine and biomaterials. Reflecting the biocompatibility and low bounce rate of this material, NRL has been used as a physical barrier to infectious agents and for the controlled release of drugs and extracts. The aim of the present study was to evaluate the incorporation and release of peptides using a latex biomembrane carrier. After incorporation, the release of material from the membrane was observed using spectrophotometry. Analyses using HPLC and mass spectroscopy did not confirm the release of the antimicrobial peptide [W 6 ]Hylin a1 after 24 h. In addition, analysis of the release solution showed new compounds, indicating the degradation of the peptide by enzymes contained in the latex. Additionally, the release of a peptide with a shorter sequence (Ac-WAAAA) was evaluated, and degradation was not observed. These results showed that the use of NRL as solid matrices as delivery systems of peptide are sequence dependent and could to be evaluated for each sequence.

Feasibility study on utilization of vitrified radioactive waste as radiation sources

International Nuclear Information System (INIS)

Makuuchi, Keizo; Yoshii, Fumio; Hyakutake, Kenichiro

1995-01-01

A feasibility study on utilization of vitrified high level radioactive waste (VW) as radiation source has been carried out. Natural rubber latex was radiation vulcanized with VW to demonstrate the feasibility. The dose rate was 0.1 kGy/hr. As a sensitizer, n-butyl acrylate was added. Negligible small activation of natural rubber (NR) latex by neutron from the VW was observed. The residual sensitizer in the irradiated latex and physical properties of film molded from the irradiated latex were the same level with the conventional radiation vulcanization of NR latex with γ-rays from Co-60. Surgical gloves and protective rubber gloves for radioactive contamination were produced from 20 litters of NR latex vulcanized with 2 VWs. The physical properties of both gloves were acceptable. These results suggested that vitrified high level waste can be used as an industrial radiation source. (author)

Preparation and evaluation of some investigated natural and acrylonitrile rubber vulcanizations for physiotherapeutic purposes

International Nuclear Information System (INIS)

Helaly, F.M; El-Sawy, S.M.

2005-01-01

A trial was made to design and prepare rubber article that can be used to reactivate, strengthen and reinforce the hand muscles and fingers which had suffered from trouble movement.The investigated rubber article was prepared from natural and acrylonitrile rubber formulations. These formulations were processed in the form of compounds which contain significant quantities of fillers as Hisil, CaCO 3 and TiO 2 .The rheological characteristics and physicochemical properties of the vulcanizations were determined according to standard tests. It was found that it is possible to prepare the designated rubber article for the desired purpose. The test results show that the prepared rubber article has a good chemical resistant against acid, alkali, and salt. Also it possesses high resistance to deterioration and deformation. The prepared article has an ability to retain its elastic property after the action of compressive forces at 70 degree C for 24 hours.This was conformed with applied commercial hand exercise therapeutic article

Development of medical tube fabrication process from RVNRL: optimization and extrusion device at low temperature

International Nuclear Information System (INIS)

Collantes, Hugo David Chirinos

1999-01-01

The natural rubber latex was formulated, irradiation vulcanized and stabilized (GAMATEX) to make rubber goods for medical purpose. When the latex was vulcanized by gamma rays the effectiveness crosslinking of GAMATEX relationship between the concentration ratio of sensitizer system (x 1 =[n-BA]/[KOH]) and the vulcanization dose (x 2 ), showing high interaction grade. The RVNRL process was optimized for low vulcanization doses and high concentrations of n-BA. The resistance to radiolytic oxidation of rubber obtained from GAMATEX was attained when one antioxidants mixture (45% BANOX S + 55% TNPP) was added. This mixture exhibited synergetic effect. The latex showed pseudoplastic rheological behavior and the yield stress occurrence. The irreversible destabilization rate of latex was direct proportional to [n-BA] and indirect proportional to [KOH]. The post-irradiation effects or reversible destabilization of latex occurred because there is a residual concentration of [n-BA] that it was not reacted. The colloidal stability of GAMATEX improved with irradiation, showing showing the increase of thixotropic behavior and the tendency to Newtonian behavior flow besides the relationship between the viscosity index (k) and the pseudoplastic index (n). This fact allows the higher storage time of GAMATEX. The relative viscosity of latex was relationship between the temperature and the total dry rubber content according to the mathematical model: log ηrel = 0,18+1,09r w , where r w is the ratio (BS/100-BS). The radiation vulcanized latex coagulated at -10 deg C into the projected freezing system. (author)

Vulcanization characteristics and dynamic mechanical behavior of natural rubber reinforced with silane modified silica.

Science.gov (United States)

Chonkaew, Wunpen; Minghvanish, Withawat; Kungliean, Ulchulee; Rochanawipart, Nutthaya; Brostow, Witold

2011-03-01

Two silane coupling agents were used for hydrolysis-condensation reaction modification of nanosilica surfaces. The surface characteristics were analyzed using Fourier transform infrared spectroscopy (FTIR). The vulcanization kinetics of natural rubber (NR) + silica composites was studied and compared to behavior of the neat NR using differential scanning calorimetry (DSC) in the dynamic scan mode. Dynamic mechanical analysis (DMA) was performed to evaluate the effects of the surface modification. Activation energy E(a) values for the reaction are obtained. The presence of silica, modified or otherwise, inhibits the vulcanization reaction of NR. The neat silica containing system has the lowest cure rate index and the highest activation energy for the vulcanization reaction. The coupling agent with longer chains causes more swelling and moves the glass transition temperature T(g) downwards. Below the glass transition region, silica causes a lowering of the dynamic storage modulus G', a result of hindering the cure reaction. Above the glass transition, silica-again modified or otherwise-provides the expected reinforcement effect.

Effect of Rubber Nanoparticle Agglomeration on Properties of Thermoplastic Vulcanizates during Dynamic Vulcanization

Directory of Open Access Journals (Sweden)

Hanguang Wu

2016-04-01

Full Text Available We previously reported that the dispersed rubber microparticles in ethylene-propylene-diene monomer (EPDM/polypropylene (PP thermoplastic vulcanizates (TPVs are actually agglomerates of rubber nanoparticles. In this study, based on this new understanding of the microstructure of TPV, we further revealed the microstructure-properties relationship of EPDM/PP TPV during dynamic vulcanization, especially the effect of the size of rubber nanoparticle agglomerates (dn, the thicknesses of PP ligaments (IDpoly and the rubber network on the properties of EPDM/PP TPV. We were able to simultaneously obtain a high tensile strength, elongation at break, elastic modulus, and elasticity for the EPDM/PP TPV by the achievement of a smaller dn, a thinner IDpoly and a denser rubber network. Interestingly, the effect of dn and IDpoly on the elastic modulus of EPDM/PP TPV composed of rubber nanoparticle agglomerates is different from that of EPDM/PP TPVs composed of rubber microparticles reported previously. The deformation behavior of the TPVs during stretching was studied to understand the mechanism for the achievement of good mechanical properties. Interestingly, the rubber nanoparticle agglomerates are oriented along the tensile direction during stretching. The TPV samples with smaller and more numerous rubber nanoparticle agglomerates can slow down the development of voids and cracks more effectively, thus leading to increase in tensile strength and elongation at break of the EPDM/PP TPV.

Effect of the [TiO{sub 2}] on the radiation attenuation properties on the human tissue simulator obtained from radiovulcanized natural rubber latex; Efeito da [TiO{sub 2}] nas propriedades de atenuacao da radiacao no simulador de tecido humano obtido do latex de borracha natural radiovulcanizado

Energy Technology Data Exchange (ETDEWEB)

Tomimasu, Sumie; Guedes, Selma Matheus Loureiro [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil). Centro de Tecnologia das Radiacoes]. E-mail: smguedes@net.ipen.br

2002-07-01

In this paper was studied the concentration effect of TiO{sub 2} used as filler in the radiation attenuation properties of human tissue simulator obtained from radio vulcanized natural rubber. The studied parameters were the following: the mass stopping power (S{sub mas}), the depth at maximum dose (Z{sub max}), the depth at 50% of maximum dose (R{sub 50}) the radiotherapeutic range (RR{sub 80}) and the electrons range (R). The natural rubber latex was formulated with [n-butyl acrylate ] = e phr and [KOH] = 0,2 phr and radio vulcanized by gamma rays (10 kGy) from {sup 60} Co source. The filler TiO{sub 2} was added (0-16 phr). The natural rubber slabs were obtained by casting method and theirs absorbed dose behavior was studied for each filler concentration using electrons beam (6 MeV) from an accelerator. The results showed that the addition of each phr of filler promoted the decrease of 0.019 cm for Z{sub max}, 0.021 cm for RR{sub 80}, 0.033 cm for R and 0.026 cm for R{sub 50} up to [Ti O{sub 2}] 15 phr. The S{sub mas} increased from 1.72 MeVcm2g-1 to 2.00 MeVcm2g-1 in the filler concentration range of 0-16 phr. The filler must be used in the 12-15 phr range. (author)

The influence of temperature and reaction time in the degradation of natural rubber latex

International Nuclear Information System (INIS)

Siti Zaleha Isa; Rosiyah Yahya; Aziz Hassan; Mohd Tahir

2007-01-01

Liquid natural rubber (LNR /LENR) should be considered as a new material instead of a new type of rubber though they have the same configuration as the rubber used. In this work, thermal degradation of natural rubber latex was carried out to obtain LNR/LENR by varying the reaction time at different temperatures. The degraded polymers were characterized structurally using FTIR and NMR spectroscopies and the average molecular weights were determined by membrane-osmometry and viscometry. (author)

ENHANCEMENT OF RESISTANCE TO OXIDATIVE DEGRADATION OF NATURAL RUBBER THROUGH LATEX DEGRADATION

Institute of Scientific and Technical Information of China (English)

无

1998-01-01

A fully characterised natural rubber latex was subjected to mechanical degradation by stirring at intervals. The resistance to oxidative degradation of the different samples were studied by measuring the Plasticity retention indices (PRI).The results show that there is an enhancement of the PRI from 57% for the undegraded rubber to 79% for the one-hour degraded sample. Further degradation resulted in decrease of PRI as time of degradation increased. Therefore, the one-hour degraded sample is a special rubber with high oxidation resistance which is of great importance in engineering.

Properties and Characterization of Kenaf-Filled Natural Rubber Latex Foam

Directory of Open Access Journals (Sweden)

Ahmad Fikri Abdul Karim

2015-12-01

Full Text Available Kenaf powder was incorporated with natural rubber latex (NRL compound and foamed to make natural rubber latex foam (NRLF by using a well known technique called the Dunlop method. Different loadings of kenaf powder were added to NRL compound and was foamed to make NRLF. The mechanical properties, density, compression, thermal, and micro-structural characterization of control NRLF and kenaf incorporated NRLF were studied. Increasing content of kenaf reduced the tensile strength, elongation at break, and compressive strength of a NRLF. Modulus at 100% elongation and density of the NRLF increased with an increase in filler loading. Higher kenaf loading indicated higher elasticity of kenaf-filled NRLF, but the recovery percentage of kenaf-filled NRLF decreased with increasing kenaf loading. From thermogravimetric analysis (TGA result, an increase in the amount of kenaf loading from 1 to 7 phr increased the thermal stability of kenaf-filled NRLF. Morphological and micro-structural characterization performed by using scanning electron microscopy (SEM showed that kenaf powder filled up the micro-sized pores in the open cell structure of kenaf-filled NRLF.

Continuous vulcanization of extruded profile by microwave process

International Nuclear Information System (INIS)

Lim Hun Soo

1994-01-01

Continuous vulcanization is being increasingly used today in the manufacture of extrusion profiles. This is particularly so with the microwave/hot air continuous vulcanization process. Although this process is now quite widely used in Europe and to a lesser extent in USA, it is still not used in Malaysia. To improve the technological capability of the rubber-based industry in extrusion product, the RRIM has acquired a microwave/hot air tunnel continuous vulcanization equipment to enable development work in this area to be carried out with the aim of upgrading the rubber industry towards this more automated manufacturing process. This is particularly pertinent in view of the anticipated labour shortage, and, increasing labour and energy cost. This paper outlines the basic principles of operation of the microwave/hot air tunnel continuous vulcanization process and describes some aspects of compounding involving natural and synthetic rubbers for use in the process. As temperature increase is one of the major factors influencing the vulcanization of profile in this process, study was therefore concentrated on the heat generation aspect in the microwave tunnel

GURU v2.0: An interactive Graphical User interface to fit rheometer curves in Han’s model for rubber vulcanization

OpenAIRE

Milani, G.; Milani, F.

2016-01-01

A GUI software (GURU) for experimental data fitting of rheometer curves in Natural Rubber (NR) vulcanized with sulphur at different curing temperatures is presented. Experimental data are automatically loaded in GURU from an Excel spreadsheet coming from the output of the experimental machine (moving die rheometer). To fit the experimental data, the general reaction scheme proposed by Han and co-workers for NR vulcanized with sulphur is considered. From the simplified kinetic scheme adopted, ...

Prevalence of Allergy to Natural Rubber Latex and Potential Cross Reacting Food in Operation Room Staff in Shiraz Hospitals -2006

Directory of Open Access Journals (Sweden)

H Nabavizade

2007-07-01

Full Text Available Introduction & Objective: Allergic reactions to natural rubber latex have increased during past 10 years especially among health care workers and patients with high exposure to latex allergens. Allergic reaction to latex is related to many diseases like occupational asthma. This study was performed to determine the prevalence of allergy to natural rubber latex and potential cross reacting food in operation room staff in Shiraz hospitals. Materials & Methods: In this cross-sectional descriptive study five hundred eighty operation room staff of ten private and state hospitals in Shiraz completed latex allergy questionnaire. They were questioned about personal history and previous history of latex sensitivity, symptoms of latex reactivity and about other allergies particularly to foods that may cross react with latex. Informed consent was obtained and skin prick testing was performed with natural rubber latex. Skin prick tests were done with three potentially cross reacting food (banana, Kiwi, and potato. The obtained data were analyzed with SPSS software and Chi-square test. Results: Among the 580 operation room workers 104 (17.9 % of participants were positive to latex skin test. We found a significant association between positive skin test to latex in operation room staff and atopy, urticaria and food allergy. Positive skin test to latex related to positive kiwi skin test (p<0.05. The prevalence did not vary by sex, age, education, surgical and non surgical glove users, history of contact dermatitis or smoking status. Conclusion: Latex allergy has a high prevalence in personnel of operation room. Evaluation of present symptom and prediction of future disease necessitate screening test in individuals at risk.

Study on cord/rubber interface at elevated temperatures by H-pull test method

Science.gov (United States)

Jamshidi, M.; Afshar, F.; Mohammadi, N.; Pourmahdian, S.

2005-08-01

Cords are used as reinforcing materials in rubber compounds. To increase cord/rubber interfacial adhesion, they are coated by an adhesive (usually based on resorcinol-formaldehyde-latex). These composites are used in many sectors such as tire and belt industries. Cord/rubber adhesion strength is an important aspect to determine the durability of system. Due to temperature increase during running tires, the adhesion energy becomes different from initial one. To study cord/rubber interface at elevated temperatures, H-adhesion test method was used. H-pull test is a simple method for adhesion evaluation at ambient temperature, so it is usually used for material quality control. In this research, cord/rubber systems were vulcanized at different temperatures and H-adhesion of samples were evaluated at elevated temperatures. Also cord/rubber interface was studied by ATR analyze to determine interfacial interactions kind.

The use of gamma irradiation in preparation of polybutadiene rubber nanopowder; Its effect on particle size, morphology and crosslink structure of the powder

Energy Technology Data Exchange (ETDEWEB)

Rezaei Abadchi, Majid; Jalali-Arani, Azam, E-mail: ajalali@aut.ac.ir

2014-02-01

Highlights: • Vulcanized rubber powders were prepared by spray drying of irradiated rubber latexes. • Influence of absorbed dose on powder structure and characteristics was investigated. • The size of rubber latex particles did not changed by irradiation. • Crosslink density increased by increasing dose and 98% gel was obtained at 150 kGy. • T{sub g} of rubber powder increased with increasing the irradiation dose. -- Abstract: The aim of this work was the preparation and characterization of polybutadiene rubber (BR) powder by irradiating of rubber lattices using {sup 60}Co radiation and spray-drying of them at the appropriate condition. The influences of absorbed dose on the volume swelling ratio, molecular weight between crosslinks, gel fraction, and glass transition temperature of obtained powder were studied. Morphology, size and size distribution of rubber particles were examined by using scanning electron microscopy (SEM) and laser particle size analyzer (LPSA) technique, respectively. Results obtained by LPSA revealed that radiation has no effect on particle size of rubber latex but after drying, adherence properties of rubber particle causes increase in particle size of rubber powder, as shown in SEM photograph. Fourier transform infrared spectroscopy of rubber powders confirmed that with increasing the irradiation dose, characteristic peak corresponds to the >C=C< double bands decreased. Also Charlesby–Pinner equation was used to evaluate radiation yield.

The use of gamma irradiation in preparation of polybutadiene rubber nanopowder; Its effect on particle size, morphology and crosslink structure of the powder

International Nuclear Information System (INIS)

Rezaei Abadchi, Majid; Jalali-Arani, Azam

2014-01-01

Highlights: • Vulcanized rubber powders were prepared by spray drying of irradiated rubber latexes. • Influence of absorbed dose on powder structure and characteristics was investigated. • The size of rubber latex particles did not changed by irradiation. • Crosslink density increased by increasing dose and 98% gel was obtained at 150 kGy. • T g of rubber powder increased with increasing the irradiation dose. -- Abstract: The aim of this work was the preparation and characterization of polybutadiene rubber (BR) powder by irradiating of rubber lattices using 60 Co radiation and spray-drying of them at the appropriate condition. The influences of absorbed dose on the volume swelling ratio, molecular weight between crosslinks, gel fraction, and glass transition temperature of obtained powder were studied. Morphology, size and size distribution of rubber particles were examined by using scanning electron microscopy (SEM) and laser particle size analyzer (LPSA) technique, respectively. Results obtained by LPSA revealed that radiation has no effect on particle size of rubber latex but after drying, adherence properties of rubber particle causes increase in particle size of rubber powder, as shown in SEM photograph. Fourier transform infrared spectroscopy of rubber powders confirmed that with increasing the irradiation dose, characteristic peak corresponds to the >C=C< double bands decreased. Also Charlesby–Pinner equation was used to evaluate radiation yield

Cytotoxicity Comparison of the Nanoparticles Deposited on Latex Rubber Bands between the Original and Stretched State

Directory of Open Access Journals (Sweden)

Jung-Hwan Lee

2014-01-01

Full Text Available Understanding the biocompatibility of nanoparticles in dental materials is essential for their safe usage in the oral cavity. In this study, we investigated whether nanoparticles deposited on orthodontic latex rubber bands are involved in the induction of cytotoxicity. A method of stretching to three times (“3L” the length of the latex rubber bands was employed to detach the particles using the original length (“L” for comparison. The cytotoxicity tests were performed on extracts with mouse fibroblasts (L929 and human gingival fibroblasts (HGFs. Fourier transform infrared spectroscopy, ion chromatography, elemental analysis, and inductively coupled plasma mass spectrometry (ICP-MS were performed to detect the harmful components in the extracts from rubber bands. There was a significant decrease in the cell viability in the “L” samples compared with the “3L” samples (P<0.05 in the L929 and HGF cells. This was due to the Ni single crystal nanoparticles (~50nm from the inner surface of “L” samples that were detached in the “3L” samples as well as the Zn ion (~9 ppm detected in the extract. This study revealed that the Ni nanoparticles, as well as Zn ions, were involved in the induction of cytotoxicity from the latex rubber bands.

Trial production of low protein irradiated natural rubber latex by low energy electron beam in pilot scale

International Nuclear Information System (INIS)

Utama, Marga; Yoshii, F.; Kume, T.

2006-01-01

Three importance factors for producing low protein by low energy electron beam (250 keV/10 mA) irradiation in pilot scale (20 liters per bath) with 1,9-nonediol diacrylate (NDA) namely: maturation time of natural rubber latex before irradiation, treatment of irradiated natural rubber latex (INRL) before and after centrifugation, and standard irradiation method has been carried out. The results showed that the optimum irradiation time for producing INRL with 5 phr (part hundred ratio of rubber) of NDA as sensitize agent, and with the rotation speed of agitation 210 rpm (rotation per minutes) was between 20-30 minutes. By using this condition tensile strength of the INRL film was 26 MPa. The maturation of natural rubber latex before irradiation is the key for driving the quality of INRL. Water extractable protein content of INRL after leaching in 1% ammonia solution for 30 minutes at room temperature was around 47 μ/g, and after adding with 1 phr of PVA (poly vinyl alcohol) or 0.1 phr CMC (carboxy methyl cellulose) the water extractable protein content decrease less than 6 μ/g. (author)

Radiation vulcanised natural rubber latex (RVNRL) market and challenges

International Nuclear Information System (INIS)

Wan Manshol Wan Zin; Najib Mohamad Zakey; Chai Chee Keong

2000-01-01

RVNRL has the required properties and proven useful for the manufacturing of examination gloves, balloons and finger cots at industrial scale. To date only RVNRL finger cots are available in the market. Problems and challenges for the market of other products are identified. Further success in the on going research activities will be the reference for more applications of RVNRL in the relevant industry to produce natural rubber latex products of more competitive values

Radiation vulcanization in Argentina

International Nuclear Information System (INIS)

Ferenaz, Guillermo W.; Smolko, Eduardo E.

1999-01-01

The possibilities of using in Argentina the radiation process to vulcanize natural latex are analyzed. Experimental studies to define the irradiation conditions have been carried out and the preliminary elaboration of an irradiation device that includes the chemical reactor has been started. (author)

In situ reactive compatibilization of natural rubber/acrylic-bentonite composites via peroxide-induced vulcanization

International Nuclear Information System (INIS)

Fu, Lihua; Lei, Zhiwen; Xu, Chuanhui; Chen, Yukun

2016-01-01

To achieve good interfacial interaction between fillers and rubber matrix is always a hot topic in rubber reinforcing industry. In this paper, acid activated bentonite (Bt) was alkalified to be alkaline calcium-bentonite (ACBt), then acrylic acid (AA) was employed to modify ACBt to obtain acrylic-bentonite (ABt). The results of Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) illustrated that acrylate groups were chemically boned onto the surface of Bt and the layer spacing of Bt was increased. During peroxide-induced vulcanization, in situ compatibilization of ABt was realized via the reaction between the unsaturated bonds of acrylate groups on the surface of Bt and the natural rubber (NR) chains. This resulted in an enhanced cross-linked network which contributed to the improved mechanical properties of NR/ABt composites. - Highlights: • Acrylate groups were chemically boned onto the surface of bentonite. • In situ compatibilization was realized via the reaction of acrylate group and NR. • ABt particles participated in forming the NR crosslink network. • A potential reinforcing material options for “white” rubber products.

In situ reactive compatibilization of natural rubber/acrylic-bentonite composites via peroxide-induced vulcanization

Energy Technology Data Exchange (ETDEWEB)

Fu, Lihua; Lei, Zhiwen [Guangxi Key Laboratory of Petrochemical Resource Processing and Process Intensification Technology, School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Xu, Chuanhui, E-mail: xuhuiyee@gxu.edu.cn [Guangxi Key Laboratory of Petrochemical Resource Processing and Process Intensification Technology, School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Chen, Yukun, E-mail: cyk@scut.edu.cn [The Key Laboratory of Polymer Processing Engineering, Ministry of Education, China(South China University of Technology), Guangzhou, 510640 (China)

2016-02-15

To achieve good interfacial interaction between fillers and rubber matrix is always a hot topic in rubber reinforcing industry. In this paper, acid activated bentonite (Bt) was alkalified to be alkaline calcium-bentonite (ACBt), then acrylic acid (AA) was employed to modify ACBt to obtain acrylic-bentonite (ABt). The results of Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) illustrated that acrylate groups were chemically boned onto the surface of Bt and the layer spacing of Bt was increased. During peroxide-induced vulcanization, in situ compatibilization of ABt was realized via the reaction between the unsaturated bonds of acrylate groups on the surface of Bt and the natural rubber (NR) chains. This resulted in an enhanced cross-linked network which contributed to the improved mechanical properties of NR/ABt composites. - Highlights: • Acrylate groups were chemically boned onto the surface of bentonite. • In situ compatibilization was realized via the reaction of acrylate group and NR. • ABt particles participated in forming the NR crosslink network. • A potential reinforcing material options for “white” rubber products.

Study of the effect of ionizing radiation on the structure of natural rubber latex by positron annihilation technique

International Nuclear Information System (INIS)

Lopez Saldana, I.R.

1993-01-01

At the present research, were studied the changes in natural rubber latex structure, due to electron beam by a 3 MeV, 25 m A Dynamitron electron accelerator. The natural rubber latex was irradiated at 30, 40 and 50 kGy/s dose rate, over a total dose range from 150 to 250 kGy, for each dose rate used. From natural rubber latex irradiated films were prepared by casting with 0.7 mm. thickness. In the main part, the study was made by positron annihilation lifetime (PAL), this technique is unique in the determination of free-volume properties due to the fact that positronium atom (Ps) is found to be preferentially localized in the free-volume region of polymeric materials. The positron lifetime measurements were performing using a gamma-gamma coincidence system. These results were analyzed by PATFIT-88 program computer into three components, the long-lived component for orthopositronium (o-Ps) with parameters lifetime (τ 3 ) and formation intensity (I 3 ), were plotted and analyzed for each dose rate and total dose used. Besides with τ 3 were calculated the mean free-volume size based on the spherical model for the free-volume bubble, found that the free-volume decrease slightly with the total dose due to the crosslinking of natural rubber latex. Besides was studied the effect of dose rate on tensile strength, the tensile strength is increased with the total dose although there was not a clear effect due to the dose rate. Also the films were subjected to aging in order to determined the thermal stability of natural rubber latex irradiated, the results show that the films have good stability. Besides was used the infrared spectroscopy to determine the changes due to the crosslinking by variations in the characteristically absorption bands for cis 1,4-polyisoprene. (Author)

Radiation vulcanization of rubbers

Energy Technology Data Exchange (ETDEWEB)

Makuuchi, Keizo [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

2002-02-01

An abstract of the radiation process of polymer materials and the polymer reaction by radiation is explained. Main radiation is 250 keV to 10 MeV of electron rays in the industry. Radiation cross-linked rubber has less the tensile strength than that by sulfur and organic peroxide crosslinking. The main origins of low tensile strength are caused by cut of backbone chain and ozone depend on radiation. Acceleration of crosslinking and short time of radiation are necessary to improve these defects. To accelerate crosslinking, we used crosslinking accelerators, for example, three poly-functional monomers (PFM). The maximum tensile strength of styrene-butadiene rubber (SBR) not added crosslinking accelerators showed 3 MPa at 110 kGy, but SBR added A-TMMT (tetramethylolmethane tetraacrylate) showed 5.5 MPa at 110 kGy. Radiation crosslinking of many kinds of rubber: isoprene (IR), SBR, CR, nitrile rubber (NBR), hydrogenated nitrile rubber (HNBR), butyl rubber (IIR), chlorinated butyl rubber (CIIR), EPM and TPE are explained. (S.Y.)

Radiation vulcanization of rubbers

International Nuclear Information System (INIS)

Makuuchi, Keizo

2002-01-01

An abstract of the radiation process of polymer materials and the polymer reaction by radiation is explained. Main radiation is 250 keV to 10 MeV of electron rays in the industry. Radiation cross-linked rubber has less the tensile strength than that by sulfur and organic peroxide crosslinking. The main origins of low tensile strength are caused by cut of backbone chain and ozone depend on radiation. Acceleration of crosslinking and short time of radiation are necessary to improve these defects. To accelerate crosslinking, we used crosslinking accelerators, for example, three poly-functional monomers (PFM). The maximum tensile strength of styrene-butadiene rubber (SBR) not added crosslinking accelerators showed 3 MPa at 110 kGy, but SBR added A-TMMT (tetramethylolmethane tetraacrylate) showed 5.5 MPa at 110 kGy. Radiation crosslinking of many kinds of rubber: isoprene (IR), SBR, CR, nitrile rubber (NBR), hydrogenated nitrile rubber (HNBR), butyl rubber (IIR), chlorinated butyl rubber (CIIR), EPM and TPE are explained. (S.Y.)

Physical-biopolymer characterization of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) blended with natural rubber latex

Energy Technology Data Exchange (ETDEWEB)

Kuntanoo, K., E-mail: thip-kk@hotmail.com [Graduate School of Khon Kaen University, Khon Kaen, 40002 Thailand (Thailand); Promkotra, S., E-mail: sarunya@kku.ac.th [Department of Geotechnology, Faculty of Technology, Khon Kaen University, Khon Kaen 40002 Thailand (Thailand); Kaewkannetra, P., E-mail: paknar@kku.ac.th [Department of Biotechnology, Faculty of Technology, Khon Kaen University, Khon Kaen 40002 Thailand (Thailand)

2015-03-30

A biopolymer of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) is blended with bio-based materials, natural rubber latex, to improve their microstructures. The various ratios between PHBV and natural rubber latex are examined to develop their mechanical properties. In general, physical properties of PHBV are hard, brittle and low flexible while natural rubber (NR) is presented itself as high elastic materials. Concentrations of the PHBV solution are constituted at 1%, 2% and 3% (w/v). The mixtures of their PHBV solutions to natural rubber latex are produced the blended films in three different ratios of 4:6, 5:5 and 6:4, respectively. They are characterized by appearance analyses which are the scanning electron microscope (SEM), universal testing machine (UTM) and differential scanning calorimetry (DSC). The SEM photomicrographs of the blended films and the controlled PHBV can provide the void distribution in the range of 12-14% and 19-21%, respectively. For mechanical properties of the blended films, the various elastic moduli of 1%, 2% and 3% (w/v) PHBV are the average of 773, 956 and 1,007 kPa, respectively. The tensile strengths of the blends increase with the increased concentrations of PHBV, similarly trend to the elastic modulus. The crystallization and melting behavior of unmixed PHBV and the blends are determined by DSC. Melting transition temperatures (T{sub m}) of the unmixed PHBV are stated two melting peak at 154°C and 173°C. Besides, the melting peaks of the blends alter in the range of 152-156°C and 168-171°C, respectively. According to morphology of the blends, the void distribution decreases twice compared to the unmixed PHBV. The results of mechanical properties and thermal analysis indicate that the blended PHBV can be developed their properties by more resilient and wide range of temperature than usual.

Vulcanization of Rubber

Indian Academy of Sciences (India)

Temperature 140 -180°C. Sulfur. 2-3 parts per. 100 parts of rubber (phr). Accelerator 0.5-1.0 phr. ZnO ... out an experiment, he spilt a mixture of rubber and sulfur with other ingredients on a hot .... both carbon-sulfur and sulfur-nitrogen bonds -.

Radiation graft copolymerization of n-butyl acrylate on natural rubber latex

International Nuclear Information System (INIS)

Sundardi, F.; Kadariah, S.

1986-01-01

A method of radiation graft copolymerization of n-butyl acrylate (NBA) on natural rubber (NR) latex has been studied. The rate of conversion increases with the increase of NBA in latex. An irradiation dose of about 12 kGy is needed to obtain 90% conversion with 40 phr of NBA in latex. Tensile strength, tear strength, and elongation at break of grafted NR are found to decrease with increasing degree of grafting. The physical strength of a vulcanizate prepared from a mixture of NR and ply-NBA was found to be better than that of NBA-NR graft copolymer vulcanizate. The graft copolymerization reaction takes place in the outer layer of NR particles, and because the secondary bonds between poly-NBA molecules may be weaker than those between NR molecules, the existence of a poly-NBA layer in NR particles will decrease its physical strength

Improvement of Some Physical Properties of Loaded Nitrile Rubber Vulcanized by Ionizing Radiation

International Nuclear Information System (INIS)

Abdel-Aziz, M.M.; Basfar, A.A.; Mofti, S.

2000-01-01

The effect of four-selected polyfunctional compounds namely, tri methylacrylic ester, trimethylol propane trimethacrylate, zinc diacrylate and modified pentaerthritol triacrylate, as crosslinking agents, on the mechanical properties of radiation vulcanized nitrile rubber was studied. The effect of incorporation of either HAF-carbon black or fumed silica, as filler and reinforcing agents, on its mechanical properties was also studied. The co agent namely, tri methylacrylic ester, was found to produce a set of optimum mechanical properties, i.e. moderate crosslink density, good tensile strength and elasticity at low irradiation doses, i.e.40 kGy

Mechanical Enhancement of Sensitivity in Natural Rubber Using Electrolytic Polymerization Aided by a Magnetic Field and MCF for Application in Haptic Sensors.

Science.gov (United States)

Shimada, Kunio; Saga, Norihiko

2016-09-18

Sensors are essential to the fulfillment of every condition of haptic technology, and they need simultaneously to sense shear stress as well as normal force, and temperature. They also must have a strong and simple structure, softness, and large extension. To achieve these conditions simultaneously, we enhanced the sensitivity of sensors utilizing natural rubber (NR)-latex through the application of electrolytic polymerization focused on the isoprene C=C bonds in natural rubbers such as NR-latex, and then applied a magnetic field and magnetic compound fluid (MCF) as magnetically responsive fluid. When an electric field alone was used in the rubber, the effect of electrolytic polymerization was very small compared to the effect in well-known conductive polymer solution such as plastic. The MCF developed by Shimada in 2001 involved magnetite and metal particles, and acts as a filler in NR-latex. By utilizing the magnetic, electric fields and the MCF, we aligned the electrolytically polymerized C=C along the magnetic field line with the magnetic clusters formed by the aggregation of magnetite and metal particles so as to enhance the effect of electrolytic polymerization. We then demonstrated the effectiveness of the new method of rubber vulcanization on the sensitivity of the rubber by experimentally investigating its electric and dynamic characteristics.

Mechanical Enhancement of Sensitivity in Natural Rubber Using Electrolytic Polymerization Aided by a Magnetic Field and MCF for Application in Haptic Sensors

Directory of Open Access Journals (Sweden)

Kunio Shimada

2016-09-01

Full Text Available Sensors are essential to the fulfillment of every condition of haptic technology, and they need simultaneously to sense shear stress as well as normal force, and temperature. They also must have a strong and simple structure, softness, and large extension. To achieve these conditions simultaneously, we enhanced the sensitivity of sensors utilizing natural rubber (NR-latex through the application of electrolytic polymerization focused on the isoprene C=C bonds in natural rubbers such as NR-latex, and then applied a magnetic field and magnetic compound fluid (MCF as magnetically responsive fluid. When an electric field alone was used in the rubber, the effect of electrolytic polymerization was very small compared to the effect in well-known conductive polymer solution such as plastic. The MCF developed by Shimada in 2001 involved magnetite and metal particles, and acts as a filler in NR-latex. By utilizing the magnetic, electric fields and the MCF, we aligned the electrolytically polymerized C=C along the magnetic field line with the magnetic clusters formed by the aggregation of magnetite and metal particles so as to enhance the effect of electrolytic polymerization. We then demonstrated the effectiveness of the new method of rubber vulcanization on the sensitivity of the rubber by experimentally investigating its electric and dynamic characteristics.

The Effect of Minarex B Oil and Gamma Irradiation on the Mechanical Properties of Vulcanized Natural Rubber-LDPE Mixture for Shoe Sole

International Nuclear Information System (INIS)

Sudradjat Iskandar; Isni Marliyanti

2004-01-01

To obtain the optimum concentration of minarex B oil and gamma irradiation dose on natural rubber compound for shoe sole, study on the effect of minarex B oil and gamma radiation on the mechanical properties of vulcanized natural rubber-LDPE mixture has been done. Natural rubber was masticated and mixed with additive and filler using two-roll machine, at 120 o C of forward roll and 100 o C of backward roll, with rotation speed of 18 rpm. The additives added with irganox 1076, paraffin wax, stearic acid, and minarex B oil, while fillers used were polyethylene (LDPE) and calcium carbonate. Minarex B oil mixed was vary such as 5, 10 and 20 phr (part per hundred of rubber). The amount of filler and other additives mixed was not varied. The natural rubber film was obtained by pressing the mixture using hot and cold press machine at 135 o C and room temperature for about 3 minutes. The film then irradiated with gamma rays from cobalt-60 source, at the doses of 150, 300, and 500 kGy. The results show that the mechanical properties of natural rubber vulcanized decreases by increasing minarex B oil, and increases by increasing of irradiation dose. The concentration optimum of minarex B oil in the natural rubber compound for shoe sole and irradiation dose about 5 phr and 300 kGy were agree with SII 0944-84. (author)

Evaluation of apparent viscosity of Para rubber latex by diffuse reflection near-infrared spectroscopy.

Science.gov (United States)

Sirisomboon, Panmanas; Chowbankrang, Rawiphan; Williams, Phil

2012-05-01

Near-infrared spectroscopy in diffuse reflection mode was used to evaluate the apparent viscosity of Para rubber field latex and concentrated latex over the wavelength range of 1100 to 2500 nm, using partial least square regression (PLSR). The model with ten principal components (PCs) developed using the raw spectra accurately predicted the apparent viscosity with correlation coefficient (r), standard error of prediction (SEP), and bias of 0.974, 8.6 cP, and -0.4 cP, respectively. The ratio of the SEP to the standard deviation (RPD) and the ratio of the SEP to the range (RER) for the prediction were 4.4 and 16.7, respectively. Therefore, the model can be used for measurement of the apparent viscosity of field latex and concentrated latex in quality assurance and process control in the factory.

Comparative Transcriptome Analysis of Latex Reveals Molecular Mechanisms Underlying Increased Rubber Yield in Hevea brasiliensis Self-Rooting Juvenile Clones.

Science.gov (United States)

Li, Hui-Liang; Guo, Dong; Zhu, Jia-Hong; Wang, Ying; Chen, Xiong-Ting; Peng, Shi-Qing

2016-01-01

Rubber tree (Hevea brasiliensis) self-rooting juvenile clones (JCs) are promising planting materials for rubber production. In a comparative trial between self-rooting JCs and donor clones (DCs), self-rooting JCs exhibited better performance in rubber yield. To study the molecular mechanism associated with higher rubber yield in self-rooting JCs, we sequenced and comparatively analyzed the latex of rubber tree self-rooting JCs and DCs at the transcriptome level. Total raw reads of 34,632,012 and 35,913,020 bp were obtained from the library of self-rooting JCs and DCs, respectively, by using Illumina HiSeq 2000 sequencing technology. De novo assemblies yielded 54689 unigenes from the library of self-rooting JCs and DCs. Among 54689 genes, 1716 genes were identified as differentially expressed between self-rooting JCs and DCs via comparative transcript profiling. Functional analysis showed that the genes related to the mass of categories were differentially enriched between the two clones. Several genes involved in carbohydrate metabolism, hormone metabolism and reactive oxygen species scavenging were up-regulated in self-rooting JCs, suggesting that the self-rooting JCs provide sufficient molecular basis for the increased rubber yielding, especially in the aspects of improved latex metabolisms and latex flow. Some genes encoding epigenetic modification enzymes were also differentially expressed between self-rooting JCs and DCs. Epigenetic modifications may lead to gene differential expression between self-rooting JCs and DCs. These data will provide new cues to understand the molecular mechanism underlying the improved rubber yield of H. brasiliensis self-rooting clones.

Pathway for high-quality reclaim by thermal treatment of sulfur-vulcanized SBR

NARCIS (Netherlands)

Saiwari, Sitisaiyidah; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

2011-01-01

De-vulcanization of SBR (Styrene Butadiene Rubber) is a challenge, as the broken polymer chains tend to re-arrange. This influences the properties of the reclaimed and re-vulcanized rubber, and reduces the quality of the recycled material. Within this study, the breakdown of sulfur-cured SBR in a

Comparative Transcriptome Analysis of Latex Reveals Molecular Mechanisms Underlying Increased Rubber Yield in Hevea brasiliensis Self-Rooting Juvenile Clones

OpenAIRE

Li, Hui-Liang; Guo, Dong; Zhu, Jia-Hong; Wang, Ying; Chen, Xiong-Ting; Peng, Shi-Qing

2016-01-01

Rubber tree (Hevea brasiliensis) self-rooting juvenile clones (JCs) are promising planting materials for rubber production. In a comparative trial between self-rooting JCs and donor clones (DCs), self-rooting JCs exhibited better performance in rubber yield. To study the molecular mechanism associated with higher rubber yield in self-rooting JCs, we sequenced and comparatively analyzed the latex of rubber tree self-rooting JCs and DCs at the transcriptome level. Total raw reads of 34,632,012 ...

The mechanical properties of radiation-vulcanized NR/BR blending system

Energy Technology Data Exchange (ETDEWEB)

Yan Aoshuang E-mail: yanas@public3.bta.net.cn; Guo Zhengtao; Li Li; Zhai Ying; Zhou Peng

2002-03-01

The effect of radiation dose on the mechanical properties of NR/BR blending system is reported in this paper. A comparison was made between sulphur vulcanization and radiation vulcanization for an optimal nature rubber (NR)/ butyl rubber (BR) blending ratio (60/40) at dose range from 10 to 150 kGy. The result shows that the mechanical properties, especially, tensile strength, elongation at break, and tear strength have been improved significantly by radiation-vulcanization. This finding was also proved by thermal aging experiment on a selected NR/BR blend at 70 deg. C for up to 168 h.

Evaluation of some antioxidants in radiation vulcanized ethylene-propylene diene (EPDM) rubber

Energy Technology Data Exchange (ETDEWEB)

Abdel-Aziz, M.M.; Basfar, A.A. E-mail: abasfar@kacst.edu.sa

2001-12-01

Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) have been used to study the oxidation of {gamma}-ray vulcanized ethylene-propylene diene rubber (EPDM) stabilized with various types of antioxidants. The antioxidants used were pentaerythrityl tetrakis(3,5-di-tert-butyl(-4-hydroxyphenyl))propionate (Irganox 1010), Irganox 1035, Irganox 1520D, as primary antioxidants; Irganox B561 and Irganox B900, as synergistic blends; hindered amine light stabilizer (HALS), i.e. Tinuvin 622 LD; N-isopropyl-N-phenyl-p-phenylene diamine (IPPD) and trimethyl quinoline (TMQ) and their mixtures. The measurements were carried out under atmospheric conditions. The effects of antioxidant type and its selected concentration were determined and mechanism of reaction proposed.

Preparation of Low Allergenic Protein Concentrated Natural Rubber Latex Using Suitable Low Molecular Weight Cellulose Derivatives Induced by Gamma Irradiation

International Nuclear Information System (INIS)

Siri-Upathum, Chyagrit; Boonyawat, Jariya

2007-08-01

Full text: Low molecular weight carboxy methyl cellulose (CMC), hydroxyl ethyl cellulose (HEC), hydroxyl propyl cellulose (HPC) and methyl cellulose (MC) prepared by radiation-induced degradation were added into diluted natural concentrated latex prior to centrifuge for a purpose of reducing allergenic rubber protein in the latex. Optimum molecular weight (Mv) of CMC and HEC for such a purpose was found to be 17-18 kDa which decreased allergenic rubber protein (14-94 kDa) to an undetectable amount as determined by SDS PAGE method

Trial Production of Surgical Gloves from Irradiated Natural Rubber Latex on Factory Scale

Directory of Open Access Journals (Sweden)

M. Utama

2005-07-01

Full Text Available Trial production of surgical gloves from irradiated natural rubber latex at the PT. Laxindo Utama Serang Banten glove factory has been carried out. The variation of heating temperature and leaching time during processing were evaluated. The physical and mechanical properties and the protein allergen respond of surgical gloves using ELISA method were measured. The results showed that the physical and mechanical of surgical gloves such as tensile strength, modulus, and elongation at break arefound to meet the requirements of the ISO or SNI standard for surgical gloves. While the allergic response through clinical tested latex-sensitive protein allergen known as ELISA test is found to be negative.

Evaluation of the modified nanoclay effect on the vulcanization of SBR through rheometric curve and DSC;Avaliacao do efeito de nanoargila modificada na vulcanizacao de SBR atraves da curva reometrica e DSC

Energy Technology Data Exchange (ETDEWEB)

Forte, Maria Madalena C.; Brito, Karin J.S., E-mail: mmcforte@ufrgs.b [Universidade Federal do Rio Grande do Sul (PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica; Gheller Junior, Jordao [SENAI, Sao Leopoldo, RS (Brazil). Centro Tecnologico de Polimeros

2009-07-01

Rubber nanocomposites with nanoclays organically modified by quaternary ammonium salts may have the curing features modified significantly, since the salts may act on the rubber cure system. The aim of this work is to evaluate the influences of an organically modified montmorillonite (OMMT) on the curing reaction of an SBR (styrene butadiene rubber) with sulfur. The SBR/OMMT nanocomposites were prepared by co-coagulating SBR latex and Cloisite{sup R} 20A aqueous suspension at different nanoclay concentrations. The OMMT effect on the sulfur curing reaction was evaluated by the rheometric curve using a rheometer type RPA (Rubber Process Analyzer) and the heat of vulcanization (DELTAH{sub v}) using Differential Scanning Calorimetry (DSC). The evaluation of the clay nanolayers dispersion in the SBR matrix was accomplished by x-ray diffraction (XRD) analysis. (author)

Effect of Ingredient Loading on Surface Migration Kinetics of Additives in Vulcanized Natural Rubber Compounds

Directory of Open Access Journals (Sweden)

Bryan B. Pajarito

2014-12-01

Full Text Available Surface migration kinetics of chemical additives in vulcanized natural rubber compounds were studied as function of ingredient loading. Rubber sheets were compounded according to a 212-8 fractional factorial design of experiment, where ingredients were treated as factors varied at two levels of loading. Amount of migrated additives in surface of rubber sheets was monitored through time at ambient conditions. The maximum amount and estimated rate of additive migration were determined from weight loss kinetic curves. Attenuated total reflection–Fourier transform infrared (ATR-FTIR spectroscopy and optical microscopy were used to characterize the chemical structure and surface morphology of sheet specimens during additive migration. ANOVA results showed that increased loading of reclaimed rubber, CaCO3, and paraffin wax signif icantly decreased the maximum amount of additive migration; by contrast, increased loading of used oil, asphalt, and mercaptobenzothiazole disulphide (MBTS increased the maximum amount. Increased loading of sulfur, diphenylguanidine (DPG, and paraffin wax significantly decreased the additive migration rate; increased loading of used oil, asphalt, and stearic acid elicited an opposite effect. Comparison of ATRFTIR spectra of migrated and cleaned rubber surfaces showed signif icant variation in intensity of specif ic absorbance bands that are also present in infrared spectra of migrating chemicals. Paraffin wax, used oil, stearic acid, MBTS, asphalt, and zinc stearate were identified to bloom and bleed in the rubber sheets. Optical micrographs of migrated rubber surfaces revealed formation of white precipitates due to blooming and of semi-transparent wet patches due to bleeding.

Transcript Profiling of Hevea brasiliensis during Latex Flow

Directory of Open Access Journals (Sweden)

Jinquan Chao

2017-11-01

Full Text Available Latex exploitation enhances latex regeneration in rubber trees. The latex exploitation-caused latex flow lasts from 10 min to a few hours, which is convenient for exploring the transcript profiling of latex metabolism-related genes at the different stages of latex flow. In the present study, the expression pattern of 62 latex metabolism-related genes involved in water transportation, carbohydrate metabolism, natural rubber biosynthesis, hormone signaling, ROS generation and scavenging, and latex coagulum across three stages of latex flow between rubber tree clones CATAS7-33-97 and CATAS8-79 were comparatively analyzed by quantitative real-time PCR. The two clones show differences in latex regeneration and have a different duration of latex flow. The results showed that the expression levels of 38 genes were significantly higher in CATAS8-79 latex than in CATAS7-33-97 during latex regeneration, while 45 genes had a notably higher expression level in CATAS8-79 latex during latex flow. Together with the activation of the MEP pathway and jasmonate pathway in CATAS8-79 latex, HbPIP1;3, HbPIP1;4, HbSUT3, HbSus3, HbHMGS1-2, HbMK should contribute to the high latex regeneration ability. The up-regulation of ethylene signaling and Hb44KD and the down-regulation of latex coagulation-related genes in CATAS8-79 latex might contribute to its longer latex flow duration. This study provides some cues for revealing the regulation of latex metabolism in rubber trees.

RoxB Is a Novel Type of Rubber Oxygenase That Combines Properties of Rubber Oxygenase RoxA and Latex Clearing Protein (Lcp).

Science.gov (United States)

Birke, Jakob; Röther, Wolf; Jendrossek, Dieter

2017-07-15

Only two types of rubber oxygenases, rubber oxygenase (RoxA) and latex clearing protein (Lcp), have been described so far. RoxA proteins (RoxAs) are c -type cytochromes of ≈70 kDa produced by Gram-negative rubber-degrading bacteria, and they cleave polyisoprene into 12-oxo-4,8-dimethyltrideca-4,8-diene-1-al (ODTD), a C 15 oligo-isoprenoid, as the major end product. Lcps are common among Gram-positive rubber degraders and do not share amino acid sequence similarities with RoxAs. Furthermore, Lcps have much smaller molecular masses (≈40 kDa), are b -type cytochromes, and cleave polyisoprene to a mixture of C 20 , C 25 , C 30 , and higher oligo-isoprenoids as end products. In this article, we purified a new type of rubber oxygenase, RoxB Xsp (RoxB of Xanthomonas sp. strain 35Y). RoxB Xsp is distantly related to RoxAs and resembles RoxAs with respect to molecular mass (70.3 kDa for mature protein) and cofactor content (2 c -type hemes). However, RoxB Xsp differs from all currently known RoxAs in having a distinctive product spectrum of C 20 , C 25 , C 30 , and higher oligo-isoprenoids that has been observed only for Lcps so far. Purified RoxB Xsp revealed the highest specific activity of 4.5 U/mg (at 23°C) of all currently known rubber oxygenases and exerts a synergistic effect on the efficiency of polyisoprene cleavage by RoxA Xsp RoxB homologs were identified in several other Gram-negative rubber-degrading species, pointing to a prominent function of RoxB for the biodegradation of rubber in Gram-negative bacteria. IMPORTANCE The enzymatic cleavage of rubber (polyisoprene) is of high environmental importance given that enormous amounts of rubber waste materials are permanently released (e.g., by abrasion of tires). Research from the last decade has discovered rubber oxygenase A, RoxA, and latex clearing protein (Lcp) as being responsible for the primary enzymatic attack on the hydrophobic and water-insoluble biopolymer poly( cis -1,4-isoprene) in Gram

Energy usage in the rubber industry

Energy Technology Data Exchange (ETDEWEB)

Soederstroem, M.

1980-01-01

The rubber industry has several energy-intensive steps, such as mastication of natural rubber, mixing and extrusion, and vulcanization. Opportunities for energy savings would be available with a continuous mixing process, heat recovery from cooling waters, and abandonment of thermal conduction in vulcanization. 6 figures. (DCK)

Rubber particle proteins REF1 and SRPP1 interact differently with native lipids extracted from Hevea brasiliensis latex.

Science.gov (United States)

Wadeesirisak, Kanthida; Castano, Sabine; Berthelot, Karine; Vaysse, Laurent; Bonfils, Frédéric; Peruch, Frédéric; Rattanaporn, Kittipong; Liengprayoon, Siriluck; Lecomte, Sophie; Bottier, Céline

2017-02-01

Rubber particle membranes from the Hevea latex contain predominantly two proteins, REF1 and SRPP1 involved in poly(cis-1,4-isoprene) synthesis or rubber quality. The repartition of both proteins on the small or large rubber particles seems to differ, but their role in the irreversible coagulation of the rubber particle is still unknown. In this study we highlighted the different modes of interactions of both recombinant proteins with different classes of lipids extracted from Hevea brasiliensis latex, and defined as phospholipids (PL), glycolipids (GL) and neutral lipids (NL). We combined two biophysical methods, polarization modulated-infrared reflection adsorption spectroscopy (PM-IRRAS) and ellipsometry to elucidate their interactions with monolayers of each class of lipids. REF1 and SRPP1 interactions with native lipids are clearly different; SRPP1 interacts mostly in surface with PL, GL or NL, without modification of its structure. In contrast REF1 inserts deeply in the lipid monolayers with all lipid classes. With NL, REF1 is even able to switch from α-helice conformation to β-sheet structure, as in its aggregated form (amyloid form). Interaction between REF1 and NL may therefore have a specific role in the irreversible coagulation of rubber particles. Copyright © 2016 Elsevier B.V. All rights reserved.

Rubber elongation factor (REF, a major allergen component in Hevea brasiliensis latex has amyloid properties.

Directory of Open Access Journals (Sweden)

Karine Berthelot

Full Text Available REF (Hevb1 and SRPP (Hevb3 are two major components of Hevea brasiliensis latex, well known for their allergenic properties. They are obviously taking part in the biosynthesis of natural rubber, but their exact function is still unclear. They could be involved in defense/stress mechanisms after tapping or directly acting on the isoprenoid biosynthetic pathway. The structure of these two proteins is still not described. In this work, it was discovered that REF has amyloid properties, contrary to SRPP. We investigated their structure by CD, TEM, ATR-FTIR and WAXS and neatly showed the presence of β-sheet organized aggregates for REF, whereas SRPP mainly fold as a helical protein. Both proteins are highly hydrophobic but differ in their interaction with lipid monolayers used to mimic the monomembrane surrounding the rubber particles. Ellipsometry experiments showed that REF seems to penetrate deeply into the monolayer and SRPP only binds to the lipid surface. These results could therefore clarify the role of these two paralogous proteins in latex production, either in the coagulation of natural rubber or in stress-related responses. To our knowledge, this is the first report of an amyloid formed from a plant protein. This suggests also the presence of functional amyloid in the plant kingdom.

Latex allergy in health care

Directory of Open Access Journals (Sweden)

Tina Virtič

2012-11-01

Full Text Available The increasing use of natural rubber latex medical gloves in the last three decades has caused an increase in latex allergy. The majority of risk groups for allergy development include health care workers, workers in the rubber industry, atopic individuals and children with congenital malformations. Three types of pathological reactions can occur in people using latex medical gloves: irritant contact dermatitis, allergic contact dermatitis and immediate hypersensitivity. The latex allergy is caused by constituent components of latex gloves and added powders; there are also numerous latex allergens involved in cross-reactivity between latex and fruits and vegetables, the so-called latex-fruit syndrome. The diagnosis is based on an accurate history of exposure, clinical presentation and confirmatory in vivo and in vitro tests. Prevention is the easiest, most effective and least expensive way to avoid latex allergy. Powder-free latex gloves with reduced levels of proteins and chemicals, and synthetic gloves for allergic workers must be provided in the work environment. There are already many health care institutions around the world where all latex products have been replaced by synthetic material products.

Influence of cure activator on the structure and properties of rubbers

Directory of Open Access Journals (Sweden)

O. V. Karmanova

2013-01-01

Full Text Available The influence of vulcanization activator type on the properties of the compositions and elastic-strength characteristics of rubber was studied. Found that the modification of zinc oxide as the basis of actual formation curing vulcanization agents leads to an increase of vulcanization active centers, providing an increase in the velocity of rubber vulcanization and improvement of physical and mechanical rubber’s properties.

Sugarcane bagasse ash: new filler to natural rubber composite

Directory of Open Access Journals (Sweden)

Renivaldo José dos Santos

2014-12-01

Full Text Available Waste recycling has been the subject of numerous scientific researches regarding the environmental care. This paper reports the redirecting of sugarcane bagasse ash (SBA as new filler to natural rubber (NR/SBA. The NR/SBA composites were prepared using an opened cylinder mixer to incorporate the vulcanization agents and different proportions of residue (SBA. The ash contains about 70-90% of inorganic compounds, with silica (SiO2 being the main compound. The SBA incorporation improved the mechanical properties of the vulcanized rubber. Based on these results, a new use is proposed for the agro-industry organic waste to be implemented in the rubber vulcanization process, aimed at improving the rubber physical properties as well as decreasing the prices of natural rubber composites.

About the cure kinetics in natural rubber/styrene Butadiene rubber blends at 433 K

International Nuclear Information System (INIS)

Mansilla, M.A.; Marzocca, A.J.

2012-01-01

Vulcanized blends of elastomers are employed in several goods mainly to improve physical properties and reduce costs. One of the most used blends of this kind is that composed by natural rubber (NR) and styrene butadiene rubber (SBR). The cure kinetic of these blends depends mainly on the compound formulation and the cure temperature and time. The preparation method of the blends can influence the mechanical properties of the vulcanized compounds. In this work the cure kinetic at 433 K of NR/SBR blends vulcanized with the system sulfur/TBBS (N-t-butyl-2-benzothiazole sulfenamide) is analyzed in samples prepared by mechanical mixing and solution blending. The two methods produce elastomer domains of NR and SBR, which present different microstructure due to the cure level attained during vulcanization. The cure kinetics is studied by means of rheometer tests and the model proposed by Kamal and Sourour. The analysis of the cure rate is presented and is related to the structure obtained during the vulcanization process.

About the cure kinetics in natural rubber/styrene Butadiene rubber blends at 433 K

Energy Technology Data Exchange (ETDEWEB)

Mansilla, M.A., E-mail: mmansilla@df.uba.ar [Laboratorio de Polimeros y Materiales Compuestos, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon 1, C1428EGA Buenos Aires (Argentina); Marzocca, A.J. [Laboratorio de Polimeros y Materiales Compuestos, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon 1, C1428EGA Buenos Aires (Argentina)

2012-08-15

Vulcanized blends of elastomers are employed in several goods mainly to improve physical properties and reduce costs. One of the most used blends of this kind is that composed by natural rubber (NR) and styrene butadiene rubber (SBR). The cure kinetic of these blends depends mainly on the compound formulation and the cure temperature and time. The preparation method of the blends can influence the mechanical properties of the vulcanized compounds. In this work the cure kinetic at 433 K of NR/SBR blends vulcanized with the system sulfur/TBBS (N-t-butyl-2-benzothiazole sulfenamide) is analyzed in samples prepared by mechanical mixing and solution blending. The two methods produce elastomer domains of NR and SBR, which present different microstructure due to the cure level attained during vulcanization. The cure kinetics is studied by means of rheometer tests and the model proposed by Kamal and Sourour. The analysis of the cure rate is presented and is related to the structure obtained during the vulcanization process.

Gloves against mineral oils and mechanical hazards: composites of carboxylated acrylonitrile-butadiene rubber latex.

Science.gov (United States)

Krzemińska, Sylwia; Rzymski, Władysław M; Malesa, Monika; Borkowska, Urszula; Oleksy, Mariusz

2016-09-01

Resistance to permeation of noxious chemical substances should be accompanied by resistance to mechanical factors because the glove material may be torn, cut or punctured in the workplace. This study reports on glove materials, protecting against mineral oils and mechanical hazards, made of carboxylated acrylonitrile-butadiene rubber (XNBR) latex. The obtained materials were characterized by a very high resistance of the produced materials to oil permeation (breakthrough time > 480 min). The mechanical properties, and especially tear resistance, of the studied materials were improved after the addition of modified bentonite (nanofiller) to the XNBR latex mixture. The nanocomposite meets the requirements in terms of parameters characterizing tear, abrasion, cut and puncture resistance. Therefore, the developed material may be used for the production of multifunctional protective gloves.

Content of Asthmagen Natural Rubber Latex Allergens in Commercial Disposable Gloves.

Science.gov (United States)

Bittner, C; Garrido, M V; Krach, L H; Harth, V

The use of natural rubber latex (NRL) gloves in many occupations may lead to latex sensitization, allergic asthma, and skin reactions. Due to their good properties and environmental safety NRL gloves are still being used in the healthcare setting, but also in the food industry, by hairdressers, cleaners, etc. The aim of our study was to assess the protein and NRL allergen content in commercial gloves by different methods, including a new assay. Twenty commercially available NRL gloves were analyzed. Protein extraction was performed according to the international standard ASTM D-5712. Total protein content was measured with a modified Lowry method, NRL content with the CAP Inhibition Assay, the Beezhold ELISA Inhibition Assay, and an innovative ELISA with IgY-antibodies extracted from eggs of NRL-immunized hens (IgY Inhibition Assay). We found a high protein content in a range of 215.0-1304.7 μg/g in 8 out of the 20 NRL gloves. Seven of the 20 gloves were powdered, four of them with a high protein content. In gloves with high protein content, the immunological tests detected congruently high levels of NRL allergen. We conclude that a high percentage of commercially available NRL gloves still represent a risk for NRL allergy, including asthma. The modified Lowry Method allows to infer on the latex allergen content.

A novel coating strategy towards improving interfacial adhesion strength of Cu–Sn alloy coated steel with vulcanized rubber

International Nuclear Information System (INIS)

Banerjee, Atanu; Dutta, Monojit; Bysakh, Sandip; Bhowmick, Anil K.; Laha, Tapas

2014-01-01

Highlights: • We propose a double layer Cu–Sn alloy coating strategy on steel to improve adhesion. • Uniform coating with adequate penetration inside micro-roughness was observed. • XPS and GDOES study revealed improved substrate surface coverage by coating. • TEM investigation confirmed compact, uniform and micro-porosity free interface. • Peel test with vulcanized rubber confirmed improved adhesion with cohesive fracture. - Abstract: A comparative assessment in terms of uniformity, coating coverage and coating deposition mechanism has been carried out for two different types of Cu–Sn coatings on steel substrate with varying Sn composition (2–6.5 wt%) deposited via immersion technique, viz. (i) single layer Cu–Sn coating and (ii) double layer coating consisting of a thin Cu strike layer followed by a Cu–Sn layer. Coating morphology, surface coverage, coating-substrate interface, and coating composition at surface and along the depth were studied using laser confocal microscope (OLS), scanning electron microscope (SEM) coupled with energy dispersive spectroscope (EDS), glow discharge optical emission spectroscopy (GDOES), X-ray photoelectron spectroscopy (XPS) and cross-sectional transmission electron microscopy (TEM). Quantitative depth profiling using GDOES and surface compositional analysis via XPS suggested improvement in surface coverage in the case of double layer coatings. SEM-EDS and TEM analysis confirmed that the coating deposition was more uniform with sufficient coating penetration inside the deep roughness troughs resulting in compact and micro-porosity free interface for this type of coatings. Better adhesion strength with less variation in peel force and cohesive mode of fracture within the rubber was observed for the double layer coated samples during the peel test carried out on coated steel samples vulcanized with rubber. On the other hand, the single layer coated samples showed large variation in peel force with adhesive�

A novel coating strategy towards improving interfacial adhesion strength of Cu–Sn alloy coated steel with vulcanized rubber

Energy Technology Data Exchange (ETDEWEB)

Banerjee, Atanu [Tata Steel, Jamshedpur 831001 (India); Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur 721302 (India); Dutta, Monojit [Tata Steel, Jamshedpur 831001 (India); Bysakh, Sandip [Central Glass and Ceramic Research Institute, Kolkata 700032 (India); Bhowmick, Anil K. [Rubber Technology Center, Indian Institute of Technology, Kharagpur 721302 (India); Laha, Tapas, E-mail: laha@metal.iitkgp.ernet.in [Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur 721302 (India)

2014-09-15

Highlights: • We propose a double layer Cu–Sn alloy coating strategy on steel to improve adhesion. • Uniform coating with adequate penetration inside micro-roughness was observed. • XPS and GDOES study revealed improved substrate surface coverage by coating. • TEM investigation confirmed compact, uniform and micro-porosity free interface. • Peel test with vulcanized rubber confirmed improved adhesion with cohesive fracture. - Abstract: A comparative assessment in terms of uniformity, coating coverage and coating deposition mechanism has been carried out for two different types of Cu–Sn coatings on steel substrate with varying Sn composition (2–6.5 wt%) deposited via immersion technique, viz. (i) single layer Cu–Sn coating and (ii) double layer coating consisting of a thin Cu strike layer followed by a Cu–Sn layer. Coating morphology, surface coverage, coating-substrate interface, and coating composition at surface and along the depth were studied using laser confocal microscope (OLS), scanning electron microscope (SEM) coupled with energy dispersive spectroscope (EDS), glow discharge optical emission spectroscopy (GDOES), X-ray photoelectron spectroscopy (XPS) and cross-sectional transmission electron microscopy (TEM). Quantitative depth profiling using GDOES and surface compositional analysis via XPS suggested improvement in surface coverage in the case of double layer coatings. SEM-EDS and TEM analysis confirmed that the coating deposition was more uniform with sufficient coating penetration inside the deep roughness troughs resulting in compact and micro-porosity free interface for this type of coatings. Better adhesion strength with less variation in peel force and cohesive mode of fracture within the rubber was observed for the double layer coated samples during the peel test carried out on coated steel samples vulcanized with rubber. On the other hand, the single layer coated samples showed large variation in peel force with adhesive�

Effect of irradiation on the prevulcanized latex/low nitrosamines latex blends

Energy Technology Data Exchange (ETDEWEB)

Ibrahim, Pairu; Zin, Wan Manshol Wan [Malaysian Nuclear Agency, 43000 kajang, Selangor (Malaysia); Daik, Rusli [Faculty of Science and Technology, Universiti Kebangsaan Malaysia,43600 bangi, Selangor (Malaysia)

2015-09-25

Radiation Prevulcanized Natural Rubber Latex (RVNRL) was blended with Low Nitrosamines Latex (LNL) at different composition ratio. Methyl Metachrylate (MMA) was added for grafting onto the blended latex. Blended latex was subjected to gamma irradiation at various doses up to 8kGy. The mechanical properties and FTIR analysis were investigated as a function of the blended composition and irradiation dose. It was found that blending at specific ratio and gamma irradiation at specific dose led to significant improvement on the properties of the latex. The optimum mechanical properties was attained at a total blending ratio of 70% RVNRL and 30% of LNL.

Influence of zinc oxide during different stages of sulfur vulcanization. Elucidated by model compound studies

NARCIS (Netherlands)

Heideman, G.; Datta, Rabin; Noordermeer, Jacobus W.M.; van Baarle, B.

2005-01-01

The addition of zinc oxide (ZnO) as an activator for the sulfur vulcanization of rubbers enhances the vulcanization efficiency and vulcanizate properties and reduces the vulcanization time. The first part of this article deals with the reduction and optimization of the amount of ZnO. Two different

Green synthesis of colloidal silver nanoparticles using natural rubber latex extracted from Hevea brasiliensis.

Science.gov (United States)

Guidelli, Eder José; Ramos, Ana Paula; Zaniquelli, Maria Elisabete D; Baffa, Oswaldo

2011-11-01

Colloidal silver nanoparticles were synthesized by an easy green method using thermal treatment of aqueous solutions of silver nitrate and natural rubber latex (NRL) extracted from Hevea brasiliensis. The UV-Vis spectra detected the characteristic surface plasmonic absorption band around 435 nm. Both NRL and AgNO(3) contents in the reaction medium have influence in the Ag nanoparticles formation. Lower AgNO(3) concentration led to decreased particle size. The silver nanoparticles presented diameters ranging from 2 nm to 100 nm and had spherical shape. The selected area electron diffraction (SAED) patterns indicated that the silver nanoparticles have face centered cubic (fcc) crystalline structure. FTIR spectra suggest that reduction of the silver ions are facilitated by their interaction with the amine groups from ammonia, which is used for conservation of the NRL, whereas the stability of the particles results from cis-isoprene binding onto the surface of nanoparticles. Therefore natural rubber latex extracted from H. brasiliensis can be employed in the preparation of stable aqueous dispersions of silver nanoparticles acting as a dispersing and/or capping agent. Moreover, this work provides a new method for the synthesis of silver nanoparticles that is simple, easy to perform, pollutant free and inexpensive. Copyright © 2011 Elsevier B.V. All rights reserved.

Gloves against mineral oils and mechanical hazards: composites of carboxylated acrylonitrile–butadiene rubber latex

Science.gov (United States)

Krzemińska, Sylwia; Rzymski, Władysław M.; Malesa, Monika; Borkowska, Urszula; Oleksy, Mariusz

2016-01-01

Resistance to permeation of noxious chemical substances should be accompanied by resistance to mechanical factors because the glove material may be torn, cut or punctured in the workplace. This study reports on glove materials, protecting against mineral oils and mechanical hazards, made of carboxylated acrylonitrile–butadiene rubber (XNBR) latex. The obtained materials were characterized by a very high resistance of the produced materials to oil permeation (breakthrough time > 480 min). The mechanical properties, and especially tear resistance, of the studied materials were improved after the addition of modified bentonite (nanofiller) to the XNBR latex mixture. The nanocomposite meets the requirements in terms of parameters characterizing tear, abrasion, cut and puncture resistance. Therefore, the developed material may be used for the production of multifunctional protective gloves. PMID:26757889

Summary of R and D work carried out in Sri Lanka for the development of RVNRL

International Nuclear Information System (INIS)

Karunaratne, S.W.

1994-01-01

This paper discusses the advantages of radiation vulcanization of natural rubber latex and research and development carried out in this particular field. It emphasises types of centrifuge latex used, stability of this centrifuged latex, use of sensitizer, effect of leaching, antioxidants, use of low energy electron beam and training and human resources development in this field

Structural characterization of rubber from jackfruit and euphorbia as a model of natural rubber.

Science.gov (United States)

Mekkriengkrai, Dararat; Ute, Koiichi; Swiezewska, Ewa; Chojnacki, Tadeusz; Tanaka, Yasuyuki; Sakdapipanich, Jitladda T

2004-01-01

A structural study of low molecular weight rubbers from Jackfruit (Artocarpus heterophyllus) and Painted spurge (Euphorbia heterophylla) was carried out as model compounds of natural rubber from Hevea brasiliensis. The rubber content of latex from Jackfruit was 0.4-0.7%, which is very low compared with that of 30-35% in the latex from Hevea tree. The rubber from Jackfruit latex was low molecular weight with narrow unimodal molecular weight distribution (MWD), whereas that obtained from E. heterophylla showed very broad MWD. The 1H and 13C NMR analyses showed that Jackfruit rubber consists of a dimethylallyl group and two trans-isoprene units connected to a long sequence of cis-isoprene units. The alpha-terminal group of Jackfruit rubber was presumed to be composed of a phosphate group based on the presence of 1H NMR signal at 4.08 ppm corresponding to the terminal =CH-CH2OP group.

Caracterização da hipersensibilidade a luvas de látex em profissionais da odontologia = Rubber latex gloves hypersensitivities in dental workers

Directory of Open Access Journals (Sweden)

Flávia Sukekava

2007-01-01

Full Text Available As reações alérgicas ao látex vêm aumentando em profissionais da saúde e se manifestam como um incômodo local ou sintomatologia sistêmica. Para conhecer a freqüência das manifestações alérgicas nos usuários de luvas de látex foi realizada busca entre os profissionais da odontologia via aplicação de questionários. Foram aplicados 450questionários e, dentre os respondedores (140, 19% relataram manifestar reações locais ao contato com as luvas de látex e 5% reações sistêmicas a outros produtos de látex. Cerca de 2,5% declararam dermatite de contato e reações sistêmicas (anafiláticas, 1,5% apenas dermatite de contato e 1% sintomas de anafilaxia ao uso das luvas. Vinte por cento dos profissionais atenderam pacientes com alergia ao látex e 29% declararam questionar, durante a anamnese, a respeito de alergia ao látex. As reações alérgicas a luvas de látex foram freqüentes e é objeto de preocupação entre os profissionais da odontologia.Allergic reactions to natural rubber latex have increased in dental practice affecting both the professional and the patients. Allergic reactions may range from skin disease to asthma and anaphylaxis. This study aimed at determining the incidence of latex gloves allergy amongdental care workers. 450 allergy questionnaires were used to collect information on latex gloves reactions and 140 dental works answered them. Latex gloves reaction occurred in 19% of them and 5% reported allergic reactions to other latex products. 2.5% reported symptoms suggesting contact dermatitis and anaphylaxis hypersensitivities, 1.5% contact dermatitis, and 1% reported anaphylaxis symptoms when wearing them. 20% of them had patients who presented symptoms suggestive of anaphylaxis hypersensitivity to rubber gloves latex. Our study confirms that rubber latex gloves reactions are frequent among dental care workers, and dentists must be aware of the latex allergy in dental practice.

Pemanfaatan limbah kulit singkong termodifikasi alkanolamida sebagai bahan pengisi dalam produk lateks karet alam: Pengaruh waktu vulkanisasi

Directory of Open Access Journals (Sweden)

Hamidah Harahap

2015-06-01

Full Text Available The purpose of this research was to study the effect of drying time on the mechanical properties of natural rubber latex filled with cassava peel waste modified alkanolamide. Cassava peel is a waste, containing cellulose which is potential as fillers in natural rubber latex products. Cassava peel waste was dried and milled until the size of 100 mesh. Alkanolamide is one type of non-ionic surfactant which is synthesized from RBDPS (Refined Bleached Deodorized Palm Stearin and diethanolamine. Alkanolamide has polar group which can modified cassava peel waste and make strong chemical bonding with natural rubber latex. The production of natural rubber latex products was started from pre-vulcanization at 70°C until the system was cured and the chloroform number has reached number 3. Natural rubber latex was formed into films by coagulant dipping and drying method at 120°C for 10 minutes and 20 minutes. Results show that longer drying time will improve the crosslink density and tensile strength of natural rubber latex products until the addition of 15 phr cassava peel waste powder

Greenhouse Gas Emissions from Rubber Industry in Thailand

NARCIS (Netherlands)

Jawjit, W.; Kroeze, C.; Rattanapan, S.

2010-01-01

Rubber production has been taking place in Thailand for many decades. Thailand is currently the world's largest natural rubber producer. We present emissions of greenhouse gases associated with the production of fresh latex, and three primary rubber products, including concentrated latex, block

Natural rubber: leather composites

OpenAIRE

Ravichandran,K.; Natchimuthu,N.

2005-01-01

Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have ...

Antifungal activity of fluconazole-loaded natural rubber latex against Candida albicans.

Science.gov (United States)

Yonashiro Marcelino, Mônica; Azevedo Borges, Felipe; Martins Costa, Ana Flávia; de Lacorte Singulani, Junya; Ribeiro, Nathan Vinícius; Barcelos Costa-Orlandi, Caroline; Garms, Bruna Cambraia; Soares Mendes-Giannini, Maria José; Herculano, Rondinelli Donizetti; Fusco-Almeida, Ana Marisa

2018-03-01

This work aimed to produce a membrane based on fluconazole-loaded natural rubber latex (NRL), and study their interaction, drug release and antifungal susceptibility against Candida albicans. Fluconazole-loaded NRL membrane was obtained by casting method. The Fourier Transform Infrared Spectroscopy showed no modifications either in NRL or fluconazole after the incorporation. Mechanical test presented low Young's modulus and high strain, indicating the membranes have sufficient elasticity for biomedical application. The bio-membrane was able to release the drug and inhibit the growth of C. albicans as demonstrated by disk diffusion and macrodilution assays. The biomembrane was able to release fluconazole and inhibit the growth of C. albicans, representing a promising biomaterial for skin application.

Study on influence of irradiation vulcanization to silicon rubber autohesive tape's properties

International Nuclear Information System (INIS)

Chen Chun; Tang Jian; Wu Ling; Han Yingchun; Zhou Hong; Mo Yan; Fu Haijun

2006-01-01

After using 60 Co γ-ray to irradiate vulcanization silicon rubber autohesive tape, the effect of absorbed dose to the autohesive tape's tensile strength, elongation at break, autohesion and breakdown voltage strength and dose rate's effect to the autohesive tape's properties were studied. The results indicate that autohesive tape's tensile strength increases and the elongation at break decreases with the increasing dose. Under the dose of 25 kGy, the tape's autohesion increases with the increasing dose. When the dose is up to 25 kGy, the tape's autohesion achieves to the maximum, and then decreases with the increasing dose. Absorbed dose has no effect to the tape's breakdown voltage strength, and the dose rate has no effect to the autohesive tape's properties. (authors)

Latex improvement of recycled asphalt pavement

Science.gov (United States)

Drennon, C.

1982-08-01

The performance of a single unmodified milled recycled asphalt concrete was compared to milled asphalt concrete modified by addition of three types of rubber latex. Latex was added at 2, 3, 5, and 8 percent latex by weight of asphalt in the asphalt concrete. Lattices used were a styrene butadiene (SBR), a natural rubber (NR), an acrylonitrile butadiene (NBR), and four varieties of out of specification SBR lattices. Marshall tests, while indecisive, showed a modest improvement in properties of SBR and NR added material at 3 and 5 percent latex. Addition of NBR latex caused deterioration in Marshall stability and flow over that of control. Repeated load tests were run using the indirect tensile test, analyzed by the VESYS program, which computes life of pavements. Repeated load tests showed improvement in asphalt concrete life when 3 and 5 percent SBR was added. Improvement was also shown by the out of specification SBR.

NR based curred latex material reclaimed with 2,2'-dibenzamidodiphenyldisulphide in truck tyre tread compound

NARCIS (Netherlands)

Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

2006-01-01

It is observed that reclamation of natural rubber latex based rubber using 2,2'-dibenzamidodiphenyldisulphide as reclaiming agent is an optional methodology for recycling of waste latex rubber (WLR). For progressive replacement of virgin natural rubber by the reclaim, two alternatives curing system

Zinc chelates as new activators for sulphur vulcanization of acrylonitrile-butadiene elastomer

Directory of Open Access Journals (Sweden)

2009-04-01

Full Text Available The goal of this work was to apply several zinc chelates as activators for sulphur vulcanization of acrylonitrilebutadiene elastomer (NBR, in order to find alternatives for the conventionally used zinc oxide. In this article, we discuss the effects of different zinc complexes on the cure characteristics, crosslinks distribution in the elastomer network and mechanical properties of acrylonitrile-butadiene rubber. Zinc chelates seem to be good substitutes for zinc oxide as activators for sulphur vulcanization of NBR rubber, without detrimental effects on the crosslinking process and physical properties of the obtained vulcanizates. Moreover, application of zinc complexes allows to reduce the amount of zinc ions in rubber compounds by 40% compared to conventionally crosslinked vulcanizates with zinc oxide. It is a very important ecological goal since zinc oxide is classified as toxic to aquatic species and its amount in rubber products must be reduced below 2.5% at least. From a technological point of view it is a very important challenge.

Industrial application of electron beams for grafting and vulcanization

Energy Technology Data Exchange (ETDEWEB)

Makuuchi, Keizo [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

1994-12-31

The topics discussed are radiation graft polymerization; industrial application of radiation grafting - ion exchange membrane for a battery separator, ammonia adsorbent, non-flammable PE (polyethylene) foam; R and D on radiation grafting, radiation vulcanization of natural rubber.

Industrial application of electron beams for grafting and vulcanization

International Nuclear Information System (INIS)

Keizo Makuuchi

1994-01-01

The topics discussed are radiation graft polymerization; industrial application of radiation grafting - ion exchange membrane for a battery separator, ammonia adsorbent, non-flammable PE (polyethylene) foam; R and D on radiation grafting, radiation vulcanization of natural rubber

Thermal stabilities of various rubber vulcanization cured by sulfur, peroxide and gamma radiation

International Nuclear Information System (INIS)

Basfar, A.A.; Shamshad Ahmed; Abdel Aziz, M.M.

1999-01-01

Sulfur and peroxide-cured rubber vulcanizates of NR and EPDM were obtained by blending the elastomers with fillers, antioxidants and appropriate accelerators, followed by vulcanization at 150 - 160 degree C. Blends of the same elastomers with appropriate co-agents and additives were also cured by gamma radiation at 150 and 200 kGy. A comparison of the thermal stabilities of these vulcanizates prepared by different curing techniques has been made by thermogravimetric analysis (TGA), assessed on the basis of comparison of DTG peak maxima, temperature for loss of 50% mass and actual thermal curves. The comparison reveals that the sulfur-cured vulcanizates are less thermally stable than their peroxide-cured counterparts. This may be attributed to the presence of a stronger C-C bond in case of peroxide-cured vulcanizates compared to weaker C-S sub x-C bond in case of sulfur-cured vulcanizates. However, compared to peroxide-cured vulcanizates, radiation-cured formulations demonstrated much improved thermal stability. This may originate from the existence of more uniformly distributed crosslinks and the enhanced rate of crosslink formation in the radiation process as compared to peroxide curing. In all the formulations whether sulfur, peroxide or radiation-cured, the natural rubber vulcanizates were found to be thermally much inferior to the synthetic contender, EPDM. Influence of variation of the amount of co-agent and other additives on the thermal stabilities of formulations of radiation cured NR and EPDM vulcanizates was also investigated

Improvement of RVNRL film properties by adding fumed silica and hydroxy apatite

Directory of Open Access Journals (Sweden)

Adul Thiangchanya

2003-01-01

Full Text Available The effect of adding fumed silica and hydroxy apatite to Radiation Vulcanized Natural Rubber Latex (RVNRL for improving tear strength, aging properties, degradability and water-soluble protein content of rubber films has been investigated. The addition of fumed silica and hydroxy apatite in RVNRL improves tear strength and aging properties of rubber films, whereas tensile strength and degradability of rubber films were unchanged during storage at room temperature. The water-soluble protein content in rubber films was reduced by immobilization of the fumed silica and hydroxy apatite and enhanced by addition of ZnO. This may reduce allergy problems of natural rubber latex products caused by water-soluble protein. The MST of the RVNRL with fumed silica and hydroxy apatite indicated that the latex must be used within two months after mixing because of its stability.

Ciprofloxacin release using natural rubber latex membranes as carrier.

Science.gov (United States)

Dias Murbach, Heitor; Jaques Ogawa, Guilherme; Azevedo Borges, Felipe; Romeiro Miranda, Matheus Carlos; Lopes, Rute; Roberto de Barros, Natan; Guedes Mazalli, Alexandre Vinicius; Gonçalves da Silva, Rosângela; Ferreira Cinman, José Luiz; de Camargo Drago, Bruno; Donizetti Herculano, Rondinelli

2014-01-01

Natural rubber latex (NRL) from Hevea brasiliensis is easily manipulated, low cost, is of can stimulate natural angiogenesis and cellular adhesion, is a biocompatible, material and presents high mechanical resistance. Ciprofloxacin (CIP) is a synthetic antibiotic (fluoroquinolone) used in the treatment of infection at external fixation screws sites and remote infections, and this use is increasingly frequent in medical practice. The aim of this study was to develop a novel sustained delivery system for CIP based on NRL membranes and to study its delivery system behavior. CIP was found to be adsorbed on the NRL membrane, according to results of energy dispersive X-ray spectroscopy. Results show that the membrane can release CIP for up to 59.08% in 312 hours and the mechanism is due to super case II (non-Fickian). The kinetics of the drug release could be fitted with double exponential function X-ray diffraction and Fourier transform infrared (FTIR) spectroscopy shows some interaction by hydrogen bound, which influences its mechanical behavior.

Silver nanoparticles delivery system based on natural rubber latex membranes

Energy Technology Data Exchange (ETDEWEB)

Guidelli, Eder Jose, E-mail: ederguidelli@gmail.com [Universidade de Sao Paulo/FFCLRP-DF (Brazil); Kinoshita, Angela [Universidade do Sagrado Coracao (Brazil); Ramos, Ana Paula [Universidade de Sao Paulo/FFCLRP-DQ (Brazil); Baffa, Oswaldo [Universidade de Sao Paulo/FFCLRP-DF (Brazil)

2013-04-15

The search for new materials for biomedical applications is extremely important. Here, we present results on the performance of a silver nanoparticles delivery system using natural rubber latex (NRL) as the polymeric matrix. Our aim was to obtain an optimized wound dressing by combining materials with potential healing action. The synthesis of silver nanoparticles and their characterization by UV-Vis spectroscopy, transmission electron microscopy, zeta potential, dynamic light scattering, and Fourier transform infrared spectroscopy (FTIR) are depicted. The NRL membranes are good matrix for silver nanoparticles and allow for their gradual release. The release of 30 nm silver nanoparticles by the NRL membranes depends on their mass percentage in NRL membranes. The total concentration of AgNP released by the NRL membranes was calculated. The AgNP attached to the cis-isoprene molecules in the NRL matrix remain attached to the membrane ({approx}0.1 % w/w). So, only the AgNP bound to the non-rubber molecules are released. FTIR spectra suggest that non-rubber molecules, like aminoacids and proteins, associated with the serum fraction of the NRL may be attached to the surfaces of the released nanoparticles, thereby increasing the release of such molecules. The released silver nanoparticles are sterically stabilized, more stable and well dispersed. Because the serum fraction of the NRL is responsible for the angiogenic properties of the matrix, the silver nanoparticles could increment the angiogenic properties of NRL. This biomaterial has desirable properties for the fabrication of a wound dressing with potential healing action, since it combines the angiogenic and antibacterial properties of the silver nanoparticles with the increased angiogenic properties of the NRL.Graphical AbstractThe AgNP attached to the cis-isoprene molecules remain in the NRL matrix and only the AgNP bound to the non-rubber molecules (NRL serum fraction) are released. The released AgNP are

Silver nanoparticles delivery system based on natural rubber latex membranes

International Nuclear Information System (INIS)

Guidelli, Éder José; Kinoshita, Angela; Ramos, Ana Paula; Baffa, Oswaldo

2013-01-01

The search for new materials for biomedical applications is extremely important. Here, we present results on the performance of a silver nanoparticles delivery system using natural rubber latex (NRL) as the polymeric matrix. Our aim was to obtain an optimized wound dressing by combining materials with potential healing action. The synthesis of silver nanoparticles and their characterization by UV–Vis spectroscopy, transmission electron microscopy, zeta potential, dynamic light scattering, and Fourier transform infrared spectroscopy (FTIR) are depicted. The NRL membranes are good matrix for silver nanoparticles and allow for their gradual release. The release of 30 nm silver nanoparticles by the NRL membranes depends on their mass percentage in NRL membranes. The total concentration of AgNP released by the NRL membranes was calculated. The AgNP attached to the cis-isoprene molecules in the NRL matrix remain attached to the membrane (∼0.1 % w/w). So, only the AgNP bound to the non-rubber molecules are released. FTIR spectra suggest that non-rubber molecules, like aminoacids and proteins, associated with the serum fraction of the NRL may be attached to the surfaces of the released nanoparticles, thereby increasing the release of such molecules. The released silver nanoparticles are sterically stabilized, more stable and well dispersed. Because the serum fraction of the NRL is responsible for the angiogenic properties of the matrix, the silver nanoparticles could increment the angiogenic properties of NRL. This biomaterial has desirable properties for the fabrication of a wound dressing with potential healing action, since it combines the angiogenic and antibacterial properties of the silver nanoparticles with the increased angiogenic properties of the NRL.Graphical AbstractThe AgNP attached to the cis-isoprene molecules remain in the NRL matrix and only the AgNP bound to the non-rubber molecules (NRL serum fraction) are released. The released AgNP are sterically

Natural rubber latex used as drug delivery system in guided bone regeneration (GBR

Directory of Open Access Journals (Sweden)

Rondinelli Donizetti Herculano

2009-06-01

Full Text Available In this work, we propose natural rubber latex (NRL membranes as a protein delivery system. For this purpose Bovine Serum Albumin (BSA was incorporated into the latex solution for in vitro protein delivery experiments. Different polymerization temperatures were used, from -10 to 27 °C, in order to control the membrane morphology. These membranes were characterized by Scanning Electron Microscopy (SEM, Atomic Force Microscopy (AFM, as well as the Lowry Method to measure the BSA release. SEM and AFM microscopy analysis showed that the number, size and distribution of pores in NRL membranes can be varied, as well as its overall morphology. We have found that the morphology of the membrane is the predominant factor for higher protein release, compared with pore size and number of pores. Results demonstrated that the best drug-delivery system was the membrane polymerized at RT (27 °C, which does release 66% of its BSA content for up to 18 days. Our results indicate that NRLb could be used in the future as an active membrane that could accelerate bone healing in GBR.

Allergy to latex in health workers

Directory of Open Access Journals (Sweden)

Fajardo-Zapata, Álvaro L.

2015-01-01

Full Text Available Introduction: A common and growing problem in hospitals is hypersensitivity to rubber latex antigens, since many products, including gloves, are manufactured from this material, with the consequent possibility of producing allergy in persons who use them. Objective: To find out if health workers at a fourth level clinic in Bogotá, Colombia, are allergic to rubber latex, in relation to the use of gloves. Materials and methods: Descriptive, cross-sectional study of a non-probabilistic intentional-type sample in each one of four hospital units. A survey was applied to participants. Results: 16 of the 26 persons (61.5% with history of allergic processes manifested some kind of reaction when they had contact with latex gloves; the problem was more significant in the nursing personnel compared to physicians. Conclusions: The exposure to latex gloves may be generating the appearance of allergic occupational disease in health workers.

Rubber industry

Science.gov (United States)

Staszak, Maciej

2018-03-01

Following chapter presents short introductory description of rubber and rubber industry. The main problem of rubber industry is the way of the usage of spent tires. Furthermore very important group of problems arise considering the metal and nonmetal additives which are significant component of the vulcanized rubber. The key attention is dedicated to typical ways of rubber usage in utilization and recovery of metals from spent rubber materials concentrating specifically on used tires processing. The method of recovery of rare metals from rubber tires was described. The rubber debris finds widest use in the field of waste metal solutions processing. The environmental pollution caused by metals poses serious threat to humans. Several applications of the use of waste rubber debris to remove metals from environmental waters were described. Moreover, the agriculture usage of waste tire rubber debris is described, presenting systems where the rubber material can be useful as a soil replacement.

Novel in situ coordinated cerium salt/acrylonitrile-butadiene rubber composite

International Nuclear Information System (INIS)

Han, Jianjun; Lu, Haifeng; Zhang, Jie; Feng, Shengyu

2012-01-01

A novel rubber composite of acrylonitrile-butadiene rubber (NBR) filled with cerium salt particles was vulcanized via in situ coordination for the first time. The resulting materials exhibit good mechanical properties. Curing characteristics analysis, differential scanning calorimetry, X-ray photoelectron spectroscopy, tensile testing, and an equilibrium swelling method were used for the characterization of the composite. The results in this paper indicate that the composite is a kind of elastomer based on the in situ coordination crosslinking interactions between the nitrile groups (–CN) of NBR and cerium ions. The mechanical properties of vulcanized cerium salt/ NBR rubber are altered when changing the sorts of cerium salt. Moreover, these materials show good irradiation resistance because of the introduction of the cerium salt. -- Highlights: ► Cerium salts were firstly used to vulcanize the acrylonitrile-butadiene rubber. ► Cerium salts act as not only crosslink agents but also reinforcing fillers in the matrix. ► These materials show good irradiation resistance and mechanical properties at same time.

Crack Velocities in Natural Rubber.

Science.gov (United States)

1982-05-01

vulcanized natural rubber (3). The surprisingly low value for natural rubber was attributed to highly anisotropic elastic behavior at high strains...Dr. R.L. Rabie Hercules Incorporated WX-2, MS-952 Alleghany Ballistic Lab Los Alamos National Lab. P.O. Box 210 P.O. Box 1663 Washington, D.C. 21502

The evaluation of tetrabutylamonium bis(4-ethylphenylsulphonyldithiocarbimate)zincate(II) (ZNIBU) efficiency as a reclaiming agent for styrene-butadiene rubber (SBR)

International Nuclear Information System (INIS)

Moreno, Pedro H.H.; Visconte, Leila L.Y.; Pacheco, Elen B.A.V.; Tavares, Eder C.

2015-01-01

In recent years, the production of rubber waste has been reported as a serious environmental problem. The chemical structure of rubbers (crosslinked, insoluble and infusible polymers) makes its reprocessing very difficult, unlike thermoplastics. The most common methods to treat rubber waste are of thermal, mechanical and chemical nature, wherein the chemical methods the purpose is to regenerate the rubber. Early studies with tetrabutylamonium bis(4-methylphenylsulphonyldithiocarbimate)zincate(II) (ZNIBU) point to its ability as an accelerator in the rubber curing process. In this work, this zinc complex was evaluated as a chemical regeneration agent. ZNIBU was synthesized and characterized by Nuclear Magnetic Resonance ("1"3C NMR) and Fourier Transform Infrared Spectroscopy (FTIR). The mixture of virgin SBR with vulcanization ingredients was performed in a two-roll mill, and the composition was then vulcanized and molded on a hydraulic press. The synthesized ZNIBU was then mixed with the vulcanized rubber and devulcanization was observed. Finally, the devulcanized elastomeric composition was revulcanized. The revulcanization of SBR regenerated with ZNIBU led to the formation of a rubber with maximum torque near the maximum torque of the virgin vulcanized rubber. After adjusting the optimal conditions of regeneration, mechanical tests will be carried out (tensile strength, tear strength and hardness) for the specimens of both vulcanized and revulcanized rubbers in order to compare their mechanical properties. (author)

Synthesis characterization, and properties of rubber lattices; a review

International Nuclear Information System (INIS)

Khan, S.M.; Chughtai, A.; Sattar, A.

2008-01-01

Latex is a stable dispersion of polymeric material in an aqueous medium. Lattices are present in natural as well as in synthetic forms. The range of applications of latex is extensive in carpet underlay, fabric back-coating, paper and paints coatings, adhesive, binder, leather finish, floor polish, waterproof clothing, bounded fiber, pigment printing, latex thread, cement and asphalt, foam scraps binders, can closure, thickeners, box toes and shoes counters, sealant and mastics, modifiers, protein reduction, enzyme treatment and peroxide vulcanization. In this review we are presenting synthesis, characterization, properties, manufacturing and processing of latex. (author)

Pengaruh penggunaan nitril butadiene rubber dan pale crepe pada pembuatan sol karet untuk sepatu pengaman

Directory of Open Access Journals (Sweden)

Arum Yuniari

2010-06-01

Full Text Available Abstract Rubber sole for safety shoes was different on physical specification with general sole, especially on abrasion resistance and oil resistance. The objective of the study was to determine the effect of nitril butadiene rubber and pale crepe on physical properties of vulcanized rubber sole for safety shoes. Rubber sole for safety shoes was produced by blending pale crepe and nitril butadiene rubber with ratio of : 50/50; 60/40; 70/30 and 80/20 phr, respectively. Carbon black as filler was also variated with, 40 ; 50 and 60 phr. Compounding processing used two roll mill machine and vulcanized rubber sole was by using pressed use hydraulic press machine. The results showed that vulcanized rubber sole for safety shoes with good quality consist of pale crepe and NBR 80/20 phr and carbon black 40 phr, which was characterized by tensile strength 16.81 N/mm2, tear strength 11.68 N/mm, density 1.12 g/cm3, abrasion resistance 58.51 mm3, hardness 71.60 shore A, resistance to cut growth 30.000 times was 1.15 mm and oil resistance 65.44%, respectively. The quality parameters was complied with standard quality of SNI 0111 : 2009, for safety shoes from leather and vulcanized rubber sole that fulfill oil reistance parameter.

Mechanical and Physical Studies on Different Doses of Radiation Pre vulcanized Natural Rubber Latex (RVNRL)

International Nuclear Information System (INIS)

Syuhada Ramli; Sofian Ibrahim; Muhammad Saiful Omar; Mohd Noorwadi Mat Lazim; Khairul Hisyam Mohamed Yusof; Najib Mohammmad Zakey; Hafizuddin Maseri

2014-01-01

RVNRL mixture of 12 kGy (RVNRL12) and 25 kGy (RVNRL25) at different blending ratios were prepared by stirring the mixture using a magnetic stirrer RVNRL at a speed of 1-3 rpm overnight to get the dough consistency. RVNRL12 with RVNRL25 attendance at a ratio of 90:10, 80:20, 70:30, 60:40 and 50:50 investigated. The study of physical and mechanical properties of 12/ 25 blends RVNRL performed on film samples prepared by immersion method coagulant. RVNRL25 result of the addition of the mixture RVNRL12 showed an increase in tensile strength mixture ratio of 90:10 RVNRL12 / RVNRL25 and tensile strength are declining at a ratio higher RVNRL25 content. Increase the tensile strength was found to increase due to the impact of lower doses of dough RVNRL12 and RVNRL25. This shows that blending RVNRL lower doses help improve the physical properties of latex due to exposure dose exceeding the dose required RVNRL. (author)

Use of low energy accelerator for the radiation vulcanization of natural rubber latex and nitrile rubber. The battle for the sustainability and poverty alleviation

International Nuclear Information System (INIS)

Chirinos, Hugo D.; Lugao, Ademar B.

2001-01-01

The origin of the Hevea braziliensis tree was the Amazonian basin. The rubber expansion at the end of 19th century brought prosperity and determined the borders of Amazonian countries. In spite of that, the Brazilian government has failed in establishing a successful policy for improving the NR production in the jungle. This battle has been a continuous defeat against the environment as it was not possible to control the fungus Microcyclos ulei in its natural environment. The defeat was catastrophic for the population of Amazon region as they were not able to shift to other sustainable activity. As a consequence of the tack of economical options, the population had to explore all available natural resources. It has been also catastrophic for the Amazonian environment. Nevertheless, rubber plantations were successfully introduced in areas were Hevea braziliensis was not native, mainly in the southeast of Brazil. And recently, it was also introduced near marginal areas of the humid forest in the Amazon due to the absence of the fungus Microcyclos ulei. Both, extraction of wild rubber and plantation have a key role in the maintenance of the forest health as the seringueiros not only have a sustainable activity but can also play a role as soldiers of the jungle. Actually, rubber activities are not only associated to the environment but also with poverty because the activities are labor intensive, so it needs cheap labor. The poverty is unfortunately spread out in rural areas of Brazil and in the peripheral areas of the big cities. Regarding environment and poverty the dilemma is critical in the Amazonian region and is the following: the forest should be maintained healthy and protected from devastating projects and at the same time needs of the inhabitants should be considered. (author)

Influence of different curing systems on the physico-mechanical properties and stability of SBR and NR rubbers

Energy Technology Data Exchange (ETDEWEB)

Basfar, A.A. E-mail: abasfar@kacst.edu.sa; Abdel-Aziz, M.M.; Mofti, S

2002-01-01

The physical properties of radiation, sulfur and peroxide-cured styrene-butadiene rubber (SBR) and natural rubber (NR) were compared. The dependence of the mechanical properties of the radiation-vulcanized SBR and NR on the coagent concentration and radiation dose was studied. The effect of thermal aging on the mechanical properties of the different rubber formulations was discussed. The radiation-cured formulations of SBR have superior mechanical properties and thermal stability compared with those of the chemically vulcanized compounds. Whereas, the radiation-cured formulations of NR have similar mechanical properties but superior thermal stability (based on the % change in E after thermal aging), when compared with those of the sulfur-vulcanized compounds and slightly better than those of the peroxide-vulcanized compounds.

Novel in situ coordinated cerium salt/acrylonitrile-butadiene rubber composite

Energy Technology Data Exchange (ETDEWEB)

Han, Jianjun [Key Laboratory of Special Functional Aggregated Materials, Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Lu, Haifeng, E-mail: lhf@sdu.edu.cn [Key Laboratory of Special Functional Aggregated Materials, Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Zhang, Jie [Key Laboratory of Special Functional Aggregated Materials, Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Feng, Shengyu, E-mail: fsy@sdu.edu.cn [Key Laboratory of Special Functional Aggregated Materials, Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

2012-09-14

A novel rubber composite of acrylonitrile-butadiene rubber (NBR) filled with cerium salt particles was vulcanized via in situ coordination for the first time. The resulting materials exhibit good mechanical properties. Curing characteristics analysis, differential scanning calorimetry, X-ray photoelectron spectroscopy, tensile testing, and an equilibrium swelling method were used for the characterization of the composite. The results in this paper indicate that the composite is a kind of elastomer based on the in situ coordination crosslinking interactions between the nitrile groups (-CN) of NBR and cerium ions. The mechanical properties of vulcanized cerium salt/ NBR rubber are altered when changing the sorts of cerium salt. Moreover, these materials show good irradiation resistance because of the introduction of the cerium salt. -- Highlights: Black-Right-Pointing-Pointer Cerium salts were firstly used to vulcanize the acrylonitrile-butadiene rubber. Black-Right-Pointing-Pointer Cerium salts act as not only crosslink agents but also reinforcing fillers in the matrix. Black-Right-Pointing-Pointer These materials show good irradiation resistance and mechanical properties at same time.

Use of waste materials in rubber matrix

Directory of Open Access Journals (Sweden)

Pajtášová Mariana

2018-01-01

Full Text Available The presented paper deals with the use of waste materials as ecological fillers into rubber matrix. Waste materials were used as partial replacement of the commercial filler – carbon black, designated as N339. These prepared rubber compounds were characterized on the basis of the rheology and vulcanization characteristics – minimum torque (ML, maximum torque (MH, optimum time of vulcanization (t(c90, processing safety of compound (ts, rate coefficient of vulcanization (Rv. In the case of the prepared vulcanizates, physical-mechanical properties (tensile strength, tensibility and hardness and dynamic-mechanical properties (storage modulus, loss modulus, loss angle tan δ were investigated. Using the dependency of loss angle on temperature, the selected properties for tyre tread vulcanizates were evaluated, including traction on snow and ice, traction on the wet surface and rolling resistance.

Cooking time harmonization attempts for main rubbers in a truck tyre-III. Activation energy evaluation

International Nuclear Information System (INIS)

Kadima, T.H.

2011-01-01

The harmonization of optimum cooking time of rubbers containing in a tyre is became possible. This occurrence is the result of the knowledge about the respective function of each element containing in the rubber. Many kind of rubbers are been studied. The obtained results demonstrate the realization of the harmonization of optimum cooking time in different rubbers at some conditions by modifying either a kind of vulcanization accelerator or a quantity of vulcanization activator. So, accelerator or activator modifies need of energy during cooking. In this paper, we are estimated activation energy for all new rubbers obtained

[Changes in the peripheral blood of workers engaged in ethylbenzene-styrene and synthetic rubber and latex manufacture].

Science.gov (United States)

Khristeva, V

1986-01-01

A total of 67 workers were examined from the production of "Ethyl benzene-styrene" and 184 workers from the production of "Synthetic rubber and latex", as well as a control group of 59 employees. The workers from the first production are exposed to the effect of styrene, ethyl benzene and toluene. The concentrations of the substances surpass MAC, with several times, at the majority of the working places. The workers with a length of service over 10 years predominate. The workers from the second production are exposed to the combined effect of styrene and divinyl, their concentrations fluctuating from 2 to 8 times over MAC. The workers with a length of service over 10 years are 71.7%. The deviations, established in the hematological indices studied are compared with the results from a study on the workers from those productions of 6 years ago. Dynamics in the changes was established among the workers from the production of "Synthetic rubber and latex", associated with the duration of occupational exposure to styrene and divinyl. In case of a shorter length of service, the deviations are functional (reduction of peroxidase activity in granulocytes), increase of hemoglobin and hematocrit, associated with the adaptive reaction of organism. Pronounced anemic syndrome was established in a considerable number (24 workers) after an exposure of 10 years as well as lymphocytosis (35 subjects) and leukopenia (9 subjects).

Modification of Iraqi Asphalt 40/50 Properties Using Saw Dust (SD and Natural Rubber Latex

Directory of Open Access Journals (Sweden)

Rusul l M. Darwesh

2018-04-01

Full Text Available The aim of this research is to enhance the fundamental properties for asphalt binder as those spec-ifications relate to performance of asphalt mixtures. In this paper studied the effect of add (2, 4 % SD in different sizes and (3, 5 and 7% Natural rubber latex to the straight asphalt 40/50 produced from Al-Dura refinery at 160C, it was added each additive separately and then added together to asphalt in same temperature, then tested physically and mechanically according to the American Society for Testing and Materials (ASTM, the result showed largely improvement.

Diclofenac Potassium Transdermal Patches Using Natural Rubber Latex Biomembranes as Carrier

Directory of Open Access Journals (Sweden)

Natan Roberto de Barros

2015-01-01

Full Text Available The aim of this study was to design a compound transdermal patch containing diclofenac potassium (Dic-K using natural rubber latex (NRL biomembrane. The NRL from Hevea brasiliensis is easily manipulated and low cost and presents high mechanical resistance. It is a biocompatible material which can stimulate natural angiogenesis and is capable of adhering cells on its surface. Recent researches have used the NRL for Transdermal Drug Delivery Systems (TDDSs. Dic-K is used for the treatment of rheumatoid arthritis and osteoarthritis and pain relief for postoperative and posttraumatic cases, as well as inflammation and edema. Results showed that the biomembrane can release Dic-K for up to 216 hours. The kinetics of the Dic-K release could be fitted with double exponential function. X-ray diffraction and Fourier Transform Infrared (FTIR spectroscopy show some interaction by hydrogen bound. The results indicated the potential of the compound patch.

NST Quarterly. October 1996 issue

International Nuclear Information System (INIS)

1996-01-01

NST Quarterly reports current development in Nuclear Science and Technology in Malaysia. In this issue it highlights MINT activities in latex vulcanization (first RVNRL-based rubber gloves produced in Malaysia), tank floor scanning system (TAFLOSS), incineration and radiotherapeutic agent

Natural Contamination and Surface Flashover on Silicone Rubber Surface under Haze–Fog Environment

Directory of Open Access Journals (Sweden)

Ang Ren

2017-10-01

Full Text Available Anti-pollution flashover of insulator is important for power systems. In recent years, haze-fog weather occurs frequently, which makes discharge occurs easily on the insulator surface and accelerates insulation aging of insulator. In order to study the influence of haze-fog on the surface discharge of room temperature vulcanized silicone rubber, an artificial haze-fog lab was established. Based on four consecutive years of insulator contamination accumulation and atmospheric sampling in haze-fog environment, the contamination configuration appropriate for RTV-coated surface discharge test under simulation environment of haze-fog was put forward. ANSYS Maxwell was used to analyze the influence of room temperature vulcanized silicone rubber surface attachments on electric field distribution. The changes of droplet on the polluted room temperature vulcanized silicone rubber surface and the corresponding surface flashover voltage under alternating current (AC, direct current (DC positive polar (+, and DC negative polar (− power source were recorded by a high speed camera. The results are as follows: The main ion components from haze-fog atmospheric particles are NO3−, SO42−, NH4+, and Ca2+. In haze-fog environment, both the equivalent salt deposit density (ESDD and non-soluble deposit density (NSDD of insulators are higher than that under general environment. The amount of large particles on the AC transmission line is greater than that of the DC transmission line. The influence of DC polarity power source on the distribution of contamination particle size is not significant. After the deposition of haze-fog, the local conductivity of the room temperature vulcanized silicone rubber surface increased, which caused the flashover voltage reduce. Discharge is liable to occur at the triple junction point of droplet, air, and room temperature vulcanized silicone rubber surface. After the deformation or movement of droplets, a new triple junction

Graft Copolymerization of Methyl Methacrylate Monomer onto Starch and Natural Rubber Latex Initiated by Gamma Irradiation

Directory of Open Access Journals (Sweden)

S. Iskandar

2011-04-01

Full Text Available To obtain the degradable plastic, the graft copolymerization of methyl methacrylate onto starch and natural rubber latex was conducted by a simultaneous irradiation technique. Gamma-ray from cobalt-60 source was used as the initiator. The grafted copolymer of starch-polymethyl methacrylate and the grafted copolymer of natural rubber-polymethyl methacrylate were mixed in the blender, and dried it in the oven. The dried grafted copolymer mixture was then molded using hydraulic press machine. The effect of irradiation dose, composition of the grafted copolymer mixture, film forming condition and recycle effect was evaluated. The parameters observed were tensile strength, gel fraction and soil burial degradability of grafted copolymer mixture. It was found that the tensile strength of grafted copolymer mixture increased by -ray irradiation. Increasing of the grafted copolymer of natural rubber-polymethyl methacrylate content, the gel fraction and tensile strength of the grafted copolymer mixture increased. The tensile strength of the grafted copolymer mixture was increased from 18 MPa to 23 MPa after recycled (film forming reprocessed 3 times. The grafted copolymer mixture was degraded completely after soil buried for 6 months

Degrading radiation effects on properties of bromobutyl rubber compounds

Energy Technology Data Exchange (ETDEWEB)

Scagliusi, Sandra R.; Cardoso, Elisabeth C.L.; Pozenato, Cristina A.; Lugao, Ademar B., E-mail: srscagliusi@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

The understanding of chemistry involved in degradation induced radiation is becoming more and more relevant in the re-use of polymeric materials, as well in beneficial radiation uses. Degrading radiation effects have been considered from viewpoint of controlled degradation for isoprene/isobutene in rubbers for recycling purposes. Bromobutyl rubber (BIIR) is an isobutylene/isoprene copolymer comprising 1.9 to 2.1% bromine and has a lot of applications including in tires air-chambers. In this work there were evaluated gamma-irradiation effects for re-use or recycling objectives in elastomeric bromobutyl compositions irradiated at 5, 15, 25, 50, 100,150 and 200 kGy. Mechanical properties, hardness and swelling were assessed in non-vulcanized and vulcanized rubber, non-irradiated and irradiated at different doses. The major gamma radiation effect in butyl rubber is the generation of free radicals along changes in mechanical properties. Irradiation effects in bromobutyl rubber compounds were comprehensively investigated, demonstrated and discussed. (author)

Degrading radiation effects on properties of bromobutyl rubber compounds

International Nuclear Information System (INIS)

Scagliusi, Sandra R.; Cardoso, Elisabeth C.L.; Pozenato, Cristina A.; Lugao, Ademar B.

2013-01-01

The understanding of chemistry involved in degradation induced radiation is becoming more and more relevant in the re-use of polymeric materials, as well in beneficial radiation uses. Degrading radiation effects have been considered from viewpoint of controlled degradation for isoprene/isobutene in rubbers for recycling purposes. Bromobutyl rubber (BIIR) is an isobutylene/isoprene copolymer comprising 1.9 to 2.1% bromine and has a lot of applications including in tires air-chambers. In this work there were evaluated gamma-irradiation effects for re-use or recycling objectives in elastomeric bromobutyl compositions irradiated at 5, 15, 25, 50, 100,150 and 200 kGy. Mechanical properties, hardness and swelling were assessed in non-vulcanized and vulcanized rubber, non-irradiated and irradiated at different doses. The major gamma radiation effect in butyl rubber is the generation of free radicals along changes in mechanical properties. Irradiation effects in bromobutyl rubber compounds were comprehensively investigated, demonstrated and discussed. (author)

Application of recombinant latex allergens in diagnostics of occupational latex allergy

Directory of Open Access Journals (Sweden)

Ewa Nowakowska-Świrta

2015-02-01

Full Text Available Over many years, allergy to natural rubber latex has been a major problem among health care workers (HCW. The diagnosis of occupational allergy requires methods of high diagnostic accuracy in view of certification implications (e.g., a sick worker quits a job. With the development of molecular methods, the frequency of application of recombinant allergens in the diagnostics of allergic diseases continues to increase. This paper reviews the applicability of laboratory tests which use recombinant allergens in the diagnostics of occupational allergy. The diagnosis of latex allergy is based on the presence of clinical symptoms linked with exposure to latex allergens, positive skin prick tests and detection of specific IgE antibodies to latex in serum. Moreover, in some cases specific challenge tests are conducted. The analysis of literature indicates that applying the panel of recombinant latex allergens in diagnostic tests, cross-reactivity can very likely be excluded and/or sensitization can be confirmed without the need for specific challenge tests, which in case of latex allergens carries a potential risk of generalized reactions. Med Pr 2015;66(1:85–97

Evaluation of electron beam irradiation under heating process on vulcanized EPDM

International Nuclear Information System (INIS)

Gabriel, Leandro; Cardoso, Jessica R.; Moura, Eduardo; Geraldo, Aurea B.C.

2015-01-01

The Global consumption of rubber is estimated around 30.5 million tons in 2015, when it is expected an increase of 4.3% of this volume in the coming of years. This demand is mainly attributed to the production of elastomeric accessories for the automotive sector. However, the generation of this type of waste also reaches major proportions at the end of its useful life, when it is necessary to dispose the environmental liability. Rubber reprocessing is an alternative where it can be used as filler in other polymer matrices or in other types of materials. The devulcanization process is another alternative and it includes the study of methods that allow economic viability and waste reduction. Therefore, this study aims to recycle vulcanized EPDM rubber with the use of ionizing radiation. In this work we are using the electron beam irradiation process with simultaneous heating at absorbed doses from 150 kGy to 800 kGy, under high dose rate of 22.3 kGy/s on vulcanized EPDM powder and on samples about 4 mm thick. Their characterization, before and after the irradiation process, have been realized by thermal analysis and their changes have been discussed. (author)

Evaluation of electron beam irradiation under heating process on vulcanized EPDM

Energy Technology Data Exchange (ETDEWEB)

Gabriel, Leandro; Cardoso, Jessica R.; Moura, Eduardo; Geraldo, Aurea B.C., E-mail: lgabriell@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2015-07-01

The Global consumption of rubber is estimated around 30.5 million tons in 2015, when it is expected an increase of 4.3% of this volume in the coming of years. This demand is mainly attributed to the production of elastomeric accessories for the automotive sector. However, the generation of this type of waste also reaches major proportions at the end of its useful life, when it is necessary to dispose the environmental liability. Rubber reprocessing is an alternative where it can be used as filler in other polymer matrices or in other types of materials. The devulcanization process is another alternative and it includes the study of methods that allow economic viability and waste reduction. Therefore, this study aims to recycle vulcanized EPDM rubber with the use of ionizing radiation. In this work we are using the electron beam irradiation process with simultaneous heating at absorbed doses from 150 kGy to 800 kGy, under high dose rate of 22.3 kGy/s on vulcanized EPDM powder and on samples about 4 mm thick. Their characterization, before and after the irradiation process, have been realized by thermal analysis and their changes have been discussed. (author)

Synthesis, characterization and degradation behavior of admicelled polyacrylate-natural rubber

International Nuclear Information System (INIS)

Pongpilaipruet, Angkana; Magaraphan, Rathanawan

2015-01-01

In order to improve weatherability of the cured natural rubber, the novel introduction of good ozone resistant polymers such as polyacrylates (poly(methyl acrylate) (PMA) or poly(methyl methacrylate) (PMMA)) into natural rubber (NR) by admicellar polymerization was investigated in this work. The admicellar polymerization to synthesize polyacrylate layer over the surface of NR latex particles was performed with varying monomer type (PMA and PMMA) and content (50 and 100 mM). The admicelled PMMA showed higher molecular weight than PMA. Fourier transform infrared spectra of the admicellar synthesized natural rubbers exhibited characteristic peaks of those polyacrylates. Micrographs from transmission electron and field emission scanning electron microscopes (FE-SEM) revealed the coatings of PMA and PMMA over the rubber particles, suggesting a core-shell structure. Thermogravimetric analysis revealed that the admicelled rubbers not only showed an improvement in heat stability but also a single decomposition temperature. After vulcanization, FE-SEM results showed the cured admicelled rubbers had phase transformation from core-shell to phase separation (aggregate domains of polyacrylate-rich phase) with smooth interface. This agreed well to their one glass transition temperature (∼−48 °C) which indicated good miscibility between NR and each polyacrylate. The cracks generated after exposure to ozone found in the admicelled rubbers were smaller than those in NR, suggesting better ozone resistance was achieved. Increasing monomer concentration led to less cracks or much better ozone resistance. Furthermore, changes in mechanical properties after ozone exposure of the admicelled PMA-NR were less than those of the admicelled PMMA-NR (having the same shell content) and the NR, respectively. - Highlights: • We use admicellar technique to add polyacrylates to NR in form of core-shell rubber. • This core-shell structure was physically formed as seen by the phase

Synthesis, characterization and degradation behavior of admicelled polyacrylate-natural rubber

Energy Technology Data Exchange (ETDEWEB)

Pongpilaipruet, Angkana; Magaraphan, Rathanawan, E-mail: rathanawan.k@chula.ac.th

2015-06-15

In order to improve weatherability of the cured natural rubber, the novel introduction of good ozone resistant polymers such as polyacrylates (poly(methyl acrylate) (PMA) or poly(methyl methacrylate) (PMMA)) into natural rubber (NR) by admicellar polymerization was investigated in this work. The admicellar polymerization to synthesize polyacrylate layer over the surface of NR latex particles was performed with varying monomer type (PMA and PMMA) and content (50 and 100 mM). The admicelled PMMA showed higher molecular weight than PMA. Fourier transform infrared spectra of the admicellar synthesized natural rubbers exhibited characteristic peaks of those polyacrylates. Micrographs from transmission electron and field emission scanning electron microscopes (FE-SEM) revealed the coatings of PMA and PMMA over the rubber particles, suggesting a core-shell structure. Thermogravimetric analysis revealed that the admicelled rubbers not only showed an improvement in heat stability but also a single decomposition temperature. After vulcanization, FE-SEM results showed the cured admicelled rubbers had phase transformation from core-shell to phase separation (aggregate domains of polyacrylate-rich phase) with smooth interface. This agreed well to their one glass transition temperature (∼−48 °C) which indicated good miscibility between NR and each polyacrylate. The cracks generated after exposure to ozone found in the admicelled rubbers were smaller than those in NR, suggesting better ozone resistance was achieved. Increasing monomer concentration led to less cracks or much better ozone resistance. Furthermore, changes in mechanical properties after ozone exposure of the admicelled PMA-NR were less than those of the admicelled PMMA-NR (having the same shell content) and the NR, respectively. - Highlights: • We use admicellar technique to add polyacrylates to NR in form of core-shell rubber. • This core-shell structure was physically formed as seen by the phase

The Effect of Rubber Mixing Process on The Curing Characteristics of Natural Rubber

Directory of Open Access Journals (Sweden)

Abu Hasan

2013-04-01

Full Text Available This research is aimed at studying the relationship between rubber mixing processes and curing characteristics of natural rubber. The curing characteristic analysis was carried out through a natural rubber formula having been masticated and mixed, followed by curing. As many as four mastication methods were finely applied; each respected four sequences of rubber mixing process. In the first method, rubber was masticated for 5 minutes and then rubber chemicals and carbon black N 330 were  simultaneously added. In the second and the third methods, rubber was masticated for 1 minute and then carbon blacks and rubber chemicals were also simultaneously added but using different type of fillers. In the fourth method, rubber was masticated for 3 minutes and then rubber chemicals and carbon black were subsequently added. The additions of rubber chemicals and carbon blacks to the masticated rubber were distinguished by the sequence and time allocated for each mixing process. The carbon blacks were added in two stages by which 10 phr was added first and the remaining 40 phr was added later along with oil. In another method, ratios of the carbon blacks addition (as done in the first  and the second stages were 20:30, 30:20, and 40:10. The examination results showed that rubber mixing process gave an impact on the changes of curing characteristics. They were much affected by the method of carbon black addition. The mixing temperature also had an effect on both curing time and curing rate in which the higher the mixing temperature, the lower the curing time and curing rate. Vulcanization temperature also affected the curing time and curing rate in which the higher the vulcanization temperature, the lower the curing time and the higher the curing rate. Lastly, particle size of carbon black also gave an impact on the curing time and curing rate in which the smaller the particle size, the lower the curing time and the higher the curing rate.

On The compatibility and dynamic vulcanization of Pom/Nbr blends

International Nuclear Information System (INIS)

Mortezaee, M.; Naveed Family, M.H.; Mehrabzadeh, M.

2001-01-01

Polymer blends based on polyacetal butadiene rubber were prepared by melt blending technique. The mixing parameters such ad temperature, time and speed of mixing were varied to obtain a wide range of properties. The mixing parameters were optimized by evaluating the mechanical properties of the blend over a wide range of mixing conditions. The morphology of the blend indicated a two-phase structure. This study describes an attempt to improve the tensile strength of Pom/Nbr blends by means of compatibility and dynamic vulcanization. A commercial compatibility, maleic anhydride (Ma), has been used to control the phase morphology of the blend system. Dicumyl peroxide is used to dynamically vulcanize the Nbr elastomer in the blend. The tensile strength of the compatibility systems showed improvement. Dynamic vulcanization raises elastic recovery and tensile modulus of the blends, but the elongation at break decreases

Molecular identification and characterization of the pyruvate decarboxylase gene family associated with latex regeneration and stress response in rubber tree.

Science.gov (United States)

Long, Xiangyu; He, Bin; Wang, Chuang; Fang, Yongjun; Qi, Jiyan; Tang, Chaorong

2015-02-01

In plants, ethanolic fermentation occurs not only under anaerobic conditions but also under aerobic conditions, and involves carbohydrate and energy metabolism. Pyruvate decarboxylase (PDC) is the first and the key enzyme of ethanolic fermentation, which branches off the main glycolytic pathway at pyruvate. Here, four PDC genes were isolated and identified in a rubber tree, and the protein sequences they encode are very similar. The expression patterns of HbPDC4 correlated well with tapping-simulated rubber productivity in virgin rubber trees, indicating it plays an important role in regulating glycometabolism during latex regeneration. HbPDC1, HbPDC2 and HbPDC3 had striking expressional responses in leaves and bark to drought, low temperature and high temperature stresses, indicating that the HbPDC genes are involve in self-protection and defense in response to various abiotic and biotic stresses during rubber tree growth and development. To understand ethanolic fermentation in rubber trees, it will be necessary to perform an in-depth study of the regulatory pathways controlling the HbPDCs in the future. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Preparation of vinyl acetate grafted natural rubber by irradiation method

Energy Technology Data Exchange (ETDEWEB)

Porntrairat, A.; Pattamaprom, C. [Center of Excellence on Natural Rubber Technology, Department of Chemical Engineering, Faculty of Engineering, Thammasat University, Pathumthani 12120 (Thailand)

2016-03-09

Improvement in properties of natural rubber could be done by several methods. In this research, gamma radiation technique, which is simple, accurate, easy to control and clean, was applied to enhance the properties of natural rubber (NR) in latex state. The purpose of this research is to study the appropriate condition for preparing grafted natural rubber latex by using irradiation method. Vinyl acetate monomers (VAc) were grafted onto natural rubber latex (NR-g-PVAc) at 0-10 kGys by gamma radiation from Cobalt-60 source at room temperature. Physical properties of grafted natural rubber such as chloroform number, swelling ratio and gel content were measured. The VAc content of NR-g-PVAc was investigated by titration and visualized by FTIR spectroscopy. The FTIR spectra of NR-g-PVAc prepared at 0-10 kGys showed characteristic peaks of the vinyl acetate confirming that VAc could be grafted onto natural rubber molecular chains effectively under appropriate irradiation conditions. From the result, radiation grafting was found to be a useful technique for grafting of vinyl acetate onto natural rubber.

Influence of ZnO and TiO_2 particle sizes in the mechanical and dielectric properties of vulcanized rubber

International Nuclear Information System (INIS)

Gonzalez, Neudys; Custal, Maria del Angels; Rodriguez, Daniel; Riba, Jordi-Roger; Armelin, Elaine

2017-01-01

The novelty of the present study relies on the straightforward sonication of ZnO and TiO_2 and incorporation to a complex formulation of latex, with other several organic-inorganic additives that influences the cross-linking reactions. The new elastomer with particles carefully sonicated exhibit improved electrical and mechanical properties. Strong interaction among the nanoparticles and the polymer amorphous phase has been proved by means of FTIR, SEM and XRD analyses. The synergistic effect of hybrid fillers with nanometric dimensions can be used to design high-performance natural rubber nanocomposites with enhanced electrical resistance and good cross-linking degree. (author)

Radiation induced graft copolymerization of acrylonitrile on natural rubber

International Nuclear Information System (INIS)

Claramma, N.M.; Mathew, N.M.; Thomas, E.V.

1989-01-01

Acrylonitrile graft natural rubber was prepared by initiating the polymerization of acrylonitrile in natural rubber field latex using γ-rays. The reaction was carried out at different rubber-monomer concentrations and the properties of the modified rubbers were compared with those of natural rubber and nitrile rubber. (author)

Effects of carbon blacks with various structures on vulcanization and reinforcement of filled ethylene-propylene-diene rubber

Directory of Open Access Journals (Sweden)

2008-10-01

Full Text Available The effects of carbon blacks on vulcanization and mechanical properties of filled ethylene-propylene-diene rubber (EPDM are investigated, by comparing with five types of rubber-grade carbon blacks. Curing kinetics is studied by rheometer and the results indicate that the curing characteristics are influenced by combination of surface area of carbon black and sulphur content on the filler surface, because the former one enhances the physical cross-linking and the latter one introduces the additional chemical cross-linking. Both the degree of cross-linking and cure rate increase with increasing surface area and sulphur content, whereas the optimum cure time and scorch time decrease. The reinforcing nature of the carbon black is assessed from mechanical measurements. It is suggested that the surface area of carbon blacks strongly affects the physical properties of EPDM/carbon black composites. Conductive carbon black (N472 can be used as desirable reinforcing filler due to the higher degree of cross-linking of EPDM with N472 than other EPDM/carbon black composites. The morphology and distribution of particles are studied by using scanning electron microscope. The sound reinforcing ability of N472 is also supported by scanning electron microscope due to the notable dispersibility of N472 within EPDM matrix. N472 ensures the EPDM/N472 composite the most conductive sample among the five composites.

Development of radiation processes for better environment

International Nuclear Information System (INIS)

Majali, A.B.; Sabharwal, S.; Deshpande, R.S.; Sarma, K.S.S.; Bhardwaj, Y.K.; Dhanawade, B.R.

1998-01-01

The increasing population and industrialization, worldover, is placing escalating demands for the development of newer technologies that are environment friendly and minimize the pollution associated with the development. Radiation technology can be of benefit in reducing the pollution levels associated with many processes. The sulphur vulcanization method for natural rubber latex vulcanization results in the formation of considerable amounts of nitrosoamines, both in the product as well as in the factory environment. Radiation vulcanization of natural rubber latex has emerged as a commercially viable alternative to produce sulphur and nitrosoamine free rubber. A Co-60 γ-radiation based pilot plant has been functioning since April 1993 to produce vulcanized natural rubber latex (RVNRL) using acrylate monomers as sensitizer. The role of sensitizer, viz. n-butyl acrylate in the vulcanization process has been elucidated using the pulse radiolysis technique. Emission of toxic sulphur containing gases form an inevitable part of viscose-rayon process and this industry is in search of ways to reduce the associated pollution levels. The irradiation of cellulose results in cellulose activation and reduction in the degree of polymerization (DP). These effects can reduce the solvents required to dissolve the paper pulp. There is a keen interest in utilizing radiation technology in viscose rayon production. We have utilized the electron beam (EB) accelerator for reducing the degree of polymerization (DP) of paper pulp. Laboratory scale tests have been carried out to standardize the conditions for production of pulp having the desired DP by EB irradiation. The use of irradiated paper pulp can result in ∼40% reduction in the consumption of CS 2 in the process that can be beneficial in reducing the pollution associated with the process. PTFE waste can be recycled into a low molecular weight microfine powder by irradiation. An EB based process has been standardized to produce

Elastomeric Nanocomposite Based on Exfoliated Graphene Oxide and Its Characteristics without Vulcanization

OpenAIRE

Nasser Abdullah Habib; Buong Woei Chieng; Norkhairunnisa Mazlan; Umer Rashid; Robiah Yunus; Suraya Abdul Rashid

2017-01-01

Rubber nanocomposites have emerged as one of the advanced materials in recent years. The aim of this work was to homogeneously disperse graphene oxide (GO) sheets into Nitrile Butadiene Rubber (NBR) and investigate the characteristics of GO/NBR nanocomposite without vulcanization. A suitable solvent was found to dissolve dry NBR while GO was exfoliated completely in an aqueous base solution using sonication. GO was dispersed into NBR at different loadings by solution mixing to produce unvulca...

GURU v2.0: An interactive Graphical User interface to fit rheometer curves in Han's model for rubber vulcanization

Science.gov (United States)

Milani, G.; Milani, F.

A GUI software (GURU) for experimental data fitting of rheometer curves in Natural Rubber (NR) vulcanized with sulphur at different curing temperatures is presented. Experimental data are automatically loaded in GURU from an Excel spreadsheet coming from the output of the experimental machine (moving die rheometer). To fit the experimental data, the general reaction scheme proposed by Han and co-workers for NR vulcanized with sulphur is considered. From the simplified kinetic scheme adopted, a closed form solution can be found for the crosslink density, with the only limitation that the induction period is excluded from computations. Three kinetic constants must be determined in such a way to minimize the absolute error between normalized experimental data and numerical prediction. Usually, this result is achieved by means of standard least-squares data fitting. On the contrary, GURU works interactively by means of a Graphical User Interface (GUI) to minimize the error and allows an interactive calibration of the kinetic constants by means of sliders. A simple mouse click on the sliders allows the assignment of a value for each kinetic constant and a visual comparison between numerical and experimental curves. Users will thus find optimal values of the constants by means of a classic trial and error strategy. An experimental case of technical relevance is shown as benchmark.

Impacts of Different Functional Groups on the Kinetic Rates of α-Amine Ketoximesilanes Hydrolysis in the Preparation of Room Temperature Vulcanized Silicone Rubber.

Science.gov (United States)

Xu, Huihui; Liu, Zihou; Liu, Qingyang; Bei, Yiling; Zhu, Qingzeng

2018-05-13

α-Amine ketoximesilanes are proven to be effective crosslinkers in the preparation of ketone-oxime one-component room temperature vulcanized (RTV) silicone rubber without the use of toxic metal catalyst. This work aimed to investigate the hydrolysis kinetic of α-amine ketoximesilanes, which is vitally important for the preparation of RTV silicone rubber. Five kinds of α-amine ketoximesilanes, namely α-(N,N-diethyl)aminomethyltri(methylethylketoxime)silane (DEMOS), α-(N,N-di-n-butyl)aminomethyltri(methylethylketoxime)silane (DBMOS), α-(N-n-butyl)aminomethyltri(methylethylketoxime)silane (n-BMOS), α-(N-cyclohexyl)aminomethyltri(methylethylketoxime)silane (CMOS) and α-(β-aminomethyl)aminomethyltri(methylethylketoxime)silane (AEMOS), were successfully obtained and confirmed using Fourier transform infrared spectrometer (FT-IR) and hydrogen-1 nuclear magnetic resonance ( ¹H NMR). Kinetics of hydrolysis reactions were measured by FT-IR and conductivity. Our results illustrated that the kinetic constant rates ranged from 12.2 × 10 −4 s −1 to 7.6 × 10 −4 s −1 , with the decreasing order of DEMOS > n-BMOS > DBMOS > CMOS > AEMOS at the given temperature and humidity. Better performances of thermal stability could be achieved when using the α-amine ketoximesilanes as crosslinkers in the preparation of RTV silicon rubber than that of RTV silicone rubber with the use of methyltri(methylethylketoxime)silane (MOS) as a crosslinker and organic tin as a catalyst.

Epoxidação "in situ" aplicada ao látex de borracha natural "In situ" epoxidation of natural rubber latex

Directory of Open Access Journals (Sweden)

Cristiane K. Santin

2012-01-01

Full Text Available O comportamento da borracha natural na forma látex frente à reação de epoxidação foi avaliado visando estabelecer as melhores condições reacionais sem a ocorrência de reações laterais, que promovem a coagulação do látex e o desenvolvimento de um aglomerado de borracha. Grupos epóxidos foram gerados através da reação de epoxidação a partir da formação in situ do ácido perfórmico. As amostras foram caracterizadas qualitativamente por espectroscopia de infravermelho (FTIR e o grau de modificação determinado por ressonância magnética nuclear de hidrogênio (1H-RMN. Análises de calorimetria exploratória diferencial (DSC demonstraram que a mobilidade da cadeia polimérica foi influenciada pela presença de grupos epóxidos, com aumento linear na temperatura de transição vítrea (Tg. Os resultados indicaram que a epoxidação do látex de borracha natural, sem a ocorrência de reações laterais, é possível e dependente das condições reacionais.Natural rubber latex was submitted to epoxidation reaction to establish the best reaction conditions without the occurrence of side reactions, which promote coagulation of the latex and development of an agglomerate of rubber. Epoxy groups were produced by in situ epoxidation with formic acid and hydrogen peroxide. The samples were characterized qualitatively by Fourier Transform Infrared (FTIR analysis and the degree of modification determined by Hydrogen Nuclear Magnetic Resonance Spectroscopy (1H-NMR analysis. A linear increase in the glass transition temperature (Tg was observed. The results show that the epoxidation of natural rubber latex is possible and depends on the reaction conditions.

Characteristic of natural rubber latex-methyl metha-crylate copolymer in mineral lubricant base oil

International Nuclear Information System (INIS)

Meri Suhartini; Rahmawati

2010-01-01

Natural rubber latex-methyl methacrylate copolymer was diluted in xylene, then diluted in four types of lubricant base oil with concentrations of 0.25%, 1%, 5%, and 10%. The mixed solutions were analyzed to obtain kinematics viscosity, viscosity index, density, ash content, metal content, flash point, shear stability and total alkali number. The viscosity index of sample, increased by adding the copolymer solution. The results showed that lubricant base oil of High Viscosity index (HVI) 60 and mixed HVI 60: HVI 650 gave optimum viscosity index. The higher concentration of polymer added into base lubricant oil, the higher viscosity index obtained. The shear stability test showed that the kinematics viscosity of sample decreased 6.5% after 60 minutes of treatment test. (author)

An evidence-based approach to medication preparation for the surgical patient at risk for latex allergy: is it time to stop being stopper poppers?

Science.gov (United States)

Heitz, James W; Bader, Stephen O

2010-09-01

The prevalence of latex allergy is increasing in surgical patient populations. Avoidance of exposure to the allergen is essential to minimizing perioperative complications in patients suspected to be at risk. Natural rubber latex has historically been ubiquitous in medical devices containing rubber. In 1998, the Food and Drug Administration (FDA) began to require the labeling of medical devices made from natural rubber latex; since that time substantial progress has been made in identifying latex-free alternatives. However, the rubber stoppers commonly found in pharmaceutical vial closures are exempt from FDA labeling requirements. Examination of the clinical and basic science literature regarding pharmaceutical vial closures supports limiting the rubber stopper to a single needle puncture as a safer practice, with the caveat that no strategy exists for the complete elimination of risk as long as stoppers made from natural rubber latex are used in pharmaceutical vials intended for human use. Copyright © 2010 Elsevier Inc. All rights reserved.

CDNA library from the Latex of Hevea brasiliensis

Directory of Open Access Journals (Sweden)

Wilaiwan Chotigeat

2010-12-01

Full Text Available Latex from Hevea brasiliensis contains 30-50% (w/w of natural rubber (cis-1,4-polyisoprene, the important rawmaterial for many rubber industries. We have constructed a cDNA library from the latex of H. brasiliensis to investigate theexpressed genes and molecular events in the latex. We analyzed 412 expressed sequence tags (ESTs. More than 90% of theEST clones showed homology to previously described sequences in public databases. Functional classification of the ESTsshowed that the largest category were proteins of unknown function (30.1%, 11.4% of ESTs encoded for rubber synthesisrelatedproteins (RS and 8.5% for defense or stress related proteins (DS. Those with no significant homology to knownsequences (NSH accounted for 8.7%, primary metabolism (PM and gene expression and RNA metabolism were 7.8% and6.6%, respectively. Other categories included, protein synthesis-related proteins (6.6%, chromatin and DNA metabolism(CDM 3.9%, energy metabolism (EM 3.4%, cellular transport (CT 3.2%, cell structure (CS 3.2%, signal transduction (ST2.2%, secondary metabolism (SM 1.7%, protein fate (PF 2.2%, and reproductive proteins (RP 0.7%.

Natural rubber: leather composites

Directory of Open Access Journals (Sweden)

K. Ravichandran

2005-06-01

Full Text Available Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have been discussed. Use of chrome leather particles has been found to improve the consumption of scrap rubber powder in natural rubber formulations. Polymer composites based on leather wastes as fillers are reported to be useful for many applications such as in construction materials, automobile interior moldings, heat and sound insulating boards, shoe soles, flooring materials and moldings with good anti-static properties, air permeability and good appearances.

The rapid determination of volatile fatty acid number in para rubber latex using fourier transform-near infrared spectroscopy based on quantification and discrimination model

Directory of Open Access Journals (Sweden)

Sureeporn Narongwongwattana

2015-09-01

Full Text Available Volatile Fatty Acid number (VFA no. is one of the parameters indicating the state of quality of Para rubber latex at that particular time. Most factories analyze this parameter using standard analytical method as in ISO 506:1992(E. Nevertheless, this procedure is complicated, chemical and time consuming, as well as skilled analyst required. Therefore, near infrared (NIR spectroscopy which is rapid, accurate and nonchemicals method was applied to determine the VFA no. in field latex and concentrated latex based on quantification and discriminant model. The best calibration equation was obtained from standard normal variate (SNV spectra in the region of 6109.7–5770.3, 4613.1–4242.9 cm-1 with R = 0.832, SECV = 0.036 and no bias. From the performance check, statistically it was found that SECV and bias were low enough for practical acceptance and the predicted VFA no. was not different significantly from actual VFA no. at 95% confidence intervals. In addition, discriminant model was developed to separate good quality latex from the deteriorated latex using VFA no. at 0.06 as standard as in ISO 2004:2010(E. The discriminant model can be used to screen the latex with overall accuracy of 91.86% in validation set.

Lignocellulosic fiber reinforced rubber composites

CSIR Research Space (South Africa)

Jacob John, Maya

2009-04-01

Full Text Available Natural Rubber (NR) is a naturally occurring elastomeric polymer of isoprene (2-methyl-1,3-butadiene). It can be extracted from latex of only one kind of tree, the Hevea braziliensis. Hevea rubber is produced in many tropical regions of Southeast...

Radiation Vulcanization of Polymeric Blends Based on Ethylene Propylene Diene Monomer Rubber/ Waste Materials in Presence of Different Additives

International Nuclear Information System (INIS)

MOHAMED, R.M.

2015-01-01

In this investigation, the mechanical blending technique was applied for preparation of elastomeric blend of ethylene propylene diene monomer rubber (EPDM)and nitrile butadiene rubber (NBR) having a fixed ratio of (50/50) by weight. The prepared blend of EPDM/NBR (50/50) was used as a rubber matrix to be loaded with waste materials, namely rice husk (RH) as a natural waste filler and then with ground tire rubber (GTR) as an artificial one. The degree of loading varied from 5 p hr to 20 p hr. Ionizing radiation, namely ,gamma rays were applied for inducing vulcanization of prepared and loaded rubber blends, in the range from 5 kGy to 250 kGy. Different properties of prepared composites were followed up as a function of degree of loading with the waste material and dose of irradiation. The mechanical properties, namely tensile strength and elongation at break percent of the composites slightly decreased as the filler loading increased over the whole range of irradiation .Tensile modulus and hardness, on the other hand, showed an opposite trend, i.e. the increased. Other properties, namely physical, thermal and morphological confirmed the mechanical ones. Obtained results were affiliated with lack of interface adhesion between the waste materials and the rubber matrix elastomers. The lack of interface adhesion was improved by filling the composite with a limited content, up to 7 p hr, of the compatibilizer, namely, maleic anhydride (MAH). Measurements of different properties was carried out for composite loaded with 10 p hr of waste material. It has been found that the tensile properties were significantly improved with addition of the compatibilizing agent Further and significant improvement was attained in properties of prepared later composite by its loading with 40 p hr of either HAF- carbon black or Hisil as reinforcing fillers that participates in chemical as well as physical bonding. Similarly and lastly 8 p hr of N, N- methylene di acrylamide (MDA) were loaded

Influence of ZnO and TiO{sub 2} particle sizes in the mechanical and dielectric properties of vulcanized rubber

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, Neudys; Custal, Maria del Angels; Rodriguez, Daniel [Sicame Company, Barcelona (Spain); Riba, Jordi-Roger [Departament d' Enginyeria Eletrica, Universitat Politecnica de Catalunya, Terrasssa (Spain); Armelin, Elaine, E-mail: elaine.armelin@upc.edu [Universitat Politecnica de Catalunya, Barcelona (Spain)

2017-07-15

The novelty of the present study relies on the straightforward sonication of ZnO and TiO{sub 2} and incorporation to a complex formulation of latex, with other several organic-inorganic additives that influences the cross-linking reactions. The new elastomer with particles carefully sonicated exhibit improved electrical and mechanical properties. Strong interaction among the nanoparticles and the polymer amorphous phase has been proved by means of FTIR, SEM and XRD analyses. The synergistic effect of hybrid fillers with nanometric dimensions can be used to design high-performance natural rubber nanocomposites with enhanced electrical resistance and good cross-linking degree. (author)

Pengaruh Konsentrasi Amonium Laurat Terhadap Kekuatan Tarik dan Kemuluran serta Ketahanan Sobek Film Lateks Karet Alam

OpenAIRE

Hussudur, Misbah

2011-01-01

An investigation about the influence of ammonium laurate concentration to natural rubber latex film was obtained using the immersion method. The variation of ammonium laurate concentration was used 0%; 0,05%; 0,07%; and 0,09% with vulcanization time used was for 30 minutes and vulcanization temperature was used 1000C. The physics characteristic witch analized were tensile strength, elongation and tear strength and the structure of resulting surfaces were tested with analysis of SEM. rom this ...

Study on the structure-properties relationship of natural rubber/SiO2 composites modified by a novel multi-functional rubber agent

Directory of Open Access Journals (Sweden)

S. Y. Yang

2014-06-01

Full Text Available Vulcanization property and structure-properties relationship of natural rubber (NR/silica (SiO2 composites modified by a novel multi-functional rubber agent, N-phenyl- N'-(γ-triethoxysilane-propyl thiourea (STU, are investigated in detail. Results from the infrared spectroscopy (IR and X-ray photoelectron spectroscopy (XPS show that STU can graft to the surface of SiO2 under heating, resulting in a fine-dispersed structure in the rubber matrix without the connectivity of SiO2 particles as revealed by transmission electron microscopy (TEM. This modification effect reduces the block vulcanization effect of SiO2 for NR/SiO2/STU compounds under vulcanization process evidently. The 400% modulus and tensile strength of NR/SiO2/STU composites are much higher than that of NR/SiO2/TU composites, although the crystal index at the stretching ratio of 4 and crosslinking densities of NR/SiO2 composites are almost the same at the same dosage of SiO2. Consequently, a structure-property relationship of NR/SiO2/STU composites is proposed that the silane chain of STU can entangle with NR molecular chains to form an interfacial region, which is in accordance with the experimental observations quite well.

GURU v2.0: An interactive Graphical User interface to fit rheometer curves in Han’s model for rubber vulcanization

Directory of Open Access Journals (Sweden)

G. Milani

2016-01-01

Full Text Available A GUI software (GURU for experimental data fitting of rheometer curves in Natural Rubber (NR vulcanized with sulphur at different curing temperatures is presented. Experimental data are automatically loaded in GURU from an Excel spreadsheet coming from the output of the experimental machine (moving die rheometer. To fit the experimental data, the general reaction scheme proposed by Han and co-workers for NR vulcanized with sulphur is considered. From the simplified kinetic scheme adopted, a closed form solution can be found for the crosslink density, with the only limitation that the induction period is excluded from computations. Three kinetic constants must be determined in such a way to minimize the absolute error between normalized experimental data and numerical prediction. Usually, this result is achieved by means of standard least-squares data fitting. On the contrary, GURU works interactively by means of a Graphical User Interface (GUI to minimize the error and allows an interactive calibration of the kinetic constants by means of sliders. A simple mouse click on the sliders allows the assignment of a value for each kinetic constant and a visual comparison between numerical and experimental curves. Users will thus find optimal values of the constants by means of a classic trial and error strategy. An experimental case of technical relevance is shown as benchmark.

Syntheses, spectroscopic characterization, crystal structure and natural rubber vulcanization activity of new disulfides derived from sulfonyldithiocarbimates

Science.gov (United States)

Alves, Leandro de Carvalho; Rubinger, Mayura Marques Magalhães; Tavares, Eder do Couto; Janczak, Jan; Pacheco, Elen Beatriz Acordi Vasques; Visconte, Leila Lea Yuan; Oliveira, Marcelo Ribeiro Leite

2013-09-01

The compounds (Bu4N)2[(4-RC6H4SO2NCS2)2] [Bu4N = tetrabutylammonium cation; R = H (1), F (2), Cl (3) and Br (4)] and (Ph4P)2[(4-RC6H4SO2NCS2)2]ṡH2O [Ph4P = tetraphenylphosphonium cation and R = I (5)] were synthesized by the reaction of the potassium dithiocarbimates (4-RC6H4SO2NCS2K2ṡ2H2O) with I2 and Bu4NBr or Ph4PCl. The IR data were consistent with the formation of the dithiocarbimatodisulfides anions. The NMR spectra showed the expected signals for the cations and anions in a 2:1 proportion. The structures of compounds 1-5 were determined by the single crystal X-ray diffraction. The compounds 2, 3 and 4 are isostructural and crystallise in the centrosymmetric space group C2/c of the monoclinic system. Compound 1 crystallises in the monoclinic system in the space group of P21/n and the compound 5 crystallises in the centrosymmetric space group P-1 of the triclinic system. The complex anions of compounds 2, 3 and 4 exhibit similar conformations having twofold symmetry, while in 1 and 5 the anions exhibit C1 symmetry. The activity of the new compounds in the vulcanization of the natural rubber was evaluated and compared to the commercial accelerators ZDMC, TBBS and TMTD. These studies confirm that the sulfonyldithiocarbimato disulfides anions are new vulcanization accelerators, being slower than the commercial accelerators, but producing a greater degree of crosslinking, and scorch time values compatible with good processing safety for industrial applications. The mechanical properties, stress and tear resistances were determined and compared to those obtained with the commercial accelerators.

Application of gamma irradiation for incorporation of rubber powder in the formulations of EPDM and natural rubber

International Nuclear Information System (INIS)

Kiyan, Ludmila Y.P.; Parra, Duclerc Fernandes; Lugao, Ademar Benevolo

2013-01-01

The objective of this work was to study the behavior of the recycling of rubber burrs in form of powder, of the rubber industry from EPDM rubber powder and natural rubber with SBR. The rubber powder was irradiated and reused in rubber artifacts formulations for classical vulcanization. The processed material was irradiated using a 60 Co source in doses of 50, 100, 150 and 200 kGy and a dose rate of 5 kGy s-1 at room temperature. The radiation created devulcanization active sites for subsequent integration of the material (rubber powder) in formulations of commercial use. The processes were compared and their products characterized by analytical methods of the physical properties such as strength and elongation. Satisfactory results were found, noting a major spin-off of EPDM chain demonstrated by increased elongation

PRELIMINARY RESULTS IN SYNCHROTRON X-RAY DIFFRACTION MEASUREMENTS OF RUBBER COMPOSITES STRUCTURE BEFORE AND AFTER EXPOSURE TO HYDROGEN

Directory of Open Access Journals (Sweden)

Francesca Cosmi

2011-05-01

Full Text Available In future years, fuel cells are expected to represent a promising technology as a source of heat and electricity in buildings and of electrical power for vehicles, since fossil fuels are exhausting and significantly degrade air quality. It is well known that, when exposed to a hydrogen environment, hydrogen embrittlerment may affect materials such as iron and steel. But these are not the only materials that are used for hydrogen equipment. In particular, the rubber materials used for O–rings that seal high pressure hydrogen gas equipment show problems of internal fracture, called blister fracture, when the gas is rapidly decompressed. As many different kinds of fillers can be used, in this work we started to investigate the influence of the type of filler on the rubber composites structure, by means of X-ray diffraction measurements performed at the Elettra synchrotron radiation facility in Trieste. In this preliminary study, three kinds of samples were analyzed before and after exposure to hydrogen: Sulphur vulcanized EPDM, Peroxide vulcanized EPDM and Sulphur vulcanized NBR. While Peroxide vulcanized samples did not show significant differences in the diffraction pattern, changes could be detected in the cristalline form of Sulfure vulcanized rubber.

Study of properties of chloroprene rubber devulcanizate by radiation in microwave

International Nuclear Information System (INIS)

Scagliusi, Sandra R.; Araujo, Sumair G.; Landini, Liliane; Lugao, Ademar B.

2009-01-01

Among the vulcanized elastomers, the chloroprene rubber (DuPont Neoprene R - generic name) possesses a good performance, being one of the most used in the current days. However, this kind of polymer causes a serious environmental problem if it is not reprocessed or recycled. A worldwide method that has been used and that is an important tool in the rubber devulcanization is microwave irradiation at high temperature Elastomer waste may be devulcanized without depolymerization and allows a new vulcanization into a product having physical properties essentially equivalent to the original vulcanized. In this work, the chloroprene samples were irradiated in microwave generator equipment with 2,450 MHz (frequency) and 1,000 W to 3,000 W (power). The properties of samples (according to ASTM standards) were analyzed before and after irradiation. The degraded material after irradiation will be tested for re-use. (author)

their use as Accelerator in Curing Process of Rubber Compounds

Directory of Open Access Journals (Sweden)

S. taghvaee

2007-06-01

Full Text Available In some special cases, rubber compounds with high amounts of unsaturated elastomer are recommended with organic sulfur donors instead of mineral sulfurs. In this condition, activated sulfur is produced in situ and curingprocess is facilitated without accelerators. Organic sulfur donor compounds have low thermal stability and in the vulcanization temperature produce free and activated sulfurs. The advantages of these compounds are:1. High effectiveness of curing agent in low quantities in rubber compounds manufacturing.2. Producing activated sulfurs in controlled condition and avoiding the over curing of rubber compounds.In this report the novel synthesis of some derivatives of diamino-disulfides which can be applied as sulfur donors in vulcanization of special rubber compounds is introduced. The key process is reaction of sulfurmonochloride with amines in petroleum ether as solvent in low temperature. Dithio-dimorpholine(DTDM, dithio-dipipyridyl (DTDP, dithio-bis dibutylamine (DTBDB and dithio-bisdiisopropyl amine (DTBDI were prepared according to this method. All products thus obtained were characterized by 1H and 13C-NMR spectroscopies. The effects of accelerating and sulfur donoring of all prepared agents were detected in rubber compounds with natural and synthetic rubber bases. All physical, chemical, reological and mechanical properties of rubber compounds based on prepared sulfur donors were characterized.

Study on the production of kanvas shoes adhesive from natural rubber latex grafted with methyl methacrylate (NRL-g PMMA) copolymer

International Nuclear Information System (INIS)

Utama, Marga; Sudirman; Setyowati, Penny

2002-01-01

The optimation condition of radiation copolymerization of MMA into natural rubber latex at the doses of radiation : 5; 7.5 and 10 kGy with concentration of MMA 25; 50; 75; and 100 phr (Part Hundred Ratio of Rubber) expectially and optimazation condition of the adhesive process all the production of canvas shoes have been carried out. The properties of NRL-g-MMA and its rubber such as total solid contain, viscosity, pH, modulus, tensile, strenght, hardnes, elongation at break, and adhesive strenght for producting canvas shoes where evaluated. The at adhesive results show that NRL-g-MMA with the 75 phr of MMA and iradiation dose 5 kGy is adhesive will good stability during storage. The adhesive strenght of shoes its 16-18 N/6mm, more here than SNI 1-0172-1987 with the value 10N/6mm. Besic there is a tendency that adhesive strengt of product shoes at rome temperature (30-50 o C). stronger than at high temperature (100 o C)

Research Progress in Graphene/Rubber Conducting Nanocomposites

Directory of Open Access Journals (Sweden)

DONG Hui-min

2017-03-01

Full Text Available The conductive mechanism of graphene/rubber nanocomposites was introduced.Advances in the synthesis and properties of graphene and its derivatives, modifications of graphene, along with its hybrid fillers, as well as fabrication of related rubber conducting nanocomposites were reviewed.Many factors affecting the electrical properties, such as fabrication method, vulcanization, temperature, pressure, frequency and media etc. were also summarized.It was pointed out that the further research should be focused on multi-component graphene/rubber nanocomposites and its double percolation phenomenon.

Natural rubber producing plants: An overview | Venkatachalam ...

African Journals Online (AJOL)

... Hevea and also other natural rubber producing species for alternative source of latex production in the near future. Keywords: Alternative rubber sources, biotechnology, breeding, Hevea brasiliensis, Parthenium argentatum, Taraxacum koksaghyz, Ficus bengalensis, Lactuca serriola. African Journal of Biotechnology Vol.

Thermoplastic Elastomers From Chemically or Irradiation Activated Polyolefin Wastes and Ground Tyre Rubber

International Nuclear Information System (INIS)

Tolstov, A.M.; Grigoryeva, A.L.; Bardash, O.P.

2005-01-01

Thermoplastic elastomers (TPE) are known as materials with unique combination of elastomeric properties and thermo plasticity. Among the TPE of different type the polymer blends of thermoplastics and rubbers are the most commonly used. Recently a very effective technology of dynamic vulcanization of rubber component inside thermoplastic matrix has been developed. As a result of rubber vulcanization and dispersion inside thermoplastic the new type of TPE so-called thermoplastic dynamic vulcanizations (TPV) are obtained. In our work we have applied the technology of dynamic vulcanization for recycled components (PP, HDPE, GTR). It has appeared that such components are not mixed well and the resulting TPV have poor mechanical properties. To solve a problem of poor compatibility of the components used we carried out a pre-modification (functionalization) of the component surfaces by gamma-irradiation or by chemically or gamma-irradiation induced grafting of reactive monomers. Both the polyolefin (HDPE) and GTR were functionalized before mixing. The monomers were selected by such a way that being grafted to be able to react to each other in interface during the components blending. For example, we used maleic anhydride and acrylamide. The effect of better compatibility has appeared in higher tensile characteristics of TPV synthesized

Incidence of latex harvesting technologies on agronomic and ...

African Journals Online (AJOL)

Incidence of latex harvesting technologies on agronomic and physiological parameters and profitability of some rapid metabolic class clones of rubber tree ( Hevea brasiliensis ) in southwestern Côte d'Ivoire.

New Insights into the Relationship Between Network Structure and Strain Induced Crystallization in Unvolcanized Natural Rubber by Synchrotron X-ray Diffraction

International Nuclear Information System (INIS)

Toki, S.; Hsiao, B.; Amnuaypornsri, S.; Sakdapipanich, J.

2009-01-01

The relationship between the network structure and strain-induced crystallization in un-vulcanized as well as vulcanized natural rubbers (NR) and synthetic poly-isoprene rubbers (IR) was investigated via synchrotron wide-angle X-ray diffraction (WAXD) technique. It was found that the presence of a naturally occurring network structure formed by natural components in un-vulcanized NR significantly facilitates strain-induced crystallization and enhances modulus and tensile strength. The stress-strain relation in vulcanized NR is due to the combined effect of chemical and naturally occurring networks. The weakness of naturally occurring network against stress and temperature suggests that vulcanized NR has additional relaxation mechanism due to naturally occurring network. The superior mechanical properties in NR compared with IR are mainly due to the existence of naturally occurring network structure.

Study of Antibacterial Activity and Bacteriology of Latex from Asclepias syriaca L

Science.gov (United States)

McCay, Steven; Mahlberg, Paul

1973-01-01

Whole and fractionated latex of Asclepias syriaca was tested for antimicrobial or growth-promoting activity with 16 genera and species of bacteria. Latex and extracted fractions (distilled water, acetic acid, sodium bicarbonate, sulfuric acid, and ethyl ether) possessed no detectable antimicrobial activity. Comparison of growth curves of selected bacteria incubated with serum and rubber fractions, as well as controls, revealed no detectable inhibition of growth, except for a slight inhibitory response to autoclaved serum. Most bacteria were capable of utilizing latex for a substrate as indicated by the increased growth rate in the exponential phase. The stationary phase was entered simultaneously by both the treated cultures and the controls. Various bacteria cultured in a litmus latex mixture yielded populations which ranged from <104 organisms/ml for Lactobacillus casei, Staphylococcus aureus and Micrococcus lysodeikticus to 1.1 × 1010 organisms/ml for Clostridium acetobutylicum. Whole latex, as well as the serum and rubber fractions, support the growth of various bacteria, but under field conditions there is no evidence for systemic infection of this type of cell by bacteria. PMID:4790590

Study of properties of chloroprene rubber devulcanizate by radiation in microwave

Energy Technology Data Exchange (ETDEWEB)

Scagliusi, Sandra R.; Araujo, Sumair G.; Landini, Liliane; Lugao, Ademar B., E-mail: scagliusi@usp.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2009-07-01

Among the vulcanized elastomers, the chloroprene rubber (DuPont Neoprene{sup R} - generic name) possesses a good performance, being one of the most used in the current days. However, this kind of polymer causes a serious environmental problem if it is not reprocessed or recycled. A worldwide method that has been used and that is an important tool in the rubber devulcanization is microwave irradiation at high temperature Elastomer waste may be devulcanized without depolymerization and allows a new vulcanization into a product having physical properties essentially equivalent to the original vulcanized. In this work, the chloroprene samples were irradiated in microwave generator equipment with 2,450 MHz (frequency) and 1,000 W to 3,000 W (power). The properties of samples (according to ASTM standards) were analyzed before and after irradiation. The degraded material after irradiation will be tested for re-use. (author)

Properties of tire rubber with zinc-containing technological additives

Directory of Open Access Journals (Sweden)

S. N. Kayushnikov

2017-01-01

Full Text Available In this paper, we studied the influence of zinc-containing technological additives on partial replacement of zinc oxide and stearic acid on deformation-strength and performance properties of tire elastomeric compositions based on polyisoprene rubber and combination of oil-filled butadiene-styrene and polybutadiene rubbers. It was revealed that partial replacement of zinc oxide and stearic acid with zinc-containing technological additives does not significantly affect the basic physico-mechanical properties of rubbers based on synthetic rubbers of general use. It was determined that the introduction of zinc-containing technological additives SCC2 in combination with zinc oxide in all the studied ratios and SCC3 in combination with zinc oxide in 4: 1 and 3: 1 ratios leads to increase (up to 10.4% of the resistance of these rubbers under the action of temperature-force fields, which is probably due to a more even distribution of polar components of curing system in non-polar elastomeric matrix, as well as the type of cross-links formed during vulcanization under the action of surface-active additives. It has been found that the introduction of zinc-containing additives into the elastomeric compositions based on SRMS-30 ARKM-15 + SRD in combination with zinc oxide leads to increase to 6.3% of wear resistance of rubbers, which may be due to a lower defectiveness of vulcanization structure of these rubbers, concentration of stress centers in the material. For rubbers based on SRI-3, preservation of bond strength of rubber with a textile cord at a sufficiently high level is shown.

Devulcanization of Waste Tire Rubber Using Amine Based Solvents and Ultrasonic Energy

OpenAIRE

Walvekar Rashmi; Afiq Zulkefly Mohammad.; Ramarad Suganti; Khalid Siddiqui

2018-01-01

This research project focuses on an alternative pathway of devulcanizing waste tire rubber by using amine based chemicals. Waste tire rubbers are known to be as toxic, non-degradable material due to their vulcanized crosslink carbon structure, and disposing of such waste could impose hazardous impacts on the environment. The current rubber recycling methods that are practiced today are rather uneconomical, non-environmentally friendly, and also producing recycled rubber with low quality due t...

Finite Element Analysis of Simple Rectangular Microstrip Sensor for Determination Moisture Content of Hevea Rubber Latex

Science.gov (United States)

Yahaya, NZ; Ramli, MR; Razak, NNANA; Abbas, Z.

2018-04-01

The Finite Element Method, FEM has been successfully used to model a simple rectangular microstrip sensor to determine the moisture content of Hevea rubber latex. The FEM simulation of sensor and samples was implemented by using COMSOL Multiphysics software. The simulation includes the calculation of magnitude and phase of reflection coefficient and was compared to analytical method. The results show a good agreement in finding the magnitude and phase of reflection coefficient when compared with analytical results. Field distributions of both the unloaded sensor as well as the sensor loaded with different percentages of moisture content were visualized using FEM in conjunction with COMSOL software. The higher the amount of moisture content in the sample the more the electric loops were observed.

Preparation of sulfonic acid-containing rubbers from natural rubber vulcanizates

Science.gov (United States)

Poonsawat, Worapong; Poompradub, Sirilux; Ngamcharussrivichai, Chawalit

2014-06-01

In this work, a series of sulfonic acid-containing rubbers were prepared by aqueous phase oxidation of natural rubber vulcanizates in the presence of hydrogen peroxide (H2O2) and formic acid (HCOOH). The starting vulcanizates were neatly prepared via an efficient vulcanization (EV) system by varying mass ratio of N-cyclohexyl-2-benzothiazole sulfonamide (CBS), as an accelerator, to sulfur. The oxidation conditions were controlled at the molar ratio of H2O2: HCOOH = 1:1, the concentration of H2O2 = 15 wt.%, the temperature = 50 °C, and the reaction time = 3 h. The rubber materials before and after the oxidation were characterized for their physicochemical properties by using Fourier transform infrared spectroscopy, bomb calorimetry, acid-base titration and swelling measurements. The results indicated the presence of sulfonic acid group in the oxidized rubbers, generated by the oxidative cleaves of sulfide crosslinks in the rubber vulcanizates. The oxidation decreased the sulfur content of the rubber in which the level of sulfur loss was determined by the CBS/sulfur ratio. Moreover, the acidity of the oxidized products was correlated with the amount of sulfur remaining.

Rubber mixing process and its relationship with bound rubber and crosslink density

Science.gov (United States)

Hasan, A.; Rochmadi; Sulistyo, H.; Honggokusumo, S.

2017-06-01

This research studied the relationship between bound rubber and crosslink density based on rubber mixing process. Bound rubber was obtained after natural rubber was masticated and mixed with rubber chemicals and filler while crosslink density was collected after rubber compound was vulcanized. Four methods are used and each method refers to four ways of incorporating carbon black during mixing. The first method, after rubber was masticated for 5 minutes, the addition of rubber chemicals and filler was done simultaneously. Rubber was masticated for 1 minute and continued mixing of rubber chemicals and filler where mixing was different from first method. This was the second method. The third method was the same as the second method but the filler used N 660 while in the second method N 330. The last method is not the same as the first and second, the rubber is only masticated for 3 minutes and then mixed with filler and followed by rubber chemicals sequentially. The results showed that bound rubber and crosslink density were influenced by mixing and mastication process. Bound rubber dropped and crosslink density was relatively stable in the first three mixing methods for increasing carbon black at the beginning of the mixing process. Bound rubber and crosslink density stated opposite results in the fourth mixing method. The higher the bound rubber the lower the crosslink density. Without regard to mixing methods, there is a non-linear relationship between bound rubber formation and crosslink density determination

Investigations on the properties of NH4HCO3 filled natural rubber based magnetorheological elastomers (MREs)

Science.gov (United States)

Fan, Lili; Wang, Guoping; Wang, Wenju; Shi, Guanxin; Yang, Fufeng; Rui, Xiaoting

2018-04-01

Various anisotropic magnetorheological elastomers (MREs) were synthesized using the rubber mixing technique. Magnetic and temperature distributions of the experimental equipment and test instruments were analyzed by the ANSYS. NH4HCO3 was filled in the natural rubber matrix to modify properties of MREs. Microstructures and compositions of samples were studied by the scanning electron microscope (SEM), the energy dispersive x-ray spectroscopy (EDAX) analysis and x-ray powder diffraction (XRD). Via vibrating sample magnetometer (VSM) and density functional theory (DFT) method, the magnetic property of carbonyl iron (CI) was illuminated. The shear storage modulus and MR effect of MREs were investigated by the dynamic mechanical analyzer (DMA). It indicated that distributions of magnetic and temperature in the experimental and testing devices were uniform. Before vulcanization, CI particles were uniformly distributed in the matrix, while a CI chain structure was formed and embedded in the matrix after the vulcanization process. Moderate addition of NH4HCO3 accelerated the rubber vulcanization and enhanced the MR effect.

Nanocomposites of nitrile (NBR) rubber with multi-walled carbon nanotubes

Science.gov (United States)

Warasitthinon, Nuthathai

Nanotechnology offers the promise of creating new materials with enhanced performance. There are different kinds of fillers used in rubber nanocomposites, such as carbon black, silica, carbon fibers, and organoclays. Carbon nanotube reinforced elastomers have potential for improved rubber properties in aggressive environments. The first chapter is an introduction to the literature. The second chapter investigated the incorporation of multi-walled carbon nanotubes (MWCNTs) into rubber matrix for potential use in high temperature applications. The vulcanization kinetics of acrylonitrile butadiene rubber (NBR) reinforced with multi-walled carbon nanotubes was investigated. The vulcanized NBR rubber with different loading percentages of MWCNTs was also compared to NBR reinforced with carbon black N330. The optimum curing time at 170°C (T90) was found to decrease with increasing content of MWCNTs. Increased filler loading of both carbon black and MWCNTs gave higher modulus and strength. The MWCNTs filled materials gave better retention of modulus and tensile strength at high temperatures, but lower strength as compared to the carbon black filled samples. In the third chapter, carbon black (CB, 50phr) content in nitrile rubber (NBR) nanocomposites was partially replaced by multi-walled carbon nanotubes (MWCNTs). NBR/CB/CNTs nanocomposites with varying ratio of CB/CNTs (50/0 phr to 40/10 phr) were formulated via the melt-mixing method using an internal mixer. The reinforcing effect of single filler (CB) and mixture of fillers (CB and CNTs) on the properties of NBR nanocomposites was investigated. The cure kinetics and bound rubber content were analyzed using rheometry and solvent swelling method. In addition, mechanical behavior at both room temperature and high temperature (350°F/ 121°C) were examined. The scorch time and curing time values showed that there was no significant effect on the curing behavior of NBR nanocomposites after the partial replacement of CB with

Processing cost of RVNRL (Radiation Vulcanised Natural Rubber Latex)

International Nuclear Information System (INIS)

Wan Manshol Wan Zin; Meor Yahya Razali; Norjanah Mohd

1996-01-01

The main components contributing to the cost of building a pilot plant for RVNRL are highlighted. The fixed cost and operating cost of a pilot plant were determined and the production capacity and the cost to prepare I kg of RVNRL were calculated. Two sets of calculations were presented. A set was based on a pilot plant installed with cobalt-60 source of 150 kCi and another set was based on a plant installed with cobalt-60 source of I MCi. The effect of different power utilisation efficiencies and the effect of different vulcanization doses on the production capacities are presented.In general, a small difference in the vulcanization dose and power utilisation efficiency result in a significant change in the production capacity and the cost for RVNRL preparation. Depending on the production capacity, the cost for preparing RVNRL of 50% total solid content can be as low as RM 0.242 per kilograms

Incidence of latex harvesting technologies on agronomic and ...

African Journals Online (AJOL)

parameters and profitability of some rapid metabolic class clones of rubber ... of hormonal stimulation had no negative influence on the vegetative growth ..... yield (2597) was obtained with the control ..... metabolic energy of latex vessels as.

Latex Allergy - A Case Report

Directory of Open Access Journals (Sweden)

Dr. Athma Prasanna

2005-10-01

Full Text Available The usage of rubber and its products are not uncommon in various walks of life. A continuous exposure or contact may sensitize the human body, causing reactions from mild to fatal. Despite the availability of the literature, medical personnel are still unaware of the implications of the use of latex materials.

Preparation and properties of carboxylated styrene-butadiene rubber/cellulose nanocrystals composites.

Science.gov (United States)

Cao, Xiaodong; Xu, Chuanhui; Liu, Yuhong; Chen, Yukun

2013-01-30

A series of carboxylated styrene-butadiene rubber (XSBR)/cellulose nanocrystals (CNs) latex composites were successfully prepared. The vulcanization process, morphology, dynamic viscoelastic behavior, dynamic mechanical property, thermal and mechanical performance of the XSBR/CNs composites were investigated in detail. The results revealed that CNs were dispersed uniformly in the XSBR matrix and formed a strong filler-filler network. The dynamic mechanical analysis (DMA) showed that the glass transition temperature (T(g)) of XSBR matrix was shifted from 48.45 to 50.64 °C with 3 phr CNs, but decreased from 50.64 to 46.28 °C when further increasing CNs content up to 15 phr. The composites exhibited a significant enhancement in tensile strength (from 16.9 to 24.1 MPa) and tear strength (from 43.5 to 65.2 MPa) with loading CNs from 0 to 15 phr. In addition, the thermo-gravimetric analysis (TGA) showed that the temperature at 5% weight loss of the XSBR/CNs composites decreased slightly with an increase of the CNs content. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

The evaluation of tetrabutylamonium bis(4-ethylphenylsulphonyldithiocarbimate)zincate(II) (ZNIBU) efficiency as a reclaiming agent for styrene-butadiene rubber (SBR); Avalicao da eficiencia do bis(4-metilfenilsulfonilditiocarbimato)zincato(II) de tetrabutilamonio (ZNIBU) como agente de regeneracao para borracha de butadieno-estireno (SBR)

Energy Technology Data Exchange (ETDEWEB)

Moreno, Pedro H.H.; Visconte, Leila L.Y.; Pacheco, Elen B.A.V., E-mail: pedro_hhm@ima.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil); Tavares, Eder C. [Universidade Federal de Itajuba (UNIFEI), Itajuba, MG (Brazil)

2015-07-01

In recent years, the production of rubber waste has been reported as a serious environmental problem. The chemical structure of rubbers (crosslinked, insoluble and infusible polymers) makes its reprocessing very difficult, unlike thermoplastics. The most common methods to treat rubber waste are of thermal, mechanical and chemical nature, wherein the chemical methods the purpose is to regenerate the rubber. Early studies with tetrabutylamonium bis(4-methylphenylsulphonyldithiocarbimate)zincate(II) (ZNIBU) point to its ability as an accelerator in the rubber curing process. In this work, this zinc complex was evaluated as a chemical regeneration agent. ZNIBU was synthesized and characterized by Nuclear Magnetic Resonance ({sup 13}C NMR) and Fourier Transform Infrared Spectroscopy (FTIR). The mixture of virgin SBR with vulcanization ingredients was performed in a two-roll mill, and the composition was then vulcanized and molded on a hydraulic press. The synthesized ZNIBU was then mixed with the vulcanized rubber and devulcanization was observed. Finally, the devulcanized elastomeric composition was revulcanized. The revulcanization of SBR regenerated with ZNIBU led to the formation of a rubber with maximum torque near the maximum torque of the virgin vulcanized rubber. After adjusting the optimal conditions of regeneration, mechanical tests will be carried out (tensile strength, tear strength and hardness) for the specimens of both vulcanized and revulcanized rubbers in order to compare their mechanical properties. (author)

Styrene-butadiene rubber/halloysite nanotubes nanocomposites modified by sorbic acid

Energy Technology Data Exchange (ETDEWEB)

Guo Baochun, E-mail: psbcguo@scut.edu.cn [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China); Chen Feng; Lei Yanda; Liu Xiaoliang; Wan Jingjing; Jia Demin [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China)

2009-05-30

Sorbic acid (SA) was used to improve the performance of styrene-butadiene rubber (SBR)/halloysite nanotubes (HNTs) nanocomposites by direct blending. The detailed mechanisms for the largely improved performance were studied by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), porosity analysis and crosslink density determination. The strong interfacial bonding between HNTs and rubber matrix is resulted through SA intermediated linkages. SA bonds SBR and HNTs through grafting copolymerization/hydrogen bonding mechanism. Significantly improved dispersion of HNTs in virtue of the interactions between HNTs and SA was achieved. Formation of zinc disorbate (ZDS) was revealed during the vulcanization of the composites. However, in the present systems, the contribution of ZDS to the reinforcement was limited. Effects of SA content on the vulcanization behavior, morphology and mechanical properties of the nanocomposites were investigated. Promising mechanical properties of SA modified SBR/HNTs nanocomposites were obtained. The changes in vulcanization behavior, mechanical properties and morphology were correlated with the interactions between HNTs and SA and the largely improved dispersion of HNTs.

Development assessment of natural latex membranes: a new proposal for the treatment of amblyopia

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, Jaqueline Alves; Rosa, Suelia Rodrigues Fleury, E-mail: jackalvesribeiro@gmail.com [Laboratorio de Engenharia e Biomaterial (BioEngLab), Faculdade Gama, Universidade de Brasilia (UnB), DF (Brazil); Leite, Cicilia Raquel Maia; Vasconcelos, Claudio Lopes; Soares, Joao Maria [Universidade do Estado do Rio Grande do Norte (UERN), Mossoro, RN (Brazil)

2017-05-15

The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes. (author)

Development assessment of natural latex membranes: a new proposal for the treatment of amblyopia

International Nuclear Information System (INIS)

Ribeiro, Jaqueline Alves; Rosa, Suelia Rodrigues Fleury; Leite, Cicilia Raquel Maia; Vasconcelos, Claudio Lopes; Soares, Joao Maria

2017-01-01

The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes. (author)

High-resolution photoelectron spectroscopy analysis of sulfidation of brass at the rubber/brass interface

Energy Technology Data Exchange (ETDEWEB)

Ozawa, Kenichi, E-mail: ozawa.k.ab@m.titech.ac.jp [Department of Chemistry and Materials Science, Tokyo Institute of Technology, Ookayama, Meguro-ku, Tokyo 152-8551 (Japan); Kakubo, Takashi; Shimizu, Katsunori; Amino, Naoya [Yokohama Rubber Co., Ltd., Oiwake, Hiratsuka 254-8601 (Japan); Mase, Kazuhiko [Institute of Materials Structure Science, High Energy Accelerator Research Organization (KEK), Tsukuba 305-0801 (Japan); Komatsu, Takayuki [Department of Chemistry and Materials Science, Tokyo Institute of Technology, Ookayama, Meguro-ku, Tokyo 152-8551 (Japan)

2013-01-01

Highlights: Black-Right-Pointing-Pointer Chemical composition at the rubber/brass interface is investigated. Black-Right-Pointing-Pointer The 2-min vulcanization reaction is enough to convert the interface composition. Black-Right-Pointing-Pointer Five S-containing species are identified at the interface. Black-Right-Pointing-Pointer Strong rubber-brass adhesion is related to the Cu{sub 2}S/CuS ratio. Black-Right-Pointing-Pointer Degradation of adhesion proceeds along with desulfidation of the interface. - Abstract: High resolution photoelectron spectroscopy is utilized to investigate the chemical composition at the rubber/brass interface to elucidate the origin of strong adhesion as well as the degradation between rubber and brass. Special attention has been given to copper sulfides formed at the interface during the vulcanization reaction at 170 Degree-Sign C. At least five sulfur-containing species are identified in the adhesive interlayer including crystalline CuS and amorphous Cu{sub x}S (x Asymptotically-Equal-To 2). These copper sulfide species are not uniformly distributed within the layer, but there exits the concentration gradation; the concentration of Cu{sub x}S is high in the region on the rubber side and is diminished in the deeper region, while vice versa for that of CuS. Degradation of the interface adhesive strength by prolonged vulcanization arises from the decrease in the Cu{sub x}S/CuS ratio accompanying desulfurization of the adhesive layer.

Effect of magnetic and thermal properties of iron oxide nanoparticles (IONs) in nitrile butadiene rubber (NBR) latex

International Nuclear Information System (INIS)

Ong, Hun Tiar; Julkapli, Nurhidayatullaili Muhd; Hamid, Sharifah Bee Abd; Boondamnoen, O.; Tai, Mun Foong

2015-01-01

Nitrile butadiene rubber (NBR) gloves are one of the most important personal protective equipments but they are possible to tear off and contaminate food or pharmaceutical and healthcare products during manufacturing and packaging process. High tendency of torn glove remaining in food or products due to white or light flesh-coloured glove is not easy to be detected by naked eyes. In this paper, iron oxide nanoparticles (IONs) selected as additive for NBR to improve its detectability by mean of magnetic properties. IONs synthesized via precipitation method and compounded with NBR latex before casting on petri dish. The properties of IONs were investigated by X-ray Diffractometry (XRD), Transmission Electron Microscope (TEM), Raman Spectroscopy and Vibrating Sample Magnetometer (VSM). Meanwhile NBR/IONs composites were studied by Thermogravimetry Analysis (TGA), Differential Scanning Calorimetry (DSC) and Vibrating Sample Magnetometer (VSM). It observed that, synthesized IONs shows of 25.28 nm crystallite with 25.86 nm semipherical (changed as) shape. Meanwhile, Magnetite and maghemite phase are found in range of 670 cm −1 and 700 cm −1 respectively, which it contributes magnetization saturation of 73.96 emu/g at 10,000 G by VSM. Thermal stability and magnetic properties were increased with incorporating IONs into NBR latex up to 20 phr. NBR/IONs 5 phr has the optimum thermal stability, lowest glass transition temperature (−14.83 °C) and acceptable range of magnetization saturation (3.83 emu/g at 10,000 G) to form NBR gloves with magnetic detectability. - Highlights: • We synthesized IONs with high magnetization saturation (M s ). • High M s of IONs were incorporated into NBR latex in order to induce magnetic properties in the NBR composite. • Introduction of IONs into NBR latex would improve thermal properties. • The produced NBR/IONs 5 phr composite exceeded the minimum magnetic moment sensor of the detector. • They have high potential for the

Effect of magnetic and thermal properties of iron oxide nanoparticles (IONs) in nitrile butadiene rubber (NBR) latex

Energy Technology Data Exchange (ETDEWEB)

Ong, Hun Tiar; Julkapli, Nurhidayatullaili Muhd; Hamid, Sharifah Bee Abd, E-mail: sharifahbee@um.edu.my; Boondamnoen, O.; Tai, Mun Foong

2015-12-01

Nitrile butadiene rubber (NBR) gloves are one of the most important personal protective equipments but they are possible to tear off and contaminate food or pharmaceutical and healthcare products during manufacturing and packaging process. High tendency of torn glove remaining in food or products due to white or light flesh-coloured glove is not easy to be detected by naked eyes. In this paper, iron oxide nanoparticles (IONs) selected as additive for NBR to improve its detectability by mean of magnetic properties. IONs synthesized via precipitation method and compounded with NBR latex before casting on petri dish. The properties of IONs were investigated by X-ray Diffractometry (XRD), Transmission Electron Microscope (TEM), Raman Spectroscopy and Vibrating Sample Magnetometer (VSM). Meanwhile NBR/IONs composites were studied by Thermogravimetry Analysis (TGA), Differential Scanning Calorimetry (DSC) and Vibrating Sample Magnetometer (VSM). It observed that, synthesized IONs shows of 25.28 nm crystallite with 25.86 nm semipherical (changed as) shape. Meanwhile, Magnetite and maghemite phase are found in range of 670 cm{sup −1} and 700 cm{sup −1} respectively, which it contributes magnetization saturation of 73.96 emu/g at 10,000 G by VSM. Thermal stability and magnetic properties were increased with incorporating IONs into NBR latex up to 20 phr. NBR/IONs 5 phr has the optimum thermal stability, lowest glass transition temperature (−14.83 °C) and acceptable range of magnetization saturation (3.83 emu/g at 10,000 G) to form NBR gloves with magnetic detectability. - Highlights: • We synthesized IONs with high magnetization saturation (M{sub s}). • High M{sub s} of IONs were incorporated into NBR latex in order to induce magnetic properties in the NBR composite. • Introduction of IONs into NBR latex would improve thermal properties. • The produced NBR/IONs 5 phr composite exceeded the minimum magnetic moment sensor of the detector. • They have high

Latex Allergy In Health Care Workers

Directory of Open Access Journals (Sweden)

Hayriye Sarıcaoğlu

2013-05-01

Full Text Available Background and Design: We aimed to determine the frequency of latex allergy in our hospital and to to evaluate the clinical and demographical features of the cases.Materials and Methods: A detailed questionnaire was administered to healthcare workers by a physician. Skin prick test with latex and patch test with rubber chemicals and a piece of latex glove were performed for all healthcare workers. Latex-specific IgE was measured in serum.Results: The study sample consisted of 36 nurses, 14 doctors, and 50 healthcare workers. While 46 subjects had symptoms, 54 subjects had no symptoms. The relationship of clinical disease with working duration, exposure duration (hour/day, history of atopy, and drug/food allergies was statistically significant. Five nurses and 1 healthcare worker had positive skin prick test. Two of them had positive latex-specific IgE. Positive skin prick test statistically significantly correlated with occupation, working duration, exposure duration (hour/day and positive latex-specific IgE. Two nurses and 2 healthcare workers had positive latex-specific IgE. Two of them had positive skin prick test. Positive latexspecific IgE statistically significantly correlated with working duration, exposure duration, and positive skin prick test. Patch test with a piece of latex glove was negative in all subjects. Three healthcare workers had positive patch test with thiuram-mix, one of them had also positive patch test with mercaptobenzothiazole.Discussion: One of the risk factors for latex allergy is occupations involving frequent exposure to latex products. Latex allergy should be taken into consideration if type I hypersensitivity reactions occur in occupational groups at risk for anaphylactic reaction.

Natural rubber/high density polyethylene/ground rubber composites vulcanized by gamma irradiation

International Nuclear Information System (INIS)

Shaltout, N.A.; Abou zeid, M.M.; Khalil, A.M.; El Miligy, A.A.

2010-01-01

Natural rubber (NR) was blended mechanically with 50 phr high density polyethylene (HDPE). the mechanical, physical and thermal properties of NR/HDPE blend and its composites with different contents of ground tire rubber (GTR) before and after exposure to gamma irradiation to various doses up to 250 kGy were studied. Also, the change in structure morphology of irradiated NR/HDPE blend as well as NR/HDPE/GTR composites was examined by scanning electron microscope (SEM). The results showed that the substitution of a part of virgin NR with GTR decreases the mechanical and physical properties but not to the extent of deterioration . However, it was found that the mechanical and physical properties were improved after gamma irradiation . Composite of NR/GTR/HDPE (75/25/50) showed good properties. Scanning electron microscope showed homogeneity between the irradiated composites ingredients.

Tensile properties of carbon black-filled natural rubber latex films using two different approaches of film preparation

Science.gov (United States)

Jarkasi, Siti Aisyah; Samsuri, Azemi; Hashim, M. Y. Amir; Kamarun, Dzaraini

2017-09-01

A study was structured to investigate the effects of two different approaches of black-filled NRL films preparation on tensile strengths and tensile stress at 100% strain (M100). In the "First Approach", carbon black dispersion was added into the NRL and mixed using mechanical stirrer. Then the black-filled NRL was coagulated with acetic acid and dried to form NR black-filled masterbatch. This black-filled NR masterbatch was then masticated and mixed with other compounding ingredients on the 2-roll mill. In the "Second Approach", carbon black dispersion was mixed with NRL plus all other compounding ingredients using a mechanical stirrer at high mechanical stirring speed (200 rpm) for 3 hrs. Tensile test-pieces from these two rubber specimens were tested according to ISO37. It was observed that the tensile strengths are affected by both methods. In the case of masticated latex masterbatch, the black-filled NRL films gave higher tensile strength (25-27 MPa) as compared to un-masticated black-filled NRL films (11-17 MPa). The optimum amount of filler loading for highest tensile strength in both approaches was 20 phr of carbon black. However these different approaches did not give significant effect to the elongation at break, EB and M100. SEM images of samples prepared from both approaches suggested that the dispersion of filler in the rubber matrix was better in the masticated samples compared to the un-masticated samples. The reason for the difference in the tensile strength between the two black-filled rubbers might be associated with the degree of dispersions and the uniformity of the dispersions within the rubber matrix. The first mixing approach involved high mechanical shearing action during mastication and mixing process on the 2-roll mill. The high shearing actions were able to breakdown filler aggregates efficiently and distributed the dispersed filler uniformly within the rubber matrix. In the second approach, the breakdown of filler aggregates relied on

The effect of emulsifier on the stability of irradiated LA-TZ latex

International Nuclear Information System (INIS)

Made Sumarti K; Utama, Marga; Puspitasari, Tita

1998-01-01

The effect of six kinds of stabilizer on the stability of the concentrated LA-TZ latex which contains n-BA have been studied. The six stabilizers are: 1. Naphthalene sulfonic acid formaldehyde condensate, 2. Sodium dialkyl sulfosuccinate, 3. Triethanol amine lauryl sulfate, 4. Sodium polyoxyethylene alkyl phenol ether sulfate, 5. Dodecyl benzene sulfonic acid (Neopelex FS), and 6. Ammonium laurat. The concentrations of the stabilizers are in the range of 0,1 to 0,3% and of the n-BA is 5phr (per hundred rubber). The field natural rubber latex was stabilized by Tetramethyl tiuram disulfide - Zine oxide (TMTD-ZnO) and ammonium gas, and was concentrated by centrifuge. The obtain concentrated LA-TZ latex was added by the n-BA and was kept with various storage time i.e. o, 2, 4, 6, 18, and 24 hours. It was found that the stable latex was irradiated by 15 kGy dose and the physical properties was tested, then the maximum tensile strength of 223,3 kg/cm 2 was found on Neopelex FS concentrate at 0,1%. (authors)

Pemanfaatan Silika Abu Sekam Padi sebagai Bahan Pengisi Rubber Membrane Filter Press untuk Memisahkan Minyak Inti Sawit

OpenAIRE

Nasruddin

2012-01-01

This research was aimed to obtain rubber membrane filter press (RMFP) from natural rubber (NR) as well as synthetic rubber (chloroprene rubber and nytrike butadiene rubber). The research method was done my vulcanizing natural rubber, synthetic rubber, and filler to shape RMFP. Research formulation was done with 8 units of experiments using variations of mixers that have been pre-determined. The examination to the RMFP was done with ASTM test methods that cover parameters such as viscometer mo...

Technological properties of latex and natural rubber of Hevea brasiliensis clones Propriedades tecnológicas do látex e da borracha natural de clones de Hevea brasiliensis

Directory of Open Access Journals (Sweden)

Rogério Manoel Biagi Moreno

2005-04-01

Full Text Available Rubber industry has increased the requirements for quality and uniformity of natural rubber produced in Brazil. Technological properties of latex and natural rubber of clones GT 1, PB 235, IAN 873 and RRIM 600 [Hevea brasiliensis (Willd. Former Adr. de Juss. Muell.- Arg] were evaluated by standard methods of the dry rubber content (DRC%, percentage of nitrogen (N% and percentage of ashes (ASH% in two consecutive years; data were correlated with temperature and precipitation. Properties of latex and natural rubber varied (P A indústria da borracha está cada vez mais exigente em relação à qualidade e a uniformidade da borracha natural produzida no Brasil. Neste trabalho as propriedades tecnológicas do látex e da borracha natural dos clones de seringueira GT 1, PB 235, IAN 873 e RRIM 600 [Hevea brasiliensis (Willd. ex Adr. de Juss. Muell.-.Arg] foram avaliadas pelos ensaios padrões do conteúdo de borracha seca (DRC%, porcentagem de nitrogênio (N% e porcentagem de cinzas (CNZ% por dois anos consecutivos; os dados obtidos foram correlacionados com dados de temperatura e precipitação. As propriedades do látex e da borracha natural variaram (P < 0.01 em função do tipo de clone e entre coletas. O DRC% diminuiu no início da estação seca (maio a junho, enquanto N% e CNZ% aumentaram. O período de abril a junho revelou ser crítico, pois os valores da N% oscilaram acima 0,60%, fora dos padrões estabelecidos pela norma técnica brasileira ABNT/NBR. O clone RRIM 600 foi menos suscetível às variações climáticas.

Nanosílice como carga en la RTV SR usada para cubrir aisladores; Nanosilica as filler in the Room temperature vulcanized silicone rubber used to coat insulators

Directory of Open Access Journals (Sweden)

Ignat Pérez Almirall

2014-04-01

Full Text Available En el presente trabajo se realiza un estudio sobre la influencia que tiene agregar como carga nanosílice a la goma de silicona vulcanizada a temperatura ambiente (RTV SR, por sus siglas en inglés que es empleada para cubrir aisladores de vidrio o de porcelana. Con este objetivo se observó la dispersión de la nanosílice en la RTV SR por medio de microscopía electrónica de barrido (MEV, por sus siglas en inglés, se midió la permitividad de la RTV SR con y sin nanosílice para varias frecuencias y se evaluó la influencia que tiene la nanosílice en la resistencia a la erosión. Además fueron medidas las corrientes de fuga durante ensayos de niebla salina a aisladores de vidrio pintados con estos recubrimientos, analizando también la pérdida de hidrofobicidad que ocurre durante el ensayo y su recuperación una vez finalizado el mismo.  The present research work carries out a study on the influence of nanosilica on room temperature vulcanized silicone rubber (RTV SR used to coat insulators. Considering this objective, the dispersion of nanosilica was observed by means of scanning electron microscopy (MEV, the permittivity of the room temperature vulcanized silicone rubber was measured with and without nanosilica for different frequencies and the influence of nanosilica in erosion resistance. Leakage currents were also measured during salt spray tests to glass insulators covered with these coatings; the loss of hidrophobicity during the test was also measured and its recovery was analyzed the test was finished.

Nanosílice como carga en la RTV SR usada para cubrir aisladores/ Nanosilica as filler in the Room temperature vulcanized silicone rubber used to coat insulators

Directory of Open Access Journals (Sweden)

Ignat Pérez Almirall

2012-02-01

Full Text Available En el presente trabajo se realiza un estudio sobre la influencia que tiene agregar como carga nanosílice a la goma de silicona vulcanizada a temperatura ambiente (RTV SR, por sus siglas en inglés que es empleada para cubrir aisladores de vidrio o de porcelana. Con este objetivo se observó la dispersión de la nanosílice en la RTV SR por medio de microscopía electrónica de barrido (MEV, por sus siglas en inglés, se midió la permitividad de la RTV SR con y sin nanosílice para varias frecuencias y se evaluó la influencia que tiene la nanosílice en la resistencia a la erosión. Además fueron medidas las corrientes de fuga durante ensayos de niebla salina a aisladores de vidrio pintados con estos recubrimientos, analizando también la pérdida de hidrofobicidad que ocurre durante el ensayo y su recuperación una vez finalizado el mismo.The present research work carries out a study on the influence of nanosilica on room temperature vulcanized silicone rubber (RTV SR used to coat insulators. Considering this objective, the dispersion of nanosilica was observed by means of scanning electron microscopy (MEV, the permittivity of the room temperature vulcanized silicone rubber was measured with and without nanosilica for different frequencies and the influence of nanosilica in erosion resistance. Leakage currents were also measured during salt spray tests to glass insulators covered with these coatings; the loss of hidrophobicity during the test was also measured and its recovery was analyzed the test was finished.

Styrene grafted natural rubber reinforced by in situ silica generated via sol–gel technique

Energy Technology Data Exchange (ETDEWEB)

Sittiphan, Torpong [Program of Petrochemistry and Polymer Sciences, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand); Prasassarakich, Pattarapan [Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand); Poompradub, Sirilux, E-mail: sirilux.p@chula.ac.th [Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand)

2014-02-15

Highlights: • Sol–gel reaction by NR latex was the absence of use of organic solvent and base catalyst. • Well dispersed in situ formed silica particles in the rubber matrix were obtained. • In situ silica was better to improve mechanical properties of rubber vulcanizates. -- Abstract: The filling of styrene graft natural rubber (ST-GNR) with in situ formed silica was performed using the sol–gel reaction via the latex solution method. The mechanical properties of ST-GNR/NR vulcanizate were improved when using the in situ formed silica to levels higher than those obtained with the commercial ex situ formed silica filled ST-GNR/NR vulcanizates at a comparable silica content of 12 parts by weight per hundred parts of rubber. Transmission electron microscopy analysis revealed that the in situ silica particles were small (∼40 nm diameter) and well dispersed, while the commercial silica particles were larger (∼60 nm diameter) and markedly agglomerated in the rubbery matrix. The mechanical properties of the composites prepared via both the solid rubber and latex solution methods were comparable.

Rubber gloves biodegradation by a consortium, mixed culture and pure culture isolated from soil samples.

Science.gov (United States)

Nawong, Chairat; Umsakul, Kamontam; Sermwittayawong, Natthawan

2018-02-03

An increasing production of natural rubber (NR) products has led to major challenges in waste management. In this study, the degradation of rubber latex gloves in a mineral salt medium (MSM) using a bacterial consortium, a mixed culture of the selected bacteria and a pure culture were studied. The highest 18% weight loss of the rubber gloves were detected after incubated with the mixed culture. The increased viable cell counts over incubation time indicated that cells used rubber gloves as sole carbon source leading to the degradation of the polymer. The growth behavior of NR-degrading bacteria on the latex gloves surface was investigated using the scanning electron microscope (SEM). The occurrence of the aldehyde groups in the degradation products was observed by Fourier Transform Infrared Spectroscopy analysis. Rhodococcus pyridinivorans strain F5 gave the highest weight loss of rubber gloves among the isolated strain and posses latex clearing protein encoded by lcp gene. The mixed culture of the selected strains showed the potential in degrading rubber within 30 days and is considered to be used efficiently for rubber product degradation. This is the first report to demonstrate a strong ability to degrade rubber by Rhodococcus pyridinivorans. Copyright © 2018. Published by Elsevier Editora Ltda.

Ultraviolet curing of acrylated liquid natural rubber for surface coating application

OpenAIRE

Kannikar Kwanming; Pairote Klinpituksa; Wae-asae Waehamad

2009-01-01

Ultraviolet curable acrylated liquid natural rubber was prepared by grafting of photosensitive molecule onto liquid natural rubber for surface coating application. The liquid natural rubber (LNR) was firstly obtained by degradation of natural rubber latex with hydrogen peroxide and cobalt acetylacetonate at 65oC for 72 hrs. The preparation of acrylated natural rubber was carried out by the reaction of acrylic acid and epoxidized liquid natural rubber (ELNR) prior obtained from LNR with formic...

High-resolution photoelectron spectroscopy analysis of sulfidation of brass at the rubber/brass interface

International Nuclear Information System (INIS)

Ozawa, Kenichi; Kakubo, Takashi; Shimizu, Katsunori; Amino, Naoya; Mase, Kazuhiko; Komatsu, Takayuki

2013-01-01

Highlights: ► Chemical composition at the rubber/brass interface is investigated. ► The 2-min vulcanization reaction is enough to convert the interface composition. ► Five S-containing species are identified at the interface. ► Strong rubber–brass adhesion is related to the Cu 2 S/CuS ratio. ► Degradation of adhesion proceeds along with desulfidation of the interface. - Abstract: High resolution photoelectron spectroscopy is utilized to investigate the chemical composition at the rubber/brass interface to elucidate the origin of strong adhesion as well as the degradation between rubber and brass. Special attention has been given to copper sulfides formed at the interface during the vulcanization reaction at 170 °C. At least five sulfur-containing species are identified in the adhesive interlayer including crystalline CuS and amorphous Cu x S (x ≃ 2). These copper sulfide species are not uniformly distributed within the layer, but there exits the concentration gradation; the concentration of Cu x S is high in the region on the rubber side and is diminished in the deeper region, while vice versa for that of CuS. Degradation of the interface adhesive strength by prolonged vulcanization arises from the decrease in the Cu x S/CuS ratio accompanying desulfurization of the adhesive layer.

Oxygen Plasma Treatment of Rubber Surface by the Atmospheric Pressure Cold Plasma Torch

DEFF Research Database (Denmark)

Lee, Bong-ju; Kusano, Yukihiro; Kato, Nobuko

1997-01-01

adhesive. The adhesion property was improved by treatment of the rubber compound with plasma containing oxygen radicals. Physical and chemical changes of the rubber surface as a result of the plasma treatment were analyzed by field emission scanning electron microscopy (FE-SEM) and fourier transform......A new application of the atmospheric cold plasma torch has been investigated. Namely, the surface treatment of an air-exposed vulcanized rubber compound. The effect of plasma treatment was evaluated by the bondability of the treated rubber compound with another rubber compound using a polyurethane...

Effect of Graphite on the Properties of Natural Rubber

Directory of Open Access Journals (Sweden)

Auda jabber Braihi

2016-09-01

Full Text Available Natural rubber-graphite composites (0, 1, 2, 3, 4 pphr graphite were prepared on a laboratory two-roll mill. Swelling measurements were used to evaluate the impacts of graphite on the properties of natural rubber. Swelling results showed that the volume fraction of natural rubber in the swollen gel, the interaction parameter, and the cross-link density decreased by increasing graphite loadings, while the average molecular weight of natural rubber between cross-links increased. Vulcanization results showed that only scorch time parameter increased with increasing graphite loadings, while other parameters (Max. torque, Min. torque, cure rate and cure rate index decreased. Both thermal and AC conductivities increased.

Effect of gamma irradiation on sulfur-cured chlorobutyl rubber

International Nuclear Information System (INIS)

Scagliusi, Sandra R.; Cardoso, Elisabeth E.L.; Ono, Lilian S.; Lugao, Ademar B.

2011-01-01

Chlorobutyl rubber (CIIR) is similarly manufactured to butyl rubber (IIR). The insertion of chlorine atom in isoprene group represents an improvement in its properties, such as: high vulcanizing speed, low permanent stress and compatibility with other types of rubber. The presence of reactive chlorine in butyl chlorate allows a variety of vulcanizing techniques, being the cure via sulfur, the most conventional. In these compounds carbon-halogen bonds are weaker than carbon-carbon and carbon-hydrogen bonds, and the main effect of radiation is to break the carbon-halogen bond to give an organic free radical. Irradiations of certain alkyl chlorides can bring about isomerism in which the location of the halogen atom is changed, the carbon skeleton of molecule remaining unaltered. Irradiation of n-butyl chlorides gives high yields of tertiary carbon. The major effect of high energy photon, such as gamma rays, in organic polymers is the generation of free radicals, along changes in mechanical properties. This work aims to the study of irradiation effect on mechanical properties of a sulfur cured chlorobutyl rubber compound, gamma irradiated within 25, 50, 100, 150 e 200 kGy doses range. The techniques used in their characterization were: strength - stress analysis and elasticity modulus. Results obtained were investigated, demonstrated and discussed. (author)

Effect of gamma irradiation on sulfur-cured chlorobutyl rubber

Energy Technology Data Exchange (ETDEWEB)

Scagliusi, Sandra R.; Cardoso, Elisabeth E.L.; Ono, Lilian S.; Lugao, Ademar B., E-mail: srscagliusi@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

Chlorobutyl rubber (CIIR) is similarly manufactured to butyl rubber (IIR). The insertion of chlorine atom in isoprene group represents an improvement in its properties, such as: high vulcanizing speed, low permanent stress and compatibility with other types of rubber. The presence of reactive chlorine in butyl chlorate allows a variety of vulcanizing techniques, being the cure via sulfur, the most conventional. In these compounds carbon-halogen bonds are weaker than carbon-carbon and carbon-hydrogen bonds, and the main effect of radiation is to break the carbon-halogen bond to give an organic free radical. Irradiations of certain alkyl chlorides can bring about isomerism in which the location of the halogen atom is changed, the carbon skeleton of molecule remaining unaltered. Irradiation of n-butyl chlorides gives high yields of tertiary carbon. The major effect of high energy photon, such as gamma rays, in organic polymers is the generation of free radicals, along changes in mechanical properties. This work aims to the study of irradiation effect on mechanical properties of a sulfur cured chlorobutyl rubber compound, gamma irradiated within 25, 50, 100, 150 e 200 kGy doses range. The techniques used in their characterization were: strength - stress analysis and elasticity modulus. Results obtained were investigated, demonstrated and discussed. (author)

Review of food toxicological issues associated in rubber products

OpenAIRE

Ng, Mei Xiang; Ong, S.P.; Hii, C.L.; Chuah, L.A.; Law, C.L.

2014-01-01

Over the centuries, rubber latex gained its popularity in machinery application due to its unique thermal properties, high elasticity and excellent impact resistance. It is widely accepted in food industry as rubber has good resistance to chemicals, including acids, alkalis and salts. For instance, rubber components comprise of couplings, shields, dust covers, gaskets and seals exist as group or standalone component in food manufacturing equipments or machinery. Even though most of the rubber...

Alternative secondary accelerator for silica-filled natural rubber formulations

NARCIS (Netherlands)

Kaewsakul, Wisut; Sahakaro, Kannika; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

2013-01-01

Dithiophosphate (DTP) displays a good efficiency towards improved overall properties of silica-reinforced natural rubber compounds, when it is used as secondary accelerator in a sulfenamide primary accelerated sulfur vulcanization system. Comparing DTP with diphenylguanidine (DPG), DTP is more

Caracterização da hipersensibilidade a luvas de látex em profissionais da odontologia - DOI: 10.4025/actascihealthsci.v29i1.103 Rubber latex gloves hypersensitivities in dental workers - DOI: 10.4025/actascihealthsci.v29i1.103

Directory of Open Access Journals (Sweden)

Ana Maria Sell

2007-12-01

Full Text Available As reações alérgicas ao látex vêm aumentando em profissionais da saúde e se manifestam como um incômodo local ou sintomatologia sistêmica. Para conhecer a freqüência das manifestações alérgicas nos usuários de luvas de látex foi realizada busca entre os profissionais da odontologia via aplicação de questionários. Foram aplicados 450 questionários e, dentre os respondedores (140, 19% relataram manifestar reações locais ao contato com as luvas de látex e 5% reações sistêmicas a outros produtos de látex. Cerca de 2,5% declararam dermatite de contato e reações sistêmicas (anafiláticas, 1,5% apenas dermatite de contato e 1% sintomas de anafilaxia ao uso das luvas. Vinte por cento dos profissionais atenderam pacientes com alergia ao látex e 29% declararam questionar, durante a anamnese, a respeito de alergia ao látex. As reações alérgicas a luvas de látex foram freqüentes e é objeto de preocupação entre os profissionais da odontologia.Allergic reactions to natural rubber latex have increased in dental practice affecting both the professional and the patients. Allergic reactions may range from skin disease to asthma and anaphylaxis. This study aimed at determining the incidence of latex gloves allergy among dental care workers. 450 allergy questionnaires were used to collect information on latex gloves reactions and 140 dental works answered them. Latex gloves reaction occurred in 19% of them and 5% reported allergic reactions to other latex products. 2.5% reported symptoms suggesting contact dermatitis and anaphylaxis hypersensitivities, 1.5% contact dermatitis, and 1% reported anaphylaxis symptoms when wearing them. 20% of them had patients who presented symptoms suggestive of anaphylaxis hypersensitivity to rubber gloves latex. Our study confirms that rubber latex gloves reactions are frequent among dental care workers, and dentists must be aware of the latex allergy in dental practice.

Troubleshooting for the observed problems in processing latex concentrate from natural resource

International Nuclear Information System (INIS)

Afreen, S; Haque, K R; Huda, M K

2013-01-01

Natural latex has special importance in the rubber industry for manufacturing different types of goods like gloves, balloons, male contraceptive and similar thin walled articles. This natural latex is much more sensitive a liquid to handle since it can easily become contaminated and thereby coagulated which makes it unfavourable for centrifuge and getting concentrate from it. Some other related measures also are included in consideration during the processing of concentrate latex from the natural raw latex. The problems that are being faced in a concentrate latex processing plant can be categorized in different groups like, problems related to the latex property, mechanical problems, electrical problems, handling and storage problems, transformation problems, problems related to environmental issues, etc. Among them, the most common and vital problems frequently observed in a concentrate latex processing plant are discussed here with a view to finding the measures for solution which will help to maintain the latex property in any latex processing plant.

Pengaruh Penggunaan Nitril Butadiene Rubber Dan Pale Crepe Pada Pembuatan Sol Karet Untuk Sepatu Pengaman

OpenAIRE

Yuniari, Arum

2010-01-01

Rubber sole for safety shoes was different on physical specification with general sole, especially on abrasion resistance and oil resistance. The objective of the study was to determine the effect of nitril butadiene rubber and pale crepe on physical properties of vulcanized rubber sole for safety shoes. Rubber sole for safety shoes was produced by blending pale crepe and nitril butadiene rubber with ratio of : 50/50; 60/40; 70/30 and 80/20 phr, respectively. Carbon black as filler was also v...

Pengaruh penggunaan nitril butadiene rubber dan pale crepe pada pembuatan sol karet untuk sepatu pengaman

OpenAIRE

Arum Yuniari

2010-01-01

Abstract Rubber sole for safety shoes was different on physical specification with general sole, especially on abrasion resistance and oil resistance. The objective of the study was to determine the effect of nitril butadiene rubber and pale crepe on physical properties of vulcanized rubber sole for safety shoes. Rubber sole for safety shoes was produced by blending pale crepe and nitril butadiene rubber with ratio of : 50/50; 60/40; 70/30 and 80/20 phr, respectively. Carbon black as fill...

Rubber molds for investment casting

International Nuclear Information System (INIS)

Sibtain, S.N.

2011-01-01

The main objective of the project is to investigate different types of molding rubbers used for investment casting. The level of shape complexity which can be achieved by using these rubber molds is also studied. It was almost impossible to make complex shapes molds using metal molds, in that cases rubber molds are very important because they arc flexible and give accurate and precise part dimensions. Turbine blades are hi-tech components with air-foil geometries that have close dimensional tolerances. They are made of super-alloys and manufactured by investment casting. The final blade profile depends upon the dimensional accuracy in each of the processing steps. In the present work experimental study for the production of high quality low cost castings of turbine blades using rubber molds and injected wax patterns is presented. Natural Rubber molds and wax patterns from these molds were made. Different types of molding rubbers were studied including natural rubber, silicone rubber and liquid silicone rubber. It was found that by using rubber molds we can make most complex shape with very less finishing required. The shrinkage was 12% as compared to original master pattern. Rubber molds were made using laboratory hot press. Three layers of rubber above and below the master pattern. After that vulcanization was done by giving temperature and pressure. (author)

Synthesis and characterization of silver nanoparticles in natural rubber

International Nuclear Information System (INIS)

Abu Bakar, N.H.H.; Ismail, J.; Abu Bakar, M.

2007-01-01

Silver nanoparticles are formed in natural rubber matrix via photo reduction of film cast from natural rubber latex (NRL) containing silver salt. The resulting NR-Ag nanocomposite is characterized using TEM, XRD and UV spectroscopic techniques. The nanoparticles, diameter ranging between 4 and 10 nm, are dispersed within distinct interfaces which correspond to the inter-particle boundaries of the NRL particles that form the matrix. The average width of the interfaces is 8 nm. X-ray diffraction (XRD) analysis confirms the nanoparticles as metallic silver of the face-centered cubic type. UV-vis absorption spectra show peaks characteristic of the surface plasmon resonance of nano-sized silver. A comparison with the results of formation of silver, obtained under similar reduction condition, in a series of matrices namely de-proteinized natural rubber latex (DNRL), NRL containing sodium dodecyl sulfate (SDS), aqueous solutions of bovain serum albumin and SDS, suggests that the protein in natural rubber is responsible for the formation of stable silver nanoparticles in the natural rubber (NR) matrix

Studies on physico-chemical and mechanical properties of the irradiated latex modified mortar

International Nuclear Information System (INIS)

Yassene, A.A.M.A.

2009-01-01

This thesis contains three chapter; chapter(I): Introduction and literature review on:- Introduction to polymer. - Mechanism of polymer-cement co-matrix formation.-Sulphate attack. - Solidification /stabilization of heavy metal in cement mortar. chapter(II): Materials and experimental techniques that include: 1- Preparation of latex polymer films from different polymer latices of styrene butadine rubber latex (SBR), poly (styrene-acrylic ester) latex (SAE) and vinylacetate /versatic -ester copolymer latex (C2A). The effect of γ-irradiation dose on the physico - chemical and mechanical properties of different latex polymer films was studied.2- Preparation of latex polymer-modified cement mortar with different ratios of cement: latex polymer and different curing method.3- Solidification /stabilization (S/S) of electroplating heavy metal precipitate in latex polymer- modified mortar with different cement /electroplating heavy metal sludge ratio. chapter(III) results and discussion

Unraveling the mystery of natural rubber biosynthesis. Part II. Composition and growth of in vitro natural rubber using high-resolution size exclusion chromatography

Energy Technology Data Exchange (ETDEWEB)

Chiang, Cheng Ching K. [Univ. of Akron, OH (United States); Barkakaty, Balaka [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Puskas, Judit E. [Univ. of Akron, OH (United States); Xie, Wenshuang [The Ohio State Univ., Wooster, OH (United States); Cornish, Katrina [The Ohio State Univ., Wooster, OH (United States); Peruch, Federic [Univ. of Bordeaux, Pessac Cedex (France); Deffieux, Alain [Univ. of Bordeaux, Pessac Cedex (France)

2014-09-01

The superior properties of natural rubber (cis-1,4-polyisoprene [NR]) are a function of its structure and composition, properties that still remain a mystery and that are irreplaceable by any synthetic rubber. NR from guayule (Parthenium argentatum) has been gaining special interest for its hypoallergenic properties while maintaining superior mechanical properties that are commonly associated with the Brazilian rubber tree (Hevea brasiliensis), the most common source of NR. Techniques exist to isolate washed rubber particles (WRPs) that contain enzymatically active rubber transferase, to study NR biosynthesis, and previous work on the in vitroNRgrowth in Hevea has demonstrated the presence of around 50wt%of a low molecular weight ([MW], Mn <10 000 g/mol) fraction. Structural and compositional analyses of this low MW fraction in Hevea are challenging due to the high protein content. Here, we discuss the analysis and composition of guayule latex and WRPs using high-resolution Size Exclusion Chromatography. We also discuss the composition of the soluble fraction of inactive guayule latex using matrix-assisted laser desorption ionization/time of flight mass spectrometry.

Study on the Secant Segmentation Algorithm of Rubber Tree

Science.gov (United States)

Li, Shute; Zhang, Jie; Zhang, Jian; Sun, Liang; Liu, Yongna

2018-04-01

Natural rubber is one of the most important materials in the national defense and industry, and the tapping panel dryness (TPD) of the rubber tree is one of the most serious diseases that affect the production of rubber. Although considerable progress has been made in the more than 100 years of research on the TPD, there are still many areas to be improved. At present, the method of artificial observation is widely used to identify TPD, but the diversity of rubber tree secant symptoms leads to the inaccurate judgement of the level of TPD. In this paper, image processing technology is used to separate the secant and latex, so that we can get rid of the interference factors, get the exact secant and latex binary image. By calculating the area ratio of the corresponding binary images, the grade of TPD can be classified accurately. and can also provide an objective basis for the accurate identification of the tapping panel dryness (TPD) level.

Innovative Application of Biopolymer Keratin as a Filler of Synthetic Acrylonitrile-Butadiene Rubber NBR

OpenAIRE

Prochoń, Mirosława; Przepiórkowska, Anita

2013-01-01

The current investigations show the influence of keratin, recovered from the tanning industry, on the thermal and mechanical properties of vulcanizates with synthetic rubber acrylonitrile-butadiene rubber NBR. The addition of waste protein to NBR vulcanizates influences the improvement of resistance at high temperatures and mechanical properties like tensile strength and hardness. The introduction of keratin to the mixes of rubber previously blended with zinc oxide (ZnO) before vulcanization ...

Rubber - application of radiation to tire manufacture

International Nuclear Information System (INIS)

Hunt, J.D.; Alliger, G.

1979-01-01

Since the advent of commercial accelerators during the last several years capable of producing controllable electron beams of high energy, Firestone has devoted a considerable effort to the better understanding of the possible applications of such radiation to the production of tires or tire components. A number of chemical reactions can occur when elastomeric compounds are exposed to high energy waves, but crosslinking and degradation are the most important. The degree to which the crosslinking reaction predominates depends upon the nature of the rubber, compounding ingredients and the dosage. In general then, the effects achieved by the radiation of a rubber are quite similar to those resulting from heat. However, radiation cure or precure of compounds offers the advantage that the degree of crosslinking can be better controlled. Uniform crosslinking is possible since the high speed electrons penetrate uniformly throughout the sample. Curing with heat on the other hand may result in a greater degree of crosslinking on the surface of the sample than the center because of low heat conductivity. In general, radiation can be used to advantage to crosslink partially rubber tire components so that they retain better their shape and dimension during tire assembly and final cure or vulcanization. Added advantages of radiation precure include: a reduction of material usage, substitution of synthetic for natural rubber without loss in strength and the fact that partially crosslinked components will not thin out or become displaced during construction and vulcanization of the tire. (author)

Formation of protein complex with the aid of polyethylene glycol for deproteinized natural rubber latex

Science.gov (United States)

Wei, Lim Keuw; Ing, Wong Kwee; Badri, Khairiah Haji; Ban, Wong Chong

2013-11-01

The effect of polyethylene glycol (PEG) as a deproteinizing agent in commercial natural rubber latex (NRL) onto the physicochemical properties of the NRL was investigated. Three types of PEG were used namely PEG200, PEG4000 and PEG20000 (molecular weight of 200, 4000 and 20000 g/mol respectively). The optimum amount of PEG in NRL was determined from viscosity changes, protein content and Fourier Transform Infrared spectroscopy. Level of protein reduction was affected by molecular weight of PEG. The addition of PEG in NRL reduced the protein content of NRL (3.30 %) to the lowest (2.01 %) at 0.40 phr of PEG200 due to more attractive hydrophobic interactions between short chains PEG compared to PEG4000 (2.24%) and PEG20000 (2.15%). This was verified through FTIR spectroscopy analysis by observing the primary and secondary amide peak where PEG4000 has lesser absorption at the region compared to with PEG20000.

Amphiphilic semi-interpenetrating polymer networks using pulverized rubber

Science.gov (United States)

Shahidi, Nima

Scrap rubber materials provide a significant challenge to either reuse or safe disposal. Every year, millions of tires are discarded to landfills in the United States, consuming a staggering amount of land space, creating a high risk for large fires, breeding mosquitoes that spread diseases, and wasting the planet's natural resources. This situation cannot be sustained. The challenge of reusing scrap rubber materials is mainly due to the crosslinked structure of vulcanized rubber that prevent them from melting and further processing for reuse. The most feasible recycling approach is believed to be a process in which the vulcanized rubber is first pulverized into a fine powder and then incorporated into new products. The production of fine rubber particles is generally accomplished through the use of a cryogenic process that is costly. Therefore, development of a cost effective technology that utilizes a large quantity of the scrap rubber materials to produce high value added materials is an essential element in maintaining a sustainable solution to rubber recycling. In this research, a cost effective pulverization process, solid state shear extrusion (SSSE), was modified and used for continuous pulverization of the rubber into fine particles. In the modified SSSE process, pulverization takes place at high compressive shear forces and a controlled temperature. Furthermore, an innovative particle modification process was developed to enhance the chemical structure and surface properties of the rubber particles for manufacturing of high value added products. Modification of rubber particles was accomplished through the polymerization of a hydrophilic monomer mixture within the intermolecular structure of the hydrophobic rubber particles. The resulting composite particles are considered as amphiphilic particulate phase semi-interpenetrating polymer networks (PPSIPNs). The modified rubber particles are water dispersible and suitable for use in a variety of aqueous media

Development of rubber material for high radiation field

International Nuclear Information System (INIS)

Nakatsukasa, Sadayoshi; Tabasaki, Takeshi; Yoshida, Akihiro; Kadowaki, Yoshito

2013-01-01

Generally flexible polymeric materials exposed to radiation can't be used because they soften or harden remarkably in high radiation environment. Aromatic polymers such as PEEK, PI, and PES are also known as radiation-proof polymeric materials. Aromatic polymers are very hard, they can't be used for products like a packing where flexibility is required. We developed a new vulcanized rubber compound by the use of various additives and polymer blend. This developed rubber compound has a high radiation-proof performance by reaction balance of cross-linking and decomposition in this rubber. This rubber compound has a rubber elasticity even if exposed to radiation of MGy level, and its radiation proof is more than 5 times as high as conventional polymeric materials. This rubber compound is much more flexible than the aromatic polymers which are the used as conventional radiation-proof polymers. (author)

Mechanical properties of hexaferite based magnet composite of SrFe12019 and BaFe12O19 with natural rubber bonding agent

International Nuclear Information System (INIS)

Waluyo, T.; Herman, Y.A.; Sudirman; Ridwan

2000-01-01

Research on mechanical properties at magnet composite of SrFe 12 0 19 (SrM) and BaFe 12 O 19 (BaM)magnet powder with natural rubber bonding agent have been done. The natural rubber used was rubber made of latex without vulcanization, The SrM powder having average particle size of 1.6 μm and flat shaped. and the BaM powder having particle size of 1.2 μm and nodular shaped. The production of composite carried out in Labo Plastomill at 100 o C and mixer speed of 30 rpm for 7 minutes. The result obtained from Labo Plastomill then made into sheets. Mechanical properties of the composite tested were strain, elongation break and hardness, The results showed that the highest strain of the SrM composite obtained at composition of 70% vol of powder that is 2,22 MPa, and 3,84 MPa for BaM composite at 50% vol. of powder The elongation break of SrM composite decreased by increasing of powder volume fraction, that is 90% at the composition or 70% vol. of powder, and 370% for BaM composite at 50% vol. fraction of powder. The highest hardness for SrM composite obtained at composition of of 70% vol. of powder, that is 95 SHA. and for the BaM composite at 50% vol. of powder. that is 52 SHA

Simulation of curing of a slab of rubber

International Nuclear Information System (INIS)

Abhilash, P.M.; Kannan, K.; Varkey, Bijo

2010-01-01

The objective of the present work is to predict the degree of curing for a rectangular slab of rubber, which was subjected to non-uniform thermal history. As the thermal conductivity of rubber is very low, the temperature gradient across a slab is quite large, which leads to non-uniform vulcanization, and hence non-uniform mechanical properties-an inhomogeneous material. Since curing is an exothermic reaction, heat transfer and chemical reactions are solved in a coupled manner. The effect of heat generation on curing is also discussed.

Simulation of curing of a slab of rubber

Energy Technology Data Exchange (ETDEWEB)

Abhilash, P.M. [Department of Mechanical Engineering, IIT Madras, Chennai 600036 (India); Kannan, K., E-mail: krishnakannan@iitm.ac.i [Department of Mechanical Engineering, IIT Madras, Chennai 600036 (India); Varkey, Bijo [Advanced Design Department, MRF Ltd., Chennai 600019 (India)

2010-04-15

The objective of the present work is to predict the degree of curing for a rectangular slab of rubber, which was subjected to non-uniform thermal history. As the thermal conductivity of rubber is very low, the temperature gradient across a slab is quite large, which leads to non-uniform vulcanization, and hence non-uniform mechanical properties-an inhomogeneous material. Since curing is an exothermic reaction, heat transfer and chemical reactions are solved in a coupled manner. The effect of heat generation on curing is also discussed.

Biorefinery methods for separation of protein and oil fractions from rubber seed kernel

NARCIS (Netherlands)

Widyarani, R.; Ratnaningsih, E.; Sanders, J.P.M.; Bruins, M.E.

2014-01-01

Biorefinery of rubber seeds can generate additional income for farmers, who already grow rubber trees for latex production. The aim of this study was to find the best method for protein and oil production from rubber seed kernel, with focus on protein recovery. Different pre-treatments and oil

Aspectos históricos da vulcanização Historical aspects of vulcanization

Directory of Open Access Journals (Sweden)

Helson M. da Costa

2003-06-01

Full Text Available As borrachas, para serem convertidas em materiais úteis do ponto de vista de aplicações, precisam ser misturadas a alguns ingredientes, os quais vão lhes dar as características desejadas para, então, serem vulcanizadas. Neste artigo, os aspectos históricos da vulcanização são abordados bem como a evolução dos aditivos essenciais à maioria das formulações.Rubbers, to be turned into useful materials from the commercial applications point of view, need the addition of a few other ingredients which, upon vulcanization, will impart the desired characteristics to the material. In this paper, historical aspects of vulcanization are revised as well as the evolution of the additives used in most of the formulations.

Latex medical gloves

DEFF Research Database (Denmark)

Palosuo, Timo; Antoniadou, Irini; Gottrup, Finn

2011-01-01

Many hospitals have implemented policies to restrict or ban the use of devices made of natural rubber latex (NRL) in healthcare as precautionary measures against the perceived risk of NRL allergy. Changes in glove technology, progress in measuring the specific allergenic potential of gloves...... properties of NRL and synthetic gloves and the role of glove powder. The review shows that NRL medical gloves, when compared with synthetic gloves, tend to be stronger, more flexible and better accepted by clinicians. The introduction of powder-free gloves has been associated with reductions in protein...

Electron spectroscopy of rubber and resin-based composites containing 2D carbon

International Nuclear Information System (INIS)

Kaciulis, S.; Mezzi, A.; Balijepalli, S.K.; Lavorgna, M.; Xia, H.S.

2015-01-01

Composite materials with 2D carbon (graphene and/or single wall carbon nanotubes) are very promising due to their extraordinary electrical and mechanical properties. Graphene and natural rubber composites, which may be used for the gaskets or sealants, were prepared by ultrasonically assisted latex-mixing exfoliation and in-situ reduction process, with two vulcanization approaches: roll-mixing and hot-pressing. Also the resin-based composites, filled with micro-particles of Ag and graphene or carbon nanotubes, have been studied. The standards for the compositional characterization of these materials still are not established. In addition to the mostly used techniques, such as Raman spectroscopy and electron microscopy, also Auger electron spectroscopy can be employed for the identification of graphene. In this study, the shape of C KVV peak, excited by electron beam and X-ray photons, has been investigated in different composite materials containing graphene and carbon nanotubes. A spectroscopic method for 2D carbon recognition, based on the D x parameter which is determined from C KVV signal excited by X-ray photons, was proposed and verified. Even a small content of graphene in different types of composites was sufficient for this recognition due to the dominating presence of graphene on the surface of composites. - Highlights: • Chemical composition of the rubber composites was determined by XPS. • Auger spectrum of carbon was used for graphene identification in composites. • Small content of graphene was sufficient for its recognition from the D parameter

Electron spectroscopy of rubber and resin-based composites containing 2D carbon

Energy Technology Data Exchange (ETDEWEB)

Kaciulis, S., E-mail: saulius.kaciulis@ismn.cnr.it [Institute for the Study of Nanostructured Materials, ISMN-CNR, P.O. Box 10, Monterotondo Stazione, 00015 Roma (Italy); Mezzi, A.; Balijepalli, S.K. [Institute for the Study of Nanostructured Materials, ISMN-CNR, P.O. Box 10, Monterotondo Stazione, 00015 Roma (Italy); Lavorgna, M. [Institute of Polymers, Composites and Biomaterials, IPCB-CNR, P.le Fermi, 80055 Napoli (Italy); Xia, H.S. [State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, 610065 Sichuan (China)

2015-04-30

Composite materials with 2D carbon (graphene and/or single wall carbon nanotubes) are very promising due to their extraordinary electrical and mechanical properties. Graphene and natural rubber composites, which may be used for the gaskets or sealants, were prepared by ultrasonically assisted latex-mixing exfoliation and in-situ reduction process, with two vulcanization approaches: roll-mixing and hot-pressing. Also the resin-based composites, filled with micro-particles of Ag and graphene or carbon nanotubes, have been studied. The standards for the compositional characterization of these materials still are not established. In addition to the mostly used techniques, such as Raman spectroscopy and electron microscopy, also Auger electron spectroscopy can be employed for the identification of graphene. In this study, the shape of C KVV peak, excited by electron beam and X-ray photons, has been investigated in different composite materials containing graphene and carbon nanotubes. A spectroscopic method for 2D carbon recognition, based on the D{sub x} parameter which is determined from C KVV signal excited by X-ray photons, was proposed and verified. Even a small content of graphene in different types of composites was sufficient for this recognition due to the dominating presence of graphene on the surface of composites. - Highlights: • Chemical composition of the rubber composites was determined by XPS. • Auger spectrum of carbon was used for graphene identification in composites. • Small content of graphene was sufficient for its recognition from the D parameter.

[Total analysis of organic rubber additives].

Science.gov (United States)

He, Wen-Xuan; Robert, Shanks; You, Ye-Ming

2010-03-01

In the present paper, after middle pressure chromatograph separation using both positive phase and reversed-phase conditions, the organic additives in ethylene-propylene rubber were identified by infrared spectrometer. At the same time, by using solid phase extraction column to maintain the main component-fuel oil in organic additves to avoid its interfering with minor compounds, other organic additves were separated and analysed by GC/Ms. In addition, the remaining active compound such as benzoyl peroxide was identified by CC/Ms, through analyzing acetone extract directly. Using the above mentioned techniques, soften agents (fuel oil, plant oil and phthalte), curing agent (benzoylperoxide), vulcanizing accelerators (2-mercaptobenzothiazole, ethyl thiuram and butyl thiuram), and antiagers (2, 6-Di-tert-butyl-4-methyl phenol and styrenated phenol) in ethylene-propylene rubber were identified. Although the technique was established in ethylene-propylene rubber system, it can be used in other rubber system.

Effect of Amphiphilic Alkyl Chain Length Upon Purified LATEX Stability

International Nuclear Information System (INIS)

Amira Amir Hassan; Amir Hashim Mohd Yatim

2015-01-01

Rubber particles in purified latex (PL) are stabilized by a film of protein and fatty acid soap (surfactant). Saturated straight-chain fatty acid soaps can assist an enhancement of latex stability. However, whether the alkyl chain length plays an important role in increasing the stability is still an issue. The aim of this study is to investigate the effect of alkyl chain length of anionic surfactant on the stability of purified latex. The fatty acid soap of decanoate (9), laurate (11), sodium dodecyl sulphate (SDS) (12) and palmitate (15) were used. The numbers in parentheses indicating the number of carbon present in alkyl chain of the soap. The results showed that the impact of alkyl chain length on the stability of latex is in the order of laurate > decanoate > SDS > palmitate > purified latex accordingly. The alkyl chain length does giving a significant effect on latex stability after longer stirring time. The particle size of latex with the presence of surfactant is greater compare to a single particle itself due to extension of particles diameter. Thus suitable interaction of the nonpolar tail of surfactant with the hydrophobic regions of latex surface played a major role in maintaining a stable latex system. (author)

Highly toughened polypropylene/ethylene–propylene-diene monomer/zinc dimethacrylate ternary blends prepared via peroxide-induced dynamic vulcanization

Energy Technology Data Exchange (ETDEWEB)

Chen, Yukun, E-mail: cyk@scut.edu.cn [The Key Laboratory of Polymer Processing Engineering, Ministry of Education, South China University of Technology, Guangzhou 510640 (China); School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640 (China); Xu, Chuanhui [College of Material Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Cao, Liming [The Key Laboratory of Polymer Processing Engineering, Ministry of Education, South China University of Technology, Guangzhou 510640 (China); School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640 (China); Cao, Xiaodong [College of Material Science and Engineering, South China University of Technology, Guangzhou 510640 (China)

2013-02-15

Polypropylene (PP)/ethylene–propylene-diene monomer (EPDM)/zinc dimethacrylate (ZDMA) blends with remarkable toughness and extensibility were successfully prepared via peroxide dynamical vulcanization. A unique structure with the EPDM particles surrounded by a transition zone containing numerous polymerized ZDMA (PZDMA) nano-particles was observed for the first time by using transmission electron microscopy (TEM) examination, which contributed to the dramatically increase of Izod impact strength. Dynamic mechanical analysis (DMA) confirmed that the possible PZDMA graft products resulted from peroxide dynamical vulcanization improved the compatibility between EPDM and PP phases. The specific morphology of the PP/EPDM/ZDMA blends indicated that ZDMA can lead to size reduction and good distribution uniformity of the crosslinked rubber particles and the increase of adhesion between PP matrix and EPDM phases during deformation. The synergic effect of the increase in the effective volume of the EPDM phase, the improved compatibility and adhesion between EPDM and PP phases and the deformation of those fine rubber particles is believed to result in the remarkable high toughness and extensibility of the PP/EPDM/ZDMA blends. Particularly for the PP/EPDM ratio of 70/30, the PP/EPDM/ZDMA (70/30/9, w/w/w) ternary blends with the Izod impact strength nearly 2 times higher than PP/EPDM (70/30, w/w) binary blends and 15–20 times higher than PP are achieved; besides, the elongation at break of PP/EPDM/ZDMA ternary blends is 4–5 times higher than that of PP/EPDM binary blends. - Highlights: ► ZDMA largely toughen peroxide dynamically vulcanized PP/EPDM blend. ► PZDMA graft products improved the compatibility and adhesion between EPDM and PP. ► Size reduction and good distribution uniformity of crosslinked rubber particles.

Highly toughened polypropylene/ethylene–propylene-diene monomer/zinc dimethacrylate ternary blends prepared via peroxide-induced dynamic vulcanization

International Nuclear Information System (INIS)

Chen, Yukun; Xu, Chuanhui; Cao, Liming; Cao, Xiaodong

2013-01-01

Polypropylene (PP)/ethylene–propylene-diene monomer (EPDM)/zinc dimethacrylate (ZDMA) blends with remarkable toughness and extensibility were successfully prepared via peroxide dynamical vulcanization. A unique structure with the EPDM particles surrounded by a transition zone containing numerous polymerized ZDMA (PZDMA) nano-particles was observed for the first time by using transmission electron microscopy (TEM) examination, which contributed to the dramatically increase of Izod impact strength. Dynamic mechanical analysis (DMA) confirmed that the possible PZDMA graft products resulted from peroxide dynamical vulcanization improved the compatibility between EPDM and PP phases. The specific morphology of the PP/EPDM/ZDMA blends indicated that ZDMA can lead to size reduction and good distribution uniformity of the crosslinked rubber particles and the increase of adhesion between PP matrix and EPDM phases during deformation. The synergic effect of the increase in the effective volume of the EPDM phase, the improved compatibility and adhesion between EPDM and PP phases and the deformation of those fine rubber particles is believed to result in the remarkable high toughness and extensibility of the PP/EPDM/ZDMA blends. Particularly for the PP/EPDM ratio of 70/30, the PP/EPDM/ZDMA (70/30/9, w/w/w) ternary blends with the Izod impact strength nearly 2 times higher than PP/EPDM (70/30, w/w) binary blends and 15–20 times higher than PP are achieved; besides, the elongation at break of PP/EPDM/ZDMA ternary blends is 4–5 times higher than that of PP/EPDM binary blends. - Highlights: ► ZDMA largely toughen peroxide dynamically vulcanized PP/EPDM blend. ► PZDMA graft products improved the compatibility and adhesion between EPDM and PP. ► Size reduction and good distribution uniformity of crosslinked rubber particles

Latex allergy and occupational asthma in health care workers: adverse outcomes.

OpenAIRE

Amr, Sania; Bollinger, Mary E.

2004-01-01

The prevalence of natural rubber latex (NRL) allergy has been estimated to be 5-18% in health care workers, and latex exposure has been one of the leading causes of occupational asthma in the last several years. We present the cases of two nurses who developed sensitivity to NRL, both with dermatologic symptoms and respiratory symptoms that included asthma. They were referred to the University of Maryland for evaluation of their allergies, then for occupational and environmental consults. The...

Effect of magnetic and thermal properties of iron oxide nanoparticles (IONs) in nitrile butadiene rubber (NBR) latex

Science.gov (United States)

Ong, Hun Tiar; Julkapli, Nurhidayatullaili Muhd; Hamid, Sharifah Bee Abd; Boondamnoen, O.; Tai, Mun Foong

2015-12-01

Nitrile butadiene rubber (NBR) gloves are one of the most important personal protective equipments but they are possible to tear off and contaminate food or pharmaceutical and healthcare products during manufacturing and packaging process. High tendency of torn glove remaining in food or products due to white or light flesh-coloured glove is not easy to be detected by naked eyes. In this paper, iron oxide nanoparticles (IONs) selected as additive for NBR to improve its detectability by mean of magnetic properties. IONs synthesized via precipitation method and compounded with NBR latex before casting on petri dish. The properties of IONs were investigated by X-ray Diffractometry (XRD), Transmission Electron Microscope (TEM), Raman Spectroscopy and Vibrating Sample Magnetometer (VSM). Meanwhile NBR/IONs composites were studied by Thermogravimetry Analysis (TGA), Differential Scanning Calorimetry (DSC) and Vibrating Sample Magnetometer (VSM). It observed that, synthesized IONs shows of 25.28 nm crystallite with 25.86 nm semipherical (changed as) shape. Meanwhile, Magnetite and maghemite phase are found in range of 670 cm-1 and 700 cm-1 respectively, which it contributes magnetization saturation of 73.96 emu/g at 10,000 G by VSM. Thermal stability and magnetic properties were increased with incorporating IONs into NBR latex up to 20 phr. NBR/IONs 5 phr has the optimum thermal stability, lowest glass transition temperature (-14.83 °C) and acceptable range of magnetization saturation (3.83 emu/g at 10,000 G) to form NBR gloves with magnetic detectability.

High Performance Graphene Oxide Based Rubber Composites

Science.gov (United States)

Mao, Yingyan; Wen, Shipeng; Chen, Yulong; Zhang, Fazhong; Panine, Pierre; Chan, Tung W.; Zhang, Liqun; Liang, Yongri; Liu, Li

2013-01-01

In this paper, graphene oxide/styrene-butadiene rubber (GO/SBR) composites with complete exfoliation of GO sheets were prepared by aqueous-phase mixing of GO colloid with SBR latex and a small loading of butadiene-styrene-vinyl-pyridine rubber (VPR) latex, followed by their co-coagulation. During co-coagulation, VPR not only plays a key role in the prevention of aggregation of GO sheets but also acts as an interface-bridge between GO and SBR. The results demonstrated that the mechanical properties of the GO/SBR composite with 2.0 vol.% GO is comparable with those of the SBR composite reinforced with 13.1 vol.% of carbon black (CB), with a low mass density and a good gas barrier ability to boot. The present work also showed that GO-silica/SBR composite exhibited outstanding wear resistance and low-rolling resistance which make GO-silica/SBR very competitive for the green tire application, opening up enormous opportunities to prepare high performance rubber composites for future engineering applications. PMID:23974435

Adhesion of nitrile rubber (NBR) to polyethylene terephthalate (PET) fabric. Part 1: PET surface modification by methylenediphenyl di-isocyanate (MDI)

International Nuclear Information System (INIS)

Razavizadeh, Mahmoud; Jamshidi, Masoud

2016-01-01

Graphical abstract: - Highlights: • Glutaric anhydride peroxide (GAP) was grafted on PET surface by UV irradiation method. Then MDI was attached to GAP on PET surface. • The fabric was vulcanized by nitrile rubber. • Peet test was performed after each stage of surface modification. • Curing temperature was increased and the tests were repeated. • Effect of MDI coating on PET without carboxylation was evaluated. Effect of vulcanizing temperature on this product was also studied. - Abstract: Fiber to rubber adhesion is an important subject in rubber composite industry. It is well known that surface physical, mechanical and chemical treatments are effective methods to improve interfacial bonding. Ultra violet (UV) light irradiation is an efficient method which is used to increase interfacial interactions. In this research UV assisted chemical modification of PET fabric was used to increase its bonding to nitrile rubber (NBR). NBR is perfect selection to produce fuel and oil resistant rubber parts but it has weak bonding to fabrics. For this purpose at first, the PET fabric was carboxylated under UV irradiation and then methylenediphenyl diisocyanate (MDI) was reacted and grafted to carboxylated PET. T-peel test was used to evaluate PET fabric to NBR bonding strength. Attenuated total reflectance-Fourier transform infrared spectroscopy (FTIR-AT) was used to assess surface modifications of the PET fabrics. The chemical composition of the PET surfaces before and after carboxylation and MDI grafting was investigated by X-ray photoelectron spectroscopy (XPS). It was found that at vulcanizing temperature of 150 °C, carboxylation in contrary to MDI grafting, improved considerably PET to NBR adhesion. Finally effect of curing temperature on PET to NBR bonding strength was determined. It was found that increasing vulcanizing temperature to 170 °C caused considerable improvement (about 134%) in bonding strength.

Natural rubber (NR) biosynthesis: perspectives from polymer chemistry

Energy Technology Data Exchange (ETDEWEB)

Barkakaty, Balaka [ORNL

2014-01-01

Natural rubber is an important strategic raw material for manufacturing a wide variety of industrial products. There are at least 2,500 different latex-producing plant species; however, only Hevea brasiliensis (the Brazilian rubber tree) is a commercial source. The chemical structure of natural rubber is cis-1,4-polyisoprene, but the exact structure of the head and end groups remains unknown. Since synthetic cis-1,4-polyisoprenes cannot match the superior properties of natural rubber, understanding the chemistry behind the biosynthetic process is key to finding a possible replacement. T his chapter summarizes our current understandings from the perspective of a polymer scientist by comparing synthetic polyisoprenes to natural rubber. The chapter also highlights biomimetic polymerization, research towards a synthetic match of natural rubber and the role of natural rubber in health care.

Styrene-butadiene rubber/halloysite nanotubes nanocomposites modified by methacrylic acid

International Nuclear Information System (INIS)

Guo Baochun; Lei Yanda; Chen Feng; Liu Xiaoliang; Du Mingliang; Jia Demin

2008-01-01

Methacrylic acid (MAA) was used to improve the performance of styrene-butadiene rubber (SBR)/halloysite nanotubes (HNTs) nanocomposites by direct blending. The detailed interaction mechanisms of MAA and the in situ formed zinc methacrylate (ZDMA) were revealed by X-ray diffraction (XRD), surface area and porosity analysis, X-ray photoelectron spectroscopy (XPS) together with crosslink density determination. The strong interfacial bonding between HNTs and rubber matrix is resulted through ZDMA and MAA intermediated linkages. ZDMA connects SBR and HNTs via grafting/complexation mechanism. MAA bonds SBR and HNTs through grafting/hydrogen bonding mechanism. Significantly improved dispersion of HNTs in virtue of the interactions between HNTs and MAA or ZDMA was achieved. Effects of MAA content on the vulcanization behavior, morphology and mechanical properties of the nanocomposites were investigated. Promising mechanical properties of MAA modified SBR/HNTs nanocomposites were obtained. The changes in vulcanization behavior, mechanical properties and morphology were correlated with the interactions between HNTs and MAA or ZDMA and the largely improved dispersion of HNTs

Styrene-butadiene rubber/halloysite nanotubes nanocomposites modified by methacrylic acid

Energy Technology Data Exchange (ETDEWEB)

Guo Baochun [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China)], E-mail: psbcguo@scut.edu.cn; Lei Yanda; Chen Feng; Liu Xiaoliang; Du Mingliang; Jia Demin [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China)

2008-12-30

Methacrylic acid (MAA) was used to improve the performance of styrene-butadiene rubber (SBR)/halloysite nanotubes (HNTs) nanocomposites by direct blending. The detailed interaction mechanisms of MAA and the in situ formed zinc methacrylate (ZDMA) were revealed by X-ray diffraction (XRD), surface area and porosity analysis, X-ray photoelectron spectroscopy (XPS) together with crosslink density determination. The strong interfacial bonding between HNTs and rubber matrix is resulted through ZDMA and MAA intermediated linkages. ZDMA connects SBR and HNTs via grafting/complexation mechanism. MAA bonds SBR and HNTs through grafting/hydrogen bonding mechanism. Significantly improved dispersion of HNTs in virtue of the interactions between HNTs and MAA or ZDMA was achieved. Effects of MAA content on the vulcanization behavior, morphology and mechanical properties of the nanocomposites were investigated. Promising mechanical properties of MAA modified SBR/HNTs nanocomposites were obtained. The changes in vulcanization behavior, mechanical properties and morphology were correlated with the interactions between HNTs and MAA or ZDMA and the largely improved dispersion of HNTs.

Ten years incidence of natural rubber latex sensitization and symptoms in a prospective cohort of health care workers using non-powdered latex gloves 2000-2009.

Science.gov (United States)

Larese Filon, Francesca; Bochdanovits, Letizia; Capuzzo, Chiara; Cerchi, Roberto; Rui, Francesca

2014-07-01

To assess the incidence of sensitization and gloves-related symptoms in 10-year follow-up in a group of health care workers (9,660 person-years) using non-powdered latex gloves from 2000 to 2009 and to examine related factors. We studied 2,053 health care workers in Trieste Hospitals by means of skin prick test for latex extract, patch tests and medical examinations. We report the incidence of latex sensitization among workers using non-powdered latex gloves. The incidence of latex sensitization, rhinitis, asthma, urticaria, irritant and allergic contact dermatitis were 1.0; 0.12; 0.21; 0.72; 2.39 and 2.50 cases per 1,000 person-years, respectively. Respiratory symptoms and urticaria were positively related with latex sensitization (OR = 8.0; 95 % CL 1.27-48.6), with common allergic respiratory symptoms (OR = 4.19; 95 % CL 1.04-16.8) and with familial atopy (OR = 4.47; 95 % CL 1.1-17.9). The incidence of latex sensitization and latex-related symptoms were very low but subjects with allergic symptoms related to common allergens are at higher risk. The use of non-latex gloves is suggested for them.

Effect of gamma irradiation on the properties of natural rubber/styrene butadiene rubber blends

Directory of Open Access Journals (Sweden)

A.B. Moustafa

2016-09-01

Full Text Available Blends of natural rubber (NR with styrene butadiene rubber (SBR with varying ratios have been prepared. Vulcanization of the prepared blends has been induced by irradiation of gamma rays with varying doses up to 250 kGy. Mechanical properties, namely tensile strength, tensile modulus at 100% elongation, elongation at break have been followed up as a function of irradiation dose as well as blend composition. Physical properties, namely gel fraction and swelling number have been followed up using benzene as a solvent. Thermal measurements namely thermogravimetric analysis were carried out. The results indicated that the addition of NR has improved the properties of NR / SBR blends. Also NR/SBR blend is thermally stable than NR alone.

Intercomparison of Methods for Determination of Resonant Frequency Shift of a Microstrip Patch Antenna Loaded with Hevea Rubber Latex

Directory of Open Access Journals (Sweden)

Nor Zakiah Yahaya

2014-01-01

Full Text Available This paper presents an intercomparison between the finite element method, method of moment, and the variational method to determine the effect of moisture content on the resonant frequency shift of a microstrip patch loaded with wet material. The samples selected for this study were Hevea rubber latex with different percentages of moisture content from 35% to 85%. The results were compared with the measurement data in the frequency range between 1 GHz and 4 GHz. It was found that the finite element method is the most accurate among all the three computational techniques with 0.1 mean error when compared to the measured resonant frequency shift. A calibration equation was obtained to predict moisture content from the measured frequency shift with an accuracy of 2%.

Economic assessment of possible electron accelerator applications in curing silicon rubber based electric installation material

International Nuclear Information System (INIS)

Rmot, L.

1976-01-01

A description is given of the conventional technology of production of conductors with silicon rubber insulation and of the radiation vulcanization method, i.e., the radiation cross-linking of silicon rubber. An economic comparison is shown for both technologies. The analysis shows that the indices for the radiation cross-linking technology are favourable and that the introduction thereof would be advantageous. (J.P.)

Utilization of surface-treated rubber particles from waste tires

Energy Technology Data Exchange (ETDEWEB)

Smith, F.G. [Argonne National Lab., IL (United States). Energy Systems Div.]|[Environmental Technologies Alternatives, Inc., Lima, OH (United States)

1994-12-01

During a 12-month program, the author successfully demonstrated commercial applications for surface-treated rubber particles in two major markets: footwear (shoe soles and components) and urethane-foam carpet underlay (padding). In these markets, he has clearly demonstrated the ease of using R-4080 and R-4030 surface-treated rubber particles in existing manufacturing plants and processes and have shown that the material meets or exceeds existing standards for performance, quality, and cost-effectiveness. To produce R-4080 and R-4030, vulcanized rubber, whole-tire material is finely ground to particles of nominal 80 and mesh size respectively. Surface treatment is achieved by reacting these rubber particles with chlorine gas. In this report, the author describes the actual test and evaluations of the participant companies, and identifies other potential end uses.

Compatibilization efficiency of carboxylated nitrile rubber and epoxy pre-polymer in nitrile/acrylic rubber blends

Directory of Open Access Journals (Sweden)

Micheli L. Celestin

2013-01-01

Full Text Available An investigation has been made of the effects from a compatibilizer, viz. carboxylated nitrile rubber (XNBR, on several properties of nitrile rubber (NBR and acrylic rubber (ACM blends, including curing characteristics, mechanical, dynamic mechanical and dielectric properties. The presence of XNBR until 10 phr resulted in an improvement of the ultimate tensile properties, especially elongation at break. The mechanical properties associated to the volume fraction of rubber in the network (Vr and torque values suggest the co-vulcanization phenomenon imparted by the compatibilization. The oil resistance of NBR/ACM (50:50 wt. (% blends (compatibilized and non compatibilized was similar to that observed for pure ACM and significantly higher than NBR. The addition of small amounts of epoxy pre-polymer in combination with XNBR resulted in an additional improvement of the tensile properties. The dynamic mechanical and dielectric properties of the blends were also investigated. The loss modulus values of the compatibilized blends were significantly lower indicating an increase of the elastic characteristics. All blends presented two dielectric relaxation peaks confirming the heterogeneity of the compatibilized blends

Interfacial interaction between the epoxidized natural rubber and silica in natural rubber/silica composites

Science.gov (United States)

Xu, Tiwen; Jia, Zhixin; Luo, Yuanfang; Jia, Demin; Peng, Zheng

2015-02-01

The epoxidized natural rubber (ENR) as an interfacial modifier was used to improve the mechanical and dynamical mechanical properties of NR/silica composites. In order to reveal the interaction mechanism between ENR and silica, the ENR/Silica model compound was prepared by using an open mill and the interfacial interaction of ENR with silica was investigated by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), X-ray diffraction (XRD) and stress-strain testing. The results indicated that the ring-opening reaction occurs between the epoxy groups of ENR chains and Si-OH groups on the silica surfaces and the covalent bonds are formed between two phases, which can improve the dispersion of silica in the rubber matrix and enhance the interfacial combination between rubber and silica. The ring-opening reaction occurs not only in vulcanization process but also in mixing process, meanwhile, the latter seems to be more important due to the simultaneous effects of mechanical force and temperature.

USED IN THE MANUFACTURE OF EMULSION RUBBER WASTE OF SUGAR MANUFACTURE – MOLASSES

Directory of Open Access Journals (Sweden)

S. S. Nikulin

2015-01-01

Full Text Available Currently, much attention is paid to development, allowing use of waste and by-products formed during certain manufacturing processes. This allows you to either reduce or completely eliminate the use of valuable and expensive raw materials. The use of this raw material in the production of synthetic rubber will not only reduce the cost of coagulation and acidifying agents, but also to improve the environmental situation. Featured in some cases effective coalescing agents based on polymeric quaternary ammonium salts (PCHSA have a high coagulating power, and hence low consumption of the allocation of the rubber latex (3-5 kg0t-1 rubber. Scarcity and high cost of these drugs leads to higher prices resulting rubber. Furthermore it is known that the application requires keeping PCHSA sufficiently precise dosage administered substances by the action of a latex, owing to the high capacity of the antiseptic may lead to discharge into natural waters polluted waters. However, using as the coagulating agent departing sugar production molasses solves a number of problematic steps in the production of synthetic rubber. First, a well-studied effective coagulation effect of different nitrogen derivatives relating to cationic surfactants. In freshly prepared solutions of molasses contained about 9 wt%, and this value increases significantly during enzymatic fermentation. Secondly, highly acidic environment of aqueous solutions of molasses after storage can allow their use in addition to or instead of the sulfuric acid used in large amounts (up to 15 kg m-1 rubber technology selection tests carried found that vulcanizates derived from rubber samples isolated molasses, consistent with the requirements and were similar to control samples prepared from the latex using sodium chloride.

Latex allergy: new insights to explain different sensitization profiles in different risk groups.

Science.gov (United States)

Peixinho, C; Tavares-Ratado, P; Tomás, M R; Taborda-Barata, L; Tomaz, C T

2008-07-01

Differences in latex allergen sensitization profiles have been described between children subjected to repetitive surgical interventions and health care workers (HCW). 'Major' allergens for patients with spina bifida are Hev b 1, 3 and 7, while for HCW, 'major' allergens are Hev b 2, 5, 6.01 and 13. The reason for these differential sensitization profiles is currently unknown. To investigate latex allergen profiles on internal and external surfaces of natural rubber latex gloves. Eighty-two samples of commonly used surgical gloves (41 glove brands) were used for analysis. Specific allergen levels of Hev b 1, 3, 5 and 6.02 on both surfaces of the gloves were quantified using an enzyme immunometric assay, a FITkit (FIT Biotech, Tampere, Finland). Differences in allergen levels were observed between internal and external surfaces of all glove types. Concentrations of Hev b 1 and Hev b 3 were significantly higher on external surfaces, while internal surfaces had higher allergen levels of Hev b 5 and Hev b 6.02. Analysis of surgical and examination gloves, powdered and nonpowdered gloves also showed that the content of Hev b 5 and Hev b 6.02 was significantly higher on internal surfaces while that of Hev b 1 and Hev b 3 was higher on external surfaces. Our study showed different allergen profiles on internal and external surfaces of natural rubber latex gloves. These results may suggest a relationship between latex allergen localization and sensitization routes in different risk groups.

Dielectric properties of various polymers (PVC, EVA, HDPE, and PP) reinforced with ground tire rubber (GTR)

OpenAIRE

Mujal Rosas, Ramón María; Marín Genescá, Marcos; Ballart Prunell, Jordi

2015-01-01

Mass production of tires as well as its difficult storage or elimination is a real environmental problem. Various methods for recycling tires are currently used, such as mechanical crushing, which puts vulcanized rubber, steel, and fibers apart. The rubber may be used in several industrial applications such as flooring, insulations, and footwear. The present paper focuses on finding a new application for old used tires [ground tire rubber (GTR)]. To this end, tires dust has been mixed with va...

Combination of Tung oil and Natural Rubber Latex in PVA as Water Based Coatings for Paperboard Application

Directory of Open Access Journals (Sweden)

Jianprasert Apichaya

2015-01-01

Full Text Available This research is focused on the preparation of the PVA/TO/NRL coatings for paperboard by using poly(vinyl alcohol (PVA as substance and blending with Tung oil (TO and/or natural rubber latex (NRL in order to enhance water resistance and dynamic mechanical properties. The effects of TO: NRL ratios on the structures were investigated by water resistance property and dynamic mechanical thermal analysis (DMA. The results showed that the water resistance property was improved by crosslinking of TO and film forming of NRL. The PVA/TO/NRL coating containing both TO and NRL gave better thermal behavior than those with only TO or NRL. For paperboard application, the PVA/TO/NRL coatings were applied on the paperboard to study water affinity and absorption rate on the coated surface. The rate of contact angle change of water on coated paperboards decreased depending on the ratios of TO and NRL.

Latex production with depolymerizing compounds of actin cytoskeleton in rubber trees Produção de látex estimulada pela aplicação de compostos despolimerizantes de citoesqueleto de actina em seringueiras

Directory of Open Access Journals (Sweden)

Gao Zheng-Quan

2008-02-01

Full Text Available The objective of this work was to assess stimulated latex flow from rubber trees (Hevea brasiliensis with saturated macrolide (latrunculin A, 1, 5, and 10% potassium iodide in 2% methylcellulose compared with 0.3% ethylene in 2% methylcellulose (check and 2% methylcellulose (blank. Latex output and contents of pure rubber, total solid, sucrose, inorganic phosphorus, thiol, and Mg2+ were measured. The treatments containing 1% KI or saturated macrolide increased latex yields compared to the blank with 2% methylcellulose alone. The 1% KI or saturated macrolide treatments were equal to that of 0.3% ethylene check treatment. However, 5 and 10% KI were harmful to bark of rubber trees, even caused prolonged tapping panel dryness.O objetivo deste trabalho foi avaliar a produção de látex em seringueiras (Hevea brasiliensis estimulada pela aplicação de macrolídeo saturado (latrunculina A, iodeto de potássio a 1, 5 e 10%, e etileno a 0,3%, preparados em solução de metilcelulose a 0,2%. O tratamento testemunha consistiu da aplicação de solução pura de metilcelulose a 2%. Foram medidos a produção de látex e o conteúdo de borracha pura, sólidos totais, sacarose, fósforo inorgânico, tiol e Mg2+. A aplicação de KI a 1% ou de macrolídeo saturado aumentou a produção de látex em comparação com o tratamento testemunha. Os tratamentos com KI a 1% e macrolídeo saturado foram iguais ao tratamento com etileno a 0,3%. No entanto, os tratamentos com KI a 5 e 10% foram prejudiciais à casca da seringueira, causando até mesmo o secamento do painel-de-sangria.

Crosslinked bicontinuous biobased PLA/NR blends via dynamic vulcanization using different curing systems.

Science.gov (United States)

Yuan, Daosheng; Chen, Kunling; Xu, Chuanhui; Chen, Zhonghua; Chen, Yukun

2014-11-26

In this study, blends of entirely biosourced polymers, namely polylactide (PLA) and natural rubber (NR), were prepared through dynamic vulcanization using dicumyl peroxide (DCP), sulphur (S) and phenolic resin (2402) as curing agents, respectively. The crosslinked NR phase was found to be a continuous structure in all the prepared blends. The molecular weight changes of PLA were studied by gel permeation chromatography. Interfacial compatibilization between PLA and NR was investigated using Fourier transform infrared spectroscopy and scanning electron microscopy. The thermal properties of blends were evaluated by differential scanning calorimetry and thermogravimetric analysis instrument. It was found that the molecular weight of PLA and interfacial compatibilizaion between PLA and NR showed a significant influence on the mechanical and thermal properties of blends. The PLA/NR blend (60/40 w/w) by DCP-induced dynamic vulcanization owned the finest mechanical properties and thermal stability. Copyright © 2014 Elsevier Ltd. All rights reserved.

On some peculiarities of oil-resisting rubbers production from nitrile rubber of different composition by the use of Co60 gamma irradiation

International Nuclear Information System (INIS)

Mamedov, Sh.M.; Nelikzade, M.M.; Mamedov, A.A.

1976-01-01

The physicomechanical properties and swelling of vulcanizates were studied by means of radiation vulcanization. The test samples were preheated and formed by a press at 154 deg C for 3 min. Irradiation was performed in atmosphere on 60 Co (dosage 0.48 Mrad/hr). Irradiation caused decrease in tensile strength, as well as relative and permanent elongation; at the same time it considerably strengthened rubber hardness. All the rubber samples showed greater strength after irradiation under 5.7-13.8 Mrad. Depending on the dosage (3.6-13.8 Mrad), the relative and permanent elongation of vulcanizates obtained with the aid of altax was found to decrease, while strength and swelling increased. The swelling of rubber samples obtained with thiurad and thiuradaltax compounds decreased. Hence the advisability of using that rubber for manufacture of petroleum-resistant products

Physico-mecha-nical properties of rubber seed shell carbon – filled natural rubber compounds

Directory of Open Access Journals (Sweden)

L.O. Ekebafe

2010-07-01

Full Text Available Samples of rubber seed shells were carbonized at varying temperatures (100, 200, 300, 400, 500, 600, 700 and 800 °C for three hours each and sieved through a 150 μm screen. The portion of the rubber seed shell carbon that passed through the screen was characterized in terms of loss on ignition, surface area, moisture content, pH, bulk density, and metal content and used in compounding natural rubber. The characterization shows that the pH, conductivity, loss on ignition and the surface area increases with the increases of the heating temperature, unlike the bulk density which decreases. The compound mixes were cured using the efficient vulcanization system. Cure characteristics of compounds and physico-mechanical properties of the vulcanisates were measured as a function of filler loading along with that of N330 carbon-black filled natural rubbers. The results showed that the cure times, scorch times and the torque gradually increased, with increasing the filler content for rubber seed shell carbon-filled natural rubber, with the filler obtained at carbonizing temperature of 600 °C tending to show optimum cure indices. The physicomechanical properties of the vulcanisates increase with filler loading. The reinforcing potential of the carbonized rubber seed shell carbon was found to increase markedly for the filler obtained at the temperature range of 500-600 °C and then decreases with further increase in temperature.

Radiation processed polychloroprene-co-ethylene-propene diene terpolymer blends: Effect of radiation vulcanization on solvent transport kinetics

Energy Technology Data Exchange (ETDEWEB)

Dubey, K.A. [Radiation Technology Development Section, Bhabha Atomic Research Centre, Room No. S-1, HIRUP Building, Trombay, Mumbai 400 085 (India); Bhardwaj, Y.K. [Radiation Technology Development Section, Bhabha Atomic Research Centre, Room No. S-1, HIRUP Building, Trombay, Mumbai 400 085 (India)], E-mail: ykbhard@barc.gov.in; Chaudhari, C.V.; Kumar, Virendra; Goel, N.K.; Sabharwal, S. [Radiation Technology Development Section, Bhabha Atomic Research Centre, Room No. S-1, HIRUP Building, Trombay, Mumbai 400 085 (India)

2009-03-15

Blends of polychloroprene rubber (PCR) and ethylene propylene diene terpolymer rubber (EPDM) of different compositions were made and exposed to different gamma radiation doses. The radiation sensitivity and radiation vulcanization efficiency of blends was estimated by gel-content analysis, Charlesby-Pinner parameter determination and crosslinking density measurements. Gamma radiation induced crosslinking was most efficient for EPDM (p{sub 0}/q{sub 0} {approx} 0.08), whereas it was the lowest for blends containing 40% PCR (p{sub 0}/q{sub 0} {approx} 0.34). The vulcanized blends were characterized for solvent diffusion characteristics by following the swelling dynamics. Blends with higher PCR content showed anomalous swelling. The sorption and permeability of the solvent were not strictly in accordance with each other and the extent of variation in two parameters was found to be a function of blend composition. The {delta}G values for solvent diffusion were in the range -2.97 to -9.58 kJ/mol and indicated thermodynamically favorable sorption for all blends. These results were corroborated by dynamic swelling, experimental as well as simulated profiles and have been explained on the basis of correlation between crosslinking density, diffusion kinetics, thermodynamic parameters and polymer-polymer interaction parameter.

Effect of sulfur and Nano- carbon black on the mechanical properties of hard rubber

Directory of Open Access Journals (Sweden)

Mohamed Hamza Al-Maamori

2018-01-01

Full Text Available To improve the properties of hard rubber(Ebonite from natural rubber, added Nano-Carbon black, where measured the properties of tensile, density, hardness and the properties of the vulcanization of a group of samples with different amount of sulfur from 18-36 pphr and different of carbon black (18-26-30 pphr. The results showed that the best carbon black ratio is 30 pphr, where it gives a balance between tensile properties of hand and toughness and flexibility of on the other hand and reduce brittleness in hard rubber.

Modification of the properties of NBR/EPDM blends vulcanized by gamma irradiation

International Nuclear Information System (INIS)

Abou Zeid, M.M.; Shaltout, N.A.; Mohamed, M.A.; El Miligy, A.A.

2001-01-01

Blends of nitrile-butadiene rubber, NBR with ethylene propylene diene monomer EPDM rubber with varying contents have been prepared. Unloaded or loaded blends with 40 phr of HAF carbon black have been vulcanized by using gamma irradiation. Mechanical properties, namely tensile strength, tensile modulus and elongation at break have been followed up as a function of irradiation dose as well as blend component compositions. Moreover, the susceptibility of prepared composites towards organic solvents and car oils has been followed up in terms of swelling number and soluble fraction measurements. The organic solvents used are toluene and dimethyl-formamide and oil are car lubricating and brake oils. The results indicated improvements in mechanical properties of blend composites with irradiation dose and increased content NBR in the blend. Also, susceptibility to fluids decreased appreciably with irradiation dose but with different extents for different fluids

Latex allergy in the workplace.

Science.gov (United States)

Toraason, M; Sussman, G; Biagini, R; Meade, J; Beezhold, D; Germolec, D

2000-11-01

While less than 1% of the general population is sensitized to latex, the U.S. Occupational Safety and Health Administration estimates that 8-12% of health-care workers are sensitized. The major source of workplace exposure is powdered natural rubber latex (NRL) gloves. NRL is harvested from HEVEA: brasiliensis trees and ammoniated to prevent coagulation resulting in the hydrolysis of the latex proteins. Prior to use in manufacturing, the latex is formulated by the addition of multiple chemicals. Thus, human exposure is to a mixture of residual chemicals and hydrolyzed latex peptides. Clinical manifestations include irritant contact dermatitis, allergic contact dermatitis (type IV), and type I immediate hypersensitivity response. Type I (IgE-mediated) NRL allergy includes contact urticaria, systemic urticaria, angioedema, rhinitis, conjunctivitis, bronchospasm, and anaphylaxis. Taking an accurate history, including questions on atopic status, food allergy, and possible reactions to latex devices makes diagnosis of type-I latex allergy possible. To confirm a diagnosis, either in vivo skin prick testing (SPT) or in vitro assays for latex-specific IgE are performed. While the SPT is regarded as a primary confirmatory test for IgE-mediated disease, the absence of a U.S. Food and Drug Administration-licensed HEVEA: brasiliensis latex extract has restricted its use in diagnosis. Serological tests have, therefore, become critically important as alternative diagnostic tests. Three manufacturers currently have FDA clearance for in vitro tests, to detect NRL-specific IgE. The commercially available assays may disagree on the antibody status of an individual serum, which may be due to the assay's detecting anti-NRL IgEs to different allergenic NRL proteins. Sensitized individuals produce specific IgE antibody to at least 10 potent HEVEA: allergens, Hev b 1-Hev b 10, each of which differs in its structure, size, and net charge. The relative content and ratios of Hevs in the

Characteristics of styrene-butadiene rubber/silica/Nanoprene compounds for application in tire tread.

Science.gov (United States)

Seo, Byeongho; Kang, Jonghyub; Jang, Sukhee; Kang, Yonggu; Kim, Wonho

2013-03-01

Nanoprene is made from chemically cross-linked rubber particles, and has many hydroxyl groups on the surface of the particles. It is speculated that the Nanoprene could reduce the silica-silica network formation by introducing hydrogen bonding between the silanol group of silica and the hydroxyl group of Nanoprene. In this study, the styrene-butadiene rubber (SBR)/silica compounds with two types of the Nanoprene (BM75OH, BM15OH) were evaluated and it could be well explained by the concept of the volume fraction of filler or the volume fraction of rubber. If the Nanoprene applied to the compound is considered as a kind of filler, the minimum torque values and bound rubber contents of the un-vulcanized compounds, the swelling ratio and the stress-strain relationship of the vulcanized compounds could be well explained by the volume fraction of filler (phi(F)). If Nanoprene is considered as a kind of rubber such as SBR, the properties such as peak tan delta, Payne effect, tan delta at 0 degrees C and 60 degrees C, and abrasion resistance could be well explained by the volume fraction of rubber (phi'(R)). However, the improvement of silica dispersion by addition of the Nanoprene particles in the compounds was not significant. The application of BM75OH as a polymer to the tread compound will be suitable for winter tires. In addition, the compound with BM15OH as an additive will be suitable as a tread compound for summer tires.

3D silicone rubber interfaces for individually tailored implants.

Science.gov (United States)

Stieghorst, Jan; Bondarenkova, Alexandra; Burblies, Niklas; Behrens, Peter; Doll, Theodor

2015-01-01

For the fabrication of customized silicone rubber based implants, e.g. cochlear implants or electrocortical grid arrays, it is required to develop high speed curing systems, which vulcanize the silicone rubber before it runs due to a heating related viscosity drop. Therefore, we present an infrared radiation based cross-linking approach for the 3D-printing of silicone rubber bulk and carbon nanotube based silicone rubber electrode materials. Composite materials were cured in less than 120 s and material interfaces were evaluated with scanning electron microscopy. Furthermore, curing related changes in the mechanical and cell-biological behaviour were investigated with tensile and WST-1 cell biocompatibility tests. The infrared absorption properties of the silicone rubber materials were analysed with fourier transform infrared spectroscopy in transmission and attenuated total reflection mode. The heat flux was calculated by using the FTIR data, emissivity data from the infrared source manufacturer and the geometrical view factor of the system.

The patatin-like protein from the latex of Hevea brasiliensis (Hev b 7) is not a vacuolar protein

NARCIS (Netherlands)

Jekel, PA; Hofsteenge, J; Beintema, JJ

Upon centrifugation, rubber latex is divided into a layer of rubber particles, the cytosol, and the lutoid-body fraction, which is of vacuolar origin. One of the proteins isolated from the lutoid-body fraction is a protein with a molecular mass of 43 kDa, which has esterase activity on

Additive free thermoplastic vulcanizates based on natural rubber

Energy Technology Data Exchange (ETDEWEB)

Mondal, Manas, E-mail: mondal@ipfdd.de [Leibniz-Institut für Polymerforschung Dresden e.V., Institut für Polymerwerkstoffe, Hohe Straße 6, 01069 Dresden (Germany); Technische Universität Dresden, Institut für Werkstoffwissenschaft, 01069 Dresden (Germany); Gohs, Uwe, E-mail: gohs@ipfdd.de [Leibniz-Institut für Polymerforschung Dresden e.V., Institut für Polymerwerkstoffe, Hohe Straße 6, 01069 Dresden (Germany); Wagenknecht, Udo [Leibniz-Institut für Polymerforschung Dresden e.V., Institut für Polymerwerkstoffe, Hohe Straße 6, 01069 Dresden (Germany); Heinrich, Gert [Leibniz-Institut für Polymerforschung Dresden e.V., Institut für Polymerwerkstoffe, Hohe Straße 6, 01069 Dresden (Germany); Technische Universität Dresden, Institut für Werkstoffwissenschaft, 01069 Dresden (Germany)

2013-12-16

Electron induced reactive processing (EIReP) is an eco-friendly and sustainable reactive processing method based on the use of high energy electrons. It was used to cross-link the elastomeric domain phase during melt mixing in order to prepare natural rubber (NR) and polypropylene (PP) based thermoplastic vulcanizates (TPVs). The electron treatment with various values of absorbed dose showed a prominent effect on mechanical, rheological, and morphological characteristics of the PP/NR TPVs. SEM and TEM studies confirmed that these TPVs can exists across the co-continuous or discrete phase morphology. The maximum set of mechanical properties (tensile strength of 15 MPa and elongation at break of more than 500%) were obtained at an absorbed dose of 100 kGy for a 50/50 blend ratio of NR and PP without addition of any compatibilizer or chemicals. At higher values of absorbed dose the degradation of polypropylene showed a negative impact on the properties of the TPVs. Depending on the morphology and the evaluation of mechanical properties a structure–property co-relationship is drawn on the basis of common phenomenological understanding of the TPVs. - Highlights: • Dynamic vulcanization of 50:50 PP/NR blend by high energy electron beam. • PP/NR TPVs show rubber like behavior with melt processability. • High tensile strength of 15 MPa and large extensibility beyond 500%. • Complete phase inversed morphology from NR to PP matrix. • Vulcanized natural rubber particle size of 1–3 μm.

Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives

Directory of Open Access Journals (Sweden)

Dongwei Shao

2016-06-01

Full Text Available Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs, this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%–50% at rotor rotational speeds of 15–45 rpm and filled coefficients of 0.55–0.75. Four regression equations, i.e., the tensile strength (Ts, elongation at break (Eb, hardness (Ha and rebound resilience (Rr as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the Ts, Eb and Rr of the panels were reduced, Ha was considerably increased by 17%–58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%–3%, which was much lower than commercial wood-based composites.

Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives.

Science.gov (United States)

Shao, Dongwei; Xu, Min; Cai, Liping; Shi, Sheldon Q

2016-06-14

Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs), this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%-50% at rotor rotational speeds of 15-45 rpm and filled coefficients of 0.55-0.75. Four regression equations, i.e. , the tensile strength ( T s), elongation at break ( E b), hardness ( H a) and rebound resilience ( R r) as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the T s, E b and R r of the panels were reduced, H a was considerably increased by 17%-58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%-3%, which was much lower than commercial wood-based composites.

Vulcanization Kinetics and Mechanical Properties of Ethylene Propylene Diene Monomer Thermal Insulation

Directory of Open Access Journals (Sweden)

Mohamad Irfan Fathurrohman

2015-07-01

Full Text Available The vulcanization kinetics of Ethylene-propylene diene monomer (EPDM rubber thermal insulation was studied by using rheometer under isothermal condition at different temperatures. The rheometry analysis was used to determining the cure kinetic parameters and predicting the cure time of EPDM thermal insulation. The experimental results revealed that the curing curves of EPDM thermal insulation were marching and the optimum curing time decreased with increasing the temperature. The kinetic parameters were determined from the autocatalytic model showed close fitting with the experimental results, indicating suitability of autocatalytic model in characterizing the cure kinetics. The activation energy was determined from the autocatalytic model is 46.3661 kJ mol-1. The cure time were predicted from autocatalytic model and the obtained kinetic parameter by using the relationship among degree of conversion, cure temperature, and cure time. The predictions of cure time provide information for the actual curing characteristic of EPDM thermal insulation. The mechanical properties of EPDM thermal insulation with different vulcanization temperatures showed the same hardness, tensile strength and modulus at 300%, except at temperature 70 °C, while the elongation at breaking point decreased with increasing temperature of vulcanization. © 2015 BCREC UNDIP. All rights reservedReceived: 8th April 2014; Revised: 7th January 2015; Accepted: 16th January 2015How to Cite: Fathurrohman, M.I., Maspanger, D.R., Sutrisno, S. (2015. Vulcanization Kinetics and Mechanical Properties of Ethylene Propylene Diene Monomer Thermal Insulation. Bulletin of Chemi-cal Reaction Engineering & Catalysis, 10 (2, 104-110. (doi:10.9767/bcrec.10.2.6682.104-110Permalink/DOI: http://dx.doi.org/10.9767/bcrec.10.2.6682.104-110 

Application of gamma irradiation for incorporation of rubber powder in the formulations EPDM and NBR rubber

International Nuclear Information System (INIS)

Kiyan, Ludmila de Ysasa Pozzo

2014-01-01

The natural decomposition of rubber is a very slow process due to its three-dimensional network formed by vulcanized crosslinked structures becoming extremely difficult to reprocess this material. The present work aims to study the application of gamma irradiation as devulcanization process for material reuse/recycling. The interactions of elastomers with ionizing radiation of a gamma source were investigated and the changes in physicochemical properties of the materials were evaluated. Formulations of NBR (acrylonitrile - butadiene) and EPDM (ethylene - propylene - diene terpolymer) from the rubber industry were crosslinked by conventional sulfur-based mixing. Master - batch was processed with rubber powder (industrial waste) and virgin rubber. The raw material (master batch) was irradiated in 60 Co source at doses of 50, 100, 150 kGy and dose rate of 5 kGy h -1 at room temperature. The irradiated material was incorporated in classical sulfur-based formulations. The formulations were characterized by: infrared spectroscopy (FTIR), thermal analysis (TG and DTG), tensile strength, elongation at break, hardness, abrasion resistance, rheometry and swelling. The results showed a predominance of chain scission at a dose of 50 kGy for EPDM rubber. For nitrile predominance of chain scission was observed at a dose of 100 kGy. These results show the possibility of the use of gamma radiation for the reuse/recycling of EPDM and nitrile rubbers. (author)

Preliminary study of semi-refined carrageenan (SRC) as secondary gelling agent in natural rubber (NR) latex foam

Science.gov (United States)

Norhazariah, S.; Azura, A. R.; Azahari, B.; Sivakumar, R.

2017-12-01

Semi-refined carrageenan (SRC) product is considerably cheaper and easier to produce as a natural polysaccharide, which was utilized in food and other product application. However, the application in latex is limited. The aim of this work is to evaluate the SRC produced from low industrial grade seaweed (LIGS) in the latex foam application. The FTIR spectra showed the SRC produced as kappa type carrageenan with lower sulfur content compared to native LIGS. NR latex foam is produced by using the Dunlop method with some modifications. The effect of SRC loading as a secondary gelling agent in NR latex foam is investigated. The density and morphology of the NR latex foam with the addition of the SRC are analyzed. NR latex foam density increased with SRC loading and peaked at 1.8 phr SRC. The addition of SRC has induced the bigger cell size compared to the cell size of the control NR latex foam, as shown in the optical micrograph. It can be concluded that SRC LIGS could be acted as secondary gelling agent in NR latex foam.

Enhancing mechanical and thermal properties of styrene-butadiene rubber/carboxylated acrylonitrile butadiene rubber blend by the usage of graphene oxide with diverse oxidation degrees

Science.gov (United States)

Xue, Xiaodong; Yin, Qing; Jia, Hongbing; Zhang, Xuming; Wen, Yanwei; Ji, Qingmin; Xu, Zhaodong

2017-11-01

Graphene oxide (GO) with various oxidation degrees were prepared through a modified Hummer's method by varying the dosage of oxidizing agent. Styrene-butadiene rubber (SBR)/carboxylated acrylonitrile butadiene rubber (XNBR)/GO nanocomposites were fabricated by aqueous-phase mixing of GO colloidal dispersion with SBR latex and a small loading of XNBR latex, followed by co-coagulation. Effects of GO oxidation degree on the morphology, structure, mechanical and thermal properties of nanocomposites were thoroughly investigated. The results showed that the mechanical strength of nanocomposites were enhanced with the increase of oxidation degree of GO. Especially, when the weight ratio of KMnO4 to graphite was 15/5, the tensile strength, tear strength and thermal conductivity of SBR/XNBR/GO filled with 3 phr (parts per hundred rubber) GO increased by 255.3%, 141.5% and 22.8%, respectively, compared to those of neat SBR/XNBR blend. In addition, the thermal stability and the solvent resistance of the nanocomposites were also improved significantly. This work suggested that GO with higher oxidation degree could effectively improve the properties of SBR/XNBR blend.

Degradation of polyisoprene rubber by newly isolated Bacillus sp. AF-666 from soil.

Science.gov (United States)

Shah, A A; Hasan, F; Shah, Z; Mutiullah; Hameed, A

2012-01-01

Various microorganisms were screened for their ability to degrade polyisoprene rubber (natural rubber latex gloves). Strain AF-666, newly isolated from a soil sample, was selected as the best strain having the ability to grow on polyisoprene containing plates. The strain identified as Bacillus sp. AF-666, was found to degrade polyisoprene rubber, both on basal agar plates (latex overlay) as well as in liquid medium. Qualitative analysis of degradation was done through scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy SEM showed changes in surface morphology, like appearance of pits and cracks, and marked difference in transmittance spectra of test and control due to changes in the functional groups, was detected through FTIR. CO2 evolution as a result of rubber degradation, was calculated gravimetrically by Sturm Test. About 4.43 g/1 of CO2 was produced in case of test, whereas, 1.57 g/1 in case of control. The viable number of cells (CFU/ml) was also higher in test than in control. Present study may provide an opportunity for further studies on the applications of biotechnological processes as a tool for rubber waste management.

Application of gamma irradiation for incorporation of rubber powder in the formulations of EPDM and natural rubber; Aplicacao da radiacao gama para incorporacao do po de borracha em formulacoes de borracha natural e EPDM

Energy Technology Data Exchange (ETDEWEB)

Kiyan, Ludmila Y.P.; Parra, Duclerc Fernandes; Lugao, Ademar Benevolo, E-mail: ludmilapozzo@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP/CQMA), Sao Paulo, SP (Brazil). Centro de Quimica e Meio Ambiente

2013-07-01

The objective of this work was to study the behavior of the recycling of rubber burrs in form of powder, of the rubber industry from EPDM rubber powder and natural rubber with SBR. The rubber powder was irradiated and reused in rubber artifacts formulations for classical vulcanization. The processed material was irradiated using a {sup 60}Co source in doses of 50, 100, 150 and 200 kGy and a dose rate of 5 kGy s-1 at room temperature. The radiation created devulcanization active sites for subsequent integration of the material (rubber powder) in formulations of commercial use. The processes were compared and their products characterized by analytical methods of the physical properties such as strength and elongation. Satisfactory results were found, noting a major spin-off of EPDM chain demonstrated by increased elongation.

Whole-transcriptome survey of the putative ATP-binding cassette (ABC) transporter family genes in the latex-producing laticifers of Hevea brasiliensis.

Science.gov (United States)

Zhiyi, Nie; Guijuan, Kang; Yu, Li; Longjun, Dai; Rizhong, Zeng

2015-01-01

The ATP-binding cassette (ABC) proteins or transporters constitute a large protein family in plants and are involved in many different cellular functions and processes, including solute transportation, channel regulation and molecular switches, etc. Through transcriptome sequencing, a transcriptome-wide survey and expression analysis of the ABC protein genes were carried out using the laticiferous latex from Hevea brasiliensis (rubber tree). A total of 46 putative ABC family proteins were identified in the H. brasiliensis latex. These consisted of 12 'full-size', 21 'half-size' and 13 other putative ABC proteins, and all of them showed strong conservation with their Arabidopsis thaliana counterparts. This study indicated that all eight plant ABC protein paralog subfamilies were identified in the H. brasiliensis latex, of which ABCB, ABCG and ABCI were the most abundant. Real-time quantitative reverse transcription-polymerase chain reaction assays demonstrated that gene expression of several latex ABC proteins was regulated by ethylene, jasmonic acid or bark tapping (a wound stress) stimulation, and that HbABCB15, HbABCB19, HbABCD1 and HbABCG21 responded most significantly of all to the abiotic stresses. The identification and expression analysis of the latex ABC family proteins could facilitate further investigation into their physiological involvement in latex metabolism and rubber biosynthesis by H. brasiliensis.

Effect of phenol formaldehyde resin as vulcanizing agent on flow behavior of HDPE/PB blend

Directory of Open Access Journals (Sweden)

Moayad N. Khalaf

2014-07-01

Full Text Available Thermoplastic elastomer (TPE based on High density polyethylene (HDPE/polybutadiene (HDPE/PB = 70/30 parts blends containing 1, 3, 5, 7 and 10 wt.% of dimethylol phenolic resin as a vulcanizing agent in the presence of SnCl2 as catalyst was prepared. The dimethylol phenolic resin was prepared in our laboratory. The blends were compounded in mixer-60 attached to a Haake rheochord meter-90. The rheological properties were measured at temperatures 140, 160, 180 and 200 °C. The linearity of the flow curve appeared for 5% of the vulcanizing agent. The shear stress and shear viscosity have increased upon increasing the shear rate over a range of loading levels of vulcanizing agent of 1%, 3%, 5%, 7% and 10%. This may be attributed to the increased vulcanization between polyethylene and the rubber blend. The flow behavior index of the system shows a pseudo plastic nature behavior (since n < 1. The consistency index (K increased with the increase in the phenol formaldehyde resin content and the temperature. Hence, the increase in the value of the consistency index (K of the polymer melts refers to more viscous materials prepared. The activation energy for the TPE blends fluctuated indicating that there is phase separation; where each polymer behaved separately. This study showed that HDPE/PB blends are characterized with good rheological properties, which can be recommended to be processed with the injection molding technique.

THE EFFLUENT OF NATURAL-RUBBER FACTORIES IS ENRICHED IN THE ANTIFUNGAL PROTEIN HEVEIN

NARCIS (Netherlands)

SOEDJANAATMADJA, UMS; SUBROTO, T; BEINTEMA, JJ

1995-01-01

Hevein is a small cystine-rich protein with a polypeptide chain length of 43 residues. It occurs in the lutoid body fraction of rubber latex, has affinity for chitin, and inhibits fungal growth. It was isolated from the effluent of a rubber factory in a yield of about 0.7 g/l. The elution position

Silicone rubber curing by high intensity infrared radiation

International Nuclear Information System (INIS)

Huang, T.; Tsai, J.; Cherng, C.; Chen, J.

1994-01-01

A high-intensity (12 kW) and compact (80 cm) infrared heating oven for fast curing (12 seconds) of tube-like silicone rubber curing studies is reported. Quality inspection by DSC and DMA and results from pilot-scale curing oven all suggest that infrared heating provides a better way of vulcanization regarding to curing time, quality, cost, and spacing over conventional hot air heating. copyright 1995 American Institute of Physics

PROBLEMATIC IN THE PROCESSES OF PRODUCTION IN RUBBER PLANTATIONS (Hevea brasiliensis Muell Arg. IN TABASCO, MEXICO

Directory of Open Access Journals (Sweden)

Heyra Izquierdo-Bautista

2011-03-01

Full Text Available The objective of this study was to identify some of the basic problems presented in the production process in rubber plantations Hevea brasiliensis Muell Arg. in Tabasco, Mexico. The applied diagnosis technique was the randomized survey for 68 producers in plantations under rubber production. ANOVA and Duncan analyses were done (P< 0.05. Plantations under production were between 7 to 46 years old. The 24% of these are considered as young plantations (7 to 18 years old, 34% mature (19 to 30 years old, and 12% old growth (31 to 46 years old, according to the level of latex production. Latex collection is realized by 85% men and 15% women. An important detected problem is the incidence of insects and diseases over the 82% of the plantations. In Tabasco State, two types of raw material are generated: clot (solid and latex (liquid. The tapping systems are ½ S d/1 6d/7 (one cuts in an average spiral with daily tapping over the 49% of the plantations, and the system ½ S d/2 6d/7, cuts in semi-spirals with alternating tapping over 51% of the plantations. The producers that practiced daily tapped obtained yields of 1.588 kg per ha/yr of dry rubber, in the other hand, those that tapped every other day obtained a yield of 1.647 kg per ha/year of dry rubber. The yield in daily tapping was 3.54% lower than the system with alternating tapping. The income obtained by the producers of fresh rubber varied from $8.750, 00 (810, 2 USD ha/year to $27.870, 00 (2.580 USD ha/year in 2006 and the production of latex from $5.955, 00 (551, 4 USD to 16.568,00 (1.534 USD per ha/year.

Evaluation of sodium diclofenac release using natural rubber latex as carrier

International Nuclear Information System (INIS)

Aielo, Patricia B.; Borges, Felipe A.; Romeira, Karoline M.; Herculano, Rondinelli D.; Miranda, Matheus Carlos Romeiro; Arruda, Larisa B. de; Lisboa Filho, Paulo Noronha; Drago, Bruno de C.

2014-01-01

Sodium Diclofenac is a non-steroidal anti-inflammatory drug (NSAID) taken to reduce inflammation and, as an analgesic, reduce pain. Although this drug is widely used in the general population, properties such as the short half-time and some side effects restrict its clinical use. The most common side effects are: gastric irritation, gastritis, peptic ulcer and bleeding. Studies involving biomaterials as carrier for drug release have been proving their efficiency in overcoming those problems and better controlling the release rate and targeting of the drug. Natural rubber latex (NRL) has been proven excellent for its biocompatibility and ability to stimulate angiogenesis, cellular adhesion and the formation of extracellular matrix, promoting the replacement and regeneration of tissue. In this work, a NRL membrane is used to deliver sodium diclofenac. Sodium diclofenac (NaDic) was found to be adsorbed on the NRL membrane, with little or no incorporation into the membrane bulk, according to energy dispersive Scanning Electron Microscopy with X-Ray microanalysis (SEM-EDS) spectroscopy. In addition, FT-IR shows that there is no molecular-level interaction between drug and NRL. Already, the X-Ray Diffraction (XRD) of NaDic-NRL shows a broader one spectrum than the sharper halo (amorphous characteristic XRD spectrum) of pure NRL. More importantly, the release time of diclofenac in a NRL membrane in vitro was increased from the typical 2-3 h for oral tablets to ca. 74 h. The kinetics of the drug release could be fitted with a double exponential function, with two characteristic times of 0.899 and 32.102 h. In this study, we demonstrated that the interesting properties provided by NRL membranes combined with a controlled release of drug is relevant for biomedical applications.(author)

Evaluation of sodium diclofenac release using natural rubber latex as carrier

Energy Technology Data Exchange (ETDEWEB)

Aielo, Patricia B.; Borges, Felipe A.; Romeira, Karoline M.; Herculano, Rondinelli D., E-mail: rond@assis.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Assis, SP (Brazil). Fac. de Ciencias e Letras. Dept. de Ciencias Biologicas; Miranda, Matheus Carlos Romeiro [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Araraquara, SP (Brazil). Inst. de Quimica; Arruda, Larisa B. de; Lisboa Filho, Paulo Noronha; Drago, Bruno de C. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Bauru, SP (Brazil). Fac. de Ciencias. Dept. de Fisica

2014-08-15

Sodium Diclofenac is a non-steroidal anti-inflammatory drug (NSAID) taken to reduce inflammation and, as an analgesic, reduce pain. Although this drug is widely used in the general population, properties such as the short half-time and some side effects restrict its clinical use. The most common side effects are: gastric irritation, gastritis, peptic ulcer and bleeding. Studies involving biomaterials as carrier for drug release have been proving their efficiency in overcoming those problems and better controlling the release rate and targeting of the drug. Natural rubber latex (NRL) has been proven excellent for its biocompatibility and ability to stimulate angiogenesis, cellular adhesion and the formation of extracellular matrix, promoting the replacement and regeneration of tissue. In this work, a NRL membrane is used to deliver sodium diclofenac. Sodium diclofenac (NaDic) was found to be adsorbed on the NRL membrane, with little or no incorporation into the membrane bulk, according to energy dispersive Scanning Electron Microscopy with X-Ray microanalysis (SEM-EDS) spectroscopy. In addition, FT-IR shows that there is no molecular-level interaction between drug and NRL. Already, the X-Ray Diffraction (XRD) of NaDic-NRL shows a broader one spectrum than the sharper halo (amorphous characteristic XRD spectrum) of pure NRL. More importantly, the release time of diclofenac in a NRL membrane in vitro was increased from the typical 2-3 h for oral tablets to ca. 74 h. The kinetics of the drug release could be fitted with a double exponential function, with two characteristic times of 0.899 and 32.102 h. In this study, we demonstrated that the interesting properties provided by NRL membranes combined with a controlled release of drug is relevant for biomedical applications.(author)

Novel Polyvinyl Alcohol/Styrene Butadiene Rubber Latex/Carboxymethyl Cellulose Nanocomposites Reinforced with Modified Halloysite Nanotubes

Directory of Open Access Journals (Sweden)

Yanjun Tang

2013-01-01

Full Text Available Novel polyvinyl alcohol (PVA/styrene butadiene rubber (SBR latex/carboxymethyl cellulose (CMC/halloysite nanotubes (HNTs nanocomposites were successfully prepared through physical blending. The as-obtained PVA/SBR/CMC/HNTs nanocomposites were coated on the surface of old corrugated container (OCC-based paper in an effort to improve the mechanical properties of paper. To improve the dispersion of HNTs and enhance the compatibility between HNTs and polymer matrix, HNTs were modified with titanate coupling agent (TCA. FT-IR, together with TGA, confirmed that TCA was grafted onto the surface of HNTs successfully. XRD demonstrated that the crystal structures of HNTs remained almost unchanged. TEM showed that modified HNTs exhibited good dispersion and possessed nanotubular structures with an outer diameter of around 50 nm and an inner diameter of about 20 nm. SEM gave an indication that modified HNTs were dispersed more uniformly than unmodified HNTs within PVA/SBR/CMC matrix. Rheological measurement exhibited that surface modification process enhanced the compatibility between HNTs and polymer matrix, thus resulting in the decreased viscosity of nanocomposites. In comparison with unmodified HNTs, modified HNTs were found to contribute more to the enhancement in mechanical properties, which might be attributed to the better dispersion and compatibility of modified HNTs evidenced by TEM, SEM, and rheological measurement.

Preparation and characterization of zinc sulphide nanocomposites based on acrylonitrile butadiene rubber

Science.gov (United States)

Ramesan, M. T.; Nihmath, A.; Francis, Joseph

2013-06-01

Rubber composite based on acrylonitrile butadiene rubber (NBR) reinforced with nano zinc sulphide (ZnS) have been prepared via vulcanization process and characterized by several techniques. Processing characteristics such as scorch time, optimum cure time decreases with increase in concentration of nano filler in acrylonitrile butadiene rubber. Mechanical properties such as tensile and tear strength increases with increase in concentration of nano filler up to 7 phr of loading thereafter the value decreases, whereas hardness, and flame resistance increases with the dosage of fillers. These enhanced properties are due to the homogenous dispersion of nano fillers in NBR matrix, which is evidenced from the structure that evaluated using X-ray diffraction (XRD) and scanning electron microscopy (SEM).

Recycling of scrap tyres

International Nuclear Information System (INIS)

Jana, G.K.; Das, C.K.

2005-01-01

De-vulcanization of rubber waste posses a challenging economical, environmental and social problem. In the present study, we propose a new de vulcanization process to reuse the rubber waste called mechan-chemical process (MCP), where the waste were de-vulcanized through the application of mechanical shearing, heat (110 degree C) and de-vulcanizing agent (Di-benzyl disulfide). A new look into the de-vulcanization mechanism and the influence of de-vulcanizing agent on mechanical properties of re-vulcanized rubber was presented. One of the most interesting observations is that the retention of tensile strength of re-vulcanized rubber with respect to original tyre is 35.1% and 75.6%, when de-vulcanized in absence and in presence of disulfide respectively. The formation of extra cross-link bond in re-vulcanized rubber containing disulfide was confirmed from cross-link density data and TGA result. DMA analysis revealed that the storage modulus increased for re vulcanized rubber containing disulfide. The SEM was considered in order to study the failure mechanism and homogeneity as affected by the de vulcanization process

Radiation pre-vulcanization effect on properties of the truck tyre's transition layer and the truck tyre

International Nuclear Information System (INIS)

Yang Mingcheng; Zhu Jun; Li Kunhao; Guo Dongquan; Zhang Hongna; Zhang Benshang; Li Zhaopeng

2013-01-01

In this paper, the natural rubber is chosen as the main constituents for the transition layer of all-steel load radial tyre, which is pre-vulcanized by 500-keV E-beam irradiation of up to 60 kGy. The results show that the green strength of transitional layer increases with the dose, reaching four times as much as the control (without irradiation) at 60 kGy. The final mechanical properties do not differ significantly from those of the control except that the aging and fatigue performance increased. However, thickness of the natural rubber transitional layer for an average single tyre can be reduced by 1 mm (or 1.5 kg) without obvious adverse effect on tyre performance. (authors)

Penelitian “rubber blend” antara karet alam rss dengan karet sintesis jsr 0061 untuk sol ringan sesuai sni 12-0778-1989

Directory of Open Access Journals (Sweden)

Penny Setyowati

1997-12-01

Full Text Available The objective of this research is to find composision of rubber blend of RSS and JSR 0061 and Carbon black for preparation light rubber sole compound and stabile on high process temperature that give the best fisical properties and the best sole product at moulding vulcanization trial. The best rubber compound to be reached at the compound formulation R III with composision of RSS 90 phr, JSR 0061 10 phr dan carbon black 40 phr.

Crystallization of Hevamine, an Enzyme with Lysozyme/Chitinase Activity from Hevea brasiliensis Latex

NARCIS (Netherlands)

ROZEBOOM, HJ; BUDIANI, A; BEINTEMA, JJ

1990-01-01

Hevamine, an enzyme with both lysozyme and chitinase activity, was isolated and purified from Hevea brasiliensis (rubber tree) latex. The enzyme (molecular weight 29,000) is homologous to certain “pathogenesis-related” proteins from plants, but not to hen egg-white or phage T4 lysozyme. To

Involvement of Ethylene in the Latex Metabolism and Tapping Panel Dryness of Hevea brasiliensis

Science.gov (United States)

Putranto, Riza-Arief; Herlinawati, Eva; Rio, Maryannick; Leclercq, Julie; Piyatrakul, Piyanuch; Gohet, Eric; Sanier, Christine; Oktavia, Fetrina; Pirrello, Julien; Kuswanhadi; Montoro, Pascal

2015-01-01

Ethephon, an ethylene releaser, is used to stimulate latex production in Hevea brasiliensis. Ethylene induces many functions in latex cells including the production of reactive oxygen species (ROS). The accumulation of ROS is responsible for the coagulation of rubber particles in latex cells, resulting in the partial or complete stoppage of latex flow. This study set out to assess biochemical and histological changes as well as changes in gene expression in latex and phloem tissues from trees grown under various harvesting systems. The Tapping Panel Dryness (TPD) susceptibility of Hevea clones was found to be related to some biochemical parameters, such as low sucrose and high inorganic phosphorus contents. A high tapping frequency and ethephon stimulation induced early TPD occurrence in a high latex metabolism clone and late occurrence in a low latex metabolism clone. TPD-affected trees had smaller number of laticifer vessels compared to healthy trees, suggesting a modification of cambial activity. The differential transcript abundance was observed for twenty-seven candidate genes related to TPD occurrence in latex and phloem tissues for ROS-scavenging, ethylene biosynthesis and signalling genes. The predicted function for some Ethylene Response Factor genes suggested that these candidate genes should play an important role in regulating susceptibility to TPD. PMID:26247941

The improvement in functional characteristics of eco-friendly composites made of natural rubber and cellulose

Energy Technology Data Exchange (ETDEWEB)

Araki, Kunihiro; Kaneko, Shonosuke; Matsumoto, Koki; Tanaka, Tatsuya; Arao, Yoshihiko [Applied Materials Engineering Laboratory, Faculty of Engineering, Doshisha University, 1-3, Tatara Miyakodani, Kyotanabe, Kyoto, 610-0321 (Japan); Nagatani, Asahiro [Applied Materials Engineering Laboratory, Faculty of Engineering, Doshisha University, 1-3, Tatara Miyakodani, Kyotanabe, Kyoto, 610-0321 (Japan); Hyogo Prefectural Institute of Technology, 3-1-12, Yukihira-cho, Suma-ku, Kobe, Hyogo, 654-0037 (Japan)

2015-05-22

We investigated the efficient use of cellulose to resolve the problem of the depletion of fossil resources. In this study, as the biomass material, the green composite based on natural rubber (NR) and the flake-shaped cellulose particles (FSCP) was produced. In order to further improvement of functional characteristics, epoxidized natural rubber (ENR) was also used instead of NR. The FSCP were produced by mechanical milling in a planetary ball mill with a grinding aid as a cellulose aggregation inhibitor. Moreover, talc and mica particles were used to compare with FSCP. NR and ENR was mixed with vulcanizing agents and then each filler was added to NR compound in an internal mixer. The vulcanizing agents are as follows: stearic acid, zinc oxide, sulfur, and vulcanization accelerator. The functionalities of the composites were evaluated by a vibration-damping experiment and a gas permeability experiment. As a result, we found that FSCP filler has effects similar to (or more than) inorganic filler in vibration-damping and O{sub 2} barrier properties. And then, vibration- damping and O{sub 2} barrier properties of the composite including FSCP was increased with use of ENR. In particular, we found that ENR-50 composite containing 50 phr FSCP has three times as high vibration-damping property as ENR-50 without FSCP.

Novel thermoplastic vulcanizates (TPVs based on silicone rubber and polyamide exploring peroxide cross-linking

Directory of Open Access Journals (Sweden)

K. Naskar

2014-04-01

Full Text Available Novel thermoplastic vulcanizates (TPVs based on silicone rubber (PDMS and polyamide (PA12 have been prepared by dynamic vulcanization process. The effect of dynamic vulcanization and influence of various types of peroxides as cross-linking agents were studied in detail. All the TPVs were prepared at a ratio of 50/50 wt% of silicone rubber and polyamide. Three structurally different peroxides, namely dicumyl peroxide (DCP, 3,3,5,7,7-pentamethyl 1,2,4-trioxepane (PMTO and cumyl hydroperoxide (CHP were taken for investigation. Though DCP was the best option for curing the silicone rubber, at high temperature it suffers from scorch safety. An inhibitor 2,2,6,6-tetramethylpiperidinyloxyl (TEMPO was added with DCP to stabilize the radicals in order to increase the scorch time. Though CHP (hydroperoxide had higher half life time than DCP at higher temperature, it has no significant effect on cross-linking of silicone rubber. PMTO showed prolonged scorch safety and better cross-linking efficiency rather than the other two. TPVs of DCP and PMTO were made up to 11 minutes of mixing. Increased values of tensile strength and elongation at break of PMTO cross-linked TPV indicate the superiority of PMTO. Scanning electron micrographs correlate with mechanical properties of the TPVs. High storage modulus (E' and lower loss tangent value of the PMTO cross-linked TPV indicate the higher degree of cross-linking which is also well supported by the overall cross-link density value. Thus PMTO was found to be the superior peroxide for cross-linking of silicone rubber at high temperature.

Study on determination of durability analysis process and fatigue damage parameter for rubber component

International Nuclear Information System (INIS)

Moon, Seong In; Cho, Il Je; Woo, Chang Su; Kim, Wan Doo

2011-01-01

Rubber components, which have been widely used in the automotive industry as anti-vibration components for many years, are subjected to fluctuating loads, often failing due to the nucleation and growth of defects or cracks. To prevent such failures, it is necessary to understand the fatigue failure mechanism for rubber materials and to evaluate the fatigue life for rubber components. The objective of this study is to develop a durability analysis process for vulcanized rubber components, that can predict fatigue life at the initial product design step. The determination method of nonlinear material constants for FE analysis was proposed. Also, to investigate the applicability of the commonly used damage parameters, fatigue tests and corresponding finite element analyses were carried out and normal and shear strain was proposed as the fatigue damage parameter for rubber components. Fatigue analysis for automotive rubber components was performed and the durability analysis process was reviewed

Enzymatic synthesis of rubber polymer in Hevea brasiliensis

Energy Technology Data Exchange (ETDEWEB)

Tang, F.; Hu, S.; Benedict, C.R. (Texas A and M Univ., College Station (United States))

1991-05-01

Light and Dennis purified serum soluble rubber transferase from Hevea latex to homogeneity. Prenyl transferase co-purified with rubber transferase. In the absence of washed rubber particles (WRP) the prenyl transferase catalyzed the formation of trans FPP from DMAPP and IPP. In the presence of WRP the transferase catalyzed cis additions of IPP to pre-existing rubber chains. Control mixtures of WRP, Mg{sup 2+} and FPP were not included to test for the contributions of the bound rubber transferase on WRP to the incorporation of IPP into polyisoprene. Bound rubber transferase catalyzes the repetitive addition of IPP to allylic-PP starter molecules to form polyisoprene. The order of utilization of allylic-PP starters was GGPP > FPP > GPP > DMAPP. The authors have shown that the polyisoprene enzymatically synthesized on WRP is a bimodal polymer consisting of different mol wt rubber chains similar to the polymeric characteristics of natural rubber. The bound rubber transferase was solubilized with Chaps and purified on DEAE-cellulose. The polymerization reaction catalyzed by the purified preparation showed a 98% requirement for pre-existing rubber chains. Results suggest that the prenyl transferase from Hevea serum may be part of the polymer starter system furnishing allylic-PP for the bound rubber transferase.

Fatigue Performance and Multiscale Mechanisms of Concrete Toughened by Polymers and Waste Rubber

Directory of Open Access Journals (Sweden)

Bo Chen

2014-01-01

Full Text Available For improving bending toughness and fatigue performance of brittle cement-based composites, two types of water-soluble polymers (such as dispersible latex powder and polyvinyl alcohol powder and waste tire-rubber powders are added to concrete as admixtures. Multiscale toughening mechanisms of these additions in concretes were comprehensively investigated. Four-point bending fatigue performance of four series concretes is conducted under a stress level of 0.70. The results show that the effects of dispersible latex powder on bending toughness and fatigue life of concrete are better than those of polyvinyl alcohol powder. Furthermore, the bending fatigue lives of concrete simultaneously containing polymers and waste rubber powders are larger than those of concrete with only one type of admixtures. The multiscale physics-chemical mechanisms show that high bonding effect and high elastic modulus of polymer films as well as good elastic property and crack-resistance of waste tire-rubber powders are beneficial for improving bending toughness and fatigue life of cementitious composites.

Applications of nuclear technology in industry, environment and medicine

International Nuclear Information System (INIS)

Vera Ruiz, H.

1998-01-01

This article contains information on different applications of nuclear technology, such as: sterilization of single use medical products, radiation serialization of pharmaceutical products,radiation treatment of disposable products, in Europe, radiation treatment of micro-titer plates, several crosslinking processes, radiation vulcanization of natural rubber latex, irradiation of polymers to obtain dressings for burns, ulcers bedsores and skin grafts, production of ground water with accelerated electrons in combination with accelerated electrons in combination with ozone, radiation treatment of hospital wastes. (S. Grainger)

[Epidemiology of contact hypersensitivity to rubber components in manufacturers of automobile tires at the Stomil plant].

Science.gov (United States)

Rubisz-Brzezińska, J; Bogdanowski, T; Brzezińska-Wcisło, L; Mozdzanowska, K; Bajcar, S

1990-01-01

Dermatological examination and patch tests with 34 rubber components were carried out in 114 tire manufacturers, 78 women and 36 men aged 29 years on average, with a mean duration of work in the plant 7 years. For correct interpretation of the obtained results patch tests with the same components were done in two control groups that is in 120 healthy subjects and 120 patients with contact dermatitis. Patch tests with proper concentrations of the studied components were evaluated after 48, 72 and 96 hours. Positive patch tests were found most frequently with antioxidants--16.6% (including IPPD--8.6%), followed by vulcanization accelerators--10.6%, and other rubber components--11.4% in all. During about 3 years of follow-up in 4 manufacturers contact allergic eczema was noted and polyvalent hypersensitivity to antioxidants and vulcanization accelerators without clinical manifestations of this hypersensitivity was diagnosed in 3 other subjects.

Microstructure, molecular weight and thermal behavior of natural rubber (NR) from mangabeira (Hancornia speciosa)

International Nuclear Information System (INIS)

Santos, Expedito Flavio dos; Feitosa, Judith P.A.; Ricardo, Nagila M.P.S.

2001-01-01

The natural rubber (NR) from Hancornia speciosa contains characteristics that turns it a good alternative in elastomers supply. The NMR and IR spectra showed that the rubber of mangabeira is composed fundamentally by poly(1,4-cis-isoprene). The rubber molecular weight obtained by GPC and viscometry was 2,0x10 6 and 1,3x10 6 g/mol, respectively, in good agreement with the values determined for seringueira and manicoba NR. The glass transition temperature obtained by DSC (Tg = - 65 deg C) showed the mangabeira rubber is ideal to be utilized in regions of cold climate without compromising its mechanical properties. The rubber has also good thermal stability up to 213 deg C, as indicated by TG curves. This results indicated that the mangabeira NR can be effectively used in vulcanized articles or to be added to asphalt. (author)

Neutron backscattered application in investigation for Pipeline Intelligent Gauge (PIG) tracking in RAYMINTEX matrix pipeline

International Nuclear Information System (INIS)

Mohd Fakarudin Badul Rahman; Ismail Mustapha; Nor Paiza Mohd Hasan; Pairu Ibrahim; Airwan Affandi Mahmood; Mior Ahmad Khusaini Adnan; Najib Mohammed Zakey

2012-01-01

The Radiation Vulcanized Natural Rubber Latex (RVNRL) process plants such RAYMINTEX, pipelines are used extensively to transfer a latex product from storage vessel and being irradiated to produce a high quality of latex. A hydraulically activated Pipeline Intelligent Gauge (PIG) was held back against the latex flow. Consequently, the stuck PIG in pipeline was subjected to interrupt plant operation. The investigation was carried out using the neutron backscattered technique scanner to track the stuck PIG in pipeline of RVNRL plant. The 50 mCi Americium Beryllium (AmBe 241 ) fast neutron emitter source in the range 0.5-11 MeV has been used and thermal neutrons in the 30 eV- 0.5 MeV was detected using Helium-3 (He 3 ) detector. It is observed that there is unambiguous relationship between vapour and RVNRL consequence of diverse hydrogen concentration in pipeline. Thus, neutron backscattered technique was capable to determine the location of stuck PIG in a RVNRL pipeline. (author)

On the response of rubbers at high strain rates.

Energy Technology Data Exchange (ETDEWEB)

Niemczura, Johnathan Greenberg (University of Texas-Austin)

2010-02-01

In this report, we examine the propagation of tensile waves of finite deformation in rubbers through experiments and analysis. Attention is focused on the propagation of one-dimensional dispersive and shock waves in strips of latex and nitrile rubber. Tensile wave propagation experiments were conducted at high strain-rates by holding one end fixed and displacing the other end at a constant velocity. A high-speed video camera was used to monitor the motion and to determine the evolution of strain and particle velocity in the rubber strips. Analysis of the response through the theory of finite waves and quantitative matching between the experimental observations and analytical predictions was used to determine an appropriate instantaneous elastic response for the rubbers. This analysis also yields the tensile shock adiabat for rubber. Dispersive waves as well as shock waves are also observed in free-retraction experiments; these are used to quantify hysteretic effects in rubber.

Outcomes of a natural rubber latex control program in an Ontario teaching hospital.

Science.gov (United States)

Tarlo, S M; Easty, A; Eubanks, K; Parsons, C R; Min, F; Juvet, S; Liss, G M

2001-10-01

Allergy to natural rubber latex (NRL) has been frequently reported in health care workers. However, there is little published evidence of the outcome of hospital intervention programs to reduce exposure and detect cases of sensitization early. This study assesses the effects of intervention to reduce NRL allergy in an Ontario teaching hospital with approximately 8000 employees. A retrospective review assessed annual numbers of employees visiting the occupational health clinic, allergy clinic, or both for manifestations of NRL allergy compared with the timing of introduction of intervention strategies, such as worker education, voluntary medical surveillance, and hospital conversion to low-protein, powder-free NRL gloves. The number of workers identified with NRL allergy rose annually, from 1 in 1988 to 6 in 1993. When worker education and voluntary medical surveillance were introduced in 1994, a further 25 workers were identified. Nonsterile gloves were changed to low-protein, powder-free NRL gloves in 1995: Diagnoses fell to 8 workers that year, and 2 of the 3 nurses who had been off work because of asthma-anaphylaxis were able to return to work with personal avoidance of NRL products. With a change to lower protein, powder-free NRL sterile gloves in 1997, allergy diagnoses fell to 3, and only 1 new case was identified subsequently up to May 1999. No increased glove costs were incurred as a result of consolidated glove purchases. This program to reduce NRL allergy in employees was effectively achieved without additional glove costs while reducing expenses from time off work and workers' compensation claims.

Mechanical Properties of Graphene-Rubber Nanocomposites

Science.gov (United States)

Anhar, N. A. M.; Ramli, M. M.; Hambali, N. A. M. A.; Aziz, A. A.; Mat Isa, S. S.; Danial, N. S.; Abdullah, M. M. A. B.

2017-11-01

This research focused on development of wearable sensor device by using Prevulcanized Natural Rubber (PV) and Epoxidized Natural Rubber (ENR 50) latex incorporated with graphene oxide (GO), graphene paste, graphene powder and reduced graphene oxide (rGO) powder. The compounding formulation and calculation were based on phr (parts per hundred rubber) and all the samples were then tested for mechanical properties using Instron 5565 machine. It was found that the sonication effects on tensile strength may have better quality of tensile strength compared to non-sonicated GO. For PV incorporate GO, the optimum loading was best determined at loading 1.5 phr with or without sonication and similar result was recorded for PV/G. For ENR 50 incorporate graphene paste and rGO powder nanocomposite shows the best optimum was at 3.0 phr with 24 hours’ sonication.

Reinforcing styrene butadiene rubber with lignin-novolac epoxy resin networks

Directory of Open Access Journals (Sweden)

P. Yu

2015-01-01

Full Text Available In this study, lignin-novolac epoxy resin networks were fabricated in the styrene butadiene rubber (SBR matrix by combination of latex compounding and melt mixing. Firstly, SBR/lignin compounds were co-coagulated by SBR latex and lignin aqueous solution. Then the novolac epoxy resin (F51 was added in the SBR/lignin compounds by melt compounding method. F51 was directly cured by lignin via the ring-opening reaction of epoxy groups of F51 and OH groups (or COOH groups of lignin during the curing process of rubber compounds, as was particularly evident from Fourier transform infrared spectroscopy (FTIR studies and maximum torque of the curing analysis. The existence of lignin-F51 networks were also detected by scanning electron microscope (SEM and dynamic mechanical analysis (DMA. The structure of the SBR/lignin/F51 was also characterized by rubber process analyzer (RPA, thermogravimetric analysis (TGA and determination of crosslinking density. Due to rigid lignin-F51 networks achieved in SBR/lignin/F51 composites, it was found that the hardness, modulus, tear strength, crosslinking density, the temperature of 5 and 10% weight-loss were significantly enhanced with the loading of F51.

Effects of moulding and environmental conditions on the mechanical and surface properties of injection moulded santoprene rubber

DEFF Research Database (Denmark)

Islam, Aminul; Ruby, Tobias M.; Jessen, Rikke L.

the electronics inside from environmental hazards. The sealing ring is injection moulded in Santoprene-a thermoplastic vulcanizate consisting of Polypropelene and highly vulcanized EPDM rubber. The scope of the project was therefore to investigate the properties of Santoprene and make an immediate evaluation...

The use of plasticizing additives based on recycled raw materials in the petrochemical rubber mixtures

Directory of Open Access Journals (Sweden)

Z. S. Shashok

2016-01-01

Full Text Available At present, the development of alternative products for elastomers based on recycling petrochemical raw materials is a new trend of the rubber industry progress. Petrochemical raw materials include spent lubricants and motor oils are among such recycling products. In this context, the influence of the products of recycling waste engine oil (DVCH and RA in comparison with industrial oil (I-20 on the technological properties of filled elastomeric compositions was investigated. The elastomeric compositions were based on poly isoprene and divinyl rubbers. The plasticizing components were manufactured by IOOO “DVCH-Menedzhment”. They are mixture of hydro-carbons, C16–C20 and differ from each other in the content of linear and branched paraffin. Plastic-elastic properties of rubber compounds on the shear disk viscometer MV2000 in accordance with GOST 10722–76 was carried out. Kinetics of vulcanization on the rheometer ODR2000 according to GOST 12535–84 was defined. It is shown that the introduction of RA test plasticizing component provides a significant effect on Mooney viscosity, as compared to elastomeric compositions containing a plasticizer and I-20 and plasticizing additive DVCH. It revealed that the administration of all components in the studied plasticizing elastomer compositions based on a combination poly isoprene and divinyl rubbers has no significant effect on the rate of relaxation of stress of rubber compounds. It is found that elastomeric compositions containing as additives investigated processing waste oil products (DVCH and RA are characterized by a slightly smaller value of time to reach an optimal degree of vulcanization.

Characterization of the natural rubber from new rubber tree clones of PB 300 series

International Nuclear Information System (INIS)

Silva, Maycon J.; Spinelli, Rafaela O.; Moreno, Rogerio M.B.; Mattoso, Luiz H.C.; Martins, Maria Alice; Scaloppi Junior, Erivaldo J.

2015-01-01

The natural rubber (NR) is present in more than 2500 species of plants, being the Hevea brasiliensis the most commercially exploited. It is a raw material of great importance to the Brazilian economy, but the country faces a production's deficit, having to import about 60% of its consumption. In this work , the latex obtained from rubber tree of new clones of PB series 300 (PB 311, PB 312, PB 314 , PB 326, PB 346 and PB 350 ) and RRIM 600 (control) were characterized by dry rubber content (DRC), total solids content, distribution of particle size, Zeta potential, thermogravimetry, differential scanning calorimetry, infrared in the spectroscopy (FTIR), nuclear magnetic resonance (NMR) and technological properties. The DRC values ranged from 33% to 40%, and total solids of 38% to 44%. All of the clones showed average particle diameter between 180.0 to 192.1 nm, excluding clones PB 326 and PB 346 with 150.0 nm and 157.9 nm, respectively. The NMR spectra and FTIR showed that the structure of the natural rubber from all clones studied is cis -1,4- polyisoprene. Natural rubber from the new clones showed good thermal stability up to 285 °C and glass transition temperature of -64 °C. (author)

Latex stage blending of multiwalled carbon nanotube in carboxylated acrylonitrile butadiene rubber: Mechanical and electrical properties

International Nuclear Information System (INIS)

Preetha Nair, K.; Thomas, Paulbert; Joseph, Rani

2012-01-01

Highlights: ► MWCNT can act as a reinforcing filler in XNBR at very low concentration. ► SEM and XRD analysis confirm uniform distribution of nanotube in the matrix. ► Mechanical properties showed considerable improvement. ► Thermal stability of the composite is marginally improved. -- Abstract: Multiwalled carbon nanotube (MWCNT) was dispersed in sodium dodecyl benzene sulphonate (SDBS) by sonication. The dispersed MWCNT (0.05–0.3 gm) was incorporated in carboxylated acrylonitrile butadiene rubber (XNBR) latex. Mechanical, electrical and thermal properties of these composites were studied. Mechanical properties of the composites increased up to an optimum concentration and then decreased. Dielectric properties of the composites were studied in the S band (frequency range 2–4 GHz) by Cavity Perturbation method. Direct current (DC) electrical conductivity shows a percolation behaviour and conductivity increased by about 10 orders of magnitude. Thermal studies were conducted using Differential Scanning Calorimetry (DSC) and Thermo Gravimetric Analysis (TGA). As expected with the very small concentration of multiwalled carbon nanotube, glass transition temperature (T g ) and thermal stability of the composite showed a marginal increase. Composites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and Scanning electron microscope (SEM) analysis.

Effect of montmorillonite on carboxylated styrene butadiene rubber/hindered phenol damping material with improved extraction resistance

International Nuclear Information System (INIS)

Gao, Yuan; Wang, Xiaoping; Liu, Meijun; Xi, Xue; Zhang, Xin; Jia, Demin

2014-01-01

Highlights: • MMT and XSBR display synergic effect on protecting HP1098 from being extracted. • A new hindered phenol HP1098 was used to prepare damping material. • Effects of three preparation methods on the material properties were studied. - Abstract: Three methods of blending, including direct blending, melt blending and latex blending, were introduced to disperse sodium based montmorillonite (Na-MMT) and N,N′-hexane-1,6-diylbis{3-(5-di-tert-butyl-4-hydroxyphenyl-propionamide)} (HP1098) into the carboxylated styrene butadiene (XSBR) matrix. Small angle X-ray Diffraction testing indicated that melting Na-MMT with HP1098 enlarged the d-spacing of Na-MMT, which was further enlarged by mechanical blending with XSBR, and this led to homogeneous dispersion of Na-MMT and HP1098, which was indicated by Transmission Electronic Microscopy; latex blending was found most advantageous in dispersing HP1098 which was essential for improved damping performance. Dynamic Mechanical Analysis was utilized to characterize damping properties, and enhanced static mechanical properties were presumably originated from molecule chains being intercalated into the enlarged galleries of Na-MMT by mechanical blending. Formation of hydrogen bonds was observed by Fourier Transformation Infrared Spectrum and was supposed to be responsible for exceptional damping performance at elevated temperature. Extraction measurement of XSBR/Na-MMT/HP1098 composite indicated that XSBR and Na-MMT showed synergic effect in protecting HP1098 molecules from being extracted, which is a promising method in preparing rubber/hindered phenol damping materials with improved extraction resistance, whereby increasing the performance stability and lifespan of the composite materials. Additional advantage of this type of materials is better processability and shortened vulcanization process

Silencing the lettuce homologs of small rubber particle protein does not influence natural rubber biosynthesis in lettuce (Lactuca sativa).

Science.gov (United States)

Chakrabarty, Romit; Qu, Yang; Ro, Dae-Kyun

2015-05-01

Natural rubber, cis-1,4-polyisoprene, is an important raw material in chemical industries, but its biosynthetic mechanism remains elusive. Natural rubber is known to be synthesized in rubber particles suspended in laticifer cells in the Brazilian rubber tree (Hevea brasiliensis). In the rubber tree, rubber elongation factor (REF) and its homolog, small rubber particle protein (SRPP), were found to be the most abundant proteins in rubber particles, and they have been implicated in natural rubber biosynthesis. As lettuce (Lactuca sativa) can synthesize natural rubber, we utilized this annual, transformable plant to examine in planta roles of the lettuce REF/SRPP homologs by RNA interference. Among eight lettuce REF/SRPP homologs identified, transcripts of two genes (LsSRPP4 and LsSRPP8) accounted for more than 90% of total transcripts of REF/SRPP homologs in lettuce latex. LsSRPP4 displays a typical primary protein sequence as other REF/SRPP, while LsSRPP8 is twice as long as LsSRPP4. These two major LsSRPP transcripts were individually and simultaneously silenced by RNA interference, and relative abundance, polymer molecular weight, and polydispersity of natural rubber were analyzed from the LsSRPP4- and LsSRPP8-silenced transgenic lettuce. Despite previous data suggesting the implications of REF/SRPP in natural rubber biosynthesis, qualitative and quantitative alterations of natural rubber could not be observed in transgenic lettuce lines. It is concluded that lettuce REF/SRPP homologs are not critically important proteins in natural rubber biosynthesis in lettuce. Copyright © 2014 Elsevier Ltd. All rights reserved.

RTV Silicone Rubber Degradation Induced by Temperature Cycling

Directory of Open Access Journals (Sweden)

Xishan Wen

2017-07-01

Full Text Available Room temperature vulcanized (RTV silicone rubber is extensively used in power system due to its hydrophobicity and hydrophobicity transfer ability. Temperature has been proven to markedly affect the performance of silicone rubbers. This research investigated the degradation of RTV silicone rubber under temperature cycling treatment. Hydrophobicity and its transfer ability, hardness, functional groups, microscopic appearance, and thermal stability were analyzed using the static contact angle method, a Shore A durometer, Fourier transform infrared spectroscopy (FTIR, scanning electron microscopy (SEM, and thermogravimetry (TG, respectively. Some significant conclusions were drawn. After the temperature was cycled between −25 °C and 70 °C, the hydrophobicity changed modestly, but its transfer ability changed remarkably, which may result from the competition between the formation of more channels for the transfer of low molecular weight (LMW silicone fluid and the reduction of LMW silicone fluid in the bulk. A hardness analysis and FTIR analysis demonstrated that further cross-linking reactions occurred during the treatment. SEM images showed the changes in roughness of the RTV silicone rubber surfaces. TG analysis also demonstrated the degradation of RTV silicone rubber by presenting evidence that the content of organic materials decreased during the temperature cycling treatment.

Physicomechanical properties of nanocomposites based on cellulose nanofibre and natural rubber latex

CSIR Research Space (South Africa)

Abraham, E

2012-11-01

Full Text Available and tensile strength was observed as a result of addition of CNF to the rubber matrix especially at higher CNF loading. DMA showed a change in the storage modulus of the rubber matrix upon addition of CNF which proves the reinforcing effect of CNF in the NR...

Effect of rootstock on the scion of Hevea brasiliensis through metabolic analysis of latex samples by 1H NMR

Directory of Open Access Journals (Sweden)

Eduardo Sanches Pereira do Nascimento

2011-01-01

Full Text Available In this study, the effect of rootstock on grafting through metabolomic analysis of latex (Hevea brasiliensis samples was verified by 1H nuclear magnetic resonance (NMR and multivariate data analysis. Sixteen metabolites present in the latex cytosol were characterized by NMR. PCA analysis showed that the latex samples of the RR and GR groups can be differentiated. The GR group samples present a metabolic profile similar to the RR group samples, while the RG group is in an intermediate position between RR and GG groups. Sucrose and formate contributed greatly to the separation obtained by PCA, presenting a good correlation between the results. 1H NMR was an efficient technique to differentiate latex samples from different types of rootstocks and grafting and in the future could be used to predict rubber production by latex analysis.

Elastomeric Nanocomposite Based on Exfoliated Graphene Oxide and Its Characteristics without Vulcanization

Directory of Open Access Journals (Sweden)

Nasser Abdullah Habib

2017-01-01

Full Text Available Rubber nanocomposites have emerged as one of the advanced materials in recent years. The aim of this work was to homogeneously disperse graphene oxide (GO sheets into Nitrile Butadiene Rubber (NBR and investigate the characteristics of GO/NBR nanocomposite without vulcanization. A suitable solvent was found to dissolve dry NBR while GO was exfoliated completely in an aqueous base solution using sonication. GO was dispersed into NBR at different loadings by solution mixing to produce unvulcanized GO/NBR nanocomposites. Scanning Electron Microscopy (SEM, Fourier-Transform Infrared Spectroscopy (FTIR, and X-Ray Diffraction (XRD were used to characterize the samples. Furthermore, mechanical and electrical properties of unvulcanized GO/NBR nanocomposites were carried out to determine the influence of GO on the NBR properties. The results showed that the modulus of GO/NBR nanocomposite at 1 wt% of GO was enhanced by about 238% compared with unfilled NBR. These results provide insight into the properties of unvulcanized GO/NBR nanocomposite for application as coatings or adhesives.

The role of oxide structure on copper wire to the rubber adhesion

Science.gov (United States)

Su, Yea-Yang; Shemenski, Robert M.

2000-07-01

Most metals have an oxide layer on the surface. However, the structure of the oxide varies with the matrix composition, and depends upon the environmental conditions. A bronze coating, nominal composition of 98.5% Cu and balance of Sn, is applied to steel wire for reinforcing pneumatic tire beads and to provide adhesion to rubber. This work studied the influence of copper oxides on the bronze coating on adhesion during vulcanization. To emphasize the oxide structures, electrolytic tough pitch (ETP) copper wire was used instead of the traditional bronze-coated tire bead wire. Experimental results confirmed the hypothesis that cuprous oxide (Cu 2O) could significantly improve bonding between copper wire and rubber, and demonstrated that the interaction between rubber and oxide layer on wire is an electrochemical reaction.

Radiation pre-vulcanization of transitional layer of all-steel load meridian tyre and performance tests of the tyre products

International Nuclear Information System (INIS)

Zhang Benshang; Zhu Chengshen; Ying Shizhou; Liu Kebo; Li Zhaopeng; Li Kunhao; Zhang Hongna; Zhao Meihong; Yang Mingcheng

2012-01-01

In this article, natural rubber is chosen as transitional layer of all-steel load meridian tyre, which is pre-vulcanized by 500 keV E-beam irradiation of up to 60 kGy. The results show that the Green strength of transitional layer increases with the dose, reaching four times at 60 kGy as much as the control (without irradiation). The viscosity of transitional layer increases rapidly below about 29 kGy, but changes little at higher doses. The final mechanical properties do not differ significantly from those of the control. However, thickness of the natural rubber transitional layer for an average single tire can be reduced by 1 mm (or 1.5 kg), without obvious adverse effect on the tyre performance. (authors)

FTIR spectra and mechanical strength analysis of some selected rubber derivatives

Science.gov (United States)

Gunasekaran, S.; Natarajan, R. K.; Kala, A.

2007-10-01

Rubber materials have wide range of commercial applications such as, infant diapers, famine hygiene products, drug delivery devices and incontinency products such as rubber tubes, tyres, etc. In the present work, studies on mechanical properties of some selected rubber materials viz., natural rubber (NR), styrene butadiene rubber (SBR), nitrile butadiene rubber (NBR) and ethylene propylene diene monomer (EPDM) have been carried out in three states viz., raw, vulcanized and reinforced. To enhance the quality of rubber elastomers, an attempt is made to prepare new elastomers called polyblends. In the present study an attempt is made to blend NR with NBR and with EPDM. We here report, a novel approach for the evaluation of various physico-mechanical properties such as mechanical strength, tensile strength, elongation and hardness. The method is simple, direct and fast and involves infrared spectral measurements for the evaluation of these properties. With the applications of modern infrared spectroscopy, the mechanical strength of these rubber materials have been analyzed by calculating the internal standards among the methyl and methylene group vibrational frequencies obtained from FTIR spectroscopy. Also the tensile strength measurements carried out by universal testing machine. The results pertaining physico-mechanical properties of the rubber derivatives undertaken in the present study obtained by IR-based method are in good agreement with data resulted from the standard methods.

Degradation of non-vulcanized natural rubber - renewable resource for fine chemicals used in polymer synthesis

Directory of Open Access Journals (Sweden)

Alexander Fainleib

2013-01-01

Full Text Available In the current scenario, there is growing interest in the products of degradation of rubber (natural and synthetic for specific applications in different industry sectors, whose benefits in replacing conventionally used products are mainly related to sustainability. Since the degradation products of rubber can be used in different areas, several research groups may have the interest aroused by these products, but are not familiar with the aspects related to the chemical behavior of rubber. This review aims to bring together the key information in the published literature on the degradation of natural rubber, emphasizing metatheses reactions, oxidative damage and splitting of the double bond, in order to serve as a reference source for researchers from different fields interested in obtaining such kind of products. The structures and properties as well as additional chemical transformations resulting in oligomers of isoprene, functionalised oligomers and polymers based on both are also described.

Pengaruh suhu vulkanisasi terhadap sifat mekanis vulkanisat karet alam dan karet akrilonitril-butadiena

OpenAIRE

Norma Arisanti Kinasih; Muhammad Irfan Fathurrohman; Dadang Suparto

2015-01-01

Natural and acrylonitrile-butadiene rubbers possess different vulcanization characteristics. Selection of the vulcanization system and temperature affects the mechanical properties of vulcanized natural rubber (NR) and acrylonitrile-butadiene rubber (NBR). In the present work, the effect of vulcanization temperature (150, 160, 170 and 180oC) on the mechanical properties of NR and NBR vulcanizates was studied. The effect of different vulcanization system (semi efficient, efficient and sulfur d...

Effect of organo-clay on the dielectric relaxation response of silicone rubber

International Nuclear Information System (INIS)

Gharavi, N; Razzaghi-Kashani, M; Golshan-Ebrahimi, N

2010-01-01

Dielectric elastomers are light weight, low-cost, highly deformable and fast response smart materials capable of converting electrical energy into mechanical work or vice versa. Silicone rubber is a well-known dielectric elastomer which is used as actuator, and in order to enhance the efficiency of this smart material, compounding of silicone rubber with various fillers can be carried out. The effect of organically modified montmorillonite (OMMT) nano-clay on improvement of dielectric properties, actuation stress and its relaxation response was considered in this study. OMMT was dispersed in room temperature vulcanized (RTV) silicone rubber, and a composite film was cast. Using an in-house actuation set-up, it was shown that the actuation stress for a given electric field intensity is higher for composites than that for pristine silicone rubber. Also, the time-dependent actuation response of the samples was evaluated, and it was shown that the characteristic relaxation time of the actuation stress for composites is less than for the pristine rubber as a result of OMMT addition

Carbon Stocks across a Fifty Year Chronosequence of Rubber Plantations in Tropical China

Directory of Open Access Journals (Sweden)

Chenggang Liu

2017-06-01

Full Text Available Transition from forest to rubber (Hevea brasiliensis Muell. Arg. plantation has occurred in tropical China for decades. Rubber has been planted on 1 million ha to provide raw materials to the rubber industry. The role of various-aged rubber plantations in carbon (C sequestration remains unclear. The biomass C accumulation including latex C and C distribution in soil of five different-aged stands (7, 13, 19, 25 and 47 years old were examined. The total biomass C stock (TBC and total net primary productivity (NPPtotal, whether with or without latex C, had a close quadratic relationship with stand age. Regardless of stand age, around 68% of the C was stored in aboveground biomass, and NPPlatex contributed to approximately 18% of C sequestration. Soil organic carbon stock in the 100-cm depth remained relatively stable, but it lost about 16.8 Mg ha−1 with stand age. The total ecosystem C stock (TEC across stands averaged 159.6, 174.4, 229.6, 238.1 and 291.9 Mg ha−1, respectively, of which more than 45% was stored in the soil. However, biomass would become the major C sink rather than soil over a maximal rubber life expectancy. Regression analysis showed that TEC for rubber plantation at 22 years is comparable to a baseline of 230.4 Mg ha−1 for tropical forest in China, and would reach the maximum value at around 54 years. Therefore, rubber plantation can be considered as alternative land use without affecting net forest ecosystem C storage. In addition to the potential C gains, a full set of ecosystem and economic properties have to be quantified in order to assess the trade-offs associated with forest-to-rubber transition.

Efeito de um resíduo do processo de galvanoplastia sobre a vulcanização da borracha natural (NR Effect from the waste from the electroplating process on the natural rubber (NR vulcanization

Directory of Open Access Journals (Sweden)

Alex C. S. Santos

2009-01-01

Full Text Available Um resíduo gerado no processo de galvanoplastia (RG, rico em metais, foi incorporado em composições de borracha natural (NR em substituição parcial ou total ao ativador comum do processo de vulcanização, o óxido de zinco (ZnO. As diferentes misturas foram preparadas em um misturador de calandras e, após a reometria, foram vulcanizadas a 150 °C. As propriedades mecânicas de resistência à tração e rasgo foram determinadas, além do teor de gel. Além disso, o efeito do resíduo RG sobre a cinética de vulcanização foi analisado através do modelo de Coran, usando-se as temperaturas de 150, 160 e 170 °C. Os resultados mostraram que RG desenvolve algum efeito catalítico sobre a vulcanização de NR, embora exista uma considerável perda na resistência à tração quando o teor de RG excede o do ZnO nas composições. Quanto ao rasgo, a propriedade é mantida em um patamar satisfatório enquanto teores menores de RG são utilizados.A waste generated in the electroplating process (RG, rich in metals, was incorporated in natural rubber (NR compositions, as a partial or complete replacement of zinc oxide (ZnO, which is a typical activator of the vulcanization process. Different mixtures were prepared in a two-roll mixer, which were vulcanized at 150 ºC after the rheometry measurements. Mechanical properties such as tensile and tear strength were evaluated, as well as the gel content. In addition, the effect of RG waste upon the vulcanization kinetics was analyzed with the Coran model using temperatures at 150, 160 and 170 ºC. The results showed that RG develops some catalytic effect upon NR vulcanization, but there is a poor mechanical performance when RG loading is higher than that of ZnO in the compositions. For the tear strength, the property is maintained at a reasonable level if a small RG loading is utilized.

Expression of VEGF and collagen using a latex biomembrane as bladder replacement in rabbits

Directory of Open Access Journals (Sweden)

André Luís Alonso Domingos

2012-08-01

Full Text Available OBJECTIVE: To investigate the VEGF expression and collagen deposition using a latex biomembrane as bladder replacement in rabbits. MATERIALS AND METHODS: After partial cystectomy, a patch of a non-vulcanized latex biomembrane (2 x 2 cm was sewn to the bladder of rabbits with 5/0 monofilament polydioxanone sulfate sutures in a watertight manner. Groups of 5 animals were killed at 15, 45 and 90 days after surgery and the bladder was removed. Sections of 5µm were cut and stained with picrosirius-red in order to estimate the amount of extracellular matrix in the graft. To confirm the presence of VEGF in tissues, protein expression was determined by immunohistochemistry. RESULTS: No death, urinary leakage or graft extrusion occurred in any group. All bladders showed a spherical shape. A progressive reduction in the amount of collagen occurred in the graft area and was negatively and linearly correlated with time (p < 0.001. VEGF expression was higher in grafted areas when compared to controls at 15 and 45 days after surgery and decreased with time (p < 0.001. CONCLUSION: The latex biomembrane as a matrix for partial bladder replacement in rabbits promotes temporary collagen deposition and stimulates the angiogenic process.

Properties of Natural Rubber-Based Composites Containing Fullerene

Directory of Open Access Journals (Sweden)

Omar A. Al-Hartomy

2012-01-01